Fixed-flexion knee radiography using a new positioning device produced highly repeatable measurements of joint space width: ELSA-Brasil Musculoskeletal Study (ELSA-Brasil MSK).

PubMed

Telles, Rosa Weiss; Costa-Silva, Luciana; Machado, Luciana A C; Reis, Rodrigo Citton Padilha Dos; Barreto, Sandhi Maria

To describe the performance of a non-fluoroscopic fixed-flexion PA radiographic protocol with a new positioning device, developed for the assessment of knee osteoarthritis (OA) in Brazilian Longitudinal Study of Adult Health Musculoskeletal Study (ELSA-Brasil MSK). A test-retest design including 19 adults (38 knee images) was conducted. Feasibility of the radiographic protocol was assessed by image quality parameters and presence of radioanatomic alignment according to intermargin distance (IMD) values. Repeatability was assessed for IMD and joint space width (JSW) measured at three different locations. Approximately 90% of knee images presented excellent quality. Frequencies of nearly perfect radioanatomic alignment (IMD ≤1mm) ranged from 29% to 50%, and satisfactory alignment was found in up to 71% and 76% of the images (IMD ≤1.5mm and ≤1.7mm, respectively). Repeatability analyses yielded the following results: IMD [SD of mean difference=1.08; coefficient of variation (%CV)=54.68%; intraclass correlation coefficient (ICC) (95%CI)=0.59 (0.34-0.77)]; JSW [SD of mean difference=0.34-0.61; %CV=4.48%-9.80%; ICC (95%CI)=0.74 (0.55-0.85)-0.94 (0.87-0.97)]. Adequately reproducible measurements of IMD and JSW were found in 68% and 87% of the images, respectively. Despite the difficulty in achieving consistent radioanatomic alignment between subsequent radiographs in terms of IMD, the protocol produced highly repeatable JSW measurements when these were taken at midpoint and 10mm from the medial extremity of the medial tibial plateau. Therefore, measurements of JSW at these locations can be considered adequate for the assessment of knee OA in ELSA-Brasil MSK. Copyright © 2016. Published by Elsevier Editora Ltda.

Measuring polyethylene wear in total knee arthroplasty by RSA: differences between weight-bearing and non-weight-bearing positioning.

PubMed

van Ijsseldijk, Emiel A; Valstar, Edward R; Stoel, Berend C; de Ridder, Ruud; Nelissen, Rob G H H; Kaptein, Bart L

2014-04-01

Measuring the minimum-joint-space-width (mJSW) in total knee arthroplasty (TKA) in Roentgen stereophotogrammetric analysis (RSA) provides valuable information on polyethylene wear, a leading cause for TKA failure. Most existing studies use non-weight-bearing (NWB) patient positioning. The latter may compromise mJSW measurements due to knee laxity with subsequent non-contact between the TKA components. We investigated the difference in mJSW between weight-bearing (WB) and NWB images and the association with mediolateral (ML) knee stability. At one-year follow-up, 23 TKAs were included from an ongoing RSA study, and ML stability was evaluated. For each examination, the mJSW and femoral-tibial contact locations were measured. A linear regression model was used to analyze the association between the mJSW difference (NWB-WB) with the ML stability and contact locations. The mean mJSW difference was 0.28 mm medially and 0.20 mm laterally. Four TKAs had medium (5-9°) and 19 TKAs had high (<5°) ML stability. A higher mJSW difference was found for TKAs with medium stability (0.36 mm, P = 0.01). In conclusion, mJSW measurements in existing (NWB) RSA studies are influenced by knee laxity, but may still provide information on wear progression based on TKA with high ML stability. A direct comparison of mJSW measurements from WB and NWB data is not possible. © 2014 Orthopaedic Research Society. Published by Wiley Periodicals, Inc.

Association of occupational activity with joint space narrowing and osteophytosis in the medial compartment of the knee: the ROAD study (OAC5914R2).

