Energy-saving approaches to solid state street lighting

NASA Astrophysics Data System (ADS)

Vitta, Pranciškus; Stanikūnas, Rytis; Tuzikas, Arūnas; Reklaitis, Ignas; Stonkus, Andrius; Petrulis, Andrius; Vaitkevičius, Henrikas; Žukauskas, Artūras

2011-10-01

We consider the energy-saving potential of solid-state street lighting due to improved visual performance, weather sensitive luminance control and tracking of pedestrians and vehicles. A psychophysical experiment on the measurement of reaction time with a decision making task was performed under mesopic levels of illumination provided by a highpressure sodium (HPS) lamp and different solid-state light sources, such as daylight and warm-white phosphor converted light-emitting diodes (LEDs) and red-green-blue LED clusters. The results of the experiment imply that photopic luminances of road surface provided by solid-state light sources with an optimized spectral power distribution might be up to twice as low as those provided by the HPS lamp. Dynamical correction of road luminance against road surface conditions typical of Lithuanian climate was estimated to save about 20% of energy in comparison with constant-level illumination. The estimated energy savings due to the tracking of pedestrians and vehicles amount at least 25% with the cumulative effect of intelligent control of at least 40%. A solid-state street lighting system with intelligent control was demonstrated using a 300 m long test ground consisting of 10 solid-state street luminaires, a meteorological station and microwave motion sensor network operated via power line communication.

Anomalous soil radon fluctuations - signal of earthquakes in Nepal and eastern India regions

NASA Astrophysics Data System (ADS)

Deb, Argha; Gazi, Mahasin; Barman, Chiranjib

2016-12-01

The present paper deals with pre-seismic soil radon-222 recorded at two different locations 200 m apart, at Jadavpur University main campus, Kolkata, India. Solid state nuclear track detector method is used for detection of the radioactive radon gas. Two simultaneous 4-month long time series data have been analysed. Anomalous fluctuations in the radon datasets have been observed prior to recent earthquakes in Nepal and eastern India during the monitoring period, mainly, the massive 25th April 7.8 M Nepal earthquake. The simultaneous measurements assist in identifying seismogenic radon precursor efficiently.

Commissioning of the Active-Target Time Projection Chamber

NASA Astrophysics Data System (ADS)

Bradt, J.; Bazin, D.; Abu-Nimeh, F.; Ahn, T.; Ayyad, Y.; Beceiro Novo, S.; Carpenter, L.; Cortesi, M.; Kuchera, M. P.; Lynch, W. G.; Mittig, W.; Rost, S.; Watwood, N.; Yurkon, J.

2017-12-01

The Active-Target Time Projection Chamber (AT-TPC) was recently built and commissioned at the National Superconducting Cyclotron Laboratory at Michigan State University. This gas-filled detector uses an active-target design where the gas acts as both the tracking medium and the reaction target. Operating inside a 2T solenoidal magnetic field, the AT-TPC records charged particle tracks that can be reconstructed to very good energy and angular resolutions. The near- 4 π solid angle coverage and thick target of the detector are well-suited to experiments with low secondary beam intensities. In this paper, the design and instrumentation of theAT-TPC are described along with the methods used to analyze the data it produces. A simulation of the detector's performance and some results from its commissioning with a radioactive 46Ar beam are also presented.

Solid-State Nanopore.

PubMed

Yuan, Zhishan; Wang, Chengyong; Yi, Xin; Ni, Zhonghua; Chen, Yunfei; Li, Tie

2018-02-20

Solid-state nanopore has captured the attention of many researchers due to its characteristic of nanoscale. Now, different fabrication methods have been reported, which can be summarized into two broad categories: "top-down" etching technology and "bottom-up" shrinkage technology. Ion track etching method, mask etching method chemical solution etching method, and high-energy particle etching and shrinkage method are exhibited in this report. Besides, we also discussed applications of solid-state nanopore fabrication technology in DNA sequencing, protein detection, and energy conversion.

Solid-State Nanopore

NASA Astrophysics Data System (ADS)

Yuan, Zhishan; Wang, Chengyong; Yi, Xin; Ni, Zhonghua; Chen, Yunfei; Li, Tie

2018-02-01

Solid-state nanopore has captured the attention of many researchers due to its characteristic of nanoscale. Now, different fabrication methods have been reported, which can be summarized into two broad categories: "top-down" etching technology and "bottom-up" shrinkage technology. Ion track etching method, mask etching method chemical solution etching method, and high-energy particle etching and shrinkage method are exhibited in this report. Besides, we also discussed applications of solid-state nanopore fabrication technology in DNA sequencing, protein detection, and energy conversion.

Time Series Analysis of Soil Radon Data Using Multiple Linear Regression and Artificial Neural Network in Seismic Precursory Studies

NASA Astrophysics Data System (ADS)

Singh, S.; Jaishi, H. P.; Tiwari, R. P.; Tiwari, R. C.

2017-07-01

This paper reports the analysis of soil radon data recorded in the seismic zone-V, located in the northeastern part of India (latitude 23.73N, longitude 92.73E). Continuous measurements of soil-gas emission along Chite fault in Mizoram (India) were carried out with the replacement of solid-state nuclear track detectors at weekly interval. The present study was done for the period from March 2013 to May 2015 using LR-115 Type II detectors, manufactured by Kodak Pathe, France. In order to reduce the influence of meteorological parameters, statistical analysis tools such as multiple linear regression and artificial neural network have been used. Decrease in radon concentration was recorded prior to some earthquakes that occurred during the observation period. Some false anomalies were also recorded which may be attributed to the ongoing crustal deformation which was not major enough to produce an earthquake.

Nuclear particle detection using a track-recording solid

NASA Technical Reports Server (NTRS)

Weber, M.; Weber, D.

1984-01-01

The design of the nuclear particle detector located in Purdue University's Get Away Special package which was flown aboard STS-7 is detailed. The experiment consisted of a stack of particle-detecting polymer sheets. The sheets show positive results of tracks throughout the block. A slide of each sheet was made for further analysis. Recommendations for similar experiments performed in the future are discussed.

High Precision Wavelength Monitor for Tunable Laser Systems

NASA Technical Reports Server (NTRS)

Froggatt, Mark E. (Inventor); Childers, Brooks A. (Inventor)

2002-01-01

A solid-state apparatus for tracking the wavelength of a laser emission has a power splitter that divides the laser emission into at least three equal components. Differing phase shifts are detected and processed to track variations of the laser emission.

The robot's eyes - Stereo vision system for automated scene analysis

NASA Technical Reports Server (NTRS)

Williams, D. S.

1977-01-01

Attention is given to the robot stereo vision system which maintains the image produced by solid-state detector television cameras in a dynamic random access memory called RAPID. The imaging hardware consists of sensors (two solid-state image arrays using a charge injection technique), a video-rate analog-to-digital converter, the RAPID memory, and various types of computer-controlled displays, and preprocessing equipment (for reflexive actions, processing aids, and object detection). The software is aimed at locating objects and transversibility. An object-tracking algorithm is discussed and it is noted that tracking speed is in the 50-75 pixels/s range.

Relative performance of different types of passive dosimeters employing solid state nuclear track detectors.

PubMed

Jamil, K; Al-Ahmady, K K; Fazal-ur-Rehman; Ali, S; Qureshi, A A; Khan, H A

1997-10-01

Radon and its progeny, known to be carcinogenic, are a matter of great concern in underground mines and energy conserved air-tight houses. Different shapes of dosimeters using solid state nuclear track detectors (SSNTDs) have been devised to measure radon concentrations in mines and dwellings. Sometimes intercomparison of results is required by various laboratories working with solid state nuclear track detector-based passive dosimeters. The present work includes the determination of various parameters for a set of dosimeters consisting of (1) box-type, (2) pen-type, (3) tube-type, (4) Karlsruhe Diffusion Chamber, and (5) bare-type dosimeters. In this research two types of plastics, allyl-diglycol-carbonate (C12H18O7) and cellulose nitrate (C6H8O8N2) known as CR-39 and CN-85, respectively, have been employed. The detection efficiency for alpha particles from radon and its progeny for CR-39 and CN-85 have been compared. All experiments have been carried out in a custom-designed exposure chamber connected to a radon source. The calibration factors, in terms of Bq m(-3) per unit track density (1.0 cm(-2)) with respect to box-type dosimeter, have been determined for intercomparison and standardization of measured radon concentrations by a set of passive radon dosimeters used in various laboratories of the world.

Effects of etching time on alpha tracks in solid state nuclear track detectors.

PubMed

Gillmore, Gavin; Wertheim, David; Crust, Simon

2017-01-01

Solid State Nuclear Track Detectors (SSNTDs) are used extensively for monitoring alpha particle radiation, neutron flux and cosmic ray radiation. Radon gas inhalation is regarded as being a significant contributory factor to lung cancer deaths in the UK each year. Gas concentrations are often monitored using CR39 based SSNTDs as the natural decay of radon results in alpha particles which form tracks in these detectors. Such tracks are normally etched for about 4h to enable microscopic analysis. This study examined the effect of etching time on the appearance of alpha tracks in SSNTDs by collecting 2D and 3D image datasets using laser confocal microscope imaging techniques. Etching times of 2 to 4h were compared and marked differences were noted in resultant track area. The median equivalent diameters of tracks were 20.2, 30.2 and 38.9μm for etching at 2, 3 and 4h respectively. Our results indicate that modern microscope imaging can detect and image the smaller size tracks seen for example at 3h etching time. Shorter etching times may give rise to fewer coalescing tracks although there is a balance to consider as smaller track sizes may be more difficult to image. Thus etching for periods of less than 4h clearly merits further investigation as this approach has the potential to improve accuracy in assessing the number of tracks. Copyright © 2016 Elsevier B.V. All rights reserved.

Progress along developmental tracks for electronic health records implementation in the United States

PubMed Central

Hollar, David W

2009-01-01

The development and implementation of electronic health records (EHR) have occurred slowly in the United States. To date, these approaches have, for the most part, followed four developmental tracks: (a) Enhancement of immunization registries and linkage with other health records to produce Child Health Profiles (CHP), (b) Regional Health Information Organization (RHIO) demonstration projects to link together patient medical records, (c) Insurance company projects linked to ICD-9 codes and patient records for cost-benefit assessments, and (d) Consortia of EHR developers collaborating to model systems requirements and standards for data linkage. Until recently, these separate efforts have been conducted in the very silos that they had intended to eliminate, and there is still considerable debate concerning health professionals access to as well as commitment to using EHR if these systems are provided. This paper will describe these four developmental tracks, patient rights and the legal environment for EHR, international comparisons, and future projections for EHR expansion across health networks in the United States. PMID:19291284

A high-speed tracking algorithm for dense granular media

NASA Astrophysics Data System (ADS)

Cerda, Mauricio; Navarro, Cristóbal A.; Silva, Juan; Waitukaitis, Scott R.; Mujica, Nicolás; Hitschfeld, Nancy

2018-06-01

Many fields of study, including medical imaging, granular physics, colloidal physics, and active matter, require the precise identification and tracking of particle-like objects in images. While many algorithms exist to track particles in diffuse conditions, these often perform poorly when particles are densely packed together-as in, for example, solid-like systems of granular materials. Incorrect particle identification can have significant effects on the calculation of physical quantities, which makes the development of more precise and faster tracking algorithms a worthwhile endeavor. In this work, we present a new tracking algorithm to identify particles in dense systems that is both highly accurate and fast. We demonstrate the efficacy of our approach by analyzing images of dense, solid-state granular media, where we achieve an identification error of 5% in the worst evaluated cases. Going further, we propose a parallelization strategy for our algorithm using a GPU, which results in a speedup of up to 10 × when compared to a sequential CPU implementation in C and up to 40 × when compared to the reference MATLAB library widely used for particle tracking. Our results extend the capabilities of state-of-the-art particle tracking methods by allowing fast, high-fidelity detection in dense media at high resolutions.

Characterization of the Oum Er Rbia (Morocco) high basin karstic water sources by using solid state nuclear track detectors and radon as a natural tracer.

PubMed

Khalil, N; Misdaq, M A; Berrazzouk, S; Mania, J

2002-06-01

Uranium and thorium contents as well as radon alpha-activities per unit volume were evaluated inside different water samples by using a method based on calculating the CR-39 and LR-115 type II solid state nuclear track detectors (SSNTDs) detection efficiencies for the emitted alpha-particles and measuring the resulting track density rates. The validity of the SSNTD technique utilized was checked by analysing uranyl nitrate (UO2(NO3)26H2O) standard solutions. A relationship between water radon concentration and water transmission of different water sources belonging to two regions of the Middle Atlas (Morocco) water reservoir was found. The influence of the water flow rate as well as the permeability and fracture system of the host rocks of the sources studied was investigated.

Diagnostics of ion beam generated from a Mather type plasma focus device

NASA Astrophysics Data System (ADS)

Lim, L. K.; Ngoi, S. K.; Wong, C. S.; Yap, S. L.

2014-03-01

Diagnostics of ion beam emission from a 3 kJ Mather-type plasma focus device have been performed for deuterium discharge at low pressure regime. Deuterium plasma focus was found to be optimum at pressure of 0.2 mbar. The energy spectrum and total number of ions per shot from the pulsed ion beam are determined by using biased ion collectors, Faraday cup, and solid state nuclear track detector CR-39. Average energy of the ion beam obtained is about 60 keV. Total number of the ions has been determined to be in the order of 1011 per shot. Solid state nuclear track detectors (SSNTD) CR39 are employed to measure the particles at all angular direction from end on (0°) to side on (90°). Particle tracks are registered by SSNTD at 30° to 90°, except the one at the end-on 0°.

Extended papers selected from ESSDERC 2015

NASA Astrophysics Data System (ADS)

Grasser, Tibor; Schmitz, Jurriaan; Lemme, Max C.

2016-11-01

This special issue of Solid State Electronics includes 28 papers which have been carefully selected from the best presentations given at the 45th European Solid-State Device Research Conference (ESSDERC 2015) held from September 14-18, 2015 in Graz, Austria. These papers cover a wide range of topics related to the research on solid-state devices. These topics are used also to organize the conference submissions and presentations into 7 tracks: CMOS Processes, Devices and Integration; Opto-, Power- and Microwave Devices; Modeling & Simulation; Characterization, Reliability & Yield; Advanced & Emerging Memories; MEMS, Sensors & Display Technologies; Emerging Non-CMOS Devices & Technologies.

High-density near-field optical disc recording using phase change media and polycarbonate substrate

NASA Astrophysics Data System (ADS)

Shinoda, Masataka; Saito, Kimihiro; Ishimoto, Tsutomu; Kondo, Takao; Nakaoki, Ariyoshi; Furuki, Motohiro; Takeda, Minoru; Akiyama, Yuji; Shimouma, Takashi; Yamamoto, Masanobu

2004-09-01

We developed a high density near field optical recording disc system with a solid immersion lens and two laser sources. In order to realize the near field optical recording, we used a phase change recording media and a molded polycarbonate substrate. The near field optical pick-up consists of a solid immersion lens with numerical aperture of 1.84. The clear eye pattern of 90.2 GB capacity (160nm track pitch and 62 nm per bit) was observed. The jitter using a limit equalizer was 10.0 % without cross-talk. The bit error rate using an adaptive PRML with 8 taps was 3.7e-6 without cross-talk. We confirmed that the near field optical disc system is a promising technology for a next generation high density optical disc system.

Communication Satellites 1958 to 1986

DTIC Science & Technology

1984-10-01

information by tracking a ground-based beacon. The payload has redundant wideband receivers and redundant transmitters, with 230 W helix type TWTs , for...70.3, International Conference on Comrounications; ICC 󈨕 (June 1981). , and R. H. Tamashiro, "A 20 GHz 75 Watt Helix TWT for Space...WB) All solid state except TWT 10-W output Receiver 1723.3. 1726.7 MHz (NB), 1725 HHz (WB) All solid state 14-dB noise figure Antenna 2

Tracking Juvenile Recidivists: Three Options for Creating Statewide, Longitudinal Records of Juvenile Offenders.

ERIC Educational Resources Information Center

Rooney, Teresa L.

This document describes three options for a statewide statistical system for tracking recidivism of juvenile delinquents placed outside their homes in treatment programs. The information is intended for use by the state in allocating resources. The options described involve potential use of juvenile court records, placement data, and/or…

SCATS: SRB Cost Accounting and Tracking System handbook

NASA Technical Reports Server (NTRS)

Zorv, R. B.; Stewart, R. D.; Coley, G.; Higginbotham, M.

1978-01-01

The Solid Rocket Booster Cost Accounting and Tracking System (SCATS) which is an automatic data processing system designed to keep a running account of the number, description, and estimated cost of Level 2, 3, and 4 changes is described. Although designed specifically for the Space Shuttle Solid Rocket Booster Program, the ADP system can be used for any other program that has a similar structure for recording, reporting, and summing numbers and costs of changes. The program stores the alpha-numeric designators for changes, government estimated costs, proposed costs, and negotiated value in a MIRADS (Marshall Information Retrieval and Display System) format which permits rapid access, manipulation, and reporting of current change status. Output reports listing all changes, totals of each level, and totals of all levels, can be derived for any calendar interval period.

Quantifying solid waste and recycling employment in Florida, USA: Trends in public and private sectors.

PubMed

Park, Sunjoo; Yi, Hongtao; Feiock, Richard C

2015-12-01

Measuring and tracking the numbers of jobs in solid waste management and recycling industries over time provide basic data to inform decision makers about the important role played by this sector in a state or region's 'green economy'. This study estimates the number of people employed in the solid waste and recycling industry from 1989 through 2011 in the state of Florida (USA), applying a classification scheme based on the Standard Industrial Code (SIC) and utilizing the National Establishment Time Series (NETS) database. The results indicate that solid waste and recycling jobs in the private sector steadily increased from 1989 to 2011, whereas government employment for solid waste management fluctuated over the same period. © The Author(s) 2015.

Accelerating CR-39 Track Detector Processing by Utilizing UV

NASA Astrophysics Data System (ADS)

Sparling, Jonathan; Padalino, Stephen; McLean, James; Sangster, Craig; Regan, Sean

2017-10-01

The use of CR-39 plastic as a Solid State Nuclear Track Detector is an effective technique for obtaining data in high energy particle experiments including inertial confinement fusion. To reveal particle tracks after irradiation, CR-39 is chemically etched in NaOH at 80°C, producing micron-scale signal pits at the nuclear track sites. It has been shown that illuminating CR-39 with UV light prior to etching increases bulk and track etch rates, especially when combined with elevated temperature. Spectroscopic analysis for amorphous solids has helped identify which UV wavelengths are most effective at enhancing etch rates. Absorption peaks found in the near infrared range provide for efficient sample heating, and may allow targeting cooperative IR-UV chemistry. Avoiding UV induced noise can be achieved through variations in absorption depths with wavelength. Vacuum drying and water absorption tests allow measurement of the resulting variation of bulk etch rate with depth. Funded in part by the NSF and an Department of Energy Grant through the Lab of Laser Energetics.

78 FR 23291 - United States v. Ecolab Inc., et al.; Proposed Final Judgment and Competitive Impact Statement

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-18

... levels of proposed service personnel. 17. Customers choose a PCMS provider based on a number of factors... track record servicing deepwater wells, and the provider's ability to offer timely and competent service... prospective customers. New entrants can only offer chemical formulations without a track record of success or...

Solid-state coherent laser radar wind shear measuring systems

NASA Technical Reports Server (NTRS)

Huffaker, R. Milton

1992-01-01

Coherent Technologies, Inc. (CTI) was established in 1984 to engage in the development of coherent laser radar systems and subsystems with applications in atmospheric remote sensing, and in target tracking, ranging and imaging. CTI focuses its capabilities in three major areas: (1) theoretical performance and design of coherent laser radar system; (2) development of coherent laser radar systems for government agencies such as DoD and NASA; and (3) development of coherent laser radar systems for commercial markets. The topics addressed are: (1) 1.06 micron solid-state coherent laser radar system; (2) wind measurement using 1.06 micron system; and flashlamp-pumped 2.09 micron solid-state coherent laser radar system.

Solid-state optical refrigeration to sub-100 Kelvin regime

DOE Office of Scientific and Technical Information (OSTI.GOV)

Melgaard, Seth D.; Albrecht, Alexander R.; Hehlen, Markus P.

We report that since the first demonstration of net cooling twenty years ago, optical refrigeration of solids has progressed to outperform all other solid-state cooling processes. It has become the first and only solid-state refrigerator capable of reaching cryogenic temperatures, and now the first solid-state cooling below 100 K. Such substantial progress required a multi-disciplinary approach of pump laser absorption enhancement, material characterization and purification, and thermal management. Here we present the culmination of two decades of progress, the record cooling to ≈91K from room temperature.

Solid-state optical refrigeration to sub-100 Kelvin regime

DOE PAGES

Melgaard, Seth D.; Albrecht, Alexander R.; Hehlen, Markus P.; ...

2016-02-05

We report that since the first demonstration of net cooling twenty years ago, optical refrigeration of solids has progressed to outperform all other solid-state cooling processes. It has become the first and only solid-state refrigerator capable of reaching cryogenic temperatures, and now the first solid-state cooling below 100 K. Such substantial progress required a multi-disciplinary approach of pump laser absorption enhancement, material characterization and purification, and thermal management. Here we present the culmination of two decades of progress, the record cooling to ≈91K from room temperature.

Solid-state optical refrigeration to sub-100 Kelvin regime

PubMed Central

Melgaard, Seth D.; Albrecht, Alexander R.; Hehlen, Markus P.; Sheik-Bahae, Mansoor

2016-01-01

Since the first demonstration of net cooling twenty years ago, optical refrigeration of solids has progressed to outperform all other solid-state cooling processes. It has become the first and only solid-state refrigerator capable of reaching cryogenic temperatures, and now the first solid-state cooling below 100 K. Such substantial progress required a multi-disciplinary approach of pump laser absorption enhancement, material characterization and purification, and thermal management. Here we present the culmination of two decades of progress, the record cooling to ≈ 91 K from room temperature. PMID:26847703

Assessment of radar altimetry correction slopes for marine gravity recovery: A case study of Jason-1 GM data

NASA Astrophysics Data System (ADS)

Zhang, Shengjun; Li, Jiancheng; Jin, Taoyong; Che, Defu

2018-04-01

Marine gravity anomaly derived from satellite altimetry can be computed using either sea surface height or sea surface slope measurements. Here we consider the slope method and evaluate the errors in the slope of the corrections supplied with the Jason-1 geodetic mission data. The slope corrections are divided into three groups based on whether they are small, comparable, or large with respect to the 1 microradian error in the current sea surface slope models. (1) The small and thus negligible corrections include dry tropospheric correction, inverted barometer correction, solid earth tide and geocentric pole tide. (2) The moderately important corrections include wet tropospheric correction, dual-frequency ionospheric correction and sea state bias. The radiometer measurements are more preferred than model values in the geophysical data records for constraining wet tropospheric effect owing to the highly variable water-vapor structure in atmosphere. The items of dual-frequency ionospheric correction and sea state bias should better not be directly added to range observations for obtaining sea surface slopes since their inherent errors may cause abnormal sea surface slopes and along-track smoothing with uniform distribution weight in certain width is an effective strategy for avoiding introducing extra noises. The slopes calculated from radiometer wet tropospheric corrections, and along-track smoothed dual-frequency ionospheric corrections, sea state bias are generally within ±0.5 microradians and no larger than 1 microradians. (3) Ocean tide has the largest influence on obtaining sea surface slopes while most of ocean tide slopes distribute within ±3 microradians. Larger ocean tide slopes mostly occur over marginal and island-surrounding seas, and extra tidal models with better precision or with extending process (e.g. Got-e) are strongly recommended for updating corrections in geophysical data records.

The application of smart sensor techniques to a solid-state array multispectral sensor

NASA Technical Reports Server (NTRS)

Mcfadin, L. W.

1978-01-01

The solid-state array spectroradiometer (SAS) developed at JSC for remote sensing applications is a multispectral sensor which has no moving parts, is virtually maintenance-free, and has the ability to provide data which requires a minimum of processing. The instrument is based on the 42 x 342 element charge injection device (CID) detector. This system allows the combination of spectral scanning and across-track spatial scanning along with its associated digitization electronics into a single detector.

22 CFR 96.43 - Case tracking, data management, and reporting.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 22 Foreign Relations 1 2011-04-01 2011-04-01 false Case tracking, data management, and reporting. 96.43 Section 96.43 Foreign Relations DEPARTMENT OF STATE LEGAL AND RELATED SERVICES ACCREDITATION OF... Accreditation and Approval Responding to Complaints and Records and Reports Management § 96.43 Case tracking...

Tracking elk hunters with the Global Positioning System

Treesearch

L. Jack Lyon; Milo G. Burcham

1998-01-01

Global Positioning System (GPS) units were used to record hunter locations at 15 second intervals during elk hunting expeditions. This information allowed us to examine the influence of roads on hunter behavior, and along with associated time and distance data, provide a solid foundation on which a hunter density and elk vulnerability model can be developed.

Textual and shape-based feature extraction and neuro-fuzzy classifier for nuclear track recognition

NASA Astrophysics Data System (ADS)

Khayat, Omid; Afarideh, Hossein

2013-04-01

Track counting algorithms as one of the fundamental principles of nuclear science have been emphasized in the recent years. Accurate measurement of nuclear tracks on solid-state nuclear track detectors is the aim of track counting systems. Commonly track counting systems comprise a hardware system for the task of imaging and software for analysing the track images. In this paper, a track recognition algorithm based on 12 defined textual and shape-based features and a neuro-fuzzy classifier is proposed. Features are defined so as to discern the tracks from the background and small objects. Then, according to the defined features, tracks are detected using a trained neuro-fuzzy system. Features and the classifier are finally validated via 100 Alpha track images and 40 training samples. It is shown that principle textual and shape-based features concomitantly yield a high rate of track detection compared with the single-feature based methods.

Solid-State Recorders Enhance Scientific Data Collection

NASA Technical Reports Server (NTRS)

2010-01-01

Under Small Business Innovation Research (SBIR) contracts with Goddard Space Flight Center, SEAKR Engineering Inc., of Centennial, Colorado, crafted a solid-state recorder (SSR) to replace the tape recorder onboard a Spartan satellite carrying NASA's Inflatable Antenna Experiment. Work for that mission and others has helped SEAKR become the world leader in SSR technology for spacecraft. The company has delivered more than 100 systems, more than 85 of which have launched onboard NASA, military, and commercial spacecraft including imaging satellites that provide much of the high-resolution imagery for online mapping services like Google Earth.

Directional Track Selection Technique in CR39 SSNTD for lowyield reaction experiments

NASA Astrophysics Data System (ADS)

Ingenito, Francesco; Andreoli, Pierluigi; Batani, Dimitri; Bonasera, Aldo; Boutoux, Guillaume; Burgy, Frederic; Cipriani, Mattia; Consoli, Fabrizio; Cristofari, Giuseppe; De Angelis, Riccardo; Di Giorgio, Giorgio; Ducret, Jean Eric; Giulietti, Danilo; Jakubowska, Katarzyna

2018-01-01

There is a great interest in the study of p-11B aneutronic nuclear fusion reactions, both for energy production and for determination of fusion cross-sections at low energies. In this context we performed experiments at CELIA in which energetic protons, accelerated by the laser ECLIPSE, were directed toward a solid Boron target. Because of the small cross-sections at these energies the number of expected reactions is low. CR39 Solid-State Nuclear Track Detectors (SSNTD) were used to detect the alpha particles produced. Because of the low expected yield, it is difficult to discriminate the tracks due to true fusion products from those due to natural background in the CR39. To this purpose we developed a methodology of particle recognition according to their direction with respect to the detector normal, able to determine the position of their source. We applied this to the specific experiment geometry, so to select from all the tracks those due to particles coming from the region of interaction between accelerated protons and solid boron target. This technique can be of great help on the analysis of SSNTD in experiments with low yield reactions, but can be also generally applied to any experiment where particles reach the track detector with known directions, and for example to improve the detection limit of particle spectrometers using CR39.

TrackEtching - A Java based code for etched track profile calculations in SSNTDs

NASA Astrophysics Data System (ADS)

Muraleedhara Varier, K.; Sankar, V.; Gangadathan, M. P.

2017-09-01

A java code incorporating a user friendly GUI has been developed to calculate the parameters of chemically etched track profiles of ion-irradiated solid state nuclear track detectors. Huygen's construction of wavefronts based on secondary wavelets has been used to numerically calculate the etched track profile as a function of the etching time. Provision for normal incidence and oblique incidence on the detector surface has been incorporated. Results in typical cases are presented and compared with experimental data. Different expressions for the variation of track etch rate as a function of the ion energy have been utilized. The best set of values of the parameters in the expressions can be obtained by comparing with available experimental data. Critical angle for track development can also be calculated using the present code.

Birth and fetal death records and environmental exposures: promising data elements for environmental public health tracking of reproductive outcomes.

PubMed

Fitzgerald, Edward; Wartenberg, Daniel; Thompson, W Douglas; Houston, Allison

2009-01-01

We inventoried and reviewed the birth and fetal death certificates of all 50 U.S. states to identify nonstandard data items that are environmentally relevant, inexpensive to collect, and might enhance environmental public health tracking. We obtained online or requested by mail or telephone the birth certificate and fetal death record forms or formats from each state. Every state data element was compared to the 2003 standards promulgated by the National Center for Health Statistics to identify any items that are not included on the standard. We then evaluated these items for their utility in environmentally related analyses. We found three data fields of potential interest. First, although every state included residence of mother at time of delivery on the birth certificate, only four states collected information on how long the mother had lived there. This item may be useful in that it could be used to assess and reduce misclassification of environmental exposures among women during pregnancy. Second, we found that father's address was listed on the birth certificates of eight states. This data field may be useful for defining paternal environmental exposures, especially in cases where the parents do not live together. Third, parental occupation was listed on the birth certificates of 15 states and may be useful for defining parental workplace exposures. Our findings were similar for fetal death records. If these data elements are accurate and well-reported, their addition to birth, fetal death, and other health records may aid in environmental public health tracking.

Gadolinium chloride as a contrast agent for imaging wood composite components by magnetic resonance

Treesearch

Thomas L. Eberhardt; Chi-Leung So; Andrea Protti; Po-Wah So

2009-01-01

Although paramagnetic contrast agents have an established track record in medical uses of magnetic resonance imaging (MRI), only recently has a contrast agent been used for enhancing MRI images of solid wood specimens. Expanding on this concept, wood veneers were treated with a gadolinium-based contrast agent and used in a model system comprising three-ply plywood...

Using Wage Record Data To Track the Post-College Employment and Earnings of Community College Students.

ERIC Educational Resources Information Center

Friedlander, Jack

The Post-Education Employment Tracking System (PEETS), operated by the Chancellor's Office of the California Community Colleges (CCC) in cooperation with the State of California's Employment Development Department (EDD), is an automated system for tracking the post-college employment rates and earnings of community college program completers and…

CP/MAS /sup 13/C NMR spectroscopic study of chlorophyll a in the solid state

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, C.E.; Spencer, R.B.; Burger, V.T.

1983-09-01

Solid-state cross-polarization, magic-angle sample spinning carbon-13 nuclear magnetic resonance spectra have been recorded on chlorophyll a- water aggregates, methyl pyrochlorophyllide a and methyl pyropheophorbide a (derivatives that lack a phytyl chain). Spectra have also been collected under a decoupling regime in which resonances of certain hydrogen-bearing carbon atoms are suppressed. These observations are used to assign the solid state spectra.

Cross-polarization/magic-angle sample-spinning /sup 13/C NMR spectroscopic study of chlorophyll a in the solid state

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, C.E.; Spencer, R.B.; Burger, V.T.

1984-01-01

Solid-state cross-polarization/magic-angle sample-spinning /sup 13/C NMR spectra have been recorded on chlorophyll a-water aggregates, methyl pyrochlorophyllide a, and methyl pyropheophorbide a. Spectra have also been collected under a decoupling regime in which resonances of certain hydrogen-bearing carbon atoms are suppressed. These observations are used to assign the solid-state spectra. 18 references, 2 figures, 1 table.

Youth Attitude Tracking Study. Volume 1. Spring 1979.

DTIC Science & Technology

1979-08-01

2.5 .3 + .5 no " Men with guns . 1 .2 + .1 no m Slogans (e.g., Navy Makes Boys Into Men) .1 .2 + .1 no Men with...survey. Thank you. TO HAKE THIS A VALID INTERVIEW, PLEASE RECORD THE TA, STATE AND COUNTY NUNBER FRON YOUR CALL RECORD PORN . (TA) (STATE

TRIAC II. A MatLab code for track measurements from SSNT detectors

NASA Astrophysics Data System (ADS)

Patiris, D. L.; Blekas, K.; Ioannides, K. G.

2007-08-01

A computer program named TRIAC II written in MATLAB and running with a friendly GUI has been developed for recognition and parameters measurements of particles' tracks from images of Solid State Nuclear Track Detectors. The program, using image analysis tools, counts the number of tracks and depending on the current working mode classifies them according to their radii (Mode I—circular tracks) or their axis (Mode II—elliptical tracks), their mean intensity value (brightness) and their orientation. Images of the detectors' surfaces are input to the code, which generates text files as output, including the number of counted tracks with the associated track parameters. Hough transform techniques are used for the estimation of the number of tracks and their parameters, providing results even in cases of overlapping tracks. Finally, it is possible for the user to obtain informative histograms as well as output files for each image and/or group of images. Program summaryTitle of program:TRIAC II Catalogue identifier:ADZC_v1_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/ADZC_v1_0 Program obtainable from: CPC Program Library, Queen's University of Belfast, N. Ireland Computer: Pentium III, 600 MHz Installations: MATLAB 7.0 Operating system under which the program has been tested: Windows XP Programming language used:MATLAB Memory required to execute with typical data:256 MB No. of bits in a word:32 No. of processors used:one Has the code been vectorized or parallelized?:no No. of lines in distributed program, including test data, etc.:25 964 No. of bytes in distributed program including test data, etc.: 4 354 510 Distribution format:tar.gz Additional comments: This program requires the MatLab Statistical toolbox and the Image Processing Toolbox to be installed. Nature of physical problem: Following the passage of a charged particle (protons and heavier) through a Solid State Nuclear Track Detector (SSNTD), a damage region is created, usually named latent track. After the chemical etching of the detectors in aqueous NaOH or KOH solutions, latent tracks can be sufficiently enlarged (with diameters of 1 μm or more) to become visible under an optical microscope. Using the appropriate apparatus, one can record images of the SSNTD's surface. The shapes of the particle's tracks are strongly dependent on their charge, energy and the angle of incidence. Generally, they have elliptical shapes and in the special case of vertical incidence, they are circular. The manual counting of tracks is a tedious and time-consuming task. An automatic system is needed to speed up the process and to increase the accuracy of the results. Method of solution: TRIAC II is based on a segmentation method that groups image pixels according to their intensity value (brightness) in a number of grey level groups. After the segmentation of pixels, the program recognizes and separates the track from the background, subsequently performing image morphology, where oversized objects or objects smaller than a threshold value are removed. Finally, using the appropriate Hough transform technique, the program counts the tracks, even those which overlap and classifies them according to their shape parameters and brightness. Typical running time: The analysis of an image with a PC (Intel Pentium III processor running at 600 MHz) requires 2 to 10 minutes, depending on the number of observed tracks and the digital resolution of the image. Unusual features of the program: This program has been tested with images of CR-39 detectors exposed to alpha particles. Also, in low contrast images with few or small tracks, background pixels can be recognized as track pixels. To avoid this problem the brightness of the background pixels should be sufficiently higher than that of the track pixels.

40 CFR 96.353 - Recordation of CAIR NOX Ozone Season allowance allocations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 21 2011-07-01 2011-07-01 false Recordation of CAIR NOX Ozone Season... STATE IMPLEMENTATION PLANS CAIR NOX Ozone Season Allowance Tracking System § 96.353 Recordation of CAIR NOX Ozone Season allowance allocations. (a) By September 30, 2007, the Administrator will record in...

40 CFR 96.353 - Recordation of CAIR NOX Ozone Season allowance allocations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 22 2012-07-01 2012-07-01 false Recordation of CAIR NOX Ozone Season... STATE IMPLEMENTATION PLANS CAIR NOX Ozone Season Allowance Tracking System § 96.353 Recordation of CAIR NOX Ozone Season allowance allocations. (a) By September 30, 2007, the Administrator will record in...

40 CFR 96.353 - Recordation of CAIR NOX Ozone Season allowance allocations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 22 2013-07-01 2013-07-01 false Recordation of CAIR NOX Ozone Season... STATE IMPLEMENTATION PLANS CAIR NOX Ozone Season Allowance Tracking System § 96.353 Recordation of CAIR NOX Ozone Season allowance allocations. (a) By September 30, 2007, the Administrator will record in...

40 CFR 96.353 - Recordation of CAIR NOX Ozone Season allowance allocations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Recordation of CAIR NOX Ozone Season... STATE IMPLEMENTATION PLANS CAIR NOX Ozone Season Allowance Tracking System § 96.353 Recordation of CAIR NOX Ozone Season allowance allocations. (a) By September 30, 2007, the Administrator will record in...

40 CFR 96.353 - Recordation of CAIR NOX Ozone Season allowance allocations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 21 2014-07-01 2014-07-01 false Recordation of CAIR NOX Ozone Season... STATE IMPLEMENTATION PLANS CAIR NOX Ozone Season Allowance Tracking System § 96.353 Recordation of CAIR NOX Ozone Season allowance allocations. (a) By September 30, 2007, the Administrator will record in...

On the track to silica-supported tungsten oxo metathesis catalysts: input from 17O solid-state NMR.

PubMed

Merle, Nicolas; Girard, Guillaume; Popoff, Nicolas; De Mallmann, Aimery; Bouhoute, Yassine; Trébosc, Julien; Berrier, Elise; Paul, Jean-François; Nicholas, Christopher P; Del Rosal, Iker; Maron, Laurent; Gauvin, Régis M; Delevoye, Laurent; Taoufik, Mostafa

2013-09-03

The grafting of an oxo chloro trisalkyl tungsten derivative on silica dehydroxylated at 700 °C was studied by several techniques that showed reaction via W-Cl cleavage, to afford a well-defined precatalyst for alkene metathesis. This was further confirmed by DFT calculations on the grafting process. (17)O labeling of the oxo moiety of a series of related molecular and supported tungsten oxo derivatives was achieved, and the corresponding (17)O MAS NMR spectra were recorded. Combined experimental and theoretical NMR studies yielded information on the local structure of the surface species. Assessment of the (17)O NMR parameters also confirmed the nature of the grafting pathway by ruling out other possible grafting schemes, thanks to highly characteristic anisotropic features arising from the quadrupolar and chemical shift interactions.

Effect of inclination direction on recording performance of BPM with inclined anisotropy

NASA Astrophysics Data System (ADS)

Honda, Naoki; Yamakawa, Kiyoshi; Ouchi, Kazuhiro; Komukai, Tatsuya

Effect of inclination direction on the recording performance of bit-patterned media with weakly inclined anisotropy was investigated by simulation. Magnetic dots with a size of 15x7.5x5 nm3 were arranged on a soft magnetic underlayer with an areal density of 2.6 Tdot/in2. Saturation magnetization of each dot was assumed to be 1000 emu/cm3. Media with three different inclination directions with an inclination angle of 30 degrees from the film normal, which were down-track inclined, cross-track inclined and cone-state, were investigated for the recording performance using a shielded planar head field. Although the three media exhibited almost the same remanence curve, obtained recording performance indicated different write shift margins. It was found that the write shift margin in the cross-track direction increased for the media with fixed inclined anisotropy axes, but the medium with the inclination direction in the cross-track direction exhibited larger shift margin than that of the down-track inclined medium when the anisotropy field dispersion was increased to 4%, while increase in the write shift margin in the downtrack direction was similar for down- and cross-track inclined media. The cause of the difference was primarily explained by the composite anisotropy of the elongated dot with the shape anisotropy in the cross-track direction.

Monitoring Cocrystal Formation via In Situ Solid-State NMR.

PubMed

Mandala, Venkata S; Loewus, Sarel J; Mehta, Manish A

2014-10-02

A detailed understanding of the mechanism of organic cocrystal formation remains elusive. Techniques that interrogate a reacting system in situ are preferred, though experimentally challenging. We report here the results of a solid-state in situ NMR study of the spontaneous formation of a cocrystal between a pharmaceutical mimic (caffeine) and a coformer (malonic acid). Using (13)C magic angle spinning NMR, we show that the formation of the cocrystal may be tracked in real time. We find no direct evidence for a short-lived, chemical shift-resolved amorphous solid intermediate. However, changes in the line width and line center of the malonic acid methylene resonance, in the course of the reaction, provide subtle clues to the mode of mass transfer that underlies cocrystal formation.

Tracking brain states under general anesthesia by using global coherence analysis.

PubMed

Cimenser, Aylin; Purdon, Patrick L; Pierce, Eric T; Walsh, John L; Salazar-Gomez, Andres F; Harrell, Priscilla G; Tavares-Stoeckel, Casie; Habeeb, Kathleen; Brown, Emery N

2011-05-24

Time and frequency domain analyses of scalp EEG recordings are widely used to track changes in brain states under general anesthesia. Although these analyses have suggested that different spatial patterns are associated with changes in the state of general anesthesia, the extent to which these patterns are spatially coordinated has not been systematically characterized. Global coherence, the ratio of the largest eigenvalue to the sum of the eigenvalues of the cross-spectral matrix at a given frequency and time, has been used to analyze the spatiotemporal dynamics of multivariate time-series. Using 64-lead EEG recorded from human subjects receiving computer-controlled infusions of the anesthetic propofol, we used surface Laplacian referencing combined with spectral and global coherence analyses to track the spatiotemporal dynamics of the brain's anesthetic state. During unconsciousness the spectrograms in the frontal leads showed increasing α (8-12 Hz) and δ power (0-4 Hz) and in the occipital leads δ power greater than α power. The global coherence detected strong coordinated α activity in the occipital leads in the awake state that shifted to the frontal leads during unconsciousness. It revealed a lack of coordinated δ activity during both the awake and unconscious states. Although strong frontal power during general anesthesia-induced unconsciousness--termed anteriorization--is well known, its possible association with strong α range global coherence suggests highly coordinated spatial activity. Our findings suggest that combined spectral and global coherence analyses may offer a new approach to tracking brain states under general anesthesia.

31P Solid-state NMR based monitoring of permeation of cell penetrating peptides into skin

PubMed Central

Desai, Pinaki R.; Cormier, Ashley R.; Shah, Punit P.; Patlolla, Ram R.; Paravastu, Anant K.; Singh, Mandip

2013-01-01

The main objective of the current study was to investigate penetration of cell penetrating peptides (CPPs: TAT, R8, R11 and YKA) through skin intercellular lipids using 31P magic angle spinning (MAS) solid-state NMR. In vitro skin permeation studies were performed on rat skin, sections (0–60, 61–120 and 121–180 µm) were collected and analyzed for 31P NMR signal. The concentration dependent shift of 0, 25, 50, 100 and 200 mg/ml of TAT on skin layers, diffusion of TAT, R8, R11 and YKA in the skin and time dependent permeation of R11 was measured on various skin sections using 31P solid-state NMR. Further, CPPs and CPP-tagged fluorescent dye encapsulate liposomes (FLip) in skin layers were tagged using confocal microscopy. The change in 31P NMR chemical shift was found to depend monotonically on the amount of CPP applied on skin, with saturation behavior above 100 mg/ml CPP concentration. R11 and TAT caused more shift in solid-state NMR peaks compared to other peptides. Furthermore, NMR spectra showed R11 penetration up to 180 µm within 30 min. The results of the solid-state NMR study were in agreement with confocal microscopy studies. Thus, 31P solid-state NMR can be used to track CPP penetration into different skin layers. PMID:23702274

Covert enaction at work: Recording the continuous movements of visuospatial attention to visible or imagined targets by means of Steady-State Visual Evoked Potentials (SSVEPs).

PubMed

Gregori Grgič, Regina; Calore, Enrico; de'Sperati, Claudio

2016-01-01

Whereas overt visuospatial attention is customarily measured with eye tracking, covert attention is assessed by various methods. Here we exploited Steady-State Visual Evoked Potentials (SSVEPs) - the oscillatory responses of the visual cortex to incoming flickering stimuli - to record the movements of covert visuospatial attention in a way operatively similar to eye tracking (attention tracking), which allowed us to compare motion observation and motion extrapolation with and without eye movements. Observers fixated a central dot and covertly tracked a target oscillating horizontally and sinusoidally. In the background, the left and the right halves of the screen flickered at two different frequencies, generating two SSVEPs in occipital regions whose size varied reciprocally as observers attended to the moving target. The two signals were combined into a single quantity that was modulated at the target frequency in a quasi-sinusoidal way, often clearly visible in single trials. The modulation continued almost unchanged when the target was switched off and observers mentally extrapolated its motion in imagery, and also when observers pointed their finger at the moving target during covert tracking, or imagined doing so. The amplitude of modulation during covert tracking was ∼25-30% of that measured when observers followed the target with their eyes. We used 4 electrodes in parieto-occipital areas, but similar results were achieved with a single electrode in Oz. In a second experiment we tested ramp and step motion. During overt tracking, SSVEPs were remarkably accurate, showing both saccadic-like and smooth pursuit-like modulations of cortical responsiveness, although during covert tracking the modulation deteriorated. Covert tracking was better with sinusoidal motion than ramp motion, and better with moving targets than stationary ones. The clear modulation of cortical responsiveness recorded during both overt and covert tracking, identical for motion observation and motion extrapolation, suggests to include covert attention movements in enactive theories of mental imagery. Copyright © 2015 Elsevier Ltd. All rights reserved.

Experimental Study of Proton Acceleration from Ultra Intense Laser Matter Interactions

NASA Astrophysics Data System (ADS)

Paudel, Yadab Kumar

This dissertation describes proton and ion acceleration measurements from high intensity (˜ 1019 Wcm-2) laser interactions with thin foil targets. Protons and ions accelerated from the back surface of a target driven by a high intensity laser are detected using solid-state nuclear track detector CR39. A simple digital imaging technique, with an adjustable halogen light source shined on CR39 and use of a digital camera with suitable f-number and exposure time, is used to detect particles tracks. This new technique improves the quality 2D image with vivid track patterns in CR39. Our technique allows us to quickly record and sort CR39 pieces for further analysis. This is followed by detailed quantitative information on the protons and ions. Protons and multicharged ions generated from high-intensity laser interactions with thin foil targets have been studied with a 100 TW laser system. Protons/ions with energies up to 10 MeV are accelerated either from the front or the rear surface of the target material. We have observed for the first time a self-radiograph of the target with a glass stalk holding the target itself in the stacked radiochromic films (RCF) placed behind the target. The self-radiography indicates that the fast ions accelerated backward, in a direction opposite to the laser propagation, are turning around in strong magnetic fields. This unique result is a signature of long-living (ns time scale) magnetic fields in the expanding plasma, which are important in energy transport during the intense laser irradiation and have never been considered in the previous studies. The magnetic fields induced by the main pulse near the absorption point expand rapidly with the backward accelerated protons in the pre-formed plasma. The protons are rotated by these magnetic fields and they are recorded in the RCF, making the self-radiography. Angular profiles of protons and multicharged ions accelerated from the target rear surface have been studied with the subpicosecond laser pulse produced by the 100 TW laser system. The protons/ions beam features recorded on CR39 show the hollow beam structure at the center of the beam pattern. This hollow structure in the proton/ion beam pattern associates to the electron transport inside the solid target, which affects the target's rear-surface emission or the electrostatic profile on the target rear-surface. The proton/ion beam filamentation has been seen clearly outside the hollow beam pattern in the CR39 images processed by the new digital imaging technique.

Solid waste information and tracking system server conversion project management plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

MAY, D.L.

1999-04-12

The Project Management Plan governing the conversion of Solid Waste Information and Tracking System (SWITS) to a client-server architecture. The Solid Waste Information and Tracking System Project Management Plan (PMP) describes the background, planning and management of the SWITS conversion. Requirements and specification documentation needed for the SWITS conversion will be released as supporting documents.

Institutional factors in resource recovery co-disposal demonstration project, Middlesex County, New Jersey, Spring 1980 - Summer 1981

NASA Astrophysics Data System (ADS)

McCarthy, R. M.

1982-02-01

A proposal to provide 1200 tons per day of solid waste disposal combined with 200 tons per day of sludge disposal was presented. The prospects for codisposal in Middlesex County were analyzed. Technically, codisposal was possible, however, it lacked a proven track record. Proposal for a resource recovery plant to be designed, built, and operated was acknowledged as consistent with County planning.

An unattended device for high-voltage sampling and passive measurement of thoron decay products.

PubMed

Gierl, Stefanie; Meisenberg, Oliver; Haninger, Thomas; Wielunski, Marek; Tschiersch, Jochen

2014-02-01

An integrating measurement device for the concentration of airborne thoron decay products was designed and calibrated. It is suitable for unattended use over up to several months also in inhabited dwellings. The device consists of a hemispheric capacitor with a wire mesh as the outer electrode on ground potential and the sampling substrates as the inner electrode on +7.0 kV. Negatively charged and neutral thoron decay products are accelerated to and deposited on the sampling substrates. As sampling substrates, CR39 solid-state nuclear track detectors are used in order to record the alpha decay of the sampled decay products. Nuclide discrimination is achieved by covering the detectors with aluminum foil of different thickness, which are penetrated only by alpha particles with sufficient energy. Devices of this type were calibrated against working level monitors in a thoron experimental house. The sensitivity was measured as 9.2 tracks per Bq/m(3) × d of thoron decay products. The devices were used over 8 weeks in several houses built of earthen material in southern Germany, where equilibrium equivalent concentrations of 1.4-9.9 Bq/m(3) of thoron decay products were measured.

Charge transport in strongly coupled quantum dot solids

NASA Astrophysics Data System (ADS)

Kagan, Cherie R.; Murray, Christopher B.

2015-12-01

The emergence of high-mobility, colloidal semiconductor quantum dot (QD) solids has triggered fundamental studies that map the evolution from carrier hopping through localized quantum-confined states to band-like charge transport in delocalized and hybridized states of strongly coupled QD solids, in analogy with the construction of solids from atoms. Increased coupling in QD solids has led to record-breaking performance in QD devices, such as electronic transistors and circuitry, optoelectronic light-emitting diodes, photovoltaic devices and photodetectors, and thermoelectric devices. Here, we review the advances in synthesis, assembly, ligand treatments and doping that have enabled high-mobility QD solids, as well as the experiments and theory that depict band-like transport in the QD solid state. We also present recent QD devices and discuss future prospects for QD materials and device design.

Charge transport in strongly coupled quantum dot solids.

PubMed

Kagan, Cherie R; Murray, Christopher B

2015-12-01

The emergence of high-mobility, colloidal semiconductor quantum dot (QD) solids has triggered fundamental studies that map the evolution from carrier hopping through localized quantum-confined states to band-like charge transport in delocalized and hybridized states of strongly coupled QD solids, in analogy with the construction of solids from atoms. Increased coupling in QD solids has led to record-breaking performance in QD devices, such as electronic transistors and circuitry, optoelectronic light-emitting diodes, photovoltaic devices and photodetectors, and thermoelectric devices. Here, we review the advances in synthesis, assembly, ligand treatments and doping that have enabled high-mobility QD solids, as well as the experiments and theory that depict band-like transport in the QD solid state. We also present recent QD devices and discuss future prospects for QD materials and device design.

A study of amplifying the response of an LR115 solid state track detector by combining it with electret.

PubMed

Nikezić, D; Krstić, D

1995-12-01

Radon progeny are positively charged immediately after formation. A negatively charged electret collects radon progeny atoms which are produced in the diffusion chamber. The detector sensitivity may be increased by using an electret in front of solid state nuclear track detector. Dependence of detection sensitivity on distance between electret and detector LR115 II is studied theoretically and experimentally in this paper. A relatively small fraction of 218Po atoms that formed in the diffusion chamber are collected by the electret. We estimated that the attracted fraction of 218Po was 17% while the attracted fraction of 214Bi-214Po is considerably larger and amounted to approximately 60%. These results confirm previous finding that 218Po atoms discharge quickly after their formation. The comparative radon measurements using diffusion chambers with and without electrets were performed. The amplification of detector sensitivity due to the electret amounted to approximately 80%.

Diagnostics of ion beam generated from a Mather type plasma focus device

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lim, L. K., E-mail: yapsl@um.edu.my; Ngoi, S. K., E-mail: yapsl@um.edu.my; Wong, C. S., E-mail: yapsl@um.edu.my

Diagnostics of ion beam emission from a 3 kJ Mather-type plasma focus device have been performed for deuterium discharge at low pressure regime. Deuterium plasma focus was found to be optimum at pressure of 0.2 mbar. The energy spectrum and total number of ions per shot from the pulsed ion beam are determined by using biased ion collectors, Faraday cup, and solid state nuclear track detector CR-39. Average energy of the ion beam obtained is about 60 keV. Total number of the ions has been determined to be in the order of 10{sup 11} per shot. Solid state nuclear trackmore » detectors (SSNTD) CR39 are employed to measure the particles at all angular direction from end on (0°) to side on (90°). Particle tracks are registered by SSNTD at 30° to 90°, except the one at the end-on 0°.« less

Real-Time Environmental Artic Monitoring (R-TEAM).

DTIC Science & Technology

1987-11-01

critical points of the mooring. Tension, tilt, pressure and temperature data are recorded on solid state memory for the duration of the deployment. Two...To iUe Tna£ LA6aksIIorZ. Um DESCaiPTiow r oj.t.TAK 2ALUMINUM PIPE -ob.I’ -WALL. 5e1 . Sm IVI IlSdh7 Z BOT’TOM END CAPME G,15473 (5 2 R.OD 3__ MX 306 as...described in Reference 2. Each instrument, located at a critical point of the mooring, measures and records in solid state memory tension, tilt, temperature

Micromagnetic structure in Co-alloy thin films and its correlation with microstructure

NASA Astrophysics Data System (ADS)

Tang, Kai

The development of magnetic hard disk recording has resulted in an increase of recording density in an accelerated pace. How to maintain the increasingly smaller bits with low noise presents a tremendous challenge to the recording media, which requires detailed study of micromagnetic structure of the media to understand the noise mechanism, and elucidation of the correlation between the micromagnetic structure and microstructure to systematically develop media materials and tailor their microstructure. Lorentz transmission electron microscopy (LTEM) is a high-resolution magnetic imaging technique. However, it requires uniformly thin specimens, which cannot be produced by conventional TEM specimen preparation methods. Consequently, its application to real computer magnetic hard disks has been limited. In this dissertation, a combined dimpling and chemical etching method is introduced to prepare specimens directly from the unmodified hard disks with the typical C/Co alloy/Cr/NiP/Al (substrate) structure. The specimens typically have 2000 μmsp2 or larger electron transparent areas of Co alloy/Cr films with uniform thickness, which are suitable for LTEM observation. This method is applicable to disks with both smooth and mechanically textured substrates. In this work, LTEM has been employed to study recorded patterns in real hard disks. Magnetic recording was performed on a standard spin stand. Bits of densities from 15 to 100 kfci were examined with head skew angles of 0sp° and 20sp°, respectively. We also compared tracks recorded on dc-erased disks with those on as-deposited disks. We observed magnetic ripples within the tracks and the inter-track regions, magnetic vortices of 0.1-0.2 mum in diameter at the bit-transitions, and curved magnetic domain walls in the track-edge regions resulting from the "dog-bone" shaped head field profile. Our results also indicate that the micromagnetic structure at the track edges is influenced by head skew and magnetization direction in the inter-track regions. The LTEM results are combined with MFM observations to provide further understanding. The study has concentrated on isotropic media on smooth substrates since low head-to-medium spacing required by high recording density demonstrates the need for this type of media. The recorded tracks are remanent magnetic states after a strong (head) magnetic field was applied. We also examined an ac-erased state, in which the effect of external field is removed. Magnetic vortices are identified, in which small crystal grains form magnetic clusters and these clusters then form closed-fluxed vortices. The size of these vortices is estimated to be around 1.0-1.5 mum, about 10 times larger than that found in the bit-transition regions. The smaller vortex sizes in the bit-transition regions may result from constraints from adjacent bits as well as the difference in magnetic processes generating these states. (Abstract shortened by UMI.)

A parametric finite element method for solid-state dewetting problems with anisotropic surface energies

NASA Astrophysics Data System (ADS)

Bao, Weizhu; Jiang, Wei; Wang, Yan; Zhao, Quan

2017-02-01

We propose an efficient and accurate parametric finite element method (PFEM) for solving sharp-interface continuum models for solid-state dewetting of thin films with anisotropic surface energies. The governing equations of the sharp-interface models belong to a new type of high-order (4th- or 6th-order) geometric evolution partial differential equations about open curve/surface interface tracking problems which include anisotropic surface diffusion flow and contact line migration. Compared to the traditional methods (e.g., marker-particle methods), the proposed PFEM not only has very good accuracy, but also poses very mild restrictions on the numerical stability, and thus it has significant advantages for solving this type of open curve evolution problems with applications in the simulation of solid-state dewetting. Extensive numerical results are reported to demonstrate the accuracy and high efficiency of the proposed PFEM.

Expanded interleaved solid-state memory for a wide bandwidth transient waveform recorder

NASA Technical Reports Server (NTRS)

Thomas, R. M., Jr.

1980-01-01

An interleaved, solid state expanded memory for a 100 MHz bandwidth waveform recorder is described. The memory development resulted in a significant increase in the storage capacity of a commercially available recorder. The motivation for the memory expansion of the waveform recorder, which is used to support in-flight measurement of the electromagnetic characteristics of lightning discharges, was the need for a significantly longer data window than that provided by the commercially available unit. The expanded recorder provides a data window that is 128 times longer than the commercial unit, while maintaining the same time resolution, by increasing the storage capacity from 1024 to 131 072 data samples. The expanded unit operates at sample periods as small as 10 ns. Sampling once every 10 ns, the commercial unit records for about 10 microseconds before the memory is filled, whereas, the expanded unit records for about 1300 microseconds. A photo of the expanded waveform recorder is shown.

Anomalous radon emission as precursor of medium to strong earthquakes

NASA Astrophysics Data System (ADS)

Zoran, Maria

2016-03-01

Anomalous radon (Rn222) emissions enhanced by forthcoming earthquakes is considered to be a precursory phenomenon related to an increased geotectonic activity in seismic areas. Rock microfracturing in the Earth's crust preceding a seismic rupture may cause local surface deformation fields, rock dislocations, charged particle generation and motion, electrical conductivity changes, radon and other gases emission, fluid diffusion, electrokinetic, piezomagnetic and piezoelectric effects as well as climate fluctuations. Space-time anomalies of radon gas emitted in underground water, soil and near the ground air weeks to days in the epicentral areas can be associated with the strain stress changes that occurred before the occurrence of medium and strong earthquakes. This paper aims to investigate temporal variations of radon concentration levels in air near or in the ground by the use of solid state nuclear track detectors (SSNTD) CR-39 and LR-115 in relation with some important seismic events recorded in Vrancea region, Romania.

Tracking brain states under general anesthesia by using global coherence analysis

PubMed Central

Cimenser, Aylin; Purdon, Patrick L.; Pierce, Eric T.; Walsh, John L.; Salazar-Gomez, Andres F.; Harrell, Priscilla G.; Tavares-Stoeckel, Casie; Habeeb, Kathleen; Brown, Emery N.

