Using Satellite Observations to Evaluate the AeroCOM Volcanic Emissions Inventory and the Dispersal of Volcanic SO2 Clouds in MERRA

NASA Technical Reports Server (NTRS)

Hughes, Eric J.; Krotkov, Nickolay; da Silva, Arlindo; Colarco, Peter

2015-01-01

Simulation of volcanic emissions in climate models requires information that describes the eruption of the emissions into the atmosphere. While the total amount of gases and aerosols released from a volcanic eruption can be readily estimated from satellite observations, information about the source parameters, like injection altitude, eruption time and duration, is often not directly known. The AeroCOM volcanic emissions inventory provides estimates of eruption source parameters and has been used to initialize volcanic emissions in reanalysis projects, like MERRA. The AeroCOM volcanic emission inventory provides an eruptions daily SO2 flux and plume top altitude, yet an eruption can be very short lived, lasting only a few hours, and emit clouds at multiple altitudes. Case studies comparing the satellite observed dispersal of volcanic SO2 clouds to simulations in MERRA have shown mixed results. Some cases show good agreement with observations Okmok (2008), while for other eruptions the observed initial SO2 mass is half of that in the simulations, Sierra Negra (2005). In other cases, the initial SO2 amount agrees with the observations but shows very different dispersal rates, Soufriere Hills (2006). In the aviation hazards community, deriving accurate source terms is crucial for monitoring and short-term forecasting (24-h) of volcanic clouds. Back trajectory methods have been developed which use satellite observations and transport models to estimate the injection altitude, eruption time, and eruption duration of observed volcanic clouds. These methods can provide eruption timing estimates on a 2-hour temporal resolution and estimate the altitude and depth of a volcanic cloud. To better understand the differences between MERRA simulations and volcanic SO2 observations, back trajectory methods are used to estimate the source term parameters for a few volcanic eruptions and compared to their corresponding entry in the AeroCOM volcanic emission inventory. The nature of these mixed results is discussed with respect to the source term estimates.

A consistent modelling methodology for secondary settling tanks: a reliable numerical method.

PubMed

Bürger, Raimund; Diehl, Stefan; Farås, Sebastian; Nopens, Ingmar; Torfs, Elena

2013-01-01

The consistent modelling methodology for secondary settling tanks (SSTs) leads to a partial differential equation (PDE) of nonlinear convection-diffusion type as a one-dimensional model for the solids concentration as a function of depth and time. This PDE includes a flux that depends discontinuously on spatial position modelling hindered settling and bulk flows, a singular source term describing the feed mechanism, a degenerating term accounting for sediment compressibility, and a dispersion term for turbulence. In addition, the solution itself is discontinuous. A consistent, reliable and robust numerical method that properly handles these difficulties is presented. Many constitutive relations for hindered settling, compression and dispersion can be used within the model, allowing the user to switch on and off effects of interest depending on the modelling goal as well as investigate the suitability of certain constitutive expressions. Simulations show the effect of the dispersion term on effluent suspended solids and total sludge mass in the SST. The focus is on correct implementation whereas calibration and validation are not pursued.

Oceanic dispersion of Fukushima-derived Cs-137 in the coastal, offshore, and open oceans simulated by multiple oceanic general circulation models

NASA Astrophysics Data System (ADS)

Kawamura, H.; Furuno, A.; Kobayashi, T.; In, T.; Nakayama, T.; Ishikawa, Y.; Miyazawa, Y.; Usui, N.

2017-12-01

To understand the concentration and amount of Fukushima-derived Cs-137 in the ocean, this study simulates the oceanic dispersion of Cs-137 by an oceanic dispersion model SEA-GEARN-FDM developed at Japan Atomic Energy Agency (JAEA) and multiple oceanic general circulation models. The Cs-137 deposition amounts at the sea surface were used as the source term in oceanic dispersion simulations, which were estimated by atmospheric dispersion simulations with a Worldwide version of System for Prediction of Environmental Emergency Dose Information version II (WSPEEDI-II) developed at JAEA. The direct release from the Fukushima Daiichi Nuclear Power Plant into the ocean based on in situ Cs-137 measurements was used as the other source term in oceanic dispersion simulations. The simulated air Cs-137 concentrations qualitatively replicated those measured around the North Pacific. The accumulated Cs-137 ground deposition amount in the eastern Japanese Islands was consistent with that estimated by aircraft measurements. The oceanic dispersion simulations relatively well reproduced the measured Cs-137 concentrations in the coastal and offshore oceans during the first few months after the Fukushima disaster, and in the open ocean during the first year post-disaster. It was suggested that Cs-137 dispersed along the coast in the north-south direction during the first few months post-disaster, and were subsequently dispersed offshore by the Kuroshio Current and Kuroshio Extension. Mesoscale eddies accompanied by the Kuroshio Current and Kuroshio Extension played an important role in dilution of Cs-137. The Cs-137 amounts were quantified in the coastal, offshore, and open oceans during the first year post-disaster. It was demonstrated that Cs-137 actively dispersed from the coastal and offshore oceans to the open ocean, and from the surface layer to the deeper layer in the North Pacific.

Numerical simulations of LNG vapor dispersion in Brayton Fire Training Field tests with ANSYS CFX.

PubMed

Qi, Ruifeng; Ng, Dedy; Cormier, Benjamin R; Mannan, M Sam

2010-11-15

Federal safety regulations require the use of validated consequence models to determine the vapor cloud dispersion exclusion zones for accidental liquefied natural gas (LNG) releases. One tool that is being developed in industry for exclusion zone determination and LNG vapor dispersion modeling is computational fluid dynamics (CFD). This paper uses the ANSYS CFX CFD code to model LNG vapor dispersion in the atmosphere. Discussed are important parameters that are essential inputs to the ANSYS CFX simulations, including the atmospheric conditions, LNG evaporation rate and pool area, turbulence in the source term, ground surface temperature and roughness height, and effects of obstacles. A sensitivity analysis was conducted to illustrate uncertainties in the simulation results arising from the mesh size and source term turbulence intensity. In addition, a set of medium-scale LNG spill tests were performed at the Brayton Fire Training Field to collect data for validating the ANSYS CFX prediction results. A comparison of test data with simulation results demonstrated that CFX was able to describe the dense gas behavior of LNG vapor cloud, and its prediction results of downwind gas concentrations close to ground level were in approximate agreement with the test data. Copyright © 2010 Elsevier B.V. All rights reserved.

Detailed source term estimation of the atmospheric release for the Fukushima Daiichi Nuclear Power Station accident by coupling simulations of an atmospheric dispersion model with an improved deposition scheme and oceanic dispersion model

NASA Astrophysics Data System (ADS)

Katata, G.; Chino, M.; Kobayashi, T.; Terada, H.; Ota, M.; Nagai, H.; Kajino, M.; Draxler, R.; Hort, M. C.; Malo, A.; Torii, T.; Sanada, Y.

2015-01-01

Temporal variations in the amount of radionuclides released into the atmosphere during the Fukushima Daiichi Nuclear Power Station (FNPS1) accident and their atmospheric and marine dispersion are essential to evaluate the environmental impacts and resultant radiological doses to the public. In this paper, we estimate the detailed atmospheric releases during the accident using a reverse estimation method which calculates the release rates of radionuclides by comparing measurements of air concentration of a radionuclide or its dose rate in the environment with the ones calculated by atmospheric and oceanic transport, dispersion and deposition models. The atmospheric and oceanic models used are WSPEEDI-II (Worldwide version of System for Prediction of Environmental Emergency Dose Information) and SEA-GEARN-FDM (Finite difference oceanic dispersion model), both developed by the authors. A sophisticated deposition scheme, which deals with dry and fog-water depositions, cloud condensation nuclei (CCN) activation, and subsequent wet scavenging due to mixed-phase cloud microphysics (in-cloud scavenging) for radioactive iodine gas (I2 and CH3I) and other particles (CsI, Cs, and Te), was incorporated into WSPEEDI-II to improve the surface deposition calculations. The results revealed that the major releases of radionuclides due to the FNPS1 accident occurred in the following periods during March 2011: the afternoon of 12 March due to the wet venting and hydrogen explosion at Unit 1, midnight of 14 March when the SRV (safety relief valve) was opened three times at Unit 2, the morning and night of 15 March, and the morning of 16 March. According to the simulation results, the highest radioactive contamination areas around FNPS1 were created from 15 to 16 March by complicated interactions among rainfall, plume movements, and the temporal variation of release rates. The simulation by WSPEEDI-II using the new source term reproduced the local and regional patterns of cumulative surface deposition of total 131I and 137Cs and air dose rate obtained by airborne surveys. The new source term was also tested using three atmospheric dispersion models (Modèle Lagrangien de Dispersion de Particules d'ordre zéro: MLDP0, Hybrid Single Particle Lagrangian Integrated Trajectory Model: HYSPLIT, and Met Office's Numerical Atmospheric-dispersion Modelling Environment: NAME) for regional and global calculations, and the calculated results showed good agreement with observed air concentration and surface deposition of 137Cs in eastern Japan.

Radiological Source Terms for Tank Farms Safety Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

COWLEY, W.L.

2000-06-27

This document provides Unit Liter Dose factors, atmospheric dispersion coefficients, breathing rates and instructions for using and customizing these factors for use in calculating radiological doses for accident analyses in the Hanford Tank Farms.

Short-term emergency response planning and risk assessment via an integrated modeling system for nuclear power plants in complex terrain

NASA Astrophysics Data System (ADS)

Chang, Ni-Bin; Weng, Yu-Chi

2013-03-01

Short-term predictions of potential impacts from accidental release of various radionuclides at nuclear power plants are acutely needed, especially after the Fukushima accident in Japan. An integrated modeling system that provides expert services to assess the consequences of accidental or intentional releases of radioactive materials to the atmosphere has received wide attention. These scenarios can be initiated either by accident due to human, software, or mechanical failures, or from intentional acts such as sabotage and radiological dispersal devices. Stringent action might be required just minutes after the occurrence of accidental or intentional release. To fulfill the basic functions of emergency preparedness and response systems, previous studies seldom consider the suitability of air pollutant dispersion models or the connectivity between source term, dispersion, and exposure assessment models in a holistic context for decision support. Therefore, the Gaussian plume and puff models, which are only suitable for illustrating neutral air pollutants in flat terrain conditional to limited meteorological situations, are frequently used to predict the impact from accidental release of industrial sources. In situations with complex terrain or special meteorological conditions, the proposing emergency response actions might be questionable and even intractable to decisionmakers responsible for maintaining public health and environmental quality. This study is a preliminary effort to integrate the source term, dispersion, and exposure assessment models into a Spatial Decision Support System (SDSS) to tackle the complex issues for short-term emergency response planning and risk assessment at nuclear power plants. Through a series model screening procedures, we found that the diagnostic (objective) wind field model with the aid of sufficient on-site meteorological monitoring data was the most applicable model to promptly address the trend of local wind field patterns. However, most of the hazardous materials being released into the environment from nuclear power plants are not neutral pollutants, so the particle and multi-segment puff models can be regarded as the most suitable models to incorporate into the output of the diagnostic wind field model in a modern emergency preparedness and response system. The proposed SDSS illustrates the state-of-the-art system design based on the situation of complex terrain in South Taiwan. This system design of SDSS with 3-dimensional animation capability using a tailored source term model in connection with ArcView® Geographical Information System map layers and remote sensing images is useful for meeting the design goal of nuclear power plants located in complex terrain.

Frequent long-distance plant colonization in the changing Arctic.

PubMed

Alsos, Inger Greve; Eidesen, Pernille Bronken; Ehrich, Dorothee; Skrede, Inger; Westergaard, Kristine; Jacobsen, Gro Hilde; Landvik, Jon Y; Taberlet, Pierre; Brochmann, Christian

2007-06-15

The ability of species to track their ecological niche after climate change is a major source of uncertainty in predicting their future distribution. By analyzing DNA fingerprinting (amplified fragment-length polymorphism) of nine plant species, we show that long-distance colonization of a remote arctic archipelago, Svalbard, has occurred repeatedly and from several source regions. Propagules are likely carried by wind and drifting sea ice. The genetic effect of restricted colonization was strongly correlated with the temperature requirements of the species, indicating that establishment limits distribution more than dispersal. Thus, it may be appropriate to assume unlimited dispersal when predicting long-term range shifts in the Arctic.

A previously unreported type of seismic source in the firn layer of the East Antarctic Ice Sheet

NASA Astrophysics Data System (ADS)

Lough, Amanda C.; Barcheck, C. Grace; Wiens, Douglas A.; Nyblade, Andrew; Anandakrishnan, Sridhar

2015-11-01

We identify a unique type of seismic source in the uppermost part of the East Antarctic Ice Sheet recorded by temporary broadband seismic arrays in East Antarctica. These sources, termed "firnquakes," are characterized by dispersed surface wave trains with frequencies of 1-10 Hz detectable at distances up to 1000 km. Events show strong dispersed Rayleigh wave trains and an absence of observable body wave arrivals; most events also show weaker Love waves. Initial events were discovered by standard detection schemes; additional events were then detected with a correlation scanner using the initial arrivals as templates. We locate sources by determining the L2 misfit for a grid of potential source locations using Rayleigh wave arrival times and polarization directions. We then perform a multiple-filter analysis to calculate the Rayleigh wave group velocity dispersion and invert the group velocity for shear velocity structure. The resulting velocity structure is used as an input model to calculate synthetic seismograms. Inverting the dispersion curves yields ice velocity structures consistent with a low-velocity firn layer ~100 m thick and show that velocity structure is laterally variable. The absence of observable body wave phases and the relative amplitudes of Rayleigh waves and noise constrain the source depth to be less than 20 m. The presence of Love waves for most events suggests the source is not isotropic. We propose the events are linked to the formation of small crevasses in the firn, and several events correlate with shallow crevasse fields mapped in satellite imagery.

Interaction between air pollution dispersion and residential heating demands

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lipfert, F.W.; Moskowitz, P.D.; Dungan, J.

The effect of the short-term correlation of a specific emission (sulfur dioxide) from residential space heating, with air pollution dispersion rates on the accuracy of model estimates of urban air pollution on a seasonal or annual basis is analyzed. Hourly climatological and residential emission estimates for six U.S. cities and a simplified area source-dispersion model based on a circular receptor grid are used. The effect on annual average concentration estimations is found to be slight (approximately + or - 12 percent), while the maximum hourly concentrations are shown to vary considerably more, since maximum heat demand and worst-case dispersion aremore » not coincident. Accounting for the correlations between heating demand and dispersion makes possible a differentiation in air pollution potential between coastal and interior cities.« less

Detailed source term estimation of atmospheric release during the Fukushima Dai-ichi nuclear power plant accident by coupling atmospheric and oceanic dispersion models

NASA Astrophysics Data System (ADS)

Katata, Genki; Chino, Masamichi; Terada, Hiroaki; Kobayashi, Takuya; Ota, Masakazu; Nagai, Haruyasu; Kajino, Mizuo

2014-05-01

Temporal variations of release amounts of radionuclides during the Fukushima Dai-ichi Nuclear Power Plant (FNPP1) accident and their dispersion process are essential to evaluate the environmental impacts and resultant radiological doses to the public. Here, we estimated a detailed time trend of atmospheric releases during the accident by combining environmental monitoring data and coupling atmospheric and oceanic dispersion simulations by WSPEEDI-II (Worldwide version of System for Prediction of Environmental Emergency Dose Information) and SEA-GEARN developed by the authors. New schemes for wet, dry, and fog depositions of radioactive iodine gas (I2 and CH3I) and other particles (I-131, Te-132, Cs-137, and Cs-134) were incorporated into WSPEEDI-II. The deposition calculated by WSPEEDI-II was used as input data of ocean dispersion calculations by SEA-GEARN. The reverse estimation method based on the simulation by both models assuming unit release rate (1 Bq h-1) was adopted to estimate the source term at the FNPP1 using air dose rate, and air sea surface concentrations. The results suggested that the major release of radionuclides from the FNPP1 occurred in the following periods during March 2011: afternoon on the 12th when the venting and hydrogen explosion occurred at Unit 1, morning on the 13th after the venting event at Unit 3, midnight on the 14th when several openings of SRV (steam relief valve) were conducted at Unit 2, morning and night on the 15th, and morning on the 16th. The modified WSPEEDI-II using the newly estimated source term well reproduced local and regional patterns of air dose rate and surface deposition of I-131 and Cs-137 obtained by airborne observations. Our dispersion simulations also revealed that the highest radioactive contamination areas around FNPP1 were created from 15th to 16th March by complicated interactions among rainfall (wet deposition), plume movements, and phase properties (gas or particle) of I-131 and release rates associated with reactor pressure variations in Units 2 and 3.

Study of SPM tolerances of electronically compensated DML based systems.

PubMed

Papagiannakis, I; Klonidis, D; Birbas, Alexios N; Kikidis, J; Tomkos, I

2009-05-25

This paper experimentally investigates the effectiveness of electronic dispersion compensation (EDC) for signals limited by self phase modulation (SPM) and various dispersion levels. The sources considered are low-cost conventional directly modulated lasers (DMLs), fabricated for operation at 2.5 Gb/s but modulated at 10 Gb/s. Performance improvement is achieved by means of electronic feed-forward and decision-feedback equalization (FFE/DFE) at the receiver end. Experimental studies consider both transient and adiabatic chirp dominated DMLs sources. The improvement is evaluated in terms of required optical signal-to-noise ratio (ROSNR) for bit-error-rate (BER) values of 10(-3) versus launch power over uncompensated links of standard single mode fiber (SSMF).

Instantaneous and time-averaged dispersion and measurement models for estimation theory applications with elevated point source plumes

NASA Technical Reports Server (NTRS)

Diamante, J. M.; Englar, T. S., Jr.; Jazwinski, A. H.

1977-01-01

Estimation theory, which originated in guidance and control research, is applied to the analysis of air quality measurements and atmospheric dispersion models to provide reliable area-wide air quality estimates. A method for low dimensional modeling (in terms of the estimation state vector) of the instantaneous and time-average pollutant distributions is discussed. In particular, the fluctuating plume model of Gifford (1959) is extended to provide an expression for the instantaneous concentration due to an elevated point source. Individual models are also developed for all parameters in the instantaneous and the time-average plume equations, including the stochastic properties of the instantaneous fluctuating plume.

The development of radioactive sample surrogates for training and exercises

DOE Office of Scientific and Technical Information (OSTI.GOV)

Martha Finck; Bevin Brush; Dick Jansen

2012-03-01

The development of radioactive sample surrogates for training and exercises Source term information is required for to reconstruct a device used in a dispersed radiological dispersal device. Simulating a radioactive environment to train and exercise sampling and sample characterization methods with suitable sample materials is a continued challenge. The Idaho National Laboratory has developed and permitted a Radioactive Response Training Range (RRTR), an 800 acre test range that is approved for open air dispersal of activated KBr, for training first responders in the entry and exit from radioactively contaminated areas, and testing protocols for environmental sampling and field characterization. Membersmore » from the Department of Defense, Law Enforcement, and the Department of Energy participated in the first contamination exercise that was conducted at the RRTR in the July 2011. The range was contaminated using a short lived radioactive Br-82 isotope (activated KBr). Soil samples contaminated with KBr (dispersed as a solution) and glass particles containing activated potassium bromide that emulated dispersed radioactive materials (such as ceramic-based sealed source materials) were collected to assess environmental sampling and characterization techniques. This presentation summarizes the performance of a radioactive materials surrogate for use as a training aide for nuclear forensics.« less

Detailed source term estimation of the atmospheric release for the Fukushima Daiichi Nuclear Power Station accident by coupling simulations of atmospheric dispersion model with improved deposition scheme and oceanic dispersion model

NASA Astrophysics Data System (ADS)

Katata, G.; Chino, M.; Kobayashi, T.; Terada, H.; Ota, M.; Nagai, H.; Kajino, M.; Draxler, R.; Hort, M. C.; Malo, A.; Torii, T.; Sanada, Y.

2014-06-01

Temporal variations in the amount of radionuclides released into the atmosphere during the Fukushima Dai-ichi Nuclear Power Station (FNPS1) accident and their atmospheric and marine dispersion are essential to evaluate the environmental impacts and resultant radiological doses to the public. In this paper, we estimate a detailed time trend of atmospheric releases during the accident by combining environmental monitoring data with atmospheric model simulations from WSPEEDI-II (Worldwide version of System for Prediction of Environmental Emergency Dose Information), and simulations from the oceanic dispersion model SEA-GEARN-FDM, both developed by the authors. A sophisticated deposition scheme, which deals with dry and fogwater depositions, cloud condensation nuclei (CCN) activation and subsequent wet scavenging due to mixed-phase cloud microphysics (in-cloud scavenging) for radioactive iodine gas (I2 and CH3I) and other particles (CsI, Cs, and Te), was incorporated into WSPEEDI-II to improve the surface deposition calculations. The fallout to the ocean surface calculated by WSPEEDI-II was used as input data for the SEA-GEARN-FDM calculations. Reverse and inverse source-term estimation methods based on coupling the simulations from both models was adopted using air dose rates and concentrations, and sea surface concentrations. The results revealed that the major releases of radionuclides due to FNPS1 accident occurred in the following periods during March 2011: the afternoon of 12 March due to the wet venting and hydrogen explosion at Unit 1, the morning of 13 March after the venting event at Unit 3, midnight of 14 March when the SRV (Safely Relief Valve) at Unit 2 was opened three times, the morning and night of 15 March, and the morning of 16 March. According to the simulation results, the highest radioactive contamination areas around FNPS1 were created from 15 to 16 March by complicated interactions among rainfall, plume movements, and the temporal variation of release rates associated with reactor pressure changes in Units 2 and 3. The modified WSPEEDI-II simulation using the new source term reproduced local and regional patterns of cumulative surface deposition of total 131I and 137Cs and air dose rate obtained by airborne surveys. The new source term was also tested using three atmospheric dispersion models (MLDP0, HYSPLIT, and NAME) for regional and global calculations and showed good agreement between calculated and observed air concentration and surface deposition of 137Cs in East Japan. Moreover, HYSPLIT model using the new source term also reproduced the plume arrivals at several countries abroad showing a good correlation with measured air concentration data. A large part of deposition pattern of total 131I and 137Cs in East Japan was explained by in-cloud particulate scavenging. However, for the regional scale contaminated areas, there were large uncertainties due to the overestimation of rainfall amounts and the underestimation of fogwater and drizzle depositions. The computations showed that approximately 27% of 137Cs discharged from FNPS1 deposited to the land in East Japan, mostly in forest areas.

Dispersal of arbuscular mycorrhizal fungi and plants during succession

NASA Astrophysics Data System (ADS)

García de León, David; Moora, Mari; Öpik, Maarja; Jairus, Teele; Neuenkamp, Lena; Vasar, Martti; Bueno, C. Guillermo; Gerz, Maret; Davison, John; Zobel, Martin

2016-11-01

Arbuscular mycorrhizal (AM) fungi are important root symbionts that enhance plant nutrient uptake and tolerance to pathogens and drought. While the role of plant dispersal in shaping successional vegetation is well studied, there is very little information about the dispersal abilities of AM fungi. We conducted a trap-box experiment in a recently abandoned quarry at 10 different distances from the quarry edge (i.e. the potential propagule source) over eleven months to assess the short term, within-year, arrival of plant and AM fungal assemblages and hence their dispersal abilities. Using DNA based techniques we identified AM fungal taxa and analyzed their phylogenetic diversity. Plant diversity was determined by transporting trap soil to a greenhouse and identifying emerging seedlings. We recorded 30 AM fungal taxa. These contained a high proportion of ruderal AM fungi (30% of taxa, 79% of sequences) but the richness and abundance of AM fungi were not related to the distance from the presumed propagule source. The number of sequences of AM fungi decreased over time. Twenty seven plant species (30% of them ruderal) were recorded from the soil seed traps. Plant diversity decreased with distance from the propagule source and increased over time. Our data show that AM fungi with ruderal traits can be fast colonizers of early successional habitats.

Ultrafine particles dispersion modeling in a street canyon: development and evaluation of a composite lattice Boltzmann model.

PubMed

Habilomatis, George; Chaloulakou, Archontoula

2013-10-01

Recently, a branch of particulate matter research concerns on ultrafine particles found in the urban environment, which originate, to a significant extent, from traffic sources. In urban street canyons, dispersion of ultrafine particles affects pedestrian's short term exposure and resident's long term exposure as well. The aim of the present work is the development and the evaluation of a composite lattice Boltzmann model to study the dispersion of ultrafine particles, in urban street canyon microenvironment. The proposed model has the potential to penetrate into the physics of this complex system. In order to evaluate the model performance against suitable experimental data, ultrafine particles levels have been monitored on an hourly basis for a period of 35 days, in a street canyon, in Athens area. The results of the comparative analysis are quite satisfactory. Furthermore, our modeled results are in a good agreement with the results of other computational and experimental studies. This work is a first attempt to study the dispersion of an air pollutant by application of the lattice Boltzmann method. Copyright © 2013 Elsevier B.V. All rights reserved.

Seed dispersal by wind, birds, and bats between Philippine montane rainforest and successional vegetation.

PubMed

Ingle, Nina M R

2003-01-01

In the moist Neotropics, vertebrate frugivores have a much greater role in the dispersal of forest and successional woody plants than wind, and bats rather than birds play the dominant role in dispersing early successional species. I investigated whether these patterns also occurred in a Philippine montane rainforest and adjacent successional vegetation. I also asked whether seed mass was related to probability of dispersal between habitats. A greater number of woody species and stems in the forest produced vertebrate-dispersed seeds than wind-dispersed seeds. Although input of forest seeds into the successional area was dominated by vertebrate-dispersed seeds in terms of species richness, wind-dispersed seeds landed in densities 15 times higher. Frugivorous birds dispersed more forest seeds and species into the successional area than bats, and more successional seeds and species into the forest. As expected, seed input declined with distance from source habitat. Low input of forest seeds into the successional area at the farthest distance sampled, 40 m from forest edge, particularly for vertebrate-dispersed seeds, suggests very limited dispersal out of forest even into a habitat in which woody successional vegetation provides perches and fruit resources. For species of vertebrate-dispersed successional seeds, probability of dispersal into forest declined significantly with seed mass.

Integration of measurements with atmospheric dispersion models: Source term estimation for dispersal of (239)Pu due to non-nuclear detonation of high explosive

NASA Astrophysics Data System (ADS)

Edwards, L. L.; Harvey, T. F.; Freis, R. P.; Pitovranov, S. E.; Chernokozhin, E. V.

1992-10-01

The accuracy associated with assessing the environmental consequences of an accidental release of radioactivity is highly dependent on our knowledge of the source term characteristics and, in the case when the radioactivity is condensed on particles, the particle size distribution, all of which are generally poorly known. This paper reports on the development of a numerical technique that integrates the radiological measurements with atmospheric dispersion modeling. This results in a more accurate particle-size distribution and particle injection height estimation when compared with measurements of high explosive dispersal of (239)Pu. The estimation model is based on a non-linear least squares regression scheme coupled with the ARAC three-dimensional atmospheric dispersion models. The viability of the approach is evaluated by estimation of ADPIC model input parameters such as the ADPIC particle size mean aerodynamic diameter, the geometric standard deviation, and largest size. Additionally we estimate an optimal 'coupling coefficient' between the particles and an explosive cloud rise model. The experimental data are taken from the Clean Slate 1 field experiment conducted during 1963 at the Tonopah Test Range in Nevada. The regression technique optimizes the agreement between the measured and model predicted concentrations of (239)Pu by varying the model input parameters within their respective ranges of uncertainties. The technique generally estimated the measured concentrations within a factor of 1.5, with the worst estimate being within a factor of 5, very good in view of the complexity of the concentration measurements, the uncertainties associated with the meteorological data, and the limitations of the models. The best fit also suggest a smaller mean diameter and a smaller geometric standard deviation on the particle size as well as a slightly weaker particle to cloud coupling than previously reported.

Fast Running Urban Dispersion Model for Radiological Dispersal Device (RDD) Releases: Model Description and Validation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gowardhan, Akshay; Neuscamman, Stephanie; Donetti, John

Aeolus is an efficient three-dimensional computational fluid dynamics code based on finite volume method developed for predicting transport and dispersion of contaminants in a complex urban area. It solves the time dependent incompressible Navier-Stokes equation on a regular Cartesian staggered grid using a fractional step method. It also solves a scalar transport equation for temperature and using the Boussinesq approximation. The model also includes a Lagrangian dispersion model for predicting the transport and dispersion of atmospheric contaminants. The model can be run in an efficient Reynolds Average Navier-Stokes (RANS) mode with a run time of several minutes, or a moremore » detailed Large Eddy Simulation (LES) mode with run time of hours for a typical simulation. This report describes the model components, including details on the physics models used in the code, as well as several model validation efforts. Aeolus wind and dispersion predictions are compared to field data from the Joint Urban Field Trials 2003 conducted in Oklahoma City (Allwine et al 2004) including both continuous and instantaneous releases. Newly implemented Aeolus capabilities include a decay chain model and an explosive Radiological Dispersal Device (RDD) source term; these capabilities are described. Aeolus predictions using the buoyant explosive RDD source are validated against two experimental data sets: the Green Field explosive cloud rise experiments conducted in Israel (Sharon et al 2012) and the Full-Scale RDD Field Trials conducted in Canada (Green et al 2016).« less

Evaluating Force-Field London Dispersion Coefficients Using the Exchange-Hole Dipole Moment Model.

PubMed

Mohebifar, Mohamad; Johnson, Erin R; Rowley, Christopher N

2017-12-12

London dispersion interactions play an integral role in materials science and biophysics. Force fields for atomistic molecular simulations typically represent dispersion interactions by the 12-6 Lennard-Jones potential using empirically determined parameters. These parameters are generally underdetermined, and there is no straightforward way to test if they are physically realistic. Alternatively, the exchange-hole dipole moment (XDM) model from density-functional theory predicts atomic and molecular London dispersion coefficients from first principles, providing an innovative strategy to validate the dispersion terms of molecular-mechanical force fields. In this work, the XDM model was used to obtain the London dispersion coefficients of 88 organic molecules relevant to biochemistry and pharmaceutical chemistry and the values compared with those derived from the Lennard-Jones parameters of the CGenFF, GAFF, OPLS, and Drude polarizable force fields. The molecular dispersion coefficients for the CGenFF, GAFF, and OPLS models are systematically higher than the XDM-calculated values by a factor of roughly 1.5, likely due to neglect of higher order dispersion terms and premature truncation of the dispersion-energy summation. The XDM dispersion coefficients span a large range for some molecular-mechanical atom types, suggesting an unrecognized source of error in force-field models, which assume that atoms of the same type have the same dispersion interactions. Agreement with the XDM dispersion coefficients is even poorer for the Drude polarizable force field. Popular water models were also examined, and TIP3P was found to have dispersion coefficients similar to the experimental and XDM references, although other models employ anomalously high values. Finally, XDM-derived dispersion coefficients were used to parametrize molecular-mechanical force fields for five liquids-benzene, toluene, cyclohexane, n-pentane, and n-hexane-which resulted in improved accuracy in the computed enthalpies of vaporization despite only having to evaluate a much smaller section of the parameter space.

Source-Sink Colonization as a Possible Strategy of Insects Living in Temporary Habitats.

PubMed

Frouz, Jan; Kindlmann, Pavel

2015-01-01

Continuous colonization and re-colonization is critical for survival of insect species living in temporary habitats. When insect populations in temporary habitats are depleted, some species may escape extinction by surviving in permanent, but less suitable habitats, in which long-term population survival can be maintained only by immigration from other populations. Such situation has been repeatedly described in nature, but conditions when and how this occurs and how important this phenomenon is for insect metapopulation survival are still poorly known, mainly because it is difficult to study experimentally. Therefore, we used a simulation model to investigate, how environmental stochasticity, growth rate and the incidence of dispersal affect the positive effect of permanent but poor ("sink") habitats on the likelihood of metapopulation persistence in a network of high quality but temporary ("source") habitats. This model revealed that permanent habitats substantially increase the probability of metapopulation persistence of insect species with poor dispersal ability if the availability of temporary habitats is spatio-temporally synchronized. Addition of permanent habitats to a system sometimes enabled metapopulation persistence even in cases in which the metapopulation would otherwise go extinct, especially for species with high growth rates. For insect species with low growth rates the probability of a metapopulation persistence strongly depended on the proportions of "source" to "source" and "sink" to "source" dispersal rates.

Improving volcanic sulfur dioxide cloud dispersal forecasts by progressive assimilation of satellite observations

NASA Astrophysics Data System (ADS)

Boichu, Marie; Clarisse, Lieven; Khvorostyanov, Dmitry; Clerbaux, Cathy

2014-04-01

Forecasting the dispersal of volcanic clouds during an eruption is of primary importance, especially for ensuring aviation safety. As volcanic emissions are characterized by rapid variations of emission rate and height, the (generally) high level of uncertainty in the emission parameters represents a critical issue that limits the robustness of volcanic cloud dispersal forecasts. An inverse modeling scheme, combining satellite observations of the volcanic cloud with a regional chemistry-transport model, allows reconstructing this source term at high temporal resolution. We demonstrate here how a progressive assimilation of freshly acquired satellite observations, via such an inverse modeling procedure, allows for delivering robust sulfur dioxide (SO2) cloud dispersal forecasts during the eruption. This approach provides a computationally cheap estimate of the expected location and mass loading of volcanic clouds, including the identification of SO2-rich parts.

HIGH-PRECISION ASTROMETRIC MILLIMETER VERY LONG BASELINE INTERFEROMETRY USING A NEW METHOD FOR ATMOSPHERIC CALIBRATION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rioja, M.; Dodson, R., E-mail: maria.rioja@icrar.org

2011-04-15

We describe a new method which achieves high-precision very long baseline interferometry (VLBI) astrometry in observations at millimeter (mm) wavelengths. It combines fast frequency-switching observations, to correct for the dominant non-dispersive tropospheric fluctuations, with slow source-switching observations, for the remaining ionospheric dispersive terms. We call this method source-frequency phase referencing. Provided that the switching cycles match the properties of the propagation media, one can recover the source astrometry. We present an analytic description of the two-step calibration strategy, along with an error analysis to characterize its performance. Also, we provide observational demonstrations of a successful application with observations using themore » Very Long Baseline Array at 86 GHz of the pairs of sources 3C274 and 3C273 and 1308+326 and 1308+328 under various conditions. We conclude that this method is widely applicable to mm-VLBI observations of many target sources, and unique in providing bona fide astrometrically registered images and high-precision relative astrometric measurements in mm-VLBI using existing and newly built instruments, including space VLBI.« less

Investigating the effects of the fixed and varying dispersion parameters of Poisson-gamma models on empirical Bayes estimates.

PubMed

Lord, Dominique; Park, Peter Young-Jin

2008-07-01

Traditionally, transportation safety analysts have used the empirical Bayes (EB) method to improve the estimate of the long-term mean of individual sites; to correct for the regression-to-the-mean (RTM) bias in before-after studies; and to identify hotspots or high risk locations. The EB method combines two different sources of information: (1) the expected number of crashes estimated via crash prediction models, and (2) the observed number of crashes at individual sites. Crash prediction models have traditionally been estimated using a negative binomial (NB) (or Poisson-gamma) modeling framework due to the over-dispersion commonly found in crash data. A weight factor is used to assign the relative influence of each source of information on the EB estimate. This factor is estimated using the mean and variance functions of the NB model. With recent trends that illustrated the dispersion parameter to be dependent upon the covariates of NB models, especially for traffic flow-only models, as well as varying as a function of different time-periods, there is a need to determine how these models may affect EB estimates. The objectives of this study are to examine how commonly used functional forms as well as fixed and time-varying dispersion parameters affect the EB estimates. To accomplish the study objectives, several traffic flow-only crash prediction models were estimated using a sample of rural three-legged intersections located in California. Two types of aggregated and time-specific models were produced: (1) the traditional NB model with a fixed dispersion parameter and (2) the generalized NB model (GNB) with a time-varying dispersion parameter, which is also dependent upon the covariates of the model. Several statistical methods were used to compare the fitting performance of the various functional forms. The results of the study show that the selection of the functional form of NB models has an important effect on EB estimates both in terms of estimated values, weight factors, and dispersion parameters. Time-specific models with a varying dispersion parameter provide better statistical performance in terms of goodness-of-fit (GOF) than aggregated multi-year models. Furthermore, the identification of hazardous sites, using the EB method, can be significantly affected when a GNB model with a time-varying dispersion parameter is used. Thus, erroneously selecting a functional form may lead to select the wrong sites for treatment. The study concludes that transportation safety analysts should not automatically use an existing functional form for modeling motor vehicle crashes without conducting rigorous analyses to estimate the most appropriate functional form linking crashes with traffic flow.

Inverse modelling of radionuclide release rates using gamma dose rate observations

NASA Astrophysics Data System (ADS)

Hamburger, Thomas; Evangeliou, Nikolaos; Stohl, Andreas; von Haustein, Christoph; Thummerer, Severin; Wallner, Christian

2015-04-01

Severe accidents in nuclear power plants such as the historical accident in Chernobyl 1986 or the more recent disaster in the Fukushima Dai-ichi nuclear power plant in 2011 have drastic impacts on the population and environment. Observations and dispersion modelling of the released radionuclides help to assess the regional impact of such nuclear accidents. Modelling the increase of regional radionuclide activity concentrations, which results from nuclear accidents, underlies a multiplicity of uncertainties. One of the most significant uncertainties is the estimation of the source term. That is, the time dependent quantification of the released spectrum of radionuclides during the course of the nuclear accident. The quantification of the source term may either remain uncertain (e.g. Chernobyl, Devell et al., 1995) or rely on estimates given by the operators of the nuclear power plant. Precise measurements are mostly missing due to practical limitations during the accident. The release rates of radionuclides at the accident site can be estimated using inverse modelling (Davoine and Bocquet, 2007). The accuracy of the method depends amongst others on the availability, reliability and the resolution in time and space of the used observations. Radionuclide activity concentrations are observed on a relatively sparse grid and the temporal resolution of available data may be low within the order of hours or a day. Gamma dose rates, on the other hand, are observed routinely on a much denser grid and higher temporal resolution and provide therefore a wider basis for inverse modelling (Saunier et al., 2013). We present a new inversion approach, which combines an atmospheric dispersion model and observations of radionuclide activity concentrations and gamma dose rates to obtain the source term of radionuclides. We use the Lagrangian particle dispersion model FLEXPART (Stohl et al., 1998; Stohl et al., 2005) to model the atmospheric transport of the released radionuclides. The inversion method uses a Bayesian formulation considering uncertainties for the a priori source term and the observations (Eckhardt et al., 2008, Stohl et al., 2012). The a priori information on the source term is a first guess. The gamma dose rate observations are used to improve the first guess and to retrieve a reliable source term. The details of this method will be presented at the conference. This work is funded by the Bundesamt für Strahlenschutz BfS, Forschungsvorhaben 3612S60026. References Davoine, X. and Bocquet, M., Atmos. Chem. Phys., 7, 1549-1564, 2007. Devell, L., et al., OCDE/GD(96)12, 1995. Eckhardt, S., et al., Atmos. Chem. Phys., 8, 3881-3897, 2008. Saunier, O., et al., Atmos. Chem. Phys., 13, 11403-11421, 2013. Stohl, A., et al., Atmos. Environ., 32, 4245-4264, 1998. Stohl, A., et al., Atmos. Chem. Phys., 5, 2461-2474, 2005. Stohl, A., et al., Atmos. Chem. Phys., 12, 2313-2343, 2012.

TESTING U.S. EPA'S ISCST -VERSION 3 MODEL ON DIOXINS: A COMPARISON OF PREDICTED AND OBSERVED AIR AND SOIL CONCENTRATIONS

EPA Science Inventory

The central purpose of our study was to examine the performance of the United States Environmental Protection Agency's (EPA) nonreactive Gaussian air quality dispersion model, the Industrial Source Complex Short Term Model (ISCST3) Version 98226, in predicting polychlorinated dib...

A simulated approach to estimating PM10 and PM2.5 concentrations downwind from cotton gins

USDA-ARS?s Scientific Manuscript database

Cotton gins are required to obtain operating permits from state air pollution regulatory agencies (SAPRA), which regulate the amount of particulate matter that can be emitted. Industrial Source Complex Short Term version 3 (ISCST3) is the Gaussian dispersion model currently used by some SAPRAs to pr...

Enhancing thermal conductivity of fluids with graphite nanoparticles and carbon nanotube

DOEpatents

Zhang, Zhiqiang [Lexington, KY; Lockwood, Frances E [Georgetown, KY

2008-03-25

A fluid media such as oil or water, and a selected effective amount of carbon nanomaterials necessary to enhance the thermal conductivity of the fluid. One of the preferred carbon nanomaterials is a high thermal conductivity graphite, exceeding that of the neat fluid to be dispersed therein in thermal conductivity, and ground, milled, or naturally prepared with mean particle size less than 500 nm, and preferably less than 200 nm, and most preferably less than 100 nm. The graphite is dispersed in the fluid by one or more of various methods, including ultrasonication, milling, and chemical dispersion. Carbon nanotubes with graphitic structure is another preferred source of carbon nanomaterial, although other carbon nanomaterials are acceptable. To confer long term stability, the use of one or more chemical dispersants is preferred. The thermal conductivity enhancement, compared to the fluid without carbon nanomaterial, is proportional to the amount of carbon nanomaterials (carbon nanotubes and/or graphite) added.

A Case of Bilateral Pigment Dispersion Syndrome Following Many Years of Uninterrupted Treatment With Atropine 1% for Bilateral Congenital Cataracts.

PubMed

Gizzi, Corrado; Mohamed-Noriega, Jibran; Murdoch, Ian

2017-10-01

Describe an unusual case of bilateral pigment dispersion syndrome (PDS) following years of uninterrupted treatment with atropine 1% for bilateral congenital cataracts, speculate on potential mechanisms leading to this condition. This is a case report. A 45-year-old white patient on long-term treatment with atropine 1% ointment since his infancy for bilateral congenital cataracts developed PDS with secondary ocular hypertension. The patient showed all the hallmarks of PDS with secondary ocular hypertension. An anterior segment Swept-Source optical coherence tomography was obtained to review the iris profile. The patient showed good pressure response to topical prostaglandin therapy. This is the second case report of PDS in a patient with chronic use of topical atropine. The proposed mechanisms for pigment dispersion are discussed and the possibility raised of dispersion being a potential side effect of the drug.

Climate change and climate systems influence and control the atmospheric dispersion of desert dust: implications for human health

USGS Publications Warehouse

Griffin, Dale W.; Ragaini, Richard C.

2010-01-01

The global dispersion of desert dust through Earth’s atmosphere is greatly influenced by temperature. Temporal analyses of ice core data have demonstrated that enhanced dust dispersion occurs during glacial events. This is due to an increase in ice cover, which results in an increase in drier terrestrial cover. A shorter temporal analysis of dust dispersion data over the last 40 years has demonstrated an increase in dust transport. Climate systems or events such as the North Atlantic Oscillation, the Indian Ocean subtropical High, Pacific Decadal Oscillation, and El Nino-Sothern Oscillation are known to influence global short-term dust dispersion occurrence and transport routes. Anthropogenic influences on dust transport include deforestation, harmful use of topsoil for agriculture as observed during the American Dust Bowl period, and the creation of dry seas (Aral Sea) and lakes (Lake Owens in California and Lake Chad in North Africa) through the diversion of source waters (for irrigation and drinking water supplies). Constituents of desert dust both from source regions (pathogenic microorganisms, organic and inorganic toxins) and those scavenged through atmospheric transport (i.e., industrial and agricultural emissions) are known to directly impact human and ecosystem health. This presentation will present a review of global scale dust storms and how these events can be both a detriment and benefit to various organisms in downwind environments.

Distributions of occupied and vacant butterfly habitats in fragmented landscapes.

PubMed

Thomas, C D; Thomas, J A; Warren, M S

1992-12-01

We found several rare UK butterflies to be restricted to relatively large and non-isolated habitat patches, while small patches and those that are isolated from population sources remain vacant. These patterns of occurrence are generated by the dynamic processes of local extinction and colonization. Habitat patches act as terrestrial archipelagos in which long-term population persistence, and hence effective long-term conservation, rely on networks of suitable habitats, sufficiently close to allow natural dispersal.

Dispersal, deposition and collective doses after the Chernobyl disaster.

PubMed

Fairlie, Ian

2007-01-01

This article discusses the dispersal, deposition and collective doses of the radioactive fallout from the Chernobyl accident. It explains that, although Belarus, Ukraine and Russia were heavily contaminated by the Chernobyl fallout, more than half of the fallout was deposited outside these countries, particularly in Western Europe. Indeed, about 40 per cent of the surface area of Europe was contaminated. Collective doses are predicted to result in 30,000 to 60,000 excess cancer deaths throughout the northern hemisphere, mostly in western Europe. The article also estimates that the caesium-137 source term was about a third higher than official figures.

Inverse modelling of radionuclide release rates using gamma dose rate observations

NASA Astrophysics Data System (ADS)

Hamburger, Thomas; Stohl, Andreas; von Haustein, Christoph; Thummerer, Severin; Wallner, Christian

2014-05-01

Severe accidents in nuclear power plants such as the historical accident in Chernobyl 1986 or the more recent disaster in the Fukushima Dai-ichi nuclear power plant in 2011 have drastic impacts on the population and environment. The hazardous consequences reach out on a national and continental scale. Environmental measurements and methods to model the transport and dispersion of the released radionuclides serve as a platform to assess the regional impact of nuclear accidents - both, for research purposes and, more important, to determine the immediate threat to the population. However, the assessments of the regional radionuclide activity concentrations and the individual exposure to radiation dose underlie several uncertainties. For example, the accurate model representation of wet and dry deposition. One of the most significant uncertainty, however, results from the estimation of the source term. That is, the time dependent quantification of the released spectrum of radionuclides during the course of the nuclear accident. The quantification of the source terms of severe nuclear accidents may either remain uncertain (e.g. Chernobyl, Devell et al., 1995) or rely on rather rough estimates of released key radionuclides given by the operators. Precise measurements are mostly missing due to practical limitations during the accident. Inverse modelling can be used to realise a feasible estimation of the source term (Davoine and Bocquet, 2007). Existing point measurements of radionuclide activity concentrations are therefore combined with atmospheric transport models. The release rates of radionuclides at the accident site are then obtained by improving the agreement between the modelled and observed concentrations (Stohl et al., 2012). The accuracy of the method and hence of the resulting source term depends amongst others on the availability, reliability and the resolution in time and space of the observations. Radionuclide activity concentrations are observed on a relatively sparse grid and the temporal resolution of available data may be low within the order of hours or a day. Gamma dose rates on the other hand are observed routinely on a much denser grid and higher temporal resolution. Gamma dose rate measurements contain no explicit information on the observed spectrum of radionuclides and have to be interpreted carefully. Nevertheless, they provide valuable information for the inverse evaluation of the source term due to their availability (Saunier et al., 2013). We present a new inversion approach combining an atmospheric dispersion model and observations of radionuclide activity concentrations and gamma dose rates to obtain the source term of radionuclides. We use the Lagrangian particle dispersion model FLEXPART (Stohl et al., 1998; Stohl et al., 2005) to model the atmospheric transport of the released radionuclides. The gamma dose rates are calculated from the modelled activity concentrations. The inversion method uses a Bayesian formulation considering uncertainties for the a priori source term and the observations (Eckhardt et al., 2008). The a priori information on the source term is a first guess. The gamma dose rate observations will be used with inverse modelling to improve this first guess and to retrieve a reliable source term. The details of this method will be presented at the conference. This work is funded by the Bundesamt für Strahlenschutz BfS, Forschungsvorhaben 3612S60026. References Davoine, X. and Bocquet, M., Atmos. Chem. Phys., 7, 1549-1564, 2007. Devell, L., et al., OCDE/GD(96)12, 1995. Eckhardt, S., et al., Atmos. Chem. Phys., 8, 3881-3897, 2008. Saunier, O., et al., Atmos. Chem. Phys., 13, 11403-11421, 2013. Stohl, A., et al., Atmos. Environ., 32, 4245-4264, 1998. Stohl, A., et al., Atmos. Chem. Phys., 5, 2461-2474, 2005. Stohl, A., et al., Atmos. Chem. Phys., 12, 2313-2343, 2012.

Human-caused mortality influences spatial population dynamics: pumas in landscapes with varying mortality risks

USGS Publications Warehouse

Newby, Jesse R.; Mills, L. Scott; Ruth, Toni K.; Pletscher, Daniel H.; Mitchell, Michael S.; Quigley, Howard B.; Murphy, Kerry M.; DeSimone, Rich

2013-01-01

An understanding of how stressors affect dispersal attributes and the contribution of local populations to multi-population dynamics are of immediate value to basic and applied ecology. Puma (Puma concolor) populations are expected to be influenced by inter-population movements and susceptible to human-induced source–sink dynamics. Using long-term datasets we quantified the contribution of two puma populations to operationally define them as sources or sinks. The puma population in the Northern Greater Yellowstone Ecosystem (NGYE) was largely insulated from human-induced mortality by Yellowstone National Park. Pumas in the western Montana Garnet Mountain system were exposed to greater human-induced mortality, which changed over the study due to the closure of a 915 km2 area to hunting. The NGYE’s population growth depended on inter-population movements, as did its ability to act as a source to the larger region. The heavily hunted Garnet area was a sink with a declining population until the hunting closure, after which it became a source with positive intrinsic growth and a 16× increase in emigration. We also examined the spatial and temporal characteristics of individual dispersal attributes (emigration, dispersal distance, establishment success) of subadult pumas (N = 126). Human-caused mortality was found to negatively impact all three dispersal components. Our results demonstrate the influence of human-induced mortality on not only within population vital rates, but also inter-population vital rates, affecting the magnitude and mechanisms of local population’s contribution to the larger metapopulation.

Bayesian estimation of a source term of radiation release with approximately known nuclide ratios

NASA Astrophysics Data System (ADS)

Tichý, Ondřej; Šmídl, Václav; Hofman, Radek

2016-04-01

We are concerned with estimation of a source term in case of an accidental release from a known location, e.g. a power plant. Usually, the source term of an accidental release of radiation comprises of a mixture of nuclide. The gamma dose rate measurements do not provide a direct information on the source term composition. However, physical properties of respective nuclide (deposition properties, decay half-life) can be used when uncertain information on nuclide ratios is available, e.g. from known reactor inventory. The proposed method is based on linear inverse model where the observation vector y arise as a linear combination y = Mx of a source-receptor-sensitivity (SRS) matrix M and the source term x. The task is to estimate the unknown source term x. The problem is ill-conditioned and further regularization is needed to obtain a reasonable solution. In this contribution, we assume that nuclide ratios of the release is known with some degree of uncertainty. This knowledge is used to form the prior covariance matrix of the source term x. Due to uncertainty in the ratios the diagonal elements of the covariance matrix are considered to be unknown. Positivity of the source term estimate is guaranteed by using multivariate truncated Gaussian distribution. Following Bayesian approach, we estimate all parameters of the model from the data so that y, M, and known ratios are the only inputs of the method. Since the inference of the model is intractable, we follow the Variational Bayes method yielding an iterative algorithm for estimation of all model parameters. Performance of the method is studied on simulated 6 hour power plant release where 3 nuclide are released and 2 nuclide ratios are approximately known. The comparison with method with unknown nuclide ratios will be given to prove the usefulness of the proposed approach. This research is supported by EEA/Norwegian Financial Mechanism under project MSMT-28477/2014 Source-Term Determination of Radionuclide Releases by Inverse Atmospheric Dispersion Modelling (STRADI).

Optimization of optical properties of photonic crystal fibers infiltrated with carbon tetrachloride for supercontinuum generation with subnanojoule femtosecond pulses.

PubMed

Dinh, Quang Ho; Pniewski, Jacek; Van, Hieu Le; Ramaniuk, Aleksandr; Long, Van Cao; Borzycki, Krzysztof; Xuan, Khoa Dinh; Klimczak, Mariusz; Buczyński, Ryszard

2018-05-10

A photonic crystal fiber (PCF) made of fused silica glass, infiltrated with carbon tetrachloride (CCl 4 ), is proposed as a new source of supercontinuum (SC) light. Guiding properties in terms of effective refractive index, attenuation, and dispersion of the fundamental mode are studied numerically. As a result, two optimized structures are selected and verified against SC generation in detail. The dispersion characteristic of the first structure has the zero-dispersion wavelength at 1.252 μm, while the dispersion characteristic of the second structure is all-normal and equals -4.37  ps·nm -1 ·km -1 at 1.55 μm. SC generation was demonstrated for the wavelengths 1.064 μm, 1.35 μm, and 1.55 μm. We prove the possibility of coherent, octave-spanning SC generation with 300 fs pulses with only 0.8 nJ of energy in-coupled into the core with each of the studied structures. Proposed fibers are fully compatible with all-silica fiber systems and PCFs with wide mode area, and can also be used for all-fiber SC sources. The proposed solution may lead to new low-cost all-fiber optical systems.

Underestimated risks of recurrent long-range ash dispersal from northern Pacific Arc volcanoes

PubMed Central

Bourne, A. J.; Abbott, P. M.; Albert, P. G.; Cook, E.; Pearce, N. J. G.; Ponomareva, V.; Svensson, A.; Davies, S. M.

2016-01-01

Widespread ash dispersal poses a significant natural hazard to society, particularly in relation to disruption to aviation. Assessing the extent of the threat of far-travelled ash clouds on flight paths is substantially hindered by an incomplete volcanic history and an underestimation of the potential reach of distant eruptive centres. The risk of extensive ash clouds to aviation is thus poorly quantified. New evidence is presented of explosive Late Pleistocene eruptions in the Pacific Arc, currently undocumented in the proximal geological record, which dispersed ash up to 8000 km from source. Twelve microscopic ash deposits or cryptotephra, invisible to the naked eye, discovered within Greenland ice-cores, and ranging in age between 11.1 and 83.7 ka b2k, are compositionally matched to northern Pacific Arc sources including Japan, Kamchatka, Cascades and Alaska. Only two cryptotephra deposits are correlated to known high-magnitude eruptions (Towada-H, Japan, ca 15 ka BP and Mount St Helens Set M, ca 28 ka BP). For the remaining 10 deposits, there is no evidence of age- and compositionally-equivalent eruptive events in regional volcanic stratigraphies. This highlights the inherent problem of under-reporting eruptions and the dangers of underestimating the long-term risk of widespread ash dispersal for trans-Pacific and trans-Atlantic flight routes. PMID:27445233

Underestimated risks of recurrent long-range ash dispersal from northern Pacific Arc volcanoes.

PubMed

Bourne, A J; Abbott, P M; Albert, P G; Cook, E; Pearce, N J G; Ponomareva, V; Svensson, A; Davies, S M

2016-07-21

Widespread ash dispersal poses a significant natural hazard to society, particularly in relation to disruption to aviation. Assessing the extent of the threat of far-travelled ash clouds on flight paths is substantially hindered by an incomplete volcanic history and an underestimation of the potential reach of distant eruptive centres. The risk of extensive ash clouds to aviation is thus poorly quantified. New evidence is presented of explosive Late Pleistocene eruptions in the Pacific Arc, currently undocumented in the proximal geological record, which dispersed ash up to 8000 km from source. Twelve microscopic ash deposits or cryptotephra, invisible to the naked eye, discovered within Greenland ice-cores, and ranging in age between 11.1 and 83.7 ka b2k, are compositionally matched to northern Pacific Arc sources including Japan, Kamchatka, Cascades and Alaska. Only two cryptotephra deposits are correlated to known high-magnitude eruptions (Towada-H, Japan, ca 15 ka BP and Mount St Helens Set M, ca 28 ka BP). For the remaining 10 deposits, there is no evidence of age- and compositionally-equivalent eruptive events in regional volcanic stratigraphies. This highlights the inherent problem of under-reporting eruptions and the dangers of underestimating the long-term risk of widespread ash dispersal for trans-Pacific and trans-Atlantic flight routes.

Toxicity of Deepwater Horizon Source Oil and the Chemical Dispersant, Corexit® 9500, to Coral Larvae

PubMed Central

Goodbody-Gringley, Gretchen; Wetzel, Dana L.; Gillon, Daniel; Pulster, Erin; Miller, Allison; Ritchie, Kim B.

2013-01-01

Acute catastrophic events can cause significant damage to marine environments in a short time period and may have devastating long-term impacts. In April 2010 the BP-operated Deepwater Horizon (DWH) offshore oil rig exploded, releasing an estimated 760 million liters of crude oil into the Gulf of Mexico. This study examines the potential effects of oil spill exposure on coral larvae of the Florida Keys. Larvae of the brooding coral, Porites astreoides, and the broadcast spawning coral, Montastraea faveolata, were exposed to multiple concentrations of BP Horizon source oil (crude, weathered and WAF), oil in combination with the dispersant Corexit® 9500 (CEWAF), and dispersant alone, and analyzed for behavior, settlement, and survival. Settlement and survival of P. astreoides and M. faveolata larvae decreased with increasing concentrations of WAF, CEWAF and Corexit® 9500, however the degree of the response varied by species and solution. P. astreoides larvae experienced decreased settlement and survival following exposure to 0.62 ppm source oil, while M. faveolata larvae were negatively impacted by 0.65, 1.34 and 1.5 ppm, suggesting that P. astreoides larvae may be more tolerant to WAF exposure than M. faveolata larvae. Exposure to medium and high concentrations of CEWAF (4.28/18.56 and 30.99/35.76 ppm) and dispersant Corexit® 9500 (50 and 100 ppm), significantly decreased larval settlement and survival for both species. Furthermore, exposure to Corexit® 9500 resulted in settlement failure and complete larval mortality after exposure to 50 and 100 ppm for M. faveolata and 100 ppm for P. astreoides. These results indicate that exposure of coral larvae to oil spill related contaminants, particularly the dispersant Corexit® 9500, has the potential to negatively impact coral settlement and survival, thereby affecting the resilience and recovery of coral reefs following exposure to oil and dispersants. PMID:23326298

The Fukushima releases: an inverse modelling approach to assess the source term by using gamma dose rate observations

NASA Astrophysics Data System (ADS)

Saunier, Olivier; Mathieu, Anne; Didier, Damien; Tombette, Marilyne; Quélo, Denis; Winiarek, Victor; Bocquet, Marc

2013-04-01

The Chernobyl nuclear accident and more recently the Fukushima accident highlighted that the largest source of error on consequences assessment is the source term estimation including the time evolution of the release rate and its distribution between radioisotopes. Inverse modelling methods have proved to be efficient to assess the source term due to accidental situation (Gudiksen, 1989, Krysta and Bocquet, 2007, Stohl et al 2011, Winiarek et al 2012). These methods combine environmental measurements and atmospheric dispersion models. They have been recently applied to the Fukushima accident. Most existing approaches are designed to use air sampling measurements (Winiarek et al, 2012) and some of them use also deposition measurements (Stohl et al, 2012, Winiarek et al, 2013). During the Fukushima accident, such measurements are far less numerous and not as well distributed within Japan than the dose rate measurements. To efficiently document the evolution of the contamination, gamma dose rate measurements were numerous, well distributed within Japan and they offered a high temporal frequency. However, dose rate data are not as easy to use as air sampling measurements and until now they were not used in inverse modelling approach. Indeed, dose rate data results from all the gamma emitters present in the ground and in the atmosphere in the vicinity of the receptor. They do not allow one to determine the isotopic composition or to distinguish the plume contribution from wet deposition. The presented approach proposes a way to use dose rate measurement in inverse modeling approach without the need of a-priori information on emissions. The method proved to be efficient and reliable when applied on the Fukushima accident. The emissions for the 8 main isotopes Xe-133, Cs-134, Cs-136, Cs-137, Ba-137m, I-131, I-132 and Te-132 have been assessed. The Daiichi power plant events (such as ventings, explosions…) known to have caused atmospheric releases are well identified in the retrieved source term, except for unit 3 explosion where no measurement was available. The comparisons between the simulations of atmospheric dispersion and deposition of the retrieved source term show a good agreement with environmental observations. Moreover, an important outcome of this study is that the method proved to be perfectly suited to crisis management and should contribute to improve our response in case of a nuclear accident.

Several braze filler metals for joining an oxide-dispersion-strengthened nickel-chromium-aluminum alloy

NASA Technical Reports Server (NTRS)

Gyorgak, C. A.

1975-01-01

An evaluation was made of five braze filler metals for joining an aluminum-containing oxide dispersion-strengthened (ODS) alloy, TD-NiCrAl. All five braze filler metals evaluated are considered suitable for joining TD-NiCrAl in terms of wettability and flow. Also, the braze alloys appear to be tolerant of slight variations in brazing procedures since joints prepared by three sources using three of the braze filler metals exhibited similar brazing characteristics and essentially equivalent 1100 C stress-rupture properties in a brazed butt-joint configuration. Recommendations are provided for brazing the aluminum-containing ODS alloys.

Bayesian source term determination with unknown covariance of measurements

NASA Astrophysics Data System (ADS)

Belal, Alkomiet; Tichý, Ondřej; Šmídl, Václav

2017-04-01

Determination of a source term of release of a hazardous material into the atmosphere is a very important task for emergency response. We are concerned with the problem of estimation of the source term in the conventional linear inverse problem, y = Mx, where the relationship between the vector of observations y is described using the source-receptor-sensitivity (SRS) matrix M and the unknown source term x. Since the system is typically ill-conditioned, the problem is recast as an optimization problem minR,B(y - Mx)TR-1(y - Mx) + xTB-1x. The first term minimizes the error of the measurements with covariance matrix R, and the second term is a regularization of the source term. There are different types of regularization arising for different choices of matrices R and B, for example, Tikhonov regularization assumes covariance matrix B as the identity matrix multiplied by scalar parameter. In this contribution, we adopt a Bayesian approach to make inference on the unknown source term x as well as unknown R and B. We assume prior on x to be a Gaussian with zero mean and unknown diagonal covariance matrix B. The covariance matrix of the likelihood R is also unknown. We consider two potential choices of the structure of the matrix R. First is the diagonal matrix and the second is a locally correlated structure using information on topology of the measuring network. Since the inference of the model is intractable, iterative variational Bayes algorithm is used for simultaneous estimation of all model parameters. The practical usefulness of our contribution is demonstrated on an application of the resulting algorithm to real data from the European Tracer Experiment (ETEX). This research is supported by EEA/Norwegian Financial Mechanism under project MSMT-28477/2014 Source-Term Determination of Radionuclide Releases by Inverse Atmospheric Dispersion Modelling (STRADI).

Pressure evolution equation for the particulate phase in inhomogeneous compressible disperse multiphase flows

NASA Astrophysics Data System (ADS)

Annamalai, Subramanian; Balachandar, S.; Sridharan, P.; Jackson, T. L.

2017-02-01

An analytical expression describing the unsteady pressure evolution of the dispersed phase driven by variations in the carrier phase is presented. In this article, the term "dispersed phase" represents rigid particles, droplets, or bubbles. Letting both the dispersed and continuous phases be inhomogeneous, unsteady, and compressible, the developed pressure equation describes the particle response and its eventual equilibration with that of the carrier fluid. The study involves impingement of a plane traveling wave of a given frequency and subsequent volume-averaged particle pressure calculation due to a single wave. The ambient or continuous fluid's pressure and density-weighted normal velocity are identified as the source terms governing the particle pressure. Analogous to the generalized Faxén theorem, which is applicable to the particle equation of motion, the pressure expression is also written in terms of the surface average of time-varying incoming flow properties. The surface average allows the current formulation to be generalized for any complex incident flow, including situations where the particle size is comparable to that of the incoming flow. Further, the particle pressure is also found to depend on the dispersed-to-continuous fluid density ratio and speed of sound ratio in addition to dynamic viscosities of both fluids. The model is applied to predict the unsteady pressure variation inside an aluminum particle subjected to normal shock waves. The results are compared against numerical simulations and found to be in good agreement. Furthermore, it is shown that, although the analysis is conducted in the limit of negligible flow Reynolds and Mach numbers, it can be used to compute the density and volume of the dispersed phase to reasonable accuracy. Finally, analogous to the pressure evolution expression, an equation describing the time-dependent particle radius is deduced and is shown to reduce to the Rayleigh-Plesset equation in the linear limit.

Humans as long-distance dispersers of rural plant communities.

PubMed

Auffret, Alistair G; Cousins, Sara A O

2013-01-01

Humans are known for their capacity to disperse organisms long distances. Long-distance dispersal can be important for species threatened by habitat destruction, but research into human-mediated dispersal is often focused upon few and/or invasive species. Here we use citizen science to identify the capacity for humans to disperse seeds on their clothes and footwear from a known species pool in a valuable habitat, allowing for an assessment of the fraction and types of species dispersed by humans in an alternative context. We collected material from volunteers cutting 48 species-rich meadows throughout Sweden. We counted 24,354 seeds of 197 species, representing 34% of the available species pool, including several rare and protected species. However, 71 species (36%) are considered invasive elsewhere in the world. Trait analysis showed that seeds with hooks or other appendages were more likely to be dispersed by humans, as well as those with a persistent seed bank. More activity in a meadow resulted in more dispersal, both in terms of species and representation of the source communities. Average potential dispersal distances were measured at 13 km. We consider humans capable seed dispersers, transporting a significant proportion of the plant communities in which they are active, just like more traditional vectors such as livestock. When rural populations were larger, people might have been regular and effective seed dispersers, and the net rural-urban migration resulting in a reduction in humans in the landscape may have exacerbated the dispersal failure evident in declining plant populations today. With the fragmentation of habitat and changes in land use resulting from agricultural change, and the increased mobility of humans worldwide, the dispersal role of humans may have shifted from providers of regular local and landscape dispersal to providers of much rarer long-distance and regional dispersal, and international invasion.

EXPERIENCES FROM THE SOURCE-TERM ANALYSIS OF A LOW AND INTERMEDIATE LEVEL RADWASTE DISPOSAL FACILITY

DOE Office of Scientific and Technical Information (OSTI.GOV)

Park,Jin Beak; Park, Joo-Wan; Lee, Eun-Young

2003-02-27

Enhancement of a computer code SAGE for evaluation of the Korean concept for a LILW waste disposal facility is discussed. Several features of source term analysis are embedded into SAGE to analyze: (1) effects of degradation mode of an engineered barrier, (2) effects of dispersion phenomena in the unsaturated zone and (3) effects of time dependent sorption coefficient in the unsaturated zone. IAEA's Vault Safety Case (VSC) approach is used to demonstrate the ability of this assessment code. Results of MASCOT are used for comparison purposes. These enhancements of the safety assessment code, SAGE, can contribute to realistic evaluation ofmore » the Korean concept of the LILW disposal project in the near future.« less

Modelling larval dispersal of the king scallop ( Pecten maximus) in the English Channel: examples from the bay of Saint-Brieuc and the bay of Seine

NASA Astrophysics Data System (ADS)

Nicolle, Amandine; Dumas, Franck; Foveau, Aurélie; Foucher, Eric; Thiébaut, Eric

2013-06-01

The king scallop ( Pecten maximus) is one of the most important benthic species of the English Channel as it constitutes the first fishery in terms of landings in this area. To support strategies of spatial fishery management, we develop a high-resolution biophysical model to study scallop dispersal in two bays along the French coasts of the English Channel (i.e. the bay of Saint-Brieuc and the bay of Seine) and to quantify the relative roles of local hydrodynamic processes, temperature-dependent planktonic larval duration (PLD) and active swimming behaviour (SB). The two bays are chosen for three reasons: (1) the distribution of the scallop stocks in these areas is well known from annual scallop stock surveys, (2) these two bays harbour important fisheries and (3) scallops in these two areas present some differences in terms of reproductive cycle and spawning duration. The English Channel currents and temperature are simulated for 10 years (2000-2010) with the MARS-3D code and then used by the Lagrangian module of MARS-3D to model the transport. Results were analysed in terms of larval distribution at settlement and connectivity rates. While larval transport in the two bays depended both on the tidal residual circulation and the wind-induced currents, the relative role of these two hydrodynamic processes varied among bays. In the bay of Saint-Brieuc, the main patterns of larval dispersal were due to tides, the wind being only a source of variability in the extent of larval patch and the local retention rate. Conversely, in the bay of Seine, wind-induced currents altered both the direction and the extent of larval transport. The main effect of a variable PLD in relation to the thermal history of each larva was to reduce the spread of dispersal and consequently increase the local retention by about 10 % on average. Although swimming behaviour could influence larval dispersal during the first days of the PLD when larvae are mainly located in surface waters, it has a minor role on larval distribution at settlement and retention rates. The analysis of the connectivity between subpopulations within each bay allows identifying the main sources of larvae which depend on both the characteristics of local hydrodynamics and the spatial heterogeneity in the reproductive outputs.

Atmospheric dispersion prediction and source estimation of hazardous gas using artificial neural network, particle swarm optimization and expectation maximization

NASA Astrophysics Data System (ADS)

Qiu, Sihang; Chen, Bin; Wang, Rongxiao; Zhu, Zhengqiu; Wang, Yuan; Qiu, Xiaogang

2018-04-01

Hazardous gas leak accident has posed a potential threat to human beings. Predicting atmospheric dispersion and estimating its source become increasingly important in emergency management. Current dispersion prediction and source estimation models cannot satisfy the requirement of emergency management because they are not equipped with high efficiency and accuracy at the same time. In this paper, we develop a fast and accurate dispersion prediction and source estimation method based on artificial neural network (ANN), particle swarm optimization (PSO) and expectation maximization (EM). The novel method uses a large amount of pre-determined scenarios to train the ANN for dispersion prediction, so that the ANN can predict concentration distribution accurately and efficiently. PSO and EM are applied for estimating the source parameters, which can effectively accelerate the process of convergence. The method is verified by the Indianapolis field study with a SF6 release source. The results demonstrate the effectiveness of the method.

Mid-IR supercontinuum generation in ultra-low loss, dispersion-zero shifted tellurite glass fiber with extended coverage beyond 4.5 μm

NASA Astrophysics Data System (ADS)

Thapa, Rajesh; Rhonehouse, Dan; Nguyen, Dan; Wiersma, Kort; Smith, Chris; Zong, Jie; Chavez-Pirson, Arturo

2013-10-01

Mid-infrared sources are a key enabling technology for various applications such as remote chemical sensing, defense communications and countermeasures, and bio-photonic diagnostics and therapeutics. Conventional mid-IR sources include optical parametric amplifiers, quantum cascade lasers, synchrotron and free electron lasers. An all-fiber approach to generate a high power, single mode beam with extremely wide (1μm-5μm) and simultaneous wavelength coverage has significant advantages in terms of reliability (no moving parts or alignment), room temperature operation, size, weight, and power efficiency. Here, we report single mode, high power extended wavelength coverage (1μm to 5μm) supercontinuum generation using a tellurite-based dispersion managed nonlinear fiber and an all-fiber based short pulse (20 ps), single mode pump source. We have developed this mid IR supercontinuum source based on highly purified solid-core tellurite glass fibers that are waveguide engineered for dispersion-zero matching with Tm-doped pulsed fiber laser pumps. The conversion efficiency from 1922nm pump to mid IR (2μm-5μm) supercontinuum is greater than 30%, and approaching 60% for the full spectrum. We have achieved > 1.2W covering from 1μm to 5μm with 2W of pump. In particular, the wavelength region above 4μm has been difficult to cover with supercontinuum sources based on ZBLAN or chalcogenide fibers. In contrast to that, our nonlinear tellurite fibers have a wider transparency window free of unwanted absorption, and are highly suited for extending the long wavelength emission above 4μm. We achieve spectral power density at 4.1μm already exceeding 0.2mW/nm and with potential for higher by scaling of pump power.

Angular dependence of source-target-detector in active mode standoff infrared detection

NASA Astrophysics Data System (ADS)

Pacheco-Londoño, Leonardo C.; Castro-Suarez, John R.; Aparicio-Bolaños, Joaquín. A.; Hernández-Rivera, Samuel P.

2013-06-01

Active mode standoff measurement using infrared spectroscopy were carried out in which the angle between target and the source was varied from 0-70° with respect to the surface normal of substrates containing traces of highly energetic materials (explosives). The experiments were made using three infrared sources: a modulated source (Mod-FTIR), an unmodulated source (UnMod-FTIR) and a scanning quantum cascade laser (QCL), part of a dispersive mid infrared (MIR) spectrometer. The targets consisted of PENT 200 μg/cm2 deposited on aluminum plates placed at 1 m from the sources. The evaluation of the three modalities was aimed at verifying the influence of the highly collimated laser beam in the detection in comparison with the other sources. The Mod-FTIR performed better than QCL source in terms of the MIR signal intensity decrease with increasing angle.

Error estimates for (semi-)empirical dispersion terms and large biomacromolecules.

