Technical Information on the Carbonation of the EBR-II Reactor, Summary Report Part 1: Laboratory Experiments and Application to EBR-II Secondary Sodium System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Steven R. Sherman

Residual sodium is defined as sodium metal that remains behind in pipes, vessels, and tanks after the bulk sodium metal has been melted and drained from such components. The residual sodium has the same chemical properties as bulk sodium, and differs from bulk sodium only in the thickness of the sodium deposit. Typically, sodium is considered residual when the thickness of the deposit is less than 5-6 cm. This residual sodium must be removed or deactivated when a pipe, vessel, system, or entire reactor is permanently taken out of service, in order to make the component or system safer and/ormore » to comply with decommissioning regulations. As an alternative to the established residual sodium deactivation techniques (steam-and-nitrogen, wet vapor nitrogen, etc.), a technique involving the use of moisture and carbon dioxide has been developed. With this technique, sodium metal is converted into sodium bicarbonate by reacting it with humid carbon dioxide. Hydrogen is emitted as a by-product. This technique was first developed in the laboratory by exposing sodium samples to humidified carbon dioxide under controlled conditions, and then demonstrated on a larger scale by treating residual sodium within the Experimental Breeder Reactor II (EBR-II) secondary cooling system, followed by the primary cooling system, respectively. The EBR-II facility is located at the Idaho National Laboratory (INL) in southeastern Idaho, U.S.A. This report is Part 1 of a two-part report. It is divided into three sections. The first section describes the chemistry of carbon dioxide-water-sodium reactions. The second section covers the laboratory experiments that were conducted in order to develop the residual sodium deactivation process. The third section discusses the application of the deactivation process to the treatment of residual sodium within the EBR-II secondary sodium cooling system. Part 2 of the report, under separate cover, describes the application of the technique to residual sodium treatment within the EBR-II primary sodium cooling system and related systems.« less

Porous Hard Carbon Derived from Walnut Shell as an Anode Material for Sodium-Ion Batteries

NASA Astrophysics Data System (ADS)

Zhang, Sensen; Li, Ying; Li, Min

2018-02-01

Porous hard carbon with large interlayer distance was fabricated from walnut shells through a facile high-temperature pyrolysis process and investigated as an anode material for sodium-ion batteries (SIBs). The results show that the electrochemical performance is mainly dependent on the pyrolysis temperature. The porous hard carbon, which was carbonized at 1300°C, displays the highest reversible capacity of 230 mAh g-1 at 20 mA g-1 and an excellent cycling stability (96% capacity retained over 200 cycles). The promising electrochemical performances are attributed to the porous structure reducing distances for sodium ion diffusion and expanded interlayer spacing, which is beneficial for sodium reversible insertion/extraction. The excellent electrochemical performance as well as the low-cost and environmental friendliness demonstrates that walnut shell-derived porous hard carbon is a promising anode material candidate for SIBs.

Facile synthesis of carbon-mediated porous nanocrystallite anatase TiO2 for improved sodium insertion capabilities as an anode for sodium-ion batteries

NASA Astrophysics Data System (ADS)

Wu, Feng; Luo, Rui; Xie, Man; Li, Li; Zhang, Xiaoxiao; Zhao, Luzi; Zhou, Jiahui; Wang, KangKang; Chen, Renjie

2017-09-01

Porous carbon-mediated nanocrystallite anatase TiO2 composites are synthesized successfully via a simple dilatory hydrolysis-calcination method. The structural and morphological characterizations reveal that carbon-mediated TiO2 with a carbon content of 9.9 wt % (C2-TiO2) shows a combination of mesoporous and macroporous structures with a pore volume of 0.20 cm3 g-1 and surface area of 40.3 m2 g-1. Notably, C2-TiO2 delivered enhanced electrochemical performances of a high charge capacity of 259 mA h g-1 at 0.1 C and a high rate performance of 110 mA h g-1 after 150 cycles, even at 1 C. A significant decrease is also observed in the electrochemical impedance of the carbon-mediated samples, which explains superior electrochemical performance. Compared with the bare anatase TiO2 (B-TiO2), improved sodium storage capabilities of carbon-mediated samples are attributed to the participation of carbon to form a symbiotic structure with TiO2, which not only increases pore volume of the samples but serves as highly conductive network to provide a Na+ diffusion path during the insertion/de-insertion of sodium ions. All of these encouraging results suggest that carbon-mediated TiO2 has a great potential for improving sodium insertion capabilities with a facile and low-cost synthesis process.

Inhibiting localized corrosion during storage of dilute SRP wastes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oblath, S.B.; Congdon, J.W.

1986-01-01

High-level radioactive waste will be incorporated in borosilicate glass in the Defense Waste Processing Facility (DWPF) at the Savannah River Plant (SRP). As part of this process, large volumes of inorganic salt wastes will be decontaminated for disposal as low-level waste. The principal contaminants, /sup 137/Cs and /sup 90/Sr, are removed by treatment with sodium tetraphenylborate and sodium titanate. The resulting solids will be slurried with a dilute salt solution and stored in existing carbon steel tanks for several years prior to processing and disposal. Initial tests indicated a tendency for localized corrosion of the tanks. An investigation, using nonradioactivemore » simulants for the expected solution compositions, identified inhibitors which would protect the steel. Changes in solution compositions over time, due to radiolytic effects, were also accounted for by the simulants. Six inhibitors were identified which would protect the steel tanks. The effects these inhibitors would have on later processing steps in the DWPF were then evaluated. After this process, only sodium nitrite remained as an inhibitor that was both effective and compatible with the DWPF. The use of this inhibitor has been demonstrated on a real waste slurry.« less

The effect of repeated sodium hypochlorite exposure on chlorine resistance development in Escherichia coli O157:H7

USDA-ARS?s Scientific Manuscript database

The emergence and spread of microorganisms with reduced susceptibility to antimicrobial agents is a major public health problem. Chlorine water has been widely used to reduce attached bacteria on the surface of food or for sanitizing the processing facilities. However, there are limited reports conc...

Bi2WO6 nanoflowers: An efficient visible light photocatalytic activity for ceftriaxone sodium degradation

NASA Astrophysics Data System (ADS)

Zhao, Yanyan; Wang, Yongbo; Liu, Enzhou; Fan, Jun; Hu, Xiaoyun

2018-04-01

The morphology-controlled synthesis of nano-structure photocatalyst have leaded a new possibility to improve their physical and chemical properties. Herein, Bi2WO6 nanocrystals (BWO) with nano-flower, nano plates, knot shape, rod like and irregular morphologies have been successfully synthesized through a highly facile hydrothermal process by simply adjusting pH values, reactive solvents and temperature. Photocatalytic activity of the as-prepared samples were evaluated by degradation of Ceftriaxone sodium under visible light irradiation (λ > 420 nm), the results indicated that all the BWO samples exhibit morphology-associated photocatalytic activity, and the 3D flowerlike-structure of BWO composed of well-ordered nano plates (BWO-D-5) displayed the outstanding photocatalytic activity. Through getting insight into the mechanism, h+ and rad O2- play major roles compared with rad OH in photocatalytic degradation process. The possible pathway of Ceftriaxone sodium and the intermediates were proposed to better understand the reaction process. Moreover, this work not only provides an example of morphology-dependent photocatalytic activity of BWO but also provides an illustrative example for removing organic pollutant molecules according to practical requirements.

Simplified Synthesis of Isotopically Labeled 5,5-Dimethyl-pyrroline N-Oxide

PubMed Central

Leinisch, Fabian; Jiang, JinJie; Deterding, Leesa J.; Mason, Ronald P.

2011-01-01

5,5-Dimethylpyrroline N-oxide (15N) and 5,5-di(trideuteromethyl)pyrroline N-oxide were synthesized from the respective isotopically labeled 2-nitropropane analogs obtained from the reaction of sodium nitrate with 2-halopropanes. This facile, straightforward process allows synthesizing isotopically labeled DMPO analogs in a 4-step reaction without special equipment. PMID:21986521

Tunnel-structured K xTiO 2 nanorods by in situ carbothermal reduction as a long cycle and high rate anode for sodium-ion batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Qing; Wei, Yaqing; Yang, Haotian

Here, the low electronic conductivity and the sluggish sodium-ion diffusion in the compact crystal structure of Ti-based anodes seriously restrict their development in sodium-ion batteries. In this study, a new hollandite K xTiO 2 with large (2 × 2) tunnels is synthesized by a facile carbothermal reduction method, and its sodium storage performance is investigated. X-ray diffraction (XRD) and transmission electron microscopy (TEM) analyses illustrate the formation mechanism of the hollandite K xTiO 2 upon the carbothermal reduction process. Compared to the traditional layered or small (1 × 1) tunnel-type Ti-based materials, the hollandite K xTiO 2 with large (2more » × 2) tunnels may accommodate more sodium ions and facilitate the Na + diffusion in the structure; thus, it is expected to get a large capacity and realize high rate capability. The synthesized K xTiO 2 with large (2 × 2) tunnels shows a stable reversible capacity of 131 mAh g –1 (nearly 3 times of (1 × 1) tunnel-structured Na 2Ti 6O 13) and superior cycling stability with no obvious capacity decay even after 1000 cycles, which is significantly better than the traditional layered Na 2Ti 3O 7 (only 40% of capacity retention in 20 cycles). Moreover, the carbothermal process can naturally introduce oxygen vacancy and low-valent titanium as well as the surface carbon coating layer to the structure, which would greatly enhance the electronic conductivity of K xTiO 2 and thus endow this material high rate capability. With a good rate capability and long cyclability, this hollandite K xTiO 2 can serve as a new promising anode material for room-temperature long-life sodium-ion batteries for large-scale energy storage systems, and the carbothermal reduction method is believed to be an effective and facile way to develop novel Ti-based anodes with simultaneous carbon coating and Ti(III) self-doping.« less

Tunnel-structured K xTiO 2 nanorods by in situ carbothermal reduction as a long cycle and high rate anode for sodium-ion batteries

DOE PAGES

Zhang, Qing; Wei, Yaqing; Yang, Haotian; ...

2017-02-03

Here, the low electronic conductivity and the sluggish sodium-ion diffusion in the compact crystal structure of Ti-based anodes seriously restrict their development in sodium-ion batteries. In this study, a new hollandite K xTiO 2 with large (2 × 2) tunnels is synthesized by a facile carbothermal reduction method, and its sodium storage performance is investigated. X-ray diffraction (XRD) and transmission electron microscopy (TEM) analyses illustrate the formation mechanism of the hollandite K xTiO 2 upon the carbothermal reduction process. Compared to the traditional layered or small (1 × 1) tunnel-type Ti-based materials, the hollandite K xTiO 2 with large (2more » × 2) tunnels may accommodate more sodium ions and facilitate the Na + diffusion in the structure; thus, it is expected to get a large capacity and realize high rate capability. The synthesized K xTiO 2 with large (2 × 2) tunnels shows a stable reversible capacity of 131 mAh g –1 (nearly 3 times of (1 × 1) tunnel-structured Na 2Ti 6O 13) and superior cycling stability with no obvious capacity decay even after 1000 cycles, which is significantly better than the traditional layered Na 2Ti 3O 7 (only 40% of capacity retention in 20 cycles). Moreover, the carbothermal process can naturally introduce oxygen vacancy and low-valent titanium as well as the surface carbon coating layer to the structure, which would greatly enhance the electronic conductivity of K xTiO 2 and thus endow this material high rate capability. With a good rate capability and long cyclability, this hollandite K xTiO 2 can serve as a new promising anode material for room-temperature long-life sodium-ion batteries for large-scale energy storage systems, and the carbothermal reduction method is believed to be an effective and facile way to develop novel Ti-based anodes with simultaneous carbon coating and Ti(III) self-doping.« less

Tunnel-Structured KxTiO2 Nanorods by in Situ Carbothermal Reduction as a Long Cycle and High Rate Anode for Sodium-Ion Batteries.

PubMed

Zhang, Qing; Wei, Yaqing; Yang, Haotian; Su, Dong; Ma, Ying; Li, Huiqiao; Zhai, Tianyou

2017-03-01

The low electronic conductivity and the sluggish sodium-ion diffusion in the compact crystal structure of Ti-based anodes seriously restrict their development in sodium-ion batteries. In this study, a new hollandite K x TiO 2 with large (2 × 2) tunnels is synthesized by a facile carbothermal reduction method, and its sodium storage performance is investigated. X-ray diffraction (XRD) and transmission electron microscopy (TEM) analyses illustrate the formation mechanism of the hollandite K x TiO 2 upon the carbothermal reduction process. Compared to the traditional layered or small (1 × 1) tunnel-type Ti-based materials, the hollandite K x TiO 2 with large (2 × 2) tunnels may accommodate more sodium ions and facilitate the Na + diffusion in the structure; thus, it is expected to get a large capacity and realize high rate capability. The synthesized K x TiO 2 with large (2 × 2) tunnels shows a stable reversible capacity of 131 mAh g -1 (nearly 3 times of (1 × 1) tunnel-structured Na 2 Ti 6 O 13 ) and superior cycling stability with no obvious capacity decay even after 1000 cycles, which is significantly better than the traditional layered Na 2 Ti 3 O 7 (only 40% of capacity retention in 20 cycles). Moreover, the carbothermal process can naturally introduce oxygen vacancy and low-valent titanium as well as the surface carbon coating layer to the structure, which would greatly enhance the electronic conductivity of K x TiO 2 and thus endow this material high rate capability. With a good rate capability and long cyclability, this hollandite K x TiO 2 can serve as a new promising anode material for room-temperature long-life sodium-ion batteries for large-scale energy storage systems, and the carbothermal reduction method is believed to be an effective and facile way to develop novel Ti-based anodes with simultaneous carbon coating and Ti(III) self-doping.

Sodium Hydroxide Production from Seawater Desalination Brine: Process Design and Energy Efficiency.

PubMed

Du, Fengmin; Warsinger, David M; Urmi, Tamanna I; Thiel, Gregory P; Kumar, Amit; Lienhard V, John H

2018-05-15

The ability to increase pH is a crucial need for desalination pretreatment (especially in reverse osmosis) and for other industries, but processes used to raise pH often incur significant emissions and nonrenewable resource use. Alternatively, waste brine from desalination can be used to create sodium hydroxide, via appropriate concentration and purification pretreatment steps, for input into the chlor-alkali process. In this work, an efficient process train (with variations) is developed and modeled for sodium hydroxide production from seawater desalination brine using membrane chlor-alkali electrolysis. The integrated system includes nanofiltration, concentration via evaporation or mechanical vapor compression, chemical softening, further ion-exchange softening, dechlorination, and membrane electrolysis. System productivity, component performance, and energy consumption of the NaOH production process are highlighted, and their dependencies on electrolyzer outlet conditions and brine recirculation are investigated. The analysis of the process also includes assessment of the energy efficiency of major components, estimation of system operating expense and comparison with similar processes. The brine-to-caustic process is shown to be technically feasible while offering several advantages, that is, the reduced environmental impact of desalination through lessened brine discharge, and the increase in the overall water recovery ratio of the reverse osmosis facility. Additionally, best-use conditions are given for producing caustic not only for use within the plant, but also in excess amounts for potential revenue.

Cold Trap Dismantling and Sodium Removal at a Fast Breeder Reactor - 12327

DOE Office of Scientific and Technical Information (OSTI.GOV)

Graf, A.; Petrick, H.; Stutz, U.

2012-07-01

The first German prototype Fast Breeder Nuclear Reactor (KNK) is currently being dismantled after being the only operating Fast Breeder-type reactor in Germany. As this reactor type used sodium as a coolant in its primary and secondary circuit, seven cold traps containing various amounts of partially activated sodium needed to be disposed of as part of the dismantling. The resulting combined difficulties of radioactive contamination and high chemical reactivity were handled by treating the cold traps differently depending on their size and the amount of sodium contained inside. Six small cold traps were processed onsite by cutting them up intomore » small parts using a band saw under a protective atmosphere. The sodium was then converted to sodium hydroxide by using water. The remaining large cold trap could not be handled in the same way due to its dimensions (2.9 m x 1.1 m) and the declared amount of sodium inside (1,700 kg). It was therefore manually dismantled inside a large box filled with a protective atmosphere, while the resulting pieces were packaged for later burning in a special facility. The experiences gained by KNK during this process may be advantageous for future dismantling projects in similar sodium-cooled reactors worldwide. The dismantling of a prototype fast breeder reactor provides the challenge not only to dismantle radioactive materials but also to handle sodium-contaminated or sodium-containing components. The treatment of sodium requires additional equipment and installations to ensure a safe handling. Since it is not permitted to bring sodium into a repository, all sodium has to be neutralized either through a controlled reaction with water or by incinerating. The resulting components can be disposed of as normal radioactive waste with no further conditions. The handling of sodium needs skilled and experienced workers to minimize the inherent risks. And the example of the disposal of the large KNK cold trap shows the interaction with others and also foreign decommissioning projects can provide solutions with were unknown before. (authors)« less

Four generations of sodium guide star lasers for adaptive optics in astronomy and space situational awareness

NASA Astrophysics Data System (ADS)

d'Orgeville, Céline; Fetzer, Gregory J.

2016-07-01

This paper recalls the history of sodium guide star laser systems used in astronomy and space situational awareness adaptive optics, analyzing the impact that sodium laser technology evolution has had on routine telescope operations. While it would not be practical to describe every single sodium guide star laser system developed to date, it is possible to characterize their evolution in broad technology terms. The first generation of sodium lasers used dye laser technology to create the first sodium laser guide stars in Hawaii, California, and Spain in the late 1980s and 1990s. These experimental systems were turned into the first laser guide star facilities to equip mediumto- large diameter adaptive optics telescopes, opening a new era of Laser Guide Star Adaptive Optics (LGS AO)-enabled diffraction-limited imaging from the ground. Although they produced exciting scientific results, these laser guide star facilities were large, power-hungry and messy. In the USA, a second-generation of sodium lasers was developed in the 2000s that used cleaner, yet still large and complex, solid-state laser technology. These are the systems in routine operation at the 8 to 10m-class astronomical telescopes and 4m-class satellite imaging facilities today. Meanwhile in Europe, a third generation of sodium lasers was being developed using inherently compact and efficient fiber laser technology, and resulting in the only commercially available sodium guide star laser system to date. Fiber-based sodium lasers are being or will soon be deployed at three astronomical telescopes and two space surveillance stations. These highly promising systems are still relatively large to install on telescopes and they remain significantly expensive to procure and maintain. We are thus proposing to develop a fourth generation of sodium lasers: based on semiconductor technology, these lasers could provide a definitive solution to the problem of sodium LGS AO laser sources for all astronomy and space situational awareness applications.

From Dye Laser Factory to Portable Semiconductor Laser: Four Generations of Sodium Guide Star Lasers for Adaptive Optics in Astronomy and Space Situational Awareness

NASA Astrophysics Data System (ADS)

d'Orgeville, C.; Fetzer, G.

This presentation recalls the history of sodium guide star laser systems used in astronomy and space situational awareness adaptive optics, analysing the impact that sodium laser technology evolution has had on routine telescope operations. While it would not be practical to describe every single sodium guide star laser system developed to date, it is possible to characterize their evolution in broad technology terms. The first generation of sodium lasers used dye laser technology to create the first sodium laser guide stars in Hawaii, California, and Spain in the late 1980's and 1990's. These experimental systems were turned into the first laser guide star facilities to equip medium-to-large diameter adaptive optics telescopes, opening a new era of LGS AO-enabled diffraction-limited imaging from the ground. Although they produced exciting scientific results, these laser guide star facilities were large, power-hungry and messy. In the USA, a second-generation of sodium lasers was developed in the 2000's that used cleaner, yet still large and complex, solid-state laser technology. These are the systems in routine operation at the 8-10m class astronomical telescopes and 4m-class satellite imaging facilities today. Meanwhile in Europe, a third generation of sodium lasers was being developed using inherently compact and efficient fiber laser technology, and resulting in the only commercially available sodium guide star laser system to date. Fiber-based sodium lasers will be deployed at two astronomical telescopes and at least one space debris tracking station this year. Although highly promising, these systems remain significantly expensive and they have yet to demonstrate high performance in the field. We are proposing to develop a fourth generation of sodium lasers: based on semiconductor technology, these lasers could provide the final solution to the problem of sodium laser guide star adaptive optics for all astronomy and space situational awareness applications.

Municipal sludge composting facility emissions -- comparison of wet scrubber and biofiltration control performance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Holzman, M.I.; Gammie, L.A.; Gilbert, P.E.

1997-12-31

The Metropolitan District (MDC) Water Pollution Control Plant located in Hartford, Connecticut operates a state-of-the-art composting facility to process municipal sewage sludge. An air emissions test program was performed to determine emission rates of criteria and non-criteria pollutants and to evaluate the performance of two types of emissions/odor control systems (biofiltration and wet scrubbing). The purpose of this report is to further the limited available emissions and control performance data on a municipal sewage sludge composting facility operation. The MDC`s sludge composting facility consists of a Biocell train and a Cure Cell train, each of which can currently receive approximatelymore » 20 wet tons per hour of sludge at 60% of full capacity. The minimum retention time in each train is 10.5 days. Air emissions from the Biocell train are treated by both a biofiltration system and a three-stage wet scrubber system. The biofilter and wet scrubber system operate in parallel, so as to allow direct comparison of performance. Emissions from the Cure Cell train are treated by a single biofiltration system. The wet scrubber system consists of a first stage reducing absorber (ammonia solution), followed by a second stage oxidation absorber (sodium hypochlorite and sulfuric acid), and a final residual scrubber (sodium hydroxide solution). The two biofiltration systems are identically sized at 10,000 square feet surface area and three feet depth. The emissions testing program was designed to obtain simultaneous inlet and outlet data across each control device. The measured pollutants included organo-sulfides, alcohols, aldehydes, ketones, pinenes, terpenes, total reduced sulfur compounds, chlorinated hydrocarbons, sulfuric acid, sodium hydroxide, ammonia, carbon monoxide and volatile organic compounds.« less

Development of high temperature liquid metal test facilities for qualification of materials and investigations of thermoelectrical modules

NASA Astrophysics Data System (ADS)

Onea, A.; Hering, W.; Reiser, J.; Weisenburger, A.; Diez de los Rios Ramos, N.; Lux, M.; Ziegler, R.; Baumgärtner, S.; Stieglitz, R.

2017-07-01

Three classes of experimental liquid metal facilities have been completed during the LIMTECH project aiming the qualification of materials, investigation of thermoelectrical modules, investigation of sodium transitional regimes and fundamental thermo-dynamical flows in concentrating solar power (CSP) relevant geometries. ATEFA facility is dedicated to basic science investigation focussed on the alkali metal thermal-to-electric converter (AMTEC) technology. Three SOLTEC facilities are aimed to be used in different laboratories for long term material investigation sodium environment up to a 1000 K temperature and for long term tests of AMTEC modules. The medium scale integral facility KASOLA is planned as the backbone for CSP development and demonstration.

Contamination sources, serogroups, biofilm-forming ability and biocide resistance of Listeria monocytogenes persistent in tilapia-processing facilities.

PubMed

Vázquez-Sánchez, Daniel; Galvão, Juliana Antunes; Oetterer, Marília

2017-11-01

The major contamination sources, serogroups, biofilm-forming ability and biocide resistance of Listeria monocytogenes persistent in tilapia-processing facilities were assessed. Twenty-five processing-control points were examined twice in two factories, including whole tilapias, frozen fillets, water and food-contact surfaces. L. monocytogenes were detected in 4 and 20% of points of Factory A and B respectively, but at low concentrations. Contamination was due to inadequate handling of tilapias in the slaughter room of Factory A and to the application of ineffective sanitizing procedures in Factory B. Seven strains were characterized by RAPD-PCR using primers HLWL85, OPM-01 and DAF4. Genotypic similarity allowed tracing the contamination source of tilapia fillets in Factory B and detecting a prevalent strain in Brazilian tilapia-processing facilities. The serogroup II (including the serotype 1/2c) was the most frequently found, followed by serogroup I (1/2a) and III (1/2b), whereas the serotype 4b was not detected. All strains showed high biofilm-forming ability on stainless steel and polystyrene, but biofilm formation was positively correlated with the type of origin surface. Biofilms were highly resistant to peracetic acid and sodium hypochlorite, being required doses higher than those recommended by manufacturers to be eradicated. Peracetic acid was more effective than sodium hypochlorite, but the use of disinfectants with similar mechanisms of action increases the risk of cross-resistance. Case-by-case approaches are thus recommended to determine the sources and degree of contamination present in each factory, which would allow applying precise responses to control the persistence of bacterial pathogens such as L. monocytogenes .

Facile synthesis of Sb2S3/MoS2 heterostructure as anode material for sodium-ion batteries.

PubMed

Zhang, Zhendong; Zhao, Jiachang; Xu, Meilan; Wang, Hongxia; Gong, Yanmei; Xu, Jingli

2018-05-18

A novel Sb2S3/MoS2 heterostructure in which Sb2S3 nanorods are coated with MoS2 nanosheets to form core-shell structure has been fabricated via a facile two-step hydrothermal process. The Sb2S3/MoS2 heterostructure utilized as anode of sodium-ion batteries (SIBs) shows higher capacity, superior rate capability and better cycling performance compared with individual Sb2S3 nanorods and MoS2 nanosheets. Specifically, the Sb2S3/MoS2 electrode shows an initial reversible capacity of 701 mAh g-1 at the current density of 100 mA g-1, which is remained 80.1% of the initial perforance after 100 cycles at the same current density. This outstanding electrochemical performance indicates Sb2S3/MoS2 heterostructure is a very promising anode material for high-performance SIBs. © 2018 IOP Publishing Ltd.

Desalination and hydrogen, chlorine, and sodium hydroxide production via electrophoretic ion exchange and precipitation.

PubMed

Shkolnikov, Viktor; Bahga, Supreet S; Santiago, Juan G

2012-08-28

We demonstrate and analyze a novel desalination method which works by electrophoretically replacing sodium and chloride in feed salt water with a pair of ions, calcium and carbonate, that react and precipitate out. The resulting calcium carbonate precipitate is benign to health, and can be filtered or settled out, yielding low ionic strength product water. The ion exchange and precipitation employs self-sharpening interfaces induced by movement of multiple ions in an electric field to prevent contamination of the product water. Simultaneously, the electrolysis associated with the electromigration produces hydrogen gas, chlorine gas, and sodium hydroxide. We conducted an experimental study of this method's basic efficacy to desalinate salt water from 100 to 600 mol m(-3) sodium chloride. We also present physicochemical models of the process, and analyze replacement reagents consumption, permeate recovery ratio, and energy consumption. We hypothesize that the precipitate can be recycled back to replacement reagents using the well-known, commercially implemented Solvay process. We show that the method's permeate recovery ratio is 58% to 46%, which is on par with that of reverse osmosis. We show that the method's energy consumption requirement over and above that necessary to generate electrolysis is 3 to 10 W h l(-1), which is on par with the energy consumed by state-of-the-art desalination methods. Furthermore, the method operates at ambient temperature and pressure, and uses no specialized membranes. The process may be feasible as a part of a desalination-co-generation facility: generating fresh water, hydrogen and chlorine gas, and sodium hydroxide.

40 CFR 60.489 - List of chemicals produced by affected facilities.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Resorcylic acid. 69-72-7 Salicylic acid. 127-09-3 Sodium acetate. 532-32-1 Sodium benzoate. 9004-32-4 Sodium... Benzoyl chloride. 100-51-6 Benzyl alcohol. 100-46-9 Benzylamine. 120-51-4 Benzyl benzoate. 100-44-7 Benzyl... 2-ethylhexanol. 122-51-0 Ethyl orthoformate. 95-92-1 Ethyl oxalate. 41892-71-1 Ethyl sodium...

40 CFR 60.489 - List of chemicals produced by affected facilities.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Resorcylic acid. 69-72-7 Salicylic acid. 127-09-3 Sodium acetate. 532-32-1 Sodium benzoate. 9004-32-4 Sodium... Benzoyl chloride. 100-51-6 Benzyl alcohol. 100-46-9 Benzylamine. 120-51-4 Benzyl benzoate. 100-44-7 Benzyl... 2-ethylhexanol. 122-51-0 Ethyl orthoformate. 95-92-1 Ethyl oxalate. 41892-71-1 Ethyl sodium...

40 CFR 60.489 - List of chemicals produced by affected facilities.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Resorcylic acid. 69-72-7 Salicylic acid. 127-09-3 Sodium acetate. 532-32-1 Sodium benzoate. 9004-32-4 Sodium... Benzoyl chloride. 100-51-6 Benzyl alcohol. 100-46-9 Benzylamine. 120-51-4 Benzyl benzoate. 100-44-7 Benzyl... 2-ethylhexanol. 122-51-0 Ethyl orthoformate. 95-92-1 Ethyl oxalate. 41892-71-1 Ethyl sodium...

The Effect of Carbonate, Oxalate and Peroxide on the Cesium Loading of Ionsiv IE-910 and IE-911

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fondeur, F.F.

2000-12-19

The Savannah River Site (SRS) continues to examine three processes for the removal of radiocesium from high-level waste. One option involves the use of crystalline silicotitanate (CST) as a non-elutable ion exchange medium. The process uses CST in its engineered form - IONSIV IE-911 made by UOP, LLC. - in a column to contact the liquid waste. Cesium exchanges with sodium ions residing inside the CST particles. The design disposes of the cesium-loaded CST by vitrification within the Defense Waste Processing Facility.

Commonly used disinfectants fail to eradicate Salmonella enterica biofilms from food contact surface materials.

PubMed

Corcoran, M; Morris, D; De Lappe, N; O'Connor, J; Lalor, P; Dockery, P; Cormican, M

2014-02-01

Salmonellosis is the second most common cause of food-borne illness worldwide. Contamination of surfaces in food processing environments may result in biofilm formation with a risk of food contamination. Effective decontamination of biofilm-contaminated surfaces is challenging. Using the CDC biofilm reactor, the activities of sodium hypochlorite, sodium hydroxide, and benzalkonium chloride were examined against an early (48-h) and relatively mature (168-h) Salmonella biofilm. All 3 agents result in reduction in viable counts of Salmonella; however, only sodium hydroxide resulted in eradication of the early biofilm. None of the agents achieved eradication of mature biofilm, even at the 90-min contact time. Studies of activity of chemical disinfection against biofilm should include assessment of activity against mature biofilm. The difficulty of eradication of established Salmonella biofilm serves to emphasize the priority of preventing access of Salmonella to postcook areas of food production facilities.

Facile synthesis of highly active PdAu nanowire networks as self-supported electrocatalyst for ethanol electrooxidation.

PubMed

Hong, Wei; Wang, Jin; Wang, Erkang

2014-06-25

In recent years, direct ethanol fuel cells (DEFCs) are attracting increasing attention owing to their wide applications. However, a significant challenge in the development of DEFC technology is the urgent need for highly active anode catalysts for the ethanol oxidation reaction. In this work, a facile and reproducible method for the high-yield synthesis of PdAu nanowire networks is demonstrated. The whole synthetic process is very simple, just mixing Na2PdCl4, HAuCl4, and KBr in an aqueous solution and using polyvinylpyrrolidone as a protective reagent while sodium borohydride as a reductant. The whole synthetic process can be simply performed at room temperature and completed in 30 min, which can greatly simplify the synthetic process and lower the preparation cost. Electrochemical catalytic measurement results prove that the as-prepared catalysts exhibit dramatically enhanced electrocatalytic activity for ethanol electrooxidation in alkaline solution. The facile synthetic process and excellent catalytic performance of the as-prepared catalysts demonstrate that they can be used as a promising catalyst for DEFCs.

Sodium-Ion Batteries: Improving the Rate Capability of 3D Interconnected Carbon Nanofibers Thin Film by Boron, Nitrogen Dual-Doping.

PubMed

Wang, Min; Yang, Yang; Yang, Zhenzhong; Gu, Lin; Chen, Qianwang; Yu, Yan

2017-04-01

Boron, nitrogen dual-doping 3D hard carbon nanofibers thin film is synthesized using a facile process. The nanofibers exhibit high specific capacity and remarkable high-rate capability due to the synergistic effect of 3D porous structure, large surface area, and enlarged carbon layer spacing, and the B, N codoping-induced defects.

Comparison of Prescribed and Measured Dialysate Sodium: A Quality Improvement Project.

PubMed

Gul, Ambreen; Miskulin, Dana C; Paine, Susan S; Narsipur, Sriram S; Arbeit, Leonard A; Harford, Antonia M; Weiner, Daniel E; Schrader, Ronald; Horowitz, Bruce L; Zager, Philip G

2016-03-01

There is controversy regarding the optimal dialysate sodium concentration for hemodialysis patients. Dialysate sodium concentrations of 134 to 138 mEq/L may decrease interdialytic weight gain and improve hypertension control, whereas a higher dialysate sodium concentration may offer protection to patients with low serum sodium concentrations and hypotension. We conducted a quality improvement project to explore the hypothesis that prescribed and delivered dialysate sodium concentrations may differ significantly. Cross-sectional quality improvement project. 333 hemodialysis treatments in 4 facilities operated by Dialysis Clinic, Inc. Measure dialysate sodium to assess the relationships of prescribed and measured dialysate sodium concentrations. Magnitude of differences between prescribed and measured dialysate sodium concentrations. Dialysate sodium measured pre- and late dialysis. The least square mean of the difference between prescribed minus measured dialysate sodium concentration was -2.48 (95% CI, -2.87 to -2.10) mEq/L. Clinics with a greater number of different dialysate sodium prescriptions (clinic 1, n=8; clinic 2, n=7) and that mixed dialysate concentrates on site had greater differences between prescribed and measured dialysate sodium concentrations. Overall, 57% of measured dialysate sodium concentrations were within ±2 mEq/L of the prescribed dialysate sodium concentration. Differences were greater at higher prescribed dialysate sodium concentrations. We only studied 4 facilities and dialysate delivery machines from 2 manufacturers. Because clinics using premixed dialysate used the same type of machine, we were unable to independently assess the impact of these factors. Pressures in dialysate delivery loops were not measured. There were significant differences between prescribed and measured dialysate sodium concentrations. This may have beneficial or deleterious effects on clinical outcomes, as well as confound results from studies assessing the relationships of dialysate sodium concentrations to outcomes. Additional studies are needed to identify factors that contribute to differences between prescribed and measured dialysate sodium concentrations. Quality assurance and performance improvement (QAPI) programs should include measurements of dialysate sodium. Copyright © 2016 National Kidney Foundation, Inc. Published by Elsevier Inc. All rights reserved.

Experimental realization of dynamo action: present status and prospects

NASA Astrophysics Data System (ADS)

Giesecke, André; Stefani, Frank; Gundrum, Thomas; Gerbeth, Gunter; Nore, Caroline; Léorat, Jacques

2013-07-01

In the last decades, the experimental study of dynamo action has made great progress. However, after the dynamo experiments in Karlsruhe and Riga, the von-Kármán-Sodium (VKS) dynamo is only the third facility that has been able to demonstrate fluid flow driven self-generation of magnetic fields in a laboratory experiment. Further progress in the experimental examination of dynamo action is expected from the planned precession driven dynamo experiment that will be designed in the framework of the liquid sodium facility DRESDYN (DREsden Sodium facility for DYNamo and thermohydraulic studies). In this paper, we briefly present numerical models of the VKS dynamo that demonstrate the close relation between the axisymmetric field observed in that experiment and the soft iron material used for the flow driving impellers. We further show recent results of preparatory water experiments and design studies related to the precession dynamo and delineate the scientific prospects for the final set-up.

Verification Of The Defense Waste Processing Facility's (DWPF) Process Digestion Methods For The Sludge Batch 8 Qualification Sample

DOE Office of Scientific and Technical Information (OSTI.GOV)

Click, D. R.; Edwards, T. B.; Wiedenman, B. J.

2013-03-18

This report contains the results and comparison of data generated from inductively coupled plasma – atomic emission spectroscopy (ICP-AES) analysis of Aqua Regia (AR), Sodium Peroxide/Sodium Hydroxide Fusion Dissolution (PF) and Cold Chem (CC) method digestions and Cold Vapor Atomic Absorption analysis of Hg digestions from the DWPF Hg digestion method of Sludge Batch 8 (SB8) Sludge Receipt and Adjustment Tank (SRAT) Receipt and SB8 SRAT Product samples. The SB8 SRAT Receipt and SB8 SRAT Product samples were prepared in the SRNL Shielded Cells, and the SRAT Receipt material is representative of the sludge that constitutes the SB8 Batch ormore » qualification composition. This is the sludge in Tank 51 that is to be transferred into Tank 40, which will contain the heel of Sludge Batch 7b (SB7b), to form the SB8 Blend composition.« less

Renewable-juglone-based high-performance sodium-ion batteries.

PubMed

Wang, Hua; Hu, Pengfei; Yang, Jie; Gong, Guangming; Guo, Lin; Chen, Xiaodong

2015-04-08

A renewable-biomolecule-based electrode is developed through a facile synchronous reduction and self-assembly process, without any binder or additional conductive agent. The hybridized electrodes can be fabricated with arbitrary size and shape and exhibit superior capacity and cycle performance. The renewable-biomaterial-based high-performance electrodes will hold a place in future energy-storage devices. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Post-test analysis of dryout test 7B' of the W-1 Sodium Loop Safety Facility Experiment with the SABRE-2P code. [LMFBR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rose, S.D.; Dearing, J.F.

An understanding of conditions that may cause sodium boiling and boiling propagation that may lead to dryout and fuel failure is crucial in liquid-metal fast-breeder reactor safety. In this study, the SABRE-2P subchannel analysis code has been used to analyze the ultimate transient of the in-core W-1 Sodium Loop Safety Facility experiment. This code has a 3-D simple nondynamic boiling model which is able to predict the flow instability which caused dryout. In other analyses dryout has been predicted for out-of-core test bundles and so this study provides additional confirmation of the model.

Facile Synthesis of Radial-Like Macroporous Superparamagnetic Chitosan Spheres with In-Situ Co-Precipitation and Gelation of Ferro-Gels

PubMed Central

Yang, Chih-Hui; Wang, Chih-Yu; Huang, Keng-Shiang; Yeh, Chen-Sheng; Wang, Andrew H. -J.; Wang, Wei-Ting; Lin, Ming-Yu

2012-01-01

Macroporous chitosan spheres encapsulating superparamagnetic iron oxide nanoparticles were synthesized by a facile and effective one-step fabrication process. Ferro-gels containing ferrous cations, ferric cations and chitosan were dropped into a sodium hydroxide solution through a syringe pump. In addition, a sodium hydroxide solution was employed for both gelation (chitosan) and co-precipitation (ferrous cations and ferric cations) of the ferro-gels. The results showed that the in-situ co-precipitation of ferro-ions gave rise to a radial morphology with non-spheroid macro pores (large cavities) inside the chitosan spheres. The particle size of iron oxide can be adjusted from 2.5 nm to 5.4 nm by tuning the concentration of the sodium hydroxide solution. Using Fourier Transform Infrared Spectroscopy and X-ray diffraction spectra, the synthesized nanoparticles were illustrated as Fe3O4 nanoparticles. In addition, the prepared macroporous chitosan spheres presented a super-paramagnetic behaviour at room temperature with a saturation magnetization value as high as ca. 18 emu/g. The cytotoxicity was estimated using cell viability by incubating doses (0∼1000 µg/mL) of the macroporous chitosan spheres. The result showed good viability (above 80%) with alginate chitosan particles below 1000 µg/mL, indicating that macroporous chitosan spheres were potentially useful for biomedical applications in the future. PMID:23226207

Hardware Progress Made in the Early Flight Fission Test Facilities (EFF-TF) To Support Near-Term Space Fission Systems

NASA Technical Reports Server (NTRS)

VanDyke, Melissa; Martin, James

2005-01-01

The EFF-TF provides a facility to experimentally evaluate thermal hydraulic issues through the use of highly effective non-nuclear testing. These techniques provide a rapid, more cost effective method of evaluating designs and support development risk mitigation when concerns are associated with non-nuclear aspects of space nuclear systems. For many systems, electrical resistance thermal simulators can be used to closely mimic the heat deposition of the fission process, providing axial and radial profiles. A number of experimental and design programs were underway in 2004. Initial evaluation of the SAFE-100a (19 module stainless steel/sodium heat pipe reactor with integral gas neat exchanger) was performed with tests up to 17.5 kW of input power at core temperatures of 1000 K. A stainless steel sodium SAFE-100 heat pipe module was placed through repeated freeze/thaw cyclic testing accumulating over 200 restarts to a temperature of 1000 K. Additionally, the design of a 37-fuel pin stainless steel pumped sodium/potassium (NaK) loop was finalized and components procured. Ongoing testing at the EFF-TF is geared towards facilitating both research and development necessary to field a near term space nuclear system. Efforts are coordinated with DOE laboratories, industry, universities, and other NASA centers. This paper describes some of the 2004 efforts.

3D Networked Tin Oxide/Graphene Aerogel with a Hierarchically Porous Architecture for High-Rate Performance Sodium-Ion Batteries.

PubMed

Xie, Xiuqiang; Chen, Shuangqiang; Sun, Bing; Wang, Chengyin; Wang, Guoxiu

2015-09-07

Low-cost and sustainable sodium-ion batteries are regarded as a promising technology for large-scale energy storage and conversion. The development of high-rate anode materials is highly desirable for sodium-ion batteries. The optimization of mass transport and electron transfer is crucial in the discovery of electrode materials with good high-rate performances. Herein, we report the synthesis of 3 D interconnected SnO2 /graphene aerogels with a hierarchically porous structure as anode materials for sodium-ion batteries. The unique 3 D architecture was prepared by a facile in situ process, during which cross-linked 3 D conductive graphene networks with macro-/meso-sized hierarchical pores were formed and SnO2 nanoparticles were dispersed uniformly on the graphene surface simultaneously. Such a 3 D functional architecture not only facilitates the electrode-electrolyte interaction but also provides an efficient electron pathway within the graphene networks. When applied as anode materials in sodium-ion batteries, the as-prepared SnO2 /graphene aerogel exhibited high reversible capacity, improved cycling performance compared to SnO2 , and promising high-rate capability. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Photographic Processing Interpretation Facility Wastewater Conceptual Treatment Design.

DTIC Science & Technology

1983-03-01

Total Chromium (Cr) - - - ɘ.05 - Copper (Cu) - - - ɘ.05 - Iron (Fe) - - - - - Manganese (Mn) - - - ɘ.03 - Mercury (Hg) - - - ɘ.004 - Potassium (K...8.3 - Silver (Ag) 2.2 7.0 17 0.15 2.2 Sodium (Na) - - - 8.2 - Zinc (Zn) - - - 0.12 - Biochemical Oxygen " Demand (BOD_) - - - 40 - Sulfate (SO...nonconventional pollutants include boron, dissolved sol i halides, iron, ammonia, nitrogen, phenols, sulfate and TOC. ,P,, 99 percent of the 11,000

Clinical Investigation Program Report.

DTIC Science & Technology

1983-10-01

metastatic to liver. (0) H-83-63. Double-blind, randomized parallel comparison of two different dosage regimens of naproxen sodium in patients with...different dosage regimens of naproxen sodium in patients with bone pain due to m etastatic cancer. Start Date: May 83 Est Comp Date: Indefinite Principal...Investigator: Facility: LTC D Gandara, MD LAMC CPT R Mansour, MD D ept/Svc: Associate Investigators: Hematology-Oncology Key Words: naproxen sodium

Posttest examination of Sodium Loop Safety Facility experiments. [LMFBR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Holland, J.W.

In-reactor, safety experiments performed in the Sodium Loop Safety Facility (SLSF) rely on comprehensive posttest examinations (PTE) to characterize the postirradiation condition of the cladding, fuel, and other test-subassembly components. PTE information and on-line instrumentation data, are analyzed to identify the sequence of events and the severity of the accident for each experiment. Following in-reactor experimentation, the SLSF loop and test assembly are transported to the Hot Fuel Examination Facility (HFEF) for initial disassembly. Goals of the HFEF-phase of the PTE are to retrieve the fuel bundle by dismantling the loop and withdrawing the test assembly, to assess the macro-conditionmore » of the fuel bundle by nondestructive examination techniques, and to prepare the fuel bundle for shipment to the Alpha-Gamma Hot Cell Facility (AGHCF) at Argonne National Laboratory.« less

A densely packed Sb2O3 nanosheet-graphene aerogel toward advanced sodium-ion batteries.

PubMed

Zhou, Jing; Yan, Bingyi; Yang, Jie; Yang, Yun; Zhou, Wei; Lan, Hao; Wang, Hua; Guo, Lin

2018-05-17

As a promising anodic material for rechargeable batteries, Sb2O3 has drawn increasing attention due to its high theoretical capacity and abundant natural deposits. However, poor cyclability and rate performance of Sb2O3 derived from a large volume change during insertion/desertion reactions as well as a sluggish kinetic process restrict its practical application. Herein, we report a facile amorphous-to-crystalline strategy to synthesize a densely packed Sb2O3 nanosheet-graphene aerogel as a novel anode for sodium ion batteries (SIBs). This Sb2O3/graphene composite displays a reversible capacity as high as 657.9 mA h g-1 even after 100 cycles at 0.1 A g-1, along with an excellent rate capacity of 356.8 mA h g-1 at 5.0 A g-1. The superior electrochemical performance is attributed to the synergistic effects of densely packed Sb2O3 nanosheets and graphene aerogel, which serves as both a robust support and stable buffer layer to maintain the structural stability of the nanocomposite, and enhances the electrode kinetics of electrolyte diffusion and electron transfer simultaneously. Hence, this densely-packed two-dimensional Sb2O3 nanosheet-graphene aerogel can be a promising anode material for rechargeable SIBs due to its facile synthesis process and outstanding electrochemical performance.

Recent and future liquid metal experiments on homogeneous dynamo action and magnetic instabilities

NASA Astrophysics Data System (ADS)

Stefani, Frank; Gerbeth, Gunter; Giesecke, Andre; Gundrum, Thomas; Kirillov, Oleg; Seilmayer, Martin; Gellert, Marcus; Rüdiger, Günther; Gailitis, Agris

2011-10-01

The present status of the Riga dynamo experiment is summarized and the prospects for its future exploitation are evaluated. We further discuss the plans for a large-scale precession driven dynamo experiment to be set-up in the framework of the new installation DRESDYN (DREsden Sodium facility for dynamo and thermohydraulic studies) at Helmholtz-Zentrum Dresden-Rossendorf. We report recent investigations of the magnetorotational instability and the Tayler instability and sketch the plans for another large-scale liquid sodium facility devoted to the combined study of both effects.

LOW ACTIVITY WASTE FEED SOLIDS CARACTERIZATION AND FILTERABILITY TESTS

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCabe, D.; Crawford, C.; Duignan, M.

The primary treatment of the tank waste at the DOE Hanford site will be done in the Waste Treatment and Immobilization Plant (WTP) that is currently under construction. The baseline plan for the WTP Pretreatment facility is to treat the waste, splitting it into High Level Waste (HLW) feed and Low Activity Waste (LAW) feed. Both waste streams are then separately vitrified as glass and sealed in canisters. The LAW glass will be disposed onsite in the Integrated Disposal Facility (IDF). There are currently no plans to treat the waste to remove technetium in the WTP Pretreatment facility, so itsmore » disposition path is the LAW glass. Options are being explored to immobilize the LAW portion of the tank waste, i.e., the LAW feed from the WTP Pretreatment facility. Removal of {sup 99}Tc from the LAW Feed, followed by off-site disposal of the {sup 99}Tc, would eliminate a key risk contributor for the IDF Performance Assessment (PA) for supplemental waste forms, and has potential to reduce treatment and disposal costs. Washington River Protection Solutions (WRPS) is developing some conceptual flow sheets for LAW treatment and disposal that could benefit from technetium removal. One of these flowsheets will specifically examine removing {sup 99}Tc from the LAW feed stream to supplemental immobilization. The conceptual flow sheet of the {sup 99}Tc removal process includes a filter to remove insoluble solids prior to processing the stream in an ion exchange column, but the characteristics and behavior of the liquid and solid phases has not previously been investigated. This report contains results of testing of a simulant that represents the projected composition of the feed to the Supplemental LAW process. This feed composition is not identical to the aqueous tank waste fed to the Waste Treatment Plant because it has been processed through WTP Pretreatment facility and therefore contains internal changes and recycle streams that will be generated within the WTP process. Although a Supplemental LAW feed simulant has previously been prepared, this feed composition differs from that simulant because those tests examined only the fully soluble aqueous solution at room temperature, not the composition formed after evaporation, including the insoluble solids that precipitate after it cools. The conceptual flow sheet for Supplemental LAW immobilization has an option for removal of {sup 99}Tc from the feed stream, if needed. Elutable ion exchange has been selected for that process. If implemented, the stream would need filtration to remove the insoluble solids prior to processing in an ion exchange column. The characteristics, chemical speciation, physical properties, and filterability of the solids are important to judge the feasibility of the concept, and to estimate the size and cost of a facility. The insoluble solids formed during these tests were primarily natrophosphate, natroxalate, and a sodium aluminosilicate compound. At the elevated temperature and 8 M [Na+], appreciable insoluble solids (1.39 wt%) were present. Cooling to room temperature and dilution of the slurry from 8 M to 5 M [Na+] resulted in a slurry containing 0.8 wt% insoluble solids. The solids (natrophosphate, natroxalate, sodium aluminum silicate, and a hydrated sodium phosphate) were relatively stable and settled quickly. Filtration rates were in the range of those observed with iron-based simulated Hanford tank sludge simulants, e.g., 6 M [Na+] Hanford tank 241-AN-102, even though their chemical speciation is considerably different. Chemical cleaning of the crossflow filter was readily accomplished with acid. As this simulant formulation was based on an average composition of a wide range of feeds using an integrated computer model, this exact composition may never be observed. But the test conditions were selected to enable comparison to the model to enable improving its chemical prediction capability.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Russell, Renee L.; Fiskum, Sandra K.; Smoot, Margaret R.

Washington River Protection Solutions (WRPS) is developing a Low-Activity Waste Pretreatment System (LAWPS) to provide low-activity waste (LAW) directly to the Hanford Tank Waste Treatment and Immobilization Plant (WTP) Low-Activity Waste Facility for immobilization. The pretreatment that will be conducted on tank waste supernate at the LAWPS facility entails filtration to remove entrained solids and cesium (Cs) ion exchange to remove Cs from the product sent to the WTP. Currently, spherical resorcinol-formaldehyde (sRF) resin (Microbeads AS, Skedsmokorset, Norway) is the Cs ion exchange resin of choice. Most work on Cs ion exchange efficacy in Hanford tank waste has been conductedmore » at nominally 5 M sodium (Na). WRPS is examining the possibility of processing supernatant at high Na concentrations—up to 8 M Na—to maximize processing efficiency through the LAWPS. Minimal Cs ion exchange work has been conducted at 6 M and 8 M Na concentrations..« less

Evaluation of standard and alternative methods for the decontamination of VX and HD in chemical agent disposal facilities. Final report, February 1992-February 1993

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hovanec, J.W.; Szafraniec, L.L.; Albizo, J.M.

1993-04-01

Standard decontaminant formulations, aqueous sodium hydroxide and aqueous sodium hypochlorite, were providing slow and incomplete results when used to decontaminate certain operating facilities at the Johnston Atoll Chemical Agent Disposal System and the Chemical Agent Disposal System (Utah). A study was undertaken to define the capabilities and limitations of using concentrated sodium hydroxide to decontaminate VX, the effect of adding hydrogen peroxide to the sodium hydroxide for the decontamination of VX, the efficacy of aqueous oxone for the decontamination of VX, and the efficacy of oxone in a water/1-methyl-2-pyrrolidinone (MP) mixture for the decontamination of HD. Using aqueous sodium hydroxidemore » alone was not desirable since the formation of toxic EA2192 could not be averted. However, the addition of hydrogen peroxide resulted in effective VX decontamination without EA2192 formation. Aqueous oxone was also found to be effective for both VX and HD. The incorporation of MP did little to improve HD dissolution and reacted with the oxone to reduce the effective usable life of the decontamination solution. Thus, the use of MP in HD decontamination was not recommended.« less

Facile fabrication of well-defined hydrogel beads with magnetic nanocomposite shells.

PubMed

Liu, Hongxia; Wang, Chaoyang; Gao, Quanxing; Chen, Jianxin; Ren, Biye; Liu, Xinxing; Tong, Zhen

2009-07-06

Well-defined magnetic nanocomposite beads with alginate gel cores and shells of iron oxide (gamma-Fe(2)O(3)) nanoparticles were prepared by self-assembly of colloidal particles at liquid-liquid interfaces and subsequent in situ gelation. Fe(2)O(3) nanoparticles could spontaneously adsorb onto the water droplet surfaces to stabilize water-in-hexane emulsions. Water droplets containing sodium alginate were in situ gelled by calcium cations, which were released from calcium-ethylenediamine tetraacetic acid (Ca-EDTA) chelate by decreasing pH value through slow hydrolysis of d-glucono-delta-lactone (GDL). The resulting hybrid beads with a core-shell structure were easily collected by removing hexane. This facile and high efficient fabrication had a 100% yield and could be carried out at room temperature. Insulin microcrystal was encapsulated into the hybrid beads by dispersing them in the aqueous solution of alginate sodium in the fabrication process. The sustained release could be obtained due to the dual barriers of the hydrogel core and the close-packed inorganic shell. The release curves were nicely fitted by the Weibull equation and the release followed Fickian diffusion. The hybrid beads may find applications as delivery vehicles for biomolecules, drugs, cosmetics, food supplements and living cells.

Spent fuel treatment at ANL-West

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goff, K.M.; Benedict, R.W.; Levinskas, D.

1994-12-31

At Argonne National Laboratory-West (ANL-West) there are several thousand kilograms of metallic spent nuclear fuel containing bond sodium. This fuel will be treated in the Fuel Cycle Facility at ANL-West to produce stable waste forms for storage and disposal. The treatment operations will employ a pyrochemical process that also has applications for treating most of the fuel types within the Department of Energy complex. The treatment equipment is in its last stage of readiness, and operations will begin in the Fall of 1994.

Fabrication of monodispersed nickel flower-like architectures via a solvent-thermal process and analysis of their magnetic and electromagnetic properties

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kong Jing; Liu Wei, E-mail: jrliu@sdu.edu.cn; Wang Fenglong

Monodispersed Ni flower-like architectures with size of 1-2 {mu}m were synthesized through a facile solvent-thermal process in 1,2-propanediol solution in the presence of polyethylene glycol (PEG) and sodium alkali for electromagnetic absorption application. The Ni architectures are composed of nanoflakes, which assemble to form three dimensional flower-like structure, and the thickness of nanoflakes is about 10-40 nm. A possible formation mechanism for Ni flower-like architectures was proposed and it was confirmed by the control experiments. The Ni architectures exhibited a saturation magnetization (M{sub s}) of 47.7 emu/g and a large coercivity (H{sub cj}) of 332.3 Oe. The epoxy resin compositesmore » with 20 vol% Ni sample provided good electromagnetic wave absorption performance (reflection loss <-20 dB) in the range of 2.8-6.3 GHz over absorber thickness of 2.6-5.0 mm. - Graphical abstract: Monodispersed Ni flower-like architectures composed of nanoflakes were synthesized through a facile solvent-thermal process. The Ni architectures exhibited a large coercivity and enhanced electromagnetic wave absorption in GHz. Highlights: > Flower-like architectures composed of nanoflakes. > A possible formation mechanism for Ni flower-like architectures was proposed. > Sodium alkali, PEG, and NaCl played the important roles in the final morphology. > Ni architectures exhibited a large coercivity (H{sub cj}) of 332.3 Oe. > Efficient electromagnetic absorption (RL<-20 dB) was provided in 2.8-6.3 GHz.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

The High Ranking Facilities Deactivation Project (HRFDP), commissioned by the US Department of Energy Nuclear Materials and Facility Stabilization Program, is to place four primary high-risk surplus facilities with 28 associated ancillary facilities at Oak Ridge National Laboratory in a safe, stable, and environmentally sound condition as rapidly and economically as possible. The facilities will be deactivated and left in a condition suitable for an extended period of minimized surveillance and maintenance (S and M) prior to decontaminating and decommissioning (D and D). These four facilities include two reactor facilities containing spent fuel. One of these reactor facilities also containsmore » 55 tons of sodium with approximately 34 tons containing activated sodium-22, 2.5 tons of lithium hydride, approximately 100 tons of potentially contaminated lead, and several other hazardous materials as well as bulk quantities of contaminated scrap metals. The other two facilities to be transferred include a facility with a bank of hot cells containing high levels of transferable contamination and also a facility containing significant quantities of uranyl nitrate and quantities of transferable contamination. This work plan documents the objectives, technical requirements, and detailed work plans--including preliminary schedules, milestones, and conceptual FY 1996 cost estimates--for the Oak Ridge National Laboratory (ORNL). This plan has been developed by the Environmental Restoration (ER) Program of Lockheed Martin Energy Systems (Energy Systems) for the US Department of Energy (DOE) Oak Ridge Operations Office (ORO).« less

Phase change thermal storage for a solar total energy system

NASA Technical Reports Server (NTRS)

Rice, R. E.; Cohen, B. M.

1978-01-01

An analytical and experimental program is being conducted on a one-tenth scale model of a high-temperature (584 K) phase-change thermal energy storage system for installation in a solar total energy test facility at Albuquerque, New Mexico, U.S.A. The thermal storage medium is anhydrous sodium hydroxide with 8% sodium nitrate. The program will produce data on the dynamic response of the system to repeated cycles of charging and discharging simulating those of the test facility. Data will be correlated with a mathematical model which will then be used in the design of the full-scale system.

Superior Sodium Storage in 3D Interconnected Nitrogen and Oxygen Dual-Doped Carbon Network.

PubMed

Wang, Min; Yang, Zhenzhong; Li, Weihan; Gu, Lin; Yu, Yan

2016-05-01

Carbonaceous materials have attracted immense interest as anode materials for Na-ion batteries (NIBs) because of their good chemical, thermal stabilities, as well as high Na-storage capacity. However, the carbonaceous materials as anodes for NIBs still suffer from the lower rate capability and poor cycle life. An N,O-dual doped carbon (denoted as NOC) network is designed and synthesized, which is greatly favorable for sodium storage. It exhibits high specific capacity and ultralong cycling stability, delivering a capacity of 545 mAh g(-1) at 100 mA g(-1) after 100 cycles and retaining a capacity of 240 mAh g(-1) at 2 A g(-1) after 2000 cycles. The NOC composite with 3D well-defined porosity and N,O-dual doped induces active sites, contributing to the enhanced sodium storage. In addition, the NOC is synthesized through a facile solution process, which can be easily extended to the preparation of many other N,O-dual doped carbonaceous materials for wide applications in catalysis, energy storage, and solar cells. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Synthesis-microstructure-performance relationship of layered transition metal oxides as cathode for rechargeable sodium batteries prepared by high-temperature calcination.

PubMed

Xie, Man; Luo, Rui; Lu, Jun; Chen, Renjie; Wu, Feng; Wang, Xiaoming; Zhan, Chun; Wu, Huiming; Albishri, Hassan M; Al-Bogami, Abdullah S; El-Hady, Deia Abd; Amine, Khalil

2014-10-08

Research on sodium batteries has made a comeback because of concern regarding the limited resources and cost of lithium for Li-ion batteries. From the standpoint of electrochemistry and economics, Mn- or Fe-based layered transition metal oxides should be the most suitable cathode candidates for affordable sodium batteries. Herein, this paper reports a novel cathode material, layered Na1+x(Fey/2Niy/2Mn1-y)1-xO2 (x = 0.1-0.5), synthesized through a facile coprecipitation process combined with subsequent calcination. For such cathode material calcined at 800 °C for 20 h, the Na/Na1+x(Fey/2Niy/2Mn1-y)1-xO2 (x = 0.4) electrode exhibited a good capacity of 99.1 mAh g(-1) (cycled at 1.5-4.0 V) and capacity retention over 87% after 50 cycles. Optimization of this material would make layered transition metal oxides a strong candidate for the Na-ion battery cathode.

A Core Facility for the Study of Neurotoxins of Biological Origin

DTIC Science & Technology

1987-06-15

the animals were sacrificed with an intravenous overdose of sodium pentobarbital. The spilnal cords were removed rapidly and frozen in isopentane...control muscle receives no drug during 45Ca washout. Results: Ryanodine contracture 1. The effect of replacement of sodium by choline to block Na+ for...sodium by choline lowers the concentra- tion of ryanodine to cause a contracture from 10-4 M to 10- 6M and reduces the half time to peak tension from

Highly Porous FeS/Carbon Fibers Derived from Fe-Carrageenan Biomass: High-capacity and Durable Anodes for Sodium-Ion Batteries.

PubMed

Li, Daohao; Sun, Yuanyuan; Chen, Shuai; Yao, Jiuyong; Zhang, Yuhui; Xia, Yanzhi; Yang, Dongjiang

2018-05-08

The nanostructured metal sulfides have been reported as promising anode materials for sodium-ion batteries (SIBs) due to their high theoretical capacities but have suffered from the unsatisfactory electronic conductivity and poor structural stability during a charge/discharge process, thus limiting their applications. Herein, the one-dimensional (1D) porous FeS/carbon fibers (FeS/CFs) micro/nanostructures are fabricated through facile pyrolysis of double-helix-structured Fe-carrageenan fibers. The FeS nanoparticles are in situ formed by interacting with sulfur-containing group of natural material ι-carrageenan and uniformly embedded in the unique 1D porous carbon fibrous matrix, significantly enhancing the sodium-ion storage performance. The obtained FeS/CFs with optimized sodium storage performance benefits from the appropriate carbon content (20.9 wt %). The composite exhibits high capacity and excellent cycling stability (283 mAh g -1 at current density of 1 A g -1 after 400 cycles) and rate performance (247 mAh g -1 at 5 A g -1 ). This work provides a simple strategy to construct 1D porous FeS/CFs micro/nanostructures as high-performance anode materials for SIBs via a unique sustainable and environmentally friendly way.

Self-Assembled CoS Nanoflowers Wrapped in Reduced Graphene Oxides as the High-Performance Anode Materials for Sodium-Ion Batteries.

PubMed

Zhao, Yingying; Pang, Qiang; Meng, Yuan; Gao, Yu; Wang, Chunzhong; Liu, Bingbing; Wei, Yingjin; Du, Fei; Chen, Gang

2017-09-21

It remains a big challenge to identify high-performance anode materials to promote practical applications of sodium-ion batteries. Herein, the facile synthesis of CoS nanoflowers wrapped in reduced graphene oxides (RGO) is reported, and their sodium storage properties are systematically studied in comparison with bare CoS. The CoS@RGO nanoflowers deliver a high reversible capacity of 620 mAh g -1 at a current density of 100 mA g -1 and superior rate capability with discharge capacity of 329 mAh g -1 at 4 A g -1 , much higher than those of the bare CoS. Evidenced by electrochemical impedance spectra and ex-situ SEM images, the improvement in the sodium storage performance is found to be due to the introduction of RGO which serves as a conducting matrix, to not only increase the kinetic properties of CoS, but also buffer the volume change and maintain the integrity of working electrodes during (de)sodiation processes. More importantly, the pseudocapacitive contribution of more than 89 % is only observed in the CoS@RGO nanocomposites, owing to the enhanced specific area and surface redox behavior. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

SOLIDIFICATION OF THE HANFORD LAW WASTE STREAM PRODUCED AS A RESULT OF NEAR-TANK CONTINUOUS SLUDGE LEACHING AND SODIUM HYDROXIDE RECOVERY

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reigel, M.; Johnson, F.; Crawford, C.

2011-09-20

The U.S. Department of Energy (DOE), Office of River Protection (ORP), is responsible for the remediation and stabilization of the Hanford Site tank farms, including 53 million gallons of highly radioactive mixed wasted waste contained in 177 underground tanks. The plan calls for all waste retrieved from the tanks to be transferred to the Waste Treatment Plant (WTP). The WTP will consist of three primary facilities including pretreatment facilities for Low Activity Waste (LAW) to remove aluminum, chromium and other solids and radioisotopes that are undesirable in the High Level Waste (HLW) stream. Removal of aluminum from HLW sludge canmore » be accomplished through continuous sludge leaching of the aluminum from the HLW sludge as sodium aluminate; however, this process will introduce a significant amount of sodium hydroxide into the waste stream and consequently will increase the volume of waste to be dispositioned. A sodium recovery process is needed to remove the sodium hydroxide and recycle it back to the aluminum dissolution process. The resulting LAW waste stream has a high concentration of aluminum and sodium and will require alternative immobilization methods. Five waste forms were evaluated for immobilization of LAW at Hanford after the sodium recovery process. The waste forms considered for these two waste streams include low temperature processes (Saltstone/Cast stone and geopolymers), intermediate temperature processes (steam reforming and phosphate glasses) and high temperature processes (vitrification). These immobilization methods and the waste forms produced were evaluated for (1) compliance with the Performance Assessment (PA) requirements for disposal at the IDF, (2) waste form volume (waste loading), and (3) compatibility with the tank farms and systems. The iron phosphate glasses tested using the product consistency test had normalized release rates lower than the waste form requirements although the CCC glasses had higher release rates than the quenched glasses. However, the waste form failed to meet the vapor hydration test criteria listed in the WTP contract. In addition, the waste loading in the phosphate glasses were not as high as other candidate waste forms. Vitrification of HLW waste as borosilicate glass is a proven process; however the HLW and LAW streams at Hanford can vary significantly from waste currently being immobilized. The ccc glasses show lower release rates for B and Na than the quenched glasses and all glasses meet the acceptance criterion of < 4 g/L. Glass samples spiked with Re{sub 2}O{sub 7} also passed the PCT test. However, further vapor hydration testing must be performed since all the samples cracked and the test could not be performed. The waste loading of the iron phosphate and borosilicate glasses are approximately 20 and 25% respectively. The steam reforming process produced the predicted waste form for both the high and low aluminate waste streams. The predicted waste loadings for the monolithic samples is approximately 39%, which is higher than the glass waste forms; however, at the time of this report, no monolithic samples were made and therefore compliance with the PA cannot be determined. The waste loading in the geopolymer is approximately 40% but can vary with the sodium hydroxide content in the waste stream. Initial geopolymer mixes revealed compressive strengths that are greater than 500 psi for the low aluminate mixes and less than 500 psi for the high aluminate mixes. Further work testing needs to be performed to formulate a geopolymer waste form made using a high aluminate salt solution. A cementitious waste form has the advantage that the process is performed at ambient conditions and is a proven process currently in use for LAW disposal. The Saltstone/Cast Stone formulated using low and high aluminate salt solutions retained at least 97% of the Re that was added to the mix as a dopant. While this data is promising, additional leaching testing must be performed to show compliance with the PA. Compressive strength tests must also be performed on the Cast Stone monoliths to verify PA compliance. Based on testing performed for this report, the borosilicate glass and Cast Stone are the recommended waste forms for further testing. Both are proven technologies for radioactive waste disposal and the initial testing using simulated Hanford LAW waste shows compliance with the PA. Both are resistant to leaching and have greater than 25% waste loading.« less

TREATMENT OF A SATURATED ZONE HEXAVALENT CHROMIUM SOURCE AREA USING A FERROUS SULFATE/SODIUM DITHIONITE MIXTURE: A FIELD PILOT STUDY

EPA Science Inventory

A field pilot study was conducted to evaluate the performance of a combined ferrous sulfate/sodium dithionite solution for in situ treatment of a saturated zone hexavalent chromium source area at a former ferrochromium alloy production facility in Charleston, S.C. The saturate...

Evaluation of 5 cleaning and disinfection methods for nets used to collect zebrafish (Danio rerio).

PubMed

Collymore, Chereen; Porelli, Gina; Lieggi, Christine; Lipman, Neil S

2014-11-01

Few standardized methods of cleaning and disinfecting equipment in zebrafish facilities have been published, even though the effectiveness of these procedures is vital to preventing the transmission of pathogenic organisms. Four chemical disinfectants and rinsing with municipal tap water were evaluated for their ability to disinfect nets used to capture zebrafish. The disinfectants included benzalkonium chloride+methylene blue, sodium hypochlorite, chlorine dioxide, and potassium peroxymonosulfate+sodium chloride for a soak time of 5 or 30 min. Disinfection effectiveness was evaluated by using an ATP-based system that measured the reduction in absolute number and percentage of relative light units. In addition, nets were cultured aerobically on blood and MacConkey agar plates to determine the number of bacteria remaining after disinfection procedures. Soaking nets in sodium hypochlorite for 30 min and in potassium peroxymonosulfate+sodium chloride for 5 or 30 min were effective means of disinfection, according to at least 90% reduction in the number of relative light units and no bacterial growth after cleaning. These results will aid facility managers, veterinarians and investigators in selecting net cleaning and disinfection protocols.

Evaluation of 5 Cleaning and Disinfection Methods for Nets Used to Collect Zebrafish (Danio rerio)

PubMed Central

Collymore, Chereen; Porelli, Gina; Lieggi, Christine; Lipman, Neil S

2014-01-01

Few standardized methods of cleaning and disinfecting equipment in zebrafish facilities have been published, even though the effectiveness of these procedures is vital to preventing the transmission of pathogenic organisms. Four chemical disinfectants and rinsing with municipal tap water were evaluated for their ability to disinfect nets used to capture zebrafish. The disinfectants included benzalkonium chloride+methylene blue, sodium hypochlorite, chlorine dioxide, and potassium peroxymonosulfate+sodium chloride for a soak time of 5 or 30 min. Disinfection effectiveness was evaluated by using an ATP-based system that measured the reduction in absolute number and percentage of relative light units. In addition, nets were cultured aerobically on blood and MacConkey agar plates to determine the number of bacteria remaining after disinfection procedures. Soaking nets in sodium hypochlorite for 30 min and in potassium peroxymonosulfate+sodium chloride for 5 or 30 min were effective means of disinfection, according to at least 90% reduction in the number of relative light units and no bacterial growth after cleaning. These results will aid facility managers, veterinarians and investigators in selecting net cleaning and disinfection protocols. PMID:25650972

SIMULANT DEVELOPMENT FOR SAVANNAH RIVER SITE HIGH LEVEL WASTE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stone, M; Russell Eibling, R; David Koopman, D

2007-09-04

The Defense Waste Processing Facility (DWPF) at the Savannah River Site vitrifies High Level Waste (HLW) for repository internment. The process consists of three major steps: waste pretreatment, vitrification, and canister decontamination/sealing. The HLW consists of insoluble metal hydroxides (primarily iron, aluminum, magnesium, manganese, and uranium) and soluble sodium salts (carbonate, hydroxide, nitrite, nitrate, and sulfate). The HLW is processed in large batches through DWPF; DWPF has recently completed processing Sludge Batch 3 (SB3) and is currently processing Sludge Batch 4 (SB4). The composition of metal species in SB4 is shown in Table 1 as a function of the ratiomore » of a metal to iron. Simulants remove radioactive species and renormalize the remaining species. Supernate composition is shown in Table 2.« less

Electrolytic process to produce sodium hypochlorite using sodium ion conductive ceramic membranes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Balagopal, Shekar; Malhotra, Vinod; Pendleton, Justin

An electrochemical process for the production of sodium hypochlorite is disclosed. The process may potentially be used to produce sodium hypochlorite from seawater or low purity un-softened or NaCl-based salt solutions. The process utilizes a sodium ion conductive ceramic membrane, such as membranes based on NASICON-type materials, in an electrolytic cell. In the process, water is reduced at a cathode to form hydroxyl ions and hydrogen gas. Chloride ions from a sodium chloride solution are oxidized in the anolyte compartment to produce chlorine gas which reacts with water to produce hypochlorous and hydrochloric acid. Sodium ions are transported from themore » anolyte compartment to the catholyte compartment across the sodium ion conductive ceramic membrane. Sodium hydroxide is transported from the catholyte compartment to the anolyte compartment to produce sodium hypochlorite within the anolyte compartment.« less

Pseudocapacitive Sodium Storage by Ferroelectric Sn2 P2 S6 with Layered Nanostructure.