2011-01-01

Time and frequency domain analyses of scalp EEG recordings are widely used to track changes in brain states under general anesthesia. Although these analyses have suggested that different spatial patterns are associated with changes in the state of general anesthesia, the extent to which these patterns are spatially coordinated has not been systematically characterized. Global coherence, the ratio of the largest eigenvalue to the sum of the eigenvalues of the cross-spectral matrix at a given frequency and time, has been used to analyze the spatiotemporal dynamics of multivariate time-series. Using 64-lead EEG recorded from human subjects receiving computer-controlled infusions of the anesthetic propofol, we used surface Laplacian referencing combined with spectral and global coherence analyses to track the spatiotemporal dynamics of the brain's anesthetic state. During unconsciousness the spectrograms in the frontal leads showed increasing α (8–12 Hz) and δ power (0–4 Hz) and in the occipital leads δ power greater than α power. The global coherence detected strong coordinated α activity in the occipital leads in the awake state that shifted to the frontal leads during unconsciousness. It revealed a lack of coordinated δ activity during both the awake and unconscious states. Although strong frontal power during general anesthesia-induced unconsciousness—termed anteriorization—is well known, its possible association with strong α range global coherence suggests highly coordinated spatial activity. Our findings suggest that combined spectral and global coherence analyses may offer a new approach to tracking brain states under general anesthesia. PMID:21555565

Single-Specimen Technique to Establish the J-Resistance of Linear Viscoelastic Solids with Constant Poisson's Ratio

NASA Technical Reports Server (NTRS)

Gutierrez-Lemini, Danton; McCool, Alex (Technical Monitor)

2001-01-01

A method is developed to establish the J-resistance function for an isotropic linear viscoelastic solid of constant Poisson's ratio using the single-specimen technique with constant-rate test data. The method is based on the fact that, for a test specimen of fixed crack size under constant rate, the initiation J-integral may be established from the crack size itself, the actual external load and load-point displacement at growth initiation, and the relaxation modulus of the viscoelastic solid, without knowledge of the complete test record. Since crack size alone, of the required data, would be unknown at each point of the load-vs-load-point displacement curve of a single-specimen test, an expression is derived to estimate it. With it, the physical J-integral at each point of the test record may be established. Because of its basis on single-specimen testing, not only does the method not require the use of multiple specimens with differing initial crack sizes, but avoids the need for tracking crack growth as well.

Novel Insight for Organic Matter Sourcing: Interest of Time Resolved Fluorescence to Qualify and Quantify PAH Content of Solid Matrix at High Resolution

NASA Astrophysics Data System (ADS)

Quiers, M.; Perrette, Y.; Jacq, K.; Pousset, E.; Plassart, G.

2017-12-01

OM fluorescence is today a well-developed tool used to characterize and quantify organic matter (OM), but also to evaluate and discriminate OM fate and changes related to climate and environmental modifications. While fluorescence measurements on water and soils extracts provide information about organic fluxes today, solid phase fluorescence using natural archives allows to obtain high resolution records of OM evolution during time. These evolutions can be discussed in regards of climate and environmental perturbations detected in archives using different proxies, and thus provide keys for understanding factors driving carbon fluxes mechanisms. Among fluorescent organic species, Polycyclic Aromatic Hydrocarbons (PAH) have been used as probe molecules for organic contamination tracking. Moreover, monitoring studies have shown that PAH could also be used as markers to discriminates atmospheric and erosion factors leading to PAH and organic matter fluxes to the aquifer. PAH records in soils and natural archives appear as a promising proxy to follow both past atmospheric contamination and soil erosion. But, PAH fluorescence is difficult to discriminate from bulk OM fluorescence using steady-state fluorescence (SSF) technics as their fluorescence domains recover. Time resolved emission spectroscopy (TRES) increases the information provided by SSF technic, adding a time dimension to measurements and allowing to discriminate PAH fluorescence. We report here a first application of this technic on natural archives. The challenge is to obtain TRES signature along the sample, including for low PAH concentrations. This study aims to evaluate the reliability of high resolution TRES measurement as PAH carbon fluxes sources. Method is based on LIF instrument for solid phase fluorescence measurement. An instrument coupling an excitation system constituting by 2 pulsed lasers (266 and 355 nm) and a detection system was developed. This measurement provides high resolution record of PAH fluorescence. Preliminary results on stalagmite samples, lake sediments and soils will be reported. PAH content variations along the sample were compared with PAH concentration and with bulk OM content deduced from SSF records. The accuracy of the PAH fluorescence as source marker of fluxes will be discussed for each type of sample.

Dynamics of Re(2,2'-bipyridine)(CO)3Cl MLCT formation and decay after picosecond pulsed X-ray excitation and femtosecond UV excitation.

PubMed

Zhao, Liyan; Odaka, Hideho; Ono, Hiroshi; Kajimoto, Shinji; Hatanaka, Koji; Hobley, Jonathan; Fukumura, Hiroshi

2005-01-01

The dynamics of Re(2,2'-bipyridine)(CO)3Cl MLCT state formation and decay were determined after femtosecond UV laser excitation and picosecond pulsed X-ray excitation, in an N,N-dimethylformamide (DMF) solution as well as in its solid form. At room temperature, after UV excitation, this MLCT excited state emits both in DMF solution and in the solid form. Transient absorption spectra were measured in solution at various delay times following excitation by a 160 fs, 390 nm laser pulse. There was a prompt absorption increase at around 460 nm occurring within the pump probe convolution (<1 ps), which was assigned to the formation of the 3MLCT state. This transient absorbance was constant over 100 ps. In contrast to the solution state, in the solid state, the emission maximum slightly red-shifts with increasing time after laser excitation. In both solid and solution the emission rises within the system response time. The solid sample exhibited a 1.4 ns emission decay that was not observed for the solution sample. The emission rise from a solid sample after 20 ps pulsed X-ray excitation was significantly slower than the system's time resolution. It is proposed that kinetically energetic electrons are ejected following X-ray induced ionisation, creating ionised tracks in which energetic cations and electrons take time to recombine yielding delayed 3MLCT states that emit.

Investigation of a solid state power combining antenna proposed for use in the solar power satellite

NASA Technical Reports Server (NTRS)

Farmer, L. A.

1981-01-01

Performance tests performed on a four-feed microstrip antenna and feed network are analyzed. Frequency response with and without amplifiers, an investigation of noise threshold, phase tracking, and jitter are included. Recommendations for further development of SPS power conversion modules are also included.

40 CFR 96.253 - Recordation of CAIR SO2 allowances.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Recordation of CAIR SO2 allowances. 96... (CONTINUED) NOX BUDGET TRADING PROGRAM AND CAIR NOX AND SO2 TRADING PROGRAMS FOR STATE IMPLEMENTATION PLANS CAIR SO2 Allowance Tracking System § 96.253 Recordation of CAIR SO2 allowances. (a)(1) After a...

The probability of occurrence of high-loss windstorms

NASA Astrophysics Data System (ADS)

Massey, Neil

2016-04-01

Windstorms are one of the largest meteorological risks to life and property in Europe. High - loss windstorms, in terms of insured losses, are a result of not only the windspeed of the storm but also the position and track of the storm. The two highest loss storms on record, Daria (1990) and Lothar (1999) caused so much damage because they tracked across highly populated areas of Europe. Although the frequency and intensity of high - loss wind storms in the observed record is known, there are not enough samples, due to the short observed record, to truly know the distribution of the frequency and intensity of windstorms over Europe and, by extension, the distribution of losses which could occur if the atmosphere had been in a different state due to the internal variability of the atmosphere. Risk and loss modelling exercises carried out by and for the reinsurance industry have typically stochastically perturbed the historical record of high - loss windstorms to produce distributions of potential windstorms with greater sample sizes than the observations. This poster presents a new method of generating many samples of potential windstorms and analyses the frequency of occurrence, intensity and potential losses of these windstorms. The large ensemble regional climate modelling project weather@home is used to generate many regional climate model representations (800 per year) of the weather over Europe between 1985 and 2010. The regional climate model is driven at the boundaries by a free running global climate model and so each ensemble member represents a potential state of the atmosphere, rather than an observed state. The winter storm season of October to March is analysed by applying an objective cyclone identification and tracking algorithm to each ensemble member. From the resulting tracks, the windspeed within a 1000km radius of the cyclone centre is extracted and the maximum windspeed over a 72 hour period is derived as the storm windspeed footprint. This footprint is fed into a population based loss model to estimate the losses for the storm. Additionally the same analysis is performed on data from the same regional climate model, driven at the boundaries by ERA - Interim. This allows the tracks and losses of the storms in the observed record to be recovered using the same tracking method and loss model. A storm track matching function is applied to the storm tracks in the large ensemble and so analogues of the observed storms can be recovered. The frequency of occurrence of the high - loss storms in the large ensemble can then be determined, and used as a proxy for the frequency of occurrence in the observations.

3D imaging of neutron tracks using confocal microscopy

NASA Astrophysics Data System (ADS)

Gillmore, Gavin; Wertheim, David; Flowers, Alan

2016-04-01

Neutron detection and neutron flux assessment are important aspects in monitoring nuclear energy production. Neutron flux measurements can also provide information on potential biological damage from exposure. In addition to the applications for neutron measurement in nuclear energy, neutron detection has been proposed as a method of enhancing neutrino detectors and cosmic ray flux has also been assessed using ground-level neutron detectors. Solid State Nuclear Track Detectors (or SSNTDs) have been used extensively to examine cosmic rays, long-lived radioactive elements, radon concentrations in buildings and the age of geological samples. Passive SSNTDs consisting of a CR-39 plastic are commonly used to measure radon because they respond to incident charged particles such as alpha particles from radon gas in air. They have a large dynamic range and a linear flux response. We have previously applied confocal microscopy to obtain 3D images of alpha particle tracks in SSNTDs from radon track monitoring (1). As a charged particle traverses through the polymer it creates an ionisation trail along its path. The trail or track is normally enhanced by chemical etching to better expose radiation damage, as the damaged area is more sensitive to the etchant than the bulk material. Particle tracks in CR-39 are usually assessed using 2D optical microscopy. In this study 6 detectors were examined using an Olympus OLS4100 LEXT 3D laser scanning confocal microscope (Olympus Corporation, Japan). The detectors had been etched for 2 hours 50 minutes at 85 °C in 6.25M NaOH. Post etch the plastics had been treated with a 10 minute immersion in a 2% acetic acid stop bath, followed by rinsing in deionised water. The detectors examined had been irradiated with a 2mSv neutron dose from an Am(Be) neutron source (producing roughly 20 tracks per mm2). We were able to successfully acquire 3D images of neutron tracks in the detectors studied. The range of track diameter observed was between 4 and 10 microns. Thus this study suggests that, using confocal microscopy, 3D imaging of neutron tracks in SSNTDs is feasible. (1) Wertheim D, Gillmore G, Brown L, Petford N. A new method of imaging particle tracks in solid state nuclear track detectors. J Microsc. 2010; 237: 1-6.

Retool State-to-District Intervention for Better Outcomes

ERIC Educational Resources Information Center

Slotnik, William J.

2014-01-01

The national track record for state-to-district assistance is not stellar. It is tactics in the absence of strategy and activities in the absence of accomplishment. The problem is systemic: State departments need to transform their organizational structures to facilitate rather than hinder effective assistance strategies. The starting place is…

Optical microwell assay of membrane transport kinetics.

PubMed

Kiskin, Nikolai I; Siebrasse, Jan P; Peters, Reiner

2003-10-01

In optical single transporter recording, membranes are firmly attached to flat solid substrates containing small wells or test compartments (TC). Transport of fluorescent molecules through TC-spanning membrane patches is induced by solution change and recorded by confocal microscopy. Previously, track-etched membrane filters were used to create solid substrates containing populations of randomly distributed TCs. In this study the possibilities offered by orderly TC arrays as created by laser microdrilling were explored. A theoretical framework was developed taking the convolution of membrane transport, solution change, and diffusion into account. The optical properties of orderly TC arrays were studied and the kinetics of solution change measured. Export and import through the nuclear pore complex (NPC) was analyzed in isolated envelopes of Xenopus oocyte nuclei. In accordance with previous reports nuclear transport receptor NTF2, which binds directly to NPC proteins, was found to be translocated much faster than "inert" molecules of similar size. Unexpectedly, NXT1, a homolog of NTF2 reportedly unable to bind to NPC proteins directly, was translocated as fast as NTF2. Thus, microstructured TC arrays were shown to provide optical single transporter recording with a new basis.

Proton induced target fragmentation studies on solid state nuclear track detectors using Carbon radiators

NASA Astrophysics Data System (ADS)

Szabó, J.; Pálfalvi, J. K.; Strádi, A.; Bilski, P.; Swakoń, J.; Stolarczyk, L.

2018-04-01

One of the limiting factors of an astronaut's career is the dose received from space radiation. High energy protons, being the main components of the complex radiation field present on a spacecraft, give a significant contribution to the dose. To investigate the behavior of solid state nuclear track detectors (SSNTDs) if they are irradiated by such particles, SSNTD stacks containing carbon blocks were exposed to high energy proton beams (70, 100, 150 and 230 MeV) at the Proteus cyclotron, IFJ PAN -Krakow. The incident protons cannot be detected directly; however, tracks of secondary particles, recoils and fragments of the constituent atoms of the detector material and of the carbon radiator are formed. It was found that as the proton energy increases, the number of tracks induced in the PADC material by secondary particles decreases. From the measured geometrical parameters of the tracks the linear energy transfer (LET) spectrum and the dosimetric quantities were determined, applying appropriate calibration. In the LET spectra the LET range of the most important secondary particles could be identified and their abundance showed differences in the spectra if the detectors were short or long etched. The LET spectra obtained on the SSNTDs irradiated by protons were compared to LET spectra of detectors flown on the International Space Station (ISS): they were quite similar, resulting in a quality factor difference of only 5%. Thermoluminescent detectors (TLDs) were applied in each case to measure the dose from primary protons and other lower LET particles present in space. Comparing and analyzing the results of the TLD and SSNTD measurements, it was obtained that proton induced target fragments contributed to the total absorbed dose in 3.2% and to the dose equivalent in 14.2% in this particular space experiment.

Optimum municipal solid waste collection using geographical information system (GIS) and vehicle tracking for Pallavapuram municipality.

PubMed

Kanchanabhan, T E; Abbas Mohaideen, J; Srinivasan, S; Sundaram, V Lenin Kalyana

2011-03-01

Waste collection and transportation is the contact point between waste generators and waste management systems. A proposal for an innovative model for the collection and transportation of municipal solid waste (MSW) which is a part of a solid waste management system using a spatial geo database, integrated in a geographical information system (GIS) environment is presented. Pallavapuram is a fast-developing municipality of Chennai city in the southern suburbs about 20 km from Chennai, the state capital of Tamil Nadu in India. The disposal of MSW was previously occurring in an indiscriminate and irrational manner in the municipality. Hence in the present study an attempt was made to develop an engineered design of solid waste collection using GIS with a vehicle tracking system and final disposal by composting with investment costs. The GIS was used to analyse existing maps and data, to digitize the existing ward boundaries and to enter data about the wards and disposal sites. The proposed GIS model for solid waste disposal would give information on the planning of bins, vehicles and the optimal route. In the case of disposal, composting would be a successful strategy to accelerate the decomposition and stabilization of the biodegradable components of waste in MSW.

Measurement of Isobaric Analogue Resonances of 47Ar with the Active-Target Time Projection Chamber

NASA Astrophysics Data System (ADS)

Bradt, Joshua William

While the nuclear shell model accurately describes the structure of nuclei near stability, the structure of unstable, neutron-rich nuclei is still an area of active research. One region of interest is the set of nuclei near N=28. The shell model suggests that these nuclei should be approximately spherical due to the shell gap predicted by their magic number of neutrons; however, experiments have shown that the nuclei in this region rapidly become deformed as protons are removed from the spherical 48Ca. This makes 46Ar a particularly interesting system as it lies in a transition region between 48Ca and lighter isotones that are known to be deformed. An experiment was performed at the National Superconducting Cyclotron Laboratory (NSCL) to measure resonant proton scattering on 46Ar. The resonances observed in this reaction correspond to unbound levels in the 47K intermediate state nucleus which are isobaric analogues of states in the 47Ar nucleus. By measuring the spectroscopic factors of these states in 47Ar, we gain information about the single-particle structure of this system, which is directly related to the size of the N=28 shell gap. Four resonances were observed: one corresponding to the ground state in 47Ar, one corresponding its first excited 1/2- state, and two corresponding to 1/2+ states in either 47Ar or the intermediate state nucleus. However, only a limited amount of information about these states could be recovered due to the low experimental statistics and limited angular resolution caused by pileup rejection and the inability to accurately reconstruct the beam particle track. In addition to the nuclear physics motivations, this experiment served as the radioactive beam commissioning for the Active-Target Time Projection Chamber (AT-TPC). The AT-TPC is a new gas-filled charged particle detector built at the NSCL to measure low-energy radioactive beams from the ReA3 facility. Since the gas inside the detector serves as both the tracking medium and the scattering target, reactions are measured over a continuous range of energies with near-4π solid angle coverage. This experiment demonstrated that tracks recorded by the AT-TPC can be reconstructed to a good resolution, and it established the feasibility of performing similar experiments with this detector in the future.

Dosimetry in radiobiological studies with the heavy ion beam of the Warsaw cyclotron

NASA Astrophysics Data System (ADS)

Kaźmierczak, U.; Banaś, D.; Braziewicz, J.; Czub, J.; Jaskóła, M.; Korman, A.; Kruszewski, M.; Lankoff, A.; Lisowska, H.; Malinowska, A.; Stępkowski, T.; Szefliński, Z.; Wojewódzka, M.

2015-12-01

The aim of this study was to verify various dosimetry methods in the irradiation of biological materials with a 12C ion beam at the Heavy Ion Laboratory of the University of Warsaw. To this end the number of ions hitting the cell nucleus, calculated on the basis of the Si-detector system used in the set-up, was compared with the number of ion tracks counted in irradiated Solid State Nuclear Track Detectors and with the number of ion tracks detected in irradiated Chinese Hamster Ovary cells processed for the γ-H2AX assay. Tests results were self-consistent and confirmed that the system serves its dosimetric purpose.

Indoor concentration of radon, thoron and their progeny around granite regions in the state of Karnataka, India.

PubMed

Sannappa, J; Ningappa, C

2014-03-01

An extensive studies on the indoor activity concentrations of thoron, radon and their progeny in the granite region in the state of Karnataka, India, has been carried out since, 2007 in the scope of a lung cancer epidemiological study using solid-state nuclear track detector-based double-chamber dosemeters (LR-115, type II plastic track detector). Seventy-four dwellings of different types were selected for the measurement. The dosemeters containing SSNTD detectors were fixed 2 m above the floor. After an exposure time of 3 months (90 d), films were etched to reveal tracks. From the track density, the concentrations of radon and thoron were evaluated. The value of the indoor concentration of thoron and radon in the study area varies from 16 to 170 Bq m(-3) and 18 to 300 Bq m(-3) with medians of 66 and 82.3 Bq m(-3), respectively, and that of their progeny varies from 1.8 to 24 mWL with a median of 3.6 mWL and 1.6 to 19.6 mWL, respectively. The concentrations of indoor thoron, radon and their progeny and their equivalent effective doses are discussed.

Complete tomography of a high-fidelity solid-state entangled spin-photon qubit pair.

PubMed

De Greve, Kristiaan; McMahon, Peter L; Yu, Leo; Pelc, Jason S; Jones, Cody; Natarajan, Chandra M; Kim, Na Young; Abe, Eisuke; Maier, Sebastian; Schneider, Christian; Kamp, Martin; Höfling, Sven; Hadfield, Robert H; Forchel, Alfred; Fejer, M M; Yamamoto, Yoshihisa

2013-01-01

Entanglement between stationary quantum memories and photonic qubits is crucial for future quantum communication networks. Although high-fidelity spin-photon entanglement was demonstrated in well-isolated atomic and ionic systems, in the solid-state, where massively parallel, scalable networks are most realistically conceivable, entanglement fidelities are typically limited due to intrinsic environmental interactions. Distilling high-fidelity entangled pairs from lower-fidelity precursors can act as a remedy, but the required overhead scales unfavourably with the initial entanglement fidelity. With spin-photon entanglement as a crucial building block for entangling quantum network nodes, obtaining high-fidelity entangled pairs becomes imperative for practical realization of such networks. Here we report the first results of complete state tomography of a solid-state spin-photon-polarization-entangled qubit pair, using a single electron-charged indium arsenide quantum dot. We demonstrate record-high fidelity in the solid-state of well over 90%, and the first (99.9%-confidence) achievement of a fidelity that will unambiguously allow for entanglement distribution in solid-state quantum repeater networks.

Calibration of solid state nuclear track detectors at high energy ion beams for cosmic radiation measurements: HAMLET results

NASA Astrophysics Data System (ADS)

Szabó, J.; Pálfalvi, J. K.

2012-12-01

The MATROSHKA experiments and the related HAMLET project funded by the European Commission aimed to study the dose burden of the crew working on the International Space Station (ISS). During these experiments a human phantom equipped with several thousands of radiation detectors was exposed to cosmic rays inside and outside the ISS. Besides the measurements realized in Earth orbit, the HAMLET project included also a ground-based program of calibration and intercomparison of the different detectors applied by the participating groups using high-energy ion beams. The Space Dosimetry Group of the Centre for Energy Research (formerly Atomic Energy Research Institute) participated in these experiments with passive solid state nuclear track detectors (SSNTDs). The paper presents the results of the calibration experiments performed in the years 2008-2011 at the Heavy Ion Medical Accelerator (HIMAC) of the National Institute of Radiological Sciences (NIRS), Chiba, Japan. The data obtained serve as update and improvement for the previous calibration curves which are necessary for the evaluation of the SSNTDs exposed in unknown space radiation fields.

Bounding the Effects of Social Experiments: Accounting for Attrition in Administrative Data

ERIC Educational Resources Information Center

Grogger, Jeffrey

2012-01-01

Background: Social experiments frequently exploit data from administrative records. However, most administrative data systems are designed to track earnings or benefit payments among residents within a single state. When an experimental participant moves across state lines, his entries in the data system of his state of origin consist entirely of…

3D imaging of particle tracks in Solid State Nuclear Track Detectors

NASA Astrophysics Data System (ADS)

Wertheim, D.; Gillmore, G.; Brown, L.; Petford, N.

2009-04-01

Inhalation of radon gas (222Rn) and associated ionizing decay products is known to cause lung cancer in human. In the U.K., it has been suggested that 3 to 5 % of total lung cancer deaths can be linked to elevated radon concentrations in the home and/or workplace. Radon monitoring in buildings is therefore routinely undertaken in areas of known risk. Indeed, some organisations such as the Radon Council in the UK and the Environmental Protection Agency in the USA, advocate a ‘to test is best' policy. Radon gas occurs naturally, emanating from the decay of 238U in rock and soils. Its concentration can be measured using CR?39 plastic detectors which conventionally are assessed by 2D image analysis of the surface; however there can be some variation in outcomes / readings even in closely spaced detectors. A number of radon measurement methods are currently in use (for examples, activated carbon and electrets) but the most widely used are CR?39 solid state nuclear track?etch detectors (SSNTDs). In this technique, heavily ionizing alpha particles leave tracks in the form of radiation damage (via interaction between alpha particles and the atoms making up the CR?39 polymer). 3D imaging of the tracks has the potential to provide information relating to angle and energy of alpha particles but this could be time consuming. Here we describe a new method for rapid high resolution 3D imaging of SSNTDs. A ‘LEXT' OLS3100 confocal laser scanning microscope was used in confocal mode to successfully obtain 3D image data on four CR?39 plastic detectors. 3D visualisation and image analysis enabled characterisation of track features. This method may provide a means of rapid and detailed 3D analysis of SSNTDs. Keywords: Radon; SSNTDs; confocal laser scanning microscope; 3D imaging; LEXT

(13)C and (15)N solid-state NMR studies on albendazole and cyclodextrin albendazole complexes.

PubMed

Ferreira, M João G; García, A; Leonardi, D; Salomon, Claudio J; Lamas, M Celina; Nunes, Teresa G

2015-06-05

(13)C and (15)N solid-state nuclear magnetic resonance (NMR) spectra were recorded from albendazole (ABZ) and from ABZ:β-cyclodextrin, ABZ:methyl-β-cyclodextrin, ABZ:hydroxypropyl-β-cyclodextrin and ABZ:citrate-β-cyclodextrin, which were prepared by the spray-drying technique. ABZ signals were typical of a crystalline solid for the pure drug and of an amorphous compound obtained from ABZ:cyclodextrin samples. Relevant spectral differences were correlated with chemical interaction between ABZ and cyclodextrins. The number and type of complexes revealed a strong dependence on the cyclodextrin group substituent. Solid-state NMR data were consistent with the presence of stable inclusion complexes. Copyright © 2015 Elsevier Ltd. All rights reserved.

A solid-state digital temperature recorder for space use

NASA Technical Reports Server (NTRS)

Westbrook, R. M.; Bennett, L. D.; Steinhaver, R. A.; Deboo, G. J.

1981-01-01

A solid-state, digital, temperature recorder has been developed for use in space experiments. The recorder is completely self-contained and includes a temperature sensor; all necessary electronics for signal conditioning, processing, storing, control and timing; and a battery power supply. No electrical interfacing with the particular spacecraft on which the unit is used is required. The recorder is small, light, and sturdy, and has no moving parts. It uses only biocompatible materials and has passed vibration and shock spaceflight qualification tests. The unit is capable of storing 2048, -10 to +45 C, 8-bit temperature measurements taken at intervals selectable by factors of 2 from 1.875 to 240 min; data can be retained for at least 6 months. The basic recorder can be simplified to accommodate a variety of applications by adding memory to allow more data to be recorded, by changing the front end to permit measurements other than temperature to be made, and by using different batteries to realize various operating periods. Stored flight data are read out from the recorder by means of a ground read-out unit.

Tackling Production Techniques: Professional Studio Sound at Amateur Prices: the Power of the Portable Four-Track Audio Recorder.

ERIC Educational Resources Information Center

Robinson, David E.

1997-01-01

One solution to poor quality sound in student video projects is a four-track audio cassette recorder. This article discusses the advantages of four-track over single-track recorders and compares two student productions, one using a single-track and the other a four-track recorder. (PEN)

Optimal reproducibility of gated sestamibi and thallium myocardial perfusion study left ventricular ejection fractions obtained on a solid-state CZT cardiac camera requires operator input.

PubMed

Cherk, Martin H; Ky, Jason; Yap, Kenneth S K; Campbell, Patrina; McGrath, Catherine; Bailey, Michael; Kalff, Victor

2012-08-01

To evaluate the reproducibility of serial re-acquisitions of gated Tl-201 and Tc-99m sestamibi left ventricular ejection fraction (LVEF) measurements obtained on a new generation solid-state cardiac camera system during myocardial perfusion imaging and the importance of manual operator optimization of left ventricular wall tracking. Resting blinded automated (auto) and manual operator optimized (opt) LVEF measurements were measured using ECT toolbox (ECT) and Cedars-Sinai QGS software in two separate cohorts of 55 Tc-99m sestamibi (MIBI) and 50 thallium (Tl-201) myocardial perfusion studies (MPS) acquired in both supine and prone positions on a cadmium zinc telluride (CZT) solid-state camera system. Resting supine and prone automated LVEF measurements were similarly obtained in a further separate cohort of 52 gated cardiac blood pool scans (GCBPS) for validation of methodology and comparison. Appropriate use of Bland-Altman, chi-squared and Levene's equality of variance tests was used to analyse the resultant data comparisons. For all radiotracer and software combinations, manual checking and optimization of valve planes (+/- centre radius with ECT software) resulted in significant improvement in MPS LVEF reproducibility that approached that of planar GCBPS. No difference was demonstrated between optimized MIBI/Tl-201 QGS and planar GCBPS LVEF reproducibility (P = .17 and P = .48, respectively). ECT required significantly more manual optimization compared to QGS software in both supine and prone positions independent of radiotracer used (P < .02). Reproducibility of gated sestamibi and Tl-201 LVEF measurements obtained during myocardial perfusion imaging with ECT toolbox or QGS software packages using a new generation solid-state cardiac camera with improved image quality approaches that of planar GCBPS however requires visual quality control and operator optimization of left ventricular wall tracking for best results. Using this superior cardiac technology, Tl-201 reproducibility also appears at least equivalent to sestamibi for measuring LVEF.

13C CP MAS NMR and GIAO-CHF calculations of coumarins.

PubMed

Zolek, Teresa; Paradowska, Katarzyna; Wawer, Iwona

2003-01-01

13C cross-polarization magic-angle spinning NMR spectra were recorded for a series of solid coumarins. Ab initio calculations of shielding constants were performed with the use of GIAO-CHF method. The combined CPMAS NMR and theoretical approach was successful in characterizing solid-state conformations of coumarins; a relationship sigma (ppm) = -1.032 xdelta + 205.28 (R(2) = 0.9845) can be used to obtain structural information for coumarins, for which solid-state NMR or crystal structure data are not available. Copyright 2002 Elsevier Science (USA)

Lessons learned: from dye-sensitized solar cells to all-solid-state hybrid devices.

PubMed

Docampo, Pablo; Guldin, Stefan; Leijtens, Tomas; Noel, Nakita K; Steiner, Ullrich; Snaith, Henry J

2014-06-25

The field of solution-processed photovoltaic cells is currently in its second spring. The dye-sensitized solar cell is a widely studied and longstanding candidate for future energy generation. Recently, inorganic absorber-based devices have reached new record efficiencies, with the benefits of all-solid-state devices. In this rapidly changing environment, this review sheds light on recent developments in all-solid-state solar cells in terms of electrode architecture, alternative sensitizers, and hole-transporting materials. These concepts are of general applicability to many next-generation device platforms. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Electronic Timekeeping: North Dakota State University Improves Payroll Processing.

ERIC Educational Resources Information Center

Vetter, Ronald J.; And Others

1993-01-01

North Dakota State University has adopted automated timekeeping to improve the efficiency and effectiveness of payroll processing. The microcomputer-based system accurately records and computes employee time, tracks labor distribution, accommodates complex labor policies and company pay practices, provides automatic data processing and reporting,…

Multiple-hypothesis multiple-model line tracking

NASA Astrophysics Data System (ADS)

Pace, Donald W.; Owen, Mark W.; Cox, Henry

2000-07-01

Passive sonar signal processing generally includes tracking of narrowband and/or broadband signature components observed on a Lofargram or on a Bearing-Time-Record (BTR) display. Fielded line tracking approaches to date have been recursive and single-hypthesis-oriented Kalman- or alpha-beta filters, with no mechanism for considering tracking alternatives beyond the most recent scan of measurements. While adaptivity is often built into the filter to handle changing track dynamics, these approaches are still extensions of single target tracking solutions to multiple target tracking environment. This paper describes an application of multiple-hypothesis, multiple target tracking technology to the sonar line tracking problem. A Multiple Hypothesis Line Tracker (MHLT) is developed which retains the recursive minimum-mean-square-error tracking behavior of a Kalman Filter in a maximum-a-posteriori delayed-decision multiple hypothesis context. Multiple line track filter states are developed and maintained using the interacting multiple model (IMM) state representation. Further, the data association and assignment problem is enhanced by considering line attribute information (line bandwidth and SNR) in addition to beam/bearing and frequency fit. MHLT results on real sonar data are presented to demonstrate the benefits of the multiple hypothesis approach. The utility of the system in cluttered environments and particularly in crossing line situations is shown.

Efficiently reducing transition curvature in heat-assisted magnetic recording with state-of-the-art write heads

NASA Astrophysics Data System (ADS)

Vogler, Christoph; Abert, Claas; Bruckner, Florian; Suess, Dieter

2017-05-01

Curvatures of bit transitions on granular media are a serious problem for the read-back process. We address this fundamental issue and propose a possibility to efficiently reduce transition curvatures with state-of-the-art heat-assisted magnetic recording heads. We compare footprints of conventional with those of the proposed head design on different media, consisting of exchange coupled and single phase grains. Additionally, we investigate the impact of various recording parameters, such as the full width at half maximum (FWHM) of the applied heat pulse and the coercivity gradient near the write temperature of the recording grains. The footprints are calculated with a coarse grained model, based on the Landau-Lifshitz-Bloch equation. The presented simulations show a transition curvature reduction of up to 40%, in the case of a medium with exchange coupled grains and a heat pulse with a FWHM of 40 nm. We further give the reason for the straightening of the bit transitions, by means of basic considerations with regard to the effective recording time window of the write process. Besides the transition curvature reduction, the proposed head design yields an improvement of the transition jitter in both down-track and off-track directions.

A Quasi-Solid-State Sodium-Ion Capacitor with High Energy Density.

PubMed

Wang, Faxing; Wang, Xiaowei; Chang, Zheng; Wu, Xiongwei; Liu, Xiang; Fu, Lijun; Zhu, Yusong; Wu, Yuping; Huang, Wei

2015-11-18

A quasi-solid-state sodium-ion capacitor is demonstrated with nanoporous disordered carbon and macroporous graphene as the negative and positive electrodes, respectively, using a sodium-ion-conducting gel polymer electrolyte. It can operate at a cell voltage as high as 4.2 V with an energy density of record high 168 W h kg(-1). © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Revisiting the thermal-spike concept in ion-surface interactions

NASA Astrophysics Data System (ADS)

Miotello, Antonio; Kelly, Roger

1997-02-01

In recent years many groups have advocated a thermal-spike model to explain a variety of experimental results in ion-irradiation of solids, as for example sputtering, mixing, compositional change, structural change, and track formation. The latter include crystal-to-amorphous transitions as well as track formation due to MeV/u particles. In this paper we reconsider the phenomena occurring during ion impact of solids looking at the time scale generally indicated as relevant for thermal-spike effects, namely a picosecond scale as shown by molecular dynamics. Sputtering, mixing, and track formation, however, will be analyzed in more detail. We consider first ion-beam sputtering and reiterate (as is already well-known) that yields which increase with the bulk temperature most often indicate merely the onset of normal vaporization. Indeed, only simulations appear to be capable of giving insight even if the information is sometimes tentative. In mixing, ballistic transport is important but not dominant. It is often argued that the additional transport is provided by thermal spikes but it is noted that such an assumption is normally not required by the experimental results. What is more relevant is a role for residual defects such that the total diffusion flux includes (if the defects are chemically guided) a modified Darken factor, or (if the defects are not chemically guided) simply an increased diffusivity. The time scale (min), distances (well beyond the collision cascade), temperature sensitivity (changes of as little as 75 K are relevant), and correlation with vacancy properties (thence with the solid rather than liquid state) which are relevant to these residual defects are not understandable in terms of thermal spikes. We finally consider track formation. Recent work claiming that track formation in solids, irradiated with heavy ions, may be understood in terms of thermal spikes is reconsidered to show that the thermal-spike model is utilized without considering all the relevant phenomena included in irradiation-induced heating and phase transitions. For example, a comparison of fs-laser pulse irradiation of Si with swift heavy-ion irradiation, shows that melting is possible in the first case since the excited electrons have a low and more or less restricted energy while in the case of swift ion-irradiation, the motion of the excited electrons includes a ballistic component which does not favour the localization of the thermal energy necessary to induce lattice melting. It is concluded that track formation is better understandable in a more general framework of defect-induced processes in solids.

Astrobiology: An astronomer's perspective

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bergin, Edwin A.

2014-12-08

In this review we explore aspects of the field of astrobiology from an astronomical viewpoint. We therefore focus on the origin of life in the context of planetary formation, with additional emphasis on tracing the most abundant volatile elements, C, H, O, and N that are used by life on Earth. We first explore the history of life on our planet and outline the current state of our knowledge regarding the delivery of the C, H, O, N elements to the Earth. We then discuss how astronomers track the gaseous and solid molecular carriers of these volatiles throughout the processmore » of star and planet formation. It is now clear that the early stages of star formation fosters the creation of water and simple organic molecules with enrichments of heavy isotopes. These molecules are found as ice coatings on the solid materials that represent microscopic beginnings of terrestrial worlds. Based on the meteoritic and cometary record, the process of planet formation, and the local environment, lead to additional increases in organic complexity. The astronomical connections towards this stage are only now being directly made. Although the exact details are uncertain, it is likely that the birth process of star and planets likely leads to terrestrial worlds being born with abundant water and organics on the surface.« less

Molecularly Engineered Azobenzene Derivatives for High Energy Density Solid-State Solar Thermal Fuels.

PubMed

Cho, Eugene N; Zhitomirsky, David; Han, Grace G D; Liu, Yun; Grossman, Jeffrey C

2017-03-15

Solar thermal fuels (STFs) harvest and store solar energy in a closed cycle system through conformational change of molecules and can release the energy in the form of heat on demand. With the aim of developing tunable and optimized STFs for solid-state applications, we designed three azobenzene derivatives functionalized with bulky aromatic groups (phenyl, biphenyl, and tert-butyl phenyl groups). In contrast to pristine azobenzene, which crystallizes and makes nonuniform films, the bulky azobenzene derivatives formed uniform amorphous films that can be charged and discharged with light and heat for many cycles. Thermal stability of the films, a critical metric for thermally triggerable STFs, was greatly increased by the bulky functionalization (up to 180 °C), and we were able to achieve record high energy density of 135 J/g for solid-state STFs, over a 30% improvement compared to previous solid-state reports. Furthermore, the chargeability in the solid state was improved, up to 80% charged from 40% charged in previous solid-state reports. Our results point toward molecular engineering as an effective method to increase energy storage in STFs, improve chargeability, and improve the thermal stability of the thin film.

The School Superintendency: Male Bastion or Equal Opportunity?

ERIC Educational Resources Information Center

Wolverton, Mimi

1999-01-01

This paper outlines the basic tenets of occupational segregation. It examines Washington State's school labor markets, paying particular attention to where and in what proportions women participate. It questions, based on the state's track record, whether leadership roles in school districts remain male bastions, or whether they offer equal…

High average power diode pumped solid state laser

NASA Astrophysics Data System (ADS)

Gao, Yue; Wang, Yanjie; Chan, Amy; Dawson, Murray; Greene, Ben

2017-03-01

A new generation of high average power pulsed multi-joule solid state laser system has been developed at EOS Space Systems for various space related tracking applications. It is a completely diode pumped, fully automated multi-stage system consisting of a pulsed single longitudinal mode oscillator, three stages of pre-amplifiers, two stages of power amplifiers, completely sealed phase conjugate mirror or stimulated Brillouin scattering (SBS) cell and imaging relay optics with spatial filters in vacuum cells. It is capable of generating pulse energy up to 4.7 J, a beam quality M 2 ~ 3, pulse width between 10-20 ns, and a pulse repetition rate between 100-200 Hz. The system has been in service for more than two years with excellent performance and reliability.

Investigation of the Effect of Small Hardening Spots Created on the Sample Surface by Laser Complex with Solid-State Laser

NASA Astrophysics Data System (ADS)

Nozdrina, O.; Zykov, I.; Melnikov, A.; Tsipilev, V.; Turanov, S.

2018-03-01

This paper describes the results of an investigation of the effect of small hardening spots (about 1 mm) created on the surface of a sample by laser complex with solid-state laser. The melted area of the steel sample is not exceed 5%. Steel microhardness change in the region subjected to laser treatment is studied. Also there is a graph of the deformation of samples dependence on the tension. As a result, the yield plateau and plastic properties changes were detected. The flow line was tracked in the series of speckle photographs. As a result we can see how mm surface inhomogeneity can influence on the deformation and strength properties of steel.

Two-photon excitation of 2,5-diphenyloxazole using a low power green solid state laser

NASA Astrophysics Data System (ADS)

Luchowski, Rafal

2011-01-01

This Letter concerns two-photon excitation of 2,5-diphenyloxazole (PPO) upon illumination from a pulsed 532 nm solid state laser, with an average power of 30 mW, and a repetition rate of 20 MHz. A very agreeable emission spectrum position and shape has been achieved for PPO receiving one- and two-photon excitation, which suggests that the same excited state is involved for both excitation modes. Also, a perfect quadratic dependence of laser power in the emission intensity function has been recorded. We tested the application of a small solid state green laser to two-photon induced time-resolved fluorescence, revealing the emission anisotropy of PPO to be considerably higher for two-photon than for one-photon excitation.

A solid state source of photon triplets based on quantum dot molecules

PubMed Central

Khoshnegar, Milad; Huber, Tobias; Predojević, Ana; Dalacu, Dan; Prilmüller, Maximilian; Lapointe, Jean; Wu, Xiaohua; Tamarat, Philippe; Lounis, Brahim; Poole, Philip; Weihs, Gregor; Majedi, Hamed

2017-01-01

Producing advanced quantum states of light is a priority in quantum information technologies. In this context, experimental realizations of multipartite photon states would enable improved tests of the foundations of quantum mechanics as well as implementations of complex quantum optical networks and protocols. It is favourable to directly generate these states using solid state systems, for simpler handling and the promise of reversible transfer of quantum information between stationary and flying qubits. Here we use the ground states of two optically active coupled quantum dots to directly produce photon triplets. The formation of a triexciton in these ground states leads to a triple cascade recombination and sequential emission of three photons with strong correlations. We record 65.62 photon triplets per minute under continuous-wave pumping, surpassing rates of earlier reported sources. Our structure and data pave the way towards implementing multipartite photon entanglement and multi-qubit readout schemes in solid state devices. PMID:28604705

Anomalous radon emission as precursor of medium to strong earthquakes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zoran, Maria

Anomalous radon (Rn{sup 222}) emissions enhanced by forthcoming earthquakes is considered to be a precursory phenomenon related to an increased geotectonic activity in seismic areas. Rock microfracturing in the Earth’s crust preceding a seismic rupture may cause local surface deformation fields, rock dislocations, charged particle generation and motion, electrical conductivity changes, radon and other gases emission, fluid diffusion, electrokinetic, piezomagnetic and piezoelectric effects as well as climate fluctuations. Space-time anomalies of radon gas emitted in underground water, soil and near the ground air weeks to days in the epicentral areas can be associated with the strain stress changes that occurredmore » before the occurrence of medium and strong earthquakes. This paper aims to investigate temporal variations of radon concentration levels in air near or in the ground by the use of solid state nuclear track detectors (SSNTD) CR-39 and LR-115 in relation with some important seismic events recorded in Vrancea region, Romania.« less

Advances in the Dynallax solid-state dynamic parallax barrier autostereoscopic visualization display system.

PubMed

Peterka, Tom; Kooima, Robert L; Sandin, Daniel J; Johnson, Andrew; Leigh, Jason; DeFanti, Thomas A

2008-01-01

A solid-state dynamic parallax barrier autostereoscopic display mitigates some of the restrictions present in static barrier systems, such as fixed view-distance range, slow response to head movements, and fixed stereo operating mode. By dynamically varying barrier parameters in real time, viewers may move closer to the display and move faster laterally than with a static barrier system, and the display can switch between 3D and 2D modes by disabling the barrier on a per-pixel basis. Moreover, Dynallax can output four independent eye channels when two viewers are present, and both head-tracked viewers receive an independent pair of left-eye and right-eye perspective views based on their position in 3D space. The display device is constructed by using a dual-stacked LCD monitor where a dynamic barrier is rendered on the front display and a modulated virtual environment composed of two or four channels is rendered on the rear display. Dynallax was recently demonstrated in a small-scale head-tracked prototype system. This paper summarizes the concepts presented earlier, extends the discussion of various topics, and presents recent improvements to the system.

Optimal fault-tolerant control strategy of a solid oxide fuel cell system

NASA Astrophysics Data System (ADS)

Wu, Xiaojuan; Gao, Danhui

2017-10-01

For solid oxide fuel cell (SOFC) development, load tracking, heat management, air excess ratio constraint, high efficiency, low cost and fault diagnosis are six key issues. However, no literature studies the control techniques combining optimization and fault diagnosis for the SOFC system. An optimal fault-tolerant control strategy is presented in this paper, which involves four parts: a fault diagnosis module, a switching module, two backup optimizers and a controller loop. The fault diagnosis part is presented to identify the SOFC current fault type, and the switching module is used to select the appropriate backup optimizer based on the diagnosis result. NSGA-II and TOPSIS are employed to design the two backup optimizers under normal and air compressor fault states. PID algorithm is proposed to design the control loop, which includes a power tracking controller, an anode inlet temperature controller, a cathode inlet temperature controller and an air excess ratio controller. The simulation results show the proposed optimal fault-tolerant control method can track the power, temperature and air excess ratio at the desired values, simultaneously achieving the maximum efficiency and the minimum unit cost in the case of SOFC normal and even in the air compressor fault.

Virtual Schools in the U.S. 2013: Politics, Performance, Policy, and Research Evidence

ERIC Educational Resources Information Center

Miron, Gary; Horvitz, Brian; Gulosino, Charisse; Huerta, Luis; Rice, Jennifer King; Shafer, Sheryl Rankin; Cuban, Larry

2013-01-01

This national study, which comprehensively reviews 311 virtual schools operating in the United States, finds serious and systemic problems with the nation's full-time cyber schools. Despite virtual schools' track record of students falling behind their peers academically or dropping-out at higher rates, states and districts continue to expand…

DOE Office of Scientific and Technical Information (OSTI.GOV)

Walker, Randy M; Hill, David E; Gorman, Bryan L

As a proof of concept tested in an operational context, the Global Radiological Source Sorting, Tracking, and Monitoring (GRadSSTraM) Project successfully demonstrated that radio frequency identification (RFID) and Web 2.0* technologies can be deployed to track controlled shipments between the United States and the European Union. Between November 2009 and May 2010, a total of 19 shipments were successfully shipped from Oak Ridge National Laboratory (ORNL) by the U.S. Postal Service (USPS) and tracked to their delivery at England's National Physical Laboratory (NPL) by the United Kingdom Royal Mail. However, the project can only be viewed as a qualified successmore » as notable shortcomings were observed. Although the origin and terminus of all RFID-enabled shipments were recorded and no shipments were lost, not all the waypoints between ORNL and NPL were incorporated into the pilot. Given limited resources, the project team was able to install RFID listeners/actuators at three waypoints between the two endpoints. Although it is likely that all shipments followed the same route between ORNL and NPL, it cannot be determined beyond question that all 19 shipments were routed on identical itineraries past the same three waypoints. The pilot also raises the distinct possibility that unattended RFID tracking alone, without positive confirmation that a tagged item has been properly recorded by an RFID reader, does not meet a rigorous standard for shipping controlled items. Indeed, the proof of concept test strongly suggests that a multifaceted approach to tracking may be called for, including tracking methods that are capable of reading and accepting multiple inputs for individual items [e.g., carrier-provided tracking numbers, Universal Product Codes (UPCs), and RFID tags]. For controlled items, another apparent requirement is a confirmation feature, human or otherwise, which can certify that an item's RFID tag, UPC, or tracking number has been recorded.« less

Solid-state vs water-perfused catheters to measure colonic high-amplitude propagating contractions.

PubMed

Liem, O; Burgers, R E; Connor, F L; Benninga, M A; Reddy, S N; Mousa, H M; Di Lorenzo, C

2012-04-01

  Solid-state (SS) manometry catheters with portable data loggers offer many potential advantages over traditional water-perfused (WP) systems, such as prolonged recordings in a more physiologic ambulatory setting and the lack of risk for water overload. The use of SS catheters has not been evaluated in comparison with perfused catheters in children. This study aims to compare data provided by SS and WP catheters in children undergoing colonic manometry studies.   A SS catheter and a WP catheter were taped together such that their corresponding sensors were at the same location. Simultaneous recordings were obtained using the SS and WP catheters (both 8 channels, 10 cm apart) in 15 children with severe defecation disorders referred for colonic manometry. Signals were recorded for a minimum of 1 h during fasting, 1 h after ingestion of a meal, and 1 h after the administration of bisacodyl. Solid-state signals from the data logger were analyzed against the perfused signals. All high-amplitude propagated contractions (HAPCs), the most recognizable and interpreted colonic motor event, were evaluated for spatial and temporal features including their durations, amplitudes, and propagation velocities.   A total of 107 HAPCs were detected with SS and 91 with WP catheters. All WP-HAPC were also observed with SS. Linear regression analysis showed that SS catheters tended to give higher readings in the presence of amplitudes <102 mmHg and lower reading with amplitudes >102 mmHg. An opposite trend was found for the duration of contractions. No significant difference was found for HAPC velocity.   SS catheters are more sensitive in recording HAPCs in children with defecation disorders compared with the more traditional WP assembly. There is a difference in measurements of amplitude between the two systems. Solid-state catheters offer potential advantages over WP catheters in children, being portable, safer to use, and may provide data over a more prolonged period. © 2012 Blackwell Publishing Ltd.

Calibration of the Politrack® system based on CR39 solid-state nuclear track detectors for passive indoor radon concentration measurements.

PubMed

Kropat, G; Baechler, S; Bailat, C; Barazza, F; Bochud, F; Damet, J; Meyer, N; Palacios Gruson, M; Butterweck, G

2015-11-01

Swiss national requirements for measuring radon gas exposures demand a lower detection limit of 50 kBq h m(-3), representing the Swiss concentration average of 70 Bq m(-3) over a 1-month period. A solid-state nuclear track detector (SSNTD) system (Politrack, Mi.am s.r.l., Italy) has been acquired to fulfil these requirements. This work was aimed at the calibration of the Politrack system with traceability to international standards and the development of a procedure to check the stability of the system. A total of 275 SSNTDs was exposed to 11 different radon exposures in the radon chamber of the Secondary Calibration Laboratory at the Paul Scherrer Institute, Switzerland. The exposures ranged from 50 to 15000 kBq h m(-3). For each exposure of 20 detectors, 5 SSNTDs were used to monitor possible background exposures during transport and storage. The response curve and the calibration factor of the whole system were determined using a Monte Carlo fitting procedure. A device to produce CR39 samples with a reference number of tracks using a (241)Am source was developed for checking the long-term stability of the Politrack system. The characteristic limits for the detection of a possible system drift were determined following ISO Standard 11929. © The Author 2015. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Tracking the coupling of two electroencephalogram series in the isoflurane and remifentanil anesthesia.

PubMed

Liang, Zhenhu; Liang, Shujuan; Wang, Yinghua; Ouyang, Gaoxiang; Li, Xiaoli

2015-02-01

Coupling in multiple electroencephalogram (EEG) signals provides a perspective tool to understand the mechanism of brain communication. In this study, we propose a method based on permutation cross-mutual information (PCMI) to investigate whether or not the coupling between EEG series can be used to quantify the effect of specific anesthetic drugs (isoflurane and remifentanil) on brain activities. A Rössler-Lorenz system and surrogate analysis was first employed to compare histogram-based mutual information (HMI) and PCMI for estimating the coupling of two nonlinear systems. Then, the HMI and the PCMI indices of EEG recordings from two sides of the forehead of 12 patients undergoing combined remifentanil and isoflurane anesthesia were demonstrated for tracking the effect of drug on the coupling of brain activities. Performance of all indices was assessed by the correlation coefficients (Rij) and relative coefficient of variation (CV). The PCMI can track the coupling strength of two nonlinear systems, and it is sensitive to the phase change of the coupling systems. Compared to the HMI, the PCMI has a better correlation with the coupling strength in nonlinear systems. The PCMI could track the effect of anesthesia and distinguish the consciousness state from the unconsciousness state. Moreover, at the embedding dimension m=4 and lag τ=1, the PCMI had a better performance than HMI in tracking the effect of anesthesia drugs on brain activities. As a measure of coupling, the PCMI was able to reflect the state of consciousness from two EEG recordings. The PCMI is a promising new coupling measure for estimating the effect of isoflurane and remifentanil anesthetic drugs on the brain activity. Copyright © 2014 International Federation of Clinical Neurophysiology. All rights reserved.

Simultaneous Recordings of Human Microsaccades and Drifts with a Contemporary Video Eye Tracker and the Search Coil Technique

PubMed Central

McCamy, Michael B.; Otero-Millan, Jorge; Leigh, R. John; King, Susan A.; Schneider, Rosalyn M.; Macknik, Stephen L.; Martinez-Conde, Susana

2015-01-01

Human eyes move continuously, even during visual fixation. These “fixational eye movements” (FEMs) include microsaccades, intersaccadic drift and oculomotor tremor. Research in human FEMs has grown considerably in the last decade, facilitated by the manufacture of noninvasive, high-resolution/speed video-oculography eye trackers. Due to the small magnitude of FEMs, obtaining reliable data can be challenging, however, and depends critically on the sensitivity and precision of the eye tracking system. Yet, no study has conducted an in-depth comparison of human FEM recordings obtained with the search coil (considered the gold standard for measuring microsaccades and drift) and with contemporary, state-of-the art video trackers. Here we measured human microsaccades and drift simultaneously with the search coil and a popular state-of-the-art video tracker. We found that 95% of microsaccades detected with the search coil were also detected with the video tracker, and 95% of microsaccades detected with video tracking were also detected with the search coil, indicating substantial agreement between the two systems. Peak/mean velocities and main sequence slopes of microsaccades detected with video tracking were significantly higher than those of the same microsaccades detected with the search coil, however. Ocular drift was significantly correlated between the two systems, but drift speeds were higher with video tracking than with the search coil. Overall, our combined results suggest that contemporary video tracking now approaches the search coil for measuring FEMs. PMID:26035820

Near infrared lasers in flow cytometry.

PubMed

Telford, William G

2015-07-01

Technology development in flow cytometry has closely tracked laser technology, the light source that flow cytometers almost exclusively use to excite fluorescent probes. The original flow cytometers from the 1970s and 1980s used large water-cooled lasers to produce only one or two laser lines at a time. Modern cytometers can take advantage of the revolution in solid state laser technology to use almost any laser wavelength ranging from the ultraviolet to the near infrared. Commercial cytometers can now be equipped with many small solid state lasers, providing almost any wavelength needed for cellular analysis. Flow cytometers are now equipped to analyze 20 or more fluorescent probes simultaneously, requiring multiple laser wavelengths. Instrument developers are now trying to increase this number by designing fluorescent probes that can be excited by laser wavelength at the "edges" of the visible light range, in the near ultraviolet and near-infrared region. A variety of fluorescent probes have been developed that excite with violet and long wavelength ultraviolet light; however, the near-infrared range (660-800 nm) has yet seen only exploitation in flow cytometry. Fortunately, near-infrared laser diodes and other solid state laser technologies appropriate for flow cytometry have been in existence for some time, and can be readily incorporated into flow cytometers to accelerate fluorescent probe development. The near infrared region represents one of the last "frontiers" to maximize the number of fluorescent probes that can be analyzed by flow cytometry. In addition, near infrared fluorescent probes used in biomedical tracking and imaging could also be employed for flow cytometry with the correct laser wavelengths. This review describes the available technology, including lasers, fluorescent probes and detector technology optimal for near infrared signal detection. Published by Elsevier Inc.

Evaluation of a rapid breath hydrogen analyzer for clinical studies of carbohydrate absorption.

PubMed

Solomons, N W; Hamilton, L H; Christman, N T; Rothman, D

1983-05-01

A second-generation gas chromatograph for the analysis of H2 in expired air has been developed. It incorporates a solid-state detector with high sensitivity for H2 and has a small, internal pump which supplies air as the carrier gas, thus eliminating the need for a large tank of compressed gas for the carrier. A reference gas of known H2 concentration is, of course, still required. The entire system weighs 6.0 kg and is completely portable, requiring only 120 V electric current for use. The instrument has a mean intersample interval of less than 2 min, with H2 concentration registered on a digital display. The output has a track-hold feature which permits the output, in parts per million H2, to be retained by the meter so the reading can be verified. The chromatogram can also be recorded on a conventional analog strip-chart recorder. The sensitivity and precision are superior to those of a thermal conductivity H2 gas chromatograph. Moreover, the rapid response time encourages frequent calibration checks with the reference gas. This analyzer offers significant advantages over previous H2-measuring systems for breath-analysis tests used both for diagnostic clinical practice and for field studies of nutritional assessment.

Simulations of Neon Pellets for Plasma Disruption Mitigation in Tokamaks

NASA Astrophysics Data System (ADS)

Bosviel, Nicolas; Samulyak, Roman; Parks, Paul

2017-10-01

Numerical studies of the ablation of neon pellets in tokamaks in the plasma disruption mitigation parameter space have been performed using a time-dependent pellet ablation model based on the front tracking code FronTier-MHD. The main features of the model include the explicit tracking of the solid pellet/ablated gas interface, a self-consistent evolving potential distribution in the ablation cloud, JxB forces, atomic processes, and an improved electrical conductivity model. The equation of state model accounts for atomic processes in the ablation cloud as well as deviations from the ideal gas law in the dense, cold layers of neon gas near the pellet surface. Simulations predict processes in the ablation cloud and pellet ablation rates and address the sensitivity of pellet ablation processes to details of physics models, in particular the equation of state.

An Innovative Miniature Bite Force Recorder

PubMed Central

Utreja, Ashok K; Sandhu, Navreet; Dhaliwal, Yadvinder S

2011-01-01

In this study, a detailed description of development of a new novel bite force recorder (gnathodynamometer) using solid state components is vividly explained. This state of the art authenticated device can be used to assess the complex function of human bite force, which is the net resultant combination of functional response of various craniomandibular structures consisting of interrelated components, like the muscles of mastication, joints, teeth and the neuromuscular system. The consistency and accuracy of the bite force recorder was reaffirmed by doing a detailed laboratory calibration and clinical testing on 30 adult subjects. PMID:27672249

Quantitative Determination of Wax Contamination in Polystyrene HIPE Foam Using Solid-State NMR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cluff, Kyle James; Goodwin, Lynne Alese; Hamilton, Christopher Eric

Differences in molecular mobility between polystyrene foam and Brij-78 wax results in vast differences in the 1H nuclear magnetic resonance (NMR) linewidth. This allows for the convenient determination of wax content in the polystyrene foam components of inertial confinement fusion targets via solid-state NMR. Lastly, contamination levels as low as 0.1% are easily recognized and quantified, and the detection limit is calculated to be 0.02% even when only 32 transients are recorded.

Quantitative Determination of Wax Contamination in Polystyrene HIPE Foam Using Solid-State NMR

DOE PAGES

Cluff, Kyle James; Goodwin, Lynne Alese; Hamilton, Christopher Eric; ...

2017-11-29

Differences in molecular mobility between polystyrene foam and Brij-78 wax results in vast differences in the 1H nuclear magnetic resonance (NMR) linewidth. This allows for the convenient determination of wax content in the polystyrene foam components of inertial confinement fusion targets via solid-state NMR. Lastly, contamination levels as low as 0.1% are easily recognized and quantified, and the detection limit is calculated to be 0.02% even when only 32 transients are recorded.

Maui Optical Tracking and Identification Facility Transition Program.

DTIC Science & Technology

1981-08-01

USED) 2 OFFICE 19 LASER SUPPORT ROO 35 SERVICE CELL TECHT LIBARY 20 LASLAL 5 ATA LAB 36 UNDERGROUND WATER RESERVOIR S OFFICE 21 LOBBY 37 PUMP VAULT 8...precision at a rate of 50 samples per second on the system digital recorder along with time, housekeeping and ten selected dc channels which are recorded...with 12-bit precision at a rate of 90 samples per second (45 per mirror state). The digitally recorded ac and dc data can be retrieved post-mission and

Discriminative detection of deposited radon daughters on CR-39 track detectors using TRIAC II code

NASA Astrophysics Data System (ADS)

Patiris, D. L.; Ioannides, K. G.

2009-07-01

A method for detecting deposited 218Po and 214Po by a spectrometric study of CR-39 solid state nuclear track detectors is described. The method is based on the application of software imposed selection criteria, concerning the geometrical and optical properties of the tracks, which correspond to tracks created by alpha particles of specific energy falling on the detector at given angles of incidence. The selection criteria were based on a preliminary study of tracks' parameters (major and minor axes and mean value of brightness), using the TRIAC II code. Since no linear relation was found between the energy and the geometric characteristics of the tracks (major and minor axes), we resorted to the use of an additional parameter in order to classify the tracks according to the particles' energy. Since the brightness of tracks is associated with the tracks' depth, the mean value of brightness was chosen as the parameter of choice. To reduce the energy of the particles, which are emitted by deposited 218Po and 214Po into a quantifiable range, the detectors were covered with an aluminum absorber material. In this way, the discrimination of radon's daughters was finally accomplished by properly selecting amongst all registered tracks. This method could be applied as a low cost tool for the study of the radon's daughters behavior in air.

