ATMOSPHERIC AEROSOL SOURCE-RECEPTOR RELATIONSHIPS: THE ROLE OF COAL-FIRED POWER PLANTS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Allen L. Robinson; Spyros N. Pandis; Cliff I. Davidson

2004-12-01

This report describes the technical progress made on the Pittsburgh Air Quality Study (PAQS) during the period of March 2004 through August 2004. Significant progress was made this project period on the analysis of ambient data, source apportionment, and deterministic modeling activities. Results highlighted in this report include evaluation of the performance of PMCAMx+ for an air pollution episode in the Eastern US, an emission profile for a coke production facility, ultrafine particle composition during a nucleation event, and a new hybrid approach for source apportionment. An agreement was reached with a utility to characterize fine particle and mercury emissionsmore » from a commercial coal fired power. Research in the next project period will include source testing of a coal fired power plant, source apportionment analysis, emission scenario modeling with PMCAMx+, and writing up results for submission as journal articles.« less

PM SOURCE APPORTIONMENT/RECEPTOR MODELING

EPA Science Inventory

Source apportionment (receptor) models are mathematical procedures for identifying and quantifying the sources of ambient air pollutants and their effects at a site (the receptor), primarily on the basis of species concentration measurements at the receptor, and generally without...

Comparison of source apportionments of PM2.5 using three receptor models (CMB, PMF, and SMP) in Seoul, Korea

NASA Astrophysics Data System (ADS)

Heo, J.; Kim, J. Y.; Kim, S. W.

2017-12-01

We compared source apportionments of PM2.5 in Seoul, Korea by three receptor models, Chemical Mass Balance (CMB), Positive Matrix Factorization (PMF), and Solver for Mixture Problem (SMP). The CMB model can estimate source apportionment with suitable source profiles of emissions, but it is difficult to find location-specific source profiles. In contrary, the multivariate receptor model does not need source profiles, but fundamental natural physical constraints (FNPCs) required for aerosol source apportionment are different in PMF and SMP. Ninety-six PM2.5 daily samples collected at Korea Institute of Science and Technology (KIST) in Seoul, Korea from October 2012 to September 2013 were analyzed in this study. The average PM2.5 mass concentration over the study period was 41.5 ± 27.7 mg m-3 and secondary inorganic species and organic matter were the main chemical species occupying about 73.7% - 87.9% of the PM2.5 mass concentration in all seasons. Secondary sulfate (18.0% - 26.1%), secondary nitrate (12.1% - 28.5%), vehicle (2.9% - 32.9%), biomass burning (13.2% - 21.3%) were identified by all three receptor models as the major sources accounting for approximately 76.3%-82.7% of the total PM2.5 and contributions of main sources represented their seasonality. However, three receptor models showed significant differences, especially for vehicle emission due to their measured/estimated source profiles. In this presentation, more detailed comparisons among CMB, PMF and SMP models will be presented focusing on the source profiles and contributions.

Proceedings from the Workshop on Research Needs for Assessment and Management of Non-Point Air Emissions from Department of Defense Activities held in Research Triangle Park, North Carolina on 19-21 February 2008

DTIC Science & Technology

2008-10-01

Chow, J.C. (2006). Feasibility of soil dust source apportionment by the pyrolysis-gas chromatography/mass spectrometry method. J. Air Waste Manage...receptor-oriented source apportionment models. • Develop monitoring methods to determine source and fence line amounts of fugitive dust emissions for...offsite impact, including evaluation with receptor- oriented source apportionment models 76 8.8.1 Background 76 8.8.2 Significance 77 8.8.3

Photochemical grid model implementation and application of VOC, NOx, and O3 source apportionment

EPA Science Inventory

For the purposes of developing optimal emissions control strategies, efficient approaches are needed to identify the major sources or groups of sources that contribute to elevated ozone (O3) concentrations. Source-based apportionment techniques implemented in photochemical grid m...

Fine Particle Sources and Cardiorespiratory Morbidity: An Application of Chemical Mass Balance and Factor Analytical Source-Apportionment Methods

PubMed Central

Sarnat, Jeremy A.; Marmur, Amit; Klein, Mitchel; Kim, Eugene; Russell, Armistead G.; Sarnat, Stefanie E.; Mulholland, James A.; Hopke, Philip K.; Tolbert, Paige E.

2008-01-01

Background Interest in the health effects of particulate matter (PM) has focused on identifying sources of PM, including biomass burning, power plants, and gasoline and diesel emissions that may be associated with adverse health risks. Few epidemiologic studies, however, have included source-apportionment estimates in their examinations of PM health effects. We analyzed a time-series of chemically speciated PM measurements in Atlanta, Georgia, and conducted an epidemiologic analysis using data from three distinct source-apportionment methods. Objective The key objective of this analysis was to compare epidemiologic findings generated using both factor analysis and mass balance source-apportionment methods. Methods We analyzed data collected between November 1998 and December 2002 using positive-matrix factorization (PMF), modified chemical mass balance (CMB-LGO), and a tracer approach. Emergency department (ED) visits for a combined cardiovascular (CVD) and respiratory disease (RD) group were assessed as end points. We estimated the risk ratio (RR) associated with same day PM concentrations using Poisson generalized linear models. Results There were significant, positive associations between same-day PM2.5 (PM with aero-dynamic diameter ≤ 2.5 μm) concentrations attributed to mobile sources (RR range, 1.018–1.025) and biomass combustion, primarily prescribed forest burning and residential wood combustion, (RR range, 1.024–1.033) source categories and CVD-related ED visits. Associations between the source categories and RD visits were not significant for all models except sulfate-rich secondary PM2.5 (RR range, 1.012–1.020). Generally, the epidemiologic results were robust to the selection of source-apportionment method, with strong agreement between the RR estimates from the PMF and CMB-LGO models, as well as with results from models using single-species tracers as surrogates of the source-apportioned PM2.5 values. Conclusions Despite differences among the source-apportionment methods, these findings suggest that modeled source-apportioned data can produce robust estimates of acute health risk. In Atlanta, there were consistent associations across methods between PM2.5 from mobile sources and biomass burning with both cardiovascular and respiratory ED visits, and between sulfate-rich secondary PM2.5 with respiratory visits. PMID:18414627

SOURCE APPORTIONMENT OF EXPOSURES TO VOLATILE ORGANIC COMPOUNDS: I. EVALUATION OF RECEPTOR MODELS USING SIMULATED EXPOSURE DATA. (R826788)

EPA Science Inventory

Four receptor-oriented source apportionment models were evaluated by applying them to simulated personal exposure data for select volatile organic compounds (VOCs) that were generated by Monte Carlo sampling from known source contributions and profiles. The exposure sources mo...

DEVELOPMENT AND EVALUATION OF PM 2.5 SOURCE APPORTIONMENT METHODOLOGIES

EPA Science Inventory

The receptor model called Positive Matrix Factorization (PMF) has been extensively used to apportion sources of ambient fine particulate matter (PM_2.5), but the accuracy of source apportionment results currently remains unknown. In addition, air quality forecast model...

An integrated approach to assess heavy metal source apportionment in peri-urban agricultural soils.

PubMed

Huang, Ying; Li, Tingqiang; Wu, Chengxian; He, Zhenli; Japenga, Jan; Deng, Meihua; Yang, Xiaoe

2015-12-15

Three techniques (Isotope Ratio Analysis, GIS mapping, and Multivariate Statistical Analysis) were integrated to assess heavy metal pollution and source apportionment in peri-urban agricultural soils. The soils in the study area were moderately polluted with cadmium (Cd) and mercury (Hg), lightly polluted with lead (Pb), and chromium (Cr). GIS Mapping suggested Cd pollution originates from point sources, whereas Hg, Pb, Cr could be traced back to both point and non-point sources. Principal component analysis (PCA) indicated aluminum (Al), manganese (Mn), nickel (Ni) were mainly inherited from natural sources, while Hg, Pb, and Cd were associated with two different kinds of anthropogenic sources. Cluster analysis (CA) further identified fertilizers, waste water, industrial solid wastes, road dust, and atmospheric deposition as potential sources. Based on isotope ratio analysis (IRA) organic fertilizers and road dusts accounted for 74-100% and 0-24% of the total Hg input, while road dusts and solid wastes contributed for 0-80% and 19-100% of the Pb input. This study provides a reliable approach for heavy metal source apportionment in this particular peri-urban area, with a clear potential for future application in other regions. Copyright © 2015 Elsevier B.V. All rights reserved.

Source Apportionment Using Positive Matrix Factorization on Daily Measurements of Inorganic and Organic Speciated PM2.5

PubMed Central

Dutton, Steven J.; Vedal, Sverre; Piedrahita, Ricardo; Milford, Jana B.; Miller, Shelly L.; Hannigan, Michael P.

2012-01-01

Particulate matter less than 2.5 microns in diameter (PM2.5) has been linked with a wide range of adverse health effects. Determination of the sources of PM2.5 most responsible for these health effects could lead to improved understanding of the mechanisms of such effects and more targeted regulation. This has provided the impetus for the Denver Aerosol Sources and Health (DASH) study, a multi-year source apportionment and health effects study relying on detailed inorganic and organic PM2.5 speciation measurements. In this study, PM2.5 source apportionment is performed by coupling positive matrix factorization (PMF) with daily speciated PM2.5 measurements including inorganic ions, elemental carbon (EC) and organic carbon (OC), and organic molecular markers. A qualitative comparison is made between two models, PMF2 and ME2, commonly used for solving the PMF problem. Many previous studies have incorporated chemical mass balance (CMB) for organic molecular marker source apportionment on limited data sets, but the DASH data set is large enough to use multivariate factor analysis techniques such as PMF. Sensitivity of the PMF2 and ME2 models to the selection of speciated PM2.5 components and model input parameters was investigated in depth. A combination of diagnostics was used to select an optimum, 7-factor model using one complete year of daily data with pointwise measurement uncertainties. The factors included 1) a wintertime/methoxyphenol factor, 2) an EC/sterane factor, 3) a nitrate/polycyclic aromatic hydrocarbon (PAH) factor, 4) a summertime/selective aliphatic factor, 5) an n-alkane factor, 6) a middle oxygenated PAH/alkanoic acid factor and 7) an inorganic ion factor. These seven factors were qualitatively linked with known PM2.5 emission sources with varying degrees of confidence. Mass apportionment using the 7-factor model revealed the contribution of each factor to the mass of OC, EC, nitrate and sulfate. On an annual basis, the majority of OC and EC mass was associated with the summertime/selective aliphatic factor and the EC/sterane factor, respectively, while nitrate and sulfate mass were both dominated by the inorganic ion factor. This apportionment was found to vary substantially by season. Several of the factors identified in this study agree well with similar assessments conducted in St. Louis, MO and Pittsburgh, PA using PMF and organic molecular markers. PMID:22768005

77 FR 11974 - Approval and Promulgation of Implementation Plans; State of Iowa Regional Haze State...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-28

... and beyond. The modeling was based on PM Source Apportionment Technology (PSAT) for the Comprehensive... sources and the State adequately determined the apportionment of those pollutants from sources located... Class I areas caused by emissions of air pollutants from numerous sources located over a wide geographic...

Enterococcus and Escherichia coli fecal source apportionment with microbial source tracking genetic markers - is it feasible?

EPA Science Inventory

Fecal pollution is measured in surface waters using culture-based measurements of enterococci and Escherichia coli bacteria. Source apportionment of these two fecal indicator bacteria is an urgent need for prioritizing remediation efforts and quantifying health risks associated...

Trends in PM2.5 emissions, concentrations and apportionments in Detroit and Chicago

NASA Astrophysics Data System (ADS)

Milando, Chad; Huang, Lei; Batterman, Stuart

2016-03-01

PM2.5 concentrations throughout much of the U.S. have decreased over the last 15 years, but emissions and concentration trends can vary by location and source type. Such trends should be understood to inform air quality management and policies. This work examines trends in emissions, concentrations and source apportionments in two large Midwest U.S. cities, Detroit, Michigan, and Chicago, Illinois. Annual and seasonal trends were investigated using National Emission Inventory (NEI) data for 2002 to 2011, speciated ambient PM2.5 data from 2001 to 2014, apportionments from positive matrix factorization (PMF) receptor modeling, and quantile regression. Over the study period, county-wide data suggest emissions from point sources decreased (Detroit) or held constant (Chicago), while emissions from on-road mobile sources were constant (Detroit) or increased (Chicago), however changes in methodology limit the interpretation of inventory trends. Ambient concentration data also suggest source and apportionment trends, e.g., annual median concentrations of PM2.5 in the two cities declined by 3.2-3.6%/yr (faster than national trends), and sulfate concentrations (due to coal-fired facilities and other point source emissions) declined even faster; in contrast, organic and elemental carbon (tracers of gasoline and diesel vehicle exhaust) declined more slowly or held constant. The PMF models identified nine sources in Detroit and eight in Chicago, the most important being secondary sulfate, secondary nitrate and vehicle emissions. A minor crustal dust source, metals sources, and a biomass source also were present in both cities. These apportionments showed that the median relative contributions from secondary sulfate sources decreased by 4.2-5.5% per year in Detroit and Chicago, while contributions from metals sources, biomass sources, and vehicles increased from 1.3 to 9.2% per year. This first application of quantile regression to trend analyses of speciated PM2.5 data reveals that source contributions to PM2.5 varied as PM2.5 concentrations decreased, and that the fraction of PM2.5 due to emissions from vehicles and other local emissions has increased. Each data source has uncertainties, but emissions, monitoring and PMF data provide complementary information that can help to discern trends and identify contributing sources. Study results emphasize the need to target specific sources in policies and regulations aimed at decreasing PM2.5 concentrations in urban areas.

A Handbook for Determining the Sources of PCB Contamination in Sediments

DTIC Science & Technology

2012-10-01

identifying sources for initial source control to later use for remedial cost apportionment . Often, forensic investigations are successfully used to...alteration processes, source apportionment can be difficult. For instance, one can easily imagine an onshore spill or source of PCB oil that results in a...the use of Aroclor analyses for identifying contamination sources to only fresh samples (for example, PCB oils or soils with freshly spilled PCB

A modified receptor model for source apportionment of heavy metal pollution in soil.

PubMed

Huang, Ying; Deng, Meihua; Wu, Shaofu; Japenga, Jan; Li, Tingqiang; Yang, Xiaoe; He, Zhenli

2018-07-15

Source apportionment is a crucial step toward reduction of heavy metal pollution in soil. Existing methods are generally based on receptor models. However, overestimation or underestimation occurs when they are applied to heavy metal source apportionment in soil. Therefore, a modified model (PCA-MLRD) was developed, which is based on principal component analysis (PCA) and multiple linear regression with distance (MLRD). This model was applied to a case study conducted in a peri-urban area in southeast China where soils were contaminated by arsenic (As), cadmium (Cd), mercury (Hg) and lead (Pb). Compared with existing models, PCA-MLRD is able to identify specific sources and quantify the extent of influence for each emission. The zinc (Zn)-Pb mine was identified as the most important anthropogenic emission, which affected approximately half area for Pb and As accumulation, and approximately one third for Cd. Overall, the influence extent of the anthropogenic emissions decreased in the order of mine (3 km) > dyeing mill (2 km) ≈ industrial hub (2 km) > fluorescent factory (1.5 km) > road (0.5 km). Although algorithm still needs to improved, the PCA-MLRD model has the potential to become a useful tool for heavy metal source apportionment in soil. Copyright © 2018 Elsevier B.V. All rights reserved.

Source Apportionment of PM2.5 in Delhi, India Using PMF Model.

PubMed

Sharma, S K; Mandal, T K; Jain, Srishti; Saraswati; Sharma, A; Saxena, Mohit

2016-08-01

Chemical characterization of PM2.5 [organic carbon, elemental carbon, water soluble inorganic ionic components, and major and trace elements] was carried out for a source apportionment study of PM2.5 at an urban site of Delhi, India from January, 2013, to December, 2014. The annual average mass concentration of PM2.5 was 122 ± 94.1 µg m(-3). Strong seasonal variation was observed in PM2.5 mass concentration and its chemical composition with maxima during winter and minima during monsoon. A receptor model, positive matrix factorization (PMF) was applied for source apportionment of PM2.5 mass concentration. The PMF model resolved the major sources of PM2.5 as secondary aerosols (21.3 %), followed by soil dust (20.5 %), vehicle emissions (19.7 %), biomass burning (14.3 %), fossil fuel combustion (13.7 %), industrial emissions (6.2 %) and sea salt (4.3 %).

Guidance Document for PMF Applications with the Multilinear Engine

EPA Science Inventory

This document serves as a guide for users of the Multilinear Engine version 2 (ME-2) for source apportionment applications utilizing positive matrix factorization (PMF). It aims to educate experienced source apportionment analysts on available ME rotational tools and provides gui...

Source apportionment of PM2.5 organic carbon in the San Joaquin Valley using monthly and daily observations and meteorological clustering.

PubMed

Skiles, Matthew J; Lai, Alexandra M; Olson, Michael R; Schauer, James J; de Foy, Benjamin

2018-06-01

Two hundred sixty-three fine particulate matter (PM 2.5 ) samples collected on 3-day intervals over a 14-month period at two sites in the San Joaquin Valley (SJV) were analyzed for organic carbon (OC), elemental carbon (EC), water soluble organic carbon (WSOC), and organic molecular markers. A unique source profile library was applied to a chemical mass balance (CMB) source apportionment model to develop monthly and seasonally averaged source apportionment results. Five major OC sources were identified: mobile sources, biomass burning, meat smoke, vegetative detritus, and secondary organic carbon (SOC), as inferred from OC not apportioned by CMB. The SOC factor was the largest source contributor at Fresno and Bakersfield, contributing 44% and 51% of PM mass, respectively. Biomass burning was the only source with a statistically different average mass contribution (95% CI) between the two sites. Wintertime peaks of biomass burning, meat smoke, and total OC were observed at both sites, with SOC peaking during the summer months. Exceptionally strong seasonal variation in apportioned meat smoke mass could potentially be explained by oxidation of cholesterol between source and receptor and trends in wind transport outlined in a Residence Time Analysis (RTA). Fast moving nighttime winds prevalent during warmer months caused local emissions to be replaced by air mass transported from the San Francisco Bay Area, consisting of mostly diluted, oxidized concentrations of molecular markers. Good agreement was observed between SOC derived from the CMB model and from non-biomass burning WSOC mass, suggesting the CMB model is sufficiently accurate to assist in policy development. In general, uncertainty in monthly mass values derived from daily CMB apportionments were lower than that of CMB results produced with monthly marker composites, further validating daily sampling methodologies. Strong seasonal trends were observed for biomass and meat smoke OC apportionment, and monthly mass averages had lowest uncertainty when derived from daily CMB apportionments. Copyright © 2018 Elsevier Ltd. All rights reserved.

Contamination source apportionment and health risk assessment of heavy metals in soil around municipal solid waste incinerator: A case study in North China.

PubMed

Ma, Wenchao; Tai, Lingyu; Qiao, Zhi; Zhong, Lei; Wang, Zhen; Fu, Kaixuan; Chen, Guanyi

2018-08-01

Few studies have comprehensively taken into account the source apportionment and human health risk of soil heavy metals in the vicinity of municipal solid waste incinerator (MSWI) in high population density area. In this study, 8 elements (Cr, Pb, Cu, Ni, Zn, Cd, Hg, and As) in fly ash, soil samples from different functional areas and vegetables collected surrounding the MSWI in North China were determined. The single pollution index, integrated Nemerow pollution index, principal component analysis (PCA), absolute principle component score-multiple linear regression (APCS-MLR) model and dose-response model were used in this study. The results showed that the soils around the MSWI were moderately polluted by Cu, Pb, Zn, and Hg, and heavily polluted by As and Cd. MSWI had a significant influence on the distribution of soil heavy metals in different distances from MSWI. The source apportionment results showed that MSWI, natural source, industrial discharges and coal combustion were the four major potential sources for heavy metals in the soils, with the contributions of 36.08%, 29.57%, 10.07%, and 4.55%, respectively. MSWI had a major impact on Zn, Cu, Pb, Cd, and Hg contamination in soil. The non-carcinogenic risk and carcinogenic risk posed by soil heavy metals surrounding the MSWI were unacceptable. The soil heavy metals concentrations and health risks in different functional areas were distinct. MSWI was the predominate source of non-carcinogenic risk with the average contribution rate of 36.99% and carcinogenic risk to adult male, adult female and children with 4.23×10 -4 , 4.57×10 -4 , and 1.41×10 -4 respectively, implying that the impact of MSWI on human health was apparent. This study provided a new insight for the source apportionment and health risk assessment of soil heavy metals in the vicinity of MSWI. Copyright © 2018. Published by Elsevier B.V.

A clustering algorithm for sample data based on environmental pollution characteristics

NASA Astrophysics Data System (ADS)

Chen, Mei; Wang, Pengfei; Chen, Qiang; Wu, Jiadong; Chen, Xiaoyun

2015-04-01

Environmental pollution has become an issue of serious international concern in recent years. Among the receptor-oriented pollution models, CMB, PMF, UNMIX, and PCA are widely used as source apportionment models. To improve the accuracy of source apportionment and classify the sample data for these models, this study proposes an easy-to-use, high-dimensional EPC algorithm that not only organizes all of the sample data into different groups according to the similarities in pollution characteristics such as pollution sources and concentrations but also simultaneously detects outliers. The main clustering process consists of selecting the first unlabelled point as the cluster centre, then assigning each data point in the sample dataset to its most similar cluster centre according to both the user-defined threshold and the value of similarity function in each iteration, and finally modifying the clusters using a method similar to k-Means. The validity and accuracy of the algorithm are tested using both real and synthetic datasets, which makes the EPC algorithm practical and effective for appropriately classifying sample data for source apportionment models and helpful for better understanding and interpreting the sources of pollution.

Defense Coastal/Estuarine Research Program (DCERP) Strategic Plan

DTIC Science & Technology

2007-09-01

atmospheric deposition. The source apportionment of nutrients from atmospheric deposition (especially nitrogen) to estuarine waters derived from direct...migrating wildlife, and nutrient release from soil weathering, atmospheric deposition represents the only source of new nutrients into the... apportionment to properly assess the contributions of off-site and on-site emission sources to regional levels of PM2.5. In preparing this DCERP Strategic

Single particle characterization, source apportionment, and aging effects of ambient aerosols in Southern California

NASA Astrophysics Data System (ADS)

Shields, Laura Grace

Composed of a mixture of chemical species and phases and existing in a variety of shapes and sizes, atmospheric aerosols are complex and can have serious influence on human health, the environment, and climate. In order to better understand the impact of aerosols on local to global scales, detailed measurements on the physical and chemical properties of ambient particles are essential. In addition, knowing the origin or the source of the aerosols is important for policymakers to implement targeted regulations and effective control strategies to reduce air pollution in their region. One of the most ground breaking techniques in aerosol instrumentation is single particle mass spectrometry (SPMS), which can provide online chemical composition and size information on the individual particle level. The primary focus of this work is to further improve the ability of one specific SPMS technique, aerosol time-of-flight mass spectrometry (ATOFMS), for the use of identifying the specific origin of ambient aerosols, which is known as source apportionment. The ATOFMS source apportionment method utilizes a library of distinct source mass spectral signatures to match the chemical information of the single ambient particles. The unique signatures are obtained in controlled source characterization studies, such as with the exhaust emissions of heavy duty diesel vehicles (HDDV) operating on a dynamometer. The apportionment of ambient aerosols is complicated by the chemical and physical processes an individual particle can undergo as it spends time in the atmosphere, which is referred to as "aging" of the aerosol. Therefore, the performance of the source signature library technique was investigated on the ambient dataset of the highly aged environment of Riverside, California. Additionally, two specific subsets of the Riverside dataset (ultrafine particles and particles containing trace metals), which are known to cause adverse health effects, were probed in greater detail. Finally, the impact of large wildfires on the ambient levels of particulate matter in Southern California is discussed. The results of this work provide insight into single particles impacting the Southern California region, the relative source contributions to this region, and finally an examination of how atmospheric aging influences the ability to perform source apportionment.

Microbial water pollution: a screening tool for initial catchment-scale assessment and source apportionment.

PubMed

Kay, D; Anthony, S; Crowther, J; Chambers, B J; Nicholson, F A; Chadwick, D; Stapleton, C M; Wyer, M D

2010-11-01

The European Union Water Framework Directive requires that Management Plans are developed for individual River Basin Districts. From the point of view of faecal indicator organisms (FIOs), there is a critical need for screening tools that can provide a rapid assessment of the likely FIO concentrations and fluxes within catchments under base- and high-flow conditions, and of the balance ('source apportionment') between agriculture- and sewage-derived sources. Accordingly, the present paper reports on: (1) the development of preliminary generic models, using water quality and land cover data from previous UK catchment studies for assessing FIO concentrations, fluxes and source apportionment within catchments during the summer bathing season; (2) the calibration of national land use data, against data previously used in the models; and (3) provisional FIO concentration and source-apportionment assessments for England and Wales. The models clearly highlighted the crucial importance of high-flow conditions for the flux of FIOs within catchments. At high flow, improved grassland (and associated livestock) was the key FIO source; FIO loadings derived from catchments with high proportions of improved grassland were shown to be as high as from urbanized catchments; and in many rural catchments, especially in NW and SW England and Wales, which are important areas of lowland livestock (especially dairy) farming, ≥ 40% of FIOs was assessed to be derived from agricultural sources. In contrast, under base-flow conditions, when there was little or no runoff from agricultural land, urban (i.e. sewerage-related) sources were assessed to dominate, and even in rural areas the majority of FIOs were attributed to urban sources. The results of the study demonstrate the potential of this type of approach, particularly in light of climate change and the likelihood of more high-flow events, in underpinning informed policy development and prioritization of investment. Copyright © 2009 Elsevier B.V. All rights reserved.

Establishing the origin of particulate matter across Europe

NASA Astrophysics Data System (ADS)

Schaap, Martijn; Kranenburg, Richard; Hendriks, Carlijn; Kuenen, Jeroen

2016-04-01

Exposure to particulate matter (PM) in ambient air leads to adverse health effects. To design cost effective mitigation strategies, a thorough understanding of the sources of particulate matter is crucial. In this paper we like to provide an overview of recent source apportionment studies aimed at PM and its precursors carried out at TNO. The source apportionment module that tracks the origin of modelled particulate matter distributions throughout a LOTOS-EUROS simulation will be explained. To optimally apply this technology dedicated emission inventories, e.g. fuel type specific, need to be generated. Applications to Europe shows that in northwestern Europe the contribution of transport and agricultural emissions dominate the PM mass concentrations, especially during episodic events. In eastern Europe, the domestic and energy sector are much more important. In southern Europe the picture is more mixed, although the frequent high levels of desert dust stand out. Evaluation of the source allocation against experimental data and PMF analyses is challenging as there is only a limited availability of source specific tracers or factors that can be used for direct comparison. Nonetheless, for the available tracers such as vanadium for heavy fuel oil combustion an evaluation is very well possible. The source apportionment technique can also be used to interpret particulate matter formation efficiencies. It will be shown that the conversion rates for the secondary inorganic aerosol precursors (NOx, NH3 and SO2) have changed during the last 20 years. A particular problem is related to the fact that CTMs systematically underestimate observed PM levels, which means that the contribution of certain source categories (natural, agriculture, combustion) are underestimated. Future developments needed to improve the source apportionment information concerning process knowledge, data assimilation as well as model implementation will be discussed. Specific challenges concerning the underlying emission information will be highlighted.

An inter-comparison of PM10 source apportionment using PCA and PMF receptor models in three European sites.

PubMed

Cesari, Daniela; Amato, F; Pandolfi, M; Alastuey, A; Querol, X; Contini, D

2016-08-01

Source apportionment of aerosol is an important approach to investigate aerosol formation and transformation processes as well as to assess appropriate mitigation strategies and to investigate causes of non-compliance with air quality standards (Directive 2008/50/CE). Receptor models (RMs) based on chemical composition of aerosol measured at specific sites are a useful, and widely used, tool to perform source apportionment. However, an analysis of available studies in the scientific literature reveals heterogeneities in the approaches used, in terms of "working variables" such as the number of samples in the dataset and the number of chemical species used as well as in the modeling tools used. In this work, an inter-comparison of PM10 source apportionment results obtained at three European measurement sites is presented, using two receptor models: principal component analysis coupled with multi-linear regression analysis (PCA-MLRA) and positive matrix factorization (PMF). The inter-comparison focuses on source identification, quantification of source contribution to PM10, robustness of the results, and how these are influenced by the number of chemical species available in the datasets. Results show very similar component/factor profiles identified by PCA and PMF, with some discrepancies in the number of factors. The PMF model appears to be more suitable to separate secondary sulfate and secondary nitrate with respect to PCA at least in the datasets analyzed. Further, some difficulties have been observed with PCA in separating industrial and heavy oil combustion contributions. Commonly at all sites, the crustal contributions found with PCA were larger than those found with PMF, and the secondary inorganic aerosol contributions found by PCA were lower than those found by PMF. Site-dependent differences were also observed for traffic and marine contributions. The inter-comparison of source apportionment performed on complete datasets (using the full range of available chemical species) and incomplete datasets (with reduced number of chemical species) allowed to investigate the sensitivity of source apportionment (SA) results to the working variables used in the RMs. Results show that, at both sites, the profiles and the contributions of the different sources calculated with PMF are comparable within the estimated uncertainties indicating a good stability and robustness of PMF results. In contrast, PCA outputs are more sensitive to the chemical species present in the datasets. In PCA, the crustal contributions are higher in the incomplete datasets and the traffic contributions are significantly lower for incomplete datasets.

MOLECULAR MARKER ANALYSIS OF DEARS SAMPLES

EPA Science Inventory

Source apportionment based on organic molecular markers provides a promising approach for meeting the Detroit Exposure and Aerosol Research Study (DEARS) objective of comparing source contributions between community air monitoring stations and various neighborhoods. Source appor...

(ISEA) MOLECULAR MARKER ANALYSIS OF DEARS SAMPLES

EPA Science Inventory

Source apportionment based on organic molecular markers provides a promising approach for meeting the Detroit Exposure and Aerosol Research Study (DEARS) objective of comparing source contributions between community air monitoring stations and various neighborhoods. Source appor...

Combining emission inventory and isotope ratio analyses for quantitative source apportionment of heavy metals in agricultural soil.

PubMed

Chen, Lian; Zhou, Shenglu; Wu, Shaohua; Wang, Chunhui; Li, Baojie; Li, Yan; Wang, Junxiao

2018-08-01

Two quantitative methods (emission inventory and isotope ratio analysis) were combined to apportion source contributions of heavy metals entering agricultural soils in the Lihe River watershed (Taihu region, east China). Source apportionment based on the emission inventory method indicated that for Cd, Cr, Cu, Pb, and Zn, the mean percentage input from atmospheric deposition was highest (62-85%), followed by irrigation (12-27%) and fertilization (1-14%). Thus, the heavy metals were derived mainly from industrial activities and traffic emissions. For Ni the combined percentage input from irrigation and fertilization was approximately 20% higher than that from atmospheric deposition, indicating that Ni was mainly derived from agricultural activities. Based on isotope ratio analysis, atmospheric deposition accounted for 57-93% of Pb entering soil, with the mean value of 69.3%, which indicates that this was the major source of Pb entering soil in the study area. The mean contributions of irrigation and fertilization to Pb pollution of soil ranged from 0% to 10%, indicating that they played only a marginally important role. Overall, the results obtained using the two methods were similar. This study provides a reliable approach for source apportionment of heavy metals entering agricultural soils in the study area, and clearly have potential application for future studies in other regions. Copyright © 2018 Elsevier Ltd. All rights reserved.

Application of an integrated Weather Research and Forecasting (WRF)/CALPUFF modeling tool for source apportionment of atmospheric pollutants for air quality management: A case study in the urban area of Benxi, China.

PubMed

Wu, Hao; Zhang, Yan; Yu, Qi; Ma, Weichun

2018-04-01

In this study, the authors endeavored to develop an effective framework for improving local urban air quality on meso-micro scales in cities in China that are experiencing rapid urbanization. Within this framework, the integrated Weather Research and Forecasting (WRF)/CALPUFF modeling system was applied to simulate the concentration distributions of typical pollutants (particulate matter with an aerodynamic diameter <10 μm [PM 10 ], sulfur dioxide [SO 2 ], and nitrogen oxides [NO x ]) in the urban area of Benxi. Statistical analyses were performed to verify the credibility of this simulation, including the meteorological fields and concentration fields. The sources were then categorized using two different classification methods (the district-based and type-based methods), and the contributions to the pollutant concentrations from each source category were computed to provide a basis for appropriate control measures. The statistical indexes showed that CALMET had sufficient ability to predict the meteorological conditions, such as the wind fields and temperatures, which provided meteorological data for the subsequent CALPUFF run. The simulated concentrations from CALPUFF showed considerable agreement with the observed values but were generally underestimated. The spatial-temporal concentration pattern revealed that the maximum concentrations tended to appear in the urban centers and during the winter. In terms of their contributions to pollutant concentrations, the districts of Xihu, Pingshan, and Mingshan all affected the urban air quality to different degrees. According to the type-based classification, which categorized the pollution sources as belonging to the Bengang Group, large point sources, small point sources, and area sources, the source apportionment showed that the Bengang Group, the large point sources, and the area sources had considerable impacts on urban air quality. Finally, combined with the industrial characteristics, detailed control measures were proposed with which local policy makers could improve the urban air quality in Benxi. In summary, the results of this study showed that this framework has credibility for effectively improving urban air quality, based on the source apportionment of atmospheric pollutants. The authors endeavored to build up an effective framework based on the integrated WRF/CALPUFF to improve the air quality in many cities on meso-micro scales in China. Via this framework, the integrated modeling tool is accurately used to study the characteristics of meteorological fields, concentration fields, and source apportionments of pollutants in target area. The impacts of classified sources on air quality together with the industrial characteristics can provide more effective control measures for improving air quality. Through the case study, the technical framework developed in this study, particularly the source apportionment, could provide important data and technical support for policy makers to assess air pollution on the scale of a city in China or even the world.

[Preliminary study of source apportionment of PM10 and PM2.5 in three cities of China during spring].

PubMed

Gao, Shen; Pan, Xiao-chuan; Madaniyazi, Li-na; Xie, Juan; He, Ya-hui

2013-09-01

To study source apportionment of atmospheric PM10 (particle matter ≤ 10 µm in aerodynamic diameter) and PM2.5 (particle matter ≤ 2.5 µm in aerodynamic diameter) in Beijing,Urumqi and Qingdao, China. The atmospheric particle samples of PM10 and PM2.5 collected from Beijing between May 17th and June 18th, 2005, from Urumqi between April 20th and June 1st, 2006 and from Qingdao between April 4th and May 15th, 2005, were detected to trace the source apportionment by factor analysis and enrichment factor methods. In Beijing, the source apportionment results derived from factor analysis model for PM10 were construction dust and soil sand dust (contributing rate of variance at 45.35%), industry dust, coal-combusted smoke and vehicle emissions (contributing rate at 31.83%), and biomass burning dust (13.57%). The main pollution element was Pb, while the content (median (minimum value-maximum value)was 0.216 (0.040-0.795) µg/m(3)) . As for PM2.5, the sources were construction dust and soil sand dust (38.86%), industry dust, coal-combusted smoke and vehicle emissions (25.73%), biomass burning dust (13.10%) and burning oil dust (11.92%). The main pollution element was Zn (0.365(0.126-0.808) µg/m(3)).In Urumqi, source apportionment results for PM10 were soil sand dust and coal-combusted dust(49.75%), industry dust, vehicle emissions and secondary particles dust (30.65%). The main characteristic pollution element was Cd (0.463(0.033-1.351) ng/m(3)). As for PM2.5, the sources were soil sand dust and coal-combusted dust (43.26%), secondary particles dust (22.29%), industry dust and vehicle emissions (20.50%). The main characteristic pollution element was As (14.599 (1.696-36.741) µg/m(3)).In Qingdao, source apportionment results for PM10 were construction dust (30.91%), vehicle emissions and industry dust (29.65%) and secondary particles dust (28.99%). The main characteristic pollution element was Pb (64.071 (5.846-346.831) µg/m(3)). As for PM2.5, the sources were secondary particles dust, industry dust and vehicle emissions (49.82%) and construction dust (33.71%). The main characteristic pollution element was Pb(57.340 (5.004-241.559) µg/m(3)).Enrichment factors of Zn, Pb, As and Cd in PM2.5 were higher than those in PM10 both in Beijing and Urumqi. The major sources of the atmospheric particles PM10 and PM2.5 in Beijing were cement dust from construction sites and sand dust from soil; while the major sources of those in Urumqi were pollution by smoke and sand dust from burning coal. The major sources of the atmospheric particles PM10 in Qingdao were cement dust from construction sites; however, the major sources of PM2.5 there were secondary particles dust, industry dust and vehicle emissions. According to our study, the heavy metal elements were likely to gather in PM2.5.

Source apportionment of exposures to volatile organic compounds. I. Evaluation of receptor models using simulated exposure data

NASA Astrophysics Data System (ADS)

Miller, Shelly L.; Anderson, Melissa J.; Daly, Eileen P.; Milford, Jana B.

Four receptor-oriented source apportionment models were evaluated by applying them to simulated personal exposure data for select volatile organic compounds (VOCs) that were generated by Monte Carlo sampling from known source contributions and profiles. The exposure sources modeled are environmental tobacco smoke, paint emissions, cleaning and/or pesticide products, gasoline vapors, automobile exhaust, and wastewater treatment plant emissions. The receptor models analyzed are chemical mass balance, principal component analysis/absolute principal component scores, positive matrix factorization (PMF), and graphical ratio analysis for composition estimates/source apportionment by factors with explicit restriction, incorporated in the UNMIX model. All models identified only the major contributors to total exposure concentrations. PMF extracted factor profiles that most closely represented the major sources used to generate the simulated data. None of the models were able to distinguish between sources with similar chemical profiles. Sources that contributed <5% to the average total VOC exposure were not identified.

SOURCE APPORTIONMENT OF PM 2.5 AND CARBON IN SEATTLE USING CHEMICAL MASS BALANCE AND POSITIVE MATRIX FACTORIZATION

EPA Science Inventory

Three years of PM2.5 speciated data were collected and chemically analyzed using the IMPROVE protocol at the Beacon Hill site in Seattle. The data were analyzed by the Chemical Mass Balance Version 8 (CMB8) and Positive Matrix Factorization (PMF) source apportionment models. T...

Numerical simulations for the sources apportionment and control strategies of PM2.5 over Pearl River Delta, China, part I: Inventory and PM2.5 sources apportionment.

PubMed

Huang, Yeqi; Deng, Tao; Li, Zhenning; Wang, Nan; Yin, Chanqin; Wang, Shiqiang; Fan, Shaojia

2018-09-01

This article uses the WRF-CMAQ model to systematically study the source apportionment of PM 2.5 under typical meteorological conditions in the dry season (November 2010) in the Pearl River Delta (PRD). According to the geographical location and the relative magnitude of pollutant emission, Guangdong Province is divided into eight subdomains for source apportionment study. The Brute-Force Method (BFM) method was implemented to simulate the contribution from different regions to the PM 2.5 pollution in the PRD. Results show that the industrial sources accounted for the largest proportion. For emission species, the total amount of NO x and VOC in Guangdong Province, and NH 3 and VOC in Hunan Province are relatively larger. In Guangdong Province, the emission of SO 2 , NO x and VOC in the PRD are relatively larger, and the NH 3 emissions are higher outside the PRD. In northerly-controlled episodes, model simulations demonstrate that local emissions are important for PM 2.5 pollution in Guangzhou and Foshan. Meanwhile, emissions from Dongguan and Huizhou (DH), and out of Guangdong Province (SW) are important contributors for PM 2.5 pollution in Guangzhou. For PM 2.5 pollution in Foshan, emissions in Guangzhou and DH are the major contributors. In addition, high contribution ratio from DH only occurs in severe pollution periods. In southerly-controlled episode, contribution from the southern PRD increases. Local emissions and emissions from Shenzhen, DH, Zhuhai-Jiangmen-Zhongshan (ZJZ) are the major contributors. Regional contribution to the chemical compositions of PM 2.5 indicates that the sources of chemical components are similar to those of PM 2.5 . In particular, SO 4 2- is mainly sourced from emissions out of Guangdong Province, while the NO 3- and NH 4+ are more linked to agricultural emissions. Copyright © 2018 Elsevier B.V. All rights reserved.

Temporal trend and source apportionment of water pollution in different functional zones of Qiantang River, China.

PubMed

Su, Shiliang; Li, Dan; Zhang, Qi; Xiao, Rui; Huang, Fang; Wu, Jiaping

2011-02-01

The increasingly serious river water pollution in developing countries poses great threat to environmental health and human welfare. The assignment of river function to specific uses, known as zoning, is a useful tool to reveal variations of water environmental adaptability to human impact. Therefore, characterizing the temporal trend and identifying responsible pollution sources in different functional zones could greatly improve our knowledge about human impacts on the river water environment. The aim of this study is to obtain a deeper understanding of temporal trends and sources of water pollution in different functional zones with a case study of the Qiantang River, China. Measurement data were obtained and pretreated for 13 variables from 41 monitoring sites in four categories of functional zones during the period 1996-2004. An exploratory approach, which combines smoothing and non-parametric statistical tests, was applied to characterize trends of four significant parameters (permanganate index, ammonia nitrogen, total cadmium and fluoride) accounting for differences among different functional zones identified by discriminant analysis. Aided by GIS, yearly pollution index (PI) for each monitoring site was further mapped to compare the within-group variations in temporal dynamics for different functional zones. Rotated principal component analysis and receptor model (absolute principle component score-multiple linear regression, APCS-MLR) revealed that potential pollution sources and their corresponding contributions varied among the four functional zones. Variations of APCS values for each site of one functional zone as well as their annual average values highlighted the uncertainties associated with cross space-time effects in source apportionment. All these results reinforce the notion that the concept of zoning should be taken seriously in water pollution control. Being applicable to other rivers, the framework of management-oriented source apportionment is thus believed to have potentials to offer new insights into water management and advance the source apportionment framework as an operational basis for national and local governments. © 2010 Elsevier Ltd. All rights reserved.

Integrating Source Apportionment Tracers into a Bottom-up Inventory of Methane Emissions in the Barnett Shale Hydraulic Fracturing Region.

PubMed

Townsend-Small, Amy; Marrero, Josette E; Lyon, David R; Simpson, Isobel J; Meinardi, Simone; Blake, Donald R

2015-07-07

A growing dependence on natural gas for energy may exacerbate emissions of the greenhouse gas methane (CH4). Identifying fingerprints of these emissions is critical to our understanding of potential impacts. Here, we compare stable isotopic and alkane ratio tracers of natural gas, agricultural, and urban CH4 sources in the Barnett Shale hydraulic fracturing region near Fort Worth, Texas. Thermogenic and biogenic sources were compositionally distinct, and emissions from oil wells were enriched in alkanes and isotopically depleted relative to natural gas wells. Emissions from natural gas production varied in δ(13)C and alkane ratio composition, with δD-CH4 representing the most consistent tracer of natural gas sources. We integrated our data into a bottom-up inventory of CH4 for the region, resulting in an inventory of ethane (C2H6) sources for comparison to top-down estimates of CH4 and C2H6 emissions. Methane emissions in the Barnett are a complex mixture of urban, agricultural, and fossil fuel sources, which makes source apportionment challenging. For example, spatial heterogeneity in gas composition and high C2H6/CH4 ratios in emissions from conventional oil production add uncertainty to top-down models of source apportionment. Future top-down studies may benefit from the addition of δD-CH4 to distinguish thermogenic and biogenic sources.

Verifying Sediment Fingerprinting Results with Known Mixtures

NASA Astrophysics Data System (ADS)

Gellis, A.; Gorman-Sanisaca, L.; Cashman, M. J.

2017-12-01

Sediment fingerprinting is a widely used approach to determine the specific sources of fluvial sediment within a watershed. It relies on the principle that potential sediment sources can be identified using a set of chemical tracers (or fingerprints), and comparison of these source fingerprints with fluvial (target) sediment allows for source apportionment of the fluvial sediment. There are numerous source classifications, fingerprints, and statistical approaches used in the literature to apportion sources of sediment. However, few of these studies have sought to test the method by creating controls on the ratio of sources in the target sediment. Without a controlled environment for inputs and outputs, such verification of results is ambiguous. Here, we generated artificial mixtures of source sediment from an agricultural/forested watershed in Virginia, USA (Smith Creek, 246 km2) to verify the apportionment results. Target samples were established from known mixtures of the four major sediment sources in the watershed (forest, pasture, cropland, and streambanks). The target samples were sieved to less than 63 microns and analyzed for elemental and isotopic chemistry. The target samples and source samples were run through the Sediment Source Assessment Tool (Sed_SAT) to verify if the statistical operations provided the correct apportionment. Sed_SAT uses a multivariate parametric approach to identify the minimum suite of fingerprints that discriminate the source areas and applies these fingerprints through an unmixng model to apportion sediment. The results of this sediment fingerprinting verification experiment will be presented in this session.

Aerosol source apportionment based on multi-wavelength photoacoustic light absorption measurements: a simulation method for system's optimisation

NASA Astrophysics Data System (ADS)

Simon, Károly; Ajtai, Tibor; Kiss-Albert, Gergely; Utry, Noémi; Pintér, Máté; Szabó, Gábor; Bozóki, Zoltán

2017-04-01

Aerosol source apportionment is currently one of the outstanding challenges for environmental monitoring. In most cases atmospheric aerosol is a heterogeneous mixture as it typically originates from various sources. Consequently, each aerosol type has distinct chemical and physical properties. Contrary to chemical properties, optical absorption and size distribution of airborne particles can be measured in real time with high time resolution i.e. their measurement facilitates real time source apportionment (Favez et al (2009), Ajtai et al (2011), Favez et al (2010)). The wavelength dependency of the optical absorption coefficient (OAC) is usually characterised by the Absorption Angström Exponent (AAE). So far, the selection of light sources (lasers) into a photoacoustic aerosol measuring system was based on rule of thumb type estimations only. Recently, we proposed a simulation method that can be used to estimate the accuracy of aerosol source apportionment in case of a dual wavelength photoacoustic system (Simon et al., (2017)). This simulation is based on the assumption that the atmospheric aerosol load is dominated by two distinct sources and each of them is strongly light absorbing with specific AAE values. This is a typical scenario e.g. for urban measurements under wintry conditions when dominating aerosol sources are fossil fuel and wood burning with characteristic AAE 1 and 2, respectively. The wavelength pair of 405 and 1064 nm was found to be optimal for source apportionment in this case. In the presented study we investigated the situation when there are aerosol components with only slightly different AAE values and searched for a photoacoustic system which is optimal for distinguishing these components. Ajtai, T.; Filep, Á.; Utry, N.; Schnaiter, M.; Linke, C.; Bozóki, Z.; Szabó, G. and Leisner T. (2011) Journal of Aerosol Science 42, 859-866. Favez, O.; Cachier, H.; Sciare, J.; Sarda-Estève, R. and Martinon, L. (2009) Atmospheric Environment 43, 3640-3644. Favez, O.; El Haddad, I.; Piot, C.; Boréave, A.; Abidi, E.; Marchand, N.; Jaffrezo, J. L.; Besombes, J. L.; Personnaz, M. B.; Sciare, J.; Wortham, H.; George, C. and D'Anna, B. (2010), Atmos. Chem. Phys. 10, 5295-5314. Simon, K.A.; Ajtai, T; Gulyas, G; Utry, N; Pinter, M; Szabo, G. and Bozoki, Bozoki, Z. (2017), Journal of Aerosol Science 104, 10-15.

A Regional Assessment of Marine Vessel PM2.5 Impacts in the U.S. Pacific Northwest Using a Receptor Based Source Apportionment Method

EPA Science Inventory

This work reports the results of a regional receptor-based source apportionment analysis using the Positive Matrix Factorization (PMF) model on chemically speciated PM2.5 data from 36 urban and rural monitoring sites within the U.S. Pacific Northwest. The approach taken is to mo...

Weak acid extractable metals in Bramble Bay, Queensland, Australia: temporal behaviour, enrichment and source apportionment.

PubMed

Brady, James P; Ayoko, Godwin A; Martens, Wayde N; Goonetilleke, Ashantha

2015-02-15

Sediment samples were taken from six sampling sites in Bramble Bay, Queensland, Australia between February and November in 2012. They were analysed for a range of heavy metals including Al, Fe, Mn, Ti, Ce, Th, U, V, Cr, Co, Ni, Cu, Zn, As, Cd, Sb, Te, Hg, Tl and Pb. Fraction analysis, Enrichment Factors and Principal Component Analysis-Absolute Principal Component Scores (PCA-APCS) were carried out in order to assess metal pollution, potential bioavailability and source apportionment. Cr and Ni exceeded the Australian Interim Sediment Quality Guidelines at some sampling sites, while Hg was found to be the most enriched metal. Fraction analysis identified increased weak acid soluble Hg and Cd during the sampling period. Source apportionment via PCA-APCS found four sources of metals pollution, namely, marine sediments, shipping, antifouling coatings and a mixed source. These sources need to be considered in any metal pollution control measure within Bramble Bay. Copyright © 2014 Elsevier Ltd. All rights reserved.

Preliminary Results of the first European Source Apportionment intercomparison for Receptor and Chemical Transport Models

NASA Astrophysics Data System (ADS)

Belis, Claudio A.; Pernigotti, Denise; Pirovano, Guido

2017-04-01

Source Apportionment (SA) is the identification of ambient air pollution sources and the quantification of their contribution to pollution levels. This task can be accomplished using different approaches: chemical transport models and receptor models. Receptor models are derived from measurements and therefore are considered as a reference for primary sources urban background levels. Chemical transport model have better estimation of the secondary pollutants (inorganic) and are capable to provide gridded results with high time resolution. Assessing the performance of SA model results is essential to guarantee reliable information on source contributions to be used for the reporting to the Commission and in the development of pollution abatement strategies. This is the first intercomparison ever designed to test both receptor oriented models (or receptor models) and chemical transport models (or source oriented models) using a comprehensive method based on model quality indicators and pre-established criteria. The target pollutant of this exercise, organised in the frame of FAIRMODE WG 3, is PM10. Both receptor models and chemical transport models present good performances when evaluated against their respective references. Both types of models demonstrate quite satisfactory capabilities to estimate the yearly source contributions while the estimation of the source contributions at the daily level (time series) is more critical. Chemical transport models showed a tendency to underestimate the contribution of some single sources when compared to receptor models. For receptor models the most critical source category is industry. This is probably due to the variety of single sources with different characteristics that belong to this category. Dust is the most problematic source for Chemical Transport Models, likely due to the poor information about this kind of source in the emission inventories, particularly concerning road dust re-suspension, and consequently the little detail about the chemical components of this source used in the models. The sensitivity tests show that chemical transport models show better performances when displaying a detailed set of sources (14) than when using a simplified one (only 8). It was also observed that an enhanced vertical profiling can improve the estimation of specific sources, such as industry, under complex meteorological conditions and that an insufficient spatial resolution in urban areas can impact on the capabilities of models to estimate the contribution of diffuse primary sources (e.g. traffic). Both families of models identify traffic and biomass burning as the first and second most contributing categories, respectively, to elemental carbon. The results of this study demonstrate that the source apportionment assessment methodology developed by the JRC is applicable to any kind of SA model. The same methodology is implemented in the on-line DeltaSA tool to support source apportionment model evaluation (http://source-apportionment.jrc.ec.europa.eu/).

RECENT APPLICATIONS OF SOURCE APPORTIONMENT METHODS AND RELATED NEEDS

EPA Science Inventory

Traditional receptor modeling studies have utilized factor analysis (like principal component analysis, PCA) and/or Chemical Mass Balance (CMB) to assess source influences. The limitations with these approaches is that PCA is qualitative and CMB requires the input of source pr...

Organic aerosol components derived from 25 AMS datasets across Europe using a newly developed ME-2 based source apportionment strategy

NASA Astrophysics Data System (ADS)

Crippa, M.; Canonaco, F.; Lanz, V. A.; Äijälä, M.; Allan, J. D.; Carbone, S.; Capes, G.; Dall'Osto, M.; Day, D. A.; DeCarlo, P. F.; Di Marco, C. F.; Ehn, M.; Eriksson, A.; Freney, E.; Hildebrandt Ruiz, L.; Hillamo, R.; Jimenez, J.-L.; Junninen, H.; Kiendler-Scharr, A.; Kortelainen, A.-M.; Kulmala, M.; Mensah, A. A.; Mohr, C.; Nemitz, E.; O'Dowd, C.; Ovadnevaite, J.; Pandis, S. N.; Petäjä, T.; Poulain, L.; Saarikoski, S.; Sellegri, K.; Swietlicki, E.; Tiitta, P.; Worsnop, D. R.; Baltensperger, U.; Prévôt, A. S. H.

2013-09-01

Organic aerosols (OA) represent one of the major constituents of submicron particulate matter (PM1) and comprise a huge variety of compounds emitted by different sources. Three intensive measurement field campaigns to investigate the aerosol chemical composition all over Europe were carried out within the framework of EUCAARI and the intensive campaigns of EMEP during 2008 (May-June and September-October) and 2009 (February-March). In this paper we focus on the identification of the main organic aerosol sources and we propose a standardized methodology to perform source apportionment using positive matrix factorization (PMF) with the multilinear engine (ME-2) on Aerodyne aerosol mass spectrometer (AMS) data. Our source apportionment procedure is tested and applied on 25 datasets accounting for urban, rural, remote and high altitude sites and therefore it is likely suitable for the treatment of AMS-related ambient datasets. For most of the sites, four organic components are retrieved, improving significantly previous source apportionment results where only a separation in primary and secondary OA sources was possible. Our solutions include two primary OA sources, i.e. hydrocarbon-like OA (HOA) and biomass burning OA (BBOA) and two secondary OA components, i.e. semi-volatile oxygenated OA (SV-OOA) and low-volatility oxygenated OA (LV-OOA). For specific sites cooking-related (COA) and marine-related sources (MSA) are also separated. Finally, our work provides a large overview of organic aerosol sources in Europe and an interesting set of highly time resolved data for modeling evaluation purposes.

Source Apportionment of Elemental Carbon in Beijing, China: Insights from Radiocarbon and Organic Marker Measurements.

PubMed

Zhang, Yan-Lin; Schnelle-Kreis, Jürgen; Abbaszade, Gülcin; Zimmermann, Ralf; Zotter, Peter; Shen, Rong-rong; Schäfer, Klaus; Shao, Longyi; Prévôt, André S H; Szidat, Sönke

2015-07-21

Elemental carbon (EC) or black carbon (BC) in the atmosphere has a strong influence on both climate and human health. In this study, radiocarbon ((14)C) based source apportionment is used to distinguish between fossil fuel and biomass burning sources of EC isolated from aerosol filter samples collected in Beijing from June 2010 to May 2011. The (14)C results demonstrate that EC is consistently dominated by fossil-fuel combustion throughout the whole year with a mean contribution of 79% ± 6% (ranging from 70% to 91%), though EC has a higher mean and peak concentrations in the cold season. The seasonal molecular pattern of hopanes (i.e., a class of organic markers mainly emitted during the combustion of different fossil fuels) indicates that traffic-related emissions are the most important fossil source in the warm period and coal combustion emissions are significantly increased in the cold season. By combining (14)C based source apportionment results and picene (i.e., an organic marker for coal emissions) concentrations, relative contributions from coal (mainly from residential bituminous coal) and vehicle to EC in the cold period were estimated as 25 ± 4% and 50 ± 7%, respectively, whereas the coal combustion contribution was negligible or very small in the warm period.

26 CFR 1.861-8 - Computation of taxable income from sources within the United States and from other sources and...

Code of Federal Regulations, 2010 CFR

2010-04-01

... income. [Reserved]. For guidance, see § 1.861-8T(c)(1). (2) Apportionment based on assets. [Reserved.... [Reserved]. For guidance, see § 1.861-8T(d)(2). (e) Allocation and apportionment of certain deductions—(1... section. (2) Interest. [Reserved]. For guidance, see § 1.861-8T(e)(2). (3) Research and experimental...

SOURCE APPORTIONMENT OF FINE PARTICLES IN THE U.S. AND ASSOCIATIONS BETWEEN INFLAMMATORY MARKER IL -8

EPA Science Inventory

Associations are well established between particulate matter (PM) and increased human mortality and morbidity. The association between PM sources and inflammatory marker IL-8 was evaluated in this study.

PARTICLE SPECIATION AND EMISSION PROFILES OF SMALL 2-STROKE ENGINES

EPA Science Inventory

The Human Exposure and Atmospheric Sciences Division (HEASD) conducts studies designed to acquire information from emission sources for use in source apportionment studies. The objective of this work is to characterize a complete, speciated emission profile (PM and air toxics) ...

SOURCES OF MERCURY WET DEPOSITION IN EASTERN OHIO, USA

EPA Science Inventory

In the fall of 2002, an enhanced air monitoring site was established in Steubenville, Ohio as part of a multi-year comprehensive mercury monitoring and source apportionment study to investigate the impact of local and regional coal combustion sources on atmospheric mercury deposi...

Source apportionment of lead in the blood of women of reproductive age living near tailings in Taxco, Guerrero, Mexico: An isotopic study.

PubMed

Vázquez Bahéna, Analine Berenice; Talavera Mendoza, Oscar; Moreno Godínez, Ma Elena; Salgado Souto, Sergio Adrián; Ruiz, Joaquín; Huerta Beristain, Gerardo

2017-04-01

The concentration and isotopic composition of lead in the blood of forty seven women of reproductive age (15-45y) exposed to multiple sources in two rural communities of the mining region of Taxco, Guerrero in southern Mexico were determined in order to identify specific contributing sources and their apportionment and to trace probable ingestion pathways. Our data indicate that >36% of the studied women have blood lead concentrations above 10μgdL -1 and up to 87% above 5μgdL -1 . Tailings contain between 2128 and 5988mgkg -1 of lead and represent the most conspicuous source in the area. Lead contents in indoor dust are largely variable (21.7-987mgkg -1 ) but only 15% of samples are above the Mexican Regulatory Guideline for urban soils (400mgkg -1 ). By contrast, 85% of glazed containers (range: 0.026-68.6mgkg -1 ) used for cooking and food storage are above the maximum 2mgL -1 of soluble lead established in the Mexican Guideline. The isotopic composition indicates that lead in the blood of 95% of the studied women can be modeled in terms of a mixing system between local ores (and derivatives), glazed pottery and Morelos bedrock, end-members, with the two former being largely the most important contributors. Only one sample shows influence of indoor paints. Indoor dust is dominated by ores and derivatives but some samples show evidence of contribution from a less radiogenic source very likely represented by interior paints. This study supports the application of lead isotopic ratios to identify potential sources and their apportionment in humans exposed to multiple sources of lead from both, natural and anthropogenic origin. Copyright © 2017 Elsevier B.V. All rights reserved.

Characterization of emissions from South Asian biofuels and application to source apportionment of carbonaceous aerosol in the Himalayas

NASA Astrophysics Data System (ADS)

Stone, Elizabeth A.; Schauer, James J.; Pradhan, Bidya Banmali; Dangol, Pradeep Man; Habib, Gazala; Venkataraman, Chandra; Ramanathan, V.

2010-03-01

This study focuses on improving source apportionment of carbonaceous aerosol in South Asia and consists of three parts: (1) development of novel molecular marker-based profiles for real-world biofuel combustion, (2) application of these profiles to a year-long data set, and (3) evaluation of profiles by an in-depth sensitivity analysis. Emissions profiles for biomass fuels were developed through source testing of a residential stove commonly used in South Asia. Wood fuels were combusted at high and low rates, which corresponded to source profiles high in organic carbon (OC) or high in elemental carbon (EC), respectively. Crop wastes common to the region, including rice straw, mustard stalk, jute stalk, soybean stalk, and animal residue burnings, were also characterized. Biofuel profiles were used in a source apportionment study of OC and EC in Godavari, Nepal. This site is located in the foothills of the Himalayas and was selected for its well-mixed and regionally impacted air masses. At Godavari, daily samples of fine particulate matter (PM2.5) were collected throughout the year of 2006, and the annual trends in particulate mass, OC, and EC followed the occurrence of a regional haze in South Asia. Maximum concentrations occurred during the dry winter season and minimum concentrations occurred during the summer monsoon season. Specific organic compounds unique to aerosol sources, molecular markers, were measured in monthly composite samples. These markers implicated motor vehicles, coal combustion, biomass burning, cow dung burning, vegetative detritus, and secondary organic aerosol as sources of carbonaceous aerosol. A molecular marker-based chemical mass balance (CMB) model provided a quantitative assessment of primary source contributions to carbonaceous aerosol. The new profiles were compared to widely used biomass burning profiles from the literature in a sensitivity analysis. This analysis indicated a high degree of stability in estimates of source contributions to OC when different biomass profiles were used. The majority of OC was unapportioned to primary sources and was estimated to be of secondary origin, while biomass combustion was the next-largest source of OC. The CMB apportionment of EC to primary sources was unstable due to the diversity of biomass burning conditions in the region. The model results suggested that biomass burning and fossil fuel were important contributors to EC, but could not reconcile their relative contributions.

Coarse and fine aerosol source apportionment in Rio de Janeiro, Brazil

NASA Astrophysics Data System (ADS)

Godoy, Maria Luiza D. P.; Godoy, José Marcus; Roldão, Luiz Alfredo; Soluri, Daniela S.; Donagemma, Raquel A.

The metropolitan area of Rio de Janeiro is one of the twenty biggest urban agglomerations in the world, with 11 million inhabitants in the metropolitan area, and has a high population density, with 1700 hab. km -2. For this aerosol source apportionment study, the atmospheric aerosol sampling was performed at ten sites distributed in different locations of the metropolitan area from September/2003 to December/2005, with sampling during 24 h on a weekly basis. Stacked filter units (SFU) were used to collect fine and coarse aerosol particles with a flow rate of 17 L min -1. In both size fractions trace elements were analyzed by Inductively Coupled Plasma-Mass Spectrometry (ICP-MS) as well as water-soluble species by Ion-Chromatography (IC). Also gravimetric analysis and reflectance measurements provided aerosol mass and black carbon concentrations. Very good detection limits for up to 42 species were obtained. Mean annual PM 10 mass concentration ranged from 20 to 37 μg m -3, values that are within the Brazilian air quality standards. Receptor models such as principal factor analysis, cluster analysis and absolute principal factor analysis were applied in order to identify and quantify the aerosol sources. For fine and coarse modes, circa of 100% of the measured mass was quantitatively apportioned to relatively few identified aerosol sources. A very similar and consistent source apportionment was obtained for both fine and coarse modes for all 10 sampling sites. Soil dust is an important component, accounting for 22-72% and for 25-48% of the coarse and fine mass respectively. On the other hand, anthropogenic sources as vehicle traffic and oil combustion represent a relatively high contribution (52-75%) of the fine aerosol mass. The joint use of ICP-MS and IC analysis of species in aerosols has proven to be reliable and feasible for the analysis of large amount of samples, and the coupling with receptor models provided an excellent method for quantitative aerosol source apportionment in large urban areas.

Winter-time size distribution and source apportionment of total suspended particulate matter and associated metals in Delhi

NASA Astrophysics Data System (ADS)

Srivastava, Arun; Gupta, Sandeep; Jain, V. K.

2009-03-01

A study of the winter time size distribution and source apportionment of total suspended particulate matter (TSPM) and associated heavy metal concentrations have been carried out for the city of Delhi. This study is important from the point of view of implementation of compressed natural gas (CNG) as alternate of diesel fuel in the public transport system in 2001 to reduce the pollution level. TSPM were collected using a five-stage cascade impactor at six sites in the winters of 2005-06. The results of size distribution indicate that a major portion (~ 40%) of TSPM concentration is in the form of PM0.7 (< 0.7 μm). Similar trends were observed with most of the heavy metals associated with various size fractions of TSPM. A very good correlation between coarse and fine size fraction of TSPM was observed. It was also observed that the metals associated with coarse particles have more chances of correlation with other metals; rather they are associated with fine particles. Source apportionment was carried out separately in coarse and fine size modes of TSPM by Chemical Mass Balance Receptor Model (CMB8) as well as by Principle Component Analysis (PCA) of SPSS. Source apportionment by PCA reveals that there are two major sources (possibly vehicular and crustal re-suspension) in both coarse and fine size fractions. Results obtained by CMB8 show the dominance of vehicular pollutants and crustal dust in fine and coarse size mode respectively. Noticeably the dominance of vehicular pollutants are now confined to fine size only whilst during pre CNG era it dominated both coarse and fine size mode. An increase of 42.5, 44.4, 48.2, 38.6 and 38.9% in the concentrations of TSPM, PM10.9, coarse particles, fine particles and lead respectively was observed during pre (2001) to post CNG (2005-06) period.

Organic aerosol components derived from 25 AMS data sets across Europe using a consistent ME-2 based source apportionment approach

NASA Astrophysics Data System (ADS)

Crippa, M.; Canonaco, F.; Lanz, V. A.; Äijälä, M.; Allan, J. D.; Carbone, S.; Capes, G.; Ceburnis, D.; Dall'Osto, M.; Day, D. A.; DeCarlo, P. F.; Ehn, M.; Eriksson, A.; Freney, E.; Hildebrandt Ruiz, L.; Hillamo, R.; Jimenez, J. L.; Junninen, H.; Kiendler-Scharr, A.; Kortelainen, A.-M.; Kulmala, M.; Laaksonen, A.; Mensah, A. A.; Mohr, C.; Nemitz, E.; O'Dowd, C.; Ovadnevaite, J.; Pandis, S. N.; Petäjä, T.; Poulain, L.; Saarikoski, S.; Sellegri, K.; Swietlicki, E.; Tiitta, P.; Worsnop, D. R.; Baltensperger, U.; Prévôt, A. S. H.

2014-06-01

Organic aerosols (OA) represent one of the major constituents of submicron particulate matter (PM1) and comprise a huge variety of compounds emitted by different sources. Three intensive measurement field campaigns to investigate the aerosol chemical composition all over Europe were carried out within the framework of the European Integrated Project on Aerosol Cloud Climate and Air Quality Interactions (EUCAARI) and the intensive campaigns of European Monitoring and Evaluation Programme (EMEP) during 2008 (May-June and September-October) and 2009 (February-March). In this paper we focus on the identification of the main organic aerosol sources and we define a standardized methodology to perform source apportionment using positive matrix factorization (PMF) with the multilinear engine (ME-2) on Aerodyne aerosol mass spectrometer (AMS) data. Our source apportionment procedure is tested and applied on 25 data sets accounting for two urban, several rural and remote and two high altitude sites; therefore it is likely suitable for the treatment of AMS-related ambient data sets. For most of the sites, four organic components are retrieved, improving significantly previous source apportionment results where only a separation in primary and secondary OA sources was possible. Generally, our solutions include two primary OA sources, i.e. hydrocarbon-like OA (HOA) and biomass burning OA (BBOA) and two secondary OA components, i.e. semi-volatile oxygenated OA (SV-OOA) and low-volatility oxygenated OA (LV-OOA). For specific sites cooking-related (COA) and marine-related sources (MSA) are also separated. Finally, our work provides a large overview of organic aerosol sources in Europe and an interesting set of highly time resolved data for modeling purposes.

The application of carbon-14 analyses to the source apportionment of atmospheric carbonaceous particulate matter: a review.

PubMed

Heal, Mathew R

2014-01-01

Organic carbon (OC) and elemental carbon (EC) together constitute a substantial proportion of airborne particulate matter (PM). Insight into the sources of this major contributor to PM is important for policies to mitigate the impact of PM on human health and climate change. In recent years measurement of the abundance of the radioisotope of carbon ((14)C) in samples of PM by accelerator mass spectrometry has been used to help quantify the relative contributions from sources of fossil carbon and contemporary carbon. This review provides an introduction to the different sources of carbon within PM and the role of (14)C measurements, a description of the preparation of PM samples and of the instrumentation used to quantify (14)C, and a summary of the results and source apportionment methods reported in published studies since 2004. All studies report a sizable fraction of the carbonaceous PM as of non-fossil origin. Even for PM collected in urban locations, the proportions of non-fossil carbon generally exceed 30%; typically the proportion in urban background locations is around 40-60% depending on the local influence of biomass burning. Where values have been measured directly, proportions of non-fossil carbon in EC are lower than in OC, reflecting the greater contribution of fossil-fuel combustion to EC and the generally small sources of contemporary EC. Detailed source apportionment studies point to important contributions from biogenic-derived secondary OC, consistent with other evidence of a ubiquitous presence of heavily oxidized background secondary OC. The review concludes with some comments on current issues and future prospects, including progress towards compound-class and individual-compound-specific (14)C analyses.

Source apportionment of PM2.5 at the Lin'an regional background site in China with three receptor models

NASA Astrophysics Data System (ADS)

Deng, Junjun; Zhang, Yanru; Qiu, Yuqing; Zhang, Hongliang; Du, Wenjiao; Xu, Lingling; Hong, Youwei; Chen, Yanting; Chen, Jinsheng

2018-04-01

Source apportionment of fine particulate matter (PM2.5) were conducted at the Lin'an Regional Atmospheric Background Station (LA) in the Yangtze River Delta (YRD) region in China from July 2014 to April 2015 with three receptor models including principal component analysis combining multiple linear regression (PCA-MLR), UNMIX and Positive Matrix Factorization (PMF). The model performance, source identification and source contribution of the three models were analyzed and inter-compared. Source apportionment of PM2.5 was also conducted with the receptor models. Good correlations between the reconstructed and measured concentrations of PM2.5 and its major chemical species were obtained for all models. PMF resolved almost all masses of PM2.5, while PCA-MLR and UNMIX explained about 80%. Five, four and seven sources were identified by PCA-MLR, UNMIX and PMF, respectively. Combustion, secondary source, marine source, dust and industrial activities were identified by all the three receptor models. Combustion source and secondary source were the major sources, and totally contributed over 60% to PM2.5. The PMF model had a better performance on separating the different combustion sources. These findings improve the understanding of PM2.5 sources in background region.

Toward Synchronous Evaluation of Source Apportionments for Atmospheric Concentration and Deposition of Sulfate Aerosol Over East Asia

NASA Astrophysics Data System (ADS)

Itahashi, S.

2018-03-01

Source apportionments for atmospheric concentration, dry deposition, and wet deposition of sulfate aerosol (SO42-) were synchronously evaluated over East Asia, a main source of anthropogenic sulfur dioxide (SO2) emissions. Estimating dry deposition was difficult owing to the difficulty of measuring deposition velocity directly; therefore, sensitivity simulations using two dry deposition schemes were conducted. Moreover, sensitivity simulations for different emission inventories, the largest uncertainty source in the air quality model, were also conducted. In total, four experimental settings were used. Model performance was verified for atmospheric concentration and wet deposition using a ground-based observation network in China, Korea, and Japan, and all four model settings captured the observations. The underestimation of wet deposition over China was improved by an adjusted approach that linearly scaled the modeled precipitation values to observations. The synchronous evaluation of source apportionments for atmospheric concentration and dry and wet deposition showed the dominant contribution of anthropogenic emissions from China to the atmospheric concentration and deposition in Japan. The contributions of emissions from volcanoes were more important for wet deposition than for atmospheric concentration. Differences in the dry deposition scheme and emission inventory did not substantially influence the relative ratio of source apportionments over Japan. Because the dry deposition was more attributed to local factors, the differences in dry deposition may be an important determinant of the source contributions from China to Japan. Verification of these findings, including the dry deposition velocity, is necessary for better understanding of the behavior of sulfur compound in East Asia.

Sensitivity tests to define the source apportionment performance criteria in the DeltaSA tool

NASA Astrophysics Data System (ADS)

Pernigotti, Denise; Belis, Claudio A.

2017-04-01

Identification and quantification of the contribution of emission sources to a given area is a key task for the design of abatement strategies. Moreover, European member states are obliged to report this kind of information for zones where the pollution levels exceed the limit values. At present, little is known about the performance and uncertainty of the variety of methodologies used for source apportionment and the comparability between the results of studies using different approaches. The source apportionment Delta (SA Delta) is a tool developed by the EC-JRC to support the particulate matter source apportionment modellers in the identification of sources (for factor analysis studies) and/or in the measure of their performance. The source identification is performed by the tool measuring the proximity of any user chemical profile to preloaded repository data (SPECIATE and SPECIEUROPE). The model performances criteria are based on standard statistical indexes calculated by comparing participants' source contribute estimates and their time series with preloaded references data. Those preloaded data refer to previous European SA intercomparison exercises: the first with real world data (22 participants), the second with synthetic data (25 participants) and the last with real world data which was also extended to Chemical Transport Models (38 receptor models and 4 CTMs). The references used for the model performances are 'true' (predefined by JRC) for the synthetic while they are calculated as ensemble average of the participants' results in real world intercomparisons. The candidates used for each source ensemble reference calculation were selected among participants results based on a number of consistency checks plus the similarity between their chemical profiles to the repository measured data. The estimation of the ensemble reference uncertainty is crucial in order to evaluate the users' performances against it. For this reason a sensitivity analysis on different methods to estimate the ensemble references' uncertainties was performed re-analyzing the synthetic intercomparison dataset, the only one where 'true' reference and ensemble reference contributions were both present. The Delta SA is now available on-line and will be presented, with a critical discussion of the sensitivity analysis on the ensemble reference uncertainty. In particular the grade of among participants mutual agreement on the presence of a certain source should be taken into account. Moreover also the importance of the synthetic intercomparisons in order to catch receptor models common biases will be stressed.

Inter-comparison of receptor models for PM source apportionment: Case study in an industrial area

NASA Astrophysics Data System (ADS)

Viana, M.; Pandolfi, M.; Minguillón, M. C.; Querol, X.; Alastuey, A.; Monfort, E.; Celades, I.

2008-05-01

Receptor modelling techniques are used to identify and quantify the contributions from emission sources to the levels and major and trace components of ambient particulate matter (PM). A wide variety of receptor models are currently available, and consequently the comparability between models should be evaluated if source apportionment data are to be used as input in health effects studies or mitigation plans. Three of the most widespread receptor models (principal component analysis, PCA; positive matrix factorization, PMF; chemical mass balance, CMB) were applied to a single PM10 data set (n=328 samples, 2002-2005) obtained from an industrial area in NE Spain, dedicated to ceramic production. Sensitivity and temporal trend analyses (using the Mann-Kendall test) were applied. Results evidenced the good overall performance of the three models (r2>0.83 and α>0.91×between modelled and measured PM10 mass), with a good agreement regarding source identification and high correlations between input (CMB) and output (PCA, PMF) source profiles. Larger differences were obtained regarding the quantification of source contributions (up to a factor of 4 in some cases). The combined application of different types of receptor models would solve the limitations of each of the models, by constructing a more robust solution based on their strengths. The authors suggest the combined use of factor analysis techniques (PCA, PMF) to identify and interpret emission sources, and to obtain a first quantification of their contributions to the PM mass, and the subsequent application of CMB. Further research is needed to ensure that source apportionment methods are robust enough for application to PM health effects assessments.

Source apportionment of atmospheric particulate matter (PM) using a constrained US-EPA-PMF5.0 model at different urban environments in France

NASA Astrophysics Data System (ADS)

Salameh, Dalia; Favez, Olivier; Golly, Benjamin; Besombes, Jean Luc; Alleman, Laurent; Albinet, Alexandre; Jaffrezo, Jean Luc

2017-04-01

Particulate matter (PM) is one of the most studied atmospheric pollutant in urban areas due to their adverse effects on human health (Pope et al., 2009). Intrinsic properties of PM (e.g. chemical composition and morphology) are directly linked to their origins. Therefore, a harmonized and comprehensive apportionment study of PM sources in urban environments is extremely required to connect source contributions with PM concentration levels and then develop effective PM abatement strategies. Multivariate receptor models such as Positive Matrix Factorization (PMF) are very useful and have been used worldwide for PM source apportionment (Viana et al., 2008). PMF uses a weighted least-squares fit and quantitatively determines source fingerprints (factors) and their contributions to the total PM mass. However, in many cases, it could be tricky to separate two factors that co-vary due to similar seasonal variations, making unclear the physical sense of the extracted factors. To address such issues of source collinearities, additional specific constraints are incorporated into the model (i.e., constrained PMF) based on user's external knowledge allowing better apportionment results. In this work and within the framework of the SOURCES project, a harmonized source apportionment approach has been implemented and applied for the determination of PM sources on a large number of sites (up to 20) of different typologies (e.g. urban background, industrial, traffic, rural and/or alpine sites) distributed all over France and previously investigated with annual or multiannual studies (2012-2016). A constrained PMF approach (using US-EPA PMF5.0 software) was applied to the comprehensive PM-offline chemical datasets (i.e. carbonaceous fraction, major ions, metals/trace elements, specific organic markers) in a harmonized way for all the investigated sites. Different types of specific chemical constraints from well-characterized sources were defined based on external knowledge and were imposed to some species in the PMF factor profiles. As an example, the contributions of the levoglucosan, a specific tracer of the biomass burning emissions, were pulled up maximally in the biomass burning factor profiles and were set to zero in all other resolved factors (e.g. vehicular emissions, biogenic emissions, etc,…). The different source categories contributing to ambient PM concentration levels were chemically characterized and quantified. Chemical profiles of the resolved common sources have been exploited and compared allowing us to get extra knowledge on the spatial variabilities of the source compositions. The presentation will address the main points achieved with this program. Pope, I. C., et al. (2009), New England Journal of Medicine, 360(4), 376-386. Viana, M., et al. (2008), Journal of Aerosol Science, 39(10), 827-849. Acknowledgments: This work, including a postdoctoral grant for D Salameh, is funded by the French Ministry of Environment, Energy, and Sea (MEEM) through the Environment and Energy Management Agency (ADEME, contract 1462C0044) and the national reference laboratory for air quality monitoring (LCSQA). The authors also gratefully acknowledge the funding by ANDRA of the program conducted at OPE by S Conil, and all dedicated staffs within the French regional monitoring networks for collecting the samples.

Approaches to Children’s Exposure Assessment: Case Study with Diethylhexylphthalate (DEHP)

PubMed Central

Ginsberg, Gary; Ginsberg, Justine; Foos, Brenda

2016-01-01

Children’s exposure assessment is a key input into epidemiology studies, risk assessment and source apportionment. The goals of this article are to describe a methodology for children’s exposure assessment that can be used for these purposes and to apply the methodology to source apportionment for the case study chemical, diethylhexylphthalate (DEHP). A key feature is the comparison of total (aggregate) exposure calculated via a pathways approach to that derived from a biomonitoring approach. The 4-step methodology and its results for DEHP are: (1) Prioritization of life stages and exposure pathways, with pregnancy, breast-fed infants, and toddlers the focus of the case study and pathways selected that are relevant to these groups; (2) Estimation of pathway-specific exposures by life stage wherein diet was found to be the largest contributor for pregnant women, breast milk and mouthing behavior for the nursing infant and diet, house dust, and mouthing for toddlers; (3) Comparison of aggregate exposure by pathways vs biomonitoring-based approaches wherein good concordance was found for toddlers and pregnant women providing confidence in the exposure assessment; (4) Source apportionment in which DEHP presence in foods, children’s products, consumer products and the built environment are discussed with respect to early life mouthing, house dust and dietary exposure. A potential fifth step of the method involves the calculation of exposure doses for risk assessment which is described but outside the scope for the current case study. In summary, the methodology has been used to synthesize the available information to identify key sources of early life exposure to DEHP. PMID:27376320

A Bayesian Multivariate Receptor Model for Estimating Source Contributions to Particulate Matter Pollution using National Databases.

PubMed

Hackstadt, Amber J; Peng, Roger D

2014-11-01

Time series studies have suggested that air pollution can negatively impact health. These studies have typically focused on the total mass of fine particulate matter air pollution or the individual chemical constituents that contribute to it, and not source-specific contributions to air pollution. Source-specific contribution estimates are useful from a regulatory standpoint by allowing regulators to focus limited resources on reducing emissions from sources that are major contributors to air pollution and are also desired when estimating source-specific health effects. However, researchers often lack direct observations of the emissions at the source level. We propose a Bayesian multivariate receptor model to infer information about source contributions from ambient air pollution measurements. The proposed model incorporates information from national databases containing data on both the composition of source emissions and the amount of emissions from known sources of air pollution. The proposed model is used to perform source apportionment analyses for two distinct locations in the United States (Boston, Massachusetts and Phoenix, Arizona). Our results mirror previous source apportionment analyses that did not utilize the information from national databases and provide additional information about uncertainty that is relevant to the estimation of health effects.

Source apportionment for fine particulate matter in a Chinese city using an improved gas-constrained method and comparison with multiple receptor models.

PubMed

Shi, Guoliang; Liu, Jiayuan; Wang, Haiting; Tian, Yingze; Wen, Jie; Shi, Xurong; Feng, Yinchang; Ivey, Cesunica E; Russell, Armistead G

2018-02-01

PM 2.5 is one of the most studied atmospheric pollutants due to its adverse impacts on human health and welfare and the environment. An improved model (the chemical mass balance gas constraint-Iteration: CMBGC-Iteration) is proposed and applied to identify source categories and estimate source contributions of PM 2.5. The CMBGC-Iteration model uses the ratio of gases to PM as constraints and considers the uncertainties of source profiles and receptor datasets, which is crucial information for source apportionment. To apply this model, samples of PM 2.5 were collected at Tianjin, a megacity in northern China. The ambient PM 2.5 dataset, source information, and gas-to-particle ratios (such as SO 2 /PM 2.5 , CO/PM 2.5 , and NOx/PM 2.5 ratios) were introduced into the CMBGC-Iteration to identify the potential sources and their contributions. Six source categories were identified by this model and the order based on their contributions to PM 2.5 was as follows: secondary sources (30%), crustal dust (25%), vehicle exhaust (16%), coal combustion (13%), SOC (7.6%), and cement dust (0.40%). In addition, the same dataset was also calculated by other receptor models (CMB, CMB-Iteration, CMB-GC, PMF, WALSPMF, and NCAPCA), and the results obtained were compared. Ensemble-average source impacts were calculated based on the seven source apportionment results: contributions of secondary sources (28%), crustal dust (20%), coal combustion (18%), vehicle exhaust (17%), SOC (11%), and cement dust (1.3%). The similar results of CMBGC-Iteration and ensemble method indicated that CMBGC-Iteration can produce relatively appropriate results. Copyright © 2017 Elsevier Ltd. All rights reserved.