PubMed

Huang, Sheng; Meng, Chao; Xiao, Min; Ren, Shan; Wang, Shuanjin; Han, Dongmei; Li, Yuning; Meng, Yuezhong

2018-04-19

Sodium ion batteries (SIB) are considered promising alternative candidates for lithium ion batteries (LIB) because of the wide availability and low cost of sodium, therefore the development of alternative sodium storage materials with comparable performance to LIB is urgently desired. The sodium ions with larger sizes resist intercalation or alloying because of slow reaction kinetics. Most pseudocapacitive sodium storage materials are based on subtle nanomaterial engineering, which is difficult for large-scale production. Here, ferroelectric Sn 2 P 2 S 6 with layered nanostructure is developed as sodium ion storage material. The ferroelectricity-enhanced pseudocapacitance of sodium ion in the interlayer spacing makes the electrochemical reaction easier and faster, endowing the Sn 2 P 2 S 6 electrode with excellent rate capability and cycle stability. Furthermore, the facile solid state reaction synthesis and common electrode fabrication make the Sn 2 P 2 S 6 that becomes a promising anode material of SIB. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Development of Thermoacoustic Sensors for Sodium-cooled Fast Reactors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Heibel, Michael D.; Carvajal, Jorge V.; Ferroni, Paolo

This Final Report refers to the project “Development of Thermoacoustic Sensors for Sodium-cooled Fast Reactor Systems”, which was led by Westinghouse Electric Company (Westinghouse) and carried out in collaboration with Argonne National Laboratory (ANL) and University of Pittsburgh. Thermo-acoustic Power Sensors (TAPS) are self-powered, wireless sensors envisioned for measuring key parameters, such as local temperature and neutron flux, in a nuclear reactor core. This project was intended to specifically investigate their applicability to Sodium-cooled Fast Reactors (SFR). TAPS are non-invasive (wireless) and passive (self-powered) devices. The passivity derives from their ability to use conditions that “naturally” exist in a nuclearmore » reactor, such as gamma and neutron flux, as power sources. They generate oscillating pressure waves (i.e., sound waves) which, with a frequency and amplitude dependent upon these conditions, can travel through the core and associated structures, and reach the outside of the reactor vessel where a properly designed network of receivers can detect and interpret them. These receivers require a very small amount of power which, during loss of power events, can be provided for example by harvesting gamma radiation energy, thus resulting in a monitoring system that can function both during normal operation and during loss of power events. The project aimed at TAPS development through a series of tasks which are listed and briefly discussed as follows. TASK 1 – Sensor hardware design Subtask 1a: Assessment of sensor applications to SFRs Subtask 1b: Development of sensor functional requirements Subtask 1c: Definition of sensor hardware design specifications Task description: TAPS design was informed by considerations on their application (Subtask 1a), both the ultimate one in an SFR and the actual one in the ANL testing facilities that was intended to be used in support of the project. Considerations were made to identify optimum sensor design features that optimize the sensor size, materials, and output signal, for installation inside an SFR core. These considerations led to the development of Functional Requirements (Subtask 1b) and Design Requirements (Subtask 1c). TASK 2 – Sensor Hardware Manufacture Subtask 2a: Sensor hardware construction drawing development Subtask 2b: Sensor manufacture and assembly Task description: TAPS technical drawings were developed (Subtask 2a) using the Design Requirements established under Task 1. Subsequently, in spite of some problems which ultimately caused the program to be delayed, TAPS manufacturing was completed based on drawings (Subtask 2b). TASK 3 – Development of TAPS Signal Measurement System and TAPS Testing in Water Subtask 3a: Design, assembly and testing of signal measurement system, and TAPS testing in water Subtask 3b: Signal prediction-correction methodology development Task description: An assessment was performed on the techniques that can potentially be used to detect the signals emitted by the TAPS, e.g. a fiber-optic based acoustic signal measurement system, a laser vibrometer system, or an accelerometer-based system. The most suited technology, i.e. the accelerometer-based system, was developed further, and tested in water (Subtask 3a). Moreover, efforts were made to develop the methodology required to determine the actual system temperature and neutron flux distribution using differences between the measured and predicted TAPS responses (Subtask 3b). TASK 4 – Sensor System Testing in Sodium Subtask 4a: Test plan development Subtask 4b: Design, assembly and testing in small-scale sodium facility Subtask 4c: Design, assembly and testing in large-scale sodium and structures facility Task description: Upon proper test plan development (Subtask 4a), the fabricated TAPS was planned to be tested in sodium, by using two sodium facilities at ANL having different size and different purpose. The Under Sodium Viewing (USV) small-scale facility was intended to be used to investigate the effect of sodium on the sensor and its performance (Subtask 4b). The Mechanism Engineering Test Loop (METL) large-scale facility was instead intended to be used to assess the additional effect of prototypical SFR structures, such as fuel assembly mockup or parts of the core restrain structure, on sensor performance (Subtask 4c). As discussed in Section 3.2.2.7, unexpected issues during the TAPS manufacturing process resulted in some activities being delayed, with the TAPS and USV facility developed to the point to be ready for testing in sodium, however without the possibility to actually perform such testing (including the testing in METL) due to the end of the program’s performance period. Overall, through the development and testing (in water only) of two TAPS devices (a First-Generation TAPS followed by an optimized Second-Generation TAPS), the project confirmed the capability of this technology to generate acoustic signals proportional to temperature, which can be detected through a network of accelerometers identified as the best-suited type of receivers for acoustic signal detection. Moreover, the project also developed a computational model to predict the characteristics of the acoustic signals being generated, which combines thermal analysis of the TAPS with Finite Element Modeling (FEM)-aided acoustic characterization of the system. This model was benchmarked against experimental data collected during the project and, although general agreement was obtained, some limitations of the modeling methods were identified, which require additional development. Additional testing is needed in order to assess the effect, on TAPS operation and performance, of environmental changes resulting from the transition from water to liquid sodium. Such testing, which is suggested to be performed in the future, should look specifically at 1) both the effect resulting from the different thermoacoustic behavior of sodium (relative to water) and the effects of higher temperature on TAPS performance, and 2) the performance of the sensor-receiver system when multiple TAPS are used simultaneously and prototypical reactor structures are positioned in the testing environment. The latter testing is needed to assess the effects that potential signal attenuation/ distortion phenomena, as well as potential interference between signals emitted simultaneously, have on the performance of the technology for ultimate application in a nuclear reactor.« less

Extracting Silicon From Sodium-Process Products

NASA Technical Reports Server (NTRS)

Kapur, V.; Sanjurjo, A.; Sancier, K. M.; Nanis, L.

1982-01-01

New acid leaching process purifies silicon produced in reaction between silicon fluoride and sodium. Concentration of sodium fluoride and other impurities and byproducts remaining in silicon are within acceptable ranges for semi-conductor devices. Leaching process makes sodium reduction process more attractive for making large quantities of silicon for solar cells.

Nutritional Assessment of the Ft. Riley Non-Commissioned Officer Academy Dining Facility

DTIC Science & Technology

1987-05-01

Initiatives, Revised Armed Forces Recipe Service, Cholesterol Consumption, Sodium, Fat Reduction, Visual Portion Estimation. Garrison Dining Facility...moderate cholesterol intakes vii i Ue should be evaluated. Revised Armed Forces Recipe Service recipes with reduced salt content should be tested and...preparation methods used and recipes followed in the NCO Academy Dining Facility. Standard recipes from the Armed Forces Recipe Service Tri-Service

Component and Technology Development for Advanced Liquid Metal Reactors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anderson, Mark

2017-01-30

The following report details the significant developments to Sodium Fast Reactor (SFR) technologies made throughout the course of this funding. This report will begin with an overview of the sodium loop and the improvements made over the course of this research to make it a more advanced and capable facility. These improvements have much to do with oxygen control and diagnostics. Thus a detailed report of advancements with respect to the cold trap, plugging meter, vanadium equilibration loop, and electrochemical oxygen sensor is included. Further analysis of the university’s moving magnet pump was performed and included in a section ofmore » this report. A continuous electrical resistance based level sensor was built and tested in the sodium with favorable results. Materials testing was done on diffusion bonded samples of metal and the results are presented here as well. A significant portion of this work went into the development of optical fiber temperature sensors which could be deployed in an SFR environment. Thus, a section of this report presents the work done to develop an encapsulation method for these fibers inside of a stainless steel capillary tube. High temperature testing was then done on the optical fiber ex situ in a furnace. Thermal response time was also explored with the optical fiber temperature sensors. Finally these optical fibers were deployed successfully in a sodium environment for data acquisition. As a test of the sodium deployable optical fiber temperature sensors they were installed in a sub-loop of the sodium facility which was constructed to promote the thermal striping effect in sodium. The optical fibers performed exceptionally well, yielding unprecedented 2 dimensional temperature profiles with good temporal resolution. Finally, this thermal striping loop was used to perform cross correlation velocimetry successfully over a wide range of flow rates.« less

Trash to Treasure: From Harmful Algal Blooms to High-Performance Electrodes for Sodium-Ion Batteries.

PubMed

Meng, Xinghua; Savage, Phillip E; Deng, Da

2015-10-20

Harmful algal blooms (HABs) are frequently reported around the globe. HABs are typically caused by the so-called blue-green algae in eutrophic waters. These fast-growing HABs could be a good source for biomass. Unlike terrestrial plants, they need no land or soil. If HABs could be harvested on a large scale, it could not only possible to mitigate the issue of HABs but also provide a source of biomass. Herein, we demonstrate a facile procedure for converting the HABs into a promising high-performance negative-electrode material for sodium-ion batteries (SIBs). The carbon material derived from blue-green algae demonstrated promising electrochemical performance in reversible sodium storage. The algae used in this work was collected directly from Lake Erie during the algal blooms that affected 500 000 residents in Toledo in 2014. The carbon, derived from the freshly collected HABs by calcination in argon without any additional purification process, delivered a highly stable reversible specific capacity (∼230 mAh/g at a testing current of 20 mA/g) with nearly 100% Columbic efficiency in sodium storage. Impressive rate performance was achieved with a capacity of ∼135 mAh/g even after the testing current was increased fivefold. This proof of concept provides a promising route for mitigating the issue of HABs as "trash" and for generating high-capacity, low-cost electrodes for SIBs as "treasure".

Structural manipulation approaches towards enhanced sodium ionic conductivity in Na-rich antiperovskites

DOE PAGES

Wang, Yonggang; Wang, Qingfei; Liu, Zhenpu; ...

2015-06-10

High-performance solid electrolytes are critical for realizing all-solid-state batteries with enhance safety and cycling efficiency. However, currently available candidates (sulfides and the NASICON-typ ceramics) still suffer from drawbacks such as inflammability, high-cost and unfavorable machinability Here we present the structural manipulation approaches to improve the sodium ionic conductivity in series of affordable Na-rich antiperovskites. Experimentally, the whole solid solutions of Na 3OX (X ¼ Cl Br, I) are synthesized via a facile and timesaving route from the cheapest raw materials (Na, NaOH an NaX). The materials are nonflammable, suitable for thermoplastic processing due to low melting temperature (<300° C) withoutmore » decomposing. Notably, owing to the flexibility of perovskite-type structure it's feasible to control the local structure features by means of size-mismatch substitution an unequivalent-doping for a favorable sodium ionic diffusion pathway. Enhancement of sodium ioni conductivity by 2 magnitudes is demonstrated by these chemical tuning methods. The optimized sodiu ionic conductivity in Na 2.9Sr 0.05OBr 0.6I 0.4 bulk samples reaches 1.9 10 - 3 S/cm at 200° C and even highe at elevated temperature. Here, we believe further chemical tuning efforts on Na-rich antiperovskites wil promote their performance greatly for practical all-solid state battery applications.« less

Effect of surfactant amount on the morphology and magnetic properties of monodisperse ZnFe{sub 2}O{sub 4} nanoparticles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhao, Haitao, E-mail: zht95711lunwen@163.com; Liu, Ruiping; Zhang, Qiang

2016-03-15

Graphical abstract: Polyol process to monodisperse ZnFe{sub 2}O{sub 4} nanoparticles. - Highlights: • An one-step, facile and inexpensive synthetic route to monodisperse ZnFe{sub 2}O{sub 4} nanoparticles is described. • The sodium citrate stabilized ZnFe{sub 2}O{sub 4} nanoparticles with a diameter in the 5–8 nm size range can be easily dispersed in water. • The synthesis is very robust in terms of variations of experimental parameters. • ZnFe{sub 2}O{sub 4} nanoparticles present ferrimagnetic behavior at room temperature with a small hysteresis. - Abstract: The spinel ZnFe{sub 2}O{sub 4} ferrites with sodium citrate as a surfactant were fabricated by polyol process. Themore » effect of surfactant amount on the structure, morphology and magnetic properties of ZnFe{sub 2}O{sub 4} ferrites were investigated by X-ray diffraction(XRD), transmission electron microscope (TEM), thermogravimetric and differential scanning calorimetry (TG–DSC) and vibrating sample magnetometry (VSM), respectively. The results indicate that the structure of ZnFe{sub 2}O{sub 4} ferrites is a pure cubic spinel structure with a particle size of 5–8 nm. The dispersion of the synthesized ZnFe{sub 2}O{sub 4} is enhanced when the mole ratio of Fe(acac){sub 3} to sodium citrate decreases. The synthesized particles present ferrimagnetic behavior with a small hysteresis at room temperature. The increase of surfactant amount conversely leads to the decrease in the saturation magnetization value (Ms) especially when the mole ratio of Fe(acac){sub 3} to sodium citrate decreases to 8:3. Its Ms value is drastically reduced to 18.97 emu/g.« less

Fuel conditioning facility zone-to-zone transfer administrative controls.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pope, C. L.

2000-06-21

The administrative controls associated with transferring containers from one criticality hazard control zone to another in the Argonne National Laboratory (ANL) Fuel Conditioning Facility (FCF) are described. FCF, located at the ANL-West site near Idaho Falls, Idaho, is used to remotely process spent sodium bonded metallic fuel for disposition. The process involves nearly forty widely varying material forms and types, over fifty specific use container types, and over thirty distinct zones where work activities occur. During 1999, over five thousand transfers from one zone to another were conducted. Limits are placed on mass, material form and type, and container typesmore » for each zone. Ml material and containers are tracked using the Mass Tracking System (MTG). The MTG uses an Oracle database and numerous applications to manage the database. The database stores information specific to the process, including material composition and mass, container identification number and mass, transfer history, and the operators involved in each transfer. The process is controlled using written procedures which specify the zone, containers, and material involved in a task. Transferring a container from one zone to another is called a zone-to-zone transfer (ZZT). ZZTs consist of four distinct phases, select, request, identify, and completion.« less

Measurement of plasma decay processes in mixture of sodium and argon by coherent microwave scattering

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang Zhili; Shneider, Mikhail N.

2010-03-15

This paper presents the experimental measurement and computational model of sodium plasma decay processes in mixture of sodium and argon by using radar resonance-enhanced multiphoton ionization (REMPI), coherent microwave Rayleigh scattering of REMPI. A single laser beam resonantly ionizes the sodium atoms by means of 2+1 REMPI process. The laser beam can only generate the ionization of the sodium atoms and have negligible ionization of argon. Coherent microwave scattering in situ measures the total electron number in the laser-induced plasma. Since the sodium ions decay by recombination with electrons, microwave scattering directly measures the plasma decay processes of the sodiummore » ions. A theoretical plasma dynamic model, including REMPI of the sodium and electron avalanche ionization (EAI) of sodium and argon in the gas mixture, has been developed. It confirms that the EAI of argon is several orders of magnitude lower than the REMPI of sodium. The theoretical prediction made for the plasma decay process of sodium plasma in the mixture matches the experimental measurement.« less

An effective method to screen sodium-based layered materials for sodium ion batteries

NASA Astrophysics Data System (ADS)

Zhang, Xu; Zhang, Zihe; Yao, Sai; Chen, An; Zhao, Xudong; Zhou, Zhen

2018-03-01

Due to the high cost and insufficient resource of lithium, sodium-ion batteries are widely investigated for large-scale applications. Typically, insertion-type materials possess better cyclic stability than alloy-type and conversion-type ones. Therefore, in this work, we proposed a facile and effective method to screen sodium-based layered materials based on Materials Project database as potential candidate insertion-type materials for sodium ion batteries. The obtained Na-based layered materials contains 38 kinds of space group, which reveals that the credibility of our screening approach would not be affected by the space group. Then, some important indexes of the representative materials, including the average voltage, volume change and sodium ion mobility, were further studied by means of density functional theory computations. Some materials with extremely low volume changes and Na diffusion barriers are promising candidates for sodium ion batteries. We believe that our classification algorithm could also be used to search for other alkali and multivalent ion-based layered materials, to accelerate the development of battery materials.

Ti3C2 MXene-Derived Sodium/Potassium Titanate Nanoribbons for High-Performance Sodium/Potassium Ion Batteries with Enhanced Capacities.

PubMed

Dong, Yanfeng; Wu, Zhong-Shuai; Zheng, Shuanghao; Wang, Xiaohui; Qin, Jieqiong; Wang, Sen; Shi, Xiaoyu; Bao, Xinhe

2017-05-23

Sodium and potassium ion batteries hold promise for next-generation energy storage systems due to their rich abundance and low cost, but are facing great challenges in optimum electrode materials for actual applications. Here, ultrathin nanoribbons of sodium titanate (M-NTO, NaTi 1.5 O 8.3 ) and potassium titanate (M-KTO, K 2 Ti 4 O 9 ) were successfully synthesized by a simultaneous oxidation and alkalization process of Ti 3 C 2 MXene. Benefiting from the suitable interlayer spacing (0.90 nm for M-NTO, 0.93 nm for M-KTO), ultrathin thickness (<11 nm), narrow widths of nanoribbons (<60 nm), and open macroporous structures for enhanced ion insertion/extraction kinetics, the resulting M-NTO exhibited a large reversible capacity of 191 mAh g -1 at 200 mA g -1 for sodium storage, higher than those of pristine Ti 3 C 2 (178 mAh g -1 ) and commercial TiC derivatives (86 mAh g -1 ). Notably, M-KTO displayed a superior reversible capacity of 151 mAh g -1 at 50 mA g -1 and 88 mAh g -1 at a high rate of 300 mA g -1 and long-term stable cyclability over 900 times, which outperforms other Ti-based layered materials reported to date. Moreover, this strategy is facile and highly flexible and can be extended for preparing a large number of MXene-derived materials, from the 60+ group of MAX phases, for various applications such as supercapacitors, batteries, and electrocatalysts.

Simulated Waste Testing Of Glycolate Impacts On The 2H-Evaporator System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Martino, C. J.

2013-08-13

Glycolic acid is being studied as a total or partial replacement for formic acid in the Defense Waste Processing Facility (DWPF) feed preparation process. After implementation, the recycle stream from DWPF back to the high-level waste tank farm will contain soluble sodium glycolate. Most of the potential impacts of glycolate in the tank farm were addressed via a literature review, but several outstanding issues remained. This report documents the non-radioactive simulant tests impacts of glycolate on storage and evaporation of Savannah River Site high-level waste. The testing for which non-radioactive simulants could be used involved the following: the partitioning ofmore » glycolate into the evaporator condensate, the impacts of glycolate on metal solubility, and the impacts of glycolate on the formation and dissolution of sodium aluminosilicate scale within the evaporator. The following are among the conclusions from this work: Evaporator condensate did not contain appreciable amounts of glycolate anion. Of all tests, the highest glycolate concentration in the evaporator condensate was 0.38 mg/L. A significant portion of the tests had glycolate concentration in the condensate at less than the limit of quantification (0.1 mg/L). At ambient conditions, evaporator testing did not show significant effects of glycolate on the soluble components in the evaporator concentrates. Testing with sodalite solids and silicon containing solutions did not show significant effects of glycolate on sodium aluminosilicate formation or dissolution.« less

Facile Determination of Sodium Ion and Osmolarity in Artificial Tears by Sequential DNAzymes.

PubMed

Kim, Eun Hye; Lee, Eun-Song; Lee, Dong Yun; Kim, Young-Pil

2017-12-07

Despite high relevance of tear osmolarity and eye abnormality, numerous methods for detecting tear osmolarity rely upon expensive osmometers. We report a reliable method for simply determining sodium ion-based osmolarity in artificial tears using sequential DNAzymes. When sodium ion-specific DNAzyme and peroxidase-like DNAzyme were used as a sensing and detecting probe, respectively, the concentration of Na⁺ in artificial tears could be measured by absorbance or fluorescence intensity, which was highly correlated with osmolarity over the diagnostic range ( R ² > 0.98). Our approach is useful for studying eye diseases in relation to osmolarity.

Changes in the Sodium Content of Australian Processed Foods between 1980 and 2013 Using Analytical Data

PubMed Central

Zganiacz, Felicity; Wills, Ron B. H.; Mukhopadhyay, Soumi Paul; Arcot, Jayashree; Greenfield, Heather

2017-01-01

The objective of this study was to obtain analytical data on the sodium content of a range of processed foods and compare the levels obtained with their label claims and with published data of the same or equivalent processed foods in the 1980s and 1990s to investigate the extent of any change in sodium content in relation to reformulation targets. The sodium contents of 130 Australian processed foods were obtained by inductively coupled plasma optical emission spectrometry (ICP-OES) analysis and compared with previously published data. The sodium content between 1980 and 2013 across all products and by each product category were compared. There was a significant overall sodium reduction of 23%, 181 mg/100 g (p <0.001, 95% CI (Confidence Interval), 90 to 272 mg/100 g), in Australian processed foods since 1980, with a 12% (83 mg/100 g) reduction over the last 18 years. The sodium content of convenience foods (p < 0.001, 95% CI, 94 to 291 mg/100 g) and snack foods (p = 0.017, 95% CI, 44 to 398 mg/100 g) had declined significantly since 1980. Meanwhile, the sodium contents of processed meats (p = 0.655, 95% CI, −121 to 190) and bread and other bakery products (p = 0.115, 95% CI, −22 to 192) had decreased, though not significantly. Conversely, the sodium content of cheese (p = 0.781, 95% CI, −484 to 369 mg/100 g) had increased but also not significantly. Of the 130 products analysed, 62% met Australian reformulation targets. Sodium contents of the processed foods and the overall changes in comparison with previous data indicate a decrease over the 33 years period and suggest that the Australian recommended reformulation targets have been effective. Further sodium reduction of processed foods is still required and continuous monitoring of the reduction of sodium levels in processed foods is needed. PMID:28505147

Changes in the Sodium Content of Australian Processed Foods between 1980 and 2013 Using Analytical Data.

PubMed

Zganiacz, Felicity; Wills, Ron B H; Mukhopadhyay, Soumi Paul; Arcot, Jayashree; Greenfield, Heather

2017-05-15

The objective of this study was to obtain analytical data on the sodium content of a range of processed foods and compare the levels obtained with their label claims and with published data of the same or equivalent processed foods in the 1980s and 1990s to investigate the extent of any change in sodium content in relation to reformulation targets. The sodium contents of 130 Australian processed foods were obtained by inductively coupled plasma optical emission spectrometry (ICP-OES) analysis and compared with previously published data. The sodium content between 1980 and 2013 across all products and by each product category were compared. There was a significant overall sodium reduction of 23%, 181 mg/100 g ( p <0.001, 95% CI (Confidence Interval), 90 to 272 mg/100 g), in Australian processed foods since 1980, with a 12% (83 mg/100 g) reduction over the last 18 years. The sodium content of convenience foods ( p < 0.001, 95% CI, 94 to 291 mg/100 g) and snack foods ( p = 0.017, 95% CI, 44 to 398 mg/100 g) had declined significantly since 1980. Meanwhile, the sodium contents of processed meats ( p = 0.655, 95% CI, -121 to 190) and bread and other bakery products ( p = 0.115, 95% CI, -22 to 192) had decreased, though not significantly. Conversely, the sodium content of cheese ( p = 0.781, 95% CI, -484 to 369 mg/100 g) had increased but also not significantly. Of the 130 products analysed, 62% met Australian reformulation targets. Sodium contents of the processed foods and the overall changes in comparison with previous data indicate a decrease over the 33 years period and suggest that the Australian recommended reformulation targets have been effective. Further sodium reduction of processed foods is still required and continuous monitoring of the reduction of sodium levels in processed foods is needed.

Changes in sodium levels in processed and restaurant foods, 2005 to 2011.

PubMed

Jacobson, Michael F; Havas, Stephen; McCarter, Robert

2013-07-22

Excess consumption of sodium is an important cause of hypertension, a major risk factor for heart disease and stroke. The higher the level of consumption, the greater is a person's likelihood of developing hypertension. Numerous organizations have recommended reductions in sodium intake in the United States. Roughly 80% of the sodium consumed by Americans has been added by food manufacturers and restaurants. To compare the mean (SD) levels of sodium for identical products ascertained in 2005, 2008, and 2011. Comparison study in an academic research setting. Center for Science in the Public Interest staff have monitored sodium levels in selected processed foods and fast-food restaurant foods for many years. The sodium content in identical foods, as measured in 2005, 2008, and 2011. Between 2005 and 2011, the sodium content in 402 processed foods declined by approximately 3.5%, while the sodium content in 78 fast-food restaurant products increased by 2.6%. Although some products showed decreases of at least 30%, a greater number of products showed increases of at least 30%. The predominant finding is the absence of any appreciable or statistically significant changes in sodium content during 6 years. Based on our sample, reductions in sodium levels in processed and restaurant foods are inconsistent and slow. These findings are in accord with other data indicating the slow pace of voluntary reductions in sodium levels in processed and restaurant foods. Stronger action (eg, phased-in limits on sodium levels set by the federal government) is needed to lower sodium levels and reduce the prevalence of hypertension and cardiovascular diseases.

Lead recovery from waste CRT funnel glass by high-temperature melting process.

PubMed

Hu, Biao; Hui, Wenlong

2018-02-05

In this research, a novel and effective process for waste CRT funnel glass treatment was developed. The key to this process is removal of lead from the CRT funnel glass by high-temperature melting process. Sodium carbonate powder was used as a fusion agent, sodium sulfide serves as a catalytic agent and carbon powder acts as reducing agent. Experimental results showed that lead recovery rate increased with an increase in the amount of added sodium carbonate, sodium sulfide, carbonate, temperature and holding time initially, and then reached a stable value. The maximum lead recovery rate was approximately 94%, when the optimum adding amount of sodium carbonate, sodium sulfide, carbonate, temperature and holding time were 25%, 8%, 3.6%, 1200°C and 120min, respectively. In the high-temperature melting process, lead silicate in the funnel glass was firstly reduced, and then removed. The glass slag can be made into sodium and potassium silicate by hydrolysis process. This study proposed a practical and economical process for recovery of lead and utilization of waste glass slag. Copyright © 2017 Elsevier B.V. All rights reserved.

Evaluating management-induced soil salinization in golf courses in semi-arid landscapes

NASA Astrophysics Data System (ADS)

Young, J.; Udeigwe, T. K.; Weindorf, D. C.; Kandakji, T.; Gautam, P.; Mahmoud, M. M. A.

2015-01-01

Site-specific information on land management practices are often desired to make better assertions of their environmental impacts. A study was conducted in Lubbock, TX, in the Southern High Plains of the United States, an area characterized by semi-arid climatic conditions, to (1) examine the potential management-induced alteration in soil salinity indicators in golf course facilities and (2) develop predictive relationships for a more rapid soil salinity examination within these urban landscape soils using findings from portable x-ray fluorescence (PXRF) spectrometer. Soil samples were collected from the managed (well irrigated) and non-managed (non irrigated) areas of seven golf course facilities at 0-10, 10-20, and 20-30 cm depths, and analyzed for a suite of chemical properties. Among the extractable cations, sodium (Na) was significantly (p < 0.05) higher in the managed zones of all the golf facilities. Soil electrical conductivity (EC), exchangeable sodium percentage (ESP), and sodium adsorption ratio (SAR), parameters often used in characterizing soil salinity and sodicity, were in most part significantly (p < 0.05) higher in the managed areas. Water quality report collected over a 22-year period (1991-2013, all years not available) indicated a gradual increase in pH, EC, SAR, total alkalinity, and extractable ions, thus, supporting the former findings. Findings from the PXRF suggested possible differences in chemical species and sources that contribute to salinity between the managed and non-managed zones. PXRF quantified Cl and S, and to a lesser extent Ca, individually and collectively explained 23-85% of the variability associated with soil salinity at these facilities.

Evaluating management-induced soil salinization in golf courses in semi-arid landscapes

NASA Astrophysics Data System (ADS)

Young, J.; Udeigwe, T. K.; Weindorf, D. C.; Kandakji, T.; Gautam, P.; Mahmoud, M. A.

2015-04-01

Site-specific information on land management practices are often desired to make better assessments of their environmental impacts. A study was conducted in Lubbock, Texas, in the Southern High Plains of the United States, an area characterized by semi-arid climatic conditions, to (1) examine the potential management-induced alterations in soil salinity indicators in golf course facilities and (2) develop predictive relationships for a more rapid soil salinity examination within these urban landscape soils using findings from a portable X-ray fluorescence (PXRF) spectrometer. Soil samples were collected from managed (well irrigated) and non-managed (non-irrigated) areas of seven golf course facilities at 0-10, 10-20, and 20-30 cm depths and analyzed for a suite of chemical properties. Among the extractable cations, sodium (Na) was significantly (p < 0.05) higher in the managed zones of all the golf facilities. Soil electrical conductivity (EC), exchangeable sodium percentage (ESP), and sodium adsorption ratio (SAR), parameters often used in characterizing soil salinity and sodicity, were for the most part significantly (p < 0.05) higher in the managed areas. Water quality reports collected over a 22-year period (1991-2013, all years not available) indicated a gradual increase in pH, EC, SAR, total alkalinity, and extractable ions, thus supporting the former findings. Findings from the PXRF suggested possible differences in chemical species and sources that contribute to salinity between the managed and non-managed zones. PXRF-quantified Cl and S, and to a lesser extent Ca, individually and collectively explained 23-85% of the variability associated with soil salinity at these facilities.

Progress in Studying Scintillator Proportionality: Phenomenological Model

NASA Astrophysics Data System (ADS)

Bizarri, G.; Cherepy, N. J.; Choong, W. S.; Hull, G.; Moses, W. W.; Payne, S. A.; Singh, J.; Valentine, J. D.; Vasilev, A. N.; Williams, R. T.

2009-08-01

We present a model to describe the origin of non-proportional dependence of scintillator light yield on the energy of an ionizing particle. The non-proportionality is discussed in terms of energy relaxation channels and their linear and non-linear dependences on the deposited energy. In this approach, the scintillation response is described as a function of the deposited energy deposition and the kinetic rates of each relaxation channel. This mathematical framework allows both a qualitative interpretation and a quantitative fitting representation of scintillation non-proportionality response as function of kinetic rates. This method was successfully applied to thallium doped sodium iodide measured with SLYNCI, a new facility using the Compton coincidence technique. Finally, attention is given to the physical meaning of the dominant relaxation channels, and to the potential causes responsible for the scintillation non-proportionality. We find that thallium doped sodium iodide behaves as if non-proportionality is due to competition between radiative recombinations and non-radiative Auger processes.

Enhanced dispersion of boron nitride nanosheets in aqueous media by using bile acid-based surfactants

NASA Astrophysics Data System (ADS)

Chae, Ari; Park, Soo-Jin; Min, Byunggak; In, Insik

2018-01-01

Facile noncovalent surface functionalization of hydroxylated boron nitride nanosheet (BNNS-OH) was attempted through the sonication-assisted exfoliation of h-BN in aqueous media in the presence of bile acid-based surfactants such as sodium cholic acid (SC) or sodium deoxycholic acid (SDC), resulting in SC- or SDC-BNNS-OH dispersion with high up to 2 mg ml-1 and enhanced dispersion stability due to the increased negative zeta potential. While prepared SC-BNNS-OH revealed multi-layered BNNS structures, the large lateral sizes of hundreds nanometers and clear h-BN lattice structures are very promising for the preparation and application of water-processable BNNS-based nanomaterials. It is regarded that noncovalent functionalization of BNNS-OH based on σ-π interaction between with σ-rich bile acid-based amphiphiles and π-rich BNNS is very effective to formulate multi-functional BNNS-based nanomaterials or hybrids that can be utilized in various applications where both the pristine properties of BNNS and the extra functions are simultaneously required.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Richard D. Boardman; B. H. O'Brien; N. R. Soelberg

About one million gallons of acidic, hazardous, and radioactive sodium-bearing waste are stored in stainless steel tanks at the Idaho Nuclear Technology and Engineering Center (INTEC), which is a major operating facility of the Idaho National Engineering and Environmental Laboratory. Calcination at high-temperature conditions (600 C, with alumina nitrate and calcium nitrate chemical addition to the feed) is one of four options currently being considered by the Department of Energy for treatment of the remaining tank wastes. If calcination is selected for future processing of the sodium-bearing waste, it will be necessary to install new off-gas control equipment in themore » New Waste Calcining Facility (NWCF) to comply with the Maximum Achievable Control Technology (MACT) standards for hazardous waste combustors and incinerators. This will require, as a minimum, installing a carbon bed to reduce mercury emissions from their current level of up to 7,500 to <45 {micro}g/dscm, and a staged combustor to reduce unburned kerosene fuel in the off-gas discharge to <100 ppm CO and <10 ppm hydrocarbons. The staged combustor will also reduce NOx concentrations of about 35,000 ppm by 90-95%. A pilot-plant calcination test was completed in a newly constructed 15-cm diameter calciner vessel. The pilot-plant facility was equipped with a prototype MACT off-gas control system, including a highly efficient cyclone separator and off-gas quench/venturi scrubber for particulate removal, a staged combustor for unburned hydrocarbon and NOx destruction, and a packed activated carbon bed for mercury removal and residual chloride capture. Pilot-plant testing was performed during a 50-hour system operability test January 14-16, followed by a 100-hour high-temperature calcination pilot-plant calcination run January 19-23. Two flowsheet blends were tested: a 50-hour test with an aluminum-to-alkali metal molar ratio (AAR) of 2.25, and a 50-hour test with an AAR of 1.75. Results of the testing indicate that sodium-bearing waste can be successfully calcined at 600 C with an AAR of 1.75. Unburned hydrocarbons are reduced to less than 10 ppm (7% O2, dry basis), with >90% reduction of NOx emissions. Mercury removal by the carbon bed reached 99.99%, surpassing the control efficiency needed to meet MACT emissions standards. No deleterious impacts on the carbon bed were observed during the tests. The test results imply that upgrading the NWCF calciner with a more efficient cyclone separator and the proposed MACT equipment can process the remaining tanks wastes in 3 years or less, and comply with the MACT standards.« less

[Adaptation of the (18)FDG module for the preparation of a sodium fluoride [(18)F] injection solution in agreement with the United States (USP 32) and European Pharmacopeia (PhEur 6)].

PubMed

Martínez, T; Cordero, B; Medín, S; Sánchez Salmón, A

2011-01-01

To establish an automated procedure for the preparation of sodium fluoride (18)F injection using the resources available in our laboratory for the preparation of (18)FDG and to analyze the repercussion of the conditioning column of the fluoride ion entrapment on the characteristics of the final product. The sequence of an (18)FDG synthesis module prepared so that it traps the fluoride ion from the cyclotron in ion-exchange resin diluted with 0.9% sodium chloride. The final solution was dosified and sterilized in a final vial in an automatized dispensing module. Three different column conditioning protocols within the process were tested. Quality controls were run according to USP 32 and EurPh 6, adding control of ethanol levels of residual solvent and quality controls of the solution at 8 h post-preparation. Activation of the resin cartridges with ethanol and water was the chosen procedure, with fluoride ion trapping > 95% and pH around 7. Ethanol levels were < 5.000 ppm. Quality controls at 8 h indicated that the solution was in compliance with the USP 32 and EurPh 6 specifications. This is an easy, low-cost, reliable automated method for sodium fluoride preparation in PET facilities with existing equipment for (18)FDG synthesis and quality control. Copyright © 2010 Elsevier España, S.L. y SEMNIM. All rights reserved.

Assessing the average sodium content of prepacked foods with nutrition declarations: the importance of sales data.

PubMed

Korošec, Živa; Pravst, Igor

2014-09-04

Processed foods are recognized as a major contributor to high dietary sodium intake, associated with increased risk of cardiovascular disease. Different public health actions are being introduced to reduce sodium content in processed foods and sodium intake in general. A gradual reduction of sodium content in processed foods was proposed in Slovenia, but monitoring sodium content in the food supply is essential to evaluate the progress. Our primary objective was to test a new approach for assessing the sales-weighted average sodium content of prepacked foods on the market. We show that a combination of 12-month food sales data provided by food retailers covering the majority of the national market and a comprehensive food composition database compiled using food labelling data represent a robust and cost-effective approach to assessing the sales-weighted average sodium content of prepacked foods. Food categories with the highest sodium content were processed meats (particularly dry cured meat), ready meals (especially frozen pizza) and cheese. The reported results show that in most investigated food categories, market leaders in the Slovenian market have lower sodium contents than the category average. The proposed method represents an excellent tool for monitoring sodium content in the food supply.

Assessing the Average Sodium Content of Prepacked Foods with Nutrition Declarations: The Importance of Sales Data

PubMed Central

Korošec, Živa; Pravst, Igor

2014-01-01

Processed foods are recognized as a major contributor to high dietary sodium intake, associated with increased risk of cardiovascular disease. Different public health actions are being introduced to reduce sodium content in processed foods and sodium intake in general. A gradual reduction of sodium content in processed foods was proposed in Slovenia, but monitoring sodium content in the food supply is essential to evaluate the progress. Our primary objective was to test a new approach for assessing the sales-weighted average sodium content of prepacked foods on the market. We show that a combination of 12-month food sales data provided by food retailers covering the majority of the national market and a comprehensive food composition database compiled using food labelling data represent a robust and cost-effective approach to assessing the sales-weighted average sodium content of prepacked foods. Food categories with the highest sodium content were processed meats (particularly dry cured meat), ready meals (especially frozen pizza) and cheese. The reported results show that in most investigated food categories, market leaders in the Slovenian market have lower sodium contents than the category average. The proposed method represents an excellent tool for monitoring sodium content in the food supply. PMID:25192028

Cementitious waste option scoping study report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, A.E.; Taylor, D.D.

1998-02-01

A Settlement Agreement between the Department of Energy (DOE) and the State of Idaho mandates that all high-level radioactive waste (HLW) now stored at the Idaho Chemical Processing Plant (ICPP) on the Idaho National Engineering and Environmental Laboratory (INEEL) will be treated so that it is ready to be moved out of Idaho for disposal by a target date of 2035. This study investigates the nonseparations Cementitious Waste Option (CWO) as a means to achieve this goal. Under this option all liquid sodium-bearing waste (SBW) and existing HLW calcine would be recalcined with sucrose, grouted, canisterized, and interim stored asmore » a mixed-HLW for eventual preparation and shipment off-Site for disposal. The CWO waste would be transported to a Greater Confinement Disposal Facility (GCDF) located in the southwestern desert of the US on the Nevada Test Site (NTS). All transport preparation, shipment, and disposal facility activities are beyond the scope of this study. CWO waste processing, packaging, and interim storage would occur over a 5-year period between 2013 and 2017. Waste transport and disposal would occur during the same time period.« less

Sodium content of processed foods in the United Kingdom: analysis of 44,000 foods purchased by 21,000 households123

PubMed Central

Capelin, Cathy; Dunford, Elizabeth K; Webster, Jacqueline L; Neal, Bruce C; Jebb, Susan A

2011-01-01

Background: In the United Kingdom, sodium reduction targets have been set for a large number of processed food categories. Assessment and monitoring are essential to evaluate progress. Objectives: Our aim was to determine whether household consumer panel food-purchasing data could be used to assess the sodium content of processed foods. Our further objectives were to estimate the mean sodium content of UK foods by category and undertake analyses weighted by food-purchasing volumes. Design: Data were obtained for 21,108 British households between October 2008 and September 2009. Purchasing data (product description, product weight, annual purchases) and sodium values (mg/100 g) were collated for all food categories known to be major contributors to sodium intake. Unweighted and weighted mean sodium values were calculated. Results: Data were available for 44,372 food products. The largest contributors to sodium purchases were table salt (23%), processed meat (18%), bread and bakery products (13%), dairy products (12%), and sauces and spreads (11%). More than one-third of sodium purchased (37%) was accounted for by 5 food categories: bacon, bread, milk, cheese, and sauces. For some food groups (bread and bakery, cereals and cereal products, processed meat), purchase-weighted means were 18–35% higher than unweighted means, suggesting that market leaders have higher sodium contents than the category mean. Conclusion: The targeting of sodium reduction in a small number of food categories and focusing on products sold in the highest volumes could lead to large decreases in sodium available for consumption and therefore to gains in public health. PMID:21191142

Sodium content of processed foods in the United Kingdom: analysis of 44,000 foods purchased by 21,000 households.

PubMed

Ni Mhurchu, Cliona; Capelin, Cathy; Dunford, Elizabeth K; Webster, Jacqueline L; Neal, Bruce C; Jebb, Susan A

2011-03-01

In the United Kingdom, sodium reduction targets have been set for a large number of processed food categories. Assessment and monitoring are essential to evaluate progress. Our aim was to determine whether household consumer panel food-purchasing data could be used to assess the sodium content of processed foods. Our further objectives were to estimate the mean sodium content of UK foods by category and undertake analyses weighted by food-purchasing volumes. Data were obtained for 21,108 British households between October 2008 and September 2009. Purchasing data (product description, product weight, annual purchases) and sodium values (mg/100 g) were collated for all food categories known to be major contributors to sodium intake. Unweighted and weighted mean sodium values were calculated. Data were available for 44,372 food products. The largest contributors to sodium purchases were table salt (23%), processed meat (18%), bread and bakery products (13%), dairy products (12%), and sauces and spreads (11%). More than one-third of sodium purchased (37%) was accounted for by 5 food categories: bacon, bread, milk, cheese, and sauces. For some food groups (bread and bakery, cereals and cereal products, processed meat), purchase-weighted means were 18-35% higher than unweighted means, suggesting that market leaders have higher sodium contents than the category mean. The targeting of sodium reduction in a small number of food categories and focusing on products sold in the highest volumes could lead to large decreases in sodium available for consumption and therefore to gains in public health.

Monitoring sodium in commercially processed foods from stores and restaurants

USDA-ARS?s Scientific Manuscript database

Most of the sodium we eat comes from commercially processed foods from stores and restaurants. Sodium reduction in these foods is a key component of several recent public health efforts. Agricultural Research Service (ARS) of USDA, CDC and FDA have launched a collaborative program to monitor sodium ...

CDC Vital Signs: Where's the Sodium?

MedlinePlus

... comes from processed foods and foods prepared in restaurants. Sodium is already part of processed foods and cannot be removed. However, manufacturers and restaurants can produce foods with less sodium. In addition, ...

The biopsychology of salt hunger and sodium deficiency

PubMed Central

Hurley, Seth W.; Johnson, Alan Kim

2015-01-01

Sodium is a necessary dietary macromineral that tended to be sparsely distributed in mankind’s environment in the past. Evolutionary selection pressure shaped physiological mechanisms including hormonal systems and neural circuits that serve to promote sodium ingestion. Sodium deficiency triggers the activation of these hormonal systems and neural circuits to engage motivational processes that elicit a craving for salty substances and a state of reward when salty foods are consumed. Sodium deficiency also appears to be associated with aversive psychological states including anhedonia, impaired cognition, and fatigue. Under certain circumstances the psychological processes that promote salt intake can become powerful enough to cause “salt gluttony,” or salt intake far in excess of physiological need. The present review discusses three aspects of the biopsychology of salt hunger and sodium deficiency: 1) the psychological processes that promote salt intake during sodium deficiency, 2) the effects of sodium deficiency on mood and cognition, and 3) the sensitization of sodium appetite as a possible cause of salt gluttony. PMID:25572931

Technical Information on the Carbonation of the EBR-II Reactor, Summary Report Part 2: Application to EBR-II Primary Sodium System and Related Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Steven R. Sherman; Collin J. Knight

Residual sodium is defined as sodium metal that remains behind in pipes, vessels, and tanks after the bulk sodium metal has been melted and drained from such components. The residual sodium has the same chemical properties as bulk sodium, and differs from bulk sodium only in the thickness of the sodium deposit. Typically, sodium is considered residual when the thickness of the deposit is less than 5-6 cm. This residual sodium must be removed or deactivated when a pipe, vessel, system, or entire reactor is permanently taken out of service, in order to make the component or system safer and/ormore » to comply with decontamination and decomissioning regulations. As an alternative to the established residual sodium deactivation techniques (steam-and-nitrogen, wet vapor nitrogen, etc.), a technique involving the use of moisture and carbon dioxide has been developed. With this technique, sodium metal is converted into sodium bicarbonate by reacting it with humid carbon dioxide. Hydrogen is emitted as a by-product. This technique was first developed in the laboratory by exposing sodium samples to humidifed carbon dioxide under controlled conditions, and then demonstrated on a larger scale by treating residual sodium within the Experimental Breeder Reactor II (EBR-II) secondary cooling system, followed by the primary cooling system, respectively. The EBR-II facility is located at the Idaho National Laboratory (INL) in southeastern Idaho, USA. This report is Part 2 of a two-part report. This second report provides a supplement to the first report and describes the application of the humdidified carbon dioxide technique ("carbonation") to the EBR-II primary tank, primary cover gas systems, and the intermediate heat exchanger. Future treatment plans are also provided.« less

Sodium chloride-catalyzed oxidation of multiwalled carbon nanotubes for environmental benefit.

PubMed

Endo, Morinobu; Takeuchi, Kenji; Tajiri, Takeyuki; Park, Ki Chul; Wang, Feng; Kim, Yoong-Ahm; Hayashi, Takuya; Terrones, Mauricio; Dresselhaus, Mildred S

2006-06-22

A sodium chloride (NaCl) catalyst (0.1 w/w %) lowers the oxidation temperature of graphitized multiwalled carbon nanotubes: MWCNT-20 (diameter: 20-70 nm) and MWCNT-80 (diameter: 80-150 nm). The analysis of the reaction kinetics indicates that the oxidation of MWCNT-20 and MWCNT-80 mixed with no NaCl exhibits single reaction processes with activation energies of E(a) = 159 and 152 kJ mol(-1), respectively. The oxidation reaction in the presence of NaCl is shown to consist of two different reaction processes, that is, a first reaction and a second reaction process. The first reaction process is dominant at a low temperature of around 600 degrees C, while the second reaction process becomes more dominant than the first one in a higher temperature region. The activation energies of the first reaction processes (MWCNT-20: E(a1) = 35.7 kJ mol(-1); MWCNT-80: E(a1) = 43.5 kJ mol(-1)) are much smaller than those of the second reaction processes (MWCNT-20: E(a2) = 170 kJ mol(-1); MWCNT-80: E(a2) = 171 kJ mol(-1)). The comparison of the kinetic parameters and the results of the spectroscopic and microscopic analyses imply that the lowering of the oxidation temperature in the presence of NaCl results from the introduction of disorder into the graphitized MWCNTs (during the first reaction process), thus increasing the facility of the oxidation reaction of the disorder-induced nanotubes (in the second reaction process). It is found that the larger nanopits and cracks on the outer graphitic layers are caused by the catalytic effect of NaCl. Therefore, the NaCl-mixed samples showed more rapid and stronger oxidation compared with that of the nonmixed samples at the same residual quantity.

Laser-sodium interaction for the polychromatic laser guide star project

NASA Astrophysics Data System (ADS)

Bellanger, Veronique; Petit, Alain D.

2002-02-01

We developed a code aimed at determining the laser parameters leading to the maximum return flux of photons at 0.33 micrometers for a polychromatic sodium Laser Guide Star. This software relies upon a full 48-level collisionless and magnetic-field-free density-matrix description of the hyperfine structure of Na and includes Doppler broadening and Zeeman degeneracy. Experimental validation of BEACON was conducted on the SILVA facilities and will also be discussed in this paper.

Sodium monitoring in commercially processed and restaurant foods.

PubMed

Ahuja, Jaspreet K C; Pehrsson, Pamela R; Haytowitz, David B; Wasswa-Kintu, Shirley; Nickle, Melissa; Showell, Bethany; Thomas, Robin; Roseland, Janet; Williams, Juhi; Khan, Mona; Nguyen, Quynhanh; Hoy, Kathy; Martin, Carrie; Rhodes, Donna; Moshfegh, Alanna; Gillespie, Cathleen; Gunn, Janelle; Merritt, Robert; Cogswell, Mary

2015-03-01

Most sodium in the US diet comes from commercially processed and restaurant foods. Sodium reduction in these foods is key to several recent public health efforts. The objective was to provide an overview of a program led by the USDA, in partnership with other government agencies, to monitor sodium contents in commercially processed and restaurant foods in the United States. We also present comparisons of nutrients generated under the program to older data. We track ∼125 commercially processed and restaurant food items ("sentinel foods") annually using information from food manufacturers and periodically by nationwide sampling and laboratory analyses. In addition, we monitor >1100 other commercially processed and restaurant food items, termed "priority-2 foods" (P2Fs) biennially by using information from food manufacturers. These foods serve as indicators for assessing changes in the sodium content of commercially processed and restaurant foods in the United States. We sampled all sentinel foods nationwide and reviewed all P2Fs in 2010-2013 to determine baseline sodium concentrations. We updated sodium values for 73 sentinel foods and 551 P2Fs in the USDA's National Nutrient Database for Standard Reference (releases 23-26). Sodium values changed by at least 10% for 43 of the sentinel foods, which, for 31 foods, including commonly consumed foods such as bread, tomato catsup, and potato chips, the newer sodium values were lower. Changes in the concentrations of related nutrients (total and saturated fat, total sugar, potassium, or dietary fiber) that were recommended by the 2010 Dietary Guidelines for Americans for reduced or increased consumption accompanied sodium reduction. The results of sodium reduction efforts, based on resampling of the sentinel foods or re-review of P2Fs, will become available beginning in 2015. This monitoring program tracks sodium reduction efforts, improves food composition databases, and strengthens national nutrition monitoring. © 2015 American Society for Nutrition.

Sodium monitoring in commercially processed and restaurant foods

PubMed Central

Ahuja, Jaspreet KC; Pehrsson, Pamela R; Haytowitz, David B; Wasswa-Kintu, Shirley; Nickle, Melissa; Showell, Bethany; Thomas, Robin; Roseland, Janet; Williams, Juhi; Khan, Mona; Nguyen, Quynhanh; Hoy, Kathy; Martin, Carrie; Rhodes, Donna; Moshfegh, Alanna; Gillespie, Cathleen; Gunn, Janelle; Merritt, Robert; Cogswell, Mary

2015-01-01

Background Most sodium in the US diet comes from commercially processed and restaurant foods. Sodium reduction in these foods is key to several recent public health efforts. Objective The objective was to provide an overview of a program led by the USDA, in partnership with other government agencies, to monitor sodium contents in commercially processed and restaurant foods in the United States. We also present comparisons of nutrients generated under the program to older data. Design We track ∼125 commercially processed and restaurant food items (“sentinel foods”) annually using information from food manufacturers and periodically by nationwide sampling and laboratory analyses. In addition, we monitor >1100 other commercially processed and restaurant food items, termed “priority-2 foods” (P2Fs) biennially by using information from food manufacturers. These foods serve as indicators for assessing changes in the sodium content of commercially processed and restaurant foods in the United States. We sampled all sentinel foods nationwide and reviewed all P2Fs in 2010–2013 to determine baseline sodium concentrations. Results We updated sodium values for 73 sentinel foods and 551 P2Fs in the USDA’s National Nutrient Database for Standard Reference (releases 23–26). Sodium values changed by at least 10% for 43 of the sentinel foods, which, for 31 foods, including commonly consumed foods such as bread, tomato catsup, and potato chips, the newer sodium values were lower. Changes in the concentrations of related nutrients (total and saturated fat, total sugar, potassium, or dietary fiber) that were recommended by the 2010 Dietary Guidelines for Americans for reduced or increased consumption accompanied sodium reduction. The results of sodium reduction efforts, based on resampling of the sentinel foods or re-review of P2Fs, will become available beginning in 2015. Conclusion This monitoring program tracks sodium reduction efforts, improves food composition databases, and strengthens national nutrition monitoring. PMID:25733648

Testing of the Defense Waste Processing Facility Cold Chemical Dissolution Method in Sludge Batch 9 Qualification

DOE Office of Scientific and Technical Information (OSTI.GOV)

Edwards, T.; Pareizs, J.; Coleman, C.

For each sludge batch that is processed in the Defense Waste Processing Facility (DWPF), the Savannah River National Laboratory (SRNL) tests the applicability of the digestion methods used by the DWPF Laboratory for elemental analysis of Sludge Receipt and Adjustment Tank (SRAT) Receipt samples and SRAT Product process control samples. DWPF SRAT samples are typically dissolved using a method referred to as the DWPF Cold Chemical or Cold Chem Method (CC), (see DWPF Procedure SW4- 15.201). Testing indicates that the CC method produced mixed results. The CC method did not result in complete dissolution of either the SRAT Receipt ormore » SRAT Product with some fine, dark solids remaining. However, elemental analyses did not reveal extreme biases for the major elements in the sludge when compared with analyses obtained following dissolution by hot aqua regia (AR) or sodium peroxide fusion (PF) methods. The CC elemental analyses agreed with the AR and PF methods well enough that it should be adequate for routine process control analyses in the DWPF after much more extensive side-by-side tests of the CC method and the PF method are performed on the first 10 SRAT cycles of the Sludge Batch 9 (SB9) campaign. The DWPF Laboratory should continue with their plans for further tests of the CC method during these 10 SRAT cycles.« less

Reducing Sodium in Foods: The Effect on Flavor

PubMed Central

Liem, Djin Gie; Miremadi, Fatemeh; Keast, Russell S. J.

2011-01-01

Sodium is an essential micronutrient and, via salt taste, appetitive. High consumption of sodium is, however, related to negative health effects such as hypertension, cardiovascular diseases and stroke. In industrialized countries, about 75% of sodium in the diet comes from manufactured foods and foods eaten away from home. Reducing sodium in processed foods will be, however, challenging due to sodium’s specific functionality in terms of flavor and associated palatability of foods (i.e., increase of saltiness, reduction of bitterness, enhancement of sweetness and other congruent flavors). The current review discusses the sensory role of sodium in food, determinants of salt taste perception and a variety of strategies, such as sodium replacers (i.e., potassium salts) and gradual reduction of sodium, to decrease sodium in processed foods while maintaining palatability. PMID:22254117

Water-quality characteristics and trends for selected sites at and near the Idaho National Laboratory, Idaho, 1949-2009

USGS Publications Warehouse

Bartholomay, Roy C.; Davis, Linda C.; Fisher, Jason C.; Tucker, Betty J.; Raben, Flint A.

2012-01-01

The U.S. Geological Survey, in cooperation with the U.S. Department of Energy, analyzed water-quality data collected from 67 aquifer wells and 7 surface-water sites at the Idaho National Laboratory (INL) from 1949 through 2009. The data analyzed included major cations, anions, nutrients, trace elements, and total organic carbon. The analyses were performed to examine water-quality trends that might inform future management decisions about the number of wells to sample at the INL and the type of constituents to monitor. Water-quality trends were determined using (1) the nonparametric Kendall's tau correlation coefficient, p-value, Theil-Sen slope estimator, and summary statistics for uncensored data; and (2) the Kaplan-Meier method for calculating summary statistics, Kendall's tau correlation coefficient, p-value, and Akritas-Theil-Sen slope estimator for robust linear regression for censored data. Statistical analyses for chloride concentrations indicate that groundwater influenced by Big Lost River seepage has decreasing chloride trends or, in some cases, has variable chloride concentration changes that correlate with above-average and below-average periods of recharge. Analyses of trends for chloride in water samples from four sites located along the Big Lost River indicate a decreasing trend or no trend for chloride, and chloride concentrations generally are much lower at these four sites than those in the aquifer. Above-average and below-average periods of recharge also affect concentration trends for sodium, sulfate, nitrate, and a few trace elements in several wells. Analyses of trends for constituents in water from several of the wells that is mostly regionally derived groundwater generally indicate increasing trends for chloride, sodium, sulfate, and nitrate concentrations. These increases are attributed to agricultural or other anthropogenic influences on the aquifer upgradient of the INL. Statistical trends of chemical constituents from several wells near the Naval Reactors Facility may be influenced by wastewater disposal at the facility or by anthropogenic influence from the Little Lost River basin. Groundwater samples from three wells downgradient of the Power Burst Facility area show increasing trends for chloride, nitrate, sodium, and sulfate concentrations. The increases could be caused by wastewater disposal in the Power Burst Facility area. Some groundwater samples in the southwestern part of the INL and southwest of the INL show concentration trends for chloride and sodium that may be influenced by wastewater disposal. Some of the groundwater samples have decreasing trends that could be attributed to the decreasing concentrations in the wastewater from the late 1970s to 2009. The young fraction of groundwater in many of the wells is more than 20 years old, so samples collected in the early 1990s are more representative of groundwater discharged in the 1960s and 1970s, when concentrations in wastewater were much higher. Groundwater sampled in 2009 would be representative of the lower concentrations of chloride and sodium in wastewater discharged in the late 1980s. Analyses of trends for sodium in several groundwater samples from the central and southern part of the eastern Snake River aquifer show increasing trends. In most cases, however, the sodium concentrations are less than background concentrations measured in the aquifer. Many of the wells are open to larger mixed sections of the aquifer, and the increasing trends may indicate that the long history of wastewater disposal in the central part of the INL is increasing sodium concentrations in the groundwater.

Phosphate Framework Electrode Materials for Sodium Ion Batteries

PubMed Central

Fang, Yongjin; Zhang, Jiexin; Xiao, Lifen; Ai, Xinping; Yang, Hanxi

2017-01-01

Sodium ion batteries (SIBs) have been considered as a promising alternative for the next generation of electric storage systems due to their similar electrochemistry to Li‐ion batteries and the low cost of sodium resources. Exploring appropriate electrode materials with decent electrochemical performance is the key issue for development of sodium ion batteries. Due to the high structural stability, facile reaction mechanism and rich structural diversity, phosphate framework materials have attracted increasing attention as promising electrode materials for sodium ion batteries. Herein, we review the latest advances and progresses in the exploration of phosphate framework materials especially related to single‐phosphates, pyrophosphates and mixed‐phosphates. We provide the detailed and comprehensive understanding of structure–composition–performance relationship of materials and try to show the advantages and disadvantages of the materials for use in SIBs. In addition, some new perspectives about phosphate framework materials for SIBs are also discussed. Phosphate framework materials will be a competitive and attractive choice for use as electrodes in the next‐generation of energy storage devices. PMID:28546907

Phosphate Framework Electrode Materials for Sodium Ion Batteries.

PubMed

Fang, Yongjin; Zhang, Jiexin; Xiao, Lifen; Ai, Xinping; Cao, Yuliang; Yang, Hanxi

2017-05-01

Sodium ion batteries (SIBs) have been considered as a promising alternative for the next generation of electric storage systems due to their similar electrochemistry to Li-ion batteries and the low cost of sodium resources. Exploring appropriate electrode materials with decent electrochemical performance is the key issue for development of sodium ion batteries. Due to the high structural stability, facile reaction mechanism and rich structural diversity, phosphate framework materials have attracted increasing attention as promising electrode materials for sodium ion batteries. Herein, we review the latest advances and progresses in the exploration of phosphate framework materials especially related to single-phosphates, pyrophosphates and mixed-phosphates. We provide the detailed and comprehensive understanding of structure-composition-performance relationship of materials and try to show the advantages and disadvantages of the materials for use in SIBs. In addition, some new perspectives about phosphate framework materials for SIBs are also discussed. Phosphate framework materials will be a competitive and attractive choice for use as electrodes in the next-generation of energy storage devices.

Summary of the Madison Dynamo Experiment

NASA Astrophysics Data System (ADS)

Kendrick, R. D.; Spence, E. J.; Nornberg, M. D.; Forest, C. B.

2001-10-01

A spherical dynamo experiment has been constructed at the University of Wisconsin's liquid sodium facility. The goals of the experiment are to observe and understand magnetic instabilities driven by flow shear in MHD systems, investigate MHD turbulence for magnetic Reynolds numbers of ~100, and understand the role of fluid turbulence in current generation. Magnetic field generation is possible for only specific flow geometries. We have studied and achieved simple roll flow geometries in a full scale water experiment. Results from this experiment have guided the design of the sodium experiment. The experiment consists of a 1 m diameter, spherical stainless steel vessel filled with liquid sodium at 110 Celsius. Two 100 Hp motors with impellers drive flows in the liquid sodium with flow velocities ~ 15 m/s. A gaussian grid of Hall probes on the surface of the sodium vessel measure the generated external magnetic field. Hall probe feed-thru arrays measure the internal field. Preliminary investigations include measurements of the turbulent electromotive force and excitation of magnetic eigenmodes.

Design of the Madison Dynamo Experiment

NASA Astrophysics Data System (ADS)

Kendrick, R. D.; Bayliss, R. A.; Forest, C. B.; Nornberg, M. D.; O'Connell, R.; Spence, E. J.

2003-10-01

A spherical dynamo experiment has been constructed at the University of Wisconsin's liquid sodium facility. The goals of the experiment are to observe and understand magnetic instabilities driven by flow shear in MHD systems, investigate MHD turbulence for magnetic Reynolds numbers of ˜100, and understand the role of fluid turbulence in current generation. Magnetic field generation is possible for only specific flow geometries. We have studied and achieved simple roll flow geometries in a full scale water experiment. Results from this experiment have guided the design of the sodium experiment. The experiment consists of a 1 m diameter, spherical stainless steel vessel filled with liquid sodium at 110 Celsius. Two 100 Hp motors with impellers drive flows in the liquid sodium with flow velocities ˜ 15 m/s. A grid of Hall probes on the surface of the sodium vessel measure the generated external magnetic field. Hall probe feed-thru arrays measure the internal field. Preliminary investigations include measurements of the turbulent electromotive force and excitation of magnetic eigenmodes.

The Sodium Content of Processed Foods in South Africa during the Introduction of Mandatory Sodium Limits.

PubMed

Peters, Sanne A E; Dunford, Elizabeth; Ware, Lisa J; Harris, Teresa; Walker, Adele; Wicks, Mariaan; van Zyl, Tertia; Swanepoel, Bianca; Charlton, Karen E; Woodward, Mark; Webster, Jacqui; Neal, Bruce

2017-04-20

In June 2016, the Republic of South Africa introduced legislation for mandatory limits for the upper sodium content permitted in a wide range of processed foods. We assessed the sodium levels of packaged foods in South Africa during the one-year period leading up to the mandatory implementation date of the legislation. Data on the nutritional composition of packaged foods was obtained from nutrition information panels on food labels through both in-store surveys and crowdsourcing by users of the HealthyFood Switch mobile phone app between June 2015 and August 2016. Summary sodium levels were calculated for 15 food categories, including the 13 categories covered by the sodium legislation. The percentage of foods that met the government's 2016 sodium limits was also calculated. 11,065 processed food items were included in the analyses; 1851 of these were subject to the sodium legislation. Overall, 67% of targeted foods had a sodium level at or below the legislated limit. Categories with the lowest percentage of foods that met legislated limits were bread (27%), potato crisps (41%), salt and vinegar flavoured snacks (42%), and raw processed sausages (45%). About half (49%) of targeted foods not meeting the legislated limits were less than 25% above the maximum sodium level. Sodium levels in two-thirds of foods covered by the South African sodium legislation were at or below the permitted upper levels at the mandatory implementation date of the legislation and many more were close to the limit. The South African food industry has an excellent opportunity to rapidly meet the legislated requirements.

Core–shell PdPb@Pd aerogels with multiply-twinned intermetallic nanostructures: facile synthesis with accelerated gelation kinetics and their enhanced electrocatalytic properties

DOE PAGES

Zhu, Chengzhou; Shi, Qiurong; Fu, Shaofang; ...

2018-04-04

Delicately engineering well-defined noble metal aerogels with favorable structural and compositional features is of vital importance for wide applications. Here, we reported a one-pot and facile method for synthesizing core–shell PdPb@Pd hydrogels/aerogels with multiply-twinned grains and an ordered intermetallic phase using sodium hypophosphite as a multifunctional reducing agent. Due to the accelerated gelation kinetics induced by increased reaction temperature and the specific function of sodium hypophosphite, the formation of hydrogels can be completed within 4 h. As a result, owing to their unique porous structure and favorable geometric and electronic effects, the optimized PdPb@Pd aerogels exhibit enhanced electrochemical performance towardsmore » ethylene glycol oxidation with a mass activity of 5.8 times higher than Pd black.« less

Core–shell PdPb@Pd aerogels with multiply-twinned intermetallic nanostructures: facile synthesis with accelerated gelation kinetics and their enhanced electrocatalytic properties

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhu, Chengzhou; Shi, Qiurong; Fu, Shaofang

Delicately engineering well-defined noble metal aerogels with favorable structural and compositional features is of vital importance for wide applications. Here, we reported a one-pot and facile method for synthesizing core–shell PdPb@Pd hydrogels/aerogels with multiply-twinned grains and an ordered intermetallic phase using sodium hypophosphite as a multifunctional reducing agent. Due to the accelerated gelation kinetics induced by increased reaction temperature and the specific function of sodium hypophosphite, the formation of hydrogels can be completed within 4 h. As a result, owing to their unique porous structure and favorable geometric and electronic effects, the optimized PdPb@Pd aerogels exhibit enhanced electrochemical performance towardsmore » ethylene glycol oxidation with a mass activity of 5.8 times higher than Pd black.« less

Decontamination and decommissioning plan for processing contaminated NaK at the INEL

DOE Office of Scientific and Technical Information (OSTI.GOV)

LaRue, D.M.; Dolenc, M.R.

1986-09-01

This decontamination and decommissioning (D D) plan describes the work elements and project management plan for processing four containers of contaminated sodium/potassium (NaK) and returning the Army Reentry Vehicle Facility Site (ARVFS) to a reusable condition. The document reflects the management plan for this project before finalizing the conceptual design and preliminary prototype tests of the reaction kinetics. As a result, the safety, environmental, and accident analyses are addressed as preliminary assessments before completion at a later date. ARVFS contains an earth-covered bunker, a cylindrical test pit and metal shed, and a cable trench connecting the two items. The bunkermore » currently stores the four containers of NaK from the meltdown of the EBR-1 Mark II core. The D D project addressed in this plan involves processing the contaminated NaK and returning the ARVFS to potential reuse after cleanup.« less

Decontamination and decommissioning plan for processing contaminated NaK at the INEL

DOE Office of Scientific and Technical Information (OSTI.GOV)

LaRue, D.M.; Dolenc, M.R.

1986-09-01

This decontamination and decommissioning (D&D) plan describes the work elements and project management plan for processing four containers of contaminated sodium/potassium (NaK) and returning the Army Reentry Vehicle Facility Site (ARVFS) to a reusable condition. The document reflects the management plan for this project before finalizing the conceptual design and preliminary prototype tests of the reaction kinetics. As a result, the safety, environmental, and accident analyses are addressed as preliminary assessments before completion at a later date. ARVFS contains an earth-covered bunker, a cylindrical test pit and metal shed, and a cable trench connecting the two items. The bunker currentlymore » stores the four containers of NaK from the meltdown of the EBR-1 Mark II core. The D&D project addressed in this plan involves processing the contaminated NaK and returning the ARVFS to potential reuse after cleanup.« less

Changes in Serving Size, Calories, and Sodium Content in Processed Foods From 2009 to 2015.

PubMed

Clapp, Jenifer E; Niederman, Sarah A; Leonard, Elizabeth; Curtis, Christine J

2018-03-15

Approximately 60% of the American diet comes from processed foods, which makes improving their nutritional quality important for Americans' health. The objective of this study was to measure changes in serving sizes, calories, and sodium in top-selling processed foods that were on the market in 2009 and 2015. We analyzed products in the top 80% of sales in the 54 processed food categories with consistent serving sizes and sales metrics that were on the market in both 2009 and 2015. Mean serving size, calories (per serving and density), sodium (per serving and density), and sales were calculated for 2,979 branded processed food products. For each stratification of calorie density and sodium density (decreased, increased, or did not change), we calculated the mean serving size, calorie density, sodium density, and sales for each year. From 2009 to 2015, we found decreases in serving size (-2.3%, P < .001), calories per serving (-2.0%, P < .001), calorie density (-1.1%, P < .001), sodium per serving (-7.6%, P < .001), and sodium density (-6.0%, P < .001). A decrease in calorie density did not correspond to an increase in sodium density or vice versa. A decline in sales was observed regardless of whether calorie density or sodium density decreased, increased, or did not change. Reductions in calorie and sodium density occurred in tandem, suggesting that manufacturers reformulated for more than one health goal at the same time. Instead of unintended negative consequences of encouraging companies to reformulate for one nutrient, an overall net nutritional benefit occurred.

Effect of Agitation in Alkalization Process on the Characteristics of Sodium Carboxymethyl Sago and Cassava Starches

NASA Astrophysics Data System (ADS)

Titi, C. S.; Fachrudin, R.; Ruriani, E.; Yuliasih, I.

2018-05-01

Sodium carboxymethyl starch (Sodium CMS) is a modified starch prepared by two successive processes, alkalization and etherification. Alkalization will change the activated hydroxyl group of starch to more reactive alkoxide (St-O-), and then carboxymethyl group will substitute the hydroxyl group into sodium CMS. This research investigated the effect of agitation (1000 rpm of stirring and 4000 rpm of homogenization) in alkalization process to the modification of native starch into sodium CMS. Cassava and sago starches were mixed with sodium hydroxide (1.8 and 1.9 moles per mole anhydrous glucose units). The combination of NaOH and homogenizing gave the highest degrees of substitution for cassava (DS 0.73) and sago (DS 0.55) starches. The sodium CMS characteristics (paste clarity, water and oil absorption capacities, solubility, swelling power) were a function of mixing method but not on the amount of NaOH used.

