Simple and versatile long range swept source for optical coherence tomography applications

NASA Astrophysics Data System (ADS)

Bräuer, Bastian; Lippok, Norman; Murdoch, Stuart G.; Vanholsbeeck, Frédérique

2015-12-01

We present a versatile long coherence length swept-source laser design for optical coherence tomography applications. This design consists of a polygonal spinning mirror and an optical gain chip in a modified Littman-Metcalf cavity. A narrowband intra-cavity filter is implemented through multiple passes off a diffraction grating set at grazing incidence. The key advantage of this design is that it can be readily adapted to any wavelength regions for which broadband gain chips are available. We demonstrate this by implementing sources at 1650 nm, 1550 nm, 1310 nm and 1050 nm. In particular, we present a 1310 nm swept source laser with 24 mm coherence length, 95 nm optical bandwidth, 2 kHz maximum sweep frequency and 7.5 mW average output power. These parameters make it a suitable source for the imaging of biological samples.

Research on starlight hardware-in-the-loop simulator

NASA Astrophysics Data System (ADS)

Zhang, Ying; Gao, Yang; Qu, Huiyang; Liu, Dongfang; Du, Huijie; Lei, Jie

2016-10-01

The starlight navigation is considered to be one of the most important methods for spacecraft navigation. Starlight simulation system is a high-precision system with large fields of view, designed to test the starlight navigation sensor performance on the ground. A complete hardware-in-the-loop simulation of the system has been built. The starlight simulator is made up of light source, light source controller, light filter, LCD, collimator and control computer. LCD is the key display component of the system, and is installed at the focal point of the collimator. For the LCD cannot emit light itself, so light source and light source power controller is specially designed for the brightness demanded by the LCD. Light filter is designed for the dark background which is also needed in the simulation.

Structure-borne noise at hotels

NASA Astrophysics Data System (ADS)

Wilson, George Paul; Jue, Deborah A.

2002-11-01

Hotels present a challenging environment for building designers to provide suitable noise and vibration isolation between very incompatible uses. While many are familiar with ways to reduce traditional sources of airborne noise and vibration, structure-borne noise and vibration are often overlooked, often with costly repercussions. Structure-borne noise can be very difficult to pinpoint, and troubleshooting the sources of the vibration can be a tedious process. Therefore, the best approach is to avoid the problem altogether during design, with attention to the building construction, potential vibration sources, building uses and equipment locations. In this paper, the relationship between structure-borne vibration and noise are reviewed, typical vibration sources discussed (e.g., aerobic rooms, laundry rooms, mechanical equipment/building services, and subway rail transit), and key details and design guidance to minimize structure-borne noise provided.

Toward Wireless Health Monitoring via an Analog Signal Compression-Based Biosensing Platform.

PubMed

Zhao, Xueyuan; Sadhu, Vidyasagar; Le, Tuan; Pompili, Dario; Javanmard, Mehdi

2018-06-01

Wireless all-analog biosensor design for the concurrent microfluidic and physiological signal monitoring is presented in this paper. The key component is an all-analog circuit capable of compressing two analog sources into one analog signal by the analog joint source-channel coding (AJSCC). Two circuit designs are discussed, including the stacked-voltage-controlled voltage source (VCVS) design with the fixed number of levels, and an improved design, which supports a flexible number of AJSCC levels. Experimental results are presented on the wireless biosensor prototype, composed of printed circuit board realizations of the stacked-VCVS design. Furthermore, circuit simulation and wireless link simulation results are presented on the improved design. Results indicate that the proposed wireless biosensor is well suited for sensing two biological signals simultaneously with high accuracy, and can be applied to a wide variety of low-power and low-cost wireless continuous health monitoring applications.

Direct design of aspherical lenses for extended non-Lambertian sources in three-dimensional rotational geometry

PubMed Central

Wu, Rengmao; Hua, Hong

2016-01-01

Illumination design used to redistribute the spatial energy distribution of light source is a key technique in lighting applications. However, there is still no effective illumination design method for extended sources, especially for extended non-Lambertian sources. What we present here is to our knowledge the first direct method for extended non-Lambertian sources in three-dimensional (3D) rotational geometry. In this method, both meridional rays and skew rays of the extended source are taken into account to tailor the lens profile in the meridional plane. A set of edge rays and interior rays emitted from the extended source which will take a given direction after the refraction of the aspherical lens are found by the Snell’s law, and the output intensity at this direction is then calculated to be the integral of the luminance function of the outgoing rays at this direction. This direct method is effective for both extended non-Lambertian sources and extended Lambertian sources in 3D rotational symmetry, and can directly find a solution to the prescribed design problem without cumbersome iterative illuminance compensation. Two examples are presented to demonstrate the effectiveness of the proposed method in terms of performance and capacity for tackling complex designs. PMID:26832484

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Na; Wu, Yu-Ping; Min, Hao

A radio-frequency (RF) source designed for cold atom experiments is presented. The source uses AD9858, a direct digital synthesizer, to generate the sine wave directly, up to 400 MHz, with sub-Hz resolution. An amplitude control circuit consisting of wideband variable gain amplifier and high speed digital to analog converter is integrated into the source, capable of 70 dB off isolation and 4 ns on-off keying. A field programmable gate array is used to implement a versatile frequency and amplitude co-sweep logic. Owing to modular design, the RF sources have been used on many cold atom experiments to generate various complicatedmore » RF sequences, enriching the operation schemes of cold atoms, which cannot be done by standard RF source instruments.« less

ClinicalKey 2.0: Upgrades in a Point-of-Care Search Engine.

PubMed

Huslig, Mary Ann; Vardell, Emily

2015-01-01

ClinicalKey 2.0, launched September 23, 2014, offers a mobile-friendly design with a search history feature for targeting point-of-care resources for health care professionals. Browsing is improved with searchable, filterable listings of sources highlighting new resources. ClinicalKey 2.0 improvements include more than 1,400 new Topic Pages for quick access to point-of-care content. A sample search details some of the upgrades and content options.

RRM3 Fluid Management Device

NASA Technical Reports Server (NTRS)

Barfknecht, P.; Benson, D.; Boyle, R.; DeLee, C.; DiPirro, M.; Francis, J.; Li, X.; McGuire, J.; Mustafi, S.; Tuttle, J.;

The development of data acquisition and processing application system for RF ion source

NASA Astrophysics Data System (ADS)

Zhang, Xiaodan; Wang, Xiaoying; Hu, Chundong; Jiang, Caichao; Xie, Yahong; Zhao, Yuanzhe

2017-07-01

As the key ion source component of nuclear fusion auxiliary heating devices, the radio frequency (RF) ion source is developed and applied gradually to offer a source plasma with the advantages of ease of control and high reliability. In addition, it easily achieves long-pulse steady-state operation. During the process of the development and testing of the RF ion source, a lot of original experimental data will be generated. Therefore, it is necessary to develop a stable and reliable computer data acquisition and processing application system for realizing the functions of data acquisition, storage, access, and real-time monitoring. In this paper, the development of a data acquisition and processing application system for the RF ion source is presented. The hardware platform is based on the PXI system and the software is programmed on the LabVIEW development environment. The key technologies that are used for the implementation of this software programming mainly include the long-pulse data acquisition technology, multi-threading processing technology, transmission control communication protocol, and the Lempel-Ziv-Oberhumer data compression algorithm. Now, this design has been tested and applied on the RF ion source. The test results show that it can work reliably and steadily. With the help of this design, the stable plasma discharge data of the RF ion source are collected, stored, accessed, and monitored in real-time. It is shown that it has a very practical application significance for the RF experiments.

Key metrics for HFIR HEU and LEU models

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ilas, Germina; Betzler, Benjamin R.; Chandler, David

This report compares key metrics for two fuel design models of the High Flux Isotope Reactor (HFIR). The first model represents the highly enriched uranium (HEU) fuel currently in use at HFIR, and the second model considers a low-enriched uranium (LEU) interim design fuel. Except for the fuel region, the two models are consistent, and both include an experiment loading that is representative of HFIR's current operation. The considered key metrics are the neutron flux at the cold source moderator vessel, the mass of 252Cf produced in the flux trap target region as function of cycle time, the fast neutronmore » flux at locations of interest for material irradiation experiments, and the reactor cycle length. These key metrics are a small subset of the overall HFIR performance and safety metrics. They were defined as a means of capturing data essential for HFIR's primary missions, for use in optimization studies assessing the impact of HFIR's conversion from HEU fuel to different types of LEU fuel designs.« less

Analytical methods development for supramolecular design in solar hydrogen production

NASA Astrophysics Data System (ADS)

Brown, J. R.; Elvington, M.; Mongelli, M. T.; Zigler, D. F.; Brewer, K. J.

2006-08-01

In the investigation of alternative energy sources, specifically, solar hydrogen production from water, the ability to perform experiments with a consistent and reproducible light source is key to meaningful photochemistry. The design, construction, and evaluation of a series of LED array photolysis systems for high throughput photochemistry have been performed. Three array systems of increasing sophistication are evaluated using calorimetric measurements and potassium tris(oxalato)ferrate(II) chemical actinometry and compared with a traditional 1000 W Xe arc lamp source. The results are analyzed using descriptive statistics and analysis of variance (ANOVA). The third generation array is modular, and controllable in design. Furthermore, the third generation array system is shown to be comparable in both precision and photonic output to a 1000 W Xe arc lamp.

Mid-infrared Shack-Hartmann wavefront sensor fully cryogenic using extended source for endoatmospheric applications.

PubMed

Robert, Clélia; Michau, Vincent; Fleury, Bruno; Magli, Serge; Vial, Laurent

2012-07-02

Adaptive optics provide real-time compensation for atmospheric turbulence. The correction quality relies on a key element: the wavefront sensor. We have designed an adaptive optics system in the mid-infrared range providing high spatial resolution for ground-to-air applications, integrating a Shack-Hartmann infrared wavefront sensor operating on an extended source. This paper describes and justifies the design of the infrared wavefront sensor, while defining and characterizing the Shack-Hartmann wavefront sensor camera. Performance and illustration of field tests are also reported.

ProFound: Source Extraction and Application to Modern Survey Data

NASA Astrophysics Data System (ADS)

Robotham, A. S. G.; Davies, L. J. M.; Driver, S. P.; Koushan, S.; Taranu, D. S.; Casura, S.; Liske, J.

2018-05-01

We introduce PROFOUND, a source finding and image analysis package. PROFOUND provides methods to detect sources in noisy images, generate segmentation maps identifying the pixels belonging to each source, and measure statistics like flux, size, and ellipticity. These inputs are key requirements of PROFIT, our recently released galaxy profiling package, where the design aim is that these two software packages will be used in unison to semi-automatically profile large samples of galaxies. The key novel feature introduced in PROFOUND is that all photometry is executed on dilated segmentation maps that fully contain the identifiable flux, rather than using more traditional circular or ellipse-based photometry. Also, to be less sensitive to pathological segmentation issues, the de-blending is made across saddle points in flux. We apply PROFOUND in a number of simulated and real-world cases, and demonstrate that it behaves reasonably given its stated design goals. In particular, it offers good initial parameter estimation for PROFIT, and also segmentation maps that follow the sometimes complex geometry of resolved sources, whilst capturing nearly all of the flux. A number of bulge-disc decomposition projects are already making use of the PROFOUND and PROFIT pipeline, and adoption is being encouraged by publicly releasing the software for the open source R data analysis platform under an LGPL-3 license on GitHub (github.com/asgr/ProFound).

The New Youth Entrepreneur: Getting Ready for Entrepreneurship. Opportunities-They Are All Around You. Module 2.

ERIC Educational Resources Information Center

Kourilsky, Marilyn; And Others

The New Youth Entrepreneur curriculum is a series of 12 youth-oriented educational modules containing instructional materials, learning activities, and checkup exercises designed to teach students key elements of entrepreneurship. This document is the second module, designed to help students define the notion of opportunity, determine sources of…

Active control on high-order coherence and statistic characterization on random phase fluctuation of two classical point sources.

PubMed

Hong, Peilong; Li, Liming; Liu, Jianji; Zhang, Guoquan

2016-03-29

Young's double-slit or two-beam interference is of fundamental importance to understand various interference effects, in which the stationary phase difference between two beams plays the key role in the first-order coherence. Different from the case of first-order coherence, in the high-order optical coherence the statistic behavior of the optical phase will play the key role. In this article, by employing a fundamental interfering configuration with two classical point sources, we showed that the high- order optical coherence between two classical point sources can be actively designed by controlling the statistic behavior of the relative phase difference between two point sources. Synchronous position Nth-order subwavelength interference with an effective wavelength of λ/M was demonstrated, in which λ is the wavelength of point sources and M is an integer not larger than N. Interestingly, we found that the synchronous position Nth-order interference fringe fingerprints the statistic trace of random phase fluctuation of two classical point sources, therefore, it provides an effective way to characterize the statistic properties of phase fluctuation for incoherent light sources.

Compliance Groundwater Monitoring of Nonpoint Sources - Emerging Approaches

NASA Astrophysics Data System (ADS)

Harter, T.

2008-12-01

Groundwater monitoring networks are typically designed for regulatory compliance of discharges from industrial sites. There, the quality of first encountered (shallow-most) groundwater is of key importance. Network design criteria have been developed for purposes of determining whether an actual or potential, permitted or incidental waste discharge has had or will have a degrading effect on groundwater quality. The fundamental underlying paradigm is that such discharge (if it occurs) will form a distinct contamination plume. Networks that guide (post-contamination) mitigation efforts are designed to capture the shape and dynamics of existing, finite-scale plumes. In general, these networks extend over areas less than one to ten hectare. In recent years, regulatory programs such as the EU Nitrate Directive and the U.S. Clean Water Act have forced regulatory agencies to also control groundwater contamination from non-incidental, recharging, non-point sources, particularly agricultural sources (fertilizer, pesticides, animal waste application, biosolids application). Sources and contamination from these sources can stretch over several tens, hundreds, or even thousands of square kilometers with no distinct plumes. A key question in implementing monitoring programs at the local, regional, and national level is, whether groundwater monitoring can be effectively used as a landowner compliance tool, as is currently done at point-source sites. We compare the efficiency of such traditional site-specific compliance networks in nonpoint source regulation with various designs of regional nonpoint source monitoring networks that could be used for compliance monitoring. We discuss advantages and disadvantages of the site vs. regional monitoring approaches with respect to effectively protecting groundwater resources impacted by nonpoint sources: Site-networks provide a tool to enforce compliance by an individual landowner. But the nonpoint source character of the contamination and its typically large spatial extend requires extensive networks at an individual site to accurately and fairly monitor individual compliance. In contrast, regional networks seemingly fail to hold individual landowners accountable. But regional networks can effectively monitor large-scale impacts and water quality trends; and thus inform regulatory programs that enforce management practices tied to nonpoint source pollution. Regional monitoring networks for compliance purposes can face significant challenges in the implementation due to a regulatory and legal landscape that is exclusively structured to address point sources and individual liability, and due to the non-intensive nature of a regional monitoring program (lack of control of hot spots; lack of accountability of individual landowners).

Design and Construction of an Entity Resolution System that Supports Entity Identity Information Management and Asserted Resolution

ERIC Educational Resources Information Center

Nelson, Eric Derrand

2011-01-01

This work describes the design and construction of an open source, entity resolution system that enables users to assign and maintain persistent identifiers for master data items. Two key features of this system that are not available in current ER systems and that make persistent identification possible are (1) The capture and management of…

A Design Basis for Spacecraft Cabin Trace Contaminant Control

NASA Technical Reports Server (NTRS)

Perry, Jay L.

2009-01-01

Successful trace chemical contamination control is one of the components necessary for achieving good cabin atmospheric quality. While employing seemingly simple process technologies, sizing the active contamination control equipment must employ a reliable design basis for the trace chemical load in the cabin atmosphere. A simplified design basis that draws on experience gained from the International Space Station program is presented. The trace chemical contamination control design load refines generation source magnitudes and includes key chemical functional groups representing both engineering and toxicology challenges.

Economic evaluation in chronic pain: a systematic review and de novo flexible economic model.

PubMed

Sullivan, W; Hirst, M; Beard, S; Gladwell, D; Fagnani, F; López Bastida, J; Phillips, C; Dunlop, W C N

2016-07-01

There is unmet need in patients suffering from chronic pain, yet innovation may be impeded by the difficulty of justifying economic value in a field beset by data limitations and methodological variability. A systematic review was conducted to identify and summarise the key areas of variability and limitations in modelling approaches in the economic evaluation of treatments for chronic pain. The results of the literature review were then used to support the development of a fully flexible open-source economic model structure, designed to test structural and data assumptions and act as a reference for future modelling practice. The key model design themes identified from the systematic review included: time horizon; titration and stabilisation; number of treatment lines; choice/ordering of treatment; and the impact of parameter uncertainty (given reliance on expert opinion). Exploratory analyses using the model to compare a hypothetical novel therapy versus morphine as first-line treatments showed cost-effectiveness results to be sensitive to structural and data assumptions. Assumptions about the treatment pathway and choice of time horizon were key model drivers. Our results suggest structural model design and data assumptions may have driven previous cost-effectiveness results and ultimately decisions based on economic value. We therefore conclude that it is vital that future economic models in chronic pain are designed to be fully transparent and hope our open-source code is useful in order to aspire to a common approach to modelling pain that includes robust sensitivity analyses to test structural and parameter uncertainty.

Transport outlook 2008 : focusing on CO2 emissions from road vehicles

DOT National Transportation Integrated Search

2008-05-01

This short outlook is designed to test the potential for key policy instruments for mitigating emissions from road transport, and particularly from light duty vehicles, the largest source of CO2 emissions from transport. It also examines uncertaintie...

International Space Station Major Constituent Analyzer On-Orbit Performance

NASA Technical Reports Server (NTRS)

Gardner, Ben D.; Erwin, Phillip M.; Thoresen, Souzan; Wiedemann, Rachel; Matty, Chris

2015-01-01

The Major Constituent Analyzer is a mass spectrometer based system that measures the major atmospheric constituents on the International Space Station. A number of limited-life components require periodic change-out, including the ORU 02 analyzer and the ORU 08 Verification Gas Assembly. Improvements to ion pump operation and ion source tuning have improved lifetime performance of the current ORU 02 design. The most recent ORU 02 analyzer assemblies, as well as ORU 08, have operated nominally. For ORU 02, the ion source filaments and ion pump lifetime continue to be key determinants of MCA performance and logistical support. Monitoring several key parameters provides the capacity to monitor ORU health and properly anticipate end of life.

Space Ultrareliable Modular Computer (SUMC) instruction simulator

NASA Technical Reports Server (NTRS)

Curran, R. T.

1972-01-01

The design principles, description, functional operation, and recommended expansion and enhancements are presented for the Space Ultrareliable Modular Computer interpretive simulator. Included as appendices are the user's manual, program module descriptions, target instruction descriptions, simulator source program listing, and a sample program printout. In discussing the design and operation of the simulator, the key problems involving host computer independence and target computer architectural scope are brought into focus.

Mechanical design and fabrication of the VHF-gun, the Berkeley normal-conducting continuous-wave high-brightness electron source

NASA Astrophysics Data System (ADS)

Wells, R. P.; Ghiorso, W.; Staples, J.; Huang, T. M.; Sannibale, F.; Kramasz, T. D.

2016-02-01

A high repetition rate, MHz-class, high-brightness electron source is a key element in future high-repetition-rate x-ray free electron laser-based light sources. The VHF-gun, a novel low frequency radio-frequency gun, is the Lawrence Berkeley National Laboratory (LBNL) response to that need. The gun design is based on a normal conducting, single cell cavity resonating at 186 MHz in the VHF band and capable of continuous wave operation while still delivering the high accelerating fields at the cathode required for the high brightness performance. The VHF-gun was fabricated and successfully commissioned in the framework of the Advanced Photo-injector EXperiment, an injector built at LBNL to demonstrate the capability of the gun to deliver the required beam quality. The basis for the selection of the VHF-gun technology, novel design features, and fabrication techniques are described.

Mechanical design and fabrication of the VHF-gun, the Berkeley normal-conducting continuous-wave high-brightness electron source.

PubMed

Wells, R P; Ghiorso, W; Staples, J; Huang, T M; Sannibale, F; Kramasz, T D

2016-02-01

A high repetition rate, MHz-class, high-brightness electron source is a key element in future high-repetition-rate x-ray free electron laser-based light sources. The VHF-gun, a novel low frequency radio-frequency gun, is the Lawrence Berkeley National Laboratory (LBNL) response to that need. The gun design is based on a normal conducting, single cell cavity resonating at 186 MHz in the VHF band and capable of continuous wave operation while still delivering the high accelerating fields at the cathode required for the high brightness performance. The VHF-gun was fabricated and successfully commissioned in the framework of the Advanced Photo-injector EXperiment, an injector built at LBNL to demonstrate the capability of the gun to deliver the required beam quality. The basis for the selection of the VHF-gun technology, novel design features, and fabrication techniques are described.

Investigation of the adhesive bonding technology for the insulator structure of EAST neutral beam injector

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wei, Jiang-Long, E-mail: jlwei@ipp.ac.cn; Li, Jun; Hu, Chun-Dong

A key issue on the development of EAST ion source was the junction design of insulator structure, which consists of three insulators and four supporting flanges of electrode grid. Because the ion source is installed on the vertical plane, the insulator structure has to withstand large bending and shear stress due to the gravity of whole ion source. Through a mechanical analysis, it was calculated that the maximum bending normal stress was 0.34 MPa and shear stress was 0.23 MPa on the insulator structure. Due to the advantages of simplicity and high strength, the adhesive bonding technology was applied tomore » the junction of insulator structure. A tensile testing campaign of different junction designs between insulator and supporting flange was performed, and a junction design of stainless steel and fiber enhanced epoxy resin with epoxy adhesive was determined. The insulator structure based on the determined design can satisfy both the requirements of high-voltage holding and mechanical strength.« less

The WEAVE-LOFAR Survey

NASA Astrophysics Data System (ADS)

Smith, D. J. B.; Best, P. N.; Duncan, K. J.; Hatch, N. A.; Jarvis, M. J.; Röttgering, H. J. A.; Simpson, C. J.; Stott, J. P.; Cochrane, R. K.; Coppin, K. E.; Dannerbauer, H.; Davis, T. A.; Geach, J. E.; Hale, C. L.; Hardcastle, M. J.; Hatfield, P. W.; Houghton, R. C. W.; Maddox, N.; McGee, S. L.; Morabito, L.; Nisbet, D.; Pandey-Pommier, M.; Prandoni, I.; Saxena, A.; Shimwell, T. W.; Tarr, M.; van Bemmel, I.; Verma, A.; White, G. J.; Williams, W. L.

2016-12-01

In these proceedings we highlight the primary scientific goals and design of the WEAVE-LOFAR survey, which will use the new WEAVE spectrograph on the 4.2m William Herschel Telescope to provide the primary source of spectroscopic information for the LOFAR Surveys Key Science Project. Beginning in 2018, WEAVE-LOFAR will generate more than 10^6 R=5000 365-960nm spectra of low-frequency selected radio sources, across three tiers designed to efficiently sample the redshift-luminosity plane, and produce a data set of enormous legacy value. The radio frequency selection, combined with the high multiplex and throughput of the WEAVE spectrograph, make obtaining redshifts in this way very efficient, and we expect that the redshift success rate will approach 100 per cent at z < 1. This unprecedented spectroscopic sample - which will be complemented by an integral field component - will be transformational in key areas, including studying the star formation history of the Universe, the role of accretion and AGN-driven feedback, properties of the epoch of reionisation, cosmology, cluster haloes and relics, as well as the nature of radio galaxies and protoclusters. Each topic will be addressed in unprecedented detail, and with the most reliable source classifications and redshift information in existence.

Computational wave dynamics for innovative design of coastal structures

PubMed Central

GOTOH, Hitoshi; OKAYASU, Akio

2017-01-01

For innovative designs of coastal structures, Numerical Wave Flumes (NWFs), which are solvers of Navier-Stokes equation for free-surface flows, are key tools. In this article, various methods and techniques for NWFs are overviewed. In the former half, key techniques of NWFs, namely the interface capturing (MAC, VOF, C-CUP) and significance of NWFs in comparison with the conventional wave models are described. In the latter part of this article, recent improvements of the particle method are shown as one of cores of NWFs. Methods for attenuating unphysical pressure fluctuation and improving accuracy, such as CMPS method for momentum conservation, Higher-order Source of Poisson Pressure Equation (PPE), Higher-order Laplacian, Error-Compensating Source in PPE, and Gradient Correction for ensuring Taylor-series consistency, are reviewed briefly. Finally, the latest new frontier of the accurate particle method, including Dynamic Stabilization for providing minimum-required artificial repulsive force to improve stability of computation, and Space Potential Particle for describing the exact free-surface boundary condition, is described. PMID:29021506

Exoskeleton for Soldier Enhancement Systems Feasibility Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jansen, J.F.

2000-09-28

The development of a successful exoskeleton for human performance augmentation (EHPA) will require a multi-disciplinary systems approach based upon sound biomechanics, power generation and actuation systems, controls technology, and operator interfaces. The ability to integrate key components into a system that enhances performance without impeding operator mobility is essential. The purpose of this study and report are to address the issue of feasibility of building a fieldable EHPA. Previous efforts, while demonstrating progress and enhancing knowledge, have not approached the level required for a fully functional, fieldable system. It is doubtless that the technologies required for a successful exoskeleton havemore » advanced, and some of them significantly. The question to be addressed in this report is have they advanced to the point of making a system feasible in the next three to five years? In this study, the key technologies required to successfully build an exoskeleton have been examined. The primary focus has been on the key technologies of power sources, actuators, and controls. Power sources, including internal combustion engines, fuel cells, batteries, super capacitors, and hybrid sources have been investigated and compared with respect to the exoskeleton application. Both conventional and non-conventional actuator technologies that could impact EHPA have been assessed. In addition to the current state of the art of actuators, the potential for near-term improvements using non-conventional actuators has also been addressed. Controls strategies, and their implication to the design approach, and the exoskeleton to soldier interface have also been investigated. In addition to these key subsystems and technologies, this report addresses technical concepts and issues relating to an integrated design. A recommended approach, based on the results of the study is also presented.« less

CAGE IIIA Distributed Simulation Design Methodology

DTIC Science & Technology

2014-05-01

2 VHF Very High Frequency VLC Video LAN Codec – an Open-source cross-platform multimedia player and framework VM Virtual Machine VOIP Voice Over...Implementing Defence Experimentation (GUIDEx). The key challenges for this methodology are with understanding how to: • design it o define the...operation and to be available in the other nation’s simulations. The challenge for the CAGE campaign of experiments is to continue to build upon this

Development of electron beam ion source for nanoprocess using highly charged ions

NASA Astrophysics Data System (ADS)

Sakurai, Makoto; Nakajima, Fumiharu; Fukumoto, Takunori; Nakamura, Nobuyuki; Ohtani, Shunsuke; Mashiko, Shinro; Sakaue, Hiroyuki

2005-07-01

Highly charged ion is useful to produce nanostructure on various materials, and is key tool to realize single ion implantation technique. On such demands for the application to nanotechnology, we have designed an electron bean ion source. The design stresses on the volume of drift tubes where highly charged ions are confined and the efficiency of ion extraction from the drift tube through collector electrode in order to obtain intense ion beam as much as possible. The ion source uses a discrete superconducting magnet cooled by a closed-cycle refrigerator in order to reduce the running costs and to simplify the operating procedures. The electrodes of electron gun, drift tubes, and collector are enclosed in ultrahigh vacuum tube that is inserted into the bore of the magnet system.

Fatigue impact on Mod-1 wind turbine design

NASA Technical Reports Server (NTRS)

Stahle, C. V., Jr.

1978-01-01

Fatigue is a key consideration in the design of a long-life Wind Turbine Generator (WTG) system. This paper discusses the fatigue aspects of the large Mod-1 horizontal-axis WTG design starting with the characterization of the environment and proceeding through the design. Major sources of fatigue loading are discussed and methods of limiting fatigue loading are described. NASTRAN finite element models are used to determine dynamic loading and internal cyclic stresses. Recent developments in determining the allowable fatigue stress consistent with present construction codes are discussed relative to their application to WTG structural design.

CANCELLED Microwave Ion Source and Beam Injection for anAccelerator-Driven Neut ron Source

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vainionpaa, J.H.; Gough, R.; Hoff, M.

2007-02-27

An over-dense microwave driven ion source capable of producing deuterium (or hydrogen) beams at 100-200 mA/cm{sup 2} and with atomic fraction > 90% was designed and tested with an electrostatic low energy beam transport section (LEBT). This ion source was incorporated into the design of an Accelerator Driven Neutron Source (ADNS). The other key components in the ADNS include a 6 MeV RFQ accelerator, a beam bending and scanning system, and a deuterium gas target. In this design a 40 mA D{sup +} beam is produced from a 6 mm diameter aperture using a 60 kV extraction voltage. The LEBTmore » section consists of 5 electrodes arranged to form 2 Einzel lenses that focus the beam into the RFQ entrance. To create the ECR condition, 2 induction coils are used to create {approx} 875 Gauss on axis inside the source chamber. To prevent HV breakdown in the LEBT a magnetic field clamp is necessary to minimize the field in this region. Matching of the microwave power from the waveguide to the plasma is done by an autotuner. They observed significant improvement of the beam quality after installing a boron nitride liner inside the ion source. The measured emittance data are compared with PBGUNS simulations.« less

An adaptable dual species effusive source and Zeeman slower design demonstrated with Rb and Li

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bowden, William, E-mail: william.bowden@physics.ox.ac.uk; Gunton, Will; Semczuk, Mariusz

2016-04-15

We present a dual-species effusive source and Zeeman slower designed to produce slow atomic beams of two elements with a large mass difference and with very different oven temperature requirements. We demonstrate this design for the case of {sup 6}Li and {sup 85}Rb and achieve magneto-optical trap (MOT) loading rates equivalent to that reported in prior work on dual species (Rb+Li) Zeeman slowers operating at the same oven temperatures. Key design choices, including thermally separating the effusive sources and using a segmented coil design to enable computer control of the magnetic field profile, ensure that the apparatus can be easilymore » modified to slow other atomic species. By performing the final slowing using the quadrupole magnetic field of the MOT, we are able to shorten our Zeeman slower length making for a more compact system without compromising performance. We outline the construction and analyze the emission properties of our effusive sources. We also verify the performance of the source and slower, and we observe sequential loading rates of 12 × 10{sup 8} atoms/s for a Rb oven temperature of 140 °C and 1.1 × 10{sup 8} atoms/s for a Li reservoir at 460 °C, corresponding to reservoir lifetimes for continuous operation of 10 and 4 years, respectively.« less

Thermodynamic Performance and Cost Optimization of a Novel Hybrid Thermal-Compressed Air Energy Storage System Design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Houssainy, Sammy; Janbozorgi, Mohammad; Kavehpour, Pirouz

Compressed Air Energy Storage (CAES) can potentially allow renewable energy sources to meet electricity demands as reliably as coal-fired power plants. However, conventional CAES systems rely on the combustion of natural gas, require large storage volumes, and operate at high pressures, which possess inherent problems such as high costs, strict geological locations, and the production of greenhouse gas emissions. A novel and patented hybrid thermal-compressed air energy storage (HT-CAES) design is presented which allows a portion of the available energy, from the grid or renewable sources, to operate a compressor and the remainder to be converted and stored in themore » form of heat, through joule heating in a sensible thermal storage medium. The HT-CAES design incudes a turbocharger unit that provides supplementary mass flow rate alongside the air storage. The hybrid design and the addition of a turbocharger have the beneficial effect of mitigating the shortcomings of conventional CAES systems and its derivatives by eliminating combustion emissions and reducing storage volumes, operating pressures, and costs. Storage efficiency and cost are the two key factors, which upon integration with renewable energies would allow the sources to operate as independent forms of sustainable energy. The potential of the HT-CAES design is illustrated through a thermodynamic optimization study, which outlines key variables that have a major impact on the performance and economics of the storage system. The optimization analysis quantifies the required distribution of energy between thermal and compressed air energy storage, for maximum efficiency, and for minimum cost. This study provides a roundtrip energy and exergy efficiency map of the storage system and illustrates a trade off that exists between its capital cost and performance.« less

Overview of Mono-Energetic Gamma-Ray Sources and Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hartemann, Fred; /LLNL, Livermore; Albert, Felicie

2012-06-25

Recent progress in accelerator physics and laser technology have enabled the development of a new class of tunable gamma-ray light sources based on Compton scattering between a high-brightness, relativistic electron beam and a high intensity laser pulse produced via chirped-pulse amplification (CPA). A precision, tunable Mono-Energetic Gamma-ray (MEGa-ray) source driven by a compact, high-gradient X-band linac is currently under development and construction at LLNL. High-brightness, relativistic electron bunches produced by an X-band linac designed in collaboration with SLAC NAL will interact with a Joule-class, 10 ps, diode-pumped CPA laser pulse to generate tunable {gamma}-rays in the 0.5-2.5 MeV photon energymore » range via Compton scattering. This MEGaray source will be used to excite nuclear resonance fluorescence in various isotopes. Applications include homeland security, stockpile science and surveillance, nuclear fuel assay, and waste imaging and assay. The source design, key parameters, and current status are presented, along with important applications, including nuclear resonance fluorescence.« less

Unsteady Flow Dynamics and Acoustics of Two-Outlet Centrifugal Fan Design

NASA Astrophysics Data System (ADS)

Wong, I. Y. W.; Leung, R. C. K.; Law, A. K. Y.

2011-09-01

In this study, a centrifugal fan design with two flow outlets is investigated. This design aims to provide high mass flow rate but low noise performance. Two dimensional unsteady flow simulation with CFD code (FLUENT 6.3) is carried out to analyze the fan flow dynamics and its acoustics. The calculations were done using the unsteady Reynolds averaged Navier Stokes (URANS) approach in which effects of turbulence were accounted for using κ-ɛ model. This work aims to provide an insight how the dominant noise source mechanisms vary with a key fan geometrical paramters, namely, the ratio between cutoff distance and the radius of curvature of the fan housing. Four new fan designs were calculated. Simulation results show that the unsteady flow-induced forces on the fan blades are found to be the main noise sources. The blade force coefficients are then used to build the dipole source terms in Ffowcs Williams and Hawkings (FW-H) Equation for estimating their noise effects. It is found that one design is able to deliver a mass flow 34% more, but with sound pressure level (SPL) 10 dB lower, than the existing design .

Child Maltreatment Risk Assessments: An Evaluation Guide.

ERIC Educational Resources Information Center

Righthand, Sue; Kerr, Bruce; Drach, Kerry

This book is a professional practice manual designed to assist clinicians in conducting forensic risk assessment in child maltreatment cases. The authors present up-to-date research findings and provide practical, fact-based information on key issues. The book serves as a reference source on procedural issues, treatment options, and risk…

TPV Power Source Using Infrared-Sensitive Cells with Commercially Available Radiant Tube Burner

NASA Astrophysics Data System (ADS)

Fraas, Lewis; Minkin, Leonid; Hui, She; Avery, James; Howells, Christopher

2004-11-01

Over the last several years, JX Crystals has invented and systematically developed the key components for thermophotovoltaic systems. These key components include GaSb infrared sensitive cells, high power density shingle circuits, dielectric filters, and hydrocarbon-fueled radiant tube burners. Most recently, we invented and demonstrated an antireflection (AR)-coated tungsten IR emitter which when integrated with the other key components should make TPV systems with efficiencies over 10% practical. However, the use of the AR tungsten emitter requires an oxygen-free hermetic seal enclosure. During a 2003 Small Business Innovative Research (SBIR) Phase I contract, we integrated a tungsten emitter foil and a commercial SiC radiant tube burner within an emitter thermos and successfully demonstrated its operation at high temperature. We also designed a complete stand alone 500 W TPV generator. During the upcoming SBIR Phase II, we plan to implement this design in hardware.

Important sources and chemical species of ambient fine particles related to adverse health effects

NASA Astrophysics Data System (ADS)

Heo, J.

2017-12-01

Although many epidemiological studies have reported that exposure to ambient fine particulate matter (PM2.5) has been linked to increases in mortality and mobidity health outcomes, the key question of which chemical species and sources of PM2.5 are most harmful to public health remains unanswered in the air pollution research area. This study was designed to address the key question with evaluating the risks of exposure to chemical species and source-specific PM2.5 mass on morbidity. Hourly measurements of PM2.5 mass and its major chemical species, including organic carbon, elemental carbon, ions, and trace elements, were observed from January 1 to December 31, 2013 at four of the PM2.5 supersites in urban environments in Korea and the reuslts were used in a positive matrix factorization to estimate source contributions to PM2.5 mass. Nine sources, including secondary sulfate, secondary nitrate, mobile, biomass burning, roadway emission, industry, oil combustion, soil, and aged sea salt, were identified and secondary inorganic aerosol factors (i.e. secondary sulfalte, and secondary nitrate) were the dominant sources contributing to 40% of the total PM2.5 mass in the study region. In order to evaluate the risks of exposure to chemical species and sources of PM2.5 on morbidity, emergency room visits for cardivascular disease and respiratory disease were considered. Hourly health outcomes were compared with hourly measurments of the PM2.5 chemical species and sources using a poission generalized linear model incorporating natural splines, as well as time-stratified case-crossover design. The PM2.5 mass and speveral chemical components, such as organic carbon, elemetal carbon, zinc, and potassium, were strongly associated with morbidity. Source-apporitionmened PM2.5 mass derived from biomass burning, and mobile sources, was significantly associated with cardiovascular and respiratory diseases. The findings represent that local combustion may be particularly important contributor to PM2.5, leading to adverse human health effects.

Solar neutrino detectors as sterile neutrino hunters

NASA Astrophysics Data System (ADS)

Pallavicini, Marco; Borexino-SOX Collaboration; Agostini, M.; Altenmüller, K.; Appel, S.; Atroshchenko, V.; Bellini, G.; Benziger, J.; Berton, N.; Bick, D.; Bonfini, G.; Bravo, D.; Caccianiga, B.; Calaprice, F.; Caminata, A.; Carlini, M.; Cavalcante, P.; Chepurnov, A.; Choi, K.; Cloué, O.; Cribier, M.; D'Angelo, D.; Davini, S.; Derbin, A.; Di Noto, L.; Drachnev, I.; Durero, M.; Etenko, A.; Farinon, S.; Fischer, V.; Fomenko, K.; Franco, D.; Gabriele, F.; Gaffiot, J.; Galbiati, C.; Gschwender, M.; Ghiano, C.; Giammarchi, M.; Goeger-Neff, M.; Goretti, A.; Gromov, M.; Hagner, C.; Houdy, Th.; Hungerford, E.; Ianni, Aldo; Ianni, Andrea; Jany, A.; Jedrzejczak, K.; Jeschke, D.; Jonquères, N.; Kobychev, V.; Korablev, D.; Korga, G.; Kornoukhov, V.; Kryn, D.; Lachenmaier, T.; Lasserre, T.; Laubenstein, M.; Lehnert, B.; Link, J.; Litvinovich, E.; Lombardi, F.; Lombardi, P.; Ludhova, L.; Lukyanchenko, G.; Machulin, I.; Manecki, S.; Maneschg, W.; Marcocci, S.; Maricic, J.; Mention, G.; Meroni, E.; Meyer, M.; Miramonti, L.; Misiaszek, M.; Montuschi, M.; Mosteiro, P.; Muratova, V.; Musenich, R.; Neumair, B.; Oberauer, L.; Ortica, F.; Papp, L.; Pocar, A.; Ranucci, G.; Razeto, A.; Re, A.; Reinert, Y.; Romani, A.; Roncin, R.; Rossi, N.; Schönert, S.; Scola, L.; Semenov, D.; Skorokhvatov, M.; Smirnov, O.; Sotnikov, A.; Suvorov, Y.; Tartaglia, R.; Testera, G.; Thurn, J.; Toropova, M.; Unzhakov, E.; Veyssière, C.; Vishneva, A.; Vivier, M.; Vogelaar, R. B.; von Feilitzsch, F.; Wang, H.; Weinz, S.; Winter, J.; Wojcik, M.; Wurm, M.; Yokley, Z.; Zaimidoroga, O.; Zavatarelli, S.; Zuber, K.; Zuzel, G.

2017-09-01

The large size and the very low radioactive background of solar neutrino detectors such as Borexino at the Gran Sasso Laboratory in Italy offer a unique opportunity to probe the existence of neutrino oscillations into new sterile components by means of carefully designed and well calibrated anti-neutrino and neutrino artificial sources. In this paper we briefly summarise the key elements of the SOX experiment, a program for the search of sterile neutrinos (and other short distance effects) by means of a 144Ce-144Pr anti-neutrino source and, possibly in the medium term future, with a 51Cr neutrino source.

Quasi-experimental study designs series-paper 9: collecting data from quasi-experimental studies.

PubMed

Aloe, Ariel M; Becker, Betsy Jane; Duvendack, Maren; Valentine, Jeffrey C; Shemilt, Ian; Waddington, Hugh

2017-09-01

To identify variables that must be coded when synthesizing primary studies that use quasi-experimental designs. All quasi-experimental (QE) designs. When designing a systematic review of QE studies, potential sources of heterogeneity-both theory-based and methodological-must be identified. We outline key components of inclusion criteria for syntheses of quasi-experimental studies. We provide recommendations for coding content-relevant and methodological variables and outlined the distinction between bivariate effect sizes and partial (i.e., adjusted) effect sizes. Designs used and controls used are viewed as of greatest importance. Potential sources of bias and confounding are also addressed. Careful consideration must be given to inclusion criteria and the coding of theoretical and methodological variables during the design phase of a synthesis of quasi-experimental studies. The success of the meta-regression analysis relies on the data available to the meta-analyst. Omission of critical moderator variables (i.e., effect modifiers) will undermine the conclusions of a meta-analysis. Copyright © 2017 Elsevier Inc. All rights reserved.

A Survey of Usability Practices in Free/Libre/Open Source Software

NASA Astrophysics Data System (ADS)

Paul, Celeste Lyn

A review of case studies about usability in eight Free/Libre/Open Source Software (FLOSS) projects showed that an important issue regarding a usability initiative in the project was the lack of user research. User research is a key component in the user-centered design (UCD) process and a necessary step for creating usable products. Reasons why FLOSS projects suffered from a lack of user research included poor or unclear project leadership, cultural differences between developer and designers, and a lack of usability engineers. By identifying these critical issues, the FLOSS usability community can begin addressing problems in the efficacy of usability activities and work towards creating more usable FLOSS products.

2015 Key Wind Program and National Laboratory Accomplishments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Office of Energy Efficiency and Renewable Energy

The U.S. Department of Energy (DOE) Wind Program is committed to helping the nation secure cost-competitive sources of renewable energy through the development and deployment of innovative wind power technologies. By investing in improvements to wind plant design, technology development, and operation as well as developing tools to identify the highest quality wind resources, the Wind Program serves as a leader in making wind energy technologies more competitive with traditional sources of energy and a larger part of our nation’s renewable energy portfolio.

Approaches to a global quantum key distribution network

NASA Astrophysics Data System (ADS)

Islam, Tanvirul; Bedington, Robert; Ling, Alexander

2017-10-01

Progress in realising quantum computers threatens to weaken existing public key encryption infrastructure. A global quantum key distribution (QKD) network can play a role in computational attack-resistant encryption. Such a network could use a constellation of high altitude platforms such as airships and satellites as trusted nodes to facilitate QKD between any two points on the globe on demand. This requires both space-to-ground and inter-platform links. However, the prohibitive cost of traditional satellite based development limits the experimental work demonstrating relevant technologies. To accelerate progress towards a global network, we use an emerging class of shoe-box sized spacecraft known as CubeSats. We have designed a polarization entangled photon pair source that can operate on board CubeSats. The robustness and miniature form factor of our entanglement source makes it especially suitable for performing pathfinder missions that studies QKD between two high altitude platforms. The technological outcomes of such mission would be the essential building blocks for a global QKD network.

On an efficient multilevel inverter assembly: structural savings and design optimisations

NASA Astrophysics Data System (ADS)

Choupan, Reza; Nazarpour, Daryoush; Golshannavaz, Sajjad

2018-01-01

This study puts forward an efficient unit cell to be taken in use in multilevel inverter assemblies. The proposed structure is in line with reductions in number of direct current (dc) voltage sources, insulated-gate bipolar transistors (IGBTs), gate driver circuits, installation area, and hence the implementation costs. Such structural savings do not sacrifice the technical performance of the proposed design wherein an increased number of output voltage levels is attained, interestingly. Targeting a techno-economic characteristic, the contemplated structure is included as the key unit of cascaded multilevel inverters. Such extensions require development of applicable design procedures. To this end, two efficient strategies are elaborated to determine the magnitudes of input dc voltage sources. As well, an optimisation process is developed to explore the optimal allocation of different parameters in overall performance of the proposed inverter. These parameters are investigated as the number of IGBTs, dc sources, diodes, and overall blocked voltage on switches. In the lights of these characteristics, a comprehensive analysis is established to compare the proposed design with the conventional and recently developed structures. Detailed simulation and experimental studies are conducted to assess the performance of the proposed design. The obtained results are discussed in depth.

A Requirements-Driven Optimization Method for Acoustic Treatment Design

NASA Technical Reports Server (NTRS)

Berton, Jeffrey J.

2016-01-01

Acoustic treatment designers have long been able to target specific noise sources inside turbofan engines. Facesheet porosity and cavity depth are key design variables of perforate-over-honeycomb liners that determine levels of noise suppression as well as the frequencies at which suppression occurs. Layers of these structures can be combined to create a robust attenuation spectrum that covers a wide range of frequencies. Looking to the future, rapidly-emerging additive manufacturing technologies are enabling new liners with multiple degrees of freedom, and new adaptive liners with variable impedance are showing promise. More than ever, there is greater flexibility and freedom in liner design. Subject to practical considerations, liner design variables may be manipulated to achieve a target attenuation spectrum. But characteristics of the ideal attenuation spectrum can be difficult to know. Many multidisciplinary system effects govern how engine noise sources contribute to community noise. Given a hardwall fan noise source to be suppressed, and using an analytical certification noise model to compute a community noise measure of merit, the optimal attenuation spectrum can be derived using multidisciplinary systems analysis methods. The subject of this paper is an analytical method that derives the ideal target attenuation spectrum that minimizes noise perceived by observers on the ground.

Defence Reporter. Spring 2012

DTIC Science & Technology

2012-01-01

procedures and techniques for dealing with disruptive events. R0002869D Visualisation Techniques: Communicating Results to Senior Decision-Makers Dstl...understanding and accurate recall of key information. Open-source literature provides evidence that good visualisations aid effective communication...of abstract or complex information. General principles regarding the design of visualisations for use in presentations or reports are provided. Best

Comparing OECD PISA Reading in English to Other Languages: Identifying Potential Sources of Non-Invariance

ERIC Educational Resources Information Center

Asil, Mustafa; Brown, Gavin T. L.

2016-01-01

The use of the Programme for International Student Assessment (PISA) across nations, cultures, and languages has been criticized. The key criticisms point to the linguistic and cultural biases potentially underlying the design of reading comprehension tests, raising doubts about the legitimacy of comparisons across economies. Our research focused…

Generation and analysis of correlated pairs of photons on board a nanosatellite

NASA Astrophysics Data System (ADS)

Chandrasekara, R.; Tang, Z.; Tan, Y. C.; Cheng, C.; Sha, L.; Hiang, G. C.; Oi, D.; Ling, A.

2016-10-01

Progress in quantum computers and their threat to conventional public key infrastructure is driving new forms of encryption. Quantum Key Distribution (QKD) using entangled photons is a promising approach. A global QKD network can be achieved using satellites equipped with optical links. Despite numerous proposals, actual experimental work demonstrating relevant entanglement technology in space is limited due to the prohibitive cost of traditional satellite development. To make progress, we have designed a photon pair source that can operate on modular spacecraft called CubeSats. We report the in-orbit operation of the photon pair source on board an orbiting CubeSat and demonstrate pair generation and polarisation correlation under space conditions. The in-orbit polarisation correlations are compatible with ground-based tests, validating our design. This successful demonstration is a major experimental milestone towards a space-based quantum network. Our approach provides a cost-effective method for proving the space-worthiness of critical components used in entangled photon technology. We expect that it will also accelerate efforts to probe the overlap between quantum and relativistic models of physics.

User-Centered Design and Printed Educational Materials: A Focus Group Study of Primary Care Physician Preferences.

PubMed

Grudniewicz, Agnes; Bhattacharyya, Onil; McKibbon, K Ann; Straus, Sharon E

2016-01-01

It is challenging for primary care physicians (PCPs) to review and apply the growing amount of clinical evidence available. Printed educational materials (PEMs), which synthesize evidence, are often ineffective at improving knowledge, possibly due to poor design and limited uptake. In this study, we collected PCP preferences for the design and content of physician-oriented PEMs and determined key attributes that may increase their usability and uptake. We held 90-minute focus groups with PCPs in Toronto, ON, Canada. Focus groups included discussion about whether and how participants use PEMs, feedback on three examples of PEMs, and a discussion on general format and design preferences in PEMs. We analyzed focus group transcripts using a thematic analysis and summarized results in a list of user preferences. Four focus groups were held with 13 PCPs. We found that participants only read PEMs relevant to their patients and prefer short, concise documents, with links to sources that can provide more detailed information. Simplicity of materials was important, with many participants preferring PEMs without lengthy backgrounds or scientific explanations. Most participants wanted to see key messages highlighted to easily assess the relevance of the materials to their practice. Some participants shared physician-oriented PEMs with patients. This study shows that PCPs may prefer shorter, simpler, and more concise documents that have less scientific detail but provide references to further information sources. It is important to understand end user preferences for the design and content of these materials to enhance their uptake.

OVERVIEW OF MONO-ENERGETIC GAMMA-RAY SOURCES & APPLICATIONS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hartemann, F V; Albert, F; Anderson, G G

2010-05-18

Recent progress in accelerator physics and laser technology have enabled the development of a new class of tunable gamma-ray light sources based on Compton scattering between a high-brightness, relativistic electron beam and a high intensity laser pulse produced via chirped-pulse amplification (CPA). A precision, tunable Mono-Energetic Gamma-ray (MEGa-ray) source driven by a compact, high-gradient X-band linac is currently under development and construction at LLNL. High-brightness, relativistic electron bunches produced by an X-band linac designed in collaboration with SLAC NAL will interact with a Joule-class, 10 ps, diode-pumped CPA laser pulse to generate tunable {gamma}-rays in the 0.5-2.5 MeV photon energymore » range via Compton scattering. This MEGa-ray source will be used to excite nuclear resonance fluorescence in various isotopes. Applications include homeland security, stockpile science and surveillance, nuclear fuel assay, and waste imaging and assay. The source design, key parameters, and current status are presented, along with important applications, including nuclear resonance fluorescence. In conclusion, we have optimized the design of a high brightness Compton scattering gamma-ray source, specifically designed for NRF applications. Two different parameters sets have been considered: one where the number of photons scattered in a single shot reaches approximately 7.5 x 10{sup 8}, with a focal spot size around 8 {micro}m; in the second set, the spectral brightness is optimized by using a 20 {micro}m spot size, with 0.2% relative bandwidth.« less

Preventing Airborne Disease Transmission: Review of Methods for Ventilation Design in Health Care Facilities

PubMed Central

Aliabadi, Amir A.; Rogak, Steven N.; Bartlett, Karen H.; Green, Sheldon I.

2011-01-01

Health care facility ventilation design greatly affects disease transmission by aerosols. The desire to control infection in hospitals and at the same time to reduce their carbon footprint motivates the use of unconventional solutions for building design and associated control measures. This paper considers indoor sources and types of infectious aerosols, and pathogen viability and infectivity behaviors in response to environmental conditions. Aerosol dispersion, heat and mass transfer, deposition in the respiratory tract, and infection mechanisms are discussed, with an emphasis on experimental and modeling approaches. Key building design parameters are described that include types of ventilation systems (mixing, displacement, natural and hybrid), air exchange rate, temperature and relative humidity, air flow distribution structure, occupancy, engineered disinfection of air (filtration and UV radiation), and architectural programming (source and activity management) for health care facilities. The paper describes major findings and suggests future research needs in methods for ventilation design of health care facilities to prevent airborne infection risk. PMID:22162813

Preventing airborne disease transmission: review of methods for ventilation design in health care facilities.

PubMed

Aliabadi, Amir A; Rogak, Steven N; Bartlett, Karen H; Green, Sheldon I

2011-01-01

Health care facility ventilation design greatly affects disease transmission by aerosols. The desire to control infection in hospitals and at the same time to reduce their carbon footprint motivates the use of unconventional solutions for building design and associated control measures. This paper considers indoor sources and types of infectious aerosols, and pathogen viability and infectivity behaviors in response to environmental conditions. Aerosol dispersion, heat and mass transfer, deposition in the respiratory tract, and infection mechanisms are discussed, with an emphasis on experimental and modeling approaches. Key building design parameters are described that include types of ventilation systems (mixing, displacement, natural and hybrid), air exchange rate, temperature and relative humidity, air flow distribution structure, occupancy, engineered disinfection of air (filtration and UV radiation), and architectural programming (source and activity management) for health care facilities. The paper describes major findings and suggests future research needs in methods for ventilation design of health care facilities to prevent airborne infection risk.

Design and development of the mobile game based on the J2ME technology

NASA Astrophysics Data System (ADS)

He, Junhua

2011-12-01

With the continuous improvement of mobile performance, mobile entertainment applications market trend has been increasingly clear, mobile entertainment applications will be after the PC entertainment applications is another important business growth. Through the full analysis of the current mobile entertainment applications market demand and trends, the author has accumulated a lot of theoretical knowledge and practical experience. Rational, using of some new technology for a mobile entertainment games design, and described the development of key technologies required for mobile game an analysis and design of the game, and to achieve a complete game development. Light of the specific mobile game project - "Battle City", detailed the development of a mobile game based on the J2ME platform, the basic steps and the various key elements, focusing on how to use object-oriented thinking on the role of mobile phones in the abstract and Game Animation package, the source code with specific instructions.

Design and development of the mobile game based on the J2ME technology

NASA Astrophysics Data System (ADS)

He, JunHua

2012-01-01

With the continuous improvement of mobile performance, mobile entertainment applications market trend has been increasingly clear, mobile entertainment applications will be after the PC entertainment applications is another important business growth. Through the full analysis of the current mobile entertainment applications market demand and trends, the author has accumulated a lot of theoretical knowledge and practical experience. Rational, using of some new technology for a mobile entertainment games design, and described the development of key technologies required for mobile game an analysis and design of the game, and to achieve a complete game development. Light of the specific mobile game project - "Battle City", detailed the development of a mobile game based on the J2ME platform, the basic steps and the various key elements, focusing on how to use object-oriented thinking on the role of mobile phones in the abstract and Game Animation package, the source code with specific instructions.

Design of the Familial Hypercholesterolaemia Australasia Network Registry: Creating Opportunities for Greater International Collaboration.

PubMed

Bellgard, Matthew I; Walker, Caroline E; Napier, Kathryn R; Lamont, Leanne; Hunter, Adam A; Render, Lee; Radochonski, Maciej; Pang, Jing; Pedrotti, Annette; Sullivan, David R; Kostner, Karam; Bishop, Warrick; George, Peter M; O'Brien, Richard C; Clifton, Peter M; Bockxmeer, Frank M Van; Nicholls, Stephen J; Hamilton-Craig, Ian; Dawkins, Hugh Js; Watts, Gerald F

2017-10-01

Familial Hypercholesterolemia (FH) is the most common and serious monogenic disorder of lipoprotein metabolism that leads to premature coronary heart disease. There are over 65,000 people estimated to have FH in Australia, but many remain undiagnosed. Patients with FH are often under-treated, but with early detection, cascade family testing and adequate treatment, patient outcomes can improve. Patient registries are key tools for providing new information on FH and enhancing care worldwide. The development and design of the FH Australasia Network Registry is a crucial component in the comprehensive model of care for FH, which aims to provide a standardized, high-quality and cost-effective system of care that is likely to have the highest impact on patient outcomes. Informed by stakeholder engagement, the FH Australasia Network Registry was collaboratively developed by government, patient and clinical networks and research groups. The open-source, web-based Rare Disease Registry Framework was the architecture chosen for this registry owing to its open-source standards, modular design, interoperability, scalability and security features; all these are key components required to meet the ever changing clinical demands across regions. This paper provides a high level blueprint for other countries and jurisdictions to help inform and map out the critical features of an FH registry to meet their particular health system needs.

Enabling three-dimensional densitometric measurements using laboratory source X-ray micro-computed tomography

NASA Astrophysics Data System (ADS)

Pankhurst, M. J.; Fowler, R.; Courtois, L.; Nonni, S.; Zuddas, F.; Atwood, R. C.; Davis, G. R.; Lee, P. D.

2018-01-01

We present new software allowing significantly improved quantitative mapping of the three-dimensional density distribution of objects using laboratory source polychromatic X-rays via a beam characterisation approach (c.f. filtering or comparison to phantoms). One key advantage is that a precise representation of the specimen material is not required. The method exploits well-established, widely available, non-destructive and increasingly accessible laboratory-source X-ray tomography. Beam characterisation is performed in two stages: (1) projection data are collected through a range of known materials utilising a novel hardware design integrated into the rotation stage; and (2) a Python code optimises a spectral response model of the system. We provide hardware designs for use with a rotation stage able to be tilted, yet the concept is easily adaptable to virtually any laboratory system and sample, and implicitly corrects the image artefact known as beam hardening.

Three-color Sagnac source of polarization-entangled photon pairs.

PubMed

Hentschel, Michael; Hübel, Hannes; Poppe, Andreas; Zeilinger, Anton

2009-12-07

We demonstrate a compact and stable source of polarization-entangled pairs of photons, one at 810 nm wavelength for high detection efficiency and the other at 1550 nm for long-distance fiber communication networks. Due to a novel Sagnac-based design of the interferometer no active stabilization is needed. Using only one 30 mm ppKTP bulk crystal the source produces photons with a spectral brightness of 1.13 x 10(6) pairs/s/mW/THz with an entanglement fidelity of 98.2%. Both photons are single-mode fiber coupled and ready to be used in quantum key distribution (QKD) or transmission of photonic quantum states over large distances.

New reversing freeform lens design method for LED uniform illumination with extended source and near field

NASA Astrophysics Data System (ADS)

Zhao, Zhili; Zhang, Honghai; Zheng, Huai; Liu, Sheng

2018-03-01

In light-emitting diode (LED) array illumination (e.g. LED backlighting), obtainment of high uniformity in the harsh condition of the large distance height ratio (DHR), extended source and near field is a key as well as challenging issue. In this study, we present a new reversing freeform lens design algorithm based on the illuminance distribution function (IDF) instead of the traditional light intensity distribution, which allows uniform LED illumination in the above mentioned harsh conditions. IDF of freeform lens can be obtained by the proposed mathematical method, considering the effects of large DHR, extended source and near field target at the same time. In order to prove the claims, a slim direct-lit LED backlighting with DHR equal to 4 is designed. In comparison with the traditional lenses, illuminance uniformity of LED backlighting with the new lens increases significantly from 0.45 to 0.84, and CV(RMSE) decreases dramatically from 0.24 to 0.03 in the harsh condition. Meanwhile, luminance uniformity of LED backlighting with the new lens is obtained as high as 0.92 at the condition of extended source and near field. This new method provides a practical and effective way to solve the problem of large DHR, extended source and near field for LED array illumination.

Two-step design method for highly compact three-dimensional freeform optical system for LED surface light source.

PubMed

Mao, Xianglong; Li, Hongtao; Han, Yanjun; Luo, Yi

2014-10-20

Designing an illumination system for a surface light source with a strict compactness requirement is quite challenging, especially for the general three-dimensional (3D) case. In accordance with the two key features of an expected illumination distribution, i.e., a well-controlled boundary and a precise illumination pattern, a two-step design method is proposed in this paper for highly compact 3D freeform illumination systems. In the first step, a target shape scaling strategy is combined with an iterative feedback modification algorithm to generate an optimized freeform optical system with a well-controlled boundary of the target distribution. In the second step, a set of selected radii of the system obtained in the first step are optimized to further improve the illuminating quality within the target region. The method is quite flexible and effective to design highly compact optical systems with almost no restriction on the shape of the desired target field. As examples, three highly compact freeform lenses with ratio of center height h of the lens and the maximum dimension D of the source ≤ 2.5:1 are designed for LED surface light sources to form a uniform illumination distribution on a rectangular, a cross-shaped and a complex cross pierced target plane respectively. High light control efficiency of η > 0.7 as well as low relative standard illumination deviation of RSD < 0.07 is obtained simultaneously for all the three design examples.

Lessons learned from the SLC

DOE Office of Scientific and Technical Information (OSTI.GOV)

Phinney, N.

The SLAC Linear Collider (SLC) is the first example of an entirely new type of lepton collider. Many years of effort were required to develop the understanding and techniques needed to approach design luminosity. This paper discusses some of the key issues and problems encountered in producing a working linear collider. These include the polarized source, techniques for emittance preservation, extensive feedback systems, and refinements in beam optimization in the final focus. The SLC experience has been invaluable for testing concepts and developing designs for a future linear collider.

Results from a Grazing Incidence X-Ray Interferometer

NASA Technical Reports Server (NTRS)

Joy, Marshall K.; Shipley, Ann; Cash, Webster; Carter, James

2000-01-01

A prototype grazing incidence interferometer has been built and tested at EUV and X-ray wavelengths using a 120 meter long vacuum test facility at Marshall Space Flight Center. We describe the design and construction of the interferometer, the EUV and x-ray sources, the detector systems, and compare the interferometric fringe measurements with theoretical predictions. We also describe the next-generation grazing incidence system which is designed to provide laboratory demonstration of key technologies that will be needed for a space-based x-ray interferometer.

Dynamic robustness of knowledge collaboration network of open source product development community

NASA Astrophysics Data System (ADS)

Zhou, Hong-Li; Zhang, Xiao-Dong

2018-01-01

As an emergent innovative design style, open source product development communities are characterized by a self-organizing, mass collaborative, networked structure. The robustness of the community is critical to its performance. Using the complex network modeling method, the knowledge collaboration network of the community is formulated, and the robustness of the network is systematically and dynamically studied. The characteristics of the network along the development period determine that its robustness should be studied from three time stages: the start-up, development and mature stages of the network. Five kinds of user-loss pattern are designed, to assess the network's robustness under different situations in each of these three time stages. Two indexes - the largest connected component and the network efficiency - are used to evaluate the robustness of the community. The proposed approach is applied in an existing open source car design community. The results indicate that the knowledge collaboration networks show different levels of robustness in different stages and different user loss patterns. Such analysis can be applied to provide protection strategies for the key users involved in knowledge dissemination and knowledge contribution at different stages of the network, thereby promoting the sustainable and stable development of the open source community.

3 CFR 13526 - Executive Order 13526 of December 29, 2009. Classified National Security Information

Code of Federal Regulations, 2010 CFR

2010-01-01

... of weapons of mass destruction. Sec. 1.5. Duration of Classification. (a) At the time of original... intelligence source or key design concepts of weapons of mass destruction, the date or event shall not exceed the time frame established in paragraph (b) of this section. (b) If the original classification...

WISE: Winning with Stronger Education. ACCESS Research Final Report [and] Executive Summary.

ERIC Educational Resources Information Center

Carciun & Associates, Anchorage, AK.

The Winning with Stronger Education Project (WISE) was designed to develop new ways of educating and training the multicultural population of Anchorage, Alaska. Data were obtained from several sources: a mail survey of 1,600 Anchorage residents (which procured a 62 response rate); personal interviews with 25 key Alaska business leaders; a…

Putting Connectivist Principles into Practice: A Case Study of an Online Tertiary Course

ERIC Educational Resources Information Center

Armatas, Christine; Spratt, Christine; Vincent, Andrew

2014-01-01

The Bachelor of Enterprise Learning is a newly accredited undergraduate degree where connectivist principles have been used to guide design of active, student-centered learning activities. A key feature of the curriculum is that it incorporates technology as both a source of information and a tool. Examples from this course are provided in this…

Excellence in Educational Fund Raising at America's Community Colleges and a Key Resources Guide for Educational Fund Raising.

ERIC Educational Resources Information Center

Ryan, G. Jeremiah

Designed to encourage and inform community college efforts to secure private financial support, this literature review and resource guide examine the current status of fund raising at community colleges and list pertinent information sources. After introductory comments advocate increased community college involvement in fund raising, the paper…

Getting Started with The Math Forum Problems of the Week Library. Teacher's Guide

ERIC Educational Resources Information Center

Math Forum @ Drexel, 2009

2009-01-01

The Math Forum Problems of the Week Library is designed to leverage the power of interactive technology to hold student interest while increasing their success as strategic thinkers. The Math Forum Library is an online source of non-routine challenges in which problem solving and mathematical communication are key elements of every problem. This…

Development of a Technical Data File On the Design and Use of Instructional Systems.