Bioavailability of Polycyclic Aromatic Hydrocarbons and their Potential Application in Eco-risk Assessment and Source Apportionment in Urban River Sediment

PubMed Central

Yang, Xunan; Yu, Liuqian; Chen, Zefang; Xu, Meiying

2016-01-01

Traditional risk assessment and source apportionment of sediments based on bulk polycyclic aromatic hydrocarbons (PAHs) can introduce biases due to unknown aging effects in various sediments. We used a mild solvent (hydroxypropyl-β-cyclodextrin) to extract the bioavailable fraction of PAHs (a-PAHs) from sediment samples collected in Pearl River, southern China. We investigated the potential application of this technique for ecological risk assessments and source apportionment. We found that the distribution of PAHs was associated with human activities and that the a-PAHs accounted for a wide range (4.7%–21.2%) of total-PAHs (t-PAHs), and high risk sites were associated with lower t-PAHs but higher a-PAHs. The correlation between a-PAHs and the sediment toxicity assessed using tubificid worms (r = −0.654, P = 0.021) was greater than that from t-PAH-based risk assessment (r = −0.230, P = 0.472). Moreover, the insignificant correlation between a-PAH content and mPEC-Q of low molecular weight PAHs implied the potiential bias of t-PAH-based risk assessment. The source apportionment from mild extracted fractions was consistent across different indicators and was in accordance with typical pollution sources. Our results suggested that mild extraction-based approaches reduce the potential error from aging effects because the mild extracted PAHs provide a more direct indicator of bioavailability and fresher fractions in sediments. PMID:26976450

DEVELOPMENT OF URINARY METABOLITE BIOMARKERS TO ASSESS POPULATION EXPOSURE TO PM2.5 FROM VARIOUS COMBUSTION SOURCES

EPA Science Inventory

A primary goal of our research is to validate the use of urinary biomarkers to apportion the sources of human exposure to PM2.5. Organic source tracers have been used in source apportionment studies of ambient PM2.5 to distinguish a range of combustion sources. Both gas and par...

Receptor modeling for source apportionment of polycyclic aromatic hydrocarbons in urban atmosphere.

PubMed

Singh, Kunwar P; Malik, Amrita; Kumar, Ranjan; Saxena, Puneet; Sinha, Sarita

2008-01-01

This study reports source apportionment of polycyclic aromatic hydrocarbons (PAHs) in particulate depositions on vegetation foliages near highway in the urban environment of Lucknow city (India) using the principal components analysis/absolute principal components scores (PCA/APCS) receptor modeling approach. The multivariate method enables identification of major PAHs sources along with their quantitative contributions with respect to individual PAH. The PCA identified three major sources of PAHs viz. combustion, vehicular emissions, and diesel based activities. The PCA/APCS receptor modeling approach revealed that the combustion sources (natural gas, wood, coal/coke, biomass) contributed 19-97% of various PAHs, vehicular emissions 0-70%, diesel based sources 0-81% and other miscellaneous sources 0-20% of different PAHs. The contributions of major pyrolytic and petrogenic sources to the total PAHs were 56 and 42%, respectively. Further, the combustion related sources contribute major fraction of the carcinogenic PAHs in the study area. High correlation coefficient (R2 > 0.75 for most PAHs) between the measured and predicted concentrations of PAHs suggests for the applicability of the PCA/APCS receptor modeling approach for estimation of source contribution to the PAHs in particulates.

Identifying the Sources Contributing to PM Exceedances in Ostrava, Czech Republic, Using Passive Aerosol Sampling Coupled with Computer-Controlled Microscopy

EPA Science Inventory

The Czech Hydrometeorological Institute (CHMI) in collaboration with the U.S. Environmental Protection Agency conducted a multi-pollutant source apportionment study in 2012 to quantify the impact of regional as well as local sources on air quality in the Ostrava metropolitan area...

DeltaSA tool for source apportionment benchmarking, description and sensitivity analysis

NASA Astrophysics Data System (ADS)

Pernigotti, D.; Belis, C. A.

2018-05-01

DeltaSA is an R-package and a Java on-line tool developed at the EC-Joint Research Centre to assist and benchmark source apportionment applications. Its key functionalities support two critical tasks in this kind of studies: the assignment of a factor to a source in factor analytical models (source identification) and the model performance evaluation. The source identification is based on the similarity between a given factor and source chemical profiles from public databases. The model performance evaluation is based on statistical indicators used to compare model output with reference values generated in intercomparison exercises. The references values are calculated as the ensemble average of the results reported by participants that have passed a set of testing criteria based on chemical profiles and time series similarity. In this study, a sensitivity analysis of the model performance criteria is accomplished using the results of a synthetic dataset where "a priori" references are available. The consensus modulated standard deviation punc gives the best choice for the model performance evaluation when a conservative approach is adopted.

Atmospheric polycyclic aromatic hydrocarbons in the urban environment: Occurrence, toxicity and source apportionment.

PubMed

Mishra, Nitika; Ayoko, Godwin A; Morawska, Lidia

2016-01-01

Polycyclic Aromatic Hydrocarbons (PAHs) represent a major class of toxic pollutants because of their carcinogenic and mutagenic characteristics. People living in urban areas are regularly exposed to PAHs because of abundance of their emission sources. Within this context, this study aimed to: (i) identify and quantify the levels of ambient PAHs in an urban environment; (ii) evaluate their toxicity; and (iii) identify their sources as well as the contribution of specific sources to measured concentrations. Sixteen PAHs were identified and quantified in air samples collected from Brisbane. Principal Component Analysis - Absolute Principal Component Scores (PCA-APCS) was used in order to conduct source apportionment of the measured PAHs. Vehicular emissions, natural gas combustion, petrol emissions and evaporative/unburned fuel were the sources identified; contributing 56%, 21%, 15% and 8% of the total PAHs emissions, respectively, all of which need to be considered for any pollution control measures implemented in urban areas. Copyright © 2015 Elsevier Ltd. All rights reserved.

Volatility-resolved source apportionment of primary and secondary organic aerosol over Europe

NASA Astrophysics Data System (ADS)

Skyllakou, Ksakousti; Fountoukis, Christos; Charalampidis, Panagiotis; Pandis, Spyros N.

2017-10-01

A three-dimensional regional chemical transport model (Particulate Matter Comprehensive Air Quality Model with Extensions, PMCAMx) was applied over Europe combined with a source apportionment algorithm, the Particulate Source Apportionment Technology (PSAT), in order to quantify the sources which contribute to the primary and secondary organic aerosol (OA) during different seasons. The PSAT algorithm was first extended to allow the quantification of the sources of OA as a function of volatility. The most significant OA sources during May were biogenic, while during February residential wood combustion and during September wildfires dominated. The contributions of the various sources have strong spatial dependence. Wildfires were significant OA sources (38% of the OA) for Russia during September, but had a much lower impact (5%) in Scandinavia. The above results are in general consistent with the findings of the CARBOSOL project for selected sites in Europe. For remote sites such as Finokalia in Crete, more than 90% of the OA has undergone two or more generations of oxidation for all seasons. This highly processed oxidized OA is predicted to also dominate over much of Europe during the summer and fall. The first generation SOA is predicted to represent 20-30% of the OA in central and northern Europe during these photochemically active periods.

EPA’s Study of Potential Impacts of Hydraulic Fracturing on Drinking Water Resources: Wastewater Source Apportionment Project

EPA Pesticide Factsheets

EPA scientists evaluated sources of bromide and other inorganic pollutants impacting drinking water intakes on the Allegheny River in Pennsylvania to examine the potential impacts related to the treatment and disposal of oil & gas well produced wastewater.

Source apportionment of heavy metals in agricultural soil based on PMF: A case study in Hexi Corridor, northwest China.

PubMed

Guan, Qingyu; Wang, Feifei; Xu, Chuanqi; Pan, Ninghui; Lin, Jinkuo; Zhao, Rui; Yang, Yanyan; Luo, Haiping

2018-02-01

Hexi Corridor is the most important base of commodity grain and producing area for cash crops. However, the rapid development of agriculture and industry has inevitably led to heavy metal contamination in the soils. Multivariate statistical analysis, GIS-based geostatistical methods and Positive Matrix Factorization (PMF) receptor modeling techniques were used to understand the levels of heavy metals and their source apportionment for agricultural soil in Hexi Corridor. The results showed that the average concentrations of Cr, Cu, Ni, Pb and Zn were lower than the secondary standard of soil environmental quality; however, the concentrations of eight metals (Cr, Cu, Mn, Ni, Pb, Ti, V and Zn) were higher than background values, and their corresponding enrichment factor values were significantly greater than 1. Different degrees of heavy metal pollution occurred in the agricultural soils; specifically, Ni had the most potential for impacting human health. The results from the multivariate statistical analysis and GIS-based geostatistical methods indicated both natural sources (Co and W) and anthropogenic sources (Cr, Cu, Mn, Ni, Pb, Ti, V and Zn). To better identify pollution sources of heavy metals in the agricultural soils, the PMF model was applied. Further source apportionment revealed that enrichments of Pb and Zn were attributed to traffic sources; Cr and Ni were closely related to industrial activities, including mining, smelting, coal combustion, iron and steel production and metal processing; Zn and Cu originated from agricultural activities; and V, Ti and Mn were derived from oil- and coal-related activities. Copyright © 2017 Elsevier Ltd. All rights reserved.

Air quality assessment and the use of specific markers to apportion pollutants to source

NASA Astrophysics Data System (ADS)

Douce, David Stewart

The contributions of specific polluting sources to both indoor and outdoor atmospheric pollution are difficult to determine, as solid and gaseous products from different combustion sources are often similar. Sometimes, however, a marker compound can be identified that is unique to a pollution source (or at least not present in most other local combustion sources) and which will allow assessment of the contribution of that source to total atmospheric pollution.The aim of this study was to identify suitable marker compounds and methods for the apportionment (assessment of percentage contribution) of specific sources to atmospheric pollution. The sources selected were diesel exhaust emissions in outdoor, and environmental tobacco smoke (ETS) in indoor environments. Studies with controlled (laboratory) atmospheres would be followed by field studies using these methods and markers to produce apportionments for these sources to air pollution in selected environments. Initial analysis of such polluting sources was therefore the qualitative analysis of volatile compounds and particulate associated material, both organic and inorganic. Volatile organic compounds were adsorbed onto various resins, while particulate material was sampled onto various filter paper types. Organics were determined by GC-AED and GC-MS, and elements by ICP-MS.1-Nitropyrene was identified as a suitable marker for diesel particulate emissions (<5um). A large volume air sample from Sheffield city centre using 1-nitropyrene as a marker suggested that 63% of atmospheric particulate material (<5um) might be of diesel origin. However the concentration of 1-nitropyrene is low in atmospheric samples, and in the volumes used in routine sampling the amount of 1-nitropyrene was below the limit of detection on the instrument used. In an alternative approach the aliphatic alkane tetracosane (C24) was used as a diesel marker for urban air, with a 1-nitropyrene:tetracosane ratio derived from the average results from laboratory experiments with a diesel engine running at various speeds and loads. This approach yielded apportionment values ranging from 5-85% for the diesel contribution to particulate material (<5mum) in the urban air of Sheffield. No volatile marker compound was found for diesel apportionment.The contribution of ETS to atmospheric pollution has previously been estimated from the measurement of respirable suspended particulates (RSP), which was superseded by total UV absorbance and total fluorescence of a methanol extract. More recent work has suggested the use of solanesol or scopoletin as marker compounds. This thesis shows that the non specific methods overestimated the particulate contribution of ETS in some atmospheres, and that solanesol is a better marker compound than scopoletin. Preliminary studies from a small number of smokers homes and offices, with solanesol as a marker compound for particulate ETS, indicated that ETS contributions to total particulate material (<5mum) ranged from 6 to 49% in homes and 11 to 28% in offices.Pyrrole was used as a marker for ETS contribution to volatile organic pollution, and studies with controlled atmospheres with a smoking machine allowed calculation of the ratios of pyrrole to other volatile organic compounds (VOC's) in ETS. Samples from the field study were used to produce apportionment percentage levels of benzene, toluene, o-xylene and p+m-xylene associated with ETS.In addition the use of tree bark as a atmospheric sink for airborne particulates was investigated. Six nitrated polycyclic aromatic hydrocarbons associated with diesel emissions were quantified in bark extracts and levels of these were found to be highest during winter months.

[Source apportionment of soil heavy metals in Jiapigou goldmine based on the UNMIX model].

PubMed

Ai, Jian-chao; Wang, Ning; Yang, Jing

2014-09-01

The paper determines 16 kinds of metal elements' concentration in soil samples which collected in Jipigou goldmine upper the Songhua River. The UNMIX Model which was recommended by US EPA to get the source apportionment results was applied in this study, Cd, Hg, Pb and Ag concentration contour maps were generated by using Kriging interpolation method to verify the results. The main conclusions of this study are: (1)the concentrations of Cd, Hg, Pb and Ag exceeded Jilin Province soil background values and enriched obviously in soil samples; (2)using the UNMIX Model resolved four pollution sources: source 1 represents human activities of transportation, ore mining and garbage, and the source 1's contribution is 39. 1% ; Source 2 represents the contribution of the weathering of rocks and biological effects, and the source 2's contribution is 13. 87% ; Source 3 is a comprehensive source of soil parent material and chemical fertilizer, and the source 3's contribution is 23. 93% ; Source 4 represents iron ore mining and transportation sources, and the source 4's contribution is 22. 89%. (3)the UNMIX Model results are in accordance with the survey of local land-use types, human activities and Cd, Hg and Pb content distributions.

Contamination characteristics and source apportionment of trace metals in soils around Miyun Reservoir.

PubMed

Chen, Haiyang; Teng, Yanguo; Chen, Ruihui; Li, Jiao; Wang, Jinsheng

2016-08-01

Due to their toxicity and bioaccumulation, trace metals in soils can result in a wide range of toxic effects on animals, plants, microbes, and even humans. Recognizing the contamination characteristics of soil metals and especially apportioning their potential sources are the necessary preconditions for pollution prevention and control. Over the past decades, several receptor models have been developed for source apportionment. Among them, positive matrix factorization (PMF) has gained popularity and was recommended by the US Environmental Protection Agency as a general modeling tool. In this study, an extended chemometrics model, multivariate curve resolution-alternating least squares based on maximum likelihood principal component analysis (MCR-ALS/MLPCA), was proposed for source apportionment of soil metals and applied to identify the potential sources of trace metals in soils around Miyun Reservoir. Similar to PMF, the MCR-ALS/MLPCA model can incorporate measurement error information and non-negativity constraints in its calculation procedures. Model validation with synthetic dataset suggested that the MCR-ALS/MLPCA could extract acceptable recovered source profiles even considering relatively larger error levels. When applying to identify the sources of trace metals in soils around Miyun Reservoir, the MCR-ALS/MLPCA model obtained the highly similar profiles with PMF. On the other hand, the assessment results of contamination status showed that the soils around reservoir were polluted by trace metals in slightly moderate degree but potentially posed acceptable risks to the public. Mining activities, fertilizers and agrochemicals, and atmospheric deposition were identified as the potential anthropogenic sources with contributions of 24.8, 14.6, and 13.3 %, respectively. In order to protect the drinking water source of Beijing, special attention should be paid to the metal inputs to soils from mining and agricultural activities.

Source apportionment and pollution evaluation of heavy metals in water and sediments of Buriganga River, Bangladesh, using multivariate analysis and pollution evaluation indices.

PubMed

Bhuiyan, Mohammad Amir Hossain; Dampare, Samuel B; Islam, M A; Suzuki, Shigeyuki

2015-01-01

Concentrations of heavy metals in water and sediment samples of Buriganga River in the capital city Dhaka, Bangladesh, were studied to understand the level of heavy metals and their source apportionment. The results showed that the mean concentrations of heavy metals both in water and sediment samples were very high and, in most cases, exceeded the permissible limits recommended by the Bangladesh government and other international organizations. Significantly higher concentrations of Pb, Cr, Mn, Co, Ni, Cu, Zn, As, and Cd were found in sediment samples. However, average concentrations of metals both in water and sediment samples were above the effect range median. The heavy metal pollution index (HPI) and degree of contamination (Cd) yielded different results in water samples despite significant correlations between them. The heavy metal evaluation index (HEI) showed strong correlations with HPI and Cd and provided better assessment of pollution levels. The enrichment factor (EF) and geoaccumulation index (Igeo) showed the elevated value of Cr, Pb, and Cd in access of background values. The measured elements were subjected to positive matrix factorization (PMF) and examining correlations in order to explain the content, behavior, and source apportionment of metals. PMF resulted in a successful partitioning of variances into sources related to background geochemistry and contaminant influences. However, the PMF approach successfully demarcated the major sources of metals from tannery, paint, municipal sewage, textiles, and agricultural activities.

Source apportionment of airborne particulates through receptor modeling: Indian scenario

NASA Astrophysics Data System (ADS)

Banerjee, Tirthankar; Murari, Vishnu; Kumar, Manish; Raju, M. P.

2015-10-01

Airborne particulate chemistry mostly governed by associated sources and apportionment of specific sources is extremely essential to delineate explicit control strategies. The present submission initially deals with the publications (1980s-2010s) of Indian origin which report regional heterogeneities of particulate concentrations with reference to associated species. Such meta-analyses clearly indicate the presence of reservoir of both primary and secondary aerosols in different geographical regions. Further, identification of specific signatory molecules for individual source category was also evaluated in terms of their scientific merit and repeatability. Source signatures mostly resemble international profile while, in selected cases lack appropriateness. In India, source apportionment (SA) of airborne particulates was initiated way back in 1985 through factor analysis, however, principal component analysis (PCA) shares a major proportion of applications (34%) followed by enrichment factor (EF, 27%), chemical mass balance (CMB, 15%) and positive matrix factorization (PMF, 9%). Mainstream SA analyses identify earth crust and road dust resuspensions (traced by Al, Ca, Fe, Na and Mg) as a principal source (6-73%) followed by vehicular emissions (traced by Fe, Cu, Pb, Cr, Ni, Mn, Ba and Zn; 5-65%), industrial emissions (traced by Co, Cr, Zn, V, Ni, Mn, Cd; 0-60%), fuel combustion (traced by K, NH4+, SO4-, As, Te, S, Mn; 4-42%), marine aerosols (traced by Na, Mg, K; 0-15%) and biomass/refuse burning (traced by Cd, V, K, Cr, As, TC, Na, K, NH4+, NO3-, OC; 1-42%). In most of the cases, temporal variations of individual source contribution for a specific geographic region exhibit radical heterogeneity possibly due to unscientific orientation of individual tracers for specific source and well exaggerated by methodological weakness, inappropriate sample size, implications of secondary aerosols and inadequate emission inventories. Conclusively, a number of challenging issues and specific recommendations have been included which need to be considered for a scientific apportionment of particulate sources in different geographical regions of India.

Chemical mass balance source apportionment of fine and PM10 in the Desert Southwest, USA

EPA Science Inventory

The Desert Southwest Coarse Particulate Matter Study was undertaken in Pinal County, Arizona, to better understand the origin and impact of sources of fine and coarse particulate matter (PM) in rural, arid regions of the U.S. southwestern desert. The desert southwest experiences ...

Source Apportionment of the Summer Time Carbonaceous Aerosol at Nordic Rural Background Sites

EPA Science Inventory

In the present study, natural and anthropogenic sources of particulate organic carbon (OC_p) and elemental carbon (EC) have been quantified based on weekly filter samples of PM₁₀ (particles with aerodynamic diameter <10µ collected at four Nordic rural backgro...

SOURCE APPORTIONMENT OF FINE PARTICULATE MATTER IN THE U.S. AND ASSOCIATIONS WITH LUNG INFLAMMATORY MARKERS IL -8, COX -2 AND HO -1

EPA Science Inventory

Associations are well established between particulate matter (PM) and increased human mortality and morbidity. The association between fine PM sources and lung inflammatory markers IL-8, COX-2, and HO-1 was evaluated in this study.

Size-Differentiated Chemical Composition of Re-Suspended Soil Dust from the Desert Southwest United States

EPA Science Inventory

As part of the Desert Southwest Coarse Particulate Matter Study which characterized the composition of fine and coarse particulate matter in Pinal County, AZ, several source samples were collected from several different soil types to assist in source apportionment analysis of the...

Impacts of Oil and Gas Production on Winter Ozone Pollution in the Uintah Basin Using Model Source Apportionment

NASA Astrophysics Data System (ADS)

Tran, H. N. Q.; Tran, T. T.; Mansfield, M. L.; Lyman, S. N.

2014-12-01

Contributions of emissions from oil and gas activities to elevated ozone concentrations in the Uintah Basin - Utah were evaluated using the CMAQ Integrated Source Apportionment Method (CMAQ-ISAM) technique, and were compared with the results of traditional budgeting methods. Unlike the traditional budgeting method, which compares simulations with and without emissions of the source(s) in question to quantify its impacts, the CMAQ-ISAM technique assigns tags to emissions of each source and tracks their evolution through physical and chemical processes to quantify the final ozone product yield from the source. Model simulations were performed for two episodes in winter 2013 of low and high ozone to provide better understanding of source contributions under different weather conditions. Due to the highly nonlinear ozone chemistry, results obtained from the two methods differed significantly. The growing oil and gas industry in the Uintah Basin is the largest contributor to the elevated zone (>75 ppb) observed in the Basin. This study therefore provides an insight into the impact of oil and gas industry on the ozone issue, and helps in determining effective control strategies.

Fine Particulate Pollution and Source Apportionment in the Urban Centers for Africa, Asia and Latin America

NASA Astrophysics Data System (ADS)

Guttikunda, S. K.; Johnson, T. M.; Procee, P.

2004-12-01

Fossil fuel combustion for domestic cooking and heating, power generation, industrial processes, and motor vehicles are the primary sources of air pollution in the developing country cities. Over the past twenty years, major advances have been made in understanding the social and economic consequences of air pollution. In both industrialized and developing countries, it has been shown that air pollution from energy combustion has detrimental impacts on human health and the environment. Lack of information on the sectoral contributions to air pollution - especially fine particulates, is one of the typical constraints for an effective integrated urban air quality management program. Without such information, it is difficult, if not impossible, for decision makers to provide policy advice and make informed investment decisions related to air quality improvements in developing countries. This also raises the need for low-cost ways of determining the principal sources of fine PM for a proper planning and decision making. The project objective is to develop and verify a methodology to assess and monitor the sources of PM, using a combination of ground-based monitoring and source apportionment techniques. This presentation will focus on four general tasks: (1) Review of the science and current activities in the combined use of monitoring data and modeling for better understanding of PM pollution. (2) Review of recent advances in atmospheric source apportionment techniques (e.g., principal component analysis, organic markers, source-receptor modeling techniques). (3) Develop a general methodology to use integrated top-down and bottom-up datasets. (4) Review of a series of current case studies from Africa, Asia and Latin America and the methodologies applied to assess the air pollution and its sources.

EVALUATION OF THE CMB AND PMF MODELS USING ORGANIC MOLECULAR MARKERS IN FINE PARTICULATE MATTER COLLECTED DURING THE PITTSBURGH AIR QUALITY STUDY

EPA Science Inventory

This research investigated different strategies for source apportionment of airborne fine particulate matter (PM2.5) collected as part of the Pittsburgh Air Quality Study. Two source receptor models were used, the EPA Chemical Mass Balance 8.2 (CMB) and EPA Positive Matrix Facto...

Indoor source apportionment in urban communities near industrial sites

NASA Astrophysics Data System (ADS)

Tunno, Brett J.; Dalton, Rebecca; Cambal, Leah; Holguin, Fernando; Lioy, Paul; Clougherty, Jane E.

2016-08-01

Because fine particulate matter (PM2.5) differs in chemical composition, source apportionment is frequently used for identification of relative contributions of multiple sources to outdoor concentrations. Indoor air pollution and source apportionment is often overlooked, though people in northern climates may spend up to 90% of their time inside. We selected 21 homes for a 1-week indoor sampling session during summer (July to September 2011), repeated in winter (January to March 2012). Elemental analysis was performed using inductively-coupled plasma mass spectrometry (ICP-MS), and factor analysis was used to determine constituent grouping. Multivariate modeling was run on factor scores to corroborate interpretations of source factors based on a literature review. For each season, a 5-factor solution explained 86-88% of variability in constituent concentrations. Indoor sources (i.e. cooking, smoking) explained greater variability than did outdoor sources in these industrial communities. A smoking factor was identified in each season, predicted by number of cigarettes smoked. Cooking factors were also identified in each season, explained by frequency of stove cooking and stovetop frying. Significant contributions from outdoor sources including coal and motor vehicles were also identified. Higher coal and secondary-related elemental concentrations were detected during summer than winter. Our findings suggest that source contributions to indoor concentrations can be identified and should be examined in relation to health effects.

Occurrence and source apportionment of sulfonamides and their metabolites in Liaodong Bay and the adjacent Liao River basin, North China.

PubMed

Jia, Ai; Hu, Jianying; Wu, Xiaoqin; Peng, Hui; Wu, Shimin; Dong, Zhaomin

2011-06-01

The presence of antibiotics in the environment is of great concern because of their potential for resistance selection among pathogens. In the present study we investigated the occurrence of 19 sulfonamides, five N-acetylated sulfonamide metabolites, and trimethoprim in the Liao River basin and adjacent Liaodong Bay, China, as well as 10 human/agricultural source samples. Within the 35 river samples, 12 sulfonamides, four acetylated sulfonamides, and trimethoprim were detected, with the dominant being sulfamethoxazole (66.6 ng/L), N-acetylsulfamethoxazole (63.1 ng/L), trimethoprim (29.0 ng/L), sulfadiazine (14.0 ng/L), and sulfamonomethoxine (8.4 ng/L); within the 36 marine samples, 10 chemicals were detected, with the main contributions from sulfamethoxazole (25.2 ng/L) and N-acetylsulfamethoxazole (28.6 ng/L). Sulfamethoxazole (25.9%), N-acetylsulfamethoxazole (46.6%), trimethoprim (22.9%), and sulfapyridine (1.4%) were the main chemicals from human sources, while sulfamonomethoxine, sulfamethazine, sulfaquinoxaline, sulfaguanidine, sulfadiazine, sulfanilamide, and sulfamethoxypyridazine were dominant in the animal husbandry sources, specifically, swine and poultry farms, and sulfamethoxazole (91%) was dominant in the mariculture source. A principal component analysis with multiple linear regression was performed to evaluate the source apportionment of total sulfonamides in Liaodong Bay. It was found that animal husbandry contributed 15.2% of total sulfonamides, while human sources contributed 28.5%, and combined human and mariculture sources contributed 56.3%. In addition, the mariculture contribution was 24.1% of total sulfonamides into the sea based on mass flux estimation. The present study is the first report that the environmental levels of sulfonamide metabolites were comparable to the corresponding parents; therefore, we should pay attention to their environmental occurrence. Source apportionment showed human discharge (60.7%) significantly contributed to these antibiotics in Liaodong Bay, which provides important information for environmental management. Copyright © 2011 SETAC.

Sediment source apportionment in Laurel Hill Creek, PA, using Bayesian chemical mass balance and isotope fingerprinting

USGS Publications Warehouse

Stewart, Heather; Massoudieh, Arash; Gellis, Allen C.

2015-01-01

A Bayesian chemical mass balance (CMB) approach was used to assess the contribution of potential sources for fluvial samples from Laurel Hill Creek in southwest Pennsylvania. The Bayesian approach provides joint probability density functions of the sources' contributions considering the uncertainties due to source and fluvial sample heterogeneity and measurement error. Both elemental profiles of sources and fluvial samples and 13C and 15N isotopes were used for source apportionment. The sources considered include stream bank erosion, forest, roads and agriculture (pasture and cropland). Agriculture was found to have the largest contribution, followed by stream bank erosion. Also, road erosion was found to have a significant contribution in three of the samples collected during lower-intensity rain events. The source apportionment was performed with and without isotopes. The results were largely consistent; however, the use of isotopes was found to slightly increase the uncertainty in most of the cases. The correlation analysis between the contributions of sources shows strong correlations between stream bank and agriculture, whereas roads and forest seem to be less correlated to other sources. Thus, the method was better able to estimate road and forest contributions independently. The hypothesis that the contributions of sources are not seasonally changing was tested by assuming that all ten fluvial samples had the same source contributions. This hypothesis was rejected, demonstrating a significant seasonal variation in the sources of sediments in the stream.

Source apportionment of population representative samples of PM(2.5) in three European cities using structural equation modelling.

PubMed

Ilacqua, Vito; Hänninen, Otto; Saarela, Kristina; Katsouyanni, Klea; Künzli, Nino; Jantunen, Matti

2007-10-01

Apportionment of urban particulate matter (PM) to sources is central for air quality management and efficient reduction of the substantial public health risks associated with fine particles (PM(2.5)). Traffic is an important source combustion particles, but also a significant source of resuspended particles that chemically resemble Earth's crust and that are not affected by development of cleaner motor technologies. A substantial fraction of urban ambient PM originates from long-range transport outside the immediate urban environment including secondary particles formed from gaseous emissions of mainly sulphur, nitrogen oxides and ammonia. Most source apportionment studies are based on small number of fixed monitoring sites and capture well population exposures to regional and long-range transported particles. However, concentrations from local sources are very unevenly distributed and the results from such studies are therefore poorly representative of the actual exposures. The current study uses PM(2.5) data observed at population based random sampled residential locations in Athens, Basle and Helsinki with 17 elemental constituents, selected VOCs (xylenes, trimethylbenzenes, nonane and benzene) and light absorbance (black smoke). The major sources identified across the three cities included crustal, salt, long-range transported inorganic and traffic sources. Traffic was associated separately with source categories with crustal (especially Athens and Helsinki) and long-range transported chemical composition (all cities). Remarkably high fractions of the variability of elemental (R(2)>0.6 except for Ca in Basle 0.38) and chemical concentrations (R(2)>0.5 except benzene in Basle 0.22 and nonane in Athens 0.39) are explained by the source factors of an SEM model. The RAINS model that is currently used as the main tool in developing European air quality management policies seems to capture the local urban fraction (the city delta term) quite well, but underestimates crustal particle levels in the three cities of the current study. Utilizing structural equation modelling parallel with traditional principal component analysis (PCA) provides an objective method to determine the number of factors to be retained in a model and allows for formal hypotheses testing.

Ensemble-Based Source Apportionment of Fine Particulate Matter and Emergency Department Visits for Pediatric Asthma

PubMed Central

Gass, Katherine; Balachandran, Sivaraman; Chang, Howard H.; Russell, Armistead G.; Strickland, Matthew J.

2015-01-01

Epidemiologic studies utilizing source apportionment (SA) of fine particulate matter have shown that particles from certain sources might be more detrimental to health than others; however, it is difficult to quantify the uncertainty associated with a given SA approach. In the present study, we examined associations between source contributions of fine particulate matter and emergency department visits for pediatric asthma in Atlanta, Georgia (2002–2010) using a novel ensemble-based SA technique. Six daily source contributions from 4 SA approaches were combined into an ensemble source contribution. To better account for exposure uncertainty, 10 source profiles were sampled from their posterior distributions, resulting in 10 time series with daily SA concentrations. For each of these time series, Poisson generalized linear models with varying lag structures were used to estimate the health associations for the 6 sources. The rate ratios for the source-specific health associations from the 10 imputed source contribution time series were combined, resulting in health associations with inflated confidence intervals to better account for exposure uncertainty. Adverse associations with pediatric asthma were observed for 8-day exposure to particles generated from diesel-fueled vehicles (rate ratio = 1.06, 95% confidence interval: 1.01, 1.10) and gasoline-fueled vehicles (rate ratio = 1.10, 95% confidence interval: 1.04, 1.17). PMID:25776011

Space-time quantitative source apportionment of soil heavy metal concentration increments.

PubMed

Yang, Yong; Christakos, George; Guo, Mingwu; Xiao, Lu; Huang, Wei

2017-04-01

Assessing the space-time trends and detecting the sources of heavy metal accumulation in soils have important consequences in the prevention and treatment of soil heavy metal pollution. In this study, we collected soil samples in the eastern part of the Qingshan district, Wuhan city, Hubei Province, China, during the period 2010-2014. The Cd, Cu, Pb and Zn concentrations in soils exhibited a significant accumulation during 2010-2014. The spatiotemporal Kriging technique, based on a quantitative characterization of soil heavy metal concentration variations in terms of non-separable variogram models, was employed to estimate the spatiotemporal soil heavy metal distribution in the study region. Our findings showed that the Cd, Cu, and Zn concentrations have an obvious incremental tendency from the southwestern to the central part of the study region. However, the Pb concentrations exhibited an obvious tendency from the northern part to the central part of the region. Then, spatial overlay analysis was used to obtain absolute and relative concentration increments of adjacent 1- or 5-year periods during 2010-2014. The spatial distribution of soil heavy metal concentration increments showed that the larger increments occurred in the center of the study region. Lastly, the principal component analysis combined with the multiple linear regression method were employed to quantify the source apportionment of the soil heavy metal concentration increments in the region. Our results led to the conclusion that the sources of soil heavy metal concentration increments should be ascribed to industry, agriculture and traffic. In particular, 82.5% of soil heavy metal concentration increment during 2010-2014 was ascribed to industrial/agricultural activities sources. Using STK and SOA to obtain the spatial distribution of heavy metal concentration increments in soils. Using PCA-MLR to quantify the source apportionment of soil heavy metal concentration increments. Copyright © 2017 Elsevier Ltd. All rights reserved.

Urban air-quality assessment and source apportionment studies for Bhubaneshwar, Odisha

NASA Astrophysics Data System (ADS)

Mahapatra, Parth Sarathi; Ray, Sanak; Das, Namrata; Mohanty, Ayusman; Ramulu, T. S.; Das, Trupti; Chaudhury, G. Roy; Das, S. N.

2013-04-01

Acid- and water-soluble component of suspended particulate matter was studied from January 2009 to December 2009 at Bhubaneshwar, an urban coastal location of eastern India, by high-volume sampler, environmental dust monitor using GRIMM®, and scanning electron microscope and energy dispersive X-ray spectrometer. The water-soluble components accounted for 30-45 % of the total suspended particulate matter, and the major elements were observed to be ammonium and nitrate as the cationic and anionic species, respectively. The acid-soluble component like copper, nickel, cobalt, iron, and lead accounted for 5-15 % of the total particulate matter concentration. The composition of particulate matter shows a clear seasonal variation in relation to wind speed, wind direction, and trajectories of the air mass movement. The GRIMM spectrometer analysis shows higher concentration of fine particulate matter. Source apportionment and enrichment factor analysis indicated that except sodium and chloride, all other elements have emerged from different sources such as crustal as well as anthropogenic.

Spatially and chemically resolved source apportionment analysis: Case study of high particulate matter event

NASA Astrophysics Data System (ADS)

Kim, Byeong-Uk; Bae, Changhan; Kim, Hyun Cheol; Kim, Eunhye; Kim, Soontae

2017-08-01

This article presents the results of a detailed source apportionment study of the high particulate matter (PM) event in the Seoul Metropolitan Area (SMA), South Korea, during late February 2014. Using the Comprehensive Air Quality Model with Extensions with its Particulate Source Apportionment Technology (CAMx-PSAT), we defined 10 source regions, including five in China, for spatially and chemically resolved analyses. During the event, the spatially averaged PM10 concentration at all PM10 monitors in the SMA was 129 μg/m3, while the PM10 and PM2.5 concentrations at the BulGwang Supersite were 143 μg/m3 and 123 μg/m3, respectively. CAMx-PSAT showed reasonably good PM model performance in both China and the SMA. For February 23-27, CAMx-PSAT estimated that Chinese contributions to the SMA PM10 and PM2.5 were 84.3 μg/m3 and 80.0 μg/m3, respectively, or 64% and 70% of the respective totals, while South Korea's respective domestic contributions were 36.5 μg/m3 and 23.3 μg/m3. We observed that the spatiotemporal pattern of PM constituent concentrations and contributions did not necessarily follow that of total PM10 and PM2.5 concentrations. For example, Beijing-Tianjin-Hebei produced high nitrate concentrations, but the two most-contributing regions to PM in the SMA were the Near Beijing area and South Korea. In addition, we noticed that the relative contributions from each region changed over time. We found that most ammonium mass that neutralized Chinese sulfate mass in the SMA came from South Korean sources, indicating that secondary inorganic aerosol in the SMA, especially ammonium sulfates, during this event resulted from different major precursors originating from different regions.

Distribution and source apportionment of polycyclic aromatic hydrocarbons in surface sediments from Zhoushan Archipelago and Xiangshan Harbor, East China Sea.

PubMed

Wang, Xiaoyan; Xu, Huanzhi; Zhou, Yongdong; Wu, Changwen; Kanchanopas-Barnette, Praparsiri

2015-12-30

Zhoushan Archipelago and the adjacent Xiangshan Harbor are important commercial, tourism, fishing, and mariculture areas. Considering the concern on the effects of anthropogenic activities on the environment, the level and source apportionment of polycyclic aromatic hydrocarbons (PAHs) in surface sediments were investigated. The sum of 16 PAH (∑16 PAH) concentrations in the Zhoushan Archipelago ranged from 3.67 to 31.30 ng g(-1) d.w., with a mean of 15.01 ± 1.21 ng g(-1) d.w., and that in Xiangshan Harbor varied from 11.58 to 481.44 ng g(-1) d.w., with a mean of 62.52 ± 32.85 ng g(-1) d.w. Diagnostic ratios and factor analysis were performed to identify PAH sources. Results show that PAHs have mixed origins (i.e., traffic-related sources, coal combustion, petrogenic sources, and biomass burning), with pyrolytic-related pollution as the dominant source. This study provided a baseline to promote environmental protection and pollution episode monitoring in the East China Sea. Copyright © 2015 Elsevier Ltd. All rights reserved.

The CSSIAR v.1.00 Software: A new tool based on SIAR to assess soil redistribution using Compound Specific Stable Isotopes

NASA Astrophysics Data System (ADS)

Sergio, de los Santos-Villalobos; Claudio, Bravo-Linares; dos Anjos Roberto, Meigikos; Renan, Cardoso; Max, Gibbs; Andrew, Swales; Lionel, Mabit; Gerd, Dercon

Soil erosion is one of the biggest challenges for food production around the world. Many techniques have been used to evaluate and mitigate soil degradation. Nowadays isotopic techniques are becoming a powerful tool to assess soil apportionment. One of the innovative techniques used is the Compound Specific Stable Isotopes (CSSI) analysis, which has been used to track down sediments and specify their sources by the isotopic signature of δ13 C in specific fatty acids. The application of this technique on soil apportionment has been recently developed, however there is a lack of user-friendly Software for data processing and interpretation. The aim of this article is to introduce a new open source tool for working with data sets generated by the use of the CSSI technique to assess soil apportionment, called the CSSIARv1.00 Software

Spatio-temporal patterns and source apportionment of pollution in Qiantang River (China) using neural-based modeling and multivariate statistical techniques

NASA Astrophysics Data System (ADS)

Su, Shiliang; Zhi, Junjun; Lou, Liping; Huang, Fang; Chen, Xia; Wu, Jiaping

Characterizing the spatio-temporal patterns and apportioning the pollution sources of water bodies are important for the management and protection of water resources. The main objective of this study is to describe the dynamics of water quality and provide references for improving river pollution control practices. Comprehensive application of neural-based modeling and different multivariate methods was used to evaluate the spatio-temporal patterns and source apportionment of pollution in Qiantang River, China. Measurement data were obtained and pretreated for 13 variables from 41 monitoring sites for the period of 2001-2004. A self-organizing map classified the 41 monitoring sites into three groups (Group A, B and C), representing different pollution characteristics. Four significant parameters (dissolved oxygen, biochemical oxygen demand, total phosphorus and total lead) were identified by discriminant analysis for distinguishing variations of different years, with about 80% correct assignment for temporal variation. Rotated principal component analysis (PCA) identified four potential pollution sources for Group A (domestic sewage and agricultural pollution, industrial wastewater pollution, mineral weathering, vehicle exhaust and sand mining), five for Group B (heavy metal pollution, agricultural runoff, vehicle exhaust and sand mining, mineral weathering, chemical plants discharge) and another five for Group C (vehicle exhaust and sand mining, chemical plants discharge, soil weathering, biochemical pollution, mineral weathering). The identified potential pollution sources explained 75.6% of the total variances for Group A, 75.0% for Group B and 80.0% for Group C, respectively. Receptor-based source apportionment was applied to further estimate source contributions for each pollution variable in the three groups, which facilitated and supported the PCA results. These results could assist managers to develop optimal strategies and determine priorities for river pollution control and effective water resources management.

Biomass burning contributed most to the human cancer risk exposed to the soil-bound PAHs from Chengdu Economic Region, western China.

PubMed

Zheng, Huang; Xing, Xinli; Hu, Tianpeng; Zhang, Yuan; Zhang, Jiaquan; Zhu, Gehao; Li, Ying; Qi, Shihua

2018-05-03

The purpose of this study was to assess the human cancer risk due to the exposure to the soil-bound polycyclic aromatic hydrocarbons (PAHs) from Chengdu Economic Region (CER), western China with the main concern on cancer risk source apportionment. The total concentrations of sixteen PAHs ranged from 12.5 to 75431 ng g -1 , with a mean value of 3106 ng g -1 , which suggested that the most areas of CER were contaminated. Source apportionment of PAHs was conducted by the positive matrix factorization (PMF) model and the biomass burning contributed most (63.6%) to the total PAHs, followed by petroleum combustion (16.0%), coke source (11.3%), and petrogenic source (9.2%). Results from incremental lifetime cancer risk (ILCR) calculation showed that soil ingestion exerted the highest cancer risk (accounted for 98.1 - 99.3% of the total cancer risk) on human health among three different exposure pathways, followed by dermal contact (0.66 - 1.83%) and inhalation (0.03 - 0.04%). Among different age groups, adult suffered the highest cancer risk via any exposure pathways. Based on PMF and ILCR methods, the cancer risk source apportionment was conducted and the biomass burning showed moderate cancer risk. The petrogenic, coke, and petroleum sources showed low cancer risks to human. To analyze the sensitivity of the parameters used in ILCR calculation, Monte Carlo simulation was employed. The results indicated that the contribution of each source and exposure duration (ED) were the influential parameters on human health associated with soil-bound PAHs. Therefore, much attentions should be paid to biomass burning to avoid cumulative cancer risk. Copyright © 2018 Elsevier Inc. All rights reserved.

Chemometric techniques in distribution, characterisation and source apportionment of polycyclic aromatic hydrocarbons (PAHS) in aquaculture sediments in Malaysia.

PubMed

Retnam, Ananthy; Zakaria, Mohamad Pauzi; Juahir, Hafizan; Aris, Ahmad Zaharin; Zali, Munirah Abdul; Kasim, Mohd Fadhil

2013-04-15

This study investigated polycyclic aromatic hydrocarbons (PAHs) pollution in surface sediments within aquaculture areas in Peninsular Malaysia using chemometric techniques, forensics and univariate methods. The samples were analysed using soxhlet extraction, silica gel column clean-up and gas chromatography mass spectrometry. The total PAH concentrations ranged from 20 to 1841 ng/g with a mean of 363 ng/g dw. The application of chemometric techniques enabled clustering and discrimination of the aquaculture sediments into four groups according to the contamination levels. A combination of chemometric and molecular indices was used to identify the sources of PAHs, which could be attributed to vehicle emissions, oil combustion and biomass combustion. Source apportionment using absolute principle component scores-multiple linear regression showed that the main sources of PAHs are vehicle emissions 54%, oil 37% and biomass combustion 9%. Land-based pollution from vehicle emissions is the predominant contributor of PAHs in the aquaculture sediments of Peninsular Malaysia. Copyright © 2013 Elsevier Ltd. All rights reserved.

ENVIRONMENTAL APPLICATIONS OF NOVEL INSTRUMENTATION FOR MEASUREMENT OF LEAD ISOTOPE RATIOS IN ATMOSPHERIC POLLUTION SOURCE APPORTIONMENT STUDIES

EPA Science Inventory

In spite of the reduced flux of lead to the atmosphere from the combustion of leaded gasoline, anthropogenic sources still dominate the supply of lead to the atmosphere and the environment. Emissions from coal and oil combustion, industrial processes, and municipal incineration w...

Heavy metal contamination status and source apportionment in sediments of Songhua River Harbin region, Northeast China.

PubMed

Li, Ning; Tian, Yu; Zhang, Jun; Zuo, Wei; Zhan, Wei; Zhang, Jian

2017-02-01

The Songhua River represents one of the seven major river systems in China. It flows through Harbin city with 66 km long, locating in the northern China with a longer winter time. This paper aimed to study concentration distributions, stability, risk assessment, and source apportionment of heavy metals including chromium (Cr), cadmium (Cd), lead (Pb), mercury (Hg), arsenic (As), copper (Cu), zinc (Zn), and nickel (Ni) in 11 selected sections of the Songhua River Harbin region. Results showed that Cr, Cd, Pb, Hg, and As exceeded their respective geochemical background values in sediments of most monitoring sections. Compared with other important rivers and lakes in China, Cr, Hg, Cd, and As pollutions in surface sediments were above medium level. Further analysis of chemical speciation indicated that Cr and As in surface sediments were relatively stable while Pb and Cd were easily bioavailable. Correlation analysis revealed sources of these metals except As might be identical. Pollution levels and ecological risks of heavy metals in surface sediments presented higher in the mainstream region (45° 47.0' N ~ 45° 53.3' N, 126° 37.0' E ~ 126° 42.1' E). Source apportionment found Hejiagou and Ashi River were the main contributors to metal pollution of this region. Thus, anthropogenic activities along the Hejiagou and Ashi River should be restricted in order to protect the Songhua River Harbin region from metal contamination.

ACTRIS ACSM intercomparison - Part 2: Intercomparison of ME-2 organic source apportionment results from 15 individual, co-located aerosol mass spectrometers

NASA Astrophysics Data System (ADS)

Fröhlich, R.; Crenn, V.; Setyan, A.; Belis, C. A.; Canonaco, F.; Favez, O.; Riffault, V.; Slowik, J. G.; Aas, W.; Aijälä, M.; Alastuey, A.; Artiñano, B.; Bonnaire, N.; Bozzetti, C.; Bressi, M.; Carbone, C.; Coz, E.; Croteau, P. L.; Cubison, M. J.; Esser-Gietl, J. K.; Green, D. C.; Gros, V.; Heikkinen, L.; Herrmann, H.; Jayne, J. T.; Lunder, C. R.; Minguillón, M. C.; Močnik, G.; O'Dowd, C. D.; Ovadnevaite, J.; Petralia, E.; Poulain, L.; Priestman, M.; Ripoll, A.; Sarda-Estève, R.; Wiedensohler, A.; Baltensperger, U.; Sciare, J.; Prévôt, A. S. H.

2015-02-01

Chemically resolved atmospheric aerosol data sets from the largest intercomparison of the Aerodyne aerosol chemical speciation monitors (ACSM) performed to date were collected at the French atmospheric supersite SIRTA. In total 13 quadrupole ACSMs (Q-ACSM) from the European ACTRIS ACSM network, one time-of-flight ACSM (ToF-ACSM), and one high-resolution ToF aerosol mass spectrometer (AMS) were operated in parallel for about three weeks in November and December 2013. Part 1 of this study reports on the accuracy and precision of the instruments for all the measured species. In this work we report on the intercomparison of organic components and the results from factor analysis source apportionment by positive matrix factorisation (PMF) utilising the multilinear engine 2 (ME-2). Except for the organic contribution of m/z 44 to the total organics (f44), which varied by factors between 0.6 and 1.3 compared to the mean, the peaks in the organic mass spectra were similar among instruments. The m/z 44 differences in the spectra resulted in a variable f44 in the source profiles extracted by ME-2, but had only a minor influence on the extracted mass contributions of the sources. The presented source apportionment yielded four factors for all 15 instruments: hydrocarbon-like organic aerosol (HOA), cooking-related organic aerosol (COA), biomass burning-related organic aerosol (BBOA) and secondary oxygenated organic aerosol (OOA). Individual application and optimisation of the ME-2 boundary conditions (profile constraints) are discussed together with the investigation of the influence of alternative anchors (reference profiles). A comparison of the ME-2 source apportionment output of all 15 instruments resulted in relative SD from the mean between 13.7 and 22.7% of the source's average mass contribution depending on the factors (HOA: 14.3 ± 2.2%, COA: 15.0 ± 3.4%, OOA: 41.5 ± 5.7%, BBOA: 29.3 ± 5.0%). Factors which tend to be subject to minor factor mixing (in this case COA) have higher relative uncertainties than factors which are recognised more readily like the OOA. Averaged over all factors and instruments the relative first SD from the mean of a source extracted with ME-2 was 17.2%.

Tracing carbonaceous sources by using particulate carbon and sulfate in precipitation in Calgary, Alberta Canada

NASA Astrophysics Data System (ADS)

Ge, C.; Stenhouse, K. J.; Du, K.; Xing, Z.; Norman, A. L.

2016-12-01

Carbonaceous matter is often the dominant contributor to Particulate Matter (PM) which has a significant influence on climate, air quality and human health. The measurement of particulate carbon in rainfall in Calgary, Alberta has not been studied. This study reports the sulfate and the first concentrations of particulate carbon (PC) in rainfall in Calgary. It traces seasonal carbonaceous sources for the purpose of understanding sources for air quality control. Precipitation samples are collected twice a day at the University of Calgary. Thermo-optical methods are used to analyze concentrations of PC, including elemental carbon (EC), primary organic carbon (POC) and secondary organic carbon (SOC). Sulfate concentrations are measured using ion chromatography. In this study, sources from long range transport and local emissions are examined. We emphasized the apportionment of OC/EC in oil and gas emissions and diurnal variations in transportation emissions. Weekly average data for dry deposition were calculated to estimate the scavenging ratio of EC/POC/SOC and ions in precipitation. The results of this study will be presented with an emphasis on the relationship of carbonaceous material and sulfate. A range of apportionment methods have been applied to examine limitations in quantifying SOC in fall.

Countering Air and Missile Threats

DTIC Science & Technology

2012-03-23

information is estimated to average 1 hour per response, including the time for reviewing instructions, searching existing data sources , gathering... apportionment guidance by the JFC. Functional component commands serve to ease the burden on the theater and joint task force staffs, free the JFC to focus...action (COA) to attain the desired objectives. Counterair requires a combination of OCA and DCA operations based on the JFC’s air apportionment

Characterization of Arctic elemental carbon in Barrow, AK using radiocarbon source apportionment

NASA Astrophysics Data System (ADS)

Barrett, T. E.; Usenko, S.; Robinson, E. M.; Sheesley, R. J.

2013-12-01

Currently, the Arctic is one of the fastest warming regions on earth with surface temperatures increasing at a rate nearly double the global mean over recent decades. Despite the fact that atmospheric concentrations of elemental carbon (EC) are lower in the Arctic than in lower latitudes, deposition of EC on snow and ice may exacerbate regional warming by simultaneously decreasing albedo and increasing melt rates. Due to the intensifying Arctic oil exploration in areas such as the Beaufort and Chukchi seas, the impact of new emission sources such as heavy fuel and heavy diesel combustion on regional carbon needs to be assessed. The first step in developing mitigation strategies for reducing current and future EC emissions in the Arctic is to determine emission source contributions. This study aims to determine the relative contributions of fossil fuel and biomass combustion and to identify major source regions of EC to the Arctic. Radiocarbon analysis of both total organic carbon (TOC) and EC combined with organic tracer and back trajectory analysis has been applied to a set of wintertime coarse particulate matter (PM10) samples from Barrow, AK. Preliminary apportionment for January 2013 indicates roughly half of TOC is from biogenic/biomass burning emissions and one third of EC is due to biomass burning emissions. The radiocarbon results will be combined with organic tracer analysis (polycyclic aromatic hydrocarbons, petroleum biomarkers and normal alkanes), increasing the specificity of the relative contribution of both the fossil and modern (biogenic/biomass burning) carbon emission sources. This research represents the first reported radiocarbon values for Arctic EC, providing highly conclusive source apportionment prior to the influence of increased drilling operations and ship traffic in the Beaufort and Chukchi seas.

Source apportionment of trace metals in river sediments: A comparison of three methods.

PubMed

Chen, Haiyang; Teng, Yanguo; Li, Jiao; Wu, Jin; Wang, Jinsheng

2016-04-01

Increasing trace metal pollution in river sediment poses a significant threat to watershed ecosystem health. Identifying potential sources of sediment metals and apportioning their contributions are of key importance for proposing prevention and control strategies of river pollution. In this study, three advanced multivariate receptor models, factor analysis with nonnegative constraints (FA-NNC), positive matrix factorization (PMF), and multivariate curve resolution weighted-alternating least-squares (MCR-WALS), were comparatively employed for source apportionment of trace metals in river sediments and applied to the Le'an River, a main tributary of Poyang Lake which is the largest freshwater lake in China. The pollution assessment with contamination factor and geoaccumulation index suggested that the river sediments in Le'an River were contaminated severely by trace metals due to human activities. With the three apportionment tools, similar source profiles of trace metals in sediments were extracted. Especially, the MCR-WALS and PMF models produced essentially the same results. Comparatively speaking, the weighted schemes might give better solutions than the unweighted FA-NNC because the uncertainty information of environmental data was considered by PMF and MCR-WALS. Anthropogenic sources were apportioned as the most important pollution sources influencing the sediment metals in Le'an River with contributions of about 90%. Among them, copper tailings occupied the largest contribution (38.4-42.2%), followed by mining wastewater (29.0-33.5%), and agricultural activities (18.2-18.7%). To protect the ecosystem of Le'an River and Poyang Lake, special attention should be paid to the discharges of mining wastewater and the leachates of copper tailing ponds in that region. Copyright © 2015 Elsevier Ltd. All rights reserved.

Source identification and apportionment of halogenated compounds observed at a remote site in East Asia.

PubMed

Li, Shanlan; Kim, Jooil; Park, Sunyoung; Kim, Seung-Kyu; Park, Mi-Kyung; Mühle, Jens; Lee, Gangwoong; Lee, Meehye; Jo, Chun Ok; Kim, Kyung-Ryul

2014-01-01

The sources of halogenated compounds in East Asia associated with stratospheric ozone depletion and climate change are relatively poorly understood. High-precision in situ measurements of 18 halogenated compounds and carbonyl sulfide (COS) made at Gosan, Jeju Island, Korea, from November 2007 to December 2011 were analyzed by a positive matrix factorization (PMF). Seven major industrial sources were identified from the enhanced concentrations of halogenated compounds observed at Gosan and corresponding concentration-based source contributions were also suggested: primary aluminum production explaining 37% of total concentration enhancements, solvent usage of which source apportionment is 25%, fugitive emissions from HCFC/HFC production with 11%, refrigerant replacements (9%), semiconductor/electronics industry (9%), foam blowing agents (6%), and fumigation (3%). Statistical trajectory analysis was applied to specify the potential emission regions for seven sources using back trajectories. Primary aluminum production, solvent usage and fugitive emission sources were mainly contributed by China. Semiconductor/electronics sources were dominantly located in Korea. Refrigerant replacement, fumigation and foam blowing agent sources were spread throughout East Asian countries. The specified potential source regions are consistent with country-based consumptions and emission patterns, verifying the PMF analysis results. The industry-based emission sources of halogenated compounds identified in this study help improve our understanding of the East Asian countries' industrial contributions to halogenated compound emissions.

SOURCE APPORTIONMENT STUDIES OF PM-2.5 IN TWO CZECH CITIES: POSSIBLE USES IN HEALTH STUDIES

EPA Science Inventory

Aerosol and gas phase air pollutant measurements were made in two cities during an ongoing air pollution-health outcome study in the Czech Republic. Teplice, located in northwestern Bohemia, was selected because the local population was exposed to high air pollution levels. Prac...

IMPLICATIONS OF PARTICULATE MATTER RESEARCH PROGRAM UPON EXPOSURE ASSESSMENT AND APPORTIONMENT AND ATTRIBUTION OF ENVIRONMENTAL EFFECTS

EPA Science Inventory

Recent personal exposure panel studies and monitoring programs addressing fine particulate matter (PM) and associated co-pollutants have elucidated the physical and statistical relationships between personal exposures, residential indoor concentrations (and sources), concentratio...

Organic aerosol source apportionment by offline-AMS over a full year in Marseille

NASA Astrophysics Data System (ADS)

Bozzetti, Carlo; El Haddad, Imad; Salameh, Dalia; Daellenbach, Kaspar Rudolf; Fermo, Paola; Gonzalez, Raquel; Cruz Minguillón, María; Iinuma, Yoshiteru; Poulain, Laurent; Elser, Miriam; Müller, Emanuel; Gates Slowik, Jay; Jaffrezo, Jean-Luc; Baltensperger, Urs; Marchand, Nicolas; Prévôt, André Stephan Henry

2017-07-01

We investigated the seasonal trends of OA sources affecting the air quality of Marseille (France), which is the largest harbor of the Mediterranean Sea. This was achieved by measurements of nebulized filter extracts using an aerosol mass spectrometer (offline-AMS). In total 216 PM2. 5 (particulate matter with an aerodynamic diameter < 2.5 µm) filter samples were collected over 1 year from August 2011 to July 2012. These filters were used to create 54 composite samples which were analyzed by offline-AMS. The same samples were also analyzed for major water-soluble ions, metals, elemental and organic carbon (EC / OC), and organic markers, including n-alkanes, hopanes, polycyclic aromatic hydrocarbons (PAHs), lignin and cellulose pyrolysis products, and nitrocatechols. The application of positive matrix factorization (PMF) to the water-soluble AMS spectra enabled the extraction of five factors, related to hydrocarbon-like OA (HOA), cooking OA (COA), biomass burning OA (BBOA), oxygenated OA (OOA), and an industry-related OA (INDOA). Seasonal trends and relative contributions of OA sources were compared with the source apportionment of OA spectra collected from the AMS field deployment at the same station but in different years and for shorter monitoring periods (February 2011 and July 2008). Online- and offline-AMS source apportionment revealed comparable seasonal contribution of the different OA sources. Results revealed that BBOA was the dominant source during winter, representing on average 48 % of the OA, while during summer the main OA component was OOA (63 % of OA mass on average). HOA related to traffic emissions contributed on a yearly average 17 % to the OA mass, while COA was a minor source contributing 4 %. The contribution of INDOA was enhanced during winter (17 % during winter and 11 % during summer), consistent with an increased contribution from light alkanes, light PAHs (fluoranthene, pyrene, phenanthrene), and selenium, which is commonly considered as a unique coal combustion and coke production marker. Online- and offline-AMS source apportionments revealed evolving levoglucosan : BBOA ratios, which were higher during late autumn and March. A similar seasonality was observed in the ratios of cellulose combustion markers to lignin combustion markers, highlighting the contribution from cellulose-rich biomass combustion, possibly related to agricultural activities.

Nested Source Apportionment of Secondary Inorganic Aerosol over Yangtze River Delta during Heavy Haze Episodes

NASA Astrophysics Data System (ADS)

Luo, L.; Cheng, Z.

2017-12-01

Secondary inorganic aerosols (SNA), i.e., sulfate, nitrate and ammonium, account for over 50% of fine particulate matter (PM2.5) during heavy haze episodes over Yangtze River Delta (YRD) region of China. Understanding the origin and transport of SNA is crucial for alleviating haze pollution over YRD. The long range transport from outer-YRD regions had significant influence on SNA during haze episodes over YRD, especially in winter. However, previous studies only using single domain for source analysis are limited on quantifying the local and transported sources in province scale altogether. In this study, the Integrated Source Apportionment Method (ISAM) based on the Weather Research and Forecasting and Community Multi-scale Air Quality (WRF-CMAQ) models was performed to two nested domains, one covering east of China and the other embracing YRD, for source apportionment of SNA in YRD during January, 2015. The results indicated that the outer-YRD transport mainly from upwind northwestern provinces, Shandong and Henan, was the dominant contributor accounting for 36.2% of sulfate during pollution episodes. For nitrate, inner-YRD and outer-YRD transport were the two evenly major regional sources, contributing 51.9% of nitrate during hazes. However, local accumulation was the first contributor accounting for 73.9% of ammonium. The long lifetime of formation process for sulfate and nitrate caused the conspicuous transport effect driven by wind when adjacent regions under severe pollution. Although the total effects of long and short distant transport played a major role for the level of sulfate and nitrate, the extent of contribution from local accumulation was similar with them even larger in province scale. Industry followed by power plant were two principal sources of sulfate for all three types of regional contribution. The main sectoral sources of nitrate were industry and transport for local accumulation while power plant besides them for inner-YRD and outer-YRD transport. For ammonium, volatile sources were major origin for local accumulation while agriculture for inner-YRD transport. These results demonstrate the importance for outer-YRD control during haze episodes for sulfate and nitrate while local emission control for ammonium in YRD.

Sources of particulate matter in China: Insights from source apportionment studies published in 1987-2017.

PubMed

Zhu, Yanhong; Huang, Lin; Li, Jingyi; Ying, Qi; Zhang, Hongliang; Liu, Xingang; Liao, Hong; Li, Nan; Liu, Zhenxin; Mao, Yuhao; Fang, Hao; Hu, Jianlin

2018-06-01

Particulate matter (PM) in the atmosphere has adverse effects on human health, ecosystems, and visibility. It also plays an important role in meteorology and climate change. A good understanding of its sources is essential for effective emission controls to reduce PM and to protect public health. In this study, a total of 239 PM source apportionment studies in China published during 1987-2017 were reviewed. The documents studied include peer-reviewed papers in international and Chinese journals, as well as degree dissertations. The methods applied in these studies were summarized and the main sources in various regions of China were identified. The trends of source contributions at two major cities with abundant studies over long-time periods were analyzed. The most frequently used methods for PM source apportionment in China are receptor models, including chemical mass balance (CMB), positive matrix factorization (PMF), and principle component analysis (PCA). Dust, fossil fuel combustion, transportation, biomass burning, industrial emission, secondary inorganic aerosol (SIA) and secondary organic aerosol (SOA) are the main source categories of fine PM identified in China. Even though the sources of PM vary among seven different geographical areas of China, SIA, industrial, and dust emissions are generally found to be the top three source categories in 2007-2016. A number of studies investigated the sources of SIA and SOA in China using air quality models and indicated that fossil fuel combustion and industrial emissions were the most important sources of SIA (total contributing 63.5%-88.1% of SO 4 2- , and 47.3%-70% NO 3 - ), and agriculture emissions were the dominant source of NH 4 + (contributing 53.9%-90%). Biogenic emissions were the most important source of SOA in China in summer, while residential and industrial emissions were important in winter. Long-term changes of PM sources at two megacities of Beijing and Nanjing indicated that the contributions of fossil fuel and industrial sources have been declining after stricter emission controls in recent years. In general, dust and industrial contributions decreased and transportation contributions increased after 2000. PM 2.5 emissions are predicted to decline in most regions during 2005-2030, even though the energy consumptions except biomass burning are predicted to continue to increase. Industrial, residential, and biomass burning sources will become more important in the future in the businuess-as-usual senarios. This review provides valuable information about main sources of PM and their trends in China. A few recommendations are suggested to further improve our understanding the sources and to develop effective PM control strategies in various regions of China. Copyright © 2018 Elsevier Ltd. All rights reserved.

Identification and characterization of fine and coarse particulate matter sources in a middle-European urban environment

NASA Astrophysics Data System (ADS)

Kertész, Zs.; Szoboszlai, Z.; Angyal, A.; Dobos, E.; Borbély-Kiss, I.

2010-06-01

In this work a source apportionment study is presented which aimed to characterize the PM 2.5 and PM 2.5-10 sources in the urban area of Debrecen, East-Hungary by using streaker samples, IBA methods and positive matrix factorization (PMF) analysis. Samples of fine (PM 2.5) and coarse (PM 2.5-10) urban particulate matter were collected with 2 h time resolution in the frame of five sampling campaigns during 2007-2009 in different seasons in the downtown of Debrecen. Elemental concentrations from Al to Pb of over 1000 samples were obtained by particle induced X-ray emission (PIXE); concentrations of black carbon (BC) were determined with a smoke stain reflectometer. On this data base source apportionment was carried out by using the PMF method. Seven factors were identified for both size fractions, including soil dust, traffic, secondary aerosol - sulphates, domestic heating, oil combustion, agriculture and an unknown factor enriched with chlorine. Seasonal and daily variation of the different factors was studied as well as their dependence on meteorological parameters. Besides determining the time patterns characteristic to the city, several emission episodes were identified including a Saharan dust intrusion on 21st-24th May, 2008.

FORT HALL SOURCE APPORTIONMENT STUDY (FINAL REPORT)

EPA Science Inventory

Air quality monitoring on the Fort Hall Indian Reservation has revealed numerous exceedances of the National Ambient Air Quality Standard (NAAQS) for 24-h averaged PM10 mass. Wind-directional analysis coupled with PM10 measurements have identified the FMC elemental phosphorus p...

Levels and source apportionment of children's lead exposure: could urinary lead be used to identify the levels and sources of children's lead pollution?

PubMed

Cao, Suzhen; Duan, Xiaoli; Zhao, Xiuge; Wang, Beibei; Ma, Jin; Fan, Delong; Sun, Chengye; He, Bin; Wei, Fusheng; Jiang, Guibin

2015-04-01

As a highly toxic heavy metal, the pollution and exposure risks of lead are of widespread concern for human health. However, the collection of blood samples for use as an indicator of lead pollution is not always feasible in most cohort or longitudinal studies, especially those involving children health. To evaluate the potential use of urinary lead as an indicator of exposure levels and source apportionment, accompanying with environmental media samples, lead concentrations and isotopic measurements (expressed as (207)Pb/(206)Pb, (208)Pb/(206)Pb and (204)Pb/(206)Pb) were investigated and compared between blood and urine from children living in the vicinities of a typical coking plant and lead-acid battery factory. The results showed urinary lead might not be a preferable proxy for estimating blood lead levels. Fortunately, urinary lead isotopic measurements could be used as an alternative for identifying the sources of children's lead exposure, which coincided well with the blood lead isotope ratio analysis. Copyright © 2015 Elsevier Ltd. All rights reserved.

Source apportionment of ambient non-methane hydrocarbons in Hong Kong: application of a principal component analysis/absolute principal component scores (PCA/APCS) receptor model.

PubMed

Guo, H; Wang, T; Louie, P K K

2004-06-01

Receptor-oriented source apportionment models are often used to identify sources of ambient air pollutants and to estimate source contributions to air pollutant concentrations. In this study, a PCA/APCS model was applied to the data on non-methane hydrocarbons (NMHCs) measured from January to December 2001 at two sampling sites: Tsuen Wan (TW) and Central & Western (CW) Toxic Air Pollutants Monitoring Stations in Hong Kong. This multivariate method enables the identification of major air pollution sources along with the quantitative apportionment of each source to pollutant species. The PCA analysis identified four major pollution sources at TW site and five major sources at CW site. The extracted pollution sources included vehicular internal engine combustion with unburned fuel emissions, use of solvent particularly paints, liquefied petroleum gas (LPG) or natural gas leakage, and industrial, commercial and domestic sources such as solvents, decoration, fuel combustion, chemical factories and power plants. The results of APCS receptor model indicated that 39% and 48% of the total NMHCs mass concentrations measured at CW and TW were originated from vehicle emissions, respectively. 32% and 36.4% of the total NMHCs were emitted from the use of solvent and 11% and 19.4% were apportioned to the LPG or natural gas leakage, respectively. 5.2% and 9% of the total NMHCs mass concentrations were attributed to other industrial, commercial and domestic sources, respectively. It was also found that vehicle emissions and LPG or natural gas leakage were the main sources of C(3)-C(5) alkanes and C(3)-C(5) alkenes while aromatics were predominantly released from paints. Comparison of source contributions to ambient NMHCs at the two sites indicated that the contribution of LPG or natural gas at CW site was almost twice that at TW site. High correlation coefficients (R(2) > 0.8) between the measured and predicted values suggested that the PCA/APCS model was applicable for estimation of sources of NMHCs in ambient air.

Source apportionment and a novel approach of estimating regional contributions to ambient PM2.5 in Haikou, China.

PubMed

Liu, Baoshuang; Li, Tingkun; Yang, Jiamei; Wu, Jianhui; Wang, Jiao; Gao, Jixin; Bi, Xiaohui; Feng, Yinchang; Zhang, Yufen; Yang, Haihang

2017-04-01

A novel approach was developed to estimate regional contributions to ambient PM 2.5 in Haikou, China. In this paper, the investigation was divided into two main steps. The first step: analysing the characteristics of the chemical compositions of ambient PM 2.5 , as well as the source profiles, and then conducting source apportionments by using the CMB and CMB-Iteration models. The second step: the development of estimation approaches for regional contributions in terms of local features of Haikou and the results of source apportionment, and estimating regional contributions to ambient PM 2.5 in Haikou by this new approach. The results indicate that secondary sulphate, resuspended dust and vehicle exhaust were the major sources of ambient PM 2.5 in Haikou, contributing 9.9-21.4%, 10.1-19.0% and 10.5-20.2%, respectively. Regional contributions to ambient PM 2.5 in Haikou in spring, autumn and winter were 22.5%, 11.6% and 32.5%, respectively. The regional contribution in summer was assumed to be zero according to the better atmospheric quality and assumptions of this new estimation approach. The higher regional contribution in winter might be mainly attributable to the transport of polluted air originating in mainland China, especially from the north, where coal is burned for heating in winter. Copyright © 2017 Elsevier Ltd. All rights reserved.

Contribution of regional-scale fire events to ozone and PM2.5 ...

EPA Pesticide Factsheets

Two specific fires from 2011 are tracked for local to regional scale contribution to ozone (O3) and fine particulate matter (PM2.5) using a freely available regulatory modeling system that includes the BlueSky wildland fire emissions tool, Spare Matrix Operator Kernel Emissions (SMOKE) model, Weather and Research Forecasting (WRF) meteorological model, and Community Multiscale Air Quality (CMAQ) photochemical grid model. The modeling system was applied to track the contribution from a wildfire (Wallow) and prescribed fire (Flint Hills) using both source sensitivity and source apportionment approaches. The model estimated fire contribution to primary and secondary pollutants are comparable using source sensitivity (brute-force zero out) and source apportionment (Integrated Source Apportionment Method) approaches. Model estimated O3 enhancement relative to CO is similar to values reported in literature indicating the modeling system captures the range of O3 inhibition possible near fires and O3 production both near the fire and downwind. O3 and peroxyacetyl nitrate (PAN) are formed in the fire plume and transported downwind along with highly reactive VOC species such as formaldehyde and acetaldehyde that are both emitted by the fire and rapidly produced in the fire plume by VOC oxidation reactions. PAN and aldehydes contribute to continued downwind O3 production. The transport and thermal decomposition of PAN to nitrogen oxides (NOX) enables O3 production in areas

Source apportionment of visual impairment during the California regional PM 10/PM 2.5 air quality study

NASA Astrophysics Data System (ADS)

Chen, Jianjun; Ying, Qi; Kleeman, Michael J.

2009-12-01

Gases and particulate matter predictions from the UCD/CIT air quality model were used in a visibility model to predict source contributions to visual impairment in the San Joaquin Valley (SJV), the southern portion of California's Central Valley, during December 2000 and January 2001. Within the SJV, daytime (0800-1700 PST) light extinction was dominated by scattering associated with airborne particles. Measured daytime particle scattering coefficients were compared to predicted values at approximately 40 locations across the SJV after correction for the increased temperature and decreased relative humidity produced by "smart heaters" placed upstream of nephelometers. Mean fractional bias and mean fractional error were -0.22 and 0.65, respectively, indicating reasonable agreement between model predictions and measurements. Particulate water, nitrate, organic matter, and ammonium were the major particulate species contributing to light scattering in the SJV. Daytime light extinction in the SJV averaged between December 25, 2000 and January 7, 2001 was mainly associated with animal ammonia sources (28%), diesel engines (18%), catalyst gasoline engines (9%), other anthropogenic sources (9%), and wood smoke (7%) with initial and boundary conditions accounting for 13%. The source apportionment results from this study apply to wintertime conditions when airborne particulate matter concentrations are typically at their annual maximum. Further study would be required to quantify source contributions to light extinction in other seasons.

Microbial source tracking: a forensic technique for microbial source identification?

PubMed

Stapleton, Carl M; Wyer, Mark D; Kay, David; Crowther, John; McDonald, Adrian T; Walters, Martin; Gawler, Andrew; Hindle, Terry

2007-05-01

As the requirements of the Water Framework Directive (WFD) and the US Clean Water Act (USCWA) for the maintenance of microbiological water quality in 'protected areas' highlight, there is a growing recognition that integrated management of point and diffuse sources of microbial pollution is essential. New information on catchment microbial dynamics and, in particular, the sources of faecal indicator bacteria found in bathing and shellfish harvesting waters is a pre-requisite for the design of any 'programme of measures' at the drainage basin scale to secure and maintain compliance with existing and new health-based microbiological standards. This paper reports on a catchment-scale microbial source tracking (MST) study in the Leven Estuary drainage basin, northwest England, an area for which quantitative faecal indicator source apportionment empirical data and land use information were also collected. Since previous MST studies have been based on laboratory trials using 'manufactured' samples or analyses of spot environmental samples without the contextual microbial flux data (under high and low flow conditions) and source information, such background data are needed to evaluate the utility of MST in USCWA total maximum daily load (TMDL) assessments or WFD 'Programmes of Measures'. Thus, the operational utility of MST remains in some doubt. The results of this investigation, using genotyping of Bacteroidetes using polymerase chain reaction (PCR) and male-specific ribonucleic acid coliphage (F + RNA coliphage) using hybridisation, suggest some discrimination is possible between livestock- and human-derived faecal indicator concentrations but, in inter-grade areas, the degree to which the tracer picture reflected the land use pattern and probable faecal indicator loading were less distinct. Interestingly, the MST data was more reliable on high flow samples when much of the faecal indicator flux from catchment systems occurs. Whilst a useful supplementary tool, the MST information did not provide quantitative source apportionment for the study catchment. Thus, it could not replace detailed empirical measurement of microbial flux at key catchment outlets to underpin faecal indicator source apportionment. Therefore, the MST techniques reported herein currently may not meet the standards required to be a useful forensic tool, although continued development of the methods and further catchment scale studies could increase confidence in such methods for future application.

Implementation and evaluation of PM2.5 source contribution analysis in a photochemical model

EPA Science Inventory

Source culpability assessments are useful for developing effective emissions control programs. The Integrated Source Apportionment Method (ISAM) has been implemented in the Community Multiscale Air Quality (CMAQ) model to track contributions from source groups and regions to ambi...

Source Region Identification Using Kernel Smoothing

EPA Science Inventory

As described in this paper, Nonparametric Wind Regression is a source-to-receptor source apportionment model that can be used to identify and quantify the impact of possible source regions of pollutants as defined by wind direction sectors. It is described in detail with an exam...

ACTRIS ACSM intercomparison - Part 2: Intercomparison of ME-2 organic source apportionment results from 15 individual, co-located aerosol mass spectrometers

NASA Astrophysics Data System (ADS)

Fröhlich, R.; Crenn, V.; Setyan, A.; Belis, C. A.; Canonaco, F.; Favez, O.; Riffault, V.; Slowik, J. G.; Aas, W.; Aijälä, M.; Alastuey, A.; Artiñano, B.; Bonnaire, N.; Bozzetti, C.; Bressi, M.; Carbone, C.; Coz, E.; Croteau, P. L.; Cubison, M. J.; Esser-Gietl, J. K.; Green, D. C.; Gros, V.; Heikkinen, L.; Herrmann, H.; Jayne, J. T.; Lunder, C. R.; Minguillón, M. C.; Močnik, G.; O'Dowd, C. D.; Ovadnevaite, J.; Petralia, E.; Poulain, L.; Priestman, M.; Ripoll, A.; Sarda-Estève, R.; Wiedensohler, A.; Baltensperger, U.; Sciare, J.; Prévôt, A. S. H.

2015-06-01

Chemically resolved atmospheric aerosol data sets from the largest intercomparison of the Aerodyne aerosol chemical speciation monitors (ACSMs) performed to date were collected at the French atmospheric supersite SIRTA. In total 13 quadrupole ACSMs (Q-ACSM) from the European ACTRIS ACSM network, one time-of-flight ACSM (ToF-ACSM), and one high-resolution ToF aerosol mass spectrometer (AMS) were operated in parallel for about 3 weeks in November and December~2013. Part 1 of this study reports on the accuracy and precision of the instruments for all the measured species. In this work we report on the intercomparison of organic components and the results from factor analysis source apportionment by positive matrix factorisation (PMF) utilising the multilinear engine 2 (ME-2). Except for the organic contribution of mass-to-charge ratio m/z 44 to the total organics (f44), which varied by factors between 0.6 and 1.3 compared to the mean, the peaks in the organic mass spectra were similar among instruments. The m/z 44 differences in the spectra resulted in a variable f44 in the source profiles extracted by ME-2, but had only a minor influence on the extracted mass contributions of the sources. The presented source apportionment yielded four factors for all 15 instruments: hydrocarbon-like organic aerosol (HOA), cooking-related organic aerosol (COA), biomass burning-related organic aerosol (BBOA) and secondary oxygenated organic aerosol (OOA). ME-2 boundary conditions (profile constraints) were optimised individually by means of correlation to external data in order to achieve equivalent / comparable solutions for all ACSM instruments and the results are discussed together with the investigation of the influence of alternative anchors (reference profiles). A comparison of the ME-2 source apportionment output of all 15 instruments resulted in relative standard deviations (SD) from the mean between 13.7 and 22.7 % of the source's average mass contribution depending on the factors (HOA: 14.3 ± 2.2 %, COA: 15.0 ± 3.4 %, OOA: 41.5 ± 5.7 %, BBOA: 29.3 ± 5.0 %). Factors which tend to be subject to minor factor mixing (in this case COA) have higher relative uncertainties than factors which are recognised more readily like the OOA. Averaged over all factors and instruments the relative first SD from the mean of a source extracted with ME-2 was 17.2 %.

Ft. McHenry tunnel study: Source profiles and mercury emissions from diesel and gasoline powered vehicles

NASA Astrophysics Data System (ADS)

Landis, Matthew S.; Lewis, Charles W.; Stevens, Robert K.; Keeler, Gerald J.; Dvonch, J. Timothy; Tremblay, Raphael T.

During the fall of 1998, the US Environmental Protection Agency and the Florida Department of Environmental Protection sponsored a 7-day study at the Ft. McHenry tunnel in Baltimore, MD with the objective of obtaining PM 2.5 vehicle source profiles for use in atmospheric mercury source apportionment studies. PM 2.5 emission profiles from gasoline and diesel powered vehicles were developed from analysis of trace elements, polycyclic aromatic hydrocarbons (PAH), and condensed aliphatic hydrocarbons. PM 2.5 samples were collected using commercially available sampling systems and were extracted and analyzed using conventional well-established methods. Both inorganic and organic profiles were sufficiently unique to mathematically discriminate the contributions from each source type using a chemical mass balance source apportionment approach. However, only the organic source profiles provided unique PAH tracers (e.g., fluoranthene, pyrene, and chrysene) for diesel combustion that could be used to identify source contributions generated using multivariate statistical receptor modeling approaches. In addition, the study found significant emission of gaseous elemental mercury (Hg 0), divalent reactive gaseous mercury (RGM), and particulate mercury (Hg(p)) from gasoline but not from diesel powered motor vehicles. Fuel analysis supported the tunnel measurement results showing that total mercury content in all grades of gasoline (284±108 ng L -1) was substantially higher than total mercury content in diesel fuel (62±37 ng L -1) collected contemporaneously at local Baltimore retailers.

Seasonal and Spatial Variability of Anthropogenic and Natural Factors Influencing Groundwater Quality Based on Source Apportionment

PubMed Central

Guo, Xueru; Zuo, Rui; Meng, Li; Wang, Jinsheng; Teng, Yanguo; Liu, Xin; Chen, Minhua

2018-01-01

Globally, groundwater resources are being deteriorated by rapid social development. Thus, there is an urgent need to assess the combined impacts of natural and enhanced anthropogenic sources on groundwater chemistry. The aim of this study was to identify seasonal characteristics and spatial variations in anthropogenic and natural effects, to improve the understanding of major hydrogeochemical processes based on source apportionment. 34 groundwater points located in a riverside groundwater resource area in northeast China were sampled during the wet and dry seasons in 2015. Using principal component analysis and factor analysis, 4 principal components (PCs) were extracted from 16 groundwater parameters. Three of the PCs were water-rock interaction (PC1), geogenic Fe and Mn (PC2), and agricultural pollution (PC3). A remarkable difference (PC4) was organic pollution originating from negative anthropogenic effects during the wet season, and geogenic F enrichment during the dry season. Groundwater exploitation resulted in dramatic depression cone with higher hydraulic gradient around the water source area. It not only intensified dissolution of calcite, dolomite, gypsum, Fe, Mn and fluorine minerals, but also induced more surface water recharge for the water source area. The spatial distribution of the PCs also suggested the center of the study area was extremely vulnerable to contamination by Fe, Mn, COD, and F−. PMID:29415516

Chemical mass balance source apportionment of TSP in a lignite-burning area of Western Macedonia, Greece

NASA Astrophysics Data System (ADS)

Samara, Constantini

Total suspended particle mass concentrations (TSP) were determined in the Kozani-Ptolemais-Florina basin (western Macedonia, Greece), an area with intensive lignite burning for power generation. The study was conducted over a 1-year period (November 2000-November 2001) at 10 receptor sites located at variable distances from the power plants. Ambient TSP samples were analyzed for 27 major, minor and trace elements. Particulate emissions were also collected from a variety of sources including fly ash, lignite dust, automobile traffic, domestic heating, and open-air burning of agricultural biomass and refuse, and analyzed for the same chemical components. Ambient and source chemical profiles were used for source identification and apportionment of TSP by employing a chemical mass balance (CMB) receptor model. Diesel burning in vehicular traffic and in the power plants for generator start up was found to be the major contributor to ambient TSP levels at all 10 sites. Other sources with significant contributions were domestic coal burning, vegetative burning (wood combustion and agricultural burns) and refuse open-air burning. Fly ash escaping the electrostatic precipitators of the power plants was a minor contributor to ambient TSP.