Cosmic ray particle dosimetry and trajectory tracing. [cosmic ray track analysis for Apollo 17 BIOCORE

NASA Technical Reports Server (NTRS)

Cruty, M. R.; Benton, E. V.; Turnbill, C. E.; Philpott, D. E.

1975-01-01

Five pocket mice (Perognathus longimembris) were flown on Apollo XVII, each with a solid-state (plastic) nuclear track detector implanted beneath its scalp. The subscalp detectors were sensitive to HZE cosmic ray particles with a LET greater than or approximately equal to 0.15 million electron volts per micrometer (MeV/micron). A critical aspect of the dosimetry of the experiment involved tracing individual particle trajectories through each mouse head from particle tracks registered in the individual subscalp detectors, thereby establishing a one-to-one correspondence between a trajectory location in the tissue and the presence or absence of a lesion. The other major aspect was the identification of each registered particle. An average of 16 particles with Z greater than or equal to 6 and 2.2 particles with Z greater than or equal to 20 were found per detector. The track density, 29 tracks/sq cm, when adjusted for detection volume, was in agreement with the photographic emulsion data from an area dosimeter located next to the flight package.

[Study on focusing chromatographic simultaneous determinations of 226Ra and its daughter nuclides by means of solid state alpha-tracks detection and beta-autoradiography (author's transl)].

PubMed

Furushima, K; Shinagawa, M

1980-09-01

In order to detect to radioactive band on the paper strip developed by focusing chromatography, plate-making-film was used for the autoradiography and beta-spots were photographed. Thereafter the film was etched with sodium hydroxide solution to find the alpha-tracks. Paper strip used for the sample was prepared by the precipitation focusing chromatography of 226Ra and its daughter nuclides using HCl-KF solution as a developer. The film used was not high in its beta-sensitivity, but because of its high resolution good photographic results were obtained according to the intensity of beta-activity when the proper conditions of photographic development were fulfilled. The simple alpha-spectrometry was made possible by counting the numbers of tracks according to the etching depth of the film. The film was hard and thick enough for etching with 6M sodium hydroxide solution at 50 degrees C for more than 50 hrs to measure the depth of tracks.

A Symmetric Inchworm Nanowalker

NASA Astrophysics Data System (ADS)

Chiang, Yi Herng

Intracellular transport by biological nanowalkers occurs in inchworm (IW) gait as well as hand-over-hand (HOH) gait. Multiple versions of artificial inchworm nanowalkers are also realized and proposed, but all rely on different 'head' and 'tail' to gain a direction. Here we demonstrate an inchworm bipedal nanowalker made of DNA that possesses two identical legs and moves directionally along a linear track under alternating ultraviolet and visible light. The inchworm gait is confirmed by operating the walker on a DNA duplex track that is designed to show a distinctive pattern for inchworm versus hand-over-hand gait. Interestingly, the same walker exhibits stride-controlled direction reversals and IW-to-HOH gait switch when the track is systematically modified for elongated spacing between periodic binding stations for the walker. The IW and HOH regimes altogether present an integrated nanowalker mechanism, which can be used to implement nanowalkers of different gaits and directions with DNA, other biomolecules or synthetic molecules on molecular tracks, optical potentials or even solid-state substrates.

Earth Orbiter 1: Wideband Advanced Recorder and Processor (WARP)

NASA Technical Reports Server (NTRS)

Smith, Terry; Kessler, John

1999-01-01

An advanced on-board spacecraft data system component is presented. The component is computer-based and provides science data acquisition, processing, storage, and base-band transmission functions. Specifically, the component is a very high rate solid state recorder, serving as a pathfinder for achieving the data handling requirements of next-generation hyperspectral imaging missions.

National Radar Conference, Los Angeles, CA, March 12, 13, 1986, Proceedings

NASA Astrophysics Data System (ADS)

The topics discussed include radar systems, radar subsystems, and radar signal processing. Papers are presented on millimeter wave radar for proximity fuzing of smart munitions, a solid state low pulse power ground surveillance radar, and the Radarsat prototype synthetic-aperture radar signal processor. Consideration is also given to automatic track quality assessment in ADT radar systems instrumentation of RCS measurements of modulation spectra of aircraft blades.

A Case Study of Learning, Motivation, and Performance Strategies for Teaching and Coaching CDE Teams

ERIC Educational Resources Information Center

Ball, Anna; Bowling, Amanda; Bird, Will

2016-01-01

This intrinsic case study examined the case of students on CDE (Career Development Event) teams preparing for state competitive events and the teacher preparing them in a school with a previous exemplary track record of winning multiple state and national career development events. The students were interviewed multiple times during the 16-week…

Development of a Tool for Documenting, Tracking, Recording, and Analyzing Improvements to Intersection Sites and Roadway Departures in Curve Locations : Research Project Capsule

DOT National Transportation Integrated Search

2012-09-01

Intermodal transportation : system planning, design, : improvement, performance : evaluation, or economic : assessments include safety : improvements because they : lower the overall cost of : transportation. State Departments of Transportation (DOTs...

AN ALTERNATIVE CALIBRATION OF CR-39 DETECTORS FOR RADON DETECTION BEYOND THE SATURATION LIMIT.

PubMed

Franci, Daniele; Aureli, Tommaso; Cardellini, Francesco

2016-12-01

Time-integrated measurements of indoor radon levels are commonly carried out using solid-state nuclear track detectors (SSNTDs), due to the numerous advantages offered by this radiation detection technique. However, the use of SSNTD also presents some problems that may affect the accuracy of the results. The effect of overlapping tracks often results in the underestimation of the detected track density, which leads to the reduction of the counting efficiency for increasing radon exposure. This article aims to address the effect of overlapping tracks by proposing an alternative calibration technique based on the measurement of the fraction of the detector surface covered by alpha tracks. The method has been tested against a set of Monte Carlo data and then applied to a set of experimental data collected at the radon chamber of the Istituto Nazionale di Metrologia delle Radiazioni Ionizzanti, at the ENEA centre in Casaccia, using CR-39 detectors. It has been proved that the method allows to extend the detectable range of radon exposure far beyond the intrinsic limit imposed by the standard calibration based on the track density. © The Author 2015. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Holographic investigation of solid propellant particulates

NASA Astrophysics Data System (ADS)

Gillespie, T. R.

1981-12-01

The investigation completed the development process to establish a technique to obtain holographic recordings of particulate behavior during the combustion process of solid propellants in a two-dimensional rocket motor. Holographic and photographic recordings were taken in a crossflow environment using various compositions of metallized propellants. The reconstructed holograms are used to provide data on the behavior of aluminum/aluminum oxide particulates in a steady state combustion environment as a function of the initial aluminum size cast into the propellant. High speed, high resolution motion pictures were taken to compare the cinematic data with that available from the holograms.

Decoupled direct tracking control system based on use of a virtual track for multilayer disk with a separate guide layer

NASA Astrophysics Data System (ADS)

Tanaka, Yukinobu; Ogata, Takeshi; Imagawa, Seiji

2015-09-01

We developed a decoupled direct tracking control system for multilayer optical disk that uses a separate guide layer. Data marks are recorded on a recording layer immediately above the guide layer by using two spatially separated spots with different wavelengths. Accurate data mark recording requires that the relative positions of the corresponding spots on the recording layer and guide layer are maintained. However, a disk tilt can shift their relative positions and cause previously recorded data marks to be overwritten. Additionally, a two-input/two-output control system is susceptible to mutual interference phenomenon between the two outputs, which can destabilize tracking control. A tracking control system based on use of data marks previously recorded as a virtual track has been developed that prevents spot shifting and mutual interference even if the disk tilt reaches 0.7°, thereby preventing overwriting.

Reconfigurable Solid-state Dye-doped Polymer Ring Resonator Lasers

NASA Astrophysics Data System (ADS)

Chandrahalim, Hengky; Fan, Xudong

2015-12-01

This paper presents wavelength configurable on-chip solid-state ring lasers fabricated by a single-mask standard lithography. The single- and coupled-ring resonator hosts were fabricated on a fused-silica wafer and filled with 3,3‧-Diethyloxacarbocyanine iodide (CY3), Rhodamine 6G (R6G), and 3,3‧-Diethylthiadicarbocyanine iodide (CY5)-doped polymer as the reconfigurable gain media. The recorded lasing threshold was ~220 nJ/mm2 per pulse for the single-ring resonator laser with R6G, marking the lowest threshold shown by solid-state dye-doped polymer lasers fabricated with a standard lithography process on a chip. A single-mode lasing from a coupled-ring resonator system with the lasing threshold of ~360 nJ/mm2 per pulse was also demonstrated through the Vernier effect. The renewability of the dye-doped polymer was examined by removing and redepositing the dye-doped polymer on the same resonator hosts for multiple cycles. We recorded consistent emissions from the devices for all trials, suggesting the feasibility of employing this technology for numerous photonic and biochemical sensing applications that entail for sustainable, reconfigurable, and low lasing threshold coherent light sources on a chip.

Reconfigurable Solid-state Dye-doped Polymer Ring Resonator Lasers

PubMed Central

Chandrahalim, Hengky; Fan, Xudong

2015-01-01

This paper presents wavelength configurable on-chip solid-state ring lasers fabricated by a single-mask standard lithography. The single- and coupled-ring resonator hosts were fabricated on a fused-silica wafer and filled with 3,3′-Diethyloxacarbocyanine iodide (CY3), Rhodamine 6G (R6G), and 3,3′-Diethylthiadicarbocyanine iodide (CY5)-doped polymer as the reconfigurable gain media. The recorded lasing threshold was ~220 nJ/mm2 per pulse for the single-ring resonator laser with R6G, marking the lowest threshold shown by solid-state dye-doped polymer lasers fabricated with a standard lithography process on a chip. A single-mode lasing from a coupled-ring resonator system with the lasing threshold of ~360 nJ/mm2 per pulse was also demonstrated through the Vernier effect. The renewability of the dye-doped polymer was examined by removing and redepositing the dye-doped polymer on the same resonator hosts for multiple cycles. We recorded consistent emissions from the devices for all trials, suggesting the feasibility of employing this technology for numerous photonic and biochemical sensing applications that entail for sustainable, reconfigurable, and low lasing threshold coherent light sources on a chip. PMID:26674508

Reconfigurable Solid-state Dye-doped Polymer Ring Resonator Lasers.

PubMed

Chandrahalim, Hengky; Fan, Xudong

2015-12-17

This paper presents wavelength configurable on-chip solid-state ring lasers fabricated by a single-mask standard lithography. The single- and coupled-ring resonator hosts were fabricated on a fused-silica wafer and filled with 3,3'-Diethyloxacarbocyanine iodide (CY3), Rhodamine 6G (R6G), and 3,3'-Diethylthiadicarbocyanine iodide (CY5)-doped polymer as the reconfigurable gain media. The recorded lasing threshold was ~220 nJ/mm(2) per pulse for the single-ring resonator laser with R6G, marking the lowest threshold shown by solid-state dye-doped polymer lasers fabricated with a standard lithography process on a chip. A single-mode lasing from a coupled-ring resonator system with the lasing threshold of ~360 nJ/mm(2) per pulse was also demonstrated through the Vernier effect. The renewability of the dye-doped polymer was examined by removing and redepositing the dye-doped polymer on the same resonator hosts for multiple cycles. We recorded consistent emissions from the devices for all trials, suggesting the feasibility of employing this technology for numerous photonic and biochemical sensing applications that entail for sustainable, reconfigurable, and low lasing threshold coherent light sources on a chip.

3D CAFE modeling of grain structures: application to primary dendritic and secondary eutectic solidification

NASA Astrophysics Data System (ADS)

Carozzani, T.; Digonnet, H.; Gandin, Ch-A.

2012-01-01

A three-dimensional model is presented for the prediction of grain structures formed in casting. It is based on direct tracking of grain boundaries using a cellular automaton (CA) method. The model is fully coupled with a solution of the heat flow computed with a finite element (FE) method. Several unique capabilities are implemented including (i) the possibility to track the development of several types of grain structures, e.g. dendritic and eutectic grains, (ii) a coupling scheme that permits iterations between the FE method and the CA method, and (iii) tabulated enthalpy curves for the solid and liquid phases that offer the possibility to work with multicomponent alloys. The present CAFE model is also fully parallelized and runs on a cluster of computers. Demonstration is provided by direct comparison between simulated and recorded cooling curves for a directionally solidified aluminum-7 wt% silicon alloy.

Detrital zircons and Earth system evolution

NASA Astrophysics Data System (ADS)

McKenzie, R.

2016-12-01

Zircon is a mineral commonly produced in silicic magmatism. Therefore, due to its resilience and exceedingly long residence times in the continental crust, detrital zircon records can be used to track processes associated with silicic magmatism throughout Earth history. In this contribution I will address the potential role of preservational biases in zircon record, and further discuss how zircon datasets can be used to help better understand the relationship between lithospheric and Earth system evolution. I will use large compilations of zircon data to trace the composition and weatherability of the continental crust, to evaluate temporal rates of crustal recycling, and finally to track spatiotemporal variation in continental arc magmatism and volcanic CO2 outgassing throughout Earth history. These records demonstrate that secular changes in plate tectonic regimes played a prominent role in modulating conditions of the ocean+atmosphere system and long-term climate state for the last 3 billion years.

Real-time eye tracking for the assessment of driver fatigue.

PubMed

Xu, Junli; Min, Jianliang; Hu, Jianfeng

2018-04-01

Eye-tracking is an important approach to collect evidence regarding some participants' driving fatigue. In this contribution, the authors present a non-intrusive system for evaluating driver fatigue by tracking eye movement behaviours. A real-time eye-tracker was used to monitor participants' eye state for collecting eye-movement data. These data are useful to get insights into assessing participants' fatigue state during monotonous driving. Ten healthy subjects performed continuous simulated driving for 1-2 h with eye state monitoring on a driving simulator in this study, and these measured features of the fixation time and the pupil area were recorded via using eye movement tracking device. For achieving a good cost-performance ratio and fast computation time, the fuzzy K -nearest neighbour was employed to evaluate and analyse the influence of different participants on the variations in the fixation duration and pupil area of drivers. The findings of this study indicated that there are significant differences in domain value distribution of the pupil area under the condition with normal and fatigue driving state. Result also suggests that the recognition accuracy by jackknife validation reaches to about 89% in average, implying that show a significant potential of real-time applicability of the proposed approach and is capable of detecting driver fatigue.

Real-time eye tracking for the assessment of driver fatigue

PubMed Central

Xu, Junli; Min, Jianliang

2018-01-01

Eye-tracking is an important approach to collect evidence regarding some participants’ driving fatigue. In this contribution, the authors present a non-intrusive system for evaluating driver fatigue by tracking eye movement behaviours. A real-time eye-tracker was used to monitor participants’ eye state for collecting eye-movement data. These data are useful to get insights into assessing participants’ fatigue state during monotonous driving. Ten healthy subjects performed continuous simulated driving for 1–2 h with eye state monitoring on a driving simulator in this study, and these measured features of the fixation time and the pupil area were recorded via using eye movement tracking device. For achieving a good cost-performance ratio and fast computation time, the fuzzy K-nearest neighbour was employed to evaluate and analyse the influence of different participants on the variations in the fixation duration and pupil area of drivers. The findings of this study indicated that there are significant differences in domain value distribution of the pupil area under the condition with normal and fatigue driving state. Result also suggests that the recognition accuracy by jackknife validation reaches to about 89% in average, implying that show a significant potential of real-time applicability of the proposed approach and is capable of detecting driver fatigue. PMID:29750113

Triple Resonance Solid State NMR Experiments with Reduced Dimensionality Evolution Periods

NASA Astrophysics Data System (ADS)

Astrof, Nathan S.; Lyon, Charles E.; Griffin, Robert G.

2001-10-01

Two solid state NMR triple resonance experiments which utilize the simultaneous incrementation of two chemical shift evolution periods to obtain a spectrum with reduced dimensionality are described. The CON CA experiment establishes the correlation of 13Ci-1 to 13Cαi and 15Ni by simultaneously encoding the 13COi-1 and 15Ni chemical shifts. The CAN COCA experiment establishes the correlation 13Cai and 15COi to 13Cαi-1 and 15Ni-1 within a single experiment by simultaneous encoding of the 13Cαi and 15Ni chemical shifts. This experiment establishes sequential amino acid correlations in close analogy to the solution state HNCA experiment. Reduced dimensionality 2D experiments are a practical alternative to recording multiple 3D data sets for the purpose of obtaining sequence-specific resonance assignments of peptides and proteins in the solid state.

Crash Position Indicator/Crash Survivable Flight Data Recorder Ejectable versus Nonejectable

DTIC Science & Technology

1983-07-27

for environmental protection. The radio beacon transmitter, antenna, and manual shutoff switch are molded into the airfoil foam. The battery and CSFDR...FWD BATERY LRADIO) BEACON ANTENNA TRANSMITTER SOLID-STATE FLIGHT INCIDENT RECORDER Figure 2 DEPLOYABLE FLIGHT INCIDENT RECORDER/CRASH POSITION LOCATOR...mechanical and thermal environment than do ejectable systems that depart the aircraft and clear the crash and fire. As a result of the more stringent

Synergy of elastic and inelastic energy loss on ion track formation in SrTiO 3

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weber, William J.; Zarkadoula, Eva; Pakarinen, Olli H.

2015-01-12

While the interaction of energetic ions with solids is well known to result in inelastic energy loss to electrons and elastic energy loss to atomic nuclei in the solid, the coupled effects of these energy losses on defect production, nanostructure evolution and phase transformations in ionic and covalently bonded materials are complex and not well understood due to dependencies on electron-electron scattering processes, electron-phonon coupling, localized electronic excitations, diffusivity of charged defects, and solid-state radiolysis. Here we show that a colossal synergy occurs between inelastic energy loss and pre-existing atomic defects created by elastic energy loss in single crystal strontiummore » titanate (SrTiO 3), resulting in the formation of nanometer-sized amorphous tracks, but only in the narrow region with pre-existing defects. These defects locally decrease the electronic and atomic thermal conductivities and increase electron-phonon coupling, which locally increase the intensity of the thermal spike for each ion. This work identifies a major gap in understanding on the role of defects in electronic energy dissipation and electron-phonon coupling; it also provides insights for creating novel interfaces and nanostructures to functionalize thin film structures, including tunable electronic, ionic, magnetic and optical properties.« less

Physical processes in wheel-rail contact and its implications on vehicle-track interaction

NASA Astrophysics Data System (ADS)

Six, K.; Meierhofer, A.; Müller, G.; Dietmaier, P.

2015-05-01

Friction within the wheel-rail contact highly influences all aspects of vehicle-track interaction. Models describing this frictional behaviour are of high relevance, for example, for reliable predictions on drive train dynamics. It has been shown by experiments, that the friction at a certain position on rail is not describable by only one number for the coefficient of friction. Beside the contact conditions (existence of liquids, solid third bodies, etc.) the vehicle speed, normal loading and contact geometry are further influencing factors. State-of-the-art models are not able to account for this sufficiently. Thus, an Extended-Creep-Force-Model was developed taking into account effects from third body layers. This model is able to describe all considered effects. In this way, a significant improvement of the prediction quality with respect to all aspects of vehicle-track interaction is expected.

A new method for evaluating radon and thoron alpha-activities per unit volume inside and outside various natural material samples by calculating SSNTD detection efficiencies for the emitted alpha-particles and measuring the resulting track densities.

PubMed

Misdaq, M A; Aitnouh, F; Khajmi, H; Ezzahery, H; Berrazzouk, S

2001-08-01

A Monte Carlo computer code for determining detection efficiencies of the CR-39 and LR-115 II solid-state nuclear track detectors (SSNTD) for alpha-particles emitted by the uranium and thorium series inside different natural material samples was developed. The influence of the alpha-particle initial energy on the SSNTD detection efficiencies was investigated. Radon (222Rn) and thoron (220Rn) alpha-activities per unit volume were evaluated inside and outside the natural material samples by exploiting data obtained for the detection efficiencies of the SSNTD utilized for the emitted alpha-particles, and measuring the resulting track densities. Results obtained were compared to those obtained by other methods. Radon emanation coefficients have been determined for some of the considered material samples.

EPA Facility Registry Service (FRS): RCRA

EPA Pesticide Factsheets

This web feature service contains location and facility identification information from EPA's Facility Registry Service (FRS) for the subset of hazardous waste facilities that link to the Resource Conservation and Recovery Act Information System (RCRAInfo). EPA's comprehensive information system in support of the Resource Conservation and Recovery Act (RCRA) of 1976 and the Hazardous and Solid Waste Amendments (HSWA) of 1984, RCRAInfo tracks many types of information about generators, transporters, treaters, storers, and disposers of hazardous waste. FRS identifies and geospatially locates facilities, sites or places subject to environmental regulations or of environmental interest. Using vigorous verification and data management procedures, FRS integrates facility data from EPA's national program systems, other federal agencies, and State and tribal master facility records and provides EPA with a centrally managed, single source of comprehensive and authoritative information on facilities. This data set contains the subset of FRS integrated facilities that link to RCRAInfo hazardous waste facilities once the RCRAInfo data has been integrated into the FRS database. Additional information on FRS is available at the EPA website https://www.epa.gov/enviro/facility-registry-service-frs

Preliminary Monitoring of Soil gas Radon in Potentially Active Faults, San Sai District, Chiang Mai Province, Thailand

NASA Astrophysics Data System (ADS)

Pondthai, P.; Udphuay, S.

2013-05-01

The magnitude of 5.1 Mw earthquake occurred in San Sai District, Chiang Mai Province, Thailand in December 2006 was considered an uncommon event due to the fact that there was no statistical record of such significant earthquake in the area. Therefore the earthquake might have been associated with a potentially active fault zone within the area. The objective of this study is to measure soil gas radon across this unknown fault zone within the Chiang Mai Basin, northern Thailand. Two profiles traversing the expected fault zone of soil gas radon measurements have been monitored, using TASTRAK solid state track nuclear detectors (SSNTDs). Radon signals from three periods of measurement show a distinctive consistent spatial distribution pattern. Anomalous radon areas along the profiles are connected to fault locations previously interpreted from other geophysical survey results. The increased radon signal changes from the radon background level with the signal-to-background ratio above 3 are considered anomalous. Such pattern of radon anomaly supports the existence of the faults. The radon measurement, therefore is a powerful technique in mapping active fault zone.

Utilizing Stable Isotopes and Isotopic Anomalies to Study Early Solar System Formation Processes

NASA Technical Reports Server (NTRS)

Simon, Justin

2017-01-01

Chondritic meteorites contain a diversity of particle components, i.e., chondrules and calcium-, aluminum-rich refractory inclusions (CAIs), that have survived since the formation of the Solar System. The chemical and isotopic compositions of these materials provide a record of the conditions present in the protoplanetary disk where they formed and can aid our understanding of the processes and reservoirs in which solids formed in the solar nebula, an important step leading to the accretion of planetesimals. Isotopic anomalies associated with nucleosynthetic processes are observed in these discrete materials, and can be compared to astronomical observations and astrophysical formation models of stars and more recently proplyds. The existence and size of these isotopic anomalies are typically thought to reflect a significant state of isotopic heterogeneity in the earliest Solar System, likely left over from molecular cloud heterogeneities on the grain scale, but some could also be due to late stellar injection. The homogenization of these isotopic anomalies towards planetary values can be used to track the efficiency and timescales of disk wide mixing,

Study of the optical properties and the carbonaceous clusters in DAM-ADC solid state nuclear track detectors

NASA Astrophysics Data System (ADS)

Rammah, Y. S.; Abdalla, A. M.

2017-12-01

The optical properties of DAM-ADC solid state nuclear track detectors (SSNTDs) were investigated. Samples of DAM-ADC detector were irradiated at room temperature with gamma doses in the range of 100-500 kGy using 1.25 MeV 60Co source of dose rate 4 kGy/h. The optical characterization of these detectors have been studied through the measurements of UV-visible absorption spectra of blank and γ- irradiated samples. The optical energy band gaps, Eg for the detectors were obtained from the direct and the indirect allowed transitions in K-space using two methods (Tauc's model and absorption spectrum fitting (ASF) method). The absorbance of DAM-ADC detector was found to increase with increasing of the gamma absorbed dose. The width of the tail of localized states in the band gap, Eu was evaluated with the Urbach's method. The number of carbon atoms per conjugated length (N), the number of carbon atoms per cluster (M), and refractive index (n) for the present samples were determined. Both of the direct and the indirect band gaps of DAM-ADC detector decrease with increasing of the gamma absorbed dose. Urbach's energy decreased significantly for the detector. An increase in N, M, and n with increasing of the gamma absorbed dose was noticed. Results shed light on the effect of gamma irradiations of DAM-ADC SSNTDs to suitable industrial applications and to modify the optical properties through gamma-induced modifications of the polymer structure.

Revisiting the cold season surge generating storms of the east coast in the 20th century

NASA Astrophysics Data System (ADS)

Lee, D. E.; Kushnir, Y.; Booth, J. F.

2014-12-01

Cold season storms in the East coast of the United States often threaten the coastal livelihood. This is a study to connect the recorded extreme cold season surges with the storms in the past, spanning from the early 20th Century. We find the 20th century reanalysis data (20CR) useful for this study, for its temporal coverage sufficiently overlaps with the modern tidal records. The storm tracks are obtained from the cold season (NDJFMA) sea level pressure field from 20CR, using the popular tracking algorithm by K.Hodges. In seeking for fidelity in the storm data, we made two major efforts: The climatology and the known climate signals imbedded in the track data are verified against those of ERA-interim reanalysis, and against the storms tracked by an independent algorithm (GISS-MCMS). In addition, it is statistically confirmed that the storm tracks and the sea level pressure fields based on 20CR around the east coast area exhibit temporal homogeneity. In the Battery, we select top 100 cold season water displacement events from the 6-hour mean water height data from 1927 to 2012, with linear trend and tide removed. Among the tracks passing close enough to the Battery, we found 91 matches. Distinctive track characteristics stand out when the positive surge events are separated from the negative surge events. More characteristic parameters of the storms are investigated according to further surge classification.

United States Coast Guard Fiscal Year 2009 Performance Report

DTIC Science & Technology

2010-02-01

flooding. The International Ice Patrol facilitates interna- tional commerce by broadcasting information on iceberg locations to vessels transiting...SEA also provided back-up capability for the U.S. Antarctic Deep Freeze resupply mission. • The United States Coast Guard International Ice Patrol...tracked over 1,200 icebergs which drifted into the transatlantic shipping lanes continuing its perfect record, 96 years, of preventing ship collisions

Acceptance of direct physician access to a computer-based patient record in a managed care setting.

PubMed

Dewey, J B; Manning, P; Brandt, S

1993-01-01

Kaiser Permanente Mid-Atlantic States has developed a fully integrated outpatient information system which currently runs on an IBM ES9000 on a VM platform written in MUMPS. The applications include Lab, Radiology, Transcription, Appointments. Pharmacy, Encounter tracking, Hospitalizations, Referrals, Phone Advice, Pap tracking, Problem list, Immunization tracking, and Patient demographics. They are department specific and require input and output from a dumb terminal. We have developed a physician's work station to access this information using PC compatible computers running Microsoft Windows and a custom Microsoft Visual Basic 2.0 environment which draws from these 14 applications giving the physician a comprehensive view of all electronic medical records. Through rapid prototyping, voluntary participation, formal training and gradual implementation we have created an enthusiastic response. 95% of our physician PC users access the system each month. The use ranges from 0.2 to 3.0 screens of data viewed per patient visit. This response continues to drive the process toward still greater user acceptance and further practice enhancement.

Cold Regions Test of Tracked and Wheeled Vehicles

DTIC Science & Technology

2015-12-11

with CTIS setting in the Highway setting and Mud, Sand and Snow setting. (7) Conduct the trials a minimum of three times at each speed as stated in...lock brake system. Record the stopping distance data and record any slew from the centerline. Document if the vehicle experiences engine stall ...while operating in snow. The TOP includes guidance for snow as well as mud, sand , swamps, and wet clay. Most conventional wheeled vehicles cannot

Experimental Aspects of Polarization Optimized Experiments (POE) for Magic Angle Spinning Solid-State NMR of Microcrystalline and Membrane-Bound Proteins.

PubMed

Gopinath, T; Veglia, Gianluigi

2018-01-01

Conventional NMR pulse sequences record one spectrum per experiment, while spending most of the time waiting for the spin system to return to the equilibrium. As a result, a full set of multidimensional NMR experiments for biological macromolecules may take up to several months to complete. Here, we present a practical guide for setting up a new class of MAS solid-state NMR experiments (POE or polarization optimized experiments) that enable the simultaneous acquisition of multiple spectra of proteins, accelerating data acquisition. POE exploit the long-lived 15 N polarization of isotopically labeled proteins and enable one to obtain up to eight spectra, by concatenating classical NMR pulse sequences. This new strategy propels data throughput of solid-state NMR spectroscopy of fibers, microcrystalline preparations, as well as membrane proteins.

Protein-nucleotide contacts in motor proteins detected by DNP-enhanced solid-state NMR.

PubMed

Wiegand, Thomas; Liao, Wei-Chih; Ong, Ta Chung; Däpp, Alexander; Cadalbert, Riccardo; Copéret, Christophe; Böckmann, Anja; Meier, Beat H

2017-11-01

DNP (dynamic nuclear polarization)-enhanced solid-state NMR is employed to directly detect protein-DNA and protein-ATP interactions and identify the residue type establishing the intermolecular contacts. While conventional solid-state NMR can detect protein-DNA interactions in large oligomeric protein assemblies in favorable cases, it typically suffers from low signal-to-noise ratios. We show here, for the oligomeric DnaB helicase from Helicobacter pylori complexed with ADP and single-stranded DNA, that this limitation can be overcome by using DNP-enhanced spectroscopy. Interactions are established by DNP-enhanced 31 P- 13 C polarization-transfer experiments followed by the recording of a 2D 13 C- 13 C correlation experiment. The NMR spectra were obtained in less than 2 days and allowed the identification of residues of the motor protein involved in nucleotide binding.

State of the art in video system performance

NASA Technical Reports Server (NTRS)

Lewis, Michael J.

1990-01-01

The closed circuit television (CCTV) system that is onboard the Space Shuttle has the following capabilities: camera, video signal switching and routing unit (VSU); and Space Shuttle video tape recorder. However, this system is inadequate for use with many experiments that require video imaging. In order to assess the state-of-the-art in video technology and data storage systems, a survey was conducted of the High Resolution, High Frame Rate Video Technology (HHVT) products. The performance of the state-of-the-art solid state cameras and image sensors, video recording systems, data transmission devices, and data storage systems versus users' requirements are shown graphically.

Automatic methods of the processing of data from track detectors on the basis of the PAVICOM facility

NASA Astrophysics Data System (ADS)

Aleksandrov, A. B.; Goncharova, L. A.; Davydov, D. A.; Publichenko, P. A.; Roganova, T. M.; Polukhina, N. G.; Feinberg, E. L.

2007-02-01

New automatic methods essentially simplify and increase the rate of the processing of data from track detectors. This provides a possibility of processing large data arrays and considerably improves their statistical significance. This fact predetermines the development of new experiments which plan to use large-volume targets, large-area emulsion, and solid-state track detectors [1]. In this regard, the problem of training qualified physicists who are capable of operating modern automatic equipment is very important. Annually, about ten Moscow students master the new methods, working at the Lebedev Physical Institute at the PAVICOM facility [2 4]. Most students specializing in high-energy physics are only given an idea of archaic manual methods of the processing of data from track detectors. In 2005, on the basis of the PAVICOM facility and the physicstraining course of Moscow State University, a new training work was prepared. This work is devoted to the determination of the energy of neutrons passing through a nuclear emulsion. It provides the possibility of acquiring basic practical skills of the processing of data from track detectors using automatic equipment and can be included in the educational process of students of any physical faculty. Those who have mastered the methods of automatic data processing in a simple and pictorial example of track detectors will be able to apply their knowledge in various fields of science and technique. Formulation of training works for pregraduate and graduate students is a new additional aspect of application of the PAVICOM facility described earlier in [4].

Solid state instrumentation concepts for earth resource observation

NASA Technical Reports Server (NTRS)

Richard, H. L.

1982-01-01

Late in 1980, specifications were prepared for detail design definition of a six band solid state multispectral instrument having three visible (VIS), one near infrared (NIR), and two short wave infrared (SWIR) bands. This instrument concept, known as the Multispectral Linear Array (MLA), also offered increased spatial resolution, on board gain and offset correction, and additional operational modes which would allow for cross track and stereoscopic viewing as well as a multialtitude operational capability. A description is presented of a summary of some of the salient features of four different MLA design concepts, as developed by four American companies. The designs ranged from the use of multiple refractive telescopes utilizing three groups of focal plane detectors electronic correlation processing for achieving spatial registration, and incorporating palladium silicide (PdSi) SWIR detectors, to a four-mirror all-reflective telecentric system utilizing a beam splitter for spatial registration.

Coherent diffractive imaging of solid state reactions in zinc oxide crystals

NASA Astrophysics Data System (ADS)

Leake, Steven J.; Harder, Ross; Robinson, Ian K.

2011-11-01

We investigated the doping of zinc oxide (ZnO) microcrystals with iron and nickel via in situ coherent x-ray diffractive imaging (CXDI) in vacuum. Evaporated thin metal films were deposited onto the ZnO microcrystals. A single crystal was selected and tracked through annealing cycles. A solid state reaction was observed in both iron and nickel experiments using CXDI. A combination of the shrink wrap and guided hybrid-input-output phasing methods were applied to retrieve the electron density. The resolution was 33 nm (half order) determined via the phase retrieval transfer function. The resulting images are nevertheless sensitive to sub-angstrom displacements. The exterior of the microcrystal was found to degrade dramatically. The annealing of ZnO microcrystals coated with metal thin films proved an unsuitable doping method. In addition the observed defect structure of one crystal was attributed to the presence of an array of defects and was found to change upon annealing.

1 Hz fast-heating fusion driver HAMA pumped by a 10 J green diode-pumped solid-state laser

NASA Astrophysics Data System (ADS)

Mori, Y.; Sekine, T.; Komeda, O.; Nakayama, S.; Ishii, K.; Hanayama, R.; Fujita, K.; Okihara, S.; Satoh, N.; Kurita, T.; Kawashima, T.; Kan, H.; Nakamura, N.; Kondo, T.; Fujine, M.; Azuma, H.; Hioki, T.; Kakeno, M.; Motohiro, T.; Nishimura, Y.; Sunahara, A.; Sentoku, Y.; Kitagawa, Y.

2013-07-01

A Ti : sapphire laser HAMA pumped by a diode-pumped solid-state laser (DPSSL) is developed to enable a high-repetitive inertial confinement fusion (ICF) experiment to be conducted. To demonstrate a counter-irradiation fast-heating fusion scheme, a 3.8 J, 0.4 ns amplified chirped pulse is divided into four beams: two counter-irradiate a target with intensities of 6 × 1013 W cm-2, and the remaining two are pulse-compressed to 110 fs for heating the imploded target with intensities of 2 × 1017 W cm-2. HAMA contributed to the first demonstration by showing that a 10 J class DPSSL is adaptable to ICF experiments and succeeded in DD neutron generation in the repetition mode. Based on HAMA, we can design and develop an integrated repetitive ICF experiment machine by including target injection and tracking.

Tape tracking and handling for magnetic tape recorders. [aboard spacecraft

NASA Technical Reports Server (NTRS)

Paroby, W.; Disilvestre, R.

1975-01-01

One of the critical performance and life limiting elements of a spacecraft tape recorder instrumentation system which has received little attention in technical literature is magnetic tape tracking and handling technology. This technology is required to understand how to gently transfer tape from one reel to another with proper alignment and a desirable uniform velocity at the read and write transducer heads. The increased demand for high data rate (i.e., multi-track spacecraft recording instrumentation systems), coupled with performance under extreme environmental conditions, requires a thorough knowledge of the various parameters which establish an optimum designed tape tracking and handling system. Stress analysis techniques are required to evaluate these parameters substantiated with test tape tracking data, to show the effect of each parameter on a tape recorder instrumentation tracking system. The technology is applicable to ground type tape recorders where the detrimental effects of edge guidance can be eliminated.

77 FR 23765 - Privacy Act; Termination of Three Systems of Records

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-20

... terminating the following Systems of Records: MSPB/Internal 5, ``Workload and Assignment Tracking System... Tracking System.'' They are no longer in use. DATES: Effective April 6, 2012. FOR FURTHER INFORMATION... systems of records: MSPB/Internal 5, ``Workload and Assignment Tracking System;'' MSPB/Internal 7...

LayTracks3D: A new approach for meshing general solids using medial axis transform

DOE PAGES

Quadros, William Roshan

2015-08-22

This study presents an extension of the all-quad meshing algorithm called LayTracks to generate high quality hex-dominant meshes of general solids. LayTracks3D uses the mapping between the Medial Axis (MA) and the boundary of the 3D domain to decompose complex 3D domains into simpler domains called Tracks. Tracks in 3D have no branches and are symmetric, non-intersecting, orthogonal to the boundary, and the shortest path from the MA to the boundary. These properties of tracks result in desired meshes with near cube shape elements at the boundary, structured mesh along the boundary normal with any irregular nodes restricted to themore » MA, and sharp boundary feature preservation. The algorithm has been tested on a few industrial CAD models and hex-dominant meshes are shown in the Results section. Work is underway to extend LayTracks3D to generate all-hex meshes.« less

A state-based approach to trend recognition and failure prediction for the Space Station Freedom

NASA Technical Reports Server (NTRS)

Nelson, Kyle S.; Hadden, George D.

1992-01-01

A state-based reasoning approach to trend recognition and failure prediction for the Altitude Determination, and Control System (ADCS) of the Space Station Freedom (SSF) is described. The problem domain is characterized by features (e.g., trends and impending failures) that develop over a variety of time spans, anywhere from several minutes to several years. Our state-based reasoning approach, coupled with intelligent data screening, allows features to be tracked as they develop in a time-dependent manner. That is, each state machine has the ability to encode a time frame for the feature it detects. As features are detected, they are recorded and can be used as input to other state machines, creating a hierarchical feature recognition scheme. Furthermore, each machine can operate independently of the others, allowing simultaneous tracking of features. State-based reasoning was implemented in the trend recognition and the prognostic modules of a prototype Space Station Freedom Maintenance and Diagnostic System (SSFMDS) developed at Honeywell's Systems and Research Center.

Ionizing radiation fluxes and dose measurements during the Kosmos 1887 satellite flight.

PubMed

Charvat, J; Spurny, F; Kopecka, B; Votockova, I

1990-01-01

The results of dosimetric experiments performed during the flight of Kosmos 1887 biosatellite are presented. Two kinds of measurements were performed on the external surface of the satellite. First, the fluences and spectra of low energy charged particles were established. It was found that most of the particles registered by means of solid state nuclear track detectors are helium nuclei. Tracks of oxygen nuclei and some heavier charged particles were also observed. Thermoluminescent detectors were used to establish absorbed doses in open space on the satellite's surface and behind thin shielding. It was found that these doses were rather high; nevertheless, their decrease with shielding thickness is very rapid. Dosimetric and other consequences of the results obtained are analyzed and discussed.

A reappraisal of the Middle Triassic chirotheriid Chirotherium ibericus Navás, 1906 (Iberian Range NE Spain), with comments on the Triassic tetrapod track biochronology of the Iberian Peninsula

PubMed Central

Castanera, Diego; Gasca, José Manuel; Canudo, José Ignacio

2015-01-01

Triassic vertebrate tracks are known from the beginning of the 19th century and have a worldwide distribution. Several Triassic track ichnoassemblages and ichnotaxa have a restricted stratigraphic range and are useful in biochronology and biostratigraphy. The record of Triassic tracks in the Iberian Peninsula has gone almost unnoticed although more than 25 localities have been described since 1897. In one of these localities, the naturalist Longinos Navás described the ichnotaxon Chirotherium ibericus in 1906.The vertebrate tracks are in two sandy slabs from the Anisian (Middle Triassic) of the Moncayo massif (Zaragoza, Spain). In a recent revision, new, previously undescribed vertebrate tracks have been identified. The tracks considered to be C. ibericus as well as other tracks with the same morphology from both slabs have been classified as Chirotherium barthii. The rest of the tracks have been assigned to Chirotheriidae indet., Rhynchosauroides isp. and undetermined material. This new identification of C. barthii at the Navás site adds new data to the Iberian record of this ichnotaxon, which is characterized by the small size of the tracks when compared with the main occurrences of this ichnotaxon elsewhere. As at the Navás tracksite, the Anisian C. barthii-Rhynchosauroides ichnoassemblage has been found in other coeval localities in Iberia and worldwide. This ichnoassemblage belongs to the upper Olenekian-lower Anisian interval according to previous biochronological proposals. Analysis of the Triassic Iberian record of tetrapod tracks is uneven in terms of abundance over time. From the earliest Triassic to the latest Lower Triassic the record is very scarce, with Rhynchosauroides being the only known ichnotaxon. Rhynchosauroides covers a wide temporal range and gives poor information for biochronology. The record from the uppermost Lower Triassic to the Middle Triassic is abundant. The highest ichnodiversity has been reported for the Anisian with an assemblage composed of Dicynodontipus, Procolophonichnium, Rhynchosauroides, Rotodactylus, Chirotherium, Isochirotherium, Coelurosaurichnus and Paratrisauropus. The Iberian track record from the Anisian is coherent with the global biochronology proposed for Triassic tetrapod tracks. Nevertheless, the scarcity of track occurrences during the late Olenekian and Ladinian prevents analysis of the corresponding biochrons. Finally, although the Iberian record for the Upper Triassic is not abundant, the presence of Eubrontes, Anchisauripus and probably Brachychirotherium is coherent with the global track biochronology as well. Thus, the Triassic track record in the Iberian Peninsula matches the expected record for this age on the basis of a global biochronological approach, supporting the idea that vertebrate Triassic tracks are a useful tool in biochronology. PMID:26137425

Analysis of Project Finance | Energy Analysis | NREL

Science.gov Websites

project finance is complex, requiring knowledge of federal tax credits, state-level incentives, renewable and in lieu of the 30% federal investment tax credit, as follows: Less-established renewable power that lack extensive operational track records may be slowed because many tax equity investors are seen

Role of Dynamically Frustrated Bond Disorder in a Li + Superionic Solid Electrolyte

DOE PAGES

Adelstein, Nicole; Wood, Brandon C.

2016-09-16

Inorganic lithium solid electrolytes are critical components in next-generation solid-state batteries, yet the fundamental nature of the cation-anion interactions and their relevance for ionic conductivity in these materials remains enigmatic. Here, we employ first-principles molecular dynamics simulations to explore the interplay between chemistry, structure, and functionality of a highly conductive Li + solid electrolyte, Li3InBr6. Using local-orbital projections to dynamically track the evolution of the electronic charge density, the simulations reveal rapid, correlated fluctuations between cation-anion interactions with different degrees of directional covalent character. These chemical bond dynamics are shown to correlate with Li + mobility, and are enabled thermallymore » by intrinsic frustration between the preferred geometries of chemical bonding and lattice symmetry. We suggest that the fluctuating chemical environment from the polarizable anions functions similar to a solvent, contributing to the superionic behavior of Li 3InBr 6 by temporarily stabilizing configurations favorable for migrating Li +. The generality of these conclusions for understanding solid electrolytes and key factors governing the superionic phase transition is discussed.« less

Reduced Noise UV Enhancement of Etch Rates for Nuclear Tracks in CR-39

NASA Astrophysics Data System (ADS)

Sheets, Rebecca; Clarkson, David; Ume, Rubab; Regan, Sean; Sangster, Craig; Padalino, Stephen; McLean, James

2016-10-01

The use of CR-39 plastic as a Solid State Nuclear Track Detector is an effective technique for obtaining data in high-energy particle experiments including inertial confinement fusion. To reveal particle tracks after irradiation, CR-39 is chemically etched in NaOH at 80°C for 6 hours, producing micron-scale signal pits at the nuclear track sites. Using CR-39 irradiated with 5.4 MeV alpha particles and 1.0 MeV protons, we show that exposing the CR-39 to high intensity UV light before etching, with wavelengths between 240 nm and 350 nm, speeds the etch process. Elevated temperatures during UV exposure amplifies this effect, with etch rates up to 50% greater than unprocessed conditions. CR-39 pieces exposed to UV light and heat can also exhibit heightened levels of etch-induced noise (surface features not caused by nuclear particles). By illuminating the CR-39 from the side opposite to the tracks, a similar level of etch enhancement was obtained with little to no noise. The effective wavelength range is reduced, due to strong attenuation of shorter wavelengths. Funded in part by a LLE contract through the DOE.

Sequence stratigraphic controls on synsedimentary cementation and preservation of dinosaur tracks: Example from the lower Cretaceous, (Upper Albian) Dakota Formation, Southeastern Nebraska, U.S.A.

USGS Publications Warehouse

Phillips, P.L.; Ludvigson, Greg A.; Matthew, Joeckel R.; Gonzalez, Luis A.; Brenner, Richard L.; Witzke, B.J.

2007-01-01

A thin cemented sandstone bed in the Upper Albian Dakota Formation of southeastern Nebraska contains the first dinosaur tracks to be described from the state. Of equal importance to the tracks are stable-isotope (C, O) analyses of cements in the track bed, especially in the context of data derived from generally correlative strata (sandstones and sphaerosiderite-bearing paleosols) in the region. These data provide the framework for interpretations of paleoenvironmental conditions, as well as a novel approach to understanding mechanisms of terrestrial vertebrate track preservation. High minus-cement-porosity (> 47%) and low grain-to-grain contacts (???2.5) in the track bed indicate early (pre-compaction) lithification. Although phreatic cements dominate, the history of cementation within this stratigraphic interval is complex. Cathodoluminescence petrography reveals two distinct calcite zones in the track-bearing horizon and four cement zones in stratigraphically equivalent strata from a nearby section. The earliest calcite cements from both localities are likely coeval because they exhibit identical positive covariant trends (??18O values of - 9.89 to - 6.32??? and ??13C values of - 28.01 to - 19.33??? VPDB) and record mixing of brackish and meteoric groundwaters. All other calcite cements define meteoric calcite lines with ??18O values clustering around - 9.42??? and - 8.21??? VPDB from the track-bearing horizon, and - 7.74???, - 5.81???, and - 3.95??? VPDB from the neighboring section. Distinct meteoric sphaerosiderite lines from roughly correlative paleosols serve as a proxy for locally recharged groundwaters. Back-calculated paleogroundwater ??18O estimates from paleosol sphaerosiderites range from - 7.4 to - 4.2??? SMOW; whereas, meteoric calcite lines from the track horizon are generally more depleted. Differences in cement ??18O values record changes in paleogroundwater recharge areas over time. Early calcite cements indicate mixing of fresh and brackish groundwaters during the syndepositional lithification of the track horizon. Later calcite cements, however, indicate recharge from a larger catchment basin that extended far inland. Therefore, the cements likely record a rise and subsequent fall in relative sea level. We conclude that scrutiny of the cement isotope geochemistry of genetically significant surfaces, especially track beds, can provide new data for interpreting sea level change. ?? 2006 Elsevier B.V. All rights reserved.

Triple tracks in CR-39 as the result of Pd-D Co-deposition: evidence of energetic neutrons.

PubMed

Mosier-Boss, Pamela A; Szpak, Stanislaw; Gordon, Frank E; Forsley, Lawrence P G

2009-01-01

Since the announcement by Fleischmann and Pons that the excess enthalpy generated in the negatively polarized Pd-D-D(2)O system was attributable to nuclear reactions occurring inside the Pd lattice, there have been reports of other manifestations of nuclear activities in this system. In particular, there have been reports of tritium and helium-4 production; emission of energetic particles, gamma or X-rays, and neutrons; as well as the transmutation of elements. In this communication, the results of Pd-D co-deposition experiments conducted with the cathode in close contact with CR-39, a solid-state nuclear etch detector, are reported. Among the solitary tracks due to individual energetic particles, triple tracks are observed. Microscopic examination of the bottom of the triple track pit shows that the three lobes of the track are splitting apart from a center point. The presence of three alpha-particle tracks outgoing from a single point is diagnostic of the (12)C(n,n')3alpha carbon breakup reaction and suggests that DT reactions that produce > or = 9.6 MeV neutrons are occurring inside the Pd lattice. To our knowledge, this is the first report of the production of energetic (> or = 9.6 MeV) neutrons in the Pd-D system.

Refocused linewidths less than 10 Hz in 1H solid-state NMR.

PubMed

Paruzzo, Federico M; Stevanato, Gabriele; Halse, Meghan E; Schlagnitweit, Judith; Mammoli, Daniele; Lesage, Anne; Emsley, Lyndon

2018-06-02

Coherence lifetimes in homonuclear dipolar decoupled 1 H solid-state NMR experiments are usually on the order of a few ms. We discover an oscillation that limits the lifetime of the coherences by recording spin-echo dephasing curves. We find that this oscillation can be removed by the application of a double spin-echo experiment, leading to coherence lifetimes of more than 45 ms in adamantane and more that 22 ms in β-AspAla, corresponding to refocused linewidths of less than 7 and 14 Hz respectively. Copyright © 2018 Elsevier Inc. All rights reserved.

Determination of Pu and 241Am in soils by instrumental methods

NASA Astrophysics Data System (ADS)

Yaroshevich, O. J.; Zhuk, I. V.; Lomonosova, E. M.; Svetlakova, N. N.; Mironov, V. P.; Kudryashov, V. P.; Bushuev, A. V.

1995-06-01

A method based on the detection of x- and low energy γ-radiation for determining the activity of plutonium and americium-241 in soils and sediments is described. The results of x- and γ-radiation spectral measurements are presented. Possible ways to increase the sensitivity of the method are discussed. The results of measurements of α-particle activity distributions with solid state nuclear track detectors for depth profiling of different types of soils are also presented.

Integrated cluster management at Manchester

NASA Astrophysics Data System (ADS)

McNab, Andrew; Forti, Alessandra

2012-12-01

We describe an integrated management system using third-party, open source components used in operating a large Tier-2 site for particle physics. This system tracks individual assets and records their attributes such as MAC and IP addresses; derives DNS and DHCP configurations from this database; creates each host's installation and re-configuration scripts; monitors the services on each host according to the records of what should be running; and cross references tickets with asset records and per-asset monitoring pages. In addition, scripts which detect problems and automatically remove hosts record these new states in the database which are available to operators immediately through the same interface as tickets and monitoring.

Biomimetic photo-actuation: sensing, control and actuation in sun-tracking plants.

PubMed

Dicker, M P M; Rossiter, J M; Bond, I P; Weaver, P M

2014-09-01

Although the actuation mechanisms that drive plant movement have been investigated from a biomimetic perspective, few studies have looked at the wider sensing and control systems that regulate this motion. This paper examines photo-actuation-actuation induced by, and controlled with light-through a review of the sun-tracking functions of the Cornish Mallow. The sun-tracking movement of the Cornish Mallow leaf results from an extraordinarily complex-yet extremely elegant-process of signal perception, generation, filtering and control. Inspired by this process, a concept for a simplified biomimetic analogue of this leaf is proposed: a multifunctional structure employing chemical sensing, signal transmission, and control of composite hydrogel actuators. We present this multifunctional structure, and show that the success of the concept will require improved selection of materials and structural design. This device has application in the solar-tracking of photovoltaic panels for increased energy yield. More broadly it is envisaged that the concept of chemical sensing and control can be expanded beyond photo-actuation to many other stimuli, resulting in new classes of robust solid-state devices.

A rocket-borne energy spectrometer using multiple solid-state detectors for particle identification

NASA Technical Reports Server (NTRS)

Fries, K. L.; Smith, L. G.; Voss, H. D.

1979-01-01

A rocket-borne experiment using energy spectrometers that allows particle identification by the use of multiple solid-state detectors is described. The instrumentation provides information regarding the energy spectrum, pitch-angle distribution, and the type of energetic particles present in the ionosphere. Particle identification was accomplished by considering detector loss mechanisms and their effects on various types of particles. Solid state detectors with gold and aluminum surfaces of several thicknesses were used. The ratios of measured energies for the various detectors were compared against known relationships during ground-based analysis. Pitch-angle information was obtained by using detectors with small geometrical factors mounted with several look angles. Particle flux was recorded as a function of rocket azimuth angle. By considering the rocket azimuth, the rocket precession, and the location of the detectors on the rocket, the pitched angle of the incident particles was derived.

77 FR 66793 - Privacy Act of 1974, System of Records

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-07

... Tracking, system of records in its existing inventory. DATES: This proposed action will be effective on..., USAID is deleting the AID-29 Deployment Tracking system of records because it was never activated. Dated...-29 Deployment Tracking Reason: Based upon a review of AID-29, it has been determined that this system...

CASSIUS: The Cassini Uplink Scheduler

NASA Technical Reports Server (NTRS)

Bellinger, Earl

2012-01-01

The Cassini Uplink Scheduler (CASSIUS) is cross-platform software used to generate a radiation sequence plan for commands being sent to the Cassini spacecraft. Because signals must travel through varying amounts of Earth's atmosphere, several different modes of constant telemetry rates have been devised. These modes guarantee that the spacecraft and the Deep Space Network agree with respect to the data transmission rate. However, the memory readout of a command will be lost if it occurs on a telemetry mode boundary. Given a list of spacecraft message files as well as the available telemetry modes, CASSIUS can find an uplink sequence that ensures safe transmission of each file. In addition, it can predict when the two on-board solid state recorders will swap. CASSIUS prevents data corruption by making sure that commands are not planned for memory readout during telemetry rate changes or a solid state recorder swap.

Gas Electron Multipler (GEM) detectors for parity-violating electron scattering experiments at Jefferson Lab

NASA Astrophysics Data System (ADS)

Matter, John; Gnanvo, Kondo; Liyanage, Nilanga; Solid Collaboration; Moller Collaboration

2017-09-01

The JLab Parity Violation In Deep Inelastic Scattering (PVDIS) experiment will use the upgraded 12 GeV beam and proposed Solenoidal Large Intensity Device (SoLID) to measure the parity-violating electroweak asymmetry in DIS of polarized electrons with high precision in order to search for physics beyond the Standard Model. Unlike many prior Parity-Violating Electron Scattering (PVES) experiments, PVDIS is a single-particle tracking experiment. Furthermore the experiment's high luminosity combined with the SoLID spectrometer's open configuration creates high-background conditions. As such, the PVDIS experiment has the most demanding tracking detector needs of any PVES experiment to date, requiring precision detectors capable of operating at high-rate conditions in PVDIS's full production luminosity. Developments in large-area GEM detector R&D and SoLID simulations have demonstrated that GEMs provide a cost-effective solution for PVDIS's tracking needs. The integrating-detector-based JLab Measurement Of Lepton Lepton Electroweak Reaction (MOLLER) experiment requires high-precision tracking for acceptance calibration. Large-area GEMs will be used as tracking detectors for MOLLER as well. The conceptual designs of GEM detectors for the PVDIS and MOLLER experiments will be presented.

Front tracking based modeling of the solid grain growth on the adaptive control volume grid

NASA Astrophysics Data System (ADS)

Seredyński, Mirosław; Łapka, Piotr

2017-07-01

The paper presents the micro-scale model of unconstrained solidification of the grain immersed in under-cooled liquid, based on the front tracking approach. For this length scale, the interface tracked through the domain is meant as the solid-liquid boundary. To prevent generation of huge meshes the energy transport equation is discretized on the adaptive control volume (c.v.) mesh. The coupling of dynamically changing mesh and moving front position is addressed. Preliminary results of simulation of a test case, the growth of single grain, are presented and discussed.

Quantitative approach to track lipase producing Pseudomonas sp. S1 in nonsterilized solid state fermentation.

PubMed

Sahoo, R K; Subudhi, E; Kumar, M

2014-06-01

Proliferation of the inoculated Pseudomonas sp. S1 is quantitatively evaluated using ERIC-PCR during the production of lipase in nonsterile solid state fermentation an approach to reduce the cost of enzyme production. Under nonsterile solid state fermentation with olive oil cake, Pseudomonas sp. S1 produced 57·9 IU g(-1) of lipase. DNA fingerprints of unknown bacterial isolates obtained on Bushnell Haas agar (BHA) + tributyrin exactly matched with that of Pseudomonas sp. S1. Using PCR-based enumeration, population of Pseudomonas sp. S1 was proliferated from 7·6 × 10(4) CFU g(-1) after 24 h to 4·6 × 10(8) CFU g(-1) after 96 h, which tallied with the maximum lipase activity as compared to control. Under submerged fermentation (SmF), Pseudomonas sp. S1 produced maximum lipase (49 IU ml(-1) ) using olive oil as substrate, while lipase production was 9·754 IU ml(-1) when Pseudomonas sp. S1 was grown on tributyrin. Optimum pH and temperature of the crude lipase was 7·0 and 50°C. Crude enzyme activity was 71·2% stable at 50°C for 360 min. Pseudomonas sp. S1 lipase was also stable in methanol showing 91·6% activity in the presence of 15% methanol, whereas 75·5 and 51·1% of activity were retained in the presence of 20 and 30% methanol, respectively. Thus, lipase produced by Pseudomonas sp. S1 is suitable for the production of biodiesel as well as treatment of oily waste water. This study presents the first report on the production of thermophilic organic solvent tolerant lipase using agro-industry waste in nonsterile solid state fermentation. Positive correlation between survival of Pseudomonas sp. S1 and lipase production under nonsterile solid state fermentation was established, which may emphasize the need to combine molecular tools and solid state fermentation in future studies. Our study brings new insights into the lipase production in cost-effective manner, which is an industrially relevant approach. © 2014 The Society for Applied Microbiology.

Swim track kinematics and calling behavior attributed to Bryde's whales on the Navy's Pacific Missile Range Facility.

PubMed

Helble, Tyler A; Henderson, E Elizabeth; Ierley, Glenn R; Martin, Stephen W

2016-12-01

Time difference of arrival methods for acoustically localizing multiple marine mammals have been applied to recorded data from the Navy's Pacific Missile Range Facility in order to localize and track calls attributed to Bryde's whales. Data were recorded during the months of August-October 2014, and 17 individual tracks were identified. Call characteristics were compared to other Bryde's whale vocalizations from the Pacific Ocean, and locations of the recorded signals were compared to published visual sightings of Bryde's whales in the Hawaiian archipelago. Track kinematic information, such as swim speeds, bearing information, track duration, and directivity, was recorded for the species. The intercall interval was also established for most of the tracks, providing cue rate information for this species that may be useful for future acoustic density estimate calculations.

Performance and brain electrical activity during prolonged confinement.