Irradiation data for the MFA-1 and MFA-2 tests in the FFTF

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nelson, J.V.

This report provides key information on the irradiation environment of the MONJU fuel tests MFA-1 and MFA-2 in the Fast Flux Test Facility (FFTF). This information includes the fission powers, neutron fluxes, sodium temperatures and sodium flow rates in MFA-I, MFA-2 and adjacent assemblies. It also includes MFA-1 and MFA-2 compositions as a function of exposure. The work was performed at the request of Power Reactor and Nuclear Fuels Corporation (PNC) of Japan.

Tailored Granular Activated Carbon Treatment of Perchlorate in Drinking Water. ESTCP Cost and Performance Report

DTIC Science & Technology

2011-08-01

sodium nitrate NaOCl sodium hypochlorite NAVFAC-ESC Naval Facilities Engineering Command-Engineering Service Center NDMA n-nitrosodimethylamine NL...nitrosodimethylamine ( NDMA ) was measured in effluent from the second TGAC bed at 39 ng/L. No other nitrosamines were detected in any other sampling event...was 6.3 ng/L NDMA in an effluent sample of the prechlorination/oxidant train. 6.6.3.4 General Chemistry Results With a few exceptions, values of pH

A Core Facility for the Study of Neurotoxins of Biological Origin

DTIC Science & Technology

1990-06-15

toxicity of 5 x 10-8 MLD/mg protein. Sodium 125 Iodine and the Bolton-Hunter Reagent - 1251odine were purchased from Amersham. Chloramine- T , glycine...tyrosine and all salts and buffers were from Sigma Chemical Co. and Fisher. Iodination procedures. The chloramine- T method was used essentially as...previously described. Tetanus toxin (100 ig) in sodium phosphate buffer (100 mM, pH 7.4) was mixed with chloramine- T (0.5 mM) and Na 1251 (1 mCi) for 30

MoO2 nanosheets embedded in amorphous carbon matrix for sodium-ion batteries

NASA Astrophysics Data System (ADS)

He, Hong; Man, Yuhong; Yang, Jingang; Xie, Jiale; Xu, Maowen

2017-10-01

MoO2 nanosheets embedded in the amorphous carbon matrix (MoO2/C) are successfully synthesized via a facile hydrothermal method and investigated as an anode for sodium-ion batteries. Because of the efficient ion transport channels and good volume change accommodation, MoO2/C delivers a discharge/charge capacity of 367.8/367.0 mAh g-1 with high coulombic efficiency (99.4%) after 100 cycles at a current density of 50 mA g-1.

Sodium modified molybdenum sulfide via molten salt electrolysis as an anode material for high performance sodium-ion batteries.

PubMed

Wang, Shuai; Tu, Jiguo; Yuan, Yan; Ma, Rui; Jiao, Shuqiang

2016-01-28

The paper reports a facile and cost effective method for fabricating sodium molybdenum sulfide nanoparticles through using MoS2 sheets as the precursor by sodium-modification. The electrochemical performances of sodium molybdenum sulfide nanoparticles are studied as anode materials for sodium-ion batteries. The galvanostatic charge-discharge measurements have been performed in a voltage range of 0.01-2.6 V vs. Na(+)/Na under different current densities, using the as-prepared sodium molybdenum sulfide nanoparticles as a working electrode. Typically, the initial discharge and charge capacities of sodium molybdenum sulfide nanoparticles are 475 and 380 mA h g(-1), respectively, at a current density of 20 mA g(-1). The sodium molybdenum sulfide nanoparticles exhibit high capacity with a reversible discharge capacity of about 190 mA h g(-1) after 100 cycles. It should be emphasized that the discharge reaction consists of two steps which correspond to voltage plateaus of 0.93 V and 0.85 V vs. Na(+)/Na in the first discharge curve of the Na/MoS2 battery, respectively. But there is only one apparent voltage plateau in the Na/Na-Mo-S battery, and it reduces to below 0.5 V vs. Na(+)/Na, which can enhance the power density. All of the findings demonstrate that sodium molybdenum sulfide nanoparticles have steady cycling performance and environmental and cost friendliness as next generation secondary batteries.

40 CFR 436.150 - Applicability; description of the sodium sulfate subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... sodium sulfate subcategory. 436.150 Section 436.150 Protection of Environment ENVIRONMENTAL PROTECTION... SOURCE CATEGORY Sodium Sulfate Subcategory § 436.150 Applicability; description of the sodium sulfate subcategory. The provisions of this subpart are applicable to the processing of sodium sulfate. Sodium sulfate...

40 CFR 436.150 - Applicability; description of the sodium sulfate subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... sodium sulfate subcategory. 436.150 Section 436.150 Protection of Environment ENVIRONMENTAL PROTECTION... Sodium Sulfate Subcategory § 436.150 Applicability; description of the sodium sulfate subcategory. The provisions of this subpart are applicable to the processing of sodium sulfate. Sodium sulfate obtained from...

40 CFR 436.150 - Applicability; description of the sodium sulfate subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... sodium sulfate subcategory. 436.150 Section 436.150 Protection of Environment ENVIRONMENTAL PROTECTION... SOURCE CATEGORY Sodium Sulfate Subcategory § 436.150 Applicability; description of the sodium sulfate subcategory. The provisions of this subpart are applicable to the processing of sodium sulfate. Sodium sulfate...

40 CFR 436.150 - Applicability; description of the sodium sulfate subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... sodium sulfate subcategory. 436.150 Section 436.150 Protection of Environment ENVIRONMENTAL PROTECTION... SOURCE CATEGORY Sodium Sulfate Subcategory § 436.150 Applicability; description of the sodium sulfate subcategory. The provisions of this subpart are applicable to the processing of sodium sulfate. Sodium sulfate...

40 CFR 436.150 - Applicability; description of the sodium sulfate subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... sodium sulfate subcategory. 436.150 Section 436.150 Protection of Environment ENVIRONMENTAL PROTECTION... Sodium Sulfate Subcategory § 436.150 Applicability; description of the sodium sulfate subcategory. The provisions of this subpart are applicable to the processing of sodium sulfate. Sodium sulfate obtained from...

Comparison of lead removal behaviors and generation of water-soluble sodium compounds in molten lead glass under a reductive atmosphere

NASA Astrophysics Data System (ADS)

Okada, Takashi; Nishimura, Fumihiro; Xu, Zhanglian; Yonezawa, Susumu

2018-06-01

We propose a method of reduction-melting at 1000 °C, using a sodium-based flux, to recover lead from cathode-ray tube funnel glass. To recover the added sodium from the treated glass, we combined a reduction-melting process with a subsequent annealing step at 700 °C, generating water-soluble sodium compounds in the molten glass. Using this combined process, this study compares lead removal behavior and the generation of water-soluble sodium compounds (sodium silicates and carbonates) in order to gain fundamental information to enhance the recovery of both lead and sodium. We find that lead removal increases with increasing melting time, whereas the generation efficiency of water-soluble sodium increases and decreases periodically. In particular, near 90% lead removal, the generation of water-soluble sodium compounds decreased sharply, increasing again with the prolongation of melting time. This is due to the different crystallization and phase separation efficiencies of water-soluble sodium in molten glass, whose structure continuously changes with lead removal. Previous studies used a melting time of 60 min in the processes. However, in this study, we observe that a melting time of 180 min enhances the water-soluble sodium generation efficiency.

Caustic Recycling Pilot Unit to Separate Sodium from LLW at Hanford Site - 12279

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pendleton, Justin; Bhavaraju, Sai; Priday, George

As part of the Department of Energy (DOE) sponsored Advanced Remediation Technologies initiative, a scheme was developed to combine Continuous Sludge Leaching (CSL), Near-Tank Cesium Removal (NTCR), and Caustic Recycling Unit (CRU) using Ceramatec technology, into a single system known as the Pilot Near-Tank Treatment System (PNTTS). The Cesium (Cs) decontaminated effluent from the NTCR process will be sent to the caustic recycle process for recovery of the caustic which will be reused in another cycle of caustic leaching in the CSL process. Such an integrated mobile technology demonstration will give DOE the option to insert this process for sodiummore » management at various sites in Hanford, and will minimize the addition of further sodium into the waste tanks. This allows for recycling of the caustic used to remove aluminum during sludge washing as a pretreatment step in the vitrification of radioactive waste which will decrease the Low Level Waste (LLW) volume by as much as 39%. The CRU pilot process was designed to recycle sodium in the form of pure sodium hydroxide. The basis for the design of the 1/4 scale pilot caustic recycling unit was to demonstrate the efficient operation of a larger scale system to recycle caustic from the NTCR effluent stream from the Parsons process. The CRU was designed to process 0.28 liter/minute of NTCR effluent, and generate 10 M concentration of 'usable' sodium hydroxide. The proposed process operates at 40 deg. C to provide additional aluminum solubility and then recover the sodium hydroxide to the point where the aluminum is saturated at 40 deg. C. A system was developed to safely separate and vent the gases generated during operation of the CRU with the production of 10 M sodium hydroxide. Caustic was produced at a rate between 1.9 to 9.3 kg/hr. The CRU was located inside an ISO container to allow for moving of the unit close to tank locations to process the LLW stream. Actual tests were conducted with the NTCR effluent simulant from the Parsons process in the CRU. The modular CRU is easily scalable as a standalone system for caustic recycling, or for NTTS integration or for use as an In-Tank Treatment System to process sodium bearing waste to meet LLW processing needs at the Hanford site. The standalone pilot operation of the CRU to recycle sodium from NTCR effluent places the technology demonstration at TRL level 6. Multiple operations were performed with the CRU to process up to 500 gallons of the NTCR effluent and demonstrate an efficient separation of up to 70 % of the sodium without solids precipitation while producing 10 M caustic. Batch mode operation was conducted to study the effects of chemistry variation, establish the processing rate, and optimize the process operating conditions to recycle caustic from the NTCR effluent. The performance of the CRU was monitored by tracking the density parameter to control the concentration of caustic produced. Different levels of sodium were separated in tests from the effluent at a fixed operating current density and temperature. The voltage of the modules remained stable during the unit operation which demonstrated steady operation to separate sodium from the NTCR effluent. The sodium transfer current efficiency was measured in testing based on the concentration of caustic produced. Measurements showed a current efficiency of 99.8% for sodium transfer from the NTCR effluent to make sodium hydroxide. The sodium and hydroxide contents of the anolyte (NTCR feed) and catholyte (caustic product) were measured before and after each batch test. In two separate batch tests, samples were taken at different levels of sodium separation and analyzed to determine the stability of the NTCR effluent after sodium separation. The stability characteristics and changes in physical and chemical properties of the NTCR effluent chemistry after separation of sodium hydroxide as a function of storage time were evaluated. Parameters such as level of precipitated alumina, total alkalinity, analysis of Al, Na, K, Cs, Fe, OH, nitrate, nitrite, total dissolved and undissolved solids, viscosity, density, and other parameters of the NTCR effluent were measured. Changes in rheology and properties of NTCR stream to support downstream handling of the effluent after sodium separation was the basis for the analysis. The results show that the NTCR effluent is stable without the precipitation of aluminum hydroxide after 70% of the sodium was separated from the effluent. (authors)« less

Unique Cobalt Sulfide/Reduced Graphene Oxide Composite as an Anode for Sodium-Ion Batteries with Superior Rate Capability and Long Cycling Stability.

PubMed

Peng, Shengjie; Han, Xiaopeng; Li, Linlin; Zhu, Zhiqiang; Cheng, Fangyi; Srinivansan, Madhavi; Adams, Stefan; Ramakrishna, Seeram

2016-03-09

Exploitation of high-performance anode materials is essential but challenging to the development of sodium-ion batteries (SIBs). Among all proposed anode materials for SIBs, sulfides have been proved promising candidates due to their unique chemical and physical properties. In this work, a facile solvothermal method to in situ decorate cobalt sulfide (CoS) nanoplates on reduced graphene oxide (rGO) to build CoS@rGO composite is described. When evaluated as anode for SIBs, an impressive high specific capacity (540 mAh g(-1) at 1 A g(-1) ), excellent rate capability (636 mAh g(-1) at 0.1 A g(-1) and 306 mAh g(-1) at 10 A g(-1)), and extraordinarily cycle stability (420 mAh g(-1) at 1 A g(-1) after 1000 cycles) have been demonstrated by CoS@rGO composite for sodium storage. The synergetic effect between the CoS nanoplates and rGO matrix contributes to the enhanced electrochemical performance of the hybrid composite. The results provide a facile approach to fabricate promising anode materials for high-performance SIBs. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Urinary Sodium and Potassium Excretion and Dietary Sources of Sodium in Maputo, Mozambique.

PubMed

Queiroz, Ana; Damasceno, Albertino; Jessen, Neusa; Novela, Célia; Moreira, Pedro; Lunet, Nuno; Padrão, Patrícia

2017-08-03

This study aimed to evaluate the urinary excretion of sodium and potassium, and to estimate the main food sources of sodium in Maputo dwellers. A cross-sectional evaluation of a sample of 100 hospital workers was conducted between October 2012 and May 2013. Sodium and potassium urinary excretion was assessed in a 24-h urine sample; creatinine excretion was used to exclude unlikely urine values. Food intake in the same period of urine collection was assessed using a 24-h dietary recall. The Food Processor Plus ® was used to estimate sodium intake corresponding to naturally occurring sodium and sodium added to processed foods (non-discretionary sodium). Salt added during culinary preparations (discretionary sodium) was computed as the difference between urinary sodium excretion and non-discretionary sodium. The mean (standard deviation) urinary sodium excretion was 4220 (1830) mg/day, and 92% of the participants were above the World Health Organization (WHO) recommendations. Discretionary sodium contributed 60.1% of total dietary sodium intake, followed by sodium from processed foods (29.0%) and naturally occurring sodium (10.9%). The mean (standard deviation) urinary potassium excretion was 1909 (778) mg/day, and 96% of the participants were below the WHO potassium intake recommendation. The mean (standard deviation) sodium to potassium molar ratio was 4.2 (2.4). Interventions to decrease sodium and increase potassium intake are needed in Mozambique.

Urinary Sodium and Potassium Excretion and Dietary Sources of Sodium in Maputo, Mozambique

PubMed Central

Queiroz, Ana; Damasceno, Albertino; Jessen, Neusa; Novela, Célia; Moreira, Pedro; Lunet, Nuno

2017-01-01

This study aimed to evaluate the urinary excretion of sodium and potassium, and to estimate the main food sources of sodium in Maputo dwellers. A cross-sectional evaluation of a sample of 100 hospital workers was conducted between October 2012 and May 2013. Sodium and potassium urinary excretion was assessed in a 24-h urine sample; creatinine excretion was used to exclude unlikely urine values. Food intake in the same period of urine collection was assessed using a 24-h dietary recall. The Food Processor Plus® was used to estimate sodium intake corresponding to naturally occurring sodium and sodium added to processed foods (non-discretionary sodium). Salt added during culinary preparations (discretionary sodium) was computed as the difference between urinary sodium excretion and non-discretionary sodium. The mean (standard deviation) urinary sodium excretion was 4220 (1830) mg/day, and 92% of the participants were above the World Health Organization (WHO) recommendations. Discretionary sodium contributed 60.1% of total dietary sodium intake, followed by sodium from processed foods (29.0%) and naturally occurring sodium (10.9%). The mean (standard deviation) urinary potassium excretion was 1909 (778) mg/day, and 96% of the participants were below the WHO potassium intake recommendation. The mean (standard deviation) sodium to potassium molar ratio was 4.2 (2.4). Interventions to decrease sodium and increase potassium intake are needed in Mozambique. PMID:28771193

The Sodium Content of Processed Foods in South Africa during the Introduction of Mandatory Sodium Limits

PubMed Central

Peters, Sanne A. E.; Dunford, Elizabeth; Ware, Lisa J.; Harris, Teresa; Walker, Adele; Wicks, Mariaan; van Zyl, Tertia; Swanepoel, Bianca; Charlton, Karen E.; Woodward, Mark; Webster, Jacqui; Neal, Bruce

2017-01-01

Background: In June 2016, the Republic of South Africa introduced legislation for mandatory limits for the upper sodium content permitted in a wide range of processed foods. We assessed the sodium levels of packaged foods in South Africa during the one-year period leading up to the mandatory implementation date of the legislation. Methods: Data on the nutritional composition of packaged foods was obtained from nutrition information panels on food labels through both in-store surveys and crowdsourcing by users of the HealthyFood Switch mobile phone app between June 2015 and August 2016. Summary sodium levels were calculated for 15 food categories, including the 13 categories covered by the sodium legislation. The percentage of foods that met the government’s 2016 sodium limits was also calculated. Results: 11,065 processed food items were included in the analyses; 1851 of these were subject to the sodium legislation. Overall, 67% of targeted foods had a sodium level at or below the legislated limit. Categories with the lowest percentage of foods that met legislated limits were bread (27%), potato crisps (41%), salt and vinegar flavoured snacks (42%), and raw processed sausages (45%). About half (49%) of targeted foods not meeting the legislated limits were less than 25% above the maximum sodium level. Conclusion: Sodium levels in two-thirds of foods covered by the South African sodium legislation were at or below the permitted upper levels at the mandatory implementation date of the legislation and many more were close to the limit. The South African food industry has an excellent opportunity to rapidly meet the legislated requirements. PMID:28425938

Changes in Average Sodium Content of Prepacked Foods in Slovenia during 2011–2015

PubMed Central

Lavriša, Živa

2017-01-01

A voluntary gradual reduction in the salt content of processed foods was proposed Slovenia in 2010. Our objective was to determine the sodium content of prepacked foods in 2015 and to compare these results with data from 2011. Labelled sodium content and 12-month sales data were collected for prepacked foods (N = 5759) from major food stores in Slovenia. The average and sales-weighted sodium content, as well as the share in total sodium sales (STSS) were calculated for different food category levels, particularly focusing on processed meat and derivatives (STSS: 13.1%; 904 mg Na/100 g), bread (9.1%; 546 mg), cheese (5.1%; 524 mg), and ready-to-eat meals (2.2%; 510 mg). Reduced sale-weighted sodium content was observed in cheese (57%), a neutral trend was observed in processed meat and derivatives (99%) and bread (100%), and an increase in sodium content was found in ready meals (112%). Similar trends were observed for average sodium levels, but the difference was significant only in the case of ready meals. No statistically significant changes were observed for the matched products, although about one-third of the matched products had been reformulated by lowering the sodium level by more than 3.8%. Additional efforts are needed to ensure salt reduction in processed foods in Slovenia. Such efforts should combine closer collaboration with the food industry, additional consumer education, and setting specific sodium content targets (limits) for key food categories. PMID:28850061

Changes in Average Sodium Content of Prepacked Foods in Slovenia during 2011-2015.

PubMed

Pravst, Igor; Lavriša, Živa; Kušar, Anita; Miklavec, Krista; Žmitek, Katja

2017-08-29

A voluntary gradual reduction in the salt content of processed foods was proposed Slovenia in 2010. Our objective was to determine the sodium content of prepacked foods in 2015 and to compare these results with data from 2011. Labelled sodium content and 12-month sales data were collected for prepacked foods ( N = 5759) from major food stores in Slovenia. The average and sales-weighted sodium content, as well as the share in total sodium sales (STSS) were calculated for different food category levels, particularly focusing on processed meat and derivatives (STSS: 13.1%; 904 mg Na/100 g), bread (9.1%; 546 mg), cheese (5.1%; 524 mg), and ready-to-eat meals (2.2%; 510 mg). Reduced sale-weighted sodium content was observed in cheese (57%), a neutral trend was observed in processed meat and derivatives (99%) and bread (100%), and an increase in sodium content was found in ready meals (112%). Similar trends were observed for average sodium levels, but the difference was significant only in the case of ready meals. No statistically significant changes were observed for the matched products, although about one-third of the matched products had been reformulated by lowering the sodium level by more than 3.8%. Additional efforts are needed to ensure salt reduction in processed foods in Slovenia. Such efforts should combine closer collaboration with the food industry, additional consumer education, and setting specific sodium content targets (limits) for key food categories.

Study design and baseline characteristics of a combined educational and environmental intervention trial to lower sodium intake in Swiss employees.

PubMed

Beer-Borst, Sigrid; Luta, Xhyljeta; Hayoz, Stefanie; Sommerhalder, Kathrin; Krause, Corinna Gréa; Eisenblätter, Julia; Jent, Sandra; Siegenthaler, Stefan; Aubert, Rafael; Haldimann, Max; Strazzullo, Pasquale

2018-04-02

Blood pressure is a primary cardiovascular disease risk factor. Population-wide governmental strategies aim to reduce lifestyle and dietary risk factors for hypertension, one of which is an unbalanced diet with high sodium and low potassium intakes. Nutrition interventions in the workplace are considered a promising approach in encouraging health-promoting behaviors. We developed and conducted the health promoting sodium reduction trial "Healthful & Tasty: Sure!" in worksites in the German-speaking part of Switzerland from May 2015 to Nov 2016, for which we present the study protocol and baseline characteristics. Healthful & Tasty, a cluster nonrandomized single-arm trial with calibration arm, aimed to demonstrate the effectiveness of a combined educational and environmental intervention in the workplace in reducing employees' average daily sodium/salt intake by 15%. To this end, health and food literacy of employees and guideline compliance among the catering facility team needed to be improved. The primary outcome measure was sodium/salt intake estimated from sodium excretion in a 24-h urine sample. Secondary outcome measures included changes in the overall qualitative diet composition, blood pressure, anthropometric indices, and health and food literacy. Of eight organizations with catering facilities, seven organizations took part in the nutrition education and catering salt reduction interventions, and one organization participated as a control. Overall, 145 consenting employees were included in the staggered, one-year four-phase trial, of which 132 participated in the intervention group. In addition to catering surveys and food sampling, the trial included five follow-up health assessments including questionnaires, blood pressure measurements, anthropometrics, and sodium, potassium, and iodine intake measurements obtained from 24-h and spot urine samples, and a food record checklist. Exploratory and hypothesis generating baseline statistical analysis included 141 participants with adequate 24-h urine samples. Despite practice-driven limitations to the study design and small cluster and participant numbers, this trial has methodological strength and will provide important insights into the effectiveness of a combined educational and environmental intervention to reduce salt intake among female and male Swiss employees. German Clinical Trials Register, DRKS00006790 . Registered 23 September 2014.

Food Sources of Sodium Intake in an Adult Mexican Population: A Sub-Analysis of the SALMEX Study

PubMed Central

Colin-Ramirez, Eloisa; Miranda-Alatriste, Paola Vanessa; Tovar-Villegas, Verónica Ivette; Arcand, JoAnne; Correa-Rotter, Ricardo

2017-01-01

Excessive dietary sodium intake increases blood pressure and cardiovascular risk. In Western diets, the majority of dietary sodium comes from packaged and prepared foods (≈75%); however, in Mexico there is no available data on the main food sources of dietary sodium. The main objective of this study was to identify and characterize the major food sources of dietary sodium in a sample of the Mexican Salt and Mexico (SALMEX) cohort. Adult male and female participants of the SALMEX study who provided a complete and valid three-day food record during the baseline visit were included. Overall, 950 participants (mean age 38.6 ± 10.7 years) were analyzed to determine the total sodium contributed by the main food sources of sodium identified. Mean daily sodium intake estimated by three-day food records and 24-h urinary sodium excretion was 2647.2 ± 976.9 mg/day and 3497.2 ± 1393.0, in the overall population, respectively. Processed meat was the main contributor to daily sodium intake, representing 8% of total sodium intake per capita as measured by three-day food records. When savory bread (8%) and sweet bakery goods (8%) were considered together as bread products, these were the major contributor to daily sodium intake, accounting for the 16% of total sodium intake, followed by processed meat (8%), natural cheeses (5%), and tacos (5%). These results highlight the need for public health policies focused on reducing the sodium content of processed food in Mexico. PMID:28749449

Implications of salt and sodium reduction on microbial food safety.

PubMed

Taormina, Peter J

2010-03-01

Excess sodium consumption has been cited as a primary cause of hypertension and cardiovascular diseases. Salt (sodium chloride) is considered the main source of sodium in the human diet, and it is estimated that processed foods and restaurant foods contribute 80% of the daily intake of sodium in most of the Western world. However, ample research demonstrates the efficacy of sodium chloride against pathogenic and spoilage microorganisms in a variety of food systems. Notable examples of the utility and necessity of sodium chloride include the inhibition of growth and toxin production by Clostridium botulinum in processed meats and cheeses. Other sodium salts contributing to the overall sodium consumption are also very important in the prevention of spoilage and/or growth of microorganisms in foods. For example, sodium lactate and sodium diacetate are widely used in conjunction with sodium chloride to prevent the growth of Listeria monocytogenes and lactic acid bacteria in ready-to-eat meats. These and other examples underscore the necessity of sodium salts, particularly sodium chloride, for the production of safe, wholesome foods. Key literature on the antimicrobial properties of sodium chloride in foods is reviewed here to address the impact of salt and sodium reduction or replacement on microbiological food safety and quality.

NASA/Air Force/Environmental Protection Agency Interagency Depainting Study

NASA Technical Reports Server (NTRS)

Clark-Ingram, Marceia

1998-01-01

Many popular and widely used paint stripping products have traditionally contained methylene chloride as their main active ingredient. However, the Environmental Protection Agency (EPA) has critically curved the allowable use of methylene chloride under the National Emission Standard for Hazardous Air Pollutants regulating Aerospace Manufacturing and Rework Facilities . Compliance with this rule was mandatory by September 1998 for affected facilities. An effort is underway to identify and evaluate alternative depainting technologies emphasizing those believed both effective and environmentally benign. On behalf of the EPA and in cooperation with the United States Air Force, the National Aeronautics and Space Administration is conducting a technical assessment of several alternative technologies ( i.e. : chemical stripping, two CO2 blasting processes, CO2 xenon lamp coating removal, CO2 Laser stripping, plastic media blasting, sodium bicarbonate wet stripping, high pressure water stripping, and wheat starch blasting). These depainting processes represent five removal method categories, namely abrasive, impact, cryogenic, thermal, and/or molecular bonding dissociation. This paper discusses the test plan and parameters for this interagency study. Several thicknesses of clad and non-clad aluminum substrates were used to prepare test specimens. Each depainting process has been assigned a specimen lot, all of which have completed three to five stripping cycles. Numerous metallurgical evaluations are underway to assess the impact of these alternative depainting processes upon the structural integrity of the substrate.

Determination of gross alpha and gross beta in soil around repository facility at Bukit Kledang, Perak, Malaysia

NASA Astrophysics Data System (ADS)

Adziz, Mohd Izwan Abdul; Siong, Khoo Kok

2018-04-01

Recently, the Long Term Storage Facility (LTSF) in Bukit Kledang, Perak, Malaysia, has been upgraded to repository facility upon the completion of decontamination and decommissioning (D&D) process. Thorium waste and contaminated material that may contain some minor amounts of thorium hydroxide were disposed in this facility. This study is conducted to determine the concentrations of gross alpha and gross beta radioactivities in soil samples collected around the repository facility. A total of 12 soil samples were collected consisting 10 samples from around the facility and 2 samples from selected residential area near the facility. In addition, the respective dose rates were measured 5 cm and 1 m above the ground by using survey meter with Geiger Muller (GM) detector and Sodium Iodide (NaI) detector. Soil samples were collected using hand auger and then were taken back to the laboratory for further analysis. Samples were cleaned, dried, pulverized and sieved prior to analysis. Gross alpha and gross beta activity measurements were carried out using gas flow proportional counter, Canberra Series 5 XLB - Automatic Low Background Alpha and Beta Counting System. The obtained results show that, the gross alpha and gross beta activity concentration ranged from 1.55 to 5.34 Bq/g with a mean value of 3.47 ± 0.09 Bq/g and 1.64 to 5.78 Bq/g with a mean value of 3.49 ± 0.09 Bq/g, respectively. These results can be used as an additional data to represent terrestrial radioactivity baseline data for Malaysia environment. This estimation will also serve as baseline for detection of any future related activities of contamination especially around the repository facility area.

Changes in Serving Size, Calories, and Sodium Content in Processed Foods From 2009 to 2015

PubMed Central

Niederman, Sarah A.; Leonard, Elizabeth; Curtis, Christine J.

2018-01-01

Introduction Approximately 60% of the American diet comes from processed foods, which makes improving their nutritional quality important for Americans’ health. The objective of this study was to measure changes in serving sizes, calories, and sodium in top-selling processed foods that were on the market in 2009 and 2015. Methods We analyzed products in the top 80% of sales in the 54 processed food categories with consistent serving sizes and sales metrics that were on the market in both 2009 and 2015. Mean serving size, calories (per serving and density), sodium (per serving and density), and sales were calculated for 2,979 branded processed food products. For each stratification of calorie density and sodium density (decreased, increased, or did not change), we calculated the mean serving size, calorie density, sodium density, and sales for each year. Results From 2009 to 2015, we found decreases in serving size (−2.3%, P < .001), calories per serving (−2.0%, P < .001), calorie density (−1.1%, P < .001), sodium per serving (−7.6%, P < .001), and sodium density (−6.0%, P < .001). A decrease in calorie density did not correspond to an increase in sodium density or vice versa. A decline in sales was observed regardless of whether calorie density or sodium density decreased, increased, or did not change. Conclusion Reductions in calorie and sodium density occurred in tandem, suggesting that manufacturers reformulated for more than one health goal at the same time. Instead of unintended negative consequences of encouraging companies to reformulate for one nutrient, an overall net nutritional benefit occurred. PMID:29543584

Dose Rate Calculation of TRU Metal Ingot in Pyroprocessing - 12202

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Yoon Hee; Lee, Kunjai

Spent fuel management has been a main problem to be solved for continuous utilization of nuclear energy. Spent fuel management policy of Korea is 'Wait and See'. It is focused on Pyro-process and SFR (Sodium-cooled Fast Reactor) for closed-fuel cycle research and development in Korea. For peaceful use of nuclear facilities, the proliferation resistance has to be proved. Proliferation resistance is one of key constraints in the deployment of advanced nuclear energy systems. Non-proliferation and safeguard issues have been strengthening internationally. Barriers to proliferation are that reduces desirability or attractiveness as an explosive and makes it difficult to gain accessmore » to the materials, or makes it difficult to misuse facilities and/or technologies for weapons applications. Barriers to proliferation are classified into intrinsic and extrinsic barriers. Intrinsic barrier is inherent quality of reactor materials or the fuel cycle that is built into the reactor design and operation such as material and technical barriers. As one of the intrinsic measures, the radiation from the material is considered significantly. Therefore the radiation of TRU metal ingot from the pyro-process was calculated using ORIGEN and MCNP code. (authors)« less

Cubic KTi2(PO4)3 as electrode materials for sodium-ion batteries.

PubMed

Han, Jin; Xu, Maowen; Niu, Yubin; Jia, Min; Liu, Ting; Li, Chang Ming

2016-12-01

A novel cubic KTi2(PO4)3 is successfully synthesized via a facile hydrothermal method combined with a subsequent annealing treatment and further used as electrode material for sodium-ion batteries for the first time. For comparison, carbon-coated KTi2(PO4)3 obtained by a normal cane sugar-assisted method reveals superior electrochemical performances in sodium-ion battery. Besides of the high coulombic efficiency of nearly 100% after 100 cycles, a stable capacity of 112mAhg(-1) can be achieved at 0.5C after 100 cycles, and still maintains to 105mAhg(-1) after 500 cycles with capacity retention of approximately 90%. Copyright © 2016 Elsevier Inc. All rights reserved.

Pipe connector

DOEpatents

Sullivan, Thomas E.; Pardini, John A.

1978-01-01

A safety test facility for testing sodium-cooled nuclear reactor components includes a reactor vessel and a heat exchanger submerged in sodium in the tank. The reactor vessel and heat exchanger are connected by an expansion/deflection pipe coupling comprising a pair of coaxially and slidably engaged tubular elements having radially enlarged opposed end portions of which at least a part is of spherical contour adapted to engage conical sockets in the ends of pipes leading out of the reactor vessel and in to the heat exchanger. A spring surrounding the pipe coupling urges the end portions apart and into engagement with the spherical sockets. Since the pipe coupling is submerged in liquid a limited amount of leakage of sodium from the pipe can be tolerated.

Relationship of nutrition knowledge and self-reported dietary behaviors with urinary excretion of sodium and potassium: comparison between dietitians and nondietitians.

PubMed

Sugimoto, Minami; Asakura, Keiko; Masayasu, Shizuko; Sasaki, Satoshi

2016-05-01

The effectiveness of better nutrition knowledge and dietary behavior on healthier dietary intake is still controversial. We hypothesized that nutritional knowledge and dietary behavior are associated with sodium and potassium intake in adult women. A cross-sectional study was conducted at welfare facilities located in 20 areas of Japan. Ninety-nine female dietitians and 117 nondietitians aged 20 to 69 years participated. Sodium and potassium intake were assessed with two 24-hour urine collections and 4-day semiweighed diet records. Nutritional knowledge and dietary behavior were accessed with 3 questionnaires. Analysis of covariance was performed to compare sodium and potassium excretion and selected nutrition and food intake between dietitians and nondietitians. After adjustment for age and smoking habit, sodium and potassium excretion did not significantly differ between the 2 groups (3857 vs 3959 mg/d, P = .57, and 2016 vs 1886 mg/d, P = .10, respectively). Sodium/potassium ratio was significantly lower in the dietitians (P = .044). The dietitians used food labels for sodium contents more often than the nondietitians and consumed more fruits and vegetables (P = .048 and P < .0001, respectively) and less sugar and confectionaries and fat and oils (P = .016 and P = .010, respectively). In conclusion, the higher level of nutritional knowledge and better dietary behavior were not associated with either sodium or potassium excretion but were moderately associated with sodium/potassium ratio. Copyright © 2016 Elsevier Inc. All rights reserved.

The chemistry of sodium chloride involvement in processes related to hot corrosion. [in gas turbine engines

NASA Technical Reports Server (NTRS)

Stearns, C. A.; Kohl, F. J.; Fryburg, G. C.

1979-01-01

Thermodynamic and mass transport calculations, and laboratory experiments elucidating the behavior of sodium chloride in combustion environments, in the deposition process, and in reactions with certain oxides on the surfaces of superalloys are summarized. It was found that some of the ingested salt is separated out of the air stream by the compressor. However, sodium chloride does pass from the compressor to the combustor where numerous chemical reactions take place. Here some of the salt is vaporized to yield gaseous sodium chloride molecules. Hydrogen and oxygen atoms present in the combustion products react with some sodium chloride to yield other gaseous species such as sodium, and a fraction of the salt remains as particulates. Both the gas phase and condensed sodium chloride can lead to sodium sulfate formation by various routes, all of which involve reaction with sulfur oxides and oxygen. In addition to contributing to the formation of sodium sulfate, the sodium chloride can contribute to corrosion directly.

Nanocomposite Materials for the Sodium-Ion Battery: A Review.

PubMed

Liang, Yaru; Lai, Wei-Hong; Miao, Zongcheng; Chou, Shu-Lei

2018-02-01

Clean energy has become an important topic in recent decades because of the serious global issues related to the development of energy, such as environmental contamination, and the intermittence of the traditional energy sources. Creating new battery-related energy storage facilities is an urgent subject for human beings to address and for solutions for the future. Compared with lithium-based batteries, sodium-ion batteries have become the new focal point in the competition for clean energy solutions and have more potential for commercialization due to the huge natural abundance of sodium. Nevertheless, sodium-ion batteries still exhibit some challenges, like inferior electrochemical performance caused by the bigger ionic size of Na + ions, the detrimental volume expansion, and the low conductivity of the active materials. To solve these issues, nanocomposites have recently been applied as a new class of electrodes to enhance the electrochemical performance in sodium batteries based on advantages that include the size effect, high stability, and excellent conductivity. In this Review, the recent development of nanocomposite materials applied in sodium-ion batteries is summarized, and the existing challenges and the potential solutions are presented. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Core-Shell PdPb@Pd Aerogels with Multiply-Twinned Intermetallic Nanostructures: Facile Synthesis with Accelerated Gelation Kinetics and Their Enhanced Electrocatalytic Properties

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhu, Chengzhou; Shi, Qiurong; Fu, Shaofang

2018-04-04

Delicately engineering the well-defined noble metal aerogels with favorable structural and compositional features is of vital importance for wide applications. Here, we reported one-pot and facile method for synthesizing core-shell PdPb@Pd hydrogels/aerogels with multiply-twinned grains and ordered intermetallic phase using sodium hypophosphite as a multifunctional reducing agent. Due to the accelerated gelation kinetics induced by increased reaction temperature and specific function of sodium hypophosphite, the formation of hydrogels can be completed within 4 hrs, far faster than the previous reports. Owe to their unique porous structure and favorable geometric and electronic effects, the optimized PdPb@Pd aerogels exhibit enhanced electrochemical performancemore » towards ethylene glycol oxidation with a mass activity of 5.8 times higher than Pd black.« less

Facile synthesis of 3D MnNi-layered double hydroxides (LDH)/graphene composites from directly graphites for pseudocapacitor and their electrochemical analysis

NASA Astrophysics Data System (ADS)

Lee, Ilbok; Jeong, Gyoung Hwa; An, Soyeon; Kim, Sang-Wook; Yoon, Songhun

2018-01-01

Herein, MnNi-layered double hydroxides (LDH) were imbibed within the interlayers of graphene nanosheets. The anionic surfactant, sodium dodecyl sulfate played a role of graphite exfoliator adding interaction with metal cations. Using this process, layered MnNi-LDH-graphene nanocomposite was prepared without formation of graphene oxide. When applied into pseudocapacitor electrode, LDH-graphene with optimal ratio between Mn and Ni exhibited very stable cycle with 90% at 1400 cycles and high energy 47.29 Wh kg-1 at the power density of 7473 W kg-1, which was attributed to highly stable layered LDH structure within conductive graphene layers.

Integrated Waste Treatment Unit (IWTU) Input Coal Analyses and Off-Gass Filter (OGF) Content Analyses

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jantzen, Carol M.; Missimer, David M.; Guenther, Chris P.

A full engineering scale Fluidized Bed Steam Reformer (FBSR) system is being used at the Idaho Nuclear Technology and Engineering Center (INTEC) to stabilize acidic Low Activity Waste (LAW) known as Sodium Bearing Waste (SBW). The INTEC facility, known as the Integrated Waste Treatment Unit (IWTU), underwent an Operational Readiness Review (ORR) and a Technology Readiness Assessment (TRA) in March 2014. The IWTU began non-radioactive simulant processing in late 2014 and by January, 2015 ; the IWTU had processed 62,000 gallons of simulant. The facility is currently in a planned outage for inspection of the equipment and will resume processingmore » simulated waste feed before commencing to process 900,000 gallons of radioactive SBW. The SBW acidic waste will be made into a granular FBSR product (carbonate based) for disposal in the Waste Isolation Pilot Plant (WIPP). In the FBSR process calcined coal is used to create a CO2 fugacity to force the waste species to convert to carbonate species. The quality of the coal, which is a feed input, is important because the reactivity, moisture, and volatiles (C,H,N,O, and S) in the coal impact the reactions and control of the mineralizing process in the primary steam reforming vessel, the Denitration and Mineralizing Reformer (DMR). Too much moisture in the coal can require that additional coal be used. However since moisture in the coal is only a small fraction of the moisture from the fluidizing steam this can be self-correcting. If the coal reactivity or heating value is too low then the coal feedrate needs to be adjusted to achieve the desired heat generation. Too little coal and autothermal heat generation in the DMR cannot be sustained and/or the carbon dioxide fugacity will be too low to create the desired carbonate mineral species. Too much coal and excess S and hydroxide species can form. Excess sulfur from coal that (1) is too rich in sulfur or (2) from overfeeding coal can promote wall scale and contribute to corrosion in process piping and materials, in excessive off-gas absorbent loading, and in undesired process emissions. The ash content of the coal is important as the ash adds to the DMR and other vessel products which affect the final waste product mass and composition. The amount and composition of the ash also affects the reaction kinetics. Thus ash content and composition contributes to the mass balance. In addition, sodium, potassium, calcium, sulfur, and maybe silica and alumina in the ash may contribute to wall-scale formation. Sodium, potassium, and alumina in the ash will be overwhelmed by the sodium, potassium, and alumina from the feed but the impact from the other ash components needs to be quantified. A maximum coal particle size is specified so the feed system does not plug and a minimum particle size is specified to prevent excess elutriation from the DMR to the Process Gas Filter (PGF). A vendor specification was used to procure the calcined coal for IWTU processing. While the vendor supplied a composite analysis for the 22 tons of coal (Appendix A), this study compares independent analyses of the coal performed at the Savannah River National Laboratory (SRNL) and at the National Energy Technology Laboratory (NETL). Three supersacks a were sampled at three different heights within the sack in order to determine within bag variability and between bag variability of the coal. These analyses were also compared to the vendor’s composite analyses and to the coal specification. These analyses were also compared to historic data on Bestac coal analyses that had been performed at Hazen Research Inc. (HRI) between 2004-2011.« less

CDC Vital Signs: Reducing Sodium in Children's Diets

MedlinePlus

... sodium options of your family's favorite foods. Request restaurant nutrition information to make lower sodium choices. Problem ... burritos and tacos; and soup. Processed foods and restaurant foods. Most sodium is already in food before ...

In-situ method for treating residual sodium

DOEpatents

Sherman, Steven R.; Henslee, S. Paul

2005-07-19

A unique process for deactivating residual sodium in Liquid Metal Fast Breeder Reactor (LMFBR) systems which uses humidified (but not saturated) carbon dioxide at ambient temperature and pressure to convert residual sodium into solid sodium bicarbonate.

In-Situ Method for Treating Residual Sodium

DOEpatents

Sherman, Steven R.; Henslee, S. Paul

2005-07-19

A unique process for deactivating residual sodium in Liquid Metal Fast Breeder Reactor (LMFBR) systems which uses humidified (but not saturated) carbon dioxide at ambient temperature and pressure to convert residual sodium into solid sodium bicarbonate.

Extraction of lead from waste CRT funnel glass by generating lead sulfide - An approach for electronic waste management.

PubMed

Hu, Biao; Hui, Wenlong

2017-09-01

Waste cathode ray tube (CRT) funnel glass is the key and difficult points in waste electrical and electronic equipment (WEEE) disposal. In this paper, a novel and effective process for the detoxification and reutilization of waste CRT funnel glass was developed by generating lead sulfide precipitate via a high-temperature melting process. The central function in this process was the generation of lead sulfide, which gathered at the bottom of the crucible and was then separated from the slag. Sodium carbonate was used as a flux and reaction agent, and sodium sulfide was used as a precipitating agent. The experimental results revealed that the lead sulfide recovery rate initially increased with an increase in the amount of added sodium carbonate, the amount of sodium sulfide, the temperature, and the holding time and then reached an equilibrium value. The maximum lead sulfide recovery rate was approximately 93%, at the optimum sodium carbonate level, sodium sulfide level, temperature, and holding time of 25%, 8%, 1200°C, and 2h, respectively. The glass slag can be made into sodium and potassium silicate by hydrolysis in an environmental and economical process. Copyright © 2017 Elsevier Ltd. All rights reserved.

THE HYDROTHERMAL REACTIONS OF MONOSODIUM TITANATE, CRYSTALLINE SILICOTITANATE AND SLUDGE IN THE MODULAR SALT PROCESS: A LITERATURE SURVEY

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fondeur, F.; Pennebaker, F.; Fink, S.

2010-11-11

The use of crystalline silicotitanate (CST) is proposed for an at-tank process to treat High Level Waste at the Savannah River Site. The proposed configuration includes deployment of ion exchange columns suspended in the risers of existing tanks to process salt waste without building a new facility. The CST is available in an engineered form, designated as IE-911-CW, from UOP. Prior data indicates CST has a proclivity to agglomerate from deposits of silica rich compounds present in the alkaline waste solutions. This report documents the prior literature and provides guidance for the design and operations that include CST to mitigatemore » that risk. The proposed operation will also add monosodium titanate (MST) to the supernate of the tank prior to the ion exchange operation to remove strontium and select alpha-emitting actinides. The cesium loaded CST is ground and then passed forward to the sludge washing tank as feed to the Defense Waste Processing Facility (DWPF). Similarly, the MST will be transferred to the sludge washing tank. Sludge processing includes the potential to leach aluminum from the solids at elevated temperature (e.g., 65 C) using concentrated (3M) sodium hydroxide solutions. Prior literature indicates that both CST and MST will agglomerate and form higher yield stress slurries with exposure to elevated temperatures. This report assessed that data and provides guidance on minimizing the impact of CST and MST on sludge transfer and aluminum leaching sludge.« less

LABORATORY STUDY FOR THE REDUCTION OF CHROME (VI) TO CHROME (III) USING SODIUM METABISULFITE UNDER ACIDIC CONDITIONS

DOE Office of Scientific and Technical Information (OSTI.GOV)

DUNCAM JB; GUTHRIE MD; LUECK KJ

2007-07-18

This report describes the results from RPP-PLAN-32738, 'Test Plan for the Effluent Treatment Facility to Reduce Chrome(VI) to Chrome(I1I) in the Secondary Waste Stream', using sodium metabisulfite. Appendix A presents the report as submitted by the Center for Laboratory Sciences (CLS) to CH2M HILL Hanford Group, Inc. The CLS carried out the laboratory effort under Contract Number 21065, release Number 30. This report extracts the more pertinent aspects of the laboratory effort.

Impact of the UK voluntary sodium reduction targets on the sodium content of processed foods from 2006 to 2011: analysis of household consumer panel data.

PubMed

Eyles, Helen; Webster, Jacqueline; Jebb, Susan; Capelin, Cathy; Neal, Bruce; Ni Mhurchu, Cliona

2013-11-01

In 2006 the UK Food Standards Agency (FSA) introduced voluntary sodium reduction targets for more than 80 categories of processed food. Our aim was to determine the impact of these targets on the sodium content of processed foods in the UK between 2006 and 2011. Household consumer panel data (n>18,000 households) were used to calculate crude and sales-weighted mean sodium content for 47,337 products in 2006 and 49,714 products in 2011. Two sample t-tests were used to compare means. A secondary analysis was undertaken to explore reformulation efforts and included only products available for sale in both 2006 and 2011. Between 2006 and 2011 there was an overall mean reduction in crude sodium content of UK foods of -26 mg/100g (p ≤ 0.001), equivalent to a 7% fall (356 mg/100g to 330 mg/100g). The corresponding sales-weighted reduction was -21 mg/100g (-6%). For products available for sale in both years the corresponding reduction was -23 mg/100g (p<0.001) or -7%. The UK FSA voluntary targets delivered a moderate reduction in the mean sodium content of UK processed foods between 2006 and 2011. Whilst encouraging, regular monitoring and review of the UK sodium reduction strategy will be essential to ensure continued progress. © 2013.

21 CFR 172.177 - Sodium nitrite used in processing smoked chub.

Code of Federal Regulations, 2010 CFR

2010-04-01

... SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) FOOD ADDITIVES PERMITTED FOR DIRECT ADDITION TO.... The food additive sodium nitrite may be safely used in combination with salt (NaCl) to aid in... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sodium nitrite used in processing smoked chub. 172...

Site Environmental Report for Calendar Year 2000. DOE Operations at The Boeing Company, Rocketdyne Propulsion & Power

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rutherford, Phil; Samuels, Sandy; Lee, Majelle

2001-09-01

This Annual Site Environmental Report (ASER) for 2000 describes the environmental conditions related to work performed for the Department of Energy (DOE) at Area IV of the Rocketdyne Santa Susana Field Laboratory (SSFL). In the past, these operations included development, fabrication, and disassembly of nuclear reactors, reactor fuel, and other radioactive materials, under the former Atomics International (AI) Division. Other activities included the operation of large-scale liquid metal facilities for testing of liquid metal fast breeder components at the Energy Technology Engineering Center (ETEC), a government-owned company-operated, test facility within Area IV. All nuclear work was terminated in 1988, andmore » subsequently, all radiological work has been directed toward decontamination and decommissioning (D&D) of the previously used nuclear facilities and associated site areas. Large-scale D&D activities of the sodium test facilities began in 1996. Results of the radiological monitoring program for the calendar year of 2000 continue to indicate no significant releases of radioactive material from Rocketdyne sites. All potential exposure pathways are sampled and/or monitored, including air, soil, surface water, groundwater, direct radiation, transfer of property (land, structures, waste), and recycling. All radioactive wastes are processed for disposal at DOE disposal sites and other sites approved by DOE and licensed for radioactive waste. Liquid radioactive wastes are not released into the environment and do not constitute an exposure pathway.« less

Peracetic Acid as a Green Disinfectant for Combined Sewer ...

EPA Pesticide Factsheets

This cooperative research and development agreement between U.S. EPA, Solvay, MSDGC, and CB&I is evaluating the potential of PAA for disinfection of Muddy Creek CSO wastewater and comparing that with sodium hypochlorite disinfection. This presentation will document the effectiveness of sodium hypochlorite and PAA for the inactivation of E. coli in CSO wastewater using laboratory bench-scale jar tests and Muddy Creek field site studies based on the following items:•Storage, shelf life, and application of the disinfectants.•Effectiveness of the disinfectants in the inactivation of E. coli.•Formation of harmful byproducts by the disinfectants.•Operation and maintenance costs, including the cost of the disinfectant, its storage, application, and neutralizing agent for the disinfectant to maintain the Ohio EPA guideline for residual disinfectant at the discharge point. Like many cities in the USA, Cincinnati, Ohio is attempting to find the best way to meet state and federal requirements concerning combined sewer overflow (CSO) wastewater. The Muddy Creek CSO treatment facility was constructed to provide treatment for CSO Numbers 198 and 216 from the Westwood Trunk sewer. The Metropolitan Sewer District of Greater Cincinnati (MSDGC) is currently using sodium hypochlorite for disinfection in this treatment facility. Because of degradation of hypochlorite during storage and the formation of chlorinated disinfection byproducts (DBPs), MSDGC is evaluating alternat

Facile synthesis of nickel-doped Co9S8 hollow nanoparticles with large surface-controlled pseudocapacitive and fast sodium storage

NASA Astrophysics Data System (ADS)

Zhou, Hepeng; Cao, Yijun; Ma, Zilong; Li, Shulei

2018-05-01

Transition metal sulfides are considered to be promising candidates as anodes for sodium ion batteries (SIBs). However, their further applications are limited by poor electrical conductivity and sluggish electrochemical kinetics. We report, for the first time, nickel-doped Co9S8 hollow nanoparticles as SIB anodes with enhanced electrical conductivity and a large pseudocapacitive effect, leading to fast kinetics. This compound exhibits excellent sodium storage performance, including a high capacity of 556.7 mA h g-1, a high rate capability of 2000 mA g-1 and an excellent stability up to 200 cycles. The results demonstrate that nickel-doped Co9S8 hollow nanoparticles are a promising anode material for SIBs.

Facile synthesis of nickel-doped Co9S8 hollow nanoparticles with large surface-controlled pseudocapacitive and fast sodium storage.

PubMed

Zhou, Hepeng; Cao, Yijun; Ma, Zilong; Li, Shulei

2018-05-11

Transition metal sulfides are considered to be promising candidates as anodes for sodium ion batteries (SIBs). However, their further applications are limited by poor electrical conductivity and sluggish electrochemical kinetics. We report, for the first time, nickel-doped Co 9 S 8 hollow nanoparticles as SIB anodes with enhanced electrical conductivity and a large pseudocapacitive effect, leading to fast kinetics. This compound exhibits excellent sodium storage performance, including a high capacity of 556.7 mA h g -1 , a high rate capability of 2000 mA g -1 and an excellent stability up to 200 cycles. The results demonstrate that nickel-doped Co 9 S 8 hollow nanoparticles are a promising anode material for SIBs.

Reduction-melting combined with a Na₂CO₃ flux recycling process for lead recovery from cathode ray tube funnel glass.

PubMed

Okada, Takashi; Yonezawa, Susumu

2014-08-01

With large quantity of flux (Na2CO3), lead can be recovered from the funnel glass of waste cathode-ray tubes via reduction-melting at 1000°C. To reduce flux cost, a technique to recover added flux from the generated oxide phase is also important in order to recycle the flux recovered from the reduction-melting process. In this study, the phase separation of sodium and the crystallization of water-soluble sodium silicates were induced after the reduction-melting process to enhance the leachability of sodium in the oxide phase and to extract the sodium from the phase for the recovery of Na2CO3 as flux. A reductive atmosphere promoted the phase separation and crystallization, and the leachability of sodium from the oxide phase was enhanced. The optimum temperature and treatment time for increasing the leachability were 700°C and 2h, respectively. After treatment, more than 90% of the sodium in the oxide phase was extracted in water. NaHCO3 can be recovered by carbonization of the solution containing sodium ions using carbon dioxide gas, decomposed to Na2CO3 at 50°C and recycled for use in the reduction-melting process. Copyright © 2014 Elsevier Ltd. All rights reserved.

TRIPLICATE SODIUM IODIDE GAMMA RAY MONITORS FOR THE SMALL COLUMN ION EXCHANGE PROGRAM

DOE Office of Scientific and Technical Information (OSTI.GOV)

Couture, A.

2011-09-20

This technical report contains recommendations from the Analytical Development (AD) organization of the Savannah River National Laboratory (SRNL) for a system of triplicate Sodium Iodide (NaI) detectors to be used to monitor Cesium-137 ({sup 137}Cs) content of the Decontaminated Salt Solution (DSS) output of the Small Column Ion Exchange (SCIX) process. These detectors need to be gain stabilized with respect to temperature shifts since they will be installed on top of Tank 41 at the Savannah River Site (SRS). This will be accomplished using NaI crystals doped with the alpha-emitting isotope, Americium-241({sup 241}Am). Two energy regions of the detector outputmore » will be monitored using single-channel analyzers (SCAs), the {sup 137}Cs full-energy {gamma}-ray peak and the {sup 241}Am alpha peak. The count rate in the gamma peak region will be proportional to the {sup 137}Cs content in the DSS output. The constant rate of alpha decay in the NaI crystal will be monitored and used as feedback to adjust the high voltage supply to the detector in response to temperature variation. An analysis of theoretical {sup 137}Cs breakthrough curves was used to estimate the gamma activity expected in the DSS output during a single iteration of the process. Count rates arising from the DSS and background sources were predicted using Microshield modeling software. The current plan for shielding the detectors within an enclosure with four-inch thick steel walls should allow the detectors to operate with the sensitivity required to perform these measurements. Calibration, testing, and maintenance requirements for the detector system are outlined as well. The purpose of SCIX is to remove and concentrate high-level radioisotopes from SRS salt waste resulting in two waste streams. The concentrated high-level waste containing {sup 137}Cs will be sent to the Defense Waste Processing Facility (DWPF) for vitrification and the low-level DSS will be sent to the Saltstone Production Facility (SPF) to be incorporated into grout.« less

Investigation of the chemical pathway of gaseous nitrogen dioxide formation during flue gas desulfurization with dry sodium bicarbonate injection

NASA Astrophysics Data System (ADS)

Stein, Antoinette Weil

The chemical reaction pathway for the viable flue gas desulfurization process, dry sodium bicarbonate injection, was investigated to mitigate undesirable plume discoloration. Based on a foundation of past findings, a simplified three-step reaction pathway was hypothesized for the formation of the plume-discoloring constituent, NO2. As the first step, it was hypothesized that sodium sulfite formed by sodium bicarbonate reaction with flue gas SO 2. As the second step, it was hypothesized that sodium nitrate formed by sodium sulfite reaction with flue gas NO. And as the third step, it was hypothesized that NO2 and sodium sulfate formed by sodium nitrate reaction with SO2. The second and third hypothesized steps were experimentally investigated using an isothermal fixed bed reactor. As reported in the past, technical grade sodium sulfite was found to be un-reactive with NO and O2. Freshly prepared sodium sulfite, maintained unexposed to moist air, was shown to react with NO and O2 resulting in a mixture of sodium nitrite and sodium nitrate together with a significant temperature rise. This reaction was found to proceed only when oxygen was present in the flue gas. As reported in the past, technical grade sodium nitrate was shown to be un-reactive with SO2. But freshly formed sodium nitrate kept unexposed to humidity was found to be reactive with SO2 and O 2 resulting in the formation of NO2 and sodium sulfate polymorphic Form I. The NO2 formation by this reaction was shown to be temperature dependent with maximum formation at 175°C. Plume mitigation methods were studied based on the validated three-step reaction pathway. Mitigation of NO2 was exhibited by limiting oxygen concentration in the flue gas to a level below 5%. It was also shown that significant NO2 mitigation was achieved by operating below 110°C or above 250°C. An innovative NO2 mitigation method was patented as a result of the findings of this study. The patented process incorporated a process step of sodium sulfite injection to remove flue gas NO prior to sodium bicarbonate injection.

Design of the Madison Dynamo Experiment

NASA Astrophysics Data System (ADS)

Kendrick, R. D.; Forest, C. B.; O'Connell, R.; Nornberg, M. D.; Spence, E. J.

2004-11-01

A spherical dynamo experiment has been constructed at the University of Wisconsin's liquid-sodium facility. The goals of the experiment are to observe and understand magnetic instabilities driven by flow shear in MHD systems, investigate MHD turbulence for magnetic Reynolds numbers of 100, and understand the role of fluid turbulence in current generation. Magnetic field generation is possible for only specific flow geometries. The experiment consists of a 1 m diameter, spherical stainless steel vessel filled with liquid sodium at 110 Celsius. The temperature of the vessel is maintained through an actively-heated-and-cooled oil heat-exchange system. Two 100 Hp motors with impellers drive flows in the liquid sodium with flow velocities near 15 m/s. Each shaft is sealed with an oil-buffered dual mechanical cartridge seal. The experiment is automated for remote operation and data logging. The melting and transfer of one metric ton of sodium to a storage vessel is discussed. Operating parameters and performance of the experiment are presented.

Thermochemical generation of hydrogen and oxygen from water

DOEpatents

Robinson, Paul R.; Bamberger, Carlos E.

1981-01-01

A thermochemical cyclic process for the production of hydrogen exploits the reaction between sodium manganate (NaMnO.sub.2) and titanium dioxide (TiO.sub.2) to form sodium titanate (Na.sub.2 TiO.sub.3), manganese (II) titanate (MnTiO.sub.3) and oxygen. The titanate mixture is treated with sodium hydroxide, in the presence of steam, to form sodium titanate, sodium manganate (III), water and hydrogen. The sodium titanate-manganate (III) mixture is treated with water to form sodium manganate (III), titanium dioxide and sodium hydroxide. Sodium manganate (III) and titanium dioxide are recycled following dissolution of sodium hydroxide in water.

Thermochemical generation of hydrogen and oxygen from water

DOEpatents

Robinson, Paul R.; Bamberger, Carlos E.

1982-01-01

A thermochemical cyclic process for the production of hydrogen exploits the reaction between sodium manganate (NaMnO.sub.2) and titanium dioxide (TiO.sub.2) to form sodium titanate (Na.sub.2 TiO.sub.3), manganese (II) titanate (MnTiO.sub.3) and oxygen. The titanate mixture is treated with sodium hydroxide, in the presence of steam, to form sodium titanate, sodium manganate (III), water and hydrogen. The sodium titanate-manganate (III) mixture is treated with water to form sodium manganate (III), titanium dioxide and sodium hydroxide. Sodium manganate (III) and titanium dioxide are recycled following dissolution of sodium hydroxide in water.

Understanding the Size-Dependent Sodium Storage Properties of Na2C6O6-Based Organic Electrodes for Sodium-Ion Batteries.

PubMed

Wang, Yaqun; Ding, Yu; Pan, Lijia; Shi, Ye; Yue, Zhuanghao; Shi, Yi; Yu, Guihua

2016-05-11

Organic electroactive materials represent a new generation of sustainable energy storage technology due to their unique features including environmental benignity, material sustainability, and highly tailorable properties. Here a carbonyl-based organic salt Na2C6O6, sodium rhodizonate (SR) dibasic, is systematically investigated for high-performance sodium-ion batteries. A combination of structural control, electrochemical analysis, and computational simulation show that rational morphological control can lead to significantly improved sodium storage performance. A facile antisolvent method was developed to synthesize microbulk, microrod, and nanorod structured SRs, which exhibit strong size-dependent sodium ion storage properties. The SR nanorod exhibited the best performance to deliver a reversible capacity of ∼190 mA h g(-1) at 0.1 C with over 90% retention after 100 cycles. At a high rate of 10 C, 50% of the capacity can be obtained due to enhanced reaction kinetics, and such high electrochemical activity maintains even at 80 °C. These results demonstrate a generic design route toward high-performance organic-based electrode materials for beyond Li-ion batteries. Using such a biomass-derived organic electrode material enables access to sustainable energy storage devices with low cost, high electrochemical performance and thermal stability.

One-step synthesis of polyaniline fibers with double-soft templates and evaluation of their doping process

NASA Astrophysics Data System (ADS)

Chen, Yong; Zhao, Hui; Han, Bing

2014-12-01

In this paper, we have developed a simple, facile, and efficient approach to synthesize polyaniline fibers (PANI fibers) from aniline in the presence of (NH4)2S2O8 with sodium dodecyl benzene sulfonate (SDBS) and L-camphorsulfonic acid (L-CSA) as double templates. The chemical constituents of the composites are characterized by Fourier transformation infrared spectroscopy (FTIR). The results demonstrate that the PANI fibers were synthesized successfully. The morphology of the composites was characterized by scanning electron microscopy (SEM). The SEM and UV-Vis images show an interesting growth and doping process. Moreover, cyclic voltammetry (CV) was used to characterize the electrochemical properties of PANI microfibers. They also give a pair of redox peaks and have better operation stability, which indicates that the composites show distinct electrochemical performance. So the PANI microfibers would have potential applications in the fields of analytical chemistry, bioanalysis, etc.

TRACER DISPERSION STUDIES FOR HYDRAULIC CHARACTERIZATION OF PIPES

EPA Science Inventory

A series of experiments were conducted at the U. S. Environmental Protection Agency (EPA) Test & Evaluation (T&E) Facility in Cincinnati, Ohio, to quantify longitudinal dispersion of a sodium fluoride tracer in polyvinyl chloride (PVC) pipe and ductile iron pipe under laminar, tr...

Overview of Fuel Rod Simulator Usage at ORNL

NASA Astrophysics Data System (ADS)

Ott, Larry J.; McCulloch, Reg

2004-02-01

During the 1970s and early 1980s, the Oak Ridge National Laboratory (ORNL) operated large out-of-reactor experimental facilities to resolve thermal-hydraulic safety issues in nuclear reactors. The fundamental research ranged from material mechanical behavior of fuel cladding during the depressurization phase of a loss-of-coolant accident (LOCA) to basic heat transfer research in gas- or sodium-cooled cores. The largest facility simulated the initial phase (less than 1 min. of transient time) of a LOCA in a commercial pressurized-water reactor. The nonnuclear reactor cores of these facilities were mimicked via advanced, highly instrumented electric fuel rod simulators locally manufactured at ORNL. This paper provides an overview of these experimental facilities with an emphasis on the fuel rod simulators.

Mechanism of sodium chloride in promoting reduction of high-magnesium low-nickel oxide ore

PubMed Central

Zhou, Shiwei; Wei, Yonggang; Li, Bo; Wang, Hua; Ma, Baozhong; Wang, Chengyan

2016-01-01

Sodium chloride has been proved that it is an effective promoter for the reduction of high-magnesium, low-nickel oxide ore. The aim of current work is to clarify the promotion behavior of sodium chloride in the roasting reduction process. The influence of moisture on the reduction of ore in the presence of sodium chloride is studied to get clear comprehension of promotion process. In the presence of moisture, the HCl is produced by pyrohydrolysis of sodium chloride for chlorinating nickel and iron oxides, moreover, interactions between metallic oxides and sodium chloride are also a way for chlorination at high temperature (>802 °C); subsequently, the metal chloride would be reduced by reductant. In the absence of moisture, the magnetic separation results show that the recoveries of iron and nickel have a significant increase; moreover, olivine structure would be destroyed gradually with the increase of roasting temperature in the action of sodium chloride, and the sodium chloride existed in high-magnesium, low-nickel oxide ore could make the NiO isolate from NiO-bearing minerals. The NiO reacts with Fe2O3 at high temperature to form NiFe2O4, which is conductive to the formation of Ni-Fe alloy during the reduction process. PMID:27374991

Mechanism of sodium chloride in promoting reduction of high-magnesium low-nickel oxide ore.

PubMed

Zhou, Shiwei; Wei, Yonggang; Li, Bo; Wang, Hua; Ma, Baozhong; Wang, Chengyan

2016-07-04

Sodium chloride has been proved that it is an effective promoter for the reduction of high-magnesium, low-nickel oxide ore. The aim of current work is to clarify the promotion behavior of sodium chloride in the roasting reduction process. The influence of moisture on the reduction of ore in the presence of sodium chloride is studied to get clear comprehension of promotion process. In the presence of moisture, the HCl is produced by pyrohydrolysis of sodium chloride for chlorinating nickel and iron oxides, moreover, interactions between metallic oxides and sodium chloride are also a way for chlorination at high temperature (>802 °C); subsequently, the metal chloride would be reduced by reductant. In the absence of moisture, the magnetic separation results show that the recoveries of iron and nickel have a significant increase; moreover, olivine structure would be destroyed gradually with the increase of roasting temperature in the action of sodium chloride, and the sodium chloride existed in high-magnesium, low-nickel oxide ore could make the NiO isolate from NiO-bearing minerals. The NiO reacts with Fe2O3 at high temperature to form NiFe2O4, which is conductive to the formation of Ni-Fe alloy during the reduction process.

Characterization and evaluation of amorphous carbon thin film (ACTF) for sodium ion adsorption

NASA Astrophysics Data System (ADS)

Fathy, Mahmoud; Mousa, Mahmoud Ahmed; Moghny, Th. Abdel; Awadallah, Ahmed E.

2017-12-01

The removal of sodium ions from aqueous solutions by adsorption onto amorphous carbon thin film (ACTF) has been studied in batch mode. In this work, the ACTF as new adsorbent was synthesized based on rice straw, then its structure and properties were taken into consideration to study its ability to adsorb sodium ions from synthetic water. The influence of pH, contact time, and temperature of the ion adsorption on ACTF was also studied using batch tests. We found that the contact time of sodium adsorption and its isothermal adsorption studied were described by pseudo-second-order kinetic model and Langmuir isotherm, respectively. Our results indicated that the adsorption of sodium ions on ACTF become be stronger and depends on pH, furthermore, the maximum adsorption capacities of sodium on ACTF recorded 107, 120 and 135 mg g-1 at 35, 45, and 65 °C. The thermodynamic parameters explain that the adsorption of sodium ions on ACTF is a spontaneous process and endothermic reaction. According to adsorption studies, we found that the ACTF can be used effectively for ion chromatography or desalinate sodium ion using ion exchange process in the hybrid desalination process with insignificant loss of adsorption capacity. However, the ACTF has better properties than any other carbon materials obtained from an agricultural byproduct.

SOLIDS PRECIPITATION EVENT IN MCU CAUSAL ANALYSIS AND RECOMMENDATIONS FROM SOLIDS RECOVERY TEAM

DOE Office of Scientific and Technical Information (OSTI.GOV)

Garrison, A.; Aponte, C.

A process upset occurred in the Modular Caustic-Side Solvent Extraction Unit (MCU) facility on April 6th, 2014. During recovery efforts, a significant amount of solids were found in the Salt Solution Feed Tank (SSFT), Salt Solution Receipt Tanks (SSRTs), two extraction contactors, and scrub contactors. The solids were identified by Savannah River National Laboratory (SRNL) as primarily sodium oxalate and sodium alumina silicate (NAS) with the presence of some aluminum hydroxide. NAS solids have been present in the SSFT since simulant runs during cold chemical startup of MCU in 2007, and have not hindered operations since that time. During themore » process upset in April 2014, the oxalate solids partially blocked the aqueous outlet of the extraction contactors, causing salt solution to exit through the contactor organic outlet to the scrub contactors with the organic phase. This salt solution overwhelmed the scrub contactors and passed with the organic phase to the strip section of MCU. The partially reversed flow of salt solution resulted in a Strip Effluent (SE) stream that was high in Isopar™ L, pH and sodium. The primary cause of the excessive solids accumulation in the SSRTs and SSFT at MCU is attributed to an increase in the frequency of oxalic acid cleaning of the 512-S primary filter. Agitation in the SSRTs at MCU in response to cold weather likely provided the primary mechanism to transfer the solids to the contactors. Sources of the sodium oxalate solids are attributed to the oxalic acid cleaning solution used to clean the primary filter at the Actinide Removal Process (ARP) filtration at 512-S, as well as precipitation from the salt batch feed, which is at or near oxalate saturation. The Solids Recovery Team was formed to determine the cause of the solids formation and develop recommendations to prevent or mitigate this event in the future. A total of 53 recommendations were generated. These recommendations were organized into 4 focus areas: • Improve understanding of oxalate equilibrium and kinetics in salt solutions • Reduction/elimination of oxalic acid cleaning in 512-S • Flowsheet optimization • Improving diagnostic capability The recommendations implemented prior to resumption of MCU operations provide a risk mitigation or detection function through additional sampling and observation. The longer term recommendations provide a framework to increase the basic process knowledge of both oxalate chemistry and filtration behavior and then facilitate decisions that improve the salt flowsheet as a system.« less

Strategies to reduce sodium consumption: a food industry perspective.

PubMed

Dötsch, Mariska; Busch, Johanneke; Batenburg, Max; Liem, Gie; Tareilus, Erwin; Mueller, Rudi; Meijer, Gert

2009-11-01

The global high prevalence of hypertension and cardiovascular disease has raised concerns regarding the sodium content of the foods which we consume. Over 75% of sodium intake in industrialized diets is likely to come from processed and restaurant foods. Therefore international authorities, such as the World Health Organisation, are encouraging the food industry to reduce sodium levels in their products. Significant sodium reduction is not without complications as salt plays an important role in taste, and in some products is needed also for preservation and processing. The most promising sodium reduction strategy is to adapt the preference of consumers for saltiness by reducing sodium in products in small steps. However, this is a time-consuming approach that needs to be applied industry-wide in order to be effective. Therefore the food industry is also investigating solutions that will maintain the same perceived salt intensity at lower sodium levels. Each of these has specific advantages, disadvantages, and time lines for implementation. Currently applied approaches are resulting in sodium reduction between 20-30%. Further reduction will require new technologies. Research into the physiology of taste perception and salt receptors is an emerging area of science that is needed in order to achieve larger sodium reductions.

PROCESS FOR REMOVING ALUMINUM COATINGS

DOEpatents

Flox, J.