Non-domestic phosphorus release in rivers during low-flow: Mechanisms and implications for sources identification

NASA Astrophysics Data System (ADS)

Dupas, Rémi; Tittel, Jörg; Jordan, Phil; Musolff, Andreas; Rode, Michael

2018-05-01

A common assumption in phosphorus (P) load apportionment studies is that P loads in rivers consist of flow independent point source emissions (mainly from domestic and industrial origins) and flow dependent diffuse source emissions (mainly from agricultural origin). Hence, rivers dominated by point sources will exhibit highest P concentration during low-flow, when flow dilution capacity is minimal, whereas rivers dominated by diffuse sources will exhibit highest P concentration during high-flow, when land-to-river hydrological connectivity is maximal. Here, we show that Soluble Reactive P (SRP) concentrations in three forested catchments free of point sources exhibited seasonal maxima during the summer low-flow period, i.e. a pattern expected in point source dominated areas. A load apportionment model (LAM) is used to show how point sources contribution may have been overestimated in previous studies, because of a biogeochemical process mimicking a point source signal. Almost twenty-two years (March 1995-September 2016) of monthly monitoring data of SRP, dissolved iron (Fe) and nitrate-N (NO3) were used to investigate the underlying mechanisms: SRP and Fe exhibited similar seasonal patterns and opposite to that of NO3. We hypothesise that Fe oxyhydroxide reductive dissolution might be the cause of SRP release during the summer period, and that NO3 might act as a redox buffer, controlling the seasonality of SRP release. We conclude that LAMs may overestimate the contribution of P point sources, especially during the summer low-flow period, when eutrophication risk is maximal.

Identifying PM2.5 and PM0.1 sources for epidemiological studies in California.

PubMed

Hu, Jianlin; Zhang, Hongliang; Chen, Shuhua; Ying, Qi; Wiedinmyer, Christine; Vandenberghe, Francois; Kleeman, Michael J

2014-05-06

The University of California-Davis_Primary (UCD_P) model was applied to simultaneously track ∼ 900 source contributions to primary particulate matter (PM) in California for seven continuous years (January 1st, 2000 to December 31st, 2006). Predicted source contributions to primary PM2.5 mass, PM1.8 elemental carbon (EC), PM1.8 organic carbon (OC), PM0.1 EC, and PM0.1 OC were in general agreement with the results from previous source apportionment studies using receptor-based techniques. All sources were further subjected to a constraint check based on model performance for PM trace elemental composition. A total of 151 PM2.5 sources and 71 PM0.1 sources contained PM elements that were predicted at concentrations in general agreement with measured values at nearby monitoring sites. Significant spatial heterogeneity was predicted among the 151 PM2.5 and 71 PM0.1 source concentrations, and significantly different seasonal profiles were predicted for PM2.5 and PM0.1 in central California vs southern California. Population-weighted concentrations of PM emitted from various sources calculated using the UCD_P model spatial information differed from the central monitor estimates by up to 77% for primary PM2.5 mass and 148% for PM2.5 EC because the central monitor concentration is not representative of exposure for nearby population. The results from the UCD_P model provide enhanced source apportionment information for epidemiological studies to examine the relationship between health effects and concentrations of primary PM from individual sources.

O3 Source Contribution During a Heavy O3 Pollution Episode in Shanghai China

EPA Science Inventory

Source culpability assessments are useful for developing effective emission control strategies. The Integrated Source Apportionment Method (ISAM) has been implemented in CMAQ to track contributions from source groups and regions to ambient levels and deposited amounts of O3. CMAQ...

Primary sources of PM2.5 organic aerosol in an industrial Mediterranean city, Marseille

NASA Astrophysics Data System (ADS)

El Haddad, I.; Marchand, N.; Wortham, H.; Piot, C.; Besombes, J.-L.; Cozic, J.; Chauvel, C.; Armengaud, A.; Robin, D.; Jaffrezo, J.-L.

2011-03-01

Marseille, the most important port of the Mediterranean Sea, represents a challenging case study for source apportionment exercises, combining an active photochemistry and multiple emission sources, including fugitive emissions from industrial sources and shipping. This paper presents a Chemical Mass Balance (CMB) approach based on organic markers and metals to apportion the primary sources of organic aerosol in Marseille, with a special focus on industrial emissions. Overall, the CMB model accounts for the major primary anthropogenic sources including motor vehicles, biomass burning and the aggregate emissions from three industrial processes (heavy fuel oil combustion/shipping, coke production and steel manufacturing) as well as some primary biogenic emissions. This source apportionment exercise is well corroborated by 14C measurements. Primary OC estimated by the CMB accounts on average for 22% of total OC and is dominated by the vehicular emissions that contribute on average for 17% of OC mass concentration (vehicular PM contributes for 17% of PM2.5). Even though industrial emissions contribute only 2.3% of the total OC (7% of PM2.5), they are associated with ultrafine particles (Dp<80 nm) and high concentrations of Polycyclic Aromatic Hydrocarbons (PAH) and heavy metals such as Pb, Ni and V. On one hand, given that industrial emissions governed key primary markers, their omission would lead to substantial uncertainties in the CMB analysis performed in areas heavily impacted by such sources, hindering accurate estimation of non-industrial primary sources and secondary sources. On the other hand, being associated with bursts of submicron particles and carcinogenic and mutagenic components such as PAH, these emissions are most likely related with acute ill-health outcomes and should be regulated despite their small contributions to OC. Another important result is the fact that 78% of OC mass cannot be attributed to the major primary sources and, thus, remains un-apportioned. We have consequently critically investigated the uncertainties underlying our CMB apportionments. While we have provided some evidence for photochemical decay of hopanes, this decay does not appear to significantly alter the CMB estimates of the total primary OC. Sampling artifacts and unaccounted primary sources also appear to marginally influence the amount of un-apportioned OC. Therefore, this significant amount of un-apportioned OC is mostly attributed to secondary organic carbon that appears to be the major component of OC during the whole period of study.

Positive matrix factorization of PM2.5 - eliminating the effects of gas/particle partitioning of semivolatile organic compounds.

PubMed

Xie, M; Barsanti, K C; Hannigan, M P; Dutton, S J; Vedal, S

2013-01-01

Gas-phase concentrations of semi-volatile organic compounds (SVOCs) were calculated from gas/particle (G/P) partitioning theory using their measured particle-phase concentrations. The particle-phase data were obtained from an existing filter measurement campaign (27 January 2003-2 October 2005) as a part of the Denver Aerosol Sources and Health (DASH) study, including 970 observations of 71 SVOCs (Xie et al., 2013). In each compound class of SVOCs, the lighter species (e.g. docosane in n alkanes, fluoranthene in PAHs) had higher total concentrations (gas + particle phase) and lower particle-phase fractions. The total SVOC concentrations were analyzed using positive matrix factorization (PMF). Then the results were compared with source apportionment results where only particle-phase SVOC concentrations were used (particle only-based study; Xie et al., 2013). For the particle only-based PMF analysis, the factors primarily associated with primary or secondary sources ( n alkane, EC/sterane and inorganic ion factors) exhibit similar contribution time series ( r = 0.92-0.98) with their corresponding factors ( n alkane, sterane and nitrate+sulfate factors) in the current work. Three other factors (light n alkane/PAH, PAH and summer/odd n alkane factors) are linked with pollution sources influenced by atmospheric processes (e.g. G/P partitioning, photochemical reaction), and were less correlated ( r = 0.69-0.84) with their corresponding factors (light SVOC, PAH and bulk carbon factors) in the current work, suggesting that the source apportionment results derived from particle-only SVOC data could be affected by atmospheric processes. PMF analysis was also performed on three temperature-stratified subsets of the total SVOC data, representing ambient sampling during cold (daily average temperature < 10 °C), warm (≥ 10 °C and ≤ 20 °C) and hot (> 20 °C) periods. Unlike the particle only-based study, in this work the factor characterized by the low molecular weight (MW) compounds (light SVOC factor) exhibited strong correlations ( r = 0.82-0.98) between the full data set and each sub-data set solution, indicating that the impacts of G/P partitioning on receptor-based source apportionment could be eliminated by using total SVOC concentrations.

Identification of biased sectors in emission data using a combination of chemical transport model and receptor model

NASA Astrophysics Data System (ADS)

Uranishi, Katsushige; Ikemori, Fumikazu; Nakatsubo, Ryohei; Shimadera, Hikari; Kondo, Akira; Kikutani, Yuki; Asano, Katsuyoshi; Sugata, Seiji

2017-10-01

This study presented a comparison approach with multiple source apportionment methods to identify which sectors of emission data have large biases. The source apportionment methods for the comparison approach included both receptor and chemical transport models, which are widely used to quantify the impacts of emission sources on fine particulate matter of less than 2.5 μm in diameter (PM2.5). We used daily chemical component concentration data in the year 2013, including data for water-soluble ions, elements, and carbonaceous species of PM2.5 at 11 sites in the Kinki-Tokai district in Japan in order to apply the Positive Matrix Factorization (PMF) model for the source apportionment. Seven PMF factors of PM2.5 were identified with the temporal and spatial variation patterns and also retained features of the sites. These factors comprised two types of secondary sulfate, road transportation, heavy oil combustion by ships, biomass burning, secondary nitrate, and soil and industrial dust, accounting for 46%, 17%, 7%, 14%, 13%, and 3% of the PM2.5, respectively. The multiple-site data enabled a comprehensive identification of the PM2.5 sources. For the same period, source contributions were estimated by air quality simulations using the Community Multiscale Air Quality model (CMAQ) with the brute-force method (BFM) for four source categories. Both models provided consistent results for the following three of the four source categories: secondary sulfates, road transportation, and heavy oil combustion sources. For these three target categories, the models' agreement was supported by the small differences and high correlations between the CMAQ/BFM- and PMF-estimated source contributions to the concentrations of PM2.5, SO42-, and EC. In contrast, contributions of the biomass burning sources apportioned by CMAQ/BFM were much lower than and little correlated with those captured by the PMF model, indicating large uncertainties in the biomass burning emissions used in the CMAQ simulations. Thus, this comparison approach using the two antithetical models enables us to identify which sectors of emission data have large biases for improvement of future air quality simulations.

Investigating the contribution of shipping emissions to atmospheric PM2.5 using a combined source apportionment approach.

PubMed

Lang, Jianlei; Zhou, Ying; Chen, Dongsheng; Xing, Xiaofan; Wei, Lin; Wang, Xiaotong; Zhao, Na; Zhang, Yanyun; Guo, Xiurui; Han, Lihui; Cheng, Shuiyuan

2017-10-01

Many studies have been conducted focusing on the contribution of land emission sources to PM 2.5 in China; however, little attention had been paid to other contributions, especially the secondary contributions from shipping emissions to atmospheric PM 2.5 . In this study, a combined source apportionment approach, including principle component analysis (PCA) and WRF-CMAQ simulation, was applied to identify both primary and secondary contributions from ships to atmospheric PM 2.5 . An intensive PM 2.5 observation was conducted from April 2014 to January 2015 in Qinhuangdao, which was close to the largest energy output port of China. The chemical components analysis results showed that the primary component was the major contributor to PM 2.5 , with proportions of 48.3%, 48.9%, 55.1% and 55.4% in spring, summer, autumn and winter, respectively. The secondary component contributed higher fractions in summer (48.2%) and winter (36.8%), but had lower percentages in spring (30.1%) and autumn (32.7%). The hybrid source apportionment results indicated that the secondary contribution (SC) of shipping emissions to PM 2.5 could not be ignored. The annual average SC was 2.7%, which was comparable to the primary contribution (2.9%). The SC was higher in summer (5.3%), but lower in winter (1.1%). The primary contributions to atmospheric PM 2.5 were 3.0%, 2.5%, 3.4% and 2.7% in spring, summer, autumn and winter, respectively. As for the detailed chemical components, the contributions of shipping emissions were 2.3%, 0.5%, 0.1%, 1.0%, 1.7% and 0.1% to elements & sea salt, primary organic aerosol (POA), element carbon (EC), nitrate, sulfate and secondary organic carbon (SOA), respectively. The results of this study will further the understanding of the implications of shipping emissions in PM 2.5 pollution. Copyright © 2017 Elsevier Ltd. All rights reserved.

SPECIATE--EPA'S DATABASE OF SPECIATED EMISSION PROFILES

EPA Science Inventory

SPECIATE is EPA's repository of Total Organic Compound and Particulate Matter speciated profiles for a wide variety of sources. The profiles in this system are provided for air quality dispersion modeling and as a library for source-receptor and source apportionment type models. ...

"OZONE SOURCE APPORTIONMENT IN CMAQ'

EPA Science Inventory

Ozone source attribution has been used to support various policy purposes including interstate transport (Cross State Air Pollution Rule) by U.S. EPA and ozone nonattainment area designations by State agencies. Common scientific applications include tracking intercontinental tran...

ORGANIC MOLECULAR MARKER ANALYSIS OF LOW VOLUME RESIDENTIAL SAMPLES FOR SOURCE APPORTIONMENT IN THE DETROIT EXPOSURE AND AEROSOL RESEARCH STUDY

EPA Science Inventory

This abstract describes a poster on results for organic speciation analysis for Detroit Exposure and Aerosol Research Study (DEARS) to be presented at the 2006 International Aerosol Conference sponsored by the American Association for Aerosol Research in St. Paul, Minnesota on Se...

Assessing the Anthropogenic Fugitive Dust Emission Inventory and Temporal Allocation Using an Updated Speciation of Particulate Matter

EPA Science Inventory

Crustal materials are mainly emitted by anthropogenic and windblown fugitive dust, but also may potentially include some fly ash and industrial process emissions which are chemically similar to crustal emissions. Source apportionment studies have shown that anthropogenic fugitive...

Source apportionment of settleable particles in an impacted urban and industrialized region in Brazil.

PubMed

Santos, Jane Meri; Reis, Neyval Costa; Galvão, Elson Silva; Silveira, Alexsander; Goulart, Elisa Valentim; Lima, Ana Teresa

2017-09-01

Settleable particulate matter (SPM), especially coarser particles with diameters greater than 10 μm, has been found culprit of high deposition rates in cities affected by hinterland industrial activities. This is the case of Metropolitan Region of Vitoria (MRV), Espirito Santo, Brazil where industrial facilities are located within the urban sprawl and building constructions are intense. Frequent population complaints to the environmental protection agency (IEMA) throughout the years have triggered monitoring campaigns to determine SPM deposition rates and source apportionment. Eight different locations were monitored throughout the MRV, and SPM was quantified and chemically characterized. Sources profiles were defined either by using US EPA SPECIATE data or by experimental analysis. Atmospheric fallout in the MRV ranged between 2 and 20g/(m 2 30-day), with only one monitoring station ranging from 6-10 g/(m 2 30-day). EC, OC, Fe, Al, and Si were found the main constituents of dry deposition in the region. Source apportionment by the chemical mass balance (CMB) model determined that steel and iron ore pelletizing industries were the main contributor to one of the eight locations whereas resuspension, civil construction, and vehicular sources were also very important contributors to the other stations. Quarries and soil were also considered expressive SPM sources, but at the city periphery. CMB model could differentiate contributions from six industrial source groups: thermoelectric; iron ore, pellet, and pellet furnaces; coal coke and coke oven; sintering, blast furnace, and basic oxygen furnace; and soil, resuspension, and vehicles. However, the CMB model was unable to differentiate between iron ore and pellet stockpiles which are present in both steel and iron ore pelletizing industries. Further characterization of source and SPM might be necessary to aid local authorities in decision-making regarding these two industrial sources.

SOURCE APPORTIONMENT OF PHOENIX PM2.5 AEROSOL WITH THE UNMIX RECEPTOR MODEL

EPA Science Inventory

The multivariate receptor model Unmix has been used to analyze a 3-yr PM2.5 ambient aerosol data set collected in Phoenix, AZ, beginning in 1995. The analysis generated source profiles and overall percentage source contribution estimates (SCE) for five source categories: ga...

Trace elements and common ions in southeastern Idaho snow: Regional air pollutant tracers for source area emissions

USGS Publications Warehouse

Abbott, M.; Einerson, J.; Schuster, P.; Susong, D.; Taylor, Howard E.; ,

2004-01-01

Snow sampling and analysis methods which produce accurate and ultra-low measurements of trace elements and common ion concentration in southeastern Idaho snow, were developed. Snow samples were collected over two winters to assess trace elements and common ion concentrations in air pollutant fallout across the southeastern Idaho. The area apportionment of apportionment of fallout concentrations measured at downwind location were investigated using pattern recognition and multivariate statistical technical techniques. Results show a high level of contribution from phosphates processing facilities located outside Pocatello in the southern portion of the Eastern Snake River Plain, and no obvious source area profiles other than at Pocatello.

RECEPTOR MODEL DEVELOPMENT AND APPLICATION

EPA Science Inventory

Source apportionment (receptor) models are mathematical procedures for identifying and quantifying the sources of ambient air pollutants and their effects at a site (the receptor), primarily on the basis of species concentration measurements at the receptor, and generally without...

Source apportionment of trace metals in surface waters of a polluted stream using multivariate statistical analyses.

PubMed

Pekey, Hakan; Karakaş, Duran; Bakoğlu, Mithat

2004-11-01

Surface water samples were collected from ten previously selected sites of the polluted Dil Deresi stream, during two field surveys, December 2001 and April 2002. All samples were analyzed using ICP-AES, and the concentrations of trace metals (Al, As, Ba, Cd, Co, Cr, Cu, Fe, Pb, Sn and Zn) were determined. The results were compared with national and international water quality guidelines, as well as literature values reported for similar rivers. Factor analysis (FA) and a factor analysis-multiple regression (FA-MR) model were used for source apportionment and estimation of contributions from identified sources to the concentration of each parameter. By a varimax rotated factor analysis, four source types were identified as the paint industry; sewage, crustal and road traffic runoff for trace metals, explaining about 83% of the total variance. FA-MR results showed that predicted concentrations were calculated with uncertainties lower than 15%.

Source apportionment of formaldehyde during TexAQS 2006 using a source-oriented chemical transport model

NASA Astrophysics Data System (ADS)

Zhang, Hongliang; Li, Jingyi; Ying, Qi; Guven, Birnur Buzcu; Olaguer, Eduardo P.

2013-02-01

In this study, a source-oriented version of the Community Multiscale Air Quality (CMAQ) model was developed and used to quantify the contributions of five major local emission source types in Southeast Texas (vehicles, industry, natural gas combustion, wildfires, biogenic sources), as well as upwind sources, to regional primary and secondary formaldehyde (HCHO) concentrations. Predicted HCHO concentrations agree well with observations at two urban sites (the Moody Tower [MT] site at the University of Houston and the Haden Road #3 [HRM-3] site operated by Texas Commission on Environmental Quality). However, the model underestimates concentrations at an industrial site (Lynchburg Ferry). Throughout most of Southeast Texas, primary HCHO accounts for approximately 20-30% of total HCHO, while the remaining portion is due to secondary HCHO (30-50%) and upwind sources (20-50%). Biogenic sources, natural gas combustion, and vehicles are important sources of primary HCHO in the urban Houston area, respectively, accounting for 10-20%, 10-30%, and 20-60% of total primary HCHO. Biogenic sources, industry, and vehicles are the top three sources of secondary HCHO, respectively, accounting for 30-50%, 10-30%, and 5-15% of overall secondary HCHO. It was also found that over 70% of PAN in the Houston area is due to upwind sources, and only 30% is formed locally. The model-predicted source contributions to HCHO at the MT generally agree with source apportionment results obtained from the Positive Matrix Factorization (PMF) technique.

& Source apportionment of particulate matter in the United States and associations with lung inflammatory Markers

EPA Science Inventory

Size-fractionated particulate matter (PM) samples were collected from six U.S. cities and chemically analyzed as part of the Multiple Air Pollutant Study. Particles were administered to cultured lung cells and the production of three different proinflammatory markers was measured...

Isotope source apportionment of carbonaceous aerosol as a function of particle size and thermal refractiveness

NASA Astrophysics Data System (ADS)

Masalaite, Agne; Holzinger, Rupert; Remeikis, Vidmantas; Röckmann, Thomas; Dusek, Ulrike

2016-04-01

The stable carbon isotopes can be used to get information about sources and processing of carbonaceous aerosol. We will present results from source apportionment of carbonaceous aerosol as a function of particle size thermal refractiveness. Separate source apportionment for particles smaller than 200 nm and for different carbon volatility classes are rarely reported and give new insights into aerosol sources in the urban environment. Stable carbon isotope ratios were measured for the organic carbon (OC) fraction and total carbon (TC) of MOUDI impactor samples that were collected on a coastal site (Lithuania) during the winter 2012 and in the city of Vilnius (Lithuania) during the winter of 2009. The 11 impactor stages spanned a size range from 0.056 to 18 μm, but only the 6 stages in the submicron range were analysed. The δ13C values of bulk total carbon (δ13CTC) were determined with an elemental analyser (Flash EA 1112) coupled with an isotope ratio mass spectrometer (Thermo Finnigan Delta Plus Advantage) (EA - IRMS). Meanwhile δ13COC was measured using thermal-desorption isotope ratio mass spectrometry (IRMS) system. This allows a rough separation of the more volatile OC fraction (desorbed in the oven of IRMS up to 250 0C) from the more refractory fraction (desorbed up to 400 0C). In this study we investigated the composition of organic aerosol desorbed from filter samples at different temperatures using the thermal-desorption proton-transfer-reaction mass spectrometry (TD-PTR-MS) technique. During winter-time in Lithuania we expect photochemistry and biogenic emissions to be of minor importance. The main sources of aerosol carbon should be fossil fuel and biomass combustion. In both sites, the coastal and the urban site, δ13C measurements give a clear indication that the source contributions differ for small and large particles. Small particles < 200 nm are depleted in 13C with respect to larger particles by 1 - 2 ‰Ṫhis shows that OC in small particle arises mainly from fossil fuel sources, whereas OC in larger particles from 200 nm to 1 μm has higher contribution from biomass burning/other sources. Moreover, there is a clear distinction in source contribution between the more volatile OC fraction and the more refractory fraction. The more refractory fraction is enriched in 13C by 1 to 2 ‰ for both small and large particles. These results show that the fossil fuel combustion is associated to a larger degree with more volatile carbon, whereas biomass burning is the main source of the more refractory particles. According to our source apportionment, the more volatile carbon fraction in the smallest particles is almost completely from fossil fuels, whereas the more refractory carbon fraction in the large size range is almost complete from biomass burning. The more refractory small particles and the less refractory large particles are roughly an even mix of these two sources. The detailed chemical speciation of the carbonaceous aerosol will be presented as well. Acknowledgements This study was funded by the Dutch Science Foundation (NWO grants Nr. 820.01.001, and 834.08.002).

Using Source Apportionment to Evaluate the Cross State Transport of Ozone in the Eastern United States

NASA Astrophysics Data System (ADS)

Goldberg, D. L.; Canty, T. P.; Hembeck, L.; Vinciguerra, T.; Carpenter, S. F.; Anderson, D. C.; Salawitch, R. J.; Dickerson, R. R.

2014-12-01

The amount of air pollution crossing state lines has great policy implications. Using the ozone source apportionment tool (OSAT) in the Comprehensive Air-Quality Model with Extensions (CAMx) version 6.10, we can quantify how much ozone is generated locally versus transported from upwind locations. Initial results show that up to 70% of the surface ozone in Maryland during poor air quality days in the summer of July 2011 can be attributed to pollution from outside of the state's borders. Modifications to the CB05 gas-phase chemistry mechanism, supported by literature recommendations and improve agreement with NASA's DISCOVER-AQ Maryland aircraft campaign, can further increase this percentage. Additionally, we show the role of upwind sources and background ozone has become increasingly important as local emissions of ozone precursors continue to drop, starting with the steep reductions imposed in 2002 in response to Maryland's State Implementation Plan submitted to EPA. This study suggests future efforts to control surface ozone must include a meaningful strategy for dealing with cross-state transport of ozone precursors.

Contamination characteristics and source apportionment of heavy metals in topsoil from an area in Xi'an city, China.

PubMed

Chen, Xiuduan; Lu, Xinwei

2018-04-30

As soil-extractable elements potentially pose ecological and health risks, identifying their contamination characteristics and sources is crucial. Therefore, to understand topsoil trace elements in the urban ring zone from the Second Ring Road to the Third Ring of Xi'an city in China, we determined the concentrations of Zn, Co, V, As, Cu, Mn, Ba, Ni and Pb, and analyzed the sources of the contamination. The results showed that the individual pollution indices of Pb, Co, Cu, Zn, Ba, Ni, Mn, As, and V were 1.79, 1.48, 1.41, 1.33, 1.20, 1.07, 1.04, 0.99, and 0.99, respectively. Evaluation with the aid of the pollution load index (PLI) indicated slight soil contamination by these elements in the study area. Using the positive matrix factorization (PMF) method, we identified four sources of contamination, namely (1) a natural source, (2) traffic emission source, (3) industrial emission source, and (4) mixed source. PMF is an effective tool for source apportionment of heavy metals in topsoil. The contribution rates of the natural source, traffic source, mixed source, and industrial source to the heavy metal contamination were specified as 25.04%, 24.71%, 24.99%, and 25.26%, respectively. Considering the above, any attempt to reduce the soil environmental cost of urban development, has to take into account the heavy metal contamination of the topsoil from industries, traffic, and other activities. Copyright © 2018 Elsevier Inc. All rights reserved.

Chemical Composition and Source Apportionment of Size Fractionated Particulate Matter in Cleveland, Ohio, USA

EPA Science Inventory

The Cleveland airshed comprises a complex mixture of industrial source emissions that contribute to periods of non-attainment for fine particulate matter (PM 2.5 ) and are associated with increased adverse health outcomes in the exposed population. Specific PM sources responsible...

Reconciling PM10 analyses by different sampling methods for Iron King Mine tailings dust.

PubMed

Li, Xu; Félix, Omar I; Gonzales, Patricia; Sáez, Avelino Eduardo; Ela, Wendell P

2016-03-01

The overall project objective at the Iron King Mine Superfund site is to determine the level and potential risk associated with heavy metal exposure of the proximate population emanating from the site's tailings pile. To provide sufficient size-fractioned dust for multi-discipline research studies, a dust generator was built and is now being used to generate size-fractioned dust samples for toxicity investigations using in vitro cell culture and animal exposure experiments as well as studies on geochemical characterization and bioassay solubilization with simulated lung and gastric fluid extractants. The objective of this study is to provide a robust method for source identification by comparing the tailing sample produced by dust generator and that collected by MOUDI sampler. As and Pb concentrations of the PM10 fraction in the MOUDI sample were much lower than in tailing samples produced by the dust generator, indicating a dilution of Iron King tailing dust by dust from other sources. For source apportionment purposes, single element concentration method was used based on the assumption that the PM10 fraction comes from a background source plus the Iron King tailing source. The method's conclusion that nearly all arsenic and lead in the PM10 dust fraction originated from the tailings substantiates our previous Pb and Sr isotope study conclusion. As and Pb showed a similar mass fraction from Iron King for all sites suggesting that As and Pb have the same major emission source. Further validation of this simple source apportionment method is needed based on other elements and sites.

Heavy metal contamination of surface soil in electronic waste dismantling area: site investigation and source-apportionment analysis.

PubMed

Jinhui Li; Huabo Duan; Pixing Shi

2011-07-01

The dismantling and disposal of electronic waste (e-waste) in developing countries is causing increasing concern because of its impacts on the environment and risks to human health. Heavy-metal concentrations in the surface soils of Guiyu (Guangdong Province, China) were monitored to determine the status of heavy-metal contamination on e-waste dismantling area with a more than 20 years history. Two metalloids and nine metals were selected for investigation. This paper also attempts to compare the data among a variety of e-waste dismantling areas, after reviewing a number of heavy-metal contamination-related studies in such areas in China over the past decade. In addition, source apportionment of heavy metal in the surface soil of these areas has been analysed. Both the MSW open-burning sites probably contained invaluable e-waste and abandoned sites formerly involved in informal recycling activities are the new sources of soil-based environmental pollution in Guiyu. Although printed circuit board waste is thought to be the main source of heavy-metal emissions during e-waste processing, requirement is necessary to soundly manage the plastic separated from e-waste, which mostly contains heavy metals and other toxic substances.

Tim Watkins

EPA Pesticide Factsheets

Tim’s expertise and interests lie in the area of air pollution exposure assessment, including ambient air monitoring, personal monitoring, source apportionment, and air quality and exposure modeling.

Seasonal assessment and apportionment of surface water pollution using multivariate statistical methods: Sinos River, southern Brazil.

PubMed

Alves, Darlan Daniel; Riegel, Roberta Plangg; de Quevedo, Daniela Müller; Osório, Daniela Montanari Migliavacca; da Costa, Gustavo Marques; do Nascimento, Carlos Augusto; Telöken, Franko

2018-06-08

Assessment of surface water quality is an issue of currently high importance, especially in polluted rivers which provide water for treatment and distribution as drinking water, as is the case of the Sinos River, southern Brazil. Multivariate statistical techniques allow a better understanding of the seasonal variations in water quality, as well as the source identification and source apportionment of water pollution. In this study, the multivariate statistical techniques of cluster analysis (CA), principal component analysis (PCA), and positive matrix factorization (PMF) were used, along with the Kruskal-Wallis test and Spearman's correlation analysis in order to interpret a water quality data set resulting from a monitoring program conducted over a period of almost two years (May 2013 to April 2015). The water samples were collected from the raw water inlet of the municipal water treatment plant (WTP) operated by the Water and Sewage Services of Novo Hamburgo (COMUSA). CA allowed the data to be grouped into three periods (autumn and summer (AUT-SUM); winter (WIN); spring (SPR)). Through the PCA, it was possible to identify that the most important parameters in contribution to water quality variations are total coliforms (TCOLI) in SUM-AUT, water level (WL), water temperature (WT), and electrical conductivity (EC) in WIN and color (COLOR) and turbidity (TURB) in SPR. PMF was applied to the complete data set and enabled the source apportionment water pollution through three factors, which are related to anthropogenic sources, such as the discharge of domestic sewage (mostly represented by Escherichia coli (ECOLI)), industrial wastewaters, and agriculture runoff. The results provided by this study demonstrate the contribution provided by the use of integrated statistical techniques in the interpretation and understanding of large data sets of water quality, showing also that this approach can be used as an efficient methodology to optimize indicators for water quality assessment.

Determining the contribution of long-range transport, regional and local source areas, to PM10 mass loading in Hessen, Germany using a novel multi-receptor based statistical approach

NASA Astrophysics Data System (ADS)

Garg, Saryu; Sinha, Baerbel

2017-10-01

This study uses two newly developed statistical source apportionment models, MuSAM and MuReSAM, to perform quantitative statistical source apportionment of PM10 at multiple receptor sites in South Hessen. MuSAM uses multi-site back trajectory data to quantify the contribution of long-range transport, while MuReSAM uses wind speed and direction as proxy for regional transport and quantifies the contribution of regional source areas. On average, between 7.8 and 9.1 μg/m3 of PM10 (∼50%) at receptor sites in South Hessen is contributed by long-range transport. The dominant source regions are Eastern, South Eastern, and Southern Europe. 32% of the PM10 at receptor sites in South Hessen is contributed by regional source areas (2.8-9.41 μg/m3). This fraction varies from <20% at remote sites to >40% for urban stations. Sources located within a 2 km radius around the receptor site are responsible for 7%-20% of the total PM10 mass (0.7-4.4 μg/m3). The perturbation study of the traffic flow due to the closing and reopening of the Schiersteiner Brücke revealed that the contribution of the bridge to PM10 mass loadings at two nearby receptor sites increased by approximately 120% after it reopened and became a bottleneck, although in absolute terms, the increase is small.

Characterization and source apportionment of health risks from ambient PM10 in Hong Kong over 2000-2011

NASA Astrophysics Data System (ADS)

Li, Zhiyuan; Yuan, Zibing; Li, Ying; Lau, Alexis K. H.; Louie, Peter K. K.

2015-12-01

Atmospheric particulate matter (PM) pollution is a major public health concern in Hong Kong. In this study, the spatiotemporal variations of health risks from ambient PM10 from seven air quality monitoring stations between 2000 and 2011 were analyzed. Positive matrix factorization (PMF) was adopted to identify major source categories of ambient PM10 and quantify their contributions. Afterwards, a point-estimated risk model was used to identify the inhalation cancer and non-cancer risks of PM10 sources. The long-term trends of the health risks from classified local and non-local sources were explored. Furthermore, the reason for the increase of health risks during high PM10 days was discussed. Results show that vehicle exhaust source was the dominant inhalation cancer risk (ICR) contributor (72%), whereas trace metals and vehicle exhaust sources contributed approximately 27% and 21% of PM10 inhalation non-cancer risk (INCR), respectively. The identified local sources accounted for approximately 80% of the ICR in Hong Kong, while contribution percentages of the non-local and local sources for INCR are comparable. The clear increase of ICR at high PM days was mainly attributed to the increase of contributions from coal combustion/biomass burning and secondary sulfate, while the increase of INCR at high PM days was attributed to the increase of contributions from the sources coal combustion/biomass burning, secondary nitrate, and trace metals. This study highlights the importance of health risk-based source apportionment in air quality management with protecting human health as the ultimate target.

Source apportionment of VOCs and the contribution to photochemical ozone formation during summer in the typical industrial area in the Yangtze River Delta, China

NASA Astrophysics Data System (ADS)

Shao, Ping; An, Junlin; Xin, Jinyuan; Wu, Fangkun; Wang, Junxiu; Ji, Dongsheng; Wang, Yuesi

2016-07-01

Volatile organic compounds (VOCs) were continuously observated in a northern suburb of Nanjing, a typical industrial area in the Yangtze River Delta, in a summer observation period from 15th May to 31st August 2013. The average concentration of total VOCs was (34.40 ± 25.20) ppbv, including alkanes (14.98 ± 12.72) ppbv, alkenes (7.35 ± 5.93) ppbv, aromatics (9.06 ± 6.64) ppbv and alkynes (3.02 ± 2.01) ppbv, respectively. Source apportionment via Positive Matrix Factorization was conducted, and six major sources of VOCs were identified. The industry-related sources, including industrial emissions and industrial solvent usage, occupied the highest proportion, accounting for about 51.26% of the VOCs. Vehicular emissions occupied the second highest proportion, accounting for about 34.08%. The rest accounted for about 14.66%, including vegetation emission and liquefied petroleum gas/natural gas usage. Contributions of VOCs to photochemical O3 formation were evaluated by the application of a detailed chemical mechanism model (NCAR MM). Alkenes were the dominant contributors to the O3 photochemical production, followed by aromatics and alkanes. Alkynes had a very small impact on photochemical O3 formation. Based on the outcomes of the source apportionment, a sensitivity analysis of relative O3 reduction efficiency (RORE), under different source removal regimes such as using the reduction of VOCs from 10% to 100% as input, was conducted. The RORE was the highest (~ 20%-40%) when the VOCs from solvent-related sources decreased by 40%. The highest RORE values for vegetation emissions, industrial emissions, vehicle exhaust, and LPG/NG usage were presented in the scenarios of 50%, 80%, 40% and 40%, respectively.

Inverse modeling to estimate local source contributions in a complex environment with nearby port, airport, highway, and industrial sources

EPA Science Inventory

Source apportionment is challenging in urban environments with clustered sourceemissions that have similar chemical signatures. A field and inverse modeling studywas conducted in Elizabeth, New Jersey to observe gaseous and particulate pollutionnear the Port of New York and New J...

77 FR 11914 - Approval and Promulgation of Air Quality Implementation Plans; Vermont; Regional Haze

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-28

... United States. Through source apportionment modeling, MANE-VU assisted States in determining their... Contributions of Pollutants to Visibility Impairments 2. Procedure for Identifying Sources To Evaluate for... is visibility impairment that is produced by a multitude of sources and activities which are located...

SOURCE APPORTIONMENT RESULTS, UNCERTAINTIES, AND MODELING TOOLS

EPA Science Inventory

Advanced multivariate receptor modeling tools are available from the U.S. Environmental Protection Agency (EPA) that use only speciated sample data to identify and quantify sources of air pollution. EPA has developed both EPA Unmix and EPA Positive Matrix Factorization (PMF) and ...

A comprehensive analysis of heavy metals in urban road dust of Xi'an, China: Contamination, source apportionment and spatial distribution.

PubMed

Pan, Huiyun; Lu, Xinwei; Lei, Kai

2017-12-31

A detailed investigation was conducted to study heavy metal contamination in road dust from four regions of Xi'an, Northwest China. The concentrations of eight heavy metals Co, Cr, Cu, Mn, Ni, Pb, Zn and V were determined by X-Ray Fluorescence. The mean concentrations of these elements were: 30.9mgkg -1 Co, 145.0mgkg -1 Cr, 54.7mgkg -1 Cu, 510.5mgkg -1 Mn, 30.8mgkg -1 Ni, 124.5mgkg -1 Pb, 69.6mgkg -1 V and 268.6mgkg -1 Zn. There was significant enrichment of Pb, Zn, Co, Cu and Cr based on geo-accumulation index value. Multivariate statistical analysis showed that levels of Cu, Pb, Zn, Co and Cr were controlled by anthropogenic activities, while levels of Mn, Ni and V were associated with natural sources. Principle component analysis and multiple linear regression were applied to determine the source apportionment. The results showed that traffic was the main source with a percent contribution of 53.4%. Natural sources contributed 26.5%, and other anthropogenic pollution sources contributed 20.1%. Clear heavy metal pollution hotspots were identified by GIS mapping. The location of point pollution sources and prevailing wind direction were found to be important factors in the spatial distribution of heavy metals. Copyright © 2017 Elsevier B.V. All rights reserved.

Size-resolved source apportionment of carbonaceous particulate matter in urban and rural sites in central California

NASA Astrophysics Data System (ADS)

Ham, Walter A.; Kleeman, Michael J.

2011-08-01

Very little is currently known about the relationship between exposure to different sources of ambient ultrafine particles (PM 0.1) and human health effects. If human health effects are enhanced by PM 0.1's ability to cross cell membranes, then more information is needed describing the sources of ultrafine particles that are deposited in the human respiratory system. The current study presents results for the source apportionment of airborne particulate matter in six size fractions smaller than 1.8 μm particle diameter including ultrafine particles (PM 0.1) in one of the most polluted air basins in the United States. Size-resolved source apportionment results are presented at an urban site and rural site in central California's heavily polluted San Joaquin Valley during the winter and summer months using a molecular marker chemical mass balance (MM-CMB) method. Respiratory deposition calculations for the size-resolved source apportionment results are carried out with the Multiple Path Particle Dosimetry Model ( MPPD v 2.0), including calculations for ultrafine (PM 0.1) source deposition. Diesel engines accounted for the majority of PM 0.1 and PM 1.8 EC at both the urban and rural sampling locations during both summer and winter seasons. Meat cooking accounted for 33-67% and diesel engines accounted for 15-21% of the PM 0.1 OC at Fresno. Meat cooking accounted for 22-26% of the PM 0.1 OC at the rural Westside location, while diesel engines accounted for 8-9%. Wood burning contributions to PM 0.1 OC increased to as much as 12% of PM 0.1 OC during the wintertime. The modest contribution of wood smoke reflects the success of emissions control programs over the past decade. In contrast to PM 0.1, PM 1.8 OC had a higher fraction of unidentified source contributions (68-85%) suggesting that this material is composed of secondary organic aerosol (SOA) or primary organic aerosol (POA) that has been processed by atmospheric chemical reactions. Meat cooking was the largest identified source of PM 1.8 organic carbon (OC) at the Fresno site (12-13%) while diesel engines were the largest identified PM 1.8 OC source at the rural site (5-8%). Wood burning contributions to PM 1.8 OC increased during the wintertime at both sites (6-9%) but were relatively small during the summertime (˜1%). As expected, diesel engines were the dominant source of PM 0.1 EC respiratory deposition at both the urban and rural site in both summer and winter (0.01-0.03 μg PM 0.1 EC deposited per m 3 air inhaled). Meat cooking accounted for 0.01-0.025 μg PM 0.1 OC deposited per m 3 air inhaled while diesel fuel accounted for 0.005-0.013 μg PM 0.1 OC deposited per m 3 air inhaled. Minor contributions from wood burning, motor oil, and gasoline fuel were calculated at levels <0.005 μg PM 0.1 OC deposited per m 3 air inhaled at both urban and rural locations during winter and summer seasons. If the burden of PM 0.1 deposited in the respiratory system is relevant for human health effects, then future toxicology studies should be carried out at PM 0.1 concentrations and source mixtures equivalent to those measured in the current study.

Characteristics and source apportionment of black carbon aerosols over an urban site.

PubMed

Rajesh, T A; Ramachandran, S

2017-03-01

Aethalometer based source apportionment model using the measured aerosol absorption coefficients at different wavelengths is used to apportion the contribution of fossil fuel and wood burning sources to the total black carbon (BC) mass concentration. Temporal and seasonal variabilities in BC mass concentrations, equivalent BC from fossil fuel (BC f f ), and wood burning (BC w b ) are investigated over an urban location in western India during January 2014 to December 2015. BC, BC f f , and BC w b mass concentrations exhibit strong diurnal variation and are mainly influenced by atmospheric dynamics. BC f f was higher by a factor of 2-4 than BC w b and contributes maximum to BC mass throughout the day, confirming consistent anthropogenic activities. Diurnal contribution of BC f f and BC w b exhibits opposite variation due to differences in emission sources over Ahmedabad. Night time BC values are about a factor of 1.4 higher than day time BC values. The annual mean percentage contributions of day time and night time are 42 and 58 %, respectively. BC, BC f f , and BC w b mass concentrations exhibit large and significant variations during morning, afternoon, evening, and night time. During afternoon, mass concentration values are minimum throughout the year because of the fully evolved boundary layer and reduced anthropogenic activities. BC exhibits a strong seasonal variability with postmonsoon high (8.3 μg m -3 ) and monsoon low (1.9 μg m -3 ). Annual mean BC f f and BC w b contributions are 80 and 20 %, respectively, to total BC, which suggests that major contribution of BC in Ahmedabad comes from fossil fuel emissions. The results show that the study location is dominated by fossil fuel combustion as compared to the emissions from wood burning. The results obtained represent a regional value over an urban regime which can be used as inputs on source apportionment to model BC emissions in regional and global climate models.

Characterization of Aral Sea Particulate Matter in Kyrgyzstan

EPA Science Inventory

1. Elemental analyses of resuspendable soils from the Aral Sea region and Kyrgyz soils show that the composition of the soils are remarkably uniform thereby supporting chemical source apportionment models that treat this region as a homogeneous source with respect to elemental co...

Primary sources of PM2.5 organic aerosol in an industrial Mediterranean city, Marseille

NASA Astrophysics Data System (ADS)

El Haddad, I.; Marchand, N.; Wortham, H.; Piot, C.; Besombes, J.-L.; Cozic, J.; Chauvel, C.; Armengaud, A.; Robin, D.; Jaffrezo, J.-L.

2010-11-01

Marseille, the most important port of the Mediterranean Sea, represents a challenging case study for source apportionment exercises, combining an active photochemistry and multiple emission sources, including fugitive emissions from industrial sources and shipping. This paper presents a Chemical Mass Balance (CMB) approach based on organic markers and metals to apportion the primary sources of organic aerosol in Marseille, with a special focus on industrial emissions. Overall, the CMB model accounts for the major primary anthropogenic sources including motor vehicles, biomass burning, and the aggregate emissions from three industrial processes (HFO combustion/shipping, coke production and steel manufacturing) as well as some primary biogenic emissions. This source apportionment exercise is well corroborated by 14C measurements. Primary OC estimated by the CMB accounts on average for 22% and is dominated by the vehicular emissions that contribute on average for 17% of OC mass concentration (17% of PM2.5). Even though, industrial emissions contribute for only 2.3% of the total OC (7% of PM2.5), they are associated with ultrafine particles (Dp<80 nm) and high concentrations of Polycyclic Aromatic Hydrocarbons (PAH) and heavy metals such as Pb, Ni and V. On one hand, given that industrial emissions governed key primary markers, their omission would lead to substantial uncertainties in the CMB analysis performed in areas heavily impacted by such sources, hindering accurate estimation of non-industrial primary sources and secondary sources. This result implies that CMB modelling should not be a straightforward exercise and one have to carefully investigate the marker behaviours and trends beforehand, especially in complex environments such as Marseille. On the other hand, being associated with bursts of submicron particles and carcinogenic and mutagenic components such as PAH, these emissions are most likely related with acute health outcomes and should be regulated despite their small contributions to OC. Another important result is the fact that 78% of OC mass cannot be attributed to the major primary sources and thus remains un-apportioned. We have consequently critically investigated the uncertainties underlying our CMB apportionments. While we have provided some evidence for photochemical decay of hopanes, this decay does not appear to significantly alter the CMB estimates of the total primary OC. Sampling artefacts and unaccounted primary sources also appear to marginally influence the amount of un-apportioned OC. Therefore, this significant amount of un-apportioned OC is mostly attributed to secondary organic carbon that appears to be the major component of OC, during the whole period of study.

Improved source apportionment of PAHs and Pb by integrating Pb stable isotopes and positive matrix factorization application (PAHs): A historical record case study from the northern South China Sea.

PubMed

Cai, Minggang; Lin, Yan; Chen, Meng; Yang, Weifeng; Du, Huihong; Xu, Ye; Cheng, Shayen; Xu, Fangjian; Hong, Jiajun; Chen, Mian; Ke, Hongwei

2017-12-31

To obtain the historical changes of pyrogenic sources, integrated source apportionment methods, which include PAH compositions, diagnostic ratios (DRs), Pb isotopic ratios, and positive matrix factorization (PMF) model, were developed and applied in sediments of the northern South China Sea. These methods provided a gradually clear picture of energy structural change. Spatially, Σ 15 PAH (11.3 to 95.5ng/g) and Pb (10.2 to 74.6μg/g) generally exhibited decreasing concentration gradient offshore; while the highest levels of PAHs and Pb were observed near the southern Taiwan Strait, which may be induced by accumulation of different fluvial input. Historical records of pollutants followed closely with the economic development of China, with fast growth of Σ 15 PAH and Pb occurring since the 1980s and 1990s, respectively. The phasing-out of leaded gasoline in China was captured with a sharp decrease of Pb after the mid-1990s. PAHs and Pb correlated well with TOC and clay content for core sediments, which was not observed for surface sediments. There was an up-core increase of high molecular PAH proportions. Coal and biomass burning were then qualitatively identified as the major sources of PAHs with DRs. Furthermore, shift toward less radiogenic signatures of Pb isotopic ratios after 1900 revealed the start and growing importance of industrial sources. Finally, a greater separation and quantification of various input was achieved by a three-factor PMF model, which made it clear that biomass burning, coal combustion, and vehicle emissions accounted for 40±20%, 41±13%, and 19±12% of PAHs through the core. Biomass and coal combustion acted as major sources before 2000, while contributions from vehicle emission soared thereafter. The integrated multi-methodologies here improved the source apportionment by reducing biases with a step-down and cross-validation perspective, which could be similarly applied to other aquatic systems. Copyright © 2017 Elsevier B.V. All rights reserved.

Size distribution of chemical elements and their source apportionment in ambient coarse, fine, and ultrafine particles in Shanghai urban summer atmosphere.

PubMed

Lü, Senlin; Zhang, Rui; Yao, Zhenkun; Yi, Fei; Ren, Jingjing; Wu, Minghong; Feng, Man; Wang, Qingyue

2012-01-01

Ambient coarse particles (diameter 1.8-10 microm), fine particles (diameter 0.1-1.8 microm), and ultrafine particles (diameter < 0.1 microm) in the atmosphere of the city of Shanghai were sampled during the summer of 2008 (from Aug 27 to Sep 08). Microscopic characterization of the particles was investigated by scanning electron microscopy coupled with energy dispersive X-ray spectroscopy (SEM/EDX). Mass concentrations of Si, P, S, Cl, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, As, Se, Br, Rb, Sr, and Pb in the size-resolved particles were quantified by using synchrotron radiation X-ray fluorescence (SRXRF). Source apportionment of the chemical elements was analyzed by means of an enrichment factor method. Our results showed that the average mass concentrations of coarse particles, fine particles and ultrafine particles in the summer air were 9.38 +/- 2.18, 8.82 +/- 3.52, and 2.02 +/- 0.41 microg/m3, respectively. The mass percentage of the fine particles accounted for 51.47% in the total mass of PM10, indicating that fine particles are the major component in the Shanghai ambient particles. SEM/EDX results showed that the coarse particles were dominated by minerals, fine particles by soot aggregates and fly ashes, and ultrafine particles by soot particles and unidentified particles. SRXRF results demonstrated that crustal elements were mainly distributed in the coarse particles, while heavy metals were in higher proportions in the fine particles. Source apportionment revealed that Si, K, Ca, Fe, Mn, Rb, and Sr were from crustal sources, and S, Cl, Cu, Zn, As, Se, Br, and Pb from anthropogenic sources. Levels of P, V, Cr, and Ni in particles might be contributed from multi-sources, and need further investigation.

Global Particulate Matter Source Apportionment

NASA Astrophysics Data System (ADS)

Lamancusa, C.; Wagstrom, K.

2017-12-01

As our global society develops and grows it is necessary to better understand the impacts and nuances of atmospheric chemistry, in particular those associated with atmospheric particulate matter. We have developed a source apportionment scheme for the GEOS-Chem global atmospheric chemical transport model. While these approaches have existed for several years in regional chemical transport models, the Global Particulate Matter Source Apportionment Technology (GPSAT) represents the first incorporation into a global chemical transport model. GPSAT runs in parallel to a standard GEOS-Chem run. GPSAT uses the fact that all molecules of a given species have the same probability of undergoing any given process as a core principle. This allows GPSAT to track many different species using only the flux information provided by GEOS-Chem's many processes. GPSAT accounts for the change in source specific concentrations as a result of aqueous and gas-phase chemistry, horizontal and vertical transport, condensation and evaporation on particulate matter, emissions, and wet and dry deposition. By using fluxes, GPSAT minimizes computational cost by circumventing the computationally costly chemistry and transport solvers. GPSAT will allow researchers to address many pertinent research questions about global particulate matter including the global impact of emissions from different source regions and the climate impacts from different source types and regions. For this first application of GPSAT, we investigate the contribution of the twenty largest urban areas worldwide to global particulate matter concentrations. The species investigated include: ammonium, nitrates, sulfates, and the secondary organic aerosols formed by the oxidation of benzene, isoprene, and terpenes. While GPSAT is not yet publically available, we will incorporate it into a future standard release of GEOS-Chem so that all GEOS-Chem users will have access to this new tool.

CARBON CONTAINING COMPONENT OF THE LOS ANGELES AEROSOL: SOURCE APPORTIONMENT AND CONTRIBUTIONS TO THE VISIBILITY BUDGET

EPA Science Inventory

Source resolution of the organic component of the fine fraction of the ambient aerosol (d(sub p) < 3.5 micrometers) has been carried out by combining source information from the organic component with thermal analysis and local emission inventories. The primary and secondary carb...

26 CFR 1.168(i)-0 - Table of contents for the general asset account rules.

Code of Federal Regulations, 2013 CFR

2013-04-01

...) Source of ordinary income, gain, or loss. (i) Source determined by allocation and apportionment of depreciation allowed. (ii) Formula for determining foreign source income, gain, or loss. (3) Section 904(d... disposed or converted asset. (k) Effect of adjustments on prior dispositions. (l) Election. (1) Irrevocable...

26 CFR 1.168(i)-0 - Table of contents for the general asset account rules.

Code of Federal Regulations, 2014 CFR

2014-04-01

...) Source of ordinary income, gain, or loss. (i) Source determined by allocation and apportionment of depreciation allowed. (ii) Formula for determining foreign source income, gain, or loss. (3) Section 904(d... disposed or converted asset. (k) Effect of adjustments on prior dispositions. (l) Election. (1) Irrevocable...

26 CFR 1.168(i)-0 - Table of contents for the general asset account rules.

Code of Federal Regulations, 2012 CFR

2012-04-01

...) Source of ordinary income, gain, or loss. (i) Source determined by allocation and apportionment of depreciation allowed. (ii) Formula for determining foreign source income, gain, or loss. (3) Section 904(d... disposed or converted asset. (k) Effect of adjustments on prior dispositions. (l) Election. (1) Irrevocable...

SEM-EDX analysis in the source apportionment of particulate matter on Hypogymnia physodes lichen transplants around the Cu smelter and former mining town of Karabash, South Urals, Russia.

PubMed

Williamson, B J; Mikhailova, I; Purvis, O W; Udachin, V

2004-04-25

Scanning electron microscopy with energy-dispersive X-ray analysis (SEM-EDX) of particulate matter on lichen transplant thalli (Hypogymnia physodes) was assessed as a complementary technique to wet chemical analysis for source apportionment of airborne contaminants. Transplants (2 month exposure) stationed in the Cu smelter and former mining town of Karabash were compared with those from a control site 30 km south. Particulate matter in Karabash samples (715 analyses) showed higher levels of S, Pb, Cu, Sn and Zn compared with the control (598 analyses). Complex element associations among the particles confounded detailed mineralogical identifications, and therefore a simplified particle classification scheme was devised for source apportionment. Karabash samples contained high levels of particles classified as mining-related (MRP), and these were also identified in control samples, indicating wide spatial dispersion from the smelter and highlighting the sensitivity of the method. It was noted that MRP <2.5-microm diameter were poorly represented on lichen surfaces suggesting this may limit the usefulness of Hypogymnia transplants as proxies when assessing human health impacts from airborne particulates. Analyses of the lichen thallus surface (away from surface particulates) revealed high levels of Cu, Zn, Fe and Pb associated with organics in the Karabash samples compared with the control, with a proportionate loss of K, interpreted as being due to a stress-related increase in cell membrane permeability. This type of analysis may provide a novel SEM-EDX-based method for assessing lichen vitality. The techniques developed are presented and further implications of the study are discussed.

RADIOCARBON SOURCE APPORTIONMENT IN A BIOFUELS ERA

EPA Science Inventory

Biofuels (gasohol and biodiesel) introduce radiocarbon into the U.S. mobile source fuel supply where it was previously absent. Initial measurements of radiocarbon in the PM_2.5 combustion emissions from engines using gasohol indicate that this may have less effect on r...

The source apportionment of polycyclic aromatic hydrocarbons (PAHs) in the topsoil in Xiaodian sewage irrigation area, North of China.

PubMed

Li, Jia-Le; Wang, Yan-Xin; Zhang, Cai-Xiang; Dong, Yi-Hui; Du, Bin; Liao, Xiao-Ping

2014-12-01

31 topsoil samples were collected by grid method in Xiaodian sewage irrigation area, Taiyuan City, North of China. The concentrations of 16 kinds of polycyclic aromatic hydrocarbons (PAHs) were determined by gas chromatograph coupled with mass spectrum. Generally speaking, the distribution order of PAHs in the area is: those with five and six rings > those with four rings > those with two and three rings. Source apportionment shows a significant zonation of the source of PAHs: the civil coal pollution occurred in the north part, the local and far factory pollution happened in the middle area and the mixed pollution sources from coal and wood combustion, automotive emission, presented in the south area. The distribution of PAHs has a definite relationship with the sewage water flow and soil adsorption. The related coefficient between PAHs and physicochemical property showed there was a negative correlation between pH, silt, clay and PAHs while there was a positive correlation between total organic carbon, sand and PAHs.

Vulnerability Assessment of Groundwater Resources by Nutrient Source Apportionment to Individual Groundwater Wells: A Case Study in North Carolina

NASA Astrophysics Data System (ADS)

Ayub, R.; Obenour, D. R.; Keyworth, A. J.; Genereux, D. P.; Mahinthakumar, K.

2016-12-01

Groundwater contamination by nutrients (nitrogen and phosphorus) is a major concern in water table aquifers that underlie agricultural areas in the mid-Atlantic Coastal Plain of the United States. High nutrient concentrations leaching into shallow groundwater can lead to human health problems and eutrophication of receiving surface waters. Liquid manure from concentrated animal feeding operations (CAFOs) stored in open-air lagoons and applied to spray fields can be a significant source of nutrients to groundwater, along with septic waste. In this study, we developed a model-based methodology for source apportionment and vulnerability assessment using sparse groundwater quality sampling measurements for Duplin County, North Carolina (NC), obtained by the NC Department of Environmental Quality (NC DEQ). This model provides information relevant to management by estimating the nutrient transport through the aquifer from different sources and addressing the uncertainty of nutrient contaminant propagation. First, the zones of influence (dependent on nutrient pathways) for individual groundwater monitoring wells were identified using a two-dimensional vertically averaged groundwater flow and transport model incorporating geologic uncertainty for the surficial aquifer system. A multiple linear regression approach is then applied to estimate the contribution weights for different nutrient source types using the nutrient measurements from monitoring wells and the potential sources within each zone of influence. Using the source contribution weights and their uncertainty, a probabilistic vulnerability assessment of the study area due to nutrient contamination is performed. Knowledge of the contribution of different nutrient sources to contamination at receptor locations (e.g., private wells, municipal wells, stream beds etc.) will be helpful in planning and implementation of appropriate mitigation measures.

SOURCE APPORTIONMENT OF INDOOR, OUTDOOR, AND PERSONAL PM2.5 IN SEATTLE, WASHINGTON, USING POSITIVE MATRIX FACTORIZATION

EPA Science Inventory

As part of a large exposure assessment and health effects panel study, 33 trace elements and light-absorbing carbon were measured on 24-hr particulate matter with an aero-dynamic diameter <2.5 um (PM2.5) fixed-site filter samples collected between September 26, 2000, and May 25, ...

PM10 source apportionment in Milan (Italy) using time-resolved data.

PubMed

Bernardoni, Vera; Vecchi, Roberta; Valli, Gianluigi; Piazzalunga, Andrea; Fermo, Paola

2011-10-15

In this work Positive Matrix Factorization (PMF) was applied to 4-hour resolved PM10 data collected in Milan (Italy) during summer and winter 2006. PM10 characterisation included elements (Mg-Pb), main inorganic ions (NH(4)(+), NO(3)(-), SO(4)(2-)), levoglucosan and its isomers (mannosan and galactosan), and organic and elemental carbon (OC and EC). PMF resolved seven factors that were assigned to construction works, re-suspended dust, secondary sulphate, traffic, industry, secondary nitrate, and wood burning. Multi Linear Regression was applied to obtain the PM10 source apportionment. The 4-hour temporal resolution allowed the estimation of the factor contributions during peculiar episodes, which would have not been detected with the traditional 24-hour sampling strategy. Copyright © 2011 Elsevier B.V. All rights reserved.

PARTICULATE ORGANIC SOURCE MARKERS IN THE NEW YORK CITY METROPOLITAN AREA

EPA Science Inventory

A sampling network of four sites was established for the Speciation of Organics for Apportionment of PM2.5 (SOAP) project during 2002-2003 to investigate composition, seasonal and spatial variability, and source contributions to particulate organic matter in the New York City met...

Constrained positive matrix factorization: Elemental ratios, spatial distinction, and chemical transport model source contributions

NASA Astrophysics Data System (ADS)

Sturtz, Timothy M.

Source apportionment models attempt to untangle the relationship between pollution sources and the impacts at downwind receptors. Two frameworks of source apportionment models exist: source-oriented and receptor-oriented. Source based apportionment models use presumed emissions and atmospheric processes to estimate the downwind source contributions. Conversely, receptor based models leverage speciated concentration data from downwind receptors and apply statistical methods to predict source contributions. Integration of both source-oriented and receptor-oriented models could lead to a better understanding of the implications sources have on the environment and society. The research presented here investigated three different types of constraints applied to the Positive Matrix Factorization (PMF) receptor model within the framework of the Multilinear Engine (ME-2): element ratio constraints, spatial separation constraints, and chemical transport model (CTM) source attribution constraints. PM10-2.5 mass and trace element concentrations were measured in Winston-Salem, Chicago, and St. Paul at up to 60 sites per city during two different seasons in 2010. PMF was used to explore the underlying sources of variability. Information on previously reported PM10-2.5 tire and brake wear profiles were used to constrain these features in PMF by prior specification of selected species ratios. We also modified PMF to allow for combining the measurements from all three cities into a single model while preserving city-specific soil features. Relatively minor differences were observed between model predictions with and without the prior ratio constraints, increasing confidence in our ability to identify separate brake wear and tire wear features. Using separate data, source contributions to total fine particle carbon predicted by a CTM were incorporated into the PMF receptor model to form a receptor-oriented hybrid model. The level of influence of the CTM versus traditional PMF was varied using a weighting parameter applied to an object function as implemented in ME-2. The resulting hybrid model was used to quantify the contributions of total carbon from both wildfires and biogenic sources at two Interagency Monitoring of Protected Visual Environment monitoring sites, Monture and Sula Peak, Montana, from 2006 through 2008.

77 FR 4510 - Air Quality Implementation Plans; Kentucky; Attainment Plan for the Kentucky Portion of the...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-30

... and population based apportionment of the area and nonroad sectors to support the mobile source... and nitrogen oxides (NO X ) for the mobile source contribution to ambient PM 2.5 levels for the.... Attainment Date B. Insignificance Determination for the Mobile Source Contribution to PM 2.5 and NO X...

Size-segregated aerosol in a hot-spot pollution urban area: Chemical composition and three-way source apportionment.

PubMed

Bernardoni, V; Elser, M; Valli, G; Valentini, S; Bigi, A; Fermo, P; Piazzalunga, A; Vecchi, R

2017-12-01

In this work, a comprehensive characterisation and source apportionment of size-segregated aerosol collected using a multistage cascade impactor was performed. The samples were collected during wintertime in Milan (Italy), which is located in the Po Valley, one of the main pollution hot-spot areas in Europe. For every sampling, size-segregated mass concentration, elemental and ionic composition, and levoglucosan concentration were determined. Size-segregated data were inverted using the program MICRON to identify and quantify modal contributions of all the measured components. The detailed chemical characterisation allowed the application of a three-way (3-D) receptor model (implemented using Multilinear Engine) for size-segregated source apportionment and chemical profiles identification. It is noteworthy that - as far as we know - this is the first time that three-way source apportionment is attempted using data of aerosol collected by traditional cascade impactors. Seven factors were identified: wood burning, industry, resuspended dust, regional aerosol, construction works, traffic 1, and traffic 2. Further insights into size-segregated factor profiles suggested that the traffic 1 factor can be associated to diesel vehicles and traffic 2 to gasoline vehicles. The regional aerosol factor resulted to be the main contributor (nearly 50%) to the droplet mode (accumulation sub-mode with modal diameter in the range 0.5-1 μm), whereas the overall contribution from the two factors related to traffic was the most important one in the other size modes (34-41%). The results showed that applying a 3-D receptor model to size-segregated samples allows identifying factors of local and regional origin while receptor modelling on integrated PM fractions usually singles out factors characterised by primary (e.g. industry, traffic, soil dust) and secondary (e.g. ammonium sulphate and nitrate) origin. Furthermore, the results suggested that the information on size-segregated chemical composition in different size classes was exploited by the model to relate primary emissions to rapidly-formed secondary compounds. Copyright © 2017 Elsevier Ltd. All rights reserved.

Close ISR Support: Re-organizing the Combined Forces Air Component Commander’s Intelligence, Surveillance and Reconnaissance Processes and Agencies

DTIC Science & Technology

2009-12-01

instruction, searching existing data sources , gathering and maintaining the data needed, and completing and reviewing the collection of information...146 1. Allocation vs. Apportionment .........................................................146 2. Collection Management Authority...290 D. MEASUREMENT AND SIGNATURE INTELLIGENCE .....................291 E. OPEN- SOURCE

THE WORKSHOP ON THE SOURCE APPORTIONMENT OF PM HEALTH EFFECTS: INTER-COMPARISON OF RESULTS AND IMPLICATIONS

EPA Science Inventory

While the association between exposure to ambient fine particulate matter mass (PM2.5) and human mortality is well established, the most responsible particle types/sources are not yet certain. In May 2003, the U.S. Environmental Protection Agency's Particulate Matter Centers Prog...

Source Apportionment of Primary and Secondary Organic Aerosol Using Positive Matrix Factorization (PMF) of Molecular Markers

EPA Science Inventory

Monthly average ambient concentrations of more than eighty particle-phase organic compounds, as well as total organic carbon (OC) and elemental carbon (EC), were measured from March 2004 through February 2005 in five cities in the Midwestern United States. A multi-variant source...

The Denver Aerosol Sources and Health (DASH) Study: Overview and Early Findings

PubMed Central

Vedal, S.; Hannigan, M.P.; Dutton, S.J.; Miller, S. L.; Milford, J.B.; Rabinovitch, N.; Kim, S.-Y.; Sheppard, L.

2012-01-01

Improved understanding of the sources of air pollution that are most harmful could aid in developing more effective measures for protecting human health. The Denver Aerosol Sources and Health (DASH) study was designed to identify the sources of ambient fine particulate matter (PM2.5) that are most responsible for the adverse health effects of short-term exposure to PM 2.5. Daily 24-hour PM2.5 sampling began in July 2002 at a residential monitoring site in Denver, Colorado, using both Teflon and quartz filter samplers. Sampling is planned to continue through 2008. Chemical speciation is being carried out for mass, inorganic ionic compounds (sulfate, nitrate and ammonium), and carbonaceous components, including elemental carbon, organic carbon, temperature-resolved organic carbon fractions and a large array of organic compounds. In addition, water soluble metals were measured daily for 12 months in 2003. A receptor-based source apportionment approach utilizing positive matrix factorization (PMF) will be used to identify PM 2.5 source contributions for each 24-hour period. Based on a preliminary assessment using synthetic data, the proposed source apportionment should be able to identify many important sources on a daily basis, including secondary ammonium nitrate and ammonium sulfate, diesel vehicle exhaust, road dust, wood combustion and vegetative debris. Meat cooking, gasoline vehicle exhaust and natural gas combustion were more challenging for PMF to accurately identify due to high detection limits for certain organic molecular marker compounds. Measurements of these compounds are being improved and supplemented with additional organic molecular marker compounds. The health study will investigate associations between daily source contributions and an array of health endpoints, including daily mortality and hospitalizations and measures of asthma control in asthmatic children. Findings from the DASH study, in addition to being of interest to policymakers, by identifying harmful PM2.5 sources may provide insights into mechanisms of PM effect. PMID:22723735

The Denver Aerosol Sources and Health (DASH) study: Overview and early findings

NASA Astrophysics Data System (ADS)

Vedal, S.; Hannigan, M. P.; Dutton, S. J.; Miller, S. L.; Milford, J. B.; Rabinovitch, N.; Kim, S.-Y.; Sheppard, L.

Improved understanding of the sources of air pollution that are most harmful could aid in developing more effective measures for protecting human health. The Denver Aerosol Sources and Health (DASH) study was designed to identify the sources of ambient fine particulate matter (PM 2.5) that are most responsible for the adverse health effects of short-term exposure to PM 2.5. Daily 24-h PM 2.5 sampling began in July 2002 at a residential monitoring site in Denver, Colorado, using both Teflon and quartz filter samplers. Sampling is planned to continue through 2008. Chemical speciation is being carried out for mass, inorganic ionic compounds (sulfate, nitrate and ammonium), and carbonaceous components, including elemental carbon, organic carbon, temperature-resolved organic carbon fractions and a large array of organic compounds. In addition, water-soluble metals were measured daily for 12 months in 2003. A receptor-based source apportionment approach utilizing positive matrix factorization (PMF) will be used to identify PM 2.5 source contributions for each 24-h period. Based on a preliminary assessment using synthetic data, the proposed source apportionment should be able to identify many important sources on a daily basis, including secondary ammonium nitrate and ammonium sulfate, diesel vehicle exhaust, road dust, wood combustion and vegetative debris. Meat cooking, gasoline vehicle exhaust and natural gas combustion were more challenging for PMF to accurately identify due to high detection limits for certain organic molecular marker compounds. Measurements of these compounds are being improved and supplemented with additional organic molecular marker compounds. The health study will investigate associations between daily source contributions and an array of health endpoints, including daily mortality and hospitalizations and measures of asthma control in asthmatic children. Findings from the DASH study, in addition to being of interest to policymakers, by identifying harmful PM 2.5 sources may provide insights into mechanisms of PM effect.

PM2.5 Source Apportionment: Reconciling Receptor Models for U.S. Nonurban and Urban Long-Term Networks.

PubMed

Chen, L-W Antony; Watson, John G; Chow, Judith C; DuBois, Dave W; Herschberger, Lisa

2011-11-01

Chemical mass balance (CMB) and trajectory receptor models were applied to speciated particulate matter with aerodynamic diameter ≤2.5 μm (PM 2.5 ) measurements from Speciation Trends Network (STN; part of the Chemical Speciation Network [CSN]) and Interagency Monitoring of Protected Visual Environments (IMPROVE) monitoring network across the state of Minnesota as part of the Minnesota PM 2.5 Source Apportionment Study (MPSAS). CMB equations were solved by the Unmix, positive matrix factorization (PMF), and effective variance (EV) methods, giving collective source contribution and uncertainty estimates. Geological source profiles developed from local dust materials were either incorporated into the EV-CMB model or used to verify factors derived from Unmix and PMF. Common sources include soil dust, calcium (Ca)-rich dust, diesel and gasoline vehicle exhausts, biomass burning, secondary sulfate, and secondary nitrate. Secondary sulfate and nitrate aerosols dominate PM 2.5 mass (50-69%). Mobile sources outweigh area sources at urban sites, and vice versa at rural sites due to traffic emissions. Gasoline and diesel contributions can be separated using data from the STN, despite significant uncertainties. Major differences between MPSAS and earlier studies on similar environments appear to be the type and magnitude of stationary sources, but these sources are generally minor (<7%) in this and other studies. Ensemble back-trajectory analysis shows that the lower Midwestern states are the predominant source region for secondary ammoniated sulfate in Minnesota. It also suggests substantial contributions of biomass burning and soil dust from out-of-state on occasions, although a quantitative separation of local and regional contributions was not achieved in the current study. Supplemental materials are available for this article. Go to the publisher's online edition of the Journal of the Air & Waste Management Association for a summary of input data, Unmix and PMF factor profiles, and additional maps. [Box: see text].

Source Contributions of Urban PM2.5 in the Beijing-Tianjin-Hebei Region: Changes between 2006 and 2013 and Relative Impacts of Emissions and Meteorology

NASA Astrophysics Data System (ADS)

Li, X.; Zhang, Q.; Zhang, Y.; Zheng, B.; Li, M.; Wang, K.; Chen, Y.; Wallington, T. J.; Han, W.; Shen, W.; Zhang, X.; He, K.

2015-12-01

Anthropogenic emissions in China have been controlled for years to improve ambient air quality. However, severe haze events caused by atmospheric aerosols with aerodynamic diameter less than or equal to 2.5 μm (PM2.5) have continued to occur, especially in the Beijing-Tianjin-Hebei (BTH) region. The Chinese government has set an ambitious goal to reduce urban PM2.5 concentrations by 25% in BTH by 2017 relative to the 2012 levels. Source apportionment (SA) is necessary to the development of the effective emission control strategies. In this work, the Comprehensive Air Quality Model with extensions (CAMx) with the Particulate Source Apportionment Technology (PSAT) is applied to the China domain for the years 2006 and 2013. Ambient surface concentrations of PM2.5 and its components are generally well reproduced. To quantify the contributions of each emission category or region to PM2.5 in BTH, the total emissions are divided into 7 emission categories and 11 source regions. The source contributions determined in this work are generally consistent with results from previous work. In 2013, the industrial (44%) and residential (27%) sectors are the dominant contributors to urban PM2.5 in BTH. The residential sector is the largest contributor in winter; the industry sector dominates in other seasons. A slight increasing trend (+3% for industry and +6% for residential) is found in 2013 relative to 2006, necessitating more attention to these two sectors. Local emissions make the largest contribution (40%-60%) for all receptors. Change of source contribution of PM2.5 in Beijing and northern Hebei are dominate by change of local emission. However, for Tianjin, and central and southern Hebei, change of meteorology condition are as important as change of emission, because regional inflow in these areas is more important than in Beijing and northern Hebei and can increase under unfavorable weather conditions, indicating a strong need for regional joint emission control efforts. The results in this study enhance the quantitative understanding of the source-receptor relationships and provide an important basis for policymaking to advance the control of PM2.5 pollution in China. Both sector-based and fuel-based source apportionment will be available to further improve the comparability with receptor model results.

Two years of near real-time observations of the chemical composition of submicron aerosols in Cape Corsica obtained by Q-ACSM

NASA Astrophysics Data System (ADS)

Sciare, Jean; Dulac, François; Crenn, Vincent; Hamonou, Eric; Baisnée, Dominique; Nicolas, José B.; Pont, Véronique; Lambert, Dominique; Gheusi, François; Mallet, Marc; Tison, Emmanuel; Sauvage, Stéphane; Bourrianne, Thierry; Roberts, Gregory; Colomb, Aurélie; Pichon, Jean-Marc; Sellegri, Karine; Savelli, Jean-Luc

2015-04-01

As part of the MISTRALS/ChArMEx (Mediterranean Integrated Studies aT Regional And Local Scales/the Chemistry-Aerosol Mediterranean Experiment; http://www.mistrals-home.org; http://charmex.lsce.ipsl.fr) and the CORSiCA (http://www.obs-mip.fr/corsica) programs, 2-year continuous observations of near real-time chemical composition of submicron aerosols were performed between June 2012 & July 2014 at the Cape Corsica atmospheric supersite (http://gaw.empa.ch/gawsis/reports.asp?StationID=2076203042), a remote marine site in the Western Mediterranean. Submicron organic aerosols (OA) and the major inorganic salts (sulfate, ammonium, nitrate) were monitored every 30 min using a Quadripole Aerosol Chemical Speciation Monitor (Q-ACSM; Aerodyne Res. Inc. MA, USA). Quality control of this large dataset (24-month continuous observations) was performed through closure studies (using co-located SMPS and TEOM-FDMS measurements), direct comparisons with other on-line / off-line instruments running in parallel (filter sampling, OPC, nephelometer …), and large intercomparison of 13 Q-ACSM performed within the EU-FP7 ACTRIS program (http://www.actris.net/). Source apportionment of OA was then performed on a monthly basis using the SourceFinder software (SoFi, http://www.psi.ch/acsm-stations/me-2) allowing the distinction between hydrogen- and oxygen-like organic aerosols (HOA and OOA, respectively). This monthly resolved source apportionment was first compared with co-located real-time tracer measurements (NOx, BC, CO, VOC …) available at the Cape Corsica station. Seasonal patterns of the various properties of (secondary) OOA (OSc, O/C ratio …) were then investigated from monthly resolved source apportionment results (monthly OOA mass spectra) obtained over the period June 2012 - July 2014. Acknowledgements: Atmospheric measurements performed at Cape Corsica Station were funded by CNRS-INSU, ADEME, CEA, and METEO-FRANCE. This work was carried out in the framework of the CORSiCA project funded by the Collectivité Territoriale de Corse through the Fonds Européen de Développement Régional of the European Operational Program 2007-2013 and the Contrat de Plan Etat Région.

Source apportionment of PAH in Hamilton Harbour suspended sediments: comparison of two factor analysis methods.

PubMed

Sofowote, Uwayemi M; McCarry, Brian E; Marvin, Christopher H

2008-08-15

A total of 26 suspended sediment samples collected over a 5-year period in Hamilton Harbour, Ontario, Canada and surrounding creeks were analyzed for a suite of polycyclic aromatic hydrocarbons and sulfur heterocycles. Hamilton Harbour sediments contain relatively high levels of polycyclic aromatic compounds and heavy metals due to emissions from industrial and mobile sources. Two receptor modeling methods using factor analyses were compared to determine the profiles and relative contributions of pollution sources to the harbor; these methods are principal component analyses (PCA) with multiple linear regression analysis (MLR) and positive matrix factorization (PMF). Both methods identified four factors and gave excellent correlation coefficients between predicted and measured levels of 25 aromatic compounds; both methods predicted similar contributions from coal tar/coal combustion sources to the harbor (19 and 26%, respectively). One PCA factor was identified as contributions from vehicular emissions (61%); PMF was able to differentiate vehicular emissions into two factors, one attributed to gasoline emissions sources (28%) and the other to diesel emissions sources (24%). Overall, PMF afforded better source identification than PCA with MLR. This work constitutes one of the few examples of the application of PMF to the source apportionment of sediments; the addition of sulfur heterocycles to the analyte list greatly aided in the source identification process.

Positive matrix factorization as source apportionment of soil lead and cadmium around a battery plant (Changxing County, China).

PubMed

Xue, Jian-long; Zhi, Yu-you; Yang, Li-ping; Shi, Jia-chun; Zeng, Ling-zao; Wu, Lao-sheng

2014-06-01

Chemical compositions of soil samples are multivariate in nature and provide datasets suitable for the application of multivariate factor analytical techniques. One of the analytical techniques, the positive matrix factorization (PMF), uses a weighted least square by fitting the data matrix to determine the weights of the sources based on the error estimates of each data point. In this research, PMF was employed to apportion the sources of heavy metals in 104 soil samples taken within a 1-km radius of a lead battery plant contaminated site in Changxing County, Zhejiang Province, China. The site is heavily contaminated with high concentrations of lead (Pb) and cadmium (Cd). PMF successfully partitioned the variances into sources related to soil background, agronomic practices, and the lead battery plants combined with a geostatistical approach. It was estimated that the lead battery plants and the agronomic practices contributed 55.37 and 29.28%, respectively, for soil Pb of the total source. Soil Cd mainly came from the lead battery plants (65.92%), followed by the agronomic practices (21.65%), and soil parent materials (12.43%). This research indicates that PMF combined with geostatistics is a useful tool for source identification and apportionment.

Quantifying the uncertainty of nonpoint source attribution in distributed water quality models: A Bayesian assessment of SWAT's sediment export predictions

NASA Astrophysics Data System (ADS)

Wellen, Christopher; Arhonditsis, George B.; Long, Tanya; Boyd, Duncan

2014-11-01

Spatially distributed nonpoint source watershed models are essential tools to estimate the magnitude and sources of diffuse pollution. However, little work has been undertaken to understand the sources and ramifications of the uncertainty involved in their use. In this study we conduct the first Bayesian uncertainty analysis of the water quality components of the SWAT model, one of the most commonly used distributed nonpoint source models. Working in Southern Ontario, we apply three Bayesian configurations for calibrating SWAT to Redhill Creek, an urban catchment, and Grindstone Creek, an agricultural one. We answer four interrelated questions: can SWAT determine suspended sediment sources with confidence when end of basin data is used for calibration? How does uncertainty propagate from the discharge submodel to the suspended sediment submodels? Do the estimated sediment sources vary when different calibration approaches are used? Can we combine the knowledge gained from different calibration approaches? We show that: (i) despite reasonable fit at the basin outlet, the simulated sediment sources are subject to uncertainty sufficient to undermine the typical approach of reliance on a single, best fit simulation; (ii) more than a third of the uncertainty of sediment load predictions may stem from the discharge submodel; (iii) estimated sediment sources do vary significantly across the three statistical configurations of model calibration despite end-of-basin predictions being virtually identical; and (iv) Bayesian model averaging is an approach that can synthesize predictions when a number of adequate distributed models make divergent source apportionments. We conclude with recommendations for future research to reduce the uncertainty encountered when using distributed nonpoint source models for source apportionment.

Importance of data comparability for multi-year trends and source apportionment of NMHC concentrations observed in France

NASA Astrophysics Data System (ADS)

Sauvage, Stéphane; Waked, Antoine; Leonardis, Thierry; Locoge, Nadine

2017-04-01

Non Methane Hydrocarbon Compounds (NMHCs) are of interest due to their potential health impact and their key role in atmospheric processes as precursors of secondary pollutants such as ozone (O3) and secondary organic aerosols (SOA). Hourly measurements of 31 non-methane hydrocarbons (NMHCs) were carried out at three urban sites in France over the period of a decade. The trends analysis showed a significant yearly decrease in pollutant concentrations over the study period and for the majority of species in the range of -1 to -7% in accordance with the decrease of NMHC emissions in France (-5 to -9%). Concentrations of long-lived species such as ethane and propane which are known as tracers of distant sources and natural gas remained constant. These trends are consistent with those recently described at urban and background sites in the northern mid-latitudes and with emission inventories. They are compared with the ones reported for 3 French rural sites (EMEP). A year per year source apportionment study using PMF was also conducted for 2 of the urban sites over the period 2005-2013. Using source fingerprints, five common anthropogenic sources were identified for Paris and Strasbourg: traffic-exhaust emissions (21±5%, 18±5%), evaporative sources (17±4%, 24±7%), natural gas & background (22±5%, 25±5%), residential heating (17±4%, 17±5%) and solvent use (19±7%, 12±5%). Biogenic sources were also identified and accounted for 4±1% of the total measured NMHC's at both sites. Along the presentation, the robustness of these results will be discussed regarding the site representativeness, the data comparability, and the temporal variation of the data quality

Urban PM in Eastern Germany: Source apportionment and contributions from different spatial scales

NASA Astrophysics Data System (ADS)

van Pinxteren, D.; Fomba, K. W.; Mothes, F.; Spindler, G.; Herrmann, H.

