Sample records for solvent eds process

  1. Chemical analysis and biological testing of materials from the EDS coal liquefaction process: a status report

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Later, D.W.; Pelroy, R.A.; Wilson, B.W.

    1984-05-01

    Representative process materials were obtained from the EDS pilot plant for chemical and biological analyses. These materials were characterized for biological activity and chemical composition using a microbial mutagenicity assay and chromatographic and mass spectrometric analytical techniques. The two highest boiling distillation cuts, as well as process solvent (PS) obtained from the bottoms recycle mode operation, were tested for initiation of mouse skin tumorigenicity. All three materials were active; the crude 800/sup 0 +/F cut was substantially more potent than the crude bottoms recycle PS or 750 to 800/sup 0/F distillate cut. Results from chemical analyses showed the EDS materials,more » in general, to be more highly alkylated and have higher hydroaromatic content than analogous SRC II process materials (no in-line process hydrogenation) used for comparison. In the microbial mutagenicity assays the N-PAC fractions showed greater activity than did the aliphatic hydrocarbon, hydroxy-PAH, or PAH fractions, although mutagenicity was detected in certain PAH fractions by a modified version of the standard microbial mutagenicity assay. Mutagenic activities for the EDS materials were lower, overall, than those for the corresponding materials from the SRC II process. The EDS materials produced under different operational modes had distinguishable differences in both their chemical constituency and biological activity. The primary differences between the EDS materials studied here and their SRC II counterparts used for comparison are most likely attributable to the incorporation of catalytic hydrogenation in the EDS process. 27 references, 28 figures, 27 tables.« less

  2. Effect of Nd:YAG laser on the solvent evaporation of adhesive systems.

    PubMed

    Batista, Graziela Ribeiro; Barcellos, Daphne Câmara; Rocha Gomes Torres, Carlos; Damião, Álvaro José; de Oliveira, Hueder Paulo Moisés; de Paiva Gonçalves, Sérgio Eduardo

    2015-01-01

    This study evaluated the influence of Nd:YAG laser on the evaporation degree (ED) of the solvent components in total-etch and self-etch adhesives. The ED of Gluma Comfort Bond (Heraeus-Kulzer) one-step self-etch adhesive, and Adper Single Bond 2 (3M ESPE), and XP Bond (Dentsply) total-etch adhesives was determined by weight alterations using two techniques: Control--spontaneous evaporation of the solvent for 5 min; Experimental--Nd:YAG laser irradiation for 1 min, followed by spontaneous evaporation for 4 min. The weight loss due to evaporation of the volatile components was measured at baseline and after 10 s, 20 s, 30 s, 40 s, 50 s, 60 s, 70 s, 80 s, 90 s, 100 s, 110 s, 2 min, 3 min, 4 min, and 5 min. Evaporation of solvent components significantly increased with Nd:YAG laser irradiation for all adhesives investigated. Gluma Comfort Bond showed significantly higher evaporation of solvent components than Adper Single Bond 2 and XP Bond. All the adhesives lost weight quickly during the first min of Nd:YAG laser irradiation. The application of Nd:YAG laser on adhesives before light curing had a significant effect on the evaporation of the solvent components, and the ED of Gluma Comfort Bond one-step self-etch adhesive was significantly higher than with Adper Single Bond 2 and XP Bond total-etch adhesives. The use of the Nd:YAG laser on the uncured adhesive technique can promote a greater ED of solvents, optimizing the longevity of the adhesive restorations.

  3. The Language of Energy: A Glossary of Words and Phrases Used in the Energy Industry.

    ERIC Educational Resources Information Center

    American Petroleum Inst., Washington, DC.

    Provided is an alphabetical list or words and phrases commonly used in the energy industry. Entries range from such general terms as biomass, fossil fuels, and wetlands to such highly specific terms as Arab oil embargo of 1973-74 and Exxon Donor Solvent (EDS) Process. (JN)

  4. Solvent Effects on Emission Yield and Lifetime for Coumarin Laser Dyes. Requirements for a Rotatory Decay Mechanism.

    DTIC Science & Technology

    1983-10-31

    spectral shifts and sizeable solvent iso- tope effects have been frequently observed for solvent exciplexes , e in contrast to our findings. The results also...49. Chandross, E. A.; "The Exciplex " Gordon, M.; Ware, W. R. (ed.) 4 Academic Press, Inc.: New York; 1975; p 187. SO. a. Beecroft, R. A.; Davidson, R

  5. PWR steam generator chemical cleaning, Phase I. Final report

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Rothstein, S.

    1978-07-01

    United Nuclear Industries (UNI) entered into a subcontract with Consolidated Edison Company of New York (Con Ed) on August 8, 1977, for the purpose of developing methods to chemically clean the secondary side tube to tube support crevices of the steam generators of Indian Point Nos. 1 and 2 PWR plants. This document represents the first reporting on activities performed for Phase I of this effort. Specifically, this report contains the results of a literature search performed by UNI for the purpose of determining state-of-the-art chemical solvents and methods for decontaminating nuclear reactor steam generators. The results of the searchmore » sought to accomplish two objectives: (1) identify solvents beyond those proposed at present by UNI and Con Ed for the test program, and (2) confirm the appropriateness of solvents and methods of decontamination currently in use by UNI.« less

  6. Diagnostic Tools for Performance Evaluation of Innovative In-Situ Remediation Technologies at Chlorinated Solvent-Contaminated Sites

    DTIC Science & Technology

    2011-11-01

    within a groundwater sample or within a biofilm . FISH probes have been developed that target chlorinated solvent- degrading populations, such as...1988. Bacterial metabolism of protein and endogenous nitrogen compounds. In I.R. Rowland (ed.), Role of the gut flora in toxicity and cancer (p. 227

  7. Synthesis and characterization of NiO nanopowder by sol-gel process

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Ningsih, Sherly Kasuma Warda

    2015-09-30

    Preparation of nickel oxide (NiO) nanopowder by sol-gel process has been studied. NiO nanopowders were obtained by sol-gel method by using nickel nitrate hexahydrate and sodium hydroxide and aquadest were used as precursor, agent precipitator and solvent, respectively. The powders were formed by drying at 110°C and followed by heating in the furnace at 400°C for 1.5 hours. The product was obtained black powder. The product was characterized by Energy Dispesive X-ray Fluorescence (ED-XRF), X-ray diffraction (XRD) and Scanning Electron Microscopy (SEM). The ED-XRF pattern shows the composition of NiO produced was 97.1%. The XRD pattern showed NiO forms weremore » produced generally in monoclinic stucture. The crystalline size of NiO was obtained in the range 40-85 nm. SEM micrograph clearly showed that powder had a spherical with uniform distribution size is 0.1-1.0 µm approximately.« less

  8. Constant pH Molecular Dynamics in Explicit Solvent with Enveloping Distribution Sampling and Hamiltonian Exchange

    PubMed Central

    2015-01-01

    We present a new computational approach for constant pH simulations in explicit solvent based on the combination of the enveloping distribution sampling (EDS) and Hamiltonian replica exchange (HREX) methods. Unlike constant pH methods based on variable and continuous charge models, our method is based on discrete protonation states. EDS generates a hybrid Hamiltonian of different protonation states. A smoothness parameter s is used to control the heights of energy barriers of the hybrid-state energy landscape. A small s value facilitates state transitions by lowering energy barriers. Replica exchange between EDS potentials with different s values allows us to readily obtain a thermodynamically accurate ensemble of multiple protonation states with frequent state transitions. The analysis is performed with an ensemble obtained from an EDS Hamiltonian without smoothing, s = ∞, which strictly follows the minimum energy surface of the end states. The accuracy and efficiency of this method is tested on aspartic acid, lysine, and glutamic acid, which have two protonation states, a histidine with three states, a four-residue peptide with four states, and snake cardiotoxin with eight states. The pKa values estimated with the EDS-HREX method agree well with the experimental pKa values. The mean absolute errors of small benchmark systems range from 0.03 to 0.17 pKa units, and those of three titratable groups of snake cardiotoxin range from 0.2 to 1.6 pKa units. This study demonstrates that EDS-HREX is a potent theoretical framework, which gives the correct description of multiple protonation states and good calculated pKa values. PMID:25061443

  9. Characterization of solids deposited on the modular caustic-side solvent extraction unit (MCU) coalescer media removed in May and October 2014

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Fondeur, F. F.

    During routine maintenance, the coalescers utilized in the Modular Caustic-Side Solvent Extraction Unit (MCU) processing of Salt Batch 6 and a portion of Salt Batch 7 were sampled and submitted to the Savannah River National Laboratory (SRNL) for characterization, for the purpose of identifying solid phase constituents that may be accumulating in these coalescers. Specifically, two samples were received and characterized: A decontaminated salt solution (DSS) coalescer sample and a strip effluent (SE) coalescer sample. Aliquots of the samples were analyzed by XRD, Fourier Transform Infrared (FTIR) Spectroscopy, SEM, and EDS. Other aliquots of the samples were leached in acidmore » solution, and the leachates were analyzed by ICP-AES. In addition, modeling was performed to provide a basis for comparison of the analytical results.« less

  10. Ultrasound assisted synthesis of iron doped TiO2 catalyst.

    PubMed

    Ambati, Rohini; Gogate, Parag R

    2018-01-01

    The present work deals with synthesis of Fe (III) doped TiO 2 catalyst using the ultrasound assisted approach and conventional sol-gel approach with an objective of establishing the process intensification benefits. Effect of operating parameters such as Fe doping, type of solvent, solvent to precursor ratio and initial temperature has been investigated to get the best catalyst with minimum particle size. Comparison of the catalysts obtained using the conventional and ultrasound assisted approach under the optimized conditions has been performed using the characterization techniques like DLS, XRD, BET, SEM, EDS, TEM, FTIR and UV-Vis band gap analysis. It was established that catalyst synthesized by ultrasound assisted approach under optimized conditions of 0.4mol% doping, irradiation time of 60min, propan-2-ol as the solvent with the solvent to precursor ratio as 10 and initial temperature of 30°C was the best one with minimum particle size as 99nm and surface area as 49.41m 2 /g. SEM analysis, XRD analysis as well as the TEM analysis also confirmed the superiority of the catalyst obtained using ultrasound assisted approach as compared to the conventional approach. EDS analysis also confirmed the presence of 4.05mol% of Fe element in the sample of 0.4mol% iron doped TiO 2 . UV-Vis band gap results showed the reduction in band gap from 3.2eV to 2.9eV. Photocatalytic experiments performed to check the activity also confirmed that ultrasonically synthesized Fe doped TiO 2 catalyst resulted in a higher degradation of Acid Blue 80 as 38% while the conventionally synthesized catalyst resulted in a degradation of 31.1%. Overall, the work has clearly established importance of ultrasound in giving better catalyst characteristics as well as activity for degradation of the Acid Blue 80 dye. Copyright © 2017 Elsevier B.V. All rights reserved.

  11. Biodegradable polyester-based eco-composites containing hemp fibers modified with macrocyclic oligomers

    NASA Astrophysics Data System (ADS)

    Conzatti, Lucia; Utzeri, Roberto; Hodge, Philip; Stagnaro, Paola

    2016-05-01

    An original compatibilizing pathway for hemp fibers/poly(1,4-butylene adipate-co-terephtalate) (PBAT) eco-composites was explored exploiting the capability of macrocyclic oligomers (MCOs), obtained by cyclodepolymerization (CDP) of PBAT at high dilution, of being re-converted into linear chains by entropically-driven ring-opening polymerization (ED-ROP) that occurs simply heating the MCOS in the bulk. CDP reaction of PBAT was carried out varying solvent, catalyst and reaction time. Selected MCOs were used to adjust the conditions of the ED-ROP reaction. The best experimental conditions were then adopted to modify hemp fibers. Eco-composites based on PBAT and hemp fibers as obtained or modified with PBAT macrocyclics or oligomers were prepared by different process strategies. The best fiber-PBAT compatibility was observed when the fibers were modified with PBAT oligomers before incorporation in the polyester matrix.

  12. SWITCHABLE POLARITY SOLVENTS AS DRAW SOLUTES FOR FORWARD OSMOSIS

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Frederick F. Stewart; Mark L. Stone; Aaron D. Wilson

    2013-03-01

    Switchable polarity solvents (SPS), mixtures of carbon dioxide, water, and tertiary amines, are presented as viable forward osmosis (FO) draw solutes allowing a novel SPS FO process. In this study substantial osmotic strengths of SPS are measured with freezing point osmometry and were demonstrated to induce competitive ?uxes at high salt concentrations on a laboratory-scale FO unit utilizing a ?at sheet cellulose triacetate (CTA) membrane. Under the experimental conditions the SPS degrades the CTA membrane; however experiments with polyamide reverse osmosis (RO) membranes display stability towards SPS. Once the draw is diluted the major fraction of the switchable polarity solventmore » can be mechanically separated from the puri?ed water after polar to nonpolar phase shift induced by introduction of 1 atm carbon dioxide to 1 atm of air or nitrogen with mild heating. Trace amounts of SPS can be removed from the separated water with RO in a process that avoids solution concentration polarization. The separated nonpolar phase can be regenerated to a full strength draw and recycled with the re-addition of 1 atm of carbon dioxide.« less

  13. Highly crystalline films of PCPDTBT with branched side chains by solvent vapor crystallization: influence on opto-electronic properties.

    PubMed

    Fischer, Florian S U; Trefz, Daniel; Back, Justus; Kayunkid, Navaphun; Tornow, Benjamin; Albrecht, Steve; Yager, Kevin G; Singh, Gurpreet; Karim, Alamgir; Neher, Dieter; Brinkmann, Martin; Ludwigs, Sabine

    2015-02-18

    PCPDTBT, a marginally crystallizable polymer, is crystallized into a new crystal structure using solvent-vapor annealing. Highly ordered areas with three different polymer-chain orientations are identified using TEM/ED, GIWAXS, and polarized Raman spectroscopy. The optical and structural properties differ significantly from films prepared by standard device preparation protocols. Bilayer solar cells, however, show similar performance. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  14. EFFECT OF DEUTERIUM OXIDE ON LOCAL ANESTHETIC ACTIVITY OF PROCAINE

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Susina, S.V.; Hiter, F.D.; Siegel, F.P.

    1962-12-01

    Since it appears that D/sub 2/O is toxic in animals only when the concentration in the body fluids reaches high levels (> 20%), and since D/sub 2/O resembles the common solvent protium oxide more closely than any other, possible pharmaceutical applications of this solvent were explored. In studies in mice, D/ sub 2/O was used as a solvent for procaine and the effect on the stability and local anesthetic activity was noted. The ED/sub 50/ was determined by the method using corneal sensitivity, and comparison was made with procaine solutions in H/ sub 2/O. In H/sub 2/O the ED/sub 50/more » was 1.8% while in D/sub 2/O it was 1.0%. The LD/sub 50/was determined by intraperitoneal injection in mice. There appeared to be no significant difference in the toxicity of procaine in either solvent. Stability studies indicate that procaine is more stable in D/sub 2/O than H/sub 2/O at apparent pH values of 8.0, 8.5, and 9.0. Hence, the increased local anesthetic activity of procaine in D/sub 2/O may be accounted for by the fact that procaine free base is more stable in D/sub 2/O solutions, or that at the same apparent pH a D/sub 2/O solution of procaine will contain more free base than in the corresponding aqueous solution. (H.H.D.)« less

  15. Consumption of energy drinks among Québec college students.

    PubMed

    Picard-Masson, Marianne; Loslier, Julie; Paquin, Pierre; Bertrand, Karine

    2017-03-01

    Consumption of energy drinks (ED) raises concerns because of adverse health effects possibly linked with high levels of caffeine and sugar intake. The study looks at the scope of ED consumption as well as some of the associated characteristics. Thirty-six public colleges in the Canadian province of Québec agreed to participate in a descriptive cross-sectional study (n = 36). In February 2013, participating colleges invited their students to answer an online questionnaire on consumption of ED, alcoholic ED (AED), and ED in combination with other psychotropic drugs. A descriptive and correlational analysis was carried out. Logistic regressions explored associations between ED consumption and associated characteristics. Of the students who successfully completed the questionnaire and participated in the study (n = 10,283), a low proportion consumed ED (9.1%; n = 935) and/or AED (1.1%; n = 109) at least once a week in the previous month. Although low in proportion, a number of participants reported having used ED with other stimulant psychoactive substances (n = 247) and ≥3 ED/day (n = 193) or ≥3 AED/occasion (n = 167), which can pose a risk for serious adverse effects. Weekly ED consumption was associated with consumption of ≥20 cups of coffee/week, smoking, excessive use of alcohol and past use of cannabis, glues or solvents and amphetamines. A majority of respondents are not heavy users of ED, AED, or ED with drugs. Yet, the profiles of ED consumption potentially harmful to health that characterize some participants indicate that the potential health consequences of such behaviour are of concern.

  16. Biodegradation of Chlorinated Solvents: Reactions near DNAPL and Enzyme Function

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    McCarty, P. L.; Spormann, Alfred M.; Criddle, Craig, S.

    Chlorinated solvents are among the most widespread groundwater contaminants in the country, contamination which is also among the most difficult and expensive for remediation. These solvents are biodegradable in the absence of oxygen, but this biodegradation requires both a food source for the organisms (electron donor) and the presence of chlorinated solvent biodegrading organisms. These two requirements are present naturally at some contamination sites, leading to natural attenuation of the solvents. If one or both requirements are absent, then engineered bioremediation either through addition of an external electron donor or through bioaugmentation with appropriate microorganisms, or both, may be usedmore » for site remediation. The most difficult case for cleanup is when a large residual of undissolved chlorinated solvents are present, residing as dense -non-aqueous-phase- liquid ( DNAPL). A major focus of this study was on the potential for biodegradation of the solvents when pre sent as DNAPL where concentrations are very high and potential for toxicity to microorganisms exist. Another focus was on a better understanding of the biological mechanisms involved in chlorinated solvent biodegradation . These studies were directed towards the chlorinated solvents, trichloroethene (TCE), tetrachloroethene or perchloroethene (PCE), and carbon tetrachloride (CT). The potential for biodegradation of TCE and PCE DNAPL was clearly demonstrated in this research. From column soil studies and batch studies we found there to be a clear advantage in focusing efforts at bioremediation near the DNAPL. Here, chlorinated solvent concentrations are the highest, both because of more favorable reaction kinetics and because such high solvent concentrations are toxic to microorganisms, such as methanogens, which compete with dehalogenators for the electron donor. Additionally, biodegradation near a PCE DNAPL results in an enhanced dissolution rate for the chlorinated solvent, by factors of three to five times, leading to a more rapid clean-up of the DNAPL zone. The most favored electron donor to add is one which partitions well with the chlorinated solvent or can be concentrated near it. Unfortunately, an ideal electron donor, such as vegetable oil, is difficult to introduce and mix with DNAPL in the ground, doing this properly remains an engineering challenge. Numerical model studies have indicated that several factors may significantly influence the rate and extent of enhancement, including the inhibitory effects of PCE and cDCE, the level of ED concentration, DNAPL configuration, and competition for ED. Such factors need to be considered when contemplating engineered DNAPL bioremediation. Pseudomonas stuzeri KC is an organism that transforms CT to carbon dioxide and chloride without the formation of the hazardous intermediate, chloroform. This is accomplished by production and secretion of a molecule called PDTC. This study was direct ed towards determining how PDTC works. Cu (II) at a ratio of 1:1 Cu to PDTC was found to result in the most rapid CT transformation, confirming that the PDTC-Cu complex is both a reactant and a catalyst in CT transformation. CT degradation requires that the PDTC be in a reduced form, which is generated by contact with cell components. Fe(II) inhibits CT transformation by PDTC. Studies indicated that this inhibition is enhanced by some compound or factor in the supernatant with molecular weight greater than 10,000 Da. We have made progress in determining what this factor might be, but have not yet been able to identify it. In related studies, we found that CT transformation by another organism, Shewanella oneidensis MR1, also involves an excreted factor, but this factor is different from PDTC and results in chloroform transformation as an intermediate. Our studies have indicated that this factor is similar to vitamin K2, and we have also confirmed that vitamin K2 does transform C T into chloroform.« less

  17. Permanent physico-chemical properties of extremely diluted aqueous solutions of homeopathic medicines.

    PubMed

    Elia, V; Baiano, S; Duro, I; Napoli, E; Niccoli, M; Nonatelli, L

    2004-07-01

    The purpose of this study was to obtain information about the influence of successive dilutions and succussions on the water structure. 'Extremely diluted solutions' (EDS) are solutions obtained through the iteration of two processes: dilution in stages of 1:100 and succussion, typically used in homeopathic medicine. The iteration is repeated until extreme dilutions are reached, so that the chemical composition of the solution is identical to that of the solvent. Nine different preparations, were studied from the 3cH to 30cH (Hahnemannian Centesimal Dilution). Four of those were without the active principle (potentized water). Two different active principles were used: Arsenicum sulphuratum rubrum (ASR), As4S4, 2,4-dichlorophenoxyacetic acid (2,4D). The solvents were: a solution of sodium bicarbonate and of silicic acid at 5 x 10(-5) M (mol/l) each, and solutions of sodium bicarbonate 5 x 10(-5), 7.5 x 10(-5) and 10 x 10(-5) M (mol/l) in double-distilled water. The containers were Pyrex glass to avoid the release of alkaline oxide and silica from the walls. Conductivity measurements of the solutions were carried out as a function of the age of the potencies. We found increases of electrical conductivity compared to untreated solvent. Successive dilution and succussion can permanently alter the physico-chemical properties of the aqueous solvent. But we also detected changes in physio-chemical parameters with time. This has not previously been reported. The modification of the solvent could provide an important support to the validity of homeopathic medicine, that employs 'medicines without molecules'. The nature of the phenomena here described remains still unexplained, nevertheless some significant experimental results were obtained.

  18. On the Use of Enveloping Distribution Sampling (EDS) to Compute Free Enthalpy Differences between Different Conformational States of Molecules: Application to 310-, α-, and π-Helices.

    PubMed

    Lin, Zhixiong; Liu, Haiyan; Riniker, Sereina; van Gunsteren, Wilfred F

    2011-12-13

    Enveloping distribution sampling (EDS) is a powerful method to compute relative free energies from simulation. So far, the EDS method has only been applied to alchemical free energy differences, i.e., between different Hamiltonians defining different systems, and not yet to obtain free energy differences between different conformations or conformational states of a system. In this article, we extend the EDS formalism such that it can be applied to compute free energy differences of different conformations and apply it to compute the relative free enthalpy ΔG of 310-, α-, and π-helices of an alanine deca-peptide in explicit water solvent. The resulting ΔG values are compared to those obtained by standard thermodynamic integration (TI) and from so-called end-state simulations. A TI simulation requires the definition of a λ-dependent pathway which in the present case is based on hydrogen bonds of the different helical conformations. The values of ⟨(∂VTI)/(∂λ)⟩λ show a sharp change for a particular range of λ values, which is indicative of an energy barrier along the pathway, which lowers the accuracy of the resulting ΔG value. In contrast, in a two-state EDS simulation, an unphysical reference-state Hamiltonian which connects the parts of conformational space that are relevant to the different end states is constructed automatically; that is, no pathway needs to be defined. In the simulation using this reference state, both helices were sampled, and many transitions between them occurred, thus ensuring the accuracy of the resulting free enthalpy difference. According to the EDS simulations, the free enthalpy differences of the π-helix and the 310-helix versus the α-helix are 5 kJ mol(-1) and 47 kJ mol(-1), respectively, for an alanine deca-peptide in explicit SPC water solvent using the GROMOS 53A6 force field. The EDS method, which is a particular form of umbrella sampling, is thus applicable to compute free energy differences between conformational states as well as between systems and has definite advantages over the traditional TI and umbrella sampling methods to compute relative free energies.

  19. Synthesis, characterization and application of a nano-manganese-catalyst as an efficient solid catalyst for solvent free selective oxidation of ethylbenzene, cyclohexene, and benzylalcohol

    NASA Astrophysics Data System (ADS)

    Habibi, Davood; Faraji, Ali Reza

    2013-07-01

    The object of this study is to synthesize the heterogeneous Mn-nano-catalyst (MNC) which has been covalently anchored on a modified nanoscaleSiO2/Al2O3, and characterized by FT-IR, UV-Vis, CHN elemental analysis, EDS, TEM, and EDX. The method is efficient for the highly selective oxidation of ethylbenzene, cyclohexene, and benzylalcohol without the need to any solvents, using tert-butyl hydroperoxide (TBHP) as an oxidant. Oxidation of ethylbenzene, cyclohexene, and benzylalcohol gave acetophenone, 2-cyclohexene-1-one and benzaldehyde, respectively, as major products. Reaction conditions have been optimized by considering the effect of various factors such as reaction time, amounts of substrates and oxidant, Mn-nano-catalyst and application of various solvents.

  20. Ionic Liquids as Solvent, Catalyst Support Chemical Agent Decontamination and Detoxification

    DTIC Science & Technology

    2004-12-15

    agents. 8 3.2 Reactions in surfactant systems Currie studied the reaction between 3-bromo-1-propanol and phenol and a series of phenols carrying...Liquids; Knoche, W., Schomacker, R., Eds.; Springer-Verlag: New York, 1998, pp 1-10. (52) Gonzaga , F.; Perez, E.; Rico-Lattes, I.; Lattes, A. New Journal

  1. (19)F NMR reveals multiple conformations at the dimer interface of the nonstructural protein 1 effector domain from influenza A virus.

    PubMed

    Aramini, James M; Hamilton, Keith; Ma, Li-Chung; Swapna, G V T; Leonard, Paul G; Ladbury, John E; Krug, Robert M; Montelione, Gaetano T

    2014-04-08

    Nonstructural protein 1 of influenza A virus (NS1A) is a conserved virulence factor comprised of an N-terminal double-stranded RNA (dsRNA)-binding domain and a multifunctional C-terminal effector domain (ED), each of which can independently form symmetric homodimers. Here we apply (19)F NMR to NS1A from influenza A/Udorn/307/1972 virus (H3N2) labeled with 5-fluorotryptophan, and we demonstrate that the (19)F signal of Trp187 is a sensitive, direct monitor of the ED helix:helix dimer interface. (19)F relaxation dispersion data reveal the presence of conformational dynamics within this functionally important protein:protein interface, whose rate is more than three orders of magnitude faster than the kinetics of ED dimerization. (19)F NMR also affords direct spectroscopic evidence that Trp187, which mediates intermolecular ED:ED interactions required for cooperative dsRNA binding, is solvent exposed in full-length NS1A at concentrations below aggregation. These results have important implications for the diverse roles of this NS1A epitope during influenza virus infection. Copyright © 2014 Elsevier Ltd. All rights reserved.

  2. Facile preparation of hierarchical nanostructured CuInS2 counter electrodes for dye-sensitized solar cells

    NASA Astrophysics Data System (ADS)

    Dhas, C. Ravi; Christy, A. Jennifer; Venkatesh, R.; Santhoshi Monica, S. Esther; Panda, Subhendu K.; Subramanian, B.; Ravichandran, K.; Sudhagar, P.; Ezhil Raj, A. Moses

    2017-12-01

    CuInS2 (CIS) thin films have been synthesized onto the glass substrates for different solvent volumes (10, 30, 50 and 70 ml) by nebulizer spray technique. The effect of solvent volume on the structural, morphological, compositional, optical and electrical properties of CIS thin films has been investigated. X-ray diffraction patterns suggest that the obtained CIS films are polycrystalline with the tetragonal structure. The surface morphology of the prepared CIS films purely depends on the solvent volume. The elemental quantitative investigation and the stoichiometric ratio of the CIS thin films were verified from XPS and EDS. High absorbance with the optical band gap of 1.13 eV was obtained at the higher solvent volume. All the deposited CIS thin films exhibited p-type semiconducting behavior with the high electrical conductivity and carrier concentration. CIS thin films deposited onto the FTO substrate were used as a counter electrode (CE) in dye-sensitized solar cells. CIS CEs possessed high electrocatalytic behavior and fast electron charge transfer at the CE/electrolyte interface. The CIS CE prepared using 50 ml solvent volume generated high energy conversion efficiency of about 3.25%.

  3. Application of Nucleic Acid-Based Tools for Monitoring Monitored Natural Attenuation (MNA), Biostimulation and Bioaugmentation at Chlorinated Solvent Sites

    DTIC Science & Technology

    2010-12-01

    K. M. Ritalahti, and J. M. Tiedje. 2003. Diversity of Dechlorinating Bacteria, p. 53-87. In M. M. Häggblom and I. D. Bossert (eds.), Dehalogenation ...Anaerobic Microbial Dehalogenation . Annu. Rev. Microbiol. 58:43-73. Smits, T. H.M., C. Devenoges, K. Szynalski, J. Maillard, and C. Holliger. 2004

  4. Additive assisted hydrothermal synthesis, characterization and optical properties of one dimensional DyPO4:Ce3+ nanostructures

    NASA Astrophysics Data System (ADS)

    Khajuria, H.; Kumar, M.; Singh, R.; Ladol, J.; Nawaz Sheikh, H.

    2018-05-01

    One dimensional nanostructures of cerium doped dysprosium phosphate (DyPO4:Ce3+) were synthesized via hydrothermal route in the presence of different surfactants [sodium dodecyl sulfate (SDS), dodecyl sulfosuccinate (DSS), polyvinyl pyrollidone (PVP)] and solvent [ethylene glycol and water]. The prepared nanostructures were characterized by Powder X-ray diffraction (PXRD), Fourier transform infrared spectroscopy (FTIR), Field emission scanning electron microscopy (FE-SEM), Transmission electron microscopy (TEM), energy dispersive spectroscopy (EDS), UV-VIS-NIR absorption spectrophotometer and photoluminescence (PL) studies. The PXRD and FTIR results indicate purity, good crystallinity and effective doping of Ce3+ in nanostructures. SEM and TEM micrographs display nanorods, nanowires and nanobundles like morphology of DyPO4:Ce3+. Energy-dispersive X-ray spectra (EDS) of DyPO4:Ce3+nanostructures confirm the presence of dopant. UV-VIS-NIR absorption spectra of prepared compounds are used to calculate band gap and explore their optical properties. Luminescent properties of DyPO4:Ce3+ was studied by using PL emission spectra. The effect of additives and solvents on the uniformity, morphology and optical properties of the nanostructures were studied in detail.

  5. Cleaning painted surfaces: evaluation of leaching phenomenon induced by solvents applied for the removal of gel residues.

    PubMed

    Casoli, Antonella; Di Diego, Zaira; Isca, Clelia

    2014-12-01

    Cleaning is one of the most important, delicate, and at the same time controversial processes in the conservation treatment of paintings. Although a strict definition of cleaning would be the removal of dirt, grime, or other accretions (surface cleaning), in the conservation field, cleaning is used in the broader meaning to include thinning/removing altered or “unwanted layers” of materials without damaging or altering the physicochemical properties of the surfaces to be preserved. The cleaning of unvarnished paintings is one of the most critical issues that are currently discussed. Several studies exist regarding different cleaning tools, such as gels, soaps, enzymes, ionic liquids, and foams, as well as various dry methods and lasers, but only a few have been performed on the risk associated with the use of water and organic solvents for the cleaning treatments in relation to the original paint binder. The aim of the study is to verify analytically the behavior of water gelling agents during cleaning treatments and the interaction of the following elements: water or organic solvents applied for the removal of gel residues with the original lipid paint binder. For this purpose, the study was conducted on a fragment of canvas painting (sixteenth to seventeenth century) of Soprintendenza per i Beni Storici, Artistici ed Etnoantropologici del Friuli Venezia Giulia (Superintendence for the Historical, Artistic and Ethno-anthropological Heritage of Friuli Venezia Giulia), Udine by means of Fourier transform infrared spectroscopy, gas chromatography/mass spectrometry, and scanning electron microscopy.

  6. Coal liquefaction process with enhanced process solvent

    DOEpatents

    Givens, Edwin N.; Kang, Dohee

    1984-01-01

    In an improved coal liquefaction process, including a critical solvent deashing stage, high value product recovery is improved and enhanced process-derived solvent is provided by recycling second separator underflow in the critical solvent deashing stage to the coal slurry mix, for inclusion in the process solvent pool.

  7. Purification Procedures for Single-Wall Carbon Nanotubes

    NASA Technical Reports Server (NTRS)

    Gorelik, Olga P.; Nikolaev, Pavel; Arepalli, Sivaram

    2001-01-01

    This report summarizes the comparison of a variety of procedures used to purify carbon nanotubes. Carbon nanotube material is produced by the arc process and laser oven process. Most of the procedures are tested using laser-grown, single-wall nanotube (SWNT) material. The material is characterized at each step of the purification procedures by using different techniques including scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), transmission electron microscopy (TEM), Raman, X-ray diffractometry (XRD), thermogravimetric analysis (TGA), nuclear magnetic resonance (NMR), and high-performance liquid chromatography (HPLC). The identified impurities are amorphous and graphitic carbon, catalyst particle aggregates, fullerenes, and hydrocarbons. Solvent extraction and low-temperature annealing are used to reduce the amount of volatile hydrocarbons and dissolve fullerenes. Metal catalysts and amorphous as well as graphitic carbon are oxidized by reflux in acids including HCl, HNO3 and HF and other oxidizers such as H2O2. High-temperature annealing in vacuum and in inert atmosphere helps to improve the quality of SWNTs by increasing crystallinity and reducing intercalation.

  8. Ultrasonication of Bismuth Telluride Nanocrystals Fabricated by Solvothermal Method

    NASA Technical Reports Server (NTRS)

    Chu, Sang-Hyon; Choi, Sang H.; Kim, Jae-Woo; King, Glen C.; Elliott, James R.

    2006-01-01

    The objective of this study is to evaluate the effect of ultrasonication on bismuth telluride nanocrystals prepared by solvothermal method. In this study, a low dimensional nanocrystal of bismuth telluride (Bi2Te3) was synthesized by a solvothermal process in an autoclave at 180 C and 200 psi. During the solvothermal reaction, organic surfactants effectively prevented unwanted aggregation of nanocrystals in a selected solvent while controlling the shape of the nanocrystal. The atomic ratio of bismuth and tellurium was determined by energy dispersive spectroscopy (EDS). The cavitational energy created by the ultrasonic probe was varied by the ultrasonication process time, while power amplitude remained constant. The nanocrystal size and its size distribution were measured by field emission scanning electron microscopy (FESEM) and a dynamic light scattering system. When the ultrasonication time increased, the average size of bismuth telluride nanocrystal gradually increased due to the direct collision of nanocrystals. The polydispersity of the nanocrystals showed a minimum when the ultrasonication was applied for 5 min. Keywords: bismuth telluride, nanocrystal, low-dimensional, ultrasonication, solvothermal

  9. Process for solvent refining of coal using a denitrogenated and dephenolated solvent

    DOEpatents

    Garg, Diwakar; Givens, Edwin N.; Schweighardt, Frank K.

    1984-01-01

    A process is disclosed for the solvent refining of non-anthracitic coal at elevated temperatures and pressure in a hydrogen atmosphere using a hydrocarbon solvent which before being recycled in the solvent refining process is subjected to chemical treatment to extract substantially all nitrogenous and phenolic constituents from the solvent so as to improve the conversion of coal and the production of oil in the solvent refining process. The solvent refining process can be either thermal or catalytic. The extraction of nitrogenous compounds can be performed by acid contact such as hydrogen chloride or fluoride treatment, while phenolic extraction can be performed by caustic contact or contact with a mixture of silica and alumina.

  10. Continuous countercurrent membrane column for the separation of solute/solvent and solvent/solvent systems

    DOEpatents

    Nerad, Bruce A.; Krantz, William B.

    1988-01-01

    A reverse osmosis membrane process or hybrid membrane - complementary separator process for producing enriched product or waste streams from concentrated and dilute feed streams for both solvent/solvent and solute/solvent systems is described.

  11. In Vitro Production of Echioidinin, 7-O-Methywogonin from Callus Cultures of Andrographis lineata and Their Cytotoxicity on Cancer Cells

    PubMed Central

    Mohammed, Arifullah; Chiruvella, Kishore K.; Rao, Yerra Koteswara; Geethangili, Madamanchi; Raghavan, Sathees C.; Ghanta, Rama Gopal

    2015-01-01

    Andrographis lineata is an herbal medicinal plant used in traditional medicine as a substitute for Andrographis paniculata. Here, using mature leaf explants of A. lineata we demonstrate for the first time the callus induction established on MS medium containing 1.0 mg l–1 IAA. Dried callus was subjected to solvent extraction with acetone. Further the acetone residue was separated by silica gel column chromatography, crystallized and characterized on the basis of nuclear magnetic resonance (proton and c13) and liquid chromatographic mass spectroscopy. This analysis revealed the occurrence of two known flavones namely, 7-O-methylwogonin (MW) and Echioidinin (ED). Furthermore, these compounds were tested for their cytotoxicity against leukemic cell line, CEM. We identify that ED and MW induced cytotoxicity in a time- and concentration-dependent manner. Further increase in the LDH release upon treatment with ED and MW further confirmed our cytotoxicity results against leukemic cell line. Strikingly, MW was more potent than ED when compared by trypan blue and MTT assays. Our results recapitulate the utility of callus cultures for the production of plant specific bioactive secondary metabolites instead of using wild plants. Together, our in vitro studies provide new insights of A. lineata callus cultures serving as a source for cancer chemotherapeutic agents. PMID:26488879

  12. Magnesium Electrorefining in Non-Aqueous Electrolyte at Room Temperature

    NASA Astrophysics Data System (ADS)

    Kwon, Kyungjung; Park, Jesik; Kusumah, Priyandi; Dilasari, Bonita; Kim, Hansu; Lee, Churl Kyoung

    Magnesium, of which application is often limited by its poor corrosion resistance, is more vulnerable to corrosion with existence of metal impurities such as Fe. Therefore, for the refining and recycling of magnesium, high temperature electrolysis using molten salts has been frequently adopted. In this report, the purification of magnesium scrap by electrolysis at room temperature is investigated with non-aqueous electrolytes. An aprotic solvent of tetrahydrofuran (THF) was used as a solvent of the electrolyte. Magnesium scrap was used as anode materials and ethyl magnesium bromide (EtMgBr) was dissolved in THF for magnesium source. The purified magnesium can be uniformly electrodeposited on copper electrode under potentiostatic conditions. The deposits were confirmed by scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS) analysis.

  13. Theoretical evidence of charge transfer interaction between SO₂ and deep eutectic solvents formed by choline chloride and glycerol.

    PubMed

    Li, Hongping; Chang, Yonghui; Zhu, Wenshuai; Wang, Changwei; Wang, Chao; Yin, Sheng; Zhang, Ming; Li, Huaming

    2015-11-21

    The nature of the interaction between deep eutectic solvents (DESs), formed by ChCl and glycerol, and SO2 has been systematically investigated using the M06-2X density functional combined with cluster models. Block-localized wave function energy decomposition (BLW-ED) analysis shows that the interaction between SO2 and DESs is dominated by a charge transfer interaction. After this interaction, the SO2 molecule becomes negatively charged, whereas the ChCl-glycerol molecule is positively charged, which is the result of Lewis acid-base interaction. The current result affords a theoretical proof that it is highly useful and efficient to manipulate the Lewis acidity of absorbents for SO2 capture. Moreover, hydrogen bonding as well as electrostatic interactions may also contribute to the stability of the complex. Structure analysis shows that solvent molecules will adjust their geometries to interact with SO2. In addition, the structure of SO2 is barely changed after interaction. The interaction energy between different cluster models and SO2 ranges from -6.8 to -14.4 kcal mol(-1). It is found that the interaction energy is very sensitive to the solvent structure. The moderate interaction between ChCl-glycerol and SO2 is consistent with the concept that highly efficient solvents for SO2 absorption should not only be solvable but also regenerable.

  14. 21 CFR 173.280 - Solvent extraction process for citric acid.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Solvent extraction process for citric acid. 173..., Lubricants, Release Agents and Related Substances § 173.280 Solvent extraction process for citric acid. A solvent extraction process for recovery of citric acid from conventional Aspergillus niger fermentation...

  15. Supercritical crystallization: The RESs-process and the GAS-process

    NASA Astrophysics Data System (ADS)

    Berends, Edwin M.

    1994-09-01

    This Doctoral Ph.D. thesis describes the development of two novel crystallization processes utilizing supercritical fluids either as a solvent, the RESS-process, or as an anti-solvent, the GAS-process. In th RESS-process precipitation of the solute is performed by expansion of the solution over a nozzle to produce ultra-fine, monodisperse particles without any solvent inclusions. In the GAS-process a high pressure gas is dissolved into the liquid phase solvent, where it causes a volumetric expansion of this liquid solvent and lowers the equilibrium solubility. Particle size, particle size distribution and other particle characteristics such as their shape, internal structure and the residual amount of solvent in the particles are expected to be influenced by the liquid phase expansion profile.

  16. 21 CFR 173.280 - Solvent extraction process for citric acid.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Solvent extraction process for citric acid. 173... Solvent extraction process for citric acid. A solvent extraction process for recovery of citric acid from conventional Aspergillus niger fermentation liquor may be safely used to produce food-grade citric acid in...

  17. 21 CFR 173.280 - Solvent extraction process for citric acid.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Solvent extraction process for citric acid. 173... Solvent extraction process for citric acid. A solvent extraction process for recovery of citric acid from conventional Aspergillus niger fermentation liquor may be safely used to produce food-grade citric acid in...

  18. 21 CFR 173.280 - Solvent extraction process for citric acid.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Solvent extraction process for citric acid. 173... Solvent extraction process for citric acid. A solvent extraction process for recovery of citric acid from conventional Aspergillus niger fermentation liquor may be safely used to produce food-grade citric acid in...

  19. Force to Fail Reactions With Monoethanolamine: Application to the Explosive Destruction System

    DTIC Science & Technology

    2014-02-01

    include good solvent properties for agents, miscibility with water, noncorrosivity to stainless steel under typical EDS operating conditions, and low...50%. However, when the HD loading was ≥50%, noticeable amounts of heat were generated and white fumes were observed to form when the reagent was...heat and fumes were generated when the MEA was added to the HD. At loadings ≥ 80%, the neutralent became so viscous it could not be stirred

  20. Rumination, experiential avoidance, and dysfunctional thinking in eating disorders

    PubMed Central

    Rawal, Adhip; Park, Rebecca J.; Williams, J. Mark G.

    2010-01-01

    The majority of research in eating disorders (ED) has investigated the content of disorder-specific thoughts, while few studies have addressed underlying cognitive-affective processes. A better understanding of processes underpinning ED may have important implications for treatment development. Two studies were conducted that investigated levels of rumination, beliefs about rumination, experiential avoidance, and aspects of schematic thinking in individuals with eating pathology. The latter was assessed with a newly designed ED-Sentence Completion Task (ED-SCT). Study 1 (N = 177) examined relations between ED psychopathology and these variables in a student population. Extending this, Study 2 (N = 26) assessed differences between patients with anorexia nervosa and healthy control participants. The results showed that ED psychopathology was related to disorder-specific cognitions, experiential avoidance as well as ruminative brooding but not reflection. A follow-up of anorexia nervosa patients indicated that changes in ED psychopathology were associated with changes in dysfunctional attitudes and maladaptive cognitive-affective processes. These findings highlight cognitive processes that may play an important role in the maintenance of eating pathology. PMID:20598670

  1. Process for removing halogenated aliphatic and aromatic compounds from petroleum products

    DOEpatents

    Googin, J.M.; Napier, J.M.; Travaglini, M.A.

    1983-09-20

    A process is described for removing halogenated aliphatic and aromatic compounds, e.g., polychlorinated biphenyls, from petroleum products by solvent extraction. The halogenated aliphatic and aromatic compounds are extracted from a petroleum product into a polar solvent by contacting the petroleum product with the polar solvent. The polar solvent is characterized by a high solubility for the extracted halogenated aliphatic and aromatic compounds, a low solubility for the petroleum product and considerable solvent power for polyhydroxy compound. The preferred polar solvent is dimethylformamide. A miscible compound, such as, water or a polyhydroxy compound, is added to the polar extraction solvent to increase the polarity of the polar extraction solvent. The halogenated aliphatic and aromatic compounds are extracted from the highly-polarized mixture of water or polyhydroxy compound and polar extraction solvent into a low polar or nonpolar solvent by contacting the water or polyhydroxy compound-polar solvent mixture with the low polar or nonpolar solvent. The halogenated aliphatic and aromatic compounds and the low polar or nonpolar solvent are separated by physical means, e.g., vacuum evaporation. The polar and nonpolar solvents are recovered from recycling. The process can easily be designed for continuous operation. Advantages of the process include that the polar solvent and a major portion of the nonpolar solvent can be recycled, the petroleum products are reclaimable and the cost for disposing of waste containing polychlorinated biphenyls is significantly reduced. 1 fig.

  2. Process for removing halogenated aliphatic and aromatic compounds from petroleum products

    DOEpatents

    Googin, John M.; Napier, John M.; Travaglini, Michael A.

    1983-01-01

    A process for removing halogenated aliphatic and aromatic compounds, e.g., polychlorinated biphenyls, from petroleum products by solvent extraction. The halogenated aliphatic and aromatic compounds are extracted from a petroleum product into a polar solvent by contacting the petroleum product with the polar solvent. The polar solvent is characterized by a high solubility for the extracted halogenated aliphatic and aromatic compounds, a low solubility for the petroleum product and considerable solvent power for polyhydroxy compound. The preferred polar solvent is dimethylformamide. A miscible compound, such as, water or a polyhydroxy compound, is added to the polar extraction solvent to increase the polarity of the polar extraction solvent. The halogenated aliphatic and aromatic compounds are extracted from the highly-polarized mixture of water or polyhydroxy compound and polar extraction solvent into a low polar or nonpolar solvent by contacting the water or polyhydroxy compound-polar solvent mixture with the low polar or nonpolar solvent. The halogenated aliphatic and aromatic compounds and the low polar or nonpolar solvent are separated by physical means, e.g., vacuum evaporation. The polar and nonpolar solvents are recovered from recycling. The process can easily be designed for continuous operation. Advantages of the process include that the polar solvent and a major portion of the nonpolar solvent can be recycled, the petroleum products are reclaimable and the cost for disposing of waste containing polychlorinated biphenyls is significantly reduced.

  3. Process for removing halogenated aliphatic and aromatic compounds from petroleum products. [Polychlorinated biphenyls; methylene chloride; perchloroethylene; trichlorofluoroethane; trichloroethylene; chlorobenzene

    DOEpatents

    Googin, J.M.; Napier, J.M.; Travaglini, M.A.

    1982-03-31

    A process for removing halogenated aliphatic and aromatic compounds, e.g., polychlorinated biphenyls, from petroleum products by solvent extraction. The halogenated aliphatic and aromatic compounds are extracted from a petroleum product into a polar solvent by contracting the petroleum product with the polar solvent. The polar solvent is characterized by a high solubility for the extracted halogenated aliphatic and aromatic compounds, a low solubility for the petroleum product and considerable solvent power for polyhydroxy compound. The preferred polar solvent is dimethylformamide. A miscible polyhydroxy compound, such as, water, is added to the polar extraction solvent to increase the polarity of the polar extraction solvent. The halogenated aliphatic and aromatic compounds are extracted from the highly-polarized mixture of polyhydroxy compound and polar extraction solvent into a low polar or nonpolar solvent by contacting the polyhydroxy compound-polar solvent mixture with the low polar or nonpolar solvent. The halogenated aliphatic and aromatic compounds in the low polar or nonpolar solvent by physical means, e.g., vacuum evaporation. The polar and nonpolar solvents are recovered for recycling. The process can easily be designed for continuous operation. Advantages of the process include that the polar solvent and a major portion of the nonpolar solvent can be recycled, the petroleum products are reclaimable and the cost for disposing of waste containing polychlorinated biphenyls is significantly reduced. 2 tables.

  4. Solvent-Polarity-Induced Active Layer Morphology Control in Crystalline Diketopyrrolopyrrole-Based Low Band Gap Polymer Photovoltaics

    NASA Astrophysics Data System (ADS)

    Ferdous, Sunzida; Liu, Feng; Wang, Dong; Russell, Thomas

    2014-03-01

    The effects of various processing solvents on the morphology of diketopyrrolopyrrole (DPP)-based low band gap polymer (PDPPBT) and phenyl-C71-butyric acid methyl ester (PC71BM) blends are studied. The quality of the processing solvents was varied systematically using a mixture of a non-aromatic polar primary solvent with high boiling point secondary solvents of increasing polarities. An unfavorable solvent-PC71BM interaction affects the growth process of polymer crystallites inside the blend. When non-aromatic polar solvent was used, large PC71BM aggregates were formed that increase in size with the addition of non-polar secondary solvents. When polar solvents were instead used as the secondary solvents, the size scales of the aggregates decrease markedly, creating a percolated fibrillar network. Power conversion efficiencies of 0.03% to 5% are obtained, depending on the solvent system used.

  5. Synthesis and characterization of hollow spherical copper phosphide (Cu 3P) nanopowders

    NASA Astrophysics Data System (ADS)

    Liu, Shuling; Qian, Yitai; Xu, Liqiang

    2009-03-01

    In this paper, hollow spherical Cu 3P nanopowders were synthesized by using copper sulfate pentahydrate (CuSO 4ṡ5H 2O) and yellow phosphorus in a mixed solvent of glycol, ethanol and water at 140-180 ∘C for 12 h. X-ray powder diffraction (XRD), energy dispersive X-ray spectroscopy (EDX), electron diffraction pattern (ED) and transmission electronic microscopy (TEM) studies show that the as-synthesized nanocrystal is pure hexagonal phase Cu 3P with a hollow spherical morphology. Based on the TEM observations, a possible aggregation growth mechanism was proposed for the formation of Cu 3P hollow structures. Meanwhile, the effects of some key factors such as solvents, reaction temperature and reaction time on the final formation of the Cu 3P hollow structure were also discussed.

  6. Effect of organic solvents compared to sandblasting on the repair bond strength of nanohybrid and nanofilled composite resins.

    PubMed

    Brum, Rafael Torres; Vieira, Sergio; Freire, Andrea; Mazur, Rui Fernando; De Souza, Evelise Machado; Rached, Rodrigo Nunes

    2017-01-01

    This study evaluated the effect of different surface treatments on the repair bond strength of nanohybrid (Empress Direct) and nanofilled (Filtek Z350 XT) composite resins. A total of 120 specimens of each material (7.5 x 4.5 x 3 mm) were prepared and polished with SiC paper. Half of the specimens were kept in water for seven days and the other half for six months; they were then divided into six groups according to the type of surface treatment: negative control (no treatment), Al2O3sandblasted, liquid acetone, acetone gel, liquid alcohol and alcohol gel. Following application of the silane coupling agent and the adhesive system, composite resin cylinders were fabricated on the specimens and light cured (20 seconds). The same composite resins were used for the repair. Additionally, ten intact specimens of each composite resin (without repair) were prepared (positive control). The specimens were then loaded to failure in the microshear mode. Three additional specimens were fabricated in each group, and the surface treatments were analyzed by atomic force microscopy, energy-dispersive X-ray spectroscopy (EDS) and scanning electron microscopy (SEM). The nanofilled composite resin showed higher cohesive strength and repair bond strength than the nanohybrid composite resin. The aging process affected the repair bond strength of the nanofilled composite resin. Al2O3sandblasting was more efficient for the nanofilled composite resin and promoted greater surface roughness in both materials. The solvents demonstrated higher efficacy for the nanohybrid composite resin. The strengths resulting from the solvents were material dependent, and Al2O3sandblasting resulted in superior repair bond strength in both materials.

  7. Engineering Nucleotide Specificity of Succinyl-CoA Synthetase in Blastocystis: The Emerging Role of Gatekeeper Residues.

    PubMed

    Vashisht, Kapil; Verma, Sonia; Gupta, Sunita; Lynn, Andrew M; Dixit, Rajnikant; Mishra, Neelima; Valecha, Neena; Hamblin, Karleigh A; Maytum, Robin; Pandey, Kailash C; van der Giezen, Mark

    2017-01-24

    Charged, solvent-exposed residues at the entrance to the substrate binding site (gatekeeper residues) produce electrostatic dipole interactions with approaching substrates, and control their access by a novel mechanism called "electrostatic gatekeeper effect". This proof-of-concept study demonstrates that the nucleotide specificity can be engineered by altering the electrostatic properties of the gatekeeper residues outside the binding site. Using Blastocystis succinyl-CoA synthetase (SCS, EC 6.2.1.5), we demonstrated that the gatekeeper mutant (ED) resulted in ATP-specific SCS to show high GTP specificity. Moreover, nucleotide binding site mutant (LF) had no effect on GTP specificity and remained ATP-specific. However, via combination of the gatekeeper mutant with the nucleotide binding site mutant (ED+LF), a complete reversal of nucleotide specificity was obtained with GTP, but no detectable activity was obtained with ATP. This striking result of the combined mutant (ED+LF) was due to two changes; negatively charged gatekeeper residues (ED) favored GTP access, and nucleotide binding site residues (LF) altered ATP binding, which was consistent with the hypothesis of the "electrostatic gatekeeper effect". These results were further supported by molecular modeling and simulation studies. Hence, it is imperative to extend the strategy of the gatekeeper effect in a different range of crucial enzymes (synthetases, kinases, and transferases) to engineer substrate specificity for various industrial applications and substrate-based drug design.

  8. Teaching and Assessing ED Handoffs: A Qualitative Study Exploring Resident, Attending, and Nurse Perceptions.

    PubMed

    Flanigan, Moira; Heilman, James A; Johnson, Tom; Yarris, Lalena M

    2015-11-01

    The Accreditation Council for Graduate Medical Education requires that residency programs ensure resident competency in performing safe, effective handoffs. Understanding resident, attending, and nurse perceptions of the key elements of a safe and effective emergency department (ED) handoff is a crucial step to developing feasible, acceptable educational interventions to teach and assess this fundamental competency. The aim of our study was to identify the essential themes of ED-based handoffs and to explore the key cultural and interprofessional themes that may be barriers to developing and implementing successful ED-based educational handoff interventions. Using a grounded theory approach and constructivist/interpretivist research paradigm, we analyzed data from three primary and one confirmatory focus groups (FGs) at an urban, academic ED. FG protocols were developed using open-ended questions that sought to understand what participants felt were the crucial elements of ED handoffs. ED residents, attendings, a physician assistant, and nurses participated in the FGs. FGs were observed, hand-transcribed, audio-recorded and subsequently transcribed. We analyzed data using an iterative process of theme and subtheme identification. Saturation was reached during the third FG, and the fourth confirmatory group reinforced the identified themes. Two team members analyzed the transcripts separately and identified the same major themes. ED providers identified that crucial elements of ED handoff include the following: 1) Culture (provider buy-in, openness to change, shared expectations of sign-out goals); 2) Time (brevity, interruptions, waiting); 3) Environment (physical location, ED factors); 4) Process (standardization, information order, tools). Key participants in the ED handoff process perceive that the crucial elements of intershift handoffs involve the themes of culture, time, environment, and process. Attention to these themes may improve the feasibility and acceptance of educational interventions that aim to teach and assess handoff competency.

  9. Solvent replacement for green processing.

    PubMed Central

    Sherman, J; Chin, B; Huibers, P D; Garcia-Valls, R; Hatton, T A

    1998-01-01

    The implementation of the Montreal Protocol, the Clean Air Act, and the Pollution Prevention Act of 1990 has resulted in increased awareness of organic solvent use in chemical processing. The advances made in the search to find "green" replacements for traditional solvents are reviewed, with reference to solvent alternatives for cleaning, coatings, and chemical reaction and separation processes. The development of solvent databases and computational methods that aid in the selection and/or design of feasible or optimal environmentally benign solvent alternatives for specific applications is also discussed. Images Figure 2 Figure 3 PMID:9539018

  10. DOD Hotline Allegations on Army Use of A Computer Contract

    DTIC Science & Technology

    1993-10-29

    Army, the Navy, and the Defense Logistics Agency central order processing offices and reviewed delivery orders issued on the EDS contract. A...o The contracting officers used the EDS contract line item number and the description when completing a delivery order. o The central order ... processing offices used an automated data base system to match contract line item numbers from the delivery orders to the EDS contract. o EDS verified that

  11. Thermal degradation of the solvent employed in the next-generation caustic-side solvent extraction process and its effect on the extraction, scrubbing, and stripping of cesium

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Roach, Benjamin D.; Williams, Neil J.; Moyer, Bruce A.

    As part of the ongoing development of the Next-Generation Caustic-Side Solvent Extraction (NGS) process, the thermal stability of the process solvent was investigated and shown to be adequate for industrial application. The solvent was thermally treated at 35 C over a period of 13 months whilst in dynamic contact with each of the aqueous phases of the current NGS process, namely SRS 15 (a highly caustic waste simulant), sodium hydroxide scrub solution (0.025 M), and boric acid strip solution (0.01 M). The effect of thermal treatment was evaluated by assessing batch extract/scrub/strip performance as a function of time, by monitoringmore » the sodium extraction capacity of the solvent, and by analysis of the solvent using electrospray mass spectrometry. Current studies indicate that the NGS solvent should be thermally robust for a period of XXX months at the Modular Caustic-Side Solvent Extraction Unit (MCU) pilot plant located at Savannah River Site. Furthermore, the guanidine suppressor appears to be the solvent component most significantly impacted by thermal treatment of the solvent, showing significant degradation over time.« less

  12. Thermal degradation of the solvent employed in the next-generation caustic-side solvent extraction process and its effect on the extraction, scrubbing, and stripping of cesium

    DOE PAGES

    Roach, Benjamin D.; Williams, Neil J.; Moyer, Bruce A.

    2015-09-02

    As part of the ongoing development of the Next-Generation Caustic-Side Solvent Extraction (NGS) process, the thermal stability of the process solvent was investigated and shown to be adequate for industrial application. The solvent was thermally treated at 35 C over a period of 13 months whilst in dynamic contact with each of the aqueous phases of the current NGS process, namely SRS 15 (a highly caustic waste simulant), sodium hydroxide scrub solution (0.025 M), and boric acid strip solution (0.01 M). The effect of thermal treatment was evaluated by assessing batch extract/scrub/strip performance as a function of time, by monitoringmore » the sodium extraction capacity of the solvent, and by analysis of the solvent using electrospray mass spectrometry. Current studies indicate that the NGS solvent should be thermally robust for a period of XXX months at the Modular Caustic-Side Solvent Extraction Unit (MCU) pilot plant located at Savannah River Site. Furthermore, the guanidine suppressor appears to be the solvent component most significantly impacted by thermal treatment of the solvent, showing significant degradation over time.« less

  13. Marketing and public relations in the emergency department.

    PubMed

    Mayer, T A; Tilson, W; Hemingway, J

    1987-02-01

    This article outlines the elements of successful ED marketing, as well as providing definitions for terms used within the marketing process. In today's competition and rapidly changing environment, marketing and public relations are tools that every ED Medical Director may want to consider. Because the marketing process requires a great deal of time and effort, as well as a high degree of intellectual honesty, it should never be entered into without a strong commitment. However, marketing the ED can be among the most productive, stimulating, and gratifying experiences for the ED Medical Director, the emergency department physicians, and all ED service personnel.

  14. Unusual seeding mechanism for enhanced performance in solid-phase magnetic extraction of Rare Earth Elements

    PubMed Central

    Polido Legaria, Elizabeth; Rocha, Joao; Tai, Cheuk-Wai; Kessler, Vadim G.; Seisenbaeva, Gulaim A.

    2017-01-01

    Due to the increasing demand of Rare Earth Elements (REE or RE), new and more efficient techniques for their extraction are necessary, suitable for both mining and recycling processes. Current techniques such as solvent extraction or solid adsorbents entail drawbacks such as using big volumes of harmful solvents or limited capacity. Hybrid nanoadsorbents based on SiO2 and highly stable γ-Fe2O3-SiO2 nanoparticles, proved recently to be very attractive for adsorption of REE, yet not being the absolute key to solve the problem. In the present work, we introduce a highly appealing new approach in which the nanoparticles, rather than behaving as adsorbent materials, perform as inducers of crystallization for the REE in the form of hydroxides, allowing their facile and practically total removal from solution. This induced crystallization is achieved by tuning the pH, offering an uptake efficiency more than 20 times higher than previously reported (up to 900 mg RE3+/g vs. 40 mg RE3+/g). The obtained phases were characterized by SEM-EDS, TEM, STEM and EFTEM and 13C and 29Si solid state NMR. Magnetic studies showed that the materials possessed enough magnetic properties to be easily removed by a magnet, opening ways for an efficient and industrially applicable separation technique. PMID:28266566

  15. Unusual seeding mechanism for enhanced performance in solid-phase magnetic extraction of Rare Earth Elements

    NASA Astrophysics Data System (ADS)

    Polido Legaria, Elizabeth; Rocha, Joao; Tai, Cheuk-Wai; Kessler, Vadim G.; Seisenbaeva, Gulaim A.

    2017-03-01

    Due to the increasing demand of Rare Earth Elements (REE or RE), new and more efficient techniques for their extraction are necessary, suitable for both mining and recycling processes. Current techniques such as solvent extraction or solid adsorbents entail drawbacks such as using big volumes of harmful solvents or limited capacity. Hybrid nanoadsorbents based on SiO2 and highly stable γ-Fe2O3-SiO2 nanoparticles, proved recently to be very attractive for adsorption of REE, yet not being the absolute key to solve the problem. In the present work, we introduce a highly appealing new approach in which the nanoparticles, rather than behaving as adsorbent materials, perform as inducers of crystallization for the REE in the form of hydroxides, allowing their facile and practically total removal from solution. This induced crystallization is achieved by tuning the pH, offering an uptake efficiency more than 20 times higher than previously reported (up to 900 mg RE3+/g vs. 40 mg RE3+/g). The obtained phases were characterized by SEM-EDS, TEM, STEM and EFTEM and 13C and 29Si solid state NMR. Magnetic studies showed that the materials possessed enough magnetic properties to be easily removed by a magnet, opening ways for an efficient and industrially applicable separation technique.

  16. Load Balancing at Emergency Departments using ‘Crowdinforming’

    PubMed Central

    Friesen, Marcia R; Strome, Trevor; Mukhi, Shamir; McLoed, Robert

    2011-01-01

    Background: Emergency Department (ED) overcrowding is an important healthcare issue facing increasing public and regulatory scrutiny in Canada and around the world. Many approaches to alleviate excessive waiting times and lengths of stay have been studied. In theory, optimal ED patient flow may be assisted via balancing patient loads between EDs (in essence spreading patients more evenly throughout this system). This investigation utilizes simulation to explore “Crowdinforming” as a basis for a process control strategy aimed to balance patient loads between six EDs within a mid-sized Canadian city. Methods: Anonymous patient visit data comprising 120,000 ED patient visits over six months to six ED facilities were obtained from the region’s Emergency Department Information System (EDIS) to (1) determine trends in ED visits and interactions between parameters; (2) to develop a process control strategy integrating crowdinforming; and, (3) apply and evaluate the model in a simulated environment to explore the potential impact on patient self-redirection and load balancing between EDs. Results: As in reality, the data available and subsequent model demonstrated that there are many factors that impact ED patient flow. Initial results suggest that for this particular data set used, ED arrival rates were the most useful metric for ED ‘busyness’ in a process control strategy, and that Emergency Department performance may benefit from load balancing efforts. Conclusions: The simulation supports the use of crowdinforming as a potential tool when used in a process control strategy to balance the patient loads between EDs. The work also revealed that the value of several parameters intuitively expected to be meaningful metrics of ED ‘busyness’ was not evident, highlighting the importance of finding parameters meaningful within one’s particular data set. The information provided in the crowdinforming model is already available in a local context at some ED sites. The extension to a wider dissemination of information via an Internet web service accessible by smart phones is readily achievable and not a technological obstacle. Similarly, the system could be extended to help direct patients by including future estimates or predictions in the crowdinformed data. The contribution of the simulation is to allow for effective policy evaluation to better inform the public of ED ‘busyness’ as part of their decision making process in attending an emergency department. In effect, this is a means of providing additional decision support insights garnered from a simulation, prior to a real world implementation. PMID:23569610

  17. Alternative Green Solvents Project

    NASA Technical Reports Server (NTRS)

    Maloney, Phillip R.

    2012-01-01

    Necessary for safe and proper functioning of equipment. Mainly halogenated solvents. Tetrachloride, Trichloroethylene (TCE), CFC-113. No longer used due to regulatory/safety concerns. Precision Cleaning at KSC: Small % of total parts. Used for liquid oxygen (LOX) systems. Dual solvent process. Vertrel MCA (decafluoropentane (DFP) and trons-dichloroethylene) HFE-7100. DFP has long term environmental concerns. Project Goals: a) Identify potential replacements. b) 22 wet chemical processes. c) 3 alternative processes. d) Develop test procedures. e) Contamination and cleaning. f) Analysis. g) Use results to recommend alternative processes. Conclusions: a) No alternative matched Vertrel in this study. b) No clear second place solvent. c) Hydrocarbons- easy; Fluorinated greases- difficult. d) Fluorinated component may be needed in replacement solvent. e) Process may need to make up for shortcoming of the solvent. f) Plasma and SCC02 warrant further testing.

  18. Catalytic coal liquefaction with treated solvent and SRC recycle

    DOEpatents

    Garg, Diwakar; Givens, Edwin N.; Schweighardt, Frank K.

    1986-01-01

    A process for the solvent refining of coal to distillable, pentane soluble products using a dephenolated and denitrogenated recycle solvent and a recycled, pentane-insoluble, solvent-refined coal material, which process provides enhanced oil-make in the conversion of coal.

  19. ORNL engineering design and construction reengineering report

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    McNeese, L.E.

    1998-01-01

    A team composed of individuals representing research and development (R and D) divisions, infrastructure support organizations, and Department of Energy (DOE)-Oak Ridge Operations was chartered to reengineer the engineering, design, and construction (ED and C) process at Oak Ridge National Laboratory (ORNL). The team recognized that ED and C needs of both R and D customers and the ORNL infrastructure program have to be met to maintain a viable and competitive national laboratory. Their goal was to identify and recommend implementable best-in-class ED and C processes that will efficiently and cost-effectively support the ORNL R and D staff by beingmore » responsive to their programmatic and infrastructure needs. The team conducted process mapping of current and potential ED and C approaches, developed idealized versions of ED and C processes, and identified potential barriers to an efficient ED and C process. Eight subteams were assigned to gather information and to evaluate the significance of potential barriers through benchmarking, surveys, interviews, and reviews of key topical areas in order to determine whether the perceived barriers were real and important and whether they resulted from laws or regulations over which ORNL has no control.« less

  20. Achieving over 9.8% Efficiency in Nonfullerene Polymer Solar Cells by Environmentally Friendly Solvent Processing.

    PubMed

    Wu, Yue; Zou, Yan; Yang, Hang; Li, Yaowen; Li, Hongkun; Cui, Chaohua; Li, Yongfang

    2017-10-25

    Nowadays, most of the solution-processed high-efficiency polymer solar cell (PSC) devices are fabricated by halogenated solvents (such as chlorobenzene, 1,2-dichlorobenzene, chloroform, etc.) which are harmful to people and the environment. Therefore, it is essential to develop high-efficiency PSC devices processed by environmentally friendly solvent processing for their industrialization. In this regard, we report a new alkylthio chain-based conjugated polymer PBDB-TS as donor material for environmentally friendly solvent-processed PSCs. PBDB-TS possesses a low-lying HOMO energy level at -5.42 eV and a good solubility in toluene and o-xylene. By using o-xylene and 1% N-methylpyrrolidone as processing solvent, following by the thermal annealing treatment for PBDB-TS:ITIC blend films, well-developed morphological features, and balanced charge transport properties are observed, leading to a high power conversion efficiency (PCE) of 9.85%, higher than that of the device cast from halogenated solvent (PCE = 9.65%). The results suggest that PBDB-TS is an attractive donor material for nonhalogen solvents-processing PSCs.

  1. Study on the disparate transition behaviors of the electrical/physical properties in PEDOT:PSS film depending on solvent species under a follow-up solution-treatment process

    NASA Astrophysics Data System (ADS)

    Yun, Dong-Jin; Kim, Jung-Hwa; Kim, Seong Heon; Seol, Minsu; Yu, DaEun; Kwon, Hyukju; Ham, Yongnam; Chung, JaeGwan; Kim, Yongsu; Heo, Sung

    2016-04-01

    In most solution-processed organic devices, a poly(3,4-ethylenedioxythiophene) (PEDOT) polymerized with poly(4-styrenesulfonate) (PSS) film is inevitably affected by various conditions during the subsequent solution-coating processes. To investigate the effects of direct solvent exposure on the properties of PEDOT polymerized with PSS (PEDOT:PSS) films, photoemission spectroscopy-based analytical methods were used before and after solvent-coating processes. Our results clearly indicate that PEDOT:PSS films undergo a different transition mechanism depending on the solubility of the solvent in water. The water-miscible solvents induce the solvation of hydrophilic PSS chains. As a result, this process allows the solvent to diffuse into the PEDOT:PSS film, and a conformational change between PEDOT and PSS occurs. On the other hand, the water-immiscible organic solvents cause the partial adsorption of solvent molecules at the PE surface, which leads to changes in the surface properties, including work function. Based on our finding, we demonstrate that the energy-level alignments at the organic semiconductor/electrode interface for the PEDOT:PSS films can be controlled by simple solvent treatments.

  2. Emergency Department Utilization Report to Decrease Visits by Pediatric Gastroenterology Patients.

    PubMed

    Lee, Jarone; Greenspan, Peter T; Israel, Esther; Katz, Aubrey; Fasano, Alessio; Kaafarani, Haytham M A; Linov, Pamela L; Raja, Ali S; Rao, Sandhya K

    2016-07-01

    Emergency department (ED) utilization is a major driver of health care costs. Specialist physicians have an important role in addressing ED utilization, especially at highly specialized, academic medical centers. We sought to investigate whether reporting of ED utilization to specialist physicians can decrease ED visits. This study analyzed an intervention to reduce ED utilization among ED patients who were followed by pediatric gastroenterologists. In May 2013, each pediatric gastroenterologist began receiving reports with rates of ED use by their patients. The reports generated discussion that resulted in a cultural and process change in which patients with urgent gastrointestinal (GI)-related complaints were preferentially seen in the office. Using control charts, we examined GI-related and all-diagnoses ED use over a 2-year period. The rate of GI-related ED visits decreased by 60% after the intervention, from 4.89 to 1.95 per 1000 office visits (P < .001). Similarly, rates of GI-related ED visits during office hours decreased by 59% from 2.19 to 0.89 per 1000 (P < .001). Rates of all-diagnoses ED visits did not change. Physician-level reporting of ED utilization to pediatric gastroenterologists was associated with physician engagement and a cultural and process change to preferentially treat patients with urgent issues in the office. Copyright © 2016 by the American Academy of Pediatrics.

  3. Compressed air-assisted solvent extraction (CASX) for metal removal.

    PubMed

    Li, Chi-Wang; Chen, Yi-Ming; Hsiao, Shin-Tien

    2008-03-01

    A novel process, compressed air-assisted solvent extraction (CASX), was developed to generate micro-sized solvent-coated air bubbles (MSAB) for metal extraction. Through pressurization of solvent with compressed air followed by releasing air-oversaturated solvent into metal-containing wastewater, MSAB were generated instantaneously. The enormous surface area of MSAB makes extraction process extremely fast and achieves very high aqueous/solvent weight ratio (A/S ratio). CASX process completely removed Cr(VI) from acidic electroplating wastewater under A/S ratio of 115 and extraction time of less than 10s. When synthetic wastewater containing Cd(II) of 50mgl(-1) was treated, A/S ratios of higher than 714 and 1190 could be achieved using solvent with extractant/diluent weight ratio of 1:1 and 5:1, respectively. Also, MSAB have very different physical properties, such as size and density, compared to the emulsified solvent droplets, making separation and recovery of solvent from treated effluent very easy.