1959-07-01

A process is presented for removing aluminum jackets or cans from uranium slugs. This is accomplished by immersing the aluminum coated uranium slugs in an aqueous solution of 9 to 20% sodium hydroxide and 35 to 12% sodium nitrate to selectively dissolve the aluminum coating, the amount of solution being such as to obtain a molar ratio of sodium hydroxide to aluminum of at least

One-pot synthesis of novel 1-(1H-tetrazol-5-yl)-1,2,3,4-tetrahydropyrrolo[1,2-a]pyrazine derivatives via an Ugi-azide 4CR process.

PubMed

Ghandi, Mehdi; Salahi, Saleh; Taheri, Abuzar; Abbasi, Alireza

2018-05-01

A facile one-pot method has been developed for the synthesis of novel pyrrolo[2,1-a]pyrazine scaffolds. A variety of 1-(1H-tetrazol-5-yl)-1,2,3,4-tetrahydropyrrolo[1,2-a]pyrazine derivatives were obtained in moderate to high yields in methanol using a one-pot four-component condensation of 1-(2-bromoethyl)-1H-pyrrole-2-carbaldehyde, amine, isocyanide and sodium azide at room temperature. These reactions presumably proceed via a domino imine formation, intramolecular annulation and Ugi-azide reaction. Unambiguous assignment of the molecular structures was carried out by single-crystal X-ray diffraction.

Controlled synthesis and luminescence properties of β-NaGdF4: Yb3+, Er3+ upconversion nanoparticles

NASA Astrophysics Data System (ADS)

Zhang, Yueli; Yao, Lu; Xu, Dekang; Lin, Hao; Yang, Shenghong

2018-06-01

β-NaGdF4:Yb3+,Er3+ upconversion (UC) nanoparticles (UCNPs) were prepared by a facile hydrothermal process with the assistance of sodium ethylene diaminetetraacetate salt (EDTA-2Na). The morphologies of the β-NaGdF4 UCNPs were controlled by changing the doses of EDTA-2Na and NaOH in precursor. With increasing concentration of EDTA-2Na in precursor, the size of crystals decreased, resulting in the decreasing of luminescence intensity. With increasing concentration of NaOH in precursor, the morphology became more homogeneous. However, due to the reduction of grain size and crystal quality, the luminescence intensity decreased. Nevertheless, the above results demonstrated a simple route to fabricate homogeneous UCNPs.

Compact Heat Exchanger Design and Testing for Advanced Reactors and Advanced Power Cycles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sun, Xiaodong; Zhang, Xiaoqin; Christensen, Richard

The goal of the proposed research is to demonstrate the thermal hydraulic performance of innovative surface geometries in compact heat exchangers used as intermediate heat exchangers (IHXs) and recuperators for the supercritical carbon dioxide (s-CO 2) Brayton cycle. Printed-circuit heat exchangers (PCHEs) are the primary compact heat exchangers of interest. The overall objectives are: To develop optimized PCHE designs for different working fluid combinations including helium to s-CO 2, liquid salt to s-CO 2, sodium to s-CO 2, and liquid salt to helium; To experimentally and numerically investigate thermal performance, thermal stress and failure mechanism of PCHEs under various transients;more » and To study diffusion bonding techniques for elevated-temperature alloys and examine post-test material integrity of the PCHEs. The project objectives were accomplished by defining and executing five different tasks corresponding to these specific objectives. The first task involved a thorough literature review and a selection of IHX candidates with different surface geometries as well as a summary of prototypic operational conditions. The second task involved optimization of PCHE design with numerical analyses of thermal-hydraulic performances and mechanical integrity. The subsequent task dealt with the development of testing facilities and engineering design of PCHE to be tested in s-CO 2 fluid conditions. The next task involved experimental investigation and validation of the thermal-hydraulic performances and thermal stress distribution of prototype PCHEs manufactured with particular surface geometries. The last task involved an investigation of diffusion bonding process and posttest destructive testing to validate mechanical design methods adopted in the design process. The experimental work utilized the two test facilities at The Ohio State University (OSU) including one existing High-Temperature Helium Test Facility (HTHF) and the newly developed s-CO 2 test loop (STL) facility and s-CO 2 test facility at University of Wisconsin – Madison (UW).« less

Thermochemical generation of hydrogen and oxygen from water. [NaMnO/sub 2/ and TiO/sub 2/

DOEpatents

Robinson, P.R.; Bamberger, C.E.

1980-02-08

A thermochemical cyclic process for the production of hydrogen exploits the reaction between sodium manganate (NaMnO/sub 2/) and titanium dioxide (TiO/sub 2/) to form sodium titanate (Na/sub 2/TiO/sub 3/), manganese (II) titanate (MnTiO/sub 3/) and oxygen. The titanate mixture is treated with sodium hydroxide, in the presence of steam, to form sodium titanate, sodium manganate (III), water and hydrogen. The sodium titanate-manganate (III) mixture is treated with water to form sodium manganate (III), titanium dioxide and sodium hydroxide. Sodium manganate (III) and titanium dioxide are recycled following dissolution of sodium hydroxide in water.

Facile Stabilization of the Sodium Metal Anode with Additives: Unexpected Key Role of Sodium Polysulfide and Adverse Effect of Sodium Nitrate.

PubMed

Wang, Huan; Wang, Chuanlong; Matios, Edward; Li, Weiyang

2018-06-25

Sodium metal is an attractive anode for next-generation energy storage systems owing to its high specific capacity, low cost, and high abundance. Nevertheless, uncontrolled Na dendrite growth caused by the formation of unstable solid electrolyte interphase (SEI) leads to poor cycling performance and severe safety concerns. Sodium polysulfide (Na 2 S 6 ) alone is revealed to serve as a positive additive or pre-passivation agent in ether electrolyte to improve the long-term stability and reversibility of the Na anode, while Na 2 S 6 -NaNO 3 as co-additive has an adverse effect, contrary to the prior findings in the lithium anode system. A superior cycling behavior of Na anode is first demonstrated at a current density up to 10 mA cm -2 and a capacity up to 5 mAh cm -2 over 100 cycles. As a proof of concept, a high-capacity Na-S battery was prepared by pre-passivating the Na anode with Na 2 S 6 . This study gives insights into understanding the differences between Li and Na systems. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Magnetic Eigenmodes in the Madison Dynamo Experiment

NASA Astrophysics Data System (ADS)

Nornberg, M. D.; Bayliss, R. A.; Forest, C. B.; Kendrick, R. D.; O'Connell, R.; Spence, E. J.

2002-11-01

A spherical dynamo experiment has been constructed at the University of Wisconsin's liquid sodium facility. The goals of the experiment are to observe and understand magnetic instabilities driven by flow shear in MHD systems, investigate MHD turbulence for magnetic Reynolds numbers of 100, and understand the role of fluid turbulence in current generation. Magnetic field generation is only possible for specific flow geometries. We have studied and achieved simple roll flow geometries in a full scale water experiment. Results from the water experiment have guided the design of the sodium experiment. The experiment consists of a 1 m diameter, spherical stainless steel vessel filled with liquid sodium at 110 Celsius. Two 100 Hp motors with impellers drive flows in the liquid sodium with flow velocities of 15 m/s. A gaussian grid of 66 Hall probes on the surface of the sodium vessel measure the generated external magnetic field. Hall probe feed-thru arrays measure the internal field. A pair of magnetic field coils produce a roughly uniform field inside the sphere with a centerline field strength of 100 gauss. Preliminary investigations include measurements of the turbulent electromotive force and excitation of magnetic eigenmodes.

Waste separation and pretreatment using crystalline silicotitanate ion exchangers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tadros, M.E.; Miller, J.E.; Anthony, R.G.

1997-10-01

A new class of inorganic ion exchangers called crystalline silicotitanates (CSTs) has been developed jointly by Sandia National Laboratories and Texas A&M University to selectively remove Cs and other radionuclides from a wide spectrum of radioactive defense wastes. The CST exhibits high selectivity and affinity for Cs and Sr under a wide range of conditions. Tests show it can remove part-per-million concentrations of Cs{sup +} from highly alkaline, high-sodium simulated radioactive waste solutions modeled after those at Hanford, Oak Ridge, and Savannah River. The materials exhibit ion exchange properties based on ionic size selectivity. Specifically, crystalline lattice spacing is controlledmore » to be highly selective for Cs ions even in waste streams containing very high (5 to 10 M) concentrations of sodium. The CST technology is being demonstrated with actual waste at several DOE facilities. The use of inorganic ion exchangers. The inorganics are more resistant to chemical, thermal, and radiation degradation. Their high selectivities result in more efficient operations offering the possibility of a simple single-pass operation. In contrast, regenerable organic ion exchangers require additional processing equipment to handle the regeneration liquids and the eluant with the dissolved Cs.« less

ENGINEERING AND CONSTRUCTING THE HALLAM NUCLEAR POWER FACILITY REACTOR STRUCTURE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mahlmeister, J E; Haberer, W V; Casey, D F

1960-12-15

The Hallam Nuclear Power Facility reactor structure, including the cavity liner, is described, and the design philosophy and special design requirements which were developed during the preliminary and final engineering phases of the project are explained. The structure was designed for 600 deg F inlet and 1000 deg F outlet operating sodium temperatures and fabricated of austenitic and ferritic stainless steels. Support for the reactor core components and adequate containment for biological safeguards were readily provided even though quite conservative design philosophy was used. The calculated operating characteristics, including heat generation, temperature distributions and stress levels for full-power operation, aremore » summarized. Ship fabrication and field installation experiences are also briefly related. Results of this project have established that the sodium graphite reactor permits practical and economical fabrication and field erection procedures; considerably higher operating design temperatures are believed possible without radical design changes. Also, larger reactor structures can be similarly constructed for higher capacity (300 to 1000 Mwe) nuclear power plants. (auth)« less

Core–shell PdPb@Pd aerogels with multiply-twinned intermetallic nanostructures: facile synthesis with accelerated gelation kinetics and their enhanced electrocatalytic properties

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhu, Chengzhou; Shi, Qiurong; Fu, Shaofang

Delicately engineering the well-defined noble metal aerogels with favorable structural and compositional features is of vital importance for wide applications. Here, we reported one-pot and facile method for synthesizing core-shell PdPb@Pd hydrogels/aerogels with multiply-twinned grains and ordered intermetallic phase using sodium hypophosphite as a multifunctional reducing agent. Due to the accelerated gelation kinetics induced by increased reaction temperature and specific function of sodium hypophosphite, the formation of hydrogels can be completed within 4 hrs, far faster than the previous reports. Owe to their unique porous structure and favorable geometric and electronic effects, the optimized PdPb@Pd aerogels exhibit enhanced electrochemical performancemore » towards ethylene glycol oxidation with a mass activity of 5.8 times higher than Pd black.Core–shell PdPb@Pd aerogels with multiply-twinned grains and an ordered intermetallic phase was synthesized, which exhibited good electrocatalytic activity towards ethanol oxidation.« less

System of closing relations of a two-fluid model for the HYDRA-IBRAE/LM/V1 code for calculation of sodium boiling in channels of power equipment

NASA Astrophysics Data System (ADS)

Usov, E. V.; Butov, A. A.; Dugarov, G. A.; Kudasov, I. G.; Lezhnin, S. I.; Mosunova, N. A.; Pribaturin, N. A.

2017-07-01

The system of equations from a two-fluid model is widely used in modeling thermohydraulic processes during accidents in nuclear reactors. The model includes conservation equations governing the balance of mass, momentum, and energy in each phase of the coolant. The features of heat and mass transfer, as well as of mechanical interaction between phases or with the channel wall, are described by a system of closing relations. Properly verified foreign and Russian codes with a comprehensive system of closing relations are available to predict processes in water coolant. As to the sodium coolant, only a few open publications on this subject are known. A complete system of closing relations used in the HYDRA-IBRAE/LM/V1 thermohydraulic code for calculation of sodium boiling in channels of power equipment is presented. The selection of these relations is corroborated on the basis of results of analysis of available publications with an account taken of the processes occurring in liquid sodium. A comparison with approaches outlined in foreign publications is presented. Particular attention has been given to the calculation of the sodium two-phase flow boiling. The flow regime map and a procedure for the calculation of interfacial friction and heat transfer in a sodium flow with account taken of high conductivity of sodium are described in sufficient detail. Correlations are presented for calculation of heat transfer for a single-phase sodium flow, sodium flow boiling, and sodium flow boiling crisis. A method is proposed for prediction of flow boiling crisis initiation.

Survival and Risk Comparison of Campylobacter jejuni on Various Processed Meat Products

PubMed Central

Hong, Soo Hyeon; Kim, Han Sol; Yoon, Ki Sun

2016-01-01

The objective of this study was to investigate survival kinetics of Campylobacter jejuni on various processed meat products (dry-cured ham, round ham with/without sodium nitrite, garlic seasoned ham with/without sodium nitrite, and sausage without sodium nitrite). Additionally, a semi-quantitative risk assessment of C. jejuni on various processed meat products was conducted using FDA-iRISK 1.0. Inoculated processed meat products with 6.0 ± 0.5 log CFU/g of C. jejuni were vacuum packed and stored at 4, 10, 17, 24, 30, and 36 °C. Survival curves were fitted to the Weibull model to obtain the delta values of C. jejuni on various processed meat products. The most rapid death of C. jejuni was observed on dry-cured ham, followed by sausage without sodium nitrite. The results of semi-quantitative risk assessment indicate that dry-cured ham represented the lowest risk among all samples. C. jejuni on processed meats presented a greater risk at 4 °C than at 10 °C. The risk of ham was greater than the risk of sausage, regardless of type. Among all samples, the highest risk of C. jejuni was observed in round ham without sodium nitrite. Overall, our data indicates that risk of processed meat products due to C. jejuni is relatively low. PMID:27294947

Dietary sodium reduction in New Zealand: influence of the Tick label.

PubMed

Ning, Sherry X; Mainvil, Louise A; Thomson, Rachel K; McLean, Rachel M

2017-01-01

The Tick programme of the National Heart Foundation (NHF) is the longest standing voluntary front of pack signpost nutrition logo in New Zealand. It provides a platform for collaboration with the food industry to encourage development of healthier products. This study evaluated the impact of the Tick programme on sodium in processed food. Fifty-two Tick programme products from food categories known to contribute substantially to sodium intake were identified. Sales volumes (kg) from January 2011 to December 2013 were multiplied by changes in sodium content over that time, producing an estimate of programme impact. Five semi-structured interviews with industry representatives were conducted, to look at other influences for sodium reduction, and themes identified through methods of thematic analysis. Over the period, the Tick programme influenced food companies to remove approximately 16 tonnes of salt through the reformulation and formulation of 52 Tick-approved breakfast cereals, edible oil spreads, cooking sauces and processed poultry products. Other factors influencing sodium reduction reported by company representatives included increased consumer and industry interest in healthier product nutrition profiles and other sodium reduction programmes targeting reformulation/formulation. The Tick remains a credible and well-recognized brand and may provide a competitive edge for participating food manufacturers in the current market. The Tick programme is effective in influencing industry to reduce sodium in processed foods in New Zealand. The combined impact of the Tick and other NHF programmes has the potential to reduce population sodium intake and improve health outcomes.

FY 2017 Status of Sodium Freezing and Remelting Tests

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lv, Q.; Boron, E.; Momozaki, Y.

The Sodium Freezing and Remelting experiment facility at Argonne National Laboratory has been significantly modified and improved. The main improvement was replacement of the two original stainless steel test sections that had strain gages limited by their bonds to the stainless steel to maximum temperatures of 350°C with a single new test section with strain gages that can be utilized up to 980°C and a thin wall to enhance measured strains. Wetting of stainless steel by sodium within a practical time of one to a few days is expected to require temperatures of 450°C or greater. Thus, the higher temperaturemore » strain gages enable wetting in a short time of a few days. Wetting below 350°C would have required an impractically long time of at least weeks. Other improvements included upgrading of the loop configuration, incorporation of a cold finger to purify sodium, a new data acquisition system, and reinstallation of the many heaters, heater controllers, and thermocouples. After the loop had been heated to 400°C for about two hours, an initial sodium freezing test was conducted. It is thought that the sodium might have at least partially wetted the stainless steel wall under these conditions. The strain gage measurements indicate that an incremental step inward deformation of the test section thin wall occurred as the temperature decreased through the sodium freezing temperature. This behavior is consistent with sodium initially adhering to the stainless steel inner wall but breaking away from the wall as the freezing sodium contracted. Conduct of additional sodium freezing tests under well wetted conditions was prevented as a result of stoppage of all electrical work at Argonne by the Laboratory Director on July 25, 2017. A pathway to resuming electrical work is now in place at Argonne and additional sodium freezing testing will resume next fiscal year.« less

Management of Sodium-reduced Meals at Worksite Cafeterias: Perceptions, Practices, Barriers, and Needs among Food Service Personnel.

PubMed

Lee, Jounghee; Park, Sohyun

2016-04-01

The sodium content of meals provided at worksite cafeterias is greater than the sodium content of restaurant meals and home meals. The objective of this study was to assess the relationships between sodium-reduction practices, barriers, and perceptions among food service personnel. We implemented a cross-sectional study by collecting data on perceptions, practices, barriers, and needs regarding sodium-reduced meals at 17 worksite cafeterias in South Korea. We implemented Chi-square tests and analysis of variance for statistical analysis. For post hoc testing, we used Bonferroni tests; when variances were unequal, we used Dunnett T3 tests. This study involved 104 individuals employed at the worksite cafeterias, comprised of 35 men and 69 women. Most of the participants had relatively high levels of perception regarding the importance of sodium reduction (very important, 51.0%; moderately important, 27.9%). Sodium reduction practices were higher, but perceived barriers appeared to be lower in participants with high-level perception of sodium-reduced meal provision. The results of the needs assessment revealed that the participants wanted to have more active education programs targeting the general population. The biggest barriers to providing sodium-reduced meals were use of processed foods and limited methods of sodium-reduced cooking in worksite cafeterias. To make the provision of sodium-reduced meals at worksite cafeterias more successful and sustainable, we suggest implementing more active education programs targeting the general population, developing sodium-reduced cooking methods, and developing sodium-reduced processed foods.

Separation of sodium-22 from irradiated targets

DOEpatents

Taylor, Wayne A.; Jamriska, David

1996-01-01

A process for selective separation of sodium-22 from an irradiated target including dissolving an irradiated target to form a first solution, contacting the first solution with hydrated antimony pentoxide to selectively separate sodium-22 from the first solution, separating the hydrated antimony pentoxide including the separated sodium-22 from the first solution, dissolving the hydrated antimony pentoxide including the separated sodium-22 in a mineral acid to form a second solution, and, separating the antimony from the sodium-22 in the second solution.

Sodium citrate (Na{sub 3}Cit)-assisted hydrothermal synthesis of uniform spindle-like SrMoO{sub 4}:Eu{sup 3+} phosphors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ren, Xiaolei; Zhang, Yu; Li, Qiuyu

2014-11-15

Graphical abstract: A facile hydrothermal method for the synthesis of uniform spindle-like SrMoO{sub 4}:Eu{sup 3+} phosphors with the assistance of sodium citrate (Na{sub 3}Cit). - Highlights: • Well-crystallized spindle-like SrMoO{sub 4}:Eu{sup 3+} phosphors have been synthesized. • The influence of the reaction temperature and reaction time were clearly shown. • The dosage of Na{sub 3}Cit has a strong effect on the spindle-like SrMoO{sub 4}:Eu{sup 3+} phosphors. • The growth mechanism for the formation of final samples was proposed. - Abstract: Highly uniform spindle-like SrMoO{sub 4}:Eu{sup 3+} phosphors have been prepared by a facile hydrothermal method using sodium citrate (Na{sub 3}Cit)more » as the chelating reagent. X-ray powder diffraction (XRD), field emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray spectrum (EDS), transmission electron microscopy (TEM), X-ray photoelectron spectra (XPS), Fourier transform-infrared spectroscopy (FT-IR) and photoluminescence spectra (PL) were used to characterize the resulting samples. The dosage of sodium citrate, reaction temperature and reaction time play key roles in the formation of the final samples. The possible formation mechanism for SrMoO{sub 4}:Eu{sup 3+} phosphors has been proposed. Upon excitation by ultraviolet radiation, the as-synthesized SrMoO{sub 4}:Eu{sup 3+} phosphors show the characteristic {sup 5}D{sub 0}–{sup 7}F{sub J} (J = 1, 2, 3, 4) emission lines with red emission {sup 5}D{sub 0}–{sup 7}F{sub 2} (613 nm) as the most prominent group.« less

Cation exchange in a glacial till drumlin at a road salt storage facility

NASA Astrophysics Data System (ADS)

Ostendorf, David W.; Xing, Baoshan; Kallergis, Niki

2009-05-01

We use laboratory and field data to calibrate existing geochemical and transport models of cation exchange induced by contamination of an unconfined aquifer at a road salt storage facility built upon a glacial till drumlin in eastern Massachusetts. A Gaines and Thomas selectivity coefficient K models the equilibrium sodium and divalent cation distribution in the groundwater and solid matrix, while an existing method of characteristics model describes the advective transport of total dissolved cations and sorbed sodium. Laboratory isotherms of split spoon soil samples from the drumlin calibrate K with an average value of 0.0048 (L/g) 1/2 for a measured cation exchange capacity of 0.057 meq/g dry soil. Ten years of monitoring well data document groundwater flow and the advection of conservative chloride due to outdoor storage and handling of road salt at the site. The monitoring well cation data and retarded transport model offer an independent K calibration of 0.0040 to 0.0047 (L/g) 1/2: the consistency of the field and laboratory selectivity coefficient calibrations endorse this application of the Gaines and Thomas and method of characteristics models. The advancing deicing agent plume releases divalent cations from the till into the groundwater, so that monitoring well samples do not reflect the chemical composition of the road salt. In this regard, dissolved divalent cation milliequivalent concentrations are as high as 80% of the total dissolved cationic concentrations in the salt contaminated monitoring well samples, far greater than their 2.5% level in the road salt stored at the site. Cation exchange can thus obscure attempts to hindcast stored road salt sodium water table concentration from monitoring well sample stoichiometry, or to predict sodium impacts on groundwater or receiving stream quality downgradient of the well.

Cation exchange in a glacial till drumlin at a road salt storage facility.

PubMed

Ostendorf, David W; Xing, Baoshan; Kallergis, Niki

2009-05-12

We use laboratory and field data to calibrate existing geochemical and transport models of cation exchange induced by contamination of an unconfined aquifer at a road salt storage facility built upon a glacial till drumlin in eastern Massachusetts. A Gaines and Thomas selectivity coefficient K models the equilibrium sodium and divalent cation distribution in the groundwater and solid matrix, while an existing method of characteristics model describes the advective transport of total dissolved cations and sorbed sodium. Laboratory isotherms of split spoon soil samples from the drumlin calibrate K with an average value of 0.0048 (L/g)(1/2) for a measured cation exchange capacity of 0.057 meq/g dry soil. Ten years of monitoring well data document groundwater flow and the advection of conservative chloride due to outdoor storage and handling of road salt at the site. The monitoring well cation data and retarded transport model offer an independent K calibration of 0.0040 to 0.0047 (L/g)(1/2): the consistency of the field and laboratory selectivity coefficient calibrations endorse this application of the Gaines and Thomas and method of characteristics models. The advancing deicing agent plume releases divalent cations from the till into the groundwater, so that monitoring well samples do not reflect the chemical composition of the road salt. In this regard, dissolved divalent cation milliequivalent concentrations are as high as 80% of the total dissolved cationic concentrations in the salt contaminated monitoring well samples, far greater than their 2.5% level in the road salt stored at the site. Cation exchange can thus obscure attempts to hindcast stored road salt sodium water table concentration from monitoring well sample stoichiometry, or to predict sodium impacts on groundwater or receiving stream quality downgradient of the well.

The Effects of Voltage and Concentration of Sodium Bicarbonate on Electrochemical Synthesis of Ethanol from Carbon Dioxide Using Brass as Cathode

NASA Astrophysics Data System (ADS)

Ramadan, Septian; Fariduddin, Sholah; Rizki Aminudin, Afianti; Kurnia Hayatri, Antisa; Riyanto

2017-11-01

The effects of voltage and concentration of sodium bicarbonate were investigated to determine the optimum conditions of the electrochemical synthesis process to convert carbon dioxide into ethanol. The conversion process is carried out using a sodium bicarbonate electrolyte solution in an electrochemical synthesis reactor equipped with a cathode and anode. As the cathode was used brass, while as the anode carbon was utilized. Sample of the electrochemical synthesis process was analyzed by gas chromatography to determine the content of the compounds produced. The optimum electrochemical synthesis conditions to convert carbon dioxide into ethanol are voltage and concentration of sodium bicarbonate are 3 volts and 0.4 M with ethanol concentration of 1.33%.

Modeled changes in U.S. sodium intake from reducing sodium concentrations of commercially-processed and prepared foods to meet voluntary standards established in North America: National Health and Nutrition Examination Survey

USDA-ARS?s Scientific Manuscript database

About 2 in 3 U.S. adults have pre-hypertension or hypertension increasing their risk of cardiovascular disease. Reducing sodium intake can decrease blood pressure and prevent hypertension. About 9 in 10 Americans consume excess sodium, >2300 mg daily. Voluntary sodium reduction standards for commerc...

Electrolytic recovery of reactor metal fuel

DOEpatents

Miller, W.E.; Tomczuk, Z.

1994-09-20

A new electrolytic process and apparatus are provided using sodium, cerium or a similar metal in alloy or within a sodium beta or beta[double prime]-alumina sodium ion conductor to electrolytically displace each of the spent fuel metals except for cesium and strontium on a selective basis from the electrolyte to an inert metal cathode. Each of the metals can be deposited separately. An electrolytic transfer of spent fuel into the electrolyte includes a sodium or cerium salt in the electrolyte with sodium or cerium alloy being deposited on the cathode during the transfer of the metals from the spent fuel. The cathode with the deposit of sodium or cerium alloy is then shunted to an anode and the reverse transfer is carried out on a selective basis with each metal being deposited separately at the cathode. The result is that the sodium or cerium needed for the process is regenerated in the first step and no additional source of these reactants is required. 2 figs.

Electrolytic recovery of reactor metal fuel

DOEpatents

Miller, W.E.; Tomczuk, Z.

1993-02-03

This invention is comprised of a new electrolytic process and apparatus using sodium, cerium or a similar metal in an alloy or within a sodium beta or beta-alumina sodium ion conductor to electrolytically displace each of the spent fuel metals except for Cesium and strontium on a selective basis from the electrolyte to an inert metal cathode. Each of the metals can be deposited separately. An electrolytic transfer of spent fuel into the electrolyte includes a sodium or cerium salt in the electrolyte with sodium or cerium alloy being deposited on the cathode during the transfer of the metals from the spent fuel. The cathode with the deposit of sodium or cerium alloy is then changed to an anode and the reverse transfer is carried out on a selective basis with each metal being deposited separately at the cathode. The result is that the sodium or cerium needed for the process is regenerated in the first step and no additional source of these reactants is required.

Electrolytic recovery of reactor metal fuel

DOEpatents

Miller, William E.; Tomczuk, Zygmunt

1994-01-01

A new electrolytic process and apparatus are provided using sodium, cerium or a similar metal in alloy or within a sodium beta or beta"-alumina sodium ion conductor to electrolytically displace each of the spent fuel metals except for cesium and strontium on a selective basis from the electrolyte to an inert metal cathode. Each of the metals can be deposited separately. An electrolytic transfer of spent fuel into the electrolyte includes a sodium or cerium salt in the electrolyte with sodium or cerium alloy being deposited on the cathode during the transfer of the metals from the spent fuel. The cathode with the deposit of sodium or cerium alloy is then chanted to an anode and the reverse transfer is carried out on a selective basis with each metal being deposited separately at the cathode. The result is that the sodium or cerium needed for the process is regenerated in the first step and no additional source of these reactants is required.

Interlaboratory study of free cyanide methods compared to total cyanide measurements and the effect of preservation with sodium hydroxide for secondary- and tertiary-treated waste water samples.

PubMed

Stanley, Brett J; Antonio, Karen

2012-11-01

Several methods exist for the measurement of cyanide levels in treated wastewater,typically requiring preservation of the sample with sodium hydroxide to minimize loss of hydrogen cyanide gas (HCN). Recent reports have shown that cyanide levels may increase with chlorination or preservation. In this study, three flow injection analysis methods involving colorimetric and amperometric detection were compared within one laboratory, as well as across separate laboratories and equipment. Split wastewater samples from eight facilities and three different sampling periods were tested. An interlaboratory confidence interval of 3.5 ppb was calculated compared with the intralaboratory reporting limit of 2 ppb. The results show that free cyanide measurements are not statistically different than total cyanide levels. An artificial increase in cyanide level is observed with all methods for preserved samples relative to nonpreserved samples, with an average increase of 2.3 ppb. The possible loss of cyanide without preservation is shown to be statistically insignificant if properly stored up to 48 hours. The cyanide increase with preservation is further substantiated with the method of standard additions and is not a matrix interference. The increase appears to be correlated with the amount of cyanide observed without preservation, which appears to be greater in those facilities that disinfect their wastewater with chlorine, followed by dechlorination with sodium bisulfite.

Metallization pattern on solid electrolyte or porous support of sodium battery process

DOEpatents

Kim, Jin Yong; Li, Guosheng; Lu, Xiaochuan; Sprenkle, Vincent L.; Lemmon, John P.

2016-05-31

A new battery configuration and process are detailed. The battery cell includes a solid electrolyte configured with an engineered metallization layer that distributes sodium across the surface of the electrolyte extending the active area of the cathode in contact with the anode during operation. The metallization layer enhances performance, efficiency, and capacity of sodium batteries at intermediate temperatures at or below about 200.degree. C.

Balancing Sodium Impurities in Alumina for Improved Properties

NASA Astrophysics Data System (ADS)

Wijayaratne, Hasini; Hyland, Margaret; McIntosh, Grant; Perander, Linus; Metson, James

2018-06-01

As there are direct and indirect impacts of feed material purity on the aluminum production process and metal grade, there is a high demand on the so-called pure smelter grade alumina (SGA)—the main feedstock for aluminum production. In this work, impurities within the precursor gibbsite used for SGA production and SGA are studied using NanoSIMS and XPS with a focus on sodium—the most abundant impurity. Although the industry trend is towards minimizing sodium due to the well-known negative impacts on the process, high sodium is also correlated with relatively attrition-resistant calcined products. Here, we show that this relationship is indirect and arises from sodium's role in inhibiting α-alumina formation. Alpha alumina formation in SGA has previously been demonstrated to induce a macro-porous and therefore attrition-prone microstructure. Sodium distribution within the precursor gibbsite and its migration during the calcination process are proposed to be most likely responsible for the spatial distribution of α-alumina within the calcined product grain. This in turn determines the behavior of the product during its transportation and handling (i.e., attrition). Therefore, tolerance of a certain amount of sodium within the precursor material does demonstrate a net benefit while balancing its negative impacts on the process.

Evaluation of a Biological Pathogen Decontamination Protocol for Animal Feed Mills.

PubMed

Huss, Anne R; Cochrane, Roger A; Deliephan, Aiswariya; Stark, Charles R; Jones, Cassandra K

2015-09-01

Animal feed and ingredients are potential vectors of pathogenic bacteria. Contaminated ingredients can contaminate facility equipment, leading to cross-contamination of other products. This experiment was conducted to evaluate a standardized protocol for decontamination of an animal feed manufacturing facility using Enterococcus faecium (ATCC 31282) as an indicator. A pelleted swine diet inoculated with E. faecium was manufactured, and environmental samples (swabs, replicate organism detection and counting plates, and air samples) were collected (i) before inoculation (baseline data), (ii) after production of inoculated feed, (iii) after physical removal of organic material using pressurized air, (iv) after application of a chemical sanitizer containing a quaternary ammonium-glutaraldehyde blend, (v) after application of a chemical sanitizer containing sodium hypochlorite, (vi) after facility heat-up to 60 8 C for 24 h, (vii) for 48 h, and (viii) for 72 h. Air samples collected outside the facility confirmed pathogen containment; E. faecium levels were equal to or lower than baseline levels at each sample location. The decontamination step and its associated interactions were the only variables that affected E. faecium incidence (P < 0.0001 versus P > 0.22). After production of the inoculated diet, 85.7% of environmental samples were positive for E. faecium. Physical cleaning of equipment had no effect on contamination (P = 0.32). Chemical cleaning with a quaternary ammonium-glutaraldehyde blend and sodium hypochlorite each significantly reduced E. faecium contamination (P < 0.0001) to 28.6 and 2.4% of tested surfaces, respectively. All samples were negative for E. faecium after 48 h of heating. Both wet chemical cleaning and facility heating but not physical cleaning resulted in substantial E. faecium decontamination. These results confirmed both successful containment and decontamination of biological pathogens in the tested pilot-scale feed mill.

Process for preparing titanium nitride powder

DOEpatents

Bamberger, C.E.

1988-06-17

A process for making titanium nitride powder by reaction of titanium phosphates with sodium cyanide. The process of this invention may comprise mixing one or more phosphates of Ti with a cyanide salt in the absence of oxygen and heating to a temperature sufficient to cause reaction to occur. In the preferred embodiment the ratio of cyanide salt to Ti should be at least 2 which results in the major Ti-containing product being TiN rather than sodium titanium phosphate byproducts. The process is an improvement over prior processes since the byproducts are water soluble salts of sodium which can easily be removed from the preferred TiN product by washing. 2 tabs.

Management of Sodium-reduced Meals at Worksite Cafeterias: Perceptions, Practices, Barriers, and Needs among Food Service Personnel

PubMed Central

Lee, Jounghee; Park, Sohyun

2015-01-01

Objectives The sodium content of meals provided at worksite cafeterias is greater than the sodium content of restaurant meals and home meals. The objective of this study was to assess the relationships between sodium-reduction practices, barriers, and perceptions among food service personnel. Methods We implemented a cross-sectional study by collecting data on perceptions, practices, barriers, and needs regarding sodium-reduced meals at 17 worksite cafeterias in South Korea. We implemented Chi-square tests and analysis of variance for statistical analysis. For post hoc testing, we used Bonferroni tests; when variances were unequal, we used Dunnett T3 tests. Results This study involved 104 individuals employed at the worksite cafeterias, comprised of 35 men and 69 women. Most of the participants had relatively high levels of perception regarding the importance of sodium reduction (very important, 51.0%; moderately important, 27.9%). Sodium reduction practices were higher, but perceived barriers appeared to be lower in participants with high-level perception of sodium-reduced meal provision. The results of the needs assessment revealed that the participants wanted to have more active education programs targeting the general population. The biggest barriers to providing sodium-reduced meals were use of processed foods and limited methods of sodium-reduced cooking in worksite cafeterias. Conclusion To make the provision of sodium-reduced meals at worksite cafeterias more successful and sustainable, we suggest implementing more active education programs targeting the general population, developing sodium-reduced cooking methods, and developing sodium-reduced processed foods. PMID:27169011

Borohydride Reduction of Estrone: Demonstration of Diastereoselectivity in the Undergraduate Organic Chemistry Laboratory

ERIC Educational Resources Information Center

Aditya, Animesh; Nichols, David E.; Loudon, G. Marc

2008-01-01

This experiment presents a guided-inquiry approach to the demonstration of diastereoselectivity in an undergraduate organic chemistry laboratory. Chiral hindered ketones such as estrone, undergo facile reduction with sodium borohydride in a highly diastereoselective manner. The diastereomeric estradiols produced in the reaction can be analyzed and…

A FACILE ONE-POT SYNTHESIS OF β-KETO SULFONES FROM KETONES UNDER SOLVENT-FREE CONDITIONS

EPA Science Inventory

An easy solvent-free method is described for the conversion of ketones into β-keto sulfones in high yields that involves in situ generation of α-tosyloxyketones followed by nucleophilic substitution with sodium arene sulfinate in presence of tetra-butylammonium bromide at ...

Chlorination. Training Module 2.300.2.77.

ERIC Educational Resources Information Center

Kirkwood Community Coll., Cedar Rapids, IA.

This document is an instructional module package prepared in objective form for use by an instructor familiar with chlorine, the reasons for chlorination and safe operation and maintenance of gas chlorine, dry calcium hypochlorite and liquid sodium hypochlorite chlorination systems for water supply and wastewater treatment facilities. Included are…

Bio-based barium alginate film: Preparation, flame retardancy and thermal degradation behavior.

PubMed

Liu, Yun; Zhang, Chuan-Jie; Zhao, Jin-Chao; Guo, Yi; Zhu, Ping; Wang, De-Yi

2016-03-30

A bio-based barium alginate film was prepared via a facile ionic exchange and casting approach. Its flammability, thermal degradation and pyrolysis behaviors, thermal degradation mechanism were studied systemically by limiting oxygen index (LOI), vertical burning (UL-94), microscale combustion calorimetry (MCC), thermogravimetric analysis (TGA) coupled with Fourier transform infrared analysis (FTIR) and pyrolysis-gas chromatography-mass spectrometry (Py-GC-MS). It showed that barium alginate film had much higher LOI value (52.0%) than that of sodium alginate film (24.5%). Moreover, barium alginate film passed the UL-94 V-0 rating, while the sodium alginate film showed no classification. Importantly, peak of heat release rate (PHRR) of barium alginate film in MCC test was much lower than that of sodium alginate film, suggested that introduction of barium ion into alginate film significantly decreased release of combustible gases. TG-FTIR and Py-GC-MS results indicated that barium alginate produced much less flammable products than that of sodium alginate in whole thermal degradation procedure. Finally, a possible degradation mechanism of barium alginate had been proposed. Copyright © 2015 Elsevier Ltd. All rights reserved.

L-lactic acid and sodium p-toluenesulfonate co-doped polypyrrole for high performance cathode in sodium ion battery

NASA Astrophysics Data System (ADS)

Liao, Qishu; Hou, Hongying; Liu, Xianxi; Yao, Yuan; Dai, Zhipeng; Yu, Chengyi; Li, Dongdong

2018-04-01

In this work, polypyrrole (PPy) was co-doped with L-lactic acid (LA) and sodium p-toluenesulfonate (TsONa) for high performance cathode in sodium ion battery (SIB) via facile one-step electropolymerization on Fe foil. The as-synthesized LA/TsONa co-doped PPy cathode was investigated in terms of scanning electron microscope (SEM), Fourier transform infrared spectroscopy (FTIR), galvanostatic charge/discharge and cyclic voltammetry (CV). The results suggested that some oval-bud-like LA/TsONa co-doped PPy particles did form and tightly combine with the surface of Fe foil; furthermore, LA/TsONa co-doped PPy cathode also delivered higher electrochemical performances than TsONa mono-doped PPy cathode. For example, the initial specific discharge capacity was as high as about 124 mAh/g, and the reversible specific capacity still maintained at about 110 mAh/g even after 50 cycles, higher than those of TsONa mono-doped PPy cathode. The synergy effect of multi components of LA/TsONa co-doped PPy cathode should be responsible for high electrochemical performances.

Sodium-Rich Ferric Pyrophosphate Cathode for Stationary Room-Temperature Sodium-Ion Batteries.

PubMed

Shen, Bolei; Xu, Maowen; Niu, Yubin; Han, Jin; Lu, Shiyu; Jiang, Jian; Li, Yi; Dai, Chunlong; Hu, Linyu; Li, Changming

2018-01-10

In this article, carbon-coated Na 3.64 Fe 2.18 (P 2 O 7 ) 2 nanoparticles (∼10 nm) were successfully synthesized via a facile sol-gel method and employed as cathode materials for sodium-ion batteries. The results show that the carbon-coated Na 3.64 Fe 2.18 (P 2 O 7 ) 2 cathode delivers a high reversible capacity of 99 mAh g -1 at 0.2 C, outstanding cycling life retention of 96%, and high Coulomb efficiency of almost 100% even after 1000 cycles at 10 C. Furthermore, the electrochemical performances of full batteries consisting of carbon-coated Na 3.64 Fe 2.18 (P 2 O 7 ) 2 nanoparticles as the cathode and commercialized hard carbon as the anode are tested. The full batteries exhibit a reversible capacity of 86 mAh g -1 at 0.5 C and capacity retention of 80% after 100 cycles. Therefore, the above-mentioned cathode is a potential candidate for developing inexpensive sodium-ion batteries in large-scale energy storage with long life.

Three-Dimensional SnS Decorated Carbon Nano-Networks as Anode Materials for Lithium and Sodium Ion Batteries.

PubMed

Zhou, Yanli; Wang, Qi; Zhu, Xiaotao; Jiang, Fuyi

2018-02-28

The three-dimensional (3D) SnS decorated carbon nano-networks (SnS@C) were synthesized via a facile two-step method of freeze-drying combined with post-heat treatment. The lithium and sodium storage performances of above composites acting as anode materials were investigated. As anode materials for lithium ion batteries, a high reversible capacity of 780 mAh·g -1 for SnS@C composites can be obtained at 100 mA·g -1 after 100 cycles. Even cycled at a high current density of 2 A·g -1 , the reversible capacity of this composite can be maintained at 610 mAh·g -1 after 1000 cycles. The initial charge capacity for sodium ion batteries can reach 333 mAh·g -1 , and it retains a reversible capacity of 186 mAh·g -1 at 100 mA·g -1 after 100 cycles. The good lithium or sodium storage performances are likely attributed to the synergistic effects of the conductive carbon nano-networks and small SnS nanoparticles.

A rapid microwave-assisted synthesis of a sodium-cadmium metal-organic framework having improved performance as a CO2 adsorbent for CCS.

PubMed

Palomino Cabello, Carlos; Arean, Carlos Otero; Parra, José B; Ania, Conchi O; Rumori, P; Turnes Palomino, G

2015-06-07

We report on a facile and rapid microwave-assisted method for preparing a sodium-cadmium metal-organic framework (having coordinatively unsaturated sodium ions) that considerably shortens the conventional synthesis time from 5 days to 1 hour. The obtained (Na,Cd)-MOF showed an excellent volumetric CO2 adsorption capacity (5.2 mmol cm(-3) at 298 K and 1 bar) and better CO2 adsorption properties than those shown by the same metal-organic framework when synthesized following a more conventional procedure. Moreover, the newly prepared material was found to display high selectivity for adsorption of carbon dioxide over nitrogen, and good regenerability and stability during repeated CO2 adsorption-desorption cycles, which are the required properties for any adsorbent intended for carbon dioxide capture and sequestration (CSS) from the post-combustion flue gas of fossil fuelled power stations.

Investigation of the effects of NaOH dopant level on the physical and mechanical properties of carbon/phenolic composite material

NASA Technical Reports Server (NTRS)

Clinton, R. G., Jr.

1985-01-01

The near-catastrophic erosion of the STS-8A solid rocket booster nozzle was the instigating factor in the recent, and on-going, intensive investigation of carbon/phenolic composite materials. Much of this effort has been focused on the effect of sodium contamination on the carbon fibers. It is known that sodium acts as a catalyst in the oxidation of the fibers at elevated temperatures. A study was undertaken to determine what changes were caused by variation in sodium content. Investigations were conducted in three areas: (1) phenolic resin; (2) carbon/phenolic prepreg; and (3) cured laminates. Due to the exploratory nature of the studies, a variety of tests in addition to those normally run in production facilities were considered. The experimental methodologies and results of these experiments are discussed, and recommendations for improving techniques and extending the research program are presented.

Overview of the Madison Dynamo Experiment

NASA Astrophysics Data System (ADS)

Kendrick, R. D.; Spence, E. J.; Nornberg, M. D.; Jacobson, C. M.; Parada, C. A.; Forest, C. B.

2006-10-01

A spherical dynamo experiment has been constructed at the University of Wisconsin-Madison's liquid-sodium facility. The experiment is designed to self-generate magnetic fields from flows of conducting metal. The apparatus consists of a 1 m diameter, spherical stainless steel vessel filled with liquid sodium. Two 100 Hp motors drive impellers which generate the flow. The motors have been operated up to 1300 RPM (70% of design specification), achieving a magnetic Reynolds number of 130, based on impeller tip speed. Various polarizations of external magnetic fields have been applied to the sodium, and the induced magnetic field has been measured by both internal and external Hall probe arrays. The voltage induced across the sphere by the turbulent flow has been measured. Techniques for using ultrasound Doppler velocimetry have been explored in the water model of the experiment, including the use of high-pressure bubbles as seed particles.

Experimental operation of a sodium heat pipe

NASA Astrophysics Data System (ADS)

Holtz, R. E.; McLennan, G. A.; Koehl, E. R.

1985-05-01

This report documents the operation of a 28 in. long sodium heat pipe in the Heat Pipe Test Facility (HPTF) installed at Argonne National Laboratory. Experimental data were collected to simulate conditions prototypic of both a fluidized bed coal combustor application and a space environment application. Both sets of experiment data show good agreement with the heat pipe analytical model. The heat transfer performance of the heat pipe proved reliable over a substantial period of operation and over much thermal cycling. Additional testing of longer heat pipes under controlled laboratory conditions will be necessary to determine performance limitations and to complete the design code validation.

Mechanisms of tubular sodium chloride transport.

PubMed

Venkatesh, S; Schrier, R W; Andreoli, T E

1998-11-01

Extracellular fluid volume is determined by sodium and its accompanying anions. There are control mechanisms which regulate sodium balance in the body. These include high and low pressure baroreceptors, intrarenal baroreceptors, renal autoregulation, tubuloglomerular feedback, aldosterone, and numerous other physical and hormonal factors. Sodium transport by the nephron involves active and passive processes which occur in several different nephron segments. Mechanisms of cotransport, Na(+)-H+ exchange, antiporters and ion-specific channels are all utilized by the nephron to maintain sodium balance. These regulatory factors and transport mechanisms for sodium in the kidney will he discussed in detail.

Combustion system processes leading to corrosive deposits

NASA Technical Reports Server (NTRS)

Stearns, C. A.; Kohl, F. J.; Rosner, D. E.

1981-01-01

Degradation of turbine engine hot gas path components by high temperature corrosion can usually be associated with deposits even though other factors may also play a significant role. The origins of the corrosive deposits are traceable to chemical reactions which take place during the combustion process. In the case of hot corrosion/sulfidation, sodium sulfate was established as the deposited corrosive agent even when none of this salt enters the engine directly. The sodium sulfate is formed during the combustion and deposition processes from compounds of sulfur contained in the fuel as low level impurities and sodium compounds, such as sodium chloride, ingested with intake air. In other turbine and power generation situations, corrosive and/or fouling deposits can result from such metals as potassium, iron, calcium, vanadium, magnesium, and silicon.

Alternative sanitization methods for minimally processed lettuce in comparison to sodium hypochlorite

PubMed Central

Bachelli, Mara Lígia Biazotto; Amaral, Rívia Darla Álvares; Benedetti, Benedito Carlos

2013-01-01

Lettuce is a leafy vegetable widely used in industry for minimally processed products, in which the step of sanitization is the crucial moment for ensuring a safe food for consumption. Chlorinated compounds, mainly sodium hypochlorite, are the most used in Brazil, but the formation of trihalomethanes from this sanitizer is a drawback. Then, the search for alternative methods to sodium hypochlorite has been emerging as a matter of great interest. The suitability of chlorine dioxide (60 mg L−1/10 min), peracetic acid (100 mg L−1/15 min) and ozonated water (1.2 mg L−1 /1 min) as alternative sanitizers to sodium hypochlorite (150 mg L−1 free chlorine/15 min) were evaluated. Minimally processed lettuce washed with tap water for 1 min was used as a control. Microbiological analyses were performed in triplicate, before and after sanitization, and at 3, 6, 9 and 12 days of storage at 2 ± 1 °C with the product packaged on LDPE bags of 60 μm. It was evaluated total coliforms, Escherichia coli, Salmonella spp., psicrotrophic and mesophilic bacteria, yeasts and molds. All samples of minimally processed lettuce showed absence of E. coli and Salmonella spp. The treatments of chlorine dioxide, peracetic acid and ozonated water promoted reduction of 2.5, 1.1 and 0.7 log cycle, respectively, on count of microbial load of minimally processed product and can be used as substitutes for sodium hypochlorite. These alternative compounds promoted a shelf-life of six days to minimally processed lettuce, while the shelf-life with sodium hypochlorite was 12 days. PMID:24516433

Alternative sanitization methods for minimally processed lettuce in comparison to sodium hypochlorite.

PubMed

Bachelli, Mara Lígia Biazotto; Amaral, Rívia Darla Álvares; Benedetti, Benedito Carlos

2013-01-01

Lettuce is a leafy vegetable widely used in industry for minimally processed products, in which the step of sanitization is the crucial moment for ensuring a safe food for consumption. Chlorinated compounds, mainly sodium hypochlorite, are the most used in Brazil, but the formation of trihalomethanes from this sanitizer is a drawback. Then, the search for alternative methods to sodium hypochlorite has been emerging as a matter of great interest. The suitability of chlorine dioxide (60 mg L(-1)/10 min), peracetic acid (100 mg L(-1)/15 min) and ozonated water (1.2 mg L(-1)/1 min) as alternative sanitizers to sodium hypochlorite (150 mg L(-1) free chlorine/15 min) were evaluated. Minimally processed lettuce washed with tap water for 1 min was used as a control. Microbiological analyses were performed in triplicate, before and after sanitization, and at 3, 6, 9 and 12 days of storage at 2 ± 1 °C with the product packaged on LDPE bags of 60 μm. It was evaluated total coliforms, Escherichia coli, Salmonella spp., psicrotrophic and mesophilic bacteria, yeasts and molds. All samples of minimally processed lettuce showed absence of E. coli and Salmonella spp. The treatments of chlorine dioxide, peracetic acid and ozonated water promoted reduction of 2.5, 1.1 and 0.7 log cycle, respectively, on count of microbial load of minimally processed product and can be used as substitutes for sodium hypochlorite. These alternative compounds promoted a shelf-life of six days to minimally processed lettuce, while the shelf-life with sodium hypochlorite was 12 days.

Innovative technologies on fuel assemblies cleaning for sodium fast reactors: First considerations on cleaning process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Simon, N.; Lorcet, H.; Beauchamp, F.

2012-07-01

Within the framework of Sodium Fast Reactor development, innovative fuel assembly cleaning operations are investigated to meet the GEN IV goals of safety and of process development. One of the challenges is to mitigate the Sodium Water Reaction currently used in these processes. The potential applications of aqueous solutions of mineral salts (including the possibility of using redox chemical reactions) to mitigate the Sodium Water Reaction are considered in a first part and a new experimental bench, dedicated to this study, is described. Anhydrous alternative options based on Na/CO{sub 2} interaction are also presented. Then, in a second part, amore » functional study conducted on the cleaning pit is proposed. Based on experimental feedback, some calculations are carried out to estimate the sodium inventory on the fuel elements, and physical methods like hot inert gas sweeping to reduce this inventory are also presented. Finally, the implementation of these innovative solutions in cleaning pits is studied in regard to the expected performances. (authors)« less

Sodium citrate-assisted anion exchange strategy for construction of Bi{sub 2}O{sub 2}CO{sub 3}/BiOI photocatalysts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Song, Peng-Yuan; Xu, Ming; Zhang, Wei-De, E-mail: zhangwd@scut.edu.cn

Highlights: • Heterostructured Bi{sub 2}O{sub 2}CO{sub 3}/BiOI microspheres were prepared via anion exchange. • Sodium citrate-assisted anion exchange for construction of composite photocatalysts. • Bi{sub 2}O{sub 2}CO{sub 3}/BiOI composites show high visible light photocatalytic activity. - Abstract: Bi{sub 2}O{sub 2}CO{sub 3}/BiOI heterojuncted photocatalysts were constructed through a facile partial anion exchange strategy starting from BiOI microspheres and urea with the assistance of sodium citrate. The content of Bi{sub 2}O{sub 2}CO{sub 3} in the catalysts was regulated by modulating the amount of urea as a precursor, which was decomposed to generate CO{sub 3}{sup 2−} in the hydrothermal process. Citrate anion playsmore » a key role in controlling the morphology and composition of the products. The Bi{sub 2}O{sub 2}CO{sub 3}/BiOI catalysts display much higher photocatalytic activity than pure BiOI and Bi{sub 2}O{sub 2}CO{sub 3} towards the degradation of rhodamine B (RhB) and bisphenol A (BPA). The enhancement of photocatalytic activity of the heterojuncted catalysts is attributed to the formation of p–n junction between p-BiOI and n-Bi{sub 2}O{sub 2}CO{sub 3}, which is favorable for retarding the recombination of photoinduced electron-hole pairs. Moreover, the holes are demonstrated to be the main active species for the degradation of RhB and BPA.« less

[Subtype classification of ceftriaxone sodium and its influence on the quality of product].

PubMed

Xue, Jing; Jia, Yan-Hua; Li, Jin; Yin, Li-Hui; Hu, Chang-Qin

2014-07-01

Powder X-ray diffraction (PXRD) technology combined with cluster analysis method was used to classify 75 batches of crystalline ceftriaxone sodium into subtypes, the crystalline characteristics of each subtype were measured with scanning electron microscope (SEM). By comparing some parameters of these subtypes correlated to crystallization process of ceftriaxone sodium, such as salification rate, water content in different subtypes, as well as by studying different lattice stabilities, different compatibilities with rubber closures during accelerated stability tests, the key point to improve the quality of domestic ceftriaxone sodium was disclosed. The results of this paper indicated that the fine structure of the products could be controlled well by improving the salification and crystallization process. As a result, the subtype II of ceftriaxone sodium with high stability can be produced.

Sodium Reduction in Processed Foods in Brazil: Analysis of Food Categories and Voluntary Targets from 2011 to 2017

PubMed Central

Silva, Sara A.; L’Abbé, Mary; Jaime, Patricia C.

2017-01-01

Non-communicable diseases, including cardiovascular diseases, are responsible for over 70% of deaths in Brazil. Currently, over 25% of Brazilian adults are diagnosed as hypertensive; overall, current dietary sodium intake in Brazil (4700 mg/person) is over twice the international recommendations, and 70–90% of adolescents and adults consume excessive sodium. National sodium reduction strategies consider the main dietary sources of sodium to be added salt to foods, foods consumed outside of the household, and sodium in processed foods. The national voluntary strategy for sodium reduction in priority food categories has been continuously monitored over a 6-year period (2011–2017) and there was a significant 8–34% reduction in the average sodium content of over half food categories. Different food categories have undergone differing reductions in sodium over time, aiding gradual biannual targets to allow industries to develop new technologies and consumers to adapt to foods with less salt. By 2017, most products of all food categories had met the regional targets proposed by the Pan American Health Organization, showing that voluntary sodium reduction strategies can potentially contribute to food reformulation. Nevertheless, regulatory approaches may still be necessary in the future in order to reach all food producers and to allow stronger enforcement to meet more stringent regional targets. PMID:28704932

Criticality safety strategy and analysis summary for the fuel cycle facility electrorefiner at Argonne National Laboratory West

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mariani, R.D.; Benedict, R.W.; Lell, R.M.

1996-05-01

As part of the termination activities of Experimental Breeder Reactor II (EBR-II) at Argonne National Laboratory (ANL) West, the spent metallic fuel from EBR-II will be treated in the fuel cycle facility (FCF). A key component of the spent-fuel treatment process in the FCF is the electrorefiner (ER) in which the actinide metals are separated from the active metal fission products and the reactive bond sodium. In the electrorefining process, the metal fuel is anodically dissolved into a high-temperature molten salt, and refined uranium or uranium/plutonium products are deposited at cathodes. The criticality safety strategy and analysis for the ANLmore » West FCF ER is summarized. The FCF ER operations and processes formed the basis for evaluating criticality safety and control during actinide metal fuel refining. To show criticality safety for the FCF ER, the reference operating conditions for the ER had to be defined. Normal operating envelopes (NOEs) were then defined to bracket the important operating conditions. To keep the operating conditions within their NOEs, process controls were identified that can be used to regulate the actinide forms and content within the ER. A series of operational checks were developed for each operation that will verify the extent or success of an operation. The criticality analysis considered the ER operating conditions at their NOE values as the point of departure for credible and incredible failure modes. As a result of the analysis, FCF ER operations were found to be safe with respect to criticality.« less

LITERATURE REVIEW OF BORIC ACID SOLUBILITY DATA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crapse, K.; Kyser, E.

2011-09-22

A new solvent system is being evaluated for use in the Modular Caustic-Side Solvent Extraction Unit (MCU) and in the Salt Waste Processing Facility (SWPF). The new system replaces the current dilute nitric acid strip solution with 0.01 M boric acid. This literature study is performed to determine if there is a potential for boric acid to crystallize in the lines with emphasis on the transfer lines to the Defense Waste Processing Facility. This report focuses on the aqueous phase chemistry of boric acid under conditions relevant to MCU and SWPF. Operating and transfer conditions examined for the purpose ofmore » this review include temperatures between 13 C (McLeskey, 2008) and 45 C (Fondeur, 2007) and concentrations from 0 to 3M in nitric acid as well as exposure of small amounts of entrained boric acid in the organic phase to the sodium hydroxide caustic wash stream. Experiments were also conducted to observe any chemical reactions and off-gas generation that could occur when 0.01 M boric acid solution mixes with 3 M nitric acid solution and vice versa. Based on the low concentration (0.01M) of boric acid in the MCU/SWPF strip acid and the moderate operating temperatures (13 C to 45 C), it is unlikely that crystallization of boric acid will occur in the acid strip solution under process or transfer conditions. Mixing experiments of boric and nitric acid show no measurable gas generation (< 1 cc of gas per liter of solution) under similar process conditions.« less

Scalable and sustainable synthesis of carbon microspheres via a purification-free strategy for sodium-ion capacitors

NASA Astrophysics Data System (ADS)

Wang, Shijie; Wang, Rutao; Zhang, Yabin; Jin, Dongdong; Zhang, Li

2018-03-01

Sodium-based energy storage receives a great deal of interest due to the virtually inexhaustible sodium reserve, while the scalable and sustainable strategies to synthesize carbon-based materials with suitable interlayer spaces and large sodium storage capacities are yet to be fully investigated. Carbon microspheres, with regular geometry, non-graphitic characteristic, and stable nature are promising candidates, yet the synthetic methods are usually complex and energy consuming. In this regard, we report a scalable purification-free strategy to synthesize carbon microspheres directly from 5 species of fresh juice. As-synthesized carbon microspheres exhibit dilated interlayer distance of 0.375 nm and facilitate Na+ uptake and release. For example, such carbon microsphere anodes have a specific capacity of 183.9 mAh g-1 at 50 mA g-1 and exhibit ultra-stability (99.0% capacity retention) after 10000 cycles. Moreover, via facile activation, highly porous carbon microsphere cathodes are fabricated and show much higher energy density at high rate than commercial activated carbon. Coupling the compelling anodes and cathodes above, novel sodium-ion capacitors show the high working potential up to 4.0 V, deliver a maximum energy density of 52.2 Wh kg-1, and exhibit an acceptable capacity retention of 85.7% after 2000 cycles.

Well-ordered mesoporous Fe2O3/C composites as high performance anode materials for sodium-ion batteries.

PubMed

Li, Mei; Ma, Chao; Zhu, Qian-Cheng; Xu, Shu-Mao; Wei, Xiao; Wu, Yong-Min; Tang, Wei-Ping; Wang, Kai-Xue; Chen, Jie-Sheng

2017-04-11

Sodium-ion batteries have attracted considerable attention in recent years. In order to promote the practical application of sodium-ion batteries, the electrochemical performances, such as specific capacity, reversibility, and rate capability of the anode materials, should be further improved. In this work, a Fe 2 O 3 /C composite with a well-ordered mesoporous structure is prepared via a facile co-impregnation method by using mesoporous silica SBA-15 as a hard template. When used as an anode material for sodium-ion batteries, the well-ordered mesoporous structure ensures fast mass transport kinetics. The presence of nano-sized Fe 2 O 3 particles confined within the carbon walls significantly enhances the specific capacity of the composite. The carbon walls in the composite act not only as an active material contributing to the specific capacity, but also as a conductive matrix improving the cycling stability of Fe 2 O 3 nanoparticles. As a result, the well-ordered mesoporous Fe 2 O 3 /C composite exhibits high specific capacity, excellent cycleability, and high rate capability. It is proposed that this simple co-impregnation method is applicable for the preparation of well-ordered mesoporous transition oxide/carbon composite electrode materials for high performance sodium-ion and lithium-ion batteries.

Comparative studies on osmosis based encapsulation of sodium diclofenac in porcine and outdated human erythrocyte ghosts.

PubMed

Bukara, Katarina; Drvenica, Ivana; Ilić, Vesna; Stančić, Ana; Mišić, Danijela; Vasić, Borislav; Gajić, Radoš; Vučetić, Dušan; Kiekens, Filip; Bugarski, Branko

2016-12-20

The objective of our study was to develop controlled drug delivery system based on erythrocyte ghosts for amphiphilic compound sodium diclofenac considering the differences between erythrocytes derived from two readily available materials - porcine slaughterhouse and outdated transfusion human blood. Starting erythrocytes, empty erythrocyte ghosts and diclofenac loaded ghosts were compared in terms of the encapsulation efficiency, drug releasing profiles, size distribution, surface charge, conductivity, surface roughness and morphology. The encapsulation of sodium diclofenac was performed by an osmosis based process - gradual hemolysis. During this process sodium diclofenac exerted mild and delayed antihemolytic effect and increased potassium efflux in porcine but not in outdated human erythrocytes. FTIR spectra revealed lack of any membrane lipid disorder and chemical reaction with sodium diclofenac in encapsulated ghosts. Outdated human erythrocyte ghosts with detected nanoscale damages and reduced ability to shrink had encapsulation efficiency of only 8%. On the other hand, porcine erythrocyte ghosts had encapsulation efficiency of 37% and relatively slow drug release rate. More preserved structure and functional properties of porcine erythrocytes related to their superior encapsulation and release performances, define them as more appropriate for the usage in sodium diclofenac encapsulation process. Copyright © 2016 Elsevier B.V. All rights reserved.

Pilot scale-SO{sub 2} control by dry sodium bicarbonate injection and an electrostatic precipitator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pliat, M.J.; Wilder, J.M.

2007-10-15

A 500 actual cubic feet gas per minute (acfm) pilot-scale SO{sub 2} control study was undertaken to investigate flue gas desulfurization (FGD) by dry sodium sorbents in 400{sup o}F (204.5{sup o}C) flue gases emitted from a coal fired boiler with flue gas concentrations between 350 and 2500 ppm SO{sub 2}. Powdered sodium alkaline reagents were injected into the hot flue gas downstream of the air preheater and the spent reagents were collected using an electrostatic precipitator. Three different sorbents were used: processed sodium bicarbonate of two particle sizes; solution mined sodium bicarbonate, and processed sodium sesquicarbonate. SO{sub 2} concentrations weremore » measured upstream of the reagent injection, 25-ft (7.62 m) downstream of the injection point, and downstream of the electrostatic precipitator. SO{sub 2} collection efficiencies ranged from 40 to 80% using sodium bicarbonate stoichiometric ratios from 0.5 to 3.0. Much of the in-duct SO{sub 2} removal occurred during the first second of reagent reaction time, indicating that the sulfur dioxide-sodium reaction rates may be faster than have been measured for fixed bed measurements reported in the literature.« less

The Mechanism of Sodium and Chloride Uptake by the Gills of a Fresh-Water Fish, Carassius auratus

PubMed Central

García Romeu, F.; Maetz, J.

1964-01-01

Carassius auratus placed in a dilute sodium chloride solution (400 µM) is able to absorb sodium and chloride ions at very different rates, or to absorb one ion and to lose the other. This is the case not only for fish which have been previously kept in choline chloride or sodium sulfate solutions or deionized water, in order to stimulate their absorption processes, but also in control fish which have not been deprived of sodium or chloride. The absorption of sodium or chloride appears to be unaffected by the presence of a nonpermeant co-ion such as choline or sulfate. Conductivity measurements of the external medium show that during ion uptake the conductivity is constant or increases slowly. This suggests the existence of exchange processes between the ions absorbed and endogenous ions excreted. It is unlikely that potassium or calcium is exchanged for sodium, because of the low permeability of the gills to these ions. Finally, the flux ratios observed for both sodium and chloride ions in the present investigation can only be explained, in relation to their electrochemical gradients across the gills, in terms of active transport. PMID:14192553

Salt balance: From space experiments to revolutionizing new clinical concepts on earth - A historical review

NASA Astrophysics Data System (ADS)

Gerzer, Rupert

2014-11-01

For a long time, sodium balance appeared to be a ;done deal; and was thought to be well understood. However, experiments in preparation of space missions showed that the concept of osmotic sodium storage and close correlations of sodium with water balance are only part of the regulatory mechanisms of body salt. By now it has turned out that the human skin is an important storage place and regulator for sodium, that sodium storage involves macrophages which in turn salt-dependently co-regulate blood pressure, that body sodium also strongly influences bone and protein metabolism, and that immune functions are also strongly influenced by sodium. In addition, the aging process appears to lead to increased body sodium storage, which in turn might influence the aging process of the human body. The current review article summarizes the developments that have led to these revolutionizing new findings and concepts as well as consequences deriving from these findings. Therefore, it is not intended in this article to give a complete literature overview over the whole field but to focus on such key literature and considerations that led to the respective developments.

The effectiveness of sodium hydroxide (NaOH) and sodium carbonate (Na2CO3) on the impurities removal of saturated salt solution

NASA Astrophysics Data System (ADS)

Pujiastuti, C.; Ngatilah, Y.; Sumada, K.; Muljani, S.

2018-01-01

Increasing the quality of salt can be done through various methods such as washing (hydro-extraction), re-crystallization, ion exchange methods and others. In the process of salt quality improvement by re-crystallization method where salt product diluted with water to form saturated solution and re-crystallized through heating process. The quality of the salt produced is influenced by the quality of the dissolved salt and the crystallization mechanism applied. In this research is proposed a concept that before the saturated salt solution is recrystallized added a chemical for removal of the impurities such as magnesium ion (Mg), calcium (Ca), potassium (K) and sulfate (SO4) is contained in a saturated salt solution. The chemical reagents that used are sodium hydroxide (NaOH) 2 N and sodium carbonate (Na2CO3) 2 N. This research aims to study effectiveness of sodium hydroxide and sodium carbonate on the impurities removal of magnesium (Mg), calcium (Ca), potassium (K) and sulfate (SO4). The results showed that the addition of sodium hydroxide solution can be decreased the impurity ions of magnesium (Mg) 95.2%, calcium ion (Ca) 45%, while the addition of sodium carbonate solution can decreased magnesium ion (Mg) 66.67% and calcium ion (Ca) 77.5%, but both types of materials are not degradable sulfate ions (SO4). The sodium hydroxide solution more effective to decrease magnesium ion than sodium carbonate solution, and the sodium carbonate solution more effective to decrease calcium ion than sodium hydroxide solution.

Feasibility of processing the experimental breeder reactor-II driver fuel from the Idaho National Laboratory through Savannah River Site's H-Canyon facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Magoulas, V. E.

Savannah River National Laboratory (SRNL) was requested to evaluate the potential to receive and process the Idaho National Laboratory (INL) uranium (U) recovered from the Experimental Breeder Reactor II (EBR-II) driver fuel through the Savannah River Site’s (SRS) H-Canyon as a way to disposition the material. INL recovers the uranium from the sodium bonded metallic fuel irradiated in the EBR-II reactor using an electrorefining process. There were two compositions of EBR-II driver fuel. The early generation fuel was U-5Fs, which consisted of 95% U metal alloyed with 5% noble metal elements “fissium” (2.5% molybdenum, 2.0% ruthenium, 0.3% rhodium, 0.1% palladium,more » and 0.1% zirconium), while the later generation was U-10Zr which was 90% U metal alloyed with 10% zirconium. A potential concern during the H-Canyon nitric acid dissolution process of the U metal containing zirconium (Zr) is the explosive behavior that has been reported for alloys of these materials. For this reason, this evaluation was focused on the ability to process the lower Zr content materials, the U-5Fs material.« less

Fabrication Of Metal Chloride Cathodes By Sintering

NASA Technical Reports Server (NTRS)

Bugga, Ratnakumar V.; Di Stefano, Salvador; Bankston, C. Perry

1992-01-01

Transition-metal chloride cathodes for use in high-temperature rechargeable sodium batteries prepared by sintering transition-metal powders mixed with sodium chloride. Need for difficult and dangerous chlorination process eliminated. Proportions of transition metal and sodium chloride in mixture adjusted to suit specific requirements. Cathodes integral to sodium/metal-chloride batteries, which have advantages over sodium/sulfur batteries including energy densities, increased safety, reduced material and thermal-management problems, and ease of operation and assembly. Being evaluated for supplying electrical power during peak demand and electric vehicles.

The Distant Sodium Tail of Mercury

NASA Technical Reports Server (NTRS)

Potter, A. E.; Killen, R. M.; Morgan, T. H.

2001-01-01

Models of the sodium atmosphere of Mercury predict the possible existence of a cornet-like sodium tail. Detection and mapping of the predicted sodium tail would provide quantitative data on the energy of the process that produces sodium atoms from the planetary surface. Previous efforts to detect the sodium tail by means of observations done during daylight hours have been only partially successful because scattered sunlight obscured the weak sodium emissions in the tail. However, at greatest eastern elongation around the March equinox in the northern hemisphere, Mercury can be seen as an evening star in astronomical twilight. At this time, the intensity of scattered sunlight is low enough that sodium emissions as low as 500 Rayleighs can be detected. Additional information is contained in the original extended abstract.

Process for removing polychlorinated and polybrominated biphenyls from oils

DOEpatents

Orlett, M.J.

The invention is a relatively simple and inexpensive process for detoxifying oils contaminated with PCBs and/or PBBs. The process is especially suitable for processing lubricating oils containing such contaminants. In one aspect of the invention, the contaminated lubricating oil is contacted with a particulate reagent comprising adsorbent particles carrying a dispersion of metallic sodium. The solid sodium reagent converts the PCB and/or PBB contaminants to environmentally acceptable products and also converts various sodium-reactive additives normally present in lubricating oil to reaction products. The adsorbent reagent retains most of the products and is easily separated from the detoxified oil. The detoxified oil may be fortified with various additives functionally equivalent to those removed during detoxification.

PROCESSES OF RECOVERING URANIUM FROM A CALUTRON

DOEpatents

Baird, D.O.; Zumwalt, L.R.

1958-07-15

An improved process is described for recovering the residue of a uranium compound which has been subjected to treatment in a calutron, from the parts of the calutron disposed in the source region upon which the residue is deposited. The process may be utilized when the uranium compound adheres to a surface containing metals of the group consisting of copper, iron, chromium, and nickel. The steps comprise washing the surface with an aqueous acidic oxidizing solvent for the uranium whereby there is obtained an acidic aqueous Solution containing uranium as uranyl ions and metals of said group as impurities, treating the acidic solution with sodium acetate in the presenee of added sodium nitrate to precipitate the uranium as sodium uranyl acetate away from the impurities in the solution, and separating the sodium uranyl acetate from the solution.

