76 FR 46715 - Proposed Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-03

... table provided here represents the flooding sources, location of referenced elevations, effective and.... Specifically, it addresses the following flooding sources: Cabin Branch, Franklin Branch, Hall Creek, Little... Incorporated Areas'' addressed the following flooding sources: Cabin Branch, Franklin Branch, Little Patuxent...

76 FR 26981 - Proposed Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-10

... table provided here represents the flooding sources, location of referenced elevations, effective and.... Specifically, it addresses the following flooding sources: Cache Creek, Cache Creek Left Bank Overflow, and... ``Unincorporated Areas of Yolo County, California'' addressed the flooding source Cache Creek Settling Basin. That...

76 FR 13570 - Proposed Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-14

.... The table provided here represents the flooding sources, location of referenced elevations, effective.... Specifically, it addresses the flooding source South Creek. DATES: Comments are to be submitted on or before... table, entitled ``Sanpete County, Utah, and Incorporated Areas'' addressed the flooding source South...

Determination of instream metal loads using tracer-injection and synoptic-sampling techniques, Wightman Fork, southwestern Colorado, July 1999

USGS Publications Warehouse

Ortiz, Roderick F.

2001-01-01

In July 1999, a tracer-injection study was conducted concurrently with synoptic sampling to generate mass-load profiles in Wightman Fork near the Summitville Mine site. The mine site is located in the San Juan Mountains of southwestern Colorado at an elevation of about 3,500 meters above sea level. Metal loads increased substantially along the 2,815-meter study reach along the boundary of the mine site. Spatial determinations of dissolved aluminum, copper, iron, manganese, and zinc loads were used to identify potential source areas to the stream. Overall, four source areas appeared to contribute most of the specific load at the end of the study reach. One source area was along a 60-meter reach downgradient from the toe of the North Waste Dump that generally corresponded to a region of radial faults. Another source area was a short reach that included inputs from the Summitville Water Treatment Facility and the Pump House Fault. In July 1999, seepage from the Summitville Dam Impoundment was a substantial contributor of metal load at the end of the study reach. Finally, the metal load contributed along a 60-meter reach that included Cropsy Creek is considered a substantial source of metal load to Wightman Fork.

77 FR 11974 - Approval and Promulgation of Implementation Plans; State of Iowa Regional Haze State...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-28

... and beyond. The modeling was based on PM Source Apportionment Technology (PSAT) for the Comprehensive... sources and the State adequately determined the apportionment of those pollutants from sources located... Class I areas caused by emissions of air pollutants from numerous sources located over a wide geographic...

78 FR 22221 - Proposed Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-15

... table provided here represents the flooding sources, location of referenced elevations, effective and.... Specifically, it addresses the following flooding sources: Pea Branch and Reedy Branch. DATES: Comments are to... Areas'' did not address the flooding sources Pea Branch and Reedy Branch. That table omitted information...

77 FR 51744 - Proposed Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-27

..., FEMA published in the Federal Register a proposed rule that included an erroneous flooding source name for the Town of Livonia in Pointe Coupee Parish, Louisiana. The flooding source name of Bayou Fordoche... Coupee Parish, Louisiana, and Incorporated Areas'' addressed several flooding sources, including Bayou...

77 FR 51745 - Proposed Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-27

.... Specifically, it addresses the following flooding sources: Back Creek, Big Elk Creek, Bohemia River, Chesapeake... Areas'' addressed the following flooding sources: Back Creek, Big Elk Creek, Bohemia River, Chesapeake... modified elevation in feet, and/or communities affected for the following flooding sources: Big Elk Creek...

Development of unauthorized airborne emission source identification procedure

NASA Astrophysics Data System (ADS)

Shtripling, L. O.; Bazhenov, V. V.; Varakina, N. S.; Kupriyanova, N. P.

2018-01-01

The paper presents the procedure for searching sources of unauthorized airborne emissions. To make reasonable regulation decisions on airborne pollutant emissions and to ensure the environmental safety of population, the procedure provides for the determination of a pollutant mass emission value from the source being the cause of high pollution level and the search of a previously unrecognized contamination source in a specified area. To determine the true value of mass emission from the source, the minimum of the mean-root-square mismatch criterion between the computed and measured pollutant concentration in the given location is used.

Trees, chemistry, and prehistory in the American Southwest

USGS Publications Warehouse

Durand, S.R.; Shelley, P.H.; Antweiler, Ronald C.; Taylor, Howard E.

1999-01-01

At least 200 000 trees were used in the building construction in Chaco Canyon, New Mexico, from about (AD) 850-1150. A large portion of these construction timbers were transported 50 km or more and the harvesting location(s) is not known. We argue that a feasible method for determining the wood source areas is to chemically characterize the possible source areas using modern wood and then attempt to match the prehistoric timbers to the modern signatures. This paper establishes the feasibility of this method. ICP-AES was employed to obtain element concentration values for 29 elements, from 62 trees, on three bedrock types. We conclude that it is possible to isolate the variation due to lithology if one controls for wood type (bark, sapwood, heartwood). In addition, ICP-MS was used for the analysis of a small sample of ancient wood. Data from these determinations are presented and the results indicate that the elemental variation is consistent with the most current model of wood use practices in Chaco Canyon. The methods pioneered here should be broadly applicable for determining wood source areas.

Potential sources of bacteriological pollution for two bays with marinas in Trinidad.

PubMed

Bullock, Christine Ann; Moonesar, Indar

2005-05-01

Welcome Bay and Chaguaramas Bay in the northwest peninsula of Trinidad contain large marinas and smaller sections of bathing beaches. Bacteriological surveys were conducted at both bays to assess water quality and to determine potential sources of pollution. These surveys were conducted during the wet season of 1996 and the dry season of 1997. Eleven sample stations were established at Welcome Bay and 12 at Chaguaramas Bay. Freshwater samples were collected from rivers and drains within the survey area. Marine water samples were collected from marinas, bathing beaches and inshore and outer areas at both bays. Five water samples were collected from each sampling station during the wet season of 1996 and six during the dry season of 1997. The membrane filter technique was used to determine faecal coliform and Escherichia coli levels in all samples. There was a seasonal effect on water quality, with significantly higher faecal coliform levels in the wet season, when water quality was not in compliance with international standards. This represents a potential health risk in bathing areas. Water quality was better at the outer area of both bays. Water quality at the inner bay areas was most likely adversely affected by land-based sources of pollution identified in this study. These sources include three drains and two rivers, which discharged into the bays. Yachts were apparently not a source of sewage pollution: there was no significant relationship between yacht number and faecal coliform levels.

Assessment of well vulnerability for groundwater source protection based on a solute transport model: a case study from Jilin City, northeast China

NASA Astrophysics Data System (ADS)

Huan, Huan; Wang, Jinsheng; Lai, Desheng; Teng, Yanguo; Zhai, Yuanzheng

2015-05-01

Well vulnerability assessment is essential for groundwater source protection. A quantitative approach to assess well vulnerability in a well capture zone is presented, based on forward solute transport modeling. This method was applied to three groundwater source areas (Jiuzhan, Hadawan and Songyuanhada) in Jilin City, northeast China. The ratio of the maximum contaminant concentration at the well to the released concentration at the contamination source ( c max/ c 0) was determined as the well vulnerability indicator. The results indicated that well vulnerability was higher close to the pumping well. The well vulnerability in each groundwater source area was low. Compared with the other two source areas, the cone of depression at Jiuzhan resulted in higher spatial variability of c max/ c 0 and lower minimum c max/ c 0 by three orders of magnitude. Furthermore, a sensitivity analysis indicated that the denitrification rate in the aquifer was the most sensitive with respect to well vulnerability. A process to derive a NO3-N concentration at the pumping well is presented, based on determining the maximum nitrate loading limit to satisfy China's drinking-water quality standards. Finally, the advantages, disadvantages and prospects for improving the precision of this well vulnerability assessment approach are discussed.

77 FR 34810 - Determination of Failure To Attain by 2005 and Determination of Current Attainment of the 1-Hour...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-12

... obviates the need for submission of any contingency measures for failure to attain that revoked standard... Baltimore area is no longer obliged to submit and implement the 1-hour ozone contingency measure requirement... 1-hour nonattainment area contingency measures or major source penalty fee programs among the...

Determination of sediment provenance by unmixing the mineralogy of source-area sediments: The "SedUnMix" program

USGS Publications Warehouse

Andrews, John T.; Eberl, D.D.

2012-01-01

Along the margins of areas such as Greenland and Baffin Bay, sediment composition reflects a complex mixture of sources associated with the transport of sediment in sea ice, icebergs, melt-water and turbidite plumes. Similar situations arise in many contexts associated with sediment transport and with the mixing of sediments from different source areas. The question is: can contributions from discrete sediment (bedrock) sources be distinguished in a mixed sediment by using mineralogy, and, if so, how accurately? To solve this problem, four end-member source sediments were mixed in various proportions to form eleven artificial mixtures. Two of the end-member sediments are felsic, and the other two have more mafic compositions. End member and mixed sediment mineralogies were measured for the < 2. mm sediment fractions by quantitative X-ray diffraction (qXRD). The proportions of source sediments in the mixtures then were calculated using an Excel macro program named SedUnMix, and the results were evaluated to determine the robustness of the algorithm. The program permits the unmixing of up to six end members, each of which can be represented by up to 5 alternative compositions, so as to better simulate variability within each source region. The results indicate that we can track the relative percentages of the four end members in the mixtures. We recommend, prior to applying the technique to down-core or to other provenance problems, that a suite of known, artificial mixtures of sediments from probable source areas be prepared, scanned, analyzed for quantitative mineralogy, and then analyzed by SedUnMix to check the sensitivity of the method for each specific unmixing problem. ?? 2011 Elsevier B.V..

[Carbon source metabolic diversity of soil microbial community under different climate types in the area affected by Wenchuan earthquake].

PubMed

Zhang, Guang-Shuai; Lin, Yong-Ming; Ma, Rui-Feng; Deng, Hao-Jun; Du, Kun; Wu, Cheng-Zhen; Hong, Wei

2015-02-01

The MS8.0 Wenchuan earthquake in 2008 led to huge damage to land covers in northwest Sichuan, one of the critical fragile eco-regions in China which can be divided into Semi-arid dry hot climate zone (SDHC) and Subtropical humid monsoon climate zone (SHMC). Using the method of Bilog-ECO-microplate technique, this paper aimed to determine the functional diversity of soil microbial community in the earthquake-affected areas which can be divided into undamaged area (U), recover area (R) and damaged area without recovery (D) under different climate types, in order to provide scientific basis for ecological recovery. The results indicated that the average-well-color-development (AWCD) in undamaged area and recovery area showed SDHC > SHMC, which was contrary to the AWCD in the damaged area without recovery. The AWCD of damaged area without recovery was the lowest in both climate zones. The number of carbon source utilization types of soil microbial in SHMC zone was significantly higher than that in SDHC zone. The carbon source utilization types in both climate zones presented a trend of recover area > undamaged area > damaged area without recovery. The carbon source metabolic diversity characteristic of soil microbial community was significantly different in different climate zones. The diversity index and evenness index both showed a ranking of undamaged area > recover area > damaged area without recovery. In addition, the recovery area had the highest richness index. The soil microbial carbon sources metabolism characteristic was affected by soil nutrient, aboveground vegetation biomass and vegetation coverage to some extent. In conclusion, earthquake and its secondary disasters influenced the carbon source metabolic diversity characteristic of soil microbial community mainly through the change of aboveground vegetation and soil environmental factors.

Spectral Radiance of a Large-Area Integrating Sphere Source

PubMed Central

Walker, James H.; Thompson, Ambler

1995-01-01

The radiance and irradiance calibration of large field-of-view scanning and imaging radiometers for remote sensing and surveillance applications has resulted in the development of novel calibration techniques. One of these techniques is the employment of large-area integrating sphere sources as radiance or irradiance secondary standards. To assist the National Aeronautical and Space Administration’s space based ozone measurement program, a commercially available large-area internally illuminated integrating sphere source’s spectral radiance was characterized in the wavelength region from 230 nm to 400 nm at the National Institute of Standards and Technology. Spectral radiance determinations and spatial mappings of the source indicate that carefully designed large-area integrating sphere sources can be measured with a 1 % to 2 % expanded uncertainty (two standard deviation estimate) in the near ultraviolet with spatial nonuniformities of 0.6 % or smaller across a 20 cm diameter exit aperture. A method is proposed for the calculation of the final radiance uncertainties of the source which includes the field of view of the instrument being calibrated. PMID:29151725

Identifying nitrogen sources to thermal tide pools in Kapoho, Hawai'i, U.S.A, using a multi-stable isotope approach.

PubMed

Wiegner, Tracy N; Mokiao-Lee, Ambyr U; Johnson, Erik E

2016-02-15

Nitrogen (N) enrichment often results in coastal eutrophication, even in remote areas like Hawai'i. Therefore, determining N sources to coastal waters is important for their management. This study identified N sources to tide pools in Kapoho, Hawai'i, and determined their relative importance using three stable isotopes (δ(15)N, δ(18)O, δ(11)B). Surface waters and macroalgal tissues were collected along 100-m onshore-offshore transects in areas of high groundwater input for three months at low tide. Water samples from possible N sources were also collected. Mixing model output, along with macroalgal δ(15)N values, indicated that agriculture soil (34%) was the largest anthropogenic N source followed by sewage (27%). These findings suggest that more effective fertilizer application techniques and upgrading sewage treatment systems can minimize N leaching into groundwater. Overall, our multi-stable isotope approach for identifying N sources was successful and may be useful in other coastal waters. Copyright © 2015 Elsevier Ltd. All rights reserved.

Determination of the rockfall source in an urban settlement area by using a rule-based fuzzy evaluation

NASA Astrophysics Data System (ADS)

Aksoy, H.; Ercanoglu, M.

2006-10-01

The evaluation of the rockfall initiation mechanism and the simulation of the runout behavior is an important issue in the prevention and remedial measures for potential rockfall hazards in highway protection, in forest preservation, and especially in urban settlement areas. In most of the studies in the literature, the extent of the rockfall hazard was determined by various techniques basing on the selection of a rockfall source, generally defined as zones of rock bodies having slope angles higher than a certain value, proposed by general practice. In the present study, it was aimed to carry out a rule-based fuzzy analysis on the discontinuity data of andesites in the city of Ankara, Turkey, in order to bring a different and rather systematic approach to determine the source areas for rockfall hazard in an urban settlement, based on the discontinuity and natural slope features. First, to obtain rock source areas (RSAs), data obtained from the field studies were combined with a rule-based fuzzy evaluation, incorporating the altitude difference, the number of discontinuities, the number of wedges and the number of potential slides as the parameters of the fuzzy sets. After processing the outputs of the rule-based fuzzy system and producing the linguistic definitions, it could be possible to obtain potential RSAs. According to the RSA maps, 1.7% of the study area was found to have "high RSA", and 5.8% of the study area was assigned as "medium RSA". Then, potential rockfall hazard map was prepared. At the final stage, based upon the high and medium RSAs, 3.6% of the study area showed "high rockfall potential", while areal distribution of "medium rockfall potential" was found as 7.9%. Both RSA and potential rockfall hazard map were in accordance with the observations performed in the field.

Isotopic identification of natural vs. anthropogenic lead sources in marine sediments from the inner Ría de Vigo (NW Spain).

PubMed

Álvarez-Iglesias, P; Rubio, B; Millos, J

2012-10-15

San Simón Bay, the inner part of the Ría de Vigo (NW Spain), an area previously identified as highly polluted by Pb, was selected for the application of Pb stable isotope ratios as a fingerprinting tool in subtidal and intertidal sediment cores. Lead isotopic ratios were determined by inductively coupled plasma mass spectrometry on extracts from bulk samples after total acid digestion. Depth-wise profiles of (206)Pb/(207)Pb, (206)Pb/(204)Pb, (207)Pb/(204)Pb, (208)Pb/(204)Pb and (208)Pb/(207)Pb ratios showed, in general, an upward decrease for both intertidal and subtidal sediments as a consequence of the anthropogenic activities over the last century, or centuries. Waste channel samples from a nearby ceramic factory showed characteristic Pb stable isotope ratios different from those typical of coal and petrol. Natural isotope ratios from non-polluted samples were established for the study area, differentiating sediments from granitic or schist-gneiss sources. A binary mixing model employed on the polluted samples allowed estimating the anthropogenic inputs to the bay. These inputs represented between 25 and 98% of Pb inputs in intertidal samples, and 9-84% in subtidal samples, their contributions varying with time. Anthropogenic sources were apportioned according to a three-source model. Coal combustion-related emissions were the main anthropogenic source Pb to the bay (60-70%) before the establishment of the ceramic factory in the area (in the 1970s) which has since constituted the main source (95-100%), followed by petrol-related emissions. The Pb inputs history for the intertidal area was determined for the 20th century, and, for the subtidal area, the 19th and 20th centuries. Copyright © 2012 Elsevier B.V. All rights reserved.

A Direct Position-Determination Approach for Multiple Sources Based on Neural Network Computation.

PubMed

Chen, Xin; Wang, Ding; Yin, Jiexin; Wu, Ying

2018-06-13

The most widely used localization technology is the two-step method that localizes transmitters by measuring one or more specified positioning parameters. Direct position determination (DPD) is a promising technique that directly localizes transmitters from sensor outputs and can offer superior localization performance. However, existing DPD algorithms such as maximum likelihood (ML)-based and multiple signal classification (MUSIC)-based estimations are computationally expensive, making it difficult to satisfy real-time demands. To solve this problem, we propose the use of a modular neural network for multiple-source DPD. In this method, the area of interest is divided into multiple sub-areas. Multilayer perceptron (MLP) neural networks are employed to detect the presence of a source in a sub-area and filter sources in other sub-areas, and radial basis function (RBF) neural networks are utilized for position estimation. Simulation results show that a number of appropriately trained neural networks can be successfully used for DPD. The performance of the proposed MLP-MLP-RBF method is comparable to the performance of the conventional MUSIC-based DPD algorithm for various signal-to-noise ratios and signal power ratios. Furthermore, the MLP-MLP-RBF network is less computationally intensive than the classical DPD algorithm and is therefore an attractive choice for real-time applications.

The source apportionment of polycyclic aromatic hydrocarbons (PAHs) in the topsoil in Xiaodian sewage irrigation area, North of China.

PubMed

Li, Jia-Le; Wang, Yan-Xin; Zhang, Cai-Xiang; Dong, Yi-Hui; Du, Bin; Liao, Xiao-Ping

2014-12-01

31 topsoil samples were collected by grid method in Xiaodian sewage irrigation area, Taiyuan City, North of China. The concentrations of 16 kinds of polycyclic aromatic hydrocarbons (PAHs) were determined by gas chromatograph coupled with mass spectrum. Generally speaking, the distribution order of PAHs in the area is: those with five and six rings > those with four rings > those with two and three rings. Source apportionment shows a significant zonation of the source of PAHs: the civil coal pollution occurred in the north part, the local and far factory pollution happened in the middle area and the mixed pollution sources from coal and wood combustion, automotive emission, presented in the south area. The distribution of PAHs has a definite relationship with the sewage water flow and soil adsorption. The related coefficient between PAHs and physicochemical property showed there was a negative correlation between pH, silt, clay and PAHs while there was a positive correlation between total organic carbon, sand and PAHs.

Analysis of Nitrogen Loads From Long Island Sound Watersheds, 1988-98

NASA Astrophysics Data System (ADS)

Mullaney, J. R.; Trench, E. C.

2001-05-01

The U.S. Geological Survey (USGS) recently estimated annual nonpoint-source nitrogen loads from watersheds that drain to Long Island Sound. The study, was conducted in cooperation with the Connecticut Department of Environmental Protection, the New York State Department of Environmental Conservation and the U.S. Environmental Protection Agency, to assist these agencies with the issue of low concentrations of dissolved oxygen in Long Island Sound caused by nitrogen enrichment. A regression model was used to determine annual nitrogen loads at 27 streams monitored by the USGS during 1988-98. Estimates of nitrogen loads from municipal wastewater-treatment plants (where applicable) were subtracted from the total nitrogen loads to determine the nonpoint-source nitrogen load for each water-quality monitoring station. The nonpoint-source load information was applied to unmonitored areas by comparing the land-use and land-cover characteristics of monitored areas with unmonitored areas, and selecting basins that were most similar. In extrapolating load estimates to unmonitored areas, regional differences in mean annual runoff between monitored and unmonitored areas also were considered, using flow information from nearby USGS gaging stations. Estimates of nonpoint nitrogen loads from monitored areas with point sources of nitrogen discharge and estimates from unmonitored areas are subject to uncertainty. These estimates could be improved with additional data collection in coastal basins and in basins with a large percentage of urbanized land, measurements of instream transformation or losses of nitrogen, improved reporting of total nitrogen concentrations from municipal wastewater treatment facilities, and tracking of intrabasin and (or) interbasin diversion of water.

Assessment of potential migration of radionuclides and trace elements from the White Mesa uranium mill to the Ute Mountain Ute Reservation and surrounding areas, southeastern Utah

USGS Publications Warehouse

Naftz, David L.; Ranalli, Anthony J.; Rowland, Ryan C.; Marston, Thomas M.

2011-01-01

In 2007, the Ute Mountain Ute Tribe requested that the U.S. Environmental Protection Agency and U.S. Geological Survey conduct an independent evaluation of potential offsite migration of radionuclides and selected trace elements associated with the ore storage and milling process at an active uranium mill site near White Mesa, Utah. Specific objectives of this study were (1) to determine recharge sources and residence times of groundwater surrounding the mill site, (2) to determine the current concentrations of uranium and associated trace elements in groundwater surrounding the mill site, (3) to differentiate natural and anthropogenic contaminant sources to groundwater resources surrounding the mill site, (4) to assess the solubility and potential for offsite transport of uranium-bearing minerals in groundwater surrounding the mill site, and (5) to use stream sediment and plant material samples from areas surrounding the mill site to identify potential areas of offsite contamination and likely contaminant sources.

Greenhouse gas and ammonia emissions from an open-freestall dairy in southern idaho.

PubMed

Leytem, April B; Dungan, Robert S; Bjorneberg, David L; Koehn, Anita C

2013-01-01

Concentrated dairy operations emit trace gases such as ammonia (NH), methane (CH), and nitrous oxide (NO) to the atmosphere. The implementation of air quality regulations in livestock-producing states increases the need for accurate on-farm determination of emission rates. Our objective was to determine the emission rates of NH, CH, and NO from the open-freestall and wastewater pond source areas on a commercial dairy in southern Idaho using a flush system with anaerobic digestion. Gas concentrations and wind statistics were measured and used with an inverse dispersion model to calculate emission rates. Average emissions per cow per day from the open-freestall source area were 0.08 kg NH, 0.41 kg CH, and 0.02 kg NO. Average emissions from the wastewater ponds (g m d) were 6.8 NH, 22 CH, and 0.2 NO. The combined emissions on a per cow per day basis from the open-freestall and wastewater pond areas averaged 0.20 kg NH and 0.75 kg CH. Combined NO emissions were not calculated due to limited available data. The wastewater ponds were the greatest source of total farm NH emissions (67%) in spring and summer. The emissions of CH were approximately equal from the two source areas in spring and summer. During the late fall and winter months, the open-freestall area constituted the greatest source area of NH and CH emissions. Data from this study can be used to develop trace gas emissions factors from open-freestall dairies in southern Idaho and other open-freestall production systems in similar climatic regions. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

40 CFR Appendix D to Part 58 - Network Design Criteria for Ambient Air Quality Monitoring

Code of Federal Regulations, 2013 CFR

2013-07-01

... determine the extent of regional pollutant transport among populated areas; and in support of secondary... sources within the area, transport of O3 and its precursors, and the photochemical processes related to O3... precursor concentrations entering the area and will identify those areas which are subjected to transport...

40 CFR Appendix D to Part 58 - Network Design Criteria for Ambient Air Quality Monitoring

Code of Federal Regulations, 2014 CFR

2014-07-01

... determine the extent of regional pollutant transport among populated areas; and in support of secondary... sources within the area, transport of O3 and its precursors, and the photochemical processes related to O3... precursor concentrations entering the area and will identify those areas which are subjected to transport...

Determination of Phenols and Trimethylamine in Industrial Effluents

NASA Technical Reports Server (NTRS)

Levaggi, D. A.; Feldstein, M.

1971-01-01

For regulatory purposes to control certain odorous compounds the analysis of phenols and trimethylamines in industrial effluents is necessary. The Bay Area Air Pollution Control District laboratory has been determining these gases by gas chromatographic techniques. The procedures for sample collection, preparation for analysis and determination are described in detail. Typical data from various sources showing the effect of proposed regulations is shown. Extensive sampling and usage of these procedures has shown them to be accurate, reliable and suitable to all types of source effluents.

Use of chemistry and stable sulfur isotopes to determine sources of trends in sulfate of Colorado lakes

USGS Publications Warehouse

Turk, J.T.; Campbell, D.H.; Spahr, N.E.

1993-01-01

The chemistry of lakes in the Mt. Zukel Wilderness Area (MZWA) and the Weminuche Wilderness Area (WWA) of Colorado has been monitored since 1985. The initial results indicate that changes have occurred in the chemistry of some lakes in both areas. Increased concentration of sulfate in lakes may be related to increased atmospheric deposition of sulfate or to changes of sulfate released by weathering and to changing dilution of sulfate by snowmelt. Stable S isotopes seem to be capable of separating the fraction of change in sulfate that is related to atmospheric and watershed sources. Because of the short period of record, it is not possible to determine whether the changes are part of a long-term trend or are merely natural fluctuations about some baseline.The chemistry of lakes in th Mt. Zirkel Wilderness Area (MZWA) and Weminche Wilderness Area (WWA) of Colorado has been monitored since 1985. The initial results indicate that changes have occured in the chemistry of some lakes in both areas. Increased concentration of sulfate in lakes may be related to increased atmospheric deposition of sulfateor to changes of sulfate released by weathering and to changing dilution of sulfate by snowmelt. Stable S isotopes seem to be capable of separating the fraction of change in sulfate that is related to atmospheric and watershed sources. Because of the short period of record, it is not possible to determine whether the changes are part of long-term or are merely natural fluctuations about some baseline.

Methods Used to Assess the Susceptibility to Contamination of Transient, Non-Community Public Ground-Water Supplies in Indiana

USGS Publications Warehouse

Arihood, Leslie D.; Cohen, David A.

2006-01-01

The Safe Water Drinking Act of 1974 as amended in 1996 gave each State the responsibility of developing a Source-Water Assessment Plan (SWAP) that is designed to protect public-water supplies from contamination. Each SWAP must include three elements: (1) a delineation of the source-water protection area, (2) an inventory of potential sources of contaminants within the area, and (3) a determination of the susceptibility of the public-water supply to contamination from the inventoried sources. The Indiana Department of Environmental Management (IDEM) was responsible for preparing a SWAP for all public-water supplies in Indiana, including about 2,400 small public ground-water supplies that are designated transient, non-community (TNC) supplies. In cooperation with IDEM, the U.S. Geological Survey compiled information on conditions near the TNC supplies and helped IDEM complete source-water assessments for each TNC supply. The delineation of a source-water protection area (called the assessment area) for each TNC ground-water supply was defined by IDEM as a circular area enclosed by a 300-foot radius centered at the TNC supply well. Contaminants of concern (COCs) were defined by IDEM as any of the 90 contaminants for which the U.S. Environmental Protection Agency has established primary drinking-water standards. Two of these, nitrate as nitrogen and total coliform bacteria, are Indiana State-regulated contaminants for TNC water supplies. IDEM representatives identified potential point and nonpoint sources of COCs within the assessment area, and computer database retrievals were used to identify potential point sources of COCs in the area outside the assessment area. Two types of methods-subjective and subjective hybrid-were used in the SWAP to determine susceptibility to contamination. Subjective methods involve decisions based upon professional judgment, prior experience, and (or) the application of a fundamental understanding of processes without the collection and analysis of data for a specific condition. Subjective hybrid methods combine subjective methods with quantitative hydrologic analyses. The subjective methods included an inventory of potential sources and associated contaminants, and a qualitative description of the inherent susceptibility of the area around the TNC supply. The description relies on a classification of the hydrogeologic and geomorphic characteristics of the general area around the TNC supply in terms of its surficial geology, regional aquifer system, the occurrence of fine- and coarse-grained geologic materials above the screen of the TNC well, and the potential for infiltration of contaminants. The subjective hybrid method combined the results of a logistic regression analysis with a subjective analysis of susceptibility and a subjective set of definitions that classify the thickness of fine-grained geologic materials above the screen of a TNC well in terms of impedance to vertical flow. The logistic regression determined the probability of elevated concentrations of nitrate as nitrogen (greater than or equal to 3 milligrams per liter) in ground water associated with specific thicknesses of fine-grained geologic materials above the screen of a TNC well. In this report, fine-grained geologic materials are referred to as a geologic barrier that generally impedes vertical flow through an aquifer. A geologic barrier was defined to be thin for fine-grained materials between 0 and 45 feet thick, moderate for materials between 45 and 75 feet thick, and thick if the fine-grained materials were greater than 75 feet thick. A flow chart was used to determine the susceptibility rating for each TNC supply. The flow chart indicated a susceptibility rating using (1) concentrations of nitrate as nitrogen and total coliform bacteria reported from routine compliance monitoring of the TNC supply, (2) the presence or absence of potential sources of regulated contaminants (nitrate as nitrogen and coliform bac

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fulle, D.J.; Bilello, M.A.; Armstrong, J.A.

The US Trade and Development Agency is partially funding the initial phase of an ambient air quality monitoring program for the Metropolitan Municipality of Istanbul in Turkey. The objectives of the monitoring program are fourfold: (1) to ascertain existing levels of air pollution within the urban area; (2) to identify locations where there may be health concerns associated with existing levels of air pollution; (3) to determine the portion of air pollution arising from specific anthropogenic sources within the urban area; and (4) to target the major sources for an emission-reduction program. This program is being carried out in phases.more » A feasibility study has recently been completed. This initial activity will be followed by three main program phases. Phase 1 will involve the installation of several air quality monitoring stations to collect area-wide background data within and surrounding the Municipality. Phase 2 will consist of taking detailed pollutant measurements near specific sources and in specific areas of high pollutant concentrations identified in Phase 1. Phase 3 would target the major sources for emission reductions to improve local air quality and would institute revisions to the existing air quality permitting program. The feasibility study included determining the pollutants of concern, specifying the equipment that should be utilized in Phase 1 for the collection of the data, recommending the number and location of sites where data should be collected, determining site preparation and security needs, and defining the data reduction and analysis techniques which should be employed. This paper describes the results of the feasibility study and outlines plans for the remaining phases of the program.« less

77 FR 4510 - Air Quality Implementation Plans; Kentucky; Attainment Plan for the Kentucky Portion of the...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-30

... and population based apportionment of the area and nonroad sectors to support the mobile source... and nitrogen oxides (NO X ) for the mobile source contribution to ambient PM 2.5 levels for the.... Attainment Date B. Insignificance Determination for the Mobile Source Contribution to PM 2.5 and NO X...

76 FR 20606 - Proposed Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-13

... source(s) Location of referenced ground [caret] Communities affected elevation ** Elevation in meters (MSL) Effective Modified Sevier County, Utah, and Incorporated Areas Albinus Canyon Approximately 400... Creek Split Flow Approximately 400 feet None +5435 Town of Joseph. downstream of State Highway 118. At...

Nutrient and phytoplankton analysis of a Mediterranean coastal area.

PubMed

Sebastiá, M T; Rodilla, M

2013-01-01

Identifying and quantifying the key anthropogenic nutrient input sources are essential to adopting management measures that can target input for maximum effect in controlling the phytoplankton biomass. In this study, three systems characterized by distinctive main nutrient sources were sampled along a Mediterranean coast transect. These sources were groundwater discharge in the Ahuir area, the Serpis river discharge in the Venecia area, and a submarine wastewater outfall 1,900 m from the coast. The study area includes factors considered important in determining a coastal area as a sensitive area: it has significant nutrient sources, tourism is a major source of income in the region, and it includes an area of high water residence time (Venecia area) which is affected by the harbor facilities and by wastewater discharges. We found that in the Ahuir and the submarine wastewater outfall areas, the effects of freshwater inputs were reduced because of a greater water exchange with the oligotrophic Mediterranean waters. On the other hand, in the Venecia area, the highest levels of nutrient concentration and phytoplankton biomass were attributed to the greatest water residence time. In this enclosed area, harmful dinoflagellates were detected (Alexandrium sp. and Dinophysis caudata). If the planned enlargement of the Gandia Harbor proceeds, it may increase the vulnerability of this system and provide the proper conditions of confinement for the dinoflagellate blooms' development. Management measures should first target phosphorus inputs as this is the most potential-limiting nutrient in the Venecia area and comes from a point source that is easier to control. Finally, we recommend that harbor environmental management plans include regular monitoring of water quality in adjacent waters to identify adverse phytoplankton community changes.

Determination of fluoride source in ground water using petrographic studies in Dashtestan area, south of Iran

NASA Astrophysics Data System (ADS)

Battaleb-Looie, Sedigheh; Moore, Farid, ,, Dr.

2010-05-01

The groundwater occurs in Dashtestan area, contains a high level of fluoride. Since groundwater is vastly used for drinking and irrigation purposes, the local residents are at high risk of fluoride toxicity, as already evidenced by the occurrence of dental Fluorosis in many residents. 35 surface and groundwater samples were collected in September, 2009. The results show that in 23 samples the fluoride concentration is above the permissible level (1.5ppm). Petrographic study of lithological units in the catchment area indicates that mica minerals are the most probable source of fluoride content in the study area.

Statistical interpretation of pollution data from satellites. [for levels distribution over metropolitan area

NASA Technical Reports Server (NTRS)

Smith, G. L.; Green, R. N.; Young, G. R.

1974-01-01

The NIMBUS-G environmental monitoring satellite has an instrument (a gas correlation spectrometer) onboard for measuring the mass of a given pollutant within a gas volume. The present paper treats the problem: How can this type measurement be used to estimate the distribution of pollutant levels in a metropolitan area. Estimation methods are used to develop this distribution. The pollution concentration caused by a point source is modeled as a Gaussian plume. The uncertainty in the measurements is used to determine the accuracy of estimating the source strength, the wind velocity, diffusion coefficients and source location.

SABRE MULTI-LAB, STATISTICALLY-BASED MICROCOSM STUDY FOR TCE SOURCE ZONE REMEDIATION (ABSTRACT ONLY)

EPA Science Inventory

SABRE (source area bioremediation) is a public/private consortium of twelve companies, two government agencies, and three research institutions whose charter is to determine if enhanced anaerobic bioremediation can result in effective and quantifiable treatment of chlorinated sol...

76 FR 26982 - Proposed Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-10

.... Specifically, it addresses the flooding source Licking River (Cave Run Lake). DATES: Comments are to be... Incorporated Areas,'' addressed the flooding source Licking River (Cave Run Lake). That table contained... River (Cave Run Lake)....... At the Buck Creek None +765 City of Frenchburg, confluence. Unincorporated...

Possible sources of archaeological maize found in Chaco Canyon and Aztec Ruin, New Mexico

USGS Publications Warehouse

Benson, L.V.; Stein, J.R.; Taylor, Howard E.

2009-01-01

Maize played a major role in Chaco's interaction with outlying communities in the southern Colorado Plateau. This paper seeks to determine where archaeological corn cobs brought to Chaco Canyon were grown. Strontium-isotope and trace-metal ratios of 180 soil-water and 18 surface-water sites in the Southern Colorado Plateau have revealed possible source areas for some of 37 archaeological corn cobs from Chaco Canyon and 10 archaeological corn cobs from Aztec Ruin, New Mexico. The most probable source areas for cobs that predate the middle-12th-century drought include several Upper Rio Chaco sites (not including Chaco Canyon). There are many potential source areas for cobs that date to the late A.D. 1100s and early 1200s, all of which lie in the eastern part of the study area. Some Athapascan-age cobs have potential source areas in the Totah, Lobo Mesa, and Dinetah regions. One Gallo Cliff Dwelling cob has a strontium-isotope ratio that exceeds all measured soil-water values. Field sites for this cob may exist in association with Paleozoic and Precambrian rocks found 80-90 km from Chaco Canyon. Potential source areas for most Aztec Ruin cobs (many of which were found in rooms dating to the first half of the 13th-century) appear to be associated with a loess deposit that blankets the Mesa Verde and McElmo Dome regions.

Assessment of airborne heavy metal pollution in soil and lichen in the Meric-Ergene Basin, Turkey.

PubMed

Hanedar, Asude

2015-01-01

In the present study, accumulations of airborne heavy metals in lichen and soil samples were determined on the basis of pollutant source groups by conducting Zinc (Zn), Lead (Pb), Iron (Fe), Copper (Cu), Chromium (Cr), Cadmium (Cd), Arsenic (As), Cobalt (Co) and Manganese (Mn) analyses on a total of 48 samples collected in the periods of May 2014 and August 2014 from 12 sampling points in a heavily industrialized area, a mixed industrial and residential area, an agricultural area and a background area in the Meric-Ergene Basin, and pH and total organic carbon determination was carried out on soil samples. With the obtained data, heavy metal levels were statistically assessed in detail by being associated with each other and with their probable sources; the accumulations found in soil and lichen samples were compared and spatial variances were set forth. Based on the results, it was observed that heavy metal pollution is at high levels particularly in industrialized areas, and that the differences between the cleanest and most polluted levels determined from soil samples for As, Cr, Cd and Pb reach 10 folds. The highest levels of all heavy metals were determined in both the soil and lichen samples collected from the areas in the south-east part of the region, where industrial activities and particularly leather and chemical industries are concentrated. With the comparison of the indication properties of soil and lichen, it was determined that significant and comparable results can be observed in both matrices.

Wet deposition of mercury at a New York state rural site: Concentrations, fluxes, and source areas

NASA Astrophysics Data System (ADS)

Lai, Soon-onn; Holsen, Thomas M.; Hopke, Philip K.; Liu, Peng

Event-based mercury (Hg) precipitation samples were collected with a modified MIC-B sampler between September 2003 and April 2005 at Potsdam, NY to investigate Hg in wet deposition and identify potential source areas using the potential source contribution function (PCSF) and residence time weighted concentration (RTWC) models. The volume-weighted mean (VWM) concentration and wet deposition flux were 5.5ngL-1 and 7.6μgm-2 during the study period, and 5.5ngL-1 and 5.9μgm-2 in 2004, respectively, and show seasonal trends with larger values in the spring and summer. The PSCF model results matched known source areas based on an emission inventory better than did the RTWC results based on the spatial correlation index. Both modeling results identified large Hg source areas that contain a number of coal-fired power plants located in the Upper Ohio River Valley and in southeastern Michigan, as well as in Quebec and Ontario where there are metal production facilities, waste incinerators and paper mills. Emissions from the Atlantic Ocean were also determined to be a potential source.

Size Matters: What Are the Characteristic Source Areas for Urban Planning Strategies?

PubMed Central

Fan, Chao; Myint, Soe W.; Wang, Chenghao

2016-01-01

Urban environmental measurements and observational statistics should reflect the properties generated over an adjacent area of adequate length where homogeneity is usually assumed. The determination of this characteristic source area that gives sufficient representation of the horizontal coverage of a sensing instrument or the fetch of transported quantities is of critical importance to guide the design and implementation of urban landscape planning strategies. In this study, we aim to unify two different methods for estimating source areas, viz. the statistical correlation method commonly used by geographers for landscape fragmentation and the mechanistic footprint model by meteorologists for atmospheric measurements. Good agreement was found in the intercomparison of the estimate of source areas by the two methods, based on 2-m air temperature measurement collected using a network of weather stations. The results can be extended to shed new lights on urban planning strategies, such as the use of urban vegetation for heat mitigation. In general, a sizable patch of landscape is required in order to play an effective role in regulating the local environment, proportional to the height at which stakeholders’ interest is mainly concerned. PMID:27832111

78 FR 78808 - Proposed Flood Elevation Determinations for Pierce County, Washington, and Incorporated Areas

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-27

... sources in Pierce County, Washington. On April 16, 2012, FEMA published a proposed rulemaking at 77 FR...-2013-0002; Internal Agency Docket No. FEMA-B-7748] Proposed Flood Elevation Determinations for Pierce... proposed rule concerning proposed flood elevation determinations for Pierce County, Washington, and...

Arsenic and metals in soils in the vicinity of the Imperial Oil Company Superfund Site, Marlboro Township, Monmouth County, New Jersey. Water-resources investigations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barringer, J.L.; Szabo, Z.; Barringer, T.H.

1998-09-01

Concentrations of arsenic exceed the New Jersey State Cleanup Criterion of 20 parts per million in sandy and clay-rich soils of two residential areas in the vicinity of the Imperial Oil Company Superfund site in Marlboro Township, Monmouth County, New Jersey. In order to determine the source of the arsenic and metals in soils in the two residential areas, soil samples were collected from (1) long-term forested areas, to determine background geologic and regional atmospheric inputs of arsenic and metals; (2) former and current orchards, to assess the range of concentrations of arsenic and metals that could be contributed bymore » past use of pesticides; (3) the Imperial Oil Company Superfund site, to characterize the chemical composition of contamination from activities at the site; (4) a wooded area adjacent to the Superfund site, to determine whether arsenic and metals from the Superfund site were evident; and (5) the two residential areas, to compare soil chemistry in these areas with the chemistry of soils from forests, orchards, and the Superfund site. The soil samples were divided by soil horizon and were analyzed for 23 metals and metalloids, total organic carbon, and total sulfur. Additionally, air-flow models were used to determine whether roasting of arsenic at the Imperial Oil Company Superfund site was a possible source of arsenic in the soils.« less

[Numerical simulation study of SOA in Pearl River Delta region].

PubMed

Cheng, Yan-li; Li, Tian-tian; Bai, Yu-hua; Li, Jin-long; Liu, Zhao-rong; Wang, Xue-song

2009-12-01

Secondary organic aerosols (SOA) is an important component of the atmospheric particle pollution, thus, determining the status and sources of SOA pollution is the premise of deeply understanding the occurrence, development law and the influence factors of the atmospheric particle pollution. Based on the pollution sources and meteorological data of Pearl River Delta region, the study used the two-dimensional model coupled with SOA module to stimulate the status and source of SOA pollution in regional scale. The results show: the generation of SOA presents obvious characteristics of photochemical reaction, and the high concentration appears at about 14:00; SOA concentration is high in some areas of Guangshou and Dongguan with large pollution source-emission, and it is also high in some areas of Zhongshan, Zhuhai and Jiangmen which are at downwind position of Guangzhou and Dongguan. Contribution ratios of several main pollution sources to SOA are: biogenic sources 72.6%, mobile sources 30.7%, point sources 12%, solvent and oil paint sources 12%, surface sources less than 5% respectively.

Water supply dynamics and quality of alternative water sources in low-income areas of Lilongwe City, Malawi

NASA Astrophysics Data System (ADS)

Chidya, Russel C. G.; Mulwafu, Wapulumuka O.; Banda, Sembeyawo C. T.

2016-06-01

Recent studies in many developing countries have shown that Small Scale Independent Providers (SSIPs) in low-income areas (LIAs) are practical alternatives to water utilities. This study explored supply dynamics and quality of alternative water sources in four LIAs of Lilongwe City in Malawi using qualitative and quantitative methods. Household-level surveys (n = 120) and transect walks were employed to determine the socio-economic activities in the areas. One-on-one discussions were made with water source owners (SSIPs) (n = 24). Data on policy and institutional frameworks was collected through desktop study and Key Informant Interviews (n = 25). Quality of the water sources (shallow wells and boreholes) was determined by collecting grab samples (n = 24) in triplicate using 500 mL bottles. Selected physico-chemical and microbiological parameters were measured: pH, EC, TDS, turbidity, water temperature, salinity, K, Na, Ca, Mg, Cl-, F-, NO3-, alkalinity, water hardness, Fecal coliform (FC) and Faecal Streptococci (FS) bacteria. Water quality data was compared with Malawi Bureau of Standards (MBS) and World Health Organization (WHO) guidelines for drinking water. Shallow wells were reported (65%, n = 120) to be the main source of water for household use in all areas. Some policies like prohibition of boreholes and shallow wells in City locations were in conflict with other provisions of water supply, sanitation and housing. High levels of FC (0-2100 cfu/100 mL) and FS (0-1490 cfu/100 mL) at several sites (>90%, n = 24) suggest water contamination likely to impact on human health. This calls for upgrading and recognition of the water sources for improved water service delivery.

Ground-water movement and nitrate in ground water, East Erda area, Tooele County, Utah, 1997-2000

USGS Publications Warehouse

Susong, D.D.

2005-01-01

Nitrate was discovered in ground water in the east Erda area of Tooele County, Utah, in 1994. The U.S. Geological Survey, in cooperation with Tooele County, investigated the ground-water flow system and water quality in the eastern part of Tooele Valley to determine (1) the vertical and horizontal distribution of nitrate, (2) the direction of movement of the nitrate contamination, and (3) the source of the nitrate. The potentiometric surface of the upper part of the basin-fill aquifer indicates that the general direction of ground-water flow is to the northwest, the flow system is complex, and there is a ground-water mound probably associated with springs. The spatial distribution of nitrate reflects the flow system with the nitrate contamination split into a north and south part by the ground-water mound. The distribution of dissolved solids and sulfate in ground water varies spatially. Vertical profiles of nitrate in water from selected wells indicate that nitrate contamination generally is in the upper part of the saturated zone and in some wells has moved downward. Septic systems, mining and smelting, agriculture, and natural sources were considered to be possible sources of nitrate contamination in the east Erda area. Septic systems are not the source of nitrate because water from wells drilled upgradient of all septic systems in the area had elevated nitrate concentrations. Mining and smelting activity are a possible source of nitrate contamination but few data are available to link nitrate contamination with mining sites. Natural and agricultural sources of nitrate are present east of the Erda area but few data are available about these sources. The source(s) of nitrate in the east Erda area could not be clearly delineated in spite of considerable effort and expenditure of resources.

Lead Contamination and Source Characterization in Soils Around a Lead-Zinc Smelting Plant in a Near-Urban Environment in Baoji, China.

PubMed

Deng, Wenbo; Li, Xuxiang; An, Zhisheng; Yang, Liu

2016-11-01

Economic reforms in China since 1978 have promoted nationwide socioeconomic advancement but led to a considerable amount of environmental pollution. The distribution and sources of Pb in a typical peri-urban industrial part of Baoji, China, were assessed by determining the Pb contents and isotopic compositions in 52 topsoil samples from the study area. The topsoil samples were polluted averagely with 40.88 mg Pb kg -1 , was 1.86 times higher than the Pb content of local background soil (22.04 mg kg -1 ). Pb isotopic compositions were determined by analyzing samples prepared using total digestion and acid extraction methods. Radiogenic isotopes contributed more to the Pb concentrations in the acid extracts than in the total digests. This was shown by the 207/206 Pb and 208/206 Pb ratios, which were 0.845-0.88 and 2.088-2.128, respectively, in the acid extracts and 0.841-0.875 and 2.086-2.125, respectively, in the total digests. This indicates that anthropogenic sources of Pb could be identified more sensitively in acid extracts than in total digests. The Pb isotope ratios showed that burning coal and smelting ore are the predominant anthropogenic sources of Pb in the study area, i.e., a lead-zinc smelter and a coking plant are major sources of Pb in the study area.

14 CFR 417.417 - Propellants and explosives.

Code of Federal Regulations, 2012 CFR

2012-01-01

... radio frequency radiation sources in a radio frequency radiation exclusion area. A launch operator must determine the vulnerability of its electro-explosive devices and systems to radio frequency radiation and establish radio frequency radiation power limits or radio frequency radiation exclusion areas as required by...

14 CFR 417.417 - Propellants and explosives.

Code of Federal Regulations, 2013 CFR

2013-01-01

... radio frequency radiation sources in a radio frequency radiation exclusion area. A launch operator must determine the vulnerability of its electro-explosive devices and systems to radio frequency radiation and establish radio frequency radiation power limits or radio frequency radiation exclusion areas as required by...

14 CFR 417.417 - Propellants and explosives.

Code of Federal Regulations, 2011 CFR

2011-01-01

... radio frequency radiation sources in a radio frequency radiation exclusion area. A launch operator must determine the vulnerability of its electro-explosive devices and systems to radio frequency radiation and establish radio frequency radiation power limits or radio frequency radiation exclusion areas as required by...

14 CFR 417.417 - Propellants and explosives.

Code of Federal Regulations, 2014 CFR

2014-01-01

... radio frequency radiation sources in a radio frequency radiation exclusion area. A launch operator must determine the vulnerability of its electro-explosive devices and systems to radio frequency radiation and establish radio frequency radiation power limits or radio frequency radiation exclusion areas as required by...

77 FR 20999 - Final Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-09

... set forth below: * Elevation in feet (NGVD) + Elevation in feet (NAVD) Depth in feet Flooding source(s..., and Incorporated Areas Docket No.: FEMA-B-1100 Mississippi River Approximately 11.2 miles +585 City of.... Approximately 12.8 miles +594 upstream of State Highway 136. * National Geodetic Vertical Datum. + North...

Gas Eruptions Taper Off in Northwestern Oklahoma.

ERIC Educational Resources Information Center

Preston, Don

1980-01-01

Describes the eruption of inflammable natural gas from the ground surface in the Edith area near Camp Houston. Determining the source of the gas, the results established the Chester-Oswago interval as the most likely source. The surface venting has declined steadily; the likelihood of finding its cause is also described. (SK)

Survey on the Sources of Information in Science, Technology and Commerce in the State of Penang, Malaysia

ERIC Educational Resources Information Center

Tee, Lim Huck; Fong, Tang Wan

1973-01-01

Penang, Malaysia is undergoing rapid industrialization to stimulate its economy. A survey was conducted to determine what technical, scientific, and commercial information sources were available. Areas covered in the survey were library facilities, journals, commercial reference works and audio-visual materials. (DH)

[Research on stormwater runoff quality of mountain city by source area monitoring].

PubMed

Li, Li-Qing; Shan, Bao-Qing; Zhao, Jian-Wei; Guo, Shu-Gang; Gao, Yong

2012-10-01

Stormwater runoff samples were collected from 10 source areas in Mountain City, Chongqing, during five rain events in an attempt to investigate the characteristics of runoff quality and influencing factors. The outcomes are expected to offer practical guidance of sources control of urban runoff pollution. The results indicated that the stormwater runoff of Mountain City presented a strong first flush for almost all events and constituents. The runoff quality indices were also influenced by the rainfall intensity. The concentration of TSS, COD, TN and TP decreased as the rainfall intensity increased. The concentrations of COD and TP in stormwater runoff were highly correlated with TSS concentrations. Suspended solid matter were not only the main pollutant of stormwater runoff but also served as the vehicle for transport of organic matter and phosphorus. Organic matter and phosphorus in stormwatrer runoff were mainly bound to particles, whereas nitrogen was predominantly dissolved, with ammonia and nitrate. A significant difference of stormwater runoff quality was observed among the ten monitored source areas. The highest magnitude of urban stormwater runoff pollution was expected in the commercial area and the first trunk road, followed by the minor road, residential area, parking lot and roof. Urban surface function, traffic volume, population density, and street sweeping practice are the main factors determining spatial differentiation of urban surface runoff quality. Commercial area, the first trunk road and residential area with high population density are the critical sources areas of urban stormwater runoff pollution.

Seismic Source Scaling and Discrimination in Diverse Tectonic Environments

DTIC Science & Technology

2009-09-30

3349-3352. Imanishi, K., W. L. Ellsworth, and S. G. Prejean (2004). Earthquake source parameters determined by the SAFOD Pilot Hole seismic array ... seismic discrimination by performing a thorough investigation of* earthquake source scaling using diverse, high-quality datascts from varied tectonic...these corrections has a direct impact on our ability to identify clandestine explosions in the broad regional areas characterized by low seismicity

Cooperative geochemical investigation of geothermal resources in the Imperial Valley and Yuma areas. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Coplen, T.B.

1973-10-01

Preliminary studies indicate that the Imperial Valley has a large geothermal potential. In order to delineate additional geothermal systems a chemical and isotopic investigation of samples from water wells, springs, and geothermal wells in the Imperial Valley and Yuma areas was conducted. Na, K, and Ca concentrations of nearly 200 well water, spring water, hot spring, and geothermal fluid samples from the Imperial Valley area were measured by atomic absorption spectrophotometry. Fournier and Truesdell's function was determined for each water sample. Suspected geothermal areas are identified. Hydrogen and oxygen isotope abundances were determined in order to determine and to identifymore » the source of the water in the Mesa geothermal system. (JGB)« less

Sources and geographic origin of particulate matter in urban areas of the Danube macro-region: The cases of Zagreb (Croatia), Budapest (Hungary) and Sofia (Bulgaria).

PubMed

Perrone, M G; Vratolis, S; Georgieva, E; Török, S; Šega, K; Veleva, B; Osán, J; Bešlić, I; Kertész, Z; Pernigotti, D; Eleftheriadis, K; Belis, C A

2018-04-01

The contribution of main PM pollution sources and their geographic origin in three urban sites of the Danube macro-region (Zagreb, Budapest and Sofia) were determined by combining receptor and Lagrangian models. The source contribution estimates were obtained with the Positive Matrix Factorization (PMF) receptor model and the results were further examined using local wind data and backward trajectories obtained with FLEXPART. Potential Source Contribution Function (PSCF) analysis was applied to identify the geographical source areas for the PM sources subject to long-range transport. Gas-to-particle transformation processes and primary emissions from biomass burning are the most important contributors to PM in the studied sites followed by re-suspension of soil (crustal material) and traffic. These four sources can be considered typical of the Danube macro-region because they were identified in all the studied locations. Long-range transport was observed of: a) sulphate-enriched aged aerosols, deriving from SO 2 emissions in combustion processes in the Balkans and Eastern Europe and b) dust from the Saharan and Karakum deserts. The study highlights that PM pollution in the studied urban areas of the Danube macro-region is the result of both local sources and long-range transport from both EU and no-EU areas. Copyright © 2017 The Authors. Published by Elsevier B.V. All rights reserved.

A Study of Regional Waveform Calibration in the Eastern Mediterranean Region.

NASA Astrophysics Data System (ADS)

di Luccio, F.; Pino, A.; Thio, H.

2002-12-01

We modeled Pnl phases from several moderate magnitude events in the eastern Mediterranean to test methods and to develop path calibrations for source determination. The study region spanning from the eastern part of the Hellenic arc to the eastern Anatolian fault is mostly interested by moderate earthquakes, that can produce relevant damages. The selected area consists of several tectonic environment, which produces increased level of difficulty in waveform modeling. The results of this study are useful for the analysis of regional seismicity and for seismic hazard as well, in particular because very few broadband seismic stations are available in the selected area. The obtained velocity model gives a 30 km crustal tickness and low upper mantle velocities. The applied inversion procedure to determine the source mechanism has been successful, also in terms of discrimination of depth, for the entire range of selected paths. We conclude that using the true calibration of the seismic structure and high quality broadband data, it is possible to determine the seismic source in terms of mechanism, even with a single station.

Synthetic aperture radar imagery of airports and surrounding areas: Study of clutter at grazing angles and their polarimetric properties

NASA Technical Reports Server (NTRS)

Onstott, Robert G.; Gineris, Denise J.; Clinthorne, James T.

1991-01-01

The statistical description of ground clutter at an airport and in the surrounding area is addressed. These data are being utilized in a program to detect microbursts. Synthetic aperture radar data were collected at the Denver Stapleton Airport. Mountain terrain data were examined to determine if they may potentially contribute to range ambiguity problems and degrade microburst detection. Results suggest that mountain clutter may not present a special problem source. The examination of clutter at small grazing angles was continued by examining data collected at especially low altitudes. Cultural objects such as buildings produce strong sources of backscatter at angles of about 85 deg, with responses of 30 dB to 60 dB above the background. Otherwise there are a few sources which produce significant scatter. The polarization properties of hydrospheres and clutter were examined with the intent of determining the optimum polarization. This polarization was determined to be dependent upon the ratio of VV and HH polarizations of both rain and ground clutter.

Radiocarbon determination of fossil and contemporary carbon contribution to aerosol in the Pacific Islands.

PubMed

Isley, C F; Nelson, P F; Taylor, M P; Williams, A A; Jacobsen, G E

2018-06-21

Combustion emissions are of growing concern across all Pacific Island Countries, which account for >10,000 km 2 of the earth's surface area; as for many other small island states globally. Apportioning emissions inputs for Suva, the largest Pacific Island city, will aid in development of emission reduction strategies. Total suspended particulate (TSP) and fine particulate (PM 2.5 ) samples were collected for Suva City, a residential area (Kinoya, TSP) and a mainly ocean-influenced site (Suva Point, TSP) from 2014 to 2015. Percentages of contemporary and fossil carbon were determined by radiocarbon analysis (accelerator mass spectrometry); for non‑carbonate carbon (NCC), elemental carbon (EC) and organic carbon (OC). Source contributions to particulate matter were identified and the accuracy of previous emissions inventory and source apportionment studies was evaluated. Suva Point NCC concentrations (2.7 ± 0.4 μg/m 3 ) were four times lower than for City (13 ± 2 μg/m 3 in TSP) and Kinoya (13 ± 1 μg/m 3 in TSP); demonstrating the contribution of land-based emissions activities in city and residential areas. In Suva City, total NCC in air was 81% (79%-83%) fossil carbon, from vehicles, shipping, power generation and industry; whilst in the residential area, 48% (46%-50%) of total NCC was contemporary carbon; reflecting the higher incidence of biomass and waste burning and of cooking activities. Secondary organic fossil carbon sources contributed >36% of NCC mass at the city and >29% at Kinoya; with biogenic carbon being Kinoya's most significant source (approx. 30% of NCC mass). These results support the previous source apportionment studies for the city area; yet show that, in line with emissions inventory studies, biomass combustion contributes more PM 2.5 mass in residential areas. Hence air quality management strategies need to target open burning activities as well as fossil fuel combustion. Copyright © 2018 Elsevier B.V. All rights reserved.

FISH TISSUE QUALITY IN NEAR-COASTAL AREAS OF THE GULF OF MEXICO RECEIVING POINT SOURCE DISCHARGES

EPA Science Inventory

The objective of this study was to determine inorganic and organic contaminant concentrations in edible tissue of fish collected from eight coastal areas receiving wastewater discharges and from two reference locations. Trace metal residues were statistically similar regardless o...

Remote Sensing of Plastic Debris

NASA Astrophysics Data System (ADS)

Garaba, S. P.; Dierssen, H. M.

2016-02-01

Plastic debris is becoming a nuisance in the environment and as a result there has been a dire need to synoptically detect and quantify them in the ocean and on land. We investigate the possible utility of spectral information determined from hand held, airborne and satellite remote sensing tools in the detection and identification polymer source of plastic debris. Sampled debris will be compared to our derived spectral library of typical raw polymer sources found at sea and in household waste. Additional work will be to determine ways to estimate the abundance of plastic debris in target areas. Implications of successful remote detection, tracking and quantification of plastic debris will be towards validating field observations over large areas and at repeated time intervals both on land and at sea.

Growth phenology of coast Douglas-fir seed sources planted in diverse environments.

PubMed

Gould, Peter J; Harrington, Constance A; St Clair, J Bradley

2012-12-01

The timing of periodic life cycle events in plants (phenology) is an important factor determining how species and populations will react to climate change. We evaluated annual patterns of basal-area and height growth of coast Douglas-fir (Pseudotusga menziesii var. menziesii (Mirb.) Franco) seedlings from four seed sources that were planted in four diverse environments as part of the Douglas-fir Seed-Source Movement Trial. Stem diameters and heights were measured periodically during the 2010 growing season on 16 open-pollinated families at each study installation. Stem diameters were measured on a subset of trees with electronic dendrometers during the 2010 and 2011 growing seasons. Trees from the four seed sources differed in phenology metrics that described the timing of basal-area and height-growth initiation, growth cessation and growth rates. Differences in the height-growth metrics were generally larger than differences in the basal-area growth metrics and differences among installations were larger than differences among seed sources, highlighting the importance of environmental signals on growth phenology. Variations in the height- and basal-area growth metrics were correlated with different aspects of the seed-source environments: precipitation in the case of height growth and minimum temperature in the case of basal-area growth. The detailed dendrometer measurements revealed differences in growth patterns between seed sources during distinct periods in the growing season. Our results indicate that multiple aspects of growth phenology should be considered along with other traits when evaluating adaptation of populations to future climates.

Climatology of dust distribution over West Asia from homogenized remote sensing data

NASA Astrophysics Data System (ADS)

Nabavi, Seyed Omid; Haimberger, Leopold; Samimi, Cyrus

2016-06-01

In the past decade, West Asia has witnessed more frequent and intensified dust storms affecting Iran and Persian Gulf countries. Employing a varying threshold that takes into account systematic differences between TOMS and OMI data, TOMS-OMI Aerosol Index data are used to identify long-term changes in the horizontal distribution of dust storms in West Asia from 1980 to present. The northwest of Iraq and east of Syria are identified as emerging dusty areas, whereas east of Saudi Arabia and southeast of Iraq are identified as permanent dusty areas, including both dust sources and affected areas. Whereas the frequency of dust events increased slightly in the permanent dusty areas, it increased markedly in the emerging dusty areas. As expected, the frequency of dust events is highest in June and July. The dust source areas are identified as the Iraq-Saudi Arabia boundary region and (recently) the northwest of Iraq, using MODIS deep blue aerosol optical depth data. Subsequently, a lagged correlation was implemented between identified dust sources and whole West Asia to determine the main paths and receptors of intense dust storms. Accordingly, southwest of Iran and Persian Gulf countries were determined as main receptors of summertime dust storms in West Asia. During spring, dust storms mostly hit the northern half of the region and reach to the Caspian Sea. Analyzing atmospheric patterns, Shamal and Frontal patterns were found as dominant atmospheric circulations simultaneous with summertime and springtime dust storms, respectively.

Use of Nitrogen-15 Isotope Method in Soils and Ground Water to Determine Potential Nitrogen Sources Affecting a Municipal Water Supply in Kansas, USA

NASA Astrophysics Data System (ADS)

Townsend, M. A.; Macko, S. A.

2004-12-01

Nitrate-N concentrations have increased to greater than 10 mg/L in a municipal water supply in western Kansas from 1995 to 2002. A study was done by the Kansas Geological Survey using the nitrogen-15 natural abundance isotope method to determine potential sources for the increasing nitrate concentrations. Preliminary results of the isotope analyses on water samples suggest that animal waste and/or denitrification enrichment has affected the water supply. Soil samples from areas near the wells that were not treated with manure show a general increase of nitrogen-15 signature (+9 to +15 \\permil) to a depth of 5 m. Soils are silt loams with measurable carbonate (0.8 to 2 % by weight) in the profile, which may permit volatilization enrichment to occur in the soil profile. Wells in the area range from 11 to 20 m in alluvial deposits with depth to water at approximately 9 m). Nitrate-N values range from 8 to 26 mg/L. Nitrogen-15 values range from (+17 to +28 \\permil) with no obvious source of animal waste near the well sites. There are potential nearby long-term sources of animal waste - an abandoned sewage treatment plant and an agricultural testing farm. One well has a reducing chemistry with a nitrate value of 0.9 mg/L and a nitrogen-15 value of +17 \\permil suggesting that alluvial sediment variation also has an impact on the water quality in the study area. The other wells show values of nitrate and nitrogen-15 that are much greater than the associated soils. The use of nitrogen-15 alone permited limited evaluation of sources of nitrate to ground water particularly in areas with carbonate in the soils. Use of oxygen-18 on nitrate will permit the delineation of the processes affecting the nitrogen in the soil profile and determination of the probable sources and the processes that have affected the nitrogen in the ground water. Final results of the nitrogen-15 and oxygen-18 analyses will be presented.

Search for Extended Sources in the Galactic Plane Using Six Years of Fermi-Large Area Telescope Pass 8 Data above 10 GeV

DOE PAGES

Ackermann, M.; Ajello, M.; Baldini, L.; ...

2017-07-10

The spatial extension of a γ-ray source is an essential ingredient to determine its spectral properties, as well as its potential multiwavelength counterpart. The capability to spatially resolve γ-ray sources is greatly improved by the newly delivered Fermi-Large Area Telescope (LAT) Pass 8 event-level analysis, which provides a greater acceptance and an improved point-spread function, two crucial factors for the detection of extended sources. Here, we present a complete search for extended sources located within 7° from the Galactic plane, using 6 yr of Fermi-LAT data above 10 GeV. We find 46 extended sources and provide their morphological and spectralmore » characteristics. As a result, this constitutes the first catalog of hard Fermi-LAT extended sources, named the Fermi Galactic Extended Source Catalog, which allows a thorough study of the properties of the Galactic plane in the sub-TeV domain.« less

Search for Extended Sources in the Galactic Plane Using Six Years of Fermi -Large Area Telescope Pass 8 Data above 10 GeV

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ackermann, M.; Buehler, R.; Ajello, M.

The spatial extension of a γ -ray source is an essential ingredient to determine its spectral properties, as well as its potential multiwavelength counterpart. The capability to spatially resolve γ -ray sources is greatly improved by the newly delivered Fermi -Large Area Telescope (LAT) Pass 8 event-level analysis, which provides a greater acceptance and an improved point-spread function, two crucial factors for the detection of extended sources. Here, we present a complete search for extended sources located within 7° from the Galactic plane, using 6 yr of Fermi -LAT data above 10 GeV. We find 46 extended sources and providemore » their morphological and spectral characteristics. This constitutes the first catalog of hard Fermi -LAT extended sources, named the Fermi Galactic Extended Source Catalog, which allows a thorough study of the properties of the Galactic plane in the sub-TeV domain.« less

Search for Extended Sources in the Galactic Plane Using Six Years of Fermi-Large Area Telescope Pass 8 Data above 10 GeV

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ackermann, M.; Ajello, M.; Baldini, L.

The spatial extension of a γ-ray source is an essential ingredient to determine its spectral properties, as well as its potential multiwavelength counterpart. The capability to spatially resolve γ-ray sources is greatly improved by the newly delivered Fermi-Large Area Telescope (LAT) Pass 8 event-level analysis, which provides a greater acceptance and an improved point-spread function, two crucial factors for the detection of extended sources. Here, we present a complete search for extended sources located within 7° from the Galactic plane, using 6 yr of Fermi-LAT data above 10 GeV. We find 46 extended sources and provide their morphological and spectralmore » characteristics. As a result, this constitutes the first catalog of hard Fermi-LAT extended sources, named the Fermi Galactic Extended Source Catalog, which allows a thorough study of the properties of the Galactic plane in the sub-TeV domain.« less

Search for Extended Sources in the Galactic Plane Using Six Years of Fermi-Large Area Telescope Pass 8 Data above 10 GeV

NASA Astrophysics Data System (ADS)

Ackermann, M.; Ajello, M.; Baldini, L.; Ballet, J.; Barbiellini, G.; Bastieri, D.; Bellazzini, R.; Bissaldi, E.; Bloom, E. D.; Bonino, R.; Bottacini, E.; Brandt, T. J.; Bregeon, J.; Bruel, P.; Buehler, R.; Cameron, R. A.; Caragiulo, M.; Caraveo, P. A.; Castro, D.; Cavazzuti, E.; Cecchi, C.; Charles, E.; Chekhtman, A.; Cheung, C. C.; Chiaro, G.; Ciprini, S.; Cohen, J. M.; Costantin, D.; Costanza, F.; Cutini, S.; D'Ammando, F.; de Palma, F.; Desiante, R.; Digel, S. W.; Di Lalla, N.; Di Mauro, M.; Di Venere, L.; Favuzzi, C.; Fegan, S. J.; Ferrara, E. C.; Franckowiak, A.; Fukazawa, Y.; Funk, S.; Fusco, P.; Gargano, F.; Gasparrini, D.; Giglietto, N.; Giordano, F.; Giroletti, M.; Green, D.; Grenier, I. A.; Grondin, M.-H.; Guillemot, L.; Guiriec, S.; Harding, A. K.; Hays, E.; Hewitt, J. W.; Horan, D.; Hou, X.; Jóhannesson, G.; Kamae, T.; Kuss, M.; La Mura, G.; Larsson, S.; Lemoine-Goumard, M.; Li, J.; Longo, F.; Loparco, F.; Lubrano, P.; Magill, J. D.; Maldera, S.; Malyshev, D.; Manfreda, A.; Mazziotta, M. N.; Michelson, P. F.; Mitthumsiri, W.; Mizuno, T.; Monzani, M. E.; Morselli, A.; Moskalenko, I. V.; Negro, M.; Nuss, E.; Ohsugi, T.; Omodei, N.; Orienti, M.; Orlando, E.; Ormes, J. F.; Paliya, V. S.; Paneque, D.; Perkins, J. S.; Persic, M.; Pesce-Rollins, M.; Petrosian, V.; Piron, F.; Porter, T. A.; Principe, G.; Rainò, S.; Rando, R.; Razzano, M.; Razzaque, S.; Reimer, A.; Reimer, O.; Reposeur, T.; Sgrò, C.; Simone, D.; Siskind, E. J.; Spada, F.; Spandre, G.; Spinelli, P.; Suson, D. J.; Tak, D.; Thayer, J. B.; Thompson, D. J.; Torres, D. F.; Tosti, G.; Troja, E.; Vianello, G.; Wood, K. S.; Wood, M.

2017-07-01

The spatial extension of a γ-ray source is an essential ingredient to determine its spectral properties, as well as its potential multiwavelength counterpart. The capability to spatially resolve γ-ray sources is greatly improved by the newly delivered Fermi-Large Area Telescope (LAT) Pass 8 event-level analysis, which provides a greater acceptance and an improved point-spread function, two crucial factors for the detection of extended sources. Here, we present a complete search for extended sources located within 7° from the Galactic plane, using 6 yr of Fermi-LAT data above 10 GeV. We find 46 extended sources and provide their morphological and spectral characteristics. This constitutes the first catalog of hard Fermi-LAT extended sources, named the Fermi Galactic Extended Source Catalog, which allows a thorough study of the properties of the Galactic plane in the sub-TeV domain.

Noncontact analysis of the fiber weight per unit area in prepreg by near-infrared spectroscopy.

PubMed

Jiang, B; Huang, Y D

2008-05-26

The fiber weight per unit area in prepreg is an important factor to ensure the quality of the composite products. Near-infrared spectroscopy (NIRS) technology together with a noncontact reflectance sources has been applied for quality analysis of the fiber weight per unit area. The range of the unit area fiber weight was 13.39-14.14mgcm(-2). The regression method was employed by partial least squares (PLS) and principal components regression (PCR). The calibration model was developed by 55 samples to determine the fiber weight per unit area in prepreg. The determination coefficient (R(2)), root mean square error of calibration (RMSEC) and root mean square error of prediction (RMSEP) were 0.82, 0.092, 0.099, respectively. The predicted values of the fiber weight per unit area in prepreg measured by NIRS technology were comparable to the values obtained by the reference method. For this technology, the noncontact reflectance sources focused directly on the sample with neither previous treatment nor manipulation. The results of the paired t-test revealed that there was no significant difference between the NIR method and the reference method. Besides, the prepreg could be analyzed one time within 20s without sample destruction.

TRAY MOUNTAIN ROADLESS AREA, GEORGIA.

USGS Publications Warehouse

Nelson, Arthur E.; Chatman, Mark L.

1984-01-01

A mineral survey indicates that the Tray Mountain Roadless Area, Georgia has little promise for the occurrence of metallic mineral resources. Rocks underlying the Tray Mountain Roadless Area are suitable for crushed rock or aggregate; however, other sources for these materials are available closer to present markets. There is a possibility for the occurrence of hydrocarbon resources underlying the area at great depth, but no hydrocarbon potential was identified. Detailed studies are needed to establish the presence or absence and mineral-resource potential of olivine, nickel, cobalt, and chrome in the two mafic-ultramafic bodies in the Hayesville thrust sheet. The cause of the lead anomaly in pan concentrate samples taken from the southwest part of the roadless area has not been established; the mineral residence and source of the anomaly remain to be determined.

Geochemical evolution of groundwater in the Mud Lake area, eastern Idaho, USA

USGS Publications Warehouse

Rattray, Gordon W.

2015-01-01

Groundwater with elevated dissolved-solids concentrations—containing large concentrations of chloride, sodium, sulfate, and calcium—is present in the Mud Lake area of Eastern Idaho. The source of these solutes is unknown; however, an understanding of the geochemical sources and processes controlling their presence in groundwater in the Mud Lake area is needed to better understand the geochemical sources and processes controlling the water quality of groundwater at the Idaho National Laboratory. The geochemical sources and processes controlling the water quality of groundwater in the Mud Lake area were determined by investigating the geology, hydrology, land use, and groundwater geochemistry in the Mud Lake area, proposing sources for solutes, and testing the proposed sources through geochemical modeling with PHREEQC. Modeling indicated that sources of water to the eastern Snake River Plain aquifer were groundwater from the Beaverhead Mountains and the Camas Creek drainage basin; surface water from Medicine Lodge and Camas Creeks, Mud Lake, and irrigation water; and upward flow of geothermal water from beneath the aquifer. Mixing of groundwater with surface water or other groundwater occurred throughout the aquifer. Carbonate reactions, silicate weathering, and dissolution of evaporite minerals and fertilizer explain most of the changes in chemistry in the aquifer. Redox reactions, cation exchange, and evaporation were locally important. The source of large concentrations of chloride, sodium, sulfate, and calcium was evaporite deposits in the unsaturated zone associated with Pleistocene Lake Terreton. Large amounts of chloride, sodium, sulfate, and calcium are added to groundwater from irrigation water infiltrating through lake bed sediments containing evaporite deposits and the resultant dissolution of gypsum, halite, sylvite, and bischofite.

Monsoonal variations in atmospheric surfactants at different coastal areas of the Malaysian Peninsula.

PubMed

Jaafar, Shoffian Amin; Latif, Mohd Talib; Razak, Intan Suraya; Shaharudin, Muhammad Zulhilmi; Khan, Md Firoz; Wahid, Nurul Bahiyah Abd; Suratman, Suhaimi

2016-08-15

This study determined the effect of monsoonal changes on the composition of atmospheric surfactants in coastal areas. The composition of anions (SO4(2-), NO3(-), Cl(-), F(-)) and the major elements (Ca, K, Mg, Na) in aerosols were used to determine the possible sources of surfactants. Surfactant compositions were determined using a colorimetric method as methylene blue active substances (MBAS) and disulphine blue active substances (DBAS). The anion and major element compositions of the aerosol samples were determined by ion chromatography (IC) and inductively coupled plasma mass spectrometry (ICP-MS), respectively. The results indicated that the concentrations of surfactant in aerosols were dominated by MBAS (34-326pmolm(-3)). Monsoonal changes were found to significantly affect the concentration of surfactants. Using principal component analysis-multiple linear regressions (PCA-MLR), major possible sources for surfactants in the aerosols were motor vehicle emissions, secondary aerosol and the combustion of biomass along with marine aerosol. Copyright © 2016 Elsevier Ltd. All rights reserved.