  4. Aminosilicone solvent recovery methods and systems

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Spiry, Irina Pavlovna; Perry, Robert James; Wood, Benjamin Rue

    The present invention is directed to aminosilicone solvent recovery methods and systems. The methods and systems disclosed herein may be used to recover aminosilicone solvent from a carbon dioxide containing vapor stream, for example, a vapor stream that leaves an aminosilicone solvent desorber apparatus. The methods and systems of the invention utilize a first condensation process at a temperature from about 80.degree. C. to about 150.degree. C. and a second condensation process at a temperature from about 5.degree. C. to about 75.degree. C. The first condensation process yields recovered aminosilicone solvent. The second condensation process yields water.

  5. Coal liquefaction process

    DOEpatents

    Skinner, Ronald W.; Tao, John C.; Znaimer, Samuel

    1985-01-01

    This invention relates to an improved process for the production of liquid carbonaceous fuels and solvents from carbonaceous solid fuels, especially coal. The claimed improved process includes the hydrocracking of the light SRC mixed with a suitable hydrocracker solvent. The recycle of the resulting hydrocracked product, after separation and distillation, is used to produce a solvent for the hydrocracking of the light solvent refined coal.

  6. Catalytic coal liquefaction with treated solvent and SRC recycle

    DOEpatents

    Garg, D.; Givens, E.N.; Schweighardt, F.K.

    1986-12-09

    A process is described for the solvent refining of coal to distillable, pentane soluble products using a dephenolated and denitrogenated recycle solvent and a recycled, pentane-insoluble, solvent-refined coal material, which process provides enhanced oil-make in the conversion of coal. 2 figs.

  7. SOLVENT EXTRACTION PROCESS

    DOEpatents

    Jonke, A.A.

    1957-10-01

    In improved solvent extraction process is described for the extraction of metal values from highly dilute aqueous solutions. The process comprises contacting an aqueous solution with an organic substantially water-immiscible solvent, whereby metal values are taken up by a solvent extract phase; scrubbing the solvent extract phase with an aqueous scrubbing solution; separating an aqueous solution from the scrubbed solvent extract phase; and contacting the scrubbed solvent phase with an aqueous medium whereby the extracted metal values are removed from the solvent phase and taken up by said medium to form a strip solution containing said metal values, the aqueous scrubbing solution being a mixture of strip solution and an aqueous solution which contains mineral acids anions and is free of the metal values. The process is particularly effective for purifying uranium, where one starts with impure aqueous uranyl nitrate, extracts with tributyl phosphate dissolved in carbon tetrachloride, scrubs with aqueous nitric acid and employs water to strip the uranium from the scrubbed organic phase.

  8. Processing Solvent Dependent Morphology of Diketopyrrolopyrrole (DPP) based Low Band Gap Polymer and PCBM Blends

    NASA Astrophysics Data System (ADS)

    Ferdous, Sunzida; Liu, Feng; Russell, Thomas

    2013-03-01

    Solution processing of polymer semiconductors is widely used for fabrication of low cost organic solar cells. Recently, mixed solvent systems or additive based systems for fabricating polymer solar cells have proven to be beneficial for obtaining high performance devices with multi-length scale morphologies. To control the morphology during the processing step, one needs to understand the effect of solvent as it evaporates to form the final thin film structure. In this study, we used diketopyrrolopyrrole (DPP) based low band gap polymer and phenyl-C71-butyric acid methyl ester (PCBM) blend in a series of mixed solvent systems consisting of a good solvent for both of the active material components, as well as different solvents that are good solvents for PCBM, but poor solvents for the polymer. Different evaporation times of the poor solvents during the drying process, and different solubility of the polymer in these poor solvents as well as their interaction with the substrate play an important role in the final morphology. In-situ GIWAXS studies were performed to observe the evolution of the structure as the solvent evaporates. The final morphologies of the thin film devices were also characterized by AFM, TEM, and various x-ray scattering techniques to correlate the morphology with the obtained device performances.

  9. Separation of Gadolinium (Gd) using Synergic Solvent Mixed Topo-D2EHPA with Extraction Method.

    NASA Astrophysics Data System (ADS)

    Effendy, N.; Basuki, K. T.; Biyantoro, D.; Perwira, N. K.

    2018-04-01

    The main problem to obtain Gd with high purity is the similarity of chemical properties and physical properties with the other rare earth elements (REE) such as Y and Dy, it is necessary to do separation by the extraction process. The purpose of this research to determine the best solvent type, amount of solvent, feed and solvent ratio in the Gd extraction process, to determine the rate order and the value of the rate constant of Gd concentration based on experimental data of aqueous phase concentration as a function of time and to know the effect of temperature on the reaction speed constant. This research was conducted on variation of solvent, amount of solvent, feed and solvent ratio in the extraction process of Gd separation, extraction time to determine the order value and the rate constant of Gd concentration in extraction process based on the aqueous phase concentration data as a function of time, to the rate constant of decreasing concentration of Gd. Based on the calculation results, the solvent composition was obtained with the best feed to separate the rare earth elements Gd in the extraction process is 1 : 4 with 15% concentration of TOPO and 10% concentration of D2EHPA. The separation process of Gd using extraction method by solvent TOPO-D2EHPA 2 : 1 comparison is better than single solvent D2EHPA / TOPO because of the synergistic effect. The rate order of separation process of Gd follows order 1. The Arrhenius Gd equation becomes k = 1.46 x 10-7 exp (-6.96 kcal / mol / RT).

  10. Organic solvents in the pharmaceutical industry.

    PubMed

    Grodowska, Katarzyna; Parczewski, Andrzej

    2010-01-01

    Organic solvents are commonly used in the pharmaceutical industry as reaction media, in separation and purification of synthesis products and also for cleaning of equipment. This paper presents some aspects of organic solvents utilization in an active pharmaceutical ingredient and a drug product manufacturing process. As residual solvents are not desirable substances in a final product, different methods for their removal may be used, provided they fulfill safety criteria. After the drying process, analyses need to be performed to check if amounts of solvents used at any step of the production do not exceed acceptable limits (taken from ICH Guideline or from pharmacopoeias). Also new solvents like supercritical fluids or ionic liquids are developed to replace "traditional" organic solvents in the pharmaceutical production processes.

  11. Patient-Centered Care Transition for Patients Admitted through the ED: Improving Patient and Employee Experience

    PubMed Central

    Algauer, Andrea; Rivera, Stephanie; Faurote, Robert

    2015-01-01

    With increasing wait times in emergency departments (ED) across America, there is a need to streamline the inpatient admission process in order to decrease wait times and more important, to increase patient and employee satisfaction. One inpatient unit at New York-Presbyterian Weill Cornell Medical Center initiated a program to help expedite the inpatient admission process from the ED. The goal of the ED Bridge program is to ease the patient's transition from the ED to an inpatient unit by visiting the patient in the ED and introducing and setting expectations for the inpatient environment (i.e. telemetry alarms, roommates, hourly comfort rounds). Along with improving the patient experience, this program intends to improve the collaboration between ED nurses and inpatient nurses. With the continued support of our nurse management, hospital administrators and most important, our staff, this concept is aimed to increase patient satisfaction scores and subsequently employee satisfaction. PMID:28725813

  12. Solvents and sustainable chemistry

    PubMed Central

    Welton, Tom

    2015-01-01

    Solvents are widely recognized to be of great environmental concern. The reduction of their use is one of the most important aims of green chemistry. In addition to this, the appropriate selection of solvent for a process can greatly improve the sustainability of a chemical production process. There has also been extensive research into the application of so-called green solvents, such as ionic liquids and supercritical fluids. However, most examples of solvent technologies that give improved sustainability come from the application of well-established solvents. It is also apparent that the successful implementation of environmentally sustainable processes must be accompanied by improvements in commercial performance. PMID:26730217

  13. New 'patent accelerated care environment' aims to facilitate work flow, free up ED for acute care needs.

    PubMed

    2012-02-01

    Faced with rising acuity levels and surging demand, Virginia Mason Medical Center modified the Clinical Decision Unit concept used in many EDs, and developed a new Patient Accelerated Care Environment (PACE) to care for observation patients, process patients for discharge, and to prepare patients for admission.The approach is designed to utilize ED beds for initial processing of patients, allowing resuscitative care if needed, and treating and releasing the patients with quick care needs. Using the Virginia Mason Production System, a methodology that is modeled after Toyota production techniques, developers designed an optimal work flow pattern and then built infrastructure to facilitate that process. All patients who present to the ED for care are seen by the ED team through a "team greet" approach. Approximately 35% to 40% of patients who come to the ED for care are transferred to the PACE unit. Patients assigned to the PACE unit typically remain there for 4 to 48 hours, depending on their care needs.

  14. PROCESS OF SEPARATING URANIUM FROM AQUEOUS SOLUTION BY SOLVENT EXTRACTION

    DOEpatents

    Warf, J.C.

    1958-08-19

    A process is described for separating uranium values from aqueous uranyl nitrate solutions. The process consists in contacting the uramium bearing solution with an organic solvent, tributyl phosphate, preferably diluted with a less viscous organic liquida whereby the uranyl nitrate is extracted into the organic solvent phase. The uranvl nitrate may be recovered from the solvent phase bv back extracting with an aqueous mediuin.

  15. Occupational trichloroethylene hypersensitivity syndrome: human herpesvirus 6 reactivation and rash phenotypes.

    PubMed

    Kamijima, Michihiro; Wang, Hailan; Yamanoshita, Osamu; Ito, Yuki; Xia, Lihua; Yanagiba, Yukie; Chen, Cishan; Okamura, Ai; Huang, Zhenlie; Qiu, Xinxiang; Song, Xiangrong; Cai, Tingfeng; Liu, Lili; Ge, Yichen; Deng, Yingyu; Naito, Hisao; Yoshikawa, Tetsushi; Tohyama, Mikiko; Li, Laiyu; Huang, Hanlin; Nakajima, Tamie

    2013-12-01

    Trichloroethylene (TCE) is an industrial solvent which can cause severe generalized dermatitis, i.e., occupational TCE hypersensitivity syndrome. Reactivation of latent human herpesvirus 6 (HHV6) can occur in such patients, which has made TCE known as a causative chemical of drug-induced hypersensitivity syndrome (DIHS). This study aimed to clarify HHV6 status, cytokine profiles and their association with rash phenotypes in patients with TCE hypersensitivity syndrome. HHV6 DNA copy numbers, anti-HHV6 antibody titers, and cytokines were measured in blood prospectively sampled 5-7 times from 28 hospitalized patients with the disease. The patients (19 had exfoliative dermatitis (ED) and 9 had non-ED type rash) generally met the diagnostic criteria for DIHS. Viral reactivation defined as increases in either HHV6 DNA (≥100 genomic copies/10(6) peripheral blood mononuclear cells) or antibody titers was identified in 24 (89%) patients. HHV6 DNA, tumor necrosis factor (TNF)-α, interferon (IFN)-γ, interleukin (IL)-5, IL-6 and IL-10 concentrations were remarkably higher in the patients than in the healthy workers (p<0.01). Positive correlations between HHV6 DNA, TNF-α, IFN-γ, IL-6 and IL-10 were significant (p<0.05) except for that between HHV6 DNA and IFN-γ. An increase in HHV6 DNA was positively associated with an increase in TNF-α on admission (p<0.01). HHV6 DNA, the antibody titers, TNF-α and IL-10 concentrations were significantly higher in ED than in the non-ED type (p<0.05). Reactivated HHV6 and the increased cytokines could be biomarkers of TCE hypersensitivity syndrome. The higher-level reactivation and stronger humoral responses were associated with ED-type rash. Copyright © 2013 Japanese Society for Investigative Dermatology. Published by Elsevier Ireland Ltd. All rights reserved.

  16. Process and apparatus for solvent extraction of oil from oil-containing diatomite ore

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Karnofsky, G. B.

    1980-12-16

    A process for solvent extraction of oil from oil bearing diatomite ore and an apparatus for use therewith, wherein the ore is extracted by countercurrent decantation with a hydrocarbon solvent, solvent is recovered from the extract by multiple effect evaporation followed by stripping, and the spent diatomite is contacted with water to displace a major portion of the solvent therefrom, and solvent is recovered from the aqueous slurry of the spent diatomite by stripping with steam at superatmospheric pressure.

  17. Batch extracting process using magneticparticle held solvents

    DOEpatents

    Nunez, Luis; Vandergrift, George F.

    1995-01-01

    A process for selectively removing metal values which may include catalytic values from a mixture containing same, wherein a magnetic particle is contacted with a liquid solvent which selectively dissolves the metal values to absorb the liquid solvent onto the magnetic particle. Thereafter the solvent-containing magnetic particles are contacted with a mixture containing the heavy metal values to transfer metal values into the solvent carried by the magnetic particles, and then magnetically separating the magnetic particles. Ion exchange resins may be used for selective solvents.

  18. Interprofessional communication supporting clinical handover in emergency departments: An observation study.

    PubMed

    Redley, Bernice; Botti, Mari; Wood, Beverley; Bucknall, Tracey

    2017-08-01

    Poor interprofessional communication poses a risk to patient safety at change-of-shift in emergency departments (EDs). The purpose of this study was to identify and describe patterns and processes of interprofessional communication impacting quality of ED change-of-shift handovers. Observation of 66 change-of-shift handovers at two acute hospital EDs in Victoria, Australia. Focus groups with 34 nurse participants complemented the observations. Qualitative data analysis involved content and thematic methods. Four structural components of ED handover processes emerged represented by (ABCD): (1) Antecedents; (2) Behaviours and interactions; (3) Content; and (4) Delegation of ongoing care. Infrequent and ad hoc interprofessional communication and discipline-specific handover content and processes emerged as specific risks to patient safety at change-of-shift handovers. Three themes related to risky and effective practices to support interprofessional communications across the four stages of ED handovers emerged: 1) standard processes and practices, 2) teamwork and interactions and 3) communication activities and practices. Unreliable interprofessional communication can impact the quality of change-of-shift handovers in EDs and poses risk to patient safety. Structured reflective analysis of existing practices can identify opportunities for standardisation, enhanced team practices and effective communication across four stages of the handover process to support clinicians to enhance local handover practices. Future research should test and refine models to support analysis of practice, and identify and test strategies to enhance ED interprofessional communication to support clinical handovers. Copyright © 2017 College of Emergency Nursing Australasia. Published by Elsevier Ltd. All rights reserved.

  19. Next Generation Solvent Performance in the Modular Caustic Side Solvent Extraction Process - 15495

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Smith, Tara E.; Scherman, Carl; Martin, David

    Changes to the Modular Caustic Side Solvent Extraction Unit (MCU) flow-sheet were implemented in the facility. Implementation included changing the scrub and strip chemicals and concentrations, modifying the O/A ratios for the strip, scrub, and extraction contactor banks, and blending the current BoBCalixC6 extractant-based solvent in MCU with clean MaxCalix extractant-based solvent. During the successful demonstration period, the MCU process was subject to rigorous oversight to ensure hydraulic stability and chemical/radionuclide analysis of the key process tanks (caustic wash tank, solvent hold tank, strip effluent hold tank, and decontaminated salt solution hold tank) to evaluate solvent carryover to downstream facilitiesmore » and the effectiveness of cesium removal from the liquid salt waste. Results indicated the extraction of cesium was significantly more effective with an average Decontamination Factor (DF) of 1,129 (range was 107 to 1,824) and that stripping was effective. The contactor hydraulic performance was stable and satisfactory, as indicated by contactor vibration, contactor rotational speed, and flow stability; all of which remained at or near target values. Furthermore, the Solvent Hold Tank (SHT) level and specific gravity was as expected, indicating that solvent integrity and organic hydraulic stability were maintained. The coalescer performances were in the range of processing results under the BOBCalixC6 flow sheet, indicating negligible adverse impact of NGS deployment. After the Demonstration period, MCU began processing via routine operations. Results to date reiterate the enhanced cesium extraction and stripping capability of the Next Generation Solvent (NGS) flow sheet. This paper presents process performance results of the NGS Demonstration and continued operations of MCU utilizing the blended BobCalixC6-MaxCalix solvent under the NGS flowsheet.« less

  20. Green thermal-assisted synthesis and characterization of novel cellulose-Mg(OH)2 nanocomposite in PEG/NaOH solvent.

    PubMed

    Ponomarev, Nikolai; Repo, Eveliina; Srivastava, Varsha; Sillanpää, Mika

    2017-11-15

    Synthesis of nanocomposites was performed using microcrystalline cellulose (MCC), MgCl 2 in PEG/NaOH solvent by a thermal-assisted method at different temperatures by varying time and the amount of MCC. Results of XRD, FTIR, and EDS mapping showed that the materials consisted of only cellulose (CL) and magnesium hydroxide (MH). According to FTIR and XRD, it was found that crystallinity of MH in cellulose nanocomposites is increased with temperature and heating time and decreased with increasing of cellulose amount. The PEG/NaOH solvent has a significant effect on cellulose and Mg(OH) 2 morphology. BET and BJH results demonstrated the effects of temperature and cellulose amount on the pore size corresponding to mesoporous materials. TG and DTG analyses showed the increased thermal stability of cellulose nanocomposites with increasing temperature. TEM and SEM analyses showed an even distribution of MH nanostructures with various morphology in the cellulose matrix. The cellulose presented as the polymer matrix in the nanocomposites. It was supposed the possible interaction between cellulose and Mg(OH) 2 . The novel synthesis method used in this study is feasible, cost-efficient and environmentally friendly. Copyright © 2017 Elsevier Ltd. All rights reserved.

  1. 21 CFR 173.280 - Solvent extraction process for citric acid.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Solvent extraction process for citric acid. 173.280... extraction process for citric acid. A solvent extraction process for recovery of citric acid from conventional Aspergillus niger fermentation liquor may be safely used to produce food-grade citric acid in...

  2. Compendium of Technical Papers on the Reductive Dechlorination of Chlorinated Solvents.

    DTIC Science & Technology

    1997-08-01

    30), was added to cultures atarate of 20 pL (for in Thauer et al. (22) with temperature = 25 °C; pH = 7; HC0 3- = 70 supplement (E0),twas)added0to...Microbiology 49 (5): 1080-1083. Zeikus, J. G. 1977. "The biology of methanogenic bacteria." Bacteriology Reviews 41 (2): 514- 541. 17 APPLIED AND ENVIRONMENTAL...Tetrachloroethene transformation to bacteria, p. 469-586. In A. J. B. Zehnder (ed.), Biology of anaerobic micro- trichloroethene and cis-1,2-dichloroethene by

  3. Organic Solvent Effects in Biomass Conversion Reactions.

    PubMed

    Shuai, Li; Luterbacher, Jeremy

    2016-01-01

    Transforming lignocellulosic biomass into fuels and chemicals has been intensely studied in recent years. A large amount of work has been dedicated to finding suitable solvent systems, which can improve the transformation of biomass into value-added chemicals. These efforts have been undertaken based on numerous research results that have shown that organic solvents can improve both conversion and selectivity of biomass to platform molecules. We present an overview of these organic solvent effects, which are harnessed in biomass conversion processes, including conversion of biomass to sugars, conversion of sugars to furanic compounds, and production of lignin monomers. A special emphasis is placed on comparing the solvent effects on conversion and product selectivity in water with those in organic solvents while discussing the origins of the differences that arise. We have categorized results as benefiting from two major types of effects: solvent effects on solubility of biomass components including cellulose and lignin and solvent effects on chemical thermodynamics including those affecting reactants, intermediates, products, and/or catalysts. Finally, the challenges of using organic solvents in industrial processes are discussed from the perspective of solvent cost, solvent stability, and solvent safety. We suggest that a holistic view of solvent effects, the mechanistic elucidation of these effects, and the careful consideration of the challenges associated with solvent use could assist researchers in choosing and designing improved solvent systems for targeted biomass conversion processes. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  4. Learning, Attention/Hyperactivity, and Conduct Problems as Sequelae of Excessive Daytime Sleepiness in a General Population Study of Young Children

    PubMed Central

    Calhoun, Susan L.; Fernandez-Mendoza, Julio; Vgontzas, Alexandros N.; Mayes, Susan D.; Tsaoussoglou, Marina; Rodriguez-Muñoz, Alfredo; Bixler, Edward O.

    2012-01-01

    Study Objectives: Although excessive daytime sleepiness (EDS) is a common problem in children, with estimates of 15%; few studies have investigated the sequelae of EDS in young children. We investigated the association of EDS with objective neurocognitive measures and parent reported learning, attention/hyperactivity, and conduct problems in a large general population sample of children. Design: Cross-sectional. Setting: Population based. Participants: 508 children from The Penn State Child Cohort. Interventions: N/A. Measurements and Results: Children underwent a 9-h polysomnogram, comprehensive neurocognitive testing, and parent rating scales. Children were divided into 2 groups: those with and without parent-reported EDS. Structural equation modeling was used to examine whether processing speed and working memory performance would mediate the relationship between EDS and learning, attention/hyperactivity, and conduct problems. Logistic regression models suggest that parent-reported learning, attention/hyperactivity, and conduct problems, as well as objective measurement of processing speed and working memory are significant sequelae of EDS, even when controlling for AHI and objective markers of sleep. Path analysis demonstrates that processing speed and working memory performance are strong mediators of the association of EDS with learning and attention/hyperactivity problems, while to a slightly lesser degree are mediators from EDS to conduct problems. Conclusions: This study suggests that in a large general population sample of young children, parent-reported EDS is associated with neurobehavioral (learning, attention/hyperactivity, conduct) problems and poorer performance in processing speed and working memory. Impairment due to EDS in daytime cognitive and behavioral functioning can have a significant impact on children's development. Citation: Calhoun SL; Fernandez-Mendoza J; Vgontzas AN; Mayes SD; Tsaoussoglou M; Rodriguez-Muñoz A; Bixler EO. Learning, attention/hyperactivity, and conduct problems as sequelae of excessive daytime sleepiness in a general population study of young children. SLEEP 2012;35(5):627-632. PMID:22547888

  5. Electrolytic conditioning of a magnesium aluminum chloride complex for reversible magnesium deposition

    DOE PAGES

    Barile, Christopher J.; Barile, Elizabeth C.; Zavadil, Kevin R.; ...

    2014-12-04

    We describe in this report the electrochemistry of Mg deposition and dissolution from the magnesium aluminum chloride complex (MACC). The results define the requirements for reversible Mg deposition and definitively establish that voltammetric cycling of the electrolyte significantly alters its composition and performance. Elemental analysis, scanning electron microscopy, and energy-dispersive X-ray spectroscopy (SEM-EDS) results demonstrate that irreversible Mg and Al deposits form during early cycles. Electrospray ionization-mass spectrometry (ESI-MS) data show that inhibitory oligomers develop in THF-based solutions. These oligomers form via the well-established mechanism of a cationic ring-opening polymerization of THF during the initial synthesis of the MACC andmore » under resting conditions. In contrast, MACC solutions in 1,2-dimethoxyethane (DME), an acyclic solvent, do not evolve as dramatically at open circuit potential. Furthermore, we propose a mechanism describing how the conditioning process of the MACC in THF improves its performance by both tuning the Mg:Al stoichiometry and eliminating oligomers.« less

  6. Spectroscopic and electrochemical characterization of some Schiff base metal complexes containing benzoin moiety

    NASA Astrophysics Data System (ADS)

    El-Shahawi, M. S.; Al-Jahdali, M. S.; Bashammakh, A. S.; Al-Sibaai, A. A.; Nassef, H. M.

    2013-09-01

    The ligation behavior of bis-benzoin ethylenediamine (B2ED) and benzoin thiosemicarbazone (BTS) Schiff bases towards Ru3+, Rh3+, Pd2+, Ni2+ and Cu2+ were determined. The bond length of M-N and spectrochemical parameters (10Dq, β, B and LFSE) of the complexes were evaluated. The redox characteristics of selected complexes were explored by cyclic voltammetry (CV) at Pt working electrode in non aqueous solvents. Au mesh (100 w/in.) optically transparent thin layer electrode (OTTLE) was also used for recording thin layer CV for selected Ru complex. Oxidation of some complexes occurs in a consecutive chemical reaction of an EC type mechanism. The characteristics of electron transfer process of the couples M2+/M3+ and M3+/M4+ (M = Ru3+, Rh3+) and the stability of the complexes towards oxidation and/or reduction were assigned. The nature of the electroactive species and reduction mechanism of selected electrode couples were assigned.

  7. Batch extracting process using magnetic particle held solvents

    DOEpatents

    Nunez, L.; Vandergrift, G.F.

    1995-11-21

    A process is described for selectively removing metal values which may include catalytic values from a mixture containing same, wherein a magnetic particle is contacted with a liquid solvent which selectively dissolves the metal values to absorb the liquid solvent onto the magnetic particle. Thereafter the solvent-containing magnetic particles are contacted with a mixture containing the heavy metal values to transfer metal values into the solvent carried by the magnetic particles, and then magnetically separating the magnetic particles. Ion exchange resins may be used for selective solvents. 5 figs.

  8. Process and apparatus for solvent extraction of oil from oil-containing diatomite ore

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Karnofsky, G.B.

    1979-09-11

    A process is described for solvent extraction of oil-bearing diatomite ore. An apparatus is provided for use therewith, wherein the ore is extracted by countercurrent decantation with a hydrocarbon solvent. The solvent is recovered from the extract by multiple effect evaporation followed by stripping, and the spent diatomite is contacted with water to displace a major portion of the solvent therefrom. The solvent is recovered from the aqueous slurry of the spent diatomite by stripping with steam at superatmospheric pressure. 17 claims.

  9. Introducing Products to DoD Using Specifications and Standards

    DTIC Science & Technology

    2011-08-18

    to utilize the Product Introduction Tool. Search ~Favorites .S » Links ~Customize Links ~ EDS-NMCI ~Free Hotmail Product Introduction Process User...the Product Introduction Tool. Search ~Favorites .S » Links ~Customize Links ~ EDS-NMCI ~Free Hotmail Product Introduction Process User Pol icy...Links i1 EDS-NMCI ~ Free Hotmail i] I] Go ldentitify Categories/Subcategories Identify the category/subcategory that most closely covers your

  10. Arabidopsis EDS1 connects pathogen effector recognition to cell compartment-specific immune responses.

    PubMed

    Heidrich, Katharina; Wirthmueller, Lennart; Tasset, Céline; Pouzet, Cécile; Deslandes, Laurent; Parker, Jane E

    2011-12-09

    Pathogen effectors are intercepted by plant intracellular nucleotide binding-leucine-rich repeat (NB-LRR) receptors. However, processes linking receptor activation to downstream defenses remain obscure. Nucleo-cytoplasmic basal resistance regulator EDS1 (ENHANCED DISEASE SUSCEPTIBILITY1) is indispensible for immunity mediated by TIR (Toll-interleukin-1 receptor)-NB-LRR receptors. We show that Arabidopsis EDS1 molecularly connects TIR-NB-LRR disease resistance protein RPS4 recognition of bacterial effector AvrRps4 to defense pathways. RPS4-EDS1 and AvrRps4-EDS1 complexes are detected inside nuclei of living tobacco cells after transient coexpression and in Arabidopsis soluble leaf extracts after resistance activation. Forced AvrRps4 localization to the host cytoplasm or nucleus reveals cell compartment-specific RPS4-EDS1 defense branches. Although nuclear processes restrict bacterial growth, programmed cell death and transcriptional resistance reinforcement require nucleo-cytoplasmic coordination. Thus, EDS1 behaves as an effector target and activated TIR-NB-LRR signal transducer for defenses across cell compartments.

  11. Decreasing troponin turnaround time in the emergency department using the central laboratory: A process improvement study.

    PubMed

    Boelstler, Arlene M; Rowland, Ralph; Theoret, Jennifer; Takla, Robert B; Szpunar, Susan; Patel, Shraddha P; Lowry, Andrew M; Pena, Margarita E

    2015-03-01

    To implement collaborative process improvement measures to reduce emergency department (ED) troponin turnaround time (TAT) to less than 60min using central laboratory. This was an observational, retrospective data study. A multidisciplinary team from the ED and laboratory identified opportunities and developed a new workflow model. Process changes were implemented in ED patient triage, staffing, lab collection and processing. Data collected included TAT of door-to-order, order-to-collect, collect-to-received, received-to-result, door-to-result, ED length of stay, and hemolysis rate before (January-August, 2011) and after (September 2011-June 2013) process improvement. After process improvement and implementation of the new workflow model, decreased median TAT (in min) was seen in door-to-order (54 [IQR43] vs. 11 [IQR20]), order-to-collect (15 [IQR 23] vs. 10 [IQR12]), collect-to-received (6 [IQR8] vs. 5 [IQR5]), received-to-result (30 [IQR12] vs. 24 [IQR11]), and overall door-to-result (117 [IQR60] vs. 60 [IQR40]). A troponin TAT of <60min was realized beginning in May 2012 (59 [IQR39]). Hemolysis rates decreased (14.63±0.74 vs. 3.36±1.99, p<0.0001), as did ED length of stay (5.87±2.73h vs. 5.15±2.34h, p<0.0001). Conclusion Troponin TAT of <60min using a central laboratory was achieved with collaboration between the ED and the laboratory; additional findings include a decreased ED length of stay. Copyright © 2014 The Canadian Society of Clinical Chemists. Published by Elsevier Inc. All rights reserved.

  12. The ED-inpatient dashboard: Uniting emergency and inpatient clinicians to improve the efficiency and quality of care for patients requiring emergency admission to hospital.

    PubMed

    Staib, Andrew; Sullivan, Clair; Jones, Matt; Griffin, Bronwyn; Bell, Anthony; Scott, Ian

    2017-06-01

    Patients who require emergency admission to hospital require complex care that can be fragmented, occurring in the ED, across the ED-inpatient interface (EDii) and subsequently, in their destination inpatient ward. Our hospital had poor process efficiency with slow transit times for patients requiring emergency care. ED clinicians alone were able to improve the processes and length of stay for the patients discharged directly from the ED. However, improving the efficiency of care for patients requiring emergency admission to true inpatient wards required collaboration with reluctant inpatient clinicians. The inpatient teams were uninterested in improving time-based measures of care in isolation, but they were motivated by improving patient outcomes. We developed a dashboard showing process measures such as 4 h rule compliance rate coupled with clinically important outcome measures such as inpatient mortality. The EDii dashboard helped unite both ED and inpatient teams in clinical redesign to improve both efficiencies of care and patient outcomes. © 2016 Australasian College for Emergency Medicine and Australasian Society for Emergency Medicine.

  13. Recovery of copper and water from copper-electroplating wastewater by the combination process of electrolysis and electrodialysis.

    PubMed

    Peng, Changsheng; Liu, Yanyan; Bi, Jingjing; Xu, Huizhen; Ahmed, Abou-Shady

    2011-05-30

    In this paper, a laboratory-scale process which combined electrolysis (EL) and electrodialysis (ED) was developed to treat copper-containing wastewater. The feasibility of such process for copper recovery as well as water reuse was determined. Effects of three operating parameters, voltage, initial Cu(2+) concentration and water flux on the recovery of copper and water were investigated and optimized. The results showed that about 82% of copper could be recovered from high concentration wastewater (HCW, >400mg/L) by EL, at the optimal conditions of voltage 2.5 V/cm and water flux 4 L/h; while 50% of diluted water could be recycled from low concentration wastewater (LCW, <200mg/L) by ED, at the optimal conditions of voltage 40 V and water flux 4 L/h. However, because of the limitation of energy consumption (EC), LCW for EL and HCW for ED could not be treated effectively, and the effluent water of EL and concentrated water of ED should be further treated before discharged. Therefore, the combination process of EL and ED was developed to realize the recovery of copper and water simultaneously from both HCW and LCW. The results of the EL-ED process showed that almost 99.5% of copper and 100% of water could be recovered, with the energy consumption of EL ≈ 3 kW h/kg and ED ≈ 2 kW h/m(3). According to SEM and EDX analysis, the purity of recovered copper was as high as 97.9%. Copyright © 2011 Elsevier B.V. All rights reserved.

  14. Solvent extraction of gold using ionic liquid based process

    NASA Astrophysics Data System (ADS)

    Makertihartha, I. G. B. N.; Zunita, Megawati; Rizki, Z.; Dharmawijaya, P. T.

    2017-01-01

    In decades, many research and mineral processing industries are using solvent extraction technology for metal ions separation. Solvent extraction technique has been used for the purification of precious metals such as Au and Pd, and base metals such as Cu, Zn and Cd. This process uses organic compounds as solvent. Organic solvents have some undesired properties i.e. toxic, volatile, excessive used, flammable, difficult to recycle, low reusability, low Au recovery, together with the problems related to the disposal of spent extractants and diluents, even the costs associated with these processes are relatively expensive. Therefore, a lot of research have boosted into the development of safe and environmentally friendly process for Au separation. Ionic liquids (ILs) are the potential alternative for gold extraction because they possess several desirable properties, such as a the ability to expanse temperature process up to 300°C, good solvent properties for a wide range of metal ions, high selectivity, low vapor pressures, stability up to 200°C, easy preparation, environmentally friendly (commonly called as "green solvent"), and relatively low cost. This review paper is focused in investigate of some ILs that have the potentials as solvent in extraction of Au from mineral/metal alloy at various conditions (pH, temperature, and pressure). Performances of ILs extraction of Au are studied in depth, i.e. structural relationship of ILs with capability to separate Au from metal ions aggregate. Optimal extraction conditon in order to gain high percent of Au in mineral processing is also investigated.

  15. 3D analysis of semiconductor devices: A combination of 3D imaging and 3D elemental analysis

    NASA Astrophysics Data System (ADS)

    Fu, Bianzhu; Gribelyuk, Michael A.

    2018-04-01

    3D analysis of semiconductor devices using a combination of scanning transmission electron microscopy (STEM) Z-contrast tomography and energy dispersive spectroscopy (EDS) elemental tomography is presented. 3D STEM Z-contrast tomography is useful in revealing the depth information of the sample. However, it suffers from contrast problems between materials with similar atomic numbers. Examples of EDS elemental tomography are presented using an automated EDS tomography system with batch data processing, which greatly reduces the data collection and processing time. 3D EDS elemental tomography reveals more in-depth information about the defect origin in semiconductor failure analysis. The influence of detector shadowing and X-rays absorption on the EDS tomography's result is also discussed.

  16. Sorption and desorption studies of a reactive azo dye on effective disposal of redundant material.

    PubMed

    Çelekli, Abuzer; Bozkurt, Hüseyin

    2013-07-01

    The effective disposal of redundant elephant dung (ED) is important for environmental protection and utilization of resource. The aim of this study was to remove a toxic-azo dye, Reactive Red (RR) 120, using this relatively cheap material as a new adsorbent. The FTIR-ATR spectra of ED powders before and after the sorption of RR 120 and zero point charge (pHzpc) of ED were determined. The sorption capacity of ED for removing of RR 120 were carried out as functions of particle size, adsorbent dose, pH, temperature, ionic strength, initial dye concentration, and contact time. Sorption isotherm, kinetic, activation energy, thermodynamic, and desorption parameters of RR 120 on ED were studied. The sorption process was found to be dependent on particle size, adsorbent dose, pH, temperature, ionic strength, initial dye concentration, and contact time. FTIR-ATR spectroscopy indicated that amine and amide groups have significant role on the sorption of RR 120 on ED. The pHzpc of ED was found to be 7.3. Sorption kinetic of RR 120 on ED was well described by sigmoidal Logistic model. The Langmuir isotherm was well fitted to the equilibrium data. The maximum sorption capacity was 95.71 mg g(-1). The sorption of RR 120 on ED was mainly physical and exothermic according to results of D-R isotherm, Arrhenius equation, thermodynamic, and desorption studies. The thermodynamic parameters showed that this process was feasible and spontaneous. This study showed that ED as a low-cost adsorbent had a great potential for the removal of RR 120 as an alternative eco-friendly process.

  17. Liquefaction process wherein solvents derived from the material liquefied and containing increased concentrations of donor species are employed

    DOEpatents

    Fant, B. T.; Miller, John D.; Ryan, D. F.

    1982-01-01

    An improved process for the liquefaction of solid carbonaceous materials wherein a solvent or diluent derived from the solid carbonaceous material being liquefied is used to form a slurry of the solid carbonaceous material and wherein the solvent or diluent comprises from about 65 to about 85 wt. % hydroaromatic components. The solvent is prepared by first separating a solvent or diluent distillate fraction from the liquefaction product, subjecting this distillate fraction to hydrogenation and then extracting the naphthenic components from the hydrogenated product. The extracted naphthenic components are then dehydrogenated and hydrotreated to produce additional hydroaromatic components. These components are combined with the solvent or diluent distillate fraction. The solvent may also contain hydroaromatic constituents prepared by extracting naphthenic components from a heavy naphtha, dehydrogenating the same and then hydrotreating the dehydrogenated product. When the amount of solvent produced in this manner exceeds that required for steady state operation of the liquefaction process a portion of the solvent or diluent distillated fraction will be withdrawn as product.

  18. Effect of solvent type on the nanoparticle formation of atorvastatin calcium by the supercritical antisolvent process.

    PubMed

    Kim, Min-Soo; Song, Ha-Seung; Park, Hee Jun; Hwang, Sung-Joo

    2012-01-01

    The aims of this study were to identify how the solvent selection affects particle formation and to examine the effect of the initial drug solution concentration on mean particle size and particle size distribution in the supercritical antisolvent (SAS) process. Amorphous atorvastatin calcium was precipitated from seven different solvents using the SAS process. Particles with mean particle size ranging between 62.6 and 1493.7 nm were obtained by varying organic solvent type and solution concentration. By changing the solvent, we observed large variations in particle size and particle size distribution, accompanied by different particle morphologies. Particles obtained from acetone and tetrahydrofuran (THF) were compact and spherical fine particles, whereas those from N-methylpyrrolidone (NMP) and dimethylsulfoxide (DMSO) were agglomerated, with rough surfaces and relatively larger particle sizes. Interestingly, the mean particle size of atorvastatin calcium increased with an increase in the boiling point of the organic solvent used. Thus, for atorvastatin particle formation via the SAS process, particle size was determined mainly by evaporation of the organic solvent into the antisolvent phase. In addition, the mean particle size was increased with increasing drug solution concentration. In this study, from the aspects of particle size and solvent toxicity, acetone was the better organic solvent for controlling nanoparticle formation of atorvastatin calcium.

  19. Solvent/non-solvent sintering: a novel route to create porous microsphere scaffolds for tissue regeneration.

    PubMed

    Brown, Justin L; Nair, Lakshmi S; Laurencin, Cato T

    2008-08-01

    Solvent/non-solvent sintering creates porous polymeric microsphere scaffolds suitable for tissue engineering purposes with control over the resulting porosity, average pore diameter, and mechanical properties. Five different biodegradable biocompatible polyphosphazenes exhibiting glass transition temperatures from -8 to 41 degrees C and poly (lactide-co-glycolide), (PLAGA) a degradable polymer used in a number of biomedical settings, were examined to study the versatility of the process and benchmark the process to heat sintering. Parameters such as: solvent/non-solvent sintering solution composition and submersion time effect the sintering process. PLAGA microsphere scaffolds fabricated with solvent/non-solvent sintering exhibited an interconnected porosity and pore size of 31.9% and 179.1 mum, respectively which was analogous to that of conventional heat sintered PLAGA microsphere scaffolds. Biodegradable polyphosphazene microsphere scaffolds exhibited a maximum interconnected porosity of 37.6% and a maximum compressive modulus of 94.3 MPa. Solvent/non-solvent sintering is an effective strategy for sintering polymeric microspheres, with a broad spectrum of glass transition temperatures, under ambient conditions making it an excellent fabrication route for developing tissue engineering scaffolds and drug delivery vehicles. (c) 2007 Wiley Periodicals, Inc.

  20. Solvent/Non-Solvent Sintering: A Novel Route to Create Porous Microsphere Scaffolds For Tissue Regeneration

    PubMed Central

    Brown, Justin L.; Nair, Lakshmi S.; Laurencin, Cato T.

    2009-01-01

    Solvent/non-solvent sintering creates porous polymeric microsphere scaffolds suitable for tissue engineering purposes with control over the resulting porosity, average pore diameter and mechanical properties. Five different biodegradable biocompatible polyphosphazenes exhibiting glass transition temperatures from −8°C to 41oC and poly(lactide-co-glycolide), (PLAGA) a degradable polymer used in a number of biomedical settings, were examined to study the versatility of the process and benchmark the process to heat sintering. Parameters such as: solvent/non-solvent sintering solution composition and submersion time effect the sintering process. PLAGA microsphere scaffolds fabricated with solvent/non-solvent sintering exhibited an interconnected porosity and pore size of 31.9% and 179.1µm respectively which was analogous to that of conventional heat sintered PLAGA microsphere scaffolds. Biodegradable polyphosphazene microsphere scaffolds exhibited a maximum interconnected porosity of 37.6% and a maximum compressive modulus of 94.3MPa. Solvent/non-solvent sintering is an effective strategy for sintering polymeric microspheres, with a broad spectrum of glass transition temperatures, under ambient conditions making it an excellent fabrication route for developing tissue engineering scaffolds and drug delivery vehicles. PMID:18161819

  1. Re-refining of waste petroleum by competing solubility characteristics

    NASA Astrophysics Data System (ADS)

    Byars, Michael Steven

    1998-11-01

    The United States produces over 1.3 billion gallons of used oil per year. Of the 1.3 billion gallons about 60% is used as fuel, nearly 20% is dumped into the environment, 13% is placed in landfills, 2% is re-refined into lube oil, and the remaining is either used for other purposes or incinerated. This is a great potential source of lubricating oil. The work presented here is a solvent extraction process using a solvent (highly miscible with the oil) and a co-solvent (slightly miscible with the oil). Extractions using isopropanol, ethanol, methyl tert-butylether and methanol are presented. The criteria used for evaluation of the extraction processes are yield, product viscosity index, and ash percent. The solvent/co-solvent combinations of MTBE and ethanol performed best and had the advantage of a common solvent/co-solvent in all extraction steps. The extraction process that provided the best results was a two step process using a combination solvent of MTBE and ethanol. The used oil was first extracted using MTBE/ethanol. The extracted oil was then contacted with a solvent combination composed of 80% ethanol. This solvent combination extracted the remaining additives from the oil. The recovered oil was nearly 60% by weight with a high viscosity index and no ash content. A preliminary battery limits design and economic analysis of the process was performed. A 500 bbl/day plant would have a capital cost of 1.9 million and an annual operation cost of 310,000. The plant as designed would produce 300 bbl/day of lube feedstock and have an ROI of 19%.

  2. Patient Reasons for Non-Urgent Utilization of the Dwight David Eisenhower Army Medical Center Emergency Department

    DTIC Science & Technology

    2004-01-01

    patient education opportunities, which may ultimately change both patient perception and ED utilization behavior. Statement of the... Patient education about the Emergency Department policies, triage process, and associated wait times should serve to narrow the gap between the patient’s...perceptions and the provider’s perceptions. The DDEAMC ED has made advancements in the patient education arena, as well as streamlining ED process

  3. Oiling the gate: a mobile application to improve the admissions process from the emergency department to an academic community hospital inpatient medicine service.

    PubMed

    Fung, Russell; Hyde, Jensen Hart; Davis, Mike

    2018-01-01

    The process of admitting patients from the emergency department (ED) to an academic internal medicine (AIM) service in a community teaching hospital is one fraught with variability and disorder. This results in an inconsistent volume of patients admitted to academic versus private hospitalist services and results in frustration of both ED and AIM clinicians. We postulated that implementation of a mobile application (app) would improve provider satisfaction and increase admissions to the academic service. The app was designed and implemented to be easily accessible to ED physicians, regularly updated by academic residents on call, and a real-time source of the number of open AIM admission spots. We found a significant improvement in ED and AIM provider satisfaction with the admission process. There was also a significant increase in admissions to the AIM service after implementation of the app. We submit that the implementation of a mobile app is a viable, cost-efficient, and effective method to streamline the admission process from the ED to AIM services at community-based hospitals.

  4. Study of the solubility and stability of polystyrene wastes in a dissolution recycling process

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Garcia, Maria Teresa; Gracia, Ignacio; Duque, Gema

    2009-06-15

    Dissolution with suitable solvents is one of the cheapest and more efficient processes for polystyrene waste management. In this work the solubility of polystyrene foams in several solvents benzene, toluene, xylene, tetrahydrofuran, chloroform, 1,3-butanediol, 2-butanol, linalool, geraniol, d-limonene, p-cymene, terpinene, phellandrene, terpineol, menthol, eucalyptol, cinnamaldheyde, nitrobenzene, N,N-dimethylformamide and water has been determined. Experimental results have shown that to develop a 'green process' the constituents of essential oils, d-limonene, p-cymene, terpinene, phellandrene, are the most appropriate solvents. The action of these solvent does not produce any degradation of polymer chains. The solubility of the polymer in the mentioned solvents at differentmore » temperatures has been investigated. The solvent can be easily recycled by distillation.« less

  5. The protective effect of the Vacha rhizome extract on chronic stress-induced immunodeficiency in rat.

    PubMed

    Sarjan, H N; Divyashree, S; Yajurvedi, H N

    2017-12-01

    Chronic stress is an inevitable factor in the modern day society which affects cell mediated as well as humoral immunity. There is a need to prevent stress effects with traditionally used herbs. The present study was undertaken to investigate the immunoprotective effect of Vacha (Acorus calamus L. Acoraceae) rhizome under stressful condition. Soxlet extraction of Vacha rhizome was performed with increasing polarity of solvents, i.e., petroleum ether to ethanol. The extract was concentrated by distilling off the solvent in flash evaporator and dried in desiccators. The benzene extract was found to have anti-stress property in our earlier studies and hence it was used in the present experiment. Extract was administered every day for 4 weeks orally to adult female rats prior to exposure to stress, restraint (1 h) and forced swimming exercise (15 min). Vacha rhizome extract significantly prevented the stress induced reduction in total and differential leukocytes count, immunoglobulin content, bone marrow cellularity and viability, lymphocytes counts in lymphoid organs, islands of white pulp of spleen (ED 50  = 10 mg, p < 0.001) and a significant increase in circulating immune complexes and apoptotic index of lymphoid organs (ED 50  = 10 mg, p < 0.001) compared to controls. The present study clearly indicates that Vacha extract not only prevents stress-induced suppression of immunity and structural involution of lymphoid organs, but also boosts immunity in normal rats. Therefore, it is suggested that Vacha extract administration maintains normal immunity despite the body experiencing stress.

  6. Biosynthesis of gold nanoparticles using Capsicum annuum var. grossum pulp extract and its catalytic activity

    NASA Astrophysics Data System (ADS)

    Yuan, Chun-Gang; Huo, Can; Yu, Shuixin; Gui, Bing

    2017-01-01

    Biological synthesis approach has been regarded as a green, eco-friendly and cost effective method for nanoparticles preparation without any toxic solvents and hazardous bi-products during the process. This present study reported a facile and rapid biosynthesis method for gold nanoparticles (GNPs) from Capsicum annuum var. grossum pulp extract in a single-pot process. The aqueous pulp extract was used as biotic reducing agent for gold nanoparticle growing. Various shapes (triangle, hexagonal, and quasi-spherical shapes) were observed within range of 6-37 nm. The UV-Vis spectra showed surface plasmon resonance (SPR) peak for the formed GNPs at 560 nm after 10 min incubation at room temperature. The possible influences of extract amount, gold ion concentration, incubation time, reaction temperature and solution pH were evaluated to obtain the optimized synthesis conditions. The effects of the experimental factors on NPs synthesis process were also discussed. The produced gold nanoparticles were characterized by transform electron microscopy (TEM), X-ray diffraction (XRD), energy dispersive X-ray (EDS) and Fourier Transform infrared spectroscopy (FTIR). The results demonstrated that the as-obtained GNPs were well dispersed and stable with good catalytic activity. Biomolecules in the aqueous extract were responsible for the capping and stabilization of GNPs.

  7. Bio-Derived, Binderless, Hierarchically Porous Carbon Anodes for Li-ion Batteries

    NASA Astrophysics Data System (ADS)

    Campbell, Brennan; Ionescu, Robert; Favors, Zachary; Ozkan, Cengiz S.; Ozkan, Mihrimah

    2015-09-01

    Here we explore the electrochemical performance of pyrolyzed skins from the species A. bisporus, also known as the Portobello mushroom, as free-standing, binder-free, and current collector-free Li-ion battery anodes. At temperatures above 900 °C, the biomass-derived carbon nanoribbon-like architectures undergo unique processes to become hierarchically porous. During heat-treatment, the oxygen and heteroatom-rich organics and potassium compounds naturally present in the mushroom skins play a mutual role in creating inner void spaces throughout the resulting carbon nanoribbons, which is a process analogous to KOH-activation of carbon materials seen in literature. The pores formed in the pyrolytic carbon nanoribbons range in size from sub-nanometer to tens of nanometers, making the nanoribbons micro, meso, and macroporous. Detailed studies were conducted on the carbon nanoribbons using SEM and TEM to study morphology, as well as XRD and EDS to study composition. The self-supporting nanoribbon anodes demonstrate significant capacity increase as they undergo additional charge/discharge cycles. After a pyrolysis temperature of 1100 °C, the pristine anodes achieve over 260 mAh/g after 700 cycles and a Coulombic efficiency of 101.1%, without the use of harmful solvents or chemical activation agents.

  8. Bio-Derived, Binderless, Hierarchically Porous Carbon Anodes for Li-ion Batteries.

    PubMed

    Campbell, Brennan; Ionescu, Robert; Favors, Zachary; Ozkan, Cengiz S; Ozkan, Mihrimah

    2015-09-29

    Here we explore the electrochemical performance of pyrolyzed skins from the species A. bisporus, also known as the Portobello mushroom, as free-standing, binder-free, and current collector-free Li-ion battery anodes. At temperatures above 900 °C, the biomass-derived carbon nanoribbon-like architectures undergo unique processes to become hierarchically porous. During heat-treatment, the oxygen and heteroatom-rich organics and potassium compounds naturally present in the mushroom skins play a mutual role in creating inner void spaces throughout the resulting carbon nanoribbons, which is a process analogous to KOH-activation of carbon materials seen in literature. The pores formed in the pyrolytic carbon nanoribbons range in size from sub-nanometer to tens of nanometers, making the nanoribbons micro, meso, and macroporous. Detailed studies were conducted on the carbon nanoribbons using SEM and TEM to study morphology, as well as XRD and EDS to study composition. The self-supporting nanoribbon anodes demonstrate significant capacity increase as they undergo additional charge/discharge cycles. After a pyrolysis temperature of 1100 °C, the pristine anodes achieve over 260 mAh/g after 700 cycles and a Coulombic efficiency of 101.1%, without the use of harmful solvents or chemical activation agents.

  9. Impact of an ABCDE team triage process combined with public guidance on the division of work in an emergency department.

    PubMed

    Kantonen, Jarmo; Lloyd, Robert; Mattila, Juho; Kauppila, Timo; Menezes, Ricardo

    2015-06-01

    To study the effects of applying an emergency department (ED) triage system, combined with extensive publicity in local media about the "right" use of emergency services, on the division of work between ED nurses and general practitioners (GPs). An observational and quasi-experimental study based on before-after comparisons. Implementation of the ABCDE triage system in a Finnish combined ED where secondary care is adjacent, and in a traditional primary care ED where secondary care is located elsewhere. GPs and nurses from two different primary care EDs. Numbers of monthly visits to different professional groups before and after intervention in the studied primary care EDs and numbers of monthly visits to doctors in the local secondary care ED. The beginning of the triage process increased temporarily the number of independent consultations and patient record entries by ED nurses in both types of studied primary care EDs and reduced the number of patient visits to a doctor compared with previous years but had no effect on doctor visits in the adjacent secondary care ED. No further decrease in the number of nurse or GP visits was observed by inhibiting the entrance of non-urgent patients. The ABCDE triage system combined with public guidance may reduce non-urgent patient visits to doctors in different kinds of primary care EDs without increasing visits in the secondary care ED. However, the additional work to implement the ABCDE system is mainly directed to nurses, which may pose a challenge for staffing.

  10. Tunable solvation effects on the size-selective fractionation of metal nanoparticles in CO2 gas-expanded solvents.

    PubMed

    Anand, Madhu; McLeod, M Chandler; Bell, Philip W; Roberts, Christopher B

    2005-12-08

    This paper presents an environmentally friendly, inexpensive, rapid, and efficient process for size-selective fractionation of polydisperse metal nanoparticle dispersions into multiple narrow size populations. The dispersibility of ligand-stabilized silver and gold nanoparticles is controlled by altering the ligand tails-solvent interaction (solvation) by the addition of carbon dioxide (CO2) gas as an antisolvent, thereby tailoring the bulk solvent strength. This is accomplished by adjusting the CO2 pressure over the liquid, resulting in a simple means to tune the nanoparticle precipitation by size. This study also details the influence of various factors on the size-separation process, such as the types of metal, ligand, and solvent, as well as the use of recursive fractionation and the time allowed for settling during each fractionation step. The pressure range required for the precipitation process is the same for both the silver and gold particles capped with dodecanethiol ligands. A change in ligand or solvent length has an effect on the interaction between the solvent and the ligand tails and therefore the pressure range required for precipitation. Stronger interactions between solvent and ligand tails require greater CO2 pressure to precipitate the particles. Temperature is another variable that impacts the dispersibility of the nanoparticles through changes in the density and the mole fraction of CO2 in the gas-expanded liquids. Recursive fractionation for a given system within a particular pressure range (solvent strength) further reduces the polydispersity of the fraction obtained within that pressure range. Specifically, this work utilizes the highly tunable solvent properties of organic/CO2 solvent mixtures to selectively size-separate dispersions of polydisperse nanoparticles (2 to 12 nm) into more monodisperse fractions (+/-2 nm). In addition to providing efficient separation of the particles, this process also allows all of the solvent and antisolvent to be recovered, thereby rendering it a green solvent process.

  11. Structural quality indicators to support quality of care for older people with cognitive impairment in emergency departments.

    PubMed

    Schnitker, Linda M; Martin-Khan, Melinda; Burkett, Ellen; Brand, Caroline A; Beattie, Elizabeth R A; Jones, Richard N; Gray, Len C

    2015-03-01

    The purpose of this study was to identify the structural quality of care domains and to establish a set of structural quality indicators (SQIs) for the assessment of care of older people with cognitive impairment in emergency departments (EDs). A structured approach to SQI development was undertaken including: 1) a comprehensive search of peer-reviewed and gray literature focusing on identification of evidence-based interventions targeting structure of care of older patients with cognitive impairment and existing SQIs; 2) a consultative process engaging experts in the care of older people and epidemiologic methods (i.e., advisory panel) leading to development of a draft set of SQIs; 3) field testing of drafted SQIs in eight EDs, leading to refinement of the SQI set; and 4) an independent voting process among the panelists for SQI inclusion in a final set, using preestablished inclusion and exclusion criteria. At the conclusion of the process, five SQIs targeting the management of older ED patients with cognitive impairment were developed: 1) the ED has a policy outlining the management of older people with cognitive impairment during the ED episode of care; 2) the ED has a policy outlining issues relevant to carers of older people with cognitive impairment, encompassing the need to include the (family) carer in the ED episode of care; 3) the ED has a policy outlining the assessment and management of behavioral symptoms, with specific reference to older people with cognitive impairment; 4) the ED has a policy outlining delirium prevention strategies, including the assessment of patients' delirium risk factors; and 5) the ED has a policy outlining pain assessment and management for older people with cognitive impairment. This article presents a set of SQIs for the evaluation of performance in caring for older people with cognitive impairment in EDs. © 2015 by the Society for Academic Emergency Medicine.

  12. The study on the extraction and recovery of Au from scrap of the used computer using chloride solvent

    NASA Astrophysics Data System (ADS)

    Oh, Su-ji; Choi, Eunju; Choi, Nagchoul; Park, Cheonyoung

    2013-04-01

    Recently, due to the realization of environmental problems of cyanide, it is a worldwide quest to find viable alternatives. One of the alternatives is a chloride solvent(chlorine-hypochlorite acid) with an appropriate oxidizing agent. The rate of dissolution of Au by chloride solvent is much faster than that by cyanide. Also, due to presence of chloride ions, there is no passivation of gold surfaces during chlorination. The objective of this work was to investigate the effect of Au extraction efficiency under various experimental conditions(pulp density, chlorine-hypochlorite ratio and concentration of NaCl) from scrap of the used computer by chloride solvent. In addition, the recovery experiment was conducted to examine of the precipitation efficiency of Au under various metabisulfite concentration from extracted solution. In an EDS analysis, valuable metals such as Cu, Sn, Sb, Al, Ni, Pb and Au were observed in scrap of the used computer. The result of extraction experiment showed that the highest extraction rate was obtained under 1% of pulp density with a chlorine-hypochlorite ratio of 2:1, and a concentration of NaCl at 2M. The highest Au recovery(precipitation) rate was observed the addition of sodium metabisulfite at 2M concentration. Under these conditions, chlorine-hypochlorite could effectively Au extraction from scrap of the used computer sections and the additive reagent using sodium metabisulfite could easily precipitate the Au from the chlorine-hypochlorite solution.

  13. Human Cognition and Performance.

    DTIC Science & Technology

    1985-05-01

    implications. In D. LaBerge & S. J. Samuels (Eds.), Basic processes in reading: Perception and comprehesion. Hillsdale, NJ: Eribaum. Anderson, J. A...Also pub- lished individually as follows: Some observations on mental models, in D. Gentner and A. Stevens (Eds.), Mental models, Hillsdale, NJ: Erlbaum...A. Stevens (Eds.), Mental Models. Hillsdale, NJ: Erlbaunm. Norman, D.A. (1983). Theories and models in cognitive psychology. In E. Douclkin (Ed

  14. Completing EdTPA: TSOL Candidate Performance and Reflection

    ERIC Educational Resources Information Center

    Micek, Timothy A.

    2017-01-01

    edTPA is a pre-service assessment process designed to determine if a new teacher is ready for the job. edTPA is part of a national movement towards the use of performance assessments in teacher education. As of 2014, 41 states (a) require a state-approved performance assessment like edTPA for program completion or for state licensure and/or state…

  15. Process modeling of emergency department patient flow: effect of patient length of stay on ED diversion.

    PubMed

    Kolker, Alexander

    2008-10-01

    A discreet event simulation methodology has been used to establish a quantitative relationship between Emergency Department (ED) performance characteristics, such as percent of time on ambulance diversion and the number of patients in queue in the waiting room, and the upper limits of patient length of stay (LOS). A simulation process model of ED patient flow has been developed that took into account a significant difference between LOS distributions of patients discharged home and patients admitted into the hospital. Using simulation model it has been identified that ED diversion could be negligible (less than approximately 0.5%) if patients discharged home stay in ED not more than 5 h, and patients admitted into the hospital stay in ED not more than 6 h Using full factorial design of experiments with two factors and the model's predicted percent diversion as a response function, other combinations of LOS upper limits have been determined that would result in low ED percent diversion as well. It has also been determined that if the number of patients exceeds 11 in queue in ED waiting room then the diversion percent is rapidly increasing.

  16. Performance of Emergency Department Screening Criteria for an Early ECG to Identify ST-Segment Elevation Myocardial Infarction.

    PubMed

    Yiadom, Maame Yaa A B; Baugh, Christopher W; McWade, Conor M; Liu, Xulei; Song, Kyoung Jun; Patterson, Brian W; Jenkins, Cathy A; Tanski, Mary; Mills, Angela M; Salazar, Gilberto; Wang, Thomas J; Dittus, Robert S; Liu, Dandan; Storrow, Alan B

    2017-02-23

    Timely diagnosis of ST-segment elevation myocardial infarction (STEMI) in the emergency department (ED) is made solely by ECG. Obtaining this test within 10 minutes of ED arrival is critical to achieving the best outcomes. We investigated variability in the timely identification of STEMI across institutions and whether performance variation was associated with the ED characteristics, the comprehensiveness of screening criteria, and the STEMI screening processes. We examined STEMI screening performance in 7 EDs, with the missed case rate (MCR) as our primary end point. The MCR is the proportion of primarily screened ED patients diagnosed with STEMI who did not receive an ECG within 15 minutes of ED arrival. STEMI was defined by hospital discharge diagnosis. Relationships between the MCR and ED characteristics, screening criteria, and STEMI screening processes were assessed, along with differences in door-to-ECG times for captured versus missed patients. The overall MCR for all 7 EDs was 12.8%. The lowest and highest MCRs were 3.4% and 32.6%, respectively. The mean difference in door-to-ECG times for captured and missed patients was 31 minutes, with a range of 14 to 80 minutes of additional myocardial ischemia time for missed cases. The prevalence of primarily screened ED STEMIs was 0.09%. EDs with the greatest informedness (sensitivity+specificity-1) demonstrated superior performance across all other screening measures. The 29.2% difference in MCRs between the highest and lowest performing EDs demonstrates room for improving timely STEMI identification among primarily screened ED patients. The MCR and informedness can be used to compare screening across EDs and to understand variable performance. © 2017 The Authors. Published on behalf of the American Heart Association, Inc., by Wiley Blackwell.

  17. One-step fabrication of novel superhydrophobic and superoleophilic sponge with outstanding absorbency and flame-retardancy for the selective removal of oily organic solvent from water

    NASA Astrophysics Data System (ADS)

    Xiang, Yuqian; Pang, Youyou; Jiang, Xiaomei; Huang, Jie; Xi, Fengna; Liu, Jiyang

    2018-01-01

    Absorbent materials integrated with superhydrophobicity, superoleophilicity and flame-retardancy are highly desired in the adsorption/removal of flammable oils/organic compounds as well as reducing the risk of fire and explosion. Here, one-step fabrication of novel superhydrophobic and superoleophilic sponge with outstanding absorbency and flame-retardancy was presented. Using raw melamine (ME) sponge as the supporting matrix, the formation of polydopamine (PDA) nanoaggregates via in-situ self-polymerization of high-concentrated dopamine and the covalent grafting of hydrophobic n-dodecylthiol (DT) onto PDA were combined in a feasible alkaline water/ethanol medium. As investigated by scanning electron microscopy (SEM) and X-ray energy-dispersive spectroscopy (EDS), the as-prepared ME/PDA/DT sponge possessed hierarchical structure with submicron PDA nanoaggregates containing DT motif (low surface energy) on 3D interconnected porous network. It exhibited superhydrophobic (water contact angle 157.7°) and superoleophilic (oily/organic solvent contact angle 0° properties. Owing to the highly porous structure, superhydrophobic property, chemical and mechanical stability, the ME/PDA/DT sponge exhibited outstanding absorbency properties of oily organic solvents including fast absorption kinetics, high absorption capacity, and easy reusability. Also, the ME/PDA/DT sponge could be used for one-line continuous organic solvent/water separation. More interestingly, the ME/PDA/DT sponge demonstrated improved flame-retardant property as compared to the intrinsic flame-retardant nature of the raw melamine sponge. Consequently, the risk of fire and explosion was expected to reduce when the fabricated sponge was used as an absorbent for flammable oils and organic compounds. The ease of the one-step superhydrophobic/superoleophilic modification and the promising feature of the obtained materials exhibit great potential for application in oils/organic solvents clean-up.

  18. [Supercritical and near-critical fluid solvents assisted reaction and separation processes].

    PubMed

    Song, R; Zeng, J; Zhong, B

    2001-11-01

    The tunability of supercritical and near-critical fluid (S/NCF) solvents offers environmental improvements and economic advantages from improved performances and flexibility for separation and reaction processes through density changes or cosolvents. The paper reviews the sustainable reaction and separation processes in S/NCF solvents such as supercritical carbon dioxide and near-critical water.

  19. Bench-Scale Development of a Non-Aqueous Solvent (NAS) CO2 Capture Process for Coal-Fired Power Plants

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Lail, Marty

    The project aimed to advance RTI’s non-aqueous amine solvent technology by improving the solvent to reduce volatility, demonstrating long-term continuous operation at lab- (0.5 liters solvent) and bench-scale (~120 liters solvent), showing low reboiler heat duty measured during bench-scale testing, evaluating degradation products, building a rate-based process model, and evaluating the techno-economic performance of the process. The project team (RTI, SINTEF, Linde Engineering) and the technology performed well in each area of advancement. The modifications incorporated throughout the project enabled the attainment of target absorber and regenerator conditions for the process. Reboiler duties below 2,000 kJt/kg CO2 were observed inmore » a bench-scale test unit operated at RTI.« less

  20. Chemically assisted mechanical refrigeration process

    DOEpatents

    Vobach, Arnold R.

    1987-01-01

    There is provided a chemically assisted mechanical refrigeration process including the steps of: mechanically compressing a refrigerant stream which includes vaporized refrigerant; contacting the refrigerant with a solvent in a mixer (11) at a pressure sufficient to promote substantial dissolving of the refrigerant in the solvent in the mixer (11) to form a refrigerant-solvent solution while concurrently placing the solution in heat exchange relation with a working medium to transfer energy to the working medium, said refrigerant-solvent solution exhibiting a negative deviation from Raoult's Law; reducing the pressure over the refrigerant-solvent solution in an evaporator (10) to allow the refrigerant to vaporize and substantially separate from the solvent while concurrently placing the evolving refrigerant-solvent solution in heat exchange relation with a working medium to remove energy from the working medium to thereby form a refrigerant stream and a solvent stream; and passing the solvent and refrigerant stream from the evaporator.

  1. Chemically assisted mechanical refrigeration process

    DOEpatents

    Vobach, Arnold R.

    1987-01-01

    There is provided a chemically assisted mechanical refrigeration process including the steps of: mechanically compressing a refrigerant stream which includes vaporized refrigerant; contacting the refrigerant with a solvent in a mixer (11) at a pressure sufficient to promote substantial dissolving of the refrigerant in the solvent in the mixer (11) to form a refrigerant-solvent solution while concurrently placing the solution in heat exchange relation with a working medium to transfer energy to the working medium, said refrigerant-solvent solution exhibiting a negative deviation from Raoult's Law; reducing the pressure over the refrigerant-solvent solution in an evaporator (10) to allow the refrigerant to vaporize and substantially separate from the solvent while concurrently placing he evolving refrigerant-solvent solution in heat exchange relation with a working medium to remove energy from the working medium to thereby form a refrigerant stream and a solvent stream; and passing the solvent and refrigerant stream from the evaporator.

  2. Chemically assisted mechanical refrigeration process

    DOEpatents

    Vobach, A.R.

    1987-06-23

    There is provided a chemically assisted mechanical refrigeration process including the steps of: mechanically compressing a refrigerant stream which includes vaporized refrigerant; contacting the refrigerant with a solvent in a mixer at a pressure sufficient to promote substantial dissolving of the refrigerant in the solvent in the mixer to form a refrigerant-solvent solution while concurrently placing the solution in heat exchange relation with a working medium to transfer energy to the working medium, said refrigerant-solvent solution exhibiting a negative deviation from Raoult's Law; reducing the pressure over the refrigerant-solvent solution in an evaporator to allow the refrigerant to vaporize and substantially separate from the solvent while concurrently placing the evolving refrigerant-solvent solution in heat exchange relation with a working medium to remove energy from the working medium to thereby form a refrigerant stream and a solvent stream; and passing the solvent and refrigerant stream from the evaporator. 5 figs.

  3. Chemically assisted mechanical refrigeration process

    DOEpatents

    Vobach, A.R.

    1987-11-24

    There is provided a chemically assisted mechanical refrigeration process including the steps of: mechanically compressing a refrigerant stream which includes vaporized refrigerant; contacting the refrigerant with a solvent in a mixer at a pressure sufficient to promote substantial dissolving of the refrigerant in the solvent in the mixer to form a refrigerant-solvent solution while concurrently placing the solution in heat exchange relation with a working medium to transfer energy to the working medium, said refrigerant-solvent solution exhibiting a negative deviation from Raoult's Law; reducing the pressure over the refrigerant-solvent solution in an evaporator to allow the refrigerant to vaporize and substantially separate from the solvent while concurrently placing the evolving refrigerant-solvent solution in heat exchange relation with a working medium to remove energy from the working medium to thereby form a refrigerant stream and a solvent stream; and passing the solvent and refrigerant stream from the evaporator. 5 figs.

  4. Anxiety Sensitivity and Cognitive-Based Smoking Processes: Testing the Mediating Role of Emotion Dysregulation among Treatment-Seeking Daily Smokers

    PubMed Central

    Johnson, Kirsten A.; Farris, Samantha G.; Schmidt, Norman B.; Zvolensky, Michael J.

    2012-01-01

    Objective The current study investigated whether emotion dysregulation (ED; difficulties in the self-regulation of affective states) mediated relations between anxiety sensitivity (AS; fear of anxiety and related sensations) and cognitive-based smoking processes. Method Participants (n = 197; 57.5% male; Mage = 38.0) were daily smokers recruited as part of a randomized control trial for smoking cessation. Results AS was uniquely associated with all smoking processes. Moreover, ED significantly mediated relations between AS and the smoking processes. Conclusions Findings suggest that ED is an important construct to consider in relations between AS and cognitive-based smoking processes among adult treatment-seeking smokers. PMID:22540436

  5. COMPUTER-AIDED SOLVENT DESIGN FOR POLLUTION PREVENTION: PARIS II

    EPA Science Inventory

    Solvent substitution is an attractive way of elijminating the use of regulated solvents because it usually does not require major chanages in existing processes, equipment or operations. Successful solvent substitution is dependent on finding solvents that are as effective or be...

  6. ODC-Free Solvent Implementation Issues for Vulcanized Rubber and Bond Systems

    NASA Technical Reports Server (NTRS)

    Hodgson, James R.; McCool, Alex (Technical Monitor)

    2001-01-01

    Thiokol Propulsion has worked extensively to replace 1,1,1-trichloroethane (TCA) with ozone depleting chemicals (ODC)-free solvents for use in the manufacture of the Reusable Solid Rocket Motor (RSRM) for the Space Shuttle Program. As Thiokol has transitioned from sub-scale to full-scale testing and implementation of these new solvents, issues have been discovered which have required special attention. The original intent of Thiokol's solvent replacement strategy was to replace TCA with a single drop-in solvent for all equivalent applications. We have learned that a single candidate does not exist for replacing TCA. Solvent incompatibility with process materials has caused us to seek for niche solvents and/or processing changes that provide an ODC-free solution for special applications. This paper addresses some of the solvent incompatibilities, which have lead to processes changes and possible niche solvent usage. These incompatibilities were discovered during full-scale testing of ODC-free solvents and relate to vulcanized rubber and bond systems in the RSRM. Specifically, the following items are presented: (1) Cure effects of d-limonene based solvents on Silica Filled Ethylene Propylene Diene Monomer (SF-EPDM) rubber. During full-scale test operations, Thiokol discovered that d-limonene (terpene) based solvents inhibit the cure of EPDM rubber. Subsequent testing showed the same issue with Nitrile Butadiene Rubber (NBR). Also discussed are efforts to minimize uncured rubber exposure to solvents; and (2) Cured bond system sensitivity to ODC-free solvents. During full scale testing it was discovered that a natural rubber to steel vulcanized bond could degrade after prolonged exposure to ODC-free solvents. Follow on testing showed that low vapor pressure and residence time seemed to be most likely cause for failure.

  7. High Energy Density in Azobenzene-based Materials for Photo-Thermal Batteries via Controlled Polymer Architecture and Polymer-Solvent Interactions.

    PubMed

    Jeong, Seung Pyo; Renna, Lawrence A; Boyle, Connor J; Kwak, Hyunwook S; Harder, Edward; Damm, Wolfgang; Venkataraman, Dhandapani

    2017-12-19

    Energy densities of ~510 J/g (max: 698 J/g) have been achieved in azobenzene-based syndiotactic-rich poly(methacrylate) polymers. The processing solvent and polymer-solvent interactions are important to achieve morphologically optimal structures for high-energy density materials. This work shows that morphological changes of solid-state syndiotactic polymers, driven by different solvent processings play an important role in controlling the activation energy of Z-E isomerization as well as the shape of the DSC exotherm. Thus, this study shows the crucial role of processing solvents and thin film structure in achieving higher energy densities.

  8. Influence of solvent polarity and supersaturation on template-induced nucleation of carbamazepine crystal polymorphs

    NASA Astrophysics Data System (ADS)

    Parambil, Jose V.; Poornachary, Sendhil K.; Tan, Reginald B. H.; Heng, Jerry Y. Y.