Development of cement solidification process for sodium borate waste generated from PWR plants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hirofumi Okabe; Tatsuaki Sato; Yuichi Shoji

2013-07-01

A cement solidification process for treating sodium borate waste produced in pressurized water reactor (PWR) plants was studied. To obtain high volume reduction and high mechanical strength of the waste, simulated concentrated borate liquid waste with a sodium / boron (Na/B) mole ratio of 0.27 was dehydrated and powdered by using a wiped film evaporator. To investigate the effect of the Na/B mole ratio on the solidification process, a sodium tetraborate decahydrate reagent with a Na/B mole ratio of 0.5 was also used. Ordinary portland cement (OPC) and some additives were used for the solidification. Solidified cement prepared from powderedmore » waste with a Na/B mole ratio 0.24 and having a high silica sand content (silica sand/cement>2) showed to improved uniaxial compressive strength. (authors)« less

Variation of lunar sodium emission intensity with phase angle

NASA Technical Reports Server (NTRS)

Potter, A. E.; Morgan, T. H.

1994-01-01

We report new measurements of the sodium emission intensity seen in a line of sight just above the surface of the Moon. These data show a strong dependence on lunar phase. The emission intensity decreases from a maximum around first quarter (phase angle 90 deg) to very small values near full Moon (phase angle 0 deg). This suggests that the rate of sodium vapor production from the lunar surface is largest at the subsolar point and becomes small near the terminator. However, the sodium emission near full Moon falls below that which would be expected for solar photon-driven processes. Since the solar wind flux decreases substantially when the Moon enters the Earth's magnetotail near full Moon, while the global solar photon flux is undiminished, we suggest that solar wind sputtering is the dominant process for sodium production.

A facile and regioselective synthesis of 1,4-disubstituted 1,2,3-triazoles using click chemistry

EPA Science Inventory

The reaction of α-tosyloxy ketones, sodium azide and terminal alkynes in presence of copper(I) in aqueous polyethylene glycol afforded regioselectively 1,4-disubstituted 1,2,3-triazoles in good yield at ambient temperature. The one-pot exclusive formation of 1,4-disubstituted 1,2...

GATEWAY Report Brief: SSL Evaluation: Philadelphia International Airport Apron Lighting

DOE Office of Scientific and Technical Information (OSTI.GOV)

None, None

Summary of report that documents a trial installation of LED apron lighting that replaced the existing high-pressure sodium luminaires at Philadelphia International Airport. Such high-mast applications remain challenging for LED technology, and the lessons learned from this project may help facility managers and LED product manufacturers better meet those challenges.

Toward a Mechanistic Source Term in Advanced Reactors: A Review of Past U.S. SFR Incidents, Experiments, and Analyses

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bucknor, Matthew; Brunett, Acacia J.; Grabaskas, David

In 2015, as part of a Regulatory Technology Development Plan (RTDP) effort for sodium-cooled fast reactors (SFRs), Argonne National Laboratory investigated the current state of knowledge of source term development for a metal-fueled, pool-type SFR. This paper provides a summary of past domestic metal-fueled SFR incidents and experiments and highlights information relevant to source term estimations that were gathered as part of the RTDP effort. The incidents described in this paper include fuel pin failures at the Sodium Reactor Experiment (SRE) facility in July of 1959, the Fermi I meltdown that occurred in October of 1966, and the repeated meltingmore » of a fuel element within an experimental capsule at the Experimental Breeder Reactor II (EBR-II) from November 1967 to May 1968. The experiments described in this paper include the Run-Beyond-Cladding-Breach tests that were performed at EBR-II in 1985 and a series of severe transient overpower tests conducted at the Transient Reactor Test Facility (TREAT) in the mid-1980s.« less

Admission sodium level and prognosis in adult Guillain-Barré syndrome.

PubMed

Sipilä, Jussi O T; Kauko, Tommi; Soilu-Hänninen, Merja

2017-04-01

Guillain-Barré syndrome (GBS) varies in severity and outcome. Hyponatremia predicts poor outcome but previous studies have used divergent methodology and (pseudo)hyponatremia caused by intravenous immunoglobulin administration may confound analysis. We studied if the plasma sodium level at admission was associated with GBS outcome. All 69 patients at least 16 years of age treated for GBS in Turku University Hospital in 2004-2013 were included in the study. Clinical information was obtained from patient charts. Women had lower sodium levels at admission (138; IQR 135, 140) compared to men (140; IQR 138, 142; p = 0.0116) but no association of sodium levels with demographics, pre-hospital variables or basic GBS characteristics was found. Multivariate analyses showed lower admission sodium levels to be associated with worse functional status at one year from disease onset (OR 1.37; 95% CI 1.07-1.76; p = 0.0136) and probability of being discharged to another care facility from the hospital (OR 1.31; 95% CI 1.05-1.64; p = 0.0180) but not associated with need of intensive care unit care (p = 0.09) or mechanical ventilation (p = 0.45), length of hospital stay (p =0.48) or functional status at six months (p = 0.07). Low plasma sodium level at admission is associated with a more severe disease course and a worse outcome in GBS independently of previously identified prognostic factors. Hyponatremia does not, however, appear to be caused by disease-specific factors.

Industrial research for transmutation scenarios

NASA Astrophysics Data System (ADS)

Camarcat, Noel; Garzenne, Claude; Le Mer, Joël; Leroyer, Hadrien; Desroches, Estelle; Delbecq, Jean-Michel

2011-04-01

This article presents the results of research scenarios for americium transmutation in a 22nd century French nuclear fleet, using sodium fast breeder reactors. We benchmark the americium transmutation benefits and drawbacks with a reference case consisting of a hypothetical 60 GWe fleet of pure plutonium breeders. The fluxes in the various parts of the cycle (reactors, fabrication plants, reprocessing plants and underground disposals) are calculated using EDF's suite of codes, comparable in capabilities to those of other research facilities. We study underground thermal heat load reduction due to americium partitioning and repository area minimization. We endeavor to estimate the increased technical complexity of surface facilities to handle the americium fluxes in special fuel fabrication plants, americium fast burners, special reprocessing shops, handling equipments and transport casks between those facilities.

Contribution of Food Additives to Sodium and Phosphorus Content of Diets Rich in Processed Foods

PubMed Central

Carrigan, Anna; Klinger, Andrew; Choquette, Suzanne S.; Luzuriaga-McPherson, Alexandra; Bell, Emmy K.; Darnell, Betty; Gutiérrez, Orlando M.

2013-01-01

Objective Phosphorus-based food additives increase total phosphorus content of processed foods. However, the extent to which these additives augment total phosphorus intake per day is unclear. Design, setting, and measurements In order to examine the contribution of phosphorus-based food additives to the total phosphorus content of processed foods, separate four-day menus for a low-additive and additive-enhanced diet were developed using Nutrition Data System for Research (NDSR) software. The low-additive diet was designed to conform to United States Department of Agriculture guidelines for energy and phosphorus intake (~2,000 kcal per day and 900 mg of phosphorus per day) and contained minimally-processed foods. The additive-enhanced diet contained the same food items as the low-additive diet except that highly-processed foods were substituted for minimally-processed foods. Food items from both diets were collected, blended, and sent for measurement of energy and nutrient intake. Results Both the low-additive and additive-enhanced diet provided ~2,200 kcal, 700 mg of calcium and 3,000 mg of potassium per day on average. Measured sodium and phosphorus content standardized per 100 mg of food was higher each day of the additive-enhanced diet as compared to the low-additive. When averaged over the four menu days, measured phosphorus and sodium contents of the additive-enhanced diet were 606 ± 125 and 1,329 ± 642 mg higher than the low-additive diet, respectively, representing a 60% increase in total phosphorus and sodium content on average. When comparing the measured values of the additive-enhanced diet to NDSR-estimated values, there were no statistically significant differences in measured vs. estimated phosphorus contents. Conclusion Phosphorus and sodium additives in processed foods can substantially augment phosphorus and sodium intake, even in relatively healthy diets. Current dietary software may provide reasonable estimates of phosphorus content in processed foods. PMID:24355818

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chassery, A.; Universite de Toulouse, Laboratoire de Genie Chimique, Toulouse; CNRS, Laboratoire de Genie Chimique, Toulouse

Within the framework of the dismantling of fast breeder reactors in France several processes are under investigation regarding sodium disposal. One of them, called ELA (radioactive sodium waste treatment process), is based on the implementation of the sodium-water reaction, in a controlled and progressive way, to remove residual sodium. This sodium contains impurities such as sodium hydride, sodium oxide and tritiated sodium hydride. The hydrolysis of these various chemical species leads to the production of a liquid effluent, mainly composed of an aqueous solution of sodium hydroxide, and a gaseous effluent, mainly composed of nitrogen (inert gas), hydrogen and steam.more » The tritium is distributed between these effluents, and, within the gaseous effluent, according to its forms HT and HTO (tritiated water). HTO being 10,000 times more radio-toxic than HT, a precise knowledge of the mechanisms governing the phase distribution of tritium is necessary. This paper presents the first experimental results from a parametric study on the tritium distribution between the various effluents generated during hydrolysis operations. A series of experiments have been performed in order to study the influence of water flow rate, argon flow rate, initial mass and specific activity of the hydrolyzed sodium sample. An important influence of the total tritium concentration in the hydrolyzed sample has been highlighted. As for the phenomena suspected to be responsible for the phase change of tritiated water, in the studied range of parameters, vaporization induced by the heat of reactions seems to be dominant over the evaporation induced by the inert gas flow rate.« less

Perceived Barriers and Support Strategies for Reducing Sodium Intake in Patients with Chronic Kidney Disease: a Qualitative Study.

PubMed

Meuleman, Yvette; Ten Brinke, Lucia; Kwakernaak, Arjan J; Vogt, Liffert; Rotmans, Joris I; Bos, Willem Jan W; van der Boog, Paul J M; Navis, Gerjan; van Montfrans, Gert A; Hoekstra, Tiny; Dekker, Friedo W; van Dijk, Sandra

2015-08-01

Reducing sodium intake can prevent cardiovascular complications and further decline of kidney function in patients with chronic kidney disease. However, the vast majority of patients fail to reach an adequate sodium intake, and little is known about why they do not succeed. This study aims to identify perceived barriers and support strategies for reducing sodium intake among both patients with chronic kidney disease and health-care professionals. A purposive sample of 25 patients and 23 health-care professionals from 4 Dutch medical centers attended 8 focus groups. Transcripts were analyzed thematically and afterwards organized according to the phases of behavior change of self-regulation theory. Multiple themes emerged across different phases of behavior change, including the patients' lack of practical knowledge and intrinsic motivation, the maladaptive illness perceptions and refusal skills, the lack of social support and feedback regarding disease progression and sodium intake, and the availability of low-sodium foods. The results indicate the need for the implementation of support strategies that target specific needs of patients across the whole process of changing and maintaining a low-sodium diet. Special attention should be paid to supporting patients to set sodium-related goals, strengthening intrinsic motivation, providing comprehensive and practical information (e.g., about hidden salt in products), increasing social support, stimulating the self-monitoring of sodium intake and disease progression, and building a supportive patient-professional relationship that encompasses shared decision making and coaching. Moreover, global programs should be implemented to reduce sodium levels in processed foods, introduce sodium-related product labels, and increase consumer awareness.

Resonance ionization spectroscopy of sodium Rydberg levels using difference frequency generation of high-repetition-rate pulsed Ti:sapphire lasers

NASA Astrophysics Data System (ADS)

Naubereit, P.; Marín-Sáez, J.; Schneider, F.; Hakimi, A.; Franzmann, M.; Kron, T.; Richter, S.; Wendt, K.

2016-05-01

The generation of tunable laser light in the green to orange spectral range has generally been a deficiency of solid-state lasers. Hence, the formalisms of difference frequency generation (DFG) and optical parametric processes are well known, but the DFG of pulsed solid-state lasers was rarely efficient enough for its use in resonance ionization spectroscopy. Difference frequency generation of high-repetition-rate Ti:sapphire lasers was demonstrated for resonance ionization of sodium by efficiently exciting the well-known D1 and D2 lines in the orange spectral range (both ≈589 nm). In order to prove the applicability of the laser system for its use at resonance ionization laser ion sources of radioactive ion beam facilities, the first ionization potential of Na was remeasured by three-step resonance ionization into Rydberg levels and investigating Rydberg convergences. A result of EIP=41449.455 (6) stat(7) syscm-1 was obtained, which is in perfect agreement with the literature value of EIPlit =41449.451(2)cm-1 . A total of 41 level positions for the odd-parity Rydberg series n f 2F5/2,7/2o for principal quantum numbers of 10 ≤n ≤60 were determined experimentally.

Post Retort, Pre Hydro-treat Upgrading of Shale Oil

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gordon, John

Various oil feedstocks, including oil from oil shale, bitumen from tar sands, heavy oil, and refin- ery streams were reacted with the alkali metals lithium or sodium in the presence of hydrogen or methane at elevated temperature and pressure in a reactor. The products were liquids with sub- stantially reduced metals, sulfur and nitrogen content. The API gravity typically increased. Sodi- um was found to be more effective than lithium in effectiveness. The solids formed when sodium was utilized contained sodium sulfide which could be regenerated electrochemically back to so- dium and a sulfur product using a "Nasicon", sodium ionmore » conducting membrane. In addition, the process was found to be effective reducing total acid number (TAN) to zero, dramatically reduc- ing the asphaltene content and vacuum residual fraction in the product liquid. The process has promise as a means of eliminating sulfur oxide and carbon monoxide emissions. The process al- so opens the possibility of eliminating the coking process from upgrading schemes and upgrad- ing without using hydrogen.« less

Single Molecule Imaging of Conformational Dynamics in Sodium-Coupled Transporters

ERIC Educational Resources Information Center

Terry, Daniel S.

2013-01-01

Neurotransmitter:sodium symporter (NSS) proteins remove neurotransmitters released into the synapse through a transport process driven by the physiological sodium ion (Na[superscript +]) gradient. NSSs for dopamine, noradrenaline, and serotonin are targeted by the psychostimulants cocaine and amphetamines, as well as by antidepressants. The…

Synthesis and characterization of zinc-molybdenum oxide photocatalysts using an electrochemical-thermal process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goveas, J. J., E-mail: jenicegoveas@gmail.com; Gonsalves, R. A.; Rao, P.

2016-05-23

Dyes act as major pollutants in water and can be degraded by photocatalysis. This paper establishes the role of electrochemically generated nanostructures of Zinc-Molybdenum oxides (ZMO) as photocatalysts by degrading EBT (Eriochrome Black- T) taken as a model pollutant under UV light. A facile, rapid and low cost process to synthesize these nanostructures (ZMO) is presented. Various factors that affect the synthesis and photocatalytic activity of these nanostructures are discussed. The role of calcination temperature and pulverization on the photocatalytic action has also been established. Particles have been synthesized in pure form as well as using surfactants such as cetrimidemore » (cetyl trimethyl ammonium bromide), polyethylene glycol (PEG) and SDS (sodium dodecyl sulphate) to enhance their photocatalytic action. This paper also discusses the characterization of these nanoparticles by powder XRD, SEM, FT-IR and UV-Visible spectroscopy. Decolourisation was achieved to completion under optimum experimental conditions at room temperature ascertaining the application of these nanostructures as effective photocatalysts.« less

Monodisperse Zn-doped Fe3O4 formation and photo-Fenton activity for degradation of rhodamine B in water

NASA Astrophysics Data System (ADS)

Cen, Huoshi; Nan, Zhaodong

2018-10-01

Zn-doped Fe3O4 can be used as a catalyst in the photo-Fenton process to degrade dye molecules dissolved in water, in which cluster-shaped Zn-doped Fe3O4 (CSZnFe) was synthesized. To enhance the catalytic activity, monodisperse Zn-doped Fe3O4 (MZnFe) was facilely synthesized by a modified solvothermal method through replacement of sodium acetate by urea as a base. The particle size of MZnFe was about 9-16 nm. MZnFe exhibits a larger surface area and higher photo-Fenton catalytic activity for degradation of rhodamine B in water than CSZnFe. Additionally, MZnFe exhibits high saturation magnetization (about 80 emu/g), which is very convenient for separation of MZnFe from solution by a magnet. The growth processes for MZnFe were proposed on the basis of results from in situ calorimetry and other techniques, which indicated different formation mechanisms for MZnFe and CSZnFe.

The impact of high hydrostatic pressure on the functionality and consumer acceptability of reduced sodium naturally cured wieners.

PubMed

Pietrasik, Z; Gaudette, N J; Johnston, S P

2017-07-01

The effects of high pressure processing (HPP; 600MPa for 3min at 8°C) on the quality and shelf life of reduced sodium naturally-cured wieners was studied. HPP did not negatively impact processing characteristics and assisted in extending shelf life of all wiener treatments up to a 12week storage period. At week 8, HPP wieners received higher acceptability scores, indicating HPP can effectively extend the sensory quality of products, including sodium reduced formulations containing natural forms of nitrite. Substitution of 50% NaCl with modified KCl had negative effect on textural characteristics of conventionally cured wieners but not those processed with celery powder as a source of nitrite. Celery powder favorably affected hydration of textural properties of wieners, and consumer acceptability of juiciness and texture was higher compared to nitrite. Sodium reduction, independent of curing agent, negatively impacted flavor acceptability, while only nitrite containing reduced sodium wieners scored significantly lower than both regular salt wieners for texture, juiciness and saltiness. Copyright © 2017 Elsevier Ltd. All rights reserved.

Production of L-lactic acid by a thermophilic Bacillus mutant using sodium hydroxide as neutralizing agent.

PubMed

Qin, Jiayang; Wang, Xiuwen; Zheng, Zhaojuan; Ma, Cuiqing; Tang, Hongzhi; Xu, Ping

2010-10-01

A sodium lactate tolerant mutant strain named Bacillus sp. Na-2 was obtained and applied to sodium hydroxide-based L-lactic acid (LA) production process. The influences of aeration and pH were investigated to further improve the resistance of strain Na-2 against sodium lactate stress and to obtain the most efficient L-LA production process. Although mild aeration was favorable for cell growth and L-LA production, vigorous aeration resulted in a metabolic shift from homolactic to mixed-acid/acetoin fermentation. Therefore, a two-stage aeration control strategy was employed. Optimum pH was found to be 6.0. A total of 106.0 g/l L-LA was produced in 30 h by Bacillus sp. Na-2 using sodium hydroxide as neutralizing agent. Productivity, conversion rate and optical purity were 3.53 g/l/h, 94% and 99.5%, respectively. The remarkable fermentation traits of Bacillus sp. Na-2 and the environment-friendly characteristics of NaOH-based process represent new insight for industrial scale production of L-LA. Copyright 2010 Elsevier Ltd. All rights reserved.

The effect of salt replacers and flavor enhancer on the processing characteristics and consumer acceptance of turkey sausages.

PubMed

Pietrasik, Zeb; Gaudette, Nicole J

2015-07-01

Producing high-quality processed meats that contain reduced amounts of sodium chloride is a major challenge facing industry owing to the importance of sodium chloride toward the functional, microbial stability and sensory properties of these products. In order to create reduced sodium alternatives, a number of commercial salt replacers and flavor enhancers have entered the market; however, their ability to be applied in processed meats requires investigation. In this study, two salt replacers (Ocean's Flavor - OF45, OF60) and one flavor enhancer (Fonterra™ Savoury Powder - SP) were evaluated for their ability to effectively reduce sodium while maintaining the functional and sensory properties of turkey sausages. Functionality via instrumental measures (yield, purge loss, pH, expressible moisture, proximate composition, sodium content, color, texture), safety (microbiological assessment) and consumer acceptability were obtained on all samples. All non-control treatments resulted in products with sodium chloride contents below Canada's Health Check™ Program target for processed meats. There was no detrimental effect on water binding and texture in treatments when NaCl was substituted with OF60 sea salt replacers. Sodium reduction had no negative effect on the shelf life of the turkey sausages with up to 60 days of refrigerated storage. Consumer acceptability for all attributes did not differ significantly, except for aftertaste, which scored lowest for OF45 compared with the control (regular NaCl content). This work demonstrated that salt replacers could potentially substitute for NaCl in smoked turkey sausages; however, further flavor optimization may be required to suppress undesirable levels of bitterness elicited by some of these ingredients. © 2014 Society of Chemical Industry.

Pyroprocessing of Oxidized Sodium-Bonded Fast Reactor Fuel -- an Experimental Study of Treatment Options for Degraded EBR-II Fuel

DOE Office of Scientific and Technical Information (OSTI.GOV)

S. D. Herrmann; L. A. Wurth; N. J. Gese

An experimental study was conducted to assess pyrochemical treatment options for degraded EBR-II fuel. As oxidized material, the degraded fuel would need to be converted back to metal to enable electrorefining within an existing electrometallurgical treatment process. A lithium-based electrolytic reduction process was studied to assess the efficacy of converting oxide materials to metal with a particular focus on the impact of zirconium oxide and sodium oxide on this process. Bench-scale electrolytic reduction experiments were performed in LiCl-Li2O at 650 °C with combinations of manganese oxide (used as a surrogate for uranium oxide), zirconium oxide, and sodium oxide. The experimentalmore » study illustrated how zirconium oxide and sodium oxide present different challenges to a lithium-based electrolytic reduction system for conversion of select metal oxides to metal.« less

Preparation of starch-stabilized silver nanoparticles from amylose-sodium palmitate inclusion complexes

USDA-ARS?s Scientific Manuscript database

Starch-stabilized silver nanoparticles were prepared from amylose-sodium palmitate complexes by first converting sodium palmitate to silver palmitate by reaction with silver nitrate and then reducing the silver ion to metallic silver. This process produced water solutions that could be dried and the...

Structural, textural and sensory impact of sodium reduction on long fermented pizza.

PubMed

Bernklau, Isabelle; Neußer, Christian; Moroni, Alice V; Gysler, Christof; Spagnolello, Alessandro; Chung, Wookyung; Jekle, Mario; Becker, Thomas

2017-11-01

The aim of this study was to elucidate the microstructural, textural, and sensory impact of sodium reduction and its partial replacement by potassium chloride in pizza dough and crusts prepared by a traditional long fermentation process. For the first time, macrostructural changes in texture were elucidated and quantified by a novel protein network analysis. The fermentation process exerted a strengthening effect in the doughs, allowing to reduce sodium up to 25% without any negative impact on texture. Sodium reduction by 15% did not cause any significant textural changes in pizza crusts and partial replacement by KCl resulted in a strengthened dough and firmer pizza crust. The use of toppings masked the effect of lowering the sodium content, allowing to increase the reduction level from 15% to 35%. A reduction of NaCl by 25% with an addition of KCl achieved high acceptance in the sensory evaluation. Copyright © 2017 Elsevier Ltd. All rights reserved.

CALANDRIA TYPE SODIUM GRAPHITE REACTOR

DOEpatents

Peterson, R.M.; Mahlmeister, J.E.; Vaughn, N.E.; Sanders, W.J.; Williams, A.C.

1964-02-11

A sodium graphite power reactor in which the unclad graphite moderator and fuel elements are contained within a core tank is described. The core tank is submersed in sodium within the reactor vessel. Extending longitudinally through the core thnk are process tubes with fuel elements positioned therein. A bellows sealing means allows axial expansion and construction of the tubes. Within the core tank, a leakage plenum is located below the graphite, and above the graphite is a gas space. A vent line regulates the gas pressure in the space, and another line removes sodium from the plenum. The sodium coolant flows from the lower reactor vessel through the annular space between the fuel elements and process tubes and out into the reactor vessel space above the core tank. From there, the heated coolant is drawn off through an outlet line and sent to the heat exchange. (AEC)

Processes for making dense, spherical active materials for lithium-ion cells

DOEpatents

Kang, Sun-Ho [Naperville, IL; Amine, Khalil [Downers Grove, IL

2011-11-22

Processes are provided for making dense, spherical mixed-metal carbonate or phosphate precursors that are particularly well suited for the production of active materials for electrochemical devices such as lithium ion secondary batteries. Exemplified methods include precipitating dense, spherical particles of metal carbonates or metal phosphates from a combined aqueous solution using a precipitating agent such as ammonium hydrogen carbonate, sodium hydrogen carbonate, or a mixture that includes sodium hydrogen carbonate. Other exemplified methods include precipitating dense, spherical particles of metal phosphates using a precipitating agent such as ammonium hydrogen phosphate, ammonium dihydrogen phosphate, sodium phosphate, sodium hydrogen phosphate, sodium dihydrogen phosphate, or a mixture of any two or more thereof. Further provided are compositions of and methods of making dense, spherical metal oxides and metal phosphates using the dense, spherical metal precursors. Still further provided are electrodes and batteries using the same.

Inaugural Maximum Values for Sodium in Processed Food Products in the Americas.

PubMed

Campbell, Norm; Legowski, Barbara; Legetic, Branka; Nilson, Eduardo; L'Abbé, Mary

2015-08-01

Reducing dietary salt/sodium is one of the most cost-effective interventions to improve population health. There are five initiatives in the Americas that independently developed targets for reformulating foods to reduce salt/sodium content. Applying selection criteria, recommended by the Pan American Health Organization (PAHO)/World Health Organization (WHO) Technical Advisory Group on Dietary Salt/Sodium Reduction, a consortium of governments, civil society, and food companies (the Salt Smart Consortium) agreed to an inaugural set of regional maximum targets (upper limits) for salt/sodium levels for 11 food categories, to be achieved by December 2016. Ultimately, to substantively reduce dietary salt across whole populations, targets will be needed for the majority of processed and pre-prepared foods. Cardiovascular and hypertension organizations are encouraged to utilize the regional targets in advocacy and in monitoring and evaluation of progress by the food industry. © 2015 Wiley Periodicals, Inc.

Site Environmental Report for Calendar Year 2001. DOE Operations at The Boeing Company, Rocketdyne Propulsion & Power

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rutherford, Phil; Samuels, Sandy; Leee, Majelle

2002-09-01

This Annual Site Environmental Report (ASER) for 2001 describes the environmental conditions related to work performed for the Department of Energy (DOE) at Area IV of the Boeing Rocketdyne Santa Susana Field Laboratory (SSFL). In the past, these operations included development, fabrication, and disassembly of nuclear reactors, reactor fuel, and other radioactive materials under the former Atomics International (AI) Division. Other activities included the operation of large-scale liquid metal facilities for testing of liquid metal fast breeder components at the Energy Technology Engineering Center (ETEC), a government-owned, company-operated test facility within Area IV. All nuclear work was terminated in 1988,more » and subsequently, all radiological work has been directed toward decontamination and decommissioning (D&D) of the previously used nuclear facilities and associated site areas. Closure of the sodium test facilities began in 1996. Results of the radiological monitoring program for the calendar year of 2001 continue to indicate that there are no significant releases of radioactive material from Area IV of SSFL. All potential exposure pathways are sampled and/or monitored, including air, soil, surface water, groundwater, direct radiation, transfer of property (land, structures, waste), and recycling. All radioactive wastes are processed for disposal at DOE disposal sites and other sites approved by DOE and licensed for radioactive waste. Liquid radioactive wastes are not released into the environment and do not constitute an exposure pathway. No structural debris from buildings, released for unrestricted use, was transferred to municipal landfills or recycled in 2001.« less

Facile reductive amination of aldehydes with electron-deficient anilines by acyloxyborohydrides in TFA: application to a diazaindoline scale-up.

PubMed

Boros, Eric E; Thompson, James B; Katamreddy, Subba R; Carpenter, Andrew J

2009-05-01

A scale-up of diazaindoline 1 was achieved in four stages and 32% overall yield. The key step involved rapid reductive amination of aldehyde 8 with aniline 5 by sodium triacetoxyborohydride (STAB-H) and TFA followed by ring closure of intermediate amine 9 to compound 1 in the same pot. These reaction conditions were also applied to facile reductive aminations with anilines known to have little reactivity under STAB-H/AcOH conditions. Spectral data supported the tris(trifluoroacetoxy)borohydride anion (16) as the active reducing agent.

A Markov State-based Quantitative Kinetic Model of Sodium Release from the Dopamine Transporter

NASA Astrophysics Data System (ADS)

Razavi, Asghar M.; Khelashvili, George; Weinstein, Harel

2017-01-01

The dopamine transporter (DAT) belongs to the neurotransmitter:sodium symporter (NSS) family of membrane proteins that are responsible for reuptake of neurotransmitters from the synaptic cleft to terminate a neuronal signal and enable subsequent neurotransmitter release from the presynaptic neuron. The release of one sodium ion from the crystallographically determined sodium binding site Na2 had been identified as an initial step in the transport cycle which prepares the transporter for substrate translocation by stabilizing an inward-open conformation. We have constructed Markov State Models (MSMs) from extensive molecular dynamics simulations of human DAT (hDAT) to explore the mechanism of this sodium release. Our results quantify the release process triggered by hydration of the Na2 site that occurs concomitantly with a conformational transition from an outward-facing to an inward-facing state of the transporter. The kinetics of the release process are computed from the MSM, and transition path theory is used to identify the most probable sodium release pathways. An intermediate state is discovered on the sodium release pathway, and the results reveal the importance of various modes of interaction of the N-terminus of hDAT in controlling the pathways of release.

Simultaneous inhibition of acrylamide and hydroxymethylfurfural formation by sodium glutamate microcapsules in an asparagine-glucose model system.

PubMed

Wang, Zimeng; Wen, Chao; Shi, Xingbo; Lu, Dai; Deng, Jiehong; Deng, Fangming

2017-02-01

Inhibiting the formation of acrylamide (AA) and hydroxymethylfurfural (HMF) during food heating processes has attracted considerable investigative efforts due to potential health concerns associated with these compounds. The main purpose of this work is to demonstrate a strategy to simultaneously inhibit the formation of AA and HMF with sodium glutamate microcapsules selected to confirm the efficacy of this strategy. An asparagine-glucose aqueous model system was prepared containing free sodium glutamate and sodium glutamate microcapsules. Compared to adding free sodium glutamate, the maximum inhibition efficiency for AA and HMF was found to increase by addition of sodium glutamate microcapsules to 19.07 and 84.32%, respectively. Moreover, the kinetics of AA and HMF formation were studied in this model system. The AA inhibition efficiency significantly increased from 6.75 to 60.35% and the HMF inhibition efficiency significantly increased from 5.98 to 79.72% with increasing the reaction time from 25 to 40 min, indicating that the sodium glutamate microcapsules strategy proves to be far superior at prolonged heating times. These findings suggested that this inhibition strategy may provide promising characteristics for a variety of applications in food processing.

Ratio of Sodium to Potassium in the Mercurian Exosphere

NASA Technical Reports Server (NTRS)

Potter, A. E.; Anderson, C. M.; Killen, R. M.; Morgan, T. H.

2001-01-01

Sodium (Na) and Potassium (K) atoms can be seen in the exosphere of Mercury and the Moon because they are extremely efficient at scattering sunlight. These species must be derived from surface materials, so that we might expect the ratio of sodium to potassium to reflect the ratio of these elements in the surface crust. This expectation is approximately born out for the Moon, where the ratio of sodium to potassium in the lunar exosphere averages to be about 6, not too far from the ratio in lunar rocks of 2 to 7. However, the ratio in the Mercury exosphere was found to be in the range 80 to 190, and at least once, as high as 400. The sodium and potassium atoms seen in the Mercury exosphere represent a balance between production from the surface and loss to space. Only if the production efficiencies and loss rates for Na and K were equal, would the ratio of Na to K in the exosphere reflect the ratio in the surface rocks. Since a value of 100 or more for the ratio of sodium to potassium in the surface rocks seems very unlikely, the high values of the observed ratios suggests that either production efficiencies or loss processes for the two elements are not equivalent. It does not seem likely that source processes should be different on the Moon and Mercury by an order of magnitude. This suggests that loss processes rather than source processes are the cause of the difference between the two. The major loss processes for sodium and potassium on Mercury are radiation pressure and trapping of photoions by the solar wind. Radiation pressure can reach 50-70% of surface gravity, and can sweep sodium and potassium atoms off the planet, provided they are sufficiently hot. Photoionization followed by trapping of the ions in the solar wind is the other major loss process. Photoions are accelerated to keV energies in the magnetosphere, and may either intercept the magnetopause, and be lost from the planet, or impact the planetary surface. Ions that impact the surface are neutralized, and are then available for resupply to the exosphere. The loss efficiency depends on characteristics of the magnetosphere that determine the fraction of the ions that are recycled by neutralization on the surface. Over the preceding decade, we have collected sodium and potassium data for Mercury at irregular intervals. We analyzed these data to extract values for the Na/K ratio at a variety of conditions on Mercury. Additional information is contained in the original extended abstract.

Characterization of Sodium Mobility and Binding by 23 Na NMR Spectroscopy in a Model Lipoproteic Emulsion Gel for Sodium Reduction.

PubMed

Okada, Kyle S; Lee, Youngsoo

2017-07-01

The effects of formulation and processing parameters on sodium availability in a model lipid/protein-based emulsion gel were studied for purposes of sodium reduction. Heat-set model gels were prepared with varying levels of protein, lipid, and NaCl contents and high pressure homogenization treatments. Single quantum and double quantum-filtered 23 Na NMR spectroscopy experiments were used to characterize sodium mobility, structural order around "bound" (restricted mobility) sodium, and sodium binding, which have been correlated to saltiness perception in food systems previously. Total sodium mobility was lower in gels with higher protein or fat content, and was not affected by changes in homogenization pressure. The gels with increased protein, fat, or homogenization pressure had increased structure surrounding "bound" sodium and more relative "bound" sodium due to increased interfacial protein interactions. The data obtained in this study provide information on factors affecting sodium availability, which can be applied towards sodium reduction in lipid/protein-based foods. © 2017 Institute of Food Technologists®.

SIMPLIFIED SODIUM GRAPHITE REACTOR SYSTEM

DOEpatents

Dickinson, R.W.

1963-03-01

This patent relates to a nuclear power reactor comprising a reactor vessel, shielding means positioned at the top of said vessel, means sealing said reactor vessel to said shielding means, said vessel containing a quantity of sodium, a core tank, unclad graphite moderator disposed in said tank, means including a plurality of process tubes traversing said tank for isolating said graphite from said sodium, fuel elements positioned in said process tubes, said core tank being supported in spaced relation to the walls and bottom of said reactor vessel and below the level of said sodium, neutron shielding means positioned adjacent said core tank between said core tank and the walls of said vessel, said neutron shielding means defining an annuiar volume adjacent the inside wall of said reactor vessel, inlet plenum means below said core tank for providing a passage between said annular volume and said process tubes, heat exchanger means removably supported from the first-named shielding means and positioned in said annular volume, and means for circulating said sodium over said neutron shielding means down through said heat exchanger, across said inlet plenum and upward through said process tubes, said last-named means including electromagnetic pumps located outside said vessel and supported on said vessel wall between said heat exchanger means and said inlet plenum means. (AEC)

A confined "microreactor" synthesis strategy to three dimensional nitrogen-doped graphene for high-performance sodium ion battery anodes

NASA Astrophysics Data System (ADS)

Li, Jiajie; Zhang, Yumin; Gao, Tangling; Han, Jiecai; Wang, Xianjie; Hultman, Benjamin; Xu, Ping; Zhang, Zhihua; Wu, Gang; Song, Bo

2018-02-01

In virtue of abundant sodium resources, sodium ion batteries (SIBs) have been regarded as one of the most promising alternatives for large-scale energy storage applications. However, the absence of a suitable anode material makes it difficult to realize these applications. Here, we demonstrate an effective synthesis strategy of using a "microreactor" consisting of melamine fiber (inside) and graphene oxide (GO, outside) to fabricate three dimensional (3D) nitrogen doped (N-doped) graphene as high-performance anode materials for sodium ion batteries. Through a controlled pyrolysis, the inside melamine fiber and the outside GO layer has been converted into N-doped graphene and reduced graphene oxide (r-GO) respectively, and thus the "microreactor" is transformed into interconnected 3D N-doped graphene structures. Such highly desired 3D graphene structures show reversible sodium storage capacities up to ∼305 mA h g-1 after 500 cycles at a current density of 0.2 A g-1 and promising long cycling stability with a stable capacity of ∼198 mA h g-1 at 5 A g-1 after 5000 cycles. The high capacity and superior durability in combination with the facile synthesis procedure of the 3D graphene structure make it a promising anode material for SIBs and other energy storage applications.

Sodium content in processed foods in Argentina: compliance with the national law.

PubMed

Allemandi, Lorena; Tiscornia, María Victoria; Ponce, Miguel; Castronuovo, Luciana; Dunford, Elizabeth; Schoj, Verónica

2015-06-01

Despite the body of evidence that documents the unfavorable effects of excessive sodium consumption on blood pressure and cardiovascular health, public health efforts to decrease sodium consumption have been limited to a few countries. Argentina is the first country in Latin America to regulate sodium content of processed foods by means of a national law. The objective of this cross-sectional quantitative study is to provide a baseline comparison against the reduction targets set by the national law before its entry into force. Data were collected in February 2014 in a leading supermarket chain located in Buenos Aires. Nutrient data from package labels were analysed for 1,320 products within 14 food groups during the study period. To compare sodium concentration levels with the established maximum levels we matched the collected food groups with the food groups included in the law resulting in a total of 292 products. Data analysis was conducted using SPSS version 20 software. Food groups with the highest median sodium content were sauces and spreads (866.7 mg/100 g), meat and meat products (750 mg/100 g) and snack foods (644 mg/100 g). Categories with the highest sodium content were appetizers (1,415 mg/100 g), sausages (1,050 mg/100 g) and ready-made meals (940.7 mg/100 g). We also found large variability within products from the same food categories. Products included in the national law correspond to 22.1% (n=292) of the surveyed foods. From the 18 food groups, 15 showed median sodium values below the established targets. Products exceeding the established maximum levels correspond to 15.1% (n=44) of the products included in the analysis. This study is the first analysis of food labels to determine sodium concentrations of processed foods in Argentina and to provide a baseline against the national law standards. Upon the completion of this analysis, maximum levels have been achieved by most of the food groups included in the law. Thus, the introduction of further reductions for the existing maximum levels and the establishment of sodium targets for all relevant product categories not included in the law should be considered as the next steps in the process.

PROCESS FOR RECOVERY OF URANIUM AND VANADIUM FROM CARBONATE SOLUTIONS BY REDUCTION-PRECIPITATION

DOEpatents

Ellis, D.A.; Lindblom, R.O.

1957-09-24

A process employing carbonate leaching of ores and an advantageous methcd of recovering the uranium and vanadium from the leach solution is described. The uranium and vanadium can be precipitated from carbonate leach solutions by reaction with sodium amalgam leaving the leach solution in such a condition that it is economical to replenish for recycling. Such a carbonate leach solution is treated with a dilute sodium amalgam having a sodium concentration within a range of about 0.01 to 0.5% of sodium. Efficiency of the treatment is dependent on at least three additional factors, intimacy of contact of the amalgam with the leach solution, rate of addition of the amalgam and exclusion of oxygen (air).

40 CFR 721.10237 - Formaldehyde, polymers with acetone-phenol reaction products and phenol, sodium salts.

Code of Federal Regulations, 2014 CFR

2014-07-01

... ratios are as specified in the TSCA section 5(e) consent order. (B) Upon start-up of manufacture of the PMN at any new facility, conduct the American Society for Testing and Materials International (ASTM..., demonstrating that formaldehyde emissions are less than or equal to 0.04 ppm. (C) Development and implementation...

40 CFR 721.10237 - Formaldehyde, polymers with acetone-phenol reaction products and phenol, sodium salts.

Code of Federal Regulations, 2013 CFR

2013-07-01

... ratios are as specified in the TSCA section 5(e) consent order. (B) Upon start-up of manufacture of the PMN at any new facility, conduct the American Society for Testing and Materials International (ASTM..., demonstrating that formaldehyde emissions are less than or equal to 0.04 ppm. (C) Development and implementation...

GATEWAY Demonstrations: Philadelphia International Airport Apron Lighting: LED System Performance in a Trial Installation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Davis, Robert G.; Wilkerson, Andrea M.

This report documents a trial installation of LED apron lighting that replaced the existing high-pressure sodium luminaires at Philadelphia International Airport. Such high-mast applications remain challenging for LED technology, and the lessons learned from this project may help facility managers and LED product manufacturers better meet those challenges.

Facile Synthesis of Monodispersed Polysulfide Spheres for Building Structural Colors with High Color Visibility and Broad Viewing Angle.

PubMed

Li, Feihu; Tang, Bingtao; Wu, Suli; Zhang, Shufen

2017-01-01

The synthesis and assembly of monodispersed colloidal spheres are currently the subject of extensive investigation to fabricate artificial structural color materials. However, artificial structural colors from general colloidal crystals still suffer from the low color visibility and strong viewing angle dependence which seriously hinder their practical application in paints, colorimetric sensors, and color displays. Herein, monodispersed polysulfide (PSF) spheres with intrinsic high refractive index (as high as 1.858) and light-absorbing characteristics are designed, synthesized through a facile polycondensation and crosslinking process between sodium disulfide and 1,2,3-trichloropropane. Owing to their high monodispersity, sufficient surface charge, and good dispersion stability, the PSF spheres can be assembled into large-scale and high-quality 3D photonic crystals. More importantly, high structural color visibility and broad viewing angle are easily achieved because the unique features of PSF can remarkably enhance the relative reflectivity and eliminate the disturbance of scattering and background light. The results of this study provide a simple and efficient strategy to create structural colors with high color visibility, which is very important for their practical application. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Process and apparatus for obtaining silicon from fluosilicic acid

DOEpatents

Sanjurjo, Angel

1988-06-28

Process and apparatus for producing low cost, high purity solar grade silicon ingots in single crystal or quasi single crystal ingot form in a substantially continuous operation in a two stage reactor starting with sodium fluosilicate and a metal more electropositive than silicon (preferably sodium) in separate compartments having easy vapor transport therebetween and thermally decomposing the sodium fluosilicate to cause formation of substantially pure silicon and a metal fluoride which may be continuously separated in the melt and silicon may be directly and continuously cast from the melt.

Hierarchical Na-doped cubic ZrO{sub 2} synthesis by a simple hydrothermal route and its application in biodiesel production

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lara-García, Hugo A.; Romero-Ibarra, Issis C.; Pfeiffer, Heriberto, E-mail: pfeiffer@iim.unam.mx

Hierarchical growth of cubic ZrO{sub 2} phase was successfully synthesized via a simple hydrothermal process in the presence of different surfactants (cationic, non-ionic and anionic) and sodium hydroxide. The structural and microstructural characterizations of different ZrO{sub 2} powders were performed using various techniques, such as X-ray diffraction, transmission electron microscopy, N{sub 2} adsorption–desorption, scanning electron microscopy and infrared. Results indicated that sodium addition stabilized the cubic ZrO{sub 2} phase by a Na-doping process, independently of the surfactant used. In contrast, microstructural characteristics varied as a function of the surfactant and sodium presence. In addition, water vapor (H{sub 2}O) and carbonmore » dioxide (CO{sub 2}) sorption properties were evaluated on ZrO{sub 2} samples. Results evidenced that sample surface reactivity changed as a function of the sodium content. Finally, this surface reactivity was evaluated on the biodiesel transesterification reaction using the different synthesized samples, obtaining yields of 93%. - Graphical abstract: Hierarchical growth of cubic Na-ZrO{sub 2} phase was synthesized by hydrothermal processes in the presence of surfactants and sodium. Sodium addition stabilized the cubic phase by a Na-doping process, while the microstructural characteristics varied with surfactants. Finally, this surface reactivity was evaluated on the biodiesel transesterification reaction. - Highlights: • Cubic-ZrO{sub 2} phase was synthesized via a simple hydrothermal process. • ZrO{sub 2} structure and microstructures changed as a function of the surfactant. • Cubic-ZrO{sub 2} phase was evaluated on the biodiesel transesterification reaction.« less

Electroless plating of Ni-B film as a binder-free highly efficient electrocatalyst for hydrazine oxidation

NASA Astrophysics Data System (ADS)

Wen, Xiao-Ping; Dai, Hong-Bin; Wu, Lin-Song; Wang, Ping

2017-07-01

Hydrazine is a promising energy carrier for fuel cells owing to its combined advantages of high theoretical cell voltage, high-power density, and no greenhouse gas emission. By using an electroless plating process, we have prepared a robust Ni-B film grown on Ni foam that is highly effective for hydrazine electrooxidation in alkaline media. The effects of reaction temperature, concentrations of hydrous hydrazine and sodium hydroxide in the fuel solution on performance of hydrazine electrooxidation reaction are investigated. The mechanistic reason for the property advantage of as-prepared Ni-B/Ni foam catalyst over the relevant catalysts is discussed based on careful kinetics studies and characterization. The facile synthesis of Ni-based catalyst with high activity and good stability is of clear significance for the development of hydrous hydrazine as a viable energy carrier.

Sodium metasilicate based fiber opening for greener leather processing.

PubMed

Saravanabhavan, Subramani; Thanikaivelan, Palanisamy; Rao, Jonnalagadda Raghava; Nair, Balachandran Unni; Ramasamit, Thirumalachari

2008-03-01

Growing environmental regulations propound the need for a transformation in the current practice of leather making. The conventional dehairing and fiber opening process results in high negative impact on the environment because of its uncleanliness. This process accounts for most of the biochemical oxygen demand and chemical oxygen demand in tannery wastewater and generation of H2S gas. Hence, this study explores the use of a biological material and a nontoxic chemical for performing the above process more cleanly. In this study, the dehairing and fiber opening processes has been designed using enzyme and sodium metasilicate. The amount of sodium metasilicate required for fiber opening is standardized through the removal of proteoglycan, increase in weight, and bulk properties of leathers. It has been found that the extent of opening up of fiber bundles is comparable to that of conventionally processed leathers using a 2% sodium metasilicate solution. This has been substantiated through scanning electron microscopic analysis and softness measurements. The presence of silica in the crust leather enhances the bulk properties of the leather. This has been confirmed from the energy dispersive X-ray analysis. Performance of the leathers is shown to be on par with conventionally processed leathers through physical and hand evaluation. The process also exhibits significant reduction in chemical oxygen demand and total solid loads by 55 and 24%, respectively. Further, this newly developed process seems to be economically beneficial.

Alternative MyPlate Menus: Effects of Ultra-Processed Foods on Saturated Fat, Sugar, and Sodium Content.

PubMed

Tseng, Marilyn; Neill, Dawn B; Teaford, Stephanie F; Nazmi, Aydin

2018-03-01

Compare saturated fat, sugar, and sodium in the US Department of Agriculture sample menu with a version in which menu items were replaced with comparable ultra-processed foods. The authors modified 7 days of a US Department of Agriculture sample menu providing approximately 2,000 kcal/d by replacing foods with comparable ultra-processed alternatives and then visited 2 chain supermarkets in San Luis Obispo, CA (August, 2016) to locate shopping list items for the 2 menu versions. Product-specific bar codes were entered into an application for recording dietary intake and analyzing nutrient content. Paired t tests (with Bonferroni correction, α = .003) were performed to compare the menus' percent energy from saturated fat and sugar, and energy and sodium content. Mean energy was lower (1,618 vs 1,892 kcal/d; P = .002) whereas percent energy from sugar (24.9% vs 21.4%; P ≤ .001) and sodium content (2,784 vs 2,101 mg/d; P = .001) were higher in the ultra-processed vs original menu. In secondary analyses, mean cost of the ultra-processed version exceeded that of the original menu by $36.87. In a sample menu developed to meet US Dietary Guidelines, substituting items with ultra-processed foods provided fewer calories but more sugar and sodium. Distinguishing ultra-processed from less processed foods may help consumers make healthier choices when using MyPlate tools, particularly in a food environment that presents a wide range of alternatives. Copyright © 2017 Society for Nutrition Education and Behavior. Published by Elsevier Inc. All rights reserved.

Method of removing bulk sodium from metallic surfaces

DOEpatents

Maffei, H.P.; Borisch, R.R.

1975-11-11

A process of removing sodium from an article, particularly one made of stainless steel, by treating it with a mixture of water vapor and a gas which is inert to sodium is described. By selecting combinations of temperature and water vapor-to-gas ratio, the reaction temperature is controlled to prevent damage to the articles.

40 CFR 415.162 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... SOURCE CATEGORY Sodium Chloride Production Subcategory § 415.162 Effluent limitations guidelines... added to the bitterns during the production of sodium chloride. (b) Except as provided in 40 CFR 125.30...—Sodium Chloride Brine Mining Process Pollutant or pollutant property BPT limitations Maximum for any 1...

Photon-stimulated desorption as a substantial source of sodium in the lunar atmosphere.

PubMed

Yakshinskiy, B V; Madey, T E

1999-08-12

Mercury and the Moon both have tenuous atmospheres that contain atomic sodium and potassium. These chemicals must be continuously resupplied, as neither body can retain the atoms for more than a few hours. The mechanisms proposed to explain the resupply include sputtering of the surface by the solar wind, micrometeorite impacts, thermal desorption and photon-stimulated desorption. But there are few data and no general agreement about which processes dominate. Here we report laboratory studies of photon-stimulated desorption of sodium from surfaces that simulate lunar silicates. We find that bombardment of such surfaces at temperatures of approximately 250 K by ultraviolet photons (wavelength lambda < 300 nm) causes very efficient desorption of sodium atoms, induced by electronic excitations rather than by thermal processes or momentum transfer. The flux at the lunar surface of ultraviolet photons from the Sun is sufficient to ensure that photon-stimulated desorption of sodium contributes substantially to the Moon's atmosphere. On Mercury, solar heating of the surface implies that thermal desorption will also be an important source of atmospheric sodium.

Facile preparation and enhanced capacitance of the polyaniline/sodium alginate nanofiber network for supercapacitors.

PubMed

Li, Yingzhi; Zhao, Xin; Xu, Qian; Zhang, Qinghua; Chen, Dajun

2011-05-17

A porous and mat-like polyaniline/sodium alginate (PANI/SA) composite with excellent electrochemical properties was polymerized in an aqueous solution with sodium sulfate as a template. Ultraviolet-visible spectra, X-ray diffraction pattern, and Fourier transform infrared spectra were employed to characterize the PANI/SA composite, indicating that the PANI/SA composite was successfully prepared. The PANI/SA nanofibers with uniform diameters from 50 to 100 nm can be observed on scanning electron microscopy. Cyclic voltammetry and galvanostatic charge/discharge tests were carried out to investigate the electrochemical properties. The PANI/SA nanostructure electrode exhibits an excellent specific capacitance as high as 2093 F g(-1), long cycle life, and fast reflect of oxidation/reduction on high current changes. The remarkable electrochemical characteristic is attributed to the nanostructured electrode materials, which generates a high electrode/electrolyte contact area and short path lengths for electronic transport and electrolyte ion. The approach is simple and can be easily extended to fabricate nanostructural composites for supercapacitor electrode materials.

A liquid-metal filling system for pumped primary loop space reactors

NASA Astrophysics Data System (ADS)

Crandall, D. L.; Reed, W. C.

Some concepts for the SP-100 space nuclear power reactor use liquid metal as the primary coolant in a pumped loop. Prior to filling ground engineering test articles or reactor systems, the liquid metal must be purified and circulated through the reactor primary system to remove contaminants. If not removed, these contaminants enhance corrosion and reduce reliability. A facility was designed and built to support Department of Energy Liquid Metal Fast Breeder Reactor tests conducted at the Idaho National Engineering Laboratory. This test program used liquid sodium to cool nuclear fuel in in-pile experiments; thus, a system was needed to store and purify sodium inventories and fill the experiment assemblies. This same system, with modifications and potential changeover to lithium or sodium-potassium (NaK), can be used in the Space Nuclear Power Reactor Program. This paper addresses the requirements, description, modifications, operation, and appropriateness of using this liquid-metal system to support the SP-100 space reactor program.

Electrochemical route to the synthesis of ZnO microstructures: its nestlike structure and holding of Ag particles

NASA Astrophysics Data System (ADS)

Ding, Ling; Zhang, Ruixue; Fan, Louzhen

2013-02-01

A simple and facile electrochemical route was developed for the shape-selective synthesis of large-scaled series of ZnO microstructures, including petal, flower, sphere, nest and clew aggregates of ZnO laminas at room temperature. This route is based on sodium citrate-directed crystallization. In the system, sodium citrate can greatly promote ZnO to nucleate and directly grow by selectively capping the specific ZnO facets because of its excellent adsorption ability. The morphology of ZnO is tuned by readily adjusting the concentration of sodium citrate and the electrodeposition time. Among the series structures, the remarkable ZnO nestlike structure can be used as a container to hold not only the interlaced ZnO laminas but also Ag nanoparticles in the center. The special heterostructures of nestlike ZnO holding Ag nanoparticles were found to display the superior properties on the surface-enhanced Raman scattering. This work has signified an important methodology to produce a wide assortment of desired microstructures of ZnO.

Design and implementation of a preprocessing system for a sodium lidar

NASA Technical Reports Server (NTRS)

Voelz, D. G.; Sechrist, C. F., Jr.

1983-01-01

A preprocessing system, designed and constructed for use with the University of Illinois sodium lidar system, was developed to increase the altitude resolution and range of the lidar system and also to decrease the processing burden of the main lidar computer. The preprocessing system hardware and the software required to implement the system are described. Some preliminary results of an airborne sodium lidar experiment conducted with the preprocessing system installed in the sodium lidar are presented.

Programmed emulsions for sodium reduction in emulsion based foods.

PubMed

Chiu, Natalie; Hewson, Louise; Fisk, Ian; Wolf, Bettina

2015-05-01

In this research a microstructure approach to reduce sodium levels in emulsion based foods is presented. If successful, this strategy will enable reduction of sodium without affecting consumer satisfaction with regard to salty taste. The microstructure approach comprised of entrapment of sodium in the internal aqueous phase of water-in-oil-in-water emulsions. These were designed to destabilise during oral processing when in contact with the salivary enzyme amylase in combination with the mechanical manipulation of the emulsion between the tongue and palate. Oral destabilisation was achieved through breakdown of the emulsion that was stabilised with a commercially modified octenyl succinic anhydride (OSA)-starch. Microstructure breakdown and salt release was evaluated utilising in vitro, in vivo and sensory methods. For control emulsions, stabilised with orally inert proteins, no loss of structure and no release of sodium from the internal aqueous phase was found. The OSA-starch microstructure breakdown took the initial form of oil droplet coalescence. It is hypothesised that during this coalescence process sodium from the internalised aqueous phase is partially released and is therefore available for perception. Indeed, programmed emulsions showed an enhancement in saltiness perception; a 23.7% reduction in sodium could be achieved without compromise in salty taste (p < 0.05; 120 consumers). This study shows a promising new approach for sodium reduction in liquid and semi-liquid emulsion based foods.

Dietary Impact of Adding Potassium Chloride to Foods as a Sodium Reduction Technique.

PubMed

van Buren, Leo; Dötsch-Klerk, Mariska; Seewi, Gila; Newson, Rachel S

2016-04-21

Potassium chloride is a leading reformulation technology for reducing sodium in food products. As, globally, sodium intake exceeds guidelines, this technology is beneficial; however, its potential impact on potassium intake is unknown. Therefore, a modeling study was conducted using Dutch National Food Survey data to examine the dietary impact of reformulation (n = 2106). Product-specific sodium criteria, to enable a maximum daily sodium chloride intake of 5 grams/day, were applied to all foods consumed in the survey. The impact of replacing 20%, 50% and 100% of sodium chloride from each product with potassium chloride was modeled. At baseline median, potassium intake was 3334 mg/day. An increase in the median intake of potassium of 453 mg/day was seen when a 20% replacement was applied, 674 mg/day with a 50% replacement scenario and 733 mg/day with a 100% replacement scenario. Reformulation had the largest impact on: bread, processed fruit and vegetables, snacks and processed meat. Replacement of sodium chloride by potassium chloride, particularly in key contributing product groups, would result in better compliance to potassium intake guidelines (3510 mg/day). Moreover, it could be considered safe for the general adult population, as intake remains compliant with EFSA guidelines. Based on current modeling potassium chloride presents as a valuable, safe replacer for sodium chloride in food products.

DWPF RECYCLE EVAPORATOR FLOWSHEET EVALUATION (U)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stone, M

2005-04-30

The Defense Waste Processing Facility (DWPF) converts the high level waste slurries stored at the Savannah River Site into borosilicate glass for long-term storage. The vitrification process results in the generation of approximately five gallons of dilute recycle streams for each gallon of waste slurry vitrified. This dilute recycle stream is currently transferred to the H-area Tank Farm and amounts to approximately 1,400,000 gallons of effluent per year. Process changes to incorporate salt waste could increase the amount of effluent to approximately 2,900,000 gallons per year. The recycle consists of two major streams and four smaller streams. The first majormore » recycle stream is condensate from the Chemical Process Cell (CPC), and is collected in the Slurry Mix Evaporator Condensate Tank (SMECT). The second major recycle stream is the melter offgas which is collected in the Off Gas Condensate Tank (OGCT). The four smaller streams are the sample flushes, sump flushes, decon solution, and High Efficiency Mist Eliminator (HEME) dissolution solution. These streams are collected in the Decontamination Waste Treatment Tank (DWTT) or the Recycle Collection Tank (RCT). All recycle streams are currently combined in the RCT and treated with sodium nitrite and sodium hydroxide prior to transfer to the tank farm. Tank Farm space limitations and previous outages in the 2H Evaporator system due to deposition of sodium alumino-silicates have led to evaluation of alternative methods of dealing with the DWPF recycle. One option identified for processing the recycle was a dedicated evaporator to concentrate the recycle stream to allow the solids to be recycled to the DWPF Sludge Receipt and Adjustment Tank (SRAT) and the condensate from this evaporation process to be sent and treated in the Effluent Treatment Plant (ETP). In order to meet process objectives, the recycle stream must be concentrated to 1/30th of the feed volume during the evaporation process. The concentrated stream must be pumpable to the DWPF SRAT vessel and should not precipitate solids to avoid fouling the evaporator vessel and heat transfer coils. The evaporation process must not generate excessive foam and must have a high Decontamination Factor (DF) for many species in the evaporator feed to allow the condensate to be transferred to the ETP. An initial scoping study was completed in 2001 to evaluate the feasibility of the evaporator which concluded that the concentration objectives could be met. This initial study was based on initial estimates of recycle concentration and was based solely on OLI modeling of the evaporation process. The Savannah River National Laboratory (SRNL) has completed additional studies using simulated recycle streams and OLI{reg_sign} simulations. Based on this work, the proposed flowsheet for the recycle evaporator was evaluated for feasibility, evaporator design considerations, and impact on the DWPF process. This work was in accordance with guidance from DWPF-E and was performed in accordance with the Technical Task and Quality Assurance Plan.« less

Thermochemical cyclic system for decomposing H/sub 2/O and/or CO/sub 2/ by means of cerium-titanium-sodium-oxygen compounds

DOEpatents

Bamberger, C.E.

1980-04-24

A thermochemical closed cyclic process for the decomposition of water and/or carbon dioxide to hydrogen and/or carbon monoxide begins with the reaction of ceric oxide (CeO/sub 2/), titanium dioxide (TiO/sub 2/) and sodium titanate (Na/sub 2/TiO/sub 3/) to form sodium cerous titanate (NaCeTi/sub 2/O/sub 6/) and oxygen. Sodium cerous titanate (NaCeTi/sub 2/O/sub 6/) reacted with sodium carbonate (Na/sub 2/CO/sub 3/) in the presence of steam, produces hydrogen. The same reaction, in the absence of steam, produces carbon monoxide. The products, ceric oxide and sodium titanate, obtained in either case, are treated with carbon dioxide and water to produce ceric oxide, titanium dioxide, sodium titanate, and sodium bicarbonate. After dissolving sodium bicarbonate from the mixture in water, the remaining insoluble compounds are used as starting materials for a subsequent cycle. The sodium bicarbonate can be converted to sodium carbonate by heating and returned to the cycle.

Thermochemical cyclic system for decomposing H.sub.2 O and/or CO.sub.2 by means of cerium-titanium-sodium-oxygen compounds

DOEpatents

Bamberger, Carlos E.

1982-01-01

A thermochemical closed cyclic process for the decomposition of water and/or carbon dioxide to hydrogen and/or carbon monoxide begins with the reaction of ceric oxide (CeO.sub.2), titanium dioxide (TiO.sub.2) and sodium titanate (Na.sub.2 TiO.sub.3) to form sodium cerous titanate (NaCeTi.sub.2 O.sub.6) and oxygen. Sodium cerous titanate (NaCeTi.sub.2 O.sub.6) reacted with sodium carbonate (Na.sub.2 CO.sub.3) in the presence of steam, produces hydrogen. The same reaction, in the absence of steam, produces carbon monoxide. The products, ceric oxide and sodium titanate, obtained in either case, are treated with carbon dioxide and water to produce ceric oxide, titanium dioxide, sodium titanate, and sodium bicarbonate. After dissolving sodium bicarbonate from the mixture in water, the remaining insoluble compounds are used as starting materials for a subsequent cycle. The sodium bicarbonate can be converted to sodium carbonate by heating and returned to the cycle.

Process for making transition metal nitride whiskers

DOEpatents

Bamberger, Carlos E.

1989-01-01

A process for making metal nitrides, particularly titanium nitride whiskers, using a cyanide salt as a reducing agent for a metal compound in the presence of an alkali metal oxide. Sodium cyanide, various titanates and titanium oxide mixed with sodium oxide react to provide titanium nitride whiskers that can be used as reinforcement to ceramic composites.

Sodium content of popular commercially processed and restaurant foods in the United States

USDA-ARS?s Scientific Manuscript database

Nutrient Data Laboratory (NDL) of the U.S. Department of Agriculture (USDA) in close collaboration with U.S. Center for Disease Control and Prevention is monitoring the sodium content of commercially processed and restaurant foods in the United States. The main purpose of this manuscript is to prov...

Calcium hydroxide as a processing base in alkali-aided pH-shift protein recovery process.

PubMed

Paker, Ilgin; Jaczynski, Jacek; Matak, Kristen E

2017-02-01

Protein may be recovered by using pH shifts to solubilize and precipitate protein. Typically, sodium hydroxide is used as the processing base; however, this has been shown to significantly increase sodium in the final recovered protein. Protein was extracted from black bullhead catfish (Ameiurus melas) using a pH-shift method. Protein was solubilized using either sodium hydroxide (NaOH) or calcium hydroxide (Ca(OH) 2 ) and precipitated at pH 5.5 using hydrochloric acid (HCl). Protein solubility was greater when Ca(OH) 2 was used compared to NaOH during this process. Using Ca(OH) 2 as the processing base yielded the greatest lipid recovery (P < 0.05) at 77 g 100 g -1 , whereas the greatest (P < 0.05) protein recovery yield was recorded as 53 g 100 g -1 protein using NaOH. Protein solubilized with Ca(OH) 2 had more (P < 0.05) calcium in the protein fraction, whereas using NaOH increased (P < 0.05) sodium content. Results of our study showed that protein solubility was increased and the recovered protein had significantly more calcium when Ca(OH) 2 was used as the processing base. Results showed both NaOH and Ca(OH) 2 to be an effective processing base for pH-shift protein recovery processes. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

A method for recovery of iron, titanium, and vanadium from vanadium-bearing titanomagnetite

NASA Astrophysics Data System (ADS)

Zhang, Yi-min; Wang, Li-na; Chen, De-sheng; Wang, Wei-jing; Liu, Ya-hui; Zhao, Hong-xin; Qi, Tao

2018-02-01

An innovative method for recovering valuable elements from vanadium-bearing titanomagnetite is proposed. This method involves two procedures: low-temperature roasting of vanadium-bearing titanomagnetite and water leaching of roasting slag. During the roasting process, the reduction of iron oxides to metallic iron, the sodium oxidation of vanadium oxides to water-soluble sodium vanadate, and the smelting separation of metallic iron and slag were accomplished simultaneously. Optimal roasting conditions for iron/slag separation were achieved with a mixture thickness of 42.5 mm, a roasting temperature of 1200°C, a residence time of 2 h, a molar ratio of C/O of 1.7, and a sodium carbonate addition of 70wt%, as well as with the use of anthracite as a reductant. Under the optimal conditions, 93.67% iron from the raw ore was recovered in the form of iron nugget with 95.44% iron grade. After a water leaching process, 85.61% of the vanadium from the roasting slag was leached, confirming the sodium oxidation of most of the vanadium oxides to water-soluble sodium vanadate during the roasting process. The total recoveries of iron, vanadium, and titanium were 93.67%, 72.68%, and 99.72%, respectively.

Salt craving: the psychobiology of pathogenic sodium intake.

PubMed

Morris, Michael J; Na, Elisa S; Johnson, Alan Kim

2008-08-06

Ionic sodium, obtained from dietary sources usually in the form of sodium chloride (NaCl, common table salt) is essential to physiological function, and in humans salt is generally regarded as highly palatable. This marriage of pleasant taste and physiological utility might appear fortunate--an appealing taste helps to ensure that such a vital substance is ingested. However, the powerful mechanisms governing sodium retention and sodium balance are unfortunately best adapted for an environment in which few humans still exist. Our physiological and behavioral means for maintaining body sodium and fluid homeostasis evolved in hot climates where sources of dietary sodium were scarce. For many reasons, contemporary diets are high in salt and daily sodium intakes are excessive. High sodium consumption can have pathological consequences. Although there are a number of obstacles to limiting salt ingestion, high sodium intake, like smoking, is a modifiable behavioral risk factor for many cardiovascular diseases. This review discusses the psychobiological mechanisms that promote and maintain excessive dietary sodium intake. Of particular importance are experience-dependent processes including the sensitization of the neural systems underlying sodium appetite and the effects of sodium balance on hedonic state and mood. Accumulating evidence suggests that plasticity within the central nervous system as a result of experience with high salt intake, sodium depletion, or a chronic unresolved sodium appetite fosters enduring changes in sodium related appetitive and consummatory behaviors.

Salt craving: The psychobiology of pathogenic sodium intake

PubMed Central

Morris, Michael J.; Na, Elisa S.; Johnson, Alan Kim

2008-01-01

Ionic sodium, obtained from dietary sources usually in the form of sodium chloride (NaCl, common table salt) is essential to physiological function, and in humans salt is generally regarded as highly palatable. This marriage of pleasant taste and physiological utility might appear fortunate – an appealing taste helps to ensure that such a vital substance is ingested. However, the powerful mechanisms governing sodium retention and sodium balance are unfortunately best adapted for an environment in which few humans still exist. Our physiological and behavioral means for maintaining body sodium and fluid homeostasis evolved in hot climates where sources of dietary sodium were scarce. For many reasons, contemporary diets are high in salt and daily sodium intakes are excessive. High sodium consumption can have pathological consequences. Although there are a number of obstacles to limiting salt ingestion, high sodium intake, like smoking, is a modifiable behavioral risk factor for many cardiovascular diseases. This review discusses the psychobiological mechanisms that promote and maintain excessive dietary sodium intake. Of particular importance are experience-dependent processes including the sensitization of the neural systems underlying sodium appetite and the effects of sodium balance on hedonic state and mood. Accumulating evidence suggests that plasticity within the central nervous system as a result of experience with high salt intake, sodium depletion, or a chronic unresolved sodium appetite fosters enduring changes in sodium related appetitive and consummatory behaviors. PMID:18514747

Mechanism of sodium and chloride transport in the thin ascending limb of Henle.

PubMed Central

Imai, M; Kokko, J P

1976-01-01

Our previous in vitro studies have disclosed that the thin ascending limb of Henle (tALH) possesses some unique membrane characteristics. In those studies we failed to demonstrated active transport of sodium chloride by the tALH, although it was shown that the isotopic permeability to sodium and chloride was unusually high. However, we did not examine the mechanisms by which the apparent high permeation of sodium chloride occurs. Thus the purpose of the present studies was to elucidate the mechanism of sodium chloride transport across the isolated tALH of the rabbit by conducting four different types of studies: (1) comparison of the observed chloride and sodium flux ratios to those predicted by Ussing's equation under imposed salt concentration gradients; (2) kinetic evaluation of chloride and sodium fluxes; (3) examination of the effect of bromide on the kinetics of chloride transport; and (4) experiments to test for the existence of exchange diffusion of chloride. In the first set of studies the predicted and the theoretical flux ratios of sodium were identical in those experiments in which sodium chloride was added either to the perfusate or to the bath. However, the observed chloride flux ratio, lumen-to-bath/bath-to-lumen, was significantly lower than that predicted from Ussing's equation when 100 mM sodium chloride was added to the bath. In the second set of experiments the apparent isotopic permeability for sodium and for chloride was measured under varying perfusate and bath NaCl concentrations. There was no statistical change in the apparent sodium permeability coefficient when the NaCl concentration was raised by varying increments from 85.5 to 309.5 mM. However, permeation of 36Cl decrease significantly with an increase in Cl from 73.6 to 598.6 mM. These events could be explained by a two component chloride transport process consisting of simple diffusion and a saturable facilitated diffusion process with a Vmax = 3.71 neq mm-1 min-1. In the third set of studies it was shown that bromide inhibits transport of chloride and that the magnitude of inhibition is dependent on chloride concentrations. The fourth set of studies ruled out the existence of exchange diffusion. In conclusion, these studies indicate that sodium transport across tALH is by simple passive diffusion, while chloride transport across tALH involves at least two mechanisms: (1) simple passive diffusion; and (2) a specific membrane interaction process (carrier-mediated) which is competitively inhibited by bromide. PMID:993330

The prototype fast reactor at Dounreay, Scotland. Process and engineering development for sodium removal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mann, A.; Herrick, R.; Gunn, J.

2007-07-01

Dounreay was home to commercial fast reactor development in the UK. Following the construction and operation of the Dounreay Fast Reactor, a sodium-cooled Prototype Fast Reactor (PFR), was constructed. PFR started operating in 1974, closed in 1994 and is presently being decommissioned. To date the bulk of the sodium has been removed and treated. Due to the design of the existing extraction system however, a sodium pool will remain in the heel of the reactor. To remove this sodium, a pump/camera system was developed, tested and deployed. The Water Vapour Nitrogen (WVN) process has been selected to allow removal ofmore » the final sodium residues from the reactor. Due to the design of the reactor and potential for structural damage should Normal WVN (which produces hydrated sodium hydroxide) be used, Low Concentration WVN (LC WVN) has been developed. Pilot scale testing has shown that it is possible treat the reactor within 18 months at a WVN concentration of up to 4% v/v and temperature of 120 deg. C. At present the equipment that will be used to apply LC WVN to the reactor is being developed at the detail design stage. and is expected to be deployed within the next few years. (authors)« less

Solidification/stabilization of fly ash from city refuse incinerator facility and heavy metal sludge with cement additives.