PubMed

Korth, Martin

2013-10-14

The first-principles modeling of biomaterials has made tremendous advances over the last few years with the ongoing growth of computing power and impressive developments in the application of density functional theory (DFT) codes to large systems. One important step forward was the development of dispersion corrections for DFT methods, which account for the otherwise neglected dispersive van der Waals (vdW) interactions. Approaches at different levels of theory exist, with the most often used (semi-)empirical ones based on pair-wise interatomic C6R(-6) terms. Similar terms are now also used in connection with semiempirical QM (SQM) methods and density functional tight binding methods (SCC-DFTB). Their basic structure equals the attractive term in Lennard-Jones potentials, common to most force field approaches, but they usually use some type of cutoff function to make the mixing of the (long-range) dispersion term with the already existing (short-range) dispersion and exchange-repulsion effects from the electronic structure theory methods possible. All these dispersion approximations were found to perform accurately for smaller systems, but error estimates for larger systems are very rare and completely missing for really large biomolecules. We derive such estimates for the dispersion terms of DFT, SQM and MM methods using error statistics for smaller systems and dispersion contribution estimates for the PDBbind database of protein-ligand interactions. We find that dispersion terms will usually not be a limiting factor for reaching chemical accuracy, though some force fields and large ligand sizes are problematic.

Population genetic evidence for sex-specific dispersal in an inbred social spider.

PubMed

Smith, Deborah R; Su, Yong-Chao; Berger-Tal, Reut; Lubin, Yael

2016-08-01

Dispersal in most group-living species ensures gene flow among groups, but in cooperative social spiders, juvenile dispersal is suppressed and colonies are highly inbred. It has been suggested that such inbred sociality is advantageous in the short term, but likely to lead to extinction or reduced speciation rates in the long run. In this situation, very low levels of dispersal and gene flow among colonies may have unusually important impacts on fitness and persistence of social spiders. We investigated sex-specific differences in dispersal and gene flow among colonies, as reflected in the genetic structure within colonies and populations of the African social spider Stegodyphus dumicola Pocock, 1898 (Eresidae). We used DNA fingerprinting and mtDNA sequence data along with spatial mapping of colonies to compare male and female patterns of relatedness within and among colonies at three study sites. Samples were collected during and shortly after the mating season to detect sex-specific dispersal. Distribution of mtDNA haplotypes was consistent with proliferation of social nests by budding and medium- to long-distance dispersal by ballooning females. Analysis of molecular variance and spatial autocorrelation analyses of AFLPs showed high levels of genetic similarity within colonies, and STRUCTURE analyses revealed that the number of source populations contributing to colonies ranged from one to three. We also showed significant evidence of male dispersal among colonies at one site. These results support the hypothesis that in social spiders, genetic cohesion among populations is maintained by long-distance dispersal of female colony founders. Genetic diversity within colonies is maintained by colony initiation by multiple dispersing females, and adult male dispersal over short distances. Male dispersal may be particularly important in maintaining gene flow among colonies in local populations.

Spectra of cosmic X-ray sources

NASA Technical Reports Server (NTRS)

Holt, S. S.; Mccray, R.

1982-01-01

X-ray measurements provide the most direct probes of astrophysical environments with temperatures exceeding one million K. Progress in experimental research utilizing dispersive techniques (e.g., Bragg and grating spectroscopy) is considerably slower than that in areas utilizing photometric techniques, because of the relative inefficiency of the former for the weak X-ray signals from celestial sources. As a result, the term "spectroscopy" as applied to X-ray astronomy has traditionally satisfied a much less restrictive definition (in terms of resolving power) than it has in other wavebands. Until quite recently, resolving powers of order unity were perfectly respectable, and still provide (in most cases) the most useful spectroscopic data. In the broadest sense, X-ray photometric measurements are spectroscopic, insofar as they represent samples of the overall electromagnetic continua of celestial objects.

Seed dispersal by fishes in tropical and temperate fresh waters: The growing evidence

NASA Astrophysics Data System (ADS)

Horn, Michael H.; Correa, Sandra Bibiana; Parolin, Pia; Pollux, B. J. A.; Anderson, Jill T.; Lucas, Christine; Widmann, Peter; Tjiu, Albertus; Galetti, Mauro; Goulding, Michael

2011-11-01

Fruit-eating by fishes represents an ancient (perhaps Paleozoic) interaction increasingly regarded as important for seed dispersal (ichthyochory) in tropical and temperate ecosystems. Most of the more than 275 known frugivorous species belong to the mainly Neotropical Characiformes (pacus, piranhas) and Siluriformes (catfishes), but cypriniforms (carps, minnows) are more important in the Holarctic and Indomalayan regions. Frugivores are among the most abundant fishes in Neotropical floodplains where they eat the fruits of a wide variety of trees and shrubs. By consuming fruits, fishes gain access to rich sources of carbohydrates, lipids and proteins and act as either seed predators or seed dispersers. With their often high mobility, large size, and great longevity, fruit-eating fishes can play important roles as seed dispersers and exert strong influences on local plant-recruitment dynamics and regional biodiversity. Recent feeding experiments focused on seed traits after gut passage support the idea that fishes are major seed dispersers in floodplain and riparian forests. Overfishing, damming, deforestation and logging potentially diminish ichthyochory and require immediate attention to ameliorate their effects. Much exciting work remains in terms of fish and plant adaptations to ichthyochory, dispersal regimes involving fishes in different ecosystems, and increased use of nondestructive methods such as stomach lavage, stable isotopes, genetic analyses and radio transmitters to determine fish diets and movements.

Identification of metapopulation dynamics among Northern Goshawks of the Alexander Archipelago, Alaska, and Coastal British Columbia

USGS Publications Warehouse

Sonsthagen, Sarah A.; McClaren, Erica L.; Doyle, Frank I.; Titus, K.; Sage, George K.; Wilson, Robert E.; Gust, Judy R.; Talbot, Sandra L.

2012-01-01

Northern Goshawks occupying the Alexander Archipelago, Alaska, and coastal British Columbia nest primarily in old-growth and mature forest, which results in spatial heterogeneity in the distribution of individuals across the landscape. We used microsatellite and mitochondrial data to infer genetic structure, gene flow, and fluctuations in population demography through evolutionary time. Patterns in the genetic signatures were used to assess predictions associated with the three population models: panmixia, metapopulation, and isolated populations. Population genetic structure was observed along with asymmetry in gene flow estimates that changed directionality at different temporal scales, consistent with metapopulation model predictions. Therefore, Northern Goshawk assemblages located in the Alexander Archipelago and coastal British Columbia interact through a metapopulation framework, though they may not fit the classic model of a metapopulation. Long-term population sources (coastal mainland British Columbia) and sinks (Revillagigedo and Vancouver islands) were identified. However, there was no trend through evolutionary time in the directionality of dispersal among the remaining assemblages, suggestive of a rescue-effect dynamic. Admiralty, Douglas, and Chichagof island complex appears to be an evolutionarily recent source population in the Alexander Archipelago. In addition, Kupreanof island complex and Kispiox Forest District populations have high dispersal rates to populations in close geographic proximity and potentially serve as local source populations. Metapopulation dynamics occurring in the Alexander Archipelago and coastal British Columbia by Northern Goshawks highlight the importance of both occupied and unoccupied habitats to long-term population persistence of goshawks in this region.

Estimating near-road pollutant dispersion: a model inter-comparison

EPA Science Inventory

A model inter-comparison study to assess the abilities of steady-state Gaussian dispersion models to capture near-road pollutant dispersion has been carried out with four models (AERMOD, run with both the area-source and volume-source options to represent roadways, CALINE, versio...

Insights Gained from Forensic Analysis with MELCOR of the Fukushima-Daiichi Accidents.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Andrews, Nathan C.; Gauntt, Randall O.

Since the accidents at Fukushima-Daiichi, Sandia National Laboratories has been modeling these accident scenarios using the severe accident analysis code, MELCOR. MELCOR is a widely used computer code developed at Sandia National Laboratories since ~1982 for the U.S. Nuclear Regulatory Commission. Insights from the modeling of these accidents is being used to better inform future code development and potentially improved accident management. To date, our necessity to better capture in-vessel thermal-hydraulic and ex-vessel melt coolability and concrete interactions has led to the implementation of new models. The most recent analyses, presented in this paper, have been in support of themore » of the Organization for Economic Cooperation and Development Nuclear Energy Agency’s (OECD/NEA) Benchmark Study of the Accident at the Fukushima Daiichi Nuclear Power Station (BSAF) Project. The goal of this project is to accurately capture the source term from all three releases and then model the atmospheric dispersion. In order to do this, a forensic approach is being used in which available plant data and release timings is being used to inform the modeled MELCOR accident scenario. For example, containment failures, core slumping events and lower head failure timings are all enforced parameters in these analyses. This approach is fundamentally different from a blind code assessment analysis often used in standard problem exercises. The timings of these events are informed by representative spikes or decreases in plant data. The combination of improvements to the MELCOR source code resulting from analysis previous accident analysis and this forensic approach has allowed Sandia to generate representative and plausible source terms for all three accidents at Fukushima Daiichi out to three weeks after the accident to capture both early and late releases. In particular, using the source terms developed by MELCOR, the MACCS software code, which models atmospheric dispersion and deposition, we are able to reasonably capture the deposition of radionuclides to the northwest of the reactor site.« less

The direct reaction field hamiltonian: Analysis of the dispersion term and application to the water dimer

NASA Astrophysics Data System (ADS)

Thole, B. T.; Van Duijnen, P. Th.

1982-10-01

The induction and dispersion terms obtained from quantum-mechanical calculations with a direct reaction field hamiltonian are compared to second order perturbation theory expressions. The dispersion term is shown to give an upper bound which is a generalization of Alexander's upper bound. The model is illustrated by a calculation on the interactions in the water dimer. The long range Coulomb, induction and dispersion interactions are reasonably reproduced.

Circulation and microplastic dispersion in the Chiemsee (Germany) investigated with numerical modeling.

NASA Astrophysics Data System (ADS)

Marcello Falcieri, Francesco; Laforsch, Christian; Piehl, Sarah; Ricchi, Antonio; Atwood, Elizabeth C.; Carniel, Sandro; Sclavo, Mauro

2017-04-01

The Chiemsee (measuring about 80 km2 and a maximum depth of 73 m) is a NATURA 2000 site and one of the major German lakes and plays a significant environmental role for the region. Moreover it is an important touristic destination, making its beaches and water quality highly valuable from a socio-economical viewpoint. As for most inland European aquatic environments, the Chiemsee was recently found to be contaminated by microplastic (i.e. plastic fragments smaller than 0.5 mm). Two main microplastics sources were identified in the Chiemsee: riverine inputs, and degradation of litter from touristic beaches. Hence, it is of interest to study lake circulation and the resulting microplastic dispersion from these sources in order to support activities to achieve a good environmental status. Here we present the first attempt to characterize the hydrodynamic processes of the Chiemsee with a high resolution 3D implementation of the Regional Ocean Modeling System (ROMS). The simulations were forced with observed riverine inputs and modeled atmospherical fields computed with a local implementation of the Weather Research and Forecasting (WRF) model. Modeling results provide a first insight into the Chiemsee circulation system and contribute to understanding the dispersion pathways of microplastic particles from different sources. Furthermore, results can be used to highlight coastlines with higher risk of microplastic accumulation, identified using a set of Lagrangian simulations. The work was partially supported by the CNR Short Term Mobility grant.

Comparison of chlorine and ammonia concentration field trial data with calculated results from a Gaussian atmospheric transport and dispersion model.

PubMed

Bauer, Timothy J

2013-06-15

The Jack Rabbit Test Program was sponsored in April and May 2010 by the Department of Homeland Security Transportation Security Administration to generate source data for large releases of chlorine and ammonia from transport tanks. In addition to a variety of data types measured at the release location, concentration versus time data was measured using sensors at distances up to 500 m from the tank. Release data were used to create accurate representations of the vapor flux versus time for the ten releases. This study was conducted to determine the importance of source terms and meteorological conditions in predicting downwind concentrations and the accuracy that can be obtained in those predictions. Each source representation was entered into an atmospheric transport and dispersion model using simplifying assumptions regarding the source characterization and meteorological conditions, and statistics for cloud duration and concentration at the sensor locations were calculated. A detailed characterization for one of the chlorine releases predicted 37% of concentration values within a factor of two, but cannot be considered representative of all the trials. Predictions of toxic effects at 200 m are relevant to incidents involving 1-ton chlorine tanks commonly used in parts of the United States and internationally. Published by Elsevier B.V.

Regional-scale input of dispersed and discrete volcanic ash to the Izu-Bonin and Mariana subduction zones

NASA Astrophysics Data System (ADS)

Scudder, Rachel P.; Murray, Richard W.; Schindlbeck, Julie C.; Kutterolf, Steffen; Hauff, Folkmar; McKinley, Claire C.

2014-11-01

We have geochemically and statistically characterized bulk marine sediment and ash layers at Ocean Drilling Program Site 1149 (Izu-Bonin Arc) and Deep Sea Drilling Project Site 52 (Mariana Arc), and have quantified that multiple dispersed ash sources collectively comprise ˜30-35% of the hemipelagic sediment mass entering the Izu-Bonin-Mariana subduction system. Multivariate statistical analyses indicate that the bulk sediment at Site 1149 is a mixture of Chinese Loess, a second compositionally distinct eolian source, a dispersed mafic ash, and a dispersed felsic ash. We interpret the source of these ashes as, respectively, being basalt from the Izu-Bonin Front Arc (IBFA) and rhyolite from the Honshu Arc. Sr-, Nd-, and Pb isotopic analyses of the bulk sediment are consistent with the chemical/statistical-based interpretations. Comparison of the mass accumulation rate of the dispersed ash component to discrete ash layer parameters (thickness, sedimentation rate, and number of layers) suggests that eruption frequency, rather than eruption size, drives the dispersed ash record. At Site 52, the geochemistry and statistical modeling indicates that Chinese Loess, IBFA, dispersed BNN (boninite from Izu-Bonin), and a dispersed felsic ash of unknown origin are the sources. At Site 1149, the ash layers and the dispersed ash are compositionally coupled, whereas at Site 52 they are decoupled in that there are no boninite layers, yet boninite is dispersed within the sediment. Changes in the volcanic and eolian inputs through time indicate strong arc-related and climate-related controls.

Radio-frequency low-coherence interferometry.

PubMed

Fernández-Pousa, Carlos R; Mora, José; Maestre, Haroldo; Corral, Pablo

2014-06-15

A method for retrieving low-coherence interferograms, based on the use of a microwave photonics filter, is proposed and demonstrated. The method is equivalent to the double-interferometer technique, with the scanning interferometer replaced by an analog fiber-optics link and the visibility recorded as the amplitude of its radio-frequency (RF) response. As a low-coherence interferometry system, it shows a decrease of resolution induced by the fiber's third-order dispersion (β3). As a displacement sensor, it provides highly linear and slope-scalable readouts of the interferometer's optical path difference in terms of RF, even in the presence of third-order dispersion. In a proof-of-concept experiment, we demonstrate 20-μm displacement readouts using C-band EDFA sources and standard single-mode fiber.

Dispersion of a Passive Scalar Within and Above an Urban Street Network

NASA Astrophysics Data System (ADS)

Goulart, E. V.; Coceal, O.; Belcher, S. E.

2018-03-01

The transport of a passive scalar from a continuous point-source release in an urban street network is studied using direct numerical simulation (DNS). Dispersion through the network is characterized by evaluating horizontal fluxes of scalar within and above the urban canopy and vertical exchange fluxes through the canopy top. The relative magnitude and balance of these fluxes are used to distinguish three different regions relative to the source location: a near-field region, a transition region and a far-field region. The partitioning of each of these fluxes into mean and turbulent parts is computed. It is shown that within the canopy the horizontal turbulent flux in the street network is small, whereas above the canopy it comprises a significant fraction of the total flux. Vertical fluxes through the canopy top are predominantly turbulent. The mean and turbulent fluxes are respectively parametrized in terms of an advection velocity and a detrainment velocity and the parametrization incorporated into a simple box-network model. The model treats the coupled dispersion problem within and above the street network in a unified way and predictions of mean concentrations compare well with the DNS data. This demonstrates the usefulness of the box-network approach for process studies and interpretation of results from more detailed numerical simulations.

Teaching and communicating dispersion in hydrogeology, with emphasis on the applicability of the Fickian model

NASA Astrophysics Data System (ADS)

Kitanidis, P. K.

2017-08-01

The process of dispersion in porous media is the effect of combined variability in fluid velocity and concentration at scales smaller than the ones resolved that contributes to spreading and mixing. It is usually introduced in textbooks and taught in classes through the Fick-Scheidegger parameterization, which is introduced as a scientific law of universal validity. This parameterization is based on observations in bench-scale laboratory experiments using homogeneous media. Fickian means that dispersive flux is proportional to the gradient of the resolved concentration while the Scheidegger parameterization is a particular way to compute the dispersion coefficients. The unresolved scales are thus associated with the pore-grain geometry that is ignored when the composite pore-grain medium is replaced by a homogeneous continuum. However, the challenge faced in practice is how to account for dispersion in numerical models that discretize the domain into blocks, often cubic meters in size, that contain multiple geologic facies. Although the Fick-Scheidegger parameterization is by far the one most commonly used, its validity has been questioned. This work presents a method of teaching dispersion that emphasizes the physical basis of dispersion and highlights the conditions under which a Fickian dispersion model is justified. In particular, we show that Fickian dispersion has a solid physical basis provided that an equilibrium condition is met. The issue of the Scheidegger parameterization is more complex but it is shown that the approximation that the dispersion coefficients should scale linearly with the mean velocity is often reasonable, at least as a practical approximation, but may not necessarily be always appropriate. Generally in Hydrogeology, the Scheidegger feature of constant dispersivity is considered as a physical law and inseparable from the Fickian model, but both perceptions are wrong. We also explain why Fickian dispersion fails under certain conditions, such as dispersion inside and directly upstream of a contaminant source. Other issues discussed are the relevance of column tests and confusion regarding the meaning of terms dispersion and Fickian.

Development, Evaluation, and Application of a Primary Aerosol Model.

PubMed

Wang, I T; Chico, T; Huang, Y H; Farber, R J

1999-09-01

The Segmented-Plume Primary Aerosol Model (SPPAM) has been developed over the past several years. The earlier model development goals were simply to generalize the widely used Industrial Source Complex Short-Term (ISCST) model to simulate plume transport and dispersion under light wind conditions and to handle a large number of roadway or line sources. The goals have been expanded to include development of improved algorithm for effective plume transport velocity, more accurate and efficient line and area source dispersion algorithms, and recently, a more realistic and computationally efficient algorithm for plume depletion due to particle dry deposition. A performance evaluation of the SPPAM has been carried out using the 1983 PNL dual tracer experimental data. The results show the model predictions to be in good agreement with observations in both plume advection-dispersion and particulate matter (PM) depletion by dry deposition. For PM 2.5 impact analysis, the SPPAM has been applied to the Rubidoux area of California. Emission sources included in the modeling analysis are: paved road dust, diesel vehicular exhaust, gasoline vehicular exhaust, and tire wear particles from a large number of roadways in Rubidoux and surrounding areas. For the selected modeling periods, the predicted primary PM 2.5 to primary PM10 concentration ratios for the Rubidoux sampling station are in the range of 0.39-0.46. The organic fractions of the primary PM 2.5 impacts are estimated to be at least 34-41%. Detailed modeling results indicate that the relatively high organic fractions are primarily due to the proximity of heavily traveled roadways north of the sampling station. The predictions are influenced by a number of factors; principal among them are the receptor locations relative to major roadways, the volume and composition of traffic on these roadways, and the prevailing meteorological conditions.

The modelling of odour dispersion as a support tool for the improvements of high odours impact plants.

PubMed

Luciano, Antonella; Torretta, Vincenzo; Mancini, Giuseppe; Eleuteri, Andrea; Raboni, Massimo; Viotti, Paolo

2017-03-01

Two scenarios in terms of odour impact assessment were studied during the phase of upgrading of an existing waste treatment plant: CALPUFF was used for the simulation of odour dispersion. Olfactometric measures, carried out over different periods and different positions in the plant, were used for model calibration. Results from simulations were reported in terms of statistics of odour concentrations and isopleths maps of the 98th percentile of the hourly peak concentrations, as requested from the European legislation and standards. The excess perception thresholds and emissions were utilized to address the plant upgrade options. The hourly evaluation of odours was performed to determine the most impacting period of the day. An inverse application of the numerical simulation starting from defining the odour threshold at the receptor was made to allow the definition of the required abatement efficiency at the odours source location. Results from the proposed approach confirmed the likelihood to adopt odour dispersion modelling, not only in the authorization phase, but also as a tool for driving technical and managing actions in plant upgrade so to reduce impacts and improve the public acceptance. The upgrade actions in order to achieve the expected efficiency are reported as well.

Tigers in the Terai: Strong evidence for meta-population dynamics contributing to tiger recovery and conservation in the Terai Arc Landscape.

PubMed

Thapa, Kanchan; Wikramanayake, Eric; Malla, Sabita; Acharya, Krishna Prasad; Lamichhane, Babu Ram; Subedi, Naresh; Pokharel, Chiranjivi Prasad; Thapa, Gokarna Jung; Dhakal, Maheshwar; Bista, Ashish; Borah, Jimmy; Gupta, Mudit; Maurya, Kamlesh K; Gurung, Ghana Shyam; Jnawali, Shant Raj; Pradhan, Narendra Man Babu; Bhata, Shiv Raj; Koirala, Saroj; Ghose, Dipankar; Vattakaven, Joseph

2017-01-01

The source populations of tigers are mostly confined to protected areas, which are now becoming isolated. A landscape scale conservation strategy should strive to facilitate dispersal and survival of dispersing tigers by managing habitat corridors that enable tigers to traverse the matrix with minimal conflict. We present evidence for tiger dispersal along transboundary protected areas complexes in the Terai Arc Landscape, a priority tiger landscape in Nepal and India, by comparing camera trap data, and through population models applied to the long term camera trap data sets. The former showed that 11 individual tigers used the corridors that connected the transboundary protected areas. The estimated population growth rates using the minimum observed population size in two protected areas in Nepal, Bardia National Park and Suklaphanta National Park showed that the increases were higher than expected from growth rates due to in situ reproduction alone. These lines of evidence suggests that tigers are recolonizing Nepal's protected areas from India, after a period of population decline, and that the tiger populations in the transboundary protected areas complexes may be maintained as meta-population. Our results demonstrate the importance of adopting a landscape-scale approach to tiger conservation, especially to improve population recovery and long term population persistence.

Tigers in the Terai: Strong evidence for meta-population dynamics contributing to tiger recovery and conservation in the Terai Arc Landscape

PubMed Central

Wikramanayake, Eric; Malla, Sabita; Acharya, Krishna Prasad; Lamichhane, Babu Ram; Subedi, Naresh; Pokharel, Chiranjivi Prasad; Thapa, Gokarna Jung; Dhakal, Maheshwar; Bista, Ashish; Borah, Jimmy; Gupta, Mudit; Maurya, Kamlesh K.; Gurung, Ghana Shyam; Jnawali, Shant Raj; Pradhan, Narendra Man Babu; Bhata, Shiv Raj; Koirala, Saroj; Ghose, Dipankar; Vattakaven, Joseph

2017-01-01

The source populations of tigers are mostly confined to protected areas, which are now becoming isolated. A landscape scale conservation strategy should strive to facilitate dispersal and survival of dispersing tigers by managing habitat corridors that enable tigers to traverse the matrix with minimal conflict. We present evidence for tiger dispersal along transboundary protected areas complexes in the Terai Arc Landscape, a priority tiger landscape in Nepal and India, by comparing camera trap data, and through population models applied to the long term camera trap data sets. The former showed that 11 individual tigers used the corridors that connected the transboundary protected areas. The estimated population growth rates using the minimum observed population size in two protected areas in Nepal, Bardia National Park and Suklaphanta National Park showed that the increases were higher than expected from growth rates due to in situ reproduction alone. These lines of evidence suggests that tigers are recolonizing Nepal’s protected areas from India, after a period of population decline, and that the tiger populations in the transboundary protected areas complexes may be maintained as meta-population. Our results demonstrate the importance of adopting a landscape-scale approach to tiger conservation, especially to improve population recovery and long term population persistence. PMID:28591175

An implicit dispersive transport algorithm for the US Geological Survey MOC3D solute-transport model

USGS Publications Warehouse

Kipp, K.L.; Konikow, Leonard F.; Hornberger, G.Z.

1998-01-01

This report documents an extension to the U.S. Geological Survey MOC3D transport model that incorporates an implicit-in-time difference approximation for the dispersive transport equation, including source/sink terms. The original MOC3D transport model (Version 1) uses the method of characteristics to solve the transport equation on the basis of the velocity field. The original MOC3D solution algorithm incorporates particle tracking to represent advective processes and an explicit finite-difference formulation to calculate dispersive fluxes. The new implicit procedure eliminates several stability criteria required for the previous explicit formulation. This allows much larger transport time increments to be used in dispersion-dominated problems. The decoupling of advective and dispersive transport in MOC3D, however, is unchanged. With the implicit extension, the MOC3D model is upgraded to Version 2. A description of the numerical method of the implicit dispersion calculation, the data-input requirements and output options, and the results of simulator testing and evaluation are presented. Version 2 of MOC3D was evaluated for the same set of problems used for verification of Version 1. These test results indicate that the implicit calculation of Version 2 matches the accuracy of Version 1, yet is more efficient than the explicit calculation for transport problems that are characterized by a grid Peclet number less than about 1.0.

Appropriateness of selecting different averaging times for modelling chronic and acute exposure to environmental odours

NASA Astrophysics Data System (ADS)

Drew, G. H.; Smith, R.; Gerard, V.; Burge, C.; Lowe, M.; Kinnersley, R.; Sneath, R.; Longhurst, P. J.

Odour emissions are episodic, characterised by periods of high emission rates, interspersed with periods of low emissions. It is frequently the short term, high concentration peaks that result in annoyance in the surrounding population. Dispersion modelling is accepted as a useful tool for odour impact assessment, and two approaches can be adopted. The first approach of modelling the hourly average concentration can underestimate total odour concentration peaks, resulting in annoyance and complaints. The second modelling approach involves the use of short averaging times. This study assesses the appropriateness of using different averaging times to model the dispersion of odour from a landfill site. We also examine perception of odour in the community in conjunction with the modelled odour dispersal, by using community monitors to record incidents of odour. The results show that with the shorter averaging times, the modelled pattern of dispersal reflects the pattern of observed odour incidents recorded in the community monitoring database, with the modelled odour dispersing further in a north easterly direction. Therefore, the current regulatory method of dispersion modelling, using hourly averaging times, is less successful at capturing peak concentrations, and does not capture the pattern of odour emission as indicated by the community monitoring database. The use of short averaging times is therefore of greater value in predicting the likely nuisance impact of an odour source and in framing appropriate regulatory controls.

Bayesian inverse modeling and source location of an unintended 131I release in Europe in the fall of 2011

NASA Astrophysics Data System (ADS)

Tichý, Ondřej; Šmídl, Václav; Hofman, Radek; Šindelářová, Kateřina; Hýža, Miroslav; Stohl, Andreas

2017-10-01

In the fall of 2011, iodine-131 (131I) was detected at several radionuclide monitoring stations in central Europe. After investigation, the International Atomic Energy Agency (IAEA) was informed by Hungarian authorities that 131I was released from the Institute of Isotopes Ltd. in Budapest, Hungary. It was reported that a total activity of 342 GBq of 131I was emitted between 8 September and 16 November 2011. In this study, we use the ambient concentration measurements of 131I to determine the location of the release as well as its magnitude and temporal variation. As the location of the release and an estimate of the source strength became eventually known, this accident represents a realistic test case for inversion models. For our source reconstruction, we use no prior knowledge. Instead, we estimate the source location and emission variation using only the available 131I measurements. Subsequently, we use the partial information about the source term available from the Hungarian authorities for validation of our results. For the source determination, we first perform backward runs of atmospheric transport models and obtain source-receptor sensitivity (SRS) matrices for each grid cell of our study domain. We use two dispersion models, FLEXPART and Hysplit, driven with meteorological analysis data from the global forecast system (GFS) and from European Centre for Medium-range Weather Forecasts (ECMWF) weather forecast models. Second, we use a recently developed inverse method, least-squares with adaptive prior covariance (LS-APC), to determine the 131I emissions and their temporal variation from the measurements and computed SRS matrices. For each grid cell of our simulation domain, we evaluate the probability that the release was generated in that cell using Bayesian model selection. The model selection procedure also provides information about the most suitable dispersion model for the source term reconstruction. Third, we select the most probable location of the release with its associated source term and perform a forward model simulation to study the consequences of the iodine release. Results of these procedures are compared with the known release location and reported information about its time variation. We find that our algorithm could successfully locate the actual release site. The estimated release period is also in agreement with the values reported by IAEA and the reported total released activity of 342 GBq is within the 99 % confidence interval of the posterior distribution of our most likely model.

Bayesian source term estimation of atmospheric releases in urban areas using LES approach.

PubMed

Xue, Fei; Kikumoto, Hideki; Li, Xiaofeng; Ooka, Ryozo

2018-05-05

The estimation of source information from limited measurements of a sensor network is a challenging inverse problem, which can be viewed as an assimilation process of the observed concentration data and the predicted concentration data. When dealing with releases in built-up areas, the predicted data are generally obtained by the Reynolds-averaged Navier-Stokes (RANS) equations, which yields building-resolving results; however, RANS-based models are outperformed by large-eddy simulation (LES) in the predictions of both airflow and dispersion. Therefore, it is important to explore the possibility of improving the estimation of the source parameters by using the LES approach. In this paper, a novel source term estimation method is proposed based on LES approach using Bayesian inference. The source-receptor relationship is obtained by solving the adjoint equations constructed using the time-averaged flow field simulated by the LES approach based on the gradient diffusion hypothesis. A wind tunnel experiment with a constant point source downwind of a single building model is used to evaluate the performance of the proposed method, which is compared with that of the existing method using a RANS model. The results show that the proposed method reduces the errors of source location and releasing strength by 77% and 28%, respectively. Copyright © 2018 Elsevier B.V. All rights reserved.

RLINE: A Line Source Dispersion Model for Near-Surface Releases

EPA Science Inventory

This paper describes the formulation and evaluation of RLINE, a Research LINE source model for near surface releases. The model is designed to simulate mobile source pollutant dispersion to support the assessment of human exposures in near-roadway environments where a significant...

Hydrocarbon-Degrading Bacteria Exhibit a Species-Specific Response to Dispersed Oil while Moderating Ecotoxicity

PubMed Central

Overholt, Will A.; Marks, Kala P.; Romero, Isabel C.; Hollander, David J.; Snell, Terry W.

2015-01-01

The Deepwater Horizon blowout in April 2010 represented the largest accidental marine oil spill and the largest release of chemical dispersants into the environment to date. While dispersant application may provide numerous benefits to oil spill response efforts, the impacts of dispersants and potential synergistic effects with crude oil on individual hydrocarbon-degrading bacteria are poorly understood. In this study, two environmentally relevant species of hydrocarbon-degrading bacteria were utilized to quantify the response to Macondo crude oil and Corexit 9500A-dispersed oil in terms of bacterial growth and oil degradation potential. In addition, specific hydrocarbon compounds were quantified in the dissolved phase of the medium and linked to ecotoxicity using a U.S. Environmental Protection Agency (EPA)-approved rotifer assay. Bacterial treatment significantly and drastically reduced the toxicity associated with dispersed oil (increasing the 50% lethal concentration [LC50] by 215%). The growth and crude oil degradation potential of Acinetobacter were inhibited by Corexit by 34% and 40%, respectively; conversely, Corexit significantly enhanced the growth of Alcanivorax by 10% relative to that in undispersed oil. Furthermore, both bacterial strains were shown to grow with Corexit as the sole carbon and energy source. Hydrocarbon-degrading bacterial species demonstrate a unique response to dispersed oil compared to their response to crude oil, with potentially opposing effects on toxicity. While some species have the potential to enhance the toxicity of crude oil by producing biosurfactants, the same bacteria may reduce the toxicity associated with dispersed oil through degradation or sequestration. PMID:26546426

Evaluation of radiological dispersion/consequence codes supporting DOE nuclear facility SARs

DOE Office of Scientific and Technical Information (OSTI.GOV)

O`Kula, K.R.; Paik, I.K.; Chung, D.Y.

1996-12-31

Since the early 1990s, the authorization basis documentation of many U.S. Department of Energy (DOE) nuclear facilities has been upgraded to comply with DOE orders and standards. In this process, many safety analyses have been revised. Unfortunately, there has been nonuniform application of software, and the most appropriate computer and engineering methodologies often are not applied. A DOE Accident Phenomenology and Consequence (APAC) Methodology Evaluation Program was originated at the request of DOE Defense Programs to evaluate the safety analysis methodologies used in nuclear facility authorization basis documentation and to define future cost-effective support and development initiatives. Six areas, includingmore » source term development (fire, spills, and explosion analysis), in-facility transport, and dispersion/ consequence analysis (chemical and radiological) are contained in the APAC program. The evaluation process, codes considered, key results, and recommendations for future model and software development of the Radiological Dispersion/Consequence Working Group are summarized in this paper.« less

Source, dispersion and combustion modelling of an accidental release of hydrogen in an urban environment.

PubMed

Venetsanos, A G; Huld, T; Adams, P; Bartzis, J G

2003-12-12

Hydrogen is likely to be the most important future energy carrier, for many stationary and mobile applications, with the potential to make significant reductions in greenhouse gas emissions especially if renewable primary energy sources are used to produce the hydrogen. A safe transition to the use of hydrogen by members of the general public requires that the safety issues associated with hydrogen applications have to be investigated and fully understood. In order to assess the risks associated with hydrogen applications, its behaviour in realistic accident scenarios has to be predicted, allowing mitigating measures to be developed where necessary. A key factor in this process is predicting the release, dispersion and combustion of hydrogen in appropriate scenarios. This paper illustrates an application of CFD methods to the simulation of an actual hydrogen explosion. The explosion occurred on 3 March 1983 in a built up area of central Stockholm, Sweden, after the accidental release of approximately 13.5 kg of hydrogen from a rack of 18 interconnected 50 l industrial pressure vessels (200 bar working pressure) being transported by a delivery truck. Modelling of the source term, dispersion and combustion were undertaken separately using three different numerical tools, due to the differences in physics and scales between the different phenomena. Results from the dispersion calculations together with the official accident report were used to identify a possible ignition source and estimate the time at which ignition could have occurred. Ignition was estimated to occur 10s after the start of the release, coinciding with the time at which the maximum flammable hydrogen mass and cloud volume were found to occur (4.5 kg and 600 m(3), respectively). The subsequent simulation of the combustion adopts initial conditions for mean flow and turbulence from the dispersion simulations, and calculates the development of a fireball. This provides physical values, e.g. maximum overpressure and far-field overpressure that may be used as a comparison with the known accident details to give an indication of the validity of the models. The simulation results are consistent with both the reported near-field damage to buildings and persons and with the far-field damage to windows. The work was undertaken as part of the European Integrated Hydrogen Project-Phase 2 (EIHP2) with partial funding from the European Commission via the Fifth Framework Programme.

Does ascorbic acid supplementation affect iron bioavailability in rats fed micronized dispersible ferric pyrophosphate fortified fruit juice?

PubMed

Haro-Vicente, Juan Francisco; Pérez-Conesa, Darío; Rincón, Francisco; Ros, Gaspar; Martínez-Graciá, Carmen; Vidal, Maria Luisa

2008-12-01

Food iron (Fe) fortification is an adequate approach for preventing Fe-deficiency anemia. Poorly water-soluble Fe compounds have good sensory attributes but low bioavailability. The reduction of the particle size of Fe fortificants and the addition of ascorbic acid might increase the bioavailability of low-soluble compounds. The present work aims to compare the Fe absorption and bioavailability of micronized dispersible ferric pyrophosphate (MDFP) (poorly soluble) to ferrous sufate (FS) (highly soluble) added to a fruit juice in presence or absence of ascorbic acid (AA) by using the hemoglobin repletion assay in rats. After a hemoglobin depletion period, four fruit juices comprised of (1) FS, (2) MDFP, (3) FS + AA, (4) MDFP + AA were produced and administered to a different group of rats (n = 18) over 21 days. During the repletion period, Fe balance, hemoglobin regeneration efficiency (HRE), relative bioavailability (RBV) and Fe tissue content were determined in the short, medium and long term. Fe absorption and bioavailability showed no significant differences between fortifying the fruit juice with FS or MDFP. The addition of AA to the juice enhanced Fe absorption during the long-term balance study within the same Fe source. HRE and Fe utilization increased after AA addition in both FS and MDFP groups in every period. Fe absorption and bioavailability from MDFP were comparable to FS added to a fruit juice in rats. Further, the addition of AA enhanced Fe absorption in the long term, as well as Fe bioavailability throughout the repletion period regardless of the Fe source employed.

Marine litter from beach-based sources: Case study of an Eastern Mediterranean coastal town.

PubMed

Portman, Michelle E; Brennan, Ruth E

2017-11-01

Marine litter has been a serious and growing problem for some decades now. Yet, there is still much speculation among researchers, policy makers and planners about how to tackle marine litter from land-based sources. This paper provides insights into approaches for managing marine litter by reporting and analyzing survey results of litter dispersal and makeup from three areas along an Arab-Israeli coastal town in view of other recent studies conducted around the Mediterranean Sea. Based on our results and analysis, we posit that bathing beach activities should be a high priority for waste managers as a point of intervention and beach-goers must be encouraged to take a more active role in keeping beaches clean. Further, plastic fragments on the beach should be targeted as a first priority for prevention (and cleanup) of marine litter with plastic bottle caps being a high priority to be targeted among plastics. More survey research is needed on non-plastic litter composition for which amounts and geographic dispersal in the region vary greatly from place to place along Mediterranean shores. In general, findings of this study lead us to recommend exploring persuasive beach trash can design coupled with greater enforcement for short term waste management intervention while considering the local socio-economic and institutional context further for long-term efforts. Copyright © 2017 Elsevier Ltd. All rights reserved.

Health risk assessments for alumina refineries.

PubMed

Donoghue, A Michael; Coffey, Patrick S

2014-05-01

To describe contemporary air dispersion modeling and health risk assessment methodologies applied to alumina refineries and to summarize recent results. Air dispersion models using emission source and meteorological data have been used to assess ground-level concentrations (GLCs) of refinery emissions. Short-term (1-hour and 24-hour average) GLCs and annual average GLCs have been used to assess acute health, chronic health, and incremental carcinogenic risks. The acute hazard index can exceed 1 close to refineries, but it is typically less than 1 at neighboring residential locations. The chronic hazard index is typically substantially less than 1. The incremental carcinogenic risk is typically less than 10(-6). The risks of acute health effects are adequately controlled, and the risks of chronic health effects and incremental carcinogenic risks are negligible around referenced alumina refineries.

On the role of mean flows in Doppler shifted frequencies

NASA Astrophysics Data System (ADS)

Gerkema, Theo; Maas, Leo R. M.; van Haren, Hans

2013-04-01

In the oceanographic literature, the term 'Doppler shift' often features in the context of mean flows and (internal) waves. Closer inspection reveals that the term is in fact used for two different things, which should be carefully distinguished, for their conflation results in incorrect interpretations. One refers to the difference in frequencies measured by two observers, one at a fixed position and one moving with the mean flow. The other definition is the one used in physics, where the frequency measured by an observer is compared to that of the source. In the latter sense, Doppler shifts occur only if the source and observer move with respect to each other; a steady mean flow cannot create a Doppler shift. We rehash the classical theory to straighten out some misconceptions and discuss how wave dispersion affects the classical relations and their application, for example on near-inertial internal waves.

Turbulent mass inhomogeneities induced by a point-source

NASA Astrophysics Data System (ADS)

Thalabard, Simon

2018-03-01

We describe how turbulence distributes tracers away from a localized source of injection, and analyze how the spatial inhomogeneities of the concentration field depend on the amount of randomness in the injection mechanism. For that purpose, we contrast the mass correlations induced by purely random injections with those induced by continuous injections in the environment. Using the Kraichnan model of turbulent advection, whereby the underlying velocity field is assumed to be shortly correlated in time, we explicitly identify scaling regions for the statistics of the mass contained within a shell of radius r and located at a distance ρ away from the source. The two key parameters are found to be (i) the ratio s 2 between the absolute and the relative timescales of dispersion and (ii) the ratio Λ between the size of the cloud and its distance away from the source. When the injection is random, only the former is relevant, as previously shown by Celani et al (2007 J. Fluid Mech. 583 189–98) in the case of an incompressible fluid. It is argued that the space partition in terms of s 2 and Λ is a robust feature of the injection mechanism itself, which should remain relevant beyond the Kraichnan model. This is for instance the case in a generalized version of the model, where the absolute dispersion is prescribed to be ballistic rather than diffusive.

Source-receptor probability of atmospheric long-distance dispersal of viruses to Israel from the eastern Mediterranean area.

PubMed

Klausner, Z; Klement, E; Fattal, E

2018-02-01

Viruses that affect the health of humans and farm animals can spread over long distances via atmospheric mechanisms. The phenomenon of atmospheric long-distance dispersal (LDD) is associated with severe consequences because it may introduce pathogens into new areas. The introduction of new pathogens to Israel was attributed to LDD events numerous times. This provided the motivation for this study which is aimed to identify all the locations in the eastern Mediterranean that may serve as sources for pathogen incursion into Israel via LDD. This aim was achieved by calculating source-receptor relationship probability maps. These maps describe the probability that an infected vector or viral aerosol, once airborne, will have an atmospheric route that can transport it to a distant location. The resultant probability maps demonstrate a seasonal tendency in the probability of specific areas to serve as sources for pathogen LDD into Israel. Specifically, Cyprus' season is the summer; southern Turkey and the Greek islands of Crete, Karpathos and Rhodes are associated with spring and summer; lower Egypt and Jordan may serve as sources all year round, except the summer months. The method used in this study can easily be implemented to any other geographic region. The importance of this study is the ability to provide a climatologically valid and accurate risk assessment tool to support long-term decisions regarding preparatory actions for future outbreaks long before a specific outbreak occurs. © 2017 Blackwell Verlag GmbH.

Non-Gaussian limit fluctuations in active swimmer suspensions

NASA Astrophysics Data System (ADS)

Kurihara, Takashi; Aridome, Msato; Ayade, Heev; Zaid, Irwin; Mizuno, Daisuke

2017-03-01

We investigate the hydrodynamic fluctuations in suspensions of swimming microorganisms (Chlamydomonas) by observing the probe particles dispersed in the media. Short-term fluctuations of probe particles were superdiffusive and displayed heavily tailed non-Gaussian distributions. The analytical theory that explains the observed distribution was derived by summing the power-law-decaying hydrodynamic interactions from spatially distributed field sources (here, swimming microorganisms). The summing procedure, which we refer to as the physical limit operation, is applicable to a variety of physical fluctuations to which the classical central limiting theory does not apply. Extending the analytical formula to compare to experiments in active swimmer suspensions, we show that the non-Gaussian shape of the observed distribution obeys the analytic theory concomitantly with independently determined parameters such as the strength of force generations and the concentration of Chlamydomonas. Time evolution of the distributions collapsed to a single master curve, except for their extreme tails, for which our theory presents a qualitative explanation. Investigations thereof and the complete agreement with theoretical predictions revealed broad applicability of the formula to dispersions of active sources of fluctuations.

Identification and elucidation of anthropogenic source contribution in PM10 pollutant: Insight gain from dispersion and receptor models.

PubMed

Roy, Debananda; Singh, Gurdeep; Yadav, Pankaj

2016-10-01

Source apportionment study of PM 10 (Particulate Matter) in a critically polluted area of Jharia coalfield, India has been carried out using Dispersion model, Principle Component Analysis (PCA) and Chemical Mass Balance (CMB) techniques. Dispersion model Atmospheric Dispersion Model (AERMOD) was introduced to simplify the complexity of sources in Jharia coalfield. PCA and CMB analysis indicates that monitoring stations near the mining area were mainly affected by the emission from open coal mining and its associated activities such as coal transportation, loading and unloading of coal. Mine fire emission also contributed a considerable amount of particulate matters in monitoring stations. Locations in the city area were mostly affected by vehicular, Liquid Petroleum Gas (LPG) & Diesel Generator (DG) set emissions, residential, and commercial activities. The experimental data sampling and their analysis could aid understanding how dispersion based model technique along with receptor model based concept can be strategically used for quantitative analysis of Natural and Anthropogenic sources of PM 10 . Copyright © 2016. Published by Elsevier B.V.

Local infestation or long-distance migration? The seasonal recolonization of dairy farms by Stomoxys calcitrans (Diptera: Muscidae) in south central Ontario, Canada.

PubMed

Beresford, D V; Sutcliffe, J F

2009-04-01

Stable fly (Diptera: Muscidae) populations in south central Ontario, Canada, first occur on dairy farms in late spring, grow exponentially throughout the summer, and are frozen back each autumn. We examined the extent of overwinter persistence on 22 dairy farms in a 55- by 60-km region north of Lake Ontario that spans four climatic zones. Our overwintering sampling of larval habitat identified three farms located in the southern section of the study region as potential overwintering refugia. Using sticky trap catches to identify the timing of first spring appearance at each farm, we then tested two models of how local farm populations are reestablished annually: 1) stable flies disperse from local climatic refuges and colonize neighboring farms (the local source model); and 2) stable flies are carried into the study region by frontal weather systems (the distant source model). The timing of when stable flies first occurred at these farms supported a local source of dispersing colonists from a small proportion of local refuge farms. We discuss our results in terms of how yearly fluctuation in climate would affect refuge farm density in the region and how this, in turn, would shift the recolonization dynamic. Implications for controlling stable flies also are discussed.

A new modeling approach for assessing the contribution of industrial and traffic emissions to ambient NOx concentrations

NASA Astrophysics Data System (ADS)

Chen, Shimon; Yuval; Broday, David M.

2018-01-01

The Optimized Dispersion Model (ODM) is uniquely capable of incorporating emission estimates, ambient air quality monitoring data and meteorology to provide reliable high-resolution (in both time and space) air quality estimates using non-linear regression. However, it was so far not capable of describing the effects of emissions from elevated sources. We formulated an additional term to extend the ODM such that these sources can be accounted for, and implemented it in modeling the fine spatiotemporal patterns of ambient NOx concentrations over the coastal plain of Israel. The diurnal and seasonal variation in the contribution of industry to the ambient NOx is presented, as well as its spatial features. Although industrial stacks are responsible for 88% of the NOx emissions in the study area, their contribution to ambient NOx levels is generally about 2% with a maximal upper bound of 27%. Meteorology has a major role in this source allocation, with the highest impact of industry in the summer months, when the wind is blowing inland past the coastal stacks and vertical mixing is substantial. The new Optimized Dispersion Model (ODM) out-performs both Inverse-Distance-Weighing (IDW) interpolation and a previous ODM version in predicting ambient NOx concentrations. The performance of the new model is thoroughly assessed.

Seed source, seed traits, and frugivore habits: Implications for dispersal quality of two sympatric primates.

PubMed

Benítez-Malvido, Julieta; González-Di Pierro, Ana Ma; Lombera, Rafael; Guillén, Susana; Estrada, Alejandro

2014-06-01

• Premise of the study: Frugivore selection of fruits and treatment of seeds together with seed deposition site are crucial for the population dynamics of vertebrate-dispersed plants. However, frugivore species may influence dispersal quality differently even when feeding on the same fruit species and, while animals disperse some seeds, others simply fall beneath the parent plant.• Methods: In southern Mexico, we investigated to see if within-species seed traits (i.e., length, width, weight, and volume) and germination success differed according to seed source. For five tropical tree species we obtained ingested seeds from two sources, howler monkey (Alouatta pigra) and spider monkey (Ateles geoffroyi) feces; and noningested seeds from two sources, the ground and tree crowns (with predispersed seeds used as control).• Key results: A principal components' analysis showed that traits of seeds ingested by howler monkeys differed from other sources while seeds ingested by spider monkeys were similar to noningested seeds. Howlers consumed on average the larger seeds in Ampelocera hottlei, Brosimum lactescens, and Dialium guianense. Both primate species consumed the smaller seeds in Spondias mombin, while no seed trait differences among seed sources were found in Spondias radlkoferi. For all five tree species, germination rate was greatest for seeds ingested by howler monkeys.• Conclusions: For the studied plant species, seed ingestion by howler monkeys confers higher dispersal quality than ingestion by spider monkeys or nondispersal. Dispersal services of both primate species, however, are not redundant and may contribute to germination heterogeneity within plant populations in tropical forests. © 2014 Botanical Society of America, Inc.

OCT imaging with temporal dispersion induced intense and short coherence laser source

NASA Astrophysics Data System (ADS)

Manna, Suman K.; le Gall, Stephen; Li, Guoqiang

2016-10-01

Lower coherence length and higher intensity are two indispensable requirements on the light source for high resolution and large penetration depth OCT imaging. While tremendous interest is being paid on engineering various laser sources to enlarge their bandwidth and hence lowering the coherence length, here we demonstrate another approach by employing strong temporal dispersion onto the existing laser source. Cholesteric liquid crystal (CLC) cells with suitable dispersive slope at the edge of 1-D organic photonic band gap have been designed to provide maximum reduction in coherence volume while maintaining the intensity higher than 50%. As an example, the coherence length of a multimode He-Ne laser is reduced by more than 730 times.

Dispersal of remnant endangered trees in a fragmented and disturbed forest by frugivorous birds.

PubMed

Li, Ning; Bai, Bing; Li, Xin-Hai; An, Shu-Qing; Lu, Chang-Hu

2017-07-01

Most endangered plant species in a fragmented forest behave as a unique source population, with a high dependence on frugivorous birds for recruitment and persistence. In this study, we combined field data of dispersal behavior of birds and GIS information of patch attributes to estimate how frugivorous birds could affect the effective dispersal pattern of Chinese yew (Taxus chinensis) in a fragmented and disturbed forest. Nine bird species were observed to visit T. chinensis trees, with Urocissa erythrorhyncha, Zoothera dauma and Picus canus being the most common dispersers. After foraging, six disperser species exhibited different perching patterns. Three specialist species, P. canus, Turdus hortulorum, and Z. dauma stayed in the source patch, while three generalist species, U. erythrorhyncha, Hypsipetes mcclellandii, and H. castanonotus, could perch in bamboo patches and varied in movement ability due to body size. As a consequence of perching, dispersers significantly contributed to the seed bank, but indirectly affected seedling recruitment. Moreover, the recruitment of T. chinensis was also affected by patch attributes in a fragmented forest (distances to source patch, patch type, size). Our results highlighted the ability of unique source population regeneration of T. chinensis in a fragmented forest, with high dependence on both frugivorous birds and patch attributes, which should be considered in future planning for forest management and conservation.

Analysis and suppression of passive noise in surface microseismic data

NASA Astrophysics Data System (ADS)

Forghani-Arani, Farnoush

Surface microseismic surveys are gaining popularity in monitoring the hydraulic fracturing process. The effectiveness of these surveys, however, is strongly dependent on the signal-to-noise ratio of the acquired data. Cultural and industrial noise generated during hydraulic fracturing operations usually dominate the data, thereby decreasing the effectiveness of using these data in identifying and locating microseismic events. Hence, noise suppression is a critical step in surface microseismic monitoring. In this thesis, I focus on two important aspects in using surface-recorded microseismic seismic data: first, I take advantage of the unwanted surface noise to understand the characteristics of these noise and extract information about the propagation medium from the noise; second, I propose effective techniques to suppress the surface noise while preserving the waveforms that contain information about the source of microseisms. Automated event identification on passive seismic data using only a few receivers is challenging especially when the record lengths span over long durations of time. I introduce an automatic event identification algorithm that is designed specifically for detecting events in passive data acquired with a small number of receivers. I demonstrate that the conventional STA/LTA (Short-term Average/Long-term Average) algorithm is not sufficiently effective in event detection in the common case of low signal-to-noise ratio. With a cross-correlation based method as an extension of the STA/LTA algorithm, even low signal-to-noise events (that were not detectable with conventional STA/LTA) were revealed. Surface microseismic data contains surface-waves (generated primarily from hydraulic fracturing activities) and body-waves in the form of microseismic events. It is challenging to analyze the surface-waves on the recorded data directly because of the randomness of their source and their unknown source signatures. I use seismic interferometry to extract the surface-wave arrivals. Interferometry is a powerful tool to extract waves (including body-wave and surface-waves) that propagate from any receiver in the array (called a pseudo source) to the other receivers across the array. Since most of the noise sources in surface microseismic data lie on the surface, seismic interferometry yields pseudo source gathers dominated by surface-wave energy. The dispersive characteristics of these surface-waves are important properties that can be used to extract information necessary for suppressing these waves. I demonstrate the application of interferometry to surface passive data recorded during the hydraulic fracturing operation of a tight gas reservoir and extract the dispersion properties of surface-waves corresponding to a pseudo-shot gather. Comparison of the dispersion characteristics of the surface waves from the pseudo-shot gather with that of an active shot-gather shows interesting similarities and differences. The dispersion character (e.g. velocity change with frequency) of the fundamental mode was observed to have the same behavior for both the active and passive data. However, for the higher mode surface-waves, the dispersion properties are extracted at different frequency ranges. Conventional noise suppression techniques in passive data are mostly stacking-based that rely on enforcing the amplitude of the signal by stacking the waveforms at the receivers and are unable to preserve the waveforms at the individual receivers necessary for estimating the microseismic source location and source mechanism. Here, I introduce a technique based on the tau - p transform, that effectively identifies and separates microseismic events from surface-wave noise in the tau -p domain. This technique is superior to conventional stacking-based noise suppression techniques, because it preserves the waveforms at individual receivers. Application of this methodology to microseismic events with isotropic and double-couple source mechanism, show substantial improvement in the signal-to-noise ratio. Imaging of the processed field data also show improved imaging of the hypocenter location of the microseismic source. In the case of double-couple source mechanism, I suggest two approaches for unifying the polarities at the receivers, a cross-correlation approach and a semblance-based prediction approach. The semblance-based approach is more effective at unifying the polarities, especially for low signal-to-noise ratio data.

Nozzle for electric dispersion reactor

DOEpatents

Sisson, Warren G.; Basaran, Osman A.; Harris, Michael T.

1998-01-01

A nozzle for an electric dispersion reactor includes two concentric electrodes, the inner one of the two delivering disperse phase fluid into a continuous phase fluid. A potential difference generated by a voltage source creates a dispersing electric field at the end of the inner electrode.

Nozzle for electric dispersion reactor

DOEpatents

Sisson, Warren G.; Basaran, Osman A.; Harris, Michael T.

1995-01-01

A nozzle for an electric dispersion reactor includes two concentric electrodes, the inner one of the two delivering disperse phase fluid into a continuous phase fluid. A potential difference generated by a voltage source creates a dispersing electric field at the end of the inner electrode.

All-fiber mid-infrared difference frequency generation source and its application to molecular dispersion spectroscopy

NASA Astrophysics Data System (ADS)

Krzempek, K.; Abramski, K. M.; Nikodem, M.

2017-09-01

A widely tunable, fully monolithic, mid-infrared difference frequency generation source and its application in the dispersion-spectroscopy-based laser trace gas detection of methane and ethane, near 2938 and 2998 cm-1, is presented. Utilizing a fiber pigtailed nonlinear crystal module radically simplified the optical setup, while maintaining a superb conversion efficiency of 20% W-1. Seeded directly from two laser diodes, the source delivered ~0.5 mW of tunable radiation, which was used in a chirped laser dispersion spectroscopy setup, enabling the highly sensitive detection of hydrocarbons.

Coherent white light amplification

DOEpatents

Jovanovic, Igor; Barty, Christopher P.

2004-05-25

A system for coherent simultaneous amplification of a broad spectral range of light that includes an optical parametric amplifier and a source of a seed pulse is described. A first angular dispersive element is operatively connected to the source of a seed pulse. A first imaging telescope is operatively connected to the first angular dispersive element and operatively connected to the optical parametric amplifier. A source of a pump pulse is operatively connected to the optical parametric amplifier. A second imaging telescope is operatively connected to the optical parametric amplifier and a second angular dispersive element is operatively connected to the second imaging telescope.

Health Risk Assessments for Alumina Refineries

PubMed Central

Coffey, Patrick S.

2014-01-01

Objective: To describe contemporary air dispersion modeling and health risk assessment methodologies applied to alumina refineries and to summarize recent results. Methods: Air dispersion models using emission source and meteorological data have been used to assess ground-level concentrations (GLCs) of refinery emissions. Short-term (1-hour and 24-hour average) GLCs and annual average GLCs have been used to assess acute health, chronic health, and incremental carcinogenic risks. Results: The acute hazard index can exceed 1 close to refineries, but it is typically less than 1 at neighboring residential locations. The chronic hazard index is typically substantially less than 1. The incremental carcinogenic risk is typically less than 10−6. Conclusions: The risks of acute health effects are adequately controlled, and the risks of chronic health effects and incremental carcinogenic risks are negligible around referenced alumina refineries. PMID:24806721

Developing a Short-Period, Fundamental-Mode Rayleigh-Wave Attenuation Model for Asia

NASA Astrophysics Data System (ADS)

Yang, X.; Levshin, A. L.; Barmin, M. P.; Ritzwoller, M. H.

2008-12-01

We are developing a 2D, short-period (12 - 22 s), fundamental-mode Rayleigh-wave attenuation model for Asia. This model can be used to invert for a 3D attenuation model of the Earth's crust and upper mantle as well as to implement more accurate path corrections in regional surface-wave magnitude calculations. The prerequisite for developing a reliable Rayleigh-wave attenuation model is the availability of accurate fundamental-mode Rayleigh-wave amplitude measurements. Fundamental-mode Rayleigh-wave amplitudes could be contaminated by a variety of sources such as multipathing, focusing and defocusing, body wave, higher-mode surface wave, and other noise sources. These contaminations must be reduced to the largest extent possible. To achieve this, we designed a procedure by taking advantage of certain Rayleigh-wave characteristics, such as dispersion and elliptical particle motion, for accurate amplitude measurements. We first analyze the dispersion of the surface-wave data using a spectrogram. Based on the characteristics of the data dispersion, we design a phase-matched filter by using either a manually picked dispersion curve, or a group-velocity-model predicted dispersion curve, or the dispersion of the data, and apply the filter to the seismogram. Intelligent filtering of the seismogram and windowing of the resulting cross-correlation based on the spectrogram analysis and the comparison between the phase-match filtered data spectrum, the raw-data spectrum and the theoretical source spectrum effectively reduces amplitude contaminations and results in reliable amplitude measurements in many cases. We implemented these measuring techniques in a graphic-user-interface tool called Surface Wave Amplitude Measurement Tool (SWAMTOOL). Using the tool, we collected and processed waveform data for 200 earthquakes occurring throughout 2003-2006 inside and around Eurasia. The records from 135 broadband stations were used. After obtaining the Rayleigh-wave amplitude measurements, we analyzed the attenuation behavior of the amplitudes using source- and receiver-specific terms calculated from a 3D velocity model of the region. Based on the results, we removed amplitudes that yielded negative average attenuation coefficients, and included an additional parameter in the inversion to account for the possible bias of the CMT moments. Using the high-quality amplitude measurements in a tomographic inversion, we obtained a fundamental-mode Rayleigh-wave attenuation- coefficient model for periods between 12 and 22 s for Asia and surrounding regions. The inverted attenuation model is consistent with the geological features of Asia. We observe low attenuation in stable regions such as eastern Europe, the Siberian platforms, the Indian shield, the Arabian platform, the Yangtze craton, and others. High attenuation is observed in tectonically active regions such as the Himalayas, the Tian Shan, Pamir and Zagros mountains.

Solar-powered irrigation systems. Technical progress report, July 1977--January 1978

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1978-02-28

Dispersed solar thermal power systems applied to farm irrigation energy needs are analyzed. The 17 western states, containing 84% of nationwide irrigated croplands and consuming 93% of nationwide irrigation energy, have been selected to determine were solar irrigation systems can compete most favorably with conventional energy sources. Financial analysis of farms, according to size and ownership, was accomplished to permit realistic comparative analyses of system lifetime costs. Market potential of optimized systems has been estimated for the 17-state region for near-term (1985) and intermediate-term (2000) applications. Technical, economic, and institutional factors bearing on penetration and capture of this market aremore » being identified.« less

Nozzle for electric dispersion reactor

DOEpatents

Sisson, Warren G.; Harris, Michael T.; Scott, Timothy C.; Basaran, Osman A.

1998-01-01

A nozzle for an electric dispersion reactor includes two coaxial cylindrical bodies, the inner one of the two delivering disperse phase fluid into a continuous phase fluid. A potential difference generated by a voltage source creates a dispersing electric field at the end of the inner electrode.

Nozzle for electric dispersion reactor

DOEpatents

Sisson, Warren G.; Harris, Michael T.; Scott, Timothy C.; Basaran, Osman A.

1996-01-01

A nozzle for an electric dispersion reactor includes two coaxial cylindrical bodies, the inner one of the two delivering disperse phase fluid into a continuous phase fluid. A potential difference generated by a voltage source creates a dispersing electric field at the end of the inner electrode.

Nozzle for electric dispersion reactor

DOEpatents

Sisson, W.G.; Basaran, O.A.; Harris, M.T.

1998-04-14

A nozzle for an electric dispersion reactor includes two concentric electrodes, the inner one of the two delivering disperse phase fluid into a continuous phase fluid. A potential difference generated by a voltage source creates a dispersing electric field at the end of the inner electrode. 4 figs.

Nozzle for electric dispersion reactor

DOEpatents

Sisson, W.G.; Basaran, O.A.; Harris, M.T.

1995-11-07

A nozzle for an electric dispersion reactor includes two concentric electrodes, the inner one of the two delivering disperse phase fluid into a continuous phase fluid. A potential difference generated by a voltage source creates a dispersing electric field at the end of the inner electrode. 4 figs.

A framework for emissions source apportionment in industrial areas: MM5/CALPUFF in a near-field application.

PubMed

Ghannam, K; El-Fadel, M

2013-02-01

This paper examines the relative source contribution to ground-level concentrations of carbon monoxide (CO), nitrogen dioxide (NO2), and PM10 (particulate matter with an aerodynamic diameter < 10 microm) in a coastal urban area due to emissions from an industrial complex with multiple stacks, quarrying activities, and a nearby highway. For this purpose, an inventory of CO, oxide of nitrogen (NO(x)), and PM10 emissions was coupled with the non-steady-state Mesoscale Model 5/California Puff Dispersion Modeling system to simulate individual source contributions under several spatial and temporal scales. As the contribution of a particular source to ground-level concentrations can be evaluated by simulating this single-source emissions or otherwise total emissions except that source, a set of emission sensitivity simulations was designed to examine if CALPUFF maintains a linear relationship between emission rates and predicted concentrations in cases where emitted plumes overlap and chemical transformations are simulated. Source apportionment revealed that ground-level releases (i.e., highway and quarries) extended over large areas dominated the contribution to exposure levels over elevated point sources, despite the fact that cumulative emissions from point sources are higher. Sensitivity analysis indicated that chemical transformations of NO(x) are insignificant, possibly due to short-range plume transport, with CALPUFF exhibiting a linear response to changes in emission rate. The current paper points to the significance of ground-level emissions in contributing to urban air pollution exposure and questions the viability of the prevailing paradigm of point-source emission reduction, especially that the incremental improvement in air quality associated with this common abatement strategy may not accomplish the desirable benefit in terms of lower exposure with costly emissions capping. The application of atmospheric dispersion models for source apportionment helps in identifying major contributors to regional air pollution. In industrial urban areas where multiple sources with different geometry contribute to emissions, ground-level releases extended over large areas such as roads and quarries often dominate the contribution to ground-level air pollution. Industrial emissions released at elevated stack heights may experience significant dilution, resulting in minor contribution to exposure at ground level. In such contexts, emission reduction, which is invariably the abatement strategy targeting industries at a significant investment in control equipment or process change, may result in minimal return on investment in terms of improvement in air quality at sensitive receptors.

On tide-induced Lagrangian residual current and residual transport: 2. Residual transport with application in south San Francisco Bay, California

USGS Publications Warehouse

Feng, Shizuo; Cheng, Ralph T.; Pangen, Xi

1986-01-01

The transports of solutes and other tracers are fundamental to estuarine processes. The apparent transport mechanisms are convection by tidal current and current-induced shear effect dispersion for processes which take place in a time period of the order of a tidal cycle. However, as emphasis is shifted toward the effects of intertidal processes, the net transport is mainly determined by tide-induced residual circulation and by residual circulation due to other processes. The commonly used intertidal conservation equation takes the form of a convection-dispersion equation in which the convective velocity is the Eulerian residual current, and the dispersion terms are often referred to as the phase effect dispersion or, sometimes, as the “tidal dispersion.” The presence of these dispersion terms is merely the result of a Fickian type hypothesis. Since the actual processes are not Fickian, thus a Fickian hypothesis obscures the physical significance of this equation. Recent research results on residual circulation have suggested that long-term transport phenomena are closely related to the Lagrangian residual current or the Lagrangian residual transport. In this paper a new formulation of an intertidal conservation equation is presented and examined in detail. In a weakly nonlinear tidal estuary the resultant intertidal transport equation also takes the form of a convection-dispersion equation without the ad hoc introduction of phase effect dispersion in a form of dispersion tensor. The convective velocity in the resultant equation is the first-order Lagrangian residual current (the sum of the Eulerian residual current and the Stokes drift). The remaining dispersion terms are important only in higher-order solutions; they are due to shear effect dispersion and turbulent mixing. There exists a dispersion boundary layer adjacent to shoreline boundaries. An order of magnitude estimate of the properties in the dispersion boundary layer is given. The present treatment of intertidal transport processes is illustrated by an analytical solution for an amphidromic system and by a numerical application in South San Francisco Bay, California. The present formulation reveals that the mechanism for long-term transport of solutes is mainly convection due to the Lagrangian residual current in the interior of a tidal estuary. This result also points out the weakness in the tidal dispersion formulation, and explains the large variability of the observed values for tidal dispersion coefficients. Further research on properties of the dispersion boundary layer is needed.

GPS tracking of non-breeding ravens reveals the importance of anthropogenic food sources during their dispersal in the Eastern Alps.

PubMed

Loretto, Matthias-Claudio; Schuster, Richard; Bugnyar, Thomas

2016-08-01

In many songbirds, the space use of breeders is well studied but poorly understood for non-breeders. In common ravens, some studies of non-breeders indicate high vagrancy with large individual differences in home range size, whereas others show that up to 40% of marked non-breeders can be regularly observed at the same anthropogenic food source over months to years. The aim of this study was to provide new insights on ravens' behavior during dispersal in the Eastern Alps. We deployed Global Positioning System (GPS) loggers on 10 individuals to gather accurate spatial and temporal information on their movements to quantify: 1) the dimension of the birds' space use (home range size with seasonal effects and daily/long-term travel distances), 2) how long they stayed in a dispersal stage of wandering as opposed to settling temporarily, and 3) their destination of movements. We recorded movements of up to 40 km per hour, more than 160 km within 1 day and more than 11,000 km within 20 months, indicating high vagrancy. Switching frequently between temporarily settling and travelling large distances in short time intervals leads to extensive home ranges, which also explains and combines the different findings in the literature. The destinations are rich anthropogenic food sources, where the birds spent on average 75% of their time. We discuss how ravens may find these "feeding hot spots" and which factors may influence their decision to stay/leave a site. The strong dependence on anthropogenic resources found in this population may have implications for site management and conservation issues.

Short-term gas dispersion in idealised urban canopy in street parallel with flow direction

NASA Astrophysics Data System (ADS)

Chaloupecká, Hana; Jaňour, Zbyněk; Nosek, Štěpán

2016-03-01

Chemical attacks (e.g. Syria 2014-15 chlorine, 2013 sarine or Iraq 2006-7 chlorine) as well as chemical plant disasters (e.g. Spain 2015 nitric oxide, ferric chloride; Texas 2014 methyl mercaptan) threaten mankind. In these crisis situations, gas clouds are released. Dispersion of gas clouds is the issue of interest investigated in this paper. The paper describes wind tunnel experiments of dispersion from ground level point gas source. The source is situated in a model of an idealised urban canopy. The short duration releases of passive contaminant ethane are created by an electromagnetic valve. The gas cloud concentrations are measured in individual places at the height of the human breathing zone within a street parallel with flow direction by Fast-response Ionisation Detector. The simulations of the gas release for each measurement position are repeated many times under the same experimental set up to obtain representative datasets. These datasets are analysed to compute puff characteristics (arrival, leaving time and duration). The results indicate that the mean value of the dimensionless arrival time can be described as a growing linear function of the dimensionless coordinate in the street parallel with flow direction where the gas source is situated. The same might be stated about the dimensionless leaving time as well as the dimensionless duration, however these fits are worse. Utilising a linear function, we might also estimate some other statistical characteristics from datasets than the datasets means (medians, trimeans). The datasets of the dimensionless arrival time, the dimensionless leaving time and the dimensionless duration can be fitted by the generalized extreme value distribution (GEV) in all sampling positions except one.

Nozzle for electric dispersion reactor

DOEpatents

Sisson, W.G.; Harris, M.T.; Scott, T.C.; Basaran, O.A.

1996-04-02

A nozzle for an electric dispersion reactor includes two coaxial cylindrical bodies, the inner one of the two delivering disperse phase fluid into a continuous phase fluid. A potential difference generated by a voltage source creates a dispersing electric field at the end of the inner electrode. 5 figs.

Nozzle for electric dispersion reactor

DOEpatents

Sisson, W.G.; Harris, M.T.; Scott, T.C.; Basaran, O.A.

1998-06-02

A nozzle for an electric dispersion reactor includes two coaxial cylindrical bodies, the inner one of the two delivering disperse phase fluid into a continuous phase fluid. A potential difference generated by a voltage source creates a dispersing electric field at the end of the inner electrode. 5 figs.

Simulation of time-dispersion spectral device with sample spectra accumulation

NASA Astrophysics Data System (ADS)

Zhdanov, Arseny; Khansuvarov, Ruslan; Korol, Georgy

2014-09-01

This research is conducted in order to design a spectral device for light sources power spectrum analysis. The spectral device should process radiation from sources, direct contact with radiation of which is either impossible or undesirable. Such sources include jet blast of an aircraft, optical radiation in metallurgy and textile industry. In proposed spectral device optical radiation is guided out of unfavorable environment via a piece of optical fiber with high dispersion. It is necessary for analysis to make samples of analyzed radiation as short pulses. Dispersion properties of such optical fiber cause spectral decomposition of input optical pulses. The faster time of group delay vary the stronger the spectral decomposition effect. This effect allows using optical fiber with high dispersion as a major element of proposed spectral device. Duration of sample must be much shorter than group delay time difference of a dispersive system. In the given frequency range this characteristic has to be linear. The frequency range is 400 … 500 THz for typical optical fiber. Using photonic-crystal fiber (PCF) gives much wider spectral range for analysis. In this paper we propose simulation of single pulse transmission through dispersive system with linear dispersion characteristic and quadratic-detected output responses accumulation. During simulation we propose studying influence of optical fiber dispersion characteristic angle on spectral measurement results. We also consider pulse duration and group delay time difference impact on output pulse shape and duration. Results show the most suitable dispersion characteristic that allow choosing the structure of PCF - major element of time-dispersion spectral analysis method and required number of samples for reliable assessment of measured spectrum.

Reliable prediction of three-body intermolecular interactions using dispersion-corrected second-order Møller-Plesset perturbation theory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, Yuanhang; Beran, Gregory J. O., E-mail: gregory.beran@ucr.edu

2015-07-28

Three-body and higher intermolecular interactions can play an important role in molecular condensed phases. Recent benchmark calculations found problematic behavior for many widely used density functional approximations in treating 3-body intermolecular interactions. Here, we demonstrate that the combination of second-order Møller-Plesset (MP2) perturbation theory plus short-range damped Axilrod-Teller-Muto (ATM) dispersion accurately describes 3-body interactions with reasonable computational cost. The empirical damping function used in the ATM dispersion term compensates both for the absence of higher-order dispersion contributions beyond the triple-dipole ATM term and non-additive short-range exchange terms which arise in third-order perturbation theory and beyond. Empirical damping enables this simplemore » model to out-perform a non-expanded coupled Kohn-Sham dispersion correction for 3-body intermolecular dispersion. The MP2 plus ATM dispersion model approaches the accuracy of O(N{sup 6}) methods like MP2.5 or even spin-component-scaled coupled cluster models for 3-body intermolecular interactions with only O(N{sup 5}) computational cost.« less

“RLINE: A Line Source Dispersion Model for Near-Surface Releases”

EPA Science Inventory

Growing concern about human exposure and related adverse health effects near roadways initiated an effort by the U. S. Environmental Protection Agency to reexamine the dispersion of mobile source related pollutants. These adverse effects, in combination with the fact that a signi...