PubMed

Muraki, S; Oka, H; Akune, T; En-yo, Y; Yoshida, M; Nakamura, K; Kawaguchi, H; Yoshimura, N

2011-07-01

We investigated the association of occupational activity with joint space narrowing and osteophytosis at the knee separately in Japanese subjects using a large-scale population-based cohort of the Research on Osteoarthritis Against Disability (ROAD). From the baseline survey of the ROAD study, 1,402 participants (512 men and 890 women) living in mountainous and seacoast communities were analyzed. Information collected included a lifetime occupational history and details of specific workplace physical activities. To estimate the severity of joint space narrowing and osteophytosis at the knee, minimum joint space width (mJSW) and osteophyte area (OPA) in the medial compartment of the knee were measured using a knee osteoarthritis (OA) computer-aided diagnosis system. For women, agricultural, forestry, and fishery workers had significantly lower mJSW values compared with clerical workers or technical experts, whereas OPA did not differ significantly among job titles in men or women. For occupational activities, kneeling and squatting were associated with lower mJSW as well as higher OPA. Walking and heavy lifting were associated with lower mJSW, but not with OPA. This cross-sectional study using a population-based cohort suggests that an occupational activity that includes kneeling and squatting appears to have a greater effect on knee OA. Copyright © 2011 Osteoarthritis Research Society International. Published by Elsevier Ltd. All rights reserved.

Laterality of radiographic osteoarthritis of the knee.

PubMed

Komatsu, Daigo; Ikeuchi, Kazuma; Kojima, Toshihisa; Takegami, Yasuhiko; Amano, Takafumi; Tsuboi, Masaki; Ishiguro, Naoki; Hasegawa, Yukiharu

2017-05-01

There are few reports of the laterality in radiological knee osteoarthritis (ROA). This study aimed to evaluate laterality in terms of the minimum joint space width (mJSW) and osteophyte areas (OFs) in a cross-sectorial general population screen and elucidate the association between laterality and risk of osteoarthritis. We enrolled 330 participants (mean age 64.6 years) and examined the presence of ROA (Kellgren-Lawrence grade ≧ 2) laterality in terms of the mJSW and OF on the medial tibia using auto-measuring software. Moreover, we examined the association between laterality and leg dominance. The right and left medial mJSWs were 4.02 ± 0.98 mm and 4.05 ± 1.01 mm, respectively, showing no laterality; the laterals were also similar. The participants who had osteophytes ≥1 mm 2 in the right, left, and bilateral knees were 15, 37, and 57 respectively, with osteophytes being significantly more common in the left knee. The OF was significantly larger in the left knee. Conversely, the medial and lateral mJSWs and OF did not differ according to leg dominance. The prevalence of ROA was higher and the OF was more pronounced in the left knee. However, the mJSW showed no laterality. Additionally, the mJSW and OF showed no differences according to leg dominance.

Randomised, controlled trial of avocado-soybean unsaponifiable (Piascledine) effect on structure modification in hip osteoarthritis: the ERADIAS study.

PubMed

Maheu, Emmanuel; Cadet, Christian; Marty, Marc; Moyse, Dominique; Kerloch, Isabelle; Coste, Philippe; Dougados, Maxime; Mazières, Bernard; Spector, Tim D; Halhol, Hafid; Grouin, Jean-Marie; Lequesne, Michel

