Space shuttle entry and landing navigation analysis

NASA Technical Reports Server (NTRS)

Jones, H. L.; Crawford, B. S.

1974-01-01

A navigation system for the entry phase of a Space Shuttle mission which is an aided-inertial system which uses a Kalman filter to mix IMU data with data derived from external navigation aids is evaluated. A drag pseudo-measurement used during radio blackout is treated as an additional external aid. A comprehensive truth model with 101 states is formulated and used to generate detailed error budgets at several significant time points -- end-of-blackout, start of final approach, over runway threshold, and touchdown. Sensitivity curves illustrating the effect of variations in the size of individual error sources on navigation accuracy are presented. The sensitivity of the navigation system performance to filter modifications is analyzed. The projected overall performance is shown in the form of time histories of position and velocity error components. The detailed results are summarized and interpreted, and suggestions are made concerning possible software improvements.

Software life cycle methodologies and environments

NASA Technical Reports Server (NTRS)

Fridge, Ernest

1991-01-01

Products of this project will significantly improve the quality and productivity of Space Station Freedom Program software processes by: improving software reliability and safety; and broadening the range of problems that can be solved with computational solutions. Projects brings in Computer Aided Software Engineering (CASE) technology for: Environments such as Engineering Script Language/Parts Composition System (ESL/PCS) application generator, Intelligent User Interface for cost avoidance in setting up operational computer runs, Framework programmable platform for defining process and software development work flow control, Process for bringing CASE technology into an organization's culture, and CLIPS/CLIPS Ada language for developing expert systems; and methodologies such as Method for developing fault tolerant, distributed systems and a method for developing systems for common sense reasoning and for solving expert systems problems when only approximate truths are known.

Trends in Facility Management Technology: The Emergence of the Internet, GIS, and Facility Assessment Decision Support.

ERIC Educational Resources Information Center

Teicholz, Eric

1997-01-01

Reports research on trends in computer-aided facilities management using the Internet and geographic information system (GIS) technology for space utilization research. Proposes that facility assessment software holds promise for supporting facility management decision making, and outlines four areas for its use: inventory; evaluation; reporting;…

Effect of cement space on the marginal fit of CAD-CAM-fabricated monolithic zirconia crowns.

PubMed

Kale, Ediz; Seker, Emre; Yilmaz, Burak; Özcelik, Tuncer Burak

2016-12-01

Monolithic zirconia crowns fabricated with computer-aided design and computer-aided manufacturing (CAD-CAM) have recently become a common practice for the restoration of posterior teeth. The marginal fit of monolithic zirconia crowns may be affected by different cement space parameters set in the CAD software. Information is scarce regarding the effect of cement space on the marginal fit of monolithic zirconia crowns fabricated with CAD-CAM technology. The purpose of this in vitro study was to evaluate the effect of cement space on the marginal fit of CAD-CAM-fabricated monolithic zirconia crowns before cementation. Fifteen right maxillary first molar typodont teeth with standardized anatomic preparations for complete-coverage ceramic crowns were scanned with a 3-dimensional laboratory scanner. Crowns were designed 3-dimensionally using software and then milled from presintered monolithic zirconia blocks in a computer numerical control dental milling machine. The cement space was set at 25 μm around the margins for all groups, and additional cement space starting 1 mm above the finish lines of the teeth was set at 30 μm for group 25-30, 40 μm for group 25-40, and 50 μm for group 25-50 in the CAD software. A total of 120 images (3 groups, 5 crowns per group, 8 sites per crown) were measured for vertical marginal discrepancy under a stereoscopic zoom microscope and the data were statistically analyzed with 1-way analysis of variance, followed by the Tukey honestly significant difference test (α=.05). The results showed that different cement space values had statistically significant effect on the mean vertical marginal discrepancy value of tested crowns (P<.001). The mean marginal discrepancy was 85 μm for group 25-30, 68 μm for group 25-40, and 53 μm for group 25-50. Within the limitations of this in vitro study, it was concluded that the cement space had a significant effect on the marginal fit of CAD-CAM-fabricated monolithic zirconia crowns. The marginal fit improved as the cement space decreased. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Computer science: Key to a space program renaissance. The 1981 NASA/ASEE summer study on the use of computer science and technology in NASA. Volume 2: Appendices

NASA Technical Reports Server (NTRS)

Freitas, R. A., Jr. (Editor); Carlson, P. A. (Editor)

1983-01-01

Adoption of an aggressive computer science research and technology program within NASA will: (1) enable new mission capabilities such as autonomous spacecraft, reliability and self-repair, and low-bandwidth intelligent Earth sensing; (2) lower manpower requirements, especially in the areas of Space Shuttle operations, by making fuller use of control center automation, technical support, and internal utilization of state-of-the-art computer techniques; (3) reduce project costs via improved software verification, software engineering, enhanced scientist/engineer productivity, and increased managerial effectiveness; and (4) significantly improve internal operations within NASA with electronic mail, managerial computer aids, an automated bureaucracy and uniform program operating plans.

Situation Awareness of Onboard System Autonomy

NASA Technical Reports Server (NTRS)

Schreckenghost, Debra; Thronesbery, Carroll; Hudson, Mary Beth

2005-01-01

We have developed intelligent agent software for onboard system autonomy. Our approach is to provide control agents that automate crew and vehicle systems, and operations assistants that aid humans in working with these autonomous systems. We use the 3 Tier control architecture to develop the control agent software that automates system reconfiguration and routine fault management. We use the Distributed Collaboration and Interaction (DCI) System to develop the operations assistants that provide human services, including situation summarization, event notification, activity management, and support for manual commanding of autonomous system. In this paper we describe how the operations assistants aid situation awareness of the autonomous control agents. We also describe our evaluation of the DCI System to support control engineers during a ground test at Johnson Space Center (JSC) of the Post Processing System (PPS) for regenerative water recovery.

On public space design for Chinese urban residential area based on integrated architectural physics environment evaluation

NASA Astrophysics Data System (ADS)

Dong, J. Y.; Cheng, W.; Ma, C. P.; Tan, Y. T.; Xin, L. S.

2017-04-01

The residential public space is an important part in designing the ecological residence, and a proper physics environment of public space is of greater significance to urban residence in China. Actually, the measure to apply computer aided design software into residential design can effectively avoid an inconformity of design intent with actual using condition, and a negative impact on users due to bad architectural physics environment of buildings, etc. The paper largely adopts a design method of analyzing architectural physics environment of residential public space. By analyzing and evaluating various physics environments, a suitability assessment is obtained for residential public space, thereby guiding the space design.

Error-Free Software

NASA Technical Reports Server (NTRS)

1989-01-01

001 is an integrated tool suited for automatically developing ultra reliable models, simulations and software systems. Developed and marketed by Hamilton Technologies, Inc. (HTI), it has been applied in engineering, manufacturing, banking and software tools development. The software provides the ability to simplify the complex. A system developed with 001 can be a prototype or fully developed with production quality code. It is free of interface errors, consistent, logically complete and has no data or control flow errors. Systems can be designed, developed and maintained with maximum productivity. Margaret Hamilton, President of Hamilton Technologies, also directed the research and development of USE.IT, an earlier product which was the first computer aided software engineering product in the industry to concentrate on automatically supporting the development of an ultrareliable system throughout its life cycle. Both products originated in NASA technology developed under a Johnson Space Center contract.

TOOTHPASTEV6.11.3

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sankel, David J.; Clair, Aaron B. St.; Langsfield, Joshua D.

2006-11-01

Toothpaste is a graphical user interface and Computer Aided Drafting/Manufacturing (CAD/CAM) software package used to plan tool paths for Galil Motion Control hardware. The software is a tool for computer controlled dispensing of materials. The software may be used for solid freeform fabrication of components or the precision printing of inks. Mathematical calculations are used to produce a set of segments and arcs that when coupled together will fill space. The paths of the segments and arcs are then translated into a machine language that controls the motion of motors and translational stages to produce tool paths in three dimensions.more » As motion begins material(s) are dispensed or printed along the three-dimensional pathway.« less

A Data-Driven Solution for Performance Improvement

NASA Technical Reports Server (NTRS)

2002-01-01

Marketed as the "Software of the Future," Optimal Engineering Systems P.I. EXPERT(TM) technology offers statistical process control and optimization techniques that are critical to businesses looking to restructure or accelerate operations in order to gain a competitive edge. Kennedy Space Center granted Optimal Engineering Systems the funding and aid necessary to develop a prototype of the process monitoring and improvement software. Completion of this prototype demonstrated that it was possible to integrate traditional statistical quality assurance tools with robust optimization techniques in a user- friendly format that is visually compelling. Using an expert system knowledge base, the software allows the user to determine objectives, capture constraints and out-of-control processes, predict results, and compute optimal process settings.

Software/hardware distributed processing network supporting the Ada environment

NASA Astrophysics Data System (ADS)

Wood, Richard J.; Pryk, Zen

1993-09-01

A high-performance, fault-tolerant, distributed network has been developed, tested, and demonstrated. The network is based on the MIPS Computer Systems, Inc. R3000 Risc for processing, VHSIC ASICs for high speed, reliable, inter-node communications and compatible commercial memory and I/O boards. The network is an evolution of the Advanced Onboard Signal Processor (AOSP) architecture. It supports Ada application software with an Ada- implemented operating system. A six-node implementation (capable of expansion up to 256 nodes) of the RISC multiprocessor architecture provides 120 MIPS of scalar throughput, 96 Mbytes of RAM and 24 Mbytes of non-volatile memory. The network provides for all ground processing applications, has merit for space-qualified RISC-based network, and interfaces to advanced Computer Aided Software Engineering (CASE) tools for application software development.

Automated Software Development Workstation (ASDW)

NASA Technical Reports Server (NTRS)

Fridge, Ernie

1990-01-01

Software development is a serious bottleneck in the construction of complex automated systems. An increase of the reuse of software designs and components has been viewed as a way to relieve this bottleneck. One approach to achieving software reusability is through the development and use of software parts composition systems. A software parts composition system is a software development environment comprised of a parts description language for modeling parts and their interfaces, a catalog of existing parts, a composition editor that aids a user in the specification of a new application from existing parts, and a code generator that takes a specification and generates an implementation of a new application in a target language. The Automated Software Development Workstation (ASDW) is an expert system shell that provides the capabilities required to develop and manipulate these software parts composition systems. The ASDW is now in Beta testing at the Johnson Space Center. Future work centers on responding to user feedback for capability and usability enhancement, expanding the scope of the software lifecycle that is covered, and in providing solutions to handling very large libraries of reusable components.

Exploratory research for the development of a computer aided software design environment with the software technology program

NASA Technical Reports Server (NTRS)

Hardwick, Charles

1991-01-01

Field studies were conducted by MCC to determine areas of research of mutual interest to MCC and JSC. NASA personnel from the Information Systems Directorate and research faculty from UHCL/RICIS visited MCC in Austin, Texas to examine tools and applications under development in the MCC Software Technology Program. MCC personnel presented workshops in hypermedia, design knowledge capture, and design recovery on site at JSC for ISD personnel. The following programs were installed on workstations in the Software Technology Lab, NASA/JSC: (1) GERM (Graphic Entity Relations Modeler); (2) gIBIS (Graphic Issues Based Information System); and (3) DESIRE (Design Recovery tool). These applications were made available to NASA for inspection and evaluation. Programs developed in the MCC Software Technology Program run on the SUN workstation. The programs do not require special configuration, but they will require larger than usual amounts of disk space and RAM to operate properly.

Design analysis and computer-aided performance evaluation of shuttle orbiter electrical power system. Volume 1: Summary

NASA Technical Reports Server (NTRS)

1974-01-01

Studies were conducted to develop appropriate space shuttle electrical power distribution and control (EPDC) subsystem simulation models and to apply the computer simulations to systems analysis of the EPDC. A previously developed software program (SYSTID) was adapted for this purpose. The following objectives were attained: (1) significant enhancement of the SYSTID time domain simulation software, (2) generation of functionally useful shuttle EPDC element models, and (3) illustrative simulation results in the analysis of EPDC performance, under the conditions of fault, current pulse injection due to lightning, and circuit protection sizing and reaction times.

Object oriented fault diagnosis system for space shuttle main engine redlines

NASA Technical Reports Server (NTRS)

Rogers, John S.; Mohapatra, Saroj Kumar

1990-01-01

A great deal of attention has recently been given to Artificial Intelligence research in the area of computer aided diagnostics. Due to the dynamic and complex nature of space shuttle red-line parameters, a research effort is under way to develop a real time diagnostic tool that will employ historical and engineering rulebases as well as a sensor validity checking. The capability of AI software development tools (KEE and G2) will be explored by applying object oriented programming techniques in accomplishing the diagnostic evaluation.

Large Advanced Space Systems (LASS) computer-aided design program additions

NASA Technical Reports Server (NTRS)

Farrell, C. E.

1982-01-01

The LSS preliminary and conceptual design requires extensive iteractive analysis because of the effects of structural, thermal, and control intercoupling. A computer aided design program that will permit integrating and interfacing of required large space system (LSS) analyses is discussed. The primary objective of this program is the implementation of modeling techniques and analysis algorithms that permit interactive design and tradeoff studies of LSS concepts. Eight software modules were added to the program. The existing rigid body controls module was modified to include solar pressure effects. The new model generator modules and appendage synthesizer module are integrated (interfaced) to permit interactive definition and generation of LSS concepts. The mass properties module permits interactive specification of discrete masses and their locations. The other modules permit interactive analysis of orbital transfer requirements, antenna primary beam n, and attitude control requirements.

Space Telecommunications Radio System (STRS) Compliance Testing

NASA Technical Reports Server (NTRS)

Handler, Louis M.

2011-01-01

The Space Telecommunications Radio System (STRS) defines an open architecture for software defined radios. This document describes the testing methodology to aid in determining the degree of compliance to the STRS architecture. Non-compliances are reported to the software and hardware developers as well as the NASA project manager so that any non-compliances may be fixed or waivers issued. Since the software developers may be divided into those that provide the operating environment including the operating system and STRS infrastructure (OE) and those that supply the waveform applications, the tests are divided accordingly. The static tests are also divided by the availability of an automated tool that determines whether the source code and configuration files contain the appropriate items. Thus, there are six separate step-by-step test procedures described as well as the corresponding requirements that they test. The six types of STRS compliance tests are: STRS application automated testing, STRS infrastructure automated testing, STRS infrastructure testing by compiling WFCCN with the infrastructure, STRS configuration file testing, STRS application manual code testing, and STRS infrastructure manual code testing. Examples of the input and output of the scripts are shown in the appendices as well as more specific information about what to configure and test in WFCCN for non-compliance. In addition, each STRS requirement is listed and the type of testing briefly described. Attached is also a set of guidelines on what to look for in addition to the requirements to aid in the document review process.

Linda Finch speaks to children during World Flight in New Orleans, La.

NASA Technical Reports Server (NTRS)

1997-01-01

Linda Finch, who re-created the flight of Amelia Earhardt's flight around the world 60 years ago, landed at New Orleans Lakefront Airport to speak to groups of inner-city school children during World Flight 1997. Stennis Space Center's Educator Resource Center played a role in the event by providing SSC-developed Geomap software to aid students in tracking Finch's flight.

Expert system verification concerns in an operations environment

NASA Technical Reports Server (NTRS)

Goodwin, Mary Ann; Robertson, Charles C.

1987-01-01

The Space Shuttle community is currently developing a number of knowledge-based tools, primarily expert systems, to support Space Shuttle operations. It is proposed that anticipating and responding to the requirements of the operations environment will contribute to a rapid and smooth transition of expert systems from development to operations, and that the requirements for verification are critical to this transition. The paper identifies the requirements of expert systems to be used for flight planning and support and compares them to those of existing procedural software used for flight planning and support. It then explores software engineering concepts and methodology that can be used to satisfy these requirements, to aid the transition from development to operations and to support the operations environment during the lifetime of expert systems. Many of these are similar to those used for procedural hardware.

KSC-2012-2891

NASA Image and Video Library

2011-07-20

LOUISVILLE, Colo. – During NASA's Commercial Crew Development Round 2 CCDev2) activities for the Commercial Crew Program CCP, Sierra Nevada Corp. SNC built a Simulator and Avionics Laboratory to help engineers evaluate the Dream Chaser's characteristics during the piloted phases of flight. Located at Sierra Nevada’s Space Systems facility in Louisville, Colo., it consists of a physical cockpit and integrated simulation hardware and software. The simulator is linked to the Vehicle Avionics Integration Laboratory, or VAIL, which serves as a platform for Dream Chaser avionics development, engineering testing and integration. VAIL also will also be used for verification and validation of avionics and software. Sierra Nevada is one of seven companies NASA entered into Space Act Agreements SAAs with during CCDev2 to aid in the innovation and development of American-led commercial capabilities for crew transportation and rescue services to and from the International Space Station and other low Earth orbit destinations. For information about CCP, visit www.nasa.gov/commercialcrew. Photo credit: Sierra Nevada Corp.

A Structure for Creating Quality Software.

ERIC Educational Resources Information Center

Christensen, Larry C.; Bodey, Michael R.

1990-01-01

Addresses the issue of assuring quality software for use in computer-aided instruction and presents a structure by which developers can create quality courseware. Differences between courseware and computer-aided instruction software are discussed, methods for testing software are described, and human factors issues as well as instructional design…

Software Library: A Reusable Software Issue.

DTIC Science & Technology

1984-06-01

On reverse aide it neceeary aid Identify by block number) Software Library; Program Library; Reusability; Generator 20 ABSTRACT (Cmlnue on revere... Software Library. A particular example of the Software Library, the Program Library, is described as a prototype of a reusable library. A hierarchical... programming libraries are described. Finally, non code products in the Software Library are discussed. Accesson Fo NTIS R~jS DrrC TA Availability Codes 0

Dypas: A dynamic payload scheduler for shuttle missions

NASA Technical Reports Server (NTRS)

Davis, Stephen

1988-01-01

Decision and analysis systems have had broad and very practical application areas in the human decision making process. These software systems range from the help sections in simple accounting packages, to the more complex computer configuration programs. Dypas is a decision and analysis system that aids prelaunch shutlle scheduling, and has added functionality to aid the rescheduling done in flight. Dypas is written in Common Lisp on a Symbolics Lisp machine. Dypas differs from other scheduling programs in that it can draw its knowledge from different rule bases and apply them to different rule interpretation schemes. The system has been coded with Flavors, an object oriented extension to Common Lisp on the Symbolics hardware. This allows implementation of objects (experiments) to better match the problem definition, and allows a more coherent solution space to be developed. Dypas was originally developed to test a programmer's aptitude toward Common Lisp and the Symbolics software environment. Since then the system has grown into a large software effort with several programmers and researchers thrown into the effort. Dypas is currently using two expert systems and three inferencing procedures to generate a many object schedule. The paper will review the abilities of Dypas and comment on its functionality.

The shuttle main engine: A first look

NASA Technical Reports Server (NTRS)

Schreur, Barbara

1996-01-01

Anyone entering the Space Shuttle Main Engine (SSME) team attends a two week course to become familiar with the design and workings of the engine. This course provides intensive coverage of the individual hardware items and their functions. Some individuals, particularly those involved with software maintenance and development, have felt overwhelmed by this volume of material and their lack of a logical framework in which to place it. To provide this logical framework, it was decided that a brief self-taught introduction to the overall operation of the SSME should be designed. To aid the people or new team members with an interest in the software, this new course should also explain the structure and functioning of the controller and its software. This paper presents a description of this presentation.

Experience report: Using formal methods for requirements analysis of critical spacecraft software

NASA Technical Reports Server (NTRS)

Lutz, Robyn R.; Ampo, Yoko

1994-01-01

Formal specification and analysis of requirements continues to gain support as a method for producing more reliable software. However, the introduction of formal methods to a large software project is difficult, due in part to the unfamiliarity of the specification languages and the lack of graphics. This paper reports results of an investigation into the effectiveness of formal methods as an aid to the requirements analysis of critical, system-level fault-protection software on a spacecraft currently under development. Our experience indicates that formal specification and analysis can enhance the accuracy of the requirements and add assurance prior to design development in this domain. The work described here is part of a larger, NASA-funded research project whose purpose is to use formal-methods techniques to improve the quality of software in space applications. The demonstration project described here is part of the effort to evaluate experimentally the effectiveness of supplementing traditional engineering approaches to requirements specification with the more rigorous specification and analysis available with formal methods.

The space science data service: A study of its efficiencies and costs

NASA Technical Reports Server (NTRS)

Vette, J. I.; Hilberg, R. H.; Zuhl, D. E.; West, A. E.

1979-01-01

Factors affecting the overall advantages and disadvantages of a centralized facility for both the data base and processing capability for NASA's Office of Space Science programs are examined in an effort to determine the best approach to data management in the light of the increasing number of data bits collected annually. Selected issues considered relate to software and storage savings, security precautions, and the phase-in plan. Information on the current mode of processing and on the potential impact of changes resulting from a conversion to a space science data base service was obtained from five user groups and is presented as an aid in determining the dollar benefits and advantages of a centralized system.

Proceedings of the 1993 Conference on Intelligent Computer-Aided Training and Virtual Environment Technology, Volume 1

NASA Technical Reports Server (NTRS)

Hyde, Patricia R.; Loftin, R. Bowen

1993-01-01

These proceedings are organized in the same manner as the conference's contributed sessions, with the papers grouped by topic area. These areas are as follows: VE (virtual environment) training for Space Flight, Virtual Environment Hardware, Knowledge Aquisition for ICAT (Intelligent Computer-Aided Training) & VE, Multimedia in ICAT Systems, VE in Training & Education (1 & 2), Virtual Environment Software (1 & 2), Models in ICAT systems, ICAT Commercial Applications, ICAT Architectures & Authoring Systems, ICAT Education & Medical Applications, Assessing VE for Training, VE & Human Systems (1 & 2), ICAT Theory & Natural Language, ICAT Applications in the Military, VE Applications in Engineering, Knowledge Acquisition for ICAT, and ICAT Applications in Aerospace.

Space station advanced automation

NASA Technical Reports Server (NTRS)

Woods, Donald

1990-01-01

In the development of a safe, productive and maintainable space station, Automation and Robotics (A and R) has been identified as an enabling technology which will allow efficient operation at a reasonable cost. The Space Station Freedom's (SSF) systems are very complex, and interdependent. The usage of Advanced Automation (AA) will help restructure, and integrate system status so that station and ground personnel can operate more efficiently. To use AA technology for the augmentation of system management functions requires a development model which consists of well defined phases of: evaluation, development, integration, and maintenance. The evaluation phase will consider system management functions against traditional solutions, implementation techniques and requirements; the end result of this phase should be a well developed concept along with a feasibility analysis. In the development phase the AA system will be developed in accordance with a traditional Life Cycle Model (LCM) modified for Knowledge Based System (KBS) applications. A way by which both knowledge bases and reasoning techniques can be reused to control costs is explained. During the integration phase the KBS software must be integrated with conventional software, and verified and validated. The Verification and Validation (V and V) techniques applicable to these KBS are based on the ideas of consistency, minimal competency, and graph theory. The maintenance phase will be aided by having well designed and documented KBS software.

Expert System Software

NASA Technical Reports Server (NTRS)

1989-01-01

C Language Integrated Production System (CLIPS) is a software shell for developing expert systems is designed to allow research and development of artificial intelligence on conventional computers. Originally developed by Johnson Space Center, it enables highly efficient pattern matching. A collection of conditions and actions to be taken if the conditions are met is built into a rule network. Additional pertinent facts are matched to the rule network. Using the program, E.I. DuPont de Nemours & Co. is monitoring chemical production machines; California Polytechnic State University is investigating artificial intelligence in computer aided design; Mentor Graphics has built a new Circuit Synthesis system, and Brooke and Brooke, a law firm, can determine which facts from a file are most important.

Space Environments and Effects Program (SEE)

NASA Technical Reports Server (NTRS)

Yhisreal-Rivas, David M.

2013-01-01

The need to preserve works and NASA documented articles is done via the collection of various Space Environments and Effects (SEE) related articles. (SEE) contains and lists the various projects that are ongoing, or have been conducted with the help of NASA. The goal of the (SEE) program is to make publicly available the environment technologies that are required to design, manufacture and operate reliable, cost-effective spacecraft for the government and commercial sectors. Of the many projects contained within the (SEE) program the Lunar-E Library and Spacecraft Materials Selector (SMS) have been selected for a more user friendly means to make the tools easily available to the public. This information which is still available required a person or entity to request access from a point of contact at NASA and wait for the requested bundled software DVD via postal service. Redesigning the material presentation and availability has been mapped to a single step process with faster turnaround time via Materials and Processes Technical Information System (MAPTIS) database. This process requires users to register and be verified in order to gain access to the information contained within. Aiding in the progression of making the software tools/documents available required a combination of specialized in-house data gathering software tools and software archeology.

Orbital transfer vehicle launch operations study: Manpower summary and facility requirements, volume 5

NASA Technical Reports Server (NTRS)

1986-01-01

All manpower numbers, number of heads (by skill), serial time and manhours have been accumulated and compiled on a per subtask basis in spreadsheet format for both the ground based and the space based data flows. To aid in identifying the facility resources required to process the Ground Based Orbital Transfer Vehicle (GBOTV) and/or the space based orbital transfer vehicle (SBOTV) through the ground facilities at Kennedy Space Center (KSC), a software application package was developed using a general purpose data base management system known as Data Flex. The facility requirements are used as the basic input to this software application. The resources of the KSC facility that could be used by orbital transfer vehicle program were digitized in the same format used to identify facility requirements. The facility capabilities were digitized in this format for subsequent, automated comparative analyses. Composite facility requirements are compared to each of the baseline facility capabilities and the system generates a relative score that indicates how each facility weighs against the composite requirements in relation to the other facilities in the set.

Software and resources for computational medicinal chemistry

PubMed Central

Liao, Chenzhong; Sitzmann, Markus; Pugliese, Angelo; Nicklaus, Marc C

2011-01-01

Computer-aided drug design plays a vital role in drug discovery and development and has become an indispensable tool in the pharmaceutical industry. Computational medicinal chemists can take advantage of all kinds of software and resources in the computer-aided drug design field for the purposes of discovering and optimizing biologically active compounds. This article reviews software and other resources related to computer-aided drug design approaches, putting particular emphasis on structure-based drug design, ligand-based drug design, chemical databases and chemoinformatics tools. PMID:21707404

Space crew radiation exposure analysis system based on a commercial stand-alone CAD system

NASA Technical Reports Server (NTRS)

Appleby, Matthew H.; Golightly, Michael J.; Hardy, Alva C.

1992-01-01

Major improvements have recently been completed in the approach to spacecraft shielding analysis. A Computer-Aided Design (CAD)-based system has been developed for determining the shielding provided to any point within or external to the spacecraft. Shielding analysis is performed using a commercially available stand-alone CAD system and a customized ray-tracing subroutine contained within a standard engineering modeling software package. This improved shielding analysis technique has been used in several vehicle design projects such as a Mars transfer habitat, pressurized lunar rover, and the redesigned Space Station. Results of these analyses are provided to demonstrate the applicability and versatility of the system.

The Effects of Computer-Aided Design Software on Engineering Students' Spatial Visualisation Skills

ERIC Educational Resources Information Center

Kösa, Temel; Karakus, Fatih

2018-01-01

The purpose of this study was to determine the influence of computer-aided design (CAD) software-based instruction on the spatial visualisation skills of freshman engineering students in a computer-aided engineering drawing course. A quasi-experimental design was applied, using the Purdue Spatial Visualization Test-Visualization of Rotations…

Modeling And Simulation Of Bar Code Scanners Using Computer Aided Design Software

NASA Astrophysics Data System (ADS)

Hellekson, Ron; Campbell, Scott

1988-06-01

Many optical systems have demanding requirements to package the system in a small 3 dimensional space. The use of computer graphic tools can be a tremendous aid to the designer in analyzing the optical problems created by smaller and less costly systems. The Spectra Physics grocery store bar code scanner employs an especially complex 3 dimensional scan pattern to read bar code labels. By using a specially written program which interfaces with a computer aided design system, we have simulated many of the functions of this complex optical system. In this paper we will illustrate how a recent version of the scanner has been designed. We will discuss the use of computer graphics in the design process including interactive tweaking of the scan pattern, analysis of collected light, analysis of the scan pattern density, and analysis of the manufacturing tolerances used to build the scanner.

Air Command and Staff College (ACSC) Academic Year (AY) 1999 Multimedia Yearbook

DTIC Science & Technology

1999-04-01

step in the project was to identify other software applications that would be beneficial in this endeavor. Initially, I reviewed a PC Magazine article...I looked at Adobe’s Photoshop  versions 4.0 and 5.0. This application is an extremely powerful graphics program, which aids in photo-retouching...application is our “bread and butter.” The advertising companies that have purchased space or provided services at a reduced price in exchange for

Updated Fatigue-Crack-Growth And Fracture-Mechanics Software

NASA Technical Reports Server (NTRS)

Forman, Royce G.; Shivakumar, Venkataraman; Newman, James C., Jr.

1995-01-01

NASA/FLAGRO 2.0 developed as analytical aid in predicting growth and stability of preexisting flaws and cracks in structural components of aerospace systems. Used for fracture-control analysis of space hardware. Organized into three modules to maximize efficiency in operation. Useful in: (1) crack-instability/crack-growth analysis, (2) processing raw crack-growth data from laboratory tests, and (3) boundary-element analysis to determine stresses and stress-intensity factors. Written in FORTRAN 77 and ANSI C.

DTD Creation for the Software Technology for Adaptable, Reliable Systems (STARS) Program

DTIC Science & Technology

1990-06-23

developed to store documents in a format peculiar to the program’s design . Editing the document became easy since word processors adjust all spacing and...descriptive markup may be output to a 3 CDRL 1810 January 26, 1990 variety of devices ranging from high quality typography printers through laser printers...provision for non-SGML material, such as graphics , to be inserted in a document. For these reasons the Computer-Aided Acquisition and Logistics Support

Incorporating Computer-Aided Software in the Undergraduate Chemical Engineering Core Courses

ERIC Educational Resources Information Center

Alnaizy, Raafat; Abdel-Jabbar, Nabil; Ibrahim, Taleb H.; Husseini, Ghaleb A.

2014-01-01

Introductions of computer-aided software and simulators are implemented during the sophomore-year of the chemical engineering (ChE) curriculum at the American University of Sharjah (AUS). Our faculty concurs that software integration within the curriculum is beneficial to our students, as evidenced by the positive feedback received from industry…

The Impact of Software on Associate Degree Programs in Electronic Engineering Technology.

ERIC Educational Resources Information Center

Hata, David M.

1986-01-01

Assesses the range and extent of computer assisted instruction software available in electronic engineering technology education. Examines the need for software skills in four areas: (1) high-level languages; (2) assembly language; (3) computer-aided engineering; and (4) computer-aided instruction. Outlines strategies for the future in three…

Software Application for Computer Aided Vocabulary Learning in a Blended Learning Environment

ERIC Educational Resources Information Center

Essam, Rasha

2010-01-01

This study focuses on the effect of computer-aided vocabulary learning software called "ArabCAVL" on students' vocabulary acquisition. It was hypothesized that students who use the ArabCAVL software in blended learning environment will surpass students who use traditional vocabulary learning strategies in face-to-face learning…

Computer-Aided Process and Tools for Mobile Software Acquisition

DTIC Science & Technology

2013-04-01

Software Acquisition Christopher Bonine , Man-Tak Shing, and Thomas W. Otani Naval Postgraduate School Published April 1, 2013 Approved for public...ManTech International Corporation Computer-Aided Process and Tools for Mobile Software Acquisition Christopher Bonine , Man-Tak Shing, and Thomas W. Otani...Mobile Software Acquisition Christopher Bonine — Bonine is a lieutenant in the United States Navy. He is currently assigned to the Navy Cyber Defense

Computer-Aided Software Engineering - An approach to real-time software development

NASA Technical Reports Server (NTRS)

Walker, Carrie K.; Turkovich, John J.

1989-01-01

A new software engineering discipline is Computer-Aided Software Engineering (CASE), a technology aimed at automating the software development process. This paper explores the development of CASE technology, particularly in the area of real-time/scientific/engineering software, and a history of CASE is given. The proposed software development environment for the Advanced Launch System (ALS CASE) is described as an example of an advanced software development system for real-time/scientific/engineering (RT/SE) software. The Automated Programming Subsystem of ALS CASE automatically generates executable code and corresponding documentation from a suitably formatted specification of the software requirements. Software requirements are interactively specified in the form of engineering block diagrams. Several demonstrations of the Automated Programming Subsystem are discussed.

Design Aids for Real-Time Systems (DARTS)

NASA Technical Reports Server (NTRS)

Szulewski, P. A.

1982-01-01

Design-Aids for Real-Time Systems (DARTS) is a tool that assists in defining embedded computer systems through tree structured graphics, military standard documentation support, and various analyses including automated Software Science parameter counting and metrics calculation. These analyses provide both static and dynamic design quality feedback which can potentially aid in producing efficient, high quality software systems.

A Functional Description of a Digital Flight Test System for Navigation and Guidance Research in the Terminal Area

NASA Technical Reports Server (NTRS)

Hegarty, D. M.

1974-01-01

A guidance, navigation, and control system, the Simulated Shuttle Flight Test System (SS-FTS), when interfaced with existing aircraft systems, provides a research facility for studying concepts for landing the space shuttle orbiter and conventional jet aircraft. The SS-FTS, which includes a general-purpose computer, performs all computations for precisely following a prescribed approach trajectory while properly managing the vehicle energy to allow safe arrival at the runway and landing within prescribed dispersions. The system contains hardware and software provisions for navigation with several combinations of possible navigation aids that have been suggested for the shuttle. The SS-FTS can be reconfigured to study different guidance and navigation concepts by changing only the computer software, and adapted to receive different radio navigation information through minimum hardware changes. All control laws, logic, and mode interlocks reside solely in the computer software.

Development of the ISS EMU Dashboard Software

NASA Technical Reports Server (NTRS)

Bernard, Craig; Hill, Terry R.

2011-01-01

The EMU (Extra-Vehicular Mobility Unit) Dashboard was developed at NASA s Johnson Space Center to aid in real-time mission support for the ISS (International Space Station) and Shuttle EMU space suit by time synchronizing down-linked video, space suit data and audio from the mission control audio loops. Once the input streams are synchronized and recorded, the data can be replayed almost instantly and has proven invaluable in understanding in-flight hardware anomalies and playing back information conveyed by the crew to missions control and the back room support. This paper will walk through the development from an engineer s idea brought to life by an intern to real time mission support and how this tool is evolving today and its challenges to support EVAs (Extra-Vehicular Activities) and human exploration in the 21st century.

Caesy: A software tool for computer-aided engineering

NASA Technical Reports Server (NTRS)

Wette, Matt

1993-01-01

A new software tool, Caesy, is described. This tool provides a strongly typed programming environment for research in the development of algorithms and software for computer-aided control system design. A description of the user language and its implementation as they currently stand are presented along with a description of work in progress and areas of future work.

Diagnostic performance of an automated analysis software for the diagnosis of Alzheimer’s dementia with 18F FDG PET

PubMed Central

Partovi, Sasan; Yuh, Roger; Pirozzi, Sara; Lu, Ziang; Couturier, Spencer; Grosse, Ulrich; Schluchter, Mark D; Nelson, Aaron; Jones, Robert; O’Donnell, James K; Faulhaber, Peter

2017-01-01

The objective of this study was to assess the ability of a quantitative software-aided approach to improve the diagnostic accuracy of 18F FDG PET for Alzheimer’s dementia over visual analysis alone. Twenty normal subjects (M:F-12:8; mean age 80.6 years) and twenty mild AD subjects (M:F-12:8; mean age 70.6 years) with 18F FDG PET scans were obtained from the ADNI database. Three blinded readers interpreted these PET images first using a visual qualitative approach and then using a quantitative software-aided approach. Images were classified on two five-point scales based on normal/abnormal (1-definitely normal; 5-definitely abnormal) and presence of AD (1-definitely not AD; 5-definitely AD). Diagnostic sensitivity, specificity, and accuracy for both approaches were compared based on the aforementioned scales. The sensitivity, specificity, and accuracy for the normal vs. abnormal readings of all readers combined were higher when comparing the software-aided vs. visual approach (sensitivity 0.93 vs. 0.83 P = 0.0466; specificity 0.85 vs. 0.60 P = 0.0005; accuracy 0.89 vs. 0.72 P<0.0001). The specificity and accuracy for absence vs. presence of AD of all readers combined were higher when comparing the software-aided vs. visual approach (specificity 0.90 vs. 0.70 P = 0.0008; accuracy 0.81 vs. 0.72 P = 0.0356). Sensitivities of the software-aided and visual approaches did not differ significantly (0.72 vs. 0.73 P = 0.74). The quantitative software-aided approach appears to improve the performance of 18F FDG PET for the diagnosis of mild AD. It may be helpful for experienced 18F FDG PET readers analyzing challenging cases. PMID:28123864

Building Safer Systems With SpecTRM

NASA Technical Reports Server (NTRS)

2003-01-01

System safety, an integral component in software development, often poses a challenge to engineers designing computer-based systems. While the relaxed constraints on software design allow for increased power and flexibility, this flexibility introduces more possibilities for error. As a result, system engineers must identify the design constraints necessary to maintain safety and ensure that the system and software design enforces them. Safeware Engineering Corporation, of Seattle, Washington, provides the information, tools, and techniques to accomplish this task with its Specification Tools and Requirements Methodology (SpecTRM). NASA assisted in developing this engineering toolset by awarding the company several Small Business Innovation Research (SBIR) contracts with Ames Research Center and Langley Research Center. The technology benefits NASA through its applications for Space Station rendezvous and docking. SpecTRM aids system and software engineers in developing specifications for large, complex safety critical systems. The product enables engineers to find errors early in development so that they can be fixed with the lowest cost and impact on the system design. SpecTRM traces both the requirements and design rationale (including safety constraints) throughout the system design and documentation, allowing engineers to build required system properties into the design from the beginning, rather than emphasizing assessment at the end of the development process when changes are limited and costly.System safety, an integral component in software development, often poses a challenge to engineers designing computer-based systems. While the relaxed constraints on software design allow for increased power and flexibility, this flexibility introduces more possibilities for error. As a result, system engineers must identify the design constraints necessary to maintain safety and ensure that the system and software design enforces them. Safeware Engineering Corporation, of Seattle, Washington, provides the information, tools, and techniques to accomplish this task with its Specification Tools and Requirements Methodology (SpecTRM). NASA assisted in developing this engineering toolset by awarding the company several Small Business Innovation Research (SBIR) contracts with Ames Research Center and Langley Research Center. The technology benefits NASA through its applications for Space Station rendezvous and docking. SpecTRM aids system and software engineers in developing specifications for large, complex safety critical systems. The product enables engineers to find errors early in development so that they can be fixed with the lowest cost and impact on the system design. SpecTRM traces both the requirements and design rationale (including safety constraints) throughout the system design and documentation, allowing engineers to build required system properties into the design from the beginning, rather than emphasizing assessment at the end of the development process when changes are limited and costly.

Operations management system

NASA Technical Reports Server (NTRS)

Brandli, A. E.; Eckelkamp, R. E.; Kelly, C. M.; Mccandless, W.; Rue, D. L.

1990-01-01

The objective of an operations management system is to provide an orderly and efficient method to operate and maintain aerospace vehicles. Concepts are described for an operations management system and the key technologies are highlighted which will be required if this capability is brought to fruition. Without this automation and decision aiding capability, the growing complexity of avionics will result in an unmanageable workload for the operator, ultimately threatening mission success or survivability of the aircraft or space system. The key technologies include expert system application to operational tasks such as replanning, equipment diagnostics and checkout, global system management, and advanced man machine interfaces. The economical development of operations management systems, which are largely software, will require advancements in other technological areas such as software engineering and computer hardware.

Developing Signal-Pattern-Recognition Programs

NASA Technical Reports Server (NTRS)

Shelton, Robert O.; Hammen, David

2006-01-01

Pattern Interpretation and Recognition Application Toolkit Environment (PIRATE) is a block-oriented software system that aids the development of application programs that analyze signals in real time in order to recognize signal patterns that are indicative of conditions or events of interest. PIRATE was originally intended for use in writing application programs to recognize patterns in space-shuttle telemetry signals received at Johnson Space Center's Mission Control Center: application programs were sought to (1) monitor electric currents on shuttle ac power busses to recognize activations of specific power-consuming devices, (2) monitor various pressures and infer the states of affected systems by applying a Kalman filter to the pressure signals, (3) determine fuel-leak rates from sensor data, (4) detect faults in gyroscopes through analysis of system measurements in the frequency domain, and (5) determine drift rates in inertial measurement units by regressing measurements against time. PIRATE can also be used to develop signal-pattern-recognition software for different purposes -- for example, to monitor and control manufacturing processes.

COMPASS: A general purpose computer aided scheduling tool

NASA Technical Reports Server (NTRS)

Mcmahon, Mary Beth; Fox, Barry; Culbert, Chris

1991-01-01

COMPASS is a generic scheduling system developed by McDonnell Douglas under the direction of the Software Technology Branch at JSC. COMPASS is intended to illustrate the latest advances in scheduling technology and provide a basis from which custom scheduling systems can be built. COMPASS was written in Ada to promote readability and to conform to potential NASA Space Station Freedom standards. COMPASS has some unique characteristics that distinguishes it from commercial products. These characteristics are discussed and used to illustrate some differences between scheduling tools.

Advanced earth observation spacecraft computer-aided design software: Technical, user and programmer guide

NASA Technical Reports Server (NTRS)

Farrell, C. E.; Krauze, L. D.

1983-01-01

The IDEAS computer of NASA is a tool for interactive preliminary design and analysis of LSS (Large Space System). Nine analysis modules were either modified or created. These modules include the capabilities of automatic model generation, model mass properties calculation, model area calculation, nonkinematic deployment modeling, rigid-body controls analysis, RF performance prediction, subsystem properties definition, and EOS science sensor selection. For each module, a section is provided that contains technical information, user instructions, and programmer documentation.

Astronomy Aid

NASA Technical Reports Server (NTRS)

1995-01-01

As a Jet Propulsion Laboratory astronomer, John D. Callahan developed a computer program called Multimission Interactive Planner (MIP) to help astronomers analyze scientific and optical data collected on the Voyager's Grand Tour. The commercial version of the program called XonVu is published by XonTech, Inc. Callahan has since developed two more advanced programs based on MIP technology, Grand Tour and Jovian Traveler, which simulate Voyager and Giotto missions. The software allows astronomers and space novices to view the objects seen by the spacecraft, manipulating perspective, distance and field of vision.

Software For Computer-Aided Design Of Control Systems

NASA Technical Reports Server (NTRS)

Wette, Matthew

1994-01-01

Computer Aided Engineering System (CAESY) software developed to provide means to evaluate methods for dealing with users' needs in computer-aided design of control systems. Interpreter program for performing engineering calculations. Incorporates features of both Ada and MATLAB. Designed to be flexible and powerful. Includes internally defined functions, procedures and provides for definition of functions and procedures by user. Written in C language.

CAD-based stand-alone spacecraft radiation exposure analysis system: An application of the early man-tended Space Station

NASA Technical Reports Server (NTRS)

Appleby, M. H.; Golightly, M. J.; Hardy, A. C.

1993-01-01

Major improvements have been completed in the approach to analyses and simulation of spacecraft radiation shielding and exposure. A computer-aided design (CAD)-based system has been developed for determining the amount of shielding provided by a spacecraft and simulating transmission of an incident radiation environment to any point within or external to the vehicle. Shielding analysis is performed using a customized ray-tracing subroutine contained within a standard engineering modeling software package. This improved shielding analysis technique has been used in several vehicle design programs such as a Mars transfer habitat, pressurized lunar rover, and the redesigned international Space Station. Results of analysis performed for the Space Station astronaut exposure assessment are provided to demonastrate the applicability and versatility of the system.

Key Issues in Instructional Computer Graphics.

ERIC Educational Resources Information Center

Wozny, Michael J.

1981-01-01

Addresses key issues facing universities which plan to establish instructional computer graphics facilities, including computer-aided design/computer aided manufacturing systems, role in curriculum, hardware, software, writing instructional software, faculty involvement, operations, and research. Thirty-seven references and two appendices are…

A general-purpose development environment for intelligent computer-aided training systems

NASA Technical Reports Server (NTRS)

Savely, Robert T.

1990-01-01

Space station training will be a major task, requiring the creation of large numbers of simulation-based training systems for crew, flight controllers, and ground-based support personnel. Given the long duration of space station missions and the large number of activities supported by the space station, the extension of space shuttle training methods to space station training may prove to be impractical. The application of artificial intelligence technology to simulation training can provide the ability to deliver individualized training to large numbers of personnel in a distributed workstation environment. The principal objective of this project is the creation of a software development environment which can be used to build intelligent training systems for procedural tasks associated with the operation of the space station. Current NASA Johnson Space Center projects and joint projects with other NASA operational centers will result in specific training systems for existing space shuttle crew, ground support personnel, and flight controller tasks. Concurrently with the creation of these systems, a general-purpose development environment for intelligent computer-aided training systems will be built. Such an environment would permit the rapid production, delivery, and evolution of training systems for space station crew, flight controllers, and other support personnel. The widespread use of such systems will serve to preserve task and training expertise, support the training of many personnel in a distributed manner, and ensure the uniformity and verifiability of training experiences. As a result, significant reductions in training costs can be realized while safety and the probability of mission success can be enhanced.

Launch Commit Criteria Monitoring Agent

NASA Technical Reports Server (NTRS)

Semmel, Glenn S.; Davis, Steven R.; Leucht, Kurt W.; Rowe, Dan A.; Kelly, Andrew O.; Boeloeni, Ladislau

2005-01-01

The Spaceport Processing Systems Branch at NASA Kennedy Space Center has developed and deployed a software agent to monitor the Space Shuttle's ground processing telemetry stream. The application, the Launch Commit Criteria Monitoring Agent, increases situational awareness for system and hardware engineers during Shuttle launch countdown. The agent provides autonomous monitoring of the telemetry stream, automatically alerts system engineers when predefined criteria have been met, identifies limit warnings and violations of launch commit criteria, aids Shuttle engineers through troubleshooting procedures, and provides additional insight to verify appropriate troubleshooting of problems by contractors. The agent has successfully detected launch commit criteria warnings and violations on a simulated playback data stream. Efficiency and safety are improved through increased automation.

Advanced Integrated Display System V/STOL Program Performance Specification. Volume I.

DTIC Science & Technology

1980-06-01

sensor inputs required before the sensor can be designated acceptable. The reactivation count of each sensor parameter which satisfies its veri...129 3.5.2 AIDS Configuration Parameters .............. 133 3.5.3 AIDS Throughput Requirements ............... 133 4 QUALITY ASSURANCE...lists the adaptation parameters of the AIDS software; these parameters include the throughput and memory requirements of the software. 3.2 SYSTEM

CAD/CAE Integration Enhanced by New CAD Services Standard

NASA Technical Reports Server (NTRS)

Claus, Russell W.