2017-12-01

Understanding the contributions of particulate matter (PM) sources and the source areas impacting total PM levels in a city are important requirements for further developing clean air policies and efficient abatement strategies. This presentation reports on two studies in Eastern Germany providing a detailed picture of present-day urban PM sources and discriminating contributions of local, regional and long-range sources. The "Leipzig Aerosol 2013-15" study yielded contributions of 12 sources to coarse, fine, and ultrafine particles, resolved by Positive Matrix Factorization (PMF) from comprehensive chemical speciation of 5-stage Berner impactor samples at 4 different sites in the Leipzig area. Dominant winter-time sources were traffic exhaust and non-exhaust emissions, secondary aerosol formation, and combustion emissions from both biomass and coal burning with different relative importance in different particle size ranges. Local sources dominated PM levels in ultrafine and coarse particles (60% - 80%) while high mass concentrations in accumulation mode particles mainly resulted from regional import into the city (70%). The "PM-East" study compiled PM10 mass and constituents' concentrations at 10 urban and rural sites in Eastern Germany during winter 2016/17, which included a 3-week episode of frequent exceedances of the PM10 limit value. PMF source apportionment is performed for a subset of the sites, including the city of Berlin. Contributions from short-, mid-, and long-range sources, including trans-boundary pollution import from neighbouring countries, are quantitatively assessed by advanced back trajectory statistical methods. Data analysis in PM-East is ongoing and final results will be available by November. Funding is acknowledged from 4 federal states of Germany: Berlin Senate Department for Environment, Transport and Climate Protection; Saxon State Office for Environment, Agriculture and Geology; State Agency for Environment, Nature Conservation and Geology Mecklenburg-Vorpommern; and Brandenburg State Office for Environment.

A stable isotope model for combined source apportionment and degradation quantification of environmental pollutants

NASA Astrophysics Data System (ADS)

Lutz, Stefanie; Van Breukelen, Boris

2014-05-01

Natural attenuation can represent a complementary or alternative approach to engineered remediation of polluted sites. In this context, compound specific stable isotope analysis (CSIA) has proven a useful tool, as it can provide evidence of natural attenuation and assess the extent of in-situ degradation based on changes in isotope ratios of pollutants. Moreover, CSIA can allow for source identification and apportionment, which might help to identify major emission sources in complex contamination scenarios. However, degradation and mixing processes in aquifers can lead to changes in isotopic compositions, such that their simultaneous occurrence might complicate combined source apportionment (SA) and assessment of the extent of degradation (ED). We developed a mathematical model (stable isotope sources and sinks model; SISS model) based on the linear stable isotope mixing model and the Rayleigh equation that allows for simultaneous SA and quantification of the ED in a scenario of two emission sources and degradation via one reaction pathway. It was shown that the SISS model with CSIA of at least two elements contained in the pollutant (e.g., C and H in benzene) allows for unequivocal SA even in the presence of degradation-induced isotope fractionation. In addition, the model enables precise quantification of the ED provided degradation follows instantaneous mixing of two sources. If mixing occurs after two sources have degraded separately, the model can still yield a conservative estimate of the overall extent of degradation. The SISS model was validated against virtual data from a two-dimensional reactive transport model. The model results for SA and ED were in good agreement with the simulation results. The application of the SISS model to field data of benzene contamination was, however, challenged by large uncertainties in measured isotope data. Nonetheless, the use of the SISS model provided a better insight into the interplay of mixing and degradation processes at the field site, as it revealed the prevailing contribution of one emission source and a low overall ED. The model can be extended to a larger number of sources and sinks. It may aid in forensics and natural attenuation assessment of soil, groundwater, surface water, or atmospheric pollution.

Organic tracer-based source analysis of PM2.5 organic and elemental carbon: A case study at Dongguan in the Pearl River Delta, China

NASA Astrophysics Data System (ADS)

Wang, Qiong Qiong; Huang, X. H. Hilda; Zhang, Ting; Zhang, Qingyan; Feng, Yongming; Yuan, Zibing; Wu, Dui; Lau, Alexis K. H.; Yu, Jian Zhen

2015-10-01

Organic carbon (OC) and elemental carbon (EC) are major constituents of PM2.5 and their source apportionment remains a challenging task due to the great diversity of their sources and lack of source-specific tracer data. In this work, sources of OC and EC are investigated using positive matrix factorization (PMF) analysis of PM2.5 chemical composition data, including major ions, OC, EC, elements, and organic molecular source markers, for a set of 156 filter samples collected over three years from 2010 to 2012 at Dongguan in the Pearl River Delta, China. The key organic tracers include levoglucosan, mannosan, hopanes, C27-C33n-alkanes, and polycyclic aromatic hydrocarbons (PAHs). Using these species as input for the PMF model, nine factors were resolved. Among them, biomass burning and coal combustion were significant sources contributing 15-17% of OC and 24-30% and 34-35% of EC, respectively. Industrial emissions and ship emissions, identified through their characteristic metal signatures, contributed 16-24% and 7-8% of OC and 8-11% and 16-17% of EC, respectively. Vehicle exhaust was a less significant source, accounting for 3-4% of OC and 5-8% of EC. Secondary OC, taken to be the sum of OC present in secondary sulfate and nitrate formation source factors, made up 27-36% of OC. Plastic burning, identified through 1,3,5-triphenylbenzene as a tracer, was a less important source for OC(≤4%) and EC (5-10%), but a significant source for PAHs at this site. The utility of organic source tracers was demonstrated by comparing PMF runs with different combinations of organic tracers removed from the input species list. Levoglucosan and mannosan were important additions to distinguish biomass burning from coal combustion by reducing collinearity among source profiles. Inclusion of hopanes and 1,3,5-triphenylbenzene was found to be necessary in resolving the less significant sources vehicle exhaust and plastic burning. Inclusion of C27-C33n-alkanes and PAHs can influence the source profiles resolved by PMF and thereby affect the source contributions to OC and EC. Considerably more OC (44% vs. 27% of OC) was apportioned to the secondary factors when only major components were considered in comparison with the PMF analysis with the full suite of organic tracers, mainly at the expense of coal combustion and industrial emissions. EC apportionment to the few major combustion sources was found more sensitive to inclusion of organic tracers than OC apportionment, with PAHs playing a prominent role. This work demonstrates the importance of having distinct organic tracers in identifying and quantifying OC and EC sources.

SOURCE APPORTIONMENT OF PM2.5 AT AN URBAN IMPROVE SITE IN SEATTLE, WA

EPA Science Inventory

The multivariate receptor models Positive Matrix Factorization (PMF) and Unmix were used along with EPA's Chemical Mass Balance model to deduce the sources of PM2.5 at a centrally located urban site in Seattle, Washington. A total of 289 filter samples were obtained with an IM...

77 FR 11798 - Approval and Promulgation of Air Quality Implementation Plans; Rhode Island; Regional Haze

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-28

...; and Lye Brook Wilderness Area in Vermont. Through source apportionment modeling, MANE-VU assisted... sources and activities which are located across a broad geographic area and emit fine particles and their...., sulfates, nitrates, organic carbon, elemental carbon, and soil dust), which also impair visibility by...

Variation in nitrate isotopic signatures in sewage for source apportionment with urbanization: a case study in Beijing, China.

PubMed

Xian, Chaofan; Ouyang, Zhiyun; Li, Yanmin; Xiao, Yang; Ren, Yufen

2016-11-01

Nitrate (NO 3 - ) pollution is a severe problem in urban aquatic systems especially within megacity undergoing rapid urbanization, and mostly, sewage is supposed as the prevailing NO 3 - source. A dual isotope approach (δ 15 N-NO 3 - and δ 18 O-NO 3 - ) was applied to explore the variation in NO 3 - isotopic signatures in sewage processed by wastewater treatment plants (WWTPs) in Beijing from 2014 to 2015. We found that the raw and treated sewage owned the different NO 3 - isotopic signatures, including δ 15 N from 1.1 to 24.7 ‰ and δ 18 O from 1.6 to 22.8 ‰ in raw sewage, as well as δ 15 N from 6.1 to 22.8 ‰ and δ 18 O from 1.6 to 13.2 ‰ in treated effluents. The WWTP processing would result in the enrichment of NO 3 - isotopic compositions in discharged effluents with NO 3 - concentrations increasing. Besides, advanced sewage treatment technology with more pollutant N reduction may raise the heavier NO 3 - isotopic compositions further. The NO 3 - isotope value ranges of urban sewage and manure should be separated, and the seasonal and tighter NO 3 - isotope value ranges are supposed to improve the accuracy of source apportionment. The NO 3 - isotope value ranges conducted in this study might provide useful information for tracing NO 3 - sources towards the implementation of efficient water pollution control in Beijing.

Improved source apportionment of organic aerosols in complex urban air pollution using the multilinear engine (ME-2)

NASA Astrophysics Data System (ADS)

Zhu, Qiao; Huang, Xiao-Feng; Cao, Li-Ming; Wei, Lin-Tong; Zhang, Bin; He, Ling-Yan; Elser, Miriam; Canonaco, Francesco; Slowik, Jay G.; Bozzetti, Carlo; El-Haddad, Imad; Prévôt, André S. H.

2018-02-01

Organic aerosols (OAs), which consist of thousands of complex compounds emitted from various sources, constitute one of the major components of fine particulate matter. The traditional positive matrix factorization (PMF) method often apportions aerosol mass spectrometer (AMS) organic datasets into less meaningful or mixed factors, especially in complex urban cases. In this study, an improved source apportionment method using a bilinear model of the multilinear engine (ME-2) was applied to OAs collected during the heavily polluted season from two Chinese megacities located in the north and south with an Aerodyne high-resolution aerosol mass spectrometer (HR-ToF-AMS). We applied a rather novel procedure for utilization of prior information and selecting optimal solutions, which does not necessarily depend on other studies. Ultimately, six reasonable factors were clearly resolved and quantified for both sites by constraining one or more factors: hydrocarbon-like OA (HOA), cooking-related OA (COA), biomass burning OA (BBOA), coal combustion (CCOA), less-oxidized oxygenated OA (LO-OOA) and more-oxidized oxygenated OA (MO-OOA). In comparison, the traditional PMF method could not effectively resolve the appropriate factors, e.g., BBOA and CCOA, in the solutions. Moreover, coal combustion and traffic emissions were determined to be primarily responsible for the concentrations of PAHs and BC, respectively, through the regression analyses of the ME-2 results.

New directions: Beyond sulphur, vanadium and nickel - About source apportionment of ship emissions in emission control areas

NASA Astrophysics Data System (ADS)

Czech, Hendryk; Schnelle-Kreis, Jürgen; Streibel, Thorsten; Zimmermann, Ralf

2017-08-01

During the oil crises of the 70s and the associated increase of the oil price, the usage of marine fuels shifted from middle distillates of the crude oil refinery, such as marine diesel oil (MDO) or marine gas oil (MGO), towards cheaper heavy fuel oils (HFO), or also called residual fuel oil. The latter refers to the vacuum residue of the crude oil refinery blended by lighter refinery products, such as kerosene, to meet a certain maximum viscosity. Those HFOs are rich in sulphur and heavy metals which end up as significant constituents in emitted fine particulate matter (PM2.5) after the combustion. Especially for harbour cities or highly frequented ship traffic routes, HFO-derived PM2.5 has been identified as a globally important perpetrator of increased mortality by cardiopulmonary diseases and lung cancer (e.g. Corbett et al., 2007). However, the emitted hazardous species provide reliable markers to assess the contribution of this emission source to air pollution in source apportionment studies. Such studies are often performed utilising positive matrix factorisation, whose score matrix can be interpreted as temporal contribution of k identified emission sources and factors represent the k corresponding emission profiles. If one of the k factors contains moderate to high amounts of sulphate, vanadium and nickel with a high ratio of the two latter ones, the ship identification was unambiguous (e.g. Viana et al., 2009). Even more sensitive towards emission profiles are receptor models such as chemical mass balance, which require detailed prior knowledge about the assumed emission sources (Jeong et al., 2017).

Characteristics and source apportionment of PM2.5 during persistent extreme haze events in Chengdu, southwest China

NASA Astrophysics Data System (ADS)

Li, L.; Liu, S.

2017-12-01

Based on detailed data from Chengdu Plain (CP) from 6 January to 16 January 2015 , two typical haze episodes were analyzed to clarify the haze formation mechanism in winter. Weather conditions, chemical compositions, secondary pollutant transformation, optical properties of aerosols, the potential source contribution function (PSCF) and source apportionment were studied. The planetary boundary layer (PBL) height decreased distinctly during the haze episodes and restrained air pollutant vertical dispersion. As the haze worsened, the value of PBL × PM2.5 increased notably. The [NO3-]/[SO42-] ratio was 0.61, 0.76 and 0.88 during a non-haze period, episode 1 and episode 2, respectively, indicating that the mobile source of the air pollution is increasingly predominant in Chengdu. Water vapor also played a vital role in the formation of haze by accelerating the chemical transformation of secondary pollutants, leading to the hygroscopic growth of aerosols. The PSCF and backward trajectories of the air masses indicated that the pollution mainly came from the south. The secondary inorganic aerosols, vehicle emissions, coal combustion, biomass burning, industry, and dust contributed 34.1%, 24.1%, 12.7%, 12.3%, 7.6%, and 7.2% to PM2.5 masses in episode 1 and 28.9%, 23.1%, 9.4%, 9.5%, 20.3% and 7.5% in episode 2.

Characteristics and source apportionment of PM2.5 during persistent extreme haze events in Chengdu, southwest China.

PubMed

Li, Lulu; Tan, Qinwen; Zhang, Yuanhang; Feng, Miao; Qu, Yu; An, Junling; Liu, Xingang

2017-11-01

Based on detailed data from Chengdu Plain (CP) from 6 January to 16 January, two typical haze episodes were analyzed to clarify the haze formation mechanism in winter. Weather conditions, chemical compositions, secondary pollutant transformation, optical properties of aerosols, the potential source contribution function (PSCF) and source apportionment were studied. The planetary boundary layer (PBL) height decreased distinctly during the haze episodes and restrained air pollutant vertical dispersion. As the haze worsened, the value of PBL × PM 2.5 increased notably. The [NO 3 - ]/[SO 4 2- ] ratio was 0.61, 0.76 and 0.88 during a non-haze period, episode 1 and episode 2, respectively, indicating that the mobile source of the air pollution is increasingly predominant in Chengdu. Water vapor also played a vital role in the formation of haze by accelerating the chemical transformation of secondary pollutants, leading to the hygroscopic growth of aerosols. The PSCF and backward trajectories of the air masses indicated that the pollution mainly came from the south. The secondary inorganic aerosols, vehicle emissions, coal combustion, biomass burning, industry, and dust contributed 34.1%, 24.1%, 12.7%, 12.3%, 7.6%, and 7.2% to PM 2.5 masses in episode 1 and 28.9%, 23.1%, 9.4%, 9.5%, 20.3% and 7.5% in episode 2. Copyright © 2017 Elsevier Ltd. All rights reserved.

Composition and source apportionment of dust fall around a natural lake.

PubMed

Latif, Mohd Talib; Ngah, Sofia Aida; Dominick, Doreena; Razak, Intan Suraya; Guo, Xinxin; Srithawirat, Thunwadee; Mushrifah, Idris

2015-07-01

The aim of this study was to determine the source apportionment of dust fall around Lake Chini, Malaysia. Samples were collected monthly between December 2012 and March 2013 at seven sampling stations located around Lake Chini. The samples were filtered to separate the dissolved and undissolved solids. The ionic compositions (NO3-, SO4(2-), Cl- and NH4+) were determined using ion chromatography (IC) while major elements (K, Na, Ca and Mg) and trace metals (Zn, Fe, Al, Ni, Mn, Cr, Pb and Cd) were determined using inductively coupled plasma mass spectrometry (ICP-MS). The results showed that the average concentration of total solids around Lake Chini was 93.49±16.16 mg/(m2·day). SO4(2-), Na and Zn dominated the dissolved portion of the dust fall. The enrichment factors (EF) revealed that the source of the trace metals and major elements in the rain water was anthropogenic, except for Fe. Hierarchical agglomerative cluster analysis (HACA) classified the seven monitoring stations and 16 variables into five groups and three groups respectively. A coupled receptor model, principal component analysis multiple linear regression (PCA-MLR), revealed that the sources of dust fall in Lake Chini were dominated by agricultural and biomass burning (42%), followed by the earth's crust (28%), sea spray (16%) and a mixture of soil dust and vehicle emissions (14%). Copyright © 2015. Published by Elsevier B.V.

Understanding the Impacts of Land Uses on the Source Apportionment of Atmospheric Contamination By Polycyclic Aromatic Hydrocarbons throughout a Small State in the Northeast United States

NASA Astrophysics Data System (ADS)

Schifman, L. A.; Boving, T. B.

2014-12-01

Polycyclic aromatic hydrocarbons (PAH) are ubiquitous contaminants that enter the environment through combustion processes and are often found in higher concentration of urban areas. However, once released, these compounds can travel long distances via transport through the atmosphere and can be deposited on the landscape far away from their original source. This PAH deposition pattern can slowly lead to the diffuse contamination of whole landscapes. Since most of the air masses entering the northeastern United States originate from the Midwest where coal burning power plants are plentiful, several atmospheric pollutants are introduced to the region in addition to local sources. Here, atmospheric deposition of PAHs in six different locations throughout Rhode Island was measured using passive bulk-deposition samplers for 3 years. The data were analyzed statistically by principal component analysis and factor analysis to identify the source of contamination and respective apportionment. The data clearly show that an urban-to- rural gradient exists where deposition rates are significantly higher in urban areas (up to 12325 ng/d m2 ∑PAH) compared to rural areas (as low as 11 ng/d m2 ∑PAH) and also follow seasonal trends that show higher deposition rates in the fall and winter compared to the summer and spring time. Further, based on PAH source apportionment ratios, contamination origins differ spatially. For example, fossil fuel, coal, and vehicle combustion is present in all samples; however fossil fuel combustion is dominant in urban samples. In Rural areas biomass combustion is much more prevalent and is not as greatly represented in urban or suburban areas. Therefore, even in a small state such as Rhode Island airborne PAH contamination can be fingerprinted readily for different sampling areas, indicating that distant emission sources have a widespread impact on regional air quality.

Spatial-temporal Variations and Source Apportionment of typical Heavy Metals in Beijing-Tianjin-Hebei (BTH) region of China Based on Localized Air Pollutants Emission Inventory and WRF-CMAQ modelling

NASA Astrophysics Data System (ADS)

Tian, H.; Liu, S.; Zhu, C.; Liu, H.; Wu, B.

2017-12-01

Abstract: Anthropogenic atmospheric emissions of air pollutants have caused worldwide concerns due to their adverse effects on human health and the ecosystem. By determining the best available emission factors for varied source categories, we established the comprehensive atmospheric emission inventories of hazardous air pollutants including 12 typical toxic heavy metals (Hg, As, Se, Pb, Cd, Cr, Ni, Sb, Mn, Co, Cu, and Zn) from primary anthropogenic activities in Beijing-Tianjin-Hebei (BTH) region of China for the period of 2012 for the first time. The annual emissions of these pollutants were allocated at a high spatial resolution of 9km × 9km grid with ArcGIS methodology and surrogate indexes, such as regional population and gross domestic product (GDP). Notably, the total heavy metal emissions from this region represented about 10.9% of the Chinese national total emissions. The areas with high emissions of heavy metals were mainly concentrated in Tangshan, Shijiazhuang, Handan and Tianjin. Further, WRF-CMAQ modeling system were applied to simulate the regional concentration of heavy metals to explore their spatial-temporal variations, and the source apportionment of these heavy metals in BTH region was performed using the Brute-Force method. Finally, integrated countermeasures were proposed to minimize the final air pollutants discharge on account of the current and future demand of energy-saving and pollution reduction in China. Keywords: heavy metals; particulate matter; emission inventory; CMAQ model; source apportionment Acknowledgment. This work was funded by the National Natural Science Foundation of China (21377012 and 21177012) and the Trail Special Program of Research on the Cause and Control Technology of Air Pollution under the National Key Research and Development Plan of China (2016YFC0201501).

An intensive monitoring campaign of PAHs for assessing the impact of a steel plant.

PubMed

Di Gilio, A; Ventrella, G; Giungato, P; Tutino, M; Giua, R; Assennato, G; de Gennaro, G

2017-02-01

This study provided a useful approach for assessing the impact of industrial sources on surrounding, especially in a sensitive industrial area as Taranto (South of Italy). Taranto is one of the most industrialized Italian towns, where several emission sources operate simultaneously in proximity to the urban settlement. An intensive monitoring campaign of PAHs was carried out from January 28th to July 30th, 2011, in seven sites located in residential settlement around the industrial area and in the city center. The collected data were integrated with the information about wind direction and speed by means bivariate polarplot in order to characterize and localize the industrial sources. High BaP concentrations were detected especially when Benzene to Toluene ratio (B/T ratio) values excedeed 1 and all receptor sites were downwind to the steel plant. Moreover, in order to discriminate among PAH sources and quantify their contributions, a source apportionment analysis of the collected data was provided by means Principal component Analysis (PCA) and Positive Matrix Factorization (PMF) methods. Finally, the processing of PMF5.0 output by bivariate polar plot, confirmed the impact of steel plant on both industrial sites downwind the steel plant and the city center. B[a]P apportionment was quite similar for industrial and urban sites: the traffic source contributed only 11% and 24% to B[a]P measured at two sites, respectively. Therefore, the proximity of Taranto downtown to industrial pole makes negligible all other source contributions to PAH concentrations. Copyright © 2016 Elsevier Ltd. All rights reserved.

Fugitive Dust Emissions: Development of a Real-time Monitor

DTIC Science & Technology

2011-10-01

the mechanical disturbance of soils which injects particles into the air. Common sources of FD include vehicles driving on unpaved roads...agricultural tilling, and heavy construction operations. For these sources the dust-generation process is caused by two basic physical phenomena...visibility, source apportionment , etc. The PM10 standard set by the U.S. Environmental Protection Agency in 1987 is an example of size-selective

Source Apportionment of PM2.5 using PMF and CMB: Comparison of the Effects of Transboundary and Local Pollutions in the Western Japan

NASA Astrophysics Data System (ADS)

Iijima, A.; Sugata, S.

2014-12-01

PM2.5 has become one of the most important aspects in recent air pollution issues. In Japan, the achievement rate of the environmental quality standard for PM2.5 is in a worse situation so far (43.3% for ambient air monitoring station, 33.3% for roadside air pollution monitoring station in FY2012). Therefore, source apportionment will be essential to policy and decision making for improving the PM2.5 pollution. Since 2011, we started the field monitoring study called "Current Status Elucidation and Source Contribution Assessment of PM2.5 Pollution in Collaboration with Environmental Research Institutes across Japan" which was granted by the Environment Research and Technology Development Fund (5B-1101) of the Ministry of the Environment, Japan. PM2.5 samples were collected at 14 sites during four campaigns. Chemical analyses of carbonaceous compounds, ionic species, and elements were conducted. Source apportionment was performed by using Positive Matrix Factorization (PMF, EPA PMF 3.0) and Chemical Mass Balance (CMB, EPA CMB 8.1) models. PMF model resolved a six-factor solution. Each of these factors has a distinctive grouping of species that can be associated with a specific source sector (F1: Biomass burning, F2: Sulfate + Oil combustion, F3: Industry, F4: Nitrate, F5: Sulfate + Coal combustion, and F6: Chloride). In the winter campaign (Jan. 24 to Feb. 7) in 2013, F5 accounted for 50% of total PM2.5 mass at Tsushima (34.2°N 129.3°E, the westernmost remote site). The contribution of F5 tended to decrease toward the eastern sites (27% at Fukuoka (33.5°N 130.5°E, urban site), 22% at Higashi-Osaka (34.7°N 135.6°E, urban site)). CMB model showed similar results in the same campaign. Coal combustion accounted for 49%, 30%, and 22% of total PM2.5 mass at Tsushima, Fukuoka, and Higashi-Osaka, respectively (Fig.1). On the other hand, at urban sites, higher contributions from local sources such as secondary nitrate (16% at Fukuoka, 21% at Higashi-Osaka), diesel fuel automobile (11% at Fukuoka, 12% at Higashi-Osaka), and waste incineration (7% at Fukuoka, 14% at Higashi-Osaka) were observed. This study clearly shows that the effects from the local sources are also important at the urban sites in Japan, while the impact of transboundary pollution from the Asian Continent has attracted a lot of attention in recent years.

Source apportionment of ambient volatile organic compounds in the Pearl River Delta, China: Part II

NASA Astrophysics Data System (ADS)

Liu, Ying; Shao, Min; Lu, Sihua; Chang, Chih-Chung; Wang, Jia-Lin; Fu, Linlin

The chemical mass balance receptor model was applied to the source apportionment of 58 hydrocarbons measured at seven sites in a field campaign that examined regional air quality in the Pearl River Delta (PRD) region in the fall of 2004. A total of 12 volatile organic compound (VOC) emission sources were considered, including gasoline- and diesel-powered vehicle exhausts, headspace vapors of gasoline and diesel fuel, vehicle evaporative emissions, liquid petroleum gas (LPG) leakage, paint vapors, asphalt emissions from paved roads, biomass combustion, coal combustion, the chemical industry, and petroleum refineries. Vehicle exhaust was the largest source of VOCs, contributing to >50% of ambient VOCs at the three urban sites (Guangzhou, Foshan, and Zhongshan). LPG leakage played an important role, representing 8-16% of emissions at most sites in the PRD. Solvent usage was the biggest emitter of VOCs at Dongguan, an industrial site, contributing 33% of ambient VOCs. Similarly, at Xinken, a non-urban site, the evaporation of solvents and coatings was the largest emission source, accounting for 31% of emissions, probably because it was downwind of Dongguan. Local biomass combustion was a noticeable source of VOCs at Xinken; although its contribution was estimated at 14.3%, biomass combustion was the third largest VOC source at this site.

Occurrence and source apportionment of Per- and poly-fluorinated compounds (PFCs) in North Canal Basin, Beijing

PubMed Central

Zhang, Yi-Zhe; Wang, Bin; Wang, Wei; Li, Wen-Chao; Huang, Jun; Deng, Shu-Bo; Wang, Yu-Jue; Yu, Gang

2016-01-01

Various per- and poly-fluorinated compounds (PFCs) were first systematically investigated in North Canal Basin, Beijing, China. A total of 68 surface water samples were collected from North Canal Basin, Beijing, at high spatial resolution. The seasonal disparity was compared and associated with source variation. PFCs concentrations in low-water period ranged from 26 to 207 ng/L, and significantly declined levels were found in high-water period. The individual component proportions among different sites varied less in high-water period, when runoff played a role in mixing and diluting PFCs. A methodology combined with principal component analysis (PCA), heat map-hierarchical cluster analysis (HM-HCA), and correlation analysis were introduced to discriminate sources of PFCs in surface water. The statistical results agreed with each other, and daily domestic consumption, fire-fighting products and related industries were identified as sources of PFCs in this region. In addition, two composition ratios were proposed through the methodology to distinguish the impact of nonpoint source, and the outcome demonstrates that great disparities exist in compositional profiles between nonpoint source and others. Overall, the results showed that this comprehensive analysis method has great potential for source apportionment in surface water and other environmental compartments. PMID:27845351

Source apportionment of Pb pollution in saltmarsh sediments from southwest England

NASA Astrophysics Data System (ADS)

Iurian, Andra-Rada; Millward, Geoffrey; Taylor, Alex; Marshall, William; Rodríguez, Javier; Gil Ibarguchi, José Ignacio; Blake, William H.

2017-04-01

The local availability of metal resources played a crucial role in Britain's development during the industrial revolution, but centuries of mining within Cornwall and Devon (UK) have left a legacy of contamination in river basin and estuary sediments. Improved knowledge of historical heavy metal sources, emissions and pathways will result in a better understanding of the contemporary pollution conditions and a better protection of the environment from legacy contaminants. Our study aims to trace historical sources of Pb pollution in the area of east Cornwall and west Devon, UK, using a multi proxy approach for contaminants stored in saltmarsh sediment columns from 3 systems characterized by different contamination patterns. Source apportionment investigations included the determination of Pb concentration and Pb isotopic composition (204Pb, 206Pb, 207Pb, and 208Pb) for selected down-core sediment samples, and for local ore and parent rock materials. General trends in pollutant loading (e.g. Pb) could be identified, with maximum inputs occurring in the middle of the 19th century and decreasing towards the present day, while an increase in the catchment disturbance was apparent for the last decades. The isotopic ratios of Pb further indicate that sediments with higher Pb content have a less radiogenic signature, these particular inputs being derived from Pb mining and smelting sources in the catchment area. Acknowledgements: Andra-Rada Iurian acknowledges the support of a Marie Curie Fellowship (H2020-MSCA-IF-2014, Grant Agreement number: 658863) within the Horizon 2020.

Source apportionment of aerosol particles near a steel plant by electron microscopy.

PubMed

Ebert, Martin; Müller-Ebert, Dörthe; Benker, Nathalie; Weinbruch, Stephan

2012-12-01

The size, morphology and chemical composition of 37,715 individual particles collected over 22 sampling days in the vicinity of a large integrated steel production were studied by scanning and transmission electron microscopy. Based on the morphology, chemistry and beam stability the particles were classified into the following fourteen groups: silicates, sea salt, calcium sulfates, calcium carbonates, carbonate-silicate mixtures, sulfate-silicate mixtures, iron oxides, iron mixtures, metal oxide-metals, complex secondary particles, soot, Cl-rich particles, P-rich particles, and other particles. The majority of iron oxide (≈85%) and metal oxide-metal (≈70%) particles as well as ≈20% of the silicate particles are fly ashes from high temperature processes. The emissions from the steel work are dominated by iron oxide particles. For source apportionment, seven source categories and two sectors of local wind direction (industrial and urban background) were distinguished. In both sectors PM₁₀ consists of four major source categories: 35% secondary, 20% industrial, 17% soil and 16% soot in the urban background sector compared to 45% industrial, 20% secondary, 13% soil, and 9% soot in the industrial sector. As the secondary and the soot components are higher in the urban background sector than in the industrial sector, it is concluded that both components predominantly originate from urban background sources (traffic, coal burning, and domestic heating). Abatement measures should not only focus on the steel work but should also include the urban background aerosol.

Receptor model-based source apportionment of particulate pollution in Hyderabad, India.

PubMed

Guttikunda, Sarath K; Kopakka, Ramani V; Dasari, Prasad; Gertler, Alan W

2013-07-01

Air quality in Hyderabad, India, often exceeds the national ambient air quality standards, especially for particulate matter (PM), which, in 2010, averaged 82.2 ± 24.6, 96.2 ± 12.1, and 64.3 ± 21.2 μg/m(3) of PM10, at commercial, industrial, and residential monitoring stations, respectively, exceeding the national ambient standard of 60 μg/m(3). In 2005, following an ordinance passed by the Supreme Court of India, a source apportionment study was conducted to quantify source contributions to PM pollution in Hyderabad, using the chemical mass balance (version 8.2) receptor model for 180 ambient samples collected at three stations for PM10 and PM2.5 size fractions for three seasons. The receptor modeling results indicated that the PM10 pollution is dominated by the direct vehicular exhaust and road dust (more than 60%). PM2.5 with higher propensity to enter the human respiratory tracks, has mixed sources of vehicle exhaust, industrial coal combustion, garbage burning, and secondary PM. In order to improve the air quality in the city, these findings demonstrate the need to control emissions from all known sources and particularly focus on the low-hanging fruits like road dust and waste burning, while the technological and institutional advancements in the transport and industrial sectors are bound to enhance efficiencies. Andhra Pradesh Pollution Control Board utilized these results to prepare an air pollution control action plan for the city.

Comparison of receptor models for source apportionment of the PM10 in Zaragoza (Spain).

PubMed

Callén, M S; de la Cruz, M T; López, J M; Navarro, M V; Mastral, A M

2009-08-01

Receptor models are useful to understand the chemical and physical characteristics of air pollutants by identifying their sources and by estimating contributions of each source to receptor concentrations. In this work, three receptor models based on principal component analysis with absolute principal component scores (PCA-APCS), Unmix and positive matrix factorization (PMF) were applied to study for the first time the apportionment of the airborne particulate matter less or equal than 10microm (PM10) in Zaragoza, Spain, during 1year sampling campaign (2003-2004). The PM10 samples were characterized regarding their concentrations in inorganic components: trace elements and ions and also organic components: polycyclic aromatic hydrocarbons (PAH) not only in the solid phase but also in the gas phase. A comparison of the three receptor models was carried out in order to do a more robust characterization of the PM10. The three models predicted that the major sources of PM10 in Zaragoza were related to natural sources (60%, 75% and 47%, respectively, for PCA-APCS, Unmix and PMF) although anthropogenic sources also contributed to PM10 (28%, 25% and 39%). With regard to the anthropogenic sources, while PCA and PMF allowed high discrimination in the sources identification associated with different combustion sources such as traffic and industry, fossil fuel, biomass and fuel-oil combustion, heavy traffic and evaporative emissions, the Unmix model only allowed the identification of industry and traffic emissions, evaporative emissions and heavy-duty vehicles. The three models provided good correlations between the experimental and modelled PM10 concentrations with major precision and the closest agreement between the PMF and PCA models.

Aerosol composition and source apportionment in Santiago de Chile

NASA Astrophysics Data System (ADS)

Artaxo, Paulo; Oyola, Pedro; Martinez, Roberto

1999-04-01

Santiago de Chile, São Paulo and Mexico City are Latin American urban areas that suffer from heavy air pollution. In order to study air pollution in Santiago area, an aerosol source apportionment study was designed to measure ambient aerosol composition and size distribution for two downtown sampling sites in Santiago. The aerosol monitoring stations were operated in Gotuzo and Las Condes during July and August 1996. The study employed stacked filter units (SFU) for aerosol sampling, collecting fine mode aerosol (dp<2 μm) and coarse mode aerosol (2

Source apportionment with uncertainty estimates of fine particulate matter in Ostrava, Czech Republic using Positive Matrix Factorization

EPA Science Inventory

A 14-week investigation during a warm and cold seasons was conducted to improve understanding of air pollution sources that might be impacting air quality in Ostrava, the Czech Republic. Fine particulate matter (PM2.5) samples were collected in consecutive 12-h day and night incr...

SOURCE APPORTIONMENT OF PM2.5 IN SEATTLE, WA URBAN IMPROVE SITE: COMPARISON OF THREE RECEPTOR MODELS AND SOURCE PROFILES

EPA Science Inventory

IMPROVE protocol data were collected at the urban Beacon Hill monitoring site in Seattle, WA from 1996-99. The 289 sets of PM2.5 filters were analyzed for: metals using PIXIE and XRF, anions using ion chromatography, elemental hydrogen (H) by proton scattering, and elemental an...

26 CFR 1.861-8T - Computation of taxable income from sources within the United States and from other sources and...

Code of Federal Regulations, 2013 CFR

2013-04-01

... income. In determining the method of apportionment for a specific deduction, examples of bases and..., research and development expenses, and certain other deductions. The effects on tax liability of the... comparative value of assets that generate income within each grouping, provided that such method reflects the...

26 CFR 1.861-8T - Computation of taxable income from sources within the United States and from other sources and...

Code of Federal Regulations, 2012 CFR

2012-04-01

... income. In determining the method of apportionment for a specific deduction, examples of bases and..., research and development expenses, and certain other deductions. The effects on tax liability of the... comparative value of assets that generate income within each grouping, provided that such method reflects the...

26 CFR 1.861-8T - Computation of taxable income from sources within the United States and from other sources and...

Code of Federal Regulations, 2014 CFR

2014-04-01

... income. In determining the method of apportionment for a specific deduction, examples of bases and..., research and development expenses, and certain other deductions. The effects on tax liability of the... comparative value of assets that generate income within each grouping, provided that such method reflects the...

26 CFR 1.861-8T - Computation of taxable income from sources within the United States and from other sources and...

Code of Federal Regulations, 2011 CFR

2011-04-01

... income. In determining the method of apportionment for a specific deduction, examples of bases and..., research and development expenses, and certain other deductions. The effects on tax liability of the... comparative value of assets that generate income within each grouping, provided that such method reflects the...

26 CFR 1.861-8T - Computation of taxable income from sources within the United States and from other sources and...

Code of Federal Regulations, 2010 CFR

2010-04-01

... income. In determining the method of apportionment for a specific deduction, examples of bases and..., research and development expenses, and certain other deductions. The effects on tax liability of the... comparative value of assets that generate income within each grouping, provided that such method reflects the...

Fine particulates over South Asia: Review and meta-analysis of PM2.5 source apportionment through receptor model.

PubMed

Singh, Nandita; Murari, Vishnu; Kumar, Manish; Barman, S C; Banerjee, Tirthankar

2017-04-01

Fine particulates (PM 2.5 ) constitute dominant proportion of airborne particulates and have been often associated with human health disorders, changes in regional climate, hydrological cycle and more recently to food security. Intrinsic properties of particulates are direct function of sources. This initiates the necessity of conducting a comprehensive review on PM 2.5 sources over South Asia which in turn may be valuable to develop strategies for emission control. Particulate source apportionment (SA) through receptor models is one of the existing tool to quantify contribution of particulate sources. Review of 51 SA studies were performed of which 48 (94%) were appeared within a span of 2007-2016. Almost half of SA studies (55%) were found concentrated over few typical urban stations (Delhi, Dhaka, Mumbai, Agra and Lahore). Due to lack of local particulate source profile and emission inventory, positive matrix factorization and principal component analysis (62% of studies) were the primary choices, followed by chemical mass balance (CMB, 18%). Metallic species were most regularly used as source tracers while use of organic molecular markers and gas-to-particle conversion were minimum. Among all the SA sites, vehicular emissions (mean ± sd: 37 ± 20%) emerged as most dominating PM 2.5 source followed by industrial emissions (23 ± 16%), secondary aerosols (22 ± 12%) and natural sources (20 ± 15%). Vehicular emissions (39 ± 24%) also identified as dominating source for highly polluted sites (PM 2.5 >100 μgm -3 , n = 15) while site specific influence of either or in combination of industrial, secondary aerosols and natural sources were recognized. Source specific trends were considerably varied in terms of region and seasonality. Both natural and industrial sources were most influential over Pakistan and Afghanistan while over Indo-Gangetic plain, vehicular, natural and industrial emissions appeared dominant. Influence of vehicular emission was found single dominating source over southern part while over Bangladesh, both vehicular, biomass burning and industrial sources were significant. Copyright © 2016 Elsevier Ltd. All rights reserved.

Source apportionment of PM10 and PM2.5 air pollution, and possible impacts of study characteristics in South Korea.

PubMed

Ryou, Hyoung Gon; Heo, Jongbae; Kim, Sun-Young

2018-09-01

Studies of source apportionment (SA) for particulate matter (PM) air pollution have enhanced understanding of dominant pollution sources and quantification of their contribution. Although there have been many SA studies in South Korea over the last two decades, few studies provided an integrated understanding of PM sources nationwide. The aim of this study was to summarize findings of PM SA studies of South Korea and to explore study characteristics. We selected studies that estimated sources of PM 10 and PM 2.5 performed for 2000-2017 in South Korea using Positive Matrix Factorization and Chemical Mass Balance. We reclassified the original PM sources identified in each study into seven categories: motor vehicle, secondary aerosol, soil dust, biomass/field burning, combustion/industry, natural source, and others. These seven source categories were summarized by using frequency and contribution across four regions, defined by northwest, west, southeast, and southwest regions, by PM 10 and PM 2.5 . We also computed the population-weighted mean contribution of each source category. In addition, we compared study features including sampling design, sampling and lab analysis methods, chemical components, and the inclusion of Asian dust days. In the 21 selected studies, all six PM 10 studies identified motor vehicle, soil dust, and combustion/industry, while all 15 PM 2.5 studies identified motor vehicle and soil dust. Different from the frequency, secondary aerosol produced a large contribution to both PM 10 and PM 2.5 . Motor vehicle contributed highly to both, whereas the contribution of combustion/industry was high for PM 10 . The population-weighted mean contribution was the highest for the motor vehicle and secondary aerosol sources for both PM10 and PM2.5. However, these results were based on different subsets of chemical speciation data collected at a single sampling site, commonly in metropolitan areas, with short overlap and measured by different lab analysis methods. We found that motor vehicle and secondary aerosol were the most common and influential sources for PM in South Korea. Our study, however, suggested a caution to understand SA findings from heterogeneous study features for study designs and input data. Copyright © 2018. Published by Elsevier Ltd.

Source apportionment and dynamic changes of carbonaceous aerosols during the haze bloom-decay process in China based on radiocarbon and organic molecular tracers

NASA Astrophysics Data System (ADS)

Liu, Junwen; Li, Jun; Liu, Di; Ding, Ping; Shen, Chengde; Mo, Yangzhi; Wang, Xinming; Luo, Chunling; Cheng, Zhineng; Szidat, Sönke; Zhang, Yanlin; Chen, Yingjun; Zhang, Gan

2016-03-01

Fine carbonaceous aerosols (CAs) is the key factor influencing the currently filthy air in megacities in China, yet few studies simultaneously focus on the origins of different CAs species using specific and powerful source tracers. Here, we present a detailed source apportionment for various CAs fractions, including organic carbon (OC), water-soluble OC (WSOC), water-insoluble OC (WIOC), elemental carbon (EC) and secondary OC (SOC) in the largest cities of North (Beijing, BJ) and South China (Guangzhou, GZ), using the measurements of radiocarbon and anhydrosugars. Results show that non-fossil fuel sources such as biomass burning and biogenic emission make a significant contribution to the total CAs in Chinese megacities: 56 ± 4 in BJ and 46 ± 5 % in GZ, respectively. The relative contributions of primary fossil carbon from coal and liquid petroleum combustions, primary non-fossil carbon and secondary organic carbon (SOC) to total carbon are 19, 28 and 54 % in BJ, and 40, 15 and 46 % in GZ, respectively. Non-fossil fuel sources account for 52 in BJ and 71 % in GZ of SOC, respectively. These results suggest that biomass burning has a greater influence on regional particulate air pollution in North China than in South China. We observed an unabridged haze bloom-decay process in South China, which illustrates that both primary and secondary matter from fossil sources played a key role in the blooming phase of the pollution episode, while haze phase is predominantly driven by fossil-derived secondary organic matter and nitrate.

Source apportionment and dynamic changes of carbonaceous aerosols during the haze bloom-decay process in China based on radiocarbon and organic molecular tracers

NASA Astrophysics Data System (ADS)

Liu, J.; Li, J.; Liu, D.; Ding, P.; Shen, C.; Mo, Y.; Wang, X.; Luo, C.; Cheng, Z.; Szidat, S.; Zhang, Y.; Chen, Y.; Zhang, G.

2015-12-01

Fine carbonaceous aerosols (CAs) is the key factor influencing the currently filthy air in megacities of China, yet seldom study simultaneously focuses on the origins of different CAs species using specific and powerful source tracers. Here, we present a detailed source apportionment for various CAs fractions, including organic carbon (OC), water-soluble OC (WSOC), water-insoluble OC (WIOC), elemental carbon (EC) and secondary OC (SOC) in the largest cities of North (Beijing, BJ) and South China (Guangzhou, GZ), respectively, using the measurements of radiocarbon and anhydrosugars. Results show that non-fossil fuel sources such as biomass burning and biogenic emission make a significant contribution to the total CAs in Chinese megacities: 56 ± 4 % in BJ and 46 ± 5 % in GZ, respectively. The relative contributions of primary fossil carbon from coal and liquid petroleum combustions, primary non-fossil carbon and secondary organic carbon (SOC) to total carbon are 19, 28 and 54 % in BJ, and 40, 15 and 46 % in GZ, respectively. Non-fossil fuel sources account for 52 % in BJ and 71 % in GZ of SOC, respectively. These results suggest that biomass burning has a greater influence on regional particulate air pollution in North China than in South China. We observed an unabridged haze bloom-decay process in South China, which illustrates that both primary and secondary matter from fossil sources played a key role in the blooming phase of the pollution episode, while haze phase is predominantly driven by fossil-derived secondary organic matter and nitrate.

Pollutant Source Tracking (PST) Technical Guidance

DTIC Science & Technology

2011-12-01

in the context of heavy metals (lead, copper), is considered to be a minor process contribution to the source fingerprint. 3.7 RAPID SCREENING...limits (summarized in Table 2) support the use of ICP-AES (ICP-OES) for heavy metal determination in soils , sediments, wastewater and other matrices...are included here. Isotopic ratios of stable isotopes of the metal of interest can be used for source identification and apportionment in complex

Source apportionment of carbonaceous aerosol in Sao Paulo using 13C and 14C measurements

NASA Astrophysics Data System (ADS)

Oyama, Beatriz; Andrade, Maria de Fatima; Holzinger, Rupert; Röckmann, Thomas; Meijer, Harro A. J.; Dusek, Ulrike

2016-04-01

The Metropolitan Area of Sao Paulo is affected by high aerosol concentrations, which contain a large fraction of organic material. Up to date, not much is known about the composition and origin of the organic aerosol in this city. We present the first source apportionment of the carbonaceous aerosol fraction in Sao Paulo, using stable (13C) and radioactive carbon isotopes (14C). 14C provides a clear-cut distinction between fossil sources, which contain no 14C, and contemporary sources such as biofuels, biomass burning, or biogenic sources, which contain a typical contemporary 14C/12C ratio. 13C can be used to distinguish C3 plants, such as maize and sugarcane, from C4 plants. This can help to identify a possible impact of sugarcane field burning in the rural areas of Sao Paulo State on the aerosol carbon in the city. In the first part of the study, we compare two tunnel studies: Tunnel 1 is frequented only by light duty vehicles, which run mainly on mixtures of gasoline with ethanol (gasohol, 25% ethanol and 85% gasoline) or hydrated ethanol (5% water and 95% ethanol). Tunnel 2 contains a significant fraction of heavy-duty diesel vehicles, and therefore the fraction of biofuels in the average fleet is lower. Comparison of 14C in organic and elemental carbon (OC and EC) shows that in both tunnels there is no significant contribution of biofuels to EC. Combusting ethanol-gasoline fuels in a vehicle engine does apparently not result in significant EC formation from ethanol. Biofuels contribute around 45% to OC in Tunnel 1 an only 20% in Tunnel 2, reflecting a strong impact of diesel vehicles in Tunnel 2. In the second part of the study we conduct a source apportionment of ambient aerosol carbon collected in a field study during winter (July-August) 2012. Ambient EC has two main sources, vehicular emissions and biomass burning. We estimate a contribution of vehicular sources to EC of roughly 90% during weekdays and 80% during weekends, using the 14C values measured in the tunnel studies. The absolute concentration of biomass burning EC is roughly 0.5 μg/m3 both during weekend and weekdays, whereas vehicular EC concentrations almost double during weekdays, increasing from 1.8 to 3.7 μg/m3 on average. OC concentrations are dominated by secondary carbon from vehicular emissions, both on weekdays and during weekends, however primary OC from biomass burning and contemporary secondary OC (from both biogenic and biomass burning emissions) are important fractions as well. Overall, primary biomass burning contributes between 10 and 30% to the carbonaceous aerosol in Sao Paulo. 13C measurements indicate that sugarcane burning could account for up to 15% of OC in the Sao Paulo metropolitan area.

Composition and sources of fine particulate matter across urban and rural sites in the Midwestern United States

PubMed Central

Kundu, Shuvashish; Stone, Elizabeth. A.

2014-01-01

The composition and sources of fine particulate matter (PM2.5) were investigated in rural and urban locations in Iowa, located in the agricultural and industrial Midwestern United States from April 2009 to December 2012. Major chemical contributors to PM2.5 mass were sulfate, nitrate, ammonium, and organic carbon. Non-parametric statistical analyses demonstrated that the two rural sites had significantly enhanced levels of crustal materials (Si, Al) driven by agricultural activities and unpaved roads. Meanwhile, the three urban areas had enhanced levels of secondary aerosol (nitrate, sulfate, and ammonium) and combustion (organic and elemental carbon). The heavily industrialized Davenport site had significantly higher levels of PM2.5 and trace metals (Fe, Pb, Zn), demonstrating the important local impact of industrial point sources on air quality. Sources of PM2.5 were evaluated by the multi-variant positive matrix factorization (PMF) source apportionment model. For each individual site, seven to nine factors were identified: secondary sulfate (accounting for 29–30% of PM2.5), secondary nitrate (17–24%), biomass burning (9–21%), gasoline combustion (6–16), diesel combustion (3–9%), dust (6–11%), industry (0.4–5%) and winter salt (2–6%). Source contributions demonstrated a clear urban enhancement in PM2.5 from gasoline engines (by a factor of 1.14) and diesel engines (by a factor of 2.3), which is significant due to the well-documented negative health impacts of vehicular emissions. This study presents the first source apportionment results from the state of Iowa and is broadly applicable to understanding the differences in anthropogenic and natural sources in the urban-rural continuum of particle air pollution. PMID:24736797

Data Assimilation to Improve CMAQ Model Estimates of Particulate Matter Pollution during Wintertime Persistent Cold Air Pool Events in Salt Lake City, Utah

NASA Astrophysics Data System (ADS)

Ivey, C. E.; Balachandran, S.; Russell, A. G.; Hu, Y.; Holmes, H.

2017-12-01

More than one million people live in Salt Lake Valley, Utah, where wintertime pollution reaches unhealthy levels due to the unique meteorology and orography of the region. Persistent cold air pool (PCAP) events occur when high pressure ridges create stagnant conditions over a valley, which hampers large-scale advection and reduces surface wind speeds. During PCAP periods the fraction of incoming solar radiation that reaches the valley floor is also reduced, leading to temperature inversions that allow pollution to build. Pollution levels continue to climb until a washout event removes the pollutants from the valley. Washout events include high winds or precipitation events with advection or wet deposition related removal processes, respectively. In this work, novel data assimilation and source apportionment techniques are applied for January and February 2007 to analyze CMAQ-modeled source composition and source impacts for the Salt Lake Valley during PCAP events. First, a hybrid source-oriented apportionment model is applied over continental U.S. to determine observation and model-based impacts from 20 sources, including agricultural activities, fossil fuel combustion, dust, and metals processing. Then, a secondary bias correction method is applied to better quantify the source impacts on secondary PM2.5, which constitutes the majority of the PM2.5 mass. Revised concentrations reflect what was previously reported in studies of PCAP pollution in the Salt Lake Valley, where the dominant aerosol was found to be ammonium nitrate. Further, gasoline and natural gas combustion were found to be the greatest contributing sources to aerosol concentrations during the PCAP events. The benefit of the data assimilation methods is the availability of spatially and temporally resolved model estimates of source impacts that better reflect observed concentrations.

Chemical speciation and source apportionment of Non-Methane Volatile Organic Compounds (NMVOCs) in a Middle Eastern country

NASA Astrophysics Data System (ADS)

Salameh, Therese; Sauvage, Stéphane; Afif, Charbel; Borbon, Agnès; Locoge, Nadine

2014-05-01

NMVOCs, emitted from various sources, are of particular interest since they contribute to the formation of tropospheric ozone, PAN and secondary organic aerosols resulting in negative impacts on human health, climate and on the environment. To identify abatement measures, a profound knowledge of emission sources and their composition is a prerequisite. Air pollution in the Middle East region remains difficult to assess and understand because of a lack of ground-based measurements and the limited information on NMVOC chemical speciation and source apportionment. Based on a large database of NMVOC observations obtained in Beirut, the capital of Lebanon (a developing country in the Middle East region, located in Western Asia on the eastern shore of the Mediterranean Sea), the overall objective of this work is to apportion the sources of NMVOCs encountered in Lebanon. First, source profiles were determined with field measurements close to the main potential emitters namely the road transport, gasoline vapour, power generation and solvent uses. The results obtained are compared to other studies held in other regions and are used to assess the emission inventory developed for Lebanon. Secondly, two intensive field campaigns were held in a receptor site in Beirut during summer 2011 and winter 2012 in order to obtain a large time resolved dataset. The PMF analysis of this dataset was applied to apportion anthropogenic sources in this area. In both seasons, combustion (road transport and power generation) and gasoline evaporation, especially in winter, were the main sources contributing to the NMVOCs in Beirut. The results will support model implementation especially by completing the emission inventory established for the year 2010 by Waked et al. 2012 according to the EEA/EMEP guidelines because of the lack of Lebanon-specific emission factor.

Mass spectra features of biomass burning boiler and coal burning boiler emitted particles by single particle aerosol mass spectrometer.

PubMed

Xu, Jiao; Li, Mei; Shi, Guoliang; Wang, Haiting; Ma, Xian; Wu, Jianhui; Shi, Xurong; Feng, Yinchang

2017-11-15

In this study, single particle mass spectra signatures of both coal burning boiler and biomass burning boiler emitted particles were studied. Particle samples were suspended in clean Resuspension Chamber, and analyzed by ELPI and SPAMS simultaneously. The size distribution of BBB (biomass burning boiler sample) and CBB (coal burning boiler sample) are different, as BBB peaks at smaller size, and CBB peaks at larger size. Mass spectra signatures of two samples were studied by analyzing the average mass spectrum of each particle cluster extracted by ART-2a in different size ranges. In conclusion, BBB sample mostly consists of OC and EC containing particles, and a small fraction of K-rich particles in the size range of 0.2-0.5μm. In 0.5-1.0μm, BBB sample consists of EC, OC, K-rich and Al_Silicate containing particles; CBB sample consists of EC, ECOC containing particles, while Al_Silicate (including Al_Ca_Ti_Silicate, Al_Ti_Silicate, Al_Silicate) containing particles got higher fractions as size increase. The similarity of single particle mass spectrum signatures between two samples were studied by analyzing the dot product, results indicated that part of the single particle mass spectra of two samples in the same size range are similar, which bring challenge to the future source apportionment activity by using single particle aerosol mass spectrometer. Results of this study will provide physicochemical information of important sources which contribute to particle pollution, and will support source apportionment activities. Copyright © 2017. Published by Elsevier B.V.

Daily trends and source apportionment of ultrafine particulate mass (PM0.1) over an annual cycle in a typical California city.

PubMed

Kuwayama, Toshihiro; Ruehl, Chris R; Kleeman, Michael J

2013-12-17

Toxicology studies indicate that inhalation of ultrafine particles (Dp < 0.1 μm) causes adverse health effects, presumably due to their large surface area-to-volume ratio that can drive heterogeneous reactions. Epidemiological associations between ultrafine particles and health effects, however, have been difficult to identify due to the lack of appropriate long-term monitoring and exposure data. The majority of the existing ultrafine particle epidemiology studies are based on exposure to particle number, although an independent analysis suggests that ultrafine particle mass (PM0.1) correlates better with particle surface area. More information is needed to characterize PM0.1 exposure to fully evaluate the health effects of ultrafine particles using epidemiology. The present study summarizes 1 year of daily PM0.1 chemistry and source apportionment at Sacramento, CA, USA. Positive matrix factorization (PMF) was used to resolve PM0.1 source contributions from old-technology diesel engines, residential wood burning, rail, regional traffic, and brake wear/road dust. Diesel PM0.1 and total PM0.1 concentrations were reduced by 97 and 26%, respectively, as a result of the adoption of cleaner diesel technology. The strong linear correlation between PM0.1 and particle surface area in central California suggests that the adoption of clean diesel engines reduced particle surface area by similar amounts. PM0.1 sulfate reduction occurred as a result of reduced primary particle surface area available for sulfate condensation. The current study demonstrates the capability of measuring PM0.1 source contributions over a 12 month period and identifies the extended benefits of emissions reduction efforts for diesel engines on ambient concentrations of primary and secondary PM0.1.

Risk profile and health vulnerability of female workers who pick cotton by organanochlorine pesticides from southern Punjab, Pakistan.

PubMed

Yasmeen, Humaira; Qadir, Abdul; Mumtaz, Mehvish; Eqani, Syed Ali Musstjab Akber Shah; Syed, Jabbir Hussain; Mahmood, Adeel; Jamil, Nadia; Nazar, Farva; Ali, Habib; Ahmad, Muhammad Shafiq; Tanveer, Zafar Iqbal; Zhang, Gan

2017-05-01

The present study was conducted to highlight the existing level of organochlorine-pesticides (OCPs) from human milk (n = 45) and blood serum (n = 40) of female workers who pick cotton in Khanewal District, southern Punjab, Pakistan. Source apportionment, congener-specific analysis, and risk surveillance of OCPs are reported from human milk and blood samples. Levels of OCPs in milk and blood serum samples ranged from 15.7 ppb to 538.3 ppb and from 16.4 ppb to 747.1 ppb, respectively, and were lower than previously published reports from other regions of the globe. Congener-specific analysis revealed that DDTs were predominant, followed by hexachlorocyclohexane, chlordane, and hexachlorobenzene. Calculated results for source apportionment analysis suggested that contamination load was a new input of DDTs as well as the historic use of lindane in the study area. Levels of OCPs in milk and blood serum were significantly (p < 0.05) correlated with age, time period of picking cotton, and number of children. Health risk revealed that female workers had risk of cancer among 1 per million; however, noncarcinogenic risks were not considerable. Environ Toxicol Chem 2017;36:1193-1201. © 2016 SETAC. © 2016 SETAC.

A stable isotope approach for source apportionment of chlorinated ethene plumes at a complex multi-contamination events urban site

NASA Astrophysics Data System (ADS)

Nijenhuis, Ivonne; Schmidt, Marie; Pellegatti, Eleonora; Paramatti, Enrico; Richnow, Hans Hermann; Gargini, Alessandro

2013-10-01

The stable carbon isotope composition of chlorinated aliphatic compounds such as chlorinated methanes, ethanes and ethenes was examined as an intrinsic fingerprint for apportionment of sources. A complex field site located in Ferrara (Italy), with more than 50 years history of use of chlorinated aliphatic compounds, was investigated in order to assess contamination sources. Several contamination plumes were found in a complex alluvial sandy multi-aquifer system close to the river Po; sources are represented by uncontained former industrial and municipal dump sites as well as by spills at industrial areas. The carbon stable isotope signature allowed distinguishing 2 major sources of contaminants. One source of chlorinated aliphatic contaminants was strongly depleted in 13C (<-60‰) suggesting production lines which have used depleted methane for synthesis. The other source had typical carbon isotope compositions of >-40‰ which is commonly observed in recent production of chlorinated solvents. The degradation processes in the plumes could be traced interpreting the isotope enrichment and depletion of parent and daughter compounds, respectively. We demonstrate that, under specific production conditions, namely when highly chlorinated ethenes are produced as by-product during chloromethanes production, 13C depleted fingerprinting of contaminants can be obtained and this can be used to track sources and address the responsible party of the pollution in urban areas.

Sources and elemental composition of ambient PM(2.5) in three European cities.

PubMed

Vallius, M; Janssen, N A H; Heinrich, J; Hoek, G; Ruuskanen, J; Cyrys, J; Van Grieken, R; de Hartog, J J; Kreyling, W G; Pekkanen, J

2005-01-20

Source apportionment of urban fine particle mass (PM(2.5)) was performed from data collected during 1998-1999 in Amsterdam (The Netherlands), Erfurt (Germany) and Helsinki (Finland), using principal component analysis (PCA) and multiple linear regression. Six source categories of PM(2.5) were identified in Amsterdam. They were traffic-related particles (30% of the average PM(2.5)), secondary particles (34%), crustal material (7%), oil combustion (11%), industrial and incineration processes (9%), and sea salt (2%). The unidentified PM(2.5) fraction was 7% on the average. In Erfurt, four source categories were extracted with some difficulties in interpretation of source profiles. They were combustion emissions related to traffic (32%), secondary PM (32%), crustal material (21%) and industrial processes (8%). In Erfurt, 3% of PM(2.5) remained unidentified. Air pollution data and source apportionment results from the two Central European cities were compared to previously published results from Helsinki, where about 80% of average PM(2.5) was attributed to transboundary air pollution and particles from traffic and other regional combustion sources. Our results indicate that secondary particles and local combustion processes (mainly traffic) were the most important source categories in all cities; their impact on the average PM(2.5) was almost equal in Amsterdam and Erfurt whereas, in Helsinki, secondary particles made up for as much as half of the total average PM(2.5).

A stable isotope approach for source apportionment of chlorinated ethene plumes at a complex multi-contamination events urban site.

PubMed

Nijenhuis, Ivonne; Schmidt, Marie; Pellegatti, Eleonora; Paramatti, Enrico; Richnow, Hans Hermann; Gargini, Alessandro

2013-10-01

The stable carbon isotope composition of chlorinated aliphatic compounds such as chlorinated methanes, ethanes and ethenes was examined as an intrinsic fingerprint for apportionment of sources. A complex field site located in Ferrara (Italy), with more than 50years history of use of chlorinated aliphatic compounds, was investigated in order to assess contamination sources. Several contamination plumes were found in a complex alluvial sandy multi-aquifer system close to the river Po; sources are represented by uncontained former industrial and municipal dump sites as well as by spills at industrial areas. The carbon stable isotope signature allowed distinguishing 2 major sources of contaminants. One source of chlorinated aliphatic contaminants was strongly depleted in ¹³C (<-60‰) suggesting production lines which have used depleted methane for synthesis. The other source had typical carbon isotope compositions of >-40‰ which is commonly observed in recent production of chlorinated solvents. The degradation processes in the plumes could be traced interpreting the isotope enrichment and depletion of parent and daughter compounds, respectively. We demonstrate that, under specific production conditions, namely when highly chlorinated ethenes are produced as by-product during chloromethanes production, ¹³C depleted fingerprinting of contaminants can be obtained and this can be used to track sources and address the responsible party of the pollution in urban areas. © 2013 Elsevier B.V. All rights reserved.

Part 2. Development of Enhanced Statistical Methods for Assessing Health Effects Associated with an Unknown Number of Major Sources of Multiple Air Pollutants.

PubMed

Park, Eun Sug; Symanski, Elaine; Han, Daikwon; Spiegelman, Clifford

2015-06-01

A major difficulty with assessing source-specific health effects is that source-specific exposures cannot be measured directly; rather, they need to be estimated by a source-apportionment method such as multivariate receptor modeling. The uncertainty in source apportionment (uncertainty in source-specific exposure estimates and model uncertainty due to the unknown number of sources and identifiability conditions) has been largely ignored in previous studies. Also, spatial dependence of multipollutant data collected from multiple monitoring sites has not yet been incorporated into multivariate receptor modeling. The objectives of this project are (1) to develop a multipollutant approach that incorporates both sources of uncertainty in source-apportionment into the assessment of source-specific health effects and (2) to develop enhanced multivariate receptor models that can account for spatial correlations in the multipollutant data collected from multiple sites. We employed a Bayesian hierarchical modeling framework consisting of multivariate receptor models, health-effects models, and a hierarchical model on latent source contributions. For the health model, we focused on the time-series design in this project. Each combination of number of sources and identifiability conditions (additional constraints on model parameters) defines a different model. We built a set of plausible models with extensive exploratory data analyses and with information from previous studies, and then computed posterior model probability to estimate model uncertainty. Parameter estimation and model uncertainty estimation were implemented simultaneously by Markov chain Monte Carlo (MCMC*) methods. We validated the methods using simulated data. We illustrated the methods using PM2.5 (particulate matter ≤ 2.5 μm in aerodynamic diameter) speciation data and mortality data from Phoenix, Arizona, and Houston, Texas. The Phoenix data included counts of cardiovascular deaths and daily PM2.5 speciation data from 1995-1997. The Houston data included respiratory mortality data and 24-hour PM2.5 speciation data sampled every six days from a region near the Houston Ship Channel in years 2002-2005. We also developed a Bayesian spatial multivariate receptor modeling approach that, while simultaneously dealing with the unknown number of sources and identifiability conditions, incorporated spatial correlations in the multipollutant data collected from multiple sites into the estimation of source profiles and contributions based on the discrete process convolution model for multivariate spatial processes. This new modeling approach was applied to 24-hour ambient air concentrations of 17 volatile organic compounds (VOCs) measured at nine monitoring sites in Harris County, Texas, during years 2000 to 2005. Simulation results indicated that our methods were accurate in identifying the true model and estimated parameters were close to the true values. The results from our methods agreed in general with previous studies on the source apportionment of the Phoenix data in terms of estimated source profiles and contributions. However, we had a greater number of statistically insignificant findings, which was likely a natural consequence of incorporating uncertainty in the estimated source contributions into the health-effects parameter estimation. For the Houston data, a model with five sources (that seemed to be Sulfate-Rich Secondary Aerosol, Motor Vehicles, Industrial Combustion, Soil/Crustal Matter, and Sea Salt) showed the highest posterior model probability among the candidate models considered when fitted simultaneously to the PM2.5 and mortality data. There was a statistically significant positive association between respiratory mortality and same-day PM2.5 concentrations attributed to one of the sources (probably industrial combustion). The Bayesian spatial multivariate receptor modeling approach applied to the VOC data led to a highest posterior model probability for a model with five sources (that seemed to be refinery, petrochemical production, gasoline evaporation, natural gas, and vehicular exhaust) among several candidate models, with the number of sources varying between three and seven and with different identifiability conditions. Our multipollutant approach assessing source-specific health effects is more advantageous than a single-pollutant approach in that it can estimate total health effects from multiple pollutants and can also identify emission sources that are responsible for adverse health effects. Our Bayesian approach can incorporate not only uncertainty in the estimated source contributions, but also model uncertainty that has not been addressed in previous studies on assessing source-specific health effects. The new Bayesian spatial multivariate receptor modeling approach enables predictions of source contributions at unmonitored sites, minimizing exposure misclassification and providing improved exposure estimates along with their uncertainty estimates, as well as accounting for uncertainty in the number of sources and identifiability conditions.

A combined approach for the evaluation of a volatile organic compound emissions inventory.

PubMed

Choi, Yu-Jin; Calabrese, Richard V; Ehrman, Sheryl H; Dickerson, Russell R; Stehr, Jeffrey W

2006-02-01

Emissions inventories significantly affect photochemical air quality model performance and the development of effective control strategies. However, there have been very few studies to evaluate their accuracy. Here, to evaluate a volatile organic compound (VOC) emissions inventory, we implemented a combined approach: comparing the ratios of carbon bond (CB)-IV VOC groups to nitrogen oxides (NOx) or carbon monoxide (CO) using an emission preprocessing model, comparing the ratios of VOC source contributions from a source apportionment technique to NOx or CO, and comparing ratios of CB-IV VOC groups to NOx or CO and the absolute concentrations of CB-IV VOC groups using an air quality model, with the corresponding ratios and concentrations observed at three sites (Maryland, Washington, DC, and New Jersey). The comparisons of the ethene/NOx ratio, the xylene group (XYL)/NOx ratio, and ethene and XYL concentrations between estimates and measurements showed some differences, depending on the comparison approach, at the Maryland and Washington, DC sites. On the other hand, consistent results at the New Jersey site were observed, implying a possible overestimation of vehicle exhaust. However, in the case of the toluene group (TOL), which is emitted mainly from surface coating and printing sources in the solvent utilization category, the ratios of TOL/ NOx or CO, as well as the absolute concentrations revealed an overestimate of these solvent sources by a factor of 1.5 to 3 at all three sites. In addition, the overestimate of these solvent sources agreed with the comparisons of surface coating and printing source contributions relative to NOx from a source apportionment technique to the corresponding value of estimates at the Maryland site. Other studies have also suggested an overestimate of solvent sources, implying a possibility of inaccurate emission factors in estimating VOC emissions from surface coating and printing sources. We tested the impact of these overestimates with a chemical transport model and found little change in ozone but substantial changes in calculated secondary organic aerosol concentrations.

Biomass burning in the Amazon region: Aerosol source apportionment and associated health risk assessment

NASA Astrophysics Data System (ADS)

de Oliveira Alves, Nilmara; Brito, Joel; Caumo, Sofia; Arana, Andrea; de Souza Hacon, Sandra; Artaxo, Paulo; Hillamo, Risto; Teinilä, Kimmo; Batistuzzo de Medeiros, Silvia Regina; de Castro Vasconcellos, Pérola

2015-11-01

The Brazilian Amazon represents about 40% of the world's remaining tropical rainforest. However, human activities have become important drivers of disturbance in that region. The majority of forest fire hotspots in the Amazon arc due to deforestation are impacting the health of the local population of over 10 million inhabitants. In this study we characterize western Amazonia biomass burning emissions through the quantification of 14 Polycyclic Aromatic Hydrocarbons (PAHs), Organic Carbon, Elemental Carbon and unique tracers of biomass burning such as levoglucosan. From the PAHs dataset a toxic equivalence factor is calculated estimating the carcinogenic and mutagenic potential of biomass burning emissions during the studied period. Peak concentration of PM10 during the dry seasons was observed to reach 60 μg m-3 on the 24 h average. Conversely, PM10 was relatively constant throughout the wet season indicating an overall stable balance between aerosol sources and sinks within the filter sampling resolution. Similar behavior is identified for OC and EC components. Levoglucosan was found in significant concentrations (up to 4 μg m-3) during the dry season. Correspondingly, the estimated lung cancer risk calculated during the dry seasons largely exceeded the WHO health-based guideline. A source apportionment study was carried out through the use of Absolute Principal Factor Analysis (APFA), identifying a three-factor solution. The biomass burning factor is found to be the dominating aerosol source, having 75.4% of PM10 loading. The second factor depicts an important contribution of several PAHs without a single source class and therefore was considered as mixed sources factor, contributing to 6.3% of PM10. The third factor was mainly associated with fossil fuel combustion emissions, contributing to 18.4% of PM10. This work enhances the knowledge of aerosol sources and its impact on climate variability and local population, on a site representative of the deforestation which occupies a significant fraction of the Amazon basin.

Water quality assessment and apportionment of pollution sources using APCS-MLR and PMF receptor modeling techniques in three major rivers of South Florida.

PubMed

Haji Gholizadeh, Mohammad; Melesse, Assefa M; Reddi, Lakshmi

2016-10-01

In this study, principal component analysis (PCA), factor analysis (FA), and the absolute principal component score-multiple linear regression (APCS-MLR) receptor modeling technique were used to assess the water quality and identify and quantify the potential pollution sources affecting the water quality of three major rivers of South Florida. For this purpose, 15years (2000-2014) dataset of 12 water quality variables covering 16 monitoring stations, and approximately 35,000 observations was used. The PCA/FA method identified five and four potential pollution sources in wet and dry seasons, respectively, and the effective mechanisms, rules and causes were explained. The APCS-MLR apportioned their contributions to each water quality variable. Results showed that the point source pollution discharges from anthropogenic factors due to the discharge of agriculture waste and domestic and industrial wastewater were the major sources of river water contamination. Also, the studied variables were categorized into three groups of nutrients (total kjeldahl nitrogen, total phosphorus, total phosphate, and ammonia-N), water murkiness conducive parameters (total suspended solids, turbidity, and chlorophyll-a), and salt ions (magnesium, chloride, and sodium), and average contributions of different potential pollution sources to these categories were considered separately. The data matrix was also subjected to PMF receptor model using the EPA PMF-5.0 program and the two-way model described was performed for the PMF analyses. Comparison of the obtained results of PMF and APCS-MLR models showed that there were some significant differences in estimated contribution for each potential pollution source, especially in the wet season. Eventually, it was concluded that the APCS-MLR receptor modeling approach appears to be more physically plausible for the current study. It is believed that the results of apportionment could be very useful to the local authorities for the control and management of pollution and better protection of important riverine water quality. Copyright © 2016 Elsevier B.V. All rights reserved.

76 FR 8811 - FTA Fiscal Year 2011 Apportionments, Allocations and Program Information: Corrections

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-15

... Apportionments) and Table 10 (Prior Year Unobligated Section 5309 Bus and Bus Related Equipment and Facilities... DEPARTMENT OF TRANSPORTATION Federal Transit Administration FTA Fiscal Year 2011 Apportionments... titled ``FTA Fiscal Year 2011 Apportionments, Allocations and Program Information.'' FOR FURTHER...

Illuminating the Shadows of War: Demystifying Complex Adaptive Systems

DTIC Science & Technology

2009-06-01

time for reviewing instructions, searching existing data sources , gathering and maintaining the data needed, and completing and reviewing the...resources required when confronting an adversary such as Hezbollah. Apportionment of time, effort, and resources to influence 2 Hezbollah’s...Figure 1: Clausewitz’s Paradoxical Trinity Source : Author’s original work Nearly a century later, British Army officer, military

Use of Lead Isotopes to Identify Sources of Metal and Metalloid Contaminants in Atmospheric Aerosol from Mining Operations

PubMed Central

Félix, Omar I.; Csavina, Janae; Field, Jason; Rine, Kyle P.; Sáez, A. Eduardo; Betterton, Eric A.

2014-01-01

Mining operations are a potential source of metal and metalloid contamination by atmospheric particulate generated from smelting activities, as well as from erosion of mine tailings. In this work, we show how lead isotopes can be used for source apportionment of metal and metalloid contaminants from the site of an active copper mine. Analysis of atmospheric aerosol shows two distinct isotopic signatures: one prevalent in fine particles (< 1 μm aerodynamic diameter) while the other corresponds to coarse particles as well as particles in all size ranges from a nearby urban environment. The lead isotopic ratios found in the fine particles are equal to those of the mine that provides the ore to the smelter. Topsoil samples at the mining site show concentrations of Pb and As decreasing with distance from the smelter. Isotopic ratios for the sample closest to the smelter (650 m) and from topsoil at all sample locations, extending to more than 1 km from the smelter, were similar to those found in fine particles in atmospheric dust. The results validate the use of lead isotope signatures for source apportionment of metal and metalloid contaminants transported by atmospheric particulate. PMID:25496740

Source Apportionment of Atmospheric Polychlorinated Biphenyls in New Jersey 1997-2011.

PubMed

Praipipat, Pornsawai; Meng, Qingyu; Miskewitz, Robert J; Rodenburg, Lisa A

2017-02-07

Concentrations of polychlorinated biphenyls (PCBs) in the Delaware River currently exceed the Water Quality Criteria of 16 pg/L for the sum of PCBs due in part to atmospheric deposition. The purpose of this work was to use a source apportionment tool called Positive Matrix Factorization (PMF) to identify the sources of PCBs to the atmosphere in this area and determine whether their concentrations are declining over time. The data set was compiled by the Delaware Atmospheric Deposition Network (DADN) from samples taken in Camden, NJ from 1999 to 2011 and New Brunswick, NJ from 1997 to 2011. The PMF analysis revealed four resolved factors at each site. The factors that dominate the PCB burden in the atmosphere at both Camden and New Brunswick resemble Aroclor 1242. These factors declined in concentration during some portions of the monitoring period, but this decline slowed or stopped during 2003-2011. None of the factors displayed consistent declines in concentration throughout the monitoring periods, and some factors actually increased in concentration during some periods. This suggests natural attenuation alone will not control atmospheric PCB concentrations, and additional efforts are needed to control PCB atmospheric emissions as well as the numerous other sources of PCBs to the estuary.

Speciation of organic fractions does matter for aerosol source apportionment. Part 2: Intensive short-term campaign in the Paris area (France).

PubMed

Srivastava, D; Favez, O; Bonnaire, N; Lucarelli, F; Haeffelin, M; Perraudin, E; Gros, V; Villenave, E; Albinet, A

2018-09-01

The present study aimed at performing PM 10 source apportionment, using positive matrix factorization (PMF), based on filter samples collected every 4h at a sub-urban station in the Paris region (France) during a PM pollution event in March 2015 (PM 10 >50μgm -3 for several consecutive days). The PMF model allowed to deconvolve 11 source factors. The use of specific primary and secondary organic molecular markers favoured the determination of common sources such as biomass burning and primary traffic emissions, as well as 2 specific biogenic SOA (marine+isoprene) and 3 anthropogenic SOA (nitro-PAHs+oxy-PAHs+phenolic compounds oxidation) factors. This study is probably the first one to report the use of methylnitrocatechol isomers as well as 1-nitropyrene to apportion secondary OA linked to biomass burning emissions and primary traffic emissions, respectively. Secondary organic carbon (SOC) fractions were found to account for 47% of the total OC. The use of organic molecular markers allowed the identification of 41% of the total SOC composed of anthropogenic SOA (namely, oxy-PAHs, nitro-PAHs and phenolic compounds oxidation, representing 15%, 9%, 11% of the total OC, respectively) and biogenic SOA (marine+isoprene) (6% in total). Results obtained also showed that 35% of the total SOC originated from anthropogenic sources and especially PAH SOA (oxy-PAHs+nitro-PAHs), accounting for 24% of the total SOC, highlighting its significant contribution in urban influenced environments. Anthropogenic SOA related to nitro-PAHs and phenolic compounds exhibited a clear diurnal pattern with high concentrations during the night indicating the prominent role of night-time chemistry but with different chemical processes involved. Copyright © 2018 Elsevier B.V. All rights reserved.

Lorain Harbor, Ohio. Preliminary Feasibility Study (Stage 2). Review of Reports. Volume 1. Main Report.

DTIC Science & Technology

1980-10-01

May 1980 Dollars) 93 32 Apportionment of Total Project Cost for Alternative 1, Option 1 (1,000-Footer) 94 33 Estimated Investment Cost and Annual...Costs - Alternative 2, Option 1 (1,000-Foot Vessels) (May 1980 Dollars) 101 36 Apportionment of Total Project Cost for Alternative 2, Option 1 (1,000...1 (1,000-Footer) 104 39 Estimate of Navigation Project Codes - Alternative 3, Option 1 (1,000-Foot Vessels) (May 1980 Dollars) 107 40 Apportionment of

Study on Sources of Volatile Organic Compounds (CMB) in Pearl River Delta region, China

NASA Astrophysics Data System (ADS)

Liu, Y.; Shao, M.; Lu, S.; Chang, C.; Wang, C. J.; Wang, B.

2007-05-01

The profiles of major Volatile organic compounds (VOCs) sources including vehicle exhaust, gasoline vapor, painting, asphalt, liquefied petroleum gas (LPG), biomass burning and petrochemical industry in Pearl River Delta were experimentally determined. Source samples were taken by using dilution chamber for mobile and stationary sources, laboratory simulation for biomass burning. The concentrations of 108 VOC species of sources were quantified by using canister with pre-concentration-GC/MS system, from which 52 PAMS hydrocarbons and one kind of chlorinated hydrocarbon were deployed to build the source profiles for source apportionment of VOCs. Based the measurement of source profiles, the possible tracers for various emission sources were identified, e.g 2-methylbutane and 1,3-butadiene were the tracers for motor vehicle exhaust, the characteristic compounds of architectural and furnishing coatings are aromatics such as toluene and m/p-xylene; the light hydrocarbons, namely n-butane, trans-2-butene and n-pentane, dominated the composition of gasoline vapor; and the nonane, decane and undecane are found to represent the asphalt emissions etc.. The CMB receptor model was applied to source apportionment of 58 hydrocarbons measured at seven sites during the PRD campaign, 2004. The 12 kinds of VOC sources include gasoline/diesel-powered vehicle exhaust, gasoline/diesel headspace vapor, vehicle evaporative emissions, liquid petroleum gas (LPG) leakage, painting vapors, asphalt emission from paved road, biomass burning, coal burning, chemical industry and petroleum refinery. Vehicle exhaust was the largest sources contributing over half of the ambient VOCs at the three urban sites (GuangZhou, FoShan and ZhongShan). LPG leakage played an important role with the percentage of 8- 16% in most sites in PRD. Contributions from solvents usage were highest at DongGuan, an industrial site. At XinKen, the solvents and coatings had the largest percentage of 31% probably due to the influence of its upwind area of DongGuan. The local biomass burning was also found to be a noticeable source at XK.

Navy Littoral Combat Ship (LCS) Program: Background, Issues, and Options for Congress

DTIC Science & Technology

2011-01-20

response, including the time for reviewing instructions, searching existing data sources , gathering and maintaining the data needed, and completing and...Congressional Research Service 3 Figure 1. Lockheed LCS Design (Top) and General Dynamics LCS Design (Bottom) Source : Source : U.S. Navy file photo...according to an agreed apportionment (i.e., a “share line”). Any cost growth above the ceiling cost would be borne entirely by the contractor. The Navy

Quantitative identification and source apportionment of anthropogenic heavy metals in marine sediment of Hong Kong

NASA Astrophysics Data System (ADS)

Zhou, Feng; Guo, Huaicheng; Liu, Lei

2007-10-01

Based on ten heavy metals collected twice annually at 59 sites from 1998 to 2004, enrichment factors (EFs), principal component analysis (PCA) and multivariate linear regression of absolute principal component scores (MLR-APCS) were used in identification and source apportionment of the anthropogenic heavy metals in marine sediment. EFs with Fe as a normalizer and local background as reference values was properly tested and suitable in Hong Kong, and Zn, Ni, Pb, Cu, Cd, Hg and Cr mainly originated from anthropogenic sources, while Al, Mn and Fe were derived from rocks weathering. Rotated PCA and GIS mapping further identified two types of anthropogenic sources and their impacted regions: (1) electronic industrial pollution, riparian runoff and vehicle exhaust impacted the entire Victoria Harbour, inner Tolo Harbour, Eastern Buffer, inner Deep Bay and Cheung Chau; and (2) discharges from textile factories and paint, influenced Tsuen Wan Bay and Kwun Tong typhoon shelter and Rambler Channel. In addition, MLR-APCS was successfully introduced to quantitatively determine the source contributions with uncertainties almost less than 8%: the first anthropogenic sources were responsible for 50.0, 45.1, 86.6, 78.9 and 87.5% of the Zn, Pb, Cu, Cd and Hg, respectively, whereas 49.9% of the Ni and 58.4% of the Cr came from the second anthropogenic sources.

Chemical Composition and Source Apportionment of Size ...

EPA Pesticide Factsheets

The Cleveland airshed comprises a complex mixture of industrial source emissions that contribute to periods of non-attainment for fine particulate matter (PM 2.5 ) and are associated with increased adverse health outcomes in the exposed population. Specific PM sources responsible for health effects however are not fully understood. Size-fractionated PM (coarse, fine, and ultrafine) samples were collected using a ChemVol sampler at an urban site (G.T. Craig (GTC)) and rural site (Chippewa Lake (CLM)) from July 2009 to June 2010, and then chemically analyzed. The resulting speciated PM data were apportioned by EPA positive matrix factorization to identify emission sources for each size fraction and location. For comparisons with the ChemVol results, PM samples were also collected with sequential dichotomous and passive samplers, and evaluated for source contributions to each sampling site. The ChemVol results showed that annual average concentrations of PM, elemental carbon, and inorganic elements in the coarse fraction at GTC were ~ 2, ~7, and ~3 times higher than those at CLM, respectively, while the smaller size fractions at both sites showed similar annual average concentrat ions. Seasonal variations of secondary aerosols (e.g., high N03- level in winter and high SO42- level in summer) were observed at both sites. Source apportionment results demonstrated that the PM samples at GTC and CLM were enriched with local industrial sources (e.g., steel plant and coa

Comparative study of volatile organic compounds in ambient air using observed mixing ratios and initial mixing ratios taking chemical loss into account - A case study in a typical urban area in Beijing.