ERIC Educational Resources Information Center

Schumacher, Sanford P.

A technical data file concerned with the technology of Instructional System Development suitable for a variety of users was developed. The file was prepared in a way amenable to later computerized storage and retrieval. General information sources and indexes of highly probable relevance were reviewed with key words and relevant specialty journals…

Calibration techniques and results in the soft X-ray and extreme ultraviolet for components of the Extreme Ultraviolet Explorer Satellite

NASA Technical Reports Server (NTRS)

Malina, Roger F.; Jelinsky, Patrick; Bowyer, Stuart

1986-01-01

The calibration facilities and techniques for the Extreme Ultraviolet Explorer (EUVE) from 44 to 2500 A are described. Key elements include newly designed radiation sources and a collimated monochromatic EUV beam. Sample results for the calibration of the EUVE filters, detectors, gratings, collimators, and optics are summarized.

Models of Community Learning Networks in Canada = Modeles de reseaux d'apprentissage communautaires au Canada.

ERIC Educational Resources Information Center

Human Resources Development Canada, Hull (Quebec). Office of Learning Technologies.

Canada-based community learning networks (CLNs) were examined to provide an operational definition of CLNs, design a framework for their review and analysis, and identify best practices in CLNs. Data were collected from three sources: interviews with 16 key stakeholders in CLNs, literature review, and case studies of five Canadian CLNs. The…

Creative design inspired by biological knowledge: Technologies and methods

NASA Astrophysics Data System (ADS)

Tan, Runhua; Liu, Wei; Cao, Guozhong; Shi, Yuan

2018-05-01

Biological knowledge is becoming an important source of inspiration for developing creative solutions to engineering design problems and even has a huge potential in formulating ideas that can help firms compete successfully in a dynamic market. To identify the technologies and methods that can facilitate the development of biologically inspired creative designs, this research briefly reviews the existing biological-knowledge-based theories and methods and examines the application of biological-knowledge-inspired designs in various fields. Afterward, this research thoroughly examines the four dimensions of key technologies that underlie the biologically inspired design (BID) process. This research then discusses the future development trends of the BID process before presenting the conclusions.

418th Brookhaven Lecture

ScienceCinema

Timur Shaftan

2017-12-09

The NSLS-II project will establish a third-generation light source at Brookhaven Lab, increasing beam-line brightness by 10,000. Achieving and maintaining this will involve tightly focusing the electron beam, providing the most efficient insertion devices, and achieving and maintaining a high electron current. In this talk, the various sub-systems of NSLS-II will be reviewed, and the requirements and key elements of their design will be discussed. In addition, the a small prototype of a light source of a different kind that was developed by the NSLS will also be discussed.

Assume-Guarantee Verification of Source Code with Design-Level Assumptions

NASA Technical Reports Server (NTRS)

Giannakopoulou, Dimitra; Pasareanu, Corina S.; Cobleigh, Jamieson M.

2004-01-01

Model checking is an automated technique that can be used to determine whether a system satisfies certain required properties. To address the 'state explosion' problem associated with this technique, we propose to integrate assume-guarantee verification at different phases of system development. During design, developers build abstract behavioral models of the system components and use them to establish key properties of the system. To increase the scalability of model checking at this level, we have developed techniques that automatically decompose the verification task by generating component assumptions for the properties to hold. The design-level artifacts are subsequently used to guide the implementation of the system, but also to enable more efficient reasoning at the source code-level. In particular we propose to use design-level assumptions to similarly decompose the verification of the actual system implementation. We demonstrate our approach on a significant NASA application, where design-level models were used to identify; and correct a safety property violation, and design-level assumptions allowed us to check successfully that the property was presented by the implementation.

A multi-channel tunable source for atomic sensors

NASA Astrophysics Data System (ADS)

Bigelow, Matthew S.; Roberts, Tony D.; McNeil, Shirley A.; Hawthorne, Todd; Battle, Phil

2015-09-01

We have designed and completed initial testing on a laser source suitable for atomic interferometry from compact, robust, integrated components. Our design is enabled by capitalizing on robust, well-commercialized, low-noise telecom components with high reliability and declining costs which will help to drive the widespread deployment of this system. The key innovation is the combination of current telecom-based fiber laser and modulator technology with periodicallypoled waveguide technology to produce tunable laser light at rubidium D1 and D2 wavelengths (and expandable to other alkalis) using second harmonic generation (SHG). Unlike direct-diode sources, this source is immune to feedback at the Rb line eliminating the need for bulky high-power isolators in the system. In addition, the source has GHz-level frequency agility and in our experiments was found to only be limited by the agility of our RF generator. As a proof-of principle, the source was scanned through the Doppler-broadened Rb D2 absorption line. With this technology, multiple channels can be independently tuned to produce the fields needed for addressing atomic states in atom interferometers and clocks. Thus, this technology could be useful in the development cold-atom inertial sensors and gyroscopes.

Recent Development of IMP ECR Ion Sources

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhao, H.W.; Zhang, Z.M.; Sun, L.T.

2005-03-15

Great efforts have been made to develop highly charged ECR ion sources for application of heavy ion accelerator and atomic physics research at IMP in the past few years. The latest development of ECR ion sources at IMP is briefly reviewed. Intense beams with high and intermediate charge states have been produced from IMP LECR3 by optimization of the ion source conditions including rf frequency extended up to 18GHz. 1.1 emA of Ar8+ and 325 e{mu} A of Ar11+ were produced. Dependence of beam emittance on those key parameters of ECR ion source, beam extraction and space charge compensation weremore » experimentally studied at LECR3. Furthermore, an advanced superconducting ECR ion source named SECRAL is being constructed. SECRAL is designed to operate at rf frequency 18-28GHz with axial mirror magnetic fields 3.6-4.0 Tesla at injection, 2.2 Tesla at extraction and sextupole field 2.0 Tesla at the wall. The superconducting magnet with sextupole and three solenoids was tested in a test-cryostat and 95% of designed fields were reached. Construction status and planed schedule of SECRAL are presented.« less

Design of high-speed optical transmission module with an integrated Ti:Er:LiNbO3 waveguide laser/ LiNbO3 electro-optic modulator

NASA Astrophysics Data System (ADS)

Bai, Yang; Chen, Shufen; Fu, Li; Fang, Wei; Lu, Junjun

2005-01-01

A high bit rate more than 10Gbit/s optical pulse generation device is the key to achieving high-speed and broadband optical fiber communication network system .Now, we propose a novel high-speed optical transmission module(TM) consisting of a Ti:Er:LiNbO3 waveguide laser and a Mach-Zehnder-type encoding modulator on the same Er-doped substrate. According to the standard of ITU-T, we design the 10Gbit/ s transmission module at 1.53μm on the Z cut Y propagation LiNbO3 slice. A dynamic model and the corresponding numerical code are used to analyze the waveguide laser while the electrooptic effect to design the modulator. Meanwhile, the working principle, key technology, typical characteristic parameters of the module are given. The transmission module has a high extinction ratio and a low driving voltage, which supplies the efficient, miniaturized light source for wavelength division multiplexing(WDM) system. In additional, the relation of the laser gain with the cavity parameter, as well as the relation of the bandwidth of the electrooptic modulator with some key factors are discussed .The designed module structure is simulated by BPM software and HFSS software.

A Low Cost Key Agreement Protocol Based on Binary Tree for EPCglobal Class 1 Generation 2 RFID Protocol

NASA Astrophysics Data System (ADS)

Jeng, Albert; Chang, Li-Chung; Chen, Sheng-Hui

There are many protocols proposed for protecting Radio Frequency Identification (RFID) system privacy and security. A number of these protocols are designed for protecting long-term security of RFID system using symmetric key or public key cryptosystem. Others are designed for protecting user anonymity and privacy. In practice, the use of RFID technology often has a short lifespan, such as commodity check out, supply chain management and so on. Furthermore, we know that designing a long-term security architecture to protect the security and privacy of RFID tags information requires a thorough consideration from many different aspects. However, any security enhancement on RFID technology will jack up its cost which may be detrimental to its widespread deployment. Due to the severe constraints of RFID tag resources (e. g., power source, computing power, communication bandwidth) and open air communication nature of RFID usage, it is a great challenge to secure a typical RFID system. For example, computational heavy public key and symmetric key cryptography algorithms (e. g., RSA and AES) may not be suitable or over-killed to protect RFID security or privacy. These factors motivate us to research an efficient and cost effective solution for RFID security and privacy protection. In this paper, we propose a new effective generic binary tree based key agreement protocol (called BKAP) and its variations, and show how it can be applied to secure the low cost and resource constraint RFID system. This BKAP is not a general purpose key agreement protocol rather it is a special purpose protocol to protect privacy, un-traceability and anonymity in a single RFID closed system domain.

Multi-client quantum key distribution using wavelength division multiplexing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grice, Warren P; Bennink, Ryan S; Earl, Dennis Duncan

Quantum Key Distribution (QKD) exploits the rules of quantum mechanics to generate and securely distribute a random sequence of bits to two spatially separated clients. Typically a QKD system can support only a single pair of clients at a time, and so a separate quantum link is required for every pair of users. We overcome this limitation with the design and characterization of a multi-client entangled-photon QKD system with the capacity for up to 100 clients simultaneously. The time-bin entangled QKD system includes a broadband down-conversion source with two unique features that enable the multi-user capability. First, the photons aremore » emitted across a very large portion of the telecom spectrum. Second, and more importantly, the photons are strongly correlated in their energy degree of freedom. Using standard wavelength division multiplexing (WDM) hardware, the photons can be routed to different parties on a quantum communication network, while the strong spectral correlations ensure that each client is linked only to the client receiving the conjugate wavelength. In this way, a single down-conversion source can support dozens of channels simultaneously--and to the extent that the WDM hardware can send different spectral channels to different clients, the system can support multiple client pairings. We will describe the design and characterization of the down-conversion source, as well as the client stations, which must be tunable across the emission spectrum.« less

A modular approach to disease registry design: successful adoption of an internet-based rare disease registry.

PubMed

Bellgard, Matthew I; Macgregor, Andrew; Janon, Fred; Harvey, Adam; O'Leary, Peter; Hunter, Adam; Dawkins, Hugh

2012-10-01

There is a need to develop Internet-based rare disease registries to support health care stakeholders to deliver improved quality patient outcomes. Such systems should be architected to enable multiple-level access by a range of user groups within a region or across regional/country borders in a secure and private way. However, this functionality is currently not available in many existing systems. A new approach to the design of an Internet-based architecture for disease registries has been developed for patients with clinical and genetic data in geographical disparate locations. The system addresses issues of multiple-level access by key stakeholders, security and privacy. The system has been successfully adopted for specific rare diseases in Australia and is open source. The results of this work demonstrate that it is feasible to design an open source Internet-based disease registry system in a scalable and customizable fashion and designed to facilitate interoperability with other systems. © 2012 Wiley Periodicals, Inc.

Direct design of achromatic lens for Lambertian sources in collimating illumination

NASA Astrophysics Data System (ADS)

Yin, Peng; Xu, Xiping; Jiang, Zhaoguo; Wang, Hongshu

2017-10-01

Illumination design used to redistribute the spatial energy distribution of light source is a key technique in lighting applications. However, there is still no effective illumination design method for the removing of the chromatic dispersion. What we present here is an achromatic lens design to enhance the efficiency and uniform illumination of white light-emitting diode (LED) with diffractive optical element (DOE). We employ the chromatic aberration value (deg) to measure the degree of chromatic dispersion in illumination systems. Monte Carlo ray tracing simulation results indicate that the chromatic dispersion of the modified achromatic collimator significantly decreases from 0.5 to 0.1 with LED chip size of 1.0mm×1.0mm and simulation efficiency of 90.73%, compared with the traditional collimator. Moreover, with different corrected wavelengths we compared different chromatic aberration values that followed with the changing pupil percent. The achromatic collimator provided an effective way to achieve white LED with low chromatic dispersion at high efficiency and uniform illumination.

Overview of the ISOL facility for the RISP

NASA Astrophysics Data System (ADS)

Woo, H. J.; Kang, B. H.; Tshoo, K.; Seo, C. S.; Hwang, W.; Park, Y.-H.; Yoon, J. W.; Yoo, S. H.; Kim, Y. K.; Jang, D. Y.

2015-02-01

The key feature of the Isotope Separation On-Line (ISOL) facility is its ability to provide high-intensity and high-quality beams of neutron-rich isotopes with masses in the range of 80-160 by means of a 70-MeV proton beam directly impinging on uranium-carbide thin-disc targets to perform forefront research in nuclear structure, nuclear astrophysics, reaction dynamics and interdisciplinary fields like medical, biological and material sciences. The technical design of the 10-kW and the 35-kW direct fission targets with in-target fission rates of up to 1014 fissions/s has been finished, and for the development of the ISOL fission-target chemistry an initial effort has been made to produce porous lanthanum-carbide (LaCx) discs as a benchmark for the final production of porous UCx discs. For the production of various beams, three classes of ion sources are under development at RISP (Rare Isotope Science Project), the surface ion source, the plasma ion source (FEBIAD), the laser ion source, and the engineering design of the FEBIAD is in progress for prototype fabrication. The engineering design of the ISOL target/ion source front-end system is also in progress, and a prototype will be used for an off-line test facility in front of the pre-separator. The technical designs of other basic elements at the ISOL facility, such as the RF-cooler, the high-resolution mass separator, and the A/q separator, have been finished, and the results, along with the future plans, are introduced.

Development of authentication code for multi-access optical code division multiplexing based quantum key distribution

NASA Astrophysics Data System (ADS)

Taiwo, Ambali; Alnassar, Ghusoon; Bakar, M. H. Abu; Khir, M. F. Abdul; Mahdi, Mohd Adzir; Mokhtar, M.

2018-05-01

One-weight authentication code for multi-user quantum key distribution (QKD) is proposed. The code is developed for Optical Code Division Multiplexing (OCDMA) based QKD network. A unique address assigned to individual user, coupled with degrading probability of predicting the source of the qubit transmitted in the channel offer excellent secure mechanism against any form of channel attack on OCDMA based QKD network. Flexibility in design as well as ease of modifying the number of users are equally exceptional quality presented by the code in contrast to Optical Orthogonal Code (OOC) earlier implemented for the same purpose. The code was successfully applied to eight simultaneous users at effective key rate of 32 bps over 27 km transmission distance.

A comprehensive classification method for VOC emission sources to tackle air pollution based on VOC species reactivity and emission amounts.

PubMed

Li, Guohao; Wei, Wei; Shao, Xia; Nie, Lei; Wang, Hailin; Yan, Xiao; Zhang, Rui

2018-05-01

In China, volatile organic compound (VOC) control directives have been continuously released and implemented for important sources and regions to tackle air pollution. The corresponding control requirements were based on VOC emission amounts (EA), but never considered the significant differentiation of VOC species in terms of atmospheric chemical reactivity. This will adversely influence the effect of VOC reduction on air quality improvement. Therefore, this study attempted to develop a comprehensive classification method for typical VOC sources in the Beijing-Tianjin-Hebei region (BTH), by combining the VOC emission amounts with the chemical reactivities of VOC species. Firstly, we obtained the VOC chemical profiles by measuring 5 key sources in the BTH region and referencing another 10 key sources, and estimated the ozone formation potential (OFP) per ton VOC emission for these sources by using the maximum incremental reactivity (MIR) index as the characteristic of source reactivity (SR). Then, we applied the data normalization method to respectively convert EA and SR to normalized EA (NEA) and normalized SR (NSR) for various sources in the BTH region. Finally, the control index (CI) was calculated, and these sources were further classified into four grades based on the normalized CI (NCI). The study results showed that in the BTH region, furniture coating, automobile coating, and road vehicles are characterized by high NCI and need to be given more attention; however, the petro-chemical industry, which was designated as an important control source by air quality managers, has a lower NCI. Copyright © 2017. Published by Elsevier B.V.

Joint Source-Channel Decoding of Variable-Length Codes with Soft Information: A Survey

NASA Astrophysics Data System (ADS)

Guillemot, Christine; Siohan, Pierre

2005-12-01

Multimedia transmission over time-varying wireless channels presents a number of challenges beyond existing capabilities conceived so far for third-generation networks. Efficient quality-of-service (QoS) provisioning for multimedia on these channels may in particular require a loosening and a rethinking of the layer separation principle. In that context, joint source-channel decoding (JSCD) strategies have gained attention as viable alternatives to separate decoding of source and channel codes. A statistical framework based on hidden Markov models (HMM) capturing dependencies between the source and channel coding components sets the foundation for optimal design of techniques of joint decoding of source and channel codes. The problem has been largely addressed in the research community, by considering both fixed-length codes (FLC) and variable-length source codes (VLC) widely used in compression standards. Joint source-channel decoding of VLC raises specific difficulties due to the fact that the segmentation of the received bitstream into source symbols is random. This paper makes a survey of recent theoretical and practical advances in the area of JSCD with soft information of VLC-encoded sources. It first describes the main paths followed for designing efficient estimators for VLC-encoded sources, the key component of the JSCD iterative structure. It then presents the main issues involved in the application of the turbo principle to JSCD of VLC-encoded sources as well as the main approaches to source-controlled channel decoding. This survey terminates by performance illustrations with real image and video decoding systems.

Two dimensional radial gas flows in atmospheric pressure plasma-enhanced chemical vapor deposition

NASA Astrophysics Data System (ADS)

Kim, Gwihyun; Park, Seran; Shin, Hyunsu; Song, Seungho; Oh, Hoon-Jung; Ko, Dae Hong; Choi, Jung-Il; Baik, Seung Jae

2017-12-01

Atmospheric pressure (AP) operation of plasma-enhanced chemical vapor deposition (PECVD) is one of promising concepts for high quality and low cost processing. Atmospheric plasma discharge requires narrow gap configuration, which causes an inherent feature of AP PECVD. Two dimensional radial gas flows in AP PECVD induces radial variation of mass-transport and that of substrate temperature. The opposite trend of these variations would be the key consideration in the development of uniform deposition process. Another inherent feature of AP PECVD is confined plasma discharge, from which volume power density concept is derived as a key parameter for the control of deposition rate. We investigated deposition rate as a function of volume power density, gas flux, source gas partial pressure, hydrogen partial pressure, plasma source frequency, and substrate temperature; and derived a design guideline of deposition tool and process development in terms of deposition rate and uniformity.

Design Comparison of Inner and Outer Rotor of Permanent Magnet Flux Switching Machine for Electric Bicycle Application

NASA Astrophysics Data System (ADS)

Jusoh, L. I.; Sulaiman, E.; Bahrim, F. S.; Kumar, R.

2017-08-01

Recent advancements have led to the development of flux switching machines (FSMs) with flux sources within the stators. The advantage of being a single-piece machine with a robust rotor structure makes FSM an excellent choice for speed applications. There are three categories of FSM, namely, the permanent magnet (PM) FSM, the field excitation (FE) FSM, and the hybrid excitation (HE) FSM. The PMFSM and the FEFSM have their respective PM and field excitation coil (FEC) as their key flux sources. Meanwhile, as the name suggests, the HEFSM has a combination of PM and FECs as the flux sources. The PMFSM is a simple and cheap machine, and it has the ability to control variable flux, which would be suitable for an electric bicycle. Thus, this paper will present a design comparison between an inner rotor and an outer rotor for a single-phase permanent magnet flux switching machine with 8S-10P, designed specifically for an electric bicycle. The performance of this machine was validated using the 2D- FEA. As conclusion, the outer-rotor has much higher torque approximately at 54.2% of an innerrotor PMFSM. From the comprehensive analysis of both designs it can be conclude that output performance is lower than the SRM and IPMSM design machine. But, it shows that the possibility to increase the design performance by using “deterministic optimization method”.

Community health information sources--a survey in three disparate communities.

PubMed

Dart, Jared; Gallois, Cindy; Yellowlees, Peter

2008-02-01

To determine the current utilisation, importance, trust and future preference for contemporary sources of health information in three different socioeconomic groups. A pilot study including key informant interviews and direct observation was conducted in a low socioeconomic community. From this work a survey questionnaire was designed and implemented across three different communities. Semi-structured key informant interviews and focus groups capturing 52 respondents. Paper-based surveys were left in community organisations and local health practices in a low socioeconomic (LSE) community on the outskirts of Ipswich, Queensland, a mid-high socioeconomic (MSE) community in the western suburbs of Brisbane, and at a local university. Rank of current and preferred future sources of health information, importance and trustworthiness of health information sources. Across all three communities the local doctor was the most currently used, important, trusted and preferred future source of health information. The most striking difference between the three communities related to the current use and preferred future use of the internet. The internet was a more currently used source of health information and more important source in the university population than the LSE or MSE populations. It was also a less preferred source of future health information in the LSE population than the MSE or university populations. Importantly, currently used sources of health information did not reflect community members' preferred sources of health information. People in different socioeconomic communities obtain health information from various sources. This may reflect access issues, education and awareness of the internet as a source of health information, less health information seeking as well as a reluctance by the e-health community to address the specific needs of this group.

Transmission line design for the lunar environment

NASA Technical Reports Server (NTRS)

Gaustad, Krista L.; Gordon, Lloyd B.

1990-01-01

How the mass, operating temperature, and efficiency of a transmission line operating on the moon are affected by its operating parameters, the lunar environment, and the choice of materials is examined. The key transmission line parameters which have an effect on mass, operating temperature, and efficiency are voltage, power loss, and waveform. The choice of waveform for transmission will be influenced by the waveform of the source and load, and therefore an analysis of both DC and AC transmission is necessary for a complete understanding of lunar power transmission. The data presented are for the DC case only; however, the discussion of the environmental effects and of material selection is pertinent to both AC and DC transmission. The operating voltage is shown to be a key parameter in transmission line design. The role efficiency plays in transmission line design is also examined. The analyses include above- and below-the-surface operation for both a vacuum-insulated, two-wire, transmission line, and a solid-dielectric-insulated, coaxial, transmission line.

Advanced Compton scattering light source R&D at LLNL

DOE Office of Scientific and Technical Information (OSTI.GOV)

Albert, F; Anderson, S G; Anderson, G

2010-02-16

We report the design and current status of a monoenergetic laser-based Compton scattering 0.5-2.5 MeV {gamma}-ray source. Previous nuclear resonance fluorescence results and future linac and laser developments for the source are presented. At MeV photon energies relevant for nuclear processes, Compton scattering light sources are attractive because of their relative compactness and improved brightness above 100 keV, compared to typical 4th generation synchrotrons. Recent progress in accelerator physics and laser technology have enabled the development of a new class of tunable Mono-Energetic Gamma-Ray (MEGa-Ray) light sources based on Compton scattering between a high-brightness, relativistic electron beam and a highmore » intensity laser pulse produced via chirped-pulse amplification (CPA). A new precision, tunable gamma-ray source driven by a compact, high-gradient X-band linac is currently under development and construction at LLNL. High-brightness, relativistic electron bunches produced by an X-band linac designed in collaboration with SLAC will interact with a Joule-class, 10 ps, diode-pumped CPA laser pulse to generate tunable {gamma}-rays in the 0.5-2.5 MeV photon energy range via Compton scattering. Based on the success of the previous Thomson-Radiated Extreme X-rays (T-REX) Compton scattering source at LLNL, the source will be used to excite nuclear resonance fluorescence lines in various isotopes; applications include homeland security, stockpile science and surveillance, nuclear fuel assay, and waste imaging and assay. After a brief presentation of successful nuclear resonance fluorescence (NRF) experiments done with T-REX, the new source design, key parameters, and current status are presented.« less

Intensity-Modulated Advanced X-ray Source (IMAXS) for Homeland Security Applications

NASA Astrophysics Data System (ADS)

Langeveld, Willem G. J.; Johnson, William A.; Owen, Roger D.; Schonberg, Russell G.

2009-03-01

X-ray cargo inspection systems for the detection and verification of threats and contraband require high x-ray energy and high x-ray intensity to penetrate dense cargo. On the other hand, low intensity is desirable to minimize the radiation footprint. A collaboration between HESCO/PTSE Inc., Schonberg Research Corporation and Rapiscan Laboratories, Inc. has been formed in order to design and build an Intensity-Modulated Advanced X-ray Source (IMAXS). Such a source would allow cargo inspection systems to achieve up to two inches greater imaging penetration capability, while retaining the same average radiation footprint as present fixed-intensity sources. Alternatively, the same penetration capability can be obtained as with conventional sources with a reduction of the average radiation footprint by about a factor of three. The key idea is to change the intensity of the source for each x-ray pulse based on the signal strengths in the inspection system detector array during the previous pulse. In this paper we describe methods to accomplish pulse-to-pulse intensity modulation in both S-band (2998 MHz) and X-band (9303 MHz) linac sources, with diode or triode (gridded) electron guns. The feasibility of these methods has been demonstrated. Additionally, we describe a study of a shielding design that would allow a 6 MV X-band source to be used in mobile applications.

Quantum key distribution without detector vulnerabilities using optically seeded lasers

NASA Astrophysics Data System (ADS)

Comandar, L. C.; Lucamarini, M.; Fröhlich, B.; Dynes, J. F.; Sharpe, A. W.; Tam, S. W.-B.; Yuan, Z. L.; Penty, R. V.; Shields, A. J.

2016-05-01

Security in quantum cryptography is continuously challenged by inventive attacks targeting the real components of a cryptographic set-up, and duly restored by new countermeasures to foil them. Owing to their high sensitivity and complex design, detectors are the most frequently attacked components. It was recently shown that two-photon interference from independent light sources can be used to remove any vulnerability from detectors. This new form of detection-safe quantum key distribution (QKD), termed measurement-device-independent (MDI), has been experimentally demonstrated but with modest key rates. Here, we introduce a new pulsed laser seeding technique to obtain high-visibility interference from gain-switched lasers and thereby perform MDI-QKD with unprecedented key rates in excess of 1 megabit per second in the finite-size regime. This represents a two to six orders of magnitude improvement over existing implementations and supports the new scheme as a practical resource for secure quantum communications.

Physics design of the injector source for ITER neutral beam injector (invited).

PubMed

Antoni, V; Agostinetti, P; Aprile, D; Cavenago, M; Chitarin, G; Fonnesu, N; Marconato, N; Pilan, N; Sartori, E; Serianni, G; Veltri, P

2014-02-01

Two Neutral Beam Injectors (NBI) are foreseen to provide a substantial fraction of the heating power necessary to ignite thermonuclear fusion reactions in ITER. The development of the NBI system at unprecedented parameters (40 A of negative ion current accelerated up to 1 MV) requires the realization of a full scale prototype, to be tested and optimized at the Test Facility under construction in Padova (Italy). The beam source is the key component of the system and the design of the multi-grid accelerator is the goal of a multi-national collaborative effort. In particular, beam steering is a challenging aspect, being a tradeoff between requirements of the optics and real grids with finite thickness and thermo-mechanical constraints due to the cooling needs and the presence of permanent magnets. In the paper, a review of the accelerator physics and an overview of the whole R&D physics program aimed to the development of the injector source are presented.

Status of the 1 MeV Accelerator Design for ITER NBI

NASA Astrophysics Data System (ADS)

Kuriyama, M.; Boilson, D.; Hemsworth, R.; Svensson, L.; Graceffa, J.; Schunke, B.; Decamps, H.; Tanaka, M.; Bonicelli, T.; Masiello, A.; Bigi, M.; Chitarin, G.; Luchetta, A.; Marcuzzi, D.; Pasqualotto, R.; Pomaro, N.; Serianni, G.; Sonato, P.; Toigo, V.; Zaccaria, P.; Kraus, W.; Franzen, P.; Heinemann, B.; Inoue, T.; Watanabe, K.; Kashiwagi, M.; Taniguchi, M.; Tobari, H.; De Esch, H.

2011-09-01

The beam source of neutral beam heating/current drive system for ITER is needed to accelerate the negative ion beam of 40A with D- at 1 MeV for 3600 sec. In order to realize the beam source, design and R&D works are being developed in many institutions under the coordination of ITER organization. The development of the key issues of the ion source including source plasma uniformity, suppression of co-extracted electron in D beam operation and also after the long beam duration time of over a few 100 sec, is progressed mainly in IPP with the facilities of BATMAN, MANITU and RADI. In the near future, ELISE, that will be tested the half size of the ITER ion source, will start the operation in 2011, and then SPIDER, which demonstrates negative ion production and extraction with the same size and same structure as the ITER ion source, will start the operation in 2014 as part of the NBTF. The development of the accelerator is progressed mainly in JAEA with the MeV test facility, and also the computer simulation of beam optics also developed in JAEA, CEA and RFX. The full ITER heating and current drive beam performance will be demonstrated in MITICA, which will start operation in 2016 as part of the NBTF.

Efficient Implementation of High Order Inverse Lax-Wendroff Boundary Treatment for Conservation Laws

DTIC Science & Technology

2011-07-15

with or without source terms representing chemical reactions in detonations . The results demonstrate the designed fifth order accuracy, stability, and...good performance for problems involving complicated interactions between detonation /shock waves and solid boundaries. AMS subject classification... detonation ; no-penetration con- ditions 1Division of Applied Mathematics, Brown University, Providence, RI 02912. E-mail: sirui@dam.brown.edu. 2State Key

Looking at Biotech’s Crystal Ball

PubMed Central

KOBER, SCOTT

2005-01-01

Biotech’s course through 2005 will hinge on five key variables: Use of electronic medical records to speed data collectionClarifying sources of investment capitalKeeping clinicians currentReshaping benefit designs to cope with new and costly productsAnd, above all, defining and proving the value of biotech products Here’s a look at how these issues could play out in the year ahead. PMID:23390402

Designing Wind and Solar Power Purchase Agreements to Support Grid Integration

DOE Office of Scientific and Technical Information (OSTI.GOV)

O'Neill, Barbara; Chernyakhovskiy, Ilya

Power purchase agreements (PPAs) represent one of many institutional tools that power systems can use to improve grid services from variable renewable energy (VRE) generators. This fact sheet introduces the concept of PPAs for VRE generators and provides a brief summary of key PPA components that can facilitate VRE generators to enhance grid stability and serve as a source of power system flexibility.

Key issues in the thermal design of spaceborne cryogenic infrared instruments

NASA Astrophysics Data System (ADS)

Schember, Helene R.; Rapp, Donald

1992-12-01

Thermal design and analysis play an integral role in the development of spaceborne cryogenic infrared (IR) instruments. From conceptual sketches to final testing, both direct and derived thermal requirements place significant constraints on the instrument design. Although in practice these thermal requirements are interdependent, the sources of most thermal constraints may be grouped into six distinct categories. These are: (1) Detector temperatures, (2) Optics temperatures, (3) Pointing or alignment stability, (4) Mission lifetime, (5) Orbit, and (6) Test and Integration. In this paper, we discuss these six sources of thermal requirements with particular regard to development of instrument packages for low background infrared astronomical observatories. In the end, the thermal performance of these instruments must meet a set of thermal requirements. The development of these requirements is typically an ongoing and interactive process, however, and the thermal design must maintain flexibility and robustness throughout the process. The thermal (or cryogenic) engineer must understand the constraints imposed by the science requirements, the specific hardware, the observing environment, the mission design, and the testing program. By balancing these often competing factors, the system-oriented thermal engineer can work together with the experiment team to produce an effective overall design of the instrument.

Designing and implementing an electronic dashboard for disease outbreaks response - Case study of the 2013-2014 Somalia Polio outbreak response dashboard

PubMed Central

Kamadjeu, Raoul; Gathenji, Caroline

2017-01-01

In April 2013, a case of wild polio virus (WPV) was detected in the Somalia capital Mogadishu. This inaugurated what is now referred to as the 2013-2014 Horn of Africa Polio outbreak with cases reported in Somalia, Kenya and Ethiopia. By the notification of the last polio case in August 2014, 223 cases of WPV had been reported in Somalia, Kenya and Ethiopia of which 199 in Somalia alone. The outbreak response required timely exchange of information between the outbreak response coordination unit (in Nairobi) and local staff located in multiple locations inside the country. The need to track and timely respond to information requests, to satisfy the information/data needs of polio partners and to track key outbreak response performance indicators dictated the need to urgently set up an online dashboard. The Somalia Polio Room dashboard provided a graphical display of the polio outbreak data to track progress and inform decision making. The system was designed using free and open sources components and seamlessly integrated existing polio surveillance data for real time monitoring of key outbreak response performance indicators. In this article, we describe the design and operation of an electronic dashboard for disease surveillance in an outbreak situation and used the lessons learned to propose key design considerations and functional requirements for online electronic dashboards for disease outbreak response. PMID:29296157

Designing and implementing an electronic dashboard for disease outbreaks response - Case study of the 2013-2014 Somalia Polio outbreak response dashboard.

PubMed

Kamadjeu, Raoul; Gathenji, Caroline

2017-01-01

In April 2013, a case of wild polio virus (WPV) was detected in the Somalia capital Mogadishu. This inaugurated what is now referred to as the 2013-2014 Horn of Africa Polio outbreak with cases reported in Somalia, Kenya and Ethiopia. By the notification of the last polio case in August 2014, 223 cases of WPV had been reported in Somalia, Kenya and Ethiopia of which 199 in Somalia alone. The outbreak response required timely exchange of information between the outbreak response coordination unit (in Nairobi) and local staff located in multiple locations inside the country. The need to track and timely respond to information requests, to satisfy the information/data needs of polio partners and to track key outbreak response performance indicators dictated the need to urgently set up an online dashboard. The Somalia Polio Room dashboard provided a graphical display of the polio outbreak data to track progress and inform decision making. The system was designed using free and open sources components and seamlessly integrated existing polio surveillance data for real time monitoring of key outbreak response performance indicators. In this article, we describe the design and operation of an electronic dashboard for disease surveillance in an outbreak situation and used the lessons learned to propose key design considerations and functional requirements for online electronic dashboards for disease outbreak response.

Sensing design and workmanship: the haptic skills of shoppers in eighteenth-century London.

PubMed

Smith, Kate

2012-01-01

This article explores how eighteenth-century shoppers understood the material world around them. It argues that retail experiences exposed shoppers to different objects, which subsequently shaped their understanding of this world. This article builds on recent research that highlights the importance of shop environments and browsing in consumer choice. More particularly, it differentiates itself by examining the practice of handling goods in shops and arguing that sensory interaction with multiple goods was one of the key means by which shoppers comprehended concepts of design and workmanship. In doing so, it affirms the importance of sensory research to design history. The article focuses on consumer purchases of ceramic objects and examines a variety of sources to demonstrate the role of haptic skills in this act. It shows how different literary sources described browsing for goods in gendered and satirical terms and then contrasts these readings against visual evidence to illustrate how handling goods was also represented as a positive act. It reads browsing as a valued practice requiring competence, patience and haptic skills. Through an examination of diary sources, letters and objects this article asks what information shoppers gained from touching various objects. It concludes by demonstrating how repetitive handling in search of quality meant that shoppers acquired their own conception of what constituted workmanship and design.

Full-Sun observations for identifying the source of the slow solar wind

PubMed Central

Brooks, David H.; Ugarte-Urra, Ignacio; Warren, Harry P.

2015-01-01

Fast (>700 km s−1) and slow (~400 km s−1) winds stream from the Sun, permeate the heliosphere and influence the near-Earth environment. While the fast wind is known to emanate primarily from polar coronal holes, the source of the slow wind remains unknown. Here we identify possible sites of origin using a slow solar wind source map of the entire Sun, which we construct from specially designed, full-disk observations from the Hinode satellite, and a magnetic field model. Our map provides a full-Sun observation that combines three key ingredients for identifying the sources: velocity, plasma composition and magnetic topology and shows them as solar wind composition plasma outflowing on open magnetic field lines. The area coverage of the identified sources is large enough that the sum of their mass contributions can explain a significant fraction of the mass loss rate of the solar wind. PMID:25562705

Reverse osmosis desalination: water sources, technology, and today's challenges.

PubMed

Greenlee, Lauren F; Lawler, Desmond F; Freeman, Benny D; Marrot, Benoit; Moulin, Philippe

2009-05-01

Reverse osmosis membrane technology has developed over the past 40 years to a 44% share in world desalting production capacity, and an 80% share in the total number of desalination plants installed worldwide. The use of membrane desalination has increased as materials have improved and costs have decreased. Today, reverse osmosis membranes are the leading technology for new desalination installations, and they are applied to a variety of salt water resources using tailored pretreatment and membrane system design. Two distinct branches of reverse osmosis desalination have emerged: seawater reverse osmosis and brackish water reverse osmosis. Differences between the two water sources, including foulants, salinity, waste brine (concentrate) disposal options, and plant location, have created significant differences in process development, implementation, and key technical problems. Pretreatment options are similar for both types of reverse osmosis and depend on the specific components of the water source. Both brackish water and seawater reverse osmosis (RO) will continue to be used worldwide; new technology in energy recovery and renewable energy, as well as innovative plant design, will allow greater use of desalination for inland and rural communities, while providing more affordable water for large coastal cities. A wide variety of research and general information on RO desalination is available; however, a direct comparison of seawater and brackish water RO systems is necessary to highlight similarities and differences in process development. This article brings to light key parameters of an RO process and process modifications due to feed water characteristics.

Design Optimization of Ge/GaAs-Based Heterojunction Gate-All-Around (GAA) Arch-Shaped Tunneling Field-Effect Transistor (A-TFET).

PubMed

Seo, Jae Hwa; Yoon, Young Jun; Kang, In Man

2018-09-01

The Ge/GaAs-based heterojunction gate-all-around (GAA) arch-shaped tunneling field-effect transistor (A-TFET) have been designed and optimized using technology computer-aided design (TCAD) simulations. In our previous work, the silicon-based A-TFET was designed and demonstrated. However, to progress the electrical characteristics of A-TFET, the III-V compound heterojunction structures which has enhanced electrical properties must be adopted. Thus, the germanium with gallium arsenide (Ge/GaAs) is considered as key materials of A-TFET. The proposed device has a Ge-based p-doped source, GaAs-based i-doped channel and GaAs-based n-doped drain. Due to the critical issues of device performances, the doping concentration of source and channel region (Dsource, Dchannel), height of source region (Hsource) and epitaxially grown thickness of channel (tepi) was selected as design optimization variables of Ge/GaAs-based GAA A-TFET. The DC characteristics such as on-state current (ion), off-state current (ioff), subthreshold-swing (S) were of extracted and analyzed. Finally, the proposed device has a gate length (LG) of 90 nm, Dsource 5 × 1019 cm-3, Dchannel of 1018 cm-3, tepi of 4 nm, Hsource of 90 nm, R of 10 nm and demonstrate an ion of 2 mA/μm, S of 12.9 mV/dec.

Journal of Open Source Software (JOSS): design and first-year review

NASA Astrophysics Data System (ADS)

Smith, Arfon M.

2018-01-01

JOSS is a free and open-access journal that publishes articles describing research software across all disciplines. It has the dual goals of improving the quality of the software submitted and providing a mechanism for research software developers to receive credit. While designed to work within the current merit system of science, JOSS addresses the dearth of rewards for key contributions to science made in the form of software. JOSS publishes articles that encapsulate scholarship contained in the software itself, and its rigorous peer review targets the software components: functionality, documentation, tests, continuous integration, and the license. A JOSS article contains an abstract describing the purpose and functionality of the software, references, and a link to the software archive. JOSS published more than 100 articles in its first year, many from the scientific python ecosystem (including a number of articles related to astronomy and astrophysics). JOSS is a sponsored project of the nonprofit organization NumFOCUS and is an affiliate of the Open Source Initiative.In this presentation, I'll describes the motivation, design, and progress of the Journal of Open Source Software (JOSS) and how it compares to other avenues for publishing research software in astronomy.

The GeoViz Toolkit: Using component-oriented coordination methods for geographic visualization and analysis

PubMed Central

Hardisty, Frank; Robinson, Anthony C.

2010-01-01

In this paper we present the GeoViz Toolkit, an open-source, internet-delivered program for geographic visualization and analysis that features a diverse set of software components which can be flexibly combined by users who do not have programming expertise. The design and architecture of the GeoViz Toolkit allows us to address three key research challenges in geovisualization: allowing end users to create their own geovisualization and analysis component set on-the-fly, integrating geovisualization methods with spatial analysis methods, and making geovisualization applications sharable between users. Each of these tasks necessitates a robust yet flexible approach to inter-tool coordination. The coordination strategy we developed for the GeoViz Toolkit, called Introspective Observer Coordination, leverages and combines key advances in software engineering from the last decade: automatic introspection of objects, software design patterns, and reflective invocation of methods. PMID:21731423

Low-cost manufacturing of the point focus concentrating module and its key component, the Fresnel lens. Final subcontract report, 31 January 1991--6 May 1991

DOE Office of Scientific and Technical Information (OSTI.GOV)

Saifee, T.; Konnerth, A. III

1991-11-01

Solar Kinetics, Inc. (SKI) has been developing point-focus concentrating PV modules since 1986. SKI is currently in position to manufacture between 200 to 600 kilowatts annually of the current design by a combination of manual and semi-automated methods. This report reviews the current status of module manufacture and specifies the required approach to achieve a high-volume manufacturing capability and low cost. The approach taken will include process development concurrent with module design for automated manufacturing. The current effort reviews the major manufacturing costs and identifies components and processes whose improvements would produce the greatest effect on manufacturability and cost reduction.more » The Fresnel lens is one such key component. Investigating specific alternative manufacturing methods and sources has substantially reduced the lens costs and has exceeded the DOE cost-reduction goals. 15 refs.« less

Design and implementation of an optical Gaussian noise generator

NASA Astrophysics Data System (ADS)

Za~O, Leonardo; Loss, Gustavo; Coelho, Rosângela

2009-08-01

A design of a fast and accurate optical Gaussian noise generator is proposed and demonstrated. The noise sample generation is based on the Box-Muller algorithm. The functions implementation was performed on a high-speed Altera Stratix EP1S25 field-programmable gate array (FPGA) development kit. It enabled the generation of 150 million 16-bit noise samples per second. The Gaussian noise generator required only 7.4% of the FPGA logic elements, 1.2% of the RAM memory, 0.04% of the ROM memory, and a laser source. The optical pulses were generated by a laser source externally modulated by the data bit samples using the frequency-shift keying technique. The accuracy of the noise samples was evaluated for different sequences size and confidence intervals. The noise sample pattern was validated by the Bhattacharyya distance (Bd) and the autocorrelation function. The results showed that the proposed design of the optical Gaussian noise generator is very promising to evaluate the performance of optical communications channels with very low bit-error-rate values.

Development of 3He LPSDs and read-out system for the SANS spectrometer at CPHS

NASA Astrophysics Data System (ADS)

Huang, T. C.; Gong, H.; Shao, B. B.; Wang, X. W.; Zhang, Y.; Pang, B. B.

2014-01-01

The Compact Pulsed Hadron Source (CPHS) is a 13-MeV proton-linac-driven neutron source under construction in Tsinghua University. Time-of-flight (TOF) small-angle neutron scattering (SANS) spectrometer is one of the first instruments to be built. It is designed to use linear position-sensitive detectors (LPSDs) of 3He gas proportional counters to cover a 1 m×1 m area. Prototypical LPSDs (Φ = 12 mm, L=1 m) have been made and read-out system is developed based on charge division. This work describes the in-house fabrication of the prototypical LPSDs and design of the read-out system including front-end electronics and data acquisition (DAQ) system. Key factors of the front-end electronics are studied and optimized with PSPICE simulation. DAQ system is designed based on VME bus architecture and FPGA Mezzanine Card (FMC) standard with high flexibility and extendibility. Preliminary experiments are carried out and the results are present and discussed.

Measurement-device-independent quantum key distribution with correlated source-light-intensity errors

NASA Astrophysics Data System (ADS)

Jiang, Cong; Yu, Zong-Wen; Wang, Xiang-Bin

2018-04-01

We present an analysis for measurement-device-independent quantum key distribution with correlated source-light-intensity errors. Numerical results show that the results here can greatly improve the key rate especially with large intensity fluctuations and channel attenuation compared with prior results if the intensity fluctuations of different sources are correlated.

Learning design in healthcare education.

PubMed

Ellaway, Rachel; Dalziel, James; Dalziel, Bronwen

2008-01-01

Emerging from ongoing work into educational modelling languages, learning design principles and the IMS Learning Design framework provide formal ways to annotate and record educational activities. Once educational activities have been encoded they can be played, replayed, adopted, shared, and analysed, thereby reifying much that is otherwise lost in face-to-face teaching. The use of learning design tools, including the free and open source LAMS system (www.lamsfoundation.org), allow practitioners to experiment with learning design approaches in their own teaching, both in terms of creating and encoding their own designs and playing, adapting and analysing designs from other teachers either from within or outside a particular field or subject area. This paper reviews the key issues associated with designing for learning in the context of healthcare education, some of the themes and approaches already in development or use, and the implications of this approach on the practice and theory of healthcare education.

Carbon Rod Radiant Source for Blast/Fire Interaction Experiments: Proof of Concept and Design.

DTIC Science & Technology

1980-08-30

Contracting Officer’s Technical Representative was David W. Bensen ISt. KEY IFORCS (C~rnuen orm rwv.,,, took of otarfam d *Oent.-y by block fmtr.) Blast/F...42 13b Irradiance at Target Surface Elliptical Reflectors .. ..... 43 13c Irradiance at Target Surface Parabolic and Elliptical Reflectors...44 14 Flux Distribution at Target Surface for One Rod, Parabolic and Elliptical Reflectors ...................... 15

A Systematic Review and Taxonomy of Published Quality Criteria Related to the Evaluation of User-Facing eHealth Programs.

PubMed

Baumel, Amit; Birnbaum, Michael L; Sucala, Madalina

2017-08-01

The purpose of this review was to identify and classify key criteria concepts related to the evaluation of user-facing eHealth programs. In line with the PRISMA statement methodology, computer searches of relevant databases were conducted for studies published between January 1, 2000 and March 1, 2016 that contained explicit quality criteria related to mHealth and eHealth products. Reference lists of included articles, review articles, and grey literature (e.g., books, websites) were searched for additional sources. A team of nine experts led by the first author was gathered to support the classification of these criteria. Identified criteria were extracted, grouped and organized using an inductive thematic analysis. Eighty-four sources - emanating from 26 different courtiers - were included in this review. The team extracted 454 criteria that were grouped into 11 quality domains, 58 criteria concepts and 134 concepts' sub-groups. Quality domains were: Usability, Visual Design, User Engagement, Content, Behavior Change/Persuasive Design, Influence of Social Presence, Therapeutic Alliance, Classification, Credibility/Accountability, and Privacy/Security. Findings suggest that authors around the globe agree on key criteria concepts when evaluating user-facing eHealth products. The high proportion of new published criteria in the second half of this review time-frame (2008-2016), and more specifically, the high proportion of criteria relating to persuasive design, therapeutic alliance and privacy/security within this time-frame, points to the advancements made in recent years within this field.

Measurement-device-independent quantum key distribution with source state errors and statistical fluctuation

NASA Astrophysics Data System (ADS)

Jiang, Cong; Yu, Zong-Wen; Wang, Xiang-Bin

2017-03-01

We show how to calculate the secure final key rate in the four-intensity decoy-state measurement-device-independent quantum key distribution protocol with both source errors and statistical fluctuations with a certain failure probability. Our results rely only on the range of only a few parameters in the source state. All imperfections in this protocol have been taken into consideration without assuming any specific error patterns of the source.

Enhancing the intrinsic work motivation of community nutrition educators: how supportive supervision and job design foster autonomy.

PubMed

Dickin, Katherine L; Dollahite, Jamie S; Habicht, Jean-Pierre

2011-01-01

Mixed-methods research investigated the work motivation of paraprofessional community nutrition educators (CNEs) delivering a long-running public health nutrition program. In interviews, CNEs (n = 9) emphasized "freedom," supportive supervision, and "making a difference" as key sources of motivation. Community nutrition educator surveys (n = 115) confirmed high levels of autonomy, which was associated with supervisors' delegation and support, CNE decision-making on scheduling and curricula, and job satisfaction. Supervisors (n = 32) rated CNEs' job design as having inherently motivating characteristics comparable to professional jobs. Supervisory strategies can complement job design to create structured, supportive contexts that maintain fidelity, while granting autonomy to paraprofessionals to enhance intrinsic work motivation.

NIR light propagation in a digital head model for traumatic brain injury (TBI)

PubMed Central

Francis, Robert; Khan, Bilal; Alexandrakis, George; Florence, James; MacFarlane, Duncan

2015-01-01

Near infrared spectroscopy (NIRS) is capable of detecting and monitoring acute changes in cerebral blood volume and oxygenation associated with traumatic brain injury (TBI). Wavelength selection, source-detector separation, optode density, and detector sensitivity are key design parameters that determine the imaging depth, chromophore separability, and, ultimately, clinical usefulness of a NIRS instrument. We present simulation results of NIR light propagation in a digital head model as it relates to the ability to detect intracranial hematomas and monitor the peri-hematomal tissue viability. These results inform NIRS instrument design specific to TBI diagnosis and monitoring. PMID:26417498

Compressed Secret Key Agreement:Maximizing Multivariate Mutual Information per Bit

NASA Astrophysics Data System (ADS)

Chan, Chung

2017-10-01

The multiterminal secret key agreement problem by public discussion is formulated with an additional source compression step where, prior to the public discussion phase, users independently compress their private sources to filter out strongly correlated components for generating a common secret key. The objective is to maximize the achievable key rate as a function of the joint entropy of the compressed sources. Since the maximum achievable key rate captures the total amount of information mutual to the compressed sources, an optimal compression scheme essentially maximizes the multivariate mutual information per bit of randomness of the private sources, and can therefore be viewed more generally as a dimension reduction technique. Single-letter lower and upper bounds on the maximum achievable key rate are derived for the general source model, and an explicit polynomial-time computable formula is obtained for the pairwise independent network model. In particular, the converse results and the upper bounds are obtained from those of the related secret key agreement problem with rate-limited discussion. A precise duality is shown for the two-user case with one-way discussion, and such duality is extended to obtain the desired converse results in the multi-user case. In addition to posing new challenges in information processing and dimension reduction, the compressed secret key agreement problem helps shed new light on resolving the difficult problem of secret key agreement with rate-limited discussion, by offering a more structured achieving scheme and some simpler conjectures to prove.

Quantum key distribution with an unknown and untrusted source

NASA Astrophysics Data System (ADS)

Zhao, Yi; Qi, Bing; Lo, Hoi-Kwong

2008-05-01

The security of a standard bidirectional “plug-and-play” quantum key distribution (QKD) system has been an open question for a long time. This is mainly because its source is equivalently controlled by an eavesdropper, which means the source is unknown and untrusted. Qualitative discussion on this subject has been made previously. In this paper, we solve this question directly by presenting the quantitative security analysis on a general class of QKD protocols whose sources are unknown and untrusted. The securities of standard Bennett-Brassard 1984 protocol, weak+vacuum decoy state protocol, and one-decoy state protocol, with unknown and untrusted sources are rigorously proved. We derive rigorous lower bounds to the secure key generation rates of the above three protocols. Our numerical simulation results show that QKD with an untrusted source gives a key generation rate that is close to that with a trusted source.

Multiple-input multiple-output visible light communication system based on disorder dispersion components

NASA Astrophysics Data System (ADS)

Yang, Tao; Zhang, Qi; Hao, Yue; Zhou, Xin-hui; Yi, Ming-dong; Wei, Wei; Huang, Wei; Li, Xing-ao

2017-10-01

A multiple-input multiple-output visible light communication (VLC) system based on disorder dispersion components is presented. Instead of monochromatic sources and large size photodetectors used in the traditional VLC systems, broadband sources with different spectra act as the transmitters and a compact imaging chip sensor accompanied by a disorder dispersion component and a calculating component serve as the receivers in the proposed system. This system has the merits of small size, more channels, simple structure, easy integration, and low cost. Simultaneously, the broadband sources are suitable to act as illumination sources for their white color. A regularized procedure is designed to solve a matrix equation for decoding the signals at the receivers. A proof-of-concept experiment using on-off keying modulation has been done to prove the feasibility of the design. The experimental results show that the signals decoded by the receivers fit well with those generated from the transmitters, but the bit error ratio is increased with the number of the signal channels. The experimental results can be further improved using a high-speed charge-coupled device, decreasing noises, and increasing the distance between the transmitters and the receivers.

Addressing female genital mutilation in Europe: a scoping review of approaches to participation, prevention, protection, and provision of services.

PubMed

Baillot, Helen; Murray, Nina; Connelly, Elaine; Howard, Natasha

2018-02-08

Public and policy attention to female genital mutilation (FGM) in diaspora communities has increased in Europe, but research remains limited and misinformation abounds. As a first step to addressing these issues, this study explored FGM prevention and response interventions in Europe, using a scoping literature review and key informant interviews. A scoping study design was selected, using Arksey and O'Malley's six-stage scoping framework to review identified sources. Key informant interviews were used to inform and add depth to literature findings. Findings were summarised thematically, guided by the Scottish Government's '4Ps' framework for tackling violence against women (i.e. participation, prevention, protection, providing services). Seventy literature sources, of 1095 screened, plus 16 individual and 3 group interview sources were included. Several countries have developed promising interventions supporting FGM resistance and recovery. However, gaps remain including community participation, professional knowledge and linkages, and evaluation of approaches. This scoping review is an initial attempt to describe available primary evidence on European initiatives responding to FGM. Further research is required to determine whether interventions are effective, while policy and practice development must be shaped and driven by the experiences, needs, and views of affected communities.

Getting something out of nothing in the measurement-device-independent quantum key distribution

NASA Astrophysics Data System (ADS)

Tan, Yong-Gang; Cai, Qing-Yu; Yang, Hai-Feng; Hu, Yao-Hua

2015-11-01

Because of the monogamy of entanglement, the measurement-device-independent quantum key distribution is immune to the side-information leaking of the measurement devices. When the correlated measurement outcomes are generated from the dark counts, no entanglement is actually obtained. However, secure key bits can still be proven to be generated from these measurement outcomes. Especially, we will give numerical studies on the contributions of dark counts to the key generation rate in practical decoy state MDI-QKD where a signal source, a weaker decoy source and a vacuum decoy source are used by either legitimate key distributer.

Software to Facilitate Remote Sensing Data Access for Disease Early Warning Systems

PubMed Central

Liu, Yi; Hu, Jiameng; Snell-Feikema, Isaiah; VanBemmel, Michael S.; Lamsal, Aashis; Wimberly, Michael C.

2015-01-01

Satellite remote sensing produces an abundance of environmental data that can be used in the study of human health. To support the development of early warning systems for mosquito-borne diseases, we developed an open-source, client based software application to enable the Epidemiological Applications of Spatial Technologies (EASTWeb). Two major design decisions were full automation of the discovery, retrieval and processing of remote sensing data from multiple sources, and making the system easily modifiable in response to changes in data availability and user needs. Key innovations that helped to achieve these goals were the implementation of a software framework for data downloading and the design of a scheduler that tracks the complex dependencies among multiple data processing tasks and makes the system resilient to external errors. EASTWeb has been successfully applied to support forecasting of West Nile virus outbreaks in the United States and malaria epidemics in the Ethiopian highlands. PMID:26644779

Evaluating process in child and family interventions: aggression prevention as an example.

PubMed

Tolan, Patrick H; Hanish, Laura D; McKay, Mary M; Dickey, Mitchell H

2002-06-01

This article reports on 2 studies designed to develop and validate a set of measures for use in evaluating processes of child and family interventions. In Study 1 responses from 187 families attending an outpatient clinic for child behavior problems were factor analyzed to identify scales, consistent across sources: Alliance (Satisfactory Relationship with Interventionist and Program Satisfaction), Parenting Skill Attainment, Child Cooperation During Session, Child Prosocial Behavior, and Child Aggressive Behavior. Study 2 focused on patterns of scale scores among 78 families taking part in a 22-week preventive intervention designed to affect family relationships, parenting, and child antisocial and prosocial behaviors. The factor structure identified in Study 1 was replicated. Scale construct validity was demonstrated through across-source convergence, sensitivity to intervention change, and ability to discriminate individual differences. Path analysis validated the scales' utility in explaining key aspects of the intervention process. Implications for evaluating processes in family interventions are discussed.

The development of health care data warehouses to support data mining.

PubMed

Lyman, Jason A; Scully, Kenneth; Harrison, James H

2008-03-01

Clinical data warehouses offer tremendous benefits as a foundation for data mining. By serving as a source for comprehensive clinical and demographic information on large patient populations, they streamline knowledge discovery efforts by providing standard and efficient mechanisms to replace time-consuming and expensive original data collection, organization, and processing. Building effective data warehouses requires knowledge of and attention to key issues in database design, data acquisition and processing, and data access and security. In this article, the authors provide an operational and technical definition of data warehouses, present examples of data mining projects enabled by existing data warehouses, and describe key issues and challenges related to warehouse development and implementation.

Establishing Extreme Dynamic Range with JWST: Decoding Smoke Signals in the Glare of a Wolf-Rayet Binary

NASA Astrophysics Data System (ADS)

Lau, Ryan; Hankins, M.; Kasliwal, M.; Sivaramakrishnan, A.; Thatte, D.

2017-11-01

Dust is a key ingredient in the formation of stars and planets. However, the dominant channels of dust production throughout cosmic time are still unclear. With its unprecedented sensitivity and spatial resolution in the mid-IR, the James Webb Space Telescope (JWST) is the ideal platform to address this issue by investigating the dust abundance, composition, and production rates of various dusty sources. In particular, colliding-wind Wolf-Rayet (WR) binaries are efficient dust producers in the local Universe, and likely existed in the earliest galaxies. To study these interesting objects, we propose JWST observations of the archetypal colliding-wind binary WR 140 to study its dust composition, abundance, and formation mechanisms. We will utilize two key JWST observing modes with the medium resolution spectrometer (MRS) on the Mid-Infrared Instrument (MIRI) and the Aperture Masking Interferometry (AMI) mode with the Near Infrared Imager and Slitless Spectrograph (NIRISS). Our proposed observations will yield high impact scientific results on the dust forming properties WR binaries, and establish a benchmark for key observing modes for imaging bright sources with faint extended emission. This will be valuable in various astrophysical contexts including mass-loss from evolved stars, dusty tori around active galactic nuclei, and protoplanetary disks. We are committed to designing and delivering science-enabling products for the JWST community that address technical issues such as bright source artifacts that will limit the maximum achievable image contrast.

Report of the Snowmass M6 Working Group on high intensity proton sources

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weiren Chou and J. Wei

The U.S. high-energy physics program needs an intense proton source, a 1-4 MW Proton Driver (PD), by the end of this decade. This machine will serve as a stand-alone facility that will provide neutrino superbeams and other high intensity secondary beams such as kaons, muons, neutrons, and anti-protons (cf. E1 and E5 group reports) and also serve as the first stage of a neutrino factory (cf. M1 group report). It can also be a high brightness source for a VLHC. Based on present accelerator technology and project construction experience, it is both feasible and cost-effective to construct a 1-4 MWmore » Proton Driver. Two recent PD design studies have been made, one at FNAL and the other at the BNL. Both designed PD's for 1 MW proton beams at a cost of about U.S. $200M (excluding contingency and overhead) and both designs were upgradeable to 4 MW. An international collaboration between FNAL, BNL and KEK on high intensity proton facilities is addressing a number of key design issues. The superconducting (sc) RF cavities, cryogenics, and RF controls developed for the SNS can be directly adopted to save R&D efforts, cost, and schedule. PD studies are also actively being pursued at Europe and Japan.« less

Spallation Neutron Source Second Target Station Integrated Systems Update

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ankner, John Francis; An, Ke; Blokland, Willem

The Spallation Neutron Source (SNS) was designed from the beginning to accommodate both an accelerator upgrade to increase the proton power and a second target station (STS). Four workshops were organized in 2013 and 2014 to identify key science areas and challenges where neutrons will play a vital role [1-4]. Participants concluded that the addition of STS to the existing ORNL neutron sources was needed to complement the strengths of High Flux Isotope Reactor (HFIR) and the SNS first target station (FTS). To address the capability gaps identified in the workshops, a study was undertaken to identify instrument concepts thatmore » could provide the required new science capabilities. The study outlined 22 instrument concepts and presented an initial science case for STS [5]. These instrument concepts formed the basis of a planning suite of instruments whose requirements determined an initial site layout and moderator selection. An STS Technical Design Report (TDR) documented the STS concept based on those choices [6]. Since issue of the TDR, the STS concept has significantly matured as described in this document.« less

Design Considerations for Post-Acute Care mHealth: Patient Perspectives.

PubMed

Sanger, Patrick; Hartzler, Andrea; Lober, William B; Evans, Heather L; Pratt, Wanda

2014-01-01

Many current mobile health applications ("apps") and most previous research have been directed at management of chronic illnesses. However, little is known about patient preferences and design considerations for apps intended to help in a post-acute setting. Our team is developing an mHealth platform to engage patients in wound tracking to identify and manage surgical site infections (SSI) after hospital discharge. Post-discharge SSIs are a major source of morbidity and expense, and occur at a critical care transition when patients are physically and emotionally stressed. Through interviews with surgical patients who experienced SSI, we derived design considerations for such a post-acute care app. Key design qualities include: meeting basic accessibility, usability and security needs; encouraging patient-centeredness; facilitating better, more predictable communication; and supporting personalized management by providers. We illustrate our application of these guiding design considerations and propose a new framework for mHealth design based on illness duration and intensity.

Using Blocked Fractional Factorial Designs to Construct Discrete Choice Experiments for Health Care Studies

PubMed Central

Jaynes, Jessica; Wong, Weng Kee; Xu, Hongquan

2016-01-01

Discrete choice experiments (DCEs) are increasingly used for studying and quantifying subjects preferences in a wide variety of health care applications. They provide a rich source of data to assess real-life decision making processes, which involve trade-offs between desirable characteristics pertaining to health and health care, and identification of key attributes affecting health care. The choice of the design for a DCE is critical because it determines which attributes’ effects and their interactions are identifiable. We apply blocked fractional factorial designs to construct DCEs and address some identification issues by utilizing the known structure of blocked fractional factorial designs. Our design techniques can be applied to several situations including DCEs where attributes have different number of levels. We demonstrate our design methodology using two health care studies to evaluate (1) asthma patients’ preferences for symptom-based outcome measures, and (2) patient preference for breast screening services. PMID:26823156

A study of optical design of power-saving backlight module with external illuminance

NASA Astrophysics Data System (ADS)

Fang, Yi-Chin; Tzeng, Yih-Fong

2014-05-01

In backlight modules, the light guide plate (LGP) is a key component for performance and also facilitates access to develop LGPs on its own. In this research, we propose a newly developed method: LEDs with freeform as a lighting source, are employed to integrate and manipulate the specially designed and optimized 3D-like pattern distribution of the micro features in order to obtain the required optical characteristics at maximal performance. In this research propose the concept of Light Guide Film(LGF) at the back side of Back Light Unit(BLU). This new design may induce the exterior light ,then improve the power-saving of existent BLU. Two design models are reseated: One is design for 14 inch LCD monitor of notebook computer, which might improve 21% compared to traditional one. Another is designed for 3.5 inch LCD for mobile phone display ,which might improve 15% compared to traditional one.

Cross-Matching Source Observations from the Palomar Transient Factory (PTF)

NASA Astrophysics Data System (ADS)

Laher, Russ; Grillmair, C.; Surace, J.; Monkewitz, S.; Jackson, E.

2009-01-01

Over the four-year lifetime of the PTF project, approximately 40 billion instances of astronomical-source observations will be extracted from the image data. The instances will correspond to the same astronomical objects being observed at roughly 25-50 different times, and so a very large catalog containing important object-variability information will be the chief PTF product. Organizing astronomical-source catalogs is conventionally done by dividing the catalog into declination zones and sorting by right ascension within each zone (e.g., the USNOA star catalog), in order to facilitate catalog searches. This method was reincarnated as the "zones" algorithm in a SQL-Server database implementation (Szalay et al., MSR-TR-2004-32), with corrections given by Gray et al. (MSR-TR-2006-52). The primary advantage of this implementation is that all of the work is done entirely on the database server and client/server communication is eliminated. We implemented the methods outlined in Gray et al. for a PostgreSQL database. We programmed the methods as database functions in PL/pgSQL procedural language. The cross-matching is currently based on source positions, but we intend to extend it to use both positions and positional uncertainties to form a chi-square statistic for optimal thresholding. The database design includes three main tables, plus a handful of internal tables. The Sources table stores the SExtractor source extractions taken at various times; the MergedSources table stores statistics about the astronomical objects, which are the result of cross-matching records in the Sources table; and the Merges table, which associates cross-matched primary keys in the Sources table with primary keys in the MergedSoures table. Besides judicious database indexing, we have also internally partitioned the Sources table by declination zone, in order to speed up the population of Sources records and make the database more manageable. The catalog will be accessible to the public after the proprietary period through IRSA (irsa.ipac.caltech.edu).