2002-01-01

A Government-industry team led by the NASA Glenn Research Center has developed a computer interface standard for accessing data from computer-aided design (CAD) systems. The Object Management Group, an international computer standards organization, has adopted this CAD services standard. The new standard allows software (e.g., computer-aided engineering (CAE) and computer-aided manufacturing software to access multiple CAD systems through one programming interface. The interface is built on top of a distributed computing system called the Common Object Request Broker Architecture (CORBA). CORBA allows the CAD services software to operate in a distributed, heterogeneous computing environment.

Computer-aided software development process design

NASA Technical Reports Server (NTRS)

Lin, Chi Y.; Levary, Reuven R.

1989-01-01

The authors describe an intelligent tool designed to aid managers of software development projects in planning, managing, and controlling the development process of medium- to large-scale software projects. Its purpose is to reduce uncertainties in the budget, personnel, and schedule planning of software development projects. It is based on dynamic model for the software development and maintenance life-cycle process. This dynamic process is composed of a number of time-varying, interacting developmental phases, each characterized by its intended functions and requirements. System dynamics is used as a modeling methodology. The resulting Software LIfe-Cycle Simulator (SLICS) and the hybrid expert simulation system of which it is a subsystem are described.

[Three-dimensional computer aided design for individualized post-and-core restoration].

PubMed

Gu, Xiao-yu; Wang, Ya-ping; Wang, Yong; Lü, Pei-jun

2009-10-01

To develop a method of three-dimensional computer aided design (CAD) of post-and-core restoration. Two plaster casts with extracted natural teeth were used in this study. The extracted teeth were prepared and scanned using tomography method to obtain three-dimensional digitalized models. According to the basic rules of post-and-core design, posts, cores and cavity surfaces of the teeth were designed using the tools for processing point clouds, curves and surfaces on the forward engineering software of Tanglong prosthodontic system. Then three-dimensional figures of the final restorations were corrected according to the configurations of anterior teeth, premolars and molars respectively. Computer aided design of 14 post-and-core restorations were finished, and good fitness between the restoration and the three-dimensional digital models were obtained. Appropriate retention forms and enough spaces for the full crown restorations can be obtained through this method. The CAD of three-dimensional figures of the post-and-core restorations can fulfill clinical requirements. Therefore they can be used in computer-aided manufacture (CAM) of post-and-core restorations.

A Study of the Use of Ontologies for Building Computer-Aided Control Engineering Self-Learning Educational Software

ERIC Educational Resources Information Center

García, Isaías; Benavides, Carmen; Alaiz, Héctor; Alonso, Angel

2013-01-01

This paper describes research on the use of knowledge models (ontologies) for building computer-aided educational software in the field of control engineering. Ontologies are able to represent in the computer a very rich conceptual model of a given domain. This model can be used later for a number of purposes in different software applications. In…

Applications of Modeling and Simulation for Flight Hardware Processing at Kennedy Space Center

NASA Technical Reports Server (NTRS)

Marshall, Jennifer L.

2010-01-01

The Boeing Design Visualization Group (DVG) is responsible for the creation of highly-detailed representations of both on-site facilities and flight hardware using computer-aided design (CAD) software, with a focus on the ground support equipment (GSE) used to process and prepare the hardware for space. Throughout my ten weeks at this center, I have had the opportunity to work on several projects: the modification of the Multi-Payload Processing Facility (MPPF) High Bay, weekly mapping of the Space Station Processing Facility (SSPF) floor layout, kinematics applications for the Orion Command Module (CM) hatches, and the design modification of the Ares I Upper Stage hatch for maintenance purposes. The main goal of each of these projects was to generate an authentic simulation or representation using DELMIA V5 software. This allowed for evaluation of facility layouts, support equipment placement, and greater process understanding once it was used to demonstrate future processes to customers and other partners. As such, I have had the opportunity to contribute to a skilled team working on diverse projects with a central goal of providing essential planning resources for future center operations.

Tracking Debris Shed by a Space-Shuttle Launch Vehicle

NASA Technical Reports Server (NTRS)

Stuart, Phillip C.; Rogers, Stuart E.

2009-01-01

The DEBRIS software predicts the trajectories of debris particles shed by a space-shuttle launch vehicle during ascent, to aid in assessing potential harm to the space-shuttle orbiter and crew. The user specifies the location of release and other initial conditions for a debris particle. DEBRIS tracks the particle within an overset grid system by means of a computational fluid dynamics (CFD) simulation of the local flow field and a ballistic simulation that takes account of the mass of the particle and its aerodynamic properties in the flow field. The computed particle trajectory is stored in a file to be post-processed by other software for viewing and analyzing the trajectory. DEBRIS supplants a prior debris tracking code that took .15 minutes to calculate a single particle trajectory: DEBRIS can calculate 1,000 trajectories in .20 seconds on a desktop computer. Other improvements over the prior code include adaptive time-stepping to ensure accuracy, forcing at least one step per grid cell to ensure resolution of all CFD-resolved flow features, ability to simulate rebound of debris from surfaces, extensive error checking, a builtin suite of test cases, and dynamic allocation of memory.

USE OF COMPUTER-AIDED PROCESS ENGINEERING TOOL IN POLLUTION PREVENTION

EPA Science Inventory

Computer-Aided Process Engineering has become established in industry as a design tool. With the establishment of the CAPE-OPEN software specifications for process simulation environments. CAPE-OPEN provides a set of "middleware" standards that enable software developers to acces...

Proof of Concept Study of Trade Space Configuration Tool for Spacecraft Design

NASA Technical Reports Server (NTRS)

Glidden, Geoffrey L.

2009-01-01

Spacecraft design is a very difficult and time consuming process because requirements and criteria are often changed or modified as the design is refined. Accounting for these adjustments in the design constraints plays a significant role in furthering the overall progress. There are numerous aspects and variables that hold significant influence on various characteristics of the design. This can be especially frustrating when attempting to conduct rapid trade space analysis on system configurations. Currently, the data and designs considered for trade space evaluations can only be displayed by using the traditional interfaces of Excel spreadsheets or CAD (Computer Aided Design) models. While helpful, these methods of analyzing the data from a systems engineering approach can be rather complicated and overwhelming. As a result, a proof of concept was conducted on a dynamic data visualization software called Thinkmap SDK (Software Developer Kit) to allow for better organization and understanding of the relationships between the various aspects that make up an entire design. The Orion Crew Module Aft Bay Subsystem was used as the test case for this study because the design and layout of many of the subsystem components will be significant in ensuring the overall center of gravity of the capsule is correct. A simplified model of this subsystem was created and programmed using Thinkmap SDK to create a preliminary prototype application of a Trade Space Configuration Tool. The completed application ensures that the core requirements for the Tool can be met. Further development is strongly suggested to produce a full prototype application to allow final evaluations and recommendations of the software capabilities.

Automated Subsystem Control for Life Support System (ASCLSS)

NASA Technical Reports Server (NTRS)

Block, Roger F.

1987-01-01

The Automated Subsystem Control for Life Support Systems (ASCLSS) program has successfully developed and demonstrated a generic approach to the automation and control of space station subsystems. The automation system features a hierarchical and distributed real-time control architecture which places maximum controls authority at the lowest or process control level which enhances system autonomy. The ASCLSS demonstration system pioneered many automation and control concepts currently being considered in the space station data management system (DMS). Heavy emphasis is placed on controls hardware and software commonality implemented in accepted standards. The approach demonstrates successfully the application of real-time process and accountability with the subsystem or process developer. The ASCLSS system completely automates a space station subsystem (air revitalization group of the ASCLSS) which moves the crew/operator into a role of supervisory control authority. The ASCLSS program developed over 50 lessons learned which will aide future space station developers in the area of automation and controls..

Creation of Anatomically Accurate Computer-Aided Design (CAD) Solid Models from Medical Images

NASA Technical Reports Server (NTRS)

Stewart, John E.; Graham, R. Scott; Samareh, Jamshid A.; Oberlander, Eric J.; Broaddus, William C.

1999-01-01

Most surgical instrumentation and implants used in the world today are designed with sophisticated Computer-Aided Design (CAD)/Computer-Aided Manufacturing (CAM) software. This software automates the mechanical development of a product from its conceptual design through manufacturing. CAD software also provides a means of manipulating solid models prior to Finite Element Modeling (FEM). Few surgical products are designed in conjunction with accurate CAD models of human anatomy because of the difficulty with which these models are created. We have developed a novel technique that creates anatomically accurate, patient specific CAD solids from medical images in a matter of minutes.

Proceedings of the Workshop on Computational Aspects in the Control of Flexible Systems, part 1

NASA Technical Reports Server (NTRS)

Taylor, Lawrence W., Jr. (Compiler)

1989-01-01

Control/Structures Integration program software needs, computer aided control engineering for flexible spacecraft, computer aided design, computational efficiency and capability, modeling and parameter estimation, and control synthesis and optimization software for flexible structures and robots are among the topics discussed.

The Synergistic Engineering Environment

NASA Technical Reports Server (NTRS)

Cruz, Jonathan

2006-01-01

The Synergistic Engineering Environment (SEE) is a system of software dedicated to aiding the understanding of space mission operations. The SEE can integrate disparate sets of data with analytical capabilities, geometric models of spacecraft, and a visualization environment, all contributing to the creation of an interactive simulation of spacecraft. Initially designed to satisfy needs pertaining to the International Space Station, the SEE has been broadened in scope to include spacecraft ranging from those in low orbit around the Earth to those on deep-space missions. The SEE includes analytical capabilities in rigid-body dynamics, kinematics, orbital mechanics, and payload operations. These capabilities enable a user to perform real-time interactive engineering analyses focusing on diverse aspects of operations, including flight attitudes and maneuvers, docking of visiting spacecraft, robotic operations, impingement of spacecraft-engine exhaust plumes, obscuration of instrumentation fields of view, communications, and alternative assembly configurations. .

Recipe for Success: Digital Viewables

NASA Technical Reports Server (NTRS)

LaPha, Steven; Gaydos, Frank

2014-01-01

The Engineering Services Contract (ESC) and Information Management Communication Support contract (IMCS) at Kennedy Space Center (KSC) provide services to NASA in respect to flight and ground systems design and development. These groups provides the necessary tools, aid, and best practice methodologies required for efficient, optimized design and process development. The team is responsible for configuring and implementing systems, software, along with training, documentation, and administering standards. The team supports over 200 engineers and design specialists with the use of Windchill, Creo Parametric, NX, AutoCAD, and a variety of other design and analysis tools.

Human Factors Model

NASA Technical Reports Server (NTRS)

1993-01-01

Jack is an advanced human factors software package that provides a three dimensional model for predicting how a human will interact with a given system or environment. It can be used for a broad range of computer-aided design applications. Jack was developed by the computer Graphics Research Laboratory of the University of Pennsylvania with assistance from NASA's Johnson Space Center, Ames Research Center and the Army. It is the University's first commercial product. Jack is still used for academic purposes at the University of Pennsylvania. Commercial rights were given to Transom Technologies, Inc.

Multi-stage learning aids applied to hands-on software training.

PubMed

Rother, Kristian; Rother, Magdalena; Pleus, Alexandra; Upmeier zu Belzen, Annette

2010-11-01

Delivering hands-on tutorials on bioinformatics software and web applications is a challenging didactic scenario. The main reason is that trainees have heterogeneous backgrounds, different previous knowledge and vary in learning speed. In this article, we demonstrate how multi-stage learning aids can be used to allow all trainees to progress at a similar speed. In this technique, the trainees can utilize cards with hints and answers to guide themselves self-dependently through a complex task. We have successfully conducted a tutorial for the molecular viewer PyMOL using two sets of learning aid cards. The trainees responded positively, were able to complete the task, and the trainer had spare time to respond to individual questions. This encourages us to conclude that multi-stage learning aids overcome many disadvantages of established forms of hands-on software training.

Selecting Software for Libraries.

ERIC Educational Resources Information Center

Beiser, Karl

1993-01-01

Discusses resources and strategies that libraries can use to evaluate competing database management software for purchase. Needs assessments, types of software available, features of good software, evaluation aids, shareware, and marketing and product trends are covered. (KRN)

A Succinct Naming Convention for Lengthy Hexadecimal Numbers

NASA Technical Reports Server (NTRS)

Grant, Michael S.

1997-01-01

Engineers, computer scientists, mathematicians and others must often deal with lengthy hexadecimal numbers. As memory requirements for software increase, the associated memory address space for systems necessitates the use of longer and longer strings of hexadecimal characters to describe a given number. For example, the address space of some digital signal processors (DSP's) now ranges in the billions of words, requiring eight hexadecimal characters for many of the addresses. This technical memorandum proposes a simple grouping scheme for more clearly representing lengthy hexadecimal numbers in written material, as well as a "code" for naming and more quickly verbalizing such numbers. This should facilitate communications among colleagues in engineering and related fields, and aid in comprehension and temporary memorization of important hexadecimal numbers during design work.

XRayView: a teaching aid for X-ray crystallography.

PubMed

Phillips, G N

1995-10-01

A software package, XRayView, has been developed that uses interactive computer graphics to introduce basic concepts of x-ray diffraction by crystals, including the reciprocal lattice, the Ewald sphere construction, Laue cones, the wavelength dependence of the reciprocal lattice, primitive and centered lattices and systematic extinctions, rotation photography. Laue photography, space group determination and Laue group symmetry, and the alignment of crystals by examination of reciprocal space. XRayView is designed with "user-friendliness" in mind, using pull-down menus to control the program. Many of the experiences of using real x-ray diffraction equipment to examine crystalline diffraction can be simulated. Exercises are available on-line to guide the users through many typical x-ray diffraction experiments.

Development of interactive multimedia applications

NASA Technical Reports Server (NTRS)

Leigh, Albert; Wang, Lui

1993-01-01

Multimedia is making an increasingly significant contribution to our informational society. The usefulness of this technology is already evident in education, business presentations, informational kiosks (e.g., in museums), training and the entertainment environment. Institutions, from grade schools to medical schools, are exploring the use of multifaceted electronic text books and teaching aids to enhance course materials. Through multimedia, teachers and students can take full advantage of the cognitive value of animation, audio, video and other types in a seamless application. The Software Technology Branch at NASA Johnson Space Center (NASA/JSC) is taking similar approaches to apply the state-of-the-art technology to space training, mission operations and other applications. This paper discusses the characteristics and development of multimedia applications at the NASA/JSC.

Applications of intelligent computer-aided training

NASA Technical Reports Server (NTRS)

Loftin, R. B.; Savely, Robert T.

1991-01-01

Intelligent computer-aided training (ICAT) systems simulate the behavior of an experienced instructor observing a trainee, responding to help requests, diagnosing and remedying trainee errors, and proposing challenging new training scenarios. This paper presents a generic ICAT architecture that supports the efficient development of ICAT systems for varied tasks. In addition, details of ICAT projects, built with this architecture, that deliver specific training for Space Shuttle crew members, ground support personnel, and flight controllers are presented. Concurrently with the creation of specific ICAT applications, a general-purpose software development environment for ICAT systems is being built. The widespread use of such systems for both ground-based and on-orbit training will serve to preserve task and training expertise, support the training of large numbers of personnel in a distributed manner, and ensure the uniformity and verifiability of training experiences.

Computer Aided Learning of Mathematics: Software Evaluation

ERIC Educational Resources Information Center

Yushau, B.; Bokhari, M. A.; Wessels, D. C. J.

2004-01-01

Computer Aided Learning of Mathematics (CALM) has been in use for some time in the Prep-Year Mathematics Program at King Fahd University of Petroleum & Minerals. Different kinds of software (both locally designed and imported) have been used in the quest of optimizing the recitation/problem session hour of the mathematics classes. This paper…

The Implications of Cognitive Psychology for Computer-Based Learning Tools.

ERIC Educational Resources Information Center

Kozma, Robert B.

1987-01-01

Defines cognitive computer tools as software programs that use the control capabilities of computers to amplify, extend, or enhance human cognition; suggests seven ways in which computers can aid learning; and describes the "Learning Tool," a software package for the Apple Macintosh microcomputer that is designed to aid learning of…

ECLIPSE, an Emerging Standardized Modular, Secure and Affordable Software Toolset in Support of Product Assurance, Quality Assurance and Project Management for the Entire European Space Industry (from Innovative SMEs to Primes and Institutions)

NASA Astrophysics Data System (ADS)

Bennetti, Andrea; Ansari, Salim; Dewhirst, Tori; Catanese, Giuseppe

2010-08-01

The development of satellites and ground systems (and the technologies that support them) is complex and demands a great deal of rigor in the management of both the information it relies upon and the information it generates via the performance of well established processes. To this extent for the past fifteen years Sapienza Consulting has been supporting the European Space Agency (ESA) in the management of this information and provided ESA with ECSS (European Cooperation for Space Standardization) Standards based Project Management (PM), Product Assurance (PA) and Quality Assurance (QA) software applications. In 2009 Sapienza recognised the need to modernize, standardizing and integrate its core ECSS-based software tools into a single yet modularised suite of applications named ECLIPSE aimed at: • Fulfilling a wider range of historical and emerging requirements, • Providing a better experience for users, • Increasing the value of the information it collects and manages • Lowering the cost of ownership and operation • Increasing collaboration within and between space sector organizations • Aiding in the performance of several PM, PA, QA, and configuration management tasks in adherence to ECSS standards. In this paper, Sapienza will first present the toolset, and a rationale for its development, describing and justifying its architecture, and basic modules composition. Having defined the toolset architecture, this paper will address the current status of the individual applications. A compliance assessment will be presented for each module in the toolset with respect to the ECSS standard it addresses. Lastly experience from early industry and Institutional users will be presented.

Eighteen-Month Outcomes of Titanium Frameworks Using Computer-Aided Design and Computer-Aided Manufacturing Method.

PubMed

Turkyilmaz, Ilser; Asar, Neset Volkan

2017-06-01

The aim of the report is to introduce a new software and a new scanner with a noncontact laser probe and to present outcomes of computer-aided design and computer-aided manufacturing titanium frameworks using this new software and scanner with a laser probe. Seven patients received 40 implants placed using a 1-stage protocol. After all implants were planned using an implant planning software (NobelClinician), either 5 or 6 implants were placed in each edentulous arch. Each edentulous arch was treated with a fixed dental prosthesis using implant-supported complete-arch milled-titanium framework using the software (NobelProcera) and the scanner. All patients were followed up for 18 ± 3 months. Implant survival, prosthesis survival, framework fit, marginal bone levels, and maintenance requirements were evaluated. One implant was lost during the follow-up period, giving the implant survival rate of 97.5%; 0.4 ± 0.2 mm marginal bone loss was noted for all implants after 18 ± 3 months. None of the prostheses needed a replacement, indicating the prosthesis success rate of 100%. The results of this clinical study suggest that titanium frameworks fabricated using the software and scanner presented in this study fit accurately and may be a viable option to restore edentulous arches.

Space Flight Software Development Software for Intelligent System Health Management

NASA Technical Reports Server (NTRS)

Trevino, Luis C.; Crumbley, Tim

2004-01-01

The slide presentation examines the Marshall Space Flight Center Flight Software Branch, including software development projects, mission critical space flight software development, software technical insight, advanced software development technologies, and continuous improvement in the software development processes and methods.

Overview of computational control research at UT Austin

NASA Technical Reports Server (NTRS)

Bong, Wie

1989-01-01

An overview of current research activities at UT Austin is presented to discuss certain technical issues in the following areas: (1) Computer-Aided Nonlinear Control Design: In this project, the describing function method is employed for the nonlinear control analysis and design of a flexible spacecraft equipped with pulse modulated reaction jets. INCA program has been enhanced to allow the numerical calculation of describing functions as well as the nonlinear limit cycle analysis capability in the frequency domain; (2) Robust Linear Quadratic Gaussian (LQG) Compensator Synthesis: Robust control design techniques and software tools are developed for flexible space structures with parameter uncertainty. In particular, an interactive, robust multivariable control design capability is being developed for INCA program; and (3) LQR-Based Autonomous Control System for the Space Station: In this project, real time implementation of LQR-based autonomous control system is investigated for the space station with time-varying inertias and with significant multibody dynamic interactions.

Accuracy and efficiency of computer-aided anatomical analysis using 3D visualization software based on semi-automated and automated segmentations.

PubMed

An, Gao; Hong, Li; Zhou, Xiao-Bing; Yang, Qiong; Li, Mei-Qing; Tang, Xiang-Yang

2017-03-01

We investigated and compared the functionality of two 3D visualization software provided by a CT vendor and a third-party vendor, respectively. Using surgical anatomical measurement as baseline, we evaluated the accuracy of 3D visualization and verified their utility in computer-aided anatomical analysis. The study cohort consisted of 50 adult cadavers fixed with the classical formaldehyde method. The computer-aided anatomical analysis was based on CT images (in DICOM format) acquired by helical scan with contrast enhancement, using a CT vendor provided 3D visualization workstation (Syngo) and a third-party 3D visualization software (Mimics) that was installed on a PC. Automated and semi-automated segmentations were utilized in the 3D visualization workstation and software, respectively. The functionality and efficiency of automated and semi-automated segmentation methods were compared. Using surgical anatomical measurement as a baseline, the accuracy of 3D visualization based on automated and semi-automated segmentations was quantitatively compared. In semi-automated segmentation, the Mimics 3D visualization software outperformed the Syngo 3D visualization workstation. No significant difference was observed in anatomical data measurement by the Syngo 3D visualization workstation and the Mimics 3D visualization software (P>0.05). Both the Syngo 3D visualization workstation provided by a CT vendor and the Mimics 3D visualization software by a third-party vendor possessed the needed functionality, efficiency and accuracy for computer-aided anatomical analysis. Copyright © 2016 Elsevier GmbH. All rights reserved.

Combined Electric and Acoustic Stimulation With Hearing Preservation: Effect of Cochlear Implant Low-Frequency Cutoff on Speech Understanding and Perceived Listening Difficulty.

PubMed

Gifford, René H; Davis, Timothy J; Sunderhaus, Linsey W; Menapace, Christine; Buck, Barbara; Crosson, Jillian; O'Neill, Lori; Beiter, Anne; Segel, Phil

The primary objective of this study was to assess the effect of electric and acoustic overlap for speech understanding in typical listening conditions using semidiffuse noise. This study used a within-subjects, repeated measures design including 11 experienced adult implant recipients (13 ears) with functional residual hearing in the implanted and nonimplanted ear. The aided acoustic bandwidth was fixed and the low-frequency cutoff for the cochlear implant (CI) was varied systematically. Assessments were completed in the R-SPACE sound-simulation system which includes a semidiffuse restaurant noise originating from eight loudspeakers placed circumferentially about the subject's head. AzBio sentences were presented at 67 dBA with signal to noise ratio varying between +10 and 0 dB determined individually to yield approximately 50 to 60% correct for the CI-alone condition with full CI bandwidth. Listening conditions for all subjects included CI alone, bimodal (CI + contralateral hearing aid), and bilateral-aided electric and acoustic stimulation (EAS; CI + bilateral hearing aid). Low-frequency cutoffs both below and above the original "clinical software recommendation" frequency were tested for all patients, in all conditions. Subjects estimated listening difficulty for all conditions using listener ratings based on a visual analog scale. Three primary findings were that (1) there was statistically significant benefit of preserved acoustic hearing in the implanted ear for most overlap conditions, (2) the default clinical software recommendation rarely yielded the highest level of speech recognition (1 of 13 ears), and (3) greater EAS overlap than that provided by the clinical recommendation yielded significant improvements in speech understanding. For standard-electrode CI recipients with preserved hearing, spectral overlap of acoustic and electric stimuli yielded significantly better speech understanding and less listening effort in a laboratory-based, restaurant-noise simulation. In conclusion, EAS patients may derive more benefit from greater acoustic and electric overlap than given in current software fitting recommendations, which are based solely on audiometric threshold. These data have larger scientific implications, as previous studies may not have assessed outcomes with optimized EAS parameters, thereby underestimating the benefit afforded by hearing preservation.

Computer Aided Drafting Packages for Secondary Education. Edition 2. PC DOS Compatible Programs. A MicroSIFT Quarterly Report.

ERIC Educational Resources Information Center

Pollard, Jim

This report reviews eight IBM-compatible software packages that are available to secondary schools to teach computer-aided drafting (CAD). Software packages to be considered were selected following reviews of CAD periodicals, computers in education periodicals, advertisements, and recommendations of teachers. The packages were then rated by…

Spinoff 2013

NASA Technical Reports Server (NTRS)

2014-01-01

Topics covered include: Innovative Software Tools Measure Behavioral Alertness; Miniaturized, Portable Sensors Monitor Metabolic Health; Patient Simulators Train Emergency Caregivers; Solar Refrigerators Store Life-Saving Vaccines; Monitors Enable Medication Management in Patients' Homes; Handheld Diagnostic Device Delivers Quick Medical Readings; Experiments Result in Safer, Spin-Resistant Aircraft; Interfaces Visualize Data for Airline Safety, Efficiency; Data Mining Tools Make Flights Safer, More Efficient; NASA Standards Inform Comfortable Car Seats; Heat Shield Paves the Way for Commercial Space; Air Systems Provide Life Support to Miners; Coatings Preserve Metal, Stone, Tile, and Concrete; Robots Spur Software That Lends a Hand; Cloud-Based Data Sharing Connects Emergency Managers; Catalytic Converters Maintain Air Quality in Mines; NASA-Enhanced Water Bottles Filter Water on the Go; Brainwave Monitoring Software Improves Distracted Minds; Thermal Materials Protect Priceless, Personal Keepsakes; Home Air Purifiers Eradicate Harmful Pathogens; Thermal Materials Drive Professional Apparel Line; Radiant Barriers Save Energy in Buildings; Open Source Initiative Powers Real-Time Data Streams; Shuttle Engine Designs Revolutionize Solar Power; Procedure-Authoring Tool Improves Safety on Oil Rigs; Satellite Data Aid Monitoring of Nation's Forests; Mars Technologies Spawn Durable Wind Turbines; Programs Visualize Earth and Space for Interactive Education; Processor Units Reduce Satellite Construction Costs; Software Accelerates Computing Time for Complex Math; Simulation Tools Prevent Signal Interference on Spacecraft; Software Simplifies the Sharing of Numerical Models; Virtual Machine Language Controls Remote Devices; Micro-Accelerometers Monitor Equipment Health; Reactors Save Energy, Costs for Hydrogen Production; Cameras Monitor Spacecraft Integrity to Prevent Failures; Testing Devices Garner Data on Insulation Performance; Smart Sensors Gather Information for Machine Diagnostics; Oxygen Sensors Monitor Bioreactors and Ensure Health and Safety; Vision Algorithms Catch Defects in Screen Displays; and Deformable Mirrors Capture Exoplanet Data, Reflect Lasers.

Evaluation of MTANNs for eliminating false-positive with different computer aided pulmonary nodules detection software.

PubMed

Shi, Zhenghao; Ma, Jiejue; Feng, Yaning; He, Lifeng; Suzuki, Kenji

2015-11-01

MTANN (Massive Training Artificial Neural Network) is a promising tool, which applied to eliminate false-positive for thoracic CT in recent years. In order to evaluate whether this method is feasible to eliminate false-positive of different CAD schemes, especially, when it is applied to commercial CAD software, this paper evaluate the performance of the method for eliminating false-positives produced by three different versions of commercial CAD software for lung nodules detection in chest radiographs. Experimental results demonstrate that the approach is useful in reducing FPs for different computer aided lung nodules detection software in chest radiographs.

Energy Management of the Multi-Mission Space Exploration Vehicle Using a Goal-Oriented Control System

NASA Technical Reports Server (NTRS)

Braman, Julia M. B.; Wagner, David A.

2010-01-01

Safe human exploration in space missions requires careful management of limited resources such as breathable air and stored electrical energy. Daily activities for astronauts must be carefully planned with respect to such resources, and usage must be monitored as activities proceed to ensure that they can be completed while maintaining safe resource margins. Such planning and monitoring can be complex because they depend on models of resource usage, the activities being planned, and uncertainties. This paper describes a system - and the technology behind it - for energy management of the NASA-Johnson Space Center's Multi-Mission Space Exploration Vehicles (SEV), that provides, in an onboard advisory mode, situational awareness to astronauts and real-time guidance to mission operators. This new capability was evaluated during this year's Desert RATS (Research and Technology Studies) planetary exploration analog test in Arizona. This software aided ground operators and crew members in modifying the day s activities based on the real-time execution of the plan and on energy data received from the rovers.

Computer-Aided Facilities Management Systems (CAFM).

ERIC Educational Resources Information Center

Cyros, Kreon L.

Computer-aided facilities management (CAFM) refers to a collection of software used with increasing frequency by facilities managers. The six major CAFM components are discussed with respect to their usefulness and popularity in facilities management applications: (1) computer-aided design; (2) computer-aided engineering; (3) decision support…

Pilot interaction with automated airborne decision making systems

NASA Technical Reports Server (NTRS)

Rouse, W. B.; Hammer, J. M.; Mitchell, C. M.; Morris, N. M.; Lewis, C. M.; Yoon, W. C.

1985-01-01

Progress was made in the three following areas. In the rule-based modeling area, two papers related to identification and significane testing of rule-based models were presented. In the area of operator aiding, research focused on aiding operators in novel failure situations; a discrete control modeling approach to aiding PLANT operators was developed; and a set of guidelines were developed for implementing automation. In the area of flight simulator hardware and software, the hardware will be completed within two months and initial simulation software will then be integrated and tested.

Software for Teaching about AIDS & Sex: A Critical Review of Products. A MicroSIFT Report.

ERIC Educational Resources Information Center

Weaver, Dave

This document contains critical reviews of 10 microcomputer software packages and two interactive videodisc products designed for use in teaching about Acquired Immune Deficiency Syndrome (AIDS) and sex at the secondary school level and above. Each package was reviewed by one or two secondary school health teachers and by a staff member from the…

A specialized plug-in software module for computer-aided quantitative measurement of medical images.

PubMed

Wang, Q; Zeng, Y J; Huo, P; Hu, J L; Zhang, J H

2003-12-01

This paper presents a specialized system for quantitative measurement of medical images. Using Visual C++, we developed a computer-aided software based on Image-Pro Plus (IPP), a software development platform. When transferred to the hard disk of a computer by an MVPCI-V3A frame grabber, medical images can be automatically processed by our own IPP plug-in for immunohistochemical analysis, cytomorphological measurement and blood vessel segmentation. In 34 clinical studies, the system has shown its high stability, reliability and ease of utility.

Visual and computer software-aided estimates of Dupuytren's contractures: correlation with clinical goniometric measurements.

PubMed

Smith, R P; Dias, J J; Ullah, A; Bhowal, B

2009-05-01

Corrective surgery for Dupuytren's disease represents a significant proportion of a hand surgeon's workload. The decision to go ahead with surgery and the success of surgery requires measuring the degree of contracture of the diseased finger(s). This is performed in clinic with a goniometer, pre- and postoperatively. Monitoring the recurrence of the contracture can inform on surgical outcome, research and audit. We compared visual and computer software-aided estimation of Dupuytren's contractures to clinical goniometric measurements in 60 patients with Dupuytren's disease. Patients' hands were digitally photographed. There were 76 contracted finger joints--70 proximal interphalangeal joints and six distal interphalangeal joints. The degrees of contracture of these images were visually assessed by six orthopaedic staff of differing seniority and re-assessed with computer software. Across assessors, the Pearson correlation between the goniometric measurements and the visual estimations was 0.83 and this significantly improved to 0.88 with computer software. Reliability with intra-class correlations achieved 0.78 and 0.92 for the visual and computer-aided estimations, respectively, and with test-retest analysis, 0.92 for visual estimation and 0.95 for computer-aided measurements. Visual estimations of Dupuytren's contractures correlate well with actual clinical goniometric measurements and improve further if measured with computer software. Digital images permit monitoring of contracture after surgery and may facilitate research into disease progression and auditing of surgical technique.

Software Engineering Laboratory (SEL) compendium of tools, revision 1

NASA Technical Reports Server (NTRS)

1982-01-01

A set of programs used to aid software product development is listed. Known as software tools, such programs include requirements analyzers, design languages, precompilers, code auditors, code analyzers, and software librarians. Abstracts, resource requirements, documentation, processing summaries, and availability are indicated for most tools.

Automatic extraction and visualization of object-oriented software design metrics

NASA Astrophysics Data System (ADS)

Lakshminarayana, Anuradha; Newman, Timothy S.; Li, Wei; Talburt, John

2000-02-01

Software visualization is a graphical representation of software characteristics and behavior. Certain modes of software visualization can be useful in isolating problems and identifying unanticipated behavior. In this paper we present a new approach to aid understanding of object- oriented software through 3D visualization of software metrics that can be extracted from the design phase of software development. The focus of the paper is a metric extraction method and a new collection of glyphs for multi- dimensional metric visualization. Our approach utilize the extensibility interface of a popular CASE tool to access and automatically extract the metrics from Unified Modeling Language class diagrams. Following the extraction of the design metrics, 3D visualization of these metrics are generated for each class in the design, utilizing intuitively meaningful 3D glyphs that are representative of the ensemble of metrics. Extraction and visualization of design metrics can aid software developers in the early study and understanding of design complexity.

SUNREL Energy Simulation Software | Buildings | NREL

Science.gov Websites

SUNREL Energy Simulation Software SUNREL Energy Simulation Software SUNREL® is a hourly building energy simulation program that aids in the design of small energy-efficient buildings where the loads are

Systems design and comparative analysis of large antenna concepts

NASA Technical Reports Server (NTRS)

Garrett, L. B.; Ferebee, M. J., Jr.

1983-01-01

Conceptual designs are evaluated and comparative analyses conducted for several large antenna spacecraft for Land Mobile Satellite System (LMSS) communications missions. Structural configurations include trusses, hoop and column and radial rib. The study was conducted using the Interactive Design and Evaluation of Advanced Spacecraft (IDEAS) system. The current capabilities, development status, and near-term plans for the IDEAS system are reviewed. Overall capabilities are highlighted. IDEAS is an integrated system of computer-aided design and analysis software used to rapidly evaluate system concepts and technology needs for future advanced spacecraft such as large antennas, platforms, and space stations. The system was developed at Langley to meet a need for rapid, cost-effective, labor-saving approaches to the design and analysis of numerous missions and total spacecraft system options under consideration. IDEAS consists of about 40 technical modules efficient executive, data-base and file management software, and interactive graphics display capabilities.

Rule groupings: An approach towards verification of expert systems

NASA Technical Reports Server (NTRS)

Mehrotra, Mala

1991-01-01

Knowledge-based expert systems are playing an increasingly important role in NASA space and aircraft systems. However, many of NASA's software applications are life- or mission-critical and knowledge-based systems do not lend themselves to the traditional verification and validation techniques for highly reliable software. Rule-based systems lack the control abstractions found in procedural languages. Hence, it is difficult to verify or maintain such systems. Our goal is to automatically structure a rule-based system into a set of rule-groups having a well-defined interface to other rule-groups. Once a rule base is decomposed into such 'firewalled' units, studying the interactions between rules would become more tractable. Verification-aid tools can then be developed to test the behavior of each such rule-group. Furthermore, the interactions between rule-groups can be studied in a manner similar to integration testing. Such efforts will go a long way towards increasing our confidence in the expert-system software. Our research efforts address the feasibility of automating the identification of rule groups, in order to decompose the rule base into a number of meaningful units.

Current And Future Directions Of Lens Design Software

NASA Astrophysics Data System (ADS)

Gustafson, Darryl E.

1983-10-01

The most effective environment for doing lens design continues to evolve as new computer hardware and software tools become available. Important recent hardware developments include: Low-cost but powerful interactive multi-user 32 bit computers with virtual memory that are totally software-compatible with prior larger and more expensive members of the family. A rapidly growing variety of graphics devices for both hard-copy and screen graphics, including many with color capability. In addition, with optical design software readily accessible in many forms, optical design has become a part-time activity for a large number of engineers instead of being restricted to a small number of full-time specialists. A designer interface that is friendly for the part-time user while remaining efficient for the full-time designer is thus becoming more important as well as more practical. Along with these developments, software tools in other scientific and engineering disciplines are proliferating. Thus, the optical designer is less and less unique in his use of computer-aided techniques and faces the challenge and opportunity of efficiently communicating his designs to other computer-aided-design (CAD), computer-aided-manufacturing (CAM), structural, thermal, and mechanical software tools. This paper will address the impact of these developments on the current and future directions of the CODE VTM optical design software package, its implementation, and the resulting lens design environment.

Application of CT-PSF-based computer-simulated lung nodules for evaluating the accuracy of computer-aided volumetry.

PubMed

Funaki, Ayumu; Ohkubo, Masaki; Wada, Shinichi; Murao, Kohei; Matsumoto, Toru; Niizuma, Shinji

2012-07-01

With the wide dissemination of computed tomography (CT) screening for lung cancer, measuring the nodule volume accurately with computer-aided volumetry software is increasingly important. Many studies for determining the accuracy of volumetry software have been performed using a phantom with artificial nodules. These phantom studies are limited, however, in their ability to reproduce the nodules both accurately and in the variety of sizes and densities required. Therefore, we propose a new approach of using computer-simulated nodules based on the point spread function measured in a CT system. The validity of the proposed method was confirmed by the excellent agreement obtained between computer-simulated nodules and phantom nodules regarding the volume measurements. A practical clinical evaluation of the accuracy of volumetry software was achieved by adding simulated nodules onto clinical lung images, including noise and artifacts. The tested volumetry software was revealed to be accurate within an error of 20 % for nodules >5 mm and with the difference between nodule density and background (lung) (CT value) being 400-600 HU. Such a detailed analysis can provide clinically useful information on the use of volumetry software in CT screening for lung cancer. We concluded that the proposed method is effective for evaluating the performance of computer-aided volumetry software.

AF-GEOSPACE Version 2.1

NASA Astrophysics Data System (ADS)

Hilmer, R. V.; Ginet, G. P.; Hall, T.; Holeman, E.; Madden, D.; Tautz, M.; Roth, C.

2004-05-01

AF-GEOSpace is a graphics-intensive software program with space environment models and applications developed and distributed by the Space Weather Center of Excellence at AFRL. A review of current (Version 2.0) and planned (Version 2.1) AF-GEOSpace capabilities will be given. A wide range of physical domains is represented enabling the software to address such things as solar disturbance propagation, radiation belt configuration, and ionospheric auroral particle precipitation and scintillation. The software is currently being used to aid with the design, operation, and simulation of a wide variety of communications, navigation, and surveillance systems. Building on the success of previous releases, AF-GEOSpace has become a platform for the rapid prototyping of automated operational and simulation space weather visualization products and helps with a variety of tasks, including: orbit specification for radiation hazard avoidance; satellite design assessment and post-event anomaly analysis; solar disturbance effects forecasting; frequency and antenna management for radar and HF communications; determination of link outage regions for active ionospheric conditions; scientific model validation and comparison, physics research, and education. Version 2.0 provided a simplified graphical user interface, improved science and application modules, and significantly enhanced graphical performance. Common input data archive sets, application modules, and 1-D, 2-D, and 3-D visualization tools are provided to all models. Dynamic capabilities permit multiple environments to be generated at user-specified time intervals while animation tools enable displays such as satellite orbits and environment data together as a function of time. Building on the existing Version 2.0 software architecture, AF-GEOSpace Version 2.1 is currently under development and will include a host of new modules to provide, for example, geosynchronous charged particle fluxes, neutral atmosphere densities, cosmic ray cutoff maps, low-altitude trapped proton belt specification, and meteor shower/storm fluxes with spacecraft impact probabilities. AF-GEOSpace Version 2.1 is being developed for Windows NT/2000/XP and Linux systems.

21 CFR 882.1440 - Neuropsychiatric interpretive electroencephalograph assessment aid.

Code of Federal Regulations, 2014 CFR

2014-04-01

... described in detail in the software requirements specification and software design specification... the device, hardware and software, must be fully characterized and must demonstrate a reasonable assurance of safety and effectiveness. (i) Hardware specifications must be provided. Appropriate...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kirby, M.J.; Kramer, S.R.; Pittard, G.T.

Jason Consultants International, Inc., under the sponsorship of the Gas Research Institute (GRI), has developed guidelines, procedures and software, which are described in this paper, for the installation of polyethylene gas pipe using guided horizontal drilling. Jason was aided in this development by two key subcontractors; Maurer Engineering who wrote the software and NICOR Technologies who reviewed the software and guidelines from a utility perspective. This program resulted in the development of commerically viable software for utilities, contractors, engineering firms, and others involved with the installation of pipes using guided horizontal drilling. The software is an interactive design tool thatmore » allows the user to enter ground elevation data, alignment information and pipe data. The software aides the engineer in designing a drill path and provides plan and profile views along with tabular data for pipe depth and surface profile. Finally, the software calculates installation loads and pipe stresses, compares these values against pipe manufacturer`s recommendations, and provides this information graphically and in tabular form. 5 refs., 18 figs., 2 tabs.« less

Aspects on Transfer of Aided - Design Files

NASA Astrophysics Data System (ADS)

Goanta, A. M.; Anghelache, D. G.

2016-08-01

At this stage of development of hardware and software, each company that makes design software packages has a certain type of file created and customized in time to distinguish that company from its competitors. Thus today are widely known the DWG files belonging AutoCAD, IPT / IAM belonging to Inventor, PAR / ASM of Solid Edge's, PRT from the NX and so on. Behind every type of file there is a mathematical model which is common to more types of files. A specific aspect of the computer -aided design is that all softwares are working with both individual parts and assemblies, but their approach is different in that some use the same type of file both for each part and for the whole (PRT ), while others use different types of files (IPT / IAM, PAR / ASM, etc.). Another aspect of the computer -aided design is to transfer files between different companies which use different software packages or even the same software package but in different versions. Each of these situations generates distinct issues. Thus, to solve the partial reading by a project different from the native one, transfer files of STEP and IGES type are used

Space power system scheduling using an expert system

NASA Technical Reports Server (NTRS)

Bahrami, K. A.; Biefeld, E.; Costello, L.; Klein, J. W.

1986-01-01

A most pressing problem in space exploration is timely spacecraft power system sequence generation, which requires the scheduling of a set of loads given a set of resource constraints. This is particularly important after an anomaly or failure. This paper discusses the power scheduling problem and how the software program, Plan-It, can be used as a consultant for scheduling power system activities. Modeling of power activities, human interface, and two of the many strategies used by Plan-It are discussed. Preliminary results showing the development of a conflict-free sequence from an initial sequence with conflicts is presented. It shows that a 4-day schedule can be generated in a matter of a few minutes, which provides sufficient time in many cases to aid the crew in the replanning of loads and generation use following a failure or anomaly.

Using CASE Software to Teach Undergraduates Systems Analysis and Design.

ERIC Educational Resources Information Center

Wilcox, Russell E.

1988-01-01

Describes the design and delivery of a college course for information system students utilizing a Computer-Aided Software Engineering program. Discusses class assignments, cooperative learning, student attitudes, and the advantages of using this software in the course. (CW)

The Software Line-up: What Reviewers Look for When Evaluating Software.

ERIC Educational Resources Information Center

ELECTRONIC Learning, 1982

1982-01-01

Contains a check list to aid teachers in evaluating software used in computer-assisted instruction on microcomputers. The evaluation form contains three sections: program description, program evaluation, and overall evaluation. A brief description of a software evaluation program in use at the Granite School District in Utah is included. (JJD)

Tips on Creating Complex Geometry Using Solid Modeling Software

ERIC Educational Resources Information Center

Gow, George

2008-01-01

Three-dimensional computer-aided drafting (CAD) software, sometimes referred to as "solid modeling" software, is easy to learn, fun to use, and becoming the standard in industry. However, many users have difficulty creating complex geometry with the solid modeling software. And the problem is not entirely a student problem. Even some teachers and…

Human Motion Tracking and Glove-Based User Interfaces for Virtual Environments in ANVIL

NASA Technical Reports Server (NTRS)

Dumas, Joseph D., II

2002-01-01

The Army/NASA Virtual Innovations Laboratory (ANVIL) at Marshall Space Flight Center (MSFC) provides an environment where engineers and other personnel can investigate novel applications of computer simulation and Virtual Reality (VR) technologies. Among the many hardware and software resources in ANVIL are several high-performance Silicon Graphics computer systems and a number of commercial software packages, such as Division MockUp by Parametric Technology Corporation (PTC) and Jack by Unigraphics Solutions, Inc. These hardware and software platforms are used in conjunction with various VR peripheral I/O (input / output) devices, CAD (computer aided design) models, etc. to support the objectives of the MSFC Engineering Systems Department/Systems Engineering Support Group (ED42) by studying engineering designs, chiefly from the standpoint of human factors and ergonomics. One of the more time-consuming tasks facing ANVIL personnel involves the testing and evaluation of peripheral I/O devices and the integration of new devices with existing hardware and software platforms. Another important challenge is the development of innovative user interfaces to allow efficient, intuitive interaction between simulation users and the virtual environments they are investigating. As part of his Summer Faculty Fellowship, the author was tasked with verifying the operation of some recently acquired peripheral interface devices and developing new, easy-to-use interfaces that could be used with existing VR hardware and software to better support ANVIL projects.

Space Station Software Recommendations

NASA Technical Reports Server (NTRS)

Voigt, S. (Editor)

1985-01-01

Four panels of invited experts and NASA representatives focused on the following topics: software management, software development environment, languages, and software standards. Each panel deliberated in private, held two open sessions with audience participation, and developed recommendations for the NASA Space Station Program. The major thrusts of the recommendations were as follows: (1) The software management plan should establish policies, responsibilities, and decision points for software acquisition; (2) NASA should furnish a uniform modular software support environment and require its use for all space station software acquired (or developed); (3) The language Ada should be selected for space station software, and NASA should begin to address issues related to the effective use of Ada; and (4) The space station software standards should be selected (based upon existing standards where possible), and an organization should be identified to promulgate and enforce them. These and related recommendations are described in detail in the conference proceedings.

Space Station Software Issues

NASA Technical Reports Server (NTRS)

Voigt, S. (Editor); Beskenis, S. (Editor)

1985-01-01

Issues in the development of software for the Space Station are discussed. Software acquisition and management, software development environment, standards, information system support for software developers, and a future software advisory board are addressed.

Operator Station Design System - A computer aided design approach to work station layout

NASA Technical Reports Server (NTRS)

Lewis, J. L.

1979-01-01

The Operator Station Design System is resident in NASA's Johnson Space Center Spacecraft Design Division Performance Laboratory. It includes stand-alone minicomputer hardware and Panel Layout Automated Interactive Design and Crew Station Assessment of Reach software. The data base consists of the Shuttle Transportation System Orbiter Crew Compartment (in part), the Orbiter payload bay and remote manipulator (in part), and various anthropometric populations. The system is utilized to provide panel layouts, assess reach and vision, determine interference and fit problems early in the design phase, study design applications as a function of anthropometric and mission requirements, and to accomplish conceptual design to support advanced study efforts.

Development of a prototype commonality analysis tool for use in space programs

NASA Technical Reports Server (NTRS)

Yeager, Dorian P.

1988-01-01

A software tool to aid in performing commonality analyses, called Commonality Analysis Problem Solver (CAPS), was designed, and a prototype version (CAPS 1.0) was implemented and tested. The CAPS 1.0 runs in an MS-DOS or IBM PC-DOS environment. The CAPS is designed around a simple input language which provides a natural syntax for the description of feasibility constraints. It provides its users with the ability to load a database representing a set of design items, describe the feasibility constraints on items in that database, and do a comprehensive cost analysis to find the most economical substitution pattern.