    2017-07-01

    Studies on the use of template surfaces to induce heterogeneous crystal nucleation have gained momentum in recent years-with potential applications in selective crystallisation of polymorphs and in the generation of seed crystals in a continuous crystallisation process. In developing a template-assisted solution crystallisation process, the kinetics of homogeneous versus heterogeneous crystal nucleation could be influenced by solute-solvent, solute-template, and solvent-template interactions. In this study, we report the effect of solvents of varying polarity on the nucleation of carbamazepine (CBZ) crystal polymorphs, a model active pharmaceutical ingredient. The experimental results demonstrate that functionalised template surfaces are effective in promoting crystallisation of either the metastable (form II) or stable (form III) polymorphs of CBZ only in moderately (methanol, ethanol, isopropanol) and low polar (toluene) solvents. A solvent with high polarity (acetonitrile) is thought to mask the template effect on heterogeneous nucleation due to strong solute-solvent and solvent-template interactions. The current study highlights that a quality-by-design (QbD) approach-considering the synergistic effects of solute concentration, solvent type, solution temperature, and template surface chemistry on crystal nucleation-is critical to the development of a template-induced crystallisation process.

  9. Improved electron transport properties of n-type naphthalenediimide polymers through refined molecular ordering and orientation induced by processing solvents.

    PubMed

    An, Yujin; Long, Dang Xuan; Kim, Yiho; Noh, Yong-Young; Yang, Changduk

    2016-05-14

    To determine the role played by the choice of processing solvents in governing the photophysics, microstructure, and charge carrier transport in naphthalenediimide (NDI)-based polymers, we have prepared two new NDI-bithiophene (T2)- and NDI-thienothiophene (TTh)-containing polymers with hybrid siloxane pentyl chains (SiC5) (P(NDI2SiC5-T2) and P(NDI2SiC5-TTh)). Among the various processing solvents studied here, the films prepared using chloroform exhibited far better electron mobilities (0.16 ± 0.1-0.21 ± 0.05 cm(2) V(-1) s(-1)) than the corresponding samples prepared from different solvents, exceeding one order of magnitude higher, indicating the significant influence of the processing solvent on the charge transport. Upon thin-film analysis using atomic force microscopy and grazing incidence X-ray diffraction, we discovered that molecular ordering and orientation are affected by the choice of the processing solvent, which is responsible for the change in the transport characteristics of this class of polymers.

  10. Thermal stability study of a new guanidine suppressor for the next-generation caustic-side solvent extraction process

    DOE PAGES

    Hill, Talon G.; Ensor, Dale D.; Delmau, Lætitia Helene; ...

    2016-02-06

    Cesium stripping performance of thermally stressed solvent degrades slowly over time in batch tests of the Next Generation Caustic-Side Solvent Extraction (NGS) process. NGS is currently used at pilot scale at the Savannah River Site for the selective removal of cesium from high-level salt waste. Recently a new guanidine, N,N',N" -tris(3,7-dimethyloctyl)guanidine (TiDG), was chosen for use as the suppressor, a lipophilic organic base needed for stripping, and the present study was undertaken to address the question of its stability. The NGS process solvent was evaluated for a period of three months under a variety of temperature and storage conditions. Themore » performance of the solvent was tested at 30-day increments using a standard extraction, scrub, strip, and extraction (ES 2S 3E) sequence. Lastly, the results provide insight on the effects of storage and process conditions, the stripping behavior of TiDG, and the stability of the new solvent composition.« less

  11. Thermal stability study of a new guanidine suppressor for the next-generation caustic-side solvent extraction process

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Hill, Talon G.; Ensor, Dale D.; Delmau, Lætitia Helene

    Cesium stripping performance of thermally stressed solvent degrades slowly over time in batch tests of the Next Generation Caustic-Side Solvent Extraction (NGS) process. NGS is currently used at pilot scale at the Savannah River Site for the selective removal of cesium from high-level salt waste. Recently a new guanidine, N,N',N" -tris(3,7-dimethyloctyl)guanidine (TiDG), was chosen for use as the suppressor, a lipophilic organic base needed for stripping, and the present study was undertaken to address the question of its stability. The NGS process solvent was evaluated for a period of three months under a variety of temperature and storage conditions. Themore » performance of the solvent was tested at 30-day increments using a standard extraction, scrub, strip, and extraction (ES 2S 3E) sequence. Lastly, the results provide insight on the effects of storage and process conditions, the stripping behavior of TiDG, and the stability of the new solvent composition.« less

  12. PREPARATION OF ALKYL PYROPHOSPHATE EXTRACTANTS

    DOEpatents

    Levine, C.A.; Skiens, W.E.; Moore, G.R.

    1960-08-01

    A process for providing superior solvent extractants for metal recovery processes is given wherein the extractant comprises an alkyl pyrophosphoric acid ester dissolved in an organic solvent diluent. Finely divided solid P/sub 2/O/ sub 5/ is slurried in an organic solvent-diluent selected from organic solvents such as kerosene, benzene, chlorobenzene, toluene, etc. An alcohol selected from the higher alcohols having 4 to 17 carbon atoms. e.g.. hexanol-1. heptanol-3, octanol-1. 2.6-dimethyl-heptanol-4, and decanol-1, is rapidly added to the P/sub 2/O/sub 5/ slurry in the amount of about 2 moles of alcohol to 1 mole of P/sub 2/ O/sub 5/. The temperature is maintained below about 110 deg C during the course of the P/sub 2/O/sub 5/-alcohol reaction. An alkyl pyrophosphate extractant compound is formed as a consequence of the reaction process. The alkyl pyrophosphate solvent-diluent extractant phase is useful in solvent extraction metal recovery processes.

  13. Process for the removal of impurities from combustion fullerenes

    DOEpatents

    Alford, J. Michael; Bolskar, Robert

    2005-08-02

    The invention generally relates to purification of carbon nanomaterials, particularly fullerenes, by removal of PAHs and other hydrocarbon impurities. The inventive process involves extracting a sample containing carbon nanomaterials with a solvent in which the PAHs are substantially soluble but in which the carbon nanomaterials are not substantially soluble. The sample can be repeatedly or continuously extracted with one or more solvents to remove a greater amount of impurities. Preferred solvents include ethanol, diethyl ether, and acetone. The invention also provides a process for efficiently separating solvent extractable fullerenes from samples containing fullerenes and PAHs wherein the sample is extracted with a solvent in which both fullerenes and PAHs are substantially soluble and the sample extract then undergoes selective extraction to remove PAHs. Suitable solvents in which both fullerenes and PAHs are soluble include o-xylene, toluene, and o-dichlorobenzene. The purification process is capable of treating quantities of combustion soot in excess of one kilogram and can produce fullerenes or fullerenic soot of suitable purity for many applications.

  14. Alternative Solvents/Technologies for Paint Stripping: Phase 1.

    DTIC Science & Technology

    1994-03-01

    processes . Three phases of study are defined: Phase I, identify alternate solvents/strippers and screen them; Phase II, field test solvent/ strippers...Section Title Page 1 Metal Refinishing Process - Immersion Method ............... 8 2 Phase Summary Chart ........................ 12 3 The...of the following: (a) nontoxic chemical formulations, (b) new process development, and (c) new coating reformulations. This program consists of three

  15. Automated process for solvent separation of organic/inorganic substance

    DOEpatents

    Schweighardt, F.K.

    1986-07-29

    There is described an automated process for the solvent separation of organic/inorganic substances that operates continuously and unattended and eliminates potential errors resulting from subjectivity and the aging of the sample during analysis. In the process, metered amounts of one or more solvents are passed sequentially through a filter containing the sample under the direction of a microprocessor control apparatus. The mixture in the filter is agitated by ultrasonic cavitation for a timed period and the filtrate is collected. The filtrate of each solvent extraction is collected individually and the residue on the filter element is collected to complete the extraction process. 4 figs.

  16. Automated process for solvent separation of organic/inorganic substance

    DOEpatents

    Schweighardt, Frank K.

    1986-01-01

    There is described an automated process for the solvent separation of organic/inorganic substances that operates continuously and unattended and eliminates potential errors resulting from subjectivity and the aging of the sample during analysis. In the process, metered amounts of one or more solvents are passed sequentially through a filter containing the sample under the direction of a microprocessor control apparatus. The mixture in the filter is agitated by ultrasonic cavitation for a timed period and the filtrate is collected. The filtrate of each solvent extraction is collected individually and the residue on the filter element is collected to complete the extraction process.

  17. Process for producing low-sulfur boiler fuel by hydrotreatment of solvent deashed SRC

    DOEpatents

    Roberts, George W.; Tao, John C.

    1985-01-01

    In this invention, a process is disclosed characterized by heating a slurry of coal in the presence of a process-derived recycle solvent and passing same to a dissolver zone, separating the resultant gases and liquid/solid products therefrom, vacuum distilling the liquid/solids products, separating the portions of the liquid/solids vacuum distillation effluent into a solid ash, unconverted coal particles and SRC material having a boiling point above 850.degree. F. and subjecting same to a critical solvent deashing step to provide an ash-free SRC product. The lighter liquid products from the vacuum distillation possess a boiling point below 850.degree. F. and are passed through a distillation tower, from which recycled solvent is recovered in addition to light distillate boiling below 400.degree. F. (overhead). The ash-free SRC product in accompanyment with at least a portion of the process derived solvent is passed in combination to a hydrotreating zone containing a hydrogenation catalyst and in the presence of hydrogen is hydroprocessed to produce a desulfurized and denitrogenized low-sulfur, low-ash boiler fuel and a process derived recycle solvent which is recycled to slurry the coal in the beginning of the process before heating.

  18. Consensus Statement on Advancing Research in Emergency Department Operations and Its Impact on Patient Care

    PubMed Central

    Ward, Michael J.; Chang, Anna Marie; Pines, Jesse M.; Jouriles, Nick; Yealy, Donald M.

    2016-01-01

    The Consensus Conference on “Advancing Research in Emergency Department (ED) Operations and Its Impact on Patient Care,” hosted by The ED Operations Study Group (EDOSG), convened to craft a framework for future investigations in this important but underserved area. The EDOSG is a research consortium dedicated to promoting evidence based clinical practice in Emergency Medicine. The consensus process format was a modified version of the NIH Model for Consensus Conference Development. Recommendations provide an action plan for how to improve ED operations study design, create a facilitating research environment, identify data measures of value for process and outcomes research, and disseminate new knowledge in this area. Specifically, we called for eight key initiatives: 1) the development of universal measures for ED patient care processes; 2) attention to patient outcomes, in addition to process efficiency and best practice compliance; 3) the promotion of multi-site clinical operations studies to create more generalizable knowledge; 4) encouraging the use of mixed methods to understand the social community and human behavior factors that influence ED operations; 5) the creation of robust ED operations research registries to drive stronger evidence based research, 6) prioritizing key clinical questions with the input of patients, clinicians, medical leadership, emergency medicine organizations, payers, and other government stakeholders; 7) more consistently defining the functional components of the ED care system including observation units, fast tracks, waiting rooms, laboratories and radiology sub-units; and 8) maximizing multidisciplinary knowledge dissemination via emergency medicine, public health, general medicine, operations research and nontraditional publications. PMID:26014365

  19. Consensus statement on advancing research in emergency department operations and its impact on patient care.

    PubMed

    Yiadom, Maame Yaa A B; Ward, Michael J; Chang, Anna Marie; Pines, Jesse M; Jouriles, Nick; Yealy, Donald M

    2015-06-01

    The consensus conference on "Advancing Research in Emergency Department (ED) Operations and Its Impact on Patient Care," hosted by The ED Operations Study Group (EDOSG), convened to craft a framework for future investigations in this important but understudied area. The EDOSG is a research consortium dedicated to promoting evidence-based clinical practice in emergency medicine. The consensus process format was a modified version of the NIH Model for Consensus Conference Development. Recommendations provide an action plan for how to improve ED operations study design, create a facilitating research environment, identify data measures of value for process and outcomes research, and disseminate new knowledge in this area. Specifically, we call for eight key initiatives: 1) the development of universal measures for ED patient care processes; 2) attention to patient outcomes, in addition to process efficiency and best practice compliance; 3) the promotion of multisite clinical operations studies to create more generalizable knowledge; 4) encouraging the use of mixed methods to understand the social community and human behavior factors that influence ED operations; 5) the creation of robust ED operations research registries to drive stronger evidence-based research; 6) prioritizing key clinical questions with the input of patients, clinicians, medical leadership, emergency medicine organizations, payers, and other government stakeholders; 7) more consistently defining the functional components of the ED care system, including observation units, fast tracks, waiting rooms, laboratories, and radiology subunits; and 8) maximizing multidisciplinary knowledge dissemination via emergency medicine, public health, general medicine, operations research, and nontraditional publications. © 2015 by the Society for Academic Emergency Medicine.

  20. Identifying causes of laboratory turnaround time delay in the emergency department.

    PubMed

    Jalili, Mohammad; Shalileh, Keivan; Mojtahed, Ali; Mojtahed, Mohammad; Moradi-Lakeh, Maziar

    2012-12-01

    Laboratory turnaround time (TAT) is an important determinant of patient stay and quality of care. Our objective is to evaluate laboratory TAT in our emergency department (ED) and to generate a simple model for identifying the primary causes for delay. We measured TATs of hemoglobin, potassium, and prothrombin time tests requested in the ED of a tertiary-care, metropolitan hospital during a consecutive one-week period. The time of different steps (physician order, nurse registration, blood-draw, specimen dispatch from the ED, specimen arrival at the laboratory, and result availability) in the test turnaround process were recorded and the intervals between these steps (order processing, specimen collection, ED waiting, transit, and within-laboratory time) and total TAT were calculated. Median TATs for hemoglobin and potassium were compared with those of the 1990 Q-Probes Study (25 min for hemoglobin and 36 min for potassium) and its recommended goals (45 min for 90% of tests). Intervals were compared according to the proportion of TAT they comprised. Median TATs (170 min for 132 hemoglobin tests, 225 min for 172 potassium tests, and 195.5 min for 128 prothrombin tests) were drastically longer than Q-Probes reported and recommended TATs. The longest intervals were ED waiting time and order processing.  Laboratory TAT varies among institutions, and data are sparse in developing countries. In our ED, actions to reduce ED waiting time and order processing are top priorities. We recommend utilization of this model by other institutions in settings with limited resources to identify their own priorities for reducing laboratory TAT.

  1. Green-Solvent-Processable, Dopant-Free Hole-Transporting Materials for Robust and Efficient Perovskite Solar Cells.

    PubMed

    Lee, Junwoo; Malekshahi Byranvand, Mahdi; Kang, Gyeongho; Son, Sung Y; Song, Seulki; Kim, Guan-Woo; Park, Taiho

    2017-09-06

    In addition to having proper energy levels and high hole mobility (μ h ) without the use of dopants, hole-transporting materials (HTMs) used in n-i-p-type perovskite solar cells (PSCs) should be processed using green solvents to enable environmentally friendly device fabrication. Although many HTMs have been assessed, due to the limited solubility of HTMs in green solvents, no green-solvent-processable HTM has been reported to date. Here, we report on a green-solvent-processable HTM, an asymmetric D-A polymer (asy-PBTBDT) that exhibits superior solubility even in the green solvent, 2-methylanisole, which is a known food additive. The new HTM is well matched with perovskites in terms of energy levels and attains a high μ h (1.13 × 10 -3 cm 2 /(V s)) even without the use of dopants. Using the HTM, we produced robust PSCs with 18.3% efficiency (91% retention after 30 days without encapsulation under 50%-75% relative humidity) without dopants; with dopants (bis(trifluoromethanesulfonyl) imide and tert-butylpyridine, a 20.0% efficiency was achieved. Therefore, it is a first report for a green-solvent-processable hole-transporting polymer, exhibiting the highest efficiencies reported so far for n-i-p devices with and without the dopants.

  2. Removing Biostatic Agents From Fermentation Solutions

    NASA Technical Reports Server (NTRS)

    Du Fresne, E. R.

    1984-01-01

    Liquid carbon dioxide inexpensive solvent. Inexpensive process proposed for removing such poisons as furfural and related compounds from fermentation baths of biomass hydrolysates. New process based on use of liquid carbon dioxide as extraction solvent. Liquid CO2 preferable to such other liquid solvents as ether or methylene chloride.

  3. The dual role of sulfur-containing amino acids in the synthesis of IV-VI semiconductor nanocrystals: a mechanochemical approach.

    PubMed

    Baláž, Peter; Baláž, Matej; Caplovičová, Mária; Zorkovská, Anna; Caplovič, Lubomír; Psotka, Miroslav

    2014-01-01

    PbS@cystine nanocrystals were synthesized mechanochemically, with lead acetate and L-cystine being used as the lead and sulfur precursors, respectively. The resulting nanocrystals are 22-34 nm in size, well-faceted and octahedral in shape. Characterization by XRD, FT-IR, NMR, FE-SEM, EDS, TEM (HRTEM) and surface area measurement methods showed that the particles are single, defect-free crystals with a high crystallinity. Furthermore, the crystals were prepared using a solvent-free procedure that was performed under ambient temperature and atmospheric pressure.

  4. Sample Results From The Extraction, Scrub, And Strip Test For The Blended NGS Solvent

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Washington, A. L. II; Peters, T. B.

    This report summarizes the results of the extraction, scrub, and strip testing for the September 2013 sampling of the Next Generation Solvent (NGS) Blended solvent from the Modular Caustic Side-Solvent Extraction Unit (MCU) Solvent Hold Tank. MCU is in the process of transitioning from the BOBCalixC6 solvent to the NGS Blend solvent. As part of that transition, MCU has intentionally created a blended solvent to be processed using the Salt Batch program. This sample represents the first sample received from that blended solvent. There were two ESS tests performed where NGS blended solvent performance was assessed using either the Tankmore » 21 material utilized in the Salt Batch 7 analyses or a simulant waste material used in the V-5/V-10 contactor testing. This report tabulates the temperature corrected cesium distribution, or D Cs values, step recovery percentage, and actual temperatures recorded during the experiment. This report also identifies the sample receipt date, preparation method, and analysis performed in the accumulation of the listed values. The calculated extraction D Cs values using the Tank 21H material and simulant are 59.4 and 53.8, respectively. The DCs values for two scrub and three strip processes for the Tank 21 material are 4.58, 2.91, 0.00184, 0.0252, and 0.00575, respectively. The D-values for two scrub and three strip processes for the simulant are 3.47, 2.18, 0.00468, 0.00057, and 0.00572, respectively. These values are similar to previous measurements of Salt Batch 7 feed with lab-prepared blended solvent. These numbers are considered compatible to allow simulant testing to be completed in place of actual waste due to the limited availability of feed material.« less

  5. Differentiation of South American crack and domestic (US) crack cocaine via headspace-gas chromatography/mass spectrometry.

    PubMed

    Colley, Valerie L; Casale, John F

    2015-03-01

    South American 'crack' cocaine, produced directly from coca leaf, can be distinguished from US domestically produced crack on the basis of occluded solvent profiles. In addition, analysis of domestically produced crack indicates the solvents that were used for cocaine hydrochloride (HCl) processing in South America. Samples of cocaine base (N=3) from South America and cocaine from the USA (N=157 base, N=88 HCl) were analyzed by headspace-gas chromatography-mass spectrometry (HS-GC-MS) to determine their solvent profiles. Each cocaine HCl sample was then converted to crack cocaine using the traditional crack production method and re-examined by HS-GC-MS. The resulting occluded solvent profiles were then compared to their original HCl solvent profiles. Analysis of the corresponding crack samples confirmed the same primary processing solvents found in the original HCl samples, but at reduced levels. Domestically seized crack samples also contained reduced levels of base-to-HCl conversion solvents. In contrast, analysis of South American crack samples confirmed the presence of low to high boiling hydrocarbons and no base-to-HCl conversion solvents. The presented study showed analysis of crack cocaine samples provides data on which processing solvents were originally utilized in the production of cocaine HCl in South America, prior to conversion to crack cocaine. Determination of processing solvents provides valuable information to the counter-drug intelligence community and assists the law enforcement community in determining cocaine distribution and trafficking routes throughout the world. Published 2014. This article is a U.S. Government work and is in the public domain in the USA.

  6. Improvement of bias-stability in amorphous-indium-gallium-zinc-oxide thin-film transistors by using solution-processed Y{sub 2}O{sub 3} passivation

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    An, Sungjin; Mativenga, Mallory; Kim, Youngoo

    2014-08-04

    We demonstrate back channel improvement of back-channel-etch amorphous-indium-gallium-zinc-oxide (a-IGZO) thin-film transistors by using solution-processed yttrium oxide (Y{sub 2}O{sub 3}) passivation. Two different solvents, which are acetonitrile (35%) + ethylene glycol (65%), solvent A and deionized water, solvent B are investigated for the spin-on process of the Y{sub 2}O{sub 3} passivation—performed after patterning source/drain (S/D) Mo electrodes by a conventional HNO{sub 3}-based wet-etch process. Both solvents yield devices with good performance but those passivated by using solvent B exhibit better light and bias stability. Presence of yttrium at the a-IGZO back interface, where it occupies metal vacancy sites, is confirmed by X-ray photoelectronmore » spectroscopy. The passivation effect of yttrium is more significant when solvent A is used because of the existence of more metal vacancies, given that the alcohol (65% ethylene glycol) in solvent A may dissolve the metal oxide (a-IGZO) through the formation of alkoxides and water.« less

  7. Morphology evolution in high-performance polymer solar cells processed from nonhalogenated solvent

    DOE PAGES

    Cai, Wanzhu; Liu, Peng; Jin, Yaocheng; ...

    2015-05-26

    A new processing protocol based on non-halogenated solvent and additive is developed to produce polymer solar cells with power conversion efficiencies better than those processed from commonly used halogenated solvent-additive pair. Morphology studies show that good performance correlates with a finely distributed nanomorphology with a well-defined polymer fibril network structure, which leads to balanced charge transport in device operation.

  8. Enzyme catalysis with small ionic liquid quantities.

    PubMed

    Fischer, Fabian; Mutschler, Julien; Zufferey, Daniel

    2011-04-01

    Enzyme catalysis with minimal ionic liquid quantities improves reaction rates, stereoselectivity and enables solvent-free processing. In particular the widely used lipases combine well with many ionic liquids. Demonstrated applications are racemate separation, esterification and glycerolysis. Minimal solvent processing is also an alternative to sluggish solvent-free catalysis. The method allows simplified down-stream processing, as only traces of ionic liquids have to be removed.

  9. Analyzing Environmental Policies for Chlorinated Solvents with a Model of Markets and Regulations

    DTIC Science & Technology

    1991-01-01

    electronics, aerospace, fabricated metal products, and dry cleaning depend heavily on chlorinated solvents in their production processes . For example...production processes . The second of the model’s components is a group of economic equations that represents all of the solvent substitutions in...Instead, the process for numerically specifying the substitution parameters involves eliciting expert judgments and then normalizing the parameters

  10. 1-Butyl-3-Methyl Imidazolium-based Ionic Liquids Explored as Potential Solvents for Lipid Processing

    USDA-ARS?s Scientific Manuscript database

    Due to global environmental concerns, there is increasing interest in replacing the volatile solvents currently used to process commodity plant lipids. Room-temperature molten salts are one type of media receiving great attention as a possible replacement of the typical organic solvent. Molten sal...

  11. Micro-Encapsulation of non-aqueous solvents for energy-efficient carbon capture

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Stolaroff, Joshua K; Ye, Congwang; Oakdale, James

    Here, we demonstrate micro-encapsulation of several promising designer solvents: an IL, PCIL, and CO2BOL. We develop custom polymers that cure by UV light in the presence of each solvent while maintaining high CO2 permeability. We use several new process strategies to accommodate the viscosity and phase changes. We then measure and compare the CO2 absorption rate and capacity as well as the multi-cycle performance of the encapsulated solvents. These results are compared with previous work on encapsulated sodium carbonate solution. The prospects for designer solvents to reduce the cost of post-combustion capture and the implications for process design with encapsulatedmore » solvents are discussed.« less

  12. Process-Improvement Cost Model for the Emergency Department.

    PubMed

    Dyas, Sheila R; Greenfield, Eric; Messimer, Sherri; Thotakura, Swati; Gholston, Sampson; Doughty, Tracy; Hays, Mary; Ivey, Richard; Spalding, Joseph; Phillips, Robin

    2015-01-01

    The objective of this report is to present a simplified, activity-based costing approach for hospital emergency departments (EDs) to use with Lean Six Sigma cost-benefit analyses. The cost model complexity is reduced by removing diagnostic and condition-specific costs, thereby revealing the underlying process activities' cost inefficiencies. Examples are provided for evaluating the cost savings from reducing discharge delays and the cost impact of keeping patients in the ED (boarding) after the decision to admit has been made. The process-improvement cost model provides a needed tool in selecting, prioritizing, and validating Lean process-improvement projects in the ED and other areas of patient care that involve multiple dissimilar diagnoses.

  13. Research in Stochastic Processes.

    DTIC Science & Technology

    1984-10-01

    Handbook of Statistics, Volume 5: Time Series in Time Domain, E.J. Hannan, P.R. Krishnaiah and M.M. Rao, eds., North Holland, 1984, to appear. 5. J.A...designs for time series." S. Cambanis, Handbook of Statistics. Volume 5: Time Series in Time Domain, E.J. Hannan, P.R. Krishnaiah and M.M. Rao, eds... Krishnaiah and M.M. Rao, eds., North Holland, 1984, to appear. 59. "Ergodic properties of stationary stable processes." S. Cambanis, C.D. Hardin, and A

  14. Microbial process for the preparation of acetic acid, as well as solvent for its extraction from the fermentation broth

    DOEpatents

    Gaddy, James L.; Clausen, Edgar C.; Ko, Ching-Whan; Wade, Leslie E.; Wikstrom, Carl V.

    2007-03-27

    A modified water-immiscible solvent useful in the extraction of acetic acid from aqueous streams is a substantially pure mixture of isomers of highly branched di-alkyl amines. Solvent mixtures formed of such a modified solvent with a desired co-solvent, preferably a low boiling hydrocarbon, are useful in the extraction of acetic acid from aqueous gaseous streams. An anaerobic microbial fermentation process for the production of acetic acid employs such solvents, under conditions which limit amide formation by the solvent and thus increase the efficiency of acetic acid recovery. Methods for the direct extraction of acetic acid and the extractive fermentation of acetic acid also employ the modified solvents and increase efficiency of acetic acid production. Such increases in efficiency are also obtained where the energy source for the microbial fermentation contains carbon dioxide and the method includes a carbon dioxide stripping step prior to extraction of acetic acid in solvent.

  15. Microbial process for the preparation of acetic acid, as well as solvent for its extraction from the fermentation broth

    DOEpatents

    Gaddy, James L.; Clausen, Edgar C.; Ko, Ching-Whan; Wade, Leslie E.; Wikstrom, Carl V.

    2004-06-22

    A modified water-immiscible solvent useful in the extraction of acetic acid from aqueous streams is a substantially pure mixture of isomers of highly branched di-alkyl amines. Solvent mixtures formed of such a modified solvent with a desired co-solvent, preferably a low boiling hydrocarbon, are useful in the extraction of acetic acid from aqueous gaseous streams. An anaerobic microbial fermentation process for the production of acetic acid employs such solvents, under conditions which limit amide formation by the solvent and thus increase the efficiency of acetic acid recovery. Methods for the direct extraction of acetic acid and the extractive fermentation of acetic acid also employ the modified solvents and increase efficiency of acetic acid production. Such increases in efficiency are also obtained where the energy source for the microbial fermentation contains carbon dioxide and the method includes a carbon dioxide stripping step prior to extraction of acetic acid in solvent.

  16. Process for hydrogenating coal and coal solvents

    DOEpatents

    Tarrer, Arthur R.; Shridharani, Ketan G.

    1983-01-01

    A novel process is described for the hydrogenation of coal by the hydrogenation of a solvent for the coal in which the hydrogenation of the coal solvent is conducted in the presence of a solvent hydrogenation catalyst of increased activity, wherein the hydrogenation catalyst is produced by reacting ferric oxide with hydrogen sulfide at a temperature range of 260.degree. C. to 315.degree. C. in an inert atmosphere to produce an iron sulfide hydrogenation catalyst for the solvent. Optimally, the reaction temperature is 275.degree. C. Alternately, the reaction can be conducted in a hydrogen atmosphere at 350.degree. C.

  17. Techno-economic assessment of hybrid extraction and distillation processes for furfural production from lignocellulosic biomass.

    PubMed

    Nhien, Le Cao; Long, Nguyen Van Duc; Kim, Sangyong; Lee, Moonyong

    2017-01-01

    Lignocellulosic biomass is one of the most promising alternatives for replacing mineral resources to overcome global warming, which has become the most important environmental issue in recent years. Furfural was listed by the National Renewable Energy Laboratory as one of the top 30 potential chemicals arising from biomass. However, the current production of furfural is energy intensive and uses inefficient technology. Thus, a hybrid purification process that combines extraction and distillation to produce furfural from lignocellulosic biomass was considered and investigated in detail to improve the process efficiency. This effective hybrid process depends on the extracting solvent, which was selected based on a comprehensive procedure that ranged from solvent screening to complete process design. Various solvents were first evaluated in terms of their extraction ability. Then, the most promising solvents were selected to study the separation feasibility. Eventually, processes that used the three best solvents (toluene, benzene, and butyl chloride) were designed and optimized in detail using Aspen Plus. Sustainability analysis was performed to evaluate these processes in terms of their energy requirements, total annual costs (TAC), and carbon dioxide (CO 2 ) emissions. The results showed that butyl chloride was the most suitable solvent for the hybrid furfural process because it could save 44.7% of the TAC while reducing the CO 2 emissions by 45.5% compared to the toluene process. In comparison with the traditional purification process using distillation, this suggested hybrid extraction/distillation process can save up to 19.2% of the TAC and reduce 58.3% total annual CO 2 emissions. Furthermore, a sensitivity analysis of the feed composition and its effect on the performance of the proposed hybrid system was conducted. Butyl chloride was found to be the most suitable solvent for the hybrid extraction/distillation process of furfural production. The proposed hybrid sequence was more favorable than the traditional distillation process when the methanol fraction of the feed stream was <3% and more benefit could be obtained when that fraction decreased.

  18. Understanding Solvent Manipulation of Morphology in Bulk-Heterojunction Organic Solar Cells.

    PubMed

    Chen, Yuxia; Zhan, Chuanlang; Yao, Jiannian

    2016-10-06

    Film morphology greatly influences the performance of bulk-heterojunction (BHJ)-structure-based solar cells. It is known that an interpenetrating bicontinuous network with nanoscale-separated donor and acceptor phases for charge transfer, an ordered molecular packing for exciton diffusion and charge transport, and a vertical compositionally graded structure for charge collection are prerequisites for achieving highly efficient BHJ organic solar cells (OSCs). Therefore, control of the morphology to obtain an ideal structure is a key problem. For this solution-processing BHJ system, the solvent participates fully in film processing. Its involvement is critical in modifying the nanostructure of BHJ films. In this review, we discuss the effects of solvent-related methods on the morphology of BHJ films, including selection of the casting solvent, solvent mixture, solvent vapor annealing, and solvent soaking. On the basis of a discussion on interaction strength and time between solvent and active materials, we believe that the solvent-morphology-performance relationship will be clearer and that solvent selection as a means to manipulate the morphology of BHJ films will be more rational. © 2016 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  19. Solvent extraction of diatomite

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Williams, W.

    1984-07-24

    There is provided a method of extracting hydrocarbons from a diatomite ore. The particle size of the ore is first reduced to form a processed ore. The processed ore is then mixed with a substantially irregular granular material to form an unstratified ore mixture having increased permeability to an extracting solvent. The unstratified ore mixture is then permeated with an extracting solvent to obtain a hydrocarbon-solvent stream from which hydrocarbons are subsequently separated. The irregular granular material may be sand.

  20. Improved Detection Technique for Solvent Rinse Cleanliness Verification

    NASA Technical Reports Server (NTRS)

    Hornung, S. D.; Beeson, H. D.

    2001-01-01

    The NASA White Sands Test Facility (WSTF) has an ongoing effort to reduce or eliminate usage of cleaning solvents such as CFC-113 and its replacements. These solvents are used in the final clean and cleanliness verification processes for flight and ground support hardware, especially for oxygen systems where organic contaminants can pose an ignition hazard. For the final cleanliness verification in the standard process, the equivalent of one square foot of surface area of parts is rinsed with the solvent, and the final 100 mL of the rinse is captured. The amount of nonvolatile residue (NVR) in the solvent is determined by weight after the evaporation of the solvent. An improved process of sampling this rinse, developed at WSTF, requires evaporation of less than 2 mL of the solvent to make the cleanliness verification. Small amounts of the solvent are evaporated in a clean stainless steel cup, and the cleanliness of the stainless steel cup is measured using a commercially available surface quality monitor. The effectiveness of this new cleanliness verification technique was compared to the accepted NVR sampling procedures. Testing with known contaminants in solution, such as hydraulic fluid, fluorinated lubricants, and cutting and lubricating oils, was performed to establish a correlation between amount in solution and the process response. This report presents the approach and results and discusses the issues in establishing the surface quality monitor-based cleanliness verification.

  1. Two-stage coal liquefaction without gas-phase hydrogen

    DOEpatents

    Stephens, H.P.

    1986-06-05

    A process is provided for the production of a hydrogen-donor solvent useful in the liquefaction of coal, wherein the water-gas shift reaction is used to produce hydrogen while simultaneously hydrogenating a donor solvent. A process for the liquefaction of coal using said solvent is also provided. The process enables avoiding the use of a separate water-gas shift reactor as well as high pressure equipment for liquefaction. 3 tabs.

  2. Improving timeliness for acute asthma care for paediatric ED patients using a nurse driven intervention: an interrupted time series analysis.

    PubMed

    Brown, Kathleen; Iqbal, Sabah; Sun, Su-Lin; Fritzeen, Jennifer; Chamberlain, James; Mullan, Paul C

    2016-01-01

    Asthma is the most common chronic paediatric disease treated in the emergency department (ED). Rapid corticosteroid administration is associated with improved outcomes, but our busy ED setting has made it challenging to achieve this goal. Our primary aim was to decrease the time to corticosteroid administration in a large, academic paediatric ED. We conducted an interrupted time series analysis for moderate to severe asthma exacerbations of one to 18 year old patients. A multidisciplinary team designed the intervention of a bedside nurse initiated administration of oral dexamethasone, to replace the prior system of a physician initiated order for oral prednisone. Our baseline and intervention periods were 12 month intervals. Our primary process measure was the time to corticosteroid administration. Other process measures included ED length of stay, admission rate, and rate of emesis. The balance measures included rate of return visits to the ED or clinic within five days, as well as the proportion of discharged patients who were admitted within five days. No special cause variation occurred in the baseline period. The mean time to corticosteroid administration decreased significantly, from 98 minutes in the baseline period to 59 minutes in the intervention period (p < 0.01), and showed special cause variation improvement within two months after the intervention using statistical process control methodology. We sustained the improvement and demonstrated a stable process. The intervention period had a significantly lower admission rate (p<0.01) and emesis rate (p<0.01), with no unforeseen harm to patients found with any of our balance measures. In summary, the introduction of a nurse initiated, standardized protocol for corticosteroid therapy for asthma exacerbations in a paediatric ED was associated with decreased time to corticosteroid administration, admission rates, and post-corticosteroid emesis.

  3. Progress in donor assisted coal liquefaction: Hydroaromatic compound formation

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Kottenstette, R.J.; Stephens, H.P.

    1993-12-31

    The role of hydrogen donor compounds in coal liquefaction has been extensively investigated since the mid 1960`s using model compounds and process derived hydrogen donor solvents. Our recent research and that of other investigators have shown that two model compounds in particular have great efficacy in solvating low rank coals. 1,2,3,10b tetrahydrofluoranthene (H{sub 4}Fl) and 1,2,3,6,7,8 hexahydropyrene (H{sub 6}Py) have been used to dissolve Wyodak coal to > 95% soluble material as measured by tetrahydrofuran (THF). Although these hydrogen donors are very effective, they may not be found in any significant concentrations in actual liquefaction process recycle solvents. Therefore, studiesmore » with process derived recycle materials are necessary to understand donor solvent chemistry. The objective of this paper is to present results of solvent hydrogenation experiments using heavy distillate solvents produced during testing at the Wilsonville Advanced Coal Liquefaction Test Facility. We evaluated the impact of hydrogenation conditions upon hydrogen donor formation in process derived distillates and compared these process derived solvents with the highly effective H{sub 4}Fl and H{sub 6}Py donors in coal liquefaction tests. This paper presents data on reaction conditions used for distillate hydrotreating and subsequent coal liquefaction, with an aim toward understanding the relationship between reaction conditions and donor solvent quality in recycle distillates.« less

  4. Emergency medicine: an operations management view.

    PubMed

    Soremekun, Olan A; Terwiesch, Christian; Pines, Jesse M

    2011-12-01

    Operations management (OM) is the science of understanding and improving business processes. For the emergency department (ED), OM principles can be used to reduce and alleviate the effects of crowding. A fundamental principle of OM is the waiting time formula, which has clear implications in the ED given that waiting time is fundamental to patient-centered emergency care. The waiting time formula consists of the activity time (how long it takes to complete a process), the utilization rate (the proportion of time a particular resource such a staff is working), and two measures of variation: the variation in patient interarrival times and the variation in patient processing times. Understanding the waiting time formula is important because it presents the fundamental parameters that can be managed to reduce waiting times and length of stay. An additional useful OM principle that is applicable to the ED is the efficient frontier. The efficient frontier compares the performance of EDs with respect to two dimensions: responsiveness (i.e., 1/wait time) and utilization rates. Some EDs may be "on the frontier," maximizing their responsiveness at their given utilization rates. However, most EDs likely have opportunities to move toward the frontier. Increasing capacity is a movement along the frontier and to truly move toward the frontier (i.e., improving responsiveness at a fixed capacity), we articulate three possible options: eliminating waste, reducing variability, or increasing flexibility. When conceptualizing ED crowding interventions, these are the major strategies to consider. © 2011 by the Society for Academic Emergency Medicine.

  5. Nonurgent patients in emergency departments: rational or irresponsible consumers? Perceptions of professionals and patients.

    PubMed

    Durand, Anne-Claire; Palazzolo, Sylvie; Tanti-Hardouin, Nicolas; Gerbeaux, Patrick; Sambuc, Roland; Gentile, Stéphanie

    2012-09-25

    For several decades, overcrowding in emergency departments (EDs) has been intensifying due to the increased number of patients seeking care in EDs. Demand growth is partly due to misuse of EDs by patients who seek care for nonurgent problems. This study explores the reasons why people with nonurgent complaints choose to come to EDs, and how ED health professionals perceive the phenomenon of "nonurgency". Semi-structured interviews were conducted in 10 EDs with 87 nonurgent patients and 34 health professionals. Interviews of patients revealed three themes: (1) fulfilled health care needs, (2) barriers to primary care providers (PCPs), and (3) convenience. Patients chose EDs as discerning health consumers: they preferred EDs because they had difficulties obtaining a rapid appointment. Access to technical facilities in EDs spares the patient from being overwhelmed with appointments with various specialists. Four themes were identified from the interviews of health professionals: (1) the problem of defining a nonurgent visit, (2) explanations for patients' use of EDs for nonurgent complaints, (3) consequences of nonurgent visits, and (4) solutions to counter this tendency. Studies on the underlying reasons patients opt for the ED, as well as on their decision-making process, are lacking. The present study highlighted discrepancies between the perceptions of ED patients and those of health professionals, with a special focus on patient behaviour. To explain the use of ED, health professionals based themselves on the acuity and urgency of medical problems, while patients focused on rational reasons to initiate care in the ED (accessibility to health care resources, and the context in which the medical problem occurred). In spite of some limitations due to the slightly outdated nature of our data, as well as the difficulty of categorizing nonurgent situations, our findings show the importance of conducting a detailed analysis of the demand for health care. Understanding it is crucial, as it is the main determining factor in the utilization of health care resources, and provides promising insights into the phenomenon of ED usage increase. For reforms to be successful, the process of decision-making for unscheduled patients will have to be thoroughly investigated.

  6. Using Lean Management to Reduce Emergency Department Length of Stay for Medicine Admissions.

    PubMed

    Allaudeen, Nazima; Vashi, Anita; Breckenridge, Julia S; Haji-Sheikhi, Farnoosh; Wagner, Sarah; Posley, Keith A; Asch, Steven M

    The practice of boarding admitted patients in the emergency department (ED) carries negative operational, clinical, and patient satisfaction consequences. Lean tools have been used to improve ED workflow. Interventions focused on reducing ED length of stay (LOS) for admitted patients are less explored. To evaluate a Lean-based initiative to reduce ED LOS for medicine admissions. Prospective quality improvement initiative performed at a single university-affiliated Department of Veterans Affairs (VA) medical center from February 2013 to February 2016. We performed a Lean-based multidisciplinary initiative beginning with a rapid process improvement workshop to evaluate current processes, identify root causes of delays, and develop countermeasures. Frontline staff developed standard work for each phase of the ED stay. Units developed a daily management system to reinforce, evaluate, and refine standard work. The primary outcome was the change in ED LOS for medicine admissions pre- and postintervention. ED LOS at the intervention site was compared with other similar VA facilities as controls over the same time period using a difference-in-differences approach. ED LOS for medicine admissions reduced 26.4%, from 8.7 to 6.4 hours. Difference-in-differences analysis showed that ED LOS for combined medicine and surgical admissions decreased from 6.7 to 6.0 hours (-0.7 hours, P = .003) at the intervention site compared with no change (5.6 hours, P = .2) at the control sites. We utilized Lean management to significantly reduce ED LOS for medicine admissions. Specifically, the development and management of standard work were key to sustaining these results.

  7. Extraction, scrub, and strip test results for the salt waste processing facility caustic side solvent extraction solvent example

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Peters, T. B.

    An Extraction, Scrub, and Strip (ESS) test was performed on a sample of Salt Waste Processing Facility (SWPF) Caustic-Side Solvent Extraction (CSSX) solvent and salt simulant to determine cesium distribution ratios (D(Cs)), and cesium concentration in the strip effluent (SE) and decontaminated salt solution (DSS) streams; this data will be used by Parsons to help determine if the solvent is qualified for use at the SWPF. The ESS test showed acceptable performance of the solvent for extraction, scrub, and strip operations. The extraction D(Cs) measured 12.9, exceeding the required value of 8. This value is consistent with results from previousmore » ESS tests using similar solvent formulations. Similarly, scrub and strip cesium distribution ratios fell within acceptable ranges.« less

  8. Applying Systems Engineering Reduces Radiology Transport Cycle Times in the Emergency Department.

    PubMed

    White, Benjamin A; Yun, Brian J; Lev, Michael H; Raja, Ali S

    2017-04-01

    Emergency department (ED) crowding is widespread, and can result in care delays, medical errors, increased costs, and decreased patient satisfaction. Simultaneously, while capacity constraints on EDs are worsening, contributing factors such as patient volume and inpatient bed capacity are often outside the influence of ED administrators. Therefore, systems engineering approaches that improve throughput and reduce waste may hold the most readily available gains. Decreasing radiology turnaround times improves ED patient throughput and decreases patient waiting time. We sought to investigate the impact of systems engineering science targeting ED radiology transport delays and determine the most effective techniques. This prospective, before-and-after analysis of radiology process flow improvements in an academic hospital ED was exempt from institutional review board review as a quality improvement initiative. We hypothesized that reorganization of radiology transport would improve radiology cycle time and reduce waste. The intervention included systems engineering science-based reorganization of ED radiology transport processes, largely using Lean methodologies, and adding no resources. The primary outcome was average transport time between study order and complete time. All patients presenting between 8/2013-3/2016 and requiring plain film imaging were included. We analyzed electronic medical record data using Microsoft Excel and SAS version 9.4, and we used a two-sample t-test to compare data from the pre- and post-intervention periods. Following the intervention, average transport time decreased significantly and sustainably. Average radiology transport time was 28.7 ± 4.2 minutes during the three months pre-intervention. It was reduced by 15% in the first three months (4.4 minutes [95% confidence interval [CI] 1.5-7.3]; to 24.3 ± 3.3 min, P=0.021), 19% in the following six months (5.4 minutes, 95% CI [2.7-8.2]; to 23.3 ± 3.5 min, P=0.003), and 26% one year following the intervention (7.4 minutes, 95% CI [4.8-9.9]; to 21.3 ± 3.1 min, P=0.0001). This result was achieved without any additional resources, and demonstrated a continual trend towards improvement. This innovation demonstrates the value of systems engineering science to increase efficiency in ED radiology processes. In this study, reorganization of the ED radiology transport process using systems engineering science significantly increased process efficiency without additional resource use.

  9. Applying Systems Engineering Reduces Radiology Transport Cycle Times in the Emergency Department

    PubMed Central

    White, Benjamin A.; Yun, Brian J.; Lev, Michael H.; Raja, Ali S.

    2017-01-01

    Introduction Emergency department (ED) crowding is widespread, and can result in care delays, medical errors, increased costs, and decreased patient satisfaction. Simultaneously, while capacity constraints on EDs are worsening, contributing factors such as patient volume and inpatient bed capacity are often outside the influence of ED administrators. Therefore, systems engineering approaches that improve throughput and reduce waste may hold the most readily available gains. Decreasing radiology turnaround times improves ED patient throughput and decreases patient waiting time. We sought to investigate the impact of systems engineering science targeting ED radiology transport delays and determine the most effective techniques. Methods This prospective, before-and-after analysis of radiology process flow improvements in an academic hospital ED was exempt from institutional review board review as a quality improvement initiative. We hypothesized that reorganization of radiology transport would improve radiology cycle time and reduce waste. The intervention included systems engineering science-based reorganization of ED radiology transport processes, largely using Lean methodologies, and adding no resources. The primary outcome was average transport time between study order and complete time. All patients presenting between 8/2013–3/2016 and requiring plain film imaging were included. We analyzed electronic medical record data using Microsoft Excel and SAS version 9.4, and we used a two-sample t-test to compare data from the pre- and post-intervention periods. Results Following the intervention, average transport time decreased significantly and sustainably. Average radiology transport time was 28.7 ± 4.2 minutes during the three months pre-intervention. It was reduced by 15% in the first three months (4.4 minutes [95% confidence interval [CI] 1.5–7.3]; to 24.3 ± 3.3 min, P=0.021), 19% in the following six months (5.4 minutes, 95% CI [2.7–8.2]; to 23.3 ± 3.5 min, P=0.003), and 26% one year following the intervention (7.4 minutes, 95% CI [4.8–9.9]; to 21.3 ± 3.1 min, P=0.0001). This result was achieved without any additional resources, and demonstrated a continual trend towards improvement. This innovation demonstrates the value of systems engineering science to increase efficiency in ED radiology processes. Conclusion In this study, reorganization of the ED radiology transport process using systems engineering science significantly increased process efficiency without additional resource use. PMID:28435492

  10. Tuning the properties of polyhydroxybutyrate films using acetic acid via solvent casting

    PubMed Central

    Anbukarasu, Preetam; Sauvageau, Dominic; Elias, Anastasia

    2015-01-01

    Biodegradable polyhydroxybutyrate (PHB) films were fabricated using acetic acid as an alternative to common solvents such as chloroform. The PHB films were prepared using a solvent casting process at temperatures ranging from 80 °C to 160 °C. The crystallinity, mechanical properties and surface morphology of the films cast at different temperatures were characterized and compared to PHB films cast using chloroform as a solvent. Results revealed that the properties of the PHB film varied considerably with solvent casting temperature. In general, samples processed with acetic acid at low temperatures had comparable mechanical properties to PHB cast using chloroform. This acetic acid based method is environmentally friendly, cost efficient and allows more flexible processing conditions and broader ranges of polymer properties than traditional methods. PMID:26640089

  11. Tuning the properties of polyhydroxybutyrate films using acetic acid via solvent casting

    NASA Astrophysics Data System (ADS)

    Anbukarasu, Preetam; Sauvageau, Dominic; Elias, Anastasia

    2015-12-01

    Biodegradable polyhydroxybutyrate (PHB) films were fabricated using acetic acid as an alternative to common solvents such as chloroform. The PHB films were prepared using a solvent casting process at temperatures ranging from 80 °C to 160 °C. The crystallinity, mechanical properties and surface morphology of the films cast at different temperatures were characterized and compared to PHB films cast using chloroform as a solvent. Results revealed that the properties of the PHB film varied considerably with solvent casting temperature. In general, samples processed with acetic acid at low temperatures had comparable mechanical properties to PHB cast using chloroform. This acetic acid based method is environmentally friendly, cost efficient and allows more flexible processing conditions and broader ranges of polymer properties than traditional methods.

  12. Organic solvent regeneration of granular activated carbon

    NASA Astrophysics Data System (ADS)

    Cross, W. H.; Suidan, M. T.; Roller, M. A.; Kim, B. R.; Gould, J. P.

    1982-09-01

    The use of activated carbon for the treatment of industrial waste-streams was shown to be an effective treatment. The high costs associated with the replacement or thermal regeneration of the carbon have prohibited the economic feasibility of this process. The in situ solvent regeneration of activated carbon by means of organic solvent extraction was suggested as an economically alternative to thermal regeneration. The important aspects of the solvent regeneration process include: the physical and chemical characteristics of the adsorbent, the pore size distribution and energy of adsorption associated with the activated carbon; the degree of solubility of the adsorbate in the organic solvent; the miscibility of the organic solvent in water; and the temperature at which the generation is performed.

  13. Free Enthalpy Differences between α-, π-, and 310-Helices of an Atomic Level Fine-Grained Alanine Deca-Peptide Solvated in Supramolecular Coarse-Grained Water.

    PubMed

    Lin, Zhixiong; Riniker, Sereina; van Gunsteren, Wilfred F

    2013-03-12

    Atomistic molecular dynamics simulations of peptides or proteins in aqueous solution are still limited to the multi-nanosecond time scale and multi-nanometer range by computational cost. Combining atomic solutes with a supramolecular solvent model in hybrid fine-grained/coarse-grained (FG/CG) simulations allows atomic detail in the region of interest while being computationally more efficient. We used enveloping distribution sampling (EDS) to calculate the free enthalpy differences between different helical conformations, i.e., α-, π-, and 310-helices, of an atomic level FG alanine deca-peptide solvated in a supramolecular CG water solvent. The free enthalpy differences obtained show that by replacing the FG solvent by the CG solvent, the π-helix is destabilized with respect to the α-helix by about 2.5 kJ mol(-1), and the 310-helix is stabilized with respect to the α-helix by about 9 kJ mol(-1). In addition, the dynamics of the peptide becomes faster. By introducing a FG water layer of 0.8 nm around the peptide, both thermodynamic and dynamic properties are recovered, while the hybrid FG/CG simulations are still four times more efficient than the atomistic simulations, even when the cutoff radius for the nonbonded interactions is increased from 1.4 to 2.0 nm. Hence, the hybrid FG/CG model, which yields an appropriate balance between reduced accuracy and enhanced computational speed, is very suitable for molecular dynamics simulation investigations of biomolecules.

  14. Processes for preparing carbon fibers using sulfur trioxide in a halogenated solvent

    DOEpatents

    Patton, Jasson T.; Barton, Bryan E.; Bernius, Mark T.; Chen, Xiaoyun; Hukkanen, Eric J.; Rhoton, Christina A.; Lysenko, Zenon

    2015-12-29

    Disclosed here are processes for preparing carbonized polymers (preferably carbon fibers), comprising sulfonating a polymer with a sulfonating agent that comprises SO.sub.3 dissolved in a solvent to form a sulfonated polymer; treating the sulfonated polymer with a heated solvent, wherein the temperature of the solvent is at least 95.degree. C.; and carbonizing the resulting product by heating it to a temperature of 500-3000.degree. C. Carbon fibers made according to these methods are also disclosed herein.

  15. Testing of electroformed deposited iridium/powder metallurgy rhenium rockets

    NASA Technical Reports Server (NTRS)

    Reed, Brian D.; Dickerson, Robert

    1996-01-01

    High-temperature, oxidation-resistant chamber materials offer the thermal margin for high performance and extended lifetimes for radiation-cooled rockets. Rhenium (Re) coated with iridium (Ir) allow hours of operation at 2200 C on Earth-storable propellants. One process for manufacturing Ir/Re rocket chambers is the fabrication of Re substrates by powder metallurgy (PM) and the application of Ir coatings by using electroformed deposition (ED). ED Ir coatings, however, have been found to be porous and poorly adherent. The integrity of ED Ir coatings could be improved by densification after the electroforming process. This report summarizes the testing of two 22-N, ED Ir/PM Re rocket chambers that were subjected to post-deposition treatments in an effort to densify the Ir coating. One chamber was vacuum annealed, while the other chamber was subjected to hot isostatic pressure (HIP). The chambers were tested on gaseous oxygen/gaseous hydrogen propellants, at mixture ratios that simulated the oxidizing environments of Earth-storable propellants. ne annealed ED Ir/PM Re chamber was tested for a total of 24 firings and 4.58 hr at a mixture ratio of 4.2. After only 9 firings, the annealed ED Ir coating began to blister and spall upstream of the throat. The blistering and spalling were similar to what had been experienced with unannealed, as-deposited ED Ir coatings. The HIP ED Ir/PM Re chamber was tested for a total of 91 firings and 11.45 hr at mixture ratios of 3.2 and 4.2. The HIP ED Ir coating remained adherent to the Re substrate throughout testing; there were no visible signs of coating degradation. Metallography revealed, however, thinning of the HIP Ir coating and occasional pores in the Re layer upstream of the throat. Pinholes in the Ir coating may have provided a path for oxidation of the Re substrate at these locations. The HIP ED Ir coating proved to be more effective than vacuum annealed and as-deposited ED Ir. Further densification is still required to match the integrity of chemically vapor deposited Ir coatings. Despite this, the successful long duration testing of the HIP ED Ir chamber, in an oxidizing environment comparable to Earth-storable propellants, demonstrated the viability of this Ir/Re rocket fabrication process.

  16. Time phased alternate blending of feed coals for liquefaction

    DOEpatents

    Schweigharett, Frank; Hoover, David S.; Garg, Diwaker

    1985-01-01

    The present invention is directed to a method for reducing process performance excursions during feed coal or process solvent changeover in a coal hydroliquefaction process by blending of feedstocks or solvents over time. ,

  17. Solvent wash solution

    DOEpatents

    Neace, J.C.

    1984-03-13

    A process is claimed for removing diluent degradation products from a solvent extraction solution, which has been used to recover uranium and plutonium from spent nuclear fuel. A wash solution and the solvent extraction solution are combined. The wash solution contains (a) water and (b) up to about, and including, 50 vol % of at least one-polar water-miscible organic solvent based on the total volume of the water and the highly-polar organic solvent. The wash solution also preferably contains at least one inorganic salt. The diluent degradation products dissolve in the highly-polar organic solvent and the organic solvent extraction solvent do not dissolve in the highly-polar organic solvent. The highly-polar organic solvent and the extraction solvent are separated.

  18. Solvent wash solution

    DOEpatents

    Neace, James C.

    1986-01-01

    Process for removing diluent degradation products from a solvent extraction solution, which has been used to recover uranium and plutonium from spent nuclear fuel. A wash solution and the solvent extraction solution are combined. The wash solution contains (a) water and (b) up to about, and including, 50 volume percent of at least one-polar water-miscible organic solvent based on the total volume of the water and the highly-polar organic solvent. The wash solution also preferably contains at least one inorganic salt. The diluent degradation products dissolve in the highly-polar organic solvent and the organic solvent extraction solvent do not dissolve in the highly-polar organic solvent. The highly-polar organic solvent and the extraction solvent are separated.

  19. Development of balanced key performance indicators for emergency departments strategic dashboards following analytic hierarchical process.

    PubMed

    Safdari, Reza; Ghazisaeedi, Marjan; Mirzaee, Mahboobeh; Farzi, Jebrail; Goodini, Azadeh

    2014-01-01

    Dynamic reporting tools, such as dashboards, should be developed to measure emergency department (ED) performance. However, choosing an effective balanced set of performance measures and key performance indicators (KPIs) is a main challenge to accomplish this. The aim of this study was to develop a balanced set of KPIs for use in ED strategic dashboards following an analytic hierarchical process. The study was carried out in 2 phases: constructing ED performance measures based on balanced scorecard perspectives and incorporating them into analytic hierarchical process framework to select the final KPIs. The respondents placed most importance on ED internal processes perspective especially on measures related to timeliness and accessibility of care in ED. Some measures from financial, customer, and learning and growth perspectives were also selected as other top KPIs. Measures of care effectiveness and care safety were placed as the next priorities too. The respondents placed least importance on disease-/condition-specific "time to" measures. The methodology can be presented as a reference model for development of KPIs in various performance related areas based on a consistent and fair approach. Dashboards that are designed based on such a balanced set of KPIs will help to establish comprehensive performance measurements and fair benchmarks and comparisons.

  20. Re-construction layer effect of LiNi0.8Co0.15Mn0.05O2 with solvent evaporation process

    NASA Astrophysics Data System (ADS)

    Park, Kwangjin; Park, Jun-Ho; Hong, Suk-Gi; Choi, Byungjin; Heo, Sung; Seo, Seung-Woo; Min, Kyoungmin; Park, Jin-Hwan

    2017-03-01

    The solvent evaporation method on the structural changes and surface chemistry of the cathode and the effect of electrochemical performance of Li1.0Ni0.8Co0.15Mn0.05O2 (NCM) has been investigated. After dissolving of Li residuals using minimum content of solvent in order to minimize the damage of pristine material and the evaporation time, the solvent was evaporated without filtering and remaining powder was re-heated at 700 °C in oxygen environment. Two kinds of solvent, de-ionized water and diluted nitric acid, were used as a solvent. The almost 40% of Li residuals were removed using solvent evaporation method. The NCM sample after solvent evaporation process exhibited an increase in the initial capacity (214.3 mAh/g) compared to the pristine sample (207.4 mAh/g) at 0.1C because of enhancement of electric conductivity caused by decline of Li residuals. The capacity retention of NCM sample after solvent evaporation process (96.0% at the 50th cycle) was also improved compared to that of the pristine NCM sample (90.6% at the 50th cycle). The uniform Li residual layer after solvent treated and heat treatment acted like a coating layer, leading to enhance the cycle performance. The NCM sample using diluted nitric acid showed better performance than that using de-ionized water.

  1. ED QUEST: A Process for Linking Environmental Changes with Strategic Management. [Revised].

    ERIC Educational Resources Information Center

    Morrison, James L.; Mecca, Thomas V.

    Educational Quick Environmental Scanning Technique (ED QUEST) is a process designed to identify emerging issues and events that indicate potential threats and opportunities to educational organizations, to analyze the probable impact of these variables on the organization, and to facilitate the development of appropriate organizational strategies.…

  2. Institutionalizing Environmental Scanning in the ED QUEST Process.

    ERIC Educational Resources Information Center

    Morrison, James L.

    An environmental scanning system is structured to identify and evaluate trends, events, and emerging issues. QUEST represents the quick environmental scanning technique, and an ED QUEST process enables an educational organization to clarify its future and define its options. This paper describes how an educational organization can establish an…

  3. Assessment of central auditory processing in a group of workers exposed to solvents.

    PubMed

    Fuente, Adrian; McPherson, Bradley; Muñoz, Verónica; Pablo Espina, Juan

    2006-12-01

    Despite having normal hearing thresholds and speech recognition thresholds, results for central auditory tests were abnormal in a group of workers exposed to solvents. Workers exposed to solvents may have difficulties in everyday listening situations that are not related to a decrement in hearing thresholds. A central auditory processing disorder may underlie these difficulties. To study central auditory processing abilities in a group of workers occupationally exposed to a mix of organic solvents. Ten workers exposed to a mix of organic solvents and 10 matched non-exposed workers were studied. The test battery comprised pure-tone audiometry, tympanometry, acoustic reflex measurement, acoustic reflex decay, dichotic digit, pitch pattern sequence, masking level difference, filtered speech, random gap detection and hearing-in-noise tests. All the workers presented normal hearing thresholds and no signs of middle ear abnormalities. Workers exposed to solvents had lower results in comparison with the control group and previously reported normative data, in the majority of the tests.

  4. Effects of the internal friction and the solvent quality on the dynamics of a polymer chain closure.

    PubMed

    Yu, Wancheng; Luo, Kaifu

    2015-03-28

    Using 3D Langevin dynamics simulations, we investigate the effects of the internal friction and the solvent quality on the dynamics of a polymer chain closure. We show that the chain closure in good solvents is a purely diffusive process. By extrapolation to zero solvent viscosity, we find that the internal friction of a chain plays a non-ignorable role in the dynamics of the chain closure. When the solvent quality changes from good to poor, the mean closure time τc decreases by about 1 order of magnitude for the chain length 20 ≤ N ≤ 100. Furthermore, τc has a minimum as a function of the solvent quality. With increasing the chain length N, the minimum of τc occurs at a better solvent. Finally, the single exponential distributions of the closure time in poor solvents suggest that the negative excluded volume of segments does not alter the nearly Poisson statistical characteristics of the process of the chain closure.

  5. Use of once-through treat gas to remove the heat of reaction in solvent hydrogenation processes

    DOEpatents

    Nizamoff, Alan J.

    1980-01-01

    In a coal liquefaction process wherein feed coal is contacted with molecular hydrogen and a hydrogen-donor solvent in a liquefaction zone to form coal liquids and vapors and coal liquids in the solvent boiling range are thereafter hydrogenated to produce recycle solvent and liquid products, the improvement which comprises separating the effluent from the liquefaction zone into a hot vapor stream and a liquid stream; cooling the entire hot vapor stream sufficiently to condense vaporized liquid hydrocarbons; separating condensed liquid hydrocarbons from the cooled vapor; fractionating the liquid stream to produce coal liquids in the solvent boiling range; dividing the cooled vapor into at least two streams; passing the cooling vapors from one of the streams, the coal liquids in the solvent boiling range, and makeup hydrogen to a solvent hydrogenation zone, catalytically hydrogenating the coal liquids in the solvent boiling range and quenching the hydrogenation zone with cooled vapors from the other cooled vapor stream.

  6. Extraction, scrub, and strip test results for the solvent transfer to salt waste processing facility

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Peters, T.

    The Savannah River National Laboratory (SRNL) prepared approximately 240 gallons of Caustic-Side Solvent Extraction (CSSX) solvent for use at the Salt Waste Processing Facility (SWPF). An Extraction, Scrub, and Strip (ESS) test was performed on a sample of the prepared solvent using a salt solution prepared by Parsons to determine cesium distribution ratios (D(Cs)), and cesium concentration in the strip effluent (SE) and decontaminated salt solution (DSS) streams. This data will be used by Parsons to help qualify the solvent for use at the SWPF. The ESS test showed acceptable performance of the solvent for extraction, scrub, and strip operations.more » The extraction D(Cs) measured 15.5, exceeding the required value of 8. This value is consistent with results from previous ESS tests using similar solvent formulations. Similarly, scrub and strip cesium distribution ratios fell within acceptable ranges.« less

  7. Novel polyoxometalate silica nano-sized spheres: efficient catalysts for olefin oxidation and the deep desulfurization process.

    PubMed

    Nogueira, Lucie S; Ribeiro, Susana; Granadeiro, Carlos M; Pereira, Eulália; Feio, Gabriel; Cunha-Silva, Luís; Balula, Salete S

    2014-07-07

    A novel method to prepare silica nano-sized particles incorporating polyoxometalates was developed leading to a new efficient heterogeneous oxidative catalyst. Zinc-substituted polyoxotungstate [PW11Zn(H2O)O39](5-) (PW11Zn) was encapsulated into silica nanoparticles using a cross-linked organic-inorganic core, performed through successive spontaneous reactions in water. The potassium salt of PW11Zn and the composite formed, PW11Zn-APTES@SiO2, were characterized by a myriad of solid-state methods such as FT-IR, FT-Raman, (31)P and (13)C CP/MAS solid-state NMR, elemental analysis and SEM-EDS, confirming the integrity of the PW11Zn structure immobilized in the silica nanoparticles. The new composite has shown to be a versatile catalyst for the oxidation of olefins and also to catalyze the desulfurization of a model oil using H2O2 as the oxidant and acetonitrile as the solvent. The novel composite material was capable of being recycled without significant loss of activity and maintaining its structural stability for consecutive desulfurization and olefin oxidative cycles.

  8. Spectroscopic and electrochemical characterization of some Schiff base metal complexes containing benzoin moiety.

    PubMed

    El-Shahawi, M S; Al-Jahdali, M S; Bashammakh, A S; Al-Sibaai, A A; Nassef, H M

    2013-09-01

    The ligation behavior of bis-benzoin ethylenediamine (B2ED) and benzoin thiosemicarbazone (BTS) Schiff bases towards Ru(3+), Rh(3+), Pd(2+), Ni(2+) and Cu(2+) were determined. The bond length of M-N and spectrochemical parameters (10Dq, β, B and LFSE) of the complexes were evaluated. The redox characteristics of selected complexes were explored by cyclic voltammetry (CV) at Pt working electrode in non aqueous solvents. Au mesh (100 w/in.) optically transparent thin layer electrode (OTTLE) was also used for recording thin layer CV for selected Ru complex. Oxidation of some complexes occurs in a consecutive chemical reaction of an EC type mechanism. The characteristics of electron transfer process of the couples M(2+)/M(3+) and M(3+)/M(4+) (M=Ru(3+), Rh(3+)) and the stability of the complexes towards oxidation and/or reduction were assigned. The nature of the electroactive species and reduction mechanism of selected electrode couples were assigned. Copyright © 2013 The Authors. Published by Elsevier B.V. All rights reserved.

  9. Microbial process for the preparation of acetic acid as well as solvent for its extraction from the fermentation broth

    DOEpatents

    Gaddy, James L.; Clausen, Edgar C.; Ko, Ching-Whan; Wade, Leslie E.; Wikstrom, Carl V.

    2006-07-11

    A modified water-immiscible solvent useful in the extraction of acetic acid from aqueous streams is a substantially pure mixture of isomers of highly branched di-alkyl amines. This solvent is substantially devoid of mono-alkyl amines and alcohols. Solvent mixtures formed of such a modified solvent with a desired cosolvent, preferably a low boiling hydrocarbon which forms an azeotrope with water are useful in the extraction of acetic acid from aqueous gaseous streams. An anaerobic microbial fermentation process for the production of acetic acid employs such solvents, under conditions which limit amide formation by the solvent and thus increase the efficiency of acetic acid recovery. Methods for the direct extraction of acetic acid and the extractive fermentation of acetic acid also employ the modified solvents and increase efficiency of acetic acid production. Such increases in efficiency are also obtained where the energy source for the microbial fermentation contains carbon dioxide and the method includes a carbon dioxide stripping step prior to extraction of acetic acid in solvent.

  10. Microbial process for the preparation of acetic acid as well as solvent for its extraction from the fermentation broth

    DOEpatents

    Gaddy, James L.; Clausen, Edgar C.; Ko, Ching-Whan; Wade, Leslie E.; Wikstrom, Carl V.

    2002-01-01

    A modified water-immiscible solvent useful in the extraction of acetic acid from aqueous streams is a substantially pure mixture of isomers of highly branched di-alkyl amines. This solvent is substantially devoid of mono-alkyl amines and alcohols. Solvent mixtures formed of such a modified solvent with a desired cosolvent, preferably a low boiling hydrocarbon which forms an azeotrope with water are useful in the extraction of acetic acid from aqueous gaseous streams. An anaerobic microbial fermentation process for the production of acetic acid employs such solvents, under conditions which limit amide formation by the solvent and thus increase the efficiency of acetic acid recovery. Methods for the direct extraction of acetic acid and the extractive fermentation of acetic acid also employ the modified solvents and increase efficiency of acetic acid production. Such increases in efficiency are also obtained where the energy source for the microbial fermentation contains carbon dioxide and the method includes a carbon dioxide stripping step prior to extraction of acetic acid in solvent.

  11. Three-dimensional rotation electron diffraction: software RED for automated data collection and data processing

    PubMed Central

    Wan, Wei; Sun, Junliang; Su, Jie; Hovmöller, Sven; Zou, Xiaodong

    2013-01-01

    Implementation of a computer program package for automated collection and processing of rotation electron diffraction (RED) data is described. The software package contains two computer programs: RED data collection and RED data processing. The RED data collection program controls the transmission electron microscope and the camera. Electron beam tilts at a fine step (0.05–0.20°) are combined with goniometer tilts at a coarse step (2.0–3.0°) around a common tilt axis, which allows a fine relative tilt to be achieved between the electron beam and the crystal in a large tilt range. An electron diffraction (ED) frame is collected at each combination of beam tilt and goniometer tilt. The RED data processing program processes three-dimensional ED data generated by the RED data collection program or by other approaches. It includes shift correction of the ED frames, peak hunting for diffraction spots in individual ED frames and identification of these diffraction spots as reflections in three dimensions. Unit-cell parameters are determined from the positions of reflections in three-dimensional reciprocal space. All reflections are indexed, and finally a list with hkl indices and intensities is output. The data processing program also includes a visualizer to view and analyse three-dimensional reciprocal lattices reconstructed from the ED frames. Details of the implementation are described. Data collection and data processing with the software RED are demonstrated using a calcined zeolite sample, silicalite-1. The structure of the calcined silicalite-1, with 72 unique atoms, could be solved from the RED data by routine direct methods. PMID:24282334

  12. Three-dimensional rotation electron diffraction: software RED for automated data collection and data processing.

    PubMed

    Wan, Wei; Sun, Junliang; Su, Jie; Hovmöller, Sven; Zou, Xiaodong

    2013-12-01

    Implementation of a computer program package for automated collection and processing of rotation electron diffraction (RED) data is described. The software package contains two computer programs: RED data collection and RED data processing. The RED data collection program controls the transmission electron microscope and the camera. Electron beam tilts at a fine step (0.05-0.20°) are combined with goniometer tilts at a coarse step (2.0-3.0°) around a common tilt axis, which allows a fine relative tilt to be achieved between the electron beam and the crystal in a large tilt range. An electron diffraction (ED) frame is collected at each combination of beam tilt and goniometer tilt. The RED data processing program processes three-dimensional ED data generated by the RED data collection program or by other approaches. It includes shift correction of the ED frames, peak hunting for diffraction spots in individual ED frames and identification of these diffraction spots as reflections in three dimensions. Unit-cell parameters are determined from the positions of reflections in three-dimensional reciprocal space. All reflections are indexed, and finally a list with hkl indices and intensities is output. The data processing program also includes a visualizer to view and analyse three-dimensional reciprocal lattices reconstructed from the ED frames. Details of the implementation are described. Data collection and data processing with the software RED are demonstrated using a calcined zeolite sample, silicalite-1. The structure of the calcined silicalite-1, with 72 unique atoms, could be solved from the RED data by routine direct methods.

  13. Excessive daytime sleepiness in Parkinson disease: a SPECT study.

    PubMed

    Matsui, Hideaki; Nishinaka, Kazuto; Oda, Masaya; Hara, Narihiro; Komatsu, Kenichi; Kubori, Tamotsu; Udaka, Fukashi

    2006-07-01

    The underlying pathologic mechanism of excessive daytime sleepiness (EDS) in Parkinson disease and the relative contributions of brain function to this process are poorly understood. We compared brain perfusion images between patients with Parkinson disease and EDS and those without EDS using n-isopropyl-p-1231 iodoamphetamine single photon emission computed tomography. Clinical study. Sumitomo Hospital. Thirteen patients with Parkinson disease with EDS (EDS group) and 27 patients with Parkinson disease without EDS (no-EDS group) were studied. Whether or not each case had EDS was determined according to the response to the Epworth Sleepiness Scale: patients with an Epworth Sleepiness Scale score > or = 10 were included in the EDS group, and patients with an Epworth Sleepiness Scale score < or = 9 were included in the no-EDS group. There were significant hypoperfusions in the left parietal and temporal association cortex in the EDS group. In the multivariable logistic regression model, attention and decreased regional cerebral blood flow of the left parietal association cortex and right caudate and increased regional cerebral blood flow of the right thalamus were the independent and significant factors. The cortical hypofunction relative to hyperfunction of the brain stem may relate to EDS in Parkinson disease. This is the first imaging study about EDS in Parkinson disease, and further studies are required.