Application Research of Horn Array Multi-Beam Antenna in Reference Source System for Satellite Interference Location

NASA Astrophysics Data System (ADS)

Zhou, Ping; Lin, Hui; Zhang, Qi

2018-01-01

The reference source system is a key factor to ensure the successful location of the satellite interference source. Currently, the traditional system used a mechanical rotating antenna which leaded to the disadvantages of slow rotation and high failure-rate, which seriously restricted the system’s positioning-timeliness and became its obvious weaknesses. In this paper, a multi-beam antenna scheme based on the horn array was proposed as a reference source for the satellite interference location, which was used as an alternative to the traditional reference source antenna. The new scheme has designed a small circularly polarized horn antenna as an element and proposed a multi-beamforming algorithm based on planar array. Moreover, the simulation analysis of horn antenna pattern, multi-beam forming algorithm and simulated satellite link cross-ambiguity calculation have been carried out respectively. Finally, cross-ambiguity calculation of the traditional reference source system has also been tested. The comparison between the results of computer simulation and the actual test results shows that the scheme is scientific and feasible, obviously superior to the traditional reference source system.

Quantum key distribution with an unknown and untrusted source

NASA Astrophysics Data System (ADS)

Zhao, Yi; Qi, Bing; Lo, Hoi-Kwong

2009-03-01

The security of a standard bi-directional ``plug & play'' quantum key distribution (QKD) system has been an open question for a long time. This is mainly because its source is equivalently controlled by an eavesdropper, which means the source is unknown and untrusted. Qualitative discussion on this subject has been made previously. In this paper, we present the first quantitative security analysis on a general class of QKD protocols whose sources are unknown and untrusted. The securities of standard BB84 protocol, weak+vacuum decoy state protocol, and one-decoy decoy state protocol, with unknown and untrusted sources are rigorously proved. We derive rigorous lower bounds to the secure key generation rates of the above three protocols. Our numerical simulation results show that QKD with an untrusted source gives a key generation rate that is close to that with a trusted source. Our work is published in [1]. [4pt] [1] Y. Zhao, B. Qi, and H.-K. Lo, Phys. Rev. A, 77:052327 (2008).

Longitudinal Gradient Dipole Magnet Prototype for APS at ANL

DOE PAGES

Kashikhin, V. S.; Borland, M.; Chlachidze, G.; ...

2016-01-26

We planned an upgrade of the Advanced Photon Source at Argonne National Laboratory (ANL). The main goal of the upgrade is to improve the storage ring performance based on more advanced optics. One of the key magnet system elements is bending dipole magnets having a field strength change along the electron beam path. Moreover, a prototype of one such longitudinal gradient dipole magnet has been designed, built, and measured in a collaborative effort of ANL and Fermilab. Our paper discusses various magnetic design options, the selected magnet design, and the fabrication technology. The prototype magnet has been measured by rotationalmore » coils, a stretched wire, and a Hall probe. Measurement results are discussed and compared with simulations.« less

Near-term hybrid vehicle program, phase 1. Appendix B: Design trade-off studies report. Volume 2: Supplement to design trade-off studies

NASA Technical Reports Server (NTRS)

1979-01-01

Results of studies leading to the preliminary design of a hybrid passenger vehicle which is projected to have the maximum potential for reducing petroleum consumption in the near term are presented. Heat engine/electric hybrid vehicle tradeoffs, assessment of battery power source, and weight and cost analysis of key components are among the topics covered. Performance of auxiliary equipment, such as power steering, power brakes, air conditioning, lighting and electrical accessories, heating and ventilation is discussed along with the selection of preferred passenger compartment heating procedure for the hybrid vehicle. Waste heat from the engine, thermal energy storage, and an auxiliary burner are among the approaches considered.

Ring-patterned plasmonic photonic crystal thermal light source for miniaturized near-infrared spectrometers

NASA Astrophysics Data System (ADS)

Labib, Shady R.; Elsayed, Ahmed A.; Sabry, Yasser M.; Khalil, Diaa

2018-02-01

There is a growing number of spectroscopy applications in the near-infrared (NIR) range including gas sensing, food analysis, pharmaceutical and industrial applications that requires highly efficient, more compact and low-cost miniaturized spectrometers. One of the key components for such systems is the wideband light source that can be fabricated using Silicon technology and hence integrated with other components on the same chip. In this work, we report a ring-patterned plasmonic photonic crystal (PC) thermal light source for miniaturized near-infrared spectrometers. The design is based on silicon and tuned to achieve wavelength selectivity in the emitted spectrum. The design is optimized by using Rigorous Coupled-Wave Analysis (RCWA) simulation, which is used to compute the power reflectance and transmittance that are used to predict the emissivity of the structure. The design consists of a PC of silicon rings coated with platinum. The period of the structure is about 2 μm and the silicon is highly-doped with n-type doping level in the order of 1019-1020 cm-3 to enhance the free-carrier absorption. The ring etching depth, diameter and shell thickness are optimized to increase its emissivity within a specific wavelength range of interest. The simulation results show an emissivity exceeding 0.9 in the NIR range up to 2.5 μm, while the emissivity is decreased significantly for longer wavelengths suppressing the emission out of the range of interest, and hence increasing the efficiency for the source. The reported results open the door for black body radiation engineering in integrated silicon sources for spectrometer miniaturization.

Market Evolution: Wholesale Electricity Market Design for 21st Century Power Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cochran, Jaquelin; Miller, Mackay; Milligan, Michael

2013-10-01

Demand for affordable, reliable, domestically sourced, and low-carbon electricity is on the rise. This growing demand is driven in part by evolving public policy priorities, especially reducing the health and environmental impacts of electricity service and expanding energy access to under-served customers. Consequently, variable renewable energy resources comprise an increasing share ofelectricity generation globally. At the same time, new opportunities for addressing the variability of renewables are being strengthened through advances in smart grids, communications, and technologies that enable dispatchable demand response and distributed generation to extend to the mass market. A key challenge of merging these opportunities is marketmore » design -- determining how to createincentives and compensate providers justly for attributes and performance that ensure a reliable and secure grid -- in a context that fully realizes the potential of a broad array of sources of flexibility in both the wholesale power and retail markets. This report reviews the suite of wholesale power market designs in use and under consideration to ensure adequacy, security, and flexibilityin a landscape of significant variable renewable energy. It also examines considerations needed to ensure that wholesale market designs are inclusive of emerging technologies, such as demand response, distributed generation, and storage.« less

Powering an in-space 3D printer using solar light energy

NASA Astrophysics Data System (ADS)

Leake, Skye; McGuire, Thomas; Parsons, Michael; Hirsch, Michael P.; Straub, Jeremy

2016-05-01

This paper describes how a solar power source can enable in-space 3D printing without requiring conversion to electric power and back. A design for an in-space 3D printer is presented, with a particular focus on the power generation system. Then, key benefits are presented and evaluated. Specifically, the approach facilitates the design of a spacecraft that can be built, launched, and operated at very low cost levels. The proposed approach also facilitates easy configuration of the amount of energy that is supplied. Finally, it facilitates easier disposal by removing the heavy metals and radioactive materials required for a nuclear-power solution.

Overview of the Solar Dynamic Ground Test Demonstration Program at the NASA Lewis Research Center

NASA Technical Reports Server (NTRS)

Shaltens, Richard K.

1995-01-01

The Solar Dynamic (SD) Ground Test Demonstration (GTD) program demonstrates the availability of SD technologies in a simulated space environment at the NASA Lewis Research Center (LERC) vacuum facility. Data from the SD GTD program will be provided to the joint U.S. and Russian team which is currently designing a 2 kW SD flight demonstration power system. This SD technology has the potential as a future power source for the International Space Station. This paper reviews the goals and status of the SD GTD program. A description of the SD GTD system includes key design features of the system, subsystems and components.

GSE, data management system programmers/User' manual

NASA Technical Reports Server (NTRS)

Schlagheck, R. A.; Dolerhie, B. D., Jr.; Ghiglieri, F. J.

1974-01-01

The GSE data management system is a computerized program which provides for a central storage source for key data associated with the mechanical ground support equipment (MGSE). Eight major sort modes can be requested by the user. Attributes that are printed automatically with each sort include the GSE end item number, description, class code, functional code, fluid media, use location, design responsibility, weight, cost, quantity, dimensions, and applicable documents. Multiple subsorts are available for the class code, functional code, fluid media, use location, design responsibility, and applicable document categories. These sorts and how to use them are described. The program and GSE data bank may be easily updated and expanded.

An evaluation on the design of beam shaping assembly based on the D-T reaction for BNCT

NASA Astrophysics Data System (ADS)

Asnal, M.; Liamsuwan, T.; Onjun, T.

2015-05-01

Boron Neutron Capture Therapy (BNCT) can be achieved by using a compact neutron generator such as a compact D-T neutron source, in which neutron energy must be in the epithermal energy range with sufficient flux. For these requirements, a Beam Shaping Assembly (BSA) is needed. In this paper, three BSA designs based on the D-T reaction for BNCT are discussed. It is found that the BSA configuration designed by Rasouli et al. satisfies all of the International Atomic Energy Agency (IAEA) criteria. It consists of 14 cm uranium as multiplier, 23 cm TiF3 and 36 cm Fluental as moderator, 4 cm Fe as fast neutron filter, 1 mm Li as thermal neutron filter, 2.6 cm Bi as gamma ray filter, and Pb as collimator and reflector. It is also found that use of specific filters is important for removing the fast and thermal neutrons and gamma contamination. Moreover, an appropriate neutron source plays a key role in providing a proper epithermal flux.

Parameter optimization in biased decoy-state quantum key distribution with both source errors and statistical fluctuations

NASA Astrophysics Data System (ADS)

Zhu, Jian-Rong; Li, Jian; Zhang, Chun-Mei; Wang, Qin

2017-10-01

The decoy-state method has been widely used in commercial quantum key distribution (QKD) systems. In view of the practical decoy-state QKD with both source errors and statistical fluctuations, we propose a universal model of full parameter optimization in biased decoy-state QKD with phase-randomized sources. Besides, we adopt this model to carry out simulations of two widely used sources: weak coherent source (WCS) and heralded single-photon source (HSPS). Results show that full parameter optimization can significantly improve not only the secure transmission distance but also the final key generation rate. And when taking source errors and statistical fluctuations into account, the performance of decoy-state QKD using HSPS suffered less than that of decoy-state QKD using WCS.

Development of DEMO-FNS tokamak for fusion and hybrid technologies

NASA Astrophysics Data System (ADS)

Kuteev, B. V.; Azizov, E. A.; Alexeev, P. N.; Ignatiev, V. V.; Subbotin, S. A.; Tsibulskiy, V. F.

2015-07-01

The history of fusion-fission hybrid systems based on a tokamak device as an extremely efficient DT-fusion neutron source has passed through several periods of ample research activity in the world since the very beginning of fusion research in the 1950s. Recently, a new roadmap of the hybrid program has been proposed with the goal to build a pilot hybrid plant (PHP) in Russia by 2030. Development of the DEMO-FNS tokamak for fusion and hybrid technologies, which is planned to be built by 2023, is the key milestone on the path to the PHP. This facility is in the phase of conceptual design aimed at providing feasibility studies for a full set of steady state tokamak technologies at a fusion energy gain factor Q ˜ 1, fusion power of ˜40 MW and opportunities for testing a wide range of hybrid technologies with the emphasis on continuous nuclide processing in molten salts. This paper describes the project motivations, its current status and the key issues of the design.

Commentary: Pediatric eHealth Interventions: Common Challenges During Development, Implementation, and Dissemination

PubMed Central

Steele, Ric G.; Connelly, Mark A.; Palermo, Tonya M.; Ritterband, Lee M.

2014-01-01

Objective To provide an overview of common challenges that pediatric eHealth researchers may encounter when planning, developing, testing, and disseminating eHealth interventions along with proposed solutions for addressing these challenges. Methods The article draws on the existing eHealth literature and the authors’ collective experience in pediatric eHealth research. Results and conclusions The challenges associated with eHealth interventions and their proposed solutions are multifaceted and cut across a number of areas from eHealth program development through dissemination. Collaboration with a range of individuals (e.g., multidisciplinary colleagues, commercial entities, primary stakeholders) is the key to eHealth intervention success. To ensure adequate resources for design, development, and planning for sustainability, a number of public and private sources of funding are available. A study design that addresses ethical concerns and security issues is critical to ensure scientific integrity and intervention dissemination. Table I summarizes key issues to consider during eHealth intervention development, testing, and dissemination. PMID:24816766

Key design elements of a data utility for national biosurveillance: event-driven architecture, caching, and Web service model.

PubMed

Tsui, Fu-Chiang; Espino, Jeremy U; Weng, Yan; Choudary, Arvinder; Su, Hoah-Der; Wagner, Michael M

2005-01-01

The National Retail Data Monitor (NRDM) has monitored over-the-counter (OTC) medication sales in the United States since December 2002. The NRDM collects data from over 18,600 retail stores and processes over 0.6 million sales records per day. This paper describes key architectural features that we have found necessary for a data utility component in a national biosurveillance system. These elements include event-driven architecture to provide analyses of data in near real time, multiple levels of caching to improve query response time, high availability through the use of clustered servers, scalable data storage through the use of storage area networks and a web-service function for interoperation with affiliated systems. The methods and architectural principles are relevant to the design of any production data utility for public health surveillance-systems that collect data from multiple sources in near real time for use by analytic programs and user interfaces that have substantial requirements for time-series data aggregated in multiple dimensions.

Public Key Infrastructure Utilization to Provide an Added Level of Authenticity to Transmitted Data

DTIC Science & Technology

2010-03-01

WIFI Wireless Fidelity – a trademark of the Wi-Fi Alliance that manufacturers may use to brand certified products that belong to a class of...removed by the receiving computer. This security concept is applicable for any WIFI or EVDO wireless transmitted computer because only the end users... hacked and keeping the computer safe from outside sources was still a definite concern. Therefore, a non-Hotmail e-mail account was designed

What New Knowledge Would Help Policymakers Better Balance Investments for Optimal Health Outcomes?

PubMed Central

Kindig, David; Day, Patricia; Fox, Daniel M; Gibson, Mark; Knickman, James; Lomas, Jonathan; Stoddart, Gregory

2003-01-01

Objective Review the limitations in cross-sectoral health outcomes research and suggest a future research agenda. Data Sources, Study Design, Data Collection Literature review and workshop discussion. Principal Findings The research evidence that would aid public and private policy makers in answering the question the title poses is quite limited. Conclusions Much more evidence from diverse disciplines is needed, and key areas are suggested. Criteria for progress by 2010 are proposed. PMID:14727804

Draft Environmental Impact Report/Environmental Impact Statement, Bel Marin Keys Unit 5.

DTIC Science & Technology

1982-09-01

generation render it a major indirect source of emissions. The 1979 Bay Area Air Quality Plan contains actions and policies designed to result in the...Base would render not only the immediate environs unacceptable in terms of housing but large portions of Novato as well. The Noise Element of the...of toxic or other deleterious effects on aquatic biota, wildlife or waterfowl, or which render any of these unfit for human consumption either at

Bridging Scales: A Model-Based Assessment of the Technical Tidal-Stream Energy Resource off Massachusetts, USA

NASA Astrophysics Data System (ADS)

Cowles, G. W.; Hakim, A.; Churchill, J. H.

2016-02-01

Tidal in-stream energy conversion (TISEC) facilities provide a highly predictable and dependable source of energy. Given the economic and social incentives to migrate towards renewable energy sources there has been tremendous interest in the technology. Key challenges to the design process stem from the wide range of problem scales extending from device to array. In the present approach we apply a multi-model approach to bridge the scales of interest and select optimal device geometries to estimate the technical resource for several realistic sites in the coastal waters of Massachusetts, USA. The approach links two computational models. To establish flow conditions at site scales ( 10m), a barotropic setup of the unstructured grid ocean model FVCOM is employed. The model is validated using shipboard and fixed ADCP as well as pressure data. For device scale, the structured multiblock flow solver SUmb is selected. A large ensemble of simulations of 2D cross-flow tidal turbines is used to construct a surrogate design model. The surrogate model is then queried using velocity profiles extracted from the tidal model to determine the optimal geometry for the conditions at each site. After device selection, the annual technical yield of the array is evaluated with FVCOM using a linear momentum actuator disk approach to model the turbines. Results for several key Massachusetts sites including comparison with theoretical approaches will be presented.

Information bias in health research: definition, pitfalls, and adjustment methods

PubMed Central

Althubaiti, Alaa

2016-01-01

As with other fields, medical sciences are subject to different sources of bias. While understanding sources of bias is a key element for drawing valid conclusions, bias in health research continues to be a very sensitive issue that can affect the focus and outcome of investigations. Information bias, otherwise known as misclassification, is one of the most common sources of bias that affects the validity of health research. It originates from the approach that is utilized to obtain or confirm study measurements. This paper seeks to raise awareness of information bias in observational and experimental research study designs as well as to enrich discussions concerning bias problems. Specifying the types of bias can be essential to limit its effects and, the use of adjustment methods might serve to improve clinical evaluation and health care practice. PMID:27217764

Design progress of cryogenic hydrogen system for China Spallation Neutron Source

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, G. P.; Zhang, Y.; Xiao, J.

2014-01-29

China Spallation Neutron Source (CSNS) is a large proton accelerator research facility with 100 kW beam power. Construction started in October 2011 and is expected to last 6.5 years. The cryogenic hydrogen circulation is cooled by a helium refrigerator with cooling capacity of 2200 W at 20 K and provides supercritical hydrogen to neutron moderating system. Important progresses of CSNS cryogenic system were concluded as follows. Firstly, process design of cryogenic system has been completed including helium refrigerator, hydrogen loop, gas distribution, and safety interlock. Secondly, an accumulator prototype was designed to mitigate pressure fluctuation caused by dynamic heat loadmore » from neutron moderation. Performance test of the accumulator has been carried out at room and liquid nitrogen temperature. Results show the accumulator with welding bellows regulates hydrogen pressure well. Parameters of key equipment have been identified. The contract for the helium refrigerator has been signed. Mechanical design of the hydrogen cold box has been completed, and the hydrogen pump, ortho-para hydrogen convertor, helium-hydrogen heat exchanger, hydrogen heater, and cryogenic valves are in procurement. Finally, Hydrogen safety interlock has been finished as well, including the logic of gas distribution, vacuum, hydrogen leakage and ventilation. Generally, design and construction of CSNS cryogenic system is conducted as expected.« less

Finite-key security analysis of quantum key distribution with imperfect light sources

DOE PAGES

Mizutani, Akihiro; Curty, Marcos; Lim, Charles Ci Wen; ...

2015-09-09

In recent years, the gap between theory and practice in quantum key distribution (QKD) has been significantly narrowed, particularly for QKD systems with arbitrarily flawed optical receivers. The status for QKD systems with imperfect light sources is however less satisfactory, in the sense that the resulting secure key rates are often overly dependent on the quality of state preparation. This is especially the case when the channel loss is high. Very recently, to overcome this limitation, Tamaki et al proposed a QKD protocol based on the so-called 'rejected data analysis', and showed that its security in the limit of infinitelymore » long keys is almost independent of any encoding flaw in the qubit space, being this protocol compatible with the decoy state method. Here, as a step towards practical QKD, we show that a similar conclusion is reached in the finite-key regime, even when the intensity of the light source is unstable. More concretely, we derive security bounds for a wide class of realistic light sources and show that the bounds are also efficient in the presence of high channel loss. Our results strongly suggest the feasibility of long distance provably secure communication with imperfect light sources.« less

Numerical Simulation and Mechanical Design for TPS Electron Beam Position Monitors

NASA Astrophysics Data System (ADS)

Hsueh, H. P.; Kuan, C. K.; Ueng, T. S.; Hsiung, G. Y.; Chen, J. R.

2007-01-01

Comprehensive study on the mechanical design and numerical simulation for the high resolution electron beam position monitors are key steps to build the newly proposed 3rd generation synchrotron radiation research facility, Taiwan Photon Source (TPS). With more advanced electromagnetic simulation tool like MAFIA tailored specifically for particle accelerator, the design for the high resolution electron beam position monitors can be tested in such environment before they are experimentally tested. The design goal of our high resolution electron beam position monitors is to get the best resolution through sensitivity and signal optimization. The definitions and differences between resolution and sensitivity of electron beam position monitors will be explained. The design consideration is also explained. Prototype deign has been carried out and the related simulations were also carried out with MAFIA. The results are presented here. Sensitivity as high as 200 in x direction has been achieved in x direction at 500 MHz.

Comparing Parents’ and Children’s Views of Children’s Quality of Life after Heart Transplant

PubMed Central

Green, Angela L.; McSweeney, Jean; Ainley, Kathy; Bryant, Janet

2012-01-01

Purpose The purpose of this focused ethnographic study was to explore the quality of life (QOL) of school-age heart-transplant recipients. Design and Methods Semi-structured interviews were conducted with 11 parent-child dyads. Data were analyzed using content analysis and constant comparison. Results Participants identified key factors impacting the children’s QOL including: participation in normal activities, normalcy, staying healthy, sources of strength and support, and struggles (parents’ perspectives) and doing what kids do, being with family and friends, and being a heart transplant kid (children’s perspectives). Practice Implications Interventions focusing on the key factors identified by participants may impact the QOL of school-age heart-transplant recipients. PMID:19161575

Retail grocery store marketing strategies and obesity: an integrative review.

PubMed

Glanz, Karen; Bader, Michael D M; Iyer, Shally

2012-05-01

In-store food marketing can influence food-purchasing behaviors and warrants increased attention given the dramatic rise in obesity. Descriptive and experimental studies of key marketing components have been conducted by consumer scientists, marketing researchers, and public health experts. This review synthesizes research and publications from industry and academic sources and provides direction for developing and evaluating promising interventions. Literature sources for the review were English-language articles published from 1995 to 2010, identified from multidisciplinary search indexes, backward searches of cited articles, review articles, industry reports, and online sources. Only articles that focused on physical grocery stores and food products were included. Data collection occurred in 2010 and 2011. Articles were classified in the categories of product, price, placement, and promotion and divided into controlled laboratory experiments, observation, and field experiments; 125 primary peer-reviewed articles met the inclusion criteria. Narrative synthesis methods were used. Key findings were synthesized by category of focus and study design. Evidence synthesis was completed in 2011. Findings suggest several strategies for in-store marketing to promote healthful eating by increasing availability, affordability, prominence, and promotion of healthful foods and/or restricting or de-marketing unhealthy foods. Key results of research in controlled laboratory studies should be adapted and tested in real-world in-store settings. Industry methods for assessing consumer behavior, such as electronic sales data and individually linked sales information from loyalty card holders, can help public health researchers increase the scientific rigor of field studies. Copyright © 2012 American Journal of Preventive Medicine. Published by Elsevier Inc. All rights reserved.

Design considerations for highly effective fluorescence excitation and detection optical systems for molecular diagnostics

NASA Astrophysics Data System (ADS)

Kasper, Axel; Van Hille, Herbert; Kuk, Sola

2018-02-01

Modern instruments for molecular diagnostics are continuously optimized for diagnostic accuracy, versatility and throughput. The latest progress in LED technology together with tailored optics solutions allows developing highly efficient photonics engines perfectly adapted to the sample under test. Super-bright chip-on-board LED light sources are a key component for such instruments providing maximum luminous intensities in a multitude of narrow spectral bands. In particular the combination of white LEDs with other narrow band LEDs allows achieving optimum efficiency outperforming traditional Xenon light sources in terms of energy consumption, heat dissipation in the system, and switching time between spectral channels. Maximum sensitivity of the diagnostic system can only be achieved with an optimized optics system for the illumination and imaging of the sample. The illumination beam path must be designed for optimum homogeneity across the field while precisely limiting the angular distribution of the excitation light. This is a necessity for avoiding spill-over to the detection beam path and guaranteeing the efficiency of the spectral filtering. The imaging optics must combine high spatial resolution, high light collection efficiency and optimized suppression of excitation light for good signal-to-noise ratio. In order to achieve minimum cross-talk between individual wells in the sample, the optics design must also consider the generation of stray light and the formation of ghost images. We discuss what parameters and limitations have to be considered in an integrated system design approach covering the full path from the light source to the detector.

Finite-key security analyses on passive decoy-state QKD protocols with different unstable sources.

PubMed

Song, Ting-Ting; Qin, Su-Juan; Wen, Qiao-Yan; Wang, Yu-Kun; Jia, Heng-Yue

2015-10-16

In quantum communication, passive decoy-state QKD protocols can eliminate many side channels, but the protocols without any finite-key analyses are not suitable for in practice. The finite-key securities of passive decoy-state (PDS) QKD protocols with two different unstable sources, type-II parametric down-convention (PDC) and phase randomized weak coherent pulses (WCPs), are analyzed in our paper. According to the PDS QKD protocols, we establish an optimizing programming respectively and obtain the lower bounds of finite-key rates. Under some reasonable values of quantum setup parameters, the lower bounds of finite-key rates are simulated. The simulation results show that at different transmission distances, the affections of different fluctuations on key rates are different. Moreover, the PDS QKD protocol with an unstable PDC source can resist more intensity fluctuations and more statistical fluctuation.

Cohort studies in health sciences librarianship

PubMed Central

Eldredge, Jonathan

2002-01-01

Question: What are the key characteristics of the cohort study design and its varied applications, and how can this research design be utilized in health sciences librarianship? Data Sources: The health, social, behavioral, biological, library, earth, and management sciences literatures were used as sources. Study Selection: All fields except for health sciences librarianship were scanned topically for either well-known or diverse applications of the cohort design. The health sciences library literature available to the author principally for the years 1990 to 2000, supplemented by papers or posters presented at annual meetings of the Medical Library Association. Data Extraction: A narrative review for the health, social, behavioral, biological, earth, and management sciences literatures and a systematic review for health sciences librarianship literature for the years 1990 to 2000, with three exceptions, were conducted. The author conducted principally a manual search of the health sciences librarianship literature for the years 1990 to 2000 as part of this systematic review. Main Results: The cohort design has been applied to answer a wide array of theoretical or practical research questions in the health, social, behavioral, biological, and management sciences. Health sciences librarianship also offers several major applications of the cohort design. Conclusion: The cohort design has great potential for answering research questions in the field of health sciences librarianship, particularly evidence-based librarianship (EBL), although that potential has not been fully explored. PMID:12398244

Analytical template protection performance and maximum key size given a Gaussian-modeled biometric source

NASA Astrophysics Data System (ADS)

Kelkboom, Emile J. C.; Breebaart, Jeroen; Buhan, Ileana; Veldhuis, Raymond N. J.

2010-04-01

Template protection techniques are used within biometric systems in order to protect the stored biometric template against privacy and security threats. A great portion of template protection techniques are based on extracting a key from or binding a key to a biometric sample. The achieved protection depends on the size of the key and its closeness to being random. In the literature it can be observed that there is a large variation on the reported key lengths at similar classification performance of the same template protection system, even when based on the same biometric modality and database. In this work we determine the analytical relationship between the system performance and the theoretical maximum key size given a biometric source modeled by parallel Gaussian channels. We consider the case where the source capacity is evenly distributed across all channels and the channels are independent. We also determine the effect of the parameters such as the source capacity, the number of enrolment and verification samples, and the operating point selection on the maximum key size. We show that a trade-off exists between the privacy protection of the biometric system and its convenience for its users.

Bioreactor design for tendon/ligament engineering.

PubMed

Wang, Tao; Gardiner, Bruce S; Lin, Zhen; Rubenson, Jonas; Kirk, Thomas B; Wang, Allan; Xu, Jiake; Smith, David W; Lloyd, David G; Zheng, Ming H

2013-04-01

Tendon and ligament injury is a worldwide health problem, but the treatment options remain limited. Tendon and ligament engineering might provide an alternative tissue source for the surgical replacement of injured tendon. A bioreactor provides a controllable environment enabling the systematic study of specific biological, biochemical, and biomechanical requirements to design and manufacture engineered tendon/ligament tissue. Furthermore, the tendon/ligament bioreactor system can provide a suitable culture environment, which mimics the dynamics of the in vivo environment for tendon/ligament maturation. For clinical settings, bioreactors also have the advantages of less-contamination risk, high reproducibility of cell propagation by minimizing manual operation, and a consistent end product. In this review, we identify the key components, design preferences, and criteria that are required for the development of an ideal bioreactor for engineering tendons and ligaments.

Bioreactor Design for Tendon/Ligament Engineering

PubMed Central

Wang, Tao; Gardiner, Bruce S.; Lin, Zhen; Rubenson, Jonas; Kirk, Thomas B.; Wang, Allan; Xu, Jiake

2013-01-01

Tendon and ligament injury is a worldwide health problem, but the treatment options remain limited. Tendon and ligament engineering might provide an alternative tissue source for the surgical replacement of injured tendon. A bioreactor provides a controllable environment enabling the systematic study of specific biological, biochemical, and biomechanical requirements to design and manufacture engineered tendon/ligament tissue. Furthermore, the tendon/ligament bioreactor system can provide a suitable culture environment, which mimics the dynamics of the in vivo environment for tendon/ligament maturation. For clinical settings, bioreactors also have the advantages of less-contamination risk, high reproducibility of cell propagation by minimizing manual operation, and a consistent end product. In this review, we identify the key components, design preferences, and criteria that are required for the development of an ideal bioreactor for engineering tendons and ligaments. PMID:23072472

An improved scheme on decoy-state method for measurement-device-independent quantum key distribution.

PubMed

Wang, Dong; Li, Mo; Guo, Guang-Can; Wang, Qin

2015-10-14

Quantum key distribution involving decoy-states is a significant application of quantum information. By using three-intensity decoy-states of single-photon-added coherent sources, we propose a practically realizable scheme on quantum key distribution which approaches very closely the ideal asymptotic case of an infinite number of decoy-states. We make a comparative study between this scheme and two other existing ones, i.e., two-intensity decoy-states with single-photon-added coherent sources, and three-intensity decoy-states with weak coherent sources. Through numerical analysis, we demonstrate the advantages of our scheme in secure transmission distance and the final key generation rate.

Sediment source fingerprinting as an aid to catchment management: A review of the current state of knowledge and a methodological decision-tree for end-users

USGS Publications Warehouse

Collins, A.L; Pulley, S.; Foster, I.D.L; Gellis, Allen; Porto, P.; Horowitz, A.J.

2017-01-01

The growing awareness of the environmental significance of fine-grained sediment fluxes through catchment systems continues to underscore the need for reliable information on the principal sources of this material. Source estimates are difficult to obtain using traditional monitoring techniques, but sediment source fingerprinting or tracing procedures, have emerged as a potentially valuable alternative. Despite the rapidly increasing numbers of studies reporting the use of sediment source fingerprinting, several key challenges and uncertainties continue to hamper consensus among the international scientific community on key components of the existing methodological procedures. Accordingly, this contribution reviews and presents recent developments for several key aspects of fingerprinting, namely: sediment source classification, catchment source and target sediment sampling, tracer selection, grain size issues, tracer conservatism, source apportionment modelling, and assessment of source predictions using artificial mixtures. Finally, a decision-tree representing the current state of knowledge is presented, to guide end-users in applying the fingerprinting approach.

New technology and regional studies in human ecology: A Papua New Guinea example

NASA Technical Reports Server (NTRS)

Morren, George E. B., Jr.

1991-01-01

Two key issues in using technologies such as digital image processing and geographic information systems are a conceptually and methodologically valid research design and the exploitation of varied sources of data. With this realized, the new technologies offer anthropologists the opportunity to test hypotheses about spatial and temporal variations in the features of interest within a regionally coherent mosaic of social groups and landscapes. Current research on the Mountain OK of Papua New Guinea is described with reference to these issues.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Buchanan, J.R.; Keilholtz, G.W.

This report discusses the current status of liquid-metal fast breeder (LMFBR) development and one of the principal safety issues, a hypothetical core-disruptive accident (HCDA). Bibliographic information on worldwide LMFBRs relative to the development of the breeder reactor as a safe source of nuclear power is presented for the period 1960 through 1969. The bibliography consists of 1560 abstracts covering early research and development and operating experiences leading up to the present design practices that are necessary for the licensing of breeder reactors. Key-word, author, and permuted-title indexes are included for completeness.

Reflections on the role of open source in health information system interoperability.

PubMed

Sfakianakis, S; Chronaki, C E; Chiarugi, F; Conforti, F; Katehakis, D G

2007-01-01

This paper reflects on the role of open source in health information system interoperability. Open source is a driving force in computer science research and the development of information systems. It facilitates the sharing of information and ideas, enables evolutionary development and open collaborative testing of code, and broadens the adoption of interoperability standards. In health care, information systems have been developed largely ad hoc following proprietary specifications and customized design. However, the wide deployment of integrated services such as Electronic Health Records (EHRs) over regional health information networks (RHINs) relies on interoperability of the underlying information systems and medical devices. This reflection is built on the experiences of the PICNIC project that developed shared software infrastructure components in open source for RHINs and the OpenECG network that offers open source components to lower the implementation cost of interoperability standards such as SCP-ECG, in electrocardiography. Open source components implementing standards and a community providing feedback from real-world use are key enablers of health care information system interoperability. Investing in open source is investing in interoperability and a vital aspect of a long term strategy towards comprehensive health services and clinical research.

PHARAO space atomic clock: new developments on the laser source

NASA Astrophysics Data System (ADS)

Saccoccio, Muriel; Loesel, Jacques; Coatantiec, Claude; Simon, Eric; Laurent, Philippe; Lemonde, Pierre; Maksimovic, I.; Abgrall, M.

2017-11-01

The PHARAO project purpose is to open the way for a new atomic clock generation in space, where laser cooling techniques and microgravity allow high frequency stability and accuracy. The French space agency, CNES is funding and managing the clock construction. The French SYRTE and LKB laboratories are scientific and technical advisers for the clock requirements and the follow-up of subsystem development in industrial companies. EADS SODERN is developing two main subsystems of the PHARAO clock: the Laser Source and the Cesium Tube where atoms are cooled, launched, selected and detected by laser beams. The Laser Source includes an optical bench and electronic devices to generate the laser beams required. This paper describes PHARAO and the role laser beams play in its principle of operation. Then we present the Laser Source design, the technologies involved, and the status of development. Lastly, we focus of a key equipment to reach the performances expected, which is the Extended Cavity Laser Diode.

Using fear appeals in warning labels to promote responsible gambling among VLT players: the key role of depth of information processing.

PubMed

Munoz, Yaromir; Chebat, Jean-Charles; Suissa, Jacob Amnon

2010-12-01

Video lottery terminals (VLT) are a highly lucrative gambling format, but at the same time they are among the most hazardous. Previous research has shown that threatening warnings may be an appropriate approach for promoting protective behavior. The present study explores the potential benefits of threatening warnings in the fight against compulsive gambling. A 4 × 2 factorial design experiment was used to test our model based on both Elaboration Likelihood Model and Protection Motivation Theory. 258 VLT adult players (58% males, 42% females) with various degrees of problem gambling were exposed to three threat levels (plus a control condition) from two different sources (i.e., either a medical source or a source related to the provider of VLT's). Our results show that both higher threat warnings and the medical source of warnings enhance Depth of Information Processing. It was also found that Depth of Information Processing affects positively attitude change and compliance intentions. The theoretical and managerial implications are discussed.

Modeling of laser transmission contour welding process using FEA and DoE

NASA Astrophysics Data System (ADS)

Acherjee, Bappa; Kuar, Arunanshu S.; Mitra, Souren; Misra, Dipten

2012-07-01

In this research, a systematic investigation on laser transmission contour welding process is carried out using finite element analysis (FEA) and design of experiments (DoE) techniques. First of all, a three-dimensional thermal model is developed to simulate the laser transmission contour welding process with a moving heat source. The commercial finite element code ANSYS® multi-physics is used to obtain the numerical results by implementing a volumetric Gaussian heat source, and combined convection-radiation boundary conditions. Design of experiments together with regression analysis is then employed to plan the experiments and to develop mathematical models based on simulation results. Four key process parameters, namely power, welding speed, beam diameter, and carbon black content in absorbing polymer, are considered as independent variables, while maximum temperature at weld interface, weld width, and weld depths in transparent and absorbing polymers are considered as dependent variables. Sensitivity analysis is performed to determine how different values of an independent variable affect a particular dependent variable.

The design and implementation of hydrographical information management system (HIMS)

NASA Astrophysics Data System (ADS)

Sui, Haigang; Hua, Li; Wang, Qi; Zhang, Anming

2005-10-01

With the development of hydrographical work and information techniques, the large variety of hydrographical information including electronic charts, documents and other materials are widely used, and the traditional management mode and techniques are unsuitable for the development of the Chinese Marine Safety Administration Bureau (CMSAB). How to manage all kinds of hydrographical information has become an important and urgent problem. A lot of advanced techniques including GIS, RS, spatial database management and VR techniques are introduced for solving these problems. Some design principles and key techniques of the HIMS including the mixed mode base on B/S, C/S and stand-alone computer mode, multi-source & multi-scale data organization and management, multi-source data integration and diverse visualization of digital chart, efficient security control strategies are illustrated in detail. Based on the above ideas and strategies, an integrated system named Hydrographical Information Management System (HIMS) was developed. And the HIMS has been applied in the Shanghai Marine Safety Administration Bureau and obtained good evaluation.

Dynamic Initiator Imaging at the Advanced Photon Source: Understanding the early stages of initiator function and subsequent explosive interactions

NASA Astrophysics Data System (ADS)

Sanchez, Nate; Neal, Will; Jensen, Brian; Gibson, John; Martinez, Mike; Jaramillo, Dennis; Iverson, Adam; Carlson, Carl

2017-06-01

Recent advances in diagnostics coupled with synchrotron sources have allowed the in-situ investigation of exploding foil initiators (EFI) during flight. We present the first images of EFIs during flight utilizing x-ray phase contrast imaging at the Advanced Photon Source (APS) located in Argonne National Laboratory. These images have provided the DOE/DoD community with unprecedented images resolving details on the micron scale of the flyer formation, plasma instabilities and in flight characteristics along with the subsequent interaction with high explosives on the nanosecond time scale. Phase contrast imaging has allowed the ability to make dynamic measurements on the length and time scale necessary to resolve initiator function and provide insight to key design parameters. These efforts have also probed the fundamental physics at ``burst'' to better understand what burst means in a physical sense, rather than the traditional understanding of burst as a peak in voltage and increase in resistance. This fundamental understanding has led to increased knowledge on the mechanisms of burst and has allowed us to improve our predictive capability through magnetohydrodnamic modeling. Results will be presented from several EFI designs along with a look to the future for upcoming work.

Design and experimental study of an integrated vapor chamber-thermal energy storage system

NASA Astrophysics Data System (ADS)

Kota, Krishna M.

Future defense, aerospace and automotive technologies involve electronic systems that release high pulsed waste heat like during high power microwave and laser diode applications in tactical and combat aircraft, and electrical and electronic systems in hybrid electric vehicles, which will require the development of an efficient thermal management system. A key design issue is the need for fast charging so as not to overheat the key components. The goal of this work is to study the fabrication and technology implementation feasibility of a novel high energy storage, high heat flux passive heat sink. Key focus is to verify by theory and experiments, the practicability of using phase change materials as a temporary storage of waste heat for heat sink applications. The reason for storing the high heat fluxes temporarily is to be able to reject the heat at the average level when the heat source is off. Accordingly, a concept of a dual latent heat sink intended for moderate to low thermal duty cycle electronic heat sink applications is presented. This heat sink design combines the features of a vapor chamber with rapid thermal energy storage employing graphite foam inside the heat storage facility along with phase change materials and is attractive owing to its passive operation unlike some of the current thermal management techniques for cooling of electronics employing forced air circulation or external heat exchangers. In addition to the concept, end-application dependent criteria to select an optimized design for this dual latent heat sink are presented. A thermal resistance concept based design tool/model has been developed to analyze and optimize the design for experiments. The model showed that it is possible to have a dual latent heat sink design capable of handling 7 MJ of thermal load at a heat flux of 500 W/cm2 (over an area of 100 cm 2) with a volume of 0.072 m3 and weighing about 57.5 kg. It was also found that with such high heat flux absorption capability, the proposed conceptual design could have a vapor-to-condenser temperature difference of less than 10°C with a volume storage density of 97 MJ/m 3 and a mass storage density of 0.122 MJ/kg. The effectiveness of this heat sink depends on the rapidness of the heat storage facility in the design during the pulse heat generation period of the duty cycle. Heat storage in this heat sink involves transient simultaneous laminar film condensation of vapor and melting of an encapsulated phase change material in graphite foam. Therefore, this conjugate heat transfer problem including the wall inertia effect is numerically analyzed and the effectiveness of the heat storage mechanism of the heat sink is verified. An effective heat capacity formulation is employed for modeling the phase change problem and is solved using finite element method. The results of the developed model showed that the concept is effective in preventing undue temperature rise of the heat source. Experiments are performed to investigate the fabrication and implementation feasibility and heat transfer performance for validating the objectives of the design, i.e., to show that the VCTES heat sink is practicable and using PCM helps in arresting the vapor temperature rise in the heat sink. For this purpose, a prototype version of the VCTES heat sink is fabricated and tested for thermal performance. The volume foot-print of the vapor chamber is about 6"X5"X2.5". A custom fabricated thermal energy storage setup is incorporated inside this vapor chamber. A heat flux of 40 W/cm2 is applied at the source as a pulse and convection cooling is used on the condenser surface. Experiments are done with and without using PCM in the thermal energy storage setup. It is found that using PCM as a second latent system in the setup helps in lowering the undue temperature rise of the heat sink system. It is also found that the thermal resistance between the vapor chamber and the thermal energy storage setup, the pool boiling resistance at the heat source in the vapor chamber, the condenser resistance during heat discharging were key parameters that affect the thermal performance. Some suggestions for future improvements in the design to ease its implementation and enhance the heat transfer of this novel heat sink are also presented.

Finite-key security analyses on passive decoy-state QKD protocols with different unstable sources

PubMed Central

Song, Ting-Ting; Qin, Su-Juan; Wen, Qiao-Yan; Wang, Yu-Kun; Jia, Heng-Yue

2015-01-01

In quantum communication, passive decoy-state QKD protocols can eliminate many side channels, but the protocols without any finite-key analyses are not suitable for in practice. The finite-key securities of passive decoy-state (PDS) QKD protocols with two different unstable sources, type-II parametric down-convention (PDC) and phase randomized weak coherent pulses (WCPs), are analyzed in our paper. According to the PDS QKD protocols, we establish an optimizing programming respectively and obtain the lower bounds of finite-key rates. Under some reasonable values of quantum setup parameters, the lower bounds of finite-key rates are simulated. The simulation results show that at different transmission distances, the affections of different fluctuations on key rates are different. Moreover, the PDS QKD protocol with an unstable PDC source can resist more intensity fluctuations and more statistical fluctuation. PMID:26471947

Improved illumination system of laparoscopes using an aspherical lens array.

PubMed

Wu, Rengmao; Qin, Yi; Hua, Hong

2016-06-01

The current fiber-based illumination systems of laparoscopes are unable to uniformly illuminate a large enough area in abdomen due to the limited numerical aperture (NA) of the fiber bundle. Most energy is concentrated in a small region at the center of the illumination area. This limitation becomes problematic in laparoscopes which require capturing a wide field of view. In this paper, we propose an aspherical lens array which is used to direct the outgoing rays from the fiber bundle of laparoscope to produce a more uniformly illuminated, substantially larger field coverage than standalone fiber source. An intensity feedback method is developed to design the aspherical lens unit for extended non-Lambertian sources, which is the key to the design of this lens array. By this method, the lens unit is obtained after only one iteration, and the lens array is constructed by Boolean operation. Then, the ray-tracing technique is used to verify the design. Further, the lens array is fabricated and experimental tests are performed. The results clearly show that the well-illuminated area is increased to about 0.107m(2) from 0.02m(2) (about 5x larger than a standard fiber illumination source). More details of the internal organs can be clearly observed under this improved illumination condition, which also reflects the significant improvement in the optical performance of the laparoscope.

Related Studies in Long Term Lithium Battery Stability

NASA Technical Reports Server (NTRS)

Horning, R. J.; Chua, D. L.

1984-01-01

The continuing growth of the use of lithium electrochemical systems in a wide variety of both military and industrial applications is primarily a result of the significant benefits associated with the technology such as high energy density, wide temperature operation and long term stability. The stability or long term storage capability of a battery is a function of several factors, each important to the overall storage life and, therefore, each potentially a problem area if not addressed during the design, development and evaluation phases of the product cycle. Design (e.g., reserve vs active), inherent material thermal stability, material compatibility and self-discharge characteristics are examples of factors key to the storability of a power source.

Design and Tests of the Hard X-Ray Polarimeter X-Calibur

NASA Technical Reports Server (NTRS)

Beilicke, M.; Baring, M. G.; Barthelmy, S.; Binns, W. R.; Buckley, J.; Cowsik, R.; Dowkontt, P.; Garson, A.; Guo, Q.; Haba, Y.;

Designing social marketing strategies to increase African Americans' access to health promotion programs.

PubMed

Icard, Larry D; Bourjolly, Joretha N; Siddiqui, Nushina

2003-08-01

This qualitative study explored four key factors--source, message, channel, and target--for linking at-risk African Americans with health promotion programs. Among the findings from focus group discussions was that the use of the African American church to involve at-risk African Americans in health promotion programs may actually function as a barrier for some individuals. The study also suggests that use of a high profile person to deliver a message may be counterproductive to efforts to motivate people to use health promotion programs. The significance of these and other findings for designing more effective social marketing strategies to increase at-risk African Americans' access to health promotion programs are discussed.

Energy Systems Integration Facility (ESIF): Golden, CO - Energy Integration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sheppy, Michael; VanGeet, Otto; Pless, Shanti

2015-03-01

At NREL's Energy Systems Integration Facility (ESIF) in Golden, Colo., scientists and engineers work to overcome challenges related to how the nation generates, delivers and uses energy by modernizing the interplay between energy sources, infrastructure, and data. Test facilities include a megawatt-scale ac electric grid, photovoltaic simulators and a load bank. Additionally, a high performance computing data center (HPCDC) is dedicated to advancing renewable energy and energy efficient technologies. A key design strategy is to use waste heat from the HPCDC to heat parts of the building. The ESIF boasts an annual EUI of 168.3 kBtu/ft2. This article describes themore » building's procurement, design and first year of performance.« less

A universal procedure for evaluation and application of surge-protective devices

NASA Technical Reports Server (NTRS)

1980-01-01

The source, nature, and frequency of occurrence of transients must be identified and a representative standard test wave chosen for proof testing. The performance of candidate suppressor devices then can be evaluated against the withstand goals set for the equipment. The various suppressors divide into two classes of generic behavior. The key to a universal procedure for evaluating both classes lies in representing transients as quasi-current sources of defined current impulse duration. The available surge current is established by the Thevenin equivalent transient voltage and source impedance. A load line drawn on the V-I characteristic graph of the suppressor quickly determines the clamping voltage and peak current. These values then can be compared to the requirement. The deposited energy and average power dissipation for multiple transients also can be calculated. The method is illustrated with a design example for motor vehicle alternator load dump suppression.

Searching for X-ray Pulsations from Neutron Stars Using NICER

NASA Astrophysics Data System (ADS)

Ray, Paul S.; Arzoumanian, Zaven; Bogdanov, Slavko; Bult, Peter; Chakrabarty, Deepto; Guillot, Sebastien; Kust Harding, Alice; Ho, Wynn C. G.; Lamb, Frederick K.; Mahmoodifar, Simin; Miller, M. Coleman; Strohmayer, Tod E.; Wilson-Hodge, Colleen A.; Wolff, Michael Thomas

2017-08-01

The Neutron Star Interior Composition Explorer (NICER) presents an exciting new capability for discovering new modulation properties of X-ray emitting neutron stars, including large area, low background, extremely precise absolute time stamps, superb low-energy response and flexible scheduling. The Pulsation Searches and Multiwavelength Coordination working group has designed a 2.5 Ms observing program to search for pulsations and characterize the modulation properties of about 30 known or suspected neutron star sources across a number of source categories. A key early goal will be to search for pulsations from millisecond pulsars that might exhibit thermal pulsations from the surface suitable for pulse profile modeling to constrain the neutron star equation of state. In addition, we will search for pulsations from transitional millisecond pulsars, isolated neutron stars, LMXBs, accretion-powered millisecond pulsars, central compact objects and other sources. We will present our science plan and initial results from the first months of the NICER mission.

Searching for X-ray Pulsations from Neutron Stars Using NICER

NASA Astrophysics Data System (ADS)

Ray, Paul S.; Arzoumanian, Zaven; Gendreau, Keith C.; Bogdanov, Slavko; Bult, Peter; Chakrabarty, Deepto; Chakrabarty, Deepto; Guillot, Sebastien; Harding, Alice; Ho, Wynn C. G.; Lamb, Frederick; Mahmoodifar, Simin; Miller, Cole; Strohmayer, Tod; Wilson-Hodge, Colleen; Wolff, Michael T.; NICER Science Team Working Group on Pulsation Searches and Multiwavelength Coordination

2018-01-01

The Neutron Star Interior Composition Explorer (NICER) presents an exciting new capability for discovering new modulation properties of X-ray emitting neutron stars, including large area, low background, extremely precise absolute time stamps, superb low-energy response and flexible scheduling. The Pulsation Searches and Multiwavelength Coordination working group has designed a 2.5 Ms observing program to search for pulsations and characterize the modulation properties of about 30 known or suspected neutron star sources across a number of source categories. A key early goal will be to search for pulsations from millisecond pulsars that might exhibit thermal pulsations from the surface suitable for pulse profile modeling to constrain the neutron star equation of state. In addition, we will search for pulsations from transitional millisecond pulsars, isolated neutron stars, LMXBs, accretion-powered millisecond pulsars, central compact objects and other sources. We present our science plan and initial results from the first months of the NICER mission.

Heralded quantum repeater based on the scattering of photons off single emitters using parametric down-conversion source.

PubMed

Song, Guo-Zhu; Wu, Fang-Zhou; Zhang, Mei; Yang, Guo-Jian

2016-06-28

Quantum repeater is the key element in quantum communication and quantum information processing. Here, we investigate the possibility of achieving a heralded quantum repeater based on the scattering of photons off single emitters in one-dimensional waveguides. We design the compact quantum circuits for nonlocal entanglement generation, entanglement swapping, and entanglement purification, and discuss the feasibility of our protocols with current experimental technology. In our scheme, we use a parametric down-conversion source instead of ideal single-photon sources to realize the heralded quantum repeater. Moreover, our protocols can turn faulty events into the detection of photon polarization, and the fidelity can reach 100% in principle. Our scheme is attractive and scalable, since it can be realized with artificial solid-state quantum systems. With developed experimental technique on controlling emitter-waveguide systems, the repeater may be very useful in long-distance quantum communication.

Heralded quantum repeater based on the scattering of photons off single emitters using parametric down-conversion source

PubMed Central

Song, Guo-Zhu; Wu, Fang-Zhou; Zhang, Mei; Yang, Guo-Jian

2016-01-01

Quantum repeater is the key element in quantum communication and quantum information processing. Here, we investigate the possibility of achieving a heralded quantum repeater based on the scattering of photons off single emitters in one-dimensional waveguides. We design the compact quantum circuits for nonlocal entanglement generation, entanglement swapping, and entanglement purification, and discuss the feasibility of our protocols with current experimental technology. In our scheme, we use a parametric down-conversion source instead of ideal single-photon sources to realize the heralded quantum repeater. Moreover, our protocols can turn faulty events into the detection of photon polarization, and the fidelity can reach 100% in principle. Our scheme is attractive and scalable, since it can be realized with artificial solid-state quantum systems. With developed experimental technique on controlling emitter-waveguide systems, the repeater may be very useful in long-distance quantum communication. PMID:27350159

A comprehensive experimental characterization of the iPIX gamma imager

NASA Astrophysics Data System (ADS)

Amgarou, K.; Paradiso, V.; Patoz, A.; Bonnet, F.; Handley, J.; Couturier, P.; Becker, F.; Menaa, N.

2016-08-01

The results of more than 280 different experiments aimed at exploring the main features and performances of a newly developed gamma imager, called iPIX, are summarized in this paper. iPIX is designed to quickly localize radioactive sources while estimating the ambient dose equivalent rate at the measurement point. It integrates a 1 mm thick CdTe detector directly bump-bonded to a Timepix chip, a tungsten coded-aperture mask, and a mini RGB camera. It also represents a major technological breakthrough in terms of lightness, compactness, usability, response sensitivity, and angular resolution. As an example of its key strengths, an 241Am source with a dose rate of only few nSv/h can be localized in less than one minute.

Market development directory for solar industrial process heat systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

The purpose of this directory is to provide a basis for market development activities through a location listing of key trade associations, trade periodicals, and key firms for three target groups. Potential industrial users and potential IPH system designers were identified as the prime targets for market development activities. The bulk of the directory is a listing of these two groups. The third group, solar IPH equipment manufacturers, was included to provide an information source for potential industrial users and potential IPH system designers. Trade associates and their publications are listed for selected four-digit Standard Industrial Code (SIC) industries. Sincemore » industries requiring relatively lower temperature process heat probably will comprise most of the near-term market for solar IPH systems, the 80 SIC's included in this chapter have process temperature requirements less than 350/sup 0/F. Some key statistics and a location list of the largest plants (according to number of employees) in each state are included for 15 of the 80 SIC's. Architectural/engineering and consulting firms are listed which are known to have solar experience. Professional associated and periodicals to which information on solar IPH sytstems may be directed also are included. Solar equipment manufacturers and their associations are listed. The listing is based on the SERI Solar Energy Information Data Base (SEIDB).« less

Development of Performance Dashboards in Healthcare Sector: Key Practical Issues.

PubMed

Ghazisaeidi, Marjan; Safdari, Reza; Torabi, Mashallah; Mirzaee, Mahboobeh; Farzi, Jebraeil; Goodini, Azadeh

2015-10-01

Static nature of performance reporting systems in health care sector has resulted in inconsistent, incomparable, time consuming, and static performance reports that are not able to transparently reflect a round picture of performance and effectively support healthcare managers' decision makings. So, the healthcare sector needs interactive performance management tools such as performance dashboards to measure, monitor, and manage performance more effectively. The aim of this article was to identify key issues that need to be addressed for developing high-quality performance dashboards in healthcare sector. A literature review was established to search electronic research databases, e-journals collections, and printed journals, books, dissertations, and theses for relevant articles. The search strategy interchangeably used the terms of "dashboard", "performance measurement system", and "executive information system" with the term of "design" combined with operator "AND". Search results (n=250) were adjusted for duplications, screened based on their abstract relevancy and full-text availability (n=147) and then assessed for eligibility (n=40). Eligible articles were included if they had explicitly focused on dashboards, performance measurement systems or executive information systems design. Finally, 28 relevant articles included in the study. Creating high-quality performance dashboards requires addressing both performance measurement and executive information systems design issues. Covering these two fields, identified contents were categorized to four main domains: KPIs development, Data Sources and data generation, Integration of dashboards to source systems, and Information presentation issues. This study implies the main steps to develop dashboards for the purpose of performance management. Performance dashboards developed on performance measurement and executive information systems principles and supported by proper back-end infrastructure will result in creation of dynamic reports that help healthcare managers to consistently measure the performance, continuously detect outliers, deeply analyze causes of poor performance, and effectively plan for the future.

Conceptual design for a lunar-base CELSS

NASA Technical Reports Server (NTRS)

Schwartzkopf, Steven H.; Cullingford, Hatice S.

1990-01-01

Future human exploration is key to the United States National Space Policy goal of maintaining a world leadership position in space. In the past, spacecraft life support systems have used open-loop technologies that were simple and sufficiently reliable to demonstrate the feasibility of spaceflight. A critical technology area needing development in support of both long duration missions and the establishment of lunar or planetary bases is regenerative life support. The information presented in this paper describes a conceptual design of a Lunar Base Controlled Ecological Life Support System (LCELSS) which supports a crew size ranging from 4 to 100. The system includes, or incorporates interfaces with, eight primary subsystems. An initial description of the Lunar-Base CELSS subsystems is provided within the framework of the conceptual design. The system design includes both plant (algae and higher plant) and animal species as potential food sources.

High Level Analysis, Design and Validation of Distributed Mobile Systems with CoreASM

NASA Astrophysics Data System (ADS)

Farahbod, R.; Glässer, U.; Jackson, P. J.; Vajihollahi, M.

System design is a creative activity calling for abstract models that facilitate reasoning about the key system attributes (desired requirements and resulting properties) so as to ensure these attributes are properly established prior to actually building a system. We explore here the practical side of using the abstract state machine (ASM) formalism in combination with the CoreASM open source tool environment for high-level design and experimental validation of complex distributed systems. Emphasizing the early phases of the design process, a guiding principle is to support freedom of experimentation by minimizing the need for encoding. CoreASM has been developed and tested building on a broad scope of applications, spanning computational criminology, maritime surveillance and situation analysis. We critically reexamine here the CoreASM project in light of three different application scenarios.

Radioistopes to Solar to High Energy Accelerators - Chip-Scale Energy Sources

NASA Astrophysics Data System (ADS)

Lal, Amit

2013-12-01

This talk will present MEMS based power sources that utilize radioisotopes, solar energy, and potentially nuclear energy through advancements in integration of new structures and materials within MEMS. Micro power harvesters can harness power from vibration, radioisotopes, light, sound, and biology may provide pathways to minimize or even eliminate batteries in sensor nodes. In this talk work on radioisotope thin films for MEMS will be include the self-reciprocating cantilever, betavoltaic cells, and high DC voltages. The self-reciprocating cantilever energy harvester allows small commercially viable amounts of radioisotopes to generate mW to Watts of power so that very reliable power sources that last 100s of years are possible. The tradeoffs between reliability and potential stigma with radioisotopes allow one to span a useful design space with reliability as a key parameter. These power sources provide pulsed power at three different time scales using mechanical, RF, and static extraction of energy from collected charge. Multi-use capability, both harvesting radioisotope power and local vibration energy extends the reliability of micro-power sources further.

[Regulation framework of watershed landscape pattern for non-point source pollution control based on 'source-sink' theory: A case study in the watershed of Maluan Bay, Xiamen City, China].

PubMed

Huang, Ning; Wang, Hong Ying; Lin, Tao; Liu, Qi Ming; Huang, Yun Feng; Li, Jian Xiong

2016-10-01

Watershed landscape pattern regulation and optimization based on 'source-sink' theory for non-point source pollution control is a cost-effective measure and still in the exploratory stage. Taking whole watershed as the research object, on the basis of landscape ecology, related theories and existing research results, a regulation framework of watershed landscape pattern for non-point source pollution control was developed at two levels based on 'source-sink' theory in this study: 1) at watershed level: reasonable basic combination and spatial pattern of 'source-sink' landscape was analyzed, and then holistic regulation and optimization method of landscape pattern was constructed; 2) at landscape patch level: key 'source' landscape was taken as the focus of regulation and optimization. Firstly, four identification criteria of key 'source' landscape including landscape pollutant loading per unit area, landscape slope, long and narrow transfer 'source' landscape, pollutant loading per unit length of 'source' landscape along the riverbank were developed. Secondly, nine types of regulation and optimization methods for different key 'source' landscape in rural and urban areas were established, according to three regulation and optimization rules including 'sink' landscape inlay, banding 'sink' landscape supplement, pollutants capacity of original 'sink' landscape enhancement. Finally, the regulation framework was applied for the watershed of Maluan Bay in Xiamen City. Holistic regulation and optimization mode of watershed landscape pattern of Maluan Bay and key 'source' landscape regulation and optimization measures for the three zones were made, based on GIS technology, remote sensing images and DEM model.

International Space Station Major Constituent Analyzer On-Orbit Performance

NASA Technical Reports Server (NTRS)

Gardner, Ben D.; Erwin, Phillip M.; Thoresen, Souzan; Granahan, John; Matty, Chris

2012-01-01

The Major Constituent Analyzer is a mass spectrometer based system that measures the major atmospheric constituents on the International Space Station. A number of limited-life components require periodic changeout, including the ORU 02 analyzer and the ORU 08 Verification Gas Assembly. Over the past two years, two ORU 02 analyzer assemblies have operated nominally while two others have experienced premature on-orbit failures. These failures as well as nominal performances demonstrate that ORU 02 performance remains a key determinant of MCA performance and logistical support. It can be shown that monitoring several key parameters can maximize the capacity to monitor ORU health and properly anticipate end of life. Improvements to ion pump operation and ion source tuning are expected to improve lifetime performance of the current ORU 02 design.

Sound reduction of air compressors using a systematic approach

NASA Astrophysics Data System (ADS)

Moylan, Justin Tharp

The noise emitted by portable electric air compressors can often be a nuisance or potentially hazardous to the operator or others nearby. Therefore, reducing the noise of these air compressors is desired. This research focuses on compressors with a reciprocating piston design as this is the most common type of pump design for portable compressors. An experimental setup was developed to measure the sound and vibration of the air compressors, including testing inside a semi-anechoic chamber. The design of a quiet air compressor was performed in four stages: 1) Teardown and benchmarking of air compressors, 2) Identification and isolation of noise sources, 3) Development of individual means to quiet noise sources, 4) Selection and testing of integrated solutions. The systematic approach and results for each of these stages will be discussed. Two redesigned solutions were developed and measured to be approximately 65% quieter than the previous unmodified compressor. An additional analysis was performed on the solutions selected by the participants involved in the selection process. This analysis involved determining which of the design criteria each participant considered most important when selecting solutions. The results from each participant were then compared to their educational background and experience and correlations were identified. The correlations discovered suggest that educational background and experience may be key determinants for the preference models developed.

Ground Source Heat Pump Sub-Slab Heat Exchange Loop Performance in a Cold Climate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mittereder, N.; Poerschke, A.

2013-11-01

This report presents a cold-climate project that examines an alternative approach to ground source heat pump (GSHP) ground loop design. The innovative ground loop design is an attempt to reduce the installed cost of the ground loop heat exchange portion of the system by containing the entire ground loop within the excavated location beneath the basement slab. Prior to the installation and operation of the sub-slab heat exchanger, energy modeling using TRNSYS software and concurrent design efforts were performed to determine the size and orientation of the system. One key parameter in the design is the installation of the GSHPmore » in a low-load home, which considerably reduces the needed capacity of the ground loop heat exchanger. This report analyzes data from two cooling seasons and one heating season. Upon completion of the monitoring phase, measurements revealed that the initial TRNSYS simulated horizontal sub-slab ground loop heat exchanger fluid temperatures and heat transfer rates differed from the measured values. To determine the cause of this discrepancy, an updated model was developed utilizing a new TRNSYS subroutine for simulating sub-slab heat exchangers. Measurements of fluid temperature, soil temperature, and heat transfer were used to validate the updated model.« less

An improved scheme on decoy-state method for measurement-device-independent quantum key distribution

PubMed Central

Wang, Dong; Li, Mo; Guo, Guang-Can; Wang, Qin

2015-01-01

Quantum key distribution involving decoy-states is a significant application of quantum information. By using three-intensity decoy-states of single-photon-added coherent sources, we propose a practically realizable scheme on quantum key distribution which approaches very closely the ideal asymptotic case of an infinite number of decoy-states. We make a comparative study between this scheme and two other existing ones, i.e., two-intensity decoy-states with single-photon-added coherent sources, and three-intensity decoy-states with weak coherent sources. Through numerical analysis, we demonstrate the advantages of our scheme in secure transmission distance and the final key generation rate. PMID:26463580

Enhancing Linkages Between Healthy Diets, Local Agriculture, and Sustainable Food Systems: The School Meals Planner Package in Ghana.

PubMed

Fernandes, Meenakshi; Galloway, Rae; Gelli, Aulo; Mumuni, Daniel; Hamdani, Salha; Kiamba, Josephine; Quarshie, Kate; Bhatia, Rita; Aurino, Elisabetta; Peel, Francis; Drake, Lesley

2016-12-01

Interventions that enhance linkages between healthy diets and local agriculture can promote sustainable food systems. Home-grown school feeding programs present a promising entry point for such interventions, through the delivery of nutritious menus and meals. To describe the adaptation of the School Meals Planner Package to the programmatic and environmental reality in Ghana during the 2014 to 2015 school year. Guided by a conceptual framework highlighting key considerations and trade-offs in menu design, an open-source software was developed that could be easily understood by program implementers. Readily available containers from markets were calibrated into "handy measures" to support the provision of adequate quantities of food indicated by menus. Schools and communities were sensitized to the benefits of locally sourced, nutrient-rich diets. A behavior change communication campaign including posters and songs promoting healthy diets was designed and disseminated in schools and communities. The School Meals Planner Package was introduced in 42 districts in Ghana, reaching more than 320 000 children. Monitoring reports and feedback on its use were positive, demonstrating how the tool can be used by planners and implementers alike to deliver nutritious, locally-sourced meals to schoolchildren. The value of the tool has been recognized at the highest levels by Ghana's government who have adopted it as official policy. The School Meals Planner Package supported the design of nutritious, locally sourced menus for the school feeding program in Ghana. The tool can be similarly adapted for other countries to meet context-specific needs. © The Author(s) 2016.