Program Helps Decompose Complex Design Systems

NASA Technical Reports Server (NTRS)

Rogers, James L., Jr.; Hall, Laura E.

1995-01-01

DeMAID (Design Manager's Aid for Intelligent Decomposition) computer program is knowledge-based software system for ordering sequence of modules and identifying possible multilevel structure for design problems such as large platforms in outer space. Groups modular subsystems on basis of interactions among them. Saves considerable amount of money and time in total design process, particularly in new design problem in which order of modules has not been defined. Originally written for design problems, also applicable to problems containing modules (processes) that take inputs and generate outputs. Available in three machine versions: Macintosh written in Symantec's Think C 3.01, Sun, and SGI IRIS in C language.

Advanced decision aiding techniques applicable to space

NASA Technical Reports Server (NTRS)

Kruchten, Robert J.

1987-01-01

RADC has had an intensive program to show the feasibility of applying advanced technology to Air Force decision aiding situations. Some aspects of the program, such as Satellite Autonomy, are directly applicable to space systems. For example, RADC has shown the feasibility of decision aids that combine the advantages of laser disks and computer generated graphics; decision aids that interface object-oriented programs with expert systems; decision aids that solve path optimization problems; etc. Some of the key techniques that could be used in space applications are reviewed. Current applications are reviewed along with their advantages and disadvantages, and examples are given of possible space applications. The emphasis is to share RADC experience in decision aiding techniques.

Selecting Really Excellent Software for Young Adults.

ERIC Educational Resources Information Center

Polly, Jean Armour

1985-01-01

This article discusses criteria of a good computer software package to aid the public librarian in the building, weeding, and maintenance of a software collection for young adults. Highlights include manuals or documentation; bells, whistles, and color; and the true test of time. (EJS)

CAMEO

EPA Pesticide Factsheets

This resource directory offers easier access to the CAMEO suite of software. CAMEO, Computer-Aided Management of Emergency Operations, is system of software applications used to plan for and respond to chemical emergencies.

Developing hybrid near-space technologies for affordable access to suborbital space

NASA Astrophysics Data System (ADS)

Badders, Brian David

High power rockets and high altitude balloons are two near-space technologies that could be combined in order to provide access to the mesosphere and, eventually, suborbital space. This "rockoon" technology has been used by several large budget space programs before being abandoned in favor of even more expensive, albeit more accurate, ground launch systems. With the increased development of nano-satellites and atmospheric sensors, combined with rising interest in global atmospheric data, there is an increase in desire for affordable access to extreme altitudes that does not necessarily require the precision of ground launches. Development of hybrid near-space technologies for access to over 200k ft. on a small budget brings many challenges within engineering, systems integration, cost analysis, market analysis, and business planning. This research includes the design and simulation testing of all the systems needed for a safe and reusable launch system, the cost analysis for initial production, the development of a business plan, and the development of a marketing plan. This project has both engineering and scientific significance in that it can prove the space readiness of new technologies, raise their technology readiness levels (TRLs), expedite the development process, and also provide new data to the scientific community. It also has the ability to stimulate university involvement in the aerospace industry and help to inspire the next generation of workers in the space sector. Previous development of high altitude balloon/high power rocket hybrid systems have been undertaken by government funded military programs or large aerospace corporations with varying degrees of success. However, there has yet to be a successful flight with this type of system which provides access to the upper mesosphere in a university setting. This project will aim to design and analyze a viable system while testing the engineering process under challenging budgetary constraints. The technical, engineering, and systems integration challenges that will be investigated are rocket design, launch platform design, communications, ignition systems, recovery systems, and stabilization methods. This will be done using rocket performance simulation software, computer-aided design software, and computational fluid dynamic analysis software. The business planning is also an important part of this research. Through detailed market analysis, the needs for the proposed product/services being developed will be assessed. Through the combination of detailed cost analysis and the market needs, the economic viability of this launch system will be determined.

Computer-Aided Process and Tools for Mobile Software Acquisition

DTIC Science & Technology

2013-07-30

moldo^j= pmlkploba=obmloq=pbofbp= Computer-Aided Process and Tools for Mobile Software Acquisition 30 July 2013 LT Christopher Bonine , USN, Dr...Christopher Bonine is a lieutenant in the United States Navy. He is currently assigned to the Navy Cyber Defense Operations Command in Norfolk, VA. He has...interests are in development and implementation of cyber security policy. Bonine has a master’s in computer science from the Naval Postgraduate School

Specification for Visual Requirements of Work-Centered Software Systems

DTIC Science & Technology

2006-10-01

no person shall be subject to any penity for fallng to comply wih a collection of N ilo ration it does not display a currenty valid OMB control...work- aiding systems. Based on the design concept for a work- centered support system (WCSS), these software systems support user tasks and goals...through both direct and indirect aiding methods within the interface client. In order to ensure the coherent development and delivery of work- centered

Implementation of Audio Computer-Assisted Interviewing Software in HIV/AIDS Research

PubMed Central

Pluhar, Erika; Yeager, Katherine A.; Corkran, Carol; McCarty, Frances; Holstad, Marcia McDonnell; Denzmore-Nwagbara, Pamela; Fielder, Bridget; DiIorio, Colleen

2007-01-01

Computer assisted interviewing (CAI) has begun to play a more prominent role in HIV/AIDS prevention research. Despite the increased popularity of CAI, particularly audio computer assisted self-interviewing (ACASI), some research teams are still reluctant to implement ACASI technology due to lack of familiarity with the practical issues related to using these software packages. The purpose of this paper is to describe the implementation of one particular ACASI software package, the Questionnaire Development System™ (QDS™), in several nursing and HIV/AIDS prevention research settings. We present acceptability and satisfaction data from two large-scale public health studies in which we have used QDS with diverse populations. We also address issues related to developing and programming a questionnaire, discuss practical strategies related to planning for and implementing ACASI in the field, including selecting equipment, training staff, and collecting and transferring data, and summarize advantages and disadvantages of computer assisted research methods. PMID:17662924

An Architecture, System Engineering, and Acquisition Approach for Space System Software Resiliency

NASA Astrophysics Data System (ADS)

Phillips, Dewanne Marie

Software intensive space systems can harbor defects and vulnerabilities that may enable external adversaries or malicious insiders to disrupt or disable system functions, risking mission compromise or loss. Mitigating this risk demands a sustained focus on the security and resiliency of the system architecture including software, hardware, and other components. Robust software engineering practices contribute to the foundation of a resilient system so that the system "can take a hit to a critical component and recover in a known, bounded, and generally acceptable period of time". Software resiliency must be a priority and addressed early in the life cycle development to contribute a secure and dependable space system. Those who develop, implement, and operate software intensive space systems must determine the factors and systems engineering practices to address when investing in software resiliency. This dissertation offers methodical approaches for improving space system resiliency through software architecture design, system engineering, increased software security, thereby reducing the risk of latent software defects and vulnerabilities. By providing greater attention to the early life cycle phases of development, we can alter the engineering process to help detect, eliminate, and avoid vulnerabilities before space systems are delivered. To achieve this objective, this dissertation will identify knowledge, techniques, and tools that engineers and managers can utilize to help them recognize how vulnerabilities are produced and discovered so that they can learn to circumvent them in future efforts. We conducted a systematic review of existing architectural practices, standards, security and coding practices, various threats, defects, and vulnerabilities that impact space systems from hundreds of relevant publications and interviews of subject matter experts. We expanded on the system-level body of knowledge for resiliency and identified a new software architecture framework and acquisition methodology to improve the resiliency of space systems from a software perspective with an emphasis on the early phases of the systems engineering life cycle. This methodology involves seven steps: 1) Define technical resiliency requirements, 1a) Identify standards/policy for software resiliency, 2) Develop a request for proposal (RFP)/statement of work (SOW) for resilient space systems software, 3) Define software resiliency goals for space systems, 4) Establish software resiliency quality attributes, 5) Perform architectural tradeoffs and identify risks, 6) Conduct architecture assessments as part of the procurement process, and 7) Ascertain space system software architecture resiliency metrics. Data illustrates that software vulnerabilities can lead to opportunities for malicious cyber activities, which could degrade the space mission capability for the user community. Reducing the number of vulnerabilities by improving architecture and software system engineering practices can contribute to making space systems more resilient. Since cyber-attacks are enabled by shortfalls in software, robust software engineering practices and an architectural design are foundational to resiliency, which is a quality that allows the system to "take a hit to a critical component and recover in a known, bounded, and generally acceptable period of time". To achieve software resiliency for space systems, acquirers and suppliers must identify relevant factors and systems engineering practices to apply across the lifecycle, in software requirements analysis, architecture development, design, implementation, verification and validation, and maintenance phases.

78 FR 68861 - Certain Navigation Products, Including GPS Devices, Navigation and Display Systems, Radar Systems...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-15

... Devices, Navigation and Display Systems, Radar Systems, Navigational Aids, Mapping Systems and Related... navigation products, including GPS devices, navigation and display systems, radar systems, navigational aids..., radar systems, navigational aids, mapping systems and related software by reason of infringement of one...

Computer Aided Creativity.

ERIC Educational Resources Information Center

Proctor, Tony

1988-01-01

Explores the conceptual components of a computer program designed to enhance creative thinking and reviews software that aims to stimulate creative thinking. Discusses BRAIN and ORACLE, programs intended to aid in creative problem solving. (JOW)

Development of a Cross-Flow Fan Rotor for Vertical Take-Off and Landing Aircraft

DTIC Science & Technology

2013-06-01

ANSYS CFX , along with the commercial computer-aided design software SolidWorks, was used to model and perform a parametric study on the number of rotor...the results found using ANSYS CFX . The experimental and analytical models were successfully compared at speeds ranging from 4,000 to 7,000 RPM...will make vertical take-off possible. The commercial computational fluid dynamics software ANSYS CFX , along with the commercial computer-aided design

Improved Foundry Castings Utilizing CAD/CAM (Computer Aided Design/ Computer Aided Manufacture). Volume 1. Overview

DTIC Science & Technology

1988-06-30

casting. 68 Figure 1-9: Line printer representation of roll solidification. 69 Figure I1-1: Test casting model. 76 Figure 11-2: Division of test casting...writing new casting analysis and design routines. The new routines would take advantage of advanced criteria for predicting casting soundness and cast...properties and technical advances in computer hardware and software. 11 2. CONCLUSIONS UPCAST, a comprehensive software package, has been developed for

Computer-aided navigation in dental implantology: 7 years of clinical experience.

PubMed

Ewers, Rolf; Schicho, Kurt; Truppe, Michael; Seemann, Rudolf; Reichwein, Astrid; Figl, Michael; Wagner, Arne

2004-03-01

This long-term study gives a review over 7 years of research, development, and routine clinical application of computer-aided navigation technology in dental implantology. Benefits and disadvantages of up-to-date technologies are discussed. In the course of the current advancement, various hardware and software configurations are used. In the initial phase, universally applicable navigation software is adapted for implantology. Since 2001, a special software module for dental implantology is available. Preoperative planning is performed on the basis of prosthetic aspects and requirements. In clinical routine use, patient and drill positions are intraoperatively registered by means of optoelectronic tracking systems; during preclinical tests, electromagnetic trackers are also used. In 7 years (1995 to 2002), 55 patients with 327 dental implants were successfully positioned with computer-aided navigation technology. The mean number of implants per patient was 6 (minimum, 1; maximum, 11). No complications were observed; the preoperative planning could be exactly realized. The average expenditure of time for the preparation of a surgical intervention with navigation decreased from 2 to 3 days in the initial phase to one-half day in clinical routine use with software that is optimized for dental implantology. The use of computer-aided navigation technology can contribute to considerable quality improvement. Preoperative planning is exactly realized and intraoperative safety is increased, because damage to nerves or neighboring teeth can be avoided.

Development of Improved Software Intelligent System for Audiological Solutions.

PubMed

Rajkumar, S; Muttan, S; Sapthagirivasan, V; Jaya, V; Vignesh, S S

2018-06-02

Of late, there has been an increase in hearing impairment cases and to provide the most advantageous solutions to them is an uphill task for audiologists. Significant difficulty faced by the audiologists is in effective programming of hearing aids to provide enhanced satisfaction to the users. The main aim of our study was to develop a software intelligent system (SIS): (i) to perform the required audiological investigations for finding the degree and type of hearing loss, and (ii) to suggest appropriate values of hearing aid parameters for enhancing the speech intelligibility and the satisfaction level among the hearing aid users. In this paper, we present a Neuro-Fuzzy based SIS to automatically predict and suggest the hearing-aid parameters such as gain values, compression ratio and threshold knee point, which are needed to be fixed for different octave frequencies of sound inputs during the hearing-aid trial. The test signals for audiological investigations are generated through the standard hardware present in a personal computer system and with the aid of a software algorithm. The proposed system was validated with 243 subjects' data collected at the Government General Hospital, Chennai, India. The calculated sensitivity, specificity and accuracy of the proposed audiometer incorporated in the SIS were 98.6%, 96.4 and 98.2%, respectively, by comparing its interpretations with those of the 'gold standard' audiometers. Furthermore, 91% (221 of 243) of the hearing impaired subjects attained satisfaction in the first hearing aid trials itself with the gain values as recommended by the improved SIS. The proposed system reduced around 75% of the 'trial and error' time spent by audiologists for enhancing satisfactory usage of the hearing aid. Hence, the proposed SIS could be used to find the degree and type of hearing loss and to recommend hearing aid parameters to provide optimal solutions to the hearing aid users.

An assessment of space shuttle flight software development processes

NASA Technical Reports Server (NTRS)

1993-01-01

In early 1991, the National Aeronautics and Space Administration's (NASA's) Office of Space Flight commissioned the Aeronautics and Space Engineering Board (ASEB) of the National Research Council (NRC) to investigate the adequacy of the current process by which NASA develops and verifies changes and updates to the Space Shuttle flight software. The Committee for Review of Oversight Mechanisms for Space Shuttle Flight Software Processes was convened in Jan. 1992 to accomplish the following tasks: (1) review the entire flight software development process from the initial requirements definition phase to final implementation, including object code build and final machine loading; (2) review and critique NASA's independent verification and validation process and mechanisms, including NASA's established software development and testing standards; (3) determine the acceptability and adequacy of the complete flight software development process, including the embedded validation and verification processes through comparison with (1) generally accepted industry practices, and (2) generally accepted Department of Defense and/or other government practices (comparing NASA's program with organizations and projects having similar volumes of software development, software maturity, complexity, criticality, lines of code, and national standards); (4) consider whether independent verification and validation should continue. An overview of the study, independent verification and validation of critical software, and the Space Shuttle flight software development process are addressed. Findings and recommendations are presented.

Virtual manufacturing work cell for engineering

NASA Astrophysics Data System (ADS)

Watanabe, Hideo; Ohashi, Kazushi; Takahashi, Nobuyuki; Kato, Kiyotaka; Fujita, Satoru

1997-12-01

The life cycles of products have been getting shorter. To meet this rapid turnover, manufacturing systems must be frequently changed as well. In engineering to develop manufacturing systems, there are several tasks such as process planning, layout design, programming, and final testing using actual machines. This development of manufacturing systems takes a long time and is expensive. To aid the above engineering process, we have developed the virtual manufacturing workcell (VMW). This paper describes a concept of VMW and design method through computer aided manufacturing engineering using VMW (CAME-VMW) related to the above engineering tasks. The VMW has all design data, and realizes a behavior of equipment and devices using a simulator. The simulator has logical and physical functionality. The one simulates a sequence control and the other simulates motion control, shape movement in 3D space. The simulator can execute the same control software made for actual machines. Therefore we can verify the behavior precisely before the manufacturing workcell will be constructed. The VMW creates engineering work space for several engineers and offers debugging tools such as virtual equipment and virtual controllers. We applied this VMW to development of a transfer workcell for vaporization machine in actual manufacturing system to produce plasma display panel (PDP) workcell and confirmed its effectiveness.

A comparison of vowel productions in prelingually deaf children using cochlear implants, severe hearing-impaired children using conventional hearing aids and normal-hearing children.

PubMed

Baudonck, Nele; Van Lierde, K; Dhooge, I; Corthals, P

2011-01-01

The purpose of this study was to compare vowel productions by deaf cochlear implant (CI) children, hearing-impaired hearing aid (HA) children and normal-hearing (NH) children. 73 children [mean age: 9;14 years (years;months)] participated: 40 deaf CI children, 34 moderately to profoundly hearing-impaired HA children and 42 NH children. For the 3 corner vowels [a], [i] and [u], F(1), F(2) and the intrasubject SD were measured using the Praat software. Spectral separation between these vowel formants and vowel space were calculated. The significant effects in the CI group all pertain to a higher intrasubject variability in formant values, whereas the significant effects in the HA group all pertain to lower formant values. Both hearing-impaired subgroups showed a tendency toward greater intervowel distances and vowel space. Several subtle deviations in the vowel production of deaf CI children and hearing-impaired HA children could be established, using a well-defined acoustic analysis. CI children as well as HA children in this study tended to overarticulate, which hypothetically can be explained by a lack of auditory feedback and an attempt to compensate it by proprioceptive feedback during articulatory maneuvers. Copyright © 2010 S. Karger AG, Basel.

Experimenting Maintenance of Flight Software in an Integrated Modular Avionics for Space

NASA Astrophysics Data System (ADS)

Hardy, Johan; Laroche, Thomas; Creten, Philippe; Parisis, Paul; Hiller, Martin

2014-08-01

This paper presents an experiment of Flight Software partitioning in an Integrated Modular Avionics for Space (IMA-SP) system. This experiment also tackles the maintenance aspects of IMA-SP systems. The presented case study is PROBA-2 Flight Software. The paper addresses and discusses the following subjects: On-Board Software Maintenance in IMA- SP, boot strategy for Time and Space Partitioning, considerations about the ground segment related to On-Board Software Maintenance in IMA-SP, and architectural impacts of Time and Space Partitioning for PROBA software's. Finally, this paper presents the results and the achievements of the study and it appeals at further perspectives for IMA-SP and Time and Space Partitioning.

NASA space station software standards issues

NASA Technical Reports Server (NTRS)

Tice, G. D., Jr.

1985-01-01

The selection and application of software standards present the NASA Space Station Program with the opportunity to serve as a pacesetter for the United States software in the area of software standards. The strengths and weaknesses of each of the NASA defined software standards issues are summerized and discussed. Several significant standards issues are offered for NASA consideration. A challenge is presented for the NASA Space Station Program to serve as a pacesetter for the U.S. Software Industry through: (1) Management commitment to software standards; (2) Overall program participation in software standards; and (3) Employment of the best available technology to support software standards

Design of an air traffic computer simulation system to support investigation of civil tiltrotor aircraft operations

NASA Technical Reports Server (NTRS)

Rogers, Ralph V.

1993-01-01

The TATSS Project's goal was to develop a design for computer software that would support the attainment of the following objectives for the air traffic simulation model: (1) Full freedom of movement for each aircraft object in the simulation model. Each aircraft object may follow any designated flight plan or flight path necessary as required by the experiment under consideration. (2) Object position precision up to +/- 3 meters vertically and +/- 15 meters horizontally. (3) Aircraft maneuvering in three space with the object position precision identified above. (4) Air traffic control operations and procedures. (5) Radar, communication, navaid, and landing aid performance. (6) Weather. (7) Ground obstructions and terrain. (8) Detection and recording of separation violations. (9) Measures of performance including deviations from flight plans, air space violations, air traffic control messages per aircraft, and traditional temporal based measures.

Real-time remote scientific model validation

NASA Technical Reports Server (NTRS)

Frainier, Richard; Groleau, Nicolas

1994-01-01

This paper describes flight results from the use of a CLIPS-based validation facility to compare analyzed data from a space life sciences (SLS) experiment to an investigator's preflight model. The comparison, performed in real-time, either confirms or refutes the model and its predictions. This result then becomes the basis for continuing or modifying the investigator's experiment protocol. Typically, neither the astronaut crew in Spacelab nor the ground-based investigator team are able to react to their experiment data in real time. This facility, part of a larger science advisor system called Principal Investigator in a Box, was flown on the space shuttle in October, 1993. The software system aided the conduct of a human vestibular physiology experiment and was able to outperform humans in the tasks of data integrity assurance, data analysis, and scientific model validation. Of twelve preflight hypotheses associated with investigator's model, seven were confirmed and five were rejected or compromised.

Orbit Determination and Navigation of the Solar Terrestrial Relations Observatory (STEREO)

NASA Technical Reports Server (NTRS)

Mesarch, Michael A.; Robertson, Mika; Ottenstein, Neil; Nicholson, Ann; Nicholson, Mark; Ward, Douglas T.; Cosgrove, Jennifer; German, Darla; Hendry, Stephen; Shaw, James

2007-01-01

This paper provides an overview of the required upgrades necessary for navigation of NASA's twin heliocentric science missions, Solar TErestrial RElations Observatory (STEREO) Ahead and Behind. The orbit determination of the STEREO spacecraft was provided by the NASA Goddard Space Flight Center's (GSFC) Flight Dynamics Facility (FDF) in support of the mission operations activities performed by the Johns Hopkins University Applied Physics Laboratory (APL). The changes to FDF's orbit determination software included modeling upgrades as well as modifications required to process the Deep Space Network X-band tracking data used for STEREO. Orbit results as well as comparisons to independently computed solutions are also included. The successful orbit determination support aided in maneuvering the STEREO spacecraft, launched on October 26, 2006 (00:52 Z), to target the lunar gravity assists required to place the spacecraft into their final heliocentric drift-away orbits where they are providing stereo imaging of the Sun.

Orbit Determination and Navigation of the Solar Terrestrial Relations Observatory (STEREO)

NASA Technical Reports Server (NTRS)

Mesarch, Michael; Robertson, Mika; Ottenstein, Neil; Nicholson, Ann; Nicholson, Mark; Ward, Douglas T.; Cosgrove, Jennifer; German, Darla; Hendry, Stephen; Shaw, James

2007-01-01

This paper provides an overview of the required upgrades necessary for navigation of NASA's twin heliocentric science missions, Solar TErestrial RElations Observatory (STEREO) Ahead and Behind. The orbit determination of the STEREO spacecraft was provided by the NASA Goddard Space Flight Center's (GSFC) Flight Dynamics Facility (FDF) in support of the mission operations activities performed by the Johns Hopkins University Applied Physics Laboratory (APL). The changes to FDF s orbit determination software included modeling upgrades as well as modifications required to process the Deep Space Network X-band tracking data used for STEREO. Orbit results as well as comparisons to independently computed solutions are also included. The successful orbit determination support aided in maneuvering the STEREO spacecraft, launched on October 26, 2006 (00:52 Z), to target the lunar gravity assists required to place the spacecraft into their final heliocentric drift-away orbits where they are providing stereo imaging of the Sun.

49 CFR 38.83 - Mobility aid accessibility.

Code of Federal Regulations, 2013 CFR

2013-10-01

... wheelchair or mobility aid users to reach areas, each with a minimum clear floor space of 48 inches by 30 inches, which do not unduly restrict passenger flow. Space to accommodate wheelchairs and mobility aids may be provided within the normal area used by standees and designation of specific spaces is not...

49 CFR 38.83 - Mobility aid accessibility.

Code of Federal Regulations, 2014 CFR

2014-10-01

... wheelchair or mobility aid users to reach areas, each with a minimum clear floor space of 48 inches by 30 inches, which do not unduly restrict passenger flow. Space to accommodate wheelchairs and mobility aids may be provided within the normal area used by standees and designation of specific spaces is not...

49 CFR 38.83 - Mobility aid accessibility.

Code of Federal Regulations, 2012 CFR

2012-10-01

... wheelchair or mobility aid users to reach areas, each with a minimum clear floor space of 48 inches by 30 inches, which do not unduly restrict passenger flow. Space to accommodate wheelchairs and mobility aids may be provided within the normal area used by standees and designation of specific spaces is not...

Computer Activities for College Algebra and Precalculus.

ERIC Educational Resources Information Center

White, Jacci Wozniak; Norwich, Vicki Howard

Mathematics software can be a great aid in understanding difficult mathematics concepts at all levels. This paper presents nine exercises on calculus concepts by using different software used in mathematics education. Each exercise includes instruction on how to use software in order to highlight a specific concept in mathematics. This paper also…

Software design studies emphasizing Project LOGOS

NASA Technical Reports Server (NTRS)

1972-01-01

The results of a research project on the development of computer software are presented. Research funds of $200,000 were expended over a three year period for software design and projects in connection with Project LOGOS (computer-aided design and certification of computing systems). Abstracts of theses prepared during the project are provided.

29 CFR 541.401 - Computer manufacture and repair.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., the use of computers and computer software programs (e.g., engineers, drafters and others skilled in computer-aided design software), but who are not primarily engaged in computer systems analysis and...

29 CFR 541.401 - Computer manufacture and repair.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., the use of computers and computer software programs (e.g., engineers, drafters and others skilled in computer-aided design software), but who are not primarily engaged in computer systems analysis and...

29 CFR 541.401 - Computer manufacture and repair.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., the use of computers and computer software programs (e.g., engineers, drafters and others skilled in computer-aided design software), but who are not primarily engaged in computer systems analysis and...

29 CFR 541.401 - Computer manufacture and repair.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., the use of computers and computer software programs (e.g., engineers, drafters and others skilled in computer-aided design software), but who are not primarily engaged in computer systems analysis and...

Program Aids Design Of Fluid-Circulating Systems

NASA Technical Reports Server (NTRS)

Bacskay, Allen; Dalee, Robert

1992-01-01

Computer Aided Systems Engineering and Analysis (CASE/A) program is interactive software tool for trade study and analysis, designed to increase productivity during all phases of systems engineering. Graphics-based command-driven software package provides user-friendly computing environment in which engineer analyzes performance and interface characteristics of ECLS/ATC system. Useful during all phases of spacecraft-design program, from initial conceptual design trade studies to actual flight, including pre-flight prediction and in-flight analysis of anomalies. Written in FORTRAN 77.

CAD/CAM complete dentures: a review of two commercial fabrication systems.

PubMed

Kattadiyil, Mathew T; Goodacre, Charles J; Baba, Nadim Z

2013-06-01

The use of computer-aided design and computer-aided manufacturing (CAD/CAM) has become available for complete dentures through the AvaDent and Dentca systems. AvaDent uses laser scanning and computer technology. Teeth are arranged and bases formed using proprietary software.The bases are milled from prepolymerized pucks of resin. Dentca uses computer software to produce virtual maxillary and mandibular edentulous ridges, arrange the teeth and form bases. The dentures are fabricated using a conventional processing technique.

GrammarViz 3.0: Interactive Discovery of Variable-Length Time Series Patterns

DOE PAGES

Senin, Pavel; Lin, Jessica; Wang, Xing; ...

2018-02-23

The problems of recurrent and anomalous pattern discovery in time series, e.g., motifs and discords, respectively, have received a lot of attention from researchers in the past decade. However, since the pattern search space is usually intractable, most existing detection algorithms require that the patterns have discriminative characteristics and have its length known in advance and provided as input, which is an unreasonable requirement for many real-world problems. In addition, patterns of similar structure, but of different lengths may co-exist in a time series. In order to address these issues, we have developed algorithms for variable-length time series pattern discoverymore » that are based on symbolic discretization and grammar inference—two techniques whose combination enables the structured reduction of the search space and discovery of the candidate patterns in linear time. In this work, we present GrammarViz 3.0—a software package that provides implementations of proposed algorithms and graphical user interface for interactive variable-length time series pattern discovery. The current version of the software provides an alternative grammar inference algorithm that improves the time series motif discovery workflow, and introduces an experimental procedure for automated discretization parameter selection that builds upon the minimum cardinality maximum cover principle and aids the time series recurrent and anomalous pattern discovery.« less

GrammarViz 3.0: Interactive Discovery of Variable-Length Time Series Patterns

DOE Office of Scientific and Technical Information (OSTI.GOV)

Senin, Pavel; Lin, Jessica; Wang, Xing

The problems of recurrent and anomalous pattern discovery in time series, e.g., motifs and discords, respectively, have received a lot of attention from researchers in the past decade. However, since the pattern search space is usually intractable, most existing detection algorithms require that the patterns have discriminative characteristics and have its length known in advance and provided as input, which is an unreasonable requirement for many real-world problems. In addition, patterns of similar structure, but of different lengths may co-exist in a time series. In order to address these issues, we have developed algorithms for variable-length time series pattern discoverymore » that are based on symbolic discretization and grammar inference—two techniques whose combination enables the structured reduction of the search space and discovery of the candidate patterns in linear time. In this work, we present GrammarViz 3.0—a software package that provides implementations of proposed algorithms and graphical user interface for interactive variable-length time series pattern discovery. The current version of the software provides an alternative grammar inference algorithm that improves the time series motif discovery workflow, and introduces an experimental procedure for automated discretization parameter selection that builds upon the minimum cardinality maximum cover principle and aids the time series recurrent and anomalous pattern discovery.« less

A "Kane's Dynamics" Model for the Active Rack Isolation System Part Two: Nonlinear Model Development, Verification, and Simplification

NASA Technical Reports Server (NTRS)

Beech, G. S.; Hampton, R. D.; Rupert, J. K.

2004-01-01

Many microgravity space-science experiments require vibratory acceleration levels that are unachievable without active isolation. The Boeing Corporation's active rack isolation system (ARIS) employs a novel combination of magnetic actuation and mechanical linkages to address these isolation requirements on the International Space Station. Effective model-based vibration isolation requires: (1) An isolation device, (2) an adequate dynamic; i.e., mathematical, model of that isolator, and (3) a suitable, corresponding controller. This Technical Memorandum documents the validation of that high-fidelity dynamic model of ARIS. The verification of this dynamics model was achieved by utilizing two commercial off-the-shelf (COTS) software tools: Deneb's ENVISION(registered trademark), and Online Dynamics Autolev(trademark). ENVISION is a robotics software package developed for the automotive industry that employs three-dimensional computer-aided design models to facilitate both forward and inverse kinematics analyses. Autolev is a DOS-based interpreter designed, in general, to solve vector-based mathematical problems and specifically to solve dynamics problems using Kane's method. The simplification of this model was achieved using the small-angle theorem for the joint angle of the ARIS actuators. This simplification has a profound effect on the overall complexity of the closed-form solution while yielding a closed-form solution easily employed using COTS control hardware.

Applying Model-Based Reasoning to the FDIR of the Command and Data Handling Subsystem of the International Space Station

NASA Technical Reports Server (NTRS)

Robinson, Peter; Shirley, Mark; Fletcher, Daryl; Alena, Rick; Duncavage, Dan; Lee, Charles

2003-01-01

All of the International Space Station (ISS) systems which require computer control depend upon the hardware and software of the Command and Data Handling System (C&DH) system, currently a network of over 30 386-class computers called Multiplexor/Dimultiplexors (MDMs)[18]. The Caution and Warning System (C&W)[7], a set of software tasks that runs on the MDMs, is responsible for detecting, classifying, and reporting errors in all ISS subsystems including the C&DH. Fault Detection, Isolation and Recovery (FDIR) of these errors is typically handled with a combination of automatic and human effort. We are developing an Advanced Diagnostic System (ADS) to augment the C&W system with decision support tools to aid in root cause analysis as well as resolve differing human and machine C&DH state estimates. These tools which draw from sources in model-based reasoning[ 16,291, will improve the speed and accuracy of flight controllers by reducing the uncertainty in C&DH state estimation, allowing for a more complete assessment of risk. We have run tests with ISS telemetry and focus on those C&W events which relate to the C&DH system itself. This paper describes our initial results and subsequent plans.

MD Simulations of P-Type ATPases in a Lipid Bilayer System.

PubMed

Autzen, Henriette Elisabeth; Musgaard, Maria

2016-01-01

Molecular dynamics (MD) simulation is a computational method which provides insight on protein dynamics with high resolution in both space and time, in contrast to many experimental techniques. MD simulations can be used as a stand-alone method to study P-type ATPases as well as a complementary method aiding experimental studies. In particular, MD simulations have proved valuable in generating and confirming hypotheses relating to the structure and function of P-type ATPases. In the following, we describe a detailed practical procedure on how to set up and run a MD simulation of a P-type ATPase embedded in a lipid bilayer using software free of use for academics. We emphasize general considerations and problems typically encountered when setting up simulations. While full coverage of all possible procedures is beyond the scope of this chapter, we have chosen to illustrate the MD procedure with the Nanoscale Molecular Dynamics (NAMD) and the Visual Molecular Dynamics (VMD) software suites.

Geometric modeling for computer aided design

NASA Technical Reports Server (NTRS)

Schwing, James L.

1992-01-01

The goal was the design and implementation of software to be used in the conceptual design of aerospace vehicles. Several packages and design studies were completed, including two software tools currently used in the conceptual level design of aerospace vehicles. These tools are the Solid Modeling Aerospace Research Tool (SMART) and the Environment for Software Integration and Execution (EASIE). SMART provides conceptual designers with a rapid prototyping capability and additionally provides initial mass property analysis. EASIE provides a set of interactive utilities that simplify the task of building and executing computer aided design systems consisting of diverse, stand alone analysis codes that result in the streamlining of the exchange of data between programs, reducing errors and improving efficiency.

Custodial Management in the Information Age.

ERIC Educational Resources Information Center

Harris, Jim, Sr.

1999-01-01

Explains how computerizing the custodial department can be achieved through bar coding, hand-held readers, and the appropriate software packages. Software programs that aid cleaning management, track assets, and manage stock are discussed. (GR)

Tier2 Submit Software

EPA Pesticide Factsheets

Download this tool for Windows or Mac, which helps facilities prepare a Tier II electronic chemical inventory report. The data can also be exported into the CAMEOfm (Computer-Aided Management of Emergency Operations) emergency planning software.

A Review of the Suitability of Available Computer Aided Software Engineering (CASE) Tools for the Small Software Development Environment

DTIC Science & Technology

1989-07-11

LITERATURE CITED [Boeh73] Boehm, Barry W., "Software and its Impact: A Quantitative Assessment," Datamation, 19, 5, (May 1973), pp 48-59. [Boeh76...Boehm, Barry W., "Software Engineering," IEEE Transactions on Computers, C-25, 12, (December 1976), pp 1226-1241. [Boeh81a] Boehm, Barry W., Software...Engineering Economics, Prentice-Hall, Inc., Englewood Cliffs, NJ, (1981). [Boeh8lb] Boehm, Barry W., "An Experiment in Small Scale Application Software

Proposal for a New ’Rights in Software’ Clause for Software Acquisitions by the Department of Defense.

DTIC Science & Technology

1986-09-01

point here Is that the capital cost of design and development (including the cost of software tools and/or CAD/CAM programs which aided in the development...and capitalization , software Is in many ways more Ike a hardware component than it is Ike the tech- nical documentation which supports the hardware...Invoked, the owner of intelectual property rights in software may attach appropriate copyright notices to software delivered under this contract. 2.2.2

Software Defined Radio Standard Architecture and its Application to NASA Space Missions

NASA Technical Reports Server (NTRS)

Andro, Monty; Reinhart, Richard C.

2006-01-01

A software defined radio (SDR) architecture used in space-based platforms proposes to standardize certain aspects of radio development such as interface definitions, functional control and execution, and application software and firmware development. NASA has charted a team to develop an open software defined radio hardware and software architecture to support NASA missions and determine the viability of an Agency-wide Standard. A draft concept of the proposed standard has been released and discussed among organizations in the SDR community. Appropriate leveraging of the JTRS SCA, OMG's SWRadio Architecture and other aspects are considered. A standard radio architecture offers potential value by employing common waveform software instantiation, operation, testing and software maintenance. While software defined radios offer greater flexibility, they also poses challenges to the radio development for the space environment in terms of size, mass and power consumption and available technology. An SDR architecture for space must recognize and address the constraints of space flight hardware, and systems along with flight heritage and culture. NASA is actively participating in the development of technology and standards related to software defined radios. As NASA considers a standard radio architecture for space communications, input and coordination from government agencies, the industry, academia, and standards bodies is key to a successful architecture. The unique aspects of space require thorough investigation of relevant terrestrial technologies properly adapted to space. The talk will describe NASA's current effort to investigate SDR applications to space missions and a brief overview of a candidate architecture under consideration for space based platforms.

Computer Aided Instruction (CAI) for the Shipboard Nontactical ADP Program (SNAP). Interim report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Duncan, L.D.; Hammons, C.E.; Hume, R.

Oak Ridge National Laboratory is developing a prototype computer aided instruction package for the Navy Management Systems Support Office. This report discusses the background of the project and the progress to date including a description of the software design, problems encountered, solutions found, and recommendations. The objective of this project is to provide a prototype that will enhance training and can be used as a shipboard refresher and retraining tool. The prototype system will be installed onboard ships where Navy personnel will have ready access to the training. The subsequent testing and evaluation of the prototype could provide the basismore » for a Navy-wide effort to implement computer aided instruction. The work to date has followed a rigorous structured analysis methodology based on the Yourdon/DeMarco techniques. A set of data flow diagrams and a data dictionary are included in the appendices. The problems encountered revolve around requirements to use existing hardware, software, and programmer capabilities for development, implementation, and maintenance of the instructional software. Solutions have been developed which will allow the software to exist in the given environment and still provide advanced features not available in commercial courses.« less

Space-Based Reconfigurable Software Defined Radio Test Bed Aboard International Space Station

NASA Technical Reports Server (NTRS)

Reinhart, Richard C.; Lux, James P.

2014-01-01

The National Aeronautical and Space Administration (NASA) recently launched a new software defined radio research test bed to the International Space Station. The test bed, sponsored by the Space Communications and Navigation (SCaN) Office within NASA is referred to as the SCaN Testbed. The SCaN Testbed is a highly capable communications system, composed of three software defined radios, integrated into a flight system, and mounted to the truss of the International Space Station. Software defined radios offer the future promise of in-flight reconfigurability, autonomy, and eventually cognitive operation. The adoption of software defined radios offers space missions a new way to develop and operate space transceivers for communications and navigation. Reconfigurable or software defined radios with communications and navigation functions implemented in software or VHDL (Very High Speed Hardware Description Language) provide the capability to change the functionality of the radio during development or after launch. The ability to change the operating characteristics of a radio through software once deployed to space offers the flexibility to adapt to new science opportunities, recover from anomalies within the science payload or communication system, and potentially reduce development cost and risk by adapting generic space platforms to meet specific mission requirements. The software defined radios on the SCaN Testbed are each compliant to NASA's Space Telecommunications Radio System (STRS) Architecture. The STRS Architecture is an open, non-proprietary architecture that defines interfaces for the connections between radio components. It provides an operating environment to abstract the communication waveform application from the underlying platform specific hardware such as digital-to-analog converters, analog-to-digital converters, oscillators, RF attenuators, automatic gain control circuits, FPGAs, general-purpose processors, etc. and the interconnections among different radio components.

Manager's handbook for software development, revision 1

NASA Technical Reports Server (NTRS)

1990-01-01

Methods and aids for the management of software development projects are presented. The recommendations are based on analyses and experiences of the Software Engineering Laboratory (SEL) with flight dynamics software development. The management aspects of the following subjects are described: organizing the project, producing a development plan, estimating costs, scheduling, staffing, preparing deliverable documents, using management tools, monitoring the project, conducting reviews, auditing, testing, and certifying.

Airland Battlefield Environment (ALBE) Tactical Decision Aid (TDA) Demonstration Program,

DTIC Science & Technology

1987-11-12

Management System (DBMS) software, GKS graphics libraries, and user interface software. These components of the ATB system software architecture will be... knowlede base ano auqent the decision mak:n• process by providing infocr-mation useful in the formulation and execution of battlefield strategies...Topographic Laboratories as an Engineer. Ms. Capps is managing the software development of the AirLand Battlefield Environment (ALBE) geographic

Implementation of audio computer-assisted interviewing software in HIV/AIDS research.

PubMed

Pluhar, Erika; McDonnell Holstad, Marcia; Yeager, Katherine A; Denzmore-Nwagbara, Pamela; Corkran, Carol; Fielder, Bridget; McCarty, Frances; Diiorio, Colleen

2007-01-01

Computer-assisted interviewing (CAI) has begun to play a more prominent role in HIV/AIDS prevention research. Despite the increased popularity of CAI, particularly audio computer-assisted self-interviewing (ACASI), some research teams are still reluctant to implement ACASI technology because of lack of familiarity with the practical issues related to using these software packages. The purpose of this report is to describe the implementation of one particular ACASI software package, the Questionnaire Development System (QDS; Nova Research Company, Bethesda, MD), in several nursing and HIV/AIDS prevention research settings. The authors present acceptability and satisfaction data from two large-scale public health studies in which they have used QDS with diverse populations. They also address issues related to developing and programming a questionnaire; discuss practical strategies related to planning for and implementing ACASI in the field, including selecting equipment, training staff, and collecting and transferring data; and summarize advantages and disadvantages of computer-assisted research methods.

Free software to analyse the clinical relevance of drug interactions with antiretroviral agents (SIMARV®) in patients with HIV/AIDS.

PubMed

Giraldo, N A; Amariles, P; Monsalve, M; Faus, M J

Highly active antiretroviral therapy has extended the expected lifespan of patients with HIV/AIDS. However, the therapeutic benefits of some drugs used simultaneously with highly active antiretroviral therapy may be adversely affected by drug interactions. The goal was to design and develop a free software to facilitate analysis, assessment, and clinical decision making according to the clinical relevance of drug interactions in patients with HIV/AIDS. A comprehensive Medline/PubMed database search of drug interactions was performed. Articles that recognized any drug interactions in HIV disease were selected. The publications accessed were limited to human studies in English or Spanish, with full texts retrieved. Drug interactions were analyzed, assessed, and grouped into four levels of clinical relevance according to gravity and probability. Software to systematize the information regarding drug interactions and their clinical relevance was designed and developed. Overall, 952 different references were retrieved and 446 selected; in addition, 67 articles were selected from the citation lists of identified articles. A total of 2119 pairs of drug interactions were identified; of this group, 2006 (94.7%) were drug-drug interactions, 1982 (93.5%) had an identified pharmacokinetic mechanism, and 1409 (66.5%) were mediated by enzyme inhibition. In terms of clinical relevance, 1285 (60.6%) drug interactions were clinically significant in patients with HIV (levels 1 and 2). With this information, a software program that facilitates identification and assessment of the clinical relevance of antiretroviral drug interactions (SIMARV ® ) was developed. A free software package with information on 2119 pairs of antiretroviral drug interactions was designed and developed that could facilitate analysis, assessment, and clinical decision making according to the clinical relevance of drug interactions in patients with HIV/AIDS. Copyright © 2016 Elsevier Inc. All rights reserved.

Space Telecommunications Radio Architecture (STRS)

NASA Technical Reports Server (NTRS)

Reinhart, Richard C.

2006-01-01

A software defined radio (SDR) architecture used in space-based platforms proposes to standardize certain aspects of radio development such as interface definitions, functional control and execution, and application software and firmware development. NASA has charted a team to develop an open software defined radio hardware and software architecture to support NASA missions and determine the viability of an Agency-wide Standard. A draft concept of the proposed standard has been released and discussed among organizations in the SDR community. Appropriate leveraging of the JTRS SCA, OMG's SWRadio Architecture and other aspects are considered. A standard radio architecture offers potential value by employing common waveform software instantiation, operation, testing and software maintenance. While software defined radios offer greater flexibility, they also poses challenges to the radio development for the space environment in terms of size, mass and power consumption and available technology. An SDR architecture for space must recognize and address the constraints of space flight hardware, and systems along with flight heritage and culture. NASA is actively participating in the development of technology and standards related to software defined radios. As NASA considers a standard radio architecture for space communications, input and coordination from government agencies, the industry, academia, and standards bodies is key to a successful architecture. The unique aspects of space require thorough investigation of relevant terrestrial technologies properly adapted to space. The talk will describe NASA s current effort to investigate SDR applications to space missions and a brief overview of a candidate architecture under consideration for space based platforms.

Space Telecommunications Radio Architecture (STRS): Technical Overview

NASA Technical Reports Server (NTRS)

Reinhart, Richard C.

2006-01-01

A software defined radio (SDR) architecture used in space-based platforms proposes to standardize certain aspects of radio development such as interface definitions, functional control and execution, and application software and firmware development. NASA has charted a team to develop an open software defined radio hardware and software architecture to support NASA missions and determine the viability of an Agency-wide Standard. A draft concept of the proposed standard has been released and discussed among organizations in the SDR community. Appropriate leveraging of the JTRS SCA, OMG s SWRadio Architecture and other aspects are considered. A standard radio architecture offers potential value by employing common waveform software instantiation, operation, testing and software maintenance. While software defined radios offer greater flexibility, they also poses challenges to the radio development for the space environment in terms of size, mass and power consumption and available technology. An SDR architecture for space must recognize and address the constraints of space flight hardware, and systems along with flight heritage and culture. NASA is actively participating in the development of technology and standards related to software defined radios. As NASA considers a standard radio architecture for space communications, input and coordination from government agencies, the industry, academia, and standards bodies is key to a successful architecture. The unique aspects of space require thorough investigation of relevant terrestrial technologies properly adapted to space. The talk will describe NASA's current effort to investigate SDR applications to space missions and a brief overview of a candidate architecture under consideration for space based platforms.

NASA's SDR Standard: Space Telecommunications Radio System

NASA Technical Reports Server (NTRS)

Reinhart, Richard C.; Johnson, Sandra K.

2007-01-01

A software defined radio (SDR) architecture used in space-based platforms proposes to standardize certain aspects of radio development such as interface definitions, functional control and execution, and application software and firmware development. NASA has charted a team to develop an open software defined radio hardware and software architecture to support NASA missions and determine the viability of an Agency-wide Standard. A draft concept of the proposed standard has been released and discussed among organizations in the SDR community. Appropriate leveraging of the JTRS SCA, OMG s SWRadio Architecture and other aspects are considered. A standard radio architecture offers potential value by employing common waveform software instantiation, operation, testing and software maintenance. While software defined radios offer greater flexibility, they also poses challenges to the radio development for the space environment in terms of size, mass and power consumption and available technology. An SDR architecture for space must recognize and address the constraints of space flight hardware, and systems along with flight heritage and culture. NASA is actively participating in the development of technology and standards related to software defined radios. As NASA considers a standard radio architecture for space communications, input and coordination from government agencies, the industry, academia, and standards bodies is key to a successful architecture. The unique aspects of space require thorough investigation of relevant terrestrial technologies properly adapted to space. The talk will describe NASA s current effort to investigate SDR applications to space missions and a brief overview of a candidate architecture under consideration for space based platforms.

Dynamic CT myocardial perfusion imaging: performance of 3D semi-automated evaluation software.