2014-02-01

To assess the ability of avocado-soybean unsaponifiable-Expanscience (ASU-E) to slow radiographic progression in symptomatic hip osteoarthritis (OA). Prospective, randomised, double blind, parallel group, placebo controlled 3 year trial. Patients with symptomatic (painful ≥1 year, Lequesne Index between 3 and 10) hip OA (American College of Rheumatology criteria) and a minimum joint space width (JSW) of the target hip between 1 and 4 mm on a pelvic radiograph were randomly assigned to 300 mg/day ASU-E or placebo. Standing pelvis, target hip anteroposterior (AP) and oblique views were taken annually. The primary outcome was JSW change at year 3, measured at the narrowest point on pelvic or target hip AP view (manual measure using a 0.1 mm graduated magnifying glass). The full analysis dataset (FAS) included all patients having at least two successive radiographs. An analysis of covariance Mixed Model for Repeated Measurements with Missing at Random (for missing data) was performed to compare adjusted 3 year JSW changes (primary outcome) and the percentages of 'progressors' (JSW loss≥0.5 mm) between groups. 399 patients were randomised (345 kept in the FAS), aged 62 (35-84) years, 54% women, mean body mass index 27 (SD 4) kg/m(2), mean symptom duration 4 (SD 5) years, 0-100 normalised Lequesne Index 30 (SD 9) and global pain visual analogue scale 37 (SD 23) mm. Mean baseline JSW was 2.8 (0.9) mm. There was no significant difference on mean JSW loss (-0.638 mm vs -0.672 mm, p=0.72, in the ASU-E and placebo groups, respectively) but there were 20% less progressors in the ASU-E than in the placebo group (40% vs 50%, respectively, p=0.040). No difference was observed on clinical outcomes. Safety was excellent. 3 year treatment with ASU-E reduces the percentage of JSW progressors, indicating a potential structure modifying effect in hip OA to be confirmed, and the clinical relevance requires further assessment.

Prediction of cartilaginous tissue repair after knee joint distraction.

PubMed

van der Woude, J A D; Welsing, P M; van Roermund, P M; Custers, R J H; Kuchuk, N O; Lafeber, F P J G G

2016-10-01

For young patients (<65years), knee joint distraction (KJD) may be a joint-saving treatment option for end-stage knee osteoarthritis. Distracting the femur from the tibia by five millimeters for six to eight weeks using an external fixation frame results in cartilaginous tissue repair, in addition to clinical benefits. This study is a first attempt to predict the degree of cartilaginous tissue repair after KJD. Fifty-seven consecutive patients received KJD. At baseline and at one year of follow-up, mean and minimum joint space width (JSW) of the most-affected compartment was determined on standardized radiographs. To evaluate the predictive ability of baseline characteristics for JSW at one year of follow-up, multivariable linear regression analysis was performed. Mean JSW±SD of the most affected compartment increased by 0.95±1.23mm to 3.08±1.43mm at one year (P<0.001). The minimum JSW increased by 0.94±1.03mm to 1.63±1.21mm at one year of follow-up (P<0.001). For a larger mean JSW one year after KJD, only Kellgren & Lawrence grade (KLG) at baseline was predictive (Regression coefficient (β)=0.47, 95% CI=0.18 to 0.77, P=0.002). For a larger minimum JSW, KLG (β=0.46, 95% CI=0.19 to 0.73, P=0.001) and male gender (β=0.52, 95% CI=0.06 to 0.99, P=0.028) were statistically predictive. Eight weeks of distraction time neared significance (β=0.44, 95% CI=-0.05 to 0.93, P=0.080). In our cohort of patients treated with KJD, males with higher KLG had the best chance of cartilaginous tissue repair by distraction. Copyright © 2016 Elsevier B.V. All rights reserved.

Is coxa valga a predictor for the severity of knee osteoarthritis? A cross-sectional study.

PubMed

Coskun Benlidayi, Ilke; Guzel, Rengin; Basaran, Sibel; Aksungur, Erol H; Seydaoglu, Gulsah

2015-05-01

In the present study, we aimed to evaluate the affect of the variations in hip anatomy and pelvic geometry on the severity of knee OA. Idiopathic knee OA patients fulfilling the clinical criteria of American College of Rheumatology for OA were enrolled in the study. Several measurements regarding the hip and pelvis were performed on pelvic radiographs. Each knee was graded according to the Kellgren and Lawrence (KL) radiographic system (0-4) along with a categorization in accordance with the medial tibiofemoral joint space widths (JSW). The study group consisted of 111 subjects. The inner and outer pelvic diameters were getting wider as the JSW grade increased. Likewise, among the hip measurements, femoral head, neck and shaft diameters and hip axis lengths were linked with KL grade. There were significant differences in neck-shaft angle (NSA) between groups of JSW with a highest NSA in JSW grade 3. The optimal cut-off value for NSA in predicting the severity of knee OA was 134.4°. Furthermore, NSA beyond 134.4° was found to increase the risk of severe knee OA eightfold. Variations in pelvic geometry and hip anatomy are associated with the severity of knee OA. People with NSA of above 134.4° have eightfold increased risk of developing severe knee OA. Pelvic radiographies could be evaluated at younger ages-particularly in people with high genetic predispositions-to identify the individuals at high risk and in turn, to tailor the preventive measures to these subjects.