PubMed

Cerbo, Atlas Adonis V; Ballesteros, Florencio; Chen, Teng Chien; Lu, Ming-Chun

2017-01-01

Solidification and stabilization are well-known technologies used for treating hazardous waste. These technologies that use cementitious binder have been applied for decades as a final treatment procedure prior to the hazardous waste disposal. In the present work, hazardous waste like fly ash containing high concentrations of heavy metals such Zn (4715.56 mg/kg), Pb (1300.56 mg/kg), and Cu (534.72 mg/kg) and amounts of Ag, Cd, Co, Cr, Mn, and Ni was sampled from a city refuse incinerator facility. This fly ash was utilized in the solidification/stabilization of heavy metal sludge since fly ash has cement-like characteristics. Cement additives such as sodium sulfate, sodium carbonate, and ethylenediaminetetraacetic acid (EDTA) was incorporated to the solidified matrix in order to determine its effect on the solidification/stabilization performance. The solidified matrix was cured for 7, 14, 21, and 28 days prior for its physical and chemical characterizations. The results show that the solidified matrix containing 40% fly ash and 60% cement with heavy metal sludge was the formulation that has the highest fly ash content with a satisfactory strength. The solidified matrix was also able to immobilize the heavy metals both found in the fly ash and sludge based on the toxicity characteristic leaching procedure (TCLP) test. It also shows that the incorporation of sodium carbonate into the solidified matrix not only further improved the compressive strength from 0.36 MPa (without Na 2 CO 3 ) to 0.54 MPa (with Na 2 CO 3 ) but also increased its leaching resistance.

Contribution of food additives to sodium and phosphorus content of diets rich in processed foods.

PubMed

Carrigan, Anna; Klinger, Andrew; Choquette, Suzanne S; Luzuriaga-McPherson, Alexandra; Bell, Emmy K; Darnell, Betty; Gutiérrez, Orlando M

2014-01-01

Phosphorus-based food additives increase the total phosphorus content of processed foods. However, the extent to which these additives augment total phosphorus intake per day is unclear. To examine the contribution of phosphorus-based food additives to the total phosphorus content of processed foods, separate 4-day menus for a low-additive and additive-enhanced diet were developed using Nutrition Data System for Research (NDSR) software. The low-additive diet was designed to conform to U.S. Department of Agriculture guidelines for energy and phosphorus intake (∼2,000 kcal/day and 900 mg of phosphorus per day), and it contained minimally processed foods. The additive-enhanced diet contained the same food items as the low-additive diet except that highly processed foods were substituted for minimally processed foods. Food items from both diets were collected, blended, and sent for measurement of energy and nutrient intake. The low-additive and additive-enhanced diet provided approximately 2,200 kcal, 700 mg of calcium, and 3,000 mg of potassium per day on average. Measured sodium and phosphorus content standardized per 100 mg of food was higher each day of the additive-enhanced diet as compared with the low-additive diet. When averaged over the 4 menu days, the measured phosphorus and sodium contents of the additive-enhanced diet were 606 ± 125 and 1,329 ± 642 mg higher than the low-additive diet, respectively, representing a 60% increase in total phosphorus and sodium content on average. When comparing the measured values of the additive-enhanced diet to NDSR-estimated values, there were no statistically significant differences in measured versus estimated phosphorus contents. Phosphorus and sodium additives in processed foods can substantially augment phosphorus and sodium intake, even in relatively healthy diets. Current dietary software may provide reasonable estimates of the phosphorus content in processed foods. Copyright © 2014 National Kidney Foundation, Inc. Published by Elsevier Inc. All rights reserved.

Application of Solid-State NMR to Reveal Structural Differences in Cefazolin Sodium Pentahydrate from Different Manufacturing Processes

NASA Astrophysics Data System (ADS)

Tian, Ye; Wang, Wei D.; Zou, Wen-Bo; Qian, Jian-Qin; Hu, Chang-Qin

2018-04-01

The solid form of an active pharmaceutical ingredient is important when developing a new chemical entity. A solid understanding of the crystal structure and morphology that affect the mechanical and physical characteristics of pharmaceutical powders determines the manufacturing process. Solid-state NMR, thermogravimetric analysis, X-ray diffraction, and Fourier-transform infrared spectroscopy were combined with theoretical calculation to investigate different crystal packings of α-cefazolin sodium from three different vendors and conformational polymorphism was identified to exist in the α-cefazolin sodium. Marginal differences observed among CEZ-Na pentahydrate 1, 2, and 3 were speculated as the proportion of conformation 2. Understanding the differences in the polymorphic structure of α-cefazolin sodium may help with making modifications to incorporate new knowledge with a product’s development.

Simulation of sodium pumps for nuclear power plants. Technical report 1 Oct 80-1 May 81

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boadu, H.O.

1981-05-01

A single-phase pump model for analysis of transients in sodium cooled fast breeder nuclear power plants has been presented, where homologous characteristic curves are used to predict the behavior of the pump during operating transients. The pump model has been incorporated into BRENDA and FFTF; two system cases to simulate Clinch River Breeder Reactor Plant (CRBRP) and the Fast Flux Test Facility (FFTF) respectively. Two simulation test results for BRENDA which is one loop representation of a three loop plant have been presented. They are: (1) Primary pump coastdown to natural circulation coupled with scram failure, and (2) 10 percentmore » deviation of primary speed with plant controllers incorporated.« less

Effect of sodium ascorbate and sodium nitrite on protein and lipid oxidation in dry fermented sausages.

PubMed

Berardo, A; De Maere, H; Stavropoulou, D A; Rysman, T; Leroy, F; De Smet, S

2016-11-01

The effects of sodium nitrite and ascorbate on lipid and protein oxidation were studied during the ripening process of dry fermented sausages. Samples were taken at day 0, 2, 8, 14, 21 and 28 of ripening to assess lipid (malondialdehyde) and protein (carbonyls and sulfhydryl groups) oxidation. Sodium ascorbate and nitrite were separately able to reduce the formation of malondialdehyde. Their combined addition resulted in higher amounts of carbonyl compounds compared to their separate addition or the treatment without any of both compounds. Moreover, sodium nitrite limited the formation of γ-glutamic semialdehyde whereas sodium ascorbate showed a pro-oxidant effect. A loss of thiol groups was observed during ripening, which was not affected by the use of sodium ascorbate nor sodium nitrite. In conclusion, sodium nitrite and ascorbate affected protein and lipid oxidation in different manners. The possible pro-oxidant effect of their combined addition on carbonyl formation might influence the technological and sensory properties of these products. Copyright © 2016 Elsevier Ltd. All rights reserved.

Green synthesis of gold nanoparticles reduced and stabilized by sodium glutamate and sodium dodecyl sulfate.

PubMed

Cabrera, Gil Felicisimo S; Balbin, Michelle M; Eugenio, Paul John G; Zapanta, Charleo S; Monserate, Juvy J; Salazar, Joel R; Mingala, Claro N

2017-03-18

The Turkevich method has been used for many years in the synthesis of gold nanoparticles. Lately, the use of plant extracts and amino acids has been reported, which is valuable in the field of biotechnology and biomedicine. The AuNPs was synthesized from the reduction of HAuCl4 3H2O by sodium glutamate and stabilized with sodium dodecyl sulfate. The optimum concentrations for sodium glutamate and sodium dodecyl sulfate in the synthesis process were determined. The characteristics of the synthesized AuNPs was analysed through UV-Vis Spectroscopy and SEM. The AuNPs have spherical shape with a mean diameter of approximately 21.62 ± 4.39 nm and is well dispersed. FTIR analysis of the AuNPs reflected that the sulfate head group of sodium dodecyl sulfate is adsorbed at the surface of the AuNPs. Thus, we report herein the synthesis of AuNPs using sodium glutamate and sodium dodecyl sulfate. Copyright © 2017 Elsevier Inc. All rights reserved.

Integrating sodium reduction strategies in the procurement process and contracting of food venues in the County of Los Angeles government, 2010-2012.

PubMed

Cummings, Patricia L; Kuo, Tony; Gase, Lauren N; Mugavero, Kristy

2014-01-01

Since sodium is ubiquitous in the food supply, recent approaches to sodium reduction have focused on increasing the availability of lower-sodium products through system-level and environmental changes. This article reviews integrated efforts by the Los Angeles County Sodium Reduction Initiative to implement these strategies at food venues in the County of Los Angeles government. The review used mixed methods, including a scan of the literature, key informant interviews, and lessons learned during 2010-2012 to assess program progress. Leveraging technical expertise and shared resources, the initiative strategically incorporated sodium reduction strategies into the overall work plan of a multipartnership food procurement program in Los Angeles County. To date, 3 County departments have incorporated new or updated nutrition requirements that included sodium limits and other strategies. The strategic coupling of sodium reduction to food procurement and general health promotion allowed for simultaneous advancement and acceleration of the County's sodium reduction agenda.

Integrating Sodium Reduction Strategies in the Procurement Process and Contracting of Food Venues in the County of Los Angeles Government, 2010–2012

PubMed Central

Cummings, Patricia L.; Kuo, Tony; Gase, Lauren N.; Mugavero, Kristy

2015-01-01

Since sodium is ubiquitous in the food supply, recent approaches to sodium reduction have focused on increasing the availability of lower-sodium products through system-level and environmental changes. This article reviews integrated efforts by the Los Angeles County Sodium Reduction Initiative to implement these strategies at food venues in the County of Los Angeles government. The review used mixed methods, including a scan of the literature, key informant interviews, and lessons learned during 2010–2012 to assess program progress. Leveraging technical expertise and shared resources, the initiative strategically incorporated sodium reduction strategies into the overall work plan of a multipartnership food procurement program in Los Angeles County. To date, 3 County departments have incorporated new or updated nutrition requirements that included sodium limits and other strategies. The strategic coupling of sodium reduction to food procurement and general health promotion allowed for simultaneous advancement and acceleration of the County’s sodium reduction agenda. PMID:24322811

Early oxytocin inhibition of salt intake after furosemide treatment in rats?

PubMed

Core, Sheri L; Curtis, Kathleen S

2017-05-01

Body fluid homeostasis requires a complex suite of physiological and behavioral processes. Understanding of the role of the central nervous system (CNS) in integrating these processes has been advanced by research employing immunohistochemical techniques to assess responses to a variety of body fluid challenges. Such techniques have revealed sex/estrogen differences in CNS activation in response to hypotension and hypernatremia. In contrast, it has been difficult to conclusively identify specific CNS areas and neurotransmitter systems that are activated by hyponatremia using these techniques. In part, this difficulty is due to the temporal disconnect between the physiological effects of treatments commonly used to deplete body sodium and the behavioral response to such depletion. In some methods, sodium ingestion is delayed in association with increased oxytocin (OT), suggesting an inhibitory role for OT in sodium intake. Urinary sodium loss increases within an hour after treatment with furosemide, a natriuretic-diuretic, but sodium intake is delayed for 18-24h. Accordingly, we hypothesized that acute furosemide-induced sodium loss activates centrally-projecting OT neurons which provide an initial inhibition of sodium intake, and tested this hypothesis in ovariectomized Sprague-Dawley rats with or without estrogen using immunohistochemical methods. Neuronal activation in the hypothalamic paraventricular nuclei (PVN) after administration of furosemide corresponded to the timing of the physiological effects. The activation was not different in estrogen-treated rats, nor did estrogen alter the initial suppression of sodium intake. However, virtually no fos immunoreactive (fos-IR) neurons in the parvocellular PVN were also immunolabeled for OT. Thus, acute sodium loss after furosemide produces neural activation and an early inhibition of sodium intake that does not appear to involve activation of centrally-projecting OT neurons and is not influenced by estrogen. Copyright © 2017 Elsevier Inc. All rights reserved.

Preparation of High Purity Crystalline Silicon by Electro-Catalytic Reduction of Sodium Hexafluorosilicate with Sodium below 180°C

PubMed Central

Chen, Yuan; Liu, Yang; Wang, Xin; Li, Kai; Chen, Pu

2014-01-01

The growing field of silicon solar cells requires a substantial reduction in the cost of semiconductor grade silicon, which has been mainly produced by the rod-based Siemens method. Because silicon can react with almost all of the elements and form a number of alloys at high temperatures, it is highly desired to obtain high purity crystalline silicon at relatively low temperatures through low cost process. Here we report a fast, complete and inexpensive reduction method for converting sodium hexafluorosilicate into silicon at a relatively low reaction temperature (∼200°C). This temperature could be further decreased to less than 180°C in combination with an electrochemical approach. The residue sodium fluoride is dissolved away by pure water and hydrochloric acid solution in later purifying processes below 15°C. High purity silicon in particle form can be obtained. The relative simplicity of this method might lead to a low cost process in producing high purity silicon. PMID:25153509

Mechanism of chemical activation of sodium chloride in the presence of amino acids.

PubMed

Rahn, Anja K K; Yaylayan, Varoujan A

2015-01-01

Sodium chloride has been shown to promote chlorination of glycerol during thermal processing. However, the detailed mechanism of this reaction is not well understood. Preliminary experiments have indicated that the reaction mixture should contain an amino acid and it should be dissolved thoroughly in water in order to induce chlorination. These observations are consistent with the process of dissociation of sodium chloride and its re-association with amino acid and eventual formation of the chlorinating agent in the form of the hydrochloride salt. Release of HCl from this salt can be manifested in chlorination and hydrolytic reactions occurring during thermal processing. The generation of HCl at room temperature from a mixture of sodium chloride and glycine was confirmed through spectrophotometric monitoring of the pH. Hydrolytic and chlorination reactions were demonstrated through monitoring of formation of HMF and chlorinated products under pyrolytic conditions using glucose or sucrose and amino acid mixtures. Copyright © 2014 Elsevier Ltd. All rights reserved.

Electrochemical screening of organic and inorganic inhibitors for the corrosion of ASTM A-470 steel in concentrated sodium hydroxide solution

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moccari, A.; MacDonald, D.D.

The corrosion of ASTM A-470 turbine disk steel in concentrated sodium hydroxide solution (10 mol/kg) containing sodium silicate, sodium dihydrogen phosphate, sodium chromate, aniline and some of its derivatives, tannic acid, L-(-)-phenylalanine (aminopropionic acid) and octadecylamine as potential inhibitors has been studied using the potentiodynamic, AC impedance, and Tafel extrapolation techniques. All tests were performed at 115 + or - 2 C. The anodic and cathodic polarization data show that aniline and its derivatives, L-(-)-phenylalanine, NaH/sub 2/PO/sub 4/, Na/sub 2/SiO/sub 3/, and Na/sub 2/CrO/sub 4/ inhibit the anodic process, whereas tannic acid inhibits the cathodic reaction. Octadecylamine was found tomore » inhibit both the anodic and cathodic processes. The mechanisms of inhibition for some of these compounds have been inferred from the wide band width frequency dispersions of the interfacial impedance.« less

Neural control of renal tubular solute and water transport.

PubMed

DiBona, G F

1989-01-01

The neural control of renal tubular solute and water transport is recognized as an important physiological mechanism in the overall regulation of solute and water homeostasis by the mammalian organism. Recent studies have expanded the understanding of this mechanism concerning the transport of diverse solutes with beginning insight into the precise nature of the cellular transport processes involved. The modulatory roles of both circulating and intrarenal hormonal systems on the responses to alterations in the magnitude of efferent renal sympathetic nerve activity are being understood from the nerve terminal release of neurotransmitter to influences on cellular transport processes which determine the overall effect. When dietary sodium intake is normal or only modestly reduced, intact renal innervation is not essential for normal renal sodium conservation. However, when dietary sodium intake is severely restricted, there is maximum engagement of all mechanisms known to participate in renal sodium conservation and, under these conditions, intact renal innervation is essential for normal renal sodium conservation.

Sodium intake and dietary sources of sodium in a sample of undergraduate students from Novi Sad, Serbia.

PubMed

2017-07-01

Data on sodium intake and sources of sodium in the diet in Serbia are limited. The aim of this study was to estimate the sodium intake and identify the sources of sodium in the diet of undergraduate students attending the University of Novi Sad. Students completed a questionnaire to gather data on their gender, age and university faculty attended, and then a 24 h dietary recall. The sodium intake of the students was calculated using the dietary recall data and data on the sodium content of foods. The contribution of different food groups as well as of specific foodstuffs to the total sodium intake was calculated. The mean estimated sodium intake of the students was 3,938.5 ± 1,708.1 mg/day. The sodium intake of 89.1% of the surveyed students exceeded the guideline for sodium intake, the majority of the sodium coming from processed foods (78.9% of the total sodium intake). The food groups that contributed the most to the total sodium intake of the students were meat and meat products (21.7%) and cereals and cereal-based products (18.6%). Bread and other bakery products were responsible for 13.1% of the total sodium intake. High sodium intake in students of the University of Novi Sad puts them at high risk of developing high blood pressure. The food industry should work towards reformulating products with high sodium content, especially bread and other bakery products. Efforts should be taken to reduce sodium intake among undergraduate students in Novi Sad.

Facile synthesis of concentrated gold nanoparticles with low size-distribution in water: temperature and pH controls

NASA Astrophysics Data System (ADS)

Li, Chunfang; Li, Dongxiang; Wan, Gangqiang; Xu, Jie; Hou, Wanguo

2011-07-01

The citrate reduction method for the synthesis of gold nanoparticles (GNPs) has known advantages but usually provides the products with low nanoparticle concentration and limits its application. Herein, we report a facile method to synthesize GNPs from concentrated chloroauric acid (2.5 mM) via adding sodium hydroxide and controlling the temperature. It was found that adding a proper amount of sodium hydroxide can produce uniform concentrated GNPs with low size distribution; otherwise, the largely distributed nanoparticles or instable colloids were obtained. The low reaction temperature is helpful to control the nanoparticle formation rate, and uniform GNPs can be obtained in presence of optimized NaOH concentrations. The pH values of the obtained uniform GNPs were found to be very near to neutral, and the pH influence on the particle size distribution may reveal the different formation mechanism of GNPs at high or low pH condition. Moreover, this modified synthesis method can save more than 90% energy in the heating step. Such environmental-friendly synthesis method for gold nanoparticles may have a great potential in large-scale manufacturing for commercial and industrial demand.

Sodium Flux Growth of Bulk Gallium Nitride

NASA Astrophysics Data System (ADS)

Von Dollen, Paul Martin

This dissertation focused on development of a novel apparatus and techniques for crystal growth of bulk gallium nitride (GaN) using the sodium flux method. Though several methods exist to produce bulk GaN, none have been commercialized on an industrial scale. The sodium flux method offers potentially lower cost production due to relatively mild process conditions while maintaining high crystal quality. But the current equipment and methods for sodium flux growth of bulk GaN are generally not amenable to large-scale crystal growth or in situ investigation of growth processes, which has hampered progress. A key task was to prevent sodium loss or migration from the sodium-gallium growth melt while permitting N2 gas to access the growing crystal, which was accomplished by implementing a reflux condensing stem along with a reusable sealed capsule. The reflux condensing stem also enabled direct monitoring and control of the melt temperature, which has not been previously reported for the sodium flux method. Molybdenum-based materials were identified from a corrosion study as candidates for direct containment of the corrosive sodium-gallium melt. Successful introduction of these materials allowed implementation of a crucible-free containment system, which improved process control and can potentially reduce crystal impurity levels. Using the new growth system, the (0001) Ga face (+c plane) growth rate was >50 mum/hr, which is the highest bulk GaN growth rate reported for the sodium flux method. Omega X-ray rocking curve (?-XRC) measurements indicated the presence of multiple grains, though full width at half maximum (FWHM) values for individual peaks were <100 arcseconds. Oxygen impurity concentrations as measured by secondary ion mass spectroscopy (SIMS) were >1020 atoms/cm3, possibly due to reactor cleaning and handling procedures. This dissertation also introduced an in situ technique to correlate changes in N2 pressure with dissolution of nitrogen and precipitation of GaN from the sodium-gallium melt. Different stages of N2 pressure decay were identified and linked to distinct modes of GaN crystal growth. Based on this analysis, the highest growth rate may have up to 90 mum/hr, and did not appear to be mass-transport limited, in contrast to previous reports. Several refinements and improvements of the novel equipment and methods introduced were also explored, all of which have potential to further advance state of the art sodium flux growth of bulk GaN.

Process for making transition metal nitride whiskers

DOEpatents

Bamberger, C.E.

1988-04-12

A process for making metal nitrides, particularly titanium nitride whiskers, using a cyanide salt as a reducing agent for a metal compound in the presence of an alkali metal oxide. Sodium cyanide, various titanates and titanium oxide mixed with sodium oxide react to provide titanium nitride whiskers that can be used as reinforcement to ceramic composites. 1 fig., 1 tab.

Heat pipe heat transport system for the Stirling Space Power Converter (SSPC)

NASA Technical Reports Server (NTRS)

Alger, Donald L.

1992-01-01

Life issues relating to a sodium heat pipe heat transport system are described. The heat pipe system provides heat, at a temperature of 1050 K, to a 50 kWe Stirling engine/linear alternator power converter called the Stirling Space Power Converter (SSPC). The converter is being developed under a National Aeronautics and Space Administration program. Since corrosion of heat pipe materials in contact with sodium can impact the life of the heat pipe, a literature review of sodium corrosion processes was performed. It was found that the impurity reactions, primarily oxygen, and dissolution of alloy elements were the two corrosion process likely to be operative in the heat pipe. Approaches that are being taken to minimize these corrosion processes are discussed.

Theoretical and experimental studies of the atmospheric sodium layer

NASA Technical Reports Server (NTRS)

Richter, E. S.; Sechrist, C. F., Jr.

1978-01-01

Atmospheric atomic sodium was studied with a laser radar system. Photocount data were processed using a digital filter to obtain continuous estimates of the sodium concentration versus altitude. Wave-like structures in the sodium layer were observed, and there was evidence for the presence of a standing wave in the layer. The bottomside of the layer was observed to undulate with a period of about 2 1/2 hours, and the layer was observed to broaden through the night. A meteor ablation-cluster ion theory of sodium was developed. The theory shows good agreement with existing atmospheric observations as well as laboratory measurements of rate constants.

Nutritional Ways, Means and Myths: Air War College Class 1985

DTIC Science & Technology

1985-05-01

at increased risk for cardiovascular disease. The one problem with cardiovascular disease is that the process may begin at an early age...period. It is during this asymptomatic period that risk factor modifi- cation (diet being one of them) may halt or even reverse the process . Wow...foods high in sodium (Rsmember, the recommended maximum daily intake is two grams or 2000 mg.): mo. sodium Processed meats: 1 oz, ram bacon 1 oz

Human Health Exposure Assessment for Rocky Mountain Arsenal. Volume 3-A. Toxicity Assessment. Version 4.1

DTIC Science & Technology

1990-09-01

and Fate Little information is available on the transport and fate processes of fluoroacetic acid or its sodium salt, sodium fluoroacetate. Both the...the disappearance rate constants for the hydrolytic and photolytic processes . Fate and transport assessment indicates that HCPD will not likely reach...Other sources of atmospheric mercury which include industrial processes , mining and smelting of mercury ones, and combustion of fossil fuels can

Yeast diversity and dynamics in the production processes of Norwegian dry-cured meat products.

PubMed

Asefa, Dereje T; Møretrø, Trond; Gjerde, Ragnhild O; Langsrud, Solveig; Kure, Cathrine F; Sidhu, Maan S; Nesbakken, Truls; Skaar, Ida

2009-07-31

This study investigate the diversity and dynamics of yeasts in the production processes of one unsmoked and two smoked dry-cured meat products of a Norwegian dry-cured meat production facility. A longitudinal observational study was performed to collect 642 samples from the meat, production materials, room installations and indoor and outdoor air of the production facility. Nutrient rich agar media were used to isolate the yeasts. Morphologically different isolates were re-cultivated in their pure culture forms. Both classical and molecular methods were employed for species identification. Totally, 401 yeast isolates belonging to 10 species of the following six genera were identified: Debaryomyces, Candida, Rhodotorula, Rhodosporidium, Cryptococcus and Sporidiobolus. Debaryomyces hansenii and Candida zeylanoides were dominant and contributed by 63.0% and 26.4% respectively to the total isolates recovered from both smoked and unsmoked products. The yeast diversity was higher at the pre-salting production processes with C. zeylanoides being the dominant. Later at the post-salting stages, D. hansenii occurred frequently. Laboratory studies showed that D. hansenii was more tolerant to sodium chloride and nitrite than C. zeylanoides. Smoking seems to have a killing or a temporary growth inhibiting effect on yeasts that extend to the start of the drying process. Yeasts were isolated only from 31.1% of the environmental samples. They belonged to six different species of which five of them were isolated from the meat samples too. Debaryomyces hansenii and Rhodotorula glutinis were dominant with a 62.6% and 22.0% contribution respectively. As none of the air samples contained D. hansenii, the production materials and room installations used in the production processes were believed to be the sources of contamination. The dominance of D. hansenii late in the production process replacing C. zeylanoides should be considered as a positive change both for the quality and safety of the products, as C. zeylanoides has been documented as an emerging pathogen.

Method of preparing silicon from sodium fluosilicate

DOEpatents

Schmidt, Frederick A.; Rehbein, David; Chiotti, Premo

1984-01-01

A process for preparing high purity silicon metal from Na.sub.2 SiF.sub.6 (sodium fluosilicate). The sodium fluosilicate is heated to decomposition temperature to form NaF, which retains most of the impurities, and gaseous SiF.sub.4. The SiF.sub.4 is then reduced by the bomb reduction method using a reductant having a low packing density.

Effect of pH on turbidity, size, viscosity and the shape of sodium caseinate aggregates with light scattering and rheometry.

PubMed

Ghorbani Gorji, Sara; Ghorbani Gorji, Elham; Mohammadifar, Mohammad Amin

2015-03-01

The characterization of sodium caseinate solutions as a function of pH was determined using titration with HCL through turbidimetry in different concentrations (0.03 wt.%, 0.045 wt.%, 0.06 wt.%, 0.09 wt.%, 0.2 wt.%, and 0.3 wt.%). Additionally, the coupling of slow in situ acidification of the solution and rheometry was utilized to gain deeper insights into pH-induced structural transitions during the self assembly process and particle size distribution analysis have been used to determine the behavior of sodium caseinate solutions in different pHs. The formation of aggregates during the acidification process was clearly visualized using microscopy. Surprisingly the viscosity of sodium caseinate solution at pH 4.64 was maximum and decreased by lowering pH. Particle size analysis confirmed the onset of big aggregates on decreasing pH but further acidification led to formation of smaller aggregates. A small concentration effect on pI was seen where at sodium caseinate levels of 0.03 wt.% the pI occurred at 4.29, where at sodium caseinate levels of 0.30 wt.% pI value was 4.64.

40 CFR 415.160 - Applicability; description of the sodium chloride production subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS INORGANIC CHEMICALS MANUFACTURING POINT... the production of sodium chloride by the solution brine-mining process and by the solar evaporation...

Elucidation of the naproxen sodium adsorption onto activated carbon prepared from waste apricot: kinetic, equilibrium and thermodynamic characterization.

PubMed

Onal, Y; Akmil-Başar, C; Sarici-Ozdemir, C

2007-09-30

In this study, activated carbon (WA11Zn5) was prepared from waste apricot, which is waste in apricot plants in Malatya, by chemical activation with ZnCl(2). BET surface area of activated carbon is determined as 1060 m(2)/g. The ability of WA11Zn5, to remove naproxen sodium from effluent solutions by adsorption has been studied. Equilibrium isotherms for the adsorption of naproxen sodium on activated carbon were measured experimentally. Results were analyzed by the Langmiur, Freundlich equation using linearized correlation coefficient at 298 K. The characteristic parameters for each isotherm have been determined. Langmiur equation is found to best represent the equilibrium data for naproxen sodium-WA11Zn5 systems. The monolayer adsorption capacity of WA11Zn5 for naproxen sodium was found to be 106.38 mg/g at 298 K. The process was favorable and spontaneous. The kinetics of adsorption of naproxen sodium have been discussed using three kinetic models, i.e., the pseudo first-order model, the pseudo second-order model, the intraparticle diffusion model. Kinetic parameters and correlation coefficients were determined. It was shown that the pseudo second-order kinetic equation could describe the adsorption kinetics for naproxen sodium onto WA11Zn5. The thermodynamic parameters, such as DeltaG degrees , DeltaS degrees and DeltaH degrees, were calculated. The thermodynamics of naproxen sodium-WA11Zn5 system indicates endothermic process.

Oil removal of spent hydrotreating catalyst CoMo/Al2O3 via a facile method with enhanced metal recovery.

PubMed

Yang, Yue; Xu, Shengming; Li, Zhen; Wang, Jianlong; Zhao, Zhongwei; Xu, Zhenghe

2016-11-15

Deoiling process is a key issue for recovering metal values from spent hydrotreating catalysts. The oils can be removed with organic solvents, but the industrialized application of this method is greatly hampered by the high cost and complex processes. Despite the roasting method is simple and low-cost, it generates hardest-to-recycle impurities (CoMoO4 or NiMoO4) and enormous toxic gases. In this study, a novel and facile approach to remove oils from the spent hydrotreating catalysts is developed. Firstly, surface properties of spent catalysts are characterized to reveal the possibility of oil removal. And then, oils are removed with water solution under the conditions of 90°C, 0.1wt% SDS, 2.0wt% NaOH and 10ml/gL/S ratio for 4h. Finally, thermal treatment and leaching tests are carried out to further explore the advantages of oil removal. The results show that no hardest-to-recycle impurity CoMoO4 is found in XPS spectra of thermally treated samples after deoiling and molybdenum is leached completely with sodium carbonate solution. It means that the proposed deoiling method can not only remove oils simply and without enormous harmful gases generating, but also avoid the generation of detrimental impurity and promote recycling of valuable metals from spent hydrotreating catalysts. Copyright © 2016 Elsevier B.V. All rights reserved.

The role of sodium in the salty taste of permeate.

PubMed

Frankowski, K M; Miracle, R E; Drake, M A

2014-09-01

Many food companies are trying to limit the amount of sodium in their products. Permeate, the liquid remaining after whey or milk is ultrafiltered, has been suggested as a salt substitute. The objective of this study was to determine the sensory and compositional properties of permeates and to determine if elements other than sodium contribute to the salty taste of permeate. Eighteen whey (n=14) and reduced-lactose (n=4) permeates were obtained in duplicate from commercial facilities. Proximate analyses, specific mineral content, and nonprotein nitrogen were determined. Organic acids and nucleotides were extracted followed by HPLC. Aromatic volatiles were evaluated by gas chromatography-mass spectrometry. Descriptive analysis of permeates and model solutions was conducted using a trained sensory panel. Whey permeates were characterized by cooked/milky and brothy flavors, sweet taste, and low salty taste. Permeates with lactose removed were distinctly salty. The organic acids with the highest concentration in permeates were lactic and citric acids. Volatiles included aldehydes, sulfur-containing compounds, and diacetyl. Sensory tests with sodium chloride solutions confirmed that the salty taste of reduced-lactose permeates was not solely due to the sodium present. Permeate models were created with NaCl, KCl, lactic acid, citric acid, hippuric acid, uric acid, orotic acid, and urea; in addition to NaCl, KCl, lactic acid, and orotic acid were contributors to the salty taste. Copyright © 2014 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Investigation of return photons from sodium laser beacon excited by a 40-watt facility-class pulsed laser for adaptive optical telescope applications.

PubMed

Bian, Qi; Bo, Yong; Zuo, Junwei; Li, Min; Dong, Ruoxi; Deng, Keran; Zhang, Dingwen; He, Liping; Zong, Qingshuang; Cui, Dafu; Peng, Qinjun; Chen, Hongbin; Xu, Zuyan

2018-06-15

The brightness of the artificial beacon is one critical performance parameter for adaptive optics. Here, a 40-watt level narrow-linewidth microsecond pulsed yellow laser is produced at 589 nm with a high repetition frequency of 600 Hz and a pulse duration of 120 μs. An experiment to project the pulse beam up to the sky and measure the fluorescence photon returns of the Na atoms has been held on the 1.8-meter telescope in Lijiang observatory. During the sky test, a laser guide star (LGS) spot is firstly observed with Rayleigh scattering elimination by means of a gateable pulse format. And, the central wavelength of the laser could be accurately locked to be 589.1584 nm with a linewidth of ~0.34 GHz to match that of sodium-D 2a line. Optical pumping with circularly polarized light has also been used to increase the brightness of sodium LGS. In order to maximize the return flux, sodium D 2b repumping option is done by an electro-optic modulator with the optimum D 2a -D 2b frequency offset. As a result, a bright sodium LGS with the return flux of 1610 photons/cm 2 /s is achieved, corresponding to ~47 photons/cm 2 /s/W of emitted laser power, which represents a significant improvement in terms of brightness reported ever.

Space Agriculture for Recovery of Fukushima from the Nuclear Disaster

NASA Astrophysics Data System (ADS)

Yamashita, Masamichi; Tomita-Yokotani, Kaori; Hasegawa, Katsuya; Kanazawa, Shinjiro; Oshima, Tairo

2012-07-01

Space agriculture is an engineering challenge to realize life support functions on distant planetary bodies under their harsh environment. After the nuclear disaster in Fukushima, its land was heavily contaminated by radioactive cesium and other nuclei. We proposed the use of space agriculture to remediate the contaminated land. Since materials circulation in the human dominant system should remove sodium from metabolic waste at processing fertilizer for crop plants, handling of sodium and potassium ions in agro-ecosystem has been one of major research targets of space agriculture. Cesium resembles to potassium as alkaline metal. Knowledge on behavior of sodium/potassium in agro-ecosystem might contribute to Fukushima. Reduction of volume of contaminated biomass made by hyperthermophilic aerobic composting bacterial system is another proposal from space agriculture. Volume and mass of plant bodies should be reduced for safe storage of nuclear wastes. Capacity of the storage facility will be definitely limited against huge amount of contaminated soil, plants and others. For this purpose, incineration of biomass first choice. The process should be under the lowered combustion temperature and with filters to confine radioactive ash to prevent dispersion of radioactive cesium. Biological combustion made by hyperthermophilic aerobic composting bacterial system might offer safe alternative for the volume reduction of plant biomass. Scientific evidence are demanded for Fukushima in order to to judge health risks of the low dose rate exposure and their biological mechanism. Biology and medicine for low dose rate exposure have been intensively studied for space exploration. The criteria of radiation exposure for general public should be remained as 1 mSv/year, because people has no merit at being exposed. However, the criteria of 1,200 mSv for life long, which is set to male astronaut, age of his first flight after age 40, might be informative to people for understanding the less risk of low dose rate against the acute exposure of same total dose. Scientific achievements of space radiobiology and medicine help people to assess their risk of exposure to radiation and to find effective measures against it. Knowledge for quantitative comparison of risks need to be provided. Space agriculture is a promising testbed to solve the Fukushima problems.

Characterization and regulation of (/sup 3/H)-serotonin uptake and release in rodent spinal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stauderman, K.A.

1986-01-01

The uptake and release of (/sup 3/H)-serotonin were investigated in rat spinal cord synaptosomes. In the uptake experiments, sodium-dependent and sodium-independent (/sup 3/H)-serotonin accumulation processes were found. Sodium-dependent (/sup 3/H)-serotonin accumulation was: linear with sodium concentrations up to 180 mM; decreased by disruption of membrane integrity or ionic gradients; associated with purified synaptosomal fractions; and reduced after description of descending serotonergic neurons in the spinal cord. Of the uptake inhibitors tested, the most potent was fluoxetine (IC/sub 50/ 75 nM), followed by desipramine (IC/sub 50/ 430 nM) and nomifensine (IC/sub 50/ 950 nM). The sodium-independent (/sup 3/H)-serotonin accumulation process wasmore » insensitive to most treatments and probably represents nonspecific membrane binding. Thus, only sodium-dependent (/sup 3/H)-serotonin uptake represents the uptake process of serotonergic nerve terminals in rat spinal cord homogenates. In the release experiments, K/sup +/-induced release of previously accumulated (/sup 3/H)-serotonin was Ca/sup 2 +/-dependent, and originated from serotonergic synaptosomes. Exogenous serotonin and 5-methyoxy-N,N-dimethyltryptamine inhibited (/sup 3/H)-serotonin release in a concentration-dependent way. Of the antagonists tested, only methiothepin effectively blocked the effect of serotonin. These data support the existence of presynaptic serotonin autoreceptors on serotonergic nerve terminals in the rat spinal cord that act to inhibit a voltage and Ca/sup 2 +/-sensitive process linked to serotonin release. Alteration of spinai cord serotonergic function may therefore be possible by drugs acting on presynaptic serotonin autoreceptors in the spinal cord.« less

21 CFR 201.22 - Prescription drugs containing sulfites; required warning statements.

Code of Federal Regulations, 2012 CFR

2012-04-01

... are added to certain drug products to inhibit the oxidation of the active drug ingredient. Oxidation.... Examples of specific sulfites used to inhibit this oxidation process include sodium bisulfite, sodium...

21 CFR 201.22 - Prescription drugs containing sulfites; required warning statements.

Code of Federal Regulations, 2010 CFR

2010-04-01

... are added to certain drug products to inhibit the oxidation of the active drug ingredient. Oxidation.... Examples of specific sulfites used to inhibit this oxidation process include sodium bisulfite, sodium...

21 CFR 201.22 - Prescription drugs containing sulfites; required warning statements.

Code of Federal Regulations, 2013 CFR

2013-04-01

... are added to certain drug products to inhibit the oxidation of the active drug ingredient. Oxidation.... Examples of specific sulfites used to inhibit this oxidation process include sodium bisulfite, sodium...

21 CFR 201.22 - Prescription drugs containing sulfites; required warning statements.

Code of Federal Regulations, 2011 CFR

2011-04-01

... are added to certain drug products to inhibit the oxidation of the active drug ingredient. Oxidation.... Examples of specific sulfites used to inhibit this oxidation process include sodium bisulfite, sodium...

21 CFR 201.22 - Prescription drugs containing sulfites; required warning statements.

Code of Federal Regulations, 2014 CFR

2014-04-01

... are added to certain drug products to inhibit the oxidation of the active drug ingredient. Oxidation.... Examples of specific sulfites used to inhibit this oxidation process include sodium bisulfite, sodium...

Mineral resource of the month: soda ash

USGS Publications Warehouse

Kostic, Dennis S.

2006-01-01

Soda ash, also known as sodium carbonate, is an alkali chemical that can be refined from the mineral trona and from sodium carbonate-bearing brines. Several chemical processes exist for manufacturing synthetic soda ash.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Poirier, M.; Burket, P.

The Savannah River Site (SRS) is currently treating radioactive liquid waste with the Actinide Removal Process (ARP) and the Modular Caustic Side Solvent Extraction Unit (MCU). Recently, the low filter flux through the ARP of approximately 5 gallons per minute has limited the rate at which radioactive liquid waste can be treated. Salt Batch 6 had a lower processing rate and required frequent filter cleaning. Savannah River Remediation (SRR) has a desire to understand the causes of the low filter flux and to increase ARP/MCU throughput. SRR requested SRNL to conduct bench-scale filter tests to evaluate whether sodium oxalate, sodiummore » aluminosilicate, or aluminum solids (i.e., gibbsite and boehmite) could be the cause of excessive fouling of the crossflow or secondary filter at ARP. The authors conducted the tests by preparing slurries containing 6.6 M sodium Salt Batch 6 supernate, 2.5 g MST/L slurry, and varying concentrations of sodium oxalate, sodium aluminosilicate, and aluminum solids, processing the slurry through a bench-scale filter unit that contains a crossflow primary filter and a dead-end secondary filter, and measuring filter flux and transmembrane pressure as a function of time. Among the conclusions drwn from this work are the following: (1) All of the tests showed some evidence of fouling the secondary filter. This fouling could be from fine particles passing through the crossflow filter. (2) The sodium oxalate-containing feeds behaved differently from the sodium aluminosilicate- and gibbsite/boehmite-containing feeds.« less

Enhanced cyclic stability of SnS microplates with conformal carbon coating derived from ethanol vapor deposition for sodium-ion batteries

NASA Astrophysics Data System (ADS)

Li, Xiang; Liu, Jiangwen; Ouyang, Liuzhang; Yuan, Bin; Yang, Lichun; Zhu, Min

2018-04-01

Carbon coated SnS microplates (SnS@C MPs) were prepared via a facile chemical vapor deposition method using SnS2 nanoflakes as precursor and ethanol vapor as carbon source. The carbon coating restrains the growth of SnS during the heat treatment. Furthermore, it improves the electronic conductivity as well as accommodates volume variations of SnS during the sodiation and desodiation processes. Therefore, the rate capability and cycle performance of the SnS@C MPs as anode materials for sodium-ion batteries are remarkably enhanced compared with the bare SnS and the SnS2 precursor. At current densities of 0.1, 0.2, 0.5, 1 and 2 A g-1, the optimized SnS@C MPs exhibit stable capacities of 602.9, 532.1, 512.2, 465.9 and 427.2 mAh g-1, respectively. At 1 A g-1, they show a reversible capacity of 528.8 mAh g-1 in the first cycle, and maintain 444.7 mAh g-1 after 50 cycles, with capacity retention of 84.1%. The carbon coating through chemical vapor deposition using ethanol vapor as carbon sources is green, simple and cost-effective, which shows great promise to improve the reversible Na+ storage of electrode materials.

An environmentally benign dual action antimicrobial: quaternized chitosan/sodium alga acid multilayer films and silver nanoparticles decorated on magnetic nanoparticles.

PubMed

Jin, Feng; Xiang, Qian; Chen, Xiaoqin; Peng, Xuefeng; Xing, Xiaodong

2016-10-01

There is an urgent need to develop a puissant and environmentally benign antibacterial composite that act via multiple mechanisms to make response to the potentially daunting complexity of the microbial population and microbial antibiotic resistance. In this work, a facile and green approach, layer-by-layer self-assembly technology was applied to assemble polycation quaternized chitosan (QAC) and polyanion sodium alga acid onto magnetic nanoparticles (MNPs). Then silver nanoparticles (AgNPs) with stable and narrow-sized distribution in the range of 25-35 nm were immobilized on the surface of MNPs with L-ascorbic acid as reducing agent and organic multilayers as stabilizer. Through above modification on MNPs, we expected to achieve a green dual antibacterial and recyclable composite via the combined antibacterial action of QAC and AgNPs. Fourier transform infrared spectroscopy, X-ray diffraction, thermogravimetric analysis, transmission electron microscopy, zeta potentials, and dynamic light scattering were employed to confirm the success of the surface functionalization. Silver ion release process was detected by inductively coupled plasma mass spectrometry. Furthermore, the antibacterial properties of the biomaterials against Gram-negative Escherichia coli and Gram-positive Staphylococcus aureus were studied. The modified MNPs exhibited rapid, efficient, and long-lasting biocidal abilities against E. coli and S. aureus. The magnetic antibacterial composite still showed excellent antibacterial efficiency during five exposure/collection/recycle procedures.

Advanced reactors and associated fuel cycle facilities: safety and environmental impacts.

PubMed

Hill, R N; Nutt, W M; Laidler, J J

2011-01-01

The safety and environmental impacts of new technology and fuel cycle approaches being considered in current U.S. nuclear research programs are contrasted to conventional technology options in this paper. Two advanced reactor technologies, the sodium-cooled fast reactor (SFR) and the very high temperature gas-cooled reactor (VHTR), are being developed. In general, the new reactor technologies exploit inherent features for enhanced safety performance. A key distinction of advanced fuel cycles is spent fuel recycle facilities and new waste forms. In this paper, the performance of existing fuel cycle facilities and applicable regulatory limits are reviewed. Technology options to improve recycle efficiency, restrict emissions, and/or improve safety are identified. For a closed fuel cycle, potential benefits in waste management are significant, and key waste form technology alternatives are described. Copyright © 2010 Health Physics Society

Application of steel slag coated with sodium hydroxide to enhance precipitation-coagulation for phosphorus removal.

PubMed

Park, Taejun; Ampunan, Vanvimol; Maeng, Sungkyu; Chung, Eunhyea

2017-01-01

Phosphorus removal has been studied for decades to reduce the environmental impact of phosphorus in natural waterbodies. Slag has been applied for the phosphorus removal by several mechanisms. In this study, sodium hydroxide coating was applied on the slag surface to enhance the efficiency of precipitation-coagulation process. In the batch test, it was found that the capacity of the slag to maintain high pH decreases with increasing its exposure time to the aqueous solution. In the column test, the coarse-grained coated slag showed higher phosphorus removal efficiency than the fine-grained uncoated slag. The coated slag maintained pH higher than uncoated slag and, accordingly, the removal efficiency of phosphorus was higher. Especially, when pH was less than 8, the removal efficiency decreased significantly. However, coated slag provided an excess amount of aluminum and sodium. Thus, a return process to reuse aluminum and sodium as a coagulant was introduced. The return process yields longer lifespan of slag with higher phosphorus removal and lower concentration of cations in the effluent. With the return process, the phosphorus removal efficiency was kept higher than 60% until 150 bed volumes; meanwhile, the efficiency without return process became lower than 60% at 25 bed volumes. Copyright © 2016 Elsevier Ltd. All rights reserved.

Palatability of sous vide processed chicken breast.

PubMed

Turner, B E; Larick, D K

1996-08-01

The influences of brine composition, internal temperature, heating rate, and storage periods up to 28 d on flavor, texture, and color of sous vide processed chicken breast were evaluated. Pectoralis major muscles containing water and sodium chloride, with or without sodium lactate, were browned and vacuum packaged. Sous vide processing was by fast or slow heating to an internal temperature of 77 or 94 C. Product was evaluated after 0, 14, and 28 d storage at 4 C. Quality was evaluated by gas chromatographic analyses of flavor volatiles, shear, color, and sensory panels. Incorporation of sodium lactate into brine did not influence oxidative stability (as measured by headspace gas chromatography) or sensory warmed-over flavor. Presence of sodium lactate did result in enhanced fresh roasted or meaty and saltiness sensory scores as well as a more yellow color. The more rapid heating rate decreased sulfur-containing compounds and did not influence other volatile concentrations. Products processed to 94 C were less juicy, less tender, and contained higher quantities of alcohols and hydrocarbons than those processed to 77 C. Storage resulted in a decline in fresh roasted or meaty flavor note and an increase in warmed-over flavor note and quantities of alcohols, aldehydes and ketones, hydrocarbons, and total headspace volatiles.

Analysis of cadmium in undissolved anode materials of Mark-IV electro-refiner

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yoo, Tae-Sic; Fredrickson, G.L.; Vaden, D.

2013-07-01

The Mark-IV electro-refiner (Mk-IV ER) is a unit process in the FCF (Fuel Conditioning Facility), which is primarily assigned to treating the used driver fuels. Mk-IV ER contains an electrolyte/molten cadmium system for refining uranium electrochemically. Typically, the anode of the Mk-IV ER consists of the chopped sodium-bonded metallic driver fuels, which have been primarily U-10Zr binary fuels. Chemical analysis of the residual anode materials after electrorefining indicates that a small amount of cadmium is removed from the Mk-IV ER along with the undissolved anode materials. Investigation of chemical analysis data indicates that the amount of cadmium in the undissolvedmore » anode materials is strongly correlated with the anode rotation speeds and the residence time of the anode in the Mk-IV ER. Discussions are given to explain the prescribed correlation. (authors)« less

Low-temperature nitridation of manganese and iron oxides using NaNH2 molten salt.

PubMed

Miura, Akira; Takei, Takahiro; Kumada, Nobuhiro

2013-10-21

Manganese and iron nitrides are important functional materials, but their synthesis processes from oxides often require high temperatures. Herein, we show a novel meta-synthesis method for manganese and iron nitrides by low-temperature nitridation of their oxides using NaNH2 molten salt as the nitrogen source in an autoclave at 240 °C. With this method, nitridation of micrometer-sized oxide particles kept their initial morphologies, but the size of the primary particles decreased. The thermodynamic driving force is considered to be the conversion of oxides to sodium hydroxide, and the kinetic of nitridation is improved by the decrease of particle size and the low melting point of NaNH2. This technique as developed here has the advantages of low reaction temperature, reduced consumption of ammonia, employing nonspecialized equipment, and providing facile control of the reactions for producing nitrides from oxides.

Field Comparison of the Sampling Efficacy of Two Smear Media: Cotton Fiber and Kraft Paper

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hogue, M.G.

Two materials were compared in field tests at the Defense Waste Processing Facility: kraft paper (a strong, brown paper made from wood pulp prepared with a sodium sulfate solution) and cotton fiber. Based on a sampling of forty-six pairs of smears, the cotton fiber smears provide a greater sensitivity. The cotton fiber smears collected an average of forty-four percent more beta activity than the kraft paper smears and twenty-nine percent more alpha activity. Results show a greater sensitivity with cotton fiber over kraft paper at the 95 percent confidence level. Regulatory requirements for smear materials are vague. The data demonstratemore » that the difference in sensitivity of smear materials could lead to a large difference in reported results that are subsequently used for meeting shipping regulations or evaluating workplace contamination levels.« less

Investigation of catalytic activity towards oxygen reduction reaction of Pt dispersed on boron doped graphene in acid medium.

PubMed

Pullamsetty, Ashok; Sundara, Ramaprabhu

2016-10-01

Boron doped graphene was prepared by a facile method and platinum (Pt) decoration over boron doped graphene was done in various chemical reduction methods such as sodium borohydride (NaBH4), polyol and modified polyol. X-ray diffraction analysis indicates that the synthesized catalyst particles are present in a nanocrystalline structure and transmission and scanning electron microscopy were employed to investigate the morphology and particle distribution. The electrochemical properties were investigated with the help of the rotating disk electrode (RDE) technique and cyclic voltammetry. The results show that the oxygen reduction reaction (ORR) takes place by a four-electron process. The kinetics of the ORR was evaluated using K-L and Tafel plots. The electrocatalyst obtained in modified polyol reduction method has shown the better catalytic activity compared to other two electrocatalysts. Copyright © 2016 Elsevier Inc. All rights reserved.

Manufacture, distribution, and handling of nitrate salts for solar-thermal applications

NASA Astrophysics Data System (ADS)

Fiorucci, L. C.; Goldstein, S. L.

1982-11-01

The low cost and attractive physical properties of molten sodium/potassium nitrate salts were shown to be one of the most cost effective fluids for heat absorption and thermal energy storage in Solar Central Receiver (SCR) systems. Information related to the availability, transport, handling, and utilization of these salts for commercial size SCR applications is provided. The following items are reviewed: existing manufacturing processes for natural and synthetic nitrates; the upstream availability of raw materials; downstream existing and projected demand for these products in other sectors of the economy; and relevant handling and distribution technologies. Safety considerations and issues more directly related to the SCR facility, such as initial system charging, salt maintenance and regeneration, and disposal are also reviewed. Options for supply, surge storage, and initial charging are discussed for the 1 MWt to 300 MWe range of solar plant sizes.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Natesan, K.; Momozaki, Y.; Li, M.

This report gives a description of the activities in design, fabrication, construction, and assembling of a pumped sodium loop for the sodium compatibility studies on advanced structural materials. The work is the Argonne National Laboratory (ANL) portion of the effort on the work project entitled, 'Sodium Compatibility of Advanced Fast Reactor Materials,' and is a part of Advanced Materials Development within the Reactor Campaign. The objective of this project is to develop information on sodium corrosion compatibility of advanced materials being considered for sodium reactor applications. This report gives the status of the sodium pumped loop at Argonne National Laboratory,more » the specimen details, and the technical approach to evaluate the sodium compatibility of advanced structural alloys. This report is a deliverable from ANL in FY2010 (M2GAN10SF050302) under the work package G-AN10SF0503 'Sodium Compatibility of Advanced Fast Reactor Materials.' Two reports were issued in 2009 (Natesan and Meimei Li 2009, Natesan et al. 2009) which examined the thermodynamic and kinetic factors involved in the purity of liquid sodium coolant for sodium reactor applications as well as the design specifications for the ANL pumped loop for testing advanced structural materials. Available information was presented on solubility of several metallic and nonmetallic elements along with a discussion of the possible mechanisms for the accumulation of impurities in sodium. That report concluded that the solubility of many metals in sodium is low (<1 part per million) in the temperature range of interest in sodium reactors and such trace amounts would not impact the mechanical integrity of structural materials and components. The earlier report also analyzed the solubility and transport mechanisms of nonmetallic elements such as oxygen, nitrogen, carbon, and hydrogen in laboratory sodium loops and in reactor systems such as Experimental Breeder Reactor-II, Fast Flux Test Facility, and Clinch River Breeder Reactor. Among the nonmetallic elements discussed, oxygen is deemed controllable and its concentration in sodium can be maintained in sodium for long reactor life by using cold-trap method. It was concluded that among the cold-trap and getter-trap methods, the use of cold trap is sufficient to achieve oxygen concentration of the order of 1 part per million. Under these oxygen conditions in sodium, the corrosion performance of structural materials such as austenitic stainless steels and ferritic steels will be acceptable at a maximum core outlet sodium temperature of {approx}550 C. In the current sodium compatibility studies, the oxygen concentration in sodium will be controlled and maintained at {approx}1 ppm by controlling the cold trap temperature. The oxygen concentration in sodium in the forced convection sodium loop will be controlled and monitored by maintaining the cold trap temperature in the range of 120-150 C, which would result in oxygen concentration in the range of 1-2 ppm. Uniaxial tensile specimens are being exposed to flowing sodium and will be retrieved and analyzed for corrosion and post-exposure tensile properties. Advanced materials for sodium exposure include austenitic alloy HT-UPS and ferritic-martensitic steels modified 9Cr-1Mo and NF616. Among the nonmetallic elements in sodium, carbon was assessed to have the most influence on structural materials since carbon, as an impurity, is not amenable to control and maintenance by any of the simple purification methods. The dynamic equilibrium value for carbon in sodium systems is dependent on several factors, details of which were discussed in the earlier report. The current sodium compatibility studies will examine the role of carbon concentration in sodium on the carburization-decarburization of advanced structural materials at temperatures up to 650 C. Carbon will be added to the sodium by exposure of carbon-filled iron tubes, which over time will enable carbon to diffuse through iron and dissolve into sodium. The method enables addition of dissolved carbon (without carbon particulates) in sodium that is of interest for materials compatibility evaluation. The removal of carbon from the sodium will be accomplished by exposing carbon-gettering alloys such as refractory metals that have a high partitioning coefficient for carbon and also precipitate carbides, thereby decreasing the carbon concentration in sodium.« less

Offset Initial Sodium Loss To Improve Coulombic Efficiency and Stability of Sodium Dual-Ion Batteries.

PubMed

Ma, Ruifang; Fan, Ling; Chen, Suhua; Wei, Zengxi; Yang, Yuhua; Yang, Hongguan; Qin, Yong; Lu, Bingan

2018-05-09

Sodium dual-ion batteries (NDIBs) are attracting extensive attention recently because of their low cost and abundant sodium resources. However, the low capacity of the carbonaceous anode would reduce the energy density, and the formation of the solid-electrolyte interphase (SEI) in the anode during the initial cycles will lead to large amount consumption of Na + in the electrolyte, which results in low Coulombic efficiency and inferior stability of the NDIBs. To address these issues, a phosphorus-doped soft carbon (P-SC) anode combined with a presodiation process is developed to enhance the performance of the NDIBs. The phosphorus atom doping could enhance the electric conductivity and further improve the sodium storage property. On the other hand, an SEI could preform in the anode during the presodiation process; thus the anode has no need to consume large amounts of Na + to form the SEI during the cycling of the NDIBs. Consequently, the NDIBs with P-SC anode after the presodiation process exhibit high Coulombic efficiency (over 90%) and long cycle stability (81 mA h g -1 at 1000 mA g -1 after 900 cycles with capacity retention of 81.8%), far more superior to the unsodiated NDIBs. This work may provide guidance for developing high performance NDIBs in the future.

Process for making boron nitride using sodium cyanide and boron

DOEpatents

Bamberger, Carlos E.

1990-02-06

This a very simple process for making boron nitride by mixing sodium cyanide and boron phosphate and heating the mixture in an inert atmosphere until a reaction takes place. The product is a white powder of boron nitride that can be used in applications that require compounds that are stable at high temperatures and that exhibit high electrical resistance.

Process for making boron nitride using sodium cyanide and boron

DOEpatents

Bamberger, Carlos E.

1990-01-01

This a very simple process for making boron nitride by mixing sodium cyanide and boron phosphate and heating the mixture in an inert atmosphere until a reaction takes place. The product is a white powder of boron nitride that can be used in applications that require compounds that are stable at high temperatures and that exhibit high electrical resistance.

SP-100 ground engineering system test site description and progress update

NASA Astrophysics Data System (ADS)

Baxter, William F.; Burchell, Gail P.; Fitzgibbon, Davis G.; Swita, Walter R.

1991-01-01

The SP-100 Ground Engineering System Test Site will provide the facilities for the testing of an SP-100 reactor, which is technically prototypic of the generic design for producing 100 kilowatts of electricity. This effort is part of the program to develop a compact, space-based power system capable of producing several hundred kilowatts of electrical power. The test site is located on the U.S. Department of Energy's Hanford Site near Richland, Washington. The site is minimizing capital equipment costs by utilizing existing facilities and equipment to the maximum extent possible. The test cell is located in a decommissioned reactor containment building, and the secondary sodium cooling loop will use equipment from the Fast Flux Test Facility plant which has never been put into service. Modifications to the facility and special equipment are needed to accommodate the testing of the SP-100 reactor. Definitive design of the Ground Engineering System Test Site facility modifications and systems is in progress. The design of the test facility and the testing equipment will comply with the regulations and specifications of the U.S. Department of Energy and the State of Washington.

Water Softeners: How Much Sodium Do They Add?

MedlinePlus

... away the saltshaker and cutting back on processed foods. With Sheldon G. Sheps, M.D. Drinking water advisory: Consumer acceptability advice and health effects analysis on sodium. U.S. Environmental Protection Agency. http://www. ...

The xylooligosaccharide addition and sodium reduction in requeijão cremoso processed cheese.

PubMed

Ferrão, Luana L; Ferreira, Marcus Vinícius S; Cavalcanti, Rodrigo N; Carvalho, Ana Flávia A; Pimentel, Tatiana C; Silva, Hugo L A; Silva, Ramon; Esmerino, Erick A; Neto, Roberto P C; Tavares, Maria Inês B; Freitas, Mônica Q; Menezes, Jaqueline C V; Cabral, Lúcio M; Moraes, Jeremias; Silva, Márcia C; Mathias, Simone P; Raices, Renata S L; Pastore, Gláucia M; Cruz, Adriano G

2018-05-01

The addition of xylooligosaccharide (XOS), sodium reduction and flavor enhancers (arginine and yeast extract) on the manufacture of requeijão cremoso processed cheese was investigated. The addition of XOS resulted in a denser and compact structure, with increased apparent viscosity, elasticity (G') and firmness (G*). The addition of XOS and yeast extract improved the rheological and physicochemical properties (decrease in viscosity and particle size and increase in melting rate) and sensory characteristics (improvement in salty and acid taste, greater homogeneity, and lower bitter taste). In addition, a positive effect of arginine was observed in the sensory characteristics of the requeijão cremoso processed cheese, but without improvements in the physicochemical and rheological characteristics. Overall, the XOS addition and sodium reduction proportionated the development of a healthier processed cheese formulation. Copyright © 2018 Elsevier Ltd. All rights reserved.

Conversion of Carbon Dioxide into Ethanol by Electrochemical Synthesis Method Using Cu-Zn Electrode

NASA Astrophysics Data System (ADS)

Riyanto; Ramadan, S.; Fariduddin, S.; Aminudin, A. R.; Hayatri, A. K.

2018-01-01

Research on conversion of carbon dioxide into ethanol has been done. The conversion process is carried out in a sodium bicarbonate electrolyte solution in an electrochemical synthesis reactor. As cathode was used Cu-Zn, while as anode carbon was utilized. Variations of voltage, concentration of sodium bicarbonate electrolyte solution and time of electrolysis were performed to determine the optimum conditions to convert carbon dioxide into ethanol. Sample of the electrochemical synthesis process was analyzed by gas chromatography. From the result, it is found that the optimum conditions of the electrochemical synthesis process of carbon dioxide conversion into ethanol are voltage, concentration of sodium bicarbonate electrolyte solution and time of electrolysis are 3 volts, 0.4 M and 90 minutes with the ethanol concentration of 10.44%.

MWCNT Coated Free-Standing Carbon Fiber Fabric for Enhanced Performance in EMI Shielding with a Higher Absolute EMI SE

PubMed Central

Pothupitiya Gamage, Sudesh Jayashantha; Yang, Kihun; Braveenth, Ramanaskanda; Raagulan, Kanthasamy; Kim, Hyun Suk; Lee, Yun Seon; Yang, Cheol-Min; Moon, Jai Jung; Chai, Kyu Yun

2017-01-01

A series of multi-walled carbon nanotube (MWCNT) coated carbon fabrics was fabricated using a facile dip coating process, and their performance in electrical conductivity, thermal stability, tensile strength, electromagnetic interference (EMI) and shielding effectiveness (SE) was investigated. A solution of MWCNT oxide and sodium dodecyl sulfate (SDS) in water was used in the coating process. MWCNTs were observed to coat the surfaces of carbon fibers and to fill the pores in the carbon fabric. Electrical conductivity of the composites was 16.42 S cm−1. An EMI shielding effectiveness of 37 dB at 2 GHz was achieved with a single layer of C/C composites, whereas the double layers resulted in 68 dB EMI SE at 2.7 GHz. Fabricated composites had a specific SE of 486.54 dB cm3 g−1 and an absolute SE of approximately 35,000 dB cm2 g−1. According to the above results, MWCNT coated C/C composites have the potential to be used in advanced shielding applications such as aerospace and auto mobile electronic devices.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marlow, D.A.; Fingerhut, M.A.; Piacitelli, L.A.

Information was collected concerning the Monsanto Company, Nitro, West Virginia, for the purpose of evaluating the procedures and the data available to determine if this company would be suitable for inclusion in a study of the causes of death among workers exposed to products contaminated with 2,3,7,8-tetrachlorodibenzo-p-dioxin (TCDD) or hexachlorodibenzo-p-dioxins (HxCDD). Sodium-2,4,5-trichlorophenate (Na-2,4,5-TCP) and 2,4,5-trichlorophenoxyacetic-acid (2,4,5-T-acid) were produced at the facility, and both compounds have been shown to be contaminated with TCDD. Based on the information gathered from Monsanto concerning Na-2,4,5-TCP and 2,4,5-T-acid production processes, the workers involved were suitable for inclusion in the NIOSH Dioxin Registry study. Work historiesmore » for these workers could be constructed. Descriptions of the tasks performed in the various processes through the years were available. Analytical data was available for the years 1958 through 1969 and could be combined with the work histories, the knowledge of the tasks performed, and the concentration of TCDD in the 2,4,5-T-acid.« less

APPLICATION OF VACUUM SALT DISTILLATION TECHNOLOGY FOR THE REMOVAL OF FLUORIDE AND CHLORIDE FROM LEGACY FISSILE MATERIALS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pierce, R.; Peters, T.

2011-11-01

Between September 2009 and January 2011, the Savannah River National Laboratory (SRNL) and the Savannah River Site (SRS) HB-Line Facility designed, developed, tested, and successfully deployed a production-scale system for the distillation of sodium chloride (NaCl) and potassium chloride (KCl) from plutonium oxide (PuO{sub 2}). Subsequent efforts adapted the vacuum salt distillation (VSD) technology for the removal of chloride and fluoride from less-volatile halide salts at the same process temperature and vacuum. Calcium chloride (CaCl{sub 2}), calcium fluoride (CaF{sub 2}), and plutonium fluoride (PuF{sub 3}) were of particular concern. To enable the use of the same operating conditions for themore » distillation process, SRNL employed in situ exchange reactions to convert the less-volatile halide salts to compounds that facilitated the distillation of halide without removal of plutonium. SRNL demonstrated the removal of halide from CaCl{sub 2}, CaF{sub 2} and PuF{sub 3} below 1000 C using VSD technology.« less

Charged Particle Identification for Prefragmentation Studies

NASA Astrophysics Data System (ADS)

Hu, Jonathan; MoNA Collaboration

2017-09-01

Projectile fragmentation refers to high energy (>50 MeV/u) heavy ion beams on production targets to generate intermediate mass and target fragments at facilities like the NSCL, FRIB, GSI, GANIL and RIKEN. The resulting secondary beams can then be isolated by fragment separators like the NCSL's A1900 and that secondary beam then used on reaction targets for a variety of experiments. Predictions of beam intensities for experiment planning depend on models and data. The MoNA Collaboration performed an experiment at the NSCL in which a 48Ca primary beam was used with a 9Be target to produce a 32Mg secondary beam with energy 86 MeV/u that was incident on a second target of 9Be. By characterizing the energy distributions of final fragments of neon, sodium, and fluorine in coincidence with neutrons created both by prefragmentation processes and reaction mechanisms, we are able to extract information about prefragmentation dynamics. The identification of charged fragments is a multi-step process crucial to this analysis. This work is supported by the National Science Foundation under Grant No. PHY-1613429.

In vivo screening of candidate pretreatment compounds against cyanide using mice

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kiser, R.C.; Olson, C.T.; Menton, R.G.

1993-05-13

An in vivo screening procedure was established at Battelle's Medical Research and Evaluation Facility (MREF) to evaluate the efficacy of candidate pretreatment compounds in mice challenged with the blood agent, sodium cyanide (NaCN). Male albino mice of ICR outbred stock weighing between 22.5 and 27.5 g are challenged by intramuscular (i.m.) injection, at a volume of 0.5 mL/kg, of a dose of NaCN twice the LD50 of untreated mice as determined on that day of testing. Candidate drugs are tested at fractions of their LD50 or their limit of solubility in the most optimum vehicle and given intraperitoneally (i.p.) tomore » separate groups of mice at either 60 or 15 min prior to NaCN challenge. Sodium thiosulfate (1000 mg/kg)/sodium nitrite (100 mg/kg) controls are injected i.p. only at 60 min prior to challenge. A test compound is deemed effective if, at any of three concentrations tested, or at either pretreatment time, it is statistically more efficacious in preventing lethality than is a negative control substance (candidate compound vehicle).« less

N/S Co-Doped 3 D Porous Carbon Nanosheet Networks Enhancing Anode Performance of Sodium-Ion Batteries.

PubMed

Zou, Lei; Lai, Yanqing; Hu, Hongxing; Wang, Mengran; Zhang, Kai; Zhang, Peng; Fang, Jing; Li, Jie

2017-10-12

A facile and scalable method is realized for the in situ synthesis of N/S co-doped 3 D porous carbon nanosheet networks (NSPCNNs) as anode materials for sodium-ion batteries. During the synthesis, NaCl is used as a template to prepare porous carbon nanosheet networks. In the resultant architecture, the unique 3 D porous architecture ensures a large specific surface area and fast diffusion paths of both electrons and ions. In addition, the import of N/S produces abundant defects, increased interlayer spacings, more active sites, and high electronic conductivity. The obtained products deliver a high specific capacity and excellent long-term cycling performance, specifically, a capacity of 336.2 mA h g -1 at 0.05 A g -1 , remaining as large as 214.9 mA h g -1 after 2000 charge/discharge cycles at 0.5 A g -1 . This material has great prospects for future applications of scalable, low-cost, and environmentally friendly sodium-ion batteries. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Habit plane-driven P2-type manganese-based layered oxide as long cycling cathode for Na-ion batteries

NASA Astrophysics Data System (ADS)

Luo, Rui; Wu, Feng; Xie, Man; Ying, Yao; Zhou, Jiahui; Huang, Yongxin; Ye, Yusheng; Li, Li; Chen, RenJie

2018-04-01

Layered transition metal oxides are considered to be promising candidates as cathode materials for sodium-ion batteries. Herein, a facile solid-state reaction is developed to synthesize hexagons plate-like Na0.67Ni0.25Mn0.75O2+δ (denoted as P2-NNM) material with habit plane formed. The structure of this layered oxide is characterized by XRD, HR-TEM and SAED. The layered material delivers a high reversible capacity of 91.8 mAh g-1 at 0.2 C with a capacity retention of 94.4 % after 280 cycles, superior rate capability and long cycle life (84.2 % capacity retention after 1000 cycle). Ni2+ is an active ion and Ni doping alleviates the Jahn-Teller distortion, and Mn3+/Mn4+ coexist as Mn4+ is desired from the stability perspective. Particularly, CV and XPS results confirm these results. Moreover, the electrode exhibits a quasi-solid-solution reaction during the sodium extraction and insertion. This contribution demonstrates that P2-NNM is a promising cathode electrode for rechargeable long-life sodium-ion batteries.

Sodium dietary restriction, knowledge, beliefs, and decision-making behavior of older females.

PubMed

Sheahan, Sharon L; Fields, Becky

2008-04-01

The purposes of this qualitative/descriptive study were to (a) explore experiences and decision-making behaviors associated with adoption of a sodium-restricted diet (SRD) among older women with hypertension or heart failure and (b) identify healthcare system and contextual factors that facilitate or impede adherence to SRD. Participants were 33 single older women, aged 65-98 years, residing in three congregate living facilities in the high-risk "coronary valley" area of the United States. A semistructured interview format was employed with three focus groups. The audio-taped transcribed data were content analyzed for themes by the researchers with the assistance of ATLAS.Ti computer software. Predominant themes were lack of SRD education by healthcare providers, a desire for more information about sodium, including the use of alternative herbal seasonings, and large-print informational materials. Eating alone with no motivation to cook and share meals was a contextual barrier to healthy nutrition. To prevent costly hospitalizations and rehospitalization from nonadherence to SRD, clinicians need to provide more structured SRD education supplemented with printed brochures. Exploring the client's nutritional social setting may improve SRD adherence.

Silver nanoparticles-containing dual-function hydrogels based on a guar gum-sodium borohydride system

PubMed Central

Dai, Lei; Nadeau, Ben; An, Xingye; Cheng, Dong; Long, Zhu; Ni, Yonghao

2016-01-01

Dual-function hydrogels, possessing both stimuli-responsive and self-healing properties, have recently attracted attention of both chemists and materials scientists. Here we report a new paradigm using natural polymer (guar gum, GG) and sodium borohydride (NaBH4), for the preparation of silver nanoparticles (AgNPs)-containing smart hydrogels in a simple, fast and economical way. NaBH4 performs as a reducing agent for AgNPs synthesis using silver nitrate (AgNO3) as the precursor. Meanwhile, sodium metaborate (NaBO2) (from NaBH4) behaves as a cross-linking agent between GG molecular chains. The AgNPs/GG hydrogels with excellent viscoelastic properties can be obtained within 3 min at room temperature without the addition of other cross-linkers. The resultant AgNPs/GG hydrogels are flowable and injectable, and they possess excellent pH/thermal responsive properties. Additionally, they exhibit rapid self-healing capacity. This work introduces a facile and scale-up way to prepare a class of hydrogels that can have great potential to biomedical and other industrial applications. PMID:27819289

Analytical study of the liquid phase transient behavior of a high temperature heat pipe. M.S. Thesis

NASA Technical Reports Server (NTRS)

Roche, Gregory Lawrence

1988-01-01

The transient operation of the liquid phase of a high temperature heat pipe is studied. The study was conducted in support of advanced heat pipe applications that require reliable transport of high temperature drops and significant distances under a broad spectrum of operating conditions. The heat pipe configuration studied consists of a sealed cylindrical enclosure containing a capillary wick structure and sodium working fluid. The wick is an annular flow channel configuration formed between the enclosure interior wall and a concentric cylindrical tube of fine pore screen. The study approach is analytical through the solution of the governing equations. The energy equation is solved over the pipe wall and liquid region using the finite difference Peaceman-Rachford alternating direction implicit numerical method. The continuity and momentum equations are solved over the liquid region by the integral method. The energy equation and liquid dynamics equation are tightly coupled due to the phase change process at the liquid-vapor interface. A kinetic theory model is used to define the phase change process in terms of the temperature jump between the liquid-vapor surface and the bulk vapor. Extensive auxiliary relations, including sodium properties as functions of temperature, are used to close the analytical system. The solution procedure is implemented in a FORTRAN algorithm with some optimization features to take advantage of the IBM System/370 Model 3090 vectorization facility. The code was intended for coupling to a vapor phase algorithm so that the entire heat pipe problem could be solved. As a test of code capabilities, the vapor phase was approximated in a simple manner.