Determination of MeHg sources to fish in the St. Louis River, MN, USA, using Hg stable isotopes

EPA Science Inventory

Mercury contamination in the Great Lakes region has become a prevalent concern due to elevated methylmercury (MeHg) levels in fish. While atmospheric deposition of Hg is ubiquitous, releases from legacy point-sources give rise to numerous Areas of Concern (AOCs) across the Great ...

Growth phenology of coast Douglas-fir seed sources planted in diverse environments

Treesearch

Peter J. Gould; Constance A. Harrington; J. Bradley St. Clair

2012-01-01

The timing of periodic life cycle events in plants (phenology) is an important factor determining how species and populations will react to climate change. We evaluated annual patterns of basal-area and height growth of coast Douglas-fir (Pseudotusuga menziesii var. menziesii (Mirb.) Franco) seedlings from four seed sources...

Stable carbon isotopes to monitor the CO2 source mix in the urban environment

NASA Astrophysics Data System (ADS)

Vogel, F. R.; Wu, L.; Ramonet, M.; Broquet, G.; Worthy, D. E. J.

2014-12-01

Urban areas are said to be responsible for approximately 71% of fossil fuel CO2 emissions while comprising only two percent of the land area [IEA, 2008]. This limited spatial expansion could facility a monitoring of anthropogenic GHGs from atmospheric observations. As major sources of emissions, cities also have a huge potential to drive emissions reductions. To effectively manage emissions, cities must however, first establish techniques to validate their reported emission statistics. A pilot study which includes continues 13CO2 data from calibrated cavity ring-down spectrometers [Vogel et al. 2013] of two "sister sites" in the vicinity of Toronto, Canada is contrasted to recent observations of 13CO2 observations in Paris during significant pollution events. Using Miller-Tans plots [Miller and Tans, 2003] for our multi-season observations reveals significant changes of the source signatures of night time CO2 emissions which reflect the importance of natural gas burning in Megacities (up to 80% of fossil fuel sources) and show-case the potential of future isotope studies to determine source sectors. Especially the winter data this approach seems suitable to determine the source contribution of different fuel types (natural gas, liquid fuels and coal) which can inform the interpretation of other Greenhouse Gases and air pollution levels.

Bisphenol A emission factors from industrial sources and elimination rates in a sewage treatment plant.

PubMed

Fuerhacker, M

2003-01-01

Bisphenol A (BPA) is widely used for the production of epoxy resins and polycarbonate plastics and is considered an endocrine disruptor. Special in vitro test systems and animal experiments showed a weak estrogenic activity. Aquatic wildlife especially could be endangered by waste water discharges. To manage possible risks arising from BPA emissions the major fluxes need to be investigated and the sources of the contamination of municipal treatment plants need to be determined. In this study, five major industrial point sources, two different household areas and the influent and effluent of the corresponding treatment plant (WWTP) were monitored simultaneously at a plant serving 120,000 population equivalents. A paper producing plant was the major BPA contributor to the influent load of the wastewater treatment plant. All the other emissions from point sources, including the two household areas, were considerably lower. The minimum elimination rate in the WTTP could be determined at 78% with an average of 89% of the total BPA-load. For a possible pollution-forecast, or for a comparison between different point sources, emission factors based on COD-emissions were calculated for industrial and household point sources at BPA/COD-ratios between 1.4 x 10(-8) - 125 x 10(-8) and 1.3 x 10(-6) - 6.3 x 10(-6), respectively.

Games between stakeholders and the payment for ecological services: evidence from the Wuxijiang River reservoir area in China

PubMed Central

2018-01-01

A gambling or “game” phenomenon can be observed in the complex relationship between sources and receptors of ecological compensation among multiple stakeholders. This paper investigates the problem of gambling to determine payment amounts, and details a method to estimate the ecological compensation amount related to water resources in the Wuxijiang River reservoir area in China. Public statistics and first-hand data obtained from a field investigation were used as data sources. Estimation of the source and receptor amount of ecological compensation relevant to the water resource being investigated was achieved using the contingent valuation method (CVM). The ecological compensation object and its benefit and gambling for the Wuxijiang River water source area are also analyzed in this paper. According to the results of a CVM survey, the ecological compensation standard for the Wuxijiang River was determined by the CVM, and the amount of compensation was estimated. Fifteen blocks downstream of the Wuxijiang River and 12 blocks in the water source area were used as samples to administer a survey that estimated the willingness to pay (WTP) and the willingness to accept (WTA) the ecological compensation of Wuxijiang River for both nonparametric and parametric estimation. Finally, the theoretical value of the ecological compensation amount was estimated. Without taking other factors into account, the WTP of residents in the Wuxi River water source was 297.48 yuan per year, while the WTAs were 3864.48 yuan per year. The theoretical standard of ecological compensation is 2294.39–2993.81 yuan per year. Under the parameter estimation of other factors, the WTP of residents in the Wuxi River water source area was 528.72 yuan per year, while the WTA was 1514.04 yuan per year. The theoretical standard of ecological compensation is 4076.25–5434.99 yuan per year. The main factors influencing the WTP ecological compensation in the Wuxi River basin are annual income and age. The main factors affecting WTA are gender and attention to the environment, age, marital status, local birth, and location in the main village. PMID:29568707

Patterns and age distribution of ground-water flow to streams

USGS Publications Warehouse

Modica, E.; Reilly, T.E.; Pollock, D.W.

1997-01-01

Simulations of ground-water flow in a generic aquifer system were made to characterize the topology of ground-water flow in the stream subsystem and to evaluate its relation to deeper ground-water flow. The flow models are patterned after hydraulic characteristics of aquifers of the Atlantic Coastal Plain and are based on numerical solutions to three-dimensional, steady-state, unconfined flow. The models were used to evaluate the effects of aquifer horizontal-to-vertical hydraulic conductivity ratios, aquifer thickness, and areal recharge rates on flow in the stream subsystem. A particle tracker was used to determine flow paths in a stream subsystem, to establish the relation between ground-water seepage to points along a simulated stream and its source area of flow, and to determine ground-water residence time in stream subsystems. In a geometrically simple aquifer system with accretion, the source area of flow to streams resembles an elongated ellipse that tapers in the downgradient direction. Increased recharge causes an expansion of the stream subsystem. The source area of flow to the stream expands predominantly toward the stream headwaters. Baseflow gain is also increased along the reach of the stream. A thin aquifer restricts ground-water flow and causes the source area of flow to expand near stream headwaters and also shifts the start-of-flow to the drainage basin divide. Increased aquifer anisotropy causes a lateral expansion of the source area of flow to streams. Ground-water seepage to the stream channel originates both from near- and far-recharge locations. The range in the lengths of flow paths that terminate at a point on a stream increase in the downstream direction. Consequently, the age distribution of ground water that seeps into the stream is skewed progressively older with distance downstream. Base flow ia an integration of ground water with varying age and potentially different water quality, depending on the source within the drainage basin. The quantitative results presented indicate that this integration can have a wide and complex residence time range and source distribution.

Games between stakeholders and the payment for ecological services: evidence from the Wuxijiang River reservoir area in China.

PubMed

Shu, Lin

2018-01-01

A gambling or "game" phenomenon can be observed in the complex relationship between sources and receptors of ecological compensation among multiple stakeholders. This paper investigates the problem of gambling to determine payment amounts, and details a method to estimate the ecological compensation amount related to water resources in the Wuxijiang River reservoir area in China. Public statistics and first-hand data obtained from a field investigation were used as data sources. Estimation of the source and receptor amount of ecological compensation relevant to the water resource being investigated was achieved using the contingent valuation method (CVM). The ecological compensation object and its benefit and gambling for the Wuxijiang River water source area are also analyzed in this paper. According to the results of a CVM survey, the ecological compensation standard for the Wuxijiang River was determined by the CVM, and the amount of compensation was estimated. Fifteen blocks downstream of the Wuxijiang River and 12 blocks in the water source area were used as samples to administer a survey that estimated the willingness to pay (WTP) and the willingness to accept (WTA) the ecological compensation of Wuxijiang River for both nonparametric and parametric estimation. Finally, the theoretical value of the ecological compensation amount was estimated. Without taking other factors into account, the WTP of residents in the Wuxi River water source was 297.48 yuan per year, while the WTAs were 3864.48 yuan per year. The theoretical standard of ecological compensation is 2294.39-2993.81 yuan per year. Under the parameter estimation of other factors, the WTP of residents in the Wuxi River water source area was 528.72 yuan per year, while the WTA was 1514.04 yuan per year. The theoretical standard of ecological compensation is 4076.25-5434.99 yuan per year. The main factors influencing the WTP ecological compensation in the Wuxi River basin are annual income and age. The main factors affecting WTA are gender and attention to the environment, age, marital status, local birth, and location in the main village.

Identifying sediment sources in the sediment TMDL process

USGS Publications Warehouse

Gellis, Allen C.; Fitzpatrick, Faith A.; Schubauer-Berigan, Joseph P.; Landy, R.B.; Gorman Sanisaca, Lillian E.

2015-01-01

Sediment is an important pollutant contributing to aquatic-habitat degradation in many waterways of the United States. This paper discusses the application of sediment budgets in conjunction with sediment fingerprinting as tools to determine the sources of sediment in impaired waterways. These approaches complement monitoring, assessment, and modeling of sediment erosion, transport, and storage in watersheds. Combining the sediment fingerprinting and sediment budget approaches can help determine specific adaptive management plans and techniques applied to targeting hot spots or areas of high erosion.

Heavy metal contamination of surface soil in electronic waste dismantling area: site investigation and source-apportionment analysis.

PubMed

Jinhui Li; Huabo Duan; Pixing Shi

2011-07-01

The dismantling and disposal of electronic waste (e-waste) in developing countries is causing increasing concern because of its impacts on the environment and risks to human health. Heavy-metal concentrations in the surface soils of Guiyu (Guangdong Province, China) were monitored to determine the status of heavy-metal contamination on e-waste dismantling area with a more than 20 years history. Two metalloids and nine metals were selected for investigation. This paper also attempts to compare the data among a variety of e-waste dismantling areas, after reviewing a number of heavy-metal contamination-related studies in such areas in China over the past decade. In addition, source apportionment of heavy metal in the surface soil of these areas has been analysed. Both the MSW open-burning sites probably contained invaluable e-waste and abandoned sites formerly involved in informal recycling activities are the new sources of soil-based environmental pollution in Guiyu. Although printed circuit board waste is thought to be the main source of heavy-metal emissions during e-waste processing, requirement is necessary to soundly manage the plastic separated from e-waste, which mostly contains heavy metals and other toxic substances.

[Research on spatial differentiation of urban stormwater runoff quality by source area monitoring].

PubMed

Li, Li-Qing; Zhu, Ren-Xiao; Guo, Shu-Gang; Yin, Cheng-Qing

2010-12-01

Runoff samples were collected from 14 source areas in Hanyang district during four rain events in an attempt to investigate the spatial differentiation and influencing factors of urban stormwater runoff quality. The outcomes are expected to offer practical guidance in sources control of urban runoff pollution. The results revealed that particle-bound proportion of chemical oxygen demand (COD), total nitrogen (TN), and total phosphorus (TP) in stormwater runoff were 58% +/- 17%, 65% +/- 13% and 92% +/- 6%, respectively. The fractions of ammonia, nitrate and dissolved organic nitrogen were homogeneous in dissolved nitrogen composition. Urban surface function, traffic volume, land use, population density, and street sweeping practice are the main factors determining spatial differentiation of urban surface runoff quality. The highest magnitude of urban stormwater runoff pollution was expected in the old urban residential area, followed by general residential with restaurants, commercial and transport area, new developments and green land. In addition, the magnitude of road stormwater runoff pollution is positively correlated to traffic volume, in the following order: the first trunk road > the second trunk road > minor road. Street sweeping and critical source areas controls should be implemented to mitigate the adverse effects of urban stormwater runoff on receive waters.

Application of multivariate analysis to investigate the trace element contamination in top soil of coal mining district in Jorong, South Kalimantan, Indonesia

NASA Astrophysics Data System (ADS)

Pujiwati, Arie; Nakamura, K.; Watanabe, N.; Komai, T.

2018-02-01

Multivariate analysis is applied to investigate geochemistry of several trace elements in top soils and their relation with the contamination source as the influence of coal mines in Jorong, South Kalimantan. Total concentration of Cd, V, Co, Ni, Cr, Zn, As, Pb, Sb, Cu and Ba was determined in 20 soil samples by the bulk analysis. Pearson correlation is applied to specify the linear correlation among the elements. Principal Component Analysis (PCA) and Cluster Analysis (CA) were applied to observe the classification of trace elements and contamination sources. The results suggest that contamination loading is contributed by Cr, Cu, Ni, Zn, As, and Pb. The elemental loading mostly affects the non-coal mining area, for instances the area near settlement and agricultural land use. Moreover, the contamination source is classified into the areas that are influenced by the coal mining activity, the agricultural types, and the river mixing zone. Multivariate analysis could elucidate the elemental loading and the contamination sources of trace elements in the vicinity of coal mine area.

Analysis of Seismic Moment Tensor and Finite-Source Scaling During EGS Resource Development at The Geysers, CA

NASA Astrophysics Data System (ADS)

Boyd, O. S.; Dreger, D. S.; Gritto, R.

2015-12-01

Enhanced Geothermal Systems (EGS) resource development requires knowledge of subsurface physical parameters to quantify the evolution of fracture networks. We investigate seismicity in the vicinity of the EGS development at The Geysers Prati-32 injection well to determine moment magnitude, focal mechanism, and kinematic finite-source models with the goal of developing a rupture area scaling relationship for the Geysers and specifically for the Prati-32 EGS injection experiment. Thus far we have analyzed moment tensors of M ≥ 2 events, and are developing the capability to analyze the large numbers of events occurring as a result of the fluid injection and to push the analysis to smaller magnitude earthquakes. We have also determined finite-source models for five events ranging in magnitude from M 3.7 to 4.5. The scaling relationship between rupture area and moment magnitude of these events resembles that of a published empirical relationship derived for events from M 4.5 to 8.3. We plan to develop a scaling relationship in which moment magnitude and corner frequency are predictor variables for source rupture area constrained by the finite-source modeling. Inclusion of corner frequency in the empirical scaling relationship is proposed to account for possible variations in stress drop. If successful, we will use this relationship to extrapolate to the large numbers of events in the EGS seismicity cloud to estimate the coseismic fracture density. We will present the moment tensor and corner frequency results for the micro earthquakes, and for select events, finite-source models. Stress drop inferred from corner frequencies and from finite-source modeling will be compared.

Comparison of WindTrax and flux-gradient technique in determining PM10 emission rates from a beef cattle feedlot

USDA-ARS?s Scientific Manuscript database

Several emission estimation methods can be used to determine emission fluxes from ground-level area sources, including open-lot beef cattle feedlots. This research determined PM10 emission fluxes from a commercial cattle feedlot in Kansas using WindTrax, a backward Lagrangian stochastic-based atmosp...

40 CFR Table 1 to Subpart Vvvvvv... - Hazardous Air Pollutants Used To Determine Applicability of Chemical Manufacturing Operations

Code of Federal Regulations, 2010 CFR

2010-07-01

... Determine Applicability of Chemical Manufacturing Operations 1 Table 1 to Subpart VVVVVV of Part 63... Standards for Hazardous Air Pollutants for Chemical Manufacturing Area Sources Pt. 63, Subpt. VVVVVV, Table 1 Table 1 to Subpart VVVVVV of Part 63—Hazardous Air Pollutants Used To Determine Applicability of...

40 CFR Table 1 to Subpart Vvvvvv... - Hazardous Air Pollutants Used To Determine Applicability of Chemical Manufacturing Operations

Code of Federal Regulations, 2013 CFR

2013-07-01

... Determine Applicability of Chemical Manufacturing Operations 1 Table 1 to Subpart VVVVVV of Part 63... Standards for Hazardous Air Pollutants for Chemical Manufacturing Area Sources Pt. 63, Subpt. VVVVVV, Table 1 Table 1 to Subpart VVVVVV of Part 63—Hazardous Air Pollutants Used To Determine Applicability of...

40 CFR Table 1 to Subpart Vvvvvv... - Hazardous Air Pollutants Used To Determine Applicability of Chemical Manufacturing Operations

Code of Federal Regulations, 2014 CFR

2014-07-01

... Determine Applicability of Chemical Manufacturing Operations 1 Table 1 to Subpart VVVVVV of Part 63... Standards for Hazardous Air Pollutants for Chemical Manufacturing Area Sources Pt. 63, Subpt. VVVVVV, Table 1 Table 1 to Subpart VVVVVV of Part 63—Hazardous Air Pollutants Used To Determine Applicability of...

40 CFR Table 1 to Subpart Vvvvvv... - Hazardous Air Pollutants Used To Determine Applicability of Chemical Manufacturing Operations

Code of Federal Regulations, 2011 CFR

2011-07-01

... Determine Applicability of Chemical Manufacturing Operations 1 Table 1 to Subpart VVVVVV of Part 63... Standards for Hazardous Air Pollutants for Chemical Manufacturing Area Sources Pt. 63, Subpt. VVVVVV, Table 1 Table 1 to Subpart VVVVVV of Part 63—Hazardous Air Pollutants Used To Determine Applicability of...

40 CFR Table 1 to Subpart Vvvvvv... - Hazardous Air Pollutants Used To Determine Applicability of Chemical Manufacturing Operations

Code of Federal Regulations, 2012 CFR

2012-07-01

... Determine Applicability of Chemical Manufacturing Operations 1 Table 1 to Subpart VVVVVV of Part 63... Standards for Hazardous Air Pollutants for Chemical Manufacturing Area Sources Pt. 63, Subpt. VVVVVV, Table 1 Table 1 to Subpart VVVVVV of Part 63—Hazardous Air Pollutants Used To Determine Applicability of...

Improved aethalometer

DOEpatents

Hansen, A.D.

1988-01-25

An improved aethalometer having a single light source and a single light detector and two light paths from the light source to the light detector. A quartz fiber filter is inserted in the device, the filter having a collection area in one light path and a reference area in the other light path. A gas flow path through the aethalometer housing allows ambient air to flow through the collection area of the filter so that aerosol particles can be collected on the filter. A rotating disk with an opening therethrough allows light for the light source to pass alternately through the two light paths. The voltage output of the detector is applied to a VCO and the VCO pulses for light transmission separately through the two light paths, are counted and compared to determine the absorption coefficient of the collected aerosol particles. 5 figs.

Estimating small amplitude tremor sources

NASA Astrophysics Data System (ADS)

Katakami, S.; Ito, Y.; Ohta, K.

2017-12-01

Various types of slow earthquakes have been recently observed at both the updip and downdip edges of the coseismic slip areas [Obara and Kato, 2016]. Frequent occurrence of slow earthquakes may help us to reveal the physics underlying megathrust events as useful analogs. Maeda and Obara [2009] estimated spatiotemporal distribution of seismic energy radiation from low-frequency tremors. They applied their method to only the tremors, whose hypocenters had been decided with multiple station method. However, recently Katakami et al. (2016) identified a lot of continuous tremors with small amplitude that were not recorded multiple stations. These small events should be important to reveal the whole slow earthquake activity and to understand strain condition around a plate boundary in subduction zones. First, we apply the modified frequency scanning method (mFSM) at a single station to NIED Hi-net data in the southwestern Japan to understand whole tremor activity which were included weak signal tremors. Second, we developed a method to identify the tremor source area by using the difference of apparent tremor energy at each station by mFSM. We estimated the apparent source tremor energy after correcting both site amplification factor and geometrical spreading. Finally we calculate a tremor source area if the difference of apparent tremor energy between each pair of sites is the smallest. We checked a validity of this analysis by using only tremors which were already detected by envelope correlation method [Idehara et al., 2014]. We calculated the average amplitude as apparent tremor energy in 5 minutes window after occurring tremor at each station. Our results almost consistent to hypocenters which were determined the envelope correlation method. We successfully determined apparent tremor source areas of weak continuous tremors after estimating possible tremor occurrence time windows by using mFSM.

Locations with High Reliance on Private Wells: Not Always Where You Think They Are

EPA Science Inventory

For developing contaminant management strategies and protecting drinking water supplies, the locations of areas with reliance on private domestic wells (PDWs) and their relationship to contaminant sources need to be determined. From 1960 to 1990, a key resource in determining are...

Slip distribution of the 1952 Tokachi-Oki earthquake (M 8.1) along the Kuril Trench deduced from tsunami waveform inversion

USGS Publications Warehouse

Hirata, K.; Geist, E.; Satake, K.; Tanioka, Y.; Yamaki, S.

2003-01-01

We inverted 13 tsunami waveforms recorded in Japan to estimate the slip distribution of the 1952 Tokachi-Oki earthquake (M 8.1), which occurred southeast off Hokkaido along the southern Kuril subduction zone. The previously estimated source area determined from tsunami travel times [Hatori, 1973] did not coincide with the observed aftershock distribution. Our results show that a large amount of slip occurred in the aftershock area east of Hatori's tsunami source area, suggesting that a portion of the interplate thrust near the trench was ruptured by the main shock. We also found more than 5 m of slip along the deeper part of the seismogenic interface, just below the central part of Hatori's tsunami source area. This region, which also has the largest stress drop during the main shock, had few aftershocks. Large tsunami heights on the eastern Hokkaido coast are better explained by the heterogeneous slip model than previous uniform-slip fault models. The total seismic moment is estimated to be 1.87 ?? 1021 N m, giving a moment magnitude of Mw = 8.1. The revised tsunami source area is estimated to be 25.2 ?? 103 km2, ???3 times larger than the previous tsunami source area. Out of four large earthquakes with M ??? 7 that subsequently occurred in and around the rupture area of the 1952 event, three were at the edges of regions with relatively small amount of slip. We also found that a subducted seamount near the edge of the rupture area possibly impeded slip along the plate interface.

Avoiding Clean Air Act Enforcement Actions

DTIC Science & Technology

1994-06-01

process or common-source permits (for instance, all boilers or all sources within a defined area on one per- mit); or separate permits for every source of... boilers ; and explosive produc- tion processes. The limitations on NO. emissions may become more stringent if it is determined that these emissions...ISC = Infornmtbon Systems C~r;, INSCOM w; HSC m HhO Sewims Com- rand; FORSCOM - Forces Command; ARNG a Army Natonal Guwd; AMC = Army Maet Command

Effects of planting density and genotype on loblolly pine stands growing in the mountains of southeastern Oklahoma

Treesearch

Rodney E. Will; Thomas C. Hennessey; Thomas B. Lynch; Robert Heinemann; Randal Holeman; Dennis Wilson; Keith Anderson; Gregory Campbell

2013-01-01

We determined the effects of planting density (4- by 4-, 6- by 6-, 8- by 8-, and 10- by 10-foot spacing) on stand-level height, diameter at breast height, stem volume, basal area, and periodic annual increment for two loblolly pine (Pinus taeda L.) seed sources. Seed sources for the 25-year-old stands were a North Carolina seed source (NCC 8-01) and...

Beyond the Nation-State: A Process for Determining the Security Strategy for the Integrated United Continent of Europe

DTIC Science & Technology

1990-05-01

shrinking water supply, and shrinking fuel reserves. As these challenges multiply, the source of solutions becomes difficult to identify. A cooperative ... movement of the people through political channels seems to be the emerging source. 5 CHAPTER II IDENTIFYING NEW THREAT AREAS What does all this have to do

Understanding Hydrological Processes in Variable Source Areas in the Glaciated Northeastern US Watersheds under Variable Climate Conditions

NASA Astrophysics Data System (ADS)

Steenhuis, T. S.; Azzaino, Z.; Hoang, L.; Pacenka, S.; Worqlul, A. W.; Mukundan, R.; Stoof, C.; Owens, E. M.; Richards, B. K.

2017-12-01

The New York City source watersheds in the Catskill Mountains' humid, temperate climate has long-term hydrological and water quality monitoring data It is one of the few catchments where implementation of source and landscape management practices has led to decreased phosphorus concentration in the receiving surface waters. One of the reasons is that landscape measures correctly targeted the saturated variable source runoff areas (VSA) in the valley bottoms as the location where most of the runoff and other nonpoint pollutants originated. Measures targeting these areas were instrumental in lowering phosphorus concentration. Further improvements in water quality can be made based on a better understanding of the flow processes and water table fluctuations in the VSA. For that reason, we instrumented a self-contained upland variable source watershed with a landscape characteristic of a soil underlain by glacial till at shallow depth similar to the Catskill watersheds. In this presentation, we will discuss our experimental findings and present a mathematical model. Variable source areas have a small slope making gravity the driving force for the flow, greatly simplifying the simulation of the flow processes. The experimental data and the model simulations agreed for both outflow and water table fluctuations. We found that while the flows to the outlet were similar throughout the year, the discharge of the VSA varies greatly. This was due to transpiration by the plants which became active when soil temperatures were above 10oC. We found that shortly after the temperature increased above 10oC the baseflow stopped and only surface runoff occurred when rainstorms exceeded the storage capacity of the soil in at least a portion of the variable source area. Since plant growth in the variable source area was a major variable determining the base flow behavior, changes in temperature in the future - affecting the duration of the growing season - will affect baseflow and related transport of nutrient and other chemicals many times more than small temperature related increases in potential evaporation rate. This in turn will directly change the water availability and pollutant transport in the many surface source watersheds with variable source area hydrology.

Isolation of Vibrio cholerae Serotype Ogawa from a Florida Estuary

PubMed Central

Motes, M. L.; Zywno, S. R.; DePaola, A.; Becker, R. E.; Presnell, M. W.

1983-01-01

Vibrio cholerae serotype Ogawa was recently isolated from the estuarine waters of Apalachicola Bay, Fla., in areas that are subject to consistent fecal contamination and in areas that are remote from any apparent source of contamination. The significance of these organisms in the environment has not been determined. PMID:6824323

Commercial Contract Training, Marine Corps Area VOTEC Support Center (AVSC) Guidelines. Final Report.

ERIC Educational Resources Information Center

Copeland, D. R.; And Others

The report provides a description of the Phase II findings of a two-phase study to determine if certain Marine Corps skill training requirements could be satisfied through contract with qualified commercial sources. It demonstrates the utility of the commercial contract training concept and contains information useful to Area VOTEC…

Two whisker motor areas in the rat cortex: evidence from thalamocortical connections.

PubMed

Mohammed, Hisham; Jain, Neeraj

2014-02-15

In primates, the motor cortex consists of at least seven different areas, which are involved in movement planning, coordination, initiation, and execution. However, for rats, only the primary motor cortex has been well described. A rostrally located second motor area has been proposed, but its extent, organization, and even definitive existence remain uncertain. Only a rostral forelimb area (RFA) has been definitively described, besides few reports of a rostral hindlimb area. We have previously proposed existence of a second whisker area, which we termed the rostral whisker area (RWA), based on its differential response to intracortical microstimulation compared with the caudal whisker area (CWA) in animals under deep anesthesia (Tandon et al. [2008] Eur J Neurosci 27:228). To establish that RWA is distinct from the caudally contiguous CWA, we determined sources of thalamic inputs to the two proposed whisker areas. Sources of inputs to RFA, caudal forelimb area (CFA), and caudal hindlimb region were determined for comparison. The results show that RWA and CWA can be distinguished based on differences in their thalamic inputs. RWA receives major projections from mediodorsal and ventromedial nuclei, whereas the major projections to CWA are from the ventral anterior, ventrolateral, and posterior nuclei. Moreover, the thalamic nuclei that provide major inputs to RWA are the same as for RFA, and the nuclei projecting to CWA are same as for CFA. The results suggest that rats have a second rostrally located motor area with RWA and RFA as its constituents. Copyright © 2013 Wiley Periodicals, Inc.

Contamination levels, toxicity profiles, and emission sources of polycyclic aromatic hydrocarbons (PAHs) in the soils of an emerging industrial town and its environs in the Southeastern Nigeria.

PubMed

Ofomatah, Anthony C; Okoye, Chukwuma O B

2017-11-09

Polycyclic aromatic hydrocarbon (PAH) concentrations in Nnewi and its environs were determined. Soil samples were extracted by sonication using hexane:dichloromethane (3:1) mixture and determined by gas chromatography-flame ionization detection. The total PAHs concentrations (μg/kg) were 16.681 to 46.815, being three orders of magnitude lower than the maximum permissible level recommended by the Agency for Toxic Substances and Disease Registry (ATSDR). These concentrations followed this order: industrial ˃ farmlands ˃ commercial ˃ residential. Industrialized areas showed higher concentrations (p ˂ 0.05) than the other areas. Diagnostic ratios show that the major source of PAHs was the open burning of industrial and agricultural wastes, as shown by the occurrence of highest concentrations in the industrial areas, followed by agricultural areas. Benzo[a]pyrene equivalent values showed non-pollution and very low toxicity. Nevertheless, it was clear that industrialization has had some impact on the PAHs levels in soils and the total environment in this area and could be problematic with time, except with proper environmental management.

[Urban heat island effect based on urban heat island source and sink indices in Shenyang, Northeast China].

PubMed

Li, Li-Guang; Xu, Shen-Lai; Wang, Hong-Bo; Zhao, Zi-Qi; Cai, Fu; Wu, Jin-Wen; Chen, Peng-Shi; Zhang, Yu-Shu

2013-12-01

Based on the remote images in 2001 and 2010, the source and sink areas of urban heat island (UHI) in Shenyang City, Northeast China were determined by GIS technique. The effect of urban regional landscape pattern on UHI effect was assessed with land surface temperature (LST), area rate index (CI) of the source and sink areas and intensity index (LI) of heat island. The results indicated that the land use type changed significantly from 2001 to 2010, which significantly changed the source and sink areas of UHI, especially in the second and third circle regions. The source and sink areas were 94.3% and 5.7% in the first circle region, 64.0% and 36.0% in the third circle region in 2001, while they were 93.4% and 6.6%, 70.2% and 29.8% in 2010, respectively. It suggested that the land use pattern extended by a round shape in Shenyang led to the corresponding UHI pattern. The LST in the study area tended to decrease from the first circle region to the third. The UHI intensity was characterized with a single center in 2001 and with several centers in 2010, and the grade of UHI intensity was in a decreasing trend from 2001 to 2010. The absolute value of CI increased from the first circle region to the third, and the L1 was close to 1, suggesting the change in land use pattern had no significant influence on UHI in Shenyang.

Uranium content of ground and surface waters in western Kansas, eastern Colorado, and the Oklahoma Panhande

USGS Publications Warehouse

Landis, E.R.

1956-01-01

and in some parts of the report area, such as the Cimarron River area of westernmost Oklahoma and northeastern New Mexico, and the Rule Creek area in Bent and Las Animas Counties, Colo. , most, or all, of the water samples collected contain relatively large amounts of uranium. Further exploration to determine the source of the uranium in the water from these rock units and areas may be worthwhile.

Identification of sources and seasonal variability of organic matter in Lake Sihwa and surrounding inland creeks, South Korea.

PubMed

Lee, Yeonjung; Hong, Seongjin; Kim, Min-Seob; Kim, Dahae; Choi, Bo-Hyung; Hur, Jin; Khim, Jong Seong; Shin, Kyung-Hoon

2017-06-01

Coastal areas are subjected to significant allochthonous organic matter deposits from surrounding areas; however, limited information is available on the source and delivery of this organic matter. In this study, to assess seasonal changes in the sources of organic matter in Lake Sihwa (Korea), biodegradability, fluorescence property, and stable isotopic compositions (carbon, nitrogen, and sulfur) of the organic matter were determined. Water samples were collected from the inner lake (n = 9) and inland creeks (n = 10) in five separate events, from November 2012 to October 2013. Organic matter originating from rural, urban, and industrial areas was examined as the potential sources. The organic matter contents and biodegradability in the industrial area were the highest, whereas low concentrations and poor biodegradability of organic matter were found in the rural area, and moderate properties were observed in the urban area. In Lake Sihwa, a large concentration of total organic matter and enhanced biodegradability were observed during March and August. However, main source of organic matter differed between the sampling events. The largest contribution of organic matter, deriving from marine phytoplankton, was found in March. On the other hand, in August, the organic matter originating from the industrial area, which is characterized by high levels of heavy metals and persistent organic pollutants, was significantly increased. Our results could be useful to enhance the management of water bodies aimed at reducing the organic matter concentrations and improving the water quality of Lake Sihwa, and even that of the Yellow Sea. Copyright © 2017 Elsevier Ltd. All rights reserved.

40 CFR 146.22 - Construction requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Director may consider information on: (i) Nature of formation fluids; (ii) Lithology of injection and... underground sources of drinking water in areas where the lithology has not been determined: (A) Electric and...

40 CFR 146.22 - Construction requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Director may consider information on: (i) Nature of formation fluids; (ii) Lithology of injection and... underground sources of drinking water in areas where the lithology has not been determined: (A) Electric and...

40 CFR 146.22 - Construction requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Director may consider information on: (i) Nature of formation fluids; (ii) Lithology of injection and... underground sources of drinking water in areas where the lithology has not been determined: (A) Electric and...

30 CFR 56.6600 - Loading practices.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Electricity § 56.6600 Loading practices. If extraneous electricity is suspected in an area where electric... levels of extraneous electricity are found, the source shall be determined and no loading shall take...

30 CFR 56.6600 - Loading practices.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Electricity § 56.6600 Loading practices. If extraneous electricity is suspected in an area where electric... levels of extraneous electricity are found, the source shall be determined and no loading shall take...

30 CFR 56.6600 - Loading practices.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Electricity § 56.6600 Loading practices. If extraneous electricity is suspected in an area where electric... levels of extraneous electricity are found, the source shall be determined and no loading shall take...

30 CFR 56.6600 - Loading practices.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Electricity § 56.6600 Loading practices. If extraneous electricity is suspected in an area where electric... levels of extraneous electricity are found, the source shall be determined and no loading shall take...

30 CFR 56.6600 - Loading practices.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Electricity § 56.6600 Loading practices. If extraneous electricity is suspected in an area where electric... levels of extraneous electricity are found, the source shall be determined and no loading shall take...

Oil spill contamination probability in the southeastern Levantine basin.

PubMed

Goldman, Ron; Biton, Eli; Brokovich, Eran; Kark, Salit; Levin, Noam

2015-02-15

Recent gas discoveries in the eastern Mediterranean Sea led to multiple operations with substantial economic interest, and with them there is a risk of oil spills and their potential environmental impacts. To examine the potential spatial distribution of this threat, we created seasonal maps of the probability of oil spill pollution reaching an area in the Israeli coastal and exclusive economic zones, given knowledge of its initial sources. We performed simulations of virtual oil spills using realistic atmospheric and oceanic conditions. The resulting maps show dominance of the alongshore northerly current, which causes the high probability areas to be stretched parallel to the coast, increasing contamination probability downstream of source points. The seasonal westerly wind forcing determines how wide the high probability areas are, and may also restrict these to a small coastal region near source points. Seasonal variability in probability distribution, oil state, and pollution time is also discussed. Copyright © 2014 Elsevier Ltd. All rights reserved.

Source Distribution Method for Unsteady One-Dimensional Flows With Small Mass, Momentum, and Heat Addition and Small Area Variation

NASA Technical Reports Server (NTRS)

Mirels, Harold

1959-01-01

A source distribution method is presented for obtaining flow perturbations due to small unsteady area variations, mass, momentum, and heat additions in a basic uniform (or piecewise uniform) one-dimensional flow. First, the perturbations due to an elemental area variation, mass, momentum, and heat addition are found. The general solution is then represented by a spatial and temporal distribution of these elemental (source) solutions. Emphasis is placed on discussing the physical nature of the flow phenomena. The method is illustrated by several examples. These include the determination of perturbations in basic flows consisting of (1) a shock propagating through a nonuniform tube, (2) a constant-velocity piston driving a shock, (3) ideal shock-tube flows, and (4) deflagrations initiated at a closed end. The method is particularly applicable for finding the perturbations due to relatively thin wall boundary layers.

Feeding profile of Mepraia spinolai, a sylvatic vector of Chagas disease in Chile.

PubMed

Chacón, F; Bacigalupo, A; Quiroga, J F; Ferreira, A; Cattan, P E; Ramírez-Toloza, G

2016-10-01

American trypanosomiasis is a chronic disease transmitted mainly by vectors. The hematophagous triatomine vectors transmit Trypanosoma cruzi to a wide variety of mammals, which usually are their food source. This study determined the feeding profile of Mepraia spinolai, a sylvatic triatomine vector, present in endemic areas of Chile. Vectors were captured in the north-central area of Chile. Samples of intestinal contents were analyzed by an Enzyme-linked immunosorbent assay (ELISA) that identifies and discriminates the presence of serum antigens from Homo sapiens and nine animal species (Canis familiaris, Felis catus, Capra hircus, Mus musculus, Gallus gallus, Octodon degus, Thylamys elegans, Phyllotis darwini and Oryctolagus cuniculus). Our data indicate the most frequent feeding source in this area was P. darwini, followed by O. degus, O. cuniculus, M. musculus, G. gallus, T. elegans, C. familiaris, F. catus and C. hircus. Mixed food sources were also identified. Copyright © 2016 Elsevier B.V. All rights reserved.

Noise from high speed maglev systems: Noise sources, noise criteria, preliminary design guidelines for noise control, recommendations for acoustical test facility for maglev research. Final report, July 1991-October 1992

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hanson, C.E.; Abbot, P.; Dyer, I.

1993-01-01

Noise levels from magnetically-levitated trains (maglev) at very high speed may be high enough to cause environmental noise impact in residential areas. Aeroacoustic sources dominate the sound at high speeds and guideway vibrations generate noticeable sound at low speed. In addition to high noise levels, the startle effect as a result of sudden onset of sound from a rapidly moving nearby maglev vehicle may lead to increased annoyance to neighbors of a maglev system. The report provides a base for determining the noise consequences and potential mitigation for a high speed maglev system in populated areas of the United States.more » Four areas are included in the study: (1) definition of noise sources; (2) development of noise criteria; (3) development of design guidelines; and (4) recommendations for a noise testing facility.« less

The effect of nitrogen loading on on-site system design: a model for determining land application area size.

PubMed

McCardell, A; Davison, L; Edwards, A

2005-01-01

Designers of on-site wastewater management systems have six opportunities to remove pollutants of concern from the aqueous waste stream before it reaches ground or surface waters. These opportunities occur at source, at point of collection (primary treatment), secondary treatment, tertiary treatment, land application and buffers. This paper presents a computer based model for the sizing of on-site system land application areas applicable to the Lismore area in Northern New South Wales, a region of high rainfall. Inputs to the model include daily climatic data, soil type, number of people loading the system and size of housing allotment. Constraints include allowable phosphorus export, nitrogen export and hydraulic percolation. In the Lismore area nitrogen is the nutrient of most concern. In areas close to environmentally sensitive waterways, and in dense developments, the allowable annual nitrogen export becomes the main factor determining the land application area size. The model offers system designers the opportunity to test various combinations of nitrogen attenuation strategies (source control, secondary treatment) in order to create a solution which offers an acceptable nitrogen export rate while meeting the client's household and financial needs. The model runs on an Excel spreadsheet and has been developed by Lismore City Council.

Assessment of hydrogeologic terrains, well-construction characteristics, groundwater hydraulics, and water-quality and microbial data for determination of surface-water-influenced groundwater supplies in West Virginia

USGS Publications Warehouse

Kozar, Mark D.; Paybins, Katherine S.

2016-08-30

Groundwater public-supply systems in areas of high intrinsic susceptibility and with a large number of potential contaminant sources within the recharge or source-water-protection area of individual wells or well fields are potentially vulnerable to contamination and probably warrant further evaluation as potential SWIGS. However, measures can be taken to educate the local population and initiate safety protocols and protective strategies to appropriately manage contaminant sources to prevent release of contaminants to the aquifer, therefore, reducing vulnerability of these systems to contamination. However, each public groundwater supply source needs to be assessed on an individual basis. Data presented in this report can be used to categorize and prioritize wells and springs that have a high potential for intrinsic susceptibility or vulnerability to contamination.

Plasma diagnosis as a tool for the determination of the parameters of electron beam evaporation and sources of ionization

NASA Astrophysics Data System (ADS)

Mukherjee, Jaya; Dileep Kumar, V.; Yadav, S. P.; Barnwal, Tripti A.; Dikshit, Biswaranjan

2016-07-01

The atomic vapor generated by electron beam heating is partially ionized due to atom-atom collisions (Saha ionization) and electron impact ionization, which depend upon the source temperature and area of evaporation as compared to the area of electron beam bombardment on the target. When electron beam evaporation is carried out by inserting the target inside an insulating liner to reduce conductive heat loss, it is expected that the area of evaporation becomes significantly more than the area of electron beam bombardment on the target, resulting in reduced electron impact ionization. To assess this effect and to quantify the parameters of evaporation, such as temperature and area of evaporation, we have carried out experiments using zirconium, tin and aluminum as a target. By measuring the ion content using a Langmuir probe, in addition to measuring the atomic vapor flux at a specific height, and by combining the experimental data with theoretical expressions, we have established a method for simultaneously inferring the source temperature, evaporation area and ion fraction. This assumes significance because the temperature cannot be reliably measured by an optical pyrometer due to the wavelength dependent source emissivity and reflectivity of thin film mirrors. In addition, it also cannot be inferred from only the atomic flux data at a certain height as the area of evaporation is unknown (it can be much more than the area of electron bombardment, especially when the target is placed in a liner). Finally, the reason for the lower observed electron temperatures of the plasma for all the three cases is found to be the energy loss due to electron impact excitation of the atomic vapor during its expansion from the source.

Integral emission factors for methane determined using urban flux measurements and local-scale inverse models

NASA Astrophysics Data System (ADS)

Christen, Andreas; Johnson, Mark; Molodovskaya, Marina; Ketler, Rick; Nesic, Zoran; Crawford, Ben; Giometto, Marco; van der Laan, Mike

2013-04-01

The most important long-lived greenhouse gas (LLGHG) emitted during combustion of fuels is carbon dioxide (CO2), however also traces of the LLGHGs methane (CH4) and nitrous oxide (N2O) are released, the quantities of which depend largely on the conditions of the combustion process. Emission factors determine the mass of LLGHGs emitted per energy used (or kilometre driven for cars) and are key inputs for bottom-up emission modelling. Emission factors for CH4 are typically determined in the laboratory or on a test stand for a given combustion system using a small number of samples (vehicles, furnaces), yet associated with larger uncertainties when scaled to entire fleets. We propose an alternative, different approach - Can integrated emission factors be independently determined using direct micrometeorological flux measurements over an urban surface? If so, do emission factors determined from flux measurements (top-down) agree with up-scaled emission factors of relevant combustion systems (heating, vehicles) in the source area of the flux measurement? Direct flux measurements of CH4 were carried out between February and May, 2012 over a relatively densely populated, urban surface in Vancouver, Canada by means of eddy covariance (EC). The EC-system consisted of an ultrasonic anemometer (CSAT-3, Campbell Scientific Inc.) and two open-path infrared gas analyzers (Li7500 and Li7700, Licor Inc.) on a tower at 30m above the surface. The source area of the EC system is characterised by a relative homogeneous morphometry (5.3m average building height), but spatially and temporally varying emission sources, including two major intersecting arterial roads (70.000 cars drive through the 50% source area per day) and seasonal heating in predominantly single-family houses (natural gas). An inverse dispersion model (turbulent source area model), validated against large eddy simulations (LES) of the urban roughness sublayer, allows the determination of the spatial area that contributes to each measurement interval (30 min), which varies with wind direction and stability. A detailed geographic information system of the urban surface combined with traffic counts and building energy models makes it possible to statistically relate fluxes to vehicle density (km driven) and buildings (gas heated volume) - and ultimately quantify the contribution of space heating, transport sector and fugitive emissions to the total emitted CH4 from an urban environment. The measured fluxes of CH4 over the selected urban environment averaged to 22.8 mg CH4 m-2 day-1 during the study period. Compared with the simultaneously measured CO2 emissions, the contribution of CH4, however, accounts for only about 3% of the total LLGHG emissions from this particular urban surface. Traffic contributed 8.8 mg CH4 m-2 day-1, equivalent to 39% of the total CH4 flux. The determined emission factor for the typical fleet composition is 0.062 g CH4 per km driven which is higher than upscaled fleet emission factors (EPA) by a factor of two. This discrepancy can be partially explained through the slower city traffic with frequent idling (traffic congestion), fleet composition and cold starts. Emissions of CH4 by domestic space heating (55% of the total CH4 flux or 12.7 mg CH4 m-2 day-1) are also higher than estimated from upscaled emission factors. There is no evidence of substantial unknown sources such as soil processes, combustion of wood, and leakages from gas distribution pipes (residual: 6% or 1.3 mg CH4 m-2 day-1). The presented study is among the first direct measurements of CH4 emissions over an urban surface and demonstrates that flux measurements of greenhouse gases can be used to determine sources and emission factors in complex urban situations.

Principle component analysis to separate deformation signals from multiple sources during a 2015 intrusive sequence at Kīlauea Volcano

NASA Astrophysics Data System (ADS)

Johanson, I. A.; Miklius, A.; Poland, M. P.

2016-12-01

A sequence of magmatic events in April-May 2015 at Kīlauea Volcano produced a complex deformation pattern that can be described by multiple deforming sources, active simultaneously. The 2015 intrusive sequence began with inflation in the volcano's summit caldera near Halema`uma`u (HMM) Crater, which continued over a few weeks, followed by rapid deflation of the HMM source and inflation of a source in the south caldera region during the next few days. In Kīlauea Volcano's summit area, multiple deformation centers are active at varying times, and all contribute to the overall pattern observed with GPS, tiltmeters, and InSAR. Isolating the contribution of different signals related to each source is a challenge and complicates the determination of optimal source geometry for the underlying magma bodies. We used principle component analysis of continuous GPS time series from the 2015 intrusion sequence to determine three basis vectors which together account for 83% of the variance in the data set. The three basis vectors are non-orthogonal and not strictly the principle components of the data set. In addition to separating deformation sources in the continuous GPS data, the basis vectors provide a means to scale the contribution of each source in a given interferogram. This provides an additional constraint in a joint model of GPS and InSAR data (COSMO-SkyMed and Sentinel-1A) to determine source geometry. The first basis vector corresponds with inflation in the south caldera region, an area long recognized as the location of a long-term storage reservoir. The second vector represents deformation of the HMM source, which is in the same location as a previously modeled shallow reservoir, however InSAR data suggest a more complicated source. Preliminary modeling of the deformation attributed to the third basis vector shows that it is consistent with inflation of a steeply dipping ellipsoid centered below Keanakāko`i crater, southeast of HMM. Keanakāko`i crater is the locus of a known, intermittently active deformation source, which was not previously recognized to have been active during the 2015 event.

The Associations between Health Literacy, Reasons for Seeking Health Information, and Information Sources Utilized by Taiwanese Adults

ERIC Educational Resources Information Center

Wei, Mi-Hsiu

2014-01-01

Objective: To determine the associations between health literacy, the reasons for seeking health information, and the information sources utilized by Taiwanese adults. Method: A cross-sectional survey of 752 adults residing in rural and urban areas of Taiwan was conducted via questionnaires. Chi-squared tests and logistic regression were used for…

Defining Primary Care Shortage Areas: Do GIS-based Measures Yield Different Results?

PubMed

Daly, Michael R; Mellor, Jennifer M; Millones, Marco

2018-02-12

To examine whether geographic information systems (GIS)-based physician-to-population ratios (PPRs) yield determinations of geographic primary care shortage areas that differ from those based on bounded-area PPRs like those used in the Health Professional Shortage Area (HPSA) designation process. We used geocoded data on primary care physician (PCP) locations and census block population counts from 1 US state to construct 2 shortage area indicators. The first is a bounded-area shortage indicator defined without GIS methods; the second is a GIS-based measure that measures the populations' spatial proximity to PCP locations. We examined agreement and disagreement between bounded shortage areas and GIS-based shortage areas. Bounded shortage area indicators and GIS-based shortage area indicators agree for the census blocks where the vast majority of our study populations reside. Specifically, 95% and 98% of the populations in our full and urban samples, respectively, reside in census blocks where the 2 indicators agree. Although agreement is generally high in rural areas (ie, 87% of the rural population reside in census blocks where the 2 indicators agree), agreement is significantly lower compared to urban areas. One source of disagreement suggests that bounded-area measures may "overlook" some shortages in rural areas; however, other aspects of the HPSA designation process likely mitigate this concern. Another source of disagreement arises from the border-crossing problem, and it is more prevalent. The GIS-based PPRs we employed would yield shortage area determinations that are similar to those based on bounded-area PPRs defined for Primary Care Service Areas. Disagreement rates were lower than previous studies have found. © 2018 National Rural Health Association.

Groundwater monitoring plan for the Missouri River alluvial aquifer in the vicinity of the City of Independence, Missouri, well field

USGS Publications Warehouse

Wilkison, Donald H.

2012-01-01

Source contributions to monitoring and supply wells, contributing recharge areas, groundwater travel times, and current (2012) understanding of alluvial water quality were used to develop a groundwater monitoring plan for the Missouri River alluvial aquifer in the vicinity of the City of Independence, Missouri well field. The plan was designed to evaluate long-term alluvial water quality and assess potential changes in, and threats to, well-field water quality. Source contributions were determined from an existing groundwater flow model in conjunction with particle-tracking analysis and verified with water-quality data collected from 1997 through 2010 from a network of 68 monitoring wells. Three conjunctive factors - well-field pumpage, Missouri River discharge, and aquifer recharge - largely determined groundwater flow and, therefore, source contributions. The predominant source of groundwater to most monitoring wells and supply wells is the Missouri River, and this was reflected, to some extent, in alluvial water quality. To provide an estimate of the maximum potential lead time available for remedial action, monitoring wells where groundwater travel times from the contributing recharge areas are less than 2 years and predominately singular sources (such as the Missouri River or the land surface) were selected for annual sampling. The sample interval of the remaining wells, which have varying travel times and intermediate mixtures of river and land-surface contributions, were staggered on a 2-, 3-, or 4-year rotation. This was done to provide data from similar contributing areas and account for inherent aquifer variability yet minimize sample redundancy.

Development of a (147)Pm source for beta-backscatter thickness gauge applications.

PubMed

Kumar, Manoj; Udhayakumar, J; Nuwad, J; Shukla, Rakesh; Pillai, C G S; Dash, Ashutosh; Venkatesh, Meera

2011-03-01

This paper describes a method for the preparation of (147)Pm sources, utilized in the determination of graphite coating thickness on the inner surface of the zircaloy cladding tube of nuclear fuels. (147)Pm was adsorbed on a limited surface area [1.5mm (ϕ)×2mm (l)] of a cylindrical aluminum rod [1.5mm (ϕ)×10mm (l)]. In brief, the selected tip area [1.5mm (ϕ)×2mm (l)] was anodized at a current density of 15mA/cm(2) at 15°C in 3M·H(2)SO(4) for 2h followed by immersion of this area in 10μL of (147)Pm solution containing 37MBq (1mCi) of activity at pH 6.0 for 24h. The radioactive area was subsequently covered with a thin layer of Polymethyl Methacrylate (PMMA) to prevent leaching of (147)Pm from the source. The quantity of incorporated (147)Pm activity was assayed in a calibrated ion chamber. Quality control tests were carried out to ensure nonleachability, uniform distribution of activity and stability of the sources. Copyright © 2010 Elsevier Ltd. All rights reserved.

Exploring the uncertainty in attributing sediment contributions in fingerprinting studies due to uncertainty in determining element concentrations in source areas.

NASA Astrophysics Data System (ADS)

Gomez, Jose Alfonso; Owens, Phillip N.; Koiter, Alex J.; Lobb, David

2016-04-01

One of the major sources of uncertainty in attributing sediment sources in fingerprinting studies is the uncertainty in determining the concentrations of the elements used in the mixing model due to the variability of the concentrations of these elements in the source materials (e.g., Kraushaar et al., 2015). The uncertainty in determining the "true" concentration of a given element in each one of the source areas depends on several factors, among them the spatial variability of that element, the sampling procedure and sampling density. Researchers have limited control over these factors, and usually sampling density tends to be sparse, limited by time and the resources available. Monte Carlo analysis has been used regularly in fingerprinting studies to explore the probable solutions within the measured variability of the elements in the source areas, providing an appraisal of the probability of the different solutions (e.g., Collins et al., 2012). This problem can be considered analogous to the propagation of uncertainty in hydrologic models due to uncertainty in the determination of the values of the model parameters, and there are many examples of Monte Carlo analysis of this uncertainty (e.g., Freeze, 1980; Gómez et al., 2001). Some of these model analyses rely on the simulation of "virtual" situations that were calibrated from parameter values found in the literature, with the purpose of providing insight about the response of the model to different configurations of input parameters. This approach - evaluating the answer for a "virtual" problem whose solution could be known in advance - might be useful in evaluating the propagation of uncertainty in mixing models in sediment fingerprinting studies. In this communication, we present the preliminary results of an on-going study evaluating the effect of variability of element concentrations in source materials, sampling density, and the number of elements included in the mixing models. For this study a virtual catchment was constructed, composed by three sub-catchments each of 500 x 500 m size. We assumed that there was no selectivity in sediment detachment or transport. A numerical excercise was performed considering these variables: 1) variability of element concentration: three levels with CVs of 20 %, 50 % and 80 %; 2) sampling density: 10, 25 and 50 "samples" per sub-catchment and element; and 3) number of elements included in the mixing model: two (determined), and five (overdetermined). This resulted in a total of 18 (3 x 3 x 2) possible combinations. The five fingerprinting elements considered in the study were: C, N, 40K, Al and Pavail, and their average values, taken from the literature, were: sub-catchment 1: 4.0 %, 0.35 %, 0.50 ppm, 5.0 ppm, 1.42 ppm, respectively; sub-catchment 2: 2.0 %, 0.18 %, 0.20 ppm, 10.0 ppm, 0.20 ppm, respectively; and sub-catchment 3: 1.0 %, 0.06 %, 1.0 ppm, 16.0 ppm, 7.8 ppm, respectively. For each sub-catchment, three maps of the spatial distribution of each element was generated using the random generator of Mejia and Rodriguez-Iturbe (1974) as described in Freeze (1980), using the average value and the three different CVs defined above. Each map for each source area and property was generated for a 100 x 100 square grid, each grid cell being 5 m x 5 m. Maps were randomly generated for each property and source area. In doing so, we did not consider the possibility of cross correlation among properties. Spatial autocorrelation was assumed to be weak. The reason for generating the maps was to create a "virtual" situation where all the element concentration values at each point are known. Simultaneously, we arbitrarily determined the percentage of sediment coming from sub-catchments. These values were 30 %, 10 % and 60 %, for sub-catchments 1, 2 and 3, respectively. Using these values, we determined the element concentrations in the sediment. The exercise consisted of creating different sampling strategies in a virtual environment to determine an average value for each of the different maps of element concentration and sub-catchment, under different sampling densities: 200 different average values for the "high" sampling density (average of 50 samples); 400 different average values for the "medium" sampling density (average of 25 samples); and 1,000 different average values for the "low" sampling density (average of 10 samples). All these combinations of possible values of element concentrations in the source areas were solved for the concentration in the sediment already determined for the "true" solution using limSolve (Soetaert et al., 2014) in R language. The sediment source solutions found for the different situations and values were analyzed in order to: 1) evaluate the uncertainty in the sediment source attribution; and 2) explore strategies to detect the most probable solutions that might lead to improved methods for constructing the most robust mixing models. Preliminary results on these will be presented and discussed in this communication. Key words: sediment, fingerprinting, uncertainty, variability, mixing model. References Collins, A.L., Zhang, Y., McChesney, D., Walling, D.E., Haley, S.M., Smith, P. 2012. Sediment source tracing in a lowland agricultural catchment in southern England using a modified procedure combining statistical analysis and numerical modelling. Science of the Total Environment 414: 301-317. Freeze, R.A. 1980. A stochastic-conceptual analysis of rainfall-runoff processes on a hillslope. Water Resources Research 16: 391-408.

DETERMINATION OF AMMONIA MASS EMISSION FLUX FROM HOG WASTE EFFLUENT SPRAYING OPERATION USING OPEN PATH TUNABLE DIODE LASER SPECTROSCOPY WITH VERTICAL RADIAL PLUME MAPPING ANALYSIS

EPA Science Inventory

Emission of ammonia from concentrated animal feeding operations represents an increasingly important environmental issue. Determination of total ammonia mass emission flux from extended area sources such as waste lagoons and waste effluent spraying operations can be evaluated usi...

Comparison of AERMOD and WindTrax dispersion models in determining PM10 emission rates from beef cattle feedlots

USDA-ARS?s Scientific Manuscript database

Reverse dispersion modeling has been used to determine air emission fluxes from ground-level area sources, including open-lot beef cattle feedlots. This research compared AERMOD, a Gaussian-based and currently the U.S. Environmental Protection Agency (EPA) preferred regulatory dispersion model, and ...

77 FR 20575 - Approval and Promulgation of Air Quality Implementation Plans; Wisconsin; Forest County...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-05

... redesignated area must determine by an analysis whether their emissions will have an adverse impact on those... of the MOA allows for restricting the requirements normally associated with Class I areas as these... demonstration that the emissions from the proposed new major source or major modification would have an adverse...

Complete Sets of Radiating and Nonradiating Parts of a Source and Their Fields with Applications in Inverse Scattering Limited-Angle Problems

PubMed Central

Louis, A. K.

2006-01-01

Many algorithms applied in inverse scattering problems use source-field systems instead of the direct computation of the unknown scatterer. It is well known that the resulting source problem does not have a unique solution, since certain parts of the source totally vanish outside of the reconstruction area. This paper provides for the two-dimensional case special sets of functions, which include all radiating and all nonradiating parts of the source. These sets are used to solve an acoustic inverse problem in two steps. The problem under discussion consists of determining an inhomogeneous obstacle supported in a part of a disc, from data, known for a subset of a two-dimensional circle. In a first step, the radiating parts are computed by solving a linear problem. The second step is nonlinear and consists of determining the nonradiating parts. PMID:23165060

Simulation of agricultural non-point source pollution in Xichuan by using SWAT model

NASA Astrophysics Data System (ADS)

Xing, Linan; Zuo, Jiane; Liu, Fenglin; Zhang, Xiaohui; Cao, Qiguang

2018-02-01

This paper evaluated the applicability of using SWAT to access agricultural non-point source pollution in Xichuan area. In order to build the model, DEM, soil sort and land use map, climate monitoring data were collected as basic database. The SWAT model was calibrated and validated for the SWAT was carried out using streamflow, suspended solids, total phosphorus and total nitrogen records from 2009 to 2011. Errors, coefficient of determination and Nash-Sutcliffe coefficient were considered to evaluate the applicability. The coefficient of determination were 0.96, 0.66, 0.55 and 0.66 for streamflow, SS, TN, and TP, respectively. Nash-Sutcliffe coefficient were 0.93, 0.5, 0.52 and 0.63, respectively. The results all meet the requirements. It suggested that the SWAT model can simulate the study area.

Analysis of heavy metals in the re-suspended road dusts from different functional areas in Xi'an, China.

PubMed

Wang, Qian; Lu, Xinwei; Pan, Huiyun

2016-10-01

A study on heavy metal pollution was undertaken in the re-suspended road dusts from different functional areas in Xi'an City of China to investigate the impacts of human activities and land uses on urban environment. The concentrations of Co, Cr, Cu, Mn, Ni, Pb, V, and Zn were determined using X-ray fluorescence spectrometry, and their accumulations were analyzed using enrichment factor. Correlation analysis, principal component analysis, and cluster analysis, combined with the concentration property and enrichment factor, were used to identify the possible sources of heavy metals investigated. The investigated re-suspended road dusts had Co, Cr, Cu, Pb, and Zn concentrations higher than background levels. Samples from different functional areas had diverse heavy metal concentration levels. Co, Cr, Cu, Pb, and Zn presented moderate/significant enrichment in the samples. The source analyses indicated that Mn, Ni, V, Pb, and Zn had the mixed sources of nature and traffic, Cr and Cu mainly originated from traffic source, while Co was primarily derived from construction source. Traffic and construction activities had a significant impact on urban environment. This preliminary research provides a valuable basis for urban environment protection and management.

The effects of sorting by aeolian processes on the geochemical characteristics of surface materials: a wind tunnel experiment

NASA Astrophysics Data System (ADS)

Wang, Xunming; Lang, Lili; Hua, Ting; Zhang, Caixia; Li, Hui

2018-03-01

The geochemical characteristics of aeolian and surface materials in potential source areas of dust are frequently employed in environmental reconstructions as proxies of past climate and as source tracers of aeolian sediments deposited in downwind areas. However, variations in the geochemical characteristics of these aeolian deposits that result from near-surface winds are currently poorly understood. In this study, we collected surface samples from the Ala Shan Plateau (a major potential dust source area in Central Asia) to determine the influence of aeolian processes on the geochemical characteristics of aeolian transported materials. Correlation analyses show that compared with surface materials, the elements in transported materials (e.g., Cu, As, Pb, Mn, Zn, Al, Ca, Fe, Ga, K, Mg, P, Rb, Co, Cr, Na, Nb, Si, and Zr) were subjected to significant sorting by aeolian processes, and the sorting also varied among different particle size fractions and elements. Variations in wind velocity were significantly correlated with the contents of Cr, Ga, Sr, Ca, Y, Nd, Zr, Nb, Ba, and Al, and with the Zr/Al, Zr/Rb, K/Ca, Sr/Ca, Rb/Sr, and Ca/Al ratios. Given the great variation in the geochemical characteristics of materials transported under different aeolian processes relative to those of the source materials, these results indicate that considerable uncertainty may be introduced to analyses by using surface materials to trace the potential source areas of aeolian deposits that accumulate in downwind areas.

Source of Organic Matter in 2011 Tohoku-oki Tsunami Deposits Determined by C/N　Ratios and δ13C

NASA Astrophysics Data System (ADS)

Ito, Y.; Yoshii, T.; Hamada, T.; Sasaki, T.; Tanaka, S.; Matsuyama, M.

2015-12-01

For the future mitigation of tsunami hazard in coastal areas, assessments of ancient tsunami deposits are crucially important. In order to identify tsunami deposits, several indicators have been proposed to be useful including multiple proxies using sand units, grain size and/or microfossils such as diatoms. However, tsunamis do not always leave such visible evidence in their deposits. Therefore, to characterize the tsunami inundation area for the cases without such evidence, geochemical compositions have also been applied recently. In this study, C/N and isotopic (δ13C) analyses were used to determine sources of organic matter in 2011 Tohoku-oki tsunami deposits collected from 19 coastal areas which range about 500km from north to south. We find that these parameters can be alternatively used to distinguish marine organic matter from freshwater and land plants; we confirm that a marine signature is found in most beach samples, while a signature of freshwater or land plant is recognized in soil samples obtained from unaffected inland areas. Marine signature is found in some of tsunami sand deposits close to the coastline, while the signature of freshwater or land plant is recognized in sand deposits far from the coastline. This finding suggests that marine-affected sediment was not transported to the proximity of the limit of the inundation. Marine signature is typically found in paddy field and marshy areas but not in forest or grassland, which would have supplied a large amount of land plant that affects the source of the organic matter in a tsunami deposit.

Aeromagnetic measurements in the Cascade Range and Modoc Plateau of northern California; report on work done from December 1, 1980, to May 31, 1981

USGS Publications Warehouse

Couch, Richard W.; Gemperle, Michael

1982-01-01

Spectral analysis of aeromagnetic data collected over 6orth-central California during the summer of 1980 aided in determining magnetic-source bottom depths beneath the survey area. Five regions of shallow magnetic source bottom depths were detected: 1) Secret Spring Mountain and National Lava Beds Monument area, 2) the Mount Shasta area, 3) the Eddys Mountain area, 4) the Big Valley Mountains area, and 5) an area northeast of Lassen Peak. Except for the Eddys Mountain area, all regions exhibiting shallow depths are suggested to be due to elevated Curie-point isotherms. The elevated Curie-point depth beneath Secret Spring Mountain and the National Lava Beds Monument area was found to be 4-7 km BSL (Below Sea Level) and is an extension of a zone mapped beneath an area immediately to the north in Oregon. A similar depth was detected for the Mount Shasta area and the area northeast of Lassen Peak. A depth of 4-6 km BSL was detected beneath the Big Valley Mountains area. The shallow Curie-point depths beneath Secret Spring Mountain, Mount Shasta, Big Valley Mountains, and the area northeast of Lassen Peak appear to form a segmented Zone of elevated Curie-point isotherm depths which underlies the High Cascade Mountains and Modoc Plateau in north-central California. A small area of shallow depths to magnetic-source bottoms, 4-5 km BSL, beneath the Eddys Mountain area is attributed to a lithologic boundary rather than an elevated Curie-point isotherm. Deeper magnetic source bottom depths were mapped throughout the remainder of the study area, with depths greater than 9 km BSL indicated beneath Lassen Peak and greater than ii km BSL indicated beneath the Western Cascades, Eastern Klamath Mountains, and Great Valley.

Sources of metal loads to the Alamosa River and estimation of seasonal and annual metal loads for the Alamosa River basin, Colorado, 1995-97

USGS Publications Warehouse

Ortiz, Roderick F.; Edelmann, Patrick; Ferguson, Sheryl; Stogner, Robert

2002-01-01

Metal contamination in the upper Alamosa River Basin has occurred for decades from the Summitville Mine site, from other smaller mines, and from natural, metal-enriched acidic drainage in the basin. In 1995, the need to quantify contamination from various source areas in the basin and to quantify the spatial, seasonal, and annual metal loads in the basin was identified. Data collection occurred from 1995 through 1997 at numerous sites to address data gaps. Metal loads were calculated and the percentages of metal load contributions from tributaries to three risk exposure areas were determined. Additionally, a modified time-interval method was used to estimate seasonal and annual metal loads in the Alamosa River and Wightman Fork. Sources of dissolved and total-recoverable aluminum, copper, iron, and zinc loads were determined for Exposure Areas 3a, 3b, and 3c. Alum Creek is the predominant contributor of aluminum, copper, iron, and zinc loads to Exposure Area 3a. In general, Wightman Fork was the predominant source of metals to Exposure Area 3b, particularly during the snowmelt and summer-flow periods. During the base-flow period, however, aluminum and iron loads from Exposure Area 3a were the dominant source of these metals to Exposure Area 3b. Jasper and Burnt Creeks generally contributed less than 10 percent of the metal loads to Exposure Area 3b. On a few occasions, however, Jasper and Burnt Creeks contributed a substantial percentage of the loads to the Alamosa River. The metal loads calculated for Exposure Area 3c result from upstream sources; the primary upstream sources are Wightman Fork, Alum Creek, and Iron Creek. Tributaries in Exposure Area 3c did not contribute substantially to the metal load in the Alamosa River. In many instances, the percentage of dissolved and/or total-recoverable metal load contribution from a tributary or the combined percentage of metal load contribution was greater than 100 percent of the metal load at the nearest downstream site on the Alamosa River. These data indicate that metal partitioning and metal deposition from the water column to the streambed may be occurring in Exposure Areas 3a, 3b, and 3c. Metals that are deposited to the streambed probably are resuspended and transported downstream during high streamflow periods such as during snowmelt runoff and rainfall runoff. Seasonal and annual dissolved and totalrecoverable aluminum, copper, iron, and zinc loads> for 1995?97 were estimated for Exposure Areas 1, 2, 3a, 3b, and 3c. During 1995?97, many tons of metals were transported annually through each exposure area. Generally, the largest estimated annual totalrecoverable metal mass for most metals was in 1995. The smallest estimated annual total-recoverable metal mass was in 1996, which also had the smallest annual streamflow. In 1995 and 1997, more than 60 percent of the annual total-recoverable metal loads generally was transported through each exposure area during the snowmelt period. A comparison of the estimated storm load at each site to the corresponding annual load indicated that storms contribute less than 2 percent of the annual load at any site and about 5 to 20 percent of the load during the summer-flow period.

Applicability of source scaling relations for crustal earthquakes to estimation of the ground motions of the 2016 Kumamoto earthquake

NASA Astrophysics Data System (ADS)

Irikura, Kojiro; Miyakoshi, Ken; Kamae, Katsuhiro; Yoshida, Kunikazu; Somei, Kazuhiro; Kurahashi, Susumu; Miyake, Hiroe

2017-01-01

A two-stage scaling relationship of the source parameters for crustal earthquakes in Japan has previously been constructed, in which source parameters obtained from the results of waveform inversion of strong motion data are combined with parameters estimated based on geological and geomorphological surveys. A three-stage scaling relationship was subsequently developed to extend scaling to crustal earthquakes with magnitudes greater than M w 7.4. The effectiveness of these scaling relationships was then examined based on the results of waveform inversion of 18 recent crustal earthquakes ( M w 5.4-6.9) that occurred in Japan since the 1995 Hyogo-ken Nanbu earthquake. The 2016 Kumamoto earthquake, with M w 7.0, was one of the largest earthquakes to occur since dense and accurate strong motion observation networks, such as K-NET and KiK-net, were deployed after the 1995 Hyogo-ken Nanbu earthquake. We examined the applicability of the scaling relationships of the source parameters of crustal earthquakes in Japan to the 2016 Kumamoto earthquake. The rupture area and asperity area were determined based on slip distributions obtained from waveform inversion of the 2016 Kumamoto earthquake observations. We found that the relationship between the rupture area and the seismic moment for the 2016 Kumamoto earthquake follows the second-stage scaling within one standard deviation ( σ = 0.14). The ratio of the asperity area to the rupture area for the 2016 Kumamoto earthquake is nearly the same as ratios previously obtained for crustal earthquakes. Furthermore, we simulated the ground motions of this earthquake using a characterized source model consisting of strong motion generation areas (SMGAs) based on the empirical Green's function (EGF) method. The locations and areas of the SMGAs were determined through comparison between the synthetic ground motions and observed motions. The sizes of the SMGAs were nearly coincident with the asperities with large slip. The synthetic ground motions obtained using the EGF method agree well with the observed motions in terms of acceleration, velocity, and displacement within the frequency range of 0.3-10 Hz. These findings indicate that the 2016 Kumamoto earthquake is a standard event that follows the scaling relationship of crustal earthquakes in Japan.

Seismic interferometry of the Bighorn Mountains: Using virtual source gathers to increase fold in sparse-source, dense-receiver data

NASA Astrophysics Data System (ADS)

Plescia, S. M.; Sheehan, A. F.; Haines, S. S.; Cook, S. W.; Worthington, L. L.

2016-12-01

The Bighorn Arch Seismic Experiment (BASE) was a combined active- and passive-source seismic experiment designed to image deep structures including the Moho beneath a basement-involved foreland arch. In summer 2010, over 1800 Texan receivers, with 4.5 Hz vertical component geophones, were deployed at 100-m to 1-km spacing in a region spanning the Bighorn Arch and the adjacent Bighorn and Powder River Basins. Twenty explosive sources were used to create seismic energy during a two-week acquisition period. Teleseismic earthquakes and mine blasts were also recorded during this time period. We utilize both virtual source interferometry and traditional reflection processing to better understand the deep crustal features of the region and the Moho. The large number of receivers, compared to the limited, widely spaced (10 - 30 km) active-source shots, makes the data an ideal candidate for virtual source seismic interferometry to increase fold. Virtual source interferometry results in data representing a geometry where receiver locations act as if they were seismic source positions. A virtual source gather, the product of virtual source interferometry, is produced by the cross correlation of one receiver's recording, the reference trace, with the recordings of all other receivers in a given shot gather. The cross correlation is repeated for all shot gathers and the resulting traces are stacked. This process is repeated until a virtual source gather has been determined for every real receiver location. Virtual source gathers can be processed with a standard reflection seismic processing flow to yield a reflection section. Improper static corrections can be detrimental to effective stacking, and determination of proper statics is often difficult in areas of significant contrast such as between basin and mountain areas. As such, a natural synergy exists between virtual source interferometry and modern industry reflection seismic processing, with its emphasis on detailed static correction and dense acquisition geometries.

Exploring variations of earthquake moment on patches with heterogeneous strength

NASA Astrophysics Data System (ADS)

Lin, Y. Y.; Lapusta, N.

2016-12-01

Finite-fault inversions show that earthquake slip is typically non-uniform over the ruptured region, likely due to heterogeneity of the earthquake source. Observations also show that events from the same fault area can have the same source duration but different magnitude ranging from 0.0 to 2.0 (Lin et al., GJI, 2016). Strong heterogeneity in strength over a patch could provide a potential explanation of such behavior, with the event duration controlled by the size of the patch and event magnitude determined by how much of the patch area has been ruptured. To explore this possibility, we numerically simulate earthquake sequences on a rate-and-state fault, with a seismogenic patch governed by steady-state velocity-weakening friction surrounded by a steady-state velocity-strengthening region. The seismogenic patch contains strong variations in strength due to variable normal stress. Our long-term simulations of slip in this model indeed generate sequences of earthquakes of various magnitudes. In some seismic events, dynamic rupture cannot overcome areas with higher normal strength, and smaller events result. When the higher-strength areas are loaded by previous slip and rupture, larger events result, as expected. Our current work is directed towards exploring a range of such models, determining the variability in the seismic moment that they can produce, and determining the observable properties of the resulting events.

Source apportionment of PAHs and n-alkanes bound to PM1 collected near the Venice highway.

PubMed

Valotto, Gabrio; Rampazzo, Giancarlo; Gonella, Francesco; Formenton, Gianni; Ficotto, Silvia; Giraldo, Giorgia

2017-04-01

n-Alkanes and polycyclic aromatic hydrocarbons (PAHs) bound to atmospheric particulate matter (PM 1 ) were investigated in a traffic site located in an urban area of Venice Province (Eastern Po Valley, Italy) during the cold season. Considering the critical situation affecting the Veneto Region concerning the atmospheric pollution and the general lack of information on PM 1 composition and emission in this area, this experimental study aims at determining the source profile, their relative contributions and the dispersion of finer particles. Four sources were identified and quantified using the Positive Matrix Factorization receptor model: (1) mixed combustions related to the residential activities, (2) agricultural biomass burning in addition to the resuspension of anthropogenic and natural debris carried by the wind, (3) gasoline and (4) diesel traffic-related combustions. The role of local atmospheric circulation was also investigated to identify the pollutant sources. Copyright © 2016. Published by Elsevier B.V.

Fast determination of ⁹⁰Sr/⁹⁰Y activity in milk by Cherenkov counting.