PubMed

Lorenz, B; Lorenz, J; Manzey, D

1996-01-01

A subset of the AGARD-STRES battery including memory search, unstable tracking, and a combination of both tasks (dual-task), was applied repeatedly to the four chamber crew members before, during, and after the 60-day isolation period of EXEMSI. Five ground control group members served as a control group. A subjective state questionnaire was also included. The results were subjected to a quantitative single-subject analysis. Electroencephalograms (EEG) were recorded to permit correlation of changes in task performance with changes in the physiological state. Evaluation of the EEG focused on spectral parameters of spontaneous EEG waves. No physiological data were collected from the control group. Significant decrements in tracking ability were observed in the chamber crew. The time course of these effects followed a triphasic pattern with initial deterioration, intermediate recovery to pre-isolation baseline scores after the first half of the isolation period, and a second deterioration towards the end. None of the control group subjects displayed such an effect. Memory search (speed and accuracy) was only occasionally impaired during isolation, but the control group displayed a similar pattern of changes. It is suggested that a state of decreased alertness causes tracking deterioration, which leads to a reduced efficiency of sustained cue utilization. The assumption of low alertness was further substantiated by higher fatigue ratings by the chamber crew compared to those of the control group. Analysis of the continuous EEG recordings revealed that only two subjects produced reliable alpha wave activity (8-12 Hz) over Pz and, to a much smaller extent, Fz-theta wave activity (5-7 Hz) during task performance. In both subjects Pz-alpha power decreased consistently under task conditions involving single-task and dual-task tracking. Fz-theta activity was increased more by single-task and dual-task memory search than by single-task tracking. The alpha attenuation appears to be associated with an increasing demand on perceptual cue utilization required by the tracking performance. In one subject marked attenuation of alpha power occurred during the first half of the confinement period, where he also scored the highest fatigue ratings. A striking increase in fronto-central theta activity was observed in the same subject after six weeks of isolation. The change was associated with an efficient rather than a degraded task performance, and a high rating of the item "concentrated" and a low rating of the item "fatigued." This finding supports the hypothesis that the activation state associated with increased fronto-central theta activity accompanies efficient performance of demanding mental tasks. The usefulness of standardized laboratory tasks as monitoring instruments is demonstrated by the direct comparability with results of studies obtained from other relevant research applications using the same tasks. The feasibility of a self-administered integrated psychophysiological assessment of the individual state was illustrated by the nearly complete collection of data. The large number of individual data collected over the entire period permitted application of quantitative single-subject analysis, allowing reliable determination of changes in the individual state in the course of time. It thus appears that this assessment technique can be adapted for in-flight monitoring of astronauts during prolonged spaceflights. Parallel EEG recording can provide relevant supplementary information for diagnosing the individual activation state associated with task performance. The existence of large individual differences in the generation of task-sensitive EEG rhythms forms an important issue for further studies.

--No Title--

Science.gov Websites

; margin-left: auto; margin-right: auto; } .slick-track:before, .slick-track:after { display: table : auto; border: 1px solid transparent; } .slick-arrow.slick-hidden { display: none;

Getting the Bigger Picture With Digital Surveillance

NASA Technical Reports Server (NTRS)

2002-01-01

Through a Space Act Agreement, Diebold, Inc., acquired the exclusive rights to Glenn Research Center's patented video observation technology, originally designed to accelerate video image analysis for various ongoing and future space applications. Diebold implemented the technology into its AccuTrack digital, color video recorder, a state-of- the-art surveillance product that uses motion detection for around-the- clock monitoring. AccuTrack captures digitally signed images and transaction data in real-time. This process replaces the onerous tasks involved in operating a VCR-based surveillance system, and subsequently eliminates the need for central viewing and tape archiving locations altogether. AccuTrack can monitor an entire bank facility, including four automated teller machines, multiple teller lines, and new account areas, all from one central location.

40 CFR 279.74 - Tracking.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 28 2013-07-01 2013-07-01 false Tracking. 279.74 Section 279.74 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) STANDARDS FOR THE MANAGEMENT OF USED OIL Standards for Used Oil Fuel Marketers § 279.74 Tracking. (a) Off...

40 CFR 279.74 - Tracking.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 27 2011-07-01 2011-07-01 false Tracking. 279.74 Section 279.74 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) STANDARDS FOR THE MANAGEMENT OF USED OIL Standards for Used Oil Fuel Marketers § 279.74 Tracking. (a) Off...

40 CFR 279.56 - Tracking.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 28 2012-07-01 2012-07-01 false Tracking. 279.56 Section 279.56 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) STANDARDS FOR THE MANAGEMENT OF USED OIL Standards for Used Oil Processors and Re-Refiners § 279.56 Tracking. (a...

40 CFR 279.74 - Tracking.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 28 2012-07-01 2012-07-01 false Tracking. 279.74 Section 279.74 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) STANDARDS FOR THE MANAGEMENT OF USED OIL Standards for Used Oil Fuel Marketers § 279.74 Tracking. (a) Off...

40 CFR 279.56 - Tracking.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 27 2014-07-01 2014-07-01 false Tracking. 279.56 Section 279.56 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) STANDARDS FOR THE MANAGEMENT OF USED OIL Standards for Used Oil Processors and Re-Refiners § 279.56 Tracking. (a...

40 CFR 279.56 - Tracking.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 28 2013-07-01 2013-07-01 false Tracking. 279.56 Section 279.56 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) STANDARDS FOR THE MANAGEMENT OF USED OIL Standards for Used Oil Processors and Re-Refiners § 279.56 Tracking. (a...

40 CFR 279.56 - Tracking.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 26 2010-07-01 2010-07-01 false Tracking. 279.56 Section 279.56 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) STANDARDS FOR THE MANAGEMENT OF USED OIL Standards for Used Oil Processors and Re-Refiners § 279.56 Tracking. (a...

40 CFR 279.56 - Tracking.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 27 2011-07-01 2011-07-01 false Tracking. 279.56 Section 279.56 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) STANDARDS FOR THE MANAGEMENT OF USED OIL Standards for Used Oil Processors and Re-Refiners § 279.56 Tracking. (a...

40 CFR 279.74 - Tracking.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 27 2014-07-01 2014-07-01 false Tracking. 279.74 Section 279.74 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) STANDARDS FOR THE MANAGEMENT OF USED OIL Standards for Used Oil Fuel Marketers § 279.74 Tracking. (a) Off...

Imaging antimatter with a Micromegas detector

NASA Astrophysics Data System (ADS)

Mäckel, V.; Radics, B.; Dupre, P.; Higaki, H.; Kanai, Y.; Kuroda, N.; Matsuda, Y.; Nagata, Y.; Tajima, M.; Widmann, E.; Yamazaki, Y.

2018-05-01

The ASACUSA collaboration aims at measuring the ground state hyperfine splitting of antihydrogen for probing fundamental symmetries. A cryogenic trap for mixing antiprotons and positrons serves as an antihydrogen source for in-flight spectroscopy. In order to be able to monitor the antihydrogen formation process, a dedicated Micromegas tracking detector has been designed and built to record the annihilation distribution in the trap. In this paper, we present the first results from antiproton annihilation data recorded with the Micromegas, together with a description of the event reconstruction algorithm.

Mesoscale modeling of strain induced solid state amorphization in crystalline materials

NASA Astrophysics Data System (ADS)

Lei, Lei

Solid state amorphization, and in particular crystalline to amorphous transformation, can be observed in metallic alloys, semiconductors, intermetallics, minerals, and also molecular crystals when they undergo irradiation, hydrogen gas dissolution, thermal interdiffusion, mechanical alloying, or mechanical milling. Although the amorphization mechanisms may be different, the transformation occurs due to the high level of disorder introduced into the material. Milling induced solid state amorphization is proposed to be the result of accumulation of crystal defects, specifically dislocations, as the material is subjected to large deformations during the high energy process. Thus, understanding the deformation mechanisms of crystalline materials will be the first step in studying solid state amorphization in crystalline materials, which not only has scientific contributions, but also technical consequences. A phase field dislocation dynamics (PFDD) approach is employed in this work to simulate plastic deformation of molecular crystals. This PFDD model has the advantage of tracking all of the dislocations in a material simultaneously. The model takes into account the elastic interaction between dislocations, the lattice resistance to dislocation motion, and the elastic interaction of dislocations with an external stress field. The PFDD model is employed to describe the deformation of molecular crystals with pharmaceutical applications, namely, single crystal sucrose, acetaminophen, gamma-indomethacin, and aspirin. Stress-strain curves are produced that result in expected anisotropic material response due to the activation of different slip systems and yield stresses that agree well with those from experiments. The PFDD model is coupled to a phase transformation model to study the relation between plastic deformation and the solid state amorphization of crystals that undergo milling. This model predicts the amorphous volume fraction in excellent agreement with experimental observation. Finally, we incorporate the effect of stress free surfaces to model the behavior of dislocations close to these surfaces and in the presence of voids.

A Look at Derailment Today: North America and Europe.

ERIC Educational Resources Information Center

Leslie, Jean Brittain; Van Velsor, Ellen

Executives with a track record of success are sometimes fired, demoted, or plateaued. This publication presents findings of a study conducted by the Center for Creative Leadership (CCL), which compared contemporary derailed and successful executives in the United States and Europe. Results are compared to those of earlier CCL findings. Data were…

77 FR 22663 - Importation of Pomegranates From Chile Under a Systems Approach

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-17

...: Tenuipalpidae) into the commenter's State until a pest-free track record is established in shipments of... cartons or containers that are marked to show the official registration number of the production site... packinghouse and must be packed into new, clean boxes, crates, or other APHIS-approved packing containers. Each...

The Influence of Glove Type on Simulated Wheelchair Racing Propulsion: A Pilot Study.

PubMed

Rice, I; Dysterheft, J; Bleakney, A W; Cooper, R A

2016-01-01

Our purpose was to examine the influence of glove type on kinetic and spatiotemporal parameters at the handrim in elite wheelchair racers. Elite wheelchair racers (n=9) propelled on a dynamometer in their own racing chairs with a force and moment sensing wheel attached. Racers propelled at 3 steady state speeds (5.36, 6.26 & 7.60 m/s) and performed one maximal effort sprint with 2 different glove types (soft & solid). Peak resultant force, peak torque, impulse, contact angle, braking torque, push time, velocity, and stroke frequency were recorded for steady state and sprint conditions. Multiple nonparametric Wilcoxon matched pair's tests were used to detect differences between glove types, while effect sizes were calculated based on Cohen's d. During steady state trials, racers propelled faster, using more strokes and larger contact angle, while applying less impulse with solid gloves compared to soft gloves. During the sprint condition, racers achieved greater top end velocities, applying larger peak force, with less braking torque with solid gloves compared to soft gloves. Use of solid gloves may provide some performance benefits to wheelchair racers during steady state and top end velocity conditions. © Georg Thieme Verlag KG Stuttgart · New York.

Atomic scale dynamics of a solid state chemical reaction directly determined by annular dark-field electron microscopy.

PubMed

Pennycook, Timothy J; Jones, Lewys; Pettersson, Henrik; Coelho, João; Canavan, Megan; Mendoza-Sanchez, Beatriz; Nicolosi, Valeria; Nellist, Peter D

2014-12-22

Dynamic processes, such as solid-state chemical reactions and phase changes, are ubiquitous in materials science, and developing a capability to observe the mechanisms of such processes on the atomic scale can offer new insights across a wide range of materials systems. Aberration correction in scanning transmission electron microscopy (STEM) has enabled atomic resolution imaging at significantly reduced beam energies and electron doses. It has also made possible the quantitative determination of the composition and occupancy of atomic columns using the atomic number (Z)-contrast annular dark-field (ADF) imaging available in STEM. Here we combine these benefits to record the motions and quantitative changes in the occupancy of individual atomic columns during a solid-state chemical reaction in manganese oxides. These oxides are of great interest for energy-storage applications such as for electrode materials in pseudocapacitors. We employ rapid scanning in STEM to both drive and directly observe the atomic scale dynamics behind the transformation of Mn3O4 into MnO. The results demonstrate we now have the experimental capability to understand the complex atomic mechanisms involved in phase changes and solid state chemical reactions.

11% efficiency solid-state dye-sensitized solar cells with copper(II/I) hole transport materials

PubMed Central

Cao, Yiming; Saygili, Yasemin; Ummadisingu, Amita; Teuscher, Joël; Luo, Jingshan; Pellet, Norman; Giordano, Fabrizio; Zakeeruddin, Shaik Mohammed; Moser, Jacques -E.; Freitag, Marina; Hagfeldt, Anders; Grätzel, Michael

2017-01-01

Solid-state dye-sensitized solar cells currently suffer from issues such as inadequate nanopore filling, low conductivity and crystallization of hole-transport materials infiltrated in the mesoscopic TiO2 scaffolds, leading to low performances. Here we report a record 11% stable solid-state dye-sensitized solar cell under standard air mass 1.5 global using a hole-transport material composed of a blend of [Cu (4,4′,6,6′-tetramethyl-2,2′-bipyridine)2](bis(trifluoromethylsulfonyl)imide)2 and [Cu (4,4′,6,6′-tetramethyl-2,2′-bipyridine)2](bis(trifluoromethylsulfonyl)imide). The amorphous Cu(II/I) conductors that conduct holes by rapid hopping infiltrated in a 6.5 μm-thick mesoscopic TiO2 scaffold are crucial for achieving such high efficiency. Using time-resolved laser photolysis, we determine the time constants for electron injection from the photoexcited sensitizers Y123 into the TiO2 and regeneration of the Y123 by Cu(I) to be 25 ps and 3.2 μs, respectively. Our work will foster the development of low-cost solid-state photovoltaic based on transition metal complexes as hole conductors. PMID:28598436

A new role for primary care teams in the United States after “Obamacare:” Track and improve health insurance coverage rates

PubMed Central

DeVoe, Jennifer; Angier, Heather; Hoopes, Megan; Gold, Rachel

2017-01-01

Maintaining continuous health insurance coverage is important. With recent expansions in access to coverage in the United States after “Obamacare,” primary care teams have a new role in helping to track and improve coverage rates and to provide outreach to patients. We describe efforts to longitudinally track health insurance rates using data from the electronic health record (EHR) of a primary care network and to use these data to support practice-based insurance outreach and assistance. Although we highlight a few examples from one network, we believe there is great potential for doing this type of work in a broad range of family medicine and community health clinics that provide continuity of care. By partnering with researchers through practice-based research networks and other similar collaboratives, primary care practices can greatly expand the use of EHR data and EHR-based tools targeting improvements in health insurance and quality health care. PMID:28966926

Earth and ocean dynamics satellites and systems

NASA Technical Reports Server (NTRS)

Vonbun, F. O.

1975-01-01

An overview is presented of the present state of satellite and ground systems making observations of the dynamics of the solid earth and the oceans. Emphasis is placed on applications of space technology for practical use. Topics discussed include: satellite missions and results over the last two decades in the areas of earth gravity field, polar motions, earth tides, magnetic anomalies, and satellite-to-satellite tracking; laser ranging systems; development of the Very Long Baseline Interferometer; and Skylab radar altimeter data applications.

High-speed (20 kHz) digital in-line holography for transient particle tracking and sizing in multiphase flows

DOE PAGES

Guildenbecher, Daniel R.; Cooper, Marcia A.; Sojka, Paul E.

2016-04-05

High-speed (20 kHz) digital in-line holography (DIH) is applied for 3D quantification of the size and velocity of fragments formed from the impact of a single water drop onto a thin film of water and burning aluminum particles from the combustion of a solid rocket propellant. To address the depth-of-focus problem in DIH, a regression-based multiframe tracking algorithm is employed, and out-of-plane experimental displacement accuracy is shown to be improved by an order-of-magnitude. Comparison of the results with previous DIH measurements using low-speed recording shows improved positional accuracy with the added advantage of detailed resolution of transient dynamics from singlemore » experimental realizations. Furthermore, the method is shown to be particularly advantageous for quantification of particle mass flow rates. For the investigated particle fields, the mass flows rates, which have been automatically measured from single experimental realizations, are found to be within 8% of the expected values.« less

Studies on radon/thoron and their decay products in granite quarries around Bangalore city, India

NASA Astrophysics Data System (ADS)

Ningappa, C.; Sannappa, J.; Chandrashekara, M. S.; Paramesh, L.

2009-08-01

The radon survey was performed in granite quarries around Bangalore rural district and Bangalore city as part of a lung cancer epidemiological study. Long duration measurements of indoor and outdoor radon, thoron and their progenies concentrations were made around granite quarries of Bangalore rural district by using Solid State Nuclear Track Detector (SSNTD, LR-115, Type-II Plastic track detector) during summer and winter period (2006-07). The increase of radioactivity in granite quarries and inhalation dose to workers and populations near the quarries have been summarized. The higher concentrations of radon and thoron in granite quarries suggest radiation health effects on workers and public around the quarries is higher than permissible levels. The results are presented and analyzed with reference to ICRP limits.

40 CFR 273.19 - Tracking universal waste shipments.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 27 2011-07-01 2011-07-01 false Tracking universal waste shipments. 273.19 Section 273.19 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID... Universal Waste § 273.19 Tracking universal waste shipments. A small quantity handler of universal waste is...

A Comparison of Multiscale Permutation Entropy Measures in On-Line Depth of Anesthesia Monitoring

PubMed Central

Li, Xiaoli; Li, Duan; Li, Yongwang; Ursino, Mauro

2016-01-01

Objective Multiscale permutation entropy (MSPE) is becoming an interesting tool to explore neurophysiological mechanisms in recent years. In this study, six MSPE measures were proposed for on-line depth of anesthesia (DoA) monitoring to quantify the anesthetic effect on the real-time EEG recordings. The performance of these measures in describing the transient characters of simulated neural populations and clinical anesthesia EEG were evaluated and compared. Methods Six MSPE algorithms—derived from Shannon permutation entropy (SPE), Renyi permutation entropy (RPE) and Tsallis permutation entropy (TPE) combined with the decomposition procedures of coarse-graining (CG) method and moving average (MA) analysis—were studied. A thalamo-cortical neural mass model (TCNMM) was used to generate noise-free EEG under anesthesia to quantitatively assess the robustness of each MSPE measure against noise. Then, the clinical anesthesia EEG recordings from 20 patients were analyzed with these measures. To validate their effectiveness, the ability of six measures were compared in terms of tracking the dynamical changes in EEG data and the performance in state discrimination. The Pearson correlation coefficient (R) was used to assess the relationship among MSPE measures. Results CG-based MSPEs failed in on-line DoA monitoring at multiscale analysis. In on-line EEG analysis, the MA-based MSPE measures at 5 decomposed scales could track the transient changes of EEG recordings and statistically distinguish the awake state, unconsciousness and recovery of consciousness (RoC) state significantly. Compared to single-scale SPE and RPE, MSPEs had better anti-noise ability and MA-RPE at scale 5 performed best in this aspect. MA-TPE outperformed other measures with faster tracking speed of the loss of unconsciousness. Conclusions MA-based multiscale permutation entropies have the potential for on-line anesthesia EEG analysis with its simple computation and sensitivity to drug effect changes. CG-based multiscale permutation entropies may fail to describe the characteristics of EEG at high decomposition scales. PMID:27723803

A Comparison of Multiscale Permutation Entropy Measures in On-Line Depth of Anesthesia Monitoring.

PubMed

Su, Cui; Liang, Zhenhu; Li, Xiaoli; Li, Duan; Li, Yongwang; Ursino, Mauro

2016-01-01

Multiscale permutation entropy (MSPE) is becoming an interesting tool to explore neurophysiological mechanisms in recent years. In this study, six MSPE measures were proposed for on-line depth of anesthesia (DoA) monitoring to quantify the anesthetic effect on the real-time EEG recordings. The performance of these measures in describing the transient characters of simulated neural populations and clinical anesthesia EEG were evaluated and compared. Six MSPE algorithms-derived from Shannon permutation entropy (SPE), Renyi permutation entropy (RPE) and Tsallis permutation entropy (TPE) combined with the decomposition procedures of coarse-graining (CG) method and moving average (MA) analysis-were studied. A thalamo-cortical neural mass model (TCNMM) was used to generate noise-free EEG under anesthesia to quantitatively assess the robustness of each MSPE measure against noise. Then, the clinical anesthesia EEG recordings from 20 patients were analyzed with these measures. To validate their effectiveness, the ability of six measures were compared in terms of tracking the dynamical changes in EEG data and the performance in state discrimination. The Pearson correlation coefficient (R) was used to assess the relationship among MSPE measures. CG-based MSPEs failed in on-line DoA monitoring at multiscale analysis. In on-line EEG analysis, the MA-based MSPE measures at 5 decomposed scales could track the transient changes of EEG recordings and statistically distinguish the awake state, unconsciousness and recovery of consciousness (RoC) state significantly. Compared to single-scale SPE and RPE, MSPEs had better anti-noise ability and MA-RPE at scale 5 performed best in this aspect. MA-TPE outperformed other measures with faster tracking speed of the loss of unconsciousness. MA-based multiscale permutation entropies have the potential for on-line anesthesia EEG analysis with its simple computation and sensitivity to drug effect changes. CG-based multiscale permutation entropies may fail to describe the characteristics of EEG at high decomposition scales.

The High Altitude Balloon Experiment demonstration of acquisition, tracking, and pointing technologies (HABE-ATP)

NASA Astrophysics Data System (ADS)

Dimiduk, D.; Caylor, M.; Williamson, D.; Larson, L.

1995-01-01

The High Altitude Balloon Experiment demonstration of Acquisition, Tracking, and Pointing (HABE-ATP) is a system built around balloon-borne payload which is carried to a nominal 26-km altitude. The goal is laser tracking thrusting theater and strategic missiles, and then pointing a surrogate laser weapon beam, with performance levels end a timeline traceable to operational laser weapon system requirements. This goal leads to an experiment system design which combines hardware from many technology areas: an optical telescope and IR sensors; an advanced angular inertial reference; a flexible multi-level of actuation digital control system; digital tracking processors which incorporate real-time image analysis and a pulsed, diode-pumped solid state tracking laser. The system components have been selected to meet the overall experiment goals of tracking unmodified boosters at 50- 200 km range. The ATP system on HABE must stabilize and control a relative line of sight between the platform and the unmodified target booster to a 1 microrad accuracy. The angular pointing reference system supports both open loop and closed loop track modes; GPS provides absolute position reference. The control system which positions the line of sight for the ATP system must sequence through accepting a state vector handoff, closed-loop passive IR acquisition, passive IR intermediate fine track, active fine track, and then finally aimpoint determination and maintenance modes. Line of sight stabilization to fine accuracy levels is accomplished by actuating wide bandwidth fast steering mirrors (FSM's). These control loops off-load large-amplitude errors to the outer gimbal in order to remain within the limited angular throw of the FSM's. The SWIR acquisition and MWIR intermediate fine track sensors (both PtSi focal planes) image the signature of the rocket plume. After Hard Body Handover (HBHO), active fine tracking is conducted with a visible focal plane viewing the laser-illuminated target rocket body. The track and fire control performance must be developed to the point that an aimpoint can be selected, maintained, and then track performance scored with a low-power 'surrogate' weapon beam. Extensive instrumentation monitors not only the optical sensors and the video data, but all aspects of each of the experiment subsystems such as the control system, the experiment flight vehicle, and the tracker. Because the system is balloon-borne and recoverable, it is expected to fly many times during its development program.

Exponential parameter and tracking error convergence guarantees for adaptive controllers without persistency of excitation

NASA Astrophysics Data System (ADS)

Chowdhary, Girish; Mühlegg, Maximilian; Johnson, Eric

2014-08-01

In model reference adaptive control (MRAC) the modelling uncertainty is often assumed to be parameterised with time-invariant unknown ideal parameters. The convergence of parameters of the adaptive element to these ideal parameters is beneficial, as it guarantees exponential stability, and makes an online learned model of the system available. Most MRAC methods, however, require persistent excitation of the states to guarantee that the adaptive parameters converge to the ideal values. Enforcing PE may be resource intensive and often infeasible in practice. This paper presents theoretical analysis and illustrative examples of an adaptive control method that leverages the increasing ability to record and process data online by using specifically selected and online recorded data concurrently with instantaneous data for adaptation. It is shown that when the system uncertainty can be modelled as a combination of known nonlinear bases, simultaneous exponential tracking and parameter error convergence can be guaranteed if the system states are exciting over finite intervals such that rich data can be recorded online; PE is not required. Furthermore, the rate of convergence is directly proportional to the minimum singular value of the matrix containing online recorded data. Consequently, an online algorithm to record and forget data is presented and its effects on the resulting switched closed-loop dynamics are analysed. It is also shown that when radial basis function neural networks (NNs) are used as adaptive elements, the method guarantees exponential convergence of the NN parameters to a compact neighbourhood of their ideal values without requiring PE. Flight test results on a fixed-wing unmanned aerial vehicle demonstrate the effectiveness of the method.

Flow of Cadmium from Rechargeable Batteries in the United States, 1996-2007

USGS Publications Warehouse

Wilburn, David R.

2007-01-01

Cadmium metal has been found to be toxic to humans and the environment under certain conditions; therefore, a thorough understanding of the use and disposal of the metal is warranted. Most of the cadmium used in the United States comes from imported products. In 2007, more than 83 percent of the cadmium used in the United States was contained in batteries, mostly in rechargeable nickel-cadmium batteries used in popular consumer products such as cordless phones and power tools. The flow of cadmium contained in rechageable nickel-cadmium batteries used in the United States was tracked for the years 1996 to 2007. The amount of cadmium metal contained in imported products in 2007 was estimated to be about 1,900 metric tons, or about 160 percent higher than the reported cadmium production in the United States from all primary and secondary sources. Although more than 40,000 metric tons of cadmium was estimated to be contained in nickel-cadmium rechargeable batteries that became obsolete during the 12-year study period, not all of this material was sent to municipal solid waste landfills. About 27 percent of the material available for recovery in the United States was recycled domestically in 2007; the balance was discarded in municipal solid waste landfills, exported for recycling, retained in temporary storage, or thrown away.

Cholinergic Interneurons Use Orbitofrontal Input to Track Beliefs about Current State.

PubMed

Stalnaker, Thomas A; Berg, Ben; Aujla, Navkiran; Schoenbaum, Geoffrey

2016-06-08

When conditions change, organisms need to learn about the changed conditions without interfering with what they already know. To do so, they can assign the new learning to a new "state" and the old learning to a previous state. This state assignment is fundamental to behavioral flexibility. Cholinergic interneurons (CINs) in the dorsomedial striatum (DMS) are necessary for associative information to be compartmentalized in this way, but the mechanism by which they do so is unknown. Here we addressed this question by recording putative CINs from the DMS in rats performing a task consisting of a series of trial blocks, or states, that required the recall and application of contradictory associative information. We found that individual CINs in the DMS represented the current state throughout each trial. These state correlates were not observed in dorsolateral striatal CINs recorded in the same rats. Notably, DMS CIN ensembles tracked rats' beliefs about the current state such that, when states were miscoded, rats tended to make suboptimal choices reflecting the miscoding. State information held by the DMS CINs also depended completely on the orbitofrontal cortex, an area that has been proposed to signal environmental states. These results suggest that CINs set the stage for recalling associative information relevant to the current environment by maintaining a real-time representation of the current state. Such a role has novel implications for understanding the neural basis of a variety of psychiatric diseases, such as addiction or anxiety disorders, in which patients generalize inappropriately (or fail to generalize) between different environments. Striatal cholinergic interneurons (CINs) are thought to be identical to tonically active neurons. These neurons have long been thought to have an important influence on striatal processing during reward-related learning. Recently, a more specific function for striatal CINs has been suggested, which is that they are necessary for striatal learning to be compartmentalized into different states as the state of the environment changes. Here we report that putative CINs appear to track rats' beliefs about which environmental state is current. We further show that this property of CINs depends on orbitofrontal cortex input and is correlated with choices made by rats. These findings could provide new insight into neuropsychiatric diseases that involve improper generalization between different contexts. Copyright © 2016 the authors 0270-6474/16/366242-16$15.00/0.

First evidence of Hadrosauropodus in Gondwana (Yacoraite Formation, Maastrichtian-Danian), northwestern Argentina

NASA Astrophysics Data System (ADS)

Díaz-Martínez, Ignacio; de Valais, Silvina; Cónsole-Gonella, Carlos

2016-10-01

Uppermost Cretaceous (Campanian-Maastrichtian) large ornithopod tracks are scarce in Gondwana. This record is limited to few citations in the northern Argentina, Peru and possibly Bolivia, although their ichnological affinities are still under discussion. Recently, a new vertebrate tracksite with large ornithopod tracks has been found in the Maimará locality, Jujuy province, Argentina, from the Yacoraite Formation (Maastrichtian-Danian). The best preserved track is characterized by having large and bilobed heel impression and wide and short digit impressions with blunt claw marks. This record represents the unambiguous record of large ornithopod tracks in Gondwana in the Uppermost Cretaceous, and its features allow classifying it as Hadrosauropodus. Previously, this ichnotaxon had exclusively Laurasian distribution. Therefore, this record is the first evidence of Hadrosauropodus from Gondwana expanding the geographic range of this ichnogenus. A member of Hadrosauridae is reinforced as possible trackmaker of the Hadrosauropodus tracks. Uppermost Cretaceous hadrosaurid dinosaurs are scarce in Gondwana, being the record limited to Patagonia, La Pampa province and Antarctica. Therefore, the Maimará tracks increase the knowledge of this kind of dinosaur from Gondwana.

Solid-state framing camera with multiple time frames

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baker, K. L.; Stewart, R. E.; Steele, P. T.

2013-10-07

A high speed solid-state framing camera has been developed which can operate over a wide range of photon energies. This camera measures the two-dimensional spatial profile of the flux incident on a cadmium selenide semiconductor at multiple times. This multi-frame camera has been tested at 3.1 eV and 4.5 keV. The framing camera currently records two frames with a temporal separation between the frames of 5 ps but this separation can be varied between hundreds of femtoseconds up to nanoseconds and the number of frames can be increased by angularly multiplexing the probe beam onto the cadmium selenide semiconductor.

Measurement of DNA translocation dynamics in a solid-state nanopore at 100-ns temporal resolution

PubMed Central

Shekar, Siddharth; Niedzwiecki, David J.; Chien, Chen-Chi; Ong, Peijie; Fleischer, Daniel A.; Lin, Jianxun; Rosenstein, Jacob K.; Drndic, Marija; Shepard, Kenneth L.

2017-01-01

Despite the potential for nanopores to be a platform for high-bandwidth study of single-molecule systems, ionic current measurements through nanopores have been limited in their temporal resolution by noise arising from poorly optimized measurement electronics and large parasitic capacitances in the nanopore membranes. Here, we present a complementary metal-oxide-semiconductor (CMOS) nanopore (CNP) amplifier capable of low noise recordings at an unprecedented 10 MHz bandwidth. When integrated with state-of-the-art solid-state nanopores in silicon nitride membranes, we achieve an SNR of greater than 10 for ssDNA translocations at a measurement bandwidth of 5 MHz, which represents the fastest ion current recordings through nanopores reported to date. We observe transient features in ssDNA translocation events that are as short as 200 ns, which are hidden even at bandwidths as high as 1 MHz. These features offer further insights into the translocation kinetics of molecules entering and exiting the pore. This platform highlights the advantages of high-bandwidth translocation measurements made possible by integrating nanopores and custom-designed electronics. PMID:27332998

The railroad tracks are being repaired at KSC

NASA Technical Reports Server (NTRS)

2000-01-01

The railroad tracks are under repair at Kennedy Space Center. This section of track is located on KSC property, just north of the NASA Causeway in the KSC Industrial Area. The repairs were required following the minor derailment of two solid rocket booster segment cars on July 18.

Sustained multifocal attentional enhancement of stimulus processing in early visual areas predicts tracking performance.

PubMed

Störmer, Viola S; Winther, Gesche N; Li, Shu-Chen; Andersen, Søren K

2013-03-20

Keeping track of multiple moving objects is an essential ability of visual perception. However, the mechanisms underlying this ability are not well understood. We instructed human observers to track five or seven independent randomly moving target objects amid identical nontargets and recorded steady-state visual evoked potentials (SSVEPs) elicited by these stimuli. Visual processing of moving targets, as assessed by SSVEP amplitudes, was continuously facilitated relative to the processing of identical but irrelevant nontargets. The cortical sources of this enhancement were located to areas including early visual cortex V1-V3 and motion-sensitive area MT, suggesting that the sustained multifocal attentional enhancement during multiple object tracking already operates at hierarchically early stages of visual processing. Consistent with this interpretation, the magnitude of attentional facilitation during tracking in a single trial predicted the speed of target identification at the end of the trial. Together, these findings demonstrate that attention can flexibly and dynamically facilitate the processing of multiple independent object locations in early visual areas and thereby allow for tracking of these objects.

21 CFR 821.55 - Confidentiality.

Code of Federal Regulations, 2011 CFR

2011-04-01

... MEDICAL DEVICE TRACKING REQUIREMENTS Records and Inspections § 821.55 Confidentiality. (a) Any patient receiving a device subject to tracking requirements under this part may refuse to release, or refuse... identifying information for the purpose of tracking. (b) Records and other information submitted to FDA under...

Affective Pacman: A Frustrating Game for Brain-Computer Interface Experiments

NASA Astrophysics Data System (ADS)

Reuderink, Boris; Nijholt, Anton; Poel, Mannes

We present the design and development of Affective Pacman, a game that induces frustration to study the effect of user state changes on the EEG signal. Affective Pacman is designed to induce frustration for short periods, and allows the synchronous recording of a wide range of sensors, such as physiological sensors and EEG in addition to the game state. A self-assessment is integrated in the game to track changes in user state. Preliminary results indicate a significant effect of the frustration induction on the EEG.

STED microscopy visualizes energy deposition of single ions in a solid-state detector beyond diffraction limit

NASA Astrophysics Data System (ADS)

Niklas, M.; Henrich, M.; Jäkel, O.; Engelhardt, J.; Abdollahi, A.; Greilich, S.

2017-05-01

Fluorescent nuclear track detectors (FNTDs) allow for visualization of single-particle traversal in clinical ion beams. The point spread function of the confocal readout has so far hindered a more detailed characterization of the track spots—the ion’s characteristic signature left in the FNTD. Here we report on the readout of the FNTD by optical nanoscopy, namely stimulated emission depletion microscopy. It was firstly possible to visualize the track spots of carbon ions and protons beyond the diffraction limit of conventional light microscopy with a resolving power of approximately 80 nm (confocal: 320 nm). A clear discrimination of the spatial width, defined by the full width half maximum of track spots from particles (proton and carbon ions), with a linear energy transfer (LET) ranging from approximately 2-1016 keV µm-1 was possible. Results suggest that the width depends on LET but not on particle charge within the uncertainties. A discrimination of particle type by width thus does not seem possible (as well as with confocal microscopy). The increased resolution, however, could allow for refined determination of the cross-sectional area facing substantial energy deposition. This work could pave the way towards development of optical nanoscopy-based analysis of radiation-induced cellular response using cell-fluorescent ion track hybrid detectors.

Fragmentation studies of relativistic iron ions using plastic nuclear track detectors.

PubMed

Scampoli, P; Durante, M; Grossi, G; Manti, L; Pugliese, M; Gialanella, G

2005-01-01

We measured fluence and fragmentation of high-energy (1 or 5 A GeV) 56Fe ions accelerated at the Alternating Gradient Synchrotron or at the NASA Space Radiation Laboratory (Brookhaven National Laboratory, NY, USA) using solid-state CR-39 nuclear track detectors. Different targets (polyethylene, PMMA, C, Al, Pb) were used to produce a large spectrum of charged fragments. CR-39 plastics were exposed both in front and behind the shielding block (thickness ranging from 5 to 30 g/cm2) at a normal incidence and low fluence. The radiation dose deposited by surviving Fe ions and charged fragments was measured behind the shield using an ionization chamber. The distribution of the measured track size was exploited to distinguish the primary 56Fe ions tracks from the lighter fragments. Measurements of projectile's fluence in front of the shield were used to determine the dose per incident particle behind the block. Simultaneous measurements of primary 56Fe ion tracks in front and behind the shield were used to evaluate the fraction of surviving iron projectiles and the total charge-changing fragmentation cross-section. These physical measurements will be used to characterize the beam used in parallel biological experiments. c2005 COSPAR. Published by Elsevier Ltd. All rights reserved.

Air-Track: a real-world floating environment for active sensing in head-fixed mice.

PubMed

Nashaat, Mostafa A; Oraby, Hatem; Sachdev, Robert N S; Winter, York; Larkum, Matthew E

2016-10-01

Natural behavior occurs in multiple sensory and motor modalities and in particular is dependent on sensory feedback that constantly adjusts behavior. To investigate the underlying neuronal correlates of natural behavior, it is useful to have access to state-of-the-art recording equipment (e.g., 2-photon imaging, patch recordings, etc.) that frequently requires head fixation. This limitation has been addressed with various approaches such as virtual reality/air ball or treadmill systems. However, achieving multimodal realistic behavior in these systems can be challenging. These systems are often also complex and expensive to implement. Here we present "Air-Track," an easy-to-build head-fixed behavioral environment that requires only minimal computational processing. The Air-Track is a lightweight physical maze floating on an air table that has all the properties of the "real" world, including multiple sensory modalities tightly coupled to motor actions. To test this system, we trained mice in Go/No-Go and two-alternative forced choice tasks in a plus maze. Mice chose lanes and discriminated apertures or textures by moving the Air-Track back and forth and rotating it around themselves. Mice rapidly adapted to moving the track and used visual, auditory, and tactile cues to guide them in performing the tasks. A custom-controlled camera system monitored animal location and generated data that could be used to calculate reaction times in the visual and somatosensory discrimination tasks. We conclude that the Air-Track system is ideal for eliciting natural behavior in concert with virtually any system for monitoring or manipulating brain activity. Copyright © 2016 the American Physiological Society.

Air-Track: a real-world floating environment for active sensing in head-fixed mice

PubMed Central

Oraby, Hatem; Sachdev, Robert N. S.; Winter, York

2016-01-01

Natural behavior occurs in multiple sensory and motor modalities and in particular is dependent on sensory feedback that constantly adjusts behavior. To investigate the underlying neuronal correlates of natural behavior, it is useful to have access to state-of-the-art recording equipment (e.g., 2-photon imaging, patch recordings, etc.) that frequently requires head fixation. This limitation has been addressed with various approaches such as virtual reality/air ball or treadmill systems. However, achieving multimodal realistic behavior in these systems can be challenging. These systems are often also complex and expensive to implement. Here we present “Air-Track,” an easy-to-build head-fixed behavioral environment that requires only minimal computational processing. The Air-Track is a lightweight physical maze floating on an air table that has all the properties of the “real” world, including multiple sensory modalities tightly coupled to motor actions. To test this system, we trained mice in Go/No-Go and two-alternative forced choice tasks in a plus maze. Mice chose lanes and discriminated apertures or textures by moving the Air-Track back and forth and rotating it around themselves. Mice rapidly adapted to moving the track and used visual, auditory, and tactile cues to guide them in performing the tasks. A custom-controlled camera system monitored animal location and generated data that could be used to calculate reaction times in the visual and somatosensory discrimination tasks. We conclude that the Air-Track system is ideal for eliciting natural behavior in concert with virtually any system for monitoring or manipulating brain activity. PMID:27486102

Electronic Medical Business Operations System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cannon, D. T.; Metcalf, J. R.; North, M. P.

Electronic Management of medical records has taken a back seat both in private industry and in the government. Record volumes continue to rise every day and management of these paper records is inefficient and very expensive. In 2005, the White House announced support for the development of electronic medical records across the federal government. In 2006, the DOE issued 10 CFR 851 requiring all medical records be electronically available by 2015. The Y-12 National Security Complex is currently investing funds to develop a comprehensive EMR to incorporate the requirements of an occupational health facility which are common across the Nuclearmore » Weapons Complex (NWC). Scheduling, workflow, and data capture from medical surveillance, certification, and qualification examinations are core pieces of the system. The Electronic Medical Business Operations System (EMBOS) will provide a comprehensive health tool solution to 10 CFR 851 for Y-12 and can be leveraged to the Nuclear Weapon Complex (NWC); all site in the NWC must meet the requirements of 10 CFR 851 which states that all medical records must be electronically available by 2015. There is also potential to leverage EMBOS to the private4 sector. EMBOS is being developed and deployed in phases. When fully deployed the EMBOS will be a state-of-the-art web-enabled integrated electronic solution providing a complete electronic medical record (EMR). EMBOS has been deployed and provides a dynamic electronic medical history and surveillance program (e.g., Asbestos, Hearing Conservation, and Respirator Wearer) questionnaire. Table 1 below lists EMBOS capabilities and data to be tracked. Data to be tracked: Patient Demographics – Current/Historical; Physical Examination Data; Employee Medical Health History; Medical Surveillance Programs; Patient and Provider Schedules; Medical Qualification/Certifications; Laboratory Data; Standardized Abnormal Lab Notifications; Prescription Medication Tracking and Dispensing; Allergies; Non-Occupational Illness and Injury Visits; Occupational Recommendations/Restrictions; Diagnosis/Vital Signs/Blood Pressures; Immunizations; Return to Work Visits Capabilities: Targeted Health Assessments; Patient Input Capabilities for Questionnaires; Medical Health History; Surveillance Programs; Human Reliability Program; Scheduling; Automated Patient Check-in/Check-out; Provider & Patient Workflow; Laboratory Interface & Device Integration; Human Reliability Program Processing; Interoperability with SAP, IH, IS, RADCON; Coding: ICED-9/10; Desktop Integration; Interface/Storage of Digital X-Rays (PACS)« less

Modeling of thermal lensing in side and end-pumped finite solid-state laser rods. M.S. Thesis

NASA Technical Reports Server (NTRS)

Brackett, Vincent G.

1990-01-01

An analytical expression for approximating the time-dependent thermal focal length in finite solid state laser rods was derived. The analysis is based on the temperature variation of the material refractive index caused by optical pumping of these rods. Several quantities were found to be relevant to this analysis. These quantities were the specific thermal profiles of the rods, type of optical pumping employed, type of cooling scheme employed (side and end-cooling parameters), and the specific material characteristics of the rods. The Thermal Lensing Model was formulated using the geometric ray tracing approach. The focal lengths are then approximated, by calculating the phase shift in the index of refraction, as the different rays of an incident plane wave are tracked through a lens-like crystal medium. The approach also applies in the case of Gaussian or parabolic pump beams. It is shown that the prediction of thermal focal length is in good quantitative agreement with experimentally obtained data.

Rotary head type reproducing apparatus

DOEpatents

Takayama, Nobutoshi; Edakubo, Hiroo; Kozuki, Susumu; Takei, Masahiro; Nagasawa, Kenichi

1986-01-01

In an apparatus of the kind arranged to reproduce, with a plurality of rotary heads, an information signal from a record bearing medium having many recording tracks which are parallel to each other with the information signal recorded therein and with a plurality of different pilot signals of different frequencies also recorded one by one, one in each of the recording tracks, a plurality of different reference signals of different frequencies are simultaneously generated. A tracking error is detected by using the different reference signals together with the pilot signals which are included in signals reproduced from the plurality of rotary heads.

Flow Mapping in a Gas-Solid Riser via Computer Automated Radioactive Particle Tracking (CARPT)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Muthanna Al-Dahhan; Milorad P. Dudukovic; Satish Bhusarapu

2005-06-04

Statement of the Problem: Developing and disseminating a general and experimentally validated model for turbulent multiphase fluid dynamics suitable for engineering design purposes in industrial scale applications of riser reactors and pneumatic conveying, require collecting reliable data on solids trajectories, velocities ? averaged and instantaneous, solids holdup distribution and solids fluxes in the riser as a function of operating conditions. Such data are currently not available on the same system. Multiphase Fluid Dynamics Research Consortium (MFDRC) was established to address these issues on a chosen example of circulating fluidized bed (CFB) reactor, which is widely used in petroleum and chemicalmore » industry including coal combustion. This project addresses the problem of lacking reliable data to advance CFB technology. Project Objectives: The objective of this project is to advance the understanding of the solids flow pattern and mixing in a well-developed flow region of a gas-solid riser, operated at different gas flow rates and solids loading using the state-of-the-art non-intrusive measurements. This work creates an insight and reliable database for local solids fluid-dynamic quantities in a pilot-plant scale CFB, which can then be used to validate/develop phenomenological models for the riser. This study also attempts to provide benchmark data for validation of Computational Fluid Dynamic (CFD) codes and their current closures. Technical Approach: Non-Invasive Computer Automated Radioactive Particle Tracking (CARPT) technique provides complete Eulerian solids flow field (time average velocity map and various turbulence parameters such as the Reynolds stresses, turbulent kinetic energy, and eddy diffusivities). It also gives directly the Lagrangian information of solids flow and yields the true solids residence time distribution (RTD). Another radiation based technique, Computed Tomography (CT) yields detailed time averaged local holdup profiles at various planes. Together, these two techniques can provide the needed local solids flow dynamic information for the same setup under identical operating conditions, and the data obtained can be used as a benchmark for development, and refinement of the appropriate riser models. For the above reasons these two techniques were implemented in this study on a fully developed section of the riser. To derive the global mixing information in the riser, accurate solids RTD is needed and was obtained by monitoring the entry and exit of a single radioactive tracer. Other global parameters such as Cycle Time Distribution (CTD), overall solids holdup in the riser, solids recycle percentage at the bottom section of the riser were evaluated from different solids travel time distributions. Besides, to measure accurately and in-situ the overall solids mass flux, a novel method was applied.« less

Statistical Physics Experiments Using Dusty Plasmas

NASA Astrophysics Data System (ADS)

Goree, John

2016-10-01

Compared to other areas of physics research, Statistical Physics is heavily dominated by theory, with comparatively little experiment. One reason for the lack of experiments is the impracticality of tracking of individual atoms and molecules within a substance. Thus, there is a need for a different kind of experimental system, one where individual particles not only move stochastically as they collide with one another, but also are large enough to allow tracking. A dusty plasma can meet this need. A dusty plasma is a partially ionized gas containing small particles of solid matter. These micron-size particles gain thousands of electronic charges by collecting more electrons than ions. Their motions are dominated by Coulomb collisions with neighboring particles. In this so-called strongly coupled plasma, the dust particles self-organize in much the same way as atoms in a liquid or solid. Unlike atoms, however, these particles are large and slow, so that they can be tracked easily by video microscopy. Advantages of dusty plasma for experimental statistical physics research include particle tracking, lack of frictional contact with solid surfaces, and avoidance of overdamped motion. Moreover, the motion of a collection of dust particles can mimic an equilibrium system with a Maxwellian velocity distribution, even though the dust particles themselves are not truly in thermal equilibrium. Nonequilibrium statistical physics can be studied by applying gradients, for example by imposing a shear flow. In this talk I will review some of our recent experiments with shear flow. First, we performed the first experimental test to verify the Fluctuation Theorem for a shear flow, showing that brief violations of the Second Law of Thermodynamics occur with the predicted probabilities, for a small system. Second, we discovered a skewness of a shear-stress distribution in a shear flow. This skewness is a phenomenon that likely has wide applicability in nonequilibrium steady states. Third, we performed the first experimental test of a statistical physics theory (the Green-Kubo model) that is widely used by physical chemists to compute viscosity coefficients, and we found that it fails. Work supported by the U.S. Department of Energy, NSF, and NASA.

What Happens to Students Who Take Community College "Dual Enrollment" Courses in High School?

ERIC Educational Resources Information Center

Fink, John; Jenkins, Davis; Yanagiura, Takeshi

2017-01-01

The number of students taking college courses while they are in high school has grown dramatically over the past two decades--particularly at community colleges--but many colleges and states do not track participants' outcomes. Using student enrollment and degree records from the National Student Clearinghouse, this report is the first to look…

A Statistical Approach For Modeling Tropical Cyclones. Synthetic Hurricanes Generator Model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pasqualini, Donatella

This manuscript brie y describes a statistical ap- proach to generate synthetic tropical cyclone tracks to be used in risk evaluations. The Synthetic Hur- ricane Generator (SynHurG) model allows model- ing hurricane risk in the United States supporting decision makers and implementations of adaptation strategies to extreme weather. In the literature there are mainly two approaches to model hurricane hazard for risk prediction: deterministic-statistical approaches, where the storm key physical parameters are calculated using physi- cal complex climate models and the tracks are usually determined statistically from historical data; and sta- tistical approaches, where both variables and tracks are estimatedmore » stochastically using historical records. SynHurG falls in the second category adopting a pure stochastic approach.« less

Evaluation of the measurement uncertainty when measuring the resistance of solid isolating materials to tracking

NASA Astrophysics Data System (ADS)

Stare, E.; Beges, G.; Drnovsek, J.

2006-07-01

This paper presents the results of research into the measurement of the resistance of solid isolating materials to tracking. Two types of tracking were investigated: the proof tracking index (PTI) and the comparative tracking index (CTI). Evaluation of the measurement uncertainty in a case study was performed using a test method in accordance with the IEC 60112 standard. In the scope of the tests performed here, this particular test method was used to ensure the safety of electrical appliances. According to the EN ISO/IEC 17025 standard (EN ISO/IEC 17025), in the process of conformity assessment, the evaluation of the measurement uncertainty of the test method should be carried out. In the present article, possible influential parameters that are in accordance with the third and fourth editions of the standard IEC 60112 are discussed. The differences, ambiguities or lack of guidance referring to both editions of the standard are described in the article 'Ambiguities in technical standards—case study IEC 60112—measuring the resistance of solid isolating materials to tracking' (submitted for publication). Several hundred measurements were taken in the present experiments in order to form the basis for the results and conclusions presented. A specific problem of the test (according to the IEC 60112 standard) is the great variety of influential physical parameters (mechanical, electrical, chemical, etc) that can affect the results. At the end of the present article therefore, there is a histogram containing information on the contributions to the measurement uncertainty.

A USA Commercial Flight Track Database for Upper Tropospheric Aircraft Emission Studies

NASA Technical Reports Server (NTRS)

Garber, Donald P.; Minnis, Patrick; Costulis, Kay P.

2003-01-01

A new air traffic database over the contiguous United States of America (USA) has been developed from a commercially available real-time product for 2001-2003 for all non-military flights above 25,000 ft. Both individual flight tracks and gridded spatially integrated flight legs are available. On average, approximately 24,000 high-altitude flights were recorded each day. The diurnal cycle of air traffic over the USA is characterized by a broad daytime maximum with a 0130-LT minimum and a mean day-night air traffic ratio of 2.4. Each week, the air traffic typically peaks on Thursday and drops to a low Saturday with a range of 18%. Flight density is greatest during late summer and least during winter. The database records the disruption of air traffic after the air traffic shutdown during September 2001. The dataset should be valuable for realistically simulating the atmospheric effects of aircraft in the upper troposphere.

Experiment for validation of fluid-structure interaction models and algorithms.

PubMed

Hessenthaler, A; Gaddum, N R; Holub, O; Sinkus, R; Röhrle, O; Nordsletten, D

2017-09-01

In this paper a fluid-structure interaction (FSI) experiment is presented. The aim of this experiment is to provide a challenging yet easy-to-setup FSI test case that addresses the need for rigorous testing of FSI algorithms and modeling frameworks. Steady-state and periodic steady-state test cases with constant and periodic inflow were established. Focus of the experiment is on biomedical engineering applications with flow being in the laminar regime with Reynolds numbers 1283 and 651. Flow and solid domains were defined using computer-aided design (CAD) tools. The experimental design aimed at providing a straightforward boundary condition definition. Material parameters and mechanical response of a moderately viscous Newtonian fluid and a nonlinear incompressible solid were experimentally determined. A comprehensive data set was acquired by using magnetic resonance imaging to record the interaction between the fluid and the solid, quantifying flow and solid motion. Copyright © 2016 The Authors. International Journal for Numerical Methods in Biomedical Engineering published by John Wiley & Sons Ltd.

¹³C solid-state NMR analysis of the most common pharmaceutical excipients used in solid drug formulations, Part I: Chemical shifts assignment.

PubMed

Pisklak, Dariusz Maciej; Zielińska-Pisklak, Monika Agnieszka; Szeleszczuk, Łukasz; Wawer, Iwona

2016-04-15

Solid-state NMR is an excellent and useful method for analyzing solid-state forms of drugs. In the (13)C CP/MAS NMR spectra of the solid dosage forms many of the signals originate from the excipients and should be distinguished from those of active pharmaceutical ingredient (API). In this work the most common pharmaceutical excipients used in the solid drug formulations: anhydrous α-lactose, α-lactose monohydrate, mannitol, sucrose, sorbitol, sodium starch glycolate type A and B, starch of different origin, microcrystalline cellulose, hypromellose, ethylcellulose, methylcellulose, hydroxyethylcellulose, sodium alginate, magnesium stearate, sodium laurilsulfate and Kollidon(®) were analyzed. Their (13)C CP/MAS NMR spectra were recorded and the signals were assigned, employing the results (R(2): 0.948-0.998) of GIPAW calculations and theoretical chemical shifts. The (13)C ssNMR spectra for some of the studied excipients have not been published before while for the other signals in the spectra they were not properly assigned or the assignments were not correct. The results summarize and complement the data on the (13)C ssNMR analysis of the most common pharmaceutical excipients and are essential for further NMR studies of API-excipient interactions in the pharmaceutical formulations. Copyright © 2016 Elsevier B.V. All rights reserved.

FT-IR and FT-Raman spectra of 5-chlorocytosine: Solid state simulation and tautomerism. Effect of the chlorine substitution in the Watson-Crick base pair 5-chlorodeoxycytidine-deoxyguanosine

NASA Astrophysics Data System (ADS)

Alcolea Palafox, M.; Rastogi, V. K.; Singh, S. P.

2018-01-01

The laser Raman and IR spectra of 5-chlorocytosine have been recorded and accurately assigned in the solid state using Density functional calculations (DFT) together with the linear scaling equation procedure (LSE) and the solid state simulation of the crystal unit cell through a tetramer form. These results remarkably improve those reported previously by other authors. Several new scaling equations were proposed to be used in related molecules. The six main tautomers of the biomolecule 5-chlorocytosine were determined and optimized at the MP2 and CCSD levels, using different basis sets. The relative stabilities were compared with those obtained in cytosine and their 5-halo derivatives. Several relationships between energies, geometric parameters and NBO atomic charges were established. The effect of the chlorine substitution in the fifth position was evaluated through the stability of the Watson-Crick (WC) base pair of 5-chlorodeoxycytidine with deoxyguanosine, and through their vibrational spectra.

Bacteriophage Tail-Tube Assembly Studied by Proton-Detected 4D Solid-State NMR

DOE PAGES

Zinke, Maximilian; Fricke, Pascal; Samson, Camille; ...

2017-07-07

Obtaining unambiguous resonance assignments remains a major bottleneck in solid-state NMR studies of protein structure and dynamics. Particularly for supramolecular assemblies with large subunits (>150 residues), the analysis of crowded spectral data presents a challenge, even if three-dimensional (3D) spectra are used. Here, we present a proton-detected 4D solid-state NMR assignment procedure that is tailored for large assemblies. The key to recording 4D spectra with three indirect carbon or nitrogen dimensions with their inherently large chemical shift dispersion lies in the use of sparse non-uniform sampling (as low as 2 %). As a proof of principle, we acquired 4D (H)COCANH,more » (H)CACONH, and (H)CBCANH spectra of the 20 kDa bacteriophage tail-tube protein gp17.1 in a total time of two and a half weeks. These spectra were sufficient to obtain complete resonance assignments in a straightforward manner without use of previous solution NMR data.« less

Bacteriophage Tail-Tube Assembly Studied by Proton-Detected 4D Solid-State NMR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zinke, Maximilian; Fricke, Pascal; Samson, Camille

Obtaining unambiguous resonance assignments remains a major bottleneck in solid-state NMR studies of protein structure and dynamics. Particularly for supramolecular assemblies with large subunits (>150 residues), the analysis of crowded spectral data presents a challenge, even if three-dimensional (3D) spectra are used. Here, we present a proton-detected 4D solid-state NMR assignment procedure that is tailored for large assemblies. The key to recording 4D spectra with three indirect carbon or nitrogen dimensions with their inherently large chemical shift dispersion lies in the use of sparse non-uniform sampling (as low as 2 %). As a proof of principle, we acquired 4D (H)COCANH,more » (H)CACONH, and (H)CBCANH spectra of the 20 kDa bacteriophage tail-tube protein gp17.1 in a total time of two and a half weeks. These spectra were sufficient to obtain complete resonance assignments in a straightforward manner without use of previous solution NMR data.« less

Identifying health facilities outside the enterprise: challenges and strategies for supporting health reform and meaningful use.

PubMed

Dixon, Brian E; Colvard, Cyril; Tierney, William M

2014-06-24

Objective: To support collation of data for disability determination, we sought to accurately identify facilities where care was delivered across multiple, independent hospitals and clinics. Methods: Data from various institutions' electronic health records were merged and delivered as continuity of care documents to the United States Social Security Administration (SSA). Results: Electronic records for nearly 8000 disability claimants were exchanged with SSA. Due to the lack of standard nomenclature for identifying the facilities in which patients received the care documented in the electronic records, SSA could not match the information received with information provided by disability claimants. Facility identifiers were generated arbitrarily by health care systems and therefore could not be mapped to the existing international standards. Discussion: We propose strategies for improving facility identification in electronic health records to support improved tracking of a patient's care between providers to better serve clinical care delivery, disability determination, health reform and meaningful use. Conclusion: Accurately identifying the facilities where health care is delivered to patients is important to a number of major health reform and improvement efforts underway in many nations. A standardized nomenclature for identifying health care facilities is needed to improve tracking of care and linking of electronic health records.

Fe(II)-induced transformation from ferrihydrite to lepidocrocite and goethite

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu Hui; Institute of Coal Chemistry, Chinese Academy of Sciences, Taiyuan 030001 China; Li Ping

2007-07-15

The transformation of Fe(II)-adsorbed ferrihydrite was studied. Data tracking the formation of products as a function of pH, temperature and time is presented. The results indicate that trace of Fe(II) adsorbed on ferrihydrite can accelerate its transformation obviously. The products are lepidocrocite and/or goethite and/or hematite, which is different from those without Fe(II). That is, Fe(II) not only accelerates the transformation of ferrihydrite but also leads to the formation of lepidocrocite by a new path. The behavior of Fe(II) is shown in two aspects-catalytic dissolution-reprecipitation and catalytic solid-state transformation. The results indicate that a high temperature and a high pH(inmore » the range from 5 to 9) are favorable to solid-state transformation and the formation of hematite, while a low temperature and a low pH are favorable to dissolution-reprecipitation mechanism and the formation of lepidocrocite. Special attentions were given to the formation mechanism of lepidocrocite and goethite. - Graphical abstract: Fe(II)-adsorbed ferrihydrite can rapidly transform into lepidocrocite or/and goethite or/and hematite. Which product dominates depends on the transformation conditions of ferrihydrite such as temperature, pH, reaction time, etc. In the current system, there exist two transformation mechanisms. One is dissolution/reprecipitation and the other is solid-state transformation. The transformation mechanisms from Fe(II)-adsorbed ferrihydrite to lepidocrocite and goethite were investigated.« less

Storing Data and Video on One Tape

NASA Technical Reports Server (NTRS)

Nixon, J. H.; Cater, J. P.

1985-01-01

Microprocessor-based system originally developed for anthropometric research merges digital data with video images for storage on video cassette recorder. Combined signals later retrieved and displayed simultaneously on television monitor. System also extracts digital portion of stored information and transfers it to solid-state memory.

Simulation of zones of contribution to wells at site GM–38, Naval Weapons Industrial Reserve Plant, Bethpage, New York

USGS Publications Warehouse

Misut, Paul

2014-01-01

A three-dimensional groundwater-flow model is coupled with the particle-tracking program MODPATH to delineate zones of contribution to wells pumping from the Magothy aquifer and supplying water to a chlorinated volatile organic compound removal plant at site GM–38, Naval Weapons Industrial Reserve Plant, Bethpage, New York. By use of driller’s logs, a transitional probability approach generated three alternative realizations of heterogeneity within the Magothy aquifer to assess uncertainty in model representation. Finer-grained sediments with low hydraulic conductivity were realized as laterally discontinuous, thickening towards the south, and comprising about 17 percent of the total aquifer volume. Particle-tracking evaluations of a steady state present conditions model with alternative heterogeneity realizations were used to develop zones of contribution of remedial pumping wells. Because of heterogeneity and high rates of advection within the coarse-grained sediments, transport by dispersion and (or) diffusion was assumed to be negligible. Resulting zones of contribution of existing remedial wells are complex shapes, influenced by heterogeneity of each realization and other nearby hydrologic stresses. The use of two particle tracking techniques helped identify zones of contribution to wells. Backtracking techniques and observations of points of intersection of backward-tracked particles at shells of the GM–38 Hot Spot, as defined by surfaces of equal total volatile organic compound concentration, identified the source of water within the GM–38 Hot Spot to simulated wells. Forward-tracking techniques identified the fate of water within the GM–38 Hot Spot, including well capture and discharge to model constant head and drain boundaries. The percentage of backward-tracked particles, started at GM–38 wells that were sourced from within the Hot Spot, varied from 72.0 to 98.2, depending on the Hot Spot delineation used (present steady state model and Magothy aquifer heterogeneity realization A). The percentage of forward-tracked particles that were captured by GM–38 wells varied from 81.1 to 94.6, depending on the Hot Spot delineation used, with the remainder primarily captured by Bethpage Water District Plant 4 production wells (present steady state model and Magothy aquifer heterogeneity realization A). Less than 1 percent of forward-tracked particles ultimately discharge at model constant head and drain boundaries. The differences between forward- and backward-tracked particle percentage ranges are due to some forward-tracked particles not being captured by GM–38 wells, and some backward-tracked particles not intersecting specific regions of the Hot Spot. During 2013, an aquifer test generated detailed time series of well pumping rates and corresponding water-level responses were recorded at numerous locations. These data were used to verify the present conditions steady state model and demonstrate the sensitivity of model results to transient-state changes.