  14. Molecular dynamics simulation of highly charged proteins: Comparison of the particle-particle particle-mesh and reaction field methods for the calculation of electrostatic interactions

    PubMed Central

    Gargallo, Raimundo; Hünenberger, Philippe H.; Avilés, Francesc X.; Oliva, Baldomero

    2003-01-01

    Molecular dynamics (MD) simulations of the activation domain of porcine procarboxypeptidase B (ADBp) were performed to examine the effect of using the particle-particle particle-mesh (P3M) or the reaction field (RF) method for calculating electrostatic interactions in simulations of highly charged proteins. Several structural, thermodynamic, and dynamic observables were derived from the MD trajectories, including estimated entropies and solvation free energies and essential dynamics (ED). The P3M method leads to slightly higher atomic positional fluctuations and deviations from the crystallographic structure, along with somewhat lower values of the total energy and solvation free energy. However, the ED analysis of the system leads to nearly identical results for both simulations. Because of the strong similarity between the results, both methods appear well suited for the simulation of highly charged globular proteins in explicit solvent. However, the lower computational demand of the RF method in the present implementation represents a clear advantage over the P3M method. PMID:14500874

  15. Toxic hepatitis in occupational exposure to solvents

    PubMed Central

    Malaguarnera, Giulia; Cataudella, Emanuela; Giordano, Maria; Nunnari, Giuseppe; Chisari, Giuseppe; Malaguarnera, Mariano

    2012-01-01

    The liver is the main organ responsible for the metabolism of drugs and toxic chemicals, and so is the primary target organ for many organic solvents. Work activities with hepatotoxins exposures are numerous and, moreover, organic solvents are used in various industrial processes. Organic solvents used in different industrial processes may be associated with hepatotoxicity. Several factors contribute to liver toxicity; among these are: species differences, nutritional condition, genetic factors, interaction with medications in use, alcohol abuse and interaction, and age. This review addresses the mechanisms of hepatotoxicity. The main pathogenic mechanisms responsible for functional and organic damage caused by solvents are: inflammation, dysfunction of cytochrome P450, mitochondrial dysfunction and oxidative stress. The health impact of exposure to solvents in the workplace remains an interesting and worrying question for professional health work. PMID:22719183

  16. Two-stage coal liquefaction process

    DOEpatents

    Skinner, Ronald W.; Tao, John C.; Znaimer, Samuel

    1985-01-01

    An improved SRC-I two-stage coal liquefaction process which improves the product slate is provided. Substantially all of the net yield of 650.degree.-850.degree. F. heavy distillate from the LC-Finer is combined with the SRC process solvent, substantially all of the net 400.degree.-650.degree. F. middle distillate from the SRC section is combined with the hydrocracker solvent in the LC-Finer, and the initial boiling point of the SRC process solvent is increased sufficiently high to produce a net yield of 650.degree.-850.degree. F. heavy distillate of zero for the two-stage liquefaction process.

  17. Terra-Kleen Response Group, Inc. Solvent Extraction Technology Rapid Commercialization Initiative Report

    EPA Science Inventory

    Terra-Kleen Response Group Inc. (Terra-Kleen), has commercialized a solvent extraction technology that uses a proprietary extraction solvent to transfer organic constituents from soil to a liquid phase in a batch process at ambient temperatures. The proprietary solvent has a rel...

  18. The rise of eating disorders in Asia: a review.

    PubMed

    Pike, Kathleen M; Dunne, Patricia E

    2015-01-01

    Once concentrated among adolescent Caucasian females in high-income Western countries, today, eating disorders (EDs) are truly global. Building upon previous work describing the rise of EDs among cultures in transition, we contextualize the emergence of EDs in Asia by locating this development within the broader discourse about the processes of change that have radically transformed Asian societies over the last three decades. By identifying where EDs are emerging in the region, and by examining their particular expression, our aim is to explicate a fuller story of the relationship between culture and eating disorders. Much of the discussion of EDs in non-Western societies is predicated upon the assumption that an increase in EDs is the by-product of "Westernization", the term used to describe the process by which increased cultural contact with the West results in the transmission of so-called 'Western' ideas and cultural norms to a non-Western culture. While the Westernization literature represents a historical anchor in our understanding of EDs in Asia, we propose that this analysis is incomplete in that societal change in the form of industrialization and urbanization occurring independently from, or in tandem with, "Western" influence are critical factors contributing to the rise of EDs in Asia. Further, our review of eating disorders in Asia suggests that an understanding of the diversity and distinctiveness of the individual countries and cultures that comprise 'Asia' is crucial to understanding the emergence and rise of EDs across this vast region, suggesting that eating disorders are not culture-bound or culture-specific, but rather culture-reactive. Taking into account both the historical influence of Western culture and the more contemporary effects of Asian industrialization and urbanization, key distinctions among respective Asian cultures expands our understanding of the development and expression of EDs globally.

  19. System and process for capture of H.sub.2S from gaseous process streams and process for regeneration of the capture agent

    DOEpatents

    Heldenbrant, David J; Koech, Phillip K; Rainbolt, James E; Bearden, Mark D; Zheng, Feng

    2014-02-18

    A system and process are disclosed for selective removal and recovery of H.sub.2S from a gaseous volume, e.g., from natural gas. Anhydrous organic, sorbents chemically capture H.sub.2S gas to form hydrosulfide salts. Regeneration of the capture solvent involves addition of an anti-solvent that releases the captured H.sub.2S gas from the capture sorbent. The capture sorbent and anti-solvent are reactivated for reuse, e.g., by simple distillation.

  20. Working Together to Connect Care: a metropolitan tertiary emergency department and community care program.

    PubMed

    Harcourt, Debra; McDonald, Clancy; Cartlidge-Gann, Leonie; Burke, John

    2017-03-02

    Objective Frequent attendance by people to an emergency department (ED) is a global concern. A collaborative partnership between an ED and the primary and community healthcare sectors has the potential to improve care for the person who frequently attends the ED. The aims of the Working Together to Connect Care program are to decrease the number of presentations by providing focused community support and to integrate all healthcare services with the goal of achieving positive, patient-centred and directed outcomes. Methods A retrospective analysis of ED data for 2014 and 2015 was used to ascertain the characteristics of the potential program cohort. The definition used to identify a 'frequent attendee' was more than four presentations to an ED in 1 month. This analysis was used to develop the processes now known as the Working Together to Connect Care program. This program includes participant identification by applying the definition, flagging of potential participants in the ED IT system, case review and referral to community services by ED staff, case conferencing facilitated within the ED and individualised, patient centred case management provided by government and non-government community services. Results Two months after the date of commencement of the Working Together to Connect Care program there are 31 active participants in the program: 10 are on the Mental Health pathway, and one is on the No Consent pathway. On average there are three people recruited to the program every week. The establishment of a new program for supporting frequent attendees of an ED has had its challenges. Identifying systems that support people in their community has been an early positive outcome of this project. Conclusion It is expected that data regarding the number of ED presentations, potential fiscal savings and client outcomes will be available in 2017. What is known about the topic? Frequent attendance at EDs is a global issue and although the number of 'super users' is small compared with non-frequent users, the presentations are high. People in the frequent attendee group will often seek care from multiple EDs for, in the main, mental health issues and substance abuse. Furthermore, frequent ED users are vulnerable and experience higher mortality, hospital admissions and out-patient visits than non-frequent users. Aggressive and assertive outreach, intense coordination of services by integrated care teams, and the need for non-medical resources, such as supportive housing, have positive outcomes for this group of people. What does this paper add? This study uses international research findings in an Australian setting to provide a testing of the generalisability of an assertive and collaborative ED and community case management approach for supporting people who frequent a metropolitan ED. What are the implications for practitioners? The chronicling of a process undertaken to affect change in a health care setting supports practitioners when developing processes for this cohort across different ED contexts.

  1. Low-Cost Aqueous Coal Desulfurization

    NASA Technical Reports Server (NTRS)

    Kalvinskas, J. J.; Vasilakos, N.; Corcoran, W. H.; Grohmann, K.; Rohatgi, N. K.

    1982-01-01

    Water-based process for desulfurizing coal not only eliminates need for costly organic solvent but removes sulfur more effectively than an earlier solvent-based process. New process could provide low-cost commercial method for converting high-sulfur coal into environmentally acceptable fuel.

  2. ED breast cases and other breast emergencies.

    PubMed

    Khadem, Nasim; Reddy, Sravanthi; Lee, Sandy; Larsen, Linda; Walker, Daphne

    2016-02-01

    Patients with pathologic processes of the breast commonly present in the Emergency Department (ED). Familiarity with the imaging and management of the most common entities is essential for the radiologist. Additionally, it is important to understand the limitations of ED imaging and management in the acute setting and to recognize when referrals to a specialty breast center are necessary. The goal of this article is to review the clinical presentations, pathophysiology, imaging, and management of emergency breast cases and common breast pathology seen in the ED.

  3. Solventless pharmaceutical coating processes: a review.

    PubMed

    Bose, Sagarika; Bogner, Robin H

    2007-01-01

    Coatings are an essential part in the formulation of pharmaceutical dosage form to achieve superior aesthetic quality (e.g., color, texture, mouth feel, and taste masking), physical and chemical protection for the drugs in the dosage forms, and modification of drug release characteristics. Most film coatings are applied as aqueous- or organic-based polymer solutions. Both organic and aqueous film coating bring their own disadvantages. Solventless coating technologies can overcome many of the disadvantages associated with the use of solvents (e.g., solvent exposure, solvent disposal, and residual solvent in product) in pharmaceutical coating. Solventless processing reduces the overall cost by eliminating the tedious and expensive processes of solvent disposal/treatment. In addition, it can significantly reduce the processing time because there is no drying/evaporation step. These environment-friendly processes are performed without any heat in most cases (except hot-melt coating) and thus can provide an alternative technology to coat temperature-sensitive drugs. This review discusses and compares six solventless coating methods - compression coating, hot-melt coating, supercritical fluid spray coating, electrostatic coating, dry powder coating, and photocurable coating - that can be used to coat the pharmaceutical dosage forms.

  4. Teaching Elementary School Social Studies Methods under edTPA

    ERIC Educational Resources Information Center

    An, Sohyun

    2016-01-01

    This article reports a self-study that analyzes my experience as a teacher educator navigating a turbulent educational landscape with the advent of edTPA. The data consist of my journal entries, the syllabi, handouts, work submitted by my students, and course evaluations. Data were analyzed by using an inductive process to describe how the edTPA…

  5. The University Supervisor, edTPA, and the New Making of the Teacher

    ERIC Educational Resources Information Center

    Donovan, Martha K.; Cannon, Susan O.

    2018-01-01

    As university supervisors at a large, urban university in the southern US, we examined the ways that the Education Teacher Performance Assessment (edTPA) shaped the pedagogic relationships and decision-making processes of our students and ourselves during the spring of 2016. We situated this study of edTPA within the framework of critical policy…

  6. G. ED. Paper-Book 1974-1984. The Process of Growth of an Innovation.

    ERIC Educational Resources Information Center

    Verduin-Muller, Henriette, Ed.

    Fifteen papers presented at conferences throughout Europe and in the USSR, Nigeria, Japan, Jamaica, and Tunesia provide an introduction to the research work being done by the graduate level Department of Geography for Education (G.ED.) at the University of Utrecht in the Netherlands. An introductory chapter describes the three G.ED. modules, which…

  7. Next Generation Solvent (NGS): Development for Caustic-Side Solvent Extraction of Cesium

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Moyer, Bruce A.; Birdwell, Jr, Joseph F.; Bonnesen, Peter V.

    This report summarizes the FY 2010 and 2011 accomplishments at Oak Ridge National Laboratory (ORNL) in developing the Next Generation Caustic-Side Solvent Extraction (NG-CSSX) process, referred to commonly as the Next Generation Solvent (NGS), under funding from the U.S. Department of Energy, Office of Environmental Management (DOE-EM), Office of Technology Innovation and Development. The primary product of this effort is a process solvent and preliminary flowsheet capable of meeting a target decontamination factor (DF) of 40,000 for worst-case Savannah River Site (SRS) waste with a concentration factor of 15 or higher in the 18-stage equipment configuration of the SRS Modularmore » Caustic-Side Solvent Extraction Unit (MCU). In addition, the NG-CSSX process may be readily adapted for use in the SRS Salt Waste Processing Facility (SWPF) or in supplemental tank-waste treatment at Hanford upon appropriate solvent or flowsheet modifications. Efforts in FY 2010 focused on developing a solvent composition and process flowsheet for MCU implementation. In FY 2011 accomplishments at ORNL involved a wide array of chemical-development activities and testing up through single-stage hydraulic and mass-transfer tests in 5-cm centrifugal contactors. Under subcontract from ORNL, Argonne National Laboratory (ANL) designed a preliminary flowsheet using ORNL cesium distribution data, and Tennessee Technological University confirmed a chemical model for cesium distribution ratios (DCs) as a function of feed composition. Interlaboratory efforts were coordinated with complementary engineering tests carried out (and reported separately) by personnel at Savannah River National Laboratory (SRNL) and Savannah River Remediation (SRR) with helpful advice by Parsons Engineering and General Atomics on aspects of possible SWPF implementation.« less

  8. Next Generation Solvent Development for Caustic-Side Solvent Extraction of Cesium

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Moyer, Bruce A.; Birdwell, Joseph F.; Bonnesen, Peter V.

    This report summarizes the FY 2010 and 2011 accomplishments at Oak Ridge National Laboratory (ORNL) in developing the Next Generation Caustic-Side Solvent Extraction (NG-CSSX) process, referred to commonly as the Next Generation Solvent (NGS), under funding from the U.S. Department of Energy, Office of Environmental Management (DOE-EM), Office of Technology Innovation and Development. The primary product of this effort is a process solvent and preliminary flowsheet capable of meeting a target decontamination factor (DF) of 40,000 for worst-case Savannah River Site (SRS) waste with a concentration factor of 15 or higher in the 18-stage equipment configuration of the SRS Modularmore » Caustic-Side Solvent Extraction Unit (MCU). In addition, the NG-CSSX process may be readily adapted for use in the SRS Salt Waste Processing Facility (SWPF) or in supplemental tank-waste treatment at Hanford upon appropriate solvent or flowsheet modifications. Efforts in FY 2010 focused on developing a solvent composition and process flowsheet for MCU implementation. In FY 2011 accomplishments at ORNL involved a wide array of chemical-development activities and testing up through single-stage hydraulic and mass-transfer tests in 5-cm centrifugal contactors. Under subcontract from ORNL, Argonne National Laboratory (ANL) designed a preliminary flowsheet using ORNL cesium distribution data, and Tennessee Technological University confirmed a chemical model for cesium distribution ratios (DCs) as a function of feed composition. Inter laboratory efforts were coordinated with complementary engineering tests carried out (and reported separately) by personnel at Savannah River National Laboratory (SRNL) and Savannah River Remediation (SRR) with helpful advice by Parsons Engineering and General Atomics on aspects of possible SWPF implementation.« less

  9. Non-aqueous cleaning solvent substitution

    NASA Technical Reports Server (NTRS)

    Meier, Gerald J.

    1994-01-01

    A variety of environmental, safety, and health concerns exist over use of chlorinated and fluorinated cleaning solvents. Sandia National Laboratories, Lawrence Livermore National Laboratories, and the Kansas City Division of AlliedSignal have combined efforts to focus on finding alternative cleaning solvents and processes which are effective, environmentally safe, and compliant with local, state, and federal regulations. An alternative solvent has been identified, qualified, and implemented into production of complex electronic assemblies, where aqueous and semi-aqueous cleaning processes are not allowed. Extensive compatibility studies were performed with components, piece-parts, and materials. Electrical testing and accelerated aging were used to screen for detrimental, long-term effects. A terpene, d-limonene, was selected as the solvent of choice, and it was found to be compatible with the components and materials tested. A brief history of the overall project will be presented, along with representative cleaning efficiency results, compatibility results, and residual solvent data. The electronics industry is constantly searching for proven methods and environmentally-safe materials to use in manufacturing processes. The information in this presentation will provide another option to consider on future projects for applications requiring high levels of quality, reliability, and cleanliness from non-aqueous cleaning processes.

  10. Removal of ion-implanted photoresists on GaAs using two organic solvents in sequence

    NASA Astrophysics Data System (ADS)

    Oh, Eunseok; Na, Jihoon; Lee, Seunghyo; Lim, Sangwoo

    2016-07-01

    Organic solvents can effectively remove photoresists on III-V channels without damage or etching of the channel material during the process. In this study, a two-step sequential photoresist removal process using two different organic solvents was developed to remove implanted ArF and KrF photoresists at room temperature. The effects of organic solvents with either low molar volumes or high affinities for photoresists were evaluated to find a proper combination that can effectively remove high-dose implanted photoresists without damaging GaAs surfaces. The performance of formamide, acetonitrile, nitromethane, and monoethanolamine for the removal of ion-implanted ArF and KrF photoresists were compared using a two-step sequential photoresist removal process followed by treatment in dimethyl sulfoxide (DMSO). Among the various combinations, the acetonitrile + DMSO two-step sequence exhibited the best removal of photoresists that underwent ion implantation at doses of 5 × 1013-5 × 1015 atoms/cm2 on both flat and trench-structured GaAs surfaces. The ability of the two-step process using organic solvents to remove the photoresists can be explained by considering the affinities of solvents for a polymer and its permeability through the photoresist.

  11. Neuropsychological Component of Imagery Processing

    DTIC Science & Technology

    1991-01-25

    and von Bonin, G. (1951). The Isocortex of Man. Urbana, IL: University of Illinois Press. Bauer, R. M., and Rubens, A. B. (1985). Agnosia . In K. M...Apperceptive agnosia : the specification and description of constructs. In Humphreys, G. W., and Riddoch, M. J. (1987a) (Eds.). Visual Object Processing: A...visual processing: agnosias , achromatopsia, Balint’s syndrome and related difficulties of orientation and construction. In M.-M. Mesulam (Ed

  12. Hippi Care Hospital: Towards Proactive Business Processes in Emergency Room Services. Teaching Case

    ERIC Educational Resources Information Center

    Tan, Kar Way; Shankararaman, Venky

    2014-01-01

    It was 2:35 am on a Saturday morning. Wiki Lim, process specialist from the Process Innovation Centre (PIC) of Hippi Care Hospital (HCH), desperately doodling on her notepad for ideas to improve service delivery at HCH's Emergency Department (ED). HCH has committed to the public that its ED would meet the service quality criterion of serving 90%…

  13. Self-assembly and enhanced photocatalytic properties of BiOI hollow microspheres via a reactable ionic liquid.

    PubMed

    Xia, Jiexiang; Yin, Sheng; Li, Huaming; Xu, Hui; Yan, Yongsheng; Zhang, Qi

    2011-02-01

    BiOI uniform flowerlike hollow microspheres with a hole in its surface structures have been successfully synthesized through an EG-assisted solvothermal process in the presence of ionic liquid 1-butyl-3-methylimidazolium iodine ([Bmim]I). The as-prepared samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDS), nitrogen sorption, and diffuse reflectance spectroscopy (DRS). A possible formation mechanism for the growth of hollow microspheres was discussed. During the reactive process, ionic liquid not only acted as solvents and templates but also as an I source for the fabrication of BiOI hollow microspheres and was vital for the structure of hollow microspheres. Additionally, we evaluated the photocatalytic activities of BiOI on the degradation of methyl orange (MO) under visible light irradiation and found that as-prepared BiOI hollow microspheres exhibited higher photocatalytic activity than BiOI nanoplates and TiO(2) (Degussa, P25) did. On the basis of such analysis, it can be assumed that the enhanced photocatalytic activities of BiOI hollow microspheres could be ascribed to its energy band structure, high BET surface area, high surface-to-volume ratios, and light absorbance.

  14. Bio-Derived, Binderless, Hierarchically Porous Carbon Anodes for Li-ion Batteries

    PubMed Central

    Campbell, Brennan; Ionescu, Robert; Favors, Zachary; Ozkan, Cengiz S.; Ozkan, Mihrimah

    2015-01-01

    Here we explore the electrochemical performance of pyrolyzed skins from the species A. bisporus, also known as the Portobello mushroom, as free-standing, binder-free, and current collector-free Li-ion battery anodes. At temperatures above 900 °C, the biomass-derived carbon nanoribbon-like architectures undergo unique processes to become hierarchically porous. During heat-treatment, the oxygen and heteroatom-rich organics and potassium compounds naturally present in the mushroom skins play a mutual role in creating inner void spaces throughout the resulting carbon nanoribbons, which is a process analogous to KOH-activation of carbon materials seen in literature. The pores formed in the pyrolytic carbon nanoribbons range in size from sub-nanometer to tens of nanometers, making the nanoribbons micro, meso, and macroporous. Detailed studies were conducted on the carbon nanoribbons using SEM and TEM to study morphology, as well as XRD and EDS to study composition. The self-supporting nanoribbon anodes demonstrate significant capacity increase as they undergo additional charge/discharge cycles. After a pyrolysis temperature of 1100 °C, the pristine anodes achieve over 260 mAh/g after 700 cycles and a Coulombic efficiency of 101.1%, without the use of harmful solvents or chemical activation agents. PMID:26415917

  15. Process for enhancing the value of hydrocabonaceous natural recources

    DOEpatents

    Bunger, James W.; Cogswell, Donald E.

    2005-04-05

    A process for upgrading hydrocarbonaceous oil containing heteroatom-containing compounds where the hydrocarbonaceous oil is contacted with a solvent system that is a mixture of a major portion of a polar solvent having a dipole moment greater than about 1 debye and a minor portion of water to selectively separate the constituents of the carbonaceous oil into a heteroatom-depleted raffinate fraction and heteroatom-enriched extract fraction. The polar solvent and the water-in-solvent system are formulated at a ratio where the water is an antisolvent in an amount to inhibit solubility of heteroatom-containing compounds and the polar solvent in the raffinate, and to inhibit solubility of non-heteroatom-containing compounds in the extract. The ratio of the hydrocarbonaceous oil to the solvent system is such that a coefficient of separation is at least 50%. The coefficient of separation is the mole percent of heteroatom-containing compounds from the carbonaceous oil that are recovered in the extract fraction minus the mole percent of non-heteroatom-containing compounds from the carbonaceous oil that are recovered in the extract fraction. The solvent-free extract and the raffinate concentrates may be used directly or processed to make valuable petroleum, chemical or industrial products.

  16. Radiolytic Treatment of the Next-Generation Caustic-Side Solvent Extraction (NGS) Solvent and its Effect on the NGS Process

    DOE PAGES

    Roach, Benjamin D.; Williams, Neil J.; Duncan, Nathan C.; ...

    2014-12-01

    We show in this work that the solvent used in the Next Generation Caustic-Side Solvent Extraction (NGS) process can withstand a radiation dose well in excess of the dose it would receive in multiple years of treating legacy salt waste at the US Department of Energy Savannah River Site. The solvent was subjected to a maximum of 50 kGy of gamma radiation while in dynamic contact with each of the aqueous phases of the current NGS process, namely SRS-15 (a highly caustic waste simulant), sodium hydroxide scrub solution (0.025 M), and boric acid strip solution (0.01 M). Bench-top testing ofmore » irradiated solvent confirmed that irradiation has inconsequential impact on the extraction, scrubbing, and stripping performance of the solvent up to 13 times the estimated 0.73 kGy/y annual absorbed dose. Lastly, stripping performance is the most sensitive step to radiation, deteriorating more due to buildup of p-sec-butylphenol (SBP) and possibly other proton-ionizable products than to degradation of the guanidine suppressor, as shown by chemical analyses.« less

  17. Radiolytic Treatment of the Next-Generation Caustic-Side Solvent Extraction (NGS) Solvent and its Effect on the NGS Process

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Roach, Benjamin D.; Williams, Neil J.; Duncan, Nathan C.

    We show in this work that the solvent used in the Next Generation Caustic-Side Solvent Extraction (NGS) process can withstand a radiation dose well in excess of the dose it would receive in multiple years of treating legacy salt waste at the US Department of Energy Savannah River Site. The solvent was subjected to a maximum of 50 kGy of gamma radiation while in dynamic contact with each of the aqueous phases of the current NGS process, namely SRS-15 (a highly caustic waste simulant), sodium hydroxide scrub solution (0.025 M), and boric acid strip solution (0.01 M). Bench-top testing ofmore » irradiated solvent confirmed that irradiation has inconsequential impact on the extraction, scrubbing, and stripping performance of the solvent up to 13 times the estimated 0.73 kGy/y annual absorbed dose. Lastly, stripping performance is the most sensitive step to radiation, deteriorating more due to buildup of p-sec-butylphenol (SBP) and possibly other proton-ionizable products than to degradation of the guanidine suppressor, as shown by chemical analyses.« less

  18. Solvent recovery opportunities in the pharmaceutical industry.

    PubMed

    Barton, P I

    2000-11-01

    Opportunities for recovering and recycling waste solvent streams in the pharmaceutical industry are reviewed. A major obstacle to solvent recovery and recycling is the existence of azeotropic compositions, and thus separation barriers, in the mixtures in question. Advances in the understanding of these complex separation problems are discussed. Recent progress on novel designs for small-scale, flexible azeotropic separation processes is reviewed. Also considered is the alternative and complementary approach of integrating solvent use within a batch process so that the formation of hard-to-separate azeotropic compositions is prevented.

  19. Technical and economic analysis of solvent-based lithium-ion electrode drying with water and NMP

    DOE PAGES

    Wood, David L.; Quass, Jeffrey D.; Li, Jianlin; ...

    2017-05-16

    Processing lithium-ion battery (LIB) electrode dispersions with water as the solvent during primary drying offers many advantages over N-methylpyrrolidone (NMP). An in-depth analysis of the comparative drying costs of LIB electrodes is discussed for both NMP- and water-based dispersion processing in terms of battery pack $/kWh. Electrode coating manufacturing and capital equipment cost savings are compared for water vs. conventional NMP organic solvent processing. A major finding of this work is that the total electrode manufacturing costs, whether water- or NMP-based, contribute about 8–9% of the total pack cost. However, it was found that up to a 2 × reductionmore » in electrode processing (drying and solvent recovery) cost can be expected along with a $3–6 M savings in associated plant capital equipment (for a plant producing 100,000 10-kWh Plug-in Hybrid Electric Vehicle (PHEV) batteries) using water as the electrode solvent. This paper shows a different perspective in that the most important benefits of aqueous electrode processing actually revolve around capital equipment savings and environmental stewardship and not processing cost savings.« less

  20. Nanofiltration-Enabled In Situ Solvent and Reagent Recycle for Sustainable Continuous-Flow Synthesis.

    PubMed

    Fodi, Tamas; Didaskalou, Christos; Kupai, Jozsef; Balogh, Gyorgy T; Huszthy, Peter; Szekely, Gyorgy

    2017-09-11

    Solvent usage in the pharmaceutical sector accounts for as much as 90 % of the overall mass during manufacturing processes. Consequently, solvent consumption poses significant costs and environmental burdens. Continuous processing, in particular continuous-flow reactors, have great potential for the sustainable production of pharmaceuticals but subsequent downstream processing remains challenging. Separation processes for concentrating and purifying chemicals can account for as much as 80 % of the total manufacturing costs. In this work, a nanofiltration unit was coupled to a continuous-flow rector for in situ solvent and reagent recycling. The nanofiltration unit is straightforward to implement and simple to control during continuous operation. The hybrid process operated continuously over six weeks, recycling about 90 % of the solvent and reagent. Consequently, the E-factor and the carbon footprint were reduced by 91 % and 19 %, respectively. Moreover, the nanofiltration unit led to a solution of the product eleven times more concentrated than the reaction mixture and increased the purity from 52.4 % to 91.5 %. The boundaries for process conditions were investigated to facilitate implementation of the methodology by the pharmaceutical sector. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  1. Enhanced low-temperature NH3-SCR performance of MnOx/CeO2 catalysts by optimal solvent effect

    NASA Astrophysics Data System (ADS)

    Yao, Xiaojiang; Kong, Tingting; Chen, Li; Ding, Shimin; Yang, Fumo; Dong, Lin

    2017-10-01

    A series of MnOx/CeO2 catalysts were prepared by modulating the solvents (deionized water (DW), anhydrous ethanol (AE), acetic acid (AA), and oxalic acid (OA) solution) with the purpose of improving the low-temperature NH3-SCR performance, broadening the operating temperature window, and enhancing the H2O + SO2 resistance. The synthesized catalysts were characterized by means of N2-physisorption, XRD, EDS mapping, Raman, XPS, H2-TPR, NH3-TPD, and in situ DRIFTS technologies. Furthermore, the catalytic performance and H2O + SO2 resistance were evaluated by NH3-SCR model reaction. The obtained results indicate that MnOx/CeO2 catalyst prepared with oxalic acid solution as a solvent exhibits the best catalytic performance among these catalysts, which shows above 80% NO conversion during a wide operating temperature range of 100-250 °C and good H2O + SO2 resistance for low-temperature NH3-SCR reaction. This is related to that oxalic acid solution can promote the dispersion of MnOx and enhance the electron interaction between MnOx and CeO2, which are beneficial to improving the physicochemical property of MnOx/CeO2 catalyst, and further lead to the enhancement of catalytic performance and good H2O + SO2 resistance.

  2. Investigations of the Interactions of Radiation with Matter.

    DTIC Science & Technology

    1986-07-31

    Process in Atoms, Molecules and Solids, eds. A. Mei-el and J. Finster , (Karl-Marx Universitat, Leipzig, 1984), p. 58. 10. S.T. Manson in High Enery Ion...H. Toburen, and S. T. Manson in X-Ra and Inner-Shell Process in Atoms, Molecules and Solids, eds. A. Meisel and J. Finster , (Karl-Marx- Universitat

  3. Emotional Processing, Recognition, Empathy and Evoked Facial Expression in Eating Disorders: An Experimental Study to Map Deficits in Social Cognition

    PubMed Central

    Cardi, Valentina; Corfield, Freya; Leppanen, Jenni; Rhind, Charlotte; Deriziotis, Stephanie; Hadjimichalis, Alexandra; Hibbs, Rebecca; Micali, Nadia; Treasure, Janet

    2015-01-01

    Background Difficulties in social cognition have been identified in eating disorders (EDs), but the exact profile of these abnormalities is unclear. The aim of this study is to examine distinct processes of social-cognition in this patient group, including attentional processing and recognition, empathic reaction and evoked facial expression in response to discrete vignettes of others displaying positive (i.e. happiness) or negative (i.e. sadness and anger) emotions. Method One hundred and thirty-eight female participants were included in the study: 73 healthy controls (HCs) and 65 individuals with an ED (49 with Anorexia Nervosa and 16 with Bulimia Nervosa). Self-report and behavioural measures were used. Results Participants with EDs did not display specific abnormalities in emotional processing, recognition and empathic response to others’ basic discrete emotions. However, they had poorer facial expressivity and a tendency to turn away from emotional displays. Conclusion Treatments focusing on the development of non-verbal emotional communication skills might be of benefit for patients with EDs. PMID:26252220

  4. An Integrated, Low Temperature Process to Capture and Sequester Carbon Dioxide from Industrial Emissions

    NASA Astrophysics Data System (ADS)

    Wendlandt, R. F.; Foremski, J. J.

    2013-12-01

    Laboratory experiments show that it is possible to integrate (1) the chemistry of serpentine dissolution, (2) capture of CO2 gas from the combustion of natural gas and coal-fired power plants using aqueous amine-based solvents, (3) long-term CO2 sequestration via solid phase carbonate precipitation, and (4) capture solvent regeneration with acid recycling in a single, continuous process. In our process, magnesium is released from serpentine at 300°C via heat treatment with ammonium sulfate salts or at temperatures as low as 50°C via reaction with sulfuric acid. We have also demonstrated that various solid carbonate phases can be precipitated directly from aqueous amine-based (NH3, MEA, DMEA) CO2 capture solvent solutions at room temperature. Direct precipitation from the capture solvent enables regenerating CO2 capture solvent without the need for heat and without the need to compress the CO2 off gas. We propose that known low-temperature electrochemical methods can be integrated with this process to regenerate the aqueous amine capture solvent and recycle acid for dissolution of magnesium-bearing mineral feedstocks and magnesium release. Although the direct precipitation of magnesite at ambient conditions remains elusive, experimental results demonstrate that at temperatures ranging from 20°C to 60°C, either nesquehonite Mg(HCO3)(OH)●2H2O or a double salt with the formula [NH4]2Mg(CO3)2●4H2O or an amorphous magnesium carbonate precipitate directly from the capture solvent. These phases are less desirable for CO2 sequestration than magnesite because they potentially remove constituents (water, ammonia) from the reaction system, reducing the overall efficiency of the sequestration process. Accordingly, the integrated process can be accomplished with minimal energy consumption and loss of CO2 capture and acid solvents, and a net generation of 1 to 4 moles of H2O/6 moles of CO2 sequestered (depending on the solid carbonate precipitate and amount of produced H2 and O2 gas reacted to produce heat and water). Features of the integrated process include the following: 1) the four separate processes have compatible chemistry, enabling design of an integrated, continuous process scheme for CO2 capture and sequestration; 2) all 4 stages of the process can be conducted at ambient or slightly elevated temperatures; 3) precipitating carbonate directly from the capture solvent eliminates the need for costly CO2 gas compression; and 4) recycling the acid used for serpentine dissolution and the solvent used for CO2 capture reduces feed stock costs.

  5. Enhancements in mass transfer for carbon capture solvents part I: Homogeneous catalyst

    DOE PAGES

    Widger, Leland R.; Sarma, Moushumi; Bryant, Jonathan J.; ...

    2017-06-15

    The novel small molecule carbonic anhydrase (CA) mimic [Co III(Salphen-COO -)Cl]HNEt 3 ( 1), was synthesized as an additive for increasing CO 2 absorption rates in amine-based post-combustion carbon capture processes (CCS), and its efficacy was verified. 1 was designed for use in a kinetically slow but thermally stable blended solvent, containing the primary amines 1-amino-2-propanol (A2P) and 2-amino-2-methyl-1-propanol (AMP). Together, the A2P/AMP solvent and 1 reduce the overall energy penalty associated with CO 2 capture from coal-derived flue gas, relative to the baseline solvent MEA. 1 is also effective at increasing absorption kinetics of kinetically fast solvents, such asmore » MEA, which can reduce capital costs by requiring a smaller absorber tower. The transition from catalyst testing under idealized laboratory conditions, to process relevant lab- and bench-scale testing adds many additional variables that are not well understood and rarely discussed. As a result, the stepwise testing of both 1 and the novel A2P/AMP solvent blend is described through a transition process that identifies many of these process and evaluation challenges not often addressed when designing a chemical or catalytic additive for industrial CCS systems, where consideration of solvent chemistry is typically the primary goal.« less

  6. Enhancements in mass transfer for carbon capture solvents part II: Micron-sized solid particles

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Mannel, David S.; Qi, Guojie; Widger, Leland R.

    2017-06-01

    The novel small molecule carbonic anhydrase (CA) mimic [CoIII(Salphen-COO-)Cl]HNEt3 (1), was synthesized as an additive for increasing CO2 absorption rates in amine-based post-combustion carbon capture processes (CCS), and its efficacy was verified. 1 was designed for use in a kinetically slow but thermally stable blended solvent, containing the primary amines 1-amino-2-propanol (A2P) and 2-amino-2-methyl-1-propanol (AMP). Together, the A2P/AMP solvent and 1 reduce the overall energy penalty associated with CO2 capture from coal-derived flue gas, relative to the baseline solvent MEA. 1 is also effective at increasing absorption kinetics of kinetically fast solvents, such as MEA, which can reduce capital costsmore » by requiring a smaller absorber tower. The transition from catalyst testing under idealized laboratory conditions, to process relevant lab- and bench-scale testing adds many additional variables that are not well understood and rarely discussed. The stepwise testing of both 1 and the novel A2P/AMP solvent blend is described through a transition process that identifies many of these process and evaluation challenges not often addressed when designing a chemical or catalytic additive for industrial CCS systems, where consideration of solvent chemistry is typically the primary goal.« less

  7. Enzymes from solvent-tolerant microbes: useful biocatalysts for non-aqueous enzymology.

    PubMed

    Gupta, Anshu; Khare, S K

    2009-01-01

    Solvent-tolerant microbes are a newly emerging class that possesses the unique ability to thrive in the presence of organic solvents. Their enzymes adapted to mediate cellular and metabolic processes in a solvent-rich environment and are logically stable in the presence of organic solvents. Enzyme catalysis in non-aqueous/low-water media is finding increasing applications for the synthesis of industrially important products, namely peptides, esters, and other trans-esterification products. Solvent stability, however, remains a prerequisite for employing enzymes in non-aqueous systems. Enzymes, in general, get inactivated or give very low rates of reaction in non-aqueous media. Thus, early efforts, and even some recent ones, have aimed at stabilization of enzymes in organic media by immobilization, surface modifications, mutagenesis, and protein engineering. Enzymes from solvent-tolerant microbes appear to be the choicest source for studying solvent-stable enzymes because of their unique ability to survive in the presence of a range of organic solvents. These bacteria circumvent the solvent's toxic effects by virtue of various adaptations, e.g. at the level of the cytoplasmic membrane, by degradation and transformation of solvents, and by active excretion of solvents. The recent screening of these exotic microbes has generated some naturally solvent-stable proteases, lipases, cholesterol oxidase, cholesterol esterase, cyclodextrin glucanotransferase, and other important enzymes. The unique properties of these novel biocatalysts have great potential for applications in non-aqueous enzymology for a range of industrial processes.

  8. Lean techniques for the improvement of patients’ flow in emergency department

    PubMed Central

    Chan, HY; Lo, SM; Lee, LLY; Lo, WYL; Yu, WC; Wu, YF; Ho, ST; Yeung, RSD; Chan, JTS

    2014-01-01

    BACKGROUND: Emergency departments (EDs) face problems with overcrowding, access block, cost containment, and increasing demand from patients. In order to resolve these problems, there is rising interest to an approach called “lean” management. This study aims to (1) evaluate the current patient flow in ED, (2) to identify and eliminate the non-valued added process, and (3) to modify the existing process. METHODS: It was a quantitative, pre- and post-lean design study with a series of lean management work implemented to improve the admission and blood result waiting time. These included structured re-design process, priority admission triage (PAT) program, enhanced communication with medical department, and use of new high sensitivity troponin-T (hsTnT) blood test. Triage waiting time, consultation waiting time, blood result time, admission waiting time, total processing time and ED length of stay were compared. RESULTS: Among all the processes carried out in ED, the most time consuming processes were to wait for an admission bed (38.24 minutes; SD 66.35) and blood testing result (mean 52.73 minutes, SD 24.03). The triage waiting time and end waiting time for consultation were significantly decreased. The admission waiting time of emergency medical ward (EMW) was significantly decreased from 54.76 minutes to 24.45 minutes after implementation of PAT program (P<0.05). CONCLUSION: The application of lean management can improve the patient flow in ED. Acquiescence to the principle of lean is crucial to enhance high quality emergency care and patient satisfaction. PMID:25215143

  9. Organic solvent pretreatment of lignocellulosic biomass for biofuels and biochemicals: A review.

    PubMed

    Zhang, Ke; Pei, Zhijian; Wang, Donghai

    2016-01-01

    Lignocellulosic biomass represents the largest potential volume and lowest cost for biofuel and biochemical production. Pretreatment is an essential component of biomass conversion process, affecting a majority of downstream processes, including enzymatic hydrolysis, fermentation, and final product separation. Organic solvent pretreatment is recognized as an emerging way ahead because of its inherent advantages, such as the ability to fractionate lignocellulosic biomass into cellulose, lignin, and hemicellulose components with high purity, as well as easy solvent recovery and solvent reuse. Objectives of this review were to update and extend previous works on pretreatment of lignocellulosic biomass for biofuels and biochemicals using organic solvents, especially on ethanol, methanol, ethylene glycol, glycerol, acetic acid, and formic acid. Perspectives and recommendations were given to fully describe implementation of proper organic solvent pretreatment for future research. Copyright © 2015 Elsevier Ltd. All rights reserved.

  10. Fabrication of Janus particles composed of poly (lactic-co-glycolic) acid and hard fat using a solvent evaporation method.

    PubMed

    Matsumoto, Akihiro; Murao, Satoshi; Matsumoto, Michiko; Watanabe, Chie; Murakami, Masahiro

    The feasibility of fabricating Janus particles based on phase separation between a hard fat and a biocompatible polymer was investigated. The solvent evaporation method used involved preparing an oil-in-water (o/w) emulsion with a mixture of poly (lactic-co-glycolic) acid (PLGA), hard fat, and an organic solvent as the oil phase and a polyvinyl alcohol aqueous solution as the water phase. The Janus particles were formed when the solvent was evaporated to obtain certain concentrations of PLGA and hard fat in the oil phase, at which phase separation was estimated to occur based on the phase diagram analysis. The hard fat hemisphere was proven to be the oil phase using a lipophilic dye Oil Red O. When the solvent evaporation process was performed maintaining a specific volume during the emulsification process; Janus particles were formed within 1.5 h. However, the formed Janus particles were destroyed by stirring for over 6 h. In contrast, a few Janus particles were formed when enough water to dissolve the oil phase solvent was added to the emulsion immediately after the emulsification process. The optimized volume of the solvent evaporation medium dominantly formed Janus particles and maintained the conformation for over 6 h with stirring. These results indicate that the formation and stability of Janus particles depend on the rate of solvent evaporation. Therefore, optimization of the solvent evaporation rate is critical to obtaining stable PLGA and hard fat Janus particles.

  11. Does excessive daytime sleepiness affect children's pedestrian safety?

    PubMed

    Avis, Kristin T; Gamble, Karen L; Schwebel, David C

    2014-02-01

    Many cognitive factors contribute to unintentional pedestrian injury, including reaction time, impulsivity, risk-taking, attention, and decision-making. These same factors are negatively influenced by excessive daytime sleepiness (EDS), which may place children with EDS at greater risk for pedestrian injury. Using a case-control design, 33 children age 8 to 16 y with EDS from an established diagnosis of narcolepsy or idiopathic hypersomnia (IHS) engaged in a virtual reality pedestrian environment while unmedicated. Thirty-three healthy children matched by age, race, sex, and household income served as controls. Children with EDS were riskier pedestrians than healthy children. They were twice as likely to be struck by a virtual vehicle in the virtual pedestrian environment than healthy controls. Attentional skills of looking at oncoming traffic were not impaired among children with EDS, but decision-making for when to cross the street safely was significantly impaired. Results suggest excessive daytime sleepiness (EDS) from the clinical sleep disorders known as the hypersomnias of central origin may have significant consequences on children's daytime functioning in a critical domain of personal safety, pedestrian skills. Cognitive processes involved in safe pedestrian crossings may be impaired in children with EDS. In the pedestrian simulation, children with EDS appeared to show a pattern consistent with inattentional blindness, in that they "looked but did not process" information in their pedestrian environment. Results highlight the need for heightened awareness of potentially irreversible consequences of untreated sleep disorders and identify a possible target for pediatric injury prevention.

  12. Balanced nuclear and cytoplasmic activities of EDS1 are required for a complete plant innate immune response.

    PubMed

    García, Ana V; Blanvillain-Baufumé, Servane; Huibers, Robin P; Wiermer, Marcel; Li, Guangyong; Gobbato, Enrico; Rietz, Steffen; Parker, Jane E

    2010-07-01

    An important layer of plant innate immunity to host-adapted pathogens is conferred by intracellular nucleotide-binding/oligomerization domain-leucine rich repeat (NB-LRR) receptors recognizing specific microbial effectors. Signaling from activated receptors of the TIR (Toll/Interleukin-1 Receptor)-NB-LRR class converges on the nucleo-cytoplasmic immune regulator EDS1 (Enhanced Disease Susceptibility1). In this report we show that a receptor-stimulated increase in accumulation of nuclear EDS1 precedes or coincides with the EDS1-dependent induction and repression of defense-related genes. EDS1 is capable of nuclear transport receptor-mediated shuttling between the cytoplasm and nucleus. By enhancing EDS1 export from inside nuclei (through attachment of an additional nuclear export sequence (NES)) or conditionally releasing EDS1 to the nucleus (by fusion to a glucocorticoid receptor (GR)) in transgenic Arabidopsis we establish that the EDS1 nuclear pool is essential for resistance to biotrophic and hemi-biotrophic pathogens and for transcriptional reprogramming. Evidence points to post-transcriptional processes regulating receptor-triggered accumulation of EDS1 in nuclei. Changes in nuclear EDS1 levels become equilibrated with the cytoplasmic EDS1 pool and cytoplasmic EDS1 is needed for complete resistance and restriction of host cell death at infection sites. We propose that coordinated nuclear and cytoplasmic activities of EDS1 enable the plant to mount an appropriately balanced immune response to pathogen attack.

  13. Coal liquefaction process using pretreatment with a binary solvent mixture

    DOEpatents

    Miller, R.N.

    1986-10-14

    An improved process for thermal solvent refining or hydroliquefaction of non-anthracitic coal at elevated temperatures under hydrogen pressure in a hydrogen donor solvent comprises pretreating the coal with a binary mixture of an aromatic hydrocarbon and an aliphatic alcohol at a temperature below 300 C before the hydroliquefaction step. This treatment generally increases both conversion of coal and yields of oil. 1 fig.

  14. Coal liquefaction process using pretreatment with a binary solvent mixture

    DOEpatents

    Miller, Robert N.

    1986-01-01

    An improved process for thermal solvent refining or hydroliquefaction of non-anthracitic coal at elevated temperatures under hydrogen pressure in a hydrogen donor solvent comprises pretreating the coal with a binary mixture of an aromatic hydrocarbon and an aliphatic alcohol at a temperature below 300.degree. C. before the hydroliquefaction step. This treatment generally increases both conversion of coal and yields of oil.

  15. Process quality indicators targeting cognitive impairment to support quality of care for older people with cognitive impairment in emergency departments.

    PubMed

    Schnitker, Linda M; Martin-Khan, Melinda; Burkett, Ellen; Beattie, Elizabeth R A; Jones, Richard N; Gray, Len C

    2015-03-01

    The objective of this study was to develop process quality indicators (PQIs) to support the improvement of care services for older people with cognitive impairment in emergency departments (ED). A structured research approach was taken for the development of PQIs for the care of older people with cognitive impairment in EDs, including combining available evidence with expert opinion (phase 1), a field study (phase 2), and formal voting (phase 3). A systematic review of the literature identified ED processes targeting the specific care needs of older people with cognitive impairment. Existing relevant PQIs were also included. By integrating the scientific evidence and clinical expertise, new PQIs were drafted and, along with the existing PQIs, extensively discussed by an advisory panel. These indicators were field tested in eight hospitals using a cohort of older persons aged 70 years and older. After analysis of the field study data (indicator prevalence, variability across sites), in a second meeting, the advisory panel further defined the PQIs. The advisory panel formally voted for selection of those PQIs that were most appropriate for care evaluation. In addition to seven previously published PQIs relevant to the care of older persons, 15 new indicators were created. These 22 PQIs were then field tested. PQIs designed specifically for the older ED population with cognitive impairment were only scored for patients with identified cognitive impairment. Following formal voting, a total of 11 PQIs were included in the set. These PQIs targeted cognitive screening, delirium screening, delirium risk assessment, evaluation of acute change in mental status, delirium etiology, proxy notification, collateral history, involvement of a nominated support person, pain assessment, postdischarge follow-up, and ED length of stay. This article presents a set of PQIs for the evaluation of the care for older people with cognitive impairment in EDs. The variation in indicator triggering across different ED sites suggests that there are opportunities for quality improvement in care for this vulnerable group. Applied PQIs will identify an emergency services' implementation of care strategies for cognitively impaired older ED patients. Awareness of the PQI triggers at an ED level enables implementation of targeted interventions to improve any suboptimal processes of care. Further validation and utility of the indicators in a wider population is now indicated. © 2015 by the Society for Academic Emergency Medicine.

  16. Natal teeth

    MedlinePlus

    ... process. In: Dean JA, ed. McDonald and Avery's Dentistry for the Child and Adolescent . 10th ed. St. ... Updated by: Michael Kapner, DDS, general and aesthetic dentistry, Norwalk Medical Center, Norwalk, CT. Review provided by ...

  17. The role of the 'lifestyle' label and negative bias in the allocation of health resources for erectile dysfunction drugs: an ethics-based appraisal.

    PubMed

    Manson, H

    2006-01-01

    There have been recent calls for the re-evaluation of health resource allocation for erectile dysfunction (ED) drugs. This paper discusses sociocultural prejudices associated with ED and its treatment, arising from the link with sexuality, the perception that ED is a 'lifestyle' issue and the belief that ED is part of the normal ageing process. These views diminish the perceived importance of sexual health, extending subjectively into the funding arena as a 'negative bias'. Empirical data are presented, which demonstrate that ED can have significant psychosocial consequences, and that ED drugs are valuable quality-of-life interventions. The assumption that ED is an inevitable part of ageing is also analysed and found to be questionable. Health resource allocation decisions for ED drugs must be conducted with an awareness of the ethical and clinical complexities described in this paper, and with the sensibility that negative personal value judgments (on the part of policymakers) must be guarded against.

  18. Implementing Data Definition Consistency for Emergency Department Operations Benchmarking and Research.

    PubMed

    Yiadom, Maame Yaa A B; Scheulen, James; McWade, Conor M; Augustine, James J

    2016-07-01

    The objective was to obtain a commitment to adopt a common set of definitions for emergency department (ED) demographic, clinical process, and performance metrics among the ED Benchmarking Alliance (EDBA), ED Operations Study Group (EDOSG), and Academy of Academic Administrators of Emergency Medicine (AAAEM) by 2017. A retrospective cross-sectional analysis of available data from three ED operations benchmarking organizations supported a negotiation to use a set of common metrics with identical definitions. During a 1.5-day meeting-structured according to social change theories of information exchange, self-interest, and interdependence-common definitions were identified and negotiated using the EDBA's published definitions as a start for discussion. Methods of process analysis theory were used in the 8 weeks following the meeting to achieve official consensus on definitions. These two lists were submitted to the organizations' leadership for implementation approval. A total of 374 unique measures were identified, of which 57 (15%) were shared by at least two organizations. Fourteen (4%) were common to all three organizations. In addition to agreement on definitions for the 14 measures used by all three organizations, agreement was reached on universal definitions for 17 of the 57 measures shared by at least two organizations. The negotiation outcome was a list of 31 measures with universal definitions to be adopted by each organization by 2017. The use of negotiation, social change, and process analysis theories achieved the adoption of universal definitions among the EDBA, EDOSG, and AAAEM. This will impact performance benchmarking for nearly half of US EDs. It initiates a formal commitment to utilize standardized metrics, and it transitions consistency in reporting ED operations metrics from consensus to implementation. This work advances our ability to more accurately characterize variation in ED care delivery models, resource utilization, and performance. In addition, it permits future aggregation of these three data sets, thus facilitating the creation of more robust ED operations research data sets unified by a universal language. Negotiation, social change, and process analysis principles can be used to advance the adoption of additional definitions. © 2016 by the Society for Academic Emergency Medicine.

  19. One-Pot Route towards Active TiO2 Doped Hierarchically Porous Cellulose: Highly Efficient Photocatalysts for Methylene Blue Degradation

    PubMed Central

    Sun, Xiaoxia; Wang, Kunpeng; Shu, Yu; Zou, Fangdong; Zhang, Boxing; Sun, Guangwu; Uyama, Hiroshi; Wang, Xinhou

    2017-01-01

    In this study, novel photocatalyst monolith materials were successfully fabricated by a non-solvent induced phase separation (NIPS) technique. By adding a certain amount of ethyl acetate (as non-solvent) into a cellulose/LiCl/N,N-dimethylacetamide (DMAc) solution, and successively adding titanium dioxide (TiO2) nanoparticles (NPs), cellulose/TiO2 composite monoliths with hierarchically porous structures were easily formed. The obtained composite monoliths possessed mesopores, and two kinds of macropores. Scanning Electron Microscope (SEM), Energy Dispersive Spectroscopy (EDS), Fourier Transform Infrared Spectroscopy (FT-IR), X-ray Diffraction (XRD), Brunauer-Emmett-Teller (BET), and Ultraviolet-visible Spectroscopy (UV-Vis) measurements were adopted to characterize the cellulose/TiO2 composite monolith. The cellulose/TiO2 composite monoliths showed high efficiency of photocatalytic activity in the decomposition of methylene blue dye, which was decomposed up to 99% within 60 min under UV light. Moreover, the composite monoliths could retain 90% of the photodegradation efficiency after 10 cycles. The novel NIPS technique has great potential for fabricating recyclable photocatalysts with highly efficiency. PMID:28772734

  20. Synthesis of Crooked Gold Nanocrystals by Electrochemical Technique

    NASA Astrophysics Data System (ADS)

    Huang, Chien-Jung; Chiu, Pin-Hsiang; Chen, Ming-Da; Meen, Teen-Hang

    2005-07-01

    In this article, we demonstrate the synthesis of crooked gold nanocrystals (CGNCs) by an electrochemical technique using micelle templates formed by two surfactants with different amounts of isopropanol solvent, the primary surfactant being hexadecyltrimethylammonium bromide (C16TABr) and the cosurfactant being tetradodecylammonium bromide (TC12ABr). To investigate the influence of isopropanol solvent on the CGNCs, the amount of isopropanol was varied in the range from 50 to 300 μL. It was found that the aspect ratios (γ) of CGNCs were in the range from 1.06 to 1.46, and the UV--vis optical absorption measurement revealed a pronounced redshift of the surface plasmon band from 532 to 560 nm. The CGNCs were composed of many large gold grains with small gold nuclei, and it was determined that several grains are present within each of the CGNCs using a dark-field transmission electron microscopy (TEM) image. It is suggested that the CGNCs have a polycrystalline structure. The CGNCs have been determined to be pure gold with a face-centered cubic (fcc) structure by electron diffraction (ED) analysis.

  1. An Analysis of EMS and ED Detection of Stroke.

    PubMed

    Medoro, Ian; Cone, David C

    2017-01-01

    Studies have shown a reduction in time-to-CT and improved process measures when EMS personnel notify the ED of a "stroke alert" from the field. However, there are few data on the accuracy of these EMS stroke alerts. The goal of this study was to examine diagnostic test performance of EMS and ED stroke alerts and related process measures. The EMS and ED records of all stroke alerts in a large tertiary ED from August 2013-January 2014 were examined and data abstracted by one trained investigator, with data accuracy confirmed by a second investigator for 15% of cases. Stroke alerts called by EMS prior to ED arrival were compared to stroke alerts called by ED physicians and nurses (for walk-in patients, and patients transported by EMS without EMS stroke alerts). Means ± SD, medians, unpaired t-tests (for continuous data), and two-tailed Fisher's exact tests (for categorical data) were used. Of 260 consecutive stroke alerts, 129 were EMS stroke alerts, and 131 were ED stroke alerts (70 called by physicians, 61 by nurses). The mean NIH Stroke Scale was higher in the EMS group (8.1 ± 7.6 vs. 3.0 ± 5.0, p < 0.0001). The positive predictive value of EMS stroke alerts was 0.60 (78/129), alerts by ED nurses was 0.25 (15/61), and alerts by ED physicians was 0.31 (22/70). The PPV for EMS was better than for nurses or physicians (both p < 0.001), and more patients in the EMS group had final diagnoses of stroke (62/129 vs. 24/131, p < 0.001). The positive likelihood ratio was 1.53 for EMS personnel, 0.45 for physicians, and 0.77 for nurses. The mean time to order the CT (8.5 ± 7.1 min vs. 23.1 ± 18.2 min, p < 0.0001) and the mean ED length of stay (248 ± 116 min vs. 283 ± 128 min, p = 0.022) were shorter for the EMS stroke alert group. More EMS stroke alert patients received tPA (16/129 vs. 6/131, p = 0.027). EMS stroke alerts have better diagnostic test performance than stroke alerts by ED staff, likely due to higher NIH Stroke Scale scores (more obvious presentations) and are associated with better process measures. The fairly low PPV suggests room for improvement in prehospital stroke protocols.

  2. Microporous plastic member such as a battery separator and process for making same

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Sundberg, E.G.; Campbell, G.A.; Doucette, E.I.

    A process for producing a microporous plastic member useful as a battery separator comprises the following operations: forming a coherent dough by mixing a vinyl chloride resin with a plasticizing amount of a first solvent and with finely divided particles of a filler which contains volatilizable releasable constituent by heating and which shrinks substantially and irreversibly upon release of the volatilizable constituent, an example of which is hydrated silica; forming the solvent-containing dough into a shaped member; extracting the first solvent from the member before any substantial evaporation of solvent occurs by contacting it with a second solvent in amore » liquid bath at a temperature substantially below the boiling point of any liquid present, the second solvent being one which is capable of dissolving the first solvent without dissolving the resin and the filler, thereby deplasticizing the member by extractively removing the first solvent from the member; and thereafter heating the member at an elevated temperature but below the softening point of the resin until the filler is shrunk within the member by release of its volatilizable content. 10 claims.« less

  3. NEPTUNIUM SOLVENT EXTRACTION PROCESS

    DOEpatents

    Dawson, L.R.; Fields, P.R.

    1959-10-01

    The separation of neptunium from an aqueous solution by solvent extraction and the extraction of neptunium from the solvent solution are described. Neptunium is separated from an aqueous solution containing tetravalent or hexavalent neptunium nitrate, nitric acid, and a nitrate salting out agent, such as sodium nitrate, by contacting the solution with an organic solvent such as diethyl ether. Subsequently, the neptunium nitrate is extracted from the organic solvent extract phase with water.

  4. Extraction, Scrub, and Strip Test Results for the Salt Waste Processing Facility Caustic Side Solvent Extraction Solvent Sample

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Peters, T. B.

    An Extraction, Scrub, and Strip (ESS) test was performed on a sample of Salt Waste Processing Facility (SWPF) Caustic-Side Solvent Extraction (CSSX) solvent and salt simulant to determine cesium distribution ratios (D( Cs)), and cesium concentration in the strip effluent (SE) and decontaminated salt solution (DSS) streams; this data will be used by Parsons to help determine if the solvent is qualified for use at the SWPF. The ESS test showed acceptable performance of the solvent for extraction, scrub, and strip operations. The extraction D( Cs) measured 12.5, exceeding the required value of 8. This value is consistent with resultsmore » from previous ESS tests using similar solvent formulations. Similarly, scrub and strip cesium distribution ratios fell within acceptable ranges. This revision was created to correct an error. The previous revision used an incorrect set of temperature correction coefficients which resulted in slight deviations from the correct D( Cs) results.« less

  5. The Neuropsychology of Imagery Processing

    DTIC Science & Technology

    1991-01-25

    B. (1985). Agnosia . In K. M. Heilman and E. Valenstein (Eds.), Clinical Neuropsychology. New York: Oxford University Press. Biederman, I. (1987...Campion, J. (1987). Apperceptive agnosia : the specification and description of constructs. In Humphreys, G. W., and Riddoch, M. J. (1987a) (Eds...R. (1986). Disorders of complex visual processing: agnosias , achromatopsia, Balint’s syndrome and related difficulties of orientation and

  6. Biodiesel production by direct transesterification of microalgal biomass with co-solvent.

    PubMed

    Zhang, Yan; Li, Ya; Zhang, Xu; Tan, Tianwei

    2015-11-01

    In this study, a direct transesterification process using 75% ethanol and co-solvent was studied to reduce the energy consumption of lipid extraction process and improve the conversion yield of the microalgae biodiesel. The addition of a certain amount of co-solvent (n-hexane is most preferable) was required for the direct transesterification of microalgae biomass. With the optimal reaction condition of n-hexane to 75% ethanol volume ratio 1:2, mixed solvent dosage 6.0mL, reaction temperature 90°C, reaction time 2.0h and catalyst volume 0.6mL, the direct transesterification process of microalgal biomass resulted in a high conversion yield up to 90.02±0.55wt.%. Copyright © 2015 Elsevier Ltd. All rights reserved.

  7. A microfluidic study of liquid-liquid extraction mediated by carbon dioxide.

    PubMed

    Lestari, Gabriella; Salari, Alinaghi; Abolhasani, Milad; Kumacheva, Eugenia

    2016-07-05

    Liquid-liquid extraction is an important separation and purification method; however, it faces a challenge in reducing the energy consumption and the environmental impact of solvent (extractant) recovery. The reversible chemical reactions of switchable solvents (nitrogenous bases) with carbon dioxide (CO2) can be implemented in reactive liquid-liquid extraction to significantly reduce the cost and energy requirements of solvent recovery. The development of new effective switchable solvents reacting with CO2 and the optimization of extraction conditions rely on the ability to evaluate and screen the performance of switchable solvents in extraction processes. We report a microfluidic strategy for time- and labour-efficient studies of CO2-mediated solvent extraction. The platform utilizes a liquid segment containing an aqueous extractant droplet and a droplet of a solution of a switchable solvent in a non-polar liquid, with gaseous CO2 supplied to the segment from both sides. Following the reaction of the switchable solvent with CO2, the solvent becomes hydrophilic and transfers from the non-polar solvent to the aqueous droplet. By monitoring the time-dependent variation in droplet volumes, we determined the efficiency and extraction time for the CO2-mediated extraction of different nitrogenous bases in a broad experimental parameter space. The platform enables a significant reduction in the amount of switchable solvents used in these studies, provides accurate temporal characterization of the liquid-liquid extraction process, and offers the capability of high-throughput screening of switchable solvents.

  8. Ways to reduce patient turnaround time and improve service quality in emergency departments.

    PubMed

    Sinreich, David; Marmor, Yariv

    2005-01-01

    Recent years have witnessed a fundamental change in the function of emergency departments (EDs). The emphasis of the ED shifts from triage to saving the lives of shock-trauma rooms equipped with state-of-the-art equipment. At the same time walk-in clinics are being set up to treat ambulatory type patients. Simultaneously ED overcrowding has become a common sight in many large urban hospitals. This paper recognises that in order to provide quality treatment to all these patient types, ED process operations have to be flexible and efficient. The paper aims to examine one major benchmark for measuring service quality--patient turnaround time, claiming that in order to provide the quality treatment to which EDs aspire, this time needs to be reduced. This study starts by separating the process each patient type goes through when treated at the ED into unique components. Next, using a simple model, the impact each of these components has on the total patient turnaround time is determined. This in turn, identifies the components that need to be addressed if patient turnaround time is to be streamlined. The model was tested using data that were gathered through a comprehensive time study in six major hospitals. The analysis reveals that waiting time comprises 51-63 per cent of total patient turnaround time in the ED. Its major components are: time away for an x-ray examination; waiting time for the first physician's examination; and waiting time for blood work. The study covers several hospitals and analyses over 20,000 process components; as such the common findings may serve as guidelines to other hospitals when addressing this issue.

  9. Tooth formation - delayed or absent

    MedlinePlus

    ... missing teeth they never developed. Cosmetic or orthodontic dentistry can correct this problem. Causes Specific diseases can ... process. In: Dean JA, ed. McDonald and Avery's Dentistry for the Child and Adolescent . 10th ed. St. ...

  10. An empirical/theoretical model with dimensionless numbers to predict the performance of electrodialysis systems on the basis of operating conditions.

    PubMed

    Karimi, Leila; Ghassemi, Abbas

    2016-07-01

    Among the different technologies developed for desalination, the electrodialysis/electrodialysis reversal (ED/EDR) process is one of the most promising for treating brackish water with low salinity when there is high risk of scaling. Multiple researchers have investigated ED/EDR to optimize the process, determine the effects of operating parameters, and develop theoretical/empirical models. Previously published empirical/theoretical models have evaluated the effect of the hydraulic conditions of the ED/EDR on the limiting current density using dimensionless numbers. The reason for previous studies' emphasis on limiting current density is twofold: 1) to maximize ion removal, most ED/EDR systems are operated close to limiting current conditions if there is not a scaling potential in the concentrate chamber due to a high concentration of less-soluble salts; and 2) for modeling the ED/EDR system with dimensionless numbers, it is more accurate and convenient to use limiting current density, where the boundary layer's characteristics are known at constant electrical conditions. To improve knowledge of ED/EDR systems, ED/EDR models should be also developed for the Ohmic region, where operation reduces energy consumption, facilitates targeted ion removal, and prolongs membrane life compared to limiting current conditions. In this paper, theoretical/empirical models were developed for ED/EDR performance in a wide range of operating conditions. The presented ion removal and selectivity models were developed for the removal of monovalent ions and divalent ions utilizing the dominant dimensionless numbers obtained from laboratory scale electrodialysis experiments. At any system scale, these models can predict ED/EDR performance in terms of monovalent and divalent ion removal. Copyright © 2016 Elsevier Ltd. All rights reserved.

  11. Integrated process for the solvent refining of coal

    DOEpatents

    Garg, Diwakar

    1983-01-01

    A process is set forth for the integrated liquefaction of coal by the catalytic solvent refining of a feed coal in a first stage to liquid and solid products and the catalytic hydrogenation of the solid product in a second stage to produce additional liquid product. A fresh inexpensive, throw-away catalyst is utilized in the second stage hydrogenation of the solid product and this catalyst is recovered and recycled for catalyst duty in the solvent refining stage without any activation steps performed on the used catalyst prior to its use in the solvent refining of feed coal.

  12. Pilot-Scale Silicone Process for Low-Cost Carbon Dioxide Capture Preliminary Techno-Economic Analysis

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Singh, Surinder; Spiry, Irina; Wood, Benjamin

    This report presents system and economic analysis for a carbon-capture unit which uses an aminosilicone-based solvent for CO{sub 2} capture in a pulverized coal (PC) boiler. The aminosilicone solvent is a 60/40 wt/wt mixture of 3-aminopropyl end-capped polydimethylsiloxane (GAP-1m) with tri-ethylene glycol (TEG) as a co-solvent. For comparison purposes, the report also shows results for a carbon-capture unit based on a conventional approach using mono-ethanol amine (MEA). The first year removal cost of CO{sub 2} for the aminosilicone-based carbon-capture process ismore » $46.04/ton of CO2 as compared to $$60.25/ton of CO{sub 2} when MEA is used. The aminosilicone-based process has <77% of the CAPEX of a system using MEA solvent. The lower CAPEX is due to several factors, including the higher working capacity of the aminosilicone solvent compared the MEA, which reduces the solvent flow rate required, reducing equipment sizes. If it is determined that carbon steel can be used in the rich-lean heat exchanger in the carbon capture unit, the first year removal cost of CO{sub 2} decreases to $$44.12/ton. The aminosilicone-based solvent has a higher thermal stability than MEA, allowing desorption to be conducted at higher temperatures and pressures, decreasing the number of compressor stages needed. The aminosilicone-based solvent also has a lower vapor pressure, allowing the desorption to be conducted in a continuous-stirred tank reactor versus a more expensive packed column. The aminosilicone-based solvent has a lower heat capacity, which decreases the heat load on the desorber. In summary, the amino-silicone solvent has significant advantages over conventional systems using MEA.« less

  13. Pilot-Scale Silicone Process for Low-Cost Carbon Dioxide Capture

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Singh, Surinder; Spiry, Irina; Wood, Benjamin

    This report presents system and economicanalysis for a carbon-capture unit which uses an aminosilicone-based solvent for CO₂ capture in a pulverized coal (PC) boiler. The aminosilicone solvent is a 60/40 wt/wt mixture of 3-aminopropyl end-capped polydimethylsiloxane (GAP-1m) with tri-ethylene glycol (TEG) as a co-solvent. Forcomparison purposes, the report also shows results for a carbon-capture unit based on a conventional approach using mono-ethanol amine (MEA). The first year removal cost of CO₂ for the aminosilicone-based carbon-capture process is $46.04/ton of CO₂ as compared to $60.25/ton of CO₂ when MEA is used. The aminosilicone- based process has <77% of the CAPEX ofmore » a system using MEA solvent. The lower CAPEX is due to several factors, including the higher working capacity of the aminosilicone solvent compared the MEA, which reduces the solvent flow rate required, reducing equipment sizes. If it is determined that carbon steel can be used in the rich-lean heat exchanger in the carbon capture unit, the first year removal cost of CO₂ decreases to $44.12/ton. The aminosilicone-based solvent has a higherthermal stability than MEA, allowing desorption to be conducted at higher temperatures and pressures, decreasing the number of compressor stages needed. The aminosilicone-based solvent also has a lowervapor pressure, allowing the desorption to be conducted in a continuous-stirred tank reactor versus a more expensive packed column. The aminosilicone-based solvent has a lowerheat capacity, which decreases the heat load on the desorber. In summary, the amino-silicone solvent has significant advantages overconventional systems using MEA.« less

  14. 21 CFR 177.1650 - Polysulfide polymer-polyepoxy resins.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ...(2-chloroethyl) formal Bis(dichloropropyl) formal Cross-linking agent. Butyl alcohol Solvent. Carbon black (channel process) Chlorinated paraffins Cross-linking agent. Epoxidized linseed oil Epoxidized... monobutyl ether Solvent. Magnesium chloride Methyl isobutyl ketone Solvent. Naphthalene sulfonic acid...

  15. Microporous polymer films and methods of their production

    DOEpatents

    Aubert, James H.

    1995-01-01

    A process for producing thin microporous polymeric films for a variety of uses. The process utilizes a dense gas (liquified gas or supercritical fluid) selected to combine with a solvent-containing polymeric film so that the solvent is dissolved in the dense gas, the polymer is substantially insoluble in the dense gas, and two phases are formed. A microporous film is obtained by removal of a dense gas-solvent phase.

  16. REMOVAL OF PCBS FROM A CONTAMINATED SOIL USING CF-SYSTEMS SOLVENT EXTRACTION PROCESS

    EPA Science Inventory

    The US EPA's START team in cooperation with EPA's SITE program evaluated a pilot scale solvent extraction process developed by CF-Systems. This process uses liquified propane to extract organic contaminants from soils, sludges, and sediments. A pilot-scale evaluation was conducte...

  17. Working memory and semantic involvement in sentence processing: a case of pure progressive amnesia.

    PubMed

    Fossard, Marion; Rigalleau, François; Puel, Michèle; Nespoulous, Jean-Luc; Viallard, Gérard; Démonet, Jean-François; Cardebat, Dominique

    2006-01-01

    ED, a 83-year-old woman, meets the criteria of pure progressive amnesia, with gradual impairment of episodic and autobiographical memory, sparing of semantic processing and strong working memory (WM) deficit. The dissociation between disturbed WM and spared semantic processing permitted testing the role of WM in processing anaphors like pronouns or repeated names. Results showed a globally normal anaphoric behavior in two experiments requiring anaphoric processing in sentence production and comprehension. We suggest that preserved semantic processing in ED would have compensated for working memory deficit in anaphoric processing.

  18. Alternative, Green Processes for the Precision Cleaning of Aerospace Hardware

    NASA Technical Reports Server (NTRS)

    Maloney, Phillip R.; Grandelli, Heather Eilenfield; Devor, Robert; Hintze, Paul E.; Loftin, Kathleen B.; Tomlin, Douglas J.