Accurate joint space quantification in knee osteoarthritis: a digital x-ray tomosynthesis phantom study

NASA Astrophysics Data System (ADS)

Sewell, Tanzania S.; Piacsek, Kelly L.; Heckel, Beth A.; Sabol, John M.

2011-03-01

The current imaging standard for diagnosis and monitoring of knee osteoarthritis (OA) is projection radiography. However radiographs may be insensitive to markers of early disease such as osteophytes and joint space narrowing (JSN). Relative to standard radiography, digital X-ray tomosynthesis (DTS) may provide improved visualization of the markers of knee OA without the interference of superimposed anatomy. DTS utilizes a series of low-dose projection images over an arc of +/-20 degrees to reconstruct tomographic images parallel to the detector. We propose that DTS can increase accuracy and precision in JSN quantification. The geometric accuracy of DTS was characterized by quantifying joint space width (JSW) as a function of knee flexion and position using physical and anthropomorphic phantoms. Using a commercially available digital X-ray system, projection and DTS images were acquired for a Lucite rod phantom with known gaps at various source-object-distances, and angles of flexion. Gap width, representative of JSW, was measured using a validated algorithm. Over an object-to-detector-distance range of 5-21cm, a 3.0mm gap width was reproducibly measured in the DTS images, independent of magnification. A simulated 0.50mm (+/-0.13) JSN was quantified accurately (95% CI 0.44-0.56mm) in the DTS images. Angling the rods to represent knee flexion, the minimum gap could be precisely determined from the DTS images and was independent of flexion angle. JSN quantification using DTS was insensitive to distance from patient barrier and flexion angle. Potential exists for the optimization of DTS for accurate radiographic quantification of knee OA independent of patient positioning.

Knee joint distraction compared with high tibial osteotomy: a randomized controlled trial.

PubMed

van der Woude, J A D; Wiegant, K; van Heerwaarden, R J; Spruijt, S; van Roermund, P M; Custers, R J H; Mastbergen, S C; Lafeber, F P J G

2017-03-01

Both, knee joint distraction as a relatively new approach and valgus-producing opening-wedge high tibial osteotomy (HTO), are knee-preserving treatments for knee osteoarthritis (OA). The efficacy of knee joint distraction compared to HTO has not been reported. Sixty-nine patients with medial knee joint OA with a varus axis deviation of <10° were randomized to either knee joint distraction (n = 23) or HTO (n = 46). Questionnaires were assessed at baseline and 3, 6, and 12 months. Joint space width (JSW) as a surrogate measure for cartilage thickness was determined on standardized semi-flexed radiographs at baseline and 1-year follow-up. All patient-reported outcome measures (PROMS) improved significantly over 1 year (at 1 year p < 0.02) in both groups. At 1 year, the HTO group showed slightly greater improvement in 4 of the 16 PROMS (p < 0.05). The minimum medial compartment JSW increased 0.8 ± 1.0 mm in the knee joint distraction group (p = 0.001) and 0.4 ± 0.5 mm in the HTO group (p < 0.001), with minimum JSW improvement in favour of knee joint distraction (p = 0.05). The lateral compartment showed a small increase in the knee joint distraction group and a small decrease in the HTO group, leading to a significant increase in mean JSW for knee joint distraction only (p < 0.02). Cartilaginous repair activity, as indicated by JSW, and clinical outcome improvement occurred with both, knee joint distraction and HTO. These findings suggest that knee joint distraction may be an alternative therapy for medial compartmental OA with a limited mechanical leg malalignment. Randomized controlled trial, Level I.