PubMed

Tsroya, S; Dolgin, B; German, U; Pelled, O; Alfassi, Z B

2013-12-01

Cherenkov counting of the ⁹⁰Sr/⁹⁰Y pure beta emitters is an attractive method for ⁹⁰Sr activity determination, but the color quenching effect may be significant, especially for strongly colored or semi-opaque media. A quench correction method based on the external source of some liquid scintillation systems (named ESAR - external source area ratio) was proposed and checked for aqueous solutions and was proved to be effective also for urine samples. In the present work, the application of the ESAR method for fast determination of ⁹⁰Sr/⁹⁰Y activity in milk samples is described. © 2013 Elsevier Ltd. All rights reserved.

Network analysis of corticocortical connections reveals ventral and dorsal processing streams in mouse visual cortex

PubMed Central

Wang, Quanxin; Sporns, Olaf; Burkhalter, Andreas

2012-01-01

Much of the information used for visual perception and visually guided actions is processed in complex networks of connections within the cortex. To understand how this works in the normal brain and to determine the impact of disease, mice are promising models. In primate visual cortex, information is processed in a dorsal stream specialized for visuospatial processing and guided action and a ventral stream for object recognition. Here, we traced the outputs of 10 visual areas and used quantitative graph analytic tools of modern network science to determine, from the projection strengths in 39 cortical targets, the community structure of the network. We found a high density of the cortical graph that exceeded that previously shown in monkey. Each source area showed a unique distribution of projection weights across its targets (i.e. connectivity profile) that was well-fit by a lognormal function. Importantly, the community structure was strongly dependent on the location of the source area: outputs from medial/anterior extrastriate areas were more strongly linked to parietal, motor and limbic cortex, whereas lateral extrastriate areas were preferentially connected to temporal and parahippocampal cortex. These two subnetworks resemble dorsal and ventral cortical streams in primates, demonstrating that the basic layout of cortical networks is conserved across species. PMID:22457489

Available Transfer Capability Determination Using Hybrid Evolutionary Algorithm

NASA Astrophysics Data System (ADS)

Jirapong, Peeraool; Ongsakul, Weerakorn

2008-10-01

This paper proposes a new hybrid evolutionary algorithm (HEA) based on evolutionary programming (EP), tabu search (TS), and simulated annealing (SA) to determine the available transfer capability (ATC) of power transactions between different control areas in deregulated power systems. The optimal power flow (OPF)-based ATC determination is used to evaluate the feasible maximum ATC value within real and reactive power generation limits, line thermal limits, voltage limits, and voltage and angle stability limits. The HEA approach simultaneously searches for real power generations except slack bus in a source area, real power loads in a sink area, and generation bus voltages to solve the OPF-based ATC problem. Test results on the modified IEEE 24-bus reliability test system (RTS) indicate that ATC determination by the HEA could enhance ATC far more than those from EP, TS, hybrid TS/SA, and improved EP (IEP) algorithms, leading to an efficient utilization of the existing transmission system.

Identifying natural and anthropogenic sources of metals in urban and rural soils using GIS-based data, PCA, and spatial interpolation

PubMed Central

Davis, Harley T.; Aelion, C. Marjorie; McDermott, Suzanne; Lawson, Andrew B.

2009-01-01

Determining sources of neurotoxic metals in rural and urban soils is important for mitigating human exposure. Surface soil from four areas with significant clusters of mental retardation and developmental delay (MR/DD) in children, and one control site were analyzed for nine metals and characterized by soil type, climate, ecological region, land use and industrial facilities using readily-available GIS-based data. Kriging, principal component analysis (PCA) and cluster analysis (CA) were used to identify commonalities of metal distribution. Three MR/DD areas (one rural and two urban) had similar soil types and significantly higher soil metal concentrations. PCA and CA results suggested that Ba, Be and Mn were consistently from natural sources; Pb and Hg from anthropogenic sources; and As, Cr, Cu, and Ni from both sources. Arsenic had low commonality estimates, was highly associated with a third PCA factor, and had a complex distribution, complicating mitigation strategies to minimize concentrations and exposures. PMID:19361902

Wind-tunnel Modelling of Dispersion from a Scalar Area Source in Urban-Like Roughness

NASA Astrophysics Data System (ADS)

Pascheke, Frauke; Barlow, Janet F.; Robins, Alan

2008-01-01

A wind-tunnel study was conducted to investigate ventilation of scalars from urban-like geometries at neighbourhood scale by exploring two different geometries a uniform height roughness and a non-uniform height roughness, both with an equal plan and frontal density of λ p = λ f = 25%. In both configurations a sub-unit of the idealized urban surface was coated with a thin layer of naphthalene to represent area sources. The naphthalene sublimation method was used to measure directly total area-averaged transport of scalars out of the complex geometries. At the same time, naphthalene vapour concentrations controlled by the turbulent fluxes were detected using a fast Flame Ionisation Detection (FID) technique. This paper describes the novel use of a naphthalene coated surface as an area source in dispersion studies. Particular emphasis was also given to testing whether the concentration measurements were independent of Reynolds number. For low wind speeds, transfer from the naphthalene surface is determined by a combination of forced and natural convection. Compared with a propane point source release, a 25% higher free stream velocity was needed for the naphthalene area source to yield Reynolds-number-independent concentration fields. Ventilation transfer coefficients w T / U derived from the naphthalene sublimation method showed that, whilst there was enhanced vertical momentum exchange due to obstacle height variability, advection was reduced and dispersion from the source area was not enhanced. Thus, the height variability of a canopy is an important parameter when generalising urban dispersion. Fine resolution concentration measurements in the canopy showed the effect of height variability on dispersion at street scale. Rapid vertical transport in the wake of individual high-rise obstacles was found to generate elevated point-like sources. A Gaussian plume model was used to analyse differences in the downstream plumes. Intensified lateral and vertical plume spread and plume dilution with height was found for the non-uniform height roughness.

A Greedy Scanning Data Collection Strategy for Large-Scale Wireless Sensor Networks with a Mobile Sink.

PubMed

Zhu, Chuan; Zhang, Sai; Han, Guangjie; Jiang, Jinfang; Rodrigues, Joel J P C

2016-09-06

Mobile sink is widely used for data collection in wireless sensor networks. It can avoid 'hot spot' problems but energy consumption caused by multihop transmission is still inefficient in real-time application scenarios. In this paper, a greedy scanning data collection strategy (GSDCS) is proposed, and we focus on how to reduce routing energy consumption by shortening total length of routing paths. We propose that the mobile sink adjusts its trajectory dynamically according to the changes of network, instead of predetermined trajectory or random walk. Next, the mobile sink determines which area has more source nodes, then it moves toward this area. The benefit of GSDCS is that most source nodes are no longer needed to upload sensory data for long distances. Especially in event-driven application scenarios, when event area changes, the mobile sink could arrive at the new event area where most source nodes are located currently. Hence energy can be saved. Analytical and simulation results show that compared with existing work, our GSDCS has a better performance in specific application scenarios.

A Greedy Scanning Data Collection Strategy for Large-Scale Wireless Sensor Networks with a Mobile Sink

PubMed Central

Zhu, Chuan; Zhang, Sai; Han, Guangjie; Jiang, Jinfang; Rodrigues, Joel J. P. C.

2016-01-01

Mobile sink is widely used for data collection in wireless sensor networks. It can avoid ‘hot spot’ problems but energy consumption caused by multihop transmission is still inefficient in real-time application scenarios. In this paper, a greedy scanning data collection strategy (GSDCS) is proposed, and we focus on how to reduce routing energy consumption by shortening total length of routing paths. We propose that the mobile sink adjusts its trajectory dynamically according to the changes of network, instead of predetermined trajectory or random walk. Next, the mobile sink determines which area has more source nodes, then it moves toward this area. The benefit of GSDCS is that most source nodes are no longer needed to upload sensory data for long distances. Especially in event-driven application scenarios, when event area changes, the mobile sink could arrive at the new event area where most source nodes are located currently. Hence energy can be saved. Analytical and simulation results show that compared with existing work, our GSDCS has a better performance in specific application scenarios. PMID:27608022

Statiscal analysis of an earthquake-induced landslide distribution - The 1989 Loma Prieta, California event

USGS Publications Warehouse

Keefer, D.K.

2000-01-01

The 1989 Loma Prieta, California earthquake (moment magnitude, M=6.9) generated landslides throughout an area of about 15,000 km2 in central California. Most of these landslides occurred in an area of about 2000 km2 in the mountainous terrain around the epicenter, where they were mapped during field investigations immediately following the earthquake. The distribution of these landslides is investigated statistically, using regression and one-way analysisof variance (ANOVA) techniques to determine how the occurrence of landslides correlates with distance from the earthquake source, slope steepness, and rock type. The landslide concentration (defined as the number of landslide sources per unit area) has a strong inverse correlation with distance from the earthquake source and a strong positive correlation with slope steepness. The landslide concentration differs substantially among the various geologic units in the area. The differences correlate to some degree with differences in lithology and degree of induration, but this correlation is less clear, suggesting a more complex relationship between landslide occurrence and rock properties. ?? 2000 Elsevier Science B.V. All rights reserved.

Speed of CMEs and the Magnetic Non-Potentiality of their Source Active Regions

NASA Technical Reports Server (NTRS)

Tiwari, Sanjiv Kumar; Falconer, David Allen; Moore, Ronald L.; Venkatakrishnan, P.; Winebarger, Amy R.; Khazanov, Igor G.

2014-01-01

Most fast coronal mass ejections (CMEs) originate from solar active regions (ARs). Non-potentiality of ARs plausibly determines the speed of CMEs in the outer corona. Several other unexplored parameters might be important as well. To find out the relation between the intial speed of CMEs and the non-potentiality of source ARs, we identified over a hundred of CMEs with source ARs via their co-produced flares. The speed of the CMEs are collected from the SOHO LASCO CME catalog. We have used vector magnetograms obtained with HMI/SDO, to evaluate various magnetic non-potentiality parameters, e.g. magnetic free-energy proxies, twist, shear angle, signed shear angle, net current etc. We have also included several other parameters e.g. total unsigned flux, magnetic area of ARs, area of sunspots, to investigate their correlation, if any, with the initial speeds of CMEs. Our preliminary results show that the ARs with larger non-potentiality and area produce faster CMEs but they can also produce slow ones. The ARs with lesser non-potentiality and area generally produce only slower CMEs.

Characteristics of organic compounds in PM2.5 at urban and remote areas in Korea

NASA Astrophysics Data System (ADS)

Choi, A.; Lee, J.; Shin, H. J.; Lee, M.; Jin seok, H.; Lim, J.

2016-12-01

Organic aerosols contain thousands of organic compounds and contribute to 20%-90% of the total fine aerosol mass (Kanakidou et al., 2005). These organic aerosols originate from anthropogenic and natural (biogenic and geologic) sources and alter physical and chemical properties in the atmosphere depending on the atmospheric and meteorological conditions. About one hundred individual organic compounds in PM2.5 at Seoul (urban area) and Baengnyeong Island (remote area) were identified and quantified using gas chromatography/mass spectrometry (GC/MS) in order to understand the characteristics of organic compounds in PM2.5 at these areas. Further, major factors to determine their concentrations in the atmosphere were investigated. Organic compounds analyzed in this study were classified into six groups, n-alkanes, polycyclic aromatic hydrocarbons (PAHs), hopanes, fatty acids (FA), dicarboxylic acids (DCAs), and sugars. Daily variation of organic compounds concentrations at Seoul were not high, while, the concentrations of organic compounds at Baengnyeong Island showed high daily variation. This is might due to frequent change of source strength and/or SOA formation in this region. Through correlations of organic compounds with other air pollutants and factor analysis at both sites, it found that major factors (or source) for the determination of organic compounds concentrations at Seoul and Baengnyeong Island were different. The major sources at Seoul were anthropogenic sources such as vehicular emission and coal combustions, while, SOA formation and biomass burning were more attributed more to the organic compounds concentrations at Baengnyeong Island.References Kanakidou, M., Seinfeld, J.H., Pandis, S.N., Barnes, I., Dentener, F.J., Facchini, M.C., Van Dingenen, R., Ervens, B., Nenes, A., Nielsen, C.J., Swietlicki, E., Putaud, J.P., Balkanski, Y., Fuzzi, S., Horth, J., Moortgat, G.K., Winterhalter, R., Myhre, C.E.L., Tsigaridis, K., Vignati, E., Stephanou, E.G., Wilson, J., 2005. Organic aerosol and global climate modelling: a review. Atmos. Chem. Phys. 5, 1053e1123.

Tracking the 10Be-26Al source-area signal in sediment-routing systems of arid central Australia

NASA Astrophysics Data System (ADS)

Struck, Martin; Jansen, John D.; Fujioka, Toshiyuki; Codilean, Alexandru T.; Fink, David; Fülöp, Réka-Hajnalka; Wilcken, Klaus M.; Price, David M.; Kotevski, Steven; Fifield, L. Keith; Chappell, John

2018-05-01

Sediment-routing systems continuously transfer information and mass from eroding source areas to depositional sinks. Understanding how these systems alter environmental signals is critical when it comes to inferring source-area properties from the sedimentary record. We measure cosmogenic 10Be and 26Al along three large sediment-routing systems ( ˜ 100 000 km2) in central Australia with the aim of tracking downstream variations in 10Be-26Al inventories and identifying the factors responsible for these variations. By comparing 56 new cosmogenic 10Be and 26Al measurements in stream sediments with matching data (n = 55) from source areas, we show that 10Be-26Al inventories in hillslope bedrock and soils set the benchmark for relative downstream modifications. Lithology is the primary determinant of erosion-rate variations in source areas and despite sediment mixing over hundreds of kilometres downstream, a distinct lithological signal is retained. Post-orogenic ranges yield catchment erosion rates of ˜ 6-11 m Myr-1 and silcrete-dominant areas erode as slow as ˜ 0.2 m Myr-1. 10Be-26Al inventories in stream sediments indicate that cumulative-burial terms increase downstream to mostly ˜ 400-800 kyr and up to ˜ 1.1 Myr. The magnitude of the burial signal correlates with increasing sediment cover downstream and reflects assimilation from storages with long exposure histories, such as alluvial fans, desert pavements, alluvial plains, and aeolian dunes. We propose that the tendency for large alluvial rivers to mask their 10Be-26Al source-area signal differs according to geomorphic setting. Signal preservation is favoured by (i) high sediment supply rates, (ii) high mean runoff, and (iii) a thick sedimentary basin pile. Conversely, signal masking prevails in landscapes of (i) low sediment supply and (ii) juxtaposition of sediment storages with notably different exposure histories.

Risk assessment of water pollution sources based on an integrated k-means clustering and set pair analysis method in the region of Shiyan, China.

PubMed

Li, Chunhui; Sun, Lian; Jia, Junxiang; Cai, Yanpeng; Wang, Xuan

2016-07-01

Source water areas are facing many potential water pollution risks. Risk assessment is an effective method to evaluate such risks. In this paper an integrated model based on k-means clustering analysis and set pair analysis was established aiming at evaluating the risks associated with water pollution in source water areas, in which the weights of indicators were determined through the entropy weight method. Then the proposed model was applied to assess water pollution risks in the region of Shiyan in which China's key source water area Danjiangkou Reservoir for the water source of the middle route of South-to-North Water Diversion Project is located. The results showed that eleven sources with relative high risk value were identified. At the regional scale, Shiyan City and Danjiangkou City would have a high risk value in term of the industrial discharge. Comparatively, Danjiangkou City and Yunxian County would have a high risk value in terms of agricultural pollution. Overall, the risk values of north regions close to the main stream and reservoir of the region of Shiyan were higher than that in the south. The results of risk level indicated that five sources were in lower risk level (i.e., level II), two in moderate risk level (i.e., level III), one in higher risk level (i.e., level IV) and three in highest risk level (i.e., level V). Also risks of industrial discharge are higher than that of the agricultural sector. It is thus essential to manage the pillar industry of the region of Shiyan and certain agricultural companies in the vicinity of the reservoir to reduce water pollution risks of source water areas. Copyright © 2016 Elsevier B.V. All rights reserved.

Urban air quality in a mid-size city - PM2.5 composition, sources and identification of impact areas: From local to long range contributions

NASA Astrophysics Data System (ADS)

Squizzato, Stefania; Cazzaro, Marta; Innocente, Elena; Visin, Flavia; Hopke, Philip K.; Rampazzo, Giancarlo

2017-04-01

Urban air quality represents a major public health burden and is a long-standing concern to European citizens. Combustion processes and traffic-related emissions represent the main primary particulate matter (PM) sources in urban areas. Other sources can also affect air quality (e.g., secondary aerosol, industrial) depending on the characteristics of the study area. Thus, the identification and the apportionment of all sources is of crucial importance to make effective corrective decisions within environmental policies. The aim of this study is to evaluate the impacts of different emissions sources on PM2.5 concentrations and compositions in a mid-size city in the Po Valley (Treviso, Italy). Data have been analyzed to highlight compositional differences (elements and major inorganic ions), to determine PM2.5 sources and their contributions, and to evaluate the influence of air mass movements. Non-parametric tests, positive matrix factorization (PMF), conditional bivariate probability function (CBPF), and concentration weighted trajectory (CWT) have been used in a multi-chemometrics approach to understand the areal-scale (proximate, local, long-range) where different sources act on PM2.5 levels and composition. Results identified three levels of scale from which the pollution arose: (i) a proximate local scale (close to the sampling site) for traffic non-exhaust and resuspended dust sources; (ii) a local urban scale (including both sampling site and areas close to them) for combustion and industrial; and (iii) a regional scale characterized by ammonium nitrate and ammonium sulfate. This approach and results can help to develop and adopt better air quality policy action.

Utilization of 134Cs/137Cs in the environment to identify the reactor units that caused atmospheric releases during the Fukushima Daiichi accident

NASA Astrophysics Data System (ADS)

Chino, Masamichi; Terada, Hiroaki; Nagai, Haruyasu; Katata, Genki; Mikami, Satoshi; Torii, Tatsuo; Saito, Kimiaki; Nishizawa, Yukiyasu

2016-08-01

The Fukushima Daiichi nuclear power reactor units that generated large amounts of airborne discharges during the period of March 12-21, 2011 were identified individually by analyzing the combination of measured 134Cs/137Cs depositions on ground surfaces and atmospheric transport and deposition simulations. Because the values of 134Cs/137Cs are different in reactor units owing to fuel burnup differences, the 134Cs/137Cs ratio measured in the environment was used to determine which reactor unit ultimately contaminated a specific area. Atmospheric dispersion model simulations were used for predicting specific areas contaminated by each dominant release. Finally, by comparing the results from both sources, the specific reactor units that yielded the most dominant atmospheric release quantities could be determined. The major source reactor units were Unit 1 in the afternoon of March 12, 2011, Unit 2 during the period from the late night of March 14 to the morning of March 15, 2011. These results corresponded to those assumed in our previous source term estimation studies. Furthermore, new findings suggested that the major source reactors from the evening of March 15, 2011 were Units 2 and 3 and that the dominant source reactor on March 20, 2011 temporally changed from Unit 3 to Unit 2.

Utilization of (134)Cs/(137)Cs in the environment to identify the reactor units that caused atmospheric releases during the Fukushima Daiichi accident.

PubMed

Chino, Masamichi; Terada, Hiroaki; Nagai, Haruyasu; Katata, Genki; Mikami, Satoshi; Torii, Tatsuo; Saito, Kimiaki; Nishizawa, Yukiyasu

2016-08-22

The Fukushima Daiichi nuclear power reactor units that generated large amounts of airborne discharges during the period of March 12-21, 2011 were identified individually by analyzing the combination of measured (134)Cs/(137)Cs depositions on ground surfaces and atmospheric transport and deposition simulations. Because the values of (134)Cs/(137)Cs are different in reactor units owing to fuel burnup differences, the (134)Cs/(137)Cs ratio measured in the environment was used to determine which reactor unit ultimately contaminated a specific area. Atmospheric dispersion model simulations were used for predicting specific areas contaminated by each dominant release. Finally, by comparing the results from both sources, the specific reactor units that yielded the most dominant atmospheric release quantities could be determined. The major source reactor units were Unit 1 in the afternoon of March 12, 2011, Unit 2 during the period from the late night of March 14 to the morning of March 15, 2011. These results corresponded to those assumed in our previous source term estimation studies. Furthermore, new findings suggested that the major source reactors from the evening of March 15, 2011 were Units 2 and 3 and that the dominant source reactor on March 20, 2011 temporally changed from Unit 3 to Unit 2.

Utilization of 134Cs/137Cs in the environment to identify the reactor units that caused atmospheric releases during the Fukushima Daiichi accident

PubMed Central

Chino, Masamichi; Terada, Hiroaki; Nagai, Haruyasu; Katata, Genki; Mikami, Satoshi; Torii, Tatsuo; Saito, Kimiaki; Nishizawa, Yukiyasu

2016-01-01

The Fukushima Daiichi nuclear power reactor units that generated large amounts of airborne discharges during the period of March 12–21, 2011 were identified individually by analyzing the combination of measured 134Cs/137Cs depositions on ground surfaces and atmospheric transport and deposition simulations. Because the values of 134Cs/137Cs are different in reactor units owing to fuel burnup differences, the 134Cs/137Cs ratio measured in the environment was used to determine which reactor unit ultimately contaminated a specific area. Atmospheric dispersion model simulations were used for predicting specific areas contaminated by each dominant release. Finally, by comparing the results from both sources, the specific reactor units that yielded the most dominant atmospheric release quantities could be determined. The major source reactor units were Unit 1 in the afternoon of March 12, 2011, Unit 2 during the period from the late night of March 14 to the morning of March 15, 2011. These results corresponded to those assumed in our previous source term estimation studies. Furthermore, new findings suggested that the major source reactors from the evening of March 15, 2011 were Units 2 and 3 and that the dominant source reactor on March 20, 2011 temporally changed from Unit 3 to Unit 2. PMID:27546490

RACT/BACT/LAER Clearninghouse (RBLC)

EPA Pesticide Factsheets

OAR's RACT, BACT, LAER Clearinghouse (RBLC) data asset contains summary information on selected air permitting actions from EPA, state, and local permitting agencies across the U.S., as well as a number of international permit records supplied by air pollution control agencies in Mexico and Canada. The acronyms refer to program requirements of the New Source Review (NSR) program: RACT is Reasonably Available Control Technology and applies to existing sources in areas that are not meeting national ambient air quality standards (i.e., non-attainment areas); BACT is Best Available Control Technology and applies to major new or modified sources in clean areas (i.e., attainment areas). LAER, or Lowest Achievable Emission Rate, is required on major new or modified sources in non-attainment areas. As of 2012, RBLC includes approximately 6,500 entries. With the exception of LAER permit determinations, whose inclusion in RBLC is mandatory, participation is voluntary. Coverage is therefore not complete or necessarily representative.Required under Section 108 of the 1990 Amendments to the Clean Air Act, RBLC provides users 00e2?? typically permit writers, permit applicants or holders, and the public 00e2?? with references and personal contacts to support ongoing air pollution control activities. Information is detailed enough for users to know whether a permit is applicable to their needs. Users may then contact the appropriate agency to access the permit or discuss it wit

I/O values for determination of the origin of some indoor organic pollutants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Otson, R.; Zhu, J.

To reduce human health risks resulting from exposure to toxic chemicals, it is important to determine the origin of such substances. The ratio (I/O) of indoor to outdoor concentrations of selected airborne vapor phase organic compounds (VPOC) was used to estimate the contribution of indoor sources to levels of the compounds in the air of 44 homes selected randomly in the Greater Toronto Area (GTA). Average I/O values for all of the homes were greater 1.5 for 10 of the 20 detected target compounds, and it could be concluded that indoor VPOC sources had a greater impact on indoor airmore » quality than outdoor air in these instances. A significant finding, which aptly demonstrates the importance of indoor sources and pollution, was the overall I/O value of 5.2 for the 44 representative GTA homes. Possible indoor sources for most of the 10 compounds could be identified, based on information collected by means of a questionnaire, as well as from the scientific literature. However, possible sources for some compounds could not be determined as readily, probably because of the presence of multiple sources, and sources which had not been previously noted, such as foods and beverages. The sensitivity of I/O values to various factors (e.g., source strength, air exchange rates, precision of measurements, unanticipated sources), and the reliability of determining the origin of pollutants by use of I/O values alone were examined, with some examples. If used judiciously, the I/O value can be a useful tool for IAQ investigations.« less

Determination of Destructed and Infracted Forest Areas with Multi-temporal High Resolution Satellite Images

NASA Astrophysics Data System (ADS)

Seker, D. Z.; Unal, A.; Kaya, S.; Alganci, U.

2015-12-01

Migration from rural areas to city centers and their surroundings is an important problem of not only our country but also the countries that under development stage. This uncontrolled and huge amount of migration brings out urbanization and socio - economic problems. The demand on settling the industrial areas and commercial activities nearby the city centers results with a negative change in natural land cover on cities. Negative impacts of human induced activities on natural resources and land cover has been continuously increasing for decades. The main human activities that resulted with destruction and infraction of forest areas can be defined as mining activities, agricultural activities, industrial / commercial activities and urbanization. Temporal monitoring of the changes in spatial distribution of forest areas is significantly important for effective management and planning progress. Changes can occur as spatially large destructions or small infractions. Therefore there is a need for reliable, fast and accurate data sources. At this point, satellite images proved to be a good data source for determination of the land use /cover changes with their capability of monitoring large areas with reasonable temporal resolutions. Spectral information derived from images provides discrimination of land use/cover types from each other. Developments in remote sensing technology in the last decade improved the spatial resolution of satellites and high resolution images were started to be used to detect even small changes in the land surface. As being the megacity of Turkey, Istanbul has been facing a huge migration for the last 20 years and effects of urbanization and other human based activities over forest areas are significant. Main focus of this study is to determine the destructions and infractions in forest areas of Istanbul, Turkey with 2.5m resolution SPOT 5 multi-temporal satellite imagery. Analysis was mainly constructed on threshold based classification of multi-temporal vegetation index data derived from satellite images. Determined changes were exported to GIS environment and spatial overlay and intersection analyses were performed with use of forest type maps and authorized area maps in order to demonstrate the actual situation of destructions and infractions.

Recharge sources and residence times of groundwater as determined by geochemical tracers in the Mayfield Area, southwestern Idaho, 2011–12

USGS Publications Warehouse

Hopkins, Candice B.

2013-01-01

Parties proposing residential development in the area of Mayfield, Idaho are seeking a sustainable groundwater supply. During 2011–12, the U.S. Geological Survey, in cooperation with the Idaho Department of Water Resources, used geochemical tracers in the Mayfield area to evaluate sources of aquifer recharge and differences in groundwater residence time. Fourteen groundwater wells and one surface-water site were sampled for major ion chemistry, metals, stable isotopes, and age tracers; data collected from this study were used to evaluate the sources of groundwater recharge and groundwater residence times in the area. Major ion chemistry varied along a flow path between deeper wells, suggesting an upgradient source of dilute water, and a downgradient source of more concentrated water with the geochemical signature of the Idaho Batholith. Samples from shallow wells had elevated nutrient concentrations, a more positive oxygen-18 signature, and younger carbon-14 dates than deep wells, suggesting that recharge comes from young precipitation and surface-water infiltration. Samples from deep wells generally had higher concentrations of metals typical of geothermal waters, a more negative oxygen-18 signature, and older carbon-14 values than samples from shallow wells, suggesting that recharge comes from both infiltration of meteoric water and another source. The chemistry of groundwater sampled from deep wells is somewhat similar to the chemistry in geothermal waters, suggesting that geothermal water may be a source of recharge to this aquifer. Results of NETPATH mixing models suggest that geothermal water composes 1–23 percent of water in deep wells. Chlorofluorocarbons were detected in every sample, which indicates that all groundwater samples contain at least a component of young recharge, and that groundwater is derived from multiple recharge sources. Conclusions from this study can be used to further refine conceptual hydrological models of the area.

Heavy Metal Contamination Assessment and Partition for Industrial and Mining Gathering Areas

PubMed Central

Guan, Yang; Shao, Chaofeng; Ju, Meiting

2014-01-01

Industrial and mining activities have been recognized as the major sources of soil heavy metal contamination. This study introduced an improved Nemerow index method based on the Nemerow and geo-accumulation index. Taking a typical industrial and mining gathering area in Tianjin (China) as example, this study then analyzed the contamination sources as well as the ecological and integrated risks. The spatial distribution of the contamination level and ecological risk were determined using Geographic Information Systems. The results are as follows: (1) Zinc showed the highest contaminant level in the study area; the contamination levels of the other seven heavy metals assessed were relatively lower. (2) The combustion of fossil fuels and emissions from industrial and mining activities were the main sources of contamination in the study area. (3) The overall contamination level of heavy metals in the study area ranged from heavily contaminated to extremely contaminated and showed an uneven distribution. (4) The potential ecological risk showed an uneven distribution, and the overall ecological risk level ranged from low to moderate. This study also emphasized the importance of partition in industrial and mining areas, the extensive application of spatial analysis methods, and the consideration of human health risks in future studies. PMID:25032743

[Evaluation of environmental conditions: air, water and soil in areas of mining activity in Boyacá, Colombia].

PubMed

Agudelo-Calderón, Carlos A; Quiroz-Arcentales, Leonardo; García-Ubaque, Juan C; Robledo-Martínez, Rocío; García-Ubaque, Cesar A

2016-02-01

Objectives To determine concentrations of PM10, mercury and lead in indoor air of homes, water sources and soil in municipalities near mining operations. Method 6 points were evaluated in areas of influence and 2 in control areas. For measurements of indoor air, we used the NIOSH 600 method (PM10), NIOSH 6009 (mercury) and NIOSH 7300 (lead). For water analysis we used the IDEAM Guide for monitoring discharges. For soil analysis, we used the cold vapor technique (mercury) and atomic absorption (lead). Results In almost all selected households, the average PM10 and mercury concentrations in indoor air exceeded applicable air quality standards. Concentrations of lead were below standard levels. In all water sources, high concentrations of lead were found and in some places within the mining areas, high levels of iron, aluminum and mercury were also found. In soil, mercury concentrations were below the detection level and for lead, differences between the monitored points were observed. Conclusions The results do not establish causal relationships between mining and concentration of these pollutants in the evaluated areas because of the multiplicity of sources in the area. However, such studies provide important information, useful to agents of the environmental health system and researchers. Installation of networks for environmental monitoring to obtain continuous reports is suggested.

Media and interpersonal persuasions in the polio eradication campaign in northern Nigeria.

PubMed

Ozohu-Suleiman, Yakubu

2010-09-01

This study is premised on the increasing global concerns over the widespread resistance to polio eradication campaign in northern Nigeria. It aims to determine the level of campaign acceptance and compare the influences of mass media and interpersonal communication sources in Zaria local government area, being one of the high-risk (WPV-endemic) areas in northern Nigeria, where campaign resistance is known to be high. By way of quantitative survey, the study utilized 10% sample of the populations of eight out of the thirteen Wards in Zaria local government area, with a response rate of 78.6%. Findings reveal close ranks between campaign acceptance and resistance in the local government area, thus further confirming the difficulties still faced in polio eradication campaign in the region. This study also indicates higher performance of Interpersonal than Mass Media sources in influencing campaign acceptance and resistance in the local communities. Contact with friends and relations was rated the most influential interpersonal sources in the acceptance and resistance decision of individuals, while newspapers and magazines were rated most influential media sources that influenced campaign resistance in the local communities. The study concludes that a polio eradication campaign, backed with competent and sufficient communication expertise that utilizes knowledge-based indigenous interpersonal communication strategies will likely result in greater community acceptance in northern Nigeria.

Model assessment of atmospheric pollution control schemes for critical emission regions

NASA Astrophysics Data System (ADS)

Zhai, Shixian; An, Xingqin; Liu, Zhao; Sun, Zhaobin; Hou, Qing

2016-01-01

In recent years, the atmospheric environment in portions of China has become significantly degraded and the need for emission controls has become urgent. Because more international events are being planned, it is important to implement air quality assurance targeted at significant events held over specific periods of time. This study sets Yanqihu (YQH), Beijing, the location of the 2014 Beijing APEC (Asia-Pacific Economic Cooperation) summit, as the target region. By using the atmospheric inversion model FLEXPART, we determined the sensitive source zones that had the greatest impact on the air quality of the YQH region in November 2012. We then used the air-quality model Models-3/CMAQ and a high-resolution emissions inventory of the Beijing-Tianjian-Hebei region to establish emission reduction tests for the entire source area and for specific sensitive source zones. This was achieved by initiating emission reduction schemes at different ratios and different times. The results showed that initiating a moderate reduction of emissions days prior to a potential event is more beneficial to the air quality of Beijing than initiating a high-strength reduction campaign on the day of the event. The sensitive source zone of Beijing (BJ-Sens) accounts for 54.2% of the total source area of Beijing (BJ), but its reduction effect reaches 89%-100% of the total area, with a reduction efficiency 1.6-1.9 times greater than that of the entire area. The sensitive source zone of Huabei (HuaB-Sens.) only represents 17.6% of the total area of Huabei (HuaB), but its emission reduction effect reaches 59%-97% of the entire area, with a reduction efficiency 4.2-5.5 times greater than that of the total area. The earlier that emission reduction measures are implemented, the greater the effect they have on preventing the transmission of pollutants. In addition, expanding the controlling areas to sensitive provinces and cities around Beijing (HuaB-sens) can significantly accelerate the reduction effects compared to controlling measures only in the Beijing sensitive source zone (BJ-Sens). Therefore, when enacting emission reduction schemes, cooperating with surrounding provinces and cities, as well as narrowing the reduction scope to specific sensitive source zones prior to unfavorable meteorological conditions, can help reduce emissions control costs and improve the efficiency and maneuverability of emission reduction schemes.

Determining sources of water and contaminants to wells in a carbonate aquifer near Martinsburg, Blair County, Pennsylvania, by use of geochemical indicators, analysis of anthropogenic contaminants, and simulation of ground-water flow

USGS Publications Warehouse

Lindsey, Bruce D.; Koch, Michele L.

2004-01-01

Water supply for the Borough of Martinsburg, Pa., is from two well fields (Wineland and Hershberger) completed in carbonate-bedrock aquifers in the Morrison Cove Valley. Water supply is plentiful; however, waters with high concentrations of nitrate are a concern. This report describes the sources of water and contaminants to the supply wells. A review of previous investigations was used to establish the aquifer framework and estimate aquifer hydraulic properties. Aquifer framework and simulation of ground-water flow in a 25-square-mile area using the MODFLOW model helped to further constrain aquifer hydraulic properties and identify water-source areas in the zone of contribution of ground water to the well fields. Flow simulation identified potential contaminant-source areas. Data on contaminants and geochemical characteristics of ground water at the well fields were compared to the results of flow simulation. The Woodbury Anticline controls the aquifer framework near the well fields and four carbonate-bedrock formations contain the primary aquifers. Three carbonate-bedrock aquifers of Ordovician age overlie the Gatesburg aquifer of Cambrian age on the flanks of the anticline. Fracture, not conduit, permeability was determined to be the dominant water-bearing characteristic of the bedrock. The horizontal hydraulic conductivity of the Gatesburg aquifer is about 36 feet per day. The other carbonate aquifers (Nittany/Stonehenge, Bellefonte/Axemann, and Coburn through Loysburg aquifers) overlying and flanking the Gatesburg aquifer have horizontal hydraulic conductivities of about 1 foot per day. Regional directions of ground-water flow are toward the major streams with Clover Creek as the major discharge point for ground water in the east. Ground-water flow to the well fields is anisotropic with a 5:1 preferential horizontal direction along strike of the axial fold of the anticline. Thus, the zone of contribution of ground water to the well fields is elongate in a north-south direction along the anticline axis, with the majority of the flow to the well fields originating from the south. Human activity in the areal extent of the zone of contribution to the well fields was the source of contaminants. The areal extent of the zone of contribution included both urban areas in the Borough and a large amount of agricultural land. By relating results of flow simulation, natural geochemistry, and analyses of anthropogenic (human-made) contaminants, the source areas for water and contaminants were determined with more confidence than by using only flow simulation. Analysis of natural geochemistry identified water sources from both limestone and dolomite aquifers. Geochemistry results also indicated fractures, not conduits, were the dominant source of water from aquifers; however, quantitative source identification was not possible. Chemical ratios of chloride and bromide were useful to show that all samples of ground water had sources with chemical contributions from land surface. Nitrogen isotope ratio analysis indicated animal manure as the possible primary source of nitrate in most ground water. Some of the nitrate in ground water had chemical fertilizer as a source. At the Wineland well field, chemical fertilizer was likely the source of nitrate. The nitrate in water from the Hershberger well field was from a mixture of fertilizer and animal-manure sources. Human sewage was ruled out as a major source of nitrate in water from the municipal wells by results showing 1) wastewater compounds in sewage were rarely detected and 2) a mass-balance calculation indicating the small contribution of nitrogen that could be attributed to septic systems.

Fine particle receptor modeling in the atmosphere of Mexico City.

PubMed

Vega, Elizabeth; Lowenthal, Douglas; Ruiz, Hugo; Reyes, Elizabeth; Watson, John G; Chow, Judith C; Viana, Mar; Querol, Xavier; Alastuey, Andrés

2009-12-01

Source apportionment analyses were carried out by means of receptor modeling techniques to determine the contribution of major fine particulate matter (PM2.5) sources found at six sites in Mexico City. Thirty-six source profiles were determined within Mexico City to establish the fingerprints of particulate matter sources. Additionally, the profiles under the same source category were averaged using cluster analysis and the fingerprints of 10 sources were included. Before application of the chemical mass balance (CMB), several tests were carried out to determine the best combination of source profiles and species used for the fitting. CMB results showed significant spatial variations in source contributions among the six sites that are influenced by local soil types and land use. On average, 24-hr PM2.5 concentrations were dominated by mobile source emissions (45%), followed by secondary inorganic aerosols (16%) and geological material (17%). Industrial emissions representing oil combustion and incineration contributed less than 5%, and their contribution was higher at the industrial areas of Tlalnepantla (11%) and Xalostoc (8%). Other sources such as cooking, biomass burning, and oil fuel combustion were identified at lower levels. A second receptor model (principal component analysis, [PCA]) was subsequently applied to three of the monitoring sites for comparison purposes. Although differences were obtained between source contributions, results evidence the advantages of the combined use of different receptor modeling techniques for source apportionment, given the complementary nature of their results. Further research is needed in this direction to reach a better agreement between the estimated source contributions to the particulate matter mass.

Rainfall Threshold Assessment Corresponding to the Maximum Allowable Turbidity for Source Water.

PubMed

Fan, Shu-Kai S; Kuan, Wen-Hui; Fan, Chihhao; Chen, Chiu-Yang

2016-12-01

  This study aims to assess the upstream rainfall thresholds corresponding to the maximum allowable turbidity of source water, using monitoring data and artificial neural network computation. The Taipei Water Source Domain was selected as the study area, and the upstream rainfall records were collected for statistical analysis. Using analysis of variance (ANOVA), the cumulative rainfall records of one-day Ping-lin, two-day Ping-lin, two-day Tong-hou, one-day Guie-shan, and one-day Tai-ping (rainfall in the previous 24 or 48 hours at the named weather stations) were found to be the five most significant parameters for downstream turbidity development. An artificial neural network model was constructed to predict the downstream turbidity in the area investigated. The observed and model-calculated turbidity data were applied to assess the rainfall thresholds in the studied area. By setting preselected turbidity criteria, the upstream rainfall thresholds for these statistically determined rain gauge stations were calculated.

Aethalometer

DOEpatents

Hansen, Anthony D.

1990-01-01

An improved aethalometer (10) having a single light source (18) and a single light detector (20) and two light paths (21, 22) from the light source (18) to the light detector (20). A quartz fiber filter (13) is inserted in the device, the filter (13) having a collection area (23) in one light path (21) and a reference area (24) in the other light path (22). A gas flow path (46) through the aethalometer housing (11) allows ambient air to flow through the collection area (23) of the filter (13) so that aerosol particles can be collected on the filter. A rotating disk (31) with an opening (33) therethrough allows light for the light source (18) to pass alternately through the two light paths (21, 22). The voltage output of the detector (20) is applied to a VCO (52) and the VCO pulses for light transmission separately through the two light paths (21, 22 ) are counted and compared to determine the absorption coefficient of the collected aerosol particles.

Mobile Methane Monitoring Surveys of the Pinedale Anticline Development in the Upper Green River Basin of Wyoming

NASA Astrophysics Data System (ADS)

Field, R. A.; Soltis, J.; Murphy, S. M.; Montague, D. C.

2013-12-01

Methane emissions from the oil and gas sector have become part of a wider debate of the magnitude of climate change impacts from different fossil fuels. This debate is contentious, as a wide range of estimates of development area leakage rates have been postulated. Here we present the results of mobile monitoring performed in the Pinedale Anticline, WY (PAPA) development. A 4-hour circuit upwind, downwind and within the development was designed to determine methane distributions relative to background concentrations. The circuit was repeated thirty-two times to assess the influence of meteorology and emission sources upon measured values. Figure 1 is a composite of methane data for the project. This pilot project enabled identification of areas and emission sources for subsequent plume quantification studies planned for 2014. Here we present the finding of the circuits through mapping and site comparisons. Along with the methane measurements, mobile ozone and oxides of nitrogen observations were also performed, thereby facilitating a better understanding of the phenomenon of wintertime ground level ozone. Building upon surveys from 2012, we also carried out canister measurements of VOC at selected sites to demonstrate the importance of relating methane and selected VOC concentrations when identifying variations in the contributions of emission sources to ambient measurements. While methane and C2 to C5 alkanes elevations are widespread and highly correlated, those of higher molecular weight VOC, in particular benzene, toluene and xylene isomers, show the importance of emission sources other than wet gas leakage. We discuss the utility of 3D visualization of methane data for illustrating the distribution of leakage relative to emission sources. The influence of emission sources and meteorology upon the data is explored through a comparative analysis of the circuit data. This assessment sets the foundation for planned plume quantification. Finally we compare the mobile data with 1-minute data from the Wyoming DEQ site at Boulder, WY, to determine how well the site represents conditions in the surrounding area. Effective policy decisions require better coupling of air quality measurements and emission inventories. We outline an approach that links regulatory network site data with mobile monitoring and plume quantification that should reduce uncertainty for determining the magnitude of methane emissions from oil and gas sources. Pinedale Anticline methane concentrations for mobile monitoring circuits 2/12/2013 to 3/8/2013

Determination of carbonyls and their sources in three sites of the metropolitan area of Costa Rica, Central America.

PubMed

Murillo, Jorge Herrera; Marín, José Félix Rojas; Román, Susana Rodríguez

2012-01-01

Ambient levels of carbonyl compounds and their possible sources were studied at three places in the metropolitan area of Costa Rica, including a residential, an industrial, and a commercial downtown area with high vehicular flow, during the periods of April-May and September-December 2009. Fifteen carbonyl compounds were identified in the ambient air, of which acetone was the most abundant carbonyl, followed by formaldehyde and acetaldehyde. Concentrations were highest in rainy season at all sites and lower in dry season. These decreases in concentration are explained by the influences of both photochemical reactions and local meteorological conditions. The strong correlation between C1-C2 and C3 indicated a common origin for these carbonyls. The C1/C2 ratios varied between 0.49 to 1.05, values which can be considered typical of an urban area.

Atmospheric heavy metal deposition in Northern Vietnam: Hanoi and Thainguyen case study using the moss biomonitoring technique, INAA and AAS.

PubMed

Viet, Hung Nguyen; Frontasyeva, Marina Vladimirovna; Thi, Thu My Trinh; Gilbert, Daniel; Bernard, Nadine

2010-06-01

The moss technique is widely used to monitor atmospheric deposition of heavy metals in many countries in Europe, whereas this technique is scarcely used in Asia. To implement this international reliable and cheap methodology in the Asian countries, it is necessary to find proper moss types typical for the Asian environment and suitable for the biomonitoring purposes. Such a case study was undertaken in Vietnam for assessing the environmental situation in strongly contaminated areas using local species of moss Barbula indica. The study is focused on two areas characterized by different pollution sources: the Hanoi urban area and the Thainguyen metallurgical zone. Fifty-four moss samples were collected there according to standard sampling procedure adopted in Europe. Two complementary analytical techniques, atomic absorption spectrometry (AAS) and instrumental neutron activation analysis (INAA), were used for determination of elemental concentrations in moss samples. To characterize the pollution sources, multivariate statistical analysis was applied. A total of 38 metal elements were determined in the moss by the two analytical techniques. The results of descriptive statistics of metal concentration in moss from the city center and periphery of Hanoi determined by AAS are presented. The similar results for moss from Thainguyen province determined by INAA and AAS are given also. A comparison of mean elemental concentrations in moss of this work with those in different environmental conditions of other authors provides reasonable information on heavy metal atmospheric deposition levels. Factor loadings and factor scores were used to identify and apportion contamination sources at the sampling sites. The values of percentage of total of factors show two highly different types of pollution in the two examined areas-the Hanoi pollution composition with high portion of urban-traffic activity and soil dust (62%), and the one of Thainguyen with factors related to industrial activities (75%). Besides, the scatter of factors in factor planes represents the greater diversity of activities in Hanoi than in Thainguyen. Good relationship between the result of factor analysis and the pollution sources evidences that the moss technique is a potential method to assess the air quality in Vietnam. Moss B. indica widely distributed in Vietnam and Indo-China is shown to be a reliable bryophyte for biomonitoring purposes in sub-tropic and tropic climate. However, the necessity of moss interspecies calibration is obvious for further studies in the area to provide results compatible with those for other Asian countries and Europe.

Origin of fecal contamination in waters from contrasted areas: stanols as Microbial Source Tracking markers.

PubMed

Derrien, M; Jardé, E; Gruau, G; Pourcher, A M; Gourmelon, M; Jadas-Hécart, A; Pierson Wickmann, A C

2012-09-01

Improving the microbiological quality of coastal and river waters relies on the development of reliable markers that are capable of determining sources of fecal pollution. Recently, a principal component analysis (PCA) method based on six stanol compounds (i.e. 5β-cholestan-3β-ol (coprostanol), 5β-cholestan-3α-ol (epicoprostanol), 24-methyl-5α-cholestan-3β-ol (campestanol), 24-ethyl-5α-cholestan-3β-ol (sitostanol), 24-ethyl-5β-cholestan-3β-ol (24-ethylcoprostanol) and 24-ethyl-5β-cholestan-3α-ol (24-ethylepicoprostanol)) was shown to be suitable for distinguishing between porcine and bovine feces. In this study, we tested if this PCA method, using the above six stanols, could be used as a tool in "Microbial Source Tracking (MST)" methods in water from areas of intensive agriculture where diffuse fecal contamination is often marked by the co-existence of human and animal sources. In particular, well-defined and stable clusters were found in PCA score plots clustering samples of "pure" human, bovine and porcine feces along with runoff and diluted waters in which the source of contamination is known. A good consistency was also observed between the source assignments made by the 6-stanol-based PCA method and the microbial markers for river waters contaminated by fecal matter of unknown origin. More generally, the tests conducted in this study argue for the addition of the PCA method based on six stanols in the MST toolbox to help identify fecal contamination sources. The data presented in this study show that this addition would improve the determination of fecal contamination sources when the contamination levels are low to moderate. Copyright © 2012 Elsevier Ltd. All rights reserved.

13 CFR 121.303 - What size procedures are used by SBA before it makes a formal size determination?

Code of Federal Regulations, 2010 CFR

2010-01-01

... source. (b) A small business investment company, a development company, a surety bond company, or a... area in which the headquarters of the applicant is located, regardless of the location of the parent company or affiliates. For disaster loan assistance, the request for a size determination must be made to...

Seawater quality assessment and identification of pollution sources along the central coastal area of Gabes Gulf (SE Tunisia): Evidence of industrial impact and implications for marine environment protection.

PubMed

El Zrelli, Radhouan; Rabaoui, Lotfi; Ben Alaya, Mohsen; Daghbouj, Nabil; Castet, Sylvie; Besson, Philippe; Michel, Sylvain; Bejaoui, Nejla; Courjault-Radé, Pierre

2018-02-01

Temperature, pH and trace elements (F, P, Cr, Cu, Zn, Cd, and Pb) contents were determined in 16 stations as well as in 2 industrial and 2 domestic discharge sources, in the central coastal area of the Gulf of Gabes. Compared to the northern and southern areas of the study area, the highest contents of contaminants were reached in the central area which hosts the coastal industrial complex. The seawater in this central area was also found to be acid and of higher temperature. Based on the Water Pollution Index results, an increasing degradation gradient of the seawater quality was revealed from northern and/or southern stations to central ones, categorized as 'strongly to seriously affected'. Phosphogypsum wastes dumped by the Tunisian Chemical Group (GCT) seem to have continuously degraded the seawater quality in the study area. A rapid intervention is needed to stop the effects on the marine environment. Copyright © 2017 Elsevier Ltd. All rights reserved.

The study of the physics of cometary nuclei

NASA Technical Reports Server (NTRS)

Whipple, F. L.

1983-01-01

On the basis of the icy conglometate model of cometary nuclei various observations demonstrate the spotted nature of many or most nuclei, i.e., regions of unusual activity, either high or low. Rotation periods, spin axes and even precession of the axes have been determined. Narrow dust jets near the nuclei of some bright comets require that small sources be embedded in larger active areas. Certain evidence suggests that very dusty areas and very dusty comets may be less active, respectively, than surrounding areas or other comets.

Effects of Hurricane Surge Barrier on Hydraulic Environment, Jamaica Bay, New York; Hydraulic Model Investigation

DTIC Science & Technology

1976-09-01

the New York Harbor area and especially the Jamaica Bay complex was used to determine the effects of 13 different hurricane surge barrier plans on...vary directly with the total cross-sectional area of the naviga- tion opening and tidal openings. d. barrier plans B, C-l, C-2, and C-3 would have... plan C-1 with a conservative dye source seaward of the barrier indicated that average dye concentrations will be increased slightly in most areas in

A sediment budget from a glaciated catchment: reconciling subglacial and periglacial erosion on short timescales

NASA Astrophysics Data System (ADS)

Delaney, Ian; Gindraux, Saskia; Weidmann, Yvo; Bauder, Andreas

2017-04-01

Glaciated catchments are known to expel great amounts of sediment, particularly during periods of climatic perturbation. Sediment in these catchments either originates subglacially, where it is eroded by pressurized water below the glacier, or from periglacial areas, which are commonly comprised of easily erodible, unconsolidated material no longer buttressed and held in place by ice. To better forecast sediment dynamics and erosion rates in to the future, contributions of subglacial and periglacial sediment must be quantified, and the processes controlling erosion in these respective sources described. To determine the relative contributions of these sources, we examine the Griesgletscher catchment in the Swiss Alps. Its rather simplistic geometry, as well as, the presence of a proglacial reservoir that serves as a sediment trap, provides an unusually constrained environment to directly measure sediment sources and sinks in the catchment. Subtraction of three digital elevation models created from structure-from-motion and photogrammetric techniques over a one year period, from October 2015 to October 2016, were used to measured sediment flux from the proglacial area. Furthermore, comparison of bathymetries collected from the proglacial reservoir in fall of 2015 and 2016 determined total sediment flux from the entire catchment over this 10 km2time period. Data from a turbidity meter, installed below the reservoir outflow, suggest that negligible amounts of sediment leave the reservoir. Thus comparison of reservoir bathymetry and sediment fluxes from the proglacial area give estimates of the relative contribution of proglacial and subglacial sediment erosion to total catchment sedimentation. Analysis of this data suggest that while the proglacial area experiences a greater erosion rate, it is likely more sediment originates subglacially. As proglacial areas are expected to grow in area and partially stabilize, and glacial areas are predicted to shrink and possibly loose erosive capacity, these competing processes must be reconciled.

Arsenic and fluoride in the groundwater of Mexico.

PubMed

Armienta, M A; Segovia, N

2008-08-01

Concentrations of arsenic and fluoride above Mexican drinking water standards have been detected in aquifers of various areas of Mexico. This contamination has been found to be mainly caused by natural sources. However, the specific processes releasing these toxic elements into groundwater have been determined in a few zones only. Many studies, focused on arsenic-related health effects, have been performed at Comarca Lagunera in northern México. High concentrations of fluoride in water were also found in this area. The origin of the arsenic there is still controversial. Groundwater in active mining areas has been polluted by both natural and anthropogenic sources. Arsenic-rich minerals contaminate the fractured limestone aquifer at Zimapán, Central México. Tailings and deposits smelter-rich fumes polluted the shallow granular aquifer. Arsenic contamination has also been reported in the San Antonio-El Triunfo mining zone, southern Baja California, and Santa María de la Paz, in San Luis Potosí state. Even in the absence of mining activities, hydrogeochemistry and statistical techniques showed that arsenopyrite oxidation may also contaminate water, as in the case of the Independencia aquifer in the Mexican Altiplano. High concentrations of arsenic have also been detected in geothermal areas like Los Azufres, Los Humeros, and Acoculco. Prevalence of dental fluorosis was revealed by epidemiological studies in Aguascalientes and San Luis Potosí states. Presence of fluoride in water results from dissolution of acid-volcanic rocks. In Mexico, groundwater supplies most drinking water. Current knowledge and the geology of Mexico indicate the need to include arsenic and fluoride determinations in groundwater on a routine basis, and to develop interdisciplinary studies to assess the contaminant's sources in all enriched areas.

The potential use of rainwater as alternative source of drinking water by using laterite soil as natural adsorbent

NASA Astrophysics Data System (ADS)

Omar, Khairunnisa Fakhriah Mohd; Palaniandy, Puganeshwary; Adlan, Mohd Nordin; Aziz, Hamidi Abdul; Subramaniam, Ambarasi

2017-10-01

Generally, the rainwater has low concentration of pollutants, whereby it is applicable for domestic water supply. Due to the low concentration of pollutants, further treatment such as adsorption is necessary to treat the harvested rainwater as an alternative source of drinking water supply. Therefore, this research has been carried out to determine the quality of rainwater from different types of locations, which are; rural residential area, urban residential area, agricultural area, industrial area, and open surface. The rainwater sampling was carried out from September 2014 to December 2015. The parameters that have been analysed during the sampling process are chemical oxygen demand (COD), turbidity, heavy metals, and Escherichia coli (E.coli). The sampling results show that the rainwater provides low concentration of contaminants. Thus, it has high potential to be used as alternative source of potable and non potable water supply with a suitable treatment. Due to that, an experimental work contained of 86 of designated experiments for a batch study has been carried out to determine the performance of laterite soil as an adsorbent to remove pollutants that present in the rainwater (i.e. zinc, manganese, and E.coli). The operating factors involved in the experimental works are pH, mass of adsorbents, contact time, initial concentration of zinc, manganese, and E.coli. In this study, the experimental data of the batch study was analysed by developing regression model equation and analysis of variance. Perturbation plots were analysed to determine the effectiveness of the operating factors by developing response surface model, resulting that the high removals of zinc, manganese, and E.coli are 95.8%, 94.05% and 100%, respectively. Overall, this research works found out that the rainwater has a good quality as alternative source of drinking water by providing a suitable treatment. The application of laterite soil as natural adsorbent shows that it has potential to be used as the response surface model provide a good removal for zinc, manganese, and E.coli.

Evaluating the provenance of fine sediment in degraded Freshwater Pearl Mussel habitats.

NASA Astrophysics Data System (ADS)

Blake, Will; Haley, Steve; Goddard, Rupert; Stone, Peter; Broadhead, Kat

2015-04-01

Freshwater Pearl Mussels (FWPM), Margaritifera margaritifera, are among the most critically threatened freshwater bivalves worldwide. In addition to their important roles in particle processing, nutrient release, and sediment mixing, they also serve as an ideal target species for evaluation of aquatic ecosystem functioning especially in the context of their symbiotic relationship with Atlantic salmon Salmo salar and brown or sea trout Salmo trutta. Poor water quality, particularly eutrophication, and siltation are considered major contributory factors in the decline of the species hence management of diffuse water pollution from agriculture (DWPA) is a key priority in catchments that host FWPM habitats. Against this background, this study adopted a combined monitoring, surveying and sediment fingerprinting approach to determine the principal sources of fine sediment impacting FWPM habitats in the River Clun, a Special area of Conservation (SAC) for FWPMs in central western UK. Potential sediment production hotspot areas in the ca 200 km2 catchment area upstream of FWPM habitats were initially evaluated using the SCIMAP risk mapping tool. Suspended sediment monitoring was undertaken on the main stem channel where FWPM habitats are located and wet weather catchment walkover surveys undertaken along the upstream river and stream network. Within this monitoring framework, sediment fingerprinting was undertaken at two levels. The first level aimed to link primary catchment sources (cultivated and uncultivated soil, channel bank erosion, and material transported via roads and tracks) to suspended sediment output from each main tributary upstream of the FWPM beds. The second level linked silt in the FWMP beds to the main tributaries, as integrated source end-members, with the inclusion of main channel bank erosion, a notable feature of walkover surveys as an additional source. Geochemical fingerprints, determined by XRF spectroscopy, were dominated by conservative mineral-bound elements and results indicated the importance of mainstem channel bank erosion as a sediment source to the FWMP beds, in line with catchment walkover observations. In addition, broad subcatchment discrimination and subsequent sediment apportionment showed agreement with SCIMAP risk analysis for more intensively farmed areas. Fingerprinting results also suggested, however, an unexpected contribution from upland grazed areas, categorised as lower risk by SCIMAP. Detailed evaluation of primary sources in these areas was undertaken to evaluate this discrepancy and test the hypothesised importance of channel bank erosion at the subcatchment scale. The results highlight the benefits of adopting a combined monitoring, modelling and tracing approach to support targeted management of fine sediment problems. .

Effects of land disposal of municipal sewage sludge on fate of nitrates in soil, streambed sediment, and water quality

USGS Publications Warehouse

Tindall, James A.; Lull, Kenneth J.; Gaggiani, Neville G.

1994-01-01

This study was undertaken to determine the effects of sewage-sludge disposal at the Lowry sewage-sludge-disposal area, near Denver, Colorado, on ground- and surface-water quality, to determine the fate of nitrates from sludge leachate, and to determine the source areas of leachate and the potential for additional leaching from the disposal area.Sewage-sludge disposal began in 1969. Two methods were used to apply the sludge: burial and plowing. Also, the sludge was applied both in liquid and cake forms. Data in this report represent the chemical composition of soil and streambed sediment from seven soil- and four streambed-sampling sites in 1986, chemical and bacterial composition of ground water from 28 wells from 1981 to 1987, and surface-water runoff from seven water-sampling sites from 1984 to 1987. Ground water samples were obtained from alluvial and bedrock aquifers. Samples of soil, streambed sediment, ground water and surface water were obtained for onsite measurement and chemical analysis. Measurements included determination of nitrogen compounds and major cations and anions, fecal-coliform and -streptococcus bacteria, specific conductance, and pH.Thirteen wells in the alluvial aquifer in Region 3 of the study area contain water that was probably affected by sewage-sludge leachate. The plots of concentration of nitrate with time show seasonal trends and trends caused by precipitation. In addition to yearly fluctuation, there were noticeable increases in ground-water concentrations of nitrate that coincided with increased precipitation. After 3 years of annual ground-water-quality monitoring and 4 years of a quarterly sampling program, it has been determined that leachate from the sewage-sludge-disposal area caused increased nitrite plus nitrate (as nitrogen) concentration in the alluvial ground water at the site. Soil analyses from the disposal area indicate that organic nitrogen was the dominant form of nitrogen in the soil.As a result of investigations at the research site, it has been determined that a potentially large source of contamination exists in the soils of the study area owing to increased concentrations of nitrogen, sodium, calcium, magnesium, sulfate, bicarbonate, and chloride because of sewage disposal. Continued monitoring of surface and ground water for nitrogen and the other ions previously mentioned is required to assess long-term effects of municipal sludge disposal on water quality.

Effects of land disposal of municipal sewage sludge on fate of nitrates in soil, streambed sediment, and water quality

NASA Astrophysics Data System (ADS)

Tindall, James A.; Lull, Kenneth J.; Gaggiani, Neville G.

1994-12-01

This study was undertaken to determine the effects of sewage-sludge disposal at the Lowry sewage-sludge-disposal area, near Denver, Colorado, on ground- and surface-water quality, to determine the fate of nitrates from sludge leachate, and to determine the source areas of leachate and the potential for additional leaching from the disposal area. Sewage-sludge disposal began in 1969. Two methods were used to apply the sludge: burial and plowing. Also, the sludge was applied both in liquid and cake forms. Data in this report represent the chemical composition of soil and streambed sediment from seven soil- and four streambed-sampling sites in 1986, chemical and bacterial composition of ground water from 28 wells from 1981 to 1987, and surface-water runoff from seven water-sampling sites from 1984 to 1987. Ground water samples were obtained from alluvial and bedrock aquifers. Samples of soil, streambed sediment, ground water and surface water were obtained for onsite measurement and chemical analysis. Measurements included determination of nitrogen compounds and major cations and anions, fecal-coliform and -streptococcus bacteria, specific conductance, and pH. Thirteen wells in the alluvial aquifer in Region 3 of the study area contain water that was probably affected by sewage-sludge leachate. The plots of concentration of nitrate with time show seasonal trends and trends caused by precipitation. In addition to yearly fluctuation, there were noticeable increases in ground-water concentrations of nitrate that coincided with increased precipitation. After 3 years of annual ground-water-quality monitoring and 4 years of a quarterly sampling program, it has been determined that leachate from the sewage-sludge-disposal area caused increased nitrite plus nitrate (as nitrogen) concentration in the alluvial ground water at the site. Soil analyses from the disposal area indicate that organic nitrogen was the dominant form of nitrogen in the soil. As a result of investigations at the research site, it has been determined that a potentially large source of contamination exists in the soils of the study area owing to increased concentrations of nitrogen, sodium, calcium, magnesium, sulfate, bicarbonate, and chloride because of sewage disposal. Continued monitoring of surface and ground water for nitrogen and the other ions previously mentioned is required to assess long-term effects of municipal sludge disposal on water quality.

Characterization of VOC sources in an urban area based on PTR-MS measurements and receptor modelling.

PubMed

Stojić, A; Stojić, S Stanišić; Šoštarić, A; Ilić, L; Mijić, Z; Rajšić, S

2015-09-01

In this study, the concentrations of volatile organic compounds were measured by the use of proton transfer reaction mass spectrometry, together with NO x , NO, NO2, SO2, CO and PM10 and meteorological parameters in an urban area of Belgrade during winter 2014. The multivariate receptor model US EPA Unmix was applied to the obtained dataset resolving six source profiles, which can be attributed to traffic-related emissions, gasoline evaporation/oil refineries, petrochemical industry/biogenic emissions, aged plumes, solid-fuel burning and local laboratories. Besides the vehicle exhaust, accounting for 27.6 % of the total mixing ratios, industrial emissions, which are present in three out of six resolved profiles, exert a significant impact on air quality in the urban area. The major contribution of regional and long-range transport was determined for source profiles associated with petrochemical industry/biogenic emissions (40 %) and gasoline evaporation/oil refineries (29 %) using trajectory sector analysis. The concentration-weighted trajectory model was applied with the aim of resolving the spatial distribution of potential distant sources, and the results indicated that emission sources from neighbouring countries, as well as from Slovakia, Greece, Poland and Scandinavian countries, significantly contribute to the observed concentrations.

Influence of a source line position on results of EM observations applied to the diagnostics of underground heating system pipelines in urban area

NASA Astrophysics Data System (ADS)

Vetrov, A.

2009-05-01

The condition of underground constructions, communication and supply systems in the cities has to be periodically monitored and controlled in order to prevent their breakage, which can result in serious accident, especially in urban area. The most risk of damage have the underground construction made of steal such as pipelines widely used for water, gas and heat supply. To ensure the pipeline survivability it is necessary to carry out the operative and inexpensive control of pipelines condition. Induced electromagnetic methods of geophysics can be applied to provide such diagnostics. The highly developed surface in urbane area is one of cause hampering the realization of electromagnetic methods of diagnostics. The main problem is in finding of an appropriate place for the source line and electrodes on a limited surface area and their optimal position relative to the observation path to minimize their influence on observed data. Author made a number of experiments of an underground heating system pipeline diagnostics using different position of the source line and electrodes. The experiments were made on a 200 meters section over 2 meters deep pipeline. The admissible length of the source line and angle between the source line and the observation path were determined. The minimal length of the source line for the experiment conditions and accuracy made 30 meters, the maximum admissible angle departure from the perpendicular position made 30 degrees. The work was undertaken in cooperation with diagnostics company DIsSO, Saint-Petersburg, Russia.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ortiz-Ramírez, Pablo, E-mail: rapeitor@ug.uchile.cl; Ruiz, Andrés

The Monte Carlo simulation of the gamma spectroscopy systems is a common practice in these days. The most popular softwares to do this are MCNP and Geant4 codes. The intrinsic spatial efficiency method is a general and absolute method to determine the absolute efficiency of a spectroscopy system for any extended sources, but this was only demonstrated experimentally for cylindrical sources. Due to the difficulty that the preparation of sources with any shape represents, the simplest way to do this is by the simulation of the spectroscopy system and the source. In this work we present the validation of themore » intrinsic spatial efficiency method for sources with different geometries and for photons with an energy of 661.65 keV. In the simulation the matrix effects (the auto-attenuation effect) are not considered, therefore these results are only preliminaries. The MC simulation is carried out using the FLUKA code and the absolute efficiency of the detector is determined using two methods: the statistical count of Full Energy Peak (FEP) area (traditional method) and the intrinsic spatial efficiency method. The obtained results show total agreement between the absolute efficiencies determined by the traditional method and the intrinsic spatial efficiency method. The relative bias is lesser than 1% in all cases.« less

Groundwater vulnerability assessment in karstic aquifers using COP method.

PubMed

Bagherzadeh, Somayeh; Kalantari, Nasrollah; Nobandegani, Amir Fadaei; Derakhshan, Zahra; Conti, Gea Oliveri; Ferrante, Margherita; Malekahmadi, Roya

2018-05-02

Access to safe and reliable drinking water is amongst the important indicators of development in each society, and water scarcity is one of the challenges and limitations affecting development at national and regional levels and social life and economic activity areas. Generally, there are two types of drinking water sources: the first type is surface waters, including lakes, rivers, and streams and the second type is groundwaters existing in aquifers. Amongst aquifers, karst aquifers play an important role in supplying water sources of the world. Therefore, protecting these aquifers from pollution sources is of paramount importance. COP method is amongst the methods to investigate the intrinsic vulnerability of this type of aquifers, so that areas susceptible to contamination can be determined before being contaminated and these sources can be protected. In the present study, COP method was employed in order to spot the regions that are prone to contamination in the region. This method uses the properties of overlying geological layers above the water table (O factor), the concentration of flow (C factor), and precipitation (P factor) over the aquifer, as the parameters to assess the intrinsic vulnerability of groundwater resources. In this regard, geographical information system (GIS) and remote sensing (RS) were utilized to prepare the mentioned factors and the intrinsic vulnerability map was obtained. The results of COP method indicated that the northwest and the west of the region are highly and very vulnerable. This study indicated that regions with low vulnerability were observed in eastern areas, which accounted for 15.6% of the area. Moderate vulnerability was 40% and related to the northeast and southeast of the area. High vulnerability was 38.2% and related to western and southwestern regions. Very high vulnerability was 6.2% and related to the northwest of the area. By means of the analysis of sensitivity of the model, it was determined that the focus factor of the flow has the greatest impact on the creation of vulnerability in the region. Also, these results were validated through electrical conductivity and discharge time series of the regional springs that are located in the vulnerable zones.

Preliminary assessment of sources of nitrogen in groundwater at a biosolids-application area near Deer Trail

USGS Publications Warehouse

Yager, Tracy J.B.; McMahon, Peter B.

2012-01-01

Concentrations of dissolved nitrite plus nitrate increased fairly steadily in samples from four shallow groundwater monitoring wells after biosolids applications to nonirrigated farmland began in 1993. The U.S. Geological Survey began a preliminary assessment of sources of nitrogen in shallow groundwater at part of the biosolids-application area near Deer Trail, Colorado, in 2005 in cooperation with the Metro Wastewater Reclamation District. Possible nitrogen sources in the area include biosolids, animal manure, inorganic fertilizer, atmospheric deposition, and geologic materials (bedrock and soil). Biosolids from the Metro Wastewater Reclamation District plant in Denver and biosolids, cow manure, geologic materials (bedrock and soil), and groundwater from the study area were sampled to measure nitrogen content and nitrogen isotopic compositions of nitrate or total nitrogen. Biosolids also were leached, and the leachates were analyzed for nitrogen content and other concentrations. Geologic materials from the study area also were sampled to determine mineralogy. Estimates of nitrogen contributed from inorganic fertilizer and atmospheric deposition were calculated from other published reports. The nitrogen information from the study indicates that each of the sources contain sufficient nitrogen to potentially affect groundwater nitrate concentrations. Natural processes can transform the nitrogen in any of the sources to nitrate in the groundwater. Load calculations indicate that animal manure, inorganic fertilizer, or atmospheric deposition could have contributed the largest nitrogen load to the study area in the 13 years before biosolids applications began, but biosolids likely contributed the largest nitrogen load to the study area in the 13 years after biosolids applications began. Various approaches provided insights into sources of nitrate in the groundwater samples from 2005. The isotopic data indicate that, of the source materials considered, biosolids and (or) animal manure were the most likely sources of nitrate in the wells at the time of sampling (2005), and that inorganic fertilizer, atmospheric deposition, and geologic materials were not substantial sources of nitrate in the wells in 2005. The large total nitrogen content of the biosolids and animal-manure samples and biosolids leachates also indicates that the biosolids and animal manure had potential to leach nitrogen and produce large dissolved nitrate concentrations in groundwater. The available data, however, could not be used to distinguish between biosolids or manure as the dominant source of nitrate in the groundwater because the nitrogen isotopic composition of the two materials is similar. Major-ion data also could not be used to distinguish between biosolids or manure as the dominant source of nitrate in the groundwater because the major-ion composition (as well as the isotopic composition) of the two materials is similar. Without additional data, chloride/bromide mass ratios do not necessarily support or refute the hypothesis that biosolids and (or) animal manure were the primary sources of nitrate in water from the study-area wells in 2005. Concentrations of water-extractable nitrate in the soil indicate that biosolids could be an important source of nitrate in the groundwater recharge. Nitrogen inventories in the soil beneath biosolids-application areas and the nitrogen-input estimates for the study area both support the comparisons of isotopic composition, which indicate that some type of human waste (such as biosolids) and (or) animal manure was the source of nitrate in groundwater sampled from the wells in 2005. The nitrogen-load estimates considered with the nitrogen isotopic data and the soil-nitrogen inventories indicate that biosolids applications likely are a major source of nitrogen to the shallow groundwater at these monitoring wells.

A Marriage Of Larval Modeling And Empirical Data: Linking Adult, Larval And Juvenile Scallops In An Estuary

NASA Astrophysics Data System (ADS)

Bayer, S.; Wahle, R.; Brooks, D. A.; Brady, D. C.

2016-02-01

The giant sea scallop, Placopecten magellanicus, is a commercially valuable sedentary broadcast spawner that occupies offshore banks and coastal bays and estuaries in the Northwest Atlantic. Although area closures have helped repopulate depleted scallop populations, little is known about whether populations at densities that yield larvae supply local or distant populations. Surveying scallop populations in the Damariscotta River estuary in Maine during the 2013 and 2014 spawning seasons, and settling out spat bags to collect settling larvae along the gradient of the estuary, we were able to compare adult densities to newly settled juvenile (`spat') abundance. Using the location where we found a high density of adults, we incorporated previously published behavior, pelagic larval duration, wind and current data into a particle dispersal model within the estuary to determine likely sinks for larvae from the 2013 and 2014 spawning seasons. Preliminary model simulations demonstrate where in the estuary swimming is effective in affecting water column position for larvae, and that most larvae are retained much closer to the mouth of the estuary than previously expected. Combining larval dispersal modeling with empirical data on adult densities and spat settlement on the scale of an embayment or estuary may be helpful in determining sources, sinks and areas that are both sources and sinks for shellfish species that are endangered or economically critical. This may aid in determining small area closures or Marine Protected Areas along coastal regions in the Gulf of Maine and beyond.

Do the enigmatic ``Infrared-Faint Radio Sources'' include pulsars?

NASA Astrophysics Data System (ADS)

Hobbs, George; Middelberg, Enno; Norris, Ray; Keith, Michael; Mao, Minnie; Champion, David

2009-04-01

The Australia Telescope Large Area Survey (ATLAS) team have surveyed seven square degrees of sky at 1.4GHz. During processing some unexpected infrared-faint radio sources (IFRS sources) were discovered. The nature of these sources is not understood, but it is possible that some of these sources may be pulsars within our own galaxy. We propose to observe the IFRS sources with steep spectral indices using standard search techniques to determine whether or not they are pulsars. A pulsar detection would 1) remove a subset of the IFRS sources from the ATLAS sample so they would not need to be observed with large optical/IR telescopes to find their hosts and 2) be intrinsically interesting as the pulsar would be a millisecond pulsar and/or have an extreme spatial velocity.

Geographical mapping of fluoride levels in drinking water sources in Nigeria.

PubMed

Akpata, Enosakhare S; Danfillo, I S; Otoh, E C; Mafeni, J O

2009-12-01

Knowledge of fluoride levels in drinking water is of importance in dental public health, yet this information is lacking, at national level, in Nigeria. To map out fluoride levels in drinking water sources in Nigeria. Fluoride levels in drinking water sources from 109 randomly selected Local Government Areas (LGAs) in the 6 Nigerian geopolitical zones were determined. From the results, maps showing LGAs with fluoride concentrations exceeding 0.3 ppm, were drawn. ANOVA and t-test were used to determine the significance of the differences between the fluoride levels in the drinking water sources. Fluoride levels were low in most parts of the country, being 0.3 ppm or less in 62% of the LGAs. Fluoride concentrations were generally higher in North Central geopolitical zone, than the other zones in the country (p<0.05). In a few drinking water sources, fluoride concentrations exceeded 1.5 ppm, but was as high as 6.7 ppm in one well. Only 9% of the water sources were from waterworks. Most of the water sources in Nigeria contained low fluoride levels; but few had excessive concentrations and need to be partially defluoridated, or else alternative sources of drinking water provided for the community.

Determining the contribution of long-range transport, regional and local source areas, to PM10 mass loading in Hessen, Germany using a novel multi-receptor based statistical approach

NASA Astrophysics Data System (ADS)

Garg, Saryu; Sinha, Baerbel

2017-10-01

This study uses two newly developed statistical source apportionment models, MuSAM and MuReSAM, to perform quantitative statistical source apportionment of PM10 at multiple receptor sites in South Hessen. MuSAM uses multi-site back trajectory data to quantify the contribution of long-range transport, while MuReSAM uses wind speed and direction as proxy for regional transport and quantifies the contribution of regional source areas. On average, between 7.8 and 9.1 μg/m3 of PM10 (∼50%) at receptor sites in South Hessen is contributed by long-range transport. The dominant source regions are Eastern, South Eastern, and Southern Europe. 32% of the PM10 at receptor sites in South Hessen is contributed by regional source areas (2.8-9.41 μg/m3). This fraction varies from <20% at remote sites to >40% for urban stations. Sources located within a 2 km radius around the receptor site are responsible for 7%-20% of the total PM10 mass (0.7-4.4 μg/m3). The perturbation study of the traffic flow due to the closing and reopening of the Schiersteiner Brücke revealed that the contribution of the bridge to PM10 mass loadings at two nearby receptor sites increased by approximately 120% after it reopened and became a bottleneck, although in absolute terms, the increase is small.