PubMed

Gao, Jian; Zhang, Jie; Li, Hong; Li, Lei; Xu, Linghong; Zhang, Yujie; Wang, Zhanshan; Wang, Xuezhong; Zhang, Weiqi; Chen, Yizhen; Cheng, Xi; Zhang, Hao; Peng, Liang; Chai, Fahe; Wei, Yongjie

2018-07-01

Volatile organic compounds (VOCs) can react with atmospheric radicals while being transported after being emitted, resulting in substantial losses. Using only observed VOC mixing ratios to assess VOC pollution, is therefore problematic. The observed mixing ratios and initial mixing ratios taking chemical loss into consideration were performed using data for 90 VOCs in the atmosphere in a typical urban area in Beijing in winter 2013 to gain a more accurate view of VOC pollution. The VOC sources, ambient VOC mixing ratios and compositions, variability and influencing factors, contributions to near-ground-ozone and health risks posed were assessed. Source apportionment should be conducted using initial mixing ratios, but health risks should be assessed using observed mixing ratios. The daytime daily mean initial mixing ratio (72.62ppbv) was 7.72ppbv higher than the daytime daily mean observed mixing ratio (64.90ppbv). Alkenes contributed >70% of the consumed VOCs. The nighttime daily mean observed mixing ratio was 71.66ppbv, 6.76ppbv higher than the daytime mixing ratio. The observed mixing ratio for 66 VOCs was 40.31% higher in Beijing than New York. The OFPs of Ini-D (266.54ppbv) was underestimated 23.41% compared to the OFP of Obs-D (204.14ppbv), improving emission control of ethylene and propene would be an effective way of controlling O 3 . Health risk assessments performed for 28 hazardous VOCs show that benzene, chloroform, 1,2-dichloroethane, and acetaldehyde pose carcinogenic risk and acrolein poses non-carcinogenic risks. Source apportionment results indicated that vehicle exhausts, solvent usage and industrial processes were the main VOC source during the study. Copyright © 2018. Published by Elsevier B.V.

Source Apportionment of Suspended Sediment Sources using 137Cs and 210Pbxs

NASA Astrophysics Data System (ADS)

Lamba, J.; Karthikeyan, K.; Thompson, A.

2017-12-01

A study was conducted in the Pleasant Valley Watershed (50 km 2) in South Central Wisconsin to better understand sediment transport processes using sediment fingerprinting technique. Previous studies conducted in this watershed showed that resuspension of fine sediment deposited on the stream bed is an important source of suspended sediment. To better understand the role of fine sediment deposited on the stream bed, fallout radionuclides,137Cs and 210Pbxs were used to determine relative contribution to suspended sediment from in-stream (stream bank and stream bed) and upland sediment sources. Suspended sediment samples were collected during the crop growing season. Potential sources of suspended sediment considered in this study included cropland, pasture and in-stream (stream bed and stream bank). Suspended sediment sources were determined at a subwatershed level. Results of this study showed that in-stream sediment sources are important sources of suspended sediment. Future research should be conducted to better understand the role of legacy sediment in watershed-level sediment transport processes.

Water soluble organic aerosols in the Colorado Rocky Mountains, USA: composition, sources and optical properties

PubMed Central

Xie, Mingjie; Mladenov, Natalie; Williams, Mark W.; Neff, Jason C.; Wasswa, Joseph; Hannigan, Michael P.

2016-01-01

Atmospheric aerosols have been shown to be an important input of organic carbon and nutrients to alpine watersheds and influence biogeochemical processes in these remote settings. For many remote, high elevation watersheds, direct evidence of the sources of water soluble organic aerosols and their chemical and optical characteristics is lacking. Here, we show that the concentration of water soluble organic carbon (WSOC) in the total suspended particulate (TSP) load at a high elevation site in the Colorado Rocky Mountains was strongly correlated with UV absorbance at 254 nm (Abs254, r = 0.88 p < 0.01) and organic carbon (OC, r = 0.95 p < 0.01), accounting for >90% of OC on average. According to source apportionment analysis, biomass burning had the highest contribution (50.3%) to average WSOC concentration; SOA formation and motor vehicle emissions dominated the contribution to WSOC in the summer. The source apportionment and backward trajectory analysis results supported the notion that both wildfire and Colorado Front Range pollution sources contribute to the summertime OC peaks observed in wet deposition at high elevation sites in the Colorado Rocky Mountains. These findings have important implications for water quality in remote, high-elevation, mountain catchments considered to be our pristine reference sites. PMID:27991554

Application of stochastic models in identification and apportionment of heavy metal pollution sources in the surface soils of a large-scale region.

PubMed

Hu, Yuanan; Cheng, Hefa

2013-04-16

As heavy metals occur naturally in soils at measurable concentrations and their natural background contents have significant spatial variations, identification and apportionment of heavy metal pollution sources across large-scale regions is a challenging task. Stochastic models, including the recently developed conditional inference tree (CIT) and the finite mixture distribution model (FMDM), were applied to identify the sources of heavy metals found in the surface soils of the Pearl River Delta, China, and to apportion the contributions from natural background and human activities. Regression trees were successfully developed for the concentrations of Cd, Cu, Zn, Pb, Cr, Ni, As, and Hg in 227 soil samples from a region of over 7.2 × 10(4) km(2) based on seven specific predictors relevant to the source and behavior of heavy metals: land use, soil type, soil organic carbon content, population density, gross domestic product per capita, and the lengths and classes of the roads surrounding the sampling sites. The CIT and FMDM results consistently indicate that Cd, Zn, Cu, Pb, and Cr in the surface soils of the PRD were contributed largely by anthropogenic sources, whereas As, Ni, and Hg in the surface soils mostly originated from the soil parent materials.

DUALITY IN MULTIVARIATE RECEPTOR MODEL. (R831078)

EPA Science Inventory

Multivariate receptor models are used for source apportionment of multiple observations of compositional data of air pollutants that obey mass conservation. Singular value decomposition of the data leads to two sets of eigenvectors. One set of eigenvectors spans a space in whi...

"OZONE SOURCE APPORTIONMENT IN CMAQ' | Science ...

EPA Pesticide Factsheets

Ozone source attribution has been used to support various policy purposes including interstate transport (Cross State Air Pollution Rule) by U.S. EPA and ozone nonattainment area designations by State agencies. Common scientific applications include tracking intercontinental transport of ozone and ozone precursors and delineating anthropogenic and non-anthropogenic contribution to ozone in North America. As in the public release due in September 2013, CMAQ’s Integrated Source Apportionment Method (ISAM) attributes PM EC/OC, sulfate, nitrate, ammonium, ozone and its precursors NOx and VOC, to sectors/regions of users’ interest. Although the peroxide-to-nitric acid productions ratio has been the most common indicator to distinguish NOx-limited ozone production from VOC-limited one, other indicators are implemented in addition to allowing for an ensemble decision based on a total of 9 available indicator ratios. Moreover, an alternative approach of ozone attribution based on the idea of chemical sensitivity in a linearized system that has formed the basis of chemical treatment in forward DDM/backward adjoint tools has been implemented in CMAQ. This method does not require categorization into either ozone regime. In this study, ISAM will simulate the 2010 North America ozone using all of the above gas-phase attribution methods. The results are to be compared with zero-out difference out of those sectors in the host model runs. In addition, ozone contribution wil

Characterization and source apportionment of particulate matter < or = 2.5 micrometer in Sumatra, Indonesia, during a recent peat fire episode.

PubMed

See, Siao Wei; Balasubramanian, Rajasekhar; Rianawati, Elisabeth; Karthikeyan, Sathrugnan; Streets, David G

2007-05-15

An intensive field study was conducted in Sumatra, Indonesia, during a peat fire episode to investigate the physical and chemical characteristics of particulate emissions in peat smoke and to provide necessary data for source-receptor analyses. Ambient air sampling was carried out at three different sites located at varying distances from the peatfires to determine changes in mass and number concentrations of PM2.5 and its chemical composition (carbonaceous and nitrogenous materials, polycyclic aromatic hydrocarbons, water-soluble inorganic and organic ions, and total and water-soluble metals). The three sites represent a rural site directly affected by the local peat combustion, a semirural site, and an urban site situated downwind of the peat fires. The mass concentration of PM2.5 and the number concentration of airborne particles were as high as 1600 microg/m3 and 1.7 x 10(5) cm(-3), respectively, in the vicinity of peat fires. The major components of PM2.5 in peat smoke haze were carbonaceous particles, particularly organic carbon, NO3-, and SO4(2-), while the less abundant constituents included ions such as NH4+, NO2-, Na+, K+, organic acids, and metals such as Al, Fe, and Ti. Source apportionment by chemical mass balance receptor modeling indicates that peat smoke can travel long distances and significantly affect the air quality at locations downwind.

[Transfer characteristic and source identification of soil heavy metals from water-level-fluctuating zone along Xiangxi River, three-Gorges Reservoir area].

PubMed

Xu, Tao; Wang, Fei; Guo, Qiang; Nie, Xiao-Qian; Huang, Ying-Ping; Chen, Jun

2014-04-01

Transfer characteristics of heavy metals and their evaluation of potential risk were studied based on determining concentration of heavy metal in soils from water-level-fluctuating zone (altitude:145-175 m) and bank (altitude: 175-185 m) along Xiangxi River, Three Gorges Reservoir area. Factor analysis-multiple linear regression (FA-MLR) was employed for heavy metal source identification and source apportionment. Results demonstrate that, during exposing season, the concentration of soil heavy metals in water-level-fluctuation zone and bank showed the variation, and the concentration of soil heavy metals reduced in shallow soil, but increased in deep soil at water-level-fluctuation zone. However, the concentration of soil heavy metals reduced in both shallow and deep soil at bank during the same period. According to the geoaccumulation index,the pollution extent of heavy metals followed the order: Cd > Pb > Cu > Cr, Cd is the primary pollutant. FA and FA-MLR reveal that in soils from water-level-fluctuation zone, 75.60% of Pb originates from traffic, 62.03% of Cd is from agriculture, 64.71% of Cu and 75.36% of Cr are from natural rock. In soils from bank, 82.26% of Pb originates from traffic, 68.63% of Cd is from agriculture, 65.72% of Cu and 69.33% of Cr are from natural rock. In conclusion, FA-MLR can successfully identify source of heavy metal and compute source apportionment of heavy metals, meanwhile the transfer characteristic is revealed. All these information can be a reference for heavy metal pollution control.

Source apportionment of volatile organic compounds measured near a cold heavy oil production area

NASA Astrophysics Data System (ADS)

Aklilu, Yayne-abeba; Cho, Sunny; Zhang, Qianyu; Taylor, Emily

2018-07-01

This study investigated sources of volatile organic compounds (VOCs) observed during periods of elevated hydrocarbon concentrations adjacent to a cold heavy oil extraction area in Alberta, Canada. Elevated total hydrocarbon (THC) concentrations were observed during the early morning hours and were associated with meteorological conditions indicative of gravitational drainage flows. THC concentrations were higher during the colder months, an occurrence likely promoted by a lower mixing height. On the other hand, other VOCs had higher concentrations in the summer; this is likely due to increased evaporation and atmospheric chemistry during the summer months. Of all investigated VOC compounds, alkanes contributed the greatest in all seasons. A source apportionment method, positive matrix factorization (PMF), was used to identify the potential contribution of various sources to the observed VOC concentrations. A total of five factors were apportioned including Benzene/Hexane, Oil Evaporative, Toluene/Xylene, Acetone and Assorted Local/Regional Air Masses. Three of the five factors (i.e., Benzene/Hexane, Oil Evaporative, and Toluene/Xylene), formed 27% of the reconstructed and unassigned concentration and are likely associated with emissions from heavy oil extraction. The three factors associated with emissions were comparable to the available emission inventory for the area. Potential sources include solution gas venting, combustion exhaust and fugitive emissions from extraction process additives. The remaining two factors (i.e., Acetone and Assorted Local/Regional Air Mass), comprised 49% of the reconstructed and unassigned concentration and contain key VOCs associated with atmospheric chemistry or the local/regional air mass such as acetone, carbonyl sulphide, Freon-11 and butane.

Characterizing and sourcing ambient PM2.5 over key emission regions in China III: Carbon isotope based source apportionment of black carbon

NASA Astrophysics Data System (ADS)

Yu, Kuangyou; Xing, Zhenyu; Huang, Xiaofeng; Deng, Junjun; Andersson, August; Fang, Wenzheng; Gustafsson, Örjan; Zhou, Jiabin; Du, Ke

2018-03-01

Regional haze over China has severe implications for air quality and regional climate. To effectively combat these effects the high uncertainties regarding the emissions from different sources needs to be reduced. In this paper, which is the third in a series on the sources of PM2.5 in pollution hotspot regions of China, we focus on the sources of black carbon aerosols (BC), using carbon isotope signatures. Four-season samples were collected at two key locations: Beijing-Tianjin-Hebei (BTH, part of Northern China plain), and the Pearl River Delta (PRD). We find that that fossil fuel combustion was the predominant source of BC in both BTH and PRD regions, accounting for 75 ± 5%. However, the contributions of what fossil fuel components were dominating differed significantly between BTH and PRD, and varied dramatically with seasons. Coal combustion is overall the all-important BC source in BTH, accounting for 46 ± 12% of the BC in BTH, with the maximum value (62%) found in winter. In contrast for the PRD region, liquid fossil fuel combustion (e.g., oil, diesel, and gasoline) is the dominant source of BC, with an annual mean value of 41 ± 15% and the maximum value of 55% found in winter. Region- and season-specific source apportionments are recommended to both accurately assess the climate impact of carbonaceous aerosol emissions and to effectively mitigate deteriorating air quality caused by carbonaceous aerosols.

PMF5.0 vs. CMB8.2: An inter-comparison study based on the new European SPECIEUROPE database

NASA Astrophysics Data System (ADS)

Bove, Maria Chiara; Massabò, Dario; Prati, Paolo

2018-03-01

Receptor Models are tools widely adopted in source apportionment studies. We describe here an experiment in which we integrated two different approaches, i.e. Positive Matrix Factorization (PMF) and Chemical Mass Balance (CMB) to apportion a set of PM10 (i.e. Particulate Matter with aerodynamic diameter lower than 10 μm) concentration values. The study was performed in the city of Genoa (Italy): a sampling campaign was carried out collecting daily PM10 samples for about two months in an urban background site. PM10 was collected on Quartz fiber filters by a low-volume sampler. A quite complete speciation of PM samples was obtained via Energy Dispersive-X Ray Fluorescence (ED-XRF, for elements), Ionic Chromatography (IC, for major ions and levoglucosan), thermo-optical Analysis (TOT, for organic and elemental carbon). The chemical analyses provided the input database for source apportionment by both PMF and CMB. Source profiles were directly calculated from the input data by PMF while in the CMB runs they were first calculated by averaging the profiles of similar sources collected in the European database SPECIEUROPE. Differences between the two receptor models emerged in particular with PM10 sources linked to very local processes. For this reason, PMF source profiles were adopted in refined CMB runs thus testing a new hybrid approach. Finally, PMF and the "tuned" CMB showed a better agreement even if some discrepancies could not completely been resolved. In this work, we compared the results coming from the last available PMF and CMB versions applied on a set of PM10 samples. Input profiles used in CMB analysis were obtained by averaging the profiles of the new European SPECIEUROPE database. The main differences between PMF and CMB results were linked to very local processes: we obtained the best solution by integrating the two different approaches with the implementation of some output PMF profiles to CMB runs.

Fine particle receptor modeling in the atmosphere of Mexico City.

PubMed

Vega, Elizabeth; Lowenthal, Douglas; Ruiz, Hugo; Reyes, Elizabeth; Watson, John G; Chow, Judith C; Viana, Mar; Querol, Xavier; Alastuey, Andrés

2009-12-01

Source apportionment analyses were carried out by means of receptor modeling techniques to determine the contribution of major fine particulate matter (PM2.5) sources found at six sites in Mexico City. Thirty-six source profiles were determined within Mexico City to establish the fingerprints of particulate matter sources. Additionally, the profiles under the same source category were averaged using cluster analysis and the fingerprints of 10 sources were included. Before application of the chemical mass balance (CMB), several tests were carried out to determine the best combination of source profiles and species used for the fitting. CMB results showed significant spatial variations in source contributions among the six sites that are influenced by local soil types and land use. On average, 24-hr PM2.5 concentrations were dominated by mobile source emissions (45%), followed by secondary inorganic aerosols (16%) and geological material (17%). Industrial emissions representing oil combustion and incineration contributed less than 5%, and their contribution was higher at the industrial areas of Tlalnepantla (11%) and Xalostoc (8%). Other sources such as cooking, biomass burning, and oil fuel combustion were identified at lower levels. A second receptor model (principal component analysis, [PCA]) was subsequently applied to three of the monitoring sites for comparison purposes. Although differences were obtained between source contributions, results evidence the advantages of the combined use of different receptor modeling techniques for source apportionment, given the complementary nature of their results. Further research is needed in this direction to reach a better agreement between the estimated source contributions to the particulate matter mass.

Direct atmospheric deposition of 210Pb to rivers determined through 210Pb (210Po) disequilibrium and implications to sediment source apportionment

NASA Astrophysics Data System (ADS)

Blumentritt, D. J.; Shottler, S.; Engstrom, D. R.

2011-12-01

Atmospheric radioisotopes such as 210Pb can be an effective tool for determining sediment source types in rivers and streams. Pb-210 is ubiquitous in deposition from atmospheric washout and is highly particle reactive, so sediments derived from a surface with prolonged exposure to rainfall, such as farm fields, are enriched in atmospheric 210Pb. Conversely, sediment sources that are not readily exposed to rainfall (i.e. streambanks) are absent of any appreciable 210Pb. Many sediment source apportionment studies have used 210Pb to quantify the proportion of sediment loads from the two source types, field and non-field. These studies, however, primarily take place in smaller watersheds where 210Pb that falls directly onto the surface of the water is assumed negligible. Lake Pepin is a riverine lake located in southeastern Minnesota with a 122,000 km2 watershed composed of three major rivers, the Minnesota, headwaters Mississippi, and St. Croix. The sediment load in Lake Pepin has increased by an order of magnitude since Euro-American settlement in the region. Most of the sediment (>80%) is transported to Lake Pepin from the highly agricultural Minnesota River basin. Extensive sediment fingerprinting work has been done on Lake Pepin sediments, but a source of significant uncertainty still exists: How much of the 210Pb measured in Lake Pepin is directly deposited to the surface of the contributing water bodies and did not enter on eroded particles? To answer this important question, we have developed a method to quantify the amount of directly deposited 210Pb. Alpha spectrometry is used to measure 210Po, a daughter product of 210Pb decay. Because 210Po has a short half-life (138 days), it takes approximately one year to reach equilibrium with 210Pb on sediment particles. If deposition of 210Pb directly from the atmosphere to the water surface is significant, there will be disequilibrium between the two radioisotopes and the activity of 210Po will increase as an inverse exponential function, with respect to time, following sample collection. The magnitude of this increase is the amount of directly deposited 210Pb. Samples were collected at four locations, corresponding to gauging stations, on the Minnesota/Mississippi River system above Lake Pepin. Three measurements were made on each sample over the course of a year after collection. Based on those three measurements, the activity of 210Po was modeled for time zero and for the equilibrium concentration, revealing the amount of 210Pb from direct atmospheric deposition. These estimates were flow-weighted over the course of the year, providing a critical correction to the source apportionment model.

Source apportionment modeling of volatile organic compounds in streams

USGS Publications Warehouse

Pankow, J.F.; Asher, W.E.; Zogorski, J.S.

2006-01-01

It often is of interest to understand the relative importance of the different sources contributing to the concentration cw of a contaminant in a stream; the portions related to sources 1, 2, 3, etc. are denoted cw,1, cw,2, cw,3, etc. Like c w, 'he fractions ??1, = cw,1/c w, ??2 = cw,2/cw, ??3 = cw,3/cw, etc. depend on location and time. Volatile organic compounds (VOCs) can undergo absorption from the atmosphere into stream water or loss from stream water to the atmosphere, causing complexities affecting the source apportionment (SA) of VOCs in streams. Two SA rules are elaborated. Rule 1: VOC entering a stream across the air/water interface exclusively is assigned to the atmospheric portion of cw. Rule 2: VOC loss by volatilization, flow loss to groundwater, in-stream degradation, etc. is distributed over cw,1 cw,2, c w,3, etc. in proportion to their corresponding ?? values. How the two SA rules are applied, as well as the nature of the SA output for a given case, will depend on whether transport across the air/water interface is handled using the net flux F convention or using the individual fluxes J convention. Four hypothetical stream cases involving acetone, methyl-tert-butyl ether (MTBE), benzene, chloroform, and perchloroethylene (PCE) are considered. Acetone and MTBE are sufficiently water soluble from air for a domestic atmospheric source to be capable of yielding cw values approaching the common water quality guideline range of 1 to 10 ??g/L. For most other VOCs, such levels cause net outgassing (F > 0). When F > 0 in a given section of stream, in the net flux convention, all of the ??j, for the compound remain unchanged over that section while cw decreases. A characteristic time ??d can be calculated to predict when there will be differences between SA results obtained by the net flux convention versus the individual fluxes convention. Source apportionment modeling provides the framework necessary for comparing different strategies for mitigating contamination at points of interest along a stream. ?? 2006 SETAC.

Spatial Gradients and Source Apportionment of Volatile Organic Compounds Near Roadways

EPA Science Inventory

Concentrations of 55 volatile organic compounds (VOCs) are reported near a highway in Raleigh, NC (traffic volume of approximately 125,000 vehicles/day). Levels of VOCs generally decreased exponentially with perpendicular distance from the roadway 10-100m). The EPA Chemical Mass ...

Quantification of source impact to PM using three-dimensional weighted factor model analysis on multi-site data

NASA Astrophysics Data System (ADS)

Shi, Guoliang; Peng, Xing; Huangfu, Yanqi; Wang, Wei; Xu, Jiao; Tian, Yingze; Feng, Yinchang; Ivey, Cesunica E.; Russell, Armistead G.

2017-07-01

Source apportionment technologies are used to understand the impacts of important sources of particulate matter (PM) air quality, and are widely used for both scientific studies and air quality management. Generally, receptor models apportion speciated PM data from a single sampling site. With the development of large scale monitoring networks, PM speciation are observed at multiple sites in an urban area. For these situations, the models should account for three factors, or dimensions, of the PM, including the chemical species concentrations, sampling periods and sampling site information, suggesting the potential power of a three-dimensional source apportionment approach. However, the principle of three-dimensional Parallel Factor Analysis (Ordinary PARAFAC) model does not always work well in real environmental situations for multi-site receptor datasets. In this work, a new three-way receptor model, called "multi-site three way factor analysis" model is proposed to deal with the multi-site receptor datasets. Synthetic datasets were developed and introduced into the new model to test its performance. Average absolute error (AAE, between estimated and true contributions) for extracted sources were all less than 50%. Additionally, three-dimensional ambient datasets from a Chinese mega-city, Chengdu, were analyzed using this new model to assess the application. Four factors are extracted by the multi-site WFA3 model: secondary source have the highest contributions (64.73 and 56.24 μg/m3), followed by vehicular exhaust (30.13 and 33.60 μg/m3), crustal dust (26.12 and 29.99 μg/m3) and coal combustion (10.73 and 14.83 μg/m3). The model was also compared to PMF, with general agreement, though PMF suggested a lower crustal contribution.

Ambient PM2.5-bound polycyclic aromatic hydrocarbons (PAHs) in Changhua County, central Taiwan: Seasonal variation, source apportionment and cancer risk assessment.

PubMed

Chen, Yu-Cheng; Chiang, Hung-Che; Hsu, Chin-Yu; Yang, Tzu-Ting; Lin, Tzu-Yu; Chen, Mu-Jean; Chen, Nai-Tzu; Wu, Yuh-Shen

2016-11-01

This study investigates PM 2.5 -bound PAHs for rural sites (Dacheng and Fangyuan) positioned close to heavy air-polluting industries in Changhua County, central Taiwan. A total of 113 PM 2.5 samples with 22 PAHs collected from 2014 to 2015 were analyzed, and Positive Matrix Factorization (PMF) and diagnostic ratios of PAHs were applied to quantify potential PAH sources. The influences of local and regional sources were also explored using the conditional probability function (CPF) and potential source contribution function (PSCF) with PMF-modeled results, respectively. Annual mean concentrations of total PAHs were 2.91 ± 1.34 and 3.04 ± 1.40 ng/m 3 for Dacheng and Fangyuan, respectively, and their corresponding BaP eq were measured at 0.534 ± 0.255 and 0.563 ± 0.273 ng/m 3 in concentration. Seasonal variations with higher PAHs found for the winter than for the spring and summer were observed for both sites. The lifetime excess cancer risk (ECR) from inhalation exposure to PAHs was recorded as 4.7 × 10 -5 overall. Potential sources of PM 2.5 -bound PAHs include unburned petroleum and traffic emissions (42%), steel industry and coal combustion (31%), and petroleum and oil burning (27%), and unburned petroleum and traffic emission could contribute the highest ECR (2.4 × 10 -5 ). The CPF results show that directional apportionment patterns were consistent with the actual locations of local PAH sources. The PSCF results indicate that mainly northeastern regions of China have contributed elevated PM 2.5 -bound PAHs from long-range transports. Copyright © 2016 Elsevier Ltd. All rights reserved.

Application of hierarchical Bayesian unmixing models in river sediment source apportionment

NASA Astrophysics Data System (ADS)

Blake, Will; Smith, Hugh; Navas, Ana; Bodé, Samuel; Goddard, Rupert; Zou Kuzyk, Zou; Lennard, Amy; Lobb, David; Owens, Phil; Palazon, Leticia; Petticrew, Ellen; Gaspar, Leticia; Stock, Brian; Boeckx, Pacsal; Semmens, Brice

2016-04-01

Fingerprinting and unmixing concepts are used widely across environmental disciplines for forensic evaluation of pollutant sources. In aquatic and marine systems, this includes tracking the source of organic and inorganic pollutants in water and linking problem sediment to soil erosion and land use sources. It is, however, the particular complexity of ecological systems that has driven creation of the most sophisticated mixing models, primarily to (i) evaluate diet composition in complex ecological food webs, (ii) inform population structure and (iii) explore animal movement. In the context of the new hierarchical Bayesian unmixing model, MIXSIAR, developed to characterise intra-population niche variation in ecological systems, we evaluate the linkage between ecological 'prey' and 'consumer' concepts and river basin sediment 'source' and sediment 'mixtures' to exemplify the value of ecological modelling tools to river basin science. Recent studies have outlined advantages presented by Bayesian unmixing approaches in handling complex source and mixture datasets while dealing appropriately with uncertainty in parameter probability distributions. MixSIAR is unique in that it allows individual fixed and random effects associated with mixture hierarchy, i.e. factors that might exert an influence on model outcome for mixture groups, to be explored within the source-receptor framework. This offers new and powerful ways of interpreting river basin apportionment data. In this contribution, key components of the model are evaluated in the context of common experimental designs for sediment fingerprinting studies namely simple, nested and distributed catchment sampling programmes. Illustrative examples using geochemical and compound specific stable isotope datasets are presented and used to discuss best practice with specific attention to (1) the tracer selection process, (2) incorporation of fixed effects relating to sample timeframe and sediment type in the modelling process, (3) deriving and using informative priors in sediment fingerprinting context and (4) transparency of the process and replication of model results by other users.

Navy Littoral Combat Ship (LCS) Program: Background, Issues, and Options for Congress

DTIC Science & Technology

2011-01-11

response, including the time for reviewing instructions, searching existing data sources , gathering and maintaining the data needed, and completing and... Source : Source : U.S. Navy file photo accessed by CRS at http://www.navy.mil/list_all.asp?id=57917 on January 6, 2010. Navy Littoral Combat Ship...above the target cost and up to the ceiling cost would be shared between the contractor and the Navy according to an agreed apportionment (i.e., a

Atmospheric deposition of polycyclic aromatic hydrocarbons near New England coastal waters

NASA Astrophysics Data System (ADS)

Golomb, D.; Barry, E.; Fisher, G.; Varanusupakul, P.; Koleda, M.; Rooney, T.

Wet and dry deposition of polycyclic aromatic hydrocarbons (PAHs) was measured at Nahant, Massachusetts, a peninsula jutting into Massachusetts Bay and Wolf Neck, a peninsula jutting into Casco Bay, Maine. Wet deposition (rain and snow) was collected in a funnel which drains into a shielded, temperature controlled receiving bottle. Dry deposition of gaseous and particulate PAHs was collected onto an exposed water surface. PAHs were analyzed by solid phase extraction and gas chromatography-mass spectrometry. Sixteen PAH species were analyzed, ranging from acenaphthylene to coronene. The mean wet deposition rate of the sum of the 16 species is 720 ng m -2 cm -1 precipitation at Nahant, and 831 ng m -2 cm -1 precipitation at Wolf Neck. Wet deposition is attributed to regional PAH emitting sources. Storm patterns appear to bring somewhat higher wet deposition of PAHs to Wolf Neck than to Nahant. The mean dry deposition rate is 95 ng m -2 h -1 at Nahant and 9.3 ng m -2 h -1 at Wolf Neck. The large difference is attributed to the fact that Nahant is close to the urban-industrial metropolitan Boston area and Logan International Airport, whereas Wolf Neck has no major PAH-emitting sources nearby. Individual measurements have an error bracket of ±30%. The Chemical Mass Balance model was used to apportion the dry deposition to source categories. At Nahant, nine samples gave valid statistical attributes with a mean apportionment: jet exhaust 35%, gasoline fueled vehicles 32%, diesel fueled vehicles 17%, wood combustion 13%, others 3%. At Wolf Neck, six samples yielded a mean apportionment: jet exhaust 30%, gasoline vehicles 28%, diesel vehicles 18%, wood combustion 16%, others 8%. There is a considerable variation between the samples. The apportionment is greatly dependent on the quality and selection of the model inputs, i.e. source signatures, which for PAHs are questionable.

Source apportionment of aerosol particles at a European air pollution hot spot using particle number size distributions and chemical composition.

PubMed

Leoni, Cecilia; Pokorná, Petra; Hovorka, Jan; Masiol, Mauro; Topinka, Jan; Zhao, Yongjing; Křůmal, Kamil; Cliff, Steven; Mikuška, Pavel; Hopke, Philip K

2018-03-01

Ostrava in the Moravian-Silesian region (Czech Republic) is a European air pollution hot spot for airborne particulate matter (PM), polycyclic aromatic hydrocarbons (PAHs), and ultrafine particles (UFPs). Air pollution source apportionment is essential for implementation of successful abatement strategies. UFPs or nanoparticles of diameter <100 nm exhibit the highest deposition efficiency in human lungs. To permit apportionment of PM sources at the hot-spot including nanoparticles, Positive Matrix Factorization (PMF) was applied to highly time resolved particle number size distributions (NSD, 14 nm-10 μm) and PM 0.09-1.15 chemical composition. Diurnal patterns, meteorological variables, gaseous pollutants, organic markers, and associations between the NSD factors and chemical composition factors were used to identify the pollution sources. The PMF on the NSD reveals two factors in the ultrafine size range: industrial UFPs (28%, number mode diameter - NMD 45 nm), industrial/fresh road traffic nanoparticles (26%, NMD 26 nm); three factors in the accumulation size range: urban background (24%, NMD 93 nm), coal burning (14%, volume mode diameter - VMD 0.5 μm), regional pollution (3%, VMD 0.8 μm) and one factor in the coarse size range: industrial coarse particles/road dust (2%, VMD 5 μm). The PMF analysis of PM 0.09-1.15 revealed four factors: SIA/CC/BB (52%), road dust (18%), sinter/steel (16%), iron production (16%). The factors in the ultrafine size range resolved with NSD have a positive correlation with sinter/steel production and iron production factors resolved with chemical composition. Coal combustion factor resolved with NSD has moderate correlation with SIA/CC/BB factor. The organic markers homohopanes correlate with coal combustion and the levoglucosan correlates with urban background. The PMF applications to NSD and chemical composition datasets are complementary. PAHs in PM 1 were found to be associated with coal combustion factor. Copyright © 2017 Elsevier Ltd. All rights reserved.

BTEX exposures in an area impacted by industrial and mobile sources: Source attribution and impact of averaging time.

PubMed

Presto, Albert A; Dallmann, Timothy R; Gu, Peishi; Rao, Unnati

2016-04-01

The impacts of emissions plumes from major industrial sources on black carbon (BC) and BTEX (benzene, toluene, ethyl benzene, xylene isomers) exposures in communities located >10 km from the industrial source areas were identified with a combination of stationary measurements, source identification using positive matrix factorization (PMF), and dispersion modeling. The industrial emissions create multihour plume events of BC and BTEX at the measurement sites. PMF source apportionment, along with wind patterns, indicates that the observed pollutant plumes are the result of transport of industrial emissions under conditions of low boundary layer height. PMF indicates that industrial emissions contribute >50% of outdoor exposures of BC and BTEX species at the receptor sites. Dispersion modeling of BTEX emissions from known industrial sources predicts numerous overnight plumes and overall qualitative agreement with PMF analysis, but predicts industrial impacts at the measurement sites a factor of 10 lower than PMF. Nonetheless, exposures associated with pollutant plumes occur mostly at night, when residents are expected to be home but are perhaps unaware of the elevated exposure. Averaging data samples over long times typical of public health interventions (e.g., weekly or biweekly passive sampling) misapportions the exposure, reducing the impact of industrial plumes at the expense of traffic emissions, because the longer samples cannot resolve subdaily plumes. Suggestions are made for ways for future distributed pollutant mapping or intervention studies to incorporate high time resolution tools to better understand the potential impacts of industrial plumes. Emissions from industrial or other stationary sources can dominate air toxics exposures in communities both near the source and in downwind areas in the form of multihour plume events. Common measurement strategies that use highly aggregated samples, such as weekly or biweekly averages, are insensitive to such plume events and can lead to significant under apportionment of exposures from these sources.

Chemical composition and source apportionment of size fractionated particulate matter in Cleveland, Ohio, USA.

PubMed

Kim, Yong Ho; Krantz, Q Todd; McGee, John; Kovalcik, Kasey D; Duvall, Rachelle M; Willis, Robert D; Kamal, Ali S; Landis, Matthew S; Norris, Gary A; Gilmour, M Ian

2016-11-01

The Cleveland airshed comprises a complex mixture of industrial source emissions that contribute to periods of non-attainment for fine particulate matter (PM 2.5 ) and are associated with increased adverse health outcomes in the exposed population. Specific PM sources responsible for health effects however are not fully understood. Size-fractionated PM (coarse, fine, and ultrafine) samples were collected using a ChemVol sampler at an urban site (G.T. Craig (GTC)) and rural site (Chippewa Lake (CLM)) from July 2009 to June 2010, and then chemically analyzed. The resulting speciated PM data were apportioned by EPA positive matrix factorization to identify emission sources for each size fraction and location. For comparisons with the ChemVol results, PM samples were also collected with sequential dichotomous and passive samplers, and evaluated for source contributions to each sampling site. The ChemVol results showed that annual average concentrations of PM, elemental carbon, and inorganic elements in the coarse fraction at GTC were ∼2, ∼7, and ∼3 times higher than those at CLM, respectively, while the smaller size fractions at both sites showed similar annual average concentrations. Seasonal variations of secondary aerosols (e.g., high NO 3 - level in winter and high SO 4 2- level in summer) were observed at both sites. Source apportionment results demonstrated that the PM samples at GTC and CLM were enriched with local industrial sources (e.g., steel plant and coal-fired power plant) but their contributions were influenced by meteorological conditions and the emission source's operation conditions. Taken together the year-long PM collection and data analysis provides valuable insights into the characteristics and sources of PM impacting the Cleveland airshed in both the urban center and the rural upwind background locations. These data will be used to classify the PM samples for toxicology studies to determine which PM sources, species, and size fractions are of greatest health concern. Copyright © 2016 Elsevier Ltd. All rights reserved.

Atmospheric Aerosol Source-Receptor Relationships: The Role of Coal-Fired Power Plants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Allen L. Robinson; Spyros N. Pandis; Cliff I. Davidson

2005-12-01

This report describes the technical progress made on the Pittsburgh Air Quality Study (PAQS) during the period of March 2005 through August 2005. Significant progress was made this project period on the source characterization, source apportionment, and deterministic modeling activities. This report highlights new data on road dust, vegetative detritus and motor vehicle emissions. For example, the results show significant differences in the composition in urban and rural road dust. A comparison of the organic of the fine particulate matter in the tunnel with the ambient provides clear evidence of the significant contribution of vehicle emissions to ambient PM. Themore » source profiles developed from this work are being used by the source-receptor modeling activities. The report presents results on the spatial distribution of PMF-factors. The results can be grouped into three different categories: regional sources, local sources, or potentially both regional and local sources. Examples of the regional sources are the sulfate and selenium PMF-factors which most likely-represent coal fired power plants. Examples of local sources are the specialty steel and lead factors. There is reasonable correspondence between these apportionments and data from the EPA TRI and AIRS emission inventories. Detailed comparisons between PMCAMx predictions and measurements by the STN and IMPROVE measurements in the Eastern US are presented. Comparisons were made for the major aerosol components and PM{sub 2.5} mass in July 2001, October 2001, January 2002, and April 2002. The results are encouraging with average fraction biases for most species less than 0.25. The improvement of the model performance during the last two years was mainly due to the comparison of the model predictions with the continuous measurements in the Pittsburgh Supersite. Major improvements have included the descriptions: of ammonia emissions (CMU inventory), night time nitrate chemistry, EC emissions and their diurnal variation, and nitric acid dry removal.« less

A framework for emissions source apportionment in industrial areas: MM5/CALPUFF in a near-field application.

PubMed

Ghannam, K; El-Fadel, M

2013-02-01

This paper examines the relative source contribution to ground-level concentrations of carbon monoxide (CO), nitrogen dioxide (NO2), and PM10 (particulate matter with an aerodynamic diameter < 10 microm) in a coastal urban area due to emissions from an industrial complex with multiple stacks, quarrying activities, and a nearby highway. For this purpose, an inventory of CO, oxide of nitrogen (NO(x)), and PM10 emissions was coupled with the non-steady-state Mesoscale Model 5/California Puff Dispersion Modeling system to simulate individual source contributions under several spatial and temporal scales. As the contribution of a particular source to ground-level concentrations can be evaluated by simulating this single-source emissions or otherwise total emissions except that source, a set of emission sensitivity simulations was designed to examine if CALPUFF maintains a linear relationship between emission rates and predicted concentrations in cases where emitted plumes overlap and chemical transformations are simulated. Source apportionment revealed that ground-level releases (i.e., highway and quarries) extended over large areas dominated the contribution to exposure levels over elevated point sources, despite the fact that cumulative emissions from point sources are higher. Sensitivity analysis indicated that chemical transformations of NO(x) are insignificant, possibly due to short-range plume transport, with CALPUFF exhibiting a linear response to changes in emission rate. The current paper points to the significance of ground-level emissions in contributing to urban air pollution exposure and questions the viability of the prevailing paradigm of point-source emission reduction, especially that the incremental improvement in air quality associated with this common abatement strategy may not accomplish the desirable benefit in terms of lower exposure with costly emissions capping. The application of atmospheric dispersion models for source apportionment helps in identifying major contributors to regional air pollution. In industrial urban areas where multiple sources with different geometry contribute to emissions, ground-level releases extended over large areas such as roads and quarries often dominate the contribution to ground-level air pollution. Industrial emissions released at elevated stack heights may experience significant dilution, resulting in minor contribution to exposure at ground level. In such contexts, emission reduction, which is invariably the abatement strategy targeting industries at a significant investment in control equipment or process change, may result in minimal return on investment in terms of improvement in air quality at sensitive receptors.

REVIEW OF VOLATILE ORGANIC COMPOUND SOURCE APPORTIONMENT BY CHEMICAL MASS BALANCE. (R826237)

EPA Science Inventory

The chemical mass balance (CMB) receptor model has apportioned volatile organic compounds (VOCs) in more than 20 urban areas, mostly in the United States. These applications differ in terms of the total fraction apportioned, the calculation method, the chemical compounds used ...

GUIDELINES FOR THE APPLICATION OF SEM/EDX ANALYTICAL TECHNIQUES FOR FINE AND COARSE PM SAMPLES

EPA Science Inventory

Scanning Electron Microscopy (SEM) coupled with Energy-Dispersive X-ray analysis (EDX) is a powerful tool in the characterization and source apportionment of environmental particulate matter (PM), providing size, chemistry, and morphology of particles as small as a few tenths ...

Personal exposure to particulate PAHs and anthraquinone and oxidative DNA damages in humans.

PubMed

Wei, Yongjie; Han, In-Kyu; Hu, Min; Shao, Min; Zhang, Junfeng Jim; Tang, Xiaoyan

2010-11-01

Recent studies suggest that DNA oxidative damage be related to the chemical constituents of ambient particles. The purpose of this study was to examine whether particulate polycyclic aromatic hydrocarbons (PAHs) and quinone-structure chemicals increase body burden of oxidative stress in human exposed to heavy traffic volume. We recruited two nonsmoking security guards who worked at a university campus gate near a heavily trafficked road. Each subject wore a personal air sampler for 24h per day to estimate exposures to 24 PAHs and anthraquinone (AnQ) in PM(2.5). Daily pre- and post-work shift spot urines were collected for 29d from each subject. Urine samples were analyzed for 8-hydroxy-2'-deoxyguanosine (8-OHdG). Additionally, using 19 organic tracers other than 24 PAHs and AnQ, a receptor source apportionment model of chemical mass balance was applied to determine the contributions of sources on the PM: gasoline vehicle, diesel vehicle, coal burning, vegetable debris, cooking, natural gas and biomass burning. The relationship among urinary 8-OHdG, individual PAH, and AnQ was demonstrated as follows: the average urinary concentration of 8-OHdG was increased more than three times after 8-h work-shift than those before the work shift. All the 24 PAH and AnQ levels were positively and significantly associated with the post-work urinary 8-OHdG. The results from source apportionment suggest vehicular emission to be the dominant source of personal exposure to PM(2.5). Our finding indicates that personal air exposures to 24 individual PAHs and AnQ originating from traffic emissions are important in increasing oxidative burdens in human body. Copyright © 2010 Elsevier Ltd. All rights reserved.

Pharmaceuticals and personal care products (PPCPs) in urban and suburban rivers of Beijing, China: occurrence, source apportionment and potential ecological risk.

PubMed

Dai, Guohua; Wang, Bin; Fu, Chaochen; Dong, Rui; Huang, Jun; Deng, Shubo; Wang, Yujue; Yu, Gang

2016-04-01

This study analyzed 15 pharmaceuticals and personal care products (PPCPs) in two rivers with different urbanization levels in the surrounding watershed (urban and suburb) in Beijing, China. Along the rivers, effluent samples from wastewater treatment plants (WWTPs) and wastewater samples from direct discharge outlets were also collected to reveal their possible contribution to the occurrence of PPCPs in these two rivers. Among the 15 PPCPs, 14 compounds were detected with caffeine (maximum 11,900 ng L(-1)) being the dominant compound. The total concentration of the detected PPCPs in direct discharge outlets (median 4706 ng L(-1)) was much higher than that in river waters (2780 ng L(-1)) and WWTP effluents (1971 ng L(-1)). The suburban-influenced Liangshui River had significantly higher PPCP concentrations compared to the urban-influenced Qing River due to more input of untreated wastewater from direct discharge outlets. Source apportionment showed that approximately 55% of the total PPCPs were contributed by untreated wastewater in the suburban-influenced river. Finally, ecological risk assessment has been regarded as a necessary part of general research. According to the environmental risk assessment results, caffeine, trimethoprim and metoprolol were found to be the most critical compounds, due to their high risk quotient values. The results of the present study can provide useful information for future PPCP pollution control and sustainable water management in Beijing, China.

Pollution data analysis and characteristics of volatile organic compounds in the environment

NASA Astrophysics Data System (ADS)

Wang, Qi; Wang, Chěn; Hou, Lujian; Lv, Bo; WANG, Chén

2018-06-01

Volatile organic compounds (VOCs) have a wide range of sources and have a significant impact on the ecological environment and human health, which have attracted wide attention of many researchers. In this paper, the pollution characteristics of VOCs, the role of VOCs in atmospheric chemistry including OH reaction reactivity (LOH), Ozone Formation Potential (OFP) and SOA generation potential (SOAP), VOCs source apportionment were discussed and reviewed.

Source apportionment of methane and nitrous oxide in California's San Joaquin Valley at CalNex 2010 via positive matrix factorization

NASA Astrophysics Data System (ADS)

Guha, A.; Gentner, D. R.; Weber, R. J.; Provencal, R.; Goldstein, A. H.

2015-03-01

Sources of methane (CH4) and nitrous oxide (N2O) were investigated using measurements from a site in southeast Bakersfield as part of the CalNex (California at the Nexus of Air Quality and Climate Change) experiment from 15 May to 30 June 2010. Typical daily minimum mixing ratios of CH4 and N2O were higher than daily averages that were simultaneously observed at a similar latitude background station (NOAA, Mauna Loa) by approximately 70 and 0.5 ppb, respectively. Substantial enhancements of CH4 and N2O (hourly averages > 500 ppb and > 7 ppb, respectively) were routinely observed suggesting the presence of large regional sources. Collocated measurements of carbon monoxide (CO) and a range of volatile organic compounds (VOCs) (e.g. straight-chain and branched alkanes, cycloalkanes, chlorinated alkanes, aromatics, alcohols, isoprene, terpenes and ketones) were used with a Positive Matrix Factorization (PMF) source apportionment method to estimate the contribution of regional sources to observed enhancements of CH4 and N2O. The PMF technique provided a "top-down" deconstruction of ambient gas-phase observations into broad source categories, yielding a 7-factor solution. We identified these source factors as emissions from evaporative and fugitive; motor vehicles; livestock and dairy; agricultural and soil management; daytime light and temperature driven; non-vehicular urban; and nighttime terpene biogenics and anthropogenics. The dairy and livestock factor accounted for a majority of the CH4 (70-90%) enhancements during the duration of the experiments. Propagation of uncertainties in the PMF-derived factor profiles and time series from bootstrapping analysis resulted in a 29% uncertainty in the CH4 apportionment to this factor. The dairy and livestock factor was also a principal contributor to the daily enhancements of N2O (60-70%) with an uncertainty of 33%. Agriculture and soil management accounted for ~20-25% of N2O enhancements over the course of a day, not surprisingly given that organic and synthetic fertilizers are known to be a major source of N2O. The evaporative/fugitive source profile resembles a mix of petroleum operation and non-tailpipe evaporative gasoline sources, but was not responsible for any observed PMF resolved-CH4 enhancements. The vehicle emission source factor broadly matches VOC profiles of on-road exhaust sources and had no detected contribution to the N2O signals and negligible CH4 in the presence of a dominant dairy and livestock factor. The CalNex PMF study provides a measurement-based assessment of the state CH4 and N2O inventories for the southern San Joaquin valley. The state inventory attributes ~18% of the total N2O emissions to the transportation sector. Our PMF analysis directly contradicts the state inventory and demonstrates there were no discernible N2O emissions from the transportation sector.

Chemical Characterization and Source Apportionment of Indoor and Outdoor Fine Particulate Matter (PM2.5) in Retirement Communities of the Los Angeles Basin

PubMed Central

Hasheminassab, Sina; Daher, Nancy; Shafer, Martin M.; Schauer, James J.; Delfino, Ralph J.; Sioutas, Constantinos

2014-01-01

Concurrent indoor and outdoor measurements of fine particulate matter (PM2.5) were conducted at three retirement homes in the Los Angeles Basin during two separate phases (cold and warm) between 2005 and 2006. Indoor-to-outdoor relationships of PM2.5 chemical constituents were determined and sources of indoor and outdoor PM2.5 were evaluated using a molecular marker-based chemical mass balance (MM-CMB) model. Indoor levels of elemental carbon (EC) along with metals and trace elements were found to be significantly affected by outdoor sources. EC, in particular, displayed very high indoor-to-outdoor (I/O) mass ratios accompanied by strong I/O correlations, illustrating the significant impact of outdoor sources on indoor levels of EC. Similarly, indoor levels of polycyclic aromatic hydrocarbons (PAHs), hopanes, and steranes were strongly correlated with their outdoor components and displayed I/O ratios close to unity. On the other hand, concentrations of n-alkanes and organic acids inside the retirement communities were dominated by indoor sources (e.g. food cooking and consumer products), as indicated by their I/O ratios, which exceeded unity. Source apportionment results revealed that vehicular emissions were the major contributor to both indoor and outdoor PM2.5, accounting for 39 and 46% of total mass, respectively. Moreover, the contribution of vehicular sources to indoor levels was generally comparable to its corresponding outdoor estimate. Other water-insoluble organic matter (other WIOM), which accounts for emissions from uncharacterized primary biogenic sources, displayed a wider range of contributions, varying from 2 to 73% of PM2.5, across all sites and phases of the study. Lastly, higher indoor than outdoor contribution of other water-soluble organic matter (other WSOM) was evident at some of the sites, suggesting the production of secondary aerosols as well as direct emissions from primary sources (including cleaning or other consumer products) at the indoor environments. PMID:24880542

Characterizing and sourcing ambient PM2.5 over key emission regions in China II: Organic molecular markers and CMB modeling

NASA Astrophysics Data System (ADS)

Zhou, Jiabin; Xiong, Ying; Xing, Zhenyu; Deng, Junjun; Du, Ke

2017-08-01

From November 2012 to July 2013, a sampling campaign was completed for comprehensive characterization of PM2.5 over four key emission regions in China: Beijing-Tianjin-Hebei (BTH), Yangzi River Delta (YRD), Pearl River Delta (PRD), and Sichuan Basin (SB). A multi-method approach, adopting different analytical and receptor modeling methods, was employed to determine the relative abundances of region-specific air pollution constituents and contributions of emission sources. This paper is focused on organic molecular marker based source apportionment using chemical mass balance (CMB) receptor modeling. Analyses of the organic molecular markers revealed that vehicle emission, coal combustion, biomass burning, meat cooking and natural gas combustion were the major contributors to organic carbon (OC) in PM2.5. The vehicle emission dominated the sources contributing to OC in spring at four sampling sites. During wintertime, the coal combustion had highest contribution to OC at BTH site, while the major source contributing to OC at YRD and PRD sites was vehicle emission. In addition, the relative contributions of different emission sources to PM2.5 mass at a specific location site and in a specific season revealed seasonal and spatial variations across all four sampling locations. The largest contributor to PM2.5 mass was secondary sulfate (14-17%) in winter at the four sites. The vehicle emission was found to be the major source (14-21%) for PM2.5 mass at PRD site. The secondary ammonium has minor variation (4-5%) across the sites, confirming the influences of regional emission sources on these sites. The distinct patterns of seasonal and spatial variations of source apportionment observed in this study were consistent with the findings in our previous paper based upon water-soluble ions and carbonaceous fractions. This makes it essential for the local government to make season- and region-specific mitigation strategies for abating PM2.5 pollution in China.

Source apportionment of indoor, outdoor and personal PM2.5 exposure of pregnant women in Barcelona, Spain

NASA Astrophysics Data System (ADS)

Minguillón, M. C.; Schembari, A.; Triguero-Mas, M.; de Nazelle, A.; Dadvand, P.; Figueras, F.; Salvado, J. A.; Grimalt, J. O.; Nieuwenhuijsen, M.; Querol, X.

2012-11-01

Exposure to air pollution has been shown to adversely affect foetal development in the case of pregnant women. The present study aims to investigate the PM composition and sources influencing personal exposure of pregnant women in Barcelona. To this end, indoor, outdoor and personal exposure measurements were carried out for a selection of 54 pregnant women between November 2008 and November 2009. PM2.5 samples were collected during two consecutive days and then analysed for black smoke (BS), major and trace elements, and polycyclic aromatic hydrocarbons (PAHs) concentrations. Personal information such as commuting patterns and cosmetics use was also collected. PM2.5 concentrations were higher for personal samples than for indoor and outdoor environments. Indoor, outdoor and personal BS and sulphate concentrations were strongly correlated, although some specific indoor and outdoor sulphate sources may exist. Average trace elements concentrations were similar indoor, outdoor and for personal exposure, but the correlations were moderate for most of them. Most of the PAHs concentrations showed strong correlations indoor-outdoor. A source apportionment analysis of the PM composition data by means of a Positive Matrix Factorization (PMF) resulted in the identification of six sources for the outdoor and indoor environments: secondary sulphate, fueloil + sea salt (characterized by V, Ni, Na and Mg), mineral, cigarette (characterized by K, Ce, Cd, benzo(k)fluoranthene and benzo(ghi)perylene), road traffic (characterized by BS and low weight PAHs), and industrial (characterized by Pb, Sn, Cu, Mn and Fe). For personal exposure two specific sources were found: cosmetics (characterized by abundance of Ca, Li, Ti and Sr and the absence of Al) and train/subway (characterized by Fe, Mn, Cu and Ba). The contribution of the sources varied widely among women, especially for cigarette (from zero to up to 4 μg m-3), train/subway (up to more than 6 μg m-3) and cosmetics (up to more than 5 μg m-3). The source contributions showed generally strong correlations indoor-outdoor although the infiltration efficiencies varied among homes. This study emphasizes the importance of relying on personal exposure in epidemiological studies assessing the impact of air pollution on human health.

Quantifying impacts on air quality of vehicular emissions in Sao Paulo and Rio de Janeiro

NASA Astrophysics Data System (ADS)

Artaxo, Paulo; Ferreira de Brito, Joel; Godoy, José Marcus; Luiza Godoy, Maria; Junior, Djacinto

2016-04-01

Vehicular emissions in megacities such as Sao Paulo and Rio de Janeiro are increasingly becoming a global issue. The São Paulo Metropolitan Area (SPMA), located in Southeast of Brazil, is a megacity with a population of 18 million people, with 7 million cars and large-scale industrial emissions. Rio de Janeiro is also a large city with different meteorology than São Paulo. All cars in Brazil runs gasohol, with 23% ethanol in gasoline, and for the last 10 years, flex cars that can run on gasohol, ethanol or any mixture dominate the market. Overall ethanol accounts for about 30-40% of fuel burned in both cities. To improve the understanding of vehicular emission impacts on aerosol composition and life cycle in these two large megacities a source apportionment study, combining online and offline measurements, was performed. Aerosols were collected for one year to capture seasonal variability at 4 sites in each city, with inorganic and organic aerosol component being sampled. Organic and elemental carbon were measured using a Sunset Laboratory Dual Optics (transmission and reflectance) Carbon Analyzer and about 22 trace elements has been measured using polarized X-Ray Fluorescence (XRF). Aerosol mass and black carbon were also measured, as well as trace gases to help in aerosol source apportionment. In Sao Paulo, the average PM2.5 mass concentration obtained varied from 9.6 to 12.2 μg m-3 for the several sites, and similar concentrations were measured in Rio de Janeiro. At all sites, organic matter (OM) has dominated fine mode aerosol concentration with 42 to 60% of the aerosol mass. EC accounted for 21 to 31% of fine mode aerosol mass concentration. Sulfate accounted for 21 to 26% of PM2.5 for the sites. Aerosol source apportionment was done with receptor analysis and integration with online data such as PTR-MS, Aethalometers, Nephelometers and ACSM helped to apportion vehicular emissions. For the 8 sites operated in Sao Paulo and Rio de Janeiro, vehicular emissions accounts for about 63% of PM2.5. Results are very similar for the different sites and cities.

Seasonal effect and source apportionment of polycyclic aromatic hydrocarbons in PM2.5

NASA Astrophysics Data System (ADS)

Khan, Md Firoz; Latif, Mohd Talib; Lim, Chee Hou; Amil, Norhaniza; Jaafar, Shoffian Amin; Dominick, Doreena; Mohd Nadzir, Mohd Shahrul; Sahani, Mazrura; Tahir, Norhayati Mohd

2015-04-01

This study aims to investigate distribution and sources of 16 polycyclic aromatic hydrocarbons (PAHs) bound to fine particulate matter (PM2.5) captured in a semi-urban area in Malaysia during different seasons, and to assess their health risks. PM2.5 samples were collected using a high volume air sampler on quartz filter paper at a flow rate of 1 m3 min-1 for 24 h. PAHs on the filter paper were extracted with dichloromethane (DCM) using an ultrasonic centrifuge solid-phase extraction method and measured by gas chromatography-mass spectroscopy. The results showed that the range of PAHs concentrations in the study period was between 0.21 and 12.08 ng m-3. The concentrations of PAHs were higher during the south-west monsoon (0.21-12.08 ng m-3) compared to the north-east monsoon (0.68-3.80 ng m-3). The high molecular weight (HMW) PAHs (≥5 ring) are significantly prominent (>70%) compared to the low molecular weight (LMW) PAHs (≤4 ring) in PM2.5. The Spearman correlation indicates that the LMW and HMW PAHs correlate strongly among themselves. The diagnostic ratios (DRs) of I[c]P/I[c]P + BgP and B[a]P/B[g]P suggest that the HMW PAHs originated from fuel combustion sources. The source apportionment analysis of PAHs was resolved using DRs-positive matrix factorization (PMF)-multiple linear regression (MLR). The main sources identified were (a) gasoline combustion (65%), (b) diesel and heavy oil combustion (19%) and (c) natural gas and coal burning (15%). The health risk evaluation, by means of the lifetime lung cancer risk (LLCR), showed no potential carcinogenic risk from the airborne BaPeq (which represents total PAHs at the present study area in Malaysia). The seasonal LLCR showed that the carcinogenic risk of total PAHs were two fold higher during south-westerly monsoon compared to north-easterly monsoon.

Radiocarbon determination of fossil and contemporary carbon contribution to aerosol in the Pacific Islands.

PubMed

Isley, C F; Nelson, P F; Taylor, M P; Williams, A A; Jacobsen, G E

2018-06-21

Combustion emissions are of growing concern across all Pacific Island Countries, which account for >10,000 km 2 of the earth's surface area; as for many other small island states globally. Apportioning emissions inputs for Suva, the largest Pacific Island city, will aid in development of emission reduction strategies. Total suspended particulate (TSP) and fine particulate (PM 2.5 ) samples were collected for Suva City, a residential area (Kinoya, TSP) and a mainly ocean-influenced site (Suva Point, TSP) from 2014 to 2015. Percentages of contemporary and fossil carbon were determined by radiocarbon analysis (accelerator mass spectrometry); for non‑carbonate carbon (NCC), elemental carbon (EC) and organic carbon (OC). Source contributions to particulate matter were identified and the accuracy of previous emissions inventory and source apportionment studies was evaluated. Suva Point NCC concentrations (2.7 ± 0.4 μg/m 3 ) were four times lower than for City (13 ± 2 μg/m 3 in TSP) and Kinoya (13 ± 1 μg/m 3 in TSP); demonstrating the contribution of land-based emissions activities in city and residential areas. In Suva City, total NCC in air was 81% (79%-83%) fossil carbon, from vehicles, shipping, power generation and industry; whilst in the residential area, 48% (46%-50%) of total NCC was contemporary carbon; reflecting the higher incidence of biomass and waste burning and of cooking activities. Secondary organic fossil carbon sources contributed >36% of NCC mass at the city and >29% at Kinoya; with biogenic carbon being Kinoya's most significant source (approx. 30% of NCC mass). These results support the previous source apportionment studies for the city area; yet show that, in line with emissions inventory studies, biomass combustion contributes more PM 2.5 mass in residential areas. Hence air quality management strategies need to target open burning activities as well as fossil fuel combustion. Copyright © 2018 Elsevier B.V. All rights reserved.

Source apportionment of atmospheric bulk deposition in the Belgrade urban area using Positive Matrix factorization

NASA Astrophysics Data System (ADS)

Tasić, M.; Mijić, Z.; Rajšić, S.; Stojić, A.; Radenković, M.; Joksić, J.

2009-04-01

The primary objective of the present study was to assess anthropogenic impacts of heavy metals to the environment by determination of total atmospheric deposition of heavy metals. Atmospheric depositions (wet + dry) were collected monthly, from June 2002 to December 2006, at three urban locations in Belgrade, using bulk deposition samplers. Concentrations of Fe, Al, Pb, Zn, Cu, Ni, Mn, Cr, V, As and Cd were analyzed using atomic absorption spectrometry. Based upon these results, the study attempted to examine elemental associations in atmospheric deposition and to elucidate the potential sources of heavy metal contaminants in the region by the use of multivariate receptor model Positive Matrix Factorization (PMF).

Limitation of using Angstrom exponent for source apportionment of black carbon in complex environments - A case study from the North West Indo- Gangetic plain

NASA Astrophysics Data System (ADS)

Garg, S.; Sinha, B.; Sinha, V.; Chandra, P.; Sarda Esteve, R.; Gros, V.

2015-12-01

Determining the contribution of different sources to the total BC is necessary for targeted mitigation. Absorption Angstrom exponent (αabs) measurements of black carbon (BC) have recently been introduced as a novel tool to apportion the contribution of biomass burning sources to BC. Two-component Aethalometer model for apportioning BC to biomass burning sources and fossil fuel combustion sources, which uses αabs as a generic indicator of the source type, is widely used for determining the contribution of the two types of sources to the total BC. Our work studies BC emissions in the highly-populated, anthropogenic emissions-dominated Indo-Gangetic Plain and demonstrates that the αabs cannot be used as a generic tracer for biomass burning emissions in a complex environment. Simultaneously collected high time resolution data from a 7-wavelength Aethalometer (AE 42, Magee Scientific, USA) and a high sensitivity Proton Transfer Reaction- Quadrupole Mass Spectrometer (PTR-MS) installed at a sub-urban site in Mohali (Punjab), India, were used to identify a number of biomass combustion plumes during which BC enhancements correlated strongly with an increase in acetonitrile (a well-established biomass burning tracer) mixing ratio. Each type of biomass combustion is classified and characterized by distinct emission ratios of aromatic compounds and oxygenated VOCs to acetonitrile. The identified types of biomass combustion include two different types of crop residue burning (paddy and wheat), burning of leaf-litter, and garbage burning. Traffic (fossil-fuel burning) plumes were also selected for comparison. We find that the two-component Aethalometer source-apportionment method cannot be extrapolated to all types of biomass combustion and αabs of traffic plumes can be >1 in developing countries like India, where use of adulterated fuel in vehicles is common. Thus in a complex environment, where multiple anthropogenic BC sources and air masses of variable photochemical age impact a receptor site, the angstrom exponent is not representative of the combustion type and therefore, cannot be used as a generic tracer to constrain source contributions.

Apportionment of sources of fine and coarse particles in four major Australian cities by positive matrix factorisation

NASA Astrophysics Data System (ADS)

Chan, Yiu-Chung; Cohen, David D.; Hawas, Olga; Stelcer, Eduard; Simpson, Rod; Denison, Lyn; Wong, Neil; Hodge, Mary; Comino, Eva; Carswell, Stewart

In this study, 437 days of 6-daily, 24-h samples of PM 2.5, PM 2.5-10 and PM 10 were collected over a 12-month period during 2003-2004 in Melbourne, Sydney, Brisbane and Adelaide. The elemental, ionic and polycyclic aromatic hydrocarbon composition of the particles were determined. Source apportionment was carried out by using the positive matrix factorisation software (PMF2). Eight factors were identified for the fine particle samples including 'motor vehicles', 'industry', 'other combustion sources', 'ammonium sulphates', 'nitrates', 'marine aerosols', 'chloride depleted marine aerosols' and 'crustal/soil dust'. On average combustion sources, secondary nitrates/sulphates and natural origin dust contributed about 46%, 25% and 26% of the mass of the fine particle samples, respectively. 'Crustal/soil dust', 'marine aerosols', 'nitrates' and 'road side dust' were the four factors identified for the coarse particle samples. On average natural origin dust contributed about 76% of the mass of the coarse particle samples. The contributions of the sources to the sample mass basically reflect the emission source characteristics of the sites. Secondary sulphates and nitrates were found to spread out evenly within each city. The average contribution of secondary nitrates to fine particles was found to be rather uniform in different seasons, rather than higher in winter as found in other studies. This could be due to the low humidity conditions in winter in most of the Australian cities which made the partitioning of the particle phase less favourable in the NH 4NO 3 equilibrium system. A linear relationship was found between the average contribution of marine aerosols and the distance of the site from the bay side. Wind erosion was found associated with higher contribution of crustal dust on average and episodes of elevated concentration of coarse particles in spring and summer.

Single particle mass spectral signatures from vehicle exhaust particles and the source apportionment of on-line PM2.5 by single particle aerosol mass spectrometry.

PubMed

Yang, Jian; Ma, Shexia; Gao, Bo; Li, Xiaoying; Zhang, Yanjun; Cai, Jing; Li, Mei; Yao, Ling'ai; Huang, Bo; Zheng, Mei

2017-09-01

In order to accurately apportion the many distinct types of individual particles observed, it is necessary to characterize fingerprints of individual particles emitted directly from known sources. In this study, single particle mass spectral signatures from vehicle exhaust particles in a tunnel were performed. These data were used to evaluate particle signatures in a real-world PM 2.5 apportionment study. The dominant chemical type originating from average positive and negative mass spectra for vehicle exhaust particles are EC species. Four distinct particle types describe the majority of particles emitted by vehicle exhaust particles in this tunnel. Each particle class is labeled according to the most significant chemical features in both average positive and negative mass spectral signatures, including ECOC, NaK, Metal and PAHs species. A single particle aerosol mass spectrometry (SPAMS) was also employed during the winter of 2013 in Guangzhou to determine both the size and chemical composition of individual atmospheric particles, with vacuum aerodynamic diameter (d va ) in the size range of 0.2-2μm. A total of 487,570 particles were chemically analyzed with positive and negative ion mass spectra and a large set of single particle mass spectra was collected and analyzed in order to identify the speciation. According to the typical tracer ions from different source types and classification by the ART-2a algorithm which uses source fingerprints for apportioning ambient particles, the major sources of single particles were simulated. Coal combustion, vehicle exhaust, and secondary ion were the most abundant particle sources, contributing 28.5%, 17.8%, and 18.2%, respectively. The fraction with vehicle exhaust species particles decreased slightly with particle size in the condensation mode particles. Copyright © 2017 Elsevier B.V. All rights reserved.

SOURCE APPORTIONMENT OF FINE PARTICULATE MATTER BY CLUSTERING SINGLE-PARTICLE DATA: TESTS OF RECEPTOR MODEL ACCURACY. (R826371C001)

EPA Science Inventory

The perspectives, information and conclusions conveyed in research project abstracts, progress reports, final reports, journal abstracts and journal publications convey the viewpoints of the principal investigator and may not represent the views and policies of ORD and EPA. Concl...

SOURCE APPORTIONMENT OF PRIMARY CARBONACEOUS AEROSOL USING THE COMMUNITY MULTISCALE AIR QUALITY MODEL

EPA Science Inventory

A substantial fraction of fine particulate matter (PM) across the United States is composed of carbon, which may be either emitted in particulate form (i.e., primary) or formed in the atmosphere through gas-to-particle conversion processes (i.e., secondary). Primary carbonaceous...

SOURCE APPORTIONMENT OF PRIMARY AND SECONDARY CARBONACEOUS AEROSOL IN THE UNITED STATES USING MODELS AND MEASUREMENTS

EPA Science Inventory

In this presentation, three diagnostic evaluation methods of model performance for carbonaceous aerosol are reviewed. The EC-tracer method is used to distinguish primary and secondary carbon, radiocarbon data are used to distinguish fossil-fuel and contemporary carbon, and organ...

Large contribution of fossil fuel derived secondary organic carbon to water soluble organic aerosols in winter haze in China

NASA Astrophysics Data System (ADS)

Zhang, Yan-Lin; El-Haddad, Imad; Huang, Ru-Jin; Ho, Kin-Fai; Cao, Jun-Ji; Han, Yongming; Zotter, Peter; Bozzetti, Carlo; Daellenbach, Kaspar R.; Slowik, Jay G.; Salazar, Gary; Prévôt, André S. H.; Szidat, Sönke

2018-03-01

Water-soluble organic carbon (WSOC) is a large fraction of organic aerosols (OA) globally and has significant impacts on climate and human health. The sources of WSOC remain very uncertain in polluted regions. Here we present a quantitative source apportionment of WSOC, isolated from aerosols in China using radiocarbon (14C) and offline high-resolution time-of-flight aerosol mass spectrometer measurements. Fossil emissions on average accounted for 32-47 % of WSOC. Secondary organic carbon (SOC) dominated both the non-fossil and fossil derived WSOC, highlighting the importance of secondary formation to WSOC in severe winter haze episodes. Contributions from fossil emissions to SOC were 61 ± 4 and 50 ± 9 % in Shanghai and Beijing, respectively, significantly larger than those in Guangzhou (36 ± 9 %) and Xi'an (26 ± 9 %). The most important primary sources were biomass burning emissions, contributing 17-26 % of WSOC. The remaining primary sources such as coal combustion, cooking and traffic were generally very small but not negligible contributors, as coal combustion contribution could exceed 10 %. Taken together with earlier 14C source apportionment studies in urban, rural, semi-urban and background regions in Asia, Europe and the USA, we demonstrated a dominant contribution of non-fossil emissions (i.e., 75 ± 11 %) to WSOC aerosols in the Northern Hemisphere; however, the fossil fraction is substantially larger in aerosols from East Asia and the eastern Asian pollution outflow, especially during winter, due to increasing coal combustion. Inclusion of our findings can improve a modelling of effects of WSOC aerosols on climate, atmospheric chemistry and public health.

Comparison of PM10 concentrations and metal content in three different sites of the Venice Lagoon: an analysis of possible aerosol sources.

PubMed

Contini, Daniele; Belosi, Franco; Gambaro, Andrea; Cesari, Daniela; Stortini, Angela Maria; Bove, Maria Chiara

2012-01-01

The Venice Lagoon is exposed to atmospheric pollutants from industrial activities, thermoelectric power plants, petrochemical plants, incinerator, domestic heating, ship traffic, glass factories and vehicular emissions on the mainland. In 2005, construction began on the mobile dams (MOSE), one dam for each channel connecting the lagoon to the Adriatic Sea as a barrier against high tide. These construction works could represent an additional source of pollutants. PM10 samples were taken on random days between 2007 and 2010 at three different sites: Punta Sabbioni, Chioggia and Malamocco, located near the respective dam construction worksites. Chemical analyses of V, Cr, Fe, Co, Ni, Cu, Zn, As, Mo, Cd, Sb, Tl and Pb in PM10 samples were performed by Inductively coupled plasma-quadrupole mass spectrometry (ICP-QMS) and results were used to identify the main aerosol sources. The correlation of measured data with meteorology, and source apportionment, failed to highlight a contribution specifically associated to the emissions of the MOSE construction works. The comparison of the measurements at the three sites showed a substantial homogeneity of metal concentrations in the area. Source apportionment with principal component analysis (PCA) and positive matrix factorization (PMF) showed that a four principal factors model could describe the sources of metals in PM10. Three of them were assigned to specific sources in the area and one was characterised as a source of mixed origin (anthropogenic and crustal). A specific anthropogenic source of PM10 rich in Ni and Cr, active at the Chioggia site, was also identified.

Source apportionment of size-fractionated particles during the 2013 Asian Youth Games and the 2014 Youth Olympic Games in Nanjing, China.

PubMed

Chen, Pulong; Wang, Tijian; Lu, Xiaobo; Yu, Yiyong; Kasoar, Matthew; Xie, Min; Zhuang, Bingliang

2017-02-01

In this study, samples of size-fractionated particulate matter were collected continuously using a 9-size interval cascade impactor at an urban site in Nanjing, before, during and after the Asian Youth Games (AYG), from July to September of 2013, and the Youth Olympic Games (YOG), from July to September of 2014. First, elemental concentrations, water-soluble ions including Cl - , NO 3 - , SO 4 2- , NH 4 + , K + , Na + and Ca 2+ , organic carbon (OC) and elemental carbon (EC) were analysed. Then, the source apportionment of the fine and coarse particulate matter was carried out using the chemical mass balance (CMB) model. The average PM 10 concentrations were 90.4±20.0μg/m 3 during the 2013 AYG and 70.6±25.3μg/m 3 during the 2014 YOG. For PM 2.1, the average concentrations were 50.0±12.8μg/m 3 in 2013 and 34.6±17.0μg/m 3 in 2014. Investigations showed that the average concentrations of particles declined significantly from 2013 to 2014, and concentrations were at the lowest levels during the events. Results indicated that OC, EC, sulfate and crustal elements have significant monthly and size-based variations. The major components, including crustal elements, water-soluble ions and carbonaceous aerosol accounted for 75.3-91.9% of the total particulate mass concentrations during the sampling periods. Fugitive dust, coal combustion dust, iron dust, construction dust, soil dust, vehicle exhaust, secondary aerosols and sea salt have been classified as the main emissions in Nanjing. The source apportionment results indicate that the emissions from fugitive dust, which was the most abundance emission source during the 2013 AYG, contributed to 23.0% of the total particle mass. However, fugitive dust decreased to 6.2% of the total particle mass during the 2014 YOG. Construction dust (14.7% versus 7.8% for the AYG and the YOG, respectively) and secondary sulfate aerosol (9.3% versus 8.0% for the AYG and the YOG, respectively) showed the same trend as fugitive dust, suggesting that the mitigation measures of controlling particles from the paved roads, construction and industry worked more efficiently during the YOG. Copyright © 2016 Elsevier B.V. All rights reserved.

Organophosphate ester flame retardants in Nepalese soil: Spatial distribution, source apportionment and air-soil exchange assessment.

PubMed

Yadav, Ishwar Chandra; Devi, Ningombam Linthoingambi; Li, Jun; Zhang, Gan

2018-01-01

Despite soil being the major terrestrial environmental reservoir and one of the significant sinks for many hydrophobic organic compounds including organophosphate ester flame retardants (OPFRs), limited information is available about concentration and fate of OPFRs contamination in urban soil in general and especially in case of Nepal. This study investigates the environmental concentration, spatial distribution and source apportionment of eight OPFRs in surface soil (n = 28) from four major cities of Nepal with special interest on air-soil exchange. Overall, significantly high concentrations of ∑ 8 OPFR were measured in soil ranging from 25-27,900 ng/g dw (median 248 ng/g dw). In terms of compositional pattern, tris(methyl phenyl) phosphate (TMPP) was the most abundant phosphorus chemical in soil, followed by tris(2-chloroisopropyl) phosphate (TCIPP), and accounted for 35-49% and 8-25% of ∑ 8 OPFRs, respectively. The high level of these OPFRs was attributed to local sources as opposed to transboundary influence from remote areas. A Spearman's rank correlation analysis exhibited weak correlation of ∑ 8 OPFRs with TOC (Rho = 0.117, p < 0.05) and BC (Rho = 0.007, p < 0.05), suggesting little or no influence of TOC and BC on the concentration of ∑ 8 OPFRs. The fugacity fraction (ff) results indicated a strong influence of soil contamination on atmospheric level of OPFRs via volatilization. Copyright © 2017 Elsevier Ltd. All rights reserved.

The ambient aerosol characterization during the prescribed bushfire season in Brisbane 2013.

PubMed

Milic, A; Miljevic, B; Alroe, J; Mallet, M; Canonaco, F; Prevot, A S H; Ristovski, Z D

2016-08-01

Prescribed burnings are conducted in Queensland each year from August until November aiming to decrease the impact of bushfire hazards and maintain the health of vegetation. This study reports chemical characteristics of the ambient aerosol, with a focus on source apportionment of the organic aerosol (OA) fraction, during the prescribed biomass burning (BB) season in Brisbane 2013. All measurements were conducted within the International Laboratory for Air Quality and Health (ILAQH) located in Brisbane's Central Business District. Chemical composition, degree of ageing and the influence of BB emission on the air quality of central Brisbane were characterized using a compact Time of Flight Aerosol Mass Spectrometer (cToF-AMS). AMS loadings were dominated by OA (64%), followed by, sulfate (17%), ammonium (14%) and nitrates (5%). Source apportionment was applied on the AMS OA mass spectra via the multilinear engine solver (ME-2) implementation within the recently developed Source Finder (SoFi) interface. Six factors were extracted including hydrocarbon-like OA (HOA), cooking-related OA (COA), biomass burning OA (BBOA), low-volatility oxygenated OA (LV-OOA), semivolatile oxygenated OA (SV-OOA), and nitrogen-enriched OA (NOA). The aerosol fraction that was attributed to BB factor was 9%, on average over the sampling period. The high proportion of oxygenated OA (72%), typically representing aged emissions, could possess a fraction of oxygenated species transfored from BB components on their way to the sampling site. Copyright © 2016 Elsevier B.V. All rights reserved.

Organic aerosol source apportionment in London 2013 with ME-2: exploring the solution space with annual and seasonal analysis

NASA Astrophysics Data System (ADS)

Reyes-Villegas, Ernesto; Green, David C.; Priestman, Max; Canonaco, Francesco; Coe, Hugh; Prévôt, André S. H.; Allan, James D.

2016-12-01

The multilinear engine (ME-2) factorization tool is being widely used following the recent development of the Source Finder (SoFi) interface at the Paul Scherrer Institute. However, the success of this tool, when using the a value approach, largely depends on the inputs (i.e. target profiles) applied as well as the experience of the user. A strategy to explore the solution space is proposed, in which the solution that best describes the organic aerosol (OA) sources is determined according to the systematic application of predefined statistical tests. This includes trilinear regression, which proves to be a useful tool for comparing different ME-2 solutions. Aerosol Chemical Speciation Monitor (ACSM) measurements were carried out at the urban background site of North Kensington, London from March to December 2013, where for the first time the behaviour of OA sources and their possible environmental implications were studied using an ACSM. Five OA sources were identified: biomass burning OA (BBOA), hydrocarbon-like OA (HOA), cooking OA (COA), semivolatile oxygenated OA (SVOOA) and low-volatility oxygenated OA (LVOOA). ME-2 analysis of the seasonal data sets (spring, summer and autumn) showed a higher variability in the OA sources that was not detected in the combined March-December data set; this variability was explored with the triangle plots f44 : f43 f44 : f60, in which a high variation of SVOOA relative to LVOOA was observed in the f44 : f43 analysis. Hence, it was possible to conclude that, when performing source apportionment to long-term measurements, important information may be lost and this analysis should be done to short periods of time, such as seasonally. Further analysis on the atmospheric implications of these OA sources was carried out, identifying evidence of the possible contribution of heavy-duty diesel vehicles to air pollution during weekdays compared to those fuelled by petrol.

Interpreting stream sediment fingerprints against primary and secondary source signatures in agricultural catchments

NASA Astrophysics Data System (ADS)

Blake, Will H.; Haley, Steve; Smith, Hugh G.; Taylor, Alex; Goddard, Rupert; Lewin, Sean; Fraser, David

2013-04-01

Many sediment fingerprinting studies adopt a black box approach to source apportionment whereby the properties of downstream sediment are compared quantitatively to the geochemical fingerprints of potential catchment sources without consideration of potential signature development or modification during transit. Working within a source-pathway-receptor framework, this study aimed to undertake sediment source apportionment within 6 subcatchments of an agricultural river basin with specific attention to the potential role of contaminants (vehicle emissions and mine waste) in development of stream sediment signatures. Fallout radionuclide (FRN) and geochemical fingerprinting methods were adopted independently to establish source signatures for primary sediment sources of surface and subsurface soil materials under various land uses plus reworked mine and 'secondary' soil material deposited, in transit, along road networks. FRN data demonstrated expected variability between surface soil (137Cs = 14 ± 3 Bq kg-1; 210Pbxs = 40 ± 7 Bq kg-1) and channel bank materials (137Cs = 3 ± 1 Bq kg-1; 210Pbxs = 24 ± 5 Bq kg-1) but road transported soil material was considerably elevated in 210Pbxs (up to 673 ± 51 Bq kg-1) due to sediment interaction with pluvial surface water within the road network. Geochemical discrimination between surface and subsurface soil materials was dominated by alkaline earth and alkali metals e.g. Ba, Rb, Ca, K, Mg which are sensitive to weathering processes in soil. Magnetic susceptibility and heavy metals were important discriminators of road transported material which demonstrated transformation of the signatures of material transported via the road network. Numerical unmixing of stream sediment indicated that alongside channel bank erosion, road transported material was an important component in some systems in accord with FRN evidence. While mining spoil also ranked as a significant source in an affected catchment, perhaps related to legacy sediment, the potential role of dissolved metal leaching and subsequent sediment-water interaction within the channel on signature modification remained unclear. Consideration of sediment signature modification en route from primary source to stream elucidated important information regarding sediment transfer pathways and dynamics relevant to sediment management decisions. Further work on sediment-water interactions and potential for signature transformation in the channel environment is required.

StreamVOC - A deterministic source-apportionment model to estimate volatile organic compound concentrations in rivers and streams

USGS Publications Warehouse

Asher, William E.; Bender, David A.; Zogorski, John S.; Bartholomay, Roy C.

2006-01-01

This report documents the construction and verification of the model, StreamVOC, that estimates (1) the time- and position-dependent concentrations of volatile organic compounds (VOCs) in rivers and streams as well as (2) the source apportionment (SA) of those concentrations. The model considers how different types of sources and loss processes can act together to yield a given observed VOC concentration. Reasons for interest in the relative and absolute contributions of different sources to contaminant concentrations include the need to apportion: (1) the origins for an observed contamination, and (2) the associated human and ecosystem risks. For VOCs, sources of interest include the atmosphere (by absorption), as well as point and nonpoint inflows of VOC-containing water. Loss processes of interest include volatilization to the atmosphere, degradation, and outflows of VOC-containing water from the stream to local ground water. This report presents the details of StreamVOC and compares model output with measured concentrations for eight VOCs found in the Aberjona River at Winchester, Massachusetts. Input data for the model were obtained during a synoptic study of the stream system conducted July 11-13, 2001, as part of the National Water-Quality Assessment (NAWQA) Program of the U.S. Geological Survey. The input data included a variety of basic stream characteristics (for example, flows, temperature, and VOC concentrations). The StreamVOC concentration results agreed moderately well with the measured concentration data for several VOCs and provided compound-dependent SA estimates as a function of longitudinal distance down the river. For many VOCs, the quality of the agreement between the model-simulated and measured concentrations could be improved by simple adjustments of the model input parameters. In general, this study illustrated: (1) the considerable difficulty of quantifying correctly the locations and magnitudes of ground-water-related sources of contamination in streams; and (2) that model-based estimates of stream VOC concentrations are likely to be most accurate when the major sources are point sources or tributaries where the spatial extent and magnitude of the sources are tightly constrained and easily determined.