Toward Mentoring in Palliative Social Work: A Narrative Review of Mentoring Programs in Social Work.

PubMed

Toh, Ying Pin; Karthik, R; Teo, Chia Chia; Suppiah, Sarasvathy; Cheung, Siew Li; Krishna, Lalit

2018-03-01

Mentoring by an experienced practitioner enhances professional well-being, promotes resilience, and provides a means of addressing poor job satisfaction and high burnout rates among medical social workers. This is a crucial source of support for social workers working in fields with high risk of compassion fatigue and burnout like palliative care. Implementing such a program, however, is hindered by differences in understanding and application of mentoring practice. This narrative review of mentoring practice in social work seeks to identify key elements and common approaches within successful mentoring programs in social work that could be adapted to guide the design of new mentoring programs in medical social work. Methodology and Data Sources: A literature search of mentoring programs in social work between January 1, 2000, and December 31, 2015, using Pubmed, CINAHL, OVID, ERIC, Scopus, Cochrane and ScienceDirect databases, involving a senior experienced mentor and undergraduate and/or junior postgraduates, was carried out. A total of 1302 abstracts were retrieved, 22 full-text articles were analyzed, and 8 articles were included. Thematic analysis of the included articles revealed 7 themes pertaining to the mentoring process, outcomes and barriers, and the characteristics of mentoring relationships, mentors, mentees, and host organizations. Common themes in prevailing mentoring practices help identify key elements for the design of an effective mentoring program in medical social work. We conclude with a discussion of the implications of these findings upon clinical practice in palliative care and on sustaining such a program.

Nuclear Power System Architecture and Safety Study- Feasibility of Launch Pad Explosion Simulation using Radios

NASA Astrophysics Data System (ADS)

Destefanis, Stefano; Tracino, Emanuele; Giraudo, Martina

2014-06-01

During a mission involving a spacecraft using nuclear power sources (NPS), the consequences to the population induced by an accident has to be taken into account carefully.Part of the study (led by AREVA, with TAS-I as one of the involved parties) was devoted to "Worst Case Scenario Consolidation". In particular, one of the activities carried out by TAS-I had the aim of characterizing the accidental environment (explosion on launch pad or during launch) and consolidate the requirements given as input in the study. The resulting requirements became inputs for Nuclear Power Source container design.To do so, TAS-I did first an overview of the available technical literature (mostly developed in the frame of NASA Mercury / Apollo program), to identify the key parameters to be used for analytical assessment (blast pressure wave, fragments size, speed and distribution, TNT equivalent of liquid propellant).Then, a simplified Radioss model was setup, to verify both the cards needed for blast / fragment impact analysis and the consistency between preliminary results and available technical literature (Radioss is commonly used to design mine - resistant vehicles, by simulating the effect of blasts onto structural elements, and it is used in TAS-I for several types of analysis, including land impact, water impact and fluid - structure interaction).The obtained results (albeit produced by a very simplified model) are encouraging, showing that the analytical tool and the selected key parameters represent a step in the right direction.

Key Considerations of Community, Scalability, Supportability, Security, and Functionality in Selecting Open-Source Software in California Universities as Perceived by Technology Leaders

ERIC Educational Resources Information Center

Britton, Todd Alan

2014-01-01

Purpose: The purpose of this study was to examine the key considerations of community, scalability, supportability, security, and functionality for selecting open-source software in California universities as perceived by technology leaders. Methods: After a review of the cogent literature, the key conceptual framework categories were identified…

Energy harvesting concepts for small electric unmanned systems

NASA Astrophysics Data System (ADS)

Qidwai, Muhammad A.; Thomas, James P.; Kellogg, James C.; Baucom, Jared N.

2004-07-01

In this study, we identify and survey energy harvesting technologies for small electrically powered unmanned systems designed for long-term (>1 day) time-on-station missions. An environmental energy harvesting scheme will provide long-term, energy additions to the on-board energy source. We have identified four technologies that cover a broad array of available energy sources: solar, kinetic (wind) flow, autophagous structure-power (both combustible and metal air-battery systems) and electromagnetic (EM) energy scavenging. We present existing conceptual designs, critical system components, performance, constraints and state-of-readiness for each technology. We have concluded that the solar and autophagous technologies are relatively matured for small-scale applications and are capable of moderate power output levels (>1 W). We have identified key components and possible multifunctionalities in each technology. The kinetic flow and EM energy scavenging technologies will require more in-depth study before they can be considered for implementation. We have also realized that all of the harvesting systems require design and integration of various electrical, mechanical and chemical components, which will require modeling and optimization using hybrid mechatronics-circuit simulation tools. This study provides a starting point for detailed investigation into the proposed technologies for unmanned system applications under current development.

Integrated arc suppression unit for defect reduction in PVD applications

NASA Astrophysics Data System (ADS)

Li, Jason; Narasimhan, Murali K.; Pavate, Vikram; Loo, David; Rosenblum, Steve; Trubell, Larry; Scholl, Richard; Seamons, Scott; Hagerty, Chris; Ramaswami, Sesh

1997-09-01

Arcing between the target and plasma during PVD deposition causes substantial damage to the target and splats and other contamination on the deposited films. Arc-related damages and defects are frequently encountered in microelectronics manufacturing and contributes largely to reduced wafer yields. Arcing is caused largely by the charge buildup at the contaminated sites on the target surface that contains either nonconducting inclusions or nodules. Arc suppression is a key issue for defect reduction, yield improvement and for reliable high quality metallization. An Integrated Arc Suppression Unit (IASU) has been designed for Endura HP PVDTM sputtering sources. The integrated design reduces cable length from unit to source and reduces electrical energy stored in the cable. Active arc handling mode, proactive arc prevention mode, and passive by-pass arc counting mode are incorporated into the same unit. The active mode is designed to quickly respond to chamber conditions, like a large chamber voltage drop, that signals a arc. The self run mode is designed to proactively prevent arc formation by pulsing and reversing target voltage at 50 kHz. The design of the IASU, also called mini small package arc repression circuit--low energy unit (mini Sparc-le), has been optimized for various DC magnetron sources, plasma stability, chamber impedance, power matching, CE MARK test, and power dissipation. Process characterization with Ti, TiN and Al sputtering indicates that the unit has little adverse impact on film properties. Mini Sparc-le unit has been shown here to significantly reduce splats occurrence in Al sputtering. Marathon test of the unit with Ti/TiN test demonstrated the unit's reliability and its ability to reduce sensitivity of defects to target characteristics.

Sediment source fingerprinting as an aid to catchment management: A review of the current state of knowledge and a methodological decision-tree for end-users.

PubMed

Collins, A L; Pulley, S; Foster, I D L; Gellis, A; Porto, P; Horowitz, A J

2017-06-01

The growing awareness of the environmental significance of fine-grained sediment fluxes through catchment systems continues to underscore the need for reliable information on the principal sources of this material. Source estimates are difficult to obtain using traditional monitoring techniques, but sediment source fingerprinting or tracing procedures, have emerged as a potentially valuable alternative. Despite the rapidly increasing numbers of studies reporting the use of sediment source fingerprinting, several key challenges and uncertainties continue to hamper consensus among the international scientific community on key components of the existing methodological procedures. Accordingly, this contribution reviews and presents recent developments for several key aspects of fingerprinting, namely: sediment source classification, catchment source and target sediment sampling, tracer selection, grain size issues, tracer conservatism, source apportionment modelling, and assessment of source predictions using artificial mixtures. Finally, a decision-tree representing the current state of knowledge is presented, to guide end-users in applying the fingerprinting approach. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

The internet as a source of health information in three disparate communities.

PubMed

Dart, Jared

2008-08-01

A survey questionnaire was designed and implemented across three different communities to determine the current utilisation, importance, trust and future preference for the internet as a source of health information in three different socioeconomic groups. The following were the key results. Fewer respondents in the low socioeconomic group accessed online health information than the mid-high socioeconomic or university samples. The internet was a much more important source of health information for the university sample. The use of online health information and the importance ascribed to the internet as a source of health information was related to home internet access and the frequency of internet use in all three populations. Most respondents do not bring online health information to their doctor (>70% of those who access online health information). Age alone did not relate to the current use of the internet as a source of health information. Most respondents in all populations did not trust the internet. In all populations the internet was a more preferred source of health information than its current use would suggest, especially among those with home internet access and frequent users of the internet.

A New Electron Source for Laboratory Simulation of the Space Environment

NASA Technical Reports Server (NTRS)

Krause, Linda Habash; Everding, Daniel; Bonner, Mathew; Swan, Brian

2012-01-01

We have developed a new collimated electron source called the Photoelectron Beam Generator (PEBG) for laboratory and spaceflight applications. This technology is needed to replace traditional cathodes because of serious fundamental weaknesses with the present state of the art. Filament cathodes suffer from numerous practical problems, even if expertly designed, including the dependence of electron emission on filament temperature, short lifetimes (approx 100 hours), and relatively high power (approx 10s of W). Other types of cathodes have solved some of these problems, but they are plagued with other difficult problems, such as the Spindt cathode's extreme sensitivity to molecular oxygen. None to date have been able to meet the demand of long lifetime, robust packaging, and precision energy and flux control. This new cathode design avoids many common pitfalls of traditional cathodes. Specifically, there are no fragile parts, no sensitivity to oxygen, no intrinsic emission dependencies on device temperature, and no vacuum requirements for protecting the source from contamination or damage. Recent advances in high-brightness Light Emitting Diodes (LEDs) have provided the key enabling technology for this new electron source. The LEDs are used to photoeject electrons off a target material of a low work-function, and these photoelectrons are subsequently focused into a laminar beam using electrostatic lenses. The PEBG works by illuminating a target material and steering photoelectrons into a laminar beam using electrostatic lenses

Open-Source Assisted Laboratory Automation through Graphical User Interfaces and 3D Printers: Application to Equipment Hyphenation for Higher-Order Data Generation.

PubMed

Siano, Gabriel G; Montemurro, Milagros; Alcaráz, Mirta R; Goicoechea, Héctor C

2017-10-17

Higher-order data generation implies some automation challenges, which are mainly related to the hidden programming languages and electronic details of the equipment. When techniques and/or equipment hyphenation are the key to obtaining higher-order data, the required simultaneous control of them demands funds for new hardware, software, and licenses, in addition to very skilled operators. In this work, we present Design of Inputs-Outputs with Sikuli (DIOS), a free and open-source code program that provides a general framework for the design of automated experimental procedures without prior knowledge of programming or electronics. Basically, instruments and devices are considered as nodes in a network, and every node is associated both with physical and virtual inputs and outputs. Virtual components, such as graphical user interfaces (GUIs) of equipment, are handled by means of image recognition tools provided by Sikuli scripting language, while handling of their physical counterparts is achieved using an adapted open-source three-dimensional (3D) printer. Two previously reported experiments of our research group, related to fluorescence matrices derived from kinetics and high-performance liquid chromatography, were adapted to be carried out in a more automated fashion. Satisfactory results, in terms of analytical performance, were obtained. Similarly, advantages derived from open-source tools assistance could be appreciated, mainly in terms of lesser intervention of operators and cost savings.

J3Gen: A PRNG for Low-Cost Passive RFID

PubMed Central

Melià-Seguí, Joan; Garcia-Alfaro, Joaquin; Herrera-Joancomartí, Jordi

2013-01-01

Pseudorandom number generation (PRNG) is the main security tool in low-cost passive radio-frequency identification (RFID) technologies, such as EPC Gen2. We present a lightweight PRNG design for low-cost passive RFID tags, named J3Gen. J3Gen is based on a linear feedback shift register (LFSR) configured with multiple feedback polynomials. The polynomials are alternated during the generation of sequences via a physical source of randomness. J3Gen successfully handles the inherent linearity of LFSR based PRNGs and satisfies the statistical requirements imposed by the EPC Gen2 standard. A hardware implementation of J3Gen is presented and evaluated with regard to different design parameters, defining the key-equivalence security and nonlinearity of the design. The results of a SPICE simulation confirm the power-consumption suitability of the proposal. PMID:23519344

ESS Cryogenic System Process Design

NASA Astrophysics Data System (ADS)

Arnold, P.; Hees, W.; Jurns, J.; Su, X. T.; Wang, X. L.; Weisend, J. G., II

2015-12-01

The European Spallation Source (ESS) is a neutron-scattering facility funded and supported in collaboration with 17 European countries in Lund, Sweden. Cryogenic cooling at ESS is vital particularly for the linear accelerator, the hydrogen target moderators, a test stand for cryomodules, the neutron instruments and their sample environments. The paper will focus on specific process design criteria, design decisions and their motivations for the helium cryoplants and auxiliary equipment. Key issues for all plants and their process concepts are energy efficiency, reliability, smooth turn-down behaviour and flexibility. The accelerator cryoplant (ACCP) and the target moderator cryoplant (TMCP) in particular need to be prepared for a range of refrigeration capacities due to the intrinsic uncertainties regarding heat load definitions. Furthermore the paper addresses questions regarding process arrangement, 2 K cooling methodology, LN2 precooling, helium storage, helium purification and heat recovery.

Data Collection for Mental Health Studies Through Digital Platforms: Requirements and Design of a Prototype

PubMed Central

Triana Hoyos, Ana Maria; Alakörkkö, Tuomas; Kaski, Kimmo; Saramäki, Jari; Isometsä, Erkki; Darst, Richard K

2017-01-01

Background Mental and behavioral disorders are the main cause of disability worldwide. However, their diagnosis is challenging due to a lack of reliable biomarkers; current detection is based on structured clinical interviews which can be biased by the patient’s recall ability, affective state, changing in temporal frames, etc. While digital platforms have been introduced as a possible solution to this complex problem, there is little evidence on the extent of usability and usefulness of these platforms. Therefore, more studies where digital data is collected in larger scales are needed to collect scientific evidence on the capacities of these platforms. Most of the existing platforms for digital psychiatry studies are designed as monolithic systems for a certain type of study; publications from these studies focus on their results, rather than the design features of the data collection platform. Inevitably, more tools and platforms will emerge in the near future to fulfill the need for digital data collection for psychiatry. Currently little knowledge is available from existing digital platforms for future data collection platforms to build upon. Objective The objective of this work was to identify the most important features for designing a digital platform for data collection for mental health studies, and to demonstrate a prototype platform that we built based on these design features. Methods We worked closely in a multidisciplinary collaboration with psychiatrists, software developers, and data scientists and identified the key features which could guarantee short-term and long-term stability and usefulness of the platform from the designing stage to data collection and analysis of collected data. Results The key design features that we identified were flexibility of access control, flexibility of data sources, and first-order privacy protection. We also designed the prototype platform Non-Intrusive Individual Monitoring Architecture (Niima), where we implemented these key design features. We described why each of these features are important for digital data collection for psychiatry, gave examples of projects where Niima was used or is going to be used in the future, and demonstrated how incorporating these design principles opens new possibilities for studies. Conclusions The new methods of digital psychiatry are still immature and need further research. The design features we suggested are a first step to design platforms which can adapt to the upcoming requirements of digital psychiatry. PMID:28600276

Key Design Elements of a Data Utility for National Biosurveillance: Event-driven Architecture, Caching, and Web Service Model

PubMed Central

Tsui, Fu-Chiang; Espino, Jeremy U.; Weng, Yan; Choudary, Arvinder; Su, Hoah-Der; Wagner, Michael M.

2005-01-01

The National Retail Data Monitor (NRDM) has monitored over-the-counter (OTC) medication sales in the United States since December 2002. The NRDM collects data from over 18,600 retail stores and processes over 0.6 million sales records per day. This paper describes key architectural features that we have found necessary for a data utility component in a national biosurveillance system. These elements include event-driven architecture to provide analyses of data in near real time, multiple levels of caching to improve query response time, high availability through the use of clustered servers, scalable data storage through the use of storage area networks and a web-service function for interoperation with affiliated systems. The methods and architectural principles are relevant to the design of any production data utility for public health surveillance—systems that collect data from multiple sources in near real time for use by analytic programs and user interfaces that have substantial requirements for time-series data aggregated in multiple dimensions. PMID:16779138

Commentary: pediatric eHealth interventions: common challenges during development, implementation, and dissemination.

PubMed

Wu, Yelena P; Steele, Ric G; Connelly, Mark A; Palermo, Tonya M; Ritterband, Lee M

2014-07-01

To provide an overview of common challenges that pediatric eHealth researchers may encounter when planning, developing, testing, and disseminating eHealth interventions along with proposed solutions for addressing these challenges. The article draws on the existing eHealth literature and the authors' collective experience in pediatric eHealth research. The challenges associated with eHealth interventions and their proposed solutions are multifaceted and cut across a number of areas from eHealth program development through dissemination. Collaboration with a range of individuals (e.g., multidisciplinary colleagues, commercial entities, primary stakeholders) is the key to eHealth intervention success. To ensure adequate resources for design, development, and planning for sustainability, a number of public and private sources of funding are available. A study design that addresses ethical concerns and security issues is critical to ensure scientific integrity and intervention dissemination. Table I summarizes key issues to consider during eHealth intervention development, testing, and dissemination. © The Author 2014. Published by Oxford University Press on behalf of the Society of Pediatric Psychology. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Design of batch audio/video conversion platform based on JavaEE

NASA Astrophysics Data System (ADS)

Cui, Yansong; Jiang, Lianpin

2018-03-01

With the rapid development of digital publishing industry, the direction of audio / video publishing shows the diversity of coding standards for audio and video files, massive data and other significant features. Faced with massive and diverse data, how to quickly and efficiently convert to a unified code format has brought great difficulties to the digital publishing organization. In view of this demand and present situation in this paper, basing on the development architecture of Sptring+SpringMVC+Mybatis, and combined with the open source FFMPEG format conversion tool, a distributed online audio and video format conversion platform with a B/S structure is proposed. Based on the Java language, the key technologies and strategies designed in the design of platform architecture are analyzed emphatically in this paper, designing and developing a efficient audio and video format conversion system, which is composed of “Front display system”, "core scheduling server " and " conversion server ". The test results show that, compared with the ordinary audio and video conversion scheme, the use of batch audio and video format conversion platform can effectively improve the conversion efficiency of audio and video files, and reduce the complexity of the work. Practice has proved that the key technology discussed in this paper can be applied in the field of large batch file processing, and has certain practical application value.

Design Optimization for the Measurement Accuracy Improvement of a Large Range Nanopositioning Stage

PubMed Central

Torralba, Marta; Yagüe-Fabra, José Antonio; Albajez, José Antonio; Aguilar, Juan José

2016-01-01

Both an accurate machine design and an adequate metrology loop definition are critical factors when precision positioning represents a key issue for the final system performance. This article discusses the error budget methodology as an advantageous technique to improve the measurement accuracy of a 2D-long range stage during its design phase. The nanopositioning platform NanoPla is here presented. Its specifications, e.g., XY-travel range of 50 mm × 50 mm and sub-micrometric accuracy; and some novel designed solutions, e.g., a three-layer and two-stage architecture are described. Once defined the prototype, an error analysis is performed to propose improvement design features. Then, the metrology loop of the system is mathematically modelled to define the propagation of the different sources. Several simplifications and design hypothesis are justified and validated, including the assumption of rigid body behavior, which is demonstrated after a finite element analysis verification. The different error sources and their estimated contributions are enumerated in order to conclude with the final error values obtained from the error budget. The measurement deviations obtained demonstrate the important influence of the working environmental conditions, the flatness error of the plane mirror reflectors and the accurate manufacture and assembly of the components forming the metrological loop. Thus, a temperature control of ±0.1 °C results in an acceptable maximum positioning error for the developed NanoPla stage, i.e., 41 nm, 36 nm and 48 nm in X-, Y- and Z-axis, respectively. PMID:26761014

Designing Tracking Software for Image-Guided Surgery Applications: IGSTK Experience

PubMed Central

Enquobahrie, Andinet; Gobbi, David; Turek, Matt; Cheng, Patrick; Yaniv, Ziv; Lindseth, Frank; Cleary, Kevin

2009-01-01

Objective Many image-guided surgery applications require tracking devices as part of their core functionality. The Image-Guided Surgery Toolkit (IGSTK) was designed and developed to interface tracking devices with software applications incorporating medical images. Methods IGSTK was designed as an open source C++ library that provides the basic components needed for fast prototyping and development of image-guided surgery applications. This library follows a component-based architecture with several components designed for specific sets of image-guided surgery functions. At the core of the toolkit is the tracker component that handles communication between a control computer and navigation device to gather pose measurements of surgical instruments present in the surgical scene. The representations of the tracked instruments are superimposed on anatomical images to provide visual feedback to the clinician during surgical procedures. Results The initial version of the IGSTK toolkit has been released in the public domain and several trackers are supported. The toolkit and related information are available at www.igstk.org. Conclusion With the increased popularity of minimally invasive procedures in health care, several tracking devices have been developed for medical applications. Designing and implementing high-quality and safe software to handle these different types of trackers in a common framework is a challenging task. It requires establishing key software design principles that emphasize abstraction, extensibility, reusability, fault-tolerance, and portability. IGSTK is an open source library that satisfies these needs for the image-guided surgery community. PMID:20037671

The California Baseline Methane Survey

NASA Astrophysics Data System (ADS)

Duren, R. M.; Thorpe, A. K.; Hopkins, F. M.; Rafiq, T.; Bue, B. D.; Prasad, K.; Mccubbin, I.; Miller, C. E.

2017-12-01

The California Baseline Methane Survey is the first systematic, statewide assessment of methane point source emissions. The objectives are to reduce uncertainty in the state's methane budget and to identify emission mitigation priorities for state and local agencies, utilities and facility owners. The project combines remote sensing of large areas with airborne imaging spectroscopy and spatially resolved bottom-up data sets to detect, quantify and attribute emissions from diverse sectors including agriculture, waste management, oil and gas production and the natural gas supply chain. Phase 1 of the project surveyed nearly 180,000 individual facilities and infrastructure components across California in 2016 - achieving completeness rates ranging from 20% to 100% per emission sector at < 5 meters spatial resolution. Additionally, intensive studies of key areas and sectors were performed to assess source persistence and variability at times scales ranging from minutes to months. Phase 2 of the project continues with additional data collection in Spring and Fall 2017. We describe the survey design and measurement, modeling and analysis methods. We present initial findings regarding the spatial, temporal and sectoral distribution of methane point source emissions in California and their estimated contribution to the state's total methane budget. We provide case-studies and lessons learned about key sectors including examples where super-emitters were identified and mitigated. We summarize challenges and recommendations for future methane research, inventories and mitigation guidance within and beyond California.

What Made Berkeley Great? The Sources of Berkeley's Sustained Academic Excellence. Research & Occasional Paper Series CSHE.3.11

ERIC Educational Resources Information Center

Breslauer, George W.

2011-01-01

University of California (UC) Berkeley's chief academic officer explores the historical sources of Berkeley' academic excellence. He identifies five key factors: (1) wealth from many sources; (2) supportive and skilled governors; (3) leadership from key UC presidents; (4) the pioneering ethos within the State of California; and (5) a process of…

Experimental Measurement-Device-Independent Quantum Key Distribution

NASA Astrophysics Data System (ADS)

Liu, Yang; Chen, Teng-Yun; Wang, Liu-Jun; Liang, Hao; Shentu, Guo-Liang; Wang, Jian; Cui, Ke; Yin, Hua-Lei; Liu, Nai-Le; Li, Li; Ma, Xiongfeng; Pelc, Jason S.; Fejer, M. M.; Peng, Cheng-Zhi; Zhang, Qiang; Pan, Jian-Wei

2013-09-01

Quantum key distribution is proven to offer unconditional security in communication between two remote users with ideal source and detection. Unfortunately, ideal devices never exist in practice and device imperfections have become the targets of various attacks. By developing up-conversion single-photon detectors with high efficiency and low noise, we faithfully demonstrate the measurement-device-independent quantum-key-distribution protocol, which is immune to all hacking strategies on detection. Meanwhile, we employ the decoy-state method to defend attacks on a nonideal source. By assuming a trusted source scenario, our practical system, which generates more than a 25 kbit secure key over a 50 km fiber link, serves as a stepping stone in the quest for unconditionally secure communications with realistic devices.

Experimental measurement-device-independent quantum key distribution.

PubMed

Liu, Yang; Chen, Teng-Yun; Wang, Liu-Jun; Liang, Hao; Shentu, Guo-Liang; Wang, Jian; Cui, Ke; Yin, Hua-Lei; Liu, Nai-Le; Li, Li; Ma, Xiongfeng; Pelc, Jason S; Fejer, M M; Peng, Cheng-Zhi; Zhang, Qiang; Pan, Jian-Wei

2013-09-27

Quantum key distribution is proven to offer unconditional security in communication between two remote users with ideal source and detection. Unfortunately, ideal devices never exist in practice and device imperfections have become the targets of various attacks. By developing up-conversion single-photon detectors with high efficiency and low noise, we faithfully demonstrate the measurement-device-independent quantum-key-distribution protocol, which is immune to all hacking strategies on detection. Meanwhile, we employ the decoy-state method to defend attacks on a nonideal source. By assuming a trusted source scenario, our practical system, which generates more than a 25 kbit secure key over a 50 km fiber link, serves as a stepping stone in the quest for unconditionally secure communications with realistic devices.

Measurement-device-independent quantum key distribution with multiple crystal heralded source with post-selection

NASA Astrophysics Data System (ADS)

Chen, Dong; Shang-Hong, Zhao; MengYi, Deng

2018-03-01

The multiple crystal heralded source with post-selection (MHPS), originally introduced to improve the single-photon character of the heralded source, has specific applications for quantum information protocols. In this paper, by combining decoy-state measurement-device-independent quantum key distribution (MDI-QKD) with spontaneous parametric downconversion process, we present a modified MDI-QKD scheme with MHPS where two architectures are proposed corresponding to symmetric scheme and asymmetric scheme. The symmetric scheme, which linked by photon switches in a log-tree structure, is adopted to overcome the limitation of the current low efficiency of m-to-1 optical switches. The asymmetric scheme, which shows a chained structure, is used to cope with the scalability issue with increase in the number of crystals suffered in symmetric scheme. The numerical simulations show that our modified scheme has apparent advances both in transmission distance and key generation rate compared to the original MDI-QKD with weak coherent source and traditional heralded source with post-selection. Furthermore, the recent advances in integrated photonics suggest that if built into a single chip, the MHPS might be a practical alternative source in quantum key distribution tasks requiring single photons to work.

Novel single photon sources for new generation of quantum communications

DTIC Science & Technology

2017-06-13

be used as building blocks for quantum cryptography and quantum key distribution There were numerous important achievements for the projects in the...single photon sources that will be used as build- ing blocks for quantum cryptography and quantum key distribution There were numerous im- portant...and enable absolutely secured information transfer between distant nodes – key prerequisite for quantum cryptography . Experiment: the experimental

Multi-octave spectral beam combiner on ultra-broadband photonic integrated circuit platform.

PubMed

Stanton, Eric J; Heck, Martijn J R; Bovington, Jock; Spott, Alexander; Bowers, John E

2015-05-04

We present the design of a novel platform that is able to combine optical frequency bands spanning 4.2 octaves from ultraviolet to mid-wave infrared into a single, low M2 output waveguide. We present the design and realization of a key component in this platform that combines the wavelength bands of 350 nm - 1500 nm and 1500 nm - 6500 nm with demonstrated efficiency greater than 90% in near-infrared and mid-wave infrared. The multi-octave spectral beam combiner concept is realized using an integrated platform with silicon nitride waveguides and silicon waveguides. Simulated bandwidth is shown to be over four octaves, and measured bandwidth is shown over two octaves, limited by the availability of sources.

Cost-efficiency trade-off and the design of thermoelectric power generators.

PubMed

Yazawa, Kazuaki; Shakouri, Ali

2011-09-01

The energy conversion efficiency of today's thermoelectric generators is significantly lower than that of conventional mechanical engines. Almost all of the existing research is focused on materials to improve the conversion efficiency. Here we propose a general framework to study the cost-efficiency trade-off for thermoelectric power generation. A key factor is the optimization of thermoelectric modules together with their heat source and heat sinks. Full electrical and thermal co-optimization yield a simple analytical expression for optimum design. Based on this model, power output per unit mass can be maximized. We show that the fractional area coverage of thermoelectric elements in a module could play a significant role in reducing the cost of power generation systems.

Introduction to spallation physics and spallation-target design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Russell, G.J.; Pitcher, E.J.; Daemen, L.L.

1995-10-01

When coupled with the spallation process in appropriate target materials, high-power accelerators can be used to produce large numbers of neutrons, thus providing an alternate method to the use of nuclear reactors for this purpose. Spallation offers exciting new possibilities for generating intense neutron fluxes for a variety of applications, including: (a) spallation-neutron sources for materials science research; (b) accelerator-based production of tritium; (c) accelerator-based transmutation of waste; (d) accelerator-based destruction of plutonium; and (e) radioisotope production for medical and energy applications. Target design plays a key role in these applications, with neutron production/leakage being strongly dependent on the incidentmore » particle type and energy, and target material and geometry.« less

NIMBUS: A Near-Infrared Multi-Band Ultraprecise Spectroimager for SOFIA

NASA Technical Reports Server (NTRS)

McElwain, Michael W.; Mandell, Avi; Woodgate, Bruce E.; Spiegel, David S.; Madhusudhan, Nikku; Amatucci, Edward; Blake, Cullen; Budinoff, Jason; Burgasser, Adam; Burrows, Adam;

Microbes to Biomes at Berkeley Lab

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2015-10-28

Microbes are the Earth's most abundant and diverse form of life. Berkeley Lab's Microbes to Biomes initiative -- which will take advantage of research expertise at the Joint Genome Institute, Advanced Light Source, Molecular Foundry, and the new computational science facility -- is designed to explore and reveal the interactions of microbes with one another and with their environment. Microbes power our planet’s biogeochemical cycles, provide nutrients to our plants, purify our water and are integral components in keeping the human body free of disease and may hold the key to the Earth’s future.

A two-metric proposal to specify the color-rendering properties of light sources for retail lighting

NASA Astrophysics Data System (ADS)

Freyssinier, Jean Paul; Rea, Mark

2010-08-01

Lighting plays an important role in supporting retail operations, from attracting customers, to enabling the evaluation of merchandise, to facilitating the completion of the sale. Lighting also contributes to the identity, comfort, and visual quality of a retail store. With the increasing availability and quality of white LEDs, retail lighting specifiers are now considering LED lighting in stores. The color rendering of light sources is a key factor in supporting retail lighting goals and thus influences a light source's acceptance by users and specifiers. However, there is limited information on what consumers' color preferences are, and metrics used to describe the color properties of light sources often are equivocal and fail to predict preference. The color rendering of light sources is described in the industry solely by the color rendering index (CRI), which is only indirectly related to human perception. CRI is intended to characterize the appearance of objects illuminated by the source and is increasingly being challenged because new sources are being developed with increasingly exotic spectral power distributions. This paper discusses how CRI might be augmented to better use it in support of the design objectives for retail merchandising. The proposed guidelines include the use of gamut area index as a complementary metric to CRI for assuring good color rendering.

Initial Performance of the Aspect System on the Chandra Observatory: Post-Facto Aspect Reconstruction

NASA Technical Reports Server (NTRS)

Aldcroft, T.; Karovska, M.; Cresitello-Dittmar, M.; Cameron, R.

2000-01-01

The aspect system of the Chandra Observatory plays a key role in realizing the full potential of Chandra's x-ray optics and detectors. To achieve the highest spatial and spectral resolution (for grating observations), an accurate post-facto time history of the spacecraft attitude and internal alignment is needed. The CXC has developed a suite of tools which process sensor data from the aspect camera assembly and gyroscopes, and produce the spacecraft aspect solution. In this poster, the design of the aspect pipeline software is briefly described, followed by details of aspect system performance during the first eight months of flight. The two key metrics of aspect performance are: image reconstruction accuracy, which measures the x-ray image blurring introduced by aspect; and celestial location, which is the accuracy of detected source positions in absolute sky coordinates.

Triple-mode single-transistor graphene amplifier and its applications.

PubMed

Yang, Xuebei; Liu, Guanxiong; Balandin, Alexander A; Mohanram, Kartik

2010-10-26

We propose and experimentally demonstrate a triple-mode single-transistor graphene amplifier utilizing a three-terminal back-gated single-layer graphene transistor. The ambipolar nature of electronic transport in graphene transistors leads to increased amplifier functionality as compared to amplifiers built with unipolar semiconductor devices. The ambipolar graphene transistors can be configured as n-type, p-type, or hybrid-type by changing the gate bias. As a result, the single-transistor graphene amplifier can operate in the common-source, common-drain, or frequency multiplication mode, respectively. This in-field controllability of the single-transistor graphene amplifier can be used to realize the modulation necessary for phase shift keying and frequency shift keying, which are widely used in wireless applications. It also offers new opportunities for designing analog circuits with simpler structure and higher integration densities for communications applications.

The image-guided surgery toolkit IGSTK: an open source C++ software toolkit.

PubMed

Enquobahrie, Andinet; Cheng, Patrick; Gary, Kevin; Ibanez, Luis; Gobbi, David; Lindseth, Frank; Yaniv, Ziv; Aylward, Stephen; Jomier, Julien; Cleary, Kevin

2007-11-01

This paper presents an overview of the image-guided surgery toolkit (IGSTK). IGSTK is an open source C++ software library that provides the basic components needed to develop image-guided surgery applications. It is intended for fast prototyping and development of image-guided surgery applications. The toolkit was developed through a collaboration between academic and industry partners. Because IGSTK was designed for safety-critical applications, the development team has adopted lightweight software processes that emphasizes safety and robustness while, at the same time, supporting geographically separated developers. A software process that is philosophically similar to agile software methods was adopted emphasizing iterative, incremental, and test-driven development principles. The guiding principle in the architecture design of IGSTK is patient safety. The IGSTK team implemented a component-based architecture and used state machine software design methodologies to improve the reliability and safety of the components. Every IGSTK component has a well-defined set of features that are governed by state machines. The state machine ensures that the component is always in a valid state and that all state transitions are valid and meaningful. Realizing that the continued success and viability of an open source toolkit depends on a strong user community, the IGSTK team is following several key strategies to build an active user community. These include maintaining a users and developers' mailing list, providing documentation (application programming interface reference document and book), presenting demonstration applications, and delivering tutorial sessions at relevant scientific conferences.

Long-distance entanglement-based quantum key distribution experiment using practical detectors.

PubMed

Takesue, Hiroki; Harada, Ken-Ichi; Tamaki, Kiyoshi; Fukuda, Hiroshi; Tsuchizawa, Tai; Watanabe, Toshifumi; Yamada, Koji; Itabashi, Sei-Ichi

2010-08-02

We report an entanglement-based quantum key distribution experiment that we performed over 100 km of optical fiber using a practical source and detectors. We used a silicon-based photon-pair source that generated high-purity time-bin entangled photons, and high-speed single photon detectors based on InGaAs/InP avalanche photodiodes with the sinusoidal gating technique. To calculate the secure key rate, we employed a security proof that validated the use of practical detectors. As a result, we confirmed the successful generation of sifted keys over 100 km of optical fiber with a key rate of 4.8 bit/s and an error rate of 9.1%, with which we can distill secure keys with a key rate of 0.15 bit/s.

An observational study of the accuracy and completeness of an anesthesia information management system: recommendations for documentation system changes.

PubMed

Wilbanks, Bryan A; Moss, Jacqueline A; Berner, Eta S

2013-08-01

Anesthesia information management systems must often be tailored to fit the environment in which they are implemented. Extensive customization necessitates that systems be analyzed for both accuracy and completeness of documentation design to ensure that the final record is a true representation of practice. The purpose of this study was to determine the accuracy of a recently installed system in the capture of key perianesthesia data. This study used an observational design and was conducted using a convenience sample of nurse anesthetists. Observational data of the nurse anesthetists'delivery of anesthesia care were collected using a touch-screen tablet computer utilizing an Access database customized observational data collection tool. A questionnaire was also administered to these nurse anesthetists to assess perceived accuracy, completeness, and satisfaction with the electronic documentation system. The major sources of data not documented in the system were anesthesiologist presence (20%) and placement of intravenous lines (20%). The major sources of inaccuracies in documentation were gas flow rates (45%), medication administration times (30%), and documentation of neuromuscular function testing (20%)-all of the sources of inaccuracies were related to the use of charting templates that were not altered to reflect the actual interventions performed.

Measurement-device-independent quantum communication with an untrusted source

NASA Astrophysics Data System (ADS)

Xu, Feihu

2015-07-01

Measurement-device-independent quantum key distribution (MDI-QKD) can provide enhanced security compared to traditional QKD, and it constitutes an important framework for a quantum network with an untrusted network server. Still, a key assumption in MDI-QKD is that the sources are trusted. We propose here a MDI quantum network with a single untrusted source. We have derived a complete proof of the unconditional security of MDI-QKD with an untrusted source. Using simulations, we have considered various real-life imperfections in its implementation, and the simulation results show that MDI-QKD with an untrusted source provides a key generation rate that is close to the rate of initial MDI-QKD in the asymptotic setting. Our work proves the feasibility of the realization of a quantum network. The network users need only low-cost modulation devices, and they can share both an expensive detector and a complicated laser provided by an untrusted network server.

Amanzi: An Open-Source Multi-process Simulator for Environmental Applications

NASA Astrophysics Data System (ADS)

Moulton, J. D.; Molins, S.; Johnson, J. N.; Coon, E.; Lipnikov, K.; Day, M.; Barker, E.

2014-12-01

The Advanced Simulation Capabililty for Environmental Management (ASCEM) program is developing an approach and open-source tool suite for standardized risk and performance assessments at legacy nuclear waste sites. These assessments begin with simplified models, and add geometric and geologic complexity as understanding is gained. The Platform toolsets (Akuna) generates these conceptual models and Amanzi provides the computational engine to perform the simulations, returning the results for analysis and visualization. In this presentation we highlight key elements of the design, algorithms and implementations used in Amanzi. In particular, the hierarchical and modular design is aligned with the coupled processes being sumulated, and naturally supports a wide range of model complexity. This design leverages a dynamic data manager and the synergy of two graphs (one from the high-level perspective of the models the other from the dependencies of the variables in the model) to enable this flexible model configuration at run time. Moreover, to model sites with complex hydrostratigraphy, as well as engineered systems, we are developing a dual unstructured/structured capability. Recently, these capabilities have been collected in a framework named Arcos, and efforts have begun to improve interoperability between the unstructured and structured AMR approaches in Amanzi. To leverage a range of biogeochemistry capability from the community (e.g., CrunchFlow, PFLOTRAN, etc.), a biogeochemistry interface library was developed called Alquimia. To ensure that Amanzi is truly an open-source community code we require a completely open-source tool chain for our development. We will comment on elements of this tool chain, including the testing and documentation development tools such as docutils, and Sphinx. Finally, we will show simulation results from our phased demonstrations, including the geochemically complex Savannah River F-Area seepage basins.

A risk-based approach to management of leachables utilizing statistical analysis of extractables.

PubMed

Stults, Cheryl L M; Mikl, Jaromir; Whelehan, Oliver; Morrical, Bradley; Duffield, William; Nagao, Lee M

2015-04-01

To incorporate quality by design concepts into the management of leachables, an emphasis is often put on understanding the extractable profile for the materials of construction for manufacturing disposables, container-closure, or delivery systems. Component manufacturing processes may also impact the extractable profile. An approach was developed to (1) identify critical components that may be sources of leachables, (2) enable an understanding of manufacturing process factors that affect extractable profiles, (3) determine if quantitative models can be developed that predict the effect of those key factors, and (4) evaluate the practical impact of the key factors on the product. A risk evaluation for an inhalation product identified injection molding as a key process. Designed experiments were performed to evaluate the impact of molding process parameters on the extractable profile from an ABS inhaler component. Statistical analysis of the resulting GC chromatographic profiles identified processing factors that were correlated with peak levels in the extractable profiles. The combination of statistically significant molding process parameters was different for different types of extractable compounds. ANOVA models were used to obtain optimal process settings and predict extractable levels for a selected number of compounds. The proposed paradigm may be applied to evaluate the impact of material composition and processing parameters on extractable profiles and utilized to manage product leachables early in the development process and throughout the product lifecycle.

Factors that influence career progression among postdoctoral clinical academics: a scoping review of the literature

PubMed Central

Ranieri, Veronica; Barratt, Helen; Fulop, Naomi; Rees, Geraint

2016-01-01

Background The future of academic medicine is uncertain. Concerns regarding the future availability of qualified and willing trainee clinical academics have been raised worldwide. Of significant concern is our failure to retain postdoctoral trainee clinical academics, who are likely to be our next generation of leaders in scientific discovery. Objectives To review the literature about factors that may influence postdoctoral career progression in early career clinical academics. Design This study employed a scoping review method. Three reviewers separately assessed whether the articles found fit the inclusion criteria. Data sources PubMed, Scopus, Web of Science and Google Scholar (1991–2015). Article selection The review encompassed a broad search of English language studies published anytime up to November 2015. All articles were eligible for inclusion, including research papers employing either quantitative or qualitative methods, as well as editorials and other summary articles. Data extraction Data extracted from included publications were charted according to author(s), sample population, study design, key findings, country of origin and year of publication. Results Our review identified 6 key influences: intrinsic motivation, work–life balance, inclusiveness, work environment, mentorship and availability of funding. It also detected significant gaps within the literature about these influences. Conclusions Three key steps are proposed to help support postdoctoral trainee clinical academics. These focus on ensuring that researchers feel encouraged in their workplace, involved in collaborative dialogue with key stakeholders and able to access reliable information regarding their chosen career pathway. Finally, we highlight recommendations for future research. PMID:27798036

Continuous-variable quantum key distribution with Gaussian source noise

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shen Yujie; Peng Xiang; Yang Jian

2011-05-15

Source noise affects the security of continuous-variable quantum key distribution (CV QKD) and is difficult to analyze. We propose a model to characterize Gaussian source noise through introducing a neutral party (Fred) who induces the noise with a general unitary transformation. Without knowing Fred's exact state, we derive the security bounds for both reverse and direct reconciliations and show that the bound for reverse reconciliation is tight.

Realizing the measure-device-independent quantum-key-distribution with passive heralded-single photon sources

PubMed Central

Wang, Qin; Zhou, Xing-Yu; Guo, Guang-Can

2016-01-01

In this paper, we put forward a new approach towards realizing measurement-device-independent quantum key distribution with passive heralded single-photon sources. In this approach, both Alice and Bob prepare the parametric down-conversion source, where the heralding photons are labeled according to different types of clicks from the local detectors, and the heralded ones can correspondingly be marked with different tags at the receiver’s side. Then one can obtain four sets of data through using only one-intensity of pump light by observing different kinds of clicks of local detectors. By employing the newest formulae to do parameter estimation, we could achieve very precise prediction for the two-single-photon pulse contribution. Furthermore, by carrying out corresponding numerical simulations, we compare the new method with other practical schemes of measurement-device-independent quantum key distribution. We demonstrate that our new proposed passive scheme can exhibit remarkable improvement over the conventional three-intensity decoy-state measurement-device-independent quantum key distribution with either heralded single-photon sources or weak coherent sources. Besides, it does not need intensity modulation and can thus diminish source-error defects existing in several other active decoy-state methods. Therefore, if taking intensity modulating errors into account, our new method will show even more brilliant performance. PMID:27759085

Singular value decomposition metrics show limitations of detector design in diffuse fluorescence tomography

PubMed Central

Leblond, Frederic; Tichauer, Kenneth M.; Pogue, Brian W.

2010-01-01

The spatial resolution and recovered contrast of images reconstructed from diffuse fluorescence tomography data are limited by the high scattering properties of light propagation in biological tissue. As a result, the image reconstruction process can be exceedingly vulnerable to inaccurate prior knowledge of tissue optical properties and stochastic noise. In light of these limitations, the optimal source-detector geometry for a fluorescence tomography system is non-trivial, requiring analytical methods to guide design. Analysis of the singular value decomposition of the matrix to be inverted for image reconstruction is one potential approach, providing key quantitative metrics, such as singular image mode spatial resolution and singular data mode frequency as a function of singular mode. In the present study, these metrics are used to analyze the effects of different sources of noise and model errors as related to image quality in the form of spatial resolution and contrast recovery. The image quality is demonstrated to be inherently noise-limited even when detection geometries were increased in complexity to allow maximal tissue sampling, suggesting that detection noise characteristics outweigh detection geometry for achieving optimal reconstructions. PMID:21258566

The Network Structure Underlying the Earth Observation Assessment

NASA Astrophysics Data System (ADS)

Vitkin, S.; Doane, W. E. J.; Mary, J. C.

2017-12-01

The Earth Observations Assessment (EOA 2016) is a multiyear project designed to assess the effectiveness of civil earth observation data sources (instruments, sensors, models, etc.) on societal benefit areas (SBAs) for the United States. Subject matter experts (SMEs) provided input and scored how data sources inform products, product groups, key objectives, SBA sub-areas, and SBAs in an attempt to quantify the relationships between data sources and SBAs. The resulting data were processed by Integrated Applications Incorporated (IAI) using MITRE's PALMA software to create normalized relative impact scores for each of these relationships. However, PALMA processing obscures the natural network representation of the data. Any network analysis that might identify patterns of interaction among data sources, products, and SBAs is therefore impossible. Collaborating with IAI, we cleaned and recreated a network from the original dataset. Using R and Python we explore the underlying structure of the network and apply frequent itemset mining algorithms to identify groups of data sources and products that interact. We reveal interesting patterns and relationships in the EOA dataset that were not immediately observable from the EOA 2016 report and provide a basis for further exploration of the EOA network dataset.

Engineering design in the primary school: applying stem concepts to build an optical instrument

NASA Astrophysics Data System (ADS)

King, Donna; English, Lyn D.

2016-12-01

Internationally there is a need for research that focuses on STEM (Science, Technology, Engineering and Mathematics) education to equip students with the skills needed for a rapidly changing future. One way to do this is through designing engineering activities that reflect real-world problems and contextualise students' learning of STEM concepts. As such, this study examined the learning that occurred when fifth-grade students completed an optical engineering activity using an iterative engineering design model. Through a qualitative methodology using a case study design, we analysed multiple data sources including students' design sketches from eight focus groups. Three key findings emerged: first, the collaborative process of the first design sketch enabled students to apply core STEM concepts to model construction; second, during the construction stage students used experimentation for the positioning of lenses, mirrors and tubes resulting in a simpler 'working' model; and third, the redesign process enabled students to apply structural changes to their design. The engineering design model was useful for structuring stages of design, construction and redesign; however, we suggest a more flexible approach for advanced applications of STEM concepts in the future.

Designing Extensible Data Management for Ocean Observatories, Platforms, and Devices

NASA Astrophysics Data System (ADS)

Graybeal, J.; Gomes, K.; McCann, M.; Schlining, B.; Schramm, R.; Wilkin, D.

2002-12-01

The Monterey Bay Aquarium Research Institute (MBARI) has been collecting science data for 15 years from all kinds of oceanographic instruments and systems, and is building a next-generation observing system, the MBARI Ocean Observing System (MOOS). To meet the data management requirements of the MOOS, the Institute began developing a flexible, extensible data management solution, the Shore Side Data System (SSDS). This data management system must address a wide variety of oceanographic instruments and data sources, including instruments and platforms of the future. Our data management solution will address all elements of the data management challenge, from ingest (including suitable pre-definition of metadata) through to access and visualization. Key to its success will be ease of use, and automatic incorporation of new data streams and data sets. The data will be of many different forms, and come from many different types of instruments. Instruments will be designed for fixed locations (as with moorings), changing locations (drifters and AUVs), and cruise-based sampling. Data from airplanes, satellites, models, and external archives must also be considered. Providing an architecture which allows data from these varied sources to be automatically archived and processed, yet readily accessed, is only possible with the best practices in metadata definition, software design, and re-use of third-party components. The current status of SSDS development will be presented, including lessons learned from our science users and from previous data management designs.

Co-designing the next generation of home energy management systems with lead-users.

PubMed

Peacock, Andrew D; Chaney, Joel; Goldbach, Kristin; Walker, Guy; Tuohy, Paul; Santonja, Salvador; Todoli, David; Owens, Edward H

2017-04-01

Home energy management systems are widely promoted as essential components of future low carbon economies. It is argued in this paper that assumptions surrounding their deployment, and the methods used to design them, emerge from discredited models of people and energy. This offers an explanation for why their field trial performance is so inconsistent. A first of a kind field trial is reported. Three eco communities took part in a comprehensive participatory design exercise as lead users. The challenge was to help users synchronise their energy use behaviours with the availability of locally generated renewable energy sources. To meet this aim, a set of highly novel Home Energy Management interfaces were co-designed and tested. Not only were the designs radically different to the norm, but they also yielded sustained user engagement over a six-month follow-up period. It is argued that user-centred design holds the key to unlocking the energy saving potential of new domestic technologies, and this study represents a bold step in that direction. Copyright © 2016 Elsevier Ltd. All rights reserved.

Optimum Design of a Helicopter Rotor for Low Vibration Using Aeroelastic Analysis and Response Surface Methods

NASA Astrophysics Data System (ADS)

Ganguli, R.

2002-11-01

An aeroelastic analysis based on finite elements in space and time is used to model the helicopter rotor in forward flight. The rotor blade is represented as an elastic cantilever beam undergoing flap and lag bending, elastic torsion and axial deformations. The objective of the improved design is to reduce vibratory loads at the rotor hub that are the main source of helicopter vibration. Constraints are imposed on aeroelastic stability, and move limits are imposed on the blade elastic stiffness design variables. Using the aeroelastic analysis, response surface approximations are constructed for the objective function (vibratory hub loads). It is found that second order polynomial response surfaces constructed using the central composite design of the theory of design of experiments adequately represents the aeroelastic model in the vicinity of the baseline design. Optimization results show a reduction in the objective function of about 30 per cent. A key accomplishment of this paper is the decoupling of the analysis problem and the optimization problems using response surface methods, which should encourage the use of optimization methods by the helicopter industry.

Engineering radical polymer electrodes for electrochemical energy storage

NASA Astrophysics Data System (ADS)

Nevers, Douglas R.; Brushett, Fikile R.; Wheeler, Dean R.

2017-06-01

In principle a wide range of organic materials can store energy in the form of reversible redox conversions of stable radicals. Such chemistry holds great promise for energy storage applications due to high theoretical capacities, high rate capabilities, intrinsic structural tunability, and the possibility of low-cost "green" syntheses from renewable sources. There have been steady improvements in the design of organic radical polymers, in which radicals are incorporated into the backbone and/or as pendant groups. This review highlights opportunities for improved redox molecule and polymer design along with the key challenges (e.g., transport phenomena, solubility, and reaction mechanisms) to transitioning known organic radicals into high-performance electrodes. Ultimately, organic-based batteries are still a nascent field with many open questions. Further advances in molecular design, electrode engineering, and device architecture will be required for these systems to reach their full potential and meet the diverse and increasing demands for energy storage.

Design of electric control system for automatic vegetable bundling machine

NASA Astrophysics Data System (ADS)

Bao, Yan

2017-06-01

A design can meet the requirements of automatic bale food structure and has the advantages of simple circuit, and the volume is easy to enhance the electric control system of machine carrying bunch of dishes and low cost. The bundle of vegetable machine should meet the sensor to detect and control, in order to meet the control requirements; binding force can be adjusted by the button to achieve; strapping speed also can be adjusted, by the keys to set; sensors and mechanical line connection, convenient operation; can be directly connected with the plug, the 220V power supply can be connected to a power source; if, can work, by the transmission signal sensor, MCU to control the motor, drive and control procedures for small motor. The working principle of LED control circuit and temperature control circuit is described. The design of electric control system of automatic dish machine.

Compression of high-density 0.16 pC electron bunches through high field gradients for ultrafast single shot electron diffraction: The Compact RF Gun

PubMed Central

Daoud, Hazem; Floettmann, Klaus; Dwayne Miller, R. J.

2017-01-01

We present an RF gun design for single shot ultrafast electron diffraction experiments that can produce sub-100 fs high-charge electron bunches in the 130 keV energy range. Our simulations show that our proposed half-cell RF cavity is capable of producing 137 keV, 27 fs rms (60 fs FWHM), 106 electron bunches with an rms spot size of 276 μm and a transverse coherence length of 2.0 nm. The required operation power is 9.2 kW, significantly lower than conventional rf cavity designs and a key design feature. This electron source further relies on high electric field gradients at the cathode to simultaneously accelerate and compress the electron bunch to open up new space-time resolution domains for atomically resolved dynamics. PMID:28428973

Construction and Application of a Terahertz Scanning Near-Field Microscope for Study of Correlated Electron Materials at Cryogenic Temperatures and Nanometer Length Scales

NASA Astrophysics Data System (ADS)

Stinson, Harry Theodore, III

This dissertation describes the design and construction of the world's first cryogenic apertureless near-field microscope designed for terahertz sources and detectors. I first provide motivation for the creation of this instrument in the context of spectroscopy of correlated electron materials, and background information on the two techniques that the instrument combines, scanning near-field optical microscopy and terahertz time-domain spectroscopy. I then detail key components of the instrument design, including proof-of-principle results obtained at room and cryogenic temperatures. Following this, I discuss an imaging experiment performed with this instrument on vanadium dioxide, an insulator-metal transition material, which sheds new light on the nature of the phase transition and provides support for a new model Hamiltonian for the system. Finally, I discuss a theoretical proposal for the study of cuprate superconductors using this instrument.

Opto-mechanical door locking system

NASA Astrophysics Data System (ADS)

Patil, Saurabh S.; Rodrigues, Vanessa M.; Patil, Ajeetkumar; Chidangil, Santhosh

2015-09-01

We present an Opto-mechanical Door Locking System which is an optical system that combines a simple combination of a coherent light source (Laser) and a photodiode based sensor with focus toward security applications. The basic construct of the KEY comprises a Laser source in a cylindrical enclosure that slides perfectly into the LOCK. The Laser is pulsed at a fixed encrypted frequency unique to that locking system. Transistor-transistor logic (TTL) circuitry is used to achieve encryption. The casing of the key is designed in such a way that it will power the pulsing laser only when the key is inserted in the slot provided for it. The Lock includes a photo-sensor that will convert the detected light intensity to a corresponding electrical signal by decrypting the frequency. The lock also consists of a circuit with a feedback system that will carry the digital information regarding the encryption frequency code. The information received from the sensor is matched with the stored code; if found a perfect match, a signal will be sent to the servo to unlock the mechanical lock or to carry out any other operation. This technique can be incorporated in security systems for residences and safe houses, and can easily replace all conventional locks which formerly used fixed patterns to unlock. The major advantage of this proposed optomechanical system over conventional ones is that it no longer relies on a solid/imprinted pattern to perform its task and hence makes it almost impossible to tamper with.

Evaluating the Use of Existing Data Sources, Probabilistic Linkage, and Multiple Imputation to Build Population-based Injury Databases Across Phases of Trauma Care

PubMed Central

Newgard, Craig; Malveau, Susan; Staudenmayer, Kristan; Wang, N. Ewen; Hsia, Renee Y.; Mann, N. Clay; Holmes, James F.; Kuppermann, Nathan; Haukoos, Jason S.; Bulger, Eileen M.; Dai, Mengtao; Cook, Lawrence J.

2012-01-01

Objectives The objective was to evaluate the process of using existing data sources, probabilistic linkage, and multiple imputation to create large population-based injury databases matched to outcomes. Methods This was a retrospective cohort study of injured children and adults transported by 94 emergency medical systems (EMS) agencies to 122 hospitals in seven regions of the western United States over a 36-month period (2006 to 2008). All injured patients evaluated by EMS personnel within specific geographic catchment areas were included, regardless of field disposition or outcome. The authors performed probabilistic linkage of EMS records to four hospital and postdischarge data sources (emergency department [ED] data, patient discharge data, trauma registries, and vital statistics files) and then handled missing values using multiple imputation. The authors compare and evaluate matched records, match rates (proportion of matches among eligible patients), and injury outcomes within and across sites. Results There were 381,719 injured patients evaluated by EMS personnel in the seven regions. Among transported patients, match rates ranged from 14.9% to 87.5% and were directly affected by the availability of hospital data sources and proportion of missing values for key linkage variables. For vital statistics records (1-year mortality), estimated match rates ranged from 88.0% to 98.7%. Use of multiple imputation (compared to complete case analysis) reduced bias for injury outcomes, although sample size, percentage missing, type of variable, and combined-site versus single-site imputation models all affected the resulting estimates and variance. Conclusions This project demonstrates the feasibility and describes the process of constructing population-based injury databases across multiple phases of care using existing data sources and commonly available analytic methods. Attention to key linkage variables and decisions for handling missing values can be used to increase match rates between data sources, minimize bias, and preserve sampling design. PMID:22506952

Perceived barriers to the regionalization of adult critical care in the United States: a qualitative preliminary study

PubMed Central

Kahn, Jeremy M; Asch, Rebecca J; Iwashyna, Theodore J; Rubenfeld, Gordon D; Angus, Derek C; Asch, David A

2008-01-01

Background Regionalization of adult critical care services may improve outcomes for critically ill patients. We sought to develop a framework for understanding clinician attitudes toward regionalization and potential barriers to developing a tiered, regionalized system of care in the United States. Methods We performed a qualitative study using semi-structured interviews of critical care stakeholders in the United States, including physicians, nurses and hospital administrators. Stakeholders were identified from a stratified-random sample of United States general medical and surgical hospitals. Key barriers and potential solutions were identified by performing content analysis of the interview transcriptions. Results We interviewed 30 stakeholders from 24 different hospitals, representing a broad range of hospital locations and sizes. Key barriers to regionalization included personal and economic strain on families, loss of autonomy on the part of referring physicians and hospitals, loss of revenue on the part of referring physicians and hospitals, the potential to worsen outcomes at small hospitals by limiting services, and the potential to overwhelm large hospitals. Improving communication between destination and source hospitals, provider education, instituting voluntary objective criteria to become a designated referral center, and mechanisms to feed back patients and revenue to source hospitals were identified as potential solutions to some of these barriers. Conclusion Regionalization efforts will be met with significant conceptual and structural barriers. These data provide a foundation for future research and can be used to inform policy decisions regarding the design and implementation of a regionalized system of critical care. PMID:19014704

Concept of DT fuel cycle for a fusion neutron source

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anan'ev, S.; Spitsyn, A.V.; Kuteev, B.V.

2015-03-15

A concept of DT-fusion neutron source (FNS) with the neutron yield higher than 10{sup 18} neutrons per second is under design in Russia. Such a FNS is of interest for many applications: 1) basic and applied research (neutron scattering, etc); 2) testing the structural materials for fusion reactors; 3) control of sub-critical nuclear systems and 4) nuclear waste processing (including transmutation of minor actinides). This paper describes the fuel cycle concept of a compact fusion neutron source based on a small spherical tokamak (FNS-ST) with a MW range of DT fusion power and considers the key physics issues of thismore » device. The major and minor radii are ∼0.5 and ∼0.3 m, magnetic field ∼1.5 T, heating power less than 15 MW and plasma current 1-2 MA. The system provides the fuel mixture with equal fractions of D and T (D:T = 1:1) for all FNS technology systems. (authors)« less

Pulsed-DC DBD Plasma Actuators

NASA Astrophysics Data System (ADS)

Duong, Alan; Corke, Thomas; Thomas, Flint

2017-11-01

A power system for dielectric barrier discharge (DBD) plasma actuators that utilizes a pulsed-DC waveform is presented. The plasma actuator arrangement is identical to most typical AC-DBD designs with staggered electrodes that are separated by a dielectric insulator. A key difference is that the pulsed-DC actuator utilizes a DC voltage source to drive the actuator instead of an AC voltage input. The DC source is supplied to both electrodes. The exposed electrode remains constant in time while the encapsulated electrode is periodically grounded for short instances then is allowed to rise to the source DC level. Further investigation of the pulsed-DC plasma actuator was conducted. Time-resolved velocity measurements were done to characterize the induced velocity field generated by the pulsed-DC plasma actuator. A model of the pulsed-DC plasma actuator is developed in LTspice for further study. The work presented are intended in developing a model to be used in CFD flow control simulations. NASA SBIR NNX14CC12C.

Fast optical source for quantum key distribution based on semiconductor optical amplifiers.

PubMed

Jofre, M; Gardelein, A; Anzolin, G; Amaya, W; Capmany, J; Ursin, R; Peñate, L; Lopez, D; San Juan, J L; Carrasco, J A; Garcia, F; Torcal-Milla, F J; Sanchez-Brea, L M; Bernabeu, E; Perdigues, J M; Jennewein, T; Torres, J P; Mitchell, M W; Pruneri, V

2011-02-28

A novel integrated optical source capable of emitting faint pulses with different polarization states and with different intensity levels at 100 MHz has been developed. The source relies on a single laser diode followed by four semiconductor optical amplifiers and thin film polarizers, connected through a fiber network. The use of a single laser ensures high level of indistinguishability in time and spectrum of the pulses for the four different polarizations and three different levels of intensity. The applicability of the source is demonstrated in the lab through a free space quantum key distribution experiment which makes use of the decoy state BB84 protocol. We achieved a lower bound secure key rate of the order of 3.64 Mbps and a quantum bit error ratio as low as 1.14×10⁻² while the lower bound secure key rate became 187 bps for an equivalent attenuation of 35 dB. To our knowledge, this is the fastest polarization encoded QKD system which has been reported so far. The performance, reduced size, low power consumption and the fact that the components used can be space qualified make the source particularly suitable for secure satellite communication.

A Cabin Air Separator for EVA Oxygen

NASA Technical Reports Server (NTRS)

Graf, John C.

2011-01-01

Presently, the Extra-Vehicular Activities (EVAs) conducted from the Quest Joint Airlock on the International Space Station use high pressure, high purity oxygen that is delivered to the Space Station by the Space Shuttle. When the Space Shuttle retires, a new method of delivering high pressure, high purity oxygen to the High Pressure Gas Tanks (HPGTs) is needed. One method is to use a cabin air separator to sweep oxygen from the cabin air, generate a low pressure/high purity oxygen stream, and compress the oxygen with a multistage mechanical compressor. A main advantage to this type of system is that the existing low pressure oxygen supply infrastructure can be used as the source of cabin oxygen. ISS has two water electrolysis systems that deliver low pressure oxygen to the cabin, as well as chlorate candles and compressed gas tanks on cargo vehicles. Each of these systems can feed low pressure oxygen into the cabin, and any low pressure oxygen source can be used as an on-board source of oxygen. Three different oxygen separator systems were evaluated, and a two stage Pressure Swing Adsorption system was selected for reasons of technical maturity. Two different compressor designs were subjected to long term testing, and the compressor with better life performance and more favorable oxygen safety characteristics was selected. These technologies have been used as the basis of a design for a flight system located in Equipment Lock, and taken to Preliminary Design Review level of maturity. This paper describes the Cabin Air Separator for EVA Oxygen (CASEO) concept, describes the separator and compressor technology trades, highlights key technology risks, and describes the flight hardware concept as presented at Preliminary Design Review (PDR)

Free-Space Quantum Key Distribution with a High Generation Rate KTP Waveguide Photon-Pair Source

NASA Technical Reports Server (NTRS)

Wilson, J.; Chaffee, D.; Wilson, N.; Lekki, J.; Tokars, R.; Pouch, J.; Lind, A.; Cavin, J.; Helmick, S.; Roberts, T.;

LabKey Server NAb: A tool for analyzing, visualizing and sharing results from neutralizing antibody assays

PubMed Central

2011-01-01

Background Multiple types of assays allow sensitive detection of virus-specific neutralizing antibodies. For example, the extent of antibody neutralization of HIV-1, SIV and SHIV can be measured in the TZM-bl cell line through the degree of luciferase reporter gene expression after infection. In the past, neutralization curves and titers for this standard assay have been calculated using an Excel macro. Updating all instances of such a macro with new techniques can be unwieldy and introduce non-uniformity across multi-lab teams. Using Excel also poses challenges in centrally storing, sharing and associating raw data files and results. Results We present LabKey Server's NAb tool for organizing, analyzing and securely sharing data, files and results for neutralizing antibody (NAb) assays, including the luciferase-based TZM-bl NAb assay. The customizable tool supports high-throughput experiments and includes a graphical plate template designer, allowing researchers to quickly adapt calculations to new plate layouts. The tool calculates the percent neutralization for each serum dilution based on luminescence measurements, fits a range of neutralization curves to titration results and uses these curves to estimate the neutralizing antibody titers for benchmark dilutions. Results, curve visualizations and raw data files are stored in a database and shared through a secure, web-based interface. NAb results can be integrated with other data sources based on sample identifiers. It is simple to make results public after publication by updating folder security settings. Conclusions Standardized tools for analyzing, archiving and sharing assay results can improve the reproducibility, comparability and reliability of results obtained across many labs. LabKey Server and its NAb tool are freely available as open source software at http://www.labkey.com under the Apache 2.0 license. Many members of the HIV research community can also access the LabKey Server NAb tool without installing the software by using the Atlas Science Portal (https://atlas.scharp.org). Atlas is an installation of LabKey Server. PMID:21619655

Long-distance practical quantum key distribution by entanglement swapping.