Characterization of the near-source population around five ...

EPA Pesticide Factsheets

Many ports are currently preparing for increased freight traffic, which may result in elevated local air pollution in areas near the port and freight transportation corridors. In this study, a geographical information system (GIS) analysis of areas surrounding five ports – Port of New York and New Jersey, Port of Virginia, Port of Savannah, Port of Miami, and Port of Houston – was conducted to characterize the population that might be affected by air emissions from the freight transportation network and to determine which sources had the potential to affect the most people. Defining “near-source” populations as living within 300 m of the freight transportation network, namely the port and associated truck routes, railroads, and intermodal facilities (e. g. rail yards and warehouses); near-source populations ranged from 37,000 to over a million within 10 km of a port. At the ports considered, the population living within 300 m of the port boundary constituted <10 % of the total near-source population. Sensitive population exposure was also indicated, such as the 81 day care centers and K-12 schools in near-source environments within 2 km of the Port of New York and New Jersey. Minority groups constituted 55 % to 85 % of the near-source populations in the five port areas. For four of the five ports, the mean and median income of the near-source population was lower and the minority percentage was higher than the population living adjacent to the near-sou

Tidal river sediments in the Washington, D.C. area. 11. Distribution and sources of organic containmants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wade, T.L.; Velinsky, D.J.; Reinharz, E.

1994-06-01

Concentrations of aliphatic, aromatic, and chlorinated hydrocarbons were determined from 33 surface-sediment samples taken from the Tidal Basin, Washington Ship Channel, and the Anacostia and Potomac rivers in Washington, D.C. In conjunction with these samples, selected storm sewers and outfalls also were sampled to help elucidate general sources of contamination to the area. All of the sediments contained detectable concentrations of aliphatic and aromatic hydrocarbons, DDT (total dichlorodiphenytrichloroethande), DDE (dichlorodiphenyldichloroethene), DDD (dichlorodiphenyldichloroethane), PCBx (total polychlorinated biphenyls) and total chlordanes (oxy-, {alpha}-, and {gamma}-chlordane and cis + trans-nonachlor). Sediment concentrations of most contaminants were highest in the Anacostia River just downstreammore » of the Washington Navy Yard, except for total chlordane, which appeared to have upstream sources in addition to storm and combined sewer runoff. This area has the highest number of storm and combined sewer outfalls in the river. Potomac River stations had lower concentrations than other stations. Polycyclic aromatic hydrocarbons, saturated hydrocarbons, and the unresolved complex mixture (UCM) distributions reflect mixtures of combustion products and direct discharges of petroleum products. Sources of PCBs appear to be related to specific outfalls, while hydrocarbon inputs, especially PAHs, are diffuse, and may be related to street runoff. This study indicates that in large urban areas, nonpoint sources deliver substantial amounts of contaminants to ecosystems through storm and combined sewer systems, and control of these inputs must be addressed. 33 refs., 6 figs., 3 tabs.« less

Combining chemometric tools for assessing hazard sources and factors acting simultaneously in contaminated areas. Case study: "Mar Piccolo" Taranto (South Italy).

PubMed

Mali, Matilda; Dell'Anna, Maria Michela; Notarnicola, Michele; Damiani, Leonardo; Mastrorilli, Piero

2017-10-01

Almost all marine coastal ecosystems possess complex structural and dynamic characteristics, which are influenced by anthropogenic causes and natural processes as well. Revealing the impact of sources and factors controlling the spatial distributions of contaminants within highly polluted areas is a fundamental propaedeutic step of their quality evaluation. Combination of different pattern recognition techniques, applied to one of the most polluted Mediterranean coastal basin, resulted in a more reliable hazard assessment. PCA/CA and factorial ANOVA were exploited as complementary techniques for apprehending the impact of multi-sources and multi-factors acting simultaneously and leading to similarities or differences in the spatial contamination pattern. The combination of PCA/CA and factorial ANOVA allowed, on one hand to determine the main processes and factors controlling the contamination trend within different layers and different basins, and, on the other hand, to ascertain possible synergistic effects. This approach showed the significance of a spatially representative overview given by the combination of PCA-CA/ANOVA in inferring the historical anthropogenic sources loading on the area. Copyright © 2017 Elsevier Ltd. All rights reserved.

Interplanetary scintillation observations with the Cocoa Cross radio telescope

NASA Technical Reports Server (NTRS)

Cronyn, W. M.; Shawhan, S. D.; Erskine, F. T.; Huneke, A. H.; Mitchell, D. G.

1976-01-01

Physical and electrical parameters for the 34.3-MHz Cocoa Cross radio telescope are given. The telescope is dedicated to the determination of solar-wind characteristics in and out of the ecliptic plane through measurement of electron-density irregularity structure as determined from IPS (interplanetary scintillation) of natural radio sources. The collecting area (72,000 sq m), angular resolution (0.4 deg EW by 0.6 deg NS), and spatial extent (1.3 km EW by 0.8 km NS) make the telescope well suited for measurements of IPS index and frequency scale for hundreds of weak radio sources without serious confusion effects.

Determination of the Sources of Radar Scattering

NASA Technical Reports Server (NTRS)

Moore, R. K.; Zoughi, R.

1984-01-01

Fine-resolution radar backscattering measurements were proposed to determine the backscattering sources in various vegetation canopies and surface targets. The results were then used to improve the existing theoretical models of terrain scattering, and also to enhance understanding of the radar signal observed by an imaging radar over a vegetated area. Various experiments were performed on targets such as corn, milo, soybeans, grass, asphalt pavements, soil and concrete walkways. Due to the lack of available references on measurements of this type, the obtained results will be used primarily as a foundation or future experiments. The constituent backscattering characteristics of the vegetation canopies was also examined.

Theoretical and experimental studies in ultraviolet solar physics

NASA Technical Reports Server (NTRS)

Parkinson, W. H.; Reeves, E. M.

1975-01-01

The processes and parameters in atomic and molecular physics that are relevant to solar physics are investigated. The areas covered include: (1) measurement of atomic and molecular parameters that contribute to discrete and continous sources of opacity and abundance determinations in the sun; (2) line broadening and scattering phenomena; and (3) development of an ion beam spectroscopic source which is used for the measurement of electron excitation cross sections of transition region and coronal ions.

A search for AGN activity in Infrared-Faint Radio Sources (IFRS)

NASA Astrophysics Data System (ADS)

Lenc, Emil; Middelberg, Enno; Norris, Ray; Mao, Minnie

2009-04-01

We propose to observe a large sample of radio sources from the ATLAS (Australia Telescope Large Area Survey) source catalogue with the LBA, to determine their compactness. The sample consists of 36 sources with no counterpart in the co-located SWIRE survey (3.6 um to 160 um), carried out with the Spitzer Space Telescope. This rare class of sources, dubber Infrared-Faint Radio Sources (IFRS), is inconsistent with current galaxy evolution models. VLBI observations are an essential way to obtain further clues on what these objects are and why they are hidden from infrared observations. We will measure the flux densities on long baselines to determine their compactness. Only five IFRS have been previously targeted with VLBI observations (resulting in two detections). We propose using single baseline (Parkes-ATCA) eVLBI observations with the LBA at 1 Gbps to maximise sensitivity. With the observations proposed here we will increase the number of VLBI-observed IFRS from 5 to 36, allowing us to draw statistical conclusions about this intriguing new class of objects.

A search for AGN activity in Infrared-Faint Radio Sources (IFRS)

NASA Astrophysics Data System (ADS)

Lenc, Emil; Middelberg, Enno; Norris, Ray; Mao, Minnie

2010-04-01

We propose to observe a large sample of radio sources from the ATLAS (Australia Telescope Large Area Survey) source catalogue with the LBA, to determine their compactness. The sample consists of 36 sources with no counterpart in the co-located SWIRE survey (3.6 um to 160 um), carried out with the Spitzer Space Telescope. This rare class of sources, dubber Infrared-Faint Radio Sources (IFRS), is inconsistent with current galaxy evolution models. VLBI observations are an essential way to obtain further clues on what these objects are and why they are hidden from infrared observations. We will measure the flux densities on long baselines to determine their compactness. Only five IFRS have been previously targeted with VLBI observations (resulting in two detections). We propose using single baseline (Parkes-ATCA) eVLBI observations with the LBA at 1 Gbps to maximise sensitivity. With the observations proposed here we will increase the number of VLBI-observed IFRS from 5 to 36, allowing us to draw statistical conclusions about this intriguing new class of objects.

2010 Annual Summary Report for the Area 3 and Area 5 Radioactive Management Sites at the Nevada National Security Site, Nye County, Nevada

DOE Office of Scientific and Technical Information (OSTI.GOV)

NSTec Environmental Management

2011-03-01

The U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office performed an annual review of the Area 3 and Area 5 Radioactive Waste Management Site (RWMS) Performance Assessments (PAs) and Composite Analyses (CAs) in fiscal year (FY) 2010. This annual summary report presents data and conclusions from the FY 2010 review, and determines the adequacy of the PAs and CAs. Operational factors (e.g., waste forms and containers, facility design, and waste receipts), closure plans, monitoring results, and research and development (R&D) activities were reviewed to determine the adequacy of the PAs. Likewise, the environmental restoration activities at themore » Nevada National Security Site (NNSS) (formerly the Nevada Test Site) relevant to the sources of residual radioactive material that are considered in the CAs, the land-use planning, and the results of the environmental monitoring and R&D activities were reviewed to determine the adequacy of the CAs.« less

Polybrominated diphenyl ethers in surface soils from e-waste recycling areas and industrial areas in South China: concentration levels, congener profile, and inventory.

PubMed

Gao, Shutao; Hong, Jianwen; Yu, Zhiqiang; Wang, Jingzhi; Yang, Guoyi; Sheng, Guoying; Fu, Jiamo

2011-12-01

Polybrominated diphenyl ethers (PBDEs) were determined in 60 surface soils from two e-waste recycling sites (Qingyuan and Guiyu, China) and their surrounding areas to assess the extent and influence of PBDEs from e-waste recycling sites on the surrounding areas. A total of 32 surface soils from industrial areas in South China were also investigated for comparison. The mean concentrations of total PBDEs in the e-waste recycling sites of Guiyu and Qingyuan were 2,909 and 3,230 ng/g dry weight, respectively, whereas the PBDE concentrations decreased dramatically (1-2 orders of magnitude) with increasing distance from the recycling site, suggesting that the e-waste recycling activities were the major source of PBDEs in the surrounding areas. Decabromodiphenyl ethers accounted for 77.0 to 85.8% of total PBDEs in e-waste recycling areas, whereas it accounted for 90.2% in industrial areas. Principal component analysis showed that the major source of PBDEs in e-waste recycling areas were a combination of penta-, octa-, and deca-BDE commercial formulations, whereas deca-BDE commercial formulations were the major source of PBDE congeners in industrial areas. The inventories of PBDEs gave preliminary estimates of 6.22 tons and 13.4 tons for the e-waste recycling areas and industrial areas. The results suggested that significantly higher PBDEs in the e-waste recycling sites have already affected surrounding areas negatively within a relatively large distance. Because of the environmental persistence, bioaccumulation, and toxicity of PBDEs, improving the recycling techniques employed at such facilities and developing e-waste management policies are necessary. Copyright © 2011 SETAC.

Understanding handpump sustainability: Determinants of rural water source functionality in the Greater Afram Plains region of Ghana.

PubMed

Fisher, Michael B; Shields, Katherine F; Chan, Terence U; Christenson, Elizabeth; Cronk, Ryan D; Leker, Hannah; Samani, Destina; Apoya, Patrick; Lutz, Alexandra; Bartram, Jamie

2015-10-01

Safe drinking water is critical to human health and development. In rural sub-Saharan Africa, most improved water sources are boreholes with handpumps; studies suggest that up to one third of these handpumps are nonfunctional at any given time. This work presents findings from a secondary analysis of cross-sectional data from 1509 water sources in 570 communities in the rural Greater Afram Plains (GAP) region of Ghana; one of the largest studies of its kind. 79.4% of enumerated water sources were functional when visited; in multivariable regressions, functionality depended on source age, management, tariff collection, the number of other sources in the community, and the district. A Bayesian network (BN) model developed using the same data set found strong dependencies of functionality on implementer, pump type, management, and the availability of tools, with synergistic effects from management determinants on functionality, increasing the likelihood of a source being functional from a baseline of 72% to more than 97% with optimal management and available tools. We suggest that functionality may be a dynamic equilibrium between regular breakdowns and repairs, with management a key determinant of repair rate. Management variables may interact synergistically in ways better captured by BN analysis than by logistic regressions. These qualitative findings may prove generalizable beyond the study area, and may offer new approaches to understanding and increasing handpump functionality and safe water access.

Effects of habitat isolation on the recovery of fish assemblages in experimentally defaunated stream pools in Arkansas

Treesearch

David George Lonzarich; Melvin L. Warren; Mary Ruth Elger Lonzrich

1998-01-01

The authors removed fish from pools in two Arkansas streams to determine recolonization rates and the effects of isolation (i.e., riffle length, riffle depth, distance to large source pools, and location), pool area, and assemblage size on recovery. To determine pool-specific recovery rates, the authors repeatedly snorkeled 12 pools over a 40-day recovery period....

Coseismic source model of the 2003 Mw 6.8 Chengkung earthquake, Taiwan, determined from GPS measurements

USGS Publications Warehouse

Ching, K.-E.; Rau, R.-J.; Zeng, Y.

2007-01-01

A coseismic source model of the 2003 Mw 6.8 Chengkung, Taiwan, earthquake was well determined with 213 GPS stations, providing a unique opportunity to study the characteristics of coseismic displacements of a high-angle buried reverse fault. Horizontal coseismic displacements show fault-normal shortening across the fault trace. Displacements on the hanging wall reveal fault-parallel and fault-normal lengthening. The largest horizontal and vertical GPS displacements reached 153 and 302 mm, respectively, in the middle part of the network. Fault geometry and slip distribution were determined by inverting GPS data using a three-dimensional (3-D) layered-elastic dislocation model. The slip is mainly concentrated within a 44 ?? 14 km slip patch centered at 15 km depth with peak amplitude of 126.6 cm. Results from 3-D forward-elastic model tests indicate that the dome-shaped folding on the hanging wall is reproduced with fault dips greater than 40??. Compared with the rupture area and average slip from slow slip earthquakes and a compilation of finite source models of 18 earthquakes, the Chengkung earthquake generated a larger rupture area and a lower stress drop, suggesting lower than average friction. Hence the Chengkung earthquake seems to be a transitional example between regular and slow slip earthquakes. The coseismic source model of this event indicates that the Chihshang fault is divided into a creeping segment in the north and the locked segment in the south. An average recurrence interval of 50 years for a magnitude 6.8 earthquake was estimated for the southern fault segment. Copyright 2007 by the American Geophysical Union.

A review on the sources and spatial-temporal distributions of Pb in Jiaozhou Bay

NASA Astrophysics Data System (ADS)

Yang, Dongfang; Zhang, Jie; Wang, Ming; Zhu, Sixi; Wu, Yunjie

2017-12-01

This paper provided a review on the source, spatial-distribution, temporal variations of Pb in Jiaozhou Bay based on investigation of Pb in surface and waters in different seasons during 1979-1983. The source strengths of Pb sources in Jiaozhou Bay were showing increasing trends, and the pollution level of Pb in this bay was slight or moderate in the early stage of reform and opening-up. Pb contents in the marine bay were mainly determined by the strength and frequency of Pb inputs from human activities, and Pb could be moving from high content areas to low content areas in the ocean interior. Surface waters in the ocean was polluted by human activities, and bottom waters was polluted by means of vertical water’s effect. The process of spatial distribution of Pb in waters was including three steps, i.e., 1), Pb was transferring to surface waters in the bay, 2) Pb was transferring to surface waters, and 3) Pb was transferring to and accumulating in bottom waters.

Complex rupture of the 13 November 2016 Mw 7.8 Kaikoura, New Zealand earthquake: Comparison of high-frequency and low-frequency observations

NASA Astrophysics Data System (ADS)

Wang, Dun; Chen, Yunguo; Wang, Qi; Mori, Jim

2018-05-01

We apply a back-projection analysis to determine the locations and timing of the sources of short-period (0.5 to 2 s) energy generated by the 13 November 2016 Mw 7.8 Kaikoura, New Zealand earthquake using data from Australian and Southeast Asia. The sources of strong short-period energy are distributed northeast of the epicenter at distances of 70 to 80 km during the time period of 70 to 80 s after the initiation. The locations of sources of long-period energy derived from global seismic and local GPS data are close to the northeastern edge of the source area, and complementary to the areas of short-period energy which occur in the converging region of the Upper Kowhal, Papatea, and Jordan Thrust faults. The obvious frequency dependence might be attributed to complexities in fault geometry, possible rupture in the subduction interface, or varying focal mechanisms during the earthquake.

Process for depositing I-125 onto a substrate used to manufacture I-125 sources

DOEpatents

McGovern, James J.; Olynyk, Joseph M.

1988-01-01

The invention relates to a process for depositing I-125 on a substrate which comprises contacting a predetermined surface area of substrate with Xe-125 gas, whereby the Xe-125 decays to I-125 and the I-125 in turn deposits as a solid on the surface of the substrate, the contact being for a time sufficient to deposit at least about 1 microcurie of I-125. I-125 is thereby deposited in a relatively uniform amount over the surface area of the substrate. The substrate is then assayed to determine how much I-125 has been deposited. The substrate is then divided into pieces of measured surface area, each piece therefore containing a measured amount of deposited I-125, and each piece can then be used in the manufacture of an I-125 source.

Storm drains are sources of human fecal pollution during dry weather in three urban southern California watersheds.

PubMed

Sercu, Bram; Van De Werfhorst, Laurie C; Murray, Jill; Holden, Patricia A

2009-01-15

Coastal urbanized areas in Southern California experience frequent beach water quality warnings in summer due to high concentrations of fecal indicator bacteria (FIB). Remediation can be difficult, as sources are often unknown. During two summers, we sampled three urbanized watersheds in Santa Barbara, CA at sites with historically high FIB concentrations to determine if human fecal matter was influencing water quality. By quantification of a human-specific Bacteroides marker (HBM), human waste was evidenced throughout both transects, and concentrations were highest in the discharges of several flowing storm drains. The HBM concentrations in storm drain discharges varied by up to 5 orders of magnitude on the same day. While the exact points of entry into the storm drain systems were not definitively determined, further inspection of the drain infrastructure suggested exfiltrating sanitary sewers as possible sources. The HBM and FIB concentrations were not consistently correlated, although the exclusive occurrence of high HBM concentrations with high FIB concentrations warrants the use of FIB analyses for a first tier of sampling. The association of human fecal pollution with dry weather drainage could be a window into a larger problem for other urbanized coastal areas with Mediterranean-type climates.

Tracing lead pollution sources in abandoned mine areas using stable Pb isotope ratios.

PubMed

Yoo, Eun-Jin; Lee, Jung-A; Park, Jae-Seon; Lee, Khanghyun; Lee, Won-Seok; Han, Jin-Seok; Choi, Jong-Woo

2014-02-01

This study focused on Pb isotope ratios of sediments in areas around an abandoned mine to determine if the ratios can be used as a source tracer. For pretreatment, sediment samples were dissolved with mixed acids, and a multi-collector inductively coupled plasma mass spectrometer (MC-ICP-MS, Nu plasma II) was used to investigate the Pb isotopic composition of the samples. The measured isotope ratios were then corrected for instrumental mass fractionation by measuring the (203)Tl/(205)Tl ratio. Repeated measurements with the NIST SRM 981 reference material showed that the precision of all ratios was below 104 ppm (±2σ) for 50 ng/g. The isotope ratios ((207)Pb/(206)Pb) found were 0.85073 ± 0.0004~0.85373 ± 0.0003 for the main stream, while they were 0.83736 ± 0.0010 for the tributary and 0.84393 ± 0.0002 for the confluence. A binary mixing equation for isotope ratios showed that the contributions of mine lead to neighboring areas were up to 60%. Therefore, Pb isotope ratios can be a good source tracer for areas around abandoned mines.

Determination of heavy metals in the ambient atmosphere.

PubMed

Suvarapu, Lakshmi Narayana; Baek, Sung-Ok

2017-01-01

Heavy metal determination in ambient air is an important task for environmental researchers because of their toxicity to human beings. Some heavy metals (hexavalent chromium (Cr), arsenic (As), cadmium (Cd) and nickel (Ni)) have been listed as carcinogens. Furthermore, heavy metals in the atmosphere can accumulate in various plants and animals and enter humans through the food chain. This article reviews the determination of heavy metals in the atmosphere in different areas of the world since 2006. The results showed that most researchers concentrated on toxic metals, such as Cr, Cd, Ni, As and lead. A few studies used plant materials as bio-monitors for the atmospheric levels of heavy metals. Some researchers found higher concentrations of heavy metals surrounding industrial areas compared with residential and/or commercial areas. Most studies reported the major sources of the particulate matter and heavy metals in the atmosphere to be industrial emissions, vehicular emissions and secondary aerosols.

Hand dug wells in Namibia: An underestimated water source or a threat to human health?

NASA Astrophysics Data System (ADS)

Wanke, H.; Nakwafila, A.; Hamutoko, J. T.; Lohe, C.; Neumbo, F.; Petrus, I.; David, A.; Beukes, H.; Masule, N.; Quinger, M.

The rural population of parts of northern and western Namibia uses hand dug wells for their domestic water supply, partly because no other source (e.g., deep tube wells) is available, but also as a substitute for pipeline water that is often perceived as being too expensive. The water quality of these wells is usually not monitored or controlled, thus a study has been carried out in four study areas in Namibia: southern Omusati/Oshana area, Okongo/Ohangwena area, Omatjete/Omaruru area, Okanguati/Kunene area. Hand dug wells have been tested for on-site parameters: electric conductivity, pH and temperature while samples were taken for major inorganic constituents and several minor and trace constituents including fluoride and nitrate. In addition a sampling campaign in 2010 included the determination of coliform bacteria and Escherichia coli. Results were classified according to the Namibian Water Guidelines. The constituents making the water unfit for human consumption are fluoride, nitrate, sulphate and total dissolved solids. Contamination by E. coli was indicated in nearly all wells that are used for livestock watering. For the Omatjete/Omaruru study area an isotope based study on the source of nitrate has indicated manure as a source. The range of recharge values obtained for the studied villages ranges from 1 mm/a to locally more than 100 mm/a. Overall the water resource in the shallow perched aquifers in the study areas is in many places inappropriate for human consumption. Treatment to improve the quality or introduction of protection measures is necessary to bring this resource to an acceptable quality according to national and/or international standards.

Pathway-based monitoring of biological effects at Great Lakes sites (Presntation)

EPA Science Inventory

The Great Lakes region suffers from degradation of water and environmental quality due to release of chemicals of emerging concern. Critical issues remain in delisting Areas of Concern (AOC) including determining sources of chemicals causing fish health impacts, relating health ...

Region 4: Kentucky Adequate Letter (7/6/2010)

EPA Pesticide Factsheets

This letter from EPA to Kentucky Energy and Environment Cabinet determined the overall mobile source emissions of direct PM2.5 and NOx in the Kentucky portion of the tri-state nonatainment area are an insignificant contributor to the air quality problem

Contamination characteristics and source apportionment of heavy metals in topsoil from an area in Xi'an city, China.

PubMed

Chen, Xiuduan; Lu, Xinwei

2018-04-30

As soil-extractable elements potentially pose ecological and health risks, identifying their contamination characteristics and sources is crucial. Therefore, to understand topsoil trace elements in the urban ring zone from the Second Ring Road to the Third Ring of Xi'an city in China, we determined the concentrations of Zn, Co, V, As, Cu, Mn, Ba, Ni and Pb, and analyzed the sources of the contamination. The results showed that the individual pollution indices of Pb, Co, Cu, Zn, Ba, Ni, Mn, As, and V were 1.79, 1.48, 1.41, 1.33, 1.20, 1.07, 1.04, 0.99, and 0.99, respectively. Evaluation with the aid of the pollution load index (PLI) indicated slight soil contamination by these elements in the study area. Using the positive matrix factorization (PMF) method, we identified four sources of contamination, namely (1) a natural source, (2) traffic emission source, (3) industrial emission source, and (4) mixed source. PMF is an effective tool for source apportionment of heavy metals in topsoil. The contribution rates of the natural source, traffic source, mixed source, and industrial source to the heavy metal contamination were specified as 25.04%, 24.71%, 24.99%, and 25.26%, respectively. Considering the above, any attempt to reduce the soil environmental cost of urban development, has to take into account the heavy metal contamination of the topsoil from industries, traffic, and other activities. Copyright © 2018 Elsevier Inc. All rights reserved.

Measuring and monitoring KIPT Neutron Source Facility Reactivity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cao, Yan; Gohar, Yousry; Zhong, Zhaopeng

2015-08-01

Argonne National Laboratory (ANL) of USA and Kharkov Institute of Physics and Technology (KIPT) of Ukraine have been collaborating on developing and constructing a neutron source facility at Kharkov, Ukraine. The facility consists of an accelerator-driven subcritical system. The accelerator has a 100 kW electron beam using 100 MeV electrons. The subcritical assembly has k eff less than 0.98. To ensure the safe operation of this neutron source facility, the reactivity of the subcritical core has to be accurately determined and continuously monitored. A technique which combines the area-ratio method and the flux-to-current ratio method is purposed to determine themore » reactivity of the KIPT subcritical assembly at various conditions. In particular, the area-ratio method can determine the absolute reactivity of the subcritical assembly in units of dollars by performing pulsed-neutron experiments. It provides reference reactivities for the flux-to-current ratio method to track and monitor the reactivity deviations from the reference state while the facility is at other operation modes. Monte Carlo simulations are performed to simulate both methods using the numerical model of the KIPT subcritical assembly. It is found that the reactivities obtained from both the area-ratio method and the flux-to-current ratio method are spatially dependent on the neutron detector locations and types. Numerical simulations also suggest optimal neutron detector locations to minimize the spatial effects in the flux-to-current ratio method. The spatial correction factors are calculated using Monte Carlo methods for both measuring methods at the selected neutron detector locations. Monte Carlo simulations are also performed to verify the accuracy of the flux-to-current ratio method in monitoring the reactivity swing during a fuel burnup cycle.« less

Media and interpersonal persuasions in the polio eradication campaign in northern Nigeria

PubMed Central

Ozohu-Suleiman, Yakubu

2010-01-01

This study is premised on the increasing global concerns over the widespread resistance to polio eradication campaign in northern Nigeria. It aims to determine the level of campaign acceptance and compare the influences of mass media and interpersonal communication sources in Zaria local government area, being one of the high-risk (WPV-endemic) areas in northern Nigeria, where campaign resistance is known to be high. By way of quantitative survey, the study utilized 10% sample of the populations of eight out of the thirteen Wards in Zaria local government area, with a response rate of 78.6%. Findings reveal close ranks between campaign acceptance and resistance in the local government area, thus further confirming the difficulties still faced in polio eradication campaign in the region. This study also indicates higher performance of Interpersonal than Mass Media sources in influencing campaign acceptance and resistance in the local communities. Contact with friends and relations was rated the most influential interpersonal sources in the acceptance and resistance decision of individuals, while newspapers and magazines were rated most influential media sources that influenced campaign resistance in the local communities. The study concludes that a polio eradication campaign, backed with competent and sufficient communication expertise that utilizes knowledge-based indigenous interpersonal communication strategies will likely result in greater community acceptance in northern Nigeria. PMID:28299036

Evaluating sources and processing of nonpoint source nitrate in a small suburban watershed in China

NASA Astrophysics Data System (ADS)

Han, Li; Huang, Minsheng; Ma, Minghai; Wei, Jinbao; Hu, Wei; Chouhan, Seema

2018-04-01

Identifying nonpoint sources of nitrate has been a long-term challenge in mixed land-use watershed. In the present study, we combine dual nitrate isotope, runoff and stream water monitoring to elucidate the nonpoint nitrate sources across land use, and determine the relative importance of biogeochemical processes for nitrate export in a small suburban watershed, Longhongjian watershed, China. Our study suggested that NH4+ fertilizer, soil NH4+, litter fall and groundwater were the main nitrate sources in Longhongjian Stream. There were large changes in nitrate sources in response to season and land use. Runoff analysis illustrated that the tea plantation and forest areas contributed to a dominated proportion of the TN export. Spatial analysis illustrated that NO3- concentration was high in the tea plantation and forest areas, and δ15N-NO3 and δ18O-NO3 were enriched in the step ponds. Temporal analysis showed high NO3- level in spring, and nitrate isotopes were enriched in summer. Study as well showed that the step ponds played an important role in mitigating nitrate pollution. Nitrification and plant uptake were the significant biogeochemical processes contributing to the nitrogen transformation, and denitrification hardly occurred in the stream.

Sources of heavy metal pollution in agricultural soils of a rapidly industrializing area in the Yangtze Delta of China.

PubMed

Xu, Xianghua; Zhao, Yongcun; Zhao, Xiaoyan; Wang, Yudong; Deng, Wenjing

2014-10-01

The rapid industrialization and urbanization in developing countries have increased pollution by heavy metals, which is a concern for human health and the environment. In this study, 230 surface soil samples (0-20cm) were collected from agricultural areas of Jiaxing, a rapidly industrializing area in the Yangtze Delta of China. Sequential Gaussian simulation (SGS) and multivariate factorial kriging analysis (FKA) were used to identify and explore the sources of heavy metal pollution for eight metals (Cu, Zn, Pb, Cr, Ni, Cd, Hg and As). Localized hot-spots of pollution were identified for Cu, Zn, Pb, Cr, Ni and Cd with area percentages of 0.48 percent, 0.58 percent, 2.84 percent, 2.41 percent, 0.74 percent, and 0.68 percent, respectively. The areas with Hg pollution covered approximately 38 percent whereas no potential pollution risk was found for As. The soil parent material and point sources of pollution had significant influences on Cr, Ni, Cu, Zn and Cd levels, except for the influence of agricultural management practices also accounted for micro-scale variations (nugget effect) for Cu and Zn pollution. Short-range (4km) diffusion processes had a significant influence on Cu levels, although they did not appear to be the dominant sources of Zn and Cd variation. The short-range diffusion pollution arising from current and historic industrial emissions and urbanization, and long-range (33km) variations in soil parent materials and/or diffusion jointly determined the current concentrations of soil Pb. The sources of Hg pollution risk may be attributed to the atmosphere deposition of industrial emission and historical use of Hg-containing pesticides. Copyright © 2014 Elsevier Inc. All rights reserved.

RESULTS FROM RECENT SCIENCE AND TECHNOLOGY INVESTIGATIONS TARGETING CHROMIUM IN THE 100D AREA HANFORD SITE WASHINGTON USA

DOE Office of Scientific and Technical Information (OSTI.GOV)

PETERSEN SW; THOMPSON KM; TONKIN MJ

2009-12-03

Sodium dichromate was used in Hanford's 100D Area during the reactor operations period of 1950 to 1964 to retard corrosion in the reactor cooling systems. Some of the sodium dichromate was released to the environment by spills and/or leaks from pipelines used to deliver the chemical to water treatment plants in the area. As a result, hexavalent chromium [Cr(VI)] has migrated through the vadose zone to the groundwater and contaminated nearly 1 km{sup 2} of groundwater to above the drinking water standard of 48 {micro}g/L. Three technology tests have recently been completed in this area to characterize the source areamore » of the plumes and evaluate alternative methods to remove Cr(VI) from groundwater. These are (1) refine the source area of the southern plume; (2) test electrocoagulation as an alternative groundwater treatment technology; and (3) test the ability to repair a permeable reactive barrier by injecting micron or nanometer-size zero-valent iron (ZVI). The projects were funded by the US Department of Energy as part of a program to interject new technologies and accelerate active cleanup. Groundwater monitoring over the past 10 years has shown that Cr(VI) concentrations in the southern plume have not significantly diminished, strongly indicating a continuing source. Eleven groundwater wells were installed in 2007 and 2008 near a suspected source area and monitored for Cr(VI) and groundwater levels. Interpretation of these data has led to refinement of the source area location to an area of less than 1 hectare (ha, 2.5 acres). Vadose zone soil samples collected during drilling did not discover significant concentrations of Cr(VI), indicating the source is localized, with a narrow wetted path from the surface to the water table. Electrocoagulation was evaluated through a pilot-scale treatability test. Over 8 million liters of groundwater were treated to Cr(VI) concentrations of {le}20 {micro}g/L. The test determined that this technology has the potential to treat Cr(VI) to these low levels, but system reliability and operational complexity rendered electrocoagulation less cost effective than the baseline technology of ion exchange. Laboratory and field tests were conducted to evaluate the practicality of injecting ZVI into the aquifer to increase the lifespan and effectiveness of an existing permeable reactive barrier. From a database of 30 ZVI materials, 6 were chosen and tested in the laboratory to determine their geochemical and physical performance under simulated 100D aquifer conditions. The best-performing ZVI was injected into the aquifer and met the primary goals of communicating the iron at least 7 meters from the injection point and reducing the aquifer to transform mobile Cr(VI) to trivalent chromium Cr(III), which is effectively immobile in the aquifer.« less

VizieR Online Data Catalog: Multiwavelength photometry of CDFS X-ray sources (Brusa+, 2009)

NASA Astrophysics Data System (ADS)

Brusa, M.; Fiore, F.; Santini, P.; Grazian, A.; Comastri, A.; Zamorani, G.; Hasinger, G.; Merloni, A.; Civano, F.; Fontana, A.; Mainieri, V.

2010-03-01

The co-evolution of host galaxies and the active black holes which reside in their centre is one of the most important topics in modern observational cosmology. Here we present a study of the properties of obscured active galactic nuclei (AGN) detected in the CDFS 1 Ms observation and their host galaxies. We limited the analysis to the MUSIC area, for which deep K-band observations obtained with ISAAC@VLT are available, ensuring accurate identifications of the counterparts of the X-ray sources as well as reliable determination of photometric redshifts and galaxy parameters, such as stellar masses and star formation rates. In particular, we: 1) refined the X-ray/infrared/optical association of 179 sources in the MUSIC area detected in the Chandra observation; 2) studied the host galaxies observed and rest frame colors and properties. (2 data files).

SEDIMENT CHEMICAL CONTAMINATION AND TOXICITY ASSOCIATED WITH A COASTAL GOLF COURSE COMPLEX.

EPA Science Inventory

The increasing density of golf courses represents a potential source of sediment contamination to nearby coastal areas, the chemical and biological magnitude of which is almost unknown. The objective of this study was to determine the concentrations of contaminants and toxicities...

Ford Motor Company NDE facility shielding design.

PubMed

Metzger, Robert L; Van Riper, Kenneth A; Jones, Martin H

2005-01-01

Ford Motor Company proposed the construction of a large non-destructive evaluation laboratory for radiography of automotive power train components. The authors were commissioned to design the shielding and to survey the completed facility for compliance with radiation doses for occupationally and non-occupationally exposed personnel. The two X-ray sources are Varian Linatron 3000 accelerators operating at 9-11 MV. One performs computed tomography of automotive transmissions, while the other does real-time radiography of operating engines and transmissions. The shield thickness for the primary barrier and all secondary barriers were determined by point-kernel techniques. Point-kernel techniques did not work well for skyshine calculations and locations where multiple sources (e.g. tube head leakage and various scatter fields) impacted doses. Shielding for these areas was determined using transport calculations. A number of MCNP [Briesmeister, J. F. MCNPCA general Monte Carlo N-particle transport code version 4B. Los Alamos National Laboratory Manual (1997)] calculations focused on skyshine estimates and the office areas. Measurements on the operational facility confirmed the shielding calculations.

Utilizing Tritium and CFC-12 to Determine Groundwater Sources in an Unconfined Aquifer Within the Abalone Cove Landslide, Palos Verdes, California

NASA Astrophysics Data System (ADS)

Difilippo, E. L.; Hammond, D. E.; Douglas, R.; Clark, J. F.; Avisar, D.; Dunker, R.

2004-12-01

The Abalone Cove landslide occupies 80 acres of an ancient landslide complex on the Palos Verdes peninsula, and was re-activated in 1979. The uphill portion of the ancient landslide complex has remained stable in historic times. Water infiltration into the slide is a short term catalyst for mass movement in the area, so it is important to determine the sources of groundwater throughout the slide mass. Water may enter the slide mass through direct percolation of recent precipitation, inflow along the head scarp of the ancient landslide or by rising through the slide plane from a deeper aquifer. The objective of this contribution is to use geochemical tracers (tritium and CFC-12) in combination with numerical modeling to constrain the importance of each of these sources. Numerical models were constructed to predict geochemical tracer concentrations throughout the basin, assuming that the only source of water to the slide mass is percolation of recent precipitation. Predicted concentrations were then compared to measured tracer values. In the ancient landslide, predicted and measured tracer concentrations are in good agreement, indicating that most of the water in this area is recent precipitation falling within the basin. Groundwater recharged uphill of the ancient landslide contributes minor flow into the complex through the head scarp, with the majority of this water flowing beneath the ancient slide plane. However, predicted tracer concentrations in the toe of the Abalone Cove landslide are not consistent with measured values. Both CFC-12 and tritium concentrations indicate that water is older than predicted and communication between the slide mass and the aquifer beneath the slide plane must occur in this area. Infiltration of this deep circulating water may exert upward hydraulic pressure on the landslide slip surface, increasing the potential for movement. This hypothesis is consistent with the observation that current movement is only occurring in the area in which tracers indicate communication with the deeper aquifer.

Probabilistic seismic hazard assessments of Sabah, east Malaysia: accounting for local earthquake activity near Ranau

NASA Astrophysics Data System (ADS)

Khalil, Amin E.; Abir, Ismail A.; Ginsos, Hanteh; Abdel Hafiez, Hesham E.; Khan, Sohail

2018-02-01

Sabah state in eastern Malaysia, unlike most of the other Malaysian states, is characterized by common seismological activity; generally an earthquake of moderate magnitude is experienced at an interval of roughly every 20 years, originating mainly from two major sources, either a local source (e.g. Ranau and Lahad Dato) or a regional source (e.g. Kalimantan and South Philippines subductions). The seismicity map of Sabah shows the presence of two zones of distinctive seismicity, these zones are near Ranau (near Kota Kinabalu) and Lahad Datu in the southeast of Sabah. The seismicity record of Ranau begins in 1991, according to the international seismicity bulletins (e.g. United States Geological Survey and the International Seismological Center), and this short record is not sufficient for seismic source characterization. Fortunately, active Quaternary fault systems are delineated in the area. Henceforth, the seismicity of the area is thus determined as line sources referring to these faults. Two main fault systems are believed to be the source of such activities; namely, the Mensaban fault zone and the Crocker fault zone in addition to some other faults in their vicinity. Seismic hazard assessments became a very important and needed study for the extensive developing projects in Sabah especially with the presence of earthquake activities. Probabilistic seismic hazard assessments are adopted for the present work since it can provide the probability of various ground motion levels during expected from future large earthquakes. The output results are presented in terms of spectral acceleration curves and uniform hazard curves for periods of 500, 1000 and 2500 years. Since this is the first time that a complete hazard study has been done for the area, the output will be a base and standard for any future strategic plans in the area.

Feasibility of Isolating Vulnerable Equipment of the Electric Power System from Sources of EMP

DTIC Science & Technology

1978-03-01

Utilities, Colorado Springs, Colorado . Mr. Hugh Chastain, LaPlata Electric Association, Durango , Colcrado. Mr. Robert Kerger and Mr. James Ware...electric power systems, and (b) single-line diagrams for powar systems In the State of Colorado . 2. Determine the feanibility of manual isolation of...vulnerable equipment upon receipt ot’ attack warning. Feasibility should be studied in Colorado Syrings (risk area) and Fr-eemont County (host area) of

Source Region Modeling of Explosions 2 and 3 from the Source Physics Experiment Using the Rayleigh Integral Method

NASA Astrophysics Data System (ADS)

Jones, K. R.; Arrowsmith, S.; Whitaker, R. W.

2012-12-01

The overall mission of the National Center for Nuclear Security (NCNS) Source Physics Experiment at the National Nuclear Security Site (SPE-N) near Las Vegas, Nevada is to improve upon and develop new physics based models for underground nuclear explosions using scaled, underground chemical explosions as proxies. To this end, we use the Rayleigh integral as an approximation to the Helmholz-Kirchoff integral, [Whitaker, 2007 and Arrowsmith et al., 2011], to model infrasound generation in the far-field. Infrasound generated by single-point explosive sources above ground can typically be treated as monopole point-sources. While the source is relatively simple, the research needed to model above ground point-sources is complicated by path effects related to the propagation of the acoustic signal and out of the scope of this study. In contrast, for explosions that occur below ground, including the SPE explosions, the source region is more complicated but the observation distances are much closer (< 5 km), thus greatly reducing the complication of path effects. In this case, elastic energy from the explosions radiates upward and spreads out, depending on depth, to a more distributed region at the surface. Due to this broad surface perturbation of the atmosphere we cannot model the source as a simple monopole point-source. Instead, we use the analogy of a piston mounted in a rigid, infinite baffle, where the surface area that moves as a result of the explosion is the piston and the surrounding region is the baffle. The area of the "piston" is determined by the depth and explosive yield of the event. In this study we look at data from SPE-N-2 and SPE-N-3. Both shots had an explosive yield of 1 ton at a depth of 45 m. We collected infrasound data with up to eight stations and 32 sensors within a 5 km radius of ground zero. To determine the area of the surface acceleration, we used data from twelve surface accelerometers installed within 100 m radially about ground zero. With the accelerometer data defining the vertical motion of the surface, we use the Rayleigh Integral Method, [Whitaker, 2007 and Arrowsmith et al., 2011], to generate a synthetic infrasound pulse to compare to the observed data. Because the phase across the "piston" is not necessarily uniform, constructive and destructive interference will change the shape of the acoustic pulse if observed directly above the source (on-axis) or perpendicular to the source (off-axis). Comparing the observed data to the synthetic data we note that the overall structure of the pulse agrees well and that the differences can be attributed to a number of possibilities, including the sensors used, topography, meteorological conditions, etc. One other potential source of error between the observed and calculated data is that we use a flat, symmetric source region for the "piston" where in reality the source region is not flat and not perfectly symmetric. A primary goal of this work is to better understand and model the relationships between surface area, depth, and yield of underground explosions.

Investigation of the potential source area, contamination pathway, and probable release history of chlorinated-solvent-contaminated groundwater at the Capital City Plume Site, Montgomery, Alabama, 2008-2010

USGS Publications Warehouse

Landmeyer, James E.; Miller, Scott; Campbell, Bruce G.; Vroblesky, Don A.; Gill, Amy C.; Clark, Athena P.

2011-01-01

Detection of the organic solvent perchloroethylene (PCE) in a shallow public-supply well in 1991 and exposure of workers in 1993 to solvent vapors during excavation activities to depths near the water table provided evidence that the shallow aquifer beneath the capital city of Montgomery, Alabama, was contaminated. Investigations conducted from 1993 to 1999 by State and Federal agencies confirmed the detection of PCE in the shallow aquifer, as well as the detection of the organic solvent trichloroethylene (TCE) and various inorganic compounds, but the source of the groundwater contamination was not determined. In May 2000 the U.S. Environmental Protection Agency proposed that the site, called the Capital City Plume (CCP) Site, be a candidate for the National Priorities List. Between 2000 and 2007, numerous site-investigation activities also did not determine the source of the groundwater contamination. In 2008, additional assessments were conducted at the CCP Site to investigate the potential source area, contamination pathway, and the probable release history of the chlorinated-solvent-contaminated groundwater. The assessments included the collection of (1) pore water in 2008 from the hyporheic zone of a creek using passive-diffusion bag samplers; (2) tissue samples in 2008 and 2009 from trees growing in areas of downtown Montgomery characterized by groundwater contamination and from trees growing in riparian zones along the Alabama River and Cypress Creek; and (3) groundwater samples in 2009 and 2010. The data collected were used to investigate the potential source area of contaminants detected in groundwater, the pathway of groundwater contamination, and constraints on the probable contaminant-release history. The data collected between 2008 and 2010 indicate that the PCE and TCE contamination of the shallow aquifer beneath the CCP Site most likely resulted from the past use and disposal of industrial wastewater from printing operations containing chlorinated solvents into the sanitary sewer and (or) stormwater systems of Montgomery. Moreover, chlorinated-solvent use and disposal occurred at least between the 1940s and 1970s at several locations occupied by printing operations. The data also indicate that PCE and TCE contamination continues to occur in the shallow subsurface near potential release areas and that PCE and TCE have been transported to the intermediate part of the shallow aquifer.

Alternative Energy Sources in Seismic Methods

NASA Astrophysics Data System (ADS)

Tün, Muammer; Pekkan, Emrah; Mutlu, Sunay; Ecevitoğlu, Berkan

2015-04-01

When the suitability of a settlement area is investigated, soil-amplification, liquefaction and fault-related hazards should be defined, and the associated risks should be clarified. For this reason, soil engineering parameters and subsurface geological structure of a new settlement area should be investigated. Especially, faults covered with quaternary alluvium; thicknesses, shear-wave velocities and geometry of subsurface sediments could lead to a soil amplification during an earthquake. Likewise, changes in shear-wave velocities along the basin are also very important. Geophysical methods can be used to determine the local soil properties. In this study, use of alternative seismic energy sources when implementing seismic reflection, seismic refraction and MASW methods in the residential areas of Eskisehir/Turkey, were discussed. Our home developed seismic energy source, EAPSG (Electrically-Fired-PS-Gun), capable to shoot 2x24 magnum shotgun cartridges at once to generate P and S waves; and our home developed WD-500 (500 kg Weight Drop) seismic energy source, mounted on a truck, were developed under a scientific research project of Anadolu University. We were able to reach up to penetration depths of 1200 m for EAPSG, and 800 m for WD-500 in our seismic reflection surveys. WD-500 seismic energy source was also used to perform MASW surveys, using 24-channel, 10 m apart, 4.5 Hz vertical geophone configuration. We were able to reach 100 m of penetration depth in MASW surveys.

Biomonitoring of airborne particulate matter emitted from a cement plant and comparison with dispersion modelling results

NASA Astrophysics Data System (ADS)

Abril, Gabriela A.; Wannaz, Eduardo D.; Mateos, Ana C.; Pignata, María L.

2014-01-01

The influence of a cement plant that incinerates industrial waste on the air quality of a region in the province of Córdoba, Argentina, was assessed by means of biomonitoring studies (effects of immission) and atmospheric dispersion (effects of emission) of PM10 with the application of the ISC3 model (Industrial Source Complex) developed by the USEPA (Environmental Protection Agency). For the biomonitoring studies, samples from the epiphyte plant Tillandsia capillaris Ruíz & Pav. f. capillaris were transplanted to the vicinities of the cement plant in order to determine the physiological damage and heavy metal accumulation (Ca, Mn, Fe, Co, Ni, Cu, Zn, Cd and Pb). For the application of the ISC3 model, point and area sources from the cement plant were considered to obtain average PM10 concentration results from the biomonitoring exposure period. This model permitted it to be determined that the emissions from the cement plant (point and area sources) were confined to the vicinities, without significant dispersion in the study area. This was also observed in the biomonitoring study, which identified Ca, Cd and Pb, pH and electric conductivity (EC) as biomarkers of this cement plant. Vehicular traffic emissions and soil re-suspension could be observed in the biomonitors, giving a more complete scenario. In this study, biomonitoring studies along with the application of atmospheric dispersion models, allowed the atmospheric pollution to be assessed in more detail.

Condensed-matter research at the Los Alamos pulsed neutron source (WNR)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eckert, J.

1982-01-01

The experimental program at the WNR in condensed matter research at present is aimed principally at utilizing the high epithermal neutron flux available at a spallation neutron source. Interesting new results have been obtained in several areas including hydrogen vibrations in metals, chemical vibrational spectroscopy and the structure of liquids. For example, extensive vibrational spectra were obtained of hydrogen in Nb which could be described in terms of a three-dimensional localized anharmonic oscillator, deuterium substitution methods were used to determine the variation with 0-0 distance of the hydrogen bending mode frequency in extremely short intramolecular hydrogen bonds, and model-independent partialmore » structure factors were determined for liquid water.« less

76 FR 71452 - Approval and Promulgation of Implementation Plans and Designation of Areas for Air Quality...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-18

...EPA is taking final action to approve a request submitted on December 18, 2009, and supplemented on December 22, 2010, from the State of North Carolina, through the North Carolina Department of Environment and Natural Resources (NC DENR), Division of Air Quality (DAQ), to redesignate the Hickory-Morganton-Lenoir fine particulate matter (PM2.5) nonattainment area (hereafter the ``Hickory Area'' or ``Area'') to attainment for the 1997 Annual PM2.5 National Ambient Air Quality Standards (NAAQS). The Hickory Area is comprised of Catawba County in its entirety. EPA's approval of the redesignation request is based on the determination that the State of North Carolina has met the criteria for redesignation to attainment set forth in the Clean Air Act (CAA or Act), including the determination that the Hickory Area has attained the 1997 Annual PM2.5 NAAQS by its applicable attainment date of April 5, 2010. Additionally, EPA is approving a revision to the North Carolina State Implementation Plan (SIP) to include the 1997 Annual PM2.5 maintenance plan for the Hickory Area that contains the new motor vehicle emission budgets (MVEBs) for nitrogen oxides (NOX) for the years 2011 and 2021 for Catawba County and the mobile insignificance determination for direct PM2.5 for the Hickory Area. This action also approves the emissions inventory submitted with the maintenance plan. Further, EPA is correcting a typographical error for the citation associated with a previous adequacy determination the Agency made for the NOX MVEBs for Catawba County and the mobile source insignificance determination for direct PM2.5 for the Hickory Area.

Sources of PM10 Air Pollution in Rural Area in the Vicinity of a Highway In Žilina Selfgoverning Region, Slovakia

NASA Astrophysics Data System (ADS)

Jandačka, Dušan

2015-05-01

Particulate matter results as an aftermath of numerous distinctive processes in the atmosphere and they become a part of everyday life. Their harmful effect and impact on the ambient environment is determined predominantly by the presence of various chemical substances and elements. The chemical composition of these particles (organic and elemental carbon, mineral dust, sea aerosols, secondary particles, especially sulphates and nitrates, heavy metals and further elements) is mainly impacted on by their origin, whereas the primary source of the particulate matter is determined and specified by the profile of chemical elements and substances. Particulate Matter (PM) may originate in various natural resources or anthropogenic sources. Among the natural sources sea salt is to be counted on, dust of the earth crust, pollen and volcanic ashes. Anthropogenic sources do include, predominantly, burning fossil fuels in the fossil-fuel power plants, local heating of households, burning liquefied fossil fuels in the combustion engines of vehicles, noncombustion related emissions as a result of vehicular traffic, resuspension of the road-traffic-related dust.

A temporal and spatial analysis of anthropogenic noise sources affecting SNMR

NASA Astrophysics Data System (ADS)

Dalgaard, E.; Christiansen, P.; Larsen, J. J.; Auken, E.

2014-11-01

One of the biggest challenges when using the surface nuclear magnetic resonance (SNMR) method in urban areas is a relatively low signal level compared to a high level of background noise. To understand the temporal and spatial behavior of anthropogenic noise sources like powerlines and electric fences, we have developed a multichannel instrument, noiseCollector (nC), which measures the full noise spectrum up to 10 kHz. Combined with advanced signal processing we can interpret the noise as seen by a SNMR instrument and also obtain insight into the more fundamental behavior of the noise. To obtain a specified acceptable noise level for a SNMR sounding the stack size can be determined by quantifying the different noise sources. Two common noise sources, electromagnetic fields stemming from powerlines and fences are analyzed and show a 1/r2 dependency in agreement with theoretical relations. A typical noise map, obtained with the nC instrument prior to a SNMR field campaign, clearly shows the location of noise sources, and thus we can efficiently determine the optimal location for the SNMR sounding from a noise perspective.

VLBI observations of Infrared-Faint Radio Sources

NASA Astrophysics Data System (ADS)

Middelberg, Enno; Phillips, Chris; Norris, Ray; Tingay, Steven

2006-10-01

We propose to observe a small sample of radio sources from the ATLAS project (ATLAS = Australia Telescope Large Area Survey) with the LBA, to determine their compactness and map their structures. The sample consists of three radio sources with no counterpart in the co-located SWIRE survey (3.6 um to 160 um), carried out with the Spitzer Space Telescope. This rare class of sources, dubbed Infrared-Faint Radio Sources, or IFRS, is inconsistent with current galaxy evolution models. VLBI observations are an essential way to obtain further clues on what these objects are and why they are hidden from infrared observations: we will map their structure to test whether they resemble core-jet or double-lobed morphologies, and we will measure the flux densities on long baselines, to determine their compactness. Previous snapshot-style LBA observations of two other IFRS yielded no detections, hence we propose to use disk-based recording with 512 Mbps where possible, for highest sensitivity. With the observations proposed here, we will increase the number of VLBI-observed IFRS from two to five, soon allowing us to draw general conclusions about this intriguing new class of objects.

76 FR 56724 - Proposed Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-14

.../town/county Source of flooding Location ** ground [caret] Elevation in meters (MSL) Existing Modified... Datum. Depth in feet above ground. [caret] Mean Sea Level, rounded to the nearest 0.1 meter. ** BFEs to... upstream of Cradduck Road None +876 Oklahoma Unincorporated Areas of Town Branch Approximately 400 feet...

33 CFR 203.62 - Drought assistance.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 3 2011-07-01 2011-07-01 false Drought assistance. 203.62... Supplies: Contaminated Water Sources and Drought Assistance § 203.62 Drought assistance. (a) Authority. The... political subdivisions, within areas determined to be drought-distressed. (b) General policy. (1) It is a...

33 CFR 203.62 - Drought assistance.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 33 Navigation and Navigable Waters 3 2013-07-01 2013-07-01 false Drought assistance. 203.62... Supplies: Contaminated Water Sources and Drought Assistance § 203.62 Drought assistance. (a) Authority. The... political subdivisions, within areas determined to be drought-distressed. (b) General policy. (1) It is a...

33 CFR 203.62 - Drought assistance.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 33 Navigation and Navigable Waters 3 2012-07-01 2012-07-01 false Drought assistance. 203.62... Supplies: Contaminated Water Sources and Drought Assistance § 203.62 Drought assistance. (a) Authority. The... political subdivisions, within areas determined to be drought-distressed. (b) General policy. (1) It is a...

33 CFR 203.62 - Drought assistance.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 33 Navigation and Navigable Waters 3 2014-07-01 2014-07-01 false Drought assistance. 203.62... Supplies: Contaminated Water Sources and Drought Assistance § 203.62 Drought assistance. (a) Authority. The... political subdivisions, within areas determined to be drought-distressed. (b) General policy. (1) It is a...

7 CFR 1.411 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Sourcing area applicant means a person who submits a sourcing area application pursuant to these rules, or a person who sourcing area is subject to formal review pursuant to 36 CFR 223.191(e). (b) Decision... Sourcing Area Applications and Formal Review of Sourcing Areas Pursuant to the Forest Resources...

Petroleum hydrocarbons in a water-sediment system from Yellow River estuary and adjacent coastal area, China: Distribution pattern, risk assessment and sources.

PubMed

Wang, Min; Wang, Chuanyuan; Li, Yuanwei

2017-09-15

Aliphatic hydrocarbons (AHs), biomarker and polycyclic aromatic hydrocarbons (PAHs) concentrations of surface water and sediment samples collected from Yellow River Estuary and adjacent coastal area in China were measured to determine their spatial distributions, analyze their sources and evaluate the ecological risk of PAHs in the water-sediment system. The spatial distributions of n-alkane in sediments are mainly controlled by the mixing inputs of terrigenous and marine components. In comparison with AHs, the total concentrations of Σ16PAHs in surface sediments from a transect of the offshore area were noticeably higher than that of the riverine and estuary areas. Additionally, the AHs and total PAHs concentrations all indicated an overall pattern of a seaward decrease. The PAHs concentrations during the dry season (mainly in the form of dissolved phase) were higher than that of PAHs (mainly dissolved phase and particulate phase form) in the flooding season. In comparison with global concentration levels of PAHs, the level of PAHs in suspended particulate matter and sediments from the Yellow River Estuary was lower than those from other countries, while the concentration of PAHs in the dissolved phase were in the middle range. Petroleum contamination, mainly from oil exploration and discharge of pollutants from rivers, was the main source of n-alkanes. The PAHs in the river were mostly of petrogenic origin, while those in the estuarial and marine areas originated mainly from pyrogenic sources. The results of the toxicology assessment suggested that the PAHs in sediments from Yellow River Estuary and adjacent coastal area exhibited a low potential eco-toxicological contamination level. Copyright © 2017 Elsevier Ltd. All rights reserved.

Particle Size, Surface Area, and Amorphous Content as Predictors of Solubility and Bioavailability for Five Commercial Sources of Ferric Orthophosphate in Ready-To-Eat Cereal.

PubMed

Dickmann, Robin S; Strasburg, Gale M; Romsos, Dale R; Wilson, Lori A; Lai, Grace H; Huang, Hsimin

2016-03-01

Ferric orthophosphate (FePO₄) has had limited use as an iron fortificant in ready-to-eat (RTE) cereal because of its variable bioavailability, the mechanism of which is poorly understood. Even though FePO₄ has desirable sensory properties as compared to other affordable iron fortificants, few published studies have well-characterized its physicochemical properties. Semi-crystalline materials such as FePO₄ have varying degrees of molecular disorder, referred to as amorphous content, which is hypothesized to be an important factor in bioavailability. The objective of this study was to systematically measure the physicochemical factors of particle size, surface area, amorphous content, and solubility underlying the variation in FePO₄ bioavailability. Five commercial FePO₄ sources and ferrous sulfate were added to individual batches of RTE cereal. The relative bioavailability value (RBV) of each iron source, determined using the AOAC Rat Hemoglobin Repletion Bioassay, ranged from 51% to 99% (p < 0.05), which is higher than typically reported. Solubility in dilute HCl accurately predicted RBV (R² = 0.93, p = 0.008). Amorphous content measured by Dynamic Vapor Sorption ranged from 1.7% to 23.8% and was a better determinant of solubility (R² = 0.91; p = 0.0002) than surface area (R² = 0.83; p = 0.002) and median particle size (R² = 0.59; p = 0.12). The results indicate that while solubility of FePO₄ is highly predictive of RBV, solubility, in turn, is strongly linked to amorphous content and surface area. This information may prove useful for the production of FePO₄ with the desired RBV.

Particle Size, Surface Area, and Amorphous Content as Predictors of Solubility and Bioavailability for Five Commercial Sources of Ferric Orthophosphate in Ready-To-Eat Cereal

PubMed Central

Dickmann, Robin S.; Strasburg, Gale M.; Romsos, Dale R.; Wilson, Lori A.; Lai, Grace H.; Huang, Hsimin

2016-01-01

Ferric orthophosphate (FePO4) has had limited use as an iron fortificant in ready-to-eat (RTE) cereal because of its variable bioavailability, the mechanism of which is poorly understood. Even though FePO4 has desirable sensory properties as compared to other affordable iron fortificants, few published studies have well-characterized its physicochemical properties. Semi-crystalline materials such as FePO4 have varying degrees of molecular disorder, referred to as amorphous content, which is hypothesized to be an important factor in bioavailability. The objective of this study was to systematically measure the physicochemical factors of particle size, surface area, amorphous content, and solubility underlying the variation in FePO4 bioavailability. Five commercial FePO4 sources and ferrous sulfate were added to individual batches of RTE cereal. The relative bioavailability value (RBV) of each iron source, determined using the AOAC Rat Hemoglobin Repletion Bioassay, ranged from 51% to 99% (p < 0.05), which is higher than typically reported. Solubility in dilute HCl accurately predicted RBV (R2 = 0.93, p = 0.008). Amorphous content measured by Dynamic Vapor Sorption ranged from 1.7% to 23.8% and was a better determinant of solubility (R2 = 0.91; p = 0.0002) than surface area (R2 = 0.83; p = 0.002) and median particle size (R2 = 0.59; p = 0.12). The results indicate that while solubility of FePO4 is highly predictive of RBV, solubility, in turn, is strongly linked to amorphous content and surface area. This information may prove useful for the production of FePO4 with the desired RBV. PMID:26938556

The Herschel-ATLAS data release 1 - I. Maps, catalogues and number counts

NASA Astrophysics Data System (ADS)

Valiante, E.; Smith, M. W. L.; Eales, S.; Maddox, S. J.; Ibar, E.; Hopwood, R.; Dunne, L.; Cigan, P. J.; Dye, S.; Pascale, E.; Rigby, E. E.; Bourne, N.; Furlanetto, C.; Ivison, R. J.

2016-11-01

We present the first major data release of the largest single key-project in area carried out in open time with the Herschel Space Observatory. The Herschel Astrophysical Terahertz Large Area Survey (H-ATLAS) is a survey of 600 deg2 in five photometric bands - 100, 160, 250, 350 and 500 μm - with the Photoconductor Array Camera and Spectrometer and Spectral and Photometric Imaging Receiver (SPIRE) cameras. In this paper and the companion Paper II, we present the survey of three fields on the celestial equator, covering a total area of 161.6 deg2 and previously observed in the Galaxy and Mass Assembly (GAMA) spectroscopic survey. This paper describes the Herschel images and catalogues of the sources detected on the SPIRE 250 μm images. The 1σ noise for source detection, including both confusion and instrumental noise, is 7.4, 9.4 and 10.2 mJy at 250, 350 and 500 μm. Our catalogue includes 120 230 sources in total, with 113 995, 46 209 and 11 011 sources detected at >4σ at 250, 350 and 500 μm. The catalogue contains detections at >3σ at 100 and 160 μm for 4650 and 5685 sources, and the typical noise at these wavelengths is 44 and 49 mJy. We include estimates of the completeness of the survey and of the effects of flux bias and also describe a novel method for determining the true source counts. The H-ATLAS source counts are very similar to the source counts from the deeper HerMES survey at 250 and 350 μm, with a small difference at 500 μm. Appendix A provides a quick start in using the released data sets, including instructions and cautions on how to use them.

Focal mechanism determination for induced seismicity using the neighbourhood algorithm

NASA Astrophysics Data System (ADS)

Tan, Yuyang; Zhang, Haijiang; Li, Junlun; Yin, Chen; Wu, Furong

2018-06-01

Induced seismicity is widely detected during hydraulic fracture stimulation. To better understand the fracturing process, a thorough knowledge of the source mechanism is required. In this study, we develop a new method to determine the focal mechanism for induced seismicity. Three misfit functions are used in our method to measure the differences between observed and modeled data from different aspects, including the waveform, P wave polarity and S/P amplitude ratio. We minimize these misfit functions simultaneously using the neighbourhood algorithm. Through synthetic data tests, we show the ability of our method to yield reliable focal mechanism solutions and study the effect of velocity inaccuracy and location error on the solutions. To mitigate the impact of the uncertainties, we develop a joint inversion method to find the optimal source depth and focal mechanism simultaneously. Using the proposed method, we determine the focal mechanisms of 40 stimulation induced seismic events in an oil/gas field in Oman. By investigating the results, we find that the reactivation of pre-existing faults is the main cause of the induced seismicity in the monitored area. Other observations obtained from the focal mechanism solutions are also consistent with earlier studies in the same area.

Improvement of health risk factors after reduction of VOC concentrations in industrial and urban areas.

PubMed

Lerner, Jorge Esteban Colman; Kohajda, Tibor; Aguilar, Myriam Elisabeth; Massolo, Laura Andrea; Sánchez, Erica Yanina; Porta, Atilio Andrés; Opitz, Philipp; Wichmann, Gunnar; Herbarth, Olf; Mueller, Andrea

2014-01-01

After reductions of fugitive and diffuse emissions by an industrial complex, a follow-up study was performed to determine the time variability of volatile organic compounds (VOCs) and the lifetime cancer risk (LCR). Passive samplers (3 M monitors) were placed outdoors (n = 179) and indoors (n = 75) in industrial, urban, and control areas for 4 weeks. Twenty-five compounds including n-alkanes, cycloalkanes, aromatics, chlorinated hydrocarbons, and terpenes were determined by GC/MS. The results show a significant decrease of all VOCs, especially in the industrial area and to a lesser extent in the urban area. The median outdoor concentration of benzene in the industrial area declined compared to the former study, around 85% and about 50% in the urban area, which in the past was strongly influenced by industrial emissions. Other carcinogenic compounds like styrene and tetrachloroethylene were reduced to approximately 60%. VOC concentrations in control areas remained nearly unchanged. According to the determined BTEX ratios and interspecies correlations, in contrast to the previous study, traffic was identified as the main emission source in the urban and control areas and showed an increased influence in the industrial area. The LCR, calculated for benzene, styrene, and tetrachloroethylene, shows a decrease of one order of magnitude in accordance to the decreased total VOC concentrations and is now acceptable according to values proposed by the World Health Organization.

Spatial variability in airborne bacterial communities across land-use types and their relationship to the bacterial communities of potential source environments

PubMed Central

Bowers, Robert M; McLetchie, Shawna; Knight, Rob; Fierer, Noah

2011-01-01

Although bacteria are ubiquitous in the near-surface atmosphere and they can have important effects on human health, airborne bacteria have received relatively little attention and their spatial dynamics remain poorly understood. Owing to differences in meteorological conditions and the potential sources of airborne bacteria, we would expect the atmosphere over different land-use types to harbor distinct bacterial communities. To test this hypothesis, we sampled the near-surface atmosphere above three distinct land-use types (agricultural fields, suburban areas and forests) across northern Colorado, USA, sampling five sites per land-use type. Microbial abundances were stable across land-use types, with ∼105–106 bacterial cells per m3 of air, but the concentrations of biological ice nuclei, determined using a droplet freezing assay, were on average two and eight times higher in samples from agricultural areas than in the other two land-use types. Likewise, the composition of the airborne bacterial communities, assessed via bar-coded pyrosequencing, was significantly related to land-use type and these differences were likely driven by shifts in the sources of bacteria to the atmosphere across the land-uses, not local meteorological conditions. A meta-analysis of previously published data shows that atmospheric bacterial communities differ from those in potential source environments (leaf surfaces and soils), and we demonstrate that we may be able to use this information to determine the relative inputs of bacteria from these source environments to the atmosphere. This work furthers our understanding of bacterial diversity in the atmosphere, the terrestrial controls on this diversity and potential approaches for source tracking of airborne bacteria. PMID:21048802

A high resolution gas scintillation proportional counter for studying low energy cosmic X-ray sources

NASA Technical Reports Server (NTRS)

Hamilton, T. T.; Hailey, C. J.; Ku, W. H.-M.; Novick, R.

1980-01-01

In recent years much effort has been devoted to the development of large area gas scintillation proportional counters (GSPCs) suitable for use in X-ray astronomy. The paper deals with a low-energy GSPC for use in detecting sub-keV X-rays from cosmic sources. This instrument has a measured energy resolution of 85 eV (FWHM) at 149 eV over a sensitive area of 5 sq cm. The development of imaging capability for this instrument is discussed. Tests are performed on the feasibility of using an arrangement of several phototubes placed adjacent to one another to determine event locations in a large flat counter. A simple prototype has been constructed and successfully operated.

Hydrocarbon prospectivity assessment of the Southern Pattani Trough, Gulf of Thailand

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mountford, N.

The Pattani Trough is an elongate north to south basin in the Gulf of Thailand offshore area that developed from Oligocene times onward. Numerous hydrocarbon discoveries, mainly gas, have been made within the Tertiary stratigraphic section in areas adjacent to the depocenter of the basin, but only dry holes have been drilled on the extreme basin margins and flanking platform areas. The southern Pattani Trough represents a [open quotes]transition zone[close quotes] in terms of potential hydrocarbon prospectivity between the low potential/high exploration risk basin marginal areas, and the high potential/low exploration risk basin marginal area. The development of hydrocarbon accumulationmore » potential within the southern Pattani Trough can be related to a number of major controlling factors. These include structure, which on a regional scale shows a marked influence of tectonic regime on depositional system development, and on a more local scale determines trap development; stratigraphy, which determines reservoir geometry and potential hydrocarbon source rock facies distribution; petrology, which exerts a major control on depth related reservoir quality; overpressure development, which controls local migration pathways for generated hydrocarbons, and locally provides very efficient trap seals; geochemical factors, related to potential source facies distribution, hydrocarbon type; and thermal maturation of the section. The above factors have been combined to define low-, medium-, and high-risk exploration [open quotes]play fairways[close quotes] within the prospectivity transition zone of the southern Pattani Trough.« less

Understanding handpump sustainability: Determinants of rural water source functionality in the Greater Afram Plains region of Ghana†

PubMed Central

Shields, Katherine F.; Chan, Terence U.; Christenson, Elizabeth; Cronk, Ryan D.; Leker, Hannah; Samani, Destina; Apoya, Patrick; Lutz, Alexandra

2015-01-01

Abstract Safe drinking water is critical to human health and development. In rural sub‐Saharan Africa, most improved water sources are boreholes with handpumps; studies suggest that up to one third of these handpumps are nonfunctional at any given time. This work presents findings from a secondary analysis of cross‐sectional data from 1509 water sources in 570 communities in the rural Greater Afram Plains (GAP) region of Ghana; one of the largest studies of its kind. 79.4% of enumerated water sources were functional when visited; in multivariable regressions, functionality depended on source age, management, tariff collection, the number of other sources in the community, and the district. A Bayesian network (BN) model developed using the same data set found strong dependencies of functionality on implementer, pump type, management, and the availability of tools, with synergistic effects from management determinants on functionality, increasing the likelihood of a source being functional from a baseline of 72% to more than 97% with optimal management and available tools. We suggest that functionality may be a dynamic equilibrium between regular breakdowns and repairs, with management a key determinant of repair rate. Management variables may interact synergistically in ways better captured by BN analysis than by logistic regressions. These qualitative findings may prove generalizable beyond the study area, and may offer new approaches to understanding and increasing handpump functionality and safe water access. PMID:27667863

Understanding handpump sustainability: Determinants of rural water source functionality in the Greater Afram Plains region of Ghana

NASA Astrophysics Data System (ADS)

Fisher, Michael B.; Shields, Katherine F.; Chan, Terence U.; Christenson, Elizabeth; Cronk, Ryan D.; Leker, Hannah; Samani, Destina; Apoya, Patrick; Lutz, Alexandra; Bartram, Jamie

2015-10-01

Safe drinking water is critical to human health and development. In rural sub-Saharan Africa, most improved water sources are boreholes with handpumps; studies suggest that up to one third of these handpumps are nonfunctional at any given time. This work presents findings from a secondary analysis of cross-sectional data from 1509 water sources in 570 communities in the rural Greater Afram Plains (GAP) region of Ghana; one of the largest studies of its kind. 79.4% of enumerated water sources were functional when visited; in multivariable regressions, functionality depended on source age, management, tariff collection, the number of other sources in the community, and the district. A Bayesian network (BN) model developed using the same data set found strong dependencies of functionality on implementer, pump type, management, and the availability of tools, with synergistic effects from management determinants on functionality, increasing the likelihood of a source being functional from a baseline of 72% to more than 97% with optimal management and available tools. We suggest that functionality may be a dynamic equilibrium between regular breakdowns and repairs, with management a key determinant of repair rate. Management variables may interact synergistically in ways better captured by BN analysis than by logistic regressions. These qualitative findings may prove generalizable beyond the study area, and may offer new approaches to understanding and increasing handpump functionality and safe water access. This article was corrected on 11 Nov 2015. See the end of the full text for details.

Anthropogenic Enrichment of Heavy Metals in Urban Dust and Possible Corresponding Sources

NASA Astrophysics Data System (ADS)

van Laaten, Neele; Merten, Dirk; Pirrung, Michael

2017-04-01

Atmospheric dust (particulate matter, PM) is regarded as a crucial factor for human health and a major environmental problem in densely populated areas. Due to anthropogenic processes like traffic, waste incineration and industry increased amounts of PM can be detected in those areas. To reduce the amounts detailed knowledge on both the composition of PM and the source contribution in a target area is needed. The latter has, to our knowledge, rarely been regarded in central Europe. Within this study, spider webs from various locations in the city of Jena (Germany), that act as natural trappers of PM, were analyzed for the contents of 27 trace elements using aqua regia digestion followed by ICP-OES and ICP-MS determinations. Aerosol-crust enrichment factors were calculated for selected elements and both a cluster analysis and a factor analysis were executed to identify sources of PM. High values for the enrichment factors clearly show an anthropogenic influence. In addition, the cluster analysis leads to a grouping of the sampling points mainly depending on the kind and volume of traffic at the corresponding locations. Five different possible sources of PM can be found by the factor analysis: Soil erosion (41% of variance), abrasion of rails (16%), tyre and break wear (16%), charcoal combustion (8%) and oil combustion (7%).

A preliminary evaluation of the geohydrology and water quality of the Greenacres Landfill area, Spokane County, Washington

USGS Publications Warehouse

Lum, W. E.; Turney, G.L.; Alvord, R.C.

1986-01-01

The Greenacres Landfill, located about 11 mi east of the city of Spokane, Washington, was used for the disposal of waste from 1951 to 1972. Materials in the landfill include household and industrial waste materials, and various hazardous wastes. In 1983 the landfill was designated by the U.S. EPA as a ' Superfund ' site. The purposes of this investigation were to gather, describe, and interpret all the existing data concerning the hydrology and groundwater quality of the area surrounding the landfill, and to identify any additional data needed to describe the hydrology of the area. The quantity of water flow through the landfill as a result of precipitation on the landfill and in the drainage basin above the landfill probably ranges from 21,000 to 85,000 gal/day. This water movement may be creating a leachate and transporting some of the wastes out of the landfill. The plume would encompass an area where groundwater provides most of the water used for municipal, industrial, irrigation, and domestic purposes. Water quality analyses of water from numerous wells in the area which are open to the Spokane aquifer are available, but well 25/45-16K1 is the only well where groundwater contamination was consistently apparent. This well is only 500 ft from the landfill. Contamination of water in this well was indicated by high concentrations of dissolved mineral constituents and several organic compounds, including trans-dichloroethene (115 to 392 micrograms/L). Available data are insufficient to completely interpret the groundwater flow system near this well and the source of the contamination cannot be determined conclusively. While the existing data are adequate to provide background information, more data are needed to: (1) determine the source of contamination in well 25/45-16K1; (2) determine groundwater flow in the Spokane aquifer near well 25/45-16K1; and (3) determine the extent of contamination in the Spokane aquifer. The degree of the influence of the landfill on the Spokane aquifer cannot be determined with existing data. (Author 's abstract)

Ground-water level fluctuations in Utah, 1936-45: A section in Twenty-fifth biennial report of the State Engineer to the governor of Utah: 1944-1946

USGS Publications Warehouse

Thomas, H.E.