Non-Fickian dispersive transport of strontium in laboratory-scale columns: Modelling and evaluation

NASA Astrophysics Data System (ADS)

Liu, Dongxu; Jivkov, Andrey P.; Wang, Lichun; Si, Gaohua; Yu, Jing

2017-06-01

In the context of environmental remediation of contaminated sites and safety assessment of nuclear waste disposal in the near-surface zone, we investigate the leaching and non-Fickian dispersive migration with sorption of strontium (mocking strontium-90) through columns packed with sand and clay. Analysis is based on breakthrough curves (BTCs) from column experiments, which simulated rainfall infiltration and source term release scenario, rather than applying constant tracer solution at the inlet as commonly used. BTCs are re-evaluated and transport parameters are estimated by inverse modelling using two approaches: (1) equilibrium advection-dispersion equation (ADE); and (2) continuous time random walk (CTRW). Firstly, based on a method for calculating leach concentration, the inlet condition with an exponential decay input is identified. Secondly, the results show that approximately 39%-58% of Br- and 16%-49% of Sr2+ are eluted from the columns at the end of the breakthrough experiments. This suggests that trapping mechanisms, including diffusion into immobile zones and attachment of tracer on mineral surfaces, are more pronounced for Sr2+ than for Br-. Thirdly, we demonstrate robustness of CTRW-based truncated power-law (TPL) model in capturing non-Fickian reactive transport with 0 < β < 2, and Fickian transport with β > 2. The non-Fickian dispersion observed experimentally is explained by variations of local flow field from preferential flow paths due to physical heterogeneities. Particularly, the additional sorption process of strontium on clay minerals contributes to the delay of the peak concentration and the tailing features, which leads to an enhanced non-Fickian transport for strontium. Finally, the ADE and CTRW approaches to environmental modelling are evaluated. It is shown that CTRW with a sorption term can describe non-Fickian dispersive transport of strontium at laboratory scale by identifying appropriate parameters, while the traditional ADE with a retardation factor fails to reproduce the complex non-Fickian transport of strontium with strong sorption on clay surface.

Correcting STIS CCD Point-Source Spectra for CTE Loss

NASA Technical Reports Server (NTRS)

Goudfrooij, Paul; Bohlin, Ralph C.; Maiz-Apellaniz, Jesus

2006-01-01

We review the on-orbit spectroscopic observations that are being used to characterize the Charge Transfer Efficiency (CTE) of the STIS CCD in spectroscopic mode. We parameterize the CTE-related loss for spectrophotometry of point sources in terms of dependencies on the brightness of the source, the background level, the signal in the PSF outside the standard extraction box, and the time of observation. Primary constraints on our correction algorithm are provided by measurements of the CTE loss rates for simulated spectra (images of a tungsten lamp taken through slits oriented along the dispersion axis) combined with estimates of CTE losses for actual spectra of spectrophotometric standard stars in the first order CCD modes. For point-source spectra at the standard reference position at the CCD center, CTE losses as large as 30% are corrected to within approx.1% RMS after application of the algorithm presented here, rendering the Poisson noise associated with the source detection itself to be the dominant contributor to the total flux calibration uncertainty.

Rafting rocks reveal marine biological dispersal: A case study using clasts from beach-cast macroalgal holdfasts

NASA Astrophysics Data System (ADS)

Garden, Christopher J.; Craw, Dave; Waters, Jonathan M.; Smith, Abigail

2011-12-01

Tracking and quantifying biological dispersal presents a major challenge in marine systems. Most existing methods for measuring dispersal are limited by poor resolution and/or high cost. Here we use geological data to quantify the frequency of long-distance dispersal in detached bull-kelp (Phaeophyceae: Durvillaea) in southern New Zealand. Geological resolution in this region is enhanced by the presence of a number of distinct and readily-identifiable geological terranes. We sampled 13,815 beach-cast bull-kelp plants across 130 km of coastline. Rocks were found attached to 2639 of the rafted plants, and were assigned to specific geological terranes (source regions) to quantify dispersal frequencies and distances. Although the majority of kelp-associated rock specimens were found to be locally-derived, a substantial number (4%) showed clear geological evidence of long-distance dispersal, several having travelled over 200 km from their original source regions. The proportion of local versus foreign clasts varied considerably between regions. While short-range dispersal clearly predominates, long-distance travel of detached bull-kelp plants is shown to be a common and ongoing process that has potential to connect isolated coastal populations. Geological analyses represent a cost-effective and powerful method for assigning large numbers of drifted macroalgae to their original source regions.

The Relationship of Revenue Dispersion to Several Indicators of Institutional Financial Conditions.

ERIC Educational Resources Information Center

Taylor, Barbara A.

The relationship between revenue dispersion and several indicators of financial condition in four-year colleges and universities was studied. Revenue dispersion is a measure of the diversity of institutional income sources. It was hypothesized that revenue dispersion would be positively related to financial condition, since variants on…

Pollen flow of wheat under natural conditions in the Huanghuai River Wheat Region, China

PubMed Central

Sun, Ai-Qing; Zhang, Chun-Qing; Wu, Cheng-Lai; Gao, Qing-Rong

2015-01-01

abstract The transgenic pollen spread is the main pathway of transgenic plant gene flow. The maximum distance of pollen dispersal (horizontal), the spatial dynamics of pollen movement (vertical), and the patterns of pollen dispersal are important considerations in biosafety assessments of genetically modified crops. To evaluate wheat (Triticum aestivum) pollen dispersal, we measured the pollen suspension velocity and analyzed pollen dispersal patterns under natural conditions in the Huanghuai River wheat-growing region in 2009. The pollen suspension velocity was 0.3–0.4 m/s. The highest pollen densities were detected in the north, northwest, and south of the pollen source. Pollen was dispersed over distances greater than 245 m in the northwest and northeast directions. At the pollen source center, pollen density decreased with increasing vertical height. In the north of the pollen source, the pollen density from 65 m to 225 m showed a wave-mode decrease with increasing height. The horizontal transport of pollen over longer distances fitted polynomial equations. In the north, the pollen density was highest at 45 m from the pollen source, and decreased with increasing distance. In the northwest, the pollen density showed a double-peak trend. In the northeast, pollen density was highest from 45 m to 125 m from the source. Wind speeds greater than the pollen suspension velocity and the duration of continuous gusts were the main factors affecting pollen dispersal. This information will be useful for determining the spatial isolation distances for hybrid seed production and for the commercial production of transgenic wheat. PMID:25658025

Regeneration of Airy pulses in fiber-optic links with dispersion management of the two leading dispersion terms of opposite signs

NASA Astrophysics Data System (ADS)

Driben, R.; Meier, T.

2014-04-01

Dispersion management of periodically alternating fiber sections with opposite signs of two leading dispersion terms is applied for the regeneration of self-accelerating truncated Airy pulses. It is demonstrated that for such a dispersion management scheme, the direction of the acceleration of the pulse is reversed twice within each period. In this scheme the system features light hot spots in the center of each fiber section, where the energy of the light pulse is tightly focused in a short temporal slot. Comprehensive numerical studies demonstrate a long-lasting propagation also under the influence of a strong fiber Kerr nonlinearity.

Dispersal Limitations on Fish Community Recovery Following Long-term Water Quality Remediation

DOE PAGES

McManamay, Ryan A.; Jett, Robert T.; Ryon, Michael G.; ...

2016-02-22

Holistic restoration approaches, such as water quality remediation, are likely to meet conservation objectives because they are typically implemented at watershed scales, as opposed to individual stream reaches. However, habitat fragmentation may impose constraints on the ecological effectiveness of holistic restoration strategies by limiting colonization following remediation. We questioned the importance of dispersal limitations to fish community recovery following long-term water quality remediation and species reintroductions across the White Oak Creek (WOC) watershed near Oak Ridge, Tennessee (USA). Long-term (26 years) responses in fish species richness and biomass to water quality remediation were evaluated in light of habitat fragmentation andmore » population isolation from instream barriers, which varied in their passage potential. In addition, ordination techniques were used to determine the relative importance of habitat connectivity and water quality, in explaining variation fish communities relative to environmental fluctuations, i.e. streamflow. Ecological recovery (changes in richness) at each site was negatively related to barrier index, a measure of community isolation by barriers relative to stream distance. Following species reintroductions, dispersal by fish species was consistently in the downstream direction and upstream passage above barriers was non-existent. The importance of barrier index in explaining variation in fish communities was stronger during higher flow conditions, but decreased over time an indication of increasing community stability and loss of seasonal migrants. Compared to habitat fragmentation, existing water quality concerns (i.e., outfalls, point source discharges) were unrelated to ecological recovery, but explained relatively high variation in community dynamics. Our results suggest that habitat fragmentation limited the ecological effectiveness of intensive water quality remediation efforts and fish reintroduction efforts by impeding recolonization at isolated stream reaches.« less

Dispersal Limitations on Fish Community Recovery Following Long-term Water Quality Remediation

DOE Office of Scientific and Technical Information (OSTI.GOV)

McManamay, Ryan A.; Jett, Robert T.; Ryon, Michael G.

Holistic restoration approaches, such as water quality remediation, are likely to meet conservation objectives because they are typically implemented at watershed scales, as opposed to individual stream reaches. However, habitat fragmentation may impose constraints on the ecological effectiveness of holistic restoration strategies by limiting colonization following remediation. We questioned the importance of dispersal limitations to fish community recovery following long-term water quality remediation and species reintroductions across the White Oak Creek (WOC) watershed near Oak Ridge, Tennessee (USA). Long-term (26 years) responses in fish species richness and biomass to water quality remediation were evaluated in light of habitat fragmentation andmore » population isolation from instream barriers, which varied in their passage potential. In addition, ordination techniques were used to determine the relative importance of habitat connectivity and water quality, in explaining variation fish communities relative to environmental fluctuations, i.e. streamflow. Ecological recovery (changes in richness) at each site was negatively related to barrier index, a measure of community isolation by barriers relative to stream distance. Following species reintroductions, dispersal by fish species was consistently in the downstream direction and upstream passage above barriers was non-existent. The importance of barrier index in explaining variation in fish communities was stronger during higher flow conditions, but decreased over time an indication of increasing community stability and loss of seasonal migrants. Compared to habitat fragmentation, existing water quality concerns (i.e., outfalls, point source discharges) were unrelated to ecological recovery, but explained relatively high variation in community dynamics. Our results suggest that habitat fragmentation limited the ecological effectiveness of intensive water quality remediation efforts and fish reintroduction efforts by impeding recolonization at isolated stream reaches.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Werth, David; Buckley, Robert

Here, the detectability of emission sources, defined by a low-level of mixing with other sources, was estimated for various locations surrounding the Sea of Japan, including a site within North Korea. A high-resolution meteorological model coupled to a dispersion model was used to simulate plume dynamics for four periods, and two metrics of airborne plume mixing were calculated for each source. While emissions from several known sources in this area tended to blend with others while dispersing downwind, the North Korean plume often remained relatively distinct, thereby making it potentially easier to unambiguously ‘backtrack’ it to its source.

Crosswell electromagnetic modeling from impulsive source: Optimization strategy for dispersion suppression in convolutional perfectly matched layer

PubMed Central

Fang, Sinan; Pan, Heping; Du, Ting; Konaté, Ahmed Amara; Deng, Chengxiang; Qin, Zhen; Guo, Bo; Peng, Ling; Ma, Huolin; Li, Gang; Zhou, Feng

2016-01-01

This study applied the finite-difference time-domain (FDTD) method to forward modeling of the low-frequency crosswell electromagnetic (EM) method. Specifically, we implemented impulse sources and convolutional perfectly matched layer (CPML). In the process to strengthen CPML, we observed that some dispersion was induced by the real stretch κ, together with an angular variation of the phase velocity of the transverse electric plane wave; the conclusion was that this dispersion was positively related to the real stretch and was little affected by grid interval. To suppress the dispersion in the CPML, we first derived the analytical solution for the radiation field of the magneto-dipole impulse source in the time domain. Then, a numerical simulation of CPML absorption with high-frequency pulses qualitatively amplified the dispersion laws through wave field snapshots. A numerical simulation using low-frequency pulses suggested an optimal parameter strategy for CPML from the established criteria. Based on its physical nature, the CPML method of simply warping space-time was predicted to be a promising approach to achieve ideal absorption, although it was still difficult to entirely remove the dispersion. PMID:27585538

Long-distance plant dispersal to North Atlantic islands: colonization routes and founder effect

PubMed Central

Alsos, Inger Greve; Ehrich, Dorothee; Eidesen, Pernille Bronken; Solstad, Heidi; Westergaard, Kristine Bakke; Schönswetter, Peter; Tribsch, Andreas; Birkeland, Siri; Elven, Reidar; Brochmann, Christian

2015-01-01

Long-distance dispersal (LDD) processes influence the founder effect on islands. We use genetic data for 25 Atlantic species and similarities among regional floras to analyse colonization, and test whether the genetic founder effect on five islands is associated with dispersal distance, island size and species traits. Most species colonized postglacially via multiple dispersal events from several source regions situated 280 to >3000 km away, and often not from the closest ones. A strong founder effect was observed for insect-pollinated mixed maters, and it increased with dispersal distance and decreased with island size in accordance with the theory of island biogeography. Only a minor founder effect was observed for wind-pollinated outcrossing species. Colonization patterns were largely congruent, indicating that despite the importance of stochasticity, LDD is mainly determined by common factors, probably dispersal vectors. Our findings caution against a priori assuming a single, close source region in biogeographic analyses. PMID:25876627

Source mechanisms of volcanic tsunamis.

PubMed

Paris, Raphaël

2015-10-28

Volcanic tsunamis are generated by a variety of mechanisms, including volcano-tectonic earthquakes, slope instabilities, pyroclastic flows, underwater explosions, shock waves and caldera collapse. In this review, we focus on the lessons that can be learnt from past events and address the influence of parameters such as volume flux of mass flows, explosion energy or duration of caldera collapse on tsunami generation. The diversity of waves in terms of amplitude, period, form, dispersion, etc. poses difficulties for integration and harmonization of sources to be used for numerical models and probabilistic tsunami hazard maps. In many cases, monitoring and warning of volcanic tsunamis remain challenging (further technical and scientific developments being necessary) and must be coupled with policies of population preparedness. © 2015 The Author(s).

Catchment-scale environmental controls of sediment-associated contaminant dispersal

NASA Astrophysics Data System (ADS)

Macklin, Mark

2010-05-01

Globally river sediment associated contaminants, most notably heavy metals, radionuclides, Polychlorinated Biphenyls (PCBs), Organochlorine pesticides (OCs) and phosphorous, constitute one the most significant long-term risks to ecosystems and human health. These can impact both urban and rural areas and, because of their prolonged environmental residence times, are major sources of secondary pollution if contaminated soil and sediment are disturbed by human activity or by natural processes such as water or wind erosion. River catchments are also the primary source of sediment-associated contaminants to the coastal zone, and to the ocean, and an understanding of the factors that control contaminated sediment fluxes and delivery in river systems is essential for effective environmental management and protection. In this paper the catchment-scale controls of sediment-associated contaminant dispersal are reviewed, including climate-related variations in flooding regime, land-use change, channel engineering, restoration and flood defence. Drawing on case studies from metal mining impacted catchments in Bolivia (Río Pilcomayo), Spain (Río Guadiamar), Romania (River Tisa) and the UK (River Swale) some improved methodologies for identifying, tracing, modelling and managing contaminated river sediments are proposed that could have more general application in similarly affected river systems worldwide.

Possible consequences of severe accidents at the Lubiatowo site, Poland

NASA Astrophysics Data System (ADS)

Seibert, Petra; Philipp, Anne; Hofman, Radek; Gufler, Klaus; Sholly, Steven

2014-05-01

The construction of a nuclear power plant is under consideration in Poland. One of the sites under discussion is near Lubiatowo, located on the cost of the Baltic Sea northwest of Gdansk. An assessment of possible environmental consequences is carried out for 88 real meteorological cases with the Lagrangian particle dispersion model FLEXPART. Based on literature research, three reactor designs (ABWR, EPR, AP 1000) were identified as being under discussion in Poland. For each of the designs, a set of accident scenarios was evaluated and two source terms per reactor design were selected for analysis. One of the selected source terms was a relatively large release while the second one was a severe accident with an intact containment. Considered endpoints of the calculations are ground contamination with Cs-137 and time-integrated concentrations of I-131 in air as well as committed doses. They are evaluated on a grid of ca. 3 km mesh size covering eastern Central Europe.

PAGAN

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chu, M.S.Y.

1990-12-01

The PAGAN code system is a part of the performance assessment methodology developed for use by the U.S. Nuclear Regulatory Commission in evaluating license applications for low-level waste disposal facilities. In this methodology, PAGAN is used as one candidate approach for analysis of the ground-water pathway. PAGAN, Version 1.1. has the capability to model the source term, vadose-zone transport, and aquifer transport of radionuclides from a waste disposal unit. It combines the two codes SURFACE and DISPERSE which are used as semi-analytical solutions to the convective-dispersion equation. This system uses menu driven input/out for implementing a simple ground-water transport analysismore » and incorporates statistical uncertainty functions for handling data uncertainties. The output from PAGAN includes a time and location-dependent radionuclide concentration at a well in the aquifer, or a time and location-dependent radionuclide flux into a surface-water body.« less

Calibration of semi-stochastic procedure for simulating high-frequency ground motions

USGS Publications Warehouse

Seyhan, Emel; Stewart, Jonathan P.; Graves, Robert

2013-01-01

Broadband ground motion simulation procedures typically utilize physics-based modeling at low frequencies, coupled with semi-stochastic procedures at high frequencies. The high-frequency procedure considered here combines deterministic Fourier amplitude spectra (dependent on source, path, and site models) with random phase. Previous work showed that high-frequency intensity measures from this simulation methodology attenuate faster with distance and have lower intra-event dispersion than in empirical equations. We address these issues by increasing crustal damping (Q) to reduce distance attenuation bias and by introducing random site-to-site variations to Fourier amplitudes using a lognormal standard deviation ranging from 0.45 for Mw < 7 to zero for Mw 8. Ground motions simulated with the updated parameterization exhibit significantly reduced distance attenuation bias and revised dispersion terms are more compatible with those from empirical models but remain lower at large distances (e.g., > 100 km).

Variational Iterative Refinement Source Term Estimation Algorithm Assessment for Rural and Urban Environments

NASA Astrophysics Data System (ADS)

Delle Monache, L.; Rodriguez, L. M.; Meech, S.; Hahn, D.; Betancourt, T.; Steinhoff, D.

2016-12-01

It is necessary to accurately estimate the initial source characteristics in the event of an accidental or intentional release of a Chemical, Biological, Radiological, or Nuclear (CBRN) agent into the atmosphere. The accurate estimation of the source characteristics are important because many times they are unknown and the Atmospheric Transport and Dispersion (AT&D) models rely heavily on these estimates to create hazard assessments. To correctly assess the source characteristics in an operational environment where time is critical, the National Center for Atmospheric Research (NCAR) has developed a Source Term Estimation (STE) method, known as the Variational Iterative Refinement STE algorithm (VIRSA). VIRSA consists of a combination of modeling systems. These systems include an AT&D model, its corresponding STE model, a Hybrid Lagrangian-Eulerian Plume Model (H-LEPM), and its mathematical adjoint model. In an operational scenario where we have information regarding the infrastructure of a city, the AT&D model used is the Urban Dispersion Model (UDM) and when using this model in VIRSA we refer to the system as uVIRSA. In all other scenarios where we do not have the city infrastructure information readily available, the AT&D model used is the Second-order Closure Integrated PUFF model (SCIPUFF) and the system is referred to as sVIRSA. VIRSA was originally developed using SCIPUFF 2.4 for the Defense Threat Reduction Agency and integrated into the Hazard Prediction and Assessment Capability and Joint Program for Information Systems Joint Effects Model. The results discussed here are the verification and validation of the upgraded system with SCIPUFF 3.0 and the newly implemented UDM capability. To verify uVIRSA and sVIRSA, synthetic concentration observation scenarios were created in urban and rural environments and the results of this verification are shown. Finally, we validate the STE performance of uVIRSA using scenarios from the Joint Urban 2003 (JU03) experiment, which was held in Oklahoma City and also validate the performance of sVIRSA using scenarios from the FUsing Sensor Integrated Observing Network (FUSION) Field Trial 2007 (FFT07), held at Dugway Proving Grounds in rural Utah.

N, S co-doped carbon spheres with highly dispersed CoO as non-precious metal catalyst for oxygen reduction reaction

NASA Astrophysics Data System (ADS)

Chen, Linlin; Guo, Xingpeng; Zhang, Guoan

2017-08-01

It is still a great challenge in preparing non-precious metal catalysts with high activity and long-term stability to substitute for precious metal catalysts for oxygen reduction reaction (ORR) in fuel cells. Herein, we report a novel and facile catalyst-N, S co-doped carbon spheres with highly dispersed CoO (CoO@NS-CSs), where biomass glucose spheres act as carbon precursor and H2S, NH3 derived from the decomposition of thiourea not only provide N, S sources but also can etch carbon spheres to produce nanoporous structure. CoO@NS-CSs catalyst exhibits excellent ORR activity with a high onset potential of 0.946 V vs. RHE (reversible hydrogen electrode) and a half-wave potential of 0.821 V vs. RHE through a four-electron pathway in alkaline solution, which is comparable to commercial Pt/C catalyst (onset potential: 0.926 V vs. RHE, half-wave potential: 0.827 V vs. RHE). Furthermore, both the long-term stability and methanol-tolerance of CoO@NS-CSs catalyst are superior to those of commercial Pt/C catalyst. The excellent ORR performance of CoO@NS-CSs catalyst can be attributed to its micro-mesopore structure, high specific surface area (667 m2 g-1), and highly dispersed CoO. This work manifests that the obtained CoO@NS-CSs catalyst is promising to be applied to fuel cells.

Exchange-Correlation Effects for Noncovalent Interactions in Density Functional Theory.

PubMed

Otero-de-la-Roza, A; DiLabio, Gino A; Johnson, Erin R

2016-07-12

In this article, we develop an understanding of how errors from exchange-correlation functionals affect the modeling of noncovalent interactions in dispersion-corrected density-functional theory. Computed CCSD(T) reference binding energies for a collection of small-molecule clusters are decomposed via a molecular many-body expansion and are used to benchmark density-functional approximations, including the effect of semilocal approximation, exact-exchange admixture, and range separation. Three sources of error are identified. Repulsion error arises from the choice of semilocal functional approximation. This error affects intermolecular repulsions and is present in all n-body exchange-repulsion energies with a sign that alternates with the order n of the interaction. Delocalization error is independent of the choice of semilocal functional but does depend on the exact exchange fraction. Delocalization error misrepresents the induction energies, leading to overbinding in all induction n-body terms, and underestimates the electrostatic contribution to the 2-body energies. Deformation error affects only monomer relaxation (deformation) energies and behaves similarly to bond-dissociation energy errors. Delocalization and deformation errors affect systems with significant intermolecular orbital interactions (e.g., hydrogen- and halogen-bonded systems), whereas repulsion error is ubiquitous. Many-body errors from the underlying exchange-correlation functional greatly exceed in general the magnitude of the many-body dispersion energy term. A functional built to accurately model noncovalent interactions must contain a dispersion correction, semilocal exchange, and correlation components that minimize the repulsion error independently and must also incorporate exact exchange in such a way that delocalization error is absent.

Visco-instability of shear viscoelastic collisional dusty plasma systems

NASA Astrophysics Data System (ADS)

Mahdavi-Gharavi, M.; Hajisharifi, K.; Mehidan, H.

2018-04-01

In this paper, the stability of Newtonian and non-Newtonian viscoelastic collisional shear-velocity dusty plasmas is studied, using the framework of a generalized hydrodynamic (GH) model. Motivated by Banerjee et al.'s work (Banerjee et al., New J. Phys., vol. 12 (12), 2010, p. 123031), employing linear perturbation theory as well as the local approximation method in the inhomogeneous direction, the dispersion relations of the Fourier modes are obtained for Newtonian and non-Newtonian dusty plasma systems in the presence of a dust-neutral friction term. The analysis of the obtained dispersion relation in the non-Newtonian case shows that the inhomogeneous viscosity force depending on the velocity shear profile can be the genesis of a free energy source which leads the shear system to be unstable. Study of the dust-neutral friction effect on the instability of the considered systems using numerical analysis of the dispersion relation in the Newtonian case demonstrates that the maximum growth rate decreases considerably by increasing the collision frequency in the hydrodynamic regime, while this reduction can be neglected in the kinetic regime. Results show a more significant stabilization role of the dust-neutral friction term in the non-Newtonian cases, through decreasing the maximum growth rate at any fixed wavenumber and construction of the instable wavenumber region. The results of the present investigation will greatly contribute to study of the time evolution of viscoelastic laboratory environments with externally applied shear; where in these experiments the dust-neutral friction process can play a considerable role.

Lectures on Dispersion Theory

DOE R&D Accomplishments Database

Salam, A.

1956-04-01

Lectures with mathematical analysis are given on Dispersion Theory and Causality and Dispersion Relations for Pion-nucleon Scattering. The appendix includes the S-matrix in terms of Heisenberg Operators. (F. S.)

Molecular dispersion spectroscopy for chemical sensing using chirped mid-infrared quantum cascade laser.

PubMed

Wysocki, Gerard; Weidmann, Damien

2010-12-06

A spectroscopic method of molecular detection based on dispersion measurements using a frequency-chirped laser source is presented. An infrared quantum cascade laser emitting around 1912 cm(-1) is used as a tunable spectroscopic source to measure dispersion that occurs in the vicinity of molecular ro-vibrational transitions. The sample under study is a mixture of nitric oxide in dry nitrogen. Two experimental configurations based on a coherent detection scheme are investigated and discussed. The theoretical models, which describe the observed spectral signals, are developed and verified experimentally. The method is particularly relevant to optical sensing based on mid-infrared quantum cascade lasers as the high chirp rates available with those sources can significantly enhance the magnitude of the measured dispersion signals. The method relies on heterodyne beatnote frequency measurements and shows high immunity to variations in the optical power received by the photodetector.

Direct splash dispersal prevails over indirect and subsequent spread during rains in Colletotrichum gloeosporioides infecting yams.

PubMed

Penet, Laurent; Guyader, Sébastien; Pétro, Dalila; Salles, Michèle; Bussière, François

2014-01-01

Plant pathogens have evolved many dispersal mechanisms, using biotic or abiotic vectors or a combination of the two. Rain splash dispersal is known from a variety of fungi, and can be an efficient driver of crop epidemics, with infectious strains propagating rapidly among often genetically homogenous neighboring plants. Splashing is nevertheless a local dispersal process and spores taking the droplet ride seldom move farther than a few decimeters. In this study, we assessed rain splash dispersal of conidia of the yam anthracnose agent, Colletotrichum gloeosporioides, in an experimental setting using a rain simulator, with emphasis on the impact of soil contamination (i.e., effect of re-splashing events). Spores dispersed up to 50 cm from yam leaf inoculum sources, though with an exponential decrease with increasing distance. While few spores were dispersed via re-splash from spore-contaminated soil, the proportion deposited via this mechanism increased with increasing distance from the initial source. We found no soil contamination carryover from previous rains, suggesting that contamination via re-splashing from contaminated soils mainly occurred within single rains. We conclude that most dispersal occurs from direct splashing, with a weaker contribution of indirect dispersal via re-splash.

Direct Splash Dispersal Prevails over Indirect and Subsequent Spread during Rains in Colletotrichum gloeosporioides Infecting Yams

PubMed Central

Penet, Laurent; Guyader, Sébastien; Pétro, Dalila; Salles, Michèle; Bussière, François

2014-01-01

Plant pathogens have evolved many dispersal mechanisms, using biotic or abiotic vectors or a combination of the two. Rain splash dispersal is known from a variety of fungi, and can be an efficient driver of crop epidemics, with infectious strains propagating rapidly among often genetically homogenous neighboring plants. Splashing is nevertheless a local dispersal process and spores taking the droplet ride seldom move farther than a few decimeters. In this study, we assessed rain splash dispersal of conidia of the yam anthracnose agent, Colletotrichum gloeosporioides, in an experimental setting using a rain simulator, with emphasis on the impact of soil contamination (i.e., effect of re-splashing events). Spores dispersed up to 50 cm from yam leaf inoculum sources, though with an exponential decrease with increasing distance. While few spores were dispersed via re-splash from spore-contaminated soil, the proportion deposited via this mechanism increased with increasing distance from the initial source. We found no soil contamination carryover from previous rains, suggesting that contamination via re-splashing from contaminated soils mainly occurred within single rains. We conclude that most dispersal occurs from direct splashing, with a weaker contribution of indirect dispersal via re-splash. PMID:25532124

Characterization of pollutant dispersion near elongated ...

EPA Pesticide Factsheets

This paper presents a wind tunnel study of the effects of elongated rectangular buildings on the dispersion of pollutants from nearby stacks. The study examines the influence of source location, building aspect ratio, and wind direction on pollutant dispersion with the goal of developing improved algorithms within dispersion models. The paper also examines the current AERMOD/PRIME modeling capabilities compared to wind tunnel observations. Differences in the amount of plume material entrained in the wake region downwind of a building for various source locations and source heights are illustrated with vertical and lateral concentration profiles. These profiles were parameterized using the Gaussian equation and show the influence of building/source configurations on those parameters. When the building is oriented at 45° to the approach flow, for example, the effective plume height descends more rapidly than it does for a perpendicular building, enhancing the resulting surface concentrations in the wake region. Buildings at angles to the wind cause a cross-wind shift in the location of the plume resulting from a lateral mean flow established in the building wake. These and other effects that are not well represented in many dispersion models are important considerations when developing improved algorithms to estimate the location and magnitude of concentrations downwind of elongated buildings. The National Exposure Research Laboratory (NERL) Computational Exposur

Characterization of pollutant dispersion near elongated buildings based on wind tunnel simulations

NASA Astrophysics Data System (ADS)

Perry, S. G.; Heist, D. K.; Brouwer, L. H.; Monbureau, E. M.; Brixey, L. A.

2016-10-01

This paper presents a wind tunnel study of the effects of elongated rectangular buildings on the dispersion of pollutants from nearby stacks. The study examines the influence of source location, building aspect ratio, and wind direction on pollutant dispersion with the goal of developing improved algorithms within dispersion models. The paper also examines the current AERMOD/PRIME modeling capabilities compared to wind tunnel observations. Differences in the amount of plume material entrained in the wake region downwind of a building for various source locations and source heights are illustrated with vertical and lateral concentration profiles. These profiles were parameterized using the Gaussian equation and show the influence of building/source configurations on those parameters. When the building is oriented at 45° to the approach flow, for example, the effective plume height descends more rapidly than it does for a perpendicular building, enhancing the resulting surface concentrations in the wake region. Buildings at angles to the wind cause a cross-wind shift in the location of the plume resulting from a lateral mean flow established in the building wake. These and other effects that are not well represented in many dispersion models are important considerations when developing improved algorithms to estimate the location and magnitude of concentrations downwind of elongated buildings.

Turbulent dispersivity under conditions relevant to airborne disease transmission between laboratory animals

NASA Astrophysics Data System (ADS)

Halloran, Siobhan; Ristenpart, William

2013-11-01

Virologists and other researchers who test pathogens for airborne disease transmissibility often place a test animal downstream from an inoculated animal and later determine whether the test animal became infected. Despite the crucial role of the airflow in pathogen transmission between the animals, to date the infectious disease community has paid little attention to the effect of airspeed or turbulent intensity on the probability of transmission. Here we present measurements of the turbulent dispersivity under conditions relevant to experimental tests of airborne disease transmissibility between laboratory animals. We used time lapse photography to visualize the downstream transport and turbulent dispersion of smoke particulates released from a point source downstream of an axial fan, thus mimicking the release and transport of expiratory aerosols exhaled by an inoculated animal. We show that for fan-generated turbulence the plume width is invariant with the mean airspeed and, close to the point source, increases linearly with downstream position. Importantly, the turbulent dispersivity is insensitive to the presence of meshes placed downstream from the point source, indicating that the fan length scale dictates the turbulent intensity and corresponding dispersivity.

Energy allocation during the maturation of adults in a long-lived insect: implications for dispersal and reproduction.

PubMed

David, G; Giffard, B; van Halder, I; Piou, D; Jactel, H

2015-10-01

Energy allocation strategies have been widely documented in insects and were formalized in the context of the reproduction process by the terms 'capital breeder' and 'income breeder'. We propose here the extension of this framework to dispersal ability, with the concepts of 'capital disperser' and 'income disperser', and explore the trade-off in resource allocation between dispersal and reproduction. We hypothesized that flight capacity was sex-dependent, due to a trade-off in energy allocation between dispersal and egg production in females. We used Monochamus galloprovincialis as model organism, a long-lived beetle which is the European vector of the pine wood nematode. We estimated the flight capacity with a flight mill and used the number of mature eggs as a proxy for the investment in reproduction. We used the ratio between dry weights of the thorax and the abdomen to investigate the trade-off. The probability of flying increased with the adult weight at emergence, but was not dependent on insect age or sex. Flight distance increased with age in individuals but did not differ between sexes. It was also positively associated with energy allocation to thorax reserves, which increased with age. In females, the abdomen weight and the number of eggs also increase with age with no negative effect on flight capacity, indicating a lack of trade-off. This long-lived beetle has a complex strategy of energy allocation, being a 'capital disperser' in terms of flight ability, an 'income disperser' in terms of flight performance and an 'income breeder' in terms of egg production.

An alternative screening model for the estimation of outdoor air concentration at large contaminated sites

NASA Astrophysics Data System (ADS)

Verginelli, Iason; Nocentini, Massimo; Baciocchi, Renato

2017-09-01

Simplified analytical solutions of fate and transport models are often used to carry out risk assessment on contaminated sites, to evaluate the long-term air quality in relation to volatile organic compounds in either soil or groundwater. Among the different assumptions employed to develop these solutions, in this work we focus on those used in the ASTM-RBCA ;box model; for the evaluation of contaminant dispersion in the atmosphere. In this simple model, it is assumed that the contaminant volatilized from the subsurface is dispersed in the atmosphere within a mixing height equal to two meters, i.e. the height of the breathing zone. In certain cases, this simplification could lead to an overestimation of the outdoor air concentration at the point of exposure. In this paper we first discuss the maximum source lengths (in the wind direction) for which the application of the ;box model; can be considered acceptable. Specifically, by comparing the results of ;box model; with the SCREEN3 model of U.S.EPA we found that under very stable atmospheric conditions (class F) the ASTM-RBCA approach provides acceptable results for source lengths up to 200 m while for very unstable atmospheric conditions (class A and B) the overestimation of the concentrations at the point of the exposure can be already observed for source lengths of only 10 m. In the latter case, the overestimation of the ;box model; can be of more than one order of magnitude for source lengths above 500 m. To overcome this limitation, in this paper we introduce a simple analytical solution that can be used for the calculation of the concentration at the point of exposure for large contaminated sites. The method consists in the introduction of an equivalent mixing zone height that allows to account for the dispersion of the contaminants along the source length while keeping the simplistic ;box model; approach that is implemented in most of risk assessment tools that are based on the ASTM-RBCA standard (e.g. RBCA toolkit). Based on our testing, we found that the developed model replicates very well the results of the more sophisticated dispersion SCREEN3 model with deviations always below 10%. The key advantage of this approach is that it can be very easily incorporated in the current risk assessment screening tools that are based on the ASTM standards while ensuring a more accurate evaluation of the concentration at the point of exposure.

Fast and wide tuning wavelength-swept source based on dispersion-tuned fiber optical parametric oscillator.

PubMed

Zhou, Yue; Cheung, Kim K Y; Li, Qin; Yang, Sigang; Chui, P C; Wong, Kenneth K Y

2010-07-15

We demonstrate a dispersion-tuned fiber optical parametric oscillator (FOPO)-based swept source with a sweep rate of 40 kHz and a wavelength tuning range of 109 nm around 1550 nm. The cumulative speed exceeds 4,000,000 nm/s. The FOPO is pumped by a sinusoidally modulated pump, which is driven by a clock sweeping linearly from 1 to 1.0006 GHz. A spool of dispersion-compensating fiber is added inside the cavity to perform dispersion tuning. The instantaneous linewidth is 0.8 nm without the use of any wavelength selective element inside the cavity. 1 GHz pulses with pulse width of 150 ps are generated.

Impact of Acoustic Radiation Force Excitation Geometry on Shear Wave Dispersion and Attenuation Estimates.

PubMed

Lipman, Samantha L; Rouze, Ned C; Palmeri, Mark L; Nightingale, Kathryn R

2018-04-01

Shear wave elasticity imaging (SWEI) characterizes the mechanical properties of human tissues to differentiate healthy from diseased tissue. Commercial scanners tend to reconstruct shear wave speeds for a region of interest using time-of-flight methods reporting a single shear wave speed (or elastic modulus) to the end user under the assumptions that tissue is elastic and shear wave speeds are not dependent on the frequency content of the shear waves. Human tissues, however, are known to be viscoelastic, resulting in dispersion and attenuation. Shear wave spectroscopy and spectral methods have been previously reported in the literature to quantify shear wave dispersion and attenuation, commonly making an assumption that the acoustic radiation force excitation acts as a cylindrical source with a known geometric shear wave amplitude decay. This work quantifies the bias in shear dispersion and attenuation estimates associated with making this cylindrical wave assumption when applied to shear wave sources with finite depth extents, as commonly occurs with realistic focal geometries, in elastic and viscoelastic media. Bias is quantified using analytically derived shear wave data and shear wave data generated using finite-element method models. Shear wave dispersion and attenuation bias (up to 15% for dispersion and 41% for attenuation) is greater for more tightly focused acoustic radiation force sources with smaller depths of field relative to their lateral extent (height-to-width ratios <16). Dispersion and attenuation errors associated with assuming a cylindrical geometric shear wave decay in SWEI can be appreciable and should be considered when analyzing the viscoelastic properties of tissues with acoustic radiation force source distributions with limited depths of field. Copyright © 2018 World Federation for Ultrasound in Medicine and Biology. Published by Elsevier Inc. All rights reserved.

Tsunami Focusing and Leading Amplitude

NASA Astrophysics Data System (ADS)

Kanoglu, U.

2016-12-01

Tsunamis transform substantially through spatial and temporal spreading from their source region. This substantial spreading might result unique maximum tsunami wave heights which might be attributed to the source configuration, directivity, the waveguide structures of mid-ocean ridges and continental shelves, focusing and defocusing through submarine seamounts, random focusing due to small changes in bathymetry, dispersion, and, most likely, combination of some of these effects. In terms of the maximum tsunami wave height, after Okal and Synolakis (2016 Geophys. J. Int. 204, 719-735), it is clear that dispersion would be one of the reasons to drive the leading wave amplitude in a tsunami wave train. Okal and Synolakis (2016), referring to this phenomenon as sequencing -later waves in the train becoming higher than the leading one, considered Hammack's (1972, Ph.D. Dissertation, Calif. Inst. Tech., 261 pp) formalism, in addition to LeMéhauté and Wang's (1995 Water waves generated by underwater explosion, World Scientific, 367 pp), to evaluate linear dispersive tsunami propagation from a circular plug uplifted on an ocean of constant depth. They identified transition distance, as the second wave being larger, performing parametric study for the radius of the plug and the depth of the ocean. Here, we extend Okal and Synolakis' (2016) analysis to an initial wave field with a finite crest length and, in addition, to a most common tsunami initial wave form of N-wave (Tadepalli and Synolakis, 1994 Proc. R. Soc. A: Math. Phys. Eng. Sci. 445, 99-112). First, we investigate the focusing feature in the leading-depression side, which enhance tsunami wave height as presented by Kanoglu et al. (2013 Proc. R. Soc. A: Math. Phys. Eng. Sci. 469, 20130015). We then discuss the results in terms of leading wave amplitude presenting a parametric study and identify a simple relation for the transition distance. The solution presented here could be used to better analyze dispersive characteristics of shallow water-wave numerical models and for benchmarking, in addition to the benchmark problems in Synolakis et al. (2008 Pure Appl. Geophys. 165(11-12), 2197-2228). This study received funding from project ASTARTE-Assessment Strategy and Risk Reduction for Tsunamis in Europe, a collaborative project Grant 603839, FP7-ENV2013 6.4-3.

Turbulent Plume Dispersion over Two-dimensional Idealized Urban Street Canyons

NASA Astrophysics Data System (ADS)

Wong, C. C. C.; Liu, C. H.

2012-04-01

Human activities are the primary pollutant sources which degrade the living quality in the current era of dense and compact cities. A simple and reasonably accurate pollutant dispersion model is helpful to reduce pollutant concentrations in city or neighborhood scales by refining architectural design or urban planning. The conventional method to estimate the pollutant concentration from point/line sources is the Gaussian plume model using empirical dispersion coefficients. Its accuracy is pretty well for applying to rural areas. However, the dispersion coefficients only account for the atmospheric stability and streamwise distance that often overlook the roughness of urban surfaces. Large-scale buildings erected in urban areas significantly modify the surface roughness that in turn affects the pollutant transport in the urban canopy layer (UCL). We hypothesize that the aerodynamic resistance is another factor governing the dispersion coefficient in the UCL. This study is thus conceived to study the effects of urban roughness on pollutant dispersion coefficients and the plume behaviors. Large-eddy simulations (LESs) are carried out to examine the plume dispersion from a ground-level pollutant source over idealized 2D street canyons in neutral stratification. Computations with a wide range of aspect ratios (ARs), including skimming flow to isolated flow regimes, are conducted. The vertical profiles of pollutant distribution for different values of friction factor are compared that all reach a self-similar Gaussian shape. Preliminary results show that the pollutant dispersion is closely related to the friction factor. For relatively small roughness, the factors of dispersion coefficient vary linearly with the friction factor until the roughness is over a certain level. When the friction factor is large, its effect on the dispersion coefficient is less significant. Since the linear region covers at least one-third of the full range of friction factor in our empirical analysis, urban roughness is a major factor for dispersion coefficient. The downstream air quality could then be a function of both atmospheric stability and urban roughness.

Medical Subject Headings (MeSH) for indexing and retrieving open-source healthcare data.

PubMed

Marc, David T; Khairat, Saif S

2014-01-01

The US federal government initiated the Open Government Directive where federal agencies are required to publish high value datasets so that they are available to the public. Data.gov and the community site Healthdata.gov were initiated to disperse such datasets. However, data searches and retrieval for these sites are keyword driven and severely limited in performance. The purpose of this paper is to address the issue of extracting relevant open-source data by proposing a method of adopting the MeSH framework for indexing and data retrieval. A pilot study was conducted to compare the performance of traditional keywords to MeSH terms for retrieving relevant open-source datasets related to "mortality". The MeSH framework resulted in greater sensitivity with comparable specificity to the keyword search. MeSH showed promise as a method for indexing and retrieving data, yet future research should conduct a larger scale evaluation of the performance of the MeSH framework for retrieving relevant open-source healthcare datasets.

Subcarrier multiplexing tolerant dispersion transmission system employing optical broadband sources.

PubMed

Grassi, Fulvio; Mora, José; Ortega, Beatriz; Capmany, José

2009-03-16

This paper presents a novel SCM optical transmission system for next-generation WDM-PONs combining broadband optical sources and a Mach-Zehnder interferometric structure. The approach leeds to transport RF signals up to 50 GHz being compatible with RoF systems since a second configuration has been proposed in order to overcome dispersion carrier suppression effect using DSB modulation. The theoretical analysis validates the potentiality of the system also considering the effects of the dispersion slope over the transmission window. (c) 2009 Optical Society of America

Development a computer codes to couple PWR-GALE output and PC-CREAM input

NASA Astrophysics Data System (ADS)

Kuntjoro, S.; Budi Setiawan, M.; Nursinta Adi, W.; Deswandri; Sunaryo, G. R.

2018-02-01

Radionuclide dispersion analysis is part of an important reactor safety analysis. From the analysis it can be obtained the amount of doses received by radiation workers and communities around nuclear reactor. The radionuclide dispersion analysis under normal operating conditions is carried out using the PC-CREAM code, and it requires input data such as source term and population distribution. Input data is derived from the output of another program that is PWR-GALE and written Population Distribution data in certain format. Compiling inputs for PC-CREAM programs manually requires high accuracy, as it involves large amounts of data in certain formats and often errors in compiling inputs manually. To minimize errors in input generation, than it is make coupling program for PWR-GALE and PC-CREAM programs and a program for writing population distribution according to the PC-CREAM input format. This work was conducted to create the coupling programming between PWR-GALE output and PC-CREAM input and programming to written population data in the required formats. Programming is done by using Python programming language which has advantages of multiplatform, object-oriented and interactive. The result of this work is software for coupling data of source term and written population distribution data. So that input to PC-CREAM program can be done easily and avoid formatting errors. Programming sourceterm coupling program PWR-GALE and PC-CREAM is completed, so that the creation of PC-CREAM inputs in souceterm and distribution data can be done easily and according to the desired format.

Dispersal of Salmonella Typhimurium by rain splash onto tomato plants.

PubMed

Cevallos-Cevallos, Juan M; Danyluk, Michelle D; Gu, Ganyu; Vallad, Gary E; van Bruggen, Ariena H C

2012-03-01

Outbreaks of Salmonella enterica have increasingly been associated with tomatoes and traced back to production areas, but the spread of Salmonella from a point source onto plants has not been described. Splash dispersal by rain could be one means of dissemination. Green fluorescent protein-labeled, kanamycin-resistant Salmonella enterica sv. Typhimurium dispensed on the surface of plastic mulch, organic mulch, or soil at 10⁸ CFU/cm² was used as the point source in the center of a rain simulator. Tomato plants in soil with and without plastic or organic mulch were placed around the point source, and rain intensities of 60 and 110 mm/h were applied for 5, 10, 20, and 30 min. Dispersal of Salmonella followed a negative exponential model with a half distance of 3 cm at 110 mm/h. Dispersed Salmonella survived for 3 days on tomato leaflets, with a total decline of 5 log and an initial decimal reduction time of 10 h. Recovery of dispersed Salmonella from plants at the maximum observed distance ranged from 3 CFU/g of leaflet after a rain episode of 110 mm/h for 10 min on soil to 117 CFU/g of leaflet on plastic mulch. Dispersal of Salmonella on plants with and without mulch was significantly enhanced by increasing rain duration from 0 to 10 min, but dispersal was reduced when rainfall duration increased from 10 to 30 min. Salmonella may be dispersed by rain to contaminate tomato plants in the field, especially during rain events of 10 min and when plastic mulch is used.

DNA Fingerprinting Validates Seed Dispersal Curves from Observational Studies in the Neotropical Legume Parkia

PubMed Central

Heymann, Eckhard W.; Lüttmann, Kathrin; Michalczyk, Inga M.; Saboya, Pedro Pablo Pinedo; Ziegenhagen, Birgit; Bialozyt, Ronald

2012-01-01

Background Determining the distances over which seeds are dispersed is a crucial component for examining spatial patterns of seed dispersal and their consequences for plant reproductive success and population structure. However, following the fate of individual seeds after removal from the source tree till deposition at a distant place is generally extremely difficult. Here we provide a comparison of observationally and genetically determined seed dispersal distances and dispersal curves in a Neotropical animal-plant system. Methodology/Principal Findings In a field study on the dispersal of seeds of three Parkia (Fabaceae) species by two Neotropical primate species, Saguinus fuscicollis and Saguinus mystax, in Peruvian Amazonia, we observationally determined dispersal distances. These dispersal distances were then validated through DNA fingerprinting, by matching DNA from the maternally derived seed coat to DNA from potential source trees. We found that dispersal distances are strongly right-skewed, and that distributions obtained through observational and genetic methods and fitted distributions do not differ significantly from each other. Conclusions/Significance Our study showed that seed dispersal distances can be reliably estimated through observational methods when a strict criterion for inclusion of seeds is observed. Furthermore, dispersal distances produced by the two primate species indicated that these primates fulfil one of the criteria for efficient seed dispersers. Finally, our study demonstrated that DNA extraction methods so far employed for temperate plant species can be successfully used for hard-seeded tropical plants. PMID:22514748

Short-Term Rhizosphere Effect on Available Carbon Sources, Phenanthrene Degradation, and Active Microbiome in an Aged-Contaminated Industrial Soil

PubMed Central

Thomas, François; Cébron, Aurélie

2016-01-01

Over the last decades, understanding of the effects of plants on soil microbiomes has greatly advanced. However, knowledge on the assembly of rhizospheric communities in aged-contaminated industrial soils is still limited, especially with regard to transcriptionally active microbiomes and their link to the quality or quantity of carbon sources. We compared the short-term (2–10 days) dynamics of bacterial communities and potential PAH-degrading bacteria in bare or ryegrass-planted aged-contaminated soil spiked with phenanthrene, put in relation with dissolved organic carbon (DOC) sources and polycyclic aromatic hydrocarbon (PAH) pollution. Both resident and active bacterial communities (analyzed from DNA and RNA, respectively) showed higher species richness and smaller dispersion between replicates in planted soils. Root development strongly favored the activity of Pseudomonadales within the first 2 days, and of members of Actinobacteria, Caulobacterales, Rhizobiales, and Xanthomonadales within 6–10 days. Plants slowed down the dissipation of phenanthrene, while root exudation provided a cocktail of labile substrates that might preferentially fuel microbial growth. Although the abundance of PAH-degrading genes increased in planted soil, their transcription level stayed similar to bare soil. In addition, network analysis revealed that plants induced an early shift in the identity of potential phenanthrene degraders, which might influence PAH dissipation on the long-term. PMID:26903971

Long-distance plant dispersal to North Atlantic islands: colonization routes and founder effect.

PubMed

Alsos, Inger Greve; Ehrich, Dorothee; Eidesen, Pernille Bronken; Solstad, Heidi; Westergaard, Kristine Bakke; Schönswetter, Peter; Tribsch, Andreas; Birkeland, Siri; Elven, Reidar; Brochmann, Christian

2015-04-15

Long-distance dispersal (LDD) processes influence the founder effect on islands. We use genetic data for 25 Atlantic species and similarities among regional floras to analyse colonization, and test whether the genetic founder effect on five islands is associated with dispersal distance, island size and species traits. Most species colonized postglacially via multiple dispersal events from several source regions situated 280 to >3000 km away, and often not from the closest ones. A strong founder effect was observed for insect-pollinated mixed maters, and it increased with dispersal distance and decreased with island size in accordance with the theory of island biogeography. Only a minor founder effect was observed for wind-pollinated outcrossing species. Colonization patterns were largely congruent, indicating that despite the importance of stochasticity, LDD is mainly determined by common factors, probably dispersal vectors. Our findings caution against a priori assuming a single, close source region in biogeographic analyses. Published by Oxford University Press on behalf of the Annals of Botany Company.

Modeling atmospheric effects - an assessment of the problems

Treesearch

Douglas G. Fox

1976-01-01

Our ability to simulate atmospheric processes that affect the life cycle of pollution is reviewed. The transport process is considered on three scales (a) the near-source or single-plume dispersion problem, (b) the multiple-source dispersion problem, and (c) the long-range transport. Modeling the first of these is shown to be well within the capability of generally...

Chandra Observations of Low Velocity Dispersion Groups

NASA Astrophysics Data System (ADS)

Helsdon, Stephen F.; Ponman, Trevor J.; Mulchaey, J. S.

2005-01-01

Deviations of galaxy groups from cluster scaling relations can be understood in terms of an excess of entropy in groups. The main effect of this excess is to reduce the density and thus the luminosity of the intragroup gas. Given this, groups should also show a steep relationship between X-ray luminosity and velocity dispersion. However, previous work suggests that this is not the case, with many measuring slopes flatter than the cluster relation. Examining the group LX-σ relation shows that much of the flattening is caused by a small subset of groups that show very high X-ray luminosities for their velocity dispersions (or vice versa). Detailed Chandra study of two such groups shows that earlier ROSAT results were subject to significant (~30%-40%) point-source contamination but confirm that a significant hot intergalactic medium is present in these groups, although these are two of the coolest systems in which intergalactic X-ray emission has been detected. Their X-ray properties are shown to be broadly consistent with those of other galaxy groups, although the gas entropy in NGC 1587 is unusually low, and its X-ray luminosity is correspondingly high for its temperature when compared with most groups. This leads us to suggest that the velocity dispersion in these systems has been reduced in some way, and we consider how this might have come about.

Simulation of Turbulent Combustion Fields of Shock-Dispersed Aluminum Using the AMR Code

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kuhl, A L; Bell, J B; Beckner, V E

2006-11-02

We present a Model for simulating experiments of combustion in Shock-Dispersed-Fuel (SDF) explosions. The SDF charge consisted of a 0.5-g spherical PETN booster, surrounded by 1-g of fuel powder (flake Aluminum). Detonation of the booster charge creates a high-temperature, high-pressure source (PETN detonation products gases) that both disperses the fuel and heats it. Combustion ensues when the fuel mixes with air. The gas phase is governed by the gas-dynamic conservation laws, while the particle phase obeys the continuum mechanics laws for heterogeneous media. The two phases exchange mass, momentum and energy according to inter-phase interaction terms. The kinetics model usedmore » an empirical particle burn relation. The thermodynamic model considers the air, fuel and booster products to be of frozen composition, while the Al combustion products are assumed to be in equilibrium. The thermodynamic states were calculated by the Cheetah code; resulting state points were fit with analytic functions suitable for numerical simulations. Numerical simulations of combustion of an Aluminum SDF charge in a 6.4-liter chamber were performed. Computed pressure histories agree with measurements.« less

Analytical possibilities of different X-ray fluorescence systems for determination of trace elements in aqueous samples pre-concentrated with carbon nanotubes

NASA Astrophysics Data System (ADS)

Marguí, E.; Zawisza, B.; Skorek, R.; Theato, T.; Queralt, I.; Hidalgo, M.; Sitko, R.

2013-10-01

This study was aimed to achieve improved instrumental sensitivity and detection limits for multielement determination of V, Cr, Mn, Fe, Co, Ni, Cu, Zn, Ga, Se, Pb and Cd in liquid samples by using different X-ray fluorescence (XRF) configurations (a benchtop energy-dispersive X-ray fluorescence spectrometer, a benchtop polarised energy-dispersive X-ray fluorescence spectrometer and a wavelength-dispersive X-ray fluorescence spectrometer). The preconcentration of metals from liquid solutions consisted on a solid-phase extraction using carbon nanotubes (CNTs) as solid sorbents. After the extraction step, the aqueous sample was filtered and CNTs with the absorbed elements were collected onto a filter paper which was directly analyzed by XRF. The calculated detection limits in all cases were in the low ng mL- 1 range. Nevertheless, results obtained indicate the benefits, in terms of sensitivity, of using polarized X-ray sources using different secondary targets in comparison to conventional XRF systems, above all if Cd determination is required. The developed methodologies, using the aforementioned equipments, have been applied for multielement determination in water samples from an industrial area of Poland.

A numerical study of air pollutant dispersion with bimolecular chemical reactions in an urban street canyon using large-eddy simulation

NASA Astrophysics Data System (ADS)

Kikumoto, Hideki; Ooka, Ryozo

2012-07-01

A large-eddy simulation is performed on a turbulent dispersion of chemically reactive air pollutants in a two-dimensional urban street canyon with an aspect ratio of 1.0. Nitrogen monoxide emitted from a line-source set on the bottom of the street canyon disperses and reacts with Ozone included in a free stream. The reactions have significant influences on the concentrations of pollutants in the canyon space, and they increase the concentrations of the reaction products relative to of the concentrations of the reactants. The transport of air pollutants through a free shear layer above the canyon is closely related to the structure of the turbulence. Gases in the canyon are mainly exhausted when low-speed regions appear above the canyon. In contrast, pollutants in the free stream flow into the canyon with high-speed fluid bodies. Consequently, the correlation between the time fluctuations of the reactants' concentrations strongly affects the reaction rates in the region near the free shear layer. In this calculation, the correlation term reaches to a value of 20% of the mean reaction rate at a maximum there.

Explosive particle soil surface dispersion model for detonated military munitions.

PubMed

Hathaway, John E; Rishel, Jeremy P; Walsh, Marianne E; Walsh, Michael R; Taylor, Susan

2015-07-01

The accumulation of high explosive mass residue from the detonation of military munitions on training ranges is of environmental concern because of its potential to contaminate the soil, surface water, and groundwater. The US Department of Defense wants to quantify, understand, and remediate high explosive mass residue loadings that might be observed on active firing ranges. Previously, efforts using various sampling methods and techniques have resulted in limited success, due in part to the complicated dispersion pattern of the explosive particle residues upon detonation. In our efforts to simulate particle dispersal for high- and low-order explosions on hypothetical firing ranges, we use experimental particle data from detonations of munitions from a 155-mm howitzer, which are common military munitions. The mass loadings resulting from these simulations provide a previously unattained level of detail to quantify the explosive residue source-term for use in soil and water transport models. In addition, the resulting particle placements can be used to test, validate, and optimize particle sampling methods and statistical models as applied to firing ranges. Although the presented results are for a hypothetical 155-mm howitzer firing range, the method can be used for other munition types once the explosive particle characteristics are known.

Optical remote sensing to quantify fugitive particulate mass emissions from stationary short-term and mobile continuous sources: part II. Field applications.

PubMed

Du, Ke; Yuen, Wangki; Wang, Wei; Rood, Mark J; Varma, Ravi M; Hashmonay, Ram A; Kim, Byung J; Kemme, Michael R

2011-01-15

Quantification of emissions of fugitive particulate matter (PM) into the atmosphere from military training operations is of interest by the United States Department of Defense. A new range-resolved optical remote sensing (ORS) method was developed to quantify fugitive PM emissions from puff sources (i.e., artillery back blasts), ground-level mobile sources (i.e., movement of tracked vehicles), and elevated mobile sources (i.e., airborne helicopters) in desert areas that are prone to generating fugitive dust plumes. Real-time, in situ mass concentration profiles for PM mass with particle diameters <10 μm (PM(10)) and <2.5 μm (PM(2.5)) were obtained across the dust plumes that were generated by these activities with this new method. Back blasts caused during artillery firing were characterized as a stationary short-term puff source whose plumes typically dispersed to <10 m above the ground with durations of 10-30 s. Fugitive PM emissions caused by artillery back blasts were related to the zone charge and ranged from 51 to 463 g PM/firing for PM(10) and 9 to 176 g PM/firing for PM(2.5). Movement of tracked vehicles and flying helicopters was characterized as mobile continuous sources whose plumes typically dispersed 30-50 m above the ground with durations of 100-200 s. Fugitive PM emissions caused by moving tracked vehicles ranged from 8.3 to 72.5 kg PM/km for PM(10) and 1.1 to 17.2 kg PM/km for PM(2.5), and there was no obvious correlation between PM emission and vehicle speed. The emission factor for the helicopter flying at 3 m above the ground ranged from 14.5 to 114.1 kg PM/km for PM(10) and 5.0 to 39.5 kg PM/km for PM(2.5), depending on the velocity of the helicopter and type of soil it flies over. Fugitive PM emissions by an airborne helicopter were correlated with helicopter speed for a particular soil type. The results from this range-resolved ORS method were also compared with the data obtained with another path-integrated ORS method and a Flux Tower method.

A closed-form expression for the effect in breakthrough curves of biofilm development: enhanced dispersion

NASA Astrophysics Data System (ADS)

Sanchez-Vila, X.; Rodriguez-Escales, P.

2017-12-01

It has been widely reported that biofilm growth changes the hydraulic parameters in porous media. While the impact upon reduction of hydraulic conductivity has been widely explained and modeled, this has not been the case for the reported order(s) of magnitude increase in dispersion coefficient even when a minute percentage of biofilm is formed, and despite the effect of biofilm growth is to reduce specific discharge, producing a somewhat counterintuitive result. We develop here a simple yet practical expression for the evaluation of an effective dispersion coefficient caused by biomass colonization, based on the modification of the breakthrough curves (in terms of temporal moments) with respect to the biofilm-free porous media. The advantage of the expression is that it is written in terms of observables that are relatively easy to measure in the lab or the field, contrarily to existing expressions that relate the effect to channelization resulting in tortuosity being the driving term of effective dispersion. We have tested our simplified expression in a number of reported sites, where enhanced dispersion of 1-2 orders of magnitude has been reported, indirectly showing the relative importance of the terms included in the expression.

Resolution enhancement of partial coherence interferometry by dispersion compensation

NASA Astrophysics Data System (ADS)

Baumgartner, Angela; Hitzenberger, Christoph K.; Drexler, Wolfgang; Fercher, Adolf F.

1997-12-01

In the past ten years partial coherence interferometry and optical coherence tomography have been developed for high precision biometry and tomography of the human eye in vivo. The longitudinal resolution of the optical coherence tomography technique depends on the spectral bandwidth of the light source used and on the dispersion of the media to be measured. In nondispersive media the resolution is approximately equal to the coherence length of the light used, which is inversely proportional to the width of the emission spectrum. Hence, a broad emission spectrum yields a short coherence length and consequently a good resolution. However, if the tissue under investigation is dispersive, the coherence envelope of the signal broadens leading to a decrease in resolution and interference fringe contrast. This effect becomes predominant if measurements through the dispersive media of the eye to the retina are performed with source bandwidths larger than approximately 25 nm. In order to achieve optimum resolution of OCT by applying a light source with a broad emission spectrum, the dispersion of the object to be measured, i.e. in this case of the ocular media, has to be compensated. Within the scope of this work we demonstrate the resolution improvement that is obtained by compensating the dispersive effects of the ocular media and using broadband light sources. Furthermore, we present the first optical coherence tomogram recorded with this technique in the retina of a human eye in vivo with an axial geometrical resolution of approximately 6 micrometers which is a two-fold improvement compared to presently used technology.

Laser control of natural disperse systems

NASA Astrophysics Data System (ADS)

Vlasova, Olga L.; Bezrukova, Alexandra G.

2003-10-01

Different water disperse systems were studied by integral (spectroturbidemetry) and differential light scattering method with a laser as a source of light. The investigation done concerns the state of kaolin dispersions at storage and under dilution as an example of mineral dispersion systems such as natural water. The role of some light scattering parameters for an optical analysis of water dispersions, like the dispersion of erythrocytes and bacterial cells -Escherichia coli is discussed. The results obtained can help to elaborate the methods for on-line optical control fo natural disperse systems (water, air) with mineral and biological particles.

Tracer dispersion experiments carried out in London during 2003 and 2004 as part of the DAPPLE project

NASA Astrophysics Data System (ADS)

Martin, D.; Shallcross, D.; Nickless, G.; White, I.

2005-12-01

Transport, dispersion and ultimate fate of pollutants has very important implications for the environment at the urban, regional and global scales. Localised emissions of both man-made and naturally produced pollutants can both directly and indirectly impact the health of the inhabitants. The DAPPLE (Dispersion of Air Pollutants and their Penetration into the Local Environment) consortium consists of six universities, which comprises of a multidisciplinary approach to study relatively small-scale urban atmospheric dispersion. Wind tunnel modelling studies, computer fluid dynamical simulations, fieldwork studies using tracers and dispersion modelling were all carried out in an attempt to achieve this. In this paper we report on tracer dispersion experiments carried out in May 2003 and June 2004. These involve the release of various perfluorocarbon (PFC) tracers centred on Marylebone Road in London. These compounds are inert, non-reactive and have a very low atmospheric background concentration with little variability. These properties make them the ideal atmospheric tracer and this combined with an ultra sensitive analytical technique (sample pre-concentration on carbon based adsorbents followed with detection by Negative Ion Chemical Ionization Mass Spectrometry) makes very small release amounts feasible. The source-receptor relationship is studied for various source and receptor positions and distances. Source receptor relationships for both rooftop and indoor positions were evaluated as part of the project. Results of concurrent meteorological measurements are also presented as well as comparison with a number of simple dispersion models.

Many-body dispersion interactions from the exchange-hole dipole moment model

NASA Astrophysics Data System (ADS)

Otero-de-la-Roza, A.; Johnson, Erin R.

2013-02-01

In this article, we present the extension of the exchange-hole dipole moment model (XDM) of dispersion interactions to the calculation of two-body and three-body dispersion energy terms to any order, 2l-pole oscillator strengths, and polarizabilities. By using the newly-formulated coefficients, we study the relative importance of the higher-order two-body and the leading non-additive three-body (triple-dipole) interactions in gas-phase as well as in condensed systems. We show that the two-body terms up to R-10, but not the terms of higher-order, are essential in the correct description of the dispersion energy, while there are a number of difficulties related to the choice of the damping function, which precludes the use three-body triple-dipole contributions in XDM. We conclude that further study is required before the three-body term can be used in production XDM density-functional calculations and point out the salient problems regarding its use.

RLINE: Re-formulation of Plume Spread for Near-Surface Dispersion

EPA Science Inventory

Recent concerns about effects of automobile emissions on the health of people living close to roads have motivated an examination of models to estimate dispersion in the surface boundary layer. During the development of a new line source dispersion model, RLINE (Snyder et al., 20...

Compact solid source of hydrogen gas

DOEpatents

Kravitz, Stanley H.; Hecht, Andrew M.; Sylwester, Alan P.; Bell, Nelson S.

2004-06-08

A compact solid source of hydrogen gas, where the gas is generated by contacting water with micro-disperse particles of sodium borohydride in the presence of a catalyst, such as cobalt or ruthenium. The micro-disperse particles can have a substantially uniform diameter of 1-10 microns, and preferably about 3-5 microns. Ruthenium or cobalt catalytic nanoparticles can be incorporated in the micro-disperse particles of sodium borohydride, which allows a rapid and complete reaction to occur without the problems associated with caking and scaling of the surface by the reactant product sodium metaborate. A closed loop water management system can be used to recycle wastewater from a PEM fuel cell to supply water for reacting with the micro-disperse particles of sodium borohydride in a compact hydrogen gas generator. Capillary forces can wick water from a water reservoir into a packed bed of micro-disperse fuel particles, eliminating the need for using an active pump.

Determination of the chromatic dispersion of liquids based on the liquid-prism SPR configuration in angular and spectral interrogations

NASA Astrophysics Data System (ADS)

Lan, Guoqiang; Liu, Shugang; Wang, Yuxiao; Zhang, Xueru; Song, Yinglin

2015-10-01

In this work, we use the liquid-prism SPR sensing configuration to determine the chromatic dispersion of different liquids, since the condition of SPR is sensitive to the refractive index of the liquid prism. We use the glass slide coated with 50 nm Au film as the sensing chip, and use AvaLight - HAL (360 nm - 2500 nm) light source as the broaden band light source in our experiments. We adopt the deionized water as the standard sample to determine the chromatic dispersion of different liquid samples (ethanol and n-hexane), and we implement the experiment through the SPR sensing configuration in angular and spectral interrogations. According to the experimental data, the chromatic dispersions of ethanol and n-hexane are obtained. The proposed technique provides a new high sensitive method for the determination of chromatic dispersion of liquids.

Characterizing the detectability of emission signals from a North Korean nuclear detonation

DOE PAGES

Werth, David; Buckley, Robert

2017-02-01

Here, the detectability of emission sources, defined by a low-level of mixing with other sources, was estimated for various locations surrounding the Sea of Japan, including a site within North Korea. A high-resolution meteorological model coupled to a dispersion model was used to simulate plume dynamics for four periods, and two metrics of airborne plume mixing were calculated for each source. While emissions from several known sources in this area tended to blend with others while dispersing downwind, the North Korean plume often remained relatively distinct, thereby making it potentially easier to unambiguously ‘backtrack’ it to its source.

Drastic reduction in the growth temperature of graphene on copper via enhanced London dispersion force

PubMed Central

Choi, Jin-Ho; Li, Zhancheng; Cui, Ping; Fan, Xiaodong; Zhang, Hui; Zeng, Changgan; Zhang, Zhenyu

2013-01-01

London dispersion force is ubiquitous in nature, and is increasingly recognized to be an important factor in a variety of surface processes. Here we demonstrate unambiguously the decisive role of London dispersion force in non-equilibrium growth of ordered nanostructures on metal substrates using aromatic source molecules. Our first-principles based multi-scale modeling shows that a drastic reduction in the growth temperature, from ~1000°C to ~300°C, can be achieved in graphene growth on Cu(111) when the typical carbon source of methane is replaced by benzene or p-Terphenyl. The London dispersion force enhances their adsorption energies by about (0.5–1.8) eV, thereby preventing their easy desorption, facilitating dehydrogenation, and promoting graphene growth at much lower temperatures. These quantitative predictions are validated in our experimental tests, showing convincing demonstration of monolayer graphene growth using the p-Terphenyl source. The general trends established are also more broadly applicable in molecular synthesis of surface-based nanostructures. PMID:23722566

Effects of Source Correlations on the Spectrum of Radiated Fields

DTIC Science & Technology

1990-09-01

media. When the refractive index n(co) is nearly constant over the source spectral width, the medium acts as a non- dispersive homogeneous medium of...constant refractive index no = n(w0 ), where o is the central frequency of the source spectrum. We will consider the non- dispersive case first. It is...in free space (a), for propagation in a homogeneous medium of an index of refraction n((o) = 1.5 (b) and for propagation in a medium of index of

Characterization of pollutant dispersion near elongated buildings based on wind tunnel simulations

EPA Science Inventory

This paper presents a wind tunnel study of the effects of elongated rectangular buildings on the dispersion of pollutants from nearby stacks. The study examines the influence of source location, building aspect ratio, and wind direction on pollutant dispersion with the goal of de...

APPLICATIONS OF CFD SIMULATIONS OF POLLUTANT TRANSPORT AND DISPERSION WITHIN AMBIENT URBAN BUILDING ENVIRONMENTS: INCLUDING HOMELAND SECURITY

EPA Science Inventory

There is presently much focus on Homeland Security and the need to understand how potential sources of toxic material are transported and dispersed in the urban environment. Material transport and dispersion within these urban centers is highly influenced by the buildings. Compu...

Toxicities of Oils, Dispersants and Dispersed Oils to Aquatic Plants: Summary and Database Value to Resource Sustainability

EPA Science Inventory

Understanding the phytotoxicities of crude and dispersed oils is important for near-shore ecosystem management, particularly post-oil spills. One source of information is toxicity data summaries which are scattered and outdated for aquatic plants and petrochemicals. As a resu...

Estimation of errors in the inverse modeling of accidental release of atmospheric pollutant: Application to the reconstruction of the cesium-137 and iodine-131 source terms from the Fukushima Daiichi power plant

NASA Astrophysics Data System (ADS)

Winiarek, Victor; Bocquet, Marc; Saunier, Olivier; Mathieu, Anne

2012-03-01

A major difficulty when inverting the source term of an atmospheric tracer dispersion problem is the estimation of the prior errors: those of the atmospheric transport model, those ascribed to the representativity of the measurements, those that are instrumental, and those attached to the prior knowledge on the variables one seeks to retrieve. In the case of an accidental release of pollutant, the reconstructed source is sensitive to these assumptions. This sensitivity makes the quality of the retrieval dependent on the methods used to model and estimate the prior errors of the inverse modeling scheme. We propose to use an estimation method for the errors' amplitude based on the maximum likelihood principle. Under semi-Gaussian assumptions, it takes into account, without approximation, the positivity assumption on the source. We apply the method to the estimation of the Fukushima Daiichi source term using activity concentrations in the air. The results are compared to an L-curve estimation technique and to Desroziers's scheme. The total reconstructed activities significantly depend on the chosen method. Because of the poor observability of the Fukushima Daiichi emissions, these methods provide lower bounds for cesium-137 and iodine-131 reconstructed activities. These lower bound estimates, 1.2 × 1016 Bq for cesium-137, with an estimated standard deviation range of 15%-20%, and 1.9 - 3.8 × 1017 Bq for iodine-131, with an estimated standard deviation range of 5%-10%, are of the same order of magnitude as those provided by the Japanese Nuclear and Industrial Safety Agency and about 5 to 10 times less than the Chernobyl atmospheric releases.

A model for dispersion from area sources in convective turbulence. [for air pollution

NASA Technical Reports Server (NTRS)

Crane, G.; Panofsky, H. A.; Zeman, O.

1977-01-01

Four independent estimates of the vertical distribution of the eddy coefficient for dispersion of a passive contaminant from an extensive area source in a convective layer have been presented. The estimates were based on the following methods: (1) a second-order closure prediction, (2) field data of pollutant concentrations over Los Angeles, (3) lab measurements of particle dispersion, and (4) assumption of equality between momentum and mass transfer coefficients in the free convective limit. It is suggested that K-values estimated both from second-order closure theory and from Los Angeles measurements are systematically underestimated.

Status of wind-energy conversion

NASA Technical Reports Server (NTRS)

Thomas, R. L.; Savino, J. M.

1973-01-01

The utilization of wind energy is technically feasible as evidenced by the many past demonstrations of wind generators. The cost of energy from the wind has been high compared to fossil fuel systems. A sustained development effort is needed to obtain economical systems. The variability of the wind makes it an unreliable source on a short-term basis. However, the effects of this variability can be reduced by storage systems or connecting wind generators to fossil fuel systems, hydroelectric systems, or dispersing them throughout a large grid network. The NSF and NASA-Lewis Research Center have sponsored programs for the utilization of wind energy.