    2014-01-01

    Precision cleaning is necessary to ensure the proper functioning of aerospace hardware, particularly those systems that come in contact with liquid oxygen or hypergolic fuels. Components that have not been cleaned to the appropriate levels may experience problems ranging from impaired performance to catastrophic failure. Traditionally, this has been achieved using various halogenated solvents. However, as information on the toxicological and/or environmental impacts of each came to light, they were subsequently regulated out of use. The solvent currently used in Kennedy Space Center (KSC) precision cleaning operations is Vertrel MCA. Environmental sampling at KSC indicates that continued use of this or similar solvents may lead to high remediation costs that must be borne by the Program for years to come. In response to this problem, the Green Solvents Project seeks to develop state-of-the-art, green technologies designed to meet KSCs precision cleaning needs.Initially, 23 solvents were identified as potential replacements for the current Vertrel MCA-based process. Highly halogenated solvents were deliberately omitted since historical precedents indicate that as the long-term consequences of these solvents become known, they will eventually be regulated out of practical use, often with significant financial burdens for the user. Three solvent-less cleaning processes (plasma, supercritical carbon dioxide, and carbon dioxide snow) were also chosen since they produce essentially no waste stream. Next, experimental and analytical procedures were developed to compare the relative effectiveness of these solvents and technologies to the current KSC standard of Vertrel MCA. Individually numbered Swagelok fittings were used to represent the hardware in the cleaning process. First, the fittings were cleaned using Vertrel MCA in order to determine their true cleaned mass. Next, the fittings were dipped into stock solutions of five commonly encountered contaminants and were weighed again showing typical contaminant deposition levels of approximately 0.00300g per part. They were then cleaned by the solvent or process being tested and then weighed a third time which allowed for the calculation of the cleaning efficiency of the test solvent or process.Based on preliminary experiments, five solvents (ethanol, isopropanol, acetone, ethyl acetate, and tert-butyl acetate) were down selected for further testing. When coupled with ultrasonic agitation, these solvents removed hydrocarbon contaminants as well as Vertrel MCA and showed improved removal of perfluorinated greases. Supercritical carbon dioxide did an excellent job dissolving each of the five contaminants but did a poor job of removing Teflon particles found in the perfluorinated greases. Plasma cleaning efficiency was found to be dependent on which supply gas was used, exposure time, and gas pressure. Under optimized conditions it was found that breathing air, energized to the plasma phase, was able to remove nearly 100% of the contamination.These findings indicate that alternative cleaning methods are indeed able to achieve precision levels of cleanliness. Currently, our team is working with a commercial cleaning company to get independent verification of our results. We are also evaluating the technical and financial aspects of scaling these processes to a size capable of supporting the future cleaning needs of KSC.

  19. Test Review: Wagner, R. K., Torgesen, J. K., Rashotte, C. A., & Pearson, N. A., "Comprehensive Test of Phonological Processing-2nd Ed. (CTOPP-2)." Austin, Texas: Pro-Ed

    ERIC Educational Resources Information Center

    Dickens, Rachel H.; Meisinger, Elizabeth B.; Tarar, Jessica M.

    2015-01-01

    The Comprehensive Test of Phonological Processing-Second Edition (CTOPP-2; Wagner, Torgesen, Rashotte, & Pearson, 2013) is a norm-referenced test that measures phonological processing skills related to reading for individuals aged 4 to 24. According to its authors, the CTOPP-2 may be used to identify individuals who are markedly below their…

  20. Sequential elution process

    DOEpatents

    Kingsley, I.S.

    1987-01-06

    A process and apparatus are disclosed for the separation of complex mixtures of carbonaceous material by sequential elution with successively stronger solvents. In the process, a column containing glass beads is maintained in a fluidized state by a rapidly flowing stream of a weak solvent, and the sample is injected into this flowing stream such that a portion of the sample is dissolved therein and the remainder of the sample is precipitated therein and collected as a uniform deposit on the glass beads. Successively stronger solvents are then passed through the column to sequentially elute less soluble materials. 1 fig.

  1. How High Pressure Unifies Solvation Processes in Liquid Chromatography.

    PubMed

    Bocian, Szymon; Škrinjar, Tea; Bolanca, Tomislav; Buszewski, Bogusław

    2017-11-01

    A series of core-shell-based stationary phases of varying surface chemistry were subjected to solvent adsorption investigation under ultra-HPLC conditions. Acetonitrile and water excess isotherms were measured using a minor disturbance method. It was observed that adsorption of organic solvent is unified under high pressure. Preferential solvation due to specific interactions between the stationary phases and solvent molecules was limited. The obtained results showed that the solvation process is almost independent of surface chemistry, in contrast to HPLC conditions in which specific interactions differentiate solvation processes.

  2. Energy efficient solvent regeneration process for carbon dioxide capture

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Zhou, Shaojun; Meyer, Howard S.; Li, Shiguang

    A process for removing carbon dioxide from a carbon dioxide-loaded solvent uses two stages of flash apparatus. Carbon dioxide is flashed from the solvent at a higher temperature and pressure in the first stage, and a lower temperature and pressure in the second stage, and is fed to a multi-stage compression train for high pressure liquefaction. Because some of the carbon dioxide fed to the compression train is already under pressure, less energy is required to further compress the carbon dioxide to a liquid state, compared to conventional processes.

  3. Acoustic-Phonetic Versus Lexical Processing in Nonnative Listeners Differing in Their Dominant Language.

    PubMed

    Shi, Lu-Feng; Koenig, Laura L

    2016-09-01

    Nonnative listeners have difficulty recognizing English words due to underdeveloped acoustic-phonetic and/or lexical skills. The present study used Boothroyd and Nittrouer's (1988)j factor to tease apart these two components of word recognition. Participants included 15 native English and 29 native Russian listeners. Fourteen and 15 of the Russian listeners reported English (ED) and Russian (RD) to be their dominant language, respectively. Listeners were presented 119 consonant-vowel-consonant real and nonsense words in speech-spectrum noise at +6 dB SNR. Responses were scored for word and phoneme recognition, the logarithmic quotient of which yielded j. Word and phoneme recognition was comparable between native and ED listeners but poorer in RD listeners. Analysis of j indicated less effective use of lexical information in RD than in native and ED listeners. Lexical processing was strongly correlated with the length of residence in the United States. Language background is important for nonnative word recognition. Lexical skills can be regarded as nativelike in ED nonnative listeners. Compromised word recognition in ED listeners is unlikely a result of poor lexical processing. Performance should be interpreted with caution for listeners dominant in their first language, whose word recognition is affected by both lexical and acoustic-phonetic factors.

  4. Process improvement to enhance existing stroke team activity toward more timely thrombolytic treatment.

    PubMed

    Cho, Han-Jin; Lee, Kyung Yul; Nam, Hyo Suk; Kim, Young Dae; Song, Tae-Jin; Jung, Yo Han; Choi, Hye-Yeon; Heo, Ji Hoe

    2014-10-01

    Process improvement (PI) is an approach for enhancing the existing quality improvement process by making changes while keeping the existing process. We have shown that implementation of a stroke code program using a computerized physician order entry system is effective in reducing the in-hospital time delay to thrombolysis in acute stroke patients. We investigated whether implementation of this PI could further reduce the time delays by continuous improvement of the existing process. After determining a key indicator [time interval from emergency department (ED) arrival to intravenous (IV) thrombolysis] and conducting data analysis, the target time from ED arrival to IV thrombolysis in acute stroke patients was set at 40 min. The key indicator was monitored continuously at a weekly stroke conference. The possible reasons for the delay were determined in cases for which IV thrombolysis was not administered within the target time and, where possible, the problems were corrected. The time intervals from ED arrival to the various evaluation steps and treatment before and after implementation of the PI were compared. The median time interval from ED arrival to IV thrombolysis in acute stroke patients was significantly reduced after implementation of the PI (from 63.5 to 45 min, p=0.001). The variation in the time interval was also reduced. A reduction in the evaluation time intervals was achieved after the PI [from 23 to 17 min for computed tomography scanning (p=0.003) and from 35 to 29 min for complete blood counts (p=0.006)]. PI is effective for continuous improvement of the existing process by reducing the time delays between ED arrival and IV thrombolysis in acute stroke patients.

  5. Toward reliable and repeatable automated STEM-EDS metrology with high throughput

    NASA Astrophysics Data System (ADS)

    Zhong, Zhenxin; Donald, Jason; Dutrow, Gavin; Roller, Justin; Ugurlu, Ozan; Verheijen, Martin; Bidiuk, Oleksii

    2018-03-01

    New materials and designs in complex 3D architectures in logic and memory devices have raised complexity in S/TEM metrology. In this paper, we report about a newly developed, automated, scanning transmission electron microscopy (STEM) based, energy dispersive X-ray spectroscopy (STEM-EDS) metrology method that addresses these challenges. Different methodologies toward repeatable and efficient, automated STEM-EDS metrology with high throughput are presented: we introduce the best known auto-EDS acquisition and quantification methods for robust and reliable metrology and present how electron exposure dose impacts the EDS metrology reproducibility, either due to poor signalto-noise ratio (SNR) at low dose or due to sample modifications at high dose conditions. Finally, we discuss the limitations of the STEM-EDS metrology technique and propose strategies to optimize the process both in terms of throughput and metrology reliability.

  6. Assessing rumination in eating disorders: principal component analysis of a minimally modified ruminative response scale.

    PubMed

    Cowdrey, Felicity A; Park, Rebecca J

    2011-12-01

    A process account of eating disorders (EDs) (Park et al., in press-a) proposes that preoccupation with ruminative themes of eating, weight and shape may be important in ED maintenance. No self-report measure exists to capture disorder-specific rumination in EDs. 275 healthy participants rated rumination items and completed self-report measures of ED symptoms, depression and anxiety. Principal component analysis revealed two factors, reflection and brooding. The final nine-item Ruminative Response Scale for Eating Disorders (RRS-ED) demonstrated good convergent and discriminant validity and test-retest reliability. The psychometric properties were replicated in an anorexia nervosa sample. The findings support the notion that rumination in EDs is distinct from rumination in depression and is not adequately captured by existing measures. Copyright © 2011 Elsevier Ltd. All rights reserved.

  7. Membrane augmented distillation to separate solvents from water

    DOEpatents

    Huang, Yu; Baker, Richard W.; Daniels, Rami; Aldajani, Tiem; Ly, Jennifer H.; Alvarez, Franklin R.; Vane, Leland M.

    2012-09-11

    Processes for removing water from organic solvents, such as ethanol. The processes include distillation to form a rectified overhead vapor, compression of the rectified vapor, and treatment of the compressed vapor by two sequential membrane separation steps.

  8. Organic electronic devices with multiple solution-processed layers

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Forrest, Stephen R.; Lassiter, Brian E.; Zimmerman, Jeramy D.

    2016-07-05

    A method for fabricating an organic light emitting device stack involves depositing a first conductive electrode layer over a substrate; depositing a first set of one or more organic layers, wherein at least one of the first set of organic layers is a first emissive layer and one of the first set of organic layers is deposited by a solution-based process that utilizes a first solvent; depositing a first conductive interlayer by a dry deposition process; and depositing a second set of one or more organic layers, wherein at least one of the second set of organic layers is amore » second emissive layer and one of the second set of organic layers is deposited by a solution-based process that utilizes a second solvent, wherein all layers that precede the layer deposited using the second solvent are insoluble in the second solvent.« less

  9. What constitutes a good hand offs in the emergency department: a patient's perspective.

    PubMed

    Downey, La Vonne; Zun, Leslie; Burke, Trena

    2013-01-01

    The aim is to determine, from the patient's perspective, what constitutes a good hand-off procedure in the emergency department (ED). The secondary purpose is to evaluate what impact a formalized hand-off had on patient knowledge, throughput and customer service This study used a randomized controlled clinical trial involving two unique hand-off approaches and a convenience sample. The study alternated between the current hand-off process that documented the process but not specific elements (referred to as the informal process) to one using the IPASS the BATON process (considered the formal process). Consenting patients completed a 12-question validated questionnaire on how the process was perceived by patients and about their understanding why they waited in the ED. Statistical analysis using SPSS calculated descriptive frequencies and t-tests. In total 107 patients were enrolled: 50 in the informal and 57 in the formal group. Most patients had positive answers to the customer survey. There were significant differences between formal and informal groups: recalling the oncoming and outgoing physician coming to the patient's bed (p = 0.000), with more formal group recalling that than informal group patients; the oncoming physician introducing him/herself (p = 0.01), with more from the formal group answering yes and the physician discussing tests and implications with formal group patients (p = 0.02). This study was done at an urban inner city ED, a fact that may have skewed its results. A comparison of suburban and rural EDs would make the results stronger. It also reflected a very high level of customer satisfaction within the ED. This lack of variance may have meant that the correlation between customer service and handoffs was missed or underrepresented. There was no codified observation of either those using the IPASS the BATON script or those using informal procedures, so no comparison of level and types of information given between the two groups was done. There could have been a bias of those attending who had internalized the IPASS the BATON procedures and used them even when they were assigned to the informal group. A hand off from one physician to the next in the emergency department is best done using a formalized process. IPASS the BATON is a useful tool for hand off in the ED in part because it involved the patient in the process. The formal hand off increased communication between patient and doctor as its use increased the patient's opportunity to ask and respond to questions. The researchers evaluated an ED physician specific hand-off process and illustrate the value and impact of involving patients in the hand-off process.

  10. Applying Lean: Implementation of a Rapid Triage and Treatment System

    PubMed Central

    Murrell, Karen L.; Offerman, Steven R.; Kauffman, Mark B.

    2011-01-01

    Objective: Emergency department (ED) crowding creates issues with patient satisfaction, long wait times and leaving the ED without being seen by a doctor (LWBS). Our objective was to evaluate how applying Lean principles to develop a Rapid Triage and Treatment (RTT) system affected ED metrics in our community hospital. Methods: Using Lean principles, we made ED process improvements that led to the RTT system. Using this system, patients undergo a rapid triage with low-acuity patients seen and treated by a physician in the triage area. No changes in staffing, physical space or hospital resources occurred during the study period. We then performed a retrospective, observational study comparing hospital electronic medical record data six months before and six months after implementation of the RTT system. Results: ED census was 30,981 in the six months prior to RTT and 33,926 after. Ambulance arrivals, ED patient acuity and hospital admission rates were unchanged throughout the study periods. Mean ED length of stay was longer in the period before RTT (4.2 hours, 95% confidence interval [CI] = 4.2–4.3; standard deviation [SD] = 3.9) than after (3.6 hours, 95% CI = 3.6–3.7; SD = 3.7). Mean ED arrival to physician start time was 62.2 minutes (95% CI = 61.5–63.0; SD = 58.9) prior to RTT and 41.9 minutes (95% CI = 41.5–42.4; SD = 30.9) after. The LWBS rate for the six months prior to RTT was 4.5% (95% CI = 3.1–5.5) and 1.5% (95% CI = 0.6–1.8) after RTT initiation. Conclusion: Our experience shows that changes in ED processes using Lean thinking and available resources can improve efficiency. In this community hospital ED, use of an RTT system decreased patient wait times and LWBS rates. PMID:21691524

  11. Notification Event Architecture for Traveler Screening: Predictive Traveler Screening Using Event Driven Business Process Management

    ERIC Educational Resources Information Center

    Lynch, John Kenneth

    2013-01-01

    Using an exploratory model of the 9/11 terrorists, this research investigates the linkages between Event Driven Business Process Management (edBPM) and decision making. Although the literature on the role of technology in efficient and effective decision making is extensive, research has yet to quantify the benefit of using edBPM to aid the…

  12. Collaborating with Youth to Inform and Develop Tools for Psychotropic Decision Making

    PubMed Central

    Murphy, Andrea; Gardner, David; Kutcher, Stan; Davidson, Simon; Manion, Ian

    2010-01-01

    Introduction: Youth oriented and informed resources designed to support psychopharmacotherapeutic decision-making are essentially unavailable. This article outlines the approach taken to design such resources, the product that resulted from the approach taken, and the lessons learned from the process. Methods: A project team with psychopharmacology expertise was assembled. The project team reviewed best practices regarding medication educational materials and related tools to support decisions. Collaboration with key stakeholders who were thought of as primary end-users and target groups occurred. A graphic designer and a plain language consultant were also retained. Results: Through an iterative and collaborative process over approximately 6 months, Med Ed and Med Ed Passport were developed. Literature and input from key stakeholders, in particular youth, was instrumental to the development of the tools and materials within Med Ed. A training program utilizing a train-the-trainer model was developed to facilitate the implementation of Med Ed in Ontario, which is currently ongoing. Conclusion: An evidence-informed process that includes youth and key stakeholder engagement is required for developing tools to support in psychopharmacotherapeutic decision-making. The development process fostered an environment of reciprocity between the project team and key stakeholders. PMID:21037916

  13. Microporous polymer films and methods of their production

    DOEpatents

    Aubert, J.H.

    1995-06-06

    A process is described for producing thin microporous polymeric films for a variety of uses. The process utilizes a dense gas (liquefied gas or supercritical fluid) selected to combine with a solvent-containing polymeric film so that the solvent is dissolved in the dense gas, the polymer is substantially insoluble in the dense gas, and two phases are formed. A microporous film is obtained by removal of a dense gas-solvent phase. 9 figs.

  14. Effect of pH on desorption of CO2 from alkanolamine - rich solvents

    NASA Astrophysics Data System (ADS)

    Du, Min

    2017-08-01

    Adipic acid was used as a pH regulator, which was added to 0.4 mol/L MEA, DEA and MDEA solvents during CO2 desorption process. It is found that when pH value of the solvents swing between 8-10, CO2 desorption rate enhanced, and energy consumption has declined obviously. This research may have reference significance on optimization of alkanolamine CO2 capture process.

  15. Towards ultra-fast solvent evaporation, the development of a computer controlled solvent vapor annealing chamber

    NASA Astrophysics Data System (ADS)

    Nelson, Gunnar; Wong, J.; Drapes, C.; Grant, M.; Baruth, A.

    Despite the promise of cheap and fast nanoscale ordering of block polymer thin films via solvent vapor annealing, a standardized, scalable production scheme remains elusive. Solvent vapor annealing exposes a nano-thin film to the vapors of one or more solvents with the goal of forming a swollen and mobile state to direct the self-assembly process by tuning surface energies and mediating unfavorable chain interactions. We have shown that optimized annealing conditions, where kinetic and thermal properties for crystal growth are extremely fast (<1s), exist at solvent concentrations just below the order-disorder transition of the film. However, when investigating the propagation of a given morphology into the bulk of a film during drying, the role of solvent evaporation comes under great scrutiny. During this process, the film undergoes a competition between two fronts; phase separation and kinetic trapping. Recent results in both theory and experiment point toward this critical element in controlling the resultant morphologies; however, no current method includes a controllable solvent evaporation rate at ultra-fast time scales. We report on a computer-controlled, pneumatically actuated chamber that provides control over solvent evaporation down to 15 ms. Furthermore, in situ spectral reflectance monitors solvent concentration with 10 ms temporal resolution and reveals several possible evaporation trajectories, ranging from linear to exponential to logarithmic. Funded by Dr. Randolph Ferlic Summer Research Scholarship and NASA Nebraska Space Grant.

  16. A theoretical thermochemical study of solute-solvent dielectric effects in the displacement of codon-anticodon base pairs

    NASA Astrophysics Data System (ADS)

    Monajjemi, M.; Razavian, M. H.; Mollaamin, F.; Naderi, F.; Honarparvar, B.

    2008-12-01

    Quantum-chemical solvent effect theories describe the electronic structure of a molecular subsystem embedded in a solvent or other molecular environment. The solvation of biomolecules is important in molecular biology, since numerous processes involve proteins interacting in changing solvent-solute systems. In this theoretical study, we focus on mRNA-tRNA base pairs as a fundamental step in protein synthesis influenced by hydrogen bonding between two antiparallel trinucleotides, namely, the mRNA codon and tRNA anticodon. We use the mean reaction field theories, which describe electrostatic and polarization interactions between solute and solvent in the AAA, UUU, AAG, and UUC triplex sequences optimized in various solvent media such as water, dimethylsulfoxide, methanol, ethanol, and cyclopean using the self-consistent reaction field model. This process depends on either the reaction potential function of the solvent or charge transfer operators that appear in solute-solvent interaction. Because of codon and anticodon biological criteria, we performed nonempirical quantum-mechanical calculations at the BLYP and B3LYP/3-21G, 6-31G, and 6-31G* levels of theory in the gas phase and five solvents at three temperatures. Finally, to obtain more information, we calculated thermochemical parameters to find that the dielectric constant of solvents plays an important role in the displacement of amino acid sequences on codon-anticodon residues in proteins, which can cause some mutations in humans.

  17. Rational enhancement of enzyme performance in organic solvents. Final technical report, 1992--1996

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Klibanov, A.M.

    1996-12-31

    This research focused on the following: the dependence of enzymatic activity of several model hydrolases in nonaqueous solvents; control of substrate selectivity of the protease subtilisin Carlsberg by the solvent; control of catalytic activity and enantioselectivity of this enzyme in organic solvents by immobilization support; lipase-catalyzed acylation of sugars in anhydrous hydrophobic media; the possibility of accelerating enzymatic processes in organic solvents by certain cosolvents; whether lipase catalysis in organic solvents can be enhanced by introducing interfaces in the in the reaction medium; the structure of proteins suspended in organic solvents; improving enzymatic enantioselectivity in organic solvents; analyzing the plungemore » in enzymatic activity upon replacing water with organic solvents; and the structural basis for the phenomenon of molecular memory of imprinted proteins in organic solvents.« less

  18. The study of membrane formation via phase inversion method by cloud point and light scattering experiment

    NASA Astrophysics Data System (ADS)

    Arahman, Nasrul; Maimun, Teuku; Mukramah, Syawaliah

    2017-01-01

    The composition of polymer solution and the methods of membrane preparation determine the solidification process of membrane. The formation of membrane structure prepared via non-solvent induced phase separation (NIPS) method is mostly determined by phase separation process between polymer, solvent, and non-solvent. This paper discusses the phase separation process of polymer solution containing Polyethersulfone (PES), N-methylpirrolidone (NMP), and surfactant Tetronic 1307 (Tet). Cloud point experiment is conducted to determine the amount of non-solvent needed on induced phase separation. Amount of water required as a non-solvent decreases by the addition of surfactant Tet. Kinetics of phase separation for such system is studied by the light scattering measurement. With the addition of Tet., the delayed phase separation is observed and the structure growth rate decreases. Moreover, the morphology of fabricated membrane from those polymer systems is analyzed by scanning electron microscopy (SEM). The images of both systems show the formation of finger-like macrovoids through the cross-section.

  19. Solvent-induced controllable synthesis, single-crystal to single-crystal transformation and encapsulation of Alq3 for modulated luminescence in (4,8)-connected metal-organic frameworks.

    PubMed

    Lan, Ya-Qian; Jiang, Hai-Long; Li, Shun-Li; Xu, Qiang

    2012-07-16

    In this work, for the first time, we have systematically demonstrated that solvent plays crucial roles in both controllable synthesis of metal-organic frameworks (MOFs) and their structural transformation process. With solvent as the only variable, five new MOFs with different structures have been constructed, in which one MOF undergoes solvent-induced single-crystal to single-crystal (SCSC) transformation that involves not only solvent exchange but also the cleavage and formation of coordination bonds. Particularly, a significant crystallographic change has been realized through an unprecedented three-step SCSC transformation process. Furthermore, we have demonstrated that the obtained MOF could be an excellent host for chromophores such as Alq3 for modulated luminescent properties.

  20. Low-Temperature, Solution-Processed, Transparent Zinc Oxide-Based Thin-Film Transistors for Sensing Various Solvents.

    PubMed

    You, Hsin-Chiang; Wang, Cheng-Jyun

    2017-02-26

    A low temperature solution-processed thin-film transistor (TFT) using zinc oxide (ZnO) film as an exposed sensing semiconductor channel was fabricated to detect and identify various solution solvents. The TFT devices would offer applications for low-cost, rapid and highly compatible water-soluble detection and could replace conventional silicon field effect transistors (FETs) as bio-sensors. In this work, we demonstrate the utility of the TFT ZnO channel to sense various liquids, such as polar solvents (ethanol), non-polar solvents (toluene) and deionized (DI) water, which were dropped and adsorbed onto the channel. It is discussed how different dielectric constants of polar/non-polar solvents and DI water were associated with various charge transport properties, demonstrating the main detection mechanisms of the thin-film transistor.

  1. New guidelines for geriatric EDs: guidance focused on boosting environment, care processes.

    PubMed

    2014-05-01

    A cadre of prominent medical groups, including the ACEP, ENA, AGS, and SAEM, has unveiled a comprehensive set of Geriatric Emergency Department Guidelines to aid hospitals that are either in the process of opening senior-focused EDs or revamping their policies and procedures to better meet the needs of an aging population. The guidelines offer recommendations related to staffing, infrastructure, education, and transition-of-care strategies. In addition, they outline a host of screenings that studies have shown are beneficial for older adults. Experts note that hospital systems around the country have already opened 50 geriatric EDs, with many more facilities in development. Guideline authors state that the guidelines take an evidence-based approach to managing senior patients. While more cost and outcomes data are needed, experts say that senior-focused improvements to emergency care can reduce admissions and return visits to the ED while also boosting patient satisfaction. Future efforts will focus on prioritizing the guideline recommendations so that ED administrators concerned with improving senior care will tackle the most important changes first.

  2. Using GC-FID to Quantify the Removal of 4-sec-Butylphenol from NGS Solvent by NaOH

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Sloop, Jr., Frederick V.; Moyer, Bruce A.

    2014-12-01

    A caustic wash of the solvent used in the Next-Generation Caustic-Side Solvent Extraction (NG-CSSX) process was found to remove the modifier breakdown product 4-sec-butylphenol (SBP) with varying efficiency depending on the aqueous NaOH concentration. Recent efforts at ORNL have aimed at characterizing the flowsheet chemistry and reducing the technical uncertainties of the NG-CSSX process. One technical uncertainty has been the efficacy of caustic washing of the solvent for the removal of lipophilic anions, in particular, the efficient removal of SBP, an important degradation product of the solvent modifier, Cs-7SB. In order to make this determination, it was necessary to developmore » a sensitive and reliable analytical technique for the detection and quantitation of SBP. This report recounts the development of a GC-FID-based (Gas Chromatography Flame Ionization Detection) technique for analyzing SBP and the utilization of the technique to subsequently confirm the ability of the caustic wash to efficiently remove SBP from the Next Generation Solvent (NGS) used in NG-CSSX. In particular, the developed technique was used to monitor the amount of SBP removed from a simple solvent and the full NGS by contact with sodium hydroxide wash solutions over a range of concentrations. The results show that caustic washing removes SBP with effectively the same efficiency as it did in the original Caustic-Side Solvent Extraction (CSSX) process.« less

  3. Highly efficient secondary dewatering of dewatered sewage sludge using low boiling point solvents.

    PubMed

    He, Chao; Chena, Chia-Lung; Xu, Zhirong; Wang, Jing-Yuan

    2014-01-01

    Secondary dewatering of dewatered sludge is imperative to make conventional drying and incineration of sludge more economically feasible. In this study, a secondary dewatering of dewatered sludge with selected solvents (i.e. acetone and ethanol) followed by vacuum filtration and nature drying was investigated to achieve in-depth dewatering. After the entire secondary dewatering process, the sludge was shown to be odourless and the organic matter content was greatly retained. Increased mean particle size of sludge after solvent contact improved solid-liquid separation. With an acetone/sludge ratio of 3:1 (mL:g) in solvent contact and subsequent nature drying at ambient temperature after 24 h, the moisture content of sludge can be reduced to a level less than 20%. It is found that the polysaccharides were mainly precipitated by acetone, whereas the release ratios of protein and DNA were increased significantly as the added acetone volumes were elevated. During nature drying, accumulated evaporation rates of the sludge after solvent contact were 5-6 times higher than original dewatered sludge. Furthermore, sludge after acetone contact had better nature drying performance than ethanol. The two-stage dewatering involves solvent contact dewatering and solvent enhanced evaporation dewatering. Through selecting an appropriate solvent/sludge ratio as well as economical solvents and minimizing the solvent loss in a closed-pilot system, this dewatering process can be competitive in industrial applications. Therefore, this solvent-aided secondary dewatering is an energy-saving technology for effective in-depth dewatering of dewatered sludge and subsequent sludge utilization.

  4. Approximately 800-nm-Thick Pinhole-Free Perovskite Films via Facile Solvent Retarding Process for Efficient Planar Solar Cells.

    PubMed

    Yuan, Zhongcheng; Yang, Yingguo; Wu, Zhongwei; Bai, Sai; Xu, Weidong; Song, Tao; Gao, Xingyu; Gao, Feng; Sun, Baoquan

    2016-12-21

    Device performance of organometal halide perovskite solar cells significantly depends on the quality and thickness of perovskite absorber films. However, conventional deposition methods often generate pinholes within ∼300 nm-thick perovskite films, which are detrimental to the large area device manufacture. Here we demonstrated a simple solvent retarding process to deposit uniform pinhole free perovskite films with thicknesses up to ∼800 nm. Solvent evaporation during the retarding process facilitated the components separation in the mixed halide perovskite precursors, and hence the final films exhibited pinhole free morphology and large grain sizes. In addition, the increased precursor concentration after solvent-retarding process led to thick perovskite films. Based on the uniform and thick perovskite films prepared by this convenient process, a champion device efficiency up to 16.8% was achieved. We believe that this simple deposition procedure for high quality perovskite films around micrometer thickness has a great potential in the application of large area perovskite solar cells and other optoelectronic devices.

  5. Recrystallization of fluconazole using the supercritical antisolvent (SAS) process.

    PubMed

    Park, Hee Jun; Kim, Min-Soo; Lee, Sibeum; Kim, Jeong-Soo; Woo, Jong-Soo; Park, Jeong-Sook; Hwang, Sung-Joo

    2007-01-10

    The supercritical antisolvent (SAS) process was used to modify solid state characteristics of fluconazole. Fluconazole was recrystallized at various temperatures (60-80 degrees C) and pressures (8-16MPa) using dichloromethane (DCM) as a solvent. Acetone and ethanol were also employed as solvents. The fluconazole polymorphs prepared by the SAS process were characterized by differential scanning calorimetry (DSC), thermogravimetry analysis (TGA), powder X-ray diffraction (PXRD), Fourier transform infrared spectroscopy (FT-IR) and scanning electron microscopy (SEM). Furthermore, the equilibrium solubility of the samples in aqueous solution was determined. Fluconazole anhydrate form I was obtained at low temperature (40 degrees C) and anhydrate form II was obtained at high temperature (80 degrees C). The variation of pressure during the SAS process may influence the preferred orientation. Anhydrate forms I and II were also obtained using various solvents. Therefore, it was shown that solid state characteristics of fluconazole, including the polymorphic form and preferred orientation, can be controlled by changing operating conditions of the SAS process such as temperature, pressure, and solvent.

  6. Supercritical-Multiple-Solvent Extraction From Coal

    NASA Technical Reports Server (NTRS)

    Corcoran, W.; Fong, W.; Pichaichanarong, P.; Chan, P.; Lawson, D.

    1983-01-01

    Large and small molecules dissolve different constituents. Experimental apparatus used to test supercritical extraction of hydrogen rich compounds from coal in various organic solvents. In decreasing order of importance, relevant process parameters were found to be temperature, solvent type, pressure, and residence time.

  7. Use of normal propyl bromide solvents for extraction and recovery of asphalt cements

    DOT National Transportation Integrated Search

    2000-11-01

    Four normal propyl bromide (nPB) solvents were evaluated for use as chlorinated solvent replacements in typical hot mix asphalt (HMA) extraction and recovery processes. The experimental design included one method of extraction (centrifuge), one metho...

  8. 40 CFR 63.2854 - How do I determine the weighted average volume fraction of HAP in the actual solvent loss?

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Extraction for Vegetable Oil Production Compliance Requirements § 63.2854 How do I determine the weighted... received for use in your vegetable oil production process. By the end of each calendar month following an... the solvent in each delivery of solvent, including solvent recovered from off-site oil. To determine...

  9. 40 CFR 63.2854 - How do I determine the weighted average volume fraction of HAP in the actual solvent loss?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Extraction for Vegetable Oil Production Compliance Requirements § 63.2854 How do I determine the weighted... received for use in your vegetable oil production process. By the end of each calendar month following an... the solvent in each delivery of solvent, including solvent recovered from off-site oil. To determine...

  10. The unsafe haven: Eating disorders as attachment relationships.

    PubMed

    Forsén Mantilla, Emma; Clinton, David; Birgegård, Andreas

    2018-05-21

    Some patients with eating disorders (EDs) seem to experience their illness as an entity, a symbolic other to whom they relate, and which may influence both symptom levels and self-image. Extending previous research, this study investigated whether the patient-ED relationship has attachment qualities. Structural Analysis of Social Behaviour was used to operationalize the patient-ED relationship, and the Attachment Style Questionnaire was used to measure attachment. We examined ED patients' (N = 148) relationship with their ED, attachment behaviour, symptoms, and self-image. Attachment dimensions of Confidence, Anxious/ambivalence, and Avoidance were found to be significantly correlated with aspects of the patient-ED relationship. Introjection (i.e., whether ED actions were incorporated into patients' self-image) was investigated by examining the match between self-image profiles and the actions of patients' EDs. A double mediation model was tested in which ED control/emancipation and patients' Self-blame mediated the effect of attachment security on ED symptoms. Attachment insecurity was associated with greater ED control and patient submission. In 28.5% of patients, there was a high degree of correlation between self-image and ED action profile. Data supported the mediation model. Attachment processes appear to be associated with the manner in which ED patients relate to their disorder, at least in some cases. Attempts to maintain psychological proximity to the ED as an introjected attachment figure may help to explain treatment resistance and ambivalence about change. This perspective may be useful in treatment. Attachment behaviours are associated with the patient-ED relationship, in which attachment insecurity is correlated with greater eating disorder control and patient submission. Some patients seem to incorporate the actions of the ED in their self-image, suggesting the presence of introjection. The patient-ED relationship may help explain patients' anxiety and ambivalence about change, seen from an attachment perspective. In treatment, it may be important to explore alternative safe havens and secure bases to the ED, such as interpersonal relationships and activities. © 2018 The British Psychological Society.

  11. Pediatric Emergency Department Resource Utilization among Children with Primary Care Clinic Contact in the Preceding 2 Days: A Cross-Sectional Study.

    PubMed

    Grech, Christina K; Laux, Molly A; Burrows, Heather L; Macy, Michelle L; Pomeranz, Elaine S

    2017-09-01

    To characterize pediatric patient contacts with their primary care clinic in the 2 days preceding a visit to the emergency department (ED) and explore how the type of clinic contact relates to ED resource use. We conducted a retrospective chart review of 368 pediatric ED visits in the first 7 days of each month, from September 2012 to August 2013. Visits were included if the family contacted their child's general pediatric clinic in the study health system in the 2 days preceding the ED visit. Descriptive statistics were calculated. Primary outcomes were ED resource use (tests, treatments) and disposition (admission or discharge). Outcomes by type of clinic contact were compared with χ 2 statistics. Of 1116 records with ED visits in the 12 study weeks extracted from the electronic medical record, 368 ED visits met inclusion criteria. Most ED visits followed a single clinic contact (78.8%). Of the 474 clinic contacts, 149 were in-person visits, 216 phone calls when clinic was open, and 109 phone calls when clinic was closed. ED visits that followed an in-person clinic contact with advice to go to the ED had significantly greater rates of testing and admission than those advised to go to the ED after phone contact and those never advised to go to the ED. In-person clinic visits with advice to go to the ED were associated with the greatest ED resource use. Limitations include a study of a single health system without a uniform process for triaging patients to the ED across clinics. Copyright © 2017 Elsevier Inc. All rights reserved.

  12. Studies of the effect of selected nondonor solvents on coal liquefaction yields

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Jolley, R. L.; Rodgers, B. R.; Benjamin, B. M.

    The objective of this research program was to evaluate the effectiveness of selected nondonor solvents (i.e., solvents that are not generally considered to have hydrogen available for hydrogenolysis reactions) for the solubilization of coals. Principal criteria for selection of candidate solvents were that the compound should be representative of a major chemical class, should be present in reasonable concentration in coal liquid products, and should have the potential to participate in hydrogen redistribution reactions. Naphthalene, phenanthrene, pyrene, carbazole, phenanthridine, quinoline, 1-naphthol, and diphenyl ether were evaluated to determine their effect on coal liquefaction yields and were compared with phenol andmore » two high-quality process solvents, Wilsonville SRC-I recycle solvent and Lummus ITSL heavy oil solvent. The high conversion efficacy of 1-naphthol may be attributed to its condensation to binaphthol and the consequent availability of hydrogen. The effectiveness of both the nitrogen heterocycles and the polycyclic aromatic hydrocarbon (PAH) compounds may be due to their polycyclic aromatic nature (i.e., possible hydrogen shuttling or transfer agents) and their physical solvent properties. The relative effectiveness for coal conversion of the Lummus ITSL heavy oil solvent as compared with the Wilsonville SRC-I process solvent may be attributed to the much higher concentration of 3-, 4-, and 5-ring PAH and hydroaromatic constituents in Lummus solvent. The chemistry of coal liquefaction and the development of recycle, hydrogen donor, and nondonor solvents are reviewed. The experimental methodology for tubing-bomb tests is outlined, and experimental problem areas are discussed.« less

  13. Web-Based Predictive Analytics to Improve Patient Flow in the Emergency Department

    NASA Technical Reports Server (NTRS)

    Buckler, David L.

    2012-01-01

    The Emergency Department (ED) simulation project was established to demonstrate how requirements-driven analysis and process simulation can help improve the quality of patient care for the Veterans Health Administration's (VHA) Veterans Affairs Medical Centers (VAMC). This project developed a web-based simulation prototype of patient flow in EDs, validated the performance of the simulation against operational data, and documented IT requirements for the ED simulation.

  14. Quantitative proteomics of the human skin secretome reveal a reduction in immune defense mediators in ectodermal dysplasia patients.

    PubMed

    Burian, Marc; Velic, Ana; Matic, Katarina; Günther, Stephanie; Kraft, Beatrice; Gonser, Lena; Forchhammer, Stephan; Tiffert, Yvonne; Naumer, Christian; Krohn, Michael; Berneburg, Mark; Yazdi, Amir S; Maček, Boris; Schittek, Birgit

    2015-03-01

    In healthy human skin host defense molecules such as antimicrobial peptides (AMPs) contribute to skin immune homeostasis. In patients with the congenital disease ectodermal dysplasia (ED) skin integrity is disturbed and as a result patients have recurrent skin infections. The disease is characterized by developmental abnormalities of ectodermal derivatives and absent or reduced sweating. We hypothesized that ED patients have a reduced skin immune defense because of the reduced ability to sweat. Therefore, we performed a label-free quantitative proteome analysis of wash solution of human skin from ED patients or healthy individuals. A clear-cut difference between both cohorts could be observed in cellular processes related to immunity and host defense. In line with the extensive underrepresentation of proteins of the immune system, dermcidin, a sweat-derived AMP, was reduced in its abundance in the skin secretome of ED patients. In contrast, proteins involved in metabolic/catabolic and biosynthetic processes were enriched in the skin secretome of ED patients. In summary, our proteome profiling provides insights into the actual situation of healthy versus diseased skin. The systematic reduction in immune system and defense-related proteins may contribute to the high susceptibility of ED patients to skin infections and altered skin colonization.

  15. Requirements and Recommendations for Learning Strategies in the U.S. Army Basic Skills Education Program.

    DTIC Science & Technology

    1980-11-30

    of processing , the greater the retention in long term memory (see Butter- field, Wambold, & Belmont, 1968; Craik and Lockhart , 1972). Interestingly...L.S., & Craik , F.I.M. (Eds.) Levels of processing in human memory. Hillsdale, NJ: Erlbaum, 1979. Chicago Board of Education. Chicago Mastery Learning...Child Psychology, 1973, 15, 169-186. Lockhart , R.S., Craik , F.I.M., & Jacoby, L. Depth of processing , recogni- tion, and recall. In J. Brown (Ed

  16. Enabling Healthcare IT Governance: Human Task Management Service for Administering Emergency Department's Resources for Efficient Patient Flow.

    PubMed

    Rodriguez, Salvador; Aziz, Ayesha; Chatwin, Chris

    2014-01-01

    The use of Health Information Technology (HIT) to improve healthcare service delivery is constantly increasing due to research advances in medical science and information systems. Having a fully automated process solution for a Healthcare Organization (HCO) requires a combination of organizational strategies along with a selection of technologies that facilitate the goal of improving clinical outcomes. HCOs, requires dynamic management of care capability to realize the full potential of HIT. Business Process Management (BPM) is being increasingly adopted to streamline the healthcare service delivery and management processes. Emergency Departments (EDs) provide a case in point, which require multidisciplinary resources and services to deliver effective clinical outcomes. Managed care involves the coordination of a range of services in an ED. Although fully automated processes in emergency care provide a cutting edge example of service delivery, there are many situations that require human interactions with the computerized systems; e.g. Medication Approvals, care transfer, acute patient care. This requires a coordination mechanism for all the resources, computer and human, to work side by side to provide the best care. To ensure evidence-based medical practice in ED, we have designed a Human Task Management service to model the process of coordination of ED resources based on the UK's NICE Clinical guideline for managing the care of acutely ill patients. This functionality is implemented using Java Business process Management (jBPM).

  17. Safe Handling of Snakes in an ED Setting.

    PubMed

    Cockrell, Melanie; Swanson, Kristofer; Sanders, April; Prater, Samuel; von Wenckstern, Toni; Mick, JoAnn

    2017-01-01

    Efforts to improve consistency in management of snakes and venomous snake bites in the emergency department (ED) can improve patient and staff safety and outcomes, as well as improve surveillance data accuracy. The emergency department at a large academic medical center identified an opportunity to implement a standardized process for snake disposal and identification to reduce staff risk exposure to snake venom from snakes patients brought with them to the ED. A local snake consultation vendor and zoo Herpetologist assisted with development of a process for snake identification and disposal. All snakes have been identified and securely disposed of using the newly implemented process and no safety incidents have been reported. Other emergency department settings may consider developing a standardized process for snake disposal using listed specialized consultants combined with local resources and suppliers to promote employee and patient safety. Copyright © 2017 Emergency Nurses Association. Published by Elsevier Inc. All rights reserved.

  18. Assessment of the impact of the next generation solvent on DWPF melter off-gas flammability

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Daniel, W. E.

    2013-02-13

    An assessment has been made to evaluate the impact on the DWPF melter off-gas flammability of replacing the current solvent used in the Modular Caustic-Side Solvent Extraction Process Unit (MCU) process with the Next Generation Solvent (NGS-MCU) and blended solvent. The results of this study showed that the concentrations of nonvolatile carbon and hydrogen of the current solvent in the Slurry Mix Evaporator (SME) product would both be about 29% higher than their counterparts of the NGS-MCU and blended solvent in the absence of guanidine partitioning. When 6 ppm of guanidine (TiDG) was added to the effluent transfer to DWPFmore » to simulate partitioning for the NGS-MCU and blended solvent cases and the concentration of Isopar{reg_sign} L in the effluent transfer was controlled below 87 ppm, the concentrations of nonvolatile carbon and hydrogen of the NGS-MCU and blended solvent were still about 12% and 4% lower, respectively, than those of the current solvent. It is, therefore, concluded that as long as the volume of MCU effluent transfer to DWPF is limited to 15,000 gallons per Sludge Receipt and Adjustment Tank (SRAT)/SME cycle and the concentration of Isopar{reg_sign} L in the effluent transfer is controlled below 87 ppm, using the current solvent assumption of 105 ppm Isopar{reg_sign} L or 150 ppm solvent in lieu of NGS-MCU or blended solvent in the DWPF melter off-gas flammability assessment is conservative for up to an additional 6 ppm of TiDG in the effluent due to guanidine partitioning. This report documents the calculations performed to reach this conclusion.« less

  19. [Pediatric anesthesia emergence delirium after elective ambulatory surgery: etiology, risk factors and prevalence].

    PubMed

    Gololobov, Alik; Todris, Liat; Berman, Yakov; Rosenberg-Gilad, Zipi; Schlaeffer, Pnina; Kenett, Ron; Ben-Jacob, Ron; Segal, Eran

    2015-04-01

    Emergence delirium (ED) is a common problem among children and adults recovering from general anesthesia after surgery. Its symptoms include psychomotor agitation, hallucinations, and aggressive behavior. The phenomenon, which is most probably an adverse effect of general anesthesia agents, harms the recovery process and endangers the physical safety of patients and their health. Ranging between 10% and 80%, the exact prevalence of ED is unknown, and the risk factors of the phenomenon are unclear. The aim of the current retrospective study was to determine the prevalence rate of ED in 3947 children recovering from general anesthesia after short elective ambulatory surgery, and to map the influence of various risk factors on this phenomenon. Data were collected using electronic medical records. ED severity was assessed using the Pediatric Anesthesia Emergence Delirium Scale. Results showed the prevalence of ED among children. ED was significantly correlated with patients' age, type of surgery and premedication. ED was not correlated with severity of pain, type of anesthesia or with patients' sex.

  20. The Emergency Department: Challenges and Opportunities for Suicide Prevention.

    PubMed

    Asarnow, Joan Rosenbaum; Babeva, Kalina; Horstmann, Elizabeth

    2017-10-01

    Emergency departments (EDs) can offer life-saving suicide prevention care. This article focuses on the ED and emergency services as service delivery sites for suicide prevention. Characteristics of EDs, models of emergency care, ED screening and brief intervention models, and practice guidelines and parameters are reviewed. A care process model for youths at risk for suicide and self-harm is presented, with guidance for clinicians based on the scientific evidence. Strengthening emergency infrastructure and integrating effective suicide prevention strategies derived from scientific research are critical for advancing suicide prevention objectives. Copyright © 2017 Elsevier Inc. All rights reserved.

  1. Endocrine Disruptors Leading to Obesity and Related Diseases.

    PubMed

    Petrakis, Demetrios; Vassilopoulou, Loukia; Mamoulakis, Charalampos; Psycharakis, Christos; Anifantaki, Aliki; Sifakis, Stavros; Docea, Anca Oana; Tsiaoussis, John; Makrigiannakis, Antonios; Tsatsakis, Aristides M

    2017-10-24

    The review aims to comprehensively present the impact of exposure to endocrine disruptors (EDs) in relation to the clinical manifestation of obesity and related diseases, including diabetes mellitus, metabolic syndrome, cardiovascular diseases, carcinogenesis and infertility. EDs are strong participants in the obesity epidemic scenery by interfering with cellular morphological and biochemical processes; by inducing inflammatory responses; and by presenting transcriptional and oncogenic activity. Obesity and lipotoxicity enhancement occur through reprogramming and/or remodeling of germline epigenome by exposure to EDs. Specific population groups are vulnerable to ED exposure due to current dietary and environmental conditions. Obesity, morbidity and carcinogenicity induced by ED exposure are an evolving reality. Therefore, a new collective strategic approach is deemed essential, for the reappraisal of current global conditions pertaining to energy management.

  2. Modeling solvent evaporation during thin film formation in phase separating polymer mixtures

    DOE PAGES

    Cummings, John; Lowengrub, John S.; Sumpter, Bobby G.; ...

    2018-02-09

    Preparation of thin films by dissolving polymers in a common solvent followed by evaporation of the solvent has become a routine processing procedure. However, modeling of thin film formation in an evaporating solvent has been challenging due to a need to simulate processes at multiple length and time scales. In this paper, we present a methodology based on the principles of linear non-equilibrium thermodynamics, which allows systematic study of various effects such as the changes in the solvent properties due to phase transformation from liquid to vapor and polymer thermodynamics resulting from such solvent transformations. The methodology allows for themore » derivation of evaporative flux and boundary conditions near each surface for simulations of systems close to the equilibrium. We apply it to study thin film microstructural evolution in phase segregating polymer blends dissolved in a common volatile solvent and deposited on a planar substrate. Finally, effects of the evaporation rates, interactions of the polymers with the underlying substrate and concentration dependent mobilities on the kinetics of thin film formation are studied.« less

  3. Modeling solvent evaporation during thin film formation in phase separating polymer mixtures

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Cummings, John; Lowengrub, John S.; Sumpter, Bobby G.

    Preparation of thin films by dissolving polymers in a common solvent followed by evaporation of the solvent has become a routine processing procedure. However, modeling of thin film formation in an evaporating solvent has been challenging due to a need to simulate processes at multiple length and time scales. In this paper, we present a methodology based on the principles of linear non-equilibrium thermodynamics, which allows systematic study of various effects such as the changes in the solvent properties due to phase transformation from liquid to vapor and polymer thermodynamics resulting from such solvent transformations. The methodology allows for themore » derivation of evaporative flux and boundary conditions near each surface for simulations of systems close to the equilibrium. We apply it to study thin film microstructural evolution in phase segregating polymer blends dissolved in a common volatile solvent and deposited on a planar substrate. Finally, effects of the evaporation rates, interactions of the polymers with the underlying substrate and concentration dependent mobilities on the kinetics of thin film formation are studied.« less

  4. A collaborative quality improvement model and electronic community of practice to support sepsis management in emergency departments: investigating care harmonization for provincial knowledge translation.

    PubMed

    Ho, Kendall; Marsden, Julian; Jarvis-Selinger, Sandra; Novak Lauscher, Helen; Kamal, Noreen; Stenstrom, Rob; Sweet, David; Goldman, Ran D; Innes, Grant

    2012-07-12

    Emergency medicine departments within several organizations are now advocating the adoption of early intervention guidelines for patients with the signs and symptoms of sepsis. This proposed research will lead to a comprehensive understanding of how diverse emergency department (ED) sites across British Columbia (BC), Canada, engage in a quality improvement collaborative to lead to improvements in time-based process measures and clinical outcomes for septic patients in EDs. To address the challenge of sepsis management, in 2007, the BC Ministry of Health began working with emergency health professionals, including health administrators, to establish a provincial ED collaborative: Evidence to Excellence (E2E). The E2E initiative employs the Institute for Healthcare Improvement (IHI) model and is supported by a Web-based community of practice (CoP) in emergency medicine. It aims to (1) support clinicians in accessing and applying evidence to clinical practice in emergency medicine, (2) support system change and clinical process improvement, and (3) develop resources and strategies to facilitate knowledge translation and process improvement. Improving sepsis management is one of the central foci of the E2E initiative. The primary purpose of our research is to investigate whether the application of sepsis management protocols leads to improved time-based process measures and clinical outcomes for patients presenting to EDs with sepsis. Also, we seek to investigate the implementation of sepsis protocols among different EDs. For example: (1) How can sepsis protocols be harmonized among different EDs? (2) What are health professionals' perspectives on interprofessional collaboration with various EDs? and (3) What are the factors affecting the level of success among EDs? Lastly, working in collaboration with the BC Ministry of Health as our policy-maker partner, the research will investigate how the demonstrated efficacy of this research can be applied on a provincial and national level to establish a template for policy makers from other jurisdictions to translate knowledge into action for EDs. This research study will employ the IHI model for improvement, incorporate the principles of participatory action research, and use the E2E online CoP to engage ED practitioners (eg, physicians, nurses, and administrators, exchanging ideas, engaging in discussions, sharing resources, and amalgamating knowledge) from across BC to (1) share the evidence of early intervention in sepsis, (2) adapt the evidence to their patterns of practice, (3) develop a common set of orders for implementing the sepsis pathway, and (4) agree on common indicators to measure clinical outcomes. Our hypothesis is that combining the social networking ability of an electronic CoP and its inherent knowledge translation capacity with the structured project management of the IHI model will result in widespread and sustained improvement in the emergency and overall care of patients with severe sepsis presenting to EDs throughout BC.

  5. DEMONSTRATION BULLETIN: TERRA KLEEN SOLVENT EXTRACTION TECHNOLOGY - TERRA-KLEEN RESPONSE GROUP, INC.

    EPA Science Inventory

    The Terra-Kleen Solvent Extraction Technology was developed by Terra-Kleen Response Group, Inc., to remove polychlorinated biphenyls (PCB) and other organic constituents from contaminated soil. This batch process system uses a proprietary solvent at ambient temperatures to treat ...

  6. Interactions between Biological and Abiotic Pathways in the Reduction of Chlorinated Solvents

    EPA Science Inventory

    While biologically mediated reductive dechlorination continues to be a significant focus of chlorinated solvent remediation, there has been an increased interest in abiotic reductive processes for the remediation of chlorinated solvents. In situ chemical reduction (ISCR) uses zer...

  7. Building a Natural Language Processing Tool to Identify Patients With High Clinical Suspicion for Kawasaki Disease from Emergency Department Notes.

    PubMed

    Doan, Son; Maehara, Cleo K; Chaparro, Juan D; Lu, Sisi; Liu, Ruiling; Graham, Amanda; Berry, Erika; Hsu, Chun-Nan; Kanegaye, John T; Lloyd, David D; Ohno-Machado, Lucila; Burns, Jane C; Tremoulet, Adriana H

    2016-05-01

    Delayed diagnosis of Kawasaki disease (KD) may lead to serious cardiac complications. We sought to create and test the performance of a natural language processing (NLP) tool, the KD-NLP, in the identification of emergency department (ED) patients for whom the diagnosis of KD should be considered. We developed an NLP tool that recognizes the KD diagnostic criteria based on standard clinical terms and medical word usage using 22 pediatric ED notes augmented by Unified Medical Language System vocabulary. With high suspicion for KD defined as fever and three or more KD clinical signs, KD-NLP was applied to 253 ED notes from children ultimately diagnosed with either KD or another febrile illness. We evaluated KD-NLP performance against ED notes manually reviewed by clinicians and compared the results to a simple keyword search. KD-NLP identified high-suspicion patients with a sensitivity of 93.6% and specificity of 77.5% compared to notes manually reviewed by clinicians. The tool outperformed a simple keyword search (sensitivity = 41.0%; specificity = 76.3%). KD-NLP showed comparable performance to clinician manual chart review for identification of pediatric ED patients with a high suspicion for KD. This tool could be incorporated into the ED electronic health record system to alert providers to consider the diagnosis of KD. KD-NLP could serve as a model for decision support for other conditions in the ED. © 2016 by the Society for Academic Emergency Medicine.

  8. Integrated care in the emergency department: a complex adaptive systems perspective.

    PubMed

    Nugus, Peter; Carroll, Katherine; Hewett, David G; Short, Alison; Forero, Roberto; Braithwaite, Jeffrey

    2010-12-01

    Emergency clinicians undertake boundary-work as they facilitate patient trajectories through the Emergency Department (ED). Emergency clinicians must manage the constantly-changing dynamics at the boundaries of the ED and other hospital departments and organizations whose services emergency clinicians seek to integrate. Integrating the care that differing clinical groups provide, the services EDs offer, and patients' needs across this journey is challenging. The journey is usually accounted for in a linear way - as a "continuity of care" problem. In this paper, we instead conceptualize integrated care in the ED using a complex adaptive systems (CAS) perspective. A CAS perspective accounts for the degree to which other departments and units outside of the ED are integrated, and appropriately described, using CAS concepts and language. One year of ethnographic research was conducted, combining observation and semi-structured interviews, in the EDs of two tertiary referral hospitals in Sydney, Australia. We found the CAS approach to be salient to analyzing integrated care in the ED because the processes of categorization, diagnosis and discharge are primarily about the linkages between services, and the communication and negotiation required to enact those linkages, however imperfectly they occur in practice. Emergency clinicians rapidly process large numbers of high-need patients, in a relatively efficient system of care inadequately explained by linear models. A CAS perspective exposes integrated care as management of the patient trajectory within porous, shifting and negotiable boundaries. Copyright © 2010 Elsevier Ltd. All rights reserved.

  9. Deactivation of 6-Aminocoumarin Intramolecular Charge Transfer Excited State through Hydrogen Bonding

    PubMed Central

    Krystkowiak, Ewa; Dobek, Krzysztof; Maciejewski, Andrzej

    2014-01-01

    This paper presents results of the spectral (absorption and emission) and photophysical study of 6-aminocoumarin (6AC) in various aprotic hydrogen-bond forming solvents. It was established that solvent polarity as well as hydrogen-bonding ability influence solute properties. The hydrogen-bonding interactions between S1-electronic excited solute and solvent molecules were found to facilitate the nonradiative deactivation processes. The energy-gap dependence on radiationless deactivation in aprotic solvents was found to be similar to that in protic solvents. PMID:25244014

  10. Process analysis and modeling of a single-step lutein extraction method for wet microalgae.

    PubMed

    Gong, Mengyue; Wang, Yuruihan; Bassi, Amarjeet

    2017-11-01

    Lutein is a commercial carotenoid with potential health benefits. Microalgae are alternative sources for the lutein production in comparison to conventional approaches using marigold flowers. In this study, a process analysis of a single-step simultaneous extraction, saponification, and primary purification process for free lutein production from wet microalgae biomass was carried out. The feasibility of binary solvent mixtures for wet biomass extraction was successfully demonstrated, and the extraction kinetics of lutein from chloroplast in microalgae were first evaluated. The effects of types of organic solvent, solvent polarity, cell disruption method, and alkali and solvent usage on lutein yields were examined. A mathematical model based on Fick's second law of diffusion was applied to model the experimental data. The mass transfer coefficients were used to estimate the extraction rates. The extraction rate was found more significantly related with alkali ratio to solvent than to biomass. The best conditions for extraction efficiency were found to be pre-treatment with ultrasonication at 0.5 s working cycle per second, react 0.5 h in 0.27 L/g solvent to biomass ratio, and 1:3 ether/ethanol (v/v) with 1.25 g KOH/L. The entire process can be controlled within 1 h and yield over 8 mg/g lutein, which is more economical for scale-up.

  11. EXXON donor solvent coal liquefaction process

    NASA Technical Reports Server (NTRS)

    Epperly, W. R.; Swabb, L. E., Jr.; Tauton, J. W.

    1978-01-01

    A solvent coal liquefaction process to produce low-sulfur liquid products from a wide range of coals is described. An integrated program of laboratory and engineering research and development in conjunction with operation of a 250 T/D pilot plant is discussed.

  12. The quality assurance program of organ donation in Tuscany.

    PubMed

    Bozzi, G; Saviozzi, A; De Simone, P; Filipponi, F

    2008-01-01

    Constant monitoring is paramount in order to detect the criticalities and improve the results of the deceased donation process. Concomitant with the institution of a regional transplantation service authority--Organizzazione Toscana Trapianti--in 2003, Tuscany adopted a program of quality assurance of the deceased donation process by compulsory reporting of all encephalic deaths from local intensive care units to the regional transplant office in Florence. The indicators we adopted were the efficiency of deceased donor (DD) identification, expressed as the ratio of encephalic deaths (ED) to total deaths with encephalic lesions (EL) (ie, ED/EL); the efficiency of DD reporting, expressed as the ratio of reported potential DD (RPDD) to total ED (ie, RPDD/ED); the efficacy of the DD process, as the ratio between actual DD (ADD) to total ED (ie, ADD/ED); the conversion rate; the percent of opposition to donation; and the incidence of DD maintenance failures. Data were collected prospectively, stratified by regional hospital consortia (Aziende Sanitarie Locali) and compared with international benchmarks. In the period 2003-2006 the mean efficiency of DD identification was 48.3%+/-4.4% (range 42.6%-53.2%); the mean efficiency of DD reporting was 95.2%+/-2.5% (range 92.5%-98.5%); the mean efficacy of the deceased donation process was 51.8%+/-2.4% (range 48.6%-54.4%); the mean conversion rate was 59.6%+/-2.2% (range 57.6%-62.7%); the mean opposition rate was 31.9%+/-1.1% (range 30.6%-33.2%); and the incidence of DD maintenance failure was 5%+/-2.9% (range 2.2%-8.7%). The breakdown analysis revealed wide interhospital variability in terms of efficiency of DD identification (from a low of 25% to a high of 80%); efficacy of the donation process (from a low of 22% to a high of 79%); and conversion rate (from a low of 29% to a high of 79%). Our results highlight that the donation process gets started in about 50% of eligible cases. Further strategies are favored to address this critical area.

  13. Bench Scale Process for Low Cost CO 2 Capture Using a PhaseChanging Absorbent: Techno-Economic Analysis Topical Report

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Miebach, Barbara; McDuffie, Dwayne; Spiry, Irina

    The objective of this project is to design and build a bench-scale process for a novel phase-changing CO 2 capture solvent. The project will establish scalability and technical and economic feasibility of using a phase-changing CO 2 capture absorbent for post-combustion capture of CO 2 from coal-fired power plants with 90% capture efficiency and 95% CO 2 purity at a cost of $40/tonne of CO 2 captured by 2025 and a cost of <$10/tonne of CO 2 captured by 2035. This report presents system and economic analysis for a process that uses a phase changing aminosilicone solvent to remove COmore » 2 from pulverized coal (PC) power plant flue gas. The aminosilicone solvent is a pure 1,3-bis(3-aminopropyl)-1,1,3,3-tetramethyldisiloxane (GAP-0). Performance of the phase-changing aminosilicone technology is compared to that of a conventional carbon capture system using aqueous monoethanolamine (MEA). This analysis demonstrates that the aminosilicone process has significant advantages relative to an MEA-based system. The first-year CO 2 removal cost for the phase-changing CO 2 capture process is $52.1/tonne, compared to $66.4/tonne for the aqueous amine process. The phase-changing CO 2 capture process is less costly than MEA because of advantageous solvent properties that include higher working capacity, lower corrosivity, lower vapor pressure, and lower heat capacity. The phase-changing aminosilicone process has approximately 32% lower equipment capital cost compared to that of the aqueous amine process. However, this solvent is susceptible to thermal degradation at CSTR desorber operating temperatures, which could add as much as $88/tonne to the CO 2 capture cost associated with solvent makeup. Future work is focused on mitigating this critical risk by developing an advanced low-temperature desorber that can deliver comparable desorption performance and significantly reduced thermal degradation rate.« less

  14. Nonadiabatic ab initio molecular dynamics with PME-ONIOM scheme of photoisomerization reaction between 1,3-cyclohexadiene and 1,3,5-cis-hexatriene in solution phase

    NASA Astrophysics Data System (ADS)

    Ohta, Ayumi; Kobayashi, Osamu; Danielache, Sebastian O.; Nanbu, Shinkoh

    2017-03-01

    The ultra-fast photoisomerization reactions between 1,3-cyclohexadiene (CHD) and 1,3,5-cis-hexatriene (HT) in both hexane and ethanol solvents were revealed by nonadiabatic ab initio molecular dynamics (AI-MD) with a particle-mesh Ewald summation method and our Own N-layered Integrated molecular Orbital and molecular Mechanics model (PME-ONIOM) scheme. Zhu-Nakamura version trajectory surface hopping method (ZN-TSH) was employed to treat the ultra-fast nonadiabatic decaying process. The results for hexane and ethanol simulations reasonably agree with experimental data. The high nonpolar-nonpolar affinity between CHD and the solvent was observed in hexane solvent, which definitely affected the excited state lifetimes, the product branching ratio of CHD:HT, and solute (CHD) dynamics. In ethanol solvent, however, the CHD solute was isomerized in the solvent cage caused by the first solvation shell. The photochemical dynamics in ethanol solvent results in the similar property to the process appeared in vacuo (isolated CHD dynamics).

  15. Green Aspects of Techniques for the Determination of Currently Used Pesticides in Environmental Samples

    PubMed Central

    Stocka, Jolanta; Tankiewicz, Maciej; Biziuk, Marek; Namieśnik, Jacek

    2011-01-01

    Pesticides are among the most dangerous environmental pollutants because of their stability, mobility and long-term effects on living organisms. Their presence in the environment is a particular danger. It is therefore crucial to monitor pesticide residues using all available analytical methods. The analysis of environmental samples for the presence of pesticides is very difficult: the processes involved in sample preparation are labor-intensive and time-consuming. To date, it has been standard practice to use large quantities of organic solvents in the sample preparation process; but as these solvents are themselves hazardous, solvent-less and solvent-minimized techniques are becoming popular. The application of Green Chemistry principles to sample preparation is primarily leading to the miniaturization of procedures and the use of solvent-less techniques, and these are discussed in the paper. PMID:22174632

  16. Method for improving dissolution efficiency in gas-absorption and liquid extraction processes. [Patent application

    DOEpatents

    Kanak, B.E.; Stephenson, M.J.

    1980-01-11

    A method is described for improving dissolution efficiency in processes in which a feed fluid is introduced to a zone where it is contacted with a liquid solvent for preferentially removing a component of the feed and where part of the solvent so contacted undergoes transfer into the feed fluid to saturate the same. It has been found that such transfer significantly impairs dissolution efficiency. In accordance with the invention, an amount of the above-mentioned solvent is added to the feed fluid being introduced to the contact zone, the solvent being added in an amount sufficient to effect reduction or elimination of the above-mentioned transfer. Preferably, the solvent is added to the feed fluid in an amount saturating or supersaturating the feed fluid under the conditions prevailing in the contact zone.

  17. Method for improving dissolution efficiency in gas-absorption and liquid extraction processes

    DOEpatents

    Kanak, Brant E.; Stephenson, Michael J.

    1981-01-01

    This invention is a method for improving dissolution efficiency in processes in which a feed fluid is introduced to a zone where it is contacted with a liquid solvent for preferentially removing a component of the feed and where part of the solvent so contacted undergoes transfer into the feed fluid to saturate the same. It has been found that such transfer significantly impairs dissolution efficiency. In accordance with the invention, an amount of the above-mentioned solvent is added to the feed fluid being introduced to the contact zone, the solvent being added in an amount sufficient to effect reduction or elimination of the above-mentioned transfer. Preferably, the solvent is added to the feed fluid in an amount saturating or supersaturating the feed fluid under the conditions prevailing in the contact zone.

  18. Low-Temperature, Solution-Processed, Transparent Zinc Oxide-Based Thin-Film Transistors for Sensing Various Solvents

    PubMed Central

    You, Hsin-Chiang; Wang, Cheng-Jyun

    2017-01-01

    A low temperature solution-processed thin-film transistor (TFT) using zinc oxide (ZnO) film as an exposed sensing semiconductor channel was fabricated to detect and identify various solution solvents. The TFT devices would offer applications for low-cost, rapid and highly compatible water-soluble detection and could replace conventional silicon field effect transistors (FETs) as bio-sensors. In this work, we demonstrate the utility of the TFT ZnO channel to sense various liquids, such as polar solvents (ethanol), non-polar solvents (toluene) and deionized (DI) water, which were dropped and adsorbed onto the channel. It is discussed how different dielectric constants of polar/non-polar solvents and DI water were associated with various charge transport properties, demonstrating the main detection mechanisms of the thin-film transistor. PMID:28772592

  19. Synthesis, fractionation, and thin film processing of nanoparticles using the tunable solvent properties of carbon dioxide gas expanded liquids

    NASA Astrophysics Data System (ADS)

    Anand, Madhu

    Nanoparticles have received significant attention because of their unusual characteristics including high surface area to volume ratios. Materials built from nanoparticles possess unique chemical, physical, mechanical and optical properties. Due to these properties, they hold potential in application areas such as catalysts, sensors, semiconductors and optics. At the same time, CO 2 in the form of supercritical fluid or CO2 gas-expanded liquid mixtures has gained significant attention in the area of processing nanostructures. This dissertation focuses on the synthesis and processing of nanoparticles using CO2 tunable solvent systems. Nanoparticle properties depend heavily on their size and, as such, the ability to finely control the size and uniformity of nanoparticles is of utmost importance. Solution based nanoparticle formation techniques are attractive due to their simplicity, but they often result in the synthesis of particles with a wide size range. To address this limitation, a post-synthesis technique has been developed in this dissertation to fractionate polydisperse nanoparticles ( s . = 30%) into monodisperse fractions ( s . = 8%) using tunable physicochemical properties of CO 2 expanded liquids, where CO2 is employed as an antisolvent. This work demonstrates that by controlling the addition of CO2 (pressurization) to an organic dispersion of nanoparticles, the ligand stabilized nanoparticles can be size selectively precipitated within a novel high pressure apparatus that confines the particle precipitation to a specified location on a surface. Unlike current techniques, this CO2 expanded liquid approach provides faster and more efficient particle size separation, reduction in organic solvent usage, and pressure tunable size selection in a single process. To improve our fundamental understanding and to further refine the size separation process, a detailed study has been performed to identify the key parameters enabling size separation of various nanoparticle populations. This study details the influence of various factors on the size separation process, such as the types of nanoparticles, ligand type and solvent type as well as the use of recursive fractionation and the time allowed for settling during each fractionation step. This size selective precipitation technique was also applied to fractionate and separate polydisperse dispersions of CdSe/ZnS semiconductor nanocrystals into very distinct size and color fractions based solely on the pressure tunable solvent properties of CO2 expanded liquids. This size selective precipitation of nanoparticles is achieved by finely tuning the solvent strength of the CO2/organic solvent medium by simply adjusting the applied CO2 pressure. These subtle changes affect the balance between osmotic repulsive and van der Waals attractive forces thereby allowing fractionation of the nanocrystals into multiple narrow size populations. Thermodynamic analysis of nanoparticle size selective fractionation was performed to develop a theoretical model based on the thermodynamic properties of gas expanded liquids. We have used the general phenomenon of nanoparticle precipitation with CO2 expanded liquids to create dodecanethiol stabilized gold nanoparticle thin films. This method utilizes CO2 as an anti-solvent for low defect, wide area gold nanoparticle film formation employing monodisperse gold nanoparticles. Dodecanethiol stabilized gold particles are precipitated from hexane by controllably expanding the solution with carbon dioxide. Subsequent addition of carbon dioxide as a dense supercritical fluid then provides for removal of the organic solvent while avoiding the dewetting effects common to evaporating solvents. Unfortunately, the use of carbon dioxide as a neat solvent in nanoparticles synthesis and processing is limited by the very poor solvent strength of dense phase CO2. As a result, most current techniques employed to synthesize and disperse nanoparticles in neat carbon dioxide require the use of environmentally persistent fluorinated compounds as metal precursors and/or stabilizing ligands. This dissertation presents the first report of the simultaneous synthesis and stabilization of metallic nanoparticles in carbon dioxide solvent without the use of any fluorinated compounds thereby further enabling the use of CO 2 as a green solvent medium in nanomaterials synthesis and processing.

  20. Effect of a redesigned fracture management pathway and 'virtual' fracture clinic on ED performance.

    PubMed

    Vardy, J; Jenkins, P J; Clark, K; Chekroud, M; Begbie, K; Anthony, I; Rymaszewski, L A; Ireland, A J

    2014-06-13

    Collaboration between the orthopaedic and emergency medicine (ED) services has resulted in standardised treatment pathways, leaflet supported discharge and a virtual fracture clinic review. Patients with minor, stable fractures are discharged with no further follow-up arranged. We aimed to examine the time taken to assess and treat these patients in the ED along with the rate of unplanned reattendance. A retrospective study was undertaken that covered 1 year before the change and 1 year after. Prospectively collected administrative data from the electronic patient record system were analysed and compared before and after the change. An ED and orthopaedic unit, serving a population of 300 000, in a publicly funded health system. 2840 patients treated with referral to a traditional fracture clinic and 3374 patients managed according to the newly redesigned protocol. Time for assessment and treatment of patients with orthopaedic injuries not requiring immediate operative management, and 7-day unplanned reattendance. Where plaster backslabs were replaced with removable splints, the consultation time was reduced. There was no change in treatment time for other injuries treated by the new discharge protocol. There was no increase in unplanned ED attendance, related to the injury, within 7 days (p=0.149). There was a decrease in patients reattending the ED due to a missed fracture clinic appointment. This process did not require any new time resources from the ED staff. This process brought significant benefits to the ED as treatment pathways were agreed. The pathway reduced unnecessary reattendance of patients at face-to-face fracture clinics for a review of stable, self-limiting injuries. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

  1. Nurses take ownership of rads discrepancies.

    PubMed

    2010-02-01

    The ED at Catawba Valley Medical Center in Hickory, NC, has improved its responses to radiology discrepancies by redesigning its process and giving ownership of that process to two nurses. Here are some of the key aspects of the process: every day the coordinators check the computer system, into which discrepancies are entered by radiology. Diagnosis and treatment are reviewed with one of the ED physicians. If the patient has been discharged, the coordinator will contact the patient via phone or follow-up letter.

  2. Event-Driven Technology to Generate Relevant Collections of Near-Realtime Data

    NASA Astrophysics Data System (ADS)

    Graves, S. J.; Keiser, K.; Nair, U. S.; Beck, J. M.; Ebersole, S.