Friday Harbor Marina Expansion Study--San Juan Island, Washington: Final Detailed Project Report and Environmental Assessment.

DTIC Science & Technology

1981-04-01

pollutants from the marina is the leaching of heavy metals and hydrocarbons from various antifouling paints used on boats. Contamination also occurs from...by pleasure boat, placing a heavy demand on moorage and services in the marina and at the town, providing a major source of income for the area. One...First Cost 4-10 d. Cost Apportionment 4-13 SECTION 5. COORDINATION 5.01 Coordination Framework 5-1 5.02 Coordination With Key Agencies 5-1 a

Defense Coastal/Estuarine Research Program (DCERP) Baseline Monitoring Plan

DTIC Science & Technology

2007-09-19

climatological stress (e.g., temperature, drought) and shorter-term air pollutant stress (oxidants and metals ). Heavy metals of fine PM have been...speciation of the fine and coarse PM fractions will allow distinction between different PM sources such as wind blown soil dust, including dust...emitting 12% of the total PM2.5 mass (U.S. EPA, 2004b). Source apportionment modeling of PM2.5 mass concentrations from 24 Speciation Defense Coastal

Evaluation and Source Apportionment of Heavy Metals (HMs) in Sewage Sludge of Municipal Wastewater Treatment Plants (WWTPs) in Shanxi, China

PubMed Central

Duan, Baoling; Liu, Fenwu; Zhang, Wuping; Zheng, Haixia; Zhang, Qiang; Li, Xiaomei; Bu, Yushan

2015-01-01

Heavy metals (HMs) in sewage sludge have become the crucial limiting factors for land use application. Samples were collected and analyzed from 32 waste water treatment plants (WWTPs) in the Shanxi Province, China. HM levels in sewage sludge were assessed. The multivariate statistical method principal component analysis (PCA) was applied to identify the sources of HMs in sewage sludge. HM pollution classes by geochemical accumulation index Igeo and correlation analyses between HMs were also conducted. HMs were arranged in the following decreasing order of mean concentration: Zn > Cu > Cr > Pb > As > Hg > Cd; the maximum concentrations of all HMs were within the limit of maximum content permitted by Chinese discharge standard. Igeo classes of HMs pollution in order from most polluted to least were: Cu and Hg pollution were the highest; Cd and Cr pollution were moderate; Zn, As and Pb pollution were the least. Sources of HM contamination in sewage sludge were identified as three components. The primary contaminant source accounting for 35.7% of the total variance was identified as smelting industry, coking plant and traffic sources; the second source accounting for 29.0% of the total variance was distinguished as household and water supply pollution; the smallest of the three sources accounting for 16.2% of the total variance was defined as special industries such as leather tanning, textile manufacturing and chemical processing industries. Source apportionment of HMs in sewage sludge can control HM contamination through suggesting improvements in government policies and industrial processes. PMID:26690464

Evaluation and Source Apportionment of Heavy Metals (HMs) in Sewage Sludge of Municipal Wastewater Treatment Plants (WWTPs) in Shanxi, China.

PubMed

Duan, Baoling; Liu, Fenwu; Zhang, Wuping; Zheng, Haixia; Zhang, Qiang; Li, Xiaomei; Bu, Yushan

2015-12-11

Heavy metals (HMs) in sewage sludge have become the crucial limiting factors for land use application. Samples were collected and analyzed from 32 waste water treatment plants (WWTPs) in the Shanxi Province, China. HM levels in sewage sludge were assessed. The multivariate statistical method principal component analysis (PCA) was applied to identify the sources of HMs in sewage sludge. HM pollution classes by geochemical accumulation index I(geo) and correlation analyses between HMs were also conducted. HMs were arranged in the following decreasing order of mean concentration: Zn > Cu > Cr > Pb > As > Hg > Cd; the maximum concentrations of all HMs were within the limit of maximum content permitted by Chinese discharge standard. I(geo) classes of HMs pollution in order from most polluted to least were: Cu and Hg pollution were the highest; Cd and Cr pollution were moderate; Zn, As and Pb pollution were the least. Sources of HM contamination in sewage sludge were identified as three components. The primary contaminant source accounting for 35.7% of the total variance was identified as smelting industry, coking plant and traffic sources; the second source accounting for 29.0% of the total variance was distinguished as household and water supply pollution; the smallest of the three sources accounting for 16.2% of the total variance was defined as special industries such as leather tanning, textile manufacturing and chemical processing industries. Source apportionment of HMs in sewage sludge can control HM contamination through suggesting improvements in government policies and industrial processes.

Assessment of eutrophication in estuaries: Pressure-state-response and source apportionment

Treesearch

David Whitall; Suzanne Bricker

2006-01-01

The National Estuarine Eutrophication Assessment (NEEA) Update Program is a management oriented program designed to improve monitoring and assessment efforts through the development of type specific classification of estuaries that will allow improved assessment methods and development of analytical and research models and tools for managers which will help guide and...

26 CFR 1.863-3 - Allocation and apportionment of income from certain sales of inventory.

Code of Federal Regulations, 2010 CFR

2010-04-01

... income from sources within and without the United States determined under the 50/50 method. Research and... Possession Purchase Sales—(A) Business activity method. Gross income from Possession Purchase Sales is... from Possession Purchase Sales computed under the business activity method, the amounts of expenses...

Quantification and source apportionment of the methane emission flux from the city of Indianapolis

USDA-ARS?s Scientific Manuscript database

We report the CH4 emission flux from the city of Indianapolis, IN, the site of the Indianapolis Flux Experiment (INFLUX) project for developing, assessing, and improving top-down and bottom-up approaches for quantifying urban greenhouse gas emissions. Using an aircraft-based mass balance approach, w...

SOURCE APPORTIONMENT OF SEATTLE PM 2.5: A COMPARISON OF IMPROVE AND ENHANCED STN DATA SETS

EPA Science Inventory

Seattle, WA, STN and IMPROVE data sets with STN temperature resolved carbon peaks were analyzed with both the PMF and Unmix receptor models. In addition, the IMPROVE trace element data was combined with the major STN species to examine the role of IMPROVE metals. To compare the ...

Source apportionment of surface ozone in the Yangtze River Delta, China in the summer of 2013

NASA Astrophysics Data System (ADS)

Li, L.; An, J. Y.; Shi, Y. Y.; Zhou, M.; Yan, R. S.; Huang, C.; Wang, H. L.; Lou, S. R.; Wang, Q.; Lu, Q.; Wu, J.

2016-11-01

We applied ozone source apportionment technology (OSAT) with tagged tracers coupled within the Comprehensive Air Quality Model with Extensions (CAMx) to study the region and source category contribution to surface ozone in the Yangtze River Delta area in summer of 2013. Results indicate that the daytime ozone concentrations in the YRD region are influenced by emissions both locally, regionally and super-regionally. At urban Shanghai, Hangzhou and Suzhou receptors, the ozone formation is mainly VOC-limited, precursor emissions form Zhejiang province dominate their O3 concentrations. At the junction area among two provinces and Shanghai city, the ozone is usually influenced by all the three areas. The daily max O3 at the Dianshan Lake in July are contributed by Zhejiang (48.5%), Jiangsu (11.7%), Anhui (11.6%) and Shanghai (7.4%), long-range transport constitutes around 20.9%. At Chongming site, the BVOC emissions rate is higher than urban region. Regional contribution results show that Shanghai constitutes 15.6%, Jiangsu contributes 16.2% and Zhejiang accounts for 25.5% of the daily max O3. The analysis of the source category contribution to high ozone in the Yangtze River Delta region indicates that the most significant anthropogenic emission source sectors contributing to O3 pollution include industry, vehicle exhaust, although the effects vary with source sector and selected pollution episodes. Emissions of NOx and VOCs emitted from the fuel combustion of industrial boilers and kilns, together with VOCs emissions from industrial process contribute a lot to the high concentrations in urban Hangzhou, Suzhou and Shanghai. The contribution from regional elevated power plants cannot be neglected, especially to Dianshan Lake. Fugitive emissions of volatile pollution sources also have certain contribution to regional O3. These results indicate that the regional collaboration is of most importance to reduce ambient ozone pollution, particularly during high ozone episodes.

A systematic analysis of PM2.5 in Beijing and its sources from 2000 to 2012

NASA Astrophysics Data System (ADS)

Lv, Baolei; Zhang, Bin; Bai, Yuqi

2016-01-01

Particulate matter with an aerodynamic diameter of 2.5 μm or less (PM2.5) is the main air pollutant in Beijing. To have a comprehensive understanding of concentrations, compositions and sources of PM2.5 in Beijing, recent studies reporting ground-based observations and source apportionment results dated from 2000 to 2012 in this typical large city of China are reviewed. Statistical methods were also used to better enable data comparison. During the last decade, annual average concentrations of PM2.5 have decreased and seasonal mean concentrations declined through autumn and winter. Generally, winter is the most polluted season and summer is the least polluted one. Seasonal variance of PM2.5 levels decreased. For diurnal variance, PM2.5 generally increases at night and decreases during the day. On average, organic matters, sulfate, nitrate and ammonium are the major compositions of PM2.5 in Beijing. Fractions of organic matters increased from 2000 to 2004, and decreased afterwards. Fractions of sulfate, nitrate and ammonium decreased in winter and remained largely unchanged in summer. Concentrations of organic carbon and elemental carbon were always higher in winter than in summer and they barely changed during the last decade. Concentrations of sulfate, nitrate and ammonium exhibited significant increasing trend in summer but in reverse in winter. On average they were higher in winter than in summer before 2005, and took a reverse after 2005. Receptor model results show that vehicle, dust, industry, biomass burning, coal combustion and secondary products were major sources and they all increased except coal combustions and secondary products. The growth was decided both changing social and economic activities in Beijing, and most likely growing emissions in neighboring Hebei province. Explicit descriptions of the spatial variations of PM2.5 concentration, better methods to estimate secondary products and ensemble source apportionments models to reduce uncertainties would remain being open questions for future studies.

PM₁₀ and PM₂.₅ sources at an insular location in the western Mediterranean by using source apportionment techniques.

PubMed

Pey, Jorge; Alastuey, Andrés; Querol, Xavier

2013-07-01

PM₁₀ and PM₂.₅ chemical composition has been determined at a suburban insular site in the Balearic Islands (Spain) during almost one and a half year. As a result, 200 samples with more than 50 chemical parameters analyzed have been obtained. The whole database has been analyzed by two receptor modelling techniques (Principal Component Analysis and Positive Matrix Factorisation) in order to identify the main PM sources. After that, regression analyses with respect to the PM mass concentrations were conducted to quantify the daily contributions of each source. Four common sources were identified by both receptor models: secondary nitrate coupled with vehicular emissions, secondary sulphate influenced by fuel-oil combustion, aged marine aerosols and mineral dust. In addition, PCA isolated harbour emissions and a mixed anthropogenic factor containing industrial emissions; whereas PMF isolated an additional mineral factor interpreted as road dust+harbour emissions, and a vehicular abrasion products factor. The use of both methodologies appeared complementary. Nevertheless, PMF sources by themselves were better differentiated. Besides these receptor models, a specific methodology to quantify African dust was also applied. The combination of these three source apportionment tools allowed the identification of 8 sources, being 4 of them mineral (African, regional, urban and harbour dusts). As a summary, 29% of PM₁₀ was attributed to natural sources (African dust, regional dust and sea spray), whereas the proportion diminished to 11% in PM₂.₅. Furthermore, the secondary sulphate source, which accounted for about 22 and 32% of PM₁₀ and PM₂.₅, is strongly linked to the aged polluted air masses residing over the western Mediterranean in the warm period. Copyright © 2013 Elsevier B.V. All rights reserved.

Source-sector contributions to European ozone and fine PM in 2010 using AQMEII modeling data

NASA Astrophysics Data System (ADS)

Karamchandani, Prakash; Long, Yoann; Pirovano, Guido; Balzarini, Alessandra; Yarwood, Greg

2017-05-01

Source apportionment modeling provides valuable information on the contributions of different source sectors and/or source regions to ozone (O3) or fine particulate matter (PM2.5) concentrations. This information can be useful in designing air quality management strategies and in understanding the potential benefits of reducing emissions from a particular source category. The Comprehensive Air quality Model with Extensions (CAMx) offers unique source attribution tools, called the Ozone and Particulate Source Apportionment Technology (OSAT/PSAT), which track source contributions. We present results from a CAMx source attribution modeling study for a summer month and a winter month using a recently evaluated European CAMx modeling database developed for Phase 3 of the Air Quality Model Evaluation International Initiative (AQMEII). The contributions of several source sectors (including model boundary conditions of chemical species representing transport of emissions from outside the modeling domain as well as initial conditions of these species) to O3 or PM2.5 concentrations in Europe were calculated using OSAT and PSAT, respectively. A 1-week spin-up period was used to reduce the influence of initial conditions. Evaluation focused on 16 major cities and on identifying source sectors that contributed above 5 %. Boundary conditions have a large impact on summer and winter ozone in Europe and on summer PM2.5, but they are only a minor contributor to winter PM2.5. Biogenic emissions are important for summer ozone and PM2.5. The important anthropogenic sectors for summer ozone are transportation (both on-road and non-road), energy production and conversion, and industry. In two of the 16 cities, solvent and product also contributed above 5 % to summertime ozone. For summertime PM2.5, the important anthropogenic source sectors are energy, transportation, industry, and agriculture. Residential wood combustion is an important anthropogenic sector in winter for PM2.5 over most of Europe, with larger contributions in central and eastern Europe and the Nordic cities. Other anthropogenic sectors with large contributions to wintertime PM2.5 include energy, transportation, and agriculture.

Identification and chemical characterization of industrial particulate matter sources in southwest Spain.

PubMed

Alastuey, Andrés; Querol, Xavier; Plana, Feliciano; Viana, Mar; Ruiz, Carmen R; Sánchez de la Campa, Ana; de la Rosa, Jesús; Mantilla, Enrique; García dos Santos, Saul

2006-07-01

A detailed physical and chemical characterization of coarse particulate matter (PM10) and fine particulate matter (PM2.5) in the city of Huelva (in Southwestern Spain) was carried out during 2001 and 2002. To identify the major emission sources with a significant influence on PM10 and PM2.5, a methodology was developed based on the combination of: (1) real-time measurements of levels of PM10, PM2.5, and very fine particulate matter (PM1); (2) chemical characterization and source apportionment analysis of PM10 and PM2.5; and (3) intensive measurements in field campaigns to characterize the emission plumes of several point sources. Annual means of 37, 19, and 16 microg/m3 were obtained for the study period for PM10, PM2.5, and PM1, respectively. High PM episodes, characterized by a very fine grain size distribution, are frequently detected in Huelva mainly in the winter as the result of the impact of the industrial emission plumes on the city. Chemical analysis showed that PM at Huelva is characterized by high PO4(3-) and As levels, as expected from the industrial activities. Source apportionment analyses identified a crustal source (36% of PM10 and 31% of PM2.5); a traffic-related source (33% of PM10 and 29% of PM2.5), and a marine aerosol contribution (only in PM10, 4%). In addition, two industrial emission sources were identified in PM10 and PM2.5: (1) a petrochemical source, 13% in PM10 and 8% in PM2.5; and (2) a mixed metallurgical-phosphate source, which accounts for 11-12% of PM10 and PM2.5. In PM2.5 a secondary source has been also identified, which contributed to 17% of the mass. A complete characterization of industrial emission plumes during their impact on the ground allowed for the identification of tracer species for specific point sources, such as petrochemical, metallurgic, and fertilizer and phosphate production industries.

Advanced receptor modelling for the apportionment of road dust resuspension to atmospheric PM

NASA Astrophysics Data System (ADS)

Amato, F.; Pandolfi, M.; Escrig, A.; Querol, X.; Alastuey, A.; Pey, J.; Perez, N.; Hopke, P. K.

2009-04-01

Fugitive emissions from traffic resuspension can often represent an important source of atmospheric particulate matter in urban environments, especially when the scarce precipitations favour the accumulation of road dust. Resuspension of road dust can lead to high exposures to heavy metals, metalloids and mineral matter. Knowing the amount of its contribution to atmospheric PM is a key task for establishing eventual mitigation or preventive measures. Factor analysis techniques are widely used tools for atmospheric aerosol source apportionment, based on the mass conservation principle. Paatero and Tapper (1993) suggested the use of a Weighted Least Squares scheme with the aim of obtaining a minimum variance solution. Additionally they proposed to incorporate the basic physical constraint of non negativity, calling their approach Positive Matrix Factorization (PMF), which can be performed by the program PMF2 released by Paatero (1997). Nevertheless, Positive Matrix Factorization can be either solved with the Multilinear Engine (ME-2), a more flexible program, also developed by Paatero (1999), which can solve any model consisting in sum of products of unknowns. The main difference with PMF2 is that ME-2 does not solve only well-defined tasks, but its actions are defined in a "script file" written in a special-purpose programming language, allowing incorporating additional tasks such as data processing etc. Thus in ME-2 a priori information, e.g. chemical fingerprints can be included as auxiliary terms of the object function to be minimized. This feature of ME-2 make it especially suitable for source apportionment studies where some knowledge (chemical ratios, profiles, mass conservation etc) of involved sources is available. The aim of this study was to quantify the contribution of road dust resuspension in PM10, PM2.5 and PM1 data set from Barcelona (Spain). Given that recently the emission profile of local road dust was characterized (Amato et al., in press), authors show how to apply in ME-2 this knowledge to obtain a quantitative assessment of this source. The achievement of this objective permitted to show how is possible to improve a basic solution of PMF2 basing on an extended model. Results show that road dust resuspension accounted for 6.7 µg/m3 (16%) in PM10, 2.2 µg/m3 (8%) of PM2.5 and 0.3 µg/m3 (1%) of PM1, revealing that fugitive emissions were responsible of the 36%, 18% and 2% of total traffic emissions respectively in PM10, PM2.5 and PM1. Acknowledments: This work was funded by the Spanish Ministry of Science and Innovation (GRACCIE-SCD2007-00067)

Development of a chemical source apportionment decision support framework for lake catchment management.

PubMed

Comber, Sean D W; Smith, Russell; Daldorph, Peter; Gardner, Michael J; Constantino, Carlos; Ellor, Brian

2018-05-01

Increasing pressures on natural resources has led to the adoption of water quality standards to protect ecological and human health. Lakes and reservoirs are particularly vulnerable to pressure on water quality owing to long residence times compared with rivers. This has raised the question of how to determine and to quantify the sources of priority chemicals (e.g. nutrients, persistent organic pollutants and metals) so that suitable measures can be taken to address failures to comply with regulatory standards. Contaminants enter lakes waters from a range of diffuse and point sources. Decision support tools and models are essential to assess the relative magnitudes of these sources and to estimate the impacts of any programmes of measures. This paper describes the development and testing of the Source Apportionment Geographical Information System (SAGIS) for future management of 763 lakes in England and Wales. The model uses readily available national data sets to estimate contributions of a number of key chemicals including nutrients (nitrogen and phosphorus), metals (copper, zinc, cadmium, lead, mercury and nickel) and organic chemicals (Polynuclear Aromatic Hydrocarbons) from multiple sector sources. Lake-specific sources are included (groundbait from angling and bird faeces) and hydrology associated with pumped inputs and abstraction. Validation data confirms the efficacy of the model to successfully predicted seasonal patterns of all types of contaminant concentrations under a number of hydrological scenarios. Such a tool has not been available on a national scale previously for such a wide range of chemicals and is currently being used to assist with future river basin planning. Copyright © 2017 Elsevier B.V. All rights reserved.

Source apportionment and water solubility of metals in size segregated particles in urban environments.

PubMed

Jiang, Sabrina Yanan; Kaul, Daya S; Yang, Fenhuan; Sun, Li; Ning, Zhi

2015-11-15

Metals in atmospheric particulate matter (PM) have been associated with various adverse health effects. Different factors contributing to the characterization and distribution of atmospheric metals in urban environments lead to uncertainty of the understanding of their impact on public health. However, few studies have provided a comprehensive picture of the spatial and seasonal variability of metal concentration, solubility and size distribution, all of which have important roles in their contribution to health effects. This study presents an experimental investigation on the characteristics of metals in PM2.5 and coarse PM in two seasons from four urban sites in Hong Kong. The PM samples were extracted separately with aqua regia and water, and a total of sixteen elements were analyzed using ICP-MS and ICP-OES to determine the size segregated concentration and solubility of metals. The concentrations of major metals were distributed in similar patterns with the same order of magnitude among different urban sites. Source apportionment using Positive Matrix Factorization (PMF) indicated that three sources namely road dust, vehicular exhaust and ship emission are major contributors to the urban atmospheric metal concentrations in Hong Kong with distinctly different profiles between coarse PM and PM2.5 fractions. The individual metals were assigned to different sources, consistent with literature documentation, except potassium emerging with substantial contribution from vehicle exhaust emission. Literature data from past studies on both local and other cities were compared to the results from the present study to investigate the impact of different emission sources and control policies on metal distribution in urban atmosphere. A large variation of solubility among the metals reflected that the majority of metals in PM2.5 were more soluble than those in coarse PM indicating size dependent chemical states of metals. The data from this study provides a rich dataset of metals in urban atmosphere and can be useful for targeted emission control to mitigate the adverse impact of metallic pollution on public health. Copyright © 2015 Elsevier B.V. All rights reserved.

Impacts of urbanization on surface sediment quality: evidence from polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs) contaminations in the Grand Canal of China.

PubMed

Hong, Youwei; Yu, Shen; Yu, Guangbin; Liu, Yi; Li, Guilin; Wang, Min

2012-06-01

Organic pollutants, especially synthetic organic compounds, can indicate paces of anthropogenic activities. Effects of urbanization on polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs) distributions in surface sediment were conducted in urban sections of the Grand Canal, China, consisting of a four-level urbanization gradient. The four-level urbanization gradients include three countryside towns, two small-size cities, three medium-size cities, and a large-size city. Diagnostic ratio analysis and factor analysis-multiple linear regression model were used for source apportionment of PAHs. Sediment quality guidelines (SQGs) of USA and Canada were employed to assess ecological risks of PAHs and PCBs in surface sediments of the Canal. Ranges of PAH and PCB concentrations in surface sediments were 0.66-22 mg/kg and 0.5-93 μg/kg, respectively. Coal-related sources were primary PAH sources and followed by vehicular emission. Total concentration, composition, and source apportionment of PAHs exhibited urbanization gradient effects. Total PCB concentrations increased with the urbanization gradient, while total PAHs concentration in surface sediments presented an inverted U Kuznets curve with the urbanization gradient. Elevated concentrations of both PAHs and PCBs ranged at effect range low levels or interim SQG, assessed by USA and Canadian SQGs. PAHs and PCBs in surface sediments of the Grand Canal showed urbanization gradient effects and low ecological risks.

Source apportionment of VOCs in the Los Angeles area using positive matrix factorization

NASA Astrophysics Data System (ADS)

Brown, Steven G.; Frankel, Anna; Hafner, Hilary R.

Eight 3-h speciated hydrocarbon measurements were collected daily by the South Coast Air Quality Management District (SCAQMD) as part of the Photochemical Assessment Monitoring Stations (PAMS) program during the summers of 2001-03 at two sites in the Los Angeles air basin, Azusa and Hawthorne. Over 30 hydrocarbons from over 500 samples at Azusa and 600 samples at Hawthorne were subsequently analyzed using the multivariate receptor model positive matrix factorization (PMF). At Azusa and Hawthorne, five and six factors were identified, respectively, with a good comparison between predicted and measured mass. At Azusa, evaporative emissions (a median of 31% of the total mass), motor vehicle exhaust (22%), liquid/unburned gasoline (27%), coatings (17%), and biogenic emissions (3%) factors were identified. Factors identified at Hawthorne were evaporative emissions (a median of 34% of the total mass), motor vehicle exhaust (24%), industrial process losses (15%), natural gas (13%), liquid/unburned gasoline (13%), and biogenic emissions (1%). Together, the median contribution from mobile source-related factors (exhaust, evaporative emissions, and liquid/unburned gasoline) was 80% and 71% at Azusa and Hawthorne, respectively, similar to previous source apportionment results using the chemical mass balance (CMB) model. There is a difference in the distribution among mobile source factors compared to the CMB work, with an increase in the contribution from evaporative emissions, though the cause (changes in emissions or differences between models) is unknown.

Source Apportionment of Particulate Matter Collected Upwind and Downwind of a Steel Facility in Granite City, IL (USA)

NASA Astrophysics Data System (ADS)

Duvall, R. M.; Norris, G. A.; Willis, R. D.; Turner, J. R.; Kaleel, R.; Sweitzer, T.; Preston, B.; Hays, M. D.

2009-04-01

St. Louis is currently in nonattainment of the annual PM2.5 National Ambient Air Quality Standard (NAAQS). Granite City Steel Works (GSCW), located in Granite City, IL is considered to be a significant source impacting the St. Louis area and the largest PM2.5 point source contributor. Twelve grab samples were collected in and around the steel facility including the basic oxygen furnace, steel and iron slag crushing, coal pulverizing, baghouse dust, paved road dust, and unpaved road dust. The bulk samples were resuspended in a resuspension chamber using a PM2.5 cutpoint and collected on Teflon, quartz and polycarbonate filters. Fine particulate matter (PM) samples (12-hr and 24-hr) were collected upwind and downwind of GSCW from October 13 to December 13, 2007 to identify sources contributing to nonattainment in St. Louis. The samples were analyzed for trace metals (X-Ray Fluorescence), ions (Ion Chromatography), elemental and organic carbon (thermal optical analysis), and organic species (solvent extraction Gas Chromatography/Mass Spectrometry). Source apportionment was conducted using the EPA Chemical Mass Balance (CMB) Model (v 8.2). Major sources impacting the 12-hr samples included the blast oxygen furnace, secondary sulfate, and road dust. Higher excess steel and coke works contributions were associated with higher wind speeds (greater than 5 mph) and more variability in source impacts was observed. Major sources impacting the 24-hr samples included secondary sulfate and motor vehicles (diesel and gasoline). Contributions were similar between the coke and steel works sources. Disclaimer: Although this work was reviewed by EPA and approved for publication, it may not necessarily reflect official Agency policy.

Evaluation of the absorption Ångström exponents for traffic and wood burning in the Aethalometer-based source apportionment using radiocarbon measurements of ambient aerosol

NASA Astrophysics Data System (ADS)

Zotter, Peter; Herich, Hanna; Gysel, Martin; El-Haddad, Imad; Zhang, Yanlin; Močnik, Griša; Hüglin, Christoph; Baltensperger, Urs; Szidat, Sönke; Prévôt, André S. H.

2017-03-01

Equivalent black carbon (EBC) measured by a multi-wavelength Aethalometer can be apportioned to traffic and wood burning. The method is based on the differences in the dependence of aerosol absorption on the wavelength of light used to investigate the sample, parameterized by the source-specific absorption Ångström exponent (α). While the spectral dependence (defined as α values) of the traffic-related EBC light absorption is low, wood smoke particles feature enhanced light absorption in the blue and near ultraviolet. Source apportionment results using this methodology are hence strongly dependent on the α values assumed for both types of emissions: traffic αTR, and wood burning αWB. Most studies use a single αTR and αWB pair in the Aethalometer model, derived from previous work. However, an accurate determination of the source specific α values is currently lacking and in some recent publications the applicability of the Aethalometer model was questioned.Here we present an indirect methodology for the determination of αWB and αTR by comparing the source apportionment of EBC using the Aethalometer model with 14C measurements of the EC fraction on 16 to 40 h filter samples from several locations and campaigns across Switzerland during 2005-2012, mainly in winter. The data obtained at eight stations with different source characteristics also enabled the evaluation of the performance and the uncertainties of the Aethalometer model in different environments. The best combination of αTR and αWB (0.9 and 1.68, respectively) was obtained by fitting the Aethalometer model outputs (calculated with the absorption coefficients at 470 and 950 nm) against the fossil fraction of EC (ECF / EC) derived from 14C measurements. Aethalometer and 14C source apportionment results are well correlated (r = 0.81) and the fitting residuals exhibit only a minor positive bias of 1.6 % and an average precision of 9.3 %. This indicates that the Aethalometer model reproduces reasonably well the 14C results for all stations investigated in this study using our best estimate of a single αWB and αTR pair. Combining the EC, 14C, and Aethalometer measurements further allowed assessing the dependence of the mass absorption cross section (MAC) of EBC on its source. Results indicate no significant difference in MAC at 880 nm between EBC originating from traffic or wood-burning emissions. Using ECF / EC as reference and constant a priori selected αTR values, αWB was also calculated for each individual data point. No clear station-to-station or season-to-season differences in αWB were observed, but αTR and αWB values are interdependent. For example, an increase in αTR by 0.1 results in a decrease in αWB by 0.1. The fitting residuals of different αTR and αWB combinations depend on ECF / EC such that a good agreement cannot be obtained over the entire ECF / EC range using other α pairs. Additional combinations of αTR = 0.8, and 1.0 and αWB = 1.8 and 1.6, respectively, are possible but only for ECF / EC between ˜ 40 and 85 %. Applying α values previously used in the literature such as αWB of ˜ 2 or any αWB in combination with αTR = 1.1 to our data set results in large residuals. Therefore we recommend to use the best α combination as obtained here (αTR = 0.9 and αWB = 1.68) in future studies when no or only limited additional information like 14C measurements are available. However, these results were obtained for locations impacted by black carbon (BC) mainly from traffic consisting of a modern car fleet and residential wood combustion with well-constrained combustion efficiencies. For regions of the world with different combustion conditions, additional BC sources, or fuels used, further investigations are needed.

23 CFR 192.7 - Apportionment of withheld funds after compliance.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 23 Highways 1 2014-04-01 2014-04-01 false Apportionment of withheld funds after compliance. 192.7 Section 192.7 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PAYMENT PROCEDURES DRUG OFFENDER'S DRIVER'S LICENSE SUSPENSION § 192.7 Apportionment of withheld funds after compliance...

23 CFR 192.7 - Apportionment of withheld funds after compliance.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 23 Highways 1 2013-04-01 2013-04-01 false Apportionment of withheld funds after compliance. 192.7 Section 192.7 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PAYMENT PROCEDURES DRUG OFFENDER'S DRIVER'S LICENSE SUSPENSION § 192.7 Apportionment of withheld funds after compliance...

23 CFR 192.7 - Apportionment of withheld funds after compliance.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 23 Highways 1 2010-04-01 2010-04-01 false Apportionment of withheld funds after compliance. 192.7 Section 192.7 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PAYMENT PROCEDURES DRUG OFFENDER'S DRIVER'S LICENSE SUSPENSION § 192.7 Apportionment of withheld funds after compliance...

23 CFR 192.7 - Apportionment of withheld funds after compliance.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 23 Highways 1 2011-04-01 2011-04-01 false Apportionment of withheld funds after compliance. 192.7 Section 192.7 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PAYMENT PROCEDURES DRUG OFFENDER'S DRIVER'S LICENSE SUSPENSION § 192.7 Apportionment of withheld funds after compliance...

Enrichment and geochemical mobility of heavy metals in bottom sediment of the Hoedong reservoir, Korea and their source apportionment.

PubMed

Lee, Pyeong-Koo; Kang, Min-Ju; Yu, Soonyoung; Ko, Kyung-Seok; Ha, Kyoochul; Shin, Seong-Cheon; Park, Jung Han

2017-10-01

Physicochemical characteristics of bottom sediment in the Hoedong reservoir were studied to evaluate the effectiveness of the reservoir as traps for trace metals. Roadside soil, stream sediment and background soil were also studied for comparison. Sequential extractions were carried out, and lead isotopic compositions of each extraction were determined to apportion Pb sources. Besides, particle size distribution of roadside soil, and metal concentrations and Pb isotopes of each size group were determined to characterize metal contamination. In result, Zn and Cu were enriched in sediment through roadside soil. The data on metal partitioning implied that Zn posed potential hazards for water quality. Meanwhile, the noticeable reduction of the 206 Pb/ 207 Pb isotopic ratio in the acid-soluble fraction in the size group 200 μm - 2 mm of national roadside soil indicated that this size group was highly contaminated by automotive emission with precipitation of acid-soluble secondary minerals during evaporation. Based on the Pb isotopic ratios, the dry deposition of Asian dust (AD) and non-Asian dust (NAD) affected roadside soil, while the effects of AD and NAD on bottom sediment appeared to be low given the low metal concentrations in sediment. Metal concentrations and Pb isotopic compositions indicated that sediments were a mixture of background and roadside soil. Source apportionment calculations showed that the average proportion of traffic Pb in bottom and stream sediments was respectively 34 and 31% in non-residual fractions, and 26 and 28% in residual fraction. The residual fraction of sediments appeared to be as contaminated as the non-residual fractions. Copyright © 2017 Elsevier Ltd. All rights reserved.

A Decade of Field Changing Atmospheric Aerosol Research ...

EPA Pesticide Factsheets

Conference: Gordon Research Conference in Atmospheric Chemistry, July 28 – August 2, 2013, VermontPresentation Type: PosterTitle: An Analysis of EPA’s STAR Program and a Decade of Field Changing Research in Atmospheric AerosolsAuthors: Kristina M. Wagstrom1,2, Sherri W. Hunt31Chemical and Biomolecular Engineering, University of Connecticut, Storrs, CT2AAAS Science and Technology Policy Fellow hosted by U.S. Environmental Protection Agency, National Center for Environmental Research3U.S. Environmental Protection Agency, National Center for Environmental ResearchA number of studies in the past decade have transformed the way we think about atmospheric aerosols. The advances include, but are not limited to, source apportionment of organics using aerosol mass spectrometer data, the volatility basis set approach, quantifying isoprene oxidation, and understanding the role of aqueous oxidation of organics on SOA formation. A series of grants funded by EPA just under ten years ago supported many of these advances. These projects make up the body of work awarded under two solicitations released by the EPA’s Science to Achieve Results (STAR) program: “Measurement, Modeling, and Analysis Methods for Airborne Carbonaceous Fine Particulate Matter” (2003) and “Source Apportionment of Particulate Matter” (2004). Our goal is to present the impact of the STAR solicitations and to show how they have pushed the field forward and led to new questions.In particular

Temporal patterns and source apportionment of nitrate-nitrogen leaching in a paddy field at Kelantan, Malaysia.

PubMed

Hussain, Hazilia; Yusoff, Mohd Kamil; Ramli, Mohd Firuz; Abd Latif, Puziah; Juahir, Hafizan; Zawawi, Mohamed Azwan Mohammed

2013-11-15

Nitrate-nitrogen leaching from agricultural areas is a major cause for groundwater pollution. Polluted groundwater with high levels of nitrate is hazardous and cause adverse health effects. Human consumption of water with elevated levels of NO3-N has been linked to the infant disorder methemoglobinemia and also to non-Hodgkin's disease lymphoma in adults. This research aims to study the temporal patterns and source apportionment of nitrate-nitrogen leaching in a paddy soil at Ladang Merdeka Ismail Mulong in Kelantan, Malaysia. The complex data matrix (128 x 16) of nitrate-nitrogen parameters was subjected to multivariate analysis mainly Principal Component Analysis (PCA) and Discriminant Analysis (DA). PCA extracted four principal components from this data set which explained 86.4% of the total variance. The most important contributors were soil physical properties confirmed using Alyuda Forecaster software (R2 = 0.98). Discriminant analysis was used to evaluate the temporal variation in soil nitrate-nitrogen on leaching process. Discriminant analysis gave four parameters (hydraulic head, evapotranspiration, rainfall and temperature) contributing more than 98% correct assignments in temporal analysis. DA allowed reduction in dimensionality of the large data set which defines the four operating parameters most efficient and economical to be monitored for temporal variations. This knowledge is important so as to protect the precious groundwater from contamination with nitrate.

Chemical characteristics and source apportionment of fine particulate organic carbon in Hong Kong during high particulate matter episodes in winter 2003

NASA Astrophysics Data System (ADS)

Li, Yun-Chun; Yu, Jian Zhen; Ho, Steven Sai Hang; Schauer, James J.; Yuan, Zibing; Lau, Alexis K. H.; Louie, Peter K. K.

2013-02-01

PM2.5 samples were collected at six general stations and one roadside station in Hong Kong in two periods of high particulate matter (PM) in 2003 (27 October-4 November and 30 November-13 December). The highest PM2.5 reached 216 μg m- 3 during the first high PM period and 113 μg m- 3 during the second high PM period. Analysis of synoptic weather conditions identified individual sampling days under dominant influence of one of three types of air masses, that is, local, regional and long-range transported (LRT) air masses. Roadside samples were discussed separately due to heavy influences from vehicular emissions. This research examines source apportionment of fine organic carbon (OC) and contribution of secondary organic aerosol on high PM days under different synoptic conditions. Six primary OC (POC) sources (vehicle exhaust, biomass burning, cooking, cigarette smoke, vegetative detritus, and coal combustion) were identified on the basis of characteristic organic tracers. Individual POC source contributions were estimated using chemical mass balance model. In the roadside and the local samples, OC was dominated by the primary sources, accounting for more than 74% of OC. In the samples influenced by regional and LRT air masses, secondary OC (SOC), which was approximated to be the difference between the total measured OC and the apportioned POC, contributed more than 54% of fine OC. SOC was highly correlated with water-soluble organic carbon and sulfate, consistent with its secondary nature.

Time resolved aerosol monitoring in the urban centre of Soweto

NASA Astrophysics Data System (ADS)

Formenti, P.; Annegarn, H. J.; Piketh, S. J.

1998-03-01

A programme of aerosol sampling was conducted from 1982 to 1984 in the urban area of Soweto, Johannesburg, South Africa. The particulate matter (aerodynamic diameter <15 μm) was collected using a two hours time resolution single stage streaker sampler and elemental concentrations were resolved via Particle Induced X-ray Emission (PIXE) analysis. Samples have been selected for analysis from an aerosol sample archive to establish base-line atmospheric conditions that existed in Soweto prior to large scale electrification, and to establish source apportionment of crustal elements between coal smoke and traffic induced road dust, based on chemical elemental measurements. A novel technique is demonstrated for processing PIXE-derived time sequence elemental concentration vectors. Slowly varying background components have been extracted from sulphur and crustal aerosol components, using alternatively two digital filters: a moving minimum, and a moving average. The residuals of the crustal elements, assigned to locally generated aerosol components, were modelled using surrogate tracers: sulphur as a surrogate for coal smoke; and Pb as a surrogate for traffic activity. Results from this source apportionment revealed coal emissions contributed between 40% and 50% of the aerosol mineral matter, while 18-22% originated from road dust. Background aerosol, characteristic of the regional winter aerosol burden over the South African Highveld, was between 12% and 21%. Minor contributors identified included a manganese smelter, located 30 km from the sampling site, and informal trash burning, as the source of intermittent heavy metals (Cu, Zn). Elemental source profiles derived for these various sources are presented.

Sediment source fingerprinting as an aid to catchment management: A review of the current state of knowledge and a methodological decision-tree for end-users

USGS Publications Warehouse

Collins, A.L; Pulley, S.; Foster, I.D.L; Gellis, Allen; Porto, P.; Horowitz, A.J.

2017-01-01

The growing awareness of the environmental significance of fine-grained sediment fluxes through catchment systems continues to underscore the need for reliable information on the principal sources of this material. Source estimates are difficult to obtain using traditional monitoring techniques, but sediment source fingerprinting or tracing procedures, have emerged as a potentially valuable alternative. Despite the rapidly increasing numbers of studies reporting the use of sediment source fingerprinting, several key challenges and uncertainties continue to hamper consensus among the international scientific community on key components of the existing methodological procedures. Accordingly, this contribution reviews and presents recent developments for several key aspects of fingerprinting, namely: sediment source classification, catchment source and target sediment sampling, tracer selection, grain size issues, tracer conservatism, source apportionment modelling, and assessment of source predictions using artificial mixtures. Finally, a decision-tree representing the current state of knowledge is presented, to guide end-users in applying the fingerprinting approach.

Response of dissolved trace metals to land use/land cover and their source apportionment using a receptor model in a subtropic river, China.

PubMed

Li, Siyue; Zhang, Quanfa

2011-06-15

Water samples were collected for determination of dissolved trace metals in 56 sampling sites throughout the upper Han River, China. Multivariate statistical analyses including correlation analysis, stepwise multiple linear regression models, and principal component and factor analysis (PCA/FA) were employed to examine the land use influences on trace metals, and a receptor model of factor analysis-multiple linear regression (FA-MLR) was used for source identification/apportionment of anthropogenic heavy metals in the surface water of the River. Our results revealed that land use was an important factor in water metals in the snow melt flow period and land use in the riparian zone was not a better predictor of metals than land use away from the river. Urbanization in a watershed and vegetation along river networks could better explain metals, and agriculture, regardless of its relative location, however slightly explained metal variables in the upper Han River. FA-MLR analysis identified five source types of metals, and mining, fossil fuel combustion, and vehicle exhaust were the dominant pollutions in the surface waters. The results demonstrated great impacts of human activities on metal concentrations in the subtropical river of China. Copyright © 2011 Elsevier B.V. All rights reserved.

Atmospheric aerosol composition and source apportionments to aerosol in southern Taiwan

NASA Astrophysics Data System (ADS)

Tsai, Ying I.; Chen, Chien-Lung

In this study, the chemical characteristics of winter aerosol at four sites in southern Taiwan were determined and the Gaussian Trajectory transfer coefficient model (GTx) was then used to identify the major air pollutant sources affecting the study sites. Aerosols were found to be acidic at all four sites. The most important constituents of the particulate matter (PM) by mass were SO 42-, organic carbon (OC), NO 3-, elemental carbon (EC) and NH 4+, with SO 42-, NO 3-, and NH 4+ together constituting 86.0-87.9% of the total PM 2.5 soluble inorganic salts and 68.9-78.3% of the total PM 2.5-10 soluble inorganic salts, showing that secondary photochemical solution components such as these were the major contributors to the aerosol water-soluble ions. The coastal site, Linyuan (LY), had the highest PM mass percentage of sea salts, higher in the coarse fraction, and higher sea salts during daytime than during nighttime, indicating that the prevailing daytime sea breeze brought with it more sea-salt aerosol. Other than sea salts, crustal matter, and EC in PM 2.5 at Jenwu (JW) and in PM 2.5-10 at LY, all aerosol components were higher during nighttime, due to relatively low nighttime mixing heights limiting vertical and horizontal dispersion. At JW, a site with heavy traffic loadings, the OC/EC ratio in the nighttime fine and coarse fractions of approximately 2.2 was higher than during daytime, indicating that in addition to primary organic aerosol (POA), secondary organic aerosol (SOA) also contributed to the nighttime PM 2.5. This was also true of the nighttime coarse fraction at LY. The GTx produced correlation coefficients ( r) for simulated and observed daily concentrations of PM 10 at the four sites (receptors) in the range 0.45-0.59 and biases from -6% to -20%. Source apportionment indicated that point sources were the largest PM 10 source at JW, LY and Daliao (DL), while at Meinung (MN), a suburban site with less local PM 10, SO x and NO x emissions, upwind boundary concentration was the major PM 10 source, followed by point sources and top boundary concentration.

77 FR 42359 - FTA Supplemental Fiscal Year 2012 Apportionments, Allocations, and Program Information

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-18

... FEDERAL TRANSIT ADMINISTRATION FTA Supplemental Fiscal Year 2012 Apportionments, Allocations, and... partial apportionment notices. This notice announces the full fiscal year (FY) 2012 contract authority... Transportation Extension Act of 2012, Part II, Found in Division G of Moving Ahead for Progress in the 21st...

14 CFR 1214.105 - Apportionment and/or assignment of services.

Code of Federal Regulations, 2011 CFR

2011-01-01

... FLIGHT General Provisions Regarding Space Shuttle Flights of Payloads for Non-U.S. Government, Reimbursable Customers § 1214.105 Apportionment and/or assignment of services. (a) Subject to NASA approval, a customer may apportion and/or assign Shuttle services to third parties within the payload. No apportionment...

14 CFR 1214.105 - Apportionment and/or assignment of services.

Code of Federal Regulations, 2012 CFR

2012-01-01

... FLIGHT General Provisions Regarding Space Shuttle Flights of Payloads for Non-U.S. Government, Reimbursable Customers § 1214.105 Apportionment and/or assignment of services. (a) Subject to NASA approval, a customer may apportion and/or assign Shuttle services to third parties within the payload. No apportionment...

14 CFR 1214.105 - Apportionment and/or assignment of services.

Code of Federal Regulations, 2013 CFR

2013-01-01

... FLIGHT General Provisions Regarding Space Shuttle Flights of Payloads for Non-U.S. Government, Reimbursable Customers § 1214.105 Apportionment and/or assignment of services. (a) Subject to NASA approval, a customer may apportion and/or assign Shuttle services to third parties within the payload. No apportionment...

77 FR 19154 - Allocation and Apportionment of Interest Expense; Hearing Cancellation

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-30

... Allocation and Apportionment of Interest Expense; Hearing Cancellation AGENCY: Internal Revenue Service (IRS... apportionment of interest expense. DATES: The public hearing, originally scheduled for April 3, 2012 at 10 a.m... cross-reference to temporary regulations and a notice of public hearing instructed those interested in...

Seasonal variability and source apportionment of volatile organic compounds (VOCs) in the Paris megacity (France)

NASA Astrophysics Data System (ADS)

Baudic, Alexia; Gros, Valérie; Sauvage, Stéphane; Locoge, Nadine; Sanchez, Olivier; Sarda-Estève, Roland; Kalogridis, Cerise; Petit, Jean-Eudes; Bonnaire, Nicolas; Baisnée, Dominique; Favez, Olivier; Albinet, Alexandre; Sciare, Jean; Bonsang, Bernard

2016-09-01

Within the framework of air quality studies at the megacity scale, highly time-resolved volatile organic compound (C2-C8) measurements were performed in downtown Paris (urban background sites) from January to November 2010. This unique dataset included non-methane hydrocarbons (NMHCs) and aromatic/oxygenated species (OVOCs) measured by a GC-FID (gas chromatograph with a flame ionization detector) and a PTR-MS (proton transfer reaction - mass spectrometer), respectively. This study presents the seasonal variability of atmospheric VOCs being monitored in the French megacity and their various associated emission sources. Clear seasonal and diurnal patterns differed from one VOC to another as the result of their different origins and the influence of environmental parameters (solar radiation, temperature). Source apportionment (SA) was comprehensively conducted using a multivariate mathematical receptor modeling. The United States Environmental Protection Agency's positive matrix factorization tool (US EPA, PMF) was used to apportion and quantify ambient VOC concentrations into six different sources. The modeled source profiles were identified from near-field observations (measurements from three distinct emission sources: inside a highway tunnel, at a fireplace and from a domestic gas flue, hence with a specific focus on road traffic, wood-burning activities and natural gas emissions) and hydrocarbon profiles reported in the literature. The reconstructed VOC sources were cross validated using independent tracers such as inorganic gases (NO, NO2, CO), black carbon (BC) and meteorological data (temperature). The largest contributors to the predicted VOC concentrations were traffic-related activities (including motor vehicle exhaust, 15 % of the total mass on the annual average, and evaporative sources, 10 %), with the remaining emissions from natural gas and background (23 %), solvent use (20 %), wood-burning (18 %) and a biogenic source (15 %). An important finding of this work is the significant contribution from wood-burning, especially in winter, where it could represent up to ˜ 50 % of the total mass of VOCs. Biogenic emissions also surprisingly contributed up to ˜ 30 % in summer (due to the dominating weight of OVOCs in this source). Finally, the mixed natural gas and background source exhibited a high contribution in spring (35 %, when continental air influences were observed) and in autumn (23 %, for home heating consumption).

Assessment and application of clustering techniques to atmospheric particle number size distribution for the purpose of source apportionment

NASA Astrophysics Data System (ADS)

Salimi, F.; Ristovski, Z.; Mazaheri, M.; Laiman, R.; Crilley, L. R.; He, C.; Clifford, S.; Morawska, L.

2014-06-01

Long-term measurements of particle number size distribution (PNSD) produce a very large number of observations and their analysis requires an efficient approach in order to produce results in the least possible time and with maximum accuracy. Clustering techniques are a family of sophisticated methods which have been recently employed to analyse PNSD data, however, very little information is available comparing the performance of different clustering techniques on PNSD data. This study aims to apply several clustering techniques (i.e. K-means, PAM, CLARA and SOM) to PNSD data, in order to identify and apply the optimum technique to PNSD data measured at 25 sites across Brisbane, Australia. A new method, based on the Generalised Additive Model (GAM) with a basis of penalised B-splines, was proposed to parameterise the PNSD data and the temporal weight of each cluster was also estimated using the GAM. In addition, each cluster was associated with its possible source based on the results of this parameterisation, together with the characteristics of each cluster. The performances of four clustering techniques were compared using the Dunn index and silhouette width validation values and the K-means technique was found to have the highest performance, with five clusters being the optimum. Therefore, five clusters were found within the data using the K-means technique. The diurnal occurrence of each cluster was used together with other air quality parameters, temporal trends and the physical properties of each cluster, in order to attribute each cluster to its source and origin. The five clusters were attributed to three major sources and origins, including regional background particles, photochemically induced nucleated particles and vehicle generated particles. Overall, clustering was found to be an effective technique for attributing each particle size spectra to its source and the GAM was suitable to parameterise the PNSD data. These two techniques can help researchers immensely in analysing PNSD data for characterisation and source apportionment purposes.

Assessment and application of clustering techniques to atmospheric particle number size distribution for the purpose of source apportionment

NASA Astrophysics Data System (ADS)

Salimi, F.; Ristovski, Z.; Mazaheri, M.; Laiman, R.; Crilley, L. R.; He, C.; Clifford, S.; Morawska, L.

2014-11-01

Long-term measurements of particle number size distribution (PNSD) produce a very large number of observations and their analysis requires an efficient approach in order to produce results in the least possible time and with maximum accuracy. Clustering techniques are a family of sophisticated methods that have been recently employed to analyse PNSD data; however, very little information is available comparing the performance of different clustering techniques on PNSD data. This study aims to apply several clustering techniques (i.e. K means, PAM, CLARA and SOM) to PNSD data, in order to identify and apply the optimum technique to PNSD data measured at 25 sites across Brisbane, Australia. A new method, based on the Generalised Additive Model (GAM) with a basis of penalised B-splines, was proposed to parameterise the PNSD data and the temporal weight of each cluster was also estimated using the GAM. In addition, each cluster was associated with its possible source based on the results of this parameterisation, together with the characteristics of each cluster. The performances of four clustering techniques were compared using the Dunn index and Silhouette width validation values and the K means technique was found to have the highest performance, with five clusters being the optimum. Therefore, five clusters were found within the data using the K means technique. The diurnal occurrence of each cluster was used together with other air quality parameters, temporal trends and the physical properties of each cluster, in order to attribute each cluster to its source and origin. The five clusters were attributed to three major sources and origins, including regional background particles, photochemically induced nucleated particles and vehicle generated particles. Overall, clustering was found to be an effective technique for attributing each particle size spectrum to its source and the GAM was suitable to parameterise the PNSD data. These two techniques can help researchers immensely in analysing PNSD data for characterisation and source apportionment purposes.

Characterization of PM2.5 in Guangzhou, China: uses of organic markers for supporting source apportionment.

PubMed

Wang, Jingzhi; Ho, Steven Sai Hang; Ma, Shexia; Cao, Junji; Dai, Wenting; Liu, Suixin; Shen, Zhenxing; Huang, Rujin; Wang, Gehui; Han, Yongming

2016-04-15

Organic carbon (OC), elemental carbon (EC), and non-polar organic compounds including n-alkanes (n-C14-n-C40), polycyclic aromatic hydrocarbons (PAHs), phthalate esters (PAEs) and hopanes were quantified in fine particulate (PM2.5), which were collected in urban area of Guangzhou, China in winter and summer in 2012/2013. The pollutants levels were well comparable with the data obtained in previous studies in Pearl River Delta (PRD) region but much lower than most northern Chinese megacities. The contribution of EC to PM2.5 and OC/EC ratio suggest that the pollution sources were relatively consistent in GZ between the two seasons. Benzo[a]pyrene (BaP) was the most abundant PAHs, which were 4.9 and 1.0ng/m(3) on average, accounting for 10.7% and 9.1% to the total quantified PAHs in winter and summer, respectively. The total concentrations of PAEs ranged from 289.1 to 2435ng/m(3) and from 102.4 to 1437ng/m(3), respectively, in winter and summer. Di-n-butyl phthalate (DBP) was the most dominant PAEs. The ambient levels of PAEs could be partly attributed to the widespread uses of the household products, municipal garbage compressing, sewage, and external painting material on the building. Source apportionment for OC with chemical mass balance (CMB) model demonstrated coal combustion, vehicle emission, cooking, and secondary organic compounds (SOC) formation were the four major pollution sources. Both of the indices of n-alkanes and diagnostic PAHs ratios support that anthropogenic sources such as vehicle emission and coal combustion were the significant pollution sources with some extents from epicuticular waxes by terrestrial plants. The ratio of hopanes to EC proved the influences from vehicle emission, and displayed a certain degree of the air aging in the Guangzhou ambient air. Copyright © 2016 Elsevier B.V. All rights reserved.

Differences Between Magnitudes and Health Impacts of BC Emissions Across the United States Using 12 km Scale Seasonal Source Apportionment

EPA Science Inventory

Recent assessments have analyzed the health impacts of PM2.5 from emissions from different locations and sectors using simplified or reduced-form air quality models. Here we present an alternative approach using the adjoint of the Community Multiscale Air Quality (CMAQ) model, wh...

Source Apportionment of Ambient Fine Particulate Matter in Dearborn, Michigan, using Hourly Resolved PM Chemical Composition Data

EPA Science Inventory

High time-resolution aerosol sampling was conducted for one month during July–August 2007 in Dearborn, MI, a non-attainment area for fine particulate matter (PM2.5) National Ambient Air Quality Standards (NAAQS). Measurements of more than 30 PM2.5 species were made using a suite o...

77 FR 30248 - Approval and Promulgation of Implementation Plans; State of Idaho; Regional Haze State...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-22

... range (or deciview), which is the greatest distance, in kilometers or miles, at which a dark object can... Comprehensive Air Quality Model with Extensions (CAMx) and Particulate Matter Source Apportionment Technology... air for NO X , wet flue gas desulfurization for SO 2 and the existing baghouse for particulate matter...

Two Model-Based Methods for Policy Analyses of Fine Particulate Matter Control in China: Source Apportionment and Source Sensitivity

NASA Astrophysics Data System (ADS)

Li, X.; Zhang, Y.; Zheng, B.; Zhang, Q.; He, K.

2013-12-01

Anthropogenic emissions have been controlled in recent years in China to mitigate fine particulate matter (PM2.5) pollution. Recent studies show that sulfate dioxide (SO2)-only control cannot reduce total PM2.5 levels efficiently. Other species such as nitrogen oxide, ammonia, black carbon, and organic carbon may be equally important during particular seasons. Furthermore, each species is emitted from several anthropogenic sectors (e.g., industry, power plant, transportation, residential and agriculture). On the other hand, contribution of one emission sector to PM2.5 represents contributions of all species in this sector. In this work, two model-based methods are used to identify the most influential emission sectors and areas to PM2.5. The first method is the source apportionment (SA) based on the Particulate Source Apportionment Technology (PSAT) available in the Comprehensive Air Quality Model with extensions (CAMx) driven by meteorological predictions of the Weather Research and Forecast (WRF) model. The second method is the source sensitivity (SS) based on an adjoint integration technique (AIT) available in the GEOS-Chem model. The SA method attributes simulated PM2.5 concentrations to each emission group, while the SS method calculates their sensitivity to each emission group, accounting for the non-linear relationship between PM2.5 and its precursors. Despite their differences, the complementary nature of the two methods enables a complete analysis of source-receptor relationships to support emission control policies. Our objectives are to quantify the contributions of each emission group/area to PM2.5 in the receptor areas and to intercompare results from the two methods to gain a comprehensive understanding of the role of emission sources in PM2.5 formation. The results will be compared in terms of the magnitudes and rankings of SS or SA of emitted species and emission groups/areas. GEOS-Chem with AIT is applied over East Asia at a horizontal grid resolution of 0.5° (Lat) × 0.67° (Lon). WRF/CAMx with PSAT is applied to nested grids: 36-km × 36-km over China and 12-km × 12-km over northern China. These simulations are performed for 2006 and 2011. Beijing and northern Hebei are selected as representative receptor areas. Simulated surface concentrations by both models are evaluated with available observations in China. Focusing on inorganic aerosols (sulfate, nitrate and ammonium), preliminary SS results from GEOS-Chem/AIT at Beijing identify the top three major emission sectors to be agriculture, residential, and transportation in winter and agriculture, industry and power plant in summer. The top four source areas are northern Hebei, local, Neimenggu, and Liaoning in winter and northern Hebei, local, Shandong, and southern Hebei in summer. The synthesis of SS and SA for influential emission groups or areas from this work will provide a quantitative basis for emission control strategy development and policy making for PM2.5 control in China.

A modification of the Regional Nutrient Management model (ReNuMa) to identify long-term changes in riverine nitrogen sources

NASA Astrophysics Data System (ADS)

Hu, Minpeng; Liu, Yanmei; Wang, Jiahui; Dahlgren, Randy A.; Chen, Dingjiang

2018-06-01

Source apportionment is critical for guiding development of efficient watershed nitrogen (N) pollution control measures. The ReNuMa (Regional Nutrient Management) model, a semi-empirical, semi-process-oriented model with modest data requirements, has been widely used for riverine N source apportionment. However, the ReNuMa model contains limitations for addressing long-term N dynamics by ignoring temporal changes in atmospheric N deposition rates and N-leaching lag effects. This work modified the ReNuMa model by revising the source code to allow yearly changes in atmospheric N deposition and incorporation of N-leaching lag effects into N transport processes. The appropriate N-leaching lag time was determined from cross-correlation analysis between annual watershed individual N source inputs and riverine N export. Accuracy of the modified ReNuMa model was demonstrated through analysis of a 31-year water quality record (1980-2010) from the Yongan watershed in eastern China. The revisions considerably improved the accuracy (Nash-Sutcliff coefficient increased by ∼0.2) of the modified ReNuMa model for predicting riverine N loads. The modified model explicitly identified annual and seasonal changes in contributions of various N sources (i.e., point vs. nonpoint source, surface runoff vs. groundwater) to riverine N loads as well as the fate of watershed anthropogenic N inputs. Model results were consistent with previously modeled or observed lag time length as well as changes in riverine chloride and nitrate concentrations during the low-flow regime and available N levels in agricultural soils of this watershed. The modified ReNuMa model is applicable for addressing long-term changes in riverine N sources, providing decision-makers with critical information for guiding watershed N pollution control strategies.

Sources of nitrogen and phosphorus emissions to Irish rivers and coastal waters: Estimates from a nutrient load apportionment framework.

PubMed

Mockler, Eva M; Deakin, Jenny; Archbold, Marie; Gill, Laurence; Daly, Donal; Bruen, Michael

2017-12-01

More than half of surface water bodies in Europe are at less than good ecological status according to Water Framework Directive assessments, and diffuse pollution from agriculture remains a major, but not the only, cause of this poor performance. Agri-environmental policy and land management practices have, in many areas, reduced nutrient emissions to water. However, additional measures may be required in Ireland to further decouple the relationship between agricultural productivity and emissions to water, which is of vital importance given on-going agricultural intensification. The Source Load Apportionment Model (SLAM) framework characterises sources of phosphorus (P) and nitrogen (N) emissions to water at a range of scales from sub-catchment to national. The SLAM synthesises land use and physical characteristics to predict emissions from point (wastewater, industry discharges and septic tank systems) and diffuse sources (agriculture, forestry, etc.). The predicted annual nutrient emissions were assessed against monitoring data for 16 major river catchments covering 50% of the area of Ireland. At national scale, results indicate that total average annual emissions to surface water in Ireland are over 2700tyr -1 of P and 82,000tyr -1 of N. The proportional contributions from individual sources show that the main sources of P are from municipal wastewater treatment plants and agriculture, with wide variations across the country related to local anthropogenic pressures and the hydrogeological setting. Agriculture is the main source of N emissions to water across all regions of Ireland. These policy-relevant results synthesised large amounts of information in order to identify the dominant sources of nutrients at regional and local scales, contributing to the national nutrient risk assessment of Irish water bodies. Copyright © 2017 The Authors. Published by Elsevier B.V. All rights reserved.

7 CFR Appendix to Part 227 - Apportionment of Funds for Nutrition Education and Training

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 4 2011-01-01 2011-01-01 false Apportionment of Funds for Nutrition Education and... NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE CHILD NUTRITION PROGRAMS NUTRITION EDUCATION AND TRAINING PROGRAM Pt. 227, App. Appendix to Part 227—Apportionment of Funds for Nutrition Education and Training...

7 CFR Appendix to Part 227 - Apportionment of Funds for Nutrition Education and Training

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 4 2013-01-01 2013-01-01 false Apportionment of Funds for Nutrition Education and... NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE CHILD NUTRITION PROGRAMS NUTRITION EDUCATION AND TRAINING PROGRAM Pt. 227, App. Appendix to Part 227—Apportionment of Funds for Nutrition Education and Training...

7 CFR Appendix to Part 227 - Apportionment of Funds for Nutrition Education and Training

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 4 2010-01-01 2010-01-01 false Apportionment of Funds for Nutrition Education and... NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE CHILD NUTRITION PROGRAMS NUTRITION EDUCATION AND TRAINING PROGRAM Pt. 227, App. Appendix to Part 227—Apportionment of Funds for Nutrition Education and Training...

7 CFR Appendix to Part 227 - Apportionment of Funds for Nutrition Education and Training

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 4 2012-01-01 2012-01-01 false Apportionment of Funds for Nutrition Education and... NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE CHILD NUTRITION PROGRAMS NUTRITION EDUCATION AND TRAINING PROGRAM Pt. 227, App. Appendix to Part 227—Apportionment of Funds for Nutrition Education and Training...

7 CFR Appendix to Part 227 - Apportionment of Funds for Nutrition Education and Training

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 4 2014-01-01 2014-01-01 false Apportionment of Funds for Nutrition Education and... NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE CHILD NUTRITION PROGRAMS NUTRITION EDUCATION AND TRAINING PROGRAM Pt. 227, App. Appendix to Part 227—Apportionment of Funds for Nutrition Education and Training...

14 CFR § 1214.105 - Apportionment and/or assignment of services.

Code of Federal Regulations, 2014 CFR

2014-01-01

... SPACE FLIGHT General Provisions Regarding Space Shuttle Flights of Payloads for Non-U.S. Government, Reimbursable Customers § 1214.105 Apportionment and/or assignment of services. (a) Subject to NASA approval, a customer may apportion and/or assign Shuttle services to third parties within the payload. No apportionment...

Computational Medical Apportionment Determination for Impairment Ratings

NASA Astrophysics Data System (ADS)

Artz, Jerry; Thompson, Marten; Alchemy, Md, John; Penn, Md, Daniel

2017-01-01

Unique computational techniques are used to calculate apportionment percentages for Whole Person Impairment (WPI) Ratings for workers with job-related injuries/illnesses. This interdisciplinary project includes collaboration among physicists, engineers, and concerned medical professionals. Medical providers are often asked to medically determine multiple contributing factors to disease states (e.g. diabetes, obesity, arthritis, and prior injury) in the context of personal injury as it pertains to permanent impairment. The process of making this determination is referred to as ``apportionment''. The economic value of apportionment is far reaching and represents a significant impact to all stakeholders in the injury resolution and settlement arena. The process of apportionment is necessary to assign monetary value for the stakeholders when an injury occurs. The ultimate trier-of-fact is the judicial system. The medical provider's role in this capacity is to apply known medical scientific knowledge and present it in a format that is objective and reproducible for the stakeholders. In this presentation the traditional challenges of apportionment will be outlined, and a novel approach creating mathematical bounding and modeling of pathology-weighted data sets will be presented.

On the possibility of real time air quality and toxicology assessment using multi-wavelength photoacoustic spectroscopy

NASA Astrophysics Data System (ADS)

Ajtai, Tibor; Pinter, Mate; Utry, Noemi; Kiss-Albert, Gergely; Palagyi, Andrea; Manczinger, Laszlo; Vagvölgyi, Csaba; Szabo, Gabor; Bozoki, Zoltan

2016-04-01

In this study we present results of field measurement campaigns focusing on the in-situ characterization of absorption spectra and the health relevance of light absorbing carbonaceous (LAC) in the ambient. The absorption spectra is measured @ 266, 355, 532 and 1064 nm by our state-of-the-art four-wavelength photoacoustic instrument, while for health relevance the eco- cito and genotoxicity parameters were measured using standardized methodologies. We experimentally demonstrated a correlation between the toxicities and the measured absorption spectra quantified by its wavelength dependency. Based on this correlation, we present novel possibilities on real-time air quality monitoring. LAC is extensively studied not only because of its considerable climate effects but as a serious air pollutant too. Gradually increasing number of studies demonstrated experimentally that the health effect of LAC is more serious than it is expected based on its share in total atmospheric aerosol mass. Furthermore during many local pollution events LAC not only has dominancy but it is close to exclusivity. Altogether due to its climate and health effects many studies and proposed regulations focus on the physical, chemical and toxicological properties of LAC as well as on its source apportionment. Despites of its importance, there is not yet a widely accepted standard methodology for the real-time and selective identification of LAC. There are many different reasons of that: starting from its complex inherent physicochemical features including many unknown constituents, via masking effect of ambient on the inherent physicochemical properties taking place even in case of a short residence, ending with the lack of reliable instrumentation for its health or source relevant parameters. Therefore, the methodology and instrument development for selective and reliable identification of LAC is timely and important issues in climate and air quality researches. Recently, many studies demonstrated correlation between the chemical compositions and the absorption features of LAC which open up novel possibilities in real time source apportionment and in air quality monitoring.

Source insights into the 11-h daytime and nighttime fine ambient particulate matter in China as well as the synthetic studies using the new Multilinear Engine 2-species ratios (ME2-SR) method.

PubMed

Shi, Guoliang; Chen, Gang; Liu, Guirong; Wang, Haiting; Tian, Yingze; Feng, Yinchang

2016-10-01

Modeled results are very important for environmental management. Unreasonable modeled result can lead to wrong strategy for air pollution management. In this work, an improved physically constrained source apportionment (PCSA) technology known as Multilinear Engine 2-species ratios (ME2-SR) was developed to the 11-h daytime and nighttime fine ambient particulate matter in urban area. Firstly, synthetic studies were carried out to explore the effectiveness of ME2-SR. The estimated source contributions were compared with the true values. The results suggest that, compared with the positive matrix factorization (PMF) model, the ME2-SR method could obtain more physically reliable outcomes, indicating that ME2-SR was effective, especially when apportioning the datasets with no unknown source. Additionally, 11-h daytime and nighttime PM2.5 samples were collected from Tianjin in China. The sources of the 11-h daytime and nighttime fine ambient particulate matter in China were identified using the new method and the PMF model. The calculated source contributions for ME2-SR for daytime PM2.5 samples are resuspended dust (38.91 μg m(-3), 26.60%), sulfate and nitrate (38.60 μg m(-3), 26.39%), vehicle exhaust and road dust (38.26 μg m(-3), 26.16%) and coal combustion (20.14 μg m(-3), 13.77%), and those for nighttime PM2.5 samples are resuspended dust (18.78 μg m(-3), 12.91%), sulfate and nitrate (41.57 μg m(-3), 28.58%), vehicle exhaust and road dust (38.39 μg m(-3), 26.39%), and coal combustion (36.76 μg m(-3), 25.27%). The comparisons of the constrained versus unconstrained outcomes clearly suggest that the physical meaning of the ME2-SR results is interpretable and reliable, not only for the specified species values but also for source contributions. The findings indicate that the ME2-SR method can be a useful tool in source apportionment studies, for air pollution management. Copyright © 2016 Elsevier Ltd. All rights reserved.

Development and Application of Novel Sampling Methodologies for Study of Volatile Particulate Matter in Military Aircraft Emissions

DTIC Science & Technology

2012-09-01

experiments. J. Aerosol Sci., 40, 603- 612. Zheng, M., Cass, G. R., Schauer, J. J., Edgerton, E. S. (2002) Source Apportionment of PM2.5 in the...Energy Heavy Vehicle Research Program. The SERDP project WP1627 team consists of the following members (listed in alphabetical order of the last name...aircraft emissions are dominated by a fleet of high payload aircraft, such as the C-130, B1 B-52, and a variety of heavy -lift turboshaft vehicles

Impact of emissions from natural gas production facilities on ambient air quality in the Barnett Shale area: a pilot study.

PubMed

Zielinska, Barbara; Campbell, Dave; Samburova, Vera

2014-12-01

Rapid and extensive development of shale gas resources in the Barnett Shale region of Texas in recent years has created concerns about potential environmental impacts on water and air quality. The purpose of this study was to provide a better understanding of the potential contributions of emissions from gas production operations to population exposure to air toxics in the Barnett Shale region. This goal was approached using a combination of chemical characterization of the volatile organic compound (VOC) emissions from active wells, saturation monitoring for gaseous and particulate pollutants in a residential community located near active gas/oil extraction and processing facilities, source apportionment of VOCs measured in the community using the Chemical Mass Balance (CMB) receptor model, and direct measurements of the pollutant gradient downwind of a gas well with high VOC emissions. Overall, the study results indicate that air quality impacts due to individual gas wells and compressor stations are not likely to be discernible beyond a distance of approximately 100 m in the downwind direction. However, source apportionment results indicate a significant contribution to regional VOCs from gas production sources, particularly for lower-molecular-weight alkanes (< C6). Although measured ambient VOC concentrations were well below health-based safe exposure levels, the existence of urban-level mean concentrations of benzene and other mobile source air toxics combined with soot to total carbon ratios that were high for an area with little residential or commercial development may be indicative of the impact of increased heavy-duty vehicle traffic related to gas production. Implications: Rapid and extensive development of shale gas resources in recent years has created concerns about potential environmental impacts on water and air quality. This study focused on directly measuring the ambient air pollutant levels occurring at residential properties located near natural gas extraction and processing facilities, and estimating the relative contributions from gas production and motor vehicle emissions to ambient VOC concentrations. Although only a small-scale case study, the results may be useful for guidance in planning future ambient air quality studies and human exposure estimates in areas of intensive shale gas production.

7 CFR 1412.49 - Apportionment of long and medium grain rice.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 10 2012-01-01 2012-01-01 false Apportionment of long and medium grain rice. 1412.49... and Peanuts 2008 through 2012 § 1412.49 Apportionment of long and medium grain rice. (a) Rice base...) Medium grain rice. Medium grain rice includes short grain rice. (c) Owners on a farm will elect rice base...

7 CFR 1412.49 - Apportionment of long and medium grain rice.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false Apportionment of long and medium grain rice. 1412.49... and Peanuts 2008 through 2012 § 1412.49 Apportionment of long and medium grain rice. (a) Rice base...) Medium grain rice. Medium grain rice includes short grain rice. (c) Owners on a farm will elect rice base...

7 CFR 1412.49 - Apportionment of long and medium grain rice.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 10 2013-01-01 2013-01-01 false Apportionment of long and medium grain rice. 1412.49... and Peanuts 2008 Through 2012 § 1412.49 Apportionment of long and medium grain rice. (a) Rice base...) Medium grain rice. Medium grain rice includes short grain rice. (c) Owners on a farm will elect rice base...

7 CFR 1412.49 - Apportionment of long and medium grain rice.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 10 2011-01-01 2011-01-01 false Apportionment of long and medium grain rice. 1412.49... and Peanuts 2008 through 2012 § 1412.49 Apportionment of long and medium grain rice. (a) Rice base...) Medium grain rice. Medium grain rice includes short grain rice. (c) Owners on a farm will elect rice base...

7 CFR 1412.49 - Apportionment of long and medium grain rice.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 10 2014-01-01 2014-01-01 false Apportionment of long and medium grain rice. 1412.49... and Peanuts 2008 Through 2012 § 1412.49 Apportionment of long and medium grain rice. (a) Rice base...) Medium grain rice. Medium grain rice includes short grain rice. (c) Owners on a farm will elect rice base...

Source apportionment of atmospheric polycyclic aromatic hydrocarbons (PAHs) in Palm Beach County, Florida.

PubMed

Afshar-Mohajer, Nima; Wilson, Christina; Wu, Chang-Yu; Stormer, James E

2016-04-01

Due to concerns about adverse health effects associated with inhalation of atmospheric polycyclic aromatic hydrocarbons (PAHs), 30 ambient air samples were obtained at an air quality monitoring station in Palm Beach County, Florida, from March 2013 to March 2014. The ambient PAH concentration measurements and fractional emission rates of known sources were incorporated into a chemical mass balance model, CMB8.2, developed by EPA, to apportion contributions of three major PAH sources including preharvest sugarcane burning, mobile vehicles, and wildland fires. Strong association between the number of benzene rings and source contribution was found, and mobile vehicles were identified to be the prevailing source (contribution≥56%) for the observed PAHs concentration with lower molecular weights (four or fewer benzene rings) throughout the year. Preharvest sugarcane burning was the primary contributing source for PAHs with relatively higher molecular weights (five or more benzene rings) during the sugarcane burning season (from October to May of the next year). Source contribution of wildland fires varied among PAH compounds but was consistently lower than for sugarcane burning during the sugarcane harvest season. Determining the major sources responsible for ground-level PAHs serves as a tool to improving management strategies for PAH emitting sources and a step toward better protection of the health of residents in terms of exposure to PAHs. The results obtain insight into temporal dominance of PAH polluting sources for those residential areas located near sugarcane burning facilities and have implications beyond Palm Beach County, in areas with high concerns of PAHs and their linked sources. Source apportionment of atmospheric polycyclic hydrocarbons (PAHs) in Palm Beach County, Florida, meant to estimate contributions of major sources in PAH concentrations measured at Belle Glade City of Palm Beach County. Number of benzene rings was found to be the key parameter in determining the source with the prevailing contribution. Mobile vehicle sources showed a higher contribution for species with four or fewer benzene rings, whereas sugarcane burning contributed more for species with five or more benzene rings. Results from this study encourage more control for sugarcane burns and help to better manage authorization of the sugarcane burning incidents and more restrictive transportation plans to limit PAH emissions from mobile vehicles.

Background PM2.5 source apportionment in the remote Northwestern United States

NASA Astrophysics Data System (ADS)

Hadley, Odelle L.

2017-10-01

This study used the Environmental Protection Agency's positive matrix factorization model (EPA PMF5.0) to identify five primary source factors contributing to the ambient PM2.5 concentrations at Cheeka Peak Atmospheric Observatory (CPO), Neah Bay WA between January 2011 and December 2014. CPO is home to both an IMPROVE (Interagency Monitoring for Protected Visual Environments) and a NCore multi-pollutant monitoring site. Chemically resolved particulate data from the IMPROVE site was the input data to EPA PMF5.0 and the resulting source factors were derived solely from these data. Solutions from the model were analyzed in context with trace gas and meteorological data collected at the NCore site located roughly 10 m away. Seasonal and long-term trends were analyzed for all five factors and provide the first complete source apportionment analysis of PM2.5 at this remote location. The first factor, identified as marine-traffic residual fuel oil (RFO), was the highest contributor to PM2.5 during late summer. Over the 4-year analysis, the RFO percent contribution to total PM2.5 declined. This is consistent with previous studies and may be attributed to regulations restricting the sulfur content of ship fuel. Biomass combustion emissions (BMC) and sea salt were the largest PM2.5 sources observed at CPO in winter, accounting for over 80% of the fine particulate. BMC accounted for a large percent of the fine particulate pollution when winds were easterly, or continental. Sea salt was the dominant winter factor when winds blew from the west. Measured trace carbon monoxide (CO) and reactive nitrogen species (NOy) were most strongly correlated with the BMC factor and continental winds. The fourth factor was identified as aged crustal material, or dust. In all three years, dust peaked in the spring and was associated exclusively with north-easterly winds. The last factor was identified as aged sea salt mixed with nitrate, sulfate, and other components common to RFO and BMC source factors. It did not exhibit a strong seasonal cycle or dependence on wind direction.

Assessment of light extinction at a European polluted urban area during wintertime: Impact of PM1 composition and sources.

PubMed

Vecchi, R; Bernardoni, V; Valentini, S; Piazzalunga, A; Fermo, P; Valli, G

2018-02-01

In this paper, results from receptor modelling performed on a well-characterised PM 1 dataset were combined to chemical light extinction data (b ext ) with the aim of assessing the impact of different PM 1 components and sources on light extinction and visibility at a European polluted urban area. It is noteworthy that, at the state of the art, there are still very few papers estimating the impact of different emission sources on light extinction as we present here, although being among the major environmental challenges at many polluted areas. Following the concept of the well-known IMPROVE algorithm, here a tailored site-specific approach (recently developed by our group) was applied to assess chemical light extinction due to PM 1 components and major sources. PM 1 samples collected separately during daytime and nighttime at the urban area of Milan (Italy) were chemically characterised for elements, major ions, elemental and organic carbon, and levoglucosan. Chemical light extinction was estimated and results showed that at the investigated urban site it is heavily impacted by ammonium nitrate and organic matter. Receptor modelling (i.e. Positive Matrix Factorization, EPA-PMF 5.0) was effective to obtain source apportionment; the most reliable solution was found with 7 factors which were tentatively assigned to nitrates, sulphates, wood burning, traffic, industry, fine dust, and a Pb-rich source. The apportionment of aerosol light extinction (b ext,aer ) according to resolved sources showed that considering all samples together nitrate contributed at most (on average 41.6%), followed by sulphate, traffic, and wood burning accounting for 18.3%, 17.8% and 12.4%, respectively. Copyright © 2017 Elsevier Ltd. All rights reserved.

Simultaneous aerosol mass spectrometry and chemical ionisation mass spectrometry measurements during a biomass burning event in the UK: insights into nitrate chemistry

NASA Astrophysics Data System (ADS)

Reyes-Villegas, Ernesto; Priestley, Michael; Ting, Yu-Chieh; Haslett, Sophie; Bannan, Thomas; Le Breton, Michael; Williams, Paul I.; Bacak, Asan; Flynn, Michael J.; Coe, Hugh; Percival, Carl; Allan, James D.

2018-03-01

Over the past decade, there has been an increasing interest in short-term events that negatively affect air quality such as bonfires and fireworks. High aerosol and gas concentrations generated from public bonfires or fireworks were measured in order to understand the night-time chemical processes and their atmospheric implications. Nitrogen chemistry was observed during Bonfire Night with nitrogen containing compounds in both gas and aerosol phases and further N2O5 and ClNO2 concentrations, which depleted early next morning due to photolysis of NO3 radicals and ceasing production. Particulate organic oxides of nitrogen (PONs) concentrations of 2.8 µg m-3 were estimated using the m / z 46 : 30 ratios from aerosol mass spectrometer (AMS) measurements, according to previously published methods. Multilinear engine 2 (ME-2) source apportionment was performed to determine organic aerosol (OA) concentrations from different sources after modifying the fragmentation table and it was possible to identify two PON factors representing primary (pPON_ME2) and secondary (sPON_ME2) contributions. A slight improvement in the agreement between the source apportionment of the AMS and a collocated AE-31 Aethalometer was observed after modifying the prescribed fragmentation in the AMS organic spectrum (the fragmentation table) to determine PON sources, which resulted in an r2 = 0.894 between biomass burning organic aerosol (BBOA) and babs_470wb compared to an r2 = 0.861 obtained without the modification. Correlations between OA sources and measurements made using time-of-flight chemical ionisation mass spectrometry with an iodide adduct ion were performed in order to determine possible gas tracers to be used in future ME-2 analyses to constrain solutions. During Bonfire Night, strong correlations (r2) were observed between BBOA and methacrylic acid (0.92), acrylic acid (0.90), nitrous acid (0.86), propionic acid, (0.85) and hydrogen cyanide (0.76). A series of oxygenated species and chlorine compounds showed good correlations with sPON_ME2 and the low volatility oxygenated organic aerosol (LVOOA) factor during Bonfire Night and an event with low pollutant concentrations. Further analysis of pPON_ME2 and sPON_ME2 was performed in order to determine whether these PON sources absorb light near the UV region using an Aethalometer. This hypothesis was tested by doing multilinear regressions between babs_470wb and BBOA, sPON_ME2 and pPON_ME2. Our results suggest that sPON_ME2 does not absorb light at 470 nm, while pPON_ME2 and LVOOA do absorb light at 470 nm. This may inform black carbon (BC) source apportionment studies from Aethalometer measurements, through investigation of the brown carbon contribution to babs_470wb.

Source apportionment of PAHs and n-alkanes bound to PM1 collected near the Venice highway.

PubMed

Valotto, Gabrio; Rampazzo, Giancarlo; Gonella, Francesco; Formenton, Gianni; Ficotto, Silvia; Giraldo, Giorgia

2017-04-01

n-Alkanes and polycyclic aromatic hydrocarbons (PAHs) bound to atmospheric particulate matter (PM 1 ) were investigated in a traffic site located in an urban area of Venice Province (Eastern Po Valley, Italy) during the cold season. Considering the critical situation affecting the Veneto Region concerning the atmospheric pollution and the general lack of information on PM 1 composition and emission in this area, this experimental study aims at determining the source profile, their relative contributions and the dispersion of finer particles. Four sources were identified and quantified using the Positive Matrix Factorization receptor model: (1) mixed combustions related to the residential activities, (2) agricultural biomass burning in addition to the resuspension of anthropogenic and natural debris carried by the wind, (3) gasoline and (4) diesel traffic-related combustions. The role of local atmospheric circulation was also investigated to identify the pollutant sources. Copyright © 2016. Published by Elsevier B.V.