1946-01-01

Ground-water investigations in Utah by the Geological Survey of the U.S. Department of the Interior have been in progress since 1935, in cooperation with the Utah State Engineer. This cooperative work includes (1) determination of the fluctuations of water level in most of the developed ground-water areas in the state, based upon measurements which are tabulated and published annually by the Geological Survey; and (2) detailed investigations of specific ground-water areas to determine source, movement, disposal, quantity and quality of the ground water, and to show the relation of present development to the maximum economic development of which those areas are capable. Such detailed investigations have been completed during the past decade for areas in Iron, Millard, Salt Lake, Tooele, and Weber Counties, and are referred to in discussion subsequently. Similar investigations are now in progress in other areas in Davis, Iron, and Weber Counties.

An operational application of satellite snow cover observations, northwest United States. [using LANDSAT 1

NASA Technical Reports Server (NTRS)

Dillard, J. P.

1975-01-01

LANDSAT-1 imagery showing extent of snow cover was collected and is examined for the 1973 and 1974 snowmelt seasons for three Columbia River Basins. Snowlines were mapped and the aerial snow cover was determined using satellite data. Satellite snow mapping products were compared products from conventional information sources (computer programming and aerial photography was used). Available satellite data were successfully analyzed by radiance thresholding to determine snowlines and the attendant snow-covered area. Basin outline masks, contour elevation masks, and grid overlays were utilized as satellite data interpretation aids. Verification of the LANDSAT-1 data was generally good although there were exceptions. A major problem was lack of adequate cloud-free satellite imagery of high resolution and determining snowlines in forested areas.

Active System for Electromagnetic Perturbation Monitoring in Vehicles

NASA Astrophysics Data System (ADS)

Matoi, Adrian Marian; Helerea, Elena

Nowadays electromagnetic environment is rapidly expanding in frequency domain and wireless services extend in terms of covered area. European electromagnetic compatibility regulations refer to limit values regarding emissions, as well as procedures for determining susceptibility of the vehicle. Approval procedure for a series of cars is based on determining emissions/immunity level for a few vehicles picked randomly from the entire series, supposing that entire vehicle series is compliant. During immunity assessment, the vehicle is not subjected to real perturbation sources, but exposed to electric/magnetic fields generated by laboratory equipment. Since current approach takes into account only partially real situation regarding perturbation sources, this paper proposes an active system for determining electromagnetic parameters of vehicle's environment, that implements a logical diagram for measurement, satisfying the imposed requirements. This new and original solution is useful for EMC assessment of hybrid and electrical vehicles.

Bibliography on aircraft fire hazards and safety. Volume 1: Hazards. Part 1: Key numbers 1 to 817

NASA Technical Reports Server (NTRS)

Pelouch, J. J., Jr. (Compiler); Hacker, P. T. (Compiler)

1974-01-01

Ignition temperatures of n-hexane, n-octane, n-decane, JP-6 jet fuel, and aircraft engine oil MIL-7-7808 (0-60-18) were determined in air using heated Pyrex cylinders and Nichrome wires, rods, or tubes. Ignition temperature varied little with fuel-air ratio, but increased as the size of the heat source was decreased. Expressions are given which define the variation of the hot surface ignition temperatures of these combustibles with the radius and the surface area of the heat source. The expressions are applicable to stagnant or low velocity flow conditions (less than 0.2 in./sec.). In addition, the hot gas ignition temperatures of the combustible vapor-air mixtures were determined with jets of hot air. These ignition temperatures also varied little with fuel-air ratio and increased as the diameter of the heat sources was decreased.

Proximity of Private Domestic Wells to Underground Storage Tanks in Oklahoma

EPA Science Inventory

For protecting drinking water supplies, the locations of areas with reliance on private domestic wells (hereafter referred to as “wells”) and their relationship to contaminant sources need to be determined. A key resource in the U.S. was the 1990 Census where the sour...

MERCURY CONCENTRATIONS IN SEDIMENT, WATER AND BIOTA COLLECTED FROM NEAR-COASTAL AREAS IMPACTED BY COMMON ESTUARINE STRESSORS

EPA Science Inventory

Mercury concentrations in non-commercial organisms indigenous to the Gulf of Mexico are not well characterized particularly when compared to potential sources. In response to this need, mercury levels were determined in sediment, water and various biota in reference and non-refer...

78 FR 5738 - Final Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-28

... in feet (NGVD) + Elevation in feet (NAVD) Depth in feet State City/town/county Source of flooding... feet upstream of I-15 +3433 Areas of (westbound). Cascade County. Approximately 1.2 miles upstream of I... feet above ground. [caret] Mean Sea Level, rounded to the nearest 0.1 meter. ADDRESSES Unincorporated...

Modeling Soak-Time Distribution of Trips for Mobile Source Emissions Forecasting: Techniques and Applications

DOT National Transportation Integrated Search

2000-08-01

The soak-time of vehicle trip starts is defined as the duration of time in which the vehicle's engine is not operating and that precedes a successful vehicle start. The temporal distribution of the soak-time in an area is an important determinant of ...

A nitrogen inventory for the Nooksack-Fraser Transboundary Watershed

EPA Science Inventory

The Nooksack-Fraser transboundary area is home to communities with a strong base in farming, fisheries and outdoor recreation. A goal of the Nooksack-Fraser Transboundary Nitrogen (NFT-N) project is to determine the sources and fates of N in the watershed using data on energy us...

77 FR 50668 - Proposed Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-22

... County, Texas, and Incorporated Areas. Specifically, it addresses the flooding sources: Black Fork Creek, Black Fork Creek Tributary BF-1, Black Fork Creek Tributary BF-M-1, Black Fork Creek Tributary D, Black Fork Creek Tributary D-1, Black Fork Creek Tributary D-2, Black Fork Creek Tributary D-3, Butler Creek...

Using electromagnetic induction technology to predict volatile fatty acid, source area differences

USDA-ARS?s Scientific Manuscript database

Subsurface sampling techniques have been adapted to measure manure accumulation on feedlot surface. Objectives of this study were to determine if sensor data could be used to predict differences in volatile fatty acids (VFA) and other volatiles produced on the feedlot surface three days following a...

DIGITAL GEOLOGIC MAP OF SHERMAN QUADRANGLE, NORTH CENTRAL TEXAS (CD-ROM)

EPA Science Inventory

This compact disc contains digital data sets of the surficial geology and geologic faults for the 1:250,000-scale Sherman quadrangle, North Central Texas, and can be used to make geologic maps, and determine approximate areas and locations of various geologic units. The source d...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rozhdestvenskyy, S.

This work iterates on the first demonstration of a solid-state neutron multiplicity counting system developed at Lawrence Livermore National Laboratory by using commercial off-the-shelf detectors. The system was demonstrated to determine the mass of a californium-252 neutron source within 20% error requiring only one-hour measurement time with 20 cm 2 of active detector area.

Source apportionment of atmospheric polycyclic aromatic hydrocarbons (PAHs) in Palm Beach County, Florida.

PubMed

Afshar-Mohajer, Nima; Wilson, Christina; Wu, Chang-Yu; Stormer, James E

2016-04-01

Due to concerns about adverse health effects associated with inhalation of atmospheric polycyclic aromatic hydrocarbons (PAHs), 30 ambient air samples were obtained at an air quality monitoring station in Palm Beach County, Florida, from March 2013 to March 2014. The ambient PAH concentration measurements and fractional emission rates of known sources were incorporated into a chemical mass balance model, CMB8.2, developed by EPA, to apportion contributions of three major PAH sources including preharvest sugarcane burning, mobile vehicles, and wildland fires. Strong association between the number of benzene rings and source contribution was found, and mobile vehicles were identified to be the prevailing source (contribution≥56%) for the observed PAHs concentration with lower molecular weights (four or fewer benzene rings) throughout the year. Preharvest sugarcane burning was the primary contributing source for PAHs with relatively higher molecular weights (five or more benzene rings) during the sugarcane burning season (from October to May of the next year). Source contribution of wildland fires varied among PAH compounds but was consistently lower than for sugarcane burning during the sugarcane harvest season. Determining the major sources responsible for ground-level PAHs serves as a tool to improving management strategies for PAH emitting sources and a step toward better protection of the health of residents in terms of exposure to PAHs. The results obtain insight into temporal dominance of PAH polluting sources for those residential areas located near sugarcane burning facilities and have implications beyond Palm Beach County, in areas with high concerns of PAHs and their linked sources. Source apportionment of atmospheric polycyclic hydrocarbons (PAHs) in Palm Beach County, Florida, meant to estimate contributions of major sources in PAH concentrations measured at Belle Glade City of Palm Beach County. Number of benzene rings was found to be the key parameter in determining the source with the prevailing contribution. Mobile vehicle sources showed a higher contribution for species with four or fewer benzene rings, whereas sugarcane burning contributed more for species with five or more benzene rings. Results from this study encourage more control for sugarcane burns and help to better manage authorization of the sugarcane burning incidents and more restrictive transportation plans to limit PAH emissions from mobile vehicles.

Estimating Phosphorus Loss at the Whole-Farm Scale with User-Friendly Models

NASA Astrophysics Data System (ADS)

Vadas, P.; Powell, M.; Brink, G.; Busch, D.; Good, L.

2014-12-01

Phosphorus (P) loss from agricultural fields and delivery to surface waters persists as a water quality impairment issue. For dairy farms, P can be lost from cropland, pastures, barnyards, and open-air cattle lots; and all these sources must be evaluated to determine which ones are a priority for P loss remediation. We used interview surveys to document land use, cattle herd characteristics, and manure management for four grazing-based dairy farms in Wisconsin, USA. We then used the APLE and Snap-Plus models to estimate annual P loss from all areas on these farms and determine their relative contribution to whole-farm P loss. At the whole-farm level, average annual P loss (kg ha-1) from grazing-based dairy farms was low (0.6 to 1.8 kg ha-1), generally because a significant portion of land was in permanently vegetated pastures or hay and had low erosion. However, there were areas on the farms that represented sources of significant P loss. For cropland, the greatest P loss was from areas with exposed soil, typically for corn production, and especially on steeper sloping land. The farm areas with the greatest P loss had concentrated animal housing, including barnyards, and over-wintering and young-stock lots. These areas can represent from about 5% to almost 30% of total farm P loss, depending on lot management and P loss from other land uses. Our project builds on research to show that producer surveys can provide reliable management information to assess whole-farm P loss. It also shows that we can use models like RUSLE2, Snap-Plus, and APLE to rapidly, reliably, and quantitatively estimate P loss in runoff from all areas on a dairy farm and identify areas in greatest need of alternative management to reduce P loss.

Analysis of several heavy metals in wild edible mushrooms from regions of China.

PubMed

Chen, Xin-Hua; Zhou, Hong-Bo; Qiu, Guan-Zhou

2009-08-01

The metal (Cu, Ni, Cd, Hg, As, Pb) contents in wild edible mushrooms collected from three different sites in China were determined by atomic absorption spectrometry and atomic fluorescence spectrometry. All element concentrations were determined on a dry weight basis. A total of 11 species was studied, five being from the urban area and six from rural areas in China. The As content ranged from 0.44 to 1.48 mg/kg. The highest As content was seen in Macrolepiota crustosa from the urban area, and the lowest in Russula virescens from rural areas. A high Ni concentration (1.35 mg/kg) was found in Calvatia craniiformis from the urban area. The lowest Ni level was 0.11 mg/kg, for the species R. virescens and Cantharellus cibarius. The Cu content ranged from 39.0 to 181.5 mg/kg. The highest Cu content was seen in Agaricus silvaticus and the lowest in C. cibarius. The Pb content ranged from 1.9 to 10.8 mg/kg. The highest Pb value was found in C. craniiformis. The Cd content ranged from 0.4 to 91.8 mg/kg. The highest Cd value was found in M. crustosa. The Hg content ranged from 0.28 to 3.92 mg/kg. The highest Hg level was found in Agaricus species. The levels of the heavy metals Cd, Pb, and Hg in the studied mushroom species from urban area can be considered high. The metal-to-metal correlation analysis supported they were the same source of contamination. High automobile traffic was identified as the most likely source of the contamination. Based upon the present safety standards, consumption of those mushrooms that grow in the polluted urban area should be avoided.

Using a Divided Bar Apparatus to Measure Thermal Conductivity of Samples of Odd Sizes and Shapes

NASA Astrophysics Data System (ADS)

Crowell, J. "; Gosnold, W. D.

2012-12-01

Standard procedure for measuring thermal conductivity using a divided bar apparatus requires a sample that has the same surface dimensions as the heat sink/source surface in the divided bar. Heat flow is assumed to be constant throughout the column and thermal conductivity (K) is determined by measuring temperatures (T) across the sample and across standard layers and using the basic relationship Ksample=(Kstandard*(ΔT1+ΔT2)/2)/(ΔTsample). Sometimes samples are not large enough or of correct proportions to match the surface of the heat sink/source, however using the equations presented here the thermal conductivity of these samples can still be measured with a divided bar. Measurements were done on the UND Geothermal Laboratories stationary divided bar apparatus (SDB). This SDB has been designed to mimic many in-situ conditions, with a temperature range of -20C to 150C and a pressure range of 0 to 10,000 psi for samples with parallel surfaces and 0 to 3000 psi for samples with non-parallel surfaces. The heat sink/source surfaces are copper disks and have a surface area of 1,772 mm2 (2.74 in2). Layers of polycarbonate 6 mm thick with the same surface area as the copper disks are located in the heat sink and in the heat source as standards. For this study, all samples were prepared from a single piece of 4 inch limestone core. Thermal conductivities were measured for each sample as it was cut successively smaller. The above equation was adjusted to include the thicknesses (Th) of the samples and the standards and the surface areas (A) of the heat sink/source and of the sample Ksample=(Kstandard*Astandard*Thsample*(ΔT1+ΔT3))/(ΔTsample*Asample*2*Thstandard). Measuring the thermal conductivity of samples of multiple sizes, shapes, and thicknesses gave consistent values for samples with surfaces as small as 50% of the heat sink/source surface, regardless of the shape of the sample. Measuring samples with surfaces smaller than 50% of the heat sink/source surface resulted in thermal conductivity values which were too high. The cause of the error with the smaller samples is being examined as is the relationship between the amount of error in the thermal conductivity and the difference in surface areas. As more measurements are made an equation to mathematically correct for the error is being developed on in case a way to physically correct the problem cannot be determined.

Characterization of atmospheric black carbon and co-pollutants in urban and rural areas of Spain

NASA Astrophysics Data System (ADS)

Becerril-Valle, M.; Coz, E.; Prévôt, A. S. H.; Močnik, G.; Pandis, S. N.; Sánchez de la Campa, A. M.; Alastuey, A.; Díaz, E.; Pérez, R. M.; Artíñano, B.

2017-11-01

A one-year black carbon (BC) experimental study was performed at three different locations (urban traffic, urban background, rural) in Spain with different equivalent BC (eBC) source characteristics by means of multi-wavelength Aethalometers. The Aethalometer model was used for the source apportionment study, based on the difference in absorption spectral dependence of emissions from biomass burning (bb) and fossil fuel (ff) combustion. Most studies use a single bb and ff absorption Ångström exponent (AAE) pair (AAEbb and AAEff), however in this work we use a range of AAE values associated with fossil fuel and biomass burning based on the available measurements, which represents more properly all conditions. A sensitivity analysis of the source specific AAE was carried out to determine the most appropriate AAE values, being site dependent and seasonally variable. Here we present a methodology for the determination of the ranges of AAEbb and AAEff by evaluating the correlations between the source apportionment of eBC using the Aethalometer model with four biomass burning tracers measured at the rural site. The best combination was AAEbb = [1.63-1.74] and AAEff = [0.97-1.12]. Mean eBC values (±SD) obtained during the period of study were 3.70 ± 3.73 μg m-3 at the traffic urban site, 2.33 ± 2.96 μg m-3 at the urban background location, and 2.61 ± 5.04 μg m-3 in the rural area. High contributions of eBC to the PM10 mass were found (values up to 21% in winter), but with high eBC/PM10 variability. The hourly mean eBCff and eBCbb concentrations varied from 0 to 51 μg m-3 and from 0 to 50 μg m-3 at the three sites, respectively, exhibiting distinct seasonal and daily patterns. The fossil fuel combustion was the dominant eBC source at the urban sites, while biomass burning dominated during the cold season (88% of eBCbb) in the rural area. Daily PM2.5 and PM10 samples were collected using high-volume air samplers and analyzed for OC and EC. Analysis of biomass burning tracers and organic (OC) and elemental (EC) carbon in the rural area indicate that biomass combustion is the main source, while OC and EC indicate a lower influence of this source at the urban site.

Integrated Environmental Risk Assessment and Whole-Process Management System in Chemical Industry Parks

PubMed Central

Shao, Chaofeng; Yang, Juan; Tian, Xiaogang; Ju, Meiting; Huang, Lei

2013-01-01

Chemical industry parks in China are considered high-risk areas because they present numerous risks that can damage the environment, such as pollution incidents. In order to identify the environmental risks and the principal risk factors in these areas, we have developed a simple physical model of a regional environmental risk field (ERF) using existing dispersal patterns and migration models. The regional ERF zoning was also conducted and a reference value for diagnostic methods was developed to determine risk-acceptable, risk-warning, and risk-mitigation zones, which can provide a risk source layout for chemical industry parks. In accordance with the environmental risk control requirements, this study focused on the three stages of control and management of environmental risk and established an environmental risk management system including risk source identification and assessment, environmental safety planning, early risk warning, emergency management, assessment of environmental effects, and environmental remediation of pollution accidents. By using this model, the environmental risks in Tianjin Binhai New Area, the largest chemical industry park in China, were assessed and the environmental risk zoning map was drawn, which suggested the existence of many unacceptable environmental risks in this area. Thus, relevant suggestions have been proposed from the perspective of the adjustment of risk source layout, intensified management of environmental risk control and so on. PMID:23603866

Integrated environmental risk assessment and whole-process management system in chemical industry parks.

PubMed

Shao, Chaofeng; Yang, Juan; Tian, Xiaogang; Ju, Meiting; Huang, Lei

2013-04-19

Chemical industry parks in China are considered high-risk areas because they present numerous risks that can damage the environment, such as pollution incidents. In order to identify the environmental risks and the principal risk factors in these areas, we have developed a simple physical model of a regional environmental risk field (ERF) using existing dispersal patterns and migration models. The regional ERF zoning was also conducted and a reference value for diagnostic methods was developed to determine risk-acceptable, risk-warning, and risk-mitigation zones, which can provide a risk source layout for chemical industry parks. In accordance with the environmental risk control requirements, this study focused on the three stages of control and management of environmental risk and established an environmental risk management system including risk source identification and assessment, environmental safety planning, early risk warning, emergency management, assessment of environmental effects, and environmental remediation of pollution accidents. By using this model, the environmental risks in Tianjin Binhai New Area, the largest chemical industry park in China, were assessed and the environmental risk zoning map was drawn, which suggested the existence of many unacceptable environmental risks in this area. Thus, relevant suggestions have been proposed from the perspective of the adjustment of risk source layout, intensified management of environmental risk control and so on.

Hydrodynamic simulation and particle-tracking techniques for identification of source areas to public-water intakes on the St. Clair-Detroit river waterway in the Great Lakes Basin

USGS Publications Warehouse

Holtschlag, David J.; Koschik, John A.

2004-01-01

Source areas to public water intakes on the St. Clair-Detroit River Waterway were identified by use of hydrodynamic simulation and particle-tracking analyses to help protect public supplies from contaminant spills and discharges. This report describes techniques used to identify these areas and illustrates typical results using selected points on St. Clair River and Lake St. Clair. Parameterization of an existing two-dimensional hydrodynamic model (RMA2) of the St. Clair-Detroit River Waterway was enhanced to improve estimation of local flow velocities. Improvements in simulation accuracy were achieved by computing channel roughness coefficients as a function of flow depth, and determining eddy viscosity coefficients on the basis of velocity data. The enhanced parameterization was combined with refinements in the model mesh near 13 public water intakes on the St. Clair-Detroit River Waterway to improve the resolution of flow velocities while maintaining consistency with flow and water-level data. Scenarios representing a range of likely flow and wind conditions were developed for hydrodynamic simulation. Particle-tracking analyses combined advective movements described by hydrodynamic scenarios with random components associated with sub-grid-scale movement and turbulent mixing to identify source areas to public water intakes.

Hydrological and hydraulic models for determination of flood-prone and flood inundation areas

NASA Astrophysics Data System (ADS)

Aksoy, Hafzullah; Sadan Ozgur Kirca, Veysel; Burgan, Halil Ibrahim; Kellecioglu, Dorukhan

2016-05-01

Geographic Information Systems (GIS) are widely used in most studies on water resources. Especially, when the topography and geomorphology of study area are considered, GIS can ease the work load. Detailed data should be used in this kind of studies. Because of, either the complication of the models or the requirement of highly detailed data, model outputs can be obtained fast only with a good optimization. The aim in this study, firstly, is to determine flood-prone areas in a watershed by using a hydrological model considering two wetness indexes; the topographical wetness index, and the SAGA (System for Automated Geoscientific Analyses) wetness index. The wetness indexes were obtained in the Quantum GIS (QGIS) software by using the Digital Elevation Model of the study area. Flood-prone areas are determined by considering the wetness index maps of the watershed. As the second stage of this study, a hydraulic model, HEC-RAS, was executed to determine flood inundation areas under different return period-flood events. River network cross-sections required for this study were derived from highly detailed digital elevation models by QGIS. Also river hydraulic parameters were used in the hydraulic model. Modelling technology used in this study is made of freely available open source softwares. Based on case studies performed on watersheds in Turkey, it is concluded that results of such studies can be used for taking precaution measures against life and monetary losses due to floods in urban areas particularly.

Chemical mass balance source apportionment of TSP in a lignite-burning area of Western Macedonia, Greece

NASA Astrophysics Data System (ADS)

Samara, Constantini

Total suspended particle mass concentrations (TSP) were determined in the Kozani-Ptolemais-Florina basin (western Macedonia, Greece), an area with intensive lignite burning for power generation. The study was conducted over a 1-year period (November 2000-November 2001) at 10 receptor sites located at variable distances from the power plants. Ambient TSP samples were analyzed for 27 major, minor and trace elements. Particulate emissions were also collected from a variety of sources including fly ash, lignite dust, automobile traffic, domestic heating, and open-air burning of agricultural biomass and refuse, and analyzed for the same chemical components. Ambient and source chemical profiles were used for source identification and apportionment of TSP by employing a chemical mass balance (CMB) receptor model. Diesel burning in vehicular traffic and in the power plants for generator start up was found to be the major contributor to ambient TSP levels at all 10 sites. Other sources with significant contributions were domestic coal burning, vegetative burning (wood combustion and agricultural burns) and refuse open-air burning. Fly ash escaping the electrostatic precipitators of the power plants was a minor contributor to ambient TSP.

MODEL-FREE MULTI-PROBE LENSING RECONSTRUCTION OF CLUSTER MASS PROFILES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Umetsu, Keiichi

2013-05-20

Lens magnification by galaxy clusters induces characteristic spatial variations in the number counts of background sources, amplifying their observed fluxes and expanding the area of sky, the net effect of which, known as magnification bias, depends on the intrinsic faint-end slope of the source luminosity function. The bias is strongly negative for red galaxies, dominated by the geometric area distortion, whereas it is mildly positive for blue galaxies, enhancing the blue counts toward the cluster center. We generalize the Bayesian approach of Umetsu et al. for reconstructing projected cluster mass profiles, by incorporating multiple populations of background sources for magnification-biasmore » measurements and combining them with complementary lens-distortion measurements, effectively breaking the mass-sheet degeneracy and improving the statistical precision of cluster mass measurements. The approach can be further extended to include strong-lensing projected mass estimates, thus allowing for non-parametric absolute mass determinations in both the weak and strong regimes. We apply this method to our recent CLASH lensing measurements of MACS J1206.2-0847, and demonstrate how combining multi-probe lensing constraints can improve the reconstruction of cluster mass profiles. This method will also be useful for a stacked lensing analysis, combining all lensing-related effects in the cluster regime, for a definitive determination of the averaged mass profile.« less

Origin of soluble chemical species in bulk precipitation collected in Tokyo, Japan: Statistical evaluation of source materials

NASA Astrophysics Data System (ADS)

Tsurumi, Makoto; Takahashi, Akira; Ichikuni, Masami

An iterative least-squares method with a receptor model was applied to the analytical data of the precipitation samples collected at 23 points in the suburban area of Tokyo, and the number and composition of the source materials were determined. Thirty-nine monthly bulk precipitation samples were collected in the spring and summer of 1987 from the hilly and mountainous area of Tokyo and analyzed for Na +, K +, NH 4+, Mg 2+, Ca 2+, F -, Cl -, Br -, NO 3- and SO 42- by atomic absorption spectrometry and ion chromatography. The pH of the samples was also measured. A multivariate ion balance approach (Tsurumi, 1982, Anal. Chim. Acta138, 177-182) showed that the solutes in the precipitation were derived from just three major sources; sea salt, acid substance (a mixture of 53% HNO 3, 39% H 2SO 4 and 8% HCl in equivalent) and CaSO 4. The contributions of each source to the precipitation were calculated for every sampling site. Variations of the contributions with the distance from the coast were also discussed.

Urban rivers as conveyors of hydrocarbons to sediments of estuarine areas: source characterization, flow rates and mass accumulation.

PubMed

Mauad, Cristiane R; Wagener, Angela de L R; Massone, Carlos G; Aniceto, Mayara da S; Lazzari, Letícia; Carreira, Renato S; Farias, Cássia de O

2015-02-15

Aliphatic (n-C12-n-C40, unresolved complex mixture, resolved peaks) and aromatic hydrocarbons (46 PAH) were investigated in suspended particulate matter (SPM) sampled over eleven months in six of the major rivers and two channels of the Guanabara Bay Basin. PAH flow rates of the most contaminated rivers, the contribution to the PAH sediment load of the receiving bay, and the main sources of hydrocarbons were determined. PAH (38) ranged from 28 ng L(-1) to 11,514 ng L(-1). Hydrocarbon typology and statistical evaluation demonstrated contribution of distinct sources in different regions and allowed quantification of these contributions. Total flow rate for the five major rivers amounts to 3 t year(-1) and responds for 30% of the total PAH annual input into the northern area of the Guanabara Bay. For the first time PAH mass deposited in the bay sediments has been estimated and shall serve as base for decision making and source abatement. Copyright © 2014 Elsevier B.V. All rights reserved.

Effects of waste-disposal practices on ground-water quality at five poultry (broiler) farms in north-central Florida, 1992-93

USGS Publications Warehouse

Hatzell, H.H.

1995-01-01

Waste-disposal areas such as chicken-house floors, litter stockpiles, fields that receive applications of litter, and dead-chicken pits are potential sources of nitrates and other chemical constituents in downward-percolating recharge water. Broiler- farms in north-central Florida are concentrated in a region where the Upper Floridan aquifer is unconfined and susceptible to contamination. Eighteen monitoring wells installed at five sites were sampled quarterly from March 1992 through January 1993. Increases in median concentrations of constituents relative to an upgradient well were used to determine the source of the nitrate at two sites. At these sites, increases in the median concentrations of nitrate as nitrogen in ground water in the vicinity of waste-disposal areas at these sites were: 5.4 mg/L for one chicken house; 9.0 mg/L for a second chicken house; 2.0 mg/L for a fallow field that received an application of litter; and, 2.0 mg/L for a dead-chicken pit. At the three remaining sites where the direction of local ground-water flow could not be ascertained, the sources of concentrations of nitrate and other constituents could not be determined. However, median nitrate concentrations in the vicinity of waste-disposal areas at these sites were: 45.5 mg/L for a set of two chicken houses; 3.0 mg/L for a stockpile area; and 2.1 mg/L for a hayfield that received an application of litter. The nitrate concentration in ground water in the vicinity of a field that had previously received heavy applications of litter increased from 3.0 mg/L to 105 mg/L approximately 4 months after receiving an application of commercial fertilizer. Increases in concentrations of organic nitrogen in ground water in the vicinity of waste-disposal areas may be related to the decomposition of litter and subsequent movement with downward percolating recharge water.(USGS)

Population dynamics of rice planthoppers, Nilaparvata lugens and Sogatella furcifera (Hemiptera, Delphacidae) in Central Vietnam and its effects on their spring migration to China.

PubMed

Hu, G; Lu, M-H; Tuan, H A; Liu, W-C; Xie, M-C; McInerney, C E; Zhai, B-P

2017-06-01

Rice planthopper (RPH) populations of Nilaparvata lugens and Sogatella furcifera periodically have erupted across Asia. Predicting RPH population dynamics and identifying their source areas are crucial for the management of these migratory pests in China, but the origins of the migrants to temperate and subtropical regions in China remains unclear. In particular, their early migration to China in March and April have not yet been explored due to a lack of research data available from potential source areas, Central Vietnam and Laos. In this study, we examined the population dynamics and migratory paths of N. lugens and S. furcifera in Vietnam and South China in 2012 and 2013. Trajectory modeling showed that in March and April in 2012 and 2013, RPH emigrated from source areas in Central Vietnam where rice was maturing to the Red River Delta and South China. Early migrants originated from Southern Central Vietnam (14-16°N), but later most were from Northern Central Vietnam (16-19°N). Analysis of meteorological and light-trap data from Hepu in April (1977-2013) using generalized linear models showed that immigration increased with precipitation in Southern Central Vietnam in January, but declined with precipitation in Northern Central Vietnam in January. These results determined that the RPH originate from overwintering areas in Central Vietnam, but not from southernmost areas of Vietnam. Winter precipitation, rather than temperature was the most important factor determining the number of RPH migrants. Based on their similar population dynamics and low population densities in Central Vietnam, we further speculated that RPH migrate to track ephemeral food resources whilst simultaneously avoiding predators. Migrations do not seem to be initiated by interspecific competition, overcrowding or host deterioration. Nevertheless, S. furcifera establishes populations earlier than N. lugens South China, perhaps to compensate for interspecific competition. We provide new information that could assist with forecasting outbreaks and implementing control measures against these migratory pests.

Impact analysis of traffic-related air pollution based on real-time traffic and basic meteorological information.

PubMed

Pan, Long; Yao, Enjian; Yang, Yang

2016-12-01

With the rapid development of urbanization and motorization in China, traffic-related air pollution has become a major component of air pollution which constantly jeopardizes public health. This study proposes an integrated framework for estimating the concentration of traffic-related air pollution with real-time traffic and basic meteorological information and also for further evaluating the impact of traffic-related air pollution. First, based on the vehicle emission factor models sensitive to traffic status, traffic emissions are calculated according to the real-time link-based average traffic speed, traffic volume, and vehicular fleet composition. Then, based on differences in meteorological conditions, traffic pollution sources are divided into line sources and point sources, and the corresponding methods to determine the dynamic affecting areas are also proposed. Subsequently, with basic meteorological data, Gaussian dispersion model and puff integration model are applied respectively to estimate the concentration of traffic-related air pollution. Finally, the proposed estimating framework is applied to calculate the distribution of CO concentration in the main area of Beijing, and the population exposure is also calculated to evaluate the impact of traffic-related air pollution on public health. Results show that there is a certain correlation between traffic indicators (i.e., traffic speed and traffic intensity) of the affecting area and traffic-related CO concentration of the target grid, which indicates the methods to determine the affecting areas are reliable. Furthermore, the reliability of the proposed estimating framework is verified by comparing the predicted and the observed ambient CO concentration. In addition, results also show that the traffic-related CO concentration is higher in morning and evening peak hours, and has a heavier impact on public health within the Fourth Ring Road of Beijing due to higher population density and higher CO concentration under calm wind condition in this area. Copyright © 2016 Elsevier Ltd. All rights reserved.

Is drinking water from 'improved sources' really safe? A case study in the Logone valley (Chad-Cameroon).

PubMed

Sorlini, S; Palazzini, D; Mbawala, A; Ngassoum, M B; Collivignarelli, M C

2013-12-01

Within a cooperation project coordinated by the Association for Rural Cooperation in Africa and Latin America (ACRA) Foundation, water supplies were sampled across the villages of the Logone valley (Chad-Cameroon) mostly from boreholes, open wells, rivers and lakes as well as from some piped water. Microbiological analyses and sanitary inspections were carried out at each source. The microbiological quality was determined by analysis of indicators of faecal contamination, Escherichia coli, Enterococci and Salmonellae, using the membrane filtration method. Sanitary inspections were done using WHO query forms. The assessment confirmed that there are several parameters of health concern in the studied area; bacteria of faecal origins are the most significant. Furthermore, this study demonstrated that Joint Monitoring Programme (JMP) classification and E. coli measurement are not sufficient to state water safety. In fact, in the studied area, JMP defined 'improved sources' may provide unsafe water depending on their structure and sources without E. coli may have Enterococci and Salmonellae. Sanitary inspections also revealed high health risks for some boreholes. In other cases, sources with low sanitary risk and no E. coli were contaminated by Enterococci and Salmonellae. Better management and protection of the sources, hygiene improvement and domestic water treatment before consumption are possible solutions to reduce health risks in the Logone valley.

Possible sources of nitrate in ground water at swine licensed-managed feeding operations in Oklahoma, 2001

USGS Publications Warehouse

Becker, Mark F.; Peter, Kathy D.; Masoner, Jason

2002-01-01

Samples collected and analyzed by the Oklahoma Department of Agriculture, Food, and Forestry from 1999 to 2001 determined that nitrate exceeded the U.S. Environmental Protection Agency maximum contaminant level for public drinking-water supplies of 10 milligrams per liter as nitrogen in 79 monitoring wells at 35 swine licensed-managed feeding operations (LMFO) in Oklahoma. The LMFOs are located in rural agricultural settings where long-term agriculture has potentially affected the ground-water quality in some areas. Land use prior to the construction of the LMFOs was assessed to evaluate the types of agricultural land use within a 500-meter radius of the sampled wells. Chemical and microbiological techniques were used to determine the possible sources of nitrate in water sampled from 10 wastewater lagoons and 79 wells. Samples were analyzed for dissolved major ions, dissolved trace elements, dissolved nutrients, nitrogen isotope ratios of nitrate and ammonia, wastewater organic compounds, and fecal coliform bacteria. Bacteria ribotyping analysis was done on selected samples to identify possible specific animal sources. A decision process was developed to identify the possible sources of nitrate. First, nitrogen isotope ratios were used to define sources as animal, mixed animal and fertilizer, or fertilizer. Second, wastewater organic compound detections, nitrogen-isotope ratios, fecal coliform bacteria detections, and ribotyping were used to refine the identification of possible sources as LFMO waste, fertilizer, or unidentified animal or mixtures of these sources. Additional evidence provided by ribotyping and wastewater organic compound data can, in some cases, specifically indicate the animal source. Detections of three or more wastewater organic compounds that are indicators of animal sources and detections of fecal coliform bacteria provided additional evidence of an animal source. LMFO waste was designated as a possible source of nitrate in water from 10 wells. The source of waste in water from five of those wells was determined through ribotyping, and the source of waste in water from the remaining five wells was determined by detections of three or more animal-waste compounds in the well samples. LMFO waste in the water from wells with unidentified animal source of nitrate does not indicate that LMFO waste was not the source, but indicated that multiple animal sources, including LMFO waste, may be the source of the nitrate.

Direct Human Contact with Siloxanes (Silicones) – Safety or Risk Part 1. Characteristics of Siloxanes (Silicones)

PubMed Central

Mojsiewicz-Pieńkowska, Krystyna; Jamrógiewicz, Marzena; Szymkowska, Katarzyna; Krenczkowska, Dominika

2016-01-01

Siloxanes are commonly known as silicones. They belong to the organosilicon compounds and are exclusively obtained by synthesis. Their chemical structure determines a range of physicochemical properties which were recognized as unique. Due to the susceptibility to chemical modifications, ability to create short, long or complex polymer particles, siloxanes found an application in many areas of human life. Siloxanes differ in particle size, molecular weight, shape and chemical groups. As a result, this determines the different physico-chemical properties, that directly affect the safety or the risk of their use. The areas that can be a source of danger to human health will be commented in this paper. PMID:27303296

Regional aeolian dynamics and sand mixing in the Gran Desierto - Evidence from Landsat Thematic Mapper images

NASA Technical Reports Server (NTRS)

Blount, Grady; Greeley, Ronald; Christensen, Phillip R.; Smith, Milton O.; Adams, John B.

1990-01-01

Mesoscale mapping of spatial variations in sand composition of the Gran Desierto (Sonora, Mexico) was carried out on multispectral Landsat TM images of this region, making it possible to examine the dynamic development of sand sheets and dunes. Compositions determined from remote imagery were found to agree well with samples from selected areas. The sand populations delineated were used to describe the sediment source areas, transport paths, and deposition sites. The image analysis revealed important compositional variations aver large areas that were not readily apparent in the field data.

Source geometric considerations for OMEGA Dante measurements

DOE Office of Scientific and Technical Information (OSTI.GOV)

May, M. J.; Patterson, J. R.; Widmann, K.

2012-10-15

The Dante is a 15 channel filtered diode array which is installed on the OMEGA laser facility at the Laboratory for Laser Energetics, University of Rochester. The system yields the spectrally and temporally resolved radiation flux from 50 eV to 10 keV from various targets (i.e., Hohlraum, gas pipes, etc.). The absolute flux is determined from the radiometric calibration of the x-ray diodes, filters, and mirrors and an unfold algorithm applied to the recorded voltages from each channel. The unfold algorithm assumes an emitting source that is spatially uniform and has a constant area as a function of photon energy.more » The emitting x-ray source is usually considered to be the laser entrance hole (LEH) of a given diameter for Hohlraum type targets or the effective wall area of high conversion efficiency K-shell type targets. This assumption can be problematic for several reasons. High intensity regions or 'hot spots' in the x-ray are observed where the drive laser beams strike the target. The 'hot spots' create non-uniform emission seen by the Dante. Additionally, thinned walled (50 {mu}m) low-Z targets (C{sub 22}H{sub 10}N{sub 2}O{sub 5}) have an energy dependent source size since the target's walls will be fully opaque for low energies (E < 2-3 keV) yet fully transmissive at higher energies. Determining accurate yields can be challenging for these types of targets. Discussion and some analysis will be presented.« less

Source geometric considerations for OMEGA Dante measurements

DOE Office of Scientific and Technical Information (OSTI.GOV)

May, M. J.; Patterson, J. R.; Sorce, C.

2012-10-01

The Dante is a 15 channel filtered diode array which is installed on the OMEGA laser facility at the Laboratory for Laser Energetics, University of Rochester. The system yields the spectrally and temporally resolved radiation flux from 50 eV to 10 keV from various targets (i.e., Hohlraum, gas pipes, etc.). The absolute flux is determined from the radiometric calibration of the x-ray diodes, filters, and mirrors and an unfold algorithm applied to the recorded voltages from each channel. The unfold algorithm assumes an emitting source that is spatially uniform and has a constant area as a function of photon energy.more » The emitting x-ray source is usually considered to be the laser entrance hole (LEH) of a given diameter for Hohlraum type targets or the effective wall area of high conversion efficiency K-shell type targets. This assumption can be problematic for several reasons. High intensity regions or “hot spots” in the x-ray are observed where the drive laser beams strike the target. The “hot spots” create non-uniform emission seen by the Dante. Additionally, thinned walled (50 μm) low-Z targets (C22H10N2O5) have an energy dependent source size since the target's walls will be fully opaque for low energies (E < 2–3 keV) yet fully transmissive at higher energies. Determining accurate yields can be challenging for these types of targets. Discussion and some analysis will be presented.« less

Biogeochemical snapshot of an urban water system: The Anacostia River, Washington DC

NASA Astrophysics Data System (ADS)

Macavoy, S.; Ewers, E.; Bushaw-Newton, K.

2007-12-01

Highly urbanized and contaminated with PAHs, heavy metals, and sewage, the Anacostia River flows through Maryland and Washington, DC into the tidal Potomac River. Efforts have been underway to assess the river's ecological integrity and to determine the extent of anthropogenic influences. This study examines the nutrients, bacterial biomarkers, organic material, and carbon, nitrogen and sulfur sources in the Anacostia. High biological oxygen demand and low nitrogen (0.33-0.56 mg /L)/phosphorus (0.014 - 0.021 mg/L) concentrations were observed in three areas of the river. Bacterial activity based on carbon source utilization was higher in sediment samples than in water column samples. While bacterial abundances were decreased in downstream areas of sediment; abundances increased in downstream areas in the water column. Downstream sites had higher nutrient concentrations and dissolved organic carbon (up to 13.7 mg/L). Odd-chain length and branched fatty acids (FAs) in the sediments indicated bacterial sources, but long chain FAs indicative of terrestrial primary production were also abundant in some sediments. Also dominant among methyl esters and ketones in some sediment and water column samples was methyl isobutyl ketone, a common industrial solvent and combustion by-product. Sediment carbon stable isotope analyses show a mix of autochthonous and allochthonous derived materials, but most carbon was derived from terrestrial sources (-23.3 to -31.7°). Sediment nitrogen stable isotopes ranged from -5.4 to. 5.6, showing nitrate uptake by plants and also recycling of nitrogen within the river. Sulfur sources were generally between 3 and -5, reflecting local sulfate sources and anaerobic sulfate reduction.

An integrated system for the determination of the local, regional and long-transport contributions to Particulate Matter concentrations

NASA Astrophysics Data System (ADS)

Amodio, M.; Andriani, E.; Daresta, B. E.; de Gennaro, G.; di Gilio, A.; Ielpo, P.,; Placentino, C. M.; Trizio, L.; Tutino, M.

2010-05-01

Several epidemiological studies have shown the negative effects of air pollution on human health, which range from respiratory and cardiovascular disease to neurotoxic effects, and cancer. Most recent investigations have been focused on health toxicological features of Particulate Matter (PM) and its interactions with other pollutants: it was found that fine particles (PM2.5) could be an effective media to transport these pollutants deeply into the lung and to cause many kind of reactions which include oxidative stress, local pulmonary and systemic inflammatory responses (Künzli and Perez, 2009). Based on these implications on public health, many countries have developed plans to suggest effective control strategies which involve the identification of Particulate Matter sources, the quantitative estimation of the emission rates of the pollutants, the understanding of PM transport, mixing and transformation processes and the identification of main factors influencing PM concentrations. In this field, receptor models can be useful tools to estimate sources contributions to PM collected in an area under investigations. Different approaches to receptor model analysis can be distinguished on basis of whether chemical characteristics of emission sources are required to be known before the source apportionment. The multivariate approach could be preferred when a lack of information concerning sources profiles occurred (Hopke, 2003). In this work, the results obtained by applying an integrated approach in the monitoring of PM using several typologies of instrumentations will be shown. A prototype for the determination of the contributions of a single source (‘fugitive emission') on the fine PM concentrations has been developed: it consists of a Swam dual-channel sampler, an OPC Monitor, a sonic anemometer and a PBL Mixing monitor. The investigated site chosen for the application of prototype will be the iron and steel pole of Taranto (Apulia Region, South of Italy). Fugitive emission campaign will be performed by using three different positions around the Taranto industrial area; the main interest on Taranto is due to the presence of several activities of high impact as very wide industrial area close to the town and the numerous maritime and military activities in the harbour area (Amodio et al., 2008). The aim is to triangulate the area of the examined source on the basis of the prevalent directions of the wind. The investigation will be completed by chemical-physical characterization of PM2.5 and PM10 samples collected by the prototype in order to have additional information about the possible emissive sources. The statistical analysis, performed by Principal Component Analysis (PCA) and Positive Matrix Factorization (PMF), will be used for a detailed study of the impact of the local emissive source on the neighboring areas. Finally, the prototype will allow to identify and distinguish long range transport, regional and other local contributions on the fine PM concentrations. This work was supported by the Strategic Project PS_122 founded by Apulia Region. References Künzli, N., Perez, L., 2009. Swiss Medical Weekly 139(17-18), 242-250. Hopke, P.K., 2003. Journal of Chemometrics 17(5), 255-265. Amodio, M., Caselli, M., Daresta, B.E., de Gennaro, G., Ielpo, P., Placentino, C.M., Tutino, 2008. Chemical Engineering Transactions 16, 193-199.

Sources of fine sediment stored in agricultural lowland streams, Midwest, USA

NASA Astrophysics Data System (ADS)

Lamba, Jasmeet; Thompson, A. M.; Karthikeyan, K. G.; Fitzpatrick, Faith A.

2015-05-01

Agricultural activities can accelerate the offsite transport of productive soil from fields leading to stream water quality degradation. Identification of the nature and relative contribution of different sources to fine-grained sediment (e.g., silts, clays) in streams is important to effectively focus agricultural best management practices in watersheds. Sediment fingerprinting techniques through the use of geochemical tracers are commonly used to differentiate relative contribution from various sources. Research was conducted in lowland streams in the Pleasant Valley watershed in South Central Wisconsin (USA) to identify provenance of fine-grained sediment deposits and evaluate the impact of land use on relative contributions from the following potential sources: cropland, pasture, woodland, and eroding stream banks. Results show that both agriculture (croplands and pastures) and eroding stream banks are primary sources to fine sediment deposits on the stream bed with contributions ranging from 19 to 100% and 0 to 81%, respectively. The increase in area under agricultural land use within a subwatershed results in greater contribution from agriculture (R2 = 0.846, p = 0.0034). Relative contributions from eroding stream banks increased with increasing area under grasslands and woodlands within a subwatershed (R2 = 0.814, p = 0.0055). Subwatersheds with greater mass of fine sediment deposited on the stream bed per unit area should be prioritized for best management practices. The conservation practices should be targeted to stream banks or croplands depending on the dominant source of fine sediment within a subwatershed. Site specific changes in relative contributions from different sources to fine-grained sediment in this watershed highlights the complexities involved in sediment transport dynamics. The nested sampling sites helped determine that sediment dynamics at the subwatershed scale need to be considered for application of targeted conservation techniques.

Sources of fine sediment stored in agricultural lowland streams, Midwest, USA

USGS Publications Warehouse

Lamba, Jasmeet; Thompson, Anita M.; Karthikeyan, K.G.; Fitzpatrick, Faith A.

2015-01-01

Agricultural activities can accelerate the offsite transport of productive soil from fields leading to stream water quality degradation. Identification of the nature and relative contribution of different sources to fine-grained sediment (e.g., silts, clays) in streams is important to effectively focus agricultural best management practices in watersheds. Sediment fingerprinting techniques through the use of geochemical tracers are commonly used to differentiate relative contribution from various sources. Research was conducted in lowland streams in the Pleasant Valley watershed in South Central Wisconsin (USA) to identify provenance of fine-grained sediment deposits and evaluate the impact of land use on relative contributions from the following potential sources: cropland, pasture, woodland, and eroding stream banks. Results show that both agriculture (croplands and pastures) and eroding stream banks are primary sources to fine sediment deposits on the stream bed with contributions ranging from 19 to 100% and 0 to 81%, respectively. The increase in area under agricultural land use within a subwatershed results in greater contribution from agriculture (R2 = 0.846, p = 0.0034). Relative contributions from eroding stream banks increased with increasing area under grasslands and woodlands within a subwatershed (R2 = 0.814, p = 0.0055). Subwatersheds with greater mass of fine sediment deposited on the stream bed per unit area should be prioritized for best management practices. The conservation practices should be targeted to stream banks or croplands depending on the dominant source of fine sediment within a subwatershed. Site specific changes in relative contributions from different sources to fine-grained sediment in this watershed highlights the complexities involved in sediment transport dynamics. The nested sampling sites helped determine that sediment dynamics at the subwatershed scale need to be considered for application of targeted conservation techniques.

Overview of the Texas Source Water Assessment Project

USGS Publications Warehouse

Ulery, Randy L.

2000-01-01

The 1996 Amendments to the Safe Drinking Water Act require, for the first time, that each state prepare a source water assessment for all PWS. Previously, Federal regulations focused on sampling and enforcement with emphasis on the quality of delivered water. These Amendments emphasize the importance of protecting the source water. States are required to determine the drinking-water source, the origin of contaminants monitored or the potential contaminants to be monitored, and the intrinsic susceptibility of the source water. Under the amendments to the Act, States must create SWAP Programs. The programs must include an individual source water assessment for each public water system regulated by the State. These assessments will determine whether an individual drinking water source is susceptible to contamination. During 1997?99, TNRCC and USGS staff met as subject-matter working groups to develop an approach to conducting Source Water Susceptibility Assessments (SWSA) and a draft workplan. The draft workplan was then presented to and reviewed by various stakeholder and technical advisory groups. Comments and suggestions from these groups were considered, and a final workplan was produced and presented to the EPA. After EPA approval, work formally began on the Texas SWAP Project. The project has an expected completion date of September 2002. At that time, initial SWSA of all Texas public water supplies should be complete. Ground-water supplies can be considered susceptible if a possible source of contamination (PSOC) exists in the contributing area for the public-supply well field or spring, the contaminant travel time to the well field or spring is short, and the soil zone, vadose zone, and aquifer-matrix materials are unlikely to adequately attenuate the contaminants associated with the PSOC. In addition, particular types of land use/cover within the contributing area may cause the supply to be deemed more susceptible to contamination. Finally, detection of various classes of constituents in water from wells in the vicinity of a public supply well may indicate susceptibility of the public-supply well even though there may be no identifiable PSOC or land use activity. Surface-water supplies are by nature susceptible to contamination from both point and non-point sources. The degree of susceptibility of a PWS to contamination can vary and is a function of the environmental setting, water and wastewater management practices, and land use/cover within a water supply's contributing watershed area. For example, a PWS intake downstream from extensive urban development may be more susceptible to non-point source contamination than a PWS intake downstream from a forested, relatively undeveloped watershed. Surface-water supplies are also susceptible to contamination from point sources, which may include permitted discharges, as well as accidental spills or other introduction of contaminants.

Effect of mass housing settlement type on the comfortable open areas in terms of noise.

PubMed

Akdağ, Neşe Yüğrük; Gedik, Gülay Zorer; Kiraz, Fatih; Şener, Bekir

2017-09-12

The layout of the structures according to the noise source is an important parameter in terms of the level of noise reaching to both open usage areas and the structure surfaces. In this paper, it is aimed to reveal the effect of mass housing settlement type on the size of suitable open usage areas in terms of noise. Comfortable open usage areas in 25 mass housing alternatives are determined for the case of being affected by three different road noises. The reliability of the simulation results is validated by on-site noise level measurements. As a result, it is seen that better results are obtained in linear, L, C, and U type alternatives than point-type blocks. Especially in alternatives consisting of point-and linear-type blocks, if the noise level is above 75 Leq (dBA), the percentage of comfortable open usage areas is very low. It is determined that the percentage of comfortable open areas increases between 50 and 100% by means of appropriately designed noise barriers.

Multi-anode wire two dimensional proportional counter for detecting Iron-55 X-Ray Radiation

NASA Astrophysics Data System (ADS)

Weston, Michael William James

Radiation detectors in many applications use small sensor areas or large tubes which only collect one-dimensional information. There are some applications that require analyzing a large area and locating specific elements such as contamination on the heat tiles of a space shuttle or features on historical artifacts. The process can be time consuming and scanning a large area in a single pass is beneficial. The use of a two dimensional multi-wire proportional counter provides a large detection window presenting positional information in a single pass. This thesis described the design and implementation of an experimental detector to evaluate a specific design intended for use as a handheld instrument. The main effort of this research was to custom build a detector for testing purposes. The aluminum chamber and all circuit boards were custom designed and built specifically for this application. Various software and programmable logic algorithms were designed to analyze the raw data in real time and attempted to determine what data was useful and what could be discarded. The research presented here provides results useful for designing an improved second generation detector in the future. With the anode wire spacing chosen and the minimal collimation of the radiation source, detected events occurred all over the detection grid at any time. The raw event data did not make determining the source position easy and further data correlation was required. An abundance of samples had multiple wire hits which were not useful because it falsely reported the source to be all over the place and at different energy levels. By narrowing down the results to only use the largest signal pairs on different axes in each event, a much more accurate analysis of where the source existed above the grid was determined. The basic principle and construction method was shown to work, however the gas selection, geometry and anode wire constructs proved to be poor. To provide a system optimized for a specific application would require detailed Monte Carlo simulations. These simulation results together with the details and techniques implemented in this thesis would provide a final instrument of much higher accuracy.

Use of Spatial Sampling and Microbial Source-Tracking Tools for Understanding Fecal Contamination at Two Lake Erie Beaches

USGS Publications Warehouse

Francy, Donna S.; Bertke, Erin E.; Finnegan, Dennis P.; Kephart, Christopher M.; Sheets, Rodney A.; Rhoades, John; Stumpe, Lester

2006-01-01

Source-tracking tools were used to identify potential sources of fecal contamination at two Lake Erie bathing beaches: an urban beach (Edgewater in Cleveland, Ohio) and a beach in a small city (Lakeshore in Ashtabula, Ohio). These tools included identifying spatial patterns of Escherichia coli (E. coli) concentrations in each area, determining weather patterns that caused elevated E. coli, and applying microbial source tracking (MST) techniques to specific sites. Three MST methods were used during this study: multiple antibiotic resistance (MAR) indexing of E. coli isolates and the presence of human-specific genetic markers within two types of bacteria, the genus Bacteroides and the species Enterococcus faecium. At Edgewater, sampling for E. coli was done during 2003-05 at bathing-area sites, at nearshore lake sites, and in shallow ground water in foreshore and backshore areas. Spatial sampling at nearshore lake sites showed that fecal contamination was most likely of local origin; E. coli concentrations near the mouths of rivers and outfalls remote to the beach were elevated (greater than 235 colony-forming units per 100 milliliters (CFU/100 mL)) but decreased along transport pathways to the beach. In addition, E. coli concentrations were generally highest in bathing-area samples collected at 1- and 2-foot water depths, midrange at 3-foot depths, and lowest in nearshore lake samples typically collected 150 feet from the shoreline. Elevated E. coli concentrations at bathing-area sites were generally associated with increased wave heights and rainfall, but not always. E. coli concentrations were often elevated in shallow ground-water samples, especially in samples collected less than 10 feet from the edge of water (near foreshore area). The interaction of shallow ground water and waves may be a mechanism of E. coli storage and accumulation in foreshore sands. Infiltration of bird feces through sand with surface water from rainfall and high waves may be concentrating E. coli in shallow ground water in foreshore and backshore sands. At Lakeshore, sampling for E. coli was done at bathing-area, nearshore lake, and parking-lot sites during 2004-05. Low concentrations of E. coli at nearshore lake sites furthest from the shoreline indicated that fecal contamination was most likely of local origin. High concentrations of E. coli in water and bed sediments at several nearshore lake sites showed that contamination was emanating from several points along the shoreline during wet and dry weather, including the boat ramp, an area near the pond drainage, and parking-lot sediments. Physical evidence confirmed that runoff from the parking lot leads to degradation of water quality at the beach. MST samples were collected to help interpret spatial findings and determine whether sources of fecal contamination were from wastewater or bird feces and if a human-specific marker was present. MAR indices were useful in distinguishing between bird feces and wastewater sources because they were about 10 times higher in the latter. The results from MAR indices agreed with results from the two human-specific markers in some but not all of the samples tested. Bacteroides and enterococci human-specific markers were found on one day at Edgewater and two days at Lakeshore. On three days at Edgewater and two days at Lakeshore, the MAR index indicated a mixed source, but neither marker was found in bathing-water samples; this may be because bacterial indicator concentrations were too low to detect a marker. Multiple tools are needed to help identify sources of fecal contamination at coastal beaches. Spatial sampling identified patterns in E. coli concentrations and yielded information on the physical pathways of contamination. MST methods provided information on whether the source was likely of human or nonhuman origin only; however, MST did not provide information on the pathways of contamination.

Quantification of 5'-deoxy-5'-methylthioadenosine in heat-treated natural rubber latex serum.

PubMed

Pitakpornpreecha, Thanawat; Plubrukarn, Anuchit; Wititsuwannakul, Rapepun

2012-01-01

5'-Deoxy-5'-methylthioadenosine (MTA) is one of the biologically active components found in natural rubber latex (NRL) serum, a common waste product from rubber plantations. In this study the contents of MTA in heat-treated NRL serum were measured in order to assess the potential of the serum as an alternative source of MTA. To devise an HPLC/UV-based quantitative analytical protocol for the determination of MTA, and to determine the effect of heat treatment on the content of MTA in NRL serum from various sources. An HPLC/UV-based determination of MTA using an acidic eluant was devised and validated. In the heat treatment, the effect of refluxing times on MTA liberation was evaluated. The quantification protocol was validated with satisfying linearity, limits of detection and quantitation, precisions for peak areas and recovery percentages from intra- and inter-day operations. The amounts of MTA in the NRL sera from various sources increased with heat treatment to yield 5-12 μg MTA/mL of serum. The devised protocol was found to be satisfyingly applicable to the routine determination of MTA in NRL serum. The effect of heat treatment on the content of MTA also indicated another possible use for NRL serum, normally discarded in vast amounts by the rubber industry, as an alternative source of MTA. Copyright © 2011 John Wiley & Sons, Ltd.

Assessing the impact of industrial source emissions on atmospheric carbonaceous aerosol concentrations using routine monitoring networks.

PubMed

Sheesley, Rebecca J; Schauer, James J; Orf, Marya L

2010-02-01

Industrial sources can have a significant but poorly defined impact on ambient particulate matter concentrations in select areas. Detailed emission profiles are often not available and are hard to develop because of the diversity of emissions across time and space at large industrial complexes. A yearlong study was conducted in an industrial area in Detroit, MI, which combined real-time particle mass (tapered element oscillating microbalance) and black carbon (aetholometer) measurements with molecular marker measurements of monthly average concentrations as well as daily concentrations of select high pollution days. The goal of the study was to use the real-time data to define days in which the particulate matter concentration in the atmosphere was largely impacted by local source emissions and to use daily speciation data to derive emission profiles for the industrial source. When combined with motor vehicle exhaust, wood smoke and road dust profiles, the industrial source profile was used to determine the contribution of the local industrial source to the total organic carbon (OC) concentrations using molecular marker-chemical mass balance modeling (MM-CMB). The MM-CMB analysis revealed that the industrial source had minimal impact on the monthly average carbonaceous aerosol concentration, but contributed approximately 2 microg m(-3), or a little over one-third of the total OC, on select high-impact days.

Lead isotopes in lichen transplants around a Cu smelter in Russia determined by MC-ICP-MS reveal transient records of multiple sources.

PubMed

Spiro, B; Weiss, D J; Purvis, O W; Mikhailova, I; Williamson, B J; Coles, B J; Udachin, V

2004-12-15

Transplants of the lichen Hypogymnia physodes, which is relatively tolerant to SO2 and heavy metals, were deployed for 3 months over a 60 km long SW-NE transect centered on a highly polluting Cu smelter and its adjoining town of Karabash, southern Urals, Russia. The abundance of 206Pb, 207Pb, 208Pb, and 204Pb were determined by MC-ICP-MS. The measurement of 204Pb revealed critical features, which would otherwise remain concealed: (i) The precise isotope ratios referenced to 204Pb allowed several different sources to be resolved even within the small area covered: (a) the obvious pollutant source of the Karabash Cu smelter; (b) two dispersed sources, likely to include soil with lower and different contributions of thorogenic and uranogenic lead; and (c) one anthropogenic source with higher contribution of 235U derived Pb. (ii) In part of the transect, the Pb isotope composition changed while the Pb concentrations remained the same. This indicates that the Pb content of the transplantation material from the background site was largely replaced and that the transplants provide a transient record reflecting a continuous accumulation and loss of environmental Pb, probably mainly in the form of extracellular particles. Overall, the method of lichen transplantation coupled with Pb isotope ratio determinations proved effective in assessing the usefulness of lichens in biomonitoring and in resolving different sources of atmospheric deposition.

Lessons learnt from the Wenchuan earthquake: performance evaluation of treatment of critical injuries in hardest-hit areas.

PubMed

Jiang, Jie; Li, Youping; Huang, Xiaolin; Li, Bing; Su, Lin; Zhong, Dake; Shi, Chenghu; Li, Mingxu; Shan, Juan; Chen, Yin

2012-08-01

Critical injury treatment in the hardest-hit areas after a great earthquake was retrospectively analyzed to determine how best to reduce mortality and disability and increase the rehabilitation rate through postquake medical relief. Retrospective analysis, primary sources, and secondary sources were comprehensively retrieved and analyzed. According to incomplete data, 30,620 injured were rescued by themselves among the hardest-hit areas in the 72 hours immediately following the earthquake. Critically injured patients accounted for 22% of total inpatients. Mortality rates declined with greater distance from the epicenter: rates were 12.21% for municipal healthcare centers in the hardest-hit areas, 4.50% for municipal medical units in peripheral quake-hit areas, 2.50% for provincial medical units in peripheral quake-hit areas, and 2.17% for Ministry of Health-affiliated hospitals in peripheral quake-hit areas. The number of injured with fractures on body, limbs or unknown-parts, severe conditions as well as other kinds of non-traumatic diseases received in second-line hospitals was much more than those treated in first-line hospitals with more severe injuries. Among 10,373 injured in stable condition transferred to third-line hospitals, 99.07% were discharged from hospitals within four months, while the mortality rate was 0.017%. The medical relief model of "supervising body helping subordinate unit, severely stricken areas assisting hardest-hit areas, least-hit areas supporting both hardest-hit and severely stricken areas, and self help and mutual assistance applied between hardest-hit areas" was roughly established for injured from severely stricken areas after the Wenchuan Earthquake. The "four-centralization" treatment principle, which referred to concentrating patients, experts, resources and treatment for those injured in critical condition effectively reduced the mortality from 15.06% to 2.9%. Timely, scientific, and standard on-site triage and postmedical transfer guided by accurate injury information determine rescue effect for the injured, while there is large space to fulfill as for treatment for critical diseases among the hardest-hit areas under extreme conditions after the Wenchuan earthquake. © 2012 Wiley Publishing Asia Pty Ltd and Chinese Cochrane Center, West China Hospital of Sichuan University.

Source parameters for small events associated with the 1986 North Palm Springs, California, earthquake determined using empirical Green functions

USGS Publications Warehouse

Mori, J.; Frankel, A.

1990-01-01

Using small events as empirical Green functions, source parameters were estimated for 25 ML 3.4 to 4.4 events associated with the 1986 North Palm Springs earthquake. The static stress drops ranged from 3 to 80 bars, for moments of 0.7 to 11 ?? 1021 dyne-cm. There was a spatial pattern to the stress drops of the aftershocks which showed increasing values along the fault plane toward the northwest compared to relatively low values near the hypocenter of the mainshock. The highest values were outside the main area of slip, and are believed to reflect a loaded area of the fault that still has an higher level of stress which was not released during the main shock. -from Authors

Plume mapping and isotopic characterisation of anthropogenic methane sources

NASA Astrophysics Data System (ADS)

Zazzeri, G.; Lowry, D.; Fisher, R. E.; France, J. L.; Lanoisellé, M.; Nisbet, E. G.

2015-06-01

Methane stable isotope analysis, coupled with mole fraction measurement, has been used to link isotopic signature to methane emissions from landfill sites, coal mines and gas leaks in the United Kingdom. A mobile Picarro G2301 CRDS (Cavity Ring-Down Spectroscopy) analyser was installed on a vehicle, together with an anemometer and GPS receiver, to measure atmospheric methane mole fractions and their relative location while driving at speeds up to 80 kph. In targeted areas, when the methane plume was intercepted, air samples were collected in Tedlar bags, for δ13C-CH4 isotopic analysis by CF-GC-IRMS (Continuous Flow Gas Chromatography-Isotope Ratio Mass Spectrometry). This method provides high precision isotopic values, determining δ13C-CH4 to ±0.05 per mil. The bulk signature of the methane plume into the atmosphere from the whole source area was obtained by Keeling plot analysis, and a δ13C-CH4 signature, with the relative uncertainty, allocated to each methane source investigated. Both landfill and natural gas emissions in SE England have tightly constrained isotopic signatures. The averaged δ13C-CH4 for landfill sites is -58 ± 3‰. The δ13C-CH4 signature for gas leaks is also fairly constant around -36 ± 2‰, a value characteristic of homogenised North Sea supply. In contrast, signatures for coal mines in N. England and Wales fall in a range of -51.2 ± 0.3‰ to -30.9 ± 1.4‰, but can be tightly constrained by region. The study demonstrates that CRDS-based mobile methane measurement coupled with off-line high precision isotopic analysis of plume samples is an efficient way of characterising methane sources. It shows that isotopic measurements allow type identification, and possible location of previously unknown methane sources. In modelling studies this measurement provides an independent constraint to determine the contributions of different sources to the regional methane budget and in the verification of inventory source distribution.

Prospects for Pulsar Studies with the GLAST Large Area Telescope

NASA Technical Reports Server (NTRS)

Harding, Alice K.

2006-01-01

The Large Area Telescope (LAT) on the Gamma-ray Large Area Space Telescope (GLAST) will have unprecedented sensitivity and energy resolution for gamma-rays in the range of 30 MeV to 200 GeV. GLAST is therefore expected to provide major advances in the understanding of high-energy emission from rotation-powered pulsars. As the only presently known galactic GeV source class, pulsars will be one of the most important sources for study with GLAST. The main science goals of the LAT for pulsar studies include an increase in the number of detected radio-loud and radio-quiet gamma ray pulsars, including millisecond pulsars, giving much better statistics for elucidating population characteristics, measurement of the high-energy spectrum and the shape of spectral cutoffs and determining pulse profiles for a variety of pulsars of different age. Further, measurement of phase-resolved spectra and energy dependent pulse profiles of the brighter pulsars should allow detailed tests of magnetospheric particle acceleration and radiation mechanisms, by comparing data with theoretical models that have been developed. Additionally, the LAT will have the sensitivity to allow blind pulsation searches of nearly all unidentified EGRET sources, to possibly uncover more radio-quiet Geminga-like pulsars.

Inverse problem and variation method to optimize cascade heat exchange network in central heating system

NASA Astrophysics Data System (ADS)

Zhang, Yin; Wei, Zhiyuan; Zhang, Yinping; Wang, Xin

2017-12-01

Urban heating in northern China accounts for 40% of total building energy usage. In central heating systems, heat is often transferred from heat source to users by the heat network where several heat exchangers are installed at heat source, substations and terminals respectively. For given overall heating capacity and heat source temperature, increasing the terminal fluid temperature is an effective way to improve the thermal performance of such cascade heat exchange network for energy saving. In this paper, the mathematical optimization model of the cascade heat exchange network with three-stage heat exchangers in series is established. Aim at maximizing the cold fluid temperature for given hot fluid temperature and overall heating capacity, the optimal heat exchange area distribution and the medium fluids' flow rates are determined through inverse problem and variation method. The preliminary results show that the heat exchange areas should be distributed equally for each heat exchanger. It also indicates that in order to improve the thermal performance of the whole system, more heat exchange areas should be allocated to the heat exchanger where flow rate difference between two fluids is relatively small. This work is important for guiding the optimization design of practical cascade heating systems.

Status, sources, and human health risk assessment of PAHs via foliar dust from different functional areas in Nanjing, China.

PubMed

Zha, Yan; Zhang, Yin L; Tang, Jie; Sun, Kai

2018-05-12

The present study was carried out to assess and understand the potential health risk, level of contamination, composition pattern, and sources of urban foliar dust in Nanjing City with respect to polycyclic aromatic hydrocarbons (PAHs). Five urban functional areas of foliar dust were analysed and the contents of 16 priority PAHs were determined. Total PAH concentrations in foliar dust ranged from 1.77 to 19.02 μg·g -1 , with an average value of 6.98 μg·g -1 . The PAH pattern was dominated by four and five-ring PAHs (contributing > 38% of total PAHs) in all of the five functional areas. The results indicated that the combustion of fossil fuel, coal, and biomass, as well as vehicle traffic emissions were the major sources of PAHs. The estimated incremental lifetime cancer risk due to PAHs in foliar dust were 8.19 × 10 -6 , 6.63 × 10 -6 , and 9.65 × 10 -6 for childhood, adolescence and adulthood, respectively, indicating a high risk of cancer from exposure to foliar dust in Nanjing. Our results indicated that foliar dust might be a useful indicator of atmospheric PAH pollution.

Land Use Change, Fuel Use and Respiratory Health in Uganda

PubMed Central

Jagger, Pamela; Shively, Gerald

2014-01-01

This paper examines how biomass supply and consumption are affected by land use change in Uganda. We find that between 2007 and 2012 there was a 22% reduction in fuelwood sourced from proximate forests, and an 18% increase in fuelwood sourced from fallows and other areas with lower biomass availability and quality. We estimate a series of panel regression models and find that deforestation has a negative effect on total fuel consumed. We also find that access to forests, whether through ownership or proximity, plays a large role in determining fuel use. We then explore whether patterns of biomass fuel consumption are related to the incidence of acute respiratory infection using a cross-sectional data set of 1209 women and 598 children. We find a positive and significant relationship between ARI and the quantity of fuelwood from non-forest areas; a 100 kilogram increase in fuelwood sourced from a non-forest area results in a 2.4% increase in the incidence of ARI for children. We find the inverse effect of increased reliance on crop residues. As deforestation reduces the availability of high quality fuelwood, rural households may experience higher incidence of health problems associated with exposure to biomass burning. PMID:24535892

Occurrence and sources of Escherichia coli in metropolitan St. Louis streams, October 2004 through September 2007

USGS Publications Warehouse

Wilkison, Donald H.; Davis, Jerri V.

2010-01-01

The occurrence and sources of Escherichia coli (E. coli), one of several fecal indicator bacteria, in metropolitan St. Louis streams known to receive nonpoint source runoff, occasional discharges from combined and sanitary sewers, and treated wastewater effluent were investigated from October 2004 through September 2007. Three Missouri River sites, five Mississippi River sites, and six small basin tributary stream sites were sampled during base flow and storm events for the presence of E. coli and their sources. E. coli host-source determinations were conducted using local library based genotypic methods. Human fecal contamination in stream samples was additionally confirmed by the presence of Bacteroides thetaiotaomicron, an anaerobic, enteric bacterium with a high occurrence in, and specificity to, humans. Missouri River E. coli densities and loads during base flow were approximately 10 times greater than those in the Mississippi River above its confluence with the Missouri River. Although substantial amounts of E. coli originated from within the study area during base flow and storm events, considerable amounts of E. coli in the Missouri River, as well as in the middle Mississippi River sections downstream from its confluence with the Missouri River, originated in Missouri River reaches upstream from the study area. In lower Mississippi River reaches, bacteria contributions from the numerous combined and sanitary sewer overflows within the study area, as well as contributions from nonpoint source runoff, greatly increased instream E. coli densities. Although other urban factors cannot be discounted, average E. coli densities in streams were strongly correlated with the number of upstream combined and sanitary sewer overflow points, and the percentage of upstream impervious cover. Small basin sites with the greatest number of combined and sanitary sewer overflows (Maline Creek and the River des Peres) had larger E. coli densities, larger loads, and a greater percentage of E. coli attributable to humans than other small basin sites; however, even though small basin E. coli densities typically were much larger than in large river receiving streams, small basins contributed, on average, only a small part (a maximum of 16 percent) of the total E. coli load to larger rivers. On average, approximately one-third of E. coli in metropolitan St. Louis streams was identified as originating from humans. Another one-third of the E. coli was determined to have originated from unidentified sources; dogs and geese contributed lesser amounts, 10 and 20 percent, of the total instream bacteria. Sources of E. coli were largely independent of hydrologic conditions-an indication that sources remained relatively consistent with time.

Predators

USGS Publications Warehouse

Young, Donald D.; McCabe, Thomas R.; Ambrose, Robert E.; Garner, Gerald W.; Weiler, Greg J.; Reynolds, Harry V.; Udevitz, Mark S.; Reed, Dan J.; Griffith, Brad; Douglas, David C.; Reynolds, Patricia E.; Rhode, E.B.

2002-01-01

Calving caribou (Rangifer tarandus) of the Central Arctic herd, Alaska, have avoided the infrastructure associated with the complex of petroleum development areas from Prudhoe Bay to Kuparuk (Cameron et al. 1992, Nellemann and Cameron 1998, and Section 4 of this document). Calving females of the Porcupine caribou herd may similarly avoid any oil field roads and pipelines developed in areas traditionally used during the calving and post-calving periods. This may displace the caribou females and calves to areas east and south of the 1002 Area of the Arctic National Wildlife Refuge.Increased calf mortality could occur if calving caribou are displaced into areas that have a higher density of predators, higher rates of predation, or where a higher proportion of the predators regularly use caribou as a food source (Whitten et al. 1992).Our study assessed predation risks to caribou calving in the 1002 Area versus calving in potential displacement areas. Due to funding constraints, our research focused on grizzly bears (Ursus arctos), with wolves (Camus lupus) and golden eagles (Aquila chrysaetos) receiving only cursory attention. Our research objectives were 1) to compare relative abundance of predators within the 1002 Area with that in adjacent peripheral areas, 2) to determine factors affecting predator abundance on the calving grounds, and 3) to quantify the use of caribou as a food source for predators and the importance of caribou to the productivity of predator populations using the coastal plain of the Arctic National Wildlife Refuge.

COMBUSTION AREA SOURCES: DATA SOURCES

EPA Science Inventory

The report identifies, documents, and evaluates data sources for stationary area source emissions, including solid waste and agricultural burning. Area source emissions of particulate matter, sulfur dioxide, oxides of nitrogen, reactive volatile organic compounds, and carbon mon...

Determining the sources of fine-grained sediment using the Sediment Source Assessment Tool (Sed_SAT)

USGS Publications Warehouse

Gorman Sanisaca, Lillian E.; Gellis, Allen C.; Lorenz, David L.