Genetic consequences of seed dispersal to sleeping trees by white-bellied spider monkeys

NASA Astrophysics Data System (ADS)

Karubian, Jordan; Ottewell, Kym; Link, Andres; Di Fiore, Anthony

2015-10-01

Frugivorous animals frequently generate clumped distributions of seeds away from source trees via 'destination-based' dispersal processes. For example, use of traditional sleeping trees by white-bellied spider monkeys Ateles belzebuth generates high densities of seeds of a preferred food source, the palm Oenocarpus bataua, at these sites. Little is known about the maternal seed source diversity and population genetic metrics of seed pools encountered at these sites. Given the repeated use of sleeping trees over time, and the fluid social organization and wide ranging movements exhibited by spider monkeys, we predicted that O. bataua seed pools beneath sleeping trees would be characterized by relatively high values of maternal seed source diversity and standard metrics of genetic diversity. Contrary to these expectations, we found relatively low average maternal seed source diversity beneath each of 6 sleeping trees we studied (weighted mean α = 3.74), but considerable variation in diversity of maternal seed sources between sleeping trees (range = 1.75-10.1) and high heterogeneity in standard genetic diversity measures between sleeping trees. There was no evidence for overlap in maternal seed sources between sleeping tree sites (δ = 1.0), resulting in significant genetic differentiation (Fst = 0.055-0.319) between these sites. Observed variation between sleeping trees could not be explained by the number of individual spider monkeys whose core home ranges included a given tree, nor by distance to a central mineral lick, a focal point of spider monkey activity. These findings suggest that spider monkey seed dispersal to sleeping trees is spatially restricted, perhaps because the animals visit sleeping trees at the end of the day and therefore only disperse O. bataua fruits that they ingest late in the day. These results add to our growing appreciation of the ways frugivore behavior mechanistically shapes seed dispersal outcomes.

Wind-tunnel Modelling of Dispersion from a Scalar Area Source in Urban-Like Roughness

NASA Astrophysics Data System (ADS)

Pascheke, Frauke; Barlow, Janet F.; Robins, Alan

2008-01-01

A wind-tunnel study was conducted to investigate ventilation of scalars from urban-like geometries at neighbourhood scale by exploring two different geometries a uniform height roughness and a non-uniform height roughness, both with an equal plan and frontal density of λ p = λ f = 25%. In both configurations a sub-unit of the idealized urban surface was coated with a thin layer of naphthalene to represent area sources. The naphthalene sublimation method was used to measure directly total area-averaged transport of scalars out of the complex geometries. At the same time, naphthalene vapour concentrations controlled by the turbulent fluxes were detected using a fast Flame Ionisation Detection (FID) technique. This paper describes the novel use of a naphthalene coated surface as an area source in dispersion studies. Particular emphasis was also given to testing whether the concentration measurements were independent of Reynolds number. For low wind speeds, transfer from the naphthalene surface is determined by a combination of forced and natural convection. Compared with a propane point source release, a 25% higher free stream velocity was needed for the naphthalene area source to yield Reynolds-number-independent concentration fields. Ventilation transfer coefficients w T / U derived from the naphthalene sublimation method showed that, whilst there was enhanced vertical momentum exchange due to obstacle height variability, advection was reduced and dispersion from the source area was not enhanced. Thus, the height variability of a canopy is an important parameter when generalising urban dispersion. Fine resolution concentration measurements in the canopy showed the effect of height variability on dispersion at street scale. Rapid vertical transport in the wake of individual high-rise obstacles was found to generate elevated point-like sources. A Gaussian plume model was used to analyse differences in the downstream plumes. Intensified lateral and vertical plume spread and plume dilution with height was found for the non-uniform height roughness.

Predictive Simulation of Gas Adsorption in Fixed-Beds and Limitations due to the Ill-Posed Danckwerts Boundary Condition

NASA Technical Reports Server (NTRS)

Knox, James Clinton

2016-01-01

The 1-D axially dispersed plug flow model is a mathematical model widely used for the simulation of adsorption processes. Lumped mass transfer coefficients such as the Glueckauf linear driving force (LDF) term and the axial dispersion coefficient are generally obtained by fitting simulation results to the experimental breakthrough test data. An approach is introduced where these parameters, along with the only free parameter in the energy balance equations, are individually fit to specific test data that isolates the appropriate physics. It is shown that with this approach this model provides excellent simulation results for the C02 on zeolite SA sorbent/sorbate system; however, for the H20 on zeolite SA system, non-physical deviations from constant pattern behavior occur when fitting dispersive experimental results with a large axial dispersion coefficient. A method has also been developed that determines a priori what values of the LDF and axial dispersion terms will result in non-physical simulation results for a specific sorbent/sorbate system when using the one-dimensional axially dispersed plug flow model. A relationship between the steepness of the adsorption equilibrium isotherm as indicated by the distribution factor, the magnitude of the axial dispersion and mass transfer coefficient, and the resulting non-physical behavior is derived. This relationship is intended to provide a guide for avoiding non-physical behavior by limiting the magnitude of the axial dispersion term on the basis of the mass transfer coefficient and distribution factor.

Ambient noise tomography with non-uniform noise sources and low aperture networks: case study of deep geothermal reservoirs in northern Alsace, France

NASA Astrophysics Data System (ADS)

Lehujeur, Maximilien; Vergne, Jérôme; Maggi, Alessia; Schmittbuhl, Jean

2017-01-01

We developed and applied a method for ambient noise surface wave tomography that can deal with noise cross-correlation functions governed to first order by a non-uniform distribution of the ambient seismic noise sources. The method inverts the azimuthal distribution of noise sources that are assumed to be far from the network, together with the spatial variations of the phase and group velocities on an optimized irregular grid. Direct modelling of the two-sided noise correlation functions avoids dispersion curve picking on every station pair and minimizes analyst intervention. The method involves station pairs spaced by distances down to a fraction of a wavelength, thereby bringing additional information for tomography. After validating the method on synthetic data, we applied it to a set of long-term continuous waveforms acquired around the geothermal sites at Soultz-sous-Forêts and Rittershoffen (Northern Alsace, France). For networks with limited aperture, we show that taking the azimuthal variations of the noise energy into account has significant impact on the surface wave dispersion maps. We obtained regional phase and group velocity models in the 1-7 s period range, which is sensitive to the structures encompassing the geothermal reservoirs. The ambient noise in our dataset originates from two main directions, the northern Atlantic Ocean and the Mediterranean Sea, and is dominated by the first Rayleigh wave overtone in the 2-5 s period range.

Application of CFD (Fluent) to LNG spills into geometrically complex environments.

PubMed

Gavelli, Filippo; Bullister, Edward; Kytomaa, Harri

2008-11-15

Recent discussions on the fate of LNG spills into impoundments have suggested that the commonly used combination of SOURCE5 and DEGADIS to predict the flammable vapor dispersion distances is not accurate, as it does not account for vapor entrainment by wind. SOURCE5 assumes the vapor layer to grow upward uniformly in the form of a quiescent saturated gas cloud that ultimately spills over impoundment walls. The rate of spillage is then used as the source term for DEGADIS. A more rigorous approach to predict the flammable vapor dispersion distance is to use a computational fluid dynamics (CFD) model. CFD codes can take into account the physical phenomena that govern the fate of LNG spills into impoundments, such as the mixing between air and the evaporated gas. Before a CFD code can be proposed as an alternate method for the prediction of flammable vapor cloud distances, it has to be validated with proper experimental data. This paper describes the use of Fluent, a widely-used commercial CFD code, to simulate one of the tests in the "Falcon" series of LNG spill tests. The "Falcon" test series was the only series that specifically addressed the effects of impoundment walls and construction obstructions on the behavior and dispersion of the vapor cloud. Most other tests, such as the Coyote and the Burro series, involved spills onto water and relatively flat ground. The paper discusses the critical parameters necessary for a CFD model to accurately predict the behavior of a cryogenic spill in a geometrically complex domain, and presents comparisons between the gas concentrations measured during the Falcon-1 test and those predicted using Fluent. Finally, the paper discusses the effect vapor barriers have in containing part of the spill thereby shortening the ignitable vapor cloud and therefore the required hazard area. This issue was addressed by comparing the Falcon-1 simulation (spill into the impoundment) with the simulation of an identical spill without any impoundment walls, or obstacles within the impoundment area.

Chapter 34: Geology and petroleum potential of the rifted margins of the Canada Basin

USGS Publications Warehouse

Houseknecht, D.W.; Bird, K.J.

2011-01-01

Three sides of the Canada Basin are bordered by high-standing, conjugate rift shoulders of the Chukchi Borderland, Alaska and Canada. The Alaska and Canada margins are mantled with thick, growth-faulted sediment prisms, and the Chukchi Borderland contains only a thin veneer of sediment. The rift-margin strata of Alaska and Canada reflect the tectonics and sediment dispersal systems of adjacent continental regions whereas the Chukchi Borderland was tectonically isolated from these sediment dispersal systems. Along the eastern Alaska-southern Canada margin, termed herein the 'Canning-Mackenzie deformed margin', the rifted margin is deformed by ongoing Brooks Range tectonism. Additional contractional structures occur in a gravity fold belt that may be present along the entire Alaska and Canada margins of the Canada Basin. Source-rock data inboard of the rift shoulders and regional palaeogeographic reconstructions suggest three potential source-rock intervals: Lower Cretaceous (Hauterivian-Albian), Upper Cretaceous (mostly Turonian) and Lower Palaeogene. Burial history modelling indicates favourable timing for generation from all three intervals beneath the Alaska and Canada passive margins, and an active petroleum system has been documented in the Canning-Mackenzie deformed margin. Assessment of undiscovered petroleum resources indicates the greatest potential in the Canning-Mackenzie deformed margin and significant potential in the Canada and Alaska passive margins. ?? 2011 The Geological Society of London.

A finite-volume ELLAM for three-dimensional solute-transport modeling

USGS Publications Warehouse

Russell, T.F.; Heberton, C.I.; Konikow, Leonard F.; Hornberger, G.Z.

2003-01-01

A three-dimensional finite-volume ELLAM method has been developed, tested, and successfully implemented as part of the U.S. Geological Survey (USGS) MODFLOW-2000 ground water modeling package. It is included as a solver option for the Ground Water Transport process. The FVELLAM uses space-time finite volumes oriented along the streamlines of the flow field to solve an integral form of the solute-transport equation, thus combining local and global mass conservation with the advantages of Eulerian-Lagrangian characteristic methods. The USGS FVELLAM code simulates solute transport in flowing ground water for a single dissolved solute constituent and represents the processes of advective transport, hydrodynamic dispersion, mixing from fluid sources, retardation, and decay. Implicit time discretization of the dispersive and source/sink terms is combined with a Lagrangian treatment of advection, in which forward tracking moves mass to the new time level, distributing mass among destination cells using approximate indicator functions. This allows the use of large transport time increments (large Courant numbers) with accurate results, even for advection-dominated systems (large Peclet numbers). Four test cases, including comparisons with analytical solutions and benchmarking against other numerical codes, are presented that indicate that the FVELLAM can usually yield excellent results, even if relatively few transport time steps are used, although the quality of the results is problem-dependent.

Impact localization in dispersive waveguides based on energy-attenuation of waves with the traveled distance

NASA Astrophysics Data System (ADS)

Alajlouni, Sa'ed; Albakri, Mohammad; Tarazaga, Pablo

2018-05-01

An algorithm is introduced to solve the general multilateration (source localization) problem in a dispersive waveguide. The algorithm is designed with the intention of localizing impact forces in a dispersive floor, and can potentially be used to localize and track occupants in a building using vibration sensors connected to the lower surface of the walking floor. The lower the wave frequencies generated by the impact force, the more accurate the localization is expected to be. An impact force acting on a floor, generates a seismic wave that gets distorted as it travels away from the source. This distortion is noticeable even over relatively short traveled distances, and is mainly caused by the dispersion phenomenon among other reasons, therefore using conventional localization/multilateration methods will produce localization error values that are highly variable and occasionally large. The proposed localization approach is based on the fact that the wave's energy, calculated over some time window, decays exponentially as the wave travels away from the source. Although localization methods that assume exponential decay exist in the literature (in the field of wireless communications), these methods have only been considered for wave propagation in non-dispersive media, in addition to the limiting assumption required by these methods that the source must not coincide with a sensor location. As a result, these methods cannot be applied to the indoor localization problem in their current form. We show how our proposed method is different from the other methods, and that it overcomes the source-sensor location coincidence limitation. Theoretical analysis and experimental data will be used to motivate and justify the pursuit of the proposed approach for localization in a dispersive medium. Additionally, hammer impacts on an instrumented floor section inside an operational building, as well as finite element model simulations, are used to evaluate the performance of the algorithm. It is shown that the algorithm produces promising results providing a foundation for further future development and optimization.

A multi-source probabilistic hazard assessment of tephra dispersal in the Neapolitan area

NASA Astrophysics Data System (ADS)

Sandri, Laura; Costa, Antonio; Selva, Jacopo; Folch, Arnau; Macedonio, Giovanni; Tonini, Roberto

2015-04-01

In this study we present the results obtained from a long-term Probabilistic Hazard Assessment (PHA) of tephra dispersal in the Neapolitan area. Usual PHA for tephra dispersal needs the definition of eruptive scenarios (usually by grouping eruption sizes and possible vent positions in a limited number of classes) with associated probabilities, a meteorological dataset covering a representative time period, and a tephra dispersal model. PHA then results from combining simulations considering different volcanological and meteorological conditions through weights associated to their specific probability of occurrence. However, volcanological parameters (i.e., erupted mass, eruption column height, eruption duration, bulk granulometry, fraction of aggregates) typically encompass a wide range of values. Because of such a natural variability, single representative scenarios or size classes cannot be adequately defined using single values for the volcanological inputs. In the present study, we use a method that accounts for this within-size-class variability in the framework of Event Trees. The variability of each parameter is modeled with specific Probability Density Functions, and meteorological and volcanological input values are chosen by using a stratified sampling method. This procedure allows for quantifying hazard without relying on the definition of scenarios, thus avoiding potential biases introduced by selecting single representative scenarios. Embedding this procedure into the Bayesian Event Tree scheme enables the tephra fall PHA and its epistemic uncertainties. We have appied this scheme to analyze long-term tephra fall PHA from Vesuvius and Campi Flegrei, in a multi-source paradigm. We integrate two tephra dispersal models (the analytical HAZMAP and the numerical FALL3D) into BET_VH. The ECMWF reanalysis dataset are used for exploring different meteorological conditions. The results obtained show that PHA accounting for the whole natural variability are consistent with previous probabilities maps elaborated for Vesuvius and Campi Flegrei on the basis of single representative scenarios, but show significant differences. In particular, the area characterized by a 300 kg/m2-load exceedance probability larger than 5%, accounting for the whole range of variability (that is, from small violent strombolian to plinian eruptions), is similar to that displayed in the maps based on the medium magnitude reference eruption, but it is of a smaller extent. This is due to the relatively higher weight of the small magnitude eruptions considered in this study, but neglected in the reference scenario maps. On the other hand, in our new maps the area characterized by a 300 kg/m2-load exceedance probability larger than 1% is much larger than that of the medium magnitude reference eruption, due to the contribution of plinian eruptions at lower probabilities, again neglected in the reference scenario maps.

49 CFR 173.115 - Class 2, Divisions 2.1, 2.2, and 2.3-Definitions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 3A1800”, the service pressure is 12410 kPa (1800 psig). (j) Refrigerant gas or Dispersant gas. The terms Refrigerant gas and Dispersant gas apply to all nonpoisonous refrigerant gases; dispersant gases... °F), used only as a refrigerant, dispersant, or blowing agent. (k) For Division 2.2 gases, the...

49 CFR 173.115 - Class 2, Divisions 2.1, 2.2, and 2.3-Definitions.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 3A1800”, the service pressure is 12410 kPa (1800 psig). (j) Refrigerant gas or Dispersant gas. The terms Refrigerant gas and Dispersant gas apply to all nonpoisonous refrigerant gases; dispersant gases... °F), used only as a refrigerant, dispersant, or blowing agent. (k) For Division 2.2 gases, the...

Étude comparative des techniques d'analyse par fluorescence X à dispersion d'énergie (ED-XRF) et à dispersion de longueur d'onde (WD-XRF), et par spectrométrie d'émission atomique à source plasma couplée par induction (ICP-AES)

NASA Astrophysics Data System (ADS)

Rahmani, A.; Benyaïch, F.; Bounakhla, M.; Bilal, E.; Moutte, J.; Gruffat, J. J.; Zahry, F.

2004-11-01

Dans ce travail, nous présentons une étude comparative des techniques d'analyse par fluorescence X à dispersion d'énergie (ED-XRF) et à dispersion de longueur d'onde (WD-XRF), et par spectrométrie d'émission atomique à source plasma couplée par induction (ICP-AES). Les résultats de la calibration des spectromètres à dispersion d'énergie, à excitation par sources radioactives (55Fe, 109Cd et 241Am) et à excitation secondaire (cible secondaire Mo et Cu) du Centre National pour l'Energie, les Sciences et les Techniques Nucléaires (CNESTEN, Rabat, Maroc) sur des échantillons étalons de références de l'Agence International de l'Energie Atomique (AIEA) et du Community Bureau of Référence (BCR) ont été comparés aux résultats d'analyse des mêmes échantillons étalons par la spectrométrie X à dispersion de longueur d'onde (WD-XRF) et par spectrométrie d'émission atomique à source plasma couplé par induction (ICP-AES) au département GENERIC du centre SPIN à l'Ecole des Mines de Saint-Etienne (France). Les trois techniques d'analyse utilisées donnent des résultats comparables pour le dosage des éléments majeurs, alors que pour les traces on note des déviations importantes à cause des effets de matrice qui sont difficiles à corriger dans le cas de la fluorescence X.

Effects of pore-scale dispersion, degree of heterogeneity, sampling size, and source volume on the concentration moments of conservative solutes in heterogeneous formations

Treesearch

Daniele Tonina; Alberto Bellin

2008-01-01

Pore-scale dispersion (PSD), aquifer heterogeneity, sampling volume, and source size influence solute concentrations of conservative tracers transported in heterogeneous porous formations. In this work, we developed a new set of analytical solutions for the concentration ensemble mean, variance, and coefficient of variation (CV), which consider the effects of all these...

SETI Searches for Radio Transients from Kepler Field Planets and Astropulse Candidates

NASA Astrophysics Data System (ADS)

Gautam, Abhimat Krishna; Siemion, Andrew; Korpela, Eric J.; Cobb, Jeff; Lebofsky, Matt; Werthimer, Dan

2014-06-01

We present a search for fast radio transients in targeted observations of planet candidates in the Kepler Field and candidate Astropulse sources.Kepler Field observations were conducted in the band 1.1 and 1.9 GHz using the Green Bank Telescope in Green Bank, West Virginia and are centered on 86 stars hosting candidate planets identified by the Kepler spacecraft. These stars were chosen based on the properties of their putative planetary system thought to be conducive to the development of advanced life, including all systems known (as of May 2011) hosting a Kepler Object of Interest (KOI) with a calculated equilibrium temperature between 230 and 380 K, at least 4 KOIs or a KOI with an inferred radius < 3.0 r_earth and a period > 50 d. The Kepler Field is centered at an intermediate galactic latitude, b = 13.5°, which presents an additional opportunity to detect signals from the older population of millisecond and recycled pulsars located above the galactic plane.The Astropulse radio survey searches for brief wide-band pulses in a 2.5 MHz band centered at 1420 MHz using commensal data recorded from the Arecibo ALFA receiver. In early Astropulse analysis, 108 candidate sources were identified that passed a series of tests designed to eliminate potential sources of radio frequency interference (RFI). We have performed targeted re-observations of these sources at Arecibo over the full (1214-1536 MHz) ALFA band.We have developed a software pipeline to locate fast dispersed transients in these observations, leveraging components of the PRESTO software library. This pipeline consists of finding and removing RFI, conducting de-dispersion to remove the effects of dispersion from the interstellar medium (ISM) on the signal and identifying over- threshold events. We also perform de-dispersion at negative dispersion measures, proposed to be a potential technique for intelligent civilizations to distinguish their emission from natural sources. We carry out both a periodicity and single-pulse search on de-dispersed time series. The outputs from these steps are examined to look for both technological and astrophysical sources of impulsive radio emission.

Long-term colonization ecology of forest-dwelling species in a fragmented rural landscape - dispersal versus establishment.

PubMed

Lõhmus, Kertu; Paal, Taavi; Liira, Jaan

2014-08-01

Species colonization in a new habitat patch is an efficiency indicator of biodiversity conservation. Colonization is a two-step process of dispersal and establishment, characterized by the compatibility of plant traits with landscape structure and habitat conditions. Therefore, ecological trait profiling of specialist species is initially required to estimate the relative importance of colonization filters. Old planted parks best satisfy the criteria of a newly created and structurally matured habitat for forest-dwelling plant species. We sampled species in 230 ancient deciduous forests (source habitat), 74 closed-canopy manor parks (target habitats), 151 linear wooded habitats (landscape corridors), and 97 open habitats (isolating matrix) in Estonia. We defined two species groups of interest: forest (107 species) and corridor specialists (53 species). An extra group of open habitat specialists was extracted for trait scaling. Differing from expectations, forest specialists have high plasticity in reproduction mechanisms: smaller seeds, larger dispersules, complementary selfing ability, and diversity of dispersal vectors. Forest specialists are shorter, less nutrient-demanding and mycorrhizal-dependent, stress-tolerant disturbance-sensitive competitors, while corridor specialists are large-seeded disturbance-tolerant competitors. About 40% of species from local species pools have immigrated into parks. The historic forest area, establishment-related traits, and stand quality enhance the colonization of forest specialists. The openness of landscape and mowing in the park facilitate corridor specialists. Species traits in parks vary between a forest and corridor specialist, except for earlier flowering and larger propagules. Forest species are not dispersal limited, but they continue to be limited by habitat properties even in the long term. Therefore, the shady parts of historic parks should be appreciated as important forest biodiversity-enhancing landscape structures. The habitat quality of secondary stands can be improved by nurturing a heterogeneous shrub and tree layer, and modest herb layer management.

Long-term colonization ecology of forest-dwelling species in a fragmented rural landscape – dispersal versus establishment

PubMed Central

Lõhmus, Kertu; Paal, Taavi; Liira, Jaan

2014-01-01

Species colonization in a new habitat patch is an efficiency indicator of biodiversity conservation. Colonization is a two-step process of dispersal and establishment, characterized by the compatibility of plant traits with landscape structure and habitat conditions. Therefore, ecological trait profiling of specialist species is initially required to estimate the relative importance of colonization filters. Old planted parks best satisfy the criteria of a newly created and structurally matured habitat for forest-dwelling plant species. We sampled species in 230 ancient deciduous forests (source habitat), 74 closed-canopy manor parks (target habitats), 151 linear wooded habitats (landscape corridors), and 97 open habitats (isolating matrix) in Estonia. We defined two species groups of interest: forest (107 species) and corridor specialists (53 species). An extra group of open habitat specialists was extracted for trait scaling. Differing from expectations, forest specialists have high plasticity in reproduction mechanisms: smaller seeds, larger dispersules, complementary selfing ability, and diversity of dispersal vectors. Forest specialists are shorter, less nutrient-demanding and mycorrhizal-dependent, stress-tolerant disturbance-sensitive competitors, while corridor specialists are large-seeded disturbance-tolerant competitors. About 40% of species from local species pools have immigrated into parks. The historic forest area, establishment-related traits, and stand quality enhance the colonization of forest specialists. The openness of landscape and mowing in the park facilitate corridor specialists. Species traits in parks vary between a forest and corridor specialist, except for earlier flowering and larger propagules. Forest species are not dispersal limited, but they continue to be limited by habitat properties even in the long term. Therefore, the shady parts of historic parks should be appreciated as important forest biodiversity-enhancing landscape structures. The habitat quality of secondary stands can be improved by nurturing a heterogeneous shrub and tree layer, and modest herb layer management. PMID:25247068

A technique for marking first-stage larvae of the gypsy moth for dispersal studies

Treesearch

Thomas M. Odell; Ian H. von Lindern

1976-01-01

Zinc cadmium sulfide fluorescent particles can be used to mark first stage larvae of the gypsy moth, Porthetria dispar (L.), without effecting changes in their development and behavior. Marked larvae dispersed readily; so the technique could be used to correlate dispersed larvae with any particular source point.

Comparison of AERMOD and WindTrax dispersion models in determining PM10 emission rates from beef cattle feedlots

USDA-ARS?s Scientific Manuscript database

Reverse dispersion modeling has been used to determine air emission fluxes from ground-level area sources, including open-lot beef cattle feedlots. This research compared AERMOD, a Gaussian-based and currently the U.S. Environmental Protection Agency (EPA) preferred regulatory dispersion model, and ...

Improving bioaerosol exposure assessments of composting facilities — Comparative modelling of emissions from different compost ages and processing activities

NASA Astrophysics Data System (ADS)

Taha, M. P. M.; Drew, G. H.; Tamer, A.; Hewings, G.; Jordinson, G. M.; Longhurst, P. J.; Pollard, S. J. T.

We present bioaerosol source term concentrations from passive and active composting sources and compare emissions from green waste compost aged 1, 2, 4, 6, 8, 12 and 16 weeks. Results reveal that the age of compost has little effect on the bioaerosol concentrations emitted for passive windrow sources. However emissions from turning compost during the early stages may be higher than during the later stages of the composting process. The bioaerosol emissions from passive sources were in the range of 10 3-10 4 cfu m -3, with releases from active sources typically 1-log higher. We propose improvements to current risk assessment methodologies by examining emission rates and the differences between two air dispersion models for the prediction of downwind bioaerosol concentrations at off-site points of exposure. The SCREEN3 model provides a more precautionary estimate of the source depletion curves of bioaerosol emissions in comparison to ADMS 3.3. The results from both models predict that bioaerosol concentrations decrease to below typical background concentrations before 250 m, the distance at which the regulator in England and Wales may require a risk assessment to be completed.

The influence of the dispersion corrections on the performance of DFT method in modeling HNgY noble gas molecules and their complexes

NASA Astrophysics Data System (ADS)

Cukras, Janusz; Sadlej, Joanna

2018-01-01

The letter reports a comparative assessment of the usefulness of the two different Grimme's corrections for evaluating dispersion interaction (DFT-D3 and DFT-D3BJ) for the representative molecules of the family of noble-gas hydrides HXeY and their complexes with the HZ molecules, where Y and Z are F/Cl/OH/SH. with special regard to the dispersion term calculated by means of the symmetry-adapted perturbation theory (at the SAPT0 level). The results indicate that despite differences in the total interactions energy (DFT + corrections) versus SAPT0 results, the sequence of contributions of the individual dispersion terms is still maintained. Both dispersion corrections perform similarly and they improve the results suggesting that it is worthwhile to include them in calculations.

Multiwalled Carbon Nanotube Dispersion Methods Affect Their Aggregation, Deposition, and Biomarker Response

EPA Science Inventory

To systematically evaluate how dispersion methods affect the environmental behaviors of multiwalled carbon nanotubes (MWNTs), MWNTs were dispersed in various solutions (e.g., surfactants, natural organic matter (NOM), and etc.) via ultrasonication (SON) and long-term stirring (LT...

Atmospheric aerosol source identification and estimates of source contributions to air pollution in Dundee, UK

NASA Astrophysics Data System (ADS)

Qin, Y.; Oduyemi, K.

Anthropogenic aerosol (PM 10) emission sources sampled at an air quality monitoring station in Dundee have been analysed. However, the information on local natural aerosol emission sources was unavailable. A method that combines receptor model and atmospheric dispersion model was used to identify aerosol sources and estimate source contributions to air pollution. The receptor model identified five sources. These are aged marine aerosol source with some chlorine replaced by sulphate, secondary aerosol source of ammonium sulphate, secondary aerosol source of ammonium nitrate, soil and construction dust source, and incinerator and fuel oil burning emission source. For the vehicle emission source, which has been comprehensively described in the atmospheric emission inventory but cannot be identified by the receptor model, an atmospheric dispersion model was used to estimate its contributions. In Dundee, a significant percentage, 67.5%, of the aerosol mass sampled at the study station could be attributed to the six sources named above.

Code System for Performance Assessment Ground-water Analysis for Low-level Nuclear Waste.

DOE Office of Scientific and Technical Information (OSTI.GOV)

MATTHEW,; KOZAK, W.

1994-02-09

Version 00 The PAGAN code system is a part of the performance assessment methodology developed for use by the U. S. Nuclear Regulatory Commission in evaluating license applications for low-level waste disposal facilities. In this methodology, PAGAN is used as one candidate approach for analysis of the ground-water pathway. PAGAN, Version 1.1 has the capability to model the source term, vadose-zone transport, and aquifer transport of radionuclides from a waste disposal unit. It combines the two codes SURFACE and DISPERSE which are used as semi-analytical solutions to the convective-dispersion equation. This system uses menu driven input/out for implementing a simplemore » ground-water transport analysis and incorporates statistical uncertainty functions for handling data uncertainties. The output from PAGAN includes a time- and location-dependent radionuclide concentration at a well in the aquifer, or a time- and location-dependent radionuclide flux into a surface-water body.« less

White-light Interferometry using a Channeled Spectrum: II. Calibration Methods, Numerical and Experimental Results

NASA Technical Reports Server (NTRS)

Zhai, Chengxing; Milman, Mark H.; Regehr, Martin W.; Best, Paul K.

2007-01-01

In the companion paper, [Appl. Opt. 46, 5853 (2007)] a highly accurate white light interference model was developed from just a few key parameters characterized in terms of various moments of the source and instrument transmission function. We develop and implement the end-to-end process of calibrating these moment parameters together with the differential dispersion of the instrument and applying them to the algorithms developed in the companion paper. The calibration procedure developed herein is based on first obtaining the standard monochromatic parameters at the pixel level: wavenumber, phase, intensity, and visibility parameters via a nonlinear least-squares procedure that exploits the structure of the model. The pixel level parameters are then combined to obtain the required 'global' moment and dispersion parameters. The process is applied to both simulated scenarios of astrometric observations and to data from the microarcsecond metrology testbed (MAM), an interferometer testbed that has played a prominent role in the development of this technology.

Extracting spatial information from large aperture exposures of diffuse sources

NASA Technical Reports Server (NTRS)

Clarke, J. T.; Moos, H. W.

1981-01-01

The spatial properties of large aperture exposures of diffuse emission can be used both to investigate spatial variations in the emission and to filter out camera noise in exposures of weak emission sources. Spatial imaging can be accomplished both parallel and perpendicular to dispersion with a resolution of 5-6 arc sec, and a narrow median filter running perpendicular to dispersion across a diffuse image selectively filters out point source features, such as reseaux marks and fast particle hits. Spatial information derived from observations of solar system objects is presented.

Uncovering dispersion properties in semiconductor waveguides to study photon-pair generation

NASA Astrophysics Data System (ADS)

Laiho, K.; Pressl, B.; Schlager, A.; Suchomel, H.; Kamp, M.; Höfling, S.; Schneider, C.; Weihs, G.

2016-10-01

We investigate the dispersion properties of ridge Bragg-reflection waveguides to deduce their phasematching characteristics. These are crucial for exploiting them as sources of parametric down-conversion (PDC). In order to estimate the phasematching bandwidth we first determine the group refractive indices of the interacting modes via Fabry-Perot experiments in two distant wavelength regions. Second, by measuring the spectra of the emitted PDC photons, we gain access to their group index dispersion. Our results offer a simple approach for determining the PDC process parameters in the spectral domain, and provide important feedback for designing such sources, especially in the broadband case.

Research on the middle-of-receiver-spread assumption of the MASW method

USGS Publications Warehouse

Luo, Y.; Xia, J.; Liu, J.; Xu, Y.; Liu, Q.

2009-01-01

The multichannel analysis of surface wave (MASW) method has been effectively used to determine near-surface shear- (S-) wave velocity. Estimating the S-wave velocity profile from Rayleigh-wave measurements is straightforward. A three-step process is required to obtain S-wave velocity profiles: acquisition of a multiple number of multichannel records along a linear survey line by use of the roll-along mode, extraction of dispersion curves of Rayleigh waves, and inversion of dispersion curves for an S-wave velocity profile for each shot gather. A pseudo-2D S-wave velocity section can be generated by aligning 1D S-wave velocity models. In this process, it is very important to understand where the inverted 1D S-wave velocity profile should be located: the midpoint of each spread (a middle-of-receiver-spread assumption) or somewhere between the source and the last receiver. In other words, the extracted dispersion curve is determined by the geophysical structure within the geophone spread or strongly affected by the source geophysical structure. In this paper, dispersion curves of synthetic datasets and a real-world example are calculated by fixing the receiver spread and changing the source location. Results demonstrate that the dispersion curves are mainly determined by structures within a receiver spread. ?? 2008 Elsevier Ltd. All rights reserved.

DTWT (Dispersive Tsunami Wave Tool): a new tool for computing the complete dispersion of tsunami travel time.

NASA Astrophysics Data System (ADS)

Reymond, Dominique

2017-04-01

We present a tool for computing the complete arrival times of the dispersed wave-train of a tsunami. The calculus is made using the exact formulation of the tsunami dispersion (and without approximations), at any desired periods between one hour or more (concerning the gravity waves propagation) until 10s (the highly dispersed mode). The computation of the travel times is based on the a summation of the necessary time for a tsunami to cross all the elementary blocs of a grid of bathymetry following a path between the source and receiver at a given period. In addition the source dimensions and the focal mechanism are taken into account to adjust the minimum travel time to the different possible points of emission of the source. A possible application of this tool is to forecast the arrival time of late arrivals of tsunami waves that could produce the resonnance of some bays and sites at higher frequencies than the gravity mode. The theoretical arrival times are compared to the observed ones and to the results obtained by TTT (P. Wessel, 2009) and the ones obtained by numerical simulations. References: Wessel, P. (2009). Analysis of oberved and predicted tsunami travel times for the Pacic and Indian oceans. Pure Appl. Geophys., 166:301-324.

Numerical dispersion compensation for Partial Coherence Interferometry and Optical Coherence Tomography.

PubMed

Fercher, A; Hitzenberger, C; Sticker, M; Zawadzki, R; Karamata, B; Lasser, T

2001-12-03

Dispersive samples introduce a wavelength dependent phase distortion to the probe beam. This leads to a noticeable loss of depth resolution in high resolution OCT using broadband light sources. The standard technique to avoid this consequence is to balance the dispersion of the sample byarrangingadispersive materialinthereference arm. However, the impact of dispersion is depth dependent. A corresponding depth dependent dispersion balancing technique is diffcult to implement. Here we present a numerical dispersion compensation technique for Partial Coherence Interferometry (PCI) and Optical Coherence Tomography (OCT) based on numerical correlation of the depth scan signal with a depth variant kernel. It can be used a posteriori and provides depth dependent dispersion compensation. Examples of dispersion compensated depth scan signals obtained from microscope cover glasses are presented.

Population synchrony of a native fish across three Laurentian Great Lakes: Evaluating the effects of dispersal and climate

USGS Publications Warehouse

Bunnell, D.B.; Adams, J.V.; Gorman, O.T.; Madenjian, C.P.; Riley, S.C.; Roseman, E.F.; Schaeffer, J.S.

2010-01-01

Climate and dispersal are the two most commonly cited mechanisms to explain spatial synchrony among time series of animal populations, and climate is typically most important for fishes. Using data from 1978-2006, we quantified the spatial synchrony in recruitment and population catch-per-unit-effort (CPUE) for bloater (Coregonus hoyi) populations across lakes Superior, Michigan, and Huron. In this natural field experiment, climate was highly synchronous across lakes but the likelihood of dispersal between lakes differed. When data from all lakes were pooled, modified correlograms revealed spatial synchrony to occur up to 800 km for long-term (data not detrended) trends and up to 600 km for short-term (data detrended by the annual rate of change) trends. This large spatial synchrony more than doubles the scale previously observed in freshwater fish populations, and exceeds the scale found in most marine or estuarine populations. When analyzing the data separately for within- and between-lake pairs, spatial synchrony was always observed within lakes, up to 400 or 600 km. Conversely, between-lake synchrony did not occur among short-term trends, and for long-term trends, the scale of synchrony was highly variable. For recruit CPUE, synchrony occurred up to 600 km between both lakes Michigan and Huron (where dispersal was most likely) and lakes Michigan and Superior (where dispersal was least likely), but failed to occur between lakes Huron and Superior (where dispersal likelihood was intermediate). When considering the scale of putative bloater dispersal and genetic information from previous studies, we concluded that dispersal was likely underlying within-lake synchrony but climate was more likely underlying between-lake synchrony. The broad scale of synchrony in Great Lakes bloater populations increases their probability of extirpation, a timely message for fishery managers given current low levels of bloater abundance. ?? Springer-Verlag 2009.

Numerical prediction on the dispersion of pollutant particles

NASA Astrophysics Data System (ADS)

Osman, Kahar; Ali, Zairi; Ubaidullah, S.; Zahid, M. N.

2012-06-01

The increasing concern on air pollution has led people around the world to find more efficient ways to control the problem. Air dispersion modeling is proven to be one of the alternatives that provide economical ways to control the growing threat of air pollution. The objective of this research is to develop a practical numerical algorithm to predict the dispersion of pollutant particles around a specific source of emission. The source selected was a rubber wood manufacturing plant. Gaussian-plume model were used as air dispersion model due to its simplicity and generic application. Results of this study show the concentrations of the pollutant particles on ground level reached approximately 90μg/m3, compared with other software. This value surpasses the limit of 50μg/m3 stipulated by the National Ambient Air Quality Standard (NAAQS) and Recommended Malaysian Guidelines (RMG) set by Environment Department of Malaysia. The results also show high concentration of pollutant particles reading during dru seasons as compared to that of rainy seasons. In general, the developed algorithm is proven to be able to predict particles distribution around emitted source with acceptable accuracy.

Improved quantification of CO2 emission at Campi Flegrei by combined Lagrangian Stochastic and Eulerian dispersion modelling

NASA Astrophysics Data System (ADS)

Pedone, Maria; Granieri, Domenico; Moretti, Roberto; Fedele, Alessandro; Troise, Claudia; Somma, Renato; De Natale, Giuseppe

2017-12-01

This study investigates fumarolic CO2 emissions at Campi Flegrei (Southern Italy) and their dispersion in the lowest atmospheric boundary layer. We innovatively utilize a Lagrangian Stochastic dispersion model (WindTrax) combined with an Eulerian model (DISGAS) to diagnose the dispersion of diluted gas plumes over large and complex topographic domains. New measurements of CO2 concentrations acquired in February and October 2014 in the area of Pisciarelli and Solfatara, the two major fumarolic fields of Campi Flegrei caldera, and simultaneous measurements of meteorological parameters are used to: 1) test the ability of WindTrax to calculate the fumarolic CO2 flux from the investigated sources, and 2) perform predictive numerical simulations to resolve the mutual interference between the CO2 emissions of the two adjacent areas. This novel approach allows us to a) better quantify the CO2 emission of the fumarolic source, b) discriminate ;true; CO2 contributions for each source, and c) understand the potential impact of the composite CO2 plume (Pisciarelli ;plus; Solfatara) on the highly populated areas inside the Campi Flegrei caldera.

Dispersive shock waves in systems with nonlocal dispersion of Benjamin-Ono type

NASA Astrophysics Data System (ADS)

El, G. A.; Nguyen, L. T. K.; Smyth, N. F.

2018-04-01

We develop a general approach to the description of dispersive shock waves (DSWs) for a class of nonlinear wave equations with a nonlocal Benjamin-Ono type dispersion term involving the Hilbert transform. Integrability of the governing equation is not a pre-requisite for the application of this method which represents a modification of the DSW fitting method previously developed for dispersive-hydrodynamic systems of Korteweg-de Vries (KdV) type (i.e. reducible to the KdV equation in the weakly nonlinear, long wave, unidirectional approximation). The developed method is applied to the Calogero-Sutherland dispersive hydrodynamics for which the classification of all solution types arising from the Riemann step problem is constructed and the key physical parameters (DSW edge speeds, lead soliton amplitude, intermediate shelf level) of all but one solution type are obtained in terms of the initial step data. The analytical results are shown to be in excellent agreement with results of direct numerical simulations.

Comprehensive Monitoring Program: Final Air Quality Data Assessment Report for FY90, Version 3.1 Volume 3

DTIC Science & Technology

1991-09-01

Monitoring Stations Figure 4.1-1 X /Q Dispersion for Phase I Figure 4.1-2 X /Q Dispersion for Phase 2-Stage 1 Figure 4.1-3 X /Q Dispersion for Phase 2...Stage 2 Fp Figure 4.1-4 X /Q Dispersion for Phase 3 Figure 4.1-5 X /Q Dispersion for Phase 4 • Figure 4.1-6 Sources of Regulated Pollutants in RMA...Arsenic Results by Phase "Figure 4.4-7 Cadmium Results by Phase Figure 4.4-8 X /Q Dispersion and Basin F Metals for 9/6/88 * Figure 4.4-9 X /Q Dispersion

Examination of climatological wind patterns and simulated pollen dispersion in a complex island environment

NASA Astrophysics Data System (ADS)

Viner, Brian J.; Arritt, Raymond W.; Westgate, Mark E.

2017-08-01

Complex terrain creates small-scale circulations which affect pollen dispersion but may be missed by meteorological observing networks and coarse-grid meteorological models. On volcanic islands, these circulations result from differing rates of surface heating between land and sea as well as rugged terrain. We simulated the transport of bentgrass, ryegrass, and maize pollen from 30 sources within the agricultural regions of the Hawaiian island Kaua'i during climatological conditions spanning season conditions and the La Niña, El Niño, and neutral phases of the El Niño-Southern Oscillation. Both pollen size and source location had major effects on predicted dispersion over and near the island. Three patterns of pollen dispersion were identified in response to prevailing wind conditions: southwest winds transported pollen inland, funneling pollen grains through valleys; east winds transported pollen over the ocean, with dispersive tails for the smallest pollen grains following the mean wind and extending as far as the island of Ni'ihau 35 km away; and northeast winds moved pollen inland counter to the prevailing flow due to a sea breeze circulation that formed over the source region. These results are the first to predict the interactions between complex island terrain and local climatology on grass pollen dispersion. They demonstrate how numerical modeling can provide guidance for field trials by illustrating the common flow regimes present in complex terrain, allowing field trials to focus on areas where successful sampling is more likely to occur.

BDW-1

EPA Pesticide Factsheets

This data set is associated with the results found in the journal article: Perry et al, 2016. Characterization of pollutant dispersion near elongated buildings based on wind tunnel simulations, Atmospheric Environment, 142, 286-295.The paper presents a wind tunnel study of the effects of elongated rectangular buildings on the dispersion of pollutants from nearby stacks. The study examines the influence of source location, building aspect ratio, and wind direction on pollutant dispersion with the goal of developing improved algorithms within dispersion models. The paper also examines the current AERMOD/PRIME modeling capabilities compared to wind tunnel observations. Differences in the amount of plume material entrained in the wake region downwind of a building for various source locations and source heights are illustrated with vertical and lateral concentration profiles. These profiles were parameterized using the Gaussian equation and show the influence of building/source configurations on those parameters. When the building is oriented at 4500b0 to the approach flow, for example, the effective plume height descends more rapidly than it does for a perpendicular building, enhancing the resulting surface concentrations in the wake region. Buildings at angles to the wind cause a cross-wind shift in the location of the plume resulting from a lateral mean flow established in the building wake. These and other effects that are not well represented in many dispersio

Seed production and dispersal by dwarf mistletoe in overstory jeffrey pines in California

Treesearch

Robert F. Scharpf; J. R. Parmeter Jr.

1971-01-01

Studies in northeastern California showed that the number of dwarf mistletoe (Arceuthobium campylopodum) seeds trapped declined at a logaithmic rate as the distance from overstory source of infection increased. The most seeds were dispersed in the direction of preuading winds. It Is quite likely that storms also aid dispersal. Total numbers of seeds...

Dense magnetized plasma associated with a fast radio burst.

PubMed

Masui, Kiyoshi; Lin, Hsiu-Hsien; Sievers, Jonathan; Anderson, Christopher J; Chang, Tzu-Ching; Chen, Xuelei; Ganguly, Apratim; Jarvis, Miranda; Kuo, Cheng-Yu; Li, Yi-Chao; Liao, Yu-Wei; McLaughlin, Maura; Pen, Ue-Li; Peterson, Jeffrey B; Roman, Alexander; Timbie, Peter T; Voytek, Tabitha; Yadav, Jaswant K

2015-12-24

Fast radio bursts are bright, unresolved, non-repeating, broadband, millisecond flashes, found primarily at high Galactic latitudes, with dispersion measures much larger than expected for a Galactic source. The inferred all-sky burst rate is comparable to the core-collapse supernova rate out to redshift 0.5. If the observed dispersion measures are assumed to be dominated by the intergalactic medium, the sources are at cosmological distances with redshifts of 0.2 to 1 (refs 10 and 11). These parameters are consistent with a wide range of source models. One fast burst revealed circular polarization of the radio emission, but no linear polarization was detected, and hence no Faraday rotation measure could be determined. Here we report the examination of archival data revealing Faraday rotation in the fast radio burst FRB 110523. Its radio flux and dispersion measure are consistent with values from previously reported bursts and, accounting for a Galactic contribution to the dispersion and using a model of intergalactic electron density, we place the source at a maximum redshift of 0.5. The burst has a much higher rotation measure than expected for this line of sight through the Milky Way and the intergalactic medium, indicating magnetization in the vicinity of the source itself or within a host galaxy. The pulse was scattered by two distinct plasma screens during propagation, which requires either a dense nebula associated with the source or a location within the central region of its host galaxy. The detection in this instance of magnetization and scattering that are both local to the source favours models involving young stellar populations such as magnetars over models involving the mergers of older neutron stars, which are more likely to be located in low-density regions of the host galaxy.

Long-term monitoring of persistent organic pollutants (POPs) at the Norwegian Troll station in Dronning Maud Land, Antarctica

NASA Astrophysics Data System (ADS)

Kallenborn, R.; Breivik, K.; Eckhardt, S.; Lunder, C. R.; Manø, S.; Schlabach, M.; Stohl, A.

2013-07-01

A first long-term monitoring of selected persistent organic pollutants (POPs) in Antarctic air has been conducted at the Norwegian research station Troll (Dronning Maud Land). As target contaminants 32 PCB congeners, α- and γ-hexachlorocyclohexane (HCH), trans- and cis-chlordane, trans- and cis-nonachlor, p,p'- and o,p-DDT, DDD, DDE as well as hexachlorobenzene (HCB) were selected. The monitoring program with weekly samples taken during the period 2007-2010 was coordinated with the parallel program at the Norwegian Arctic monitoring site (Zeppelin mountain, Ny-Ålesund, Svalbard) in terms of priority compounds, sampling schedule as well as analytical methods. The POP concentration levels found in Antarctica were considerably lower than Arctic atmospheric background concentrations. Similar to observations for Arctic samples, HCB is the predominant POP compound, with levels of around 22 pg m-3 throughout the entire monitoring period. In general, the following concentration distribution was found for the Troll samples analyzed: HCB > Sum HCH > Sum PCB > Sum DDT > Sum chlordanes. Atmospheric long-range transport was identified as a major contamination source for POPs in Antarctic environments. Several long-range transport events with elevated levels of pesticides and/or compounds with industrial sources were identified based on retroplume calculations with a Lagrangian particle dispersion model (FLEXPART).

Noise study of all-normal dispersion supercontinuum sources for potential application in optical coherence tomography

NASA Astrophysics Data System (ADS)

Gonzalo, I. B.; Engelsholm, R. D.; Bang, O.

2018-03-01

Commercially available silica-fiber-based and ultra-broadband supercontinuum (SC) sources are typically generated by pumping close to the zero-dispersion wavelength (ZDW) of a photonic crystal fiber (PCF), using high-power picosecond or nanosecond laser pulses. Despite the extremely broad bandwidths, such sources are characterized by large intensity fluctuations, limiting their performance for applications in imaging such as optical coherence tomography (OCT). An approach to eliminate the influence of noise sensitive effects is to use a so-called all-normal dispersion (ANDi) fiber, in which the dispersion is normal for all the wavelengths of interest. Pumping these types of fibers with short enough femtosecond pulses allows to suppress stimulated Raman scattering (SRS), which is known to be as noisy process as modulation instability (MI), and coherent SC is generated through self-phase modulation (SPM) and optical wave breaking (OWB). In this study, we show the importance of the pump laser and fiber parameters in the design of low-noise ANDi based SC sources, for application in OCT. We numerically investigate the pulse-to-pulse fluctuations of the SC, calculating the relative intensity noise (RIN) as a function of the pump pulse duration and fiber length. Furthermore, we experimentally demonstrate the role of the fiber length on the RIN of the ANDi SC, validating the results calculated numerically. In the end, we compare the RIN of a commercial SC source based on MI and the ANDi SC source developed here, which shows better noise performance when it is carefully designed.

Locating an atmospheric contamination source using slow manifolds

NASA Astrophysics Data System (ADS)

Tang, Wenbo; Haller, George; Baik, Jong-Jin; Ryu, Young-Hee

2009-04-01

Finite-size particle motion in fluids obeys the Maxey-Riley equations, which become singular in the limit of infinitesimally small particle size. Because of this singularity, finding the source of a dispersed set of small particles is a numerically ill-posed problem that leads to exponential blowup. Here we use recent results on the existence of a slow manifold in the Maxey-Riley equations to overcome this difficulty in source inversion. Specifically, we locate the source of particles by projecting their dispersed positions on a time-varying slow manifold, and by advecting them on the manifold in backward time. We use this technique to locate the source of a hypothetical anthrax release in an unsteady three-dimensional atmospheric wind field in an urban street canyon.

An End-to-End Model of Plant Pheromone Channel for Long Range Molecular Communication.

PubMed

Unluturk, Bige D; Akyildiz, Ian F

2017-01-01

A new track in molecular communication is using pheromones which can scale up the range of diffusion-based communication from μm meters to meters and enable new applications requiring long range. Pheromone communication is the emission of molecules in the air which trigger behavioral or physiological responses in receiving organisms. The objective of this paper is to introduce a new end-to-end model which incorporates pheromone behavior with communication theory for plants. The proposed model includes both the transmission and reception processes as well as the propagation channel. The transmission process is the emission of pheromones from the leaves of plants. The dispersion of pheromones by the flow of wind constitutes the propagation process. The reception process is the sensing of pheromones by the pheromone receptors of plants. The major difference of pheromone communication from other molecular communication techniques is the dispersion channel acting under the laws of turbulent diffusion. In this paper, the pheromone channel is modeled as a Gaussian puff, i.e., a cloud of pheromone released instantaneously from the source whose dispersion follows a Gaussian distribution. Numerical results on the performance of the overall end-to-end pheromone channel in terms of normalized gain and delay are provided.

An improved numerical method for the kernel density functional estimation of disperse flow

NASA Astrophysics Data System (ADS)

Smith, Timothy; Ranjan, Reetesh; Pantano, Carlos

2014-11-01

We present an improved numerical method to solve the transport equation for the one-point particle density function (pdf), which can be used to model disperse flows. The transport equation, a hyperbolic partial differential equation (PDE) with a source term, is derived from the Lagrangian equations for a dilute particle system by treating position and velocity as state-space variables. The method approximates the pdf by a discrete mixture of kernel density functions (KDFs) with space and time varying parameters and performs a global Rayleigh-Ritz like least-square minimization on the state-space of velocity. Such an approximation leads to a hyperbolic system of PDEs for the KDF parameters that cannot be written completely in conservation form. This system is solved using a numerical method that is path-consistent, according to the theory of non-conservative hyperbolic equations. The resulting formulation is a Roe-like update that utilizes the local eigensystem information of the linearized system of PDEs. We will present the formulation of the base method, its higher-order extension and further regularization to demonstrate that the method can predict statistics of disperse flows in an accurate, consistent and efficient manner. This project was funded by NSF Project NSF-DMS 1318161.

Development of advanced image analysis techniques for the in situ characterization of multiphase dispersions occurring in bioreactors.

PubMed

Galindo, Enrique; Larralde-Corona, C Patricia; Brito, Teresa; Córdova-Aguilar, Ma Soledad; Taboada, Blanca; Vega-Alvarado, Leticia; Corkidi, Gabriel

2005-03-30

Fermentation bioprocesses typically involve two liquid phases (i.e. water and organic compounds) and one gas phase (air), together with suspended solids (i.e. biomass), which are the components to be dispersed. Characterization of multiphase dispersions is required as it determines mass transfer efficiency and bioreactor homogeneity. It is also needed for the appropriate design of contacting equipment, helping in establishing optimum operational conditions. This work describes the development of image analysis based techniques with advantages (in terms of data acquisition and processing), for the characterization of oil drops and bubble diameters in complex simulated fermentation broths. The system consists of fully digital acquisition of in situ images obtained from the inside of a mixing tank using a CCD camera synchronized with a stroboscopic light source, which are processed with a versatile commercial software. To improve the automation of particle recognition and counting, the Hough transform (HT) was used, so bubbles and oil drops were automatically detected and the processing time was reduced by 55% without losing accuracy with respect to a fully manual analysis. The system has been used for the detailed characterization of a number of operational conditions, including oil content, biomass morphology, presence of surfactants (such as proteins) and viscosity of the aqueous phase.

High-performance dispersive Raman and absorption spectroscopy as tools for drug identification

NASA Astrophysics Data System (ADS)

Pawluczyk, Olga; Andrey, Sam; Nogas, Paul; Roy, Andrew; Pawluczyk, Romuald

2009-02-01

Due to increasing availability of pharmaceuticals from many sources, a need is growing to quickly and efficiently analyze substances in terms of the consistency and accuracy of their chemical composition. Differences in chemical composition occur at very low concentrations, so that highly sensitive analytical methods become crucial. Recent progress in dispersive spectroscopy with the use of 2-dimensional detector arrays, permits for signal integration along a long (up to 12 mm long) entrance slit of a spectrometer, thereby increasing signal to noise ratio and improving the ability to detect small concentration changes. This is achieved with a non-scanning, non-destructive system. Two different methods using P&P Optica high performance spectrometers were used. High performance optical dispersion Raman and high performance optical absorption spectroscopy were employed to differentiate various acetaminophen-containing drugs, such as Tylenol and other generic brands, which differ in their ingredients. A 785 nm excitation wavelength was used in Raman measurements and strong Raman signals were observed in the spectral range 300-1800 cm-1. Measurements with the absorption spectrometer were performed in the wavelength range 620-1020 nm. Both Raman and absorption techniques used transmission light spectrometers with volume phase holographic gratings and provided sufficient spectral differences, often structural, allowing for drug differentiation.

The evolution of dispersal in a Levins' type metapopulation model.

PubMed

Jansen, Vincent A A; Vitalis, Renaud

2007-10-01

We study the evolution of the dispersal rate in a metapopulation model with extinction and colonization dynamics, akin to the model as originally described by Levins. To do so we extend the metapopulation model with a description of the within patch dynamics. By means of a separation of time scales we analytically derive a fitness expression from first principles for this model. The fitness function can be written as an inclusive fitness equation (Hamilton's rule). By recasting this equation in a form that emphasizes the effects of competition we show the effect of the local competition and the local population size on the evolution of dispersal. We find that the evolution of dispersal cannot be easily interpreted in terms of avoidance of kin competition, but rather that increased dispersal reduces the competitive ability. Our model also yields a testable prediction in term of relatedness and life-history parameters.

A long-term evaluation of applied nucleation as a strategy to facilitate forest restoration.

PubMed

Corbin, Jeffrey D; Robinson, George R; Hafkemeyer, Lauren M; Handel, Steven N

2016-01-01

Applied nucleation is a restoration technique that seeks to facilitate woody-plant establishment by attracting birds or other animals that may introduce seeds of dispersal-limited species. In 1991, an experimental test of applied nucleation was initiated in an abandoned landfill in New Jersey, USA. Trees and shrubs were planted into 16 10 x 10 m plots, covering < 3% of the 6-ha site. In 2010-2011, we sampled the plant community to test the impact of the treatments on forest cover and plant biodiversity. Site-wide forest cover increased substantially in the 19 years since planting from none to 59%. The original planted plots had significantly higher stem density, particularly of bird-dispersed species, than unplanted areas. Species composition outside the planted plots was dominated by the wind-dispersed Fraxinus americana and several small-seeded bird-dispersed species, but there were few species indicative of later successional stages. The expected model of successional development via the nucleation model that rates of colonization would be highest near plantings and that forest cover would spread outward from established clusters was not supported after this time span. Given the site's isolation from potential sources of woody propagules, the experimental treatments may not have been enough to overcome many species' dispersal limitation. Regardless of the mechanism, however, the treatments transformed the once essentially treeless site into a densely wooded habitat, and did so at a rate faster than other descriptions of reforestation following disturbances or land-use changes in the region. Despite the relatively low species richness of the community, this experiment demonstrated that reforestation of even severely degraded habitat can be achieved with minimal management after site preparation and cluster plantings.

Dispersion Distance and the Matter Distribution of the Universe in Dispersion Space.

PubMed

Masui, Kiyoshi Wesley; Sigurdson, Kris

2015-09-18

We propose that "standard pings," brief broadband radio impulses, can be used to study the three-dimensional clustering of matter in the Universe even in the absence of redshift information. The dispersion of radio waves as they travel through the intervening plasma can, like redshift, be used as a cosmological distance measure. Because of inhomogeneities in the electron density along the line of sight, dispersion is an imperfect proxy for radial distance and we show that this leads to calculable dispersion-space distortions in the apparent clustering of sources. Fast radio bursts (FRBs) are a new class of radio transients that are the prototypical standard ping and, due to their high observed dispersion, have been interpreted as originating at cosmological distances. The rate of fast radio bursts has been estimated to be several thousand over the whole sky per day and, if cosmological, the sources of these events should trace the large-scale structure of the Universe. We calculate the dispersion-space power spectra for a simple model where electrons and FRBs are biased tracers of the large-scale structure of the Universe, and we show that the clustering signal could be measured using as few as 10 000 events. Such a survey is in line with what may be achieved with upcoming wide-field radio telescopes.

Influence of prey dispersion on territory and group size of African lions: a test of the resource dispersion hypothesis.

PubMed

Valeix, Marion; Loveridge, Andrew J; MacDonald, David W

2012-11-01

Empirical tests of the resource dispersion hypothesis (RDH), a theory to explain group living based on resource heterogeneity, have been complicated by the fact that resource patch dispersion and richness have proved difficult to define and measure in natural systems. Here, we studied the ecology of African lions Panthera leo in Hwange National Park, Zimbabwe, where waterholes are prey hotspots, and where dispersion of water sources and abundance of prey at these water sources are quantifiable. We combined a 10-year data set from GPS-collared lions for which information of group composition was available concurrently with data for herbivore abundance at waterholes. The distance between two neighboring waterholes was a strong determinant of lion home range size, which provides strong support for the RDH prediction that territory size increases as resource patches are more dispersed in the landscape. The mean number of herbivore herds using a waterhole, a good proxy of patch richness, determined the maximum lion group biomass an area can support. This finding suggests that patch richness sets a maximum ceiling on lion group size. This study demonstrates that landscape ecology is a major driver of ranging behavior and suggests that aspects of resource dispersion limit group sizes.

Dispersion Distance and the Matter Distribution of the Universe in Dispersion Space

NASA Astrophysics Data System (ADS)

Masui, Kiyoshi Wesley; Sigurdson, Kris

2015-09-01

We propose that "standard pings," brief broadband radio impulses, can be used to study the three-dimensional clustering of matter in the Universe even in the absence of redshift information. The dispersion of radio waves as they travel through the intervening plasma can, like redshift, be used as a cosmological distance measure. Because of inhomogeneities in the electron density along the line of sight, dispersion is an imperfect proxy for radial distance and we show that this leads to calculable dispersion-space distortions in the apparent clustering of sources. Fast radio bursts (FRBs) are a new class of radio transients that are the prototypical standard ping and, due to their high observed dispersion, have been interpreted as originating at cosmological distances. The rate of fast radio bursts has been estimated to be several thousand over the whole sky per day and, if cosmological, the sources of these events should trace the large-scale structure of the Universe. We calculate the dispersion-space power spectra for a simple model where electrons and FRBs are biased tracers of the large-scale structure of the Universe, and we show that the clustering signal could be measured using as few as 10 000 events. Such a survey is in line with what may be achieved with upcoming wide-field radio telescopes.

Integration of AERMOD into EDMS

DOT National Transportation Integrated Search

2003-06-22

The Federal Aviation Administration (FAA) requires the use of the Emissions and : Dispersion Modeling System (EDMS) for air quality analysis involving aviation sources. : Dispersion in EDMS has previously been computed by CALINE3 and PAL2. With the :...

Plasmon dispersion in a multilayer solid torus in terms of three-term vector recurrence relations and matrix continued fractions

DOE PAGES

Garapati, K. V.; Bagherian, M.; Passian, A.; ...

2018-01-03

Toroidal confinement, which has played a crucial role in magnetized plasmas and Tokamak physics, is emerging as an effective means to obtain useful electronic and optical response in solids. In particular, excitation of surface plasmons in metal nanorings by photons or electrons finds important applications due to the engendered field distribution and electromagnetic energy confinement. However, in contrast to the case of a plasma, often the solid nanorings are multilayered and/or embedded in a medium. The non-simply connected geometry of the torus results in surface modes that are not linearly independent. A three-term difference equation was recently shown to arisemore » when seeking the nonretarded plasmon dispersion relations for a stratified solid torus (Garapati et al 2017 Phys. Rev. B 95 165422). The reported generalized plasmon dispersion relations are here investigated in terms of the involved matrix continued fractions and their convergence properties including the determinant forms of the dispersion relations obtained for computing the plasmon eigenmodes. We also present the intricacies of the derivation and properties of the Green's function employed to solve the three term amplitude equation that determines the response of the toroidal structure to arbitrary external excitations.« less

Plasmon dispersion in a multilayer solid torus in terms of three-term vector recurrence relations and matrix continued fractions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Garapati, K. V.; Bagherian, M.; Passian, A.

Toroidal confinement, which has played a crucial role in magnetized plasmas and Tokamak physics, is emerging as an effective means to obtain useful electronic and optical response in solids. In particular, excitation of surface plasmons in metal nanorings by photons or electrons finds important applications due to the engendered field distribution and electromagnetic energy confinement. However, in contrast to the case of a plasma, often the solid nanorings are multilayered and/or embedded in a medium. The non-simply connected geometry of the torus results in surface modes that are not linearly independent. A three-term difference equation was recently shown to arisemore » when seeking the nonretarded plasmon dispersion relations for a stratified solid torus (Garapati et al 2017 Phys. Rev. B 95 165422). The reported generalized plasmon dispersion relations are here investigated in terms of the involved matrix continued fractions and their convergence properties including the determinant forms of the dispersion relations obtained for computing the plasmon eigenmodes. We also present the intricacies of the derivation and properties of the Green's function employed to solve the three term amplitude equation that determines the response of the toroidal structure to arbitrary external excitations.« less

Genetic diversity of dispersed seeds is highly variable among leks of the long-wattled umbrellabird

NASA Astrophysics Data System (ADS)

Ottewell, Kym; Browne, Luke; Cabrera, Domingo; Olivo, Jorge; Karubian, Jordan

2018-01-01

Frugivorous animals frequently generate clumped distributions of seeds away from source trees, but genetic consequences of this phenomenon remain poorly resolved. Seed dispersal of the palm Oenocarpus bataua by long-wattled umbrellabirds Cephalopterus penduliger generates high seed densities in leks (i.e., multi-male display sites), providing a suitable venue to investigate how dispersal by this frugivore may influence seed source diversity and genetic structure at local and landscape levels. We found moderate levels of maternal seed source diversity in primary seed rain across five leks in northwest Ecuador (unweighted mean alpha diversity α = 9.52, weighted mean αr = 3.52), with considerable variation among leks (αr range: 1.81-24.55). Qualitatively similar findings were obtained for allelic diversity and heterozygosity. Higher densities of O. bataua adults around leks were associated with higher values of αr and heterozygosity (non-significant trends) and allelic diversity (significant correlation). Seed source overlap between different leks was not common but did occur at low frequency, providing evidence for long-distance seed dispersal by umbrellabirds into leks. Our findings are consistent with the idea that seed pool diversity within leks may be shaped by the interaction between density of local trees, which can vary considerably between leks, and umbrellabird foraging ecology, particularly a lack of territorial defense of fruiting trees. Taken as a whole, this work adds to our growing appreciation of the ways resource distribution and associated frugivore foraging behaviors mechanistically shape seed dispersal outcomes and the distribution of plant genotypes across the landscape.

Connectivity and propagule sources composition drive ditch plant metacommunity structure

NASA Astrophysics Data System (ADS)

Favre-Bac, Lisa; Ernoult, Aude; Mony, Cendrine; Rantier, Yann; Nabucet, Jean; Burel, Françoise

2014-11-01

The fragmentation of agricultural landscapes has a major impact on biodiversity. In addition to habitat loss, dispersal limitation increasingly appears as a significant driver of biodiversity decline. Landscape linear elements, like ditches, may reduce the negative impacts of fragmentation by enhancing connectivity for many organisms, in addition to providing refuge habitats. To characterize these effects, we investigated the respective roles of propagule source composition and connectivity at the landscape scale on hydrochorous and non-hydrochorous ditch bank plant metacommunities. Twenty-seven square sites (0.5 km2 each) were selected in an agricultural lowland of northern France. At each site, plant communities were sampled on nine ditch banks (totaling 243 ditches). Variables characterizing propagule sources composition and connectivity were calculated for landscape mosaic and ditch network models. The landscape mosaic influenced only non-hydrochorous species, while the ditch network impacted both hydrochorous and non-hydrochorous species. Non-hydrochorous metacommunities were dependent on a large set of land-use elements, either within the landscape mosaic or adjacent to the ditch network, whereas hydrochorous plant metacommunities were only impacted by the presence of ditches adjacent to crops and roads. Ditch network connectivity also influenced both hydrochorous and non-hydrochorous ditch bank plant metacommunity structure, suggesting that beyond favoring hydrochory, ditches may also enhance plant dispersal by acting on other dispersal vectors. Increasing propagule sources heterogeneity and connectivity appeared to decrease within-metacommunity similarity within landscapes. Altogether, our results suggest that the ditch network's composition and configuration impacts plant metacommunity structure by affecting propagule dispersal possibilities, with contrasted consequences depending on species' dispersal vectors.

Soliton solutions to the fifth-order Korteweg-de Vries equation and their applications to surface and internal water waves

NASA Astrophysics Data System (ADS)

Khusnutdinova, K. R.; Stepanyants, Y. A.; Tranter, M. R.

2018-02-01

We study solitary wave solutions of the fifth-order Korteweg-de Vries equation which contains, besides the traditional quadratic nonlinearity and third-order dispersion, additional terms including cubic nonlinearity and fifth order linear dispersion, as well as two nonlinear dispersive terms. An exact solitary wave solution to this equation is derived, and the dependence of its amplitude, width, and speed on the parameters of the governing equation is studied. It is shown that the derived solution can represent either an embedded or regular soliton depending on the equation parameters. The nonlinear dispersive terms can drastically influence the existence of solitary waves, their nature (regular or embedded), profile, polarity, and stability with respect to small perturbations. We show, in particular, that in some cases embedded solitons can be stable even with respect to interactions with regular solitons. The results obtained are applicable to surface and internal waves in fluids, as well as to waves in other media (plasma, solid waveguides, elastic media with microstructure, etc.).

APPROXIMATION OF ROTATIONAL STRENGTHS FROM MOLAR ROTATION DATA AND GENERATION OF ROTATORY DISPERSION CURVES FOR D-CAMPHOR-10-SULFONATE

PubMed Central

Urry, Dan W.

1969-01-01

Starting with the expression for optical rotatory dispersion in the absorption region that was arrived at by Condon, two series were considered for the purpose of achieving the experimentally observed, steeper wavelength dependence in the absorption region while retaining the established 1/λ2 law in regions removed from absorption. The first two terms of one series in which the second term exhibits a 1/λ6 wavelength dependence were found to calculate satisfactorily the optical rotatory dispersion curve of d-camphor-10-sulfonate from 400 mμ to 190 mμ when only three bands were considered. Evaluated at the extrema, the two-term expression can be approximated by a simple equation which allows calculation of the rotational strength of a nonoverlapping band by using only the wavelength and molar rotation of the extrema and the index of refraction of the solution. The rotational strengths calculated from optical rotatory dispersion data in this manner closely agree with those calculated from corresponding circular dichroism data. Thus when position and magnitude of rotatory dispersion extrema alone are reported for carbonyls, it is suggested that such published data may be converted to approximate rotational strengths. PMID:5257123

The Icelandic volcanological data node and data service

NASA Astrophysics Data System (ADS)

Vogfjord, Kristin; Sigmundsson, Freysteinn; Futurevolc Team

2013-04-01

Through funding from the European FP7 programme, the International Civil Aviation Authority (ICAO), as well as the local Icelandic government and RANNÍS research fund, the establishment of the Icelandic volcano observatory (VO) as a cross-disciplinary, international volcanological data node and data service is starting to materialize. At the core of this entity is the close collaboration between the Icelandic Meteorological Office (IMO), a natural hazard monitoring and research institution, and researchers at the Earth Science Institute of the University of Iceland, ensuring long-term sustainable access to research quality data and products. Existing Icelandic Earth science monitoring and research infrastructures are being prepared for integration with the European EPOS infrastructure. Because the VO is located at a Met Office, this infrastructure also includes meteorological infrastructures relevant to volcanology. Furthermore, the FP7 supersite project, FUTUREVOLC cuts across disciplines to bring together European researchers from Earth science, atmospheric science, remote sensing and space science focussed on combined processing of the different data sources and results to generate a multiparametric volcano monitoring and early warning system. Integration with atmospheric and space science is to meet the need for better estimates of the volcanic eruption source term and dispersion, which depend not only on the magma flow rate and composition, but also on atmosphere-plume interaction and dispersion. This should lead to better estimates of distribution of ash in the atmosphere. FUTUREVOLC will significantly expand the existing Icelandic EPOS infrastructure to an even more multidisciplinary volcanological infrastructure. A central and sustainable part of the project is the establishment of a research-quality data centre at the VO. This data centre will be able to serve as a volcanological data node within EPOS, making multidisciplinary data accessible to scientists and stakeholders, and enabling the generation of products and services useful for civil protection, societal infrastructure and international aviation. The 2010 Eyjafjallajökull eruption demonstrated that eruption and dispersion of volcanic ash in the atmosphere can have far-reaching detrimental effects on aviation. The aviation community is therefore an important stakeholder in volcano monitoring, but interaction between the two communities is not well established. Traditionally Met Offices provide services vital to aviation safety and therefore have strong ties to the aviation community, with internationally established protocols for interaction. The co-habitation of a Met Office with a VO establishes a firm connection between these communities and allows adaptation of already established protocols to facilitate access to information and development of services for aviation, as well as sources of support for the VO.

Sensitivity of predicted bioaerosol exposure from open windrow composting facilities to ADMS dispersion model parameters.

PubMed

Douglas, P; Tyrrel, S F; Kinnersley, R P; Whelan, M; Longhurst, P J; Walsh, K; Pollard, S J T; Drew, G H

2016-12-15

Bioaerosols are released in elevated quantities from composting facilities and are associated with negative health effects, although dose-response relationships are not well understood, and require improved exposure classification. Dispersion modelling has great potential to improve exposure classification, but has not yet been extensively used or validated in this context. We present a sensitivity analysis of the ADMS dispersion model specific to input parameter ranges relevant to bioaerosol emissions from open windrow composting. This analysis provides an aid for model calibration by prioritising parameter adjustment and targeting independent parameter estimation. Results showed that predicted exposure was most sensitive to the wet and dry deposition modules and the majority of parameters relating to emission source characteristics, including pollutant emission velocity, source geometry and source height. This research improves understanding of the accuracy of model input data required to provide more reliable exposure predictions. Copyright © 2016. Published by Elsevier Ltd.

Effects of natal departure and water level on survival of juvenile snail kites (Rostrhamus sociabilis) in Florida

USGS Publications Warehouse

Dreitz, V.J.; Kitchens, W.M.; DeAngelis, D.L.