Knee Images Digital Analysis (KIDA): a novel method to quantify individual radiographic features of knee osteoarthritis in detail.

PubMed

Marijnissen, A C A; Vincken, K L; Vos, P A J M; Saris, D B F; Viergever, M A; Bijlsma, J W J; Bartels, L W; Lafeber, F P J G

2008-02-01

Radiography is still the golden standard for imaging features of osteoarthritis (OA), such as joint space narrowing, subchondral sclerosis, and osteophyte formation. Objective assessment, however, remains difficult. The goal of the present study was to evaluate a novel digital method to analyse standard knee radiographs. Standardized radiographs of 20 healthy and 55 OA knees were taken in general practise according to the semi-flexed method by Buckland-Wright. Joint Space Width (JSW), osteophyte area, subchondral bone density, joint angle, and tibial eminence height were measured as continuous variables using newly developed Knee Images Digital Analysis (KIDA) software on a standard PC. Two observers evaluated the radiographs twice, each on two different occasions. The observers were blinded to the source of the radiographs and to their previous measurements. Statistical analysis to compare measurements within and between observers was performed according to Bland and Altman. Correlations between KIDA data and Kellgren & Lawrence (K&L) grade were calculated and data of healthy knees were compared to those of OA knees. Intra- and inter-observer variations for measurement of JSW, subchondral bone density, osteophytes, tibial eminence, and joint angle were small. Significant correlations were found between KIDA parameters and K&L grade. Furthermore, significant differences were found between healthy and OA knees. In addition to JSW measurement, objective evaluation of osteophyte formation and subchondral bone density is possible on standard radiographs. The measured differences between OA and healthy individuals suggest that KIDA allows detection of changes in time, although sensitivity to change has to be demonstrated in long-term follow-up studies.

Validity of radiographic assessment of the knee joint space using automatic image analysis.

PubMed

Komatsu, Daigo; Hasegawa, Yukiharu; Kojima, Toshihisa; Seki, Taisuke; Ikeuchi, Kazuma; Takegami, Yasuhiko; Amano, Takafumi; Higuchi, Yoshitoshi; Kasai, Takehiro; Ishiguro, Naoki

2016-09-01

The present study investigated whether there were differences between automatic and manual measurements of the minimum joint space width (mJSW) on knee radiographs. Knee radiographs of 324 participants in a systematic health screening were analyzed using the following three methods: manual measurement of film-based radiographs (Manual), manual measurement of digitized radiographs (Digital), and automatic measurement of digitized radiographs (Auto). The mean mJSWs on the medial and lateral sides of the knees were determined using each method, and measurement reliability was evaluated using intra-class correlation coefficients. Measurement errors were compared between normal knees and knees with radiographic osteoarthritis. All three methods demonstrated good reliability, although the reliability was slightly lower with the Manual method than with the other methods. On the medial and lateral sides of the knees, the mJSWs were the largest in the Manual method and the smallest in the Auto method. The measurement errors of each method were significantly larger for normal knees than for radiographic osteoarthritis knees. The mJSW measurements are more accurate and reliable with the Auto method than with the Manual or Digital method, especially for normal knees. Therefore, the Auto method is ideal for the assessment of the knee joint space.

OARSI-OMERACT definition of relevant radiological progression in hip/knee osteoarthritis.