    2017-12-01

    Getting the right data when it is needed continues to be a challenge for researchers and decision makers. Event-Driven Data Delivery (ED3), funded by the NASA Applied Science program, is a technology that allows researchers and decision makers to pre-plan what data, information and processes they need to have collected or executed in response to future events. The Information Technology and Systems Center at the University of Alabama in Huntsville (UAH) has developed the ED3 framework in collaboration with atmospheric scientists at UAH, scientists at the Geological Survey of Alabama, and other federal, state and local stakeholders to meet the data preparedness needs for research, decisions and situational awareness. The ED3 framework supports an API that supports the addition of loosely-coupled, distributed event handlers and data processes. This approach allows the easy addition of new events and data processes so the system can scale to support virtually any type of event or data process. Using ED3's underlying services, applications have been developed that monitor for alerts of registered event types and automatically triggers subscriptions that match new events, providing users with a living "album" of results that can continued to be curated as more information for an event becomes available. This capability can allow users to improve capacity for the collection, creation and use of data and real-time processes (data access, model execution, product generation, sensor tasking, social media filtering, etc), in response to disaster (and other) events by preparing in advance for data and information needs for future events. This presentation will provide an update on the ED3 developments and deployments, and further explain the applicability for utilizing near-realtime data in hazards research, response and situational awareness.

  3. Impact of process improvements on measures of emergency department efficiency.

    PubMed

    Leung, Alexander K; Whatley, Shawn D; Gao, Dechang; Duic, Marko

    2017-03-01

    To study the operational impact of process improvements on emergency department (ED) patient flow. The changes did not require any increase in resources or expenditures. This was a 36-month pre- and post-intervention study to evaluate the effect of implementing process improvements at a community ED from January 2010 to December 2012. The intervention comprised streamlining triage by having patients accepted into internal waiting areas immediately after triage. Within the ED, parallel processes unfolded, and there was no restriction on when registration occurred or which health care provider a patient saw first. Flexible nursing ratios allowed nursing staff to redeploy and move to areas of highest demand. Last, demand-based physician scheduling was implemented. The main outcome was length of stay (LOS). Secondary outcomes included time to physician initial assessment (PIA), left-without-being-seen (LWBS) rates, and left-against-medical-advice (LAMA) rates. Segmented regression of interrupted time series analysis was performed to quantify the impact of the intervention, and whether it was sustained. Patients totalling 251,899 attended the ED during the study period. Daily patient volumes increased 17.3% during the post-intervention period. Post-intervention, mean LOS decreased by 0.64 hours (p<0.005). LOS for non-admitted Canadian Triage and Acuity Scale 2 (-0.58 hours, p<0.005), 3 (-0.75 hours, p<0.005), and 4 (-0.32 hours, p<0.005) patients also decreased. There were reductions in PIA (43.81 minutes, p<0.005), LWBS (35.2%, p<0.005), and LAMA (61.9%, p<0.005). A combination of process improvements in the ED was associated with clinically significant reductions in LOS, PIA, LWBS, and LAMA for non-resuscitative patients.

  4. SOLVENT EXTRACTION PROCESSES: A SURVEY OF SYSTEMS IN THE SITE PROGRAM

    EPA Science Inventory

    Solvent extraction of contaminated soils, sludges and sediments has been successfully completed at a number ofSuperfund sites. Each commercialized process uses a unique operating system to extract organic contaminants from solids. These operating systems may be classified by the ...

  5. Pervaporation and Vapor Permeation Tutorial: Membrane Processes for the Selective Separation of Liquid and Vapor Mixtures

    EPA Science Inventory

    Pervaporation and vapor permeation are membrane-based processes proposed as alternatives to conventional separation technologies. Applications range from organic solvent removal from water, ethanol or butanol recovery from fermentation broths, solvent/biofuel dehydration to meet ...

  6. Pervaporation & Vapor Permeation Membrane Processes for the Selective Separation of Liquid and Vapor Mixtures

    EPA Science Inventory

    Pervaporation and vapor permeation are membrane-based processes which have been proposed as alternatives to conventional separation technologies. Applications range from organic solvent removal from water, ethanol or butanol recovery from dilute fermentation broths, solvent/biofu...

  7. ED becomes 'lean' and cuts LBTC, LOS times.

    PubMed

    2008-04-01

    Lean manufacturing techniques, first developed by Toyota, can be successfully adapted to help improve processes in your ED. St. Luke's Episcopal Hospital in Houston, has used Lean to reduce median length of stay, frequency of diversions, and the percentage of patients who left before treatment was complete (LBTC). Here's why "Lean" can help improve the performance of your ED: It enables you and your staff to see things from the patient's point of view. Lean tools enable you to view the status of your department in real-time and to compare that status with your performance goals. Exercises help identify areas where your processes break down and determine the most likely solutions.

  8. Solvent dependence of the activation energy of attachment determined by single molecule observations of surfactant adsorption.

    PubMed

    Honciuc, Andrei; Baptiste, Denver Jn; Campbell, Ian P; Schwartz, Daniel K

    2009-07-07

    Single-molecule total internal reflection fluorescence microscopy was used to obtain real-time images of fluorescently labeled hexadecanoic (palmitic) acid molecules as they adsorbed at the interface between fused silica and three different solvents: hexadecane (HD), tetrahydrofuran (THF), and water. These solvents were chosen to explore the effect of solvent polarity on the activation energy associated with the attachment rate, i.e., the rate at which molecules were transferred to the surface from the near-surface layer. Direct counting of single-molecule events, made under steady-state conditions at extremely low coverage, provided direct, model-independent measurements of this attachment rate, in contrast with conventional ensemble-averaged methods, which are influenced by bulk transport and competing detachment processes. We found that the attachment rate increased with increasing temperature for all solvents. Arrhenius analyses gave activation energies of 5+/-2 kJ/mol for adsorption from HD, 10+/-2 kJ/mol for adsorption from THF, and 19+/-2 kJ/mol for adsorption from water. These energies increased systematically with the solvent polarity and, therefore, with the expected strength of the solvent-substrate interaction. We hypothesize that the adsorption of amphiphilic solute molecules from solution can be regarded as a competitive exchange between solute molecules and surface-bound solvent. In this scenario, adsorption is an activated process, and the activation energy for attachment is associated with the solvent-substrate interaction energy.

  9. Development of key performance indicators for emergency departments in Ireland using an electronic modified-Delphi consensus approach.

    PubMed

    Wakai, Abel; O'Sullivan, Ronan; Staunton, Paul; Walsh, Cathal; Hickey, Fergal; Plunkett, Patrick K

    2013-04-01

    The objective of this study was to develop a consensus among emergency medicine (EM) specialists working in Ireland for emergency department (ED) key performance indicators (KPIs). The method employed was a three-round electronic modified-Delphi process. An online questionnaire with 54 potential KPIs was set up for round 1 of the Delphi process. The Delphi panel consisted of all registered EM specialists in Ireland. Each indicator on the questionnaire was rated using a five-point Likert-type rating scale. Agreement was defined as at least 70% of the responders rating an indicator as 'agree' or 'strongly agree' on the rating scale. Data were analysed using standard descriptive statistics. Data were also analysed as the mean of the Likert rating with 95% confidence intervals (95% CIs). Sensitivity of the ratings was examined for robustness by bootstrapping the original sample. Statistical analyses were carried out using SPSS version 16.0. The response rates in rounds 1, 2 and 3 were 86, 88 and 88%, respectively. Ninety-seven potential indicators reached agreement after the three rounds. In the context of the Donabedian structure-process-outcome framework of performance indicators, 41 (42%) of the agreed indicators were structure indicators, 52 (54%) were process indicators and four (4%) were outcome indicators. Overall, the top-three highest rated indicators were: presence of a dedicated ED clinical information system (4.7; 95% CI 4.6-4.9), ED compliance with minimum design standards (4.7; 95% CI 4.5-4.8) and time from ED arrival to first ECG in suspected cardiac chest pain (4.7; 95% CI 4.5-4.9). The top-three highest rated indicators specific to clinical care of children in EDs were: time to administration of antibiotics in children with suspected bacterial meningitis (4.6; 95% CI 4.5-4.8), separate area available within EDs (seeing both adults and children) to assess children (4.4; 95% CI 4.2-4.6) and time to administration of analgesia in children with forearm fractures (4.4; 95% CI 4.2-4.7). Employing a Delphi consensus process, it was possible to reach a consensus among EM specialists in Ireland on a suite of 97 KPIs for EDs.

  10. In-situ XRD and EDS method study on the oxidation behaviour of Ni-Cu sulphide ore.

    PubMed

    Li, Guangshi; Cheng, Hongwei; Xiong, Xiaolu; Lu, Xionggang; Xu, Cong; Lu, Changyuan; Zou, Xingli; Xu, Qian

    2017-06-12

    The oxidation mechanism of sulfides is the key issue during the sulphide-metallurgy process. In this study, the phase transformation and element migration were clearly demonstrated by in-situ laboratory-based X-ray diffraction (XRD) and energy-dispersive X-ray spectroscopy (EDS), respectively. The reaction sequence and a four-step oxidation mechanism were proposed and identified. The elemental distribution demonstrated that at a low temperature, the Fe atoms diffused outward and the Ni/Cu atoms migrated toward the inner core, whereas the opposite diffusion processes were observed at a higher temperature. Importantly, the unique visual presentation of the oxidation behaviour provided by the combination of in-situ XRD and EDS might be useful for optimising the process parameters to improve the Ni/Cu extraction efficiency during Ni-Cu sulphide metallurgy.

  11. The Market Responses to the Government Regulation of Chlorinated Solvents: A Policy Analysis

    DTIC Science & Technology

    1988-10-01

    in the process of statistical estimation of model parameters. The results of the estimation process applied to chlorinated solvent markets show the...93 C.5. Marginal Feedstock Cost Series Estimates for Process Share of Total Production .................................. 94 F.I...poliay context for this research. Section III provides analysis necessary to understand the chemicals involved, their production processes and costs, and

  12. REMEDIATING PESTICIDE CONTAMINATED SOILS USING SOLVENT EXTRACTION

    EPA Science Inventory

    Bench-scale solvent extraction studies were performed on soil samples obtained from a Superfund site contaminated with high levels of p,p'-DDT, p,p'-DDD,, p,p'-DDE and toxaphene. The effectiveness of the solvent extraction process was assessed using methanol and 2-propanol as sol...

  13. Fluoro-alcohol phase modifiers and process for cesium solvent extraction

    DOEpatents

    Bonnesen, Peter V.; Moyer, Bruce A.; Sachleben, Richard A.

    2003-05-20

    The invention relates to a class of phenoxy fluoro-alcohols, their preparation, and their use as phase modifiers and solvating agents in a solvent composition for the extraction of cesium from alkaline solutions. These phenoxy fluoro-alcohols comply with the formula: ##STR1## in which n=2 to 4; X represents a hydrogen or a fluorine atom, and R.sup.2 -R.sup.6 are hydrogen or alkyl substituents. These phenoxy fluoro-alcohol phase modifiers are a necessary component to a robust solvent composition and process useful for the removal of radioactive cesium from alkaline nuclear waste streams. The fluoro-alcohols can also be used in solvents designed to extract other cesium from acidic or neutral solutions.

  14. Pilot-Scale Silicone Process for Low-Cost Carbon Dioxide Capture. Final Scientific/Technical Report

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Hancu, Dan; Wood, Benjamin; Genovese, Sarah

    GE Global Research has developed, over the last 8 years, a platform of cost effective CO 2 capture technologies based on a non-aqueous aminosilicone solvent (GAP-1m). As demonstrated in a previous funded DOE project (DE-FE0007502), the GAP-1m solvent has increased CO 2 working capacity, lower volatility and corrosivity than the benchmark aqueous amine technology. The current report describes the cooperative program between GE Global Research (GE GRC), and the National Carbon Capture Center (NCCC) to design, construct, and operate a pilot-scale process using GAP-1m solvent to demonstrate its performance at 0.5 MWe. (i) Performance of the GAP-1m solvent was demonstratedmore » in a 0.5 MWe pilot with real flue gas for over 900 hrs. of operation using two alternative desorption designs: a Continuous Stirred Tank Reactor (CSTR), and a Steam Stripper Column (SSC). The CSTR is a one-stage separation unit with reduced space requirements, and capital cost. The alternative is a multi-stage separation column, with improved desorption efficiency. Testing the two desorber options allowed us to identify the most cost effective, and space efficient desorber solution. (ii) CSTR Campaign: The CSTR desorber unit was designed, fabricated and integrated with the pilot solvent test unit (PSTU), replacing the PSTU Steam Stripper Column at NCCC. Solvent management and waste water special procedures were implemented to accommodate operation of the non-aqueous solvent in the PSTU. Performance of the GAP-1m solvent with the CSTR was demonstrated for over 500 hrs. while varying temperature of the desorption (230 – 265 oF), solvent circulation rate (GAP-1m : CO 2 (molar) = 1.5 – 4), and flue gas flow rates (0.2 – 0.5 MWe). Solvent carry-over in the CO 2 product was minimized by maintaining water content below 5 wt.%, and desorption pressure at 7 psig. CO 2 capture efficiency achieved was 95% at 0.25 MWe (GAP-1m : CO 2 = 4 (molar), 230 oF desorption), and 65% at 0.5 MWe (GAP-1m : CO 2 (molar) = 1.5, 248 oF). Solvent loss was dominated by thermal degradation of the rich solvent. (iii) Steam Stripper Column Campaign: Higher expected cost of the solvent vs. aqueous amines makes solvent management a top priority to maintain the low cost for the process. During the testing of the GAP-1m solvent with the CSTR, thermal degradation of the rich solvent was found to be the main mechanism in solvent loss. Small amounts of water in the working solution were found to be an effective way to enable steam stripping, thereby lowering desorption temperature, and hence reducing thermal degradation. Steam stripping also increased working capacity by 30% due to a more efficient desorption. The concept was first tested in a glass stripping column (lab scale, GE GRC), optimized in a continuous bench scale system (2 kWe, GE GRC), and demonstrated in a 0.5 MWe PSTU at NCCC. No special system modifications were required to the PSTU to accommodate the testing of the non-aqueous GAP-1 solvent with the regenerator column. SSC was found to be more robust towards solvent entrainment (H 2O < 35 wt.%). 90 – 95% CO 2 capture efficiency was achieved under stoichiometric conditions at 0.5 MWe (235 oF desorption, 2 psig and 19 wt. % H 2O). Both CO 2 capture efficiency and specific duty reached optimum conditions at 18 wt.% H 2O. Low amine degradation (< 0.05 wt.%/day) was recorded over 350 hrs. of operation. Controlled water addition to GAP-1m solvent decreased the desorption temperature, thermal degradation, and improved the CO 2 working capacity due to more efficient absorption and desorption processes. Under these conditions, the GAP-1m solvent exhibited a 25% increased working capacity, and 10% reduction in specific steam duty vs. MEA, at 10 oF lower desorption temperature. (iv) Techno-economic Analysis: The pilot-scale PSTU engineering data were used to update the capture system process models, and the techno-economic analysis was performed for a 550 MW coal fired power plant. The 1st year CO 2 removal cost for the aminosilicone-based carbon-capture process was evaluated at $48/ton CO 2 using the steam stripper column. This is a 20% reduction compared to MEA, primarily due to lower overall capital cost. CO 2 cost using the CSTR desorber is dominated by the economics of the solvent make-up. The steam stripper desorber is the preferred unit operation due to a more efficient desorption, and reduced solvent make-up rate. Further reduction in CO 2 capture cost is expected by lowering the manufacturing cost of the solvent, implementing flowsheet optimization and/or implementing the next generation aminosilicone solvent with improved stability and increased CO 2 working capacity.« less

  15. Barriers and Facilitators to Implementing the HEADS-ED: A Rapid Screening Tool for Pediatric Patients in Emergency Departments.

    PubMed

    MacWilliams, Kate; Curran, Janet; Racek, Jakub; Cloutier, Paula; Cappelli, Mario

    2017-12-01

    This study sought to identify barriers and facilitators to the implementation of the HEADS-ED, a screening tool appropriate for use in the emergency department (ED) that facilitates standardized assessments, discharge planning, charting, and linking pediatric mental health patients to appropriate community resources. A qualitative theory-based design was used to identify barriers and facilitators to implementing the HEADS-ED tool. Focus groups were conducted with participants recruited from 6 different ED settings across 2 provinces (Ontario and Nova Scotia). The Theoretical Domains Framework was used as a conceptual framework to guide data collection and to identify themes from focus group discussions. The following themes spanning 12 domains were identified as reflective of participants' beliefs about the barriers and facilitators to implementing the HEADS-ED tool: knowledge, skills, beliefs about capabilities, social professional role and identity, optimism, beliefs about consequences, reinforcement, environmental context and resources, social influences, emotion, behavioral regulation and memory, and attention and decision process. The HEADS-ED has the potential to address the need for better discharge planning, complete charting, and standardized assessments for the increasing population of pediatric mental health patients who present to EDs. This study has identified potential barriers and facilitators, which should be considered when developing an implementation plan for adopting the HEADS-ED tool into practice within EDs.

  16. Impacted Lower Second Permanent Molars at the Ramus and Coronoid Process: A New Clinical Symptom of the WNT10A Mutation in Ectodermal Dysplasia.

    PubMed

    Sfeir, Elia; Aboujaoude, Samia

    2017-01-01

    Hidrotic ectodermal dysplasia (ED) with the WNT10A mutation produces variable dentofacial symptoms. The aim of this study was to describe a new clinical symptom, i.e., specific to the WNT10A mutation in hidrotic ED. The study investigated the migratory trend of the lower second permanent molars to the ramus or coronoid process. To the best of authors' knowledge, no data in the literature describe this trend in cases of hidrotic ED. A three-generation family pedigree was established for seven families after the diagnosis of hidrotic ED in a 10-year-old boy. Thereafter, a genetic and clinical study was conducted on three families with at least one individual affected by hidrotic ED (20 individuals). We selected the children with molar germs 37 and 47. The eruption axes of these germs were then traced on the panoramic images at the initial time (T 0 ) and 1 year later (T 0 + 1 year), and the deviations between these axes were measured. A significant familial consanguinity was shown. Eight subjects presented with the hidrotic ED phenotype. Among them, three individuals carried germs 37 and 47. Over time, the measured deviations between the eruption axes of the latter displayed, in the majority of the cases, a distal inclination toward the ramus. A larger sample size is mandatory to assess the frequencies and treatment modalities. The presence of germs in the lower second permanent molars in patients with hidrotic ED is an important clinical symptom that should be monitored to detect and prevent ectopic migration of these teeth. In hidrotic ED cases, the study of the presence of the second lower permanent germs must include clinical and radiological examinations. Establishing an inter-ceptive treatment is necessary to prevent the migration of the molars in question. How to cite this article: Sfeir E, Aboujaoude S. Impacted Lower Second Permanent Molars at the Ramus and Coronoid Process: A New Clinical Symptom of the WNT10A Mutation in Ectodermal Dysplasia. Int J Clin Pediatr Dent 2017;10(4):363-368.

  17. Improvement in self-reported confidence in nurses’ professional skills in the emergency department

    PubMed Central

    2013-01-01

    Background The aim of this study was to assess nurses’ self-reported confidence in their professional skills before and after an extensive Emergency Department (ED) reform in Kanta-Häme Central Hospital. Methods Emergency nurses participated in transitional training commencing two years before the establishment of the new organization in 2007. Training was followed by weekly practical educational sessions in the new ED. During this process nurses improved their transition skills, defined house rules for the new clinic and improved their knowledge of new technology and instruments. The main processes involving critically ill ED patients were described and modelled with an electronic flow chart software. During the transitional training nurses compiled lists of practical skills and measures needed in the ED. These were updated after feedback from physicians in primary and secondary care and head physicians in Kanta-Häme Central Hospital. The final 189-item list comprised 15 different categories, each containing from 4 to 35 items. Based on the work described above, a questionnaire was developed to reflect ED nurses’ skills in clinical measures but also to estimate the need for professional education and practical training. Nurses working in the ED were asked to fill the questionnaire in January 2007 (response rate 97%) and in January 2011 (response rate 98%). Results Nurses’ self-reported confidence in their professional skills improved significally in eight classes out of fifteen. These classes were cannulations, urinary catheterizations, patient monitoring, cardiac patients, equipment, triage and nurse practising, psychiatric patients as well as infection risk. Best results were noted in urinary catheterizations, patient monitoring and infection risk. When studying the group of nurses participating in both surveys in 2007 and 2011, improvements were observed in all fifteen categories. All but two of these changes were significant (p<0.05). Conclusions During an extensive reform of emergency services, we noted a significant improvement in the professional skills of nurses. This improvement was especially consistent among nurses working in the ED during the whole transition process. Nurses’ education and training program in the ED may be successfully put into practice when based on co-operation between nurses and physicians dedicated to emergency services. PMID:23497683

  18. Improvement in self-reported confidence in nurses' professional skills in the emergency department.

    PubMed

    Rautava, Veli-Pekka; Palomäki, Erika; Innamaa, Tapio; Perttu, Mika; Lehto, Päivi; Palomäki, Ari

    2013-03-05

    The aim of this study was to assess nurses' self-reported confidence in their professional skills before and after an extensive Emergency Department (ED) reform in Kanta-Häme Central Hospital. Emergency nurses participated in transitional training commencing two years before the establishment of the new organization in 2007. Training was followed by weekly practical educational sessions in the new ED. During this process nurses improved their transition skills, defined house rules for the new clinic and improved their knowledge of new technology and instruments. The main processes involving critically ill ED patients were described and modelled with an electronic flow chart software.During the transitional training nurses compiled lists of practical skills and measures needed in the ED. These were updated after feedback from physicians in primary and secondary care and head physicians in Kanta-Häme Central Hospital. The final 189-item list comprised 15 different categories, each containing from 4 to 35 items. Based on the work described above, a questionnaire was developed to reflect ED nurses' skills in clinical measures but also to estimate the need for professional education and practical training. Nurses working in the ED were asked to fill the questionnaire in January 2007 (response rate 97%) and in January 2011 (response rate 98%). Nurses' self-reported confidence in their professional skills improved significally in eight classes out of fifteen. These classes were cannulations, urinary catheterizations, patient monitoring, cardiac patients, equipment, triage and nurse practising, psychiatric patients as well as infection risk. Best results were noted in urinary catheterizations, patient monitoring and infection risk. When studying the group of nurses participating in both surveys in 2007 and 2011, improvements were observed in all fifteen categories. All but two of these changes were significant (p<0.05). During an extensive reform of emergency services, we noted a significant improvement in the professional skills of nurses. This improvement was especially consistent among nurses working in the ED during the whole transition process. Nurses' education and training program in the ED may be successfully put into practice when based on co-operation between nurses and physicians dedicated to emergency services.

  19. Using voluntary reports from physicians to learn from diagnostic errors in emergency medicine.

    PubMed

    Okafor, Nnaemeka; Payne, Velma L; Chathampally, Yashwant; Miller, Sara; Doshi, Pratik; Singh, Hardeep

    2016-04-01

    Diagnostic errors are common in the emergency department (ED), but few studies have comprehensively evaluated their types and origins. We analysed incidents reported by ED physicians to determine disease conditions, contributory factors and patient harm associated with ED-related diagnostic errors. Between 1 March 2009 and 31 December 2013, ED physicians reported 509 incidents using a department-specific voluntary incident-reporting system that we implemented at two large academic hospital-affiliated EDs. For this study, we analysed 209 incidents related to diagnosis. A quality assurance team led by an ED physician champion reviewed each incident and interviewed physicians when necessary to confirm the presence/absence of diagnostic error and to determine the contributory factors. We generated descriptive statistics quantifying disease conditions involved, contributory factors and patient harm from errors. Among the 209 incidents, we identified 214 diagnostic errors associated with 65 unique diseases/conditions, including sepsis (9.6%), acute coronary syndrome (9.1%), fractures (8.6%) and vascular injuries (8.6%). Contributory factors included cognitive (n=317), system related (n=192) and non-remedial (n=106). Cognitive factors included faulty information verification (41.3%) and faulty information processing (30.6%) whereas system factors included high workload (34.4%) and inefficient ED processes (40.1%). Non-remediable factors included atypical presentation (31.3%) and the patients' inability to provide a history (31.3%). Most errors (75%) involved multiple factors. Major harm was associated with 34/209 (16.3%) of reported incidents. Most diagnostic errors in ED appeared to relate to common disease conditions. While sustaining diagnostic error reporting programmes might be challenging, our analysis reveals the potential value of such systems in identifying targets for improving patient safety in the ED. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

  20. Coal liquefaction process with increased naphtha yields

    DOEpatents

    Ryan, Daniel F.

    1986-01-01

    An improved process for liquefying solid carbonaceous materials wherein the solid carbonaceous material is slurried with a suitable solvent and then subjected to liquefaction at elevated temperature and pressure to produce a normally gaseous product, a normally liquid product and a normally solid product. The normally liquid product is further separated into a naphtha boiling range product, a solvent boiling range product and a vacuum gas-oil boiling range product. At least a portion of the solvent boiling-range product and the vacuum gas-oil boiling range product are then combined and passed to a hydrotreater where the mixture is hydrotreated at relatively severe hydrotreating conditions and the liquid product from the hydrotreater then passed to a catalytic cracker. In the catalytic cracker, the hydrotreater effluent is converted partially to a naphtha boiling range product and to a solvent boiling range product. The naphtha boiling range product is added to the naphtha boiling range product from coal liquefaction to thereby significantly increase the production of naphtha boiling range materials. At least a portion of the solvent boiling range product, on the other hand, is separately hydrogenated and used as solvent for the liquefaction. Use of this material as at least a portion of the solvent significantly reduces the amount of saturated materials in said solvent.

  1. Highly hydrophilic poly(vinylidene fluoride)/meso-titania hybrid mesoporous membrane for photocatalytic membrane reactor in water

    NASA Astrophysics Data System (ADS)

    Wang, Meng; Yang, Guang; Jin, Peng; Tang, Hao; Wang, Huanhuan; Chen, Yong

    2016-01-01

    The high hydrophobicity of poly(vinylidene fluoride) (PVDF) membrane remains an obstacle to be applied in some purification processes of water or wastewater. Herein, a highly hydrophilic hybrid mesoporous titania membrane composed of mesoporous anatase titania (meso-TiO2) materials inside the three-dimensional (3D) macropores of PVDF membrane was successfully prepared by using the dual-templated synthesis method combined with solvent extraction and applied as the photocatalytic membrane reactor for the photodegredation of organic dye in water. The structure and the properties of as-prepared hybrid membranes were characterized by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), transmission electron microscopy (TEM), X-ray diffraction (XRD), nitrogen adsorption-desorption and contact angle measurements. It was found that the hydrophilicity of PVDF membrane can be significantly improved by filling mesoporous TiO2 inside the 3D macropores of PVDF membrane. Moreover, such a PVDF/meso-TiO2 hybrid membrane exhibits promising photocatalytic degradation of dye in water due to the existence of mesoporous anatase TiO2 materials inside PVDF membrane. This study provides a new strategy to simultaneously introduce hydrophilicity and some desirable properties into PVDF and other hydrophobic membranes.

  2. Sonosynthesis of nano TiO2 on wool using titanium isopropoxide or butoxide in acidic media producing multifunctional fabric.

    PubMed

    Behzadnia, Amir; Montazer, Majid; Rashidi, Abousaeid; Rad, Mahnaz Mahmoudi

    2014-09-01

    This study presents a novel idea to prepare nanocrystalline structure of TiO2 under ambient pressure at 60-65 °C using in situ sonochemical synthesis by hydrolysis of either titanium isopropoxide or titanium butoxide in an acidic aqueous solution. The nano titanium dioxide coated wool fabrics possess significant antibacterial/antifungal activity and self-cleaning property by discoloring Methylene blue stain under sunlight irradiation. This process has no negative effect on cytotoxicity and tensile strength of the sonotreated fabric even reduces alkaline solubility and photoyellowing and improves hydrophilicity. More titanium isopropoxide or titanium butoxide as a precursor led to higher photocatalytic activities of the treated fabrics. Also introducing more ethanol improved the adsorption of TiO2 on the wool fabric surface leading to enhanced photocatalytic activity. EDS and XRD patterns, SEM images, X-ray mapping confirmed the presence of nano TiO2 particles on the fabric surface. The role of both solvent and precursor concentrations on the various properties of the fabric was investigated and the optimized conditions were obtained using response surface methodology. Copyright © 2014 Elsevier B.V. All rights reserved.

  3. Influence of film structure on the dewetting kinetics of thin polymer films in the solvent annealing process.

    PubMed

    Zhang, Huanhuan; Xu, Lin; Lai, Yuqing; Shi, Tongfei

    2016-06-28

    On a non-wetting solid substrate, the solvent annealing process of a thin polymer film includes the swelling process and the dewetting process. Owing to difficulties in the in situ analysis of the two processes simultaneously, a quantitative study on the solvent annealing process of thin polymer films on the non-wetting solid substrate is extremely rare. In this paper, we design an experimental method by combining spectroscopic ellipsometry with optical microscopy to achieve the simultaneous in situ study. Using this method, we investigate the influence of the structure of swollen film on its dewetting kinetics during the solvent annealing process. The results show that for a thin PS film with low Mw (Mw = 4.1 kg mol(-1)), acetone molecules can form an ultrathin enriched layer between the PS film and the solid substrate during the swelling process. The presence of the acetone enriched layer accounts for the exponential kinetic behavior in the case of a thin PS film with low Mw. However, the acetone enriched layer is not observed in the case of a thin PS film with high Mw (Mw = 400 kg mol(-1)) and the slippage effect of polymer chains is valid during the dewetting process.

  4. PARALLEL MULTIOBJECTIVE EVOLUTIONARY ALGORITHMS FOR WASTE SOLVENT RECYCLING

    EPA Science Inventory

    Waste solvents are of great concern to the chemical process industries and to the public, and many technologies have been suggested and implemented in the chemical process industries to reduce waste and associated environmental impacts. In this article we have developed a novel p...

  5. Zinc sulfide liquefaction catalyst

    DOEpatents

    Garg, Diwakar

    1984-01-01

    A process for the liquefaction of carbonaceous material, such as coal, is set forth wherein coal is liquefied in a catalytic solvent refining reaction wherein an activated zinc sulfide catalyst is utilized which is activated by hydrogenation in a coal derived process solvent in the absence of coal.

  6. Study protocol for evaluating the implementation and effectiveness of an emergency department longitudinal patient monitoring system using a mixed-methods approach.

    PubMed

    Ward, Marie; McAuliffe, Eilish; Wakai, Abel; Geary, Una; Browne, John; Deasy, Conor; Schull, Michael; Boland, Fiona; McDaid, Fiona; Coughlan, Eoin; O'Sullivan, Ronan

    2017-01-23

    Early detection of patient deterioration is a key element of patient safety as it allows timely clinical intervention and potential rescue, thus reducing the risks of serious patient safety incidents. Longitudinal patient monitoring systems have been widely recommended for use to detect clinical deterioration. However, there is conflicting evidence on whether they improve patient outcomes. This may in part be related to variation in the rigour with which they are implemented and evaluated. This study aims to evaluate the implementation and effectiveness of a longitudinal patient monitoring system designed for adult patients in the unique environment of the Emergency Department (ED). A novel participatory action research (PAR) approach is taken where socio-technical systems (STS) theory and analysis informs the implementation through the improvement methodology of 'Plan Do Study Act' (PDSA) cycles. We hypothesise that conducting an STS analysis of the ED before beginning the PDSA cycles will provide for a much richer understanding of the current situation and possible challenges to implementing the ED-specific longitudinal patient monitoring system. This methodology will enable both a process and an outcome evaluation of implementing the ED-specific longitudinal patient monitoring system. Process evaluations can help distinguish between interventions that have inherent faults and those that are badly executed. Over 1.2 million patients attend EDs annually in Ireland; the successful implementation of an ED-specific longitudinal patient monitoring system has the potential to affect the care of a significant number of such patients. To the best of our knowledge, this is the first study combining PAR, STS and multiple PDSA cycles to evaluate the implementation of an ED-specific longitudinal patient monitoring system and to determine (through process and outcome evaluation) whether this system can significantly improve patient outcomes by early detection and appropriate intervention for patients at risk of clinical deterioration.

  7. Effect of HEH[EHP] impurities on the ALSEP solvent extraction process

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Holfeltz, Vanessa E.; Campbell, Emily L.; Peterman, Dean R.

    In solvent extraction processes, organic phase impurities can negatively impact separation factors, hydrolytic performance, and overall system robustness. This affects the process-level viability of a separation concept and necessitates knowledge of the behavior and mechanisms to control impurities in the solvent. The most widespread way through which impurities are introduced into a system is through impure extractants and/or diluents used to prepare the solvent, and often development of new purification schemes to achieve the desired level of purity is needed. In this work, the acidic extractant, 2-ethylhexylphosphonic acid mono-2-ethylhexyl ester (HEH[EHP])—proposed for application in extractive processes aimed at separating trivalentmore » minor actinides from lanthanides and other fission products—is characterized with respect to its common impurities and their impact on Am(III) stripping in the Actinide Lanthanide SEParation (ALSEP) system. To control impurities in HEH[EHP], existing purification technologies commonly applied for the acidic organophosphorus reagents are reviewed, and a new method specific to HEH[EHP] purification is presented.« less

  8. Research in Stochastic Processes

    DTIC Science & Technology

    1988-10-10

    To appear in Proceedings Volume, Oberwolfach Conf. on Extremal Value Theory, Ed. J. HUsler and R. Reiss, Springer. 4. M.R. Leadbetter. The exceedance...Hsing, J. Husler and M.R. Leadbetter, On the exceedance point process for a stationary sequence, Probability Theor. Rel. Fields, 20, 1988, 97-112 Z.J...Oberwotfach Conf. on Extreme Value Theory. J. Husler and R. Reiss. eds.. Springer. to appear V. Mandrekar, On a limit theorem and invariance

  9. A novel process for direct production of acetone-butanol-ethanol from native starches using granular starch hydrolyzing enzyme by Clostridium saccharoperbutylacetonicum N1-4.

    PubMed

    Thang, Vu Hong; Kobayashi, Genta

    2014-02-01

    In this work, a new approach for acetone-butanol-ethanol (ABE) production has been proposed. Direct fermentation of native starches (uncooked process) was investigated by using granular starch hydrolyzing enzyme (GSHE) and Clostridium saccharoperbutylacetonicum N1-4. Even the process was carried out under suboptimal condition for activity of GSHE, the production of ABE was similar with that observed in conventional process or cooked process in terms of final solvent concentration (21.3 ± 0.4 to 22.4 ± 0.4 g/L), butanol concentration (17.5 ± 0.4 to 17.8 ± 0.3 g/L) and butanol yield (0.33 to 0.37 g/g). The production of solvents was significantly dependent on the source of starches. Among investigated starches, corn starch was more susceptible to GSHE while cassava starch was the most resistant to this enzyme. Fermentation using native corn starch resulted in the solvent productivity of 0.47 g/L h, which was about 15 % higher than that achieved in cooked process. On the contrary, uncooked process using cassava and wheat starch resulted in the solvent productivity of 0.30 and 0.37 g/L h, which were respectively about 30 % lower than those obtained in cooked process. No contamination was observed during all trials even fermentation media were prepared without sterilization. During the fermentation using native starches, no formation of foam is observed. This uncooked process does not require cooking starchy material; therefore, the thermal energy consumption for solvent production would remarkably be reduced in comparison with cooked process.

  10. Green ultrasound-assisted extraction of carotenoids from pomegranate wastes using vegetable oils.

    PubMed

    Goula, Athanasia M; Ververi, Maria; Adamopoulou, Anna; Kaderides, Kyriakos

    2017-01-01

    The objective of this work was to develop a new process for pomegranate peels application in food industries based on ultrasound-assisted extraction of carotenoids using different vegetable oils as solvents. In this way, an oil enriched with antioxidants is produced. Sunflower oil and soy oil were used as alternative solvents and the effects of various parameters on extraction yield were studied. Extraction temperature, solid/oil ratio, amplitude level, and extraction time were the factors investigated with respect to extraction yield. Comparative studies between ultrasound-assisted and conventional solvent extraction were carried out in terms of processing procedure and total carotenoids content. The efficient extraction period for achieving maximum yield of pomegranate peel carotenoids was about 30min. The optimum operating conditions were found to be: extraction temperature, 51.5°C; peels/solvent ratio, 0.10; amplitude level, 58.8%; solvent, sunflower oil. A second-order kinetic model was successfully developed for describing the mechanism of ultrasound extraction under different processing parameters. Copyright © 2016 Elsevier B.V. All rights reserved.

  11. Green Processing of Lignocellulosic Biomass and Its Derivatives in Deep Eutectic Solvents.

    PubMed

    Tang, Xing; Zuo, Miao; Li, Zheng; Liu, Huai; Xiong, Caixia; Zeng, Xianhai; Sun, Yong; Hu, Lei; Liu, Shijie; Lei, Tingzhou; Lin, Lu

    2017-07-10

    The scientific community has been seeking cost-competitive and green solvents with good dissolving capacity for the valorization of lignocellulosic biomass. At this point, deep eutectic solvents (DESs) are currently emerging as a new class of promising solvents that are generally liquid eutectic mixtures formed by self-association (or hydrogen-bonding interaction) of two or three components. DESs are attractive solvents for the fractionation (or pretreatment) of lignocellulose and the valorization of lignin, owing to the high solubility of lignin in DESs. DESs are also employed as effective media for the modification of cellulose to afford functionalized cellulosic materials, such as cellulose nanocrystals. More interestingly, biomassderived carbohydrates, such as fructose, can be used as one of the constituents of DESs and then dehydrated to 5-hydroxymethylfurfural in high yield. In this review, a comprehensive summary of recent contribution of DESs to the processing of lignocellulosic biomass and its derivatives is provided. Moreover, further discussion about the challenges of the application of DESs in biomass processing is presented. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  12. Characteristics of older people with cognitive impairment attending emergency departments: A descriptive study.

    PubMed

    Schnitker, Linda M; Beattie, Elizabeth R A; Martin-Khan, Melinda; Burkett, Ellen; Gray, Leonard C

    2016-05-01

    The objective of this paper is to describe the profile of older people with cognitive impairment (CI) presenting to emergency departments (EDs). This was a multi-centre (n=8) observational study of a convenience sample of older (≥70y) ED patients (n=579). Participants were prospectively assessed for CI and surveyed for the duration of their ED stay (n=191). A picture of patients' health status and ED responses to care needs was obtained through application of standardised assessment tools. Additionally, observations of care processes in ED were undertaken. Demographic data were collected through both ED's information system and survey. Outcome data were collected 28 days post-ED visit using follow-up telephone interviews. Of 579 older persons, 191 (33%) persons met criteria for CI. The majority of older ED patients with CI in ED lived in the community (157/177, 88.7%), arrived by ambulance (116/172, 67%), were accompanied by a support person (94/149, 63%), were triaged as urgent to semi-urgent (157/191, 82%), and were hospitalised (108/172, 57%). The median ED length of stay was 6h. In ED, 53% of the sample experienced pain (92/173). Older ED patients with CI pose the following characteristics: prior hospital admissions (43/129, 33%), incontinence (61/178, 34%), dependence in activities in daily living (81/190, 43%), issues in nutrition (73/182, 40%), vision and hearing impairment (93% (160/172) and 26% (44/171) respectively). Increased understanding of these presenting characteristics and their impacts on patient risk facilitates tailoring the quality of emergency care to better suit the needs and improve outcomes of this increasing ED population. Copyright © 2016 College of Emergency Nursing Australasia. Published by Elsevier Ltd. All rights reserved.

  13. The influence of solvent processing on polyester bioabsorbable polymers.

    PubMed

    Manson, Joanne; Dixon, Dorian

    2012-01-01

    Solvent-based methods are commonly employed for the production of polyester-based samples and coatings in both medical device production and research. The influence of solvent casting and subsequent drying time was studied using thermal analysis, spectroscopy and weight measurement for four grades of 50 : 50 poly(lactic-co-glycolic acid) (PLGA) produced by using chloroform, dichloromethane, and acetone. The results demonstrate that solvent choice and PLGA molecular weight are critical factors in terms of solvent removal rate and maintaining sample integrity, respectively. The protocols widely employed result in high levels of residual solvent and a new protocol is presented together with solutions to commonly encountered problems.

  14. Step-wise supercritical extraction of carbonaceous residua

    DOEpatents

    Warzinski, Robert P.

    1987-01-01

    A method of fractionating a mixture containing high boiling carbonaceous material and normally solid mineral matter includes processing with a plurality of different supercritical solvents. The mixture is treated with a first solvent of high critical temperature and solvent capacity to extract a large fraction as solute. The solute is released as liquid from solvent and successively treated with other supercritical solvents of different critical values to extract fractions of differing properties. Fractionation can be supplemented by solute reflux over a temperature gradient, pressure let down in steps and extractions at varying temperature and pressure values.

  15. Redesigning emergency department patient flows: application of Lean Thinking to health care.

    PubMed

    King, Diane L; Ben-Tovim, David I; Bassham, Jane

    2006-08-01

    To describe in some detail the methods used and outcome of an application of concepts from Lean Thinking in establishing streams for patient flows in a teaching general hospital ED. Detailed understanding was gained through process mapping with staff followed by the identification of value streams (those patients likely to be discharged from the ED, those who were likely to be admitted) and the implementation of a process of seeing those patients that minimized complex queuing in the ED. Streaming had a significant impact on waiting times and total durations of stay in the ED. There was a general flattening of the waiting time across all groups. A slight increase in wait for Triage categories 2 and 3 patients was offset by reductions in wait for Triage category 4 patients. All groups of patients spent significantly less overall time in the department and the average number of patients in the ED at any time decreased. There was a significant reduction in number of patients who do not wait and a slight decrease in access block. The streaming of patients into groups of patients cared for by a specific team of doctors and nurses, and the minimizing of complex queues in this ED by altering the practices in relation to the function of the Australasian Triage Scale improved patient flow, thereby decreasing potential for overcrowding.

  16. Dissolution of covalent adaptable network polymers in organic solvent

    NASA Astrophysics Data System (ADS)

    Yu, Kai; Yang, Hua; Dao, Binh H.; Shi, Qian; Yakacki, Christopher M.

    2017-12-01

    It was recently reported that thermosetting polymers can be fully dissolved in a proper organic solvent utilizing a bond-exchange reaction (BER), where small molecules diffuse into the polymer, break the long polymer chains into short segments, and eventually dissolve the network when sufficient solvent is provided. The solvent-assisted dissolution approach was applied to fully recycle thermosets and their fiber composites. This paper presents the first multi-scale modeling framework to predict the dissolution kinetics and mechanics of thermosets in organic solvent. The model connects the micro-scale network dynamics with macro-scale material properties: in the micro-scale, a model is developed based on the kinetics of BERs to describe the cleavage rate of polymer chains and evolution of chain segment length during the dissolution. The micro-scale model is then fed into a continuum-level model with considerations of the transportation of solvent molecules and chain segments in the system. The model shows good prediction on conversion rate of functional groups, degradation of network mechanical properties, and dissolution rate of thermosets during the dissolution. It identifies the underlying kinetic factors governing the dissolution process, and reveals the influence of different material and processing variables on the dissolution process, such as time, temperature, catalyst concentration, and chain length between cross-links.

  17. Solvent-Free Manufacturing of Electrodes for Lithium-ion Batteries

    NASA Astrophysics Data System (ADS)

    Ludwig, Brandon; Zheng, Zhangfeng; Shou, Wan; Wang, Yan; Pan, Heng

    2016-03-01

    Lithium ion battery electrodes were manufactured using a new, completely dry powder painting process. The solvents used for conventional slurry-cast electrodes have been completely removed. Thermal activation time has been greatly reduced due to the time and resource demanding solvent evaporation process needed with slurry-cast electrode manufacturing being replaced by a hot rolling process. It has been found that thermal activation time to induce mechanical bonding of the thermoplastic polymer to the remaining active electrode particles is only a few seconds. Removing the solvent and drying process allows large-scale Li-ion battery production to be more economically viable in markets such as automotive energy storage systems. By understanding the surface energies of various powders which govern the powder mixing and binder distribution, bonding tests of the dry-deposited particles onto the current collector show that the bonding strength is greater than slurry-cast electrodes, 148.8 kPa as compared to 84.3 kPa. Electrochemical tests show that the new electrodes outperform conventional slurry processed electrodes, which is due to different binder distribution.

  18. CHEMICAL SUBSTITUTION FOR 1,1,1-TRICHLOROETHANE AND METHANOL IN AN INDUSTRIAL CLEANING OPERATION

    EPA Science Inventory

    Hazardous wastes are generated from cold solvent degreasing operations used in many industrial processes. he spent solvents are managed under Subtitle C of the Resource Conservation and Recovery Act (RCRA). ith the land ban of spent solvents, disposal has become increasingly diff...

  19. CHEMICAL SUBSTITUTION FOR 1,1,1-TRICHLOROETHANE AND METHANOL IN AN INDUSTRIAL CLEANING OPERATION

    EPA Science Inventory

    Hazardous wastes are generated from cold solvent degreasing operations used in many industrial processes. The spent solvents are managed under Subtitle C of the Resource Conservation and Recovery Act (RCRA). With the land ban of spent solvents, disposal has become increasingly di...

  20. EPA's science blog: "It All Starts with Science"; Article title: "EPA's Solvent Substitution Software Tool, PARIS III"

    EPA Science Inventory

    EPA's solvent substitution software tool, PARIS III is provided by the EPA for free, and can be effective and efficiently used to help environmentally-conscious individuals find better and greener solvent mixtures for many different common industrial processes. People can downlo...

  1. Advanced separators based on aromatic polymer for high energy density lithium batteries

    DOEpatents

    Zhang, Zhengcheng; Woo, Jung-Je; Amine, Khalil

    2017-03-21

    A process includes casting a solution including poly(phenylene oxide), inorganic nanoparticles, a solvent, and a non-solvent on a substrate; and removing the solvent to form a porous film; wherein: the porous film is configured for use as a porous separator for a lithium ion battery.

  2. Momentary fitting in a fluid environment: A grounded theory of triage nurse decision making.

    PubMed

    Reay, Gudrun; Rankin, James A; Then, Karen L

    2016-05-01

    Triage nurses control access to the Emergency Department (ED) and make decisions about patient acuity, patient priority, and placement of the patient in the ED. Understanding the processes and strategies that triage nurses use to make decisions is therefore vital for patient safety and the operation of the ED. The aim of the current study was to generate a substantive grounded theory (GT) of decision making by emergency triage Registered Nurses (RNs). Data collection consisted of seven observations of the triage environment at three tertiary care hospitals where RNs conducted triage and twelve interviews with triage RNs. The data were analyzed by constant comparison in accordance with the classical GT method. In the resultant theory, Momentary Fitting in a Fluid Environment, triage is conceptualized as a process consisting of four categories, determining acuity, anticipating needs, managing space, and creating space. The findings indicate that triage RNs continually strive to achieve fit, while simultaneously considering the individual patient and the ED as a whole entity. Triage RNs require appropriately designed triage environments and computer technology that enable them to secure real time knowledge of the ED to maintain situation awareness. Copyright © 2015 Elsevier Ltd. All rights reserved.

  3. Literature survey of properties of synfuels derived from coal

    NASA Technical Reports Server (NTRS)

    Flores, F.

    1982-01-01

    A literature survey of the properties of synfuels for ground-based turbine applications is presented. The four major concepts for converting coal into liquid fuels (solvent extraction, catalytic liquefaction, pyrolysis, and indirect liquefaction), and the most important concepts for coal gasification (fixed bed, fluidized bed, entrained flow, and underground gasification) are described. Upgrading processes for coal derived liquid fuels are also described. Data presented for liquid fuels derived from various processes, including H-coal, synthoil, solvent refined coal, COED, donor solvent, zinc chloride hydrocracking, co-steam, and flash pyrolysis. Typical composition, and property data is also presented for low and medium-BTU gases derived from the various coal gasification processes.

  4. SOLVENT EXTRACTION PROCESS FOR THE RECOVERY OF METALS FROM PHOSPHORIC ACID

    DOEpatents

    Bailes, R.H.; Long, R.S.

    1958-11-01

    > A solvent extraction process is presented for recovering metal values including uranium, thorium, and other lanthanide and actinide elements from crude industrial phosphoric acid solutions. The process conslsts of contacting said solution with an immisclble organic solvent extractant containing a diluent and a material selected from the group consisting of mono and di alkyl phosphates, alkyl phosphonates and alkyl phosphites. The uranlum enters the extractant phase and is subsequently recovered by any of the methods known to the art. Recovery is improved if the phosphate solution is treated with a reducing agent such as iron or aluminum powder prior to the extraction step.

  5. Two-Step Process for ED UTI Screening in Febrile Young Children: Reducing Catheterization Rates.

    PubMed

    Lavelle, Jane M; Blackstone, Mercedes M; Funari, Mary Kate; Roper, Christine; Lopez, Patricia; Schast, Aileen; Taylor, April M; Voorhis, Catherine B; Henien, Mira; Shaw, Kathy N

    2016-07-01

    Urinary tract infection (UTI) screening in febrile young children can be painful and time consuming. We implemented a screening protocol for UTI in a high-volume pediatric emergency department (ED) to reduce urethral catheterization, limiting catheterization to children with positive screens from urine bag specimens. This quality-improvement initiative was implemented using 3 Plan-Do-Study-Act cycles, beginning with a small test of the proposed change in 1 ED area. To ensure appropriate patients received timely screening, care teams discussed patient risk factors and created patient-specific, appropriate procedures. The intervention was extended to the entire ED after providing education. Finally, visual cues were added into the electronic health record, and nursing scripts were developed to enlist family participation. A time-series design was used to study the impact of the 6-month intervention by using a p-chart to determine special cause variation. The primary outcome measure for the study was defined as the catheterization rate in febrile children ages 6 to 24 months. The ED reduced catheterization rates among febrile young children from 63% to <30% over a 6-month period with sustained results. More than 350 patients were spared catheterization without prolonging ED length of stay. Additionally, there was no change in the revisit rate or missed UTIs among those followed within the hospital's network. A 2-step less-invasive process for screening febrile young children for UTI can be instituted in a high-volume ED without increasing length of stay or missing cases of UTI. Copyright © 2016 by the American Academy of Pediatrics.

  6. "My child can't keep anything down!" Interviewing parents who bring their preschoolers to the emergency department for diarrhea, vomiting, and dehydration.

    PubMed

    Graham, Jennifer M; Fitzpatrick, Eleanor A; Black, Karen J L

    2010-04-01

    Viral gastroenteritis with dehydration is one of the most frequent reasons for visits to pediatric emergency departments (ED). Parental intervention before presentation to the ED can make a significant difference in the course of a child's illness. There is a discrepancy between medical knowledge of dehydration and parental fears and understanding. This project is part of a larger program of research developing an educational tool for parents of preschoolers with diarrhea, vomiting, and dehydration. The primary objective was to develop an interview guide. From initial data, the researchers explored parental motivations for bringing their children to the ED. Ten families were recruited after their visit to a pediatric ED in the fall of 2007. Included were families of children younger than 4 years who experienced vomiting, diarrhea, and dehydration. Interviews were conducted over the telephone and were transcribed. The interview guide was edited in an iterative process. Thematic analysis focused on parents' decision to take their child to the ED. Making the decision to take a child to the ED is a complex process for parents. This decision involves expectations developed from community-level, family-level, and child factors. Issues of access to care affect parents' decision, including perceived level of urgency, travel time, and modes of transport available. A framework is proposed, which outlines the most important factors our sample of parents reported when deciding whether to take their ill child to the ED. The interview guide developed will facilitate collection of further information.

  7. Care processes associated with quicker door-in-door-out times for patients with ST-elevation-myocardial infarction requiring transfer: results from a statewide regionalization program.

    PubMed

    Glickman, Seth W; Lytle, Barbara L; Ou, Fang-Shu; Mears, Greg; O'Brien, Sean; Cairns, Charles B; Garvey, J Lee; Bohle, David J; Peterson, Eric D; Jollis, James G; Granger, Christopher B

    2011-07-01

    The ability to rapidly identify patients with ST-segment elevation-myocardial infarction (STEMI) at hospitals without percutaneous coronary intervention (PCI) and transfer them to hospitals with PCI capability is critical to STEMI regionalization efforts. Our objective was to assess the association of prehospital, emergency department (ED), and hospital processes of care implemented as part of a statewide STEMI regionalization program with door-in-door-out times at non-PCI hospitals. Door-in-door-out times for 436 STEMI patients at 55 non-PCI hospitals were determined before (July 2005 to September 2005) and after (January 2007 to March 2007) a year-long implementation of standardized protocols as part of a statewide regionalization program (Reperfusion of Acute Myocardial Infarction in North Carolina Emergency Departments, RACE). The association of 8 system care processes (encompassing emergency medical services [EMS], ED, and hospital settings) with door-in-door-out times was determined using multivariable linear regression. Median door-in-door-out times improved significantly with the intervention (before: 97.0 minutes, interquartile range, 56.0 to 160.0 minutes; after: 58.0 minutes, interquartile range, 35.0 to 90.0 minutes; P<0.0001). Hospital, ED, and EMS care processes were each independently associated with shorter door-in-door-out times (-17.7 [95% confidence interval, -27.5 to -7.9]; -10.1 [95% confidence interval, -19.0 to -1.1], and -7.3 [95% confidence interval, -13.0 to -1.5] minutes for each additional hospital, ED, and EMS process, respectively). Combined, adoption of EMS processes was associated with the shortest median treatment times (44 versus 138 minutes for hospitals that adopted all EMS processes versus none). Prehospital, ED, and hospital processes of care were independently associated with shorter door-in-door-out times for STEMI patients requiring transfer. Adoption of several EMS processes was associated with the largest reduction in treatment times. These findings highlight the need for an integrated, system-based approach to improving STEMI care.

  8. Microwave-Assisted γ-Valerolactone Production for Biomass Lignin Extraction: A Cascade Protocol.

    PubMed

    Tabasso, Silvia; Grillo, Giorgio; Carnaroglio, Diego; Calcio Gaudino, Emanuela; Cravotto, Giancarlo

    2016-03-26

    The general need to slow the depletion of fossil resources and reduce carbon footprints has led to tremendous effort being invested in creating "greener" industrial processes and developing alternative means to produce fuels and synthesize platform chemicals. This work aims to design a microwave-assisted cascade process for a full biomass valorisation cycle. GVL (γ-valerolactone), a renewable green solvent, has been used in aqueous acidic solution to achieve complete biomass lignin extraction. After lignin precipitation, the levulinic acid (LA)-rich organic fraction was hydrogenated, which regenerated the starting solvent for further biomass delignification. This process does not requires a purification step because GVL plays the dual role of solvent and product, while the reagent (LA) is a product of biomass delignification. In summary, this bio-refinery approach to lignin extraction is a cascade protocol in which the solvent loss is integrated into the conversion cycle, leading to simplified methods for biomass valorisation.

  9. Organic microchemical performance of solvent resistant polycarbosilane based microreactor.

    PubMed

    Yoon, Tae-Ho; Jung, Sang-Hee; Kim, Dong-Pyo

    2011-05-01

    We report the successful fabrication of preceramic polymer allylhydridopolycarbosilane (AHPCS) derived microchannels with excellent organic solvent resistance and optical transparency via economic imprinting process, followed by UV and post thermal curing process at 160 degrees C for 3 h. The microchemical performance of the fabricated microreactors was evaluated by choosing two model micro chemical reactions under organic solvent conditions; syntheses of 2-aminothiazole in DMF and dimethylpyrazole in THF, and compared with glass-based microreactor having identical dimensions and batch system with analogy. It is clear that AHPCS derived microreactor showed excellent solvent resistance and chemical stability compare with glass derived microreactor made by high cost of photolithography and thermal bonding process. The novel preceramic polymer derived microreactors showed reliable mechanical and chemical stability and conversion yields compare with that of glass derived microreactors, which is very promising for developing an integrated microfluidics by adopting available microstructuring techniques of the polymers.

  10. Reactive extraction at liquid-liquid systems

    NASA Astrophysics Data System (ADS)

    Wieszczycka, Karolina

    2018-01-01

    The chapter summarizes the state of knowledge about a metal transport in two-phase system. The first part of this review focuses on the distribution law and main factors determination in classical solvent extraction (solubility and polarity of the solute, as well as inter- and intramolecules interaction. Next part of the chapter is devoted to the reactive solvent extraction and the molecular modeling requiring knowledge on type of extractants, complexation mechanisms, metals ions speciation and oxidation during complexes forming, and other parameters that enable to understand the extraction process. Also the kinetic data that is needed for proper modeling, simulation and design of processes needed for critical separations are discussed. Extraction at liquid-solid system using solvent impregnated resins is partially identical as in the case of the corresponding solvent extraction, therefore this subject was also presented in all aspects of separation process (equilibrium, mechanism, kinetics).

  11. Study of the solid state of carbamazepine after processing with gas anti-solvent technique.

    PubMed

    Moneghini, M; Kikic, I; Voinovich, D; Perissutti, B; Alessi, P; Cortesi, A; Princivalle, F; Solinas, D

    2003-09-01

    The purpose of this study was to investigate the influence of supercritical CO2 processing on the physico-chemical properties of carbamazepine, a poorly soluble drug. The gas anti-solvent (GAS) technique was used to precipitate the drug from three different solvents (acetone, ethylacetate and dichloromethane) to study how they would affect the final product. The samples were analysed before and after treatment by scanning electron microscopy analysis and laser granulometry for possible changes in the habitus of the crystals. In addition, the solid state of the samples was studied by means of X-ray powder diffraction, differential scanning calorimetry, diffuse reflectance Fourier-transform infrared spectroscopy and hot stage microscopy. Finally, the in vitro dissolution tests were carried out. The solid state analysis of both samples untreated and treated with CO2, showed that the applied method caused a transition from the starting form III to the form I as well as determined a dramatic change of crystal morphology, resulting in needle-shaped crystals, regardless of the chosen solvent. In order to identify which process was responsible for the above results, carbamazepine was further precipitated from the same three solvents by traditional evaporation method (RV-samples). On the basis of this cross-testing, the solvents were found to be responsible for the reorganisation into a different polymorphic form, and the potential of the GAS process to produce micronic needle shaped particles, with an enhanced dissolution rate compared to the RV-carbamazepine, was ascertained.

  12. Direct Coal -to-Liquids (CTL) for Jet Fuel Using Biomass-Derived Solvents

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Chauhan, Satya P.; Garbark, Daniel B.; Taha, Rachid

    Battelle has demonstrated a novel and potentially breakthrough technology for a direct coal-to-liquids (CTL) process for producing jet fuel using biomass-derived coal solvents (bio-solvents). The Battelle process offers a significant reduction in capital and operating costs and a substantial reduction in greenhouse gas (GHG) emissions, without requiring carbon capture and storage (CCS). The results of the project are the advancement of three steps of the hybrid coal/biomass-to-jet fuel process to the technology readiness level (TRL) of 5. The project objectives were achieved over two phases. In Phase 1, all three major process steps were explored and refined at bench-scale, including:more » (1) biomass conversion to high hydrogen-donor bio-solvent; (2) coal dissolution in biomass-derived bio-solvent, without requiring molecular H 2, to produce a synthetic crude (syncrude); and (3) two-stage catalytic hydrotreating/hydrogenation of syncrude to jet fuel and other distillates. In Phase 2, all three subsystems of the CTL process were scaled up to a pre-pilot scale, and an economic analysis was carried out. A total of over 40 bio-solvents were identified and prepared. The most unique attribute of Battelle’s bio-solvents is their ability to provide much-needed hydrogen to liquefy coal and thus increase its hydrogen content so much that the resulting syncrude is liquid at room temperature. Based on the laboratory-scale testing with bituminous coals from Ohio and West Virginia, a total of 12 novel bio-solvent met the goal of greater than 80% coal solubility, with 8 bio-solvents being as good as or better than a well-known but expensive hydrogen-donor solvent, tetralin. The Battelle CTL process was then scaled up to 1 ton/day (1TPD) at a pre-pilot facility operated in Morgantown, WV. These tests were conducted, in part, to produce enough material for syncrude-upgrading testing. To convert the Battelle-CTL syncrude into a form suitable as a blending stock for jet turbine fuel, a two-step catalytic upgrading process was developed at laboratory scale and then demonstrated at pre-pilot scale facility in Pittsburg, PA. Several drums of distillate products were produced, which were then distilled into unblended (neat) synthetic jet fuel and diesel products for a detailed characterization. Based on a detailed characterization of the synthetic jet fuel, a 20% synthetic, 80% commercial jet fuel blend was prepared, which met all specifications. An analysis of the synthetic diesel product showed that it has the promise of being a drop-in fuel as super-low (less than 15 ppm)-sulfur diesel fuel. A detailed economic analysis showed that the Battelle liquefaction process is economical at between 1000 metric tons/day (MT/day) and 2000 MT/day. The unit capital cost for Battelle CTL process for making jet fuel is 50K USD/daily bbl compared to 151K USD/daily bbl for indirect CTL, based on 2011 dollars. The jet-fuel selling cost at the refinery, including a 12% capital cost factor (which included profit), for the Battelle CTL process is 61USD/bbl (1.45 USD/gallon). This is competitive with crude oil price of 48 USD/bbl. At the same time, the GHG emissions of 3.56 MT CO 2/MT fuel were lower than the GHG emissions of 3.79 MT CO 2/MTfuel for petroleum-based fuels and 7.77 MT CO 2/MT fuel for indirect CTL. Thus, the use of bio-solvents completely eliminates the need for carbon capture in the case of Battelle CTL process. The superior economics and low GHG emissions for the Battelle CTL process has thus sparked worldwide interest and some potential commercialization opportunities are emerging.« less

  13. 40 CFR 63.1323 - Batch process vents-methods and procedures for group determination.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... accepted chemical engineering principles, measurable process parameters, or physical or chemical laws or... recovering monomer, reaction products, by-products, or solvent from a stripper operated in batch mode, and the primary condenser recovering monomer, reaction products, by-products, or solvent from a...

  14. Investigation of In-situ Biogeochemical Reduction of Chlorinated Solvents in Groundwater by Reduced Iron Minerals

    EPA Science Inventory

    Biogeochemical transformation is a process in which chlorinated solvents are degraded abiotically by reactive minerals formed by, at least in part or indirectly from, anaerobic biological processes. Five mulch biowall and/or vegetable oil-based bioremediation applications for tr...

  15. CMPO purity tests in the TRUEX solvent using americium-241

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Brewer, K.N.; Herbst, R.S.; Tranter, T.J.

    1993-12-01

    The Transuranic Extraction (TRUEX) Process was developed by E.P. Horwitz and coworkers at Argonne National Laboratory (ANL) to separate the +4, +6, and +3 actinides from acidic aqueous solutions of nuclear wastes. Octyl (phenyl)-N-N-diisobutyl-carbamoylmethylphosphine oxide (CMPO) is the active actinide complexant used in the TRUEX solvent. CMPO is combined with tributyl phosphate (TBP) in an organic diluent, typically n-dodecane, to form the TRUEX solvent. Small quantities of impurities in the CMPO resulting from: (1) synthesis, (2) acid hydrolysis, or (3) radiolysis can result in actinide stripping problems from the solvent. The impurity, octylphenylphosphinic acid (POPPA), ia a powerful extractant atmore » low acid concentrations which may be formed during CMPO synthesis. Consequently, commercial CMPO may contain sufficient quantities of POPPA to significantly impact the stripping of actinides from the TRUEX solvent. The purpose of these tests was to (1) determine if commercially available CMPO is sufficiently pure to alleviate actinide stripping problems from the TRUEX process and (2) to determine if solvent cleanup methods are sufficient to purify the commercially purchased CMPO. Extraction and solvent cleanup methodologies used by Horwitz and coworkers at ANL were used to determine CMPO purity with {sup 241}Am. The improvement of the americium distribution coefficient in dilute nitric acid resulting from further purifying this CMPO is not significant enough to warrant additional CMPO purifying steps. The commercially purchased CMPO is found to be acceptable to use, as received, in a full-scale TRUEX process.« less

  16. The Interaction of Spacecraft Cabin Atmospheric Quality and Water Processing System Performance

    NASA Technical Reports Server (NTRS)

    Perry, Jay L.; Croomes, Scott D. (Technical Monitor)

    2002-01-01

    Although designed to remove organic contaminants from a variety of waste water streams, the planned U.S.- and present Russian-provided water processing systems onboard the International Space Station (ISS) have capacity limits for some of the more common volatile cleaning solvents used for housekeeping purposes. Using large quantities of volatile cleaning solvents during the ground processing and in-flight operational phases of a crewed spacecraft such as the ISS can lead to significant challenges to the water processing systems. To understand the challenges facing the management of water processing capacity, the relationship between cabin atmospheric quality and humidity condensate loading is presented. This relationship is developed as a tool to determine the cabin atmospheric loading that may compromise water processing system performance. A comparison of cabin atmospheric loading with volatile cleaning solvents from ISS, Mir, and Shuttle are presented to predict acceptable limits to maintain optimal water processing system performance.

  17. Novel shortcut estimation method for regeneration energy of amine solvents in an absorption-based carbon capture process.

    PubMed

    Kim, Huiyong; Hwang, Sung June; Lee, Kwang Soon

    2015-02-03

    Among various CO2 capture processes, the aqueous amine-based absorption process is considered the most promising for near-term deployment. However, the performance evaluation of newly developed solvents still requires complex and time-consuming procedures, such as pilot plant tests or the development of a rigorous simulator. Absence of accurate and simple calculation methods for the energy performance at an early stage of process development has lengthened and increased expense of the development of economically feasible CO2 capture processes. In this paper, a novel but simple method to reliably calculate the regeneration energy in a standard amine-based carbon capture process is proposed. Careful examination of stripper behaviors and exploitation of energy balance equations around the stripper allowed for calculation of the regeneration energy using only vapor-liquid equilibrium and caloric data. Reliability of the proposed method was confirmed by comparing to rigorous simulations for two well-known solvents, monoethanolamine (MEA) and piperazine (PZ). The proposed method can predict the regeneration energy at various operating conditions with greater simplicity, greater speed, and higher accuracy than those proposed in previous studies. This enables faster and more precise screening of various solvents and faster optimization of process variables and can eventually accelerate the development of economically deployable CO2 capture processes.

  18. Development of a solvent processed insensitive propellant

    NASA Technical Reports Server (NTRS)

    Trask, R.; Costa, E.; Beardell, A. J.

    1980-01-01

    Two types of low vulnerability propellants are studied which are distinguished by whether the binder is a rubber, such as polyurethane or CTBN, or a plasticizable polymer such as ethyl cellulose or cellulose acetate. The former propellants are made by a partial cure extrusion process while the latter are made by the conventional solvent process. Emphasis is given to a cellulose binder (plasticizer) RDX composition. The type of binder used, the particle size of the RDX and the presence of small quantities of nitrocellulose in the solvent processed compositions have important influences on the mechanical and combustion characteristics of the propellant. The low temperature combustion is of particular concern because of potential breakup of the grains that can lead to instability.

  19. High Performance of Perovskite Solar Cells via Catalytic Treatment in Two-Step Process: The Case of Solvent Engineering.

    PubMed

    Li, Wenzhe; Fan, Jiandong; Li, Jiangwei; Niu, Guangda; Mai, Yaohua; Wang, Liduo

    2016-11-09

    Currently, the potential mechanism of the solvent-assisted crystallization for mixed cations perovskite thin film (FA x MA 1-x PbI 3 ) prepared via two-step solution-process still remains obscure. Here, we clarified the molecular-competing-reacted process of NH 2 CH═NH 2 I (FAI) and CH 3 NH 3 I (MAI) with PbI 2 (DMSO) x complex in dimethyl sulfoxide (DMSO) and diethyl ether (DE) catalytic solvent system in the sequential two-step solution-process. The microscopic dynamics was characterized via the characterizations of in situ photoluminescence spectra. In addition, we found that the thermal stability of the perovskite films suffered from the residual solvent with high boiling point, for example, DMSO. The further DE treatment could promote the volatility process of DMSO and accelerate the crystallization process of perovskite films. The highest PCE over 19% with slight hysteresis effect was eventually obtained with a reproducible FA 0.88 MA 0.12 PbI 3 solar cell, which displayed a constant power output within 100 s upon light soaking and stable PCE output within 30 d in the thermal stability test.

  20. Formula for the Removal and Remediation of Polychlorinated Biphenyls in Painted Structures

    NASA Technical Reports Server (NTRS)

    Quinn, Jacqueline; Loftin, Kathleen; Geiger, Cherie

    2010-01-01

    An activated metal treatment system (AMTS) removes and destroys polychlorinated biphenyls (PCBs) found in painted structures or within the binding or caulking material on structures. It may be applied using a "paint-on and wipe-off" process that leaves the structure PCB-free and virtually unaltered in physical form. AMTS is used in conjunction with a solvent solution capable of donating hydrogen atoms. AMTS as a treatment technology has two functions: first, to extract PCBs from the material, and second, to degrade the extracted PCBs. The process for removing PCBs from structures is accomplished as an independent step to the degradation process. The goal is to extract the PCBs out of the paint, without destroying the paint, and to partition the PCBs into an environmentally friendly solvent. The research to date indicates this can be accomplished within the first 24 hours of AMTS contact with the paint. PCBs are extremely hydrophobic and prefer to be in the AMTS over the hardened paint or binder material. The solvent selected must be used to open, but not to destroy, the paint s polymeric lattice structure, allowing pathways for PCB movement out of the paint and into the solvent. A number of solvent systems were tested and are available for use within the AMTS. The second process of the AMTS is the degradation or dehalogenation of the PCBs. The solvent selection for this process is limited to solvents that are capable of donating a hydrogen atom to the PCB structure. Additional AMTS formulation properties that must be addressed for each site-specific application include viscosity and stability. The AMTS must be thick enough to remain where it is applied. Several thickening agents have been tested. Adding a stabilizing agent ensures that the AMTS will not evaporate and leave unprotected, activated metal exposed. During AMTS formulation testing, a number of reagents were evaluated to ensure the rate of dehalogenation was not inhibited by its addition to the system.

  1. 77 FR 53192 - Environmental Management Site-Specific Advisory Board, Northern New Mexico

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-08-31

    ... Annual Self-Evaluation 2:30 p.m. Items from the DDFO, Ed Worth Update from DOE Other Items 2:45 p.m... Protection Agency (Region 6), Ed Worth for Rich Mayer Data Input and Validation and Verification Process 4:15...

  2. Laser surface melting of 10 wt% Mo alloyed hardfacing Stellite 12 plasma transferred arc deposits: Structural evolution and high temperature wear performance

    NASA Astrophysics Data System (ADS)

    Dilawary, Shaikh Asad Ali; Motallebzadeh, Amir; Afzal, Muhammad; Atar, Erdem; Cimenoglu, Huseyin

    2018-05-01

    Laser surface melting (LSM) process has been applied on the plasma transferred arc (PTA) deposited Stellite 12 and 10 wt% Mo alloyed Stellite 12 in this study. Following the LSM process, structural and mechanical property comparison of the LSM'ed surfaces has been made. Hardness of the LSM'ed surfaces was measured as 549 HV and 623 HV for the Stellite 12 and Stellite 12 + 10 wt% Mo deposits, respectively. Despite their different hardness and structural features, the LSM'ed surfaces exhibited similar tribological performance at room temperature (RT), where fatigue wear mechanism operates. However, the wear at 500 °C promotes tribo-oxide layer formation whose composition depended on the alloying with Mo. Thus, addition of 10 wt% Mo into Stellite 12 PTA deposit has remarkably enhanced the high temperature wear performance of the LSM'ed surface as a result of participation of complex oxide (CoMoO4) in tribo-oxide layer.

  3. Transfer of care and offload delay: continued resistance or integrative thinking?

    PubMed

    Schwartz, Brian

    2015-11-01

    The disciplines of paramedicine and emergency medicine have evolved synchronously over the past four decades, linked by emergency physicians with expertise in prehospital care. Ambulance offload delay (OD) is an inevitable consequence of emergency department overcrowding (EDOC) and compromises the care of the patient on the ambulance stretcher in the emergency department (ED), as well as paramedic emergency medical service response in the community. Efforts to define transfer of care from paramedics to ED staff with a view to reducing offload time have met with resistance from both sides with different agendas. These include the need to return paramedics to serve the community versus the lack of ED capacity to manage the patient. Innovative solutions to other system issues, such as rapid access to trauma teams, reducing door-to-needle time, and improving throughput in the ED to reduce EDOC, have been achieved by involving all stakeholders in an integrative thinking process. Only by addressing this issue in a similar integrative process will solutions to OD be realized.