Tracking Vaccination Teams During Polio Campaigns in Northern Nigeria by Use of Geographic Information System Technology: 2013-2015.

PubMed

Touray, Kebba; Mkanda, Pascal; Tegegn, Sisay G; Nsubuga, Peter; Erbeto, Tesfaye B; Banda, Richard; Etsano, Andrew; Shuaib, Faisal; Vaz, Rui G

2016-05-01

Nigeria is among the 3 countries in which polio remains endemic. The country made significant efforts to reduce polio transmission but remains challenged by poor-quality campaigns and poor team performance in some areas. This article demonstrates the application of geographic information system technology to track vaccination teams to monitor settlement coverage, reduce the number of missed settlements, and improve team performance. In each local government area where tracking was conducted, global positioning system-enabled Android phones were given to each team on a daily basis and were used to record team tracks. These tracks were uploaded to a dashboard to show the level of coverage and identify areas missed by the teams. From 2012 to June 2015, tracking covered 119 immunization days. A total of 1149 tracking activities were conducted. Of these, 681 (59%) were implemented in Kano state. There was an improvement in the geographic coverage of settlements and an overall reduction in the number of missed settlements. The tracking of vaccination teams provided significant feedback during polio campaigns and enabled supervisors to evaluate performance of vaccination teams. The reports supported other polio program activities, such as review of microplans and the deployment of other interventions, for increasing population immunity in northern Nigeria. © 2016 World Health Organization; licensee Oxford Journals.

TH-AB-202-07: Radar Tracking of Respiratory Motion in Real Time

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fung, A; Li, C; Torres, C

Purpose: To propose a method of real time tracking of respiratory motion in patients undergoing radiation therapy. Radar technology can be employed to detection the movement of diaphragm and thoracic anatomy. Methods: A radar transceiver was specially designed. During experiment, the radar device was securely attached to a fixed frame. Respiratory motion was simulated with: 1) Varian RPM phantom, 2) Standard Imaging Respiratory Gating Platform. Signals recorded with radar equipment were compared with those measured with Varian RPM system as a reference. Results: Motion generated by Varian RPM phantom was recorded by the radar device, and compared to the signalsmore » recorded by RPM camera. The results showed exact agreement between the two monitoring equipments. Motion was also generated by Standard Imaging Respiratory Motion Platform. The results showed the radar device was capable of measuring motion of various amplitudes and periods. Conclusion: The proposed radar device is able to measure movements such as respiratory motion. Compared to state-of-the-art respiratory detection instrument, the radar device is shown to be equally precise and effective for monitoring respiration in radiation oncology patients.« less

FT-IR spectra of the anti-HIV nucleoside analogue d4T (Stavudine). Solid state simulation by DFT methods and scaling by different procedures

NASA Astrophysics Data System (ADS)

Alcolea Palafox, M.; Kattan, D.; Afseth, N. K.

2018-04-01

A theoretical and experimental vibrational study of the anti-HIV d4T (stavudine or Zerit) nucleoside analogue was carried out. The predicted spectra in the three most stable conformers in the biological active anti-form of the isolated state were compared. Comparison of the conformers with those of the natural nucleoside thymidine was carried out. The calculated spectra were scaled by using different scaling procedures and three DFT methods. The TLSE procedure leads to the lowest error and is thus recommended for scaling. With the population of these conformers the IR gas-phase spectra were predicted. The crystal unit cell of the different polymorphism forms of d4T were simulated through dimer forms by using DFT methods. The scaled spectra of these dimer forms were compared. The FT-IR spectrum was recorded in the solid state in the 400-4000 cm-1 range. The respective vibrational bands were analyzed and assigned to different normal modes of vibration by comparison with the scaled vibrational values of the different dimer forms. Through this comparison, the polymorphous form of the solid state sample was identified. The study indicates that d4T exist only in the ketonic form in the solid state. The results obtained were in agreement with those determined in related anti-HIV nucleoside analogues.

Feasibility of utilizing a commercial eye tracker to assess electronic health record use during patient simulation.

PubMed

Gold, Jeffrey Allen; Stephenson, Laurel E; Gorsuch, Adriel; Parthasarathy, Keshav; Mohan, Vishnu

2016-09-01

Numerous reports describe unintended consequences of electronic health record implementation. Having previously described physicians' failures to recognize patient safety issues within our electronic health record simulation environment, we now report on our use of eye and screen-tracking technology to understand factors associated with poor error recognition during an intensive care unit-based electronic health record simulation. We linked performance on the simulation to standard eye and screen-tracking readouts including number of fixations, saccades, mouse clicks and screens visited. In addition, we developed an overall Composite Eye Tracking score which measured when, where and how often each safety item was viewed. For 39 participants, the Composite Eye Tracking score correlated with performance on the simulation (p = 0.004). Overall, the improved performance was associated with a pattern of rapid scanning of data manifested by increased number of screens visited (p = 0.001), mouse clicks (p = 0.03) and saccades (p = 0.004). Eye tracking can be successfully integrated into electronic health record-based simulation and provides a surrogate measure of cognitive decision making and electronic health record usability. © The Author(s) 2015.

Satellite-tracking and Earth dynamics research programs

NASA Technical Reports Server (NTRS)

1983-01-01

Tracking of LAGEOS for polar motion and Earth rotation studies and for other geophysical investigations, including crustal dynamics, Earth and ocean tides, and the general development of precision orbit determination continues. The BE-C and Starlette satellites were tracked for refined determinations of station coordinates and the Earth's gravity field and for studies of solid Earth dynamics.

Solid state laser communications in space (SOLACOS) high data rate satellite communication system verification program

NASA Astrophysics Data System (ADS)

Pribil, Klaus; Flemmig, Joerg

1994-09-01

This paper gives an overview on the current development status of the SOLACOS program and presents the highlights of the program. SOLACOS (Solid State Laser Communications in Space) is the national German program to develop a high performance laser communication system for high data rate transmission between LEO and GEO satellites (Inter Orbit Link, IOL). Two experimental demonstrator terminals are designed and developed in the SOLACOS program. The main development objectives are the Pointing Acquisition and Tracking subsystem (PAT) and the high data rate communication system. All key subsystems and components are straightway developed to be upgraded in follow- on projects to full space qualification. The main design objective for the system is a high degree of modularity which allows to easily upgrade the system with new upcoming technologies. Therefore, all main subsystems are interconnected via fibers to ease replacement of subsystems. The system implements an asymmetric data link with a 650 MBit/s return channel and a 10 MBit/s forward channel. The 650 MBit/s channel is based on a diode pumped Nd:YAG, Integrated Optics Modulator and uses the syncbit transmission scheme. In the syncbit system synchronization information which is necessary to maintain phase lock of the local oscillator of the coherent receiver is transmitted time multiplexed into the data stream. The PAT system comprises two beam detection sensors and three beam steering elements. For initial acquisition and tracking of the remote satellite a high speed CCD camera with an integrated image processing unit, the Acquisition and Tracking Sensor (ATS) is used. In the tacking mode the beam position is sensed via the Fibernutator sensor which is also used to couple the incoming signal into the receiver fiber. Incoming and outgoing beams are routed through the telescopes which are positioned with a 2 axis gimbal mechanism and a high speed beam steering mirror. The PAT system is controlled by a digital signal processor. For beam control advanced PAT algorithms are under development.

Visual Data Mining: An Exploratory Approach to Analyzing Temporal Patterns of Eye Movements

ERIC Educational Resources Information Center

Yu, Chen; Yurovsky, Daniel; Xu, Tian

2012-01-01

Infant eye movements are an important behavioral resource to understand early human development and learning. But the complexity and amount of gaze data recorded from state-of-the-art eye-tracking systems also pose a challenge: how does one make sense of such dense data? Toward this goal, this article describes an interactive approach based on…

Decohesion Elements using Two and Three-Parameter Mixed-Mode Criteria

NASA Technical Reports Server (NTRS)

Davila, Carlos G.; Camanho, Pedro P.

2001-01-01

An eight-node decohesion element implementing different criteria to predict delamination growth under mixed-mode loading is proposed. The element is used at the interface between solid finite elements to model the initiation and propagation of delamination. A single displacement-based damage parameter is used in a softening law to track the damage state of the interface. The power law criterion and a three-parameter mixed-mode criterion are used to predict delamination growth. The accuracy of the predictions is evaluated in single mode delamination and in the mixed-mode bending tests.

Laser induced fluorescence technique for environmental applications

NASA Astrophysics Data System (ADS)

Utkin, Andrei B.; Felizardo, Rui; Gameiro, Carla; Matos, Ana R.; Cartaxana, Paulo

2014-08-01

We discuss the development of laser induced fluorescence sensors and their application in the evaluation of water pollution and physiological status of higher plants and algae. The sensors were built on the basis of reliable and robust solid-state Nd:YAG lasers. They demonstrated good efficiency in: i) detecting and characterizing oil spills and dissolved organic matter; ii) evaluating the impact of stress on higher plants (cork oak, maritime pine, and genetically modified Arabidopsis); iii) tracking biomass changes in intertidal microphytobenthos; and iv) mapping macroalgal communities in the Tagus Estuary.

Special features of high-speed interaction of supercavitating solids in water

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ishchenko, Aleksandr, E-mail: ichan@niipmm.tsu.ru; Afanas’eva, Svetlana, E-mail: s.a.afanasyeva@mail.ru; Burkin, Viktor, E-mail: v.v.burkin@mail.ru

Special features of material behavior of a supercavitating projectile are investigated at various initial velocities of entering water on the basis of the developed stress-strain state model with possibility of destruction of solids when moving in water and interacting with various underwater barriers with the use of consistent methodological approach of mechanics of continuous media. The calculation-experimental method was used to study the modes of motion of supercavitating projectiles at sub- and supersonic velocities in water medium after acceleration in the barrelled accelerator, as well as their interaction with barriers. Issues of stabilization of the supercavitating projectile on the initialmore » flight path in water were studied. Microphotographs of state of solids made of various materials, before and after interaction with water, at subsonic and supersonic velocities were presented. Supersonic velocity of the supercavitating projectile motion in water of 1590 m/s was recorded.« less

Special features of high-speed interaction of supercavitating solids in water

NASA Astrophysics Data System (ADS)

Ishchenko, Aleksandr; Akinshin, Ruslan; Afanas'eva, Svetlana; Borisenkov, Igor; Burkin, Viktor; Diachkovskii, Aleksei; Korolkov, Leonid; Moiseev, Dmitrii; Khabibullin, Marat

2016-01-01

Special features of material behavior of a supercavitating projectile are investigated at various initial velocities of entering water on the basis of the developed stress-strain state model with possibility of destruction of solids when moving in water and interacting with various underwater barriers with the use of consistent methodological approach of mechanics of continuous media. The calculation-experimental method was used to study the modes of motion of supercavitating projectiles at sub- and supersonic velocities in water medium after acceleration in the barrelled accelerator, as well as their interaction with barriers. Issues of stabilization of the supercavitating projectile on the initial flight path in water were studied. Microphotographs of state of solids made of various materials, before and after interaction with water, at subsonic and supersonic velocities were presented. Supersonic velocity of the supercavitating projectile motion in water of 1590 m/s was recorded.

Integration of an On-Axis General Sun-Tracking Formula in the Algorithm of an Open-Loop Sun-Tracking System

PubMed Central

Chong, Kok-Keong; Wong, Chee-Woon; Siaw, Fei-Lu; Yew, Tiong-Keat; Ng, See-Seng; Liang, Meng-Suan; Lim, Yun-Seng; Lau, Sing-Liong

2009-01-01

A novel on-axis general sun-tracking formula has been integrated in the algorithm of an open-loop sun-tracking system in order to track the sun accurately and cost effectively. Sun-tracking errors due to installation defects of the 25 m2 prototype solar concentrator have been analyzed from recorded solar images with the use of a CCD camera. With the recorded data, misaligned angles from ideal azimuth-elevation axes have been determined and corrected by a straightforward changing of the parameters' values in the general formula of the tracking algorithm to improve the tracking accuracy to 2.99 mrad, which falls below the encoder resolution limit of 4.13 mrad. PMID:22408483

A potential application to the study of microscopic energy deposition in a solid by means of heavy charged-particle induced photochromic alterations in a tissue-equivalent matrix

NASA Astrophysics Data System (ADS)

Emfietzoglou, D.; Moscovitch, M.

1999-01-01

A theoretical study was carried out to investigate the feasibility of using the radiation-induced colour decay of photochromic molecules embedded in a polymer matrix as a probe for studying the microscopic energy deposition of heavy charged particles (HCPs) in a tissue-equivalent solid. The theoretical treatment makes use of the radial dose distribution function as derived from gas-phase physics, together with the effects of the increase in temperature and of matrix degradation on the colour-decay kinetics of the photochromic molecules, according to empirical models derived for the solid state. Bearing in mind the non-stochastic nature of the model, the use of gas-phase physics at the level of radiation interaction, and the fact that some empirical quantities used have been established macroscopically, all factors which signify that extra caution is required in the interpretation of the results, it is shown that when the optimum information retrieval time (after track formation) is considered the technique may be able to resolve differences in the energy deposition pattern by different HCPs in the nanometre range (1-10 nm; material's mass density ) from the track axis. Most importantly, though, the present study aims to erect a theoretical framework for the possible application of the technique and to highlight those aspects which are likely to be critical to its practical usage, such as particle type and energy range, and spatial scale and magnitude of the expected effect together with its dependence on time, the physical characteristics of the matrix, and the kinetic behaviour of the type of photochromic molecule studied. Furthermore, it establishes a rationale for interpreting the experimentally observed (if available) colour changes in the HCP track in terms of the microscopic distribution of energy deposition in it.

Kinetics of propagation of the lattice excitation in a swift heavy ion track

NASA Astrophysics Data System (ADS)

Lipp, V. P.; Volkov, A. E.; Sorokin, M. V.; Rethfeld, B.

2011-05-01

In this research we verify the applicability of the temperature and heat diffusion conceptions for the description of subpicosecond lattice excitations in nanometric tracks of swift heavy ions (SHI) decelerated in solids in the electronic stopping regime. The method is based on the molecular dynamics (MD) analysis of temporal evolutions of the local kinetic and configurational temperatures of a lattice. We used solid argon as the model system. MD simulations demonstrated that in a SHI track (a) thermalization of lattice excitations takes time of several picoseconds, and (b) application of the parabolic heat diffusion equations for the description of spatial and temporal propagation of lattice excitations is questionable at least up to 10 ps after the ion passage.

Acoustic tracking of sperm whales in the Gulf of Alaska using a two-element vertical array and tags.

PubMed

Mathias, Delphine; Thode, Aaron M; Straley, Jan; Andrews, Russel D

2013-09-01

Between 15 and 17 August 2010, a simple two-element vertical array was deployed off the continental slope of Southeast Alaska in 1200 m water depth. The array was attached to a vertical buoy line used to mark each end of a longline fishing set, at 300 m depth, close to the sound-speed minimum of the deep-water profile. The buoy line also served as a depredation decoy, attracting seven sperm whales to the area. One animal was tagged with both a LIMPET dive depth-transmitting satellite and bioacoustic "B-probe" tag. Both tag datasets were used as an independent check of various passive acoustic schemes for tracking the whale in depth and range, which exploited the elevation angles and relative arrival times of multiple ray paths recorded on the array. Analytical tracking formulas were viable up to 2 km range, but only numerical propagation models yielded accurate locations up to at least 35 km range at Beaufort sea state 3. Neither localization approach required knowledge of the local bottom bathymetry. The tracking system was successfully used to estimate the source level of an individual sperm whale's "clicks" and "creaks" and predict the maximum detection range of the signals as a function of sea state.

Solid-state NMR calculations for metal oxides and gallates: Shielding and quadrupolar parameters for perovskites and related phases

NASA Astrophysics Data System (ADS)

Middlemiss, Derek S.; Blanc, Frédéric; Pickard, Chris J.; Grey, Clare P.

2010-05-01

The NMR parameters obtained from solid-state DFT calculations within the GIPAW approach for 17O- and 69/71Ga-sites in a range of predominantly oxide-based (group II monoxides, SrTiO 3, BaZrO 3, BaSnO 3, BaTiO 3, LaAlO 3, LaGaO 3, SrZrO 3, MgSiO 3 and Ba 2In 2O 5), and gallate (α- and β-Ga 2O 3, LiGaO 2, NaGaO 2, GaPO 4 and LaGaO 3) materials are compared with experimental values, with a view to the future application of a similar approach to doped phases of interest as candidate intermediate temperature solid oxide fuel cell (ITSOFC) electrolytes. Isotropic and anisotropic chemical shift parameters, quadrupolar coupling constants, and associated asymmetries are presented and analyzed. The unusual GaO 5 site occurring in LaGaGe 2O 7 is also fully characterised. In general, it is found that the theoretical results closely track the experimental trends, though some deviations are identified and discussed, particularly in regard to quadrupolar ηQ-values. The high quality of the computed results suggests that this approach can be extended to study more complex and disordered phases.

Space Shuttle Star Tracker Challenges

NASA Technical Reports Server (NTRS)

Herrera, Linda M.

2010-01-01

The space shuttle fleet of avionics was originally designed in the 1970's. Many of the subsystems have been upgraded and replaced, however some original hardware continues to fly. Not only fly, but has proven to be the best design available to perform its designated task. The shuttle star tracker system is currently flying as a mixture of old and new designs, each with a unique purpose to fill for the mission. Orbiter missions have tackled many varied missions in space over the years. As the orbiters began flying to the International Space Station (ISS), new challenges were discovered and overcome as new trusses and modules were added. For the star tracker subsystem, the growing ISS posed an unusual problem, bright light. With two star trackers on board, the 1970's vintage image dissector tube (IDT) star trackers track the ISS, while the new solid state design is used for dim star tracking. This presentation focuses on the challenges and solutions used to ensure star trackers can complete the shuttle missions successfully. Topics include KSC team and industry partner methods used to correct pressurized case failures and track system performance.

Tracking arousal state and mind wandering with pupillometry.

PubMed

Unsworth, Nash; Robison, Matthew K

2018-04-13

In four experiments, the association between arousal state and different mind-wandering states was examined. Participants performed a sustained attention task while pupil responses were continuously recorded. Periodically during the task, participants were presented with thought probes to determine if they were on task or mind wandering. Across the four experiments, the results suggested that in situations that promoted on-task behaviors and focused external attention, mind wandering was associated with lowered arousal, as seen by smaller tonic pupil diameters and smaller phasic pupillary responses. However, in situations that promoted a more internal focus of attention, there were no differences between on-task states and mind wandering in tonic pupil diameter (although differences emerged for phasic pupillary responses), suggesting similar arousal levels. Furthermore, across the four experiments, mind blanking and mind wandering dissociated in terms of whether the situation promoted focused external attention or focused internal attention. These results are broadly consistent with the notion that mind wandering is a heterogeneous construct, with different forms of mind wandering being associated with different arousal states, and suggest that a combination of behavioral and pupillary measures can be used to track these various states.

77 FR 67348 - Privacy Act of 1974; System of Records-Alternative Dispute Resolution (ADR) Center Case Tracking...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-09

... J2EE application that is platform independent and captures all information relating to Alternative Dispute Resolution case processing. It tracks, manages, and reports on all data, events, and procedures... records to indicate that it will be used: (1) To track, manage, and report on all data, events, and...

Electronic differential for tramcar bogies: system development and performance evaluation by means of numerical simulation

NASA Astrophysics Data System (ADS)

Barbera, Andrea N.; Bucca, Giuseppe; Corradi, Roberto; Facchinetti, Alan; Mapelli, Ferdinando

2014-05-01

The dynamic behaviour of railway vehicles depends on the wheelset configuration, i.e. solid axle wheelset or independently rotating wheels (IRWs). The self-centring behaviour, peculiar of the solid axle wheelset, makes this kind of wheelset very suitable for tangent track running at low speed: the absence of the self-centring mechanism in the IRWs may lead to anomalous wheel/rail wear, reduced vehicle safety and passengers' discomfort. On the contrary, during negotiation of the sharp curves typical of urban tramways, solid axle wheelsets produce lateral contact forces higher than those of IRWs. This paper illustrates an electronic differential system to be applied to tramcar bogies equipped with wheel-hub motors which allows switching from solid axle in tangent track to IRWs in sharp curve (and vice versa). An electro-mechanical vehicle model is adopted for the design of the control system and for the evaluation of the vehicle dynamic performances.

Using extant taxa to inform studies of fossil footprints

NASA Astrophysics Data System (ADS)

Falkingham, Peter; Gatesy, Stephen

2016-04-01

Attempting to use the fossilized footprints of extinct animals to study their palaeobiology and palaeoecology is notoriously difficult. The inconvenient extinction of the trackmaker makes direct correlation between footprints and foot far from straightforward. However, footprints are the only direct evidence of vertebrate motion recorded in the fossil record, and are potentially a source of data on palaeobiology that cannot be obtained from osteological remains alone. Our interests lie in recovering information about the movements of dinosaurs from their tracks. In particular, the Hitchcock collection of early Jurassic tracks held at the Beneski Museum of Natural History, Amherst, provide a rare look into the 3D form of tracks at and below the surface the animal walked on. Breaking naturally along laminations into 'track books', the specimens present sediment deformation at multiple levels, and in doing so record more of the foot's motion than a single surface might. In order to utilize this rich information source to study the now extinct trackmakers, the process of track formation must be understood at a fundamental level; the interaction of the moving foot and compliant substrate. We used bi-planar X-ray techniques (X-ray Reconstruction of Moving Morphology) to record the limb and foot motions of a Guineafowl traversing both granular and cohesive substrates. This data was supplemented with photogrammetric records of the resultant track surfaces, as well as the motion of metal beads within the sediment, to provide a full experimental dataset of foot and footprint formation. The physical experimental data was used to generate computer simulations of the process using high performance computing and the Discrete Element Method. The resultant simulations showed excellent congruence with reality, and enabled visualization within the sediment volume, and throughout the track-forming process. This physical and virtual experimental set-up has provided major insight into how to interpret the track-books within the Amherst Collection, and as such begin to understand how these early Jurassic dinosaurs moved. More broadly, this complete view of track formation afforded by experimental techniques will aid in interpretation of fossil vertebrate tracks throughout the fossil record.

Using state-issued identification cards for obesity tracking.

PubMed

Morris, Daniel S; Schubert, Stacey S; Ngo, Duyen L; Rubado, Dan J; Main, Eric; Douglas, Jae P

2015-01-01

Obesity prevention has emerged as one of public health's top priorities. Public health agencies need reliable data on population health status to guide prevention efforts. Existing survey data sources provide county-level estimates; obtaining sub-county estimates from survey data can be prohibitively expensive. State-issued identification cards are an alternate data source for community-level obesity estimates. We computed body mass index for 3.2 million adult Oregonians who were issued a driver license or identification card between 2003 and 2010. Statewide estimates of obesity prevalence and average body mass index were compared to the Oregon Behavioral Risk Factor Surveillance System (BRFSS). After geocoding addresses we calculated average adult body mass index for every census tract and block group in the state. Sub-county estimates reveal striking patterns in the population's weight status. Annual obesity prevalence estimates from identification cards averaged 18% lower than the BRFSS for men and 31% lower for women. Body mass index estimates averaged 2% lower than the BRFSS for men and 5% lower for women. Identification card records are a promising data source to augment tracking of obesity. People do tend to misrepresent their weight, but the consistent bias does not obscure patterns and trends. Large numbers of records allow for stable estimates for small geographic areas. Copyright © 2014 Asian Oceanian Association for the Study of Obesity. All rights reserved.

49 CFR 237.155 - Documents and records.

Code of Federal Regulations, 2010 CFR

2010-10-01

... the information required by this part; (3) The track owner monitors its electronic records database...; (4) The track owner shall train its employees who use the system on the proper use of the electronic...

[Neutron Dosimetry System Using CR-39 for High-energy X-ray Radiation Therapy].

PubMed

Yabuta, Kazutoshi; Monzen, Hajime; Tamura, Masaya; Tsuruta, Takao; Itou, Tetsuo; Nohtomi, Akihiro; Nishimura, Yasumasa

2014-01-01

Neutrons are produced during radiation treatment by megavolt X-ray energies. However, it is difficult to measure neutron dose especially just during the irradiation. Therefore, we have developed a system for measuring neutrons with the solid state track detector CR-39, which is free from the influence of the X-ray beams. The energy spectrum of the neutrons was estimated by a Monte Carlo simulation method, and the estimated neutron dose was corrected by the contribution ratio of each energy. Pit formation rates of CR-39 ranged from 2.3 x 10(-3) to 8.2 x 10(-3) for each detector studied. According to the estimated neutron energy spectrum, the energy values for calibration were 144 keV and 515keV, and the contribution ratios were approximately 40:60 for 10 MV photons and 20:70 for photons over 15 MV. Neutron doses measured in the center of a high-energy X-ray field were 0.045 mSv/Gy for a 10 MV linear accelerator and 0.85 mSv/Gy for a 20 MV linear accelerator. We successfully developed the new neutron dose measurement system using the solid track detector, CR-39. This on-time neutron measurement system allows users to measure neutron doses produced in the radiation treatment room more easily.

Collisional, radiative and total electron interaction in compound semiconductor detectors and solid state nuclear track detectors: effective atomic number and electron density.

PubMed

Kurudirek, Murat; Kurudirek, Sinem V

2015-05-01

Effective atomic numbers, Zeff and electron densities, Ne are widely used for characterization of interaction processes in radiation related studies. A variety of detectors are employed to detect different types of radiations i.e. photons and charged particles. In the present work, some compound semiconductor detectors (CSCD) and solid state nuclear track detectors (SSNTD) were investigated with respect to the partial as well as total electron interactions. Zeff and Ne of the given detectors were calculated for collisional, radiative and total electron interactions in the kinetic energy region 10keV-1GeV. Maximum values of Zeff and Ne were observed at higher kinetic energies of electrons. Significant variations in Zeff and Ne up to ≈20-25% were noticed for the detectors, GaN, ZnO, Amber and CR-39 for total electron interaction. Moreover, the obtained Zeff and Ne for electrons were compared to those obtained for photons in the entire energy region. Significant variations in Zeff were also noted not only for photons (up to ≈40% for GaN) but also between photons and electrons (up to ≈60% for CR-39) especially at lower energies. Except for the lower energies, Zeff and Ne keep more or less constant values for the given materials. The energy regions where Zeff and Ne keep constant clearly show the availability of using these parameters for characterization of the materials with respect to the radiation interaction processes. Copyright © 2015 Elsevier Ltd. All rights reserved.

Measurement of 238U and 232Th in Petrol, Gas-oil and Lubricant Samples by Using Nuclear Track Detectors and Resulting Radiation Doses to the Skin of Mechanic Workers.

PubMed

Misdaq, M A; Chaouqi, A; Ouguidi, J; Touti, R; Mortassim, A

2015-10-01

Workers in repair shops of vehicles (cars, buses, truck, etc.) clean carburetors, check fuel distribution, and perform oil changes and greasing. To explore the exposure pathway of (238)U and (232)Th and its decay products to the skin of mechanic workers, these radionuclides were measured inside petrol, gas-oil, and lubricant material samples by means of CR-39 and LR-115 type II solid state nuclear track detectors (SSNTDs), and corresponding annual committed equivalent doses to skin were determined. The maximum total equivalent effective dose to skin due to the (238)U and (232)Th series from the application of different petrol, gas-oil, and lubricant samples by mechanic workers was found equal to 1.2 mSv y(-1) cm(-2).

Heat transfer model and finite element formulation for simulation of selective laser melting

NASA Astrophysics Data System (ADS)

Roy, Souvik; Juha, Mario; Shephard, Mark S.; Maniatty, Antoinette M.

2017-10-01

A novel approach and finite element formulation for modeling the melting, consolidation, and re-solidification process that occurs in selective laser melting additive manufacturing is presented. Two state variables are introduced to track the phase (melt/solid) and the degree of consolidation (powder/fully dense). The effect of the consolidation on the absorption of the laser energy into the material as it transforms from a porous powder to a dense melt is considered. A Lagrangian finite element formulation, which solves the governing equations on the unconsolidated reference configuration is derived, which naturally considers the effect of the changing geometry as the powder melts without needing to update the simulation domain. The finite element model is implemented into a general-purpose parallel finite element solver. Results are presented comparing to experimental results in the literature for a single laser track with good agreement. Predictions for a spiral laser pattern are also shown.

Influence of canopy closure and shrub coverage on travel along coarse woody debris by Eastern chipmunks (Tamias striatus)

Treesearch

Patrick A. Zollner; Kevin J. Crane

2003-01-01

We investigated relationships between canopy closure, shrub cover and the use of coarse woody debris as a travel path by eastern chipmunks (Tamias striatus) in the north central United States. Fine scale movements of chipmunks were followed with tracking spools and the percentage of each movement path directly along coarse woody debris was recorded...

Peterson's Top Colleges for Science: A Guide to Leading Four-Year Programs in the Biological, Chemical, Geological, Mathematical, and Physical Sciences.

ERIC Educational Resources Information Center

Davis-Van Atta, David, Ed.

This guide, published for the first time, provides prospective college students detailed information on 190 United States colleges and universities identified as having very strong track records in the sciences and mathematics. Following a description of how institutions were identified for inclusion by David Davis-Van Atta, and a discussion on…

MEASURING PROJECTOR

DOEpatents

Franck, J.V.; Broadhead, P.S.; Skiff, E.W.

1959-07-14

A semiautomatic measuring projector particularly adapted for measurement of the coordinates of photographic images of particle tracks as prcduced in a bubble or cloud chamber is presented. A viewing screen aids the operator in selecting a particle track for measurement. After approximate manual alignment, an image scanning system coupled to a servo control provides automatic exact alignment of a track image with a reference point. The apparatus can follow along a track with a continuous motion while recording coordinate data at various selected points along the track. The coordinate data is recorded on punched cards for subsequent computer calculation of particle trajectory, momentum, etc.

Accomplishments and Compromises in Prediction Research for World Records and Best Performances in Track and Field and Swimming

ERIC Educational Resources Information Center

Liu, Yuanlong; Paul, Stanley; Fu, Frank H.

2012-01-01

The conductors of this study reviewed prediction research and studied the accomplishments and compromises in predicting world records and best performances in track and field and swimming. The results of the study showed that prediction research only promises to describe the historical trends in track and field and swimming performances, to study…

Tracking Vaccination Teams During Polio Campaigns in Northern Nigeria by Use of Geographic Information System Technology: 2013–2015

PubMed Central

Touray, Kebba; Mkanda, Pascal; Tegegn, Sisay G.; Nsubuga, Peter; Erbeto, Tesfaye B.; Banda, Richard; Etsano, Andrew; Shuaib, Faisal; Vaz, Rui G.

2016-01-01

Introduction. Nigeria is among the 3 countries in which polio remains endemic. The country made significant efforts to reduce polio transmission but remains challenged by poor-quality campaigns and poor team performance in some areas. This article demonstrates the application of geographic information system technology to track vaccination teams to monitor settlement coverage, reduce the number of missed settlements, and improve team performance. Methods. In each local government area where tracking was conducted, global positioning system–enabled Android phones were given to each team on a daily basis and were used to record team tracks. These tracks were uploaded to a dashboard to show the level of coverage and identify areas missed by the teams. Results. From 2012 to June 2015, tracking covered 119 immunization days. A total of 1149 tracking activities were conducted. Of these, 681 (59%) were implemented in Kano state. There was an improvement in the geographic coverage of settlements and an overall reduction in the number of missed settlements. Conclusions. The tracking of vaccination teams provided significant feedback during polio campaigns and enabled supervisors to evaluate performance of vaccination teams. The reports supported other polio program activities, such as review of microplans and the deployment of other interventions, for increasing population immunity in northern Nigeria. PMID:26609004

A 13C NMR study of the structure of four cinnamic acids and their methyl esters

NASA Astrophysics Data System (ADS)

Silva, A. M. S.; Alkorta, I.; Elguero, J.; Silva, V. L. M.

2001-09-01

The 13C NMR spectra, both in DMSO solution and in the solid state of four cinnamic acids (p-methoxy, p-hydroxy, p-methyl, p-chloro) and their corresponding methyl esters have been recorded. The two main results in the solid state are: (i) the only significant difference between acids and esters chemical shifts concerns the Cdbnd O group which, on average, appears at 173 ppm in the acids and 168 ppm in the esters; (ii) the signals of the ortho and meta carbons both in the acids and the esters are splitted. The two 'anomalies' disappear in DMSO solution. These observations can be rationalized using simple GIAO/B3LYP/6-31G∗ calculations.

Ultra-High Density Holographic Memory Module with Solid-State Architecture

NASA Technical Reports Server (NTRS)

Markov, Vladimir B.

2000-01-01

NASA's terrestrial. space, and deep-space missions require technology that allows storing. retrieving, and processing a large volume of information. Holographic memory offers high-density data storage with parallel access and high throughput. Several methods exist for data multiplexing based on the fundamental principles of volume hologram selectivity. We recently demonstrated that a spatial (amplitude-phase) encoding of the reference wave (SERW) looks promising as a way to increase the storage density. The SERW hologram offers a method other than traditional methods of selectivity, such as spatial de-correlation between recorded and reconstruction fields, In this report we present the experimental results of the SERW-hologram memory module with solid-state architecture, which is of particular interest for space operations.

Tactical reconnaissance recorder alternatives

NASA Astrophysics Data System (ADS)

Klang, Mark R.

1997-11-01

The actual collection of data, such as digital imagery, using the multitude of sensors available today and in the near future, requires a high data rate digital recorder. The amount of memory, data rates, environmental factors and affordability are important issues when selecting the type of recording system. This paper will discuss two types of systems, tape and solid state. Emphasis will be placed on operational factors and specific mission profiles that are associated with a tactical reconnaissance mission. The current and projected costs of the digital tape recorder and soli state recorder will be examined. The logistics of moving the data from the aircraft to a Ground Exploitation System will be discussed. Once the data is collected it needs to be stored in non-volatile memory with easy access. One of the major problems encountered during Desert Storm was the inability to locate and retrieve reconnaissance images. A data base that can store terabytes of data and have the ability to recall this information from off-site locations should be a requirement for a Desert Storm scenario.

78 FR 48642 - Privacy Act Systems of Records; Phytosanitary Certificate Issuance and Tracking System

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-09

... [Docket No. APHIS-2012-0104] Privacy Act Systems of Records; Phytosanitary Certificate Issuance and... records is the Phytosanitary Certificate Issuance and Tracking System, USDA-APHIS-13. This notice is... methods: Federal eRulemaking Portal: Go to http://www.regulations.gov/#!documentDetail ;D=APHIS-2012-0104...

78 FR 37775 - Privacy Act Systems of Records; Phytosanitary Certificate Issuance and Tracking System

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-24

... of Records; Phytosanitary Certificate Issuance and Tracking System AGENCY: Animal and Plant Health... to the Privacy Act of 1974, as amended. The system of records is the Phytosanitary Certificate...: You may submit comments by either of the following methods: Federal eRulemaking Portal: Go to http...

76 FR 65535 - Privacy Act of 1974; System of Records

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-21

...) and 72 FR 3410 (Jan. 25, 2007)). TURK is the method by which the FBI tracks the workload of its... supervision of the FBI who are required to keep track of workload in TURK, including: Special Agents... function related to these records. Paper records are stored in locked GSA-approved storage containers...

Privacy Act System of Records: Confidential Business Information Tracking System, EPA-20

EPA Pesticide Factsheets

Learn about the Confidential Business Information Tracking System, including who is covered in the system, the purpose of data collection, routine uses for the system's records, and other security procedures.

40 CFR 279.46 - Tracking.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 26 2010-07-01 2010-07-01 false Tracking. 279.46 Section 279.46 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) STANDARDS FOR THE MANAGEMENT OF USED OIL Standards for Used Oil Transporter and Transfer Facilities § 279.46...

40 CFR 279.46 - Tracking.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 28 2013-07-01 2013-07-01 false Tracking. 279.46 Section 279.46 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) STANDARDS FOR THE MANAGEMENT OF USED OIL Standards for Used Oil Transporter and Transfer Facilities § 279.46...

40 CFR 279.46 - Tracking.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 27 2014-07-01 2014-07-01 false Tracking. 279.46 Section 279.46 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) STANDARDS FOR THE MANAGEMENT OF USED OIL Standards for Used Oil Transporter and Transfer Facilities § 279.46...

40 CFR 279.46 - Tracking.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 28 2012-07-01 2012-07-01 false Tracking. 279.46 Section 279.46 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) STANDARDS FOR THE MANAGEMENT OF USED OIL Standards for Used Oil Transporter and Transfer Facilities § 279.46...

40 CFR 279.46 - Tracking.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 27 2011-07-01 2011-07-01 false Tracking. 279.46 Section 279.46 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) STANDARDS FOR THE MANAGEMENT OF USED OIL Standards for Used Oil Transporter and Transfer Facilities § 279.46...

Subfossil mammalian tracks (Flandrian) in the Severn Estuary, S. W. Britain: mechanics of formation, preservation and distribution

PubMed Central

Allen, J. R. L.

1997-01-01

Mammalian tracks and trackways are widely preserved at all stratigraphical levels in the Flandrian sediments of tidal mudflat and marsh origins which formed over the last 8000–9000 years on the marginal wetlands of the inner Bristol Channel and Severn Estuary. The fauna recorded in this way, however, is less diverse than that known from the few, small assemblages of skeletal remains, including some from archaeological sites, so far assessed. Missing or rarely represented in terms of tracks are the smaller of the large mammals. Humans are represented by tracks throughout the Flandrian deposits. In the earlier Flandrian, they were accompanied by deer and aurochs which gave way, in the later Flandrian, to domesticated cattle and sheep/goat; there are sporadic indications of the presence of horse. Wolf/dog, represented by just two records, is the only smaller large mammal so far recorded as a track. The tracks were made, modified, and eventually preserved under a wide variety of sedimentological conditions on the margins of the estuary. Those environmental conditions constrained the quality of the anatomical evidence preserved in the tracks but can be inferred from the character of the tracks. Field experiments suggest that the moisture content of the sediment at the time was crucial to the general nature of the tracks. The mudflat–marsh silts which received the tracks varied from semi-liquid to firm, depending on tidal and seasonal factors and on the elevation of the sedimentary surface relative to the tidal frame. Some tracks were made in marsh peats which offered little resistance. Deep tracks preserving little detail were produced in weak sediments of high moisture content; tracks formed in strong, firm muds retained full anatomical detail. Referring to mechanical theory, and to a series of laboratory experiments using plasticine, the act of making a track is shown to be similar in character and effect to the indentation of an ideal elastic–plastic material by a punch. The punch represents the descending limb of the animal, the face of the punch the sole of the animal's foot, and the elastic–plastic material the sediment which is pierced and deformed by the downward action of the limb. The character of the experimental tracks, and the range and relative size of the deformation structures they include, is qualitatively similar to what is recorded from the field. Many of the tracks recorded from the field were variously modified in a changeable and dynamic environment before final burial and preservation.

Controlling alpha tracks registration in Makrofol DE 1-1 detector

NASA Astrophysics Data System (ADS)

Hassan, N. M.; Hanafy, M. S.; Naguib, A.; El-Saftawy, A. A.

2017-09-01

Makrofol DE 1-1 is a recent type of solid state nuclear track detectors could be used to measure radon concentration in the environment throughout the detection of α-particles emitted from radon decay. Thus, studying the physical parameters that control the formation of alpha tracks is vital for environmental radiation protection. Makrofol DE 1-1 polycarbonate detector was irradiated by α-particles of energies varied from 2 to 5 MeV emitted from the 241Am source of α-particle energy of 5.5 MeV. Then, the detector was etched in an optimum etching solution of mixed ethyl alcohol in KOH aqueous solution of (85% (Vol.) of 6 M KOH + 15% (Vol.) C2H5OH) at 50 °C for 3 h. Afterward, the bulk etch rate, etching sensitivity, and the registration efficiency of the detector, which control the tracks registration, were measured. The bulk etch rate of Makrofol detector was found to be 3.71 ± 0.71 μm h-1. The etching sensitivity and the detector registration efficiency were decreased exponentially with α-particles' energies following Bragg curve. A precise registration of α-particle was presented in this study. Therefore, Makrofol DE 1-1 can be applied as a radiation dosimeter as well as radon and thoron monitors.

Stress-induced solid-state amorphization of nanocrystalline Ni and NiZr investigated by atomistic simulations

NASA Astrophysics Data System (ADS)

Meraj, Md.; Deng, Chuang; Pal, Snehanshu

2018-01-01

In this study, the feasibility of stress induced solid-state amorphization (SSA) of nanocrystalline (NC) Ni and NiZr alloys having ˜10 nm grain size has been investigated under constant tensile load (uniaxial and triaxial) via molecular dynamics simulations. In order to track the structural evaluation in both NC Ni and NiZr alloys during the SSA process, various types of analysis have been used, including simulated X-ray diffraction, centro-symmetry parameter, Voronoi cluster, common neighbor analysis, and radial distribution function. It is found that SSA in both NC Ni and NiZr alloys can only be achieved under triaxial loading conditions, and the hydrostatic tensile stress required for SSA is significantly lower when at. % Zr is increased in the NC NiZr alloy. Specifically, SSA in NC Ni and Ni-5 at. % Zr alloy was observed only when the temperature and hydrostatic tensile stress reached 800 K and 6 GPa, while SSA could occur in NC Ni-10 at. % Zr alloy under just 2 GPa of hydrostatic tensile stress at 300 K.

Tetrapod tracks in Permo-Triassic eolian beds of southern Brazil (Paraná Basin).

PubMed

Francischini, Heitor; Dentzien-Dias, Paula; Lucas, Spencer G; Schultz, Cesar L

2018-01-01

Tetrapod tracks in eolianites are widespread in the fossil record since the late Paleozoic. Among these ichnofaunas, the ichnogenus Chelichnus is the most representative of the Permian tetrapod ichnological record of eolian deposits of Europe, North America and South America, where the Chelichnus Ichnofacies often occurs. In this contribution, we describe five sets of tracks (one of which is preserved in cross-section), representing the first occurrence of Dicynodontipus and Chelichnus in the "Pirambóia Formation" of southern Brazil. This unit represents a humid desert in southwestern Pangea and its lower and upper contacts lead us to consider its age as Lopingian-Induan. The five sets of tracks studied were compared with several ichnotaxa and body fossils with appendicular elements preserved, allowing us to attribute these tracks to dicynodonts and other indeterminate therapsids. Even though the "Pirambóia Formation" track record is sparse and sub-optimally preserved, it is an important key to better understand the occupation of arid environments by tetrapods across the Permo-Triassic boundary.

Software Assists in Extensive Environmental Auditing

NASA Technical Reports Server (NTRS)

Callac, Christopher; Matherne, Charlie

2002-01-01

The Base Enivronmental Management System (BEMS) is a Web-based application program for managing and tracking audits by the Environmental Office of Stennis Space Center in conformity with standard 14001 of the International Organization for Standardization (ISO 14001). (This standard specifies requirements for an environmental-management system.) BEMS saves time by partly automating what were previously manual processes for creating audit checklists; recording and tracking audit results; issuing, tracking, and implementing corrective-action requests (CARs); tracking continuous improvements (CIs); and tracking audit results and statistics. BEMS consists on an administration module and an auditor module. As its name suggests, the administration module is used to administer the audit. It helps administrators to edit the list of audit questions; edit the list of audit locations; assign manditory questions to locations; track, approve, and edit CARs; and edit completed audits. The auditor module is used by auditors to perform audits and record audit results: It helps the auditors to create audit checklists, complete audits, view completed audits, create CARs, record and acknowledge CIs, and generate reports from audit results.

Software Assists in Extensive Environmental Auditing

NASA Technical Reports Server (NTRS)

Callac, Christopher; Matherne, Charlie

2003-01-01

The Base Environmental Management System (BEMS) is a Web-based application program for managing and tracking audits by the Environmental Office of Stennis Space Center in conformity with standard 14001 of the International Organization for Standardization (ISO 14001). (This standard specifies requirements for an environmental-management system.) BEMS saves time by partly automating what were previously manual processes for creating audit checklists; recording and tracking audit results; issuing, tracking, and implementing corrective-action requests (CARs); tracking continuous improvements (CIs); and tracking audit results and statistics. BEMS consists of an administration module and an auditor module. As its name suggests, the administration module is used to administer the audit. It helps administrators to edit the list of audit questions; edit the list of audit locations; assign mandatory questions to locations; track, approve, and edit CARs; and edit completed audits. The auditor module is used by auditors to perform audits and record audit results: it helps the auditors to create audit checklists, complete audits, view completed audits, create CARs, record and acknowledge CIs, and generate reports from audit results.

Software Assists in Extensive Environmental Auditing

NASA Technical Reports Server (NTRS)

Callac, Christopher; Matherne, Charlie; Selinsky, T.

2002-01-01

The Base Environmental Management System (BEMS) is a Web-based application program for managing and tracking audits by the Environmental Office of Stennis Space Center in conformity with standard 14001 of the International Organization for Standardization (ISO 14001). (This standard specifies requirements for an environmental-management system.) BEMS saves time by partly automating what were previously manual processes for creating audit checklists; recording and tracking audit results; issuing, tracking, and implementing corrective-action requests (CARs); tracking continuous improvements (CIs); and tracking audit results and statistics. BEMS consists of an administration module and an auditor module. As its name suggests, the administration module is used to administer the audit. It helps administrators to edit the list of audit questions; edit the list of audit locations; assign mandatory questions to locations; track, approve, and edit CARs; and edit completed audits. The auditor module is used by auditors to perform audits and record audit results: it helps the auditors to create audit checklists, complete audits, view completed audits, create CARs, record and acknowledge CIs, and generate reports from audit results.

Beyond the Compositional Threshold of Nanoparticle-Based Materials.

PubMed

Portehault, David; Delacroix, Simon; Gouget, Guillaume; Grosjean, Rémi; Chan-Chang, Tsou-Hsi-Camille

2018-04-17

The design of inorganic nanoparticles relies strongly on the knowledge from solid-state chemistry not only for characterization techniques, but also and primarily for choosing the systems that will yield the desired properties. The range of inorganic solids reported and studied as nanoparticles is however strikingly narrow when compared to the solid-state chemistry portfolio of bulk materials. Efforts to enlarge the collection of inorganic particles are becoming increasingly important for three reasons. First, they can yield materials more performing than current ones for a range of fields including biomedicine, optics, catalysis, and energy. Second, looking outside the box of common compositions is a way to target original properties or to discover genuinely new behaviors. The third reason lies in the path followed to reach these novel nano-objects: exploration and setup of new synthetic approaches. Indeed, willingness to access original nanoparticles faces a synthetic challenge: how to reach nanoparticles of solids that originally belong to the realm of solid-state chemistry and its typical protocols at high temperature? To answer this question, alternative reaction pathways must be sought, which may in turn provide tracks for new, untargeted materials. The corresponding strategies require limiting particle growth by confinement at high temperatures or by decreasing the synthesis temperature. Both approaches, especially the latter, provide a nice playground to discover metastable solids never reported before. The aim of this Account is to raise attention to the topic of the design of new inorganic nanoparticles. To do so, we take the perspective of our own work in the field, by first describing synthetic challenges and how they are addressed by current protocols. We then use our achievements to highlight the possibilities offered by new nanomaterials and to introduce synthetic approaches that are not in the focus of recent literature but hold, in our opinion, great promise. We will span methods of low temperature "chimie douce" aqueous synthesis coupled to microwave heating, sol-gel chemistry and processing coupled to solid state reactions, and then molten salt synthesis. These protocols pave the way to metastable low valence oxyhydroxides, vanadates, perovskite oxides, boron carbon nitrides, and metal borides, all obtained at the nanoscale with structural and morphological features differing from "usual" nanomaterials. These nano-objects show original properties, from sensing, thermoelectricity, charge and spin transports, photoluminescence, and catalysis, which require advanced characterization of surface states. We then identify future trends of synthetic methodologies that will merit further attention in this burgeoning field, by emphasizing the importance of unveiling reaction mechanisms and coupling experiments with modeling.

Effect of pseudoephedrine on 800-m-run times of female collegiate track athletes.

PubMed

Berry, Caroline; Wagner, Dale R

2012-09-01

Pseudoephedrine (PSE) is an over-the-counter decongestant that might have ergogenic effects. The World Anti-Doping Agency has prohibited large doses (>150 μg/mL) of PSE, while the National College Athletic Association (NCAA) does not include it on their banned-substance list. This study examined the effect of body-weight dosing of PSE on 800-m-run times of NCAA female runners. Fifteen NCAA female track athletes volunteered to participate in the randomized, double-blind, crossover design. Participants were given 2.5 mg/kg PSE or placebo in trials separated by a week. Ninety minutes postingestion, participants completed an 800-m individual time trial on an indoor track. Finishing time was recorded with an automated video timing device. Heart rate and anxiety state scores were recorded immediately after each trial. Fourteen runners completed both trials, and 1 was an outlier: N=13. Despite the dose being well above normal therapeutic levels (144±17 mg), there was no significant difference (P=.92) in 800-m times between PSE (2:39.447±9.584) and placebo (2:39.372±9.636) trials, in postexercise heart rate (P=.635; PSE=177.9±14.5 beats/min, placebo=178.4±18.5 beats/min), or in anxiety-state levels (P=.650; PSE=38.4±11.6, placebo=38.1±8.8). A 2.5-mg/kg dose of PSE had no effect on 800-m performance for female NCAA runners. More research is needed to determine if PSE should be a specified banned substance.

Persistent northward North Atlantic tropical cyclone track migration over the past five centuries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baldini, Lisa M.; Baldini, James U. L.; McElwaine, Jim N.

Accurately predicting future tropical cyclone risk requires understanding the fundamental controls on tropical cyclone dynamics. Here we present an annually-resolved 450-year reconstruction of western Caribbean tropical cyclone activity developed using a new coupled carbon and oxygen isotope ratio technique in an exceptionally well-dated stalagmite from Belize. Western Caribbean tropical cyclone activity peaked at 1650 A.D., coincident with maximum Little Ice Age cooling, and decreased gradually until the end of the record in 1983. Considered with other reconstructions, the new record suggests that the mean track of Cape Verde tropical cyclones shifted gradually north-eastward from the western Caribbean toward the Northmore » American east coast over the last 450 years. Since ~1870 A.D., these shifts were largely driven by anthropogenic greenhouse gas and sulphate aerosol emissions. In conclusion, our results strongly suggest that future emission scenarios will result in more frequent tropical cyclone impacts on the financial and population centres of the northeastern United States.« less

Persistent northward North Atlantic tropical cyclone track migration over the past five centuries

NASA Astrophysics Data System (ADS)

Baldini, Lisa M.; Baldini, James U. L.; McElwaine, Jim N.; Frappier, Amy Benoit; Asmerom, Yemane; Liu, Kam-Biu; Prufer, Keith M.; Ridley, Harriet E.; Polyak, Victor; Kennett, Douglas J.; MacPherson, Colin G.; Aquino, Valorie V.; Awe, Jaime; Breitenbach, Sebastian F. M.

2016-11-01

Accurately predicting future tropical cyclone risk requires understanding the fundamental controls on tropical cyclone dynamics. Here we present an annually-resolved 450-year reconstruction of western Caribbean tropical cyclone activity developed using a new coupled carbon and oxygen isotope ratio technique in an exceptionally well-dated stalagmite from Belize. Western Caribbean tropical cyclone activity peaked at 1650 A.D., coincident with maximum Little Ice Age cooling, and decreased gradually until the end of the record in 1983. Considered with other reconstructions, the new record suggests that the mean track of Cape Verde tropical cyclones shifted gradually north-eastward from the western Caribbean toward the North American east coast over the last 450 years. Since ~1870 A.D., these shifts were largely driven by anthropogenic greenhouse gas and sulphate aerosol emissions. Our results strongly suggest that future emission scenarios will result in more frequent tropical cyclone impacts on the financial and population centres of the northeastern United States.

Persistent northward North Atlantic tropical cyclone track migration over the past five centuries

DOE PAGES

Baldini, Lisa M.; Baldini, James U. L.; McElwaine, Jim N.; ...

2016-11-23

Accurately predicting future tropical cyclone risk requires understanding the fundamental controls on tropical cyclone dynamics. Here we present an annually-resolved 450-year reconstruction of western Caribbean tropical cyclone activity developed using a new coupled carbon and oxygen isotope ratio technique in an exceptionally well-dated stalagmite from Belize. Western Caribbean tropical cyclone activity peaked at 1650 A.D., coincident with maximum Little Ice Age cooling, and decreased gradually until the end of the record in 1983. Considered with other reconstructions, the new record suggests that the mean track of Cape Verde tropical cyclones shifted gradually north-eastward from the western Caribbean toward the Northmore » American east coast over the last 450 years. Since ~1870 A.D., these shifts were largely driven by anthropogenic greenhouse gas and sulphate aerosol emissions. In conclusion, our results strongly suggest that future emission scenarios will result in more frequent tropical cyclone impacts on the financial and population centres of the northeastern United States.« less

Reconfigurable Full-Page Braille Displays

NASA Technical Reports Server (NTRS)

Garner, H. Douglas

1994-01-01

Electrically actuated braille display cells of proposed type arrayed together to form full-page braille displays. Like other braille display cells, these provide changeable patterns of bumps driven by digitally recorded text stored on magnetic tapes or in solid-state electronic memories. Proposed cells contain electrorheological fluid. Viscosity of such fluid increases in strong electrostatic field.

Ubiquitous Exsolution of Pentlandite and Troilite in Pyrrhotite from the TIL 91722 CM2 Carbonaceous Chondrite: A Record of Low Temperature Solid State Processes

NASA Astrophysics Data System (ADS)

Brearley, A. J.; Martinez, C.

2010-03-01

SEM and TEM studies show that submicron exsolution of pentlandite and troilite occurred at very low temperatures in pyrrhotite in the TIL 91722 CM2 chondrite. The exsolution occurred below 373K on the CM chondrite parent body.

Mixed-Mode Decohesion Finite Elements for the Simulation of Delamination in Composite Materials

NASA Technical Reports Server (NTRS)

Camanho, Pedro P.; Davila, Carlos G.

2002-01-01

A new decohesion element with mixed-mode capability is proposed and demonstrated. The element is used at the interface between solid finite elements to model the initiation and non-self-similar growth of delaminations. A single relative displacement-based damage parameter is applied in a softening law to track the damage state of the interface and to prevent the restoration of the cohesive state during unloading. The softening law for mixed-mode delamination propagation can be applied to any mode interaction criterion such as the two-parameter power law or the three-parameter Benzeggagh-Kenane criterion. To demonstrate the accuracy of the predictions and the irreversibility capability of the constitutive law, steady-state delamination growth is simulated for quasistatic loading-unloading cycles of various single mode and mixed-mode delamination test specimens.

40 CFR 279.65 - Tracking.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 28 2012-07-01 2012-07-01 false Tracking. 279.65 Section 279.65 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) STANDARDS FOR THE MANAGEMENT OF USED OIL Standards for Used Oil Burners Who Burn Off-Specification Used Oil for...

40 CFR 279.65 - Tracking.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 27 2014-07-01 2014-07-01 false Tracking. 279.65 Section 279.65 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) STANDARDS FOR THE MANAGEMENT OF USED OIL Standards for Used Oil Burners Who Burn Off-Specification Used Oil for...

40 CFR 279.65 - Tracking.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 28 2013-07-01 2013-07-01 false Tracking. 279.65 Section 279.65 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) STANDARDS FOR THE MANAGEMENT OF USED OIL Standards for Used Oil Burners Who Burn Off-Specification Used Oil for...

40 CFR 279.65 - Tracking.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 26 2010-07-01 2010-07-01 false Tracking. 279.65 Section 279.65 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) STANDARDS FOR THE MANAGEMENT OF USED OIL Standards for Used Oil Burners Who Burn Off-Specification Used Oil for...

40 CFR 279.65 - Tracking.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 27 2011-07-01 2011-07-01 false Tracking. 279.65 Section 279.65 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) STANDARDS FOR THE MANAGEMENT OF USED OIL Standards for Used Oil Burners Who Burn Off-Specification Used Oil for...

KSC00pp1030

NASA Image and Video Library

2000-07-22

The railroad tracks are under repair at Kennedy Space Center. This section of track is located on KSC property, just north of the NASA Causeway in the KSC Industrial Area. The repairs were required following the minor derailment of two solid rocket booster segment cars on July 18

KSC-00pp1031

NASA Image and Video Library

2000-07-27

Railroad track repairs have been completed at Kennedy Space Center. This section of track is located on KSC property, just north of the NASA Causeway in the KSC Industrial Area. The repairs were required following the minor derailment of two solid rocket booster segment cars on July 18

KSC-00pp1029

NASA Image and Video Library

2000-07-22

The railroad tracks are under repair at Kennedy Space Center. This section of track is located on KSC property, just north of the NASA Causeway in the KSC Industrial Area. The repairs were required following the minor derailment of two solid rocket booster segment cars on July 18

KSC-00pp1032

NASA Image and Video Library

2000-07-27

Railroad track repairs have been completed at Kennedy Space Center. This section of track is located on KSC property, just north of the NASA Causeway in the KSC Industrial Area. The repairs were required following the minor derailment of two solid rocket booster segment cars on July 18

KSC-00pp1030

NASA Image and Video Library

2000-07-22

The railroad tracks are under repair at Kennedy Space Center. This section of track is located on KSC property, just north of the NASA Causeway in the KSC Industrial Area. The repairs were required following the minor derailment of two solid rocket booster segment cars on July 18

KSC00pp1031

NASA Image and Video Library

2000-07-27

Railroad track repairs have been completed at Kennedy Space Center. This section of track is located on KSC property, just north of the NASA Causeway in the KSC Industrial Area. The repairs were required following the minor derailment of two solid rocket booster segment cars on July 18

KSC00pp1032

NASA Image and Video Library

2000-07-27

Railroad track repairs have been completed at Kennedy Space Center. This section of track is located on KSC property, just north of the NASA Causeway in the KSC Industrial Area. The repairs were required following the minor derailment of two solid rocket booster segment cars on July 18

KSC00pp1029

NASA Image and Video Library

2000-07-22

The railroad tracks are under repair at Kennedy Space Center. This section of track is located on KSC property, just north of the NASA Causeway in the KSC Industrial Area. The repairs were required following the minor derailment of two solid rocket booster segment cars on July 18

Robust decoding of selective auditory attention from MEG in a competing-speaker environment via state-space modeling✩

PubMed Central

Akram, Sahar; Presacco, Alessandro; Simon, Jonathan Z.; Shamma, Shihab A.; Babadi, Behtash

2015-01-01

The underlying mechanism of how the human brain solves the cocktail party problem is largely unknown. Recent neuroimaging studies, however, suggest salient temporal correlations between the auditory neural response and the attended auditory object. Using magnetoencephalography (MEG) recordings of the neural responses of human subjects, we propose a decoding approach for tracking the attentional state while subjects are selectively listening to one of the two speech streams embedded in a competing-speaker environment. We develop a biophysically-inspired state-space model to account for the modulation of the neural response with respect to the attentional state of the listener. The constructed decoder is based on a maximum a posteriori (MAP) estimate of the state parameters via the Expectation Maximization (EM) algorithm. Using only the envelope of the two speech streams as covariates, the proposed decoder enables us to track the attentional state of the listener with a temporal resolution of the order of seconds, together with statistical confidence intervals. We evaluate the performance of the proposed model using numerical simulations and experimentally measured evoked MEG responses from the human brain. Our analysis reveals considerable performance gains provided by the state-space model in terms of temporal resolution, computational complexity and decoding accuracy. PMID:26436490

75 FR 34754 - Privacy Act; Notification of a New Privacy Act System of Records, Title Eight Automated Paperless...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-18

... automated case management system, to process complaints, compliance reviews, and to track the activities... comment on the new system of records. The new system report was submitted to the Office of Management and... a New Privacy Act System of Records, Title Eight Automated Paperless Office Tracking System (TEAPOTS...