PubMed

Ebersberger, Ullrich; Marcus, Roy P; Schoepf, U Joseph; Lo, Gladys G; Wang, Yining; Blanke, Philipp; Geyer, Lucas L; Gray, J Cranston; McQuiston, Andrew D; Cho, Young Jun; Scheuering, Michael; Canstein, Christian; Nikolaou, Konstantin; Hoffmann, Ellen; Bamberg, Fabian

2014-01-01

To evaluate the performance of three-dimensional semi-automated evaluation software for the assessment of myocardial blood flow (MBF) and blood volume (MBV) at dynamic myocardial perfusion computed tomography (CT). Volume-based software relying on marginal space learning and probabilistic boosting tree-based contour fitting was applied to CT myocardial perfusion imaging data of 37 subjects. In addition, all image data were analysed manually and both approaches were compared with SPECT findings. Study endpoints included time of analysis and conventional measures of diagnostic accuracy. Of 592 analysable segments, 42 showed perfusion defects on SPECT. Average analysis times for the manual and software-based approaches were 49.1 ± 11.2 and 16.5 ± 3.7 min respectively (P < 0.01). There was strong agreement between the two measures of interest (MBF, ICC = 0.91, and MBV, ICC = 0.88, both P < 0.01) and no significant difference in MBF/MBV with respect to diagnostic accuracy between the two approaches for both MBF and MBV for manual versus software-based approach; respectively; all comparisons P > 0.05. Three-dimensional semi-automated evaluation of dynamic myocardial perfusion CT data provides similar measures and diagnostic accuracy to manual evaluation, albeit with substantially reduced analysis times. This capability may aid the integration of this test into clinical workflows. • Myocardial perfusion CT is attractive for comprehensive coronary heart disease assessment. • Traditional image analysis methods are cumbersome and time-consuming. • Automated 3D perfusion software shortens analysis times. • Automated 3D perfusion software increases standardisation of myocardial perfusion CT. • Automated, standardised analysis fosters myocardial perfusion CT integration into clinical practice.

Software Reviews.

ERIC Educational Resources Information Center

Science and Children, 1989

1989-01-01

Reviews of seven software packages are presented including "The Environment I: Habitats and EcoSystems; II Cycles and Interactions"; "Super Sign Maker"; "The Great Knowledge Race: Substance Abuse"; "Exploring Science: Temperature"; "Fast Food Calculator and RD Aide"; "The Human Body:…

USER'S GUIDE: Strategic Waste Minimization Initiative (SWAMI) Version 2.0 - A Software Tool to Aid in Process Analysis for Pollution Prevention

EPA Science Inventory

The Strategic WAste Minimization Initiative (SWAMI) Software, Version 2.0 is a tool for using process analysis for identifying waste minimization opportunities within an industrial setting. The software requires user-supplied information for process definition, as well as materia...

Managers Handbook for Software Development

NASA Technical Reports Server (NTRS)

Agresti, W.; Mcgarry, F.; Card, D.; Page, J.; Church, V.; Werking, R.

1984-01-01

Methods and aids for the management of software development projects are presented. The recommendations are based on analyses and experiences with flight dynamics software development. The management aspects of organizing the project, producing a development plan, estimation costs, scheduling, staffing, preparing deliverable documents, using management tools, monitoring the project, conducting reviews, auditing, testing, and certifying are described.

Ideas in Practice (3): A Simulated Laboratory Experience in Digital Design.

ERIC Educational Resources Information Center

Cleaver, Thomas G.

1988-01-01

Gives an example of the use of a simplified logic simulator in a logic design course. Discusses some problems in logic design classes, commercially available software, and software problems. Describes computer-aided engineering (CAE) software. Lists 14 experiments in the simulated laboratory and presents students' evaluation of the course. (YP)

IPAD project overview

NASA Technical Reports Server (NTRS)

Fulton, R. E.

1980-01-01

To respond to national needs for improved productivity in engineering design and manufacturing, a NASA supported joint industry/government project is underway denoted Integrated Programs for Aerospace-Vehicle Design (IPAD). The objective is to improve engineering productivity through better use of computer technology. It focuses on development of technology and associated software for integrated company-wide management of engineering information. The project has been underway since 1976 under the guidance of an Industry Technical Advisory Board (ITAB) composed of representatives of major engineering and computer companies and in close collaboration with the Air Force Integrated Computer-Aided Manufacturing (ICAM) program. Results to date on the IPAD project include an in-depth documentation of a representative design process for a large engineering project, the definition and design of computer-aided design software needed to support that process, and the release of prototype software to integrate selected design functions. Ongoing work concentrates on development of prototype software to manage engineering information, and initial software is nearing release.

Strategies for the Creation, Design and Implementation of Effective Interactive Computer-Aided Learning Software in Numerate Business Subjects--The Byzantium Experience.

ERIC Educational Resources Information Center

Wilkinson-Riddle, G. J.; Patel, Ashok

1998-01-01

Discusses courseware development, including intelligent tutoring systems, under the Teaching and Learning Technology Programme and the Byzantium project that was designed to define computer-aided learning performance standards suitable for numerate business subjects; examine reasons to use computer-aided learning; and improve access to educational…

An Operations Management System for the Space Station

NASA Astrophysics Data System (ADS)

Rosenthal, H. G.

1986-09-01

This paper presents an overview of the conceptual design of an integrated onboard Operations Management System (OMS). Both hardware and software concepts are presented and the integrated space station network is discussed. It is shown that using currently available software technology, an integrated software solution for Space Station management and control, implemented with OMS software, is feasible.

[Research and application of computer-aided technology in restoration of maxillary defect].

PubMed

Cheng, Xiaosheng; Liao, Wenhe; Hu, Qingang; Wang, Qian; Dai, Ning

2008-08-01

This paper presents a new method of designing restoration model of maxillectomy defect through Computer aided technology. Firstly, 3D maxillectomy triangle mesh model is constructed from Helical CT data. Secondly, the triangle mesh model is transformed into initial computer-aided design (CAD) model of maxillectomy through reverse engineering software. Thirdly, the 3D virtual restoration model of maxillary defect is obtained after designing and adjusting the initial CAD model through CAD software according to the patient's practical condition. Therefore, the 3D virtual restoration can be fitted very well with the broken part of maxilla. The exported design data can be manufactured using rapid prototyping technology and foundry technology. Finally, the result proved that this method is effective and feasible.

Development of NASA's Space Communications and Navigation Test Bed Aboard ISS to Investigate SDR, On-Board Networking and Navigation Technologies

NASA Technical Reports Server (NTRS)

Reinhart, Richard C.; Kacpura, Thomas J.; Johnson, Sandra K.; Lux, James P.

2010-01-01

NASA is developing an experimental flight payload (referred to as the Space Communication and Navigation (SCAN) Test Bed) to investigate software defined radio (SDR), networking, and navigation technologies, operationally in the space environment. The payload consists of three software defined radios each compliant to NASA s Space Telecommunications Radio System Architecture, a common software interface description standard for software defined radios. The software defined radios are new technology developments underway by NASA and industry partners. Planned for launch in early 2012, the payload will be externally mounted to the International Space Station truss and conduct experiments representative of future mission capability.

Evaluation of Microcomputer-Based Operation and Maintenance Management Systems for Army Water/Wastewater Treatment Plant Operation.

DTIC Science & Technology

1986-07-01

COMPUTER-AIDED OPERATION MANAGEMENT SYSTEM ................. 29 Functions of an Off-Line Computer-Aided Operation Management System Applications of...System Comparisons 85 DISTRIBUTION 5V J. • 0. FIGURES Number Page 1 Hardware Components 21 2 Basic Functions of a Computer-Aided Operation Management System...Plant Visits 26 4 Computer-Aided Operation Management Systems Reviewed for Analysis of Basic Functions 29 5 Progress of Software System Installation and

Engineering specification and system design for CAD/CAM of custom shoes: UMC project effort

NASA Technical Reports Server (NTRS)

Bao, Han P.

1991-01-01

The goal of this project is to supplement the footwear design system of North Carolina State University (NCSU) with a software module to design and manufacture a combination sole. The four areas of concentration were: customization of NASCAD (NASA Computer Aided Design) to the footwear project; use of CENCIT data; computer aided manufacturing activities; and beginning work for the bottom elements of shoes. The task of generating a software module for producing a sole was completed with a demonstrated product realization. The software written in C was delivered to NCSU for inclusion in their design system for custom footwear known as LASTMOD. The machining process of the shoe last was improved using a spiral tool path approach.

Space station: The role of software

NASA Technical Reports Server (NTRS)

Hall, D.

1985-01-01

Software will play a critical role throughout the Space Station Program. This presentation sets the stage and prompts participant interaction at the Software Issues Forum. The presentation is structured into three major topics: (1) an overview of the concept and status of the Space Station Program; (2) several charts designed to lay out the scope and role of software; and (3) information addressing the four specific areas selected for focus at the forum, specifically: software management, the software development environment, languages, and standards. NASA's current thinking is highlighted and some of the relevant critical issues are raised.

Software-Defined Radio for Space-to-Space Communications

NASA Technical Reports Server (NTRS)

Fisher, Ken; Jih, Cindy; Moore, Michael S.; Price, Jeremy C.; Abbott, Ben A.; Fritz, Justin A.

2011-01-01

A paper describes the Space- to-Space Communications System (SSCS) Software- Defined Radio (SDR) research project to determine the most appropriate method for creating flexible and reconfigurable radios to implement wireless communications channels for space vehicles so that fewer radios are required, and commonality in hardware and software architecture can be leveraged for future missions. The ability to reconfigure the SDR through software enables one radio platform to be reconfigured to interoperate with many different waveforms. This means a reduction in the number of physical radio platforms necessary to support a space mission s communication requirements, thus decreasing the total size, weight, and power needed for a mission.

RTEMS SMP and MTAPI for Efficient Multi-Core Space Applications on LEON3/LEON4 Processors

NASA Astrophysics Data System (ADS)

Cederman, Daniel; Hellstrom, Daniel; Sherrill, Joel; Bloom, Gedare; Patte, Mathieu; Zulianello, Marco

2015-09-01

This paper presents the final result of an European Space Agency (ESA) activity aimed at improving the software support for LEON processors used in SMP configurations. One of the benefits of using a multicore system in a SMP configuration is that in many instances it is possible to better utilize the available processing resources by load balancing between cores. This however comes with the cost of having to synchronize operations between cores, leading to increased complexity. While in an AMP system one can use multiple instances of operating systems that are only uni-processor capable, a SMP system requires the operating system to be written to support multicore systems. In this activity we have improved and extended the SMP support of the RTEMS real-time operating system and ensured that it fully supports the multicore capable LEON processors. The targeted hardware in the activity has been the GR712RC, a dual-core core LEON3FT processor, and the functional prototype of ESA's Next Generation Multiprocessor (NGMP), a quad core LEON4 processor. The final version of the NGMP is now available as a product under the name GR740. An implementation of the Multicore Task Management API (MTAPI) has been developed as part of this activity to aid in the parallelization of applications for RTEMS SMP. It allows for simplified development of parallel applications using the task-based programming model. An existing space application, the Gaia Video Processing Unit, has been ported to RTEMS SMP using the MTAPI implementation to demonstrate the feasibility and usefulness of multicore processors for space payload software. The activity is funded by ESA under contract 4000108560/13/NL/JK. Gedare Bloom is supported in part by NSF CNS-0934725.

Assess/Mitigate Risk through the Use of Computer-Aided Software Engineering (CASE) Tools

NASA Technical Reports Server (NTRS)

Aguilar, Michael L.

2013-01-01

The NASA Engineering and Safety Center (NESC) was requested to perform an independent assessment of the mitigation of the Constellation Program (CxP) Risk 4421 through the use of computer-aided software engineering (CASE) tools. With the cancellation of the CxP, the assessment goals were modified to capture lessons learned and best practices in the use of CASE tools. The assessment goal was to prepare the next program for the use of these CASE tools. The outcome of the assessment is contained in this document.

Ground and Space Radar Volume Matching and Comparison Software

NASA Technical Reports Server (NTRS)

Morris, Kenneth; Schwaller, Mathew

2010-01-01

This software enables easy comparison of ground- and space-based radar observations. The software was initially designed to compare ground radar reflectivity from operational, ground based Sand C-band meteorological radars with comparable measurements from the Tropical Rainfall Measuring Mission (TRMM) satellite s Precipitation Radar (PR) instrument. The software is also applicable to other ground-based and space-based radars. The ground and space radar volume matching and comparison software was developed in response to requirements defined by the Ground Validation System (GVS) of Goddard s Global Precipitation Mission (GPM) project. This software innovation is specifically concerned with simplifying the comparison of ground- and spacebased radar measurements for the purpose of GPM algorithm and data product validation. This software is unique in that it provides an operational environment to routinely create comparison products, and uses a direct geometric approach to derive common volumes of space- and ground-based radar data. In this approach, spatially coincident volumes are defined by the intersection of individual space-based Precipitation Radar rays with the each of the conical elevation sweeps of the ground radar. Thus, the resampled volume elements of the space and ground radar reflectivity can be directly compared to one another.

Educational Software for Mapping Quantitative Trait Loci (QTL)

ERIC Educational Resources Information Center

Helms, T. C.; Doetkott, C.

2007-01-01

This educational software was developed to aid teachers and students in their understanding of how the process of identifying the most likely quantitative trait loci (QTL) position is determined between two flanking DNA markers. The objective of the software that we developed was to: (1) show how a QTL is mapped to a position on a chromosome using…

Screen Design Principles of Computer-Aided Instructional Software for Elementary School Students

ERIC Educational Resources Information Center

Berrin, Atiker; Turan, Bülent Onur

2017-01-01

This study aims to present primary school students' views about current educational software interfaces, and to propose principles for educational software screens. The study was carried out with a general screening model. Sample group of the study consisted of sixth grade students in Sehit Ögretmen Hasan Akan Elementary School. In this context,…

Software Tools for Battery Design | Transportation Research | NREL

Science.gov Websites

battery designers, developers, and manufacturers create affordable, high-performance lithium-ion (Li-ion Software Tools for Battery Design Software Tools for Battery Design Under the Computer-Aided ) batteries for next-generation electric-drive vehicles (EDVs). An image of a simulation of a battery pack

Cryogenic Pressure Control Modeling for Ellipsoidal Space Tanks in Reduced Gravity

NASA Technical Reports Server (NTRS)

Hedayat, Ali; Lopez, Alfredo; Grayson, Gary D.; Chandler, Frank O.; Hastings, Leon J.

2008-01-01

A computational fluid dynamics (CFD) model is developed to simulate pressure control of an ellipsoidal-shaped liquid hydrogen tank under external heating in low gravity. Pressure control is provided by an axial jet thermodynamic vent system (TVS) centered within the vessel that injects cooler liquid into the tank, mixing the contents and reducing tank pressure. The two-phase cryogenic tank model considers liquid hydrogen in its own vapor with liquid density varying with temperature only and a fully compressible ullage. The axisymmetric model is developed using a custom version of the commercially available FLOW-3D software and simulates low gravity extrapolations of engineering checkout tests performed at Marshall Space Flight Center in 1999 in support of the Solar Thermal Upper Stage Technology Demonstrator (STUSTD) program. Model results illustrate that stable low gravity liquid-gas interfaces are maintained during all phases of the pressure control cycle. Steady and relatively smooth ullage pressurization rates are predicted. This work advances current low gravity CFD modeling capabilities for cryogenic pressure control and aids the development of a low cost CFD-based design process for space hardware.

Lunar gravity affects leaf movement of Arabidopsis thaliana in the International Space Station.

PubMed

Fisahn, Joachim; Klingelé, Emile; Barlow, Peter

2015-06-01

Cyclic leaf ascent and descent occur in synchrony and phase congruence with the lunisolar tidal force under a broad range of conditions. Digitized records of the vertical leaf movements of Arabidopsis thaliana were collected under space flight conditions in the International Space Station (ISS). Oscillations of leaf movements with periods of 45 and 90 min were found under light-adapted conditions, whereas in darkness, the periods were 45, 90, and 135 min. To demonstrate the close relationship between these oscillations and cyclical variations of the lunisolar gravitational force, we estimated the oscillations of the in-orbit lunisolar tide as they apply to the ISS, with the aid of the Etide software application. In general, in-orbit lunisolar gravitational profiles exhibited a periodicity of 45 min. Alignment of these in-orbit oscillations with the oscillations of Arabidopsis leaf movement revealed high degrees of synchrony and a congruence of phase. These data corroborate previous results which suggested a correlative relationship and a possible causal link between leaf movement rhythms obtained on ground and the rhythmic variation of the lunisolar tidal force.

Community Coordinated Modeling Center: A Powerful Resource in Space Science and Space Weather Education

NASA Astrophysics Data System (ADS)

Chulaki, A.; Kuznetsova, M. M.; Rastaetter, L.; MacNeice, P. J.; Shim, J. S.; Pulkkinen, A. A.; Taktakishvili, A.; Mays, M. L.; Mendoza, A. M. M.; Zheng, Y.; Mullinix, R.; Collado-Vega, Y. M.; Maddox, M. M.; Pembroke, A. D.; Wiegand, C.

2015-12-01

Community Coordinated Modeling Center (CCMC) is a NASA affiliated interagency partnership with the primary goal of aiding the transition of modern space science models into space weather forecasting while supporting space science research. Additionally, over the past ten years it has established itself as a global space science education resource supporting undergraduate and graduate education and research, and spreading space weather awareness worldwide. A unique combination of assets, capabilities and close ties to the scientific and educational communities enable this small group to serve as a hub for raising generations of young space scientists and engineers. CCMC resources are publicly available online, providing unprecedented global access to the largest collection of modern space science models (developed by the international research community). CCMC has revolutionized the way simulations are utilized in classrooms settings, student projects, and scientific labs and serves hundreds of educators, students and researchers every year. Another major CCMC asset is an expert space weather prototyping team primarily serving NASA's interplanetary space weather needs. Capitalizing on its unrivaled capabilities and experiences, the team provides in-depth space weather training to students and professionals worldwide, and offers an amazing opportunity for undergraduates to engage in real-time space weather monitoring, analysis, forecasting and research. In-house development of state-of-the-art space weather tools and applications provides exciting opportunities to students majoring in computer science and computer engineering fields to intern with the software engineers at the CCMC while also learning about the space weather from the NASA scientists.

Agile Development Methods for Space Operations

NASA Technical Reports Server (NTRS)

Trimble, Jay; Webster, Chris

2012-01-01

Main stream industry software development practice has gone from a traditional waterfall process to agile iterative development that allows for fast response to customer inputs and produces higher quality software at lower cost. How can we, the space ops community, adopt state of the art software development practice, achieve greater productivity at lower cost, and maintain safe and effective space flight operations? At NASA Ames, we are developing Mission Control Technologies Software, in collaboration with Johnson Space Center (JSC) and, more recently, the Jet Propulsion Laboratory (JPL).

Systems engineering and integration: Cost estimation and benefits analysis

NASA Technical Reports Server (NTRS)

Dean, ED; Fridge, Ernie; Hamaker, Joe

1990-01-01

Space Transportation Avionics hardware and software cost has traditionally been estimated in Phase A and B using cost techniques which predict cost as a function of various cost predictive variables such as weight, lines of code, functions to be performed, quantities of test hardware, quantities of flight hardware, design and development heritage, complexity, etc. The output of such analyses has been life cycle costs, economic benefits and related data. The major objectives of Cost Estimation and Benefits analysis are twofold: (1) to play a role in the evaluation of potential new space transportation avionics technologies, and (2) to benefit from emerging technological innovations. Both aspects of cost estimation and technology are discussed here. The role of cost analysis in the evaluation of potential technologies should be one of offering additional quantitative and qualitative information to aid decision-making. The cost analyses process needs to be fully integrated into the design process in such a way that cost trades, optimizations and sensitivities are understood. Current hardware cost models tend to primarily use weights, functional specifications, quantities, design heritage and complexity as metrics to predict cost. Software models mostly use functionality, volume of code, heritage and complexity as cost descriptive variables. Basic research needs to be initiated to develop metrics more responsive to the trades which are required for future launch vehicle avionics systems. These would include cost estimating capabilities that are sensitive to technological innovations such as improved materials and fabrication processes, computer aided design and manufacturing, self checkout and many others. In addition to basic cost estimating improvements, the process must be sensitive to the fact that no cost estimate can be quoted without also quoting a confidence associated with the estimate. In order to achieve this, better cost risk evaluation techniques are needed as well as improved usage of risk data by decision-makers. More and better ways to display and communicate cost and cost risk to management are required.

Software Reviews.

ERIC Educational Resources Information Center

Wulfson, Stephen, Ed.

1990-01-01

Reviewed are six software packages for Apple and/or IBM computers. Included are "Autograph,""The New Game Show,""Science Probe-Earth Science,""Pollution Patrol,""Investigating Plant Growth," and "AIDS: The Investigation." Discussed are the grade level, function, availability, cost, and hardware requirements of each. (CW)

Assessing Functional Vision Using Microcomputers.

ERIC Educational Resources Information Center

Spencer, Simon; Ross, Malcolm

1989-01-01

The paper describes a software system which uses microcomputers to aid in the assessment of functional vision in visually impaired students. The software also aims to be visually stimulating and to develop hand-eye coordination, visual memory, and cognitive abilities. (DB)

Iteration and Prototyping in Creating Technical Specifications.

ERIC Educational Resources Information Center

Flynt, John P.

1994-01-01

Claims that the development process for computer software can be greatly aided by the writers of specifications if they employ basic iteration and prototyping techniques. Asserts that computer software configuration management practices provide ready models for iteration and prototyping. (HB)

The University of Michigan's Computer-Aided Engineering Network.

ERIC Educational Resources Information Center

Atkins, D. E.; Olsen, Leslie A.

1986-01-01

Presents an overview of the Computer-Aided Engineering Network (CAEN) of the University of Michigan. Describes its arrangement of workstations, communication networks, and servers. Outlines the factors considered in hardware and software decision making. Reviews the program's impact on students. (ML)

Computer-Aided Engineering Education at the K.U. Leuven.

ERIC Educational Resources Information Center

Snoeys, R.; Gobin, R.

1987-01-01

Describes some recent initiatives and developments in the computer-aided design program in the engineering faculty of the Katholieke Universiteit Leuven (Belgium). Provides a survey of the engineering curriculum, the computer facilities, and the main software packages available. (TW)

Architectural Implementation of NASA Space Telecommunications Radio System Specification

NASA Technical Reports Server (NTRS)

Peters, Kenneth J.; Lux, James P.; Lang, Minh; Duncan, Courtney B.

2012-01-01

This software demonstrates a working implementation of the NASA STRS (Space Telecommunications Radio System) architecture specification. This is a developing specification of software architecture and required interfaces to provide commonality among future NASA and commercial software-defined radios for space, and allow for easier mixing of software and hardware from different vendors. It provides required functions, and supports interaction with STRS-compliant simple test plug-ins ("waveforms"). All of it is programmed in "plain C," except where necessary to interact with C++ plug-ins. It offers a small footprint, suitable for use in JPL radio hardware. Future NASA work is expected to develop into fully capable software-defined radios for use on the space station, other space vehicles, and interplanetary probes.

Computer graphics applications to crew displays

NASA Technical Reports Server (NTRS)

Wyzkoski, J.

1983-01-01

Astronauts are provided much data and information via the monochrome CRT displays on the orbiter. For this project two areas were investigated for the possible introduction of computer graphics to enhance and extend the utility of these displays. One involved reviewing the current orbiter displays and identifying those which could be improved via computer graphics. As an example, the tabular data on electrical power distribution and control was enhanced by the addition of color and bar charts. The other dealt with the development of an aid to berthing a payload with the Remote Manipulator System (RMS). This aid consists of a graphics display of the top, front and side views of the payload and cargo bay and point of resolution (POR) position and attitude data for the current location of the payload. The initial implementation was on an IBM PC clone. The demonstration software installed in the Johnson Space Center Manipulator Development Facility (MD) was reviewed. Due to current hardware limitations, the MDF verision is slow, i.e., about a 40+ seond update rate and, hence, not real-time. Despite this fact, the evaluation of this additional visual cue as an RMS operator aid indicates that this display, with modifications for speed, etc., can assist the crew. Further development is appropriate.

The FoReVer Methodology: A MBSE Framework for Formal Verification

NASA Astrophysics Data System (ADS)

Baracchi, Laura; Mazzini, Silvia; Cimatti, Alessandro; Tonetta, Stefano; Garcia, Gerald

2013-08-01

The need for high level of confidence and operational integrity in critical space (software) systems is well recognized in the Space industry and has been addressed so far through rigorous System and Software Development Processes and stringent Verification and Validation regimes. The Model Based Space System Engineering process (MBSSE) derived in the System and Software Functional Requirement Techniques study (SSFRT) focused on the application of model based engineering technologies to support the space system and software development processes, from mission level requirements to software implementation through model refinements and translations. In this paper we report on our work in the ESA-funded FoReVer project where we aim at developing methodological, theoretical and technological support for a systematic approach to the space avionics system development, in phases 0/A/B/C. FoReVer enriches the MBSSE process with contract-based formal verification of properties, at different stages from system to software, through a step-wise refinement approach, with the support for a Software Reference Architecture.

An ergonomics prototype of adjustable chin stands aid for visual mechanical inspection at electronic manufacturing-based company in Kuantan, Malaysia

NASA Astrophysics Data System (ADS)

Elias, Nurainaa; Mat Yahya, Nafrizuan

2018-04-01

Chin stands aid is a device designed to reduce fatigue on the chin during the Visual Mechanical Inspection (VMI) task for operators in TT Electronic Sdn Bhd, Kuantan, Malaysia. It is also used to reduce cycle time and also improve employee well-being in terms of comfort. In this project, a 3D model of chin stands aid with an ergonomics approach is created using SOLIDWORKS software. Two different concepts were designed and the best one is chosen based on the Pugh concept selection method, concept screening and also concept scoring. After the selection of concepts is done, a prototype of chin stands aid will be developed and a simulation of the prototype is performed. The simulation has been executed by using Workbench ANSYS software as a tool. Stress analysis, deformation analysis, and fatigue analysis have been done to know the strength and lifespan of the product. The prototype also has been tested to know the functionality and also comfortability for the user to use the chin stands aid.

Space Communication and Navigation Testbed Communications Technology for Exploration

NASA Technical Reports Server (NTRS)

Reinhart, Richard

2013-01-01

NASA developed and launched an experimental flight payload (referred to as the Space Communication and Navigation Test Bed) to investigate software defined radio, networking, and navigation technologies, operationally in the space environment. The payload consists of three software defined radios each compliant to NASAs Space Telecommunications Radio System Architecture, a common software interface description standard for software defined radios. The software defined radios are new technology developed by NASA and industry partners. The payload is externally mounted to the International Space Station truss and available to NASA, industry, and university partners to conduct experiments representative of future mission capability. Experiment operations include in-flight reconfiguration of the SDR waveform functions and payload networking software. The flight system communicates with NASAs orbiting satellite relay network, the Tracking, Data Relay Satellite System at both S-band and Ka-band and to any Earth-based compatible S-band ground station.

Open source IPSEC software in manned and unmanned space missions

NASA Astrophysics Data System (ADS)

Edwards, Jacob

Network security is a major topic of research because cyber attackers pose a threat to national security. Securing ground-space communications for NASA missions is important because attackers could endanger mission success and human lives. This thesis describes how an open source IPsec software package was used to create a secure and reliable channel for ground-space communications. A cost efficient, reproducible hardware testbed was also created to simulate ground-space communications. The testbed enables simulation of low-bandwidth and high latency communications links to experiment how the open source IPsec software reacts to these network constraints. Test cases were built that allowed for validation of the testbed and the open source IPsec software. The test cases also simulate using an IPsec connection from mission control ground routers to points of interest in outer space. Tested open source IPsec software did not meet all the requirements. Software changes were suggested to meet requirements.

Saturn S-2 Automatic Software System /SASS/

NASA Technical Reports Server (NTRS)

Parker, P. E.

1967-01-01

SATURN S-2 Automatic Software System /SASS/ was designed and implemented to aid SATURN S-2 program development and to increase the overall operating efficiency within the S-2 data laboratory. This program is written in FORTRAN 2 for SDS 920 computers.

Tips for Good Electronic Presentations.

ERIC Educational Resources Information Center

Strasser, Dennis

1996-01-01

Describes library uses of presentation graphics software and offers tips for creating electronic presentations. Tips include: audience retention; visual aid options; software package options; presentation planning; presentation showing; and use of text, colors, and graphics. Sidebars note common presentation errors and popular presentation…

A study on spatial decision support systems for HIV/AIDS prevention based on COM GIS technology

NASA Astrophysics Data System (ADS)

Yang, Kun; Luo, Huasong; Peng, Shungyun; Xu, Quanli

2007-06-01

Based on the deeply analysis of the current status and the existing problems of GIS technology applications in Epidemiology, this paper has proposed the method and process for establishing the spatial decision support systems of AIDS epidemic prevention by integrating the COM GIS, Spatial Database, GPS, Remote Sensing, and Communication technologies, as well as ASP and ActiveX software development technologies. One of the most important issues for constructing the spatial decision support systems of AIDS epidemic prevention is how to integrate the AIDS spreading models with GIS. The capabilities of GIS applications in the AIDS epidemic prevention have been described here in this paper firstly. Then some mature epidemic spreading models have also been discussed for extracting the computation parameters. Furthermore, a technical schema has been proposed for integrating the AIDS spreading models with GIS and relevant geospatial technologies, in which the GIS and model running platforms share a common spatial database and the computing results can be spatially visualized on Desktop or Web GIS clients. Finally, a complete solution for establishing the decision support systems of AIDS epidemic prevention has been offered in this paper based on the model integrating methods and ESRI COM GIS software packages. The general decision support systems are composed of data acquisition sub-systems, network communication sub-systems, model integrating sub-systems, AIDS epidemic information spatial database sub-systems, AIDS epidemic information querying and statistical analysis sub-systems, AIDS epidemic dynamic surveillance sub-systems, AIDS epidemic information spatial analysis and decision support sub-systems, as well as AIDS epidemic information publishing sub-systems based on Web GIS.

Computer-aided diagnosis software for vulvovaginal candidiasis detection from Pap smear images.

PubMed

Momenzadeh, Mohammadreza; Vard, Alireza; Talebi, Ardeshir; Mehri Dehnavi, Alireza; Rabbani, Hossein

2018-01-01

Vulvovaginal candidiasis (VVC) is a common gynecologic infection and it occurs when there is overgrowth of the yeast called Candida. VVC diagnosis is usually done by observing a Pap smear sample under a microscope and searching for the conidium and mycelium components of Candida. This manual method is time consuming, subjective and tedious. Any diagnosis tools that detect VVC, semi- or full-automatically, can be very helpful to pathologists. This article presents a computer aided diagnosis (CAD) software to improve human diagnosis of VVC from Pap smear samples. The proposed software is designed based on phenotypic and morphology features of the Candida in Pap smear sample images. This software provide a user-friendly interface which consists of a set of image processing tools and analytical results that helps to detect Candida and determine severity of illness. The software was evaluated on 200 Pap smear sample images and obtained specificity of 91.04% and sensitivity of 92.48% to detect VVC. As a result, the use of the proposed software reduces diagnostic time and can be employed as a second objective opinion for pathologists. © 2017 Wiley Periodicals, Inc.

High Performance Computing Software Applications for Space Situational Awareness

NASA Astrophysics Data System (ADS)

Giuliano, C.; Schumacher, P.; Matson, C.; Chun, F.; Duncan, B.; Borelli, K.; Desonia, R.; Gusciora, G.; Roe, K.

The High Performance Computing Software Applications Institute for Space Situational Awareness (HSAI-SSA) has completed its first full year of applications development. The emphasis of our work in this first year was in improving space surveillance sensor models and image enhancement software. These applications are the Space Surveillance Network Analysis Model (SSNAM), the Air Force Space Fence simulation (SimFence), and physically constrained iterative de-convolution (PCID) image enhancement software tool. Specifically, we have demonstrated order of magnitude speed-up in those codes running on the latest Cray XD-1 Linux supercomputer (Hoku) at the Maui High Performance Computing Center. The software applications improvements that HSAI-SSA has made, has had significant impact to the warfighter and has fundamentally changed the role of high performance computing in SSA.

Cost as a technology driver. [in aerospace R and D

NASA Technical Reports Server (NTRS)

Fitzgerald, P. E., Jr.; Savage, M.

1976-01-01

Cost managment as a guiding factor in optimum development of technology, and proper timing of cost-saving programs in the development of a system or technology with payoffs in development and operational advances are discussed and illustrated. Advances enhancing the performance of hardware or software advances raising productivity or reducing cost, are outlined, with examples drawn from: thermochemical thrust maximization, development of cryogenic storage tanks, improvements in fuel cells for Space Shuttle, design of a spacecraft pyrotechnic initiator, cost cutting by reduction in the number of parts to be joined, and cost cutting by dramatic reductions in circuit component number with small-scale double-diffused integrated circuitry. Program-focused supporting research and technology models are devised to aid judicious timing of cost-conscious research programs.

Global positioning system supported pilot's display

NASA Technical Reports Server (NTRS)

Scott, Marshall M., Jr.; Erdogan, Temel; Schwalb, Andrew P.; Curley, Charles H.

1991-01-01

The hardware, software, and operation of the Microwave Scanning Beam Landing System (MSBLS) Flight Inspection System Pilot's Display is discussed. The Pilot's Display is used in conjunction with flight inspection tests that certify the Microwave Scanning Beam Landing System used at Space Shuttle landing facilities throughout the world. The Pilot's Display was developed for the pilot of test aircraft to set up and fly a given test flight path determined by the flight inspection test engineers. This display also aids the aircraft pilot when hazy or cloud cover conditions exist that limit the pilot's visibility of the Shuttle runway during the flight inspection. The aircraft position is calculated using the Global Positioning System and displayed in the cockpit on a graphical display.

Transportable Applications Environment (TAE) Plus - A NASA productivity tool used to develop graphical user interfaces

NASA Technical Reports Server (NTRS)

Szczur, Martha R.

1991-01-01

The Transportable Applications Environment (TAE) Plus, developed at NASA's Goddard Space Flight Center, is an advanced portable user interface development environment which simplifies the process of creating and managing complex application graphical user interfaces (GUIs), supports prototyping, allows applications to be oported easily between different platforms, and encourages appropriate levels of user interface consistency between applications. This paper discusses the capabilities of the TAE Plus tool, and how it makes the job of designing and developing GUIs easier for the application developers. The paper also explains how tools like TAE Plus provide for reusability and ensure reliability of UI software components, as well as how they aid in the reduction of development and maintenance costs.

Computer Aided Teaching of Digital Signal Processing.

ERIC Educational Resources Information Center

Castro, Ian P.

1990-01-01

Describes a microcomputer-based software package developed at the University of Surrey for teaching digital signal processing to undergraduate science and engineering students. Menu-driven software capabilities are explained, including demonstration of qualitative concepts and experimentation with quantitative data, and examples are given of…

29 CFR 541.401 - Computer manufacture and repair.

Code of Federal Regulations, 2011 CFR

2011-07-01

... DEFINING AND DELIMITING THE EXEMPTIONS FOR EXECUTIVE, ADMINISTRATIVE, PROFESSIONAL, COMPUTER AND OUTSIDE..., the use of computers and computer software programs (e.g., engineers, drafters and others skilled in computer-aided design software), but who are not primarily engaged in computer systems analysis and...

Software Engineering Laboratory (SEL) programmer workbench phase 1 evaluation

NASA Technical Reports Server (NTRS)

1981-01-01

Phase 1 of the SEL programmer workbench consists of the design of the following three components: communications link, command language processor, and collection of software aids. A brief description, and evaluation, and recommendations are presented for each of these three components.

An attempt to calculate in silico disintegration time of tablets containing mefenamic acid, a low water-soluble drug.

PubMed

Kimura, Go; Puchkov, Maxim; Leuenberger, Hans

2013-07-01

Based on a Quality by Design (QbD) approach, it is important to follow International Conference on Harmonization (ICH) guidance Q8 (R2) recommendations to explore the design space. The application of an experimental design is, however, not sufficient because of the fact that it is necessary to take into account the effects of percolation theory. For this purpose, an adequate software needs to be applied, capable of detecting percolation thresholds as a function of the distribution of the functional powder particles. Formulation-computer aided design (F-CAD), originally designed to calculate in silico the drug dissolution profiles of a tablet formulation is, for example, a suitable software for this purpose. The study shows that F-CAD can calculate a good estimate of the disintegration time of a tablet formulation consisting of mefenamic acid. More important, F-CAD is capable of replacing expensive laboratory work by performing in silico experiments for the exploration of the formulation design space according to ICH guidance Q8 (R2). As a consequence, a similar workflow existing as best practice in the automotive and aircraft industry can be adopted by the pharmaceutical industry: The drug delivery vehicle can be first fully designed and tested in silico, which will improve the quality of the marketed formulation and save time and money. Copyright © 2013 Wiley Periodicals, Inc.

Open Architecture SDR for Space

NASA Technical Reports Server (NTRS)

Smith, Carl; Long, Chris; Liebetreu, John; Reinhart, Richard C.

2005-01-01

This paper describes an open-architecture SDR (software defined radio) infrastructure that is suitable for space-based operations (Space-SDR). SDR technologies will endow space and planetary exploration systems with dramatically increased capability, reduced power consumption, and significantly less mass than conventional systems, at costs reduced by vigorous competition, hardware commonality, dense integration, reduced obsolescence, interoperability, and software re-use. Significant progress has been recorded on developments like the Joint Tactical Radio System (JSTRS) Software Communication Architecture (SCA), which is oriented toward reconfigurable radios for defense forces operating in multiple theaters of engagement. The JTRS-SCA presents a consistent software interface for waveform development, and facilitates interoperability, waveform portability, software re-use, and technology evolution.

Machine-Aided Indexing at NASA.

ERIC Educational Resources Information Center

Silvester, June P.; And Others

1994-01-01

Describes the National Aeronautics and Space Administration (NASA) Lexical Dictionary (NLD), a machine-aided indexing system used online at the NASA Center for AeroSpace Information (CASI). The functions of NLD system components are described in detail, and production and quality benefits resulting from machine-aided indexing at CASI are…

Audiovisual Aids for Astronomy and Space Physics at an Urban College

ERIC Educational Resources Information Center

Moche, Dinah L.

1973-01-01

Discusses the use of easily available audiovisual aids to teach a one semester course in astronomy and space physics to liberal arts students of both sexes at Queensborough Community College. Included is a list of teaching aids for use in astronomy instruction. (CC)

HOLISTIC APPROACH TO ENVIRONMENTAL MANAGEMENT OF MUNICIPAL SOLID WASTE

EPA Science Inventory

The paper presents results from the application of a new municipal solid waste (MSW) management planning aid to EPA's new facility in the Research Triangle Park, NC. This planning aid, or decision support tool, is computer software that analyzes the cost and environmental impact ...

Supporting Real-Time Operations and Execution through Timeline and Scheduling Aids

NASA Technical Reports Server (NTRS)

Marquez, Jessica J.; Pyrzak, Guy; Hashemi, Sam; Ahmed, Samia; McMillin, Kevin Edward; Medwid, Joseph Daniel; Chen, Diana; Hurtle, Esten

2013-01-01

Since 2003, the NASA Ames Research Center has been actively involved in researching and advancing the state-of-the-art of planning and scheduling tools for NASA mission operations. Our planning toolkit SPIFe (Scheduling and Planning Interface for Exploration) has supported a variety of missions and field tests, scheduling activities for Mars rovers as well as crew on-board International Space Station and NASA earth analogs. The scheduled plan is the integration of all the activities for the day/s. In turn, the agents (rovers, landers, spaceships, crew) execute from this schedule while the mission support team members (e.g., flight controllers) follow the schedule during execution. Over the last couple of years, our team has begun to research and validate methods that will better support users during realtime operations and execution of scheduled activities. Our team utilizes human-computer interaction principles to research user needs, identify workflow processes, prototype software aids, and user test these. This paper discusses three specific prototypes developed and user tested to support real-time operations: Score Mobile, Playbook, and Mobile Assistant for Task Execution (MATE).

The effects of computer-aided design software on engineering students' spatial visualisation skills

NASA Astrophysics Data System (ADS)

Kösa, Temel; Karakuş, Fatih

2018-03-01

The purpose of this study was to determine the influence of computer-aided design (CAD) software-based instruction on the spatial visualisation skills of freshman engineering students in a computer-aided engineering drawing course. A quasi-experimental design was applied, using the Purdue Spatial Visualization Test-Visualization of Rotations (PSVT:R) for both the pre- and the post-test. The participants were 116 freshman students in the first year of their undergraduate programme in the Department of Mechanical Engineering at a university in Turkey. A total of 72 students comprised the experimental group; they were instructed with CAD-based activities in an engineering drawing course. The control group consisted of 44 students who did not attend this course. The results of the study showed that a CAD-based engineering drawing course had a positive effect on developing engineering students' spatial visualisation skills. Additionally, the results of the study showed that spatial visualisation skills can be a predictor for success in a computer-aided engineering drawing course.

Software For Computing Reliability Of Other Software

NASA Technical Reports Server (NTRS)

Nikora, Allen; Antczak, Thomas M.; Lyu, Michael

1995-01-01

Computer Aided Software Reliability Estimation (CASRE) computer program developed for use in measuring reliability of other software. Easier for non-specialists in reliability to use than many other currently available programs developed for same purpose. CASRE incorporates mathematical modeling capabilities of public-domain Statistical Modeling and Estimation of Reliability Functions for Software (SMERFS) computer program and runs in Windows software environment. Provides menu-driven command interface; enabling and disabling of menu options guides user through (1) selection of set of failure data, (2) execution of mathematical model, and (3) analysis of results from model. Written in C language.

Application of NX Siemens PLM software in educational process in preparing students of engineering branch

NASA Astrophysics Data System (ADS)

Sadchikova, G. M.

2017-01-01

This article discusses the results of the introduction of computer-aided design NX by Siemens Plm Software to the classes of a higher education institution. The necessity of application of modern information technologies in teaching students of engineering profile and selection of a software product is substantiated. The author describes stages of the software module study in relation to some specific courses, considers the features of NX software, which require the creation of standard and unified product databases. The article also gives examples of research carried out by the students with the various software modules.

Open Architecture Standard for NASA's Software-Defined Space Telecommunications Radio Systems

NASA Technical Reports Server (NTRS)

Reinhart, Richard C.; Johnson, Sandra K.; Kacpura, Thomas J.; Hall, Charles S.; Smith, Carl R.; Liebetreu, John

2008-01-01

NASA is developing an architecture standard for software-defined radios used in space- and ground-based platforms to enable commonality among radio developments to enhance capability and services while reducing mission and programmatic risk. Transceivers (or transponders) with functionality primarily defined in software (e.g., firmware) have the ability to change their functional behavior through software alone. This radio architecture standard offers value by employing common waveform software interfaces, method of instantiation, operation, and testing among different compliant hardware and software products. These common interfaces within the architecture abstract application software from the underlying hardware to enable technology insertion independently at either the software or hardware layer. This paper presents the initial Space Telecommunications Radio System (STRS) Architecture for NASA missions to provide the desired software abstraction and flexibility while minimizing the resources necessary to support the architecture.

Framework Programmable Platform for the Advanced Software Development Workstation (FPP/ASDW). Demonstration framework document. Volume 1: Concepts and activity descriptions

NASA Technical Reports Server (NTRS)

Mayer, Richard J.; Blinn, Thomas M.; Dewitte, Paul S.; Crump, John W.; Ackley, Keith A.

1992-01-01

The Framework Programmable Software Development Platform (FPP) is a project aimed at effectively combining tool and data integration mechanisms with a model of the software development process to provide an intelligent integrated software development environment. Guided by the model, this system development framework will take advantage of an integrated operating environment to automate effectively the management of the software development process so that costly mistakes during the development phase can be eliminated. The Advanced Software Development Workstation (ASDW) program is conducting research into development of advanced technologies for Computer Aided Software Engineering (CASE).

Configuration management and software measurement in the Ground Systems Development Environment (GSDE)

NASA Technical Reports Server (NTRS)

Church, Victor E.; Long, D.; Hartenstein, Ray; Perez-Davila, Alfredo

1992-01-01

A set of functional requirements for software configuration management (CM) and metrics reporting for Space Station Freedom ground systems software are described. This report is one of a series from a study of the interfaces among the Ground Systems Development Environment (GSDE), the development systems for the Space Station Training Facility (SSTF) and the Space Station Control Center (SSCC), and the target systems for SSCC and SSTF. The focus is on the CM of the software following delivery to NASA and on the software metrics that relate to the quality and maintainability of the delivered software. The CM and metrics requirements address specific problems that occur in large-scale software development. Mechanisms to assist in the continuing improvement of mission operations software development are described.

Cultural objects as objects: materiality, urban space, and the interpretation of AIDS campaigns in Accra, Ghana.

PubMed

McDonnell, Terence E

2010-05-01

AIDS media lead unexpected lives once distributed through urban space: billboards fade, posters go missing, bumper stickers travel to other cities. The materiality of AIDS campaign objects and of the urban settings in which they are displayed structures how the public interprets their messages. Ethnographic observation of AIDS media in situ and interview data reveal how the materiality of objects and places shapes the availability of AIDS knowledge in Accra, Ghana. Significantly for AIDS organizations, these material conditions often systematically obstruct access to AIDS knowledge for particular groups. Attending to materiality rethinks how scholars assess the cultural power of media.

14 CFR 151.95 - Fences; distance markers; navigational and landing aids; and offsite work.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Fences; distance markers; navigational and landing aids; and offsite work. 151.95 Section 151.95 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) AIRPORTS FEDERAL AID TO AIRPORTS Project Programming...

Evolution of a Reconfigurable Processing Platform for a Next Generation Space Software Defined Radio

NASA Technical Reports Server (NTRS)

Kacpura, Thomas J.; Downey, Joseph A.; Anderson, Keffery R.; Baldwin, Keith

2014-01-01

The National Aeronautics and Space Administration (NASA)Harris Ka-Band Software Defined Radio (SDR) is the first, fully reprogrammable space-qualified SDR operating in the Ka-Band frequency range. Providing exceptionally higher data communication rates than previously possible, this SDR offers in-orbit reconfiguration, multi-waveform operation, and fast deployment due to its highly modular hardware and software architecture. Currently in operation on the International Space Station (ISS), this new paradigm of reconfigurable technology is enabling experimenters to investigate navigation and networking in the space environment.The modular SDR and the NASA developed Space Telecommunications Radio System (STRS) architecture standard are the basis for Harris reusable, digital signal processing space platform trademarked as AppSTAR. As a result, two new space radio products are a synthetic aperture radar payload and an Automatic Detection Surveillance Broadcast (ADS-B) receiver. In addition, Harris is currently developing many new products similar to the Ka-Band software defined radio for other applications. For NASAs next generation flight Ka-Band radio development, leveraging these advancements could lead to a more robust and more capable software defined radio.The space environment has special considerations different from terrestrial applications that must be considered for any system operated in space. Each space mission has unique requirements that can make these systems unique. These unique requirements can make products that are expensive and limited in reuse. Space systems put a premium on size, weight and power. A key trade is the amount of reconfigurability in a space system. The more reconfigurable the hardware platform, the easier it is to adapt to the platform to the next mission, and this reduces the amount of non-recurring engineering costs. However, the more reconfigurable platforms often use more spacecraft resources. Software has similar considerations to hardware. Having an architecture standard promotes reuse of software and firmware. Space platforms have limited processor capability, which makes the trade on the amount of amount of flexibility paramount.

Simulation of the human-telerobot interface

NASA Technical Reports Server (NTRS)

Stuart, Mark A.; Smith, Randy L.