2004-01-01

Survival rate from fledging to breeding, or juvenile survival, is an important source of variation in lifetime reproductive success in birds. Therefore, determining the relationship between juvenile survival and environmental factors is essential to understanding fitness consequences of reproduction in many populations. With increases in density of individuals and depletion of food resources, quality of most habitats deteriorates during the breeding season. Individuals respond by dispersing in search of food resources. Therefore, to understand the influence of environmental factors on juvenile survival, it is also necessary to know how natal dispersal influences survival of juveniles. We examined effects of various environmental factors and natal dispersal behavior on juvenile survival of endangered Snail Kites (Rostrhamus sociabilis) in central and southern Florida, using a generalized estimating equations (GEEs) approach and model selection criteria. Our results suggested yearly effects and an influence of age and monthly minimum hydrologic levels on juvenile Snail Kite survival. Yearly variation in juvenile survival has been reported by other studies, and other reproductive components of Snail Kites also exhibit such variation. Age differences in juvenile survival have also been seen in other species during the juvenile period. Our results demonstrate a positive relationship between water levels and juvenile survival. We suggest that this is not a direct linear relationship, such that higher water means higher juvenile survival. The juvenile period is concurrent with onset of the wet season in the ecosystem we studied, and rainfall increases as juveniles age. For management purposes, we believe that inferences suggesting increasing water levels during the fledging period will increase juvenile survival may have short-term benefits but lead to long-term declines in prey abundance and possibly wetland vegetation structure.

Status of wind-energy conversion

NASA Technical Reports Server (NTRS)

Thomas, R. L.; Savino, J. M.

1973-01-01

The utilization of wind energy is technically feasible as evidenced by the many past demonstrations of wind generators. The cost of energy from the wind has been high compared to fossil fuel systems; a sustained development effort is needed to obtain economical systems. The variability of the wind makes it an unreliable source on a short term basis. However, the effects of this variability can be reduced by storage systems or connecting wind generators to: (1) fossil fuel systems; (2) hydroelectric systems; or (3) dispersing them throughout a large grid network. Wind energy appears to have the potential to meet a significant amount of our energy needs.

Power quality and protection of electric distribution systems with small, dispersed generation devices

NASA Astrophysics Data System (ADS)

Rizy, D. T.; Jewell, W. T.

1984-10-01

There are several operational problems associated with the connection of small power sources, such as wind turbines and photovoltaic (PV) arrays, to an electric distribution system. In one study the harmonic distortion produced by a subdivision of PV arrays connected through line-commutated inverters was simulated. A second simulation study evaluated protection problems associated with the operation of dispersed ac generators. The purpose of these studies was to examine the adequacy of the electric utility industry's traditional practices and hardware for the operation of dispersed power sources. The results of these simulation studies are discussed and recommendations are given for hardware and system operation needed for accommodating this new technology.

Microcomputer pollution model for civilian airports and Air Force bases. Model description

DOE Office of Scientific and Technical Information (OSTI.GOV)

Segal, H.M.; Hamilton, P.L.

1988-08-01

This is one of three reports describing the Emissions and Dispersion Modeling System (EDMS). EDMS is a complex source emissions/dispersion model for use at civilian airports and Air Force bases. It operates in both a refined and a screening mode and is programmed for an IBM-XT (or compatible) computer. This report--MODEL DESCRIPTION--provides the technical description of the model. It first identifies the key design features of both the emissions (EMISSMOD) and dispersion (GIMM) portions of EDMS. It then describes the type of meteorological information the dispersion model can accept and identifies the manner in which it preprocesses National Climatic Centermore » (NCC) data prior to a refined-model run. The report presents the results of running EDMS on a number of different microcomputers and compares EDMS results with those of comparable models. The appendices elaborate on the information noted above and list the source code.« less

Effects of La2O3 content and particle size on the long-term stability and thermal cycling property of La2O3-dispersed SUS430 alloys for SOFC interconnect materials

NASA Astrophysics Data System (ADS)

Lee, Jung-Won; Mehran, Muhammad Taqi; Song, Rak-Hyun; Lee, Seung-Bok; Lee, Jong-Won; Lim, Tak-Hyoung; Park, Seok-Joo; Hong, Jong-Eun; Shim, Joon-Hyung

2017-11-01

We developed oxide-dispersed alloys as interconnect materials for a solid oxide fuel cell by adding La2O3 to SUS430 ferritic steels. For this purpose, we prepared two types of La2O3 with different particle sizes and added different amounts of La2O3 to SUS430 powder. Then, we mixed the powders using a high energy ball mill, so that nano-sized as well as micro-sized oxide particles were able to mix uniformly with the SUS430 powders. After preparing hexahedral green samples using uni-axial and cold isostatic presses, we were finally able to obtain oxide-dispersed alloys having high relative densities after firing at 1,400 °C under hydrogen atmosphere. The nano-sized La2O3 dispersed alloys showed properties superior to those of micro-sized dispersed alloys in terms of long-term stability and thermal cycling. Moreover, we determined the optimum amounts of added La2O3. Finally we were able to develop a new oxide-dispersed alloy showing excellent properties of low area specific resistance (16.23 mΩ cm2) after 1000 h at 800 °C, and no degradation after 10 iterations of thermal cycling under oxidizing atmosphere.

Is thermal dispersivity significant for the use of heat as a tracer?

NASA Astrophysics Data System (ADS)

Rau, G. C.; Andersen, M. S.; Acworth, I.

2011-12-01

Heat profiles are regularly used to estimate sediment thermal parameters and to quantify vertical water flow velocity in fully saturated porous media. However, it has been pointed out by several authors that there is disagreement regarding the use of thermal dispersivity in heat transport models [e.g. Anderson, 2005]. Some researchers argue that this term should be treated analogous to solute transport [e.g. de Marsily, 1986], whilst others state that because heat diffusion is much faster than solute diffusion the dispersivity term can be neglected [e.g. Ingebritsen and Sanford, 1998]. This issue has never been properly addressed experimentally for environmentally relevant conditions. In order to address this question a hydraulic laboratory experiment was designed to investigate heat transport for different steady-state uniform flow velocities in the Darcy range (between 0 and 100 m/d) through homogeneous sand. For each flow velocity a point heat source at the center of the tank was instantaneously activated, and the thermal response was measured at 27 different locations using high resolution temperature probes. For the same flow velocities, a solute slug was injected in the center of the tank and the solute slug breakthrough was measured using 3 fluid EC sensors at different distances downstream of the injection point. This enabled direct comparison of solute and heat transport under identical conditions. The recorded temperature time-series data were used to calculate the thermal properties of the sand for conduction only, and estimate water flow velocity and thermal dispersion. The recorded EC time-series data were used to independently estimate water flow velocity but also solute dispersivity. The analytical solution for the solute transport case [Hunt, 1978] was adapted for heat transport and extended to account for slightly non-ideal experiment conditions. Velocity results independently derived from solute and heat show a discrepancy of up to 20%. The reason for this is not clear. Furthermore, the results show that thermal dispersivity can best be approximated with a square dependency on flow velocity. This agrees with earlier experiments in ideal materials by Green et al. [1964] as well as theoretical derivations [Kaviany, 1995]. However, this is in contrast to the linear dispersion model which has been adapted from solute transport and is commonly used in groundwater studies. The experimental results can be visualized in a conceptual plot devised by Bear [1972] for solute dispersion data (Figure 1). From this it becomes clear that the heat and solute transport Peclet numbers differs by several orders of magnitude for the same flow velocity and material because diffusion of heat is much faster than solute diffusion. As a result, the same Darcy flow range covers a different Peclet number range in heat transport and solute transport. This explains the controversy in the hydrologic community regarding the use of thermal dispersivity in transport models. In summary, for this experiment thermal dispersivity can be neglected when thermal Pe < 0.5, but should be considered for Pe > 0.5 with a square dependency on velocity.

Stochastic analysis of concentration field in a wake region.

PubMed

Yassin, Mohamed F; Elmi, Abdirashid A

2011-02-01

Identifying geographic locations in urban areas from which air pollutants enter the atmosphere is one of the most important information needed to develop effective mitigation strategies for pollution control. Stochastic analysis is a powerful tool that can be used for estimating concentration fluctuation in plume dispersion in a wake region around buildings. Only few studies have been devoted to evaluate applications of stochastic analysis to pollutant dispersion in an urban area. This study was designed to investigate the concentration fields in the wake region using obstacle model such as an isolated building model. We measured concentration fluctuations at centerline of various downwind distances from the source, and different heights with the frequency of 1 KHz. Concentration fields were analyzed stochastically, using the probability density functions (pdf). Stochastic analysis was performed on the concentration fluctuation and the pdf of mean concentration, fluctuation intensity, and crosswind mean-plume dispersion. The pdf of the concentration fluctuation data have shown a significant non-Gaussian behavior. The lognormal distribution appeared to be the best fit to the shape of concentration measured in the boundary layer. We observed that the plume dispersion pdf near the source was shorter than the plume dispersion far from the source. Our findings suggest that the use of stochastic technique in complex building environment can be a powerful tool to help understand the distribution and location of air pollutants.

Examination of climatological wind patterns and simulated pollen dispersion in a complex island environment

DOE PAGES

Viner, Brian J.; Arritt, Raymond W.; Westgate, Mark E.

2017-03-29

Complex terrain creates small-scale circulations which affect pollen dispersion but may be missed by meteorological observing networks and coarse-grid meteorological models. On volcanic islands, these circulations result from differing rates of surface heating between land and sea as well as rugged terrain. We simulated the transport of bentgrass, ryegrass, and maize pollen from 30 sources within the agricultural regions of the Hawaiian island Kaua’i during climatological conditions spanning season conditions and the La Niña, El Niño, and neutral phases of the El Niño-Southern Oscillation. Both pollen size and source location had major effects on predicted dispersion over and near themore » island. Three patterns of pollen dispersion were identified in response to prevailing wind conditions: southwest winds transported pollen inland, funneling pollen grains through valleys; east winds transported pollen over the ocean, with dispersive tails for the smallest pollen grains following the mean wind and extending as far as the island of Ni’ihau 35 km away; and northeast winds moved pollen inland counter to the prevailing flow due to a sea breeze circulation that formed over the source region. These results are the first to predict the interactions between complex island terrain and local climatology on grass pollen dispersion. As a result, they demonstrate how numerical modeling can provide guidance for field trials by illustrating the common flow regimes present in complex terrain, allowing field trials to focus on areas where successful sampling is more likely to occur.« less

Examination of climatological wind patterns and simulated pollen dispersion in a complex island environment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Viner, Brian J.; Arritt, Raymond W.; Westgate, Mark E.

Complex terrain creates small-scale circulations which affect pollen dispersion but may be missed by meteorological observing networks and coarse-grid meteorological models. On volcanic islands, these circulations result from differing rates of surface heating between land and sea as well as rugged terrain. We simulated the transport of bentgrass, ryegrass, and maize pollen from 30 sources within the agricultural regions of the Hawaiian island Kaua’i during climatological conditions spanning season conditions and the La Niña, El Niño, and neutral phases of the El Niño-Southern Oscillation. Both pollen size and source location had major effects on predicted dispersion over and near themore » island. Three patterns of pollen dispersion were identified in response to prevailing wind conditions: southwest winds transported pollen inland, funneling pollen grains through valleys; east winds transported pollen over the ocean, with dispersive tails for the smallest pollen grains following the mean wind and extending as far as the island of Ni’ihau 35 km away; and northeast winds moved pollen inland counter to the prevailing flow due to a sea breeze circulation that formed over the source region. These results are the first to predict the interactions between complex island terrain and local climatology on grass pollen dispersion. As a result, they demonstrate how numerical modeling can provide guidance for field trials by illustrating the common flow regimes present in complex terrain, allowing field trials to focus on areas where successful sampling is more likely to occur.« less

Application of the Pseudo Wigner-Ville Distribution to the Measurement of the Dispersion of Lamb Modes in Graphite/Epoxy Plates

NASA Technical Reports Server (NTRS)

Prosser, W. H.; Seale, M. D.; Smith, B. T.

1997-01-01

Acoustic waves propagate in thin plates as guided or Lamb modes. The velocities of these modes are dispersive in that they depend not only on the material elastic properties and density, but also on the frequency. Accurate characterization of Lamb wave dispersion is important in many acoustic based nondestructive evaluation techniques. It is necessary for ultrasonic measurements in thin plates to determine elastic properties and for flaw detection and localization. In acoustic emission (AE) testing, if not taken into account, highly dispersive Lamb mode propagation can lead to large errors in source location. In this study, the pseudo Wigner-Ville distribution (PWVD) was used for measurement of group velocity dispersion of Lamb waves in a unidirectional graphite/epoxy (AS4/3502) laminate. The PWVD is one of a number of transforms which provide a time-frequency representation of a digitized time series. Broad band acoustic waves were generated by a pencil lead fracture (Hsu-Neilsen source) and were detected with broad band ultrasonic transducers. The arrival times for the lowest order symmetric (S(sub 0)) and antisymmetric (A(sub 0)) Lamb modes were determined from measurements of the time at which the respective peak amplitudes occurred in the PWVD. Measurements were made at several source-to-detector distances and a least squares fit used to calculate the velocity. Results are presented for propagation along, and perpendicular to, the fiber direction. Theoretical dispersion curves were also calculated and a comparison between theory and experiment demonstrates good agreement.

Energy-efficient methane production from macroalgal biomass through chemo disperser liquefaction.

PubMed

Tamilarasan, K; Kavitha, S; Rajesh Banu, J; Arulazhagan, P; Yeom, Ick Tae

2017-03-01

In this study, an effort has been made to reduce the energy cost of liquefaction by coupling a mechanical disperser with a chemical (sodium tripolyphosphate). In terms of the cost and specific energy demand of liquefaction, the algal biomass disintegrated at 12,000rpm for 30min, and an STPP dosage of about 0.04g/gCOD was chosen as an optimal parameter. Chemo disperser liquefaction (CDL) was found to be energetically and economically sustainable in terms of liquefaction, methane production, and net profit (15%, 0.14gCOD/gCOD, and 4 USD/Ton of algal biomass) and preferable to disperser liquefaction (DL) (10%, 0.11 gCOD/gCOD, and -475 USD/Ton of algal biomass). Copyright © 2016 Elsevier Ltd. All rights reserved.

Interpretation of magnetotelluric measurements over an electrically dispersive one-dimensional earth

DOE Office of Scientific and Technical Information (OSTI.GOV)

Patella, D.

1987-01-01

Frequency dispersion of electromagnetic parameters of earth materials has been widely documented in recent years. It is claimed that magnetotellurics (MT)may be significantly affected by dispersion. This paper studies the MT plane-wave interpretative problem for a one-dimensional earth characterized by the presence of dispersive layers. The theoretical properties of the MT field under the dispersion hypothesis, and the main features of the dispersion phenomenon are synthetically reviewed. The examination of previously published MT curve responses over some models of dispersive earth section shows that ambiguity can arise when interpreting MT data with no other source of information. Thus it maybemore » almost impossible to distinguish between the response of a dispersive section and an equally probable dispersion-free section. The dispersion magnetotelluric (DMT) method is proposed as a means to resolve the ambiguity. The DMT method is based on the execution, at the same site, of an MT sounding and of an always dispersion-free dc geoelectric deep sounding.« less

A cost-effective method for simulating city-wide air flow and pollutant dispersion at building resolving scale

NASA Astrophysics Data System (ADS)

Berchet, Antoine; Zink, Katrin; Muller, Clive; Oettl, Dietmar; Brunner, Juerg; Emmenegger, Lukas; Brunner, Dominik

2017-06-01

A cost-effective method is presented allowing to simulate the air flow and pollutant dispersion in a whole city over multiple years at the building-resolving scale with hourly time resolution. This combination of high resolution and long time span is critically needed for epidemiological studies and for air pollution control, but still poses a great challenge for current state-of-the-art modelling techniques. The presented method relies on the pre-computation of a discrete set of possible weather situations and corresponding steady-state flow and dispersion patterns. The most suitable situation for any given hour is then selected by matching the simulated wind patterns to meteorological observations in and around the city. The catalogue of pre-computed situations corresponds to different large-scale forcings in terms of wind speed, wind direction and stability. A meteorological model converts these forcings into realistic mesoscale flow patterns accounting for the effects of topography and land-use contrasts in a domain covering the city and its surroundings. These mesoscale patterns serve as boundary conditions for a microscale urban flow model which finally drives a Lagrangian air pollutant dispersion model. The method is demonstrated with the modelling system GRAMM/GRAL v14.8 for two Swiss cities in complex terrain, Zurich and Lausanne. The mesoscale flow patterns in the two regions of interest, dominated by land-lake breezes and driven by the partly steep topography, are well reproduced in the simulations matched to in situ observations. In particular, the combination of wind measurements at different locations around the city appeared to be a robust approach to deduce the stability class for the boundary layer within the city. This information is critical for predicting the temporal variability of pollution concentration within the city, regarding their relationship with the intensity of horizontal and vertical dispersion and of turbulence. In the vicinity of sources, the 5 m resolution chosen in our set-up is not always sufficient to reproduce the very steep concentration gradients, pointing at additional cost optimisations in the method required to make higher resolutions affordable. Nevertheless, the catalogue-based methodology allows reproducing concentration variability very consistently further away from emission sources, hence for most parts of the city.

Time-Frequency Analysis of the Dispersion of Lamb Modes

NASA Technical Reports Server (NTRS)

Prosser, W. H.; Seale, Michael D.; Smith, Barry T.

1999-01-01

Accurate knowledge of the velocity dispersion of Lamb modes is important for ultrasonic nondestructive evaluation methods used in detecting and locating flaws in thin plates and in determining their elastic stiffness coefficients. Lamb mode dispersion is also important in the acoustic emission technique for accurately triangulating the location of emissions in thin plates. In this research, the ability to characterize Lamb mode dispersion through a time-frequency analysis (the pseudo-Wigner-Ville distribution) was demonstrated. A major advantage of time-frequency methods is the ability to analyze acoustic signals containing multiple propagation modes, which overlap and superimpose in the time domain signal. By combining time-frequency analysis with a broadband acoustic excitation source, the dispersion of multiple Lamb modes over a wide frequency range can be determined from as little as a single measurement. In addition, the technique provides a direct measurement of the group velocity dispersion. The technique was first demonstrated in the analysis of a simulated waveform in an aluminum plate in which the Lamb mode dispersion was well known. Portions of the dispersion curves of the AO, A I , So, and S2 Lamb modes were obtained from this one waveform. The technique was also applied for the analysis of experimental waveforms from a unidirectional graphite/epoxy composite plate. Measurements were made both along and perpendicular to the fiber direction. In this case, the signals contained only the lowest order symmetric and antisymmetric modes. A least squares fit of the results from several source to detector distances was used. Theoretical dispersion curves were calculated and are shown to be in good agreement with experimental results.

Effects of a chemical dispersant and crude oil on breeding ducks

USGS Publications Warehouse

Albers, P.H.; Gay, M.L.

1982-01-01

Effects of chemically dispersed crude oil on mallard reproduction. Incubating female mallards were exposed to a water source treated with either Prudhoe Bay crude oil, Corexit 9527, or a combination of oil and dispersant during the first 10 da of development. Used thermocouple probes to monitor incubation temperature. Measured hatching success, incubation temperature, and survival of ducklings to 1 wk of age.

Assessment of spatial discordance of primary and effective seed dispersal of European beech (Fagus sylvatica L.) by ecological and genetic methods.

PubMed

Millerón, M; López de Heredia, U; Lorenzo, Z; Alonso, J; Dounavi, A; Gil, L; Nanos, N

2013-03-01

Spatial discordance between primary and effective dispersal in plant populations indicates that postdispersal processes erase the seed rain signal in recruitment patterns. Five different models were used to test the spatial concordance of the primary and effective dispersal patterns in a European beech (Fagus sylvatica) population from central Spain. An ecological method was based on classical inverse modelling (SSS), using the number of seed/seedlings as input data. Genetic models were based on direct kernel fitting of mother-to-offspring distances estimated by a parentage analysis or were spatially explicit models based on the genotype frequencies of offspring (competing sources model and Moran-Clark's Model). A fully integrated mixed model was based on inverse modelling, but used the number of genotypes as input data (gene shadow model). The potential sources of error and limitations of each seed dispersal estimation method are discussed. The mean dispersal distances for seeds and saplings estimated with these five methods were higher than those obtained by previous estimations for European beech forests. All the methods show strong discordance between primary and effective dispersal kernel parameters, and for dispersal directionality. While seed rain was released mostly under the canopy, saplings were established far from mother trees. This discordant pattern may be the result of the action of secondary dispersal by animals or density-dependent effects; that is, the Janzen-Connell effect. © 2013 Blackwell Publishing Ltd.

Measuring short distance dispersal of Alliaria petiolata and determining potential long distance dispersal mechanisms

PubMed Central

Anderson, Roger C.

2018-01-01

Introduction Alliaria petiolata, an herbaceous plant, has invaded woodlands in North America. Its ecology has been thoroughly studied, but an overlooked aspect of its biology is seed dispersal distances and mechanisms. We measured seed dispersal distances in the field and tested if epizoochory is a potential mechanism for long-distance seed dispersal. Methods Dispersal distances were measured by placing seed traps in a sector design around three seed point sources, which consisted of 15 second-year plants transplanted within a 0.25 m radius circle. Traps were placed at intervals ranging from 0.25–3.25 m from the point source. Traps remained in the field until a majority of seeds were dispersed. Eight probability density functions were fitted to seed trap counts via maximum likelihood. Epizoochory was tested as a potential seed dispersal mechanism for A. petiolata through a combination of field and laboratory experiments. To test if small mammals transport A. petiolata seeds in their fur, experimental blocks were placed around dense A. petiolata patches. Each block contained a mammal inclusion treatment (MIT) and control. The MIT consisted of a wood-frame (31 × 61× 31 cm) covered in wire mesh, except for the two 31 × 31 cm ends, placed over a germination tray filled with potting soil. A pan filled with bait was placed in the center of the tray. The control frame (11 × 31 × 61 cm) was placed over a germination tray and completely covered in wire mesh to exclude animal activity. Treatments were in the field for peak seed dispersal. In March, trays were moved to a greenhouse and A. petiolata seedlings were counted and then compared between treatments. To determine if A. petiolata seeds attach to raccoon (Procyon lotor) and white-tailed deer (Odocoileus virginianus) fur, wet and dry seeds were dropped onto wet and dry fur. Furs were rotated 180 degrees and the seeds that remained attached were counted. To measure seed retention, seeds were dropped on furs and rotated as before, then the furs were agitated for one hour. The seeds retained in the fur were counted. Results For the seed dispersal experiment, the 2Dt function provided the best fit and was the most biologically meaningful. It predicted that seed density rapidly declined with distance from the point source. Mean dispersal distance was 0.52 m and 95% of seeds dispersed within 1.14 m. The epizoochory field experiment showed increased mammal activity and A. petiolata seedlings in germination trays of the MIT compared to control. Laboratory studies showed 3–26% of seeds were attached and retained by raccoon and deer fur. Retention significantly increased if either seed or fur were wet (57–98%). Discussion Without animal seed vectors, most seeds fall within a short distance of the seed source; however, long distance dispersal may be accomplished by epizoochory. Our data are consistent with A. petiolata’s widespread distribution and development of dense clusters of the species in invaded areas. PMID:29576955

Natural age dispersion arising from the analysis of broken crystals. Part I: Theoretical basis and implications for the apatite (U-Th)/He thermochronometer

NASA Astrophysics Data System (ADS)

Brown, Roderick W.; Beucher, Romain; Roper, Steven; Persano, Cristina; Stuart, Fin; Fitzgerald, Paul

2013-12-01

Over the last decade major progress has been made in developing both the theoretical and practical aspects of apatite (U-Th)/He thermochronometry and it is now standard practice, and generally seen as best practice, to analyse single grain aliquots. These individual prismatic crystals are often broken and are fragments of larger crystals that have broken during mineral separation along the weak basal cleavage in apatite. This is clearly indicated by the common occurrence of only 1 or no clear crystal terminations present on separated apatite grains, and evidence of freshly broken ends when grains are viewed using a scanning electron microscope. This matters because if the 4He distribution within the whole grain is not homogeneous, because of partial loss due to thermal diffusion for example, then the fragments will all yield ages different from each other and from the whole grain age. Here we use a numerical model with a finite cylinder geometry to approximate 4He ingrowth and thermal diffusion within hexagonal prismatic apatite crystals. This is used to quantify the amount and patterns of inherent, natural age dispersion that arises from analysing broken crystals. A series of systematic numerical experiments were conducted to explore and quantify the pattern and behaviour of this source of dispersion using a set of 5 simple thermal histories that represent a range of plausible geological scenarios. In addition some more complex numerical experiments were run to investigate the pattern and behaviour of grain dispersion seen in several real data sets. The results indicate that natural dispersion of a set of single fragment ages (defined as the range divided by the mean) arising from fragmentation alone varies from c. 7% even for rapid (c. 10 °C/Ma), monotonic cooling to over 50% for protracted, complex histories that cause significant diffusional loss of 4He. The magnitude of dispersion arising from fragmentation scales with the grain cylindrical radius, and is of a similar magnitude to dispersion expected from differences in absolute grain size alone (spherical equivalent radii of 40-150 μm). This source of dispersion is significant compared with typical analytical uncertainties on individual grain analyses (c. 6%) and standard deviations on multiple grain analyses from a single sample (c. 10-20%). Where there is a significant difference in the U and Th concentration of individual grains (eU), the effect of radiation damage accumulation on 4He diffusivity (assessed using the RDAAM model of Flowers et al. (2009)) is the primary cause of dispersion for samples that have experienced a protracted thermal history, and can cause dispersion in excess of 100% for realistic ranges of eU concentration (i.e. 5-100 ppm). Expected natural dispersion arising from the combined effects of reasonable variations in grain size (radii 40-125 μm), eU concentration (5-150 ppm) and fragmentation would typically exceed 100% for complex thermal histories. In addition to adding a significant component of natural dispersion to analyses, the effect of fragmentation also acts to decouple and corrupt expected correlations between grain ages and absolute grain size and to a lesser extent between grain age and effective uranium concentration (eU). Considering fragmentation explicitly as a source of dispersion and analysing how the different sources of natural dispersion all interact with each other provides a quantitative framework for understanding patterns of dispersion that otherwise appear chaotic. An important outcome of these numerical experiments is that they demonstrate that the pattern of age dispersion arising from fragmentation mimics the pattern of 4He distribution within the whole grains, thus providing an important source of information about the thermal history of the sample. We suggest that if the primary focus of a study is to extract the thermal history information from (U-Th)/He analyses then sampling and analytical strategies should aim to maximise the natural dispersion of grain ages, not minimise it, and should aim to analyse circa 20-30 grains from each sample. The key observations and conclusions drawn here are directly applicable to other thermochronometers, such as the apatite, rutile and titanite U-Pb systems, where the diffusion domain is approximated by the physical grain size.

"Dispersion modeling approaches for near road | Science ...

EPA Pesticide Factsheets

Roadway design and roadside barriers can have significant effects on the dispersion of traffic-generated pollutants, especially in the near-road environment. Dispersion models that can accurately simulate these effects are needed to fully assess these impacts for a variety of applications. For example, such models can be useful for evaluating the mitigation potential of roadside barriers in reducing near-road exposures and their associated adverse health effects. Two databases, a tracer field study and a wind tunnel study, provide measurements used in the development and/or validation of algorithms to simulate dispersion in the presence of noise barriers. The tracer field study was performed in Idaho Falls, ID, USA with a 6-m noise barrier and a finite line source in a variety of atmospheric conditions. The second study was performed in the meteorological wind tunnel at the US EPA and simulated line sources at different distances from a model noise barrier to capture the effect on emissions from individual lanes of traffic. In both cases, velocity and concentration measurements characterized the effect of the barrier on dispersion.This paper presents comparisons with the two datasets of the barrier algorithms implemented in two different dispersion models: US EPA’s R-LINE (a research dispersion modelling tool under development by the US EPA’s Office of Research and Development) and CERC’s ADMS model (ADMS-Urban). In R-LINE the physical features reveal

Scalar Dispersion from Point Sources in a Realistic Urban Environment

NASA Astrophysics Data System (ADS)

Salesky, S.; Giometto, M. G.; Christen, A.; Parlange, M. B.

2016-12-01

Accurate modeling of scalar dispersion within and above urban canopies is critical to properly predict air quality and dispersion (e.g. accidental contaminant release) in urban environments. We perform large eddy simulations (LES) of scalar dispersion from point sources in a typical North American neighborhood using topography and foliage density derived from airborne LIDAR scans with 1 m resolution in Vancouver, BC, Canada. The added drag force due to trees is parameterized in the LES as a function of the leaf area density (LAD) profile. Conversely, drag from buildings is accounted for using a direct forcing approach immersed-boundary method. The scalar advection-diffusion equation is discretized in a finite-volume framework, and accurate mass conservation is enforced through a recently developed Cartesian cut cell method. Simulations are performed with trees for different values of LAD, representative of summer and winter conditions, as well as a case without trees. The effects of varying mean wind direction (derived from observed wind climatologies) on dispersion patterns are also considered. Scalar release locations in the LES are informed by spatially distributed measurements of carbon dioxide concentration; CO2 is used as a tracer for fossil fuel emissions, since source strengths are well-known and the contribution from biological processes in this setting is small (<10%). The effects of leaf area density, source height, and wind direction on scalar statistics including the growth of the mean concentration plume and the fraction that escapes the urban canopy layer will be considered. In a companion study, the presence of trees was found to strongly modify sweep and ejection patterns for the momentum flux; here we consider the related issue of how vegetation influences coherent structures responsible for scalar transport.

Travels of airborne pollen. Final report, 1 Oct 1970--31 Dec 1974

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The following studies were conducted on the transport and dispersion of airborne pollen: (a) Development and evaluation of sampling devices for pollen; (b) development and evaluation techniques for tagging pollen in living plants with dyes and radioisotopes; (c) dispersion and deposition of pollen from known sources of various configurations; (d) effects of forested areas on the removal of pollen from the atmosphere; (e) concentration variations of pollen, natural sources with distance, height, time and other variables; (f) feasibility of predicting ragweed pollen concentrations, unknown sources; (g) measurements on ragweed pollen concentrations in a large source-free area; and (h) comparisons ofmore » the ragweed pollen concentrations before and after ragweed eradication efforts. (GRA)« less

The Importance of Dispersal for Bacterial Community Composition and Functioning

PubMed Central

Lindström, Eva S.; Östman, Örjan

2011-01-01

We conducted a metacommunity experiment to investigate the role of dispersal for bacterial community composition (BCC) and function of freshwater bacteria. Bacteria were dispersed from a common source pool into three different lake communities in their natural lake water. The experiment was conducted in dialysis bags to enable a decoupling between a change in the local environment and dispersal. BCC was determined by terminal restriction fragment length polymorphism (tRFLP) of the 16S rRNA gene. We show that the greatest changes in BCC occurred between 10% and 43% of dispersal of standing stock per day. Functioning, measured as growth rate, was also affected by dispersal in all three communities but the qualitative pattern differed between communities, sometimes showing a hump-shaped relationship to dispersal and sometimes decreasing with increasing dispersal. In all waters, functioning was related to BCC. Our results show that dispersal does affect BCC and functioning but that high dispersal rates are needed. Further, the effect of dispersal on BCC and function seem to depend on the quality of the habitat to which bacteria disperse into. PMID:21998714

Dispersions of Carbon nanotubes in Polymer Matrices

NASA Technical Reports Server (NTRS)

Wise, Kristopher Eric (Inventor); Park, Cheol (Inventor); Siochi, Emilie J. (Inventor); Harrison, Joycelyn S. (Inventor); Lillehei, Peter T. (Inventor); Lowther, Sharon E. (Inventor)

2010-01-01

Dispersions of carbon nanotubes exhibiting long term stability are based on a polymer matrix having moieties therein which are capable of a donor-acceptor complexation with carbon nanotubes. The carbon nanotubes are introduced into the polymer matrix and separated therein by standard means. Nanocomposites produced from these dispersions are useful in the fabrication of structures, e.g., lightweight aerospace structures.

Surveillance system for air pollutants by combination of the decision support system COMPAS and optical remote sensing systems

NASA Astrophysics Data System (ADS)

Flassak, Thomas; de Witt, Helmut; Hahnfeld, Peter; Knaup, Andreas; Kramer, Lothar

1995-09-01

COMPAS is a decision support system designed to assist in the assessment of the consequences of accidental releases of toxic and flammable substances. One of the key elements of COMPAS is a feedback algorithm which allows us to calculate the source term with the aid of concentration measurements. Up to now the feedback technique is applied to concentration measurements done with test tubes or conventional point sensors. In this paper the extension of the actual method is presented which is the combination of COMPAS and an optical remote sensing system like the KAYSER-THREDE K300 FTIR system. Active remote sensing methods based on FTIR are, among other applications, ideal for the so-called fence line monitoring of the diffuse emissions and accidental releases from industrial facilities, since from the FTIR spectra averaged concentration levels along the measurement path can be achieved. The line-averaged concentrations are ideally suited as on-line input for COMPAS' feedback technique. Uncertainties in the assessment of the source term related with both shortcomings of the dispersion model itself and also problems of a feedback strategy based on point measurements are reduced.

Thermal Vapor Deposition and Characterization of Polymer-Ceramic Nanoparticle Thin Films and Capacitors

NASA Astrophysics Data System (ADS)

Iwagoshi, Joel A.

Research on alternative energies has become an area of increased interest due to economic and environmental concerns. Green energy sources, such as ocean, wind, and solar power, are subject to predictable and unpredictable generation intermittencies which cause instability in the electrical grid. This problem could be solved through the use of short term energy storage devices. Capacitors made from composite polymer:nanoparticle thin films have been shown to be an economically viable option. Through thermal vapor deposition, we fabricated dielectric thin films composed of the polymer polyvinylidine fluoride (PVDF) and the ceramic nanoparticle titanium dioxide (TiO2). Fully understanding the deposition process required an investigation of electrode and dielectric film deposition. Film composition can be controlled by the mass ratio of PVDF:TiO2 prior to deposition. An analysis of the relationship between the ratio of PVDF:TiO2 before and after deposition will improve our understanding of this novel deposition method. X-ray photoelectron spectroscopy and energy dispersive x-ray spectroscopy were used to analyze film atomic concentrations. The results indicate a broad distribution of deposited TiO2 concentrations with the highest deposited amount at an initial mass concentration of 17% TiO2. The nanoparticle dispersion throughout the film is analyzed through atomic force microscopy and energy dispersive x-ray spectroscopy. Images from these two techniques confirm uniform TiO2 dispersion with cluster size less than 300 nm. These results, combined with spectroscopic analysis, verify control over the deposition process. Capacitors were fabricated using gold parallel plates with PVDF:TiO 2 dielectrics. These capacitors were analyzed using the atomic force microscope and a capacohmeter. Atomic force microscope images confirm that our gold films are acceptably smooth. Preliminary capacohmeter measurements indicate capacitance values of 6 nF and break down voltages of 2.4 V. Our research on the deposition process will contribute to the understanding of PVDF/TiO2 composite thin films. These results will lead to further investigation of PVDF/TiO2 high density energy storage capacitors. These capacitors can potentially increase the efficiency of alternative energy sources already in use.

Regional source identification using Lagrangian stochastic particle dispersion and HYSPLIT backward-trajectory models.

PubMed

Koracin, Darko; Vellore, Ramesh; Lowenthal, Douglas H; Watson, John G; Koracin, Julide; McCord, Travis; DuBois, David W; Chen, L W Antony; Kumar, Naresh; Knipping, Eladio M; Wheeler, Neil J M; Craig, Kenneth; Reid, Stephen

2011-06-01

The main objective of this study was to investigate the capabilities of the receptor-oriented inverse mode Lagrangian Stochastic Particle Dispersion Model (LSPDM) with the 12-km resolution Mesoscale Model 5 (MM5) wind field input for the assessment of source identification from seven regions impacting two receptors located in the eastern United States. The LSPDM analysis was compared with a standard version of the Hybrid Single-Particle Lagrangian Integrated Trajectory (HYSPLIT) single-particle backward-trajectory analysis using inputs from MM5 and the Eta Data Assimilation System (EDAS) with horizontal grid resolutions of 12 and 80 km, respectively. The analysis included four 7-day summertime events in 2002; residence times in the modeling domain were computed from the inverse LSPDM runs and HYPSLIT-simulated backward trajectories started from receptor-source heights of 100, 500, 1000, 1500, and 3000 m. Statistics were derived using normalized values of LSPDM- and HYSPLIT-predicted residence times versus Community Multiscale Air Quality model-predicted sulfate concentrations used as baseline information. From 40 cases considered, the LSPDM identified first- and second-ranked emission region influences in 37 cases, whereas HYSPLIT-MM5 (HYSPLIT-EDAS) identified the sources in 21 (16) cases. The LSPDM produced a higher overall correlation coefficient (0.89) compared with HYSPLIT (0.55-0.62). The improvement of using the LSPDM is also seen in the overall normalized root mean square error values of 0.17 for LSPDM compared with 0.30-0.32 for HYSPLIT. The HYSPLIT backward trajectories generally tend to underestimate near-receptor sources because of a lack of stochastic dispersion of the backward trajectories and to overestimate distant sources because of a lack of treatment of dispersion. Additionally, the HYSPLIT backward trajectories showed a lack of consistency in the results obtained from different single vertical levels for starting the backward trajectories. To alleviate problems due to selection of a backward-trajectory starting level within a large complex set of 3-dimensional winds, turbulence, and dispersion, results were averaged from all heights, which yielded uniform improvement against all individual cases.

Existence and switching behavior of bright and dark Kerr solitons in whispering-gallery mode resonators with zero group-velocity dispersion

NASA Astrophysics Data System (ADS)

Talla Mbé, Jimmi H.; Milián, Carles; Chembo, Yanne K.

2017-07-01

We use the generalized Lugiato-Lefever model to investigate the phenomenon of Kerr optical frequency comb generation when group-velocity dispersion is null. In that case, the first dispersion term that plays a leading role is third-order dispersion. We show that this term is sufficient to allow for the existence of both bright and dark solitons. We identify the areas in the parameter space where both kind of solitons can be excited inside the resonator. We also unveil a phenomenon of hysteretic switching between these two types of solitons when the power of the pump laser is cyclically varied. Contribution to the Topical Issue "Theory and Applications of the Lugiato-Lefever Equation", edited by Yanne K. Chembo, Damia Gomila, Mustapha Tlidi, Curtis R. Menyuk.

Predicting seed dispersal using a Lagrangian Stochastic Model

NASA Astrophysics Data System (ADS)

Hsieh, C. I.; Chen, C. W.; Su, M. D.

2017-12-01

Migration and expansion of a plant species are determined by longdistance dispersion (LDD). A more sophisticated mechanical dispersion model is needed for mimicking LDD of wind-driven seeds. This study simulated seed dispersion trajectories in canopy turbulence by using the Lagrangian stochastic dispersion model under varying atmospheric stabilities in conjunction with the effects of turbulent kinetic energy dissipation rate intermittency. The effects of friction velocity, seed release height, and seed terminal velocity were also studied. The results showed that both the unstable atmosphere and the inclusion of the dissipation rate intermittency in the model could increase seeds' LDD. The number of seeds that escape the canopy volume by dissipation intermittency is increased under unstable atmospheric conditions. As a result, more seeds can be transported a further distance. When dissipation intermittency is included under astrong unstable atmosphere, the peak location of dispersal kernel tends to be closer to the source. Contrasting this, under both neutral and stable conditions when LDD of both are similar, the peak location will be further away from the source. However higher friction velocity, higher seed release height, and lower seed terminal velocity will all increase the LDD of seeds irregardless of atmospheric conditions. The change of LDD due to change in friction velocity, seed release height, or the seed terminal velocity, would be heightened under unstable conditions

Acoustic Rectification in Dispersive Media

NASA Technical Reports Server (NTRS)

Cantrell, John H.

2008-01-01

It is shown that the shapes of acoustic radiation-induced static strain and displacement pulses (rectified acoustic pulses) are defined locally by the energy density of the generating waveform. Dispersive properties are introduced analytically by assuming that the rectified pulses are functionally dependent on a phase factor that includes both dispersive and nonlinear terms. The dispersion causes an evolutionary change in the shape of the energy density profile that leads to the generation of solitons experimentally observed in fused silica.

Bright, dark and W-shaped solitons with extended nonlinear Schrödinger's equation for odd and even higher-order terms

NASA Astrophysics Data System (ADS)

Bendahmane, Issam; Triki, Houria; Biswas, Anjan; Saleh Alshomrani, Ali; Zhou, Qin; Moshokoa, Seithuti P.; Belic, Milivoj

2018-02-01

We present solitary wave solutions of an extended nonlinear Schrödinger equation with higher-order odd (third-order) and even (fourth-order) terms by using an ansatz method. The including high-order dispersion terms have significant physical applications in fiber optics, the Heisenberg spin chain, and ocean waves. Exact envelope solutions comprise bright, dark and W-shaped solitary waves, illustrating the potentially rich set of solitary wave solutions of the extended model. Furthermore, we investigate the properties of these solitary waves in nonlinear and dispersive media. Moreover, specific constraints on the system parameters for the existence of these structures are discussed exactly. The results show that the higher-order dispersion and nonlinear effects play a crucial role for the formation and properties of propagating waves.

Exact Dispersion Study of an Asymmetric Thin Planar Slab Dielectric Waveguide without Computing {d^2}β/{d{k^2}} Numerically

NASA Astrophysics Data System (ADS)

Raghuwanshi, Sanjeev Kumar; Palodiya, Vikram

2017-08-01

Waveguide dispersion can be tailored but not the material dispersion. Hence, the total dispersion can be shifted at any desired band by adjusting the waveguide dispersion. Waveguide dispersion is proportional to {d^2}β/d{k^2} and need to be computed numerically. In this paper, we have tried to compute analytical expression for {d^2}β/d{k^2} in terms of {d^2}β/d{k^2} accurately with numerical technique, ≈ 10^{-5} decimal point. This constraint sometimes generates the error in calculation of waveguide dispersion. To formulate the problem we will use the graphical method. Our study reveals that we can compute the waveguide dispersion enough accurately for various modes by knowing - β only.

Improving volcanic ash predictions with the HYSPLIT dispersion model by assimilating MODIS satellite retrievals

NASA Astrophysics Data System (ADS)

Chai, Tianfeng; Crawford, Alice; Stunder, Barbara; Pavolonis, Michael J.; Draxler, Roland; Stein, Ariel

2017-02-01

Currently, the National Oceanic and Atmospheric Administration (NOAA) National Weather Service (NWS) runs the HYSPLIT dispersion model with a unit mass release rate to predict the transport and dispersion of volcanic ash. The model predictions provide information for the Volcanic Ash Advisory Centers (VAAC) to issue advisories to meteorological watch offices, area control centers, flight information centers, and others. This research aims to provide quantitative forecasts of ash distributions generated by objectively and optimally estimating the volcanic ash source strengths, vertical distribution, and temporal variations using an observation-modeling inversion technique. In this top-down approach, a cost functional is defined to quantify the differences between the model predictions and the satellite measurements of column-integrated ash concentrations weighted by the model and observation uncertainties. Minimizing this cost functional by adjusting the sources provides the volcanic ash emission estimates. As an example, MODIS (Moderate Resolution Imaging Spectroradiometer) satellite retrievals of the 2008 Kasatochi volcanic ash clouds are used to test the HYSPLIT volcanic ash inverse system. Because the satellite retrievals include the ash cloud top height but not the bottom height, there are different model diagnostic choices for comparing the model results with the observed mass loadings. Three options are presented and tested. Although the emission estimates vary significantly with different options, the subsequent model predictions with the different release estimates all show decent skill when evaluated against the unassimilated satellite observations at later times. Among the three options, integrating over three model layers yields slightly better results than integrating from the surface up to the observed volcanic ash cloud top or using a single model layer. Inverse tests also show that including the ash-free region to constrain the model is not beneficial for the current case. In addition, extra constraints on the source terms can be given by explicitly enforcing no-ash for the atmosphere columns above or below the observed ash cloud top height. However, in this case such extra constraints are not helpful for the inverse modeling. It is also found that simultaneously assimilating observations at different times produces better hindcasts than only assimilating the most recent observations.

A stochastic-advective transport model for NAPL dissolution and degradation in non-uniform flows in porous media

NASA Astrophysics Data System (ADS)

Chan, T. P.; Govindaraju, Rao S.

2006-10-01

Remediation schemes for contaminated sites are often evaluated to assess their potential for source zone reduction of mass, or treatment of the contaminant between the source and a control plane (CP) to achieve regulatory limits. In this study, we utilize a stochastic stream tube model to explain the behavior of breakthrough curves (BTCs) across a CP. At the local scale, mass dissolution at the source is combined with an advection model with first-order decay for the dissolved plume. Field-scale averaging is then employed to account for spatial variation in mass within the source zone, and variation in the velocity field. Under the assumption of instantaneous mass transfer from the source to the moving liquid, semi-analytical expressions for the BTC and temporal moments are developed, followed by derivation of expressions for effective velocity, dispersion, and degradation coefficients using the method of moments. It is found that degradation strongly influences the behavior of moments and the effective parameters. While increased heterogeneity in the velocity field results in increased dispersion, degradation causes the center of mass of the plume to shift to earlier times, and reduces the dispersion of the BTC by lowering the concentrations in the tail. Modified definitions of effective parameters are presented for degrading solutes to account for the normalization constant (zeroth moment) that keeps changing with time or distance to the CP. It is shown that anomalous dispersion can result for high degradation rates combined with wide variation in velocity fluctuations. Implications of model results on estimating cleanup times and fulfillment of regulatory limits are discussed. Relating mass removal at the source to flux reductions past a control plane is confounded by many factors. Increased heterogeneity in velocity fields causes mass fluxes past a control plane to persist, however, aggressive remediation between the source and CP can reduce these fluxes.

Soliton Perturbation Theory for Dispersion-Managed Optical Fibers

NASA Astrophysics Data System (ADS)

Kohl, Russell; Milovic, Daniela; Zerrad, Essaid; Biswas, Anjan

This paper studies the propagation of solitons through optical fibers with dispersion management. The adiabatic variation of the soliton parameters, due to the presence of perturbation terms, is obtained. The dynamics is studied for the case of polarization-preserving fibers, while the types of pulses that are considered here are Gaussian, super-Gaussian and supersech. The perturbation terms that are taken into consideration are both local and nonlocal.

Optimizing pulse compressibility in completely all-fibered Ytterbium chirped pulse amplifiers for in vivo two photon laser scanning microscopy

PubMed Central

Fernández, A.; Grüner-Nielsen, L.; Andreana, M.; Stadler, M.; Kirchberger, S.; Sturtzel, C.; Distel, M.; Zhu, L.; Kautek, W.; Leitgeb, R.; Baltuska, A.; Jespersen, K.; Verhoef, A.

2017-01-01

A simple and completely all-fiber Yb chirped pulse amplifier that uses a dispersion matched fiber stretcher and a spliced-on hollow core photonic bandgap fiber compressor is applied in nonlinear optical microscopy. This stretching-compression approach improves compressibility and helps to maximize the fluorescence signal in two-photon laser scanning microscopy as compared with approaches that use standard single mode fibers as stretcher. We also show that in femtosecond all-fiber systems, compensation of higher order dispersion terms is relevant even for pulses with relatively narrow bandwidths for applications relying on nonlinear optical effects. The completely all-fiber system was applied to image green fluorescent beads, a stained lily-of-the-valley root and rat-tail tendon. We also demonstrated in vivo imaging in zebrafish larvae, where we simultaneously measure second harmonic and fluorescence from two-photon excited red-fluorescent protein. Since the pulses are compressed in a fiber, this source is especially suited for upgrading existing laser scanning (confocal) microscopes with multiphoton imaging capabilities in space restricted settings or for incorporation in endoscope-based microscopy. PMID:28856032

Optimizing pulse compressibility in completely all-fibered Ytterbium chirped pulse amplifiers for in vivo two photon laser scanning microscopy.

PubMed

Fernández, A; Grüner-Nielsen, L; Andreana, M; Stadler, M; Kirchberger, S; Sturtzel, C; Distel, M; Zhu, L; Kautek, W; Leitgeb, R; Baltuska, A; Jespersen, K; Verhoef, A

2017-08-01

A simple and completely all-fiber Yb chirped pulse amplifier that uses a dispersion matched fiber stretcher and a spliced-on hollow core photonic bandgap fiber compressor is applied in nonlinear optical microscopy. This stretching-compression approach improves compressibility and helps to maximize the fluorescence signal in two-photon laser scanning microscopy as compared with approaches that use standard single mode fibers as stretcher. We also show that in femtosecond all-fiber systems, compensation of higher order dispersion terms is relevant even for pulses with relatively narrow bandwidths for applications relying on nonlinear optical effects. The completely all-fiber system was applied to image green fluorescent beads, a stained lily-of-the-valley root and rat-tail tendon. We also demonstrated in vivo imaging in zebrafish larvae, where we simultaneously measure second harmonic and fluorescence from two-photon excited red-fluorescent protein. Since the pulses are compressed in a fiber, this source is especially suited for upgrading existing laser scanning (confocal) microscopes with multiphoton imaging capabilities in space restricted settings or for incorporation in endoscope-based microscopy.

Radiological dose in Muria peninsula from SB-LOCA event

NASA Astrophysics Data System (ADS)

Sunarko; Suud, Zaki

2017-01-01

Dose assessment for accident condition is performed for Muria Peninsula region using source-term from Three-Mile Island unit 2 SB-LOCA accident. Xe-133, Kr-88, 1-131 and Cs-137 isotopes are considered in the calculation. The effluent is assumed to be released from a 50 m stack. Lagrangian particle dispersion method (LPDM) employing non-Gaussian dispersion coefficient in 3-dimensional mass-consistent wind-field is employed to obtain periodic surface-level concentration which is then time-integrated to obtain spatial distribution of ground-level dose. In 1-hour simulation, segmented plumes with 60 seconds duration with a total of 18.000 particles involved. Simulations using 6-hour worst-case meteorological data from Muria peninsula results in a peak external dose of around 1.668 mSv for low scenario and 6.892 mSv for high scenario in dry condition. In wet condition with 5 mm/hour and 10 mm/hour rain for the whole duration of the simulation provides only minor effect to dose. The peak external dose is below the regulatory limit of 50 mSv for effective skin dose from external gamma exposure.

On singular and highly oscillatory properties of the Green function for ship motions

NASA Astrophysics Data System (ADS)

Chen, Xiao-Bo; Xiong Wu, Guo

2001-10-01

The Green function used for analysing ship motions in waves is the velocity potential due to a point source pulsating and advancing at a uniform forward speed. The behaviour of this function is investigated, in particular for the case when the source is located at or close to the free surface. In the far field, the Green function is represented by a single integral along one closed dispersion curve and two open dispersion curves. The single integral along the open dispersion curves is analysed based on the asymptotic expansion of a complex error function. The singular and highly oscillatory behaviour of the Green function is captured, which shows that the Green function oscillates with indefinitely increasing amplitude and indefinitely decreasing wavelength, when a field point approaches the track of the source point at the free surface. This sheds some light on the nature of the difficulties in the numerical methods used for predicting the motion of a ship advancing in waves.

Acoustic emission source localization based on distance domain signal representation

NASA Astrophysics Data System (ADS)

Gawronski, M.; Grabowski, K.; Russek, P.; Staszewski, W. J.; Uhl, T.; Packo, P.

2016-04-01

Acoustic emission is a vital non-destructive testing technique and is widely used in industry for damage detection, localisation and characterization. The latter two aspects are particularly challenging, as AE data are typically noisy. What is more, elastic waves generated by an AE event, propagate through a structural path and are significantly distorted. This effect is particularly prominent for thin elastic plates. In these media the dispersion phenomenon results in severe localisation and characterization issues. Traditional Time Difference of Arrival methods for localisation techniques typically fail when signals are highly dispersive. Hence, algorithms capable of dispersion compensation are sought. This paper presents a method based on the Time - Distance Domain Transform for an accurate AE event localisation. The source localisation is found through a minimization problem. The proposed technique focuses on transforming the time signal to the distance domain response, which would be recorded at the source. Only, basic elastic material properties and plate thickness are used in the approach, avoiding arbitrary parameters tuning.

Time-Frequency Analysis of the Dispersion of Lamb Modes

NASA Technical Reports Server (NTRS)

Prosser, W. H.; Seale, Michael D.; Smith, Barry T.

1999-01-01

Accurate knowledge of the velocity dispersion of Lamb modes is important for ultrasonic nondestructive evaluation methods used in detecting and locating flaws in thin plates and in determining their elastic stiffness coefficients. Lamb mode dispersion is also important in the acoustic emission technique for accurately triangulating the location of emissions in thin plates. In this research, the ability to characterize Lamb mode dispersion through a time-frequency analysis (the pseudo Wigner-Ville distribution) was demonstrated. A major advantage of time-frequency methods is the ability to analyze acoustic signals containing multiple propagation modes, which overlap and superimpose in the time domain signal. By combining time-frequency analysis with a broadband acoustic excitation source, the dispersion of multiple Lamb modes over a wide frequency range can be determined from as little as a single measurement. In addition, the technique provides a direct measurement of the group velocity dispersion. The technique was first demonstrated in the analysis of a simulated waveform in an aluminum plate in which the Lamb mode dispersion was well known. Portions of the dispersion curves of the A(sub 0), A(sub 1), S(sub 0), and S(sub 2)Lamb modes were obtained from this one waveform. The technique was also applied for the analysis of experimental waveforms from a unidirectional graphite/epoxy composite plate. Measurements were made both along, and perpendicular to the fiber direction. In this case, the signals contained only the lowest order symmetric and antisymmetric modes. A least squares fit of the results from several source to detector distances was used. Theoretical dispersion curves were calculated and are shown to be in good agreement with experimental results.

New Multicentury Evidence for Dispersal Limitation during Primary Succession.

PubMed

Makoto, K; Wilson, Scott D

2016-06-01

Primary succession is limited by both ecosystem development and plant dispersal, but the extent to which dispersal constrains succession over the long-term is unknown. We compared primary succession along two co-occurring arctic chronosequences with contrasting spatial scales: sorted circles that span a few meters and may have few dispersal constraints and glacial forelands that span several kilometers and may have greater dispersal constraints. Dispersal constraints slowed primary succession by centuries: plots were dominated by cryptogams after 20 years on circles but after 270 years on forelands; plots supported deciduous plants after 100 years on circles but after >400 years on forelands. Our study provides century-scale evidence suggesting that dispersal limitations constrain the rate of primary succession in glacial forelands.

Combined effects of local habitat, anthropogenic stress, and dispersal on stream ecosystems: a mesocosm experiment.

PubMed

Turunen, Jarno; Louhi, Pauliina; Mykrä, Heikki; Aroviita, Jukka; Putkonen, Emmi; Huusko, Ari; Muotka, Timo

2018-06-06

The effects of anthropogenic stressors on community structure and ecosystem functioning can be strongly influenced by local habitat structure and dispersal from source communities. Catchment land uses increase the input of fine sediments into stream channels, clogging the interstitial spaces of benthic habitats. Aquatic macrophytes enhance habitat heterogeneity and mediate important ecosystem functions, being thus a key component of habitat structure in many streams. Therefore, the recovery of macrophytes following in-stream habitat modification may be prerequisite for successful stream restoration. Restoration success is also affected by dispersal of organisms from the source community, with potentially strongest responses in relatively isolated headwater sites that receive limited amount of dispersing individuals. We used a factorial design in a set of stream mesocosms to study the independent and combined effects of an anthropogenic stressor (sand sedimentation), local habitat (macrophytes, i.e. moss transplants) and enhanced dispersal (two levels: high vs. low) on organic matter retention, algal accrual rate, leaf decomposition and macroinvertebrate community structure. Overall, all responses were simple additive effects with no interactions between treatments. Sand reduced algal accumulation, total invertebrate density and density of a few individual taxa. Mosses reduced algal accrual rate and algae-grazing invertebrates, but enhanced organic matter retention and detritus- and filter-feeders. Mosses also reduced macroinvertebrate diversity by increasing the dominance by a few taxa. Mosses also reduced leaf-mass loss, possibly because the organic matter retained by mosses provided an additional food source for leaf-shredding invertebrates and thus reduced shredder aggregation into leaf packs. The effect of mosses on macroinvertebrate communities and ecosystem functioning was distinct irrespective of the level of dispersal, suggesting strong environmental control of community structure. The strong environmental control of macroinvertebrate community composition even under enhanced dispersal suggests that re-establishing key habitat features, such as natural stream vegetation, could aid ecosystem recovery in boreal streams. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Turbulent Combustion in SDF Explosions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kuhl, A L; Bell, J B; Beckner, V E

2009-11-12

A heterogeneous continuum model is proposed to describe the dispersion and combustion of an aluminum particle cloud in an explosion. It combines the gas-dynamic conservation laws for the gas phase with a continuum model for the dispersed phase, as formulated by Nigmatulin. Inter-phase mass, momentum and energy exchange are prescribed by phenomenological models. It incorporates a combustion model based on the mass conservation laws for fuel, air and products; source/sink terms are treated in the fast-chemistry limit appropriate for such gasdynamic fields, along with a model for mass transfer from the particle phase to the gas. The model takes intomore » account both the afterburning of the detonation products of the C-4 booster with air, and the combustion of the Al particles with air. The model equations were integrated by high-order Godunov schemes for both the gas and particle phases. Numerical simulations of the explosion fields from 1.5-g Shock-Dispersed-Fuel (SDF) charge in a 6.6 liter calorimeter were used to validate the combustion model. Then the model was applied to 10-kg Al-SDF explosions in a an unconfined height-of-burst explosion. Computed pressure histories are compared with measured waveforms. Differences are caused by physical-chemical kinetic effects of particle combustion which induce ignition delays in the initial reactive blast wave and quenching of reactions at late times. Current simulations give initial insights into such modeling issues.« less

An experimental study of the impact of trees and urban form on the turbulent dispersion of heavy particles from near ground point sources

NASA Astrophysics Data System (ADS)

Stoll, R., II; Christen, A.; Mahaffee, W.; Salesky, S.; Therias, A.; Caitlin, S.

2016-12-01

Pollution in the form of small particles has a strong impact on a wide variety of urban processes that play an important role in the function of urban ecosystems and ultimately human health and well-being. As a result, a substantial body of research exists on the sources, sinks, and transport characteristics of urban particulate matter. Most of the existing experimental work examining point sources employed gases (e.g., SF6) as the working medium. Furthermore, the focus of most studies has been on the dispersion of pollutants far from the source location. Here, our focus is on the turbulent dispersion of heavy particles in the near source region of a suburban neighborhood. To this end, we conducted a series of heavy particle releases in the Sunset neighborhood of Vancouver, Canada during June, 2017. The particles where dispersed from a near ground point source at two different locations. The Sunset neighborhood is composed mostly of single dwelling detached houses and has been used in numerous previous urban studies. One of the release points was just upwind of a 4-way intersection and the other in the middle of a contiguous block of houses. Each location had a significant density of trees. A minimum of four different successful release events were conducted at each site. During each release, fluorescing micro particles (mean diameter approx. 30 micron) were released from ultrasonic atomizer nozzles for a duration of approximately 20 minutes. The particles where sampled at 50 locations (1.5 m height) in the area downwind of the release over distances from 1-15 times the mean canopy height ( 6 m) using rotating impaction traps. In addition to the 50 sampler locations, instantaneous wind velocities were measured with eight sonic anemometers distributed horizontally and vertically throughout the release area. The resulting particle plume distributions indicate a strong impact of local urban form in the near source region and a high degree of sensitivity to the local wind direction measured from the sonic anemometers. In addition to presenting the experimental data, initial comparisons to a Lagrangian particle dispersion model driven by a mass consistent diagnostic wind field will be presented.

An experimental study of the impact of trees and urban form on the turbulent dispersion of heavy particles from near ground point sources

NASA Astrophysics Data System (ADS)

Stoll, R., II; Christen, A.; Mahaffee, W.; Salesky, S.; Therias, A.; Caitlin, S.

2017-12-01

Pollution in the form of small particles has a strong impact on a wide variety of urban processes that play an important role in the function of urban ecosystems and ultimately human health and well-being. As a result, a substantial body of research exists on the sources, sinks, and transport characteristics of urban particulate matter. Most of the existing experimental work examining point sources employed gases (e.g., SF6) as the working medium. Furthermore, the focus of most studies has been on the dispersion of pollutants far from the source location. Here, our focus is on the turbulent dispersion of heavy particles in the near source region of a suburban neighborhood. To this end, we conducted a series of heavy particle releases in the Sunset neighborhood of Vancouver, Canada during June, 2017. The particles where dispersed from a near ground point source at two different locations. The Sunset neighborhood is composed mostly of single dwelling detached houses and has been used in numerous previous urban studies. One of the release points was just upwind of a 4-way intersection and the other in the middle of a contiguous block of houses. Each location had a significant density of trees. A minimum of four different successful release events were conducted at each site. During each release, fluorescing micro particles (mean diameter approx. 30 micron) were released from ultrasonic atomizer nozzles for a duration of approximately 20 minutes. The particles where sampled at 50 locations (1.5 m height) in the area downwind of the release over distances from 1-15 times the mean canopy height ( 6 m) using rotating impaction traps. In addition to the 50 sampler locations, instantaneous wind velocities were measured with eight sonic anemometers distributed horizontally and vertically throughout the release area. The resulting particle plume distributions indicate a strong impact of local urban form in the near source region and a high degree of sensitivity to the local wind direction measured from the sonic anemometers. In addition to presenting the experimental data, initial comparisons to a Lagrangian particle dispersion model driven by a mass consistent diagnostic wind field will be presented.

THE EFFECTS OF ROADSIDE STRUCTURES ON THE TRANSPORT AND DISPERSION OF ULTRAFINE PARTICLES FROM HIGHWAYS.

EPA Science Inventory

Understanding the transport and dispersion of pollutants from traffic sources, particularly within 300 meters of a roadway is important both for urban planning and for air quality assessments. Predicting pollutant concentration patterns in complex environments depends on accurat...

AIR QUALITY SIMULATION MODEL PERFORMANCE FOR ONE-HOUR AVERAGES

EPA Science Inventory

If a one-hour standard for sulfur dioxide were promulgated, air quality dispersion modeling in the vicinity of major point sources would be an important air quality management tool. Would currently available dispersion models be suitable for use in demonstrating attainment of suc...

OIL SPILL DISPERSANT EFFECTIVENESS PROTOCOL. I: IMPACT OF OPERATIONAL VARIABLES

EPA Science Inventory

The current U.S. Environmental Protection Agency protocol for testing the effectiveness of dispersants, the swirling flask test, has been found to give widely varying results in the hands of different testing laboratories. The sources of the ambiguities in the test were determin...

Direct design of achromatic lens for Lambertian sources in collimating illumination

NASA Astrophysics Data System (ADS)

Yin, Peng; Xu, Xiping; Jiang, Zhaoguo; Wang, Hongshu

2017-10-01

Illumination design used to redistribute the spatial energy distribution of light source is a key technique in lighting applications. However, there is still no effective illumination design method for the removing of the chromatic dispersion. What we present here is an achromatic lens design to enhance the efficiency and uniform illumination of white light-emitting diode (LED) with diffractive optical element (DOE). We employ the chromatic aberration value (deg) to measure the degree of chromatic dispersion in illumination systems. Monte Carlo ray tracing simulation results indicate that the chromatic dispersion of the modified achromatic collimator significantly decreases from 0.5 to 0.1 with LED chip size of 1.0mm×1.0mm and simulation efficiency of 90.73%, compared with the traditional collimator. Moreover, with different corrected wavelengths we compared different chromatic aberration values that followed with the changing pupil percent. The achromatic collimator provided an effective way to achieve white LED with low chromatic dispersion at high efficiency and uniform illumination.

Shear wave speed and dispersion measurements using crawling wave chirps.

PubMed

Hah, Zaegyoo; Partin, Alexander; Parker, Kevin J

2014-10-01

This article demonstrates the measurement of shear wave speed and shear speed dispersion of biomaterials using a chirp signal that launches waves over a range of frequencies. A biomaterial is vibrated by two vibration sources that generate shear waves inside the medium, which is scanned by an ultrasound imaging system. Doppler processing of the acquired signal produces an image of the square of vibration amplitude that shows repetitive constructive and destructive interference patterns called "crawling waves." With a chirp vibration signal, successive Doppler frames are generated from different source frequencies. Collected frames generate a distinctive pattern which is used to calculate the shear speed and shear speed dispersion. A special reciprocal chirp is designed such that the equi-phase lines of a motion slice image are straight lines. Detailed analysis is provided to generate a closed-form solution for calculating the shear wave speed and the dispersion. Also several phantoms and an ex vivo human liver sample are scanned and the estimation results are presented. © The Author(s) 2014.

Can marine bacteria be recruited from freshwater sources and the air?

PubMed Central

Comte, Jérôme; Lindström, Eva S; Eiler, Alexander; Langenheder, Silke

2014-01-01

There is now clear evidence that microorganisms present biogeographic patterns, yet the processes that create and maintain them are still not well understood. In particular, the contribution of dispersal and its exact impact on local community composition is still unclear. For example, dispersing cells may not thrive in recipient environments, but may still remain part of the local species pool. Here, we experimentally tested if marine bacteria can be retrieved from freshwater communities (pelagic and sediment) and the atmosphere by exposing bacteria from three lakes, that differ in their proximity to the Norwegian Sea, to marine conditions. We found that the percentage of freshwater taxa decreased with increasing salinities, whereas marine taxa increased along the same gradient. Our results further showed that this increase was stronger for lake and sediment compared with air communities. Further, significant increases in the average niche breadth of taxa were found for all sources, and in particular lake water and sediment communities, at higher salinities. Our results therefore suggests that marine taxa can readily grow from freshwater sources, but that the response was likely driven by the growth of habitat generalists that are typically found in marine systems. Finally, there was a greater proportion of marine taxa found in communities originating from the lake closest to the Norwegian Sea. In summary, this study shows that the interplay between bacterial dispersal limitation and dispersal from internal and external sources may have an important role for community recovery in response to environmental change. PMID:24906016

Linear dispersion relation for the mirror instability in context of the gyrokinetic theory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Porazik, Peter; Johnson, Jay R.

2013-10-15

The linear dispersion relation for the mirror instability is discussed in context of the gyrokinetic theory. The objective is to provide a coherent view of different kinetic approaches used to derive the dispersion relation. The method based on gyrocenter phase space transformations is adopted in order to display the origin and ordering of various terms.

Plasma Dispersion Function for the Kappa Distribution

NASA Technical Reports Server (NTRS)

Podesta, John J.

2004-01-01

The plasma dispersion function is computed for a homogeneous isotropic plasma in which the particle velocities are distributed according to a Kappa distribution. An ordinary differential equation is derived for the plasma dispersion function and it is shown that the solution can be written in terms of Gauss' hypergeometric function. Using the extensive theory of the hypergeometric function, various mathematical properties of the plasma dispersion function are derived including symmetry relations, series expansions, integral representations, and closed form expressions for integer and half-integer values of K.

Intraindividual variability across cognitive domains: investigation of dispersion levels and performance profiles in older adults.

PubMed

Hilborn, Jennifer V; Strauss, Esther; Hultsch, David F; Hunter, Michael A

2009-05-01

A growing body of research suggests that substantial variability exists among cognitive abilities within individuals. This within-person variability across cognitive domains is termed dispersion. The present study investigated the relationship between aging and dispersion of cognitive functions both quantitatively (overall levels of dispersion) and qualitatively (patterns of dispersion) in a sample of 304 nondemented, older adults aged 64 to 92 years (M = 74.02). Quantitatively, higher levels of dispersion were observed in the old-old adults (aged 75-92 years) and those identified as having experienced cognitive decline, suggesting that dispersion level may serve as a marker of cognitive integrity. Qualitatively, three distinct dispersion profiles were identified through clustering methods, and these were found to be related to demographic, health, and performance characteristics of the individuals, suggesting that patterns of dispersion may be meaningful indicators of individual differences.

High-speed photonically assisted analog-to-digital conversion using a continuous wave multiwavelength source and phase modulation.

PubMed

Bortnik, Bartosz J; Fetterman, Harold R

2008-10-01

A more simple photonically assisted analog-to-digital conversion system utilizing a cw multiwavelength source and phase modulation instead of a mode-locked laser is presented. The output of the cw multiwavelength source is launched into a dispersive device (such as a single-mode fiber). This fiber creates a pulse train, where the central wavelength of each pulse corresponds to a spectral line of the optical source. The pulses can then be either dispersed again to perform discrete wavelength time stretching or demultiplexed for continuous time analog-to-digital conversion. We experimentally demonstrate the operation of both time stretched and interleaved systems at 38 GHz. The potential of integrating this type of system on a monolithic chip is discussed.

Does Light from Steady Sources Bear Any Observable Imprint of the Dispersive Intergalactic Medium?

NASA Astrophysics Data System (ADS)

Lieu, Richard; Duan, Lingze

2018-02-01

There has recently been some interest in the prospect of detecting ionized intergalactic baryons by examining the properties of incoherent light from background cosmological sources, namely quasars. Although the paper by Lieu et al. proposed a way forward, it was refuted by the later theoretical work of Hirata & McQuinn and the observational study of Hales et al. In this paper we investigate in detail the manner in which incoherent radiation passes through a dispersive medium both from the frameworks of classical and quantum electrodynamics, leading us to conclude that the premise of Lieu et al. would only work if the pulses involved are genuinely classical ones containing many photons per pulse; unfortunately, each photon must not be treated as a pulse that is susceptible to dispersive broadening. We are nevertheless able to change the tone of the paper at this juncture by pointing out that because current technology allows one to measure the phase of individual modes of radio waves from a distant source, the most reliable way of obtaining irrefutable evidence of dispersion, namely via the detection of its unique signature of a quadratic spectral phase, may well be already accessible. We demonstrate how this technique is only applied to measure the column density of the ionized intergalactic medium.

Metapopulation viability of an endangered shorebird depends on dispersal and human-created habitats: Piping plovers (Charadrius melodus) and prairie rivers

USGS Publications Warehouse

Catlin, Daniel H.; Zeigler, Sara; Bomberger Brown, M.; Dinan, Lauren R.; Fraser, James D.; Hunt, Kelsi L.; Jorgensen, Joel G.

2016-01-01

We found that functional connectivity, as measured by the rate of dispersal among subpopulations, increased as a result of the high flow event in our study metapopulation. Plovers also increased reproductive output following this event. Although the study metapopulation had a low overall probability of extinction, metapopulation persistence depended on anthropogenically created habitats that provided a small but stable source of nesting habitat and dispersers through time. However, all subpopulations remained small, even if persistent, making them individually vulnerable to extinction through stochastic events. Given the highly dynamic nature of habitat availability in this system, maintaining several subpopulations within the metapopulation and stable sources of habitat will be critical, and this species will likely remain conservation-reliant.

Chromatic dispersion effects in ultra-low coherence interferometry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lychagov, V V; Ryabukho, V P

2015-06-30

We consider the properties of an interference signal shift from zero-path-difference position in the presence of an uncompensated dispersive layer in one of the interferometer arms. It is experimentally shown that in using an ultra-low coherence light source, the formation of the interference signal is also determined by the group velocity dispersion, which results in a nonlinear dependence of the position of the interference signal on the geometrical thickness of the dispersive layer. The discrepancy in the dispersive layer and compensator refractive indices in the third decimal place is experimentally shown to lead to an interference signal shift that ismore » an order of magnitude greater than the pulse width. (interferometry)« less

Study on gas diffusion emitted from different height of point source.

PubMed

Yassin, Mohamed F

2009-01-01

The flow and dispersion of stack-gas emitted from different elevated point source around flow obstacles in an urban environment have been investigated, using computational fluid dynamics models (CFD). The results were compared with the experimental results obtained from the diffusion wind tunnel under different conditions of thermal stability (stable, neutral or unstable). The flow and dispersion fields in the boundary layer in an urban environment were examined with different flow obstacles. Gaseous pollutant was discharged in the simulated boundary layer over the flat area. The CFD models used for the simulation were based on the steady-state Reynolds-Average Navier-Stoke equations (RANS) with kappa-epsilon turbulence models; standard kappa-epsilon and RNG kappa-epsilon models. The flow and dispersion data measured in the wind tunnel experiments were compared with the results of the CFD models in order to evaluate the prediction accuracy of the pollutant dispersion. The results of the CFD models showed good agreement with the results of the wind tunnel experiments. The results indicate that the turbulent velocity is reduced by the obstacles models. The maximum dispersion appears around the wake region of the obstacles.

Redistribution of energy available for ocean mixing by long-range propagation of internal waves.

PubMed

Alford, Matthew H

2003-05-08

Ocean mixing, which affects pollutant dispersal, marine productivity and global climate, largely results from the breaking of internal gravity waves--disturbances propagating along the ocean's internal stratification. A global map of internal-wave dissipation would be useful in improving climate models, but would require knowledge of the sources of internal gravity waves and their propagation. Towards this goal, I present here computations of horizontal internal-wave propagation from 60 historical moorings and relate them to the source terms of internal waves as computed previously. Analysis of the two most energetic frequency ranges--near-inertial frequencies and semidiurnal tidal frequencies--reveals that the fluxes in both frequency bands are of the order of 1 kW x m(-1) (that is, 15-50% of the energy input) and are directed away from their respective source regions. However, the energy flux due to near-inertial waves is stronger in winter, whereas the tidal fluxes are uniform throughout the year. Both varieties of internal waves can thus significantly affect the space-time distribution of energy available for global mixing.