2017-07-27

A sound understanding of sources contributing to instream sediment flux in a watershed is important when developing total maximum daily load (TMDL) management strategies designed to reduce suspended sediment in streams. Sediment fingerprinting and sediment budget approaches are two techniques that, when used jointly, can qualify and quantify the major sources of sediment in a given watershed. The sediment fingerprinting approach uses trace element concentrations from samples in known potential source areas to determine a clear signature of each potential source. A mixing model is then used to determine the relative source contribution to the target suspended sediment samples.The computational steps required to apportion sediment for each target sample are quite involved and time intensive, a problem the Sediment Source Assessment Tool (Sed_SAT) addresses. Sed_SAT is a user-friendly statistical model that guides the user through the necessary steps in order to quantify the relative contributions of sediment sources in a given watershed. The model is written using the statistical software R (R Core Team, 2016b) and utilizes Microsoft Access® as a user interface but requires no prior knowledge of R or Microsoft Access® to successfully run the model successfully. Sed_SAT identifies outliers, corrects for differences in size and organic content in the source samples relative to the target samples, evaluates the conservative behavior of tracers used in fingerprinting by applying a “Bracket Test,” identifies tracers with the highest discriminatory power, and provides robust error analysis through a Monte Carlo simulation following the mixing model. Quantifying sediment source contributions using the sediment fingerprinting approach provides local, State, and Federal land management agencies with important information needed to implement effective strategies to reduce sediment. Sed_SAT is designed to assist these agencies in applying the sediment fingerprinting approach to quantify sediment sources in the sediment TMDL framework.

Biomonitoring of PAHs by using Quercus ilex leaves: Source diagnostic and toxicity assessment

NASA Astrophysics Data System (ADS)

De Nicola, Flavia; Claudia, Lancellotti; MariaVittoria, Prati; Giulia, Maisto; Anna, Alfani

2011-03-01

Quercus ilex L. leaves were sampled at nineteen urban sites and two remote sites in order to evaluate PAH contamination degree. One-, two- and three-year-old leaves were collected and leaf lipid content was measured to investigate the influence of leaf age and lipids in PAH accumulation. Some PAH diagnostic ratios, such as Ant/Ant + Phen, Flt/Flt + Pyr, B[a]A/B[a]A + Crys and IP/IP + B[g,h,i]P, were calculated. The results suggest that Q. ilex leaves are effective biomonitors of PAH air contamination: in fact, a great PAH accumulation in leaves from the urban areas, until 30-time higher compared to those from the remote sites, has been observed. At each site, the similar total PAH concentrations in leaves of different age, probably due to a canopy effect, indicate an ability of all leaf age classes to monitor local PAH concentrations in air, remarking practical implications for air biomonitoring. The findings suggest that PAH adsorption in Q. ilex leaves does not result limited by leaf lipid content. Moreover, this study demonstrates the source-diagnostic potential of Q. ilex leaves, because, in particular, the Flt/Flt + Pyr and IP/IP + B[g,h,i]P ratios indicate vehicular traffic as the main source of PAHs in the urban areas and wood combustion in the remote areas. Moreover, to distinguish biomass combustion source, a promising tracer PAH as DB[a,h]A could be used. The high contribution of DB[a,h]A to total PAH concentrations at the remote sites determines a high carcinogenic potential in this area, similar to that calculated for the urban area where the carcinogenic PAH concentrations in absolute values are often higher.

Source parameters of microearthquakes on an interplate asperity off Kamaishi, NE Japan over two earthquake cycles

USGS Publications Warehouse

Uchida, Naoki; Matsuzawa, Toru; Ellsworth, William L.; Imanishi, Kazutoshi; Shimamura, Kouhei; Hasegawa, Akira

2012-01-01

We have estimated the source parameters of interplate earthquakes in an earthquake cluster off Kamaishi, NE Japan over two cycles of M~ 4.9 repeating earthquakes. The M~ 4.9 earthquake sequence is composed of nine events that occurred since 1957 which have a strong periodicity (5.5 ± 0.7 yr) and constant size (M4.9 ± 0.2), probably due to stable sliding around the source area (asperity). Using P- and S-wave traveltime differentials estimated from waveform cross-spectra, three M~ 4.9 main shocks and 50 accompanying microearthquakes (M1.5–3.6) from 1995 to 2008 were precisely relocated. The source sizes, stress drops and slip amounts for earthquakes of M2.4 or larger were also estimated from corner frequencies and seismic moments using simultaneous inversion of stacked spectral ratios. Relocation using the double-difference method shows that the slip area of the 2008 M~ 4.9 main shock is co-located with those of the 1995 and 2001 M~ 4.9 main shocks. Four groups of microearthquake clusters are located in and around the mainshock slip areas. Of these, two clusters are located at the deeper and shallower edge of the slip areas and most of these microearthquakes occurred repeatedly in the interseismic period. Two other clusters located near the centre of the mainshock source areas are not as active as the clusters near the edge. The occurrence of these earthquakes is limited to the latter half of the earthquake cycles of the M~ 4.9 main shock. Similar spatial and temporal features of microearthquake occurrence were seen for two other cycles before the 1995 M5.0 and 1990 M5.0 main shocks based on group identification by waveform similarities. Stress drops of microearthquakes are 3–11 MPa and are relatively constant within each group during the two earthquake cycles. The 2001 and 2008 M~ 4.9 earthquakes have larger stress drops of 41 and 27 MPa, respectively. These results show that the stress drop is probably determined by the fault properties and does not change much for earthquakes rupturing in the same area. The occurrence of microearthquakes in the interseismic period suggests the intrusion of aseismic slip, causing a loading of these patches. We also found that some earthquakes near the centre of the mainshock source area occurred just after the earthquakes at the deeper edge of the mainshock source area. These seismic activities probably indicate episodic aseismic slip migrating from the deeper regions in the mainshock asperity to its centre during interseismic periods. Comparison of the source parameters for the 2001 and 2008 main shocks shows that the seismic moments (1.04 x 1016 Nm and 1.12 x 1016 Nm for the 2008 and 2001 earthquakes, respectively) and source sizes (radius = 570 m and 540 m for the 2008 and 2001 earthquakes, respectively) are comparable. Based on careful phase identification and hypocentre relocation by constraining the hypocentres of other small earthquakes to their precisely located centroids, we found that the hypocentres of the 2001 and 2008 M~ 4.9 events are located in the southeastern part of the mainshock source area. This location does not correspond to either episodic slip area or hypocentres of small earthquakes that occurred during the earthquake cycle.

Research on the Placement of the Ecological Shelter Zone in the Three Gorges Reservoir Area, China

NASA Astrophysics Data System (ADS)

Shan, N.; Ruan, X.

2011-12-01

The Three Gorges Dam is built on the middle reaches of Yangtze River (Changjiang) in south-central China, which is the world's third longest river. The Three Gorges Reservoir Region (TGRR), including the entire inundated area and 19 administrative units (counties and cities) on both sides of the river, is regarded as an environmentally sensitive area. The total area of the TGRR is approximately 58000 km2. As the Three Gorges Dam fully operated, for the flood control, the water level should be kept in the range between 145 m and 175 m and the reservoir surface water area(over 1080 km2)at a water level of 175 m, with a length of 600 km. Many of cities, villages and farms have been submerged. Moreover, as a result of reservoir operation, the water-level alternation of the reservoir is opposite to the nature, which is low water level (145m) in summer and high water level (175m) in winter. The Hydro-Fluctuation Belt, with a height of 30m, will become a new pollution source due to the riparian being flooded and the submerged areas may still contain trace amounts of toxic or radioactive materials. The environmental impacts associated with large scale reservoir area often have significant negative impacts on the environment. It affects forest cover, species in the area, some endangered, water quality, increase the likelihood of earthquakes and mudslides in the area. To solve these problems, it is necessarily to construct the Ecological Shelter Zone (ESZ) along with the edge of the reservoir area. The function of the ESZ is similar to the riparian zone in reducing flood damage, improving water quality, decreasing the levels of the nonpoint source pollution load and soil erosion and rebuilding the migration routes of plant and wildlife. However, the research of the ESZ is mainly focused on rivers at field scale by now, lack of research method on reservoir at the watershed scale. As the special nature of the Three Gorges Reservoir, the construction of the ESZ in the TGRA is very complex. This paper focus on the development of a methodology to target the ESZ based on currently available tools (Remote Sensing, GIS and Hydrologic Model). According to the features of the TGRR, a spatially explicit and process-based method was introduced to help plan the placement of the ESZ in the TGRR for water quality benefits. The methods presented here were based on the integration of grid-based terrain analysis and nonpoint source pollution estimates. Firstly, the contribution of nonpoint source pollution from upslope farmland and urban to the TGRR was determined by grid-based terrain analysis. The upslope contributing area beyond the ESZ was defined as a "source". The SWAT model was used to analyze the characteristics of the pollution load. Secondly, the ESZ was defined as a "sink" and the reducing pollution loads in each grid cell of the ESZ was calculated by the REMM model. Finally, the key areas in the TGRA where the ESZ have the greatest potential to improve water quality were identified and the formula of the width of the ESZ was determined. However, the method in this article considers only the function of pollutants reduction in the ESZ, the next stage of the study will involve detailed modeling for the function of ecological corridor in the ESZ.

Distribution, richness, quality, and thermal maturity of source rock units on the North Slope of Alaska

USGS Publications Warehouse

Peters, K.E.; Bird, K.J.; Keller, M.A.; Lillis, P.G.; Magoon, L.B.

2003-01-01

Four source rock units on the North Slope were identified, characterized, and mapped to better understand the origin of petroleum in the area: Hue-gamma ray zone (Hue-GRZ), pebble shale unit, Kingak Shale, and Shublik Formation. Rock-Eval pyrolysis, total organic carbon analysis, and well logs were used to map the present-day thickness, organic quantity (TOC), quality (hydrogen index, HI), and thermal maturity (Tmax) of each unit. To map these units, we screened all available geochemical data for wells in the study area and assumed that the top and bottom of the oil window occur at Tmax of ~440° and 470°C, respectively. Based on several assumptions related to carbon mass balance and regional distributions of TOC, the present-day source rock quantity and quality maps were used to determine the extent of fractional conversion of the kerogen to petroleum and to map the original organic richness prior to thermal maturation.

SENSITIVITY OF BLIND PULSAR SEARCHES WITH THE FERMI LARGE AREA TELESCOPE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dormody, M.; Johnson, R. P.; Atwood, W. B.

2011-12-01

We quantitatively establish the sensitivity to the detection of young to middle-aged, isolated, gamma-ray pulsars through blind searches of Fermi Large Area Telescope (LAT) data using a Monte Carlo simulation. We detail a sensitivity study of the time-differencing blind search code used to discover gamma-ray pulsars in the first year of observations. We simulate 10,000 pulsars across a broad parameter space and distribute them across the sky. We replicate the analysis in the Fermi LAT First Source Catalog to localize the sources, and the blind search analysis to find the pulsars. We analyze the results and discuss the effect ofmore » positional error and spin frequency on gamma-ray pulsar detections. Finally, we construct a formula to determine the sensitivity of the blind search and present a sensitivity map assuming a standard set of pulsar parameters. The results of this study can be applied to population studies and are useful in characterizing unidentified LAT sources.« less

LINES OF EVIDENCE FOR NA FOR ORGANIC COMPOUNDS AND THE USE OF COMPOUND SPECIFIC ISOTOPE ANALYSIS

EPA Science Inventory

The strongest line of evidence is a reduction in concentration over time. However, this only provides evidence of natural attenuation of the source area. It is difficult to determine the rate of natural attenuation through biodegradation with distance along a flow path in the a...

40 CFR 63.775 - Reporting requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... documentation stating why the TEG dehydration unit must operate using the alternate glycol circulation rate. (iv... facility will always operate the glycol dehydration unit using the optimum circulation rate determined in... dehydration unit located at an area source that meets the criteria in § 63.764(e)(1)(i) or § 63.764(e)(1)(ii...

43 CFR 404.44 - What criteria will Reclamation apply to determine whether it is appropriate to recommend that a...

Code of Federal Regulations, 2010 CFR

2010-10-01

... THE INTERIOR RECLAMATION RURAL WATER SUPPLY PROGRAM Appraisal Investigations § 404.44 What criteria... in the investigation, whether the alternative: (1) Identifies viable water supplies and water rights sufficient to supply the proposed service area, including all practicable water sources such as lower quality...

SPECIATION OF ARSENIC IN EDIBLE BIOTA TO SUPPORT RISK ASSESSMENT DETERMINATION OF RELATIVE SOURCE CONTRIBUTION FOR ARSENIC

EPA Science Inventory

The Office of Research and Development has designated the study of arsenic as a high priority research area because of the health risk associated from exposure to this element. Present monitoring efforts are primarily focused on total concentration of arsenic in drinking water. ...

Field determination of multipollutant, open area combustion source emission factors with a hexacopter unmanned aerial vehicle

EPA Science Inventory

An emission sensor/sampler system was coupled to a NASA hexacopter unmanned aerial system (UAS) to characterize gases and particles in the plume emitted from open burning of military ordnance. The UAS/sampler was tested at two field sites resulting in 33 flights at Radford, VA a...

A Study of Existing Pre-vocational Agriculture Programs in Iowa.

ERIC Educational Resources Information Center

Hansen, Barbara Ann; Miller, W. Wade

A study was conducted to determine what subject areas should be taught in a prevocational agriculture program, as perceived by instructors with existing prevocational programs. Following a review of literature that found only a few sources on prevocational agriculture programs, most of them guides for middle school curricula, a survey instrument…

Drug Impact Index.

ERIC Educational Resources Information Center

Western Center for Drug-Free Schools and Communities.

The Drug Impact Index provides a set of indicators designed to determine the extent of the local drug problem in a community. Each indicator includes a technical note on the data sources, a graph showing comparative statistics on that indicator for the Portland area and for the State of Oregon, and brief remarks on the implications of the data.…

Causes for Attrition Among Adult Basic Education Students.

ERIC Educational Resources Information Center

Cramer, Patricia L.

This study was conducted to determine causes for attrition among students in an Adult Basic Education (A.B.E.) program located in a non-metropolitan area. Dropouts and completers were compared by demographic characteristics and by sources of difficulty (nonschool-related, school-related, and affective) in attending class. In addition, causes for…

Sources of Science Teaching Self-Efficacy for Preservice Elementary Teachers in Science Content Courses

ERIC Educational Resources Information Center

Menon, Deepika; Sadler, Troy D.

2018-01-01

Self-efficacy beliefs play a major role in determining teachers' science teaching practices and have been a topic of great interest in the area of preservice science teacher education. This qualitative study investigated factors that influenced preservice elementary teachers' science teaching self-efficacy beliefs in a physical science content…

A screening procedure to evaluate air pollution effects on Class I wilderness areas

Treesearch

Douglas G. Fox; Ann M. Bartuska; James G. Byrne; Ellis Cowling; Richard Fisher; Gene E. Likens; Steven E. Lindberg; Rick A. Linthurst; Jay Messer; Dale S. Nichols

1989-01-01

This screening procedure is intended to help wilderness managers conduct "adverse impact determinations" as part of Prevention of Significant Deterioration (PSD) applications for sources that emit air pollutants that might impact Class I wildernesses. The process provides an initial estimate of susceptibility to critical loadings for sulfur, nitrogen, and...

75 FR 54073 - Medicaid Program; Withdrawal of Determination of Average Manufacturer Price, Multiple Source Drug...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-03

... hospital that is located outside of a Metropolitan Statistical Area for Medicare payment regulations and... reserved. 4. Section 447.510 is amended by-- A. Republishing paragraph (a) introductory text. B. Revising.... Revising the introductory text of paragraph (b). C. Revising paragraph (c). The revisions read as follows...

The use of ARL trajectories for the evaluation of precipitation chemistry data

Treesearch

John M. Miller; James N. Galloway; Gene E. Likens

1976-01-01

One of the major problems in interpreting precipitation chemistry data is determining the possible source areas of the materials found in the precipitation. To investigate this problem, the trajectory program developed at Air Resources Laboratories (NOAA) was used to compute five-day backward air trajectories from Ithaca, New York.

Analysis of the Source System of Nantun Group in Huhehu Depression of Hailar Basin

NASA Astrophysics Data System (ADS)

Li, Yue; Li, Junhui; Wang, Qi; Lv, Bingyang; Zhang, Guannan

2017-10-01

Huhehu Depression will be the new battlefield in Hailar Basin in the future, while at present it’s in a low exploration level. The study about the source system of Nantun group is little, so fine depiction of the source system would be significant to sedimentary system reconstruction, the reservoir distribution and prediction of favorable area. In this paper, it comprehensive uses of many methods such as ancient landform, light and heavy mineral combination, seismic reflection characteristics, to do detailed study about the source system of Nantun group in different views and different levels. The results show that the source system in Huhehu Depression is from the east of Xilinbeir bulge and the west of Bayan Moutain uplift, which is surrounded by basin. The slope belt is the main source, and the southern bulge is the secondary source. The distribution of source system determines the distribution of sedimentary system and the regularity of the distribution of sand body.

Geospatial Analysis of Atmospheric Haze Effect by Source and Sink Landscape

NASA Astrophysics Data System (ADS)

Yu, T.; Xu, K.; Yuan, Z.

2017-09-01

Based on geospatial analysis model, this paper analyzes the relationship between the landscape patterns of source and sink in urban areas and atmospheric haze pollution. Firstly, the classification result and aerosol optical thickness (AOD) of Wuhan are divided into a number of square grids with the side length of 6 km, and the category level landscape indices (PLAND, PD, COHESION, LPI, FRAC_MN) and AOD of each grid are calculated. Then the source and sink landscapes of atmospheric haze pollution are selected based on the analysis of the correlation between landscape indices and AOD. Next, to make the following analysis more efficient, the indices selected before should be determined through the correlation coefficient between them. Finally, due to the spatial dependency and spatial heterogeneity of the data used in this paper, spatial autoregressive model and geo-weighted regression model are used to analyze atmospheric haze effect by source and sink landscape from the global and local level. The results show that the source landscape of atmospheric haze pollution is the building, and the sink landscapes are shrub and woodland. PLAND, PD and COHESION are suitable for describing the atmospheric haze effect by source and sink landscape. Comparing these models, the fitting effect of SLM, SEM and GWR is significantly better than that of OLS model. The SLM model is superior to the SEM model in this paper. Although the fitting effect of GWR model is more unsuited than that of SLM, the influence degree of influencing factors on atmospheric haze of different geography can be expressed clearer. Through the analysis results of these models, following conclusions can be summarized: Reducing the proportion of source landscape area and increasing the degree of fragmentation could cut down aerosol optical thickness; And distributing the source and sink landscape evenly and interspersedly could effectively reduce aerosol optical thickness which represents atmospheric haze pollution; For Wuhan City, the method of adjusting the built-up area slightly and planning the non-built-up areas reasonably can be taken to reduce atmospheric haze pollution.

Investigation of large-area multicoil inductively coupled plasma sources using three-dimensional fluid model

NASA Astrophysics Data System (ADS)

Brcka, Jozef

2016-07-01

A multi inductively coupled plasma (ICP) system can be used to maintain the plasma uniformity and increase the area processed by a high-density plasma. This article presents a source in two different configurations. The distributed planar multi ICP (DM-ICP) source comprises individual ICP sources that are not overlapped and produce plasma independently. Mutual coupling of the ICPs may affect the distribution of the produced plasma. The integrated multicoil ICP (IMC-ICP) source consists of four low-inductance ICP antennas that are superimposed in an azimuthal manner. The identical geometry of the ICP coils was assumed in this work. Both configurations have highly asymmetric components. A three-dimensional (3D) plasma model of the multicoil ICP configurations with asymmetric features is used to investigate the plasma characteristics in a large chamber and the operation of the sources in inert and reactive gases. The feasibility of the computational calculation, the speed, and the computational resources of the coupled multiphysics solver are investigated in the framework of a large realistic geometry and complex reaction processes. It was determined that additional variables can be used to control large-area plasmas. Both configurations can form a plasma, that azimuthally moves in a controlled manner, the so-called “sweeping mode” (SM) or “polyphase mode” (PPM), and thus they have the potential for large-area and high-density plasma applications. The operation in the azimuthal mode has the potential to adjust the plasma distribution, the reaction chemistry, and increase or modulate the production of the radicals. The intrinsic asymmetry of the individual coils and their combined operation were investigated within a source assembly primarily in argon and CO gases. Limited investigations were also performed on operation in CH4 gas. The plasma parameters and the resulting chemistry are affected by the geometrical relation between individual antennas. The aim of this work is to incorporate the technological, computational, dimensional scaling, and reaction chemistry aspects of the plasma under one computational framework. The 3D simulation is utilized to geometrically scale up the reactive plasma that is produced by multiple ICP sources.

Separating the air quality impact of a major highway and nearby sources by nonparametric trajectory analysis.

PubMed

Henry, Ronald C; Vette, Alan; Norris, Gary; Vedantham, Ram; Kimbrough, Sue; Shores, Richard C

2011-12-15

Nonparametric Trajectory Analysis (NTA), a receptor-oriented model, was used to assess the impact of local sources of air pollution at monitoring sites located adjacent to highway I-15 in Las Vegas, NV. Measurements of black carbon, carbon monoxide, nitrogen oxides, and sulfur dioxide concentrations were collected from December 2008 to December 2009. The purpose of the study was to determine the impact of the highway at three downwind monitoring stations using an upwind station to measure background concentrations. NTA was used to precisely determine the contribution of the highway to the average concentrations measured at the monitoring stations accounting for the spatially heterogeneous contributions of other local urban sources. NTA uses short time average concentrations, 5 min in this case, and constructed local back-trajectories from similarly short time average wind speed and direction to locate and quantify contributions from local source regions. Averaged over an entire year, the decrease of concentrations with distance from the highway was found to be consistent with previous studies. For this study, the NTA model is shown to be a reliable approach to quantify the impact of the highway on local air quality in an urban area with other local sources.

Application of crossed beam technology to direct measurements of sound sources in turbulent jets, part 1

NASA Technical Reports Server (NTRS)

Wilson, L. N.

1970-01-01

The mathematical bases for the direct measurement of sound source intensities in turbulent jets using the crossed-beam technique are discussed in detail. It is found that the problems associated with such measurements lie in three main areas: (1) measurement of the correct flow covariance, (2) accounting for retarded time effects in the measurements, and (3) transformation of measurements to a moving frame of reference. The determination of the particular conditions under which these problems can be circumvented is the main goal of the study.

Evaluation of mercury contamination using plant leaves and humus as indicators

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tamura, R.; Fukuzaki, N.; Hirano, Y.

Plant leaves and humus were collected from three areas with and without mercury emission sources. Mercury in these samples were determined by cold flameless atomic absorption spectrometry. A part of mercury emitted from the source into the atmosphere is absorbed by plant leaves, and move to humus through fallen leaves. Consequently, plant leaves are able to be used as an indicator for the evaluation of mercury in air at present. Humus is useful for the evaluation of mercury contamination through the air from the past to present.

Land-use controls on sources and processing of nitrate in small watersheds: Insights from dual isotopic analysis

USGS Publications Warehouse

Barnes, R.T.; Raymond, P.A.

2010-01-01

Studies have repeatedly shown that agricultural and urban areas export considerably more nitrogen to streams than forested counterparts, yet it is difficult to identify and quantify nitrogen sources to streams due to complications associated with terrestrial and in-stream biogeochemical processes. In this study, we used the isotopic composition of nitrate (??15N-NO3- and ??18O- NO3-) in conjunction with a simple numerical model to examine the spatial and temporal variability of nitrate (NO3-) export across a land-use gradient and how agricultural and urban development affects net removal mechanisms. In an effort to isolate the effects of land use, we chose small headwater systems in close proximity to each other, limiting the variation in geology, surficial materials, and climate between sites. The ??15N and ??18Oof stream NO 3- varied significantly between urban, agricultural, and forested watersheds, indicating that nitrogen sources are the primary determinant of the ??15N-NO3-, while the ??18O-NO3- was found to reflect biogeochemical processes. The greatest NO3- concentrations corresponded with the highest stream ??15N-NO3- values due to the enriched nature of two dominant anthropogenic sources, septic and manure, within the urban and agricultural watersheds, respectively. On average, net removal of the available NO3- pool within urban and agricultural catchments was estimated at 45%. The variation in the estimated net removal of NO3- from developed watersheds was related to both drainage area and the availability of organic carbon. The determination of differentiated isotopic land-use signatures and dominant seasonal mechanisms illustrates the usefulness of this approach in examining the sources and processing of excess nitrogen within headwater catchments. ?? 2010 by the Ecological Society of America.

Stormwater runoff characterized by GIS determined source areas and runoff volumes.

PubMed

Liu, Yang; Soonthornnonda, Puripus; Li, Jin; Christensen, Erik R

2011-02-01

Runoff coefficients are usually considered in isolation for each drainage area with resulting large uncertainties in the areas and coefficients. Accurate areas and coefficients are obtained here by optimizing runoff coefficients for characteristic Geographic Information Systems (GIS) subareas within each drainage area so that the resulting runoff coefficients of each drainage area are consistent with those obtained from runoff and rainfall volumes. Lack of fit can indicate that the ArcGIS information is inaccurate or more likely, that the drainage area needs adjustment. Results for 18 drainage areas in Milwaukee, WI for 2000-2004 indicate runoff coefficients ranging from 0.123 for a mostly residential area to 0.679 for a freeway-related land, with a standard error of 0.047. Optimized runoff coefficients are necessary input parameters for monitoring, and for the analysis and design of in situ stormwater unit operations and processes for the control of both urban runoff quantity and quality.

Sources and Focus of Health Development Assistance, 1990-2014.

PubMed

Dieleman, Joseph L; Graves, Casey; Johnson, Elizabeth; Templin, Tara; Birger, Maxwell; Hamavid, Hannah; Freeman, Michael; Leach-Kemon, Katherine; Singh, Lavanya; Haakenstad, Annie; Murray, Christopher J L

2015-06-16

The governments of high-income countries and private organizations provide billions of dollars to developing countries for health. This type of development assistance can have a critical role in ensuring that life-saving health interventions reach populations in need. To identify the amount of development assistance that countries and organizations provided for health and to determine the health areas that received these funds. Budget, revenue, and expenditure data on the primary agencies and organizations (n = 38) that provided resources to developing countries (n = 146-183, depending on the year) for health from 1990 through 2014 were collected. For each channel (the international agency or organization that directed the resources toward the implementing institution or government), the source and recipient of the development assistance were determined and redundant accounting of the same dollar, which occurs when channels transfer funds among each other, was removed. This research derived the flow of resources from source to intermediary channel to recipient. Development assistance for health (DAH) was divided into 11 mutually exclusive health focus areas, such that every dollar of development assistance was assigned only 1 health focus area. Since 1990, $458.0 billion of development assistance has been provided to maintain or improve health in developing countries. The largest source of funding was the US government, which provided $143.1 billion between 1990 and 2014, including $12.4 billion in 2014. Of resources that originated with the US government, 70.6% were provided through US government agencies, and 41.0% were allocated for human immunodeficiency virus (HIV)/AIDS. The second largest source of development assistance for health was private philanthropic donors, including the Bill and Melinda Gates Foundation and other private foundations, which provided $69.9 billion between 1990 and 2014, including $6.2 billion in 2014. These resources were provided primarily through private foundations and nongovernmental organizations and were allocated for a diverse set of health focus areas. Since 1990, 28.0% of all DAH was allocated for maternal health and newborn and child health; 23.2% for HIV/AIDS, 4.3% for malaria, 2.8% for tuberculosis, and 1.5% for noncommunicable diseases. Between 2000 and 2010, DAH increased 11.3% annually. However, since 2010, total DAH has not increased as substantially. Funding for health in developing countries has increased substantially since 1990, with a focus on HIV/AIDS, maternal health, and newborn and child health. Funding from the US government has played a substantial role in this expansion. Funding for noncommunicable diseases has been limited. Understanding how funding patterns have changed across time and the priorities of sources of international funding across distinct channels, recipients, and health focus areas may help identify where funding gaps persist and where cost-effective interventions could save lives.

Water Sources and Their Protection from the Impact of Microbial Contamination in Rural Areas of Beijing, China

PubMed Central

Ye, Bixiong; Yang, Linsheng; Li, Yonghua; Wang, Wuyi; Li, Hairong

2013-01-01

Bacterial contamination of drinking water is a major public health problem in rural China. To explore bacterial contamination in rural areas of Beijing and identify possible causes of bacteria in drinking water samples, water samples were collected from wells in ten rural districts of Beijing, China. Total bacterial count, total coliforms and Escherichia coli in drinking water were then determined and water source and wellhead protection were investigated. The bacterial contamination in drinking water was serious in areas north of Beijing, with the total bacterial count, total coliforms and Escherichia coli in some water samples reaching 88,000 CFU/mL, 1,600 MPN/100 mL and 1,600 MPN/100 mL, respectively. Water source types, well depth, whether the well was adequately sealed and housed, and whether wellhead is above or below ground were the main factors influencing bacterial contamination levels in drinking water. The bacterial contamination was serious in the water of shallow wells and wells that were not closed, had no well housing or had a wellhead below ground level. The contamination sources around wells, including village dry toilets and livestock farms, were well correlated with bacterial contamination. Total bacterial counts were affected by proximity to sewage ditches and polluting industries, however, proximity to landfills did not influence the microbial indicators. PMID:23462436

Comparative Study of Lunar Roughness from Multi - Source Data

NASA Astrophysics Data System (ADS)

Lou, Y.; Kang, Z.

2017-07-01

The lunar terrain can show its collision and volcanic history. The lunar surface roughness can give a deep indication of the effects of lunar surface magma, sedimentation and uplift. This paper aims to get different information from the roughness through different data sources. Besides introducing the classical Root-mean-square height method and Morphological Surface Roughness (MSR) algorithm, this paper takes the area of the Jurassic mountain uplift in the Sinus Iridum and the Plato Crater area as experimental areas. And then make the comparison and contrast of the lunar roughness derived from LRO's DEM and CE-2 DOM. The experimental results show that the roughness obtained by the traditional roughness calculation method reflect the ups and downs of the topography, while the results obtained by morphological surface roughness algorithm show the smoothness of the lunar surface. So, we can first use the surface fluctuation situation derived from RMSH to select the landing area range which ensures the lands are gentle. Then the morphological results determine whether the landing area is suitable for the detector walking and observing. The results obtained at two different scales provide a more complete evaluation system for selecting the landing site of the lunar probe.

Investigation of gasoline distributions within petrol stations: spatial and seasonal concentrations, sources, mitigation measures, and occupationally exposed symptoms.

PubMed

Sairat, Theerapong; Homwuttiwong, Sahalaph; Homwutthiwong, Kritsana; Ongwandee, Maneerat

2015-09-01

We measured levels of VOCs and determined the distributions of benzene concentrations over the area of two petrol stations in all three seasons. Using the concentrations and sampling positions, we created isoconcentration contour maps. The average concentrations ranged 18-1288 μg m(-3) for benzene and 12-81 μg m(-3) for toluene. The contour maps indicate that high-level contours of benzene were found not only at the fuel dispenser areas but also at the storage tank refilling points, open drainage areas where gasoline-polluted wastewater was flowing, and the auto service center located within the station area. An assessment of the benzene to toluene ratio contour plots implicates that airborne benzene and toluene near the fuel dispenser area were attributed to gasoline evaporation although one of the studied stations may be influenced by other VOC sources besides gasoline evaporation. Additionally, during the routine refilling of the underground fuel storage tanks by a tank truck, the ambient levels of benzene and toluene increased tremendously. The implementation of source control by replacing old dispensers with new fuel dispensers that have an efficient cutoff feature and increased delivery speed can reduce spatial benzene concentrations by 77%. Furthermore, a questionnaire survey among 63 service attendants in ten stations revealed that headache was the most reported health complaint with a response rate of 32%, followed by fatigue with 20%. These prominent symptoms could be related to an exposure to high benzene concentrations.

Speed of CMEs and the Magnetic Non-Potentiality of Their Source ARs

NASA Technical Reports Server (NTRS)

Tiwari, Sanjiv K.; Falconer, David A.; Moore, Ronald L.; Venkatakrishnan, P.

2014-01-01

Most fast coronal mass ejections (CMEs) originate from solar active regions (ARs). Non-potentiality of ARs is expected to determine the speed and size of CMEs in the outer corona. Several other unexplored parameters might be important as well. To find out the correlation between the initial speed of CMEs and the non-potentiality of source ARs, we associated over a hundred of CMEs with source ARs via their co-produced flares. The speed of the CMEs are collected from the SOHO LASCO CME catalog. We have used vector magnetograms obtained mainly with HMI/SDO, also with Hinode (SOT/SP) when available within an hour of a CME occurrence, to evaluate various magnetic non-potentiality parameters, e.g. magnetic free-energy proxies, computed magnetic free energy, twist, shear angle, signed shear angle etc. We have also included several other parameters e.g. total unsigned flux, net current, magnetic area of ARs, area of sunspots, to investigate their correlation, if any, with the initial speeds of CMEs. Our preliminary results show that the ARs with larger non-potentiality and area mostly produce fast CMEs but they can also produce slower ones. The ARs with lesser non-potentiality and area generally produce only slower CMEs, however, there are a few exceptions. The total unsigned flux correlate with the non-potentiality parameters and area of ARs but some ARs with large unsigned flux are also found to be least non-potential. A more detailed analysis is underway.

Nutrient export from watersheds on Mt. Desert Island, maine, as a function of land use and fire history

USGS Publications Warehouse

Nielsen, M.G.; Kahl, J.S.

2007-01-01

A study of 13 small (less than 7.5 km2) watersheds on Mt. Desert Island, Maine, was conducted from January 1999 to September 2000 to determine nutrient export delivery to coastal waters around the island, and to determine whether a series of wildfires in 1947 have affected nutrient export in burned watersheds. Nutrient export (nitrate-nitrogen, total nitrogen, total phosphorus) was determined for each watershed during the study period, and was normalized by watershed area. The yield of nitrate-nitrogen (N) ranged from 10 to 140 kg/km2/year. Total N yield ranged from 42 to 250 kg/ km2/year. Total phosphorus (P) yield ranged from 1.4 to 7.9 kg/km2/year. Watersheds entirely within Acadia National Park (lacking human land-based nutrient sources) exported significantly less total N and total P than watersheds that were partly or entirely outside the park boundary. Nitrate-N export was not significantly different in these two groups of watersheds, perhaps because atmospheric deposition is a dominant source of nitrate in the study area. No relation was observed between burn history and nutrient export. Any effect of burn history may be masked by other landscape-level factors related to nutrient export. ?? Springer Science + Business Media B.V. 2007.

Recent changes in the oxidized to reduced nitrogen ratio in atmospheric precipitation

NASA Astrophysics Data System (ADS)

Kurzyca, Iwona; Frankowski, Marcin

2017-10-01

In this study, the characteristics of precipitation in terms of various nitrogen forms (NO3-, NO2-, NH4+, Norganic, Ntotal) is presented. The samples were collected in the areas of different anthropogenic pressure (urban area vs. ecologically protected woodland area, ∼30 km distant from each other; Wielkopolska region, Poland). Based on the Nox and Nred emission profiles (Nox/Nred ratio), temporal and spatial comparison was carried out. For both sites, during a decade of observation, more than 60% of samples had higher contribution of N-NH4+ than N-NO3-, the amount of N-NO2- was negligible, and organic nitrogen amounted to 30% of total nitrogen content which varied up to 16 mg/l. The precipitation events w ith high concentration of nitrogen species were investigated in terms of possible local and remote sources of nitrogen (synoptic meteorology), to indicate the areas which can act as potential sources of N-compounds. Based on the chemometric analysis, it was found that Nred implies Nox and vice versa, due to interactions between them in the atmosphere. Taking into account the analysis of precipitation occurring simultaneously in both locations (about 50% of all rainfall episodes), it was observed that such factor as anthropogenic pressure differentiates but does not determine the chemical composition of precipitation in the investigated areas (urban vs. woodland area; distance of ∼30 km). Thermodynamics of the atmosphere had a significant impact on concentrations of N-NO3- and N-NH4+ in precipitation, as well as the circulation of air masses and remote N sources responsible for transboundary inflow of pollutants.

The effects of dust on Colorado mountain snow cover albedo and compositional links to dust-source areas

NASA Astrophysics Data System (ADS)

Goldstein, H. L.; Reynolds, R. L.; Landry, C.; Derry, J. E.; Kokaly, R. F.; Breit, G. N.

2016-12-01

Dust deposited on mountain snow cover (DOS) changes snow albedo, enhances absorption of solar radiation, and effectively increases rates of snow melt, leading to earlier-than-normal runoff and overall smaller late-season water supplies for tens of millions of people and industries in the American West. Visible-spectrum reflectance of DOS samples is on the order of 0.2 (80% absorption), in stark contrast to the high reflectivity of pure snow which approaches 1.0. Samples of DOS were collected from 12 high-elevation Colorado mountain sites near the end of spring from 2013 through 2016 prior to complete snow melt, when most dust layers had merged into one layer. These samples were analyzed to measure dust properties that affect snow albedo and to link DOS to dust-source areas. Dust mass loadings to snow during water year 2014 varied from 5 to 30 g/m2. Median particle sizes centered around 20 micrometers with more than 80% of the dust <63 micrometers. Dark minerals, carbonaceous matter, and iron oxides, including nano-sized hematite and goethite, together diminished reflectance according to their variable concentrations. Documenting variations in dust-particle masses, sizes, and compositions helps determine their influences on snow-melt and may be useful for modeling snow-melt effects from future dust. Furthermore, variations in dust components and particle sizes lead to new ways to recognize sources of dust by comparison with properties of fine-grained sediments in dust-source areas. Much of the DOS in the San Juan Mountains, Colorado can be linked to southern Colorado Plateau source areas by compositional similarities and satellite imagery. Understanding dust properties that affect snow albedo and recognizing the sources of dust deposited on snow cover may guide mitigation of dust emission that affects water resources of the Colorado River basin.

Predicting S2S in Deep Time Sedimentary Systems and Implications for Petroleum Systems

NASA Astrophysics Data System (ADS)

Bhattacharya, J.

2013-12-01

The source to sink concept is focused on quantification of the various components of siliciclastic sedimentary systems from initial source areas, through the dispersal system, and deposition within a number of potential ultimate sedimentary sinks. Sequence stratigraphy shows that depositional system are linked through time and show distinctively predictable 3D stratigraphic organization, which can be related to cycles of relative changes in accommodation and sediment supply. For example, erosion and formation of incised fluvial valleys generally occur during periods of falling base level with lowstand reservoir deposits favored in more basin distal settings (e.g. deepwater fans), whereas during highstands of sea level, significantly more sediment may be sequestered in the non-marine realm and more distal environments may favor deposition of slowly-deposited condensed sections, which may make excellent hydrocarbon source rocks. Only more recently have attempts been made to quantify the size and scaling relationships of the ultimate source areas on the basis of analysis of ancient depositional systems, and the use of these scaling relationships to predict the sixe of linked depositional systems along the S2S tract. The maximum size of depositional systems, such as rivers, deltas, and submarine fans, is significantly controlled by the area, relief, and climate regime of the source area, which in turn may linked to the plate tectonic and paleogeographic setting. Classic provenance studies, and more recent use of detrital zircons, provide critical information about source-areas, and may help place limits on the size and relief of a drainage basin. Provenance studies may also provide key information about rates of exhumation of source areas and the link to the tectonic setting, Examination of ancient river systems in the rock record, and especially the largest trunk rivers, which are typically within incised valleys, can also be used to estimate paleodischarge, which in turn can be linked to the drainage basin to make estimates about the size and sale of the source area. The best estimates can be made in basins with well-constrained data that allow details of cross-sectional or plan-view channel-architecture to be determined, such as extensive outcrops, or abundant subsurface data, and especially where higher resolution 3D seismic data are available. Paleodischarge estimates of lowstand Quaternary-age continental-scale ancient rivers from passive continental margins, using seismic data, are orders-of-magnitude higher (1000's of cumecs) than smaller-scale Cretaceous lowstand systems that drained into the Western-Interior Seaway of North America (100s of cumecs). Paleodischarge of rivers can also be estimated independently by integrating estimates of drainage basin area and paleoclimate. These can be compared with paleodischarge estimates based on the river deposits themselves. The integration of paleodischarge estimates with more sophisticated provenance analysis should enable improved use of the sedimentary record to make estimates about the entire S2S system, as opposed to primarily the depositional component. A more quantitative approach to estimating the scale of sedimentary systems, and especially in the context of source areas, also puts constraints on the size and scale of potential hydrocarbon reservoirs and thus has economic value.

Volume 3 - Area Sources and Area Source Method Abstracts

EPA Pesticide Factsheets

Nonpoint (area) source emission reference materials from the EIIP. Provides nonpoint source guidance on planning, emissions estimation, data collection, inventory documentation and reporting, and quality assurance/quality control.

Domestic wells have high probability of pumping septic tank leachate

NASA Astrophysics Data System (ADS)

Bremer, J. E.; Harter, T.

2012-08-01

Onsite wastewater treatment systems are common in rural and semi-rural areas around the world; in the US, about 25-30% of households are served by a septic (onsite) wastewater treatment system, and many property owners also operate their own domestic well nearby. Site-specific conditions and local groundwater flow are often ignored when installing septic systems and wells. In areas with small lots (thus high spatial septic system densities), shallow domestic wells are prone to contamination by septic system leachate. Mass balance approaches have been used to determine a maximum septic system density that would prevent contamination of groundwater resources. In this study, a source area model based on detailed groundwater flow and transport modeling is applied for a stochastic analysis of domestic well contamination by septic leachate. Specifically, we determine the probability that a source area overlaps with a septic system drainfield as a function of aquifer properties, septic system density and drainfield size. We show that high spatial septic system density poses a high probability of pumping septic system leachate. The hydraulic conductivity of the aquifer has a strong influence on the intersection probability. We find that mass balance calculations applied on a regional scale underestimate the contamination risk of individual drinking water wells by septic systems. This is particularly relevant for contaminants released at high concentrations, for substances that experience limited attenuation, and those that are harmful even at low concentrations (e.g., pathogens).

Soil organic phosphorus flows to water via critical and non-critical hydrological source areas

NASA Astrophysics Data System (ADS)

Wang, Ying; Surridge, Ben; Haygarth, Phil

2015-04-01

Soil organic phosphorus flows to water via critical and non-critical hydrological source areas Ying Wang, Ben W.J. Surridge, Philip M. Haygarth Lancaster Environment Centre, Lancaster University, LA1 4YQ, UK Critical source areas (CSAs) are zones in the landscape where easily connected hydrology coincides with a phosphorus (P) sources in the soil. The P export risks in CSAs are hypothesised to be higher compared with non-critical source areas (Non-CSAs) and specifically that the magnitudes of P forms in CSA areas were higher than Non-CSAs. Past research on CSAs has often neglected forms of organic P, such as DNA and phospholipids which are among the most potentially biodegradable organic P compounds. The objectives of this study were i) to quantify the magnitude of organic P compounds in agricultural soils and specifically determine whether these magnitudes differed significantly between CSAs and Non-CSAs; ii) determine the variation of P magnitude between and within individual fields; iii) identify the P delivery concentrations in soil solution after raining events in CSAs. The study focussed on soils collected from the Morland sub-catchment of the River Eden catchment in Cumbria, northern England. CSA and Non-CSA pairs were identified using the SCIMAP modelling and field assessment providing five CSA - Non-CSA pairs in total. The results showed that there are significant differences in the total P (TP) concentrations, the proportions of DNA-P, WETP (water extractable total P), WERP (water extractable reactive P) and WEUP (water extractable unreactive P) between CSA and Non-CSA. We also found that the concentrations of all the P forms showed distribution variation between fields or even within the same field. Liable organic P such as DNA-P and PLD-P was presented considerable proportions of total P in soil, especially DNA-P which had a good correlation with TP. DNA-P in the ten areas accounted for a considerable proportion of soil TP (4.9 to 16.6%). Given the potential lability and bioavailability of DNA and phospholipids, our data demonstrate that these soil organic P could be a potential pool to support plant nutrition and a potential contributor to water pollution problems. Furthermore, For a number of soil samples, comparisons were made between extraction of P within phospholipids and DNA and the results of 31 PNMR analyses, to provide further characterisation of the organic P fractions within these soils.Data of this study will also be presented concerning the forms and magnitudes of P fractions in runoff pathways across an agricultural catchment, including the prevalence of organic P in these pathways. Keywords: Organic P; Soil; CSA; DNA; Phospholipids

Prevalence and Social Determinants of Type 2 Diabetes in a Coastal Area of Kerala, India.

PubMed

Aswathy, S; Lohidas, V; Paul, Nimitha; Anish, T S; Narayanan, Tinu; Oldenburg, Brian

2017-01-01

Varying prevalence rates of type 2 diabetes have been observed in different parts of the southern state of Kerala, India which is in an advanced stage of epidemiologic transition. Social patterning is evident in diabetes and therefore it was decided to undertake a study on estimating the prevalence of diabetes and associated social determinants. The adopted local self administration unit of the Medical College which is also the field practice area with a population of 25,096 was taken for the study. All the households in the area were visited and the details regarding self reported diabetes was collected after obtaining informed consent and analysis done by multivariate logistic regression. The prevalence of self reported diabetes in this coastal area was found to be low at 7.4%. Type 2 diabetes was also found to occur significantly earlier among the respondents belonging to the below poverty line. Age above 40 years (OR 2 95% CI 1.5-2.7, p=.000), marital status (OR 1.9 95% CI 1.1-2.1, p=.006) presence of comorbidities (OR 635 95% CI 389-969, p=.000), more than 8 years of schooling (OR 0.64 95% CI 0.46-0.86, p=.004), living conditions as represented by presence of household source of drinking water(OR 1.4 95% CI 1.01-1.5) were found to be independent predictors. Though there was increasing trend of diabetes among the forward caste line families after backward logistic regression this disappeared leaving behind the proxy of socioeconomic status, household source of drinking water. Though, the state of Kerala is in an advanced stage of epidemiologic transition, coastal areas are still in the earlier phases of transition with low prevalence of type 2 diabetes mellitus. Higher education and better living conditions are important social determinants of diabetes though further studies are necessary to delineate the impact of economic status and education.

Mineralogy and source rock evaluation of the marine Oligo-Miocene sediments in some wells in the Nile Delta and North Sinai, Egypt

NASA Astrophysics Data System (ADS)

El sheikh, Hassan; Faris, Mahmoud; Shaker, Fatma; Kumral, Mustafa

2016-06-01

This paper aims to study the mineralogical composition and determine the petroleum potential of source rocks of the Oligocene-Miocene sequence in the Nile Delta and North Sinai districts. The studied interval in the five wells can be divided into five rock units arranged from the top to base; Qawasim, Sidi Salem, Kareem, Rudeis, and Qantara formations. The bulk rock mineralogy of the samples was investigated using X-Ray Diffraction technique (XRD). The results showed that the sediments of the Nile Delta area are characterized by the abundance of quartz and kaolinite with subordinate amounts of feldspars, calcite, gypsum, dolomite, and muscovite. On the other hand, the data of the bulk rock analysis at the North Sinai wells showed that kaolinite, quartz, feldspar and calcite are the main constituents associated with minor amounts of dolomite, gypsum, mica, zeolite, and ankerite. Based on the organic geochemical investigations (TOC and Rock-Eval pyrolysis analyses), all studied formations in both areas are thermally immature but in the Nile delta area, Qawasim, Sidi Salem and Qantara formations (El-Temsah-2 Well) are organically-rich and have a good petroleum potential (kerogen Type II-oil-prone), while Rudeis Formation is a poor petroleum potential source rock (kerogen Type III-gas-prone). In the North Sinai area, Qantara Formation has a poor petroleum potential (kerogen Type III-gas-prone) and Sidi Salem Formation (Bardawil-1 Well) is a good petroleum potential source rock (kerogen Type II-oil-prone).

Western Tier Trichloroethylene Investigation Technical Plan. Version 3. 1

DTIC Science & Technology

1987-10-01

07p-o018.4 - 7’i.j -s 7,ze Ns vý-c~~f 0MB to.0 o,*%18 .. ý’ *. 4 -, I **5 1 "a! *- " -- .e..~’-!:c -~~ ’%as-ý9Ct, :C I. AUEENCY JSE ONLY .. eve DiarK...OBJECTIVES OF TASK 38 ARE TO: 1 . DETERMINE THE SOURCE(S) OF TRCLE IN THE WESTERN TIER 2. FOR EACH SOURCE, DEFINE THE CONTAMINANT PLUME 3. ESTIMATE THE...e. I TASK 38 TECHNICAL PLAN I TABLE OF CONTENTS i Sectio PA 1.0 INTRODUCTION 1 - 1 1 1.1 Background 1 - 1 1.2 Technical ADproach 1 -2 1.3 Areas to be

RACT (Reasonably Available Control Technology) determination for five industry categories in Florida

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hawks, R.L.; Schlesser, S.P.; Loudin, D.L.

Section 172(b)(2) of the Clean Air Act as amended August 1977, requires that SIP revisions 'provide for the implementation of all reasonably available control measures as expeditiously as practicable.' The use of RACT for stationary sources is defined as the lowest emission limit that a particular source is capable of meeting by the application of control technology that is reasonably available considering technological and economic feasibility. The purpose of this report has been to identify control techniques that best represent RACT for particular emission sources in TSP nonattainment areas in the State of Florida. These sources include phosphate process operations;more » portland cement plants; electric arc furnaces; sweat or pot furnaces; materials handling, sizing, screening, crushing, and grinding operations.« less

The SPES surface ionization source

NASA Astrophysics Data System (ADS)

Manzolaro, M.; D'Agostini, F.; Monetti, A.; Andrighetto, A.

2017-09-01

Ion sources and target systems play a crucial role in isotope separation on line facilities, determining the main characteristics of the radioactive ion beams available for experiments. In the context of the selective production of exotic species (SPES) facility, a 40 MeV, 200 μA proton beam directly impinges a uranium carbide target, generating approximately 1013 fissions per second. The radioactive isotopes produced by the 238U fissions are delivered to the 1+ ion source by means of a tubular transfer line. Here they can be ionized and subsequently accelerated toward the experimental areas. In this work, the characterization of the surface ionization source currently adopted for the SPES facility is presented, taking as a reference ionization efficiency and transversal emittance measurements. The effects of long term operation at high temperature are also illustrated and discussed.

Distribution, Source, and Ecological Risk Assessment of Polycyclic Aromatic Hydrocarbons in Surface Sediment of Liaodong Bay, Northeast China

NASA Astrophysics Data System (ADS)

Xu, Shuang; Tao, Ping; Li, Yuxia; Guo, Qi; Zhang, Yan; Wang, Man; Jia, Hongliang; Shao, Mihua

2018-01-01

Sixteen polycyclic aromatic hydrocarbons (PAHs) were determined in surface sediments from Liaodong Bay, northeast China. The concentration levels of total PAHs (Σ16PAHs) in sediment were 11.0˜249.6 ng·g-1 dry weight (dw), with a mean value of 89.9 ng·g-1 dry weight (dw). From the point of the spatial distribution, high PAHs levels were found in the western areas of Liaodong Bay. In the paper, sources of PAHs were investigated by diagnostic ratios, which indicated that pyrogenic sources were the main sources of PAHs in the sediment of Liaodong Bay. Therefore, selected PAH levels in sediments were compared with Sediments Quality Guidelines (ERM-ERL indexes) for evaluation probable toxic effects on marine organism.

Concentrations and forms of heavy metals around two ore processing sites in Katanga, Democratic Republic of Congo

NASA Astrophysics Data System (ADS)

Mees, F.; Masalehdani, M. N. N.; De Putter, T.; D'Hollander, C.; Van Biezen, E.; Mujinya, B. B.; Potdevin, J. L.; Van Ranst, E.

2013-01-01

The concentration of heavy metals and the forms in which they occur were determined for tailings and derived deposits of two major processing sites of Cu-Co and Cu-Zn-(Pb) ores in the Katanga Copperbelt (Kipushi, Likasi). They were studied by a combination of methods, focussed on the nature of water- and EDTA-extractable compounds, the mineralogical composition of tailings and associated secondary minerals, and textural features of metal-bearing efflorescences. For the Kipushi area, sulfide minerals in tailings of decantation basins are identified as the source of extractable metals they contain, but input from an external source rather than local oxidation of substrate components is responsible for high levels of contamination in the Likasi area. Contaminated areas around Likasi are characterized by an abundance of Mg-sulfate efflorescences with high concentrations of cobalt and other metals, acting as an important vector for further dispersion of contaminants by wind and water.

Sedimentary hydrocarbons and sterols in a South Atlantic estuarine/shallow continental shelf transitional environment under oil terminal and grain port influences.

PubMed

Bet, Rafael; Bícego, Marcia C; Martins, César C

2015-06-15

Sterols and hydrocarbons were determined in the surface sediments from the transitional environment between Paranaguá Bay and the shallow continental shelf in the South Atlantic to assess the sources of organic matter (OM) and the contamination status of an area exposed to multiple anthropogenic inputs. Total aliphatic hydrocarbon concentrations were less than 10μgg(-1), which is typical of unpolluted sediments, and related to recent inputs from higher terrestrial plants. Total polycyclic aromatic hydrocarbon ranged from

Integrated magnetic, gravity, and GPR surveys to locate the probable source of hydrocarbon contamination in Sharm El-Sheikh area, south Sinai, Egypt

NASA Astrophysics Data System (ADS)

Morsy, Mona; Rashed, Mohamed

2013-01-01

Sharm El-Sheikh waters were suddenly hit by hydrocarbon spills which created a serious threat to the prosperous tourism industry in and around the city. Analysis of soil samples, water samples, and seabed samples collected in and around the contaminated bay area showed anomalous levels of hydrocarbons. An integrated geophysical investigation, using magnetic, gravity, and ground penetrating radar geophysical tools, was conducted in the headland overlooking the contaminated bay in order to delineate the possible subsurface source of contamination. The results of the geophysical investigations revealed three underground manmade reinforced concrete tanks and a complicated network of buried steel pipes in addition to other unidentified buried objects. The depths and dimensions of the discovered objects were determined. Geophysical investigations also revealed the presence of a north-south oblique slip fault running through the eastern part of the studied area. Excavations, conducted later on, confirmed the presence of one of the tanks delineated by the geophysical surveys.

76 FR 13514 - National Emission Standards for Hazardous Air Pollutants for Chemical Manufacturing Area Sources

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-14

... National Emission Standards for Hazardous Air Pollutants for Chemical Manufacturing Area Sources AGENCY... Emission Standards for Hazardous Air Pollutants for Chemical Manufacturing Area Sources. Among the... Emission Standards for Hazardous Air Pollutants for Chemical Manufacturing Area Sources (CMAS) on October...

Topographic map analysis to determine Arjuno-Welirang volcanostratigraphy and implication for geothermal exploration

NASA Astrophysics Data System (ADS)

Apriani, Lestari; Satriana, Joshua; Aulian Chalik, Citra; Syahputra Mulyana, Reza; Hafidz, Muhammad; Suryantini

2017-12-01

Volcanostratigraphy study is used for supporting geothermal exploration on preliminary survey. This study is important to identify volcanic eruption center which shows potential area of geothermal heat source. The purpose of volcanostratigraphy study in research area is going to distinguish the characteristics of volcanic eruption product that construct the volcanic body. The analysis of Arjuno-Welirang volcanostratigraphy identification are based on topographic maps of Malang sheet with 1:100.000 scale, 1:50.000 scale, and a geological map. Regarding to the delineation of ridge and river, we determine five crowns, three hummocks, one brigade and one super brigade. The crowns consist of Ringgit, Welirang, Arjuno, Kawi, and Penanggungan, the hummocks comprise of Kembar III, Kembar II, and Kembar I, the brigade is Arjuno-Welirang, and the super brigade is Tengger. Based on topographic map interpretation and geothermal prospect evaluation method analysis, shows that Arjuno-Welirang prospect area have good geothermal resource potential.

Modeling and analysis of CSAMT field source effect and its characteristics

NASA Astrophysics Data System (ADS)

Da, Lei; Xiaoping, Wu; Qingyun, Di; Gang, Wang; Xiangrong, Lv; Ruo, Wang; Jun, Yang; Mingxin, Yue

2016-02-01

Controlled-source audio-frequency magnetotellurics (CSAMT) has been a highly successful geophysical tool used in a variety of geological exploration studies for many years. However, due to the artificial source used in the CSAMT technique, two important factors are considered during interpretation: non-plane-wave or geometric effects and source overprint effects. Hence, in this paper we simulate the source overprint effects and analyzed the rule and characteristics of its influence on CSAMT applications. Two-dimensional modeling was carried out using an adaptive unstructured finite element method to simulate several typical models. Also, we summarized the characteristics and rule of the source overprint effects and analyzed its influence on the data taken over several mining areas. The results obtained from the study shows that the occurrence and strength of the source overprint effect is dependent on the location of the source dipole, in relation to the receiver and the subsurface geology. In order to avoid source overprint effects, three principle were suggested to determine the best location for the grounded dipole source in the field.

Utility of linking primary care electronic medical records with Canadian census data to study the determinants of chronic disease: an example based on socioeconomic status and obesity.

PubMed

Biro, Suzanne; Williamson, Tyler; Leggett, Jannet Ann; Barber, David; Morkem, Rachael; Moore, Kieran; Belanger, Paul; Mosley, Brian; Janssen, Ian

2016-03-11

Electronic medical records (EMRs) used in primary care contain a breadth of data that can be used in public health research. Patient data from EMRs could be linked with other data sources, such as a postal code linkage with Census data, to obtain additional information on environmental determinants of health. While promising, successful linkages between primary care EMRs with geographic measures is limited due to ethics review board concerns. This study tested the feasibility of extracting full postal code from primary care EMRs and linking this with area-level measures of the environment to demonstrate how such a linkage could be used to examine the determinants of disease. The association between obesity and area-level deprivation was used as an example to illustrate inequalities of obesity in adults. The analysis included EMRs of 7153 patients aged 20 years and older who visited a single, primary care site in 2011. Extracted patient information included demographics (date of birth, sex, postal code) and weight status (height, weight). Information extraction and management procedures were designed to mitigate the risk of individual re-identification when extracting full postal code from source EMRs. Based on patients' postal codes, area-based deprivation indexes were created using the smallest area unit used in Canadian censuses. Descriptive statistics and socioeconomic disparity summary measures of linked census and adult patients were calculated. The data extraction of full postal code met technological requirements for rendering health information extracted from local EMRs into anonymized data. The prevalence of obesity was 31.6 %. There was variation of obesity between deprivation quintiles; adults in the most deprived areas were 35 % more likely to be obese compared with adults in the least deprived areas (Chi-Square = 20.24(1), p < 0.0001). Maps depicting spatial representation of regional deprivation and obesity were created to highlight high risk areas. An area based socio-economic measure was linked with EMR-derived objective measures of height and weight to show a positive association between area-level deprivation and obesity. The linked dataset demonstrates a promising model for assessing health disparities and ecological factors associated with the development of chronic diseases with far reaching implications for informing public health and primary health care interventions and services.

Stanols as a tool to track the origin of microbial contamination of oysters, Crassostrea gigas, in shellfish areas.

NASA Astrophysics Data System (ADS)

Harrault, Loïc; Jardé, Emilie; Jeanneau, Laurent; Petitjean, Patrice

2013-04-01

Runoff of cattle manures (cows, pigs, sheeps) or discharge of effluent from wastewater treatment plants (WWTP) into aquatic ecosystems can lead to microbiological contamination of waters and living organisms. In coastal ecosystems and particularly in shellfish harvesting areas, the presence of pathogen microorganisms in waters induces fecal contamination of filter feeding bivalves (oysters, mussels, scallops…), therefore leading to human health risks associated to the consumption of these contaminated organisms. Watershed management plans that aim at limiting these risks require the development of tools able to identify fecal contamination sources. The fecal indicator bacteria used in the regulations to determine fecal contamination are not source specific since they are found in the feces of most warm-blooded animals. Thus, microbiological biomarkers have been developed in association with chemical biomarkers as Microbial Source Tracking (MST) methods. Fecal stanols, by-products of sterols obtained by human and animal microbial gut flora, are found in considerable amounts in feces with different relative proportions depending on their animal or human source. Recently, in association with microbiological biomarkers, the stanol fingerprint of contaminated waters has been successfully used to determine the main source of fecal contamination (cow, pig or human sources) in rural watersheds (Brittany, France). Up to now, the use of the stanol fingerprint to track the fecal contamination in shellfish tissues, especially bivalves, has been limited to the analysis of coprostanol, a stanol commonly associated to human contamination. Therefore, whether the stanol fingerprint can be used as a MST method in bivalves or not is still unknown. The first aim of this study was to compare several organic extraction procedures of stanols in the oyster Crassostrea gigas to determine a reliable method for stanol fingerprint analysis in bivalves. Solvent extraction and purification steps have been carried out with attention as they are critical for stanol quantification. Secondly, the evolution of the stanol fingerprint of oysters with time was evaluated during 6 days by artificially contaminating microcosms with two concentrations of a WWTP effluent. In the microcosms, the fingerprint of stanols as a chemical biomarkers of fecal (human) contamination was compared to counts of Escherichia coli, a commonly used microbial indicator. In association with microbial markers, the method developed from the two previous steps will be applied at the watershed scale in order to identify sources of fecal contamination in Brittany and Normandy (France).

Hydrogeochemical investigation to understand nitrate movement in groundwater of volcanic island, Korea

NASA Astrophysics Data System (ADS)

Kwon, E. H.; Park, J.; Chung, E.; Kang, B. R.; Park, W. B.; Woo, N. C.

2017-12-01

Groundwater is the sole-source of water supply in the volcanic island, Jeju-do, Korea. Since early 1990s, the nitrate contamination of groundwater has increased especially in the western part of the island. High level of nitrate in water can cause not only health risk to human body but also environmental side effect such as eutrophication and algal bloom in the coastal area. Several studies have done to estimate nitrate contamination in groundwater of local areas, but none of them dealt with nitrate movement with flow paths. So, this study aimed to determine the source and migration of nitrate in groundwater in the Gosan area, located in the western part of Jeju island through seasonal monitoring of hydrogeochemistry and stable isotope analyses from pumping and monitoring wells. Water samples including rainfall and groundwater are measured for major ions (Ca, Na, K, Mg, SO4, HCO3, NO3, Cl, etc.) and stable isotopes (i.e., δ2H, δ18O, δ18O-NO3, δ15N-NO3). From the monitoring data, we could evaluate hydrochemical change during nitrate contamination, and also could identify that groundwater in Gosan area is recharged mainly by regional flow from the high-altitude region. In future study, we will conduct additional seasonal monitoring from the multi-depth monitoring wells and will use statistical analysis to understand pollution sources and paths specifically.

Seismic noise frequency dependent P and S wave sources

NASA Astrophysics Data System (ADS)

Stutzmann, E.; Schimmel, M.; Gualtieri, L.; Farra, V.; Ardhuin, F.

2013-12-01

Seismic noise in the period band 3-10 sec is generated in the oceans by the interaction of ocean waves. Noise signal is dominated by Rayleigh waves but body waves can be extracted using a beamforming approach. We select the TAPAS array deployed in South Spain between June 2008 and September 2009 and we use the vertical and horizontal components to extract noise P and S waves, respectively. Data are filtered in narrow frequency bands and we select beam azimuths and slownesses that correspond to the largest continuous sources per day. Our procedure automatically discard earthquakes which are localized during short time durations. Using this approach, we detect many more noise P-waves than S-waves. Source locations are determined by back-projecting the detected slowness/azimuth. P and S waves are generated in nearby areas and both source locations are frequency dependent. Long period sources are dominantly in the South Atlantic and Indian Ocean whereas shorter period sources are rather in the North Atlantic Ocean. We further show that the detected S-waves are dominantly Sv-waves. We model the observed body waves using an ocean wave model that takes into account all possible wave interactions including coastal reflection. We use the wave model to separate direct and multiply reflected phases for P and S waves respectively. We show that in the South Atlantic the complex source pattern can be explained by the existence of both coastal and pelagic sources whereas in the North Atlantic most body wave sources are pelagic. For each detected source, we determine the equivalent source magnitude which is compared to the model.

Quantitative analysis of trace levels of surface contamination by X-ray photoelectron spectroscopy Part I: statistical uncertainty near the detection limit.

PubMed

Hill, Shannon B; Faradzhev, Nadir S; Powell, Cedric J

2017-12-01

We discuss the problem of quantifying common sources of statistical uncertainties for analyses of trace levels of surface contamination using X-ray photoelectron spectroscopy. We examine the propagation of error for peak-area measurements using common forms of linear and polynomial background subtraction including the correlation of points used to determine both background and peak areas. This correlation has been neglected in previous analyses, but we show that it contributes significantly to the peak-area uncertainty near the detection limit. We introduce the concept of relative background subtraction variance (RBSV) which quantifies the uncertainty introduced by the method of background determination relative to the uncertainty of the background area itself. The uncertainties of the peak area and atomic concentration and of the detection limit are expressed using the RBSV, which separates the contributions from the acquisition parameters, the background-determination method, and the properties of the measured spectrum. These results are then combined to find acquisition strategies that minimize the total measurement time needed to achieve a desired detection limit or atomic-percentage uncertainty for a particular trace element. Minimization of data-acquisition time is important for samples that are sensitive to x-ray dose and also for laboratories that need to optimize throughput.

Radioisotope measurement of selected parameters of liquid-gas flow using single detector system

NASA Astrophysics Data System (ADS)

Zych, Marcin; Hanus, Robert; Jaszczur, Marek; Mosorov, Volodymyr; Świsulski, Dariusz

2018-06-01

To determine the parameters of two-phase flows using radioisotopes, usually two detectors are used. Knowing the distance between them, the velocity of the dispersed phase is calculated based on time delay estimation. Such a measurement system requires the use of two gamma-ray sealed sources. But in some situations it is also possible to determine velocity of dispersed phase using only one scintillation probe and one gamma-ray source. However, this requires proper signal analysis and prior calibration. This may also cause larger measurement errors. On the other hand, it allows measurements in hard to reach areas where there is often no place for the second detector. Additionally, by performing a previous calibration, it is possible to determine the void fraction or concentration of the selected phase. In this work an autocorrelation function was used to analyze the signal from the scintillation detector, which allowed for the determination of air velocities in slug and plug flows with an accuracy of 8.5%. Based on the analysis of the same signal, a void fraction with error of 15% was determined.

Validating and updating a prediction rule for serious bacterial infection in patients with fever without source.

PubMed

Bleeker, S E; Derksen-Lubsen, G; Grobbee, D E; Donders, A R T; Moons, K G M; Moll, H A

2007-01-01

To externally validate and update a previously developed rule for predicting the presence of serious bacterial infections in children with fever without apparent source. Patients, 1-36 mo, presenting with fever without source, were prospectively enrolled. Serious bacterial infection included bacterial meningitis, sepsis, bacteraemia, pneumonia, urinary tract infection, bacterial gastroenteritis, osteomyelitis/ethmoiditis. The generalizability of the original rule was determined. Subsequently, the prediction rule was updated using all available data of the patients with fever without source (1996-1998 and 2000-2001, n = 381) using multivariable logistic regression. the generalizability of the rule appeared insufficient in the new patients (n = 150). In the updated rule, independent predictors from history and examination were duration of fever, vomiting, ill clinical appearance, chest-wall retractions and poor peripheral circulation (ROC area (95%CI): 0.69 (0.63-0.75)). Additional independent predictors from laboratory were serum white blood cell count and C-reactive protein, and in urinalysis > or = 70 white bloods (ROC area (95%CI): 0.83 (0.78-0.88). A previously developed prediction rule for predicting the presence of serious bacterial infection in children with fever without apparent source was updated. Its clinical score can be used as a first screening tool. Additional laboratory testing may specify the individual risk estimate (range: 4-54%) further.

Comparison of the air pollution biomonitoring ability of three Tillandsia species and the lichen Ramalina celastri in Argentina.

PubMed

Bermudez, Gonzalo M A; Rodriguez, Judith H; Pignata, María L

2009-01-01

Bioaccumulation ability and response to air pollution sources were evaluated for Tillandsia capillaris Ruíz and Pav. f. capillaris, T. recurvata L., T. tricholepis Baker and the lichen Ramalina celastri (Spreng.) Krog. and Swinsc. Epiphyte samples collected from a non contaminated area in the province of Córdoba were transplanted to a control site and three areas categorised according to agricultural, urban and industrial (metallurgical and metal-mechanical) emission sources. Bioindicators were exposed for 3-, 6- and 9-month periods. A foliar damage index was established for Tillandsia and a pollution index for the lichen, and S, Fe, Mn and Zn concentrations were determined. An order of efficiency for the species and conditions studied is proposed taking into account heavy metal accumulation: T. recurvata >T. tricholepis >R. celastri >T. capillaris. All species studied showed Mn to be related to agricultural activity and Fe to industries and soil particles, and Zn was related to urban and industrial sources. As far as physiological response is concerned, T. tricholepis and T. capillaris were more sensitive to agricultural activities, whereas T. recurvata was sensitive to urban and industrial sources, and only partially to agricultural sources. No relationship was found for R. celastri.

Independent component analysis of EEG dipole source localization in resting and action state of brain

NASA Astrophysics Data System (ADS)

Almurshedi, Ahmed; Ismail, Abd Khamim

2015-04-01

EEG source localization was studied in order to determine the location of the brain sources that are responsible for the measured potentials at the scalp electrodes using EEGLAB with Independent Component Analysis (ICA) algorithm. Neuron source locations are responsible in generating current dipoles in different states of brain through the measured potentials. The current dipole sources localization are measured by fitting an equivalent current dipole model using a non-linear optimization technique with the implementation of standardized boundary element head model. To fit dipole models to ICA components in an EEGLAB dataset, ICA decomposition is performed and appropriate components to be fitted are selected. The topographical scalp distributions of delta, theta, alpha, and beta power spectrum and cross coherence of EEG signals are observed. In close eyes condition it shows that during resting and action states of brain, alpha band was activated from occipital (O1, O2) and partial (P3, P4) area. Therefore, parieto-occipital area of brain are active in both resting and action state of brain. However cross coherence tells that there is more coherence between right and left hemisphere in action state of brain than that in the resting state. The preliminary result indicates that these potentials arise from the same generators in the brain.

Aircraft Observations of Nitrous Oxide (N2O) in the San Joaquin Valley of California

NASA Astrophysics Data System (ADS)

Muto, S.; Herrera, S.; Pusede, S.

2017-12-01

Agriculture is the largest source of anthropogenic nitrous oxide (N2O) in the U.S. While it is generally known which processes produce N2O, there is considerable uncertainty in controls over N2O emissions. Factors that determine N2O fluxes, such as soil properties and manure management, are highly variable in space and time, and, as a result, it has proven difficult to upscale chamber-derived soil flux measurements to regional spatial scales. Aircraft observations provide a regional picture of the N2O spatial distribution, but, because N2O is very long-lived, it is challenging to attribute measured concentrations of N2O to distinct local sources, especially over areas with complex and integrated land use. This study takes advantage of a novel aircraft N2O dataset collected onboard the low-flying, slow-moving NASA C-23 Sherpa in the San Joaquin Valley (SJV) of California, a region with a variety of N2O sources, including dairies, feedlots, fertilized cropland, and industrial facilities. With these measurements, we link observed N2O enhancements to specific sources at sub-inventory spatial scales. We compare our results with area-weighted emission profiles obtained by integrating detailed emission inventory data, agricultural statistics, and GIS source mapping.

Identifying (subsurface) anthropogenic heat sources that influence temperature in the drinking water distribution system

NASA Astrophysics Data System (ADS)

Agudelo-Vera, Claudia M.; Blokker, Mirjam; de Kater, Henk; Lafort, Rob

2017-09-01

The water temperature in the drinking water distribution system and at customers' taps approaches the surrounding soil temperature at a depth of 1 m. Water temperature is an important determinant of water quality. In the Netherlands drinking water is distributed without additional residual disinfectant and the temperature of drinking water at customers' taps is not allowed to exceed 25 °C. In recent decades, the urban (sub)surface has been getting more occupied by various types of infrastructures, and some of these can be heat sources. Only recently have the anthropogenic sources and their influence on the underground been studied on coarse spatial scales. Little is known about the urban shallow underground heat profile on small spatial scales, of the order of 10 m × 10 m. Routine water quality samples at the tap in urban areas have shown up locations - so-called hotspots - in the city, with relatively high soil temperatures - up to 7 °C warmer - compared to the soil temperatures in the surrounding rural areas. Yet the sources and the locations of these hotspots have not been identified. It is expected that with climate change during a warm summer the soil temperature in the hotspots can be above 25 °C. The objective of this paper is to find a method to identify heat sources and urban characteristics that locally influence the soil temperature. The proposed method combines mapping of urban anthropogenic heat sources, retrospective modelling of the soil temperature, analysis of water temperature measurements at the tap, and extensive soil temperature measurements. This approach provided insight into the typical range of the variation of the urban soil temperature, and it is a first step to identifying areas with potential underground heat stress towards thermal underground management in cities.

Wet nitrogen deposition across the urban-intensive agricultural-rural transect of a small urban area in southwest China.

PubMed

Deng, Ouping; Zhang, Shirong; Deng, Liangji; Zhang, Chunlong; Fei, Jianbo

2018-03-01

Understanding of the spatial and temporal variation of the flux of atmospheric nitrogen (N) deposition is essential for assessment of its impact on ecosystems. However, little attention has been paid to the variability of N deposition across urban-intensive agricultural-rural transects. A continuous 2-year observational study (from January 2015 to December 2016) was conducted to determine wet N deposition across the urban-intensive agricultural-rural transect of a small urban area in southwest China. Significantly spatial and temporal variations were found in the research area. Along the urban-intensive agricultural-rural transect, the TN and NH 4 + -N deposition first increased and then decreased, and the NO 3 - -N and dissolved organic N (DON) deposition decreased continuously. Wet N deposition was mainly affected by the districts of agro-facilities, roads and build up lands. Wet NH 4 + -N deposition had non-seasonal emission sources including industrial emissions and urban excretory wastes in urban districts and seasonal emission sources such as fertilizer and manure volatilization in the other districts. However, wet NO 3 - -N deposition had seasonal emission sources such as industrial emissions and fireworks in urban district and non-seasonal emission sources such as transportation in the other districts. Deposition of DON was likely to have had similar sources to NO 3 - -N deposition in rural district, and high-temperature-dependent sources in urban and intensive agricultural districts. Considering the annual wet TN deposition in the intensive agricultural district was about 11.1% of the annual N fertilizer input, N fertilizer rates of crops should be reduced in this region to avoid the excessive application, and the risk of N emissions to the environment.

A cautionary tale: A study of a methane enhancement over the North Sea

NASA Astrophysics Data System (ADS)

Cain, M.; Warwick, N. J.; Fisher, R. E.; Lowry, D.; Lanoisellé, M.; Nisbet, E. G.; France, J.; Pitt, J.; O'Shea, S.; Bower, K. N.; Allen, G.; Illingworth, S.; Manning, A. J.; Bauguitte, S.; Pisso, I.; Pyle, J. A.