PubMed

Scherer, Artur; Sanders, Barry C; Tittel, Wolfgang

2011-02-14

We develop a model for practical, entanglement-based long-distance quantum key distribution employing entanglement swapping as a key building block. Relying only on existing off-the-shelf technology, we show how to optimize resources so as to maximize secret key distribution rates. The tools comprise lossy transmission links, such as telecom optical fibers or free space, parametric down-conversion sources of entangled photon pairs, and threshold detectors that are inefficient and have dark counts. Our analysis provides the optimal trade-off between detector efficiency and dark counts, which are usually competing, as well as the optimal source brightness that maximizes the secret key rate for specified distances (i.e. loss) between sender and receiver.

Value-based management of design reuse

NASA Astrophysics Data System (ADS)

Carballo, Juan Antonio; Cohn, David L.; Belluomini, Wendy; Montoye, Robert K.

2003-06-01

Effective design reuse in electronic products has the potential to provide very large cost savings, substantial time-to-market reduction, and extra sources of revenue. Unfortunately, critical reuse opportunities are often missed because, although they provide clear value to the corporation, they may not benefit the business performance of an internal organization. It is therefore crucial to provide tools to help reuse partners participate in a reuse transaction when the transaction provides value to the corporation as a whole. Value-based Reuse Management (VRM) addresses this challenge by (a) ensuring that all parties can quickly assess the business performance impact of a reuse opportunity, and (b) encouraging high-value reuse opportunities by supplying value-based rewards to potential parties. In this paper we introduce the Value-Based Reuse Management approach and we describe key results on electronic designs that demonstrate its advantages. Our results indicate that Value-Based Reuse Management has the potential to significantly increase the success probability of high-value electronic design reuse.

Design for a spin-Seebeck diode based on two-dimensional materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fu, Hua-Hua; Wu, Dan-Dan; Gu, Lei

2015-07-01

Studies of the spin-Seebeck effect (SSE) are very important for the development of fundamental science and novel low-power-consumption technologies. The spin-Seebeck diode (SSD), in which the spin current can be driven by a forward temperature gradient but not by a reverse temperature gradient, is a key unit in spin caloritronic devices. Here, we propose a SSD design using two-dimensional (2D) materials such as silicene and phosphorene nanoribbons as the source and drain. Due to their unique band structures and magnetic states, thermally driven spin-up and spin-down currents flow in opposite directions. This mechanism is different from that of the previousmore » one, which uses two permalloy circular disks [Phys. Rev. Lett. 112, 047203 (2014)], and the SSD in our design can be easily integrated with gate voltage control. Since the concept of this design is rather general and applicable to many 2D materials, it is promising for the realization and exploitation of SSDs in nanodevices.« less

Flexible planar microfluidic chip employing a light emitting diode and a PIN-photodiode for portable flow cytometers.

PubMed

Kettlitz, Siegfried W; Valouch, Sebastian; Sittel, Wiebke; Lemmer, Uli

2012-01-07

Detection of fluorescence particles is a key method of flow cytometry. We evaluate the performance of a design for a microfluidic fluorescence particle detection device. Due to the planar design with low layer thicknesses, we avoid optical components such as lenses or dichroic mirrors and substitute them with a shadow mask and colored film filters. A commercially available LED is used as the light source and a PIN-photodiode as detector. This design approach reduces component cost and power consumption and enables supplying the device with power from a standard USB port. From evaluation of this design, we obtain a maximum particle detection frequency of up to 600 particles per second at a sensitivity of better than 4.7 × 10(5) MESF (molecules of equivalent soluble fluorochrome) measured with particles for FITC sensitivity calibration. Lowering the flow rate increases the instrument sensitivity by an order of magnitude enabling the detection of particles with 4.5 × 10(4) MESF.

Progress on development of SPIDER diagnostics

NASA Astrophysics Data System (ADS)

Pasqualotto, R.; Agostini, M.; Barbisan, M.; Bernardi, M.; Brombin, M.; Cavazzana, R.; Croci, G.; Palma, M. Dalla; Delogu, R. S.; Gorini, G.; Lotto, L.; Muraro, A.; Peruzzo, S.; Pimazzoni, A.; Pomaro, N.; Rizzolo, A.; Serianni, G.; Spolaore, M.; Tardocchi, M.; Zaniol, B.; Zaupa, M.

2017-08-01

SPIDER experiment, the full size prototype of the beam source for the ITER heating neutral beam injector, has to demonstrate extraction and acceleration to 100 kV of a large negative ion hydrogen or deuterium beam with co-extracted electron fraction e-/D- <1 and beam uniformity within 10%, for up to one hour beam pulses. Main RF source plasma and beam parameters are measured with different complementary techniques to exploit the combination of their specific features. While SPIDER plant systems are being installed, the different diagnostic systems are in the procurement phase. Their final design is described here with a focus on some key solutions and most original and cost effective implementations. Thermocouples used to measure the power load distribution in the source and over the beam dump front surface will be efficiently fixed with proven technique and acquired through commercial and custom electronics. Spectroscopy needs to use well collimated lines of sight and will employ novel design spectrometers with higher efficiency and resolution and filtered detectors with custom built amplifiers. The electrostatic probes will be operated through electronics specifically developed to cope with the challenging environment of the RF source. The instrumented calorimeter STRIKE will use new CFC tiles, still under development. Two linear cameras, one built in house, have been tested as suitable for optical beam tomography. Some diagnostic components are off the shelf, others are custom developed: some of these are being prototyped or are under test before final production and installation, which will be completed before start of SPIDER operation.

Networks as systems.

PubMed

Best, Allan; Berland, Alex; Greenhalgh, Trisha; Bourgeault, Ivy L; Saul, Jessie E; Barker, Brittany

2018-03-19

Purpose The purpose of this paper is to present a case study of the World Health Organization's Global Healthcare Workforce Alliance (GHWA). Based on a commissioned evaluation of GHWA, it applies network theory and key concepts from systems thinking to explore network emergence, effectiveness, and evolution to over a ten-year period. The research was designed to provide high-level strategic guidance for further evolution of global governance in human resources for health (HRH). Design/methodology/approach Methods included a review of published literature on HRH governance and current practice in the field and an in-depth case study whose main data sources were relevant GHWA background documents and key informant interviews with GHWA leaders, staff, and stakeholders. Sampling was purposive and at a senior level, focusing on board members, executive directors, funders, and academics. Data were analyzed thematically with reference to systems theory and Shiffman's theory of network development. Findings Five key lessons emerged: effective management and leadership are critical; networks need to balance "tight" and "loose" approaches to their structure and processes; an active communication strategy is key to create and maintain support; the goals, priorities, and membership must be carefully focused; and the network needs to support shared measurement of progress on agreed-upon goals. Shiffman's middle-range network theory is a useful tool when guided by the principles of complex systems that illuminate dynamic situations and shifting interests as global alliances evolve. Research limitations/implications This study was implemented at the end of the ten-year funding cycle. A more continuous evaluation throughout the term would have provided richer understanding of issues. Experience and perspectives at the country level were not assessed. Practical implications Design and management of large, complex networks requires ongoing attention to key issues like leadership, and flexible structures and processes to accommodate the dynamic reality of these networks. Originality/value This case study builds on growing interest in the role of networks to foster large-scale change. The particular value rests on the longitudinal perspective on the evolution of a large, complex global network, and the use of theory to guide understanding.

Progress on the development of the next generation x-ray beam position monitors at the advanced photon source

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, S. H., E-mail: shlee@aps.anl.gov; Yang, B. X., E-mail: bxyang@aps.anl.gov; Decker, G., E-mail: decker@aps.anl.gov

Accurate and stable x-ray beam position monitors (XBPMs) are key elements in obtaining the desired user beam stability in the Advanced Photon Source (APS). The next generation XBPMs for high heat load front ends (HHL FEs) have been designed to meet these requirements by utilizing Cu K-edge x-ray fluorescence (XRF) from a pair of copper absorbers and have been installed at the front ends (FEs) of the APS. Commissioning data showed a significant performance improvement over the existing photoemission-based XBPMs. While a similar design concept can be applied for the canted undulator front ends, where two undulator beams are separatedmore » by 1.0-mrad, the lower beam power (< 10 kW) per undulator allows us to explore lower-cost solutions based on Compton scattering from the diamond blades placed edge-on to the x-ray beam. A prototype of the Compton scattering XBPM system was installed at 24-ID-A in May 2015. In this report, the design and test results for XRF-based XBPM and Compton scattering based XBPM are presented. Ongoing research related to the development of the next generation XBPMs on thermal contact resistance of a joint between two solid bodies is also discussed.« less

Design of a Long Endurance Titan VTOL Vehicle

NASA Technical Reports Server (NTRS)

Prakash, Ravi; Braun, Robert D.; Colby, Luke S.; Francis, Scott R.; Guenduez, Mustafa E.; Flaherty, Kevin W.; Lafleur, Jarret M.; Wright, Henry S.

2006-01-01

Saturn s moon Titan promises insight into many key scientific questions, many of which can be investigated only by in situ exploration of the surface and atmosphere of the moon. This research presents a vertical takeoff and landing (VTOL) vehicle designed to conduct a scientific investigation of Titan s atmosphere, clouds, haze, surface, and any possible oceans. In this investigation, multiple options for vertical takeoff and horizontal mobility were considered. A helicopter was baselined because of its many advantages over other types of vehicles, namely access to hazardous terrain and the ability to perform low speed aerial surveys. Using a nuclear power source and the atmosphere of Titan, a turbo expander cycle produces the 1.9 kW required by the vehicle for flight and operations, allowing it to sustain a long range, long duration mission that could traverse the majority of Titan. Such a power source could increase the lifespan and quality of science for planetary aerial flight to an extent that the limiting factor for the mission life is not available power but the life of the mechanical parts. Therefore, the mission could potentially last for years. This design is the first to investigate the implications of this potentially revolutionary technology on a Titan aerial vehicle.

A sensitivity analysis for missing outcomes due to truncation by death under the matched-pairs design.

PubMed

Imai, Kosuke; Jiang, Zhichao

2018-04-29

The matched-pairs design enables researchers to efficiently infer causal effects from randomized experiments. In this paper, we exploit the key feature of the matched-pairs design and develop a sensitivity analysis for missing outcomes due to truncation by death, in which the outcomes of interest (e.g., quality of life measures) are not even well defined for some units (e.g., deceased patients). Our key idea is that if 2 nearly identical observations are paired prior to the randomization of the treatment, the missingness of one unit's outcome is informative about the potential missingness of the other unit's outcome under an alternative treatment condition. We consider the average treatment effect among always-observed pairs (ATOP) whose units exhibit no missing outcome regardless of their treatment status. The naive estimator based on available pairs is unbiased for the ATOP if 2 units of the same pair are identical in terms of their missingness patterns. The proposed sensitivity analysis characterizes how the bounds of the ATOP widen as the degree of the within-pair similarity decreases. We further extend the methodology to the matched-pairs design in observational studies. Our simulation studies show that informative bounds can be obtained under some scenarios when the proportion of missing data is not too large. The proposed methodology is also applied to the randomized evaluation of the Mexican universal health insurance program. An open-source software package is available for implementing the proposed research. Copyright © 2018 John Wiley & Sons, Ltd.

Defining the best quality-control systems by design and inspection.

PubMed

Hinckley, C M

1997-05-01

Not all of the many approaches to quality control are equally effective. Nonconformities in laboratory testing are caused basically by excessive process variation and mistakes. Statistical quality control can effectively control process variation, but it cannot detect or prevent most mistakes. Because mistakes or blunders are frequently the dominant source of nonconformities, we conclude that statistical quality control by itself is not effective. I explore the 100% inspection methods essential for controlling mistakes. Unlike the inspection techniques that Deming described as ineffective, the new "source" inspection methods can detect mistakes and enable corrections before nonconformities are generated, achieving the highest degree of quality at a fraction of the cost of traditional methods. Key relationships between task complexity and nonconformity rates are also described, along with cultural changes that are essential for implementing the best quality-control practices.

Emittance preservation during bunch compression with a magnetized beam

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stratakis, Diktys

2015-09-02

The deleterious effects of coherent synchrotron radiation (CSR) on the phase-space and energy spread of high-energy beams in accelerator light sources can significantly constrain the machine design and performance. In this paper, we present a simple method to preserve the beam emittance by means of using magnetized beams that exhibit a large aspect ratio on their transverse dimensions. The concept is based on combining a finite solenoid field where the beam is generated together with a special optics adapter. Numerical simulations of this new type of beam source show that the induced phase-space density growth can be notably suppressed tomore » less than 1% for any bunch charge. This work elucidates the key parameters that are needed for emittance preservation, such as the required field and aspect ratio for a given bunch charge.« less

Radioisotope thermal photovoltaic application of the GaSb solar cell

NASA Technical Reports Server (NTRS)

Morgan, M. D.; Horne, W. E.; Day, A. C.

1991-01-01

An examination of a RTVP (radioisotopic thermophotovoltaic) conceptual design has shown a high potential for power densities well above those achievable with radioisotopic thermoelectric generator (RTG) systems. An efficiency of 14.4 percent and system specific power of 9.25 watts/kg were predicted for a system with sixteen GPHS (general purpose heat source) sources operating at 1100 C. The models also showed a 500 watt system power by the strontium-90 isotope at 1200 C at an efficiency of 17.0 percent and a system specific power of 11.8 watts/kg. The key to this level of performance is a high-quality photovoltaic cell with narrow bandgap and a reflective rear contact. Recent work at Boeing on GaSb cells and transparent back GaAs cells indicate that such a cell is well within reach.

Vertical pillar nanoantenna for emission enhancement and redirection

NASA Astrophysics Data System (ADS)

Paparone, J.; Laverdant, J.; Brucoli, G.; Symonds, C.; Crut, A.; Del Fatti, N.; Benoit, J. M.; Bellessa, J.

2018-01-01

Designing efficient metallic nanostructures can help in realizing bright single photon emission in the visible and near-infrared ranges. We propose a novel nanostructure design that combines the benefits of plasmonic hot spot generation in the near-field and the concept of antennas developed in the radio-frequency range. The antenna is formed by a vertical stack of metallic and dielectric nanocylinders. When used for controlling the far-field emission of a localized source, its key features are moderate losses in the metal, relatively large Purcell factors, as well as a low sensibility to the lateral position of the emitter. A redirection process necessary for these vertical structures is proposed, based on the versatility of the vertical geometry, and allows an efficient redirection of the emitted light even for antennas on dielectric substrates.

A New Design of the Test Rig to Measure the Transmission Error of Automobile Gearbox

NASA Astrophysics Data System (ADS)

Hou, Yixuan; Zhou, Xiaoqin; He, Xiuzhi; Liu, Zufei; Liu, Qiang

2017-12-01

Noise and vibration affect the performance of automobile gearbox. And transmission error has been regarded as an important excitation source in gear system. Most of current research is focused on the measurement and analysis of single gear drive, and few investigations on the transmission error measurement in complete gearbox were conducted. In order to measure transmission error in a complete automobile gearbox, a kind of electrically closed test rig is developed. Based on the principle of modular design, the test rig can be used to test different types of gearbox by adding necessary modules. The test rig for front engine, rear-wheel-drive gearbox is constructed. And static and modal analysis methods are taken to verify the performance of a key component.

Preamplifiers for non-contact capacitive biopotential measurements.

PubMed

Peng, GuoChen; Ignjatovic, Zeljko; Bocko, Mark F

2013-01-01

Non-contact biopotential sensing is an attractive measurement strategy for a number of health monitoring applications, primarily the ECG and the EEG. In all such applications a key technical challenge is the design of a low-noise trans-impedance preamplifier for the typically low-capacitance, high source impedance sensing electrodes. In this paper, we compare voltage and charge amplifier designs in terms of their common mode rejection ratio, noise performance, and frequency response. Both amplifier types employ the same operational-transconductance amplifier (OTA), which was fabricated in a 0.35 um CMOS process. The results show that a charge amplifier configuration has advantages for small electrode-to-subject coupling capacitance values (less than 10 pF--typical of noncontact electrodes) and that the voltage amplifier configuration has advantages for electrode capacitances above 10 pF.

Revitalization of Energy Supply Systems in the Scale of a Town, a District and an Island

NASA Astrophysics Data System (ADS)

Juchimiuk, Justyna

2016-09-01

Model actions undertaken in HafenCity and Wilhelmsburg during IBA Hamburg 2006- 13 as well as energy transformation of Danish island of Samsø towards self-sufficiency are examples of the use of energy as one of the key factors in the design of revitalization process in various scales. An important issue is to determine the impact of renewable energy systems on design process, architecture and urbanism of revitalized structures. Article examines the programs and projects related to the processes: renewal of degraded inner-industrial areas (brownfields), ecological restoration of degraded land, the revitalization of port and underdeveloped areas in the aspects of climate protection, the use of energy from renewable sources and improvement of technical conditions of building substance while maintaining the principles of sustainable development.

Concept design of a time-of-flight spectrometer for the measurement of the energy of alpha particles.

PubMed

García-Toraño, E

2018-04-01

The knowledge of the energies of the alpha particles emitted in the radioactive decay of a nuclide is a key factor in the construction of its decay scheme. Virtually all existing data are based on a few absolute measurements made by magnetic spectrometry (MS), to which most other MS measurements are traced. An alternative solution would be the use of time-of-flight detectors. This paper discusses the main aspects to be considered in the design of such detectors, and the performances that could be reasonably expected. Based on the concepts discussed here, it is estimated that an energy resolution about 2.5keV may be attainable with a good quality source. Copyright © 2017 Elsevier Ltd. All rights reserved.

FermiLib v0.1

DOE Office of Scientific and Technical Information (OSTI.GOV)

MCCLEAN, JARROD; HANER, THOMAS; STEIGER, DAMIAN

FermiLib is an open source software package designed to facilitate the development and testing of algorithms for simulations of fermionic systems on quantum computers. Fermionic simulations represent an important application of early quantum devices with a lot of potential high value targets, such as quantum chemistry for the development of new catalysts. This software strives to provide a link between the required domain expertise in specific fermionic applications and quantum computing to enable more users to directly interface with, and develop for, these applications. It is an extensible Python library designed to interface with the high performance quantum simulator, ProjectQ,more » as well as application specific software such as PSI4 from the domain of quantum chemistry. Such software is key to enabling effective user facilities in quantum computation research.« less

A Buddhist perspective on industrial engineering and the design of work.

PubMed

Lee, Wei-Tau; Blumenthal, James A; Funk, Kenneth H

2014-06-01

The modern way of life is highly dependent upon the production of goods by industrial organizations that are in turn dependent upon their workers for their ongoing operations. Even though more than a century has passed since the dawn of the industrial revolution, many dangerous aspects of work, both physical and mental, remain in the workplace today. Using Buddhist philosophical principles, this paper suggests that although many sources of the problem reside within the larger society, the industrial engineer is still a key factor in bettering work and providing a workplace suitable for their fellow workers. Drawing on these insights, we present a number of work design guidelines that industrial engineers who abide by Buddhist principles could practice to help overcome some of the many sufferings produced by modern work.

Measuring competition in health care markets.

PubMed Central

Baker, L C

2001-01-01

OBJECTIVE: Measuring competition is increasingly important for analysis of health care markets and policies. Measurement of competition in health care is made complex by the breadth of potential issues under study, by the lack of necessary data, and by rapid changes in health care financing and delivery. This study reviews key issues in the measurement of competition and is designed to familiarize researchers and policymakers interested in competition measurement, but not steeped in its practice, with key concepts, data sources, and ways of adapting measures to fit ongoing changes in health care markets. PRINCIPAL FINDINGS: Attention to several key issues will strengthen measurement. Important components of successful measurement are: careful identification of the products and market areas for study; selection of Herfindahl-Hirschman or other indices to fit the issues being considered; consideration of econometric problems, like endogeneity, with common measures; and attention to the ways that current marketplace changes, like growth in managed care, affect the performance of classic measures. Data needed for constructing measures are also frequently scarce, insufficient, or both. Measurement could be improved with access to better data. PMID:11327175

Long distance measurement-device-independent quantum key distribution with entangled photon sources

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xu, Feihu; Qi, Bing; Liao, Zhongfa

2013-08-05

We present a feasible method that can make quantum key distribution (QKD), both ultra-long-distance and immune, to all attacks in the detection system. This method is called measurement-device-independent QKD (MDI-QKD) with entangled photon sources in the middle. By proposing a model and simulating a QKD experiment, we find that MDI-QKD with one entangled photon source can tolerate 77 dB loss (367 km standard fiber) in the asymptotic limit and 60 dB loss (286 km standard fiber) in the finite-key case with state-of-the-art detectors. Our general model can also be applied to other non-QKD experiments involving entanglement and Bell state measurements.

Measurement-device-independent entanglement-based quantum key distribution

NASA Astrophysics Data System (ADS)

Yang, Xiuqing; Wei, Kejin; Ma, Haiqiang; Sun, Shihai; Liu, Hongwei; Yin, Zhenqiang; Li, Zuohan; Lian, Shibin; Du, Yungang; Wu, Lingan

2016-05-01

We present a quantum key distribution protocol in a model in which the legitimate users gather statistics as in the measurement-device-independent entanglement witness to certify the sources and the measurement devices. We show that the task of measurement-device-independent quantum communication can be accomplished based on monogamy of entanglement, and it is fairly loss tolerate including source and detector flaws. We derive a tight bound for collective attacks on the Holevo information between the authorized parties and the eavesdropper. Then with this bound, the final secret key rate with the source flaws can be obtained. The results show that long-distance quantum cryptography over 144 km can be made secure using only standard threshold detectors.

Survey data on key climate and environmental drivers of farmers' migration in Burkina Faso, West Africa.

PubMed

Sanfo, Safiétou; Fonta, M William; Boubacar, Ibrahim; Lamers, P A John

2016-12-01

This article describes two datasets generated from various sources in south western Burkina Faso to identify the key climate and environmental drivers that cause farmers to migrate. The survey sampling is random but reasoned and rational. The first dataset from 367 farm households contains data on farmers' perception of climate change risks or hazards, their impacts on farmland productivity and farm households' risk management strategies. The second dataset from 58 farm households contains data on agricultural practices, environmental changes, and environmental migration. Three supplemental Excel sheets show the results of the surveys. Details on the sample as well as further interpretation and discussion of the surveys are available in the associated research article ('Field Facts for Crop Insurance Design: Empirical Evidence from South Western Burkina Faso' (W. M. Fonta, S. Sanfo, B. Ibrahim, B. Barry, 2015) [1]).

Microwave and continuous flow technologies in drug discovery.

PubMed

Sadler, Sara; Moeller, Alexander R; Jones, Graham B

2012-12-01

Microwave and continuous flow microreactors have become mainstream heating sources in contemporary pharmaceutical company laboratories. Such technologies will continue to benefit from design and engineering improvements, and now play a key role in the drug discovery process. The authors review the applications of flow- and microwave-mediated heating in library, combinatorial, solid-phase, metal-assisted, and protein chemistries. Additionally, the authors provide a description of the combination of microwave and continuous flow platforms, with applications in the preparation of radiopharmaceuticals and in drug candidate development. Literature reviewed is chiefly 2000 - 2012, plus key citations from earlier reports. With the advent of microwave irradiation, reactions that normally took days to complete can now be performed in a matter of minutes. Coupled with the introduction of continuous flow microreactors, pharmaceutical companies have an easy way to improve the greenness and efficiency of many synthetic operations. The combined force of these technologies offers the potential to revolutionize discovery and manufacturing processes.

Authentication Based on Non-Interactive Zero-Knowledge Proofs for the Internet of Things.

PubMed

Martín-Fernández, Francisco; Caballero-Gil, Pino; Caballero-Gil, Cándido

2016-01-07

This paper describes the design and analysis of a new scheme for the authenticated exchange of confidential information in insecure environments within the Internet of Things, which allows a receiver of a message to authenticate the sender and compute a secret key shared with it. The proposal is based on the concept of a non-interactive zero-knowledge proof, so that in a single communication, relevant data may be inferred to verify the legitimacy of the sender. Besides, the new scheme uses the idea under the Diffie-Hellman protocol for the establishment of a shared secret key. The proposal has been fully developed for platforms built on the Android Open Source Project, so it can be used in any device or sensor with this operating system. This work provides a performance study of the implementation and a comparison between its promising results and others obtained with similar schemes.

Authentication Based on Non-Interactive Zero-Knowledge Proofs for the Internet of Things

PubMed Central

Martín-Fernández, Francisco; Caballero-Gil, Pino; Caballero-Gil, Cándido

2016-01-01

This paper describes the design and analysis of a new scheme for the authenticated exchange of confidential information in insecure environments within the Internet of Things, which allows a receiver of a message to authenticate the sender and compute a secret key shared with it. The proposal is based on the concept of a non-interactive zero-knowledge proof, so that in a single communication, relevant data may be inferred to verify the legitimacy of the sender. Besides, the new scheme uses the idea under the Diffie–Hellman protocol for the establishment of a shared secret key. The proposal has been fully developed for platforms built on the Android Open Source Project, so it can be used in any device or sensor with this operating system. This work provides a performance study of the implementation and a comparison between its promising results and others obtained with similar schemes. PMID:26751454

Using Linked Electronic Health Records to Estimate Healthcare Costs: Key Challenges and Opportunities.

PubMed

Asaria, Miqdad; Grasic, Katja; Walker, Simon

2016-02-01

This paper discusses key challenges and opportunities that arise when using linked electronic health records (EHR) in health economics and outcomes research (HEOR), with a particular focus on estimating healthcare costs. These challenges and opportunities are framed in the context of a case study modelling the costs of stable coronary artery disease in England. The challenges and opportunities discussed fall broadly into the categories of (1) handling and organising data of this size and sensitivity; (2) extracting clinical endpoints from datasets that have not been designed and collected with such endpoints in mind; and (3) the principles and practice of costing resource use from routinely collected data. We find that there are a number of new challenges and opportunities that arise when working with EHR compared with more traditional sources of data for HEOR. These call for greater clinician involvement and intelligent use of sensitivity analysis.

Data Collection for Mental Health Studies Through Digital Platforms: Requirements and Design of a Prototype.

PubMed

Aledavood, Talayeh; Triana Hoyos, Ana Maria; Alakörkkö, Tuomas; Kaski, Kimmo; Saramäki, Jari; Isometsä, Erkki; Darst, Richard K

2017-06-09

Mental and behavioral disorders are the main cause of disability worldwide. However, their diagnosis is challenging due to a lack of reliable biomarkers; current detection is based on structured clinical interviews which can be biased by the patient's recall ability, affective state, changing in temporal frames, etc. While digital platforms have been introduced as a possible solution to this complex problem, there is little evidence on the extent of usability and usefulness of these platforms. Therefore, more studies where digital data is collected in larger scales are needed to collect scientific evidence on the capacities of these platforms. Most of the existing platforms for digital psychiatry studies are designed as monolithic systems for a certain type of study; publications from these studies focus on their results, rather than the design features of the data collection platform. Inevitably, more tools and platforms will emerge in the near future to fulfill the need for digital data collection for psychiatry. Currently little knowledge is available from existing digital platforms for future data collection platforms to build upon. The objective of this work was to identify the most important features for designing a digital platform for data collection for mental health studies, and to demonstrate a prototype platform that we built based on these design features. We worked closely in a multidisciplinary collaboration with psychiatrists, software developers, and data scientists and identified the key features which could guarantee short-term and long-term stability and usefulness of the platform from the designing stage to data collection and analysis of collected data. The key design features that we identified were flexibility of access control, flexibility of data sources, and first-order privacy protection. We also designed the prototype platform Non-Intrusive Individual Monitoring Architecture (Niima), where we implemented these key design features. We described why each of these features are important for digital data collection for psychiatry, gave examples of projects where Niima was used or is going to be used in the future, and demonstrated how incorporating these design principles opens new possibilities for studies. The new methods of digital psychiatry are still immature and need further research. The design features we suggested are a first step to design platforms which can adapt to the upcoming requirements of digital psychiatry. ©Talayeh Aledavood, Ana Maria Triana Hoyos, Tuomas Alakörkkö, Kimmo Kaski, Jari Saramäki, Erkki Isometsä, Richard K Darst. Originally published in JMIR Research Protocols (http://www.researchprotocols.org), 09.06.2017.

SolSTUS: Solar Source Thermal Upper Stage

NASA Astrophysics Data System (ADS)

This paper was written by members of the Utah State University (USU) Space Systems Design class, fall quarter 1993. The class is funded by NASA and administered by the University Space Research Association (USRA). The focus of the class is to give students some experience in design of space systems and as a source of original ideas for NASA. This paper is a summary of the work done by members of the Space Systems Design class during the opening phase of the course. The class was divided into groups to work on different areas of the Solar Thermal Rocket (STR) booster in order to produce a design reference mission that would identify the key design issues. The design reference mission focused upon a small satellite mission to Mars. There are several critical components in a Solar Thermal Rocket. STR's produce a very low thrust, but have a high specific impulse, meaning that they take longer to reach the desired orbit, but use a lot less fuel in doing it. The complexity of the rocket is discussed in this paper. Some of the more critical design problems discussed are: (1) the structural and optical complexity of collecting and focusing sunlight onto a specific point, (2) long term storage of fuel (liquid hydrogen), (3) attitude control while thrusting in an elliptical orbit and orienting the mirrors to collect sunlight, and (4) power and communications for the rocket and it's internal systems. The design reference mission discussed here is a very general mission to Mars. A first order trajectory design has been done and a possible basic science payload for Mars has been suggested. This paper summarizes the design reference mission (DRM) formulated by the USU students during fall quarter and identifies major design challenges that will confront the design team during the next two quarters here at USU.

SolSTUS: Solar Source Thermal Upper Stage

NASA Technical Reports Server (NTRS)

1994-01-01

This paper was written by members of the Utah State University (USU) Space Systems Design class, fall quarter 1993. The class is funded by NASA and administered by the University Space Research Association (USRA). The focus of the class is to give students some experience in design of space systems and as a source of original ideas for NASA. This paper is a summary of the work done by members of the Space Systems Design class during the opening phase of the course. The class was divided into groups to work on different areas of the Solar Thermal Rocket (STR) booster in order to produce a design reference mission that would identify the key design issues. The design reference mission focused upon a small satellite mission to Mars. There are several critical components in a Solar Thermal Rocket. STR's produce a very low thrust, but have a high specific impulse, meaning that they take longer to reach the desired orbit, but use a lot less fuel in doing it. The complexity of the rocket is discussed in this paper. Some of the more critical design problems discussed are: (1) the structural and optical complexity of collecting and focusing sunlight onto a specific point, (2) long term storage of fuel (liquid hydrogen), (3) attitude control while thrusting in an elliptical orbit and orienting the mirrors to collect sunlight, and (4) power and communications for the rocket and it's internal systems. The design reference mission discussed here is a very general mission to Mars. A first order trajectory design has been done and a possible basic science payload for Mars has been suggested. This paper summarizes the design reference mission (DRM) formulated by the USU students during fall quarter and identifies major design challenges that will confront the design team during the next two quarters here at USU.

Quantum key distribution with passive decoy state selection

NASA Astrophysics Data System (ADS)

Mauerer, Wolfgang; Silberhorn, Christine

2007-05-01

We propose a quantum key distribution scheme which closely matches the performance of a perfect single photon source. It nearly attains the physical upper bound in terms of key generation rate and maximally achievable distance. Our scheme relies on a practical setup based on a parametric downconversion source and present day, nonideal photon-number detection. Arbitrary experimental imperfections which lead to bit errors are included. We select decoy states by classical postprocessing. This allows one to improve the effective signal statistics and achievable distance.

SPOT 5/HRS: A Key Source for Navigation Database

DTIC Science & Technology

2003-09-02

SUBTITLE SPOT 5 / HRS: A Key Source for Navigation Database 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT ......strategic objective. Nice data ….. What after ?? Filière SPOT Marc BERNARD Page 15 Producing from HRS u Partnership with IGN ( French

Round-robin differential-phase-shift quantum key distribution with heralded pair-coherent sources

NASA Astrophysics Data System (ADS)

Wang, Le; Zhao, Shengmei

2017-04-01

Round-robin differential-phase-shift (RRDPS) quantum key distribution (QKD) scheme provides an effective way to overcome the signal disturbance from the transmission process. However, most RRDPS-QKD schemes use weak coherent pulses (WCPs) as the replacement of the perfect single-photon source. Considering the heralded pair-coherent source (HPCS) can efficiently remove the shortcomings of WCPs, we propose a RRDPS-QKD scheme with HPCS in this paper. Both infinite-intensity decoy-state method and practical three-intensity decoy-state method are adopted to discuss the tight bound of the key rate of the proposed scheme. The results show that HPCS is a better candidate for the replacement of the perfect single-photon source, and both the key rate and the transmission distance are greatly increased in comparison with those results with WCPs when the length of the pulse trains is small. Simultaneously, the performance of the proposed scheme using three-intensity decoy states is close to that result using infinite-intensity decoy states when the length of pulse trains is small.

Assessment of the Current Level of Automation in the Manufacture of Fuel Cell Systems for Combined Heat and Power Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ulsh, M.; Wheeler, D.; Protopappas, P.

The U.S. Department of Energy (DOE) is interested in supporting manufacturing research and development (R&D) for fuel cell systems in the 10-1,000 kilowatt (kW) power range relevant to stationary and distributed combined heat and power applications, with the intent to reduce manufacturing costs and increase production throughput. To assist in future decision-making, DOE requested that the National Renewable Energy Laboratory (NREL) provide a baseline understanding of the current levels of adoption of automation in manufacturing processes and flow, as well as of continuous processes. NREL identified and visited or interviewed key manufacturers, universities, and laboratories relevant to the study usingmore » a standard questionnaire. The questionnaire covered the current level of vertical integration, the importance of quality control developments for automation, the current level of automation and source of automation design, critical balance of plant issues, potential for continuous cell manufacturing, key manufacturing steps or processes that would benefit from DOE support for manufacturing R&D, the potential for cell or stack design changes to support automation, and the relationship between production volume and decisions on automation.« less

Time assignment system and its performance aboard the Hitomi satellite

NASA Astrophysics Data System (ADS)

Terada, Yukikatsu; Yamaguchi, Sunao; Sugimoto, Shigenobu; Inoue, Taku; Nakaya, Souhei; Murakami, Maika; Yabe, Seiya; Oshimizu, Kenya; Ogawa, Mina; Dotani, Tadayasu; Ishisaki, Yoshitaka; Mizushima, Kazuyo; Kominato, Takashi; Mine, Hiroaki; Hihara, Hiroki; Iwase, Kaori; Kouzu, Tomomi; Tashiro, Makoto S.; Natsukari, Chikara; Ozaki, Masanobu; Kokubun, Motohide; Takahashi, Tadayuki; Kawakami, Satoko; Kasahara, Masaru; Kumagai, Susumu; Angelini, Lorella; Witthoeft, Michael

2018-01-01

Fast timing capability in x-ray observation of astrophysical objects is one of the key properties for the ASTRO-H (Hitomi) mission. Absolute timing accuracies of 350 or 35 μs are required to achieve nominal scientific goals or to study fast variabilities of specific sources. The satellite carries a GPS receiver to obtain accurate time information, which is distributed from the central onboard computer through the large and complex SpaceWire network. The details of the time system on the hardware and software design are described. In the distribution of the time information, the propagation delays and jitters affect the timing accuracy. Six other items identified within the timing system will also contribute to absolute time error. These error items have been measured and checked on ground to ensure the time error budgets meet the mission requirements. The overall timing performance in combination with hardware performance, software algorithm, and the orbital determination accuracies, etc. under nominal conditions satisfies the mission requirements of 35 μs. This work demonstrates key points for space-use instruments in hardware and software designs and calibration measurements for fine timing accuracy on the order of microseconds for midsized satellites using the SpaceWire (IEEE1355) network.

A Wideband Satcom Based Avionics Network with CDMA Uplink and TDM Downlink

NASA Technical Reports Server (NTRS)

Agrawal, D.; Johnson, B. S.; Madhow, U.; Ramchandran, K.; Chun, K. S.

2000-01-01

The purpose of this paper is to describe some key technical ideas behind our vision of a future satcom based digital communication network for avionics applications The key features of our design are as follows: (a) Packetized transmission to permit efficient use of system resources for multimedia traffic; (b) A time division multiplexed (TDM) satellite downlink whose physical layer is designed to operate the satellite link at maximum power efficiency. We show how powerful turbo codes (invented originally for linear modulation) can be used with nonlinear constant envelope modulation, thus permitting the satellite amplifier to operate in a power efficient nonlinear regime; (c) A code division multiple access (CDMA) satellite uplink, which permits efficient access to the satellite from multiple asynchronous users. Closed loop power control is difficult for bursty packetized traffic, especially given the large round trip delay to the satellite. We show how adaptive interference suppression techniques can be used to deal with the ensuing near-far problem; (d) Joint source-channel coding techniques are required both at the physical and the data transport layer to optimize the end-to-end performance. We describe a novel approach to multiple description image encoding at the data transport layer in this paper.

Published intimate partner violence studies often differ from their trial registration records.

PubMed

Madden, Kim; Tai, Kerry; Ali, Zak; Schneider, Patricia; Singh, Mahip; Ghert, Michelle; Bhandari, Mohit

2017-12-27

Registering study protocols in a trial registry is important for methodologic transparency and reducing selective reporting bias. The objective of this investigation was to determine whether published studies of intimate partner violence (IPV) that had been registered matched the registration record on key study design elements. We systematically searched three trial registries to identify registered IPV studies and the published literature for the associated publication. Two authors independently determined for each study whether key study elements in the registry matched those in the published paper. We included 66 studies published between 2006 and 2017. Nearly half (29/66, 44%) were registered after study completion. Many (26/66, 39%) had discrepancies regarding the primary outcome, and nearly two-thirds (42/66, 64%) had discrepancies in secondary outcomes. Discrepancies in study design were less frequent (13/66, 20%). However, large changes in sample size (26/66, 39%) and discrepancies in funding source (28/66, 42%) were frequently observed. Trial registries are important tools for research transparency and identifying and preventing outcome switching and selective outcome reporting bias. Published IPV studies often differ from their records in trial registries. Researchers should pay close attention to the accuracy of trial registry records.

Uptake of a Dashboard Designed to Give Realtime Feedback to a Sentinel Network About Key Data Required for Influenza Vaccine Effectiveness Studies.

PubMed

Pathirannehelage, Sameera; Kumarapeli, Pushpa; Byford, Rachel; Yonova, Ivelina; Ferreira, Filipa; de Lusignan, Simon

2018-01-01

Dashboards are technologies that bringing together a range of data sources for observational or analytical purposes. We have created a customised dashboard that includes all the key data elements required for monitoring flu vaccine effectiveness (FVE). This delivers a unique dashboard for each primary care provider (general practice) providing data to the Royal College of General Practitioners (RCGP) Research and Surveillance Centre (RSC), one of the oldest European surveillance systems. These FVE studies use a test negative case control (TNCC) design. TNCC requires knowledge of practice denominator; vaccine exposure, and results of influenza virology swabs carried out to identify in an influenza-like-illness (ILI), a clinical diagnosis, really is influenza. The dashboard displays the denominator uploaded each week into the surveillance system, compared with the nationally known practice size (providing face-validity for the denominator); it identifies those exposed to the vaccine (by age group and risk category) and virology specimens taken and missed opportunities for surveillance (again by category). All sentinel practices can access in near real time (4 working days in areas) their rates of vaccine exposure and swabs conducted. Initial feedback is positive; 80% (32/40) practices responded positively.

Ocean bottom seismometer: design and test of a measurement system for marine seismology.

PubMed

Mànuel, Antoni; Roset, Xavier; Del Rio, Joaquin; Toma, Daniel Mihai; Carreras, Normandino; Panahi, Shahram Shariat; Garcia-Benadí, A; Owen, Tim; Cadena, Javier

2012-01-01

The Ocean Bottom Seismometer (OBS) is a key instrument for the geophysical study of sea sub-bottom layers. At present, more reliable autonomous instruments capable of recording underwater for long periods of time and therefore handling large data storage are needed. This paper presents a new Ocean Bottom Seismometer designed to be used in long duration seismic surveys. Power consumption and noise level of the acquisition system are the key points to optimize the autonomy and the data quality. To achieve our goals, a new low power data logger with high resolution and Signal-to-Noise Ratio (SNR) based on Compact Flash memory card is designed to enable continuous data acquisition. The equipment represents the achievement of joint work from different scientific and technological disciplines as electronics, mechanics, acoustics, communications, information technology, marine geophysics, etc. This easy to handle and sophisticated equipment allows the recording of useful controlled source and passive seismic data, as well as other time varying data, with multiple applications in marine environment research. We have been working on a series of prototypes for ten years to improve many of the aspects that make the equipment easy to handle and useful to work in deep-water areas. Ocean Bottom Seismometers (OBS) have received growing attention from the geoscience community during the last forty years. OBS sensors recording motion of the ocean floor hold key information in order to study offshore seismicity and to explore the Earth's crust. In a seismic survey, a series of OBSs are placed on the seabed of the area under study, where they record either natural seismic activity or acoustic signals generated by compressed air-guns on the ocean surface. The resulting data sets are subsequently used to model both the earthquake locations and the crustal structure.

Ocean Bottom Seismometer: Design and Test of a Measurement System for Marine Seismology

PubMed Central

Mànuel, Antoni; Roset, Xavier; Del Rio, Joaquin; Toma, Daniel Mihai; Carreras, Normandino; Panahi, Shahram Shariat; Garcia-Benadí, A.; Owen, Tim; Cadena, Javier

2012-01-01

The Ocean Bottom Seismometer (OBS) is a key instrument for the geophysical study of sea sub-bottom layers. At present, more reliable autonomous instruments capable of recording underwater for long periods of time and therefore handling large data storage are needed. This paper presents a new Ocean Bottom Seismometer designed to be used in long duration seismic surveys. Power consumption and noise level of the acquisition system are the key points to optimize the autonomy and the data quality. To achieve our goals, a new low power data logger with high resolution and Signal–to-Noise Ratio (SNR) based on Compact Flash memory card is designed to enable continuous data acquisition. The equipment represents the achievement of joint work from different scientific and technological disciplines as electronics, mechanics, acoustics, communications, information technology, marine geophysics, etc. This easy to handle and sophisticated equipment allows the recording of useful controlled source and passive seismic data, as well as other time varying data, with multiple applications in marine environment research. We have been working on a series of prototypes for ten years to improve many of the aspects that make the equipment easy to handle and useful to work in deep-water areas. Ocean Bottom Seismometers (OBS) have received growing attention from the geoscience community during the last forty years. OBS sensors recording motion of the ocean floor hold key information in order to study offshore seismicity and to explore the Earth’s crust. In a seismic survey, a series of OBSs are placed on the seabed of the area under study, where they record either natural seismic activity or acoustic signals generated by compressed air-guns on the ocean surface. The resulting data sets are subsequently used to model both the earthquake locations and the crustal structure. PMID:22737032

Experimental quantum key distribution with source flaws

NASA Astrophysics Data System (ADS)

Xu, Feihu; Wei, Kejin; Sajeed, Shihan; Kaiser, Sarah; Sun, Shihai; Tang, Zhiyuan; Qian, Li; Makarov, Vadim; Lo, Hoi-Kwong

2015-09-01

Decoy-state quantum key distribution (QKD) is a standard technique in current quantum cryptographic implementations. Unfortunately, existing experiments have two important drawbacks: the state preparation is assumed to be perfect without errors and the employed security proofs do not fully consider the finite-key effects for general attacks. These two drawbacks mean that existing experiments are not guaranteed to be proven to be secure in practice. Here, we perform an experiment that shows secure QKD with imperfect state preparations over long distances and achieves rigorous finite-key security bounds for decoy-state QKD against coherent attacks in the universally composable framework. We quantify the source flaws experimentally and demonstrate a QKD implementation that is tolerant to channel loss despite the source flaws. Our implementation considers more real-world problems than most previous experiments, and our theory can be applied to general discrete-variable QKD systems. These features constitute a step towards secure QKD with imperfect devices.

Magnetic-Nozzle Studies for Fusion Propulsion Applications: Gigawatt Plasma Source Operation and Magnetic Nozzle Analysis

NASA Technical Reports Server (NTRS)

Gilland, James H.; Mikekkides, Ioannis; Mikellides, Pavlos; Gregorek, Gerald; Marriott, Darin

2004-01-01

This project has been a multiyear effort to assess the feasibility of a key process inherent to virtually all fusion propulsion concepts: the expansion of a fusion-grade plasma through a diverging magnetic field. Current fusion energy research touches on this process only indirectly through studies of plasma divertors designed to remove the fusion products from a reactor. This project was aimed at directly addressing propulsion system issues, without the expense of constructing a fusion reactor. Instead, the program designed, constructed, and operated a facility suitable for simulating fusion reactor grade edge plasmas, and to examine their expansion in an expanding magnetic nozzle. The approach was to create and accelerate a dense (up to l0(exp 20)/m) plasma, stagnate it in a converging magnetic field to convert kinetic energy to thermal energy, and examine the subsequent expansion of the hot (100's eV) plasma in a subsequent magnetic nozzle. Throughout the project, there has been a parallel effort between theoretical and numerical design and modelling of the experiment and the experiment itself. In particular, the MACH2 code was used to design and predict the performance of the magnetoplasmadynamic (MPD) plasma accelerator, and to design and predict the design and expected behavior for the magnetic field coils that could be added later. Progress to date includes the theoretical accelerator design and construction, development of the power and vacuum systems to accommodate the powers and mass flow rates of interest to out research, operation of the accelerator and comparison to theoretical predictions, and computational analysis of future magnetic field coils and the expected performance of an integrated source-nozzle experiment.

The Cosmic Evolution Through UV Spectroscopy (CETUS) Probe Mission Concept

NASA Astrophysics Data System (ADS)

Danchi, William; Heap, Sara; Woodruff, Robert; Hull, Anthony; Kendrick, Stephen E.; Purves, Lloyd; McCandliss, Stephan; Kelly Dodson, Greg Mehle, James Burge, Martin Valente, Michael Rhee, Walter Smith, Michael Choi, Eric Stoneking

2018-01-01

CETUS is a mission concept for an all-UV telescope with 3 scientific instruments: a wide-field camera, a wide-field multi-object spectrograph, and a point-source high-resolution and medium resolution spectrograph. It is primarily intended to work with other survey telescopes in the 2020’s (e.g. E-ROSITA (X-ray), LSST, Subaru, WFIRST (optical-near-IR), SKA (radio) to solve major, outstanding problems in astrophysics. In this poster presentation, we give an overview of CETUS key science goals and a progress report on the CETUS mission and instrument design.

PULSION® HP: Tunable, High Productivity Plasma Doping

NASA Astrophysics Data System (ADS)

Felch, S. B.; Torregrosa, F.; Etienne, H.; Spiegel, Y.; Roux, L.; Turnbaugh, D.

2011-01-01

Plasma doping has been explored for many implant applications for over two decades and is now being used in semiconductor manufacturing for two applications: DRAM polysilicon counter-doping and contact doping. The PULSION HP is a new plasma doping tool developed by Ion Beam Services for high-volume production that enables customer control of the dominant mechanism—deposition, implant, or etch. The key features of this tool are a proprietary, remote RF plasma source that enables a high density plasma with low chamber pressure, resulting in a wide process space, and special chamber and wafer electrode designs that optimize doping uniformity.

Microbes to Biomes at Berkeley Lab

ScienceCinema

None

2018-06-21

Microbes are the Earth's most abundant and diverse form of life. Berkeley Lab's Microbes to Biomes initiative -- which will take advantage of research expertise at the Joint Genome Institute, Advanced Light Source, Molecular Foundry, and the new computational science facility -- is designed to explore and reveal the interactions of microbes with one another and with their environment. Microbes power our planet’s biogeochemical cycles, provide nutrients to our plants, purify our water and are integral components in keeping the human body free of disease and may hold the key to the Earth’s future.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ashenfelter, J.; Jaffe, D.; Diwan, M. V.

A meter-long, 23-liter EJ-309 liquid scintillator detector has been constructed to study the light collection and pulse-shape discrimination performance of elongated scintillator cells for the PROSPECT reactor antineutrino experiment. The magnitude and uniformity of light collection and neutron-gamma discrimination power in the energy range of antineutrino inverse beta decay products have been studied using gamma and spontaneous fission calibration sources deployed along the cell axis. We also study neutron-gamma discrimination and light collection abilities for differing PMT and reflector configurations. As a result, key design features for optimizing MeV-scale response and background rejection capabilities are identified.

Laboratory verification respiratory measurements. IMBLMS phase B.4, appendix C, section 13

NASA Technical Reports Server (NTRS)

1970-01-01

The B-4 IMBLMS preliminary design of the respiratory measurement element includes certain techniques and apparatus which are quite different from those included in the B-3 version previously delivered to NASA-MSC. A working model was constructed in the laboratory to prove the feasibility of certain key features. The most critical of these is the capability of switching sample gases into the mass spectrometer from two different sources during a single breath cycle. Results proved the feasibility of all of the concepts which were tested, and certain refinements and improvements were included, as well.

Methods of increasing net work output of organic Rankine cycles for low-grade waste heat recovery with a detailed analysis using a zeotropic working fluid mixture and scroll expander

NASA Astrophysics Data System (ADS)

Woodland, Brandon Jay

An organic Rankine cycle (ORC) is a thermodynamic cycle that is well-suited for waste heat recovery. It is generally employed for waste heat with temperatures in the range of 80 °C -- 300 °C. When the application is strictly to convert waste heat into work, thermal efficiency is not recommended as a key performance metric. In such an application, maximization of the net power output should be the objective rather than maximization of the thermal efficiency. Two alternative cycle configurations that can increase the net power produced from a heat source with a given temperature and flow rate are proposed and analyzed. These cycle configurations are 1) an ORC with two-phase flash expansion and 2) an ORC with a zeotropic working fluid mixture (ZRC). A design-stage ORC model is presented for consistent comparison of multiple ORC configurations. The finite capacity of the heat source and heat sink fluids is a key consideration in this model. Of all working fluids studied for the baseline ORC, R134a and R245fa yield the highest net power output from a given heat source. Results of the design-stage model indicate that the ORC with two-phase flash expansion offers the most improvement over the baseline ORC. However, the level of improvement that could be achieved in practice is highly uncertain due to the requirement of highly efficient two-phase expansion. The ZRC shows improvement over the baseline as long as the condenser fan power requirement is not negligible. At the highest estimated condenser fan power, the ZRC shows the most improvement, while the ORC with flash expansion is no longer beneficial. The ZRC was selected for detailed study because it does not require two-phase expansion. An experimental test rig was used to evaluate baseline ORC performance with R134a and with R245fa. The ZRC was tested on the same rig with a mixture of 62.5% R134a and 37.5% R245fa. The tested expander is a minimally-modified, of-the-shelf automotive scroll compressor. The high performance to cost ratio of this machine lends significant credence to the economic viability of small-scale, low-temperature ORCs. The experimental campaign covered two heat source temperatures, the full range of pump and expander speeds, a full range of heat source and heat sink fluid flow rates, and various charge levels for the three working fluids. This resulted in 366 steady-state measurements. The steady state measurements are used to develop a detailed ORC model. The model is based on multi-fluid performance maps for the pump and expander and a robust moving-boundary heat exchanger model. It is validated against the measured data and predicts the net power output of the tested ORC with a mean absolute percent error of 7.16%. Comparisons made with the detailed model confirm the predictions of the design-stage model. Using a conservative estimate of the condenser fan power, 19.1% improvement of the ZRC over the baseline ORC is indicated for a source temperature of 80 °C. For a 100 °C source temperature, 13.8% improvement is indicated. A key feature of the detailed ORC model is that it calculates the charge inventory of the working fluid in each heat exchanger and line set. Total system charge can also be specified as a model input. The model can represent the total charge well for R134a at low measured charge levels. As the measured charge level increases, the model becomes less accurate. Reasons for the deviation of the model at higher charge are investigated. It is expected that a charge tuning scheme could be employed to improve the accuracy of model-predicted charge.

Using turbidity for designing water networks.

PubMed

Castaño, J A; Higuita, J C

2016-05-01

Some methods to design water networks with minimum fresh water consumption are based on the selection of a key contaminant. In most of these "single contaminant methods", a maximum allowable concentration of contaminants must be established in water demands and water sources. Turbidity is not a contaminant concentration but is a property that represents the "sum" of other contaminants, with the advantage that it can be cheaper and easily measured than biological oxygen demand, chemical oxygen demand, suspended solids, dissolved solids, among others. The objective of this paper is to demonstrate that turbidity can be used directly in the design of water networks just like any other contaminant concentration. A mathematical demonstration is presented and in order to validate the mathematical results, the design of a water network for a guava fudge production process is performed. The material recovery pinch diagram and nearest neighbors algorithm were used for the design of the water network. Nevertheless, this water network could be designed using other single contaminant methodologies. The maximum error between the expected and the real turbidity values in the water network was 3.3%. These results corroborate the usefulness of turbidity in the design of water networks. Copyright © 2016 Elsevier Ltd. All rights reserved.

AMTEC radioisotope power system design and analysis for Pluto Express Fly-By

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hendricks, T.J.; Huang, C.; Sievers, R.K.

1997-12-31

The Pluto Express Fly-By program requires a Radioisotope Power System (RPS) to supply spacecraft power for various internal functions and mission instruments and experiments. AMTEC (Alkali-Metal Thermal-Electric Conversion) power conversion is the DOE-selected technology for an advanced, high-efficiency RPS to power the Pluto Express Fly-By spacecraft. An AMTEC-based RPS using the General Purpose Heat Source (GPHS) has been conceptually designed to satisfy the Pluto Express power requirements. Integrated AMTEC cell and system thermal/electrical design analyses, structural design analyses, and mass analyses were performed to define an optimum system design. Using fresh radioisotope fuel at beginning of mission, the RPS producesmore » 102 watts of power, has a mass of 8.35 kg (specific power density = 12.2 watts/kg), with a system conversion efficiency of 20.3%. Mass/power scale-up estimates have also been generated, indicating that a 150-watt version of this RPS would weigh approximately 11.3 kg. This paper presents and discusses the key features of this RPS design, the design and analysis methodology, and the numerous system and AMTEC cell tradeoff studies establishing the optimum AMTEC-based RPS.« less

Cryogenic ultra-high power infrared diode laser bars

NASA Astrophysics Data System (ADS)

Crump, Paul; Frevert, C.; Hösler, H.; Bugge, F.; Knigge, S.; Pittroff, W.; Erbert, G.; Tränkle, G.

2014-02-01

GaAs-based high power diode lasers are the most efficient source of optical energy, and are in wide use in industrial applications, either directly or as pump sources for other laser media. Increased output power per laser is required to enable new applications (increased optical power density) and to reduce cost (more output per component leads to lower cost in $/W). For example, laser bars in the 9xx nm wavelength range with the very highest power and efficiency are needed as pump sources for many high-energy-class solid-state laser systems. We here present latest performance progress using a novel design approach that leverages operation at temperatures below 0°C for increases in bar power and efficiency. We show experimentally that operation at -55°C increases conversion efficiency and suppresses thermal rollover, enabling peak quasi-continuous wave bar powers of Pout > 1.6 kW to be achieved (1.2 ms, 10 Hz), limited by the available current. The conversion efficiency at 1.6 kW is 53%. Following on from this demonstration work, the key open challenge is to develop designs that deliver higher efficiencies, targeting > 80% at 1.6 kW. We present an analysis of the limiting factors and show that low electrical resistance is crucial, meaning that long resonators and high fill factor are needed. We review also progress in epitaxial design developments that leverage low temperatures to enable both low resistance and high optical performance. Latest results will be presented, summarizing the impact on bar performance and options for further improvements to efficiency will also be reviewed.

Global Inter-Laboratory Fecal Source Identification Methods Comparison Study

EPA Science Inventory

Source tracking is key to identifying sources of fecal contamination for remediation as well as risk assessment. Previous intra- and inter-lab studies have investigated the performance of human and cow-associated source tracking markers, as well as library-dependent fecal source ...

Attacks exploiting deviation of mean photon number in quantum key distribution and coin tossing

NASA Astrophysics Data System (ADS)

Sajeed, Shihan; Radchenko, Igor; Kaiser, Sarah; Bourgoin, Jean-Philippe; Pappa, Anna; Monat, Laurent; Legré, Matthieu; Makarov, Vadim

2015-03-01

The security of quantum communication using a weak coherent source requires an accurate knowledge of the source's mean photon number. Finite calibration precision or an active manipulation by an attacker may cause the actual emitted photon number to deviate from the known value. We model effects of this deviation on the security of three quantum communication protocols: the Bennett-Brassard 1984 (BB84) quantum key distribution (QKD) protocol without decoy states, Scarani-Acín-Ribordy-Gisin 2004 (SARG04) QKD protocol, and a coin-tossing protocol. For QKD we model both a strong attack using technology possible in principle and a realistic attack bounded by today's technology. To maintain the mean photon number in two-way systems, such as plug-and-play and relativistic quantum cryptography schemes, bright pulse energy incoming from the communication channel must be monitored. Implementation of a monitoring detector has largely been ignored so far, except for ID Quantique's commercial QKD system Clavis2. We scrutinize this implementation for security problems and show that designing a hack-proof pulse-energy-measuring detector is far from trivial. Indeed, the first implementation has three serious flaws confirmed experimentally, each of which may be exploited in a cleverly constructed Trojan-horse attack. We discuss requirements for a loophole-free implementation of the monitoring detector.

Alternative IT Sourcing Strategies: From the Campus to the Cloud. ECAR Key Findings

ERIC Educational Resources Information Center

Goldstein, Philip J.

2009-01-01

This document presents the key findings from the 2009 ECAR (EDUCAUSE Center for Applied Research) study, "Alternative IT Sourcing Strategies: From the Campus to the Cloud," by Philip J. Goldstein. The study explores a multitude of strategies used by colleges and university information technology organizations to deliver the breadth of technologies…

Technology support to a telehealth in the home service: Qualitative observations.

PubMed

Taylor, Alan; Wade, Victoria; Morris, Greg; Pech, Joanne; Rechter, Stuart; Kidd, Michael; Carati, Colin

2016-07-01

The Flinders University Telehealth in the Home (FTH) trial was an action research initiative that introduced and evaluated the impact of telehealth services on palliative care patients living in the community, home-based rehabilitation services for the elderly, and services to the elderly in residential aged care. The aim of this study was to understand the issues encountered during the provision of technology services that supported this trial. A mixed methods approach was undertaken to analyse the roles of information and communication technology (ICT) and clinical staff in design, technology management and training. The data sources were staff observations and documents including job logs, meetings, emails and technology descriptions. Use of consumer technology for telehealth required customisation of applications and services. Clinicians played a key role in definition of applications and the embedding of workflow into applications. Usability of applications was key to their subsequent use. Management of design creep and technology services, coupled with support and training for clinicians were important to maintenance of a telehealth service. In the setting described, an iterative approach to the development of telehealth services to the home using consumer technologies was needed. The efficient management of consumer devices in multiple settings will become critical as telehealth services grow in scale. Effective collaboration between clinical and technical stakeholders and further workforce education in telehealth can be key enablers for the transition of face-to-face care to a telehealth mode of delivery. © The Author(s) 2015.

mdFoam+: Advanced molecular dynamics in OpenFOAM

NASA Astrophysics Data System (ADS)

Longshaw, S. M.; Borg, M. K.; Ramisetti, S. B.; Zhang, J.; Lockerby, D. A.; Emerson, D. R.; Reese, J. M.

2018-03-01

This paper introduces mdFoam+, which is an MPI parallelised molecular dynamics (MD) solver implemented entirely within the OpenFOAM software framework. It is open-source and released under the same GNU General Public License (GPL) as OpenFOAM. The source code is released as a publicly open software repository that includes detailed documentation and tutorial cases. Since mdFoam+ is designed entirely within the OpenFOAM C++ object-oriented framework, it inherits a number of key features. The code is designed for extensibility and flexibility, so it is aimed first and foremost as an MD research tool, in which new models and test cases can be developed and tested rapidly. Implementing mdFoam+ in OpenFOAM also enables easier development of hybrid methods that couple MD with continuum-based solvers. Setting up MD cases follows the standard OpenFOAM format, as mdFoam+ also relies upon the OpenFOAM dictionary-based directory structure. This ensures that useful pre- and post-processing capabilities provided by OpenFOAM remain available even though the fully Lagrangian nature of an MD simulation is not typical of most OpenFOAM applications. Results show that mdFoam+ compares well to another well-known MD code (e.g. LAMMPS) in terms of benchmark problems, although it also has additional functionality that does not exist in other open-source MD codes.

Microbially mediated carbon mineralization: Geoengineering a carbon-neutral mine

NASA Astrophysics Data System (ADS)

Power, I. M.; McCutcheon, J.; Harrison, A. L.; Wilson, S. A.; Dipple, G. M.; Southam, G.

2013-12-01

Ultramafic and mafic mine tailings are a potentially valuable feedstock for carbon mineralization, affording the mining industry an opportunity to completely offset their carbon emissions. Passive carbon mineralization has previously been documented at the abandoned Clinton Creek asbestos mine, and the active Diavik diamond mine and Mount Keith nickel mine, yet the majority of tailings remain unreacted. Examples of microbe-carbonate interactions at each mine suggest that biological pathways could be harnessed to promote carbon mineralization. In suitable environmental conditions, microbes can mediate geochemical processes to accelerate mineral dissolution, increase the supply of carbon dioxide (CO2), and induce carbonate precipitation, all of which may accelerate carbon mineralization. Tailings mineralogy and the availability of a CO2 point source are key considerations in designing tailings storage facilities (TSF) for optimizing carbon mineralization. We evaluate the efficacy of acceleration strategies including bioleaching, biologically induced carbonate precipitation, and heterotrophic oxidation of waste organics, as well as abiotic strategies including enhancing passive carbonation through modifying tailings management practices and use of CO2 point sources (Fig. 1). With the aim of developing carbon-neutral mines, implementation of carbon mineralization strategies into TSF design will be driven by economic incentives and public pressure for environmental sustainability in the mining industry. Figure 1. Schematic illustrating geoengineered scenarios for carbon mineralization of ultramafic mine tailings. Scenarios A and B are based on non-point and point sources of CO2, respectively.

Mercury target R&D for the Oak Ridge spallation neutron source

DOE Office of Scientific and Technical Information (OSTI.GOV)

Haines, J.R.; DiStefano, J.; Farrell, K.

1996-06-01

The conceptual design for the Oak Ridge Spallation Neutron Source (ORSNS) incorporates liquid mercury as its reference target material. A flowing liquid target was selected mainly because of the increased power handling capability possible with the convective transport process. The major reasons for choosing mercury as the liquid target material are because it: (1) is a liquid at room temperature, (2) has good heat transport properties, and (3) has a high atomic number and mass density resulting in high neutron yield and source brightness. Since liquid targets are not widely utilized in presently operating accelerator targets and because of themore » challenges posed by the intense, pulsed thermal energy deposition ({approximately}20-100 kJ deposited during each 1-10 {mu}s pulse), considerable R&D is planned for the mercury target concept. The key feasibility issue that will be addressed in early R&D efforts are the effects of the thermal shock environment, which will include development and testing of approaches to mitigate these effects. Materials compatiblity and ES&H issues associated with the use of liquid mercury are also of major importance in early R&D efforts. A brief description of the mercury target design concept, results of initial evaluations of its performance characteristics, identification of its critical issues, and an outline of the R&D program aimed at addressing these issues will be presented.« less

How to implement decoy-state quantum key distribution for a satellite uplink with 50-dB channel loss

NASA Astrophysics Data System (ADS)

Meyer-Scott, Evan; Yan, Zhizhong; MacDonald, Allison; Bourgoin, Jean-Philippe; Hübel, Hannes; Jennewein, Thomas

2011-12-01

Quantum key distribution (QKD) takes advantage of fundamental properties of quantum physics to allow two distant parties to share a secret key; however, QKD is hampered by a distance limitation of a few hundred kilometers on Earth. The most immediate solution for global coverage is to use a satellite, which can receive separate QKD transmissions from two or more ground stations and act as a trusted node to link these ground stations. In this article we report on a system capable of performing QKD in the high loss regime expected in an uplink to a satellite using weak coherent pulses and decoy states. Such a scenario profits from the simplicity of its receiver payload, but has so far been considered to be infeasible due to very high transmission losses (40-50 dB). The high loss is overcome by implementing an innovative photon source and advanced timing analysis. Our system handles up to 57 dB photon loss in the infinite key limit, confirming the viability of the satellite uplink scenario. We emphasize that while this system was designed with a satellite uplink in mind, it could just as easily overcome high losses on any free space QKD link.