Numerical Simulation of Dispersion from Urban Greenhouse Gas Sources

NASA Astrophysics Data System (ADS)

Nottrott, Anders; Tan, Sze; He, Yonggang; Winkler, Renato

2017-04-01

Cities are characterized by complex topography, inhomogeneous turbulence, and variable pollutant source distributions. These features create a scale separation between local sources and urban scale emissions estimates known as the Grey-Zone. Modern computational fluid dynamics (CFD) techniques provide a quasi-deterministic, physically based toolset to bridge the scale separation gap between source level dynamics, local measurements, and urban scale emissions inventories. CFD has the capability to represent complex building topography and capture detailed 3D turbulence fields in the urban boundary layer. This presentation discusses the application of OpenFOAM to urban CFD simulations of natural gas leaks in cities. OpenFOAM is an open source software for advanced numerical simulation of engineering and environmental fluid flows. When combined with free or low cost computer aided drawing and GIS, OpenFOAM generates a detailed, 3D representation of urban wind fields. OpenFOAM was applied to model scalar emissions from various components of the natural gas distribution system, to study the impact of urban meteorology on mobile greenhouse gas measurements. The numerical experiments demonstrate that CH4 concentration profiles are highly sensitive to the relative location of emission sources and buildings. Sources separated by distances of 5-10 meters showed significant differences in vertical dispersion of plumes, due to building wake effects. The OpenFOAM flow fields were combined with an inverse, stochastic dispersion model to quantify and visualize the sensitivity of point sensors to upwind sources in various built environments. The Boussinesq approximation was applied to investigate the effects of canopy layer temperature gradients and convection on sensor footprints.

Uni-directional optical pulses, temporal propagation, and spatial and temporal dispersion

NASA Astrophysics Data System (ADS)

Kinsler, P.

2018-02-01

I derive a temporally propagated uni-directional optical pulse equation valid in the few cycle limit. Temporal propagation is advantageous because it naturally preserves causality, unlike the competing spatially propagated models. The exact coupled bi-directional equations that this approach generates can be efficiently approximated down to a uni-directional form in cases where an optical pulse changes little over one optical cycle. They also permit a direct term-to-term comparison of the exact bi-directional theory with its corresponding approximate uni-directional theory. Notably, temporal propagation handles dispersion in a different way, and this difference serves to highlight existing approximations inherent in spatially propagated treatments of dispersion. Accordingly, I emphasise the need for future work in clarifying the limitations of the dispersion conversion required by these types of approaches; since the only alternative in the few cycle limit may be to resort to the much more computationally intensive full Maxwell equation solvers.

Quantitative dispersion microscopy

PubMed Central

Fu, Dan; Choi, Wonshik; Sung, Yongjin; Yaqoob, Zahid; Dasari, Ramachandra R.; Feld, Michael

2010-01-01

Refractive index dispersion is an intrinsic optical property and a useful source of contrast in biological imaging studies. In this report, we present the first dispersion phase imaging of living eukaryotic cells. We have developed quantitative dispersion microscopy based on the principle of quantitative phase microscopy. The dual-wavelength quantitative phase microscope makes phase measurements at 310 nm and 400 nm wavelengths to quantify dispersion (refractive index increment ratio) of live cells. The measured dispersion of living HeLa cells is found to be around 1.088, which agrees well with that measured directly for protein solutions using total internal reflection. This technique, together with the dry mass and morphology measurements provided by quantitative phase microscopy, could prove to be a useful tool for distinguishing different types of biomaterials and studying spatial inhomogeneities of biological samples. PMID:21113234

Multiple-input multiple-output visible light communication system based on disorder dispersion components

NASA Astrophysics Data System (ADS)

Yang, Tao; Zhang, Qi; Hao, Yue; Zhou, Xin-hui; Yi, Ming-dong; Wei, Wei; Huang, Wei; Li, Xing-ao

2017-10-01

A multiple-input multiple-output visible light communication (VLC) system based on disorder dispersion components is presented. Instead of monochromatic sources and large size photodetectors used in the traditional VLC systems, broadband sources with different spectra act as the transmitters and a compact imaging chip sensor accompanied by a disorder dispersion component and a calculating component serve as the receivers in the proposed system. This system has the merits of small size, more channels, simple structure, easy integration, and low cost. Simultaneously, the broadband sources are suitable to act as illumination sources for their white color. A regularized procedure is designed to solve a matrix equation for decoding the signals at the receivers. A proof-of-concept experiment using on-off keying modulation has been done to prove the feasibility of the design. The experimental results show that the signals decoded by the receivers fit well with those generated from the transmitters, but the bit error ratio is increased with the number of the signal channels. The experimental results can be further improved using a high-speed charge-coupled device, decreasing noises, and increasing the distance between the transmitters and the receivers.

Hydrological modelling of snail dispersal patterns in Msambweni, Kenya and potential resurgence of Schistosoma haematobium transmission.

PubMed

Clennon, J A; King, C H; Muchiri, E M; Kitron, U

2007-05-01

Urinary schistosomiasis is an important source of human morbidity in Msambweni, Kenya, where the intermediate host snail, Bulinus nasutus is found in ponds and water pools. In the past, aquatic habitats in the area have been studied separately; however, recent collections of B. nasutus snails and shells indicated that many of these ponds are in fact connected during and following sufficient rains. Satellite imagery and a geographical information system (GIS) were used to survey the main water courses and potential drainage routes, to locate potential source populations of snails and to determine probable snail dispersal routes. The 2 water bodies implicated as being the most important Schistosoma haematobium transmission foci in the area were found to differ in their degree of connectivity to other B. nasutus source habitats. One pond becomes connected even after normal rains, while the other pond requires prolonged rains or flooding to become connected with source habitats. Consequently, the transmission foci differ in their susceptibility to snail population control measures. Spatially explicit dispersal models that consider the spatial and temporal patterns of connectivity between aquatic habitats will contribute to improved snail surveillance and more focused control for urinary schistosomiasis at a local level.

Influence of source batch S{sub K} dispersion on dosimetry for prostate cancer treatment with permanent implants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nuñez-Cumplido, E., E-mail: ejnc-mccg@hotmail.com; Hernandez-Armas, J.; Perez-Calatayud, J.

2015-08-15

Purpose: In clinical practice, specific air kerma strength (S{sub K}) value is used in treatment planning system (TPS) permanent brachytherapy implant calculations with {sup 125}I and {sup 103}Pd sources; in fact, commercial TPS provide only one S{sub K} input value for all implanted sources and the certified shipment average is typically used. However, the value for S{sub K} is dispersed: this dispersion is not only due to the manufacturing process and variation between different source batches but also due to the classification of sources into different classes according to their S{sub K} values. The purpose of this work is tomore » examine the impact of S{sub K} dispersion on typical implant parameters that are used to evaluate the dose volume histogram (DVH) for both planning target volume (PTV) and organs at risk (OARs). Methods: The authors have developed a new algorithm to compute dose distributions with different S{sub K} values for each source. Three different prostate volumes (20, 30, and 40 cm{sup 3}) were considered and two typical commercial sources of different radionuclides were used. Using a conventional TPS, clinically accepted calculations were made for {sup 125}I sources; for the palladium, typical implants were simulated. To assess the many different possible S{sub K} values for each source belonging to a class, the authors assigned an S{sub K} value to each source in a randomized process 1000 times for each source and volume. All the dose distributions generated for each set of simulations were assessed through the DVH distributions comparing with dose distributions obtained using a uniform S{sub K} value for all the implanted sources. The authors analyzed several dose coverage (V{sub 100} and D{sub 90}) and overdosage parameters for prostate and PTV and also the limiting and overdosage parameters for OARs, urethra and rectum. Results: The parameters analyzed followed a Gaussian distribution for the entire set of computed dosimetries. PTV and prostate V{sub 100} and D{sub 90} variations ranged between 0.2% and 1.78% for both sources. Variations for the overdosage parameters V{sub 150} and V{sub 200} compared to dose coverage parameters were observed and, in general, variations were larger for parameters related to {sup 125}I sources than {sup 103}Pd sources. For OAR dosimetry, variations with respect to the reference D{sub 0.1cm{sup 3}} were observed for rectum values, ranging from 2% to 3%, compared with urethra values, which ranged from 1% to 2%. Conclusions: Dose coverage for prostate and PTV was practically unaffected by S{sub K} dispersion, as was the maximum dose deposited in the urethra due to the implant technique geometry. However, the authors observed larger variations for the PTV V{sub 150}, rectum V{sub 100}, and rectum D{sub 0.1cm{sup 3}} values. The variations in rectum parameters were caused by the specific location of sources with S{sub K} value that differed from the average in the vicinity. Finally, on comparing the two sources, variations were larger for {sup 125}I than for {sup 103}Pd. This is because for {sup 103}Pd, a greater number of sources were used to obtain a valid dose distribution than for {sup 125}I, resulting in a lower variation for each S{sub K} value for each source (because the variations become averaged out statistically speaking)« less

Dispersion of a Passive Scalar Fluctuating Plume in a Turbulent Boundary Layer. Part I: Velocity and Concentration Measurements

NASA Astrophysics Data System (ADS)

Nironi, Chiara; Salizzoni, Pietro; Marro, Massimo; Mejean, Patrick; Grosjean, Nathalie; Soulhac, Lionel

2015-09-01

The prediction of the probability density function (PDF) of a pollutant concentration within atmospheric flows is of primary importance in estimating the hazard related to accidental releases of toxic or flammable substances and their effects on human health. This need motivates studies devoted to the characterization of concentration statistics of pollutants dispersion in the lower atmosphere, and their dependence on the parameters controlling their emissions. As is known from previous experimental results, concentration fluctuations are significantly influenced by the diameter of the source and its elevation. In this study, we aim to further investigate the dependence of the dispersion process on the source configuration, including source size, elevation and emission velocity. To that end we study experimentally the influence of these parameters on the statistics of the concentration of a passive scalar, measured at several distances downwind of the source. We analyze the spatial distribution of the first four moments of the concentration PDFs, with a focus on the variance, its dissipation and production and its spectral density. The information provided by the dataset, completed by estimates of the intermittency factors, allow us to discuss the role of the main mechanisms controlling the scalar dispersion and their link to the form of the PDF. The latter is shown to be very well approximated by a Gamma distribution, irrespective of the emission conditions and the distance from the source. Concentration measurements are complemented by a detailed description of the velocity statistics, including direct estimates of the Eulerian integral length scales from two-point correlations, a measurement that has been rarely presented to date.

Dispersion in a thermal plasma including arbitrary degeneracy and quantum recoil.

PubMed

Melrose, D B; Mushtaq, A

2010-11-01

The longitudinal response function for a thermal electron gas is calculated including two quantum effects exactly, degeneracy, and the quantum recoil. The Fermi-Dirac distribution is expanded in powers of a parameter that is small in the nondegenerate limit and the response function is evaluated in terms of the conventional plasma dispersion function to arbitrary order in this parameter. The infinite sum is performed in terms of polylogarithms in the long-wavelength and quasistatic limits, giving results that apply for arbitrary degeneracy. The results are applied to the dispersion relations for Langmuir waves and to screening, reproducing known results in the nondegenerate and completely degenerate limits, and generalizing them to arbitrary degeneracy.

A modeling framework for characterizing near-road air pollutant concentration at community scales

EPA Science Inventory

In this study, we combine information from transportation network, traffic emissions, and dispersion model to develop a framework to inform exposure estimates for traffic-related air pollutants (TRAPs) with a high spatial resolution. A Research LINE source dispersion model (R-LIN...

Self-starting picosecond optical pulse source using stimulated Brillouin scattering in an optical fiber.

PubMed

Tang, W W; Shu, C

2005-02-21

We demonstrate a regeneratively mode-locked optical pulse source at about 10 GHz using an optoelectronic oscillator constructed with an electro-absorption modulator integrated distributed feedback laser diode. The 10 GHz RF component is derived from the interaction between the pump wave and the backscattered, frequency-downshifted Stokes wave resulted from stimulated Brillouin scattering in an optical fiber. The component serves as a modulation source for the 1556 nm laser diode without the need for any electrical or optical RF filter to perform the frequency extraction. Dispersion-compensated fiber, dispersion-shifted fiber, and standard single-mode fiber have been used respectively to generate optical pulses at variable repetition rates.

SPECIATE--EPA'S DATABASE OF SPECIATED EMISSION PROFILES

EPA Science Inventory

SPECIATE is EPA's repository of Total Organic Compound and Particulate Matter speciated profiles for a wide variety of sources. The profiles in this system are provided for air quality dispersion modeling and as a library for source-receptor and source apportionment type models. ...

Dispersion stability in carbon nanotube modified polymers and its effect on the fracture toughness

NASA Astrophysics Data System (ADS)

Mirjalili, Vahid; Yourdkhani, Mostafa; Hubert, Pascal

2012-08-01

In this paper, the dispersion stability of multiwall carbon nanotubes (MWNTs) mixed with an epoxy resin is studied. An instrumented optical microscope with a hot stage was used to study the evolution of the carbon nanotubes (CNTs) dispersion during the cure of the resin. A new image processing approach is then introduced to quantify dispersion and identify the source of dispersion degradation during the cure. The results showed that the reduction of the resin viscosity at temperatures greater than 100 °C caused an irreversible re-agglomeration of the CNTs in the matrix. It was shown that the fine-tuning of the ratio and type of curing agent as well as the curing temperature directly affect the dispersion stability of MWNTs in the epoxy polymer. The dispersion quality was then directly correlated to the fracture toughness of the modified resin and a maximum of 20% improvement was achieved.

Vegetation development following stream/river restoration: more natural fluvial dynamics and morphology, return of aquatic and riparian plant species?

NASA Astrophysics Data System (ADS)

Soons, M. B.

2012-04-01

After centuries of human interventions in stream/river dynamics and morphology aimed at optimizing landscapes for agricultural and industrial purposes, new insights have inspired water managers to try and combine stream and river ecosystem functions with the conservation of biodiversity. Around the world, aquatic and riparian species have declined strongly due to pollution, destruction and fragmentation of their habitat, so that biodiversity conservation initiatives primarily focus on habitat restoration. In the past decades many stream and river restoration projects have been carried out and often hydrological dynamics and morphology have been restored to a more natural state. However, the successful restoration of aquatic and riparian habitats very often failed to result in restoration of their biodiversity. This lack of success from a biodiversity conservation perspective is usually attributed to 'dispersal limitation', meaning that the habitat may be restored, but species fail to reach the site and re-colonize it. Especially re-colonization by aquatic and riparian plant species is important, as such species function as ecosystem engineers: their presence alters fluvial dynamics and morphology, generates additional habitat heterogeneity and provides habitat and food for animal species. Following minor disturbances, re-colonization is often possible through locally remaining populations, by seeds in the seed bank or by surviving plant fragments. However, following major disturbances, colonization and establishment from other source populations are necessary. This usually occurs through dispersal of seeds (and in more aquatic species also by dispersal of vegetative fragments) into the restored wetland area. As dispersal occurs predominantly over short distances and source populations of aquatic and riparian species may be lacking in the surroundings, dispersal may be a limiting factor in the development of aquatic and riparian vegetation at a restored site. But, even if seeds have successfully dispersed into an area, local germination and establishment may also be limiting for the development of local biodiversity and/or for restoration success. However, we know surprisingly little about the crucial process of colonization. This presentation focusses on colonization by aquatic and riparian plant species. I combine the results of several studies investigating dispersal, germination and establishment. A study on restored riparian zones along mountain streams shows that several years after restoration, the species composition at the restored sites shows signs of dispersal limitation: species with nearby source populations re-colonized successfully, but species without source populations in the immediate surroundings often remained absent. A detailed study on the re-colonization of a restored riparian zone along a lowland stream reveals that many species enter the site as seeds, but relatively few of these seeds are able to germinate and establish successfully, indicating that both a strong dispersal filter and a strong environmental filter control local vegetation development and hence stream dynamics and morphological developments. While the intensity of the disturbance of local conditions has a great impact on the role of the environmental filter, dispersal clearly remains a limiting factor in many situations.

Characterization of edge effects in precision low-coherence interferometry using broadband light sources

NASA Astrophysics Data System (ADS)

Taudt, Ch.; Baselt, T.; Nelsen, B.; Assmann, H.; Greiner, A.; Koch, E.; Hartmann, P.

2017-06-01

Within this work an alternative approach to precision surface profilometry based on a low-coherence interferometer is presented. Special emphasis is placed on the characterization of edge effects, which influence the measurement result on sharp edges and steep slopes. In contrast to other works, this examination focuses on the comparison of very broadband light sources such as a supercontinuum white-light source (SC; 380 - 1100 nm) and a laser-driven plasma light source (LDP; 200 - 1100 nm) and their influence on the formation of these effects. The interferometer is equipped with one of these broadband light sources and a defined dispersion over a given spectral range. The spectral width of the light sources in combination with the dispersive element defines the possible measurement range and resolution. Instead of detecting the signals only in a one-dimensional manner, an imaging spectrometer on the basis of a high resolution CMOS-camera is set-up. Through the introduction of a defined dispersion, a controlled phase variation in the spectral domain is created. This phase variation is dependent on the optical path difference between both arms and can therefore be used as a measure for the height of a structure which is present in one arm. The results of measurements on a 100 nm height standard with both selected light sources have been compared. Under consideration of the coherence length of both light sources of 1.58 μm for the SC source and 1.81 m for the LDP source differences could be recorded. Especially at sharp edges, the LDP light source could record height changes with slopes twice as steep as the SC source. Furthermore, it became obvious, that measurements with the SC source tend to show edge effects like batwings due to diffraction. Additional effects on the measured roughness and the flatness of the profile were investigated and discussed.

Microlensing of an extended source by a power-law mass distribution

NASA Astrophysics Data System (ADS)

Congdon, Arthur B.; Keeton, Charles R.; Osmer, S. J.

2007-03-01

Microlensing promises to be a powerful tool for studying distant galaxies and quasars. As the data and models improve, there are systematic effects that need to be explored. Quasar continuum and broad-line regions may respond differently to microlensing due to their different sizes; to understand this effect, we study microlensing of finite sources by a mass function of stars. We find that microlensing is insensitive to the slope of the mass function but does depend on the mass range. For negative-parity images, diluting the stellar population with dark matter increases the magnification dispersion for small sources and decreases it for large sources. This implies that the quasar continuum and broad-line regions may experience very different microlensing in negative-parity lensed images. We confirm earlier conclusions that the surface brightness profile and geometry of the source have little effect on microlensing. Finally, we consider non-circular sources. We show that elliptical sources that are aligned with the direction of shear have larger magnification dispersions than sources with perpendicular alignment, an effect that becomes more prominent as the ellipticity increases. Elongated sources can lead to more rapid variability than circular sources, which raises the prospect of using microlensing to probe source shape.

Illumination Profile & Dispersion Variation Effects on Radial Velocity Measurements

NASA Astrophysics Data System (ADS)

Grieves, Nolan; Ge, Jian; Thomas, Neil B.; Ma, Bo; Li, Rui; SDSS-III

2015-01-01

The Multi-object APO Radial-Velocity Exoplanet Large-Area Survey (MARVELS) measures radial velocities using a fiber-fed dispersed fixed-delay interferometer (DFDI) with a moderate dispersion spectrograph. This setup allows a unique insight into the 2D illumination profile from the fiber on to the dispersion grating. Illumination profile investigations show large changes in the profile over time and fiber location. These profile changes are correlated with dispersion changes and long-term radial velocity offsets, a major problem within the MARVELS radial velocity data. Characterizing illumination profiles creates a method to both detect and correct radial velocity offsets, allowing for better planet detection. Here we report our early results from this study including improvement of radial velocity data points from detected giant planet candidates. We also report an illumination profile experiment conducted at the Kitt Peak National Observatory using the EXPERT instrument, which has a DFDI mode similar to MARVELS. Using profile controlling octagonal-shaped fibers, long term offsets over a 3 month time period were reduced from ~50 m/s to within the photon limit of ~4 m/s.

Localized overlap algorithm for unexpanded dispersion energies

NASA Astrophysics Data System (ADS)

Rob, Fazle; Misquitta, Alston J.; Podeszwa, Rafał; Szalewicz, Krzysztof

2014-03-01

First-principles-based, linearly scaling algorithm has been developed for calculations of dispersion energies from frequency-dependent density susceptibility (FDDS) functions with account of charge-overlap effects. The transition densities in FDDSs are fitted by a set of auxiliary atom-centered functions. The terms in the dispersion energy expression involving products of such functions are computed using either the unexpanded (exact) formula or from inexpensive asymptotic expansions, depending on the location of these functions relative to the dimer configuration. This approach leads to significant savings of computational resources. In particular, for a dimer consisting of two elongated monomers with 81 atoms each in a head-to-head configuration, the most favorable case for our algorithm, a 43-fold speedup has been achieved while the approximate dispersion energy differs by less than 1% from that computed using the standard unexpanded approach. In contrast, the dispersion energy computed from the distributed asymptotic expansion differs by dozens of percent in the van der Waals minimum region. A further increase of the size of each monomer would result in only small increased costs since all the additional terms would be computed from the asymptotic expansion.

Spore sensitivity to sunlight and freezing can restrict dispersal in wood-decay fungi

PubMed Central

Norros, Veera; Karhu, Elina; Nordén, Jenni; Vähätalo, Anssi V; Ovaskainen, Otso

2015-01-01

Assessment of the costs and benefits of dispersal is central to understanding species' life-history strategies as well as explaining and predicting spatial population dynamics in the changing world. While mortality during active movement has received much attention, few have studied the costs of passive movement such as the airborne transport of fungal spores. Here, we examine the potential of extreme environmental conditions to cause dispersal mortality in wood-decay fungi. These fungi play a key role as decomposers and habitat creators in forest ecosystems and the populations of many species have declined due to habitat loss and fragmentation. We measured the effect of simulated solar radiation (including ultraviolet A and B) and freezing at −25°C on the spore germinability of 17 species. Both treatments but especially sunlight markedly reduced spore germinability in most species, and species with thin-walled spores were particularly light sensitive. Extrapolating the species' laboratory responses to natural irradiance conditions, we predict that sunlight is a relevant source of dispersal mortality at least at larger spatial scales. In addition, we found a positive effect of spore size on spore germinability, suggesting a trade-off between dispersal distance and establishment. We conclude that freezing and particularly sunlight can be important sources of dispersal mortality in wood-decay fungi which can make it difficult for some species to colonize isolated habitat patches and habitat edges. PMID:26380666

AERMOD: A DISPERSION MODEL FOR INDUSTRIAL SOURCE APPLICATIONS PART II: MODEL PERFORMANCE AGAINST 17 FIELD STUDY DATABASES

EPA Science Inventory

The formulations of the AMS/EPA Regulatory Model Improvement Committee's applied air dispersion model (AERMOD) are described. This is the second in a series of three articles. Part I describes the model's methods for characterizing the atmospheric boundary layer and complex ter...

An intercomparison of models used to simulate the short-range atmospheric dispersion of agricultural ammonia emissions

EPA Science Inventory

Ammonia emitted into the atmosphere from agricultural sources can have an impact on nearby sensitive ecosystems either through elevated ambient concentrations or dry/wet deposition to vegetation and soil surfaces. Short-range atmospheric dispersion models are often used to assess...

Moss protonemata are dispersed by water, wind, and snails.

PubMed

Pasiche-Lisboa, Carlos J; Jesús, Inés Sastre-De

2018-04-01

Mosses produce asexual propagules, which are dispersed, thus allowing population establishment and maintenance. However, it is unknown if or how protonemata-one of their asexually produced propagules-are dispersed. Moss protonemata were exposed to three dispersal vectors (water, wind, and snails) to describe the dispersal capability and survival after dispersal. The protonemata of mosses Callicostella belangeriana and Taxiphyllum taxirameum were splashed with water drops from a 1 or 2 m height, exposed to two wind velocities (V 1 = 2.74 mps and V 2 = 3.76 mps), and fed to terrestrial snails. Dispersal of protonemata was described for wind and water by studying the dispersal distance and the relationships between protonemata sizes and dispersal distances. Survival after dispersal was recorded for the three vectors. Water and wind dispersed protonemata up to 80 and 265.5 cm, respectively. The protonemata dispersed the farthest distance when splashed by 2 m drops and hit by V 2 wind velocities. No, or little, relationship between protonemata size and dispersal distance was found for the water and wind vectors. Protonemata survived and became established after dispersal: survival was high when dispersed by water and snails, but was low for wind. For the first time, it was shown that protonemata are dispersed mostly close to the source, which is suggested to aid in moss population maintenance. © 2018 Botanical Society of America.

Anticorrosive performance of waterborne epoxy coatings containing water-dispersible hexagonal boron nitride (h-BN) nanosheets

NASA Astrophysics Data System (ADS)

Cui, Mingjun; Ren, Siming; Chen, Jia; Liu, Shuan; Zhang, Guangan; Zhao, Haichao; Wang, Liping; Xue, Qunji

2017-03-01

Homogenous dispersion of hexagonal boron nitride (h-BN) nanosheets in solvents or in the polymer matrix is crucial to initiate their many applications. Here, homogeneous dispersion of hexagonal boron nitride (h-BN) in epoxy matrix was achieved with a water-soluble carboxylated aniline trimer derivative (CAT-) as a dispersant, which was attributed to the strong π-π interaction between h-BN and CAT-, as proved by Raman and UV-vis spectra. Transmission electron microscopy (TEM) analysis confirmed a random dispersion of h-BN nanosheets in the waterborne epoxy coatings. The deterioration process of water-borne epoxy coating with and without h-BN nanosheets during the long-term immersion in 3.5 wt% NaCl solution was investigated by electrochemical measurements and water absorption test. Results implied that the introduction of well dispersed h-BN nanosheets into waterborne epoxy system remarkably improved the corrosion protection performance to substrate. Moreover, 1 wt% BN/EP composite coated substrate exhibited higher impedance modulus (1.3 × 106 Ω cm2) and lower water absorption (4%) than those of pure waterborne epoxy coating coated electrode after long-term immersion in 3.5 wt% NaCl solution, demonstrating its superior anticorrosive performance. This enhanced anticorrosive performance was mainly ascribed to the improved water barrier property of epoxy coating via incorporating homogeneously dispersed h-BN nanosheets.

Tracing the HIV-1 subtype B mobility in Europe: a phylogeographic approach

PubMed Central

Paraskevis, Dimitrios; Pybus, Oliver; Magiorkinis, Gkikas; Hatzakis, Angelos; Wensing, Annemarie MJ; van de Vijver, David A; Albert, Jan; Angarano, Guiseppe; Åsjö, Birgitta; Balotta, Claudia; Boeri, Enzo; Camacho, Ricardo; Chaix, Marie-Laure; Coughlan, Suzie; Costagliola, Dominique; De Luca, Andrea; de Mendoza, Carmen; Derdelinckx, Inge; Grossman, Zehava; Hamouda, Osama; Hoepelman, IM; Horban, Andrzej; Korn, Klaus; Kücherer, Claudia; Leitner, Thomas; Loveday, Clive; MacRae, Eilidh; Maljkovic-Berry, I; Meyer, Laurence; Nielsen, Claus; Op de Coul, Eline LM; Ormaasen, Vidar; Perrin, Luc; Puchhammer-Stöckl, Elisabeth; Ruiz, Lidia; Salminen, Mika O; Schmit, Jean-Claude; Schuurman, Rob; Soriano, Vincent; Stanczak, J; Stanojevic, Maja; Struck, Daniel; Van Laethem, Kristel; Violin, M; Yerly, Sabine; Zazzi, Maurizio; Boucher, Charles A; Vandamme, Anne-Mieke

2009-01-01

Background The prevalence and the origin of HIV-1 subtype B, the most prevalent circulating clade among the long-term residents in Europe, have been studied extensively. However the spatial diffusion of the epidemic from the perspective of the virus has not previously been traced. Results In the current study we inferred the migration history of HIV-1 subtype B by way of a phylogeography of viral sequences sampled from 16 European countries and Israel. Migration events were inferred from viral phylogenies by character reconstruction using parsimony. With regard to the spatial dispersal of the HIV subtype B sequences across viral phylogenies, in most of the countries in Europe the epidemic was introduced by multiple sources and subsequently spread within local networks. Poland provides an exception where most of the infections were the result of a single point introduction. According to the significant migratory pathways, we show that there are considerable differences across Europe. Specifically, Greece, Portugal, Serbia and Spain, provide sources shedding HIV-1; Austria, Belgium and Luxembourg, on the other hand, are migratory targets, while for Denmark, Germany, Italy, Israel, Norway, the Netherlands, Sweden, Switzerland and the UK we inferred significant bidirectional migration. For Poland no significant migratory pathways were inferred. Conclusion Subtype B phylogeographies provide a new insight about the geographical distribution of viral lineages, as well as the significant pathways of virus dispersal across Europe, suggesting that intervention strategies should also address tourists, travellers and migrants. PMID:19457244

Tracing the HIV-1 subtype B mobility in Europe: a phylogeographic approach

DOE Office of Scientific and Technical Information (OSTI.GOV)

Leitner, Thomas; Paraskevis, D; Pybus, O

2008-01-01

The prevalence and the origin of HIV-1 subtype B, the most prevalent circulating clade among the long-term residents in Europe, have been studied extensively. However the spatial diffusion of the epidemic from the perspective of the virus has not previously been traced. In the current study we inferred the migration history of HIV-1 subtype B by way of a phylogeography of viral sequences sampled from 16 European countries and Israel. Migration events were inferred from viral phylogenies by character reconstruction using parsimony. With regard to the spatial dispersal of the HIV subtype B sequences across viral phylogenies, in most ofmore » the countries in Europe the epidemic was introduced by multiple sources and subsequently spread within local networks. Poland provides an exception where most of the infections were the result of a single point introduction. According to the significant migratory pathways, we show that there are considerable differences across Europe. Specifically, Greece, Portugal, Serbia and Spain, provide sources shedding HIV-1; Austria, Belgium and Luxembourg, on the other hand, are migratory targets, while for Denmark, Germany, Italy, Israel, Norway, the Netherlands, Sweden, Switzerland and the UK we inferred significant bidirectional migration. For Poland no significant migratory pathways were inferred. Subtype B phylogeographies provide a new insight about the geographical distribution of viral lineages, as well as the significant pathways of virus dispersal across Europe, suggesting that intervention strategies should also address tourists, travellers and migrants.« less

Dispersion analysis of passive surface-wave noise generated during hydraulic-fracturing operations

USGS Publications Warehouse

Forghani-Arani, Farnoush; Willis, Mark; Snieder, Roel; Haines, Seth S.; Behura, Jyoti; Batzle, Mike; Davidson, Michael

2014-01-01

Surface-wave dispersion analysis is useful for estimating near-surface shear-wave velocity models, designing receiver arrays, and suppressing surface waves. Here, we analyze whether passive seismic noise generated during hydraulic-fracturing operations can be used to extract surface-wave dispersion characteristics. Applying seismic interferometry to noise measurements, we extract surface waves by cross-correlating several minutes of passive records; this approach is distinct from previous studies that used hours or days of passive records for cross-correlation. For comparison, we also perform dispersion analysis for an active-source array that has some receivers in common with the passive array. The active and passive data show good agreement in the dispersive character of the fundamental-mode surface-waves. For the higher mode surface waves, however, active and passive data resolve the dispersive properties at different frequency ranges. To demonstrate an application of dispersion analysis, we invert the observed surface-wave dispersion characteristics to determine the near-surface, one-dimensional shear-wave velocity.

A review of the basic concepts of dense gas dispersion with special regard to modelling of heat transfer

NASA Astrophysics Data System (ADS)

Tasker, M. N.

1984-01-01

Dense gas dispersion is the study of the spreading and dilution of a gas that has a density greater than that of ambient air. Models to predict the dispersion of such dense gases as chlorine, sulfur dioxide, liquefied natural gas, and liquid propane are necessary to prevent a catastrophe in environmental and/or human terms. A basic physical picture of dense gas dispersion is provided. Mathematical and wind tunnel models of dense gas flow are presented and discussed, including the constraints and disadvantages of modelling techniques. Special emphasis is given to heat transfer during dense gas dispersion.

Landscape characteristics of Rhizophora mangle forests and propagule deposition in coastal environments of Florida (USA)

USGS Publications Warehouse

Sengupta, R.; Middleton, B.; Yan, C.; Zuro, M.; Hartman, H.

2005-01-01

Field dispersal studies are seldom conducted at regional scales even though reliable information on mid-range dispersal distance is essential for models of colonization. The purpose of this study was to examine the potential distance of dispersal of Rhizophora mangle propagules by comparing deposition density with landscape characteristics of mangrove forests. Propagule density was estimated at various distances to mangrove sources (R. mangle) on beaches in southwestern Florida in both high-and low-energy environments, either facing open gulf waters vs. sheltered, respectively. Remote sensing and Geographic Information Systems were used to identify source forests and to determine their landscape characteristics (forest size and distance to deposition area) for the regression analyses. Our results indicated that increasing density of propagules stranded on beaches was related negatively to the distance of the deposition sites from the nearest stands of R. mangle and that deposition was greatly diminished 2 km or more from the source. Measures of fragmentation such as the area of the R. mangle forests were related to propagule deposition but only in low-energy environments. Our results suggest that geographic models involving the colonization of coastal mangrove systems should include dispersal dynamics at mid-range scales, i.e., for our purposes here, beyond the local scale of the forest and up to 5 km distant. Studies of mangrove propagule deposition at various spatial scales are key to understanding regeneration limitations in natural gaps and restoration areas. Therefore, our study of mid-range propagule dispersal has broad application to plant ecology, restoration, and modeling. ?? Springer 2005.

Attenuation and velocity dispersion in the exploration seismic frequency band

NASA Astrophysics Data System (ADS)

Sun, Langqiu

In an anelastic medium, seismic waves are distorted by attenuation and velocity dispersion, which depend on petrophysical properties of reservoir rocks. The effective attenuation and velocity dispersion is a combination of intrinsic attenuation and apparent attenuation due to scattering, transmission response, and data acquisition system. Velocity dispersion is usually neglected in seismic data processing partly because of insufficient observations in the exploration seismic frequency band. This thesis investigates the methods of measuring velocity dispersion in the exploration seismic frequency band and interprets the velocity dispersion data in terms of petrophysical properties. Broadband, uncorrelated vibrator data are suitable for measuring velocity dispersion in the exploration seismic frequency band, and a broad bandwidth optimizes the observability of velocity dispersion. Four methods of measuring velocity dispersion in uncorrelated vibrator VSP data are investigated, which are the sliding window crosscorrelation (SWCC) method, the instantaneous phase method, the spectral decomposition method, and the cross spectrum method. Among them, the SWCC method is a new method and has satisfactory robustness, accuracy, and efficiency. Using the SWCC method, velocity dispersion is measured in the uncorrelated vibrator VSP data from three areas with different geological settings, i.e., Mallik gas hydrate zone, McArthur River uranium mines, and Outokumpu crystalline rocks. The observed velocity dispersion is fitted to a straight line with respect to log frequency for a constant (frequency-independent) Q value. This provides an alternative method for calculating Q. A constant Q value does not directly link to petrophysical properties. A modeling study is implemented for the Mallik and McArthur River data to interpret the velocity dispersion observations in terms of petrophysical properties. The detailed multi-parameter petrophysical reservoir models are built according to the well logs; the models' parameters are adjusted by fitting the synthetic data to the observed data. In this way, seismic attenuation and velocity dispersion provide new insight into petrophysics properties at the Mallik and McArthur River sites. Potentially, observations of attenuation and velocity dispersion in the exploration seismic frequency band can improve the deconvolution process for vibrator data, Q-compensation, near-surface analysis, and first break picking for seismic data.

Asymptotic profile of global solutions to the generalized double dispersion equation via the nonlinear term

NASA Astrophysics Data System (ADS)

Wang, Yu-Zhu; Wei, Changhua

2018-04-01

In this paper, we investigate the initial value problem for the generalized double dispersion equation in R^n. Weighted decay estimate and asymptotic profile of global solutions are established for n≥3 . The global existence result was already proved by Kawashima and the first author in Kawashima and Wang (Anal Appl 13:233-254, 2015). Here, we show that the nonlinear term plays an important role in this asymptotic profile.

THE EFFECT OF UNRESOLVED BINARIES ON GLOBULAR CLUSTER PROPER-MOTION DISPERSION PROFILES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bianchini, P.; Norris, M. A.; Ven, G. van de

2016-03-20

High-precision kinematic studies of globular clusters (GCs) require an accurate knowledge of all possible sources of contamination. Among other sources, binary stars can introduce systematic biases in the kinematics. Using a set of Monte Carlo cluster simulations with different concentrations and binary fractions, we investigate the effect of unresolved binaries on proper-motion dispersion profiles, treating the simulations like Hubble Space Telescope proper-motion samples. Since GCs evolve toward a state of partial energy equipartition, more-massive stars lose energy and decrease their velocity dispersion. As a consequence, on average, binaries have a lower velocity dispersion, since they are more-massive kinematic tracers. Wemore » show that, in the case of clusters with high binary fractions (initial binary fractions of 50%) and high concentrations (i.e., closer to energy equipartition), unresolved binaries introduce a color-dependent bias in the velocity dispersion of main-sequence stars of the order of 0.1–0.3 km s{sup −1} (corresponding to 1%−6% of the velocity dispersion), with the reddest stars having a lower velocity dispersion, due to the higher fraction of contaminating binaries. This bias depends on the ability to distinguish binaries from single stars, on the details of the color–magnitude diagram and the photometric errors. We apply our analysis to the HSTPROMO data set of NGC 7078 (M15) and show that no effect ascribable to binaries is observed, consistent with the low binary fraction of the cluster. Our work indicates that binaries do not significantly bias proper-motion velocity-dispersion profiles, but should be taken into account in the error budget of kinematic analyses.« less

CityFlux perfluorocarbon tracer experiments

NASA Astrophysics Data System (ADS)

Petersson, F. K.; Martin, D.; White, I. R.; Henshaw, S. J.; Nickless, G.; Longley, I.; Percival, C. J.; Gallagher, M.; Shallcross, D. E.

2010-01-01

In June 2006, two perfluorocarbon tracer experiments were conducted in central Manchester UK as part of the CityFlux campaign. The main aim was to investigate vertical dispersion in an urban area during convective conditions, but dispersion mechanisms within the street network were also studied. Paired receptors were used in most cases where one receptor was located at ground level and one at roof level. One receptor was located on the roof of Portland Tower which is an 80 m high building in central Manchester. Source receptor distances in the two experiments varied between 120 and 600 m. The results reveal that maximum concentration was sometimes found at roof level rather than at ground level implying the effectiveness of convective forces on dispersion. The degree of vertical dispersion was found to be dependent on source receptor distance as well as on building height in proximity to the release site. Evidence of flow channelling in a street canyon was also found. Both a Gaussian profile and a street network model were applied and the results show that the urban topography may lead to highly effective flow channelling which therefore may be a very important dispersion mechanism should the right meteorological conditions prevail. The experimental results from this campaign have also been compared with a simple urban dispersion model that was developed during the DAPPLE framework and show good agreement with this. The results presented here are some of the first published regarding vertical dispersion. More tracer experiments are needed in order to further characterise vertical concentration profiles and their dependence on, for instance, atmospheric stability. The impact of urban topography on pollutant dispersion is important to focus on in future tracer experiments in order to improve performance of models as well as for our understanding of the relationship between air quality and public health.

CityFlux perfluorocarbon tracer experiments

NASA Astrophysics Data System (ADS)

Petersson, F. K.; Martin, D.; White, I. R.; Henshaw, S. J.; Nickless, G.; Longley, I.; Percival, C. J.; Gallagher, M.; Shallcross, D. E.

2010-07-01

In June 2006, two perfluorocarbon tracer experiments were conducted in central Manchester UK as part of the CityFlux campaign. The main aim was to investigate vertical dispersion in an urban area during convective conditions, but dispersion mechanisms within the street network were also studied. Paired receptors were used in most cases where one receptor was located at ground level and one at roof level. One receptor was located on the roof of Portland Tower which is an 80 m high building in central Manchester. Source receptor distances in the two experiments varied between 120 and 600 m. The results reveal that maximum concentration was sometimes found at roof level rather than at ground level implying the effectiveness of convective forces on dispersion. The degree of vertical dispersion was found to be dependent on source receptor distance as well as on building height in proximity to the release site. Evidence of flow channelling in a street canyon was also found. Both a Gaussian profile and a street network model were applied and the results show that the urban topography may lead to highly effective flow channelling which therefore may be a very important dispersion mechanism should the right meteorological conditions prevail. The experimental results from this campaign have also been compared with a simple urban dispersion model that was developed during the DAPPLE framework and show good agreement with this. The results presented here are some of the first published regarding vertical dispersion. More tracer experiments are needed in order to further characterise vertical concentration profiles and their dependence on, for instance, atmospheric stability. The impact of urban topography on pollutant dispersion is important to focus on in future tracer experiments in order to improve performance of models as well as for our understanding of the relationship between air quality and public health.

Comparison of volume and surface area nonpolar solvation free energy terms for implicit solvent simulations.

PubMed

Lee, Michael S; Olson, Mark A

2013-07-28

Implicit solvent models for molecular dynamics simulations are often composed of polar and nonpolar terms. Typically, the nonpolar solvation free energy is approximated by the solvent-accessible-surface area times a constant factor. More sophisticated approaches incorporate an estimate of the attractive dispersion forces of the solvent and∕or a solvent-accessible volume cavitation term. In this work, we confirm that a single volume-based nonpolar term most closely fits the dispersion and cavitation forces obtained from benchmark explicit solvent simulations of fixed protein conformations. Next, we incorporated the volume term into molecular dynamics simulations and find the term is not universally suitable for folding up small proteins. We surmise that while mean-field cavitation terms such as volume and SASA often tilt the energy landscape towards native-like folds, they also may sporadically introduce bottlenecks into the folding pathway that hinder the progression towards the native state.

Comparison of volume and surface area nonpolar solvation free energy terms for implicit solvent simulations

NASA Astrophysics Data System (ADS)

Lee, Michael S.; Olson, Mark A.

2013-07-01

Implicit solvent models for molecular dynamics simulations are often composed of polar and nonpolar terms. Typically, the nonpolar solvation free energy is approximated by the solvent-accessible-surface area times a constant factor. More sophisticated approaches incorporate an estimate of the attractive dispersion forces of the solvent and/or a solvent-accessible volume cavitation term. In this work, we confirm that a single volume-based nonpolar term most closely fits the dispersion and cavitation forces obtained from benchmark explicit solvent simulations of fixed protein conformations. Next, we incorporated the volume term into molecular dynamics simulations and find the term is not universally suitable for folding up small proteins. We surmise that while mean-field cavitation terms such as volume and SASA often tilt the energy landscape towards native-like folds, they also may sporadically introduce bottlenecks into the folding pathway that hinder the progression towards the native state.

The extent of wind-mediated dispersal of small metazoans, focusing nematodes.

PubMed

Ptatscheck, Christoph; Gansfort, Birgit; Traunspurger, Walter

2018-05-01

Wind-mediated transport is an important mechanism in the dispersal of small metazoans. Yet, concrete dispersal rates have hardly been examined. Here we present the results of an one-year field experiment investigating the composition and dispersal rates of aeroplankton. To gain insights into the dynamics of dispersal at the species level, we focused on nematodes, worldwide the most common metazoan taxon. Among the six taxa collected in this study (nematodes, rotifers, collembolans, tardigrades, mites, and thrips), nematodes had the highest dispersal rates (up to >3000 individuals m -2 in 4 weeks, 27 species identified) and represented >44% of aeroplankton. Only living nematodes, and no propagules, were dispersed. All taxa had a higher dispersal potential in environments linked to the source habitat, evidenced by the much higher deposition of organisms in funnels placed on the ground than on the rooftop of a ten-story building. Nematodes under conditions of high humidity and wind speed had the highest dispersal rates, while increasing temperatures and dryness had a significantly positive impact on the wind drift of mites and thrips. The results indicated that wind dispersal over long distances is possible. The notable organismal input by wind dispersal may contribute to biodiversity and ecosystem functions.

Contaminant dispersal in bounded turbulent shear flow

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wallace, J.M.; Bernard, P.S.; Chiang, K.F.

The dispersion of smoke downstream of a line source at the wall and at y{sup +} = 30 in a turbulent boundary layer has been predicted with a non-local model of the scalar fluxes {bar u}c and {bar v}c. The predicted plume from the wall source has been compared to high Schmidt number experimental measurements using a combination of hot-wire anemometry to obtain velocity component data synchronously with concentration data obtained optically. The predicted plumes from the source at y{sup +} = 30 and at the wall also have been compared to a low Schmidt number direct numerical simulation. Nearmore » the source, the non-local flux models give considerably better predictions than models which account solely for mean gradient transport. At a sufficient distance downstream the gradient models gives reasonably good predictions.« less

Infrasonic induced ground motions

NASA Astrophysics Data System (ADS)

Lin, Ting-Li

On January 28, 2004, the CERI seismic network recorded seismic signals generated by an unknown source. Our conclusion is that the acoustic waves were initiated by an explosive source near the ground surface. The meteorological temperature and effective sound speed profiles suggested existence of an efficient near-surface waveguide that allowed the acoustic disturbance to propagate to large distances. An explosion occurring in an area of forest and farms would have limited the number of eyewitnesses. Resolution of the source might be possible by experiment or by detailed analysis of the ground motion data. A seismo-acoustic array was built to investigate thunder-induced ground motions. Two thunder events with similar N-wave waveforms but different horizontal slownesses are chosen to evaluate the credibility of using thunder as a seismic source. These impulsive acoustic waves excited P and S reverberations in the near surface that depend on both the incident wave horizontal slowness and the velocity structure in the upper 30 meters. Nineteen thunder events were chosen to further investigate the seismo-acoustic coupling. The consistent incident slowness differences between acoustic pressure and ground motions suggest that ground reverberations were first initiated somewhat away from the array. Acoustic and seismic signals were used to generate the time-domain transfer function through the deconvolution technique. Possible non-linear interaction for acoustic propagation into the soil at the surface was observed. The reverse radial initial motions suggest a low Poisson's ratio for the near-surface layer. The acoustic-to-seismic transfer functions show a consistent reverberation series of the Rayleigh wave type, which has a systematic dispersion relation to incident slownesses inferred from the seismic ground velocity. Air-coupled Rayleigh wave dispersion was used to quantitatively constrain the near-surface site structure with constraints afforded by near-surface body wave refraction and Rayleigh wave dispersion data. Theoretical standard high-frequency and air-coupled Rayleigh wave dispersion calculated by the inferred site structure match the observed dispersion curves. Our study suggests that natural or controlled air-borne pressure sources can be used to investigate the near-surface site structures for earthquake shaking hazard studies.

A Semi-Analytical Model for Dispersion Modelling Studies in the Atmospheric Boundary Layer

NASA Astrophysics Data System (ADS)

Gupta, A.; Sharan, M.

2017-12-01

The severe impact of harmful air pollutants has always been a cause of concern for a wide variety of air quality analysis. The analytical models based on the solution of the advection-diffusion equation have been the first and remain the convenient way for modeling air pollutant dispersion as it is easy to handle the dispersion parameters and related physics in it. A mathematical model describing the crosswind integrated concentration is presented. The analytical solution to the resulting advection-diffusion equation is limited to a constant and simple profiles of eddy diffusivity and wind speed. In practice, the wind speed depends on the vertical height above the ground and eddy diffusivity profiles on the downwind distance from the source as well as the vertical height. In the present model, a method of eigen-function expansion is used to solve the resulting partial differential equation with the appropriate boundary conditions. This leads to a system of first order ordinary differential equations with a coefficient matrix depending on the downwind distance. The solution of this system, in general, can be expressed in terms of Peano-baker series which is not easy to compute, particularly when the coefficient matrix becomes non-commutative (Martin et al., 1967). An approach based on Taylor's series expansion is introduced to find the numerical solution of first order system. The method is applied to various profiles of wind speed and eddy diffusivities. The solution computed from the proposed methodology is found to be efficient and accurate in comparison to those available in the literature. The performance of the model is evaluated with the diffusion datasets from Copenhagen (Gryning et al., 1987) and Hanford (Doran et al., 1985). In addition, the proposed method is used to deduce three dimensional concentrations by considering the Gaussian distribution in crosswind direction, which is also evaluated with diffusion data corresponding to a continuous point source.

Asteroid family dynamics in the inner main belt

NASA Astrophysics Data System (ADS)

Dykhuis, Melissa Joy

The inner main asteroid belt is an important source of near-Earth objects and terrestrial planet impactors; however, the dynamics and history of this region are challenging to understand, due to its high population density and the presence of multiple orbital resonances. This dissertation explores the properties of two of the most populous inner main belt family groups --- the Flora family and the Nysa-Polana complex --- investigating their memberships, ages, spin properties, collision dynamics, and range in orbital and reflectance parameters. Though diffuse, the family associated with asteroid (8) Flora dominates the inner main belt in terms of the extent of its members in orbital parameter space, resulting in its significant overlap with multiple neighboring families. This dissertation introduces a new method for membership determination (the core sample method) which enables the distinction of the Flora family from the background, permitting its further analysis. The Flora family is shown to have a signature in plots of semimajor axis vs. size consistent with that expected for a collisional family dispersed as a result of the Yarkovsky radiation effect. The family's age is determined from the Yarkovsky dispersion to be 950 My. Furthermore, a survey of the spin sense of 21 Flora-region asteroids, accomplished via a time-efficient modification of the epoch method for spin sense determination, confirms the single-collision Yarkovsky-dispersed model for the family's origin. The neighboring Nysa-Polana complex is the likely source region for many of the carbonaceous near-Earth asteroids, several of which are important targets for spacecraft reconnaissance and sample return missions. Family identification in the Nysa-Polana complex via the core sample method reveals two families associated with asteroid (135) Hertha, both with distinct age and reflectance properties. The larger of these two families demonstrates a correlation in semimajor axis and eccentricity indicating that its family-forming collision occurred near the parent body's aphelion. In addition, the Eulalia family is connected with a possible second component, suggesting an anisotropic distribution of ejecta from its collision event.

Assembly of the eastern North American herpetofauna: new evidence from lizards and frogs

PubMed Central

Robert Macey, J; Schulte, James A; Strasburg, Jared L; Brisson, Jennifer A; Larson, Allan; Ananjeva, Natalia B; Wang, Yuezhao; Parham, James F; Papenfuss, Theodore J

2006-01-01

Darwin first recognized the importance of episodic intercontinental dispersal in the establishment of worldwide biotic diversity. Faunal exchange across the Bering Land Bridge is a major example of such dispersal. Here, we demonstrate with mitochondrial DNA evidence that three independent dispersal events from Asia to North America are the source for almost all lizard taxa found in continental eastern North America. Two other dispersal events across Beringia account for observed diversity among North American ranid frogs, one of the most species-rich groups of frogs in eastern North America. The contribution of faunal elements from Asia via dispersal across Beringia is a dominant theme in the historical assembly of the eastern North American herpetofauna. PMID:17148411

Measurement and Modeling of Dispersive Pulse Propagation in Drawn Wire Waveguides

NASA Technical Reports Server (NTRS)

Madaras, Eric I.; Kohl, Thomas W.; Rogers, Wayne P.

1995-01-01

An analytical model of dispersive pulse propagation in semi-infinite cylinders due to transient axially symmetric end conditions has been experimentally investigated. Specifically, the dispersive propagation of the first axially symmetric longitudinal mode in thin wire waveguides, which have ends in butt contact with longitudinal piezoelectric ultrasonic transducers, is examined. The method allows for prediction of a propagated waveform given a measured source waveform, together with the material properties of the cylinder. Alternatively, the source waveform can be extracted from measurement of the propagated waveform. The material properties required for implementation of the pulse propagation model are determined using guided wave phase velocity measurements. Hard tempered aluminum 1100 and 304 stainless steel wires, with 127, 305, and 406 micron diam., were examined. In general, the drawn wires were found to behave as transversely isotropic media.

Measurement and modeling of dispersive pulse propagation in draw wire waveguides

NASA Technical Reports Server (NTRS)

Madaras, Eric I.; Kohl, Thomas W.; Rogers, Wayne P.

1995-01-01

An analytical model of dispersive pulse propagation in semi-infinite cylinders due to transient axially symmetric end conditions has been experimentally investigated. Specifically, the dispersive propagation of the first axially symmetric longitudinal mode in thin wire waveguides, which have ends in butt contact with longitudinal piezoelectric ultrasonic transducers, is examined. The method allows for prediction of a propagated waveform given a measured source waveform, together with the material properties of the cylinder. Alternatively, the source waveform can be extracted from measurement of the propagated waveform. The material properties required for implementation of the pulse propagation model are determined using guided wave phase velocity measurements. Hard tempered aluminum 1100 and 304 stainless steel wires, with 127, 305, and 406 micron diam., were examined. In general, the drawn wires were found to behave as transversely isotropic media.

Enhancing sensitivity of high resolution optical coherence tomography using an optional spectrally encoded extended source (Conference Presentation)

NASA Astrophysics Data System (ADS)

Yu, Xiaojun; Liu, Xinyu; Chen, Si; Wang, Xianghong; Liu, Linbo

2016-03-01

High-resolution optical coherence tomography (OCT) is of critical importance to disease diagnosis because it is capable of providing detailed microstructural information of the biological tissues. However, a compromise usually has to be made between its spatial resolutions and sensitivity due to the suboptimal spectral response of the system components, such as the linear camera, the dispersion grating, and the focusing lenses, etc. In this study, we demonstrate an OCT system that achieves both high spatial resolutions and enhanced sensitivity through utilizing a spectrally encoded source. The system achieves a lateral resolution of 3.1 μm and an axial resolution of 2.3 μm in air; when with a simple dispersive prism placed in the infinity space of the sample arm optics, the illumination beam on the sample is transformed into a line source with a visual angle of 10.3 mrad. Such an extended source technique allows a ~4 times larger maximum permissible exposure (MPE) than its point source counterpart, which thus improves the system sensitivity by ~6dB. In addition, the dispersive prism can be conveniently switched to a reflector. Such flexibility helps increase the penetration depth of the system without increasing the complexity of the current point source devices. We conducted experiments to characterize the system's imaging capability using the human fingertip in vivo and the swine eye optic never disc ex vivo. The higher penetration depth of such a system over the conventional point source OCT system is also demonstrated in these two tissues.

Pedagogy of the Dispersed: A Cost-Benefit Analysis of the African Diaspora Phenomenon through the Human and Social Capital Lens

ERIC Educational Resources Information Center

Kivunja, Charles; Shizha, Edward

2015-01-01

With its origin in Greek where "diaspora" as a noun means "a dispersion" or as a verb means to "scatter about", the term is used in this paper to refer to the dispersion or scattering of Africans from their original African homeland and now live in countries other than their own. Indeed some Africans have dispersed…

All-fiber broadband supercontinuum generation in a single-mode high nonlinear silica fiber

NASA Astrophysics Data System (ADS)

Gao, Weiqing; Liao, Meisong; Yang, Lingzhen; Yan, Xin; Suzuki, Takenobu; Ohishi, Yasutake

2012-06-01

We demonstrate an all-fiber broadband supercontinuum (SC) source with high efficiency in a single-mode high nonlinear silica fiber. The SC is pumped by the 1557 nm sub-picosecond pulse, which is generated by a homemade passively mode-locked fiber laser, amplified by an EDFA and compressed to 600 fs. The high nonlinear fiber used in experiments has the zero-dispersion wavelength of 1584 nm with low dispersion slope. The pump pulse is in the normal dispersion region and the SC generation is initiated by the SPM effect. When the long-wave band of the spectrum is extended to the anomalous dispersion region, the soliton effects and intra-pulse Raman effects extend the spectrum further. Meanwhile, the dispersive waves shorter than 1100 nm begin to emerge because the phase matching condition is satisfied and the intensity increases with increasing the pump intensity. The broad SC spectrum with the spectral range from 840 to 2390 nm is obtained at the pump peak power of 46.71 kW, and the 10 dB bandwidth from 1120 nm to 2245 nm of the SC covers one octave assuming the peak near 1550 nm is filtered. The temporal trace of the SC has the repetition rate of 16.7 MHz, and some satellite pulses are generated during the nonlinear process. The SC source system is constructed by all-fiber components, which can be fusion spliced together directly with low loss less than 0.1 dB and improves the energy transfer efficiency from the pump source to the SC greatly. The maximum SC average power of 332 mW is obtained for the total spectral range, and the slop efficiency to the pump source is about 70.3%, which will be lower when the peaks near 1550 nm are filtered, but is higher than those in PCFs. The spectral density for the 10 dB bandwidth is in the range from -17.3 to -7.3 dBm/nm.

Climate change in metacommunities: dispersal gives double-sided effects on persistence.

PubMed

Eklöf, Anna; Kaneryd, Linda; Münger, Peter

2012-11-05

Climate change is increasingly affecting the structure and dynamics of ecological communities both at local and at regional scales, and this can be expected to have important consequences for their robustness and long-term persistence. The aim of the present work is to analyse how the spatial structure of the landscape and dispersal patterns of species (dispersal rate and average dispersal distance) affects metacommunity response to two disturbances: (i) increased mortality during dispersal and (ii) local species extinction. We analyse the disturbances both in isolation and in combination. Using a spatially and dynamically explicit metacommunity model, we find that the effect of dispersal on metacommunity persistence is two-sided: on the one hand, high dispersal significantly reduces the risk of bottom-up extinction cascades following the local removal of a species; on the other hand, when dispersal imposes a risk to the dispersing individuals, high dispersal increases extinction risks, especially when dispersal is global. Large-bodied species with long generation times at the highest trophic level are particularly vulnerable to extinction when dispersal involves a risk. This suggests that decreasing the mortality risk of dispersing individuals by improving the quality of the habitat matrix may greatly increase the robustness of metacommunities.

Roll-to-roll light directed electrophoretic deposition system and method

DOEpatents

Pascall, Andrew J.; Kuntz, Joshua

2017-06-06

A roll-to-roll light directed electrophoretic deposition system and method advances a roll of a flexible electrode web substrate along a roll-to-roll process path, where a material source is positioned to provide on the flexible electrode web substrate a thin film colloidal dispersion of electrically charged colloidal material dispersed in a fluid. A counter electrode is also positioned to come in contact with the thin film colloidal dispersion opposite the flexible electrode web substrate, where one of the counter electrode and the flexible electrode web substrate is a photoconductive electrode. A voltage source is connected to produce an electric potential between the counter electrode and the flexible electrode web substrate to induce electrophoretic deposition on the flexible electrode web substrate when the photoconductive electrode is rendered conductive, and a patterned light source is arranged to illuminate the photoconductive electrode with a light pattern and render conductive illuminated areas of the photoconductive electrode so that a patterned deposit of the electrically charged colloidal material is formed on the flexible electrode web substrate.

A new design methodology of obtaining wide band high gain broadband parametric source for infrared wavelength applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maji, Partha Sona; Roy Chaudhuri, Partha

In this article, we have presented a new design methodology of obtaining wide band parametric sources based on highly nonlinear chalcogenide material of As{sub 2}S{sub 3}. The dispersion profile of the photonic crystal fiber (PCF) has been engineered wisely by reducing the diameter of the second air-hole ring to have a favorable higher order dispersion parameter. The parametric gain dependence upon fiber length, pump power, and different pumping wavelengths has been investigated in detail. Based upon the nonlinear four wave mixing phenomenon, we are able to achieve a wideband parametric amplifier with peak gain of 29 dB with FWHM of ≈2000 nmmore » around the IR wavelength by proper tailoring of the dispersion profile of the PCF with a continuous wave Erbium (Er{sup 3+})-doped ZBLAN fiber laser emitting at 2.8 μm as the pump source with an average power of 5 W. The new design methodology will unleash a new dimension to the chalcogenide material based investigation for wavelength translation around IR wavelength band.« less

AERMOD: A DISPERSION MODEL FOR INDUSTRIAL SOURCE APPLICATIONS PART I: GENERAL MODEL FORMULATION AND BOUNDARY LAYER CHARACTERIZATION

EPA Science Inventory

The formulations of the AMS/EPA Regulatory Model Improvement Committee's applied air dispersion model (AERMOD) as related to the characterization of the planetary boundary layer are described. This is the first in a series of three articles. Part II describes the formulation of...

Using Rare Earth Elements (REE) to determine wind-driven soil dispersal from a point source

USDA-ARS?s Scientific Manuscript database

Although erosion of soil by water is a predictably directional process, the erosion of soil by wind is determined by wind direction on an event-wise basis. The wind-driven dispersal patterns of chemical constituents including natural soil components and anthropogenic contaminants are not well under...

Real-time ultrawide-band group delay profile monitoring through low-noise incoherent temporal interferometry.

PubMed

Park, Yongwoo; Malacarne, Antonio; Azaña, José

2011-02-28

A simple, highly accurate measurement technique for real-time monitoring of the group delay (GD) profiles of photonic dispersive devices over ultra-broad spectral bandwidths (e.g. an entire communication wavelength band) is demonstrated. The technique is based on time-domain self-interference of an incoherent light pulse after linear propagation through the device under test, providing a measurement wavelength range as wide as the source spectral bandwidth. Significant enhancement in the signal-to-noise ratio of the self-interference signal has been observed by use of a relatively low-noise incoherent light source as compared with the theoretical estimate for a white-noise light source. This fact combined with the use of balanced photo-detection has allowed us to significantly reduce the number of profiles that need to be averaged to reach a targeted GD measurement accuracy, thus achieving reconstruction of the device GD profile in real time. We report highly-accurate monitoring of (i) the group-delay ripple (GDR) profile of a 10-m long chirped fiber Bragg grating over the full C band (~42 nm), and (ii) the group velocity dispersion (GVD) and dispersion slope (DS) profiles of a ~2-km long dispersion compensating fiber module over an ~72-nm wavelength range, both captured at a 15 frames/s video rate update, with demonstrated standard deviations in the captured GD profiles as low as ~1.6 ps.

Estimation of the emission factors of PAHs by traffic with the model of atmospheric dispersion and deposition from heavy traffic road.

PubMed

Ozaki, N; Tokumitsu, H; Kojima, K; Kindaichi, T

2007-01-01

In order to consider the total atmospheric loadings of the PAHs (polycyclic aromatic hydrocarbons) from traffic activities, the emission factors of PAHs were estimated and from the obtained emission factors and vehicle transportation statistics, total atmospheric loadings were integrated and the loadings into the water body were estimated on a regional scale. The atmospheric concentration of PAHs was measured at the roadside of a road with heavy traffic in the Hiroshima area in Japan. The samplings were conducted in summer and winter. Atmospheric particulate matters (fine particle, 0.6-7 microm; coarse particle, over 7 microm) and their PAH concentration were measured. Also, four major emission sources (gasoline and diesel vehicle emissions, tire and asphalt debris) were assumed for vehicle transportation activities, the chemical mass balance method was applied and the source partitioning at the roadside was estimated. Furthermore, the dispersion of atmospheric particles from the vehicles was modelled and the emission factors of the sources were determined by the comparison to the chemical mass balance results. Based on emission factors derived from the modelling, an atmospheric dispersion model of nationwide scale (National Institute of Advanced Industrial Science and Technology - Atmospheric Dispersion Model for Exposure and Risk assessment) was applied, and the atmospheric concentration and loading to the ground were calculated for the Hiroshima Bay watershed area.

Multimodal approach to seismic pavement testing

USGS Publications Warehouse

Ryden, N.; Park, C.B.; Ulriksen, P.; Miller, R.D.

2004-01-01

A multimodal approach to nondestructive seismic pavement testing is described. The presented approach is based on multichannel analysis of all types of seismic waves propagating along the surface of the pavement. The multichannel data acquisition method is replaced by multichannel simulation with one receiver. This method uses only one accelerometer-receiver and a light hammer-source, to generate a synthetic receiver array. This data acquisition technique is made possible through careful triggering of the source and results in such simplification of the technique that it is made generally available. Multiple dispersion curves are automatically and objectively extracted using the multichannel analysis of surface waves processing scheme, which is described. Resulting dispersion curves in the high frequency range match with theoretical Lamb waves in a free plate. At lower frequencies there are several branches of dispersion curves corresponding to the lower layers of different stiffness in the pavement system. The observed behavior of multimodal dispersion curves is in agreement with theory, which has been validated through both numerical modeling and the transfer matrix method, by solving for complex wave numbers. ?? ASCE / JUNE 2004.

Modelling and estimating pollen movement in oilseed rape (Brassica napus) at the landscape scale using genetic markers.

PubMed

Devaux, C; Lavigne, C; Austerlitz, F; Klein, E K

2007-02-01

Understanding patterns of pollen movement at the landscape scale is important for establishing management rules following the release of genetically modified (GM) crops. We use here a mating model adapted to cultivated species to estimate dispersal kernels from the genotypes of the progenies of male-sterile plants positioned at different sampling sites within a 10 x 10-km oilseed rape production area. Half of the pollen clouds sampled by the male-sterile plants originated from uncharacterized pollen sources that could consist of both large volunteer and feral populations, and fields within and outside the study area. The geometric dispersal kernel was the most appropriate to predict pollen movement in the study area. It predicted a much larger proportion of long-distance pollination than previously fitted dispersal kernels. This best-fitting mating model underestimated the level of differentiation among pollen clouds but could predict its spatial structure. The estimation method was validated on simulated genotypic data, and proved to provide good estimates of both the shape of the dispersal kernel and the rate and composition of pollen issued from uncharacterized pollen sources. The best dispersal kernel fitted here, the geometric kernel, should now be integrated into models that aim at predicting gene flow at the landscape level, in particular between GM and non-GM crops.

The oil-dispersion bath in anthroposophic medicine--an integrative review.

PubMed

Büssing, Arndt; Cysarz, Dirk; Edelhäuser, Friedrich; Bornhöft, Gudrun; Matthiessen, Peter F; Ostermann, Thomas

2008-12-04

Anthroposophic medicine offers a variety of treatments, among others the oil-dispersion bath, developed in the 1930s by Werner Junge. Based on the phenomenon that oil and water do not mix and on recommendations of Rudolf Steiner, Junge developed a vortex mechanism which churns water and essential oils into a fine mist. The oil-covered droplets empty into a tub, where the patient immerses for 15-30 minutes. We review the current literature on oil-dispersion baths. The following databases were searched: Medline, Pubmed, Embase, AMED and CAMbase. The search terms were 'oil-dispersion bath' and 'oil bath', and their translations in German and French. An Internet search was also performed using Google Scholar, adding the search terms 'study' and 'case report' to the search terms above. Finally, we asked several experts for gray literature not listed in the above-mentioned databases. We included only articles which met the criterion of a clinical study or case report, and excluded theoretical contributions. Among several articles found in books, journals and other publications, we identified 1 prospective clinical study, 3 experimental studies (enrolling healthy individuals), 5 case reports, and 3 field-reports. In almost all cases, the studies described beneficial effects - although the methodological quality of most studies was weak. Main indications were internal/metabolic diseases and psychiatric/neurological disorders. Beyond the obvious beneficial effects of warm bathes on the subjective well-being, it remains to be clarified what the unique contribution of the distinct essential oils dispersed in the water can be. There is a lack of clinical studies exploring the efficacy of oil-dispersion baths. Such studies are recommended for the future.

The oil-dispersion bath in anthroposophic medicine – an integrative review

PubMed Central

Büssing, Arndt; Cysarz, Dirk; Edelhäuser, Friedrich; Bornhöft, Gudrun; Matthiessen, Peter F; Ostermann, Thomas

2008-01-01

Background Anthroposophic medicine offers a variety of treatments, among others the oil-dispersion bath, developed in the 1930s by Werner Junge. Based on the phenomenon that oil and water do not mix and on recommendations of Rudolf Steiner, Junge developed a vortex mechanism which churns water and essential oils into a fine mist. The oil-covered droplets empty into a tub, where the patient immerses for 15–30 minutes. We review the current literature on oil-dispersion baths. Methods The following databases were searched: Medline, Pubmed, Embase, AMED and CAMbase. The search terms were 'oil-dispersion bath' and 'oil bath', and their translations in German and French. An Internet search was also performed using Google Scholar, adding the search terms 'study' and 'case report' to the search terms above. Finally, we asked several experts for gray literature not listed in the above-mentioned databases. We included only articles which met the criterion of a clinical study or case report, and excluded theoretical contributions. Results Among several articles found in books, journals and other publications, we identified 1 prospective clinical study, 3 experimental studies (enrolling healthy individuals), 5 case reports, and 3 field-reports. In almost all cases, the studies described beneficial effects – although the methodological quality of most studies was weak. Main indications were internal/metabolic diseases and psychiatric/neurological disorders. Conclusion Beyond the obvious beneficial effects of warm bathes on the subjective well-being, it remains to be clarified what the unique contribution of the distinct essential oils dispersed in the water can be. There is a lack of clinical studies exploring the efficacy of oil-dispersion baths. Such studies are recommended for the future. PMID:19055811

Modelling of deposited black carbon with the Lagrangian particle dispersion model FLEXPART in backward mode

NASA Astrophysics Data System (ADS)

Eckhardt, Sabine; Cassiani, Massimo; Sollum, Espen; Evangeliou, Nikolaos; Stohl, Andreas

2017-04-01

Lagrangian particle dispersion models are popular tools to simulate the dispersion of trace gases, aerosols or radionuclides in the atmosphere. If they consider only linear processes, they are self-adjoint, i.e., they can be run forward and backward in time without changes to the source code. Backward simulations are very efficient if the number of receptors is smaller than the number of sources, and they are well suited to establish source-receptor (s-r) relationships for measurements of various trace substances in air. However, not only the air concentrations are of interest, but also the s-r relationships for deposition are important for interpreting measurement data. E.g., deposition of dust is measured regularly in ice cores, partly also as a proxy to understand changes in aridity in dust source regions. Contamination of snow by black carbon (BC) aerosols has recently become a hot topic because of the potential impact of BC on the snow albedo. To interpret such deposition measurements and study the sources of the deposited substance, it would be convenient to have a model that is capable of efficient s-r relationship calculations for such types of measurements. We present here the implementation of such an algorithm into the Lagrangian particle dispersion model FLEXPART, and test the new scheme by comparisons with results from forward simulations as well as comparisons with measurements. As an application, we analyse source regions for elemental carbon (EC) measured in snow over the years 2014-2016 in the Russian Arctic. Simulations using an annual constant black carbon inventory based on ECLIPSE V5 and GFED (Global Fire Emission Database), have been performed. The meteorological data used in the simulation are 3 hourly operational data from the European Centre of Medium Range Weather Forecast (ECMWF) on a 1 degree grid resolution and 138 vertical levels. The model is able to capture very well the measured concentrations. Gas flaring and residential/commercial combustion can be identified as the most important sources. High concentrations measured near the Ob River (up to 170 ng g-1) can be associated with air masses coming from Europe.

Study Design to Evaluate Mobile Source Emissions in the Near-Roadway Environment

EPA Science Inventory

In 2007, the U.S. Federal Highway Administration and U.S. Environmental Protection Agency entered into a collaborative agreement to study the near-road concentration and dispersion properties of several mobile source air toxics (MSATs) identified by the EP A 2001 Mobile Source Ai...

Estimation of the Cesium-137 Source Term from the Fukushima Daiichi Power Plant Using Air Concentration and Deposition Data

NASA Astrophysics Data System (ADS)

Winiarek, Victor; Bocquet, Marc; Duhanyan, Nora; Roustan, Yelva; Saunier, Olivier; Mathieu, Anne

2013-04-01

A major difficulty when inverting the source term of an atmospheric tracer dispersion problem is the estimation of the prior errors: those of the atmospheric transport model, those ascribed to the representativeness of the measurements, the instrumental errors, and those attached to the prior knowledge on the variables one seeks to retrieve. In the case of an accidental release of pollutant, and specially in a situation of sparse observability, the reconstructed source is sensitive to these assumptions. This sensitivity makes the quality of the retrieval dependent on the methods used to model and estimate the prior errors of the inverse modeling scheme. In Winiarek et al. (2012), we proposed to use an estimation method for the errors' amplitude based on the maximum likelihood principle. Under semi-Gaussian assumptions, it takes into account, without approximation, the positivity assumption on the source. We applied the method to the estimation of the Fukushima Daiichi cesium-137 and iodine-131 source terms using activity concentrations in the air. The results were compared to an L-curve estimation technique, and to Desroziers's scheme. Additionally to the estimations of released activities, we provided related uncertainties (12 PBq with a std. of 15 - 20 % for cesium-137 and 190 - 380 PBq with a std. of 5 - 10 % for iodine-131). We also enlightened that, because of the low number of available observations (few hundreds) and even if orders of magnitude were consistent, the reconstructed activities significantly depended on the method used to estimate the prior errors. In order to use more data, we propose to extend the methods to the use of several data types, such as activity concentrations in the air and fallout measurements. The idea is to simultaneously estimate the prior errors related to each dataset, in order to fully exploit the information content of each one. Using the activity concentration measurements, but also daily fallout data from prefectures and cumulated deposition data over a region lying approximately 150 km around the nuclear power plant, we can use a few thousands of data in our inverse modeling algorithm to reconstruct the Cesium-137 source term. To improve the parameterization of removal processes, rainfall fields have also been corrected using outputs from the mesoscale meteorological model WRF and ground station rainfall data. As expected, the different methods yield closer results as the number of data increases. Reference : Winiarek, V., M. Bocquet, O. Saunier, A. Mathieu (2012), Estimation of errors in the inverse modeling of accidental release of atmospheric pollutant : Application to the reconstruction of the cesium-137 and iodine-131 source terms from the Fukushima Daiichi power plant, J. Geophys. Res., 117, D05122, doi:10.1029/2011JD016932.