Structural characterization of layered Na0.5Co0.5Mn0.5O2 material as a promising cathode for sodium-ion batteries

NASA Astrophysics Data System (ADS)

Manikandan, Palanisamy; Heo, Seongwoo; Kim, Hyun Woo; Jeong, Hu Young; Lee, Eungje; Kim, Youngsik

2017-09-01

Layered Na0.5Co0.5Mn0.5O2 material is synthesized through a facile mixed hydroxy-carbonate route using (Co0.5Mn0.5)2(OH)2CO3 precursor and well characterized as a hexagonal layered structure under P63/mmc space group. The lattice parameters and unit cell volume (a = 2.8363 Å, c = 11.3152 Å and V = 78.83 Å3) are calculated by Rietveld refinement analysis. A flaky-bundle morphology is obtained to the layered Na0.5Co0.5Mn0.5O2 material with the hexagonal flake size ∼30 nm. Advanced transmission electron microscopic images are revealed the local structure of the layered Na0.5Co0.5Mn0.5O2 material with contrasting bright dots and faint dark dots corresponding to the Co/Mn and Na atoms. Two oxidation and reduction peaks are occurred in a cyclic voltammetric analysis corresponding to Co3+/Co4+ and Mn3+/Mn4+ redox processes. These reversible processes are attributed to the intercalation/de-intercalation of Na+ ions into the host structure of layered Na0.5Co0.5Mn0.5O2 material. Accordingly, the sodium cell is delivered the initial charge-discharge capacity 53/144 mAh g-1 at 0.5 C, which cycling studies are extended to rate capability test at 1 C, 3 C and 5C. Eventually, the Na-ion full-cell is yielded cathode charge-discharge capacity 55/52 mAh g-1 at 0.212 mA and exhibited as a high voltage cathode for Na-ion batteries.

Effect of number and washing solutions on functional properties of surimi-like material from duck meat.

PubMed

Ramadhan, Kurnia; Huda, Nurul; Ahmad, Ruzita

2014-02-01

Duck meat is less utilized than other meats in processed products because of limitations of its functional properties, including lower water holding capacity, emulsion stability, and higher cooking loss compared with chicken meat. These limitations could be improved using surimi technology, which consists of washing and concentrating myofibrillar protein. In this study, surimi-like materials were made from duck meat using two or three washings with different solutions (tap water, sodium chloride, sodium bicarbonate, and sodium phosphate buffer). Better improvement of the meat's functional properties was obtained with three washings versus two washings. Washing with tap water achieved the highest gel strength; moderate elevation of water holding capacity, pH, lightness, and whiteness; and left a small amount of fat. Washing with sodium bicarbonate solution generated the highest water holding capacity and pH and high lightness and whiteness values, but it resulted in the lowest gel strength. Processing duck meat into surimi-like material improves its functional properties, thereby making it possible to use duck meat in processed products.

Recovery of heavy metals from spent Ni-Cd batteries by a potentiostatic electrodeposition technique

NASA Astrophysics Data System (ADS)

Yang, Chun-Chen

Two heavy metals, Cd and Ni, have been separately recovered from spent AA-size Ni-Cd batteries by the potentiostatic electrodeposition and chemical precipitation methods, respectively. Various types and concentrations of HCl, H 2SO 4, and HNO 3 acids had been used as leach extractants. Experimental results indicate that the acid with the best leach capability is 4 M HCl. Three complexing reagents of NH 3, sodium acetate, sodium citrate have been chosen and tested. The most effective buffer is sodium citrate. The optimum mole ratio of metallic ion to citrate ion is 1:1. The recovery process for Cd metal is conducted by the potentiostatic electrodeposition in a leach electrolyte with a sodium citrate complex. The optimum applied potential for Cd recovery is in the range -1100 to -1120 mV (versus saturated calomel electrode (SCE)). The current efficiency for the recovery process is between 70 and 90% and depends strongly on the process parameters, e.g. liquor, concentration, applied potential, temperature, type of complex reagents, mole ratio, mass-transfer rate.

Acifluorfen, sodium

Integrated Risk Information System (IRIS)

Acifluorfen , sodium ; CASRN 62476 - 59 - 9 Human health assessment information on a chemical substance is included in the IRIS database only after a comprehensive review of toxicity data , as outlined in the IRIS assessment development process . Sections I ( Health Hazard Assessments for Noncarcino

Sodium fluoroacetate

Integrated Risk Information System (IRIS)

Sodium fluoroacetate ; CASRN 62 - 74 - 8 Human health assessment information on a chemical substance is included in the IRIS database only after a comprehensive review of toxicity data , as outlined in the IRIS assessment development process . Sections I ( Health Hazard Assessments for Noncarcinogen

Sodium diethyldithiocarbamate

Integrated Risk Information System (IRIS)

Sodium diethyldithiocarbamate ; CASRN 148 - 18 - 5 Human health assessment information on a chemical substance is included in the IRIS database only after a comprehensive review of toxicity data , as outlined in the IRIS assessment development process . Sections I ( Health Hazard Assessments for Non

Collaboration Between Environmental Water Chemistry Students and Hazardous Waste Treatment Specialists on the University of Colorado-Boulder Campus

NASA Astrophysics Data System (ADS)

Dittrich, T. M.

2012-12-01

The University of Colorado-Boulder is one of a few universities in the country that has a licensed Treatment, Storage, and Disposal Facility (TSDF) for hazardous waste on campus. This facility, located on the bottom floor of the Environmental Health and Safety (EH&S) building, allows CU to more economically treat hazardous waste by enabling treatment specialists on staff to safely collect and organize the hazardous waste generated on campus. Hazardous waste is anything that contains a regulated chemical or compound and most chemicals used in engineering labs (e.g., acids, solvents, metal solutions) fall into this category. The EH&S staff is able to treat close almost 33% of the waste from campus and the rest is packed for off-site treatment at various places all over the country for disposal (e.g., Sauget, IL, Port Aurthor, TX). The CU-Boulder campus produced over 50 tons of hazardous waste in 2010 costing over $300,000 in off-campus expenses. The EH&S staff assigns one of over 50 codes to the waste which will determine if the waste can be treated on campus of must be shipped off campus to be disposed of. If the waste can be treated on campus, it will undergo one of three processes: 1) neutralization, 2) UV-ozone oxidation, or 3) ion exchange. If the waste is acidic but contains no heavy metals, the acid is neutralized with sodium hydroxide (a base) and can be disposed "down the drain" to the Boulder Wastewater Treatment Plant. If the waste contains organic compounds and no metals, a UV-ozone oxidation system is used to break down the organic compounds. Silver from photography wastewater can be removed using ion exchange columns. Undergraduate and graduate students worked with the hazardous waste treatment facility at the Environmental Health and Safety (EH&S) building on the CU-Boulder campus during the fall of 2011 and fall of 2012. Early in the semester, students receive a tour of the three batch treatment processes the facility is equipped with. Later in the semester, the students conduct a bench-scale laboratory exercise where they study part of the treatment process. Several small start-up companies are testing components in the lab, which adds to the colaboration of the project.; Figure 1. Students in Environmental Water Chemistry lab conducting a titration.

Lidar observations of wave-like structure in the atmospheric sodium layer

NASA Technical Reports Server (NTRS)

Rowlett, J. R.; Gardner, C. S.; Richter, E. S.; Sechrist, C. F., Jr.

1978-01-01

The University of Illinois (Urbana) lidar system has been developed to study the atmospheric sodium layer near 90 km altitude through the mechanism of resonance scattering. The photocount data are processed using digital smoothing filters to obtain continuous estimates of the sodium density versus altitude. The filter cutoff frequency is related to the height resolution and accuracy of the estimated profile. Lidar photocount data processed using this filtering technique show wave-like structures in the sodium layer which move downward with time. The waves have typical wavelengths of 3-15 km and phase velocities of less than 1 m/sec. The movement of these structures seems to be independent of the motion of the bottomside of the layer, which also has been observed to move up or down by as much as 2 km over a period of a few hours.

Modified Graphene Oxide for Long Cycle Sodium-Ion Batteries

NASA Astrophysics Data System (ADS)

Shareef, Muhamed; Gunn, Harrison; Voigt, Victoria; Singh, Gurpreet

Hummer's process was modified to produce gram levels of 2-dimensional nanosheets of graphene oxide (GO) with varying degree of exfoliation and chemical functionalization. This was achieved by varying the weight ratios and reaction times of oxidizing agents used in the process. Based on Raman and Fourier transform infra red spectroscopy we show that potassium permanganate (KMnO4) is the key oxidizing agent while sodium nitrate (NaNO3) and sulfuric acid (H2SO4) play minor role during the exfoliation of graphite. Tested as working electrode in sodium-ion half-cell, the GO nanosheets produced using this optimized approach showed high rate capability and exceptionally high energy density of ~500 mAh/g for up to at least 100 cycles, which is among the highest reported for sodium/graphite electrodes. The average Coulombic efficiency was approximately 99 %. NSF Grant No. 1454151.

Current variability of clinical practice management of pediatric diabetic ketoacidosis in Illinois pediatric emergency departments.

PubMed

Barrios, Ellen K; Hageman, Joseph; Lyons, Evelyn; Janies, Kathryn; Leonard, Daniel; Duck, Stephen; Fuchs, Susan

2012-12-01

This study aimed to investigate the management of pediatric patients with diabetic ketoacidosis (DKA) presenting to emergency departments (EDs) participating in the Illinois Emergency Medical Services for Children (EMSC) Facility Recognition program. In 2010, Illinois EMSC conducted a survey (including case scenarios) and medical record review regarding management of pediatric patients with DKA. Data were submitted by 116 EDs. Survey response rate was 94%. Only 34% of EDs had a documented DKA guideline/policy; 37% reported that they did not have hospital adult or pediatric endocrinology services. Case scenarios identified a high percentage of respondents given an intravenous (IV) isotonic sodium chloride solution of 10 to 20 mL/kg during the first hour. However 17% to 21% would use an alternative choice such as administering initial IV solution of 0.45 sodium chloride, initiating an insulin drip before fluids, or waiting for more laboratory results before giving fluids or insulin. A total of 532 medical record reviews were submitted. In 87% of records, patients received an initial IV isotonic sodium chloride solution within the first hour. In 74%, patients received IV insulin infusion/drip (0.1 U/kg/h) after the initial fluid bolus. Of the patients, 51% were transferred to another facility; 22% were admitted to an intensive care unit. Best ED practice management of pediatric DKA includes establishing a specific guideline/protocol and ensuring access to a pediatric endocrinologist. Both were identified as improvement areas in this project. Illinois EMSC has developed an educational module and provided direct feedback to all participating EDs, to improve their management of pediatric patients with DKA.

YIELD STRESS REDUCTION OF DWPF MELTER FEED SLURRIES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stone, M; Michael02 Smith, M

2006-12-28

The Defense Waste Processing Facility (DWPF) at the Savannah River Site vitrifies High Level Waste for repository internment. The process consists of three major steps: waste pretreatment, vitrification, and canister decontamination/sealing. The HLW consists of insoluble metal hydroxides (primarily iron, aluminum, magnesium, manganese, and uranium) and soluble sodium salts (carbonate, hydroxide, nitrite, nitrate, sulfate). The pretreatment process acidifies the sludge with nitric and formic acids, adds the glass formers as glass frit, then concentrates the resulting slurry to approximately 50 weight percent (wt%) total solids. This slurry is fed to the joule-heated melter where the remaining water is evaporated followedmore » by calcination of the solids and conversion to glass. The Savannah River National Laboratory (SRNL) is currently assisting DWPF efforts to increase throughput of the melter. As part of this effort, SRNL has investigated methods to increase the solids content of the melter feed to reduce the heat load required to complete the evaporation of water and allow more of the energy available to calcine and vitrify the waste. The process equipment in the facility is fixed and cannot process materials with high yield stresses, therefore increasing the solids content will require that the yield stress of the melter feed slurries be reduced. Changing the glass former added during pretreatment from an irregularly shaped glass frit to nearly spherical beads was evaluated. The evaluation required a systems approach which included evaluations of the effectiveness of beads in reducing the melter feed yield stress as well as evaluations of the processing impacts of changing the frit morphology. Processing impacts of beads include changing the settling rate of the glass former (which effects mixing and sampling of the melter feed slurry and the frit addition equipment) as well as impacts on the melt behavior due to decreased surface area of the beads versus frit. Beads were produced from the DWPF process frit by fire polishing. The frit was allowed to free fall through a flame, then quenched with a water spray. Approximately 90% of the frit was converted to beads by this process, as shown in Figure 1. Borosilicate beads of various diameters were also procured for initial testing.« less

The Effect of Smear Layer Removal on Endodontic Outcomes

DTIC Science & Technology

2012-06-01

Sundqvist G. The antibacterial effect of sodium hypochlorite and EDTA in 60 cases of endodontic therapy. Int Endod J 1985;18:35-40. 11. Conner DA, Caplan...outcomes. KEY WORDS: Smear layer, smear layer removal, smear layer creation, EDTA, Sodium hypochlorite , Periapical index INTRODUCTION: The...identified the most efficient process for removal of the smear layer. Normal saline and sodium hypochlorite (NaOCl) have been shown not to remove

Ultrafast and Highly Reversible Sodium Storage in Zinc-Antimony Intermetallic Nanomaterials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nie, Anmin; Gan, Li-yong; Cheng, Yingchun

2015-12-17

The progress on sodium-ion battery technology faces many grand challenges, one of which is the considerably lower rate of sodium insertion/deinsertion in electrode materials due to the larger size of sodium (Na) ions and complicated redox reactions compared to the lithium-ion systems. Here, it is demonstrated that sodium ions can be reversibly stored in Zn-Sb intermetallic nanowires at speeds that can exceed 295 nm s -1. Remarkably, these values are one to three orders of magnitude higher than the sodiation rate of other nanowires electrochemically tested with in situ transmission electron micro­scopy. It is found that the nanowires display aboutmore » 161% volume expansion after the first sodiation and then cycle with an 83% reversible volume expansion. Despite their massive expansion, the nanowires can be cycled without any cracking or facture during the ultrafast sodiation/desodiation process. Additionally, most of the phases involved in the sodiation/desodiation process possess high electrical conductivity. More specifically, the NaZnSb exhibits a layered structure, which provides channels for fast Na + diffusion. This observation indicates that Zn-Sb intermetallic nanomaterials offer great promise as high rate and good cycling stability anodic materials for the next generation of sodium-ion batteries.« less

Facile method for preparing organic/inorganic hybrid capsules using amino-functional silane coupling agent in aqueous media.

PubMed

Kurayama, Fumio; Suzuki, Satoru; Oyamada, Tetsuro; Furusawa, Takeshi; Sato, Masahide; Suzuki, Noboru

2010-09-01

A new and facile method for preparing microcapsules with 3-aminopropyltriethoxysilane (APTES)/alginate hybrid shell (AP-capsule) is proposed based on gelling and sol-gel processes. In this method, conventional capsules with alginate shells (Alg-capsule) are produced by dripping carboxymethyl cellulose solution containing calcium chloride into a sodium alginate solution. Subsequently, addition of the Alg-capsules to an aqueous APTES solution induces the formation of APTES/alginate hybrid shells. The optical observation shows that the texture of AP-capsules is more glossy and transparent than that of Alg-capsules. The surface morphology and elemental composition of microcapsules were characterized by Scanning Electron Microscopy (SEM), Fourier Transform Infrared Spectroscopy (FT-IR) and X-ray Photoelectron Spectroscopy (XPS). The results suggest that APTES molecules are incorporated to the framework of the alginate shells via electrostatic interaction between amino groups of APTES and carboxyl groups of alginate and the hybrid shells have a dense and homogeneous structure. In the formation reaction, the shrinking of the capsule shells occurs and the accumulation of APTES in the capsule shells proceeds with pseudo first-order kinetics. Moreover, these behaviors are greatly influenced by pH of the reaction solution, especially promoted under acidic and alkaline conditions. Copyright 2010 Elsevier Inc. All rights reserved.

Disinfection Pilot Trial for Little Miami WWTP | Science ...

EPA Pesticide Factsheets

There is a serious interest growing nationally towards the use of PAA at various stages of public waste water treatment facilities; one of such use is secondary waste water treatment. MSDGC is currently interested in improving efficiency and economic aspects of waste water treatment. MSDGC requested for ORD’s support to evaluate alternative cost-effective disinfectants. This report herein is based on the data generated from the field pilot test conducted at the Little Miami Wastewater Treatment Plant. Chlorine assisted disinfection of wastewaters created the concern regarding the formation of high levels of toxic halogenated disinfection byproducts (DBPs) detrimental to aquatic life and public health. Peracetic acid is emerging as a green alternative to chlorine and claimed to have economic and social benefits. In addition, it is a relatively simple retrofit to the existing chlorine treated wastewater treatment facilities. PAA is appealed to possess a much lower aquatic toxicity profile than chlorine and decays rapidly in the environment, even if overdosed. As a result, PAA generally does not need a quenching step, such as dechlorination, reducing process complexity, sodium pollution and cost. PAA treatment does not result in the formation of chlorinated disinfection by-products such as trihalomethanes (THMs), haloacetic acids and other byproducts such as cyanide and n-Nitrosodimethylamine (NDMA).

Facile fabrication of bowl-shaped microparticles for oral curcumin delivery to ulcerative colitis tissue.

PubMed

Chen, Qiubing; Gou, Shuangquan; Huang, Yamei; Zhou, Xin; Li, Qian; Han, Moon Kwon; Kang, Yuejun; Xiao, Bo

2018-05-05

Oral microparticles (MPs) have been considered as promising drug carriers in the treatment of ulcerative colitis (UC). Here, a facile strategy based on a conventional emulsion-solvent evaporation technique was used to fabricate bowl-shaped MPs (BMPs), and these MPs loaded with anti-inflammatory drug (curcumin, CUR) during the fabrication process. The physicochemical properties of the resultant BMPs were characterized by dynamic light scattering, scanning electron microscope, confocal laser scanning microscope and X-ray diffraction as well as contact angle goniometer. Results indicated that BMPs had a desirable hydrodynamic diameter (1.84 ± 0.20 μm), a negative zeta potential (-26.5 ± 1.13 mV), smooth surface morphology, high CUR encapsulation efficiency and controlled drug release profile. It was found that CUR molecules were dispersed in an amorphous state within the polymeric matrixes. In addition, BMPs showed excellent hydrophilicity due to the presence of Pluronic F127 and poly(vinyl alcohol) on their surface. More importantly, orally administered BMPs could efficiently alleviate UC based on a dextran sulfate sodium-induced mouse model. These results collectively suggest that BMP can be exploited as a readily scalable oral drug delivery system for UC therapy. Copyright © 2018 Elsevier B.V. All rights reserved.

The correlation of sodium and potassium metabolism with the level of energy consumption in man during adaptation to heat

NASA Technical Reports Server (NTRS)

Afanasyev, B. G.; Zhestovskiy, V. A.

1978-01-01

The sodium and potassium metabolism was studied in a thermal chamber at 35 deg and 80 percent relative humidity in 8 men for a period of 6 days. The control group (3 subjects) were outside of the chamber at a comfortable ambient temperature. The intracellular sodium and potassium metabolism were assessed based on their content in the erythrocytes. The finding was that during adaptation to heat, a considerable amount of sodium was excreted by the body in the sweat and urine (about 1/3 of the sodium content of the human body) as compared with its intake and the amount of potassium retained in the body. Changes in the concentration of sodium and potassium may serve as indexes of the state of adaptation processes during constant exposure to heat.

Sodium 3D COncentration MApping (COMA 3D) using 23Na and proton MRI

NASA Astrophysics Data System (ADS)

Truong, Milton L.; Harrington, Michael G.; Schepkin, Victor D.; Chekmenev, Eduard Y.

2014-10-01

Functional changes of sodium 3D MRI signals were converted into millimolar concentration changes using an open-source fully automated MATLAB toolbox. These concentration changes are visualized via 3D sodium concentration maps, and they are overlaid over conventional 3D proton images to provide high-resolution co-registration for easy correlation of functional changes to anatomical regions. Nearly 5000/h concentration maps were generated on a personal computer (ca. 2012) using 21.1 T 3D sodium MRI brain images of live rats with spatial resolution of 0.8 × 0.8 × 0.8 mm3 and imaging matrices of 60 × 60 × 60. The produced concentration maps allowed for non-invasive quantitative measurement of in vivo sodium concentration in the normal rat brain as a functional response to migraine-like conditions. The presented work can also be applied to sodium-associated changes in migraine, cancer, and other metabolic abnormalities that can be sensed by molecular imaging. The MATLAB toolbox allows for automated image analysis of the 3D images acquired on the Bruker platform and can be extended to other imaging platforms. The resulting images are presented in a form of series of 2D slices in all three dimensions in native MATLAB and PDF formats. The following is provided: (a) MATLAB source code for image processing, (b) the detailed processing procedures, (c) description of the code and all sub-routines, (d) example data sets of initial and processed data. The toolbox can be downloaded at: http://www.vuiis.vanderbilt.edu/ truongm/COMA3D/.

A facile approach towards synthesis, characterization, single crystal structure, and DFT study of 5-bromosalicylalcohol

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rastogi, Rupali, E-mail: rastogirupali@ymail.com; Tarannum, Nazia; Butcher, R. J.

2016-03-15

5-Bromosalicylalcohol was prepared by the interaction of NaBH{sub 4} and 5-bromosalicylaldehyde. The use of sodium borohydride makes the reaction easy, facile, economic and does not require any toxic catalyst. The compound is characterized by FTIR, {sup 1}H NMR, {sup 13}C NMR, TEM and ESI-mass spectra. Crystal structure is determined by single crystal X-ray analysis. Quantum mechanical calculations of geometries, energies and thermodynamic parameters are carried out using density functional theory (DFT/B3LYP) method with 6-311G(d,p) basis set. The optimized geometrical parameters obtained by B3LYP method show good agreement with experimental data.

Sodium azide

Integrated Risk Information System (IRIS)

Sodium azide ; CASRN 26628 - 22 - 8 Human health assessment information on a chemical substance is included in the IRIS database only after a comprehensive review of toxicity data , as outlined in the IRIS assessment development process . Sections I ( Health Hazard Assessments for Noncarcinogenic Ef

Dalapon, sodium salt

Integrated Risk Information System (IRIS)

Dalapon , sodium salt ; CASRN 75 - 99 - 0 Human health assessment information on a chemical substance is included in the IRIS database only after a comprehensive review of toxicity data , as outlined in the IRIS assessment development process . Sections I ( Health Hazard Assessments for Noncarcinoge

Chlorite (sodium salt)

Integrated Risk Information System (IRIS)

Chlorite ( sodium salt ) ; CASRN 7758 - 19 - 2 Human health assessment information on a chemical substance is included in the IRIS database only after a comprehensive review of toxicity data , as outlined in the IRIS assessment development process . Sections I ( Health Hazard Assessments for Noncarc

Low cost solar array project silicon materials task. Development of a process for high capacity arc heater production of silicon for solar arrays

NASA Technical Reports Server (NTRS)

Reed, W. H.

1978-01-01

Silicon tetrachloride and a reductant (sodium) will be injected into an arc heated mixture of hydrogen and argon, yielding silicon and gaseous sodium chloride. Detailed characterization of the Sonicore sodium injection nozzle, using water as the test fluid was completed. Results indicated that flow rates of 45 gph sodium and 50 scfm argon should produce sufficiently small droplet sizes. The design effort was also completed for the test system preparation which was divided into two categories: (1) system components and (2) test system-laboratory integration.

Superimpose signal processing method for micro-scale thermal imaging of solar salts at high temperature

NASA Astrophysics Data System (ADS)

Morikawa, Junko; Zamengo, Massimiliano; Kato, Yukitaka

2016-05-01

The global interest in energy applications activates the advanced study about the molten salts in the usage of fluids in the power cycle, such as for transport and heat storage in solar power facilities. However, the basic properties of molten salts show a general scattering in characterization especially in thermal properties. It is suggested that new studies are required on the measurement of thermal properties of solar salts using recent technologies. In this study, micro-scale heat transfer and phase change in molten salts are presented using our originally developed device: the micro-bolometer Infrared focal plane arrays (IR FPA) measuring system is a portable type instrument, which is re-designed to measure the thermal phenomena in high temperature up to 700 °C or higher. The superimpose system is newly setup adjusted to the signal processing in high temperature to realize the quantitative thermal imaging, simultaneously. The portable type apparatus for a quantitative micro-scale thermography using a micro-bolometer has been proposed based on an achromatic lens design to capture a micro-scale image in the long-wave infrared, a video signal superimposing for the real time emissivity correction, and a pseudo acceleration of a timeframe. Combined with the superimpose technique, the micro-scale thermal imaging in high temperature is achieved and the molten flows of the solar salts, sodium nitrate, and potassium nitrate are successfully observed. The solar salt, the mixture of sodium nitrate and potassium nitrate, shows a different shape of exothermic heat front morphology in the lower phase transition (solidification) temperature than the nitrates on cooling. The proposed measuring technique will be utilized to accelerate the screening step to determine the phase diagram and the eutectics of the multiple mixtures of candidate molten salts, which may be used as heat transport medium from the concentrated solar power to a processing plant for thermal energy storage.

Drowning-out crystallisation of sodium sulphate using aqueous two-phase systems.

PubMed

Taboada, M E; Graber, T A; Asenjo, J A; Andrews, B A

2000-06-23

A novel method to obtain crystals of pure, anhydrous salt, using aqueous two-phase systems was studied. A concentrated salt solution is mixed with polyethylene glycol (PEG), upon which three phases are formed: salt crystals, a PEG-rich liquid and a salt-rich liquid. After removal of the solid salt, a two-phase system is obtained. Both liquid phases are recycled, allowing the design of a continuous process, which could be exploited industrially. The phase diagram of the system water-Na2SO4-PEG 3350 at 28 degrees C was used. Several process alternatives are proposed and their economic potential is discussed. The process steps needed to produce sodium sulphate crystals include mixing, crystallisation, settling and, optionally, evaporation of water. The yield of sodium sulphate increases dramatically if an evaporation step is used.

Preparation of titanium phosphates with additives in hydrothermal process and their powder properties for cosmetics.

PubMed

Onoda, Hiroaki; Yamaguchi, Taisuke

2013-04-01

In this study, titanium phosphates were prepared from titanium chloride and phosphoric acid, sodium pyrophosphate and sodium triphosphate solutions with water retention compounds in hydrothermal process as a novel white pigment for cosmetics. Their chemical composition, powder properties, photo catalytic activity, water retention and smoothness were studied. The addition of glycerin in the preparation from sodium pyrophosphate has the useful method to obtain homogenized spherical particles of titanium phosphate pigments for the cosmetics. These titanium phosphates had less photo catalytic activity to protect the sebum on the skin. © 2012 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

Methylated liquor treatment process in caffeine production

NASA Astrophysics Data System (ADS)

Zhou, Junbo; Yang, Mingyang; Huang, Wenjia; Cui, Shenglu; Gao, Liping

2018-02-01

The caffeine production process produces a large amount of sodium methyl sulphate in the methylated mother liquor. In order to recycle this part of ingredient, we use the mother liquid of Shijiazhuang Xin Nuowei Pharmaceutical Co., Ltd. as the object of study, the use of “nanofiltration (NF) - Dish Type Reverse Osmosis (DTRO) “combination of membrane technology for desalination and concentration. The experimental results show that the concentration of sodium sulfate in the nanofiltration solution is 0.37 g • L -1, the rejection rate is 98%, and the concentration of sodium methyl sulfate in DTRO concentrated solution is 453.80 g • L -1, which meets the requirements of the enterprise.

Robust diamond-like Fe-Si network in the zero-strain Na xFeSiO 4 cathode

DOE PAGES

Ye, Zhuo; Zhao, Xin; Li, Shouding; ...

2016-07-14

Sodium orthosilicates Na 2 MSiO 4 ( M denotes transition metals) have attracted much attention due to the possibility of exchanging two electrons per formula unit. In this work, we report a group of sodium iron orthosilicates Na 2FeSiO 4. Their crystal structures are characterized by a diamond-like Fe-Si network. The Fe-Si network is quite robust against the charge/discharge process, which explains the high structural stability observed in experiment. Furthermore, using the density functional theory within the GGA + U framework and X-ray diffraction studies, the crystal structures and structural stabilities during the sodium extraction/re-insertion process are systematically investigated.

Process for production desulfurized of synthesis gas

DOEpatents

Wolfenbarger, James K.; Najjar, Mitri S.

1993-01-01

A process for the partial oxidation of a sulfur- and silicate-containing carbonaceous fuel to produce a synthesis gas with reduced sulfur content which comprises partially oxidizing said fuel at a temperature in the range of 1900.degree.-2600.degree. F. in the presence of a temperature moderator, an oxygen-containing gas and a sulfur capture additive which comprises a calcium-containing compound portion, a sodium-containing compound portion, and a fluoride-containing compound portion to produce a synthesis gas comprising H.sub.2 and CO with a reduced sulfur content and a molten slag which comprises (1) a sulfur-containing sodium-calcium-fluoride silicate phase; and (2) a sodium-calcium sulfide phase.

Know Your Noodles! Assessing Variations in Sodium Content of Instant Noodles across Countries.

PubMed

Farrand, Clare; Charlton, Karen; Crino, Michelle; Santos, Joseph; Rodriguez-Fernandez, Rodrigo; Ni Mhurchu, Cliona; Webster, Jacqui

2017-06-16

Reducing salt intake is a cost-effective public health intervention to reduce the global burden of non-communicable disease (NCDs). Ultra-processed foods contribute ~80% of dietary salt in high income countries, and are becoming prominent in low-middle income countries. Instant noodle consumption is particularly high in the Asia Pacific region. The aim of this study was to compare the sodium content of instant noodles sold worldwide to identify potential for reformulation. Analysis was undertaken for 765 instant noodle products from 10 countries using packaged food composition databases of ultra-processed foods compiled by the Global Food Monitoring Group (GFMG) and national shop survey data. Sodium levels were high and variable, within and between countries. Instant noodles in China had the highest mean sodium content (1944 mg/100 g; range: 397-3678/100 g) compared to New Zealand (798 mg/100 g; range: 249-2380 mg/100 g). Average pack size ranged from 57 g (Costa Rica) to 98 g (China). The average packet contributed 35% to 95% of the World Health Organization recommended daily salt intake of <5 g. Forty-one percent of products met the Pacific Island (PICs) regional sodium targets, 37% met the South Africa 2016 targets, and 62% met the UK 2017 targets. This study emphasises a need for stronger regulation and closer monitoring to drive rigorous reformulation of salt in ultra-processed foods.

Know Your Noodles! Assessing Variations in Sodium Content of Instant Noodles across Countries

PubMed Central

Farrand, Clare; Charlton, Karen; Crino, Michelle; Santos, Joseph; Rodriguez-Fernandez, Rodrigo; Ni Mhurchu, Cliona; Webster, Jacqui

2017-01-01

Reducing salt intake is a cost-effective public health intervention to reduce the global burden of non-communicable disease (NCDs). Ultra-processed foods contribute ~80% of dietary salt in high income countries, and are becoming prominent in low-middle income countries. Instant noodle consumption is particularly high in the Asia Pacific region. The aim of this study was to compare the sodium content of instant noodles sold worldwide to identify potential for reformulation. Analysis was undertaken for 765 instant noodle products from 10 countries using packaged food composition databases of ultra-processed foods compiled by the Global Food Monitoring Group (GFMG) and national shop survey data. Sodium levels were high and variable, within and between countries. Instant noodles in China had the highest mean sodium content (1944 mg/100 g; range: 397–3678/100 g) compared to New Zealand (798 mg/100 g; range: 249–2380 mg/100 g). Average pack size ranged from 57 g (Costa Rica) to 98 g (China). The average packet contributed 35% to 95% of the World Health Organization recommended daily salt intake of <5 g. Forty-one percent of products met the Pacific Island (PICs) regional sodium targets, 37% met the South Africa 2016 targets, and 62% met the UK 2017 targets. This study emphasises a need for stronger regulation and closer monitoring to drive rigorous reformulation of salt in ultra-processed foods. PMID:28621720

The Concept about the Regeneration of Spent Borohydrides and Used Catalysts from Green Electricity

PubMed Central

Liu, Cheng-Hong; Chen, Bing-Hung

2015-01-01

Currently, the Brown-Schlesinger process is still regarded as the most common and mature method for the commercial production of sodium borohydride (NaBH4). However, the metallic sodium, currently produced from the electrolysis of molten NaCl that is mass-produced by evaporation of seawater or brine, is probably the most costly raw material. Recently, several reports have demonstrated the feasibility of utilizing green electricity such as offshore wind power to produce metallic sodium through electrolysis of seawater. Based on this concept, we have made improvements and modified our previously proposed life cycle of sodium borohydride (NaBH4) and ammonia borane (NH3BH3), in order to further reduce costs in the conventional Brown-Schlesinger process. In summary, the revision in the concept combining the regeneration of the spent borohydrides and the used catalysts with the green electricity is reflected in (1) that metallic sodium could be produced from NaCl of high purity obtained from the conversion of the byproduct in the synthesis of NH3BH3 to devoid the complicated purification procedures if produced from seawater; and (2) that the recycling and the regeneration processes of the spent NaBH4 and NH3BH3 as well as the used catalysts could be simultaneously carried out and combined with the proposed life cycle of borohydrides.

Facile and efficient room temperature solid state reaction enabled synthesis of antimony nanoparticles embedded within reduced graphene oxide for enhanced sodium-ion storage

NASA Astrophysics Data System (ADS)

Zhang, Xiukui; Wu, Ping; Jiang, Li; Zhang, Xiaofang; Shi, Hongxia; Zhu, Xiaoshu; Wei, Shaohua; Zhou, Yiming

2018-06-01

Herein, a very simple and cost-effective solid state reaction method is employed to obtain, for the first time, the antimony nanoparticles embedded within reduced graphene oxide matrices (designated as Sb/rGO). By directly grinding antimony chloride and sodium hydroxide together at room temperature in the presence of graphene oxide (GO), Sb4O5Cl2 precursor was quickly obtained, which is evenly incorporated in the graphene oxide matrices. After subsequent chemical reduction by NaBH4, the Sb/rGO composite was successfully synthesized. The as-prepared Sb/rGO composite consists of uniform Sb nanoparticles of sub-20 nm, all of which have been wrapped in and protected by the rGO matrices. The Sb nanoparticles serve as a sufficient sodium ion reservoir while the rGO matrices provide highly efficient pathways for transport of sodium ions and electrons. Moreover, the volume expansion of Sb during sodiation can be buffered in the rGO matrices. As a result, the Sb/rGO composite exhibits excellent electrochemical performance in sodium-ion batteries (SIBs), including an enhanced cycling stability with a highly reversible charge capacity of 455 mA h g-1 after 45 cycles at 100 mA g-1, and a coulombic efficiency exceeding 98% during cycling. The findings in the present work pave the way to not only synthesize the designated promising electrode materials for high performance SIBs, but also thoroughly understand the solid-state reaction.

Variation of Lunar Sodium During Passage of the Moon through the Earth's Magnetotail

NASA Technical Reports Server (NTRS)

Potter, Andrew E.; Killen, Rosemary M.; Morgan, Thomas H.

2000-01-01

We measured sodium emission above the lunar equator over a range of lunar altitudes from 100 to 4000 km. The measurements were repeated approximately every 24 hours from June 7 to 16, 1998, covering the period during which the Moon passed through the Earth's magnetotail. Sodium temperatures derived from the altitude dependence of emission intensity ranged from 1200 to 2900 K. This result supports the view that photodesorption is a primary source of sodium in the exosphere since the most probable temperature of sodium form this source is in this range. Passage of the Moon through the Earth's magnetotail (where solar wind is essentially absent) affected the sodium density, such that it was higher before the Moon entered the Earth's magnetotail than after the Moon left it. This suggests that the solar wind plays a role in production of lunar sodium. We propose that its function is to mobilize sodium and bring it to the surface, where photodesorption can eject it into the exosphere. A two-step process such as this could help to explain the latitude dependence of sodium density, which varies as the second or higher power of cosine latitude.

A hydrometallurgical process for recovering total metal values from waste monolithic ceramic capacitors.

PubMed

Prabaharan, G; Barik, S P; Kumar, B

2016-06-01

A hydrometallurgical process for recovering the total metal values from waste monolithic ceramic capacitors was investigated. The process parameters such as time, temperature, acid concentration, hydrogen peroxide concentration and other reagents (amount of zinc dust and sodium formate) were optimized. Base metals such as Ba, Ti, Sn, Cu and Ni are leached out in two stages using HCl in stage 1 and HCl with H2O2 in stage 2. More than 99% of leaching efficiency for base metals (Cu, Ni, Ba, Ti and Sn) was achieved. Precious metals such as Au and Pd are leached out using aquaregia and nitric acid was used for the leaching of Ag. Base metals (Ba, Ti, Sn, Cu and Ni) are recovered by selective precipitation using H2SO4 and NaOH solution. In case of precious metals, Au and Pd from the leach solution were precipitated out using sodium metabisulphite and sodium formate, respectively. Sodium chloride was used for the precipitation of Ag from leach solution. Overall recovery for base metals and precious metals are 95% and 92%, respectively. Based on the results of the present study, a process flow diagram was proposed for commercial application. Copyright © 2016 Elsevier Ltd. All rights reserved.

Separation of Lead from Crude Antimony by Pyro-Refining Process with NaPO3 Addition

NASA Astrophysics Data System (ADS)

Ye, Longgang; Hu, Yuejie; Xia, Zhimei; Chen, Yongming

2016-06-01

The main purpose of this study was to separate lead from crude antimony through an oxidation pyro-refining process and by using sodium metaphosphate as a lead elimination reagent. The process parameters that will affect the refining results were optimized experimentally under controlled conditions, such as the sodium metaphosphate charging dosage, the refining temperature and duration, and the air flow rate, to determine their effect on the lead content in refined antimony and the lead removal rate. A minimum lead content of 0.0522 wt.% and a 98.6% lead removal rate were obtained under the following optimal conditions: W_{{{NaPO}_{{3}} }} = 15% W Sb (where W represents weight), a refining temperature of 800°C, a refining time of 30 min, and an air flow rate of 3 L/min. X-ray diffractometry and scanning electron microscopy showed that high-purity antimony was obtained. The smelting operation is free from smoke or ammonia pollution when using monobasic sodium phosphate or ammonium dihydrogen phosphate as the lead elimination reagent. However, this refining process can also remove a certain amount of sulfur, cobalt, and silicon simultaneously, and smelting results also suggest that sodium metaphosphate can be used as a potential lead elimination reagent for bismuth and copper refining.

Applicability of salt reduction strategies in pizza crust.

PubMed

Mueller, Eva; Koehler, Peter; Scherf, Katharina Anne

2016-02-01

In an effort to reduce population-wide sodium intake from processed foods, due to major health concerns, several different strategies for sodium reduction in pizza crust without any topping were evaluated by sensory analyses. It was possible to reduce sodium by 10% in one single step or to replace 30% of NaCl by KCl without a noticeable loss of salty taste. The late addition of coarse-grained NaCl (crystal size: 0.4-1.4 mm) to pizza dough led to an enhancement of saltiness through taste contrast and an accelerated sodium delivery measured in the mouth and in a model mastication simulator. Likewise, the application of an aqueous salt solution to one side of the pizza crust led to an enhancement of saltiness perception through faster sodium availability, leading to a greater contrast in sodium concentration. Each of these two strategies allowed a sodium reduction of up to 25% while maintaining taste quality. Copyright © 2015 Elsevier Ltd. All rights reserved.

[Effect of nitric oxide on the somatic membrane of rat DRG neurons].

PubMed

Cheng, Hong-Ju; Ma, Ke-Tao; Zhao, Lei; Li, Li; Cao, Ying-Ying; Si, Jun-Qiang

2009-11-01

To observe the role of nitric oxide in dorsal root ganglion (DRG) neurons and its related ionic mechanisms, and explore the function of NO in pain transmission process. In freshly isolated rat DRG samples, using intracellular recording technique, we perfused sodium nitroprusside (NO donor) to observe the role of NO in DRG neurons. In 77.45% of the bath cells, application of sodium nitroprusside (10 -100 mmol/L) induced concentration-dependent membrane hyperpolarization (79/102), and remaining neurons had no response. The membrane conductance increased from control value of (21.06 +/- 1.94) nS to (23.08 +/- 0.92) nS during sodium nitroprusside induced hyperpolarization. L-NAME (1 mmol/L), CdCl2 (0.1 mmol/L) and non-sodium BSS failed to change the amplitude of sodium nitroprusside induced hyperpolarization. When BSS containing 10 mmol/L TEA was used, sodium nitroprusside induced hyperpolarization was obviously inhibited. Sodium nitroprusside could cause concentration-dependent hyperpolarization in DRG neurons by activating K+ channels.

Synthesis and characterization of carbon microsphere for extinguishing sodium fire

NASA Astrophysics Data System (ADS)

Snehalatha, V.; Ponraju, D.; Nashine, B. K.; Chellapandi, P.

2013-06-01

In Sodium cooled Fast breeder Reactors (SFRs), accidental leakage of liquid sodium leads to sodium fire. Carbon microsphere is a promising and novel extinguishant for sodium fire since it possesses high thermal conductivity, chemical inertness and excellent flow characteristics. Low density Carbon microsphere (CMS) with high thermal stability was successfully synthesized from functionalized styrene divinyl benzene copolymer by carbonization under inert atmosphere. Protocol for stepwise carbonization was developed by optimizing heating rate and time of heating. The synthesized CMS was characterized by Densimeter, Scanning Electron Microscope (SEM), Fourier Transfer Infra-Red spectroscopy (FTIR), Thermogravimetry (TG), X-ray Diffraction (XRD) and RAMAN spectroscopy. CMS thus obtained was spherical in shape having diameters ranging between 60 to 80μm with narrow size distribution. The smooth surface of CMS ensures its free flow characteristics. The yield of carbonization process was about 38%. The performance of CMS was tested on small scale sodium. This paper describes the development of carbon microsphere for extinguishing sodium fire and its characteristics.

Handbook: Approaches for the Remediation of Federal Facility Sites Contaminated with Explosive or Radioactive Wastes

DTIC Science & Technology

1993-09-01

ash, and incinerator fly ash in modified sulfur cement and Portland cement waste forms ................................. 70 6-10 Drawing of full-scale...6-17 Economic analysis of encapsulating sodium nitrate at Rocky Flats Plant ..................... 74 6-18 Portland cement and modified sulfur cement...environment. DP-1629. Savannah and modified sulfur cement encapsulation. Both methods River Laboratory, Aiken, South Carolina. have advantages over

In situ X-ray diffraction characterization of NiSe2 as a promising anode material for sodium ion batteries

NASA Astrophysics Data System (ADS)

Ou, Xing; Li, Jiao; Zheng, Fenghua; Wu, Peng; Pan, Qichang; Xiong, Xunhui; Yang, Chenghao; Liu, Meilin

2017-03-01

Reduced graphene oxide (rGO) homogenously wrapped nickel diselenide (NiSe2/rGO) hybrid has been prepared by a facile one-spot hydrothermal method. When investigated as anode material for sodium ion batteries (SIBs), NiSe2/rGO hybrid delivers a high reversible capacity (433 mAh g-1 at 100 mA g-1), superior rate performance (406, 386, 366, 347 and 318 mAh g-1 at 200, 500, 1000, 2000 and 5000 mA g-1, respectively) and excellent cycling stability (a capacity retention of 346 mAh g-1 after 1000 cycles at 1000 mA g-1) within the 0.4-3.0 V voltage range. In situ XRD analysis and ex situ SEM/TEM measurement reveal that the high capacity of NiSe2/rGO is originated from the combined Na+ intercalation and conversion reactions. These results validate the impact of voltage range on electrochemical property, providing a new route to rationalize the limiting factors that affect the performance of NiSe2 anode material. The facile synthesis and superior electrochemical performance of the NiSe2/rGO hybrid render it a promising anode material for SIBs.

Sodium citrate assisted facile synthesis of AuPd alloy networks for ethanol electrooxidation with high activity and durability

NASA Astrophysics Data System (ADS)

Zhai, Yanling; Zhu, Zhijun; Lu, Xiaolin; Zhou, H. Susan

2016-10-01

The direct ethanol fuel cell is an emerging energy conversion device for which palladium is considered as the one of the most effective components for anode catalyst, however, its widespread application has been still limited by the activity and durability of the anode catalyst. In this work, AuPd alloy networks (NWs) are synthesized using H2PdCl4 and HAuCl4 as precursors reduced by NaBH4 in the presence of sodium citrate (SC). The results reveal that SC plays significant role in network structure, resulting in the enhanced electrocatalytic activity of the catalyst. This self-supported AuPd NWs catalyst exhibits much higher electrochemical catalytic activity than commercial Pd/C catalyst toward ethanol electrooxidation in alkaline solution. Significantly, AuPd NWs catalyst shows extremely high durability at the beginning of the chronoamperometry test, and as high as 49% of the mass current density (1.41 A/mgPd) remains after 4000 s current-time test at -0.3 V (vs. Ag/AgCl) in N2-saturated KOH-ethanol solution. This strategy provides a facile method for the preparation of alloy networks with high electrochemical activity, and can be potentially expanded to a variety of electrochemical applications.

Limited sterile processing capabilities for safe surgery in low-income and middle-income countries: experience in the Republic of Congo, Madagascar and Benin.

PubMed

Fast, Olive; Fast, Christina; Fast, Dan; Veltjens, Suzanne; Salami, Zouliha; White, Michelle C

2017-01-01

It is highly difficult to perform safe surgery without sterile instruments, yet the capacity to adequately clean, disinfect and sterilise surgical instruments in low-income and middle-income countries is largely unknown. Sterile Processing Education Charitable Trust developed an assessment tool and, in partnership with Mercy Ships, evaluated the sterile processing capacity in 59 facilities in Madagascar, Benin and the Republic of Congo. This data-driven analysis paper illustrates how lack of sterile processing capacity acts as a barrier to safe surgical care. Our tool identified widespread lack of knowledge of techniques and resources needed for sterile processing. Only 12% of workers in Republic of Congo and Benin had sterile processing training and none in Madagascar. None of the hospitals surveyed met basic standards for cleaning, disinfection and sterilisation as defined by the WHO/Pan American Health Organization. Examples of poor practice included lack of cleaning supplies (basic brushes and detergents), incorrect drying and storage of surgical instruments, and inattention to workflow causing cross-contamination. Bleach (sodium hypochlorite) solutions, damaging to instruments, were used universally. In our experience, using an assessment tool allowed identification of specific gaps in sterile processing capacity. Many of the gaps are amenable to simple solutions requiring minimal resources and achievable by most hospitals. We recommend that stakeholders seeking to strengthen surgical health systems in low-resource settings incorporate sterile processing capacity assessments and training into their programmes.

Limited sterile processing capabilities for safe surgery in low-income and middle-income countries: experience in the Republic of Congo, Madagascar and Benin

PubMed Central

Fast, Olive; Fast, Christina; Fast, Dan; Veltjens, Suzanne; Salami, Zouliha

2017-01-01

It is highly difficult to perform safe surgery without sterile instruments, yet the capacity to adequately clean, disinfect and sterilise surgical instruments in low-income and middle-income countries is largely unknown. Sterile Processing Education Charitable Trust developed an assessment tool and, in partnership with Mercy Ships, evaluated the sterile processing capacity in 59 facilities in Madagascar, Benin and the Republic of Congo. This data-driven analysis paper illustrates how lack of sterile processing capacity acts as a barrier to safe surgical care. Our tool identified widespread lack of knowledge of techniques and resources needed for sterile processing. Only 12% of workers in Republic of Congo and Benin had sterile processing training and none in Madagascar. None of the hospitals surveyed met basic standards for cleaning, disinfection and sterilisation as defined by the WHO/Pan American Health Organization. Examples of poor practice included lack of cleaning supplies (basic brushes and detergents), incorrect drying and storage of surgical instruments, and inattention to workflow causing cross-contamination. Bleach (sodium hypochlorite) solutions, damaging to instruments, were used universally. In our experience, using an assessment tool allowed identification of specific gaps in sterile processing capacity. Many of the gaps are amenable to simple solutions requiring minimal resources and achievable by most hospitals. We recommend that stakeholders seeking to strengthen surgical health systems in low-resource settings incorporate sterile processing capacity assessments and training into their programmes. PMID:29225957

Chlor-Alkali Technology.

ERIC Educational Resources Information Center

Venkatesh, S.; Tilak, B. V.

1983-01-01

Chlor-alkali technology is one of the largest electrochemical industries in the world, the main products being chlorine and caustic soda (sodium hydroxide) generated simultaneously by the electrolysis of sodium chloride. This technology is reviewed in terms of electrochemical principles and manufacturing processes involved. (Author/JN)

Modeling time to inactivation of Listeria monocytogenes in response to high pressure, sodium chloride, and sodium lactate.

PubMed

Youart, Alyssa M; Huang, Yang; Stewart, Cynthia M; Kalinowski, Robin M; Legan, J David

2010-10-01

A mathematical model was developed to predict time to inactivation (TTI) by high pressure processing of Listeria monocytogenes in a broth system (pH 6.3) as a function of pressure (450 to 700 MPa), inoculum level (2 to 6 log CFU/ml), sodium chloride (1 or 2%), and sodium lactate (0 or 2.5%) from a 4°C initial temperature. Ten L. monocytogenes isolates from various sources, including processed meats, were evaluated for pressure resistance. The five most resistant strains were used as a cocktail to determine TTI and for model validation. Complete inactivation of L. monocytogenes in all treatments was demonstrated with an enrichment method. The TTI increased with increasing inoculum level and decreasing pressure magnitude, from 1.5 min at 700 MPa and 2 log CFU/ml, to 15 min at 450 MPa and 6 log CFU/ml. Neither NaCl nor sodium lactate significantly influenced TTI. The model was validated with ready-to-eat, uncured, Australian retail poultry products, and with product specially made at a U.S. Department of Agriculture, Food Safety and Inspection Service (FSIS)-inspected pilot plant in the United States. Data from the 210 individual product samples used for validation indicate that the model gives "fail-safe" predictions (58% with response as expected, 39% with no survivors where survivors expected, and only 3% with survivors where none were expected). This model can help manufacturers of refrigerated ready-to-eat meats establish effective processing criteria for the use of high pressure processing as a postlethality treatment for L. monocytogenes in accordance with FSIS regulations.

Adoptable Interventions, Human Health, and Food Safety Considerations for Reducing Sodium Content of Processed Food Products

PubMed Central

Allison, Abimbola; Fouladkhah, Aliyar

2018-01-01

Although vital for maintaining health when consumed in moderation, various epidemiological studies in recent years have shown a strong association between excess dietary sodium with an array of health complications. These associations are robust and clinically significant for development of hypertension and prehypertension, two of the leading causes of preventable mortality worldwide, in adults with a high-sodium diet. Data from developed nations and transition economies show worldwide sodium intake of higher than recommended amounts in various nations. While natural foods typically contain a moderate amount of sodium, manufactured food products are the main contributor to dietary sodium intake, up to 75% of sodium in diet of American adults, as an example. Lower cost in formulation, positive effects on organoleptic properties of food products, effects on food quality during shelf-life, and microbiological food safety, make sodium chloride a notable candidate and an indispensable part of formulation of various products. Although low-sodium formulation of each product possesses a unique set of challenges, review of literature shows an abundance of successful experiences for products of many categories. The current study discusses adoptable interventions for product development and reformulation of products to achieve a modest amount of final sodium content while maintaining taste, quality, shelf-stability, and microbiological food safety. PMID:29389843

Adoptable Interventions, Human Health, and Food Safety Considerations for Reducing Sodium Content of Processed Food Products.

PubMed

Allison, Abimbola; Fouladkhah, Aliyar

2018-02-01

Although vital for maintaining health when consumed in moderation, various epidemiological studies in recent years have shown a strong association between excess dietary sodium with an array of health complications. These associations are robust and clinically significant for development of hypertension and prehypertension, two of the leading causes of preventable mortality worldwide, in adults with a high-sodium diet. Data from developed nations and transition economies show worldwide sodium intake of higher than recommended amounts in various nations. While natural foods typically contain a moderate amount of sodium, manufactured food products are the main contributor to dietary sodium intake, up to 75% of sodium in diet of American adults, as an example. Lower cost in formulation, positive effects on organoleptic properties of food products, effects on food quality during shelf-life, and microbiological food safety, make sodium chloride a notable candidate and an indispensable part of formulation of various products. Although low-sodium formulation of each product possesses a unique set of challenges, review of literature shows an abundance of successful experiences for products of many categories. The current study discusses adoptable interventions for product development and reformulation of products to achieve a modest amount of final sodium content while maintaining taste, quality, shelf-stability, and microbiological food safety.

Chitosan-Sodium Phytate Films with a Strong Water Barrier and Antimicrobial Properties Produced via One-Step-Consecutive-Stripping and Layer-by-Layer-Casting Technologies.

PubMed

Yang, Jie; Xiong, Liu; Li, Man; Sun, Qingjie

2018-06-20

The pursuit of sustainable functional materials requires the development of materials based on renewable resources and efficient fabrication methods. Here, we first fabricated chitosan-sodium phytate films via one-step-stripping and layer-by-layer-casting technologies. The proposed film-fabrication methods are general, facile, environmentally benign, cost-effective, and easy to scale up. The resultant one-step-stripped film was thin (9 ± 1 μm), soft, transparent, and strong, whereas the thickness of the layer-by-layer-cast film was 70 ± 3 μm. FTIR analysis of the films indicated the formation of interactions between the phosphoric groups in sodium phytate and the amino groups in chitosan. More importantly, the water-vapor-permeability values of the one-step-stripped and cast films were 4-5 orders of magnitude lower than chitosan films reported before. Layer-by-layer-cast films in particular exhibited high tensile strength (49.21 ± 1.12 MPa) and were more than three times stronger than other polyelectrolyte multilayer films. Both types of films remained stable in an acidic environment. Furthermore, the layer-by-layer-assembled films presented greater antimicrobial activity than the stripped films. The developed chitosan-sodium phytate films can enhance several biomedical and environmental applications, such as packaging, drug delivery, diagnostics, microfluidics, and biosensing.

Production of sodium-22 from proton irradiated aluminum

DOEpatents

Taylor, Wayne A.; Heaton, Richard C.; Jamriska, David J.

1996-01-01

A process for selective separation of sodium-22 from a proton irradiated minum target including dissolving a proton irradiated aluminum target in hydrochloric acid to form a first solution including aluminum ions and sodium ions, separating a portion of the aluminum ions from the first solution by crystallization of an aluminum salt, contacting the remaining first solution with an anion exchange resin whereby ions selected from the group consisting of iron and copper are selectively absorbed by the anion exchange resin while aluminum ions and sodium ions remain in solution, contacting the solution with an cation exchange resin whereby aluminum ions and sodium ions are adsorbed by the cation exchange resin, and, contacting the cation exchange resin with an acid solution capable of selectively separating the adsorbed sodium ions from the cation exchange resin while aluminum ions remain adsorbed on the cation exchange resin is disclosed.

Interpretation of postmortem vitreous concentrations of sodium and chloride.

PubMed

Zilg, B; Alkass, K; Berg, S; Druid, H

2016-06-01

Vitreous fluid can be used to analyze sodium and chloride levels in deceased persons, but it remains unclear to what extent such results can be used to diagnose antemortem sodium or chloride imbalances. In this study we present vitreous sodium and chloride levels from more than 3000 cases. We show that vitreous sodium and chloride levels both decrease with approximately 2.2mmol/L per day after death. Since potassium is a well-established marker for postmortem interval (PMI) and easily can be analyzed along with sodium and chloride, we have correlated sodium and chloride levels with the potassium levels and present postmortem reference ranges relative the potassium levels. We found that virtually all cases outside the reference range show signs of antemortem hypo- or hypernatremia. Vitreous sodium or chloride levels can be the only means to diagnose cases of water or salt intoxication, beer potomania or dehydration. We further show that postmortem vitreous sodium and chloride strongly correlate and in practice can be used interchangeably if analysis of one of the ions fails. It has been suggested that vitreous sodium and chloride levels can be used to diagnose drowning or to distinguish saltwater from freshwater drowning. Our results show that in cases of freshwater drowning, vitreous sodium levels are decreased, but that this mainly is an effect of postmortem diffusion between the eye and surrounding water rather than due to the drowning process, since the decrease in sodium levels correlates with immersion time. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Pyroprocessing of oxidized sodium-bonded fast reactor fuel - An experimental study of treatment options for degraded EBR-II fuel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hermann, S.D.; Gese, N.J.; Wurth, L.A.

An experimental study was conducted to assess pyrochemical treatment options for degraded EBR-II fuel. As oxidized material, the degraded fuel would need to be converted back to metal to enable electrorefining within an existing electro-metallurgical treatment process. A lithium-based electrolytic reduction process was studied to assess the efficacy of converting oxide materials to metal with a particular focus on the impact of zirconium oxide and sodium oxide on this process. Bench-scale electrolytic reduction experiments were performed in LiCl-Li{sub 2}O at 650 C. degrees with combinations of manganese oxide (used as a surrogate for uranium oxide), zirconium oxide, and sodium oxide.more » In the absence of zirconium or sodium oxide, the electrolytic reduction of MnO showed nearly complete conversion to metal. The electrolytic reduction of a blend of MnO-ZrO{sub 2} in LiCl - 1 wt% Li{sub 2}O showed substantial reduction of manganese, but only 8.5% of the zirconium was found in the metal phase. The electrolytic reduction of the same blend of MnO-ZrO{sub 2} in LiCl - 1 wt% Li{sub 2}O - 6.2 wt% Na{sub 2}O showed substantial reduction of manganese, but zirconium reduction was even less at 2.4%. This study concluded that ZrO{sub 2} cannot be substantially reduced to metal in an electrolytic reduction system with LiCl - 1 wt% Li{sub 2}O at 650 C. degrees due to the perceived preferential formation of lithium zirconate. This study also identified a possible interference that sodium oxide may have on the same system by introducing a parasitic and cyclic reaction of dissolved sodium metal between oxidation at the anode and reduction at the cathode. When applied to oxidized sodium-bonded EBR-II fuel (e.g., U-10Zr), the prescribed electrolytic reduction system would not be expected to substantially reduce zirconium oxide, and the accumulation of sodium in the electrolyte could interfere with the reduction of uranium oxide, or at least render it less efficient.« less

Modify washing solutions in the process of deglycerolization in ACP 215 and storage at 4°C in 0.9% sodium chloride in 24h.

PubMed

Zhao, Yang; Luo, Guangping; Luo, Hong; Ye, Xin; Rong, Xia; Huang, Kejun

2010-10-01

The ACP 215 was a functional closed system for preparing glycerolized and deglycerolized RBCs, CSBT had approved the technique of long term storage glycerolized rare blood lower than -65°C, and then deglycerolized by this machine. From the manual method to use ACP 215, Chinese blood banks chose 9% sodium chloride and 0.9% sodium chloride in deglycerolization process, while the AABB guideline prescribed that 12% sodium chloride and 0.9% sodium chloride-0.2% glucose were acceptable in washing step of ACP 215. In addition, 0.9% sodium chloride was the only solution which was permitted by CSBT to be added into postwash RBCs, while in America many kinds of additive solutions like AS-3 could be added into postwash RBCs and stored at 4°C for 14 days. Changes of washing solutions and preservation solution were much different from the original procedure of ACP 215 approved by the FDA. It was necessary to assess the quality of deglyceroled and postwash RBCs by this modified process in ACP 215 in China. Two-unit whole bloods were collected from each volunteer and preserved in CP2D for anticoagulant. It was then centrifuged to separate the plasma, and suspending RBCs were stored at 4°C in MAP for 6 days. Each unit of RBC was transferred to a 1000-ml PVC plastic bag, an improved procedure including the single-disposable glycerolization set in an automated, functionally closed system (ACP 215, Haemonetics) was used to glycerolize RBC with 40% (wt/vol) glycerol, then frozen at -80°C. Two modified washing solutions of 9% sodium chloride and 0.9% sodium chloride were used to deglycerolize the same RBCs with single disposable deglycerolization set in ACP 215. The deglycerolized RBCs were stored at 4°C in 0.9% sodium chloride for 24h. The freeze-thaw recovery value was 95.3±1.8% (mean±SD); the freeze-thaw-wash recovery value was 82.3±5.94% (mean±SD); the residure glycerol was 6.1±1.66 mg/dl (mean±SD), storage at 4°C in 0.9% sodium chloride within 24h after deglycerolization the supernatant Hb was 43±12 mg/dl (mean±SD); the hemolysis rate was 0.2±0.1% (mean±SD); the supernatant potassium level was 4.03±0.81 mM (mean±SD); and the postwash units were negative for both aerobic and anaerobic bacteria. The postwash of deglycerolized RBC had an acceptable FTW recovery value, and stored in 0.9% sodium chloride for 24h at 4°C, had an acceptable hemolysis. Modified washing solutions of 9% sodium chloride and 0.9% sodium chloride and without any of preservation had not affected the quality of frozen RBCs prepared in ACP 215 and postwash stored at 4°C in 0.9% sodium chloride within 24h. Copyright © 2010 Elsevier Ltd. All rights reserved.

High frequency noise measurements during CNEN/NIRA steam generator testing at Les Renardieres

NASA Astrophysics Data System (ADS)

Clapis, A.; Scandolo, D.; Regis, V.; Rappini, R.

The most significant results of the acoustic measurements carried out on the PGV-1 sodium-steam generator during the test of the 50 MW prototype on the CGVS loop facility are described. The prototype test was done in the isothermal condition, i.e., without steam production and in the power condition. During the first phase tests were made with low pressure hydrogen injection in sodium. The main purpose of the acoustic measurements, limited to the 100 to 1000 kHz frequency range, was to evaluate the noise characteristics (level and power spectrum) in all working states of the plant. A small leak of gas found in the isothermal condition enabled the sensitivity of the acoustic leak detection technique to be evaluated qualitatively. The results in form of spectral analysis charts are included.

Assembly and Thermal Hydraulic Test of a Stainless Steel Sodium-Potassium Circuit

NASA Technical Reports Server (NTRS)

Garber, A.; Godfroy, T.; Webster, K.

2007-01-01

Early Flight Fission Test Facilities (EFF-TF) team has been tasked by the NASA Marshall Space Flight Center Nuclear Systems Office to design, fabricate, and test an actively pumped alkali metal flow circuit. The system was originally built for use with lithium, but due to a shift in focus, it was redesigned for use with a eutectic mixture of sodium potassium (NaK). Basic circuit components include: reactor segment, NaK to gas heat exchanger, electromagnetic (EM) liquid metal pump, load/drain reservoir, expansion reservoir, instrumentation, and a spill reservoir. A 37-pin partial-array core (pin and flow path dimensions are the same as those in a full design) was selected for fabrication and test. This paper summarizes the first fill and checkout testing of the Stainless Steel NaK-Cooled Circuit (SNaKC).

[Study of scavenging activity of sorghum pigment to hydroxyl free radicals by fluorimetry].

PubMed

Zhang, Hai-rong; Wang, Wen-yan

2007-03-01

A natural product, sorghum pigment, consists of a number of important flavonoid derivatives, occurrs on the seed capsules or in the stems of many sorghums, and is widely applied in different fields of food, cosmetic and dyeing industries, It is important for scavenging hydroxyl free radicals and protection of human healthiness. Scavenging capacities of hydroxyl free radicals with sodium nitrite, quercetin and sorghum pigment were comparatively researched by fluorimetry, and the model of hydroxyl free radicals produced is based on the reaction of Cu2+ -catalyzed oxidation of ascorbic acid in the presence of hydrogen peroxide. The hydroxyl radicals react with benzoic acid, forming a fluorescent product, and the fluorescence intensity was determined by the concentration of hydroxybenzoic acid. The experimental results show that the sodium nitrite, quercetin and sorghum pigment have a quantity-effect relationship for scavenging hydroxyl free radicals, and sodium nitrite and quercetin in comparison with sorghum pigment have high antioxidant capacity. Finally, the quenching mechanisms were explored with sodium nitrite, sorghum pigment, and quercetin respectively. The sorghum pigment and sodium nitrite feature a dynamic quenching processes, while quercetin shows a static quenching processes. A reference method was provided for reasonable exploitation and utilization of sorghum pigment.

Facile synthesis of light harvesting semiconductor bismuth oxychloride nano photo-catalysts for efficient removal of hazardous organic pollutants

PubMed Central

Seddigi, Zaki S.; Baig, Umair; Ahmed, Saleh A.; Abdulaziz, M. A.; Danish, Ekram Y.; Khaled, Mazen M.; Lais, Abul

2017-01-01

In the present work, bismuth oxychloride nanoparticles–a light harvesting semiconductor photocatalyst–were synthesized by a facile hydrolysis route, with sodium bismuthate and hydroxylammonium chloride as the precursor materials. The as-synthesized semiconductor photocatalysts were characterized using X-ray diffraction analysis, Fourier transform infra-red spectroscopy, Raman spectroscopy, Field emission scanning electron microscopy, X-ray photoelectron spectroscopy and Photoluminescence spectroscopy techniques. The crystal structure, morphology, composition, and optical properties of these facile synthesized bismuth oxychloride nanoparticles (BiOCl NPs) were compared to those of traditional bismuth oxychloride. In addition, the photocatalytic performance of facile-synthesized BiOCl NPs and traditional BiOCl, as applied to the removal of hazardous organic dyes under visible light illumination, is thoroughly investigated. Our results reveal that facile-synthesized BiOCl NPs display strong UV-Vis light adsorption, improved charge carrier mobility and an inhibited rate of charge carrier recombination, when compared to traditional BiOCl. These enhancements result in an improved photocatalytic degradation rate of hazardous organic dyes under UV-Vis irradiance. For instance, the facile-synthesized BiOCl NPs attained 100% degradation of methylene blue and methyl orange dyes in approximately 30 mins under UV-Vis irradiation, against 55% degradation for traditional BiOCl under similar experimental conditions. PMID:28245225

Facile synthesis of light harvesting semiconductor bismuth oxychloride nano photo-catalysts for efficient removal of hazardous organic pollutants.

PubMed

Seddigi, Zaki S; Gondal, Mohammed A; Baig, Umair; Ahmed, Saleh A; Abdulaziz, M A; Danish, Ekram Y; Khaled, Mazen M; Lais, Abul

2017-01-01

In the present work, bismuth oxychloride nanoparticles-a light harvesting semiconductor photocatalyst-were synthesized by a facile hydrolysis route, with sodium bismuthate and hydroxylammonium chloride as the precursor materials. The as-synthesized semiconductor photocatalysts were characterized using X-ray diffraction analysis, Fourier transform infra-red spectroscopy, Raman spectroscopy, Field emission scanning electron microscopy, X-ray photoelectron spectroscopy and Photoluminescence spectroscopy techniques. The crystal structure, morphology, composition, and optical properties of these facile synthesized bismuth oxychloride nanoparticles (BiOCl NPs) were compared to those of traditional bismuth oxychloride. In addition, the photocatalytic performance of facile-synthesized BiOCl NPs and traditional BiOCl, as applied to the removal of hazardous organic dyes under visible light illumination, is thoroughly investigated. Our results reveal that facile-synthesized BiOCl NPs display strong UV-Vis light adsorption, improved charge carrier mobility and an inhibited rate of charge carrier recombination, when compared to traditional BiOCl. These enhancements result in an improved photocatalytic degradation rate of hazardous organic dyes under UV-Vis irradiance. For instance, the facile-synthesized BiOCl NPs attained 100% degradation of methylene blue and methyl orange dyes in approximately 30 mins under UV-Vis irradiation, against 55% degradation for traditional BiOCl under similar experimental conditions.

Scaling effects in sodium zirconium silicate phosphate (Na 1+ xZr 2Si xP 3- xO 12) ion-conducting thin films

DOE PAGES

Ihlefeld, Jon F.; Gurniak, Emily; Jones, Brad H.; ...

2016-05-04

Preparation of sodium zirconium silicate phosphate (NaSICon), Na 1+xZr 2Si xP 3–xO 12 (0.25 ≤ x ≤ 1.0), thin films has been investigated via a chemical solution approach on platinized silicon substrates. Increasing the silicon content resulted in a reduction in the crystallite size and a reduction in the measured ionic conductivity. Processing temperature was also found to affect microstructure and ionic conductivity with higher processing temperatures resulting in larger crystallite sizes and higher ionic conductivities. The highest room temperature sodium ion conductivity was measured for an x = 0.25 composition at 2.3 × 10 –5 S/cm. In conclusion, themore » decreasing ionic conductivity trends with increasing silicon content and decreasing processing temperature are consistent with grain boundary and defect scattering of conducting ions.« less

Monitoring of antisolvent crystallization of sodium scutellarein by combined FBRM-PVM-NIR.

PubMed

Liu, Xuesong; Sun, Di; Wang, Feng; Wu, Yongjiang; Chen, Yong; Wang, Longhu

2011-06-01

Antisolvent crystallization can be used as an alternative to cooling or evaporation for the separation and purification of solid product in the pharmaceutical industry. To improve the process understanding of antisolvent crystallization, the use of in-line tools is vital. In this study, the process analytical technology (PAT) tools including focused beam reflectance measurement (FBRM), particle video microscope (PVM), and near-infrared spectroscopy (NIRS) were utilized to monitor antisolvent crystallization of sodium scutellarein. FBRM was used to monitor chord count and chord length distribution of sodium scutellarein particles in the crystallizer, and PVM, as an in-line video camera, provided pictures imaging particle shape and dimension. In addition, a quantitative model of PLS was established by in-line NIRS to detect the concentration of sodium scutellarein in the solvent and good calibration statistics were obtained (r(2) = 0.976) with the residual predictive deviation value of 11.3. The discussion over sensitivities, strengths, and weaknesses of the PAT tools may be helpful in selection of suitable PAT techniques. These in-line techniques eliminate the need for sample preparation and offer a time-saving approach to understand and monitor antisolvent crystallization process. Copyright © 2011 Wiley-Liss, Inc.

A comprehensive analysis of sodium levels in the Canadian packaged food supply

PubMed Central

Arcand, JoAnne; Au, Jennifer T.C.; Schermel, Alyssa; L’Abbe, Mary R.