Quantum key distribution with entangled photon sources

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ma Xiongfeng; Fung, Chi-Hang Fred; Lo, H.-K.

2007-07-15

A parametric down-conversion (PDC) source can be used as either a triggered single-photon source or an entangled-photon source in quantum key distribution (QKD). The triggering PDC QKD has already been studied in the literature. On the other hand, a model and a post-processing protocol for the entanglement PDC QKD are still missing. We fill in this important gap by proposing such a model and a post-processing protocol for the entanglement PDC QKD. Although the PDC model is proposed to study the entanglement-based QKD, we emphasize that our generic model may also be useful for other non-QKD experiments involving a PDCmore » source. Since an entangled PDC source is a basis-independent source, we apply Koashi and Preskill's security analysis to the entanglement PDC QKD. We also investigate the entanglement PDC QKD with two-way classical communications. We find that the recurrence scheme increases the key rate and the Gottesman-Lo protocol helps tolerate higher channel losses. By simulating a recent 144-km open-air PDC experiment, we compare three implementations: entanglement PDC QKD, triggering PDC QKD, and coherent-state QKD. The simulation result suggests that the entanglement PDC QKD can tolerate higher channel losses than the coherent-state QKD. The coherent-state QKD with decoy states is able to achieve highest key rate in the low- and medium-loss regions. By applying the Gottesman-Lo two-way post-processing protocol, the entanglement PDC QKD can tolerate up to 70 dB combined channel losses (35 dB for each channel) provided that the PDC source is placed in between Alice and Bob. After considering statistical fluctuations, the PDC setup can tolerate up to 53 dB channel losses.« less

Key Source Habitats and Potential Dispersal of Triatoma infestans Populations in Northwestern Argentina: Implications for Vector Control

PubMed Central

Gürtler, Ricardo E.; Cecere, María C.; Fernández, María del Pilar; Vazquez-Prokopec, Gonzalo M.; Ceballos, Leonardo A.; Gurevitz, Juan M.; Kitron, Uriel; Cohen, Joel E.

2014-01-01

Background Triatoma infestans —the principal vector of the infection that causes Chagas disease— defies elimination efforts in the Gran Chaco region. This study identifies the types of human-made or -used structures that are key sources of these bugs in the initial stages of house reinfestation after an insecticide spraying campaign. Methodology and Principal Findings We measured demographic and blood-feeding parameters at two geographic scales in 11 rural communities in Figueroa, northwest Argentina. Of 1,297 sites searched in spring, 279 (21.5%) were infested. Bug abundance per site and female fecundity differed significantly among habitat types (ecotopes) and were highly aggregated. Domiciles (human sleeping quarters) had maximum infestation prevalence (38.7%), human-feeding bugs and total egg production, with submaximal values for other demographic and blood-feeding attributes. Taken collectively peridomestic sites were three times more often infested than domiciles. Chicken coops had greater bug abundance, blood-feeding rates, engorgement status, and female fecundity than pig and goat corrals. The host-feeding patterns were spatially structured yet there was strong evidence of active dispersal of late-stage bugs between ecotopes. Two flight indices predicted that female fliers were more likely to originate from kitchens and domiciles, rejecting our initial hypothesis that goat and pig corrals would dominate. Conclusions and Significance Chicken coops and domiciles were key source habitats fueling rapid house reinfestation. Focusing control efforts on ecotopes with human-fed bugs (domiciles, storerooms, goat corrals) would neither eliminate the substantial contributions to bug population growth from kitchens, chicken coops, and pig corrals nor stop dispersal of adult female bugs from kitchens. Rather, comprehensive control of the linked network of ecotopes is required to prevent feeding on humans, bug population growth, and bug dispersal simultaneously. Our study illustrates a demographic approach that may be applied to other regions and triatomine species for the design of innovative, improved vector control strategies. PMID:25299653

Success Factors of European Syndromic Surveillance Systems: A Worked Example of Applying Qualitative Comparative Analysis

PubMed Central

Ziemann, Alexandra; Fouillet, Anne; Brand, Helmut; Krafft, Thomas

2016-01-01

Introduction Syndromic surveillance aims at augmenting traditional public health surveillance with timely information. To gain a head start, it mainly analyses existing data such as from web searches or patient records. Despite the setup of many syndromic surveillance systems, there is still much doubt about the benefit of the approach. There are diverse interactions between performance indicators such as timeliness and various system characteristics. This makes the performance assessment of syndromic surveillance systems a complex endeavour. We assessed if the comparison of several syndromic surveillance systems through Qualitative Comparative Analysis helps to evaluate performance and identify key success factors. Materials and Methods We compiled case-based, mixed data on performance and characteristics of 19 syndromic surveillance systems in Europe from scientific and grey literature and from site visits. We identified success factors by applying crisp-set Qualitative Comparative Analysis. We focused on two main areas of syndromic surveillance application: seasonal influenza surveillance and situational awareness during different types of potentially health threatening events. Results We found that syndromic surveillance systems might detect the onset or peak of seasonal influenza earlier if they analyse non-clinical data sources. Timely situational awareness during different types of events is supported by an automated syndromic surveillance system capable of analysing multiple syndromes. To our surprise, the analysis of multiple data sources was no key success factor for situational awareness. Conclusions We suggest to consider these key success factors when designing or further developing syndromic surveillance systems. Qualitative Comparative Analysis helped interpreting complex, mixed data on small-N cases and resulted in concrete and practically relevant findings. PMID:27182731

Substance Use Stigma: Reliability and validity of a theory-based scale for substance-using populations*

PubMed Central

Smith, Laramie R.; Earnshaw, Valerie A.; Copenhaver, Michael M.; Cunningham, Chinazo O.

2016-01-01

Background Substance use disorders consistently rank among the most stigmatized conditions worldwide. Thus, substance use stigma fosters health inequities among persons with substance use disorders and remains a key barrier to successful screening and treatment efforts. Current efforts to measure substance use stigma are limited. This study aims to advance measurement efforts by drawing on stigma theory to develop and evaluate the Substance Use Stigma Mechanisms Scale (SU-SMS). The SU-SMS was designed to capture enacted, anticipated, and internalized substance use stigma mechanisms among persons with current and past substance use disorders, and distinguish between key stigma sources most likely to impact this target population. Methods This study was a cross-sectional evaluation of the validity, reliability, and generalizability of the SU-SMS across two independent samples with diverse substance use and treatment histories. Results Findings support the structural and construct validity of the SU-SMS, suggesting the scale was able to capture enacted, anticipated, and internalized stigma as distinct stigma experiences. It also further differentiated between two distinct stigma sources (family and healthcare providers). Analysis of these mechanisms and psychosocial metrics suggests that the scale is also associated with other health-related outcomes. Furthermore, the SU-SMS demonstrated high levels of internal reliability and generalizability across two independent samples of persons with diverse substance use disorders and treatment histories. Conclusion The SU-SMS may serve as a valuable tool for better understanding the processes through which substance use stigma serves to undermine key health behaviors and outcomes among persons with substance use disorders. PMID:26972790

Success Factors of European Syndromic Surveillance Systems: A Worked Example of Applying Qualitative Comparative Analysis.

PubMed

Ziemann, Alexandra; Fouillet, Anne; Brand, Helmut; Krafft, Thomas

2016-01-01

Syndromic surveillance aims at augmenting traditional public health surveillance with timely information. To gain a head start, it mainly analyses existing data such as from web searches or patient records. Despite the setup of many syndromic surveillance systems, there is still much doubt about the benefit of the approach. There are diverse interactions between performance indicators such as timeliness and various system characteristics. This makes the performance assessment of syndromic surveillance systems a complex endeavour. We assessed if the comparison of several syndromic surveillance systems through Qualitative Comparative Analysis helps to evaluate performance and identify key success factors. We compiled case-based, mixed data on performance and characteristics of 19 syndromic surveillance systems in Europe from scientific and grey literature and from site visits. We identified success factors by applying crisp-set Qualitative Comparative Analysis. We focused on two main areas of syndromic surveillance application: seasonal influenza surveillance and situational awareness during different types of potentially health threatening events. We found that syndromic surveillance systems might detect the onset or peak of seasonal influenza earlier if they analyse non-clinical data sources. Timely situational awareness during different types of events is supported by an automated syndromic surveillance system capable of analysing multiple syndromes. To our surprise, the analysis of multiple data sources was no key success factor for situational awareness. We suggest to consider these key success factors when designing or further developing syndromic surveillance systems. Qualitative Comparative Analysis helped interpreting complex, mixed data on small-N cases and resulted in concrete and practically relevant findings.

IsoDesign: a software for optimizing the design of 13C-metabolic flux analysis experiments.

PubMed

Millard, Pierre; Sokol, Serguei; Letisse, Fabien; Portais, Jean-Charles

2014-01-01

The growing demand for (13) C-metabolic flux analysis ((13) C-MFA) in the field of metabolic engineering and systems biology is driving the need to rationalize expensive and time-consuming (13) C-labeling experiments. Experimental design is a key step in improving both the number of fluxes that can be calculated from a set of isotopic data and the precision of flux values. We present IsoDesign, a software that enables these parameters to be maximized by optimizing the isotopic composition of the label input. It can be applied to (13) C-MFA investigations using a broad panel of analytical tools (MS, MS/MS, (1) H NMR, (13) C NMR, etc.) individually or in combination. It includes a visualization module to intuitively select the optimal label input depending on the biological question to be addressed. Applications of IsoDesign are described, with an example of the entire (13) C-MFA workflow from the experimental design to the flux map including important practical considerations. IsoDesign makes the experimental design of (13) C-MFA experiments more accessible to a wider biological community. IsoDesign is distributed under an open source license at http://metasys.insa-toulouse.fr/software/isodes/ © 2013 Wiley Periodicals, Inc.

Acoustic Source Localization via Time Difference of Arrival Estimation for Distributed Sensor Networks Using Tera-Scale Optical Core Devices

DOE PAGES

Imam, Neena; Barhen, Jacob

2009-01-01

For real-time acoustic source localization applications, one of the primary challenges is the considerable growth in computational complexity associated with the emergence of ever larger, active or passive, distributed sensor networks. These sensors rely heavily on battery-operated system components to achieve highly functional automation in signal and information processing. In order to keep communication requirements minimal, it is desirable to perform as much processing on the receiver platforms as possible. However, the complexity of the calculations needed to achieve accurate source localization increases dramatically with the size of sensor arrays, resulting in substantial growth of computational requirements that cannot bemore » readily met with standard hardware. One option to meet this challenge builds upon the emergence of digital optical-core devices. The objective of this work was to explore the implementation of key building block algorithms used in underwater source localization on the optical-core digital processing platform recently introduced by Lenslet Inc. This demonstration of considerably faster signal processing capability should be of substantial significance to the design and innovation of future generations of distributed sensor networks.« less

Viking-Age Sails: Form and Proportion

NASA Astrophysics Data System (ADS)

Bischoff, Vibeke

2017-04-01

Archaeological ship-finds have shed much light on the design and construction of vessels from the Viking Age. However, the exact proportions of their sails remain unknown due to the lack of fully preserved sails, or other definite indicators of their proportions. Key Viking-Age ship-finds from Scandinavia—the Oseberg Ship, the Gokstad Ship and Skuldelev 3—have all revealed traces of rigging. In all three finds, the keelson—with the mast position—is preserved, together with fastenings for the sheets and the tack, indicating the breadth of the sail. The sail area can then be estimated based on practical experience of how large a sail the specific ship can carry, in conjunction with hull form and displacement. This article presents reconstructions of the form and dimensions of rigging and sail based on the archaeological finds, evidence from iconographic and written sources, and ethnographic parallels with traditional Nordic boats. When these sources are analysed, not only do the similarities become apparent, but so too does the relative disparity between the archaeological record and the other sources. Preferential selection in terms of which source is given the greatest merit is therefore required, as it is not possible to afford them all equal value.

Arbitrarily shaped high-coherence electron bunches from cold atoms

NASA Astrophysics Data System (ADS)

McCulloch, A. J.; Sheludko, D. V.; Saliba, S. D.; Bell, S. C.; Junker, M.; Nugent, K. A.; Scholten, R. E.

2011-10-01

Ultrafast electron diffractive imaging of nanoscale objects such as biological molecules and defects in solid-state devices provides crucial information on structure and dynamic processes: for example, determination of the form and function of membrane proteins, vital for many key goals in modern biological science, including rational drug design. High brightness and high coherence are required to achieve the necessary spatial and temporal resolution, but have been limited by the thermal nature of conventional electron sources and by divergence due to repulsive interactions between the electrons, known as the Coulomb explosion. It has been shown that, if the electrons are shaped into ellipsoidal bunches with uniform density, the Coulomb explosion can be reversed using conventional optics, to deliver the maximum possible brightness at the target. Here we demonstrate arbitrary and real-time control of the shape of cold electron bunches extracted from laser-cooled atoms. The ability to dynamically shape the electron source itself and to observe this shape in the propagated electron bunch provides a remarkable experimental demonstration of the intrinsically high spatial coherence of a cold-atom electron source, and the potential for alleviation of electron-source brightness limitations due to Coulomb explosion.

Absorption cooling sources atmospheric emissions decrease by implementation of simple algorithm for limiting temperature of cooling water

NASA Astrophysics Data System (ADS)

Wojdyga, Krzysztof; Malicki, Marcin

2017-11-01

Constant strive to improve the energy efficiency forces carrying out activities aimed at reduction of energy consumption hence decreasing amount of contamination emissions to atmosphere. Cooling demand, both for air-conditioning and process cooling, plays an increasingly important role in the balance of Polish electricity generation and distribution system in summer. During recent years' demand for electricity during summer months has been steadily and significantly increasing leading to deficits of energy availability during particularly hot periods. This causes growing importance and interest in trigeneration power generation sources and heat recovery systems producing chilled water. Key component of such system is thermally driven chiller, mostly absorption, based on lithium-bromide and water mixture. Absorption cooling systems also exist in Poland as stand-alone systems, supplied with heating from various sources, generated solely for them or recovered as waste or useless energy. The publication presents a simple algorithm, designed to reduce the amount of heat for the supply of absorption chillers producing chilled water for the purposes of air conditioning by reducing the temperature of the cooling water, and its impact on decreasing emissions of harmful substances into the atmosphere. Scale of environmental advantages has been rated for specific sources what enabled evaluation and estimation of simple algorithm implementation to sources existing nationally.

Opportunities and Challenges in Supply-Side Simulation: Physician-Based Models

PubMed Central

Gresenz, Carole Roan; Auerbach, David I; Duarte, Fabian

2013-01-01

Objective To provide a conceptual framework and to assess the availability of empirical data for supply-side microsimulation modeling in the context of health care. Data Sources Multiple secondary data sources, including the American Community Survey, Health Tracking Physician Survey, and SK&A physician database. Study Design We apply our conceptual framework to one entity in the health care market—physicians—and identify, assess, and compare data available for physician-based simulation models. Principal Findings Our conceptual framework describes three broad types of data required for supply-side microsimulation modeling. Our assessment of available data for modeling physician behavior suggests broad comparability across various sources on several dimensions and highlights the need for significant integration of data across multiple sources to provide a platform adequate for modeling. A growing literature provides potential estimates for use as behavioral parameters that could serve as the models' engines. Sources of data for simulation modeling that account for the complex organizational and financial relationships among physicians and other supply-side entities are limited. Conclusions A key challenge for supply-side microsimulation modeling is optimally combining available data to harness their collective power. Several possibilities also exist for novel data collection. These have the potential to serve as catalysts for the next generation of supply-side-focused simulation models to inform health policy. PMID:23347041

Phase-encoded measurement device independent quantum key distribution without a shared reference frame

NASA Astrophysics Data System (ADS)

Zhuo-Dan, Zhu; Shang-Hong, Zhao; Chen, Dong; Ying, Sun

2018-07-01

In this paper, a phase-encoded measurement device independent quantum key distribution (MDI-QKD) protocol without a shared reference frame is presented, which can generate secure keys between two parties while the quantum channel or interferometer introduces an unknown and slowly time-varying phase. The corresponding secret key rate and single photons bit error rate is analysed, respectively, with single photons source (SPS) and weak coherent source (WCS), taking finite-key analysis into account. The numerical simulations show that the modified phase-encoded MDI-QKD protocol has apparent superiority both in maximal secure transmission distance and key generation rate while possessing the improved robustness and practical security in the high-speed case. Moreover, the rejection of the frame-calibrating part will intrinsically reduce the consumption of resources as well as the potential security flaws of practical MDI-QKD systems.

Key data elements for use in cost-utility modeling of biological treatments for rheumatoid arthritis.

PubMed

Ganz, Michael L; Hansen, Brian Bekker; Valencia, Xavier; Strandberg-Larsen, Martin

2015-05-01

Economic evaluation is becoming more common and important as new biologic therapies for rheumatoid arthritis (RA) are developed. While much has been published about how to design cost-utility models for RA to conduct these evaluations, less has been written about the sources of data populating those models. The goal is to review the literature and to provide recommendations for future data collection efforts. This study reviewed RA cost-utility models published between January 2006 and February 2014 focusing on five key sources of data (health-related quality-of-life and utility, clinical outcomes, disease progression, course of treatment, and healthcare resource use and costs). It provided recommendations for collecting the appropriate data during clinical and other studies to support modeling of biologic treatments for RA. Twenty-four publications met the selection criteria. Almost all used two steps to convert clinical outcomes data to utilities rather than more direct methods; most did not use clinical outcomes measures that captured absolute levels of disease activity and physical functioning; one-third of them, in contrast with clinical reality, assumed zero disease progression for biologic-treated patients; little more than half evaluated courses of treatment reflecting guideline-based or actual clinical care; and healthcare resource use and cost data were often incomplete. Based on these findings, it is recommended that future studies collect clinical outcomes and health-related quality-of-life data using appropriate instruments that can convert directly to utilities; collect data on actual disease progression; be designed to capture real-world courses of treatment; and collect detailed data on a wide range of healthcare resources and costs.

Use of an Innovative Personality-Mindset Profiling Tool to Guide Culture-Change Strategies among Different Healthcare Worker Groups.

PubMed

Grayson, M Lindsay; Macesic, Nenad; Huang, G Khai; Bond, Katherine; Fletcher, Jason; Gilbert, Gwendolyn L; Gordon, David L; Hellsten, Jane F; Iredell, Jonathan; Keighley, Caitlin; Stuart, Rhonda L; Xuereb, Charles S; Cruickshank, Marilyn

2015-01-01

Important culture-change initiatives (e.g. improving hand hygiene compliance) are frequently associated with variable uptake among different healthcare worker (HCW) categories. Inherent personality differences between these groups may explain change uptake and help improve future intervention design. We used an innovative personality-profiling tool (ColourGrid®) to assess personality differences among standard HCW categories at five large Australian hospitals using two data sources (HCW participant surveys [PS] and generic institution-wide human resource [HR] data) to: a) compare the relative accuracy of these two sources; b) identify differences between HCW groups and c) use the observed profiles to guide design strategies to improve uptake of three clinically-important initiatives (improved hand hygiene, antimicrobial stewardship and isolation procedure adherence). Results from 34,243 HCWs (HR data) and 1045 survey participants (PS data) suggest that HCWs were different from the general population, displaying more individualism, lower power distance, less uncertainty avoidance and greater cynicism about advertising messages. HR and PS data were highly concordant in identifying differences between the three key HCW categories (doctors, nursing/allied-health, support services) and predicting appropriate implementation strategies. Among doctors, the data suggest that key messaging should differ between full-time vs part-time (visiting) senior medical officers (SMO, VMO) and junior hospital medical officers (HMO), with SMO messaging focused on evidence-based compliance, VMO initiatives emphasising structured mandatory controls and prestige loss for non-adherence, and for HMOs focusing on leadership opportunity and future career risk for non-adherence. Compared to current standardised approaches, targeted interventions based on personality differences between HCW categories should result in improved infection control-related culture-change uptake. Personality profiling based on HR data may represent a useful means of developing a national culture-change "blueprint" for HCW education.

Challenges in conducting post-authorisation safety studies (PASS): A vaccine manufacturer's view.

PubMed

Cohet, Catherine; Rosillon, Dominique; Willame, Corinne; Haguinet, Francois; Marenne, Marie-Noëlle; Fontaine, Sandrine; Buyse, Hubert; Bauchau, Vincent; Baril, Laurence

2017-05-25

Post-authorisation safety studies (PASS) of vaccines assess or quantify the risk of adverse events following immunisation that were not identified or could not be estimated pre-licensure. The aim of this perspective paper is to describe the authors' experience in the design and conduct of twelve PASS that contributed to the evaluation of the benefit-risk of vaccines in real-world settings. We describe challenges and learnings from selected PASS of rotavirus, malaria, influenza, human papillomavirus and measles-mumps-rubella-varicella vaccines that assessed or identified potential or theoretical risks, which may lead to changes to risk management plans and/or to label updates. Study settings include the use of large healthcare databases and de novo data collection. PASS methodology is influenced by the background incidence of the outcome of interest, vaccine uptake, availability and quality of data sources, identification of the at-risk population and of suitable comparators, availability of validated case definitions, and the frequent need for case ascertainment in large databases. Challenges include the requirement for valid exposure and outcome data, identification of, and access to, adequate data sources, and mitigating limitations including bias and confounding. Assessing feasibility is becoming a key step to confirm that study objectives can be met in a timely manner. PASS provide critical information for regulators, public health agencies, vaccine manufacturers and ultimately, individuals. Collaborative approaches and synergistic efforts between vaccine manufacturers and key stakeholders, such as regulatory and public health agencies, are needed to facilitate access to data, and to drive optimal study design and implementation, with the aim of generating robust evidence. Copyright © 2017 GSK Biologicals SA. Published by Elsevier Ltd.. All rights reserved.

Breast cancer policy in Latin America: account of achievements and challenges in five countries.

PubMed

Nigenda, Gustavo; Gonzalez-Robledo, Maria Cecilia; Gonzalez-Robledo, Luz Maria; Bejarano-Arias, Rosa Maria

2016-07-12

The recent increase of breast cancer mortality has put on alert to most countries in the region. However it has taken some time before breast cancer could be considered as a relevant problem. Only in recent years breast cancer has been considered a priority in some Latin American countries and resources have been mobilized to confront the problem at the institutional level. The article analyzes the efforts made in five Latin American countries (Argentina, Brazil, Colombia, Mexico and Venezuela) in the last 15 years to design and implement policies to address the growing incidence of breast cancer. Data was collected between July and December 2010 from both primary and secondary sources. Semi-structured interviews were conducted with key informants from governmental and non-governmental organizations. Secondary data was obtained from publications in journals, government reports and official statistics in each country. Analysis combines information from both types of sources. Countries have followed different paths and are in different stages of policy implementation. In all cases early detection is a key strategy. Through the design of programs and guidelines, the allocation of financial resources to treat patients, as well as a formally structured information system, Brazil and Mexico have been able to set up comprehensive national policies. Argentina, Colombia and Venezuela have made important advancements but not yet capable of coordinating comprehensive national policies. Breast cancer is being considered a priority in all five countries but there are different stages in the rolling out of comprehensive national policies due to differences in their capacity to allocate resources, implement operational strategies and encourage the participation of relevant stakeholders.

The Use of Social Networking Sites (SNSs) in Health Communication Campaigns: Review and Recommendations.

PubMed

Shi, Jingyuan; Poorisat, Thanomwong; Salmon, Charles T

2018-01-01

The past decade has witnessed a rapid increase in the use of Social Networking Sites (SNSs) in health communication campaigns seeking to achieve an ambitious range of health-related impacts. This article provides a review of 40 studies and research protocols, with a focus on two key factors that differentiate SNSs from more traditional health communication approaches of the past. The first is the potential dualism between message sender and receiver, in which receivers become receiver-sources who forward and amplify the content and reach of health messages. The second is the potential dualism between message and message impact, in which the act of forwarding and modifying messages by receiver-sources itself becomes a measure of message impact. Each of these dualisms has implications for the design and evaluation of contemporary health communication campaigns. The review concludes with a series of observations and recommendations for future health communication research.

Simulations towards optimization of a neutron/anti-neutron oscillation experiment at the European Spallation Source

NASA Astrophysics Data System (ADS)

Frost, Matthew; Kamyshkov, Yuri; Castellanos, Luis; Klinkby, Esben; US NNbar Collaboration

2015-04-01

The observation of Neutron/Anti-neutron oscillation would prove the existence of Baryon Number Violation (BNV), and thus an explanation for the dominance of matter over anti-matter in the universe. The latest experiments have shown the oscillation time to be greater than 8.6 x 107 seconds, whereas current theoretical predictions suggest times on the order of 108 to 109 seconds. A neutron oscillation experiment proposed at the European Spallation Source (ESS) would provide sensitivity of more than 1000 times previous experiments performed, thus providing a result well-suited to confirm or deny current theory. A conceptual design of the proposed experiment will be presented, as well as the optimization of key experiment components using Monte-Carlo simulation methods, including the McStas neutron ray-trace simulation package. This work is supported by the Organized Research Units Program funded by The University of Tennessee, Knoxville Office of Research and Engagement.

Development of a 500-Watt portable generator

NASA Astrophysics Data System (ADS)

Knochenhauer, Robert John

In many commercial and recreational environments where power is unavailable, there is a need for lightweight, efficient, reasonably priced and quiet power sources that can recharge batteries for various portable devices. The current benchmark device is the Honda EU1000i, a 1000-Watt (peak) generator that weighs only 29 pounds (dry) and has a respectable noise level of 59 dB (at 7 meters) under peak power loading. The intent of this thesis study is to focus on the thermal management of a novel generator design that develops peak power of 500-Watts, weighs in at less than 20 pounds (dry) and has a reasonably low noise level at peak power loading. Through the course of this assessment, two key lessons are learned: • Liquid cooling at this scale is possible, but not practical • Renewable power sources (wind turbines and/or solar panels) are viable alternatives when used in environments that offer suitable conditions.

Low-level rf control of Spallation Neutron Source: System and characterization

NASA Astrophysics Data System (ADS)

Ma, Hengjie; Champion, Mark; Crofford, Mark; Kasemir, Kay-Uwe; Piller, Maurice; Doolittle, Lawrence; Ratti, Alex

2006-03-01

The low-level rf control system currently commissioned throughout the Spallation Neutron Source (SNS) LINAC evolved from three design iterations over 1 yr intensive research and development. Its digital hardware implementation is efficient, and has succeeded in achieving a minimum latency of less than 150 ns which is the key for accomplishing an all-digital feedback control for the full bandwidth. The control bandwidth is analyzed in frequency domain and characterized by testing its transient response. The hardware implementation also includes the provision of a time-shared input channel for a superior phase differential measurement between the cavity field and the reference. A companion cosimulation system for the digital hardware was developed to ensure a reliable long-term supportability. A large effort has also been made in the operation software development for the practical issues such as the process automations, cavity filling, beam loading compensation, and the cavity mechanical resonance suppression.

A hybrid-type quantum random number generator

NASA Astrophysics Data System (ADS)

Hai-Qiang, Ma; Wu, Zhu; Ke-Jin, Wei; Rui-Xue, Li; Hong-Wei, Liu

2016-05-01

This paper proposes a well-performing hybrid-type truly quantum random number generator based on the time interval between two independent single-photon detection signals, which is practical and intuitive, and generates the initial random number sources from a combination of multiple existing random number sources. A time-to-amplitude converter and multichannel analyzer are used for qualitative analysis to demonstrate that each and every step is random. Furthermore, a carefully designed data acquisition system is used to obtain a high-quality random sequence. Our scheme is simple and proves that the random number bit rate can be dramatically increased to satisfy practical requirements. Project supported by the National Natural Science Foundation of China (Grant Nos. 61178010 and 11374042), the Fund of State Key Laboratory of Information Photonics and Optical Communications (Beijing University of Posts and Telecommunications), China, and the Fundamental Research Funds for the Central Universities of China (Grant No. bupt2014TS01).

Flexible and stretchable power sources for wearable electronics

PubMed Central

Zamarayeva, Alla M.; Ostfeld, Aminy E.; Wang, Michael; Duey, Jerica K.; Deckman, Igal; Lechêne, Balthazar P.; Davies, Greg; Steingart, Daniel A.; Arias, Ana Claudia

2017-01-01

Flexible and stretchable power sources represent a key technology for the realization of wearable electronics. Developing flexible and stretchable batteries with mechanical endurance that is on par with commercial standards and offer compliance while retaining safety remains a significant challenge. We present a unique approach that demonstrates mechanically robust, intrinsically safe silver-zinc batteries. This approach uses current collectors with enhanced mechanical design, such as helical springs and serpentines, as a structural support and backbone for all battery components. We show wire-shaped batteries based on helical band springs that are resilient to fatigue and retain electrochemical performance over 17,000 flexure cycles at a 0.5-cm bending radius. Serpentine-shaped batteries can be stretched with tunable degree and directionality while maintaining their specific capacity. Finally, the batteries are integrated, as a wearable device, with a photovoltaic module that enables recharging of the batteries. PMID:28630897

Is White Light the Best Illumination for Palmprint Recognition?

NASA Astrophysics Data System (ADS)

Guo, Zhenhua; Zhang, David; Zhang, Lei

Palmprint as a new biometric has received great research attention in the past decades. It owns many merits, such as robustness, low cost, user friendliness, and high accuracy. Most of the current palmprint recognition systems use an active light to acquire clear palmprint images. Thus, light source is a key component in the system to capture enough of discriminant information for palmprint recognition. To the best of our knowledge, white light is the most widely used light source. However, little work has been done on investigating whether white light is the best illumination for palmprint recognition. In this study, we empirically compared palmprint recognition accuracy using white light and other six different color lights. The experiments on a large database show that white light is not the optimal illumination for palmprint recognition. This finding will be useful to future palmprint recognition system design.

Microcomputer pollution model for civilian airports and Air Force bases. Model description

DOE Office of Scientific and Technical Information (OSTI.GOV)

Segal, H.M.; Hamilton, P.L.

1988-08-01

This is one of three reports describing the Emissions and Dispersion Modeling System (EDMS). EDMS is a complex source emissions/dispersion model for use at civilian airports and Air Force bases. It operates in both a refined and a screening mode and is programmed for an IBM-XT (or compatible) computer. This report--MODEL DESCRIPTION--provides the technical description of the model. It first identifies the key design features of both the emissions (EMISSMOD) and dispersion (GIMM) portions of EDMS. It then describes the type of meteorological information the dispersion model can accept and identifies the manner in which it preprocesses National Climatic Centermore » (NCC) data prior to a refined-model run. The report presents the results of running EDMS on a number of different microcomputers and compares EDMS results with those of comparable models. The appendices elaborate on the information noted above and list the source code.« less

Heavy metal contamination from geothermal sources.

PubMed Central

Sabadell, J E; Axtmann, R C

1975-01-01

Liquid-dominated hydrothermal reservoirs, which contain saline fluids at high temperatures and pressures, have a significant potential for contamination of the environment by heavy metals. The design of the power conversion cycle in a liquid-dominated geothermal plant is a key factor in determining the impact of the installation. Reinjection of the fluid into the reservoir minimizes heavy metal effluents but is routinely practiced at few installations. Binary power cycles with reinjection would provide even cleaner systems but are not yet ready for commercial application. Vapor-dominated systems, which contain superheated steam, have less potential for contamination but are relatively uncommon. Field data on heavy metal effluents from geothermal plants are sparse and confounded by contributions from "natural" sources such as geysers and hot springs which often exist nearby. Insofar as geothermal power supplies are destined to multiply, much work is required on their environmental effects including those caused by heavy metals. PMID:1227849

An airport cargo inspection system based on X-ray and thermal neutron analysis (TNA).

PubMed

Ipe, Nisy E; Akery, A; Ryge, P; Brown, D; Liu, F; Thieu, J; James, B

2005-01-01

A cargo inspection system incorporating a high-resolution X-ray imaging system with a material-specific detection system based on Ancore Corporation's patented thermal neutron analysis (TNA) technology can detect bulk quantities of explosives and drugs concealed in trucks or cargo containers. The TNA process utilises a 252Cf neutron source surrounded by a moderator. The neutron interactions with the inspected object result in strong and unique gamma-ray signals from nitrogen, which is a key ingredient in modern high explosives, and from chlorinated drugs. The TNA computer analyses the gamma-ray signals and automatically determines the presence of explosives or drugs. The radiation source terms and shielding design of the facility are described. For the X-ray generator, the primary beam, leakage radiation, and scattered primary and leakage radiation were considered. For the TNA, the primary neutrons and tunnel scattered neutrons as well as the neutron-capture gamma rays were considered.

Heavy metal contamination from geothermal sources.

PubMed

Sabadell, J E; Axtmann, R C

1975-12-01

Liquid-dominated hydrothermal reservoirs, which contain saline fluids at high temperatures and pressures, have a significant potential for contamination of the environment by heavy metals. The design of the power conversion cycle in a liquid-dominated geothermal plant is a key factor in determining the impact of the installation. Reinjection of the fluid into the reservoir minimizes heavy metal effluents but is routinely practiced at few installations. Binary power cycles with reinjection would provide even cleaner systems but are not yet ready for commercial application. Vapor-dominated systems, which contain superheated steam, have less potential for contamination but are relatively uncommon. Field data on heavy metal effluents from geothermal plants are sparse and confounded by contributions from "natural" sources such as geysers and hot springs which often exist nearby. Insofar as geothermal power supplies are destined to multiply, much work is required on their environmental effects including those caused by heavy metals.

Using experimental design to define boundary manikins.

PubMed

Bertilsson, Erik; Högberg, Dan; Hanson, Lars

2012-01-01

When evaluating human-machine interaction it is central to consider anthropometric diversity to ensure intended accommodation levels. A well-known method is the use of boundary cases where manikins with extreme but likely measurement combinations are derived by mathematical treatment of anthropometric data. The supposition by that method is that the use of these manikins will facilitate accommodation of the expected part of the total, less extreme, population. In literature sources there are differences in how many and in what way these manikins should be defined. A similar field to the boundary case method is the use of experimental design in where relationships between affecting factors of a process is studied by a systematic approach. This paper examines the possibilities to adopt methodology used in experimental design to define a group of manikins. Different experimental designs were adopted to be used together with a confidence region and its axes. The result from the study shows that it is possible to adapt the methodology of experimental design when creating groups of manikins. The size of these groups of manikins depends heavily on the number of key measurements but also on the type of chosen experimental design.

Simulating of the measurement-device independent quantum key distribution with phase randomized general sources

PubMed Central

Wang, Qin; Wang, Xiang-Bin

2014-01-01

We present a model on the simulation of the measurement-device independent quantum key distribution (MDI-QKD) with phase randomized general sources. It can be used to predict experimental observations of a MDI-QKD with linear channel loss, simulating corresponding values for the gains, the error rates in different basis, and also the final key rates. Our model can be applicable to the MDI-QKDs with arbitrary probabilistic mixture of different photon states or using any coding schemes. Therefore, it is useful in characterizing and evaluating the performance of the MDI-QKD protocol, making it a valuable tool in studying the quantum key distributions. PMID:24728000

Investigation of noise sources and propagation in external gear pumps

NASA Astrophysics Data System (ADS)

Opperwall, Timothy J.

Oil hydraulics is widely accepted as the best technology for transmitting power in many engineering applications due to its advantages in power density, control, layout flexibility, and efficiency. Due to these advantages, hydraulic systems are present in many different applications including construction, agriculture, aerospace, automotive, forestry, medical, and manufacturing, just to identify a few. Many of these applications involve the systems in close proximity to human operators and passengers where noise is one of the main constraints to the acceptance and spread of this technology. As a key component in power transfer, displacement machines can be major sources of noise in hydraulic systems. Thus, investigation into the sources of noise and discovering strategies to reduce noise is a key part of applying fluid power systems to a wider range of applications, as well as improving the performance of current hydraulic systems. The present research aims to leverage previous efforts and develop new models and experimental techniques in the topic of noise generation caused by hydrostatic units. This requires challenging and surpassing current accepted methods in the understanding of noise in fluid power systems. This research seeks to expand on the previous experimental and modeling efforts by directly considering the effect that system and component design changes apply on the total sound power and the sound frequency components emitted from displacement machines and the attached lines. The case of external gear pumps is taken as reference for a new model to understand the generation and transmission of noise from the sources out to the environment. The lumped parameter model HYGESim (HYdraulic GEar machine Simulator) was expanded to investigate the dynamic forces on the solid bodies caused by the pump operation and to predict interactions with the attached system. Vibration and sound radiation were then predicted using a combined finite element and boundary element vibro-acoustic model as well as the influence of additional models for system components to better understand the essential problems of noise generation in hydraulic systems. This model is a step forward for the field due to the coupling of an advanced internal model of pump operation coupled to a detailed vibro-acoustic model. Several experimental studies were also completed in order to advance the current science. The first study validated the pump model in terms of outlet pressure ripple prediction through comparison to experimentally measured results for the reference pump as well as prototype pumps designed for low outlet pressure ripple. The second study focused on the air-borne noise through sound pressure and intensity measurements on reference and prototype pumps at steady-state operating conditions. A third study over a wide range of operating speeds and pressures was completed to explore the impact of operating condition and system design to greater detail through measuring noise and vibration in the working fluid, the system structures, and the air. Applying the knowledge gained through experimental and simulation studies has brought new advances in the understanding of the physics of noise generation and propagation in hydraulic components and systems. The focus of the combined simulation and modeling approach is to clearly understand the different contributions from noise sources and surpasses the previous methods that focus on the outlet pressure ripple alone as a source of noise. The application of the new modeling and experimental approach allows for new advances which directly contribute to advancing the science of noise in hydraulic applications and the design of new quieter hydrostatic units and hydraulic systems.

Preamplifiers for non-contact capacitive biopotential measurements*

PubMed Central

Peng, GuoChen; Ignjatovic, Zeljko; Bocko, Mark F.

2014-01-01

Non-contact biopotential sensing is an attractive measurement strategy for a number of health monitoring applications, primarily the ECG and the EEG. In all such applications a key technical challenge is the design of a low-noise trans-impedance preamplifier for the typically low-capacitance, high source impedance sensing electrodes. In this paper, we compare voltage and charge amplifier designs in terms of their common mode rejection ratio, noise performance, and frequency response. Both amplifier types employ the same operational-transconductance amplifier (OTA), which was fabricated in a 0.35um CMOS process. The results show that a charge amplifier configuration has advantages for small electrode-to-subject coupling capacitance values (less than 10 pF - typical of noncontact electrodes) and that the voltage amplifier configuration has advantages for electrode capacitances above 10 pF. PMID:24109979

Design and application of BIM based digital sand table for construction management

NASA Astrophysics Data System (ADS)

Fuquan, JI; Jianqiang, LI; Weijia, LIU

2018-05-01

This paper explores the design and application of BIM based digital sand table for construction management. Aiming at the demands and features of construction management plan for bridge and tunnel engineering, the key functional features of digital sand table should include three-dimensional GIS, model navigation, virtual simulation, information layers, and data exchange, etc. That involving the technology of 3D visualization and 4D virtual simulation of BIM, breakdown structure of BIM model and project data, multi-dimensional information layers, and multi-source data acquisition and interaction. Totally, the digital sand table is a visual and virtual engineering information integrated terminal, under the unified data standard system. Also, the applications shall contain visual constructing scheme, virtual constructing schedule, and monitoring of construction, etc. Finally, the applicability of several basic software to the digital sand table is analyzed.

Transport systems research vehicle color display system operations manual

NASA Technical Reports Server (NTRS)

Easley, Wesley C.; Johnson, Larry E.

1989-01-01

A recent upgrade of the Transport Systems Research Vehicle operated by the Advanced Transport Operating Systems Program Office at the NASA Langley Research Center has resulted in an all-glass panel in the research flight deck. Eight ARINC-D size CRT color displays make up the panel. A major goal of the display upgrade effort was ease of operation and maintenance of the hardware while maintaining versatility needed for flight research. Software is the key to this required versatility and will be the area demanding the most detailed technical design expertise. This document is is intended to serve as a single source of quick reference information needed for routine operation and system level maintenance. Detailed maintenance and modification of the display system will require specific design documentation and must be accomplished by individuals with specialized knowledge and experience.

Update on Development of Mesh Generation Algorithms in MeshKit

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jain, Rajeev; Vanderzee, Evan; Mahadevan, Vijay

2015-09-30

MeshKit uses a graph-based design for coding all its meshing algorithms, which includes the Reactor Geometry (and mesh) Generation (RGG) algorithms. This report highlights the developmental updates of all the algorithms, results and future work. Parallel versions of algorithms, documentation and performance results are reported. RGG GUI design was updated to incorporate new features requested by the users; boundary layer generation and parallel RGG support were added to the GUI. Key contributions to the release, upgrade and maintenance of other SIGMA1 libraries (CGM and MOAB) were made. Several fundamental meshing algorithms for creating a robust parallel meshing pipeline in MeshKitmore » are under development. Results and current status of automated, open-source and high quality nuclear reactor assembly mesh generation algorithms such as trimesher, quadmesher, interval matching and multi-sweeper are reported.« less

The Development of a Simulator System and Hardware Test Bed for Deep Space X-Ray Navigation

NASA Astrophysics Data System (ADS)

Doyle, Patrick T.

2013-03-01

Currently, there is a considerable interest in developing technologies that will allow using photon measurements from celestial x-ray sources for deep space navigation. The impetus for this is that many envisioned future space missions will require spacecraft to have autonomous navigation capabilities. For missions close to Earth, Global Navigation Satellite Systems (GNSS) such as GPS are readily available for use, but for missions far from Earth, other alternatives must be provided. While existing systems such as the Deep Space Network (DSN) can be used, latencies associated with servicing a fleet of vehicles may not be compatible with some autonomous operations requiring timely updates of their navigation solution. Because of their somewhat predictable emissions, pulsars are the ideal candidates for x-ray sources that can be used to provide key parameters for navigation. Algorithms and simulation tools that will enable designing and analyzing x-ray navigation concepts are presented. The development of a compact x-ray detector system is pivotal to the eventual deployment of such navigation systems. Therefore, results of a high altitude balloon test to evaluate the design of a compact x-ray detector system are described as well.

The Advanced Gamma-ray Imaging System (AGIS): Next-generation Cherenkov telescopes array.

NASA Astrophysics Data System (ADS)

Vassiliev, Vladimir; AGIS Collaboration

2010-03-01

AGIS is a concept for a next-generation ground-based gamma-ray observatory in the energy range from 50 GeV to 200 TeV. AGIS is being designed to have significantly improved sensitivity, angular resolution, and reliability of operation relative to the present generation instruments such as VERITAS and H.E.S.S. The novel technologies of AGIS are expected to enable great advances in the understanding of the populations and physics of sources of high-energy gamma rays in the Milky Way (e.g. SNR, X-ray binaries, dense molecular clouds) and outside the Galaxy (e.g. AGN, GRBs, galaxy clusters, and star-forming galaxies). AGIS will complement and extend the results now being obtained in the GeV range with the Fermi mission providing wide energy coverage, superior angular resolution, and sensitivity to variability on short time scales. AGIS will be a key instrument for identifying and characterizing Fermi LAT sources. In this submission we outline the status of the development of AGIS project, design concept, and principal technologies. As illustrations of the scientific capabilities of AGIS, we review its potential to indirectly search for dark matter and measure cosmological magnetic fields.

Seaworthy Quantum Key Distribution Design and Validation (SEAKEY)

DTIC Science & Technology

2016-03-10

Contractor Address: 10 Moulton Street, Cambridge, MA 02138 Title of the Project: Seaworthy Quantum Key Distribution Design and Validation (SEAKEY...Technologies Kathryn Carson Program Manager Quantum Information Processing 2 | P a g e Approved for public release; distribution is...we have continued work calculating the key rates achievable parametrically with receiver performance. In addition, we describe the initial designs

Optically-pumped spin-exchange polarized electron source

NASA Astrophysics Data System (ADS)

Pirbhai, Munir Hussein

Polarized electron beams are an indispensable probe of spin-dependent phenomena in fields of atomic and molecular physics, magnetism and biophysics. While their uses have become widespread, the standard source based on negative electron affinity gallium arsenide (GaAs) remains technically complicated. This has hindered progress on many experiments involving spin-polarized electrons, especially those using target gas loads, which tend to adversely affect the performance of GaAs sources. A robust system based on an alternative way to make polarized electron beams has been devised in this study, which builds on previous work done in our lab. It involves spin-exchange collisions between free, unpolarized electrons and oriented rubidium atoms in the presence of a quenching gas. This system has less stringent vacuum requirements than those of GaAs sources, and is capable of operating in background pressures of ~1mTorr. Beams with ~24% polarization and 4μA of current have been recorded, which is comparable to the performance obtained with the earlier version built in our lab. The present system is however not as unstable as in the previous work, and has the potential to be developed into a "turn-key" source of polarized electron beams. It has also allowed us to undertake a study to find factors which affect the beam polarization in this scheme of producing polarized electrons. Such knowledge will help us to design better optically-pumped spin-exchange polarized electron sources.

A Key Pre-Distribution Scheme Based on µ-PBIBD for Enhancing Resilience in Wireless Sensor Networks.

PubMed

Yuan, Qi; Ma, Chunguang; Yu, Haitao; Bian, Xuefen

2018-05-12

Many key pre-distribution (KPD) schemes based on combinatorial design were proposed for secure communication of wireless sensor networks (WSNs). Due to complexity of constructing the combinatorial design, it is infeasible to generate key rings using the corresponding combinatorial design in large scale deployment of WSNs. In this paper, we present a definition of new combinatorial design, termed “µ-partially balanced incomplete block design (µ-PBIBD)”, which is a refinement of partially balanced incomplete block design (PBIBD), and then describe a 2-D construction of µ-PBIBD which is mapped to KPD in WSNs. Our approach is of simple construction which provides a strong key connectivity and a poor network resilience. To improve the network resilience of KPD based on 2-D µ-PBIBD, we propose a KPD scheme based on 3-D Ex-µ-PBIBD which is a construction of µ-PBIBD from 2-D space to 3-D space. Ex-µ-PBIBD KPD scheme improves network scalability and resilience while has better key connectivity. Theoretical analysis and comparison with the related schemes show that key pre-distribution scheme based on Ex-µ-PBIBD provides high network resilience and better key scalability, while it achieves a trade-off between network resilience and network connectivity.

A Key Pre-Distribution Scheme Based on µ-PBIBD for Enhancing Resilience in Wireless Sensor Networks

PubMed Central

Yuan, Qi; Ma, Chunguang; Yu, Haitao; Bian, Xuefen

2018-01-01

Many key pre-distribution (KPD) schemes based on combinatorial design were proposed for secure communication of wireless sensor networks (WSNs). Due to complexity of constructing the combinatorial design, it is infeasible to generate key rings using the corresponding combinatorial design in large scale deployment of WSNs. In this paper, we present a definition of new combinatorial design, termed “µ-partially balanced incomplete block design (µ-PBIBD)”, which is a refinement of partially balanced incomplete block design (PBIBD), and then describe a 2-D construction of µ-PBIBD which is mapped to KPD in WSNs. Our approach is of simple construction which provides a strong key connectivity and a poor network resilience. To improve the network resilience of KPD based on 2-D µ-PBIBD, we propose a KPD scheme based on 3-D Ex-µ-PBIBD which is a construction of µ-PBIBD from 2-D space to 3-D space. Ex-µ-PBIBD KPD scheme improves network scalability and resilience while has better key connectivity. Theoretical analysis and comparison with the related schemes show that key pre-distribution scheme based on Ex-µ-PBIBD provides high network resilience and better key scalability, while it achieves a trade-off between network resilience and network connectivity. PMID:29757244

Ergonomics and sustainability in the design of everyday use products.

PubMed

Tosi, Francesca

2012-01-01

The relationship between Ergonomics and Design is a key element in the sustainability project, as well as in many other areas of experimental design. In the Design for Sustainability field, Ergonomics is a strategic factor for design culture innovation, providing designers with the necessary knowledge and skills regarding human characteristics and capabilities, as well as user needs and desires during use and interaction with products in work activities and everyday life. Ergonomics is also a strategic innovative factor in design development and manufacturing processes. In fact, ergonomics provides a methodological approach in user-product interaction evaluation processes through the use of participatory design and survey methods, user trials, direct observation, savings and resource conservation, etc.On the other hand, design offers solutions able to interpret user needs and expectations, at the same time suggesting new behaviors and lifestyles.In Design for Sustainability, the ergonomic and user-centered approach contributes greatly to lifestyles and innovative use of products--making it possible to understand and interpret real people needs and expectations in their everyday actions and behavior.New consumption patterns, new awareness of lifestyles, energy source consumption, purchasing methods and consumption style etc. can be supported by design innovation, responding to expressed and unexpressed user needs. With this in mind, the ergonomic approach represents the starting point for design choices and at the same time, a tool for assessing their appropriateness and effectiveness.

Power supply system for negative ion source at IPR

NASA Astrophysics Data System (ADS)

Gahlaut, Agrajit; Sonara, Jashwant; Parmar, K. G.; Soni, Jignesh; Bandyopadhyay, M.; Singh, Mahendrajit; Bansal, Gourab; Pandya, Kaushal; Chakraborty, Arun

2010-02-01

The first step in the Indian program on negative ion beams is the setting up of Negative ion Experimental Assembly - RF based, where 100 kW of RF power shall be coupled to a plasma source producing plasma of density ~5 × 1012 cm-3, from which ~ 10 A of negative ion beam shall be produced and accelerated to 35 kV, through an electrostatic ion accelerator. The experimental system is modelled similar to the RF based negative ion source, BATMAN presently operating at IPP, Garching, Germany. The mechanical system for Negative Ion Source Assembly is close to the IPP source, remaining systems are designed and procured principally from indigenous sources, keeping the IPP configuration as a base line. High voltage (HV) and low voltage (LV) power supplies are two key constituents of the experimental setup. The HV power supplies for extraction and acceleration are rated for high voltage (~15 to 35kV), and high current (~ 15 to 35A). Other attributes are, fast rate of voltage rise (< 5ms), good regulation (< ±1%), low ripple (< ±2%), isolation (~50kV), low energy content (< 10J) and fast cut-off (< 100μs). The low voltage (LV) supplies required for biasing and providing heating power to the Cesium oven and the plasma grids; have attributes of low ripple, high stability, fast and precise regulation, programmability and remote operation. These power supplies are also equipped with over-voltage, over-current and current limit (CC Mode) protections. Fault diagnostics, to distinguish abnormal rise in currents (breakdown faults) with over-currents is enabled using fast response breakdown and over-current protection scheme. To restrict the fault energy deposited on the ion source, specially designed snubbers are implemented in each (extraction and acceleration) high voltage path to swap the surge energy. Moreover, the monitoring status and control signals from these power supplies are required to be electrically (~ 50kV) isolated from the system. The paper shall present the design basis, topology selection, manufacturing, testing, commissioning, integration and control strategy of these HVPS. A complete power interconnection scheme, which includes all protective devices and measuring devices, low & high voltage power supplies, monitoring and control signals etc. shall also be discussed. The paper also discusses the protocols involved in grounding and shielding, particularly in operating the system in RF environment.

Biased three-intensity decoy-state scheme on the measurement-device-independent quantum key distribution using heralded single-photon sources.

PubMed

Zhang, Chun-Hui; Zhang, Chun-Mei; Guo, Guang-Can; Wang, Qin

2018-02-19

At present, most of the measurement-device-independent quantum key distributions (MDI-QKD) are based on weak coherent sources and limited in the transmission distance under realistic experimental conditions, e.g., considering the finite-size-key effects. Hence in this paper, we propose a new biased decoy-state scheme using heralded single-photon sources for the three-intensity MDI-QKD, where we prepare the decoy pulses only in X basis and adopt both the collective constraints and joint parameter estimation techniques. Compared with former schemes with WCS or HSPS, after implementing full parameter optimizations, our scheme gives distinct reduced quantum bit error rate in the X basis and thus show excellent performance, especially when the data size is relatively small.

Passive measurement-device-independent quantum key distribution with orbital angular momentum and pulse position modulation

NASA Astrophysics Data System (ADS)

Wang, Lian; Zhou, Yuan-yuan; Zhou, Xue-jun; Chen, Xiao

2018-03-01

Based on the orbital angular momentum and pulse position modulation, we present a novel passive measurement-device-independent quantum key distribution (MDI-QKD) scheme with the two-mode source. Combining with the tight bounds of the yield and error rate of single-photon pairs given in our paper, we conduct performance analysis on the scheme with heralded single-photon source. The numerical simulations show that the performance of our scheme is significantly superior to the traditional MDI-QKD in the error rate, key generation rate and secure transmission distance, since the application of orbital angular momentum and pulse position modulation can exclude the basis-dependent flaw and increase the information content for each single photon. Moreover, the performance is improved with the rise of the frame length. Therefore, our scheme, without intensity modulation, avoids the source side channels and enhances the key generation rate. It has greatly utility value in the MDI-QKD setups.

Single-random-phase holographic encryption of images

NASA Astrophysics Data System (ADS)

Tsang, P. W. M.

2017-02-01

In this paper, a method is proposed for encrypting an optical image onto a phase-only hologram, utilizing a single random phase mask as the private encryption key. The encryption process can be divided into 3 stages. First the source image to be encrypted is scaled in size, and pasted onto an arbitrary position in a larger global image. The remaining areas of the global image that are not occupied by the source image could be filled with randomly generated contents. As such, the global image as a whole is very different from the source image, but at the same time the visual quality of the source image is preserved. Second, a digital Fresnel hologram is generated from the new image, and converted into a phase-only hologram based on bi-directional error diffusion. In the final stage, a fixed random phase mask is added to the phase-only hologram as the private encryption key. In the decryption process, the global image together with the source image it contained, can be reconstructed from the phase-only hologram if it is overlaid with the correct decryption key. The proposed method is highly resistant to different forms of Plain-Text-Attacks, which are commonly used to deduce the encryption key in existing holographic encryption process. In addition, both the encryption and the decryption processes are simple and easy to implement.

Design and Development of nEMoS, an All-in-One, Low-Cost, Web-Connected and 3D-Printed Device for Environmental Analysis

PubMed Central

Salamone, Francesco; Belussi, Lorenzo; Danza, Ludovico; Ghellere, Matteo; Meroni, Italo

2015-01-01

The Indoor Environmental Quality (IEQ) refers to the quality of the environment in relation to the health and well-being of the occupants. It is a holistic concept, which considers several categories, each related to a specific environmental parameter. This article describes a low-cost and open-source hardware architecture able to detect the indoor variables necessary for the IEQ calculation as an alternative to the traditional hardware used for this purpose. The system consists of some sensors and an Arduino board. One of the key strengths of Arduino is the possibility it affords of loading the script into the board’s memory and letting it run without interfacing with computers, thus granting complete independence, portability and accuracy. Recent works have demonstrated that the cost of scientific equipment can be reduced by applying open-source principles to their design using a combination of the Arduino platform and a 3D printer. The evolution of the 3D printer has provided a new means of open design capable of accelerating self-directed development. The proposed nano Environmental Monitoring System (nEMoS) instrument is shown to have good reliability and it provides the foundation for a more critical approach to the use of professional sensors as well as for conceiving new scenarios and potential applications. PMID:26053749

Challenges and opportunities in the design and construction of a GIS-based emission inventory infrastructure for the Niger Delta region of Nigeria.

PubMed

Fagbeja, Mofoluso A; Hill, Jennifer L; Chatterton, Tim J; Longhurst, James W S; Akpokodje, Joseph E; Agbaje, Ganiy I; Halilu, Shaba A

2017-03-01

Environmental monitoring in middle- and low-income countries is hampered by many factors which include enactment and enforcement of legislations; deficiencies in environmental data reporting and documentation; inconsistent, incomplete and unverifiable data; a lack of access to data; and technical expertise. This paper describes the processes undertaken and the major challenges encountered in the construction of the first Niger Delta Emission Inventory (NDEI) for criteria air pollutants and CO 2 released from the anthropogenic activities in the region. This study focused on using publicly available government and research data. The NDEI has been designed to provide a Geographic Information System-based component of an air quality and carbon management framework. The NDEI infrastructure was designed and constructed at 1-, 10- and 20-km grid resolutions for point, line and area sources using industry standard processes and emission factors derived from activities similar to those in the Niger Delta. Due to inadequate, incomplete, potentially inaccurate and unavailable data, the infrastructure was populated with data based on a series of best possible assumptions for key emission sources. This produces outputs with variable levels of certainty, which also highlights the critical challenges in the estimation of emissions from a developing country. However, the infrastructure is functional and has the ability to produce spatially resolved emission estimates.

Design and development of nEMoS, an all-in-one, low-cost, web-connected and 3D-printed device for environmental analysis.

PubMed

Salamone, Francesco; Belussi, Lorenzo; Danza, Ludovico; Ghellere, Matteo; Meroni, Italo

2015-06-04

The Indoor Environmental Quality (IEQ) refers to the quality of the environment in relation to the health and well-being of the occupants. It is a holistic concept, which considers several categories, each related to a specific environmental parameter. This article describes a low-cost and open-source hardware architecture able to detect the indoor variables necessary for the IEQ calculation as an alternative to the traditional hardware used for this purpose. The system consists of some sensors and an Arduino board. One of the key strengths of Arduino is the possibility it affords of loading the script into the board's memory and letting it run without interfacing with computers, thus granting complete independence, portability and accuracy. Recent works have demonstrated that the cost of scientific equipment can be reduced by applying open-source principles to their design using a combination of the Arduino platform and a 3D printer. The evolution of the 3D printer has provided a new means of open design capable of accelerating self-directed development. The proposed nano Environmental Monitoring System (nEMoS) instrument is shown to have good reliability and it provides the foundation for a more critical approach to the use of professional sensors as well as for conceiving new scenarios and potential applications.

Effects of Design Variants in Lower-Limb Prostheses on Gait Synergy

PubMed Central

Pitkin, Mark R.

2016-01-01

A lower-limb prosthesis is the mechanical device with which an amputee’s residual limb interacts with the walking surface. The pressure and shear forces that affect the residuum due to prosthesis use are the sources of pain, residual-limb skin problems and gait deviations. Direct approaches to reducing these problems include improving fit, alignment technique and socket design as well as increasing cushioning with socket liners. A summary of typical malalignments and their consequences is presented. The malalignments are considered sources of excessive moments applied to the residuum, which simplifies the analysis of a patient’s gait. A better design of prosthetic joints could improve prosthetic gait. This article addresses the key mechanical parameter of prosthetic joints, namely the dependence “moment of resistance/angle of deflection.” A mathematical model has been developed that links stresses on the residuum in transtibial amputees with the moment of resistance in the prosthetic ankle at the critical gait phases. Analysis of the model yields a substantial decrease in stresses on the residuum during the most demanding, load-bearing phase of stance if the moment of resistance in the ankle is similar to that seen in the biological ankle joint. Gait study shows use of the experimental rolling-joint prosthetic foot more closely simulates normal gait synergy than the SACH foot. PMID:27087763

Survey of Ambient Air Pollution Health Risk Assessment Tools.

PubMed

Anenberg, Susan C; Belova, Anna; Brandt, Jørgen; Fann, Neal; Greco, Sue; Guttikunda, Sarath; Heroux, Marie-Eve; Hurley, Fintan; Krzyzanowski, Michal; Medina, Sylvia; Miller, Brian; Pandey, Kiran; Roos, Joachim; Van Dingenen, Rita

2016-09-01

Designing air quality policies that improve public health can benefit from information about air pollution health risks and impacts, which include respiratory and cardiovascular diseases and premature death. Several computer-based tools help automate air pollution health impact assessments and are being used for a variety of contexts. Expanding information gathered for a May 2014 World Health Organization expert meeting, we survey 12 multinational air pollution health impact assessment tools, categorize them according to key technical and operational characteristics, and identify limitations and challenges. Key characteristics include spatial resolution, pollutants and health effect outcomes evaluated, and method for characterizing population exposure, as well as tool format, accessibility, complexity, and degree of peer review and application in policy contexts. While many of the tools use common data sources for concentration-response associations, population, and baseline mortality rates, they vary in the exposure information source, format, and degree of technical complexity. We find that there is an important tradeoff between technical refinement and accessibility for a broad range of applications. Analysts should apply tools that provide the appropriate geographic scope, resolution, and maximum degree of technical rigor for the intended assessment, within resources constraints. A systematic intercomparison of the tools' inputs, assumptions, calculations, and results would be helpful to determine the appropriateness of each for different types of assessment. Future work would benefit from accounting for multiple uncertainty sources and integrating ambient air pollution health impact assessment tools with those addressing other related health risks (e.g., smoking, indoor pollution, climate change, vehicle accidents, physical activity). © 2016 Society for Risk Analysis.

Ultra-low output impedance RF power amplifier for parallel excitation.

PubMed

Chu, Xu; Yang, Xing; Liu, Yunfeng; Sabate, Juan; Zhu, Yudong

2009-04-01

Inductive coupling between coil elements of a transmit array is one of the key challenges faced by parallel RF transmission. An ultra-low output impedance RF power amplifier (PA) concept was introduced to address this challenge. In an example implementation, an output-matching network was designed to transform the drain-source impedance of the metallic oxide semiconductor field effect transistor (MOSFET) into a very low value for suppressing interelement coupling effect, and meanwhile, to match the input impedance of the coil to the optimum load of the MOSFET for maximizing the available output power. Two prototype amplifiers with 500-W output rating were developed accordingly, and were further evaluated with a transmit array in phantom experiments. Compared to the conventional 50-Omega sources, the new approach exhibited considerable effectiveness suppressing the effects of interelement coupling. The experiments further indicated that the isolation performance was comparable to that achieved by optimized overlap decoupling. The new approach, benefiting from a distinctive current-source characteristic, also exhibited a superior robustness against load variation. Feasibility of the new approach in high-field MR was demonstrated on a 3T clinical scanner.

Design of a patient-centered, multi-institutional healthcare information network using peer-to-peer communication in a highly distributed architecture.

PubMed

Geissbuhler, Antoine; Spahni, Stéphane; Assimacopoulos, André; Raetzo, Marc-André; Gobet, Gérard

2004-01-01

to design a community healthcare information network for all 450,000 citizen in the State of Geneva, Switzerland, connecting public and private healthcare professionals. Requirements include the decentralized storage of information at the source of its production, the creation of a virtual patient record at the time of the consultation, the control by the patient of the access rights to the information, and the interoperability with other similar networks at the national and european level. a participative approach and real-world pilot projects are used to design, test and validate key components of the network, including its technical architecture and the strategy for the management of access rights by the patients. a distributed architecture using peer-to-peer communication of information mediators can implement the various requirements while limiting to an absolute minimum the amount of centralized information. Access control can be managed by the patient with the help of a medical information mediator, the physician of trust.

Neuroesthetics and healthcare design.

PubMed

Nanda, Upali; Pati, Debajyoti; McCurry, Katie

2009-01-01

While there is a growing consciousness about the importance of visually pleasing environments in healthcare design, little is known about the key underlying mechanisms that enable aesthetics to play an instrumental role in the caregiving process. Hence it is often one of the first items to be value engineered. Aesthetics has (rightfully) been provided preferential consideration in such pleasure settings such as museums and recreational facilities; but in healthcare settings it is often considered expendable. Should it be? In this paper the authors share evidence that visual stimuli undergo an aesthetic evaluation process in the human brain by default, even when not prompted; that responses to visual stimuli may be immediate and emotional; and that aesthetics can be a source of pleasure, a fundamental perceptual reward that can help mitigate the stress of a healthcare environment. The authors also provide examples of studies that address the role of specific visual elements and visual principles in aesthetic evaluations and emotional responses. Finally, they discuss the implications of these findings for the design of art and architecture in healthcare.