Readout characteristics of a minute aperture-mounted optical head slider flying above a submicron wide metal patterned medium track

NASA Astrophysics Data System (ADS)

Ohkubo, Toshifumi; Hirota, Terunao; Oumi, Manabu; Hirata, Masakazu; Nakajima, Kunio

2004-10-01

Advances in a digital network society require both higher densities and higher transfer rates in all sorts of storage devices. In optical recording, the trend toward higher recording density and larger storage capacity requires novel surface recording technologies that would drastically improve recording density. To satisfy these severe requirements, we have already proposed a compact integrated optical head slider assembly for proximity optical recording based on the "near field principle". Using the optical head slider, we have successfully demonstrated readout signals from 200 to 150-nm-long bit patterns at frequency bands up to approximately 10 MHz. However, from the practical point of view, it is quite necessary to evaluate readout signals from patterns of smaller (sub-micron to sub-sub-micron) track width in order to prove high-density recording potential. In this paper, we have investigated tracking accuracy characteristics utilizing sub-micron sized alternate patterns of 1-mm length formed in a straight line in the circumferential direction of the medium. Arranging precisely the head's relative position to these recorded patterns, we have successfully obtained readout signals just crossing the sub-micron line-and-space pattern's boundaries. Assuming that an aperture runs along an accurate trajectory of the arc of a circle, readout signal amplitude variations when crossing the pattern edge at a right angle have precisely predicted. Also, the influences of track width on maximum readout signal intensity and tracking sensitivity are discussed in detail.

Challenge of Near-Field Recording beyond 50.4 Gbit/in2

NASA Astrophysics Data System (ADS)

Kishima, Koichiro; Ichimura, Isao; Saito, Kimihiro; Yamamoto, Kenji; Kuroda, Yuji; Iida, Atsushi; Masuhara, Shin; Osato, Kiyoshi

2002-03-01

The possibility of an areal density over 50 Gbit/in2 was examined in near-field phase-change recording. The disk structure was optimized to maximize readout signals under the land-and-groove recording condition at a tracking pitch of 160 nm. We also evaluated the signal crosstalk from adjacent tracks. Eye diagrams of 50.4 Gbit/in2 areal density were demonstrated using 1.5 \\mathit{NA} optics and a GaN laser diode. The track pitch and linear bit density are 160 nm and 80 nm/bit, respectively. The transmission electron microscope (TEM) micrograph of recorded amorphous marks at an areal density of 50.4 Gbit/in2 is also presented.

Short-period variability in terrestrial water storage from GNSS observations of Earth surface deformation

NASA Astrophysics Data System (ADS)

Borsa, A. A.; Adusumilli, S.; Agnew, D. C.; Silverii, F.; Small, E. E.

2017-12-01

Modern geodetic observations of Earth surface deformation, initially targeted at processes such as tectonics and volcanism, also record the subtle signature of mass movements within Earth's atmosphere and hydrosphere. These observations, which track the elastic response of the solid earth to changing surface mass loads, are clearly evident in position time series from permanent Global Navigation Satellite System (GNSS) stations, which recent work has used to recover changes in terrestrial water storage (TWS) over seasonal and multi-annual time scales. Earth's elastic reponse is nearly instantaneous, which suggests the possibility of observing TWS changes at much shorter periods, limited only by the 24 hour resolution of standard GNSS data products and noise in the GNSS position estimates. We present results showing that TWS increases from individual storms can be recovered using the GNSS network in the United States, and that the water mass changes are similar to gridded precipitation estimates from the National Centers for Environmental Prediction (NCEP). The gradual decline we observe in TWS following each storm is diagnostic of runoff and local evapotranspiration, and varies by location. By greatly increasing the temporal resolution of GNSS-derived estimates of TWS, we hope to provide constraints on integrated water fluxes from hydrological models on all relevant timescales.

Pressure–temperature evolution of primordial solar system solids during impact-induced compaction

PubMed Central

Bland, P. A.; Collins, G. S.; Davison, T. M.; Abreu, N. M.; Ciesla, F. J.; Muxworthy, A. R.; Moore, J.

2014-01-01

Prior to becoming chondritic meteorites, primordial solids were a poorly consolidated mix of mm-scale igneous inclusions (chondrules) and high-porosity sub-μm dust (matrix). We used high-resolution numerical simulations to track the effect of impact-induced compaction on these materials. Here we show that impact velocities as low as 1.5 km s−1 were capable of heating the matrix to >1,000 K, with pressure–temperature varying by >10 GPa and >1,000 K over ~100 μm. Chondrules were unaffected, acting as heat-sinks: matrix temperature excursions were brief. As impact-induced compaction was a primary and ubiquitous process, our new understanding of its effects requires that key aspects of the chondrite record be re-evaluated: palaeomagnetism, petrography and variability in shock level across meteorite groups. Our data suggest a lithification mechanism for meteorites, and provide a ‘speed limit’ constraint on major compressive impacts that is inconsistent with recent models of solar system orbital architecture that require an early, rapid phase of main-belt collisional evolution. PMID:25465283

Mass transport waves amplified by intense Greenland melt and detected in solid Earth deformation

NASA Astrophysics Data System (ADS)

Adhikari, S.; Ivins, E. R.; Larour, E.

2017-05-01

The annual cycle and secular trend of Greenland mass loading are well recorded in measurements of solid Earth deformation. Horizontal crustal displacements can potentially track the spatiotemporal detail of mass changes with great fidelity. Our analysis of Greenland crustal motion data reveals that a significant excitation of horizontal amplitudes occurs during the intense melt years. We discover that solitary seasonal waves of substantial mass transport (1.67 ± 0.54 Gt/month) traveled at an average speed of 7.1 km/month through Rink Glacier in 2012. We deduce that intense surface melting enhanced either basal lubrication or softening of shear margins, or both, causing the glacier to thin dynamically in summer. The newly routed upstream subglacial water was likely to be both retarded and inefficient, thus providing a causal mechanism for the prolonged ice transport to continue well into the winter months. As the climate continues to produce increasingly warmer spring and summer, amplified seasonal waves of mass transport may become ever more present with important ramifications for the future sea level rise.

[Deep brain recording and length of surgery in stereotactic and functional neurosurgery for movement disorders].

PubMed

Teijeiro, Juan; Macías, Raúl J; Maragoto, Carlos; García, Iván; Alvarez, Mario; Quintanal, Nelson E

2014-01-01

Our objectives were to study the length of multi-unit recordings (MURs) of brain activity in 20 years of movement disorder neurosurgeries and to determine the number of times in which it was necessary for the teams using single-unit recording (SUR) to explore all the electrode tracks in the simultaneously recorded sites (SRS). This was a retrospective descriptive statistical analysis of MUR length on 4,296 tracks in 952 surgeries. The exclusion criteria were: tracks with fewer than 5 recorded signals, tracks that had a signal length different from the habitual 2s, or there being unusual situations not related to the MUR, as well as the first 20 surgeries of each surgical target. This yielded a total of 3,448 tracks in 805 surgeries. We also determined the number of the total 952 surgeries in which all the tracks in the SURs of the SRS were explored. The mean and its confidence interval (P=.05) of time per MUR track were 5.49±0.16min in subthalamic nucleus surgery, 8.82±0.24min in the medial or internal globus pallidus) and 18.51±1.31min in the ventral intermediate nucleus of the thalamus. For the total sum of tracks per surgery, in 75% of cases the total time was less than 39min in subthalamic nucleus, almost 42min in the medial or internal globus pallidus and less than 1h and 17min in ventral intermediate nucleus of the thalamus. All the tracks in the SUR SRS were explored in only 4.2% of the surgeries. The impact of MUR on surgical time is acceptable for this guide in objective localization for surgical targets, without having to use several simultaneous electrodes (not all indispensable in most of the cases). Consequently, there is less risk for the patient. Copyright © 2013 Sociedad Española de Neurocirugía. Published by Elsevier España. All rights reserved.

FLUSH - PREDICTION OF FLOW PARAMETERS OF SLUSH HYDROGEN

NASA Technical Reports Server (NTRS)

Hardy, T.

1994-01-01

Slush hydrogen, a mixture of the solid and liquid phases of hydrogen, is a possible source of fuel for the National Aerospace Plane (NASP) Project. Advantages of slush hydrogen over liquid hydrogen include greater heat capacity and greater density. However, practical use of slush hydrogen as a fuel requires systems of lines, valves, etc. which are designed to deliver the fuel in slush form with minimal solid loss as a result of pipe heating or flow friction. Engineers involved with the NASP Project developed FLUSH to calculate the pressure drop and slush hydrogen solid fraction loss for steady-state, one-dimensional flow. FLUSH solves the steady-state, one-dimensional energy equation and the Bernoulli equation for pipe flow. The program performs these calculations for each two-node element--straight pipe length, elbow, valve, fitting, or other part of the piping system--specified by the user. The user provides flow rate, upstream pressure, initial solid hydrogen fraction, element heat leak, and element parameters such as length and diameter. For each element, FLUSH first calculates the pressure drop, then figures the slush solid fraction exiting the element. The code employs GASPLUS routines to calculate thermodynamic properties for the slush hydrogen. FLUSH is written in FORTRAN IV for DEC VAX series computers running VMS. An executable is provided on the tape. The GASPLUS physical properties routines which are required for building the executable are included as one object library on the program media (full source code for GASPLUS is available separately as COSMIC Program Number LEW-15091). FLUSH is available in DEC VAX BACKUP format on a 9-track 1600 BPI magnetic tape (standard media) or on a TK50 tape cartridge. FLUSH was developed in 1989.

A 10-year experience of tuberculosis in solid-organ transplant recipients.

PubMed

Ulubay, Gaye; Kupeli, Elif; Duvenci Birben, Ozlem; Seyfettin, Emine Pinar; Dogrul, Mustafa Ilgaz; Ozsancak Ugurlu, Aylin; Oner Eyuboglu, Fusun; Haberal, Mehmet

2015-04-01

Tuberculosis remains an important problem in solid-organ transplant patients due to their immunocompromised state. The objective of the present study was to report the incidence, demographic characteristics, and various presentations of tuberculosis in solid-organ transplant recipients. We evaluated a total of 999 patients (male/female = 665/334, 661 renal and 338 liver transplants) who underwent solid-organ transplant between 2003 and 2013. The medical records of all patients were retrospectively reviewed. Patients' demographics, transplant type, primary site of tuberculosis specimen culture and pathology results, chest radiograph, and thoracic computed tomography findings, total blood count and chemistry were all recorded. Among the 999 subjects, 19 patients (1.9%) (male/female: 15/4, mean ± SD age, 42 ± 18.5 y) were diagnosed with tuberculosis. The majority of patients (85%) were diagnosed with tuberculosis within 6 months after transplant, and 15% were diagnosed within 3 months. Most diagnoses of tuberculosis were based on histopathologic examination of biopsy material. Of these patients, 9 were diagnosed with pulmonary tuberculosis, 8 had extrapulmonary tuberculosis, and 2 had both. Nontuberculosis mycobacteria infections were detected in 3 patients. Even with a negative exposure history, tuberculosis can manifest as different clinic presentations in solid-organ transplant patients on immunosuppressive drugs, particularly in the first 6 months after transplant. Therefore, clinicians should always consider tuberculosis as the potential cause of an infectious disease with unknown cause to successfully diagnose and manage solid-organ transplant recipients.

Coherent manipulation of a solid-state artificial atom with few photons.

PubMed

Giesz, V; Somaschi, N; Hornecker, G; Grange, T; Reznychenko, B; De Santis, L; Demory, J; Gomez, C; Sagnes, I; Lemaître, A; Krebs, O; Lanzillotti-Kimura, N D; Lanco, L; Auffeves, A; Senellart, P

2016-06-17

In a quantum network based on atoms and photons, a single atom should control the photon state and, reciprocally, a single photon should allow the coherent manipulation of the atom. Both operations require controlling the atom environment and developing efficient atom-photon interfaces, for instance by coupling the natural or artificial atom to cavities. So far, much attention has been drown on manipulating the light field with atomic transitions, recently at the few-photon limit. Here we report on the reciprocal operation and demonstrate the coherent manipulation of an artificial atom by few photons. We study a quantum dot-cavity system with a record cooperativity of 13. Incident photons interact with the atom with probability 0.95, which radiates back in the cavity mode with probability 0.96. Inversion of the atomic transition is achieved for 3.8 photons on average, showing that our artificial atom performs as if fully isolated from the solid-state environment.

Structural characterization of Er(3+),Yb(3+)-doped Gd2O3 phosphor, synthesized using the solid-state reaction method, and its luminescence behavior.

PubMed

Tamrakar, Raunak Kumar; Bisen, D P; Brahme, Nameeta

2016-02-01

We report the synthesis and structural characterization of Er(3+),Yb(3+)-doped Gd2O3 phosphor. The sample was prepared using the conventional solid-state reaction method, which is the most suitable method for large-scale production. The prepared phosphor sample was characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FTIR), thermoluminescence (TL), photoluminescence (PL) and CIE techniques. For PL studies, the excitation and emission spectra of Gd2O3 phosphor doped with Er(3+) and Yb(3+) were recorded. The excitation spectrum was recorded at a wavelength of 551 nm and showed an intense peak at 276 nm. The emission spectrum was recorded at 276 nm excitation and showed peaks in all blue, green and red regions, which indicate that the prepared phosphor may act as a single host for white light-emitting diode (WLED) applications, as verified by International de I'Eclairage (CIE) techniques. From the XRD data, the calculated average crystallite size of Er(3+) and Yb(3+) -doped Gd2O3 phosphor is ~ 38 nm. A TL study was carried out for the phosphor using UV irradiation. The TL glow curve was recorded for UV, beta and gamma irradiations, and the kinetic parameters were also calculated. In addition, the trap parameters of the prepared phosphor were also studied using computerized glow curve deconvolution (CGCD). Copyright © 2015 John Wiley & Sons, Ltd.

Using State Early Care and Education Workforce Registry Data to Inform Training-Related Questions: Issues to Consider. Research Report. ETS RR-16-31

ERIC Educational Resources Information Center

Ackerman, Debra J.

2016-01-01

The current early care and education (ECE) policy context is bringing increased attention to the training completed by the child care workforce and to the use of registries to track such training. Although ECE workforce registries are designed to record individuals' data, aggregate registry data have the potential to shed light on the workforce's…

A description and comparison of selected forest carbon registries: a guide for States considering the development of a forest carbon registry

Treesearch

Jessica Call; Jennifer Hayes

2007-01-01

There is increasing interest in tools for measuring and reducing emissions of carbon dioxide, a major greenhouse gas. Two tools that have been receiving a lot of attention include carbon markets and carbon registries. Carbon registries are established to record and track net carbon emission levels over time. These registries provide quantifiable and verifiable carbon...

Groundwater Depletion and the Sharp Increase of Seismicity in the Southern States, How GRACE Data Could Help?

NASA Astrophysics Data System (ADS)

Hong, Z.; Hasan, E.; Hong, Y.; Xia, B.; Zhong, H.

2016-12-01

This study is a contribution to how NASA's Gravity Recovery and Climate Experiment (GRACE) data may be used to track anthropogenic related change in the groundwater in the Southern Great Plains (SGP) as well recently increased seismicity in the southern states. The SGP contains one of the most important groundwater aquifers in the United States, the Ogallala groundwater aquifer, which has been exploited since 1900. Meanwhile, the recent activities of oil and gas extraction from the unconventional shall reservoir systems has led to significantly increased groundwater withdrawal and injection of wastewater. Consequently, numerous induced fracture related earthquakes have been recorded in Oklahoma and Texas between 2002 and 2016 The current paper investigates the utility of GRACE data along with the Land Water Content (LWC) information from the Global Land Data Assimilation System (GLDAS) to monitor and track the groundwater changes in three southern states of SGP (Oklahoma, Texas and New Mexico). Additionally, the paper investigates links between active seismicity and the injection of the wastewater due to the oil and gas production. Using GRACE data yields unprecedented information about the inter-annual changes in the Total Water Storage (TWS) from 2002 to 2016 over SGP. The LWC data set sums the soil moisture records with the the total canopy water storage to reveal the total land surface water content. The arithmetic difference between the TWS and LWC is the Groundwater Anomaly (GWA) for any particular region. In the current study, the GWA analysis reveals the following: (1) statistically significant drop of the GWA of about - 27 mm from 2002 to 2007 due to natural and anthropogenic causes; (2) the increased precipitation records from 2008 to 2011 over SGP leads to significant recovery in TWS and an increase in the groundwater content of about 40 mm; (3) the period from 2012 to 2015 experienced increased GWA of about - 6 mm for the period. Using the available seismicity records showed high agreement between the seismicity and the oil production locations. Additionally, the correlation between the groundwater changes and the seismic activity in the study region showed that the changes in groundwater levels are associated with regions of induced seismic activities.

Evidence-based use of electronic clinical tracking systems in advanced practice registered nurse education: an integrative review.

PubMed

Branstetter, M Laurie; Smith, Lynette S; Brooks, Andrea F

2014-07-01

Over the past decade, the federal government has mandated healthcare providers to incorporate electronic health records into practice by 2015. This technological update in healthcare documentation has generated a need for advanced practice RN programs to incorporate information technology into education. The National Organization of Nurse Practitioner Faculties created core competencies to guide program standards for advanced practice RN education. One core competency is Technology and Information Literacy. Educational programs are moving toward the utilization of electronic clinical tracking systems to capture students' clinical encounter data. The purpose of this integrative review was to evaluate current research on advanced practice RN students' documentation of clinical encounters utilizing electronic clinical tracking systems to meet advanced practice RN curriculum outcome goals in information technology as defined by the National Organization of Nurse Practitioner Faculties. The state of the science depicts student' and faculty attitudes, preferences, opinions, and data collections of students' clinical encounters. Although electronic clinical tracking systems were utilized to track students' clinical encounters, these systems have not been evaluated for meeting information technology core competency standards. Educational programs are utilizing electronic clinical tracking systems with limited evidence-based literature evaluating the ability of these systems to meet the core competencies in advanced practice RN programs.

Single-Molecule Tracking and Its Application in Biomolecular Binding Detection.

PubMed

Liu, Cong; Liu, Yen-Liang; Perillo, Evan P; Dunn, Andrew K; Yeh, Hsin-Chih

2016-01-01

In the past two decades significant advances have been made in single-molecule detection, which enables the direct observation of single biomolecules at work in real time and under physiological conditions. In particular, the development of single-molecule tracking (SMT) microscopy allows us to monitor the motion paths of individual biomolecules in living systems, unveiling the localization dynamics and transport modalities of the biomolecules that support the development of life. Beyond the capabilities of traditional camera-based tracking techniques, state-of-the-art SMT microscopies developed in recent years can record fluorescence lifetime while tracking a single molecule in the 3D space. This multiparameter detection capability can open the door to a wide range of investigations at the cellular or tissue level, including identification of molecular interaction hotspots and characterization of association/dissociation kinetics between molecules. In this review, we discuss various SMT techniques developed to date, with an emphasis on our recent development of the next generation 3D tracking system that not only achieves ultrahigh spatiotemporal resolution but also provides sufficient working depth suitable for live animal imaging. We also discuss the challenges that current SMT techniques are facing and the potential strategies to tackle those challenges.

Single-Molecule Tracking and Its Application in Biomolecular Binding Detection

PubMed Central

Liu, Cong; Liu, Yen-Liang; Perillo, Evan P.; Dunn, Andrew K.; Yeh, Hsin-Chih

2016-01-01

In the past two decades significant advances have been made in single-molecule detection, which enables the direct observation of single biomolecules at work in real time and under physiological conditions. In particular, the development of single-molecule tracking (SMT) microscopy allows us to monitor the motion paths of individual biomolecules in living systems, unveiling the localization dynamics and transport modalities of the biomolecules that support the development of life. Beyond the capabilities of traditional camera-based tracking techniques, state-of-the-art SMT microscopies developed in recent years can record fluorescence lifetime while tracking a single molecule in the 3D space. This multiparameter detection capability can open the door to a wide range of investigations at the cellular or tissue level, including identification of molecular interaction hotspots and characterization of association/dissociation kinetics between molecules. In this review, we discuss various SMT techniques developed to date, with an emphasis on our recent development of the next generation 3D tracking system that not only achieves ultrahigh spatiotemporal resolution but also provides sufficient working depth suitable for live animal imaging. We also discuss the challenges that current SMT techniques are facing and the potential strategies to tackle those challenges. PMID:27660404

Diverse dinosaur-dominated ichnofaunas from the Potomac Group (Lower Cretaceous) Maryland

USGS Publications Warehouse

Stanford, Ray; Lockley, Martin G.; Weems, Robert E.

2007-01-01

Until recently fossil footprints were virtually unknown from the Cretaceous of the eastern United States. The discovery of about 300 footprints in iron-rich siliciclastic facies of the Patuxent Formation (Potomac Group) of Aptian age is undoubtedly one of the most significant Early Cretaceous track discoveries since the Paluxy track discoveries in Texas in the 1930s. The Patuxent tracks include theropod, sauropod, ankylosaur and ornithopod dinosaur footprints, pterosaur tracks, and miscellaneous mammal and other vertebrate ichnites that collectively suggest a diversity of about 14 morphotypes. This is about twice the previous maximum estimate for any known Early Cretaceous vertebrate ichnofauna. Among the more distinctive forms are excellent examples of hypsilophodontid tracks and a surprisingly large mammal footprint. A remarkable feature of the Patuxent track assemblage is the high proportion of small tracks indicative of hatchlings, independently verified by the discovery of a hatchling-sized dinosaur. Such evidence suggests the proximity of nest sites. The preservation of such small tracks is very rare in the Cretaceous track record, and indeed throughout most of the Mesozoic.This unusual preservation not only provides us with a window into a diverse Early Cretaceous ecosystem, but it also suggests the potential of such facies to provide ichnological bonanzas. A remarkable feature of the assemblage is that it consists largely of reworked nodules and clasts that may have previously been reworked within the Patuxent Formation. Such unusual contexts of preservation should provide intriguing research opportunities for sedimentologists interested in the diagenesis and taphonomy of a unique track-bearing facies.

Novel Image Processing Interface to Relate DSB Spatial Distribution from Immunofluorescence Foci Experiments to the State-of-the-Art Models of DNA Breakage

NASA Technical Reports Server (NTRS)

Ponomarev, A. L.; Cucinotta, F. A.

2004-01-01

A recently developed software (NASARadiationTrackImage) allows a quick and automatic segmentation of foci that indicate spatial localization of specific proteins that are visualized by immunofluorescence. Of interest are the spatial and temporal distribution of foci such as gammaH2AX, a signal of the phosphorylation of a variant of the histone H2A that has been shown to correspond to DSBs, or proteins involved in DSB processing, such as ATM, Rad51, and p53, following exposures of human cells to high charge and energy (HZE) ion irradiation. Experimental data are recorded as sets of two-dimensional images in color with cells and foci of gammaH2AX, ATM, Rad51 or others shown. Different cells, levels of radiation and timing after radiation were recorded. The software allows us to calculate the number of foci per cell, overall intensity of light in foci and their spatial organization. A simple statistical model allows for testing of foci overlap (eclipse). A more complex statistical model previously known as DNAbreak simulates track structure and random chromosome geometry. It has one adjustable parameter corresponding to an average intensity of DSB creation in cubic micrometers of DNA volume per particle track or unit dose. Its limitation is the low-resolution limit both in physical space and DSB's along DNA. It works adequately on the scale of a cell and provides further insights on how the geometry of tracks and DNA affects genomic damage of the cell and subsequent repair. Future developments of the model for the description of the time evolution of DNA damage response proteins, and more robust track structure models will be discussed.

Passive acoustic tracking of singing humpback whales (Megaptera novaeangliae) on a northwest Atlantic feeding ground.

PubMed

Stanistreet, Joy E; Risch, Denise; Van Parijs, Sofie M

2013-01-01

Passive acoustic tracking provides an unobtrusive method of studying the movement of sound-producing animals in the marine environment where traditional tracking methods may be costly or infeasible. We used passive acoustic tracking to characterize the fine-scale movements of singing humpback whales (Megaptera novaeangliae) on a northwest Atlantic feeding ground. Male humpback whales produce complex songs, a phenomenon that is well documented in tropical regions during the winter breeding season, but also occurs at higher latitudes during other times of year. Acoustic recordings were made throughout 2009 using an array of autonomous recording units deployed in the Stellwagen Bank National Marine Sanctuary. Song was recorded during spring and fall, and individual singing whales were localized and tracked throughout the array using a correlation sum estimation method on the time-synchronized recordings. Tracks were constructed for forty-three song sessions, revealing a high level of variation in movement patterns in both the spring and fall seasons, ranging from slow meandering to faster directional movement. Tracks were 30 min to 8 h in duration, and singers traveled distances ranging from 0.9 to 20.1 km. Mean swimming speed was 2.06 km/h (SD 0.95). Patterns and rates of movement indicated that most singers were actively swimming. In one case, two singers were tracked simultaneously, revealing a potential acoustic interaction. Our results provide a first description of the movements of singers on a northwest Atlantic feeding ground, and demonstrate the utility of passive acoustic tracking for studying the fine-scale movements of cetaceans within the behavioral context of their calls. These methods have further applications for conservation and management purposes, particularly by enhancing our ability to estimate cetacean densities using passive acoustic monitoring.

Passive Acoustic Tracking of Singing Humpback Whales (Megaptera novaeangliae) on a Northwest Atlantic Feeding Ground

PubMed Central

Stanistreet, Joy E.; Risch, Denise; Van Parijs, Sofie M.

2013-01-01

Passive acoustic tracking provides an unobtrusive method of studying the movement of sound-producing animals in the marine environment where traditional tracking methods may be costly or infeasible. We used passive acoustic tracking to characterize the fine-scale movements of singing humpback whales (Megaptera novaeangliae) on a northwest Atlantic feeding ground. Male humpback whales produce complex songs, a phenomenon that is well documented in tropical regions during the winter breeding season, but also occurs at higher latitudes during other times of year. Acoustic recordings were made throughout 2009 using an array of autonomous recording units deployed in the Stellwagen Bank National Marine Sanctuary. Song was recorded during spring and fall, and individual singing whales were localized and tracked throughout the array using a correlation sum estimation method on the time-synchronized recordings. Tracks were constructed for forty-three song sessions, revealing a high level of variation in movement patterns in both the spring and fall seasons, ranging from slow meandering to faster directional movement. Tracks were 30 min to 8 h in duration, and singers traveled distances ranging from 0.9 to 20.1 km. Mean swimming speed was 2.06 km/h (SD 0.95). Patterns and rates of movement indicated that most singers were actively swimming. In one case, two singers were tracked simultaneously, revealing a potential acoustic interaction. Our results provide a first description of the movements of singers on a northwest Atlantic feeding ground, and demonstrate the utility of passive acoustic tracking for studying the fine-scale movements of cetaceans within the behavioral context of their calls. These methods have further applications for conservation and management purposes, particularly by enhancing our ability to estimate cetacean densities using passive acoustic monitoring. PMID:23593447

Packaging of a large capacity magnetic bubble domain spacecraft recorder

NASA Technical Reports Server (NTRS)

Becker, F. J.; Stermer, R. L.

1977-01-01

A Solid State Spacecraft Data Recorder (SSDR), based on bubble domain technology, having a storage capacity of 10 to the 8th power bits, was designed and is being tested. The recorder consists of two memory modules each having 32 cells, each cell containing sixteen 100 kilobit serial bubble memory chips. The memory modules are interconnected to a Drive and Control Unit (DCU) module containing four microprocessors, 500 integrated circuits, a RAM core memory and two PROM's. The two memory modules and DCU are housed in individual machined aluminum frames, are stacked in brick fashion and through bolted to a base plate assembly which also houses the power supply.

Marine mammal tracks from two-hydrophone acoustic recordings made with a glider

NASA Astrophysics Data System (ADS)

Küsel, Elizabeth T.; Munoz, Tessa; Siderius, Martin; Mellinger, David K.; Heimlich, Sara

2017-04-01

A multinational oceanographic and acoustic sea experiment was carried out in the summer of 2014 off the western coast of the island of Sardinia, Mediterranean Sea. During this experiment, an underwater glider fitted with two hydrophones was evaluated as a potential tool for marine mammal population density estimation studies. An acoustic recording system was also tested, comprising an inexpensive, off-the-shelf digital recorder installed inside the glider. Detection and classification of sounds produced by whales and dolphins, and sometimes tracking and localization, are inherent components of population density estimation from passive acoustics recordings. In this work we discuss the equipment used as well as analysis of the data obtained, including detection and estimation of bearing angles. A human analyst identified the presence of sperm whale (Physeter macrocephalus) regular clicks as well as dolphin clicks and whistles. Cross-correlating clicks recorded on both data channels allowed for the estimation of the direction (bearing) of clicks, and realization of animal tracks. Insights from this bearing tracking analysis can aid in population density estimation studies by providing further information (bearings), which can improve estimates.

Metastable States Arising from the Ablation of Solid Copper

NASA Astrophysics Data System (ADS)

Andrejeva, Anna; Harris, Joe; Wright, Tim

2014-06-01

Laser ablation is a popular method for generating metal atoms so that metal clusters, complexes, and molecules may be investigated in gas phase spectroscopic studies. However, the initial production of a highly energetic metal plasma from the surface of a solid metal target can produce atoms which are not in their ground electronic state, and consequently atomic spectra can become quite complicated due to transitions arising from metastable atomic excited states which remain populated on the experimental timescale. Presented herein are details of the laser vaporisation source in use by our group. Spectra of atomic copper are presented, recorded via (1+1') and (2+1) resonance enhanced multiphoton ionisation (REMPI) spectroscopy. The energetic regions examined are expected to correspond to the (4s24p) 2P ← 2S and the (4s2nd) 2D ← 2S Rydberg series respectively, but the observed spectra also exhibit many additional contributions which are found to arise from electronically excited states, and these will be discussed.

Solvent effect on the vibrational spectra of Carvedilol.

PubMed

Billes, Ferenc; Pataki, Hajnalka; Unsalan, Ozan; Mikosch, Hans; Vajna, Balázs; Marosi, György

2012-09-01

Carvedilol (CRV) is an important medicament for heart arrhythmia. The aim of this work was the interpretation of its vibrational spectra with consideration on the solvent effect. Infrared and Raman spectra were recorded in solid state as well in solution. The experimental spectra were evaluated using DFT quantum chemical calculations computing the optimized structure, atomic net charges, vibrational frequencies and force constants. The same calculations were done for the molecule in DMSO and aqueous solutions applying the PCM method. The calculated force constants were scaled to the experimentally observed solid state frequencies. The characters of the vibrational modes were determined by their potential energy distributions. Solvent effects on the molecular properties were interpreted. Based on these results vibrational spectra were simulated. Copyright © 2012 Elsevier B.V. All rights reserved.

Track recording plastic compositions

NASA Technical Reports Server (NTRS)

Tarle, Gregory (Inventor)

1983-01-01

Improved nuclear track recording plastic compositions are provided which exhibit greatly decreased surface roughness when etched to produce visible tracks of energetic nuclear particles which have passed into and/or through said plastic. The improved compositions incorporate a small quantity of a phthalic acid ester into the major plastic component which is derived from the polymerization of monomeric di-ethylene glycol bis allyl carbonate. Di-substituted phthalic acid esters are preferred as the added component, with the further perference that the ester substituent has a chain length of 2 or more carbon atoms. The inclusion of the phthalic acid ester to an extent of from about 1-2% by weight of the plastic compositions is sufficient to drastically reduce the surface roughness ordinarily produced when the track recording plastic is contacted by etchants.

Interfacial interaction track of amorphous solid dispersions established by water-soluble polymer and indometacin.

PubMed

Li, Jing; Fan, Na; Wang, Xin; Li, Chang; Sun, Mengchi; Wang, Jian; Fu, Qiang; He, Zhonggui

2017-08-30

The present work studied interfacial interactions of amorphous solid dispersions matrix of indometacin (IMC) that established using PVP K30 (PVP) and PEG 6000 (PEG) by focusing on their interaction forces and wetting process. Infrared spectroscopy (IR), raman spectroscopy, X-ray photoelectron spectra and contact angle instrument were used throughout the study. Hydrogen bond energy formed between PEG and IMC were stronger than that of PVP and IMC evidenced by molecular modeling measurement. The blue shift of raman spectroscopy confirmed that hydrogen bonding forces were formed between IMC and two polymers. The contact angle study can be used as an easy method to determine the dissolution mechanism of amorphous solid dispersions through fitting the profile of contact angle of water on a series of tablets. It is believed that the track of interfacial interactions will certainly become powerful tools to for designing and evaluating amorphous solid dispersions. Copyright © 2017 Elsevier B.V. All rights reserved.

KENNEDY SPACE CENTER, FLA. - Workers ride the rails along with a container enclosing a segment of a solid rocket booster being moved to the main track. Several segments are being returned to Utah for testing. The segments were part of the STS-114 stack. It is the first time actual flight segments that had been stacked for flight in the VAB are being returned for testing. They will undergo firing, which will enable inspectors to check the viability of the solid and verify the life expectancy for stacked segments.

NASA Image and Video Library

2004-01-30

KENNEDY SPACE CENTER, FLA. - Workers ride the rails along with a container enclosing a segment of a solid rocket booster being moved to the main track. Several segments are being returned to Utah for testing. The segments were part of the STS-114 stack. It is the first time actual flight segments that had been stacked for flight in the VAB are being returned for testing. They will undergo firing, which will enable inspectors to check the viability of the solid and verify the life expectancy for stacked segments.

KENNEDY SPACE CENTER, FLA. - The red NASA engine backs up with its cargo of containers in order to change tracks. The containers enclose segments of a solid rocket booster being returned to Utah for testing. The segments were part of the STS-114 stack. It is the first time actual flight segments that had been stacked for flight in the VAB are being returned for testing. They will undergo firing, which will enable inspectors to check the viability of the solid and verify the life expectancy for stacked segments.

NASA Image and Video Library

2004-01-30

KENNEDY SPACE CENTER, FLA. - The red NASA engine backs up with its cargo of containers in order to change tracks. The containers enclose segments of a solid rocket booster being returned to Utah for testing. The segments were part of the STS-114 stack. It is the first time actual flight segments that had been stacked for flight in the VAB are being returned for testing. They will undergo firing, which will enable inspectors to check the viability of the solid and verify the life expectancy for stacked segments.

Solid state production of polygalacturonase and xylanase by Trichoderma species using cantaloupe and watermelon rinds.

PubMed

Mohamed, Saleh A; Al-Malki, Abdulrahman L; Khan, Jalaluddin A; Kabli, Saleh A; Al-Garni, Saleh M

2013-10-01

Different solid state fermentation (SSF) sources were tested such as cantaloupe and watermelon rinds, orange and banana peels, for the production of polygalacturonase (PG) and xylanase (Xyl) by Trichoderma harzianum and Trichoderma virens. The maximum production of both PG and Xyl were obtained by T. harzianum and T. virnes grown on cantaloupe and watermelon rinds, respectively. Time course, moisture content, temperature, pH, supplementation with carbon and nitrogen sources were optimized to achieve the maximum production of both PG and Xyl of T. harzianum and T. virens using cantaloupe and watermelon rinds, respectively. The maximum production of PG and Xyl of T. harzianum and T. virens was recorded at 4-5 days of incubation, 50-66% moisture, temperature 28-35°C and pH 6-7. The influence of supplementary carbon and nitrogen sources was studied. For T. harzianum, lactose enhanced PG activity from 87 to 120 units/g solid, where starch and maltose enhanced Xyl activity from 40 to 55-60 units/g solid for T. virnes. Among the nitrogen sources, ammonium sulphate, ammonium nitrate, yeast extract and urea increased PG activity from 90 to 110-113 units/g solid for T. harzianum. Similarly, ammonium chloride, ammonium sulphate and yeast extract increased Xyl activity from 45 to 55-70 units/g solid for T. virens.

Survey of Sliding Contact/Solid Rail Power Collection Systems for Application to the Tracked Air Cushion Vehicle

DOT National Transportation Integrated Search

1971-01-01

The objective of a power collection system is to deliver uninterrupted power from the wayside to a vehicle. In order to apply the third rail concept, used for subway power collection, to the tracked air cushion vehicle, considerable improvement must ...

X-Ray Diffraction of Intermetallic Compounds: A Physical Chemistry Laboratory Experiment

ERIC Educational Resources Information Center

Varberg, Thomas D.; Skakuj, Kacper

2015-01-01

Here we describe an experiment for the undergraduate physical chemistry laboratory in which students synthesize the intermetallic compounds AlNi and AlNi3 and study them by X-ray diffractometry. The compounds are synthesized in a simple one-step reaction occurring in the solid state. Powder X-ray diffractograms are recorded for the two compounds…

Micro–mesoporous iron oxides with record efficiency for the decomposition of hydrogen peroxide: morphology driven catalysis for the degradation of organic contaminants

EPA Science Inventory

A template-free solid-state synthesis of a morphologically controlled and highly organized iron(III)oxide micro–mesoporous Fenton catalyst has been engineered through a simple two-step synthetic procedure. The 3D nanoassembly of hematite nanoparticles (5–7 nm) organized into a ro...

Fast, Capacious Disk Memory Device

NASA Technical Reports Server (NTRS)

Muller, Ronald M.

1990-01-01

Device for recording digital data on, and playing back data from, memory disks has high recording or playback rate and utilizes available recording area more fully. Two disks, each with own reading/writing head, used to record data at same time. Head on disk A operates on one of tracks numbered from outside in; head on disk B operates on track of same number in sequence from inside out. Underlying concept of device applicable to magnetic or optical disks.

Ionic liquids in drug delivery.

PubMed

Shamshina, Julia L; Barber, Patrick S; Rogers, Robin D

2013-10-01

To overcome potential problems with solid-state APIs, such as polymorphism, solubility and bioavailability, pure liquid salt (ionic liquid) forms of active pharmaceutical ingredients (API-ILs) are considered here as a design strategy. After a critical review of the current literature, the recent development of the API-ILs strategy is presented, with a particular focus on the liquefaction of drugs. A variety of IL tools for control over the liquid salt state of matter are discussed including choice of counterion to produce an IL from a given API; the concept of oligomeric ions that enables liquefaction of solid ILs by changing the stoichiometry or complexity of the ions; formation of 'liquid co-crystals' where hydrogen bonding is the driving force in the liquefaction of a neutral acid-base complex; combining an IL strategy with the prodrug strategy to improve the delivery of solid APIs; using ILs as delivery agents via trapping a drug in a micelle and finally ILs designed with tunable hydrophilic-lipophilic balance that matches the structural requirements needed to solubilize poorly water-soluble APIs. The authors believe that API-IL approaches may save failed lead candidates, extend the patent life of current APIs, lead to new delivery options or even new pharmaceutical action. They encourage the pharmaceutical industry to invest more research into the API-IL platform as it could lead to fast-tracked approval based on similarities to the APIs already approved.

Solid-state NMR calculations for metal oxides and gallates: shielding and quadrupolar parameters for perovskites and related phases.

PubMed

Middlemiss, Derek S; Blanc, Frédéric; Pickard, Chris J; Grey, Clare P

2010-05-01

The NMR parameters obtained from solid-state DFT calculations within the GIPAW approach for (17)O- and (69/71)Ga-sites in a range of predominantly oxide-based (group II monoxides, SrTiO(3), BaZrO(3), BaSnO(3), BaTiO(3), LaAlO(3), LaGaO(3), SrZrO(3), MgSiO(3) and Ba(2)In(2)O(5)), and gallate (alpha- and beta-Ga(2)O(3), LiGaO(2), NaGaO(2), GaPO(4) and LaGaO(3)) materials are compared with experimental values, with a view to the future application of a similar approach to doped phases of interest as candidate intermediate temperature solid oxide fuel cell (ITSOFC) electrolytes. Isotropic and anisotropic chemical shift parameters, quadrupolar coupling constants, and associated asymmetries are presented and analyzed. The unusual GaO(5) site occurring in LaGaGe(2)O(7) is also fully characterised. In general, it is found that the theoretical results closely track the experimental trends, though some deviations are identified and discussed, particularly in regard to quadrupolar eta(Q)-values. The high quality of the computed results suggests that this approach can be extended to study more complex and disordered phases. Copyright 2010 Elsevier Inc. All rights reserved.

Tetrapod tracks in Permo–Triassic eolian beds of southern Brazil (Paraná Basin)

PubMed Central

Dentzien-Dias, Paula; Lucas, Spencer G.; Schultz, Cesar L.

2018-01-01

Tetrapod tracks in eolianites are widespread in the fossil record since the late Paleozoic. Among these ichnofaunas, the ichnogenus Chelichnus is the most representative of the Permian tetrapod ichnological record of eolian deposits of Europe, North America and South America, where the Chelichnus Ichnofacies often occurs. In this contribution, we describe five sets of tracks (one of which is preserved in cross-section), representing the first occurrence of Dicynodontipus and Chelichnus in the “Pirambóia Formation” of southern Brazil. This unit represents a humid desert in southwestern Pangea and its lower and upper contacts lead us to consider its age as Lopingian–Induan. The five sets of tracks studied were compared with several ichnotaxa and body fossils with appendicular elements preserved, allowing us to attribute these tracks to dicynodonts and other indeterminate therapsids. Even though the “Pirambóia Formation” track record is sparse and sub-optimally preserved, it is an important key to better understand the occupation of arid environments by tetrapods across the Permo–Triassic boundary. PMID:29796341

Readout signals calculated for near-field optical pickups with land and groove recording.

PubMed

Saito, K; Kishima, K; Ichimura, I

2000-08-10

Optical disk readout signals with a solid immersion lens (SIL) and the land-groove recording technique are calculated by use of a simplified vector-diffraction theory. In this method the full vector-diffraction theory is applied to calculate the diffracted light from the initial state of the disk, and the light scattered from the recorded marks is regarded as a perturbation. Using this method, we confirmed that the land-groove recording technique is effective as a means of cross-talk reduction even when the numerical aperture is more than 1. However, the top surface of the disk under the SIL must be flat, or the readout signal from marks recorded on a groove decays when the optical depth of the groove is greater than lambda/8.

Reduced complexity of multi-track joint 2-D Viterbi detectors for bit-patterned media recording channel

NASA Astrophysics Data System (ADS)

Myint, L. M. M.; Warisarn, C.

2017-05-01

Two-dimensional (2-D) interference is one of the prominent challenges in ultra-high density recording system such as bit patterned media recording (BPMR). The multi-track joint 2-D detection technique with the help of the array-head reading can tackle this problem effectively by jointly processing the multiple readback signals from the adjacent tracks. Moreover, it can robustly alleviate the impairments due to track mis-registration (TMR) and media noise. However, the computational complexity of such detectors is normally too high and hard to implement in a reality, even for a few multiple tracks. Therefore, in this paper, we mainly focus on reducing the complexity of multi-track joint 2-D Viterbi detector without paying a large penalty in terms of the performance. We propose a simplified multi-track joint 2-D Viterbi detector with a manageable complexity level for the BPMR's multi-track multi-head (MTMH) system. In the proposed method, the complexity of detector's trellis is reduced with the help of the joint-track equalization method which employs 1-D equalizers and 2-D generalized partial response (GPR) target. Moreover, we also examine the performance of a full-fledged multi-track joint 2-D detector and the conventional 2-D detection. The results show that the simplified detector can perform close to the full-fledge detector, especially when the system faces high media noise, with the significant low complexity.

Global Distribution of Solid Ammonium Sulfate Aerosols and their Climate Impact Acting as Ice Nuclei

NASA Astrophysics Data System (ADS)

Zhou, C.; Penner, J.

2017-12-01

Laboratory experiments show that liquid ammonium sulfate particles effloresce when RHw is below 34% to become solid and dissolve when RHw is above 79%. Solid ammonium sulfate aerosols can act as heterogeneous ice nuclei particles (INPs) to form ice particles in deposition mode when the relative humidity over ice is above 120%. In this study we used the coupled IMPACT/CAM5 model to track the efflorescence and deliquescence processes of ammonium sulfate. Results show that about 20% of the total simulated pure sulfate aerosol mass is in the solid state and is mainly distributed in the northern hemisphere (NH) from 50 hPa to 200 hPa. When these solid ammonium sulfate aerosols are allowed to act as ice nuclei particles, they act to increase the ice water path in the NH and reduce ice water path in the tropics. The addition of these particles leads to a positive net radiative effect at the TOA ranging from 0.5-0.9 W/m2 depending on the amounts of other ice nuclei particles (e.g., dust, soot) used in the ice nucleation process. The short-term climate feedback shows that the ITCZ shifts northwards and precipitation increases in the NH. There is also an average warming of 0.05-0.1 K near the surface (at 2 meter) in the NH which is most obvious in the Arctic region.

Big Data Provenance: Challenges, State of the Art and Opportunities.

PubMed

Wang, Jianwu; Crawl, Daniel; Purawat, Shweta; Nguyen, Mai; Altintas, Ilkay

2015-01-01

Ability to track provenance is a key feature of scientific workflows to support data lineage and reproducibility. The challenges that are introduced by the volume, variety and velocity of Big Data, also pose related challenges for provenance and quality of Big Data, defined as veracity. The increasing size and variety of distributed Big Data provenance information bring new technical challenges and opportunities throughout the provenance lifecycle including recording, querying, sharing and utilization. This paper discusses the challenges and opportunities of Big Data provenance related to the veracity of the datasets themselves and the provenance of the analytical processes that analyze these datasets. It also explains our current efforts towards tracking and utilizing Big Data provenance using workflows as a programming model to analyze Big Data.

78 FR 54445 - Privacy Act Systems of Records; Phytosanitary Certificate Issuance and Tracking System

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-04

...We are withdrawing a Privacy Act System of Records notice published on August 9, 2013, (78 FR 48642-48644). The system of records was the Phytosanitary Certificate Issuance and Tracking System, USDA- APHIS-13. The August 9, 2013, notice was a duplicate notice published in error; in this document, we are withdrawing the August 9, 2013, notice from publication.

Effect of cross-correlation on track-to-track fusion

NASA Astrophysics Data System (ADS)

Saha, Rajat K.

1994-07-01

Since the advent of target tracking systems employing a diverse mixture of sensors, there has been increasing recognition by air defense system planners and other military system analysts of the need to integrate these tracks so that a clear air picture can be obtained in a command center. A popular methodology to achieve this goal is to perform track-to-track fusion, which performs track-to-track association as well as kinematic state vector fusion. This paper seeks to answer analytically the extent of improvement achievable by means of kinetic state vector fusion when the tracks are obtained from dissimilar sensors (e.g., Radar/ESM/IRST/IFF). It is well known that evaluation of the performance of state vector fusion algorithms at steady state must take into account the effects of cross-correlation between eligible tracks introduced by the input noise which, unfortunately, is often neglected because of added computational complexity. In this paper, an expression for the steady-state cross-covariance matrix for a 2D state vector track-to-track fusion is obtained. This matrix is shown to be a function of the parameters of the Kalman filters associated with the candidate tracks being fused. Conditions for positive definiteness of the cross-covariance matrix have been derived and the effect of positive definiteness on performance of track-to-track fusion is also discussed.

Ultrafast quantum control of ionization dynamics in krypton.

PubMed

Hütten, Konrad; Mittermair, Michael; Stock, Sebastian O; Beerwerth, Randolf; Shirvanyan, Vahe; Riemensberger, Johann; Duensing, Andreas; Heider, Rupert; Wagner, Martin S; Guggenmos, Alexander; Fritzsche, Stephan; Kabachnik, Nikolay M; Kienberger, Reinhard; Bernhardt, Birgitta

2018-02-19

Ultrafast spectroscopy with attosecond resolution has enabled the real time observation of ultrafast electron dynamics in atoms, molecules and solids. These experiments employ attosecond pulses or pulse trains and explore dynamical processes in a pump-probe scheme that is selectively sensitive to electronic state of matter via photoelectron or XUV absorption spectroscopy or that includes changes of the ionic state detected via photo-ion mass spectrometry. Here, we demonstrate how the implementation of combined photo-ion and absorption spectroscopy with attosecond resolution enables tracking the complex multidimensional excitation and decay cascade of an Auger auto-ionization process of a few femtoseconds in highly excited krypton. In tandem with theory, our study reveals the role of intermediate electronic states in the formation of multiply charged ions. Amplitude tuning of a dressing laser field addresses different groups of decay channels and allows exerting temporal and quantitative control over the ionization dynamics in rare gas atoms.

Electrical probing of field-driven cascading quantized transitions of skyrmion cluster states in MnSi nanowires

NASA Astrophysics Data System (ADS)

Du, Haifeng; Liang, Dong; Jin, Chiming; Kong, Lingyao; Stolt, Matthew J.; Ning, Wei; Yang, Jiyong; Xing, Ying; Wang, Jian; Che, Renchao; Zang, Jiadong; Jin, Song; Zhang, Yuheng; Tian, Mingliang

2015-07-01

Magnetic skyrmions are topologically stable whirlpool-like spin textures that offer great promise as information carriers for future spintronic devices. To enable such applications, particular attention has been focused on the properties of skyrmions in highly confined geometries such as one-dimensional nanowires. Hitherto, it is still experimentally unclear what happens when the width of the nanowire is comparable to that of a single skyrmion. Here, we achieve this by measuring the magnetoresistance in ultra-narrow MnSi nanowires. We observe quantized jumps in magnetoresistance versus magnetic field curves. By tracking the size dependence of the jump number, we infer that skyrmions are assembled into cluster states with a tunable number of skyrmions, in agreement with the Monte Carlo simulations. Our results enable an electric reading of the number of skyrmions in the cluster states, thus laying a solid foundation to realize skyrmion-based memory devices.

Optical Tracker For Longwall Coal Shearer

NASA Technical Reports Server (NTRS)

Poulsen, Peter D.; Stein, Richard J.; Pease, Robert E.

1989-01-01

Photographic record yields information for correction of vehicle path. Tracking system records lateral movements of longwall coal-shearing vehicle. System detects lateral and vertical deviations of path of vehicle moving along coal face, shearing coal as it goes. Rides on rails in mine tunnel, advancing on toothed track in one of rails. As vehicle moves, retroreflective mirror rides up and down on teeth, providing series of pulsed reflections to film recorder. Recorded positions of pulses, having horizontal and vertical orientations, indicate vertical and horizontal deviations, respectively, of vehicle.

Fine Structure of the Outermost Solid Core from Analysis of PKiKP Coda Waves

NASA Astrophysics Data System (ADS)

Krasnoshchekov, D.; Kaazik, P.; Ovtchinnikov, V.

2006-05-01

Near surface heterogeneities in the Earth's inner core have recently been confirmed to exist, and pods of partial melt or variations in seismic anisotropy either due to orientation of iron crystals or changes in strength were indicated as possible sources for such peculiarities. In the same time, analysis of the phase reflected from the inner core boundary (PKiKP) predicts complex character of the reflecting discontinuity in the form of local thin transition layers resulting in mosaic structure of the Earth's inner core's surface. Precritical PKiKP waveforms and coda waves provide necessary seismological constraints to investigate fine structure of the upper part of the Earth's inner core and its boundary, and rank high among researches that detected the described specifics of the solid core. PKiKP coda studies have to do with weak amplitudes and subtle effects, which frequently requires using a reference core related seismic phase and array data processing, as well as eliminating max number of factors biasing the resulting estimates (for example, source related inaccuracies typical for earthquake analysis). In this work we report new observations of PKiKP coda waves detected on records of a group of Underground Nuclear Explosions (UNEs) carried out in USSR and recorded at distances from 6 to 95 degrees by stations of the world seismological network. Our dataset benefits from using accurate ground truth information on source parameters (locations, origin times, depths, etc.), requires no accounting for different source radiation patterns and contains records corresponding to the whole range of precritical reflection including so called transparent zone where amplitudes of direct PKiKP phase are negligible. The processed dataset incorporates records of the array of sources consisted of the same magnitude explosions closely carried out at Semipalatinsk Test Site and recorded by stations located in Eurasia, Africa and North America. We detect PKiKP coda waves on records of all stations that registered this array. The performed frequency-wavenumber analysis and stacking of the array data reveal both scattering mechanism tracked in the form of slight dependence of PKiKP coda's frequency content on epicentral distance, and reflective mechanism evidenced by detection of distinct arrivals of waves reflected from isotropic or anisotropic discontinuities below the inner core boundary. We infer, that PKiKP coda is built by both volumetric scattering and reverberations on reflectors in the upper portion of the inner core. We also find no significant evidence for the presence of a constant depth global isotropic reflector all through 300 km below the ICB and attribute different types of the observed PKiKP coda patterns to variability in properties of the outermost portion of the Earth's inner core either due to its anisotropy or local specifics. The research described was made possible in part by contribution from grant RUG1-2675-MO-05 of the US Civilian Research & Development Foundation for the Independent States of the Former Soviet Union (CRDF) and the President Grant MK-1600.2005.5.

49 CFR 1507.3 - Exemptions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... exempt from the access provisions of subsection (d). (e) Correspondence and Matters Tracking Records (DHS/TSA 006). The Correspondence and Matters Tracking Records (CMTR) (DHS/TSA 006) system allows TSA to... is not always possible for TSA or other agencies to know in advance what information is both relevant...

Infants Make Quantity Discriminations for Substances

ERIC Educational Resources Information Center

Hespos, Susan J.; Dora, Begum; Rips, Lance J.; Christie, Stella

2012-01-01

Infants can track small groups of solid objects, and infants can respond when these quantities change. But earlier work is equivocal about whether infants can track continuous substances, such as piles of sand. Experiment 1 ("N" = 88) used a habituation paradigm to show infants can register changes in the size of piles of sand that they…

Bayesian source tracking via focalization and marginalization in an uncertain Mediterranean Sea environment.

PubMed

Dosso, Stan E; Wilmut, Michael J; Nielsen, Peter L

2010-07-01

This paper applies Bayesian source tracking in an uncertain environment to Mediterranean Sea data, and investigates the resulting tracks and track uncertainties as a function of data information content (number of data time-segments, number of frequencies, and signal-to-noise ratio) and of prior information (environmental uncertainties and source-velocity constraints). To track low-level sources, acoustic data recorded for multiple time segments (corresponding to multiple source positions along the track) are inverted simultaneously. Environmental uncertainty is addressed by including unknown water-column and seabed properties as nuisance parameters in an augmented inversion. Two approaches are considered: Focalization-tracking maximizes the posterior probability density (PPD) over the unknown source and environmental parameters. Marginalization-tracking integrates the PPD over environmental parameters to obtain a sequence of joint marginal probability distributions over source coordinates, from which the most-probable track and track uncertainties can be extracted. Both approaches apply track constraints on the maximum allowable vertical and radial source velocity. The two approaches are applied for towed-source acoustic data recorded at a vertical line array at a shallow-water test site in the Mediterranean Sea where previous geoacoustic studies have been carried out.

Technical Report of the Use of a Novel Eye Tracking System to Measure Impairment Associated with Mild Traumatic Brain Injury

PubMed Central

2017-01-01

This technical report details the results of an uncontrolled study of EyeGuide Focus, a 10-second concussion management tool which relies on eye tracking to determine the potential impairment of visual attention, an indicator often of mild traumatic brain injury (mTBI). Essentially, people who can visually keep steady and accurate attention on a moving object in their environment likely suffer from no impairment. However, if after a potential mTBI event, subjects cannot keep attention on a moving object in a normal way as demonstrated on their previous healthy baseline tests. This may indicate possible neurological impairment. Now deployed at multiple locations across the United States, Focus (EyeGuide, Lubbock, Texas, United States) to date, has recorded more than 4,000 test scores. Our data analysis of these results shows the promise of Focus as a low-cost, ocular-based impairment test for assessing potential neurological impairment caused by mTBI in subjects ages eight and older.  PMID:28630809

Technical Report of the Use of a Novel Eye Tracking System to Measure Impairment Associated with Mild Traumatic Brain Injury.

PubMed

Kelly, Michael

2017-05-15

This technical report details the results of an uncontrolled study of EyeGuide Focus, a 10-second concussion management tool which relies on eye tracking to determine the potential impairment of visual attention, an indicator often of mild traumatic brain injury (mTBI). Essentially, people who can visually keep steady and accurate attention on a moving object in their environment likely suffer from no impairment. However, if after a potential mTBI event, subjects cannot keep attention on a moving object in a normal way as demonstrated on their previous healthy baseline tests. This may indicate possible neurological impairment. Now deployed at multiple locations across the United States, Focus (EyeGuide, Lubbock, Texas, United States) to date, has recorded more than 4,000 test scores. Our data analysis of these results shows the promise of Focus as a low-cost, ocular-based impairment test for assessing potential neurological impairment caused by mTBI in subjects ages eight and older.

The Origin and Early Radiation of Archosauriforms: Integrating the Skeletal and Footprint Record.

PubMed

Bernardi, Massimo; Klein, Hendrik; Petti, Fabio Massimo; Ezcurra, Martín D

2015-01-01

We present a holistic approach to the study of early archosauriform evolution by integrating body and track records. The ichnological record supports a Late Permian-Early Triassic radiation of archosauriforms not well documented by skeletal material, and new footprints from the Upper Permian of the southern Alps (Italy) provide evidence for a diversity not yet sampled by body fossils. The integrative study of body fossil and footprint data supports the hypothesis that archosauriforms had already undergone substantial taxonomic diversification by the Late Permian and that by the Early Triassic archosauromorphs attained a broad geographical distribution over most parts of Pangea. Analysis of body size, as deduced from track size, suggests that archosauriform average body size did not change significantly from the Late Permian to the Early Triassic. A survey of facies yielding both skeletal and track record indicate an ecological preference for inland fluvial (lacustrine) environments for early archosauromorphs. Finally, although more data is needed, Late Permian chirotheriid imprints suggest a shift from sprawling to erect posture in archosauriforms before the end-Permian mass extinction event. We highlight the importance of approaching palaeobiological questions by using all available sources of data, specifically through integrating the body and track fossil record.

The Origin and Early Radiation of Archosauriforms: Integrating the Skeletal and Footprint Record

PubMed Central

Bernardi, Massimo; Klein, Hendrik; Petti, Fabio Massimo; Ezcurra, Martín D.

2015-01-01

We present a holistic approach to the study of early archosauriform evolution by integrating body and track records. The ichnological record supports a Late Permian–Early Triassic radiation of archosauriforms not well documented by skeletal material, and new footprints from the Upper Permian of the southern Alps (Italy) provide evidence for a diversity not yet sampled by body fossils. The integrative study of body fossil and footprint data supports the hypothesis that archosauriforms had already undergone substantial taxonomic diversification by the Late Permian and that by the Early Triassic archosauromorphs attained a broad geographical distribution over most parts of Pangea. Analysis of body size, as deduced from track size, suggests that archosauriform average body size did not change significantly from the Late Permian to the Early Triassic. A survey of facies yielding both skeletal and track record indicate an ecological preference for inland fluvial (lacustrine) environments for early archosauromorphs. Finally, although more data is needed, Late Permian chirotheriid imprints suggest a shift from sprawling to erect posture in archosauriforms before the end-Permian mass extinction event. We highlight the importance of approaching palaeobiological questions by using all available sources of data, specifically through integrating the body and track fossil record. PMID:26083612

Revised Extended Grid Library

DOE Office of Scientific and Technical Information (OSTI.GOV)

Martz, Roger L.