1988-01-01

A part of NASA's Space Station will be a Flight Telerobotic Servicer (FTS) used to help assemble, service, and maintain the Space Station. Since the human operator will be required to control the FTS, the design of the human-telerobot interface must be optimized from a human factors perspective. Simulation has been used as an aid in the development of complex systems. Simulation has been especially useful when it has been applied to the development of complex systems. Simulation should ensure that the hardware and software components of the human-telerobot interface have been designed and selected so that the operator's capabilities and limitations have been accommodated for since this is a complex system where few direct comparisons to existent systems can be made. Three broad areas of the human-telerobot interface where simulation can be of assistance are described. The use of simulation not only can result in a well-designed human-telerobot interface, but also can be used to ensure that components have been selected to best meet system's goals, and for operator training.

NASA Tech Briefs, November 2013

NASA Technical Reports Server (NTRS)

2013-01-01

Topics include: Cryogenic Liquid Sample Acquisition System for Remote Space Applications; 5 Spatial Statistical Data Fusion (SSDF); GPS Estimates of Integrated Precipitable Water Aid Weather Forecasters; Integrating a Microwave Radiometer into Radar Hardware for Simultaneous Data Collection Between the Instruments; Rapid Detection of Herpes Viruses for Clinical Applications; High-Speed Data Recorder for Space, Geodesy, and Other High-Speed Recording Applications; Datacasting V3.0; An All-Solid-State, Room-Temperature, Heterodyne Receiver for Atmospheric Spectroscopy at 1.2 THz; Stacked Transformer for Driver Gain and Receive Signal Splitting; Wireless Integrated Microelectronic Vacuum Sensor System; Fabrication Method for LOBSTER-Eye Optics in <110> Silicon; Compact Focal Plane Assembly for Planetary Science; Fabrication Methods for Adaptive Deformable Mirrors; Visiting Vehicle Ground Trajectory Tool; Workflow-Based Software Development Environment; Mobile Thread Task Manager; A Kinematic Calibration Process for Flight Robotic Arms; Magnetostrictive Alternator; Bulk Metallic Glasses and Composites for Optical and Compliant Mechanisms; Detection of Only Viable Bacterial Spores Using a Live/Dead Indicator in Mixed Populations; and Intravenous Fluid Generation System.

3D printing the pterygopalatine fossa: a negative space model of a complex structure.

PubMed

Bannon, Ross; Parihar, Shivani; Skarparis, Yiannis; Varsou, Ourania; Cezayirli, Enis

2018-02-01

The pterygopalatine fossa is one of the most complex anatomical regions to understand. It is poorly visualized in cadaveric dissection and most textbooks rely on schematic depictions. We describe our approach to creating a low-cost, 3D model of the pterygopalatine fossa, including its associated canals and foramina, using an affordable "desktop" 3D printer. We used open source software to create a volume render of the pterygopalatine fossa from axial slices of a head computerised tomography scan. These data were then exported to a 3D printer to produce an anatomically accurate model. The resulting 'negative space' model of the pterygopalatine fossa provides a useful and innovative aid for understanding the complex anatomical relationships of the pterygopalatine fossa. This model was designed primarily for medical students; however, it will also be of interest to postgraduates in ENT, ophthalmology, neurosurgery, and radiology. The technical process described may be replicated by other departments wishing to develop their own anatomical models whilst incurring minimal costs.

Modeling and Analysis of Space Based Transceivers

NASA Technical Reports Server (NTRS)

Moore, Michael S.; Price, Jeremy C.; Reinhart, Richard; Liebetreu, John; Kacpura, Tom J.

2005-01-01

This paper presents the tool chain, methodology, and results of an on-going study being performed jointly by Space Communication Experts at NASA Glenn Research Center (GRC), General Dynamics C4 Systems (GD), and Southwest Research Institute (SwRI). The team is evaluating the applicability and tradeoffs concerning the use of Software Defined Radio (SDR) technologies for Space missions. The Space Telecommunications Radio Systems (STRS) project is developing an approach toward building SDR-based transceivers for space communications applications based on an accompanying software architecture that can be used to implement transceivers for NASA space missions. The study is assessing the overall cost and benefit of employing SDR technologies in general, and of developing a software architecture standard for its space SDR transceivers. The study is considering the cost and benefit of existing architectures, such as the Joint Tactical Radio Systems (JTRS) Software Communications Architecture (SCA), as well as potential new space-specific architectures.

Software reconfigurable processor technologies: the key to long-life infrastructure for future space missions

NASA Technical Reports Server (NTRS)

Srinivasan, J.; Farrington, A.; Gray, A.

2001-01-01

They present an overview of long-life reconfigurable processor technologies and of a specific architecture for implementing a software reconfigurable (software-defined) network processor for space applications.

The TI-99/4A Software.

ERIC Educational Resources Information Center

Wrege, Rachael; And Others

1982-01-01

Describes the software modules produced by Texas Instruments for use with the TI-99/4A home computer. Among the modules described are: Personal Real Estate, Programing Aids, Home Financial Decisions, Music Maker, Weight Control and Nutrition, Early Learning Fun, and Tax/Investment Record Keeping. (JL)

Programming Language CAMIL II: Implementation and Evaluation.

ERIC Educational Resources Information Center

Gardner, Edward

A reimplementation of Computer assisted/managed instruction language (CAMIL) for qualitative and quantitative improvements in the software is presented. The reformatted language is described narratively, and major components of the system software are indicated and discussed. Authoring aids and imbedded support facilities are also described, and…

Heterogeneous Software System Interoperability Through Computer-Aided Resolution of Modeling Differences

DTIC Science & Technology

2002-06-01

techniques for addressing the software component retrieval problem. Steigerwald [Ste91] introduced the use of algebraic specifications for defining the...provided in terms of a specification written using Luqi’s Prototype Specification Description Language (PSDL) [LBY88] augmented with an algebraic

Integrating a flexible modeling framework (FMF) with the network security assessment instrument to reduce software security risk

NASA Technical Reports Server (NTRS)

Gilliam, D. P.; Powell, J. D.

2002-01-01

This paper presents a portion of an overall research project on the generation of the network security assessment instrument to aid developers in assessing and assuring the security of software in the development and maintenance lifecycles.

Space Station Mission Planning System (MPS) development study. Volume 1: Executive summary

NASA Technical Reports Server (NTRS)

Klus, W. J.

1987-01-01

The basic objective of the Space Station (SS) Mission Planning System (MPS) Development Study was to define a baseline Space Station mission plan and the associated hardware and software requirements for the system. A detailed definition of the Spacelab (SL) payload mission planning process and SL Mission Integration Planning System (MIPS) software was derived. A baseline concept was developed for performing SS manned base payload mission planning, and it was consistent with current Space Station design/operations concepts and philosophies. The SS MPS software requirements were defined. Also, requirements for new software include candidate programs for the application of artificial intelligence techniques to capture and make more effective use of mission planning expertise. A SS MPS Software Development Plan was developed which phases efforts for the development software to implement the SS mission planning concept.

Automating software design system DESTA

NASA Technical Reports Server (NTRS)

Lovitsky, Vladimir A.; Pearce, Patricia D.

1992-01-01

'DESTA' is the acronym for the Dialogue Evolutionary Synthesizer of Turnkey Algorithms by means of a natural language (Russian or English) functional specification of algorithms or software being developed. DESTA represents the computer-aided and/or automatic artificial intelligence 'forgiving' system which provides users with software tools support for algorithm and/or structured program development. The DESTA system is intended to provide support for the higher levels and earlier stages of engineering design of software in contrast to conventional Computer Aided Design (CAD) systems which provide low level tools for use at a stage when the major planning and structuring decisions have already been taken. DESTA is a knowledge-intensive system. The main features of the knowledge are procedures, functions, modules, operating system commands, batch files, their natural language specifications, and their interlinks. The specific domain for the DESTA system is a high level programming language like Turbo Pascal 6.0. The DESTA system is operational and runs on an IBM PC computer.

Data and Analysis Center for Software: An IAC in Transition.

DTIC Science & Technology

1983-06-01

reviewed and is approved for publication. * APPROVEDt Proj ect Engineer . JOHN J. MARCINIAK, Colonel, USAF Chief, Command and Control Division . FOR THE CO...SUPPLEMENTARY NOTES RADC Project Engineer : John Palaimo (COEE) It. KEY WORDS (Conilnuo n rever*e aide if necessary and identify by block numober...Software Engineering Software Technology Information Analysis Center Database Scientific and Technical Information 20. ABSTRACT (Continue on reverse side It

Finding Diamonds in the Rough

NASA Technical Reports Server (NTRS)

2000-01-01

HighTower Software, Inc. has developed a commercial software application originally designed at JPL that helps users identify deviations from norms out of massive quantities of data. The commercial product is known as CyberGrid and the same software is still supporting NASA's Voyager, Galileo and Cassini missions. CyberGrid generates 3-D graphs of data and has been used in AIDS research as well as e-commerce applications.

Space shuttle orbiter avionics software: Post review report for the entry FACI (First Article Configuration Inspection). [including orbital flight tests integrated system

NASA Technical Reports Server (NTRS)

Markos, H.

1978-01-01

Status of the computer programs dealing with space shuttle orbiter avionics is reported. Specific topics covered include: delivery status; SSW software; SM software; DL software; GNC software; level 3/4 testing; level 5 testing; performance analysis, SDL readiness for entry first article configuration inspection; and verification assessment.

DEVELOPMENT AND USE OF COMPUTER-AIDED PROCESS ENGINEERING TOOLS FOR POLLUTION PREVENTION

EPA Science Inventory

The use of Computer-Aided Process Engineering (CAPE) and process simulation tools has become established industry practice to predict simulation software, new opportunities are available for the creation of a wide range of ancillary tools that can be used from within multiple sim...

Space Communication and Navigation SDR Testbed, Overview and Opportunity for Experiments

NASA Technical Reports Server (NTRS)

Reinhart, Richard C.

2013-01-01

NASA has developed an experimental flight payload (referred to as the Space Communication and Navigation (SCAN) Test Bed) to investigate software defined radio (SDR) communications, networking, and navigation technologies, operationally in the space environment. The payload consists of three software defined radios each compliant to NASAs Space Telecommunications Radio System Architecture, a common software interface description standard for software defined radios. The software defined radios are new technology developments underway by NASA and industry partners launched in 2012. The payload is externally mounted to the International Space Station truss to conduct experiments representative of future mission capability. Experiment operations include in-flight reconfiguration of the SDR waveform functions and payload networking software. The flight system will communicate with NASAs orbiting satellite relay network, the Tracking and Data Relay Satellite System at both S-band and Ka-band and to any Earth-based compatible S-band ground station. The system is available for experiments by industry, academia, and other government agencies to participate in the SDR technology assessments and standards advancements.

Software Component Technologies and Space Applications

NASA Technical Reports Server (NTRS)

Batory, Don

1995-01-01

In the near future, software systems will be more reconfigurable than hardware. This will be possible through the advent of software component technologies which have been prototyped in universities and research labs. In this paper, we outline the foundations for those technologies and suggest how they might impact software for space applications.

Creating social spaces to tackle AIDS-related stigma: reviewing the role of church groups in Sub-Saharan Africa.

PubMed

Campbell, C; Skovdal, M; Gibbs, A

2011-08-01

An expanding body of literature explores the role of African church groups in facilitating or hindering the support of people living with AIDS and challenging or contributing to HIV/AIDS-related stigma. Treating church groups as social spaces in which HIV/AIDS-related stigma may potentially be challenged, we systematically review this literature, identifying five themes that highlight the complex and contradictory role of the church as a potential agent of health-enhancing social change. In many ways the church perpetuates HIV/AIDS-related stigma through (i) moralistic attitudes and (ii) its reinforcement of conservative gender ideologies. However some churches have managed move towards action that makes a more positive contribution to HIV/AIDS management through (iii) promoting various forms of social control for HIV prevention, (iv) contributing to the care and support of the AIDS-affected and (v) providing social spaces for challenging stigmatising ideas and practices. We conclude that church groups, including church leadership, can play a key role in facilitating or hindering the creation of supportive social spaces to challenge stigma. Much work remains to be done in developing deeper understandings of the multi-layered factors that enable some churches, but not others, to respond effectively to HIV/AIDS.

Creating Social Spaces to Tackle AIDS-Related Stigma: Reviewing the Role of Church Groups in Sub-Saharan Africa

PubMed Central

Skovdal, M.; Gibbs, A.

2012-01-01

An expanding body of literature explores the role of African church groups in facilitating or hindering the support of people living with AIDS and challenging or contributing to HIV/AIDS-related stigma. Treating church groups as social spaces in which HIV/AIDS-related stigma may potentially be challenged, we systematically review this literature, identifying five themes that highlight the complex and contradictory role of the church as a potential agent of health-enhancing social change. In many ways the church perpetuates HIV/AIDS-related stigma through (i) moralistic attitudes and (ii) its reinforcement of conservative gender ideologies. However some churches have managed move towards action that makes a more positive contribution to HIV/AIDS management through (iii) promoting various forms of social control for HIV prevention, (iv) contributing to the care and support of the AIDS-affected and (v) providing social spaces for challenging stigmatising ideas and practices. We conclude that church groups, including church leadership, can play a key role in facilitating or hindering the creation of supportive social spaces to challenge stigma. Much work remains to be done in developing deeper understandings of the multi-layered factors that enable some churches, but not others, to respond effectively to HIV/AIDS. PMID:20668927

A search for stellar occultations by Uranus, Neptune, Pluto, and their satellites: 1990-1999

NASA Technical Reports Server (NTRS)

Mink, Douglas J.

1991-01-01

A search for occultations of stars by Uranus, Neptune, and Pluto between 1990 and 1999 was carried out by combining ephemeris information and star positions using very accurate occultation modeling software. Stars from both the Space Telescope Guide Catalog and photographic plates taken by Arnold Klemola at Lick Observatory were compared with planet positions from the JPL DE-130 ephemeris, with local modifications for Pluto and Charon. Some 666 possible occultations by the Uranian ring, 143 possible occultations by Neptune, and 40 possible occultations by Pluto and/or Charon were found among stars with visual magnitudes as faint as 16. Before the star positions could be obtained, the occultation prediction software was used to aid many observers in observing the occultation of 28 Sagitarii by Saturn in July 1989. As a test on other outer solar system objects, 17 possible occultations were found in a search of the Guide Star Catalog for occultations by 2060 Chiron, and interesting object between Saturn and Uranus which shows both cometary and asteroidal properties.

A search for stellar occultations by Uranus, Neptune, Pluto, and their satellites: 1990-1999

NASA Astrophysics Data System (ADS)

Mink, Douglas J.

1991-03-01

A search for occultations of stars by Uranus, Neptune, and Pluto between 1990 and 1999 was carried out by combining ephemeris information and star positions using very accurate occultation modeling software. Stars from both the Space Telescope Guide Catalog and photographic plates taken by Arnold Klemola at Lick Observatory were compared with planet positions from the JPL DE-130 ephemeris, with local modifications for Pluto and Charon. Some 666 possible occultations by the Uranian ring, 143 possible occultations by Neptune, and 40 possible occultations by Pluto and/or Charon were found among stars with visual magnitudes as faint as 16. Before the star positions could be obtained, the occultation prediction software was used to aid many observers in observing the occultation of 28 Sagitarii by Saturn in July 1989. As a test on other outer solar system objects, 17 possible occultations were found in a search of the Guide Star Catalog for occultations by 2060 Chiron, and interesting object between Saturn and Uranus which shows both cometary and asteroidal properties.

Incorporating Software Requirements into the System RFP: Survey of RFP Language for Software by Topic, v. 2.0

DTIC Science & Technology

2009-05-01

CDRL) System - Terminal S TMOS - SEIT CL TMOS - IA/ Crypto CL Space - Payload S Space - SEIT C Space - IA/ Crypto C Role Legend: CL...strategy for maintaining the currency of the technology (through Commercial off-the-shelf software (COTS) and other reusable Non-Developmental Items (NDI...the strategy for maintaining the currency of technology (e.g., through Commercial off-the-shelf software (COTS) insertion, technology refresh

Models and metrics for software management and engineering

NASA Technical Reports Server (NTRS)

Basili, V. R.

1988-01-01

This paper attempts to characterize and present a state of the art view of several quantitative models and metrics of the software life cycle. These models and metrics can be used to aid in managing and engineering software projects. They deal with various aspects of the software process and product, including resources allocation and estimation, changes and errors, size, complexity and reliability. Some indication is given of the extent to which the various models have been used and the success they have achieved.

Firing Room Remote Application Software Development

NASA Technical Reports Server (NTRS)

Liu, Kan

2015-01-01

The Engineering and Technology Directorate (NE) at National Aeronautics and Space Administration (NASA) Kennedy Space Center (KSC) is designing a new command and control system for the checkout and launch of Space Launch System (SLS) and future rockets. The purposes of the semester long internship as a remote application software developer include the design, development, integration, and verification of the software and hardware in the firing rooms, in particular with the Mobile Launcher (ML) Launch Accessories (LACC) subsystem. In addition, a software test verification procedure document was created to verify and checkout LACC software for Launch Equipment Test Facility (LETF) testing.

Software Infrastructure for Computer-aided Drug Discovery and Development, a Practical Example with Guidelines.

PubMed

Moretti, Loris; Sartori, Luca

2016-09-01

In the field of Computer-Aided Drug Discovery and Development (CADDD) the proper software infrastructure is essential for everyday investigations. The creation of such an environment should be carefully planned and implemented with certain features in order to be productive and efficient. Here we describe a solution to integrate standard computational services into a functional unit that empowers modelling applications for drug discovery. This system allows users with various level of expertise to run in silico experiments automatically and without the burden of file formatting for different software, managing the actual computation, keeping track of the activities and graphical rendering of the structural outcomes. To showcase the potential of this approach, performances of five different docking programs on an Hiv-1 protease test set are presented. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Geometric modeling for computer aided design

NASA Technical Reports Server (NTRS)

Schwing, James L.

1993-01-01

Over the past several years, it has been the primary goal of this grant to design and implement software to be used in the conceptual design of aerospace vehicles. The work carried out under this grant was performed jointly with members of the Vehicle Analysis Branch (VAB) of NASA LaRC, Computer Sciences Corp., and Vigyan Corp. This has resulted in the development of several packages and design studies. Primary among these are the interactive geometric modeling tool, the Solid Modeling Aerospace Research Tool (smart), and the integration and execution tools provided by the Environment for Application Software Integration and Execution (EASIE). In addition, it is the purpose of the personnel of this grant to provide consultation in the areas of structural design, algorithm development, and software development and implementation, particularly in the areas of computer aided design, geometric surface representation, and parallel algorithms.

Computerizing Your Program.

ERIC Educational Resources Information Center

Curtis, Rick

This paper summarizes information about using computer hardware and software to aid in making purchase decisions that are based on user needs. The two major options in hardware are IBM-compatible machines and the Apple Macintosh line. The three basic software applications include word processing, database management, and spreadsheet applications.…

Using Computer Technology To Aid the Disabled Reader.

ERIC Educational Resources Information Center

Balajthy, Ernest

When matched for achievement level and educational objectives, computer technology can be particularly effective with at-risk students. Computer-assisted instructional software is the most widely available type of software. An exciting development pertinent to literacy education is the development of the "electronic book" (also called…

Microcomputers in the Curriculum: Micros and the First R.

ERIC Educational Resources Information Center

Balajthy, Ernest; Reinking, David

1985-01-01

Introduces the range of computer software currently available to aid in developing children's basic skills in reading, including programs for reading readiness, word recognition, vocabulary development, reading comprehension, and learning motivation. Additional information on software and computer use is provided in sidebars by Gwen Solomon and…

Computer Needs of Severely Mentally Retarded Persons.

ERIC Educational Resources Information Center

Flanagan, Kelly

1982-01-01

The article reviews technology applicable for use by severely mentally retarded learners. Descriptions are given of assistive devices (including communication aids), controls and interfaces (such as single switch access to standard software), and software (including games to teach cause and effect and simple matching and counting). (CL)

SCA Waveform Development for Space Telemetry

NASA Technical Reports Server (NTRS)

Mortensen, Dale J.; Kifle, Multi; Hall, C. Steve; Quinn, Todd M.

2004-01-01

The NASA Glenn Research Center is investigating and developing suitable reconfigurable radio architectures for future NASA missions. This effort is examining software-based open-architectures for space based transceivers, as well as common hardware platform architectures. The Joint Tactical Radio System's (JTRS) Software Communications Architecture (SCA) is a candidate for the software approach, but may need modifications or adaptations for use in space. An in-house SCA compliant waveform development focuses on increasing understanding of software defined radio architectures and more specifically the JTRS SCA. Space requirements put a premium on size, mass, and power. This waveform development effort is key to evaluating tradeoffs with the SCA for space applications. Existing NASA telemetry links, as well as Space Exploration Initiative scenarios, are the basis for defining the waveform requirements. Modeling and simulations are being developed to determine signal processing requirements associated with a waveform and a mission-specific computational burden. Implementation of the waveform on a laboratory software defined radio platform is proceeding in an iterative fashion. Parallel top-down and bottom-up design approaches are employed.

Computer Aided Drafting. Instructor's Guide.

ERIC Educational Resources Information Center

Henry, Michael A.

This guide is intended for use in introducing students to the operation and applications of computer-aided drafting (CAD) systems. The following topics are covered in the individual lessons: understanding CAD (CAD versus traditional manual drafting and care of software and hardware); using the components of a CAD system (primary and other input…

Application Processing, 2003-2004. EDExpress Training. Participant Guide.

ERIC Educational Resources Information Center

Office of Student Financial Assistance (ED), Washington, DC.

This participant guide contains training materials for processing applications for student financial aid under the EDExpress system. Representatives of institutions of higher education receive training in the use of EDExpress software that allows the school to manage student financial aid records. The guide contains these sessions: (1) welcome and…

Schools (Students) Exchanging CAD/CAM Files over the Internet.

ERIC Educational Resources Information Center

Mahoney, Gary S.; Smallwood, James E.

This document discusses how students and schools can benefit from exchanging computer-aided design/computer-aided manufacturing (CAD/CAM) files over the Internet, explains how files are exchanged, and examines the problem of selected hardware/software incompatibility. Key terms associated with information search services are defined, and several…

Software Engineering Techniques for Computer-Aided Learning.

ERIC Educational Resources Information Center

Ibrahim, Bertrand

1989-01-01

Describes the process for developing tutorials for computer-aided learning (CAL) using a programing language rather than an authoring system. The workstation used is described, the use of graphics is discussed, the role of a local area network (LAN) is explained, and future plans are discussed. (five references) (LRW)

Computer-aided evaluation of low-dose and low-contrast agent third-generation dual-source CT angiography prior to transcatheter aortic valve implantation (TAVI).

PubMed

Dankerl, Peter; Hammon, Matthias; Seuss, Hannes; Tröbs, Monique; Schuhbaeck, Annika; Hell, Michaela M; Cavallaro, Alexander; Achenbach, Stephan; Uder, Michael; Marwan, Mohamed

2017-05-01

To evaluate the performance of computer-aided evaluation software for a comprehensive workup of patients prior to transcatheter aortic valve implantation (TAVI) using low-contrast agent and low radiation dose third-generation dual-source CT angiography. We evaluated 30 consecutive patients scheduled for TAVI. All patients underwent ECG-triggered high-pitch dual-source CT angiography of the aortic root and aorta with a standardized contrast agent volume (30 ml Imeron350, flow rate 4 ml/s) and low-dose (100 kv/350 mAs) protocol. An expert (10 years of experience) manually evaluated aortic root and iliac access dimensions (distance between coronary ostia and aortic annulus, minimal/maximal diameters and area-derived diameter of the aortic annulus) and best CT-predicted fluoroscopic projection angle as the reference standard. Utilizing computer-aided software (syngo.via), the same pre-TAVI workup was performed and compared to the reference standard. Mean CTDI[Formula: see text] was 3.46 mGy and mean DLP 217.6 ± 12.1 mGy cm, corresponding to a mean effective dose of 3.7 ± 0.2 mSv. Computer-aided evaluation was successful in all but one patient. Compared to the reference standard, Bland-Altman analysis indicated very good agreement for the distances between aortic annulus and coronary ostia (RCA: mean difference 0.8 mm; 95 % CI 0.4-1.2 mm; LM: mean difference 0.9 mm; 95 % CI 0.5-1.3 mm); however, we demonstrated a systematic overestimation of annulus- derived diameter using the software (mean difference 44.4 mm[Formula: see text]; 95 % CI 30.4-58.3 mm[Formula: see text]). Based on respective annulus dimensions, the recommended prosthesis size (Edwards SAPIEN 3) matched in 26 out of the 29 patients (90 %). CT-derived fluoroscopic projection angles showed an excellent agreement for both methods. Out of 58 iliac arteries, 15 (25 %) arteries could not be segmented by the software. Preprocessing time of the software was 71 ± 11 s (range 51-96 s), and reading time with the software was 118 ± 31 s (range 68-201 s). In the workup of pre-TAVI CT angiography, computer-aided evaluation of low-contrast, low-dose examinations is feasible with good agreement and quick reading time. However, a systematic overestimation of the aortic annulus area is observed.

ACES: Space shuttle flight software analysis expert system

NASA Technical Reports Server (NTRS)

Satterwhite, R. Scott

1990-01-01

The Analysis Criteria Evaluation System (ACES) is a knowledge based expert system that automates the final certification of the Space Shuttle onboard flight software. Guidance, navigation and control of the Space Shuttle through all its flight phases are accomplished by a complex onboard flight software system. This software is reconfigured for each flight to allow thousands of mission-specific parameters to be introduced and must therefore be thoroughly certified prior to each flight. This certification is performed in ground simulations by executing the software in the flight computers. Flight trajectories from liftoff to landing, including abort scenarios, are simulated and the results are stored for analysis. The current methodology of performing this analysis is repetitive and requires many man-hours. The ultimate goals of ACES are to capture the knowledge of the current experts and improve the quality and reduce the manpower required to certify the Space Shuttle onboard flight software.

The Design and Development of a Web-Interface for the Software Engineering Automation System

DTIC Science & Technology

2001-09-01

application on the Internet. 14. SUBJECT TERMS Computer Aided Prototyping, Real Time Systems , Java 15. NUMBER OF...difficult. Developing the entire system only to find it does not meet the customer’s needs is a tremendous waste of time. Real - time systems need a...software prototyping is an iterative software development methodology utilized to improve the analysis and design of real - time systems [2]. One

A User's Guide to the Meta-Analysis of Research Studies. Meta-Stat: Software To Aid in the Meta-Analysis of Research Findings.

ERIC Educational Resources Information Center

Rudner, Lawrence M.; Glass Gene V.; Evartt, David L.; Emery, Patrick J.

This manual and the accompanying software are intended to provide a step-by-step guide to conducting a meta-analytic study along with references for further reading and free high-quality software, "Meta-Stat.""Meta-Stat" is a comprehensive package designed to help in the meta-analysis of research studies in the social and behavioral sciences.…

Software Aids for radiologists: Part 1, Useful Photoshop skills.

PubMed

Gross, Joel A; Thapa, Mahesh M

2012-12-01

The purpose of this review is to describe the use of several essential techniques and tools in Adobe Photoshop image-editing software. The techniques shown expand on those previously described in the radiologic literature. Radiologists, especially those with minimal experience with image-editing software, can quickly apply a few essential Photoshop tools to minimize the frustration that can result from attempting to navigate a complex user interface.

Development of a Communications Front End Processor (FEP) for the VAX-11/780 Using an LSI-11/23.

DTIC Science & Technology

1983-12-01

9 Approach . . . . . . . . . . . . . . . . . . 11 Software Development Life Cycle . . . . . . . 11 Requirements Analysis...proven to be useful (25] during the Software Development Life Cycle of a project. Development tools and documentation aids used throughout this effort...include "Structure Charts" ( ref Appendix B ), a "Data Dictionary" ( ref Appendix C ),and Program Design Language CPDL). 1.5.1 Software Development- Life

Computer-Aided System Engineering and Analysis (CASE/A) Programmer's Manual, Version 5.0

NASA Technical Reports Server (NTRS)

Knox, J. C.

1996-01-01

The Computer Aided System Engineering and Analysis (CASE/A) Version 5.0 Programmer's Manual provides the programmer and user with information regarding the internal structure of the CASE/A 5.0 software system. CASE/A 5.0 is a trade study tool that provides modeling/simulation capabilities for analyzing environmental control and life support systems and active thermal control systems. CASE/A has been successfully used in studies such as the evaluation of carbon dioxide removal in the space station. CASE/A modeling provides a graphical and command-driven interface for the user. This interface allows the user to construct a model by placing equipment components in a graphical layout of the system hardware, then connect the components via flow streams and define their operating parameters. Once the equipment is placed, the simulation time and other control parameters can be set to run the simulation based on the model constructed. After completion of the simulation, graphical plots or text files can be obtained for evaluation of the simulation results over time. Additionally, users have the capability to control the simulation and extract information at various times in the simulation (e.g., control equipment operating parameters over the simulation time or extract plot data) by using "User Operations (OPS) Code." This OPS code is written in FORTRAN with a canned set of utility subroutines for performing common tasks. CASE/A version 5.0 software runs under the VAX VMS(Trademark) environment. It utilizes the Tektronics 4014(Trademark) graphics display system and the VTIOO(Trademark) text manipulation/display system.

Software Tools for Shipbuilding Productivity

DTIC Science & Technology

1984-12-01

shipbuilding, is that design, manufacturing and robotic technology applications to shipbuilding have been proven. all aspects of shipbuilding is now a task...technical information about the process of Computer Aided Design (CAD) and Computer Aided Manufacturing (CAM) effectively has been a problem of serious and...Design (CAD) 3.4.1 CAD System Components 3.4.2 CAD System Benefits 3.4.3 New and Future CAD Technologies Computer Aided Manufacturing (CAM) 3.5.1 CAM

Student's Lab Assignments in PDE Course with MAPLE.

ERIC Educational Resources Information Center

Ponidi, B. Alhadi

Computer-aided software has been used intensively in many mathematics courses, especially in computational subjects, to solve initial value and boundary value problems in Partial Differential Equations (PDE). Many software packages were used in student lab assignments such as FORTRAN, PASCAL, MATLAB, MATHEMATICA, and MAPLE in order to accelerate…

Environmental Control System Software & Hardware Development

NASA Technical Reports Server (NTRS)

Vargas, Daniel Eduardo

2017-01-01

ECS hardware: (1) Provides controlled purge to SLS Rocket and Orion spacecraft. (2) Provide mission-focused engineering products and services. ECS software: (1) NASA requires Compact Unique Identifiers (CUIs); fixed-length identifier used to identify information items. (2) CUI structure; composed of nine semantic fields that aid the user in recognizing its purpose.

Teaching for CAD Expertise

ERIC Educational Resources Information Center

Chester, Ivan

2007-01-01

CAD (Computer Aided Design) has now become an integral part of Technology Education. The recent introduction of highly sophisticated, low-cost CAD software and CAM hardware capable of running on desktop computers has accelerated this trend. There is now quite widespread introduction of solid modeling CAD software into secondary schools but how…

Presentation Software and the Single Computer.

ERIC Educational Resources Information Center

Brown, Cindy A.

1998-01-01

Shows how the "Kid Pix" software and a single multimedia computer can aid classroom instruction for kindergarten through second grade. Topics include using the computer as a learning center for small groups of students; making a "Kid Pix" slide show; using it as an electronic chalkboard; and creating curriculum-related…

Space Station: NASA's software development approach increases safety and cost risks. Report to the Chairman, Committee on Science, Space, and Technology, House of Representatives

NASA Astrophysics Data System (ADS)

1992-06-01

The House Committee on Science, Space, and Technology asked NASA to study software development issues for the space station. How well NASA has implemented key software engineering practices for the station was asked. Specifically, the objectives were to determine: (1) if independent verification and validation techniques are being used to ensure that critical software meets specified requirements and functions; (2) if NASA has incorporated software risk management techniques into program; (3) whether standards are in place that will prescribe a disciplined, uniform approach to software development; and (4) if software support tools will help, as intended, to maximize efficiency in developing and maintaining the software. To meet the objectives, NASA proceeded: (1) reviewing and analyzing software development objectives and strategies contained in NASA conference publications; (2) reviewing and analyzing NASA, other government, and industry guidelines for establishing good software development practices; (3) reviewing and analyzing technical proposals and contracts; (4) reviewing and analyzing software management plans, risk management plans, and program requirements; (4) reviewing and analyzing reports prepared by NASA and contractor officials that identified key issues and challenges facing the program; (5) obtaining expert opinions on what constitutes appropriate independent V-and-V and software risk management activities; (6) interviewing program officials at NASA headquarters in Washington, DC; at the Space Station Program Office in Reston, Virginia; and at the three work package centers; Johnson in Houston, Texas; Marshall in Huntsville, Alabama; and Lewis in Cleveland, Ohio; and (7) interviewing contractor officials doing work for NASA at Johnson and Marshall. The audit work was performed in accordance with generally accepted government auditing standards, between April 1991 and May 1992.

An ad hoc 3D-printed tool facilitates intraesophageal suturing in experimental surgery

PubMed Central

Steinemann, D.C.; Müller, P.C.; Apitz, M.; Nickel, F.; Kenngott, H.G.; Müller-Stich, B.P.; Linke, G.R.

2018-01-01

Background Three-dimensional printing (3DP) has become popular for development of anatomic models, preoperative planning, and production of tailored implants. A novel laparoscopic, transgastric procedure for distal esophageal mucosectomy was developed. During this procedure a space holder had to be introduced into the distal esophagus for exposure during suturing. The production process and evaluation of a 3DP space holder are described herein. Material and methods Computer-aided design software was used to develop models printed from polylactic acid. The prototype was adapted after testing in a cadaveric model. Subsequently the device was evaluated in a non-survival porcine model. A mucosal purse-string suture was placed as orally as possible in the esophagus, in the intervention group with and in the control group without use of the tool (n=8 each). The distance of the stitches from the Z-line was measured. The variability of stitches indicated the suture quality. Results The median maximum distance from Z-line to purse-string suture was larger in the intervention group (5.0 [3.3-6.4] versus 2.4 [2.0-4.1] cm;P=0.013). The time taken to place the sutures was shorter in the control group (P<0.001). Stitch variance tended to be greater in the intervention group (2.3 [0.9-2.5] versus 0.7 [0.2-0.4] cm;P=0.051). The time required for design and production of a tailored tool was below 24 h. Conclusions 3DP in experimental surgery enables rapid production, permits repeated adaptation until a tailored tool is obtained, and ensures independence from industrial partners. With the aid of the space holder more orally located esophageal lesions came within reach. PMID:29433890

Computational System For Rapid CFD Analysis In Engineering

NASA Technical Reports Server (NTRS)

Barson, Steven L.; Ascoli, Edward P.; Decroix, Michelle E.; Sindir, Munir M.

1995-01-01

Computational system comprising modular hardware and software sub-systems developed to accelerate and facilitate use of techniques of computational fluid dynamics (CFD) in engineering environment. Addresses integration of all aspects of CFD analysis process, including definition of hardware surfaces, generation of computational grids, CFD flow solution, and postprocessing. Incorporates interfaces for integration of all hardware and software tools needed to perform complete CFD analysis. Includes tools for efficient definition of flow geometry, generation of computational grids, computation of flows on grids, and postprocessing of flow data. System accepts geometric input from any of three basic sources: computer-aided design (CAD), computer-aided engineering (CAE), or definition by user.

14 CFR 382.131 - Do baggage liability limits apply to mobility aids and other assistive devices?

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 4 2011-01-01 2011-01-01 false Do baggage liability limits apply to mobility aids and other assistive devices? 382.131 Section 382.131 Aeronautics and Space OFFICE OF THE... BASIS OF DISABILITY IN AIR TRAVEL Stowage of Wheelchairs, Other Mobility Aids, and Other Assistive...

14 CFR 382.131 - Do baggage liability limits apply to mobility aids and other assistive devices?

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Do baggage liability limits apply to mobility aids and other assistive devices? 382.131 Section 382.131 Aeronautics and Space OFFICE OF THE... BASIS OF DISABILITY IN AIR TRAVEL Stowage of Wheelchairs, Other Mobility Aids, and Other Assistive...

Web-Based Software for Managing Research

NASA Technical Reports Server (NTRS)

Hoadley, Sherwood T.; Ingraldi, Anthony M.; Gough, Kerry M.; Fox, Charles; Cronin, Catherine K.; Hagemann, Andrew G.; Kemmerly, Guy T.; Goodman, Wesley L.

2007-01-01

aeroCOMPASS is a software system, originally designed to aid in the management of wind tunnels at Langley Research Center, that could be adapted to provide similar aid to other enterprises in which research is performed in common laboratory facilities by users who may be geographically dispersed. Included in aeroCOMPASS is Web-interface software that provides a single, convenient portal to a set of project- and test-related software tools and other application programs. The heart of aeroCOMPASS is a user-oriented document-management software subsystem that enables geographically dispersed users to easily share and manage a variety of documents. A principle of "write once, read many" is implemented throughout aeroCOMPASS to eliminate the need for multiple entry of the same information. The Web framework of aeroCOMPASS provides links to client-side application programs that are fully integrated with databases and server-side application programs. Other subsystems of aeroCOMPASS include ones for reserving hardware, tracking of requests and feedback from users, generating interactive notes, administration of a customer-satisfaction questionnaire, managing execution of tests, managing archives of metadata about tests, planning tests, and providing online help and instruction for users.

36 CFR 1192.83 - Mobility aid accessibility.

Code of Federal Regulations, 2014 CFR

2014-07-01

... areas, each with a minimum clear floor space of 48 inches by 30 inches, which do not unduly restrict passenger flow. Space to accommodate wheelchairs and mobility aids may be provided within the normal area used by standees and designation of specific spaces is not required. (2) Exception. If lifts, ramps or...

36 CFR 1192.83 - Mobility aid accessibility.

Code of Federal Regulations, 2012 CFR

2012-07-01

... areas, each with a minimum clear floor space of 48 inches by 30 inches, which do not unduly restrict passenger flow. Space to accommodate wheelchairs and mobility aids may be provided within the normal area used by standees and designation of specific spaces is not required. (2) Exception. If lifts, ramps or...

Space-Shuttle Emulator Software

NASA Technical Reports Server (NTRS)

Arnold, Scott; Askew, Bill; Barry, Matthew R.; Leigh, Agnes; Mermelstein, Scott; Owens, James; Payne, Dan; Pemble, Jim; Sollinger, John; Thompson, Hiram;

Investigating the probability of detection of typical cavity shapes through modelling and comparison of geophysical techniques

NASA Astrophysics Data System (ADS)

James, P.

2011-12-01

With a growing need for housing in the U.K., the government has proposed increased development of brownfield sites. However, old mine workings and natural cavities represent a potential hazard before, during and after construction on such sites, and add further complication to subsurface parameters. Cavities are hence a limitation to certain redevelopment and their detection is an ever important consideration. The current standard technique for cavity detection is a borehole grid, which is intrusive, non-continuous, slow and expensive. A new robust investigation standard in the detection of cavities is sought and geophysical techniques offer an attractive alternative. Geophysical techniques have previously been utilised successfully in the detection of cavities in various geologies, but still has an uncertain reputation in the engineering industry. Engineers are unsure of the techniques and are inclined to rely on well known techniques than utilise new technologies. Bad experiences with geophysics are commonly due to the indiscriminate choice of particular techniques. It is imperative that a geophysical survey is designed with the specific site and target in mind at all times, and the ability and judgement to rule out some, or all, techniques. To this author's knowledge no comparative software exists to aid technique choice. Also, previous modelling software limit the shapes of bodies and hence typical cavity shapes are not represented. Here, we introduce 3D modelling software (Matlab) which computes and compares the response to various cavity targets from a range of techniques (gravity, gravity gradient, magnetic, magnetic gradient and GPR). Typical near surface cavity shapes are modelled including shafts, bellpits, various lining and capping materials, and migrating voids. The probability of cavity detection is assessed in typical subsurface and noise conditions across a range of survey parameters. Techniques can be compared and the limits of detection distance assessed. The density of survey points required to achieve a required probability of detection can be calculated. The software aids discriminate choice of technique, improves survey design, and increases the likelihood of survey success; all factors sought in the engineering industry. As a simple example, the response from magnetometry, gravimetry, and gravity gradient techniques above an example 3m deep, 1m cube air cavity in limestone across a 15m grid was calculated. The maximum responses above the cavity are small (amplitudes of 0.018nT, 0.0013mGal, 8.3eotvos respectively), but at typical site noise levels the detection reliability is over 50% for the gradient gravity method on a single survey line. Increasing the number of survey points across the site increases the reliability of detection of the anomaly by the addition of probabilities. We can calculate the probability of detection at different profile spacings to assess the best possible survey design. At 1m spacing the overall probability of by the gradient gravity method is over 90%, and over 60% for magnetometry (at 3m spacing the probability drops to 32%). The use of modelling in near surface surveys is a useful tool to assess the feasibility of a range of techniques to detect subtle signals. Future work will integrate this work with borehole measured parameters.

The NASA computer aided design and test system

NASA Technical Reports Server (NTRS)

Gould, J. M.; Juergensen, K.

1973-01-01

A family of computer programs facilitating the design, layout, evaluation, and testing of digital electronic circuitry is described. CADAT (computer aided design and test system) is intended for use by NASA and its contractors and is aimed predominantly at providing cost effective microelectronic subsystems based on custom designed metal oxide semiconductor (MOS) large scale integrated circuits (LSIC's). CADAT software can be easily adopted by installations with a wide variety of computer hardware configurations. Its structure permits ease of update to more powerful component programs and to newly emerging LSIC technologies. The components of the CADAT system are described stressing the interaction of programs rather than detail of coding or algorithms. The CADAT system provides computer aids to derive and document the design intent, includes powerful automatic layout software, permits detailed geometry checks and performance simulation based on mask data, and furnishes test pattern sequences for hardware testing.

Static and Dynamic Verification of Critical Software for Space Applications

NASA Astrophysics Data System (ADS)

Moreira, F.; Maia, R.; Costa, D.; Duro, N.; Rodríguez-Dapena, P.; Hjortnaes, K.

Space technology is no longer used only for much specialised research activities or for sophisticated manned space missions. Modern society relies more and more on space technology and applications for every day activities. Worldwide telecommunications, Earth observation, navigation and remote sensing are only a few examples of space applications on which we rely daily. The European driven global navigation system Galileo and its associated applications, e.g. air traffic management, vessel and car navigation, will significantly expand the already stringent safety requirements for space based applications Apart from their usefulness and practical applications, every single piece of onboard software deployed into the space represents an enormous investment. With a long lifetime operation and being extremely difficult to maintain and upgrade, at least when comparing with "mainstream" software development, the importance of ensuring their correctness before deployment is immense. Verification &Validation techniques and technologies have a key role in ensuring that the onboard software is correct and error free, or at least free from errors that can potentially lead to catastrophic failures. Many RAMS techniques including both static criticality analysis and dynamic verification techniques have been used as a means to verify and validate critical software and to ensure its correctness. But, traditionally, these have been isolated applied. One of the main reasons is the immaturity of this field in what concerns to its application to the increasing software product(s) within space systems. This paper presents an innovative way of combining both static and dynamic techniques exploiting their synergy and complementarity for software fault removal. The methodology proposed is based on the combination of Software FMEA and FTA with Fault-injection techniques. The case study herein described is implemented with support from two tools: The SoftCare tool for the SFMEA and SFTA, and the Xception tool for fault-injection. Keywords: Verification &Validation, RAMS, Onboard software, SFMEA, STA, Fault-injection 1 This work is being performed under the project STADY Applied Static And Dynamic Verification Of Critical Software, ESA/ESTEC Contract Nr. 15751/02/NL/LvH.

Computer Aided Phenomenography: The Role of Leximancer Computer Software in Phenomenographic Investigation

ERIC Educational Resources Information Center

Penn-Edwards, Sorrel

2010-01-01

The qualitative research methodology of phenomenography has traditionally required a manual sorting and analysis of interview data. In this paper I explore a potential means of streamlining this procedure by considering a computer aided process not previously reported upon. Two methods of lexicological analysis, manual and automatic, were examined…

Computer-Aided College Algebra: Learning Components that Students Find Beneficial

ERIC Educational Resources Information Center

Aichele, Douglas B.; Francisco, Cynthia; Utley, Juliana; Wescoatt, Benjamin

2011-01-01

A mixed-method study was conducted during the Fall 2008 semester to better understand the experiences of students participating in computer-aided instruction of College Algebra using the software MyMathLab. The learning environment included a computer learning system for the majority of the instruction, a support system via focus groups (weekly…

Concerned Technology 1989: Electronic Aids for People with Special Needs.

ERIC Educational Resources Information Center

Sandhu, Jim Singh; Richardson, Steve

In light of the implementation of Section 508 of the Rehabilitation Amendments Act of 1986 requiring that all electronic equipment purchased by the U.S. Government be accesible to the handicapped. this directory lists several hundred electronic aids for the disabled. The introduction humorously reviews the state of the art in software, artificial…

Microcomputers in Schools as a Teaching and Learning Aid.

ERIC Educational Resources Information Center

Trotman-Dickenson, D. I.

1986-01-01

Presents the findings of a survey of comprehensive and independent schools' use of microcomputers as teaching and learning aids in economics. Results suggest that use is wide spread but not intensive. Teachers allocate few hours to computer programs per year, have difficulty finding suitable software, and fail to encourage use by girls. (JDH)

Computer Aided Instruction: A Study of Student Evaluations and Academic Performance

ERIC Educational Resources Information Center

Collins, David; Deck, Alan; McCrickard, Myra

2008-01-01

Computer aided instruction (CAI) encompasses a broad range of computer technologies that supplement the classroom learning environment and can dramatically increase a student's access to information. Criticism of CAI generally focuses on two issues: it lacks an adequate foundation in educational theory and the software is difficult to implement…

FORCHECK -- A Fortran Verifier and Programming Aid

NASA Astrophysics Data System (ADS)

Lawden, M. D.

FORCHECK is a Fortran verifier and programming aid which has been purchased from Polyhedron software and installed on the Starlink Database computer (STADAT) for the use of all Starlink users. It was developed by Erik W. Kruyt at Leiden University. It is only available on STADAT and is not installed on any other Starlink nodes.

National Science Foundation 1989 Engineering Senior Design Projects To Aid the Disabled.

ERIC Educational Resources Information Center

Enderle, John D., Ed.

Through the Bioengineering and Research to Aid the Disabled program of the National Science Foundation, design projects were awarded competitively to 16 universities. Senior engineering students at each of the universities constructed custom devices and software for disabled individuals. This compendium contains a description of each project in…

Music and hearing aids--an introduction.

PubMed

Chasin, Marshall

2012-09-01

Modern digital hearing aids have provided improved fidelity over those of earlier decades for speech. The same however cannot be said for music. Most modern hearing aids have a limitation of their "front end," which comprises the analog-to-digital (A/D) converter. For a number of reasons, the spectral nature of music as an input to a hearing aid is beyond the optimal operating conditions of the "front end" components. Amplified music tends to be of rather poor fidelity. Once the music signal is distorted, no amount of software manipulation that occurs later in the circuitry can improve things. The solution is not a software issue. Some characteristics of music that make it difficult to be transduced without significant distortion include an increased sound level relative to that of speech, and the crest factor- the difference in dB between the instantaneous peak of a signal and its RMS value. Clinical strategies and technical innovations have helped to improve the fidelity of amplified music and these include a reduction of the level of the input that is presented to the A/D converter.