A passively tunable acoustic metamaterial lens for selective ultrasonic excitation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhu, H.; Semperlotti, F., E-mail: Fabio.Semperlotti.1@nd.edu

2014-09-07

In this paper, we present an approach to ultrasonic beam-forming and beam-steering in structures based on the concept of embedded acoustic metamaterial lenses. The lens design exploits the principle of acoustic drop-channel that enables the dynamic coupling of multiple ultrasonic waveguides at selected frequencies. In contrast with currently available technology, the embedded lens allows exploiting the host structure as a key component of the transducer system therefore enabling directional excitation by means of a single ultrasonic transducer. The design and the performance of the lens are numerically investigated by using Plane Wave Expansion and Finite Difference Time Domain techniques appliedmore » to bulk structures. Then, the design is experimentally validated on a thin aluminum plate waveguide where the lens is implemented by through-holes. The dynamic response of the embedded lens is estimated by reconstructing, via Laser Vibrometry, the velocity field induced by a single source located at the center of the lens.« less

Sourcing in the Air Force: An Optimization Approach

DTIC Science & Technology

2009-09-01

quality supplies and services at the lowest cost ( Gabbard , 2004). The commodity sourcing strategy focuses on developing a specific sourcing strategy...Springer Series in Operations Research. New York: Springer-Verlag. Gabbard , E.G. (2004, April). Strategic sourcing: Critical elements and keys to success

Seaworthy Quantum Key Distribution Design and Validation (SEAKEY)

DTIC Science & Technology

2015-05-27

Address: 10 Moulton Street, Cambridge, MA 02138 Title of the Project: Seaworthy Quantum Key Distribution Design and Validation (SEAKEY...Technologies Kathryn Carson Program Manager Quantum Information Processing Report Documentation Page Form ApprovedOMB No. 0704-0188 Public...2016 4. TITLE AND SUBTITLE Seaworthy Quantum Key Distribution Design and Validation (SEAKEY) 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM

Source-Water Protection and Water-Quality Investigations in the Cambridge, Massachusetts, Drinking-Water Supply System

USGS Publications Warehouse

Waldron, Marcus C.; Norton, Chip; MacDonald, Timothy W.D.

1998-01-01

Introduction The Cambridge Water Department (CWD) supplies about 15 million gallons of water each day to more than 95,000 customers in the City of Cambridge, Massachusetts. Most of this water is obtained from a system of reservoirs located in Cambridge and in parts of five other suburban-Boston communities. The drainage basin that contributes water to these reservoirs includes several potential sources of drinking-water contaminants, including major highways, secondary roads, areas of commercial and industrial development, and suburban residential tracts. The CWD is implementing a comprehensive Source-Water Protection Plan to ensure that the highest quality water is delivered to the treatment plant. A key element of this plan is a program that combines systematic monitoring of the drainage basin with detailed investigations of the effects of nonpoint-source contaminants, such as highway-deicing chemicals, nutrients, oxygen-demanding organic compounds, bacteria, and trace metals arising from stormwater runoff. The U.S. Geological Survey (USGS) is working with the CWD and the Massachusetts Highway Department (MassHighway) to develop a better understanding of the sources, transport, and fate of many of these contaminants. This Fact Sheet describes source-water protection and water-quality investigations currently underway in the Cambridge drinking-water supply system. The investigations are designed to complement a national effort by the USGS to provide water suppliers and regulatory agencies with information on the vulnerability of water supplies and the movement and fate of source-water contaminants.

The Next Generation of HLA Image Products

NASA Astrophysics Data System (ADS)

Gaffney, N. I.; Casertano, S.; Ferguson, B.

2012-09-01

We present the re-engineered pipeline based on existing and improved algorithms with the aim of improving processing quality, cross-instrument portability, data flow management, and software maintenance. The Hubble Legacy Archive (HLA) is a project to add value to the Hubble Space Telescope data archive by producing and delivering science-ready drizzled data products and source lists derived from these products. Initially, ACS, NICMOS, and WFCP2 data were combined using instrument-specific pipelines based on scripts developed to process the ACS GOODS data and a separate set of scripts to generate source extractor and DAOPhot source lists. The new pipeline, initially designed for WFC3 data, isolates instrument-specific processing and is easily extendable to other instruments and to generating wide-area mosaics. Significant improvements have been made in image combination using improved alignment, source detection, and background equalization routines. It integrates improved alignment procedures, better noise model, and source list generation within a single code base. Wherever practical, PyRAF based routines have been replaced with non-IRAF based python libraries (e.g. NumPy and PyFITS). The data formats have been modified to handle better and more consistent propagation of information from individual exposures to the combined products. A new exposure layer stores the effective exposure time for each pixel in the sky which is key in properly interpreting combined images from diverse data that were not initially planned to be mosaiced. We worked to improve the validity of the metadata within our FITS headers for these products relative to standard IRAF/PyRAF processing. Any keywords that pertain to individual exposures have been removed from the primary and extension headers and placed in a table extension for more direct and efficient perusal. This mechanism also allows for more detailed information on the processing of individual images to be stored and propagated providing a more hierarchical metadata storage system than key value pair FITS headers provide. In this poster we will discuss the changes to the pipeline processing and source list generation and the lessons learned which may be applicable to other archive projects as well as discuss our new metadata curation and preservation process.

SAFE: SPARQL Federation over RDF Data Cubes with Access Control.

PubMed

Khan, Yasar; Saleem, Muhammad; Mehdi, Muntazir; Hogan, Aidan; Mehmood, Qaiser; Rebholz-Schuhmann, Dietrich; Sahay, Ratnesh

2017-02-01

Several query federation engines have been proposed for accessing public Linked Open Data sources. However, in many domains, resources are sensitive and access to these resources is tightly controlled by stakeholders; consequently, privacy is a major concern when federating queries over such datasets. In the Healthcare and Life Sciences (HCLS) domain real-world datasets contain sensitive statistical information: strict ownership is granted to individuals working in hospitals, research labs, clinical trial organisers, etc. Therefore, the legal and ethical concerns on (i) preserving the anonymity of patients (or clinical subjects); and (ii) respecting data ownership through access control; are key challenges faced by the data analytics community working within the HCLS domain. Likewise statistical data play a key role in the domain, where the RDF Data Cube Vocabulary has been proposed as a standard format to enable the exchange of such data. However, to the best of our knowledge, no existing approach has looked to optimise federated queries over such statistical data. We present SAFE: a query federation engine that enables policy-aware access to sensitive statistical datasets represented as RDF data cubes. SAFE is designed specifically to query statistical RDF data cubes in a distributed setting, where access control is coupled with source selection, user profiles and their access rights. SAFE proposes a join-aware source selection method that avoids wasteful requests to irrelevant and unauthorised data sources. In order to preserve anonymity and enforce stricter access control, SAFE's indexing system does not hold any data instances-it stores only predicates and endpoints. The resulting data summary has a significantly lower index generation time and size compared to existing engines, which allows for faster updates when sources change. We validate the performance of the system with experiments over real-world datasets provided by three clinical organisations as well as legacy linked datasets. We show that SAFE enables granular graph-level access control over distributed clinical RDF data cubes and efficiently reduces the source selection and overall query execution time when compared with general-purpose SPARQL query federation engines in the targeted setting.

Livermore Big Artificial Neural Network Toolkit

DOE Office of Scientific and Technical Information (OSTI.GOV)

Essen, Brian Van; Jacobs, Sam; Kim, Hyojin

2016-07-01

LBANN is a toolkit that is designed to train artificial neural networks efficiently on high performance computing architectures. It is optimized to take advantages of key High Performance Computing features to accelerate neural network training. Specifically it is optimized for low-latency, high bandwidth interconnects, node-local NVRAM, node-local GPU accelerators, and high bandwidth parallel file systems. It is built on top of the open source Elemental distributed-memory dense and spars-direct linear algebra and optimization library that is released under the BSD license. The algorithms contained within LBANN are drawn from the academic literature and implemented to work within a distributed-memory framework.

Optical guidance vidicon test program

NASA Technical Reports Server (NTRS)

Eiseman, A. R.; Stanton, R. H.; Voge, C. C.

1976-01-01

A laboratory and field test program was conducted to quantify the optical navigation parameters of the Mariner vidicons. A scene simulator and a camera were designed and built for vidicon tests under a wide variety of conditions. Laboratory tests characterized error sources important to the optical navigation process and field tests verified star sensitivity and characterized comet optical guidance parameters. The equipment, tests and data reduction techniques used are described. Key test results are listed. A substantial increase in the understanding of the use of selenium vidicons as detectors for spacecraft optical guidance was achieved, indicating a reduction in residual offset errors by a factor of two to four to the single pixel level.

Laser system development for gravitational-wave interferometry in space

NASA Astrophysics Data System (ADS)

Numata, Kenji; Yu, Anthony W.; Camp, Jordan B.; Krainak, Michael A.

2018-02-01

A highly stable and robust laser system is a key component of the space-based Laser Interferometer Space Antenna (LISA) mission, which is designed to detect gravitational waves from various astronomical sources. The baseline architecture for the LISA laser consists of a low-power, low-noise Nd:YAG non-planar ring oscillator (NPRO) followed by a diode-pumped Yb-fiber amplifier with 2 W output. We are developing such laser system at the NASA Goddard Space Flight Center (GSFC), as well as investigating other laser options. In this paper, we will describe our progress to date and plans to demonstrate a technology readiness level (TRL) 6 LISA laser system.

Light collection and pulse-shape discrimination in elongated scintillator cells for the PROSPECT reactor antineutrino experiment

NASA Astrophysics Data System (ADS)

Ashenfelter, J.; Balantekin, B.; Band, H. R.; Barclay, G.; Bass, C. D.; Berish, D.; Bowden, N. S.; Bowes, A.; Brodsky, J. P.; Bryan, C. D.; Cherwinka, J. J.; Chu, R.; Classen, T.; Commeford, K.; Davee, D.; Dean, D.; Deichert, G.; Diwan, M. V.; Dolinski, M. J.; Dolph, J.; Dwyer, D. A.; Gaison, J. K.; Galindo-Uribarri, A.; Gilje, K.; Glenn, A.; Goddard, B. W.; Green, M.; Han, K.; Hans, S.; Heeger, K. M.; Heffron, B.; Jaffe, D. E.; Langford, T. J.; Littlejohn, B. R.; Martinez Caicedo, D. A.; McKeown, R. D.; Mendenhall, M. P.; Mueller, P.; Mumm, H. P.; Napolitano, J.; Neilson, R.; Norcini, D.; Pushin, D.; Qian, X.; Romero, E.; Rosero, R.; Saldana, L.; Seilhan, B. S.; Sharma, R.; Sheets, S.; Stemen, N. T.; Surukuchi, P. T.; Varner, R. L.; Viren, B.; Wang, W.; White, B.; White, C.; Wilhelmi, J.; Williams, C.; Wise, T.; Yao, H.; Yeh, M.; Yen, Y. R.; Zangakis, G.; Zhang, C.; Zhang, X.

2015-11-01

A meter-long, 23-liter EJ-309 liquid scintillator detector has been constructed to study the light collection and pulse-shape discrimination performance of elongated scintillator cells for the PROSPECT reactor antineutrino experiment. The magnitude and uniformity of light collection and neutron-gamma discrimination power in the energy range of antineutrino inverse beta decay products have been studied using gamma and spontaneous fission calibration sources deployed along the cell axis. We also study neutron-gamma discrimination and light collection abilities for differing PMT and reflector configurations. Key design features for optimizing MeV-scale response and background rejection capabilities are identified.

Integrative structure modeling with the Integrative Modeling Platform.

PubMed

Webb, Benjamin; Viswanath, Shruthi; Bonomi, Massimiliano; Pellarin, Riccardo; Greenberg, Charles H; Saltzberg, Daniel; Sali, Andrej

2018-01-01

Building models of a biological system that are consistent with the myriad data available is one of the key challenges in biology. Modeling the structure and dynamics of macromolecular assemblies, for example, can give insights into how biological systems work, evolved, might be controlled, and even designed. Integrative structure modeling casts the building of structural models as a computational optimization problem, for which information about the assembly is encoded into a scoring function that evaluates candidate models. Here, we describe our open source software suite for integrative structure modeling, Integrative Modeling Platform (https://integrativemodeling.org), and demonstrate its use. © 2017 The Protein Society.

BeadArray Expression Analysis Using Bioconductor

PubMed Central

Ritchie, Matthew E.; Dunning, Mark J.; Smith, Mike L.; Shi, Wei; Lynch, Andy G.

2011-01-01

Illumina whole-genome expression BeadArrays are a popular choice in gene profiling studies. Aside from the vendor-provided software tools for analyzing BeadArray expression data (GenomeStudio/BeadStudio), there exists a comprehensive set of open-source analysis tools in the Bioconductor project, many of which have been tailored to exploit the unique properties of this platform. In this article, we explore a number of these software packages and demonstrate how to perform a complete analysis of BeadArray data in various formats. The key steps of importing data, performing quality assessments, preprocessing, and annotation in the common setting of assessing differential expression in designed experiments will be covered. PMID:22144879

Realization of 10 GHz minus 30dB on-chip micro-optical links with Si-Ge RF bi-polar technology

NASA Astrophysics Data System (ADS)

Ogudo, Kingsley A.; Snyman, Lukas W.; Polleux, Jean-Luc; Viana, Carlos; Tegegne, Zerihun

2014-06-01

Si Avalanche based LEDs technology has been developed in the 650 -850nm wavelength regime [1, 2]. Correspondingly, small micro-dimensioned detectors with pW/μm2 sensitivity have been developed for the same wavelength range utilizing Si-Ge detector technology with detection efficiencies of up to 0.85, and with a transition frequencies of up to 80 GHz [3] A series of on-chip optical links of 50 micron length, utilizing 650 - 850 nm propagation wavelength have been designed and realized, utilizing a Si Ge radio frequency bipolar process. Micron dimensioned optical sources, waveguides and detectors were all integrated on the same chip to form a complete optical link on-chip. Avalanche based Si LEDs (Si Av LEDs), Schottky contacting, TEOS densification strategies, silicon nitride based waveguides, and state of the art Si-Ge bipolar detector technologies were used as key design strategies. Best performances show optical coupling from source to detector of up to 10GHz and - 40dBm total optical link budget loss with a potential transition frequency coupling of up to 40GHz utilizing Si Ge based LEDs. The technology is particularly suitable for application as on-chip optical links, optical MEMS and MOEMS, as well as for optical interconnects utilizing low loss, side surface, waveguide- to-optical fiber coupling. Most particularly is one of our designed waveguide which have a good core axis alignment with the optical source and yield 10GHz -30dB on-chip micro-optical links as shown in Fig 9 (c). The technology as developed has been appropriately IP protected.

Experimental study on discretely modulated continuous-variable quantum key distribution

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shen Yong; Zou Hongxin; Chen Pingxing

2010-08-15

We present a discretely modulated continuous-variable quantum key distribution system in free space by using strong coherent states. The amplitude noise in the laser source is suppressed to the shot-noise limit by using a mode cleaner combined with a frequency shift technique. Also, it is proven that the phase noise in the source has no impact on the final secret key rate. In order to increase the encoding rate, we use broadband homodyne detectors and the no-switching protocol. In a realistic model, we establish a secret key rate of 46.8 kbits/s against collective attacks at an encoding rate of 10more » MHz for a 90% channel loss when the modulation variance is optimal.« less

Molecular Characterization of the 2016 New World Screwworm (Diptera: Calliphoridae) Outbreak in the Florida Keys.

PubMed

Dupuis, Julian R; Guerrero, Felix D; Skoda, Steven R; Phillips, Pamela L; Welch, John B; Schlater, Jack L; Azeredo-Espin, Ana Maria L; Pérez de León, Adalberto A; Geib, Scott M

2018-05-19

New World screwworm (NWS), Cochliomyia hominivorax (Coquerel 1858) (Diptera: Calliphoridae), is a myiasis-causing fly that can be a serious threat to the health of livestock, wildlife, and humans. Its progressive eradication from the southern United States, Mexico, and Central America from the 1950s to 2000s is an excellent example of successful pest management using sterile insect technique (SIT). In late 2016, autochthonous NWS were detected in the Florida Keys, representing this species' first invasion in the United States in >30 yr. Rapid use of quarantine and SIT was successful in eliminating the infestation by early 2017; however, the geographic source of this infestation remains unknown. Here, we use amplicon sequencing to generate mitochondrial and nuclear sequence data representing all confirmed cases of NWS from this infestation, and compare these sequences to preexisting data sets sampling the native distribution of NWS. We ask two questions regarding the FL Keys outbreak. First, is this infestation the result of a single invasion from one source, or multiple invasions from different sources? And second, what is the geographic origin of this invasion? We found virtually no sequence variation between specimens collected from the FL Keys outbreak, which is consistent with a single source of introduction. However, we also found very little geographic resolution in any of the data sets, which precludes identification of the source of this outbreak. Our lack of success in answering our second question speaks to the need for finer-scale genetic or genomic assessments of NWS population structure, which would facilitate source determination of potential future outbreaks.

Advanced piloted aircraft flight control system design methodology. Volume 2: The FCX flight control design expert system

NASA Technical Reports Server (NTRS)

Myers, Thomas T.; Mcruer, Duane T.

1988-01-01

The development of a comprehensive and electric methodology for conceptual and preliminary design of flight control systems is presented and illustrated. The methodology is focused on the design states starting with the layout of system requirements and ending when some viable competing system architectures (feedback control structures) are defined. The approach is centered on the human pilot and the aircraft as both the sources of, and the keys to the solution of, many flight control problems. The methodology relies heavily on computational procedures which are highly interactive with the design engineer. To maximize effectiveness, these techniques, as selected and modified to be used together in the methodology, form a cadre of computational tools specifically tailored for integrated flight control system preliminary design purposes. The FCX expert system as presently developed is only a limited prototype capable of supporting basic lateral-directional FCS design activities related to the design example used. FCX presently supports design of only one FCS architecture (yaw damper plus roll damper) and the rules are largely focused on Class IV (highly maneuverable) aircraft. Despite this limited scope, the major elements which appear necessary for application of knowledge-based software concepts to flight control design were assembled and thus FCX represents a prototype which can be tested, critiqued and evolved in an ongoing process of development.

Information Theoretic Secret Key Generation: Structured Codes and Tree Packing

ERIC Educational Resources Information Center

Nitinawarat, Sirin

2010-01-01

This dissertation deals with a multiterminal source model for secret key generation by multiple network terminals with prior and privileged access to a set of correlated signals complemented by public discussion among themselves. Emphasis is placed on a characterization of secret key capacity, i.e., the largest rate of an achievable secret key,…

Non-technical skills training to enhance patient safety.

PubMed

Gordon, Morris

2013-06-01

  Patient safety is an increasingly recognised issue in health care. Systems-based and organisational methods of quality improvement, as well as education focusing on key clinical areas, are common, but there are few reports of educational interventions that focus on non-technical skills to address human factor sources of error. A flexible model for non-technical skills training for health care professionals has been designed based on the best available evidence, and with sound theoretical foundations.   Educational sessions to improve non-technical skills in health care have been described before. The descriptions lack the details to allow educators to replicate and innovate further.   A non-technical skills training course that can be delivered as either a half- or full-day intervention has been designed and delivered to a number of mixed groups of undergraduate medical students and doctors in postgraduate training. Participant satisfaction has been high and patient safety attitudes have improved post-intervention.   This non-technical skills educational intervention has been built on a sound evidence base, and is described so as to facilitate replication and dissemination. With the key themes laid out, clinical educators will be able to build interventions focused on numerous clinical issues that pay attention to human factor contributors to safety. © 2013 John Wiley & Sons Ltd.

Understanding small business engagement in workplace violence prevention programs.

PubMed

Bruening, Rebecca A; Strazza, Karen; Nocera, Maryalice; Peek-Asa, Corinne; Casteel, Carri

2015-01-01

Worksite wellness, safety, and violence prevention programs have low penetration among small, independent businesses. This study examined barriers and strategies influencing small business participation in workplace violence prevention programs (WVPPs). A semistructured interview guide was used in 32 telephone interviews. The study took place at the University of North Carolina Injury Prevention Research Center. Participating were a purposive sample of 32 representatives of small business-serving organizations (e.g., business membership organizations, regulatory agencies, and economic development organizations) selected for their experience with small businesses. This study was designed to inform improved dissemination of Crime Free Business (CFB), a WVPP for small, independent retail businesses. Thematic qualitative data analysis was used to identify key barriers and strategies for promoting programs and services to small businesses. Three key factors that influence small business engagement emerged from the analysis: (1) small businesses' limited time and resources, (2) low salience of workplace violence, (3) influence of informal networks and source credibility. Identified strategies include designing low-cost and convenient programs, crafting effective messages, partnering with influential organizations and individuals, and conducting outreach through informal networks. Workplace violence prevention and public health practitioners may increase small business participation in programs by reducing time and resource demands, addressing small business concerns, enlisting support from influential individuals and groups, and emphasizing business benefits of participating in the program.

Design a freeform microlens array module for any arbitrary-shape collimated beam shaping and color mixing

NASA Astrophysics Data System (ADS)

Chen, Enguo; Wu, Rengmao; Guo, Tailiang

2014-06-01

Collimated beam shaping with freeform surface usually employs a predefined mapping to tailor one or multiple freeform surfaces. Limitation on those designs is that the source, the freeform optics and the target are in fixed one-to-one correspondence with each other. To overcome this drawback, this paper presents a kind of freeform microlens array module integrated with an ultra-thin freeform microlens array and a condenser lens to reshape any arbitrary-shape collimated beam into a prescribed uniform rectangular illumination and achieve color mixing. The design theory is explicitly given, and some key issues are addressed. Several different application examples are given, and the target is obtained with high uniformity and energy efficiency. This freeform microlens array module, which shows better flexibility and practicality than the regular designs, can be used not only to reshape any arbitrary-shape collimated beam (or a collimated beam integrated with several sub-collimated beams), but also most importantly to achieve color mixing. With excellent optical performance and ultra-compact volume, this optical module together with the design theory can be further introduced into other applications and will have a huge market potential in the near future.

[Spatial heterogeneity and classified control of agricultural non-point source pollution in Huaihe River Basin].

PubMed

Zhou, Liang; Xu, Jian-Gang; Sun, Dong-Qi; Ni, Tian-Hua

2013-02-01

Agricultural non-point source pollution is of importance in river deterioration. Thus identifying and concentrated controlling the key source-areas are the most effective approaches for non-point source pollution control. This study adopts inventory method to analysis four kinds of pollution sources and their emissions intensity of the chemical oxygen demand (COD), total nitrogen (TN), and total phosphorus (TP) in 173 counties (cities, districts) in Huaihe River Basin. The four pollution sources include livestock breeding, rural life, farmland cultivation, aquacultures. The paper mainly addresses identification of non-point polluted sensitivity areas, key pollution sources and its spatial distribution characteristics through cluster, sensitivity evaluation and spatial analysis. A geographic information system (GIS) and SPSS were used to carry out this study. The results show that: the COD, TN and TP emissions of agricultural non-point sources were 206.74 x 10(4) t, 66.49 x 10(4) t, 8.74 x 10(4) t separately in Huaihe River Basin in 2009; the emission intensity were 7.69, 2.47, 0.32 t.hm-2; the proportions of COD, TN, TP emissions were 73%, 24%, 3%. The paper achieves that: the major pollution source of COD, TN and TP was livestock breeding and rural life; the sensitivity areas and priority pollution control areas among the river basin of non-point source pollution are some sub-basins of the upper branches in Huaihe River, such as Shahe River, Yinghe River, Beiru River, Jialu River and Qingyi River; livestock breeding is the key pollution source in the priority pollution control areas. Finally, the paper concludes that pollution type of rural life has the highest pollution contribution rate, while comprehensive pollution is one type which is hard to control.

Scalable Metadata Management for a Large Multi-Source Seismic Data Repository

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gaylord, J. M.; Dodge, D. A.; Magana-Zook, S. A.

In this work, we implemented the key metadata management components of a scalable seismic data ingestion framework to address limitations in our existing system, and to position it for anticipated growth in volume and complexity. We began the effort with an assessment of open source data flow tools from the Hadoop ecosystem. We then began the construction of a layered architecture that is specifically designed to address many of the scalability and data quality issues we experience with our current pipeline. This included implementing basic functionality in each of the layers, such as establishing a data lake, designing a unifiedmore » metadata schema, tracking provenance, and calculating data quality metrics. Our original intent was to test and validate the new ingestion framework with data from a large-scale field deployment in a temporary network. This delivered somewhat unsatisfying results, since the new system immediately identified fatal flaws in the data relatively early in the pipeline. Although this is a correct result it did not allow us to sufficiently exercise the whole framework. We then widened our scope to process all available metadata from over a dozen online seismic data sources to further test the implementation and validate the design. This experiment also uncovered a higher than expected frequency of certain types of metadata issues that challenged us to further tune our data management strategy to handle them. Our result from this project is a greatly improved understanding of real world data issues, a validated design, and prototype implementations of major components of an eventual production framework. This successfully forms the basis of future development for the Geophysical Monitoring Program data pipeline, which is a critical asset supporting multiple programs. It also positions us very well to deliver valuable metadata management expertise to our sponsors, and has already resulted in an NNSA Office of Defense Nuclear Nonproliferation commitment to a multi-year project for follow-on work.« less

Key issues in the design of NO{sub x} emission trading programs to reduce ground-level ozone. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nichols, A.; Harrison, D.

1994-07-01

This report is the first product of a study being conducted by National Economic Research Associates for the Electric Power Research Institute to evaluate various market-based alternatives for managing emissions of nitrogen oxides (NO{sub x}) as part of strategies to achieve the ambient ozone standard. The report focuses on choices in the design of relatively broad, ambitious emission trading programs, rather than on more modest programs designed to generate offsets within a regulatory framework that continues to rely primarily on traditional emission standards and nontransferable permits. After a brief introductory chapter, Chapter 2 reviews both the conceptual underpinnings of emissionmore » trading and prior experience. This review suggests the need for clear initial allocations-generally based on emission caps-to simplify trading while assuring the achievement of emission-reduction goals. Chapter 3 lays out the basic choices required in establishing an emission trading program. For concreteness, the basic design is discussed in terms of trading among utilities and other large stationary sources of NO{sub x}, generally the most promising candidates for trading. Chapter 4 discusses various ways in which a basic trading program could be extended to other source categories and to volatile organic compounds (VOCs), the other major precursor of ozone. Chapter 5 analyzes various ways in which trading programs can be refined to focus control efforts on those times and at those locations where ozone problems are most severe. Although highly refined targeting programs are unlikely to be worth the effort, modest differentials can be implemented by making the number of allowances required for each ton of emissions vary with the time and location of emissions. Chapter 6 reviews various alternatives for making the initial allocation of emission allowances among sources in the trading program, breaking the process into two components, an emission rate and an activity level.« less

Clinical software development for the Web: lessons learned from the BOADICEA project

PubMed Central

2012-01-01

Background In the past 20 years, society has witnessed the following landmark scientific advances: (i) the sequencing of the human genome, (ii) the distribution of software by the open source movement, and (iii) the invention of the World Wide Web. Together, these advances have provided a new impetus for clinical software development: developers now translate the products of human genomic research into clinical software tools; they use open-source programs to build them; and they use the Web to deliver them. Whilst this open-source component-based approach has undoubtedly made clinical software development easier, clinical software projects are still hampered by problems that traditionally accompany the software process. This study describes the development of the BOADICEA Web Application, a computer program used by clinical geneticists to assess risks to patients with a family history of breast and ovarian cancer. The key challenge of the BOADICEA Web Application project was to deliver a program that was safe, secure and easy for healthcare professionals to use. We focus on the software process, problems faced, and lessons learned. Our key objectives are: (i) to highlight key clinical software development issues; (ii) to demonstrate how software engineering tools and techniques can facilitate clinical software development for the benefit of individuals who lack software engineering expertise; and (iii) to provide a clinical software development case report that can be used as a basis for discussion at the start of future projects. Results We developed the BOADICEA Web Application using an evolutionary software process. Our approach to Web implementation was conservative and we used conventional software engineering tools and techniques. The principal software development activities were: requirements, design, implementation, testing, documentation and maintenance. The BOADICEA Web Application has now been widely adopted by clinical geneticists and researchers. BOADICEA Web Application version 1 was released for general use in November 2007. By May 2010, we had > 1200 registered users based in the UK, USA, Canada, South America, Europe, Africa, Middle East, SE Asia, Australia and New Zealand. Conclusions We found that an evolutionary software process was effective when we developed the BOADICEA Web Application. The key clinical software development issues identified during the BOADICEA Web Application project were: software reliability, Web security, clinical data protection and user feedback. PMID:22490389

Clinical software development for the Web: lessons learned from the BOADICEA project.

PubMed

Cunningham, Alex P; Antoniou, Antonis C; Easton, Douglas F

2012-04-10

In the past 20 years, society has witnessed the following landmark scientific advances: (i) the sequencing of the human genome, (ii) the distribution of software by the open source movement, and (iii) the invention of the World Wide Web. Together, these advances have provided a new impetus for clinical software development: developers now translate the products of human genomic research into clinical software tools; they use open-source programs to build them; and they use the Web to deliver them. Whilst this open-source component-based approach has undoubtedly made clinical software development easier, clinical software projects are still hampered by problems that traditionally accompany the software process. This study describes the development of the BOADICEA Web Application, a computer program used by clinical geneticists to assess risks to patients with a family history of breast and ovarian cancer. The key challenge of the BOADICEA Web Application project was to deliver a program that was safe, secure and easy for healthcare professionals to use. We focus on the software process, problems faced, and lessons learned. Our key objectives are: (i) to highlight key clinical software development issues; (ii) to demonstrate how software engineering tools and techniques can facilitate clinical software development for the benefit of individuals who lack software engineering expertise; and (iii) to provide a clinical software development case report that can be used as a basis for discussion at the start of future projects. We developed the BOADICEA Web Application using an evolutionary software process. Our approach to Web implementation was conservative and we used conventional software engineering tools and techniques. The principal software development activities were: requirements, design, implementation, testing, documentation and maintenance. The BOADICEA Web Application has now been widely adopted by clinical geneticists and researchers. BOADICEA Web Application version 1 was released for general use in November 2007. By May 2010, we had > 1200 registered users based in the UK, USA, Canada, South America, Europe, Africa, Middle East, SE Asia, Australia and New Zealand. We found that an evolutionary software process was effective when we developed the BOADICEA Web Application. The key clinical software development issues identified during the BOADICEA Web Application project were: software reliability, Web security, clinical data protection and user feedback.

ChoiceKey: a real-time speech recognition program for psychology experiments with a small response set.

PubMed

Donkin, Christopher; Brown, Scott D; Heathcote, Andrew

2009-02-01

Psychological experiments often collect choice responses using buttonpresses. However, spoken responses are useful in many cases-for example, when working with special clinical populations, or when a paradigm demands vocalization, or when accurate response time measurements are desired. In these cases, spoken responses are typically collected using a voice key, which usually involves manual coding by experimenters in a tedious and error-prone manner. We describe ChoiceKey, an open-source speech recognition package for MATLAB. It can be optimized by training for small response sets and different speakers. We show ChoiceKey to be reliable with minimal training for most participants in experiments with two different responses. Problems presented by individual differences, and occasional atypical responses, are examined, and extensions to larger response sets are explored. The ChoiceKey source files and instructions may be downloaded as supplemental materials for this article from brm.psychonomic-journals.org/content/supplemental.

Parameterizations for ensemble Kalman inversion

NASA Astrophysics Data System (ADS)

Chada, Neil K.; Iglesias, Marco A.; Roininen, Lassi; Stuart, Andrew M.

2018-05-01

The use of ensemble methods to solve inverse problems is attractive because it is a derivative-free methodology which is also well-adapted to parallelization. In its basic iterative form the method produces an ensemble of solutions which lie in the linear span of the initial ensemble. Choice of the parameterization of the unknown field is thus a key component of the success of the method. We demonstrate how both geometric ideas and hierarchical ideas can be used to design effective parameterizations for a number of applied inverse problems arising in electrical impedance tomography, groundwater flow and source inversion. In particular we show how geometric ideas, including the level set method, can be used to reconstruct piecewise continuous fields, and we show how hierarchical methods can be used to learn key parameters in continuous fields, such as length-scales, resulting in improved reconstructions. Geometric and hierarchical ideas are combined in the level set method to find piecewise constant reconstructions with interfaces of unknown topology.

Renewable Energy Development in Indian Country: A Handbook for Tribes

DOE Office of Scientific and Technical Information (OSTI.GOV)

MacCourt, D. C.

2010-06-01

This handbook is designed to be an accessible reference for those who are new to tribal energy project development or seek a refresher on key development issues as they navigate the project development process. It builds upon the wealth of feedback and experiences shared by tribal and other participants in the National Renewable Energy Laboratory's tribal energy training sessions to provide tribal leaders, tribal economic and energy enterprises, and those supporting them with a general overview of the renewable energy project development process as well as detailed guidance on the following: how to structure a renewable energy project transaction tomore » protect tribal interests, with an emphasis on joint project development efforts undertaken with nontribal parties; key energy development agreements, including power sale agreements, transmission and interconnection agreements, and land leases; and ways tribes can finance renewable energy projects, including the sources of funding or financing that may be available, the types of investors that may be available, and federal tax incentives for renewable energy projects.« less

Graphene-based chemiluminescence resonance energy transfer for homogeneous immunoassay.

PubMed

Lee, Joon Seok; Joung, Hyou-Arm; Kim, Min-Gon; Park, Chan Beum

2012-04-24

We report on chemiluminescence resonance energy transfer (CRET) between graphene nanosheets and chemiluminescent donors. In contrast to fluorescence resonance energy transfer, CRET occurs via nonradiative dipole-dipole transfer of energy from a chemiluminescent donor to a suitable acceptor molecule without an external excitation source. We designed a graphene-based CRET platform for homogeneous immunoassay of C-reactive protein (CRP), a key marker for human inflammation and cardiovascular diseases, using a luminol/hydrogen peroxide chemiluminescence (CL) reaction catalyzed by horseradish peroxidase. According to our results, anti-CRP antibody conjugated to graphene nanosheets enabled the capture of CRP at the concentration above 1.6 ng mL(-1). In the CRET platform, graphene played a key role as an energy acceptor, which was more efficient than graphene oxide, while luminol served as a donor to graphene, triggering the CRET phenomenon between luminol and graphene. The graphene-based CRET platform was successfully applied to the detection of CRP in human serum samples in the range observed during acute inflammatory stress.

A Miniaturized On-Chip Colorimeter for Detecting NPK Elements.

PubMed

Liu, Rui-Tao; Tao, Lu-Qi; Liu, Bo; Tian, Xiang-Guang; Mohammad, Mohammad Ali; Yang, Yi; Ren, Tian-Ling

2016-08-04

Recently, precision agriculture has become a globally attractive topic. As one of the most important factors, the soil nutrients play an important role in estimating the development of precision agriculture. Detecting the content of nitrogen, phosphorus and potassium (NPK) elements more efficiently is one of the key issues. In this paper, a novel chip-level colorimeter was fabricated to detect the NPK elements for the first time. A light source-microchannel photodetector in a sandwich structure was designed to realize on-chip detection. Compared with a commercial colorimeter, all key parts are based on MEMS (Micro-Electro-Mechanical System) technology so that the volume of this on-chip colorimeter can be minimized. Besides, less error and high precision are achieved. The cost of this colorimeter is two orders of magnitude less than that of a commercial one. All these advantages enable a low-cost and high-precision sensing operation in a monitoring network. The colorimeter developed herein has bright prospects for environmental and biological applications.

Experimental multiplexing of quantum key distribution with classical optical communication

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Liu-Jun; Chen, Luo-Kan; Ju, Lei

2015-02-23

We demonstrate the realization of quantum key distribution (QKD) when combined with classical optical communication, and synchronous signals within a single optical fiber. In the experiment, the classical communication sources use Fabry-Pérot (FP) lasers, which are implemented extensively in optical access networks. To perform QKD, multistage band-stop filtering techniques are developed, and a wavelength-division multiplexing scheme is designed for the multi-longitudinal-mode FP lasers. We have managed to maintain sufficient isolation among the quantum channel, the synchronous channel and the classical channels to guarantee good QKD performance. Finally, the quantum bit error rate remains below a level of 2% across themore » entire practical application range. The proposed multiplexing scheme can ensure low classical light loss, and enables QKD over fiber lengths of up to 45 km simultaneously when the fibers are populated with bidirectional FP laser communications. Our demonstration paves the way for application of QKD to current optical access networks, where FP lasers are widely used by the end users.« less

Exposure Knowledge and Perception of Wireless Communication Technologies.

PubMed

Freudenstein, Frederik; Correia, Luis M; Oliveira, Carla; Sebastião, Daniel; Wiedemann, Peter M

2015-11-06

The presented survey investigates risk and exposure perceptions of radio frequency electromagnetic fields (RF EMF) associated with base stations, mobile phones and other sources, the key issue being the interaction between both sets of perceptions. The study is based on a cross-sectional design, and conducted with an online sample of 838 citizens from Portugal. The results indicate that respondents' intuitive exposure perception differs from the actual exposure levels. Furthermore, exposure and risk perceptions are found to be highly correlated. Respondents' beliefs about exposure factors, which might influence possible health risks, is appropriate. A regression analysis between exposure characteristics, as predictor variables, and RF EMF risk perception, as the response variable, indicates that people seem to use simple heuristics to form their perceptions. What is bigger, more frequent and longer lasting is seen as riskier. Moreover, the quality of exposure knowledge is not an indicator for amplified EMF risk perception. These findings show that exposure perception is key to future risk communication.

Exposure Knowledge and Perception of Wireless Communication Technologies

PubMed Central

Freudenstein, Frederik; Correia, Luis M.; Oliveira, Carla; Sebastião, Daniel; Wiedemann, Peter M.

2015-01-01

The presented survey investigates risk and exposure perceptions of radio frequency electromagnetic fields (RF EMF) associated with base stations, mobile phones and other sources, the key issue being the interaction between both sets of perceptions. The study is based on a cross-sectional design, and conducted with an online sample of 838 citizens from Portugal. The results indicate that respondents’ intuitive exposure perception differs from the actual exposure levels. Furthermore, exposure and risk perceptions are found to be highly correlated. Respondents’ beliefs  about exposure factors, which might influence possible health risks, is appropriate. A regression analysis between exposure characteristics, as predictor variables, and RF EMF risk perception, as the response variable, indicates that people seem to use simple heuristics to form their perceptions. What is bigger, more frequent and longer lasting is seen as riskier. Moreover, the quality of exposure knowledge is not an indicator for amplified EMF risk perception. These findings show that exposure perception is key to future risk communication. PMID:26561826

Designing and Evaluating an Online Role Play in Conflict Management

ERIC Educational Resources Information Center

Hrastinski, Stefan; Watson, Jason

2009-01-01

Purpose: This paper aims to identify, through a literature review, key issues regarding how online role plays can be designed and to apply them when designing a role play on conflict management. Design/methodology/approach: By drawing on the key issues identified in the literature review, a role play on conflict management was designed and…

Low Wind Speed Turbine Project Phase II: The Application of Medium-Voltage Electrical Apparatus to the Class of Variable Speed Multi-Megawatt Low Wind Speed Turbines; 15 June 2004--30 April 2005

DOE Office of Scientific and Technical Information (OSTI.GOV)

Erdman, W.; Behnke, M.

2005-11-01

Kilowatt ratings of modern wind turbines have progressed rapidly from 50 kW to 1,800 kW over the past 25 years, with 3.0- to 7.5-MW turbines expected in the next 5 years. The premise of this study is simple: The rapid growth of wind turbine power ratings and the corresponding growth in turbine electrical generation systems and associated controls are quickly making low-voltage (LV) electrical design approaches cost-ineffective. This report provides design detail and compares the cost of energy (COE) between commercial LV-class wind power machines and emerging medium-voltage (MV)-class multi-megawatt wind technology. The key finding is that a 2.5% reductionmore » in the COE can be achieved by moving from LV to MV systems. This is a conservative estimate, with a 3% to 3.5% reduction believed to be attainable once purchase orders to support a 250-turbine/year production level are placed. This evaluation considers capital costs as well as installation, maintenance, and training requirements for wind turbine maintenance personnel. Subsystems investigated include the generator, pendant cables, variable-speed converter, and padmount transformer with switchgear. Both current-source and voltage-source converter/inverter MV topologies are compared against their low-voltage, voltage-source counterparts at the 3.0-, 5.0-, and 7.5-MW levels.« less

A compact self-flowing lithium system for use in an industrial neutron source

NASA Astrophysics Data System (ADS)

Kalathiparambil, Kishor Kumar; Szott, Matthew; Jurczyk, Brian; Ahn, Chisung; Ruzic, David

2016-10-01

A compact trench module to flow liquid lithium in closed loops for handling high heat and particle flux have been fabricated and tested at UIUC. The module was designed to demonstrate the proof of concept in utilizing liquid metals for two principal objectives: i) as self-healing low Z plasma facing components, which is expected to solve the issues facing the current high Z components and ii) using flowing lithium as an MeV-level neutron source. A continuously flowing lithium loop ensures a fresh lithium interface and also accommodate a higher concentration of D, enabling advanced D-Li reactions without using any radioactive tritium. Such a system is expected to have a base yield of 10e7 n/s. For both the applications, the key success factor of the module is attaining the necessary high flow velocity of the lithium especially over the impact area, which will be the disruptive plasma events in fusion reactors and the incident ion beam for the neutron beam source. This was achieved by the efficient shaping of the trenches to exploit the nozzle effect in liquid flow. The compactness of the module, which can also be scaled as desired, was fulfilled by the use of high Tc permanent magnets and air cooled channels attained the necessary temperature gradient for driving the lithium. The design considerations and parameters, experimental arrangements involving lithium filling and attaining flow, data and results obtained will be elaborated. DOE SBIR project DE-SC0013861.

Shielding and activation calculations around the reactor core for the MYRRHA ADS design

NASA Astrophysics Data System (ADS)

Ferrari, Anna; Mueller, Stefan; Konheiser, J.; Castelliti, D.; Sarotto, M.; Stankovskiy, A.

2017-09-01

In the frame of the FP7 European project MAXSIMA, an extensive simulation study has been done to assess the main shielding problems in view of the construction of the MYRRHA accelerator-driven system at SCK·CEN in Mol (Belgium). An innovative method based on the combined use of the two state-of-the-art Monte Carlo codes MCNPX and FLUKA has been used, with the goal to characterize complex, realistic neutron fields around the core barrel, to be used as source terms in detailed analyses of the radiation fields due to the system in operation, and of the coupled residual radiation. The main results of the shielding analysis are presented, as well as the construction of an activation database of all the key structural materials. The results evidenced a powerful way to analyse the shielding and activation problems, with direct and clear implications on the design solutions.

A Suggested Model for Building Robust Biomedical Implants Registries.

PubMed

Aloufi, Bader; Alshagathrah, Fahad; Househ, Mowafa

2017-01-01

Registries are an essential source of information for clinical and non-clinical decision-makers; because they provide evidence for post-market clinical follow-up and early detection of safety signals for biomedical implants. Yet, many of todays biomedical implants registries are facing a variety of challenges relating to a poorly designed dataset, the reliability of inputted data and low clinician and patient participation. The purpose of this paper is to present a best practice model for the implementation and use of biomedical implants registries to monitor the safety and effectiveness of implantable medical devices. Based on a literature review and an analysis of multiple national relevant registries, we identified six factors that address contemporary challenges and are believed to be the keys for building a successful biomedical implants registry, which include: sustainable development, international comparability, data reliability, purposeful design, ease of patient participation, and collaborative development at the national level.

Transverse diode-pumped neodymium-doped yttrium vanadate laser of simple design

NASA Astrophysics Data System (ADS)

Agüero, Mónica B.; Hnilo, Alejandro A.; Kovalsky, Marcelo G.

2010-03-01

The design and performance of an all-solid-state Nd:YVO4 laser, transversely pumped by a single 20-W (at 808 nm) diode with no coupling optics, are presented. The prototype, which is devised to be the source of a micro-LIDAR station, is very simple, easy to align, compact, and stable. The key element is a roof prism as the end mirror of the laser cavity, which is used to symmetrize the effects of the thermal distortion and the inhomogeneity of the population inversion distribution. Typical numbers are 4.2-W cw with a slightly astigmatic (3:2) homogeneous spot and a divergence of 0.5 mrad. The protoype is also tested in the active Q-switching mode, providing pulses 50-ns full width at half maximum (FWHM) at 14 KHz, 3.5 W average. Frequency doubling external to the cavity in a nonoptimized configuration provides 700 mW at 532 nm.

pyQms enables universal and accurate quantification of mass spectrometry data.

PubMed

Leufken, Johannes; Niehues, Anna; Sarin, L Peter; Wessel, Florian; Hippler, Michael; Leidel, Sebastian A; Fufezan, Christian

2017-10-01

Quantitative mass spectrometry (MS) is a key technique in many research areas (1), including proteomics, metabolomics, glycomics, and lipidomics. Because all of the corresponding molecules can be described by chemical formulas, universal quantification tools are highly desirable. Here, we present pyQms, an open-source software for accurate quantification of all types of molecules measurable by MS. pyQms uses isotope pattern matching that offers an accurate quality assessment of all quantifications and the ability to directly incorporate mass spectrometer accuracy. pyQms is, due to its universal design, applicable to every research field, labeling strategy, and acquisition technique. This opens ultimate flexibility for researchers to design experiments employing innovative and hitherto unexplored labeling strategies. Importantly, pyQms performs very well to accurately quantify partially labeled proteomes in large scale and high throughput, the most challenging task for a quantification algorithm. © 2017 by The American Society for Biochemistry and Molecular Biology, Inc.

Management of data from clinical trials using the ArchiMed system.

PubMed

Duftschmid, Georg; Gall, Walter; Eigenbauer, Ernst; Dorda, Wolfgang

2002-06-01

Clinical trials constitute a key source of medical research and are therefore conducted on a regular basis at university hospitals. The professional execution of trials requires, among other things, a repertoire of tools that support efficient data management. Tasks that are essential for efficient data management in clinical trials include the following: the design of the trial database, the design of electronic case report forms, recruiting patients, collection of data, and statistical analysis. The present article reports the manner in which these tasks are supported by the ArchiMed system at the University of Vienna and Graz Medical Schools. ArchiMed is customized for clinical end users, allowing them to autonomously manage their clinical trials without having to consult computer experts. An evaluation of the ArchiMed system in 12 trials recently conducted at the University of Vienna Medical School shows that the individual system functions can be usefully applied for data management in clinical trials.

Advancing Technology for Starlight Suppression via an External Occulter

NASA Technical Reports Server (NTRS)

Kasdin, N. J.; Spergel, D. N.; Vanderbei, R. J.; Lisman, D.; Shaklan, S.; Thomson, M.; Walkemeyer, P.; Bach, V.; Oakes, E.; Cady, E.;

Human Mars Surface Mission Nuclear Power Considerations

NASA Technical Reports Server (NTRS)

Rucker, Michelle A.

2018-01-01

A key decision facing Mars mission designers is how to power a crewed surface field station. Unlike the solar-powered Mars Exploration Rovers (MER) that could retreat to a very low power state during a Martian dust storm, human Mars surface missions are estimated to need at least 15 kilowatts of electrical (kWe) power simply to maintain critical life support and spacecraft functions. 'Hotel' loads alone for a pressurized crew rover approach two kWe; driving requires another five kWe-well beyond what the Curiosity rover’s Radioisotope Power System (RPS) was designed to deliver. Full operation of a four-crew Mars field station is estimated at about 40 kWe. Clearly, a crewed Mars field station will require a substantial and reliable power source, beyond the scale of robotic mission experience. This paper explores the applications for both fission and RPS nuclear options for Mars.

Thermal analysis of a conceptual design for a 250 We GPHS/FPSE space power system

NASA Technical Reports Server (NTRS)

Mccomas, Thomas J.; Dugan, Edward T.

1991-01-01

A thermal analysis has been performed for a 250-We space nuclear power system which combines the US Department of Energy's general purpose heat source (GPHS) modules with a state-of-the-art free-piston Stirling engine (FPSE). The focus of the analysis is on the temperature of the indium fuel clad within the GPHS modules. The thermal analysis results indicate fuel clad temperatures slightly higher than the design goal temperature of 1573 K. The results are considered favorable due to numerous conservative assumptions used. To demonstrate the effects of the conservatism, a brief sensitivity analysis is performed in which a few of the key system parameters are varied to determine their effect on the fuel clad temperatures. It is shown that thermal analysis of a more detailed thermal mode should yield fuel clad temperatures below 1573 K.

Relating design and environmental variables to reliability

NASA Astrophysics Data System (ADS)

Kolarik, William J.; Landers, Thomas L.

The combination of space application and nuclear power source demands high reliability hardware. The possibilities of failure, either an inability to provide power or a catastrophic accident, must be minimized. Nuclear power experiences on the ground have led to highly sophisticated probabilistic risk assessment procedures, most of which require quantitative information to adequately assess such risks. In the area of hardware risk analysis, reliability information plays a key role. One of the lessons learned from the Three Mile Island experience is that thorough analyses of critical components are essential. Nuclear grade equipment shows some reliability advantages over commercial. However, no statistically significant difference has been found. A recent study pertaining to spacecraft electronics reliability, examined some 2500 malfunctions on more than 300 aircraft. The study classified the equipment failures into seven general categories. Design deficiencies and lack of environmental protection accounted for about half of all failures. Within each class, limited reliability modeling was performed using a Weibull failure model.

Lessons learned from national food fortification projects: experiences from Morocco, Uzbekistan, and Vietnam.

PubMed

Wirth, James P; Laillou, Arnaud; Rohner, Fabian; Northrop-Clewes, Christine A; Macdonald, Barbara; Moench-Pfanner, Regina

2012-12-01

Fortification of staple foods has been repeatedly recommended as an effective approach to reduce micronutrient deficiencies. With the increased number of fortification projects globally, there is a need to share practical lessons learned relating to their implementation and responses to project-related and external challenges. To document the achievements, challenges, lessons learned, and management responses associated with national fortification projects in Morocco, Uzbekistan, and Vietnam. Independent end-of-project evaluations conducted for each project served as the primary data source and contain the history of and project activities undertaken for, each fortification project. Other sources, including national policy documents, project reports from the Global Alliance for Improved Nutrition (GAIN) and other stakeholders, industry assessments, and peer-reviewed articles, were used to document the current responses to challenges and future project plans. All projects had key achievements related to the development of fortification standards and the procurement of equipment for participating industry partners. Mandatory fortification of wheat flour was a key success in Morocco and Uzbekistan. Ensuring the quality of fortified foods was a common challenge experienced across the projects, as were shifts in consumption patterns and market structures. Adjustments were made to the projects' design to address the challenges faced. National fortification projects are dynamic and must be continually modified in response to specific performance issues and broader shifts in market structure and consumption patterns.

Magnetic field design for a Penning ion source for a 200 keV electrostatic accelerator

NASA Astrophysics Data System (ADS)

Fathi, A.; Feghhi, S. A. H.; Sadati, S. M.; Ebrahimibasabi, E.

2017-04-01

In this study, the structure of magnetic field for a Penning ion source has been designed and constructed with the use of permanent magnets. The ion source has been designed and constructed for a 200 keV electrostatic accelerator. With using CST Studio Suite, the magnetic field profile inside the ion source was simulated and an appropriate magnetic system was designed to improve particle confinement. Designed system consists of two ring magnets with 9 mm distance from each other around the anode. The ion source was constructed and the cylindrical magnet and designed magnetic system were tested on the ion source. The results showed that the ignition voltage for ion source with the designed magnetic system is almost 300 V lower than the ion source with the cylindrical magnet. Better particle confinement causes lower voltage discharge to occur.

Relativistic quantum cryptography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Molotkov, S. N., E-mail: molotkov@issp.ac.ru

2011-03-15

A new protocol of quantum key distribution is proposed to transmit keys through free space. Along with quantum-mechanical restrictions on the discernibility of nonorthogonal quantum states, the protocol uses additional restrictions imposed by special relativity theory. Unlike all existing quantum key distribution protocols, this protocol ensures key secrecy for a not strictly one-photon source of quantum states and an arbitrary length of a quantum communication channel.

SOFIA: a flexible source finder for 3D spectral line data

NASA Astrophysics Data System (ADS)

Serra, Paolo; Westmeier, Tobias; Giese, Nadine; Jurek, Russell; Flöer, Lars; Popping, Attila; Winkel, Benjamin; van der Hulst, Thijs; Meyer, Martin; Koribalski, Bärbel S.; Staveley-Smith, Lister; Courtois, Hélène

2015-04-01

We introduce SOFIA, a flexible software application for the detection and parametrization of sources in 3D spectral line data sets. SOFIA combines for the first time in a single piece of software a set of new source-finding and parametrization algorithms developed on the way to future H I surveys with ASKAP (WALLABY, DINGO) and APERTIF. It is designed to enable the general use of these new algorithms by the community on a broad range of data sets. The key advantages of SOFIA are the ability to: search for line emission on multiple scales to detect 3D sources in a complete and reliable way, taking into account noise level variations and the presence of artefacts in a data cube; estimate the reliability of individual detections; look for signal in arbitrarily large data cubes using a catalogue of 3D coordinates as a prior; provide a wide range of source parameters and output products which facilitate further analysis by the user. We highlight the modularity of SOFIA, which makes it a flexible package allowing users to select and apply only the algorithms useful for their data and science questions. This modularity makes it also possible to easily expand SOFIA in order to include additional methods as they become available. The full SOFIA distribution, including a dedicated graphical user interface, is publicly available for download.

Progress towards practical device-independent quantum key distribution with spontaneous parametric down-conversion sources, on-off photodetectors, and entanglement swapping

NASA Astrophysics Data System (ADS)

Seshadreesan, Kaushik P.; Takeoka, Masahiro; Sasaki, Masahide

2016-04-01

Device-independent quantum key distribution (DIQKD) guarantees unconditional security of a secret key without making assumptions about the internal workings of the devices used for distribution. It does so using the loophole-free violation of a Bell's inequality. The primary challenge in realizing DIQKD in practice is the detection loophole problem that is inherent to photonic tests of Bell' s inequalities over lossy channels. We revisit the proposal of Curty and Moroder [Phys. Rev. A 84, 010304(R) (2011), 10.1103/PhysRevA.84.010304] to use a linear optics-based entanglement-swapping relay (ESR) to counter this problem. We consider realistic models for the entanglement sources and photodetectors: more precisely, (a) polarization-entangled states based on pulsed spontaneous parametric down-conversion sources with infinitely higher-order multiphoton components and multimode spectral structure, and (b) on-off photodetectors with nonunit efficiencies and nonzero dark-count probabilities. We show that the ESR-based scheme is robust against the above imperfections and enables positive key rates at distances much larger than what is possible otherwise.

What are single photons good for?

NASA Astrophysics Data System (ADS)

Sangouard, Nicolas; Zbinden, Hugo

2012-10-01

In a long-held preconception, photons play a central role in present-day quantum technologies. But what are sources producing photons one by one good for precisely? Well, in opposition to what many suggest, we show that single-photon sources are not helpful for point to point quantum key distribution because faint laser pulses do the job comfortably. However, there is no doubt about the usefulness of sources producing single photons for future quantum technologies. In particular, we show how single-photon sources could become the seed of a revolution in the framework of quantum communication, making the security of quantum key distribution device-independent or extending quantum communication over many hundreds of kilometers. Hopefully, these promising applications will provide a guideline for researchers to develop more and more efficient sources, producing narrowband, pure and indistinguishable photons at appropriate wavelengths.

Building Energy Management Open Source Software

DOE Office of Scientific and Technical Information (OSTI.GOV)

This is the repository for Building Energy Management Open Source Software (BEMOSS), which is an open source operating system that is engineered to improve sensing and control of equipment in small- and medium-sized commercial buildings. BEMOSS offers the following key features: (1) Open source, open architecture – BEMOSS is an open source operating system that is built upon VOLTTRON – a distributed agent platform developed by Pacific Northwest National Laboratory (PNNL). BEMOSS was designed to make it easy for hardware manufacturers to seamlessly interface their devices with BEMOSS. Software developers can also contribute to adding additional BEMOSS functionalities and applications.more » (2) Plug & play – BEMOSS was designed to automatically discover supported load controllers (including smart thermostats, VAV/RTUs, lighting load controllers and plug load controllers) in commercial buildings. (3) Interoperability – BEMOSS was designed to work with load control devices form different manufacturers that operate on different communication technologies and data exchange protocols. (4) Cost effectiveness – Implementation of BEMOSS deemed to be cost-effective as it was built upon a robust open source platform that can operate on a low-cost single-board computer, such as Odroid. This feature could contribute to its rapid deployment in small- or medium-sized commercial buildings. (5) Scalability and ease of deployment – With its multi-node architecture, BEMOSS provides a distributed architecture where load controllers in a multi-floor and high occupancy building could be monitored and controlled by multiple single-board computers hosting BEMOSS. This makes it possible for a building engineer to deploy BEMOSS in one zone of a building, be comfortable with its operation, and later on expand the deployment to the entire building to make it more energy efficient. (6) Ability to provide local and remote monitoring – BEMOSS provides both local and remote monitoring ability with role-based access control. (7) Security – In addition to built-in security features provided by VOLTTRON, BEMOSS provides enhanced security features, including BEMOSS discovery approval process, encrypted core-to-node communication, thermostat anti-tampering feature and many more. (8) Support from the Advisory Committee – BEMOSS was developed in consultation with an advisory committee from the beginning of the project. BEMOSS advisory committee comprises representatives from 22 organizations from government and industry.« less

Quantum-key-distribution protocol with pseudorandom bases

NASA Astrophysics Data System (ADS)

Trushechkin, A. S.; Tregubov, P. A.; Kiktenko, E. O.; Kurochkin, Y. V.; Fedorov, A. K.

2018-01-01

Quantum key distribution (QKD) offers a way for establishing information-theoretical secure communications. An important part of QKD technology is a high-quality random number generator for the quantum-state preparation and for post-processing procedures. In this work, we consider a class of prepare-and-measure QKD protocols, utilizing additional pseudorandomness in the preparation of quantum states. We study one of such protocols and analyze its security against the intercept-resend attack. We demonstrate that, for single-photon sources, the considered protocol gives better secret key rates than the BB84 and the asymmetric BB84 protocols. However, the protocol strongly requires single-photon sources.

Teaching key use to persons with severe disabilities in congregate living settings.

PubMed

Ivancic, M T; Schepis, M M

1995-01-01

Key use remains overlooked for increasing independent material use by persons with severe mental retardation. In Experiment 1, a procedure to train key locating was evaluated in a multiple-probe withdrawal design across three groups of participants. Most participants located their keys when reinforced for doing so; however, key locating decreased when the reinforcement procedure was withdrawn. In Experiment 2, a multiple probe design across four participant groups was used to evaluate a training procedure to teach key use. Twenty of 25 participants used a key to open and lock their personal lockers as a result of training. However, only 36% of the participants were able to use their keys without prompts from experimenters.

Trauma systems and the costs of trauma care.

PubMed Central

Goldfarb, M G; Bazzoli, G J; Coffey, R M

1996-01-01

OBJECTIVE. This study examines the cost of providing trauma services in trauma centers organized by publicly administered trauma systems, compared to hospitals not part of a formal trauma system. DATA SOURCES AND STUDY SETTING. Secondary administrative discharge abstracts for a national sample of severely injured trauma patients in 44 trauma centers and 60 matched control hospitals for the year 1987 were used. STUDY DESIGN. Retrospective univariate and multivariate analyses were conducted to examine the impact of formal trauma systems and trauma center designation on the costs of treating trauma patients. Key dependent variables included length of stay, charge per day per patient, and charge per hospital stay. Key impact variables were type of trauma system and level of trauma designation. Control variables included patient, hospital, and community characteristics. DATA COLLECTION/EXTRACTION METHODS. Data were selected for hospitals based on (1) a large national hospital discharge database, the Hospital Cost and Utilization Project, 1980-1987 (HCUP-2) and (2) a special survey of trauma systems and trauma designation undertaken by the Hospital Research and Educational Trust of the American Hospital Association. PRINCIPAL FINDINGS. The results show that publicly designated Level I trauma centers, which are the focal point of most trauma systems, have the highest charge per case, the highest average charge per day, and similar or longer average lengths of stay than other hospitals. These findings persist after controlling for patient injury and health status, and for demographic characteristics and hospital and community characteristics. CONCLUSIONS. Prior research shows that severely injured trauma patients have greater chances of survival when treated in specialized trauma centers. However, findings here should be of concern to the many states developing trauma systems since the high costs of Level I centers support limiting the number of centers designated at this level and/or reconsidering the requirements placed on these centers. PMID:8617611

A room for design: Through participatory design young adults with schizophrenia become strong collaborators.

PubMed

Terp, Malene; Laursen, Birgitte Schantz; Jørgensen, Rikke; Mainz, Jan; Bjørnes, Charlotte D

2016-12-01

Smartphone technology is being increasingly viewed as key to engaging young adults with schizophrenia in their own mental health care. In an attempt to use smartphones as an engagement tool, we conducted a participatory design process, where young adults with schizophrenia (n = 4), healthcare providers (n = 7), software designers (n = 3), graphic designer (n = 1), graphic recorder (n = 1), and team leader (n = 1) co-designed a smartphone application for use in early phase schizophrenia care. This paper reports the co-design process. Based on a variety of written data-sources, the paper describes if, and how, participatory design can help construct a physical and relational environment that enables young adults with schizophrenia to become active participants in the design of a more participatory mental health practice. Guided by Etienne Wenger's construct of Community of Practice, three major categories of characteristics and construction of a physical and relational environment supporting and inspiring participation and engagement were identified: (i) a pre-narrative about a community of practice, (ii) the room for design is a community of practice and (iii) the community of practice as a practice of special qualities. It is concluded that participatory design can support and inspire participation and engagement in the development of mental health care with young adults with schizophrenia, given that the environment in which participatory design unfolds is transparent, flexible, secure and informal. © 2016 Australian College of Mental Health Nurses Inc.

Vehicle noise source heights & sub-source spectra

DOT National Transportation Integrated Search

1996-12-01

This report describes a turn-key system that was developed and implemented to collect the vehicle source height database for incorporation into the new Traffic Noise Model (TNM). A total of 2500 individual vehicle pass-bys were measured with this sys...

Quasi-experimental study designs series-paper 10: synthesizing evidence for effects collected from quasi-experimental studies presents surmountable challenges.

PubMed

Becker, Betsy Jane; Aloe, Ariel M; Duvendack, Maren; Stanley, T D; Valentine, Jeffrey C; Fretheim, Atle; Tugwell, Peter

2017-09-01

To outline issues of importance to analytic approaches to the synthesis of quasi-experiments (QEs) and to provide a statistical model for use in analysis. We drew on studies of statistics, epidemiology, and social-science methodology to outline methods for synthesis of QE studies. The design and conduct of QEs, effect sizes from QEs, and moderator variables for the analysis of those effect sizes were discussed. Biases, confounding, design complexities, and comparisons across designs offer serious challenges to syntheses of QEs. Key components of meta-analyses of QEs were identified, including the aspects of QE study design to be coded and analyzed. Of utmost importance are the design and statistical controls implemented in the QEs. Such controls and any potential sources of bias and confounding must be modeled in analyses, along with aspects of the interventions and populations studied. Because of such controls, effect sizes from QEs are more complex than those from randomized experiments. A statistical meta-regression model that incorporates important features of the QEs under review was presented. Meta-analyses of QEs provide particular challenges, but thorough coding of intervention characteristics and study methods, along with careful analysis, should allow for sound inferences. Copyright © 2017 Elsevier Inc. All rights reserved.

Cohort studies in health sciences librarianship.

PubMed

Eldredge, Jonathan

2002-10-01

What are the key characteristics of the cohort study design and its varied applications, and how can this research design be utilized in health sciences librarianship? The health, social, behavioral, biological, library, earth, and management sciences literatures were used as sources. All fields except for health sciences librarianship were scanned topically for either well-known or diverse applications of the cohort design. The health sciences library literature available to the author principally for the years 1990 to 2000, supplemented by papers or posters presented at annual meetings of the Medical Library Association. A narrative review for the health, social, behavioral, biological, earth, and management sciences literatures and a systematic review for health sciences librarianship literature for the years 1990 to 2000, with three exceptions, were conducted. The author conducted principally a manual search of the health sciences librarianship literature for the years 1990 to 2000 as part of this systematic review. The cohort design has been applied to answer a wide array of theoretical or practical research questions in the health, social, behavioral, biological, and management sciences. Health sciences librarianship also offers several major applications of the cohort design. The cohort design has great potential for answering research questions in the field of health sciences librarianship, particularly evidence-based librarianship (EBL), although that potential has not been fully explored.

Advanced piloted aircraft flight control system design methodology. Volume 1: Knowledge base

NASA Technical Reports Server (NTRS)

Mcruer, Duane T.; Myers, Thomas T.