  4. Slipstream pilot-scale demonstration of a novel amine-based post-combustion technology for carbon dioxide capture from coal-fired power plant flue gas

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Krishnamurthy, Krish R.

    Post-combustion CO 2 capture (PCC) technology offers flexibility to treat the flue gas from both existing and new coal-fired power plants and can be applied to treat all or a portion of the flue gas. Solvent-based technologies are today the leading option for PCC from commercial coal-fired power plants as they have been applied in large-scale in other applications. Linde and BASF have been working together to develop and further improve a PCC process incorporating BASF’s novel aqueous amine-based solvent technology. This technology offers significant benefits compared to other solvent-based processes as it aims to reduce the regeneration energy requirementsmore » using novel solvents that are very stable under the coal-fired power plant feed gas conditions. BASF has developed the desired solvent based on the evaluation of a large number of candidates. In addition, long-term small pilot-scale testing of the BASF solvent has been performed on a lignite-fired flue gas. In coordination with BASF, Linde has evaluated a number of options for capital cost reduction in large engineered systems for solvent-based PCC technology. This report provides a summary of the work performed and results from a project supported by the US DOE (DE-FE0007453) for the pilot-scale demonstration of a Linde-BASF PCC technology using coal-fired power plant flue gas at a 1-1.5 MWe scale in Wilsonville, AL at the National Carbon Capture Center (NCCC). Following a project kick-off meeting in November 2011 and the conclusion of pilot plant design and engineering in February 2013, mechanical completion of the pilot plant was achieved in July 2014, and final commissioning activities were completed to enable start-up of operations in January 2015. Parametric tests were performed from January to December 2015 to determine optimal test conditions and evaluate process performance over a variety of operation parameters. A long-duration 1500-hour continuous test campaign was performed from May to August 2016 at a selected process condition to evaluate process performance and solvent stability over a longer period similar to how the process would operate as a continuously running large-scale PCC plant. The pilot plant integrated a number of unique features of the Linde-BASF technology aimed at lowering overall energy consumption and capital costs. During the overall test period including startup, parametric testing and long-duration testing, the pilot plant was operated for a total of 6,764 hours out of which testing with flue gas was performed for 4,109 hours. The pilot plant testing demonstrated all of the performance targets including CO 2 capture rate exceeding 90%, CO 2 purity exceeding 99.9 mol% (dry), flue gas processing capacity up to 15,500 lbs/hr (equivalent to 1.5 MWe capacity slipstream), regeneration energy as low as 2.7 GJ/tonne CO 2, and regenerator operating pressure up to 3.4 bara. Excellent solvent stability performance data was measured and verified by Linde and BASF during both test campaigns. In addition to process data, significant operational learnings were gained from pilot tests that will contribute greatly to the commercial success of PCC. Based on a thorough techno-economic assessment (TEA) of the Linde-BASF PCC process integrated with a 550 MWe supercritical coal-fired power plant, the net efficiency of the integrated power plant with CO 2 capture is increased from 28.4% with the DOE/NETL Case 12 reference to 30.9% with the Linde-BASF PCC plant previously presented utilizing the BASF OASE® blue solvent [Ref. 4], and is further increased to 31.4% using a Linde-BASF PCC plant with BASF OASE® blue solvent and an advanced stripper interstage heater (SIH) configuration. The Linde-BASF PCC plant incorporating the BASF OASE® blue solvent also results in significantly lower overall capital costs, thereby reducing the cost of electricity (COE) and cost of CO 2 captured from $147.25/MWh and $56.49/MT CO 2, respectively, for the reference DOE/NETL Case 12 plant, to $128.49/MWh and $41.85/MT CO2 for process case LB1, respectively, and $126.65/MWh and $40.66/MT CO 2 for process case SIH, respectively. With additional innovative Linde-BASF PCC process configuration improvements, the COE and cost of CO 2 captured can be further reduced to $125.51/MWh and $39.90/MT CO 2 for a further optimized PCC process defined as LB1-CREB. Most notably, the Linde-BASF process options assessed have already demonstrated the potential to lower the cost of CO 2 captured below the DOE target of $40/MT CO 2 at the 550 MWe scale for second generation PCC technologies. Project organization, structure, goals, tasks, accomplishments, process criteria and milestones will be presented in this report along with highlights and key results from parametric and long-duration testing of the Linde-BASF PCC pilot. The parametric and long-duration testing campaigns were aimed at validating the performance of the PCC technology against targets determined from a preliminary techno-economic assessment. The stability of the solvent with extended operation in a realistic power plant setting was measured with performance verified. Additionally, general solvent classification information, process operating conditions, normalized solvent performance data, solvent stability test results, flue gas conditions data, CO 2 purity data in the gaseous product stream, steam requirements and process flow diagrams, and updated process economic data for a scaled-up 550 MWe supercritical power plant with CO 2 capture are presented and discussed in this report.« less

  5. A systematic review and meta-analysis of 'Systems for Social Processes' in eating disorders.

    PubMed

    Caglar-Nazali, H Pinar; Corfield, Freya; Cardi, Valentina; Ambwani, Suman; Leppanen, Jenni; Olabintan, Olaolu; Deriziotis, Stephanie; Hadjimichalis, Alexandra; Scognamiglio, Pasquale; Eshkevari, Ertimiss; Micali, Nadia; Treasure, Janet

    2014-05-01

    Social and emotional problems have been implicated in the development and maintenance of eating disorders (ED). This paper reviews the facets of social processing in ED according to the NIMH Research and Domain Criteria (NIMH RDoC) 'Systems for Social Processes' framework. Embase, Medline, PsycInfo and Web of Science were searched for peer-reviewed articles published by March 2013. One-hundred and fifty four studies measuring constructs of: attachment, social communication, perception and understanding of self and others, and social dominance in people with ED, were identified. Eleven meta-analyses were performed, they showed evidence that people with ED had attachment insecurity (d=1.31), perceived low parental care (d=.51), appraised high parental overprotection (d=0.29), impaired facial emotion recognition (d=.44) and facial communication (d=2.10), increased facial avoidance (d=.52), reduced agency (d=.39), negative self-evaluation (d=2.27), alexithymia (d=.66), poor understanding of mental states (d=1.07) and sensitivity to social dominance (d=1.08). There is less evidence for problems with production and reception of non-facial communication, animacy and action. Copyright © 2013 Elsevier Ltd. All rights reserved.

  6. Liquefaction of lignocellulosic biomass: solvent, process parameter, and recycle oil screening.

    PubMed

    van Rossum, Guus; Zhao, Wei; Castellvi Barnes, Maria; Lange, Jean-Paul; Kersten, Sascha R A

    2014-01-01

    The liquefaction of lignocellulosic biomass is studied for the production of liquid (transportation) fuels. The process concept uses a product recycle as a liquefaction medium and produces a bio-oil that can be co-processed in a conventional oil refinery. This all is done at medium temperature (≈ 300 °C) and pressure (≈ 60 bar). Solvent-screening experiments showed that oxygenated solvents are preferred as they allow high oil (up to 93% on carbon basis) and low solid yields (≈ 1-2% on carbon basis) and thereby outperform the liquefaction of biomass in compressed water and biomass pyrolysis. The following solvent ranking was obtained: guaiacol>hexanoic acid ≫ n-undecane. The use of wet biomass results in higher oil yields than dry biomass. However, it also results in a higher operating pressure, which would make the process more expensive. Refill experiments were also performed to evaluate the possibility to recycle the oil as the liquefaction medium. The recycled oil appeared to be very effective to liquefy the biomass and even surpassed the start-up solvent guaiacol, but became increasingly heavy and more viscous after each refill and eventually showed a molecular weight distribution that resembles that of refinery vacuum residue. Copyright © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  7. Morphological control in polymer solar cells using low-boiling-point solvent additives

    NASA Astrophysics Data System (ADS)

    Mahadevapuram, Rakesh C.

    In the global search for clean, renewable energy sources, organic photovoltaics (OPVs) have recently been given much attention. Popular modern-day OPVs are made from solution-processible, carbon-based polymers (e.g. the model poly(3-hexylthiophene) that are intimately blended with fullerene derivatives (e.g. [6,6]-phenyl-C71-butyric acid methyl ester) to form what is known as the dispersed bulk-heterojunction (BHJ). This BHJ architecture has produced some of the most efficient OPVs to date, with reports closing in on 10% power conversion efficiency. To push efficiencies further into double digits, many groups have identified the BHJ nanomorphology---that is, the phase separations and grain sizes within the polymer: fullerene composite---as a key aspect in need of control and improvement. As a result, many methods, including thermal annealing, slow-drying (solvent) annealing, vapor annealing, and solvent additives, have been developed and studied to promote BHJ self-organization. Processing organic photovoltaic (OPV) blend solutions with high-boiling-point solvent additives has recently been used for morphological control in BHJ OPV cells. Here we show that even low-boiling-point solvents can be effective additives. When P3HT:PCBM OPV cells were processed with a low-boiling-point solvent tetrahydrafuran as an additive in parent solvent o-dichlorobenzene, charge extraction increased leading to fill factors as high as 69.5%, without low work-function cathodes, electrode buffer layers or thermal treatment. This was attributed to PCBM demixing from P3HT domains and better vertical phase separation, as indicated by photoluminescence lifetimes, hole mobilities, and shunt leakage currents. Dependence on solvent parameters and applicability beyond P3HT system was also investigated.

  8. Cleanliness verification process at Martin Marietta Astronautics

    NASA Astrophysics Data System (ADS)

    King, Elizabeth A.; Giordano, Thomas J.

    1994-06-01

    The Montreal Protocol and the 1990 Clean Air Act Amendments mandate CFC-113, other chlorinated fluorocarbons (CFC's) and 1,1,1-Trichloroethane (TCA) be banned from production after December 31, 1995. In response to increasing pressures, the Air Force has formulated policy that prohibits purchase of these solvents for Air Force use after April 1, 1994. In response to the Air Force policy, Martin Marietta Astronautics is in the process of eliminating all CFC's and TCA from use at the Engineering Propulsion Laboratory (EPL), located on Air Force property PJKS. Gross and precision cleaning operations are currently performed on spacecraft components at EPL. The final step of the operation is a rinse with a solvent, typically CFC-113. This solvent is then analyzed for nonvolatile residue (NVR), particle count and total filterable solids (TFS) to determine cleanliness of the parts. The CFC-113 used in this process must be replaced in response to the above policies. Martin Marietta Astronautics, under contract to the Air Force, is currently evaluating and testing alternatives for a cleanliness verification solvent. Completion of test is scheduled for May, 1994. Evaluation of the alternative solvents follows a three step approach. This first is initial testing of solvents picked from literature searches and analysis. The second step is detailed testing of the top candidates from the initial test phase. The final step is implementation and validation of the chosen alternative(s). Testing will include contaminant removal, nonvolatile residue, material compatibility and propellant compatibility. Typical materials and contaminants will be tested with a wide range of solvents. Final results of the three steps will be presented as well as the implementation plan for solvent replacement.

  9. RECOVERY OF URANIUM BY AROMATIC DITHIOCARBAMATE COMPLEXING

    DOEpatents

    Neville, O.K.

    1959-08-11

    A selective complexing organic solvent extraction process is presented for the separation of uranium values from an aqueous nitric acid solution of neutron irradiated thorium. The process comprises contacting the solution with an organic aromatic dithiccarbamaie and recovering the resulting urancdithiccarbamate complex with an organic solvent such as ethyl acetate.

  10. KEY NON-PROCESS SOLVENT USES TARGETED AS POLLUTION PREVENTION OPPORTUNITIES

    EPA Science Inventory

    The paper discusses an EPA assessment of non-process solvent emissions from 15 industrial and commercial source categories in support of the Consumer and Commercial Products Report to Congress which was mandated in Section 183(e) of the Clean Air Act Amendments of 1990. hese prod...

  11. 40 CFR 63.2840 - What emission requirements must I meet?

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... National Emission Standards for Hazardous Air Pollutants: Solvent Extraction for Vegetable Oil Production... month. (e) Low-HAP solvent option. For all vegetable oil production processes subject to this subpart... paragraphs (e)(1) through (5) of this section. Your vegetable oil production process is not subject to the...

  12. 40 CFR 63.2840 - What emission requirements must I meet?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... National Emission Standards for Hazardous Air Pollutants: Solvent Extraction for Vegetable Oil Production... month. (e) Low-HAP solvent option. For all vegetable oil production processes subject to this subpart... paragraphs (e)(1) through (5) of this section. Your vegetable oil production process is not subject to the...

  13. Bench-Scale Silicone Process for Low-Cost CO{sub 2} Capture

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Vipperla, Ravikumar; Yee, Michael; Steele, Ray

    This report presents system and economic analysis for a carbon capture unit which uses an amino-silicone solvent for CO{sub 2} capture and sequestration (CCS) in a pulverized coal (PC) boiler. The amino-silicone solvent is based on GAP-1 with Tri-Ethylene Glycol (TEG) as a co-solvent. The report also shows results for a CCS unit based on a conventional approach using mono-ethanol amine (MEA). Models were developed for both processes and used to calculate mass and energy balances. Capital costs and energy penalty were calculated for both systems, as well as the increase in cost of electricity. The amino-silicone solvent based systemmore » demonstrates significant advantages compared to the MEA system.« less

  14. Lignocellulose Liquefaction to Biocrude: A Tutorial Review

    PubMed Central

    2018-01-01

    Abstract After 40 years of research and development, liquefaction technologies are now being demonstrated at 200–3000 tons per year scale to convert lignocellulosic biomass to biocrudes for use as heavy fuel or for upgrading to biofuels. This Review attempts to present the various facets of the liquefaction process in a tutorial manner. Emphasis is placed on liquefaction in high‐boiling solvents, with regular reference to liquefaction in subcritical water or other light‐boiling solvents. Reaction chemistry, solvent selection, role of optional catalyst as well as biocrude composition and properties are discussed in depth. Challenges in biomass feeding and options for biocrude–solvent separation are addressed. Process concepts are reviewed and demonstration/commercialization efforts are presented. PMID:29364569

  15. Reliable solution processed planar perovskite hybrid solar cells with large-area uniformity by chloroform soaking and spin rinsing induced surface precipitation

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Chern, Yann-Cherng; Wu, Hung-Ruei; Chen, Yen-Chu

    2015-08-15

    A solvent soaking and rinsing method, in which the solvent was allowed to soak all over the surface followed by a spinning for solvent draining, was found to produce perovskite layers with high uniformity on a centimeter scale and with much improved reliability. Besides the enhanced crystallinity and surface morphology due to the rinsing induced surface precipitation that constrains the grain growth underneath in the precursor films, large-area uniformity with film thickness determined exclusively by the rotational speed of rinsing spinning for solvent draining was observed. With chloroform as rinsing solvent, highly uniform and mirror-like perovskite layers of area asmore » large as 8 cm × 8 cm were produced and highly uniform planar perovskite solar cells with power conversion efficiency of 10.6 ± 0.2% as well as much prolonged lifetime were obtained. The high uniformity and reliability observed with this solvent soaking and rinsing method were ascribed to the low viscosity of chloroform as well as its feasibility of mixing with the solvent used in the precursor solution. Moreover, since the surface precipitation forms before the solvent draining, this solvent soaking and rinsing method may be adapted to spinless process and be compatible with large-area and continuous production. With the large-area uniformity and reliability for the resultant perovskite layers, this chloroform soaking and rinsing approach may thus be promising for the mass production and commercialization of large-area perovskite solar cells.« less

  16. Aqueous alternatives for metal and composite cleaning

    NASA Technical Reports Server (NTRS)

    Quitmeyer, Joann

    1994-01-01

    For many years the metalworking industry has cleaned metal and composite substrates with chlorinated solvents. Recently, however, health and disposal related environmental concerns have increased regarding chlorinated solvents, including 1,1,1-trichloroethane, trichloroethylene, methylene chloride, or Freon'. World leaders have instituted a production ban of certain ozone depleting chlorofluorocarbons (CFC's) by 1996. The Occupational Safety and Health Administration (OSHA) has instituted worker vapor exposure limitations for virtually all of the solvents used in solvent-based cleaners. In addition, the United States Environmental Protection Agency (EPA) has defined nearly all solvent-based cleaners as 'hazardous'. Cradle to grave waste responsibility is another reason manufacturers are trying to replace chlorinated solvents in their cleaning processes. Because of these factors, there now is a world wide effort to reduce and/or eliminate the use of chlorinated solvents for industrial cleaning. Waterbased cleaners are among the alternatives being offered to the industry. New technology alkaline cleaners are now available that can be used instead of chlorinated solvents in many cleaning processes. These waterbased cleaners reduce the release of volatile organic compounds (VOC's) by as much as 99 percent. (The definition and method of calculation of VOC's now varies from region to region.) Hazardous waste generation can also be significantly reduced or eliminated with new aqueous technology. This in turn can ease worker exposure restrictions and positively impact the environment. This paper compares the chemical and physical properties of this aqueous cleaners versus chlorinated solvents.

  17. Structure of catalase determined by MicroED

    PubMed Central

    Nannenga, Brent L; Shi, Dan; Hattne, Johan; Reyes, Francis E; Gonen, Tamir

    2014-01-01

    MicroED is a recently developed method that uses electron diffraction for structure determination from very small three-dimensional crystals of biological material. Previously we used a series of still diffraction patterns to determine the structure of lysozyme at 2.9 Å resolution with MicroED (Shi et al., 2013). Here we present the structure of bovine liver catalase determined from a single crystal at 3.2 Å resolution by MicroED. The data were collected by continuous rotation of the sample under constant exposure and were processed and refined using standard programs for X-ray crystallography. The ability of MicroED to determine the structure of bovine liver catalase, a protein that has long resisted atomic analysis by traditional electron crystallography, demonstrates the potential of this method for structure determination. DOI: http://dx.doi.org/10.7554/eLife.03600.001 PMID:25303172

  18. Acetone-butanol-ethanol (ABE) fermentation using Clostridium acetobutylicum XY16 and in situ recovery by PDMS/ceramic composite membrane.

    PubMed

    Wu, Hao; Chen, Xiao-Peng; Liu, Gong-Ping; Jiang, Min; Guo, Ting; Jin, Wan-Qin; Wei, Ping; Zhu, Da-Wei

    2012-09-01

    PDMS/ceramic composite membrane was directly integrated with acetone-butanol-ethanol (ABE) fermentation using Clostridium acetobutylicum XY16 at 37 °C and in situ removing ABE from fermentation broth. The membrane was integrated with batch fermentation, and approximately 46 % solvent was extracted. The solvent in permeates was 118 g/L, and solvent productivity was 0.303 g/(L/h), which was approximately 33 % higher compared with the batch fermentation without in situ recovery. The fed-batch fermentation with in situ recovery by pervaporation continued for more than 200 h, 61 % solvent was extracted, and the solvent in penetration was 96.2 g/L. The total flux ranged from 0.338 to 0.847 kg/(m(2)/h) and the separation factor of butanol ranged from 5.1 to 27.1 in this process. The membrane was fouled by the active fermentation broth, nevertheless the separation performances were partially recovered by offline membrane cleaning, and the solvent productivity was increased to 0.252 g/(L/h), which was 19 % higher compared with that in situ recovery process without membrane cleaning.

  19. PRODUCTION OF FLUOROCARBONS

    DOEpatents

    Sarsfield, N.F.

    1949-06-21

    This patent pertains to a process for recovering fluorocarbons from a liquid mixture of hydrocarbons with partially and completely fluorinated products thereof. It consists of contacting the mxture in the cold with a liquid which is a solvent for the hydrocarbons and which is a nonsolvent for the fluorocarbons, extracting the hydrocarbons, separating the fluorocarbon-containing layer from the solvent-containing layer, and submitting the fluorocarbon layer to fractlonal distillation, to isolate the desired fluorocarbon fraction. Suitable solvents wnich may be used in the process include the lower aliphatic alcohols, and the lower aliphatic ketones.

  20. Diagnostic overshadowing and other challenges involved in the diagnostic process of patients with mental illness who present in emergency departments with physical symptoms--a qualitative study.

    PubMed

    Shefer, Guy; Henderson, Claire; Howard, Louise M; Murray, Joanna; Thornicroft, Graham

    2014-01-01

    We conducted a qualitative study in the Emergency Departments (EDs) of four hospitals in order to investigate the perceived scope and causes of 'diagnostic overshadowing'--the misattribution of physical symptoms to mental illness--and other challenges involved in the diagnostic process of people with mental illness who present in EDs with physical symptoms. Eighteen doctors and twenty-one nurses working in EDs and psychiatric liaisons teams in four general hospitals in the UK were interviewed. Interviewees were asked about cases in which mental illness interfered with diagnosis of physical problems and about other aspects of the diagnostic process. Interviews were transcribed and analysed thematically. Interviewees reported various scenarios in which mental illness or factors related to it led to misdiagnosis or delayed treatment with various degrees of seriousness. Direct factors which may lead to misattribution in this regard are complex presentations or aspects related to poor communication or challenging behaviour of the patient. Background factors are the crowded nature of the ED environment, time pressures and targets and stigmatising attitudes held by a minority of staff. The existence of psychiatric liaison team covering the ED twenty-four hours a day, seven days a week, can help reduce the risk of misdiagnosis of people with mental illness who present with physical symptoms. However, procedures used by emergency and psychiatric liaison staff require fuller operationalization to reduce disagreement over where responsibilities lie.

  1. Developing a multidisciplinary approach within the ED towards domestic violence presentations.

    PubMed

    Basu, Subhashis; Ratcliffe, Giles

    2014-03-01

    To improve the detection and quality of care of patients who attend the emergency department (ED) with confirmed or suspected domestic abuse (DA). A quality improvement report on the design, implementation and evaluation of a specialised service and structured training programme to detect and manage DA presentations within an emergency medicine department. The study was set in the ED at the Northern General Hospital, Sheffield, UK. Key measures for improvement included introducing a service within the ED to help staff manage DA and coordinate responses; improve staff confidence in detecting DA; develop a structured and consistent process by which to manage DA presentations. An Independent Domestic Violence Advocate service was introduced into the department in July 2011 through a multiagency agreement. A structured training and education programme was delivered to ED staff. A 'communications form' was developed for DA risk assessment and case management. The process was reviewed quarterly. One hundred and seventy-two referrals were made to the service (121 distinct clients) over a 12-month period. Staff reported greater confidence in detecting DA, and community partners highlighted the role the service had in improving DA detection and care quality within the city. Strong leadership and prioritising the issue within the department has facilitated the development of the process and contributed substantially to its success. Support from community partners has been invaluable in tailoring the service and education programme to the needs of staff and patients within the department.

  2. Development of the Next-Generation Caustic-Side Solvent Extraction (NG-CSSX) Process for Cesium Removal from High-Level Tank Waste

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Moyer, Bruce A; Bonnesen, Peter V; Delmau, Laetitia Helene

    2011-01-01

    This paper describes the chemical performance of the Next-Generation Caustic-Side Solvent Extraction (NG-CSSX) process in its current state of development for removal of cesium from the alkaline high-level tank wastes at the Savannah River Site (SRS) in the US Department of Energy (USDOE) complex. Overall, motivation for seeking a major enhancement in performance for the currently deployed CSSX process stems from needs for accelerating the cleanup schedule and reducing the cost of salt-waste disposition. The primary target of the NG-CSSX development campaign in the past year has been to formulate a solvent system and to design a corresponding flowsheet thatmore » boosts the performance of the SRS Modular CSSX Unit (MCU) from a current minimum decontamination factor of 12 to 40,000. The chemical approach entails use of a more soluble calixarene-crown ether, called MaxCalix, allowing the attainment of much higher cesium distribution ratios (DCs) on extraction. Concurrently decreasing the Cs-7SB modifier concentration is anticipated to promote better hydraulics. A new stripping chemistry has been devised using a vitrification-friendly aqueous boric acid strip solution and a guanidine suppressor in the solvent, resulting in sharply decreased DCs on stripping. Results are reported herein on solvent phase behavior and batch Cs distribution for waste simulants and real waste together with a preliminary flowsheet applicable for implementation in the MCU. The new solvent will enable MCU to process a much wider range of salt feeds and thereby extend its service lifetime beyond its design life of three years. Other potential benefits of NG-CSSX include increased throughput of the SRS Salt Waste Processing Facility (SWPF), currently under construction, and an alternative modular near-tank application at Hanford.« less

  3. Thermoplastic composite matrices with improved solvent resistance

    NASA Technical Reports Server (NTRS)

    Hergenrother, P. M.; Jensen, B. J.; Havens, S. J.

    1984-01-01

    In order to improve solvent resistance of aromatic thermoplastic polymers, ethynyl-terminated aromatic sulfone polymers (ETS), sulfone/ester polymers (SEPE) containing pendent ethynyl groups, and phenoxy resin containing pendent ethynyl groups are synthesized. Cured polysulfones and phenoxy resins containing ethynyl groups on the ends or pendent on the molecules exhibited systematic behavior in solvent resistance, film flexibility, and toughness as a function of crosslink density. The film and composite properties of a cured solvent-resistant ETS were better than those of a commercially available solvent sensitive polysulfone. The study was part of a NASA program to better understand the trade-offs between solvent resistance, processability and mechanical properties which may be useful in designing composite structures for aerospace vehicles.

  4. Improving ED specimen TAT using Lean Six Sigma.

    PubMed

    Sanders, Janet H; Karr, Tedd

    2015-01-01

    Lean and Six Sigma are continuous improvement methodologies that have garnered international fame for improving manufacturing and service processes. Increasingly these methodologies are demonstrating their power to also improve healthcare processes. The purpose of this paper is to discuss a case study for the application of Lean and Six Sigma tools in the reduction of turnaround time (TAT) for Emergency Department (ED) specimens. This application of the scientific methodologies uncovered opportunities to improve the entire ED to lab system for the specimens. This case study provides details on the completion of a Lean Six Sigma project in a 1,000 bed tertiary care teaching hospital. Six Sigma's Define, Measure, Analyze, Improve, and Control methodology is very similar to good medical practice: first, relevant information is obtained and assembled; second, a careful and thorough diagnosis is completed; third, a treatment is proposed and implemented; and fourth, checks are made to determine if the treatment was effective. Lean's primary goal is to do more with less work and waste. The Lean methodology was used to identify and eliminate waste through rapid implementation of change. The initial focus of this project was the reduction of turn-around-times for ED specimens. However, the results led to better processes for both the internal and external customers of this and other processes. The project results included: a 50 percent decrease in vials used for testing, a 50 percent decrease in unused or extra specimens, a 90 percent decrease in ED specimens without orders, a 30 percent decrease in complete blood count analysis (CBCA) Median TAT, a 50 percent decrease in CBCA TAT Variation, a 10 percent decrease in Troponin TAT Variation, a 18.2 percent decrease in URPN TAT Variation, and a 2-5 minute decrease in ED registered nurses rainbow draw time. This case study demonstrated how the quantitative power of Six Sigma and the speed of Lean worked in harmony to improve the blood draw process for a 1,000 bed tertiary care teaching hospital. The blood draw process is a standard process used in hospitals to collect blood chemistry and hematology information for clinicians. The methods used in this case study demonstrated valuable and practical applications of process improvement methodologies that can be used for any hospital process and/or service environment. While this is not the first case study that has demonstrated the use of continuous process improvement methodologies to improve a hospital process, it is unique in the way in which it utilizes the strength of the project focussed approach that adheres more to the structure and rigor of Six Sigma and relied less on the speed of lean. Additionally, the application of these methodologies in healthcare is emerging research.

  5. Comparing Utilization and Costs of Care in Freestanding Emergency Departments, Hospital Emergency Departments, and Urgent Care Centers.

    PubMed

    Ho, Vivian; Metcalfe, Leanne; Dark, Cedric; Vu, Lan; Weber, Ellerie; Shelton, George; Underwood, Howard R

    2017-12-01

    We compare utilization, price per visit, and the types of care delivered across freestanding emergency departments (EDs), hospital-based EDs, and urgent care centers in Texas. We analyzed insurance claims processed by Blue Cross Blue Shield of Texas from 2012 to 2015 for patient visits to freestanding EDs, hospital-based EDs, or urgent care centers in 16 Texas metropolitan statistical areas containing 84.1% of the state's population. We calculated the aggregate number of visits, average price per visit, proportion of price attributable to facility and physician services, and proportion of price billed to Blue Cross Blue Shield of Texas versus out of pocket, by facility type. Prices for the top 20 diagnoses and procedures by facility type are compared. Texans use hospital-based EDs and urgent care centers much more than freestanding EDs, but freestanding ED utilization increased 236% between 2012 and 2015. The average price per visit was lower for freestanding EDs versus hospital-based EDs in 2012 ($1,431 versus $1,842), but prices in 2015 were comparable ($2,199 versus $2,259). Prices for urgent care centers were only $164 and $168 in 2012 and 2015. Out-of-pocket liability for consumers for all these facilities increased slightly from 2012 to 2015. There was 75% overlap in the 20 most common diagnoses at freestanding EDs versus urgent care centers and 60% overlap for hospital-based EDs and urgent care centers. However, prices for patients with the same diagnosis were on average almost 10 times higher at freestanding and hospital-based EDs relative to urgent care centers. Utilization of freestanding EDs is rapidly expanding in Texas. Higher prices at freestanding and hospital-based EDs relative to urgent care centers, despite substantial overlap in services delivered, imply potential inefficient use of emergency facilities. Copyright © 2017 American College of Emergency Physicians. Published by Elsevier Inc. All rights reserved.

  6. Pathways to the Future: Linking Environmental Scanning to Strategic Management.

    ERIC Educational Resources Information Center

    Mecca, Thomas V.; Morrison, James L.

    1988-01-01

    Describes an ED QUEST (Quick Environmental Scanning Technique) workshop demonstrating the links between an environmental scanning/forecasting process and formulation of institutional strategy. Explains ED QUEST's use in identifying and analyzing critical trends and events, and identifying the nature of the organization; developing alternative…

  7. Solvent and process for recovery of hydroxide from aqueous mixtures

    DOEpatents

    Moyer, Bruce A.; Chambliss, C. Kevin; Bonnesen, Peter V.; Keever, Tamara J.

    2001-01-01

    Hydroxide values and associated alkali metal may be recovered from alkaline aqueous solutions using classes of fluorinated alcohols in a water immiscible solvent. The alcohols are characterized by fluorine substituents which are proximal to the acidic alcohol protons and are located to adjust the acidity of the extractant and the solubility of the extractant in the solvent. A method for stripping the extractant and solvent to regenerate the extractant and purified aqueous hydroxide solution is described.

  8. Long-range single domain array of a 5 nm pattern of supramolecules via solvent annealing in a double-sandwich cell.

    PubMed

    Kwon, Kiok; Park, Kangho; Jung, Hee-Tae

    2018-05-10

    In nanotechnology and microelectronics research, the generation of an ultradense, single-grain nanostructure with a long-range lateral order is challenging. In this paper, we report upon a new solvent-annealing method using a double-sandwich confinement to promote the formation of a large-area, single-domain array (>0.3 × 0.3 mm2) of supramolecular cylinders with a small feature size (4.7 nm). The in situ GISAXS experiment result shows the ordering process during solvent evaporation. The diffusion of the solvent molecules led to the disassembly of the supramolecules confined between the top and bottom surfaces and their subsequent mobilization, thereby producing a highly ordered hexagonal array of supramolecular materials under the double-sandwich confinement upon solvent evaporation. In addition, two key factors were found to be crucial in this process for generating highly-ordered supramolecular building blocks: (i) the presence of a top coat during solvent evaporation to provide a geometric confinement template, and (ii) the control of the solvent evaporation rate during the solvent evaporation step to provide the dendrimer sufficient time to self-assemble into the highly ordered state over a large area. Our developed approach, which can be extended to be used for a large family of supramolecules, is of critical importance in providing a new bottom-up lithographic method based on supramolecular self-assembly.

  9. Fourier Transform Infrared Spectroscopy and Multivariate Analysis for Online Monitoring of Dibutyl Phosphate Degradation Product in Tributyl Phosphate/n-Dodecane/Nitric Acid Solvent

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Tatiana G. Levitskaia; James M. Peterson; Emily L. Campbell

    2013-12-01

    In liquid–liquid extraction separation processes, accumulation of organic solvent degradation products is detrimental to the process robustness, and frequent solvent analysis is warranted. Our research explores the feasibility of online monitoring of the organic solvents relevant to used nuclear fuel reprocessing. This paper describes the first phase of developing a system for monitoring the tributyl phosphate (TBP)/n-dodecane solvent commonly used to separate used nuclear fuel. In this investigation, the effect of extraction of nitric acid from aqueous solutions of variable concentrations on the quantification of TBP and its major degradation product dibutylphosphoric acid (HDBP) was assessed. Fourier transform infrared (FTIR)more » spectroscopy was used to discriminate between HDBP and TBP in the nitric acid-containing TBP/n-dodecane solvent. Multivariate analysis of the spectral data facilitated the development of regression models for HDBP and TBP quantification in real time, enabling online implementation of the monitoring system. The predictive regression models were validated using TBP/n-dodecane solvent samples subjected to high-dose external ?-irradiation. The predictive models were translated to flow conditions using a hollow fiber FTIR probe installed in a centrifugal contactor extraction apparatus, demonstrating the applicability of the FTIR technique coupled with multivariate analysis for the online monitoring of the organic solvent degradation products.« less

  10. Fourier Transform Infrared Spectroscopy and Multivariate Analysis for Online Monitoring of Dibutyl Phosphate Degradation Product in Tributyl Phosphate /n-Dodecane/Nitric Acid Solvent

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Levitskaia, Tatiana G.; Peterson, James M.; Campbell, Emily L.

    2013-11-05

    In liquid-liquid extraction separation processes, accumulation of organic solvent degradation products is detrimental to the process robustness and frequent solvent analysis is warranted. Our research explores feasibility of online monitoring of the organic solvents relevant to used nuclear fuel reprocessing. This paper describes the first phase of developing a system for monitoring the tributyl phosphate (TBP)/n-dodecane solvent commonly used to separate used nuclear fuel. In this investigation, the effect of extraction of nitric acid from aqueous solutions of variable concentrations on the quantification of TBP and its major degradation product dibutyl phosphoric acid (HDBP) was assessed. Fourier Transform Infrared Spectroscopymore » (FTIR) spectroscopy was used to discriminate between HDBP and TBP in the nitric acid-containing TBP/n-dodecane solvent. Multivariate analysis of the spectral data facilitated the development of regression models for HDBP and TBP quantification in real time, enabling online implementation of the monitoring system. The predictive regression models were validated using TBP/n-dodecane solvent samples subjected to the high dose external gamma irradiation. The predictive models were translated to flow conditions using a hollow fiber FTIR probe installed in a centrifugal contactor extraction apparatus demonstrating the applicability of the FTIR technique coupled with multivariate analysis for the online monitoring of the organic solvent degradation products.« less

  11. Engaging stakeholders to design a comparative effectiveness trial in children with uncontrolled asthma.

    PubMed

    Erwin, Kim; Martin, Molly A; Flippin, Tara; Norell, Sarah; Shadlyn, Ariana; Yang, Jie; Falco, Paula; Rivera, Jaime; Ignoffo, Stacy; Kumar, Rajesh; Margellos-Anast, Helen; McDermott, Michael; McMahon, Kate; Mosnaim, Giselle; Nyenhuis, Sharmilee M; Press, Valerie G; Ramsay, Jessica E; Soyemi, Kenneth; Thompson, Trevonne M; Krishnan, Jerry A

    2016-01-01

    To present the methods and outcomes of stakeholder engagement in the development of interventions for children presenting to the emergency department (ED) for uncontrolled asthma. We engaged stakeholders (caregivers, physicians, nurses, administrators) from six EDs in a three-phase process to: define design requirements; prototype and refine; and evaluate. Interviews among 28 stakeholders yielded themes regarding in-home asthma management practices and ED discharge experiences. Quantitative and qualitative evaluation showed strong preference for the new discharge tool over current tools. Engaging end-users in contextual inquiry resulted in CAPE (CHICAGO Action Plan after ED discharge), a new stakeholder-balanced discharge tool, which is being tested in a multicenter comparative effectiveness trial.

  12. Organic electronic devices with multiple solution-processed layers

    DOEpatents

    Forrest, Stephen R.; Lassiter, Brian E.; Zimmerman, Jeramy D.

    2015-08-04

    A method of fabricating a tandem organic photosensitive device involves depositing a first layer of an organic electron donor type material film by solution-processing of the organic electron donor type material dissolved in a first solvent; depositing a first layer of an organic electron acceptor type material over the first layer of the organic electron donor type material film by a dry deposition process; depositing a conductive layer over the interim stack by a dry deposition process; depositing a second layer of the organic electron donor type material over the conductive layer by solution-processing of the organic electron donor type material dissolved in a second solvent, wherein the organic electron acceptor type material and the conductive layer are insoluble in the second solvent; depositing a second layer of an organic electron acceptor type material over the second layer of the organic electron donor type material film by a dry deposition process, resulting in a stack.

  13. Nefopam hydrochloride loaded microspheres for post-operative pain management: synthesis, physicochemical characterization and in-vivo evaluation.

    PubMed

    Sharma, Neelam; Arora, Sandeep; Madan, Jitender

    2018-02-01

    Once-daily oral dosage of nefopam hydrochloride loaded sustained release microspheres (NPH-MS) was investigated as novel therapeutic strategy for post-operative pain management. Microspheres were synthesized using poly-3-hydroxybutyrate and poly-(ɛ-caprolactone) by double emulsion solvent evaporation technique. NPH-MS were characterized through FTIR, PXRD and SEM. In-vitro drug release study revealed sustained behavior till 24 h. Haemolysis was <5% which signified haemocompatibility of formulation. ED50 in rat tail-flick anti-nociceptive test was found ∼18.12 mg/kg. In post-operative pain model, reversal of mechanical allodynia and thermal hyperalgesia by NPH-MS was statistically significant (p < .001) as compared with NPH till 24 h post-dose.

  14. Quality assurance in transnational higher education: a case study of the tropEd network

    PubMed Central

    2013-01-01

    Introduction Transnational or cross-border higher education has rapidly expanded since the 1980s. Together with that expansion issues on quality assurance came to the forefront. This article aims to identify key issues regarding quality assurance of transnational higher education and discusses the quality assurance of the tropEd Network for International Health in Higher Education in relation to these key issues. Methods Literature review and review of documents. Results From the literature the following key issues regarding transnational quality assurance were identified and explored: comparability of quality assurance frameworks, true collaboration versus erosion of national education sovereignty, accreditation agencies and transparency. The tropEd network developed a transnational quality assurance framework for the network. The network accredits modules through a rigorous process which has been accepted by major stakeholders. This process was a participatory learning process and at the same time the process worked positive for the relations between the institutions. Discussion The development of the quality assurance framework and the process provides a potential example for others. PMID:23537108

  15. Controlling Actinide Hydration in Mixed Solvent Systems: Towards Tunable Solvent Systems to Close the Fuel Cycle

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Clark, Sue B.

    2016-10-31

    The goal of this project has been to define the extent of hydration the f-elements and other cations in mixed solvent electrolyte systems. Methanol-water and other mixed solvent systems have been studied, where the solvent dielectric constant was varied systematically. Thermodynamic and spectroscopic studies provide details concerning the energetics of complexation and other reactions of these cations. This information has also been used to advance new understanding of the behavior of these cations in a variety of systems, ranging from environmental studies, chromatographic approaches, and ionization processes for mass spectrometry.

  16. Development of Solvent Extraction Approach to Recycle Enriched Molybdenum Material

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Tkac, Peter; Brown, M. Alex; Sen, Sujat

    2016-06-01

    Argonne National Laboratory, in cooperation with Oak Ridge National Laboratory and NorthStar Medical Technologies, LLC, is developing a recycling process for a solution containing valuable Mo-100 or Mo-98 enriched material. Previously, Argonne had developed a recycle process using a precipitation technique. However, this process is labor intensive and can lead to production of large volumes of highly corrosive waste. This report discusses an alternative process to recover enriched Mo in the form of ammonium heptamolybdate by using solvent extraction. Small-scale experiments determined the optimal conditions for effective extraction of high Mo concentrations. Methods were developed for removal of ammonium chloridemore » from the molybdenum product of the solvent extraction process. In large-scale experiments, very good purification from potassium and other elements was observed with very high recovery yields (~98%).« less

  17. Brain response to images of food varying in energy density is associated with body composition in 7- to 10-year-old children: Results of an exploratory study.

    PubMed

    Fearnbach, S Nicole; English, Laural K; Lasschuijt, Marlou; Wilson, Stephen J; Savage, Jennifer S; Fisher, Jennifer O; Rolls, Barbara J; Keller, Kathleen L

    2016-08-01

    Energy balance is regulated by a multifaceted system of physiological signals that influence energy intake and expenditure. Therefore, variability in the brain's response to food may be partially explained by differences in levels of metabolically active tissues throughout the body, including fat-free mass (FFM) and fat mass (FM). The purpose of this study was to test the hypothesis that children's body composition would be related to their brain response to food images varying in energy density (ED), a measure of energy content per weight of food. Functional magnetic resonance imaging (fMRI) was used to measure brain response to High (>1.5kcal/g) and Low (<1.5kcal/g) ED food images, and Control images, in 36 children ages 7-10years. Body composition was measured using bioelectrical impedance analysis. Multi-subject random effects general linear model (GLM) and two-factor repeated measures analysis of variance (ANOVA) were used to test for main effects of ED (High ED vs. Low ED) in a priori defined brain regions of interest previously implicated in energy homeostasis and reward processing. Pearson's correlations were then calculated between activation in these regions for various contrasts (High ED-Low ED, High ED-Control, Low ED-Control) and child body composition (FFM index, FM index, % body fat). Relative to Low ED foods, High ED foods elicited greater BOLD activation in the left thalamus. In the right substantia nigra, BOLD activation for the contrast of High ED-Low ED foods was positively associated with child FFM. There were no significant results for the High ED-Control or Low ED-Control contrasts. Our findings support literature on FFM as an appetitive driver, such that greater amounts of lean mass were associated with greater activation for High ED foods in an area of the brain associated with dopamine signaling and reward (substantia nigra). These results confirm our hypothesis that brain response to foods varying in energy content is related to measures of child body composition. Copyright © 2016 Elsevier Inc. All rights reserved.

  18. Sustained reductions in time to antibiotic delivery in febrile immunocompromised children: results of a quality improvement collaborative.

    PubMed

    Dandoy, Christopher E; Hariharan, Selena; Weiss, Brian; Demmel, Kathy; Timm, Nathan; Chiarenzelli, Janis; Dewald, Mary Katherine; Kennebeck, Stephanie; Langworthy, Shawna; Pomales, Jennifer; Rineair, Sylvia; Sandfoss, Erin; Volz-Noe, Pamela; Nagarajan, Rajaram; Alessandrini, Evaline

    2016-02-01

    Timely delivery of antibiotics to febrile immunocompromised (F&I) paediatric patients in the emergency department (ED) and outpatient clinic reduces morbidity and mortality. The aim of this quality improvement initiative was to increase the percentage of F&I patients who received antibiotics within goal in the clinic and ED from 25% to 90%. Using the Model of Improvement, we performed Plan-Do-Study-Act cycles to design, test and implement high-reliability interventions to decrease time to antibiotics. Pre-arrival interventions were tested and implemented, followed by post-arrival interventions in the ED. Many processes were spread successfully to the outpatient clinic. The Chronic Care Model was used, in addition to active family engagement, to inform and improve processes. The study period was from January 2010 to January 2015. Pre-arrival planning improved our F&I time to antibiotics in the ED from 137 to 88 min. This was sustained until October 2012, when further interventions including a pre-arrival huddle decreased the median time to <50 min. Implementation of the various processes to the clinic delivery system increased the mean percentage of patients receiving antibiotics within 60 min to >90%. In September 2014, we implemented a rapid response team to improve reliable venous access in the ED, which increased our mean percentage of patients receiving timely antibiotics to its highest rate (95%). This stepwise approach with pre-arrival planning using the Chronic Care Model, followed by standardisation of processes, created a sustainable improvement of timely antibiotic delivery in F&I patients. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

  19. Microencapsulation Processes

    NASA Astrophysics Data System (ADS)

    Whateley, T. L.; Poncelet, D.

    2005-06-01

    Microencapsulation by solvent evaporation is a novel technique to enable the controlled delivery of active materials.The controlled release of drugs, for example, is a key challenge in the pharmaceutical industries. Although proposed several decades ago, it remains largely an empirical laboratory process.The Topical Team has considered its critical points and the work required to produce a more effective technology - better control of the process for industrial production, understanding of the interfacial dynamics, determination of the solvent evaporation profile, and establishment of the relation between polymer/microcapsule structures.The Team has also defined how microgravity experiments could help in better understanding microencapsulation by solvent evaporation, and it has proposed a strategy for a collaborative project on the topic.

  20. Impact of quality parameters on the recovery of putrescine and cadaverine in fish using methanol-hydrochloric acid solvent extraction.

    PubMed

    Richard, Nicole L; Pivarnik, Lori F; Ellis, P Christopher; Lee, Chong M

    2011-01-01

    Methanol (MeOH) extraction by AOAC Official Method 996.07 has resulted in low amine recoveries in fresh fish tissue. Addition of 25% 0.4 M HCl to the 75% methanol-water extraction solvent resulted in higher recoveries of putrescine and cadaverine. Average putrescine recovery increased from 55 to 92% in flounder, scup, bluefish, and salmon; from 92 to 98% in mackerel; and from 83 to 107% in processed mackerel. Average cadaverine recovery increased from 57 to 95% in flounder, scup, bluefish, and salmon; from 91 to 97% in mackerel; and from 92 to 108% in processed mackerel. Fish stored on ice for 12 days also showed differences between background concentrations determined with the two solvents. However, the values decreased with storage time, indicating that degradation of the protein matrix may cause more comparable measurements between the two solvents. However, consistently higher putrescine and cadaverine measurements were determined using MeOH-HCl. Although significant differences in the extraction of amines from the high-fat fish tissue were not seen between MeOH and MeOH-HCl, it would be ideal to have one solvent for biogenic amine extraction. This study confirms that MeOH-HCl is a better solvent for complete extraction and recovery of putrescine and cadaverine in fresh and processed fish tissues.

  1. Modifier mass transfer kinetic effect in the performance of solvent gradient simulated moving bed (SG-SMB) process

    NASA Astrophysics Data System (ADS)

    Câmara, L. D. T.

    2015-09-01

    The solvent-gradient simulated moving bed process (SG-SMB) is the new tendency in the performance improvement if compared to the traditional isocratic solvent conditions. In such SG-SMB separation process the modulation of the solvent strength leads to significant increase in the purities and productivity followed by reduction in the solvent consumption. A stepwise modelling approach was utilized in the representation of the interconnected chromatographic columns of the system combined with lumped mass transfer models between the solid and liquid phase. The influence of the solvent modifier was considered applying the Abel model which takes into account the effect of modifier volume fraction over the partition coefficient. The modelling and simulations were carried out and compared to the experimental SG-SMB separation of the amino acids phenylalanine and tryptophan. A lumped mass transfer kinetic model was applied for both the modifier (ethanol) as well as the solutes. The simulation results showed that such simple and global mass transfer models are enough to represent all the mass transfer effect between the solid adsorbent and the liquid phase. The separation performance can be improved reducing the interaction or the mass transfer kinetic effect between the solid adsorbent phase and the modifier. The simulations showed great agreement fitting the experimental data of the amino acids concentrations both at the extract as well as at the raffinate.

  2. Direct experience while eating: Laboratory outcomes among individuals with eating disorders versus healthy controls.

    PubMed

    Elices, Matilde; Carmona, Cristina; Narváez, Vanessa; Seto, Victoria; Martin-Blanco, Ana; Pascual, Juan C; Soriano, José; Soler, Joaquim

    2017-12-01

    To compare individuals with eating disorders (EDs) to healthy controls (HCs) to assess for differences in direct engagement in the eating process. Participants (n=58) were asked to eat an orange slice. To assess the degree of direct engagement with the eating process, participants were asked to write down 10 thoughts about the experience of eating the orange slice. Next, the participants were instructed to classify the main focus of each thought as either experiential ("direct experience") or analytical ("thinking about"). A direct experience index (DEI) was computed by dividing the number of times that participants classified an experience as a "direct experience" (the numerator) by the total number of all observations (i.e., direct experience+thinking about). Participants also completed the Five Facet Mindfulness Questionnaire (FFMQ) and the Experiences Questionnaire (EQ) to assess mindfulness facets and decentering, respectively. Compared to controls, participants in the EDs group presented significantly lower levels of direct experience during the eating task (EDs group: mean=43.54, SD=29.64; HCs group: mean=66.17, SD=22.23, p=0.03). Participants in the EDs group also scored significantly lower on other mindfulness-related variables. These findings suggest that engagement with the direct experience of eating is lower in individuals with EDs. Future research should investigate the role of mindfulness-based interventions to address direct experience while eating in individuals with EDs. Copyright © 2017 Elsevier Ltd. All rights reserved.

  3. Moving Average Models with Bivariate Exponential and Geometric Distributions.

    DTIC Science & Technology

    1985-03-01

    ordinary time series and of point processes. Developments in Statistics, Vol. 1, P.R. Krishnaiah , ed. Academic Press, New York. [9] Esary, J.D. and...valued and discrete - valued time series with ARMA correlation structure. Multivariate Analysis V, P.R. Krishnaiah , ed. North-Holland. 151-166. [28

  4. Determination of Factors Affecting Performance and Productivity in an Engineering/Design Environment

    DTIC Science & Technology

    1984-03-01

    Ivancevich & Donnelly, 1982, p. 82) Each of these theories conclude that how employees are motivated and what motivates employees will directly...Process (5th ed.). University of Washingto Houghton Mifflin Company. Gibson, J. L., Ivancevich , J. M., & Don, ,y, J. H. (1982). Organizations (4th ed

  5. Assessment of metal pollution sources by SEM/EDS analysis of solid particles in snow: a case study of Žerjav, Slovenia.

    PubMed

    Miler, Miloš; Gosar, Mateja

    2013-12-01

    Solid particles in snow deposits, sampled in mining and Pb-processing area of Žerjav, Slovenia, have been investigated using scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDS). Identified particles were classified as geogenic-anthropogenic, anthropogenic, and secondary weathering products. Geogenic-anthropogenic particles were represented by scarce Zn- and Pb-bearing ore minerals, originating from mine waste deposit. The most important anthropogenic metal-bearing particles in snow were Pb-, Sb- and Sn-bearing oxides and sulphides. The morphology of these particles showed that they formed at temperatures above their melting points. They were most abundant in snow sampled closest to the Pb-processing plant and least abundant in snow taken farthest from the plant, thus indicating that Pb processing was their predominant source between the last snowfall and the time of sampling. SEM/EDS analysis showed that Sb and Sn contents in these anthropogenic phases were higher and more variable than in natural Pb-bearing ore minerals. The most important secondary weathering products were Pb- and Zn-containing Fe-oxy-hydroxides whose elemental composition and morphology indicated that they mostly resulted from oxidation of metal-bearing sulphides emitted from the Pb-processing plant. This study demonstrated the importance of single particle analysis using SEM/EDS for differentiation between various sources of metals in the environment.

  6. Microencapsulation by solvent extraction/evaporation: reviewing the state of the art of microsphere preparation process technology.

    PubMed

    Freitas, Sergio; Merkle, Hans P; Gander, Bruno

    2005-02-02

    The therapeutic benefit of microencapsulated drugs and vaccines brought forth the need to prepare such particles in larger quantities and in sufficient quality suitable for clinical trials and commercialisation. Very commonly, microencapsulation processes are based on the principle of so-called "solvent extraction/evaporation". While initial lab-scale experiments are frequently performed in simple beaker/stirrer setups, clinical trials and market introduction require more sophisticated technologies, allowing for economic, robust, well-controllable and aseptic production of microspheres. To this aim, various technologies have been examined for microsphere preparation, among them are static mixing, extrusion through needles, membranes and microfabricated microchannel devices, dripping using electrostatic forces and ultrasonic jet excitation. This article reviews the current state of the art in solvent extraction/evaporation-based microencapsulation technologies. Its focus is on process-related aspects, as described in the scientific and patent literature. Our findings will be outlined according to the four major substeps of microsphere preparation by solvent extraction/evaporation, namely, (i) incorporation of the bioactive compound, (ii) formation of the microdroplets, (iii) solvent removal and (iv) harvesting and drying the particles. Both, well-established and more advanced technologies will be reviewed.

  7. Process for producing fluid fuel from coal

    DOEpatents

    Hyde, Richard W.; Reber, Stephen A.; Schutte, August H.; Nadkarni, Ravindra M.

    1977-01-01

    Process for producing fluid fuel from coal. Moisture-free coal in particulate form is slurried with a hydrogen-donor solvent and the heated slurry is charged into a drum wherein the pressure is so regulated as to maintain a portion of the solvent in liquid form. During extraction of the hydrocarbons from the coal, additional solvent is added to agitate the drum mass and keep it up to temperature. Subsequently, the pressure is released to vaporize the solvent and at least a portion of the hydrocarbons extracted. The temperature of the mass in the drum is then raised under conditions required to crack the hydrocarbons in the drum and to produce, after subsequent stripping, a solid coke residue. The hydrocarbon products are removed and fractionated into several cuts, one of which is hydrotreated to form the required hydrogen-donor solvent while other fractions can be hydrotreated or hydrocracked to produce a synthetic crude product. The heaviest fraction can be used to produce ash-free coke especially adapted for hydrogen manufacture. The process can be made self-sufficient in hydrogen and furnishes as a by-product a solid carbonaceous material with a useful heating value.

  8. Surfactant/Supercritical Fluid Cleaning of Contaminated Substrates

    NASA Technical Reports Server (NTRS)

    White, Gary L.

    1997-01-01

    CFC's and halogenated hydrocarbon solvents have been the solvents of choice to degrease and otherwise clean precision metal parts to allow proper function. Recent regulations have, however, rendered most of these solvents unacceptable for these purposes. New processes which are being used or which have been proposed to replace these solvents usually either fail to remove water soluble contaminants or produce significant aqueous wastes which must then be disposed of. In this work, a new method for cleaning surfaces will be investigated. Solubility of typical contaminants such as lubricating greases and phosphatizing bath residues will be studied in several surfactant/supercritical fluid solutions. The effect of temperature, pressure, and the composition of the cleaning mixture on the solubility of oily, polar, and ionic contaminants will be investigated. A reverse micellar solution in a supercritical light hydrocarbon solvent will be used to clean samples of industrial wastes. A reverse micellar solution is one where water is dissolved into a non-polar solvent with the aid of a surfactant. The solution will be capable of dissolving both water-soluble contaminants and oil soluble contaminants. Once the contaminants have been dissolved into the solution they will be separated from the light hydrocarbon and precipitated by a relatively small pressure drop and the supercritical solvent will be available for recycle for reuse. The process will be compared to the efficacy of supercritical CO2 cleaning by attempting to clean the same types of substrates and machining wastes with the same contaminants using supercritical CO2. It is anticipated that the supercritical CO2 process will not be capable of removing ionic residues.

  9. Catalytic coal liquefaction process

    DOEpatents

    Garg, D.; Sunder, S.

    1986-12-02

    An improved process for catalytic solvent refining or hydroliquefaction of non-anthracitic coal at elevated temperatures under hydrogen pressure in a solvent comprises using as catalyst a mixture of a 1,2- or 1,4-quinone and an alkaline compound, selected from ammonium, alkali metal, and alkaline earth metal oxides, hydroxides or salts of weak acids. 1 fig.

  10. Catalytic coal liquefaction process

    DOEpatents

    Garg, Diwakar; Sunder, Swaminathan

    1986-01-01

    An improved process for catalytic solvent refining or hydroliquefaction of non-anthracitic coal at elevated temperatures under hydrogen pressure in a solvent comprises using as catalyst a mixture of a 1,2- or 1,4-quinone and an alkaline compound, selected from ammonium, alkali metal, and alkaline earth metal oxides, hydroxides or salts of weak acids.

  11. SOLVENT EXTRACTION OF URANIUM VALUES

    DOEpatents

    Feder, H.M.; Ader, M.; Ross, L.E.

    1959-02-01

    A process is presented for extracting uranium salt from aqueous acidic solutions by organic solvent extraction. It consists in contacting the uranium bearing solution with a water immiscible dialkylacetamide having at least 8 carbon atoms in the molecule. Mentioned as a preferred extractant is dibutylacetamide. The organic solvent is usually used with a diluent such as kerosene or CCl/sub 4/.

  12. Operation of the solvent-refined-coal pilot plant, Wilsonville, Alabama. Annual technical report, January-December 1980

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Lewis, H.E.

    1981-08-01

    The plant was in operation for the equivalent of 247 days, an on-stream factor of 67.7%. Kentucky 9 coals from the Lafayette, Dotiki and Fies mines were processed. During 1980, the operating conditions and equipment were adjusted to evaluate potential process improvements. These experiments produced significant results in the following areas: Operating V103 High Pressure Separator in the hot mode; varying T102 Vacuum Column operating temperature; adding light SRC (LSRC), a product of the third stage of the Critical Solvent Deashing (CSD) unit, to the process solvent; investigating the effects of the chlorine content of the feed coal on corrosionmore » in the process vessels; evaluating the effects of adding sodium carbonate on corrosion rates; operating under conditions of low severity; i.e., low reactor temperature and long residence time; and testing an alternate CSD deashing solvent. A series of simulation runs investigating the design operating conditions for a planned 6000 ton per day SRC-I demonstation plant were also completed. Numerous improvements were made in the CSD processing area, and the components for a hydrotreating unit were installed.« less

  13. Influence of Solvent on the Drug-Loading Process of Amphiphilic Nanogel Star Polymers.

    PubMed

    Carr, Amber C; Piunova, Victoria A; Maarof, Hasmerya; Rice, Julia E; Swope, William C

    2018-05-31

    We present an all-atom molecular dynamics study of the effect of a range of organic solvents (dichloromethane, diethyl ether, toluene, methanol, dimethyl sulfoxide, and tetrahydrofuran) on the conformations of a nanogel star polymeric nanoparticle with solvophobic and solvophilic structural elements. These nanoparticles are of particular interest for drug delivery applications. As drug loading generally takes place in an organic solvent, this work serves to provide insight into the factors controlling the early steps of that process. Our work suggests that nanoparticle conformational structure is highly sensitive to the choice of solvent, providing avenues for further study as well as predictions for both computational and experimental explorations of the drug-loading process. Our findings suggest that when used in the drug-loading process, dichloromethane, tetrahydrofuran, and toluene allow for a more extensive and increased drug-loading into the interior of nanogel star polymers of the composition studied here. In contrast, methanol is more likely to support shallow or surface loading and, consequently, faster drug release rates. Finally, diethyl ether should not work in a formulation process since none of the regions of the nanogel star polymer appear to be sufficiently solvated by it.

  14. Experiment on the treatment of waste extraction solvent from the molybdenum-99 process

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Hsien-Ming Hsiao; Chang-Liang Hu; Kuang-Li Chien

    2013-07-01

    In the Mo-99 (Molybdenum-99) isotope extraction test process for radiopharmaceutical applications, organic solvent is used to extract Mo-99 from an irradiated UO{sub 2} dissolution. The extraction solvent was stored when the test work was stopped. A total of about 120 liters of waste solvent was stored at INER (Institute of Nuclear Energy Research, Taiwan). The extraction solvent consisted of 5% di-(2-ethylhexyl)-phosphoric acid (D2EHPA) and kerosene. The radionuclides found in the waste solvent include Cs-137, Am-241, Tc-99, and Sr-90, which give off gross alpha and beta radioactivity of 1898 and 471 Bq/ml, respectively. This study aims to remove radionuclides from themore » waste solvent using sodium carbonate and sodium hydroxide solutions in different concentrations. After mixing the waste solvent with the alkaline solution followed by settling, a third phase other than organic and aqueous phase appeared which is expected due to the saponification reaction. The experimental results showed that increasing the number of washing and the alkaline solution concentration could enhance the radionuclides removal rate. An optimal removal method was proposed using 2 M Na{sub 2}CO{sub 3} solution twice followed by 1 M NaOH solution one time for the third phase generated early in the mixing stages. The remaining gross alpha and beta radioactivity of the treated organic solvent was 2 and 3 Bq/ml, respectively. The treated solvent could be stabilized by ashing at 500 deg. C and then immobilized. The alkaline solution would be neutralized by hydrochloric or nitric acid and then treated using a variety of adsorbents or bone char via adsorption to remove nuclides to meet the wastewater discharge limitation. (authors)« less

  15. Adsorption Characteristics of Bixin on Acid- and Alkali-Treated Kaolinite in Aprotic Solvents

    PubMed Central

    Rahmalia, Winda; Fabre, Jean-François; Usman, Thamrin

    2018-01-01

    The adsorption of bixin in aprotic solvents onto acid- and alkali-treated kaolinite was investigated. Kaolinite was treated three times, for 6 h each, with 8 M HCl or 5 M KOH. The adsorbents were characterized by XRD, FT-IR, EDS, and BET-N2. The effects of contact time and dye concentration on adsorption capacity and kinetics, electronic transition of bixin before and after adsorption, and also mechanism of bixin-kaolinite adsorption were investigated. Dye adsorption followed pseudo-second order kinetics and was faster in acetone than in dimethyl carbonate. The best adsorption results were obtained for KOH-treated kaolinite. In both of the solvents, the adsorption isotherm followed the Langmuir model and adsorption capacity was higher in dimethyl carbonate (q m = 0.43 mg/g) than in acetone (0.29 mg/g). The adsorption capacity and kinetics of KOH-treated kaolinite (q m = 0.43 mg/g, k 2 = 3.27 g/mg·min) were better than those of HCl-treated kaolinite (q m = 0.21 mg/g, k 2 = 0.25 g/mg·min) and natural kaolinite (q m = 0.18 mg/g, k 2 = 0.32 g/mg·min). There are shift in the band position of maximum intensity of bixin after adsorption on this adsorbent. Adsorption in this system seemed to be based essentially on chemisorption due to the electrostatic interaction of bixin with the strong basic and reducing sites of kaolinite. PMID:29581720

  16. Co(II)-doped MOF-5 nano/microcrystals: Solvatochromic behaviour, sensing solvent molecules and gas sorption property

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Yang, Ji-Min; School of Chemistry and Chemical Engineering, Linyi University, Linyi 276005; Liu, Qing

    2014-10-15

    Co(II)-doped MOF-5 nano/microcrystals with controllable morphology and size were successfully obtained by solvothermal method. The products were characterized by powder X-ray diffraction (PXRD), energy dispersive spectrometry (EDS), field emission scanning electron microscopy (FESEM), thermogravimetric analysis (TGA), inductively coupled plasma optical emission spectrometer (ICP-OES), elemental analysis, UV–vis and infrared (IR) spectroscopy. The factors influencing the crystal morphology and size were investigated. The gas sorption measurements reveal that highly crystalline particles have large Langmuir surface area. It was found that the Co(II)-doped MOF-5 shows enhanced hydrostability and the sorption profiles of the Co(II)-doped MOF-5 nano/microcrystals are dependent on the morphology and sizemore » of the particles. Porous Co(II)-doped MOF-5 is stable upon the removal of guest molecules and exhibits different colour with accommodating different solvent molecule, which means that it can act as solvatochromic sensing materials for recognition of solvent molecules. - Graphical abstract: Co(II)-doped MOF-5 nano/microcrystals with different shapes and sizes were synthesized by a facile hydrothermal method, which not only enhance gas sorption properties and structural stability of MOFs towards moisture, but also act as new sensing materials for sensing small molecules. - Highlights: • Co(II)-doped MOF-5 nano/microcrystals with controllable morphology and size were obtained. • Co(II)-doped MOF-5 nano/microcrystals enhance the structural stability towards moisture. • Co(II)-doped MOF-5 can act as new sensing material for sensing small molecules.« less

  17. Overcrowding in emergency departments: A review of strategies to decrease future challenges.

    PubMed

    Yarmohammadian, Mohammad H; Rezaei, Fatemeh; Haghshenas, Abbas; Tavakoli, Nahid

    2017-01-01

    Emergency departments (EDs) are the most challenging ward with respect to patient delay. The goal of this study is to present strategies that have proven to reduce delay and overcrowding in EDs. In this review article, initial electronic database search resulted in a total of 1006 articles. Thirty articles were included after reviewing full texts. Inclusion criteria were assessments of real patient flows and implementing strategies inside the hospitals. In this study, we discussed strategies of team triage, point-of-care testing, ideal ED patient journey models, streaming, and fast track. Patients might be directed to different streaming channels depending on clinical status and required practitioners. The most comprehensive strategy is ideal ED patient journey models, in which ten interrelated substrategies are provided. ED leaders should apply strategies that provide a continuous care process without deeply depending on external services.

  18. A proposed simulation optimization model framework for emergency department problems in public hospital

    NASA Astrophysics Data System (ADS)

    Ibrahim, Ireen Munira; Liong, Choong-Yeun; Bakar, Sakhinah Abu; Ahmad, Norazura; Najmuddin, Ahmad Farid

    2015-12-01

    The Emergency Department (ED) is a very complex system with limited resources to support increase in demand. ED services are considered as good quality if they can meet the patient's expectation. Long waiting times and length of stay is always the main problem faced by the management. The management of ED should give greater emphasis on their capacity of resources in order to increase the quality of services, which conforms to patient satisfaction. This paper is a review of work in progress of a study being conducted in a government hospital in Selangor, Malaysia. This paper proposed a simulation optimization model framework which is used to study ED operations and problems as well as to find an optimal solution to the problems. The integration of simulation and optimization is hoped can assist management in decision making process regarding their resource capacity planning in order to improve current and future ED operations.

  19. Production of Monosugars from Lignocellulosic Biomass in Molten Salt Hydrates: Process Design and Techno-Economic Analysis

    PubMed Central

    2017-01-01

    ZnCl2 hydrate, the main molten salt used in biomass conversion, combined with low concentration HCl is an excellent solvent for the dissolution and hydrolysis of the carbohydrates present in lignocellulosic biomass. The most recalcitrant carbohydrate, cellulose, is dissolved in a residence time less than 1 h under mild conditions without significant degradation. This technology is referred to as BIOeCON-solvent technology. Separation of the sugars from the solution is the main challenge. The earlier conclusion regarding the potential of zeolite beta for selective adsorption has been used as the basis of a scale-up study. The technology of choice is continuous chromatographic separation (e.g., simulated moving bed, SMB). The sugar monomers are separated from the sugar oligomers, allowing the production of monosugars at high yield, using water as an eluent. Results of a pilot plant study are presented showing a stable operation at high selectivity. Several process designs are discussed, and the techno-economic performance of the BIOeCON-solvent technology is demonstrated by comparison with the state-of-the-art technology of NREL (National Renewable Energy Laboratory), which is based on enzymatic conversion of cellulose. It is concluded that the BIOeCON-solvent technology is technically and economically viable and is competitive to the NREL process. Because the BIOeCON-solvent process is in an early stage of development and far from fully optimized, it has the potential to outperform the existing processes. PMID:29170600

  20. Production of Monosugars from Lignocellulosic Biomass in Molten Salt Hydrates: Process Design and Techno-Economic Analysis.

    PubMed

    van den Bergh, Johan; Babich, Igor V; O'Connor, Paul; Moulijn, Jacob A

    2017-11-15

    ZnCl 2 hydrate, the main molten salt used in biomass conversion, combined with low concentration HCl is an excellent solvent for the dissolution and hydrolysis of the carbohydrates present in lignocellulosic biomass. The most recalcitrant carbohydrate, cellulose, is dissolved in a residence time less than 1 h under mild conditions without significant degradation. This technology is referred to as BIOeCON-solvent technology. Separation of the sugars from the solution is the main challenge. The earlier conclusion regarding the potential of zeolite beta for selective adsorption has been used as the basis of a scale-up study. The technology of choice is continuous chromatographic separation (e.g., simulated moving bed, SMB). The sugar monomers are separated from the sugar oligomers, allowing the production of monosugars at high yield, using water as an eluent. Results of a pilot plant study are presented showing a stable operation at high selectivity. Several process designs are discussed, and the techno-economic performance of the BIOeCON-solvent technology is demonstrated by comparison with the state-of-the-art technology of NREL (National Renewable Energy Laboratory), which is based on enzymatic conversion of cellulose. It is concluded that the BIOeCON-solvent technology is technically and economically viable and is competitive to the NREL process. Because the BIOeCON-solvent process is in an early stage of development and far from fully optimized, it has the potential to outperform the existing processes.

  1. Main chemical species and molecular structure of deep eutectic solvent studied by experiments with DFT calculation: a case of choline chloride and magnesium chloride hexahydrate.

    PubMed

    Zhang, Chao; Jia, Yongzhong; Jing, Yan; Wang, Huaiyou; Hong, Kai

    2014-08-01

    The infrared spectrum of deep eutectic solvent of choline chloride and magnesium chloride hexahydrate was measured by the FTIR spectroscopy and analyzed with the aid of DFT calculations. The main chemical species and molecular structure in deep eutectic solvent of [MgClm(H2O)6-m]2-m and [ChxCly]x+y complexes were mainly identified and the active ion of magnesium complex during the electrochemical process was obtained. The mechanism of the electrochemical process of deep eutectic solvent of choline chloride and magnesium chloride hexahydrate was well explained by combination theoretical calculations and experimental. Besides, based on our results we proposed a new system for the dehydration study of magnesium chloride hexahydrate.

  2. N,N'-DICYCLOHEXYL-N"-ISOTRIDECYLGUANIDINE AS SUPPRESSOR FOR THE NEXT GENERATION CAUSTIC SIDE SOLVENT EXTRACTION (NG-CSSX) PROCESS

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Duncan, Nathan C; Roach, Benjamin D; Williams, Neil J

    2012-01-01

    ABSTRACT The purity, concentration, and source of the N,N'-dicyclohexyl-N"-isotridecylguanidine (DCiTG) suppressor (guanidine) used in the NG-CSSX process were found to influence solvent performance. As the starting isotridecanol used in the preparation of DCiTG is comprised of a mixture of branched-chain aliphatic alcohols, varying in composition with manufacturer, the resulting DCiTG itself is a mixture. Thus, it is necessary to address how the solvent performance will be affected by the different preparations of the DCiTG solvent component. In this study, four preparations of DCiTG from three sources were analyzed and evaluated for purity and performance, both in the absence and presencemore » of an anionic surfactant impurity.« less

  3. Disentangled solid state and metastable polymer melt; a solvent free route to high-modulus high-strength tapes and films of UHMWPE

    NASA Astrophysics Data System (ADS)

    Rastogi, Sanjay

    2013-03-01

    Ultra High Molecular Weight Polyethylene (UHMWPE) having average molar mass greater than a million g/mol is an engineering polymer. Due to its light-weight, high abrasion resistance and biocompatibility it is used for demanding applications such as body armour, prostheses etc. At present, because of its high melt viscosity to achieve the uniaxial/biaxial properties in the form of fibers/films the polymer is processed via solution route where nearly 95wt% of the solvent is used to process 5wt% of the polymer. In past several attempts have been made to process the polymer without using any solvent. However, compared to the solvent processing route the achieved mechanical properties were rather poor. Here we show that by controlled synthesis it is feasible to obtain UHMWPE that could be processed free of solvent to make uniaxial tapes and biaxial films, having unprecedented mechanical properties, exceeding that of the solution spun fibers. We address some of the fundamental aspects of chemistry, physics, rheology and processing for the development of desired morphological features to achieve the ultimate mechanical properties in tapes and films. The paper will also address the metastable melt state obtained on melting of the disentangled crystals and its implication on rheology in linear and nonlinear viscoelastic region. Solid state NMR studies will be applied to establish disentangled state in solid state to the polymerisation conditions. References: Macromolecules 2011, 44(14), 5558-5568; Nature Materials 2005, 4, 635-641; Phys Rev Lett 2006, 96(21), 218303-218205. The authors acknowledge financial support by the Dutch Polymer Institute.