Selenium mobility and distribution in irrigated and nonirrigated alluvial soils

USGS Publications Warehouse

Fio, John L.; Fujii, Roger; Deverel, S.J.

1991-01-01

Dissolution and leaching of soil salts by irrigation water is a primary source of Se to shallow groundwater in the western San Joaquin Valley, California. In this study, the mobility and distribution of selenite and selenate in soils with different irrigation and drainage histories was evaluated using sorption experiments and an advection-dispersion model. The sorption studies showed that selenate (15–12400 µg Se L−1) is not adsorbed to soil, whereas selenite (10–5000 µg Se L−1) is rapidly adsorbed. The time lag between adsorption and desorption of selenite is considerable, indicating a dependence of reaction rate on reaction direction (hysteresis). Selenite adsorption and desorption isotherms were different, and both were described with the Freundlich equation. Model results and chemical analyses of extracts from the soil samples showed that selenite is resistant to leaching and therefore can represent a potential long-term source of Se to groundwater. In contrast, selenate behaves as a conservative constituent under alkaline and oxidized conditions and is easily leached from soil.

Conformal doping of topographic silicon structures using a radial line slot antenna plasma source

NASA Astrophysics Data System (ADS)

Ueda, Hirokazu; Ventzek, Peter L. G.; Oka, Masahiro; Horigome, Masahiro; Kobayashi, Yuuki; Sugimoto, Yasuhiro; Nozawa, Toshihisa; Kawakami, Satoru

2014-06-01

Fin extension doping for 10 nm front end of line technology requires ultra-shallow high dose conformal doping. In this paper, we demonstrate a new radial line slot antenna plasma source based doping process that meets these requirements. Critical to reaching true conformality while maintaining fin integrity is that the ion energy be low and controllable, while the dose absorption is self-limited. The saturated dopant later is rendered conformal by concurrent amorphization and dopant containing capping layer deposition followed by stabilization anneal. Dopant segregation assists in driving dopants from the capping layer into the sub silicon surface. Very high resolution transmission electron microscopy-Energy Dispersive X-ray spectroscopy, used to prove true conformality, was achieved. We demonstrate these results using an n-type arsenic based plasma doping process on 10 to 40 nm high aspect ratio fins structures. The results are discussed in terms of the different types of clusters that form during the plasma doping process.

The 2016 Al-Mishraq sulphur plant fire: Source and health risk area estimation

NASA Astrophysics Data System (ADS)

Björnham, Oscar; Grahn, Håkan; von Schoenberg, Pontus; Liljedahl, Birgitta; Waleij, Annica; Brännström, Niklas

2017-11-01

On October 20, 2016, Daesh (Islamic State) set fire to the sulphur production site Al-Mishraq as the battle of Mosul in northern Iraq became more intense. An extensive plume of toxic sulphur dioxide and hydrogen sulphide caused comprehensive casualties. The intensity of the SO2 release was reaching levels of minor volcanic eruptions and the plume was observed by several satellites. By investigation of the measurement data from instruments on the MetOp-A, MetOp-B, Aura and Soumi satellites we have estimated the time-dependent source term to 161 kilotonnes sulphur dioxide released into the atmosphere during seven days. A long-range dispersion model was utilized to simulate the atmospheric transport over the Middle East. The ground level concentrations predicted by the simulation were compared with observation from the Turkey National Air Quality Monitoring Network. Finally, the simulation data provided, using a probit analysis of the simulated data, an estimate of the health risk area that was compared to reported urgent medical treatments.

Discovery of long-distance gamete dispersal in a lichen-forming ascomycete.

PubMed

Ronnås, Cecilia; Werth, Silke; Ovaskainen, Otso; Várkonyi, Gergely; Scheidegger, Christoph; Snäll, Tord

2017-10-01

Accurate estimates of gamete and offspring dispersal range are required for the understanding and prediction of spatial population dynamics and species persistence. Little is known about gamete dispersal in fungi, especially in lichen-forming ascomycetes. Here, we estimate the dispersal functions of clonal propagules, gametes and ascospores of the epiphytic lichen Lobaria pulmonaria. We use hierarchical Bayesian parentage analysis, which integrates genetic and ecological information from multiannual colonization and dispersal source data collected in a large, old-growth forest landscape. The effective dispersal range of gametes is several hundred metres to kilometres from potential paternal individuals. By contrast, clonal propagules disperse only tens of metres, and ascospores disperse over several thousand metres. Our study reveals the dispersal distances of individual reproductive units; clonal propagules, gametes and ascospores, which is of great importance for a thorough understanding of the spatial dynamics of ascomycetes. Sexual reproduction occurs between distant individuals. However, whereas gametes and ascospores disperse over long distances, the overall rate of colonization of trees is low. Hence, establishment is the limiting factor for the colonization of new host trees by the lichen in old-growth landscapes. © 2017 The Authors. New Phytologist © 2017 New Phytologist Trust.

Detecting and analyzing soil phosphorus loss associated with critical source areas using a remote sensing approach.

PubMed

Lou, Hezhen; Yang, Shengtian; Zhao, Changsen; Shi, Liuhua; Wu, Linna; Wang, Yue; Wang, Zhiwei

2016-12-15

The detection of critical source areas (CSAs) is a key step in managing soil phosphorus (P) loss and preventing the long-term eutrophication of water bodies at regional scale. Most related studies, however, focus on a local scale, which prevents a clear understanding of the spatial distribution of CSAs for soil P loss at regional scale. Moreover, the continual, long-term variation in CSAs was scarcely reported. It is impossible to identify the factors driving the variation in CSAs, or to collect land surface information essential for CSAs detection, by merely using the conventional methodologies at regional scale. This study proposes a new regional-scale approach, based on three satellite sensors (ASTER, TM/ETM and MODIS), that were implemented successfully to detect CSAs at regional scale over 15years (2000-2014). The approach incorporated five factors (precipitation, slope, soil erosion, land use, soil total phosphorus) that drive soil P loss from CSAs. Results show that the average area of critical phosphorus source areas (CPSAs) was 15,056km 2 over the 15-year period, and it occupied 13.8% of the total area, with a range varying from 1.2% to 23.0%, in a representative, intensive agricultural area of China. In contrast to previous studies, we found that the locations of CSAs with P loss are spatially variable, and are more dispersed in their distribution over the long term. We also found that precipitation acts as a key driving factor in the variation of CSAs at regional scale. The regional-scale method can provide scientific guidance for managing soil phosphorus loss and preventing the long-term eutrophication of water bodies at regional scale, and shows great potential for exploring factors that drive the variation in CSAs at global scale. Copyright © 2016 Elsevier B.V. All rights reserved.

Identifying Patterns in the Weather of Europe for Source Term Estimation

NASA Astrophysics Data System (ADS)

Klampanos, Iraklis; Pappas, Charalambos; Andronopoulos, Spyros; Davvetas, Athanasios; Ikonomopoulos, Andreas; Karkaletsis, Vangelis

2017-04-01

During emergencies that involve the release of hazardous substances into the atmosphere the potential health effects on the human population and the environment are of primary concern. Such events have occurred in the past, most notably involving radioactive and toxic substances. Examples of radioactive release events include the Chernobyl accident in 1986, as well as the more recent Fukushima Daiichi accident in 2011. Often, the release of dangerous substances in the atmosphere is detected at locations different from the release origin. The objective of this work is the rapid estimation of such unknown sources shortly after the detection of dangerous substances in the atmosphere, with an initial focus on nuclear or radiological releases. Typically, after the detection of a radioactive substance in the atmosphere indicating the occurrence of an unknown release, the source location is estimated via inverse modelling. However, depending on factors such as the spatial resolution desired, traditional inverse modelling can be computationally time-consuming. This is especially true for cases where complex topography and weather conditions are involved and can therefore be problematic when timing is critical. Making use of machine learning techniques and the Big Data Europe platform1, our approach moves the bulk of the computation before any such event taking place, therefore allowing for rapid initial, albeit rougher, estimations regarding the source location. Our proposed approach is based on the automatic identification of weather patterns within the European continent. Identifying weather patterns has long been an active research field. Our case is differentiated by the fact that it focuses on plume dispersion patterns and these meteorological variables that affect dispersion the most. For a small set of recurrent weather patterns, we simulate hypothetical radioactive releases from a pre-known set of nuclear reactor locations and for different substance and temporal parameters, using the Java flavour of the Euratom-supported funded RODOS (Real-time On-line DecisiOn Support) system2 for off-site emergency management after nuclear accidents. Once dispersions have been pre-computed, and immediately after a detected release, the currently observed weather can be matched to the derived weather classes. Since each weather class corresponds to a different plume dispersion pattern, the closest classes to an unseen weather sample, say the current weather, are the most likely to lead us to the release origin. In addressing the above problem, we make use of multiple years of weather reanalysis data from NCAR's version3 of ECMWF's ERA-Interim4. To derive useful weather classes, we evaluate several algorithms, ranging from straightforward unsupervised clustering to more complex methods, including relevant neural-network algorithms, on multiple variables. Variables and feature sets, clustering algorithms and evaluation approaches are all dealt with and presented experimentally. The Big Data Europe platform allows for the implementation and execution of the above tasks in the cloud, in a scalable, robust and efficient way.

Toward quantitative forecasts of volcanic ash dispersal: Using satellite retrievals for optimal estimation of source terms

NASA Astrophysics Data System (ADS)

Zidikheri, Meelis J.; Lucas, Christopher; Potts, Rodney J.

2017-08-01

Airborne volcanic ash is a hazard to aviation. There is an increasing demand for quantitative forecasts of ash properties such as ash mass load to allow airline operators to better manage the risks of flying through airspace likely to be contaminated by ash. In this paper we show how satellite-derived mass load information at times prior to the issuance of the latest forecast can be used to estimate various model parameters that are not easily obtained by other means such as the distribution of mass of the ash column at the volcano. This in turn leads to better forecasts of ash mass load. We demonstrate the efficacy of this approach using several case studies.

Accurate finite difference methods for time-harmonic wave propagation

NASA Technical Reports Server (NTRS)

Harari, Isaac; Turkel, Eli

1994-01-01

Finite difference methods for solving problems of time-harmonic acoustics are developed and analyzed. Multidimensional inhomogeneous problems with variable, possibly discontinuous, coefficients are considered, accounting for the effects of employing nonuniform grids. A weighted-average representation is less sensitive to transition in wave resolution (due to variable wave numbers or nonuniform grids) than the standard pointwise representation. Further enhancement in method performance is obtained by basing the stencils on generalizations of Pade approximation, or generalized definitions of the derivative, reducing spurious dispersion, anisotropy and reflection, and by improving the representation of source terms. The resulting schemes have fourth-order accurate local truncation error on uniform grids and third order in the nonuniform case. Guidelines for discretization pertaining to grid orientation and resolution are presented.

Exact law for homogeneous compressible Hall magnetohydrodynamics turbulence

NASA Astrophysics Data System (ADS)

Andrés, N.; Galtier, S.; Sahraoui, F.

2018-01-01

We derive an exact law for three-dimensional (3D) homogeneous compressible isothermal Hall magnetohydrodynamic turbulence, without the assumption of isotropy. The Hall current is shown to introduce new flux and source terms that act at the small scales (comparable or smaller than the ion skin depth) to significantly impact the turbulence dynamics. The law provides an accurate means to estimate the energy cascade rate over a broad range of scales covering the magnetohydrodynamic inertial range and the sub-ion dispersive range in 3D numerical simulations and in in situ spacecraft observations of compressible turbulence. This work is particularly relevant to astrophysical flows in which small-scale density fluctuations cannot be ignored such as the solar wind, planetary magnetospheres, and the interstellar medium.

Solitonic Dispersive Hydrodynamics: Theory and Observation

NASA Astrophysics Data System (ADS)

Maiden, Michelle D.; Anderson, Dalton V.; Franco, Nevil A.; El, Gennady A.; Hoefer, Mark A.

2018-04-01

Ubiquitous nonlinear waves in dispersive media include localized solitons and extended hydrodynamic states such as dispersive shock waves. Despite their physical prominence and the development of thorough theoretical and experimental investigations of each separately, experiments and a unified theory of solitons and dispersive hydrodynamics are lacking. Here, a general soliton-mean field theory is introduced and used to describe the propagation of solitons in macroscopic hydrodynamic flows. Two universal adiabatic invariants of motion are identified that predict trapping or transmission of solitons by hydrodynamic states. The result of solitons incident upon smooth expansion waves or compressive, rapidly oscillating dispersive shock waves is the same, an effect termed hydrodynamic reciprocity. Experiments on viscous fluid conduits quantitatively confirm the soliton-mean field theory with broader implications for nonlinear optics, superfluids, geophysical fluids, and other dispersive hydrodynamic media.

40 CFR 171.2 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... to control the rate of dispersal, and droplet or particle size of a pesticide dispersed by the... pesticide which permits its use with other chemicals without undesirable results being caused by the... devices that shield against unintended exposure to pesticides. (22) The term regulated pest means a...

40 CFR 171.2 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... to control the rate of dispersal, and droplet or particle size of a pesticide dispersed by the... pesticide which permits its use with other chemicals without undesirable results being caused by the... devices that shield against unintended exposure to pesticides. (22) The term regulated pest means a...

40 CFR 171.2 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... to control the rate of dispersal, and droplet or particle size of a pesticide dispersed by the... pesticide which permits its use with other chemicals without undesirable results being caused by the... devices that shield against unintended exposure to pesticides. (22) The term regulated pest means a...

Dispersion modeling of polycyclic aromatic hydrocarbons from combustion of biomass and fossil fuels and production of coke in Tianjin, China.

PubMed

Tao, Shu; Li, Xinrong; Yang, Yu; Coveney, Raymond M; Lu, Xiaoxia; Chen, Haitao; Shen, Weiran

2006-08-01

A USEPA, procedure, ISCLT3 (Industrial Source Complex Long-Term), was applied to model the spatial distribution of polycyclic aromatic hydrocarbons (PAHs) emitted from various sources including coal, petroleum, natural gas, and biomass into the atmosphere of Tianjin, China. Benzo[a]pyrene equivalent concentrations (BaPeq) were calculated for risk assessment. Model results were provisionally validated for concentrations and profiles based on the observed data at two monitoring stations. The dominant emission sources in the area were domestic coal combustion, coke production, and biomass burning. Mainly because of the difference in the emission heights, the contributions of various sources to the average concentrations at receptors differ from proportions emitted. The shares of domestic coal increased from approximately 43% at the sources to 56% at the receptors, while the contributions of coking industry decreased from approximately 23% at the sources to 7% at the receptors. The spatial distributions of gaseous and particulate PAHs were similar, with higher concentrations occurring within urban districts because of domestic coal combustion. With relatively smaller contributions, the other minor sources had limited influences on the overall spatial distribution. The calculated average BaPeq value in air was 2.54 +/- 2.87 ng/m3 on an annual basis. Although only 2.3% of the area in Tianjin exceeded the national standard of 10 ng/m3, 41% of the entire population lives within this area.

VCSEL transmission at 10 Gb/s for 20 km single mode fiber WDM-PON without dispersion compensation or injection locking

NASA Astrophysics Data System (ADS)

Gibbon, T. B.; Prince, K.; Pham, T. T.; Tatarczak, A.; Neumeyr, C.; Rönneberg, E.; Ortsiefer, M.; Monroy, I. Tafur

2011-01-01

Vertical Cavity Surface Emitting Lasers (VCSELs) are extremely cost effective, energy efficient optical sources ideal for passive optical access networks. However, wavelength chirp and chromatic dispersion severely limit VCSEL performance at bit rates of 10 Gb/s and above. We experimentally show how off-center wavelength filtering of the VCSEL spectrum at an array waveguide grating can be used to mitigate the effect of chirp and the dispersion penalty. Transmission at 10 Gb/s VCSEL over 23.6 km of single mode fiber is experimentally demonstrated, with a dispersion penalty of only 2.9 dB. Simulated results are also presented which show that off-center wavelength filtering can extend the 10 Gb/s network reach from 11.7 km to 25.8 km for a 4 dB dispersion penalty. This allows for cheap and simple dispersion mitigation in next generation VCSEL-based optical access networks.

Abort-once-around entry dispersion corridor analysis. [for space shuttle reentry

NASA Technical Reports Server (NTRS)

Kyle, H. C.

1975-01-01

Abort-Once-Around (AOA) entry dispersion corridors were determined for Shuttle Mission 3A. These corridors are presented as plots of entry interface flight path angle versus range to target. The methods used to determine the corridors are discussed. Major dispersion sources are discussed and results presented. While specific trajectory inputs and constraints are subject to change, the dispersion corridors show the trends under consideration. The corridors presented show the delta V advantage of the two-burn over the one-burn AOA. The atmospheric dispersion study illustrates the need to target for the seasonal atmosphere. The 40 deg/30 deg angle of attack (alpha) (TPS design) profile did not provide adequate crossrange capability with worst case aerodynamic dispersions. This problem was alleviated with the change to a 38 deg/28 deg alpha profile. The backface temperatures calculated were generally higher than the present limits.

Method of Manufacturing Micro-Disperse Particles of Sodium Borohydride

DOEpatents

Kravitz, Stanley H.; Hecht, Andrew M.; Sylwester. Alan P.; Bell, Nelson S.

2008-09-23

A compact solid source of hydrogen gas, where the gas is generated by contacting water with micro-disperse particles of sodium borohydride in the presence of a catalyst, such as cobalt or ruthenium. The micro-disperse particles can have a substantially uniform diameter of 1-10 microns, and preferably about 3-5 microns. Ruthenium or cobalt catalytic nanoparticles can be incorporated in the micro-disperse particles of sodium borohydride, which allows a rapid and complete reaction to occur without the problems associated with caking and scaling of the surface by the reactant product sodium metaborate. A closed loop water management system can be used to recycle wastewater from a PEM fuel cell to supply water for reacting with the micro-disperse particles of sodium borohydride in a compact hydrogen gas generator. Capillary forces can wick water from a water reservoir into a packed bed of micro-disperse fuel particles, eliminating the need for using an active pump.

MAVEN Observations of Energy-Time Dispersed Electron Signatures in Martian Crustal Magnetic Fields

NASA Technical Reports Server (NTRS)

Harada, Y.; Mitchell, D. L.; Halekas, J. S.; McFadden, J. P.; Mazelle, C.; Connerney, J. E. P.; Espley, J.; Brain, D. A.; Larson, D. E.; Lillis, R. J.;

A landscape genetic analysis of important agricultural pest species in Tunisia: The whitefly Bemisia tabaci

PubMed Central

Fakhfakh, Hatem; Belkadhi, Mohamed Sadok

2017-01-01

Combining landscape ecology and genetics provides an excellent framework to appreciate pest population dynamics and dispersal. The genetic architectures of many species are always shaped by environmental constraints. Because little is known about the ecological and genetic traits of Tunisian whitefly populations, the main objective of this work is to highlight patterns of biodiversity, genetic structure and migration routes of this pest. We used nuclear microsatellite loci to analyze B. tabaci populations collected from various agricultural areas across the country and we determine their biotype status. Molecular data were subsequently interpreted in an ecological context supplied from a species distribution model to infer habitat suitability and hereafter the potential connection paths between sampling localities. An analysis of landscape resistance to B. tabaci genetic flow was thus applied to take into account habitat suitability, genetic relatedness and functional connectivity of habitats within a varied landscape matrix. We shed light on the occurrence of three geographically delineated genetic groups with high levels of genetic differentiation within each of them. Potential migration corridors of this pest were then established providing significant advances toward the understanding of genetic features and the dynamic dispersal of this pest. This study supports the hypothesis of a long-distance dispersal of B. tabaci followed by infrequent long-term isolations. The Inference of population sources and colonization routes is critical for the design and implementation of accurate management strategies against this pest. PMID:28972992

A landscape genetic analysis of important agricultural pest species in Tunisia: The whitefly Bemisia tabaci.

PubMed

Ben Abdelkrim, Ahmed; Hattab, Tarek; Fakhfakh, Hatem; Belkadhi, Mohamed Sadok; Gorsane, Faten

2017-01-01

Combining landscape ecology and genetics provides an excellent framework to appreciate pest population dynamics and dispersal. The genetic architectures of many species are always shaped by environmental constraints. Because little is known about the ecological and genetic traits of Tunisian whitefly populations, the main objective of this work is to highlight patterns of biodiversity, genetic structure and migration routes of this pest. We used nuclear microsatellite loci to analyze B. tabaci populations collected from various agricultural areas across the country and we determine their biotype status. Molecular data were subsequently interpreted in an ecological context supplied from a species distribution model to infer habitat suitability and hereafter the potential connection paths between sampling localities. An analysis of landscape resistance to B. tabaci genetic flow was thus applied to take into account habitat suitability, genetic relatedness and functional connectivity of habitats within a varied landscape matrix. We shed light on the occurrence of three geographically delineated genetic groups with high levels of genetic differentiation within each of them. Potential migration corridors of this pest were then established providing significant advances toward the understanding of genetic features and the dynamic dispersal of this pest. This study supports the hypothesis of a long-distance dispersal of B. tabaci followed by infrequent long-term isolations. The Inference of population sources and colonization routes is critical for the design and implementation of accurate management strategies against this pest.

Attempts to control clothes-borne infection in a burn unit, 2. Clothing routines in clinical use and the epidemiology of cross-colonization.

PubMed Central

Ransjö, U.

1979-01-01

Previous investigations have shown that cross-contamination in a burn unit is mainly clothes-borne. New barrier garments have been designed and tried experimentally. The aim of the present study was to investigate the effects of different clothing routines on cross-contamination. In a long-term study, the rates and routes of colonizations with Staphylococcus aureus, Streptococcus groups A, B, C, F, and G and Pseudomonas aeruginosa were examined. The exogenous colonization rates were, with S. aureus 77%, with Streptococcus species 52% and with Ps. aeruginosa 32%. The colonization rate with Ps. aeruginosa was higher in patients with larger burns. Patients dispersed Streptococcus and Ps. aeruginosa as well as S. aureus into the air of their rooms in considerable amounts, but dispersers were not more important as sources of cross-colonization than non-dispersers. In comparison of clothing routines, there was no difference in overall colonization rates. The newly designed barrier garment that was made from apparently particle-tight material did not reduce the transfer of bacteria from patient to patient. A less rigid routine than that previously used did not increase the risk of cross-contamination. A thorough change of barrier dress after close contact nursing delayed the first exogenous S. aureus colonization from day 6 to day 14 after admission. This routine might be recommended for clinical use. Otherwise, methods must be developed for adequate selection of materials intended for barrier garments. Images Plate 1 PMID:109498

Population connectivity of deep-sea corals: Chapter 12

USGS Publications Warehouse

Morrison, Cheryl L.; Baco, Amy; Nizinski, Martha S.; Coykendall, D. Katharine; Demopoulos, Amanda W. J.; Cho, Walter; Shank, Tim

2015-01-01

Identifying the scale of dispersal among habitats has been a challenge in marine ecology for decades (Grantham et al., 2003; Kinlan & Gaines, 2003; Hixon, 2011). Unlike terrestrial habitats in which barriers to dispersal may be obvious (e.g. mountain ranges, rivers), few absolute barriers to dispersal are recognizable in the sea. Additionally, most marine species have complex life cycles in which juveniles are more mobile than adults. As such, the dynamics of populations may involve processes in distant habitats that are coupled by a transport mechanism. Studies of population connectivity try to quantify the transport, or dispersal of individuals, among geographically separated populations. For benthic marine species, such as corals and demersal fishes, colonization of new populations occurs primarily by dispersal of larvae (Figure 1; Shank, 2010). Successful dispersal and recruitment, followed by maturation and reproduction of these new migrants ensures individuals contribute to the gene pool (Hedgecock, 2007). Thus, successful dispersal links and cohesively maintains spatially separated sub-populations. At shorter time scales (10-100s years), connectivity regulates community structure by influencing the genetic composition, diversity and demographic stability of the population, whereas at longer time scales (1000s years), geographic distributions are affected (McClain and Hardy, 2010). Alternatively, populations may become extinct or speciation may occur if connectivity ceases (Cowen et al., 2007). Therefore, the genetic exchange of individuals between populations is fundamental to the short-term resilience and long-term maintenance of the species. However, for the vast majority of marine species, population connectivity remains poorly understood.

Seed dispersal potential of Asian elephants

NASA Astrophysics Data System (ADS)

Harich, Franziska K.; Treydte, Anna C.; Ogutu, Joseph O.; Roberts, John E.; Savini, Chution; Bauer, Jan M.; Savini, Tommaso

2016-11-01

Elephants, the largest terrestrial mega-herbivores, play an important ecological role in maintaining forest ecosystem diversity. While several plant species strongly rely on African elephants (Loxodonta africana; L. cyclotis) as seed dispersers, little is known about the dispersal potential of Asian elephants (Elephas maximus). We examined the effects of elephant fruit consumption on potential seed dispersal using the example of a tree species with mega-faunal characteristics, Dillenia indica L., in Thailand. We conducted feeding trials with Asian elephants to quantify seed survival and gut passage times (GPT). In total, 1200 ingested and non-ingested control seeds were planted in soil and in elephant dung to quantify differences in germination rates in terms of GPT and dung treatment. We used survival analysis as a novel approach to account for the right-censored nature of the data obtained from germination experiments. The average seed survival rate was 79% and the mean GPT was 35 h. The minimum and maximum GPT were 20 h and 72 h, respectively. Ingested seeds were significantly more likely to germinate and to do so earlier than non-ingested control seeds (P = 0.0002). Seeds with the longest GPT displayed the highest germination success over time. Unexpectedly, seeds planted with dung had longer germination times than those planted without. We conclude that D. indica does not solely depend on but benefits from dispersal by elephants. The declining numbers of these mega-faunal seed dispersers might, therefore, have long-term negative consequences for the recruitment and dispersal dynamics of populations of certain tree species.

Constraints on short-term mantle rheology from the J2 observation and the dispersion of the 18.6 y tidal Love number

NASA Technical Reports Server (NTRS)

Sabadini, R.; Yuen, D. A.; Widmer, R.

1985-01-01

Information derived from data recently acquired from the LAGEOS satellite is used to place some constraints on the rheological parameters of short-term mantle rheology. The validity of Lambeck and Nakiboglu's (1983) rheological model is assessed by formally developing an expression for the transformed shear modulus using a truncated retardation spectrum. This analytical formula is used to show that the parameters of the above mentioned model are not consistent at all with the amount of anelastic dispersion expected in the Chandler wobble and with the attenuation of seismic normal modes. The feasibility of a standard linear solid (SLS) rheology operating over intermediate timescales between 1 and 100 yr is investigated to determine whether the tidal dispersion at 18.6 yr can be explained by this model. An attempt is made to place some constraints on the parameters of the SLS model and the nature of short-term mantle rheology for timescales of less than 100 yr is discussed.

Assessing implicit models for nonpolar mean solvation forces: The importance of dispersion and volume terms

PubMed Central

Wagoner, Jason A.; Baker, Nathan A.

2006-01-01

Continuum solvation models provide appealing alternatives to explicit solvent methods because of their ability to reproduce solvation effects while alleviating the need for expensive sampling. Our previous work has demonstrated that Poisson-Boltzmann methods are capable of faithfully reproducing polar explicit solvent forces for dilute protein systems; however, the popular solvent-accessible surface area model was shown to be incapable of accurately describing nonpolar solvation forces at atomic-length scales. Therefore, alternate continuum methods are needed to reproduce nonpolar interactions at the atomic scale. In the present work, we address this issue by supplementing the solvent-accessible surface area model with additional volume and dispersion integral terms suggested by scaled particle models and Weeks–Chandler–Andersen theory, respectively. This more complete nonpolar implicit solvent model shows very good agreement with explicit solvent results and suggests that, although often overlooked, the inclusion of appropriate dispersion and volume terms are essential for an accurate implicit solvent description of atomic-scale nonpolar forces. PMID:16709675

Criteria for Yielding of Dispersion-Strengthened Alloys

NASA Technical Reports Server (NTRS)

Ansell, G. S.; Lenel, F. V.

1960-01-01

A dislocation model is presented in order to account for the yield behavior of alloys with a finely dispersed second-phase. The criteria for yielding used in the model, is that appreciable yielding occurs in these alloys when the shear stress due to piled-up groups of dislocations is sufficient to fracture or plastically deform the dispersed second-phase particles, relieving the back stress on the dislocation sources. Equations derived on the basis of this model, predict that the yield stress of the alloys varies as the reciprocal square root of the mean free path between dispersed particles. Experimental data is presented for several SAP-Type alloys, precipitation-hardened alloys and steels which are in good agreement with the yield strength variation as a function of dispersion spacing predicted by this theoretical treatment.

RANS modeling of scalar dispersion from localized sources within a simplified urban-area model

NASA Astrophysics Data System (ADS)

Rossi, Riccardo; Capra, Stefano; Iaccarino, Gianluca

2011-11-01

The dispersion of a passive scalar downstream a localized source within a simplified urban-like geometry is examined by means of RANS scalar flux models. The computations are conducted under conditions of neutral stability and for three different incoming wind directions (0°, 45°, 90°) at a roughness Reynolds number of Ret = 391. A Reynolds stress transport model is used to close the flow governing equations whereas both the standard eddy-diffusivity closure and algebraic flux models are employed to close the transport equation for the passive scalar. The comparison with a DNS database shows improved reliability from algebraic scalar flux models towards predicting both the mean concentration and the plume structure. Since algebraic flux models do not increase substantially the computational effort, the results indicate that the use of tensorial-diffusivity can be promising tool for dispersion simulations for the urban environment.

Low power generation of equalized broadband CW supercontinua using a novel technique incorporating modulation instability of line broadened pump

NASA Astrophysics Data System (ADS)

Prakash, Roopa; Choudhury, Vishal; Arun, S.; Supradeepa, V. R.

2018-02-01

Continuous-wave(CW) supercontinuum sources find applications in various domains such as imaging, spectroscopy, test and measurement. They are generated by pumping an optical fiber with a CW laser in the anomalous-dispersion region close to its zero-dispersion wavelength. Modulation instability(MI) sidebands are created, and further broadened and equalized by additional nonlinear processes generating the supercontinuum. This necessitates high optical powers and at lower powers, only MI sidebands can be seen without the formation of the supercontinuum. Obtaining a supercontinuum at low, easily manageable optical powers is attractive for many applications, but current techniques cannot achieve this. In this work, we propose a new mechanism for low power supercontinuum generation utilizing the modified MI gain spectrum for a line-broadened, decorrelated pump. A novel two-stage generation mechanism is demonstrated, where the first stage constituting standard telecom fiber slightly broadens the input pump linewidth. However, this process in the presence of dispersion, acts to de-correlate the different spectral components of the pump signal. When this is sent through highly nonlinear fiber near its zero-dispersion wavelength, the shape of the MI gain spectrum is modified, and this process naturally results in the generation of a broadband, equalized supercontinuum source at much lower powers than possible using conventional single stage spectral broadening. Here, we demonstrate a 0.5W supercontinuum source pumped using a 4W Erbium-Ytterbium co-doped fiber laser with a bandwidth spanning from 1300nm to 2000nm. We also demonstrate an interesting behaviour of this technique of relative insensitivity to the pump wavelength vis-a-vis zero-dispersion wavelength of the fiber.

Inference of emission rates from multiple sources using Bayesian probability theory.

PubMed

Yee, Eugene; Flesch, Thomas K

2010-03-01

The determination of atmospheric emission rates from multiple sources using inversion (regularized least-squares or best-fit technique) is known to be very susceptible to measurement and model errors in the problem, rendering the solution unusable. In this paper, a new perspective is offered for this problem: namely, it is argued that the problem should be addressed as one of inference rather than inversion. Towards this objective, Bayesian probability theory is used to estimate the emission rates from multiple sources. The posterior probability distribution for the emission rates is derived, accounting fully for the measurement errors in the concentration data and the model errors in the dispersion model used to interpret the data. The Bayesian inferential methodology for emission rate recovery is validated against real dispersion data, obtained from a field experiment involving various source-sensor geometries (scenarios) consisting of four synthetic area sources and eight concentration sensors. The recovery of discrete emission rates from three different scenarios obtained using Bayesian inference and singular value decomposition inversion are compared and contrasted.

Bayesian probabilistic approach for inverse source determination from limited and noisy chemical or biological sensor concentration measurements

NASA Astrophysics Data System (ADS)

Yee, Eugene

2007-04-01

Although a great deal of research effort has been focused on the forward prediction of the dispersion of contaminants (e.g., chemical and biological warfare agents) released into the turbulent atmosphere, much less work has been directed toward the inverse prediction of agent source location and strength from the measured concentration, even though the importance of this problem for a number of practical applications is obvious. In general, the inverse problem of source reconstruction is ill-posed and unsolvable without additional information. It is demonstrated that a Bayesian probabilistic inferential framework provides a natural and logically consistent method for source reconstruction from a limited number of noisy concentration data. In particular, the Bayesian approach permits one to incorporate prior knowledge about the source as well as additional information regarding both model and data errors. The latter enables a rigorous determination of the uncertainty in the inference of the source parameters (e.g., spatial location, emission rate, release time, etc.), hence extending the potential of the methodology as a tool for quantitative source reconstruction. A model (or, source-receptor relationship) that relates the source distribution to the concentration data measured by a number of sensors is formulated, and Bayesian probability theory is used to derive the posterior probability density function of the source parameters. A computationally efficient methodology for determination of the likelihood function for the problem, based on an adjoint representation of the source-receptor relationship, is described. Furthermore, we describe the application of efficient stochastic algorithms based on Markov chain Monte Carlo (MCMC) for sampling from the posterior distribution of the source parameters, the latter of which is required to undertake the Bayesian computation. The Bayesian inferential methodology for source reconstruction is validated against real dispersion data for two cases involving contaminant dispersion in highly disturbed flows over urban and complex environments where the idealizations of horizontal homogeneity and/or temporal stationarity in the flow cannot be applied to simplify the problem. Furthermore, the methodology is applied to the case of reconstruction of multiple sources.

Offner stretcher aberrations revisited to compensate material dispersion

NASA Astrophysics Data System (ADS)

Vyhlídka, Štěpán; Kramer, Daniel; Meadows, Alexander; Rus, Bedřich

2018-05-01

We present simple analytical formulae for the calculation of the spectral phase and residual angular dispersion of an ultrashort pulse propagating through the Offner stretcher. Based on these formulae, we show that the radii of curvature of both convex and concave mirrors in the Offner triplet can be adapted to tune the fourth order dispersion term of the spectral phase of the pulse. As an example, a single-grating Offner stretcher design suitable for the suppression of material dispersion in the Ti:Sa PALS laser system is proposed. The results obtained by numerical raytracing well match those calculated from the analytical formulae.

Climate-driven spatial dynamics of plague among prairie dog colonies.

PubMed

Snäll, T; O'Hara, R B; Ray, C; Collinge, S K

2008-02-01

We present a Bayesian hierarchical model for the joint spatial dynamics of a host-parasite system. The model was fitted to long-term data on regional plague dynamics and metapopulation dynamics of the black-tailed prairie dog, a declining keystone species of North American prairies. The rate of plague transmission between colonies increases with increasing precipitation, while the rate of infection from unknown sources decreases in response to hot weather. The mean annual dispersal distance of plague is about 10 km, and topographic relief reduces the transmission rate. Larger colonies are more likely to become infected, but colony area does not affect the infectiousness of colonies. The results suggest that prairie dog movements do not drive the spread of plague through the landscape. Instead, prairie dogs are useful sentinels of plague epizootics. Simulations suggest that this model can be used for predicting long-term colony and plague dynamics as well as for identifying which colonies are most likely to become infected in a specific year.

Molybdenum enhanced low-temperature deposition of crystalline silicon nitride

DOEpatents

Lowden, Richard A.

1994-01-01

A process for chemical vapor deposition of crystalline silicon nitride which comprises the steps of: introducing a mixture of a silicon source, a molybdenum source, a nitrogen source, and a hydrogen source into a vessel containing a suitable substrate; and thermally decomposing the mixture to deposit onto the substrate a coating comprising crystalline silicon nitride containing a dispersion of molybdenum silicide.

Spatial seed and pollen games: dispersal, sex allocation, and the evolution of dioecy.

PubMed

Fromhage, Lutz; Kokko, Hanna

2010-09-01

The evolutionary forces shaping within- and across-species variation in the investment in male and female sex function are still incompletely understood. Despite earlier suggestions that in plants the evolution or cosexuality vs. dioecy, as well as sex allocation among cosexuals, is affected by seed and pollen dispersal, no formal model has explicitly used dispersal distances to address this problem. Here, we present a game-theory model as well as a simulation study that fills in this gap. Our model predicts that dioecy should evolve if seeds and pollen disperse widely and that sex allocation among cosexuals should be biased towards whichever sex function produces more widely dispersing units. Dispersal limitations stabilize cosexuality by reinforcing competition between spatially clumped dispersal units from the same source, leading to saturating fitness returns that render sexual specialization unprofitable. However, limited pollen dispersal can also increase the risk of selfing, thus potentially selecting for dioecy as an outbreeding mechanism. Finally, we refute a recent claim that cosexuals should always invest equally in both sex functions.

Shocks and finite-time singularities in Hele-Shaw flow

DOE Office of Scientific and Technical Information (OSTI.GOV)

Teodorescu, Razvan; Wiegmann, P; Lee, S-y

Hele-Shaw flow at vanishing surface tension is ill-defined. In finite time, the flow develops cusplike singularities. We show that the ill-defined problem admits a weak dispersive solution when singularities give rise to a graph of shock waves propagating in the viscous fluid. The graph of shocks grows and branches. Velocity and pressure jump across the shock. We formulate a few simple physical principles which single out the dispersive solution and interpret shocks as lines of decompressed fluid. We also formulate the dispersive solution in algebro-geometrical terms as an evolution of Krichever-Boutroux complex curve. We study in details the most genericmore » (2,3) cusp singularity which gives rise to an elementary branching event. This solution is self-similar and expressed in terms of elliptic functions.« less

Comparison between conventional biofilters and biotrickling filters applied to waste bio-drying in terms of atmospheric dispersion and air quality.

PubMed

Schiavon, Marco; Ragazzi, Marco; Torretta, Vincenzo; Rada, Elena Cristina

2016-01-01

Biofiltration has been widely applied to remove odours and volatile organic compounds (VOCs) from industrial off-gas and mechanical-biological waste treatments. However, conventional open biofilters cannot guarantee an efficient dispersion of air pollutants emitted into the atmosphere. The aim of this paper is to compare conventional open biofilters with biotrickling filters (BTFs) in terms of VOC dispersion in the atmosphere and air quality in the vicinity of a hypothetical municipal solid waste bio-drying plant. Simulations of dispersion were carried out regarding two VOCs of interest due to their impact in terms of odours and cancer risk: dimethyl disulphide and benzene, respectively. The use of BTFs, instead of conventional biofilters, led to significant improvements in the odour impact and the cancer risk: when adopting BTFs instead of an open biofilter, the area with an odour concentration > 1 OU m(-3) and a cancer risk > 10(-6) was reduced by 91.6% and 95.2%, respectively. When replacing the biofilter with BTFs, the annual mean concentrations of odorants and benzene decreased by more than 90% in the vicinity of the plant. These improvements are achieved above all because of the higher release height of BTFs and the higher velocity of the outgoing air flow.

City scale pollen concentration variability

NASA Astrophysics Data System (ADS)

van der Molen, Michiel; van Vliet, Arnold; Krol, Maarten

2016-04-01

Pollen are emitted in the atmosphere both in the country-side and in cities. Yet the majority of the population is exposed to pollen in cities. Allergic reactions may be induced by short-term exposure to pollen. This raises the question how variable pollen concentration in cities are in temporally and spatially, and how much of the pollen in cities are actually produced in the urban region itself. We built a high resolution (1 × 1 km) pollen dispersion model based on WRF-Chem to study a city's pollen budget and the spatial and temporal variability in concentration. It shows that the concentrations are highly variable, as a result of source distribution, wind direction and boundary layer mixing, as well as the release rate as a function of temperature, turbulence intensity and humidity. Hay Fever Forecasts based on such high resolution emission and physical dispersion modelling surpass traditional hay fever warning methods based on temperature sum methods. The model gives new insights in concentration variability, personal and community level exposure and prevention. The model will be developped into a new forecast tool to serve allergic people to minimize their exposure and reduce nuisance, coast of medication and sick leave. This is an innovative approach in hay fever warning systems.

Hydrodeoxygenation of water-insoluble bio-oil to alkanes using a highly dispersed Pd-Mo catalyst.

PubMed

Duan, Haohong; Dong, Juncai; Gu, Xianrui; Peng, Yung-Kang; Chen, Wenxing; Issariyakul, Titipong; Myers, William K; Li, Meng-Jung; Yi, Ni; Kilpatrick, Alexander F R; Wang, Yu; Zheng, Xusheng; Ji, Shufang; Wang, Qian; Feng, Junting; Chen, Dongliang; Li, Yadong; Buffet, Jean-Charles; Liu, Haichao; Tsang, Shik Chi Edman; O'Hare, Dermot

2017-09-19

Bio-oil, produced by the destructive distillation of cheap and renewable lignocellulosic biomass, contains high energy density oligomers in the water-insoluble fraction that can be utilized for diesel and valuable fine chemicals productions. Here, we show an efficient hydrodeoxygenation catalyst that combines highly dispersed palladium and ultrafine molybdenum phosphate nanoparticles on silica. Using phenol as a model substrate this catalyst is 100% effective and 97.5% selective for hydrodeoxygenation to cyclohexane under mild conditions in a batch reaction; this catalyst also demonstrates regeneration ability in long-term continuous flow tests. Detailed investigations into the nature of the catalyst show that it combines hydrogenation activity of Pd and high density of both Brønsted and Lewis acid sites; we believe these are key features for efficient catalytic hydrodeoxygenation behavior. Using a wood and bark-derived feedstock, this catalyst performs hydrodeoxygenation of lignin, cellulose, and hemicellulose-derived oligomers into liquid alkanes with high efficiency and yield.Bio-oil is a potential major source of renewable fuels and chemicals. Here, the authors report a palladium-molybdenum mixed catalyst for the selective hydrodeoxygenation of water-insoluble bio-oil to mixtures of alkanes with high carbon yield.

Dispersion characteristic of photoluminescence decay times of phosphor YAG: Ce, Gd

NASA Astrophysics Data System (ADS)

Lisitsyn, V. M.; Ju, Yangyang; Stepanov, S. A.; Soschin, N. M.

2017-05-01

The dispersion of the characteristic decay times of gadolinium co-doped yttrium aluminum garnet doped with cerium phosphors were studied. In the present work, an ultraviolet semiconductor laser (λem=375 nm, τ = 1 ns) was used as excitation source for measuring kinetics characteristics of phosphor groups based on YAG with different content of cerium.

Poisson Regression Analysis of Illness and Injury Surveillance Data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Frome E.L., Watkins J.P., Ellis E.D.

2012-12-12

The Department of Energy (DOE) uses illness and injury surveillance to monitor morbidity and assess the overall health of the work force. Data collected from each participating site include health events and a roster file with demographic information. The source data files are maintained in a relational data base, and are used to obtain stratified tables of health event counts and person time at risk that serve as the starting point for Poisson regression analysis. The explanatory variables that define these tables are age, gender, occupational group, and time. Typical response variables of interest are the number of absences duemore » to illness or injury, i.e., the response variable is a count. Poisson regression methods are used to describe the effect of the explanatory variables on the health event rates using a log-linear main effects model. Results of fitting the main effects model are summarized in a tabular and graphical form and interpretation of model parameters is provided. An analysis of deviance table is used to evaluate the importance of each of the explanatory variables on the event rate of interest and to determine if interaction terms should be considered in the analysis. Although Poisson regression methods are widely used in the analysis of count data, there are situations in which over-dispersion occurs. This could be due to lack-of-fit of the regression model, extra-Poisson variation, or both. A score test statistic and regression diagnostics are used to identify over-dispersion. A quasi-likelihood method of moments procedure is used to evaluate and adjust for extra-Poisson variation when necessary. Two examples are presented using respiratory disease absence rates at two DOE sites to illustrate the methods and interpretation of the results. In the first example the Poisson main effects model is adequate. In the second example the score test indicates considerable over-dispersion and a more detailed analysis attributes the over-dispersion to extra-Poisson variation. The R open source software environment for statistical computing and graphics is used for analysis. Additional details about R and the data that were used in this report are provided in an Appendix. Information on how to obtain R and utility functions that can be used to duplicate results in this report are provided.« less

Sources and dispersal of land-based runoff from small Hawaiian drainages to a coral reef: Insights from geochemical signatures

NASA Astrophysics Data System (ADS)

Takesue, Renee K.; Storlazzi, Curt D.

2017-03-01

Land-based sediment and contaminant runoff is a major threat to coral reefs, and runoff reduction efforts would benefit from knowledge of specific runoff sources. Geochemical signatures of small drainage basins were determined in the fine fraction of soil and sediment, then used in the nearshore region of a coral reef-fringed urban embayment on southeast Oahu, Hawaii, to describe sources and dispersal of land-based runoff. The sedimentary rare earth element ratio (La/Yb)N showed a clear distinction between the two main rock types in the overall contributing area, tholeiitic and alkalic olivine basalt. Based on this geochemical signature it was apparent that the majority of terrigenous sediment on the reef flat originated from geologically old tholeiitic drainages. Sediment from one of five tholeiitic drainages had a distinct geochemical signature, and sediment with this signature was dispersed on the reef flat 2 km west and 150 m offshore of the contributing basin. Sediment and the anthropogenic metals Cd, Pb, and Zn were entrained in runoff from the most heavily urbanized region of the watershed. Although anthropogenic Cd and Zn had localized distributions close to shore, anthropogenic Pb was found associated with fine sediment on the westernmost part of the reef flat and 400 m offshore, illustrating how trade-wind-driven sediment transport can increase the scale of runoff impacts to nearshore communities. Our findings show that sediment geochemical signatures can provide insights about the source and dispersal of land-based runoff in shallow coastal environments. The application of such knowledge to watershed management and habitat remediation efforts can aid in the protection and restoration of runoff-impacted coastal ecosystems worldwide.

Sources and dispersal of land-based runoff from small Hawaiian drainages to a coral reef: Insights from geochemical signatures

USGS Publications Warehouse

Takesue, Renee K.; Storlazzi, Curt

2017-01-01

Land-based sediment and contaminant runoff is a major threat to coral reefs, and runoff reduction efforts would benefit from knowledge of specific runoff sources. Geochemical signatures of small drainage basins were determined in the fine fraction of soil and sediment, then used in the nearshore region of a coral reef-fringed urban embayment on southeast Oahu, Hawaii, to describe sources and dispersal of land-based runoff. The sedimentary rare earth element ratio (La/Yb)N showed a clear distinction between the two main rock types in the overall contributing area, tholeiitic and alkalic olivine basalt. Based on this geochemical signature it was apparent that the majority of terrigenous sediment on the reef flat originated from geologically old tholeiitic drainages. Sediment from one of five tholeiitic drainages had a distinct geochemical signature, and sediment with this signature was dispersed on the reef flat 2 km west and 150 m offshore of the contributing basin. Sediment and the anthropogenic metals Cd, Pb, and Zn were entrained in runoff from the most heavily urbanized region of the watershed. Although anthropogenic Cd and Zn had localized distributions close to shore, anthropogenic Pb was found associated with fine sediment on the westernmost part of the reef flat and 400 m offshore, illustrating how trade-wind-driven sediment transport can increase the scale of runoff impacts to nearshore communities. Our findings show that sediment geochemical signatures can provide insights about the source and dispersal of land-based runoff in shallow coastal environments. The application of such knowledge to watershed management and habitat remediation efforts can aid in the protection and restoration of runoff-impacted coastal ecosystems worldwide.

Volcanic eruption source parameters from active and passive microwave sensors

NASA Astrophysics Data System (ADS)

Montopoli, Mario; Marzano, Frank S.; Cimini, Domenico; Mereu, Luigi

2016-04-01

It is well known, in the volcanology community, that precise information of the source parameters characterising an eruption are of predominant interest for the initialization of the Volcanic Transport and Dispersion Models (VTDM). Source parameters of main interest would be the top altitude of the volcanic plume, the flux of the mass ejected at the emission source, which is strictly related to the cloud top altitude, the distribution of volcanic mass concentration along the vertical column as well as the duration of the eruption and the erupted volume. Usually, the combination of a-posteriori field and numerical studies allow constraining the eruption source parameters for a given volcanic event thus making possible the forecast of ash dispersion and deposition from future volcanic eruptions. So far, remote sensors working at visible and infrared channels (cameras and radiometers) have been mainly used to detect, track and provide estimates of the concentration content and the prevailing size of the particles propagating within the ash clouds up to several thousand of kilometres far from the source as well as track back, a-posteriori, the accuracy of the VATDM outputs thus testing the initial choice made for the source parameters. Acoustic wave (infrasound) and microwave fixed scan radar (voldorad) were also used to infer source parameters. In this work we want to put our attention on the role of sensors operating at microwave wavelengths as complementary tools for the real time estimations of source parameters. Microwaves can benefit of the operability during night and day and a relatively negligible sensitivity to the presence of clouds (non precipitating weather clouds) at the cost of a limited coverage and larger spatial resolution when compared with infrared sensors. Thanks to the aforementioned advantages, the products from microwaves sensors are expected to be sensible mostly to the whole path traversed along the tephra cloud making microwaves particularly appealing for estimates close to the volcano emission source. Near the source the cloud optical thickness is expected to be large enough to induce saturation effects at the infrared sensor receiver thus vanishing the brightness temperature difference methods for the ash cloud identification. In the light of the introduction above, some case studies at Eyjafjallajökull 2010 (Iceland), Etna (Italy) and Calbuco (Cile), on 5-10 May 2010, 23rd Nov., 2013 and 23 Apr., 2015, respectively, are analysed in terms of source parameter estimates (manly the cloud top and mass flax rate) from ground based microwave weather radar (9.6 GHz) and satellite Low Earth Orbit microwave radiometers (50 - 183 GH). A special highlight will be given to the advantages and limitations of microwave-related products with respect to more conventional tools.

Nontronite Particle Aggregation Induced by Microbial Fe(III) Reduction and Exopolysaccharide Production

DTIC Science & Technology

2007-01-01

polymers to achieve desired properties (such Chenu el al., 1979; Kimn el al., 2005). Among these as aggregation. dispersion ) without any structural...performed with and without Na pyrophosphate as a term ’aggregation’ broadly to include all processes that dispersant (25 mM) with shaking in a water...coagulation, at 25 mM was found to be optimal to disperse individual flocculation, agglutination, etc.). The results of this clay particles without

Utilization of 134Cs/137Cs in the environment to identify the reactor units that caused atmospheric releases during the Fukushima Daiichi accident

NASA Astrophysics Data System (ADS)

Chino, Masamichi; Terada, Hiroaki; Nagai, Haruyasu; Katata, Genki; Mikami, Satoshi; Torii, Tatsuo; Saito, Kimiaki; Nishizawa, Yukiyasu

2016-08-01

The Fukushima Daiichi nuclear power reactor units that generated large amounts of airborne discharges during the period of March 12-21, 2011 were identified individually by analyzing the combination of measured 134Cs/137Cs depositions on ground surfaces and atmospheric transport and deposition simulations. Because the values of 134Cs/137Cs are different in reactor units owing to fuel burnup differences, the 134Cs/137Cs ratio measured in the environment was used to determine which reactor unit ultimately contaminated a specific area. Atmospheric dispersion model simulations were used for predicting specific areas contaminated by each dominant release. Finally, by comparing the results from both sources, the specific reactor units that yielded the most dominant atmospheric release quantities could be determined. The major source reactor units were Unit 1 in the afternoon of March 12, 2011, Unit 2 during the period from the late night of March 14 to the morning of March 15, 2011. These results corresponded to those assumed in our previous source term estimation studies. Furthermore, new findings suggested that the major source reactors from the evening of March 15, 2011 were Units 2 and 3 and that the dominant source reactor on March 20, 2011 temporally changed from Unit 3 to Unit 2.

Utilization of (134)Cs/(137)Cs in the environment to identify the reactor units that caused atmospheric releases during the Fukushima Daiichi accident.

PubMed

Chino, Masamichi; Terada, Hiroaki; Nagai, Haruyasu; Katata, Genki; Mikami, Satoshi; Torii, Tatsuo; Saito, Kimiaki; Nishizawa, Yukiyasu

2016-08-22

The Fukushima Daiichi nuclear power reactor units that generated large amounts of airborne discharges during the period of March 12-21, 2011 were identified individually by analyzing the combination of measured (134)Cs/(137)Cs depositions on ground surfaces and atmospheric transport and deposition simulations. Because the values of (134)Cs/(137)Cs are different in reactor units owing to fuel burnup differences, the (134)Cs/(137)Cs ratio measured in the environment was used to determine which reactor unit ultimately contaminated a specific area. Atmospheric dispersion model simulations were used for predicting specific areas contaminated by each dominant release. Finally, by comparing the results from both sources, the specific reactor units that yielded the most dominant atmospheric release quantities could be determined. The major source reactor units were Unit 1 in the afternoon of March 12, 2011, Unit 2 during the period from the late night of March 14 to the morning of March 15, 2011. These results corresponded to those assumed in our previous source term estimation studies. Furthermore, new findings suggested that the major source reactors from the evening of March 15, 2011 were Units 2 and 3 and that the dominant source reactor on March 20, 2011 temporally changed from Unit 3 to Unit 2.

Silver nanoparticles (AgNPs) as a contrast agent for imaging of animal tissue using swept-source optical coherence tomography (SSOCT)

NASA Astrophysics Data System (ADS)

Mondal, Indranil; Raj, Shipra; Roy, Poulomi; Poddar, Raju

2018-01-01

We present noninvasive three-dimensional depth-resolved imaging of animal tissue with a swept-source optical coherence tomography system at 1064 nm center wavelength and silver nanoparticles (AgNPs) as a potential contrast agent. A swept-source laser light source is used to enable an imaging rate of 100 kHz (100 000 A-scans s-1). Swept-source optical coherence tomography is a new variant of the optical coherence tomography (OCT) technique, offering unique advantages in terms of sensitivity, reduction of motion artifacts, etc. To enhance the contrast of an OCT image, AgNPs are utilized as an exogeneous contrast agent. AgNPs are synthesized using a modified Tollens method and characterization is done by UV-vis spectroscopy, dynamic light scattering, scanning electron microscopy and energy dispersive x-ray spectroscopy. In vitro imaging of chicken breast tissue, with and without the application of AgNPs, is performed. The effect of AgNPs is studied with different exposure times. A mathematical model is also built to calculate changes in the local scattering coefficient of tissue from OCT images. A quantitative estimation of scattering coefficient and contrast is performed for tissues with and without application of AgNPs. Significant improvement in contrast and increase in scattering coefficient with time is observed.

Utilization of 134Cs/137Cs in the environment to identify the reactor units that caused atmospheric releases during the Fukushima Daiichi accident

PubMed Central

Chino, Masamichi; Terada, Hiroaki; Nagai, Haruyasu; Katata, Genki; Mikami, Satoshi; Torii, Tatsuo; Saito, Kimiaki; Nishizawa, Yukiyasu

2016-01-01

The Fukushima Daiichi nuclear power reactor units that generated large amounts of airborne discharges during the period of March 12–21, 2011 were identified individually by analyzing the combination of measured 134Cs/137Cs depositions on ground surfaces and atmospheric transport and deposition simulations. Because the values of 134Cs/137Cs are different in reactor units owing to fuel burnup differences, the 134Cs/137Cs ratio measured in the environment was used to determine which reactor unit ultimately contaminated a specific area. Atmospheric dispersion model simulations were used for predicting specific areas contaminated by each dominant release. Finally, by comparing the results from both sources, the specific reactor units that yielded the most dominant atmospheric release quantities could be determined. The major source reactor units were Unit 1 in the afternoon of March 12, 2011, Unit 2 during the period from the late night of March 14 to the morning of March 15, 2011. These results corresponded to those assumed in our previous source term estimation studies. Furthermore, new findings suggested that the major source reactors from the evening of March 15, 2011 were Units 2 and 3 and that the dominant source reactor on March 20, 2011 temporally changed from Unit 3 to Unit 2. PMID:27546490

Gyrotactic swimmer dispersion in pipe flow: testing the theory

NASA Astrophysics Data System (ADS)

Croze, Ottavio A.; Bearon, Rachel N.; Bees, Martin A.

2017-04-01

Suspensions of microswimmers are a rich source of fascinating new fluid mechanics. Recently we predicted the active pipe flow dispersion of gyrotactic microalgae, whose orientation is biased by gravity and flow shear. Analytical theory predicts that these active swimmers disperse in a markedly distinct manner from passive tracers (Taylor dispersion). Dispersing swimmers display nonzero drift and effective diffusivity that is non-monotonic with P$\\'e$clet number. Such predictions agree with numerical simulations, but hitherto have not been tested experimentally. Here, to facilitate comparison, we obtain new solutions of the axial dispersion theory accounting both for swimmer negative buoyancy and a local nonlinear response of swimmers to shear, provided by two alternative microscopic stochastic descriptions. We obtain new predictions for suspensions of the model swimming alga $\\it Dunaliella\\,salina$, whose motility and buoyant mass we parametrise using tracking video microscopy. We then present a new experimental method to measure gyrotactic dispersion using fluorescently stained $\\it D. salina$ and provide a preliminary comparison with predictions of a nonzero drift above the mean flow for each microscopic stochastic description. Finally, we propose further experiments for a full experimental characterisation of gyrotactic dispersion measures and discuss implications of our results for algal dispersion in industrial photobioreactors.

Methodologies for evaluating performance and assessing uncertainty of atmospheric dispersion models

NASA Astrophysics Data System (ADS)

Chang, Joseph C.

This thesis describes methodologies to evaluate the performance and to assess the uncertainty of atmospheric dispersion models, tools that predict the fate of gases and aerosols upon their release into the atmosphere. Because of the large economic and public-health impacts often associated with the use of the dispersion model results, these models should be properly evaluated, and their uncertainty should be properly accounted for and understood. The CALPUFF, HPAC, and VLSTRACK dispersion modeling systems were applied to the Dipole Pride (DP26) field data (˜20 km in scale), in order to demonstrate the evaluation and uncertainty assessment methodologies. Dispersion model performance was found to be strongly dependent on the wind models used to generate gridded wind fields from observed station data. This is because, despite the fact that the test site was a flat area, the observed surface wind fields still showed considerable spatial variability, partly because of the surrounding mountains. It was found that the two components were comparable for the DP26 field data, with variability more important than uncertainty closer to the source, and less important farther away from the source. Therefore, reducing data errors for input meteorology may not necessarily increase model accuracy due to random turbulence. DP26 was a research-grade field experiment, where the source, meteorological, and concentration data were all well-measured. Another typical application of dispersion modeling is a forensic study where the data are usually quite scarce. An example would be the modeling of the alleged releases of chemical warfare agents during the 1991 Persian Gulf War, where the source data had to rely on intelligence reports, and where Iraq had stopped reporting weather data to the World Meteorological Organization since the 1981 Iran-Iraq-war. Therefore the meteorological fields inside Iraq must be estimated by models such as prognostic mesoscale meteorological models, based on observational data from areas outside of Iraq, and using the global fields simulated by the global meteorological models as the initial and boundary conditions for the mesoscale models. It was found that while comparing model predictions to observations in areas outside of Iraq, the predicted surface wind directions had errors between 30 to 90 deg, but the inter-model differences (or uncertainties) in the predicted surface wind directions inside Iraq, where there were no onsite data, were fairly constant at about 70 deg. (Abstract shortened by UMI.)

On inter-tidal transport equation

USGS Publications Warehouse

Cheng, Ralph T.; Feng, Shizuo; Pangen, Xi

1989-01-01

The transports of solutes, sediments, nutrients, and other tracers are fundamental to the interactive physical, chemical, and biological processes in estuaries. The characteristic time scales for most estuarine biological and chemical processes are on the order of several tidal cycles or longer. To address the long-term transport mechanism meaningfully, the formulation of an inter-tidal conservation equation is the main subject of this paper. The commonly used inter-tidal conservation equation takes the form of a convection-dispersion equation in which the convection is represented by the Eulerian residual current, and the dispersion terms are due to the introduction of a Fickian hypothesis, unfortunately, the physical significance of this equation is not clear, and the introduction of a Fickian hypothesis is at best an ad hoc approximation. Some recent research results on the Lagrangian residual current suggest that the long-term transport problem is more closely related to the Lagrangian residual current than to the Eulerian residual current. With the aid of additional insight of residual current, the inter-tidal transport equation has been reformulated in this paper using a small perturbation method for a weakly nonlinear tidal system. When tidal flows can be represented by an M2 system, the new intertidal transport equation also takes the form of a convective-dispersion equation without the introduction of a Fickian hypothesis. The convective velocity turns out to be the first order Lagrangian residual current (the sum of the Eulerian residual current and the Stokes’ drift), and the correlation terms take the form of convection with the Stokes’ drift as the convective velocity. The remaining dispersion terms are perturbations of lower order solution to higher order solutions due to shear effect and turbulent mixing.

Automatized near-real-time short-term Probabilistic Volcanic Hazard Assessment of tephra dispersion before and during eruptions: BET_VHst for Mt. Etna

NASA Astrophysics Data System (ADS)

Selva, Jacopo; Scollo, Simona; Costa, Antonio; Brancato, Alfonso; Prestifilippo, Michele

2015-04-01

Tephra dispersal, even in small amounts, may heavily affect public health and critical infrastructures, such as airports, train and road networks, and electric power supply systems. Probabilistic Volcanic Hazard Assessment (PVHA) represents the most complete scientific contribution for planning rational strategies aimed at managing and mitigating the risk posed by activity during volcanic crises and during eruptions. Short-term PVHA (over time intervals in the order of hours to few days) must account for rapidly changing information coming from the monitoring system, as well as, updated wind forecast, and they must be accomplished in near-real-time. In addition, while during unrest the primary goal is to forecast potential eruptions, during eruptions it is also fundamental to correctly account for the real-time status of the eruption and of tephra dispersal, as well as its potential evolution in the short-term. Here, we present a preliminary application of BET_VHst model (Selva et al. 2014) for Mt. Etna. The model has its roots into present state deterministic procedure, and it deals with the large uncertainty that such procedures typically ignore, like uncertainty on the potential position of the vent and eruptive size, on the possible evolution of volcanological input during ongoing eruptions, as well as, on wind field. Uncertainty is treated by making use of Bayesian inference, alternative modeling procedures for tephra dispersal, and statistical mixing of long- and short-term analyses. References Selva J., Costa A., Sandri L., Macedonio G., Marzocchi W. (2014) Probabilistic short-term volcanic hazard in phases of unrest: a case study for tephra fallout, J. Geophys. Res., 119, doi: 10.1002/2014JB011252

Dispersion of nano-silicon carbide (SiC) powder in aqueous suspensions

NASA Astrophysics Data System (ADS)

Singh, Bimal P.; Jena, Jayadev; Besra, Laxmidhar; Bhattacharjee, Sarama

2007-10-01

The dispersion characteristics of nanosize silicon carbide (SiC) suspension were investigated in terms of surface charge, particle size, rheological measurement and adsorption study. Ammonium polycarboxylate has been used as dispersant to stabilize the suspension. It was found that the isoelectric point (iep) of SiC powder was pHiep (4.9). The surface charge of powder changed significantly in presence of the ammonium polycarboxylate dispersant and iep shifted significantly towards lower acidic pH (3.6). The shift in iep has been quantified in terms of Δ G 0 SP, the specific free energy of adsorption between the surface sites and the adsorbing polyelectrolyte (APC). The values of Δ G 0 SP (-10.85 RT unit) estimated by the electro kinetic data compare well with those obtained from adsorption isotherms (-9.521 RT unit). The experimentally determined optimum concentration of dispersant required for maximizing the dispersion was found to be 2.4 mg/g of SiC (corresponding to an adsorbed amount of 1.10 mg/g), at pH 7.5. This is much below the full monolayer coverage (corresponding to adsorbed amount of 1.75 mg/g) of the particles surface by the dispersant. The surface charge quantity, rheological, pH, electro kinetic and adsorption isotherm results were used to explain and correlate the stability of the nanosize silicon carbide in aqueous media. At pH 7.5, where both SiC surface and APC are negatively charged, the adsorption of APC was low because of limited availability of favourable adsorption sites. In addition, the brush-like configuration of the adsorbed polymer prevented close approach of any additional dispersant; hence stabilization of the slurry happens at a comparatively lower concentration than the monolayer coverage.

Sources, dispersal, and fate of fine sediment supplied to coastal California

USGS Publications Warehouse

Farnsworth, Katherine L.; Warrick, Jonathan A.

2007-01-01

We have investigated the sources, dispersal, and fate of fine sediment supplied to California coastal waters in a partnership between the U.S. Geological Survey (USGS) and the California Sediment Management Workgroup (CSMW). The purpose of this study was to document the rates and characteristics of these processes so that the State can better manage its coastal resources, including sediment. In this study, we made the following observations: - Rivers dominate the supply of fine sediment to the California coastal waters, with an average annual flux of 34 megatonnes (Mt). - Cliff and bluff erosion in central and southern California is a source of fine sediment, with a delivery rate of approximately 10 percent of river loads. In the southern most part of the State, however, where river-sediment loads are low, cliff and bluff erosion represent approximately 40 percent of the total fine-sediment flux. - Temporal variation in the sources of fine sediment is high. River floods and bluff erosion are episodic and dominated by winter storms, which supply most sediment flux to the coast. The magnitude of winter storms is generally related to the El Niño-Southern Oscillation (ENSO) and Pacific Decadal Oscillation (PDO) climate cycles. - The three rivers that dominate fine-sediment flux to the California coast are the Eel, Salinas, and Santa Clara Rivers. Because the sediment delivery from these and all other California coastal watersheds is episodic, individual rivers discharge most of their annual loads over the course of only a few days per year. - Spatial variation in river-sediment discharge is high and generally related to such watershed characteristics as geology, precipitation, and drainage area. For example, the Transverse Range of southern California represents only 9 percent of the watershed-drainage area but 18 percent of the fine-sediment flux, a function of the young sedimentary bedrock and active tectonics of this region. The urban rivers of southern California were observed to discharge sediment at rates consistent with those of the surrounding Transverse Range rivers, which share the same geologic setting. - Direct observations of fine-sediment dispersal have been limited to the river-mouth settings of the Eel and Santa Clara Rivers, where sediment has been observed to settle quickly from buoyant plumes and be transported along the seabed during periods of storm waves. - After heavy loading of fine sediment onto the continental shelf during river floods, there is increasing evidence that fluid-mud gravity flows occur within a layer 10 to 50 cm above the seabed and efficiently transport fine sediment offshore. - All along the California coast, the timing of river discharge and coastal winds and waves from storm events are strongly coherent; however, of large wave events with the potential for resuspending and transporting fine sediment occur during periods without significant rainfall and therefore no significant river discharge. - Although fine sediment dominates the midshelf mud belts offshore of California river mouths, these mud belts are not the dominant sink of fine sediment, much of which is deposited across the entire continental shelf, including the inner shelf, and offshelf into deeper water depths. - Accumulation rates of fine sediment, which can exceed several millimeters per year, are generally highest near river sources of sediment and along the inner shelf and midshelf. - Sediment-accumulation rates, as summarized from both long-term and recent investigations of continental-shelf geochronology, are generally consistent across California except in southern California, where recently the sediment-accumulation rate has been tenfold greater than the long-term rate, possibly as a result of increased river discharge, wastewater outfall inputs, or other anthropogenic sources. Thus, fine sediment is a natural and dynamic element of the California coastal system because of large, natural sediment sources and dynamic transport processes.

Landscape resistance to dispersal: Predicting long-term effects for a small and isolated wolf population in southwestern Manitoba, Canada

EPA Science Inventory

Landscape fragmentation affects wildlife population viability, in part through the effects it has on individual dispersal. Considerable fragmentation of native habitats and loss of forest cover has occurred in association with agricultural development over the past 50 years in o...

Prioritizing environmental justice and equality: diesel emissions in southern California.

PubMed

Marshall, Julian D; Swor, Kathryn R; Nguyen, Nam P

2014-04-01

Existing environmental policies aim to reduce emissions but lack standards for addressing environmental justice. Environmental justice research documents disparities in exposure to air pollution; however, little guidance currently exists on how to make improvements or on how specific emission-reduction scenarios would improve or deteriorate environmental justice conditions. Here, we quantify how emission reductions from specific sources would change various measures of environmental equality and justice. We evaluate potential emission reductions for fine diesel particulate matter (DPM) in Southern California for five sources: on-road mobile, off-road mobile, ships, trains, and stationary. Our approach employs state-of-the-science dispersion and exposure models. We compare four environmental goals: impact, efficiency, equality, and justice. Results indicate potential trade-offs among those goals. For example, reductions in train emissions produce the greatest improvements in terms of efficiency, equality, and justice, whereas off-road mobile source reductions can have the greatest total impact. Reductions in on-road emissions produce improvements in impact, equality, and justice, whereas emission reductions from ships would widen existing population inequalities. Results are similar for complex versus simplified exposure analyses. The approach employed here could usefully be applied elsewhere to evaluate opportunities for improving environmental equality and justice in other locations.

Dispersion relations for η '→ η π π

NASA Astrophysics Data System (ADS)

Isken, Tobias; Kubis, Bastian; Schneider, Sebastian P.; Stoffer, Peter

2017-07-01

We present a dispersive analysis of the decay amplitude for η '→ η π π that is based on the fundamental principles of analyticity and unitarity. In this framework, final-state interactions are fully taken into account. Our dispersive representation relies only on input for the {π π } and {π }η scattering phase shifts. Isospin symmetry allows us to describe both the charged and neutral decay channel in terms of the same function. The dispersion relation contains subtraction constants that cannot be fixed by unitarity. We determine these parameters by a fit to Dalitz-plot data from the VES and BES-III experiments. We study the prediction of a low-energy theorem and compare the dispersive fit to variants of chiral perturbation theory.

Biomonitoring of airborne particulate matter emitted from a cement plant and comparison with dispersion modelling results

NASA Astrophysics Data System (ADS)

Abril, Gabriela A.; Wannaz, Eduardo D.; Mateos, Ana C.; Pignata, María L.

2014-01-01

The influence of a cement plant that incinerates industrial waste on the air quality of a region in the province of Córdoba, Argentina, was assessed by means of biomonitoring studies (effects of immission) and atmospheric dispersion (effects of emission) of PM10 with the application of the ISC3 model (Industrial Source Complex) developed by the USEPA (Environmental Protection Agency). For the biomonitoring studies, samples from the epiphyte plant Tillandsia capillaris Ruíz & Pav. f. capillaris were transplanted to the vicinities of the cement plant in order to determine the physiological damage and heavy metal accumulation (Ca, Mn, Fe, Co, Ni, Cu, Zn, Cd and Pb). For the application of the ISC3 model, point and area sources from the cement plant were considered to obtain average PM10 concentration results from the biomonitoring exposure period. This model permitted it to be determined that the emissions from the cement plant (point and area sources) were confined to the vicinities, without significant dispersion in the study area. This was also observed in the biomonitoring study, which identified Ca, Cd and Pb, pH and electric conductivity (EC) as biomarkers of this cement plant. Vehicular traffic emissions and soil re-suspension could be observed in the biomonitors, giving a more complete scenario. In this study, biomonitoring studies along with the application of atmospheric dispersion models, allowed the atmospheric pollution to be assessed in more detail.

A comparison of dispersing media for various engineered carbon nanoparticles.