The Revised Eolus Grid Library (REGL) is a mesh-tracking library that was developed for use with the MCNP6TM computer code so that (radiation) particles can track on an unstructured mesh. The unstructured mesh is a finite element representation of any geometric solid model created with a state-of-the-art CAE/CAD tool. The mesh-tracking library is written using modern Fortran and programming standards; the library is Fortran 2003 compliant. The library was created with a defined application programmer interface (API) so that it could easily integrate with other particle tracking/transport codes. The library does not handle parallel processing via the message passing interfacemore » (mpi), but has been used successfully where the host code handles the mpi calls. The library is thread-safe and supports the OpenMP paradigm. As a library, all features are available through the API and overall a tight coupling between it and the host code is required. Features of the library are summarized with the following list: Can accommodate first and second order 4, 5, and 6-sided polyhedra; any combination of element types may appear in a single geometry model; parts may not contain tetrahedra mixed with other element types; pentahedra and hexahedra can be together in the same part; robust handling of overlaps and gaps; tracks element-to-element to produce path length results at the element level; finds element numbers for a given mesh location; finds intersection points on element faces for the particle tracks; produce a data file for post processing results analysis; reads Abaqus .inp input (ASCII) files to obtain information for the global mesh-model; supports parallel input processing via mpi; and support parallel particle transport by both mpi and OpenMP.« less

Combining particle-tracking and geochemical data to assess public supply well vulnerability to arsenic and uranium

USGS Publications Warehouse

Hinkle, S.R.; Kauffman, L.J.; Thomas, M.A.; Brown, C.J.; McCarthy, K.A.; Eberts, S.M.; Rosen, Michael R.; Katz, B.G.

2009-01-01

Flow-model particle-tracking results and geochemical data from seven study areas across the United States were analyzed using three statistical methods to test the hypothesis that these variables can successfully be used to assess public supply well vulnerability to arsenic and uranium. Principal components analysis indicated that arsenic and uranium concentrations were associated with particle-tracking variables that simulate time of travel and water fluxes through aquifer systems and also through specific redox and pH zones within aquifers. Time-of-travel variables are important because many geochemical reactions are kinetically limited, and geochemical zonation can account for different modes of mobilization and fate. Spearman correlation analysis established statistical significance for correlations of arsenic and uranium concentrations with variables derived using the particle-tracking routines. Correlations between uranium concentrations and particle-tracking variables were generally strongest for variables computed for distinct redox zones. Classification tree analysis on arsenic concentrations yielded a quantitative categorical model using time-of-travel variables and solid-phase-arsenic concentrations. The classification tree model accuracy on the learning data subset was 70%, and on the testing data subset, 79%, demonstrating one application in which particle-tracking variables can be used predictively in a quantitative screening-level assessment of public supply well vulnerability. Ground-water management actions that are based on avoidance of young ground water, reflecting the premise that young ground water is more vulnerable to anthropogenic contaminants than is old ground water, may inadvertently lead to increased vulnerability to natural contaminants due to the tendency for concentrations of many natural contaminants to increase with increasing ground-water residence time.

FAST TRACK COMMUNICATION Unexpected systematic degeneracy in a system of two coupled Gaudin models with homogeneous couplings

NASA Astrophysics Data System (ADS)

Erbe, B.; Schliemann, J.

2010-12-01

We report an unexpected systematic degeneracy between different multiplets in an inversion symmetric system of two coupled Gaudin models with homogeneous couplings, as occurring for example in the context of solid state quantum information processing. We construct the full degenerate subspace (being of macroscopic dimension), which turns out to lie in the kernel of the commutator between the two Gaudin models and the coupling term. Finally we investigate to what extent the degeneracy is related to the inversion symmetry of the system and find that indeed there is a large class of systems showing the same type of degeneracy.

Space Shuttle propulsion performance reconstruction from flight data

NASA Technical Reports Server (NTRS)

Rogers, Robert M.

1989-01-01

The aplication of extended Kalman filtering to estimating Space Shuttle Solid Rocket Booster (SRB) performance, specific impulse, from flight data in a post-flight processing computer program. The flight data used includes inertial platform acceleration, SRB head pressure, and ground based radar tracking data. The key feature in this application is the model used for the SRBs, which represents a reference quasi-static internal ballistics model normalized to the propellant burn depth. Dynamic states of mass overboard and propellant burn depth are included in the filter model to account for real-time deviations from the reference model used. Aerodynamic, plume, wind and main engine uncertainties are included.

Mixed-Mode Decohesion Elements for Analyses of Progressive Delamination

NASA Technical Reports Server (NTRS)

Davila, Carlos G.; Camanho, Pedro P.; deMoura, Marcelo F.

2001-01-01

A new 8-node decohesion element with mixed mode capability is proposed and demonstrated. The element is used at the interface between solid finite elements to model the initiation and propagation of delamination. A single displacement-based damage parameter is used in a strain softening law to track the damage state of the interface. The method can be used in conjunction with conventional material degradation procedures to account for inplane and intra-laminar damage modes. The accuracy of the predictions is evaluated in single mode delamination tests, in the mixed-mode bending test, and in a structural configuration consisting of the debonding of a stiffener flange from its skin.

Room temperature solid-state quantum emitters in the telecom range.

PubMed

Zhou, Yu; Wang, Ziyu; Rasmita, Abdullah; Kim, Sejeong; Berhane, Amanuel; Bodrog, Zoltán; Adamo, Giorgio; Gali, Adam; Aharonovich, Igor; Gao, Wei-Bo

2018-03-01

On-demand, single-photon emitters (SPEs) play a key role across a broad range of quantum technologies. In quantum networks and quantum key distribution protocols, where photons are used as flying qubits, telecom wavelength operation is preferred because of the reduced fiber loss. However, despite the tremendous efforts to develop various triggered SPE platforms, a robust source of triggered SPEs operating at room temperature and the telecom wavelength is still missing. We report a triggered, optically stable, room temperature solid-state SPE operating at telecom wavelengths. The emitters exhibit high photon purity (~5% multiphoton events) and a record-high brightness of ~1.5 MHz. The emission is attributed to localized defects in a gallium nitride (GaN) crystal. The high-performance SPEs embedded in a technologically mature semiconductor are promising for on-chip quantum simulators and practical quantum communication technologies.

Calibrations for Charged Particle Tracking with the GlueX Detector

NASA Astrophysics Data System (ADS)

Staib, Michael; GlueX Collaboration

2015-10-01

Two gas detectors comprise the tracking system for the GlueX experiment, the Central Drift Chamber (CDC) and the Forward Drift Chamber (FDC). The CDC is a cylindrical straw-tube detector covering polar angles between 6° and 168°, delivering spatial resolution of ~150 μm. The FDC is a Cathode Strip Chamber consisting of four packages, each with six alternating layers of anode wires and cathode strips. The FDC is designed to track forward-going charged particles with polar angles between 1° and 20° with a spatial resolution of ~200 μm. Both tracking detectors record timing information and energy loss measurements useful for particle identification. During Fall 2014 and Spring 2015, the first photon beam was delivered on target for commissioning of the GlueX detector in Hall-D at Jefferson Lab. These data are currently being used in a large effort to calibrate the individual detector subsystems to achieve design performance. Methods and results for calibrations of each of the tracking detectors are presented. Techniques for alignment of the tracking system using a combination of cosmic rays and beam data is discussed. Finally, some early results of physics measurements including charged final-state particles are presented. This material is based upon work supported by the U.S. Department of Energy, Office of Science, Office of Nuclear Physics under Contract DE-AC05-06OR23177.

The use of ultrasonic properties of CR-39 track detectors in neutron dosimetry

NASA Astrophysics Data System (ADS)

Afifi, H.; El-Sersy, A.; Khaled, N.

2004-01-01

The longitudinal and shear wave ultrasonic velocities have been measured before and after exposing 5-mm thick CR-39 solid state nuclear track detectors to both a mixed field of gamma-rays and fast neutrons from an Am-Be source in the ranges from 0 to 10 4 mSv. The change in the intermolecular structure as caused by the fast neutron exposure was studied by the ultrasonic pulse echo method at a frequency of 2 MHz and at room temperature. The elastic coefficients, Poisson's ratio, microhardness, ultrasonic absorption coefficient and internal friction have been determined. The study shows that the gamma-ray irradiation had no effect on the ultrasonic properties of CR-39 at least at the used doses. However, all the ultrasonic properties are influenced by the fast neutrons at doses up to 10 4 mSv. Our experimental results confirmed that the ultrasonic technique is useful for fast neutron detection, by exploiting the differences in mechanical properties of CR-39.

Measurement of radon exhalation rate in various building materials and soil samples

NASA Astrophysics Data System (ADS)

Bala, Pankaj; Kumar, Vinod; Mehra, Rohit

2017-03-01

Indoor radon is considered as one of the potential dangerous radioactive elements. Common building materials and soil are the major source of this radon gas in the indoor environment. In the present study, the measurement of radon exhalation rate in the soil and building material samples of Una and Hamirpur districts of Himachal Pradesh has been done with solid state alpha track detectors, LR-115 type-II plastic track detectors. The radon exhalation rate for the soil samples varies from 39.1 to 91.2 mBq kg-1 h-1 with a mean value 59.7 mBq kg-1 h-1. Also the radium concentration of the studied area is found and it varies from 30.6 to 51.9 Bq kg-1 with a mean value 41.6 Bq kg-1. The exhalation rate for the building material samples varies from 40.72 (sandstone) to 81.40 mBq kg-1 h-1 (granite) with a mean value of 59.94 mBq kg-1 h-1.

Development of bubble memory recorder onboard Japan Earth Resources Satellite-1

NASA Astrophysics Data System (ADS)

Araki, Tsunehiko; Ishida, Chu; Ochiai, Kiyoshi; Nozue, Tatsuhiro; Tachibana, Kyozo; Yoshida, Kazutoshi

The Bubble Memory Recorder (BMR) developed for use on the Earth Resources Satellite is described in terms of its design, capabilities, and functions. The specifications of the BMR are given listing memory capacity, functions, and interface types for data, command, and telemetry functions. The BMR has an emergency signal interface to provide contingency recording, and a satellite-separation signal interface can be turned on automatically by signal input. Data are stored in a novolatile memory device so that the memory is retained during power outages. The BMR is characterized by a capability for random access, nonvolatility, and a solid-state design that is useful for space operations since it does not disturb spacecraft attitude.

GPS tracking data of Lesser Black-backed Gulls and Herring Gulls breeding at the southern North Sea coast.

PubMed

Stienen, Eric W M; Desmet, Peter; Aelterman, Bart; Courtens, Wouter; Feys, Simon; Vanermen, Nicolas; Verstraete, Hilbran; de Walle, Marc Van; Deneudt, Klaas; Hernandez, Francisco; Houthoofdt, Robin; Vanhoorne, Bart; Bouten, Willem; Buijs, Roland-Jan; Kavelaars, Marwa M; Müller, Wendt; Herman, David; Matheve, Hans; Sotillo, Alejandro; Lens, Luc

2016-01-01

In this data paper, Bird tracking - GPS tracking of Lesser Black-backed Gulls and Herring Gulls breeding at the southern North Sea coast is described, a species occurrence dataset published by the Research Institute for Nature and Forest (INBO). The dataset (version 5.5) contains close to 2.5 million occurrences, recorded by 101 GPS trackers mounted on 75 Lesser Black-backed Gulls and 26 Herring Gulls breeding at the Belgian and Dutch coast. The trackers were developed by the University of Amsterdam Bird Tracking System (UvA-BiTS, http://www.uva-bits.nl). These automatically record and transmit bird movements, which allows us and others to study their habitat use and migration behaviour in great detail. Our bird tracking network is operational since 2013. It is funded for LifeWatch by the Hercules Foundation and maintained in collaboration with UvA-BiTS and the Flanders Marine Institute (VLIZ). The recorded data are periodically released in bulk as open data (http://dataset.inbo.be/bird-tracking-gull-occurrences), and are also accessible through CartoDB and the Global Biodiversity Information Facility (GBIF).

Research leadership: should clinical directors be distinguished researchers?

PubMed

Allison, Stephen; Goodall, Amanda H; Bastiampillai, Tarun

2016-06-01

Clinical directors established research-led healthcare by combining research, teaching and clinical excellence within the teaching hospitals. This research culture created high clinical standards, which benefited patients, the workforce and healthcare organisations. The current paper explores this research leadership role for clinical directors. It reviews studies arising from the theory of expert leadership, which focuses on the relationship between a leader's core knowledge and organisational performance. More specifically, we examine the expert leader's research track record, the associations with their organisation's performance, and the influence of research activity on clinical excellence. Distinguished researchers still lead the most prestigious teaching hospitals and the most trusted departments of psychiatry in the United States where the clinical directorate structure originated. It is also known that good scholars can improve research output when appointed to leadership positions. This suggests that the clinical director's research track record should be a consideration at a time when research is being embedded in Australia's local health networks. A clinical director's leadership may influence the research performance of their department and contribute to the quality of mental healthcare. © The Royal Australian and New Zealand College of Psychiatrists 2015.

Flood-tracking chart for the Withlacoochee and Little River Basins in south-central Georgia and northern Florida

USGS Publications Warehouse

Gotvald, Anthony J.; McCallum, Brian E.; Painter, Jaime A.

2014-01-01

The U.S. Geological Survey (USGS), in cooperation with other Federal, State, and local agencies, operates a flood-monitoring system in the Withlacoochee and Little River Basins. This system is a network of automated river stage stations (ten are shown on page 2 of this publication) that transmit stage data through satellite telemetry to the USGS in Atlanta, Georgia and the National Weather Service (NWS) in Peachtree City, Georgia. During floods, the public and emergency response agencies use this information to make decisions about road closures, evacuations, and other public safety issues. This Withlacoochee and Little River Basins flood-tracking chart can be used by local citizens and emergency response personnel to record the latest river stage and predicted flood-crest information along the Withlacoochee River, Little River, and Okapilco Creek in south-central Georgia and northern Florida. By comparing the current stage (water-surface level above a datum) and predicted flood crest to the recorded peak stages of previous floods, emergency response personnel and residents can make informed decisions concerning the threat to life and property.

Near Real-Time Surveillance of U.S. Norovirus Outbreaks by the Norovirus Sentinel Testing and Tracking Network - United States, August 2009-July 2015.

PubMed

Shah, Minesh P; Wikswo, Mary E; Barclay, Leslie; Kambhampati, Anita; Shioda, Kayoko; Parashar, Umesh D; Vinjé, Jan; Hall, Aron J

2017-02-24

Norovirus is the leading cause of endemic and epidemic acute gastroenteritis in the United States (1). New variant strains of norovirus GII.4 emerge every 2-4 years (2-4) and are often associated with increased disease and health care visits (5-7). Since 2009, CDC has obtained epidemiologic data on norovirus outbreaks from state health departments through the National Outbreak Reporting System (NORS) (8) and laboratory data through CaliciNet (9). NORS is a web-based platform for reporting waterborne, foodborne, and enteric disease outbreaks of all etiologies, including norovirus, to CDC. CaliciNet, a nationwide electronic surveillance system of local and state public health and regulatory agency laboratories, collects genetic sequences of norovirus strains associated with gastroenteritis outbreaks. Because these two independent reporting systems contain complementary data, integration of NORS and CaliciNet records could provide valuable public health information about norovirus outbreaks. However, reporting lags and inconsistent identification codes in NORS and CaliciNet records have been an obstacle to developing an integrated surveillance system.

78 FR 12298 - Privacy Act of 1974; System of Records-School Participation Division Complaints Tracking System

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-22

... Complaints Tracking System AGENCY: Federal Student Aid, Department of Education. ACTION: Notice of a new... Division Complaints Tracking System (SPD-CTS)'' (18-11- 19). DATES: Submit your comments on this proposed... all comments about the School Participation Division--Complaints Tracking System to: Performance...

Two paths to blame: Intentionality directs moral information processing along two distinct tracks.

PubMed

Monroe, Andrew E; Malle, Bertram F

2017-01-01

There is broad consensus that features such as causality, mental states, and preventability are key inputs to moral judgments of blame. What is not clear is exactly how people process these inputs to arrive at such judgments. Three studies provide evidence that early judgments of whether or not a norm violation is intentional direct information processing along 1 of 2 tracks: if the violation is deemed intentional, blame processing relies on information about the agent's reasons for committing the violation; if the violation is deemed unintentional, blame processing relies on information about how preventable the violation was. Owing to these processing commitments, when new information requires perceivers to switch tracks, they must reconfigure their judgments, which results in measurable processing costs indicated by reaction time (RT) delays. These findings offer support for a new theory of moral judgment (the Path Model of Blame) and advance the study of moral cognition as hierarchical information processing. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

Video-based measurements for wireless capsule endoscope tracking

NASA Astrophysics Data System (ADS)

Spyrou, Evaggelos; Iakovidis, Dimitris K.

2014-01-01

The wireless capsule endoscope is a swallowable medical device equipped with a miniature camera enabling the visual examination of the gastrointestinal (GI) tract. It wirelessly transmits thousands of images to an external video recording system, while its location and orientation are being tracked approximately by external sensor arrays. In this paper we investigate a video-based approach to tracking the capsule endoscope without requiring any external equipment. The proposed method involves extraction of speeded up robust features from video frames, registration of consecutive frames based on the random sample consensus algorithm, and estimation of the displacement and rotation of interest points within these frames. The results obtained by the application of this method on wireless capsule endoscopy videos indicate its effectiveness and improved performance over the state of the art. The findings of this research pave the way for a cost-effective localization and travel distance measurement of capsule endoscopes in the GI tract, which could contribute in the planning of more accurate surgical interventions.

Efficient integration of spectral features for vehicle tracking utilizing an adaptive sensor

NASA Astrophysics Data System (ADS)

Uzkent, Burak; Hoffman, Matthew J.; Vodacek, Anthony

2015-03-01

Object tracking in urban environments is an important and challenging problem that is traditionally tackled using visible and near infrared wavelengths. By inserting extended data such as spectral features of the objects one can improve the reliability of the identification process. However, huge increase in data created by hyperspectral imaging is usually prohibitive. To overcome the complexity problem, we propose a persistent air-to-ground target tracking system inspired by a state-of-the-art, adaptive, multi-modal sensor. The adaptive sensor is capable of providing panchromatic images as well as the spectra of desired pixels. This addresses the data challenge of hyperspectral tracking by only recording spectral data as needed. Spectral likelihoods are integrated into a data association algorithm in a Bayesian fashion to minimize the likelihood of misidentification. A framework for controlling spectral data collection is developed by incorporating motion segmentation information and prior information from a Gaussian Sum filter (GSF) movement predictions from a multi-model forecasting set. An intersection mask of the surveillance area is extracted from OpenStreetMap source and incorporated into the tracking algorithm to perform online refinement of multiple model set. The proposed system is tested using challenging and realistic scenarios generated in an adverse environment.

Deterministic object tracking using Gaussian ringlet and directional edge features

NASA Astrophysics Data System (ADS)

Krieger, Evan W.; Sidike, Paheding; Aspiras, Theus; Asari, Vijayan K.

2017-10-01

Challenges currently existing for intensity-based histogram feature tracking methods in wide area motion imagery (WAMI) data include object structural information distortions, background variations, and object scale change. These issues are caused by different pavement or ground types and from changing the sensor or altitude. All of these challenges need to be overcome in order to have a robust object tracker, while attaining a computation time appropriate for real-time processing. To achieve this, we present a novel method, Directional Ringlet Intensity Feature Transform (DRIFT), which employs Kirsch kernel filtering for edge features and a ringlet feature mapping for rotational invariance. The method also includes an automatic scale change component to obtain accurate object boundaries and improvements for lowering computation times. We evaluated the DRIFT algorithm on two challenging WAMI datasets, namely Columbus Large Image Format (CLIF) and Large Area Image Recorder (LAIR), to evaluate its robustness and efficiency. Additional evaluations on general tracking video sequences are performed using the Visual Tracker Benchmark and Visual Object Tracking 2014 databases to demonstrate the algorithms ability with additional challenges in long complex sequences including scale change. Experimental results show that the proposed approach yields competitive results compared to state-of-the-art object tracking methods on the testing datasets.

A point process approach to identifying and tracking transitions in neural spiking dynamics in the subthalamic nucleus of Parkinson's patients

NASA Astrophysics Data System (ADS)

Deng, Xinyi; Eskandar, Emad N.; Eden, Uri T.

2013-12-01

Understanding the role of rhythmic dynamics in normal and diseased brain function is an important area of research in neural electrophysiology. Identifying and tracking changes in rhythms associated with spike trains present an additional challenge, because standard approaches for continuous-valued neural recordings—such as local field potential, magnetoencephalography, and electroencephalography data—require assumptions that do not typically hold for point process data. Additionally, subtle changes in the history dependent structure of a spike train have been shown to lead to robust changes in rhythmic firing patterns. Here, we propose a point process modeling framework to characterize the rhythmic spiking dynamics in spike trains, test for statistically significant changes to those dynamics, and track the temporal evolution of such changes. We first construct a two-state point process model incorporating spiking history and develop a likelihood ratio test to detect changes in the firing structure. We then apply adaptive state-space filters and smoothers to track these changes through time. We illustrate our approach with a simulation study as well as with experimental data recorded in the subthalamic nucleus of Parkinson's patients performing an arm movement task. Our analyses show that during the arm movement task, neurons underwent a complex pattern of modulation of spiking intensity characterized initially by a release of inhibitory control at 20-40 ms after a spike, followed by a decrease in excitatory influence at 40-60 ms after a spike.

Who are the important predators of sea turtle nests at Wreck Rock beach?

PubMed Central

Booth, David T.

2017-01-01

Excessive sea turtle nest predation is a problem for conservation management of sea turtle populations. This study assessed predation on nests of the endangered loggerhead sea turtle (Caretta caretta) at Wreck Rock beach adjacent to Deepwater National Park in Southeast Queensland, Australia after a control program for feral foxes was instigated. The presence of predators on the nesting dune was evaluated by tracking plots (2 × 1 m) every 100 m along the dune front. There were 21 (2014–2015) and 41 (2015–2016) plots established along the dune, and these were monitored for predator tracks daily over three consecutive months in both nesting seasons. Predator activities at nests were also recorded by the presence of tracks on top of nests until hatchlings emerged. In addition, camera traps were set to record the predator activity around selected nests. The tracks of the fox (Vulpes vulpes) and goanna (Varanus spp) were found on tracking plots. Tracking plots, nest tracks and camera traps indicated goanna abundance varied strongly between years. Goannas were widely distributed along the beach and had a Passive Activity Index (PAI) (0.31 in 2014–2015 and 0.16 in 2015–2016) approximately seven times higher than that of foxes (PAI 0.04 in 2014–2015 and 0.02 in 2015–2016). Five hundred and twenty goanna nest visitation events were recorded by tracks but no fox tracks were found at turtle nests. Camera trap data indicated that yellow-spotted goannas (Varanus panoptes) appeared at loggerhead turtle nests more frequently than lace monitors (V. varius) did, and further that lace monitors only predated nests previously opened by yellow-spotted goannas. No foxes were recorded at nests with camera traps. This study suggests that large male yellow-spotted goannas are the major predator of sea turtle nests at the Wreck Rock beach nesting aggregation and that goanna activity varies between years. PMID:28674666

Conducting ion tracks generated by charge-selected swift heavy ions

NASA Astrophysics Data System (ADS)

Gupta, Srashti; Gehrke, H. G.; Krauser, J.; Trautmann, C.; Severin, D.; Bender, M.; Rothard, H.; Hofsäss, H.

2016-08-01

Conducting ion tracks in tetrahedral amorphous carbon (ta-C) thin films were generated by irradiation with swift heavy ions of well-defined charge state. The conductivity of tracks and the surface topography of the films, showing characteristic hillocks at each track position, were investigated using conductive atomic force microscopy measurements. The dependence of track conductivity and hillock size on the charge state of the ions was studied using 4.6 MeV/u Pb ions of charge state 53+, 56+ and 60+ provided by GANIL, as well as 4.8 MeV/u Bi and Au ions of charge state from 50+ to 61+ and 4.2 MeV/u 238U ions in equilibrium charge state provided by UNILAC of GSI. For the charge state selection at GSI, an additional stripper-foil system was installed at the M-branch that now allows routine irradiations with ions of selected charge states. The conductivity of tracks in ta-C increases significantly when the charge state increases from 51+ to 60+. However, the conductivity of individual tracks on the same sample still shows large variations, indicating that tracks formed in ta-C are either inhomogeneous or the conductivity is limited by the interface between ion track and Si substrate.

Multiscale rescaled range analysis of EEG recordings in sevoflurane anesthesia.

PubMed

Liang, Zhenhu; Li, Duan; Ouyang, Gaoxiang; Wang, Yinghua; Voss, Logan J; Sleigh, Jamie W; Li, Xiaoli

2012-04-01

The Hurst exponent (HE) is a nonlinear method measuring the smoothness of a fractal time series. In this study we applied the HE index, extracted from electroencephalographic (EEG) recordings, as a measure of anesthetic drug effects on brain activity. In 19 adult patients undergoing sevoflurane general anesthesia, we calculated the HE of the raw EEG; comparing the maximal overlap discrete wavelet transform (MODWT) with the traditional rescaled range (R/S) analysis techniques, and with a commercial index of depth of anesthesia - the response entropy (RE). We analyzed each wavelet-decomposed sub-band as well as the combined low frequency bands (HEOLFBs). The methods were compared in regard to pharmacokinetic/pharmacodynamic (PK/PD) modeling, and prediction probability. All the low frequency band HE indices decreased when anesthesia deepened. However the HEOLFB was the best index because: it was less sensitive to artifacts, most closely tracked the exact point of loss of consciousness, showed a better prediction probability in separating the awake and unconscious states, and tracked sevoflurane concentration better - as estimated by the PK/PD models. The HE is a useful measure for estimating the depth of anesthesia. It was noted that HEOLFB showed the best performance for tracking drug effect. The HEOLFB could be used as an index for accurately estimating the effect of anesthesia on brain activity. Copyright © 2011 International Federation of Clinical Neurophysiology. All rights reserved.

The United States Air Force Small Business Innovation Research Program

DTIC Science & Technology

1990-01-01

impossible to draw, and very - satellite’s mass consists of the exists in the metal iridium , which difficult to machine. They also 0 propellant...needed for orbit is ductile and pore free. Iridium tend to be expensive, so that insertion and altitude control, bonds to, but does not react with, cutting...thin layers lifespan is 2400F and 10 hours coatings of iridium , but this track of exotic materials with precisely respectively, record was reversed in

Bar codes and intrinsic-surface-roughness tag: Accurate and low-cost accountability for CFE. [Conventional force equipment (CFE)

DOE Office of Scientific and Technical Information (OSTI.GOV)

DeVolpi, A.; Palm, R.

CFE poses a number of verification challenges that could be met in part by an accurate and low-cost means of aiding in accountability of treaty-limited equipment. Although the treaty as signed does not explicitly call for the use of tags, there is a provision for recording serial numbers'' and placing special marks'' on equipment subject to reduction. There are approximately 150,000 residual items to be tracked for CFE-I, about half for each alliance of state parties. These highly mobile items are subject to complex treaty limitations: deployment limits and zones, ceilings subceilings, holdings and allowances. There are controls and requirementsmore » for storage, conversion, and reduction. In addition, there are national security concerns regarding modernization and mobilization capability. As written into the treaty, a heavy reliance has been placed on human inspectors for CFE verification. Inspectors will mostly make visual observations and photographs as the means of monitoring compliance; these observations can be recorded by handwriting or keyed into a laptop computer. CFE is now less a treaty between two alliances than a treaty among 22 state parties, with inspection data an reports to be shared with each party in the official languages designated by CSCE. One of the potential roles for bar-coded tags would be to provide a universal, exchangable, computer-compatible language for tracking TLE. 10 figs.« less

40 CFR 240.211 - Records.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 24 2010-07-01 2010-07-01 false Records. 240.211 Section 240.211 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES GUIDELINES FOR THE THERMAL PROCESSING OF SOLID WASTES Requirements and Recommended Procedures § 240.211 Records. ...

40 CFR 240.211 - Records.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 25 2011-07-01 2011-07-01 false Records. 240.211 Section 240.211 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES GUIDELINES FOR THE THERMAL PROCESSING OF SOLID WASTES Requirements and Recommended Procedures § 240.211 Records. ...

40 CFR 240.211 - Records.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 26 2012-07-01 2011-07-01 true Records. 240.211 Section 240.211 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES GUIDELINES FOR THE THERMAL PROCESSING OF SOLID WASTES Requirements and Recommended Procedures § 240.211 Records. ...

40 CFR 240.211 - Records.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 25 2014-07-01 2014-07-01 false Records. 240.211 Section 240.211 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES GUIDELINES FOR THE THERMAL PROCESSING OF SOLID WASTES Requirements and Recommended Procedures § 240.211 Records. ...

Development of a multitarget tracking system for paramecia

NASA Astrophysics Data System (ADS)

Yeh, Yu-Sing; Huang, Ke-Nung; Jen, Sun-Lon; Li, Yan-Chay; Young, Ming-Shing

2010-07-01

This investigation develops a multitarget tracking system for the motile protozoa, paramecium. The system can recognize, track, and record the orbit of swimming paramecia within a 4 mm diameter of a circular experimental pool. The proposed system is implemented using an optical microscope, a charge-coupled device camera, and a software tool, Laboratory Virtual Instrumentation Engineering Workbench (LABVIEW). An algorithm for processing the images and analyzing the traces of the paramecia is developed in LABVIEW. It focuses on extracting meaningful data in an experiment and recording them to elucidate the behavior of paramecia. The algorithm can also continue to track paramecia even if they are transposed or collide with each other. The experiment demonstrates that this multitarget tracking design can really track more than five paramecia and simultaneously yield meaningful data from the moving paramecia at a maximum speed of 1.7 mm/s.

KENNEDY SPACE CENTER, FLA. - An engine pulls the container enclosing a segment of a solid rocket booster from the Rotation Processing and Surge Facility. The container will join others on the main track for a trip to Utah where the segments will undergo firing. The segments were part of the STS-114 stack. It is the first time actual flight segments that had been stacked for flight in the VAB are being returned for testing. They will undergo firing, which will enable inspectors to check the viability of the solid and verify the life expectancy for stacked segments.

NASA Image and Video Library

2004-01-30

KENNEDY SPACE CENTER, FLA. - An engine pulls the container enclosing a segment of a solid rocket booster from the Rotation Processing and Surge Facility. The container will join others on the main track for a trip to Utah where the segments will undergo firing. The segments were part of the STS-114 stack. It is the first time actual flight segments that had been stacked for flight in the VAB are being returned for testing. They will undergo firing, which will enable inspectors to check the viability of the solid and verify the life expectancy for stacked segments.

Advanced Diagnostic System on Earth Observing One

NASA Technical Reports Server (NTRS)

Hayden, Sandra C.; Sweet, Adam J.; Christa, Scott E.; Tran, Daniel; Shulman, Seth

2004-01-01

In this infusion experiment, the Livingstone 2 (L2) model-based diagnosis engine, developed by the Computational Sciences division at NASA Ames Research Center, has been uploaded to the Earth Observing One (EO-1) satellite. L2 is integrated with the Autonomous Sciencecraft Experiment (ASE) which provides an on-board planning capability and a software bridge to the spacecraft's 1773 data bus. Using a model of the spacecraft subsystems, L2 predicts nominal state transitions initiated by control commands, monitors the spacecraft sensors, and, in the case of failure, isolates the fault based on the discrepant observations. Fault detection and isolation is done by determining a set of component modes, including most likely failures, which satisfy the current observations. All mode transitions and diagnoses are telemetered to the ground for analysis. The initial L2 model is scoped to EO-1's imaging instruments and solid state recorder. Diagnostic scenarios for EO-1's nominal imaging timeline are demonstrated by injecting simulated faults on-board the spacecraft. The solid state recorder stores the science images and also hosts: the experiment software. The main objective of the experiment is to mature the L2 technology to Technology Readiness Level (TRL) 7. Experiment results are presented, as well as a discussion of the challenging technical issues encountered. Future extensions may explore coordination with the planner, and model-based ground operations.

Citizen scientists analyzing tropical cyclone intensities

NASA Astrophysics Data System (ADS)

Hennon, Christopher C.

2012-10-01

A new crowd sourcing project called CycloneCenter enables the public to analyze historical global tropical cyclone (TC) intensities. The primary goal of CycloneCenter, which launched in mid-September, is to resolve discrepancies in the recent global TC record arising principally from inconsistent development of tropical cyclone intensity data. The historical TC record is composed of data sets called "best tracks," which contain a forecast agency's best assessment of TC tracks and intensities. Best track data have improved in quality since the beginning of the geostationary satellite era in the 1960s (because TCs could no longer disappear from sight). However, a global compilation of best track data (International Best Track Archive for Climate Stewardship (IBTrACS)) has brought to light large interagency differences between some TC best track intensities, even in the recent past [Knapp et al., 2010Knapp et al., 2010]. For example, maximum wind speed estimates for Tropical Cyclone Gay (1989) differed by as much as 70 knots as it was tracked by three different agencies.

Big Data Provenance: Challenges, State of the Art and Opportunities

PubMed Central

Wang, Jianwu; Crawl, Daniel; Purawat, Shweta; Nguyen, Mai; Altintas, Ilkay

2017-01-01

Ability to track provenance is a key feature of scientific workflows to support data lineage and reproducibility. The challenges that are introduced by the volume, variety and velocity of Big Data, also pose related challenges for provenance and quality of Big Data, defined as veracity. The increasing size and variety of distributed Big Data provenance information bring new technical challenges and opportunities throughout the provenance lifecycle including recording, querying, sharing and utilization. This paper discusses the challenges and opportunities of Big Data provenance related to the veracity of the datasets themselves and the provenance of the analytical processes that analyze these datasets. It also explains our current efforts towards tracking and utilizing Big Data provenance using workflows as a programming model to analyze Big Data. PMID:29399671

Poster — Thur Eve — 23: Dose and Position Quality Assurance using the RADPOS System for 4D Radiotherapy with CyberKnife

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marants, R; Vandervoort, E; Cygler, J E

2014-08-15

Introduction: RADPOS 4D dosimetry system consists of a microMOSFET dosimeter combined with an electromagnetic positioning sensor, which allows for performing real-time dose and position measurements simultaneously. In this report the use of RADPOS as an independent quality assurance (QA) tool during CyberKnife 4D radiotherapy treatment is described. In addition to RADPOS, GAFCHROMIC® films were used for simultaneous dose measurement. Methods: RADPOS and films were calibrated in a Solid Water® phantom at 1.5 cm depth, SAD= 80 cm, using 60 mm cone. CT based treatment plan was created for a Solid Water® breast phantom containing metal fiducials and RADPOS probe. Dosemore » calculations were performed using iPlan pencil beam algorithm. Before the treatment delivery, GAFCHROMIC® film was inserted inside the breast phantom, next to the RADPOS probe. Then the phantom was positioned on the chest platform of the QUASAR, to which Synchrony LED optical markers were also attached. Position logging began for RADPOS and the Synchrony tracking system, the QUASAR motion was initiated and the treatment was delivered. Results: RADPOS position measurements very closely matched the LED marker positions recorded by the Synchrony camera tracking system. The RADPOS measured dose was 2.5% higher than the average film measured dose, which is within the experimental uncertainties. Treatment plan calculated dose was 4.1 and 1.6% lower than measured by RADPOS and film, respectively. This is most likely due to the inferior nature of the dose calculation algorithm. Conclusions: Our study demonstrates that RADPOS system is a useful tool for independent QA of CyberKnife treatments.« less

Accurately tracking single-cell movement trajectories in microfluidic cell sorting devices.

PubMed

Jeong, Jenny; Frohberg, Nicholas J; Zhou, Enlu; Sulchek, Todd; Qiu, Peng

2018-01-01

Microfluidics are routinely used to study cellular properties, including the efficient quantification of single-cell biomechanics and label-free cell sorting based on the biomechanical properties, such as elasticity, viscosity, stiffness, and adhesion. Both quantification and sorting applications require optimal design of the microfluidic devices and mathematical modeling of the interactions between cells, fluid, and the channel of the device. As a first step toward building such a mathematical model, we collected video recordings of cells moving through a ridged microfluidic channel designed to compress and redirect cells according to cell biomechanics. We developed an efficient algorithm that automatically and accurately tracked the cell trajectories in the recordings. We tested the algorithm on recordings of cells with different stiffness, and showed the correlation between cell stiffness and the tracked trajectories. Moreover, the tracking algorithm successfully picked up subtle differences of cell motion when passing through consecutive ridges. The algorithm for accurately tracking cell trajectories paves the way for future efforts of modeling the flow, forces, and dynamics of cell properties in microfluidics applications.

Characterization of Heterogeneity in Childhood Immunization Coverage in Central Florida Using Immunization Registry Data.

PubMed

Thompson, Kimberly M; Logan, Grace E

2016-07-01

Despite high vaccine coverage in the United States in general, and in the State of Florida specifically, some children miss scheduled vaccines due to health system failures or vaccine refusal by their parents. Recent experiences with outbreaks in the United States suggest that geographic clustering of un(der)vaccinated populations represent a threat to the elimination status of some vaccine-preventable diseases. Immunization registries continue to expand and play an important role in efforts to track vaccine coverage and use. Using nearly 700,000 de-identified immunization records from the Florida Department of Health immunization information system (Florida SHOTS™) for children born during 2003-2014, we explored heterogeneity and potential clustering of un(der)vaccinated children in six counties in central Florida-Brevard, Lake, Orange, Oseola, Polk, and Seminole-that represent a high-risk area for importation due to family tourist attractions in the area. By zip code, we mapped the population density, the percent of children with religious exemptions, the percent of children on track or overdue for each vaccine series without and with exemptions, and the numbers of children with no recorded dose of each vaccine. Overall, we found some heterogeneity in coverage among the counties and zip codes, but relatively consistent and high coverage. We found that some children with an exemption in the system received the vaccines we analyzed, but exemption represents a clear risk factor for un(der)immunization. We identified many challenges associated with using immunization registry data for spatial analysis and potential opportunities to improve registries to better support future analyses. © 2015 Society for Risk Analysis.

A novel class of halogen-free, super-conductive lithium argyrodites: Synthesis and characterization

NASA Astrophysics Data System (ADS)

Schneider, Holger; Du, Hui; Kelley, Tracy; Leitner, Klaus; ter Maat, Johan; Scordilis-Kelley, Chariclea; Sanchez-Carrera, Roel; Kovalev, Igor; Mudalige, Anoma; Kulisch, Jörn; Safont-Sempere, Marina M.; Hartmann, Pascal; Weiβ, Thomas; Schneider, Ling; Hinrichsen, Bernd

2017-10-01

Solid electrolytes are the core components for many next generation lithium battery concepts such as all-solid-state batteries (ASSB) or batteries based on metallic lithium anodes protected by a ceramic or composite passivation layer. Therefore, the search for new solid state Li-ion conductors with superior properties and improved electrochemical stabilities remains of high interest. In this work, the synthesis of a new class of silicon-containing, sulfide-based lithium-ion conductors is reported. Very good conductivities of up to ∼2.0-3.0·10-3 S/cm could be achieved for compositions such as Li22SiP2S18, among the highest for silicon sulfide containing materials. Based on the recorded powder XRD diffraction patterns and simulations it could be confirmed that they constitute novel members of the argyrodite family of sulfide lithium-ion conductors. The cubic high-temperature modification of such argyrodites with high lithium-ion conductivity can therefore be stabilized by implementation of silicon into the lattice, while additional doping with halogen atoms is not necessary.

Formation of sodium bismuth titanate-barium titanate during solid-state synthesis

DOE PAGES

Hou, Dong; Aksel, Elena; Fancher, Chris M.; ...

2017-01-12

Phase formation of sodium bismuth titanate (Na 0.5Bi 0.5TiO 3 or NBT) and its solid solution with barium titanate (BaTiO 3 or BT) during the calcination process is studied using in situ high-temperature diffraction. The reactant powders were mixed and heated to 1000°C, while X-ray diffraction patterns were recorded continuously. Phase evolutions from starting materials to final perovskite products are observed, and different transient phases are identified. The formation mechanism of NBT and NBT–xBT perovskite structures is discussed, and a reaction sequence is suggested based on the observations. The in situ study leads to a new processing approach, which ismore » the use of nano-TiO 2, and gives insights to the particle size effect for solid-state synthesis products. Lastly, it was found that the use of nano-TiO 2 as reactant powder accelerates the synthesis process, decreases the formation of transient phases, and helps to obtain phase-pure products using a lower thermal budget.« less

A Micromagnetic Study of Medium Orientation Ratio Effects in High Areal Density Recording

NASA Astrophysics Data System (ADS)

Plumer, Martin; van Ek, Johannes

2000-03-01

An extensive analysis of written tracks on granular media with anisotropy axes preferentially oriented either in the down-track or cross-track direction was performed with a newly developed micromagnetic model of magnetic recording [1]. The response of planar media to writer head fields, derived from the Finite-Element-Method, is calculated by solving the LLG equations. Signal from the written transitions is determined through a micromagnetic model of a GMR spin-valve device. Using fields from a generic 10Gb/in2 head (TPWG=0.6um, gap=0.2um, 1.8T materials around the gap), dibits were written at high linear density. Relative to the isotropic case, both erase bands and read-back voltage deteriorate for cross-track oriented media and improve in the down-track orientation case. For an orientation ratio of 1.23, the read-back signal at 200 kbpi drops by 15% in the radial case and increases by 15% in the circumferential case. Although the cross-track coercivity is smaller for down-track oriented media, and thus easier to write with the corners of the head, the remnant cross-track magnetization is correspondingly smaller. Track edge distortion is thus less severe than for isotropic media. Oriented media is of interest due to enhanced thermal stability and faster switching times [2]. [1] J. van Ek, M.L. Plumer, H. Zhou and H.N. Bertram, ``A Micromagnetic Recording Model for Write and Read-back," in preparation. Also see the GMAG symposium, this conference. [2] E.N. Abarra, I. Okamoto and M. Shinohara, IEEE Trans. Mag. 35, 2709 (1999).

Single- and multi-frequency detection of surface displacements via scanning probe microscopy.

PubMed

Romanyuk, Konstantin; Luchkin, Sergey Yu; Ivanov, Maxim; Kalinin, Arseny; Kholkin, Andrei L

2015-02-01

Piezoresponse force microscopy (PFM) provides a novel opportunity to detect picometer-level displacements induced by an electric field applied through a conducting tip of an atomic force microscope (AFM). Recently, it was discovered that superb vertical sensitivity provided by PFM is high enough to monitor electric-field-induced ionic displacements in solids, the technique being referred to as electrochemical strain microscopy (ESM). ESM has been implemented only in multi-frequency detection modes such as dual AC resonance tracking (DART) and band excitation, where the response is recorded within a finite frequency range, typically around the first contact resonance. In this paper, we analyze and compare signal-to-noise ratios of the conventional single-frequency method with multi-frequency regimes of measuring surface displacements. Single-frequency detection ESM is demonstrated using a commercial AFM.

Characterization of fast deuterons involved in the production of fusion neutrons in a dense plasma focus

NASA Astrophysics Data System (ADS)

Kubes, P.; Paduch, M.; Sadowski, M. J.; Cikhardt, J.; Cikhardtova, B.; Klir, D.; Kravarik, J.; Munzar, V.; Rezac, K.; Zielinska, E.; Skladnik-Sadowska, E.; Szymaszek, A.; Tomaszewski, K.; Zaloga, D.

2018-01-01

This paper considers regions of a fast deuteron production in a correlation with an evolution of ordered structures inside a pinch column of a mega-ampere plasma focus discharge. Ion pinhole cameras equipped with plastic PM-355 track-detectors recorded fast deuterons escaping in the downstream and other directions (up to 60° to the z-axis). Time-integrated ion images made it possible to estimate sources of the deuteron acceleration at the known magnetic field and deuteron energy values. The images of the fast deuterons emitted in the solid angle ranging from 0° to 4° showed two forms: central spots and circular images. The spots of 1-2 cm in diameter were produced by deuterons from the central pinch regions. The circular-shaped images of a radius above 3 cm (or their parts) were formed by deuterons from the region surrounding the dense pinch column. The ion pinhole cameras placed at angles above 20° to the z-axis recorded the ion spots only, and the ring-images were missing. The central region of the deuteron acceleration could be associated mainly with plasmoids, and the circular images could be connected with ring-shaped regions of the radius corresponding to tops of the plasma lobules outside the dense pinch column. The deuteron tracks forming ring-shaped images of a smaller (0.5-1) cm radius could be produced by deflections of the fast deuterons, which were caused by a magnetic field inside the dense pinch column.

Real-Time Radar-Based Tracking and State Estimation of Multiple Non-Conformant Aircraft

NASA Technical Reports Server (NTRS)

Cook, Brandon; Arnett, Timothy; Macmann, Owen; Kumar, Manish

2017-01-01

In this study, a novel solution for automated tracking of multiple unknown aircraft is proposed. Many current methods use transponders to self-report state information and augment track identification. While conformant aircraft typically report transponder information to alert surrounding aircraft of its state, vehicles may exist in the airspace that are non-compliant and need to be accurately tracked using alternative methods. In this study, a multi-agent tracking solution is presented that solely utilizes primary surveillance radar data to estimate aircraft state information. Main research challenges include state estimation, track management, data association, and establishing persistent track validity. In an effort to realize these challenges, techniques such as Maximum a Posteriori estimation, Kalman filtering, degree of membership data association, and Nearest Neighbor Spanning Tree clustering are implemented for this application.

Track lateral shift : fundamentals and state-of-the-art review

DOT National Transportation Integrated Search

1996-02-01

This report presents a review of the state of the art of track lateral shift analysis, with improved concepts for safety evaluation of high speed trains generating track shift forces. The mechanics of track shift and the resulting track failure modes...

Didactyl Tracks of Paravian Theropods (Maniraptora) from the ?Middle Jurassic of Africa

PubMed Central

Mudroch, Alexander; Richter, Ute; Joger, Ulrich; Kosma, Ralf; Idé, Oumarou; Maga, Abdoulaye

2011-01-01

Background A new dinosaur tracksite from ?Middle Jurassic sediments of the Irhazer Group on the plains of Agadez (Rep. Niger, northwest Africa) revealed extraordinarily well preserved didactyl tracks of a digitigrade bipedal trackmaker. The distinct morphology of the pes imprints indicates a theropod trackmaker from a paravian maniraptoran closely related to birds. Methodology/Principal Findings The early age and the morphological traits of the tracks allow for description of the new ichnotaxon Paravipus didactyloides. A total of 120 tracks are assigned to 5 individual trackways. The ‘medium-sized’ tracks with an average footprint length of 27.5 cm and footprint width of 23.1 cm are deeply imprinted into the track bearing sandstone. Conclusions/Significance A comparison with other didactyl tracks gives new insights into the foot morphology of advanced maniraptoran theropods and contributes to knowledge of their evolutionary history. The new ichnotaxon takes an important position in the ichnological fossil record of Gondwana and the mid-Jurassic biota worldwide, because it is among the earliest known records of paravian maniraptorans and of didactyl theropod tracks from Africa. PMID:21339816

UltraTrack: Software for semi-automated tracking of muscle fascicles in sequences of B-mode ultrasound images.

PubMed

Farris, Dominic James; Lichtwark, Glen A

2016-05-01

Dynamic measurements of human muscle fascicle length from sequences of B-mode ultrasound images have become increasingly prevalent in biomedical research. Manual digitisation of these images is time consuming and algorithms for automating the process have been developed. Here we present a freely available software implementation of a previously validated algorithm for semi-automated tracking of muscle fascicle length in dynamic ultrasound image recordings, "UltraTrack". UltraTrack implements an affine extension to an optic flow algorithm to track movement of the muscle fascicle end-points throughout dynamically recorded sequences of images. The underlying algorithm has been previously described and its reliability tested, but here we present the software implementation with features for: tracking multiple fascicles in multiple muscles simultaneously; correcting temporal drift in measurements; manually adjusting tracking results; saving and re-loading of tracking results and loading a range of file formats. Two example runs of the software are presented detailing the tracking of fascicles from several lower limb muscles during a squatting and walking activity. We have presented a software implementation of a validated fascicle-tracking algorithm and made the source code and standalone versions freely available for download. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Burst suppression probability algorithms: state-space methods for tracking EEG burst suppression

NASA Astrophysics Data System (ADS)

Chemali, Jessica; Ching, ShiNung; Purdon, Patrick L.; Solt, Ken; Brown, Emery N.

2013-10-01

Objective. Burst suppression is an electroencephalogram pattern in which bursts of electrical activity alternate with an isoelectric state. This pattern is commonly seen in states of severely reduced brain activity such as profound general anesthesia, anoxic brain injuries, hypothermia and certain developmental disorders. Devising accurate, reliable ways to quantify burst suppression is an important clinical and research problem. Although thresholding and segmentation algorithms readily identify burst suppression periods, analysis algorithms require long intervals of data to characterize burst suppression at a given time and provide no framework for statistical inference. Approach. We introduce the concept of the burst suppression probability (BSP) to define the brain's instantaneous propensity of being in the suppressed state. To conduct dynamic analyses of burst suppression we propose a state-space model in which the observation process is a binomial model and the state equation is a Gaussian random walk. We estimate the model using an approximate expectation maximization algorithm and illustrate its application in the analysis of rodent burst suppression recordings under general anesthesia and a patient during induction of controlled hypothermia. Main result. The BSP algorithms track burst suppression on a second-to-second time scale, and make possible formal statistical comparisons of burst suppression at different times. Significance. The state-space approach suggests a principled and informative way to analyze burst suppression that can be used to monitor, and eventually to control, the brain states of patients in the operating room and in the intensive care unit.

Experimental evaluation of the response of micro-channel plate detector to ions with 10s of MeV energies.

PubMed

Jeong, Tae Won; Singh, P K; Scullion, C; Ahmed, H; Kakolee, K F; Hadjisolomou, P; Alejo, A; Kar, S; Borghesi, M; Ter-Avetisyan, S

2016-08-01

The absolute calibration of a microchannel plate (MCP) assembly using a Thomson spectrometer for laser-driven ion beams is described. In order to obtain the response of the whole detection system to the particles' impact, a slotted solid state nuclear track detector (CR-39) was installed in front of the MCP to record the ions simultaneously on both detectors. The response of the MCP (counts/particles) was measured for 5-58 MeV carbon ions and for protons in the energy range 2-17.3 MeV. The response of the MCP detector is non-trivial when the stopping range of particles becomes larger than the thickness of the detector. Protons with energies E ≳ 10 MeV are energetic enough that they can pass through the MCP detector. Quantitative analysis of the pits formed in CR-39 and the signal generated in the MCP allowed to determine the MCP response to particles in this energy range. Moreover, a theoretical model allows to predict the response of MCP at even higher proton energies. This suggests that in this regime the MCP response is a slowly decreasing function of energy, consistently with the decrease of the deposited energy. These calibration data will enable particle spectra to be obtained in absolute terms over a broad energy range.

Experimental evaluation of the response of micro-channel plate detector to ions with 10s of MeV energies

NASA Astrophysics Data System (ADS)

Jeong, Tae Won; Singh, P. K.; Scullion, C.; Ahmed, H.; Kakolee, K. F.; Hadjisolomou, P.; Alejo, A.; Kar, S.; Borghesi, M.; Ter-Avetisyan, S.

2016-08-01

The absolute calibration of a microchannel plate (MCP) assembly using a Thomson spectrometer for laser-driven ion beams is described. In order to obtain the response of the whole detection system to the particles' impact, a slotted solid state nuclear track detector (CR-39) was installed in front of the MCP to record the ions simultaneously on both detectors. The response of the MCP (counts/particles) was measured for 5-58 MeV carbon ions and for protons in the energy range 2-17.3 MeV. The response of the MCP detector is non-trivial when the stopping range of particles becomes larger than the thickness of the detector. Protons with energies E ≳ 10 MeV are energetic enough that they can pass through the MCP detector. Quantitative analysis of the pits formed in CR-39 and the signal generated in the MCP allowed to determine the MCP response to particles in this energy range. Moreover, a theoretical model allows to predict the response of MCP at even higher proton energies. This suggests that in this regime the MCP response is a slowly decreasing function of energy, consistently with the decrease of the deposited energy. These calibration data will enable particle spectra to be obtained in absolute terms over a broad energy range.

Video redaction: a survey and comparison of enabling technologies

NASA Astrophysics Data System (ADS)

Sah, Shagan; Shringi, Ameya; Ptucha, Raymond; Burry, Aaron; Loce, Robert

2017-09-01

With the prevalence of video recordings from smart phones, dash cams, body cams, and conventional surveillance cameras, privacy protection has become a major concern, especially in light of legislation such as the Freedom of Information Act. Video redaction is used to obfuscate sensitive and personally identifiable information. Today's typical workflow involves simple detection, tracking, and manual intervention. Automated methods rely on accurate detection mechanisms being paired with robust tracking methods across the video sequence to ensure the redaction of all sensitive information while minimizing spurious obfuscations. Recent studies have explored the use of convolution neural networks and recurrent neural networks for object detection and tracking. The present paper reviews the redaction problem and compares a few state-of-the-art detection, tracking, and obfuscation methods as they relate to redaction. The comparison introduces an evaluation metric that is specific to video redaction performance. The metric can be evaluated in a manner that allows balancing the penalty for false negatives and false positives according to the needs of particular application, thereby assisting in the selection of component methods and their associated hyperparameters such that the redacted video has fewer frames that require manual review.

The pneumatic syringe: a simple apparatus for self-administration of drugs by rats.

PubMed

Weeks, J R

1977-12-01

Drug solution is delivered by a syringe operated by a pneumatic cylinder. Recommended delivery volumes are from 10 to 200 microliter. A solid-state control unit is described which can operate two syringes (drug injection and flush), has outputs for recording responses and injections, and can be programmed to provide several schedules of reinforcement. All components are readily commercially available.

Head-disk interface nanotribology for Tbit/inch2 recording densities: near-contact and contact recording

NASA Astrophysics Data System (ADS)

Vakis, Antonis I.; Polycarpou, Andreas A.

2010-06-01

In the effort to achieve Tbit/inch2 recording densities, thermal fly-height control (TFC) nanotechnology was developed to effectively reduce the clearance (which is of the order of a few nanometres) at the head-disk interface (HDI) of hard-disk drives. In this work, we present a model of the HDI that can predict the dynamic flying and nanotribological contacting behaviour, allowing for accurate predictions and characterization of the operating regime as a function of TFC actuation. A geometric model for TFC is presented and an improved definition of contact at the interface is developed in the presence of nanoscale topographical roughness and dynamic microwaviness. A new methodology is proposed for the calculation of the nominal area of contact, which affects both near- and at-contact behaviour, while the stiffening of the air bearing force with TFC actuation is also accounted for. Slider behaviour is analysed by quantifying the approach, jump-to-contact, lubricant and solid contact regimes of operation and identifying the critical and optimum TFC actuations. The feasibility of near-contact, light molecularly thin lubricant contact versus solid contact recording is explored under the effect of the interfacial forces and stresses present at the HDI. The clearance and the state of vibrations are analysed and design guidelines are proposed for improved performance.

A portable multi-channel recording system for analysis of acceleration and angular velocity in six dimension.

PubMed

Yamashita, M; Yamashita, A; Ishii, T; Naruo, Y; Nagatomo, M

1998-11-01

A portable recording system was developed for analysis of more than three analog signals collected in field works. Stereo audio recorder, available as consumer products, was made use for a core cornponent of the system. For the two tracks of recording, a multiplexed analog signal is stored on one track, and reference code on the other track. The reference code indicates the start of one cycle for multiplexing and swiching point of each channel. Multiplexed signal is playbacked and decoded with a reference of the code to reconstruct original profiles of the signal. Since commercial stereo recorders have cut DC component off, a fixed reference voltage is inserted in the sequence of multiplexing. Change of voltage at switching from the reference to the data channel is measured from playbacked signal to get the original data with its DC component. Movement of vehicles and human head were analyzed by the system. It was verified to be capable to record and analyze multi-channel signal at a sampling rate more than 10Hz.

Advanced 2-micron Solid-state Laser for Wind and CO2 Lidar Applications

NASA Technical Reports Server (NTRS)

Yu, Jirong; Trieu, Bo C.; Petros, Mulugeta; Bai, Yingxin; Petzar, Paul J.; Koch, Grady J.; Singh, Upendra N.; Kavaya, Michael J.

2006-01-01

Significant advancements in the 2-micron laser development have been made recently. Solid-state 2-micron laser is a key subsystem for a coherent Doppler lidar that measures the horizontal and vertical wind velocities with high precision and resolution. The same laser, after a few modifications, can also be used in a Differential Absorption Lidar (DIAL) system for measuring atmospheric CO2 concentration profiles. The world record 2-micron laser energy is demonstrated with an oscillator and two amplifiers system. It generates more than one joule per pulse energy with excellent beam quality. Based on the successful demonstration of a fully conductive cooled oscillator by using heat pipe technology, an improved fully conductively cooled 2-micron amplifier was designed, manufactured and integrated. It virtually eliminates the running coolant to increase the overall system efficiency and reliability. In addition to technology development and demonstration, a compact and engineering hardened 2-micron laser is under development. It is capable of producing 250 mJ at 10 Hz by an oscillator and one amplifier. This compact laser is expected to be integrated to a lidar system and take field measurements. The recent achievements push forward the readiness of such a laser system for space lidar applications. This paper will review the developments of the state-of-the-art solid-state 2-micron laser.

The Nimbus 4 data catalog. Volume 4: Data orbits 1957-2775 and Interrogation, Recording and Location System (IRLS) balloon tracking experiment data from launch through 27 March 1971, 1 September - 31 October 1970

NASA Technical Reports Server (NTRS)

1971-01-01

Nimbus 4 satellite data for the period September 1 through October 31 1970 are presented. Data are also given on interrogation recording and location system balloon tracking from launch through March 27, 1971.

Establishing a 'track record': research productivity and nursing academe.

PubMed

Emden, C

1998-01-01

Many nursing academics in Australia are finding to their dismay that an outstanding teaching career and exemplary professional contribution to their field--and a PhD--are not enough to achieve promotion within their university, or secure a new academic post. One must also possess a proven or established 'track record' in research and publication. The operational funding arrangements for Australian universities rely in part on the research productivity of their academic staff members. This places special expectation upon the way academics conduct their scholarly work. Nursing academics are under particular pressure: as relative newcomers to the university scene, most find themselves considered as early career researchers with weak track records. This paper reviews relevant research and draws upon personal experience in the area of research development, to highlight how nursing academics may most strategically establish a research and publication record with a view to career advancement.

A large-aperture low-cost hydrophone array for tracking whales from small boats.

PubMed

Miller, B; Dawson, S

2009-11-01

A passive sonar array designed for tracking diving sperm whales in three dimensions from a single small vessel is presented, and the advantages and limitations of operating this array from a 6 m boat are described. The system consists of four free floating buoys, each with a hydrophone, built-in recorder, and global positioning system receiver (GPS), and one vertical stereo hydrophone array deployed from the boat. Array recordings are post-processed onshore to obtain diving profiles of vocalizing sperm whales. Recordings are synchronized using a GPS timing pulse recorded onto each track. Sensitivity analysis based on hyperbolic localization methods is used to obtain probability distributions for the whale's three-dimensional location for vocalizations received by at least four hydrophones. These localizations are compared to those obtained via isodiachronic sequential bound estimation. Results from deployment of the system around a sperm whale in the Kaikoura Canyon in New Zealand are shown.