2016-01-01

Background Population-wide sodium reduction strategies aim to reduce the cardiovascular burden of excess dietary sodium. Lowering sodium in packaged foods, which contribute the most sodium to the diet, is an important intervention to lower population intakes. Purpose To determine sodium levels in Canadian packaged foods and evaluate the proportion of foods meeting sodium benchmark targets set by Health Canada. Methods A cross-sectional analysis of 7234 packaged foods available in Canada in 2010–11. Sodium values were obtained from the Nutrition Facts table. Results Overall, 51.4% of foods met one of the sodium benchmark levels: 11.5% met Phase 1, 11.1% met Phase 2, and 28.7% met 2016 goal (Phase 3) benchmarks. Food groups with the greatest proportion meeting goal benchmarks were dairy (52.0%) and breakfast cereals (42.2%). Overall 48.6% of foods did not meet any benchmark level and 25% of all products exceeded maximum levels. Meats (61.2%) and canned vegetables/legumes and legumes (29.6%) had the most products exceeding maximum levels. There was large variability in the range of sodium within and between food categories. Food categories highest in sodium (mg/serving) were dry, condensed and ready-to-serve soups (834 ± 256, 754 ± 163, and 636 ± 173, respectively), oriental noodles (783 ± 433), broth (642 ± 239), and frozen appetizers/sides (642 ± 292). Conclusion These data provide a critical baseline assessment for monitoring sodium levels in Canadian foods. While some segments of the market are making progress towards sodium reduction, all sectors need encouragement to continue to reduce the amount of sodium added during food processing. PMID:24842740

LITERATURE REVIEWS TO SUPPORT ION EXCHANGE TECHNOLOGY SELECTION FOR MODULAR SALT PROCESSING

DOE Office of Scientific and Technical Information (OSTI.GOV)

King, W

2007-11-30

This report summarizes the results of literature reviews conducted to support the selection of a cesium removal technology for application in a small column ion exchange (SCIX) unit supported within a high level waste tank. SCIX is being considered as a technology for the treatment of radioactive salt solutions in order to accelerate closure of waste tanks at the Savannah River Site (SRS) as part of the Modular Salt Processing (MSP) technology development program. Two ion exchange materials, spherical Resorcinol-Formaldehyde (RF) and engineered Crystalline Silicotitanate (CST), are being considered for use within the SCIX unit. Both ion exchange materials havemore » been studied extensively and are known to have high affinities for cesium ions in caustic tank waste supernates. RF is an elutable organic resin and CST is a non-elutable inorganic material. Waste treatment processes developed for the two technologies will differ with regard to solutions processed, secondary waste streams generated, optimum column size, and waste throughput. Pertinent references, anticipated processing sequences for utilization in waste treatment, gaps in the available data, and technical comparisons will be provided for the two ion exchange materials to assist in technology selection for SCIX. The engineered, granular form of CST (UOP IE-911) was the baseline ion exchange material used for the initial development and design of the SRS SCIX process (McCabe, 2005). To date, in-tank SCIX has not been implemented for treatment of radioactive waste solutions at SRS. Since initial development and consideration of SCIX for SRS waste treatment an alternative technology has been developed as part of the River Protection Project Waste Treatment Plant (RPP-WTP) Research and Technology program (Thorson, 2006). Spherical RF resin is the baseline media for cesium removal in the RPP-WTP, which was designed for the treatment of radioactive waste supernates and is currently under construction in Hanford, WA. Application of RF for cesium removal in the Hanford WTP does not involve in-riser columns but does utilize the resin in large scale column configurations in a waste treatment facility. The basic conceptual design for SCIX involves the dissolution of saltcake in SRS Tanks 1-3 to give approximately 6 M sodium solutions and the treatment of these solutions for cesium removal using one or two columns supported within a high level waste tank. Prior to ion exchange treatment, the solutions will be filtered for removal of entrained solids. In addition to Tanks 1-3, solutions in two other tanks (37 and 41) will require treatment for cesium removal in the SCIX unit. The previous SCIX design (McCabe, 2005) utilized CST for cesium removal with downflow supernate processing and included a CST grinder following cesium loading. Grinding of CST was necessary to make the cesium-loaded material suitable for vitrification in the SRS Defense Waste Processing Facility (DWPF). Because RF resin is elutable (and reusable) and processing requires conversion between sodium and hydrogen forms using caustic and acidic solutions more liquid processing steps are involved. The WTP baseline process involves a series of caustic and acidic solutions (downflow processing) with water washes between pH transitions across neutral. In addition, due to resin swelling during conversion from hydrogen to sodium form an upflow caustic regeneration step is required. Presumably, one of these basic processes (or some variation) will be utilized for MSP for the appropriate ion exchange technology selected. CST processing involves two primary waste products: loaded CST and decontaminated salt solution (DSS). RF processing involves three primary waste products: spent RF resin, DSS, and acidic cesium eluate, although the resin is reusable and typically does not require replacement until completion of multiple treatment cycles. CST processing requires grinding of the ion exchange media, handling of solids with high cesium loading, and handling of liquid wash and conditioning solutions. RF processing requires handling and evaporation of cesium eluates, disposal of spent organic resin, and handling of the various liquid wash and regenerate solutions used. In both cases, the DSS will be immobilized in a low activity waste form. It appears that both technologies are mature, well studied, and generally suitable for this application. Technology selection will likely be based on downstream impacts or preferences between the various processing options for the two materials rather than on some unacceptable performance property identified for one material. As a result, the following detailed technical review and summary of the two technologies should be useful to assist in technology selection for SCIX.« less

The TMT Adaptive Optics Program

NASA Astrophysics Data System (ADS)

Ellerbroek, Brent

2011-09-01

We provide an overview of the Thirty Meter Telescope (TMT) AO program, with an emphasis upon the progress made since the first AO4ELT conference held in 2009. The first light facility AO system for TMT is the Narrow Field Infra-Red AO System (NFIRAOS), which will provide diffraction-limited performance in the J, H, and K bands over 18-30 arc sec diameter fields with 50% sky coverage at the galactic pole. This is accomplished with order 60x60 wavefront sensing and correction, two deformable mirrors conjugate to ranges of 0 and 11.2 km, 6 sodium laser guide stars in an asterism with a diameter of 70 arc sec, and three low order (tip/tilt or tip/tilt focus), infra-red natural guide star (NGS) wavefront sensors deployable within a 2 arc minute diameter patrol field. The first light LGS asterism is generated by the Laser Guide Star Facility (LGSF), which initially incorporates 6 20-25W class laser systems mounted to the telescope elevation journal, a mirror-based beam transfer optics system, and a 0.4m diameter laser launch telescope located behind the TMT secondary mirror. Future plans for additional AO capabilities include a mid infra-red AO (MIRAO) system to support science instruments in the 4-20 micron range, a ground-layer AO (GLAO) system for wide-field spectroscopy, a multi-object AO (MOAO) system for multi-object integral field unit spectroscopy, and extreme AO (ExAO) for high contrast imaging. Significant progress has been made in developing the first-light AO architecture since 2009. This includes the adoption of a new NFIRAOS opto-mechanical design consisting of two off-axis parabola (OAP) relays in series, which eliminates field distortion and also significantly simplifies the designs of the LGS wavefront sensors, optical source simulators, and turbulence generator subsystem. The design of the LGSF has also been interated, and has been simplfied by the relocation of the (smaller, gravity invarient) laser systems to the telescope elevation journal. Protoyping activities continue for laser systems, wavefront sensing detectors, and deformable mirrors; work on the associated detector and deformable mirror electronics has also been initiated. AO Performance estimates and error budgets have been further detailed. Some of the modeling topics which have received particular attention include turbulence (Cn2) profile estimation from LGS WFS measurements, sodium layer range tracking, PSF reconstruction for multi-conjugate AO, LGS fratricide, astrometry at the galactic center, and further optimizing sky coverage and the peformance of the tip/tilt and low-order NGS mode control loops. Finally, experiments and field tests continue at the University of British Columbia LIDAR facility to measure the spatial and temporal variability of the sodium layer, and to characterize the sodium coupling efficiency of candidate laser systems for TMT.

Process for production of synthesis gas with reduced sulfur content

DOEpatents

Najjar, Mitri S.; Corbeels, Roger J.; Kokturk, Uygur

1989-01-01

A process for the partial oxidation of a sulfur- and silicate-containing carbonaceous fuel to produce a synthesis gas with reduced sulfur content which comprises partially oxidizing said fuel at a temperature in the range of 1800.degree.-2200.degree. F. in the presence of a temperature moderator, an oxygen-containing gas and a sulfur capture additive which comprises an iron-containing compound portion and a sodium-containing compound portion to produce a synthesis gas comprising H.sub.2 and CO with a reduced sulfur content and a molten slag which comprises (i) a sulfur-containing sodium-iron silicate phase and (ii) a sodium-iron sulfide phase. The sulfur capture additive may optionally comprise a copper-containing compound portion.

Iso-Oriented NaTi2(PO4)3 Mesocrystals as Anode Material for High-Energy and Long-Durability Sodium-Ion Capacitor.

PubMed

Wei, Tongye; Yang, Gongzheng; Wang, Chengxin

2017-09-20

Sodium-ion capacitors (SIC) combine the merits of both high-energy batteries and high-power electrochemical capacitors as well as the low cost and high safety. However, they are also known to suffer from the severe deficiency of suitable electrode materials with high initial Coulombic efficiency (ICE) and kinetic balance between both electrodes. Herein, we report a facile solvothermal synthesis of NaTi 2 (PO 4 ) 3 nanocages constructed by iso-oriented tiny nanocrystals with a mesoporous architecture. It is notable that the NaTi 2 (PO 4 ) 3 mesocrystals exhibit a large ICE of 94%, outstanding rate capability (98 mA h g -1 at 10 C), and long cycling life (over 77% capacity retention after 10 000 cycles) in half cells, all of which are in favor to be utilized into a full cell. When assembled with commercial activated carbon to an SIC, the system delivers an energy density of 56 Wh kg -1 at a power density of 39 W kg -1 . Even at a high current rate of 5 A g -1 (corresponds to finish a full charge/discharge process in 2 min), the SIC still works well after 20 000 cycles without obvious capacity degradation. With the merits of impressive energy/power densities and longevity, the obtained hybrid capacitor should be a promising device for highly efficient energy storage systems.

ZnS-Sb2S3@C Core-Double Shell Polyhedron Structure Derived from Metal-Organic Framework as Anodes for High Performance Sodium Ion Batteries.

PubMed

Dong, Shihua; Li, Caixia; Ge, Xiaoli; Li, Zhaoqiang; Miao, Xianguang; Yin, Longwei

2017-06-27

Taking advantage of zeolitic imidazolate framework (ZIF-8), ZnS-Sb 2 S 3 @C core-double shell polyhedron structure is synthesized through a sulfurization reaction between Zn 2+ dissociated from ZIF-8 and S 2- from thioacetamide (TAA), and subsequently a metal cation exchange process between Zn 2+ and Sb 3+ , in which carbon layer is introduced from polymeric resorcinol-formaldehyde to prevent the collapse of the polyhedron. The polyhedron composite with a ZnS inner-core and Sb 2 S 3 /C double-shell as anode for sodium ion batteries (SIBs) shows us a significantly improved electrochemical performance with stable cycle stability, high Coulombic efficiency and specific capacity. Peculiarly, introducing a carbon shell not only acts as an important protective layer to form a rigid construction and accommodate the volume changes, but also improves the electronic conductivity to optimize the stable cycle performance and the excellent rate property. The architecture composed of ZnS inner core and a complex Sb 2 S 3 /C shell not only facilitates the facile electrolyte infiltration to reduce the Na-ion diffusion length to improve the electrochemical reaction kinetics, but also prevents the structure pulverization caused by Na-ion insertion/extraction. This approach to prepare metal sulfides based on MOFs can be further extended to design other nanostructured systems for high performance energy storage devices.

Recovery of Iron from Hematite-Rich Diasporic-Type Bauxite Ore

NASA Astrophysics Data System (ADS)

Jiang, Tao; Li, Zhuoxuan; Yang, Lin; Li, Guanghui; Zhang, Yuanbo; Zeng, Jinghua

A technique has been proposed for recovering iron from hematite-rich diasporic-type bauxite ore in this study. Direct reduction roasting followed by low intensity wet magnetic separation process was carried out. The parameters including reduction temperature and time, sodium salts, grinding conditions and magnetic field intensity for separation of iron were determined. The optimum process parameters as follows: roasting temperature of 1050 °C, time of 60 min, sodium salts involving sodium sulfate, borax, sodium carbonate with dosages of 10 wt%, 2 wt%, 35 wt% respectively, and magnetic field intensity of 1000 Gs with fineness of pulp reached 92.75% passing -0.074mm. Under the optimal conditions, an iron concentrate containing 88.17% total iron grade and iron recovery of 92.51% was obtained, 4.55% total iron grade in tailings. This novel technique provide a potential route for utilizing hematiterich diasporic bauxite ore, recovering iron resource firstly, and extracting alumina from magnetic separation tailings further.

Detection of malondialdehyde in processed meat products without interference from the ingredients.

PubMed

Jung, Samooel; Nam, Ki Chang; Jo, Cheorun

2016-10-15

Our aim was to develop a method for accurate quantification of malondialdehyde (MDA) in meat products. MDA content of uncured ground pork (Control); ground pork cured with sodium nitrite (Nitrite); and ground pork cured with sodium nitrite, sodium chloride, sodium pyrophosphate, maltodextrin, and a sausage seasoning (Mix) was measured by the 2-thiobarbituric acid (TBA) assay with MDA extraction by trichloroacetic acid (method A) and two high-performance liquid chromatography (HPLC) methods: i) HPLC separation of the MDA-dinitrophenyl hydrazine adduct (method B) and ii) HPLC separation of MDA (method C) after MDA extraction with acetonitrile. Methods A and B could not quantify MDA accurately in groups Nitrite and Mix. Nevertheless, MDA in groups Control, Nitrite, and Mix was accurately quantified by method C with good recovery. Therefore, direct MDA quantification by HPLC after MDA extraction with acetonitrile (method C) is useful for accurate measurement of MDA content in processed meat products. Copyright © 2016 Elsevier Ltd. All rights reserved.

Hierarchical Na-doped cubic ZrO2 synthesis by a simple hydrothermal route and its application in biodiesel production

NASA Astrophysics Data System (ADS)

Lara-García, Hugo A.; Romero-Ibarra, Issis C.; Pfeiffer, Heriberto

2014-10-01

Hierarchical growth of cubic ZrO2 phase was successfully synthesized via a simple hydrothermal process in the presence of different surfactants (cationic, non-ionic and anionic) and sodium hydroxide. The structural and microstructural characterizations of different ZrO2 powders were performed using various techniques, such as X-ray diffraction, transmission electron microscopy, N2 adsorption-desorption, scanning electron microscopy and infrared. Results indicated that sodium addition stabilized the cubic ZrO2 phase by a Na-doping process, independently of the surfactant used. In contrast, microstructural characteristics varied as a function of the surfactant and sodium presence. In addition, water vapor (H2O) and carbon dioxide (CO2) sorption properties were evaluated on ZrO2 samples. Results evidenced that sample surface reactivity changed as a function of the sodium content. Finally, this surface reactivity was evaluated on the biodiesel transesterification reaction using the different synthesized samples, obtaining yields of 93%.

Observations and Models of the Lunar Sodium Exosphere 1988 - 1999

NASA Technical Reports Server (NTRS)

Killen, Rosemary; Sarantos, Menelaos; Hurley, Dana M.; Potter, Andrew E.; Morgan, Thomas H.; Farrell, William M.; Naidu, Shantanu

2012-01-01

Sodium in the lunar exosphere is easily observed from the Earth's surface due to its strong resonance emission lines in the visible region of the spectrum. Although sodium is a trace element, it is easily ejected from the surface by a number of processes. The variation of this exospheric constituent both spatially and temporally can help to constrain these sources and the loss processes and their timescales. Due to a revival of interest in the Moon and its volatiles, observations of the lunar exosphere obtained at the McMath-Pierce solar telescope in 1998 and 1999 have recently been reduced and analyzed. In addition, observations of the lunar sodium exosphere obtained with the Mt. Lemmon Lunar Coronagraph on Mt. Lemmon, Arizona, have also been published. We combine these new data with data previously published and reanalyzed by Sarantos et al. This comprehensive data set will be modeled using both a simple Chamberlain exosphere model and a comprehensive Monte Carlo model.

Brain intra- and extracellular sodium concentration in multiple sclerosis: a 7 T MRI study.

PubMed

Petracca, Maria; Vancea, Roxana O; Fleysher, Lazar; Jonkman, Laura E; Oesingmann, Niels; Inglese, Matilde

2016-03-01

Intra-axonal accumulation of sodium ions is one of the key mechanisms of delayed neuro-axonal degeneration that contributes to disability accrual in multiple sclerosis. In vivo sodium magnetic resonance imaging studies have demonstrated an increase of brain total sodium concentration in patients with multiple sclerosis, especially in patients with greater disability. However, total sodium concentration is a weighted average of intra- and extra-cellular sodium concentration whose changes reflect different tissue pathophysiological processes. The in vivo, non-invasive measurement of intracellular sodium concentration is quite challenging and the few applications in patients with neurological diseases are limited to case reports and qualitative assessments. In the present study we provide first evidence of the feasibility of triple quantum filtered (23)Na magnetic resonance imaging at 7 T, and provide in vivo quantification of global and regional brain intra- and extra-cellular sodium concentration in 19 relapsing-remitting multiple sclerosis patients and 17 heathy controls. Global grey matter and white matter total sodium concentration (respectively P < 0.05 and P < 0.01), and intracellular sodium concentration (both P < 0.001) were higher while grey matter and white matter intracellular sodium volume fraction (indirect measure of extracellular sodium concentration) were lower (respectively P = 0.62 and P < 0.001) in patients compared with healthy controls. At a brain regional level, clusters of increased total sodium concentration and intracellular sodium concentration and decreased intracellular sodium volume fraction were found in several cortical, subcortical and white matter regions when patients were compared with healthy controls (P < 0.05 family-wise error corrected for total sodium concentration, P < 0.05 uncorrected for multiple comparisons for intracellular sodium concentration and intracellular sodium volume fraction). Measures of total sodium concentration and intracellular sodium volume fraction, but not measures of intracellular sodium concentration were correlated with T2-weighted and T1-weighted lesion volumes (0.05 < P < 0.01) and with Expanded Disability Status Scale (P < 0.05). Thus, suggesting that while intracellular sodium volume fraction decrease could reflect expansion of extracellular space due to tissue loss, intracellular sodium concentration increase could reflect neuro-axonal metabolic dysfunction. © The Author (2016). Published by Oxford University Press on behalf of the Guarantors of Brain. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Progress Report on Rotating Liquid Liner Implosion Experiment, 1 June to 31 December 1975.

DTIC Science & Technology

A critical question in the use of imploding liner flux compression for controlled fusion has been the stability of the inner surface of the liner ...To study the problem experimentally, the existing NRL Imploding Liner Facility was modified to allow the implosion of rotating liquid metal liners ...Rotational stabilization of lthe inner surface of a decelerating liquid sodium-potassium liner has been demonstrated, with excellent circularity of the

Sodium Content of Foods Contributing to Sodium Intake: Comparison between Selected Foods from the CDC Packaged Food Database and the USDA National Nutrient Database for Standard Reference

PubMed Central

Maalouf, Joyce; Cogswell, Mary E.; Yuan, Keming; Martin, Carrie; Gillespie, Cathleen; Ahuja, Jaspreet KC; Pehrsson, Pamela; Merritt, Robert

2015-01-01

The sodium concentration (mg/100g) for 23 of 125 Sentinel Foods (e.g. white bread) were identified in the 2009 CDC Packaged Food Database (PFD) and compared with data in the USDA’s 2013 National Nutrient Database for Standard Reference(SR 26). Sentinel Foods are foods identified by USDA to be monitored as primary indicators to assess the changes in the sodium content of commercially processed foods from stores and restaurants. Overall, 937 products were evaluated in the CDC PFD, and between 3 (one brand of ready-to-eat cereal) and 126 products (white bread) were evaluated per selected food. The mean sodium concentrations of 17 of the 23 (74%) selected foods in the CDC PFD were 90%–110% of the mean sodium concentrations in SR 26 and differences in sodium concentration were statistically significant for 6 Sentinel Foods. The sodium concentration of most of the Sentinel Foods, as selected in the PFD, appeared to represent the sodium concentrations of the corresponding food category. The results of our study help improve the understanding of how nutrition information compares between national analytic values and the label and whether the selected Sentinel Foods represent their corresponding food category as indicators for assessment of change of the sodium content in the food supply. PMID:26484010

Stages of Behavioral Change for Reducing Sodium Intake in Korean Consumers: Comparison of Characteristics Based on Social Cognitive Theory.

PubMed

Ahn, So-Hyun; Kwon, Jong Sook; Kim, Kyungmin; Kim, Hye-Kyeong

2017-07-27

High sodium intake increases the risk of cardiovascular disease. Given the importance of behavioral changes to reducing sodium intake, this study aims to investigate the stages of change and the differences in cognitive and behavioral characteristics by stage in Korean consumers. Adult participants ( N = 3892) completed a questionnaire on the stages of behavioral change, recognition of social efforts, outcome expectancy, barriers to practice, nutrition knowledge and dietary behaviors, and self-efficiency related to reduced sodium intake. The numbers of participants in each stage of behavioral change for reducing sodium intake was 29.5% in the maintenance stage, 19.5% in the action stage, and 51.0% in the preaction stage that included the precontemplation, contemplation, and preparation stages. Multiple logistic regression showed that the factors differentiating the three stages were recognizing a supportive social environment, perceived barriers to the practice of reducing sodium intake, and self-efficacy to be conscious of sodium content and to request less salt when eating out. Purchasing experience of sodium-reduced products for salty foods, knowledge of the recommended intake of salt and the difference between sodium and salt, and improving dietary habits of eating salted fish, processed food, and salty snacks were factors for being in the action stage versus the preaction stage. These findings suggest that tailored intervention according to the characteristics of each stage is helpful in reducing sodium intake.

A facile synthesis of metal nanoparticle - graphene composites for better absorption of solar radiation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sharma, Bindu; Mulla, Rafiq; Rabinal, M. K., E-mail: mkrabinal@yahoo.com

2015-06-24

Herein, a facile chemical approach has been adopted to prepare silver nanoparticles (AgNPs)- graphene (G) composite to study photothermal effect. Sodium borohydride (SBH), a strong reducing agent has been selected for this work. Effect of SBH concentrations on optical behavior of AgNPs-G composite was also investigated. Resultant materials were characterized by various techniques including X-ray diffraction (XRD), fourier transform infrared spectroscopy (FTIR), optical absorption, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). SEM micrographs confirm wrapping of AgNPs into graphene whereas XRD analysis reveals their particle size variation between 47 nm to 69 nm. Optical studies throw a light on theirmore » strong absorption behavior towards solar radiation.« less

Dietary sodium intake: scientific basis for public policy.

PubMed

Whelton, Paul K

2015-01-01

National and international agencies recommend a reduction in dietary sodium intake. However, some have questioned the wisdom of these policies. The goal of this report was to assess the findings and quality of studies that have examined the relationship between dietary sodium and both blood pressure and cardiovascular disease. Literature review of the available observational studies and randomized controlled trials, including systematic reviews and meta-analyses. A large body of evidence from observational studies and clinical trials documents a direct relationship between dietary sodium intake and the level of blood pressure, especially in persons with a higher level of blood pressure, African-Americans, and those who are older or have comorbidity, including chronic kidney disease. A majority of the available observational reports support the presence of a direct relationship between dietary sodium intake and cardiovascular disease but the quality of the evidence according to most studies is poor. The limited information available from clinical trials is consistent with a beneficial effect of reduced sodium intake on incidence of cardiovascular disease. The scientific underpinning for policies to reduce the usual intake of dietary sodium is strong. In the United States and many other countries, addition of sodium during food processing has led to a very high average intake of dietary sodium, with almost everyone exceeding the recommended goals. National programs utilizing voluntary and mandatory approaches have resulted in a successful reduction in sodium intake. Even a small reduction in sodium consumption is likely to yield sizable improvement in population health. © 2015 S. Karger AG, Basel.

Ancient Systems of Sodium/Potassium Homeostasis as Predecessors of Membrane Bioenergetics.

PubMed

Dibrova, D V; Galperin, M Y; Koonin, E V; Mulkidjanian, A Y

2015-05-01

Cell cytoplasm of archaea, bacteria, and eukaryotes contains substantially more potassium than sodium, and potassium cations are specifically required for many key cellular processes, including protein synthesis. This distinct ionic composition and requirements have been attributed to the emergence of the first cells in potassium-rich habitats. Different, albeit complementary, scenarios have been proposed for the primordial potassium-rich environments based on experimental data and theoretical considerations. Specifically, building on the observation that potassium prevails over sodium in the vapor of inland geothermal systems, we have argued that the first cells could emerge in the pools and puddles at the periphery of primordial anoxic geothermal fields, where the elementary composition of the condensed vapor would resemble the internal milieu of modern cells. Marine and freshwater environments generally contain more sodium than potassium. Therefore, to invade such environments, while maintaining excess of potassium over sodium in the cytoplasm, primordial cells needed means to extrude sodium ions. The foray into new, sodium-rich habitats was the likely driving force behind the evolution of diverse redox-, light-, chemically-, or osmotically-dependent sodium export pumps and the increase of membrane tightness. Here we present a scenario that details how the interplay between several, initially independent sodium pumps might have triggered the evolution of sodium-dependent membrane bioenergetics, followed by the separate emergence of the proton-dependent bioenergetics in archaea and bacteria. We also discuss the development of systems that utilize the sodium/potassium gradient across the cell membranes.

Sodium Intake among US School-Aged Children: National Health and Nutrition Examination Survey, 2011–2012

PubMed Central

Quader, Zerleen S.; Gillespie, Cathleen; Sliwa, Sarah A.; Ahuja, Jaspreet K. C.; Burdg, Jinee P.; Moshfegh, Alanna; Pehrsson, Pamela R.; Gunn, Janelle P.; Mugavero, Kristy; Cogswell, Mary E.

2017-01-01

Background Identifying current major dietary sources of sodium can enhance strategies to reduce excess sodium intake, which occurs among 90% of US school-aged children. Objective To describe major food sources, places obtained, and eating occasions contributing to sodium intake among US school-aged children. Design Cross-sectional analysis of data from the 2011–2012 National Health and Nutrition Examination Survey. Participants/setting A nationally representative sample of 2,142 US children aged 6 to 18 years who completed a 24-hour dietary recall. Main outcome measures Population proportions of sodium intake from major food categories, places, and eating occasions. Statistical analyses performed Statistical analyses accounted for the complex survey design and sampling. Wald F tests and t tests were used to examine differences between subgroups. Results Average daily sodium intake was highest among adolescents aged 14 to 18 years (3,565±120 mg), lowest among girls (2,919±74 mg). Little variation was seen in average intakes or the top five sodium contributors by sociodemographic characteristics or weight status. Ten food categories contributed to almost half (48%) of US school-aged children’s sodium intake, and included pizza, Mexican-mixed dishes, sandwiches, breads, cold cuts, soups, savory snacks, cheese, plain milk, and poultry. More than 80 food categories contributed to the other half of children’s sodium intake. Foods obtained from stores contributed 58% of sodium intake, fast-food/pizza restaurants contributed 16%, and school cafeterias contributed 10%. Thirty-nine percent of sodium intake was consumed at dinner, 31% at lunch, 16% from snacks, and 14% at breakfast. Conclusions With the exception of plain milk, which naturally contains sodium, the top 10 food categories contributing to US schoolchildren’s sodium intake during 2011–2012 comprised foods in which sodium is added during processing or preparation. Sodium is consumed throughout the day from multiple foods and locations, highlighting the importance of sodium reduction across the US food supply. PMID:27818138

Effects of Whole-Body VX Vapor Exposure on Lethality in Rats

DTIC Science & Technology

2007-01-01

J. "New Method for Hemoglobin Determination by Using Sodium Lauryl Sulfate (SLS)." Clin. Biochem. 15(1) 83-88 (1982). Prins, J, "Product and Process...regenerated VX-G and deuterated internal standard VX-G were eluted with I mL ethyl acetate that was collected and dried over anhydrous sodium sulfate ...anhydrous sodium sulfate . The ethyl acetate was removed from the collection tube and filtered through a 0.2 lim nylon Acrodisc syringe filter (Pall Gelman

Engineering and Development Support of General Decon Technology for the DARCOM Installation Restoration Program. Task 4. General Technology Literature Searches (II) Solidification Techniques for Lagoon Waters

DTIC Science & Technology

1980-12-01

40.8 Sodium 70.1 Zinc 0.01 37 The process includes the following steps (Pichat et al., 1979): - neutralization precipitation (silicates, borates...Compressive Strength of Polyester - Encapsulated Sodium Sulfate Waste Composite ....... .............. 64 9. Deep Chemical Mixer Mounted on a Barge...zinc, copper, lead, manganese and tin; sodium salts of arsenate, borate, phosphate, iodate, and sulfide; and sulfate salts. Sulfate salts form calcium

Development of biodegradable foamlike materials based on casein and sodium montmorillonite clay

USDA-ARS?s Scientific Manuscript database

Biodegradable foamlike materials based on a naturally occurring polymer (casein protein) and sodium montmorillonite clay (Na+-MMT) were produced through a simple freeze-drying process. By utilizing DL-glyceraldehyde (GC) as a chemical cross-linking agent, the structural integrity of these new aeroge...

40 CFR 60.281 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... cooking (digesting) wood chips in a water solution of sodium hydroxide and sodium sulfide (white liquor) at high temperature and pressure. Regeneration of the cooking chemicals through a recovery process is... any operation in which pulp is produced from wood by cooking (digesting) wood chips in a solution of...

Water and mineral relations of Atriplex canescens and A. cuneata on saline processed oil shale

DOE Office of Scientific and Technical Information (OSTI.GOV)

Richardson, S.G.

1979-01-01

Growth, mineral uptake and water relations of Atriplex canescens and A. cuneata, both native to the arid oil shale region of northeastern Utah, were studied in the greenhouse and laboratory as affected by various salinity levels and specific ions in processed oil shale. Salinity of the shale was manipulated by moistening leached processed oil shale to near field capacity (20% H/sub 2/O by weight) with solutions of shale leachate, sodium sulfate, magnesium sulfate or sodium chloride at equiosmotic concentrations ranging from 0 to -30 bars. Although shale salinity did not affect osmotic adjustment, zero turgor points of A. canescens becamemore » more negative with reductions in shale moisture percentage. Differences in plant growth due to differet ions in the soil solution could not be explained by effects on osmotic adjustment. However, greater growth of A. canescens in Na/sub 2/SO/sub 4/ treated than MgSO/sub 4/ treated leached shale was associated with greater leaf succulence, greater lamina lengths and lamina widths and lower diffusive leaf resistances. Potassium added to leached and unleached processed oil shale increased shoot and root biomass production, shoot/root ratio, leaf K content, and water use efficiency of a sodium-excluding Atriplex canescens biotype but did not increase growth of a sodium-accumulating biotype.« less

ICPP tank farm closure study. Volume 1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Spaulding, B.C.; Gavalya, R.A.; Dahlmeir, M.M.

1998-02-01

The disposition of INEEL radioactive wastes is now under a Settlement Agreement between the DOE and the State of Idaho. The Settlement Agreement requires that existing liquid sodium bearing waste (SBW), and other liquid waste inventories be treated by December 31, 2012. This agreement also requires that all HLW, including calcined waste, be disposed or made road ready to ship from the INEEL by 2035. Sodium bearing waste (SBW) is produced from decontamination operations and HLW from reprocessing of SNF. SBW and HLW are radioactive and hazardous mixed waste; the radioactive constituents are regulated by DOE and the hazardous constituentsmore » are regulated by the Resource Conservation and Recovery Act (RCRA). Calcined waste, a dry granular material, is produced in the New Waste Calcining Facility (NWCF). Two primary waste tank storage locations exist at the ICPP: Tank Farm Facility (TFF) and the Calcined Solids Storage Facility (CSSF). The TFF has the following underground storage tanks: four 18,400-gallon tanks (WM 100-102, WL 101); four 30,000-gallon tanks (WM 103-106); and eleven 300,000+ gallon tanks. This includes nine 300,000-gallon tanks (WM 182-190) and two 318,000 gallon tanks (WM 180-181). This study analyzes the closure and subsequent use of the eleven 300,000+ gallon tanks. The 18,400 and 30,000-gallon tanks were not included in the work scope and will be closed as a separate activity. This study was conducted to support the HLW Environmental Impact Statement (EIS) waste separations options and addresses closure of the 300,000-gallon liquid waste storage tanks and subsequent tank void uses. A figure provides a diagram estimating how the TFF could be used as part of the separations options. Other possible TFF uses are also discussed in this study.« less

A Top-Down Strategy toward SnSb In-Plane Nanoconfined 3D N-Doped Porous Graphene Composite Microspheres for High Performance Na-Ion Battery Anode.

PubMed

Qin, Jian; Wang, Tianshuai; Liu, Dongye; Liu, Enzuo; Zhao, Naiqin; Shi, Chunsheng; He, Fang; Ma, Liying; He, Chunnian

2018-03-01

Engineering of 3D graphene/metal composites with ultrasmall sized metal and robust metal-graphene interfacial interaction for energy storage application is still a challenge and rarely reported. In this work, a facile top-down strategy is developed for the preparation of SnSb-in-plane nanoconfined 3D N-doped porous graphene networks for sodium ion battery anodes, which are composed of several tens of interconnected empty N-graphene boxes in-plane firmly embedded with ultrasmall SnSb nanocrystals. The all-around encapsulation (plane-to-plane contact) architecture that provides a large interface between N-graphene and SnSb nanocrystal not only effectively enhances the electron conductivity and structural integrity of the overall electrode, but also offers excess interfacial sodium storage, thus leading to much enhanced high-rate sodium storage capacity and stability, which has been proven by both experimental results and first-principles simulations. Moreover, this top-down strategy can enable new paths to the low-cost and high-yield synthesis of 3D graphene/metal composites for applications in energy-related fields and beyond. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

General One-Pot Synthesis of Transition-Metal Phosphide/Nitrogen-Doped Carbon Hybrid Nanosheets as Ultrastable Anodes for Sodium-Ion Batteries.

PubMed

Li, Jingjing; Shi, Liang; Gao, Jingyu; Zhang, Genqiang

2018-01-26

Sodium-ion batteries (SIBs) have been considered as promising energy storage devices in grid-level applications, owing to their largely reduced cost compared with that of lithium-ion batteries. However, the practical application of SIBs has been seriously hindered because of the lack of appropriate anode materials, limited by the thermodynamics perspective, which is one of the central task at current stage. Herein, we have developed a general one-pot strategy for the synthesis of transition-metal phosphide (TMP) based hybrid nanosheets composed of carbon-coated TMP nanoparticles anchored to the surface of nitrogen-doped carbon nanosheets. This facile and cost-effective method is quite universal and holds potential to be further extended to other metal phosphide materials. Significantly, the hybrid nanosheet electrode possesses excellent sodium storage properties as anodes for SIBs, including high specific capacity, an ultra-long cycle life and a remarkable rate performance. This work makes a significant contribution to not only the synthetic methodology of TMP-carbon two-dimensional hybrid nanostructures, but also the application of TMP-based anodes for high-energy SIBs. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

SnS2 /Sb2 S3 Heterostructures Anchored on Reduced Graphene Oxide Nanosheets with Superior Rate Capability for Sodium-Ion Batteries.

PubMed

Wang, Shijian; Liu, Shuaishuai; Li, Xuemei; Li, Cong; Zang, Rui; Man, Zengming; Wu, Yuhan; Li, Pengxin; Wang, Guoxiu

2018-03-12

Tin disulfide, as a promising high-capacity anode material for sodium-ion batteries, exhibits high theoretical capacity but poor practical electrochemical properties due to its low electrical conductivity. Constructing heterostructures has been considered to be an effective approach to enhance charge transfer and ion-diffusion kinetics. In this work, composites of SnS 2 /Sb 2 S 3 heterostructures with reduced graphene oxide nanosheets were synthesized by a facile one-pot hydrothermal method. When applied as anode material in sodium-ion batteries, the composite showed a high reversible capacity of 642 mA h g -1 at a current density of 0.2 A g -1 and good cyclic stability without capacity loss in 100 cycles. In particular, SnS 2 /Sb 2 S 3 heterostructures exhibited outstanding rate performance with capacities of 593 and 567 mA h g -1 at high current densities of 2 and 4 A g -1 , respectively, which could be ascribed to the dramatically improved Na + diffusion kinetics and electrical conductivity. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

In-situ carbon-coated Na2FeP2O7 anchored in three-dimensional reduced graphene oxide framework as a durable and high-rate sodium-ion battery cathode

NASA Astrophysics Data System (ADS)

Chen, Xiaobin; Du, Ke; Lai, Yanqing; Shang, Guozhi; Li, Huangxu; Xiao, Zhiwei; Chen, Yuxiang; Li, Junming; Zhang, Zhian

2017-07-01

Na2FeP2O7, which is considered as a promising cathode for sodium ion batteries (SIBs) on account of its economical efficiency and outstanding thermal stability, has been widely studied for the purpose of enhancing its electronic conductivity and interface ion transportation. In this paper, a double-carbon synergistically modified strategy was firstly introduced to facilitate the electrochemical performance of Na2FeP2O7. Na2FeP2O7 particles are enwrapped in situ by a carbon layer and further anchored in reduced graphene oxide (RGO) framework through a facile urea-nitrate combustion method. Consequently, the excellent rate performance and durable cycle stability of this compound are identified, which exhibits a reversible sodium storage capacity of 65 mAh g-1 at a current density of 10 C and no obvious decay in capacity after circling for 300 cycles at 1 C. What's more, no drastic degradation in capacity is observed when the cycling current density is brought back to high rates after cycling for more than 360 cycles at various rates.

Electrochemical route to the synthesis of ZnO microstructures: its nestlike structure and holding of Ag particles

PubMed Central

2013-01-01

Abstract A simple and facile electrochemical route was developed for the shape-selective synthesis of large-scaled series of ZnO microstructures, including petal, flower, sphere, nest and clew aggregates of ZnO laminas at room temperature. This route is based on sodium citrate-directed crystallization. In the system, sodium citrate can greatly promote ZnO to nucleate and directly grow by selectively capping the specific ZnO facets because of its excellent adsorption ability. The morphology of ZnO is tuned by readily adjusting the concentration of sodium citrate and the electrodeposition time. Among the series structures, the remarkable ZnO nestlike structure can be used as a container to hold not only the interlaced ZnO laminas but also Ag nanoparticles in the center. The special heterostructures of nestlike ZnO holding Ag nanoparticles were found to display the superior properties on the surface-enhanced Raman scattering. This work has signified an important methodology to produce a wide assortment of desired microstructures of ZnO. PACS 81 Materials science 81.07.-b nanoscale materials and structures Fabrication Characterization 81.15.-z Methods of deposition of films Coatings Film growth and epitaxy. PMID:23414592

Reverse microemulsion synthesis of nickel-cobalt hexacyanoferrate/reduced graphene oxide nanocomposites for high-performance supercapacitors and sodium ion batteries

NASA Astrophysics Data System (ADS)

Qiu, Xiaoming; Liu, Yongchang; Wang, Luning; Fan, Li-Zhen

2018-03-01

Prussian blue analogues with tunable open channels are of fundamental and technological importance for energy storage systems. Herein, a novel facile synthesis of nickel-cobalt hexacyanoferrate/reduced graphene oxide (denoted as Ni-CoHCF/rGO) nanocomposite is realized by a reverse microemulsion method. The very fine Ni-CoHCF nanoparticles (10-20 nm) are homogeneously anchored on the surface of reduced graphene oxide by electrostatic adsorption and reduced graphene oxide is well-separated by Ni-CoHCF particles. Benefiting from the combined advantages of this structure, the Ni-. It CoHCF/rGO nanocomposite can be used as electrodes for both supercapacitors and sodium ion batteries exhibits excellent pseudocapacitve performance in terms of high specific capacitance of 466 F g-1 at 0.2 A g-1 and 350 F g-1 at 10 A g-1, along with high cycling stabilities. As a cathode material for sodium ion batteries, it also demonstrates a high reversible capacity of 118 mAh g-1 at 0.1 A g-1, good rate capability, and superior cycling stability. These results suggest its potential as an efficient electrode for high-performance energy storage and renewable delivery devices.

Projected Impact of a Sodium Consumption Reduction Initiative in Argentina: An Analysis from the CVD Policy Model – Argentina

PubMed Central

Konfino, Jonatan; Mekonnen, Tekeshe A.; Coxson, Pamela G.; Ferrante, Daniel; Bibbins-Domingo, Kirsten

2013-01-01

Background Cardiovascular disease (CVD) is the leading cause of death in adults in Argentina. Sodium reduction policies targeting processed foods were implemented in 2011 in Argentina, but the impact has not been evaluated. The aims of this study are to use Argentina-specific data on sodium excretion and project the impact of Argentina’s sodium reduction policies under two scenarios - the 2-year intervention currently being undertaken or a more persistent 10 year sodium reduction strategy. Methods We used Argentina-specific data on sodium excretion by sex and projected the impact of the current strategy on sodium consumption and blood pressure decrease. We assessed the projected impact of sodium reduction policies on CVD using the Cardiovascular Disease (CVD) Policy Model, adapted to Argentina, modeling two alternative policy scenarios over the next decade. Results Our study finds that the initiative to reduce sodium consumption currently in place in Argentina will have substantial impact on CVD over the next 10 years. Under the current proposed policy of 2-year sodium reduction, the mean sodium consumption is projected to decrease by 319–387 mg/day. This decrease is expected to translate into an absolute reduction of systolic blood pressure from 0.93 mmHg to 1.81 mmHg. This would avert about 19,000 all-cause mortality, 13,000 total myocardial infarctions, and 10,000 total strokes over the next decade. A more persistent sodium reduction strategy would yield even greater CVD benefits. Conclusion The impact of the Argentinean initiative would be effective in substantially reducing mortality and morbidity from CVD. This paper provides evidence-based support to continue implementing strategies to reduce sodium consumption at a population level. PMID:24040085

Assessment of a Hydroxyapatite Permeable Reactive Barrier to Remediate Uranium at the Old Rifle Site Colorado.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moore, Robert C.; Szecsody, James; Rigali, Mark J.

We have performed an initial evaluation and testing program to assess the effectiveness of a hydroxyapatite (Ca10(PO4)6(OH)2) permeable reactive barrier and source area treatment to decrease uranium mobility at the Department of Energy (DOE) former Old Rifle uranium mill processing site in Rifle, western Colorado. Uranium ore was processed at the site from the 1940s to the 1970s. The mill facilities at the site as well as the uranium mill tailings previously stored there have all been removed. Groundwater in the alluvial aquifer beneath the site still contains elevated concentrations of uranium, and is currently used for field tests tomore » study uranium behavior in groundwater and investigate potential uranium remediation technologies. The technology investigated in this work is based on in situ formation of apatite in sediment to create a subsurface apatite PRB and also for source area treatment. The process is based on injecting a solution containing calcium citrate and sodium into the subsurface for constructing the PRB within the uranium plume. As the indigenous sediment micro-organisms biodegrade the injected citrate, the calcium is released and reacts with the phosphate to form hydroxyapatite (precipitate). This paper reports on proof-of-principle column tests with Old Rifle sediment and synthetic groundwater.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Josephson, Gary B.; Geeting, John GH; Bredt, Ofelia P.

Pacific Northwest National Laboratory (PNNL) has been tasked by Bechtel National Inc. (BNI) on the River Protection Project-Waste Treatment Plant (RPP-WTP) project to perform research and development activities to resolve technical issues identified for the Pretreatment Facility (PTF). The Pretreatment Engineering Platform (PEP) was designed, constructed, and operated as part of a plan to respond to issue M12, "Undemonstrated Leaching Processes." The PEP is a 1/4.5-scale test platform designed to simulate the WTP pretreatment caustic leaching, oxidative leaching, ultrafiltration solids concentration, and slurry washing processes. The PEP replicates the WTP leaching processes using prototypic equipment and control strategies. The PEPmore » also includes non-prototypic ancillary equipment to support the core processing. Two operating scenarios are currently being evaluated for the ultrafiltration process (UFP) and leaching operations. The first scenario has caustic leaching performed in the UFP-2 ultrafiltration feed vessels (i.e., vessel UFP-VSL-T02A in the PEP; and vessels UFP-VSL-00002A and B in the WTP PTF). The second scenario has caustic leaching conducted in the UFP-1 ultrafiltration feed preparation vessels (i.e., vessels UFP-VSL-T01A and B in the PEP; vessels UFP-VSL-00001A and B in the WTP PTF). In both scenarios, 19-M sodium hydroxide solution (NaOH, caustic) is added to the waste slurry in the vessels to leach solid aluminum compounds (e.g., gibbsite, boehmite). Caustic addition is followed by a heating step that uses direct injection of steam to accelerate the leach process. Following the caustic leach, the vessel contents are cooled using vessel cooling jackets and/or external heat exchangers. The main difference between the two scenarios is that for leaching in UFP-1, the 19-M NaOH is added to un-concentrated waste slurry (3-8 wt% solids), while for leaching in UFP-2, the slurry is concentrated to nominally 20 wt% solids using cross-flow ultrafiltration before the addition of caustic. In both scenarios, following the caustic leach, the slurry was then concentrated to 17 wt% and washed with inhibited water to remove NaOH and other soluble salts. Next, the slurry was oxidatively leached using sodium permanganate to solubilize chrome. The slurry was then washed to remove the dissolved chrome and concentrated.« less

Legal Regulation of Sodium Consumption to Reduce Chronic Conditions

PubMed Central

Barraza, Leila F.

2016-01-01

In the United States, tens of thousands of Americans die each year of heart disease, stroke, or other chronic conditions tied to hypertension from long-term overconsumption of sodium compounds. Major strides to lower dietary sodium have been made over decades, but the goal of reducing Americans’ daily consumption is elusive. The Food and Drug Administration (FDA) has been urged to consider stronger regulatory limits on sodium, especially in processed and prepared foods. Still, FDA categorizes salt (and many other sodium compounds) as “generally recognized as safe,” meaning they can be added to foods when ingested in reasonable amounts. Legal reforms or actions at each level of government offer traditional and new routes to improving chronic disease outcomes. However, using law as a public health tool must be assessed carefully, given potential trade-offs and unproven efficacy. PMID:26890409

PROCESS FOR THE SEPARATION OF HEAVY METALS

DOEpatents

Gofman, J.W.; Connick, R.E.; Wahl, A.C.

1959-01-27

A method is presented for thc separation of plutonium from uranium and the fission products with which it is associated. The method is based on the fact that hexavalent plutonium forms an insoluble complex precipitate with sodium acetate, as does the uranyl ion, while reduced plutonium is not precipitated by sodium acetate. Several embodiments are shown, e.g., a solution containing plutonium and uranium in the hexavalent state may be contacted with sodium acetate causing the formation of a sodium uranyl acetate precipitate which carries the plutonium values while the fission products remain in solution. If the original solution is treated with a reducing agent, so that the plutonium is reduced while the uranium remains in the hexavalent state, and sodium and acetate ions are added, the uranium will precipitutc while the plutonium remains in solution effecting separation of the Pu from urarium.

PERCHLORATE LEVELS IN SAMPLES OF SODIUM NITRATE FERTILIZER DERIVED FROM CHILEAN CALICHE

EPA Science Inventory

Paleogeochemical deposits in northern Chile are a rich source of naturally occurring sodium nitrate. These caliche ores are mined and processed to isolate NaNO3 (16-0-0) for use in fertilizers. Coincidentally, these very same deposits are a natural soure of perchlorate anion (C...

9 CFR 381.461 - Nutrient content claims for the sodium content.

Code of Federal Regulations, 2010 CFR

2010-01-01

... dehydrated products that must be reconstituted before typical consumption with water or a diluent containing... before typical consumption with water or a diluent containing an insignificant amount, as defined in... of sodium;” and (iii) If the product meets these conditions without the benefit of special processing...

Commercial scale cucumber fermentations brined with calcium chloride instead of sodium chloride

USDA-ARS?s Scientific Manuscript database

Development of low salt cucumber fermentation processes present opportunities to reduce the amount of sodium chloride (NaCl) that reaches fresh water streams from industrial activities. The objective of this research was to translate cucumber fermentation brined with calcium chloride instead of NaCl...

Precipitation-adsorption process for the decontamination of nuclear waste supernates

DOEpatents

Lee, Lien-Mow; Kilpatrick, Lester L.

1984-01-01

High-level nuclear waste supernate is decontaminated of cesium by precipitation of the cesium and potassium with sodium tetraphenyl boron. Simultaneously, strontium-90 is removed from the waste supernate sorption of insoluble sodium titanate. The waste solution is then filtered to separate the solution decontaminated of cesium and strontium.

Precipitation-adsorption process for the decontamination of nuclear waste supernates

DOEpatents

Lee, L.M.; Kilpatrick, L.L.

1982-05-19

High-level nuclear waste supernate is decontaminated of cesium by precipitation of the cesium and potassium with sodium tetraphenyl boron. Simultaneously, strontium-90 is removed from the waste supernate sorption of insoluble sodium titanate. The waste solution is then filtered to separate the solution decontaminated of cesium and strontium.

INTERIOR OF SHT (ROTARY DRYER FOR SODA) BUILDING OR DRYSIDE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

INTERIOR OF SHT (ROTARY DRYER FOR SODA) BUILDING OR DRYSIDE DRYERS WHICH REMOVED TRACES OF LIQUID FROM STD FILTRATE. HEAT CONVERTED SODIUM BICARBONATE TO SODIUM CARBONATE OR SODA ASH, THE PRINCIPAL PRODUCT OF THE WORKS. - Solvay Process Company, SHT Building, Between Willis & Milton Avenues, Solvay, Onondaga County, NY

Stakeholder discussion to reduce population-wide sodium intake and decrease sodium in the food supply: a conference report from the American Heart Association Sodium Conference 2013 Planning Group.

PubMed

Antman, Elliott M; Appel, Lawrence J; Balentine, Douglas; Johnson, Rachel K; Steffen, Lyn M; Miller, Emily Ann; Pappas, Antigoni; Stitzel, Kimberly F; Vafiadis, Dorothea K; Whitsel, Laurie

2014-06-24

A 2-day interactive forum was convened to discuss the current status and future implications of reducing sodium in the food supply and to identify opportunities for stakeholder collaboration. Participants included 128 stakeholders engaged in food research and development, food manufacturing and retail, restaurant and food service operations, regulatory and legislative activities, public health initiatives, healthcare, academia and scientific research, and data monitoring and surveillance. Presentation topics included scientific evidence for sodium reduction and public health policy recommendations; consumer sodium intakes, attitudes, and behaviors; food technologies and solutions for sodium reduction and sensory implications; experiences of the food and dining industries; and translation and implementation of sodium intake recommendations. Facilitated breakout sessions were conducted to allow for sharing of current practices, insights, and expertise. A well-established body of scientific research shows that there is a strong relationship between excess sodium intake and high blood pressure and other adverse health outcomes. With Americans getting >75% of their sodium from processed and restaurant food, this evidence creates mounting pressure for less sodium in the food supply. The reduction of sodium in the food supply is a complex issue that involves multiple stakeholders. The success of new technological approaches for reducing sodium will depend on product availability, health effects (both intended and unintended), research and development investments, quality and taste of reformulated foods, supply chain management, operational modifications, consumer acceptance, and cost. The conference facilitated an exchange of ideas and set the stage for potential collaboration opportunities among stakeholders with mutual interest in reducing sodium in the food supply and in Americans' diets. Population-wide sodium reduction remains a critically important component of public health efforts to promote cardiovascular health and prevent cardiovascular disease and will remain a priority for the American Heart Association. © 2014 American Heart Association, Inc.

Assessment of Korean consumer exposure to sodium saccharin, aspartame and stevioside.

PubMed

Ha, Mi-Sun; Ha, Sang-Do; Choi, Sung-Hee; Bae, Dong-Ho

2013-01-01

The dietary intakes of sodium saccharin, aspartame and stevioside were estimated on the basis of food consumption data of the Korean consumer and the concentration of sweeteners in processed foods. Results were compared with the acceptable daily intake (ADI) of sweeteners. Among the 28 food categories for which the application of sodium saccharin, aspartame and stevioside is permitted in Korea, they were detected in 5, 12 and 13 categories, respectively. The estimated daily intake (EDI) of sodium saccharin and aspartame were high in infants and children, whereas the EDI of stevioside was high in adolescents and adults. The most highly consumed sweetener was aspartame, and the highest EDI/ADI ratio was found for sodium saccharin. The main food categories contributing to sweetener consumption were beverages, including alcoholic beverages. For most Korean consumers, the EDIs were no greater than 20% of their corresponding ADI; however, the EDI of sodium saccharin for conservative consumers aged 1-2 years reached 60% of their ADI.

Aqueous rechargeable zinc/sodium vanadate batteries with enhanced performance from simultaneous insertion of dual carriers.

PubMed

Wan, Fang; Zhang, Linlin; Dai, Xi; Wang, Xinyu; Niu, Zhiqiang; Chen, Jun

2018-04-25

Rechargeable aqueous zinc-ion batteries are promising energy storage devices due to their high safety and low cost. However, they remain in their infancy because of the limited choice of positive electrodes with high capacity and satisfactory cycling performance. Furthermore, their energy storage mechanisms are not well established yet. Here we report a highly reversible zinc/sodium vanadate system, where sodium vanadate hydrate nanobelts serve as positive electrode and zinc sulfate aqueous solution with sodium sulfate additive is used as electrolyte. Different from conventional energy release/storage in zinc-ion batteries with only zinc-ion insertion/extraction, zinc/sodium vanadate hydrate batteries possess a simultaneous proton, and zinc-ion insertion/extraction process that is mainly responsible for their excellent performance, such as a high reversible capacity of 380 mAh g -1 and capacity retention of 82% over 1000 cycles. Moreover, the quasi-solid-state zinc/sodium vanadate hydrate battery is also a good candidate for flexible energy storage device.

[Sodium restriction during pregnancy: an outdated advice].

PubMed

de Leeuw, P W; Peeters, L L

1999-10-23

Even in an early phase of pregnancy marked haemodynamic changes occur, including a fall in vascular resistance and blood pressure and a rise in cardiac output. To compensate for the increased intravascular capacity the kidney retains more sodium and water. Apparently, the set point of sodium homeostasis shifts to a higher level at the expense of an expansion of extracellular volume. Studies during the normal menstrual cycle have shown that these changes, albeit smaller, also occur during the luteal phase. These fluctuations with the menstrual cycle are less apparent if salt intake is low, suggesting that a high salt intake is needed to facilitate the process of sodium retention. In pregnancies complicated by hypertension and/or pre-eclampsia body fluid volumes are low with an enhanced tendency to retain sodium after a volume challenge. These data, together with the lack of an apparent benefit of sodium restriction, suggest that the practice of prescribing a low-salt diet to hypertensive pregnant women should be abandoned.

Na(+) regulation by combined nitrogen in Azolla pinnata-Anabaena azollae symbiotic association during salt toxicity.

PubMed

Singh, Satya S; Singh, Santosh K; Mishra, Arun K

2008-01-01

To study the regulation of Na(+) ion by combined-N sources in Azolla pinnata-Anabaena azollae, Na(+) influx, intracellular Na(+) and Na(+) efflux were investigated in the presence of different N-sources (N(2), NH(4)(+), NO(3)(-) and urea) and various NaCl concentrations. Sodium influx by Azolla pinnata fronds was minimum in the presence of NO(3)(-). Almost identical levels of intracellular sodium, although less than N(2) and NH(4)(+) incubated fronds were observed in the presence of NO(3)(-) and urea. Efflux of sodium was minimum in urea and NO(3)(-) grown fronds. A low residual sodium was observed in the fronds incubated in NO(3)(-) and urea supplemented media. Results suggest that nitrate and urea curtailed the entry of sodium, reduced salt toxicity maximally by maintaining the minimum level of sodium and also conserved energy due to slow influx and efflux of Na(+) within the fronds during salt shock and the process of adaptation.

A stable room-temperature sodium-sulfur battery.

PubMed

Wei, Shuya; Xu, Shaomao; Agrawral, Akanksha; Choudhury, Snehashis; Lu, Yingying; Tu, Zhengyuan; Ma, Lin; Archer, Lynden A

2016-06-09

High-energy rechargeable batteries based on earth-abundant materials are important for mobile and stationary storage technologies. Rechargeable sodium-sulfur batteries able to operate stably at room temperature are among the most sought-after platforms because such cells take advantage of a two-electron-redox process to achieve high storage capacity from inexpensive electrode materials. Here we report a room-temperature sodium-sulfur battery that uses a microporous carbon-sulfur composite cathode, and a liquid carbonate electrolyte containing the ionic liquid 1-methyl-3-propylimidazolium-chlorate tethered to SiO2 nanoparticles. We show that these cells can cycle stably at a rate of 0.5 C (1 C=1675, mAh g(-1)) with 600 mAh g(-1) reversible capacity and nearly 100% Coulombic efficiency. By means of spectroscopic and electrochemical analysis, we find that the particles form a sodium-ion conductive film on the anode, which stabilizes deposition of sodium. We also find that sulfur remains interred in the carbon pores and undergo solid-state electrochemical reactions with sodium ions.

Associating cooking additives with sodium hydroxide to pretreat bamboo residues for improving the enzymatic saccharification and monosaccharides production.

PubMed

Huang, Caoxing; He, Juan; Wang, Yan; Min, Douyong; Yong, Qiang

2015-10-01

Cooking additive pulping technique is used in kraft mill to increase delignification degree and pulp yield. In this work, cooking additives were firstly applied in the sodium hydroxide pretreatment for improving the bioconversion of bamboo residues to monosaccharides. Meanwhile, steam explosion and sulfuric acid pretreatments were also carried out on the sample to compare their impacts on monosaccharides production. Results indicated that associating anthraquinone with sodium hydroxide pretreatment showed the best performance in improving the original carbohydrates recovery, delignification, enzymatic saccharification, and monosaccharides production. After consecutive pretreatment and enzymatic saccharification process, 347.49 g, 307.48 g, 142.93 g, and 87.15 g of monosaccharides were released from 1000 g dry bamboo residues pretreated by sodium hydroxide associating with anthraquinone, sodium hydroxide, steam explosion and sulfuric acid, respectively. The results suggested that associating cooking additive with sodium hydroxide is an effective pretreatment for bamboo residues to enhance enzymatic saccharification for monosaccharides production. Copyright © 2015 Elsevier Ltd. All rights reserved.

METHOD OF PROCESSING MONAZITE SAND

DOEpatents

Calkins, G.D.

1957-10-29

A method is given for the pretreatment of monazite sand with sodium hydroxide. When momazite sand is reacted with sodium hydroxide, the thorium, uranium, and rare earths are converted to water-insoluble hydrous oxides; but in the case of uranium, the precipitate compound may at least partly consist of a slightly soluble uranate. According to the patent, monazite sand is treated with an excess of aqueous sodium hydroxide solution, and the insoluble compounds of thorium, uranium, and the rare earths are separated from the aqueous solution. This solution is then concentrated causing sodium phosphate to crystallize out. The crystals are removed from the remaining solution, and the solution is recycled for reaction with a mew supply of momazite sand.

Mercury Sodium Tail

NASA Image and Video Library

2015-04-16

This image from NASA MESSENGER spacecraft is stitched together from thousands of observations made over the past 4 years by the MASCS/UVVS instrument, which measures sunlight scattered off of Mercury tenuous atmosphere. Scattered sunlight gives the sodium a bright orange glow. This scattering process also gives sodium atoms a push - this "radiation pressure" is strong enough, during parts of Mercury's year, to strip the atmosphere and give Mercury a long glowing tail. Someone standing on Mercury's nightside at the right time of year would see a faint orange similar to a city sky illuminated by sodium lamps! Instrument: Mercury Atmospheric and Surface Composition Spectrometer (MASCS)/Ultraviolet and Visible Spectrometer (UVVS) http://photojournal.jpl.nasa.gov/catalog/PIA19418

Development of a process for high capacity arc heater production of silicon for solar arrays

NASA Technical Reports Server (NTRS)

Meyer, T. N.

1980-01-01

A high temperature silicon production process using existing electric arc heater technology is discussed. Silicon tetrachloride and a reductant, liquid sodium, were injected into an arc heated mixture of hydrogen and argon. Under these high temperature conditions, a very rapid reaction occurred, yielding silicon and gaseous sodium chloride. Techniques for high temperature separation and collection of the molten silicon were developed. The desired degree of separation was not achieved. The electrical, control and instrumentation, cooling water, gas, SiCl4, and sodium systems are discussed. The plasma reactor, silicon collection, effluent disposal, the gas burnoff stack, and decontamination and safety are also discussed. Procedure manuals, shakedown testing, data acquisition and analysis, product characterization, disassembly and decontamination, and component evaluation are reviewed.

Comparison of amine-selective properties of weak and strong cation-exchangers.

PubMed

Stenholm, Ake; Lindgren, Helena; Shaffie, Juliana

2006-09-22

The capacity of several weak and strong cation-exchangers to adsorb 2-diethylaminoethanol (DEAE) and (2,3-hydroxypropyl) trimethylammonium chloride (HPMAC) from sodium-containing process water streams, and the ease of subsequently eluting the amines and regenerating the exchangers, were investigated. (2,3-hydroxypropyl) trimethylammonium chloride was enriched 40-fold compared with the initial amine/sodium-ratio in the bulk fluid by Amberlite IRC-50. The highest selectivity for 2-diethylaminoethanol (26-fold) was provided by Imac HP336. Neither of the selected strong cation-exchangers showed any selectivity towards 2-diethylaminoethanol, but they enriched (2,3-hydroxypropyl) trimethylammonium chloride approximately three to four fold. These findings suggest that weak cation-exchangers (WCX) could be readily used for the selective removal of these or similar amines from sodium-containing process waters.

β-NaVOPO 4 obtained by a low-temperature synthesis process: A new 3.3 V cathode for sodium-ion batteries

DOE PAGES

He, Guang; Huq, Ashfia; Manthiram, Arumugam; ...

2016-02-02

Vanadyl phosphates (VOPO 4) represent a class of attractive cathodes in lithium-ion batteries. However, the exploration of this type of materials in sodium-ion batteries is rare. Here, we report for the first time the synthesis of orthorhombic β-NaVOPO 4 by first chemically extracting lithium from beta-LiVOPO 4 and then inserting sodium into the obtained β-VOPO 4 by a microwave-assisted solvothermal process with NaI, which serves both as a reducing agent and sodium source. Intermediate Na xVOPO 4 compositions with x = 0.3, 0.5, and 0.8 have also been obtained by controlling the amount of NaI in the reaction mixture. Jointmore » Rietveld refinement of synchrotron X-ray diffraction (XRD) and neutron diffraction confirms that the fully sodiated β-NaVOPO 4 is isostructural with the lithium counterpart β-LiVOPO 4. Bond valence sum maps suggest that sodium ions possibly diffuse along the [010] direction in the lattice, similar to the ionic conduction pathway in β-LiVOPO 4. Although the initial discharge capacity is low due to the protons in the structure, it steadily increases with cycling with a long plateau at 3.3 V. As a result, ex situ XRD data of cycled β-VOPO 4 and β-NaVOPO 4 electrodes confirm the reversible reaction in sodium cells involving the V 4+/V 5+ redox couple.« less

Chemistry and Mechanism of Interaction Between Molybdenite Concentrate and Sodium Chloride When Heated in the Presence of Oxygen

NASA Astrophysics Data System (ADS)

Aleksandrov, P. V.; Medvedev, A. S.; Imideev, V. A.; Moskovskikh, D. O.

2017-04-01

Roasting of molybdenum concentrates with sodium chloride has high potential and can be an alternative to oxidizing roasting and autoclave leaching; however, the chemistry and mechanism are poorly known. The chemical mechanism of the roasting process between molybdenite concentrate and sodium chloride in the presence of atmospheric oxygen is proposed. It is demonstrated that the process occurs through molybdenite oxidation, up to molybdenum trioxide, with subsequent formation of sodium polymolybdates and molybdenum dioxydichloride from molybdenum trioxide. It is found that the formation of water-soluble sodium polymolybdates from molybdenum trioxide stops over time due to passivation of sodium chloride surface by polymolybdates. It is proved experimentally that preliminary grinding of the mixture in a furnace charge leads to an increase in the polymolybdate fraction of the roasting products, which constitutes approximately 65 pct of molybdenum initially in the roasted mixture against 20 to 22 pct in a nonground mixture (or 75 to 77 pct against 30 to 33 pct of molybdenum in calcine). For the first time, the presence of the Na2S2O7 phase in the calcine was confirmed experimentally. The suggested mechanism gives possible explanations for the sharp increase of MoO2Cl2 formation within the temperature range of 673 K to 723 K (400 °C to 450 °C) that is based on the catalytic reaction of molybdenum dioxydichloride from the Na2S2O7 liquid phase as it runs in a melt.

Simulant Development for LAWPS Testing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Russell, Renee L.; Schonewill, Philip P.; Burns, Carolyn A.

2017-05-23

This report describes simulant development work that was conducted to support the technology maturation of the LAWPS facility. Desired simulant physical properties (density, viscosity, solids concentration, solid particle size), sodium concentrations, and general anion identifications were provided by WRPS. The simulant recipes, particularly a “nominal” 5.6M Na simulant, are intended to be tested at several scales, ranging from bench-scale (500 mL) to full-scale. Each simulant formulation was selected to be chemically representative of the waste streams anticipated to be fed to the LAWPS system, and used the current version of the LAWPS waste specification as a formulation basis. After simulantmore » development iterations, four simulants of varying sodium concentration (5.6M, 6.0M, 4.0M, and 8.0M) were prepared and characterized. The formulation basis, development testing, and final simulant recipes and characterization data for these four simulants are presented in this report.« less

Hierarchical TiO2/C micro-nano spheres as high-performance anode materials for sodium ion batteries

NASA Astrophysics Data System (ADS)

Ma, Xiao; Zhang, Zhihui; Tian, Jianliya; Xu, Beibei; Ping, Qiushi; Wang, Baofeng

The hierarchical TiO2/C microspheres were obtained via a facile method of in-situ hydrolysis and spray drying. Antase TiO2 nanoparticles were coherent to microspheres TiO2/C due to the pyrolysis of carbon source (PVP). Besides, the favorable electron transfer from carbon to TiO2 improves the electronic conductivity of TiO2 via the presence of Ti-C bond within TiO2/C composite. Charge-discharge tests show that TiO2/C microspheres delivered a good rate capability of 106.1mAhg‑1 at the high current density of 5Ag‑1 and an enhanced cyclic capacity. The superior electrochemical performance could be ascribed to the porous micro-nano structure, smaller crystal size and increased conductivity. The synthesis of TiO2/C microspheres is easy to scale up for satisfying high-performance sodium storage.

A nano-bio interfacial protein corona on silica nanoparticle.

PubMed

Zhang, Hongyan; Peng, Jiaxi; Li, Xin; Liu, Shengju; Hu, Zhengyan; Xu, Guiju; Wu, Ren'an

2018-07-01

Nano-bio interaction takes the crucial role in bio-application of nanoparticles. The systematic mapping of interfacial proteins remains the big challenge as low level of proteins within interface regions and lack of appropriate technology. Here, a facile proteomic strategy was developed to characterize the interfacial protein corona (noted as IPC) that has strong interactions with silica nanoparticle, via the combination of the vigorous elution with high concentration sodium dodecyl sulfate (SDS) and the pre-isolation of sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE). The trace level IPCs for silica nanoparticle were thus qualitatively and quantitatively identified. Bioinformatics analyses revealed the intrinsic compositions, relevance and potential regularity addressing the strong interactions between IPC and nanoparticle. This strategy in determining IPCs is opening an avenue to give a deep insight to understand the interaction between proteins and not only nanoparticles but also other bulk materials. Copyright © 2018 Elsevier B.V. All rights reserved.

A facile solvothermal method to produce graphene-ZnS composites for superior photoelectric applications

NASA Astrophysics Data System (ADS)

Lei, Yun; Chen, Feifei; Li, Rong; Xu, Jun

2014-07-01

In this experiment, flake graphite (<30 μm) was prepared as raw materials. Graphite oxide is prepared with Hummers method by low temperature, middle temperature and high temperature, and further treated with super-sonic oscillation to get graphene oxide. Graphene-zinc sulfide composites were synthesized through a simple solvothermal method using thiourea or sodium sulfide as sulfur source in the ethylene glycol or ethylenediamine, respectively. The products were characterized by X-ray and SEM, and analyzed by the transient photocurrent response and electrochemical impedance spectra. The results indicate that the properties of graphene-zinc sulfide composites prepared with thiourea in ethylene glycol are superior to those of blank-ZnS and composites prepared with sodium sulfide and ethylenediamine, which is attributed to electron capture and transfer ability of graphene resulting in a more efficient separation of the photoexcited charge carriers from ZnS-graphene composites.

ARGOS - the Laser Star Adaptive Optics for LBT

NASA Astrophysics Data System (ADS)

Rabien, S.; Barl, L.; Beckmann, U.; Blümchen, T.; Bonaglia, M.; Borelli, J. L.; Brynnel, J.; Busoni, L.; Carbonaro, L.; Conot, C.; Davies, R.; Deysenroth, M.; Durney, O.; Elberich, M.; Esposito, S.; Gasho, V.; Gässler, W.; Gemperlein, H.; Genzel, R.; Green, R.; Haug, M.; Lloyd Hart, M.; Hubbard, P.; Kanneganti, S.; Kulas, M.; Noenickx, J.; Peter, D.; Quirrenbach, A.; Rademacher, M.; Rix, H. W.; Salinari, P.; Schwab, C.; Storm, J.; Strüder, L.; Thiel, M.; Weigelt, G.; Ziegleder, J.; Orban de Xivry, G.

2011-09-01

We will present the design and status of ARGOS - the Laser Guide Star adaptive optics facility for the Large Binocular Telescope. By projecting a constellation of multiple laser guide stars above each of the 8.4m primary mirrors of the LBT, ARGOS in its ground layer mode will enable a wide field adaptive optics correction for multi object spectroscopy. ARGOS implements high power pulsed green lasers and makes use of Rayleigh scattering for the guide star creation. The geometric relations of this setup in guide star height vs. primary diameter are quite comparable to an ELT with sodium guide stars. The use of LBT's adaptive secondary mirror, gated wavefront sensors, a prime focus calibration system and the laser constellation shows several aspects that may be used as pathfinding technology for the planned ELTs. In already planned upgrade steps with a hybrid Sodium-Rayleigh combination ARGOS will enable MCAO and MOAO implementations at LBT allowing unique astronomical observations.