  4. Exploratory Development on a New Process to Produce Improved RDX crystals: Supercritical Fluid Anti-Solvent Recrystallization

    DTIC Science & Technology

    1988-05-02

    G. and J. Chiovini. Decaffeination Process . U.S. Patent 4,251.559; 17 February 1981. 43. Friedrich, J.P.. G.R. List, and A.J. Leakin. Petroleum...0 CONTRACT REPORT BRL-CR-606 EXPLORATORY DEVELOPMENT ON A NEW PROCESS TO PRODUCE IMPROVED RDX CRYSTALS: SUPERCRITICAL FLUID ANTI-SOLVENT...CCESSION NO. 11. TITLE (icnude Sun• y Uasuihcanon) I . • EXPLORATORY DEVELOPMENT ON A NEW PROCESS TO PRODUCE IMPROVED RDX CRYSTALS: SUPERCRITICAL

  5. Crystal morphology optimization of thiamine hydrochloride in solvent system: Experimental and molecular dynamics simulation studies

    NASA Astrophysics Data System (ADS)

    Yang, Yang; Han, Dandan; Du, Shichao; Wu, Songgu; Gong, Junbo

    2018-01-01

    Thiamine hydrochloride (THCL) was produced in methanol accompanied with agglomeration in industry, the plate like morphology of THCL in methanol was not deserve to have a good quality. Selecting a suitable solvent should be considered because solvent could be one of the essential factors to impact morphology. Methanol and methanol/ethyl acetate solvent (0.2 vol fraction of methanol) was selected as the solvent system in reactive crystallization of THCL. The experiment results show the THCL crystal morphology in methanol/ethyl acetate solvent system was granular and more regular than that in methanol. In order to explicate the different crystal morphology in different solvents, molecular dynamics (MD) simulation was introduced to simulate crystal morphology in different solvents. The attachment energy (AE) model was employed to investigate the morphology of THCL under vacuum conditions, methanol and methanol/ethyl acetate solvent conditions, respectively. The simulation crystal morphology was in a good agreement with that of experimented. The particle of THCL in methanol/ethyl acetate solvent has less tendency to agglomeration, and then it is favorable to the downstream process, such as filtration, storage and transportation.

  6. Issues Related to Cleaning Complex Geometry Surfaces with ODC-Free Solvents

    NASA Technical Reports Server (NTRS)

    Bradford, Blake F.; Wurth, Laura A.; Nayate, Pramod D.; McCool, Alex (Technical Monitor)

    2001-01-01

    Implementing ozone depleting chemicals (ODC)-free solvents into full-scale reusable solid rocket motor cleaning operations has presented problems due to the low vapor pressures of the solvents. Because of slow evaporation, solvent retention is a problem on porous substrates or on surfaces with irregular geometry, such as threaded boltholes, leak check ports, and nozzle backfill joints. The new solvents are being evaluated to replace 1,1,1-trichloroethane, which readily evaporates from these surfaces. Selection of the solvents to be evaluated on full-scale hardware was made based on results of subscale tests performed with flat surface coupons, which did not manifest the problem. Test efforts have been undertaken to address concerns with the slow-evaporating solvents. These concerns include effects on materials due to long-term exposure to solvent, potential migration from bolthole threads to seal surfaces, and effects on bolt loading due to solvent retention in threads. Tests performed to date have verified that retained solvent does not affect materials or hardware performance. Process modifications have also been developed to assist drying, and these can be implemented if additional drying becomes necessary.

  7. Insight into effects of electro-dewatering pretreatment on nitrous oxide emission involved in related functional genes in sewage sludge composting.

    PubMed

    Wang, Ke; Wu, Yiqi; Wang, Zhe; Wang, Wei; Ren, Nanqi

    2018-05-26

    Electro-dewatering (ED) pretreatment could improve sludge dewatering performance and remove heavy metal, but the effect of ED pretreatment on nitrous oxide (N 2 O) emission and related functional genes in sludge composting process is still unknown, which was firstly investigated in this study. The results revealed that ED pretreatment changed the physicochemical characteristics of sludge and impacted N 2 O related functional genes, resulting in the reduction of cumulative N 2 O emission by 77.04% during 60 days composting. The higher pH and NH 4 + -N, but lower moisture, ORP and NO 2 - -N emerged in the composting of ED sludge compared to mechanical dewatering (MD) sludge. Furthermore, ED pretreatment reduced amoA, hao, narG, nirK and nosZ in ED sludge on Day-10 and Day-60 of composting. It was found that nirK reduction was the major factor impacting N 2 O generation in the initial composting of ED sludge, and the decline of amoA restricted N 2 O production in the curing period. Copyright © 2018 Elsevier Ltd. All rights reserved.

  8. The past, present, and future of urgent matters: lessons learned from a decade of emergency department flow improvement.

    PubMed

    McClelland, Mark Stephen; Lazar, Danielle; Sears, Vickie; Wilson, Marcia; Siegel, Bruce; Pines, Jesse M

    2011-12-01

    Over the past decade, emergency departments (ED) have encountered major challenges due to increased crowding and a greater public focus on quality measurement and quality improvement. Responding to these challenges, many EDs have worked to improve their processes and develop new and innovative models of care delivery. Urgent Matters has contributed to ED quality and patient flow improvement by working with hospitals throughout the United States. Recognizing that EDs across the country are struggling with many of the same issues, Urgent Matters-a program funded by the Robert Wood Johnson Foundation (RWJF)-has sought to identify, develop, and disseminate innovative approaches, interventions, and models to improve ED flow and quality. Using a variety of techniques, such as learning networks (collaboratives), national conferences, e-newsletters, webinars, best practices toolkits, and social media, Urgent Matters has served as a thought leader and innovator in ED quality improvement initiatives. The Urgent Matters Seven Success Factors were drawn from the early work done by program participants and propose practical guidelines for implementing and sustaining ED improvement activities. This article chronicles the history, activities, lessons learned, and future of the Urgent Matters program. © 2011 by the Society for Academic Emergency Medicine.

  9. Throughput increase by adjustment of the BARC drying time with coat track process

    NASA Astrophysics Data System (ADS)

    Brakensiek, Nickolas L.; Long, Ryan

    2005-05-01

    Throughput of a coater module within the coater track is related to the solvent evaporation rate from the material that is being coated. Evaporation rate is controlled by the spin dynamics of the wafer and airflow dynamics over the wafer. Balancing these effects is the key to achieving very uniform coatings across a flat unpatterned wafer. As today"s coat tracks are being pushed to higher throughputs to match the scanner, the coat module throughput must be increased as well. For chemical manufacturers the evaporation rate of the material depends on the solvent used. One measure of relative evaporation rates is to compare flash points of a solvent. The lower the flash point, the quicker the solvent will evaporate. It is possible to formulate products with these volatile solvents although at a price. Shipping and manufacturing a more flammable product increase chances of fire, thereby increasing insurance premiums. Also, the end user of these chemicals will have to take extra precautions in the fab and in storage of these more flammable chemicals. An alternative coat process is possible which would allow higher throughput in a distinct coat module without sacrificing safety. A tradeoff is required for this process, that being a more complicated coat process and a higher viscosity chemical. The coat process uses the fact that evaporation rate depends on the spin dynamics of the wafer by utilizing a series of spin speeds that first would set the thickness of the material followed by a high spin speed to remove the residual solvent. This new process can yield a throughput of over 150 wafers per hour (wph) given two coat modules. The thickness uniformity of less than 2 nm (3 sigma) is still excellent, while drying times are shorter than 10 seconds to achieve the 150 wph throughput targets.

  10. Genital image, sexual anxiety, and erectile dysfunction among young male military personnel.

    PubMed

    Wilcox, Sherrie L; Redmond, Sarah; Davis, Teaniese L

    2015-06-01

    More than a third of young military personnel report experiencing some level of erectile dysfunction (ED). Preoccupation with body image, particularly genitals, is a distraction that can influence sexual anxiety (SA) and sexual functioning problems (SFPs), particularly ED. This study assessed the relationships between male genital self-image (MGSI), SA, and ED in a sample of male military personnel age 40 or younger. Data were from a larger study on SFPs in military populations. This sample consisted of 367 male military personnel age 40 or younger. Hierarchical regression analyses and process modeling using mediation analysis were performed to examine the effects of MGSI on ED with SA as an intermediate variable. We predicted that SA would mediate the relationship between MGSI and ED. ED severity was assessed with the International Index of Erectile Function. MGSI was assessed using the MGSI Scale. SA was assessed with the SA subscale of the Sexual Needs Scale. As hypothesized, greater satisfaction with MGSI was predictive of significantly lower SA (F[8, 352] = 4.07, P = 0.001) and lower ED (F[8, 352] = 13.20, P = 0.001). Lower levels of SA were predictive of lower levels of ED (F[8, 354] = 21.35, P < 0.001). Additionally, results also revealed a significant indirect effect of MGSI on ED through SA (b = -0.07, standard error = 0.03, confidence interval = [-0.14,-0.02], P < 0.05), indicating mediation of MGSI on ED via SA. This study underscores the complex etiologic basis of SFPs, particularly ED, and highlights the importance of considering psychologic contributors to ED, such as SA and MGSI. Strategies aimed at reducing SA may be useful in improving ED in young military populations and are worth considering as complements to strategies that improve SFPs. © 2015 International Society for Sexual Medicine.

  11. Meeting the Next Generation Science Standards Through "Rediscovered" Climate Model Experiments

    NASA Astrophysics Data System (ADS)

    Sohl, L. E.; Chandler, M. A.; Zhou, J.

    2013-12-01

    Since the Educational Global Climate Model (EdGCM) Project made its debut in January 2005, over 150 institutions have employed EdGCM software for a variety of uses ranging from short lab exercises to semester-long and year-long thesis projects. The vast majority of these EdGCM adoptees have been at the undergraduate and graduate levels, with few users at the K-12 level. The K-12 instructors who have worked with EdGCM in professional development settings have commented that, although EdGCM can be used to illustrate a number of the Disciplinary Core Ideas and connects to many of the Common Core State Standards across subjects and grade levels, significant hurdles preclude easy integration of EdGCM into their curricula. Time constraints, a scarcity of curriculum materials, and classroom technology are often mentioned as obstacles in providing experiences to younger grade levels in realistic climate modeling research. Given that the NGSS incorporates student performance expectations relating to Earth System Science, and to climate science and the human dimension in particular, we feel that a streamlined version of EdGCM -- one that eliminates the need to run the climate model on limited computing resources, and provides a more guided climate modeling experience -- would be highly beneficial for the K-12 community. This new tool currently under development, called EzGCM, functions through a browser interface, and presents "rediscovery experiments" that allow students to do their own exploration of model output from published climate experiments, or from sensitivity experiments designed to illustrate how climate models as well as the climate system work. The experiments include background information and sample questions, with more extensive notes for instructors so that the instructors can design their own reflection questions or follow-on activities relating to physical or human impacts, as they choose. An added benefit of the EzGCM tool is that, like EdGCM, it helps illustrate the process of doing research on a complex topic, in a way that builds upon earlier experiences in inquiry-based learning. By having students work through a multi-stage process that requires them to plan several steps ahead, through data processing, analysis and interpretation, they learn how to do research in addition to improving their understanding of climate change.

  12. Effects of alcohol solvents on anatase TiO2 nanocrystals prepared by microwave-assisted solvothermal method

    NASA Astrophysics Data System (ADS)

    Wu, Yu-Chun; Tai, Yu-Chuen

    2013-06-01

    The effects of solvents on the anatase crystallite size prepared by sol-gel microwave-assisted solvothermal method were investigated in this study. Eight different alcohol solvents classified into two groups, i.e. primary and secondary/ternary alcohols, were used as reaction media and the effects of solvent properties, such as dielectric constant, boiling point, and internal pressure during the solvothermal process, on the crystallite size and shape were analyzed. According to the experimental results, selecting the solvent type allowed not only the alteration of the crystallite size but also the crystallite shape without the need of any additives. The boiling point of solvent was determined as the major factor influencing the crystallite size. Among the solvents with similar boiling points, the solvent with a higher carbon number produced the smaller crystallite size because of steric hindrance effect. In addition, the carboxyl groups dissociated from the alcohol solvent can play a role as a structural capping agent to retard the anatase crystal growth along the [001] direction and led to a rectangular crystallite shape with preferred development in {001} facets. On the other hand, the alcoholysis reaction was found easily occurred between the primary alcohol and isopropoxide that effectively limited the hydrolysis and condensation processes but also suppressed the structural capping effect. Therefore, the anatase crystals prepared in the primary alcohols became exceptionally small and showed spherical shape. Finally, the anatase crystals prepared using isopropanol demonstrated the highest photocatalytic activity due to its evident preferred crystallization in the {001} facets.

  13. Food portion size and energy density evoke different patterns of brain activation in children12

    PubMed Central

    Fearnbach, S Nicole; Wilson, Stephen J; Fisher, Jennifer O; Savage, Jennifer S; Rolls, Barbara J; Keller, Kathleen L

    2017-01-01

    Background: Large portions of food promote intake, but the mechanisms that drive this effect are unclear. Previous neuroimaging studies have identified the brain-reward and decision-making systems that are involved in the response to the energy density (ED) (kilocalories per gram) of foods, but few studies have examined the brain response to the food portion size (PS). Objective: We used functional MRI (fMRI) to determine the brain response to food images that differed in PSs (large and small) and ED (high and low). Design: Block-design fMRI was used to assess the blood oxygen level–dependent (BOLD) response to images in 36 children (7–10 y old; girls: 50%), which was tested after a 2-h fast. Pre-fMRI fullness and liking were rated on visual analog scales. A whole-brain cluster-corrected analysis was used to compare BOLD activation for main effects of the PS, ED, and their interaction. Secondary analyses were used to associate BOLD contrast values with appetitive traits and laboratory intake from meals for which the portions of all foods were increased. Results: Compared with small-PS cues, large-PS cues were associated with decreased activation in the inferior frontal gyrus (P < 0.01). Compared with low-ED cues, high-ED cues were associated with increased activation in multiple regions (e.g., in the caudate, cingulate, and precentral gyrus) and decreased activation in the insula and superior temporal gyrus (P < 0.01 for all). A PS × ED interaction was shown in the superior temporal gyrus (P < 0.01). BOLD contrast values for high-ED cues compared with low-ED cues in the insula, declive, and precentral gyrus were negatively related to appetitive traits (P < 0.05). There were no associations between the brain response to the PS and either appetitive traits or intake. Conclusions: Cues regarding food PS may be processed in the lateral prefrontal cortex, which is a region that is implicated in cognitive control, whereas ED activates multiple areas involved in sensory and reward processing. Possible implications include the development of interventions that target decision-making and reward systems differently to moderate overeating. PMID:27881393

  14. Emergency medicine in the Veterans Health Administration-results from a nationwide survey.

    PubMed

    Ward, Michael J; Collins, Sean P; Pines, Jesse M; Dill, Curt; Tyndall, Gary; Kessler, Chad S

    2015-07-01

    We describe emergency physician staffing, capabilities, and academic practices in US Veterans Health Administration (VHA) emergency departments (EDs). As part of an ongoing process improvement effort for the VHA emergency care system, VHA-wide surveys are conducted among ED medical directors every 3 years. Web-based surveys of VHA ED directors were conducted in 2013 on clinical operations and academic program development. We describe the results from the 2013 survey. When available, we compare responses with the previously administered survey from 2010. A total of 118 of 118 ED directors filled out the survey in 2013 (100% response rate). Respondents reported that 45.5% of VHA emergency physicians are board certified in emergency medicine, and 95% spend most their time in direct patient care. Clinical care is also provided by part-time (<0.5 full-time employee equivalent) emergency physicians in 59.3% of EDs. More than half of EDs (57%) provide on-site tissue plasminogen activator for acute ischemic stroke patients, and only 39% can administer tissue plasminogen activator 24 hours per day, 7 days per week. Less than half (48.3%) of EDs have emergency Obstetrics and Gynecology consultation availability. Most VHA EDs (78.8%) have a university affiliation, but only 21.5% participated in the respective academic emergency medicine program. Veterans Health Administration emergency physicians have primarily clinical responsibilities, and less than half have formal emergency medicine board certification. Despite most VHA EDs having university affiliations, traditional academic activities (eg, teaching and research) are performed in only 1 in 3 VHA EDs. Less than half of VHA EDs have availability of consulting services, including advanced stroke care and women's health. Published by Elsevier Inc.

  15. Lipase mediated synthesis of rutin fatty ester: Study of its process parameters and solvent polarity.

    PubMed

    Vaisali, C; Belur, Prasanna D; Regupathi, Iyyaswami

    2017-10-01

    Lipophilization of antioxidants is recognized as an effective strategy to enhance solubility and thus effectiveness in lipid based food. In this study, an effort was made to optimize rutin fatty ester synthesis in two different solvent systems to understand the influence of reaction system hydrophobicity on the optimum conditions using immobilised Candida antartica lipase. Under unoptimized conditions, 52.14% and 13.02% conversion was achieved in acetone and tert-butanol solvent systems, respectively. Among all the process parameters, water activity of the system was found to show highest influence on the conversion in each reaction system. In the presence of molecular sieves, the ester production increased to 62.9% in tert-butanol system, unlike acetone system. Under optimal conditions, conversion increased to 60.74% and 65.73% in acetone and tert-butanol system, respectively. This study shows, maintaining optimal water activity is crucial in reaction systems having polar solvents compared to more non-polar solvents. Copyright © 2017 Elsevier Ltd. All rights reserved.

  16. SOLVENT EXTRACTION PROCESS FOR THE SEPARATION OF URANIUM AND THORIUM FROM PROTACTINIUM AND FISSION PRODUCTS

    DOEpatents

    Rainey, R.H.; Moore, J.G.

    1962-08-14

    A liquid-liquid extraction process was developed for recovering thorium and uranium values from a neutron irradiated thorium composition. They are separated from a solvent extraction system comprising a first end extraction stage for introducing an aqueous feed containing thorium and uranium into the system consisting of a plurality of intermediate extractiorr stages and a second end extractron stage for introducing an aqueous immiscible selective organic solvent for thorium and uranium in countercurrent contact therein with the aqueous feed. A nitrate iondeficient aqueous feed solution containing thorium and uranium was introduced into the first end extraction stage in countercurrent contact with the organic solvent entering the system from the second end extraction stage while intro ducing an aqueous solution of salting nitric acid into any one of the intermediate extraction stages of the system. The resultant thorium and uranium-laden organic solvent was removed at a point preceding the first end extraction stage of the system. (AEC)

  17. Separation properties of aluminium-plastic laminates in post-consumer Tetra Pak with mixed organic solvent.

    PubMed

    Zhang, S F; Zhang, L L; Luo, K; Sun, Z X; Mei, X X

    2014-04-01

    The separation properties of the aluminium-plastic laminates in postconsumer Tetra Pak structure were studied in this present work. The organic solvent blend of benzene-ethyl alcohol-water was used as the separation reagent. Then triangle coordinate figure analysis was taken to optimize the volume proportion of various components in the separating agent and separation process. And the separation temperature of aluminium-plastic laminates was determined by the separation time, efficiency, and total mass loss of products. The results show that cost-efficient separations perform best with low usage of solvents at certain temperatures, for certain times, and within a certain range of volume proportions of the three components in the solvent agent. It is also found that similar solubility parameters of solvents and polyethylene adhesives (range 26.06-34.85) are a key factor for the separation of the aluminium-plastic laminates. Such multisolvent processes based on the combined-system concept will be vital to applications in the recycling industry.

  18. Effect of solvents on the bulk growth of 4-aminobenzophenone single crystals: A potential material for blue and green lasers

    NASA Astrophysics Data System (ADS)

    Natarajan, V.; Usharani, S.; Arivanandhan, M.; Anandan, P.; Hayakawa, Y.

    2015-06-01

    Although 4-aminobenzophenone (4-ABP) is the best derivative of benzophenone with 260 times higher second harmonic generation (SHG) efficiency than potassium dihydrogen phosphate (KDP), growth of high quality bulk crystal still remains a difficult task. In the present work, the effect of solvents on solubility and growth aspects of 4-ABP was investigated to grow inclusion free 4-ABP crystals. The growth processes were discussed based on solute-solvent interaction in two different growth media of ethyl acetate and ethanol. The growth rate and thereby solvent inclusions are relatively higher in ethyl acetate grown crystal than the crystal grown from ethanol. The structural, thermal and optical properties of 4-ABP crystals were studied. The enthalpy of 4-ABP melting process was estimated from differential thermal analysis. The optical transmission study shows that 4-ABP crystals grown from ethanol has high transparency compared to ethyl acetate grown sample due to solvent inclusion in the later crystal.

  19. Formation of indomethacin-saccharin cocrystals using supercritical fluid technology.

    PubMed

    Padrela, Luis; Rodrigues, Miguel A; Velaga, Sitaram P; Matos, Henrique A; de Azevedo, Edmundo Gomes

    2009-08-12

    The main objective of the present work is to check the feasibility of supercritical fluid (SCF) technologies in the screening and design of cocrystals (novel crystalline solids). The cocrystal formation tendencies in three different SCF techniques, focusing on distinct supercritical fluid properties - solvent, anti-solvent and atomization enhancer - were investigated. The effect of processing parameters on the cocrystal formation behaviour and particle properties in these techniques was also studied. A recently reported indomethacin-saccharin (IND-SAC) cocrystalline system was our model system. A 1:1 molar ratio of indomethacin (gamma-form) and saccharin was used as a starting material. The SCF techniques employed in the study include the CSS technique (cocrystallization with supercritical solvent), the SAS technique (supercritical anti-solvent), and the AAS technique (atomization and anti-solvent). The resulting cocrystalline phase was identified using differential scanning calorimetry (DSC), powder X-ray diffraction (PXRD), and Fourier transform-Raman (FT-Raman). The particle morphologies and size distributions were determined using scanning electron microscopy (SEM) and aerosizer, respectively. The pure IND-SAC cocrystals were obtained from SAS and AAS processes, whilst partial to no cocrystal formation occurred in the CSS process. However, no remarkable differences were observed in terms of cocrystal formation at different processing conditions in SAS and AAS processes. Particles from CSS processes were agglomerated and large, whilst needle-to-block-shaped and spherical particles were obtained from SAS and AAS processes, respectively. The particle size distribution of these particles was 0.2-5microm. Particulate IND-SAC cocrystals with different morphologies and sizes (nano-to-micron) were produced using supercritical fluid techniques. This work demonstrates the potential of SCF technologies as screening methods for cocrystals with possibilities for particle engineering.

  20. Solvent-assisted lipid bilayer formation on silicon dioxide and gold.

    PubMed

    Tabaei, Seyed R; Choi, Jae-Hyeok; Haw Zan, Goh; Zhdanov, Vladimir P; Cho, Nam-Joon

    2014-09-02

    Planar lipid bilayers on solid supports mimic the fundamental structure of biological membranes and can be investigated using a wide range of surface-sensitive techniques. Despite these advantages, planar bilayer fabrication is challenging, and there are no simple universal methods to form such bilayers on diverse material substrates. One of the novel methods recently proposed and proven to form a planar bilayer on silicon dioxide involves lipid deposition in organic solvent and solvent exchange to influence the phase of adsorbed lipids. To scrutinize the specifics of this solvent-assisted lipid bilayer (SALB) formation method and clarify the limits of its applicability, we have developed a simplified, continuous solvent-exchange version to form planar bilayers on silicon dioxide, gold, and alkanethiol-coated gold (in the latter case, a lipid monolayer is formed to yield a hybrid bilayer) and varied the type of organic solvent and rate of solvent exchange. By tracking the SALB formation process with simultaneous quartz crystal microbalance-dissipation (QCM-D) and ellipsometry, it was determined that the acoustic, optical, and hydration masses along with the acoustic and optical thicknesses, measured at the end of the process, are comparable to those observed by employing conventional fabrication methods (e.g., vesicle fusion). As shown by QCM-D measurements, the obtained planar bilayers are highly resistant to protein adsorption, and several, but not all, water-miscible organic solvents could be successfully used in the SALB procedure, with isopropanol yielding particularly high-quality bilayers. In addition, fluorescence recovery after photobleaching (FRAP) measurements demonstrated that the coefficient of lateral lipid diffusion in the fabricated bilayers corresponds to that measured earlier in the planar bilayers formed by vesicle fusion. With increasing rate of solvent exchange, it was also observed that the bilayer became incomplete and a phenomenological model was developed in order to explain this feature. The results obtained allowed us to clarify and discriminate likely steps of the SALB formation process as well as determine the corresponding influence of organic solvent type and flow conditions on these steps. Taken together, the findings demonstrate that the SALB formation method can be adapted to a continuous solvent-exchange procedure that is technically minimal, quick, and efficient to form planar bilayers on solid supports.

  1. ED pharmacist monitoring of provider antibiotic selection aids appropriate treatment for outpatient UTI.

    PubMed

    Lingenfelter, Erin; Drapkin, Zachary; Fritz, Kelly; Youngquist, Scott; Madsen, Troy; Fix, Megan

    2016-08-01

    We sought to determine whether an emergency department (ED) pharmacist could aid in the monitoring and correction of inappropriate empiric antibiotic selection for urinary tract infections in an outpatient ED population. Urine cultures with greater than 100 000 CFU/mL bacteria from the University of Utah Emergency Department over 1 year (October 2011-Sept 2012) were identified using our electronic medical record system. Per ED protocol, an ED pharmacist reviews all cultures and performs a chart review of patient symptoms, diagnosis, and discharge antibiotics to determine whether the treatment was appropriate. A retrospective review of this process was performed to identify how often inappropriate treatment was recognized and intervened on by an ED pharmacist. Of the 180 cultures included, a total of 42 (23%) of empiric discharge treatments were considered inappropriate and required intervention. In 35 (83%) of 42 patients, the ED pharmacist was able to contact the patient and make appropriate changes; the remaining 7 patients were unable to be contacted, and no change could be made in their treatment. A chart review of all urine cultures with greater than 100 000 CFU/mL performed by an ED pharmacist helped identify inappropriate treatment in 23% of patients discharged to home with the diagnosis of urinary tract infection. Of these patients who had received inappropriate treatment, an ED pharmacist was able to intervene in 83% of cases. These data highlight the role of ED pharmacists in improving patient care after discharge. Copyright © 2016 Elsevier Inc. All rights reserved.

  2. Safety and efficiency of emergency department interrogation of cardiac devices

    PubMed Central

    Neuenschwander, James F.; Peacock, W. Frank; Migeed, Madgy; Hunter, Sara A.; Daughtery, John C.; McCleese, Ian C.; Hiestand, Brian C.

    2016-01-01

    Objective Patients with implanted cardiac devices may wait extended periods for interrogation in emergency departments (EDs). Our purpose was to determine if device interrogation could be done safely and faster by ED staff. Methods Prospective randomized, standard therapy controlled, trial of ED staff device interrogation vs. standard process (SP), with 30-day follow-up. Eligibility criteria: ED presentation with a self-report of a potential device related complaint, with signed informed consent. SP interrogation was by company representative or hospital employee. Results Of 60 patients, 42 (70%) were male, all were white, with a median (interquartile range) age of 71 (64 to 82) years. No patient was lost to follow up. Of all patients, 32 (53%) were enrolled during business hours. The overall median (interquartile range) ED vs. SP time to interrogation was 98.5 (40 to 260) vs. 166.5 (64 to 412) minutes (P=0.013). While ED and SP interrogation times were similar during business hours, 102 (59 to 138) vs. 105 (64 to 172) minutes (P=0.62), ED interrogation times were shorter vs. SP during non-business hours; 97 (60 to 126) vs. 225 (144 to 412) minutes, P=0.002, respectively. There was no difference in ED length of stay between the ED and SP interrogation, 249 (153 to 390) vs. 246 (143 to 333) minutes (P=0.71), regardless of time of presentation. No patient in any cohort suffered an unplanned medical contact or post-discharge adverse device related event. Conclusion ED staff cardiac device interrogations are faster, and with similar 30-day outcomes, as compared to SP. PMID:28168230

  3. Safety and efficiency of emergency department interrogation of cardiac devices.

    PubMed

    Neuenschwander, James F; Peacock, W Frank; Migeed, Madgy; Hunter, Sara A; Daughtery, John C; McCleese, Ian C; Hiestand, Brian C

    2016-12-01

    Patients with implanted cardiac devices may wait extended periods for interrogation in emergency departments (EDs). Our purpose was to determine if device interrogation could be done safely and faster by ED staff. Prospective randomized, standard therapy controlled, trial of ED staff device interrogation vs. standard process (SP), with 30-day follow-up. Eligibility criteria: ED presentation with a self-report of a potential device related complaint, with signed informed consent. SP interrogation was by company representative or hospital employee. Of 60 patients, 42 (70%) were male, all were white, with a median (interquartile range) age of 71 (64 to 82) years. No patient was lost to follow up. Of all patients, 32 (53%) were enrolled during business hours. The overall median (interquartile range) ED vs. SP time to interrogation was 98.5 (40 to 260) vs. 166.5 (64 to 412) minutes (P=0.013). While ED and SP interrogation times were similar during business hours, 102 (59 to 138) vs. 105 (64 to 172) minutes (P=0.62), ED interrogation times were shorter vs. SP during non-business hours; 97 (60 to 126) vs. 225 (144 to 412) minutes, P=0.002, respectively. There was no difference in ED length of stay between the ED and SP interrogation, 249 (153 to 390) vs. 246 (143 to 333) minutes (P=0.71), regardless of time of presentation. No patient in any cohort suffered an unplanned medical contact or post-discharge adverse device related event. ED staff cardiac device interrogations are faster, and with similar 30-day outcomes, as compared to SP.

  4. Development of emergency department load relief area--gauging benefits in empirical terms.

    PubMed

    Rasheed, Farrukh; Lee, Young Hoon; Kim, Seung Ho; Park, In Cheol

    2012-12-01

    The primary goal of this investigation was to develop a simulation model to evaluate the various internal and external factors affecting patient flow and crowding in the emergency department (ED). In addition, a few recommendations are proposed to reconfigure the patient flow to improve ED capacity while maintaining service quality. In this research, we present a simulation study conducted in the ED at the "S Hospital" located in Seoul. Based on patient flow data and process analysis, a simulation model of patient throughput in the ED has been developed. We evaluated simulations of diverting the specific patient load in the light of our proposed recommendations to a separately managed area named as the ED load relief area (ED-LRA) and analyzing potential effects on overall length of stay (LOS) and waiting time (WT). What-if analyses have been proposed to identify key issues and investigate the improvements as per our proposed recommendations. The simulation results suggest that specific patient load diversion is needed to ensure desired outcomes. With the diversion of specific patient load to ED-LRA, there is a reduction of 40.60% in mean LOS and 42.5% in WT with improved resource utilization. As a result, opening of an ED-LRA is justified. Real-world systems are often too intricate for analytical models and often too expensive to trial with directly. Simulation models allow the modeling of this intricacy and enable experimentation to make inferences about how the actual system might perform. Our simulation study modeled that diverting the specific patient load to ED-LRA produced an improvement in overall ED's LOS and WT.

  5. Development of Acetic Acid Removal Technology for the UREX+Process

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Robert M. Counce; Jack S. Watson

    2009-06-30

    It is imperative that acetic acid is removed from a waste stream in the UREX+process so that nitric acid can be recycled and possible interference with downstreatm steps can be avoidec. Acetic acid arises from acetohydrozamic acid (AHA), and is used to suppress plutonium in the first step of the UREX+process. Later, it is hydrolyzed into hydroxyl amine nitrate and acetic acid. Many common separation technologies were examined, and solvent extraction was determined to be the best choice under process conditions. Solvents already used in the UREX+ process were then tested to determine if they would be sufficient for themore » removal of acetic acid. The tributyl phosphage (TBP)-dodecane diluent, used in both UREX and NPEX, was determined to be a solvent system that gave sufficient distribution coefficients for acetic acid in addition to a high separation factor from nitric acid.« less

  6. Supercritical antisolvent precipitation of nimesulide: preliminary experiments.

    PubMed

    Moneghini, M; Perissutti, B; Vecchione, F; Kikic, I; Alessi, P; Cortesi, A; Princivalle, F

    2007-07-01

    The purpose of this preliminary study was to investigate the physico-chemical properties of nimesulide precipitated by continuous supercritical antisolvent (SAS) from different organic solvents like acetone, chloroform and dichloromethane at 40 degrees C and 80, 85 and 88 bar, respectively. Scanning electron microscopy, differential scanning calorimetry, X-Ray diffractometry and in vitro dissolution tests were employed to study how the technological process and the solvent nature would affect the final product. SAS-processed nimesulide particles showed dramatic morphological change in crystalline structure if compared to native nimesulide, resulting in needle and thin rods shaped crystals. The solid state analysis showed that using chloroform or dichloromethane as a solvent the drug solid state remained substantially unchanged, whilst if using acetone the applied method caused a transition from the starting form I to the meta-stable form II. So as to identify which process was responsible for this result, nimesulide was further precipitated from the same solvent by conventional evaporation method (RV-sample). On the basis of this comparison, the solvent was found to be responsible for the re-organization into the different polymorphic form and the potential of the SAS process to produce micronic needle shaped particles, with an enhanced dissolution rate if compared to the to the pure drug, was ascertained. Finally, the stability of the nimesulide form II, checked by DSC analysis, was ruled on over a period of 15 months.

  7. Role of solvent in metal-on-metal surface diffusion: A case for rational solvent selection for materials synthesis

    NASA Astrophysics Data System (ADS)

    Imandi, Venkataramana; Jagannath, Mantha Sai Pavan; Chatterjee, Abhijit

    2018-09-01

    The effect of solvent on diffusion at metal surfaces is poorly understood despite its importance to morphological evolution during materials processing, corrosion and catalysis. In this article, we probe the metal-solvent interfacial structure, effective nature of interactions and dynamics when a solvent is in contact with a metal using a novel accelerated molecular dynamics simulation technique called temperature programmed molecular dynamics (TPMD). TPMD simulations reveal that surface diffusion of metal-on-metal can be made to vary over orders-of-magnitude by tuning the metal-solvent interaction. Ultimately, the solvent can have an indirect effect on diffusion. As the solvent tugs at the metal surface the separation between the adsorbed metal atom (adatom) and the surface layer can be modulated via metal-solvent interactions. The resulting adatom-surface separation can cause stronger/weaker binding of the adatom to the metal surface, which in turn results in the observed slower/enhanced diffusion in the presence of solvent. We believe this effect is ubiquitous in pure metal and metal alloys and in principle one could rationally select solvent to control the material structural evolution. Implications on materials synthesis are discussed in the context of formation of nanoporous materials.

  8. Process for extracting technetium from alkaline solutions

    DOEpatents

    Moyer, Bruce A.; Sachleben, Richard A.; Bonnesen, Peter V.

    1995-01-01

    A process for extracting technetium values from an aqueous alkaline solution containing at least one alkali metal hydroxide and at least one alkali metal nitrate, the at least one alkali metal nitrate having a concentration of from about 0.1 to 6 molar. The solution is contacted with a solvent consisting of a crown ether in a diluent for a period of time sufficient to selectively extract the technetium values from the aqueous alkaline solution. The solvent containing the technetium values is separated from the aqueous alkaline solution and the technetium values are stripped from the solvent.

  9. Disaggregation induced solvatochromic switch: A study of dansylated polyglycerol dendrons in binary solvent mixture

    NASA Astrophysics Data System (ADS)

    Subuddhi, Usharani; Vuram, Prasanna K.; Chadha, Anju; Mishra, Ashok K.

    2014-07-01

    A reversal in solvatochromic behaviour was observed in second and third generation glycerol based dansylated polyether dendrons in water on addition of a second solvent like methanol or acetonitrile. Below a certain percentage of the nonaqueous solvent there is a negative-solvatochromism observed and above that there is a switch to positive-solvatochromism. The negative-solvatochromism is attributed to the progressive disaggregation of the dendron aggregates by the nonaqueous solvent component. Once the disaggregation process is complete, positive-solvatochromism is exhibited by the dendron monomers. Higher the hydrophobicity of the dendron more is the amount of the second solvent required for disaggregation.

  10. Engaging stakeholders to design a comparative effectiveness trial in children with uncontrolled asthma

    PubMed Central

    Erwin, Kim; Martin, Molly A; Flippin, Tara; Norell, Sarah; Shadlyn, Ariana; Yang, Jie; Falco, Paula; Rivera, Jaime; Ignoffo, Stacy; Kumar, Rajesh; Margellos-Anast, Helen; McDermott, Michael; McMahon, Kate; Mosnaim, Giselle; Nyenhuis, Sharmilee M; Press, Valerie G; Ramsay, Jessica E; Soyemi, Kenneth; Thompson, Trevonne M; Krishnan, Jerry A

    2016-01-01

    Aim: To present the methods and outcomes of stakeholder engagement in the development of interventions for children presenting to the emergency department (ED) for uncontrolled asthma. Methods: We engaged stakeholders (caregivers, physicians, nurses, administrators) from six EDs in a three-phase process to: define design requirements; prototype and refine; and evaluate. Results: Interviews among 28 stakeholders yielded themes regarding in-home asthma management practices and ED discharge experiences. Quantitative and qualitative evaluation showed strong preference for the new discharge tool over current tools. Conclusion: Engaging end-users in contextual inquiry resulted in CAPE (CHICAGO Action Plan after ED discharge), a new stakeholder-balanced discharge tool, which is being tested in a multicenter comparative effectiveness trial. PMID:26690579

  11. Integrating physically based simulators with Event Detection Systems: Multi-site detection approach.

    PubMed

    Housh, Mashor; Ohar, Ziv

    2017-03-01

    The Fault Detection (FD) Problem in control theory concerns of monitoring a system to identify when a fault has occurred. Two approaches can be distinguished for the FD: Signal processing based FD and Model-based FD. The former concerns of developing algorithms to directly infer faults from sensors' readings, while the latter uses a simulation model of the real-system to analyze the discrepancy between sensors' readings and expected values from the simulation model. Most contamination Event Detection Systems (EDSs) for water distribution systems have followed the signal processing based FD, which relies on analyzing the signals from monitoring stations independently of each other, rather than evaluating all stations simultaneously within an integrated network. In this study, we show that a model-based EDS which utilizes a physically based water quality and hydraulics simulation models, can outperform the signal processing based EDS. We also show that the model-based EDS can facilitate the development of a Multi-Site EDS (MSEDS), which analyzes the data from all the monitoring stations simultaneously within an integrated network. The advantage of the joint analysis in the MSEDS is expressed by increased detection accuracy (higher true positive alarms and fewer false alarms) and shorter detection time. Copyright © 2016 Elsevier Ltd. All rights reserved.

  12. Electrodialytic 2-compartment cells for emerging organic contaminants removal from effluent.

    PubMed

    Ferreira, Ana Rita; Couto, Nazaré; Guedes, Paula; Pinto, Joana; Mateus, Eduardo P; Ribeiro, Alexandra B

    2018-04-27

    The present work discusses the efficiency of the electrodialytic (ED) process to remove emerging organic contaminants (EOCs) from effluent. The ED process was carried out in a cell of two-compartments (2 C-cell) with effluent in either the anode or cathode compartment, separated from the electrolyte compartment through an anion or a cation exchange membrane (AEM and CEM, respectively). As effluent destination might be soil irrigation, and having in mind the nutrient recycling, phosphorus was also monitored in the process. The ED removals showed to be dependent of EOCs characteristics and cell design. Removals were higher when using an AEM (60-72%) than a CEM (8-63%), except for caffeine when the effluent was placed in the cathode, that did not show any removal. When using an AEM with the effluent placed in the anode compartment, all the EOCs (including caffeine) were removed between 57-72%, mainly through electrodegradation phenomena. Regarding phosphorus, a polarity switch may be done to a 2 C-cell with a AEM, depending on the effluent final use. This technology is still in its first steps and, in both cases, further optimization of ED parameters is needed. Still, this technological innovation and cross-cutting research envisages the promotion of economic, social and environmental benefits. Copyright © 2018 Elsevier B.V. All rights reserved.

  13. People, Process, and Policy: Case Studies in National Security Advising, the National Security Council, and Presidential Decision Making

    DTIC Science & Technology

    2017-06-01

    processes. Rothkopf, David J. 2006. Running the World: The Inside Story of The National Security Council and The Architects of American Power . 1st ed...recognized Soviet aims. They aimed to gain power , spread communism, and counter the West. Eisenhower’s belief in American physical and ideological...The Architects of American Power . 1st ed. New York: Public Affairs: 322-324. 22 Burke, Honest Broker?, 341. 23 U.N. Ambassador Albright, Treasury

  14. Albizia lebbeck seed methanolic extract as a complementary therapy to manage local toxicity of Echis carinatus venom in a murine model.

    PubMed

    Amog, P U; Manjuprasanna, V N; Yariswamy, M; Nanjaraj Urs, A N; Joshi, Vikram; Suvilesh, K N; Nataraju, A; Vishwanath, Bannikuppe Sannanaik; Gowda, T V

    2016-11-01

    Viperid venom-induced chronic local-toxicity continues even after anti-snake venom treatment. Therefore, traditional antidote Albizia lebbeck L. (Fabaceae) seed extract was tested against Echis carinatus S. (Viperidae) venom (ECV)-induced local toxicity to evaluate its complementary remedy. Soxhlet extraction of A. lebbeck seeds was performed with the increasing polarity of solvents (n-hexane to water); the extract was screened for phytochemicals (alkaloids, anthraquinones, flavonoids, glycosides, phenolics, saponins, steroids and tannins). In preliminary in vitro analysis, A. lebbeck methanolic extract (ALME) demonstrated significant inhibition of ECV proteases, the major enzyme-toxin responsible for local- toxicity. Therefore, in vitro neutralizing potential of ALME was further evaluated against hyaluronidases and phospholipase A 2 (1:1-1:100 w/w). In addition, alleviation of ECV induced characteristic local- toxicity [haemorrhage (i.d.) and myotoxicity (i.m.)] was determined in mice. ALME contained high concentrations of phenolics and flavonoids and demonstrated significant in vitro inhibition of ECV protease (IC 50  =   36.32 μg, p < 0.0001) and hyaluronidase (IC 50  =   91.95 μg, p < 0.0001) at 1:100 w/w. ALME significantly neutralized ECV induced haemorrhage (ED 50  =   26.37 μg, p < 0.0001) and myotoxicity by significantly reducing serum creatinine kinase (ED 50  =   37.5 μg, p < 0.0001) and lactate dehydrogenase (ED 50  =   31.44 μg, p = 0.0021) levels at 1:50 w/w. ALME demonstrated significant neutralization of ECV enzymes that contribute in local tissue damage and haemostatic alterations. The study scientifically supports the anecdotal use of A. lebbeck in complementary medicine and identifies ALME as principle fraction responsible for antivenom properties.

  15. Enhanced bulk heterojunction devices prepared by thermal and solvent vapor annealing processes

    DOEpatents

    Forrest, Stephen R.; Thompson, Mark E.; Wei, Guodan; Wang, Siyi

    2017-09-19

    A method of preparing a bulk heterojunction organic photovoltaic cell through combinations of thermal and solvent vapor annealing are described. Bulk heterojunction films may prepared by known methods such as spin coating, and then exposed to one or more vaporized solvents and thermally annealed in an effort to enhance the crystalline nature of the photoactive materials.

  16. Green ultrasound-assisted extraction of carotenoids based on the bio-refinery concept using sunflower oil as an alternative solvent.

    PubMed

    Li, Ying; Fabiano-Tixier, Anne Sylvie; Tomao, Valérie; Cravotto, Giancarlo; Chemat, Farid

    2013-01-01

    A green, inexpensive and easy-to-use method for carotenoids extraction from fresh carrots assisted by ultrasound was designed in this work. Sunflower oil was applied as a substitute to organic solvents in this green ultrasound-assisted extraction (UAE): a process which is in line with green extraction and bio-refinery concepts. The processing procedure of this original UAE was first compared with conventional solvent extraction (CSE) using hexane as solvent. Moreover, the UAE optimal conditions for the subsequent comparison were optimized using response surface methodology (RSM) and ultra performance liquid chromatography--diode array detector--mass spectroscopy (UPLC-DAD-MS). The results showed that the UAE using sunflower as solvent has obtained its highest β-carotene yield (334.75 mg/l) in 20 min only, while CSE using hexane as solvent obtained a similar yield (321.35 mg/l) in 60 min. The green UAE performed under optimal extraction conditions (carrot to oil ratio of 2:10, ultrasonic intensity of 22.5 W cm(-2), temperature of 40 °C and sonication time of 20 min) gave the best yield of β-carotene. Copyright © 2012 Elsevier B.V. All rights reserved.

  17. Novel Low-Melt Viscosity Polyimides for Resin Transfer Molding (RTM)

    DTIC Science & Technology

    2008-08-29

    used no solvent in the process and the only volatile generated is water tbrmed during the imidization process. Resins were prepared as outlined below...without the use of a solvent. Due to the commercial availabilit \\ of 3,4’ -ODA, RTM370 is cheaper to manufacture than RTM 350 or RTM330. All these rcsins

  18. Development of a process for the extraction of {sup 137}Cs from acidic HLLW based on crown-calix extractant use of di-alkylamide modifier

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Alexova, J.; Sirova, M.; Rais, J.

    2008-07-01

    Within the framework of the ARTIST project of total fuel retreatment with ecological mixtures of solvents and extractants containing only C, H, O, and N atoms, a process segment of extraction of {sup 137}Cs from acidic stream was developed. The process with 25,27-Bis(1-octyloxy)calix[4]arene-crown- 6, DOC[4]C6, dissolved at its 0.01 M concentration in a mixture of 90 vol % 1-octanol and 10% dihexyl octanamide, DHOA was proposed as a viable variant due to its good multicycle performance, even with irradiated solvent, and due to the good chemical stability of the chosen combination of solvent mixture. (authors)

  19. Process for controlling morphology and improving thermal-mechanical performance of high performance interpenetrating and semi-interpenetrating polymer networks

    NASA Technical Reports Server (NTRS)

    Pater, Ruth H. (Inventor); Hansen, Marion G. (Inventor)

    1997-01-01

    In the process of the present invention, a non-polar, aprotic solvent is removed from an oligomer/polymer solution by freeze-drying in order to produce IPNs and semi-IPNs. By thermally quenching the solution to a solid in a short length of time, the size of the minor constituent-rich regions is greatly reduced as they are excluded along with the major constituent from the regions of crystallizing solvent. The use of this process sequence of controlling phase morphology provides IPNs and semi-IPNs with improved fracture toughness, microcracking resistance, and other physical-mechanical properties as compared to IPNs and semi-IPNs formed when the solvent is evaporated rather than sublimed.

  20. Process for controlling morphology and improving thermal mechanical performance of high performance interpenetrating and semiinterpenetrating polymer networks

    NASA Technical Reports Server (NTRS)

    Pater, Ruth H. (Inventor); Hansen, Marion G. (Inventor)

    1998-01-01

    In the process of the present invention, a non-polar, aprotic solvent is removed from an oligomer/polymer solution by freeze-drying in order to produce IPNs and semi-IPNs. By thermally quenching the solution to a solid in a short length of time, the size of the minor constituent-rich regions is greatly reduced as they are excluded along with the major constituent from the regions of crystallizing solvent. The use of this process sequence of controlling phase morphology provides IPNs and semi-IPNs with improved fracture toughness, microcracking resistance, and other physical-mechanical properties as compared to IPNs and semi-IPNs formed when the solvent is evaporated rather than sublimed.

  1. Process for producing an activated carbon adsorbent with integral heat transfer apparatus

    NASA Technical Reports Server (NTRS)

    Jones, Jack A. (Inventor); Yavrouian, Andre H. (Inventor)

    1996-01-01

    A process for producing an integral adsorbent-heat exchanger apparatus useful in ammonia refrigerant heat pump systems. In one embodiment, the process wets an activated carbon particles-solvent mixture with a binder-solvent mixture, presses the binder wetted activated carbon mixture on a metal tube surface and thereafter pyrolyzes the mixture to form a bonded activated carbon matrix adjoined to the tube surface. The integral apparatus can be easily and inexpensively produced by the process in large quantities.

  2. HAZ-ED Classroom Activities for Understanding Hazardous Waste.

    ERIC Educational Resources Information Center

    Environmental Protection Agency, Washington, DC.

    The Federal Superfund Program investigates and cleans up hazardous waste sites throughout the United States. Part of this program is devoted to informing the public and involving people in the process of cleaning up hazardous waste sites from beginning to end. The Haz-Ed program was developed to assist the Environmental Protection Agency's (EPA)…

  3. The External Contingencies and Development Processes of Students with Emotional Disabilities

    ERIC Educational Resources Information Center

    Nikolaros, John

    2015-01-01

    This paper examines the external contingencies that students with emotional disabilities (ED) experience throughout childhood and adolescence. It presents an in-depth assessment of the impact of external dynamics on the emotional development of students with ED, and considers the school, home, and community support systems. The paper assesses…

  4. Emergency department operations dictionary: results of the second performance measures and benchmarking summit.

    PubMed

    Welch, Shari J; Stone-Griffith, Suzanne; Asplin, Brent; Davidson, Steven J; Augustine, James; Schuur, Jeremiah D

    2011-05-01

    The public, payers, hospitals, and Centers for Medicare and Medicaid Services (CMS) are demanding that emergency departments (EDs) measure and improve performance, but this cannot be done unless we define the terms used in ED operations. On February 24, 2010, 32 stakeholders from 13 professional organizations met in Salt Lake City, Utah, to standardize ED operations metrics and definitions, which are presented in this consensus paper. Emergency medicine (EM) experts attending the Second Performance Measures and Benchmarking Summit reviewed, expanded, and updated key definitions for ED operations. Prior to the meeting, participants were provided with the definitions created at the first summit in 2006 and relevant documents from other organizations and asked to identify gaps and limitations in the original work. Those responses were used to devise a plan to revise and update the definitions. At the summit, attendees discussed and debated key terminology, and workgroups were created to draft a more comprehensive document. These results have been crafted into two reference documents, one for metrics and the operations dictionary presented here. The ED Operations Dictionary defines ED spaces, processes, patient populations, and new ED roles. Common definitions of key terms will improve the ability to compare ED operations research and practice and provide a common language for frontline practitioners, managers, and researchers. © 2011 by the Society for Academic Emergency Medicine.

  5. Building capacity in VA to provide emergency gynecology services for women.

    PubMed

    Cordasco, Kristina M; Huynh, Alexis K; Zephyrin, Laurie; Hamilton, Alison B; Lau-Herzberg, Amy E; Kessler, Chad S; Yano, Elizabeth M

    2015-04-01

    Visits to Veterans Administration (VA) emergency departments (EDs) are increasingly being made by women. A 2011 national inventory of VA emergency services for women revealed that many EDs have gaps in their resources and processes for gynecologic emergency care. To guide VA in addressing these gaps, we sought to understand factors acting as facilitators and/or barriers to improving VA ED capacity for, and quality of, emergency gynecology care. Semistructured interviews with VA emergency and women's health key informants. ED directors/providers (n=14), ED nurse managers (n=13), and Women Veteran Program Managers (n=13) in 13 VA facilities. Leadership, staff, space, demand, funding, policies, and community were noted as important factors influencing VA EDs building capacity and improving emergency gynecologic care for women Veterans. These factors are intertwined and cross multiple organizational levels so that each ED's capacity is a reflection not only of its own factors, but also those of its local medical center and non-VA community context as well as VA regional and national trends and policies. Policies and quality improvement initiatives aimed at building VA's emergency gynecologic services for women need to be multifactorial and aimed at multiple organizational levels. Policies need to be flexible to account for wide variations across EDs and their medical center and community contexts. Approaches that build and encourage local leadership engagement, such as evidence-based quality improvement methodology, are likely to be most effective.

  6. Protein-style dynamical transition in a non-biological polymer and a non-aqueous solvent

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Mamontov, E.; Sharma, V. K.; Borreguero, J. M.

    Using neutron scattering and molecular dynamics simulation, techniques most often associated with protein dynamical transition studies, we have investigated the microscopic dynamics of one of the most common polymers, polystyrene, which was exposed to toluene vapor, mimicking the process of protein hydration from water vapor. Polystyrene with adsorbed toluene is an example of a solvent-solute system, which, unlike biopolymers, is anhydrous and lacks hydrogen bonding. Nevertheless, it exhibits the essential traits of the dynamical transition in biomolecules, such as a specific dependence of the microscopic dynamics of both solvent and host on the temperature and the amount of solvent adsorbed.more » Ultimately, we conclude that the protein dynamical transition is a manifestation of a universal solvent-solute dynamical relationship, which is not specific to either biomolecules as solute, or aqueous media as solvent, or even a particular type of interactions between solvent and solute.« less

  7. Protein-style dynamical transition in a non-biological polymer and a non-aqueous solvent

    DOE PAGES

    Mamontov, E.; Sharma, V. K.; Borreguero, J. M.; ...

    2016-03-15

    Using neutron scattering and molecular dynamics simulation, techniques most often associated with protein dynamical transition studies, we have investigated the microscopic dynamics of one of the most common polymers, polystyrene, which was exposed to toluene vapor, mimicking the process of protein hydration from water vapor. Polystyrene with adsorbed toluene is an example of a solvent-solute system, which, unlike biopolymers, is anhydrous and lacks hydrogen bonding. Nevertheless, it exhibits the essential traits of the dynamical transition in biomolecules, such as a specific dependence of the microscopic dynamics of both solvent and host on the temperature and the amount of solvent adsorbed.more » Ultimately, we conclude that the protein dynamical transition is a manifestation of a universal solvent-solute dynamical relationship, which is not specific to either biomolecules as solute, or aqueous media as solvent, or even a particular type of interactions between solvent and solute.« less

  8. Measurement of dielectric constant of organic solvents by indigenously developed dielectric probe

    NASA Astrophysics Data System (ADS)

    Keshari, Ajay Kumar; Rao, J. Prabhakar; Rao, C. V. S. Brahmmananda; Ramakrishnan, R.; Ramanarayanan, R. R.

    2018-04-01

    The extraction, separation and purification of actinides (uranium and plutonium) from various matrices are an important step in nuclear fuel cycle. One of the separation process adopted in an industrial scale is the liquid-liquid extraction or solvent extraction. Liquid-liquid extraction uses a specific ligand/extractant in conjunction with suitable diluent. Solvent extraction or liquid-liquid extraction, involves the partitioning of the solute between two immiscible phases. In most cases, one of the phases is aqueous, and the other one is an organic solvent. The solvent used in solvent extraction should be selective for the metal of interest, it should have optimum distribution ratio, and the loaded metal from the organic phase should be easily stripped under suitable experimental conditions. Some of the important physical properties which are important for the solvent are density, viscosity, phase separation time, interfacial surface tension and the polarity of the extractant.

  9. Method for destroying halocarbon compositions using a critical solvent

    DOEpatents

    Ginosar, Daniel M.; Fox, Robert V.; Janikowski, Stuart K.

    2006-01-10

    A method for destroying halocarbons. Halocarbon materials are reacted in a dehalogenation process wherein they are combined with a solvent in the presence of a catalyst. A hydrogen-containing solvent is preferred which functions as both a solvating agent and hydrogen donor. To augment the hydrogen donation capacity of the solvent if needed (or when non-hydrogen-containing solvents are used), a supplemental hydrogen donor composition may be employed. In operation, at least one of the temperature and pressure of the solvent is maintained near, at, or above a critical level. For example, the solvent may be in (1) a supercritical state; (2) a state where one of the temperature or pressure thereof is at or above critical; or (3) a state where at least one of the temperature and pressure thereof is near-critical. This system provides numerous benefits including improved reaction rates, efficiency, and versatility.

  10. A thermodynamic study of complexation process between N, N'-dipyridoxylidene(1,4-butanediamine) and Cd2+ in some binary mixed solvents using conductometry

    NASA Astrophysics Data System (ADS)

    Ebrahimpoor, Sonia; Khoshnood, Razieh Sanavi; Beyramabadi, S. Ali

    2016-12-01

    Complexation of the Cd2+ ion with N, N'-dipyridoxylidene(1,4-butanediamine) Schiff base was studied in pure solvents including acetonitrile (AN), ethanol (EtOH), methanol (MeOH), tetrahydrofuran (THF), dimethylformamide (DMF), water (H2O), and various binary solvent mixtures of acetonitrile-ethanol (AN-EtOH), acetonitrile-methanol (AN-MeOH), acetonitrile-tetrahydrofuran (AN-THF), acetonitrile-dimethylformamide (AN-DMF), and acetonitrile-water (AN-H2O) systems at different temperatures using the conductometric method. The conductance data show that the stoichiometry of complex is 1: 1 [ML] in all solvent systems. A non-linear behavior was observed for changes of log K f of [Cd( N, N'-dipyridoxylidene(1,4-butanediamine)] complex versus the composition of the binary mixed solvents, which was explained in terms of solvent-solvent interactions. The results show that the thermodynamics of complexation reaction is affected by the nature and composition of the mixed solvents.

  11. EXPEDITIOUS SYNTHETIC TRANSFORMATIONS USING MICROWAVES

    EPA Science Inventory

    Microwave-expedited solvent-free synthetic processes will be described for the synthesis of a variety of industrially significant compounds and intermediates namely, enamines, nitroalkenes, enones, oxidized sulfur compounds and ionic liquids. This solvent-free synthetic methodolo...

  12. Integration of ceramic membrane and compressed air-assisted solvent extraction (CASX) for metal recovery.

    PubMed

    Li, Chi-Wang; Chiu, Chun-Hao; Lee, Yu-Cheng; Chang, Chia-Hao; Lee, Yu-Hsun; Chen, Yi-Ming

    2010-01-01

    In our previous publications, compressed air-assisted solvent extraction process (CASX) was developed and proved to be kinetically efficient process for metal removal. In the current study, CASX with a ceramic MF membrane integrated for separation of spent solvent was employed to remove and recover metal from wastewater. MF was operated either in crossflow mode or dead-end with intermittent flushing mode. Under crossflow mode, three distinct stages of flux vs. TMP (trans-membrane pressure) relationship were observed. In the first stage, flux increases with increasing TMP which is followed by the stage of stable flux with increasing TMP. After reaching a threshold TMP which is dependent of crossflow velocity, flux increases again with increasing TMP. At the last stage, solvent was pushed through membrane pores as indicated by increasing permeate COD. In dead-end with intermittent flushing mode, an intermittent flushing flow (2 min after a 10-min or a 30-min dead-end filtration) was incorporated to reduce membrane fouling by flush out MSAB accumulated on membrane surface. Effects of solvent concentration and composition were also investigated. Solvent concentrations ranging from 0.1 to 1% (w/w) have no adverse effect in terms of membrane fouling. However, solvent composition, i.e. D(2)EHPA/kerosene ratio, shows impact on membrane fouling. The type of metal extractants employed in CASX has significant impact on both membrane fouling and the quality of filtrate due to the differences in their viscosity and water solubility. Separation of MSAB was the limiting process controlling metal removal efficiency, and the removal efficiency of Cd(II) and Cr(VI) followed the same trend as that for COD.

  13. Effects of high-pressure process on kinetics of leaching oil from soybean powder using hexane in batch systems.

    PubMed

    Uhm, Joo Tae; Yoon, Won Byong

    2011-08-01

    Mass transfer models of leaching oil from soybean (Glycine max) flour with hexane after high-pressure process (HPP) treatment were developed. High pressure (450 MPa) was applied to the soybean flour (mean diameter of flour particle: 365 μm) for 30 min before leaching the oil components in the solvent. The ratio of solvent (volume, mL) to soybean flour (mass, g), such as 1:10 and 1:20, was employed to characterize the effect of solvent ratio on the leaching rate in the batch type of extraction process. Ultraviolet absorbance at 300 nm was used to monitor the extraction rate. Saturation solubility (C(AS)) was determined to be 21.73 kg/m³. The mass transfer coefficients (k) were determined based on the 1st- and 2nd-order kinetic models. The 2nd kinetic model showed better fit. The HPP treatment showed a higher extraction rate and yield compared to the control, while the amount of solvent did not affect the extraction rate and yield. The scanning electron microscope showed that HPP-treated soybean particles included more pores than the untreated. The pores observed in the HPP-treated soybean flours might help increase the mass transfer rate of solvent and solute in the solid matrix. High-pressure processing can help increase the extraction rate of oil from the soybean flour operated in batch systems. The conventional solid to solvent ratio (1:20) used to extract oil composition from the plant seed did not help increase the amount of oil extracted from the soybean flour. © 2011 Institute of Food Technologists®

  14. Is the relationship between cigarette smoking and male erectile dysfunction independent of cardiovascular disease? Findings from a population-based cross-sectional study.

    PubMed

    Chew, Kew-Kim; Bremner, Alexandra; Stuckey, Bronwyn; Earle, Carolyn; Jamrozik, Konrad

    2009-01-01

    Cigarette smoking has been implicated in the pathophysiology of cardiovascular disease (CVD) and as a risk factor for erectile dysfunction (ED). However, various aspects of the associations between cigarette smoking, ED, and CVD need further elucidation. We explored the relationship between cigarette smoking, ED, and CVD using data from a population-based cross-sectional study of 1,580 participants. Postal questionnaires were sent to randomly selected age-stratified male population samples obtained from the Western Australia Electoral Roll. In addition to items covering sociodemographic and self-reported clinical information and smoking habits, the 5-item International Index of Erectile Function was used to assess erectile function. Compared with never smokers, the odds of ED, adjusted for age, square of age, and CVD, were significantly higher among current smokers (odds ratio [OR] = 1.40; 95% confidence interval [CI] 1.02, 1.92) and ever smokers (OR = 1.57; 95% CI 1.02, 2.42). Similarly, the adjusted odds of severe ED were significantly higher among former smokers. Albeit not statistically significant, the age-adjusted odds of ED among current smokers increased with the number of cigarettes smoked. Among former smokers, the age-adjusted odds of ED were significantly higher 6-10 years following cessation of smoking than < or = 5 or > 10 years. Compared with never smokers without CVD, the age-adjusted odds of ED among former smokers and ever smokers without CVD were about 1.6. Regardless of smoking, these odds were significantly higher among participants with CVD. Compared with never smokers, former smokers and ever smokers have significantly higher odds of ED. The relationship between smoking and ED is independent of that between smoking and CVD, and not because of confounding by CVD. Patterns of ED in former smokers suggest that there may be a latent interval between active smoking and symptomatic ED, involving a process initially triggered by smoking.

  15. Efficient production of fatty acid methyl ester from waste activated bleaching earth using diesel oil as organic solvent.

    PubMed

    Kojima, Seiji; Du, Dongning; Sato, Masayasu; Park, Enoch Y

    2004-01-01

    Fatty acid methyl ester (FAME) production from waste activated bleaching earth (ABE) discarded by the crude oil refining industry was investigated using fossil fuel as a solvent in the esterification of triglycerides. Lipase from Candida cylindracea showed the highest stability in diesel oil. Using diesel oil as a solvent, 3 h was sufficient to obtain a yield of approximately 100% of FAME in the presence of 10% lipase from waste ABE. Kerosene was also a good solvent in the esterification of triglycerides embedded in the waste ABE. Fuel analysis showed that the FAME produced using diesel oil as a solvent complied with the Japanese diesel standard and the 10% residual carbon amount was lower than that of FAME produced using other solvents. Use of diesel oil as solvent in the FAME production from the waste ABE simplified the process, because there was no need to separate the organic solvent from the FAME-solvent mixture. These results demonstrate a promising reutilization method for the production of FAME, for use as a biodiesel, from industrial waste resources containing waste vegetable oils.

  16. Effects of Solvent Composition on Liquid Range, Glass Transition, and Conductivity of Electrolytes of a (Li, Cs)PF 6 Salt in EC-PC-EMC Solvents

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Ding, Michael S.; Li, Qiuyan; Li, Xing

    Electrolytes of 1 M LiPF 6 (lithium hexafluorophosphate) and 0.05 M CsPF 6 (cesium hexafluorophosphate) in EC-PC-EMC (ethylene carbonate-propylene carbonate-ethyl methyl carbonate) solvents of varying solvent compositions were studied for the effects of solvent composition on the lower limit of liquid range, viscosity (as reflected by the glass transition temperature), and electrolytic conductivity. In addition, a ternary phase diagram of EC-PC-EMC was constructed and crystallization temperatures of EC and EMC were calculated to assist the interpretation and understanding of the change of liquid range with solvent composition. A function based on Vogel-Fulcher-Tammann equation was fitted to the conductivity data inmore » their entirety and plotted as conductivity surfaces in solvent composition space for more direct and clear comparisons and discussions. Changes of viscosity and dielectric constant of the solvents with their composition, in relation to those of the solvent components, were found to be underlying many of the processes studied.« less

  17. A biocompatible tissue scaffold produced by supercritical fluid processing for cartilage tissue engineering.

    PubMed

    Kim, Su Hee; Jung, Youngmee; Kim, Soo Hyun

    2013-03-01

    Supercritical fluids are used in various industrial fields, such as the food and medical industries, because they have beneficial physical and chemical properties and are also nonflammable and inexpensive. In particular, supercritical carbon dioxide (ScCO(2)) is attractive due to its mild critical temperature, pressure values, and nontoxicity. Poly(L-lactide-co-ɛ-caprolactone) (PLCL), which is a biocompatible, biodegradable, and very elastic polymer, has been used in cartilage tissue engineering. However, organic solvents, such as chloroform or dichloromethane, are usually used for the fabrication of a PLCL scaffold through conventional methods. This leads to a cytotoxic effect and long processing time for removing solvents. To alleviate these problems, supercritical fluid processing is introduced here. In this study, we fabricated a mechano-active PLCL scaffold by supercritical fluid processing for cartilage tissue engineering, and we compared it with a scaffold made by a conventional solvent-casting method in terms of physical and biological performance. Also, to examine the optimum condition for preparing scaffolds with ScCO(2), we investigated the effects of pressure, temperature, and the depressurization rate on PLCL foaming. The PLCL scaffolds produced by supercritical fluid processing had a homogeneously interconnected porous structure, and they exhibited a narrow pore size distribution. Also, there was no cytotoxicity of the scaffolds made with ScCO(2) compared to the scaffolds made by the solvent-pressing method. The scaffolds were seeded with chondrocytes, and they were subcutaneously implanted into nude mice for up to 4 weeks. In vivo accumulation of extracellular matrix of cell-scaffold constructs demonstrated that the PLCL scaffold made with ScCO(2) formed a mature and well-developed cartilaginous tissue compared to the PLCL scaffold formed by solvent pressing. Consequently, these results indicated that the PLCL scaffolds made by supercritical fluid processing offer well-interconnected and nontoxic substrates for cell growth, avoiding problems associated with a solvent residue. This suggests that these elastic PLCL scaffolds formed by supercritical fluid processing could be used for cartilage tissue engineering.

  18. Emergency Department Expansion Versus Patient Flow Improvement: Impact on Patient Experience of Care.

    PubMed

    Sayah, Assaad; Lai-Becker, Melisa; Kingsley-Rocker, Lisa; Scott-Long, Tasha; O'Connor, Kelly; Lobon, Luis F

    2016-02-01

    Most strategies used to help improve the patient experience of care and ease emergency department (ED) crowding and diversion require additional space and personnel resources, major process improvement interventions, or a combination of both. To compare the impact of ED expansion vs. patient flow improvement and the establishment of a rapid assessment unit (RAU) on the patient experience of care in a medium-size safety net ED. This paper describes a study of a single ED wherein the department first undertook a physical expansion (2006 Q2 to 2007 Q2) followed by a reorganization of patient flow and establishment of an RAU (2009 Q2) by the use of an interrupted time series analysis. In the time period after ED expansion, significant negative trends were observed: decreasing Press Ganey percentiles (-4.1 percentile per quarter), increasing door-to-provider time (+4.9 minutes per quarter), increasing duration of stay (+13.2 minutes per quarter), and increasing percent of patients leaving without being seen (+0.11 per quarter). After the RAU was established, significant immediate impacts were observed for door-to-provider time (-25.8 minutes) and total duration of stay (-66.8 minutes). The trends for these indicators further suggested the improvements continued to be significant over time. Furthermore, the negative trends for the Press Ganey outcomes observed after ED expansion were significantly reversed and in the positive direction after the RAU. Our results demonstrate that the impact of process improvement and rapid assessment implementation is far greater than the impact of renovation and facility expansion. Copyright © 2016 Elsevier Inc. All rights reserved.

  19. Sequential Processing for Organic Photovoltaics: Design Rules for Morphology Control by Tailored Semi-Orthogonal Solvent Blends

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Aguirre, Jordan C.; Hawks, Steven A.; Ferreira, Amy S.

    2015-03-18

    Design rules are presented for significantly expanding sequential processing (SqP) into previously inaccessible polymer:fullerene systems by tailoring binary solvent blends for fullerene deposition. Starting with a base solvent that has high fullerene solubility, 2-chlorophenol (2-CP), ellipsometry-based swelling experiments are used to investigate different co-solvents for the fullerene-casting solution. By tuning the Flory-Huggins χ parameter of the 2-CP/co-solvent blend, it is possible to optimally swell the polymer of interest for fullerene interdiffusion without dissolution of the polymer underlayer. In this way solar cell power conversion efficiencies are obtained for the PTB7 (poly[(4,8-bis[(2-ethylhexyl)oxy]benzo[1,2-b:4,5-b']dithiophene-2,6-diyl)(3-fluoro-2-[(2-ethylhexyl)carbonyl]thieno[3,4-b]thiophenediyl)]) and PC61BM (phenyl-C61-butyric acid methyl ester) materials combination thatmore » match those of blend-cast films. Both semicrystalline (e.g., P3HT (poly(3-hexylthiophene-2,5-diyl)) and entirely amorphous (e.g., PSDTTT (poly[(4,8-di(2-butyloxy)benzo[1,2-b:4,5-b']dithiophene-2,6-diyl)-alt-(2,5-bis(4,4'-bis(2-octyl)dithieno[3,2-b:2'3'-d]silole-2,6-diyl)thiazolo[5,4-d]thiazole)]) conjugated polymers can be processed into highly efficient photovoltaic devices using the solvent-blend SqP design rules. Grazing-incidence wide-angle x-ray diffraction experiments confirm that proper choice of the fullerene casting co-solvent yields well-ordered interdispersed bulk heterojunction (BHJ) morphologies without the need for subsequent thermal annealing or the use of trace solvent additives (e.g., diiodooctane). The results open SqP to polymer/fullerene systems that are currently incompatible with traditional methods of device fabrication, and make BHJ morphology control a more tractable problem.« less

  20. Direct local solvent probing by transient infrared spectroscopy reveals the mechanism of hydrogen-bond induced nonradiative deactivation† †Electronic supplementary information (ESI) available: Experimental details, basic photophysics of ADA, transient electronic absorption, additional steady-state and transient IR spectra. See DOI: 10.1039/c7sc00437k Click here for additional data file.

    PubMed Central

    Dereka, Bogdan

    2017-01-01

    The fluorescence quenching of organic dyes via H-bonding interactions is a well-known phenomenon. However, the mechanism of this Hydrogen-Bond Induced Nonradiative Deactivation (HBIND) is not understood. Insight into this process is obtained by probing in the infrared the O–H stretching vibration of the solvent after electronic excitation of a dye with H-bond accepting cyano groups. The fluorescence lifetime of this dye was previously found to decrease from 1.5 ns to 110 ps when going from an aprotic solvent to the strongly protic hexafluoroisopropanol (HFP). Prompt strengthening of the H-bond with the dye was identified by the presence of a broad positive O–H band of HFP, located at lower frequency than the O–H band of the pure solvent. Further strengthening occurs within a few picoseconds before the excited H-bonded complex decays to the ground state in 110 ps. The latter process is accompanied by the dissipation of energy from the dye to the solvent and the rise of a characteristic hot solvent band in the transient spectrum. Polarization-resolved measurements evidence a collinear alignment of the nitrile and hydroxyl groups in the H-bonded complex, which persists during the whole excited-state lifetime. Measurements in other fluorinated alcohols and in chloroform/HFP mixtures reveal that the HBIND efficiency depends not only on the strength of the H-bond interactions between the dye and the solvent but also on the ability of the solvent to form an extended H-bond network. The HBIND process can be viewed as an enhanced internal conversion of an excited complex consisting of the dye molecule connected to a large H-bond network. PMID:28970892

Some links on this page may take you to non-federal websites. Their policies may differ from this site.
Top