Adaptive particle filter for robust visual tracking

NASA Astrophysics Data System (ADS)

Dai, Jianghua; Yu, Shengsheng; Sun, Weiping; Chen, Xiaoping; Xiang, Jinhai

2009-10-01

Object tracking plays a key role in the field of computer vision. Particle filter has been widely used for visual tracking under nonlinear and/or non-Gaussian circumstances. In particle filter, the state transition model for predicting the next location of tracked object assumes the object motion is invariable, which cannot well approximate the varying dynamics of the motion changes. In addition, the state estimate calculated by the mean of all the weighted particles is coarse or inaccurate due to various noise disturbances. Both these two factors may degrade tracking performance greatly. In this work, an adaptive particle filter (APF) with a velocity-updating based transition model (VTM) and an adaptive state estimate approach (ASEA) is proposed to improve object tracking. In APF, the motion velocity embedded into the state transition model is updated continuously by a recursive equation, and the state estimate is obtained adaptively according to the state posterior distribution. The experiment results show that the APF can increase the tracking accuracy and efficiency in complex environments.

Tracking interface and common curve dynamics for two-fluid flow in porous media

DOE PAGES

Mcclure, James E.; Miller, Cass T.; Gray, W. G.; ...

2016-04-29

Pore-scale studies of multiphase flow in porous medium systems can be used to understand transport mechanisms and quantitatively determine closure relations that better incorporate microscale physics into macroscale models. Multiphase flow simulators constructed using the lattice Boltzmann method provide a means to conduct such studies, including both the equilibrium and dynamic aspects. Moving, storing, and analyzing the large state space presents a computational challenge when highly-resolved models are applied. We present an approach to simulate multiphase flow processes in which in-situ analysis is applied to track multiphase flow dynamics at high temporal resolution. We compute a comprehensive set of measuresmore » of the phase distributions and the system dynamics, which can be used to aid fundamental understanding and inform closure relations for macroscale models. The measures computed include microscale point representations and macroscale averages of fluid saturations, the pressure and velocity of the fluid phases, interfacial areas, interfacial curvatures, interface and common curve velocities, interfacial orientation tensors, phase velocities and the contact angle between the fluid-fluid interface and the solid surface. Test cases are studied to validate the approach and illustrate how measures of system state can be obtained and used to inform macroscopic theory.« less

Room temperature solid-state quantum emitters in the telecom range

PubMed Central

Bodrog, Zoltán; Adamo, Giorgio; Gali, Adam

2018-01-01

On-demand, single-photon emitters (SPEs) play a key role across a broad range of quantum technologies. In quantum networks and quantum key distribution protocols, where photons are used as flying qubits, telecom wavelength operation is preferred because of the reduced fiber loss. However, despite the tremendous efforts to develop various triggered SPE platforms, a robust source of triggered SPEs operating at room temperature and the telecom wavelength is still missing. We report a triggered, optically stable, room temperature solid-state SPE operating at telecom wavelengths. The emitters exhibit high photon purity (~5% multiphoton events) and a record-high brightness of ~1.5 MHz. The emission is attributed to localized defects in a gallium nitride (GaN) crystal. The high-performance SPEs embedded in a technologically mature semiconductor are promising for on-chip quantum simulators and practical quantum communication technologies. PMID:29670945

Using Solid State Disk Array as a Cache for LHC ATLAS Data Analysis

NASA Astrophysics Data System (ADS)

Yang, W.; Hanushevsky, A. B.; Mount, R. P.; Atlas Collaboration

2014-06-01

User data analysis in high energy physics presents a challenge to spinning-disk based storage systems. The analysis is data intense, yet reads are small, sparse and cover a large volume of data files. It is also unpredictable due to users' response to storage performance. We describe here a system with an array of Solid State Disk as a non-conventional, standalone file level cache in front of the spinning disk storage to help improve the performance of LHC ATLAS user analysis at SLAC. The system uses several days of data access records to make caching decisions. It can also use information from other sources such as a work-flow management system. We evaluate the performance of the system both in terms of caching and its impact on user analysis jobs. The system currently uses Xrootd technology, but the technique can be applied to any storage system.

Lif and Raman Spectroscopy in Undergraduate Labs Using Green Diode-Pumped Solid-State Lasers

NASA Astrophysics Data System (ADS)

Gray, Jeffrey A.

2015-06-01

Electronic spectroscopy of molecular iodine vapor has long been studied in undergraduate physical chemistry teaching laboratories, but the effectiveness of emission work has typically been limited by availability of instrumentation. This talk shows how to make inexpensive green diode-pumped solid-state (DPSS) lasers easily tunable for efficient, selective excitation of I2. Miniature fiber-optic spectrometers then enable rotationally resolved fluorescence spectroscopy up to v" = 42 near 900 nm with acquisition times of less than one minute. DPSS lasers are also versatile excitation sources for vibrational Raman spectroscopy, which is another common exercise that has been limited by lack of proper instrumentation in the teaching laboratory. This talk shows how to construct a simple accessory for commercial fluorimeters to record vibrational Raman spectra and depolarization ratios for CCl4 and C2Cl4 as part of a lab exercise featuring molecular symmetry.

Political impediments to a tobacco endgame

PubMed Central

Rabe, Barry George

2013-01-01

Any serious consideration of exploring a tobacco endgame in the USA must build upon the enviable track record of reducing tobacco use through a mixture of federal and state policies. This foundation may pose particular challenges in approaching an endgame, including questions of national political feasibility, public support, limitations of sub-federal experimentation and recruitment of future political champions. Advocates must demonstrate a compelling need for a dramatic expansion beyond existing efforts, amid competition from alternative issues and little apparent public appetite for such an initiative. PMID:23591512

Solar Smarter Faster

ScienceCinema

Armbrust, Dan; Haldar, Pradeep; Kaloyeros, Alain; Holladay, Dan

2018-05-11

As part of the SunShot Initiative, U.S. Department of Energy Secretary Steven Chu announced on April 15th the selection of up to $112.5 million over five years for funding to support the development of advanced solar photovoltaic (PV)-related manufacturing processes throughout the United States. The effort is led by Sematech, with a proven track record in breathing life back into the US semiconduster industry, and in partnership with CNSE, The College of Nanoscale Science and Engineering, who supplies world class R&D experts and facilities.

Searches for dark matter and new physics with unconventional signatures

NASA Astrophysics Data System (ADS)

Wulz, C.-E.; CMS Collaboration

2017-07-01

Selected results on searches for dark matter and unconventional signatures with the CMS detector are presented. Dark matter searches in channels with one or two jets, single photons, vector bosons, or top and bottom quarks combined with missing momentum in the final states are described. Unusual signatures such as displaced objects, disappearing or kinked tracks, delayed or stopped particles have also been explored. The analyses were performed with proton-proton data recorded at LHC centre-of-mass energies up to 13TeV.

Application of Ensemble Kalman Filter in Power System State Tracking and Sensitivity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Yulan; Huang, Zhenyu; Zhou, Ning

2012-05-01

Ensemble Kalman Filter (EnKF) is proposed to track dynamic states of generators. The algorithm of EnKF and its application to generator state tracking are presented in detail. The accuracy and sensitivity of the method are analyzed with respect to initial state errors, measurement noise, unknown fault locations, time steps and parameter errors. It is demonstrated through simulation studies that even with some errors in the parameters, the developed EnKF can effectively track generator dynamic states using disturbance data.

Use of a novel tunable solid state disk laser as a diagnostic system for laser-induced fluorescence

NASA Astrophysics Data System (ADS)

Paa, Wolfgang; Triebel, Wolfgang

2004-09-01

An all solid state disk laser system-named "Advanced Disk Laser (ADL)" -particularly tailored for laser induced fluorescence (LIF) in combustion processes is presented. The system currently under development comprises an Yb:YAG-seedlaser and a regenerative amplifier. Both are based on the disk laser concept as a new laser architecture. This allows a tunable, compact, efficient diode pumped solid state laser (DPSSL) system with repetition rates in the kHz region. After frequency conversion to the UV-spectral region via third and fourth harmonics generation, this laser-due to its unique properties such as single-frequency operation, wavelength tuneability and excellent beam profile-is well suited for excitation of small molecules such as formaldehyde, OH, NO or O2, which are characteristic for combustion processes. Using the method of planar laser induced fluorescence (PLIF) we observed concentration distributions of formaldehyde in cool and hot flames of a specially designed diethyl-ether burner. The images recorded with 1 kHz repetition rate allow visualizing the distribution of formaldehyde on a 1 ms time scale. This demonstrates for the first time the usability of this novel laser for LIF measurements and is the first step towards integration of the ADL into capsules for drop towers and the international space station.

LANDSAT-D data format control book. Volume 6, appendix K: Unprocessed multispectral scanner high density tape (HDT-RM/HDT-GM)

NASA Technical Reports Server (NTRS)

Andersen, K. E.

1981-01-01

Unprocessed MSS data which is recorded on HDT-RM (a 28 track, high density tape) and on HDT-GM (a 14 track, nonbias recorded, high density tape) are inputs for the LANDSAT 4 data management system. All MSS data initially recorded on HDT-GM are copied to HDT-RM prior to processing. This specification establishes the requirements for the format of the LANDSAT D HDT-RM/HDT-GM.

Speech watermarking: an approach for the forensic analysis of digital telephonic recordings.

PubMed

Faundez-Zanuy, Marcos; Lucena-Molina, Jose J; Hagmüller, Martin

2010-07-01

In this article, the authors discuss the problem of forensic authentication of digital audio recordings. Although forensic audio has been addressed in several articles, the existing approaches are focused on analog magnetic recordings, which are less prevalent because of the large amount of digital recorders available on the market (optical, solid state, hard disks, etc.). An approach based on digital signal processing that consists of spread spectrum techniques for speech watermarking is presented. This approach presents the advantage that the authentication is based on the signal itself rather than the recording format. Thus, it is valid for usual recording devices in police-controlled telephone intercepts. In addition, our proposal allows for the introduction of relevant information such as the recording date and time and all the relevant data (this is not always possible with classical systems). Our experimental results reveal that the speech watermarking procedure does not interfere in a significant way with the posterior forensic speaker identification.

Ultra heavy cosmic ray experiment (A0178)

NASA Technical Reports Server (NTRS)

Thompson, A.; Osullivan, D.; Bosch, J.; Keegan, R.; Wenzel, K. P.; Jansen, F.; Domingo, C.

1992-01-01

The Ultra Heavy Cosmic Ray Experiment (UHCRE) is based on a modular array of 192 side viewing solid state nuclear track detector stacks. These stacks were mounted in sets of four in 48 pressure vessels using 16 peripheral LDEF trays. The geometry factor for high energy cosmic ray nuclei, allowing for Earth shadowing, was 30 sq m sr, giving a total exposure factor of 170 sq m sr y at an orbital inclination of 28.4 degs. Scanning results indicate that about 3000 cosmic ray nuclei in the charge region with Z greater than 65 were collected. This sample is more than ten times the current world data in the field (taken to be the data set from the HEAO-3 mission plus that from the Ariel-6 mission) and is sufficient to provide the world's first statistically significant sample of actinide cosmic rays. Results are presented including a sample of ultra heavy cosmic ray nuclei, analysis of pre-flight and post-flight calibration events and details of track response in the context of detector temperature history. The integrated effect of all temperature and age related latent track variations cause a maximum charge shift of + or - 0.8e for uranium and + or - 0.6e for the platinum-lead group. Astrophysical implications of the UHCRE charge spectrum are discussed.

Empirical assessment of the detection efficiency of CR-39 at high proton fluence and a compact, proton detector for high-fluence applications

DOE PAGES

Rosenberg, M. J.; Séguin, F. H.; Waugh, C. J.; ...

2014-04-14

CR-39 solid-state nuclear track detectors are widely used in physics and in many inertial confinement fusion (ICF) experiments, and under ideal conditions these detectors have 100% detection efficiency for ~0.5–8 MeV protons. When the fluence of incident particles becomes too high, the overlap of particle tracks leads to under-counting at typical processing conditions (5h etch in 6N NaOH at 80°C). Short etch times required to avoid overlap can cause under-counting as well, as tracks are not fully developed. Experiments have determined the minimum etch times for 100% detection of 1.7–4.3-MeV protons and established that for 2.4-MeV protons, relevant for detectionmore » of DD protons, the maximum fluence that can be detected using normal processing techniques is ≲3 ×10 6 cm -2. A CR-39-based proton detector has been developed to mitigate issues related to high particle fluences on ICF facilities. Using a pinhole and scattering foil several mm in front of the CR-39, proton fluences at the CR-39 are reduced by more than a factor of ~50, increasing the operating yield upper limit by a comparable amount.« less

Infant Eye-Tracking in the Context of Goal-Directed Actions

ERIC Educational Resources Information Center

Corbetta, Daniela; Guan, Yu; Williams, Joshua L.

2012-01-01

This paper presents two methods that we applied to our research to record infant gaze in the context of goal-oriented actions using different eye-tracking devices: head-mounted and remote eye-tracking. For each type of eye-tracking system, we discuss their advantages and disadvantages, describe the particular experimental setups we used to study…

Emerging applications of spark plasma sintering in all solid-state lithium-ion batteries and beyond

NASA Astrophysics Data System (ADS)

Zhu, Hongzheng; Liu, Jian

2018-07-01

Solid-state batteries have received increasing attention due to their high safety aspect and high energy and power densities. However, the development of solid-state batteries is hindered by inferior solid-solid interfaces between the solid-state electrolyte and electrode, which cause high interfacial resistance, reduced Li-ion and electron transfer rate, and limited battery performance. Recently, spark plasma sintering (SPS) is emerging as a promising technique for fabricating solid-state electrolyte and electrode pellets with clean and intimate solid-solid interfaces. During the SPS process, the unique reaction mechanism through the combination of current, pressure and high heating rate allow the formation of desirable solid-solid interfaces between active material particles. Herein, this work focuses on the overview of the application of SPS for fabricating solid-state electrolyte and electrode in all solid-state Li-ion batteries, and beyond, such as solid-state Li-S and Na-ion batteries. The correlations among SPS parameters, interfacial resistance, and electrochemical properties of solid-state electrolytes and electrodes are discussed for different material systems. In the end, we point out future opportunities and challenges associated with SPS application in the hot area of solid-state batteries. It is expected that this timely review will stimulate more fundamental and applied research in the development of solid-state batteries by SPS.

Particle track identification: application of a new technique to apollo helmets.

PubMed

Fleischer, R L; Hart, H R; Giard, W R

1970-12-11

The Apollo helmets are being used to record the dose of heavy particles to which astronauts are exposed on space missions. An improved method for examining and identifying the etched tracks of heavy charged particles consists of replicating tracks and measuring the etching rate as a function of position along the track. Tracks have been observed in Apollo helmets that correspond to ionized atoms heavier than iron.

Progress and prospect on failure mechanisms of solid-state lithium batteries

NASA Astrophysics Data System (ADS)

Ma, Jun; Chen, Bingbing; Wang, Longlong; Cui, Guanglei

2018-07-01

By replacing traditional liquid organic electrolyte with solid-state electrolyte, the solid-state lithium batteries powerfully come back to the energy storage field due to their eminent safety and energy density. In recent years, a variety of solid-state lithium batteries based on excellent solid-state electrolytes are developed. However, the performance degradation of solid-state lithium batteries during cycling and storing is still a serious challenge for practical application. Therefore, this review summarizes the research progress of solid-state lithium batteries from the perspectives of failure phenomena and failure mechanisms. Additionally, the development of methodologies on studying the failure mechanisms of solid-state lithium batteries is also reviewed. Moreover, some perspectives on the remaining questions for understanding the failure behaviors and achieving long cycle life, high safety and high energy density solid-state lithium batteries are presented. This review will help researchers to recognize the status of solid-state lithium batteries objectively and attract much more research interest in conquering the failure issues of solid-state lithium batteries.

78 FR 2695 - Privacy Act of 1974; System of Records

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-14

... data elements used in the Workplace Environment Tracking System (WETS), a new electronic national..., Workplace Harassment Fact Finding, Threat Assessment Case Tracking, and Workplace Environment Intervention... tracking system for these four processes will reasonably assure that workplace harassment policies and...

On the influence of etch pits in the overall dissolution rate of apatite basal sections

NASA Astrophysics Data System (ADS)

Alencar, Igor; Guedes, Sandro; Palissari, Rosane; Hadler, Julio C.

2015-09-01

Determination of efficiencies for particle detection plays a central role for proper estimation of reaction rates. If chemical etching is employed in the revelation of latent particle tracks in solid-state detectors, dissolution rates and etchable lengths are important factors governing the revelation and observation. In this work, the mask method, where a reference part of the sample is protected during dissolution, was employed to measure step heights in basal sections of apatite etched with a nitric acid, HNO, solution at a concentration of 1.1 M and a temperature of 20 °C. We show a drastic increase in the etching velocity as the number of etch pits in the surface augments, in accordance with the dissolution stepwave model, where the outcrop of each etch pit generates a continuous sequence of stepwaves. The number of etch pits was varied by irradiation with neutrons and perpendicularly incident heavy ions. The size dependence of the etch-pit opening with etching duration for ion (200-300 MeV 152Sm and 238U) tracks was also investigated. There is no distinction for the etch pits between the different ions, and the dissolution seems to be governed by the opening velocity when a high number of etch pits are present in the surface. Measurements of the etchable lengths of these ion tracks show an increase in these lengths when samples are not pre-annealed before irradiation. We discuss the implications of these findings for fission-track modelling.

Solid oxide fuel cells fueled with reducible oxides

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chuang, Steven S.; Fan, Liang Shih

A direct-electrochemical-oxidation fuel cell for generating electrical energy includes a cathode provided with an electrochemical-reduction catalyst that promotes formation of oxygen ions from an oxygen-containing source at the cathode, a solid-state reduced metal, a solid-state anode provided with an electrochemical-oxidation catalyst that promotes direct electrochemical oxidation of the solid-state reduced metal in the presence of the oxygen ions to produce electrical energy, and an electrolyte disposed to transmit the oxygen ions from the cathode to the solid-state anode. A method of operating a solid oxide fuel cell includes providing a direct-electrochemical-oxidation fuel cell comprising a solid-state reduced metal, oxidizing themore » solid-state reduced metal in the presence of oxygen ions through direct-electrochemical-oxidation to obtain a solid-state reducible metal oxide, and reducing the solid-state reducible metal oxide to obtain the solid-state reduced metal.« less

Evaluation of Causes of Large 96-H and 120-H Track Errors in the Western North Pacific

DTIC Science & Technology

2006-06-01

Interpolated GFS (A) forecast track for 11W ( Mawar ) for the 0600 UTC 22 August 2005 E-DCI-m case study. The solid sections of the forecast tracks...fields for 11W ( Mawar ) predicted by GFS for taus (a) 54 and (c) 66 for 0600 UTC 22 August 2005 and the corresponding verifying 00-h NOGAPS analyses...pressure (mb) fields for 11W ( Mawar ) predicted by GFS for taus (a) 90 and (c) 114 for 0600 UTC 22 August 2005 and the corresponding verifying 00-h

Satellite-tracking and Earth dynamics research programs

NASA Technical Reports Server (NTRS)

1981-01-01

The major focus for operations during this period was the preliminary MERIT Campaign and its intensive tracking of LAGEOS for polar motion and Earth rotation studies. The data acquired from LAGEOS were used for other geophysical investigations, including studies of crustal dynamics, and Earth and ocean tides, and for the general development of precision orbit determination. The network performed regular tracking of several other retroreflector satellites including GEOS-1, GEOS-3, BE-C, and Starlette for refined determinations of station coordinates and Earth's gravity field and for studies of solid Earth dynamics.

Near- Source, Seismo-Acoustic Signals Accompanying a NASCAR Race at the Texas Motor Speedway

NASA Astrophysics Data System (ADS)

Stump, B. W.; Hayward, C.; Underwood, R.; Howard, J. E.; MacPhail, M. D.; Golden, P.; Endress, A.

2014-12-01

Near-source, seismo-acoustic observations provide a unique opportunity to characterize urban sources, remotely sense human activities including vehicular traffic and monitor large engineering structures. Energy separately coupled into the solid earth and atmosphere provides constraints on not only the location of these sources but also the physics of the generating process. Conditions and distances at which these observations can be made are dependent upon not only local geological conditions but also atmospheric conditions at the time of the observations. In order to address this range of topics, an empirical, seismo-acoustic study was undertaken in and around the Texas Motor Speedway in the Dallas-Ft. Worth area during the first week of April 2014 at which time a range of activities associated with a series of NASCAR races occurred. Nine, seismic sensors were deployed around the 1.5-mile track for purposes of documenting the direct-coupled seismic energy from the passage of the cars and other vehicles on the track. Six infrasound sensors were deployed on a rooftop in a rectangular array configuration designed to provide high frequency beam forming for acoustic signals. Finally, a five-element infrasound array was deployed outside the track in order to characterize how the signals propagate away from the sources in the near-source region. Signals recovered from within the track were able to track and characterize the motion of a variety of vehicles during the race weekend including individual racecars. Seismic data sampled at 1000 sps documented strong Doppler effects as the cars approached and moved away from individual sensors. There were faint seismic signals that arrived at seismic velocity but local acoustic to seismic coupling as supported by the acoustic observations generated the majority of seismic signals. Actual seismic ground motions were small as demonstrated by the dominance of regional seismic signals from a magnitude 4.0 earthquake that arrived at the local seismometers as the race began. The infrasound arrays recorded a variety of atmosphere only processes including substantial helicopter traffic although the array outside the track did not capture the details of the race as a result of the rapid attenuation of high frequency signals.

Computer program TRACK_TEST for calculating parameters and plotting profiles for etch pits in nuclear track materials

NASA Astrophysics Data System (ADS)

Nikezic, D.; Yu, K. N.

2006-01-01

A computer program called TRACK_TEST for calculating parameters (lengths of the major and minor axes) and plotting profiles in nuclear track materials resulted from light-ion irradiation and subsequent chemical etching is described. The programming steps are outlined, including calculations of alpha-particle ranges, determination of the distance along the particle trajectory penetrated by the chemical etchant, calculations of track coordinates, determination of the lengths of the major and minor axes and determination of the contour of the track opening. Descriptions of the program are given, including the built-in V functions for the two commonly employed nuclear track materials commercially known as LR 115 (cellulose nitrate) and CR-39 (poly allyl diglycol carbonate) irradiated by alpha particles. Program summaryTitle of the program:TRACK_TEST Catalogue identifier:ADWT Program obtainable from:CPC Program Library, Queen's University of Belfast, N. Ireland Program summary URL:http://cpc.cs.qub.ac.uk/summaries/ADWT Computer:Pentium PC Operating systems:Windows 95+ Programming language:Fortran 90 Memory required to execute with typical data:256 MB No. of lines in distributed program, including test data, etc.: 2739 No. of bytes in distributed program, including test data, etc.:204 526 Distribution format:tar.gz External subprograms used:The entire code must be linked with the MSFLIB library Nature of problem: Fast heavy charged particles (like alpha particles and other light ions etc.) create latent tracks in some dielectric materials. After chemical etching in aqueous NaOH or KOH solutions, these tracks become visible under an optical microscope. The growth of a track is based on the simultaneous actions of the etchant on undamaged regions (with the bulk etch rate V) and along the particle track (with the track etch rate V). Growth of the track is described satisfactorily by these two parameters ( V and V). Several models have been presented in the past describing the track development, one of which is the model of Nikezic and Yu (2003) [D. Nikezic, K.N. Yu, Three-dimensional analytical determination of the track parameters. Over-etched tracks, Radiat. Meas. 37 (2003) 39-45] used in the present program. The present computer program has been written to calculate coordinates of points on the track wall and to determine other relevant track parameters. Solution method:Coordinates of points on the track wall assuming normal incidence were calculated by using the method as described by Fromm et al. (1988) [M. Fromm, A. Chambaudet, F. Membrey, Data bank for alpha particle tracks in CR39 with energies ranging from 0.5 to 5 MeV recording for various incident angles, Nucl. Tracks Radiat. Meas. 15 (1988) 115-118]. The track is then rotated through the incident angle in order to obtain the coordinates of the oblique track [D. Nikezic, K.N. Yu, Three-dimensional analytical determination of the track parameters. Over-etched tracks, Radiat. Meas. 37 (2003) 39-45; D. Nikezic, Three dimensional analytical determination of the track parameters, Radiat. Meas. 32 (2000) 277-282]. In this way, the track profile in two dimensions (2D) was obtained. In the next step, points in the track wall profile are rotated around the particle trajectory. In this way, circles that outline the track in three dimensions (3D) are obtained. The intersection between the post-etching surface of the detector and the 3D track is the track opening (or the track contour). Coordinates of the track 2D and 3D profiles and the track opening are saved in separate output data files. Restrictions: The program cannot calculate track parameters for the incident angle of exactly 90°. The alpha-particle energy should be smaller than 10 MeV. Furthermore, the program cannot perform calculations for tracks in some extreme cases, such as for very low incident energies or very small incident angles. Additional comments: This is a freeware, but publications arising from using this program should cite the present paper and the paper describing the track growth model [D. Nikezic, K.N. Yu, Three-dimensional analytical determination of the track parameters. Over-etched tracks, Radiat. Meas. 37 (2003) 39-45]. Moreover, the references for the V functions used should also be cited. For the CR-39 detector: Function (1): S.A. Durrani, R.K. Bull, Solid State Nuclear Track Detection. Principles, Methods and Applications, Pergamon Press, 1987. Function (2): C. Brun, M. Fromm, M. Jouffroy, P. Meyer, J.E. Groetz, F. Abel, A. Chambaudet, B. Dorschel, D. Hermsdorf, R. Bretschneider, K. Kadner, H. Kuhne, Intercomparative study of the detection characteristics of the CR-39 SSNTD for light ions: Present status of the Besancon-Dresden approaches, Radiat. Meas. 31 (1999) 89-98. Function (3): K.N. Yu, F.M.F. Ng, D. Nikezic, Measuring depths of sub-micron tracks in a CR-39 detector from replicas using atomic force microscopy, Radiat. Meas. 40 (2005) 380-383. For the LR 115 detector: Function (1): S.A. Durrani, P.F. Green, The effect of etching conditions on the response of LR 115, Nucl. Tracks 8 (1984) 21-24. Function (2): C.W.Y. Yip, D. Nikezic, J.P.Y Ho, K.N. Yu, Chemical etching characteristics for cellulose nitrate, Mat. Chem. Phys. 95 (2005) 307-312. Running time: Order of several minutes, dependent on input parameters and the resolution requested by the user.

A simple and effective process for noise reduction of multichannel cortical field potential recordings in freely moving rats.

PubMed

Shaw, Fu-Zen; Yen, Chen Tung; Chen, Ruei Feng

2003-04-15

Simple and useful steps, i.e. placing a grounded plate under the recording chamber as well as using multiple reference electrodes, are introduced here for obtaining reliable low-noise recordings of brain activity in freely moving rats. A general circuit model was built to analyze the electrical interference of both single-grounded and two-reference ground-free recording configurations. In both simulated and realistic conditions under two recording states, 60-Hz magnitude was in the microvolt range. Moreover, the noise was significantly reduced by shortening the distance between the subject and the grounded plate under the recording chamber. Furthermore, in chronically implanted rats, average 60-Hz interference of multichannel electroencephalograms of two-reference ground-free recordings (3.74 +/- 0.18 microV) was significantly smaller than that of the single-grounded condition (9.03 +/- 1.98 microV). Thus, we demonstrated that a lower-noise recording can be achieved by a two-reference configuration and a closely-placed metal grounded plate in an open-field circumstance. As compared to the use of a Faraday cage, this simple procedure is of benefit for long-term behavioral tracking with a video camera and for pharmacological experiments.

Solidify, An LLVM pass to compile LLVM IR into Solidity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kothapalli, Abhiram

The software currently compiles LLVM IR into Solidity (Ethereum’s dominant programming language) using LLVM’s pass library. Specifically, his compiler allows us to convert an arbitrary DSL into Solidity. We focus specifically on converting Domain Specific Languages into Solidity due to their ease of use, and provable properties. By creating a toolchain to compile lightweight domain-specific languages into Ethereum's dominant language, Solidity, we allow non-specialists to effectively develop safe and useful smart contracts. For example lawyers from a certain firm can have a proprietary DSL that codifies basic laws safely converted to Solidity to be securely executed on the blockchain. Inmore » another example, a simple provenance tracking language can be compiled and securely executed on the blockchain.« less

40 CFR 1068.501 - How do I report emission-related defects?

Code of Federal Regulations, 2010 CFR

2010-07-01

... methods for tracking, investigating, reporting, and correcting emission-related defects. In your request... aggregate in tracking, identifying, investigating, evaluating, reporting, and correcting potential and... it is actually defective. Note that this paragraph (b)(2) does not require data-tracking or recording...

Peak impact accelerations during track and treadmill running.

PubMed

Bigelow, Erin M R; Elvin, Niell G; Elvin, Alex A; Arnoczky, Steven P

2013-10-01

To determine whether peak vertical and horizontal impact accelerations were different while running on a track or on a treadmill, 12 healthy subjects (average age 32.8 ± 9.8 y), were fitted with a novel, wireless accelerometer capable of recording triaxial acceleration over time. The accelerometer was attached to a custom-made acrylic plate and secured at the level of the L5 vertebra via a tight fitting triathlon belt. Each subject ran 4 miles on a synthetic, indoor track at a self-selected pace and accelerations were recorded on three perpendicular axes. Seven days later, the subjects ran 4 miles on a treadmill set at the individual runner's average pace on the track and the peak vertical and horizontal impact magnitudes between the track and treadmill were compared. There was no difference (P = .52) in the average peak vertical impact accelerations between the track and treadmill over the 4 mile run. However, peak horizontal impact accelerations were greater (P = .0012) on the track when compared with the treadmill. This study demonstrated the feasibility for long-term impact accelerations monitoring using a novel wireless accelerometer.

Comparison of radon doses based on different radon monitoring approaches.

PubMed

Vaupotič, Janja; Smrekar, Nataša; Žunić, Zora S

2017-04-01

In 43 places (23 schools, 3 kindergartens, 16 offices and one dwelling), indoor radon has been monitored as an intercomparison experiment, using α-scintillation cells (SC - Jožef Stefan Institute, Slovenia), various kinds of solid state nuclear track detectors (KfK - Karlsruhe Institute of Technology, Germany; UFO - National Institute of Radiological Sciences, Chiba, Japan; RET - University College Dublin, Ireland) and active electronic devices (EQF, Sarad, Germany). At the same place, the radon levels and, consequently, the effective doses obtained with different radon devices differed substantially (by a factor of 2 or more), and no regularity was observed as regards which detector would show a higher or lower dose. Copyright © 2016 Elsevier Ltd. All rights reserved.

Design, fabrication, test and delivery of a K-band antenna breadboard model

NASA Technical Reports Server (NTRS)

1974-01-01

The results of a research effort to develop a Ku-Band single channel monopulse antenna with significant improvements in efficiency and bandwidth are reported. A single aperture, multimode horn, utilized in a near field Cassegrainian configuration, was the technique selected for achieving the desired efficiency and bandwidth performance. In order to provide wide polarization flexibility, a wire grid, space filter polarizer was developed. A solid state switching network with appropriate driving electronics provides the receive channel sum and difference signal interface with an existing Apollo type tracking electronics subsystem. A full scale breadboard model of the antenna was fabricated and tested. Performance of the model was well within the requirements and goals of the contract.

In vitro cell irradiation systems based on 210Po alpha source: construction and characterisation

NASA Technical Reports Server (NTRS)

Szabo, J.; Feher, I.; Palfalvi, J.; Balashazy, I.; Dam, A. M.; Polonyi, I.; Bogdandi, E. N.

2002-01-01

One way of studying the risk to human health of low-level radiation exposure is to make biological experiments on living cell cultures. Two 210Po alpha-particle emitting devices, with 0.5 and 100 MBq activity, were designed and constructed to perform such experiments irradiating monolayers of cells. Estimates of dose rate at the cell surface were obtained from measurements by a PIPS alpha-particle spectrometer and from calculations by the SRIM 2000, Monte Carlo charged particle transport code. Particle fluence area distributions were measured by solid state nuclear track detectors. The design and dosimetric characterisation of the devices are discussed. c2002 Elsevier Science Ltd. All rights reserved.

The Emission, Lifetimes, and Formation Threshold of the Vegard-Kaplan Transition of Solid Nitrogen Exposed to Far-ultraviolet Radiation

NASA Astrophysics Data System (ADS)

Lu, Hsiao-Chi; Lo, Jen-Iu; Peng, Yu-Chain; Chou, Sheng-Lung; Lin, Meng-Yeh; Cheng, Bing-Ming

2016-11-01

Irradiation of solid nitrogen at 4 K with far-ultraviolet light from a synchrotron caused excitation to the upper state of the Vegard-Kaplan (VK) system; the emission in that system was simultaneously recorded in wavelength region 200-440 nm. The lifetimes of emission lines for VK (0, 1) to (0, 12) transitions were measured in the range of 2.12 ˜ 2.65 s. The threshold wavelength to observe the VK emission was 175.0 ± 3.5 nm, corresponding to energy 7.08 ± 0.14 eV. This investigation of the generation of icy VK nitrogen enhances our understanding of its photochemistry in space.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Doukas, S.; Madesis, I.; Dimitriou, A.

We present SIMION 8.1 Monte Carlo type simulations of the response function and detection solid angle for long lived Auger states (lifetime τ ∼ 10{sup −9} − 10{sup −5} s) recorded by a hemispherical spectrograph with injection lens and position sensitive detector used for high resolution Auger spectroscopy of ion beams. Also included in these simulations for the first time are kinematic effects particular to Auger emission from fast moving projectile ions such as line broadening and solid angle limitations allowing for a more accurate and realistic line shape modeling. Our results are found to be in excellent agreement withmore » measured electron line shapes of both long lived 1s2s2p{sup 4}P and prompt Auger projectile states formed by electron capture in collisions of 25.3 MeV F{sup 7+} with H{sub 2} and 12.0 MeV C{sup 4+} with Ne recorded at 0{sup ∘} to the beam direction. These results are important for the accurate evaluation of the 1s2s2p {sup 4}P/{sup 2}P ratio of K-Auger cross sections whose observed non-statistical production by electron capture into He-like ions, recently a field of interesting interpretations, awaits further resolution.« less

Recent experiences with implementing a video based six degree of freedom measurement system for airplane models in a 20 foot diameter vertical spin tunnel

NASA Technical Reports Server (NTRS)

Snow, Walter L.; Childers, Brooks A.; Jones, Stephen B.; Fremaux, Charles M.

1993-01-01

A model space positioning system (MSPS), a state-of-the-art, real-time tracking system to provide the test engineer with on line model pitch and spin rate information, is described. It is noted that the six-degree-of-freedom post processor program will require additional programming effort both in the automated tracking mode for high spin rates and in accuracy to meet the measurement objectives. An independent multicamera system intended to augment the MSPS is studied using laboratory calibration methods based on photogrammetry to characterize the losses in various recording options. Data acquired to Super VHS tape encoded with Vertical Interval Time Code and transcribed to video disk are considered to be a reasonable priced choice for post editing and processing video data.

Functional subdivisions in low-frequency primary auditory cortex (AI).

PubMed

Wallace, M N; Palmer, A R

2009-04-01

We wished to test the hypothesis that there are modules in low-frequency AI that can be identified by their responsiveness to communication calls or particular regions of space. Units were recorded in anaesthetised guinea pig AI and stimulated with conspecific vocalizations and a virtual motion stimulus (binaural beats) presented via a closed sound system. Recording tracks were mainly oriented orthogonally to the cortical surface. Some of these contained units that were all time-locked to the structure of the chutter call (14/22 tracks) and/or the purr call (12/22 tracks) and/or that had a preference for stimuli from a particular region of space (8/20 tracks with four contralateral, two ipsilateral and two midline), or where there was a strong asymmetry in the response to beats of different direction (two tracks). We conclude that about half of low-frequency AI is organized into modules that are consistent with separate "what" and "where" pathways.

AUTOMATIC COUNTER

DOEpatents

Robinson, H.P.

1960-06-01

An automatic counter of alpha particle tracks recorded by a sensitive emulsion of a photographic plate is described. The counter includes a source of mcdulated dark-field illumination for developing light flashes from the recorded particle tracks as the photographic plate is automatically scanned in narrow strips. Photoelectric means convert the light flashes to proportional current pulses for application to an electronic counting circuit. Photoelectric means are further provided for developing a phase reference signal from the photographic plate in such a manner that signals arising from particle tracks not parallel to the edge of the plate are out of phase with the reference signal. The counting circuit includes provision for rejecting the out-of-phase signals resulting from unoriented tracks as well as signals resulting from spurious marks on the plate such as scratches, dust or grain clumpings, etc. The output of the circuit is hence indicative only of the tracks that would be counted by a human operator.

Molecular dynamics modelling of solidification in metals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boercker, D.B.; Belak, J.; Glosli, J.

1997-12-31

Molecular dynamics modeling is used to study the solidification of metals at high pressure and temperature. Constant pressure MD is applied to a simulation cell initially filled with both solid and molten metal. The solid/liquid interface is tracked as a function of time, and the data are used to estimate growth rates of crystallites at high pressure and temperature in Ta and Mg.

Complete (1)H resonance assignment of beta-maltose from (1)H-(1)H DQ-SQ CRAMPS and (1)H (DQ-DUMBO)-(13)C SQ refocused INEPT 2D solid-state NMR spectra and first principles GIPAW calculations.

PubMed

Webber, Amy L; Elena, Bénédicte; Griffin, John M; Yates, Jonathan R; Pham, Tran N; Mauri, Francesco; Pickard, Chris J; Gil, Ana M; Stein, Robin; Lesage, Anne; Emsley, Lyndon; Brown, Steven P

2010-07-14

A disaccharide is a challenging case for high-resolution (1)H solid-state NMR because of the 24 distinct protons (14 aliphatic and 10 OH) having (1)H chemical shifts that all fall within a narrow range of approximately 3 to 7 ppm. High-resolution (1)H (500 MHz) double-quantum (DQ) combined rotation and multiple pulse sequence (CRAMPS) solid-state NMR spectra of beta-maltose monohydrate are presented. (1)H-(1)H DQ-SQ CRAMPS spectra are presented together with (1)H (DQ)-(13)C correlation spectra obtained with a new pulse sequence that correlates a high-resolution (1)H DQ dimension with a (13)C single quantum (SQ) dimension using the refocused INEPT pulse-sequence element to transfer magnetization via one-bond (13)C-(1)H J couplings. Compared to the observation of only a single broad peak in a (1)H DQ spectrum recorded at 30 kHz magic-angle spinning (MAS), the use of DUMBO (1)H homonuclear decoupling in the (1)H DQ CRAMPS experiment allows the resolution of distinct DQ correlation peaks which, in combination with first-principles chemical shift calculations based on the GIPAW (Gauge Including Projector Augmented Waves) plane-wave pseudopotential approach, enables the assignment of the (1)H resonances to the 24 distinct protons. We believe this to be the first experimental solid-state NMR determination of the hydroxyl OH (1)H chemical shifts for a simple sugar. Variable-temperature (1)H-(1)H DQ CRAMPS spectra reveal small increases in the (1)H chemical shifts of the OH resonances upon decreasing the temperature from 348 K to 248 K.

Measurement of cosmic-ray muons with the Distributed Electronic Cosmic-ray Observatory, a network of smartphones

NASA Astrophysics Data System (ADS)

Vandenbroucke, J.; BenZvi, S.; Bravo, S.; Jensen, K.; Karn, P.; Meehan, M.; Peacock, J.; Plewa, M.; Ruggles, T.; Santander, M.; Schultz, D.; Simons, A. L.; Tosi, D.

2016-04-01

Solid-state camera image sensors can be used to detect ionizing radiation in addition to optical photons. We describe the Distributed Electronic Cosmic-ray Observatory (DECO), an app and associated public database that enables a network of consumer devices to detect cosmic rays and other ionizing radiation. In addition to terrestrial background radiation, cosmic-ray muon candidate events are detected as long, straight tracks passing through multiple pixels. The distribution of track lengths can be related to the thickness of the active (depleted) region of the camera image sensor through the known angular distribution of muons at sea level. We use a sample of candidate muon events detected by DECO to measure the thickness of the depletion region of the camera image sensor in a particular consumer smartphone model, the HTC Wildfire S. The track length distribution is fit better by a cosmic-ray muon angular distribution than an isotropic distribution, demonstrating that DECO can detect and identify cosmic-ray muons despite a background of other particle detections. Using the cosmic-ray distribution, we measure the depletion thickness to be 26.3 ± 1.4 μm. With additional data, the same method can be applied to additional models of image sensor. Once measured, the thickness can be used to convert track length to incident polar angle on a per-event basis. Combined with a determination of the incident azimuthal angle directly from the track orientation in the sensor plane, this enables direction reconstruction of individual cosmic-ray events using a single consumer device. The results simultaneously validate the use of cell phone camera image sensors as cosmic-ray muon detectors and provide a measurement of a parameter of camera image sensor performance which is not otherwise publicly available.

Smoked aluminum track stations record flying squirrel occurrence

Treesearch

Martin G. Raphael; Cathy A. Taylor; Reginald H. Barrett

1986-01-01

Smoked aluminum track stations are a useful technique for studying patterns of abundance and distribution of northern flying squirrel (Glaucomys sabrinus). They are easily transported to remote field sites, allow permanent preservation of tracks, and yield frequency-of-occurrence information. A study in Douglas-fir (Pseseudotsuga menziesii...

21 CFR 1271.290 - Tracking.

Code of Federal Regulations, 2010 CFR

2010-04-01

... TISSUE-BASED PRODUCTS Current Good Tissue Practice § 1271.290 Tracking. (a) General. If you perform any... designed to facilitate effective tracking, using the distinct identification code, from the donor to the... for recording the distinct identification code and type of each HCT/P distributed to a consignee to...

Multisensor fusion for 3D target tracking using track-before-detect particle filter

NASA Astrophysics Data System (ADS)

Moshtagh, Nima; Romberg, Paul M.; Chan, Moses W.

2015-05-01

This work presents a novel fusion mechanism for estimating the three-dimensional trajectory of a moving target using images collected by multiple imaging sensors. The proposed projective particle filter avoids the explicit target detection prior to fusion. In projective particle filter, particles that represent the posterior density (of target state in a high-dimensional space) are projected onto the lower-dimensional observation space. Measurements are generated directly in the observation space (image plane) and a marginal (sensor) likelihood is computed. The particles states and their weights are updated using the joint likelihood computed from all the sensors. The 3D state estimate of target (system track) is then generated from the states of the particles. This approach is similar to track-before-detect particle filters that are known to perform well in tracking dim and stealthy targets in image collections. Our approach extends the track-before-detect approach to 3D tracking using the projective particle filter. The performance of this measurement-level fusion method is compared with that of a track-level fusion algorithm using the projective particle filter. In the track-level fusion algorithm, the 2D sensor tracks are generated separately and transmitted to a fusion center, where they are treated as measurements to the state estimator. The 2D sensor tracks are then fused to reconstruct the system track. A realistic synthetic scenario with a boosting target was generated, and used to study the performance of the fusion mechanisms.

An 80 kyr-long continuous speleothem record from Dim Cave, SW Turkey with paleoclimatic implications for the Eastern Mediterranean

PubMed Central

Ünal-İmer, Ezgi; Shulmeister, James; Zhao, Jian-Xin; Tonguç Uysal, I.; Feng, Yue-Xing; Duc Nguyen, Ai; Yüce, Galip

2015-01-01

Speleothem-based stable isotope records are valuable in sub-humid and semi-arid settings where many other terrestrial climate proxies are fragmentary. The Eastern Mediterranean is one such region. Here we present an 80-kyr-long precisely-dated (by U-series) and high-resolution oxygen (δ18O) and carbon (δ13C) records from Dim Cave (~36°N) in SW Turkey. The glacial-interglacial δ18O variations in the Dim Cave speleothem are best explained in terms of changes in the trajectories of winter westerly air masses. These are along a northerly (European) track (isotopically less depleted) during the early last glaciation but are gradually depressed southward closer to the modern westerly track along the North African coast (more depleted) after c.50 kyr and remain in the southern track through the Last Glacial Maximum. The southward displacement of the westerly track reflects growth of the Fennoscandian ice sheet and its impact on westerly wind fields. Changes in δ13C are interpreted as reflecting soil organic matter composition and/or thickness. δ13C values are significantly more negative in interglacials reflecting active carbonic acid production in the soil and less negative in glacial times reflecting carbonate rock values. Several Heinrich events are recorded in the Dim record indicating intensification of westerly flow across this part of the EM. PMID:26337921

13C CP MAS NMR and GIAO-CHF/DFT calculations of flavonoids: Morin, kaempferol, tricin, genistein, formononetin and 3,7-dihydroxyflavone

NASA Astrophysics Data System (ADS)

Zielińska, Agnieszka; Paradowska, Katarzyna; Jakowski, Jacek; Wawer, Iwona

2008-02-01

13C CP MAS NMR spectra of the flavonoids: morin, kaempferol, 3,7-dihydroxyflavone, tricin and isoflavones: genistein and formononetin were recorded to characterize solid-state conformations. Intramolecular hydrogen bonds forming five-, six- and seven-membered rings are present in the two morin molecules in the crystals - their 13C resonances have been assigned with the aid of the calculated shielding constants. Linear relationships between the calculated shielding constants σDFT (ppm) and chemical shifts ( δCPMAS, ppm) were obtained for all studied compounds. Higher correlation coefficients suggest that the conformation with "clockwise" orientation of both OH groups is more probable in the solid 3,7-dihydroxyflavone, whereas in the solid formononetin the OH and OCH 3 substituents are directed "anticlockwise". The barrier to the rotation of phenyl ring B decreases in the order: morin (2'-OH, 3-OH) > kaempferol (3-OH) > tricin.

Phenological cues intrinsic in indigenous knowledge systems for forecasting seasonal climate in the Delta State of Nigeria

NASA Astrophysics Data System (ADS)

Fitchett, Jennifer M.; Ebhuoma, Eromose

2018-06-01

Shifts in the timing of phenological events in plants and animals are cited as one of the most robust bioindicators of climate change. Much effort has thus been placed on the collection of phenological datasets, the quantification of the rates of phenological shifts and the association of these shifts with recorded meteorological data. These outputs are of value both in tracking the severity of climate change and in facilitating more robust management approaches in forestry and agriculture to changing climatic conditions. However, such an approach requires meteorological and phenological records spanning multiple decades. For communities in the Delta State of Nigeria, small-scale farming communities do not have access to meteorological records, and the dissemination of government issued daily to seasonal forecasts has only taken place in recent years. Their ability to survive inter-annual to inter-decadal climatic variability and longer-term climatic change has thus relied on well-entrenched indigenous knowledge systems (IKS). An analysis of the environmental cues that are used to infer the timing and amount of rainfall by farmers from three communities in the Delta State reveals a reliance on phenological events, including the croaking of frogs, the appearance of red millipedes and the emergence of fresh rubber tree and cassava leaves. These represent the first recorded awareness of phenology within the Delta State of Nigeria, and a potentially valuable source of phenological data. However, the reliance of these indicators is of concern given the rapid phenological shifts occurring in response to climate change.

Phenological cues intrinsic in indigenous knowledge systems for forecasting seasonal climate in the Delta State of Nigeria

NASA Astrophysics Data System (ADS)

Fitchett, Jennifer M.; Ebhuoma, Eromose

2017-12-01

Shifts in the timing of phenological events in plants and animals are cited as one of the most robust bioindicators of climate change. Much effort has thus been placed on the collection of phenological datasets, the quantification of the rates of phenological shifts and the association of these shifts with recorded meteorological data. These outputs are of value both in tracking the severity of climate change and in facilitating more robust management approaches in forestry and agriculture to changing climatic conditions. However, such an approach requires meteorological and phenological records spanning multiple decades. For communities in the Delta State of Nigeria, small-scale farming communities do not have access to meteorological records, and the dissemination of government issued daily to seasonal forecasts has only taken place in recent years. Their ability to survive inter-annual to inter-decadal climatic variability and longer-term climatic change has thus relied on well-entrenched indigenous knowledge systems (IKS). An analysis of the environmental cues that are used to infer the timing and amount of rainfall by farmers from three communities in the Delta State reveals a reliance on phenological events, including the croaking of frogs, the appearance of red millipedes and the emergence of fresh rubber tree and cassava leaves. These represent the first recorded awareness of phenology within the Delta State of Nigeria, and a potentially valuable source of phenological data. However, the reliance of these indicators is of concern given the rapid phenological shifts occurring in response to climate change.

Phenological cues intrinsic in indigenous knowledge systems for forecasting seasonal climate in the Delta State of Nigeria.

PubMed

Fitchett, Jennifer M; Ebhuoma, Eromose

2018-06-01

Shifts in the timing of phenological events in plants and animals are cited as one of the most robust bioindicators of climate change. Much effort has thus been placed on the collection of phenological datasets, the quantification of the rates of phenological shifts and the association of these shifts with recorded meteorological data. These outputs are of value both in tracking the severity of climate change and in facilitating more robust management approaches in forestry and agriculture to changing climatic conditions. However, such an approach requires meteorological and phenological records spanning multiple decades. For communities in the Delta State of Nigeria, small-scale farming communities do not have access to meteorological records, and the dissemination of government issued daily to seasonal forecasts has only taken place in recent years. Their ability to survive inter-annual to inter-decadal climatic variability and longer-term climatic change has thus relied on well-entrenched indigenous knowledge systems (IKS). An analysis of the environmental cues that are used to infer the timing and amount of rainfall by farmers from three communities in the Delta State reveals a reliance on phenological events, including the croaking of frogs, the appearance of red millipedes and the emergence of fresh rubber tree and cassava leaves. These represent the first recorded awareness of phenology within the Delta State of Nigeria, and a potentially valuable source of phenological data. However, the reliance of these indicators is of concern given the rapid phenological shifts occurring in response to climate change.

Towards a 1000 tracks digital tape recorder

NASA Technical Reports Server (NTRS)

Coutellier, J. M.; Castera, J. P.; Colineau, J.; Lehureau, J. C.; Maurice, F.; Hanna, C.

1993-01-01

As the demand for high data rate (up to 1 Gb/s), high density (down to 1 sq micron/bit) tape recorder increases, the main investigation trend is an improvement of the well known helical scan concept. The drawbacks of this technology are also well known; sophisticated mechanics, head to tape contact, and wear problems. In our fixed head approach, the recorder mechanics is made much more simple, but the complexity is turned towards the integrated magnetic components, which have to record and reproduce hundreds of tracks in parallel. Our multiplexed write inductive head and magneto-optical readout head will be described, and the global system performances evaluated.

The use of hydrodynamic vortex separators and screening systems to improve water quality.

PubMed

Andoh, R Y G; Saul, A J

2003-01-01

The paper reviews the evolution of Hydrodynamic Vortex Separators (HDVS) in the context of application as high rate rotary flow separators for achieving water quality improvements to meet with regulatory requirements in Europe and North America. The types of HDVS and their application for the control of wet-weather discharges such as combined sewer overflows (CSOs), sanitary sewer overflows (SSOs) and stormwater are outlined and a number of myths surrounding their use, dispelled. Reference is made to outputs of peer reviewed comprehensive monitoring, evaluation and demonstration projects on pilot and full-scale installations to demonstrate the efficacy and extensive track record of these systems. Recent developments and innovations in HDVS technologies are discussed, focusing on their combined use as solids liquid separators, contact vessels for wastewater disinfection, the incorporation of self-cleansing screening devices for the control of aesthetic pollutants (e.g. floatables) and the use of computational modelling for optimisation.

Fast widely-tunable single-frequency 2-micron laser for remote-sensing applications

NASA Astrophysics Data System (ADS)

Henderson, Sammy W.; Hale, Charley P.

2017-08-01

We are developing a family of fast, widely-tunable cw diode-pumped single frequency solid-state lasers, called Swift. The Swift laser architecture is compatible with operation using many different solid-state laser crystals for operation at various emission lines between 1 and 2.1 micron. The initial prototype Swift laser using a Tm,Ho:YLF laser crystal near 2.05 micron wavelength achieved over 100 mW of single frequency cw output power, up to 50 GHz-wide, fast, mode-hop-free piezoelectric tunability, and 100 kHz/ms frequency stability. For the Tm,Ho:YLF laser material, the fast 50 GHz tuning range can be centered at any wavelength from 2047-2059 nm using appropriate intracavity spectral filters. The frequency stability and power are sufficient to serve as the local oscillator (LO) laser in long-range coherent wind-measuring lidar systems, as well as a frequency-agile master oscillator (MO) or injection-seed source for larger pulsed transmitter lasers. The rapid and wide frequency tunablity meets the requirements for integrated-path or range-resolved differential absorption lidar or applications where targets with significantly different line of sight velocities (Doppler shifts) must be tracked. Initial demonstration of an even more compact version of the Swift is also described which requires less prime power and produces less waste heat.

The state of municipal solid waste management in Israel.

PubMed

Daskal, Shira; Ayalon, Ofira; Shechter, Mordechai

2018-06-01

Regulation is a key tool for implementing municipal solid waste (MSW) management strategies and plans. While local authorities in Israel are responsible for the storage, collection, and disposal of MSW, Israel's Ministry of Environmental Protection (MoEP) is responsible for the formulation and implementation of waste management policies and legislation. For the past 12 years, about 80% of the MSW in Israel has been landfilled and recycling rates have not increased, despite regulations. This paper presents the state of MSW management in Israel in light of the MoEP's strategic goal of landfilling reduction, the regulations and legislation designed and implemented for achieving this goal, and the ensuing results. Among other things, the results indicate the importance of monitoring and assessing policy and regulations to examine whether regulation is in fact effective and whether it keeps track of its own targets and goals or not. It is also concluded that even when there is an extensive regulation that includes a wide range of laws, economic penalties and financial incentives (such as landfill levy and financing of MSW separation at source arrangements), this does not guarantee proper treatment or even an improvement in waste management. The key to success is first and foremost a suitable infrastructure that will enable achievement of the desired results.

Contributions of the NOAA Hollings Undergraduate Scholarship Program to the Geosciences Pipeline

NASA Astrophysics Data System (ADS)

Kaplan, M.

2016-12-01

Since 2005, the NOAA Ernest F. Hollings Undergraduate Scholarship Program has provided tuition support and paid summer internship opportunities at NOAA to exceptional students majoring in the geosciences. The purpose of the scholarship program is to train students in NOAA mission fields. Multiple methods were used to track the career trajectories of Hollings alumni, including mining LinkedIn data, conducting an impact analysis based on a professionally developed web-based evaluation survey, and a web-based alumni update system. At least one postgraduate record was recorded for 80% of Hollings Scholarship alumni. Of the alumni reached, more than 75% continued on to graduate school in a NOAA mission field, and 86% of those graduate degrees were in a NOAA mission field or other STEM field. More than 60% of alumni had at least one professional record, with the most alumni working in private industry, followed by nongovernmental organizations and federal, state and local government.

Negotiating Access to Health Information to Promote Students' Health.

PubMed

Radis, Molly E; Updegrove, Stephen C; Somsel, Anne; Crowley, Angela A

2016-04-01

Access to student health information, such as immunizations, screenings, and care plans for chronic conditions, is essential for school nurses to fulfill their role in promoting students' health. School nurses typically encounter barriers to accessing health records and spend many hours attempting to retrieve health information. As a result, nurses' time is poorly utilized and students may suffer adverse outcomes including delayed school entry. In response to this pressing public health issue, a school medical advisor and director of school nurses in a local health department successfully negotiated access for school nurses to three health record systems: a state immunization tracking system, an electronic lead surveillance program, and an electronic health record system. This negotiation process is presented within a framework of the Theory of Diffusion of Innovation and provides a strategy for other school nurses seeking access to student health information. © The Author(s) 2015.

Development of a statewide trauma registry using multiple linked sources of data.

PubMed Central

Clark, D. E.

1993-01-01

In order to develop a cost-effective method of injury surveillance and trauma system evaluation in a rural state, computer programs were written linking records from two major hospital trauma registries, a statewide trauma tracking study, hospital discharge abstracts, death certificates, and ambulance run reports. A general-purpose database management system, programming language, and operating system were used. Data from 1991 appeared to be successfully linked using only indirect identifying information. Familiarity with local geography and the idiosyncracies of each data source were helpful in programming for effective matching of records. For each individual case identified in this way, data from all available sources were then merged and imported into a standard database format. This inexpensive, population-based approach, maintaining flexibility for end-users with some database training, may be adaptable for other regions. There is a need for further improvement and simplification of the record-linkage process for this and similar purposes. PMID:8130556

As the nation goes, so goes Maine?

PubMed

Kilbreth, Elizabeth

2014-06-01

Historically, Maine has been a state with generous safety net programs and a track record of innovative efforts in health system reform, developed under the leadership of Democratic administrations and with frequent support from moderate Republicans. But the 2010 elections in Maine dramatically changed the political balance of power, anointing both a governor and a legislature ideologically at odds with the state's recent political past. Maine has become a bastion of resistance to the Patient Protection and Affordable Care Act, with a reduced Medicaid program, defunded state access initiative, and no state exchange. In addition, the state has adopted a laissez-faire approach to insurance market dysfunction. Using Maine as a case study of the shifts in national political mood, this article describes in broad brushstrokes Maine's history of health reform efforts and recent shift in political direction, and discusses some of the factors that contributed to the change. Copyright © 2014 by Duke University Press.

Twelve years of tracking 52-Hz whale calls from a unique source in the North Pacific

NASA Astrophysics Data System (ADS)

Watkins, William A.; Daher, Mary Ann; George, Joseph E.; Rodriguez, David

2004-12-01

A unique whale call with 50-52 Hz emphasis from a single source has been tracked over 12 years in the central and eastern North Pacific. These calls, referred to as 52-Hz calls, were monitored and analyzed from acoustic data recorded by hydrophones of the US Navy Sound Surveillance System (SOSUS) and other arrays. The calls were noticed first in 1989, and have been detected and tracked since 1992. No other calls with similar characteristics have been identified in the acoustic data from any hydrophone system in the North Pacific basin. Only one series of these 52-Hz calls has been recorded at a time, with no call overlap, suggesting that a single whale produced the calls. The calls were recorded from August to February with most in December and January. The species producing these calls is unknown. The tracks of the 52-Hz whale were different each year, and varied in length from 708 to 11,062 km with travel speeds ranging from 0.7 to 3.8 km/h. Tracks included (A) meandering over short ranges, (B) predominantly west-to-east movement, and (C) mostly north-to-south travel. These tracks consistently appeared to be unrelated to the presence or movement of other whale species (blue, fin and humpback) monitored year-round with the same hydrophones.

Standard B-Mode Ultrasound Measures Local Carotid Artery Characteristics as Reliably as Radiofrequency Phase Tracking in Symptomatic Carotid Artery Patients.

PubMed

Steinbuch, Jeire; Hoeks, Arnold P G; Hermeling, Evelien; Truijman, Martine T B; Schreuder, Floris H B M; Mess, Werner H

2016-02-01

Local arterial stiffness can be assessed with high accuracy and precision by measuring arterial distension on the basis of phase tracking of radiofrequency ultrasound signals acquired at a high frame rate. However, in clinical practice, B-mode ultrasound registrations are made at a low frame rate (20-50 Hz). We compared the accuracy and intra-subject precision of edge tracking and phase tracking distension in symptomatic carotid artery patients. B-mode ultrasound recordings (40 mm, 37 fps) and radiofrequency recordings (31 lines covering 29 mm, 300 fps) were acquired from the left common carotid artery of 30 patients (aged 45-88 y) with recent cerebrovascular events. To extract the distension, semi-automatic echo edge and phase tracking algorithms were applied to B-mode and radiofrequency recordings, respectively. Both methods exhibited a similar intra-subject precision for distension (standard deviation = 44 μm and 47 μm, p = 0.66) and mean distension (difference: -6 ± 69 μm, p = 0.67). Intra-subject distension inhomogeneity tends to be larger for edge tracking (difference: 15 ± 35 μm, p = 0.04). Standard B-mode scanners are suitable for measuring local artery characteristics in symptomatic carotid artery patients with good precision and accuracy. Copyright © 2016 World Federation for Ultrasound in Medicine & Biology. Published by Elsevier Inc. All rights reserved.