Facilitating text reading in posterior cortical atrophy.

PubMed

Yong, Keir X X; Rajdev, Kishan; Shakespeare, Timothy J; Leff, Alexander P; Crutch, Sebastian J

2015-07-28

We report (1) the quantitative investigation of text reading in posterior cortical atrophy (PCA), and (2) the effects of 2 novel software-based reading aids that result in dramatic improvements in the reading ability of patients with PCA. Reading performance, eye movements, and fixations were assessed in patients with PCA and typical Alzheimer disease and in healthy controls (experiment 1). Two reading aids (single- and double-word) were evaluated based on the notion that reducing the spatial and oculomotor demands of text reading might support reading in PCA (experiment 2). Mean reading accuracy in patients with PCA was significantly worse (57%) compared with both patients with typical Alzheimer disease (98%) and healthy controls (99%); spatial aspects of passages were the primary determinants of text reading ability in PCA. Both aids led to considerable gains in reading accuracy (PCA mean reading accuracy: single-word reading aid = 96%; individual patient improvement range: 6%-270%) and self-rated measures of reading. Data suggest a greater efficiency of fixations and eye movements under the single-word reading aid in patients with PCA. These findings demonstrate how neurologic characterization of a neurodegenerative syndrome (PCA) and detailed cognitive analysis of an important everyday skill (reading) can combine to yield aids capable of supporting important everyday functional abilities. This study provides Class III evidence that for patients with PCA, 2 software-based reading aids (single-word and double-word) improve reading accuracy. © 2015 American Academy of Neurology.

Facilitating text reading in posterior cortical atrophy

PubMed Central

Rajdev, Kishan; Shakespeare, Timothy J.; Leff, Alexander P.; Crutch, Sebastian J.

2015-01-01

Objective: We report (1) the quantitative investigation of text reading in posterior cortical atrophy (PCA), and (2) the effects of 2 novel software-based reading aids that result in dramatic improvements in the reading ability of patients with PCA. Methods: Reading performance, eye movements, and fixations were assessed in patients with PCA and typical Alzheimer disease and in healthy controls (experiment 1). Two reading aids (single- and double-word) were evaluated based on the notion that reducing the spatial and oculomotor demands of text reading might support reading in PCA (experiment 2). Results: Mean reading accuracy in patients with PCA was significantly worse (57%) compared with both patients with typical Alzheimer disease (98%) and healthy controls (99%); spatial aspects of passages were the primary determinants of text reading ability in PCA. Both aids led to considerable gains in reading accuracy (PCA mean reading accuracy: single-word reading aid = 96%; individual patient improvement range: 6%–270%) and self-rated measures of reading. Data suggest a greater efficiency of fixations and eye movements under the single-word reading aid in patients with PCA. Conclusions: These findings demonstrate how neurologic characterization of a neurodegenerative syndrome (PCA) and detailed cognitive analysis of an important everyday skill (reading) can combine to yield aids capable of supporting important everyday functional abilities. Classification of evidence: This study provides Class III evidence that for patients with PCA, 2 software-based reading aids (single-word and double-word) improve reading accuracy. PMID:26138948

Computer-aided system design

NASA Technical Reports Server (NTRS)

Walker, Carrie K.

1991-01-01

A technique has been developed for combining features of a systems architecture design and assessment tool and a software development tool. This technique reduces simulation development time and expands simulation detail. The Architecture Design and Assessment System (ADAS), developed at the Research Triangle Institute, is a set of computer-assisted engineering tools for the design and analysis of computer systems. The ADAS system is based on directed graph concepts and supports the synthesis and analysis of software algorithms mapped to candidate hardware implementations. Greater simulation detail is provided by the ADAS functional simulator. With the functional simulator, programs written in either Ada or C can be used to provide a detailed description of graph nodes. A Computer-Aided Software Engineering tool developed at the Charles Stark Draper Laboratory (CSDL CASE) automatically generates Ada or C code from engineering block diagram specifications designed with an interactive graphical interface. A technique to use the tools together has been developed, which further automates the design process.

STRS SpaceWire FPGA Module

NASA Technical Reports Server (NTRS)

Lux, James P.; Taylor, Gregory H.; Lang, Minh; Stern, Ryan A.

2011-01-01

An FPGA module leverages the previous work from Goddard Space Flight Center (GSFC) relating to NASA s Space Telecommunications Radio System (STRS) project. The STRS SpaceWire FPGA Module is written in the Verilog Register Transfer Level (RTL) language, and it encapsulates an unmodified GSFC core (which is written in VHDL). The module has the necessary inputs/outputs (I/Os) and parameters to integrate seamlessly with the SPARC I/O FPGA Interface module (also developed for the STRS operating environment, OE). Software running on the SPARC processor can access the configuration and status registers within the SpaceWire module. This allows software to control and monitor the SpaceWire functions, but it is also used to give software direct access to what is transmitted and received through the link. SpaceWire data characters can be sent/received through the software interface, as well as through the dedicated interface on the GSFC core. Similarly, SpaceWire time codes can be sent/received through the software interface or through a dedicated interface on the core. This innovation is designed for plug-and-play integration in the STRS OE. The SpaceWire module simplifies the interfaces to the GSFC core, and synchronizes all I/O to a single clock. An interrupt output (with optional masking) identifies time-sensitive events within the module. Test modes were added to allow internal loopback of the SpaceWire link and internal loopback of the client-side data interface.

NASA Operational Simulator for Small Satellites: Tools for Software Based Validation and Verification of Small Satellites

NASA Technical Reports Server (NTRS)

Grubb, Matt

2016-01-01

The NASA Operational Simulator for Small Satellites (NOS3) is a suite of tools to aid in areas such as software development, integration test (IT), mission operations training, verification and validation (VV), and software systems check-out. NOS3 provides a software development environment, a multi-target build system, an operator interface-ground station, dynamics and environment simulations, and software-based hardware models. NOS3 enables the development of flight software (FSW) early in the project life cycle, when access to hardware is typically not available. For small satellites there are extensive lead times on many of the commercial-off-the-shelf (COTS) components as well as limited funding for engineering test units (ETU). Considering the difficulty of providing a hardware test-bed to each developer tester, hardware models are modeled based upon characteristic data or manufacturers data sheets for each individual component. The fidelity of each hardware models is such that FSW executes unaware that physical hardware is not present. This allows binaries to be compiled for both the simulation environment, and the flight computer, without changing the FSW source code. For hardware models that provide data dependent on the environment, such as a GPS receiver or magnetometer, an open-source tool from NASA GSFC (42 Spacecraft Simulation) is used to provide the necessary data. The underlying infrastructure used to transfer messages between FSW and the hardware models can also be used to monitor, intercept, and inject messages, which has proven to be beneficial for VV of larger missions such as James Webb Space Telescope (JWST). As hardware is procured, drivers can be added to the environment to enable hardware-in-the-loop (HWIL) testing. When strict time synchronization is not vital, any number of combinations of hardware components and software-based models can be tested. The open-source operator interface used in NOS3 is COSMOS from Ball Aerospace. For testing, plug-ins are implemented in COSMOS to control the NOS3 simulations, while the command and telemetry tools available in COSMOS are used to communicate with FSW. NOS3 is actively being used for FSW development and component testing of the Simulation-to-Flight 1 (STF-1) CubeSat. As NOS3 matures, hardware models have been added for common CubeSat components such as Novatel GPS receivers, ClydeSpace electrical power systems and batteries, ISISpace antenna systems, etc. In the future, NASA IVV plans to distribute NOS3 to other CubeSat developers and release the suite to the open-source community.

Prevention of AIDS and living together with an HIV-infected patient.

PubMed

Fahik, F T; Reichert, M C; Gabriel, R; Marin, H F

1995-01-01

In Brazil, approximately 45 thousand cases had been reported until the end of 1993, with an estimated 50% underreport. According to the Ministry of Health, until the year 2,000 from 2 to 8 million Brazilians citizens will be infected with HIV. The basic aspect of the educational campaigns regarding AIDS does not refer only to information on forms of transmission and prevention measures, but also attempts to fight against the mystification and the enormous resistance of the public to definitely accept the fact that transmission does not occur by simple means such as having a drink from the same glass, independently of its socioeconomic and cultural level. In addition to the lack of information, prejudice and discrimination appear strongly rooted in the population to the point of a tendency of social and effective rejection of the HIV-infected patient. Fighting against prejudice, against which there is also no vaccine, is a task as gigantic as fighting against the virus. For both, investments in education of and information to the population in general, is very important. Development of a software which would fulfill the function of explaining, and providing the correct information about AIDS, would be extremely valuable for any part of the society and could also be used as a complementary element by health professionals. The objective was to develop an interactive software in order to demonstrate prevention measures and universal precaution in AIDS; to inform about the necessary care to people that are living together an HIV-infected patient. To develop this software with animation and elucidating text regarding AIDS for the general population, we are using the Storyboard live to be run in Windows environment.

The Assistant for Specifying the Quality Software (ASQS) Operational Concept Document. Volume 1

DTIC Science & Technology

1990-09-01

Assistant in which the manager supplies system-specific characteristics and needs and the Assistant fills in the software quality concepts and methods. The...member(s) of the Computer Resources Working Group (CRWG) to aid in performing a software quality engineering study. Figure 3.4-1 outlines the...need to recovery from faults more likely than need _o provide alternative functions or interfaces), and more on Autcncmy - 27 - that Modularity

An Interactive and Automated Software Development Environment.

DTIC Science & Technology

1982-12-01

four levels. Each DFD has an accompanying textual description to aid the reader in understanding the diagram. Both the data flows and the operations...students using the SDW for major software developments. Students in the software engineering courses use the SDW as a pedagogical tool for learning the...the SDWE. For thiz reason, the modified SDWE Algorithmic Design is included as Appendix F. 172 Ui 4.4 Desigin RL the ProQiect Data Baes The Project

Modeling and analysis of selected space station communications and tracking subsystems

NASA Technical Reports Server (NTRS)

Richmond, Elmer Raydean

1993-01-01

The Communications and Tracking System on board Space Station Freedom (SSF) provides space-to-ground, space-to-space, audio, and video communications, as well as tracking data reception and processing services. Each major category of service is provided by a communications subsystem which is controlled and monitored by software. Among these subsystems, the Assembly/Contingency Subsystem (ACS) and the Space-to-Ground Subsystem (SGS) provide communications with the ground via the Tracking and Data Relay Satellite (TDRS) System. The ACS is effectively SSF's command link, while the SGS is primarily intended as the data link for SSF payloads. The research activities of this project focused on the ACS and SGS antenna management algorithms identified in the Flight System Software Requirements (FSSR) documentation, including: (1) software modeling and evaluation of antenna management (positioning) algorithms; and (2) analysis and investigation of selected variables and parameters of these antenna management algorithms i.e., descriptions and definitions of ranges, scopes, and dimensions. In a related activity, to assist those responsible for monitoring the development of this flight system software, a brief summary of software metrics concepts, terms, measures, and uses was prepared.

CARDS: A blueprint and environment for domain-specific software reuse

NASA Technical Reports Server (NTRS)

Wallnau, Kurt C.; Solderitsch, Anne Costa; Smotherman, Catherine

1992-01-01

CARDS (Central Archive for Reusable Defense Software) exploits advances in domain analysis and domain modeling to identify, specify, develop, archive, retrieve, understand, and reuse domain-specific software components. An important element of CARDS is to provide visibility into the domain model artifacts produced by, and services provided by, commercial computer-aided software engineering (CASE) technology. The use of commercial CASE technology is important to provide rich, robust support for the varied roles involved in a reuse process. We refer to this kind of use of knowledge representation systems as supporting 'knowledge-based integration.'

Computer-aided design and computer science technology

NASA Technical Reports Server (NTRS)

Fulton, R. E.; Voigt, S. J.

1976-01-01

A description is presented of computer-aided design requirements and the resulting computer science advances needed to support aerospace design. The aerospace design environment is examined, taking into account problems of data handling and aspects of computer hardware and software. The interactive terminal is normally the primary interface between the computer system and the engineering designer. Attention is given to user aids, interactive design, interactive computations, the characteristics of design information, data management requirements, hardware advancements, and computer science developments.

Youth, AIDS, and HIV. Resources for Educators and Policymakers, 1999-2000. A Directory of Selected National, State, and Local Resources, and an Annotated Resource Listing of Audiovisual, Print, and Software Materials for AIDS Education and HIV Prevention. Bulletin No. 99218.

ERIC Educational Resources Information Center

Wisconsin State Dept. of Public Instruction, Madison.

This resource document provides information about technical assistance and educational materials that can guide the development, implementation, and evaluation of acquired immunodeficiency syndrome (AIDS) education. The resources also offer information about programs whose goals are to prevent the spread of human immunodeficiency virus (HIV) and…

36 CFR § 1192.83 - Mobility aid accessibility.

Code of Federal Regulations, 2013 CFR

2013-07-01

... users to reach areas, each with a minimum clear floor space of 48 inches by 30 inches, which do not unduly restrict passenger flow. Space to accommodate wheelchairs and mobility aids may be provided within the normal area used by standees and designation of specific spaces is not required. (2) Exception. If...

STRS Radio Service Software for NASA's SCaN Testbed

NASA Technical Reports Server (NTRS)

Mortensen, Dale J.; Bishop, Daniel Wayne; Chelmins, David T.

2012-01-01

NASAs Space Communication and Navigation(SCaN) Testbed was launched to the International Space Station in 2012. The objective is to promote new software defined radio technologies and associated software application reuse, enabled by this first flight of NASAs Space Telecommunications Radio System(STRS) architecture standard. Pre-launch testing with the testbeds software defined radios was performed as part of system integration. Radio services for the JPL SDR were developed during system integration to allow the waveform application to operate properly in the space environment, especially considering thermal effects. These services include receiver gain control, frequency offset, IQ modulator balance, and transmit level control. Development, integration, and environmental testing of the radio services will be described. The added software allows the waveform application to operate properly in the space environment, and can be reused by future experimenters testing different waveform applications. Integrating such services with the platform provided STRS operating environment will attract more users, and these services are candidates for interface standardization via STRS.

STRS Radio Service Software for NASA's SCaN Testbed

NASA Technical Reports Server (NTRS)

Mortensen, Dale J.; Bishop, Daniel Wayne; Chelmins, David T.

2013-01-01

NASA's Space Communication and Navigation(SCaN) Testbed was launched to the International Space Station in 2012. The objective is to promote new software defined radio technologies and associated software application reuse, enabled by this first flight of NASA's Space Telecommunications Radio System (STRS) architecture standard. Pre-launch testing with the testbed's software defined radios was performed as part of system integration. Radio services for the JPL SDR were developed during system integration to allow the waveform application to operate properly in the space environment, especially considering thermal effects. These services include receiver gain control, frequency offset, IQ modulator balance, and transmit level control. Development, integration, and environmental testing of the radio services will be described. The added software allows the waveform application to operate properly in the space environment, and can be reused by future experimenters testing different waveform applications. Integrating such services with the platform provided STRS operating environment will attract more users, and these services are candidates for interface standardization via STRS.

NASA Data Acquisitions System (NDAS) Software Architecture

NASA Technical Reports Server (NTRS)

Davis, Dawn; Duncan, Michael; Franzl, Richard; Holladay, Wendy; Marshall, Peggi; Morris, Jon; Turowski, Mark

2012-01-01

The NDAS Software Project is for the development of common low speed data acquisition system software to support NASA's rocket propulsion testing facilities at John C. Stennis Space Center (SSC), White Sands Test Facility (WSTF), Plum Brook Station (PBS), and Marshall Space Flight Center (MSFC).

Space Shuttle Software Development and Certification

NASA Technical Reports Server (NTRS)

Orr, James K.; Henderson, Johnnie A

2000-01-01

Man-rated software, "software which is in control of systems and environments upon which human life is critically dependent," must be highly reliable. The Space Shuttle Primary Avionics Software System is an excellent example of such a software system. Lessons learn from more than 20 years of effort have identified basic elements that must be present to achieve this high degree of reliability. The elements include rigorous application of appropriate software development processes, use of trusted tools to support those processes, quantitative process management, and defect elimination and prevention. This presentation highlights methods used within the Space Shuttle project and raises questions that must be addressed to provide similar success in a cost effective manner on future long-term projects where key application development tools are COTS rather than internally developed custom application development tools

Computer Simulation Modeling: A Method for Predicting the Utilities of Alternative Computer-Aided Treat Evaluation Algorithms

DTIC Science & Technology

1990-09-01

1988). Current versions of the ADATS have CATE systems insLzlled, but the software is still under development by the radar manufacturer, Contraves ...Italiana, a subcontractor to Martin Marietta (USA). Contraves Italiana will deliver the final version of the software to Martin Marietta in 1991. Until then

Digital Tools: Enhancing Painting Skills among Malaysian Secondary School Students

ERIC Educational Resources Information Center

Samah, Azimah A.; Putih, Abu Talib; Hussin, Zaharah

2016-01-01

Digital tools refer to software applications in the production of artworks particularly in painting. Digital art work is materialized by using computers, software and a combination of computer peripherals such as tablet support. With the aid of electronic equipment, digital artists manipulate pixels or coloring with light to compose the work and…

Using Software Tools to Automate the Assessment of Student Programs.

ERIC Educational Resources Information Center

Jackson, David

1991-01-01

Argues that advent of computer-aided instruction (CAI) systems for teaching introductory computer programing makes it imperative that software be developed to automate assessment and grading of student programs. Examples of typical student programing problems are given, and application of the Unix tools Lex and Yacc to the automatic assessment of…

Using Articulate Virtual Laboratories in Teaching Energy Conversion at the U.S. Naval Academy.

ERIC Educational Resources Information Center

Wu, C.

1998-01-01

The Mechanical Engineering Department at the U.S. Naval Academy is currently evaluating a new teaching method which uses computer software. Utilizing the thermodynamic-based software CyclePad, Intelligent Computer Aided Instruction is incorporated in an advanced energy conversion course for Mechanical Engineering students. The CyclePad software…

Extended System Operations Studies for Automated Guideway Transit Systems : Procedure for the Analysis of Representative AGT Deployments

DOT National Transportation Integrated Search

1981-12-01

The purpose of this report is to present a general procedure for using the SOS software to analyze AGT systems. Data to aid the analyst in specifying input information, required as input to the software, are summarized in the appendices. The data are...

Use of an Automatic Problem Generator to Teach Basic Skills in a First Course in Assembly Language.

ERIC Educational Resources Information Center

Benander, Alan; And Others

1989-01-01

Discussion of the use of computer aided instruction (CAI) and instructional software in college level courses highlights an automatic problem generator, AUTOGEN, that was written for computer science students learning assembly language. Design of the software is explained, and student responses are reported. (nine references) (LRW)

The large scale microelectronics Computer-Aided Design and Test (CADAT) system

NASA Technical Reports Server (NTRS)

Gould, J. M.

1978-01-01

The CADAT system consists of a number of computer programs written in FORTRAN that provide the capability to simulate, lay out, analyze, and create the artwork for large scale microelectronics. The function of each software component of the system is described with references to specific documentation for each software component.

A Study of the Use of Ontologies for Building Computer-Aided Control Engineering Self-Learning Educational Software

NASA Astrophysics Data System (ADS)

García, Isaías; Benavides, Carmen; Alaiz, Héctor; Alonso, Angel

2013-08-01

This paper describes research on the use of knowledge models (ontologies) for building computer-aided educational software in the field of control engineering. Ontologies are able to represent in the computer a very rich conceptual model of a given domain. This model can be used later for a number of purposes in different software applications. In this study, domain ontology about the field of lead-lag compensator design has been built and used for automatic exercise generation, graphical user interface population and interaction with the user at any level of detail, including explanations about why things occur. An application called Onto-CELE (ontology-based control engineering learning environment) uses the ontology for implementing a learning environment that can be used for self and lifelong learning purposes. The experience has shown that the use of knowledge models as the basis for educational software applications is capable of showing students the whole complexity of the analysis and design processes at any level of detail. A practical experience with postgraduate students has shown the mentioned benefits and possibilities of the approach.

PUS Services Software Building Block Automatic Generation for Space Missions

NASA Astrophysics Data System (ADS)

Candia, S.; Sgaramella, F.; Mele, G.

2008-08-01

The Packet Utilization Standard (PUS) has been specified by the European Committee for Space Standardization (ECSS) and issued as ECSS-E-70-41A to define the application-level interface between Ground Segments and Space Segments. The ECSS-E- 70-41A complements the ECSS-E-50 and the Consultative Committee for Space Data Systems (CCSDS) recommendations for packet telemetry and telecommand. The ECSS-E-70-41A characterizes the identified PUS Services from a functional point of view and the ECSS-E-70-31 standard specifies the rules for their mission-specific tailoring. The current on-board software design for a space mission implies the production of several PUS terminals, each providing a specific tailoring of the PUS services. The associated on-board software building blocks are developed independently, leading to very different design choices and implementations even when the mission tailoring requires very similar services (from the Ground operative perspective). In this scenario, the automatic production of the PUS services building blocks for a mission would be a way to optimize the overall mission economy and improve the robusteness and reliability of the on-board software and of the Ground-Space interactions. This paper presents the Space Software Italia (SSI) activities for the development of an integrated environment to support: the PUS services tailoring activity for a specific mission. the mission-specific PUS services configuration. the generation the UML model of the software building block implementing the mission-specific PUS services and the related source code, support documentation (software requirements, software architecture, test plans/procedures, operational manuals), and the TM/TC database. The paper deals with: (a) the project objectives, (b) the tailoring, configuration, and generation process, (c) the description of the environments supporting the process phases, (d) the characterization of the meta-model used for the generation, (e) the characterization of the reference avionics architecture and of the reference on- board software high-level architecture.

Software-Based Safety Systems in Space - Learning from other Domains

NASA Astrophysics Data System (ADS)

Klicker, M.; Putzer, H.

2012-01-01

Increasing complexity and new emerging capabilities for manned and unmanned missions have been the hallmark of the past decades of space exploration. One of the drivers in this process was the ever increasing use of software and software-intensive systems to implement system functions necessary to the capabilities needed. The course of technological evolution suggests that this development will continue well into the future with a number of challenges for the safety community some of which shall be discussed in this paper. The current state of the art reveals a number of problems with developing and assessing safety critical software which explains the reluctance of the space community to rely on software-based safety measures to mitigate hazards. Among others, usually lack of trustworthy evidence of software integrity in all foreseeable situations and the difficulties to integrate software in the traditional safety analysis framework are cited. Experience from other domains and recent developments in modern software development methodologies and verification techniques are analysed for the suitability for space systems and an avionics architectural framework (see STANAG 4626) for the implementation of safety critical software is proposed. This is shown to create among other features the possibility of numerous degradation modes enhancing overall system safety and interoperability of computerized space systems. It also potentially simplifies international cooperation on a technical level by introducing a higher degree of compatibility. As software safety cannot be tested or argued into a system in hindsight, the development process and especially the architecture chosen are essential to establish safety properties for the software used to implement safety functions. The core of the safety argument revolves around the separation of different functions and software modules from each other by minimal coupling of functions and credible separation mechanisms in the architecture combined with rigorous development methodologies for the software itself.

Optical metrology at the Optical Sciences Center: an historical review

NASA Astrophysics Data System (ADS)

Creath, Katherine; Parks, Robert E.

2014-10-01

The Optical Sciences Center (OSC) begun as a graduate-level applied optics teaching institution to support the US space effort. The making of optics representative of those used in other space programs was deemed essential. This led to the need for optical metrology: at first Hartmann tests, but almost immediately to interferometric tests using the newly invented HeNe laser. Not only were new types of interferometers needed, but the whole infrastructure that went with testing, fringe location methods, aberration removal software and contour map generation to aid the opticians during polishing needed to be developed. Over the last half century more rapid and precise methods of interferogram data reduction, surface roughness measurement, and methods of instrument calibration to separate errors from those in the optic have been pioneered at OSC. Other areas of research included null lens design and the writing of lens design software that led into the design of computer generated holograms for asphere testing. More recently work has been done on the reduction of speckle noise in interferograms, methods to test large convex aspheres, and a return to slope measuring tests to increase the dynamic range of the types of aspheric surfaces amenable to optical testing including free-form surfaces. This paper documents the history of the development of optical testing projects at OSC and highlights the contributions some of the individuals associated with new methods of testing and the infrastructure needed to support the testing. We conclude with comments about the future trends optical metrology.

Use of Human Modeling Simulation Software in the Task Analysis of the Environmental Control and Life Support System Component Installation Procedures

NASA Technical Reports Server (NTRS)

Estes, Samantha; Parker, Nelson C. (Technical Monitor)

2001-01-01

Virtual reality and simulation applications are becoming widespread in human task analysis. These programs have many benefits for the Human Factors Engineering field. Not only do creating and using virtual environments for human engineering analyses save money and time, this approach also promotes user experimentation and provides increased quality of analyses. This paper explains the human engineering task analysis performed on the Environmental Control and Life Support System (ECLSS) space station rack and its Distillation Assembly (DA) subsystem using EAI's human modeling simulation software, Jack. When installed on the International Space Station (ISS), ECLSS will provide the life and environment support needed to adequately sustain crew life. The DA is an Orbital Replaceable Unit (ORU) that provides means of wastewater (primarily urine from flight crew and experimental animals) reclamation. Jack was used to create a model of the weightless environment of the ISS Node 3, where the ECLSS is housed. Computer aided drawings of the ECLSS rack and DA system were also brought into the environment. Anthropometric models of a 95th percentile male and 5th percentile female were used to examine the human interfaces encountered during various ECLSS and DA tasks. The results of the task analyses were used in suggesting modifications to hardware and crew task procedures to improve accessibility, conserve crew time, and add convenience for the crew. This paper will address some of those suggested modifications and the method of presenting final analyses for requirements verification.

Developing a Model Component

NASA Technical Reports Server (NTRS)

Fields, Christina M.

2013-01-01

The Spaceport Command and Control System (SCCS) Simulation Computer Software Configuration Item (CSCI) is,. responsible for providing simulations to support test and verification of SCCS hardware and software. The Universal Coolant Transporter System (UCTS) is a Space Shuttle Orbiter support piece of the Ground Servicing Equipment (GSE). The purpose of the UCTS is to provide two support services to the Space Shuttle Orbiter immediately after landing at the Shuttle Landing Facility. The Simulation uses GSE Models to stand in for the actual systems to support testing of SCCS systems s:luring their development. As an intern at KSC, my assignment was to develop a model component for the UCTS. I was given a fluid component (drier) to model in Matlab. The drier was a Catch All replaceable core type filter-drier. The filter-drier provides maximum protection for the thermostatic expansion valve and solenoid valve from dirt that may be in the system. The filter-drier also protects the valves from freezing up. I researched fluid dynamics to understand the function of my component. I completed training for UNIX and Simulink to help aid in my assignment. The filter-drier was modeled by determining affects it has on the pressure, velocity and temperature of the system. I used Bernoulli's Equation to calculate the pressure and velocity differential through the dryer. I created my model filter-drier in Simulink and wrote the test script to test the component. I completed component testing and captured test data. The finalized model was sent for peer review for any improvements.

Validation of a "Kane's Dynamics" Model for the Active Rack Isolation System

NASA Technical Reports Server (NTRS)

Beech, Geoffrey S.; Hampton, R. David

2000-01-01

Many microgravity space-science experiments require vibratory acceleration levels unachievable without active isolation. The Boeing Corporation's Active Rack Isolation System (ARIS) employs a novel combination of magnetic actuation and mechanical linkages, to address these isolation requirements on the International Space Station (ISS). ARIS provides isolation at the rack (international Standard Payload Rack, or ISPR) level. Effective model-based vibration isolation requires (1) an isolation device, (2) an adequate dynamic (i.e., mathematical) model of that isolator, and (3) a suitable, corresponding controller, ARIS provides the ISS response to the first requirement. In November 1999, the authors presented a response to the second ("A 'Kane's Dynamics' model for the Active Rack Isolation System", Hampton and Beech) intended to facilitate an optimal-controls approach to the third. This paper documents the validation of that high-fidelity dynamic model of ARIS. As before, this model contains the full actuator dynamics, however, the umbilical models are not included in this presentation. The validation of this dynamics model was achieved by utilizing two Commercial Off the Shelf (COTS) software tools: Deneb's ENVISION, and Online Dynamics' AUTOLEV. ENVISION is a robotics software package developed for the automotive industry that employs 3-dimensional (3-D) Computer Aided Design (CAD) models to facilitate both forward and inverse kinematics analyses. AUTOLEV is a DOS based interpreter that is designed in general to solve vector based mathematical problems and specifically to solve Dynamics problems using Kane's method.

More Than A SketchUp

NASA Technical Reports Server (NTRS)

Davis, Derrick D.

2014-01-01

This 2014 summer internship assignment at John F. Kennedy Space Center (K.S.C) was conducted with the National Aeronautics and Space Administration (NASA) Engineering and Technology (NE) group in support of the Control and Data Systems Division (NE-C) within the Test, Operations & Support Software Engineering Branch (NE-C2). The primary focus of this project was to assist Branch Chief Laurie B. Griffin, to support NASA's Small Payload Launch Integrated Testing Services (SPLITS) mission, by mastering the capabilities of 3-D modeling software called SketchUp. I used SketchUp to create a virtual environment for different laboratories of the NE-00 Division. My mission was to have these models uploaded into a K.S.C Partnerships Website and be used as a visual aid to viewers who browsed the site. The leads of this project were Kay L. Craig, Business and Industry Specialist (AD-A) and Steven E. Cain, (FA-C). I teamed with fellow intern Tait Sorenson of the Flight Structures and Thermal Protection Systems Branch (NE-M5) and met with many K.S.C lab managers willing to display their lab's structure and capabilities. The information collected during these lab tours was vital to the building of the K.S.C Partnerships Website. To accomplish this goal Sorenson and I later teamed with fellow Marketing intern Marlee Pereda-Ramos, of the Spaceport Planning Office In Center Planning And Development (AD-A) Along with Ramos, Tait and I toured an array of laboratories and got first hand exposure to their functions and capabilities.

GIDEP Batching Tool

NASA Technical Reports Server (NTRS)

Fong, Danny; Odell,Dorice; Barry, Peter; Abrahamian, Tomik

2008-01-01

This software provides internal, automated search mechanics of GIDEP (Government- Industry Data Exchange Program) Alert data imported from the GIDEP government Web site. The batching tool allows the import of a single parts list in tab-delimited text format into the local JPL GIDEP database. Delimiters from every part number are removed. The original part numbers with delimiters are compared, as well as the newly generated list without the delimiters. The two lists run against the GIDEP imports, and output any matches. This feature only works with Netscape 2.0 or greater, or Internet Explorer 4.0 or greater. The user selects the browser button to choose a text file to import. When the submit button is pressed, this script will import alerts from the text file into the local JPL GIDEP database. This batch tool provides complete in-house control over exported material and data for automated batch match abilities. The batching tool has the ability to match capabilities of the parts list to tables, and yields results that aid further research and analysis. This provides more control over GIDEP information for metrics and reports information not provided by the government site. This software yields results quickly and gives more control over external data from the government site in order to generate other reports not available from the external source. There is enough space to store years of data. The program relates to risk identification and management with regard to projects and GIDEP alert information encompassing flight parts for space exploration.

Space station software reliability analysis based on failures observed during testing at the multisystem integration facility

NASA Technical Reports Server (NTRS)

Tamayo, Tak Chai

1987-01-01

Quality of software not only is vital to the successful operation of the space station, it is also an important factor in establishing testing requirements, time needed for software verification and integration as well as launching schedules for the space station. Defense of management decisions can be greatly strengthened by combining engineering judgments with statistical analysis. Unlike hardware, software has the characteristics of no wearout and costly redundancies, thus making traditional statistical analysis not suitable in evaluating reliability of software. A statistical model was developed to provide a representation of the number as well as types of failures occur during software testing and verification. From this model, quantitative measure of software reliability based on failure history during testing are derived. Criteria to terminate testing based on reliability objectives and methods to estimate the expected number of fixings required are also presented.

Flight Planning Branch NASA Co-op Tour

NASA Technical Reports Server (NTRS)

Marr, Aja M.

2013-01-01

This semester I worked with the Flight Planning Branch at the NASA Johnson Space Center. I learned about the different aspects of flight planning for the International Space Station as well as the software that is used internally and ISSLive! which is used to help educate the public on the space program. I had the opportunity to do on the job training in the Mission Control Center with the planning team. I transferred old timeline records from the planning team's old software to the new software in order to preserve the data for the future when the software is retired. I learned about the operations of the International Space Station, the importance of good communication between the different parts of the planning team, and enrolled in professional development classes as well as technical classes to learn about the space station.

Software development: A paradigm for the future

NASA Technical Reports Server (NTRS)

Basili, Victor R.

1989-01-01

A new paradigm for software development that treats software development as an experimental activity is presented. It provides built-in mechanisms for learning how to develop software better and reusing previous experience in the forms of knowledge, processes, and products. It uses models and measures to aid in the tasks of characterization, evaluation and motivation. An organization scheme is proposed for separating the project-specific focus from the organization's learning and reuse focuses of software development. The implications of this approach for corporations, research and education are discussed and some research activities currently underway at the University of Maryland that support this approach are presented.

Standalone medical device software: The evolving regulatory framework.

PubMed

McCarthy, Avril D; Lawford, Patricia V

2014-01-01

The paper provides an introduction to the regulatory landscape affecting a particular category of medical technology, namely standalone software-sometimes referred to as 'software as a medical device'. To aid the reader's comprehension of an often complex area, six case studies are outlined and discussed before the paper continues to provide detail of how software with a medical purpose in its own right can potentially be classified as a medical device. The reader is provided an appreciation of how to go about classifying such software and references to support the developer new to the field in locating detailed regulatory support documents and contact points for advice.

Software support environment design knowledge capture

NASA Technical Reports Server (NTRS)

Dollman, Tom

1990-01-01

The objective of this task is to assess the potential for using the software support environment (SSE) workstations and associated software for design knowledge capture (DKC) tasks. This assessment will include the identification of required capabilities for DKC and hardware/software modifications needed to support DKC. Several approaches to achieving this objective are discussed and interim results are provided: (1) research into the problem of knowledge engineering in a traditional computer-aided software engineering (CASE) environment, like the SSE; (2) research into the problem of applying SSE CASE tools to develop knowledge based systems; and (3) direct utilization of SSE workstations to support a DKC activity.

A Software Engineering Approach based on WebML and BPMN to the Mediation Scenario of the SWS Challenge

NASA Astrophysics Data System (ADS)

Brambilla, Marco; Ceri, Stefano; Valle, Emanuele Della; Facca, Federico M.; Tziviskou, Christina

Although Semantic Web Services are expected to produce a revolution in the development of Web-based systems, very few enterprise-wide design experiences are available; one of the main reasons is the lack of sound Software Engineering methods and tools for the deployment of Semantic Web applications. In this chapter, we present an approach to software development for the Semantic Web based on classical Software Engineering methods (i.e., formal business process development, computer-aided and component-based software design, and automatic code generation) and on semantic methods and tools (i.e., ontology engineering, semantic service annotation and discovery).

The genesis of the AIDS policy and AIDS Space in Brazil (1981-1989)

PubMed Central

de Barros, Sandra Garrido; Vieira-da-Silva, Ligia Maria

2016-01-01

ABSTRACT OBJECTIVE To analyze the genesis of the policy for controlling AIDS in Brazil. METHODS Socio-historical study (1981-1989), based on Bordieu’s genetic sociology, by document analysis, bibliographical review, and in-depth interviews. It consisted of a connection between the analysis of the paths of 33 agents involved in the creation of a social space focusing on AIDS-related issues and the historical possibility conditions of the drafting of a specific policy. RESULTS AIDS Space is a gathering point for the paths of agents from several social fields (medical, scientific, political, and bureaucratic fields). A specific space for relationships, which enabled the drafting of a policy for controlling the AIDS epidemic, but also a place where the authority to talk about the meaning of the disease, the methods to prevent and treat it was under dispute. The analysis showed how the various structures (democratic administrations in Sao Paulo and at the national level, with public health officers taking important positions) and the lack of a specific therapy contributed to social agents of different ranks and backgrounds to initially set prevention as a priority. CONCLUSIONS The rise of the sanitary movement, the organization of SUS, and the dominance of the medical field at the AIDS Space contributed to foster treatment as a part of the measures to control the epidemic. These conditions allowed drafting a policy based on the integrality of care, by linking prevention and treatment in the following decade, with important participation from state bureaucracy and researchers. PMID:27463255

Integrated Power, Avionics, and Software (iPAS) Space Telecommunications Radio System (STRS) Radio User's Guide -- Advanced Exploration Systems (AES)

NASA Technical Reports Server (NTRS)

Roche, Rigoberto; Shalkhauser, Mary Jo Windmille

2017-01-01

The Integrated Power, Avionics and Software (IPAS) software defined radio (SDR) was implemented on the Reconfigurable, Intelligently-Adaptive Communication System (RAICS) platform, for radio development at NASA Johnson Space Center. Software and hardware description language (HDL) code were delivered by NASA Glenn Research Center for use in the IPAS test bed and for development of their own Space Telecommunications Radio System (STRS) waveforms on the RAICS platform. The purpose of this document is to describe how to setup and operate the IPAS STRS Radio platform with its delivered test waveform.

Perspectives on NASA flight software development - Apollo, Shuttle, Space Station

NASA Technical Reports Server (NTRS)

Garman, John R.

1990-01-01

Flight data systems' software development is chronicled for the period encompassing NASA's Apollo, Space Shuttle, and (ongoing) Space Station Freedom programs, with attention to the methodologies and 'development tools' employed in each case and their mutual relationships. A dominant concern in all three programs has been the accommodation of software change; it has also been noted that any such long-term program carries the additional challenge of identifying which elements of its software-related 'institutional memory' are most critical, in order to preclude their loss through the retirement, promotion, or transfer of its 'last expert'.

Software Performs Complex Design Analysis

NASA Technical Reports Server (NTRS)

2008-01-01

Designers use computational fluid dynamics (CFD) to gain greater understanding of the fluid flow phenomena involved in components being designed. They also use finite element analysis (FEA) as a tool to help gain greater understanding of the structural response of components to loads, stresses and strains, and the prediction of failure modes. Automated CFD and FEA engineering design has centered on shape optimization, which has been hindered by two major problems: 1) inadequate shape parameterization algorithms, and 2) inadequate algorithms for CFD and FEA grid modification. Working with software engineers at Stennis Space Center, a NASA commercial partner, Optimal Solutions Software LLC, was able to utilize its revolutionary, one-of-a-kind arbitrary shape deformation (ASD) capability-a major advancement in solving these two aforementioned problems-to optimize the shapes of complex pipe components that transport highly sensitive fluids. The ASD technology solves the problem of inadequate shape parameterization algorithms by allowing the CFD designers to freely create their own shape parameters, therefore eliminating the restriction of only being able to use the computer-aided design (CAD) parameters. The problem of inadequate algorithms for CFD grid modification is solved by the fact that the new software performs a smooth volumetric deformation. This eliminates the extremely costly process of having to remesh the grid for every shape change desired. The program can perform a design change in a markedly reduced amount of time, a process that would traditionally involve the designer returning to the CAD model to reshape and then remesh the shapes, something that has been known to take hours, days-even weeks or months-depending upon the size of the model.

Software for Dosage Individualization of Voriconazole for Immunocompromised Patients

PubMed Central

VanGuilder, Michael; Donnelly, J. Peter; Blijlevens, Nicole M. A.; Brüggemann, Roger J. M.; Jelliffe, Roger W.; Neely, Michael N.

2013-01-01

The efficacy of voriconazole is potentially compromised by considerable pharmacokinetic variability. There are increasing insights into voriconazole concentrations that are safe and effective for treatment of invasive fungal infections. Therapeutic drug monitoring is increasingly advocated. Software to aid in the individualization of dosing would be an extremely useful clinical tool. We developed software to enable the individualization of voriconazole dosing to attain predefined serum concentration targets. The process of individualized voriconazole therapy was based on concepts of Bayesian stochastic adaptive control. Multiple-model dosage design with feedback control was used to calculate dosages that achieved desired concentration targets with maximum precision. The performance of the software program was assessed using the data from 10 recipients of an allogeneic hematopoietic stem cell transplant (HSCT) receiving intravenous (i.v.) voriconazole. The program was able to model the plasma concentrations with a high level of precision, despite the wide range of concentration trajectories and interindividual pharmacokinetic variability. The voriconazole concentrations predicted after the last dosages were largely concordant with those actually measured. Simulations provided an illustration of the way in which the software can be used to adjust dosages of patients falling outside desired concentration targets. This software appears to be an extremely useful tool to further optimize voriconazole therapy and aid in therapeutic drug monitoring. Further prospective studies are now required to define the utility of the controller in daily clinical practice. PMID:23380734

Geometric modeling for computer aided design

NASA Technical Reports Server (NTRS)

Schwing, James L.; Olariu, Stephen

1995-01-01

The primary goal of this grant has been the design and implementation of software to be used in the conceptual design of aerospace vehicles particularly focused on the elements of geometric design, graphical user interfaces, and the interaction of the multitude of software typically used in this engineering environment. This has resulted in the development of several analysis packages and design studies. These include two major software systems currently used in the conceptual level design of aerospace vehicles. These tools are SMART, the Solid Modeling Aerospace Research Tool, and EASIE, the Environment for Software Integration and Execution. Additional software tools were designed and implemented to address the needs of the engineer working in the conceptual design environment. SMART provides conceptual designers with a rapid prototyping capability and several engineering analysis capabilities. In addition, SMART has a carefully engineered user interface that makes it easy to learn and use. Finally, a number of specialty characteristics have been built into SMART which allow it to be used efficiently as a front end geometry processor for other analysis packages. EASIE provides a set of interactive utilities that simplify the task of building and executing computer aided design systems consisting of diverse, stand-alone, analysis codes. Resulting in a streamlining of the exchange of data between programs reducing errors and improving the efficiency. EASIE provides both a methodology and a collection of software tools to ease the task of coordinating engineering design and analysis codes.

Virtual Reality-Based Technologies in Dental Medicine: Knowledge, Attitudes and Practice among Students and Practitioners

ERIC Educational Resources Information Center

Sabalic, Maja; Schoener, Jason D.

2017-01-01

Virtual reality-based technologies have been used in dentistry for almost two decades. Dental simulators, planning software and CAD/CAM (computer-aided design/computer-aided manufacturing) systems have significantly developed over the years and changed both dental education and clinical practice. This study aimed to assess the knowledge, attitudes…

Factors Associated with Incomplete Reporting of HIV and AIDS by Uganda's Surveillance System

ERIC Educational Resources Information Center

Akankunda, Denis B.

2014-01-01

Background: Over the last 20 years, Uganda has piloted and implemented various management information systems (MIS) for better surveillance of HIV/AIDS. With support from the United States Government, Uganda introduced the District Health Information Software 2 (DHIS2) in 2012. However, districts have yet to fully adapt to this system given a…

Computer Aided Drafting Packages for Secondary Education. Edition 1. Apple II and Macintosh. A MicroSIFT Quarterly Report.

ERIC Educational Resources Information Center

Pollard, Jim

This report reviews software packages for Apple Macintosh and Apple II computers available to secondary schools to teach computer-aided drafting (CAD). Products for the report were gathered through reviews of CAD periodicals, computers in education periodicals, advertisements, and teacher recommendations. The first section lists the primary…

Functional Specifications for Computer Aided Training Systems Development and Management (CATSDM) Support Functions. Final Report.

ERIC Educational Resources Information Center

Hughes, John; And Others

This report provides a description of a Computer Aided Training System Development and Management (CATSDM) environment based on state-of-the-art hardware and software technology, and including recommendations for off the shelf systems to be utilized as a starting point in addressing the particular systematic training and instruction design and…

The Effectiveness of a Single Intervention of Computer-Aided Argument Mapping in a Marketing and a Financial Accounting Subject

ERIC Educational Resources Information Center

Carrington, Michal; Chen, Richard; Davies, Martin; Kaur, Jagjit; Neville, Benjamin

2011-01-01

An argument map visually represents the structure of an argument, outlining its informal logical connections and informing judgments as to its worthiness. Argument mapping can be augmented with dedicated software that aids the mapping process. Empirical evidence suggests that semester-length subjects using argument mapping along with dedicated…

PEO Integration Acronym Book

DTIC Science & Technology

2011-02-01

Command CASE Computer Aided Software Engineering CASEVAC Casualty Evacuation CASTFOREM Combined Arms And Support Task Force Evaluation Model CAT Center For...Advanced Technologies CAT Civil Affairs Team CAT Combined Arms Training CAT Crew Integration CAT Crisis Action Team CATIA Computer-Aided Three...Dimensional Interactive Application CATOX Catalytic Oxidation CATS Combined Arms Training Strategy CATT Combined Arms Tactical Trainer CATT Computer

[Veneer computer aided design based on reverse engineering technology].

PubMed

Liu, Ming-li; Chen, Xiao-dong; Wang, Yong

2012-03-01

To explore the computer aided design (CAD) method of veneer restoration, and to assess if the solution can help prosthesis meet morphology esthetics standard. A volunteer's upper right central incisor needed to be restored with veneer. Super hard stone models of patient's dentition (before and after tooth preparation) were scanned with the three-dimensional laser scanner. The veneer margin was designed as butt-to-butt type. The veneer was constructed using reverse engineering (RE) software. The technique guideline of veneers CAD was explore based on RE software, and the veneers was smooth, continuous and symmetrical, which met esthetics construction needs. It was a feasible method to reconstruct veneer restoration based on RE technology.

Software Modules for the Proximity-1 Space Link Interleaved Time Synchronization (PITS) Protocol

NASA Technical Reports Server (NTRS)

Woo, Simon S.; Veregge, John R.; Gao, Jay L.; Clare, Loren P.; Mills, David

2012-01-01

The Proximity-1 Space Link Interleaved Time Synchronization (PITS) protocol provides time distribution and synchronization services for space systems. A software prototype implementation of the PITS algorithm has been developed that also provides the test harness to evaluate the key functionalities of PITS with simulated data source and sink. PITS integrates time synchronization functionality into the link layer of the CCSDS Proximity-1 Space Link Protocol. The software prototype implements the network packet format, data structures, and transmit- and receive-timestamp function for a time server and a client. The software also simulates the transmit and receive-time stamp exchanges via UDP (User Datagram Protocol) socket between a time server and a time client, and produces relative time offsets and delay estimates.

ARC-2007-ACD07-0140-002

NASA Image and Video Library

2007-07-31

David L. Iverson of NASA Ames Research Center, Moffett Field, California (in foreground) led development of computer software to monitor the conditions of the gyroscopes that keep the International Space Station (ISS) properly oriented in space as the ISS orbits Earth. Also, Charles Lee is pictured. During its develoment, researchers used the software to analyze archived gyroscope records. In these tests, users noticed problems with the gyroscopes long before the current systems flagged glitches. Testers trained using several months of normal space station gyroscope data collected by the International Space Station Mission Control Center at NASA Johnson Space Center, Houston. Promising tests results convinced officials to start using the software in 2007.

Computer-Aided Modeling and Analysis of Power Processing Systems (CAMAPPS), phase 1

NASA Technical Reports Server (NTRS)

Kim, S.; Lee, J.; Cho, B. H.; Lee, F. C.