1988-01-01

The development of a comprehensive and electric methodology for conceptual and preliminary design of flight control systems is presented and illustrated. The methodology is focused on the design stages starting with the layout of system requirements and ending when some viable competing system architectures (feedback control structures) are defined. The approach is centered on the human pilot and the aircraft as both the sources of, and the keys to the solution of, many flight control problems. The methodology relies heavily on computational procedures which are highly interactive with the design engineer. To maximize effectiveness, these techniques, as selected and modified to be used together in the methodology, form a cadre of computational tools specifically tailored for integrated flight control system preliminary design purposes. While theory and associated computational means are an important aspect of the design methodology, the lore, knowledge and experience elements, which guide and govern applications are critical features. This material is presented as summary tables, outlines, recipes, empirical data, lists, etc., which encapsulate a great deal of expert knowledge. Much of this is presented in topical knowledge summaries which are attached as Supplements. The composite of the supplements and the main body elements constitutes a first cut at a a Mark 1 Knowledge Base for manned-aircraft flight control.

Practical passive decoy state measurement-device-independent quantum key distribution with unstable sources.

PubMed

Liu, Li; Guo, Fen-Zhuo; Wen, Qiao-Yan

2017-09-12

Measurement-device-independent quantum key distribution (MDI-QKD) with the active decoy state method can remove all detector loopholes, and resist the imperfections of sources. But it may lead to side channel attacks and break the security of QKD system. In this paper, we apply the passive decoy state method to the MDI-QKD based on polarization encoding mode. Not only all attacks on detectors can be removed, but also the side channel attacks on sources can be overcome. We get that the MDI-QKD with our passive decoy state method can have a performance comparable to the protocol with the active decoy state method. To fit for the demand of practical application, we discuss intensity fluctuation in the security analysis of MDI-QKD protocol using passive decoy state method, and derive the key generation rate for our protocol with intensity fluctuation. It shows that intensity fluctuation has an adverse effect on the key generation rate which is non-negligible, especially in the case of small data size of total transmitting signals and long distance transmission. We give specific simulations on the relationship between intensity fluctuation and the key generation rate. Furthermore, the statistical fluctuation due to the finite length of data is also taken into account.

Field Testing GEOICE: A Next-Generation Polar Seismometer

NASA Astrophysics Data System (ADS)

Beaudoin, B. C.; Winberry, J. P.; Huerta, A. D.; Chung, P.; Parker, T.; Anderson, K. R.; Bilek, S. L.; Carpenter, P.

2015-12-01

We report on the development of a new NSF MRI-community supported seismic observatory designed for studies in ice-covered regions - the Geophysical Earth Observatory for Ice Covered Environs (GEOICE). This project is motivated by the need to densify and optimize the collection of high-quality seismic data relevant to key solid Earth and cryosphere science questions. The GEOICE instruments and their power and other ancillary systems are being designed to require minimal installation time and logistical load (i.e., size and weight), while maximizing ease-of-use in the field. The system is capable of advanced data handling and telemetry while being able to withstand conditions associated with icy environments, including cold/wet conditions and high-latitude solar limitations. The instrument capability will include a hybrid seismograph pool of broadband and intermediate elements for observation of both long-period signals (e.g, long-period surface waves and slow sources) and intermediate-to-short-period signals (e.g., teleseismic body waves, local seismicity, and impulsive or extended glaciogenic signals).Key features will include a design that integrates the seismometer and digitizer into a single, environmentally and mechanically robust housing; very low power requirements (~1 watt) for the intermediate-band systems; and advanced power systems that optimize battery capacity and operational limits. The envisioned ~100 element GEOICE instruments will nearly double the current polar inventory of stations and will be maintained and supported at the IRIS PASSCAL Instrument Center to ensure full and flexible peer-reviewed community use. Prototype instruments are currently deployed in Antarctica and Alaska, with a larger Antarctic deployment planned for the 2015-2016 season. The results of these field tests will help to refine instrumentation design and lead to the production of robust and capable next-generation seismic sensors.

Experimental investigation into the fault response of superconducting hybrid electric propulsion electrical power system to a DC rail to rail fault

NASA Astrophysics Data System (ADS)

Nolan, S.; Jones, C. E.; Munro, R.; Norman, P.; Galloway, S.; Venturumilli, S.; Sheng, J.; Yuan, W.

2017-12-01

Hybrid electric propulsion aircraft are proposed to improve overall aircraft efficiency, enabling future rising demands for air travel to be met. The development of appropriate electrical power systems to provide thrust for the aircraft is a significant challenge due to the much higher required power generation capacity levels and complexity of the aero-electrical power systems (AEPS). The efficiency and weight of the AEPS is critical to ensure that the benefits of hybrid propulsion are not mitigated by the electrical power train. Hence it is proposed that for larger aircraft (~200 passengers) superconducting power systems are used to meet target power densities. Central to the design of the hybrid propulsion AEPS is a robust and reliable electrical protection and fault management system. It is known from previous studies that the choice of protection system may have a significant impact on the overall efficiency of the AEPS. Hence an informed design process which considers the key trades between choice of cable and protection requirements is needed. To date the fault response of a voltage source converter interfaced DC link rail to rail fault in a superconducting power system has only been investigated using simulation models validated by theoretical values from the literature. This paper will present the experimentally obtained fault response for a variety of different types of superconducting tape for a rail to rail DC fault. The paper will then use these as a platform to identify key trades between protection requirements and cable design, providing guidelines to enable future informed decisions to optimise hybrid propulsion electrical power system and protection design.

Elisa technology consolidation study overview

NASA Astrophysics Data System (ADS)

Fitzsimons, E. D.; Brandt, N.; Johann, U.; Kemble, S.; Schulte, H.-R.; Weise, D.; Ziegler, T.

2017-11-01

The eLISA (evolved Laser Interferometer Space Antenna) mission is an ESA L3 concept mission intended to detect and characterise gravitational radiation emitted from astrophysical sources [1]. Current designs for eLISA [2] are based on the ESA study conducted in 2011 to reformulate the original ESA/NASA LISA concept [3] into an ESA-only L1 candidate named NGO (New Gravitational Observatory) [4]. During this brief reformulation period, a number of significant changes were made to the baseline LISA design in order to create a more costeffective mission. Some of the key changes implemented during this reformulation were: • A reduction in the inter satellite distance (the arm length) from 5 Gm to 1 Gm. • A reduction in the diameter of the telescope from 40 cm to 20 cm. • A reduction in the required laser power by approximately 40%. • Implementation of only 2 laser arms instead of 3. Many further simplifications were then enabled by these main design changes including the elimination of payload items in the two spacecraft (S/C) with no laser-link between them (the daughter S/C), a reduction in the size and complexity of the optical bench and the elimination of the Point Ahead Angle Mechanism (PAAM), which corrects for variations in the pointing direction to the far S/C caused by orbital dynamics [4] [5]. In the run-up to an L3 mission definition phase later in the decade, it is desirable to review these design choices and analyse the inter-dependencies and scaling between the key mission parameters with the goal of better understanding the parameter space and ensuring that in the final selection of the eLISA mission parameters the optimal balance between cost, complexity and science return can be achieved.

Intelligence by design in an entropic power grid

NASA Astrophysics Data System (ADS)

Negrete-Pincetic, Matias Alejandro

In this work, the term Entropic Grid is coined to describe a power grid with increased levels of uncertainty and dynamics. These new features will require the reconsideration of well-established paradigms in the way of planning and operating the grid and its associated markets. New tools and models able to handle uncertainty and dynamics will form the required scaffolding to properly capture the behavior of the physical system, along with the value of new technologies and policies. The leverage of this knowledge will facilitate the design of new architectures to organize power and energy systems and their associated markets. This work presents several results, tools and models with the goal of contributing to that design objective. A central idea of this thesis is that the definition of products is critical in electricity markets. When markets are constructed with appropriate product definitions in mind, the interference between the physical and the market/financial systems seen in today's markets can be reduced. A key element of evaluating market designs is understanding the impact that salient features of an entropic grid---uncertainty, dynamics, constraints---can have on the electricity markets. Dynamic electricity market models tailored to capture such features are developed in this work. Using a multi-settlement dynamic electricity market, the impact of volatility is investigated. The results show the need to implement policies and technologies able to cope with the volatility of renewable sources. Similarly, using a dynamic electricity market model in which ramping costs are considered, the impacts of those costs on electricity markets are investigated. The key conclusion is that those additional ramping costs, in average terms, are not reflected in electricity prices. These results reveal several difficulties with today's real-time markets. Elements of an alternative architecture to organize these markets are also discussed.

Novel techniques for characterization of hydrocarbon emission sources in the Barnett Shale

NASA Astrophysics Data System (ADS)

Nathan, Brian Joseph

Changes in ambient atmospheric hydrocarbon concentrations can have both short-term and long-term effects on the atmosphere and on human health. Thus, accurate characterization of emissions sources is critically important. The recent boom in shale gas production has led to an increase in hydrocarbon emissions from associated processes, though the exact extent is uncertain. As an original quantification technique, a model airplane equipped with a specially-designed, open-path methane sensor was flown multiple times over a natural gas compressor station in the Barnett Shale in October 2013. A linear optimization was introduced to a standard Gaussian plume model in an effort to determine the most probable emission rate coming from the station. This is shown to be a suitable approach given an ideal source with a single, central plume. Separately, an analysis was performed to characterize the nonmethane hydrocarbons in the Barnett during the same period. Starting with ambient hourly concentration measurements of forty-six hydrocarbon species, Lagrangian air parcel trajectories were implemented in a meteorological model to extend the resolution of these measurements and achieve domain-fillings of the region for the period of interest. A self-organizing map (a type of unsupervised classification) was then utilized to reduce the dimensionality of the total multivariate set of grids into characteristic one-dimensional signatures. By also introducing a self-organizing map classification of the contemporary wind measurements, the spatial hydrocarbon characterizations are analyzed for periods with similar wind conditions. The accuracy of the classification is verified through assessment of observed spatial mixing ratio enhancements of key species, through site-comparisons with a related long-term study, and through a random forest analysis (an ensemble learning method of supervised classification) to determine the most important species for defining key classes. The hydrocarbon classification is shown to have performed very well in identifying expected signatures near and downwind-of oil and gas facilities with active permits, which showcases this method's usefulness for future regional hydrocarbon source-apportionment analyses.

Crouching Tiger, Hidden Trouble: Urban Sources of Aedes albopictus (Diptera: Culicidae) Refractory to Source-Reduction

PubMed Central

Unlu, Isik; Farajollahi, Ary; Strickman, Daniel; Fonseca, Dina M.

2013-01-01

Our ultimate objective is to design cost-effective control strategies for Aedes albopictus, the Asian tiger mosquito, an important urban nuisance and disease vector that expanded worldwide during the last 40 years.  We conducted mosquito larval surveys from May through October 2009 in the City of Trenton, New Jersey, USA, while performing intensive monthly source-reduction campaigns that involved removing, emptying, or treating all accessible containers with larvicides and pupicides. We examined patterns of occurrence of Ae. albopictus and Culex pipiens, another urban mosquito, among different container types by comparing observed and expected number of positive containers of each type. Expected use was based on the relative frequency of each container type in the environment. Aedes albopictus larvae and pupae were found significantly more often than expected in medium volumes of water in buckets and plant saucers but were rarely collected in small volumes of water found in trash items such as discarded cups and cans. They were also absent from large volumes of water such as in abandoned swimming pools and catch basins, although we consistently collected Cx. pipiens from those habitats. The frequency of Ae. albopictus in tires indicated rapid and extensive use of these ubiquitous urban containers. Standard larval-based indices did not correlate with adult catches in BG-Sentinel traps, but when based only on Ae. albopictus key containers (buckets, plant saucers, equipment with pockets of water, and tires) they did. Although we found that only 1.2% of the 20,039 water-holding containers examined contained immature Ae. albopictus (5.3% if only key containers were counted), adult populations were still above nuisance action thresholds six times during the 2009 mosquito season. We conclude that in urban New Jersey, effective source reduction for Ae. albopictus control will require scrupulous and repeated cleaning or treatment of everyday use containers and extensive homeowner collaboration. PMID:24167593

HIV Epidemic Appraisals for Assisting in the Design of Effective Prevention Programmes: Shifting the Paradigm Back to Basics

PubMed Central

Mishra, Sharmistha; Sgaier, Sema K.; Thompson, Laura H.; Moses, Stephen; Ramesh, B. M.; Alary, Michel; Wilson, David; Blanchard, James F.

2012-01-01

Background To design HIV prevention programmes, it is critical to understand the temporal and geographic aspects of the local epidemic and to address the key behaviours that drive HIV transmission. Two methods have been developed to appraise HIV epidemics and guide prevention strategies. The numerical proxy method classifies epidemics based on current HIV prevalence thresholds. The Modes of Transmission (MOT) model estimates the distribution of incidence over one year among risk-groups. Both methods focus on the current state of an epidemic and provide short-term metrics which may not capture the epidemiologic drivers. Through a detailed analysis of country and sub-national data, we explore the limitations of the two traditional methods and propose an alternative approach. Methods and Findings We compared outputs of the traditional methods in five countries for which results were published, and applied the numeric and MOT model to India and six districts within India. We discovered three limitations of the current methods for epidemic appraisal: (1) their results failed to identify the key behaviours that drive the epidemic; (2) they were difficult to apply to local epidemics with heterogeneity across district-level administrative units; and (3) the MOT model was highly sensitive to input parameters, many of which required extraction from non-regional sources. We developed an alternative decision-tree framework for HIV epidemic appraisals, based on a qualitative understanding of epidemiologic drivers, and demonstrated its applicability in India. The alternative framework offered a logical algorithm to characterize epidemics; it required minimal but key data. Conclusions Traditional appraisals that utilize the distribution of prevalent and incident HIV infections in the short-term could misguide prevention priorities and potentially impede efforts to halt the trajectory of the HIV epidemic. An approach that characterizes local transmission dynamics provides a potentially more effective tool with which policy makers can design intervention programmes. PMID:22396756

A Figure-of-Merit for Designing High-Performance Inductive Power Transmission Links

PubMed Central

Kiani, Mehdi; Ghovanloo, Maysam

2014-01-01

Power transfer efficiency (PTE) and power delivered to the load (PDL) are two key inductive link design parameters that relate to the power source and driver specs, power loss, transmission range, robustness against misalignment, variations in loading, and interference with other devices. Designers need to strike a delicate balance between these two because designing the link to achieve high PTE will degrade the PDL and vice versa. We are proposing a new figure-of-merit (FoM), which can help designers to find out whether a two-, three-, or four-coil link is appropriate for their particular application and guide them through an iterative design procedure to reach optimal coil geometries based on how they weigh the PTE versus PDL for that application. Three design examples at three different power levels have been presented based on the proposed FoM for implantable microelectronic devices, handheld mobile devices, and electric vehicles. The new FoM suggests that the two-coil links are suitable when the coils are strongly coupled, and a large PDL is needed. Three-coil links are the best when the coils are loosely coupled, the coupling distance varies considerably, and large PDL is necessary. Finally, four-coil links are optimal when the PTE is paramount, the coils are loosely coupled, and their relative distance and alignment are stable. Measurement results support the accuracy of the theoretical design procedure and conclusions. PMID:25382898

A Figure-of-Merit for Designing High-Performance Inductive Power Transmission Links.

PubMed

Kiani, Mehdi; Ghovanloo, Maysam

2012-11-16

Power transfer efficiency (PTE) and power delivered to the load (PDL) are two key inductive link design parameters that relate to the power source and driver specs, power loss, transmission range, robustness against misalignment, variations in loading, and interference with other devices. Designers need to strike a delicate balance between these two because designing the link to achieve high PTE will degrade the PDL and vice versa. We are proposing a new figure-of-merit (FoM), which can help designers to find out whether a two-, three-, or four-coil link is appropriate for their particular application and guide them through an iterative design procedure to reach optimal coil geometries based on how they weigh the PTE versus PDL for that application. Three design examples at three different power levels have been presented based on the proposed FoM for implantable microelectronic devices, handheld mobile devices, and electric vehicles. The new FoM suggests that the two-coil links are suitable when the coils are strongly coupled, and a large PDL is needed. Three-coil links are the best when the coils are loosely coupled, the coupling distance varies considerably, and large PDL is necessary. Finally, four-coil links are optimal when the PTE is paramount, the coils are loosely coupled, and their relative distance and alignment are stable. Measurement results support the accuracy of the theoretical design procedure and conclusions.

Spatial screening methods for evaluating environmental contaminant hazards and exposure vulnerability

NASA Astrophysics Data System (ADS)

Jones, D. K.

2016-12-01

Human and biotic communities are becoming increasingly vulnerable to sea-level rise and severe storms due to climate change. These events enhance the dispersion and concentration of natural and anthropogenic chemicals and pathogenic microorganisms, which could adversely impact the health and resilience of coastal communities and ecosystems in coming years. The U.S. Geological Survey (USGS) has developed spatial screening methods to identify and map contaminant sources and potential exposure pathways for human and ecological receptors. These methods have been applied within the northeastern U.S. to document contaminants of emerging concern, highlight vulnerable communities, and prioritize locations for future sampling campaigns. Integration of this information provides a means to better assess the baseline status of a complex system and the significance of changes in contaminant hazards due to storm-induced (episodic) and sea-level rise (incremental) disturbances. This presentation will provide an overview of a decision support tool developed by the USGS to document contaminants in the environment relative to key receptor populations and historic storm vulnerabilities. The support tool is designed to accommodate a broad array of geologic, land-use, and climatic variables and utilizes public, nationally available data sources to define contaminant sources and storm vulnerabilities. By employing a flexible and adaptable strategy built upon publicly available data, the method can readily be applied to other site selection or landscape evaluation efforts. Examples will be presented including the Sediment-bound Contaminant Resiliency and Response pilot study (see http://toxics.usgs.gov/scorr/), and investigations of endocrine disruption in the Chesapeake Bay. Key limitations and future applications will be discussed in addition to ongoing method developments to accommodate non-coastal disaster scenarios and more refined contaminant definitions.

Volume 4 - Mobile Sources

EPA Pesticide Factsheets

Mobile source reference material for activity data collection from the Emissions Inventory Improvement Program (EIIP). Provides complete methods for collecting key inputs to onroad mobile and nonroad mobile emissions models.

Documenting research with transgender and gender diverse people: protocol for an evidence map and thematic analysis.

PubMed

Marshall, Zack; Welch, Vivian; Thomas, James; Brunger, Fern; Swab, Michelle; Shemilt, Ian; Kaposy, Chris

2017-02-20

There is limited information about how transgender, gender diverse, and Two-Spirit (trans) people have been represented and studied by researchers. The objectives of this study are to (1) map and describe trans research in the social sciences, sciences, humanities, health, education, and business, (2) identify evidence gaps and opportunities for more responsible research with trans people, (3) assess the use of text mining for study identification, and (4) increase access to trans research for key stakeholders through the creation of a web-based evidence map. Study design was informed by community consultations and pilot searches. Eligibility criteria were established to include all original research of any design, including trans people or their health information, and published in English in peer-reviewed journals. A complex electronic search strategy based on relevant concepts in 15 databases was developed to obtain a broad range of results linked to transgender, gender diverse, and Two-Spirit individuals and communities. Searches conducted in early 2015 resulted in 25,242 references after removal of duplicates. Based on the number of references, resources, and an objective to capture upwards of 90% of the existing literature, this study is a good candidate for text mining using Latent Dirichlet Allocation to improve efficiency of the screening process. The following information will be collected for evidence mapping: study topic, study design, methods and data sources, recruitment strategies, sample size, sample demographics, researcher name and affiliation, country where research was conducted, funding source, and year of publication. The proposed research incorporates an extensive search strategy, text mining, and evidence map; it therefore has the potential to build on knowledge in several fields. Review results will increase awareness of existing trans research, identify evidence gaps, and inform strategic research prioritization. Publishing the map online will improve access to research for key stakeholders including community members, policy makers, and healthcare providers. This study will also contribute to knowledge in the area of text mining for study identification by providing an example of how semi-automation performs for screening on title and abstract and on full text.

Design of current source for multi-frequency simultaneous electrical impedance tomography

NASA Astrophysics Data System (ADS)

Han, Bing; Xu, Yanbin; Dong, Feng

2017-09-01

Multi-frequency electrical impedance tomography has been evolving from the frequency-sweep approach to the multi-frequency simultaneous measurement technique which can reduce measuring time and will be increasingly attractive for time-varying biological applications. The accuracy and stability of the current source are the key factors determining the quality of the image reconstruction. This article presents a field programmable gate array-based current source for a multi-frequency simultaneous electrical impedance tomography system. A novel current source circuit was realized by combining the classic current mirror based on the feedback amplifier AD844 with a differential topology. The optimal phase offsets of harmonic sinusoids were obtained through the crest factor analysis. The output characteristics of this current source were evaluated by simulation and actual measurement. The results include the following: (1) the output impedance was compared with one of the Howland pump circuit in simulation, showing comparable performance at low frequencies. However, the proposed current source makes lower demands for resistor tolerance but performs even better at high frequencies. (2) The output impedance in actual measurement below 200 kHz is above 1.3 MΩ and can reach 250 KΩ up to 1 MHz. (3) An experiment based on a biological RC model has been implemented. The mean error for the demodulated impedance amplitude and phase are 0.192% and 0.139°, respectively. Therefore, the proposed current source is wideband, biocompatible, and high precision, which demonstrates great potential to work as a sub-system in the multi-frequency electrical impedance tomography system.

Noise performance of frequency modulation Kelvin force microscopy

PubMed Central

Deresmes, Dominique; Mélin, Thierry

2014-01-01

Summary Noise performance of a phase-locked loop (PLL) based frequency modulation Kelvin force microscope (FM-KFM) is assessed. Noise propagation is modeled step by step throughout the setup using both exact closed loop noise gains and an approximation known as “noise gain” from operational amplifier (OpAmp) design that offers the advantage of decoupling the noise performance study from considerations of stability and ideal loop response. The bandwidth can be chosen depending on how much noise is acceptable and it is shown that stability is not an issue up to a limit that will be discussed. With thermal and detector noise as the only sources, both approaches yield PLL frequency noise expressions equal to the theoretical value for self-oscillating circuits and in agreement with measurement, demonstrating that the PLL components neither modify nor contribute noise. Kelvin output noise is then investigated by modeling the surrounding bias feedback loop. A design rule is proposed that allows choosing the AC modulation frequency for optimized sharing of the PLL bandwidth between Kelvin and topography loops. A crossover criterion determines as a function of bandwidth, temperature and probe parameters whether thermal or detector noise is the dominating noise source. Probe merit factors for both cases are then established, suggesting how to tackle noise performance by probe design. Typical merit factors of common probe types are compared. This comprehensive study is an encouraging step toward a more integral performance assessment and a remedy against focusing on single aspects and optimizing around randomly chosen key values. PMID:24455457

Bringing Back a Healthy Buzz? Invertebrate Parasites and Reintroductions: A Case Study in Bumblebees.

PubMed

Brown, Mark J F; Sainsbury, Anthony W; Vaughan-Higgins, Rebecca J; Measures, Gavin H; Jones, Catherine M; Gammans, Nikki

2017-03-01

Reintroductions can play a key role in the conservation of endangered species. Parasites may impact reintroductions, both positively and negatively, but few case studies of how to manage parasites during reintroductions exist. Bumblebees are in decline at regional and global scales, and reintroductions can be used to re-establish extinct local populations. Here we report on how the risks associated with parasites are being managed in an ongoing reintroduction of the short-haired bumblebee, Bombus subterraneus, to the UK. Disease risk analysis was conducted and disease risk management plans constructed to design a capture-quarantine-release system that minimised the impacts on both the bumblebees and on their natural parasites. Given that bumblebee parasites are (i) generalists, (ii) geographically ubiquitous, and (iii) show evidence of local adaptation, the disease risk management plan was designed to limit the co-introduction of parasites from the source population in Sweden to the destination site in the UK. Results suggest that this process at best eliminated, or at least severely curtailed the co-introduction of parasites, and ongoing updates of the plan enabled minimization of impacts on natural host-parasite dynamics in the Swedish source population. This study suggests that methods designed for reintroductions of vertebrate species can be successfully applied to invertebrates. Future reintroductions of invertebrates where the parasite fauna is less well known should take advantage of next-generation barcoding and multiple survey years prior to the start of reintroductions, to develop comprehensive disease risk management plans.

On Maximizing the Lifetime of Wireless Sensor Networks by Optimally Assigning Energy Supplies

PubMed Central

Asorey-Cacheda, Rafael; García-Sánchez, Antonio Javier; García-Sánchez, Felipe; García-Haro, Joan; Gonzalez-Castaño, Francisco Javier

2013-01-01

The extension of the network lifetime of Wireless Sensor Networks (WSN) is an important issue that has not been appropriately solved yet. This paper addresses this concern and proposes some techniques to plan an arbitrary WSN. To this end, we suggest a hierarchical network architecture, similar to realistic scenarios, where nodes with renewable energy sources (denoted as primary nodes) carry out most message delivery tasks, and nodes equipped with conventional chemical batteries (denoted as secondary nodes) are those with less communication demands. The key design issue of this network architecture is the development of a new optimization framework to calculate the optimal assignment of renewable energy supplies (primary node assignment) to maximize network lifetime, obtaining the minimum number of energy supplies and their node assignment. We also conduct a second optimization step to additionally minimize the number of packet hops between the source and the sink. In this work, we present an algorithm that approaches the results of the optimization framework, but with much faster execution speed, which is a good alternative for large-scale WSN networks. Finally, the network model, the optimization process and the designed algorithm are further evaluated and validated by means of computer simulation under realistic conditions. The results obtained are discussed comparatively. PMID:23939582

The optical blocking filter for the ATHENA wide field imager: ongoing activities towards the conceptual design

NASA Astrophysics Data System (ADS)

Barbera, M.; Branduardi-Raymont, G.; Collura, A.; Comastri, A.; Eder, J.; Kamisiński, T.; Lo Cicero, U.; Meidinger, N.; Mineo, T.; Molendi, S.; Parodi, G.; Pilch, A.; Piro, L.; Rataj, M.; Rauw, G.; Sciortino, L.; Sciortino, S.; Wawer, P.

2015-08-01

ATHENA is the L2 mission selected by ESA to pursue the science theme "Hot and Energetic Universe" (launch scheduled in 2028). One of the key instruments of ATHENA is the Wide Field Imager (WFI) which will provide imaging in the 0.1-15 keV band over a 40'x40' large field of view, together with spectrally and time-resolved photon counting. The WFI camera, based on arrays of DEPFET active pixel sensors, is also sensitive to UV/Vis photons. Optically generated electron-hole pairs may degrade the spectral resolution as well as change the energy scale by introducing a signal offset. For this reason, the use of an X-ray transparent optical blocking filter is needed to allow the observation of all type of X-ray sources that present a UV/Visible bright counterpart. In this paper, we describe the main activities that we are carrying on for the conceptual design of the optical blocking filter, that will be mounted on the filter wheel, in order to satisfy the scientific requirements on optical load from bright UV/Vis astrophysical source, to maximize the X-ray transmission, and to withstand the severe acoustic and vibration loads foreseen during launch.

System implications of aperture-shade design for the SIRTF Observatory

NASA Technical Reports Server (NTRS)

Lee, J. H.; Brooks, W. F.; Maa, S.

1987-01-01

The 1-m-aperture Space Infrared Telescope Facility (SIRTF) will operate with a sensitivity limited only by the zodiacal background. This sensitivity requirement places severe restrictions on the amount of stray light which can reach the focal plane from off-axis sources such as the sun or earth limb. In addition, radiation from these sources can degrade the lifetime of the telescope and instrument cryogenic system which is now planned for two years before the first servicing. Since the aperture of the telescope represents a break in the telescope insulation system and is effectively the first element in the optical train, the aperture shade is a key system component. The mass, length, and temperature of the shade should be minimized to reduce system cost while maximizing the telescope lifetime and stray light performance. The independent geometric parameters that characterize an asymmetrical shade for a 600 km, 28 deg orbit were identified, and the system sensitivity to the three most important shade parameters were explored. Despite the higher heat loads compared to previously studied polar orbit missions, the analysis determined that passive radiators of a reasonable size are sufficient to meet the system requirements. An optimized design for the SIRTF mission, based on the sensitivity analysis, is proposed.

PopHR: a knowledge-based platform to support integration, analysis, and visualization of population health data.

PubMed

Shaban-Nejad, Arash; Lavigne, Maxime; Okhmatovskaia, Anya; Buckeridge, David L

2017-01-01

Population health decision makers must consider complex relationships between multiple concepts measured with differential accuracy from heterogeneous data sources. Population health information systems are currently limited in their ability to integrate data and present a coherent portrait of population health. Consequentially, these systems can provide only basic support for decision makers. The Population Health Record (PopHR) is a semantic web application that automates the integration and extraction of massive amounts of heterogeneous data from multiple distributed sources (e.g., administrative data, clinical records, and survey responses) to support the measurement and monitoring of population health and health system performance for a defined population. The design of the PopHR draws on the theories of the determinants of health and evidence-based public health to harmonize and explicitly link information about a population with evidence about the epidemiology and control of chronic diseases. Organizing information in this manner and linking it explicitly to evidence is expected to improve decision making related to the planning, implementation, and evaluation of population health and health system interventions. In this paper, we describe the PopHR platform and discuss the architecture, design, key modules, and its implementation and use. © 2016 New York Academy of Sciences.

Application of the DG-1199 methodology to the ESBWR and ABWR.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kalinich, Donald A.; Gauntt, Randall O.; Walton, Fotini

2010-09-01

Appendix A-5 of Draft Regulatory Guide DG-1199 'Alternative Radiological Source Term for Evaluating Design Basis Accidents at Nuclear Power Reactors' provides guidance - applicable to RADTRAD MSIV leakage models - for scaling containment aerosol concentration to the expected steam dome concentration in order to preserve the simplified use of the Accident Source Term (AST) in assessing containment performance under assumed design basis accident (DBA) conditions. In this study Economic and Safe Boiling Water Reactor (ESBWR) and Advanced Boiling Water Reactor (ABWR) RADTRAD models are developed using the DG-1199, Appendix A-5 guidance. The models were run using RADTRAD v3.03. Low Populationmore » Zone (LPZ), control room (CR), and worst-case 2-hr Exclusion Area Boundary (EAB) doses were calculated and compared to the relevant accident dose criteria in 10 CFR 50.67. For the ESBWR, the dose results were all lower than the MSIV leakage doses calculated by General Electric/Hitachi (GEH) in their licensing technical report. There are no comparable ABWR MSIV leakage doses, however, it should be noted that the ABWR doses are lower than the ESBWR doses. In addition, sensitivity cases were evaluated to ascertain the influence/importance of key input parameters/features of the models.« less

On maximizing the lifetime of Wireless Sensor Networks by optimally assigning energy supplies.

PubMed

Asorey-Cacheda, Rafael; García-Sánchez, Antonio Javier; García-Sánchez, Felipe; García-Haro, Joan; González-Castano, Francisco Javier

2013-08-09

The extension of the network lifetime of Wireless Sensor Networks (WSN) is an important issue that has not been appropriately solved yet. This paper addresses this concern and proposes some techniques to plan an arbitrary WSN. To this end, we suggest a hierarchical network architecture, similar to realistic scenarios, where nodes with renewable energy sources (denoted as primary nodes) carry out most message delivery tasks, and nodes equipped with conventional chemical batteries (denoted as secondary nodes) are those with less communication demands. The key design issue of this network architecture is the development of a new optimization framework to calculate the optimal assignment of renewable energy supplies (primary node assignment) to maximize network lifetime, obtaining the minimum number of energy supplies and their node assignment. We also conduct a second optimization step to additionally minimize the number of packet hops between the source and the sink. In this work, we present an algorithm that approaches the results of the optimization framework, but with much faster execution speed, which is a good alternative for large-scale WSN networks. Finally, the network model, the optimization process and the designed algorithm are further evaluated and validated by means of computer simulation under realistic conditions. The results obtained are discussed comparatively.

Facilitative Components of Collaborative Learning: A Review of Nine Health Research Networks

PubMed Central

Rittner, Jessica Levin; Johnson, Karin E.; Gerteis, Jessie; Miller, Therese

2017-01-01

Objective: Collaborative research networks are increasingly used as an effective mechanism for accelerating knowledge transfer into policy and practice. This paper explored the characteristics and collaborative learning approaches of nine health research networks. Data sources/study setting: Semi-structured interviews with representatives from eight diverse US health services research networks conducted between November 2012 and January 2013 and program evaluation data from a ninth. Study design: The qualitative analysis assessed each network's purpose, duration, funding sources, governance structure, methods used to foster collaboration, and barriers and facilitators to collaborative learning. Data collection: The authors reviewed detailed notes from the interviews to distill salient themes. Principal findings: Face-to-face meetings, intentional facilitation and communication, shared vision, trust among members and willingness to work together were key facilitators of collaborative learning. Competing priorities for members, limited funding and lack of long-term support and geographic dispersion were the main barriers to coordination and collaboration across research network members. Conclusion: The findings illustrate the importance of collaborative learning in research networks and the challenges to evaluating the success of research network functionality. Conducting readiness assessments and developing process and outcome evaluation metrics will advance the design and show the impact of collaborative research networks. PMID:28277202

Design methodology for micro-discrete planar optics with minimum illumination loss for an extended source.

PubMed

Shim, Jongmyeong; Park, Changsu; Lee, Jinhyung; Kang, Shinill

2016-08-08

Recently, studies have examined techniques for modeling the light distribution of light-emitting diodes (LEDs) for various applications owing to their low power consumption, longevity, and light weight. The energy mapping technique, a design method that matches the energy distributions of an LED light source and target area, has been the focus of active research because of its design efficiency and accuracy. However, these studies have not considered the effects of the emitting area of the LED source. Therefore, there are limitations to the design accuracy for small, high-power applications with a short distance between the light source and optical system. A design method for compensating for the light distribution of an extended source after the initial optics design based on a point source was proposed to overcome such limits, but its time-consuming process and limited design accuracy with multiple iterations raised the need for a new design method that considers an extended source in the initial design stage. This study proposed a method for designing discrete planar optics that controls the light distribution and minimizes the optical loss with an extended source and verified the proposed method experimentally. First, the extended source was modeled theoretically, and a design method for discrete planar optics with the optimum groove angle through energy mapping was proposed. To verify the design method, design for the discrete planar optics was achieved for applications in illumination for LED flash. In addition, discrete planar optics for LED illuminance were designed and fabricated to create a uniform illuminance distribution. Optical characterization of these structures showed that the design was optimal; i.e., we plotted the optical losses as a function of the groove angle, and found a clear minimum. Simulations and measurements showed that an efficient optical design was achieved for an extended source.

Using pattern enumeration to accelerate process development and ramp yield

NASA Astrophysics Data System (ADS)

Zhuang, Linda; Pang, Jenny; Xu, Jessy; Tsai, Mengfeng; Wang, Amy; Zhang, Yifan; Sweis, Jason; Lai, Ya-Chieh; Ding, Hua

2016-03-01

During a new technology node process setup phase, foundries do not initially have enough product chip designs to conduct exhaustive process development. Different operational teams use manually designed simple test keys to set up their process flows and recipes. When the very first version of the design rule manual (DRM) is ready, foundries enter the process development phase where new experiment design data is manually created based on these design rules. However, these IP/test keys contain very uniform or simple design structures. This kind of design normally does not contain critical design structures or process unfriendly design patterns that pass design rule checks but are found to be less manufacturable. It is desired to have a method to generate exhaustive test patterns allowed by design rules at development stage to verify the gap of design rule and process. This paper presents a novel method of how to generate test key patterns which contain known problematic patterns as well as any constructs which designers could possibly draw based on current design rules. The enumerated test key patterns will contain the most critical design structures which are allowed by any particular design rule. A layout profiling method is used to do design chip analysis in order to find potential weak points on new incoming products so fab can take preemptive action to avoid yield loss. It can be achieved by comparing different products and leveraging the knowledge learned from previous manufactured chips to find possible yield detractors.

Data format standard for sharing light source measurements

NASA Astrophysics Data System (ADS)

Gregory, G. Groot; Ashdown, Ian; Brandenburg, Willi; Chabaud, Dominique; Dross, Oliver; Gangadhara, Sanjay; Garcia, Kevin; Gauvin, Michael; Hansen, Dirk; Haraguchi, Kei; Hasna, Günther; Jiao, Jianzhong; Kelley, Ryan; Koshel, John; Muschaweck, Julius

2013-09-01

Optical design requires accurate characterization of light sources for computer aided design (CAD) software. Various methods have been used to model sources, from accurate physical models to measurement of light output. It has become common practice for designers to include measured source data for design simulations. Typically, a measured source will contain rays which sample the output distribution of the source. The ray data must then be exported to various formats suitable for import into optical analysis or design software. Source manufacturers are also making measurements of their products and supplying CAD models along with ray data sets for designers. The increasing availability of data has been beneficial to the design community but has caused a large expansion in storage needs for the source manufacturers since each software program uses a unique format to describe the source distribution. In 2012, the Illuminating Engineering Society (IES) formed a working group to understand the data requirements for ray data and recommend a standard file format. The working group included representatives from software companies supplying the analysis and design tools, source measurement companies providing metrology, source manufacturers creating the data and users from the design community. Within one year the working group proposed a file format which was recently approved by the IES for publication as TM-25. This paper will discuss the process used to define the proposed format, highlight some of the significant decisions leading to the format and list the data to be included in the first version of the standard.

Wavelength stabilized DBR high power diode laser using EBL optical confining grating technology

NASA Astrophysics Data System (ADS)

Paoletti, R.; Codato, S.; Coriasso, C.; Gotta, P.; Meneghini, G.; Morello, G.; De Melchiorre, P.; Riva, E.; Rosso, M.; Stano, A.; Gattiglio, M.

2018-02-01

This paper reports a DBR High Power Diode Laser (DBR-HPDL) realization, emitting up to 10W in the 920 nm range. High spectral purity (90% power in about 0.5 nm), and wavelength stability versus injected current (about 5 times more than standard FP laser) candidates DBR-HPDL as a suitable device for wavelength stabilized pump source, and high brightness applications exploiting Wavelength Division Multiplexing. Key design aspect is a multiple-orders Electron Beam Lithography (EBL) optical confining grating, stabilizing on same wafer multiple wavelengths by a manufacturable and reliable technology. Present paper shows preliminary demonstration of wafer with 3 pitches, generating DBRHPDLs 2.5 nm spaced.

Clean Restructuring: Design Elements for Low-Carbon Wholesale Markets and Beyond. A 21st Century Power Partnership Thought Leadership Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shah, Monisha; Valenzuela, Jose Maria; Mora, Hector Alejandro Beltran

Countries around the world are in various stages of reforming and restructuring their power systems to better meet development needs and decarbonization commitments. Changes in technology, business models, societal needs, and environmental goals are increasing pressure on countries to consider improvements to their power systems. This report addresses key issues associated with clean restructuring--the transition from traditional, vertically integrated utilities to competitive wholesale markets that rely increasingly on variable renewable electricity sources, demand response, and other clean energy options. The report also includes case studies from Mexico, Denmark, and Germany to provide real-world examples of clean restructuring from different perspectives.

Vacuum System Upgrade for Extended Q-Range Small-Angle Neutron Scattering Diffractometer (EQ-SANS) at SNS

DOE PAGES

Stone, Christopher M.; Williams, Derrick C.; Price, Jeremy P.

2016-09-23

The Extended Q-Range Small-Angle Neutron Scattering Diffractometer (EQ-SANS) instrument at the Spallation Neutron Source (SNS), Oak Ridge, Tennessee, incorporates a 69m3 detector vessel with a vacuum system which required an upgrade with respect to performance, ease of operation, and maintenance. The upgrade focused on improving pumping performance as well as optimizing system design to minimize opportunity for operational error. This upgrade provided the following practical contributions: Reduced time required to evacuate from atmospheric pressure to 2mTorr from 500-1,000 minutes to 60-70 minutes Provided turn-key automated control with a multi-faceted interlock for personnel and machine safety.

U.S. terrestrial solar cell calibration and measurement procedures

NASA Technical Reports Server (NTRS)

Brandhorst, H. W., Jr.

1978-01-01

An outline is presented of changes in measurement procedures concerning solar cells. Outdoor measurements of cell performance based on pyranometer or pyrheliometer determination of intensity are discouraged. The absolute scale of irradiance is to be adopted as soon as possible. The standard atmosphere conditions are 1000 W/sq m irradiance, temperature 28 C, air mass 1.5, and precipitable water vapor content of 2 cm. The allowable light sources for solar simulation are short arc xenon lamps, pulsed xenon lamps, and dichroic filtered tungsten lamps. Key considerations in the design of a reference cell are considered and approaches for the matching of a reference cell to a test cell or modules are discussed.

Light collection and pulse-shape discrimination in elongated scintillator cells for the PROSPECT reactor antineutrino experiment

DOE PAGES

Ashenfelter, J.; Jaffe, D.; Diwan, M. V.; ...

2015-11-06

A meter-long, 23-liter EJ-309 liquid scintillator detector has been constructed to study the light collection and pulse-shape discrimination performance of elongated scintillator cells for the PROSPECT reactor antineutrino experiment. The magnitude and uniformity of light collection and neutron-gamma discrimination power in the energy range of antineutrino inverse beta decay products have been studied using gamma and spontaneous fission calibration sources deployed along the cell axis. We also study neutron-gamma discrimination and light collection abilities for differing PMT and reflector configurations. As a result, key design features for optimizing MeV-scale response and background rejection capabilities are identified.

Vacuum System Upgrade for Extended Q-Range Small-Angle Neutron Scattering Diffractometer (EQ-SANS) at SNS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stone, Christopher M.; Williams, Derrick C.; Price, Jeremy P.

The Extended Q-Range Small-Angle Neutron Scattering Diffractometer (EQ-SANS) instrument at the Spallation Neutron Source (SNS), Oak Ridge, Tennessee, incorporates a 69m3 detector vessel with a vacuum system which required an upgrade with respect to performance, ease of operation, and maintenance. The upgrade focused on improving pumping performance as well as optimizing system design to minimize opportunity for operational error. This upgrade provided the following practical contributions: Reduced time required to evacuate from atmospheric pressure to 2mTorr from 500-1,000 minutes to 60-70 minutes Provided turn-key automated control with a multi-faceted interlock for personnel and machine safety.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yazawa, Kazuaki; Shakouri, Ali

The energy conversion efficiency of today’s thermoelectric generators is significantly lower than that of conventional mechanical engines. Almost all of the existing research is focused on materials to improve the conversion efficiency. Here we propose a general framework to study the cost-efficiency trade-off for thermoelectric power generation. A key factor is the optimization of thermoelectric modules together with their heat source and heat sinks. Full electrical and thermal co-optimization yield a simple analytical expression for optimum design. Based on this model, power output per unit mass can be maximized. We show that the fractional area coverage of thermoelectric elements inmore » a module could play a significant role in reducing the cost of power generation systems.« less

Displacement interferometry with stabilization of wavelength in air.

PubMed

Lazar, Josef; Holá, Miroslava; Cíp, Ondřej; Cížek, Martin; Hrabina, Jan; Buchta, Zdeněk

2012-12-03

We present a concept of suppression of the influence of variations of the refractive index of air in displacement measuring interferometry. The principle is based on referencing of wavelength of the coherent laser source in atmospheric conditions instead of traditional stabilization of the optical frequency and indirect evaluation of the refractive index of air. The key advantage is in identical beam paths of the position measuring interferometers and the interferometer used for the wavelength stabilization. Design of the optical arrangement presented here to verify the concept is suitable for real interferometric position sensing in technical practice especially where a high resolution measurement within some limited range in atmospheric conditions is needed, e.g. in nanometrology.

Design and realization of intelligent tourism service system based on voice interaction

NASA Astrophysics Data System (ADS)

Hu, Lei-di; Long, Yi; Qian, Cheng-yang; Zhang, Ling; Lv, Guo-nian

2008-10-01

Voice technology is one of the important contents to improve the intelligence and humanization of tourism service system. Combining voice technology, the paper concentrates on application needs and the composition of system to present an overall intelligent tourism service system's framework consisting of presentation layer, Web services layer, and tourism application service layer. On the basis, the paper further elaborated the implementation of the system and its key technologies, including intelligent voice interactive technology, seamless integration technology of multiple data sources, location-perception-based guides' services technology, and tourism safety control technology. Finally, according to the situation of Nanjing tourism, a prototype of Tourism Services System is realized.

Practical aspects of modern interferometry for optical manufacturing quality control: Part 2

NASA Astrophysics Data System (ADS)

Smythe, Robert

2012-07-01

Modern phase shifting interferometers enable the manufacture of optical systems that drive the global economy. Semiconductor chips, solid-state cameras, cell phone cameras, infrared imaging systems, space based satellite imaging and DVD and Blu-Ray disks are all enabled by phase shifting interferometers. Theoretical treatments of data analysis and instrument design advance the technology but often are not helpful towards the practical use of interferometers. An understanding of the parameters that drive system performance is critical to produce useful results. Any interferometer will produce a data map and results; this paper, in three parts, reviews some of the key issues to minimize error sources in that data and provide a valid measurement.

Practical aspects of modern interferometry for optical manufacturing quality control, Part 3

NASA Astrophysics Data System (ADS)

Smythe, Robert A.

2012-09-01

Modern phase shifting interferometers enable the manufacture of optical systems that drive the global economy. Semiconductor chips, solid-state cameras, cell phone cameras, infrared imaging systems, space-based satellite imaging, and DVD and Blu-Ray disks are all enabled by phase-shifting interferometers. Theoretical treatments of data analysis and instrument design advance the technology but often are not helpful toward the practical use of interferometers. An understanding of the parameters that drive the system performance is critical to produce useful results. Any interferometer will produce a data map and results; this paper, in three parts, reviews some of the key issues to minimize error sources in that data and provide a valid measurement.

Policies to Enable Bioenergy Deployment: Key Considerations and Good Practices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smolinksi, Sharon; Cox, Sadie

2016-05-01

Bioenergy is renewable energy generated from biological source materials, and includes electricity, transportation fuels and heating. Source materials are varied types of biomass, including food crops such as corn and sugarcane, non-edible lignocellulosic materials such as agricultural and forestry waste and dedicated crops, and municipal and livestock wastes. Key aspects of policies for bioenergy deployment are presented in this brief as part of the Clean Energy Solutions Center's Clean Energy Policy Brief Series.

A systematic review of cost-effectiveness modeling of pharmaceutical therapies in neuropathic pain: variation in practice, key challenges, and recommendations for the future.

PubMed

Critchlow, Simone; Hirst, Matthew; Akehurst, Ron; Phillips, Ceri; Philips, Zoe; Sullivan, Will; Dunlop, Will C N

2017-02-01

Complexities in the neuropathic-pain care pathway make the condition difficult to manage and difficult to capture in cost-effectiveness models. The aim of this study is to understand, through a systematic review of previous cost-effectiveness studies, some of the key strengths and limitations in data and modeling practices in neuropathic pain. Thus, the aim is to guide future research and practice to improve resource allocation decisions and encourage continued investment to find novel and effective treatments for patients with neuropathic pain. The search strategy was designed to identify peer-reviewed cost-effectiveness evaluations of non-surgical, pharmaceutical therapies for neuropathic pain published since January 2000, accessing five key databases. All identified publications were reviewed and screened according to pre-defined eligibility criteria. Data extraction was designed to reflect key data challenges and approaches to modeling in neuropathic pain and based on published guidelines. The search strategy identified 20 cost-effectiveness analyses meeting the inclusion criteria, of which 14 had original model structures. Cost-effectiveness modeling in neuropathic pain is established and increasing across multiple jurisdictions; however, amongst these studies, there is substantial variation in modeling approach, and there are common limitations. Capturing the effect of treatments upon health outcomes, particularly health-related quality-of-life, is challenging, and the health effects of multiple lines of ineffective treatment, common for patients with neuropathic pain, have not been consistently or robustly modeled. To improve future economic modeling in neuropathic pain, further research is suggested into the effect of multiple lines of treatment and treatment failure upon patient outcomes and subsequent treatment effectiveness; the impact of treatment-emergent adverse events upon patient outcomes; and consistent and appropriate pain measures to inform models. The authors further encourage transparent reporting of inputs used to inform cost-effectiveness models, with robust, comprehensive and clear uncertainty analysis and, where feasible, open-source modeling is encouraged.

Participatory monitoring and evaluation approaches that influence decision-making: lessons from a maternal and newborn study in Eastern Uganda.

PubMed

Kananura, Rornald Muhumuza; Ekirapa-Kiracho, Elizabeth; Paina, Ligia; Bumba, Ahmed; Mulekwa, Godfrey; Nakiganda-Busiku, Dinah; Oo, Htet Nay Lin; Kiwanuka, Suzanne Namusoke; George, Asha; Peters, David H

2017-12-28

The use of participatory monitoring and evaluation (M&E) approaches is important for guiding local decision-making, promoting the implementation of effective interventions and addressing emerging issues in the course of implementation. In this article, we explore how participatory M&E approaches helped to identify key design and implementation issues and how they influenced stakeholders' decision-making in eastern Uganda. The data for this paper is drawn from a retrospective reflection of various M&E approaches used in a maternal and newborn health project that was implemented in three districts in eastern Uganda. The methods included qualitative and quantitative M&E techniques such as  key informant interviews, formal surveys and supportive supervision, as well as participatory approaches, notably participatory impact pathway analysis. At the design stage, the M&E approaches were useful for identifying key local problems and feasible local solutions and informing the activities that were subsequently implemented. During the implementation phase, the M&E approaches provided evidence that informed decision-making and helped identify emerging issues, such as weak implementation by some village health teams, health facility constraints such as poor use of standard guidelines, lack of placenta disposal pits, inadequate fuel for the ambulance at some facilities, and poor care for low birth weight infants. Sharing this information with key stakeholders prompted them to take appropriate actions. For example, the sub-county leadership constructed placenta disposal pits, the district health officer provided fuel for ambulances, and health workers received refresher training and mentorship on how to care for newborns. Diverse sources of information and perspectives can help researchers and decision-makers understand and adapt evidence to contexts for more effective interventions. Supporting districts to have crosscutting, routine information generating and sharing platforms that bring together stakeholders from different sectors is therefore crucial for the successful implementation of complex development interventions.

Triangulation in aetiological epidemiology

PubMed Central

Lawlor, Debbie A; Tilling, Kate; Davey Smith, George

2016-01-01

Abstract Triangulation is the practice of obtaining more reliable answers to research questions through integrating results from several different approaches, where each approach has different key sources of potential bias that are unrelated to each other. With respect to causal questions in aetiological epidemiology, if the results of different approaches all point to the same conclusion, this strengthens confidence in the finding. This is particularly the case when the key sources of bias of some of the approaches would predict that findings would point in opposite directions if they were due to such biases. Where there are inconsistencies, understanding the key sources of bias of each approach can help to identify what further research is required to address the causal question. The aim of this paper is to illustrate how triangulation might be used to improve causal inference in aetiological epidemiology. We propose a minimum set of criteria for use in triangulation in aetiological epidemiology, summarize the key sources of bias of several approaches and describe how these might be integrated within a triangulation framework. We emphasize the importance of being explicit about the expected direction of bias within each approach, whenever this is possible, and seeking to identify approaches that would be expected to bias the true causal effect in different directions. We also note the importance, when comparing results, of taking account of differences in the duration and timing of exposures. We provide three examples to illustrate these points. PMID:28108528

Controlling Continuous-Variable Quantum Key Distribution with Entanglement in the Middle Using Tunable Linear Optics Cloning Machines

NASA Astrophysics Data System (ADS)

Wu, Xiao Dong; Chen, Feng; Wu, Xiang Hua; Guo, Ying

2017-02-01

Continuous-variable quantum key distribution (CVQKD) can provide detection efficiency, as compared to discrete-variable quantum key distribution (DVQKD). In this paper, we demonstrate a controllable CVQKD with the entangled source in the middle, contrast to the traditional point-to-point CVQKD where the entanglement source is usually created by one honest party and the Gaussian noise added on the reference partner of the reconciliation is uncontrollable. In order to harmonize the additive noise that originates in the middle to resist the effect of malicious eavesdropper, we propose a controllable CVQKD protocol by performing a tunable linear optics cloning machine (LOCM) at one participant's side, say Alice. Simulation results show that we can achieve the optimal secret key rates by selecting the parameters of the tuned LOCM in the derived regions.

Quantity and source of dietary protein influence metabolite production by gut microbiota and rectal mucosa gene expression: a randomized, parallel, double-blind trial in overweight humans.

PubMed

Beaumont, Martin; Portune, Kevin Joseph; Steuer, Nils; Lan, Annaïg; Cerrudo, Victor; Audebert, Marc; Dumont, Florent; Mancano, Giulia; Khodorova, Nadezda; Andriamihaja, Mireille; Airinei, Gheorghe; Tomé, Daniel; Benamouzig, Robert; Davila, Anne-Marie; Claus, Sandrine Paule; Sanz, Yolanda; Blachier, François

2017-10-01

Background: Although high-protein diets (HPDs) are frequently consumed for body-weight control, little is known about the consequences for gut microbiota composition and metabolic activity and for large intestine mucosal homeostasis. Moreover, the effects of HPDs according to the source of protein need to be considered in this context. Objective: The objective of this study was to evaluate the effects of the quantity and source of dietary protein on microbiota composition, bacterial metabolite production, and consequences for the large intestinal mucosa in humans. Design: A randomized, double-blind, parallel-design trial was conducted in 38 overweight individuals who received a 3-wk isocaloric supplementation with casein, soy protein, or maltodextrin as a control. Fecal and rectal biopsy-associated microbiota composition was analyzed by 16S ribosomal DNA sequencing. Fecal, urinary, and plasma metabolomes were assessed by 1 H-nuclear magnetic resonance. Mucosal transcriptome in rectal biopsies was determined with the use of microarrays. Results: HPDs did not alter the microbiota composition, but induced a shift in bacterial metabolism toward amino acid degradation with different metabolite profiles according to the protein source. Correlation analysis identified new potential bacterial taxa involved in amino acid degradation. Fecal water cytotoxicity was not modified by HPDs, but was associated with a specific microbiota and bacterial metabolite profile. Casein and soy protein HPDs did not induce inflammation, but differentially modified the expression of genes playing key roles in homeostatic processes in rectal mucosa, such as cell cycle or cell death. Conclusions: This human intervention study shows that the quantity and source of dietary proteins act as regulators of gut microbiota metabolite production and host gene expression in the rectal mucosa, raising new questions on the impact of HPDs on the large intestine mucosa homeostasis. This trial was registered at clinicaltrials.gov as NCT02351297. © 2017 American Society for Nutrition.

49 CFR Appendix B to Part 564 - Information To Be Submitted for Long Life Replaceable Light Sources of Limited Definition

Code of Federal Regulations, 2011 CFR

2011-10-01

.... A. Angular locations, diameters, key/keyway sizes, and any other interchangeability dimensions for... base in the bulb holder such as tabs, keys, keyways, surface, etc. III. Bulb Holder Interchangeability Dimensions and Tolerances. A. Mating angular locations, diameters, key/keyway sizes, any other...

49 CFR Appendix B to Part 564 - Information To Be Submitted for Long Life Replaceable Light Sources of Limited Definition

Code of Federal Regulations, 2012 CFR

2012-10-01

.... A. Angular locations, diameters, key/keyway sizes, and any other interchangeability dimensions for... base in the bulb holder such as tabs, keys, keyways, surface, etc. III. Bulb Holder Interchangeability Dimensions and Tolerances. A. Mating angular locations, diameters, key/keyway sizes, any other...

Advances in the Applications of Polyhydroxyalkanoate Nanoparticles for Novel Drug Delivery System

PubMed Central

Shrivastav, Anupama; Kim, Hae-Yeong; Kim, Young-Rok

2013-01-01

Drug delivery technology is emerging as an interdisciplinary science aimed at improving human health. The controlled delivery of pharmacologically active agents to the specific site of action at the therapeutically optimal rate and dose regimen has been a major goal in designing drug delivery systems. Over the past few decades, there has been considerable interest in developing biodegradable drug carriers as effective drug delivery systems. Polymeric materials from natural sources play an important role in controlled release of drug at a particular site. Polyhydroxyalkanoates, due to their origin from natural sources, are given attention as candidates for drug delivery materials. Biodegradable and biocompatible polyhydroxyalkanoates are linear polyesters produced by microorganisms under unbalanced growth conditions, which have emerged as potential polymers for use as biomedical materials for drug delivery due to their unique physiochemical and mechanical properties. This review summarizes many of the key findings in the applications of polyhydroxyalkanoates and polyhydroxyalkanoate nanoparticles for drug delivery system. PMID:23984383

Provenance Usage in the OceanLink Project

NASA Astrophysics Data System (ADS)

Narock, T.; Arko, R. A.; Carbotte, S. M.; Chandler, C. L.; Cheatham, M.; Fils, D.; Finin, T.; Hitzler, P.; Janowicz, K.; Jones, M.; Krisnadhi, A.; Lehnert, K. A.; Mickle, A.; Raymond, L. M.; Schildhauer, M.; Shepherd, A.; Wiebe, P. H.

2014-12-01

A wide spectrum of maturing methods and tools, collectively characterized as the Semantic Web, is helping to vastly improve thedissemination of scientific research. The OceanLink project, an NSF EarthCube Building Block, is utilizing semantic technologies tointegrate geoscience data repositories, library holdings, conference abstracts, and funded research awards. Provenance is a vital componentin meeting both the scientific and engineering requirements of OceanLink. Provenance plays a key role in justification and understanding when presenting users with results aggregated from multiple sources. In the engineering sense, provenance enables the identification of new data and the ability to determine which data sources to query. Additionally, OceanLink will leverage human and machine computation for crowdsourcing, text mining, and co-reference resolution. The results of these computations, and their associated provenance, will be folded back into the constituent systems to continually enhance precision and utility. We will touch on the various roles provenance is playing in OceanLink as well as present our use of the PROV Ontology and associated Ontology Design Patterns.

Assessment of the impact of traditional septic tank soakaway systems on water quality in Ireland.

PubMed

Keegan, Mary; Kilroy, Kate; Nolan, Daniel; Dubber, Donata; Johnston, Paul M; Misstear, Bruce D R; O'Flaherty, Vincent; Barrett, Maria; Gill, Laurence W

2014-01-01

One of the key threats to groundwater and surface water quality in Ireland is the impact of poorly designed, constructed or maintained on-site wastewater treatment systems. An extensive study was carried out to quantify the impact of existing sites on water quality. Six existing sites, consisting of a traditional septic tank and soakaway system, located in various ranges of subsoil permeabilities were identified and monitored to determine how well they function under varying subsoil and weather conditions. The preliminary results of the chemical and microbiological pollutant attenuation in the subsoil of the systems have been assessed and treatment performance evaluated, as well as impact on local surface water and groundwater quality. The source of any faecal contamination detected in groundwater, nearby surface water and effluent samples was confirmed by microbial source tracking. From this, it can be seen that the transport and treatment of percolate vary greatly depending on the permeability and composition of the subsoil.

Development of a time synchronization methodology for a wireless seismic array

NASA Astrophysics Data System (ADS)

Moure-García, David; Torres-González, Pedro; del Río, Joaquín; Mihai, Daniel; Domínguez Cerdeña, Itahiza

2017-04-01

Seismic arrays have multiple applications. In the past, the main use was nuclear tests monitoring that began in mid-twentieth century. The major difference with a seismic network is the hypocenter location procedure. With a seismic network the hypocenter's 3D coordinates are calculated while using an array, the source direction of the seismic signal is determined. Seismic arrays are used in volcanology to obtain the source azimuth of volcanic signals related to fluids movement, magma and/or gases, that do not show a clear seismic phases' onset. A key condition in the seismic array operativity is the temporal synchronization of all the sensors, better than 1 microsecond. Because of that, usually all sensors are connected to the acquisition system by cable to ensure an identical sampling time. In this work we present the design of a wireless low-cost and low-power consumption volcanic monitoring seismic array where all nodes (sensors) acquire data synchronously and transmit them to the center node where a coherent signal is pursued in near real time.

Making your skin crawl: The role of tactile sensitivity in disease avoidance.

PubMed

Hunt, David Francis; Cannell, Grace; Davenhill, Nicholas A; Horsford, Stephanie A; Fleischman, Diana S; Park, Justin H

2017-07-01

Mounting evidence indicates that animals, including humans, have evolved a behavioral disease-avoidance system designed to facilitate the detection and avoidance of sources of pathogens, and that this system interacts with physiological defenses. The skin acts as an important anatomical barrier, yet little research has investigated the role of tactile sensitivity in disease avoidance. Increased tactile sensitivity in the presence of potential sources of pathogens may facilitate prophylactic behaviors such as self-grooming. Across multiple studies, we tested the hypothesis that the induction of disgust-the key emotion underlying disease avoidance-may lead to greater tactile sensitivity compared to control conditions. A nonsignificant trend was found in a pilot study, which was replicated (and found to be significant) in Studies 1 and 2. To our knowledge, these results are the first to demonstrate disgust-induced changes in tactile sensitivity, and they contribute to the growing literature on the integrated evolved defenses against infectious disease. Copyright © 2017 Elsevier B.V. All rights reserved.

Detector-device-independent quantum secret sharing with source flaws.

PubMed

Yang, Xiuqing; Wei, Kejin; Ma, Haiqiang; Liu, Hongwei; Yin, Zhenqiang; Cao, Zhu; Wu, Lingan

2018-04-10

Measurement-device-independent entanglement witness (MDI-EW) plays an important role for detecting entanglement with untrusted measurement device. We present a double blinding-attack on a quantum secret sharing (QSS) protocol based on GHZ state. Using the MDI-EW method, we propose a QSS protocol against all detector side-channels. We allow source flaws in practical QSS system, so that Charlie can securely distribute a key between the two agents Alice and Bob over long distances. Our protocol provides condition on the extracted key rate for the secret against both external eavesdropper and arbitrary dishonest participants. A tight bound for collective attacks can provide good bounds on the practical QSS with source flaws. Then we show through numerical simulations that using single-photon source a secure QSS over 136 km can be achieved.

Online Sources for Competitor Information.

ERIC Educational Resources Information Center

Weiss, Arthur

Competitor information gathering is a key aspect of business planning. Information can be collected from either published or unpublished sources. Unpublished information will often be verified based on material from published sources. Published information is more likely to be factual and includes financial, stockmarket, press, market and…

Passive state preparation in the Gaussian-modulated coherent-states quantum key distribution

DOE Office of Scientific and Technical Information (OSTI.GOV)

Qi, Bing; Evans, Philip G.; Grice, Warren P.

In the Gaussian-modulated coherent-states (GMCS) quantum key distribution (QKD) protocol, Alice prepares quantum states actively: For each transmission, Alice generates a pair of Gaussian-distributed random numbers, encodes them on a weak coherent pulse using optical amplitude and phase modulators, and then transmits the Gaussian-modulated weak coherent pulse to Bob. Here we propose a passive state preparation scheme using a thermal source. In our scheme, Alice splits the output of a thermal source into two spatial modes using a beam splitter. She measures one mode locally using conjugate optical homodyne detectors, and transmits the other mode to Bob after applying appropriatemore » optical attenuation. Under normal conditions, Alice's measurement results are correlated to Bob's, and they can work out a secure key, as in the active state preparation scheme. Given the initial thermal state generated by the source is strong enough, this scheme can tolerate high detector noise at Alice's side. Furthermore, the output of the source does not need to be single mode, since an optical homodyne detector can selectively measure a single mode determined by the local oscillator. Preliminary experimental results suggest that the proposed scheme could be implemented using an off-the-shelf amplified spontaneous emission source.« less

Passive state preparation in the Gaussian-modulated coherent-states quantum key distribution

DOE PAGES

Qi, Bing; Evans, Philip G.; Grice, Warren P.

2018-01-01

In the Gaussian-modulated coherent-states (GMCS) quantum key distribution (QKD) protocol, Alice prepares quantum states actively: For each transmission, Alice generates a pair of Gaussian-distributed random numbers, encodes them on a weak coherent pulse using optical amplitude and phase modulators, and then transmits the Gaussian-modulated weak coherent pulse to Bob. Here we propose a passive state preparation scheme using a thermal source. In our scheme, Alice splits the output of a thermal source into two spatial modes using a beam splitter. She measures one mode locally using conjugate optical homodyne detectors, and transmits the other mode to Bob after applying appropriatemore » optical attenuation. Under normal conditions, Alice's measurement results are correlated to Bob's, and they can work out a secure key, as in the active state preparation scheme. Given the initial thermal state generated by the source is strong enough, this scheme can tolerate high detector noise at Alice's side. Furthermore, the output of the source does not need to be single mode, since an optical homodyne detector can selectively measure a single mode determined by the local oscillator. Preliminary experimental results suggest that the proposed scheme could be implemented using an off-the-shelf amplified spontaneous emission source.« less