Fine particulate matter (PM2.5) in Edmonton, Canada: Source apportionment and potential risk for human health.

PubMed

Bari, Md Aynul; Kindzierski, Warren B

2016-11-01

To design effective PM 2.5 control strategies in urban centers, there is a need to better understand local and remote sources influencing PM 2.5 levels and associated risk to public health. An investigation of PM 2.5 levels, sources and potential human health risk associated with trace elements in the PM 2.5 was undertaken in Edmonton over a 6-year period (September 2009-August 2015). The geometric mean PM 2.5 concentration of was 7.11 μg/m 3 (interquartile range, IQR = 4.83-10.08 μg/m 3 ). Positive matrix factorization (PMF) receptor modeling identified secondary organic aerosol (SOA) as the major contributor (2.2 μg/m 3 , 27%), followed by secondary nitrate (1.3 μg/m 3 , 17%) and secondary sulfate (1.2 μg/m 3 , 15%). Other local sources included transportation (1.1 μg/m 3 , 14%) and industry-related emissions (0.26 μg/m 3 , 3.4%), biomass burning (1.0 μg/m 3 , 13%) and soil (0.54 μg/m 3 , 6.8%). Five factors (i.e., SOA, secondary nitrate, secondary sulfate, transportation and biomass burning) contributed more than 85% to PM 2.5 for the 2009-2015 period. Geometric (arithmetic) mean and maximum ambient air concentrations for hazardous trace elements of public health concern in PM 2.5 during the study period were below United States regulatory agency chronic and acute health risk screening criteria. Carcinogenic and non-carcinogenic risk of trace elements and source-specific risk values were well below acceptable and safe levels of risks recommended by regulatory agencies. More work is needed to understand the origin of potential SOA and wintertime wood burning sources in Edmonton and the surrounding region and to apply source-risk apportionment using all available hazardous air pollutants (HAPs) including organic compounds to better interpret the potential health risk posed by various sources in urban areas. Copyright © 2016 Elsevier Ltd. All rights reserved.

[Application of ICP-MS and ICP-AES for Studying on Source Apportionment of PM2.5 during Haze Weather in Urban Beijing].

PubMed

Chen, Xi; Du, Peng; Guan, Qing; Feng, Xu; Xu, Dong-qun; Lin, Shao-bin

2015-06-01

To investigate the characteristics of chemical constitute and pollution sources of aerosol fine particulate matter during haze-fog day in Beijing in winter 2013. The samples of PM2.5 were collected in Beijing from January to February, 2013. The technique of ICP-MS and ICP-AES coupled with procedure of bathing-ultrasonic extraction was applied to determine the concentration of 40 elements in the aerosol samples to analyze the characteristics of elements distribution statistically. The absolute principal factor method was used to apportion the pollution sources of PM2.5 during the haze weather in Beijing city in winter 2013. The results showed that during the period of sampling, the volume concentration of Li, Mn, Pb, S etc. obeyed normal distribution approximately, and according to National Ambient Air Quality Standard issued by Ministry of Environmental Protection of the People's Republic of China, the geometric mean concentration of As was twice the annual limit of standard reference, while Pb of some aerosol samples beyond the annual limit of standard reference respectively. The mass fraction of Fe, Zn, Pb, Ti accounted for over 0.1%, while that of Mn, Cu, As, Se etc. 0.01%. These elements were primary inorganic pollutants, and especially the hazards and sources of As and Pb should be concerned. There were 6 main pollution sources were chosen by the factor analysis method, including industrial dust and human beings activities, biomass combustion and building dust, soil and sand dusts, fossil fuel, electronic waste and metal smelting, with the variance contribution rate of 40.3%, 27.0%, 9.1%, 4.9%, 4.8% and 4.6% respectively. ICP-MS and ICP-AES can be applied to analyzing multi-elements in PM2.5 accurately and quickly to facilitate source apportionment, and it indicated that the relevant pollution sources should be considered and the effect of regional transferring of haze pollution sources should be taken into account, and specific measures should be taken for control.

Source apportionment analysis of air pollutants using CMAQ/BFM for national air quality management policy over Republic of Korea.

NASA Astrophysics Data System (ADS)

Moon, N.; Kim, S.; Seo, J.; Lee, Y. J.

2017-12-01

Recently, the Korean government is focusing on solving air pollution problem such as fine particulate matter and ozone. Korea has high population density and concentrated industrial complex in its limited land space. For better air quality management, it is important to understand source and contribution relation to target pollutant. The air quality analysis representing the mutual contribution among the local regions enables to understand the substantive state of the air quality of a region in association with neighboring regions. Under this background, the source apportionment of PM10, PM2.5, O3, NO2, SO2 using WRF and CMAQ/BFM was analyzed over Korea and BFM was applied to mobile, area and point sources in each local government. The contribution rate from neighboring region showed different pattern for each pollutant. In case of primary pollutants such as NO2, SO2, local source contribution is dominant, on the other hand secondary pollutants case especially O3, contribution from neighboring region is higher than that from source region itself. Local source contribution to PM10 showed 20-25% and the contribution rate to O3 has big difference with different meteorological condition year after year. From this study, we tried to estimate the conversion rate between source (NOx, VOC, SO2, NH3, PMC, PM2.5, CO) and concentration (PM10, PM2.5, O3, NO2, SO2,) by regional group over Korea. The result can contribute to the decision-making process of important national planning related to large-scale industrial developments and energy supply policies (eg., operations of coal-fired power plants and diesel cars) and emission control plan, where many controversies and concerns are currently concentrated among local governments in Korea. With this kind of approach, various environmental and social problems related to air quality can also be identified early so that a sustainable and environmentally sound plan can be established by providing data infrastructures to be utilized by central government agencies, local governments, and even private sectors.

Pollution characteristics, source apportionment, and health risk of heavy metals in street dust of Suzhou, China.

PubMed

Lin, Manli; Gui, Herong; Wang, Yao; Peng, Weihua

2017-01-01

To analyze the pollution characteristics, source apportionment, and health risk of heavy metals (HMs) in street dust of Suzhou, China, 23 sampling sites were selected and periodically sampled for 12 months. A total of 276 samples were collected, and the concentrations of selected HMs (e.g., Cr, Cu, Fe, Mn, Pb, V, and Zn) were examined with an X-ray fluorescence spectrum analyzer. Results showed that the mean concentrations of Cr, Cu, Fe, Mn, Pb, V, and Zn in the street dust of Suzhou were 112.9, 27.5, 19941.3, 410.3, 45.2, 75.6, and 225.3 mg kg -1 , respectively. Cr, Cu, Pb, and Zn exceeded their background values in local natural soils by 1.3-3.6-fold, whereas Fe, Mn, and V were all within their background values. However, enrichment factor analysis revealed that Cr, Cu, Mn, Pb, V, and Zn, especially Cr, Cu, Pb, and Zn, were enriched in Suzhou street dust. The HMs showed no significant seasonal changes overall, but spatial distribution analysis implied that the high values of Cr, Cu, Mn, Pb, V, and Zn were mainly distributed in areas with frequent human activities. Results of multivariate techniques (e.g., Pearson correlation, hierarchical cluster, and principal components analyses) suggested that Pb and Zn had complicated sources; Cu and V mainly originated from traffic sources; Fe and Mn mainly came from natural sources; and Cr was dominantly related to industrial district. Health risk assessment revealed that a single heavy metal might not cause both non-cancer and carcinogenic risks to local residents. Nevertheless, the sum of the hazard index of all selected HMs for children slightly exceeded the safety value, thereby implying that the HMs from Suzhou street dust can possibly produce significant risk to children. Cr was the priority pollutant in the study area because of its high concentration, high enrichment, and high contribution to non-cancer risk values.

Source apportionments of PM2.5 organic carbon using molecular marker Positive Matrix Factorization and comparison of results from different receptor models

NASA Astrophysics Data System (ADS)

Heo, Jongbae; Dulger, Muaz; Olson, Michael R.; McGinnis, Jerome E.; Shelton, Brandon R.; Matsunaga, Aiko; Sioutas, Constantinos; Schauer, James J.

2013-07-01

Four hundred fine particulate matter (PM2.5) samples collected over a 1-year period at two sites in the Los Angeles Basin were analyzed for organic carbon (OC), elemental carbon (EC), water soluble organic carbon (WSOC) and organic molecular markers. The results were used in a Positive Matrix Factorization (PMF) receptor model to obtain daily, monthly and annual average source contributions to PM2.5 OC. Results of the PMF model showed similar source categories with comparable year-long contributions to PM2.5 OC across the sites. Five source categories providing reasonably stable profiles were identified: mobile, wood smoke, primary biogenic, and two types of secondary organic carbon (SOC) (i.e., anthropogenic and biogenic emissions). Total primary emission factors and total SOC factors contributed approximately 60% and 40%, respectively, to the annual-average OC concentrations. Primary sources showed strong seasonal patterns with high winter peaks and low summer peaks, while SOC showed a reverse pattern with highs in the spring and summer in the region. Interestingly, smoke from forest fires which occurred episodically in California during the summer and fall of 2009 was identified and combined with the primary biogenic source as one distinct factor to the OC budget. The PMF resolved factors were further investigated and compared to a chemical mass balance (CMB) model and a second multi-variant receptor model (UNMIX) using molecular markers considered in the PMF. Good agreement between the source contribution from mobile sources and biomass burning for three models were obtained, providing additional weight of evidence that these source apportionment techniques are sufficiently accurate for policy development. However, the CMB model did not quantify primary biogenic emissions, which were included in other sources with the SOC. Both multivariate receptor models, the PMF and the UNMIX, were unable to separate source contributions from diesel and gasoline engines.

Air quality in the German-Czech border region: A focus on harmful fractions of PM and ultrafine particles

NASA Astrophysics Data System (ADS)

Schladitz, Alexander; Leníček, Jan; Beneš, Ivan; Kováč, Martin; Skorkovský, Jiří; Soukup, Aleš; Jandlová, Jana; Poulain, Laurent; Plachá, Helena; Löschau, Gunter; Wiedensohler, Alfred

2015-12-01

A comprehensive air quality study has been carried out at two urban background sites in Annaberg-Buchholz (Germany) and Ústí nad Labem (Czech Republic) in the German-Czech border region between January 2012 and June 2014. Special attention was paid to quantify harmful fractions of particulate matter (PM) and ultrafine particle number concentration (UFP) from solid fuel combustion and vehicular traffic. Source type contributions of UFP were quantified by using the daily concentration courses of UFP and nitrogen oxide. Two different source apportionment techniques were used to quantify relative and absolute mass contributions: positive matrix factorization for total PM2.5 and elemental carbon in PM2.5 and chemical mass balance for total PM1 and organic carbon in PM1. Contributions from solid fuel combustion strongly differed between the non-heating period (April-September) and the heating period (October-March). Major sources of solid fuel combustion in this study were wood and domestic coal combustion, while the proportion of industrial coal combustion was low (<3%). In Ústí nad Labem combustion of domestic brown coal was the most important source of organic carbon ranging from 34% to 43%. Wood combustion was an important source of organic carbon in Annaberg-Buchholz throughout the year. Heavy metals and less volatile polycyclic aromatic hydrocarbons (PAH) in the accumulation mode were related to solid fuel combustion with enhanced concentrations during the heating period. In contrast, vehicular PAH emissions were allocated to the Aitken mode. Only in Ústí nad Labem a significant contribution of photochemical new particle formation (e.g. from sulfur dioxide) to UFP of almost 50% was observed during noontime. UFPs from traffic emissions (nucleation particles) and primary emitted soot particles dominated at both sites during the rest of the day. The methodology of a combined source apportionment of UFP and PM can be adapted to other regions of the world with similar problems of atmospheric pollution to calculate the relative risk in epidemiological health studies for different sub-fractions of PM and UFP. This will enhance the meaningfulness of published relative risks in health studies based on total PM and UFP number concentrations.

Wood burning pollution in southern Chile: PM2.5 source apportionment using CMB and molecular markers.

PubMed

Villalobos, Ana M; Barraza, Francisco; Jorquera, Héctor; Schauer, James J

2017-06-01

Temuco is a mid-size city representative of severe wood smoke pollution in southern Chile; i.e., ambient 24-h PM 2.5 concentrations have exceeded 150 μg/m 3 in the winter season and the top concentration reached 372 μg/m 3 in 2010. Annual mean concentrations have decreased but are still above 30 μg/m 3 . For the very first time, a molecular marker source apportionment of ambient organic carbon (OC) and PM 2.5 was conducted in Temuco. Primary resolved sources for PM 2.5 were wood smoke (37.5%), coal combustion (4.4%), diesel vehicles (3.3%), dust (2.2%) and vegetative detritus (0.7%). Secondary inorganic PM 2.5 (sulfates, nitrates and ammonium) contributed 4.8% and unresolved organic aerosols (generated from volatile emissions from incomplete wood combustion), including secondary organic aerosols, contributed 47.1%. Adding the contributions of unresolved organic aerosols to those from primary wood smoke implies that wood burning is responsible for 84.6% of the ambient PM 2.5 in Temuco. This predominance of wood smoke is ultimately due to widespread poverty and a lack of efficient household heating methods. The government has been implementing emission abatement policies but achieving compliance with ambient air quality standards for PM 2.5 in southern Chile remains a challenge. Copyright © 2017 Elsevier Ltd. All rights reserved.

Application of the ReNuMa model in the Sha He river watershed: tools for watershed environmental management.

PubMed

Sha, Jian; Liu, Min; Wang, Dong; Swaney, Dennis P; Wang, Yuqiu

2013-07-30

Models and related analytical methods are critical tools for use in modern watershed management. A modeling approach for quantifying the source apportionment of dissolved nitrogen (DN) and associated tools for examining the sensitivity and uncertainty of the model estimates were assessed for the Sha He River (SHR) watershed in China. The Regional Nutrient Management model (ReNuMa) was used to infer the primary sources of DN in the SHR watershed. This model is based on the Generalized Watershed Loading Functions (GWLF) and the Net Anthropogenic Nutrient Input (NANI) framework, modified to improve the characterization of subsurface hydrology and septic system loads. Hydrochemical processes of the SHR watershed, including streamflow, DN load fluxes, and corresponding DN concentration responses, were simulated following calibrations against observations of streamflow and DN fluxes. Uncertainty analyses were conducted with a Monte Carlo analysis to vary model parameters for assessing the associated variations in model outputs. The model performed accurately at the watershed scale and provided estimates of monthly streamflows and nutrient loads as well as DN source apportionments. The simulations identified the dominant contribution of agricultural land use and significant monthly variations. These results provide valuable support for science-based watershed management decisions and indicate the utility of ReNuMa for such applications. Copyright © 2013 Elsevier Ltd. All rights reserved.

Source apportionment of fine particles and its chemical components over the Yangtze River Delta, China during a heavy haze pollution episode

NASA Astrophysics Data System (ADS)

Li, L.; An, J. Y.; Zhou, M.; Yan, R. S.; Huang, C.; Lu, Q.; Lin, L.; Wang, Y. J.; Tao, S. K.; Qiao, L. P.; Zhu, S. H.; Chen, C. H.

2015-12-01

An extremely high PM2.5 pollution episode occurred over the eastern China in January 2013. In this paper, the particulate matter source apportionment technology (PSAT) method coupled within the Comprehensive air quality model with extensions (CAMx) is applied to study the source contributions to PM2.5 and its major components at six receptors (Urban Shanghai, Chongming, Dianshan Lake, Urban Suzhou, Hangzhou and Zhoushan) in the Yangtze River Delta (YRD) region. Contributions from 4 source areas (including Shanghai, South Jiangsu, North Zhejiang and Super-region) and 9 emission sectors (including power plants, industrial boilers and kilns, industrial processing, mobile source, residential, volatile emissions, dust, agriculture and biogenic emissions) to PM2.5 and its major components (sulfate, nitrate, ammonia, organic carbon and elemental carbon) at the six receptors in the YRD region are quantified. Results show that accumulation of local pollution was the largest contributor during this air pollution episode in urban Shanghai (55%) and Suzhou (46%), followed by long-range transport (37% contribution to Shanghai and 44% to Suzhou). Super-regional emissions play an important role in PM2.5 formation at Hangzhou (48%) and Zhoushan site (68%). Among the emission sectors contributing to the high pollution episode, the major source categories include industrial processing (with contributions ranging between 12.7 and 38.7% at different receptors), combustion source (21.7-37.3%), mobile source (7.5-17.7%) and fugitive dust (8.4-27.3%). Agricultural contribution is also very significant at Zhoushan site (24.5%). In terms of the PM2.5 major components, it is found that industrial boilers and kilns are the major source contributor to sulfate and nitrate. Volatile emission source and agriculture are the major contributors to ammonia; transport is the largest contributor to elemental carbon. Industrial processing, volatile emissions and mobile source are the most significant contributors to organic carbon. Results show that the Yangtze River Delta region should focus on the joint pollution control of industrial processing, combustion emissions, mobile source emissions, and fugitive dust. Regional transport of air pollution among the cities are prominent, and the implementation of regional joint prevention and control of air pollution will help to alleviate fine particulate matter concentrations under heavy pollution case significantly.

Source apportionment of PM2.5 carbonaceous aerosol in Baghdad, Iraq

NASA Astrophysics Data System (ADS)

Hamad, Samera Hussein; Schauer, James Jay; Heo, Jongbae; Kadhim, Ahmed K. H.

2015-04-01

Baghdad is the second largest city in the Middle East and suffers from severe air quality degradation due to the high levels of the atmospheric particulate matter (PM). Limited information exists regarding the sources of PM in Baghdad, and the lack of information on sources inhibits the development of control strategies to reduce air pollution. To better understand the nature of fine particulate matter (PM2.5) in Baghdad and the Middle East, a one year sampling campaign to collect PM2.5 was conducted from September 2012 through September 2013, missing August 2013 samples due to the security situation. 24-hour integrated samples collected on a 1-in-6 day schedule were analyzed for the major components, and monthly average samples were analyzed by gas chromatography mass spectrometry (GCMS) methods to measure particle-phase organic molecular markers. The results of organic molecular markers were used in a chemical mass balance (CMB) model to quantify the sources of PM2.5 organic carbon (OC) and PM2.5 mass. Primary sources accounted for 44% of the measured PM2.5, and secondary sources were estimated to make up 28% of the measured PM2.5. Picene, a tracer of coal combustion detected in Baghdad where there is no evidence for coal combustion, can be attributed to burning crude oil and other low quality fuels in Baghdad. Source apportionment results showed that the dominant sources of the carbonaceous aerosols in Baghdad are gasoline (37 ± 6%) and diesel engines (17 ± 3%) which can be attributed to the extensive use of gasoline and diesel powered generators in Baghdad. Wood burning and residual oil combustion contributed to 5 ± 0.4 and 1 ± 0.2% respectively of OC. The unresolved sources contributed to 42 ± 19% of the OC which represented the secondary organic aerosol (SOA) and the unidentified sources.

Pollution characteristics, risk assessment, and source apportionment of heavy metals in road dust in Beijing, China.

PubMed

Men, Cong; Liu, Ruimin; Xu, Fei; Wang, Qingrui; Guo, Lijia; Shen, Zhenyao

2018-01-15

To analyze the spatial distribution patterns, risks, and sources of heavy metals (As, Cd, Cr, Cu, Hg, Mn, Ni, Pb, Zn, Fe), 36 road dust samples were collected from an urbanized area of Beijing in June 2016. The mean concentration of most metals, except As and Mn, exceeded their corresponding background values, with the mean concentration of Cd being 8 times that of its background. Spatially, for most heavy metals, except As and Mn, the high concentration areas were mainly within the 5th ring road, especially the northern area. The geo-accumulation index of Cd and Cu indicated moderate contamination at many sites. The entire study area was prone to potential ecological risks, with higher risks within the 4th ring road. Cd caused high potential ecological risk at most sites. According to the health risk assessment results, the non-carcinogenic risks that human beings suffered from heavy metals were insignificant. However, the carcinogenic risks due to Ni and Cr exceeded the acceptable level. Based on the source apportionment using positive matrix factorization, four factors were defined for the heavy metals. Factor 1, which was traffic-related exhaust, accounted for 34.47% of the concentration of heavy metals. The contributions of Factors 2 and 3 were approximately 25% each. Factor 2 was potentially related to coal combustion, while Factor 3 could be related to the manufacture and use of metal components. Factor 4, which could be related to the use of pesticides, fertilizers, and medical devices, accounted for 14.88%, which was the lowest. Copyright © 2017 Elsevier B.V. All rights reserved.

Source apportionments of aerosols and their direct radiative forcing and long-term trends over continental United States

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Yang; Wang, Hailong; Smith, Steven J.

Due to US air pollution regulations, aerosol and precursor emissions have decreased during recent decades, while changes in emissions in other regions of the world also influence US aerosol trends through long-range transport. We examine here the relative roles of these domestic and foreign emission changes on aerosol concentrations and direct radiative forcing (DRF) at the top of the atmosphere over the continental US. Long-term (1980-2014) trends and aerosol source apportionment are quantified in this study using a global aerosol-climate model equipped with an explicit aerosol source tagging technique. Due to US emission control policies, the annual mean near-surface concentrationmore » of particles, consisting of sulfate, black carbon, and primary organic aerosol, decreases by about –1.1 (±0.1) / –1.4 (±0.1) μg m -3 in western US and –3.3 (±0.2) / –2.9 (±0.2) μg m -3 in eastern US during 2010–2014, as compared to those in 1980–1984. Meanwhile, decreases in US emissions lead to a warming of +0.48 (±0.03) / –0.46 (±0.03) W m -2 in western US and +1.41 (±0.07) /+1.32 (±0.09) W m -2 in eastern US through changes in aerosol DRF. Increases in emissions from East Asia generally have a modest impact on US air quality, but mitigated the warming effect induced by reductions in US emissions by 25% in western US and 7% in eastern US. Thus, as US domestic aerosol and precursor emissions continue to decrease, foreign emissions may become increasingly important to radiative forcing over the US.« less

Source apportionments of aerosols and their direct radiative forcing and long-term trends over continental United States

DOE PAGES

Yang, Yang; Wang, Hailong; Smith, Steven J.; ...

2018-05-23

Due to US air pollution regulations, aerosol and precursor emissions have decreased during recent decades, while changes in emissions in other regions of the world also influence US aerosol trends through long-range transport. We examine here the relative roles of these domestic and foreign emission changes on aerosol concentrations and direct radiative forcing (DRF) at the top of the atmosphere over the continental US. Long-term (1980-2014) trends and aerosol source apportionment are quantified in this study using a global aerosol-climate model equipped with an explicit aerosol source tagging technique. Due to US emission control policies, the annual mean near-surface concentrationmore » of particles, consisting of sulfate, black carbon, and primary organic aerosol, decreases by about –1.1 (±0.1) / –1.4 (±0.1) μg m -3 in western US and –3.3 (±0.2) / –2.9 (±0.2) μg m -3 in eastern US during 2010–2014, as compared to those in 1980–1984. Meanwhile, decreases in US emissions lead to a warming of +0.48 (±0.03) / –0.46 (±0.03) W m -2 in western US and +1.41 (±0.07) /+1.32 (±0.09) W m -2 in eastern US through changes in aerosol DRF. Increases in emissions from East Asia generally have a modest impact on US air quality, but mitigated the warming effect induced by reductions in US emissions by 25% in western US and 7% in eastern US. Thus, as US domestic aerosol and precursor emissions continue to decrease, foreign emissions may become increasingly important to radiative forcing over the US.« less

Do vehicular emissions dominate the source of C6-C8 aromatics in the megacity Shanghai of eastern China?

PubMed

Wang, Hongli; Wang, Qian; Chen, Jianmin; Chen, Changhong; Huang, Cheng; Qiao, Liping; Lou, Shengrong; Lu, Jun

2015-01-01

The characteristic ratios of volatile organic compounds (VOCs) to i-pentane, the indicator of vehicular emissions, were employed to apportion the vehicular and non-vehicular contributions to reactive species in urban Shanghai. Two kinds of tunnel experiments, one tunnel with more than 90% light duty gasoline vehicles and the other with more than 60% light duty diesel vehicles, were carried out to study the characteristic ratios of vehicle-related emissions from December 2009 to January 2010. Based on the experiments, the characteristic ratios of C6-C8 aromatics to i-pentane of vehicular emissions were 0.53 ± 0.08 (benzene), 0.70 ± 0.12 (toluene), 0.41 ± 0.09 (m,p-xylenes), 0.16 ± 0.04 (o-xylene), 0.023 ± 0.011 (styrene), and 0.15 ± 0.02 (ethylbenzene), respectively. The source apportionment results showed that around 23.3% of C6-C8 aromatics in urban Shanghai were from vehicular emissions, which meant that the non-vehicular emissions had more importance. These findings suggested that emission control of non-vehicular sources, i.e. industrial emissions, should also receive attention in addition to the control of vehicle-related emissions in Shanghai. The chemical removal of VOCs during the transport from emissions to the receptor site had a large impact on the apportionment results. Generally, the overestimation of vehicular contributions would occur when the VOC reaction rate constant with OH radicals (kOH) was larger than that of the vehicular indicator, while for species with smaller kOH than the vehicular indicator, the vehicular contribution would be underestimated by the method of characteristic ratios. Copyright © 2014. Published by Elsevier B.V.

Sediment source fingerprinting as an aid to catchment management: A review of the current state of knowledge and a methodological decision-tree for end-users.

PubMed

Collins, A L; Pulley, S; Foster, I D L; Gellis, A; Porto, P; Horowitz, A J

2017-06-01

The growing awareness of the environmental significance of fine-grained sediment fluxes through catchment systems continues to underscore the need for reliable information on the principal sources of this material. Source estimates are difficult to obtain using traditional monitoring techniques, but sediment source fingerprinting or tracing procedures, have emerged as a potentially valuable alternative. Despite the rapidly increasing numbers of studies reporting the use of sediment source fingerprinting, several key challenges and uncertainties continue to hamper consensus among the international scientific community on key components of the existing methodological procedures. Accordingly, this contribution reviews and presents recent developments for several key aspects of fingerprinting, namely: sediment source classification, catchment source and target sediment sampling, tracer selection, grain size issues, tracer conservatism, source apportionment modelling, and assessment of source predictions using artificial mixtures. Finally, a decision-tree representing the current state of knowledge is presented, to guide end-users in applying the fingerprinting approach. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

Reliability apportionment approach for spacecraft solar array using fuzzy reasoning Petri net and fuzzy comprehensive evaluation

NASA Astrophysics Data System (ADS)

Wu, Jianing; Yan, Shaoze; Xie, Liyang; Gao, Peng

2012-07-01

The reliability apportionment of spacecraft solar array is of significant importance for spacecraft designers in the early stage of design. However, it is difficult to use the existing methods to resolve reliability apportionment problem because of the data insufficiency and the uncertainty of the relations among the components in the mechanical system. This paper proposes a new method which combines the fuzzy comprehensive evaluation with fuzzy reasoning Petri net (FRPN) to accomplish the reliability apportionment of the solar array. The proposed method extends the previous fuzzy methods and focuses on the characteristics of the subsystems and the intrinsic associations among the components. The analysis results show that the synchronization mechanism may obtain the highest reliability value and the solar panels and hinges may get the lowest reliability before design and manufacturing. Our developed method is of practical significance for the reliability apportionment of solar array where the design information has not been clearly identified, particularly in early stage of design.

Measuring the Wealth of School Districts for the Apportionment of Aid to Public Schools in New York State: Full Valuation vs. Personal Income.

ERIC Educational Resources Information Center

New York State Div. of the Budget, Albany.

The purpose of this study was to assess the merit of using personal income in the determination of a school district's fiscal capacity for the apportionment of New York state aid. Both personal income and full valuation of real property suffer from technical weaknesses, but improvements in the data are possible if the state is willing to…

Quantifying road dust resuspension in urban environment by Multilinear Engine: A comparison with PMF2

NASA Astrophysics Data System (ADS)

Amato, F.; Pandolfi, M.; Escrig, A.; Querol, X.; Alastuey, A.; Pey, J.; Perez, N.; Hopke, P. K.

Atmospheric PM pollution from traffic comprises not only direct emissions but also non-exhaust emissions because resuspension of road dust that can produce high human exposure to heavy metals, metalloids, and mineral matter. A key task for establishing mitigation or preventive measures is estimating the contribution of road dust resuspension to the atmospheric PM mixture. Several source apportionment studies, applying receptor modeling at urban background sites, have shown the difficulty in identifying a road dust source separately from other mineral sources or vehicular exhausts. The Multilinear Engine (ME-2) is a computer program that can solve the Positive Matrix Factorization (PMF) problem. ME-2 uses a programming language permitting the solution to be guided toward some possible targets that can be derived from a priori knowledge of sources (chemical profile, ratios, etc.). This feature makes it especially suitable for source apportionment studies where partial knowledge of the sources is available. In the present study ME-2 was applied to data from an urban background site of Barcelona (Spain) to quantify the contribution of road dust resuspension to PM 10 and PM 2.5 concentrations. Given that recently the emission profile of local resuspended road dust was obtained (Amato, F., Pandolfi, M., Viana, M., Querol, X., Alastuey, A., Moreno, T., 2009. Spatial and chemical patterns of PM 10 in road dust deposited in urban environment. Atmospheric Environment 43 (9), 1650-1659), such a priori information was introduced in the model as auxiliary terms of the object function to be minimized by the implementation of the so-called "pulling equations". ME-2 permitted to enhance the basic PMF solution (obtained by PMF2) identifying, beside the seven sources of PMF2, the road dust source which accounted for 6.9 μg m -3 (17%) in PM 10, 2.2 μg m -3 (8%) of PM 2.5 and 0.3 μg m -3 (2%) of PM 1. This reveals that resuspension was responsible of the 37%, 15% and 3% of total traffic emissions respectively in PM 10, PM 2.5 and PM 1. Therefore the overall traffic contribution resulted in 18 μg m -3 (46%) in PM 10, 14 μg m -3 (51%) in PM 2.5 and 8 μg m -3 (48%) in PM 1. In PMF2 this mass explained by road dust resuspension was redistributed among the rest of sources, increasing mostly the mineral, secondary nitrate and aged sea salt contributions.

Source apportionment of PM2.5 for supporting control strategies in the Monterrey Metropolitan Area, Mexico.

PubMed

Martínez-Cinco, Marco; Santos-Guzmán, Jesús; Mejía-Velázquez, Gerardo

2016-06-01

The Monterrey Metropolitan Area (MMA) in Northeast Mexico has shown high PM2.5 concentrations since 2003. The data shows that the annual average concentration exceeds from 2 to 3 times the Mexican PM2.5 annual air quality standard of 12 µg/m(3). In a previous work we studied the chemical characterization of PM2.5 in two sites of the MMA during the winter season. Among the most important components we found ammonium sulfate and nitrate, elemental and organic carbon, and crustal matter. In this work we present the results of a second chemical characterization study performed during the summer time and the application of the chemical mass balance (CMB) model to determine the source apportionment of air pollutants in the region. The chemical analysis results show that the chemical composition of PM2.5 is similar in both sites and periods of the year. The results of the chemical analysis and the CMB model show that industrial, traffic, and combustion activities in the area are the major sources of primary PM2.5 and precursor gases of secondary inorganic and organic aerosol (SO2, NOx, NH3, and volatile organic compounds [VOCs]). We also found that black carbon and organic carbon are important components of PM2.5 in the MMA. These results are consistent with the MMA emission inventory that reports as major sources of particles and SO2 a refinery and fuel combustion, as well as nitrogen oxides and ammonium from transportation and industrial activities in the MMA and ammonium form agricultural activities in the state. The results of this work are important to identify and support effective actions to reduce direct emissions of PM2.5 and its precursor gases to improve air quality in the MMA. The Monterrey Metropolitan Area (MMA) has been classified as the most air-polluted area in Mexico by the World Health Organization (WHO). Effective actions need to be taken to control primary sources of PM2.5 and its precursors, reducing health risks on the population exposed and their associated costs. The results of this study identify the main sources and their estimated contribution to PM2.5 mass concentration, providing valuable information to the local environmental authorities to take decisions on PM2.5 control strategies in the MMA.

Formaldehyde Source Attribution in Houston during TexAQS II and TRAMP

NASA Astrophysics Data System (ADS)

Guven, B.; Olaguer, E. P.

2010-12-01

To determine the relative importance of primary vs secondary formaldehyde in Houston, source apportionment was performed on continuous online measurements of VOCs, formaldehyde (HCHO), CO, SO2, and HONO at one urban and two industrial sites. The results of source apportionment were used in conjunction with the meteorological, emission inventory, emission event, and back trajectory data catalogued in Air Research Information Infrastructure (ARII) to determine the dominant source regions and evaluate the accuracy of reported regular and upset emissions from industrial facilities. The contribution of industrial sources such as flares from petrochemical plants and refineries to total atmospheric formaldehyde concentrations at the urban site is estimated to be 17% compared to 23% for mobile sources, amounting to 40% for the total contribution of primary HCHO sources. The relative contribution of industrial sources to HCHO concentration at the urban site increased to about 66% on some mornings coinciding with the HCHO peak concentrations. Secondary formation of HCHO during the day and night resulted from the reactions of industrial olefins and other VOCs with OH or ozone was a significant contributor to HCHO concentrations at the urban site. An analysis of emission event, back trajectory and ambient concentration data in ARII showed that a large percentage of emission events were associated with trajectories that passed through the two industrial sites when peaks in concentrations were detected at those sites. Some peak HCHO concentrations can also be linked to emission events of other VOCs, while a significant portion remained unexplained by the reported events. It is likely, based on the results from the SHARP campaign and our analysis, that some episodic emission events containing HCHO are unreported to the TCEQ. Overlaid CPF plots for nighttime (green) and daytime (red) HCHO concentrations measured at three sites and the locations of the largest emitting point sources around the sites. Average contributions to formaldehyde concentrations.

Using stable isotopes of hydrogen to quantify biogenic and thermogenic atmospheric methane sources: A case study from the Colorado Front Range

NASA Astrophysics Data System (ADS)

Townsend-Small, Amy; Botner, E. Claire; Jimenez, Kristine L.; Schroeder, Jason R.; Blake, Nicola J.; Meinardi, Simone; Blake, Donald R.; Sive, Barkley C.; Bon, Daniel; Crawford, James H.; Pfister, Gabriele; Flocke, Frank M.

2016-11-01

Global atmospheric concentrations of methane (CH4), a powerful greenhouse gas, are increasing, but because there are many natural and anthropogenic sources of CH4, it is difficult to assess which sources may be increasing in magnitude. Here we present a data set of δ2H-CH4 measurements of individual sources and air in the Colorado Front Range, USA. We show that δ2H-CH4, but not δ13C, signatures are consistent in air sampled downwind of landfills, cattle feedlots, and oil and gas wells in the region. Applying these source signatures to air in ground and aircraft samples indicates that at least 50% of CH4 emitted in the region is biogenic, perhaps because regulatory restrictions on leaking oil and natural gas wells are helping to reduce this source of CH4. Source apportionment tracers such as δ2H may help close the gap between CH4 observations and inventories, which may underestimate biogenic as well as thermogenic sources.

Long-term chemical analysis and organic aerosol source apportionment at nine sites in central Europe: source identification and uncertainty assessment

NASA Astrophysics Data System (ADS)

Daellenbach, Kaspar R.; Stefenelli, Giulia; Bozzetti, Carlo; Vlachou, Athanasia; Fermo, Paola; Gonzalez, Raquel; Piazzalunga, Andrea; Colombi, Cristina; Canonaco, Francesco; Hueglin, Christoph; Kasper-Giebl, Anne; Jaffrezo, Jean-Luc; Bianchi, Federico; Slowik, Jay G.; Baltensperger, Urs; El-Haddad, Imad; Prévôt, André S. H.

2017-11-01

Long-term monitoring of organic aerosol is important for epidemiological studies, validation of atmospheric models, and air quality management. In this study, we apply a recently developed filter-based offline methodology using an aerosol mass spectrometer (AMS) to investigate the regional and seasonal differences of contributing organic aerosol sources. We present offline AMS measurements for particulate matter smaller than 10 µm at nine stations in central Europe with different exposure characteristics for the entire year of 2013 (819 samples). The focus of this study is a detailed source apportionment analysis (using positive matrix factorization, PMF) including in-depth assessment of the related uncertainties. Primary organic aerosol (POA) is separated in three components: hydrocarbon-like OA related to traffic emissions (HOA), cooking OA (COA), and biomass burning OA (BBOA). We observe enhanced production of secondary organic aerosol (SOA) in summer, following the increase in biogenic emissions with temperature (summer oxygenated OA, SOOA). In addition, a SOA component was extracted that correlated with an anthropogenic secondary inorganic species that is dominant in winter (winter oxygenated OA, WOOA). A factor (sulfur-containing organic, SC-OA) explaining sulfur-containing fragments (CH3SO2+), which has an event-driven temporal behaviour, was also identified. The relative yearly average factor contributions range from 4 to 14 % for HOA, from 3 to 11 % for COA, from 11 to 59 % for BBOA, from 5 to 23 % for SC-OA, from 14 to 27 % for WOOA, and from 15 to 38 % for SOOA. The uncertainty of the relative average factor contribution lies between 2 and 12 % of OA. At the sites north of the alpine crest, the sum of HOA, COA, and BBOA (POA) contributes less to OA (POA / OA = 0.3) than at the southern alpine valley sites (0.6). BBOA is the main contributor to POA with 87 % in alpine valleys and 42 % north of the alpine crest. Furthermore, the influence of primary biological particles (PBOAs), not resolved by PMF, is estimated and could contribute significantly to OA in PM10.

50 CFR Table 35 to Part 679 - Apportionment of Crab PSC and Halibut PSC Between the Amendment 80 and BSAI Trawl Limited Access...

Code of Federal Regulations, 2011 CFR

2011-10-01

... 35 to Part 679—Apportionment of Crab PSC and Halibut PSC Between the Amendment 80 and BSAI Trawl Limited Access Sectors Fishery Year Halibut PSC limit in the BSAI Zone 1 Red king crab PSC limit . . . C... 50 Wildlife and Fisheries 11 2011-10-01 2011-10-01 false Apportionment of Crab PSC and Halibut PSC...

50 CFR Table 35 to Part 679 - Apportionment of Crab PSC and Halibut PSC Between the Amendment 80 and BSAI Trawl Limited Access...

Code of Federal Regulations, 2010 CFR

2010-10-01

... 35 to Part 679—Apportionment of Crab PSC and Halibut PSC Between the Amendment 80 and BSAI Trawl Limited Access Sectors Fishery Year Halibut PSC limit in the BSAI Zone 1 Red king crab PSC limit . . . C... 50 Wildlife and Fisheries 9 2010-10-01 2010-10-01 false Apportionment of Crab PSC and Halibut PSC...

Source Apportionment of Final Particulate Matterin North China Plain based on Air Quality Modeling

NASA Astrophysics Data System (ADS)

Xing, J.; Wu, W.; Chang, X.; Wang, S.; Hao, J.

2016-12-01

Most Chinese cities in North China Plain are suffering from serious air pollution. To develop the regional air pollution control policies, we need to identify the major source contributions to such pollution and to design the control policy which is accurate, efficient and effective. This study used the air quality model with serval advanced technologies including ISAM and ERSM, to assess the source contributions from individual pollutants (incl. SO2, NOx, VOC, NH3, primary PM), sectors (incl. power plants, industry, transportation and domestic), and regions (Beijing, Hebei, Tianjing and surrounding provinces). The modeling period is two months in 2012 as January and July which represent winter and summer respectively. The non-linear relationship between air pollutant emissions and air quality will be addressed, and the integrated control of multi-pollutants and multi-regions in China will be suggested.

Inter-comparison of source apportionment of PM10 using PMF and CMB in three sites nearby an industrial area in central Italy

NASA Astrophysics Data System (ADS)

Cesari, Daniela; Donateo, Antonio; Conte, Marianna; Contini, Daniele

2016-12-01

Receptor models (RMs), based on chemical composition of particulate matter (PM), such as Chemical Mass Balance (CMB) and Positive Matrix Factorization (PMF), represent useful tools for determining the impact of PM sources to air quality. This information is useful, especially in areas influenced by anthropogenic activities, to plan mitigation strategies for environmental management. Recent inter-comparison of source apportionment (SA) results showed that one of the difficulties in the comparison of estimated source contributions is the compatibility of the sources, i.e. the chemical profiles of factor/sources used in receptor models. This suggests that SA based on integration of several RMs could give more stable and reliable solutions with respect to a single model. The aim of this work was to perform inter-comparison of PMF (using PMF3.0 and PMF5.0 codes) and CMB outputs, focusing on both source chemical profiles and estimates of source contributions. The dataset included 347 daily PM10 samples collected in three sites in central Italy located near industrial emissions. Samples were chemically analysed for the concentrations of 21 chemical species (NH4+, Ca2 +, Mg2 +, Na+, K+, Mg2 +, SO42 -, NO3-, Cl-, Si, Al, Ti, V, Mn, Fe, Ni, Cu, Zn, Br, EC, and OC) used as input of RMs. The approach identified 9 factor/sources: marine, traffic, resuspended dust, biomass burning, secondary sulphate, secondary nitrate, crustal, coal combustion power plant and harbour-industrial. Results showed that the application of constraints in PMF5.0 improved interpretability of profiles and comparability of estimated source contributions with stoichiometric calculations. The inter-comparison of PMF and CMB gave significant differences for secondary nitrate, biomass burning, and harbour-industrial sources, due to non-compatibility of these source profiles that have local specificities. When these site-dependent specificities were taken into account, optimising the input source profiles of CMB, a significant improvement in the comparison of the estimated source contributions with PMF was obtained.

Seasonal variations and source apportionment of complex polycyclic aromatic hydrocarbon mixtures in particulate matter in an electronic waste and urban area in South China.

PubMed

Chen, She-Jun; Wang, Jing; Wang, Tao; Wang, Ting; Mai, Bi-Xian; Simonich, Staci L Massey

2016-12-15

Complex polycyclic aromatic hydrocarbon (PAH) mixtures including parent PAHs, high molecular weight PAHs (MW 302 PAHs), and halogenated PAHs (HPAHs) were measured in particulate matter (PM) in an urban area and a rural electronic waste area in South China. The concentrations of MW < 302 PAHs at two sites were not significantly different with annual means of 23.2 ± 17.2 and 33.7 ± 29.0 ng/m 3 , respectively. However the concentrations of both MW 302 PAHs (5.35 ± 3.72 ng/m 3 ) and HPAH (49.9 pg/m 3 ) were significantly higher at the e-waste site than the urban site (2.81 ± 2.36 ng/m 3 and 28.2 ± 28.5 pg/m 3 ), suggesting e-waste recycling being a significant source of these PAHs. The majority of PAHs exhibited higher concentrations in winter and spring and lower concentrations in fall and summer. Meteorological conditions and increased emissions of PAHs in northern China due to domestic heating in colder seasons are important factors influencing the PAH seasonal variations. Source apportionment by the chemical mass balance (CMB) model indicated that residential stoves (coal combustion), industrial boilers (coal combustion), biomass burning, and vehicular emission accounted for 38 ± 14%, 30 ± 11%, 22 ± 22%, and 10 ± 7% of the PAHs in the urban PM, respectively. Comparable contributions from these sources were also observed for PM at the e-waste site. PAH emission factors are needed for primitive e-waste recycling to further understand the importance of this source to ambient air. Copyright © 2016 Elsevier B.V. All rights reserved.

Physically constrained source apportionment (PCSA) for polycyclic aromatic hydrocarbon using the Multilinear Engine 2-species ratios (ME2-SR) method.

PubMed

Liu, Gui-Rong; Shi, Guo-Liang; Tian, Ying-Ze; Wang, Yi-Nan; Zhang, Cai-Yan; Feng, Yin-Chang

2015-01-01

An improved physically constrained source apportionment (PCSA) technology using the Multilinear Engine 2-species ratios (ME2-SR) method was proposed and applied to quantify the sources of PM10- and PM2.5-associated polycyclic aromatic hydrocarbons (PAHs) from Chengdu in winter time. Sixteen priority PAH compounds were detected with mean ΣPAH concentrations (sum of 16 PAHs) ranging from 70.65 ng/m(3) to 209.58 ng/m(3) and from 59.17 ng/m(3) to 170.64 ng/m(3) for the PM10 and PM2.5 samples, respectively. The ME2-SR and positive matrix factorization (PMF) models were employed to estimate the source contributions of PAHs, and these estimates agreed with the experimental results. For the PMF model, the highest contributor to the ΣPAHs was vehicular emission (81.69% for PM10, 82.06% for PM2.5), followed by coal combustion (12.68%, 12.11%), wood combustion (5.65%, 4.45%) and oil combustion (0.72%, 0.88%). For the ME2-SR method, the highest contributions were from diesel (43.19% for PM10, 47.17% for PM2.5) and gasoline exhaust (34.94%, 32.44%), followed by wood combustion (8.79%, 6.37%), coal combustion (12.46%, 12.37%) and oil combustion (0.80%, 1.22%). However, the PAH ratios calculated for the factors extracted by ME2-SR were closer to the values from actual source profiles, implying that the results obtained from ME2-SR might be physically constrained and satisfactory. Copyright © 2014 Elsevier B.V. All rights reserved.

Source apportionment of wet-deposited atmospheric mercury in Tampa, Florida

NASA Astrophysics Data System (ADS)

Michael, Ryan; Stuart, Amy L.; Trotz, Maya A.; Akiwumi, Fenda

2016-03-01

In this paper, sources of mercury deposition to the Tampa area (Florida, USA) are investigated by analysis of one year (March 2000-March 2001) of daily wet deposition data. HYSPLIT back-trajectory modeling was performed to assess potential source locations for high versus low concentration events in data stratified by precipitation level. Positive matrix factorization (PMF) was also applied to apportion the elemental compositions from each event and to identify sources. Increased total mercury deposition was observed during summer months, corresponding to increased precipitation. However, mercury concentration in deposited samples was not strongly correlated with precipitation amount. Back-trajectories show air masses passing over Florida land in the short (12 h) and medium (24 h) term prior to deposition for high mercury concentration events. PMF results indicate that eleven factors contribute to the deposited elements in the event data. Diagnosed elemental profiles suggest the sources that contribute to mercury wet deposition at the study site are coal combustion (52% of the deposited mercury mass), municipal waste incineration (23%), medical waste incineration (19%), and crustal dust (6%). Overall, results suggest that sources local to the county and in Florida likely contributed substantially to mercury deposition at the study site, but distant sources may also contribute.

Characterization of atmospheric black carbon and co-pollutants in urban and rural areas of Spain

NASA Astrophysics Data System (ADS)

Becerril-Valle, M.; Coz, E.; Prévôt, A. S. H.; Močnik, G.; Pandis, S. N.; Sánchez de la Campa, A. M.; Alastuey, A.; Díaz, E.; Pérez, R. M.; Artíñano, B.

2017-11-01

A one-year black carbon (BC) experimental study was performed at three different locations (urban traffic, urban background, rural) in Spain with different equivalent BC (eBC) source characteristics by means of multi-wavelength Aethalometers. The Aethalometer model was used for the source apportionment study, based on the difference in absorption spectral dependence of emissions from biomass burning (bb) and fossil fuel (ff) combustion. Most studies use a single bb and ff absorption Ångström exponent (AAE) pair (AAEbb and AAEff), however in this work we use a range of AAE values associated with fossil fuel and biomass burning based on the available measurements, which represents more properly all conditions. A sensitivity analysis of the source specific AAE was carried out to determine the most appropriate AAE values, being site dependent and seasonally variable. Here we present a methodology for the determination of the ranges of AAEbb and AAEff by evaluating the correlations between the source apportionment of eBC using the Aethalometer model with four biomass burning tracers measured at the rural site. The best combination was AAEbb = [1.63-1.74] and AAEff = [0.97-1.12]. Mean eBC values (±SD) obtained during the period of study were 3.70 ± 3.73 μg m-3 at the traffic urban site, 2.33 ± 2.96 μg m-3 at the urban background location, and 2.61 ± 5.04 μg m-3 in the rural area. High contributions of eBC to the PM10 mass were found (values up to 21% in winter), but with high eBC/PM10 variability. The hourly mean eBCff and eBCbb concentrations varied from 0 to 51 μg m-3 and from 0 to 50 μg m-3 at the three sites, respectively, exhibiting distinct seasonal and daily patterns. The fossil fuel combustion was the dominant eBC source at the urban sites, while biomass burning dominated during the cold season (88% of eBCbb) in the rural area. Daily PM2.5 and PM10 samples were collected using high-volume air samplers and analyzed for OC and EC. Analysis of biomass burning tracers and organic (OC) and elemental (EC) carbon in the rural area indicate that biomass combustion is the main source, while OC and EC indicate a lower influence of this source at the urban site.

Overview of the Mathematical and Empirical Receptor Models Workshop (Quail Roost II)

NASA Astrophysics Data System (ADS)

Stevens, Robert K.; Pace, Thompson G.

On 14-17 March 1982, the U.S. Environmental Protection Agency sponsored the Mathematical and Empirical Receptor Models Workshop (Quail Roost II) at the Quail Roost Conference Center, Rougemont, NC. Thirty-five scientists were invited to participate. The objective of the workshop was to document and compare results of source apportionment analyses of simulated and real aerosol data sets. The simulated data set was developed by scientists from the National Bureau of Standards. It consisted of elemental mass data generated using a dispersion model that simulated transport of aerosols from a variety of sources to a receptor site. The real data set contained the mass, elemental, and ionic species concentrations of samples obtained in 18 consecutive 12-h sampling periods in Houston, TX. Some participants performed additional analyses of the Houston filters by X-ray powder diffraction, scanning electron microscopy, or light microscopy. Ten groups analyzed these data sets using a variety of modeling procedures. The results of the modeling exercises were evaluated and structured in a manner that permitted model intercomparisons. The major conclusions and recommendations derived from the intercomparisons were: (1) using aerosol elemental composition data, receptor models can resolve major emission sources, but additional analyses (including light microscopy and X-ray diffraction) significantly increase the number of sources that can be resolved; (2) simulated data sets that contain up to 6 dissimilar emission sources need to be generated, so that different receptor models can be adequately compared; (3) source apportionment methods need to be modified to incorporate a means of apportioning such aerosol species as sulfate and nitrate formed from SO 2 and NO, respectively, because current models tend to resolve particles into chemical species rather than to deduce their sources and (4) a source signature library may be required to be compiled for each airshed in order to improve the resolving capabilities of receptor models.

Chemical Composition and Source Apportionment of high temporal resolution PM1 data for January-August 2017 in Delhi, India

NASA Astrophysics Data System (ADS)

Bhandari, S.; Wang, D. S.; Gani, S.; Seraj, S.; Arub, Z.; Habib, G.; Apte, J.; Hildebrandt Ruiz, L.

2017-12-01

Exposure to fine particulate matter (PM) poses significant health risks, especially to residents in heavily populated areas. The current understanding of the sources and dynamics of PM pollution in developing countries like India is limited. Delhi, India is the second most populated city in the world that has extremely high winter PM concentrations and frequent severe pollution episodes. This study reports on composition measurements of submicron aerosol at 1 minute time resolution from January to August of 2017, collected at the Indian Institute of Technology Delhi using an Aerodyne Aerosol Chemical Speciation Monitor (ACSM) and black carbon (BC) measurements using an Aethalometer. Source apportionment was conducted on organic and inorganic mass spectra measured by the ACSM and black carbon data measured using Positive Matrix Factorization (PMF). High concentrations of particulate matter were observed with total PM1 at times exceeding 200 µg m-3 in winter. A significant drop in PM1 concentrations was observed in the winter-spring transition. As observed elsewhere, organic species dominated the submicron mass, contributing 60% of the total mass over the duration of the campaign. However, this fractional contribution varied substantially over the day: from 48% early in the morning to 73% late at night. Along with diurnal variation in total PM1 mass loadings, particulate chloride levels also exhibited a strong diurnal cycle, with concentrations as high as 50 µg m-3 observed in the early mornings of January 2017. Literature review on identification of winter chloride sources in Delhi points to local and regional sources such as biomass/open-waste burning and coal combustion. PMF receptor modeling identified several factors with distinct diurnal patterns. While hydrocarbon-like organic aerosol (HOA) factor has the largest mass fraction contribution, PMF results consistently suggest chloride presence as attributable to ammonium chloride. Interestingly, aerosol neutralization characterization shows an apparent acidity of aerosols. These results point to substantial differences in aerosol composition in Indian cities in comparison to cities around the world, especially with regards to the abundance of particulate chloride, and provide insights into the sources of PM1 measured in Delhi.

Chemical composition and source apportionment of PM10 at an urban background site in a high-altitude Latin American megacity (Bogota, Colombia).

PubMed

Ramírez, Omar; Sánchez de la Campa, A M; Amato, Fulvio; Catacolí, Ruth A; Rojas, Néstor Y; de la Rosa, Jesús

2018-02-01

Bogota registers frequent episodes of poor air quality from high PM 10 concentrations. It is one of the main Latin American megacities, located at 2600 m in the tropical Andes, but there is insufficient data on PM 10 source contribution. A characterization of the chemical composition and the source apportionment of PM 10 at an urban background site in Bogota was carried out in this study. Daily samples were collected from June 2015 to May 2016 (a total of 311 samples). Organic carbon (OC), elemental carbon (EC), water soluble compounds (SO 4 2- , Cl - , NO 3 - , NH 4 + ), major elements (Al, Fe, Mg, Ca, Na, K, P) and trace metals (V, Cd, Pb, Sr, Ba, among others) were analyzed. The results were interpreted in terms of their variability during the rainy season (RS) and the dry season (DS). The data obtained revealed that the carbonaceous fraction (∼51%) and mineral dust (23%) were the main PM 10 components, followed by others (15%), Secondary Inorganic Compounds (SIC) (11%) and sea salt (0.4%). The average concentrations of soil, SIC and OC were higher during RS than DS. However, peak values were observed during the DS due to photochemical activity and forest fires. Although trace metals represented <1% of PM 10 , high concentrations of toxic elements such as Pb and Sb on RS, and Cu on DS, were obtained. By using a PMF model, six factors were identified (∼96% PM 10 ) including fugitive dust, road dust, metal processing, secondary PM, vehicles exhaust and industrial emissions. Traffic (exhaust emissions + road dust) was the major PM 10 source, accounting for ∼50% of the PM 10 . The results provided novel data about PM 10 chemical composition, its sources and its seasonal variability during the year, which can help the local government to define control strategies for the main emission sources during the most critical periods. Copyright © 2017 Elsevier Ltd. All rights reserved.

APORT: a program for the area-based apportionment of county variables to cells of a polar grid. [Airborne pollutant transport models

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fields, D.E.; Little, C.A.

1978-11-01

The APORT computer code was developed to apportion variables tabulated for polygon-structured civil districts onto cells of a polar grid. The apportionment is based on fractional overlap between the polygon and the grid cells. Centering the origin of the polar system at a pollutant source site yields results that are very useful for assessing and interpreting the effects of airborne pollutant dissemination. The APOPLT graphics code, which uses the same data set as APORT, provides a convenient visual display of the polygon structure and the extent of the polar grid. The APORT/APOPLT methodology was verified by application to county summariesmore » of cattle population for counties surrounding the Oyster Creek, New Jersey, nuclear power plant. These numerical results, which were obtained using approximately 2-min computer time on an IBM System 360/91 computer, compare favorably to results of manual computations in both speed and accuracy.« less

Metals in Some Edible Fish and Shrimp Species Collected in Dry Season from Subarnarekha River, India.

PubMed

Giri, Soma; Singh, Abhay Kumar

2015-08-01

The concentration of As, Cd, Cu, Fe, Pb, Ni, Zn, Cr, Co and Sr were determined in five fish and one shrimp species collected from the Subarnarekha River during pre-monsoon season using inductively coupled plasma-mass spectrometry for a risk assessment and source apportionment study. Concentrations of metals in the fish and shrimp exceeded the recommended food standards for As, Cu, Ni, Cd and Zn in many samples. Principal component analysis suggested both innate and anthropogenic activities as contributing sources of metal in the fish and shrimp. The calculated target hazard quotients and hazard indices indicated that high concentrations of metals in some species at some locations present an appreciable risk to the health of consumers of these species.

Elemental quantification, chemistry, and source apportionment in golf course facilities in a semi-arid urban landscape using a portable X-ray fluorescence spectrometer

NASA Astrophysics Data System (ADS)

Udeigwe, T. K.; Young, J.; Kandakji, T.; Weindorf, D. C.; Mahmoud, M. A.; Stietiya, M. H.

2015-04-01

This study extends the application of the portable X-ray fluorescence (PXRF) spectrometry to the examination of elements in semi-arid urban landscapes of the Southern High Plains (SHP) of the United States, focusing on golf courses. The complex environmental challenges of this region and the unique management practices at golf course facilities could lead to differences in concentration and in the chemistry of elements between managed (irrigated) and non-managed (non-irrigated) portions of these facilities. Soil samples were collected at depths of 0-10, 10-20, and 20-30 cm from managed and non-managed areas of seven different facilities in the city of Lubbock, Texas, and analyzed for a suite of soil properties. Total elemental quantification was conducted using a PXRF spectrometer. Findings mostly indicated no significant differences in the concentration of examined elements between the managed and non-managed areas of the facilities. However, strong positive relationships (R = 0.82-0.91, p < 0.001) were observed among elements (e.g., Fe on the one hand and Cr, Mn, Ni, and As on the other; Cu and Zn; As and Cr) and between these elements and soil constituents or properties such as clay, calcium carbonate, organic matter, and pH. The strengths of these relationships were mostly higher in the non-managed areas, suggesting a possible alteration in the chemistry of these elements by anthropogenic influences in the managed areas. Principal component and correlation analyses within the managed areas suggested that As, Cr, Fe, Mn, and Ni could be of lithogenic origin, while Cu, Pb, and Zn could have anthropogenic influences. Only one possible, likely lithogenic, source of the elements was identified within the non-managed areas. As evidenced by the study, the PXRF spectrometer can be a valuable tool for elemental quantification and rapid investigation of elemental interaction and source apportionment in semi-arid climates.

Elemental quantification, chemistry, and source apportionment in golf course facilities in semi-arid urban landscape using portable x-ray fluorescence spectrometer

NASA Astrophysics Data System (ADS)

Udeigwe, T. K.; Young, J.; Kandakji, T.; Weindorf, D. C.; Mahmoud, M. A.; Stietiya, M. H.

2015-01-01

This study extends the application of the portable x-ray fluorescence (PXRF) spectrometry to examination of elements in semi-arid urban landscapes of the Southern High Plains (SHP) of the United States (US), focusing on golf courses. The complex environmental challenges of this region and the unique management practices at golf course facilities could lead to differences in concentration and chemistry of elements between managed (irrigated) and non-managed (non-irrigated) portions of these facilities. Soil samples were collected at the depths of 0-10, 10-20, and 20-30 cm from managed and non-managed areas of seven different facilities in the city of Lubbock, Texas, and analyzed for a suite of soil properties. Total elemental quantification was conducted using PXRF. Findings mostly indicated no significant differences in concentration of examined elements between the managed and non-managed areas of the facilities. However, strong positive relationships (R2 = 0.82-0.91, p < 0.001) were observed among elements (e.g. Fe and each of Cr, Mn, Ni, and As; Cu and Zn; As and Cr) and between these elements and soil constituents or properties such as clay, calcium carbonate, organic matter, and pH. The strengths of these relationships were mostly higher in the non-managed areas, suggesting possible alteration in the chemistry of these elements by anthropogenic influences. Principal component analyses (PCA) and correlation analyses within the managed areas suggested that As, Cr, Fe, Mn, and Ni could be of lithogenic origin, while Cu, Pb, and Zn were attributed to anthropogenic influences. Only one possible source of element, likely lithogenic, was identified within non-managed areas. As evidenced from the study, the PXRF can be a valuable tool for elemental quantification, and rapid investigation of elemental interaction and source apportionment in semi-arid climates.

Integrated Application of Multivariate Statistical Methods to Source Apportionment of Watercourses in the Liao River Basin, Northeast China

PubMed Central

Chen, Jiabo; Li, Fayun; Fan, Zhiping; Wang, Yanjie

2016-01-01

Source apportionment of river water pollution is critical in water resource management and aquatic conservation. Comprehensive application of various GIS-based multivariate statistical methods was performed to analyze datasets (2009–2011) on water quality in the Liao River system (China). Cluster analysis (CA) classified the 12 months of the year into three groups (May–October, February–April and November–January) and the 66 sampling sites into three groups (groups A, B and C) based on similarities in water quality characteristics. Discriminant analysis (DA) determined that temperature, dissolved oxygen (DO), pH, chemical oxygen demand (CODMn), 5-day biochemical oxygen demand (BOD5), NH4+–N, total phosphorus (TP) and volatile phenols were significant variables affecting temporal variations, with 81.2% correct assignments. Principal component analysis (PCA) and positive matrix factorization (PMF) identified eight potential pollution factors for each part of the data structure, explaining more than 61% of the total variance. Oxygen-consuming organics from cropland and woodland runoff were the main latent pollution factor for group A. For group B, the main pollutants were oxygen-consuming organics, oil, nutrients and fecal matter. For group C, the evaluated pollutants primarily included oxygen-consuming organics, oil and toxic organics. PMID:27775679

Measurements and source apportionment of particle-associated polycyclic aromatic hydrocarbons in ambient air in Riyadh, Saudi Arabia

NASA Astrophysics Data System (ADS)

Bian, Qijing; Alharbi, Badr; Collett, Jeffrey; Kreidenweis, Sonia; Pasha, Mohammad J.

2016-07-01

Ambient air samples were obtained in Riyadh, the capital and largest city of Saudi Arabia, during two measurement campaigns spanning September 2011 to September 2012. Sixteen particle-phase polycyclic aromatic hydrocarbons (PAH) were quantified in 167 samples. Pyrene and fluoranthene were the most abundant PAH, with average of 3.37 ± 14.01 ng m-3 and 8.00 ± 44.09 ng m-3, respectively. A dominant contribution from low molecular weight (LMW) PAH (MW < 228) suggested a large influence of industrial emissions on PAH concentrations. Monte Carlo source apportionment using diagnostic ratios showed that 80 ± 10% of the average LMW PAH concentrations were contributed by petroleum vapor emissions, while 53 ± 19% of high molecular weight (HMW) PAH were from solid fuel combustion emissions. The positive matrix factorization model estimated that oil combustion emissions dominated total PAH concentrations, accounting for on average 96%, likely due to widespread use of oil fuels in energy production (power plants and industries). Our results demonstrate the significant influence of petroleum product production and consumption on particulate-phase PAH concentrations in Riyadh, but also point to the importance of traffic and solid fuel burning, including coke burning and seasonal biomass burning, especially as they contribute to the ambient levels of HMW PAH.

Source apportionment of speciated PM2.5 and non-parametric regressions of PM2.5 and PM(coarse) mass concentrations from Denver and Greeley, Colorado, and construction and evaluation of dichotomous filter samplers

NASA Astrophysics Data System (ADS)

Piedrahita, Ricardo A.

The Denver Aerosol Sources and Health study (DASH) was a long-term study of the relationship between the variability in fine particulate mass and chemical constituents (PM2.5, particulate matter less than 2.5mum) and adverse health effects such as cardio-respiratory illnesses and mortality. Daily filter samples were chemically analyzed for multiple species. We present findings based on 2.8 years of DASH data, from 2003 to 2005. Multilinear Engine 2 (ME-2), a receptor-based source apportionment model was applied to the data to estimate source contributions to PM2.5 mass concentrations. This study relied on two different ME-2 models: (1) a 2-way model that closely reflects PMF-2; and (2) an enhanced model with meteorological data that used additional temporal and meteorological factors. The Coarse Rural Urban Sources and Health study (CRUSH) is a long-term study of the relationship between the variability in coarse particulate mass (PMcoarse, particulate matter between 2.5 and 10mum) and adverse health effects such as cardio-respiratory illnesses, pre-term births, and mortality. Hourly mass concentrations of PMcoarse and fine particulate matter (PM2.5) are measured using tapered element oscillating microbalances (TEOMs) with Filter Dynamics Measurement Systems (FDMS), at two rural and two urban sites. We present findings based on nine months of mass concentration data, including temporal trends, and non-parametric regressions (NPR) results, which were used to characterize the wind speed and wind direction relationships that might point to sources. As part of CRUSH, 1-year coarse and fine mode particulate matter filter sampling network, will allow us to characterize the chemical composition of the particulate matter collected and perform spatial comparisons. This work describes the construction and validation testing of four dichotomous filter samplers for this purpose. The use of dichotomous splitters with an approximate 2.5mum cut point, coupled with a 10mum cut diameter inlet head allows us to collect the separated size fractions that the collocated TEOMs collect continuously. Chemical analysis of the filters will include inorganic ions, organic compounds, EC, OC, and biological analyses. Side by side testing showed the cut diameters were in agreement with each other, and with a well characterized virtual impactor lent to the group by the University of Southern California. Error propagation was performed and uncertainty results were similar to the observed standard deviations.

Source apportionment of elevated wintertime PAHs by compound-specific radiocarbon analysis

NASA Astrophysics Data System (ADS)

Sheesley, R. J.; Kruså, M.; Krecl, P.; Johansson, C.; Gustafsson, Ã.-.

2009-05-01

Natural abundance radiocarbon analysis facilitates distinct source apportionment between contemporary biomass/biofuel (14C "alive") versus fossil fuel (14C "dead") combustion. Here, the first compound-specific radiocarbon analysis (CSRA) of atmospheric polycyclic aromatic hydrocarbons (PAHs) was demonstrated for a set of samples collected in Lycksele, Sweden a small town with frequent episodes of severe atmospheric pollution in the winter. Renewed interest in using residential wood combustion (RWC) means that this type of seasonal pollution is of increasing concern in many areas. Five individual/paired PAH isolates from three pooled fortnight-long filter collections were analyzed by CSRA: phenanthrene, fluoranthene, pyrene, benzo[b+k]fluoranthene and indeno[cd]pyrene plus benzo[ghi]perylene; phenanthrene was the only compound also analyzed in the gas phase. The measured Δ14C for PAHs spanned from -138.3‰ to 58.0‰. A simple isotopic mass balance model was applied to estimate the fraction biomass (fbiomass) contribution, which was constrained to 71-87% for the individual PAHs. Indeno[cd]pyrene plus benzo[ghi]perylene had an fbiomass of 71%, while fluoranthene and phenanthrene (gas phase) had the highest biomass contribution at 87%. The total organic carbon (TOC, defined as carbon remaining after removal of inorganic carbon) fbiomass was estimated to be 77%, which falls within the range for PAHs. This CSRA data of atmospheric PAHs established that RWC is the dominating source of atmospheric PAHs to this region of the boreal zone with some variations among RWC contributions to specific PAHs.

Source apportionment of major and trace elements in aerosols during smog episodes in large cities in China

NASA Astrophysics Data System (ADS)

Furger, Markus; Rai, Pragati; Visser, Suzanne; Elser, Miriam; Canonaco, Francesco; Slowik, Jay G.; Huang, Ru-Jin; Prévôt, André S. H.; Baltensperger, Urs

2017-04-01

Air pollution in Chinese cities is one of the environmental problems China has to address to mitigate the impacts on human health, air quality and climate. Average concentrations of particulate matter exceed 100 μg m-3 in many places in China, and the government is developing and implementing strategies to reduce the load of pollutants by various measures. A characterization of airborne particulate matter (PM), especially its composition and sources, will help in optimizing reduction and mitigation strategies for air pollution. We collected PM10 aerosols with a rotating drum impactor (RDI) in Xi'an in December 2013 and in Beijing in January 2014 with 30-min time resolution and for three size ranges (cut-off sizes 10, 2.5 and 1 μm). Each campaign encompassed one or more high pollution episodes in the respective city. Elements from Na to Pb were analyzed with synchrotron radiation induced X-ray fluorescence spectrometry (SR-XRF), and the resulting time series were used for source apportionment performed with the Multilinear-Engine 2 (ME-2) implementation of the Positive Matrix Factorization algorithm. The preliminary computations yielded 5 factors for Beijing, namely road dust, sea salt, traffic-related, industrial, coal combustion. For Xi'an an additional desert dust factor was found. Further refinement could be expected from including the smaller size fractions, e.g. a sulfur-rich factor for secondary sulfate or a reacted chlorine factor in the fine mode fraction.

Modelling winter organic aerosol at the European scale with CAMx: evaluation and source apportionment with a VBS parameterization based on novel wood burning smog chamber experiments

NASA Astrophysics Data System (ADS)

Ciarelli, Giancarlo; Aksoyoglu, Sebnem; El Haddad, Imad; Bruns, Emily A.; Crippa, Monica; Poulain, Laurent; Äijälä, Mikko; Carbone, Samara; Freney, Evelyn; O'Dowd, Colin; Baltensperger, Urs; Prévôt, André S. H.

2017-06-01

We evaluated a modified VBS (volatility basis set) scheme to treat biomass-burning-like organic aerosol (BBOA) implemented in CAMx (Comprehensive Air Quality Model with extensions). The updated scheme was parameterized with novel wood combustion smog chamber experiments using a hybrid VBS framework which accounts for a mixture of wood burning organic aerosol precursors and their further functionalization and fragmentation in the atmosphere. The new scheme was evaluated for one of the winter EMEP intensive campaigns (February-March 2009) against aerosol mass spectrometer (AMS) measurements performed at 11 sites in Europe. We found a considerable improvement for the modelled organic aerosol (OA) mass compared to our previous model application with the mean fractional bias (MFB) reduced from -61 to -29 %. We performed model-based source apportionment studies and compared results against positive matrix factorization (PMF) analysis performed on OA AMS data. Both model and observations suggest that OA was mainly of secondary origin at almost all sites. Modelled secondary organic aerosol (SOA) contributions to total OA varied from 32 to 88 % (with an average contribution of 62 %) and absolute concentrations were generally under-predicted. Modelled primary hydrocarbon-like organic aerosol (HOA) and primary biomass-burning-like aerosol (BBPOA) fractions contributed to a lesser extent (HOA from 3 to 30 %, and BBPOA from 1 to 39 %) with average contributions of 13 and 25 %, respectively. Modelled BBPOA fractions were found to represent 12 to 64 % of the total residential-heating-related OA, with increasing contributions at stations located in the northern part of the domain. Source apportionment studies were performed to assess the contribution of residential and non-residential combustion precursors to the total SOA. Non-residential combustion and road transportation sector contributed about 30-40 % to SOA formation (with increasing contributions at urban and near industrialized sites), whereas residential combustion (mainly related to wood burning) contributed to a larger extent, around 60-70 %. Contributions to OA from residential combustion precursors in different volatility ranges were also assessed: our results indicate that residential combustion gas-phase precursors in the semivolatile range (SVOC) contributed from 6 to 30 %, with higher contributions predicted at stations located in the southern part of the domain. On the other hand, the oxidation products of higher-volatility precursors (the sum of intermediate-volatility compounds (IVOCs) and volatile organic compounds (VOCs)) contribute from 15 to 38 % with no specific gradient among the stations. Although the new parameterization leads to a better agreement between model results and observations, it still under-predicts the SOA fraction, suggesting that uncertainties in the new scheme and other sources and/or formation mechanisms remain to be elucidated. Moreover, a more detailed characterization of the semivolatile components of the emissions is needed.

Organic composition and source apportionment of fine aerosol at Monterrey, Mexico, based on organic markers

NASA Astrophysics Data System (ADS)

Mancilla, Y.; Mendoza, A.; Fraser, M. P.; Herckes, P.

2016-01-01

Primary emissions from anthropogenic and biogenic sources as well as secondary formation are responsible for the pollution levels of ambient air in major urban areas. These sources release fine particles into the air that negatively impact human health and the environment. Organic molecular markers, which are compounds that are unique to specific PM2.5 sources, can be utilized to identify the major emission sources in urban areas. In this study, 43 representative PM2.5 samples, for both daytime and nighttime periods, were built from individual samples collected in an urban site of the Monterrey metropolitan area (MMA) during the spring and fall of 2011 and 2012. The samples were analyzed for organic carbon, elemental carbon, and organic molecular markers. Several diagnostic tools were employed for the preliminary identification of emission sources. Organic compounds for eight compound classes were quantified. The n-alkanoic acids were the most abundant, followed by n-alkanes, wood smoke markers, and levoglucosan/alkenoic acids. Polycyclic aromatic hydrocarbons (PAHs) and hopanes were less abundant. The carbon preference index (0.7-2.6) for n-alkanes indicates a major contribution of anthropogenic and mixed sources during the fall and the spring, respectively. Hopanes levels confirmed the contribution from gasoline and diesel engines. In addition, the contribution of gasoline and diesel vehicle exhaust was confirmed and identified by the PAH concentrations in PM2.5. Diagnostic ratios of PAHs showed emissions from burning coal, wood, biomass, and other fossil fuels. The total PAHs and elemental carbon were correlated (r2 = 0.39-0.70) across the monitoring periods, reinforcing that motor vehicles are the major contributors of PAHs. Cholesterol levels remained constant during the spring and fall, showing evidence of the contribution of meat-cooking operations, while the isolated concentrations of levoglucosan suggested occasional biomass burning events. Finally, source attribution results obtained using the CMB (chemical mass balance) model indicate that emissions from motor vehicle exhausts are the most important, accounting for the 64 % of the PM2.5, followed by meat-cooking operations with 31 % The vegetative detritus and biomass burning had the smallest contribution (2.2 % of the PM2.5). To our knowledge, this is only the second study to explore the organic composition and source apportionment of fine organic aerosol based on molecular markers in Mexico and the first for the MMA. Particularly molecular marker were quantified by solvent extraction with dichloromethane, derivatization, and gas chromatography with mass spectrometry (GC/MS).

[Analysis on Mechanism of Rainout Carried by Wet Stack of Thermal Power Plant].

PubMed

Ouyang, Li-hua; Zhuang, Ye; Liu, Ke-wei; Chen, Zhen-yu; Gu, Peng

2015-06-01

Rainout from wet-stack took placed in many thermal power plants with WFGD system. Research on causes of the rainout is important to solve the problem. The objective of this research is to analyze the mechanism of rainout. Field study was performed to collect experimental data in one thermal power plant, including the amount of desulfurization slurry carried by wet flue gas, liquor condensate from wet duct, and droplets from the wet stack. Source apportionment analysis was carried out based on physical and chemical data of liquid sample and solid sample. The result showed that mist eliminator operated well, which met the performance guarantee value. But the total amount of desulfurization slurry in flue gas and the sulfate concentration in liquid condensate discharge from the wet duct/stack increased. The liquid condensate accumulated in the wet duct/stack led to liquid re-entrainment. In conclusion, the rainout in this power plant was caused by the short of wet ductwork or liquid discharge system, the droplets caused by re-entrainment carried by the saturated gas released from the stack. The main undissolved components of the rainout were composite carbonate and aluminosilicate. Although ash concentration in this WFGD met the regulation criteria, source apportionment analysis showed that fly ash contributed to rainout was accounted for 60%. This percentage value was same as the data of solid particles in the condensate. It is important to optimize the wet ductwork, wet stack liner, liquid collectors and drainage. Avoiding the accumulation from saturated vapor thermal condensation is an effective way to solve the wet stack rainout.

Diagnosis of aged prescribed burning plumes impacting an urban area.

PubMed

Lee, Sangil; Kim, Hyeon K; Yan, Bo; Cobb, Charles E; Hennigan, Chris; Nichols, Sara; Chamber, Michael; Edgerton, Eric S; Jansen, John J; Hu, Yongtao; Zheng, Mei; Weber, Rodney J; Russell, Armistead G

2008-03-01

An unanticipated wind shift led to the advection of plumes from two prescribed burning sites that impacted Atlanta, GA, producing a heavy smoke event late in the afternoon on February 28, 2007. Observed PM2.5 concentrations increased to over 140 microg/m3 and O3 concentrations up to 30 ppb in a couple of hours, despite the late hour in February when photochemistry is less vigorous. A detailed investigation of PM2.5 chemical composition and source apportionment analysis showed that the increase in PM2.5 mass was driven mainly by organic carbon (OC). However, both results from source apportionment and an observed nonlinear relationship between OC and PM2.5 potassium (K) indicate that the increased OC was not due solely to primary emissions. Most of the OC was water-soluble organic carbon (WSOC) and was dominated by hydrophobic compounds. The data are consistent with large enhancements in isoprenoid (isoprene and monoterpenes) and other volatile organic compounds emitted from prescribed burning that led to both significant O3 and secondary organic aerosol (SOA) production. Formation of oligomers from oxidation products of isoprenoid compounds or condensation of volatile organic compounds (VOCs) with multiple functional groups emitted during prescribed burning appears to be a major component of the secondary organic contributor of the SOA. The results from this study imply that enhanced emissions due to the fire itself and elevated temperature in the burning region should be considered in air quality models (e.g., receptor and emission-based models) to assess impacts of prescribed burning emissions on ambient air quality.

Spatial and temporal variations of aerosols around Beijing in summer 2006: Model evaluation and source apportionment

NASA Astrophysics Data System (ADS)

Matsui, H.; Koike, M.; Kondo, Y.; Takegawa, N.; Kita, K.; Miyazaki, Y.; Hu, M.; Chang, S.; Blake, D. R.; Fast, J. D.; Zaveri, R. A.; Streets, D. G.; Zhang, Q.; Zhu, T.

2009-12-01

Regional aerosol model calculations were made using the WRF-CMAQ and WRF-chem models to study spatial and temporal variations of aerosols around Beijing, China, in the summer of 2006, when the CAREBEIJING-2006 intensive campaign was conducted. Model calculations captured temporal variations of primary (such as elemental carbon, EC) and secondary (such as sulfate) aerosols observed in and around Beijing. The spatial distributions of aerosol optical depth observed by the MODIS satellite sensors were also reproduced over northeast China. Model calculations showed distinct differences in spatial distributions between primary and secondary aerosols in association with synoptic-scale meteorology. Secondary aerosols increased in air around Beijing on a scale of about 1000 x 1000 km2 under an anticyclonic pressure system. This airmass was transported northward from the high anthropogenic emission area extending south of Beijing with continuous photochemical production. Subsequent cold front passage brought clean air from the north, and polluted air around Beijing was swept to the south of Beijing. This cycle was repeated about once a week and was found to be responsible for observed enhancements/reductions of aerosols at the intensive measurement sites. In contrast to secondary aerosols, the spatial distributions of primary aerosols (EC) reflected those of emissions, resulting in only slight variability despite the changes in synoptic-scale meteorology. In accordance with these results, source apportionment simulations revealed that primary aerosols around Beijing were controlled by emissions within 100 km around Beijing within the preceding 24 hours, while emissions as far as 500 km and within the preceding 3 days were found to affect secondary aerosols.

Source contribution of PM₂.₅ at different locations on the Malaysian Peninsula.

PubMed

Ee-Ling, Ooi; Mustaffa, Nur Ili Hamizah; Amil, Norhaniza; Khan, Md Firoz; Latif, Mohd Talib

2015-04-01

This study determined the source contribution of PM2.5 (particulate matter <2.5 μm) in air at three locations on the Malaysian Peninsula. PM2.5 samples were collected using a high volume sampler equipped with quartz filters. Ion chromatography was used to determine the ionic composition of the samples and inductively coupled plasma mass spectrometry was used to determine the concentrations of heavy metals. Principal component analysis with multilinear regressions were used to identify the possible sources of PM2.5. The range of PM2.5 was between 10 ± 3 and 30 ± 7 µg m(-3). Sulfate (SO4 (2-)) was the major ionic compound detected and zinc was found to dominate the heavy metals. Source apportionment analysis revealed that motor vehicle and soil dust dominated the composition of PM2.5 in the urban area. Domestic waste combustion dominated in the suburban area, while biomass burning dominated in the rural area.

Assessment of Contribution of Contemporary Carbon Sources to Size-Fractionated Particulate Matter and Time-Resolved Bulk Particulate Matter Using the Measurement of Radiocarbon

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hwang, H M; Young, T M; Buchholz, B A

2009-04-16

This study was motivated by a desire to improve understanding of the sources contributing to the carbon that is an important component of airborne particulate matter (PM). The ultimate goal of this project was to lay a ground work for future tools that might be easily implemented with archived or routinely collected samples. A key feature of this study was application of radiocarbon measurement that can be interpreted to indicate the relative contributions from fossil and non-fossil carbon sources of atmospheric PM. Size-resolved PM and time-resolved PM{sub 10} collected from a site in Sacramento, CA in November 2007 (Phase I)more » and March 2008 (Phase II) were analyzed for radiocarbon and source markers such as levoglucosan, cholesterol, and elemental carbon. Radiocarbon data indicates that the contributions of non-fossil carbon sources were much greater than that from fossil carbon sources in all samples. Radiocarbon and source marker measurements confirm that a greater contribution of non-fossil carbon sources in Phase I samples was highly likely due to residential wood combustion. The present study proves that measurement of radiocarbon and source markers can be readily applied to archived or routinely collected samples for better characterization of PM sources. More accurate source apportionment will support ARB in developing more efficient control strategies.« less

Heavy metal transport in large river systems: heavy metal emissions and loads in the Rhine and Elbe river basins

NASA Astrophysics Data System (ADS)

Vink, Rona; Behrendt, Horst

2002-11-01

Pollutant transport and management in the Rhine and Elbe basins is still of international concern, since certain target levels set by the international committees for protection of both rivers have not been reached. The analysis of the chain of emissions of point and diffuse sources to river loads will provide policy makers with a tool for effective management of river basins. The analysis of large river basins such as the Elbe and Rhine requires information on the spatial and temporal characteristics of both emissions and physical information of the entire river basin. In this paper, an analysis has been made of heavy metal emissions from various point and diffuse sources in the Rhine and Elbe drainage areas. Different point and diffuse pathways are considered in the model, such as inputs from industry, wastewater treatment plants, urban areas, erosion, groundwater, atmospheric deposition, tile drainage, and runoff. In most cases the measured heavy metal loads at monitoring stations are lower than the sum of the heavy metal emissions. This behaviour in large river systems can largely be explained by retention processes (e.g. sedimentation) and is dependent on the specific runoff of a catchment. Independent of the method used to estimate emissions, the source apportionment analysis of observed loads was used to determine the share of point and diffuse sources in the heavy metal load at a monitoring station by establishing a discharge dependency. The results from both the emission analysis and the source apportionment analysis of observed loads were compared and gave similar results. Between 51% (for Hg) and 74% (for Pb) of the total transport in the Elbe basin is supplied by inputs from diffuse sources. In the Rhine basin diffuse source inputs dominate the total transport and deliver more than 70% of the total transport. The diffuse hydrological pathways with the highest share are erosion and urban areas.