1986-01-01

The large-signal behaviors of a regulator depend largely on the type of power circuit topology and control. Thus, for maximum flexibility, it is best to develop models for each functional block a independent modules. A regulator can then be configured by collecting appropriate pre-defined modules for each functional block. In order to complete the component model generation for a comprehensive spacecraft power system, the following modules were developed: solar array switching unit and control; shunt regulators; and battery discharger. The capability of each module is demonstrated using a simplified Direct Energy Transfer (DET) system. Large-signal behaviors of solar array power systems were analyzed. Stability of the solar array system operating points with a nonlinear load is analyzed. The state-plane analysis illustrates trajectories of the system operating point under various conditions. Stability and transient responses of the system operating near the solar array's maximum power point are also analyzed. The solar array system mode of operation is described using the DET spacecraft power system. The DET system is simulated for various operating conditions. Transfer of the software program CAMAPPS (Computer Aided Modeling and Analysis of Power Processing Systems) to NASA/GSFC (Goddard Space Flight Center) was accomplished.

Space Telecommunications Radio System (STRS) Architecture Standard. Release 1.02.1

NASA Technical Reports Server (NTRS)

Reinhart, Richard C.; Kacpura, Thomas J.; Handler, Louis M.; Hall, C. Steve; Mortensen, Dale J.; Johnson, Sandra K.; Briones, Janette C.; Nappier, Jennifer M.; Downey, Joseph A.; Lux, James P.

2012-01-01

This document contains the NASA architecture standard for software defined radios used in space- and ground-based platforms to enable commonality among radio developments to enhance capability and services while reducing mission and programmatic risk. Transceivers (or transponders) with functionality primarily defined in software (e.g., firmware) have the ability to change their functional behavior through software alone. This radio architecture standard offers value by employing common waveform software interfaces, method of instantiation, operation, and testing among different compliant hardware and software products. These common interfaces within the architecture abstract application software from the underlying hardware to enable technology insertion independently at either the software or hardware layer.

Deep space network software cost estimation model

NASA Technical Reports Server (NTRS)

Tausworthe, R. C.

1981-01-01

A parametric software cost estimation model prepared for Jet PRopulsion Laboratory (JPL) Deep Space Network (DSN) Data System implementation tasks is described. The resource estimation mdel modifies and combines a number of existing models. The model calibrates the task magnitude and difficulty, development environment, and software technology effects through prompted responses to a set of approximately 50 questions. Parameters in the model are adjusted to fit JPL software life-cycle statistics.

Safe Software for Space Applications: Building on the DO-178 Experience

NASA Astrophysics Data System (ADS)

Dorsey, Cheryl A.; Dorsey, Timothy A.

2013-09-01

DO-178, Software Considerations in Airborne Systems and Equipment Certification, is the well-known international standard dealing with the assurance of software used in airborne systems [1,2]. Insights into the DO-178 experiences, strengths and weaknesses can benefit the international space community. As DO-178 is an excellent standard for safe software development when used appropriately, this paper provides lessons learned and suggestions for using it effectively.

Implications of Responsive Space on the Flight Software Architecture

NASA Technical Reports Server (NTRS)

Wilmot, Jonathan

2006-01-01

The Responsive Space initiative has several implications for flight software that need to be addressed not only within the run-time element, but the development infrastructure and software life-cycle process elements as well. The runtime element must at a minimum support Plug & Play, while the development and process elements need to incorporate methods to quickly generate the needed documentation, code, tests, and all of the artifacts required of flight quality software. Very rapid response times go even further, and imply little or no new software development, requiring instead, using only predeveloped and certified software modules that can be integrated and tested through automated methods. These elements have typically been addressed individually with significant benefits, but it is when they are combined that they can have the greatest impact to Responsive Space. The Flight Software Branch at NASA's Goddard Space Flight Center has been developing the runtime, infrastructure and process elements needed for rapid integration with the Core Flight software System (CFS) architecture. The CFS architecture consists of three main components; the core Flight Executive (cFE), the component catalog, and the Integrated Development Environment (DE). This paper will discuss the design of the components, how they facilitate rapid integration, and lessons learned as the architecture is utilized for an upcoming spacecraft.

Independent verification and validation for Space Shuttle flight software

NASA Technical Reports Server (NTRS)

1992-01-01

The Committee for Review of Oversight Mechanisms for Space Shuttle Software was asked by the National Aeronautics and Space Administration's (NASA) Office of Space Flight to determine the need to continue independent verification and validation (IV&V) for Space Shuttle flight software. The Committee found that the current IV&V process is necessary to maintain NASA's stringent safety and quality requirements for man-rated vehicles. Therefore, the Committee does not support NASA's plan to eliminate funding for the IV&V effort in fiscal year 1993. The Committee believes that the Space Shuttle software development process is not adequate without IV&V and that elimination of IV&V as currently practiced will adversely affect the overall quality and safety of the software, both now and in the future. Furthermore, the Committee was told that no organization within NASA has the expertise or the manpower to replace the current IV&V function in a timely fashion, nor will building this expertise elsewhere necessarily reduce cost. Thus, the Committee does not recommend moving IV&V functions to other organizations within NASA unless the current IV&V is maintained for as long as it takes to build comparable expertise in the replacing organization.

Volumetric Analysis of Alveolar Bone Defect Using Three-Dimensional-Printed Models Versus Computer-Aided Engineering.

PubMed

Du, Fengzhou; Li, Binghang; Yin, Ningbei; Cao, Yilin; Wang, Yongqian

2017-03-01

Knowing the volume of a graft is essential in repairing alveolar bone defects. This study investigates the 2 advanced preoperative volume measurement methods: three-dimensional (3D) printing and computer-aided engineering (CAE). Ten unilateral alveolar cleft patients were enrolled in this study. Their computed tomographic data were sent to 3D printing and CAE software. A simulated graft was used on the 3D-printed model, and the graft volume was measured by water displacement. The volume calculated by CAE software used mirror-reverses technique. The authors compared the actual volumes of the simulated grafts with the CAE software-derived volumes. The average volume of the simulated bone grafts by 3D-printed models was 1.52 mL, higher than the mean volume of 1.47 calculated by CAE software. The difference between the 2 volumes was from -0.18 to 0.42 mL. The paired Student t test showed no statistically significant difference between the volumes derived from the 2 methods. This study demonstrated that the mirror-reversed technique by CAE software is as accurate as the simulated operation on 3D-printed models in unilateral alveolar cleft patients. These findings further validate the use of 3D printing and CAE technique in alveolar defect repairing.

Design and Empirical Evaluation of Search Software for Legal Professionals on the WWW.

ERIC Educational Resources Information Center

Dempsey, Bert J.; Vreeland, Robert C.; Sumner, Robert G., Jr.; Yang, Kiduk

2000-01-01

Discussion of effective search aids for legal researchers on the World Wide Web focuses on the design and evaluation of two software systems developed to explore models for browsing and searching across a user-selected set of Web sites. Describes crawler-enhanced search engines, filters, distributed full-text searching, and natural language…

Toward More Critical Reviewing and Analysis of CD-ROM User Software Interfaces.

ERIC Educational Resources Information Center

Zink, Steven D.

1991-01-01

Criticizes reviews of library CD-ROM products as being uncritical of the user interface and advocates a more rigorous evaluation, not only to aid potential buyers, but as a way to influence manufacturers. Congressional Information Services' Masterfile 2 is evaluated in the context of Heckel's "Principles of Friendly Software Design." (24…

Rapid Software-Based Design and Optical Transient Liquid Molding of Microparticles.

PubMed

Wu, Chueh-Yu; Owsley, Keegan; Di Carlo, Dino

2015-12-22

Microparticles with complex 3D shape and composition are produced using a novel fabrication method, optical transient liquid molding, in which a 2D light pattern exposes a photopolymer precursor stream shaped along the flow axis by software-aided inertial flow engineering. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

EduSpeak[R]: A Speech Recognition and Pronunciation Scoring Toolkit for Computer-Aided Language Learning Applications

ERIC Educational Resources Information Center

Franco, Horacio; Bratt, Harry; Rossier, Romain; Rao Gadde, Venkata; Shriberg, Elizabeth; Abrash, Victor; Precoda, Kristin

2010-01-01

SRI International's EduSpeak[R] system is a software development toolkit that enables developers of interactive language education software to use state-of-the-art speech recognition and pronunciation scoring technology. Automatic pronunciation scoring allows the computer to provide feedback on the overall quality of pronunciation and to point to…

Computer Program Re-layers Engineering Drawings

NASA Technical Reports Server (NTRS)

Crosby, Dewey C., III

1990-01-01

RULCHK computer program aids in structuring layers of information pertaining to part or assembly designed with software described in article "Software for Drawing Design Details Concurrently" (MFS-28444). Checks and optionally updates structure of layers for part. Enables designer to construct model and annotate its documentation without burden of manually layering part to conform to standards at design time.

Collaboration Between NASA Centers of Excellence on Autonomous System Software Development

NASA Technical Reports Server (NTRS)

Goodrich, Charles H.; Larson, William E.; Delgado, H. (Technical Monitor)

2001-01-01

Software for space systems flight operations has its roots in the early days of the space program when computer systems were incapable of supporting highly complex and flexible control logic. Control systems relied on fast data acquisition and supervisory control from a roomful of systems engineers on the ground. Even though computer hardware and software has become many orders of magnitude more capable, space systems have largely adhered to this original paradigm In an effort to break this mold, Kennedy Space Center (KSC) has invested in the development of model-based diagnosis and control applications for ten years having broad experience in both ground and spacecraft systems and software. KSC has now partnered with Ames Research Center (ARC), NASA's Center of Excellence in Information Technology, to create a new paradigm for the control of dynamic space systems. ARC has developed model-based diagnosis and intelligent planning software that enables spacecraft to handle most routine problems automatically and allocate resources in a flexible way to realize mission objectives. ARC demonstrated the utility of onboard diagnosis and planning with an experiment aboard Deep Space I in 1999. This paper highlights the software control system collaboration between KSC and ARC. KSC has developed a Mars In-situ Resource Utilization testbed based on the Reverse Water Gas Shift (RWGS) reaction. This plant, built in KSC's Applied Chemistry Laboratory, is capable of producing the large amount of Oxygen that would be needed to support a Human Mars Mission. KSC and ARC are cooperating to develop an autonomous, fault-tolerant control system for RWGS to meet the need for autonomy on deep space missions. The paper will also describe how the new system software paradigm will be applied to Vehicle Health Monitoring, tested on the new X vehicles and integrated into future launch processing systems.

The TAVERNS emulator: An Ada simulation of the space station data communications network and software development environment

NASA Technical Reports Server (NTRS)

Howes, Norman R.

1986-01-01

The Space Station DMS (Data Management System) is the onboard component of the Space Station Information System (SSIS) that includes the computers, networks and software that support the various core and payload subsystems of the Space Station. TAVERNS (Test And Validation Environment for Remote Networked Systems) is a distributed approach for development and validation of application software for Space Station. The TAVERNS concept assumes that the different subsystems will be developed by different contractors who may be geographically separated. The TAVERNS Emulator is an Ada simulation of a TAVERNS on the ASD VAX. The software services described in the DMS Test Bed User's Manual are being emulated on the VAX together with simulations of some of the core subsystems and a simulation of the DCN. The TAVERNS Emulator will be accessible remotely from any VAX that can communicate with the ASD VAX.

Information Systems for NASA's Aeronautics and Space Enterprises

NASA Technical Reports Server (NTRS)

Kutler, Paul

1998-01-01

The aerospace industry is being challenged to reduce costs and development time as well as utilize new technologies to improve product performance. Information technology (IT) is the key to providing revolutionary solutions to the challenges posed by the increasing complexity of NASA's aeronautics and space missions and the sophisticated nature of the systems that enable them. The NASA Ames vision is to develop technologies enabling the information age, expanding the frontiers of knowledge for aeronautics and space, improving America's competitive position, and inspiring future generations. Ames' missions to accomplish that vision include: 1) performing research to support the American aviation community through the unique integration of computation, experimentation, simulation and flight testing, 2) studying the health of our planet, understanding living systems in space and the origins of the universe, developing technologies for space flight, and 3) to research, develop and deliver information technologies and applications. Information technology may be defined as the use of advance computing systems to generate data, analyze data, transform data into knowledge and to use as an aid in the decision-making process. The knowledge from transformed data can be displayed in visual, virtual and multimedia environments. The decision-making process can be fully autonomous or aided by a cognitive processes, i.e., computational aids designed to leverage human capacities. IT Systems can learn as they go, developing the capability to make decisions or aid the decision making process on the basis of experiences gained using limited data inputs. In the future, information systems will be used to aid space mission synthesis, virtual aerospace system design, aid damaged aircraft during landing, perform robotic surgery, and monitor the health and status of spacecraft and planetary probes. NASA Ames through the Center of Excellence for Information Technology Office is leading the effort in pursuit of revolutionary, IT-based approaches to satisfying NASA's aeronautics and space requirements. The objective of the effort is to incorporate information technologies within each of the Agency's four Enterprises, i.e., Aeronautics and Space Transportation Technology, Earth, Science, Human Exploration and Development of Space and Space Sciences. The end results of these efforts for Enterprise programs and projects should be reduced cost, enhanced mission capability and expedited mission completion.

Spacelab software development and integration concepts study report, volume 1

NASA Technical Reports Server (NTRS)

Rose, P. L.; Willis, B. G.

1973-01-01

The proposed software guidelines to be followed by the European Space Research Organization in the development of software for the Spacelab being developed for use as a payload for the space shuttle are documented. Concepts, techniques, and tools needed to assure the success of a programming project are defined as they relate to operation of the data management subsystem, support of experiments and space applications, use with ground support equipment, and for integration testing.

A History of Space Shuttle Main Engine (SSME) Redline Limits Management

NASA Technical Reports Server (NTRS)

Arnold, Thomas M.

2011-01-01

The Space Shuttle Main Engine (SSME) has several "redlines", which are operational limits designated to preclude a catastrophic shutdown of the SSME. The Space Shuttle Orbiter utilizes a combination of hardware and software to enable or disable the automated redline shutdown capability. The Space Shuttle is launched with the automated SSME redline limits enabled, but there are many scenarios which may result in the manual disabling of the software by the onboard crew. The operational philosophy for manually enabling and disabling the redline limits software has evolved continuously throughout the history of the Space Shuttle Program, due to events such as SSME hardware changes and updates to Space Shuttle contingency abort software. In this paper, the evolution of SSME redline limits management will be fully reviewed, including the operational scenarios which call for manual intervention, and the events that triggered changes to the philosophy. Following this review, improvements to the management of redline limits for future spacecraft will be proposed.

Holodeck: Telepresence Dome Visualization System Simulations

NASA Technical Reports Server (NTRS)

Hite, Nicolas

2012-01-01

This paper explores the simulation and consideration of different image-projection strategies for the Holodeck, a dome that will be used for highly immersive telepresence operations in future endeavors of the National Aeronautics and Space Administration (NASA). Its visualization system will include a full 360 degree projection onto the dome's interior walls in order to display video streams from both simulations and recorded video. Because humans innately trust their vision to precisely report their surroundings, the Holodeck's visualization system is crucial to its realism. This system will be rigged with an integrated hardware and software infrastructure-namely, a system of projectors that will relay with a Graphics Processing Unit (GPU) and computer to both project images onto the dome and correct warping in those projections in real-time. Using both Computer-Aided Design (CAD) and ray-tracing software, virtual models of various dome/projector geometries were created and simulated via tracking and analysis of virtual light sources, leading to the selection of two possible configurations for installation. Research into image warping and the generation of dome-ready video content was also conducted, including generation of fisheye images, distortion correction, and the generation of a reliable content-generation pipeline.

Help: first aid issues.

PubMed

Granitoff, N; Whitaker, I Y; Diccini, S; Goncalves, V C; Marin, H F

1995-01-01

First aid is the initial and immediate care given to a victim outside the hospital environment, with the purpose of assuring life and avoiding worsening conditions until he/she receives qualified assistance. Providing immediate aid to someone requires tranquility and, above all, knowledge on what has to be done or not in each situation. In addition to being treated by health professionals, the chances that a victim will receive early treatment by others are large. However, in Brazil, access to information, and the possibility of reviewing it whenever necessary, may contribute greatly to the process of assimilation of this knowledge, in addition to exercises on simulated cases. Informatics has been shown as an extremely useful tool in the development of educational software, considering its multiplicity of resources and providing for the users: motivation for an interactive experience, an individualized teaching that takes into account his/her own rhythm and desired complexity level, besides making possible the user's capacity for solving problems through simulated situations. Considering that, the number of individuals of the population prepared to act as First Aid helpers in situations of life threatening accidents or sudden illness is still very scarce. The ever increasing use of the computer as a mean of spreading information in schools, enterprises, and even households and considering the advantages of an educational software for the users regarding storage and retrieval of information when needed, we proposed the creation of an interactive teaching software. This software is being developed using Storyboard live. The methodology is the following: literature review, selection of images, development of the program, application tests. The initial selected issues are: assessment of the victim, cardiorespiratory arrest and resuscitation, airway obstruction, wounds, and hemorrhages. After utilizing the program, the user should be able to solve hypothetical situations with minimal initial care and maximal physical comfort for an accident or sudden illness victim.

Virtual acoustic environments for comprehensive evaluation of model-based hearing devices.

PubMed

Grimm, Giso; Luberadzka, Joanna; Hohmann, Volker

2018-06-01

Create virtual acoustic environments (VAEs) with interactive dynamic rendering for applications in audiology. A toolbox for creation and rendering of dynamic virtual acoustic environments (TASCAR) that allows direct user interaction was developed for application in hearing aid research and audiology. The software architecture and the simulation methods used to produce VAEs are outlined. Example environments are described and analysed. With the proposed software, a tool for simulation of VAEs is available. A set of VAEs rendered with the proposed software was described.

Automated real-time software development

NASA Technical Reports Server (NTRS)

Jones, Denise R.; Walker, Carrie K.; Turkovich, John J.

1993-01-01

A Computer-Aided Software Engineering (CASE) system has been developed at the Charles Stark Draper Laboratory (CSDL) under the direction of the NASA Langley Research Center. The CSDL CASE tool provides an automated method of generating source code and hard copy documentation from functional application engineering specifications. The goal is to significantly reduce the cost of developing and maintaining real-time scientific and engineering software while increasing system reliability. This paper describes CSDL CASE and discusses demonstrations that used the tool to automatically generate real-time application code.

Consolidated Cab Display (CCD) System, Project Planning Document (PPD),

DTIC Science & Technology

1981-02-01

1980 1981 I 2 3 4 5 6 7 8 9 10 1112 1 2 3 4 5 6 7 8 9 1011112 1 2 31 12. Software Documentation a. Overall Computer Program Description ( OCPD ) b...Approve OCPD c. Computer Program Functional Specifications (CPFS) d. Data Base Table Design Specification (DBTDS) e. Software Interface Control Document...Parts List Master Pattern and Plan View Reproducible Drawings Instruction Book Training Aids/Materials b. Software: OCPD CPFS SI CD PDS DBTDS SDD

Software analysis handbook: Software complexity analysis and software reliability estimation and prediction

NASA Technical Reports Server (NTRS)

Lee, Alice T.; Gunn, Todd; Pham, Tuan; Ricaldi, Ron

1994-01-01

This handbook documents the three software analysis processes the Space Station Software Analysis team uses to assess space station software, including their backgrounds, theories, tools, and analysis procedures. Potential applications of these analysis results are also presented. The first section describes how software complexity analysis provides quantitative information on code, such as code structure and risk areas, throughout the software life cycle. Software complexity analysis allows an analyst to understand the software structure, identify critical software components, assess risk areas within a software system, identify testing deficiencies, and recommend program improvements. Performing this type of analysis during the early design phases of software development can positively affect the process, and may prevent later, much larger, difficulties. The second section describes how software reliability estimation and prediction analysis, or software reliability, provides a quantitative means to measure the probability of failure-free operation of a computer program, and describes the two tools used by JSC to determine failure rates and design tradeoffs between reliability, costs, performance, and schedule.

Acoustic Analysis of Persian Vowels in Cochlear Implant Users: A Comparison With Hearing-impaired Children Using Hearing Aid and Normal-hearing Children.

PubMed

Jafari, Narges; Yadegari, Fariba; Jalaie, Shohreh

2016-11-01

Vowel production in essence is auditorily controlled; hence, the role of the auditory feedback in vowel production is very important. The purpose of this study was to compare formant frequencies and vowel space in Persian-speaking deaf children with cochlear implantation (CI), hearing-impaired children with hearing aid (HA), and their normal-hearing (NH) peers. A total of 40 prelingually children with hearing impairment and 20 NH groups participated in this study. Participants were native Persian speakers. The average of first formant frequency (F 1 ) and second formant frequency (F 2 ) of the six vowels were measured using Praat software (version 5.1.44). One-way analysis of variance (ANOVA) was used to analyze the differences between the three3 groups. The mean value of F 1 for vowel /i/ was significantly different (between CI and NH children and also between HA and NH groups) (F 2, 57  = 9.229, P < 0.001). For vowel /a/, the mean value of F 1 was significantly different (between HA and NH groups) (F 2, 57  = 3.707, P < 0.05). Regarding the second formant frequency, a post hoc Tukey test revealed that the differences were between HA and NH children (P < 0.05). F 2 for vowel /o/ was significantly different (F 2, 57  = 4.572, P < 0.05). Also, the mean value of F 2 for vowel /a/ was significantly different (F 2, 57  = 3.184, P < 0.05). About 1 year after implantation, the formants shift closer to those of the NH listeners who tend to have more expanded vowel spaces than hearing-impaired listeners with hearing aids. Probably, this condition is because CI has a subtly positive impact on the place of articulation of vowels. Copyright © 2016 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

A novel AIDS/HIV intelligent medical consulting system based on expert systems.

PubMed

Ebrahimi, Alireza Pour; Toloui Ashlaghi, Abbas; Mahdavy Rad, Maryam

2013-01-01

The purpose of this paper is to propose a novel intelligent model for AIDS/HIV data based on expert system and using it for developing an intelligent medical consulting system for AIDS/HIV. In this descriptive research, 752 frequently asked questions (FAQs) about AIDS/HIV are gathered from numerous websites about this disease. To perform the data mining and extracting the intelligent model, the 6 stages of Crisp method has been completed for FAQs. The 6 stages include: Business understanding, data understanding, data preparation, modelling, evaluation and deployment. C5.0 Tree classification algorithm is used for modelling. Also, rational unified process (RUP) is used to develop the web-based medical consulting software. Stages of RUP are as follows: Inception, elaboration, construction and transition. The intelligent developed model has been used in the infrastructure of the software and based on client's inquiry and keywords related FAQs are displayed to the client, according to the rank. FAQs' ranks are gradually determined considering clients reading it. Based on displayed FAQs, test and entertainment links are also displayed. The accuracy of the AIDS/HIV intelligent web-based medical consulting system is estimated to be 78.76%. AIDS/HIV medical consulting systems have been developed using intelligent infrastructure. Being equipped with an intelligent model, providing consulting services on systematic textual data and providing side services based on client's activities causes the implemented system to be unique. The research has been approved by Iranian Ministry of Health and Medical Education for being practical.

Consolidated View on Space Software Engineering Problems - An Empirical Study

NASA Astrophysics Data System (ADS)

Silva, N.; Vieira, M.; Ricci, D.; Cotroneo, D.

2015-09-01

Independent software verification and validation (ISVV) has been a key process for engineering quality assessment for decades, and is considered in several international standards. The “European Space Agency (ESA) ISVV Guide” is used for the European Space market to drive the ISVV tasks and plans, and to select applicable tasks and techniques. Software artefacts have room for improvement due to the amount if issues found during ISVV tasks. This article presents the analysis of the results of a large set of ISVV issues originated from three different ESA missions-amounting to more than 1000 issues. The study presents the main types, triggers and impacts related to the ISVV issues found and sets the path for a global software engineering improvement based on the most common deficiencies identified for space projects.

14 CFR 151.89 - Roads.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Roads. 151.89 Section 151.89 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) AIRPORTS FEDERAL AID TO AIRPORTS Project Programming Standards § 151.89 Roads. (a) Federal-aid Airport Program funds...

14 CFR 151.89 - Roads.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Roads. 151.89 Section 151.89 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) AIRPORTS FEDERAL AID TO AIRPORTS Project Programming Standards § 151.89 Roads. (a) Federal-aid Airport Program funds...

14 CFR 152.417 - Monitoring employment.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Monitoring employment. 152.417 Section 152.417 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) AIRPORTS AIRPORT AID PROGRAM Nondiscrimination in Airport Aid Program § 152.417 Monitoring employment. (a...

14 CFR 151.89 - Roads.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Roads. 151.89 Section 151.89 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) AIRPORTS FEDERAL AID TO AIRPORTS Project Programming Standards § 151.89 Roads. (a) Federal-aid Airport Program funds...

A Web-Based Computer-Aided Learning Module for an Anatomy Course Using Open Source Image Mapping Software

ERIC Educational Resources Information Center

Carleton, Renee E.

2012-01-01

Computer-aided learning (CAL) is used increasingly to teach anatomy in post-secondary programs. Studies show that augmentation of traditional cadaver dissection and model examination by CAL can be associated with positive student learning outcomes. In order to reduce costs associated with the purchase of skeletons and models and to encourage study…

Can Computer-Based Visual-Spatial Aids Lead to Increased Student Performance in Anatomy & Physiology?

ERIC Educational Resources Information Center

Kesner, Michael H.; Linzey, Alicia V.

2005-01-01

InterActive Physiology (IAP) is one of a new generation of anatomy and physiology learning aids with a broader range of sensory inputs than is possible from a static textbook or moderately dynamic lecture. This best-selling software has modules covering the muscular, respiratory, urinary, cardiovascular, and nervous systems plus a module on fluids…

A Language Translator for a Computer Aided Rapid Prototyping System.

DTIC Science & Technology

1988-03-01

PROBLEM ................... S B. THE TRADITIONAL "WATERFALL LIFE CYCLE" .. ............... 14 C. RAPID PROTOTYPING...feature of everyday life for almost the entire industrialized world. Few governments or businesses function without the aid of computer systems. Com...engineering. B. TIE TRADITIONAL "WATERFALL LIFE CYCLE" I. Characteristics The traditional method of software engineering is the "waterfall life cycle

Implementing Relational Operations in an Object-Oriented Database

DTIC Science & Technology

1992-03-01

computer aided software engineering (CASE) and computer aided design (CAD) tools. There has been some research done in the area of combining...35 2. Prograph Database Engine .................................................................. 38 III. W HY A N R/O...in most business applications where the bulk of data being stored and manipulated is simply textual or numeric data that can be stored and manipulated

From LPF to eLISA: new approach in payload software

NASA Astrophysics Data System (ADS)

Gesa, Ll.; Martin, V.; Conchillo, A.; Ortega, J. A.; Mateos, I.; Torrents, A.; Lopez-Zaragoza, J. P.; Rivas, F.; Lloro, I.; Nofrarias, M.; Sopuerta, CF.

2017-05-01

eLISA will be the first observatory in space to explore the Gravitational Universe. It will gather revolutionary information about the dark universe. This implies a robust and reliable embedded control software and hardware working together. With the lessons learnt with the LISA Pathfinder payload software as baseline, we will introduce in this short article the key concepts and new approaches that our group is working on in terms of software: multiprocessor, self-modifying-code strategies, 100% hardware and software monitoring, embedded scripting, Time and Space Partition among others.

Space Shuttle Program Primary Avionics Software System (PASS) Success Legacy - Quality and Reliability Date

NASA Technical Reports Server (NTRS)

Orr, James K.; Peltier, Daryl

2010-01-01

Thsi slide presentation reviews the avionics software system on board the space shuttle, with particular emphasis on the quality and reliability. The Primary Avionics Software System (PASS) provides automatic and fly-by-wire control of critical shuttle systems which executes in redundant computers. Charts given show the number of space shuttle flights vs time, PASS's development history, and other charts that point to the reliability of the system's development. The reliability of the system is also compared to predicted reliability.

A Software Suite for Testing SpaceWire Devices and Networks

NASA Astrophysics Data System (ADS)

Mills, Stuart; Parkes, Steve

2015-09-01

SpaceWire is a data-handling network for use on-board spacecraft, which connects together instruments, mass-memory, processors, downlink telemetry, and other on-board sub-systems. SpaceWire is simple to implement and has some specific characteristics that help it support data-handling applications in space: high-speed, low-power, simplicity, relatively low implementation cost, and architectural flexibility making it ideal for many space missions. SpaceWire provides high-speed (2 Mbits/s to 200 Mbits/s), bi-directional, full-duplex data-links, which connect together SpaceWire enabled equipment. Data-handling networks can be built to suit particular applications using point-to-point data-links and routing switches. STAR-Dundee’s STAR-System software stack has been designed to meet the needs of engineers designing and developing SpaceWire networks and devices. This paper describes the aims of the software and how those needs were met.

Reuse and Interoperability of Avionics for Space Systems

NASA Technical Reports Server (NTRS)

Hodson, Robert F.

2007-01-01

The space environment presents unique challenges for avionics. Launch survivability, thermal management, radiation protection, and other factors are important for successful space designs. Many existing avionics designs use custom hardware and software to meet the requirements of space systems. Although some space vendors have moved more towards a standard product line approach to avionics, the space industry still lacks similar standards and common practices for avionics development. This lack of commonality manifests itself in limited reuse and a lack of interoperability. To address NASA s need for interoperable avionics that facilitate reuse, several hardware and software approaches are discussed. Experiences with existing space boards and the application of terrestrial standards is outlined. Enhancements and extensions to these standards are considered. A modular stack-based approach to space avionics is presented. Software and reconfigurable logic cores are considered for extending interoperability and reuse. Finally, some of the issues associated with the design of reusable interoperable avionics are discussed.

Innovative Software Tools Measure Behavioral Alertness

NASA Technical Reports Server (NTRS)

2014-01-01

To monitor astronaut behavioral alertness in space, Johnson Space Center awarded Philadelphia-based Pulsar Informatics Inc. SBIR funding to develop software to be used onboard the International Space Station. Now used by the government and private companies, the technology has increased revenues for the firm by an average of 75 percent every year.

Unified Approach to Modeling and Simulation of Space Communication Networks and Systems

NASA Technical Reports Server (NTRS)

Barritt, Brian; Bhasin, Kul; Eddy, Wesley; Matthews, Seth

2010-01-01

Network simulator software tools are often used to model the behaviors and interactions of applications, protocols, packets, and data links in terrestrial communication networks. Other software tools that model the physics, orbital dynamics, and RF characteristics of space systems have matured to allow for rapid, detailed analysis of space communication links. However, the absence of a unified toolset that integrates the two modeling approaches has encumbered the systems engineers tasked with the design, architecture, and analysis of complex space communication networks and systems. This paper presents the unified approach and describes the motivation, challenges, and our solution - the customization of the network simulator to integrate with astronautical analysis software tools for high-fidelity end-to-end simulation. Keywords space; communication; systems; networking; simulation; modeling; QualNet; STK; integration; space networks

A method for using solid modeling CAD software to create an implant library for the fabrication of a custom abutment.

PubMed

Zhang, Jing; Zhang, Rimei; Ren, Guanghui; Zhang, Xiaojie

2017-02-01

This article describes a method that incorporates the solid modeling CAD software Solidworks with a dental milling machine to fabricate individual abutments in house. This process involves creating an implant library with 3-dimensional (3D) models and manufacturing a base, scan element, abutment, and crown anatomy. The 3D models can be imported into any dental computer-aided design and computer-aided (CAD-CAM) manufacturing system. This platform increases abutment design flexibility, as the base and scan elements can be designed to fit several shapes as needed to meet clinical requirements. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Lend Me Your Voice - A Constructivist Approach to Augmentative Communication

NASA Astrophysics Data System (ADS)

Mangiatordi, Andrea; Acosta, Micaela; Castellano, Roxana

This paper envisions a software project dedicated to disabled children with communication impairments or restrictions. The idea is to develop a costless and functional communication aid capable of voice output. This software could be a very convenient solution if used on the laptops provided by One Laptop Per Child to children in different developing countries. These laptops, together with their operating system, are designed following constructionist ideas, focused on cooperative learning and "learning learning". This work discusses the creation of a tool which is both an aid to the disabled children and a base on which inclusive context can be built in school classes. An ideal lesson plan is discussed which could be used as a guideline for teachers.

AIDS web sites face censorship under new rating schemes.

PubMed

1997-08-22

The American Civil Liberties Union (ACLU) issued a position paper regarding the software industry's proposed rating standards that will block and rate information judged unsuitable for minors. Following the U.S. Supreme Court's overturning of the Communications Decency Act, a ruling that maintains a high level of free speech protection over the Internet, the software industry began examining mechanisms to rate online content. Legislators are considering criminal penalties for those who misrate a web page. These moves are seen as damaging to HIV/AIDS prevention and safe sex information web sites that utilize jargon, street language, and explicit diagrams to teach safe sex practices to a wide audience. It is noted that related ratings and censorships do not apply to print material.

Operations analysis (study 2.1): Shuttle upper stage software requirements

NASA Technical Reports Server (NTRS)

Wolfe, R. R.

1974-01-01

An investigation of software costs related to space shuttle upper stage operations with emphasis on the additional costs attributable to space servicing was conducted. The questions and problem areas include the following: (1) the key parameters involved with software costs; (2) historical data for extrapolation of future costs; (3) elements of the basic software development effort that are applicable to servicing functions; (4) effect of multiple servicing on complexity of the operation; and (5) are recurring software costs significant. The results address these questions and provide a foundation for estimating software costs based on the costs of similar programs and a series of empirical factors.

Rotational Analysis of FTIR Spectra from Cigarette Smoke: An Application of Chem Spec II Software in the Undergraduate Laboratory

ERIC Educational Resources Information Center

Ford, Alan R.; Burns, William A.; Reeve, Scott W.

2004-01-01

A version of the classic gas phase infrared experiment was developed for students at Arkansas State University based on the shortcomings of the rotationally resolved infrared experiment. Chem Spec II is a noncommercial Windows-based software package developed to aid in the potentially complicated problem of assigning quantum numbers to observed…

A new semiquantitative method for evaluation of metastasis progression.

PubMed

Volarevic, A; Ljujic, B; Volarevic, V; Milovanovic, M; Kanjevac, T; Lukic, A; Arsenijevic, N

2012-01-01

Although recent technical advancements are directed toward developing novel assays and methods for detection of micro and macro metastasis, there are still no reports of reliable, simple to use imaging software that could be used for the detection and quantification of metastasis in tissue sections. We herein report a new semiquantitative method for evaluation of metastasis progression in a well established 4T1 orthotopic mouse model of breast cancer metastasis. The new semiquantitative method presented here was implemented by using the Autodesk AutoCAD 2012 program, a computer-aided design program used primarily for preparing technical drawings in 2 dimensions. By using the Autodesk AutoCAD 2012 software- aided graphical evaluation we managed to detect each metastatic lesion and we precisely calculated the average percentage of lung and liver tissue parenchyma with metastasis in 4T1 tumor-bearing mice. The data were highly specific and relevant to descriptive histological analysis, confirming reliability and accuracy of the AutoCAD 2012 software as new method for quantification of metastatic lesions. The new semiquantitative method using AutoCAD 2012 software provides a novel approach for the estimation of metastatic progression in histological tissue sections.

An application framework for computer-aided patient positioning in radiation therapy.

PubMed

Liebler, T; Hub, M; Sanner, C; Schlegel, W

2003-09-01

The importance of exact patient positioning in radiation therapy increases with the ongoing improvements in irradiation planning and treatment. Therefore, new ways to overcome precision limitations of current positioning methods in fractionated treatment have to be found. The Department of Medical Physics at the German Cancer Research Centre (DKFZ) follows different video-based approaches to increase repositioning precision. In this context, the modular software framework FIVE (Fast Integrated Video-based Environment) has been designed and implemented. It is both hardware- and platform-independent and supports merging position data by integrating various computer-aided patient positioning methods. A highly precise optical tracking system and several subtraction imaging techniques have been realized as modules to supply basic video-based repositioning techniques. This paper describes the common framework architecture, the main software modules and their interfaces. An object-oriented software engineering process has been applied using the UML, C + + and the Qt library. The significance of the current framework prototype for the application in patient positioning as well as the extension to further application areas will be discussed. Particularly in experimental research, where special system adjustments are often necessary, the open design of the software allows problem-oriented extensions and adaptations.

Open Drug Discovery Toolkit (ODDT): a new open-source player in the drug discovery field.

PubMed

Wójcikowski, Maciej; Zielenkiewicz, Piotr; Siedlecki, Pawel

2015-01-01

There has been huge progress in the open cheminformatics field in both methods and software development. Unfortunately, there has been little effort to unite those methods and software into one package. We here describe the Open Drug Discovery Toolkit (ODDT), which aims to fulfill the need for comprehensive and open source drug discovery software. The Open Drug Discovery Toolkit was developed as a free and open source tool for both computer aided drug discovery (CADD) developers and researchers. ODDT reimplements many state-of-the-art methods, such as machine learning scoring functions (RF-Score and NNScore) and wraps other external software to ease the process of developing CADD pipelines. ODDT is an out-of-the-box solution designed to be easily customizable and extensible. Therefore, users are strongly encouraged to extend it and develop new methods. We here present three use cases for ODDT in common tasks in computer-aided drug discovery. Open Drug Discovery Toolkit is released on a permissive 3-clause BSD license for both academic and industrial use. ODDT's source code, additional examples and documentation are available on GitHub (https://github.com/oddt/oddt).

Y0: An innovative tool for spatial data analysis

NASA Astrophysics Data System (ADS)

Wilson, Jeremy C.

1993-08-01

This paper describes an advanced analysis and visualization tool, called Y0 (pronounced ``Why not?!''), that has been developed to directly support the scientific process for earth and space science research. Y0 aids the scientific research process by enabling the user to formulate algorithms and models within an integrated environment, and then interactively explore the solution space with the aid of appropriate visualizations. Y0 has been designed to provide strong support for both quantitative analysis and rich visualization. The user's algorithm or model is defined in terms of algebraic formulas in cells on worksheets, in a similar fashion to spreadsheet programs. Y0 is specifically designed to provide the data types and rich function set necessary for effective analysis and manipulation of remote sensing data. This includes various types of arrays, geometric objects, and objects for representing geographic coordinate system mappings. Visualization of results is tailored to the needs of remote sensing, with straightforward methods of composing, comparing, and animating imagery and graphical information, with reference to geographical coordinate systems. Y0 is based on advanced object-oriented technology. It is implemented in C++ for use in Unix environments, with a user interface based on the X window system. Y0 has been delivered under contract to Unidata, a group which provides data and software support to atmospheric researches in universities affiliated with UCAR. This paper will explore the key concepts in Y0, describe its utility for remote sensing analysis and visualization, and will give a specific example of its application to the problem of measuring glacier flow rates from Landsat imagery.

SpaceWire Driver Software for Special DSPs

NASA Technical Reports Server (NTRS)

Clark, Douglas; Lux, James; Nishimoto, Kouji; Lang, Minh

2003-01-01

A computer program provides a high-level C-language interface to electronics circuitry that controls a SpaceWire interface in a system based on a space qualified version of the ADSP-21020 digital signal processor (DSP). SpaceWire is a spacecraft-oriented standard for packet-switching data-communication networks that comprise nodes connected through bidirectional digital serial links that utilize low-voltage differential signaling (LVDS). The software is tailored to the SMCS-332 application-specific integrated circuit (ASIC) (also available as the TSS901E), which provides three highspeed (150 Mbps) serial point-to-point links compliant with the proposed Institute of Electrical and Electronics Engineers (IEEE) Standard 1355.2 and equivalent European Space Agency (ESA) Standard ECSS-E-50-12. In the specific application of this software, the SpaceWire ASIC was combined with the DSP processor, memory, and control logic in a Multi-Chip Module DSP (MCM-DSP). The software is a collection of low-level driver routines that provide a simple message-passing application programming interface (API) for software running on the DSP. Routines are provided for interrupt-driven access to the two styles of interface provided by the SMCS: (1) the "word at a time" conventional host interface (HOCI); and (2) a higher performance "dual port memory" style interface (COMI).

Solar Electric Propulsion Triple-Satellite-Aided Capture With Mars Flyby

NASA Astrophysics Data System (ADS)

Patrick, Sean

Triple-Satellite-aided-capture sequences use gravity-assists at three of Jupiter's four massive Galilean moons to reduce the DeltaV required to enter into Jupiter orbit. A triple-satellite-aided capture at Callisto, Ganymede, and Io is proposed to capture a SEP spacecraft into Jupiter orbit from an interplanetary Earth-Jupiter trajectory that employs low-thrust maneuvers. The principal advantage of this method is that it combines the ISP efficiency of ion propulsion with nearly impulsive but propellant-free gravity assists. For this thesis, two main chapters are devoted to the exploration of low-thrust triple-flyby capture trajectories. Specifically, the design and optimization of these trajectories are explored heavily. The first chapter explores the design of two solar electric propulsion (SEP), low-thrust trajectories developed using the JPL's MALTO software. The two trajectories combined represent a full Earth to Jupiter capture split into a heliocentric Earth to Jupiter Sphere of Influence (SOI) trajectory and a Joviocentric capture trajectory. The Joviocentric trajectory makes use of gravity assist flybys of Callisto, Ganymede, and Io to capture into Jupiter orbit with a period of 106.3 days. Following this, in chapter two, three more SEP low-thrust trajectories were developed based upon those in chapter one. These trajectories, devised using the high-fidelity Mystic software, also developed by JPL, improve upon the original trajectories developed in chapter one. Here, the developed trajectories are each three separate, full Earth to Jupiter capture orbits. As in chapter one, a Mars gravity assist is used to augment the heliocentric trajectories. Gravity-assist flybys of Callisto, Ganymede, and Io or Europa are used to capture into Jupiter Orbit. With between 89.8 and 137.2-day periods, the orbits developed in chapters one and two are shorter than most Jupiter capture orbits achieved using low-thrust propulsion techniques. Finally, chapter 3 presents an original trajectory design for a Very-Long-Baseline Interferometry (VLBI) satellite constellation. The design was created for the 8th Global Trajectory Optimization Competition (GTOC8) in which participants are tasked with creating and optimizing low-thrust trajectories to place a series of three space craft into formation to map given radio sources.

Information technology aided exploration of system design spaces

NASA Technical Reports Server (NTRS)

Feather, Martin S.; Kiper, James D.; Kalafat, Selcuk

2004-01-01

We report on a practical application of information technology techniques to aid system engineers effectively explore large design spaces. We make use of heuristic search, visualization and data mining, the combination of which we have implemented wtihin a risk management tool in use at JPL and NASA.

A compilation of technology spinoffs from the US Space Shuttle Program

NASA Technical Reports Server (NTRS)

Jackson, David Jeff

1993-01-01

As the successful transfer of NASA-developed technology is a stated mission of NASA, the documentation of such transfer is vital in support of the program. The purpose of this report is to document technology transfer, i.e. 'spinoffs', from the U.S. Space Shuttle Program to the commercial sector. These spinoffs have their origin in the many scientific and engineering fields associated with the shuttle program and, as such, span many diverse commercial applications. These applications include, but are not limited to, consumer products, medicine, industrial productivity, manufacturing technology, public safety, resources management, materials processing, transportation, energy, computer technology, construction, and environmental applications. To aide to the generation of this technology spinoff list, significant effort was made to establish numerous and complementary sources of information. The primary sources of information used in compiling this list include: the NASA 'Spinoff' publication, NASA Tech Briefs, the Marshall Space Flight Center (MSFC) Technology Utilization (TU) Office, the NASA Center for Aerospace Information (CASI), the NASA COSMIC Software Center, and MSFC laboratory and contractor personnel. A complete listing of resources may be found in the bibliography of this report. Additionally, effort was made to insure that the obtained information was placed in electronic database form to insure that the subsequent updating would be feasible with minimal effort.

Self-assembled titanium phosphonate nanomaterial having a mesoscopic void space and its optoelectronic application.

PubMed

Pramanik, Malay; Patra, Astam K; Bhaumik, Asim

2013-04-14

Here we report the synthesis of a new crystalline titanium phosphonate material (HTiP-7) having a self-assembled nanostructure and a mesoscopic void space without the aid of any surfactant or templating agent. The material has been synthesized hydrothermally through the reaction between benzene-1,3,5-triphosphonic acid (BTPA) and titanium(iv) isopropoxide at neutral pH at 453 K for 24 h. This hybrid phosphonate material has been thoroughly characterized by powder X-ray diffraction, N2 sorption, HR TEM, FE SEM, TG-DTA, FT IR and UV-Vis diffuse reflectance spectroscopic studies. Two very well-known software packages, REFLEX and CELSIZ unit cell refinement programs, are employed to establish the triclinic crystal phase of this hybrid material (HTiP-7). Very tiny nanocrystals of HTiP-7 self-aggregated to form spherical nanoparticles of dimension ca. 25 nm together with a mesoscopic void space and good BET surface area (255 m(2) g(-1)). The framework is thermally stable up to 650 K. The material showed excellent carrier mobility for photocurrent generation in the presence of a photosensitizer molecule (Rose Bengal). To the best of our knowledge this is the first report of a photon-to-electron energy transfer process over a dye doped titanium phosphonate nanomaterial.

ARC-2007-ACD07-0140-001

NASA Image and Video Library

2007-07-31

David L. Iverson of NASA Ames Research center, Moffett Field, California, led development of computer software to monitor the conditions of the gyroscopes that keep the International Space Station (ISS) properly oriented in space as the ISS orbits Earth. The gyroscopes are flywheels that control the station's attitude without the use of propellant fuel. NASA computer scientists designed the new software, the Inductive Monitoring System, to detect warning signs that precede a gyroscope's failure. According to NASA officials, engineers will add the new software tool to a group of existing tools to identify and track problems related to the gyroscopes. If the software detects warning signs, it will quickly warn the space station's mission control center.

Using Combined SFTA and SFMECA Techniques for Space Critical Software

NASA Astrophysics Data System (ADS)

Nicodemos, F. G.; Lahoz, C. H. N.; Abdala, M. A. D.; Saotome, O.

2012-01-01

This work addresses the combined Software Fault Tree Analysis (SFTA) and Software Failure Modes, Effects and Criticality Analysis (SFMECA) techniques applied to space critical software of satellite launch vehicles. The combined approach is under research as part of the Verification and Validation (V&V) efforts to increase software dependability and as future application in other projects under development at Instituto de Aeronáutica e Espaço (IAE). The applicability of such approach was conducted on system software specification and applied to a case study based on the Brazilian Satellite Launcher (VLS). The main goal is to identify possible failure causes and obtain compensating provisions that lead to inclusion of new functional and non-functional system software requirements.

Federal Student Aid: Progress in Integrating Pell Grant and Direct Student Loan Systems and Processes, but Critical Work Remains. Report to the Secretary of Education.

ERIC Educational Resources Information Center

Powner, David A.