2017-07-01

Airborne measurements of a methane (CH4) plume over the North Sea from August 2013 are analyzed. The plume was only observed downwind of circumnavigated gas fields, and three methods are used to determine its source. First, a mass balance calculation assuming a gas field source gives a CH4 emission rate between 2.5 ± 0.8×104 and 4.6 ± 1.5×104 kg h-1. This would be greater than the industry's reported 0.5% leak rate if it were emitting for more than half the time. Second, annual average UK CH4 emissions are combined with an atmospheric dispersion model to create pseudo-observations. Clean air from the North Atlantic passed over mainland UK, picking up anthropogenic emissions. To best explain the observed plume using pseudo-observations, an additional North Sea source from the gas rigs area is added. Third, the δ13C-CH4 from the plume is shown to be -53‰, which is lighter than fossil gas but heavier than the UK average emission. We conclude that either an additional small-area mainland source is needed, combined with temporal variability in emission or transport in small-scale meteorological features. Alternatively, a combination of additional sources that are at least 75% from the mainland (-58‰) and up to 25% from the North Sea gas rigs area (-32‰) would explain the measurements. Had the isotopic analysis not been performed, the likely conclusion would have been of a gas field source of CH4. This demonstrates the limitation of analyzing mole fractions alone, as the simplest explanation is rejected based on analysis of isotopic data.

A boundary element approach to optimization of active noise control sources on three-dimensional structures

NASA Technical Reports Server (NTRS)

Cunefare, K. A.; Koopmann, G. H.

1991-01-01

This paper presents the theoretical development of an approach to active noise control (ANC) applicable to three-dimensional radiators. The active noise control technique, termed ANC Optimization Analysis, is based on minimizing the total radiated power by adding secondary acoustic sources on the primary noise source. ANC Optimization Analysis determines the optimum magnitude and phase at which to drive the secondary control sources in order to achieve the best possible reduction in the total radiated power from the noise source/control source combination. For example, ANC Optimization Analysis predicts a 20 dB reduction in the total power radiated from a sphere of radius at a dimensionless wavenumber ka of 0.125, for a single control source representing 2.5 percent of the total area of the sphere. ANC Optimization Analysis is based on a boundary element formulation of the Helmholtz Integral Equation, and thus, the optimization analysis applies to a single frequency, while multiple frequencies can be treated through repeated analyses.

Source apportionments of PM2.5 organic carbon during the elevated pollution episodes in the Ordos region, Inner Mongolia, China.

PubMed

Khuzestani, Reza Bashiri; Schauer, James J; Shang, Jing; Cai, Tianqi; Fang, Dongqing; Wei, Yongjie; Zhang, Lulu; Zhang, Yuanxun

2018-05-01

The Ordos region in the southwestern part of Inner Mongolia experiences frequent PM concentrations in excess of the national PM 2.5 air quality standards. In order to determine the key sources of PM 2.5 contributing to these pollution episodes, the main sources of PM 2.5 OC during elevated PM episodes in the Inner Mongolia were analyzed and compared with non-polluted days. This will provide insight to the main sources of particulate matter pollution during the high-pollution episodes and the effective seasonal strategies to control sources of particulate matter during months and with the highest PM concentrations that need to be controlled. The PMF source contributions to OC demonstrated that the industrial/coal combustion (4762.77 ± 1061.54 versus 2726.49 ± 469.75 ng/m 3 ; p < 0.001) and mobile source factors (4651.14 ± 681.82 versus 2605.55 ± 276.50 ng/m 3 ; p value < 0.001) showed greater contributions to the elevated concentrations during the episode. The spatial analysis of secondary organic carbon (SOC) factors, regional biomass burning, and biogenic sources did not show significant difference in the pollution episodes and the non-polluted months. In addition, the bivariate polar plots and CWT maps of the industrial/coal combustion and mobile illustrated a regional long-range transport patterns from the external sources to the study area, however, adjacent areas were mostly controlling the contributions of these factors during the PM elevated episodes. The SOC sources, regional biomass burning, and biogenic sources illustrated a regional long-range transport with similar locations found during the elevated pollution episodes compared to the normal situations.

Parasite sources and sinks in a patched Ross-Macdonald malaria model with human and mosquito movement: Implications for control.

PubMed

Ruktanonchai, Nick W; Smith, David L; De Leenheer, Patrick

2016-09-01

We consider the dynamics of a mosquito-transmitted pathogen in a multi-patch Ross-Macdonald malaria model with mobile human hosts, mobile vectors, and a heterogeneous environment. We show the existence of a globally stable steady state, and a threshold that determines whether a pathogen is either absent from all patches, or endemic and present at some level in all patches. Each patch is characterized by a local basic reproduction number, whose value predicts whether the disease is cleared or not when the patch is isolated: patches are known as "demographic sinks" if they have a local basic reproduction number less than one, and hence would clear the disease if isolated; patches with a basic reproduction number above one would sustain endemic infection in isolation, and become "demographic sources" of parasites when connected to other patches. Sources are also considered focal areas of transmission for the larger landscape, as they export excess parasites to other areas and can sustain parasite populations. We show how to determine the various basic reproduction numbers from steady state estimates in the patched network and knowledge of additional model parameters, hereby identifying parasite sources in the process. This is useful in the context of control of the infection on natural landscapes, because a commonly suggested strategy is to target focal areas, in order to make their corresponding basic reproduction numbers less than one, effectively turning them into sinks. We show that this is indeed a successful control strategy-albeit a conservative and possibly expensive one-in case either the human host, or the vector does not move. However, we also show that when both humans and vectors move, this strategy may fail, depending on the specific movement patterns exhibited by hosts and vectors. Copyright © 2016 Elsevier Inc. All rights reserved.

Source origin of trace elements in PM from regional background, urban and industrial sites of Spain

NASA Astrophysics Data System (ADS)

Querol, X.; Viana, M.; Alastuey, A.; Amato, F.; Moreno, T.; Castillo, S.; Pey, J.; de la Rosa, J.; Sánchez de la Campa, A.; Artíñano, B.; Salvador, P.; García Dos Santos, S.; Fernández-Patier, R.; Moreno-Grau, S.; Negral, L.; Minguillón, M. C.; Monfort, E.; Gil, J. I.; Inza, A.; Ortega, L. A.; Santamaría, J. M.; Zabalza, J.

Despite their significant role in source apportionment analysis, studies dedicated to the identification of tracer elements of emission sources of atmospheric particulate matter based on air quality data are relatively scarce. The studies describing tracer elements of specific sources currently available in the literature mostly focus on emissions from traffic or large-scale combustion processes (e.g. power plants), but not on specific industrial processes. Furthermore, marker elements are not usually determined at receptor sites, but during emission. In our study, trace element concentrations in PM 10 and PM 2.5 were determined at 33 monitoring stations in Spain throughout the period 1995-2006. Industrial emissions from different forms of metallurgy (steel, stainless steel, copper, zinc), ceramic and petrochemical industries were evaluated. Results obtained at sites with no significant industrial development allowed us to define usual concentration ranges for a number of trace elements in rural and urban background environments. At industrial and traffic hotspots, average trace metal concentrations were highest, exceeding rural background levels by even one order of magnitude in the cases of Cr, Mn, Cu, Zn, As, Sn, W, V, Ni, Cs and Pb. Steel production emissions were linked to high levels of Cr, Mn, Ni, Zn, Mo, Cd, Se and Sn (and probably Pb). Copper metallurgy areas showed high levels of As, Bi, Ga and Cu. Zinc metallurgy was characterised by high levels of Zn and Cd. Glazed ceramic production areas were linked to high levels of Zn, As, Se, Zr, Cs, Tl, Li, Co and Pb. High levels of Ni and V (in association) were tracers of petrochemical plants and/or fuel-oil combustion. At one site under the influence of heavy vessel traffic these elements could be considered tracers (although not exclusively) of shipping emissions. Levels of Zn-Ba and Cu-Sb were relatively high in urban areas when compared with industrialised regions due to tyre and brake abrasion, respectively.

Sources and transport of phosphorus to rivers in California and adjacent states, U.S., as determined by SPARROW modeling

USGS Publications Warehouse

Domagalski, Joseph L.; Saleh, Dina

2015-01-01

The SPARROW (SPAtially Referenced Regression on Watershed attributes) model was used to simulate annual phosphorus loads and concentrations in unmonitored stream reaches in California, U.S., and portions of Nevada and Oregon. The model was calibrated using de-trended streamflow and phosphorus concentration data at 80 locations. The model explained 91% of the variability in loads and 51% of the variability in yields for a base year of 2002. Point sources, geological background, and cultivated land were significant sources. Variables used to explain delivery of phosphorus from land to water were precipitation and soil clay content. Aquatic loss of phosphorus was significant in streams of all sizes, with the greatest decay predicted in small- and intermediate-sized streams. Geological sources, including volcanic rocks and shales, were the principal control on concentrations and loads in many regions. Some localized formations such as the Monterey shale of southern California are important sources of phosphorus and may contribute to elevated stream concentrations. Many of the larger point source facilities were located in downstream areas, near the ocean, and do not affect inland streams except for a few locations. Large areas of cultivated land result in phosphorus load increases, but do not necessarily increase the loads above those of geological background in some cases because of local hydrology, which limits the potential of phosphorus transport from land to streams.

Characterization of alluvial dust sources and their temporal development - a multi-sensor approach for the Aïr Massif, Niger

NASA Astrophysics Data System (ADS)

Feuerstein, Stefanie; Schepanski, Kerstin

2017-04-01

One of the world's largest sources of atmospheric dust is the Sahara. It is said that 55% of the total global dust emission can be linked to the desert in northern Africa. Thus, understanding the Saharan dust sources is of great importance to estimate the total global dust load and its variability. Especially one type of dust sources has gained attention in dust research in recent years: The emission of dust from sediments formed by hydrologic processes, so called alluvial dust sources. These sediments were either formed in the past under the influences of a more humid paleoclimate or are deposited recently, e.g. during strong precipitation events when surficial runoff leads to the activation of wadi systems or to the occurrence of flash floods. Especially the latter phenomenon is able to deliver a huge amount of potentially erodible sediments. The research presented here focuses on the characterization of these alluvial dust sources with special attention on their temporal variability in relation to wet and dry phases. A study area covering the Aïr Massif in Niger is analysed over a four years time span from January 2013 to December 2016. The whole cycle from sediment formation to dust emission is illustrated by using data of various satellite sensors that are able to capture the processes taking place at the land surface as well as in the atmosphere: (1) The rainfall distribution for the study area is shown by time series of the TRMM precipitation estimates. A catchment analysis of the area helps to estimate the amount of surficial runoff and to detect areas of potential sediment accumulation. (2) Changes in the sediment structure of the land surface are analysed using atmospherically corrected time series of NASA's Landsat-8 OLI satellite. A land cover classification shows the distribution of alluvial sediments over the area; fresh layers of alluvial deposits are detected. Furthermore, the evolution of the vegetation cover, which inhibits dust emission, is analysed by calculating NDVI time series from the Landsat data. (3) The MSG Dust Product is used to determine the frequency of dust emission from the investigation area. Furthermore, the product allows the precise localization of the sources. Therefore the alluvial sediments can directly be connected to dust emission. By combining the findings of these different satellite sensors, a profound analysis of alluvial dust sources on different levels is possible. The connection between the amount of precipitation and the supply of potentially erodible sediments is shown, which leads to a better understanding of the temporal evolution and importance of this source type.

Mathematical modeling of systemic factors determining the risk of deterioration of drinking water supply and development of allergic diseases of population

NASA Astrophysics Data System (ADS)

Bespalov, Yurii G.; Nosov, Konstantin V.; Vysotska, Olena V.; Porvan, Andrii P.; Omiotek, Zbigniew; Burlibay, Aron; Assembay, Azat; Szatkowska, Małgorzata

2017-08-01

This study aims at mathematical modeling of systemic factors threatening the sanitary and hygienic state of sources of water supply. It is well-known, that this state affects health of population consuming water from different water sources (lakes, reservoirs, rivers). In particular, water quality problem may cause allergic reactions that are the important problem of health care. In the paper, the authors present the mathematical model, that enables on the basis of observations of a natural system to predict the system's behavior and determine the risks related to deterioration of drinking water resources. As a case study, we uses supply of drinking water from Lake Sevan, but the approach developed in the study can be applied to wide area of adjacent problems.

Establishment of turbidity forecasting model and early-warning system for source water turbidity management using back-propagation artificial neural network algorithm and probability analysis.

PubMed

Yang, Tsung-Ming; Fan, Shu-Kai; Fan, Chihhao; Hsu, Nien-Sheng

2014-08-01

The purpose of this study is to establish a turbidity forecasting model as well as an early-warning system for turbidity management using rainfall records as the input variables. The Taipei Water Source Domain was employed as the study area, and ANOVA analysis showed that the accumulative rainfall records of 1-day Ping-lin, 2-day Ping-lin, 2-day Fei-tsui, 2-day Shi-san-gu, 2-day Tai-pin and 2-day Tong-hou were the six most significant parameters for downstream turbidity development. The artificial neural network model was developed and proven capable of predicting the turbidity concentration in the investigated catchment downstream area. The observed and model-calculated turbidity data were applied to developing the turbidity early-warning system. Using a previously determined turbidity as the threshold, the rainfall criterion, above which the downstream turbidity would possibly exceed this respective threshold turbidity, for the investigated rain gauge stations was determined. An exemplary illustration demonstrated the effectiveness of the proposed turbidity early-warning system as a precautionary alarm of possible significant increase of downstream turbidity. This study is the first report of the establishment of the turbidity early-warning system. Hopefully, this system can be applied to source water turbidity forecasting during storm events and provide a useful reference for subsequent adjustment of drinking water treatment operation.

Molecular inference of sources and spreading patterns of Plasmodium falciparum malaria parasites in internally displaced persons settlements in Myanmar-China border area.

PubMed

Lo, Eugenia; Zhou, Guofa; Oo, Winny; Lee, Ming-Chieh; Baum, Elisabeth; Felgner, Philip L; Yang, Zhaoqing; Cui, Liwang; Yan, Guiyun

2015-07-01

In Myanmar, civil unrest and establishment of internally displaced persons (IDP) settlement along the Myanmar-China border have impacted malaria transmission. The growing IDP populations raise deep concerns about health impact on local communities. Microsatellite markers were used to examine the source and spreading patterns of Plasmodium falciparum between IDP settlement and surrounding villages in Myanmar along the China border. Genotypic structure of P. falciparum was compared over the past three years from the same area and the demographic history was inferred to determine the source of recent infections. In addition, we examined if border migration is a factor of P. falciparum infections in China by determining gene flow patterns across borders. Compared to local community, the IDP samples showed a reduced and consistently lower genetic diversity over the past three years. A strong signature of genetic bottleneck was detected in the IDP samples. P. falciparum infections from the border regions in China were genetically similar to Myanmar and parasite gene flow was not constrained by geographical distance. Reduced genetic diversity of P. falciparum suggested intense malaria control within the IDP settlement. Human movement was a key factor to the spread of malaria both locally in Myanmar and across the international border. Copyright © 2015 Elsevier B.V. All rights reserved.

Estimated Accuracy of Three Common Trajectory Statistical Methods

NASA Technical Reports Server (NTRS)

Kabashnikov, Vitaliy P.; Chaikovsky, Anatoli P.; Kucsera, Tom L.; Metelskaya, Natalia S.

2011-01-01

Three well-known trajectory statistical methods (TSMs), namely concentration field (CF), concentration weighted trajectory (CWT), and potential source contribution function (PSCF) methods were tested using known sources and artificially generated data sets to determine the ability of TSMs to reproduce spatial distribution of the sources. In the works by other authors, the accuracy of the trajectory statistical methods was estimated for particular species and at specified receptor locations. We have obtained a more general statistical estimation of the accuracy of source reconstruction and have found optimum conditions to reconstruct source distributions of atmospheric trace substances. Only virtual pollutants of the primary type were considered. In real world experiments, TSMs are intended for application to a priori unknown sources. Therefore, the accuracy of TSMs has to be tested with all possible spatial distributions of sources. An ensemble of geographical distributions of virtual sources was generated. Spearman s rank order correlation coefficient between spatial distributions of the known virtual and the reconstructed sources was taken to be a quantitative measure of the accuracy. Statistical estimates of the mean correlation coefficient and a range of the most probable values of correlation coefficients were obtained. All the TSMs that were considered here showed similar close results. The maximum of the ratio of the mean correlation to the width of the correlation interval containing the most probable correlation values determines the optimum conditions for reconstruction. An optimal geographical domain roughly coincides with the area supplying most of the substance to the receptor. The optimal domain s size is dependent on the substance decay time. Under optimum reconstruction conditions, the mean correlation coefficients can reach 0.70 0.75. The boundaries of the interval with the most probable correlation values are 0.6 0.9 for the decay time of 240 h and 0.5 0.95 for the decay time of 12 h. The best results of source reconstruction can be expected for the trace substances with a decay time on the order of several days. Although the methods considered in this paper do not guarantee high accuracy they are computationally simple and fast. Using the TSMs in optimum conditions and taking into account the range of uncertainties, one can obtain a first hint on potential source areas.

Evaluation of Water-Chemistry and Water-Level Data at the Henderson Road Superfund Site, Upper Merion Township, Montgomery County, Pennsylvania, 1991-2008

USGS Publications Warehouse

Sloto, Ronald A.

2009-01-01

Several shutdown-rebound tests have been conducted at the Henderson Road Superfund Site, which has been on the U.S. Environmental Protection Agency's National Priorities List since 1984. For a given test, the extraction wells are turned off, and water samples are collected from selected monitor wells at regular intervals before and during cessation of pumping to monitor for changes in chemical concentrations. A long-term shutdown-rebound test began on July 17, 2006. In support of this test, the U.S. Geological Survey conducted this study to determine the effects of shutting down on-site extraction wells on concentrations of selected contaminants and water levels. Concentrations were compared to ARARs (applicable relevant and appropriate requirements), which were set as remediation goals in the Henderson Road Site Record of Decision. Water from 10 wells in and near the source area and to the north, northeast, and northwest of the source area sampled in 2008 exceeded the 5.52 ug/L (micrograms per liter) ARAR for benzene. The greatest changes in benzene concentration between pre-shutdown samples collected in July 2006 and samples collected in February and March 2008 (19 months after the shutdown) were for wells in and north of the source area; increases in benzene concentration ranged from 1.5 to 164 ug/L. Water from five wells in the source area and to the north and northwest of the source area sampled in 2008 exceeded the 60 ug/L ARAR for chlorobenzene. The greatest changes in chlorobenzene concentration between pre-shutdown samples collected in July 2006 and samples collected in February and March 2008 were for wells north of the source area; increases in chlorobenzene concentration ranged from 6.9 to 99 ug/L. The highest concentrations of chlorobenzene were near or outside the northern site boundary, indicating chlorobenzene may have moved north away from the source area; however, no monitor well clusters are on the northern side of the Pennsylvania Turnpike, which is about 190 feet north of the source area. A much larger area was affected by chlorobenzene than benzene. Chlorobenzene concentrations decreased in the source area and increased at and beyond the site boundary. Water from four wells in and northeast of the source area sampled in 2008 exceeded the 5.06 ug/L ARAR for 1,1-dichloroethane (1,1-DCA). Increases in 1,1-DCA concentration between pre-shutdown samples collected in July 2006 and samples collected in February 2008 ranged from 0.4 to 20 ug/L. Water from two wells in the source area sampled in 2008 exceeded the 175 ug/L ARAR for total xylene. The 1,1-DCA and xylene plumes appear to extend in an east-northeast direction from the source area. Large drawdowns in the Upper Merion Reservoir during droughts in 1998 and 2001 affected water levels in the Chester Valley and at the Henderson Road Site, except for well HR-17-170. After the drought of 2001, water levels in the Chester Valley showed a protracted recovery lasting from September 2001 until June 2005 (46 months). Water-level data were evaluated temporally for 1997-2008 and spatially for (1) June 16, 2003, when the extraction wells were pumping at the full rate prior to the start of the June 2003 shutdown test; (2) July 10, 2006, during the period of reduced pumping after the June 2003 shutdown test; and (3) February 25-29, 2008, when the extraction wells were not pumping. Except for well HR-5-195, wells were categorized as shallow, intermediate-depth, and deep wells. The potentiometric surface for shallow wells did not appear to be affected by pumping of the extraction wells. The general direction of ground-water flow was to the north. The potentiometric surface for intermediate-depth wells showed a cone of depression when the extraction wells were pumping at the full rate but did not show a cone of depression when the extraction wells were pumping at the reduced rate. The ground-water-flow direction was toward the north and northeast, similar to

Stable nitrogen isotopes in coastal macroalgae: geographic and anthropogenic variability.

PubMed

Viana, Inés G; Bode, Antonio

2013-01-15

Growing human population adds to the natural nitrogen loads to coastal waters. Both anthropogenic and natural nitrogen is readily incorporated in new biomass, and these different nitrogen sources may be traced by the measurement of the ratio of stable nitrogen isotopes (δ(15)N). In this study δ(15)N was determined in two species of macroalgae (Ascophyllum nodosum and Fucus vesiculosus), and in nitrate and ammonium to determine the relative importance of anthropogenic versus natural sources of nitrogen along the coast of NW Spain. Both algal species and nitrogen sources showed similar isotopic enrichment for a given site, but algal δ(15)N was not related to either inorganic nitrogen concentrations or δ(15)N in the water samples. The latter suggests that inorganic nitrogen inputs are variable and do not always leave an isotopic trace in macroalgae. However, a significant linear decrease in macroalgal δ(15)N along the coast is consistent with the differential effect of upwelling. Besides this geographic variability, the influence of anthropogenic nitrogen sources is evidenced by higher δ(15)N in macroalgae from rias and estuaries compared to those from open coastal areas and in areas with more than 15×10(3) inhabitants in the watershed. These results indicate that, in contrast with other studies, macroalgal δ(15)N is not simply related to either inorganic nitrogen concentrations or human population size but depends on other factors as the upwelling or the efficiency of local waste treatment systems. Copyright © 2012 Elsevier B.V. All rights reserved.

Sensitivity of two dispersion models (AERMOD and ISCST3) to input parameters for a rural ground-level area source.

PubMed

Faulkner, William B; Shaw, Bryan W; Grosch, Tom

2008-10-01

As of December 2006, the American Meteorological Society/U.S. Environmental Protection Agency (EPA) Regulatory Model with Plume Rise Model Enhancements (AERMOD-PRIME; hereafter AERMOD) replaced the Industrial Source Complex Short Term Version 3 (ISCST3) as the EPA-preferred regulatory model. The change from ISCST3 to AERMOD will affect Prevention of Significant Deterioration (PSD) increment consumption as well as permit compliance in states where regulatory agencies limit property line concentrations using modeling analysis. Because of differences in model formulation and the treatment of terrain features, one cannot predict a priori whether ISCST3 or AERMOD will predict higher or lower pollutant concentrations downwind of a source. The objectives of this paper were to determine the sensitivity of AERMOD to various inputs and compare the highest downwind concentrations from a ground-level area source (GLAS) predicted by AERMOD to those predicted by ISCST3. Concentrations predicted using ISCST3 were sensitive to changes in wind speed, temperature, solar radiation (as it affects stability class), and mixing heights below 160 m. Surface roughness also affected downwind concentrations predicted by ISCST3. AERMOD was sensitive to changes in albedo, surface roughness, wind speed, temperature, and cloud cover. Bowen ratio did not affect the results from AERMOD. These results demonstrate AERMOD's sensitivity to small changes in wind speed and surface roughness. When AERMOD is used to determine property line concentrations, small changes in these variables may affect the distance within which concentration limits are exceeded by several hundred meters.

Towards real-time regional earthquake simulation I: real-time moment tensor monitoring (RMT) for regional events in Taiwan

NASA Astrophysics Data System (ADS)

Lee, Shiann-Jong; Liang, Wen-Tzong; Cheng, Hui-Wen; Tu, Feng-Shan; Ma, Kuo-Fong; Tsuruoka, Hiroshi; Kawakatsu, Hitoshi; Huang, Bor-Shouh; Liu, Chun-Chi

2014-01-01

We have developed a real-time moment tensor monitoring system (RMT) which takes advantage of a grid-based moment tensor inversion technique and real-time broad-band seismic recordings to automatically monitor earthquake activities in the vicinity of Taiwan. The centroid moment tensor (CMT) inversion technique and a grid search scheme are applied to obtain the information of earthquake source parameters, including the event origin time, hypocentral location, moment magnitude and focal mechanism. All of these source parameters can be determined simultaneously within 117 s after the occurrence of an earthquake. The monitoring area involves the entire Taiwan Island and the offshore region, which covers the area of 119.3°E to 123.0°E and 21.0°N to 26.0°N, with a depth from 6 to 136 km. A 3-D grid system is implemented in the monitoring area with a uniform horizontal interval of 0.1° and a vertical interval of 10 km. The inversion procedure is based on a 1-D Green's function database calculated by the frequency-wavenumber (fk) method. We compare our results with the Central Weather Bureau (CWB) catalogue data for earthquakes occurred between 2010 and 2012. The average differences between event origin time and hypocentral location are less than 2 s and 10 km, respectively. The focal mechanisms determined by RMT are also comparable with the Broadband Array in Taiwan for Seismology (BATS) CMT solutions. These results indicate that the RMT system is realizable and efficient to monitor local seismic activities. In addition, the time needed to obtain all the point source parameters is reduced substantially compared to routine earthquake reports. By connecting RMT with a real-time online earthquake simulation (ROS) system, all the source parameters will be forwarded to the ROS to make the real-time earthquake simulation feasible. The RMT has operated offline (2010-2011) and online (since January 2012 to present) at the Institute of Earth Sciences (IES), Academia Sinica (http://rmt.earth.sinica.edu.tw). The long-term goal of this system is to provide real-time source information for rapid seismic hazard assessment during large earthquakes.

A Cost-Benefit Analysis for Seafood Processing Training Sessions in the Galveston Bay Area.

ERIC Educational Resources Information Center

Hodgin, Robert F.

A cost-benefit study was conducted to determine the economic viability of continuing to offer training sessions for seafood processors through the College of the Mainland in Texas. Data for the study were collected from both primary and secondary sources, including the college and local company participating in the program, federal and state…

20 CFR 661.260 - What are the requirements for automatic designation of workforce investment areas relating to...

Code of Federal Regulations, 2010 CFR

2010-04-01

..., DEPARTMENT OF LABOR STATEWIDE AND LOCAL GOVERNANCE OF THE WORKFORCE INVESTMENT SYSTEM UNDER TITLE I OF THE WORKFORCE INVESTMENT ACT State Governance Provisions § 661.260 What are the requirements for automatic...(a)(2). The Governor has authority to determine the source of population data to use in making these...

Use of FGD gypsum to reduce p loss from agricultural fields

USDA-ARS?s Scientific Manuscript database

Controlling P loss from agricultural fields has become a major issue in recent years, especially in areas where manure is used as nutrient sources. It is believed that FGD gypsum can be used as a management practice to reduce soluble P loss. Thus, the objective of this study was to determine FGD gy...

INDOOR AND OUTDOOR SOURCE CONTRIBUTIONS TO PERSONAL PM2.5 FOR A PANEL OF INDIVIDUALS WITH CARDIOVASCULAR DISEASE OR COPD LIVING IN BOSTON, MA

EPA Science Inventory

Repeated personal, home indoor, home outdoor, and ambient particulate and gaseous pollutant levels were characterized for individuals with cardiovascular disease or COPD and their partners living in the Boston area. Health status was determined by self-reported history of myoc...

77 FR 43032 - Approval and Promulgation of Implementation Plans; Mississippi: New Source Review-Prevention of...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-23

...'' particles (e.g., sulfate and nitrate) form in the atmosphere as a result of various chemical reactions. The... chemical reactions to form secondary PM). In most areas of the country, PM 2.5 precursor emissions are... determinations for PM 2.5 NAAQS. These requirements address air quality modeling and monitoring provisions for...

76 FR 80754 - Approval and Promulgation of Implementation Plans; State of Kansas: Regional Haze

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-27

... available in the docket for this rulemaking. The supplemental dispersion modeling provided by the State was... determined by using SNCR costs obtained from Jeffrey Unit 1, and scaling the dollar amount using heat input... impact of Kansas BART sources on all Class I areas impacted. NPCA says that the modeling results...

Analytical method for determining rill detachment of purple soil as compared with that of loess soil

USDA-ARS?s Scientific Manuscript database

Rills are commonly found on sloping farmlands in both the loess and purple soil regions of China. Rill erosion is an important component of slope water erosion, and primary sediment sources in small catchments in the areas. A comparative study on rill erosion on loess and purple soils is important t...

A Chemical and Structural Study of the A1N-Si Interface

NASA Technical Reports Server (NTRS)

George, T.; Beye, R.

1997-01-01

Samples of A1N grown on silicon [111] subtrates were examined using electron enery loss spectroscopy (EELS) and selected area diffraction (SAD) with high-resolution transmission electron microscopy (TEM) to determine the source of out-of-place tilts and in-plane rotations of the A1N crystallites at the Si interface.

The Effect of Bypass Nozzle Exit Area on Fan Aerodynamic Performance and Noise in a Model Turbofan Simulator

NASA Technical Reports Server (NTRS)

Hughes, Christopher E.; Podboy, Gary, G.; Woodward, Richard P.; Jeracki, Robert, J.

2013-01-01

The design of effective new technologies to reduce aircraft propulsion noise is dependent on identifying and understanding the noise sources and noise generation mechanisms in the modern turbofan engine, as well as determining their contribution to the overall aircraft noise signature. Therefore, a comprehensive aeroacoustic wind tunnel test program was conducted called the Fan Broadband Source Diagnostic Test as part of the NASA Quiet Aircraft Technology program. The test was performed in the anechoic NASA Glenn 9- by 15-Foot Low Speed Wind Tunnel using a 1/5 scale model turbofan simulator which represented a current generation, medium pressure ratio, high bypass turbofan aircraft engine. The investigation focused on simulating in model scale only the bypass section of the turbofan engine. The test objectives were to: identify the noise sources within the model and determine their noise level; investigate several component design technologies by determining their impact on the aerodynamic and acoustic performance of the fan stage; and conduct detailed flow diagnostics within the fan flow field to characterize the physics of the noise generation mechanisms in a turbofan model. This report discusses results obtained for one aspect of the Source Diagnostic Test that investigated the effect of the bypass or fan nozzle exit area on the bypass stage aerodynamic performance, specifically the fan and outlet guide vanes or stators, as well as the farfield acoustic noise level. The aerodynamic performance, farfield acoustics, and Laser Doppler Velocimeter flow diagnostic results are presented for the fan and four different fixed-area bypass nozzle configurations. The nozzles simulated fixed engine operating lines and encompassed the fan stage operating envelope from near stall to cruise. One nozzle was selected as a baseline reference, representing the nozzle area which would achieve the design point operating conditions and fan stage performance. The total area change from the smallest to the largest nozzle was 12.9 percent of the baseline nozzle area. The results will show that there are significant changes in aerodynamic performance and farfield acoustics as the fan nozzle area is increased. The weight flow through the fan model increased between 7 and 9 percent, the fan and stage pressure dropped between 8 and 10 percent, and the adiabatic efficiency increased between 2 and 3 percent--the magnitude of the change dependent on the fan speed. Results from force balance measurements of fan and outlet guide vane thrust will show that as the nozzle exit area is increased the combined thrust of the fan and outlet guide vanes together also increases, between 2 and 3.5 percent, mainly due to the increase in lift from the outlet guide vanes. In terms of farfield acoustics, the overall sound power level produced by the fan stage dropped nearly linearly between 1 dB at takeoff condition and 3.5 dB at approach condition, mainly due to a decrease in the broadband noise levels. Finally, fan swirl angle survey and Laser Doppler Velocimeter mean velocity and turbulence data obtained in the fan wake will show that the swirl angles and turbulence levels within the wake decrease as the fan nozzle area increases, which helps to explain the drop in the fan broadband noise at all fan speeds.

fMRI activation patterns in an analytic reasoning task: consistency with EEG source localization

NASA Astrophysics Data System (ADS)

Li, Bian; Vasanta, Kalyana C.; O'Boyle, Michael; Baker, Mary C.; Nutter, Brian; Mitra, Sunanda

2010-03-01

Functional magnetic resonance imaging (fMRI) is used to model brain activation patterns associated with various perceptual and cognitive processes as reflected by the hemodynamic (BOLD) response. While many sensory and motor tasks are associated with relatively simple activation patterns in localized regions, higher-order cognitive tasks may produce activity in many different brain areas involving complex neural circuitry. We applied a recently proposed probabilistic independent component analysis technique (PICA) to determine the true dimensionality of the fMRI data and used EEG localization to identify the common activated patterns (mapped as Brodmann areas) associated with a complex cognitive task like analytic reasoning. Our preliminary study suggests that a hybrid GLM/PICA analysis may reveal additional regions of activation (beyond simple GLM) that are consistent with electroencephalography (EEG) source localization patterns.

Contrasting Eutrophication Risks and Countermeasures in Different Water Bodies: Assessments to Support Targeted Watershed Management.

PubMed

Li, Tong; Chu, Chunli; Zhang, Yinan; Ju, Meiting; Wang, Yuqiu

2017-06-29

Eutrophication is a major problem in China. To combat this issue, the country needs to establish water quality targets, monitoring systems, and intelligent watershed management. This study explores a new watershed management method. Water quality is first assessed using a single factor index method. Then, changes in total nitrogen/total phosphorus (TN/TP) are analyzed to determine the limiting factor. Next, the study compares the eutrophication status of two water function districts, using a comprehensive nutritional state index method and geographic information system (GIS) visualization. Finally, nutrient sources are qualitatively analyzed. Two functional water areas in Tianjin, China were selected and analyzed: Qilihai National Wetland Nature Reserve and Yuqiao Reservoir. The reservoir is a drinking water source. Results indicate that total nitrogen (TN) and total phosphorus (TP) pollution are the main factors driving eutrophication in the Qilihai Wetland and Yuqiao Reservoir. Phosphorus was the limiting factor in the Yuqiao Reservoir; nitrogen was the limiting factor in the Qilihai Wetland. Pollution in Qilihai Wetland is more serious than in Yuqiao Reservoir. The study found that external sources are the main source of pollution. These two functional water areas are vital for Tianjin; as such, the study proposes targeted management measures.

Source identification of particulate matter in a semi-urban area of Malaysia using multivariate techniques.

PubMed

Wahid, N B A; Latif, M T; Suan, L S; Dominick, D; Sahani, M; Jaafar, S A; Mohd Tahir, N

2014-03-01

This study aims to determine the composition and sources of particulate matter with an aerodynamic diameter of 10 μm or less (PM10) in a semi-urban area. PM10 samples were collected using a high volume sampler. Heavy metals (Fe, Zn, Pb, Mn, Cu, Cd and Ni) and cations (Na(+), K(+), Ca(2+) and Mg(2+)) were detected using inductively coupled plasma mass spectrometry, while anions (SO4 (2-), NO3 (-), Cl(-) and F(-)) were analysed using Ion Chromatography. Principle component analysis and multiple linear regressions were used to identify the source apportionment of PM10. Results showed the average concentration of PM10 was 29.5 ± 5.1 μg/m(3). The heavy metals found were dominated by Fe, followed by Zn, Pb, Cu, Mn, Cd and Ni. Na(+) was the dominant cation, followed by Ca(2+), K(+) and Mg(2+), whereas SO4 (2-) was the dominant anion, followed by NO3 (-), Cl(-) and F(-). The main sources of PM10 were the Earth's crust/road dust, followed by vehicle emissions, industrial emissions/road activity, and construction/biomass burning.

Development and application of methods used to source prehistoric Southwestern maize: a review

USGS Publications Warehouse

Benson, Larry V.

2012-01-01

Archaeological cobs free of mineral contaminants should be used to source the soils in which they were grown. Mineral contaminants often contain much higher concentrations of metals than vegetal materials and can alter a cob’s apparent metal and heavy-isotope content. Cleaning a cob via immersion in an acid solution for more than a few minutes will result in the incongruent and sometimes complete leaching of metals, including strontium (Sr), from the cob. When using 87Sr/Sr to determine the location of potential agriculture fields, it is best to either integrate several depth-integrated soil samples or to integrate several vegetation samples from individual fields. Biologically labile Sr in semi-arid Southwestern soils largely originates from eolian source or sources and usually is not derived from underlying bedrock. Existing Sr-isotope data indicate that archaeological cobs from Aztec Ruins came from either the Mesa Verde-McElmo Dome or Totah areas, that Pueblo Bonito and Chetro Ketl cobs, from Chaco Canyon that predate A.D. 1130, probably came from the Rio Chaco corridor, and that cobs from Chaco Canyon, that postdate A.D. 1130, probably came from either the Totah or Zuni areas.

Hydrological modelling of snail dispersal patterns in Msambweni, Kenya and potential resurgence of Schistosoma haematobium transmission.

PubMed

Clennon, J A; King, C H; Muchiri, E M; Kitron, U

2007-05-01

Urinary schistosomiasis is an important source of human morbidity in Msambweni, Kenya, where the intermediate host snail, Bulinus nasutus is found in ponds and water pools. In the past, aquatic habitats in the area have been studied separately; however, recent collections of B. nasutus snails and shells indicated that many of these ponds are in fact connected during and following sufficient rains. Satellite imagery and a geographical information system (GIS) were used to survey the main water courses and potential drainage routes, to locate potential source populations of snails and to determine probable snail dispersal routes. The 2 water bodies implicated as being the most important Schistosoma haematobium transmission foci in the area were found to differ in their degree of connectivity to other B. nasutus source habitats. One pond becomes connected even after normal rains, while the other pond requires prolonged rains or flooding to become connected with source habitats. Consequently, the transmission foci differ in their susceptibility to snail population control measures. Spatially explicit dispersal models that consider the spatial and temporal patterns of connectivity between aquatic habitats will contribute to improved snail surveillance and more focused control for urinary schistosomiasis at a local level.

Somatosensory responses in normal aging, mild cognitive impairment, and Alzheimer's disease.

PubMed

Stephen, Julia M; Montaño, Rebecca; Donahue, Christopher H; Adair, John C; Knoefel, Janice; Qualls, Clifford; Hart, Blaine; Ranken, Doug; Aine, Cheryl J

2010-02-01

As a part of a larger study of normal aging and Alzheimer's disease (AD), which included patients with mild cognitive impairment (MCI), we investigated the response to median nerve stimulation in primary and secondary somatosensory areas. We hypothesized that the somatosensory response would be relatively spared given the reported late involvement of sensory areas in the progression of AD. We applied brief pulses of electric current to left and right median nerves to test the somatosensory response in normal elderly (NE), MCI, and AD. MEG responses were measured and were analyzed with a semi-automated source localization algorithm to characterize source locations and timecourses. We found an overall difference in the amplitude of the response of the primary somatosensory source (SI) based on diagnosis. Across the first three peaks of the SI response, the MCI patients exhibited a larger amplitude response than the NE and AD groups (P < 0.03). Additional relationships between neuropsychological measures and SI amplitude were also determined. There was no significant difference in amplitude for the contralateral secondary somatosensory source across diagnostic category. These results suggest that somatosensory cortex is affected early in the progression of AD and may have some consequence on behavioral and functional measures.

Characterization of a Surface-Flashover Ion Source with 10-250 ns Pulse Widths

NASA Astrophysics Data System (ADS)

Falabella, S.; Guethlein, G.; Kerr, P. L.; Meyer, G. A.; Morse, J. D.; Sampayan, S.; Tang, V.

2009-03-01

As a step towards developing an ultra compact D-D neutron source for various defense and homeland security applications, a compact ion source is needed. Towards that end, we are testing a pulsed, surface flashover source, with deuterated titanium films deposited on alumina substrates as the electrodes. An electrochemically-etched mask was used to define the electrode areas on the substrate during the sputtered deposition of the titanium films. Deuterium loading of the films was performed in an all metal-sealed vacuum chamber containing a heated stage. Deuterium ion current from the source was determined by measuring the neutrons produced when the ions impacted a deuterium-loaded target held at -90 kV. As the duration of the arc current is varied, it was observed that the integrated deuteron current per pulse initially increases rapidly, then reaches a maximum near a pulse length of 100 ns.

Darrieus wind-turbine and pump performance for low-lift irrigation pumping

NASA Astrophysics Data System (ADS)

Hagen, L. J.; Sharif, M.

1981-10-01

In the Great Plains about 15 percent of the irrigation water pumped on farms comes from surface water sources; for the United States as a whole, the figure is about 22 percent. Because of forecast fuel shortages, there is a need to develop alternative energy sources such as wind power for surface water pumping. Specific objectives of this investigation were to: design and assemble a prototype wind powered pumping system for low lift irrigation pumping; determine performance of the prototype system; design and test an irrigation system using the wind powered prototype in a design and test an farm application; and determine the size combinations of wind turbines, tailwater pits, and temporary storage reservoirs needed for successful farm application of wind powered tailwater pumping systems in western Kansas. The power source selected was a two bladed, 6 m diameter, 9 m tall Darrieus vertical axis wind turbine with 0.10 solidity and 36.1 M(2) swept area.

A field instrument for quantitative determination of beryllium by activation analysis

USGS Publications Warehouse

Vaughn, William W.; Wilson, E.E.; Ohm, J.M.

1960-01-01

A low-cost instrument has been developed for quantitative determinations of beryllium in the field by activation analysis. The instrument makes use of the gamma-neutron reaction between gammas emitted by an artificially radioactive source (Sb124) and beryllium as it occurs in nature. The instrument and power source are mounted in a panel-type vehicle. Samples are prepared by hand-crushing the rock to approximately ?-inch mesh size and smaller. Sample volumes are kept constant by means of a standard measuring cup. Instrument calibration, made by using standards of known BeO content, indicates the analyses are reproducible and accurate to within ? 0.25 percent BeO in the range from 1 to 20 percent BeO with a sample counting time of 5 minutes. Sensitivity of the instrument maybe increased somewhat by increasing the source size, the sample size, or by enlarging the cross-sectional area of the neutron-sensitive phosphor normal to the neutron flux.

Determination of the Priority Aspect in Process of Determining Urban Residential Area

NASA Astrophysics Data System (ADS)

Bhekti Pribadi, Cherie; Hariyanto, Teguh

2017-12-01

Recently, the population growth is increasingly crowded in urban area and as a source of land supply for housing development into the needs of each individual becomes increasingly limited. the home is one of the basic rights of the people and therefore every citizen has the right to reside and got a good environment and healthy. Besides the house is also a basic human need to enhance the dignity, the dignity, quality of life and livelihood, as well as personal self-reflection in order to improve the standard of living, as well as the formation of character, character and personality of the nation. The construction of such housing should always take into consideration many aspects in order to create a balanced environment not only based on the suitability of land but also based on the aspects that exist in surrounding. Therefore, this study will be to analyze the priority aspect in process of determining urban residential area using Analytical Hierarchy Process Method. This method aims to determine priority aspect were used based on primary data collection form of questionnaires and interviews to respondents who expert in the field.

A trial of reliable estimation of non-double-couple component of microearthquakes

NASA Astrophysics Data System (ADS)

Imanishi, K.; Uchide, T.

2017-12-01

Although most tectonic earthquakes are caused by shear failure, it has been reported that injection-induced seismicity and earthquakes occurring in volcanoes and geothermal areas contain non double couple (non-DC) components (e.g, Dreger et al., 2000). Also in the tectonic earthquakes, small non-DC components are beginning to be detected (e.g, Ross et al., 2015). However, it is generally limited to relatively large earthquakes that the non-DC component can be estimated with sufficient accuracy. In order to gain further understanding of fluid-driven earthquakes and fault zone properties, it is important to estimate full moment tensor of many microearthquakes with high precision. In the last AGU meeting, we proposed a method that iteratively applies the relative moment tensor inversion (RMTI) (Dahm, 1996) to source clusters improving each moment tensor as well as their relative accuracy. This new method overcomes the problem of RMTI that errors in the mechanism of reference events lead to biased solutions for other events, while taking advantage of RMTI that the source mechanisms can be determined without a computation of Green's function. The procedure is briefly summarized as follows: (1) Sample co-located multiple earthquakes with focal mechanisms, as initial solutions, determined by an ordinary method. (2) Apply the RMTI to estimate the source mechanism of each event relative to those of the other events. (3) Repeat the step 2 for the modified source mechanisms until the reduction of total residual converges. In order to confirm whether the method can resolve non-DC components, we conducted numerical tests on synthetic data. Amplitudes were computed assuming non-DC sources, amplifying by factor between 0.2 and 4 as site effects, and adding 10% random noise. As initial solutions in the step 1, we gave DC sources with arbitrary strike, dip and rake angle. In a test with eight sources at 12 stations, for example, all solutions were successively improved by iteration. Non-DC components were successfully resolved in spite of the fact that we gave DC sources as initial solutions. The application of the method to microearthquakes in geothermal area in Japan will be presented.

Determination of bromine, chlorine and iodine in environmental aqueous samples by epithermal neutron activation analysis and Compton suppression

USGS Publications Warehouse

Landsberger, S.; O'Kelly, D. J.; Braisted, J.; Panno, S.

2006-01-01

Halides, particularly Br- and Cl-, have been used as indicators of potential sources of Na+ and Cl- in surface water and groundwater with limited success. Contamination of groundwater and surface water by Na+ and Cl- is a common occurrence in growing urban areas and adversely affects municipal and private water supplies in Illinois and other states, as well as vegetation in environmentally sensitive areas. Neutron activation analysis (NAA) can be effectively used to determine these halogens, but often the elevated concentrations of sodium and chlorine in water samples can give rise to very high detection limits for bromine and iodine due to elevated backgrounds from the activation process. We present a detailed analytical scheme to determine Cl, Br and I in aqueous samples with widely varying Na and Cl concentrations using epithermal NAA in conjunction with Compton suppression. ?? 2006 Akade??miai Kiado??.

Community Response to Multiple Sound Sources: Integrating Acoustic and Contextual Approaches in the Analysis

PubMed Central

Lercher, Peter; De Coensel, Bert; Dekonink, Luc; Botteldooren, Dick

2017-01-01

Sufficient data refer to the relevant prevalence of sound exposure by mixed traffic sources in many nations. Furthermore, consideration of the potential effects of combined sound exposure is required in legal procedures such as environmental health impact assessments. Nevertheless, current practice still uses single exposure response functions. It is silently assumed that those standard exposure-response curves accommodate also for mixed exposures—although some evidence from experimental and field studies casts doubt on this practice. The ALPNAP-study population (N = 1641) shows sufficient subgroups with combinations of rail-highway, highway-main road and rail-highway-main road sound exposure. In this paper we apply a few suggested approaches of the literature to investigate exposure-response curves and its major determinants in the case of exposure to multiple traffic sources. Highly/moderate annoyance and full scale mean annoyance served as outcome. The results show several limitations of the current approaches. Even facing the inherent methodological limitations (energy equivalent summation of sound, rating of overall annoyance) the consideration of main contextual factors jointly occurring with the sources (such as vibration, air pollution) or coping activities and judgments of the wider area soundscape increases the variance explanation from up to 8% (bivariate), up to 15% (base adjustments) up to 55% (full contextual model). The added predictors vary significantly, depending on the source combination. (e.g., significant vibration effects with main road/railway, not highway). Although no significant interactions were found, the observed additive effects are of public health importance. Especially in the case of a three source exposure situation the overall annoyance is already high at lower levels and the contribution of the acoustic indicators is small compared with the non-acoustic and contextual predictors. Noise mapping needs to go down to levels of 40 dBA,Lden to ensure the protection of quiet areas and prohibit the silent “filling up” of these areas with new sound sources. Eventually, to better predict the annoyance in the exposure range between 40 and 60 dBA and support the protection of quiet areas in city and rural areas in planning sound indicators need to be oriented at the noticeability of sound and consider other traffic related by-products (air quality, vibration, coping strain) in future studies and environmental impact assessments. PMID:28632198

Use of bromide:Chloride ratios to differentiate potential sources of chloride in a shallow, unconfined aquifer affected by brackish-water intrusion

USGS Publications Warehouse

Andreasen, D.C.; Fleck, W.B.

1997-01-01

Brackish water from Chesapeake Bay and its tributaries has entered the Aquia aquifer in east-central Anne Arundel County, Maryland, USA. This determination was made based on chloride analyses of water samples collected in wells screened in the Aquia aquifer between October 1988 and May 1989. The Aquia aquifer, which is composed of fine- to medium-grained sand, is a shallow, unconfined aquifer in this area. Land use is primarily urban, consisting of a mixture of residential and light commercial areas. Associated with the urban setting is the potential for chloride contamination to enter the Aquia aquifer from anthropogenic sources, such as residential septic-tank effluent, leaky public sewer lines, road-deicing salt, stormwater infiltration basins, and domestic water-conditioning recharge effluent. In order to map the distribution of bay-water intrusion in the Aquia aquifer, chloride derived from Chesapeake Bay was differentiated from chloride derived from anthropogenic sources by comparing the ratio of dissolved bromide to dissolved chloride (bromide:chloride) in groundwater to the distinctive ratio in Chesapeake Bay water. Two additional factors considered in determining the source of the chloride were nitrogen concentrations and well-screen positions of sampled wells in relation to the estimated depth of the fresh-water/brackish-water interface. Of 36 Aquia-aquifer water samples with chloride concentrations greater than 30 mg/L, 22 had bromide:chloride ratios similar to the ratio in Chesapeake Bay water, an indication that bay water is the primary source of the chloride. Of the other 14 samples with bromide:chloride ratios dissimilar to the ratio in Chesapeake Bay water, seven were from wells where screen positions were substantially above the estimated fresh-water/brackish-water interface. Three of these samples had nitrogen concentrations (as nitrite plus nitrate) greater than 3.0 mg/L, an indication that chloride in these groundwater samples comes from anthropogenic sources, at least in part.

Investigation of dust storms entering Western Iran using remotely sensed data and synoptic analysis.

PubMed

Boloorani, Ali D; Nabavi, Seyed O; Bahrami, Hosain A; Mirzapour, Fardin; Kavosi, Musa; Abasi, Esmail; Azizi, Rasoul

2014-01-01

One of the natural phenomena which have had considerable impacts on various regions of the world, including Iran, is "dust storm". In recent years, this phenomenon has taken on new dimensions in Iran and has changed from a local problem to a national issue. This study is an attempt to investigate the formation of the dust storms crossing the Western Iran. To find the sources of the dust storms entering Iran, first we examine three determined dust paths in the region and their temporal activities, using MODIS satellite images. Then, four regions were identified as dust sources through soil, land cover and wind data. Finally, atmospheric analyses are implemented to find synoptic patterns inducing dust storms. Source 1 has covered the region between the eastern banks of Euphrates and western banks of Tigris. Source 2 is in desert area of western and south-western Iraq. Finally source 3 is bounded in eastern and south-eastern deserts of Saudi Arabia called Rub-Al-Khali desert, or Empty Quarter. Moreover, south-eastern part of Iraq (source 4) was also determined as a secondary source which thickens the dust masses originating from the above mentioned sources. The study of synoptic circulations suggests that the dust storms originating from source 1 are formed due to the intense pressure gradient between the low-pressure system of Zagros and a high-pressure cell formed on Mediterranean Sea. The dust events in sources 2 and 3 are outcomes of the atmospheric circulations dominant in the cold period of the year in mid-latitudes.

The Anthropogenic/Lightning Effects Around Houston: The Houston Environmental Aerosol Thunderstorm (HEAT) Project - 2005

NASA Astrophysics Data System (ADS)

Orville, R. E.

2004-12-01

A major field program will occur in summer 2005 to determine the sources and causes for the enhanced cloud-to-ground lightning over Houston, Texas. This program will be in association with simultaneous experiments supported by the Environmental Protection Agency (EPA) and the Texas Commission on Environmental Quality (TCEQ), formally the Texas Natural Resource Conservation Commission (TNRCC). Recent studies covering the period 1989-2002 document a 60 percent increase of cloud-to-ground lightning in the Houston area as compared to surrounding background values, which is second in flash density only to the Tampa Bay, Florida area. We suggest that the elevated flash densities could result from several factors, including 1) the convergence due to the urban heat island effect and complex sea breeze (thermal hypothesis), and 2) the increasing levels of air pollution from anthropogenic sources producing numerous small cloud droplets and thereby suppressing mean droplet size (aerosol hypothesis). The latter effect would enable more cloud water to reach the mixed phase region where it is involved in the formation of precipitation and the separation of electric charge, leading to an enhancement of lightning. The primary goals of HEAT are to examine the effects of (1) pollution, (2) the urban heat island, and (3) the complex coastline on storms and lightning characteristics in the Houston area. The transport of air pollutants by Houston thunderstorms will be investigated. In particular, the relative amounts of lightning-produced and convectively transported NOx into the upper troposphere will be determined, and a comparison of the different NOx sources in the urban area of Houston will be developed. The HEAT project is based on the observation that there is an enhancement in cloud-to-ground (CG) lightning. Total lightning (intracloud (IC) and CG) will be measured using a lightning mapping system (LDAR II) to observe if there is an enhancement in intracloud lightning as well.

Irradiation of Population in the Surrounding Area of Nuclear Power Plant Temelin

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thinova, Lenka; Kluson, Jaroslav

In monitoring the impact of nuclear facilities operation on ecosystem, it is necessary to consider, what part of biota irradiation can be caused by an artificial source. For the estimation of an effective dose from natural sources were used measurements of dosimetric and gamma spectrometric characteristics of photon fields, (performed in the area of NPP Temelin since year 2000) and data from the Czech Republic radiometric chart, including the results from radon volume activity measurements in dwellings. For gamma spectrometric measurements in situ were selected two methodologies and for measurement were used corresponding types of equipment (Tesla NB3201 and spectrometermore » NaI(TI) 3''x3'') at selected locations within the monitored area: i) determination of air kerma rate (through direct measurement and by calculationfrom spectrometric data); ii) measurement of photon spectra by an scintillating spectrometer. For a dose assessment from artificial sources resulting from past or present operation of NPP Temelin, were used records from all so far performed laboratory and field measurements of NPP releases, food baskets and also results of a 6 year ecosystem monitoring in the surrounding area of NPP Temelin. The ecosystem monitoring is based on studying the contamination of the following bioindicators: forest humus, Pine bark, Schreber's Moss, the Bay Bolete (mushroom) and forest berries. Each year 220 samples are collected and mass activity (Bq/kg) for eventual contaminants is determined using laboratory gamma spectroscopy. For measurements is used a coaxial HPGe detector, with samples in the geometry of 'Marinelli' container. For evaluation of the laboratory results obtained is used trend analysis. The above described monitoring has been performed from the year 2000 until now (the year 2000 is pre-operational). In all measured laboratory spectra, of all analyzed samples, were not identified any non-natural radionuclides, with the exception of {sup 137}Cs, for which maesured activities correspond, within allowed measurement error, to the conditions before the start of NPP Temelin operation.« less

Sources and yields of dissolved carbon in northern Wisconsin stream catchments with differing amounts of Peatland

USGS Publications Warehouse

Elder, J.F.; Rybicki, N.B.; Carter, V.; Weintraub, V.

2000-01-01

In five tributary streams (four inflowing and one outflowing) of 1600-ha Trout Lake in northern Wisconsin, USA, we examined factors that can affect the magnitude of stream flow and transport of dissolved organic and inorganic carbon (DOC and DIC) through the streams to the lake. One catchment, the Allequash Creek basin, was investigated in more detail to describe the dynamics of carbon flow and to identify potential carbon sources. Stream flows and carbon loads showed little or no relation to surface-water catchment area. They were more closely related to ground-water watershed area because ground-water discharge, from both local and regional sources, is a major contributor to the hydrologic budgets of these catchments. An important factor in determining carbon influx to the stream is the area of peatland in the catchment. Peatland porewaters contain DOC concentrations up to 40 mg l-1 and are a significant potential carbon source. Ground-water discharge and lateral flow through peat are the suspected mechanisms for transport of that carbon to the streams. Carbon and nitrogen isotopes suggested that the sources of DOC in Allequash Creek above Allequash Lake were wetland vegetation and peat and that the sources below Allequash Lake were filamentous algae and wild rice. Catchments with high proportions of peatland, including the Allequash Creek catchment, tended to have elevated DOC loads in outflowing stream water. Respiration and carbon mineralization in lakes within the system tend to produce low DOC and low DOC/DIC in lake outflows, especially at Trout Lake. In Allequash Lake, however, the shallow peat island and vegetation-filled west end were sources of DOC. Despite the vast carbon reservoir in the peatlands, carbon yields were very low in these catchments. Maximum yields were on the order of 2.5 g m-2 y-1 DOC and 5.5 g m-2 y-1 DIC. The small yields were attributable to low stream flows due to lack of significant overland runoff and very limited stream channel coverage of the total catchment area.

Multivariate statistical and lead isotopic analyses approach to identify heavy metal sources in topsoil from the industrial zone of Beijing Capital Iron and Steel Factory.

PubMed

Zhu, Guangxu; Guo, Qingjun; Xiao, Huayun; Chen, Tongbin; Yang, Jun

2017-06-01

Heavy metals are considered toxic to humans and ecosystems. In the present study, heavy metal concentration in soil was investigated using the single pollution index (PIi), the integrated Nemerow pollution index (PIN), and the geoaccumulation index (Igeo) to determine metal accumulation and its pollution status at the abandoned site of the Capital Iron and Steel Factory in Beijing and its surrounding area. Multivariate statistical (principal component analysis and correlation analysis), geostatistical analysis (ArcGIS tool), combined with stable Pb isotopic ratios, were applied to explore the characteristics of heavy metal pollution and the possible sources of pollutants. The results indicated that heavy metal elements show different degrees of accumulation in the study area, the observed trend of the enrichment factors, and the geoaccumulation index was Hg > Cd > Zn > Cr > Pb > Cu ≈ As > Ni. Hg, Cd, Zn, and Cr were the dominant elements that influenced soil quality in the study area. The Nemerow index method indicated that all of the heavy metals caused serious pollution except Ni. Multivariate statistical analysis indicated that Cd, Zn, Cu, and Pb show obvious correlation and have higher loads on the same principal component, suggesting that they had the same sources, which are related to industrial activities and vehicle emissions. The spatial distribution maps based on ordinary kriging showed that high concentrations of heavy metals were located in the local factory area and in the southeast-northwest part of the study region, corresponding with the predominant wind directions. Analyses of lead isotopes confirmed that Pb in the study soils is predominantly derived from three Pb sources: dust generated during steel production, coal combustion, and the natural background. Moreover, the ternary mixture model based on lead isotope analysis indicates that lead in the study soils originates mainly from anthropogenic sources, which contribute much more than the natural sources. Our study could not only reveal the overall situation of heavy metal contamination, but also identify the specific pollution sources.

Heavy Metal Pollution in Settled Dust Associated with Different Urban Functional Areas in a Heavily Air-Polluted City in North China.

PubMed

Wan, Dejun; Han, Zhangxiong; Yang, Jinsong; Yang, Guanglin; Liu, Xingqi

2016-11-10

Understanding variations of heavy metals in atmospheric particles between different functional areas is significant for pollution control and urban planning in cities. To reveal pollution and spatial distribution of heavy metals in atmospheric particles from different urban functional areas in Shijiazhuang in North China, 43 settled dust samples were collected over the main urban area and heavy metal concentrations were determined in their <63 μm fractions using an ICP-OES. The results suggest that Cr, Mn, Fe, Co, Ni, and V in the dust are not or slightly enriched and their concentrations vary slightly between different sites, implying their natural origins; whereas Cu, Zn, Cd, and Pb are often notably enriched and their concentrations vary significantly between different functional areas, indicating their anthropogenic sources. Integrated pollution indexes (IPIs) of the ten heavy metals are 2.7-13.6 (5.7 ± 2.2), suggesting high or very high pollution levels of most dust. Relatively lower IPIs occur mainly in the administration-education area, the commercial area, and other unclassified sites; while peaks occur mainly in the North Railway Station, the northeastern industrial area, and some sites near heavily trafficked areas, implying the significant influence of intensive industrial (including coal combustion) and traffic activities on atmospheric heavy metal accumulation. These results suggest a clear need of mitigating atmospheric heavy metal pollution via controlling emissions of toxic metals (especially Cd and Pb) from industrial and traffic sources in the city.

Heavy Metal Pollution in Settled Dust Associated with Different Urban Functional Areas in a Heavily Air-Polluted City in North China

PubMed Central

Wan, Dejun; Han, Zhangxiong; Yang, Jinsong; Yang, Guanglin; Liu, Xingqi

2016-01-01

Understanding variations of heavy metals in atmospheric particles between different functional areas is significant for pollution control and urban planning in cities. To reveal pollution and spatial distribution of heavy metals in atmospheric particles from different urban functional areas in Shijiazhuang in North China, 43 settled dust samples were collected over the main urban area and heavy metal concentrations were determined in their <63 μm fractions using an ICP-OES. The results suggest that Cr, Mn, Fe, Co, Ni, and V in the dust are not or slightly enriched and their concentrations vary slightly between different sites, implying their natural origins; whereas Cu, Zn, Cd, and Pb are often notably enriched and their concentrations vary significantly between different functional areas, indicating their anthropogenic sources. Integrated pollution indexes (IPIs) of the ten heavy metals are 2.7–13.6 (5.7 ± 2.2), suggesting high or very high pollution levels of most dust. Relatively lower IPIs occur mainly in the administration-education area, the commercial area, and other unclassified sites; while peaks occur mainly in the North Railway Station, the northeastern industrial area, and some sites near heavily trafficked areas, implying the significant influence of intensive industrial (including coal combustion) and traffic activities on atmospheric heavy metal accumulation. These results suggest a clear need of mitigating atmospheric heavy metal pollution via controlling emissions of toxic metals (especially Cd and Pb) from industrial and traffic sources in the city. PMID:27834903

Leaching of mercury from seal carcasses into Antarctic soils.

PubMed

Zvěřina, Ondřej; Coufalík, Pavel; Brat, Kristián; Červenka, Rostislav; Kuta, Jan; Mikeš, Ondřej; Komárek, Josef

2017-01-01

More than 400 seal mummies and skeletons are now mapped in the northern part of James Ross Island, Antarctica. Decomposing carcasses represent a rare source of both organic matter and associated elements for the soil. Owing to their high trophic position, seals are known to carry a significant mercury body burden. This work focuses on the extent of the mercury input from seal carcasses and shows that such carcasses represent locally significant sources of mercury and methylmercury for the environment. Mercury contents in soil samples from the surrounding areas were determined using a single-purpose AAS mercury analyzer. For the determination of methylmercury, an ultra-sensitive isotopic dilution HPLC-ICP-MS technique was used. In the soils lying directly under seal carcasses, mercury contents were higher, with levels reaching almost 40 μg/kg dry weight of which methylmercury formed up to 2.8 % of the total. The spatial distribution implies rather slow vertical transport to the lower soil layers instead of a horizontal spread. For comparison, the background level of mercury in soils of the investigated area was found to be 8 μg/kg dry weight, with methylmercury accounting for less than 0.1 %. Apart from the direct mercury input, an enhanced level of nutrients in the vicinity of carcasses enables the growth of lichens and mosses with accumulative ability with respect to metals. The enhanced capacity of soil to retain mercury is also anticipated due to the high content of total organic carbon (from 1.6 to 7.5 %). According to the results, seal remains represent a clear source of mercury in the observed area.

Exposure to nanoscale particles and fibers during machining of hybrid advanced composites containing carbon nanotubes

NASA Astrophysics Data System (ADS)

Bello, Dhimiter; Wardle, Brian L.; Yamamoto, Namiko; Guzman deVilloria, Roberto; Garcia, Enrique J.; Hart, Anastasios J.; Ahn, Kwangseog; Ellenbecker, Michael J.; Hallock, Marilyn

2009-01-01

This study investigated airborne exposures to nanoscale particles and fibers generated during dry and wet abrasive machining of two three-phase advanced composite systems containing carbon nanotubes (CNTs), micron-diameter continuous fibers (carbon or alumina), and thermoset polymer matrices. Exposures were evaluated with a suite of complementary instruments, including real-time particle number concentration and size distribution (0.005-20 μm), electron microscopy, and integrated sampling for fibers and respirable particulate at the source and breathing zone of the operator. Wet cutting, the usual procedure for such composites, did not produce exposures significantly different than background whereas dry cutting, without any emissions controls, provided a worst-case exposure and this article focuses here. Overall particle release levels, peaks in the size distribution of the particles, and surface area of released particles (including size distribution) were not significantly different for composites with and without CNTs. The majority of released particle surface area originated from the respirable (1-10 μm) fraction, whereas the nano fraction contributed 10% of the surface area. CNTs, either individual or in bundles, were not observed in extensive electron microscopy of collected samples. The mean number concentration of peaks for dry cutting was composite dependent and varied over an order of magnitude with highest values for thicker laminates at the source being >1 × 106 particles cm-3. Concentration of respirable fibers for dry cutting at the source ranged from 2 to 4 fibers cm-3 depending on the composite type. Further investigation is required and underway to determine the effects of various exposure determinants, such as specimen and tool geometry, on particle release and effectiveness of controls.

Markers and influence of open biomass burning on atmospheric particulate size and composition during a major bonfire event

NASA Astrophysics Data System (ADS)

Vassura, Ivano; Venturini, Elisa; Marchetti, Sara; Piazzalunga, Andrea; Bernardi, Elena; Fermo, Paola; Passarini, Fabrizio

2014-01-01

This study aims to characterize PM from the open burning of bonfires as well as detect a series of useful tracer species for source apportionment studies. Total suspended particulate (TSP), PM10 and PM2.5 were collected before, during, and after St. Joseph's Eve (18th of March). On this day, several bonfires are lit throughout the study area. Levoglucosan (Lvg), OC, EC, PAHs, soluble ions, and some metals (Al, Cd, Cu, Ni, and Pb) have been determined in each fraction. Results show that the contamination of the area is similar to what is generally found in suburban areas. The fine fraction makes the highest contribution to PM. This fraction is mainly related to compounds composing the PM secondarily formed, while the coarser fractions are associated with natural matrices. The bonfire event is an important source of particulate. All the combustion markers determined in PM2.5 (EC, OC, PAHs (except for Flu and Pyr), K+, Cl-, and Lvg) register a higher concentration. Lvg/OC ratio confirms higher wood smoke emissions during these days. Both the concentration and the compound profile indicate a different origin of PAHs in the atmosphere. The highest concentration of K+ and OC in TSP confirm the contribution of open fire, as well, to this fraction, which can be ascribable mainly to combustion ash. Nitrates and sulphates also show a higher concentration in the PM10-TSP fraction. Surprisingly, there is also an increase in the concentration of components not usually considered combustion markers, i.e. Pb and Al in PM2.5. This is probably ascribable to their bioaccumulation. In conclusion, Lvg, OC, PAHs, Al, and Pb can be used together as specific markers of bonfires to identify this source of particulate matter.

Variable-source flood pulsing in a semi-arid transboundary watershed: the Chobe River, Botswana and Namibia.

PubMed

Pricope, Narcisa G

2013-02-01

The Chobe River, characterized by an unusual flood pulsing regime and shared between Botswana and Namibia, lies at the heart of the world's largest transfrontier conservation area (the Kavango-Zambezi Transfrontier Conservation Area). Significant ecological changes and vegetation conversions are occurring along its floodplains. Various scenarios for agricultural and urban water use are currently being proposed by the government of Botswana. However, the understanding of the river's annual flow regime and timing of the relative contributions of water from three different sources is relatively poor. In light of past and future climate change and variability, this means that allocating water between ecological flows and economic and domestic uses will become increasingly challenging. We reconstruct the inundation history in this basin to help ease this challenge. This paper presents a spatiotemporal approach to estimate the contribution of water from various sources and the magnitude of changes in the flooding extent in the basin between 1985 and 2010. We used time series analysis of bimonthly NOAA AVHRR and NASA MODIS data and climatologic and hydrologic records to determine the flooding timing and extent. The results indicate that between 12 and 62 % of the basin is flooded on an annual basis and that the spatial extent of the flooding varies throughout the year as a function of the timing of peak discharge in two larger basins. A 30-year trend analysis indicates a consistent decline in the average monthly flooded area in the basin. The results may prove useful in future water utilization feasibility studies, in determining measures for protecting ecological flows and levels, and in ecosystem dynamics studies in the context of current and future climate change and variability.

Assessment of natural attenuation of ground-water contamination at sites FT03, LF13, and WP14/LF15, Dover Air Force Base, Delaware

USGS Publications Warehouse

Barbaro, Jeffrey R.

2002-01-01

Water-quality, aquifer-sediment, and hydro-logic data were used to assess the effectiveness of natural attenuation of ground-water contamination at Fire Training Area Three, the Rubble Area Landfill, the Liquid Waste Disposal Landfill, and the Receiver Station Landfill in the East Management Unit of Dover Air Force Base, Delaware. These sites, which are contaminated with chlorinated solvents and fuel hydrocarbons, are under-going long-term monitoring to determine if natural attenuation continues to sufficiently reduce contaminant concentrations to meet regulatory requirements. This report is the first assessment of the effectiveness of natural attenuation at these sites since long-term monitoring began in 1999, and follows a preliminary investigation done in 1995?96. This assessment was done by the U.S. Geological Survey in cooperation with the U.S. Air Force.Since 1995?96, additional information has been collected and used in the current assessment. The conclusions in this report are based primarily on ground-water samples collected from January through March 2000. Previous analytical results from selected wells, available geologic and geo-physical well logs, and newly acquired information such as sediment organic-carbon measurements, hydraulic-conductivity measurements determined from slug tests on wells in the natural attenuation study area, and water-level measurements from surficial-aquifer wells also were used in this assessment. This information was used to: (1) calculate retardation factors and estimate contaminant migration velocities, (2) improve estimates of ground-water flow directions and inferred contaminant migration pathways, (3) better define the areal extent of contamination and the proximity of contaminants to discharge areas and the Base boundary, (4) develop a better under-standing of the vertical variability of contaminant concentrations and redox conditions, (5) evaluate the effects of temporal changes on concentrations in the plumes and source areas, and (6) determine whether intrinsic biodegradation is occurring at these sites.The water-quality data indicate that intrinsic biodegradation is occurring at all three sites. The strongest indication of intrinsic biodegradation is the detection of tetrachloroethene and trichloroethene breakdown products within and down-gradient of the source areas. The patterns of electron acceptors and metabolic by-products indicate that contaminant biodegradation has changed the prevailing geochemistry of the surficial aquifer, creating the strongly reducing conditions necessary for chlorinated solvent bio-degradation. Geochemical changes include depleted dissolved oxygen and elevated ferrous iron and methane levels relative to concentrations in uncontaminated zones of the surficial aquifer. At Fire Training Area Three and the Rubble Area Landfill sites, natural attenuation appears to be adequate for controlling the migration of the contaminant plumes. At the third site, the Liquid Waste Disposal and Receiver Station Landfills, the plume is larger and the uncertainty about the effectiveness of natural attenuation in reducing contaminant concentrations and controlling plume migration is greater. Ground-water data indicate, however, that U.S. Environmental Protection Agency maximum contaminant levels were not exceeded in any point-of-compliance wells located along the Base boundary.The information presented in this report led to the development of improved conceptual models for these sites, and to the recognition of four issues that are currently unclear and may need further study. These issues include delineating the areal and vertical extent of the contaminant plumes in greater detail, determining the extent of intrinsic biodegradation downgradient of the Liquid Waste Disposal and Receiver Station Landfills, deter-mining the fate of contaminants in the ground-water discharge areas, and determining the effect of temporal variability in source concentrations and ground-water

Measurements of Greenhouse Gases around the Sacramento Area: The Airborne Greenhouse Emissions Survey (AGES) Campaign

NASA Astrophysics Data System (ADS)

Karion, A.; Fischer, M. L.; Turnbull, J. C.; Sweeney, C.; Faloona, I. C.; Zagorac, N.; Guilderson, T. P.; Saripalli, S.; Sherwood, T.

2009-12-01

The state of California is leading the United States by enacting legislation (AB-32) to reduce greenhouse gas emissions to 1990 levels by 2020. The success of reduction efforts can be gauged with accurate emissions inventories and potentially verified with atmospheric measurements of greenhouse gases (GHGs) over time. Measurements of multiple GHGs and associated trace gas species in a specific region also provide information on emissions ratios for source apportionment. We conducted the Airborne Greenhouse Emissions Survey (AGES) campaign to determine emissions signature ratios for the sources that exist in the San Francisco Bay and Sacramento Valley areas. Specifically, we attempt to determine the emissions signatures of sources that influence ongoing measurements made at a tall-tower measurement site near Walnut Grove, CA. For two weeks in February and March of 2009, a Cessna 210 was flown throughout the Sacramento region, making continuous measurements of CO2, CH4, and CO while also sampling discrete flasks for a variety of additional tracers, including SF6, N2O, and 14C in CO2 (Δ14CO2). Flight paths were planned using wind predictions for each day to maximize sampling of sources whose emissions would also be sampled contemporaneously by the instrumentation at the Walnut Grove tower (WGC), part of the ongoing California Greenhouse Gas Emissions Measurement (CALGEM) project between NOAA/ESRL’s Carbon Cycle group and Lawrence Berkeley National Laboratory (LBNL). Flights were performed in two distinct patterns: 1) flying across a plume upwind and downwind of the Sacramento urban area, and 2) flying across the Sacramento-San Joaquin Delta from Richmond to Walnut Grove, a region consisting of natural wetlands as well as several power plants and refineries. Results show a variety of well-correlated mixing ratio signals downwind of Sacramento, documenting the urban signature emission ratios, while emissions ratios in the Delta region were more variable, likely due to the both natural and anthropogenic sources in that region. Periodic flask measurements of Δ14CO2 provide additional insight regarding the partitioning of CO2 emissions due to fossil fuel (deficient in 14C) from those of biospheric sources. A strong correlation between fossil-fuel CO2 and CO was measured downwind of Sacramento, suggesting that the continuous measurements of CO can be used to estimate a continuous profile of fossil-fuel CO2 enhancement in this region.

Distribution and Source Identification of Pb Contamination in industrial soil

NASA Astrophysics Data System (ADS)

Ko, M. S.

2017-12-01

INTRODUCTION Lead (Pb) is toxic element that induce neurotoxic effect to human, because competition of Pb and Ca in nerve system. Lead is classified as a chalophile element and galena (PbS) is the major mineral. Although the Pb is not an abundant element in nature, various anthropogenic source has been enhanced Pb enrichment in the environment after the Industrial Revolution. The representative anthropogenic sources are batteries, paint, mining, smelting, and combustion of fossil fuel. Isotope analysis widely used to identify the Pb contamination source. The Pb has four stable isotopes that are 208Pb, 207Pb, 206Pb, and 204Pb in natural. The Pb is stable isotope and the ratios maintain during physical and chemical fractionation. Therefore, variations of Pb isotope abundance and relative ratios could imply the certain Pb contamination source. In this study, distributions and isotope ratios of Pb in industrial soil were used to identify the Pb contamination source and dispersion pathways. MATERIALS AND METHODS Soil samples were collected at depth 0­-6 m from an industrial area in Korea. The collected soil samples were dried and sieved under 2 mm. Soil pH, aqua-regia digestion and TCLP carried out using sieved soil sample. The isotope analysis was carried out to determine the abundance of Pb isotope. RESULTS AND DISCUSSION The study area was developed land for promotion of industrial facilities. The study area was forest in 1980, and the satellite image show the alterations of land use with time. The variations of land use imply the possibilities of bringing in external contaminated soil. The Pb concentrations in core samples revealed higher in lower soil compare with top soil. Especially, 4 m soil sample show highest Pb concentrations that are approximately 1500 mg/kg. This result indicated that certain Pb source existed at 4 m depth. CONCLUSIONS This study investigated the distribution and source identification of Pb in industrial soil. The land use and Pb concentration at depth indicated elusive contamination event or contamination sources. In order to identify the contamination source clearly, isotope and Pb compound/mineralogy analysis are necessary.