Urban particulate matter pollution: a tale of five cities.

PubMed

Pandis, Spyros N; Skyllakou, Ksakousti; Florou, Kalliopi; Kostenidou, Evangelia; Kaltsonoudis, Christos; Hasa, Erion; Presto, Albert A

2016-07-18

Five case studies (Athens and Paris in Europe, Pittsburgh and Los Angeles in the United States, and Mexico City in Central America) are used to gain insights into the changing levels, sources, and role of atmospheric chemical processes in air quality in large urban areas as they develop technologically. Fine particulate matter is the focus of our analysis. In all cases reductions of emissions by industrial and transportation sources have resulted in significant improvements in air quality during the last few decades. However, these changes have resulted in the increasing importance of secondary particulate matter (PM) which dominates over primary in most cases. At the same time, long range transport of secondary PM from sources located hundreds of kilometres from the cities is becoming a bigger contributor to the urban PM levels in all seasons. "Non-traditional" sources including cooking, and residential and agricultural biomass burning contribute an increasing fraction of the now reduced fine PM levels. Atmospheric chemistry is found to change the chemical signatures of a number of these sources relatively fast both during the day and night, complicating the corresponding source apportionment.

Spatial and temporal variability of fine particle composition and source types in five cities of Connecticut and Massachusetts

PubMed Central

Lee, Hyung Joo; Gent, Janneane F.; Leaderer, Brian P.; Koutrakis, Petros

2011-01-01

To protect public health from PM2.5 air pollution, it is critical to identify the source types of PM2.5 mass and chemical components associated with higher risks of adverse health outcomes. Source apportionment modeling using Positive Matrix Factorization (PMF), was used to identify PM2.5 source types and quantify the source contributions to PM2.5 in five cities of Connecticut and Massachusetts. Spatial and temporal variability of PM2.5 mass, components and source contributions were investigated. PMF analysis identified five source types: regional pollution as traced by sulfur, motor vehicle, road dust, oil combustion and sea salt. The sulfur-related regional pollution and traffic source type were major contributors to PM2.5. Due to sparse ground-level PM2.5 monitoring sites, current epidemiological studies are susceptible to exposure measurement errors. The higher correlations in concentrations and source contributions between different locations suggest less spatial variability, resulting in less exposure measurement errors. When concentrations and/or contributions were compared to regional averages, correlations were generally higher than between-site correlations. This suggests that for assigning exposures for health effects studies, using regional average concentrations or contributions from several PM2.5 monitors is more reliable than using data from the nearest central monitor. PMID:21429560

Receptor model comparisons and wind direction analyses of volatile organic compounds and submicrometer particles in an arid, binational, urban air shed.

PubMed

Mukerjee, Shaibal; Norris, Gary A; Smith, Luther A; Noble, Christopher A; Neas, Lucas M; Ozkaynak, A Halûk; Gonzales, Melissa

2004-04-15

The relationship between continuous measurements of volatile organic compounds sources and particle number was evaluated at a Photochemical Assessment Monitoring Station Network (PAMS) site located near the U.S.-Mexico Border in central El Paso, TX. Sources of volatile organic compounds (VOCs) were investigated using the multivariate receptor model UNMIX and the effective variance least squares receptor model known as Chemical Mass Balance (CMB, Version 8.0). As expected from PAMS measurements, overall findings from data screening as well as both receptor models confirmed that mobile sources were the major source of VOCs. Comparison of hourly source contribution estimates (SCEs) from the two receptor models revealed significant differences in motor vehicle exhaust and evaporative gasoline contributions. However, the motor vehicle exhaust contributions were highly correlated with each other. Motor vehicle exhaust was also correlated with the ultrafine and accumulation mode particle count, which suggests that motor vehicle exhaust is a source of these particles at the measurement site. Wind sector analyses were performed using the SCE and pollutant data to assess source location of VOCs, particle count, and criteria pollutants. Results from this study have application to source apportionment studies and mobile source emission control strategies that are ongoing in this air shed.

Source Apportionment Analysis of Measured Fine Particulate Matter in a Semi-Arid Urban Airshed in Corpus Christi, U.S.A

NASA Astrophysics Data System (ADS)

Karnae, Saritha; John, Kuruvilla

2010-05-01

Corpus Christi is an industrialized urban area of South Texas that is currently in compliance with the National Ambient Air Quality Standards (NAAQS) for PM2.5 as set by the United States Environmental Protection Agency (U.S EPA). However a gradual increase in the annual and 24-hour PM2.5 concentrations was noted since 2001. In this study, principal component analysis/absolute principal component scores (PCA/APCS) was used as a source apportionment technique to identify key source categories that affected the measured PM2.5 concentrations at a continuous ambient monitoring station (CAMS) 04 maintained and operated by Texas Commission on Environmental Quality (TCEQ) during 2000 through 2007. Cluster analysis using computed backward trajectories was performed on days with high PM2.5 concentrations. The elevated PM days were heavily influenced by transported levels of PM during three types of episodic events including smoke plumes due to biomass burning in Mexico and Central America during April and May, sub-Saharan dust transport from Africa during June and July, and regional haze transport from highly industrialized areas of Texas and surrounding Midwestern states during September. Pyrotechnic emissions during local firework events during the New Year day celebrations under stagnant meteorological conditions also resulted in elevated PM2.5 concentrations. PCA/APCS identified five key source categories that accounted for 78% of the variance in the PM2.5 concentrations measured within the urban airshed. Secondary sulphates were identified to be the major contributor accounting for 46% of the apportioned mass. This was followed by mobile sources which accounted for 26%. The other sources that were identified by PCA/APCS included crustal dust, a commingled source of biomass burning and sea salt, and secondary nitrates. Increase in secondary sulphates was observed during August and September typically associated with the long range transport of continental haze from industrialized areas in Texas and surrounding states. Mobile source contributions increased during the winter months due to an increase in tourism related activities in the area. Biomass burning in Mexico and Central America during April and May contributed to elevated PM2.5 concentrations observed in the Corpus Christi urban airshed.

Air Mobility and the Development of Attack Aviation During the Vietnam War from 1965-1967

DTIC Science & Technology

2014-06-13

frame covered with thin sheet metal was vulnerable to small arms and heavy machine gun fire. The most vulnerable time was during the low-level...reviewing instructions, searching existing data sources , gathering and maintaining the data needed, and completing and reviewing this collection of...of on- call aircraft necessary for tactical support. The Air Force had additional missions that received higher apportionment based on strategic and

Radiocarbon-based Source Apportionment of Organic, Elemental and Water-soluble Organic Carbon Aerosols and the Light Absorption of Water-soluble Organic Carbon Aerosols in the East Asia High-intensity Winter Campaigns in 2014

NASA Astrophysics Data System (ADS)

Fang, W.; Andersson, A.; Zheng, M.; Lee, M.; Kim, S. W.; Du, K.; Gustafsson, O.

2016-12-01

Improved understanding of anthropogenic aerosol effects on atmospheric chemistry and climate as well as efficient mitigation actions are hampered by the limited comprehension of the relative contributions of different sources of carbonaceous aerosols and of their subsequent atmospheric processing. Here, we present dual carbon isotope constrained source apportionment and optical properties of carbonaceous aerosols simultaneously both at urban and rural receptor sites, includes North China Plain (NCP, Beijing and Tianjin), Yangtze River Delta (YRD, Shanghai, Zhejiang), and Jeju Island (Korea Climate Observatory at Gosan) during January 2014 field campaigns. The radiocarbon (Δ14C) data show that fossil combustions contribute equally ˜80 ± 5% to elemental carbon (EC) aerosol in Beijing, Tianjin, and Shanghai, and 66 ± 9% to Gosan-EC aerosol, while the specific sources of the dominant fossil fuel component were dramatically different among these sites. The mean fraction coal combustion of Beijing-EC, Tianjin-EC, and Gosan-EC is double that of Shanghai-EC. The other large fraction (72―92%) of carbonaceous aerosol is organic carbon (OC) aerosol which contains water soluble and water insoluble organic carbon (WSOC and WISOC). OC, WISOC, and WSOC in Beijing and Gosan sites were still observed largely from fossil sources (53―75%). The more 13C-enriched signature of Gosan-WSOC (-22.8 ± 0.2‰) compared to Gosan-EC (-23.9 ± 0.4‰) and Beijing-WSOC (-23.5 ± 0.7‰) reflects that WSOC is likely more affected by atmospheric aging during long-rang transport than is EC. The high light absorption coefficients of PM2.5, PM1, and TSP were observed at Gosan during this study and was frequently reaching 20―60 Mm-1 by aethalometer and continuous light absorption photometer. The mass absorption cross section of WSOC (MAC365) for above sites is high (1.5 ± 0.8 m2/g), accounted for ˜14 ± 5% of the total direct absorbance relative to EC, which is significantly higher than the previous findings in S. Asia, N. America, and Europe.

Sources of methane and nitrous oxide in California's Central Valley estimated through direct airborne flux and positive matrix factorization source apportionment of groundbased and regional tall tower measurements

NASA Astrophysics Data System (ADS)

Guha, Abhinav

Methane (CH4) and nitrous oxide (N2O) are two major greenhouse gases that contribute significantly to the increase in anthropogenic radiative-forcing causing perturbations to the earth's climate system. In a watershed moment in the state's history of environmental leadership and commitment, California, in 2006, opted for sharp reductions in their greenhouse gas (GHG) emissions and adopted a long-term approach to address climate change that includes regulation of emissions from individual emitters and source categories. There are large CH4 and N2O emissions sources in the state, predominantly in the agricultural and waste management sector. While these two gases account for < 10% of total annual greenhouse gas emissions of the state, large uncertainties exist in their `bottom-up' accounting in the state GHG inventory. Additionally, an increasing number of `top-down' studies based on ambient observations point towards underestimation of their emissions in the inventory. Three intensive field observation campaigns that were spatially and temporally diverse took place between 2010 and 2013 in the Central Valley of California where the largest known sources of CH4 and N2O (e.g. agricultural systems and dairies) and potentially significant CH4 sources (e.g. oil and gas extraction) are located. The CalNex (California Nexus - Research at the Nexus of Air Quality and Climate Change) field campaign during summer 2010 (May 15 - June 30) took place in the urban core of Bakersfield in the southern San Joaquin Valley, a city whose economy is built around agriculture and the oil and gas industry. During summer of 2011, airborne measurements were performed over a large spatial domain, all across and around the Central Valley as part of the CABERNET (California Airborne BVOC Emission Research in Natural Ecosystem Transects) study. Next, a one-year continuous field campaign (WGC 2012-13, June 2012 - August 2013) was conducted at the Walnut Grove tall tower near the Sacramento-San Joaquin River Delta in the Central Valley. Through analysis of these field measurements, this dissertation presents the apportionment of observed CH4 and N2O concentration enhancements into major source categories along with direct emissions estimates from airborne observations. We perform high-precision measurements of greenhouse gases using gas analyzers based on absorption spectroscopy, and other source marker volatile organic compounds (VOCs) using state of the art VOC measurement systems (e.g. proton transfer reaction mass spectrometry). We combine these measurements with a statistical source apportionment technique called positive matrix factorization (PMF) to evaluate and investigate the major local sources of CH4 and N2O during CalNex and Walnut Grove campaigns. In the CABERNET study, we combine measurements with an airborne approach to a well-established micrometeorological technique (eddy-covariance method) to derive CH4 fluxes over different source regions in the Central Valley. In the CalNex experiments, we demonstrate that dairy and livestock remains the largest source sector of non-CO2 greenhouse gases in the San Joaquin Valley contributing most of the CH4 and much of the measured N2O at Bakersfield. Agriculture is observed to provide another major source of N2O, while vehicle emissions are found to be an insignificant source of N2O, contrary to the current statewide greenhouse gas inventory which includes vehicles as a major source. Our PMF source apportionment also produces an evaporative/fugitive factor but its relative lack of CH4 contributions points to removal processes from vented emissions in the surrounding O&G industry and the overwhelming dominance of the dairy CH4 source. In the CABERNET experiments, we report enhancements of CH4 from a number of sources spread across the spatial domain of the Central Valley that improves our understanding of their distribution and relative strengths. We observe large enhancements of CH4 mixing ratios over the dairy and feedlot intensive regions of Central Valley corresponding with significant flux estimates that are larger than CH4 emission rates reported in the greenhouse gas inventory. We find evidence of significant CH 4 emissions from fugitive and/or vented sources and cogeneration plants in the oil and gas fields of Kern County, all of which are minor to insignificant CH4 sources in the current greenhouse gas inventory. The CABERNET campaign represents the first successful implementation of airborne eddy covariance technique for CH4 flux measurements. At Walnut Grove, we demonstrate the seasonal and temporal dependence of CH4 and N2O sources in the Central Valley. Applying PMF analysis on seasonal GHG-VOC data sets, we again identify dairies and livestock as the dominant source of CH4. A clear temporal dependence of emissions originating from a wetlands / Delta CH4 source is observed while CH4 contributions are also observed from a source originating from upwind urban and natural gas extraction activities. The agricultural soil management source of N2O has a seasonal dependence coincident with the agricultural growing season (and hence, fertilizer use) accounting for a majority of the N2O enhancements during spring and summers but being reduced to a negligible source during late fall and winters when manure management N2O emissions from dairy and livestock dominate the relative distribution. N2O is absent from the 'urban' source, in contrast to the significant contribution to the statewide N2O inventory from vehicle emissions. The application of greenhouse gas source apportionment using VOC tracers as identification tools at two independent sites in the Central Valley over vastly different temporal resolutions provide significant insights into the regional distribution of major CH4 sources. Direct airborne eddy covariance measurements provide a unique opportunity to constrain CH 4 emissions in the Central Valley over regional spatial scales that are not directly observable by ground-based methods. Airborne observations provide identification of 'hotspots' and under-inventoried CH4 sources, while airborne eddy covariance enables quantification of emissions from those area sources that are largely composed of arbitrarily located minor point sources (e.g. dairies and oil fields). The top-down analysis provides confirmation of the dominance of dairy and livestock source for methane emissions in California. Minor but significant contributions to methane emissions are observed from oil and gas extraction, rice cultivation and wetlands; the estimates for these sectors being either negligible (e.g. wetlands) or highly uncertain (e.g. oil and gas extraction) in the statewide inventories and probably underestimated as a proportion of the total inventory. The top-down analysis also confirms agricultural soil management and dairy and livestock as the two principal sources of N2O consistent with the inventory, but shows that N2O contributions attributed to the transportation sector are overestimated in the statewide inventory. These new top down constraints should be used to correct these errors in the current bottom-up inventory, which is a critical step for future assessments of the efficacy of emission reduction regulations. Particularly, measurement techniques like vehicle dynamometer emission calculations (for transportation sources), source-specific short range ground-based inverse dispersion (for dairy and livestock sources), airborne eddy covariance and airborne mass balance approach based emissions estimation (over oil and gas fields) and ground based eddy-covariance (for wetlands and agriculture sector) can be used effectively to generate direct emissions estimates for methane and nitrous oxide that help update and improve the accuracy of the state inventory.

Stoichiometry of water-soluble ions in PM2.5: Application in source apportionment for a typical industrial city in semi-arid region, Northwest China

NASA Astrophysics Data System (ADS)

Zhou, Haijun; Lü, Changwei; He, Jiang; Gao, Manshu; Zhao, Boyi; Ren, Limin; Zhang, Lijun; Fan, Qingyun; Liu, Tao; He, Zhongxiang; Dudagula; Zhou, Bin; Liu, Hualin; Zhang, Yu

2018-05-01

Water-soluble ions (WSIs) are major components of PM2.5 and it is valuable for understanding physical and chemical characteristics, sources, behaviors and formation mechanism of WSIs. Baotou is a traditionally industrial city in semi-arid region and frequently subjected to dust storms from March to May. In recent years, air pollution has been listed as one of the most important environmental problems in Baotou. To investigate the seasonal variations and sources of WSIs in PM2.5, the WSIs including SO42-, NO3-, Cl-, F-, NH4+, K+, Na+, Ca2+ and Mg2+ were monitored at six urban sites in Baotou. The results showed that high concentrations of Ca2+ and Na+ were found responding to dust storm events, while high concentrations of SO42-, NO3-, NH4+, K+ and Cl- were observed during haze days. The correlations analysis indicated that excess sulfuric and nitric acid was likely neutralized by carbonate minerals such as calcite, aragonite and dolomite in normal days and cations were fully neutralized during all the sampling periods, while cations were excessive in dust storm days. The concentrations of [NH4+ + SO42- + NO3-], [Na+ + Ca2+ + Mg2+] and [Cl- + K+ + F-] indicated the northwest and southeast region of Baotou presented comparatively high contributions of secondary aerosol and crustal dust, respectively, which were mainly related to the industrial distribution and urbanization process. The cluster analysis, ternary diagram and principal component analysis have a good agreement in source apportionment, where crustal dust sources, secondary aerosol source and the mixture of coal combustion, biomass burning and industrial pollution sources were the main sources of WSIs in PM2.5. The seasonal pattern of sulfur oxidation ratio (SOR) was September > April > November > January, while the nitrogen oxidation ratio (NOR) April > January > November > September in Baotou. This work evaluated the seasonal variation, distribution and source of WSIs on the basis of its stoichiometry in PM2.5, which help to explore the potential sources of these inorganic aerosols and provide scientific suggestion for air quality improvement in Baotou.

Source apportionment of speciated PM10 in the United Kingdom in 2008: Episodes and annual averages

NASA Astrophysics Data System (ADS)

Redington, A. L.; Witham, C. S.; Hort, M. C.

2016-11-01

The Lagrangian atmospheric dispersion model NAME (Numerical Atmospheric-dispersion Modelling Environment), has been used to simulate the formation and transport of PM10 over North-West Europe in 2008. The model has been evaluated against UK measurement data and been shown to adequately represent the observed PM10 at rural and urban sites on a daily basis. The Lagrangian nature of the model allows information on the origin of pollutants (and hence their secondary products) to be retained to allow attribution of pollutants at receptor sites back to their sources. This source apportionment technique has been employed to determine whether the different components of the modelled PM10 have originated from UK, shipping, European (excluding the UK) or background sources. For the first time this has been done to evaluate the composition during periods of elevated PM10 as well as the annual average composition. The episode data were determined by selecting the model data for each hour when the corresponding measurement data was >50 μg/m3. All the modelled sites show an increase in European pollution contribution and a decrease in the background contribution in the episode case compared to the annual average. The European contribution is greatest in southern and eastern parts of the UK and decreases moving northwards and westwards. Analysis of the speciated attribution data over the selected sites reveals that for 2008, as an annual average, the top three contributors to total PM10 are UK primary PM10 (17-25%), UK origin nitrate aerosol (18-21%) and background PM10 (11-16%). Under episode conditions the top three contributors to modelled PM10 are UK origin nitrate aerosol (12-33%), European origin nitrate aerosol (11-19%) and UK primary PM10 (12-18%).

Role of lightning phenomenon over surface O3 and NOx at a semi-arid tropical site Hyderabad, India: inter-comparison with satellite retrievals

NASA Astrophysics Data System (ADS)

Venkanna, R.; Nikhil, G. N.; Sinha, P. R.; Siva Rao, T.; Swamy, Y. V.

2016-08-01

The influence of lightning over surface-level trace gases was examined for pre-monsoon and monsoon seasons in the year 2012. Lightning events were measured using ground-based electric field monitor (EFM) and space-based lightning imaging sensor (LIS). The results showed that lightning frequency was higher during pre-monsoon period compared to monsoon, which is in good agreement with the satellite retrievals. The increase in concentration of NOx on lightning event led to a subsequent decrease in surface O3 due to the titration reaction. Source apportionment study of SO2/NOx (S/N) and CO/NOx (C/N) ratios and poor correlation of NOx vs CO and NOx vs SO2 on the lightning day confirmed the emission of NOx from dissimilar sources.

Composition of the council of representatives: Report on the apportionment ballot for representation year 2011.

PubMed

2010-01-01

Each year, the apportionment ballot is used to determine how many representatives each division and state, provincial, and territorial association will have on the Council of Representatives. The system is described in Article V, Sections 6 and 7, of the American Psychological Association (APA) Bylaws. Briefly, all APA fellows, members, and voting associates are sent an apportionment ballot on or before November 1. Voting members indicate the division( s) and/or state, provincial, or territorial association(s) through which they desire to have their interests represented on Council in the following year by allocating a total of 10 votes to one or more of these groups. Beginning with the 2003 legislative year the total number of representatives (seats) on Council was set at 162. This article reports the apportionment ballot for representation year 2001. 2010 APA, all rights reserved.

Application of a combined approach including contamination indexes, geographic information system and multivariate statistical models in levels, distribution and sources study of metals in soils in Northern China

PubMed Central

Huang, Kuixian; Luo, Xingzhang

2018-01-01

The purpose of this study is to recognize the contamination characteristics of trace metals in soils and apportion their potential sources in Northern China to provide a scientific basis for basic of soil environment management and pollution control. The data set of metals for 12 elements in surface soil samples was collected. The enrichment factor and geoaccumulation index were used to identify the general geochemical characteristics of trace metals in soils. The UNMIX and positive matrix factorizations (PMF) models were comparatively applied to apportion their potential sources. Furthermore, geostatistical tools were used to study the spatial distribution of pollution characteristics and to identify the affected regions of sources that were derived from apportionment models. The soils were contaminated by Cd, Hg, Pb and Zn to varying degree. Industrial activities, agricultural activities and natural sources were identified as the potential sources determining the contents of trace metals in soils with contributions of 24.8%–24.9%, 33.3%–37.2% and 38.0%–41.8%, respectively. The slightly different results obtained from UNMIX and PMF might be caused by the estimations of uncertainty and different algorithms within the models. PMID:29474412

Effective numbers in the partitioning of biological diversity.

PubMed

Gregorius, Hans-Rolf

2016-11-21

Admissible measures of diversity allow specification of the number of types (species, alleles, etc.) that are "effectively" involved in producing the diversity (the "diversity effective number", also referred to as "true diversity") of a community or population. In metacommunities, effective numbers additionally serve in partitioning the total diversity (symbolized by γ) into one component summarizing the diversity within communities (symbolized by α) and an independent component summarizing the differences between communities (symbolized by β). There is growing consensus that the β-component should be treated in terms of an effective number of "distinct" communities in the metacommunity. Yet, the notion of distinctness is shown in the present paper to remain conceptually ambiguous at least with respect to the diversity within the "distinct" communities. To overcome this ambiguity and to provide the means for designing further desirable effective numbers, a new approach is taken that involves a generalized concept of effective number. The approach relies on first specifying the distributional characteristics of partitioning diversity among communities (among which are differentiation, where the same types tend to occur in the same communities, and apportionment, where different types tend to occur in different communities), then developing the indices which measure these characteristics, and finally inferring the effective numbers from these indices. (1) The β-component reflects apportionment characteristics of metacommunity structure and is quantified by the "apportionment effective number" of communities (number of effectively monomorphic communities). Since differentiation between communities arises only as a side effect of apportionment, the common interpretation of the β-component in terms of differentiation is unwarranted. (2) Multiplicative as well as additive methods of partitioning the total type diversity (γ) involve apportionment effective numbers of communities that are based on different apportionment indices. (3) "Differentiation effective numbers" of communities exist but do not conform with the classical concept of partitioning total type diversity into components within and between communities. (4) Differentiation characteristics are measured as effective numbers of distinct types (rather than communities) from the dual perspective, in which the roles of type and community membership are exchanged. This is relevant e.g. in studies of endemism and competitive exclusion. (5) For Shannon-Wiener diversity, all of the differentiation and apportionment effective numbers are equal, with the exception of those representing additive partitioning. (6) Under either perspective, that is dual or non-dual, measures of compositional differentiation (as originally suggested for the assessment of β-diversity) do not figure in the partitioning of total diversity into components, since they do not build on the intrinsic concept of diversity. Copyright © 2016 Elsevier Ltd. All rights reserved.

An evaluation of catchment-scale phosphorus mitigation using load apportionment modelling.

PubMed

Greene, S; Taylor, D; McElarney, Y R; Foy, R H; Jordan, P

2011-05-01

Functional relationships between phosphorus (P) discharge and concentration mechanisms were explored using a load apportionment model (LAM) developed for use in a freshwater catchment in Ireland with fourteen years of data (1995-2008). The aim of model conceptualisation was to infer changes in point and diffuse sources from catchment P loading during P mitigation, based upon a dataset comprising geospatial and water quality data from a 256km(2) lake catchment in an intensively farmed drumlin region of the midlands of Ireland. The model was calibrated using river total P (TP), molybdate reactive P (MRP) and runoff data from seven subcatchments. Temporal and spatial heterogeneity of P sources existed within and between subcatchments; these were attributed to differences in agricultural intensity, soil type and anthropogenically-sourced effluent P loading. Catchment rivers were sensitive to flow regime, which can result in eutrophication of rivers during summer and lake enrichment from frequent flood events. For one sewage impacted river, the LAM estimated that point sourced P contributed up to of 90% of annual MRP load delivered during a hydrological year and in this river point P sources dominated flows up to 92% of days. In the other rivers, despite diffuse P forming a majority of the annual P exports, point sources of P dominated flows for up to 64% of a hydrological year. The calibrated model demonstrated that lower P export rates followed specific P mitigation measures. The LAM estimated up to 80% decreases in point MRP load after enhanced P removal at waste water treatments plants in urban subcatchments and the implementation of septic tank and agricultural bye-laws in rural subcatchments. The LAM approach provides a way to assess the long-term effectiveness of further measures to reduce P loadings in EU (International) River Basin Districts and subcatchments. Copyright © 2011 Elsevier B.V. All rights reserved.

Source contributions of urban PM2.5 in the Beijing-Tianjin-Hebei region: Changes between 2006 and 2013 and relative impacts of emissions and meteorology

NASA Astrophysics Data System (ADS)

Li, Xin; Zhang, Qiang; Zhang, Yang; Zheng, Bo; Wang, Kai; Chen, Ying; Wallington, Timothy J.; Han, Weijian; Shen, Wei; Zhang, Xiaoye; He, Kebin

2015-12-01

Anthropogenic emissions in China have been controlled for years to improve ambient air quality. However, severe haze events caused by atmospheric aerosols with aerodynamic diameter less than or equal to 2.5 μm (PM2.5) have continued to occur, especially in the Beijing-Tianjin-Hebei (BTH) region. The Chinese government has set an ambitious goal to reduce urban PM2.5 concentrations by 25% in BTH by 2017 relative to the 2012 levels. Source apportionment (SA) is necessary to the development of the effective emission control strategies. In this work, the Comprehensive Air Quality Model with extensions (CAMx) with the Particulate Source Apportionment Technology (PSAT) is applied to the China domain for the years 2006 and 2013. Ambient surface concentrations of PM2.5 and its components are generally well reproduced. To quantify the contributions of each emission category or region to PM2.5 in BTH, the total emissions are divided into 7 emission categories and 11 source regions. The source contributions determined in this work are generally consistent with results from previous work. In 2013, the industrial (44%) and residential (27%) sectors are the dominant contributors to urban PM2.5 in BTH. The residential sector is the largest contributor in winter; the industry sector dominates in other seasons. A slight increasing trend (+3% for industry and +6% for residential) is found in 2013 relative to 2006, necessitating more attention to these two sectors. Local emissions make the largest contribution (40%-60%) for all receptors. Change of source contribution of PM2.5 in Beijing and northern Hebei are dominate by change of local emission. However, for Tianjin, and central and southern Hebei, change of meteorology condition are as important as change of emission, because regional inflow in these areas is more important than in Beijing and northern Hebei and can increase under unfavorable weather conditions, indicating a strong need for regional joint emission control efforts. The results in this study enhance the quantitative understanding of the source-receptor relationships and provide an important basis for policymaking to advance the control of PM2.5 pollution in China.

Highway Funding: The Federal Highway Administration's Funding Apportionment Model

DOT National Transportation Integrated Search

1997-06-01

The Federal Highway Administration (FHWA) has developed and is operating, through the use of a contractor, a new apportionment model to estimate the expected distribution of federal-aid funds under various legislative proposals. Because of the import...

Community managed forests dominate the catchment sediment cascade in the mid-hills of Nepal: A compound-specific stable isotope analysis.

PubMed

Upadhayay, Hari Ram; Smith, Hugh G; Griepentrog, Marco; Bodé, Samuel; Bajracharya, Roshan Man; Blake, William; Cornelis, Wim; Boeckx, Pascal

2018-05-08

Soil erosion by water is critical for soil, lake and reservoir degradation in the mid-hills of Nepal. Identification of the nature and relative contribution of sediment sources in rivers is important to mitigate water erosion within catchments and siltation problems in lakes and reservoirs. We estimated the relative contribution of land uses (i.e. sources) to suspended and streambed sediments in the Chitlang catchment using stable carbon isotope signature (δ 13 C) of long-chain fatty acids as a tracer input for MixSIAR, a Bayesian mixing model used to apportion sediment sources. Our findings reveal that the relative contribution of land uses varied between suspended and streambed sediment, but did not change over the monsoon period. Significant over- or under-prediction of source contributions could occur due to overlapping source tracer values, if source groups are classified on a catchment-wide basis. Therefore, we applied a novel deconvolutional framework of MixSIAR (D-MixSIAR) to improve source apportionment of suspended sediment collected at tributary confluences (i.e. sub-catchment level) and at the outlet of the entire catchment. The results indicated that the mixed forest was the dominant (41 ± 13%) contributor of sediment followed by broadleaf forest (15 ± 8%) at the catchment outlet during the pre-wet season, suggesting that forest disturbance as well as high rainfall and steep slopes interact for high sediment generation within the study catchment. Unpaved rural road tracks located on flat and steep slopes (11 ± 8 and 9 ± 7% respectively) almost equally contributed to the sediment. Importantly, agricultural terraces (upland and lowland) had minimal contribution (each <7%) confirming that proper terrace management and traditional irrigation systems played an important role in mitigating sediment generation and delivery. Source contributions had a small temporal, but large spatial, variation in the sediment cascade of Chitlang stream. D-MixSIAR provided significant improvement regarding spatially explicit sediment source apportionment within the entire catchment system. This information is essential to prioritize implementation measures to control erosion in community managed forests to reduce sediment loadings to Kulekhani hydropower reservoir. In conclusion, using compound-specific stable isotope (CSSI) tracers for sediment fingerprinting in combination with a deconvolutional Bayesian mixing model offers a versatile approach to deal with the large tracer variability within catchment land uses and thus to successfully apportion multiple sediment sources. Copyright © 2018. Published by Elsevier B.V.

U.S. Marine Corps Concepts & Programs 2009

DTIC Science & Technology

2009-01-01

war efforts in the CENTCOM AOR — that will demand balanced apportionment of limited re- sources . In this, the Marine Corps has identified four...Strike Fighter (JSF) Transition Plan 123 MV-22 Osprey Program 125 H-1 Upgrade (UH-1Y Huey/AH-1Z Cobra) 127 KC-130 Hercules 129 CH-53K Heavy Lift...leading joint-service development of our light, medium and heavy tactical wheeled vehicles for the joint force. The Expeditionary Fighting Vehicle (EFV

Characteristics and Source Apportionment of Marine Aerosols over East China Sea Using a Source-oriented Chemical Transport Model

NASA Astrophysics Data System (ADS)

Kang, M.; Zhang, H.; Fu, P.

2017-12-01

Marine aerosols exert a strong influence on global climate change and biogeochemical cycling, as oceans cover beyond 70% of the Earth's surface. However, investigations on marine aerosols are relatively limited at present due to the difficulty and inconvenience in sampling marine aerosols as well as their diverse sources. East China Sea (ECS), lying over the broad shelf of the western North Pacific, is adjacent to the Asian mainland, where continental-scale air pollution could impose a heavy load on the marine atmosphere through long-range atmospheric transport. Thus, contributions of major sources to marine aerosols need to be identified for policy makers to develop cost effective control strategies. In this work, a source-oriented version of the Community Multiscale Air Quality (CMAQ) model, which can directly track the contributions from multiple emission sources to marine aerosols, is used to investigate the contributions from power, industry, transportation, residential, biogenic and biomass burning to marine aerosols over the ECS in May and June 2014. The model simulations indicate significant spatial and temporal variations of concentrations as well as the source contributions. This study demonstrates that the Asian continent can greatly affect the marine atmosphere through long-range transport.

Source apportionment of organic aerosol across Houston, TX during DISCOVER-AQ

NASA Astrophysics Data System (ADS)

Yoon, S.; Clark, A. E.; Ortiz, S. M.; Usenko, S.; Sheesley, R. J.

2015-12-01

As part of the ground-based sampling efforts during DISCOVER-AQ's Houston month-long campaign in September 2013, atmospheric particulate matter (PM) samples were collected at four sites: Moody Tower (urban), Manvel Croix (southern suburb), Conroe (northern suburb), and La Porte (urban industrial). The Houston metropolitan area, especially the Houston Ship Channel, is a densely industrialized urban city with large concentrations of petroleum refining, petrochemical manufacturing, and heavy traffic during peak hours. Due to these and other emission sources, the area is heavily impacted by ambient PM. This study will be looking at fine PM (diameter less than 2.5µm, PM2.5) from all four sites. PM2.5fraction is relevant for understanding fate and transport of organic contaminants and is widely known to negatively impact human health. Chemical analysis including radiocarbon (14C) and organic tracer measurements (polycyclic aromatic hydrocarbons, alkanes, hopanes, steranes, and levoglucosan) were used for source apportionment. The 14C measurements constrained CMB results to estimate both primary and secondary contributions to total organic carbon (TOC). Results indicate that Moody Tower had consistent primary motor vehicle exhaust contribution (18-27%) and a fossil secondary organic aerosol (SOA) contribution from 5-33% depending on atmospheric conditions. Conroe had a lower contribution of motor vehicle exhaust (5-10%) and similarly variable fraction of fossil SOA (4-25%). Manvel Croix had an interim motor vehicle contribution (9-15%) with a variable fossil SOA (5-30%). For contemporary OC, there was minimal contribution of wood smoke during examined weeks (0-9%) but larger contributor of biogenic SOA ranging from 40-75% at Moody Tower, 56-81% at Manvel Croix and 60-79% at Conroe. Overall, the motor vehicle contribution was consistent at each site during the analysis week, biogenic SOA was consistently high, while fossil SOA showed the most variability.

Quantification of Methane and Nitrous Oxide Emissions from Wastewater Collection Systems (Cincinnati, Ohio, USA)

NASA Astrophysics Data System (ADS)

Fries, A. E.; Townsend-Small, A.; Shuster, W.; Schifman, L. A.

2016-12-01

Greenhouse gas emissions from urban areas is an emerging topic in environmental science, but source apportionment of these emissions, particularly for methane (CH4) and nitrous oxide (N2O), is still underway. Here we present an analysis of CH4 and N2O sources from urban pipelines in Cincinnati, Ohio, USA. Leaks from manholes and sewer grates in Cincinnati are found by using a Bascom Turner Gas Rover to indicate CH4 enhancements, along with spatial data for CH4 enhancements at street level from previously published work. When possible, the atmospheric flux of CH4 and N2O of these leaks are quantified by using a flux chamber method. Source apportionment is determined by using carbon and hydrogen stable isotope ratios (13C and D) and CH4 to N2O ratios. Biogenic CH4 has a δ13C of approximately -55‰ and δD of approximately -270‰, whereas thermogenic CH4 has a δ13C of approximately -45‰ and δD of approximately -150‰. Biogenic CH4 may also co-occur with N2O, whereas thermogenic natural gas does not contain N2O. Contrary to our expectations, we found a portion of CH4 enhancements that are biogenic CH4, presumably from sewer gas, whereas most studies have assumed them to be natural gas leaks. In the future we will be working on determining the exact proportion of biogenic and thermogenic CH4 in street leaks and further quantifying CH4 and N2O emissions throughout Cincinnati. Our work indicates that CH4 leaks in cities may be a mixture of sewer gas and natural gas, especially in cities like Cincinnati where natural gas pipelines have been replaced with less leak-prone pipe materials.

Source Apportionment of the Size-Fractionated Urban Aerosols in and around Kolkata, India

NASA Astrophysics Data System (ADS)

Sarkar, Ujjaini; Haque, Monirul; Roy, Rajdeep; Chakraborty, Sanjoy

Our main objective was to estimate the heavy metals like the Lead, Mercury, Cadmium, Sodium, Potassium, Calcium, Aluminium, and Iron, in addition to ammonium, chloride, nitrate, and sulphate ions, by Atomic Absorption Spectrophotometry and Ion Chromatography and apportion the most probable sources using the Chemical Mass Balance Model. The three urban locations of Behala Chowrasta, Rabindra Sadan, and Shyam Bazaar Five Points were chosen within the city of Kolkata. One rural location was chosen at the Indian Institute of Technology campus, Kharagpur, a rural site in the Midnapur District of the state of West Bengal, India. The results look quite encouraging.

Spatial and temporal variations of loads and sources of total and dissolved Phosphorus in a set of rivers (Western France).

NASA Astrophysics Data System (ADS)

Legeay, Pierre-Louis; Moatar, Florentina; Gascuel-Odoux, Chantal; Gruau, Gérard

2015-04-01

In intensive agricultural regions with important livestock farming, long-term land application of Phosphorus (P) both as chemical fertilizer and animal wastes, have resulted in elevated P contents in soils. Since we know that high P concentrations in rivers is of major concern, few studies have been done at to assess the spatiotemporal variability of P loads in rivers and apportionment of point and nonpoint source in total loads. Here we focus on Brittany (Western France) where even though P is a great issue in terms of human and drinking water safety (cyano-toxins), environmental protection and economic costs for Brittany with regards to the periodic proliferations of cyanobacteria that occur every year in this region, no regional-scale systematic study has been carried out so far. We selected a set of small rivers (stream order 3-5) with homogeneous agriculture and granitic catchment. By gathering data from three water quality monitoring networks, covering more than 100 measurements stations, we provide a regional-scale quantification of the spatiotemporal variability of dissolved P (DP) and total P (TP) interannual loads from 1992 to 2012. Build on mean P load in low flows and statistical significance tests, we developed a new indicator, called 'low flow P load' (LFP-load), which allows us to determine the importance of domestic and industrial P sources in total P load and to assess their spatiotemporal variability compared to agricultural sources. The calculation and the map representation of DP and TP interannual load variations allow identification of the greatest and lowest P contributory catchments over the study period and the way P loads of Brittany rivers have evolved through time. Both mean DP and TP loads have been divided by more than two over the last 20 years. Mean LFDP-load decreased by more than 60% and mean LFTP-load by more than 45% on average over the same period showing that this marked temporal decrease in total load is largely due to the decrease of domestic and industrial P effluents. A global shift in P inputs apportionment to freshwaters thus occurred in Brittany since 20 years as agricultural nonpoint sources now contribute a greater portion of inputs showing the efficiency of the recent control of point sources by enhancement of water treatment plant and removal of phosphates in detergents. The spatialized P loads provided by this study could give a basis for a better understanding of the factors that drives the P transfers in Brittany soils and hotspots of P emissions while the LFP-load indicator can be a tool to assess effects of point-source P mitigation plans.

Development of a methodology examining the behaviours of VOCs source apportionment with micro-meteorology analysis in an urban and industrial area.

PubMed

Xiang, Yang; Delbarre, Hervé; Sauvage, Stéphane; Léonardis, Thierry; Fourmentin, Marc; Augustin, Patrick; Locoge, Nadine

2012-03-01

During summer 2009, online measurements of 25 Volatile Organic Compounds (VOCs) from C6 to C10 as well as micro-meteorological parameters were simultaneously performed in the industrial city of Dunkerque. With the obtained data set, we developed a methodology to examine how the contributions of different source categories depend on atmospheric turbulences, and the results provided identification of emission modes. Eight factors were resolved by using Positive Matrix Factorization model and three of them were associated with mixed sources. The observed behaviours of contributions with turbulences lead to attribute some factors with sources at ground level, and some other factors with sources in the upper part of surface layer. The impact of vertical turbulence on the pollutant dispersion is also affected by the distance between sources and receptor site. Copyright © 2011 Elsevier Ltd. All rights reserved.

Spatial and temporal variations of aerosols around Beijing in summer 2006: Model evaluation and source apportionment

NASA Astrophysics Data System (ADS)

Matsui, H.; Koike, M.; Kondo, Y.; Takegawa, N.; Kita, K.; Miyazaki, Y.; Hu, M.; Chang, S.-Y.; Blake, D. R.; Fast, J. D.; Zaveri, R. A.; Streets, D. G.; Zhang, Q.; Zhu, T.

2009-01-01

Regional aerosol model calculations were made using the Weather Research and Forecasting (WRF)-Community Multiscale Air Quality (CMAQ) and WRF-chem models to study spatial and temporal variations of aerosols around Beijing, China, in the summer of 2006, when the Campaigns of Air Quality Research in Beijing and Surrounding Region 2006 (CAREBeijing) intensive campaign was conducted. Model calculations captured temporal variations of primary (such as elemental carbon (EC)) and secondary (such as sulfate) aerosols observed in and around Beijing. The spatial distributions of aerosol optical depth observed by the MODIS satellite sensors were also reproduced over northeast China. Model calculations showed distinct differences in spatial distributions between primary and secondary aerosols in association with synoptic-scale meteorology. Secondary aerosols increased in air around Beijing on a scale of about 1000 × 1000 km2 under an anticyclonic pressure system. This air mass was transported northward from the high anthropogenic emission area extending south of Beijing with continuous photochemical production. Subsequent cold front passage brought clean air from the north, and polluted air around Beijing was swept to the south of Beijing. This cycle was repeated about once a week and was found to be responsible for observed enhancements/reductions of aerosols at the intensive measurement sites. In contrast to secondary aerosols, the spatial distributions of primary aerosols (EC) reflected those of emissions, resulting in only slight variability despite the changes in synoptic-scale meteorology. In accordance with these results, source apportionment simulations revealed that primary aerosols around Beijing were controlled by emissions within 100 km around Beijing within the preceding 24 h, while emissions as far as 500 km and within the preceding 3 days were found to affect secondary aerosols.

Air quality analysis of MDT transportation improvements, cost-effectiveness analysis of the MACI Program.

DOT National Transportation Integrated Search

2004-03-01

"Under TEA-21, part of Montana's CMAQ apportionment is dedicated to Missoula and at the direction of the : Montana Transportation Commission, the Montana Department of Transportation (MDT) directs the remainder of : the CMAQ apportionment to areas in...

Air quality analysis of MDT transportation improvements : cost-effectiveness analysis of the MACI program.

DOT National Transportation Integrated Search

2004-03-01

Under TEA-21, part of Montana's CMAQ apportionment is dedicated to Missoula and at the direction of the : Montana Transportation Commission, the Montana Department of Transportation (MDT) directs the remainder of : the CMAQ apportionment to areas in ...

47 CFR 36.142 - Categories and apportionment procedures.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 2 2010-10-01 2010-10-01 false Categories and apportionment procedures. 36.142 Section 36.142 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES... Customer Premises Equipment that was detariffed pursuant to the Second Computer Inquiry decision. It shall...

47 CFR 36.142 - Categories and apportionment procedures.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 2 2013-10-01 2013-10-01 false Categories and apportionment procedures. 36.142 Section 36.142 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES... Customer Premises Equipment that was detariffed pursuant to the Second Computer Inquiry decision. It shall...

47 CFR 36.142 - Categories and apportionment procedures.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 2 2011-10-01 2011-10-01 false Categories and apportionment procedures. 36.142 Section 36.142 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES... Customer Premises Equipment that was detariffed pursuant to the Second Computer Inquiry decision. It shall...

47 CFR 36.142 - Categories and apportionment procedures.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 47 Telecommunication 2 2012-10-01 2012-10-01 false Categories and apportionment procedures. 36.142 Section 36.142 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES... Customer Premises Equipment that was detariffed pursuant to the Second Computer Inquiry decision. It shall...

47 CFR 36.142 - Categories and apportionment procedures.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 2 2014-10-01 2014-10-01 false Categories and apportionment procedures. 36.142 Section 36.142 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES... Customer Premises Equipment that was detariffed pursuant to the Second Computer Inquiry decision. It shall...

Source apportionment of atmospheric mercury pollution in China using the GEOS-Chem model.

PubMed

Wang, Long; Wang, Shuxiao; Zhang, Lei; Wang, Yuxuan; Zhang, Yanxu; Nielsen, Chris; McElroy, Michael B; Hao, Jiming

2014-07-01

China is the largest atmospheric mercury (Hg) emitter in the world. Its Hg emissions and environmental impacts need to be evaluated. In this study, China's Hg emission inventory is updated to 2007 and applied in the GEOS-Chem model to simulate the Hg concentrations and depositions in China. Results indicate that simulations agree well with observed background Hg concentrations. The anthropogenic sources contributed 35-50% of THg concentration and 50-70% of total deposition in polluted regions. Sensitivity analysis was performed to assess the impacts of mercury emissions from power plants, non-ferrous metal smelters and cement plants. It is found that power plants are the most important emission sources in the North China, the Yangtze River Delta (YRD) and the Pearl River Delta (PRD) while the contribution of non-ferrous metal smelters is most significant in the Southwest China. The impacts of cement plants are significant in the YRD, PRD and Central China. Copyright © 2014 Elsevier Ltd. All rights reserved.

Constrained Source Apportionment of Coarse Particulate Matter and Selected Trace Elements in Three Cities from the Multi-Ethnic Study of Atherosclerosis

PubMed Central

Sturtz, Timothy M.; Adar, Sara D.; Gould, Timothy; Larson, Timothy V.

2016-01-01

PM10-2.5 mass and trace element concentrations were measured in Winston-Salem, Chicago, and St. Paul at up to 60 sites per city during two different seasons in 2010. Positive Matrix Factorization (PMF) was used to explore the underlying sources of variability. Information on previously reported PM10-2.5 tire and brake wear profiles was used to constrain these features in PMF by prior specification of selected species ratios. We also modified PMF to allow for combining the measurements from all three cities into a single model while preserving city-specific soil features. Relatively minor differences were observed between model predictions with and without the prior ratio constraints, increasing confidence in our ability to identify separate brake wear and tire wear features. Brake wear, tire wear, fertilized soil, and re-suspended soil were found to be important sources of copper, zinc, phosphorus, and silicon respectively across all three urban areas. PMID:27468256

Constrained source apportionment of coarse particulate matter and selected trace elements in three cities from the multi-ethnic study of atherosclerosis

NASA Astrophysics Data System (ADS)

Sturtz, Timothy M.; Adar, Sara D.; Gould, Timothy; Larson, Timothy V.

2014-02-01

PM10-2.5 mass and trace element concentrations were measured in Winston-Salem, Chicago, and St. Paul at up to 60 sites per city during two different seasons in 2010. Positive Matrix Factorization (PMF) was used to explore the underlying sources of variability. Information on previously reported PM10-2.5 tire and brake wear profiles was used to constrain these features in PMF by prior specification of selected species ratios. We also modified PMF to allow for combining the measurements from all three cities into a single model while preserving city-specific soil features. Relatively minor differences were observed between model predictions with and without the prior ratio constraints, increasing confidence in our ability to identify separate brake wear and tire wear features. Brake wear, tire wear, fertilized soil, and resuspended soil were found to be important sources of copper, zinc, phosphorus, and silicon, respectively, across all three urban areas.

Metals and metalloids in atmospheric dust: Use of lead isotopic analysis for source apportionment

NASA Astrophysics Data System (ADS)

Felix Villar, Omar I.

Mining activities generate aerosol in a wide range of sizes. Smelting activities produce mainly fine particles (<1 microm). On the other hand, milling, crushing and refining processes, as well tailings management, are significant sources of coarse particles (> 1 microm). The adverse effects of aerosols on human health depend mainly on two key characteristics: size and chemical composition. One of the main objectives of this research is to analyze the size distribution of contaminants in aerosol produced by mining operations. For this purpose, a Micro-Orifice Uniform Deposit Impactor (MOUDI) was utilized. Results from the MOUDI samples show higher concentrations of the toxic elements like lead and arsenic in the fine fraction (<1 microm). Fine particles are more likely to be deposited in the deeper zones of the respiratory system; therefore, they are more dangerous than coarse particles that can be filtered out in the upper respiratory system. Unfortunately, knowing the total concentration of contaminants does not give us enough information to identify the source of contamination. For this reason, lead isotopes have been introduced as fingerprints for source apportionment. Each source of lead has specific isotopic ratios; by knowing these ratios sources can be identified. During this research, lead isotopic ratios were analyzed at different sites and for different aerosol sizes. From these analyses it can be concluded that lead isotopes are a powerful tool to identify sources of lead. Mitigation strategies could be developed if the source of contamination is well defined. Environmental conditions as wind speed, wind direction, relative humidity and precipitation have an important role in the concentration of atmospheric dust. Dry environments with low relative humidity are ideal for the transport of aerosols. Results obtained from this research show the relationship between dust concentrations and meteorological parameters. Dust concentrations are highly correlated with relative humidity and wind speed. With all the data collected on site and the analysis of the meteorological parameters, models can be develop to predict the transport of particles as well as the concentration of contaminants at a specific point. These models were developed and are part of the results shown in this dissertation.

Spatial and temporal variability of fine particle composition and source types in five cities of Connecticut and Massachusetts.

PubMed

Lee, Hyung Joo; Gent, Janneane F; Leaderer, Brian P; Koutrakis, Petros

2011-05-01

To protect public health from PM(2.5) air pollution, it is critical to identify the source types of PM(2.5) mass and chemical components associated with higher risks of adverse health outcomes. Source apportionment modeling using Positive Matrix Factorization (PMF), was used to identify PM(2.5) source types and quantify the source contributions to PM(2.5) in five cities of Connecticut and Massachusetts. Spatial and temporal variability of PM(2.5) mass, components and source contributions were investigated. PMF analysis identified five source types: regional pollution as traced by sulfur, motor vehicle, road dust, oil combustion and sea salt. The sulfur-related regional pollution and traffic source type were major contributors to PM(2.5). Due to sparse ground-level PM(2.5) monitoring sites, current epidemiological studies are susceptible to exposure measurement errors. The higher correlations in concentrations and source contributions between different locations suggest less spatial variability, resulting in less exposure measurement errors. When concentrations and/or contributions were compared to regional averages, correlations were generally higher than between-site correlations. This suggests that for assigning exposures for health effects studies, using regional average concentrations or contributions from several PM(2.5) monitors is more reliable than using data from the nearest central monitor. Copyright © 2011 Elsevier B.V. All rights reserved.

Source Identification and Apportionment of Trace Elements in Soils in the Yangtze River Delta, China.

PubMed

Shao, Shuai; Hu, Bifeng; Fu, Zhiyi; Wang, Jiayu; Lou, Ge; Zhou, Yue; Jin, Bin; Li, Yan; Shi, Zhou

2018-06-12

Trace elements pollution has attracted a lot of attention worldwide. However, it is difficult to identify and apportion the sources of multiple element pollutants over large areas because of the considerable spatial complexity and variability in the distribution of trace elements in soil. In this study, we collected total of 2051 topsoil (0⁻20 cm) samples, and analyzed the general pollution status of soils from the Yangtze River Delta, Southeast China. We applied principal component analysis (PCA), a finite mixture distribution model (FMDM), and geostatistical tools to identify and quantitatively apportion the sources of seven kinds of trace elements (chromium (Cr), cadmium (Cd), mercury (Hg), copper (Cu), zinc (Zn), nickel (Ni), and arsenic (As)) in soil. The PCA results indicated that the trace elements in soil in the study area were mainly from natural, multi-pollutant and industrial sources. The FMDM also fitted three sub log-normal distributions. The results from the two models were quite similar: Cr, As, and Ni were mainly from natural sources caused by parent material weathering; Cd, Cu, and Zu were mainly from mixed sources, with a considerable portion from anthropogenic activities such as traffic pollutants, domestic garbage, and agricultural inputs, and Hg was mainly from industrial wastes and pollutants.

76 FR 2765 - Apportionments to Dependents and Payments to Fiduciaries and Incarcerated Beneficiaries

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-14

... Eligibility for apportionment of a surviving spouse's dependency and indemnity compensation. 5.782 Effective... Limitation on dependency and indemnity compensation during incarceration. 5.813 Discontinuance of pension... disability compensation or dependency and indemnity compensation upon a beneficiary's release from...

Source apportionment of polycyclic aromatic hydrocarbons in Louisiana

NASA Astrophysics Data System (ADS)

Han, F.; Zhang, H.

2017-12-01

Polycyclic aromatic hydrocarbons (PAHs) in the environment are of significant concern due to their high toxicity that may result in adverse health effects. PAHs measurements at the limited air quality monitoring stations alone are insufficient to gain a complete concept of ambient PAH levels. This study simulates the concentrations of PAHs in Louisiana and identifies the major emission sources. Speciation profiles for PAHs were prepared using data assembled from existing emission profile databases. The Sparse Matrix Operator Kernel Emission (SMOKE) model was used to generate the estimated gridded emissions of 16 priority PAH species directly associated with health risks. The estimated emissions were then applied to simulate ambient concentrations of PAHs in Louisiana for January, April, July and October 2011 using the Community Multiscale Air Quality (CMAQ) model (v5.0.1). Through the formation, transport and deposition of PAHs species, the concentrations of PAHs species in gas phase and particulate phase were obtained. The spatial and temporal variations were analyzed and contributions of both local and regional major sources were quantified. This study provides important information for the prevention and treatment of PAHs in Louisiana.

[Quantitative estimation source of urban atmospheric CO2 by carbon isotope composition].

PubMed

Liu, Wei; Wei, Nan-Nan; Wang, Guang-Hua; Yao, Jian; Zeng, You-Shi; Fan, Xue-Bo; Geng, Yan-Hong; Li, Yan

2012-04-01

To effectively reduce urban carbon emissions and verify the effectiveness of currently project for urban carbon emission reduction, quantitative estimation sources of urban atmospheric CO2 correctly is necessary. Since little fractionation of carbon isotope exists in the transportation from pollution sources to the receptor, the carbon isotope composition can be used for source apportionment. In the present study, a method was established to quantitatively estimate the source of urban atmospheric CO2 by the carbon isotope composition. Both diurnal and height variations of concentrations of CO2 derived from biomass, vehicle exhaust and coal burning were further determined for atmospheric CO2 in Jiading district of Shanghai. Biomass-derived CO2 accounts for the largest portion of atmospheric CO2. The concentrations of CO2 derived from the coal burning are larger in the night-time (00:00, 04:00 and 20:00) than in the daytime (08:00, 12:00 and 16:00), and increase with the increase of height. Those derived from the vehicle exhaust decrease with the height increase. The diurnal and height variations of sources reflect the emission and transport characteristics of atmospheric CO2 in Jiading district of Shanghai.

Source apportionment of carbonaceous aerosols in a megacity of northwest China: insights from radiocarbon measurement

NASA Astrophysics Data System (ADS)

Ni, Haiyan; Huang, Rujin; Dusek, Ulrike

2017-04-01

Fine particulate matter (PM2.5) samples were collected from 5 July 2008 to 27 June 2009 at Xi'an, a very polluted megacity in Northwest China. The 24 h averaged PM2.5concentrations (ranged from 32 μg m-3 to 339 μg m-3) were 1-14 times higher than the WHO guideline for 24 h PM2.5(25 μg m-3). In this work, we unambiguously quantify fossil (e.g., vehicle emissions, coal burning etc.) and non-fossil (e.g., biomass burning, cooking, biogenic emissions etc.) contributions to organic carbon (OC) and elemental carbon (EC) of PM2.5using radiocarbon (14C) measurement. In addition, we measured PM2.5 major components and source markers, including OC and EC, ions, trace elements, polycyclic aromatic hydrocarbons (PAHs), oxygenated PAHs (o-PAHs), anhydrous sugars and hopanes. The preliminary results of radiocarbon measurements in OC and EC show that the annual mean contributions from fossil-fuel combustion to EC was 76 ± 8% (6 ± 2 μg m-3). The remaining 24 ± 8% (2 ± 1 μg m-3) was attributed to biomass burning, with higher contribution in the cold period (˜33%) compared to the warm period (˜21%), due to enhanced emissions from local biomass burning activities in winter. In contrast with EC, OC was dominated by non-fossil sources, with an annual average of 54 ± 8 % (13 ± 10 μg m-3). Clear seasonal variations were seen in OC concentrations both from fossil fuel (OCff), and from non-fossil sources (OCnf), with maxima in the cold period and minima in the warm period, because of enhanced fossil and non-fossil activities in winter, mainly biomass burning and domestic coal burning. Further source apportionment of OC, including primary/secondary fossil OC, primary/secondary non-fossil OC, will be conducted by combining 14C results with positive matrix factorization (PMF) analysis of organic matter (OM).

Open air mineral treatment operations and ambient air quality: assessment and source apportionment.

PubMed

Escudero, M; Alastuey, A; Moreno, T; Querol, X; Pérez, P

2012-11-01

We present a methodology for evaluating and quantifying the impact of inhalable mineral dust resuspension close to a potentially important industrial point source, in this case an open air plant producing sand, flux and kaolin in the Capuchinos district of Alcañiz (Teruel, NE Spain). PM(10) levels at Capuchinos were initially high (42 μg m(-3) as the annual average with 91 exceedances of the EU daily limit value during 2007) but subsequently decreased (26 μg m(-3) with 16 exceedances in 2010) due to a reduced demand for minerals from the ceramic industry and construction sector during the first stages of the economic crisis. Back trajectory and local wind pattern analyses revealed only limited contribution from exotic PM sources such as African dust intrusions whereas there was clearly a strong link with the mineral stockpiles of the local industry. This link was reinforced by chemical and mineral speciation and source apportionment analysis which showed a dominance of mineral matter (sum of CO(3)(2-), SiO(2), Al(2)O(3), Ca, Fe, K, Mg, P, and Ti: mostly aluminosilicates) which in 2007 contributed 76% of the PM(10) mass (44 μg m(-3) on average). The contribution from Secondary Inorganic Aerosols (SIA, sum of SO(4)(2-), NO(3)(-) and NH(4)(+)) reached 8.4 μg m(-3), accounting for 14% of the PM(10) mass, similar to the amount of calcareous road dust estimated to be present (8 μg m(-3); 13%). Organic matter and elemental carbon contributed 5.3 μg m(-3) (9%) whereas marine aerosol (Na + Cl) levels were minor with an average concentration of 0.4 μg m(-3) (1% of the PM(10) mass). Finally, chemical and mineralogical analysis of stockpile samples and comparison with filter samples confirmed the local industry to be the major source of ambient PM(10) in the area.

Improving source identification of Atlanta aerosol using temperature resolved carbon fractions in positive matrix factorization

NASA Astrophysics Data System (ADS)

Kim, Eugene; Hopke, Philip K.; Edgerton, Eric S.

Daily integrated PM 2.5 (particulate matter ⩽2.5 μm in aerodynamic diameter) composition data including eight individual carbon fractions collected at the Jefferson Street monitoring site in Atlanta were analyzed with positive matrix factorization (PMF). Particulate carbon was analyzed using the thermal optical reflectance method that divides carbon into four organic carbon (OC), pyrolized organic carbon (OP), and three elemental carbon (EC) fractions. A total of 529 samples and 28 variables were measured between August 1998 and August 2000. PMF identified 11 sources in this study: sulfate-rich secondary aerosol I (50%), on-road diesel emissions (11%), nitrate-rich secondary aerosol (9%), wood smoke (7%), gasoline vehicle (6%), sulfate-rich secondary aerosol II (6%), metal processing (3%), airborne soil (3%), railroad traffic (3%), cement kiln/carbon-rich (2%), and bus maintenance facility/highway traffic (2%). Differences from previous studies using only the traditional OC and EC data (J. Air Waste Manag. Assoc. 53(2003a)731; Atmos Environ. (2003b)) include four traffic-related combustion sources (gasoline vehicle, on-road diesel, railroad, and bus maintenance facility) containing carbon fractions whose abundances were different between the various sources. This study indicates that the temperature resolved fractional carbon data can be utilized to enhance source apportionment study, especially with respect to the separation of diesel emissions from gasoline vehicle sources. Conditional probability functions using surface wind data and identified source contributions aid the identifications of local point sources.

Identification and elucidation of anthropogenic source contribution in PM10 pollutant: Insight gain from dispersion and receptor models.

PubMed

Roy, Debananda; Singh, Gurdeep; Yadav, Pankaj

2016-10-01

Source apportionment study of PM 10 (Particulate Matter) in a critically polluted area of Jharia coalfield, India has been carried out using Dispersion model, Principle Component Analysis (PCA) and Chemical Mass Balance (CMB) techniques. Dispersion model Atmospheric Dispersion Model (AERMOD) was introduced to simplify the complexity of sources in Jharia coalfield. PCA and CMB analysis indicates that monitoring stations near the mining area were mainly affected by the emission from open coal mining and its associated activities such as coal transportation, loading and unloading of coal. Mine fire emission also contributed a considerable amount of particulate matters in monitoring stations. Locations in the city area were mostly affected by vehicular, Liquid Petroleum Gas (LPG) & Diesel Generator (DG) set emissions, residential, and commercial activities. The experimental data sampling and their analysis could aid understanding how dispersion based model technique along with receptor model based concept can be strategically used for quantitative analysis of Natural and Anthropogenic sources of PM 10 . Copyright © 2016. Published by Elsevier B.V.

Concentration, distribution and source apportionment of atmospheric polycyclic aromatic hydrocarbons in the southeast suburb of Beijing, China.

PubMed

Zhang, Shucai; Zhang, Wei; Wang, Kaiyan; Shen, Yating; Hu, Lianwu; Wang, Xuejun

2009-04-01

Total suspended particle samples and gas phase samples were collected at three representative sampling sites in the southeastern suburb of Beijing from March 2005 to January 2006. The samples were analyzed for 16 US EPA priority PAHs using GC/MS. Concentrations of Sigma PAHs in particle and gas phases were 0.21-1.18 x 10(3) ng m(-3) and 9.5 x 10(2) ng-1.03 x 10(5) ng m(-3), respectively. PAH concentrations displayed seasonal variation in the order of winter>spring>autumn>summer for particle phase, and winter>autumn>summer>spring for gas phase. Partial correlation analysis indicates that PAH concentrations in particle phase are negatively correlated with temperature and positively correlated with air pollution index of SO(2). No significant correlation is observed between gas phase PAHs and the auxiliary parameters. Sources of PAH are identified through principal component analysis, and source contributions are estimated through multiple linear regression. Major sources of atmospheric PAHs in the study area include coal combustion, coke industry, vehicular emission and natural gas combustion.

Emission characteristics and chemical components of size-segregated particulate matter in iron and steel industry

NASA Astrophysics Data System (ADS)

Jia, Jia; Cheng, Shuiyuan; Yao, Sen; Xu, Tiebing; Zhang, Tingting; Ma, Yuetao; Wang, Hongliang; Duan, Wenjiao

2018-06-01

As one of the highest energy consumption and pollution industries, the iron and steel industry is regarded as a most important source of particulate matter emission. In this study, chemical components of size-segregated particulate matters (PM) emitted from different manufacturing units in iron and steel industry were sampled by a comprehensive sampling system. Results showed that the average particle mass concentration was highest in sintering process, followed by puddling, steelmaking and then rolling processes. PM samples were divided into eight size fractions for testing the chemical components, SO42- and NH4+ distributed more into fine particles while most of the Ca2+ was concentrated in coarse particles, the size distribution of mineral elements depended on the raw materials applied. Moreover, local database with PM chemical source profiles of iron and steel industry were built and applied in CMAQ modeling for simulating SO42- and NO3- concentration, results showed that the accuracy of model simulation improved with local chemical source profiles compared to the SPECIATE database. The results gained from this study are expected to be helpful to understand the components of PM in iron and steel industry and contribute to the source apportionment researches.

75 FR 33384 - Proposed Collection; Comment Request for Regulation Project

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-11

... 8228; TD 8410), Allocation and Apportionment of Interest Expense and Certain Other Expenses (Sec. Sec... to be assured of consideration. ADDRESSES: Direct all written comments to Gerald J. Shields, Internal...: Allocation and Apportionment of Interest Expense and Certain Other Expenses. OMB Number: 1545-1072...

Source Apportionment of Atmospheric Particles by Electron Probe X-Ray Microanalysis and Receptor Models.

NASA Astrophysics Data System (ADS)

van Borm, Werner August

Electron probe X-ray microanalysis (EPXMA) in combination with an automation system and an energy-dispersive X-ray detection system was used to analyse thousands of microscopical particles, originating from the ambient atmosphere. The huge amount of data was processed by a newly developed X-ray correction method and a number of data reduction procedures. A standardless ZAF procedure for EPXMA was developed for quick semi-quantitative analysis of particles starting from simple corrections, valid for bulk samples and modified taking into account the particle finit diameter, assuming a spherical shape. Tested on a limited database of bulk and particulate samples, the compromise between calculation speed and accuracy yielded for elements with Z > 14 accuracies on concentrations less than 10% while absolute deviations remained below 4 weight%, thus being only important for low concentrations. Next, the possibilities for the use of supervised and unsupervised multivariate particle classification were investigated for source apportionment of individual particles. In a detailed study of the unsupervised cluster analysis technique several aspects were considered, that have a severe influence on the final cluster analysis results, i.e. data acquisition, X-ray peak identification, data normalization, scaling, variable selection, similarity measure, cluster strategy, cluster significance and error propagation. A supervised approach was developed using an expert system-like approach in which identification rules are builded to describe the particle classes in a unique manner. Applications are presented for particles sampled (1) near a zinc smelter (Vieille-Montagne, Balen, Belgium), analyzed for heavy metals, (2) in an urban aerosol (Antwerp, Belgium), analyzed for over 20 elements and (3) in a rural aerosol originating from a swiss mountain area (Bern). Thus is was possible to pinpoint a number of known and unknown sources and characterize their emissions in terms of particles abundance and particle composition. Alternatively, the bulk analysis of filters (total, fine and coarse mode) using Particle Induced X -Ray Emission (PIXE) and the application of a receptor modeling approach provided for complementary information on a macroscopical level. A computer program was developed incorporating an absolute factor analysis based receptor modeling procedure. Source profiles and contributions are described by elemental concentrations and an atmospheric mass balance is put forward. The latter method was applied in a two year study of the Antwerp urban aerosol and for the swiss aerosol, revealing a number of previously known and unknown sources. Both methods were successfully combined to increase the source resolution.

Trends and sources for heavy metals in urban atmosphere

NASA Astrophysics Data System (ADS)

Kemp, Kåre

2002-04-01

The concentrations of a number of heavy metals in the air in three Danish cities have been measured by means of PIXE for more than two decades. The well-known capability of PIXE for fast and efficient analysis of aerosol samples has been employed for analysis of daily samples from several sites during the whole period. The main sources are traffic, domestic heating and long-range transport. Source apportionment and trends for single metals are assessed by means of simple statistical methods. The most striking change has occurred for the Pb concentration, which is reduced by almost a factor of 100 following the reduction of the Pb content in petrol. The main source of Cu, Cr and Zn is the traffic. The concentrations of these elements have been slightly increasing. The concentrations for most of the other heavy metals, which originate mainly from sources outside the cities, have been decreasing.

Monitoring and source apportionment of trace elements in PM2.5: Implications for local air quality management.

PubMed

Li, Yueyan; Chang, Miao; Ding, Shanshan; Wang, Shiwen; Ni, Dun; Hu, Hongtao

2017-07-01

Fine particulate matter (PM 2.5 ) samples were collected simultaneously every hour in Beijing between April 2014 and April 2015 at five sites. Thirteen trace elements (TEs) in PM 2.5 were analyzed by online X-ray fluorescence (XRF). The annual average PM 2.5 concentrations ranged from 76.8 to 102.7 μg m -3 . TEs accounted for 5.9%-8.7% of the total PM 2.5 mass with Cl, S, K, and Si as the most dominant elements. Spearman correlation coefficients of PM 2.5 or TE concentrations between the background site and other sites showed that PM 2.5 and some element loadings were affected by regional and local sources, whereas Cr, Si, and Ni were attributed to substantial local emissions. Temporal variations of TEs in PM 2.5 were significant and provided information on source profiles. The PM 2.5 concentrations were highest in autumn and lowest in summer. Mn and Cr showed similar variation. Fe, Ca, Si, and Ti tended to show higher concentrations in spring, whereas concentrations of S peaked in summer. Concentrations of Cl, K, Pb, Zn, Cu, and Ni peaked in winter. PM 2.5 and TE median concentrations were higher on Saturdays than on weekdays. The diurnal pattern of PM 2.5 and TE median concentrations yielded similar bimodal patterns. Five dominant sources of PM 2.5 mass were identified via positive matrix factorization (PMF). These sources included the regional and local secondary aerosols, traffic, coal burning, soil dust, and metal processing. Air quality management strategies, including regional environmental coordination and collaboration, reduction in secondary aerosol precursors, restrictive vehicle emission standards, promotion of public transport, and adoption of clean energy, should be strictly implemented. High time-resolution measurements of TEs provided detailed source profiles, which can greatly improve precision in interpreting source apportionment calculations; the PMF analysis of online XRF data is a powerful tool for local air quality management. Copyright © 2017 Elsevier Ltd. All rights reserved.

42 CFR 413.50 - Apportionment of allowable costs.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Apportionment of allowable costs. (a) Consistent with prevailing practice in which third-party organizations pay... participate in the program. Available evidence shows that the use of services by persons age 65 and over... time by third-party purchasers of inpatient hospital care apportions a provider's total costs among...

14 CFR 1215.104 - Apportionment and assignment of services.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 5 2010-01-01 2010-01-01 false Apportionment and assignment of services. 1215.104 Section 1215.104 Aeronautics and Space NATIONAL AERONAUTICS AND SPACE ADMINISTRATION TRACKING AND DATA RELAY SATELLITE SYSTEM (TDRSS) Use and Reimbursement Policy for Non-U.S. Government Users...

14 CFR 1215.104 - Apportionment and assignment of services.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 5 2011-01-01 2010-01-01 true Apportionment and assignment of services. 1215.104 Section 1215.104 Aeronautics and Space NATIONAL AERONAUTICS AND SPACE ADMINISTRATION TRACKING AND DATA RELAY SATELLITE SYSTEM (TDRSS) Use and Reimbursement Policy for Non-U.S. Government Users...

75 FR 13208 - Proposed Collection; Comment Request for Revenue Procedure 2006-42

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-18

... to the Apportionment of Interest Expense, Research and Experimental Expenditures Under Section 1.861... Certain Elections Relating to the Apportionment of Interest Expense, Research and Experimental... automatic consent to change (a) from the fair market value method or from the alternative tax book method to...

77 FR 2240 - Allocation and Apportionment of Interest Expense

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-17

... allocation and apportionment of interest expense using the fair market value asset method. The temporary... law by the legislation commonly referred to as the Education Jobs and Medicaid Assistance Act (EJMAA... using the fair market value method. The text of those regulations also serves as the text of these...

38 CFR 13.70 - Apportionment of benefits to dependents.

Code of Federal Regulations, 2010 CFR

2010-07-01

... veteran's spouse, child or dependent parent as may be necessary to provide for their needs. (b) Dependent... a dependent parent or parents and the fiduciary neglects or refuses to make an equivalent... apportionment to the veteran's spouse, child or dependent parent of any benefit not paid under an institutional...

78 FR 16916 - Proposed Collection; Comment Request for Regulation Project

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-19

... allocation and apportionment of deduction for state income. DATES: Written comments should be received on or before May 20, 2013 to be assured of consideration. ADDRESSES: Direct all written comments to Yvette... INFORMATION: Title: Allocation and Apportionment of Deduction for State Income Taxes. OMB Number: 1545-1224...

Concentration profiles, source apportionment and risk assessment of polycyclic aromatic hydrocarbons (PAHs) in dumpsite soils from Agbogbloshie e-waste dismantling site, Accra, Ghana.

PubMed

Daso, Adegbenro P; Akortia, Eric; Okonkwo, Jonathan O

2016-06-01

The concentrations of eighteen (18) polycyclic aromatic hydrocarbons (PAHs), including the 16 USEPA's priority PAHs as well as two alkyl-substituted naphthalenes were determined in dumpsite soils collected from different sampling sites within the Agbogbloshie e-waste dismantling site in Accra, Ghana. Following their isolation with ultrasonic-assisted extraction technique, the concentrations of the PAHs were determined by gas chromatography mass spectrometry (GC-MS). Loss-on-ignition (LOI) method was employed for the determination of total organic carbon (TOC) of the soil samples. The mean Σ18PAHs obtained were 3006, 5627, 3046, 5555, and 7199 ng g(-1) dry weight (dw) for sampling sites A (mosque), B (dismantling site), C (residential house/police station), D (personal computer repairers' shop) and E (e-waste open burning area), respectively. In all cases, the prevalence of phenanthrene, fluoranthene and pyrene was generally observed across the sampling sites. In this study, PAHs with two to three rings and four to six rings exhibited strong positive correlations, whereas BbF and BkF showed weak positive and negative correlations with other PAHs investigated. With the exception of BbF and BkF, all the PAHs had moderate to strong positive correlations with the TOC. Benzo[a]pyrene equivalent (BaPeq) concentration is a useful indicator of the carcinogenic potency of environmental matrices and these ranged between 111 and 454 ng g(-1), which are generally below the 'safe' level of 600 ng g(-1) established for the protection of the environment and human health. Interestingly, the seven carcinogenic PAHs were the major contributors to the BaPeq concentrations accounting between 97.7 and 98.3 %. Despite the minimal risk to cancer via exposure to the investigated dumpsite soil as indicated in the present study, the prolonged exposure to these pollutants via various exposure pathways may result in increased risk to cancer over time. The application of several methodological approaches for PAH source apportionment, including the use of molecular diagnostic ratios, mostly implicated pyrogenic processes as the main sources of PAHs into the investigated dumpsite soils. Furthermore, their compositional profiles across the sampling sites also suggest similar sources of PAHs into the dumpsite soil.

Appraisement, source apportionment and health risk of polycyclic aromatic hydrocarbons (PAHs) in vehicle-wash wastewater, Pakistan.

PubMed

Qamar, Zahir; Khan, Sardar; Khan, Anwarzeb; Aamir, Muhammad; Nawab, Javed; Waqas, Muhammad

2017-12-15

Vehicle-wash wastewater (VWW) contains elevated concentrations of different petrochemicals including polycyclic aromatic hydrocarbons (PAHs), a carcinogenic group of organic compounds. This study investigates the discharge of PAHs present in the untreated wastewater of vehicle-wash stations (VWS) located in district Peshawar, Pakistan. The data obtained was being novel with the detection of 16 USEPA PAHs (both individuals and total) and compared with earlier studies and international standards. The ∑16PAHs in wastewater from light vehicle-wash stations (LVWS) and heavy vehicle-wash stations (HVWS) ranged from 245-429μg/l and 957-1582μg/l, respectively. A significant difference (p<0.01) was observed in PAHs discharged from LVWS and HVWS. The projected ∑16PAHs discharge from both HVWS (92% of total generated PAHs) and LVWS (8%) was about 5109.9 g per annum. According to PAH diagnostic ratios, PAHs were both petrogenic (chrysene/benz(a)anthracene, low molecular weight/high molecular weight) and pyrogenic (phenanthrene/anthracene, fluoranthene/pyrene, fluoranthene/fluoranthene+pyrene) in origin. The highest toxic equivalent quotient (TEQ) value was shown by benzo(a)pyrene (21.6μg/l) followed by dibenz(ah)anthracene (9.81μg/l) in wastewater from HVWS. However, in LVWS the case was reversed with highest value (7.54μg/l) for dibenz(ah)anthracene followed by benzo(a)pyrene (3.54μg/l). The lowest TEQ value was indicated for phenanthrene (0.007μg/l) in wastewater of LVWS, while pyrene showed the lowest value (0.007μg/l) in wastewater of HVWS. The results indicated that VWS contribute significant amount of PAHs each year, which is of great concern regarding water quality, ecological and human health risk. This is the first systematic and comprehensive research related with generation of PAHs load per day, week, month and annum from VWS, their source apportionment and health effects in Pakistan. Copyright © 2017 Elsevier B.V. All rights reserved.

Source apportionment of elevated wintertime PAHs by compound-specific radiocarbon analysis

NASA Astrophysics Data System (ADS)

Sheesley, R. J.; Kruså, M.; Krecl, P.; Johansson, C.; Gustafsson, Ã.-.

2008-12-01

Natural abundance radiocarbon analysis facilitates distinct source apportionment between contemporary biomass/biofuel (14C "alive") versus fossil fuel (14C "dead") combustion. Here, the first compound-specific radiocarbon analysis (CSRA) of atmospheric polycylic aromatic hydrocarbons (PAHs) was demonstrated for a set of samples collected in Lycksele, Sweden a small town with frequent episodes of severe atmospheric pollution in the winter. Renewed interest in residential wood combustion means than this type of seasonal pollution is of increasing concern in many areas. Five individual/paired PAH isolates from three pooled fortnight-long filter collections were analyzed by CSRA: phenanthrene, fluoranthene, pyrene, benzo[b+k]fluoranthene and indeno[cd]pyrene plus benzo[ghi]perylene; phenanthrene was the only compound also analyzed in the gas phase. The measured Δ14C for PAHs spanned from -138.3‰ to 58.0‰. A simple isotopic mass balance model was applied to estimate the fraction biomass (fbiomass) contribution that was constrained to a range of 71% for indeno[cd]pyrene+benzo[ghi]perylene to 87% for the gas phase phenanthrene and particulate fluoranthene, respectively. Indeno[cd]pyrene plus benzo[ghi]perylene, known to be enhanced in gasoline-powered motor vehicle exhaust compared to diesel exhaust, had the lowest contribution of biomass combustion of the measured PAHs by 9%. The total organic carbon (TOC, defined as carbon remaining after removal of inorganic carbon) fbiomass was estimated to be 77%, which falls within the range for PAHs. This CSRA data of atmospheric PAHs demonstrate the non-uniformity of biomass combustion contribution to different PAHs even in a location with limited local emission sources and illustrates that regulatory efforts would not evenly reduce all PAHs.

Successful application of lead isotopes in source apportionment, legal proceedings, remediation and monitoring.

PubMed

Gulson, Brian; Korsch, Michael; Winchester, Wayne; Devenish, Matthew; Hobbs, Thad; Main, Cleve; Smith, Gerard; Rosman, Kevin; Howearth, Lynette; Burn-Nunes, Laurie; Seow, Jimmy; Oxford, Cameron; Yun, Gracie; Gillam, Lindsay; Crisp, Michelle

2012-01-01

In late 2006, the seaside community in Esperance Western Australia was alerted to thousands of native bird species dying. The source of the lead (Pb) was determined by Pb isotopes to derive from the handling of Pb carbonate concentrate through the Port, which began in July 2005. Concern was expressed for the impact of this on the community. Our objectives were to employ Pb isotope ratios to evaluate the source of Pb in environmental samples for use in legal proceedings, and for use in remediation and monitoring. Isotope measurements were undertaken of bird livers, plants, drinking water, soil, harbour sediments, air, bulk ceiling dust, gutter sludge, surface swabs and blood. The unique lead isotopic signature of the contaminating Pb carbonate enabled diagnostic apportionment of lead in samples. Apart from some soil and water samples, the proportion of contaminating Pb was >95% in the environmental samples. Lead isotopes were critical in resolving legal proceedings, are being used in the remediation of premises, were used in monitoring of workers involved in the decontamination of the storage facility, and monitoring transport of the concentrate through another port facility. Air samples show the continued presence of contaminant Pb, more than one year after shipping of concentrate ceased, probably arising from dust resuspension. Brief details of the comprehensive testing and cleanup of the Esperance community are provided along with the role of the Community. Lead isotopic analyses can provide significant benefits to regulatory agencies, interested parties, and the community where the signature is able to be characterised with a high degree of certainty. Crown Copyright © 2011. Published by Elsevier Inc. All rights reserved.

Source apportionment by PMF on elemental concentrations obtained by PIXE analysis of PM10 samples collected at the vicinity of lignite power plants and mines in Megalopolis, Greece

NASA Astrophysics Data System (ADS)

Manousakas, M.; Diapouli, E.; Papaefthymiou, H.; Migliori, A.; Karydas, A. G.; Padilla-Alvarez, R.; Bogovac, M.; Kaiser, R. B.; Jaksic, M.; Bogdanovic-Radovic, I.; Eleftheriadis, K.

2015-04-01

Particulate matter (PM) is an important constituent of atmospheric pollution especially in areas under the influence of industrial emissions. Megalopolis is a small city of 10,000 inhabitants located in central Peloponnese in close proximity to three coal opencast mines and two lignite fired power plants. 50 PM10 samples were collected in Megalopolis during the years 2009-11 for elemental and multivariate analysis. For the elemental analysis PIXE was used as one of the most effective techniques in APM analytical characterization. Altogether, the concentrations of 22 elements (Z = 11-33), whereas Black Carbon was also determined for each sample using a reflectometer. Factorization software was used (EPA PMF 3.0) for source apportionment analysis. The analysis revealed that major emission sources were soil dust 33% (7.94 ± 0.27 μg/m3), biomass burning 19% (4.43 ± 0.27 μg/m3), road dust 15% (3.63 ± 0.37 μg/m3), power plant emissions 13% (3.01 ± 0.44 μg/m3), traffic 12% (2.82 ± 0.37 μg/m3), and sea spray 8% (1.99 ± 0.41 μg/m3). Wind trajectories have suggested that metals associated with emission from the power plants came mainly from west and were connected with the locations of the lignite mines located in this area. Soil resuspension, road dust and power plant emissions increased during the warm season of the year, while traffic/secondary, sea spray and biomass burning become dominant during the cold season.