PubMed

Buford, Mary C; Hamilton, Raymond F; Holian, Andrij

2007-07-27

With the increased manufacture and use of carbon nanoparticles (CNP) there has been increasing concern about the potential toxicity of fugitive CNP in the workplace and ambient environment. To address this matter a number of investigators have conducted in vitro and in vivo toxicity assessments. However, a variety of different approaches for suspension of these particles (culture media, Tween 80, dimethyl sulfoxide, phosphate-buffered saline, fetal calf serum, and others), and different sources of materials have generated potentially conflicting outcomes. The quality of the dispersion of nanoparticles is very dependent on the medium used to suspend them, and this then will most likely affect the biological outcomes. In this work, the distributions of different CNP (sources and types) have been characterized in various media. Furthermore, the outcome of instilling the different agglomerates, or size distributions, was examined in mouse lungs after one and seven days. Our results demonstrated that CNP suspended in serum produced particle suspensions with the fewest large agglomerates, and the most uniform distribution in mouse lungs. In addition, no apparent clearance of instilled CNP took place from lungs even after seven days. This work demonstrates that CNP agglomerates are present in all dispersing vehicles to some degree. The vehicle that contains some protein, lipid or protein/lipid component disperses the CNP best, producing fewer large CNP agglomerates. In contrast, vehicles absent of lipid and protein produce the largest CNP agglomerates. The source of the CNP is also a factor in the degree of particle agglomeration within the same vehicle.

Modeling tidal exchange and dispersion in Boston Harbor

USGS Publications Warehouse

Signell, Richard P.; Butman, Bradford

1992-01-01

Tidal dispersion and the horizontal exchange of water between Boston Harbor and the surrounding ocean are examined with a high-resolution (200 m) depth-averaged numerical model. The strongly varying bathymetry and coastline geometry of the harbor generate complex spatial patterns in the modeled tidal currents which are verified by shipboard acoustic Doppler surveys. Lagrangian exchange experiments demonstrate that tidal currents rapidly exchange and mix material near the inlets of the harbor due to asymmetry in the ebb/flood response. This tidal mixing zone extends roughly a tidal excursion from the inlets and plays an important role in the overall flushing of the harbor. Because the tides can only efficiently mix material in this limited region, however, harbor flushing must be considered a two step process: rapid exchange in the tidal mixing zone, followed by flushing of the tidal mixing zone by nontidal residual currents. Estimates of embayment flushing based on tidal calculations alone therefore can significantly overestimate the flushing time that would be expected under typical environmental conditions. Particle-release simulations from point sources also demonstrate that while the tides efficiently exchange material in the vicinity of the inlets, the exact nature of dispersion from point sources is extremely sensitive to the timing and location of the release, and the distribution of particles is streaky and patchlike. This suggests that high-resolution modeling of dispersion from point sources in these regions must be performed explicitly and cannot be parameterized as a plume with Gaussian-spreading in a larger scale flow field.

Controlling dispersion characteristics of terahertz metasurface.

PubMed

Qu, Shi-Wei; Wu, Wei-Wei; Chen, Bao-Jie; Yi, Huan; Bai, Xue; Ng, Kung Bo; Chan, Chi Hou

2015-03-23

Terahertz (THz) metasurfaces have been explored recently due to their properties such as low material loss and ease of fabrication compared to three-dimensional (3D) metamaterials. Although the dispersion properties of the reflection/transmission-type THz metasurface were observed in some published literature, the method to control them at will has been scarcely reported to the best of our knowledge. In this context, flexible dispersion control of the THz metasurface will lead to great opportunities toward unprecedented THz devices. As an example, a THz metasurface with controllable dispersion characteristics has been successfully demonstrated in this article, and the incident waves at different frequencies from a source in front of the metasurface can be projected into different desired anomalous angular positions. Furthermore, this work provides a potential approach to other kinds of novel THz devices that need controllable metasurface dispersion properties.

Controlling Dispersion Characteristics of Terahertz Metasurface

PubMed Central

Qu, Shi-Wei; Wu, Wei-Wei; Chen, Bao-Jie; Yi, Huan; Bai, Xue; Ng, Kung Bo; Chan, Chi Hou

2015-01-01

Terahertz (THz) metasurfaces have been explored recently due to their properties such as low material loss and ease of fabrication compared to three-dimensional (3D) metamaterials. Although the dispersion properties of the reflection/transmission-type THz metasurface were observed in some published literature, the method to control them at will has been scarcely reported to the best of our knowledge. In this context, flexible dispersion control of the THz metasurface will lead to great opportunities toward unprecedented THz devices. As an example, a THz metasurface with controllable dispersion characteristics has been successfully demonstrated in this article, and the incident waves at different frequencies from a source in front of the metasurface can be projected into different desired anomalous angular positions. Furthermore, this work provides a potential approach to other kinds of novel THz devices that need controllable metasurface dispersion properties. PMID:25797336

Solid-state radioluminescent zeolite-containing composition and light sources

DOEpatents

Clough, Roger L.; Gill, John T.; Hawkins, Daniel B.; Renschler, Clifford L.; Shepodd, Timothy J.; Smith, Henry M.

1992-01-01

A new type of RL light source consisting of a zeolite crystalline material, the intralattice spaces of which a tritiated compound and a luminophore are sorbed, and which material is optionally further dispersed in a refractive index-matched polymer matrix.

Molybdenum enhanced low-temperature deposition of crystalline silicon nitride

DOEpatents

Lowden, R.A.

1994-04-05

A process for chemical vapor deposition of crystalline silicon nitride is described which comprises the steps of: introducing a mixture of a silicon source, a molybdenum source, a nitrogen source, and a hydrogen source into a vessel containing a suitable substrate; and thermally decomposing the mixture to deposit onto the substrate a coating comprising crystalline silicon nitride containing a dispersion of molybdenum silicide. 5 figures.

Modeling the combined influence of host dispersal and waterborne fate and transport on pathogen spread in complex landscapes

PubMed Central

Lu, Ding; McDowell, Julia Z.; Davis, George M.; Spear, Robert C.; Remais, Justin V.

2012-01-01

Environmental models, often applied to questions on the fate and transport of chemical hazards, have recently become important in tracing certain environmental pathogens to their upstream sources of contamination. These tools, such as first order decay models applied to contaminants in surface waters, offer promise for quantifying the fate and transport of pathogens with multiple environmental stages and/or multiple hosts, in addition to those pathogens whose environmental stages are entirely waterborne. Here we consider the fate and transport capabilities of the human schistosome Schistosoma japonicum, which exhibits two waterborne stages and is carried by an amphibious intermediate snail host. We present experimentally-derived dispersal estimates for the intermediate snail host and fate and transport estimates for the passive downstream diffusion of cercariae, the waterborne, human-infective parasite stage. Using a one dimensional advective transport model exhibiting first-order decay, we simulate the added spatial reach and relative increase in cercarial concentrations that dispersing snail hosts contribute to downstream sites. Simulation results suggest that snail dispersal can substantially increase the concentrations of cercariae reaching downstream locations, relative to no snail dispersal, effectively putting otherwise isolated downstream sites at increased risk of exposure to cercariae from upstream sources. The models developed here can be applied to other infectious diseases with multiple life-stages and hosts, and have important implications for targeted ecological control of disease spread. PMID:23162675

Comparison of clast and matrix dispersal in till: Charlo-Atholville area, north-central New Brunswick

USGS Publications Warehouse

Dickson, M.L.; Broster, B.E.; Parkhill, M.A.

2004-01-01

Striations and dispersal patterns for till clasts and matrix geochemistry are used to define flow directions of glacial transport across an area of about 800km2 in the Charlo-Atholville area of north-central New Brunswick. A total of 170 clast samples and 328 till matrix samples collected for geochemical analysis across the region, were analyzed for a total of 39 elements. Major lithologic contacts used here to delineate till clast provenance were based on recent bedrock mapping. Eleven known mineral occurrences and a gossan are used to define point source targets for matrix geochemical dispersal trains and to estimate probable distance and direction of transport from unknown sources. Clast trains are traceable for distances of approximately 10 km, whereas till geochemical dispersal patterns are commonly lost within 5 km of transport. Most dispersal patterns reflect more than a single direction of glacial transport. These data indicate that a single till sheet, 1-4 m thick, was deposited as the dominant ice-flow direction fluctuated between southeastward, eastward, and northward over the study area. Directions of early flow represent changes in ice sheet dominance, first from the northwest and then from the west. Locally, eastward and northward flow represent the maximum erosive phases. The last directions of flow are likely due to late glacial ice sheet drawdown towards the valley outlet at Baie des Chaleurs.

Extracting and compensating dispersion mismatch in ultrahigh-resolution Fourier domain OCT imaging of the retina

PubMed Central

Choi, WooJhon; Baumann, Bernhard; Swanson, Eric A.; Fujimoto, James G.

2012-01-01

We present a numerical approach to extract the dispersion mismatch in ultrahigh-resolution Fourier domain optical coherence tomography (OCT) imaging of the retina. The method draws upon an analogy with a Shack-Hartmann wavefront sensor. By exploiting mathematical similarities between the expressions for aberration in optical imaging and dispersion mismatch in spectral / Fourier domain OCT, Shack-Hartmann principles can be extended from the two-dimensional paraxial wavevector space (or the x-y plane in the spatial domain) to the one-dimensional wavenumber space (or the z-axis in the spatial domain). For OCT imaging of the retina, different retinal layers, such as the retinal nerve fiber layer (RNFL), the photoreceptor inner and outer segment junction (IS/OS), or all the retinal layers near the retinal pigment epithelium (RPE) can be used as point source beacons in the axial direction, analogous to point source beacons used in conventional two-dimensional Shack-Hartman wavefront sensors for aberration characterization. Subtleties regarding speckle phenomena in optical imaging, which affect the Shack-Hartmann wavefront sensor used in adaptive optics, also occur analogously in this application. Using this approach and carefully suppressing speckle, the dispersion mismatch in spectral / Fourier domain OCT retinal imaging can be successfully extracted numerically and used for numerical dispersion compensation to generate sharper, ultrahigh-resolution OCT images. PMID:23187353

Depth-enhanced three-dimensional-two-dimensional convertible display based on modified integral imaging.

PubMed

Park, Jae-Hyeung; Kim, Hak-Rin; Kim, Yunhee; Kim, Joohwan; Hong, Jisoo; Lee, Sin-Doo; Lee, Byoungho

2004-12-01

A depth-enhanced three-dimensional-two-dimensional convertible display that uses a polymer-dispersed liquid crystal based on the principle of integral imaging is proposed. In the proposed method, a lens array is located behind a transmission-type display panel to form an array of point-light sources, and a polymer-dispersed liquid crystal is electrically controlled to pass or to scatter light coming from these point-light sources. Therefore, three-dimensional-two-dimensional conversion is accomplished electrically without any mechanical movement. Moreover, the nonimaging structure of the proposed method increases the expressible depth range considerably. We explain the method of operation and present experimental results.

Small-scale seismic inversion using surface waves extracted from noise cross correlation.

PubMed

Gouédard, Pierre; Roux, Philippe; Campillo, Michel

2008-03-01

Green's functions can be retrieved between receivers from the correlation of ambient seismic noise or with an appropriate set of randomly distributed sources. This principle is demonstrated in small-scale geophysics using noise sources generated by human steps during a 10-min walk in the alignment of a 14-m-long accelerometer line array. The time-domain correlation of the records yields two surface wave modes extracted from the Green's function between each pair of accelerometers. A frequency-wave-number Fourier analysis yields each mode contribution and their dispersion curve. These dispersion curves are then inverted to provide the one-dimensional shear velocity of the near surface.

Bright broadband coherent fiber sources emitting strongly blue-shifted resonant dispersive wave pulses

PubMed Central

Tu, Haohua; Lægsgaard, Jesper; Zhang, Rui; Tong, Shi; Liu, Yuan; Boppart, Stephen A.

2013-01-01

We predict and realize the targeted wavelength conversion from the 1550-nm band of a fs Er:fiber laser to an isolated band inside 370-850 nm, corresponding to a blue-shift of 700-1180 nm. The conversion utilizes resonant dispersive wave generation in widely available optical fibers with good efficiency (~7%). The converted band has a large pulse energy (~1 nJ), high spectral brightness (~1 mW/nm), and broad Gaussian-like spectrum compressible to clean transform-limited ~17 fs pulses. The corresponding coherent fiber sources open up portable applications of optical parametric oscillators and dual-output synchronized ultrafast lasers. PMID:24104233

Uncertainty Estimation Cheat Sheet for Probabilistic Risk Assessment

NASA Technical Reports Server (NTRS)

Britton, Paul T.; Al Hassan, Mohammad; Ring, Robert W.

2017-01-01

"Uncertainty analysis itself is uncertain, therefore, you cannot evaluate it exactly," Source Uncertain Quantitative results for aerospace engineering problems are influenced by many sources of uncertainty. Uncertainty analysis aims to make a technical contribution to decision-making through the quantification of uncertainties in the relevant variables as well as through the propagation of these uncertainties up to the result. Uncertainty can be thought of as a measure of the 'goodness' of a result and is typically represented as statistical dispersion. This paper will explain common measures of centrality and dispersion; and-with examples-will provide guidelines for how they may be estimated to ensure effective technical contributions to decision-making.

Lognormal Uncertainty Estimation for Failure Rates

NASA Technical Reports Server (NTRS)

Britton, Paul T.; Al Hassan, Mohammad; Ring, Robert W.

2017-01-01

"Uncertainty analysis itself is uncertain, therefore, you cannot evaluate it exactly," Source Uncertain. Quantitative results for aerospace engineering problems are influenced by many sources of uncertainty. Uncertainty analysis aims to make a technical contribution to decision-making through the quantification of uncertainties in the relevant variables as well as through the propagation of these uncertainties up to the result. Uncertainty can be thought of as a measure of the 'goodness' of a result and is typically represented as statistical dispersion. This presentation will explain common measures of centrality and dispersion; and-with examples-will provide guidelines for how they may be estimated to ensure effective technical contributions to decision-making.

A repeating fast radio burst

NASA Astrophysics Data System (ADS)

Spitler, L. G.; Scholz, P.; Hessels, J. W. T.; Bogdanov, S.; Brazier, A.; Camilo, F.; Chatterjee, S.; Cordes, J. M.; Crawford, F.; Deneva, J.; Ferdman, R. D.; Freire, P. C. C.; Kaspi, V. M.; Lazarus, P.; Lynch, R.; Madsen, E. C.; McLaughlin, M. A.; Patel, C.; Ransom, S. M.; Seymour, A.; Stairs, I. H.; Stappers, B. W.; van Leeuwen, J.; Zhu, W. W.

2016-03-01

Fast radio bursts are millisecond-duration astronomical radio pulses of unknown physical origin that appear to come from extragalactic distances. Previous follow-up observations have failed to find additional bursts at the same dispersion measure (that is, the integrated column density of free electrons between source and telescope) and sky position as the original detections. The apparent non-repeating nature of these bursts has led to the suggestion that they originate in cataclysmic events. Here we report observations of ten additional bursts from the direction of the fast radio burst FRB 121102. These bursts have dispersion measures and sky positions consistent with the original burst. This unambiguously identifies FRB 121102 as repeating and demonstrates that its source survives the energetic events that cause the bursts. Additionally, the bursts from FRB 121102 show a wide range of spectral shapes that appear to be predominantly intrinsic to the source and which vary on timescales of minutes or less. Although there may be multiple physical origins for the population of fast radio bursts, these repeat bursts with high dispersion measure and variable spectra specifically seen from the direction of FRB 121102 support an origin in a young, highly magnetized, extragalactic neutron star.

A repeating fast radio burst.

PubMed

Spitler, L G; Scholz, P; Hessels, J W T; Bogdanov, S; Brazier, A; Camilo, F; Chatterjee, S; Cordes, J M; Crawford, F; Deneva, J; Ferdman, R D; Freire, P C C; Kaspi, V M; Lazarus, P; Lynch, R; Madsen, E C; McLaughlin, M A; Patel, C; Ransom, S M; Seymour, A; Stairs, I H; Stappers, B W; van Leeuwen, J; Zhu, W W

2016-03-10

Fast radio bursts are millisecond-duration astronomical radio pulses of unknown physical origin that appear to come from extragalactic distances. Previous follow-up observations have failed to find additional bursts at the same dispersion measure (that is, the integrated column density of free electrons between source and telescope) and sky position as the original detections. The apparent non-repeating nature of these bursts has led to the suggestion that they originate in cataclysmic events. Here we report observations of ten additional bursts from the direction of the fast radio burst FRB 121102. These bursts have dispersion measures and sky positions consistent with the original burst. This unambiguously identifies FRB 121102 as repeating and demonstrates that its source survives the energetic events that cause the bursts. Additionally, the bursts from FRB 121102 show a wide range of spectral shapes that appear to be predominantly intrinsic to the source and which vary on timescales of minutes or less. Although there may be multiple physical origins for the population of fast radio bursts, these repeat bursts with high dispersion measure and variable spectra specifically seen from the direction of FRB 121102 support an origin in a young, highly magnetized, extragalactic neutron star.

Enhanced global Radionuclide Source Attribution for the Nuclear-Test-Ban Verification by means of the Adjoint Ensemble Dispersion Modeling Technique applied at the IDC/CTBTO.

NASA Astrophysics Data System (ADS)

Becker, A.; Wotawa, G.; de Geer, L.

2006-05-01

The Provisional Technical Secretariat (PTS) of the CTBTO Preparatory Commission maintains and permanently updates a source-receptor matrix (SRM) describing the global monitoring capability of a highly sensitive 80 stations radionuclide (RN) network in order to verify states signatories' compliance of the comprehensive nuclear-test-ban treaty (CTBT). This is done by means of receptor-oriented Lagrangian particle dispersion modeling (LPDM) to help determine the region from which suspicious radionuclides may originate. In doing so the LPDM FLEXPART5.1 is integrated backward in time based on global analysis wind fields yielding global source-receptor sensitivity (SRS) fields stored in three-hour frequency and at 1º horizontal resolution. A database of these SRS fields substantially helps in improving the interpretation of the RN samples measurements and categorizations because it enables the testing of source-hypothesis's later on in a pure post-processing (SRM inversion) step being feasible on hardware with specifications comparable to currently sold PC's or Notebooks and at any place (decentralized), provided access to the SRS fields is warranted. Within the CTBT environment it is important to quickly achieve decision-makers confidence in the SRM based backtracking products issued by the PTS in the case of the occurrence of treaty relevant radionuclides. Therefore the PTS has set up a highly automated response system together with the Regional Specialized Meteorological Centers of the World Meteorological Organization in the field of dispersion modeling who committed themselves to provide the PTS with the same standard SRS fields as calculated by their systems for CTBT relevant cases. This system was twice utilized in 2005 in order to perform adjoint ensemble dispersion modeling (EDM) and demonstrated the potential of EDM based backtracking to improve the accuracy of the source location related to singular nuclear events thus serving the backward analogue to the findings of the ensemble dispersion modeling (EDM) technique No. 5 efforts performed by Galmarini et al, 2004 (Atmos. Env. 38, 4607-4617). As the scope of the adjoint EDM methodology is not limited to CTBT verification but can be applied to any kind of nuclear event monitoring and location it bears the potential to improve the design of manifold emergency response systems towards preparedness concepts as needed for mitigation of disasters (like Chernobyl) and pre-emptive estimation of pollution hazards.

Contrasting plant height can improve the control of rain-borne diseases in wheat cultivar mixture: modelling splash dispersal in 3-D canopies.

PubMed

Vidal, T; Gigot, C; de Vallavieille-Pope, C; Huber, L; Saint-Jean, S

2018-06-08

Growing cultivars differing by their disease resistance level together (cultivar mixtures) can reduce the propagation of diseases. Although architectural characteristics of cultivars are little considered in mixture design, they could have an effect on disease, in particular through spore dispersal by rain splash, which occurs over short distances. The objective of this work was to assess the impact of plant height of wheat cultivars in mixtures on splash dispersal of Zymoseptoria tritici, which causes septoria tritici leaf blotch. We used a modelling approach involving an explicit description of canopy architecture and splash dispersal processes. The dispersal model computed raindrop interception by a virtual canopy as well as the production, transport and interception of splash droplets carrying inoculum. We designed 3-D virtual canopies composed of susceptible and resistant plants, according to field measurements at the flowering stage. In numerical experiments, we tested different heights of virtual cultivars making up binary mixtures to assess the influence of this architectural trait on dispersal patterns of spore-carrying droplets. Inoculum interception decreased exponentially with the height relative to the main inoculum source (lower diseased leaves of susceptible plants), and little inoculum was intercepted further than 40 cm above the inoculum source. Consequently, tall plants intercepted less inoculum than smaller ones. Plants with twice the standard height intercepted 33 % less inoculum than standard height plants. In cases when the height of suscpeptible plants was doubled, inoculum interception by resistant leaves was 40 % higher. This physical barrier to spore-carrying droplet trajectories reduced inoculum interception by tall susceptible plants and was modulated by plant height differences between cultivars of a binary mixture. These results suggest that mixture effects on spore dispersal could be modulated by an adequate choice of architectural characteristics of cultivars. In particular, even small differences in plant height could reduce spore dispersal.

Dispersal of emerald ash borer at outlier sites: three case studies

Treesearch

Deborah G. McCullough; Nathan W. Siegert; Therese M. Poland; David L. Cappaert; Ivich Fraser; David Williams

2005-01-01

We worked with cooperators from several state and federal agencies in 2003 and 2004 to assess dispersal of emerald ash borer (EAB), Agrilus planipennis Fairmaire, from known source points in three outlier sites. In February 2003, we felled and sampled more than 200 ash trees at an outlier site near Tipton, Michigan, where one generation of adult...

[Disperse endocrine system and APUD concept].

PubMed

Mil'to, I V; Sukhodolo, I V; Gereng, E A; Shamardina, L A

2011-01-01

This review describes the problems of disperse endocrine system and APUD-system morphology, summarizes some debatable issues of single endocrine cell biology. The data presented refer to the history of both systems discovery, morphological methods of their study, developmental sources, their structural organization and physiological roles of their cells. The significance of single endocrine cells in the regulation of the organism functions is discussed.

Joshua tree (Yucca brevifolia) seeds are dispersed by seed-caching rodents

USGS Publications Warehouse

Vander Wall, S.B.; Esque, T.; Haines, D.; Garnett, M.; Waitman, B.A.

2006-01-01

Joshua tree (Yucca brevifolia) is a distinctive and charismatic plant of the Mojave Desert. Although floral biology and seed production of Joshua tree and other yuccas are well understood, the fate of Joshua tree seeds has never been studied. We tested the hypothesis that Joshua tree seeds are dispersed by seed-caching rodents. We radioactively labelled Joshua tree seeds and followed their fates at five source plants in Potosi Wash, Clark County, Nevada, USA. Rodents made a mean of 30.6 caches, usually within 30 m of the base of source plants. Caches contained a mean of 5.2 seeds buried 3-30 nun deep. A variety of rodent species appears to have prepared the caches. Three of the 836 Joshua tree seeds (0.4%) cached germinated the following spring. Seed germination using rodent exclosures was nearly 15%. More than 82% of seeds in open plots were removed by granivores, and neither microsite nor supplemental water significantly affected germination. Joshua tree produces seeds in indehiscent pods or capsules, which rodents dismantle to harvest seeds. Because there is no other known means of seed dispersal, it is possible that the Joshua tree-rodent seed dispersal interaction is an obligate mutualism for the plant.

A wind tunnel study of gaseous tracer dispersion in the convective boundary layer capped by a temperature inversion

NASA Astrophysics Data System (ADS)

Fedorovich, E.; Thäter, J.

Results are presented from wind tunnel simulations of gaseous pollutant dispersion in the atmospheric convective boundary layer (CBL) capped by a temperature inversion. The experiments were performed in the thermally stratified wind tunnel of the University of Karlsruhe, Germany. In the tunnel, the case of horizontally evolving, sheared CBL is reproduced. This distinguishes the employed experimental setup from the preceding laboratory and numerical CBL dispersion studies. The diffusive and mixing properties of turbulence in the studied CBL case have been found to be essentially dependent on the stage of the CBL evolution. Effects of the point source elevation on the horizontal variability of the concentration field, and on the ground level concentration as function of distance from the source have been investigated. The applicability of bottom-up/top-down diffusion concept in the simulated CBL case has been evaluated. The influence of surface wind shear and capping inversion strength on the pollutant dispersion and turbulent exchange across the CBL top has been demonstrated. The imposed positive shear across the inversion has been identified as inhibitor of the CBL growth. Comparisons of concentration patterns from the wind tunnel with water tank data are presented.

Dispersion of Self-Propelled Rods Undergoing Fluctuation-Driven Flips

NASA Astrophysics Data System (ADS)

Takagi, Daisuke; Braunschweig, Adam B.; Zhang, Jun; Shelley, Michael J.

2013-01-01

Synthetic microswimmers may someday perform medical and technological tasks, but predicting their motion and dispersion is challenging. Here we show that chemically propelled rods tend to move on a surface along large circles but curiously show stochastic changes in the sign of the orbit curvature. By accounting for fluctuation-driven flipping of slightly curved rods, we obtain analytical predictions for the ensemble behavior in good agreement with our experiments. This shows that minor defects in swimmer shape can yield major long-term effects on macroscopic dispersion.

Accounting for the dispersion in the x ray properties of early-type galaxies

NASA Technical Reports Server (NTRS)

White, Raymond E., III; Sarazin, Craig L.

1990-01-01

The x ray luminosities of early-type galaxies are correlated with their optical (e.g., blue) luminosities (L sub X approx. L sub B exp 1.6), but the x ray luminosities exhibit considerable scatter for a given optical luminosity L sub B. This dispersion in x ray luminosity is much greater than the dispersion of other properties of early-type galaxies (for a given L sub B), such as luminosity scale-length, velocity dispersion, color, and metallicity. Here, researchers consider several possible sources for the dispersion in x ray luminosity. Some of the scatter in x ray luminosity may result from stellar population variations between galaxies with similar L sub B. Since the x ray emitting gas is from accumulated stellar mass loss, the L sub X dispersion may be due to variations in integrated stellar mass loss rates. Another possible cause of the L sub X dispersion may be variations in the amount of cool material in the galaxies; cool gas may act as an energy sink for the hot gas. Infrared emission may be used to trace such cool material, so researchers look for a correlation between the infrared emission and the x ray emission of early-type galaxies at fixed L sub B. Velocity dispersion variations between galaxies of similar L sub B may also contribute to the L sub X dispersion. The most likely a priori source of the dispersion in L sub X is probably the varying amount of ram-pressure stripping in a range of galaxy environments. The hot gaseous halos of early-type galaxies can be stripped in encounters with other galaxies or with ambient cluster gas if the intracluster gas is sufficiently dense. Researchers find that the most likely cause of dispersion in the x ray properties of early type galaxies is probably the ram-pressure stripping of gaseous halos from galaxies. For a sample of 81 early-type galaxies with x ray luminosities or upper limits derived from Einstein Observatory observations (CFT) researchers calculated the cumulative distribution of angular distances between the x ray sample members and bright galaxies from the Revised Shapley - Ames catalog. Collectively, galaxies with low x ray luminosities (for a given L sub B) tend to be in denser environments than galaxies with higher x ray luminosities.

An Overlap Syndrome of Pigment Dispersion and Pigmentary Glaucoma accompanied by Marfan Syndrome: Case Report with Literature Review.

PubMed

Chakravarti, Tutul; Spaeth, George

2013-01-01

'Overlap syndrome' describes the situation in which two or more 'independent' conditions are present, either one of which could cause a particular finding. This current presentation reports a case with bilateral pigment dispersion syndrome (PDS), advanced pigmentary glaucoma (PG), and the Marfan syndrome, with bilateral subluxation of the lenses, and large short-term and long-term fluctuations of intraocular pressure. It is interesting to consider whether the associated advanced glaucomatous nerve damage could be a manifestation of just the PDS, just the Marfan syndrome, or rather a combination of these two overlapping independent conditions. How to cite this article: Chakravarti T, George S. An Overlap Syndrome of Pigment Dispersion and Pigmentary Glaucoma accompanied by Marfan Syndrome: Case Report with Literature Review. J Current Glau Prac 2013;7(2):91-95.

Distribution function approach to redshift space distortions. Part IV: perturbation theory applied to dark matter

NASA Astrophysics Data System (ADS)

Vlah, Zvonimir; Seljak, Uroš; McDonald, Patrick; Okumura, Teppei; Baldauf, Tobias

2012-11-01

We develop a perturbative approach to redshift space distortions (RSD) using the phase space distribution function approach and apply it to the dark matter redshift space power spectrum and its moments. RSD can be written as a sum over density weighted velocity moments correlators, with the lowest order being density, momentum density and stress energy density. We use standard and extended perturbation theory (PT) to determine their auto and cross correlators, comparing them to N-body simulations. We show which of the terms can be modeled well with the standard PT and which need additional terms that include higher order corrections which cannot be modeled in PT. Most of these additional terms are related to the small scale velocity dispersion effects, the so called finger of god (FoG) effects, which affect some, but not all, of the terms in this expansion, and which can be approximately modeled using a simple physically motivated ansatz such as the halo model. We point out that there are several velocity dispersions that enter into the detailed RSD analysis with very different amplitudes, which can be approximately predicted by the halo model. In contrast to previous models our approach systematically includes all of the terms at a given order in PT and provides a physical interpretation for the small scale dispersion values. We investigate RSD power spectrum as a function of μ, the cosine of the angle between the Fourier mode and line of sight, focusing on the lowest order powers of μ and multipole moments which dominate the observable RSD power spectrum. Overall we find considerable success in modeling many, but not all, of the terms in this expansion. This is similar to the situation in real space, but predicting power spectrum in redshift space is more difficult because of the explicit influence of small scale dispersion type effects in RSD, which extend to very large scales.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vlah, Zvonimir; Seljak, Uroš; Baldauf, Tobias

We develop a perturbative approach to redshift space distortions (RSD) using the phase space distribution function approach and apply it to the dark matter redshift space power spectrum and its moments. RSD can be written as a sum over density weighted velocity moments correlators, with the lowest order being density, momentum density and stress energy density. We use standard and extended perturbation theory (PT) to determine their auto and cross correlators, comparing them to N-body simulations. We show which of the terms can be modeled well with the standard PT and which need additional terms that include higher order correctionsmore » which cannot be modeled in PT. Most of these additional terms are related to the small scale velocity dispersion effects, the so called finger of god (FoG) effects, which affect some, but not all, of the terms in this expansion, and which can be approximately modeled using a simple physically motivated ansatz such as the halo model. We point out that there are several velocity dispersions that enter into the detailed RSD analysis with very different amplitudes, which can be approximately predicted by the halo model. In contrast to previous models our approach systematically includes all of the terms at a given order in PT and provides a physical interpretation for the small scale dispersion values. We investigate RSD power spectrum as a function of μ, the cosine of the angle between the Fourier mode and line of sight, focusing on the lowest order powers of μ and multipole moments which dominate the observable RSD power spectrum. Overall we find considerable success in modeling many, but not all, of the terms in this expansion. This is similar to the situation in real space, but predicting power spectrum in redshift space is more difficult because of the explicit influence of small scale dispersion type effects in RSD, which extend to very large scales.« less

THE OPEN SOURCING OF EPANET

EPA Science Inventory

A proposal was made at the 2009 EWRI Congress in Kansas City, MO to establish an Open Source Project (OSP) for the widely used EPANET pipe network analysis program. This would be an ongoing collaborative effort among a group of geographically dispersed advisors and developers, wo...

Evaluation of the ability of calcite, bentonite and barite to enhance oil dispersion under arctic conditions.

PubMed

Jézéquel, Ronan; Receveur, Justine; Nedwed, Tim; Le Floch, Stéphane

2018-02-01

A test program was conducted at laboratory and pilot scale to assess the ability of clays used in drilling mud (calcite, bentonite and barite) to create oil-mineral aggregates and disperse crude oil under arctic conditions. Laboratory tests were performed in order to determine the most efficient conditions (type of clay, MOR (Mineral/Oil Ratio), mixing energy) for OMA (Oil Mineral Aggregate) formation. The dispersion rates of four crude oils were assessed at two salinities. Dispersion was characterized in terms of oil concentration in the water column and median OMA size. Calcite appeared to be the best candidate at a MOR of 2:5. High mixing energy was required to initiate OMA formation and low energy was then necessary to prevent the OMAs from resurfacing. Oil dispersion using Corexit 9500 was compared with oil dispersion using mineral fines. Copyright © 2017 Elsevier Ltd. All rights reserved.

A space-time discretization procedure for wave propagation problems

NASA Technical Reports Server (NTRS)

Davis, Sanford

1989-01-01

Higher order compact algorithms are developed for the numerical simulation of wave propagation by using the concept of a discrete dispersion relation. The dispersion relation is the imprint of any linear operator in space-time. The discrete dispersion relation is derived from the continuous dispersion relation by examining the process by which locally plane waves propagate through a chosen grid. The exponential structure of the discrete dispersion relation suggests an efficient splitting of convective and diffusive terms for dissipative waves. Fourth- and eighth-order convection schemes are examined that involve only three or five spatial grid points. These algorithms are subject to the same restrictions that govern the use of dispersion relations in the constructions of asymptotic expansions to nonlinear evolution equations. A new eighth-order scheme is developed that is exact for Courant numbers of 1, 2, 3, and 4. Examples are given of a pulse and step wave with a small amount of physical diffusion.

The Roles of Dispersal, Fecundity, and Predation in the Population Persistence of an Oak (Quercus engelmannii) under Global Change

PubMed Central

Conlisk, Erin; Lawson, Dawn; Syphard, Alexandra D.; Franklin, Janet; Flint, Lorraine; Flint, Alan; Regan, Helen M.

2012-01-01

A species’ response to climate change depends on the interaction of biotic and abiotic factors that define future habitat suitability and species’ ability to migrate or adapt. The interactive effects of processes such as fire, dispersal, and predation have not been thoroughly addressed in the climate change literature. Our objective was to examine how life history traits, short-term global change perturbations, and long-term climate change interact to affect the likely persistence of an oak species - Quercus engelmannii (Engelmann oak). Specifically, we combined dynamic species distribution models, which predict suitable habitat, with stochastic, stage-based metapopulation models, which project population trajectories, to evaluate the effects of three global change factors – climate change, land use change, and altered fire frequency – emphasizing the roles of dispersal and seed predation. Our model predicted dramatic reduction in Q. engelmannii abundance, especially under drier climates and increased fire frequency. When masting lowers seed predation rates, decreased masting frequency leads to large abundance decreases. Current rates of dispersal are not likely to prevent these effects, although increased dispersal could mitigate population declines. The results suggest that habitat suitability predictions by themselves may under-estimate the impact of climate change for other species and locations. PMID:22623955

The Physics of Foams, Droplets and Bubbles

ERIC Educational Resources Information Center

Sarker, Dipak K.

2013-01-01

Foams or bubble dispersions are common to milkshakes, bread, champagne froth, shaving mousse, shampoo, crude oil extraction systems, upholstery packing and bubble wrap, whereas the term droplet is often synonymous with either a small drop of water or a drop of oil--a type of coarse dispersion. The latter are seen in butter and milk, household…

Landscape resistnace to dispersal: Predicting long-term effects of human disturbance on a small and isolated wolf population in southwestern Manitoba, Canada

EPA Science Inventory

Landscape fragmentation affects wildlife population viability, in part through the effects it has on individual dispersal. Agricultural development over the past 60 years has resulted in considerable habitat fragmentation in the Riding Mountain National Park (RMNP) region in sou...

Investigation of the potential for long-range transport of mercury to the Everglades using the organic chemistry integrated dispersion (ORCHID) model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burns, D.S.; Kienzle, M.A.; Ferris, D.C.

1996-12-31

The objective of this study is to identify potential long-range sources of mercury within the southeast region of the United States. Preliminary results of a climatological study using the Short-range Layered Atmospheric Model (SLAM) transport model from a select source in the southeast U.S. are presented. The potential for long-range transport from Oak Ridge, Tennessee to Florida is discussed. The transport and transformation of mercury during periods of favorable transport to south Florida is modeled using the Organic Chemistry Integrated Dispersion (ORCHID) model, which contains the transport model used in the climatology study. SLAM/ORCHID results indicate the potential for mercurymore » reaching southeast Florida from the source and the atmospheric oxidation of mercury during transport.« less

Investigation of holdup and axial dispersion of liquid phase in a catalytic exchange column using radiotracer technique.

PubMed

Kumar, Rajesh; Pant, H J; Goswami, Sunil; Sharma, V K; Dash, A; Mishra, S; Bhanja, K; Mohan, Sadhana; Mahajani, S M

2017-03-01

Holdup and axial dispersion of liquid phase in a catalytic exchange column were investigated by measuring residence time distributions (RTD) using a radiotracer technique. RTD experiments were independently carried out with two different types of packings i.e. hydrophobic water-repellent supported platinum catalyst and a mixture (50% (v/v)) of hydrophobic catalyst and a hydrophillic wettable packing were used in the column. Mean residence times and hold-ups of the liquid phase were estimated at different operating conditions. Axial dispersion model (ADM) and axial dispersion with exchange model (ADEM) were used to simulate the measured RTD data. Both the models were found equally suitable to describe the measured data. The degree of axial mixing was estimated in terms of Peclet number (Pe) and Bodenstein number (Bo). Based on the obtained parameters of the ADM, correlations for total liquid hold-up (H T ) and axial mixing in terms of Bo were proposed for design and scale up of the full-scale catalytic exchange column. Copyright © 2016 Elsevier Ltd. All rights reserved.

Dynamics of a Nonlocal Dispersal Model with a Nonlocal Reaction Term

NASA Astrophysics Data System (ADS)

Ma, Li; Guo, Shangjiang; Chen, Ting

In this paper, we study a class of nonlocal dispersal problem with a nonlocal term arising in population dynamics: ut = 𝒟u + u λ ‑ f(u) ‑∫ΩK(x,y)g(u(y))dy,in Ω × (0, +∞), u(x, 0) = u0(x) ≥ 0, in Ω,u = 0, in ℝN\\Ω × (0, +∞), where Ω ⊂ ℝN (N ≥ 1) is a bounded domain, λ ∈ ℝ, 𝒟u(x,t) =∫ΩJ(x ‑ y)[u(y,t) ‑ u(x,t)]dy represents the nonlocal dispersal operator with continuous and non-negative dispersal kernel. The kernel K ∈ C(Ω¯ ×Ω¯) is assumed to be non-negative and is allowed to have a degeneracy in a smooth subdomain Ω0 of Ω. When K is either positive or vanishes in a subdomain, we respectively investigate the existence, multiplicity and asymptotical stability of positive steady states under the local/global variation of parameter by means of sub-supersolution method, Lyapunov-Schmidt reduction, and bifurcation theory.

Habitat filtering not dispersal limitation shapes oceanic island floras: species assembly of the Galápagos archipelago.

PubMed

Carvajal-Endara, Sofía; Hendry, Andrew P; Emery, Nancy C; Davies, T Jonathan

2017-04-01

Remote locations, such as oceanic islands, typically harbour relatively few species, some of which go on to generate endemic radiations. Species colonising these locations tend to be a non-random subset from source communities, which is thought to reflect dispersal limitation. However, non-random colonisation could also result from habitat filtering, whereby only a few continental species can become established. We evaluate the imprints of these processes on the Galápagos flora by analysing a comprehensive regional phylogeny for ~ 39 000 species alongside information on dispersal strategies and climatic suitability. We found that habitat filtering was more important than dispersal limitation in determining species composition. This finding may help explain why adaptive radiation is common on oceanic archipelagoes - because colonising species can be relatively poor dispersers with specific niche requirements. We suggest that the standard assumption that plant communities in remote locations are primarily shaped by dispersal limitation deserves reconsideration. © 2017 John Wiley & Sons Ltd/CNRS.

Microscale Obstacle Resolving Air Quality Model Evaluation with the Michelstadt Case

PubMed Central

Rakai, Anikó; Kristóf, Gergely

2013-01-01

Modelling pollutant dispersion in cities is challenging for air quality models as the urban obstacles have an important effect on the flow field and thus the dispersion. Computational Fluid Dynamics (CFD) models with an additional scalar dispersion transport equation are a possible way to resolve the flowfield in the urban canopy and model dispersion taking into consideration the effect of the buildings explicitly. These models need detailed evaluation with the method of verification and validation to gain confidence in their reliability and use them as a regulatory purpose tool in complex urban geometries. This paper shows the performance of an open source general purpose CFD code, OpenFOAM for a complex urban geometry, Michelstadt, which has both flow field and dispersion measurement data. Continuous release dispersion results are discussed to show the strengths and weaknesses of the modelling approach, focusing on the value of the turbulent Schmidt number, which was found to give best statistical metric results with a value of 0.7. PMID:24027450

Microscale obstacle resolving air quality model evaluation with the Michelstadt case.

PubMed

Rakai, Anikó; Kristóf, Gergely

2013-01-01

Modelling pollutant dispersion in cities is challenging for air quality models as the urban obstacles have an important effect on the flow field and thus the dispersion. Computational Fluid Dynamics (CFD) models with an additional scalar dispersion transport equation are a possible way to resolve the flowfield in the urban canopy and model dispersion taking into consideration the effect of the buildings explicitly. These models need detailed evaluation with the method of verification and validation to gain confidence in their reliability and use them as a regulatory purpose tool in complex urban geometries. This paper shows the performance of an open source general purpose CFD code, OpenFOAM for a complex urban geometry, Michelstadt, which has both flow field and dispersion measurement data. Continuous release dispersion results are discussed to show the strengths and weaknesses of the modelling approach, focusing on the value of the turbulent Schmidt number, which was found to give best statistical metric results with a value of 0.7.

Spatial heterogeneity in the effects of climate and density-dependence on dispersal in a house sparrow metapopulation

PubMed Central

Pärn, Henrik; Ringsby, Thor Harald; Jensen, Henrik; Sæther, Bernt-Erik

2012-01-01

Dispersal plays a key role in the response of populations to climate change and habitat fragmentation. Here, we use data from a long-term metapopulation study of a non-migratory bird, the house sparrow (Passer domesticus), to examine the influence of increasing spring temperature and density-dependence on natal dispersal rates and how these relationships depend on spatial variation in habitat quality. The effects of spring temperature and population size on dispersal rate depended on the habitat quality. Dispersal rate increased with temperature and population size on poor-quality islands without farms, where house sparrows were more exposed to temporal fluctuations in weather conditions and food availability. By contrast, dispersal rate was independent of spring temperature and population size on high-quality islands with farms, where house sparrows had access to food and shelter all the year around. This illustrates large spatial heterogeneity within the metapopulation in how population density and environmental fluctuations affect the dispersal process. PMID:21613299

Existence and stability of dispersive solutions to the Kadomtsev-Petviashvili equation in the presence of dispersion effect

NASA Astrophysics Data System (ADS)

Das, Amiya; Ganguly, Asish

2017-07-01

The paper deals with Kadomtsev-Petviashvili (KP) equation in presence of a small dispersion effect. The nature of solutions are examined under the dispersion effect by using Lyapunov function and dynamical system theory. We prove that when dispersion is added to the KP equation, in certain regions, yet there exist bounded traveling wave solutions in the form of solitary waves, periodic and elliptic functions. The general solution of the equation with or without the dispersion effect are obtained in terms of Weirstrass ℘ functions and Jacobi elliptic functions. New form of kink-type solutions are established by exploring a new technique based on factorization method, use of functional transformation and the Abel's first order nonlinear equation. Furthermore, the stability analysis of the dispersive solutions are examined which shows that the traveling wave velocity is a bifurcation parameter which governs between different classes of waves. We use the phase plane analysis and show that at a critical velocity, the solution has a transcritical bifurcation.

Simulated distribution and ecotoxicity-based assessment of chemically-dispersed oil in Tokyo Bay.

PubMed

Koyama, Jiro; Imakado, Chie; Uno, Seiichi; Kuroda, Takako; Hara, Shouichi; Majima, Takahiro; Shirota, Hideyuki; Añasco, Nathaniel C

2014-08-30

To assess risks of chemically-dispersed oil to marine organisms, oil concentrations in the water were simulated using a hypothetical spill accident in Tokyo Bay. Simulated oil concentrations were then compared with the short-term no-observed effect concentration (NOEC), 0.01 mg/L, obtained through toxicity tests using marine diatoms, amphipod and fish. Area of oil concentrations higher than the NOEC were compared with respect to use and non-use of dispersant. Results of the simulation show relatively faster dispersion near the mouth of the bay compared to its inner sections which is basically related to its stronger water currents. Interestingly, in the inner bay, a large area of chemically-dispersed oil has concentrations higher than the NOEC. It seems emulsifying oil by dispersant increases oil concentrations, which could lead to higher toxicity to aquatic organisms. When stronger winds occur, however, the difference in toxic areas between use and non-use of dispersant is quite small. Copyright © 2014 Elsevier Ltd. All rights reserved.

Influence of dispersing agents and solution conditions on the solubility of crude kaolin.

PubMed

Zaman, Abbas A; Mathur, Sharad

2004-03-01

Experiments measuring the solubility of kaolin particles in terms of the concentration of aluminum and silicon ions in supernatant were carried out as a function of the pH of the slurry over a wide range of dosages of different dispersing agents varying from 0.5 to 12 mg/(g solids). The concentrations of the metal ions in supernatant were found to be strongly affected by the type and the dosage of the dispersants and pH of the solution. In this study, the mechanism of the reaction between the dispersing agents and kaolin particles was studied and the dissolution capacities of metal ions (aluminum and silicon) were identified from kaolin particles in the absence and presence of dispersing agents. The three anionic dispersing agents used were sodium polyacrylate (Na-PAA), sodium hexametaphosphate (Na-HMP), and sodium silicate (Na-silicate), based on the industrial application of these agents and their ability to produce a stable dispersion for this purpose.

Integrating individual movement behaviour into dispersal functions.

PubMed

Heinz, Simone K; Wissel, Christian; Conradt, Larissa; Frank, Karin

2007-04-21

Dispersal functions are an important tool for integrating dispersal into complex models of population and metapopulation dynamics. Most approaches in the literature are very simple, with the dispersal functions containing only one or two parameters which summarise all the effects of movement behaviour as for example different movement patterns or different perceptual abilities. The summarising nature of these parameters makes assessing the effect of one particular behavioural aspect difficult. We present a way of integrating movement behavioural parameters into a particular dispersal function in a simple way. Using a spatial individual-based simulation model for simulating different movement behaviours, we derive fitting functions for the functional relationship between the parameters of the dispersal function and several details of movement behaviour. This is done for three different movement patterns (loops, Archimedean spirals, random walk). Additionally, we provide measures which characterise the shape of the dispersal function and are interpretable in terms of landscape connectivity. This allows an ecological interpretation of the relationships found.

Chemical dispersion of oil with mineral fines in a low temperature environment.

PubMed

Wang, Weizhi; Zheng, Ying; Lee, Kenneth

2013-07-15

The increasing risks of potential oil spills in the arctic regions, which are characterized by low temperatures, are a big challenge. The traditional dispersant method has shown limited effectiveness in oil cleanup. This work studied the role of mineral fines in the formation of oil-mineral aggregates (OMAs) at low temperature (0-4 °C) environment. The loading amount of minerals and dispersant with different dispersant and oil types were investigated under a full factorial design. The shapes and sizes of OMAs were analyzed. Results showed that the behavior of OMA formation differs when dispersant and mineral fines are used individually or together. Both the experimental and microscopic results also showed the existence of optimal dispersant to oil ratios and mineral to oil ratios. In general, poor oil removal performance was observed for more viscous oil. Corexit 9500 performed better than Corexit 9527 with various oils, in terms of oil dispersion and OMA formation. Copyright © 2013 Elsevier Ltd. All rights reserved.

Evaluation of the inverse dispersion modelling method for estimating ammonia multi-source emissions using low-cost long time averaging sensor

NASA Astrophysics Data System (ADS)

Loubet, Benjamin; Carozzi, Marco

2015-04-01

Tropospheric ammonia (NH3) is a key player in atmospheric chemistry and its deposition is a threat for the environment (ecosystem eutrophication, soil acidification and reduction in species biodiversity). Most of the NH3 global emissions derive from agriculture, mainly from livestock manure (storage and field application) but also from nitrogen-based fertilisers. Inverse dispersion modelling has been widely used to infer emission sources from a homogeneous source of known geometry. When the emission derives from different sources inside of the measured footprint, the emission should be treated as multi-source problem. This work aims at estimating whether multi-source inverse dispersion modelling can be used to infer NH3 emissions from different agronomic treatment, composed of small fields (typically squares of 25 m side) located near to each other, using low-cost NH3 measurements (diffusion samplers). To do that, a numerical experiment was designed with a combination of 3 x 3 square field sources (625 m2), and a set of sensors placed at the centre of each field at several heights as well as at 200 m away from the sources in each cardinal directions. The concentration at each sensor location was simulated with a forward Lagrangian Stochastic (WindTrax) and a Gaussian-like (FIDES) dispersion model. The concentrations were averaged over various integration times (3 hours to 28 days), to mimic the diffusion sampler behaviour with several sampling strategy. The sources were then inferred by inverse modelling using the averaged concentration and the same models in backward mode. The sources patterns were evaluated using a soil-vegetation-atmosphere model (SurfAtm-NH3) that incorporates the response of the NH3 emissions to surface temperature. A combination emission patterns (constant, linear decreasing, exponential decreasing and Gaussian type) and strengths were used to evaluate the uncertainty of the inversion method. Each numerical experiment covered a period of 28 days. The meteorological dataset of the fluxnet FR-Gri site (Grignon, FR) in 2008 was employed. Several sensor heights were tested, from 0.25 m to 2 m. The multi-source inverse problem was solved based on several sampling and field trial strategies: considering 1 or 2 heights over each field, considering the background concentration as known or unknown, and considering block-repetitions in the field set-up (3 repetitions). The inverse modelling approach demonstrated to be adapted for discriminating large differences in NH3 emissions from small agronomic plots using integrating sensors. The method is sensitive to sensor heights. The uncertainties and systematic biases are evaluated and discussed.

The role of sea ice for vascular plant dispersal in the Arctic

PubMed Central

Ehrich, Dorothee; Bennike, Ole; Geirsdottir, Aslaug

2016-01-01

Sea ice has been suggested to be an important factor for dispersal of vascular plants in the Arctic. To assess its role for postglacial colonization in the North Atlantic region, we compiled data on the first Late Glacial to Holocene occurrence of vascular plant species in East Greenland, Iceland, the Faroe Islands and Svalbard. For each record, we reconstructed likely past dispersal events using data on species distributions and genetics. We compared these data to sea-ice reconstructions to evaluate the potential role of sea ice in these past colonization events and finally evaluated these results using a compilation of driftwood records as an independent source of evidence that sea ice can disperse biological material. Our results show that sea ice was, in general, more prevalent along the most likely dispersal routes at times of assumed first colonization than along other possible routes. Also, driftwood is frequently dispersed in regions that have sea ice today. Thus, sea ice may act as an important dispersal agent. Melting sea ice may hamper future dispersal of Arctic plants and thereby cause more genetic differentiation. It may also limit the northwards expansion of competing boreal species, and hence favour the persistence of Arctic species. PMID:27651529

Radioactivity impacts of the Fukushima Nuclear Accident on the atmosphere

NASA Astrophysics Data System (ADS)

Lin, W.; Chen, L.; Yu, W.; Ma, H.; Zeng, Z.; Lin, J.; Zeng, S.

2015-02-01

The Fukushima Nuclear Accident (FNA) resulted in a large amount of radionuclides released into the atmosphere and dispersed globally, which has greatly raised public concerns. The state of the art for source terms of 19 kinds of radionuclides derived from the FNA was comprehensively collected and compared with levels of the global fallout and the Chernobyl Nuclear Accident (CNA). The atmospheric impacts of the FNA were evaluated from three aspects including radioactive baseline of the atmosphere, the concentration limits in standards and radiological protection. The FNA should not impose significant radiological risk on the public members in the countries excluding Japan. A conceptual scheme of Fukushima-derived radionuclides with physical and physicochemical insights on different temporal-spatial timescales was discussed and illustrated to understand their fates in the atmosphere.

Optimisation of dispersion parameters of Gaussian plume model for CO₂ dispersion.

PubMed

Liu, Xiong; Godbole, Ajit; Lu, Cheng; Michal, Guillaume; Venton, Philip

2015-11-01

The carbon capture and storage (CCS) and enhanced oil recovery (EOR) projects entail the possibility of accidental release of carbon dioxide (CO2) into the atmosphere. To quantify the spread of CO2 following such release, the 'Gaussian' dispersion model is often used to estimate the resulting CO2 concentration levels in the surroundings. The Gaussian model enables quick estimates of the concentration levels. However, the traditionally recommended values of the 'dispersion parameters' in the Gaussian model may not be directly applicable to CO2 dispersion. This paper presents an optimisation technique to obtain the dispersion parameters in order to achieve a quick estimation of CO2 concentration levels in the atmosphere following CO2 blowouts. The optimised dispersion parameters enable the Gaussian model to produce quick estimates of CO2 concentration levels, precluding the necessity to set up and run much more complicated models. Computational fluid dynamics (CFD) models were employed to produce reference CO2 dispersion profiles in various atmospheric stability classes (ASC), different 'source strengths' and degrees of ground roughness. The performance of the CFD models was validated against the 'Kit Fox' field measurements, involving dispersion over a flat horizontal terrain, both with low and high roughness regions. An optimisation model employing a genetic algorithm (GA) to determine the best dispersion parameters in the Gaussian plume model was set up. Optimum values of the dispersion parameters for different ASCs that can be used in the Gaussian plume model for predicting CO2 dispersion were obtained.

Dispersion relations for $$\\eta '\\rightarrow \\eta \\pi \\pi $$

DOE Office of Scientific and Technical Information (OSTI.GOV)

Isken, Tobias; Kubis, Bastian; Schneider, Sebastian P.

Here, we present a dispersive analysis of the decay amplitude for η' → ηππ that is based on the fundamental principles of analyticity and unitarity. In this framework, final-state interactions are fully taken into account. Our dispersive representation relies only on input for the ππ and πη scattering phase shifts. Isospin symmetry allows us to describe both the charged and neutral decay channel in terms of the same function. The dispersion relation contains subtraction constants that cannot be fixed by unitarity.We determine these parameters by a fit to Dalitz-plot data from the VES and BES-III experiments. We study the predictionmore » of a low-energy theorem and compare the dispersive fit to variants of chiral perturbation theory.« less

Dispersion relations for $$\\eta '\\rightarrow \\eta \\pi \\pi $$

DOE PAGES

Isken, Tobias; Kubis, Bastian; Schneider, Sebastian P.; ...

2017-07-21

Here, we present a dispersive analysis of the decay amplitude for η' → ηππ that is based on the fundamental principles of analyticity and unitarity. In this framework, final-state interactions are fully taken into account. Our dispersive representation relies only on input for the ππ and πη scattering phase shifts. Isospin symmetry allows us to describe both the charged and neutral decay channel in terms of the same function. The dispersion relation contains subtraction constants that cannot be fixed by unitarity.We determine these parameters by a fit to Dalitz-plot data from the VES and BES-III experiments. We study the predictionmore » of a low-energy theorem and compare the dispersive fit to variants of chiral perturbation theory.« less

Using an epiphytic moss to identify previously unknown sources of atmospheric cadmium pollution

Treesearch

Geoffrey H. Donovan; Sarah E. Jovan; Demetrios Gatziolis; Igor Burstyn; Yvonne L. Michael; Michael C. Amacher; Vicente J. Monleon

2016-01-01

Urban networks of air-quality monitors are often too widely spaced to identify sources of air pollutants, especially if they do not disperse far from emission sources. The objectives of this study were to test the use of moss bio-indicators to develop a fine-scale map of atmospherically-derived cadmium and to identify the sources of cadmium in a complex urban setting....

Estimation of the time-dependent radioactive source-term from the Fukushima nuclear power plant accident using atmospheric transport modelling

NASA Astrophysics Data System (ADS)

Schoeppner, M.; Plastino, W.; Budano, A.; De Vincenzi, M.; Ruggieri, F.

2012-04-01

Several nuclear reactors at the Fukushima Dai-ichi power plant have been severely damaged from the Tōhoku earthquake and the subsequent tsunami in March 2011. Due to the extremely difficult on-site situation it has been not been possible to directly determine the emissions of radioactive material. However, during the following days and weeks radionuclides of 137-Caesium and 131-Iodine (amongst others) were detected at monitoring stations throughout the world. Atmospheric transport models are able to simulate the worldwide dispersion of particles accordant to location, time and meteorological conditions following the release. The Lagrangian atmospheric transport model Flexpart is used by many authorities and has been proven to make valid predictions in this regard. The Flexpart software has first has been ported to a local cluster computer at the Grid Lab of INFN and Department of Physics of University of Roma Tre (Rome, Italy) and subsequently also to the European Mediterranean Grid (EUMEDGRID). Due to this computing power being available it has been possible to simulate the transport of particles originating from the Fukushima Dai-ichi plant site. Using the time series of the sampled concentration data and the assumption that the Fukushima accident was the only source of these radionuclides, it has been possible to estimate the time-dependent source-term for fourteen days following the accident using the atmospheric transport model. A reasonable agreement has been obtained between the modelling results and the estimated radionuclide release rates from the Fukushima accident.

OCD: The offshore and coastal dispersion model. Volume 1. User's guide

DOE Office of Scientific and Technical Information (OSTI.GOV)

DiCristofaro, D.C.; Hanna, S.R.

1989-11-01

The Offshore and Coastal Dispersion (OCD) Model has been developed to simulate the effect of offshore emissions from point, area, or line sources on the air quality of coastal regions. The OCD model was adapted from the EPA guideline model MPTER (EPA, 1980). Modifications were made to incorporate overwater plume transport and dispersion as well as changes that occur as the plume crosses the shoreline. This is a revised OCD model, the fourth version to date. The volume is the User's Guide which includes a Model overview, technical description, user's instructions, and notes on model evaluation and results.

2.3. Global-scale atmospheric dispersion of microorganisms

USGS Publications Warehouse

Griffin, Dale W.; Gonzalez-Martin, Cristina; Hoose, C.; Smith, D.J.; Delort, Anne-Marie; Amato, Pierre

2018-01-01

This chapter addresses long-range dispersion and the survival of microorganisms across a wide range of altitudes in Earth's atmosphere. Topics include mechanisms of dispersion, survivability of microorganisms known to be associated with long-range transport, natural and artificial sources of bioaerosols, residence time estimation through the use of proxy aerosols, transport and emission models, and monitoring assays (both culture and molecular based). We conclude with a discussion of the known limits for Earth's biosphere boundary, relating aerobiology studies to planetary exploration given the large degree of overlapping requirements for in situ studies (including low biomass life detection and contamination control).

Method of generating hydrogen gas from sodium borohydride

DOEpatents

Kravitz, Stanley H.; Hecht, Andrew M.; Sylwester, Alan P.; Bell, Nelson S.

2007-12-11

A compact solid source of hydrogen gas, where the gas is generated by contacting water with micro-disperse particles of sodium borohydride in the presence of a catalyst, such as cobalt or ruthenium. The micro-disperse particles can have a substantially uniform diameter of 1-10 microns, and preferably about 3-5 microns. Ruthenium or cobalt catalytic nanoparticles can be incorporated in the micro-disperse particles of sodium borohydride, which allows a rapid and complete reaction to occur without the problems associated with caking and scaling of the surface by the reactant product sodium metaborate. A closed loop water management system can be used to recycle wastewater from a PEM fuel cell to supply water for reacting with the micro-disperse particles of sodium borohydride in a compact hydrogen gas generator. Capillary forces can wick water from a water reservoir into a packed bed of micro-disperse fuel particles, eliminating the need for using an active pump.

Dispersions of attractive semiflexible fiberlike colloidal particles from bacterial cellulose microfibrils.

PubMed

Kuijk, Anke; Koppert, Remco; Versluis, Peter; van Dalen, Gerard; Remijn, Caroline; Hazekamp, Johan; Nijsse, Jaap; Velikov, Krassimir P

2013-11-26

We prepared dispersions from bacterial cellulose microfibrils (CMF) of a commercial Nata de Coco source. We used an ultra-high-energy mechanical deagglomeration process that is able to disperse the CMFs from the pellicle in which they are organized in an irregular network. Because of the strong attractions between the CMFs, the dispersion remained highly heterogeneous, consisting of fiber bundles, flocs, and voids spanning tens to hundreds of micrometers depending on concentration. The size of these flocs increased with CMF concentration, the size of the bundles stayed constant, and the size of the voids decreased. The observed percolation threshold in MFC dispersions is lower than the theoretical prediction, which is accounted for by the attractive interactions in the system. Because bacterial cellulose is chemically very pure, it can be used to study the interaction of attractive and highly shape-anisotropic, semiflexible fiberlike colloidal particles.

Modeling of dispersion near roadways based on the vehicle-induced turbulence concept

NASA Astrophysics Data System (ADS)

Sahlodin, Ali M.; Sotudeh-Gharebagh, Rahmat; Zhu, Yifang

A mathematical model is developed for dispersion near roadways by incorporating vehicle-induced turbulence (VIT) into Gaussian dispersion modeling using computational fluid dynamics (CFD). The model is based on the Gaussian plume equation in which roadway is regarded as a series of point sources. The Gaussian dispersion parameters are modified by simulation of the roadway using CFD in order to evaluate turbulent kinetic energy (TKE) as a measure of VIT. The model was evaluated against experimental carbon monoxide concentrations downwind of two major freeways reported in the literature. Good agreements were achieved between model results and the literature data. A significant difference was observed between the model results with and without considering VIT. The difference is rather high for data very close to the freeways. This model, after evaluation with additional data, may be used as a framework for predicting dispersion and deposition from any roadway for different traffic (vehicle type and speed) conditions.

Source-receptor matrix calculation with a Lagrangian particle dispersion model in backward mode

NASA Astrophysics Data System (ADS)

Seibert, P.; Frank, A.

2004-01-01

The possibility to calculate linear-source receptor relationships for the transport of atmospheric trace substances with a Lagrangian particle dispersion model (LPDM) running in backward mode is shown and presented with many tests and examples. This mode requires only minor modifications of the forward LPDM. The derivation includes the action of sources and of any first-order processes (transformation with prescribed rates, dry and wet deposition, radioactive decay, etc.). The backward mode is computationally advantageous if the number of receptors is less than the number of sources considered. The combination of an LPDM with the backward (adjoint) methodology is especially attractive for the application to point measurements, which can be handled without artificial numerical diffusion. Practical hints are provided for source-receptor calculations with different settings, both in forward and backward mode. The equivalence of forward and backward calculations is shown in simple tests for release and sampling of particles, pure wet deposition, pure convective redistribution and realistic transport over a short distance. Furthermore, an application example explaining measurements of Cs-137 in Stockholm as transport from areas contaminated heavily in the Chernobyl disaster is included.

Evaluation of the Combined AERCOARE/AERMOD Modeling Approach for Offshore Sources

EPA Science Inventory

ENVIRON conducted an evaluation of the combined AERCOARE/AERMOD (AERCOARE-MOD) modeling approach for offshore sources using tracer data from four field studies. AERCOARE processes overwater meteorological data for use by the AERMOD air quality dispersion model (EPA, 2004a). AERC...

NEAR ROAD NITRIC OXIDE AND HYDROCARBON MEASUREMENTS WITH DUV-DOAS

EPA Science Inventory

As part of the overall EPA effort to increase understanding of the distribution of air pollutants in near road environments, optical remote sensing techniques developed for area source measurement are being used to assess mobile source emissions and dispersion from roadway segmen...

APPLYING OPEN-PATH OPTICAL SPECTROSCOPY TO HEAVY-DUTY DIESEL EMISSIONS

EPA Science Inventory

Non-dispersive infrared absorption has been used to measure gaseous emissions for both stationary and mobile sources. Fourier transform infrared spectroscopy has been used for stationary sources as both extractive and open-path methods. We have applied the open-path method for bo...

40 CFR 51.164 - Stack height procedures.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 51.164 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS... source's stack height that exceeds good engineering practice or by any other dispersion technique, except... source based on a good engineering practice stack height that exceeds the height allowed by § 51.100(ii...

The Effects of Dispersal and Predator Density on Prey Survival in an Insect-Red Clover Metacommunity

PubMed Central

Radl, James N; Crist, Thomas O

2018-01-01

Abstract Trophic interactions are often studied within habitat patches, but among-patch dispersal of individuals may influence local patch dynamics. Metacommunity concepts incorporate the effects of dispersal on local and community dynamics. There are few experimental tests of metacommunity theory using insects compared to those conducted in microbial microcosms. Using connected experimental mesocosms, we varied the density of the leafhopper Agallia constricta Van Duzee (Homoptera: Cicadellidae) and a generalist insect predator, the damsel bug (Nabis spp., Heteroptera: Nabidae), to determine the effects of conspecific and predator density and varying the time available to dispersal among mesocosms on predation rates, dispersal rates, and leafhopper survival. Conspecific and damsel bug density did not affect dispersal rates in leafhoppers, but this may be due to leafhoppers’ aversion to leaving the host plants or the connecting tubes between mesocosms hindering leafhopper movement. Leafhopper dispersal was higher in high-dispersal treatments. Survival rates of A. constricta were also lowest in treatments where dispersal was not limited. This is one of the first experimental studies to vary predator density and the time available to dispersal. Our results indicate that dispersal is the key to understanding short-term processes such as prey survival in predator-prey metacommunities. Further work is needed to determine how dispersal rates influence persistence of communities in multigenerational studies. PMID:29301047

Atmospheric transport and deposition of radionuclides released after the Fukushima Dai-chi accident and resulting effective dose

NASA Astrophysics Data System (ADS)

Marzo, Giuseppe A.

2014-09-01

On 11 March 2011 an earthquake off the Pacific coast of the Fukushima prefecture generated a tsunami that hit Fukushima Dai-ichi and Fukushima Da-ini Nuclear Power Plants. From 12 March a significant amount of radioactive material was released into the atmosphere and dispersed worldwide. Among the most abundant radioactive species released were iodine and cesium isotopes. By means of an atmospheric dispersion Lagrangian code and publicly available meteorological data, the atmospheric dispersion of 131I, 134Cs, and 137Cs have been simulated for three months after the event with a spatial resolution of 0.5° × 0.5° globally. The simulation has been validated by comparison to publicly available measurements collected in 206 locations worldwide. Sensitivity analysis shows that release height of the radionuclides, wet deposition velocity, and source term are the parameters with the most impact on the simulation results. The simulation shows that the radioactive plume, consisting of about 200 PBq by adding contributions from 131I, 134Cs, and 137Cs, has been transported over the entire northern hemisphere depositing up to 1.2 MBq m-2 nearby the NPPs to less than 20 Bq m-2 in Europe. The consequent effective dose to the population over a 50-year period, calculated by considering both external and internal pathways of exposure, is found to be about 40 mSv in the surroundings of Fukushima Dai-ichi, while other countries in the northern hemisphere experienced doses several orders of magnitude lower suggesting a small impact on the population health elsewhere.

Estimates of connectivity reveal non-equilibrium epiphyte occurrence patterns almost 180 years after habitat decline.

PubMed

Johansson, Victor; Snäll, Tord; Ranius, Thomas

2013-06-01

Habitat loss is a major cause of species decline and extinction. Immediately after habitat loss, species occurrences are not in equilibrium with the new landscape and more closely reflect the previous landscape structure. Species with slow colonisation-extinction dynamics may display long time-lags before reaching a new equilibrium. We investigated the importance of connectivity to current and historical dispersal sources with the aim of explaining the occurrence pattern of epiphytic lichens with different traits among 104 old oaks. We used oak survey data collected from 1830 and 2009 for a Swedish landscape where oak densities declined drastically shortly after 1830. We fitted a commonly used connectivity measure and estimated the confidence interval for the spatial scale parameter. Small differences in the spatial scale parameter resulted in large differences in model fit. Connectivity to trees in 1830 better explained the occurrence of three of the four species compared to the connectivity in 2009. The explanatory power of the historical landscape structure was highest for the species with traits that may result in a low colonisation rate--both a narrow niche (here few suitable trees) and large dispersal propagules. The results suggest that oak-dependent epiphytic lichens have not reached equilibrium with the spatial landscape structure 180 years after the drastic decline in habitat. For the long-term persistence of epiphytes associated with old trees, conservation efforts should focus on (1) protecting and restoring stands where specialised species with large dispersal propagules (i.e. with low colonisation rates) occur today and (2) promoting tree regeneration in their near vicinity.

AMR Code Simulations of Turbulent Combustion in Confined and Unconfined SDF Explosions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kuhl, A L; Bell, J B; Beckner, V

2009-05-29

A heterogeneous continuum model is proposed to describe the dispersion and combustion of an aluminum particle cloud in an explosion. It combines the gas-dynamic conservation laws for the gas phase with a continuum model for the dispersed phase, as formulated by Nigmatulin. Inter-phase mass, momentum and energy exchange are prescribed by phenomenological models. It incorporates a combustion model based on the mass conservation laws for fuel, air and products; source/sink terms are treated in the fast-chemistry limit appropriate for such gas dynamic fields, along with a model for mass transfer from the particle phase to the gas. The model takesmore » into account both the afterburning of the detonation products of the booster with air, and the combustion of the Al particles with air. The model equations were integrated by high-order Godunov schemes for both the gas and particle phases. Numerical simulations of the explosion fields from 1.5-g Shock-Dispersed-Fuel (SDF) charge in a 6.6 liter calorimeter were used to validate the combustion model. Then the model was applied to 10-kg Al-SDF explosions in a vented two-room structure and in an unconfined height-of-burst explosion. Computed pressure histories are in reasonable (but not perfect) agreement with measured waveforms. Differences are caused by physical-chemical kinetic effects of particle combustion which induce ignition delays in the initial reactive blast wave and quenching of reactions at late times. Current simulations give initial insights into such modeling issues.« less

El Niño and coral larval dispersal across the eastern Pacific marine barrier

NASA Astrophysics Data System (ADS)

Wood, S.; Baums, I. B.; Paris, C. B.; Ridgwell, A.; Kessler, W. S.; Hendy, E. J.

2016-08-01

More than 5,000 km separates the frequently disturbed coral reefs of the Eastern Tropical Pacific (ETP) from western sources of population replenishment. It has been hypothesized that El Niño events facilitate eastward dispersal across this East Pacific Barrier (EPB). Here we present a biophysical coral larval dispersal model driven by 14.5 years of high-resolution surface ocean current data including the extreme 1997-1998 El Niño. We find no eastward cross-EPB connections over this period, which implies that ETP coral populations decimated by the 1998 bleaching event can only have recovered from eastern Pacific sources, in congruence with genetic data. Instead, rare connections between eastern and central Pacific reefs are simulated in a westward direction. Significant complexity and variability in the surface flows transporting larvae mean that generalized upper-ocean circulation patterns are poor descriptors of inter-regional connectivity, complicating the assessment of how climate change will impact coral gene flow Pacific wide.

El Niño and coral larval dispersal across the eastern Pacific marine barrier

PubMed Central

Wood, S.; Baums, I. B.; Paris, C. B.; Ridgwell, A.; Kessler, W. S.; Hendy, E. J.

2016-01-01

More than 5,000 km separates the frequently disturbed coral reefs of the Eastern Tropical Pacific (ETP) from western sources of population replenishment. It has been hypothesized that El Niño events facilitate eastward dispersal across this East Pacific Barrier (EPB). Here we present a biophysical coral larval dispersal model driven by 14.5 years of high-resolution surface ocean current data including the extreme 1997–1998 El Niño. We find no eastward cross-EPB connections over this period, which implies that ETP coral populations decimated by the 1998 bleaching event can only have recovered from eastern Pacific sources, in congruence with genetic data. Instead, rare connections between eastern and central Pacific reefs are simulated in a westward direction. Significant complexity and variability in the surface flows transporting larvae mean that generalized upper-ocean circulation patterns are poor descriptors of inter-regional connectivity, complicating the assessment of how climate change will impact coral gene flow Pacific wide. PMID:27550393

CMOS compatible on-chip telecom-band to mid-infrared supercontinuum generation in dispersion-engineered reverse strip/slot hybrid Si3N4 waveguide

NASA Astrophysics Data System (ADS)

Hui, Zhanqiang; Zhang, Lingxuan; Zhang, Wenfu

2018-01-01

A silicon nitride (Si3N4)-based reverse strip/slot hybrid waveguide with single vertical silica slot is proposed to acquire extremely low and flat chromatic dispersion profile. This is achieved by design and optimization of the geometrical structural parameters of the reverse hybrid waveguide. The flat dispersion varying between ±10 ps/(nm.km) is obtained over 610 nm bandwidth. Both the effective area and nonlinear coefficient of the waveguide across the entire spectral range of interest are investigated. This led to design of an on-chip supercontinuum (SC) source with -30 dB bandwidth of 2996 nm covering from 1.209 to 4.205 μm. Furthermore, we discuss the output signal spectral and temporal characteristic as a function of the pump power. Our waveguide design offers a CMOS compatible, low-cost/high yield (no photolithography or lift-off processes are necessary) on-chip SC source for near- and mid-infrared nonlinear applications.