Electrical source localization by LORETA in patients with epilepsy: Confirmation by postoperative MRI

PubMed Central

Akdeniz, Gülsüm

2016-01-01

Background: Few studies have been conducted that have compared electrical source localization (ESL) results obtained by analyzing ictal patterns in scalp electroencephalogram (EEG) with the brain areas that are found to be responsible for seizures using other brain imaging techniques. Additionally, adequate studies have not been performed to confirm the accuracy of ESL methods. Materials and Methods: In this study, ESL was conducted using LORETA (Low Resolution Brain Electromagnetic Tomography) in 9 patients with lesions apparent on magnetic resonance imaging (MRI) and in 6 patients who did not exhibit lesions on their MRIs. EEGs of patients who underwent surgery for epilepsy and had follow-ups for at least 1 year after operations were analyzed for ictal spike, rhythmic, paroxysmal fast, and obscured EEG activities. Epileptogenic zones identified in postoperative MRIs were then compared with localizations obtained by LORETA model we employed. Results: We found that brain areas determined via ESL were in concordance with resected brain areas for 13 of the 15 patients evaluated, and those 13 patients were post-operatively determined as being seizure-free. Conclusion: ESL, which is a noninvasive technique, may contribute to the correct delineation of epileptogenic zones in patients who will eventually undergo surgery to treat epilepsy, (regardless of neuroimaging status). Moreover, ESL may aid in deciding on the number and localization of intracranial electrodes to be used in patients who are candidates for invasive recording. PMID:27011626

Electrical source localization by LORETA in patients with epilepsy: Confirmation by postoperative MRI.

PubMed

Akdeniz, Gülsüm

2016-01-01

Few studies have been conducted that have compared electrical source localization (ESL) results obtained by analyzing ictal patterns in scalp electroencephalogram (EEG) with the brain areas that are found to be responsible for seizures using other brain imaging techniques. Additionally, adequate studies have not been performed to confirm the accuracy of ESL methods. In this study, ESL was conducted using LORETA (Low Resolution Brain Electromagnetic Tomography) in 9 patients with lesions apparent on magnetic resonance imaging (MRI) and in 6 patients who did not exhibit lesions on their MRIs. EEGs of patients who underwent surgery for epilepsy and had follow-ups for at least 1 year after operations were analyzed for ictal spike, rhythmic, paroxysmal fast, and obscured EEG activities. Epileptogenic zones identified in postoperative MRIs were then compared with localizations obtained by LORETA model we employed. We found that brain areas determined via ESL were in concordance with resected brain areas for 13 of the 15 patients evaluated, and those 13 patients were post-operatively determined as being seizure-free. ESL, which is a noninvasive technique, may contribute to the correct delineation of epileptogenic zones in patients who will eventually undergo surgery to treat epilepsy, (regardless of neuroimaging status). Moreover, ESL may aid in deciding on the number and localization of intracranial electrodes to be used in patients who are candidates for invasive recording.

Smartphone-based simultaneous pH and nitrite colorimetric determination for paper microfluidic devices.

PubMed

Lopez-Ruiz, Nuria; Curto, Vincenzo F; Erenas, Miguel M; Benito-Lopez, Fernando; Diamond, Dermot; Palma, Alberto J; Capitan-Vallvey, Luis F

2014-10-07

In this work, an Android application for measurement of nitrite concentration and pH determination in combination with a low-cost paper-based microfluidic device is presented. The application uses seven sensing areas, containing the corresponding immobilized reagents, to produce selective color changes when a sample solution is placed in the sampling area. Under controlled conditions of light, using the flash of the smartphone as a light source, the image captured with the built-in camera is processed using a customized algorithm for multidetection of the colored sensing areas. The developed image-processing allows reducing the influence of the light source and the positioning of the microfluidic device in the picture. Then, the H (hue) and S (saturation) coordinates of the HSV color space are extracted and related to pH and nitrite concentration, respectively. A complete characterization of the sensing elements has been carried out as well as a full description of the image analysis for detection. The results show good use of a mobile phone as an analytical instrument. For the pH, the resolution obtained is 0.04 units of pH, 0.09 of accuracy, and a mean squared error of 0.167. With regard to nitrite, 0.51% at 4.0 mg L(-1) of resolution and 0.52 mg L(-1) as the limit of detection was achieved.

Percentage entrainment of constituent loads in urban runoff, south Florida

USGS Publications Warehouse

Miller, R.A.

1985-01-01

Runoff quantity and quality data from four urban basins in south Florida were analyzed to determine the entrainment of total nitrogen, total phosphorus, total carbon, chemical oxygen demand, suspended solids, and total lead within the stormwater runoff. Land use of the homogeneously developed basins are residential (single family), highway, commercial, and apartment (multifamily). A computational procedure was used to calculate, for all storms that had water-quality data, the percentage of constituent load entrainment in specified depths of runoff. The plot of percentage of constituent load entrained as a function of runoff is termed the percentage-entrainment curve. Percentage-entrainment curves were developed for three different source areas of basin runoff: (1) the hydraulically effective impervious area, (2) the contributing area, and (3) the drainage area. With basin runoff expressed in inches over the contributing area, the depth of runoff required to remove 90 percent of the constituent load ranged from about 0.4 inch to about 1.4 inches; and to remove 80 percent, from about 0.3 to 0.9 inch. Analysis of variance, using depth of runoff from the contributing area as the response variable, showed that the factor 'basin' is statistically significant, but that the factor 'constituent' is not statistically significant in the forming of the percentage-entrainment curve. Evidently the sewerage design, whether elongated or concise in plan dictates the shape of the percentage-entrainment curve. The percentage-entrainment curves for all constituents were averaged for each basin and plotted against basin runoff for three source areas of runoff-the hydraulically effective impervious area, the contributing area, and the drainage area. The relative positions of the three curves are directly related to the relative sizes of the three source areas considered. One general percentage-entrainment curve based on runoff from the contributing area was formed by averaging across both constituents and basins. Its coordinates are: 0.25 inch of runoff for 50-percent entrainment, 0.65 inch of runoff for 80-percent entrainment, and 0.95 inch of runoff for 90-percent entrainment. The general percentage-entrainment curve based on runoff from the hydraulically effective impervious area has runoff values of 0.35, 0.95, 1.6 inches, respectively.

Determination of Moisture Content in Coke with 239Pu-Be Neutron Source and BGO Scintillation Gamma Detector

NASA Astrophysics Data System (ADS)

Grozdanov, D. N.; Aliyev, F. A.; Hramco, C.; Kopach, Yu. N.; Bystritsky, V. M.; Skoy, V. R.; Gundorin, N. A.; Ruskov, I. N.

2018-03-01

A series of experiments has been conducted at the Frank Laboratory of Neutron Physics (FLNP) of the Joint Institute for Nuclear Research (JINR) in order to study the possibility of determining the moisture content of coke using a standard neutron source. The proposed method is based on a measurement of the spectrum of prompt γ rays emitted when samples are irradiated by fast and/or thermal neutrons. The moisture content is determined from the area of the peaks of characteristic γ rays produced in the radiative capture of thermal neutrons by the proton ( E γ = 2.223 MeV) and inelastic scattering of fast neutrons by 16O (Eγ = 6.109 MeV). The 239Pu-Be neutron source (< E n > 4.5 MeV) with an intensity of 5 × 106 n/s was used to irradiate the samples under study. A scintillation detector based on a BGO crystal was used to register the characteristic γ radiation from the inelastic fast neutron scattering and slow (thermal) neutron capture. This paper presents the results of humidity measurement in the range of 2-50% [1, 2].

Using Major Elements to Determine Sources of Nitrate in Groundwater, Suffolk County, Long Island, NY

NASA Astrophysics Data System (ADS)

Munster, J.; Hanson, G.; Bokuniewicz, H.

2004-05-01

Suffolk County is the eastern most county on Long Island with an area of 2,500 square kilometers and a population of 1.4 million. Groundwater is the only source of potable water for Suffolk County. Nitrate levels have become a concern as a result of the continued eastward urbanization of Long Island since the mid 1900's. In 2003, 2% of 1000 public supply wells had greater than 10 ppm nitrogen as nitrate, 8% had 6 to 10 ppm nitrogen as nitrate and 62% of the wells were rated as susceptible to increased nitrate contamination based on land use, travel time and prevalence. Nitrogen as nitrate above 10 ppm is harmful to infants and is currently the drinking water standard of the Environmental Protection Agency. The major sources of the nitrate in the urbanized areas are most likely turf grass fertilizer and sewage from septic tank/cesspool systems and sewage treatment plants that provide only secondary treatment. Turf grass occupies about 28% of the land. Two-thirds of the houses have septic tank/cesspool systems and a majority of the sewage treatment plants discharge effluent to the groundwater. Previous investigators of the sources of nitrate in groundwater on Long Island have used 15N values of nitrate-nitrogen to identify nitrate contamination (Bleifuss et al., 2000; Flipse and Bonner, 1985; Flipse et al., 1984; Kreitler et al., 1978). However, due to overlapping source signatures, nitrogen isotopes alone were not sufficient to characterize the sources of nitrate. More recent studies have shown that major elements that accompany nitrate in the groundwater (Bleifuss et al., 2000; Elhatip et al., 2003; Trauth and Xanthopoulos, 1997) may distinguish sources of nitrate with less ambiguity. In this study samples of waste water from septic tank/cesspool systems and sewage treatment plants and samples of soil water collected below turf grass that is not fertilized, fertilized with organic fertilizer and fertilized with chemical fertilizer were analyzed for major elements. Major element data for groundwater from Suffolk County Water Authority municipal wells have been characterized as a function of capture zone land use (Source Water Assessment Project, CDM, 2003). The data for the groundwater and the waste water and the soil water were then compared. The elements Na, Mg, Cl, NO3 and SO4 proved most successful as nitrate tracers on element-element plots. There is a distinct relationship between land use and source of nitrate contamination such that ground waters sourced in: (1) low residential density areas (1 or less dwelling units per acre (DU/acre)) plot in turf grass cultivation fields (2) medium residential areas (2-10 DU/acre) and high residential areas (more than 10 DU/acre) plot as a mixture of turf grass cultivation and wastewater (3) agricultural areas plot in the turf grass cultivation field and (4) vacant or open land use plot close to average rain water compositions.

Spatial variation in anthropogenic mortality induces a source-sink system in a hunted mesopredator.

PubMed

Minnie, Liaan; Zalewski, Andrzej; Zalewska, Hanna; Kerley, Graham I H

2018-04-01

Lethal carnivore management is a prevailing strategy to reduce livestock predation. Intensity of lethal management varies according to land-use, where carnivores are more intensively hunted on farms relative to reserves. Variations in hunting intensity may result in the formation of a source-sink system where carnivores disperse from high-density to low-density areas. Few studies quantify dispersal between supposed sources and sinks-a fundamental requirement for source-sink systems. We used the black-backed jackal (Canis mesomelas) as a model to determine if heterogeneous anthropogenic mortality induces a source-sink system. We analysed 12 microsatellite loci from 554 individuals from lightly hunted and previously unhunted reserves, as well as heavily hunted livestock- and game farms. Bayesian genotype assignment showed that jackal populations displayed a hierarchical population structure. We identified two genetically distinct populations at the regional level and nine distinct subpopulations at the local level, with each cluster corresponding to distinct land-use types separated by various dispersal barriers. Migration, estimated using Bayesian multilocus genotyping, between reserves and farms was asymmetric and heterogeneous anthropogenic mortality induced source-sink dynamics via compensatory immigration. Additionally some heavily hunted populations also acted as source populations, exporting individuals to other heavily hunted populations. This indicates that heterogeneous anthropogenic mortality results in the formation of a complex series of interconnected sources and sinks. Thus, lethal management of mesopredators may not be an effective long-term strategy in reducing livestock predation, as dispersal and, more importantly, compensatory immigration may continue to affect population reduction efforts as long as dispersal from other areas persists.

Assesment of PM10 pollution episodes in a ceramic cluster (NE Spain): proposal of a new quality index for PM10, As, Cd, Ni and Pb.

PubMed

Vicente, A B; Sanfeliu, T; Jordan, M M

2012-10-15

Environmental pollution control is one of the most important goals in pollution risk assessment today. In this sense, modern and precise tools that allow scientists to evaluate, quantify and predict air pollution are of particular interest. Monitoring atmospheric particulate matter is a challenge faced by the European Union. Specific rules on this subject are being developed (Directive 2004/107/EC, Directive 2008/50/EC) in order to reduce the potential adverse effects on human health caused by air pollution. Air pollution has two sources: natural and anthropogenic. Contributions from natural sources can be assessed but cannot be controlled, while emissions from anthropogenic sources can be controlled; monitoring to reduce this latter type of pollution should therefore be carried out. In this paper, we describe an air quality evaluation in terms of levels of atmospheric particles (PM10), as outlined by European Union legislation, carried out in an industrialised Spanish coastal area over a five-year period with the purpose of comparing these values with those of other areas in the Mediterranean Basin with different weather conditions from North of Europe. The study area is in the province of Castellón. This province is a strategic area in the frame work of European Union (EU) pollution control. Approximately 80% of European ceramic tiles and ceramic frit manufacturers are concentrated in two areas, forming the so-called "ceramics clusters"; ones in Modena (Italy) and the other in Castellón. In this kind of areas, there are a lot of air pollutants from this industry then it is difficult to fulfill de European limits of PM10 so it is necessary to control the air quality in them. The seasonal differences in the number of days in which pollutant level limits were exceeded were evaluated and the sources of contamination were identified. Air quality indexes for each pollutant have been established to determine easily and clearly the quality of air breathed. Furthermore, in accordance with Directive 2008/50/EC, an Air Quality Plan is proposed to protect human health, and the environment as a whole, in the study area. General and specific corrective measures of main emission sources are provided. A strategy for air pollution management is thus presented. Copyright © 2012 Elsevier Ltd. All rights reserved.

Prospects for Pulsar Studies with the GLAST Large Area Telescope

NASA Technical Reports Server (NTRS)

Harding, Alice K.

2007-01-01

The Large Area Telescope (LAT) on the Gamma-ray Large Area Space Telescope (GLAST), due to launch in November 2007, will have unprecedented sensitivity and energy resolution for gamma-rays in the range of 30 MeV to 200 GeV. GLAST is therefore expected to provide major advances in the understanding of high-energy emission from rotation-powered p ulsars. As the only presently known galactic GeV source class, pulsar s will be one of the most important sources for study with GLAST. The main science goals of the LAT for pulsar studies include an increase in the number of detected radio-loud and radio-quiet gamma-ray pulsar s, including millisecond pulsars, giving much better statistics for e lucidating population characteristics, measurement of the high-energy spectrum and the shape of spectral cutoffs and determining pulse profiles for a variety of pulsars of different age. Further, measurement of phase-resolved spectra and energy dependent pulse profiles of the brighter pulsars should allow detailed tests of magnetospheric partic le acceleration and radiation mechanisms, by comparing data with theo retical models that have been developed. Additionally, the LAT will have the sensitivity to allow blind pulsation searches of nearly all un identified EGRET sources, to possibly uncover more radio-quiet Geming a-like pulsars.

Prospects for Pulsar Studies with the GLAST Large Area Telescope

NASA Technical Reports Server (NTRS)

Harding, Alice K.

2007-01-01

The Large Area Telescope (LAT) on the Gamma-ray Large Area Space Telescope (GLAST), due to launch in November 2007, will have unprecedented sensitivity and energy resolution for gamma-rays in the range of 30 MeV to 200 GeV. GLAST is therefore expected to provide major advances in the understanding of high-energy emission from rotation-powered pulsars. As the only presently known galactic GeV source class; pulsars will be one of the most important sources for study with GLAST. The main science goals of the LAT for pulsar studies include an increase in the number of detected radio-loud and radio-quiet gamma-ray pulsars, including millisecond pulsars, giving much better statistics for elucidating population characteristics, measurement of the high-energy spectrum and the shape of spectral cutoffs and determining pulse profiles for a variety of pulsars of different age. Further, measurement of phase-resolved spectra and energy dependent pulse profiles of the brighter pulsars should allow detailed tests of magnetospheric particle acceleration and radiation mechanisms, by comparing data with theoretical models that have been developed. Additionally, the LAT will have the sensitivity to allow blind pulsation searches of nearly all unidentified EGRET sources, to possibly uncover more radio-quiet Geminga-like pulsars.

Atmospheric mercury emissions from mine wastes and surrounding geologically enriched terrains

USGS Publications Warehouse

Gustin, M.S.; Coolbaugh, M.F.; Engle, M.A.; Fitzgerald, B.C.; Keislar, R.E.; Lindberg, S.E.; Nacht, D.M.; Quashnick, J.; Rytuba, J.J.; Sladek, C.; Zhang, H.; Zehner, R.E.

2003-01-01

Waste rock and ore associated with Hg, precious and base metal mining, and their surrounding host rocks are typically enriched in mercury relative to natural background concentrations (<0.1 ??g Hg g-1). Mercury fluxes to the atmosphere from mineralized areas can range from background rates (0-15 ng m-2 h-1) to tens of thousands of ng m-2 h-1. Mercury enriched substrate constitutes a long-term source of mercury to the global atmospheric mercury pool. Mercury emissions from substrate are influenced by light, temperature, precipitation, and substrate mercury concentration, and occur during the day and night. Light-enhanced emissions are driven by two processes: desorption of elemental mercury accumulated at the soil:air interface, and photo reduction of mercury containing phases. To determine the need for and effectiveness of regulatory controls on short-lived anthropogenic point sources the contribution of mercury from geologic non-point sources to the atmospheric mercury pool needs to be quantified. The atmospheric mercury contribution from small areas of mining disturbance with relatively high mercury concentrations are, in general, less than that from surrounding large areas of low levels of mercury enrichment. In the arid to semi-arid west-ern United States volatilization is the primary means by which mercury is released from enriched sites.

New Magnetic and Geochemical Results on Topsoils of the Mexico City Metropolitan Area

NASA Astrophysics Data System (ADS)

Martínez-Pichar, E.; Soler-Arechalde, A. M.; Morton, O.; Hernandez, E.; Lozano-Santa-Cruz, R.; Gonzalez, G.; Beramendi, L.; Urrutia-Fucugauchi, J. H.

2008-05-01

The Metropolitan Area of Mexico city is a region well known for intense industrial and commercial activity. The potential sources of the heavy metal pollutants are assumed to be petroleum processing, production of iron material, manufacturing, coal combustion, commercial and automobile exhaust. New samples were collected from industrial, roadside, residential and public parks in the urban areas around the city and added to two previous field campaigns (2003 and 2005). Localities selected for the study represent, presumably, different heavy metal pollution levels and sources. At each sampling point, the top 2 cm layer of the soil profile was collected with a stainless steel trowel and stored in a plastic bag. The elements Fe, Cu and Zn concentrations were determined by EDXRF (Philips PW1400 apparatus) on bulk- sample pressed, boric-acid backed pellets. Metal concentrations of Pb, Ni, Cr, and V were analyzed by ICP-MS with a VG Elemental PQ3 instrument. Magnetic mineralogy in bulk soil samples was investigated by low-field susceptibility using a Kappabridge KLY2. Remanent magnetizations (ARM and IRM) and Hysteresis loops of micro samples had been carried out at room temperature. Bivariate analysis on different ratios of magnetic parameters was employed to characterize the pollution sources.

Impact of a medical waste incinerator on mercury levels in lagoon fish from a small tropical island in the Western Pacific.

PubMed

Denton, Gary R W; Trianni, Michael S; Bearden, Brian G; Houk, Peter C; Starmer, John A

2011-01-01

In 2004-2005, several species of marine fish were collected for mercury (Hg) analysis from Saipan Lagoon, Saipan, Commonwealth of the Northern Mariana Islands. Relatively high concentrations were found in representatives from the Hafa Adai Beach area located some distance from known sources of Hg contamination. A follow-up investigation aimed at identifying additional land-based sources of Hg in the area was launched in early 2007. The study identified a medical waste incinerator as the primary source of Hg enrichment. The incinerator was operational for about 20 years before it was closed down by the U.S. Environmental Protection Agency (EPA) in January 2006, for multiple violations of the Clean Air Act. Stormwater runoff from this facility entered a drainage network that discharged into the ocean at the southern end of Hafa Adai Beach, about 1 km away. At the time of this investigation storm drain sediments at the coast were only marginally enriched with mercury although values some 50x above background were detected in drainage deposits a few meters down-gradient of the incinerator site. Mercury concentrations in fish from the Hafa Adai Beach area were also significantly lower than those determined in similar species 3 yr earlier. The implications of the data are briefly discussed.

Trace metals solubility in rainwater: evaluation of rainwater quality at a watershed area, Istanbul.

PubMed

Başak, Bertan; Alagha, Omar

2010-08-01

In this study, 79 bulk precipitation samples were collected at two sampling sites near Büyükçekmece Lake, one of the important drinking water sources of Istanbul, for the period of October 2001 to July 2002. The study comprised the determination of trace and toxic metals concentrations in rain water. The concentrations of the metals in this study were found to be higher than those reported by other researchers around the world. The solubility of toxic metals was found in the order of Cd>Cu>V>Zn>Ni>Pb>Cr. Solubility of metals under acidic conditions (pH<5.5) was approximately five times higher than those under neutral conditions with Cd as the most soluble metal (50% soluble). Statistical evaluations including seasonal variations, crustal enrichment factors, and correlation matrix were discussed to identify the possible sources of these pollutants. The study revealed that anthropogenic elements were highly enriched especially for Cd>Cu>Pb which were found to be highly enriched. Significant portion of Cu and Pb could be increased by the effect of local sources like cement industry in the area; however, the rest of the investigated trace metals could be brought to the sampling site by long-range transport to the Büyükçekmece Lake watershed area.

Methodology of determining soil structure in important groundwater areas: case studies in Kauvonkangas, Finnish Lapland

NASA Astrophysics Data System (ADS)

Kupila, Juho

2016-04-01

Finland is fully self-sufficient in clean groundwater and even has a capacity of exportation. There are approx. 6000 groundwater areas with a total yield of 5.4 million m3/day. Currently only 10% of this groundwater resource is in use. For the efficient and safe exploitation of these areas in the future, detailed modeling of soil structure is an important method in groundwater surveys. 3D -models improve the general knowledge of linkage between land use planning and groundwater protection. Results can be used as a base information in water supply service development and when performing the measures needed in case of environmental accidents. Also, when creating the groundwater flow models the collected information is utilized and is usually the main data source. Geological Survey of Finland has carried out soil structure studies in co-operation with authorities, municipalities and the local water suppliers. The main objectives of these projects are to determine the geological structure of groundwater area for estimating the validity of the present exclusion area, the quantity of ground water volume and recharge capability and possible risks to the groundwater. Research areas are usually under an active water supply service. Kauvonkangas groundwater area is located in the municipality of Tervola, in Southern part of Finnish Lapland. Extent of the area is 7.9 km2 and it is an important water source for the local and nearby population centers. There are two active water supply companies in the area. Field studies in the project will include general geological and hydrological mapping, soil drilling with observation pipe installation, test pumping and water sampling. Geophysical measures will play a key-role, including ground penetrating radar (GPR) and gravimetric measurements. Studies will be carried out in spring and summer 2016. The main results will be the models of the bedrock and groundwater level and main characteristics of the soil layers in the area. Results will also include the main flow directions of the groundwater. Structure models will be done with Groundhog -software. Kauvonkangas -project is funded by local water supply companies Meri-Lapin Vesi and Tervolan Vesi, Ministry of Agriculture and Forestry, and Geological Survey of Finland.

The Effect of Coastline Changes to Local Community's Social-Economic

NASA Astrophysics Data System (ADS)

Hassan, M. I.; Rahmat, N. H.

2016-09-01

The coastal area is absolutely essential for the purposes of resident, recreation, tourism, fisheries and agriculture as a source of socio-economic development of local community. Some of the activities will affect the coastline changes. Coastline changes may occur due to two main factors include natural factors and also by the factor of human activities in coastal areas. Sea level rise, erosion and sedimentation are among the factors that can contribute to the changes in the coastline naturally, while the reclamation and development in coastal areas are factors of coastline changes due to human activities. Resident area and all activities in coastal areas will provide economic resources to the residents of coastal areas. However, coastline changes occur in the coastal areas will affect socio-economic for local community. A significant effect can be seen through destruction of infrastructure, loss of land, and destroy of crops. Batu Pahat is an area with significant changes of coastline. The changes of coastline from 1985 to 2013 can be determined by using topographical maps in 1985 and satellite images where the changes images are taken in 2011 and 2013 respectively. To identify the changes of risk areas, Coastal Vulnerability Index (CVI) is used to indicate vulnerability for coastal areas. This change indirectly affects the source of income in their agricultural cash crops such as oil palm and coconut. Their crops destroyed and reduced due to impact of changes in the coastline. Identification of risk coastal areas needs to be done in order for the society and local authorities to be prepared for coastline changes.

Detection of horse allergen around a stable.

PubMed

Elfman, Lena; Brannstrom, Johan; Smedje, Greta

2008-01-01

Integrating horse stables with built-up areas may lead to conflicts. Dispersion of horse allergen may become a health risk for allergic people. The aim was to measure the dispersion of horse allergen around a stable, considering wind speed and direction and vegetation. The disturbance of staff at a workplace nearby a stable was investigated. Air sampling was performed around a stable (32 horses) at distances of 50-500 m in all directions. Sampling was done with a pump and an IOM sampler. Samples were collected at 50 points during all seasons. Horse allergen levels were determined using ELISA. Disturbance by horses was studied with a questionnaire handed to the employees in an office near the stable. The median horse allergen level at the stable entrance was 316 U/m(3), in the horse fields 40 U/m(3) and in the whole source area 16 U/m(3), which declined to <2 U/m(3) at about 50 m from the source area. Downwind of the prevailing winds low levels of horse allergen (2-4 U/m(3)) could sometimes be detected at up to 500 m. The staff, including those allergic to horses, managed to tolerate horses close to the workplace. At low winds horse allergen spread in ambient air about 50 m from the stable and horse fields. At higher winds low allergen levels were sometimes found in open areas up to 500 m from the source area. These levels were similar to those found in the office after moving away from the stable area. The employees did not report more symptoms of allergy or asthma while working close to the stable compared to after the move. 2007 S. Karger AG, Basel

Atomic Oxygen Durability Evaluation of Protected Polymers Using Thermal Energy Plasma Systems

NASA Technical Reports Server (NTRS)

Banks, Bruce A.; Rutledge, Sharon K.; Degroh, Kim K.; Stidham, Curtis R.; Gebauer, Linda; Lamoreaux, Cynthia M.

1995-01-01

The durability evaluation of protected polymers intended for use in low Earth orbit (LEO) has necessitated the use of large-area, high-fluence, atomic oxygen exposure systems. Two thermal energy atomic oxygen exposure systems which are frequently used for such evaluations are radio frequency (RF) plasma ashers and electron cyclotron resonance plasma sources. Plasma source testing practices such as ample preparation, effective fluence prediction, atomic oxygen flux determination, erosion measurement, operational considerations, and erosion yield measurements are presented. Issues which influence the prediction of in-space durability based on ground laboratory thermal energy plasma system testing are also addressed.

Detailed study of irrigation drainage in and near wildlife management areas, west-central Nevada, 1987-90; Part C, Summary of irrigation-drainage effects on water quality, bottom sediment, and biota

USGS Publications Warehouse

Hoffman, Ray J.

1993-01-01

This report presents a summary of the detailed scientific study of Stillwater Wildlife Management Area and other nearby wetlands in west-central Nevada during 1987-90. The work was funded by the National Irrigation Water Quality Program of the U.S. Department of the Interior with the overall objectives of determining (1) the extent, magnitude, and effects of selected water-quality constituents associated with irrigation drainage on fish, wildlife, and human health, and (2) the sources and exposure pathways that cause contamination where adverse effects are documented. Much of the information in this report was summarized from two previously published interpretive reports that were completed to fulfill study objectives. Where applicable, data for the study area from other published sources also were utilized. The results of these studies indicate that the aquatic biota in natural wetlands of the Carson Desert are adversely affected by hydrological and geochemical sources and processes in the Newlands Irrigation Project area. Reactions between water and naturally occurring minerals in the shallow alluvial aquifer increase concentrations of potentially toxic constituents in ground water that eventually enters the wetlands. Once in the wetlands, these constituents are furhter concentrated by evaporation and transpiration. Water from some agricultural drains that enter Stillwater WMA was acutely toxic to aquatic organisms. The drains in the agricultural areas, which eventually discharge to the wetlands, were also implicated as sites of uptake of selenium and mercury by aquatic organisms.

Polycyclic Aromatic Hydrocarbons and Esophageal Squamous Cell Carcinoma-A Review

PubMed Central

Roshandel, Gholamreza; Semnani, Shahryar; Malekzadeh, Reza; Dawsey, Sanford M.

2018-01-01

Esophageal cancer (EC) is the 8th most common cancer and the 6th most frequent cause of cancer mortality worldwide. Esophageal squamous cell carcinoma (ESCC) is the most common type of EC. Exposure to polycyclic aromatic hydrocarbons (PAHs) has been suggested as a risk factor for developing ESCC. In this paper we will review different aspects of the relationship between PAH exposure and ESCC. PAHs are a group of compounds that are formed by incomplete combustion of organic matter. Studies in humans have shown an association between PAH exposure and development of ESCC in many populations. The results of a recent case-control study in a high risk population in northeastern Iran showed a dramatic dose-response relationship between PAH content in non-tumor esophageal tissue (the target tissue for esophageal carcinogenesis) and ESCC case status, consistent with a causal role for PAH exposure in the pathogenesis of ESCC. Identifying the main sources of exposure to PAHs may be the first and most important step in designing appropriate PAH-reduction interventions for controlling ESCC, especially in high risk areas. Coal smoke and drinking mate have been suggested as important modifiable sources of PAH exposure in China and Brazil, respectively. But the primary source of exposure to PAHs in other high risk areas for ESCC, such as northeastern Iran, has not yet been identified. Thus, environmental studies to determining important sources of PAH exposure should be considered as a high priority in future research projects in these areas. PMID:23102250

Early outbreak detection by linking health advice line calls to water distribution areas retrospectively demonstrated in a large waterborne outbreak of cryptosporidiosis in Sweden.

PubMed

Bjelkmar, Pär; Hansen, Anette; Schönning, Caroline; Bergström, Jakob; Löfdahl, Margareta; Lebbad, Marianne; Wallensten, Anders; Allestam, Görel; Stenmark, Stephan; Lindh, Johan

2017-04-18

In the winter and spring of 2011 a large outbreak of cryptosporidiosis occurred in Skellefteå municipality, Sweden. This study summarizes the outbreak investigation in terms of outbreak size, duration, clinical characteristics, possible source(s) and the potential for earlier detection using calls to a health advice line. The investigation included two epidemiological questionnaires and microbial analysis of samples from patients, water and other environmental sources. In addition, a retrospective study based on phone calls to a health advice line was performed by comparing patterns of phone calls between different water distribution areas. Our analyses showed that approximately 18,500 individuals were affected by a waterborne outbreak of cryptosporidiosis in Skellefteå in 2011. This makes it the second largest outbreak of cryptosporidiosis in Europe to date. Cryptosporidium hominis oocysts of subtype IbA10G2 were found in patient and sewage samples, but not in raw water or in drinking water, and the initial contamination source could not be determined. The outbreak went unnoticed to authorities for several months. The analysis of the calls to the health advice line provides strong indications early in the outbreak that it was linked to a particular water treatment plant. We conclude that an earlier detection of the outbreak by linking calls to a health advice line to water distribution areas could have limited the outbreak substantially.

40 CFR Table 1 to Subpart Zzzzzz... - Applicability of General Provisions to Aluminum, Copper, and Other Nonferrous Foundries Area Sources

Code of Federal Regulations, 2010 CFR

2010-07-01

... Aluminum, Copper, and Other Nonferrous Foundries Area Sources 1 Table 1 to Subpart ZZZZZZ of Part 63... Standards for Hazardous Air Pollutants: Area Source Standards for Aluminum, Copper, and Other Nonferrous... Provisions to Aluminum, Copper, and Other Nonferrous Foundries Area Sources As required in § 63.11555, “What...

40 CFR Table 1 to Subpart Zzzzzz... - Applicability of General Provisions to Aluminum, Copper, and Other Nonferrous Foundries Area Sources

Code of Federal Regulations, 2011 CFR

2011-07-01

... Aluminum, Copper, and Other Nonferrous Foundries Area Sources 1 Table 1 to Subpart ZZZZZZ of Part 63... Standards for Hazardous Air Pollutants: Area Source Standards for Aluminum, Copper, and Other Nonferrous... Provisions to Aluminum, Copper, and Other Nonferrous Foundries Area Sources As required in § 63.11555, “What...

Determinants of Paracentrotus lividus sea urchin recruitment under oligotrophic conditions: Implications for conservation management.

PubMed

Oliva, Silvia; Farina, Simone; Pinna, Stefania; Guala, Ivan; Agnetta, Davide; Ariotti, Pierre Antoine; Mura, Francesco; Ceccherelli, Giulia

2016-06-01

Sea urchins may deeply shape the structure of macrophyte-dominated communities and require the implementation of sustainable management strategies. In the Mediterranean, the identification of the major recruitment determinants of the keystone sea urchin species Paracentrotus lividus is required, so that source areas of the populations can be identified and exploitation or programmed harvesting can be spatially managed. In this study a collection of eight possible determinants, these encompassing both the biotic (larvae, adult sea urchins, fish, encrusting coralline algae, habitat type and spatial arrangement of habitats) and abiotic (substrate complexity and nutritional status) realms was considered at different spatial scales (site, area, transect and quadrat). Data from a survey including sites subject to different levels of human influence (i.e. from urbanized to protected areas), but all corresponding to an oligotrophic and low-populated region were fitted by means of a generalized linear mixed model. Despite the extensive sampling effort of benthic quadrats, an overall paucity of recruits was found, recruits being aggregated in a very small number of quadrats and in few areas. The analysis of data detected substrate complexity, and adult sea urchin and predatory fish abundances as the momentous determinants of Paracentrotus lividus recruitment. Possible mechanisms of influence are discussed beyond the implications of conservation management. Copyright © 2016 Elsevier Ltd. All rights reserved.

Comparison of fipronil sources in North Carolina surface water ...

EPA Pesticide Factsheets

Fipronil is a phenylpyrazole insecticide that is widely used in residential and agricultural settings to control ants, roaches, termites, and other pests. Fipronil and its transformation products have been found in a variety of environmental matrices, but the source[s] which makes the greatest contribution to fipronil in surface water has yet to be determined. A sampling effort designed to prioritize known fipronil inputs (golf courses, residential areas, biosolids application sites and wastewater facilities) was conducted in North Carolina to learn more about the origins of fipronil in surface water. High resolution mass spectrometry (HRMS) analysis indicated that fipronil and its known derivatives were routinely present in all samples, but concentrations were substantially elevated near wastewater treatment plant outfalls (range 10–500 ng/L combined), suggesting that they predominate as environmental sources. Corresponding recycled wastewater samples, which were treated with NaOCl for disinfection, showed disappearance of fipronil and all known degradates. HRMS and nuclear magnetic resonance (NMR) analysis techniques were used to determine that all fipronil-related compounds are oxidized to a previously unidentified fipronil sulfone chloramine species in recycled wastewater. The implications of the presence of a new fipronil-related compound in recycled wastewater need to be considered. Journal Article Highlights • The most important sources of fipronil in

Poster - 11: Radiation barrier thickness calculations for the GammaPod

DOE Office of Scientific and Technical Information (OSTI.GOV)

La Russa, Daniel; Vandervoort, Eric; Wilkins, Davi

A consortium of radiotherapy centers in North America is in the process of evaluating a novel new {sup 60}Co teletherapy device, called the GammaPod™ (Xcision Medical Systems, Columbia Maryland), designed specifically for breast SBRT. The GammaPod consists of 36 collimated {sup 60}Co sources with a total activity of 4320 Ci. The sources are housed in a hemispherical source carrier that rotates during treatment to produce a cylindrically symmetric cone of primary beam spanning 16° – 54° degrees from the horizontal. This unique beam geometry presents challenges when designing or evaluating room shielding for the purposes of meeting regulatory requirements, andmore » for ensuring the safety of staff and the public in surrounding areas. Conventional methods for calculating radiation barrier thicknesses have been adapted so that barrier transmission factors for the GammaPod can be determined from a few relevant distances and characteristics of the primary beam. Simple formalisms have been determined for estimating shielding requirements for primary radiation (with a rotating and non-rotating source carrier), patient-scattered radiation, and leakage radiation. When making worst case assumptions, it was found that conventional barrier thicknesses associated with linac treatment suites are sufficient for shielding all sources of radiation from the GammaPod.« less

Mesozoic non-marine petroleum source rocks determined by palynomorphs in the Tarim Basin, Xinjiang, northwestern China

USGS Publications Warehouse

Jiang, D.-X.; Wang, Y.-D.; Robbins, E.I.; Wei, J.; Tian, N.

2008-01-01

The Tarim Basin in Northwest China hosts petroleum reservoirs of Cambrian, Ordovician, Carboniferous, Triassic, Jurassic, Cretaceous and Tertiary ages. The sedimentary thickness in the basin reaches about 15 km and with an area of 560000 km2, the basin is expected to contain giant oil and gas fields. It is therefore important to determine the ages and depositional environments of the petroleum source rocks. For prospective evaluation and exploration of petroleum, palynological investigations were carried out on 38 crude oil samples collected from 22 petroleum reservoirs in the Tarim Basin and on additionally 56 potential source rock samples from the same basin. In total, 173 species of spores and pollen referred to 80 genera, and 27 species of algae and fungi referred to 16 genera were identified from the non-marine Mesozoic sources. By correlating the palynormorph assemblages in the crude oil samples with those in the potential source rocks, the Triassic and Jurassic petroleum source rocks were identified. Furthermore, the palynofloras in the petroleum provide evidence for interpretation of the depositional environments of the petroleum source rocks. The affinity of the miospores indicates that the petroleum source rocks were formed in swamps in brackish to lacustrine depositional environments under warm and humid climatic conditions. The palynomorphs in the crude oils provide further information about passage and route of petroleum migration, which is significant for interpreting petroleum migration mechanisms. Additionally, the thermal alternation index (TAI) based on miospores indicates that the Triassic and Jurassic deposits in the Tarim Basin are mature petroleum source rocks. ?? Cambridge University Press 2008.

Computing payment for ecosystem services in watersheds: an analysis of the Middle Route Project of South-to-North Water Diversion in China.

PubMed

Dong, Zhengju; Yan, Yan; Duan, Jing; Fu, Xiao; Zhou, Qingrong; Huang, Xiang; Zhu, Xiangen; Zhao, Jingzhu

2011-01-01

Payment for ecosystem services (PES) has attracted considerable attention as an economic incentive for promoting natural resource management recently. As emphasis has been placed on using the incentive-based mechanism by the central government, rapid progress on PES research and practice has been achieved. However PES still faces many difficulties. A key issue is the lack of a fully-fledged theory and method to clearly define the design scope, accounting and feasibility of PES criteria. An improved watershed criteria model was developed in light of research on PES practices in China, investigations on the water source area for the Middle Route Project of South-to-North Water Diversion and ecosystem services outflows theory. The basic principle of assessment is the direct and opportunity cost for ecological conservation and environmental protection in the water source area deduct nationally-financed PES and internal effect. Then the scope and the criteria methods were determined, and internal effect was put forward to define benefits brought from water source area. Finally, Shiyan City, which is the main water source area for the Project of Water Diversion, was analyzed by this model and its payment was calculated. The results showed that: (1) during 2003-2050, the total direct cost and opportunity cost would reach up to 262.70 billion and 256.33 billion Chinese Yuan (CNY, 2000 constant prices), i.e., 50.61% and 49.38% of total cost, respectively; (2) Shiyan City would gain 0.23, 0.06 and 0.03 CNY/m3 in 2014-2020, 2021-2030, and 2031-2050, respectively.

Assessing field vulnerability to phosphorus loss in Beijing agricultural area using Revised Field Phosphorus Ranking Scheme.

PubMed

Li, Qi; Chen, Li-ding; Qi, Xin; Zhang, Xin-yu; Ma, Yan; Fu, Bo-jie

2007-01-01

Guanting Reservoir, one of the drinking water supply sources of Beijing, suffers from water eutrophication. It is mainly supplied by Guishui River. Thus, to investigate the reasons of phosphorus (P) loss and improve the P management strategies in Guishui River watershed are important for the safety of drinking water in this region. In this study, a Revised Field P Ranking Scheme (PRS) was developed to reflect the field vulnerability of P loss at the field scale based on the Field PRS. In this new scheme, six factors are included, and each one was assigned a relative weight and a determination method. The affecting factors were classified into transport factors and source factors, and, the standards of environmental quality on surface water and soil erosion classification and degradation of the China were used in this scheme. By the new scheme, thirty-four fields in the Guishui River were categorized as "low", "medium" or "high" potential for P loss into the runoff. The results showed that the P loss risks of orchard and vegetable fields were higher than that of corn and soybean fields. The source factors were the main factors to affect P loss from the study area. In the study area, controlling P input and improving P usage efficiency are critical to decrease P loss. Based on the results, it was suggested that more attention should be paid on the fields of vegetable and orchard since they have extremely high usage rate of P and high soil test of P. Compared with P surplus by field measurements, the Revised Field PRS was more suitable for reflecting the characteristics of fields, and had higher potential capacity to identify critical source areas of P loss than PRS.

Evaluation of the performance of small diode pumped UV solid state (DPSS) Nd:YAG lasers as new radiation sources for atmospheric pressure laser ionization mass spectrometry (APLI-MS).

PubMed

Kersten, Hendrik; Lorenz, Matthias; Brockmann, Klaus J; Benter, Thorsten

2011-06-01

The performance of a KrF* bench top excimer laser and a compact diode pumped UV solid state (DPSS) Nd:YAG laser as photo-ionizing source in LC-APLI MS is compared. The commonly applied bench-top excimer laser, operating at 248 nm, provides power densities of the order of low MW/cm(2) on an illuminated area of 0.5 cm(2) (8 mJ/pulse, 5 ns pulse duration, beam waist area 0.5 cm(2), 3 MW/cm(2)). The DPSS laser, operating at 266 nm, provides higher power densities, however, on a two orders of magnitude smaller illuminated area (60 μJ/pulse, 1 ns pulse duration, beam waist area 2 × 10(-3) cm(2), 30 MW/cm(2)). In a common LC-APLI MS setup with direct infusion of a 10 nM pyrene solution, the DPSS laser yields a significantly smaller ion signal (0.9%) and signal to noise ratio (1.4%) compared with the excimer laser. With respect to the determined low detection limits (LODs) for PAHs of 0.1 fmol using an excimer laser, LODs in DPSS laser LC-APLI MS in the low pmol regime are expected. The advantages of the DPSS laser with respect to applicability (size, cost, simplicity) may render this light source the preferred one for APLI applications not focusing on ultimately high sensitivities. Furthermore, the impact of adjustable ion source parameters on the performance of both laser systems is discussed in terms of the spatial sensitivity distribution described by the distribution of ion acceptance (DIA) measurements. Perspectives concerning the impact on future APLI-MS applications are given.

Distribution, fate and risk assessment of PAHs in water and sediments from an aquaculture- and shipping-impacted subtropical lake, China.

PubMed

Zeng, Qingfei; Jeppesen, Erik; Gu, Xiaohong; Mao, Zhigang; Chen, Huihui

2018-06-01

The spatial-temporal distribution of polycyclic aromatic hydrocarbons (PAHs), their source, and potential health risks were determined in overlying water and surface sediments from Chinese Lake Guchenghu, adjacent commercial mitten crab ponds and the connected Wushen Canal to assess the contamination profile of the area. The total PAHs concentrations in sediment and water were 86.7-1790 ng g -1 dry weight (dw) and 184-365 ng L -1 in summer and 184-3140 ng g -1 dw and 410-1160 ng L -1 in winter. Two- and 3-ring PAHs were the predominant compounds in water, while PAHs with 4-6 rings dominated in the sediment at both upstream and downstream sites. PAHs concentrations in water and sediment correlated significantly. Diagnostic ratios and positive matrix factorization (PMF) analyses indicated a strong influence of pyrogenic sources, principally biomass combustion and vehicle emission, on the concentrations of PAHs. The distribution, source identification, and mean effects range median quotients (mERMQ) analyses suggested that the most contaminated area was located downstream and upstream of the Wushen Canal, followed by Lake Guchenghu and a commercial crab pond area. From an ecological point of view, PAHs posed a potential risk to drinking water sources as the concentrations exceeded the guideline value of 0.05 μg L -1 . The risk posed by sediment PAHs appeared to be low except for the downstream sites, which showed a low to medium ecotoxicological risk. The total incremental lifetime cancer risks ranged between 10 -7 and 10 -5 , indicating a potential health risk for the local population when exposed to sediment from the area. Copyright © 2018 Elsevier Ltd. All rights reserved.

235U Holdup Measurements in Three 321-M Exhaust HEPA Banks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dewberry, R

2005-02-24

The Analytical Development Section of Savannah River National Laboratory (SRNL) was requested by the Facilities Disposition Division to determine the holdup of enriched uranium in the 321-M facility as part of an overall deactivation project of the facility. The 321-M facility was used to fabricate enriched uranium fuel assemblies, lithium-aluminum target tubes, neptunium assemblies, and miscellaneous components for the production reactors. The results of the holdup assays are essential for determining compliance with the Waste Acceptance Criteria, Material Control & Accountability, and to meet criticality safety controls. This report covers holdup measurements of uranium residue in three HEPA filter exhaustmore » banks of the 321-M facility. Each of the exhaust banks has dimensions near 7' x 14' x 4' and represents a complex holdup problem. A portable HPGe detector and EG&G Dart system that contains the high voltage power supply and signal processing electronics were used to determine highly enriched uranium (HEU) holdup. A personal computer with Gamma-Vision software was used to control the Dart MCA and to provide space to store and manipulate multiple 4096-channel {gamma}-ray spectra. Some acquisitions were performed with the portable detector configured to a Canberra Inspector using NDA2000 acquisition and analysis software. Our results for each component uses a mixture of redundant point source and area source acquisitions that yielded HEU contents in the range of 2-10 grams. This report discusses the methodology, non-destructive assay (NDA) measurements, assumptions, and results of the uranium holdup in these items. This report includes use of transmission-corrected assay as well as correction for contributions from secondary area sources.« less

Response Variability in Commercial MOSFET SEE Qualification

DOE PAGES

George, J. S.; Clymer, D. A.; Turflinger, T. L.; ...

2016-12-01

Single-event effects (SEE) evaluation of five different part types of next generation, commercial trench MOSFETs indicates large part-to-part variation in determining a safe operating area (SOA) for drain-source voltage (V DS) following a test campaign that exposed >50 samples per part type to heavy ions. These results suggest a determination of a SOA using small sample sizes may fail to capture the full extent of the part-to-part variability. An example method is discussed for establishing a Safe Operating Area using a one-sided statistical tolerance limit based on the number of test samples. Finally, burn-in is shown to be a criticalmore » factor in reducing part-to-part variation in part response. Implications for radiation qualification requirements are also explored.« less

Response Variability in Commercial MOSFET SEE Qualification

DOE Office of Scientific and Technical Information (OSTI.GOV)

George, J. S.; Clymer, D. A.; Turflinger, T. L.

Single-event effects (SEE) evaluation of five different part types of next generation, commercial trench MOSFETs indicates large part-to-part variation in determining a safe operating area (SOA) for drain-source voltage (V DS) following a test campaign that exposed >50 samples per part type to heavy ions. These results suggest a determination of a SOA using small sample sizes may fail to capture the full extent of the part-to-part variability. An example method is discussed for establishing a Safe Operating Area using a one-sided statistical tolerance limit based on the number of test samples. Finally, burn-in is shown to be a criticalmore » factor in reducing part-to-part variation in part response. Implications for radiation qualification requirements are also explored.« less

Contamination source apportionment and health risk assessment of heavy metals in soil around municipal solid waste incinerator: A case study in North China.

PubMed

Ma, Wenchao; Tai, Lingyu; Qiao, Zhi; Zhong, Lei; Wang, Zhen; Fu, Kaixuan; Chen, Guanyi

2018-08-01

Few studies have comprehensively taken into account the source apportionment and human health risk of soil heavy metals in the vicinity of municipal solid waste incinerator (MSWI) in high population density area. In this study, 8 elements (Cr, Pb, Cu, Ni, Zn, Cd, Hg, and As) in fly ash, soil samples from different functional areas and vegetables collected surrounding the MSWI in North China were determined. The single pollution index, integrated Nemerow pollution index, principal component analysis (PCA), absolute principle component score-multiple linear regression (APCS-MLR) model and dose-response model were used in this study. The results showed that the soils around the MSWI were moderately polluted by Cu, Pb, Zn, and Hg, and heavily polluted by As and Cd. MSWI had a significant influence on the distribution of soil heavy metals in different distances from MSWI. The source apportionment results showed that MSWI, natural source, industrial discharges and coal combustion were the four major potential sources for heavy metals in the soils, with the contributions of 36.08%, 29.57%, 10.07%, and 4.55%, respectively. MSWI had a major impact on Zn, Cu, Pb, Cd, and Hg contamination in soil. The non-carcinogenic risk and carcinogenic risk posed by soil heavy metals surrounding the MSWI were unacceptable. The soil heavy metals concentrations and health risks in different functional areas were distinct. MSWI was the predominate source of non-carcinogenic risk with the average contribution rate of 36.99% and carcinogenic risk to adult male, adult female and children with 4.23×10 -4 , 4.57×10 -4 , and 1.41×10 -4 respectively, implying that the impact of MSWI on human health was apparent. This study provided a new insight for the source apportionment and health risk assessment of soil heavy metals in the vicinity of MSWI. Copyright © 2018. Published by Elsevier B.V.

Heavy metal transport in large river systems: heavy metal emissions and loads in the Rhine and Elbe river basins

NASA Astrophysics Data System (ADS)

Vink, Rona; Behrendt, Horst

2002-11-01

Pollutant transport and management in the Rhine and Elbe basins is still of international concern, since certain target levels set by the international committees for protection of both rivers have not been reached. The analysis of the chain of emissions of point and diffuse sources to river loads will provide policy makers with a tool for effective management of river basins. The analysis of large river basins such as the Elbe and Rhine requires information on the spatial and temporal characteristics of both emissions and physical information of the entire river basin. In this paper, an analysis has been made of heavy metal emissions from various point and diffuse sources in the Rhine and Elbe drainage areas. Different point and diffuse pathways are considered in the model, such as inputs from industry, wastewater treatment plants, urban areas, erosion, groundwater, atmospheric deposition, tile drainage, and runoff. In most cases the measured heavy metal loads at monitoring stations are lower than the sum of the heavy metal emissions. This behaviour in large river systems can largely be explained by retention processes (e.g. sedimentation) and is dependent on the specific runoff of a catchment. Independent of the method used to estimate emissions, the source apportionment analysis of observed loads was used to determine the share of point and diffuse sources in the heavy metal load at a monitoring station by establishing a discharge dependency. The results from both the emission analysis and the source apportionment analysis of observed loads were compared and gave similar results. Between 51% (for Hg) and 74% (for Pb) of the total transport in the Elbe basin is supplied by inputs from diffuse sources. In the Rhine basin diffuse source inputs dominate the total transport and deliver more than 70% of the total transport. The diffuse hydrological pathways with the highest share are erosion and urban areas.

INEEL Source Water Assessment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sehlke, Gerald

2003-03-01

The Idaho National Engineering and Environmental Laboratory (INEEL) covers approximately 890 mi2 and includes 12 public water systems that must be evaluated for Source water protection purposes under the Safe Drinking Water Act. Because of its size and location, six watersheds and five aquifers could potentially affect the INEEL’s drinking water sources. Based on a preliminary evaluation of the available information, it was determined that the Big Lost River, Birch Creek, and Little Lost River Watersheds and the eastern Snake River Plain Aquifer needed to be assessed. These watersheds were delineated using the United States Geologic Survey’s Hydrological Unit scheme.more » Well capture zones were originally estimated using the RESSQC module of the Environmental Protection Agency’s Well Head Protection Area model, and the initial modeling assumptions and results were checked by running several scenarios using Modflow modeling. After a technical review, the resulting capture zones were expanded to account for the uncertainties associated with changing groundwater flow directions, a thick vadose zone, and other data uncertainties. Finally, all well capture zones at a given facility were merged to a single wellhead protection area at each facility. A contaminant source inventory was conducted, and the results were integrated with the well capture zones, watershed and aquifer information, and facility information using geographic information system technology to complete the INEEL’s Source Water Assessment. Of the INEEL’s 12 public water systems, three systems rated as low susceptibility (EBR-I, Main Gate, and Gun Range), and the remainder rated as moderate susceptibility. No INEEL public water system rated as high susceptibility. We are using this information to develop a source water management plan from which we will subsequently implement an INEEL-wide source water management program. The results are a very robust set of wellhead protection areas that will protect the INEEL’s public water systems yet not too conservative to inhibit the INEEL from carrying out its missions.« less

The Idaho National Engineering and Environmental Laboratory Source Water Assessment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sehlke, G.

2003-03-17

The Idaho National Engineering and Environmental Laboratory (INEEL) covers approximately 890 square miles and includes 12 public water systems that must be evaluated for Source water protection purposes under the Safe Drinking Water Act. Because of its size and location, six watersheds and five aquifers could potentially affect the INEEL's drinking water sources. Based on a preliminary evaluation of the available information, it was determined that the Big Lost River, Birch Creek, and Little Lost River Watersheds and the eastern Snake River Plain Aquifer needed to be assessed. These watersheds were delineated using the United States Geologic Survey's Hydrological Unitmore » scheme. Well capture zones were originally estimated using the RESSQC module of the Environmental Protection Agency's Well Head Protection Area model, and the initial modeling assumptions and results were checked by running several scenarios using Modflow modeling. After a technical review, the resulting capture zones were expanded to account for the uncertainties associated with changing groundwater flow directions, a this vadose zone, and other data uncertainties. Finally, all well capture zones at a given facility were merged to a single wellhead protection area at each facility. A contaminant source inventory was conducted, and the results were integrated with the well capture zones, watershed and aquifer information, and facility information using geographic information system technology to complete the INEEL's Source Water Assessment. Of the INEEL's 12 public water systems, three systems rated as low susceptibility (EBR-1, Main Gate, and Gun Range), and the remainder rated as moderate susceptibility. No INEEL public water system rated as high susceptibility. We are using this information to develop a source water management plan from which we will subsequently implement an INEEL-wide source water management program. The results are a very robust set of wellhead protection areas that will protect the INEEL's public water systems yet not too conservative to inhibit the INEEL from carrying out its missions.« less

Using portable X-ray fluorescence spectrometry and GIS to assess environmental risk and identify sources of trace metals in soils of peri-urban areas in the Yangtze Delta region, China.

PubMed

Ran, Jing; Wang, Dejian; Wang, Can; Zhang, Gang; Yao, Lipeng

2014-08-01

Portable X-ray fluorescence (PXRF) spectrometry may be very suitable for a fast and effective environmental assessment and source identification of trace metals in soils. In this study, topsoils (0-10 cm) at 139 sites were in situ scanned for total trace metals (Cr, Cu, Ni, Pb and Zn) and arsenic concentrations by PXRF in a typical town in Yangtze Delta region of Jiangsu province, China. To validate the utility of PXRF, 53 samples were collected from the scanning sites for the determination of selected trace metals using conventional methods. Based on trace metal concentrations detected by in situ PXRF, the contamination extent and sources of trace metals were studied via geo-accumulation index, multivariate analysis and geostatistics. The trace metal concentrations determined by PXRF were similar to those obtained via conventional chemical analysis. The median concentration of As, Cr, Cu, Ni, Pb and Zn in soils were 10.8, 56.4, 41.5, 43.5, 33.5, and 77.7 mg kg(-1), respectively. The distribution patterns of Cr, Cu, Ni, Pb, and Zn were mostly affected by anthropogenic sources, while As was mainly derived from lithogenic sources. Overall, PXRF has been successfully applied to contamination assessment and source identification of trace metals in soils.

Testing the seismology-based landquake monitoring system

NASA Astrophysics Data System (ADS)

Chao, Wei-An

2016-04-01

I have developed a real-time landquake monitoring system (RLMs), which monitor large-scale landquake activities in the Taiwan using real-time seismic network of Broadband Array in Taiwan for Seismology (BATS). The RLM system applies a grid-based general source inversion (GSI) technique to obtain the preliminary source location and force mechanism. A 2-D virtual source-grid on the Taiwan Island is created with an interval of 0.2° in both latitude and longitude. The depth of each grid point is fixed on the free surface topography. A database is stored on the hard disk for the synthetics, which are obtained using Green's functions computed by the propagator matrix approach for 1-D average velocity model, at all stations from each virtual source-grid due to nine elementary source components: six elementary moment tensors and three orthogonal (north, east and vertical) single-forces. Offline RLM system was carried out for events detected in previous studies. An important aspect of the RLM system is the implementation of GSI approach for different source types (e.g., full moment tensor, double couple faulting, and explosion source) by the grid search through the 2-D virtual source to automatically identify landquake event based on the improvement in waveform fitness and evaluate the best-fit solution in the monitoring area. With this approach, not only the force mechanisms but also the event occurrence time and location can be obtained simultaneously about 6-8 min after an occurrence of an event. To improve the insufficient accuracy of GSI-determined lotion, I further conduct a landquake epicenter determination (LED) method that maximizes the coherency of the high-frequency (1-3 Hz) horizontal envelope functions to determine the final source location. With good knowledge about the source location, I perform landquake force history (LFH) inversion to investigate the source dynamics (e.g., trajectory) for the relatively large-sized landquake event. With providing aforementioned source information in real-time, the government and emergency response agencies have sufficient reaction time for rapid assessment and response to landquake hazards. Since 2016, the RLM system has operated online.

Rural People and Their Resources: North-Central New Mexico.

ERIC Educational Resources Information Center

Taylor, Marlowe M.

The general objective of a study conducted in the 1950's was to describe the physical and human resources of the rural areas in north-central New Mexico. The specific objectives were (1) to inventory and classify the land, labor, and capital resources, (2) to determine levels and sources of incomes of these households, and (3) to appraise some of…

Disturbance to the population due to flight operations at landing fields. Questionnaire on community reaction to non-commercial and sporting aviation

NASA Technical Reports Server (NTRS)

Rohrmann, B.

1981-01-01

A field study was undertaken to determine the Sociopsychological effects of air traffic noise experienced by residents of areas near small sporting aviation fields. A questionaire was prepared which includes questions on flight restriction measures, on attitudes which moderate annoyance and on comparisons with other noise sources, etc.

Contingency Pest and Vector Surveillance

DTIC Science & Technology

2013-11-01

Baseline Survey - conducted to determine the types of vectors and pests occurring in the area of operations, their respective breeding sites or...source habitat, and seasonal activity patterns. Operational Survey - data collected in an operational survey are used specifically to aid pest...management personnel in making decisions on when to start or stop control measures. Operational survey data is compared to baseline data and the

Issues concerning centralized versus decentralized power deployment

NASA Technical Reports Server (NTRS)

Metcalf, Kenneth J.; Harty, Richard B.; Robin, James F.

1991-01-01

The results of a study of proposed lunar base architectures to identify issues concerning centralized and decentralized power system deployment options are presented. The power system consists of the energy producing system (power plant), the power conditioning components used to convert the generated power into the form desired for transmission, the transmission lines that conduct this power from the power sources to the loads, and the primary power conditioning hardware located at the user end. Three power system architectures, centralized, hybrid, and decentralized, were evaluated during the course of this study. Candidate power sources were characterized with respect to mass and radiator area. Two electrical models were created for each architecture to identify the preferred method of power transmission, dc or ac. Each model allowed the transmission voltage level to be varied at assess the impact on power system mass. The ac power system models also permitted the transmission line configurations and placements to determine the best conductor construction and installation location. Key parameters used to evaluate each configuration were power source and power conditioning component efficiencies, masses, and radiator areas; transmission line masses and operating temperatures; and total system mass.

Role of zircon in tracing crustal growth and recycling

NASA Astrophysics Data System (ADS)

Compston, W.; Williams, I. S.; Armstrong, R. A.; Claoue-Long, J. C.; Kinny, P. D.; Foster, J. J.; Kroener, A.; Pidgeon, R. T.; Myers, J. S.

Single crystal ion probe ages of zircons is discussed, which allow much better time resolution compared to other geochronological methods, although the technique is not without problems. Rocks from two areas that contain composite zircon populations, including true magmatic zircons as well as a variety of xenocrystic types are described. It is often difficult to distinguish these; xenocrystic zircons, for example, cannot always be identified on the basis of morphology alone. Additional evidence is needed before making age interpretations. Evidence is also presented of zircon growth long after the original time of crystallization, in some cases apparently at temperatures less than 300 C. The spectacular discovery of 4.1 to 4.2 Ga detrital zircons in metaquartzites from the Mount Narryer area of Western Australia is described. Similar zircons with ages as old as 4276 Ma have been found in the nearby Jack Hills area. The source areas or parent lithologies of these zircons have not yet been determined, but the author expects that they may be unrecognized or buried antecedents of the K rich Narryer gneisses. U or Th concentrations of zircon cannot be used to discriminate between felsic and mafic source rocks.

Source parameters of a M4.8 and its accompanying repeating earthquakes off Kamaishi, NE Japan: Implications for the hierarchical structure of asperities and earthquake cycle

USGS Publications Warehouse

Uchida, N.; Matsuzawa, T.; Ellsworth, W.L.; Imanishi, K.; Okada, T.; Hasegawa, A.

2007-01-01

We determine the source parameters of a M4.9 ?? 0.1 'characteristic earthquake' sequence and its accompanying microearthquakes at ???50 km depth on the subduction plate boundary offshore of Kamaishi, NE Japan. The microearthquakes tend to occur more frequently in the latter half of the recurrence intervals of the M4.9 ?? 0.1 events. Our results show that the microearthquakes are repeating events and they are located not only around but also within the slip area for the 2001 M4.8 event. From the hierarchical structure of slip areas and smaller stress drops for the microearthquakes compared to the M4.8 event, we infer the small repeating earthquakes rupture relatively weak patches in and around the slip area for the M4.8 event and their activity reflects a stress concentration process and/or change in frictional property (healing) at the area. We also infer the patches for the M4.9 ?? 0.1 and other repeating earthquakes undergo aseismic slip during their interseismic period. Copyright 2007 by the American Geophysical Union.

Role of zircon in tracing crustal growth and recycling

NASA Technical Reports Server (NTRS)

Compston, W.; Williams, I. S.; Armstrong, R. A.; Claoue-Long, J. C.; Kinny, P. D.; Foster, J. J.; Kroener, A.; Pidgeon, R. T.; Myers, J. S.

1988-01-01

Single crystal ion probe ages of zircons is discussed, which allow much better time resolution compared to other geochronological methods, although the technique is not without problems. Rocks from two areas that contain composite zircon populations, including true magmatic zircons as well as a variety of xenocrystic types are described. It is often difficult to distinguish these; xenocrystic zircons, for example, cannot always be identified on the basis of morphology alone. Additional evidence is needed before making age interpretations. Evidence is also presented of zircon growth long after the original time of crystallization, in some cases apparently at temperatures less than 300 C. The spectacular discovery of 4.1 to 4.2 Ga detrital zircons in metaquartzites from the Mount Narryer area of Western Australia is described. Similar zircons with ages as old as 4276 Ma have been found in the nearby Jack Hills area. The source areas or parent lithologies of these zircons have not yet been determined, but the author expects that they may be unrecognized or buried antecedents of the K rich Narryer gneisses. U or Th concentrations of zircon cannot be used to discriminate between felsic and mafic source rocks.

An analysis of urban thermal characteristics and associated land cover in Tampa Bay and Las Vegas using Landsat satellite data

USGS Publications Warehouse

Xian, George; Crane, Mike

2006-01-01

Remote sensing data from both Landsat 5 and Landsat 7 systems were utilized to assess urban area thermal characteristics in Tampa Bay watershed of west-central Florida, and the Las Vegas valley of southern Nevada. To quantitatively determine urban land use extents and development densities, sub-pixel impervious surface areas were mapped for both areas. The urban–rural boundaries and urban development densities were defined by selecting certain imperviousness threshold values and Landsat thermal bands were used to investigate urban surface thermal patterns. Analysis results suggest that urban surface thermal characteristics and patterns can be identified through qualitatively based urban land use and development density data. Results show the urban area of the Tampa Bay watershed has a daytime heating effect (heat-source), whereas the urban surface in Las Vegas has a daytime cooling effect (heat-sink). These thermal effects strongly correlated with urban development densities where higher percent imperviousness is usually associated with higher surface temperature. Using vegetation canopy coverage information, the spatial and temporal distributions of urban impervious surface and associated thermal characteristics are demonstrated to be very useful sources in quantifying urban land use, development intensity, and urban thermal patterns.

Irrigated Acreage Within the Basin and Range Carbonate-Rock Aquifer System, White Pine County, Nevada, and Adjacent Areas in Nevada and Utah

USGS Publications Warehouse

Welborn, Toby L.; Moreo, Michael T.

2007-01-01

Accurate delineations of irrigated acreage are needed for the development of water-use estimates and in determining water-budget calculations for the Basin and Range carbonate-rock aquifer system (BARCAS) study. Irrigated acreage is estimated routinely for only a few basins in the study area. Satellite imagery from the Landsat Thematic Mapper and Enhanced Thematic Mapper platforms were used to delineate irrigated acreage on a field-by-field basis for the entire study area. Six hundred and forty-three fields were delineated. The water source, irrigation system, crop type, and field activity for 2005 were identified and verified through field reconnaissance. These data were integrated in a geodatabase and analyzed to develop estimates of irrigated acreage for the 2000, 2002, and 2005 growing seasons by hydrographic area and subbasin. Estimated average annual potential evapotranspiration and average annual precipitation also were estimated for each field.The geodatabase was analyzed to determine the spatial distribution of field locations, the total amount of irrigated acreage by potential irrigation water source, by irrigation system, and by crop type. Irrigated acreage in 2005 totaled nearly 32,000 acres ranging from less than 200 acres in Butte, Cave, Jakes, Long, and Tippett Valleys to 9,300 acres in Snake Valley. Irrigated acreage increased about 20 percent between 2000 and 2005 and increased the most in Snake and White River Valleys. Ground-water supplies as much as 80 percent of irrigation water during dry years. Almost 90 percent of the irrigated acreage was planted with alfalfa.

Monitoring of nitrates in drinking water from agricultural and residential areas of Podravina and Prigorje (Croatia).

PubMed

Nemčić-Jurec, Jasna; Konjačić, Miljenko; Jazbec, Anamarija

2013-11-01

Nitrates are the most common chemical pollutant of groundwater in agricultural and suburban areas. Croatia must comply with the Nitrate Directive (91/676/EEC) whose aim is to reduce water pollution by nitrates originating from agriculture and to prevent further pollution. Podravina and Prigorje are the areas with a relatively high degree of agricultural activity. Therefore, the aim of this study was, by monitoring nitrates, to determine the distribution of nitrates in two different areas, Podravina and Prigorje (Croatia), to determine sources of contamination as well as annual and seasonal trends. The nitrate concentrations were measured in 30 wells (N = 382 samples) in Prigorje and in 19 wells (N = 174 samples) in Podravina from 2002 to 2007. In Podravina, the nitrate content was 24.9 mg/l and 6% of the samples were above the maximum available value (MAV), and in Prigorje the content was 53.9 mg/l and 38% of the samples above MAV. The wells were classified as correct, occasionally incorrect and incorrect. In the group of occasionally incorrect and incorrect wells, the point sources were within 10 m of the well. There is no statistically significant difference over the years or seasons within the year, but the interaction between locations and years was significant. Nitrate concentrations' trend was not significant during the monitoring. These results are a prerequisite for the adjustment of Croatian standards to those of the EU and will contribute to the implementation of the Nitrate Directive and the Directives on Environmental Protection in Croatia and the EU.

Toronto area ozone: Long-term measurements and modeled sources of poor air quality events

NASA Astrophysics Data System (ADS)

Whaley, C. H.; Strong, K.; Jones, D. B. A.; Walker, T. W.; Jiang, Z.; Henze, D. K.; Cooke, M. A.; McLinden, C. A.; Mittermeier, R. L.; Pommier, M.; Fogal, P. F.

2015-11-01

The University of Toronto Atmospheric Observatory and Environment Canada's Centre for Atmospheric Research Experiments each has over a decade of ground-based Fourier transform infrared (FTIR) spectroscopy measurements in southern Ontario. We present the Toronto area FTIR time series from 2002 to 2013 of two tropospheric trace gases—ozone and carbon monoxide—along with surface in situ measurements taken by government monitoring programs. We interpret their variability with the GEOS-Chem chemical transport model and determine the atmospheric conditions that cause pollution events in the time series. Our analysis includes a regionally tagged O3 model of the 2004-2007 time period, which quantifies the geographical contributions to Toronto area O3. The important emission types for 15 pollution events are then determined with a high-resolution adjoint model. Toronto O3, during pollution events, is most sensitive to southern Ontario and U.S. fossil fuel NOx emissions and natural isoprene emissions. The sources of Toronto pollution events are found to be highly variable, and this is demonstrated in four case studies representing local, short-, middle-, and long-range transport scenarios. This suggests that continental-scale emission reductions could improve air quality in the Toronto region. We also find that abnormally high temperatures and high-pressure systems are common to all pollution events studied, suggesting that climate change may impact Toronto O3. Finally, we quantitatively compare the sensitivity of the surface and column measurements to anthropogenic NOx emissions and show that they are remarkably similar. This work thus demonstrates the usefulness of FTIR measurements in an urban area to assess air quality.

Analysis of hydrogeochemical facies in groundwater of upper part of Cross River Basin, southeastern Nigeria

NASA Astrophysics Data System (ADS)

Stephen, Ukpai N.; Celestine, Okogbue O.; Solomon, Onwuka O.

2017-07-01

Upper Cross River Hydrogeological Basin lies within latitudes 60 021N to 60 241N and longitudes 80 001E to 80 161E, and is generally underlain by shales of Asu River group of Albian age. The area has Histories of intensive mineralization which influenced groundwater system, resulting to occurrence of different water types. This study determines the various water types via evaluation of major ion concentration from representative water samples collected across the area. Twenty (20) water samples were analyzed using Spectrophotometer of HACH DR/2010 series, and results showed that groundwater in the area is generally hard and polluted with TDS in some places. Statistical inspection was performed on the results using aqua-chem, and it delineated five hydro-chemical facies, namely: Ca-Mg-Cl-S04, Ca-Mg-HCO3-Cl-SO4, Ca-Mg-HCO3, Na-K-HCO3 and Na-K-Cl-SO4; all lie between slight acidic and weak alkaline water. These chemical facies (water types) diffused from non-point sources in urban area and point source from south of Abakaliki town. The dispersion of the facies plumes is possibly controlled by advection process through structural weak zones such as fractures. Hydraulic heads determined from hand-dug wells indicate local potentiometric surfaces, hence, showed local groundwater flow system which is possibly controlled by the underlying low permeable aquicludes formed by shales. The protective capacity of the aquitards was somewhat reduced by the permeating fractures which exposed the aquifers to polluting effects of mineralized water-types.

Occurrence and availability of ground water in the Athens region, northeastern Georgia

USGS Publications Warehouse

Radtke, D.B.; Cressler, C.W.; Perlman, H.A.; Blanchard, H.E.; McFadden, K.W.; Brooks, Rebekah

1986-01-01

A study was conducted to assess the occurrence and availability of groundwater in the crystalline rocks of the Piedmont area in northeastern Georgia and to determine whether groundwater is a viable alternative or supplemental source for industrial, public and private supplies. The area is underlain by a variety of metamorphic and igneous rocks. The quantity of water that a rock unit can supply to wells is determined by the number, capacity, and interconnection of the secondary openings. Of an estimated 10,000 successful wells drilled in the Athens Region, 972 wells are reported by drilling contractors to supply from 20 to 300 gal/min. Studies of well sites revealed that high yielding wells can be developed only where the water bearing units have undergone significant increases in secondary permeability. This occurs mainly in association with (1) contact zones between rock units of contrasting character, (2) contact zones within multilayered rock units, (3) fault zones, (4) stress-relief fractures, and (5) shear zones. Groundwater may be a viable alternative or supplemental source for industrial, public, and private supplies in much of the Athens Region. In 1980, groundwater made up 38% (18 million gal/day) of the total water used in the area. Yields of 20 to more than 200 gal/min are obtained from wells throughout most of the region, and the water is generally of good chemical quality and is suitable for drinking and many other uses. Concentrations of dissolved constituents are fairly consistent throughout the area. Except for iron, manganese, and fluoride, dissolved constituents rarely exceed drinking water standards. (Lantz-PTT)

Local ventilation solution for large, warm emission sources.

PubMed

Kulmala, Ilpo; Hynynen, Pasi; Welling, Irma; Säämänen, Arto

2007-01-01

In a foundry casting line, contaminants are released from a large area. Casting fumes include both volatile and particulate compounds. The volatile fraction contains hydrocarbons, whereas the particulate fraction mostly comprises a mixture of vaporized metal fumes. Casting fumes lower the air quality in foundries. The design of local ventilation for the casting area is a challenging task, because of the large casting area and convection plumes from warm moulds. A local ventilation solution for the mould casting area was designed and dimensioned with the aid of computational fluid dynamic (CFD) calculations. According to the calculations, the most efficient solution was a push-pull ventilation system. The prototype of the push-pull system was built and tested in actual operation at the foundry. The push flow was generated by a free plane jet that blew across the 10 m wide casting area towards an exhaust hood on the opposite side of the casting lines. The capture efficiency of the prototype was determined by the tracer gas method. The measured capture efficiencies with push jet varied between 40 and 80%, depending on the distance between the source and the exhaust. With the aid of the push flow, the average capture efficiency was increased from 40 (without jet) to 60%.