To address system problems and other management weaknesses, in 1998 Congress created the Office of Federal Student Aid (FSA) within the Department of Education. This office adopted a new approach to systems integration using middleware (software that can allow an application to access data residing indifferent databases) and Extensible Markup…

A Survey of CAD/CAM Technology Applications in the U.S. Shipbuilding Industry

DTIC Science & Technology

1984-01-01

operation for drafting. Computer Aided Engineering (CAE) analysis is used primarily to determine the validity of design characteristics and produc- tion...include time standard generation, sea trial analysis , and group Systems integration While no systems surveyed Aided Design (CAD) is the technology... analysis . is the largest problem involving software packages. are truly integrated, many are interfaced. Computer most interfaced category with links

Computer-Aided Argument Mapping in an EFL Setting: Does Technology Precede Traditional Paper and Pencil Approach in Developing Critical Thinking?

ERIC Educational Resources Information Center

Eftekhari, Maryam; Sotoudehnama, Elaheh; Marandi, S. Susan

2016-01-01

Developing higher-order critical thinking skills as one of the central objectives of education has been recently facilitated via software packages. Whereas one such technology as computer-aided argument mapping is reported to enhance levels of critical thinking (van Gelder 2001), its application as a pedagogical tool in English as a Foreign…

Proceedings of the Twenty-Fourth Annual Software Engineering Workshop

NASA Technical Reports Server (NTRS)

2000-01-01

On December 1 and 2, the Software Engineering Laboratory (SEL), a consortium composed of NASA/Goddard, the University of Maryland, and CSC, held the 24th Software Engineering Workshop (SEW), the last of the millennium. Approximately 240 people attended the 2-day workshop. Day 1 was composed of four sessions: International Influence of the Software Engineering Laboratory; Object Oriented Testing and Reading; Software Process Improvement; and Space Software. For the first session, three internationally known software process experts discussed the influence of the SEL with respect to software engineering research. In the Space Software session, prominent representatives from three different NASA sites- GSFC's Marti Szczur, the Jet Propulsion Laboratory's Rick Doyle, and the Ames Research Center IV&V Facility's Lou Blazy- discussed the future of space software in their respective centers. At the end of the first day, the SEW sponsored a reception at the GSFC Visitors' Center. Day 2 also provided four sessions: Using the Experience Factory; A panel discussion entitled "Software Past, Present, and Future: Views from Government, Industry, and Academia"; Inspections; and COTS. The day started with an excellent talk by CSC's Frank McGarry on "Attaining Level 5 in CMM Process Maturity." Session 2, the panel discussion on software, featured NASA Chief Information Officer Lee Holcomb (Government), our own Jerry Page (Industry), and Mike Evangelist of the National Science Foundation (Academia). Each presented his perspective on the most important developments in software in the past 10 years, in the present, and in the future.

Design and Testing of Space Telemetry SCA Waveform

NASA Technical Reports Server (NTRS)

Mortensen, Dale J.; Handler, Louis M.; Quinn, Todd M.

2006-01-01

A Software Communications Architecture (SCA) Waveform for space telemetry is being developed at the NASA Glenn Research Center (GRC). The space telemetry waveform is implemented in a laboratory testbed consisting of general purpose processors, field programmable gate arrays (FPGAs), analog-to-digital converters (ADCs), and digital-to-analog converters (DACs). The radio hardware is integrated with an SCA Core Framework and other software development tools. The waveform design is described from both the bottom-up signal processing and top-down software component perspectives. Simulations and model-based design techniques used for signal processing subsystems are presented. Testing with legacy hardware-based modems verifies proper design implementation and dynamic waveform operations. The waveform development is part of an effort by NASA to define an open architecture for space based reconfigurable transceivers. Use of the SCA as a reference has increased understanding of software defined radio architectures. However, since space requirements put a premium on size, mass, and power, the SCA may be impractical for today s space ready technology. Specific requirements for an SCA waveform and other lessons learned from this development are discussed.

Space Software Defined Radio Characterization to Enable Reuse

NASA Technical Reports Server (NTRS)

Mortensen, Dale J.; Bishop, Daniel W.; Chelmins, David

2012-01-01

NASA's Space Communication and Navigation Testbed is beginning operations on the International Space Station this year. The objective is to promote new software defined radio technologies and associated software application reuse, enabled by this first flight of NASA's Space Telecommunications Radio System architecture standard. The Space Station payload has three software defined radios onboard that allow for a wide variety of communications applications; however, each radio was only launched with one waveform application. By design the testbed allows new waveform applications to be uploaded and tested by experimenters in and outside of NASA. During the system integration phase of the testbed special waveform test modes and stand-alone test waveforms were used to characterize the SDR platforms for the future experiments. Characterization of the Testbed's JPL SDR using test waveforms and specialized ground test modes is discussed in this paper. One of the test waveforms, a record and playback application, can be utilized in a variety of ways, including new satellite on-orbit checkout as well as independent on-board testbed experiments.

Artificial intelligence and expert systems in-flight software testing

NASA Technical Reports Server (NTRS)

Demasie, M. P.; Muratore, J. F.

1991-01-01

The authors discuss the introduction of advanced information systems technologies such as artificial intelligence, expert systems, and advanced human-computer interfaces directly into Space Shuttle software engineering. The reconfiguration automation project (RAP) was initiated to coordinate this move towards 1990s software technology. The idea behind RAP is to automate several phases of the flight software testing procedure and to introduce AI and ES into space shuttle flight software testing. In the first phase of RAP, conventional tools to automate regression testing have already been developed or acquired. There are currently three tools in use.

Space shuttle on-orbit flight control software requirements, preliminary version

NASA Technical Reports Server (NTRS)

1975-01-01

Software modules associated with various flight control functions for the space shuttle orbiter are described. Data flow, interface requirements, initialization requirements and module sequencing requirements are considered. Block diagrams and tables are included.

Profile of software engineering within the National Aeronautics and Space Administration (NASA)

NASA Technical Reports Server (NTRS)

Sinclair, Craig C.; Jeletic, Kellyann F.

1994-01-01

This paper presents findings of baselining activities being performed to characterize software practices within the National Aeronautics and Space Administration. It describes how such baseline findings might be used to focus software process improvement activities. Finally, based on the findings to date, it presents specific recommendations in focusing future NASA software process improvement efforts. The findings presented in this paper are based on data gathered and analyzed to date. As such, the quantitative data presented in this paper are preliminary in nature.

IDEAS: A multidisciplinary computer-aided conceptual design system for spacecraft

NASA Technical Reports Server (NTRS)

Ferebee, M. J., Jr.

1984-01-01

During the conceptual development of advanced aerospace vehicles, many compromises must be considered to balance economy and performance of the total system. Subsystem tradeoffs may need to be made in order to satisfy system-sensitive attributes. Due to the increasingly complex nature of aerospace systems, these trade studies have become more difficult and time-consuming to complete and involve interactions of ever-larger numbers of subsystems, components, and performance parameters. The current advances of computer-aided synthesis, modeling and analysis techniques have greatly helped in the evaluation of competing design concepts. Langley Research Center's Space Systems Division is currently engaged in trade studies for a variety of systems which include advanced ground-launched space transportation systems, space-based orbital transfer vehicles, large space antenna concepts and space stations. The need for engineering analysis tools to aid in the rapid synthesis and evaluation of spacecraft has led to the development of the Interactive Design and Evaluation of Advanced Spacecraft (IDEAS) computer-aided design system. The ADEAS system has been used to perform trade studies of competing technologies and requirements in order to pinpoint possible beneficial areas for research and development. IDEAS is presented as a multidisciplinary tool for the analysis of advanced space systems. Capabilities range from model generation and structural and thermal analysis to subsystem synthesis and performance analysis.

Mechanical Prototyping and Manufacturing Internship

NASA Technical Reports Server (NTRS)

Grenfell, Peter

2016-01-01

The internship was located at the Johnson Space Center (JSC) Innovation Design Center (IDC), which is a facility where the JSC workforce can meet and conduct hands-on innovative design, fabrication, evaluation, and testing of ideas and concepts relevant to NASA's mission. The tasks of the internship included mechanical prototyping design and manufacturing projects in service of research and development as well as assisting the users of the IDC in completing their manufacturing projects. The first project was to manufacture hatch mechanisms for a team in the Systems Engineering and Project Advancement Program (SETMAP) hexacopter competition. These mechanisms were intended to improve the performance of the servomotors and offer an access point that would also seal to prevent cross-contamination. I also assisted other teams as they were constructing and modifying their hexacopters. The success of this competition demonstrated a proof of concept for aerial reconnaissance and sample return to be potentially used in future NASA missions. I also worked with Dr. Kumar Krishen to prototype an improved thermos and a novel, portable solar array. Computer-aided design (CAD) software was used to model the parts for both of these projects. Then, 3D printing as well as conventional techniques were used to produce the parts. These prototypes were then subjected to trials to determine the success of the designs. The solar array is intended to work in a cluster that is easy to set up and take down and doesn't require powered servomechanisms. It could be used terrestrially in areas not serviced by power grids. Both projects improve planetary exploration capabilities to future astronauts. Other projects included manufacturing custom rail brackets for EG-2, assisting engineers working on underwater instrument and tool cases for the NEEMO project, and helping to create mock-up parts for Space Center Houston. The use of the IDC enabled efficient completion of these projects at significantly reduced cost. I acquired and improved manufacturing and prototyping skills during my tour including learning about a CAD (Computer-Aided Design) program called Creo (Creo Parametric; design software), gaining valuable conventional machining experience with lathes, CNC (Computer Numerical Control) milling machines and various other tools, and improving my engineering project communication and collaboration skills. The internship also allowed me to better understand operations at NASA. I plan to work in the aerospace industry or do academic research benefitting space science and exploration, and this internship experience will enable me to have insight into manufacturing processes for research and development.

34 CFR 682.200 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Science and Mathematics Access to Retain Talent Grant (National SMART Grant) Program Payment period...-financial aid-related computer software at below market rental or purchase cost, and printing and...

34 CFR 682.200 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Science and Mathematics Access to Retain Talent Grant (National SMART Grant) Program Payment period...-financial aid-related computer software at below market rental or purchase cost, and printing and...

34 CFR 682.200 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Science and Mathematics Access to Retain Talent Grant (National SMART Grant) Program Payment period...-financial aid-related computer software at below market rental or purchase cost, and printing and...

Rehabilitation and Prosthetic Services

MedlinePlus

... VA Learning University (VALU) SimLearn Libraries (VALNET) VA Software Documentation Library (VDL) About VHA Learn about VHA Forms & ... & Sensory Aids Service (PSAS) Our Mission The mission of the Prosthetic & ...

Use of CCSDS Packets Over SpaceWire to Control Hardware

NASA Technical Reports Server (NTRS)

Haddad, Omar; Blau, Michael; Haghani, Noosha; Yuknis, William; Albaijes, Dennis

2012-01-01

For the Lunar Reconnaissance Orbiter, the Command and Data Handling subsystem consisted of several electronic hardware assemblies that were connected with SpaceWire serial links. Electronic hardware would be commanded/controlled and telemetry data was obtained using the SpaceWire links. Prior art focused on parallel data buses and other types of serial buses, which were not compatible with the SpaceWire and the core flight executive (CFE) software bus. This innovation applies to anything that utilizes both SpaceWire networks and the CFE software. The CCSDS (Consultative Committee for Space Data Systems) packet contains predetermined values in its payload fields that electronic hardware attached at the terminus of the SpaceWire node would decode, interpret, and execute. The hardware s interpretation of the packet data would enable the hardware to change its state/configuration (command) or generate status (telemetry). The primary purpose is to provide an interface that is compatible with the hardware and the CFE software bus. By specifying the format of the CCSDS packet, it is possible to specify how the resulting hardware is to be built (in terms of digital logic) that results in a hardware design that can be controlled by the CFE software bus in the final application

Computer-Aided Corrosion Program Management

NASA Technical Reports Server (NTRS)

MacDowell, Louis

2010-01-01

This viewgraph presentation reviews Computer-Aided Corrosion Program Management at John F. Kennedy Space Center. The contents include: 1) Corrosion at the Kennedy Space Center (KSC); 2) Requirements and Objectives; 3) Program Description, Background and History; 4) Approach and Implementation; 5) Challenges; 6) Lessons Learned; 7) Successes and Benefits; and 8) Summary and Conclusions.

Managing Complexity - Developing the Node Control Software For The International Space Station

NASA Technical Reports Server (NTRS)

Wood, Donald B.

2000-01-01

On December 4th, 1998 at 3:36 AM STS-88 (the space shuttle Endeavor) was launched with the "Node 1 Unity Module" in its payload bay. After working on the Space Station program for a very long time, that launch was one of the most beautiful sights I had ever seen! As the Shuttle proceeded to rendezvous with the Russian American module know as Zarya, I returned to Houston quickly to start monitoring the activation of the software I had spent the last 3 years working on. The FGB module (also known as "Zarya"), was grappled by the shuttle robotic arm, and connected to the Unity module. Crewmembers then hooked up the power and data connections between Zarya and Unity. On December 7th, 1998 at 9:49 PM CST the Node Control Software was activated. On December 15th, 1998, the Node-l/Zarya "cornerstone" of the International Space Station was left on-orbit. The Node Control Software (NCS) is the first software flown by NASA for the International Space Station (ISS). The ISS Program is considered the most complex international engineering effort ever undertaken. At last count some 18 countries are active partners in this global venture. NCS has performed all of its intended functions on orbit, over 200 miles above us. I'll be describing how we built the NCS software.

The Software Architecture of the Upgraded ESA DRAMA Software Suite

NASA Astrophysics Data System (ADS)

Kebschull, Christopher; Flegel, Sven; Gelhaus, Johannes; Mockel, Marek; Braun, Vitali; Radtke, Jonas; Wiedemann, Carsten; Vorsmann, Peter; Sanchez-Ortiz, Noelia; Krag, Holger

2013-08-01

In the beginnings of man's space flight activities there was the belief that space is so big that everybody could use it without any repercussions. However during the last six decades the increasing use of Earth's orbits has lead to a rapid growth in the space debris environment, which has a big influence on current and future space missions. For this reason ESA issued the "Requirements on Space Debris Mitigation for ESA Projects" [1] in 2008, which apply to all ESA missions henceforth. The DRAMA (Debris Risk Assessment and Mitigation Analysis) software suite had been developed to support the planning of space missions to comply with these requirements. During the last year the DRAMA software suite has been upgraded under ESA contract by TUBS and DEIMOS to include additional tools and increase the performance of existing ones. This paper describes the overall software architecture of the ESA DRAMA software suite. Specifically the new graphical user interface, which manages the five main tools ARES (Assessment of Risk Event Statistics), MIDAS (MASTER-based Impact Flux and Damage Assessment Software), OSCAR (Orbital Spacecraft Active Removal), CROC (Cross Section of Complex Bodies) and SARA (Re-entry Survival and Risk Analysis) is being discussed. The advancements are highlighted as well as the challenges that arise from the integration of the five tool interfaces. A framework had been developed at the ILR and was used for MASTER-2009 and PROOF-2009. The Java based GUI framework, enables the cross-platform deployment, and its underlying model-view-presenter (MVP) software pattern, meet strict design requirements necessary to ensure a robust and reliable method of operation in an environment where the GUI is separated from the processing back-end. While the GUI framework evolved with each project, allowing an increasing degree of integration of services like validators for input fields, it has also increased in complexity. The paper will conclude with an outlook on the future development of the GUI framework, where the potential for advancements will be shown.

Space Physics Data Facility Web Services

NASA Technical Reports Server (NTRS)

Candey, Robert M.; Harris, Bernard T.; Chimiak, Reine A.

2005-01-01

The Space Physics Data Facility (SPDF) Web services provides a distributed programming interface to a portion of the SPDF software. (A general description of Web services is available at http://www.w3.org/ and in many current software-engineering texts and articles focused on distributed programming.) The SPDF Web services distributed programming interface enables additional collaboration and integration of the SPDF software system with other software systems, in furtherance of the SPDF mission to lead collaborative efforts in the collection and utilization of space physics data and mathematical models. This programming interface conforms to all applicable Web services specifications of the World Wide Web Consortium. The interface is specified by a Web Services Description Language (WSDL) file. The SPDF Web services software consists of the following components: 1) A server program for implementation of the Web services; and 2) A software developer s kit that consists of a WSDL file, a less formal description of the interface, a Java class library (which further eases development of Java-based client software), and Java source code for an example client program that illustrates the use of the interface.

77 FR 74016 - Meeting of the Presidential Advisory Council on HIV/AIDS

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-12

... expertise in, or knowledge of, matters concerning HIV and AIDS, public health, global health, philanthropy....aids.gov/pacha . Public attendance at the meeting is limited to space available. Individuals who plan...

77 FR 25482 - Meeting of the Presidential Advisory Council on HIV/AIDS

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-30

... expertise in, or knowledge of, matters concerning HIV and AIDS, public health, global health, philanthropy....aids.gov/pacha . Public attendance at the meeting is limited to space available. Individuals who plan...

77 FR 40884 - Meeting of the Presidential Advisory Council on HIV/AIDS

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-11

... expertise in, or knowledge of, matters concerning HIV and AIDS, public health, global health, philanthropy....aids.gov/pacha . Public attendance at the meeting is limited to space available. Individuals who plan...

Computer-Aided-Design of the Hydraulic System of Three-Dimensional Cartridge Valve Blocks (Selected Articles)

DTIC Science & Technology

1991-03-21

sectional representation of the spatial figure can be correctly determined. 6 The AutoLisp language system in the AutoCAD software provides the most...softwares are developed on the 32-bit machines and little progress has been reported for the 16-bit machines. Even the AutoCAD is a two-ard-a-half... AutoCAD software as the basis, developed the design package of 3-D cartridge valve blocks on IM PC/AT. To realize the 3-D displaying of cartridge valves

Information systems analysis approach in hospitals: a national survey.

PubMed

Wong, B K; Sellaro, C L; Monaco, J A

1995-03-01

A survey of 216 hospitals reveals that some hospitals do not conduct cost-benefit analyses or analyze possible adverse effects in feasibility studies. In determining and analyzing system requirements, external factors that initiate the transaction are not examined, and computer-aided software engineering (CASE) tools are seldom used. Some hospitals do not investigate the advantages and disadvantages of using in-house-developed software versus purchased software packages in the evaluation of alternatives. The survey finds that, overall, most hospitals follow the traditional systems development life cycle (SDLC) approach in analyzing information systems.

LIMAO: Cross-platform software for simulating laser-induced alignment and orientation dynamics of linear-, symmetric- and asymmetric tops

NASA Astrophysics Data System (ADS)

Szidarovszky, Tamás; Jono, Maho; Yamanouchi, Kaoru

2018-07-01

A user-friendly and cross-platform software called Laser-Induced Molecular Alignment and Orientation simulator (LIMAO) has been developed. The program can be used to simulate within the rigid rotor approximation the rotational dynamics of gas phase molecules induced by linearly polarized intense laser fields at a given temperature. The software is implemented in the Java and Mathematica programming languages. The primary aim of LIMAO is to aid experimental scientists in predicting and analyzing experimental data representing laser-induced spatial alignment and orientation of molecules.

Airborne Intelligent Display (AID) Phase I Software Description,

DTIC Science & Technology

1983-10-24

Board Computer Characteristics 10 3.0 SOFTWARE GENERAL DESCRIPTION 13 3.1 Overview 13 3.2 System Software 14 3.2.1 System Startup 14 3.2.1.1 Initial...3 A-2 Task States A-4 A-3 Task Program Structure A-6 A-4 Task States and State Change Mechanisms A-7 A-5 Computing Return Addresses: RUNADR, SLPADR A...techniques. 2.2 Design Approach The stated objectives were met by: 1. distributing the processing load among multiple Z80 single-board computers (SBC’s). This

A learning apprentice for software parts composition

NASA Technical Reports Server (NTRS)

Allen, Bradley P.; Holtzman, Peter L.

1987-01-01

An overview of the knowledge acquisition component of the Bauhaus, a prototype computer aided software engineering (CASE) workstation for the development of domain-specific automatic programming systems (D-SAPS) is given. D-SAPS use domain knowledge in the refinement of a description of an application program into a compilable implementation. The approach to the construction of D-SAPS was to automate the process of refining a description of a program, expressed in an object-oriented domain language, into a configuration of software parts that implement the behavior of the domain objects.

A novel AIDS/HIV intelligent medical consulting system based on expert systems

PubMed Central

Ebrahimi, Alireza Pour; Toloui Ashlaghi, Abbas; Mahdavy Rad, Maryam

2013-01-01

Background: The purpose of this paper is to propose a novel intelligent model for AIDS/HIV data based on expert system and using it for developing an intelligent medical consulting system for AIDS/HIV. Materials and Methods: In this descriptive research, 752 frequently asked questions (FAQs) about AIDS/HIV are gathered from numerous websites about this disease. To perform the data mining and extracting the intelligent model, the 6 stages of Crisp method has been completed for FAQs. The 6 stages include: Business understanding, data understanding, data preparation, modelling, evaluation and deployment. C5.0 Tree classification algorithm is used for modelling. Also, rational unified process (RUP) is used to develop the web-based medical consulting software. Stages of RUP are as follows: Inception, elaboration, construction and transition. The intelligent developed model has been used in the infrastructure of the software and based on client's inquiry and keywords related FAQs are displayed to the client, according to the rank. FAQs’ ranks are gradually determined considering clients reading it. Based on displayed FAQs, test and entertainment links are also displayed. Result: The accuracy of the AIDS/HIV intelligent web-based medical consulting system is estimated to be 78.76%. Conclusion: AIDS/HIV medical consulting systems have been developed using intelligent infrastructure. Being equipped with an intelligent model, providing consulting services on systematic textual data and providing side services based on client's activities causes the implemented system to be unique. The research has been approved by Iranian Ministry of Health and Medical Education for being practical. PMID:24251290

Software intelligent system for effective solutions for hearing impaired subjects.

PubMed

S, Rajkumar; S, Muttan; V, Sapthagirivasan; V, Jaya; S S, Vignesh

2017-01-01

The anatomy and physiology of the ear is complex in nature, which makes it a challenge for audiologists to prescribe solutions for varied hearing-impaired subjects. There is a need to increase the satisfaction level of hearing-aid users by adopting better strategies that involve modern technological advancements. To design and develop a decision support Software Intelligent System (SIS) that performs audiological investigations to assess the degree of hearing loss and to suggest appropriate hearing-aid gain values. SIS is developed based on the study conducted in the Government General Hospital, Chennai, India, between 2013 and 2015. In the study period, audiological investigations were performed on 368 subjects, using the clinical audiometer (Inventis-Piano, Italy) and the SIS. Gain suggestions were recommended for hearing-aid users (Siemens Intuis life & Intuis-SP) using standard prescriptive procedures, alterations made by the audiologists, and by the SIS. It was developed with artificial neural network-based gain predictions. Of the tested subjects, 256 were identified as hearing-impaired. The calculated sensitivity, specificity and accuracy of the computerised audiometer incorporated in the SIS are 93%, 85% and 90% respectively. Furthermore, 86% of the hearing-impaired subjects were satisfied during their first hearing-aid trial with the gain recommendations from SIS. The findings suggest that the proposed SIS could be used to perform audiological screening tests and to recommend appropriate hearing-aid gain values to the hearing-impaired subjects. This could eventually be helpful for audiologists in the areas where routine mass audiological screening and fast hearing-aid solution is required. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Multiview Projection Using CADKEY Freeze-Frame Demonstrations.

ERIC Educational Resources Information Center

Kelso, Robert P.; Ziai, M. Reza

1988-01-01

Describes a three-dimensional computer aided design software package, CADKEY, for demonstrating orthographic orthodirectional projection theory to a classroom. Provides several figures for showing the demonstrations. (Author/YP)

Firing Room Remote Application Software Development & Swamp Works Laboratory Robot Software Development

NASA Technical Reports Server (NTRS)

Garcia, Janette

2016-01-01

The National Aeronautics and Space Administration (NASA) is creating a way to send humans beyond low Earth orbit, and later to Mars. Kennedy Space Center (KSC) is working to make this possible by developing a Spaceport Command and Control System (SCCS) which will allow the launch of Space Launch System (SLS). This paper's focus is on the work performed by the author in her first and second part of the internship as a remote application software developer. During the first part of her internship, the author worked on the SCCS's software application layer by assisting multiple ground subsystems teams including Launch Accessories (LACC) and Environmental Control System (ECS) on the design, development, integration, and testing of remote control software applications. Then, on the second part of the internship, the author worked on the development of robot software at the Swamp Works Laboratory which is a research and technology development group which focuses on inventing new technology to help future In-Situ Resource Utilization (ISRU) missions.

Proceedings of the Thirteenth Annual Software Engineering Workshop

NASA Technical Reports Server (NTRS)

1988-01-01

Topics covered in the workshop included studies and experiments conducted in the Software Engineering Laboratory (SEL), a cooperative effort of NASA Goddard Space Flight Center, the University of Maryland, and Computer Sciences Corporation; software models; software products; and software tools.

RT-Syn: A real-time software system generator

NASA Technical Reports Server (NTRS)

Setliff, Dorothy E.

1992-01-01

This paper presents research into providing highly reusable and maintainable components by using automatic software synthesis techniques. This proposal uses domain knowledge combined with automatic software synthesis techniques to engineer large-scale mission-critical real-time software. The hypothesis centers on a software synthesis architecture that specifically incorporates application-specific (in this case real-time) knowledge. This architecture synthesizes complex system software to meet a behavioral specification and external interaction design constraints. Some examples of these external constraints are communication protocols, precisions, timing, and space limitations. The incorporation of application-specific knowledge facilitates the generation of mathematical software metrics which are used to narrow the design space, thereby making software synthesis tractable. Success has the potential to dramatically reduce mission-critical system life-cycle costs not only by reducing development time, but more importantly facilitating maintenance, modifications, and extensions of complex mission-critical software systems, which are currently dominating life cycle costs.

Computer-Aided Design for Built-In-Test (CADBIT) - Software Specification. Volume 3

DTIC Science & Technology

1989-10-01

CADD COMAN WIDO IO-CNURET MSL PPLYING~ TET ATEN Figur 3-13- TUTORIA FIGUR PLCMI IN CAD-NVIOMENT ON BOAR SEFTST- 1"os-rnenu, long-tur d nnnih que- list...have software package for reliability calculation A-8 LIBRARY ELEMENT DATA SHE T’" BIT TECHNIQUE: ON-BOARD ROM CATEGORY: L’ONG TUTORIA PAGE ,5 of 14

Guidelines for Processing and Cataloging Computer Software for Schools and Area Education Agencies. Suggestions to Aid Schools and AEAs.

ERIC Educational Resources Information Center

Martin, Elizabeth; And Others

Based on definitions of a machine-readable data file (MRDF) taken from the Anglo-American Cataloging Rules, second edition (AACR2) and Standards for Cataloging Nonprint Materials, the following recommendations for processing items of computer software are provided: (1) base main and added entry determination on AACR2; (2) place designation of form…

A Collaborative Approach to Bridging the Research-Policy Gap through the Development of Policy Advice Software

ERIC Educational Resources Information Center

Milne, Barry John; Lay-Yee, Roy; McLay, Jessica; Tobias, Martin; Tuohy, Pat; Armstrong, Ann; Lynn, Robert; Pearson, Janet; Mannion, Oliver; Davis, Peter

2014-01-01

We have developed a software-based tool to support a dynamic micro-simulation model of life-course development (to age 13) as an aid to policy makers assessing the impact of policies affecting children. We demonstrate how this approach bridges the research-policy gap by creating: (1) an easy transfer of evidence in a form that policymakers can use…

CBT Pilot Program Instructional Guide. Basic Drafting Skills Curriculum Delivered through CAD Workstations and Artificial Intelligence Software.

ERIC Educational Resources Information Center

Smith, Richard J.; Sauer, Mardelle A.

This guide is intended to assist teachers in using computer-aided design (CAD) workstations and artificial intelligence software to teach basic drafting skills. The guide outlines a 7-unit shell program that may also be used as a generic authoring system capable of supporting computer-based training (CBT) in other subject areas. The first section…

Design Recovery for Software Library Population

DTIC Science & Technology

1992-12-01

increase understandability, efficiency, and maintainability of the software and the design. A good representation choice will also aid in...required for a reengineering project. It details the analysis and planning phase and gives good criteria for determining the need for a reengineering...because it deals with all of these issues. With his complete description of the analysis and planning phase, Byrne has a good foundation for

Alternatives for Developing User Documentation for Applications Software

DTIC Science & Technology

1991-09-01

style that is designed to match adult reading behaviors, using reader-based writing techniques, developing effective graphics , creating reference aids...involves research, analysis, design , and testing. The writer must have a solid understanding of the technical aspects of the document being prepared, good...ABSTRACT The preparation of software documentation is an iterative process that involves research, analysis, design , and testing. The writer must have

Generic Software for Emulating Multiprocessor Architectures.

DTIC Science & Technology

1985-05-01

RD-A157 662 GENERIC SOFTWARE FOR EMULATING MULTIPROCESSOR 1/2 AlRCHITECTURES(J) MASSACHUSETTS INST OF TECH CAMBRIDGE U LRS LAB FOR COMPUTER SCIENCE R...AREA & WORK UNIT NUMBERS MIT Laboratory for Computer Science 545 Technology Square Cambridge, MA 02139 ____________ I I. CONTROLLING OFFICE NAME AND...aide If neceeasy end Identify by block number) Computer architecture, emulation, simulation, dataf low 20. ABSTRACT (Continue an reverse slde It

Capabilities of software "Vector-M" for a diagnostics of the ionosphere state from auroral emissions images and plasma characteristics from the different orbits as a part of the system of control of space weather

NASA Astrophysics Data System (ADS)

Avdyushev, V.; Banshchikova, M.; Chuvashov, I.; Kuzmin, A.

2017-09-01

In the paper are presented capabilities of software "Vector-M" for a diagnostics of the ionosphere state from auroral emissions images and plasma characteristics from the different orbits as a part of the system of control of space weather. The software "Vector-M" is developed by the celestial mechanics and astrometry department of Tomsk State University in collaboration with Space Research Institute (Moscow) and Central Aerological Observatory of Russian Federal Service for Hydrometeorology and Environmental Monitoring. The software "Vector-M" is intended for calculation of attendant geophysical and astronomical information for the centre of mass of the spacecraft and the space of observations in the experiment with auroral imager Aurovisor-VIS/MP in the orbit of the perspective Meteor-MP spacecraft.

14 CFR 141.41 - Flight simulators, flight training devices, and training aids.

Code of Federal Regulations, 2014 CFR

2014-01-01

..., and training aids. 141.41 Section 141.41 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION... aids. An applicant for a pilot school certificate or a provisional pilot school certificate must show that its flight simulators, flight training devices, training aids, and equipment meet the following...

14 CFR 141.41 - Flight simulators, flight training devices, and training aids.

Code of Federal Regulations, 2011 CFR

2011-01-01

..., and training aids. 141.41 Section 141.41 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION... aids. An applicant for a pilot school certificate or a provisional pilot school certificate must show that its flight simulators, flight training devices, training aids, and equipment meet the following...

14 CFR 141.41 - Flight simulators, flight training devices, and training aids.

Code of Federal Regulations, 2012 CFR

2012-01-01

..., and training aids. 141.41 Section 141.41 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION... aids. An applicant for a pilot school certificate or a provisional pilot school certificate must show that its flight simulators, flight training devices, training aids, and equipment meet the following...

14 CFR 141.41 - Flight simulators, flight training devices, and training aids.

Code of Federal Regulations, 2013 CFR

2013-01-01

..., and training aids. 141.41 Section 141.41 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION... aids. An applicant for a pilot school certificate or a provisional pilot school certificate must show that its flight simulators, flight training devices, training aids, and equipment meet the following...

14 CFR 151.15 - Federal-aid Airport Program: Policy affecting runway or taxiway remarking.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Federal-aid Airport Program: Policy... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) AIRPORTS FEDERAL AID TO AIRPORTS General Requirements § 151.15 Federal-aid Airport Program: Policy affecting runway or taxiway remarking. No project for...

14 CFR 151.15 - Federal-aid Airport Program: Policy affecting runway or taxiway remarking.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Federal-aid Airport Program: Policy... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) AIRPORTS FEDERAL AID TO AIRPORTS General Requirements § 151.15 Federal-aid Airport Program: Policy affecting runway or taxiway remarking. No project for...

14 CFR 151.15 - Federal-aid Airport Program: Policy affecting runway or taxiway remarking.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Federal-aid Airport Program: Policy... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) AIRPORTS FEDERAL AID TO AIRPORTS General Requirements § 151.15 Federal-aid Airport Program: Policy affecting runway or taxiway remarking. No project for...

NASA Integrated Network Monitor and Control Software Architecture

NASA Technical Reports Server (NTRS)

Shames, Peter; Anderson, Michael; Kowal, Steve; Levesque, Michael; Sindiy, Oleg; Donahue, Kenneth; Barnes, Patrick

2012-01-01

The National Aeronautics and Space Administration (NASA) Space Communications and Navigation office (SCaN) has commissioned a series of trade studies to define a new architecture intended to integrate the three existing networks that it operates, the Deep Space Network (DSN), Space Network (SN), and Near Earth Network (NEN), into one integrated network that offers users a set of common, standardized, services and interfaces. The integrated monitor and control architecture utilizes common software and common operator interfaces that can be deployed at all three network elements. This software uses state-of-the-art concepts such as a pool of re-programmable equipment that acts like a configurable software radio, distributed hierarchical control, and centralized management of the whole SCaN integrated network. For this trade space study a model-based approach using SysML was adopted to describe and analyze several possible options for the integrated network monitor and control architecture. This model was used to refine the design and to drive the costing of the four different software options. This trade study modeled the three existing self standing network elements at point of departure, and then described how to integrate them using variations of new and existing monitor and control system components for the different proposed deployments under consideration. This paper will describe the trade space explored, the selected system architecture, the modeling and trade study methods, and some observations on useful approaches to implementing such model based trade space representation and analysis.

An approach to developing user interfaces for space systems

NASA Astrophysics Data System (ADS)

Shackelford, Keith; McKinney, Karen

1993-08-01

Inherent weakness in the traditional waterfall model of software development has led to the definition of the spiral model. The spiral model software development lifecycle model, however, has not been applied to NASA projects. This paper describes its use in developing real time user interface software for an Environmental Control and Life Support System (ECLSS) Process Control Prototype at NASA's Marshall Space Flight Center.

Technology for Manufacturing Efficiency

NASA Technical Reports Server (NTRS)

1995-01-01

The Ground Processing Scheduling System (GPSS) was developed by Ames Research Center, Kennedy Space Center and divisions of the Lockheed Company to maintain the scheduling for preparing a Space Shuttle Orbiter for a mission. Red Pepper Software Company, now part of PeopleSoft, Inc., commercialized the software as their ResponseAgent product line. The software enables users to monitor manufacturing variables, report issues and develop solutions to existing problems.

Power subsystem automation study

NASA Technical Reports Server (NTRS)

Tietz, J. C.; Sewy, D.; Pickering, C.; Sauers, R.

1984-01-01

The purpose of the phase 2 of the power subsystem automation study was to demonstrate the feasibility of using computer software to manage an aspect of the electrical power subsystem on a space station. The state of the art in expert systems software was investigated in this study. This effort resulted in the demonstration of prototype expert system software for managing one aspect of a simulated space station power subsystem.

Studies and analyses of the space shuttle main engine. Failure information propagation model data base and software

NASA Technical Reports Server (NTRS)

Tischer, A. E.

1987-01-01

The failure information propagation model (FIPM) data base was developed to store and manipulate the large amount of information anticipated for the various Space Shuttle Main Engine (SSME) FIPMs. The organization and structure of the FIPM data base is described, including a summary of the data fields and key attributes associated with each FIPM data file. The menu-driven software developed to facilitate and control the entry, modification, and listing of data base records is also discussed. The transfer of the FIPM data base and software to the NASA Marshall Space Flight Center is described. Complete listings of all of the data base definition commands and software procedures are included in the appendixes.

14 CFR 382.121 - What mobility aids and other assistive devices may passengers with a disability bring into the...

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 4 2013-01-01 2013-01-01 false What mobility aids and other assistive... Aids, and Other Assistive Devices § 382.121 What mobility aids and other assistive devices may... or collapsible wheelchairs; (2) Other mobility aids, such as canes (including those used by persons...

14 CFR 382.121 - What mobility aids and other assistive devices may passengers with a disability bring into the...

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 4 2012-01-01 2012-01-01 false What mobility aids and other assistive... Aids, and Other Assistive Devices § 382.121 What mobility aids and other assistive devices may... or collapsible wheelchairs; (2) Other mobility aids, such as canes (including those used by persons...

14 CFR 382.121 - What mobility aids and other assistive devices may passengers with a disability bring into the...

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 4 2014-01-01 2014-01-01 false What mobility aids and other assistive... Aids, and Other Assistive Devices § 382.121 What mobility aids and other assistive devices may... or collapsible wheelchairs; (2) Other mobility aids, such as canes (including those used by persons...

Integrating and Managing Bim in GIS, Software Review

NASA Astrophysics Data System (ADS)

El Meouche, R.; Rezoug, M.; Hijazi, I.

2013-08-01

Since the advent of Computer-Aided Design (CAD) and Geographical Information System (GIS) tools, project participants have been increasingly leveraging these tools throughout the different phases of a civil infrastructure project. In recent years the number of GIS software that provides tools to enable the integration of Building information in geo context has risen sharply. More and more GIS software are added tools for this purposes and other software projects are regularly extending these tools. However, each software has its different strength and weakness and its purpose of use. This paper provides a thorough review to investigate the software capabilities and clarify its purpose. For this study, Autodesk Revit 2012 i.e. BIM editor software was used to create BIMs. In the first step, three building models were created, the resulted models were converted to BIM format and then the software was used to integrate it. For the evaluation of the software, general characteristics was studied such as the user interface, what formats are supported (import/export), and the way building information are imported.

34 CFR 682.200 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Science and Mathematics Access to Retain Talent Grant (National SMART Grant) Program Payment period... equipment, or non-loan processing or non-financial aid-related computer software at below market rental or...

Computer Technology Directory.

ERIC Educational Resources Information Center

Exceptional Parent, 1990

1990-01-01

This directory lists approximately 300 commercial vendors that offer computer hardware, software, and communication aids for children with disabilities. The company listings indicate computer compatibility and specific disabilities served by their products. (JDD)

Evaluation of computer-generated guidelines for companions of paediatric patients undergoing chemotherapy.

PubMed

Lopes, Vagner José; Shmeil, Marcos Augusto Hochuli

2017-04-27

To compare computer-generated guidelines with and without the use of a Clinical Decision Support System - Oncology Care and Healthcare for Chemotherapy Patients, for the caregivers of children undergoing chemotherapy. This is a descriptive, evaluative, and quantitative study conducted at a paediatrics hospital in Curitiba, Paraná, Brazil, from December 2015 to January 2016. The sample consisted of 58 participants divided into two groups: Group 1, without the aid of software, and Group 2, with the aid of the software. The data were analysed using the Mann-Whitney U test. The guidelines revealed a statistical significance (p<0.05), with a prevalence of a higher concordance average in Group 2 in comparison with Group 1. Computer-generated guidelines are a valuable qualitative support tool for nurses.

Computer program for design and performance analysis of navigation-aid power systems. Program documentation. Volume 1: Software requirements document

NASA Technical Reports Server (NTRS)

Goltz, G.; Kaiser, L. M.; Weiner, H.

1977-01-01

A computer program has been developed for designing and analyzing the performance of solar array/battery power systems for the U.S. Coast Guard Navigational Aids. This program is called the Design Synthesis/Performance Analysis (DSPA) Computer Program. The basic function of the Design Synthesis portion of the DSPA program is to evaluate functional and economic criteria to provide specifications for viable solar array/battery power systems. The basic function of the Performance Analysis portion of the DSPA program is to simulate the operation of solar array/battery power systems under specific loads and environmental conditions. This document establishes the software requirements for the DSPA computer program, discusses the processing that occurs within the program, and defines the necessary interfaces for operation.

Computer aided analysis, simulation and optimisation of thermal sterilisation processes.

PubMed

Narayanan, C M; Banerjee, Arindam

2013-04-01

Although thermal sterilisation is a widely employed industrial process, little work is reported in the available literature including patents on the mathematical analysis and simulation of these processes. In the present work, software packages have been developed for computer aided optimum design of thermal sterilisation processes. Systems involving steam sparging, jacketed heating/cooling, helical coils submerged in agitated vessels and systems that employ external heat exchangers (double pipe, shell and tube and plate exchangers) have been considered. Both batch and continuous operations have been analysed and simulated. The dependence of del factor on system / operating parameters such as mass or volume of substrate to be sterilised per batch, speed of agitation, helix diameter, substrate to steam ratio, rate of substrate circulation through heat exchanger and that through holding tube have been analysed separately for each mode of sterilisation. Axial dispersion in the holding tube has also been adequately accounted for through an appropriately defined axial dispersion coefficient. The effect of exchanger characteristics/specifications on the system performance has also been analysed. The multiparameter computer aided design (CAD) software packages prepared are thus highly versatile in nature and they permit to make the most optimum choice of operating variables for the processes selected. The computed results have been compared with extensive data collected from a number of industries (distilleries, food processing and pharmaceutical industries) and pilot plants and satisfactory agreement has been observed between the two, thereby ascertaining the accuracy of the CAD softwares developed. No simplifying assumptions have been made during the analysis and the design of associated heating / cooling equipment has been performed utilising the most updated design correlations and computer softwares.

An Internet Protocol-Based Software System for Real-Time, Closed-Loop, Multi-Spacecraft Mission Simulation Applications

NASA Technical Reports Server (NTRS)

Davis, George; Cary, Everett; Higinbotham, John; Burns, Richard; Hogie, Keith; Hallahan, Francis

2003-01-01

The paper will provide an overview of the web-based distributed simulation software system developed for end-to-end, multi-spacecraft mission design, analysis, and test at the NASA Goddard Space Flight Center (GSFC). This software system was developed for an internal research and development (IR&D) activity at GSFC called the Distributed Space Systems (DSS) Distributed Synthesis Environment (DSE). The long-term goal of the DSS-DSE is to integrate existing GSFC stand-alone test beds, models, and simulation systems to create a "hands on", end-to-end simulation environment for mission design, trade studies and simulations. The short-term goal of the DSE was therefore to develop the system architecture, and then to prototype the core software simulation capability based on a distributed computing approach, with demonstrations of some key capabilities by the end of Fiscal Year 2002 (FY02). To achieve the DSS-DSE IR&D objective, the team adopted a reference model and mission upon which FY02 capabilities were developed. The software was prototyped according to the reference model, and demonstrations were conducted for the reference mission to validate interfaces, concepts, etc. The reference model, illustrated in Fig. 1, included both space and ground elements, with functional capabilities such as spacecraft dynamics and control, science data collection, space-to-space and space-to-ground communications, mission operations, science operations, and data processing, archival and distribution addressed.

A Distributed Simulation Software System for Multi-Spacecraft Missions

NASA Technical Reports Server (NTRS)

Burns, Richard; Davis, George; Cary, Everett

2003-01-01

The paper will provide an overview of the web-based distributed simulation software system developed for end-to-end, multi-spacecraft mission design, analysis, and test at the NASA Goddard Space Flight Center (GSFC). This software system was developed for an internal research and development (IR&D) activity at GSFC called the Distributed Space Systems (DSS) Distributed Synthesis Environment (DSE). The long-term goal of the DSS-DSE is to integrate existing GSFC stand-alone test beds, models, and simulation systems to create a "hands on", end-to-end simulation environment for mission design, trade studies and simulations. The short-term goal of the DSE was therefore to develop the system architecture, and then to prototype the core software simulation capability based on a distributed computing approach, with demonstrations of some key capabilities by the end of Fiscal Year 2002 (FY02). To achieve the DSS-DSE IR&D objective, the team adopted a reference model and mission upon which FY02 capabilities were developed. The software was prototyped according to the reference model, and demonstrations were conducted for the reference mission to validate interfaces, concepts, etc. The reference model, illustrated in Fig. 1, included both space and ground elements, with functional capabilities such as spacecraft dynamics and control, science data collection, space-to-space and space-to-ground communications, mission operations, science operations, and data processing, archival and distribution addressed.

Proceedings of the Seventeenth Annual Software Engineering Workshop

NASA Technical Reports Server (NTRS)

1992-01-01

Proceedings of the Seventeenth Annual Software Engineering Workshop are presented. The software Engineering Laboratory (SEL) is an organization sponsored by NASA/Goddard Space Flight Center and created to investigate the effectiveness of software engineering technologies when applied to the development of applications software. Topics covered include: the Software Engineering Laboratory; process measurement; software reuse; software quality; lessons learned; and is Ada dying.

Development of the Free-space Optical Communications Analysis Software (FOCAS)

NASA Technical Reports Server (NTRS)

Jeganathan, M.; Mecherle, G.; Lesh, J.

1998-01-01

The Free-space Optical Communications Analysis Software (FOCAS) was developed at the Jet Propulsion Laboratory (JPL) to provide mission planners, systems engineers and communications engineers with an easy to use tool to analyze optical communications link.

Evaluation of computer-aided diagnosis (CAD) software for the detection of lung nodules on multidetector row computed tomography (MDCT): JAFROC study for the improvement in radiologists' diagnostic accuracy.

PubMed

Hirose, Tomohiro; Nitta, Norihisa; Shiraishi, Junji; Nagatani, Yukihiro; Takahashi, Masashi; Murata, Kiyoshi

2008-12-01

The aim of this study was to evaluate the usefulness of computer-aided diagnosis (CAD) software for the detection of lung nodules on multidetector-row computed tomography (MDCT) in terms of improvement in radiologists' diagnostic accuracy in detecting lung nodules, using jackknife free-response receiver-operating characteristic (JAFROC) analysis. Twenty-one patients (6 without and 15 with lung nodules) were selected randomly from 120 consecutive thoracic computed tomographic examinations. The gold standard for the presence or absence of nodules in the observer study was determined by consensus of two radiologists. Six expert radiologists participated in a free-response receiver operating characteristic study for the detection of lung nodules on MDCT, in which cases were interpreted first without and then with the output of CAD software. Radiologists were asked to indicate the locations of lung nodule candidates on the monitor with their confidence ratings for the presence of lung nodules. The performance of the CAD software indicated that the sensitivity in detecting lung nodules was 71.4%, with 0.95 false-positive results per case. When radiologists used the CAD software, the average sensitivity improved from 39.5% to 81.0%, with an increase in the average number of false-positive results from 0.14 to 0.89 per case. The average figure-of-merit values for the six radiologists were 0.390 without and 0.845 with the output of the CAD software, and there was a statistically significant difference (P < .0001) using the JAFROC analysis. The CAD software for the detection of lung nodules on MDCT has the potential to assist radiologists by increasing their accuracy.

Making Ceramic/Polymer Parts By Extrusion Stereolithography

NASA Technical Reports Server (NTRS)

Stuffle, Kevin; Mulligan, A.; Creegan, P.; Boulton, J. M.; Lombardi, J. L.; Calvert, P. D.

1996-01-01

Extrusion stereolithography developmental method of computer-controlled manufacturing of objects out of ceramic/polymer composite materials. Computer-aided design/computer-aided manufacturing (CAD/CAM) software used to create image of desired part and translate image into motion commands for combination of mechanisms moving resin dispenser. Extrusion performed in coordination with motion of dispenser so buildup of extruded material takes on size and shape of desired part. Part thermally cured after deposition.