PubMed

Ornetti, P; Brandt, K; Hellio-Le Graverand, M-P; Hochberg, M; Hunter, D J; Kloppenburg, M; Lane, N; Maillefert, J-F; Mazzuca, S A; Spector, T; Utard-Wlerick, G; Vignon, E; Dougados, M

2009-07-01

Joint space width (JSW) evaluated in millimeters on plain X-rays is the currently optimal recognized technique to evaluate osteoarthritis (OA) structural progression. Data obtained can be presented at the group level (e.g., mean+/-standard deviation of the changes). Such presentation makes difficult the interpretation of the clinical relevance of the reported results. Therefore, a presentation at the individual level (e.g., % progressors) seems more attractive but requires to determining a cut-off. Several methodologies have been proposed to define cut-offs in JSW: arbitrary chosen cut-off, cut-off based on the validity to predict a relevant end-point such as the requirement of total articular replacement or cut-off based on the measurement error such as smallest detectable difference (SDD). The objective of this OARSI-OMERACT initiative was to define a cut-off evaluated in millimeters on plain X-rays above which a change in JSW could be considered as relevant in patients with hip and knee OA. The first step consisted in a systematic literature research performed using Medline database up to July 2007 to obtain all manuscripts published between 1990 and 2007 reporting a cut-off value in JSW evaluated in millimeters at either the knee or hip level. The second step consisted in a consensus based on the best knowledge of the 11 experts with the support of the available evidence. Among the 506 articles selected by the search, 47 articles reported cut-off of JSW in millimeters. There was a broad heterogeneity in cut-off values, whatever the methodologies or the OA localization considered (e.g., from 0.12 to 0.84 mm and from 0.22 to 0.78 mm for Knee (seven studies) and hip (seven studies), respectively when considering the data obtained based on the reliability). Based on the data extracted in the literature, the expert committee proposed a definition of relevant change in JSW based on plain X-rays, on an absolute change of JSW in millimeters and on the measurement error e.g., calculation of the SDD using the Bland and Altman technique. The results of the analysis of JSW should be expressed in terms of a dichotomous variable (e.g., progressors yes/no): a patient with a change in JSW during the study over such SDD will fulfill the definition of "progressor". Moreover, the pilot study aimed at evaluating the measurement error should be designed to reflect the different characteristics of the primary study in which the analysis of the radiological findings will be based on (patient's characteristics, centers characteristics, readers). This initiative based on both an Evidence Based Medicine (Systematic Literature Research) and Expert Opinion approach resulted in a proposal of definition of relevant radiological progression in OA to be used as end-point in clinical trials and also recommendations on the conduct of the reliability study allowing such definition.

Validation of automatic joint space width measurements in hand radiographs in rheumatoid arthritis.

PubMed

Schenk, Olga; Huo, Yinghe; Vincken, Koen L; van de Laar, Mart A; Kuper, Ina H H; Slump, Kees C H; Lafeber, Floris P J G; Bernelot Moens, Hein J

2016-10-01

Computerized methods promise quick, objective, and sensitive tools to quantify progression of radiological damage in rheumatoid arthritis (RA). Measurement of joint space width (JSW) in finger and wrist joints with these systems performed comparable to the Sharp-van der Heijde score (SHS). A next step toward clinical use, validation of precision and accuracy in hand joints with minimal damage, is described with a close scrutiny of sources of error. A recently developed system to measure metacarpophalangeal (MCP) and proximal interphalangeal (PIP) joints was validated in consecutive hand images of RA patients. To assess the impact of image acquisition, measurements on radiographs from a multicenter trial and from a recent prospective cohort in a single hospital were compared. Precision of the system was tested by comparing the joint space in mm in pairs of subsequent images with a short interval without progression of SHS. In case of incorrect measurements, the source of error was analyzed with a review by human experts. Accuracy was assessed by comparison with reported measurements with other systems. In the two series of radiographs, the system could automatically locate and measure 1003/1088 (92.2%) and 1143/1200 (95.3%) individual joints, respectively. In joints with a normal SHS, the average (SD) size of MCP joints was [Formula: see text] and [Formula: see text] in the two series of radiographs, and of PIP joints [Formula: see text] and [Formula: see text]. The difference in JSW between two serial radiographs with an interval of 6 to 12 months and unchanged SHS was [Formula: see text], indicating very good precision. Errors occurred more often in radiographs from the multicenter cohort than in a more recent series from a single hospital. Detailed analysis of the 55/1125 (4.9%) measurements that had a discrepant paired measurement revealed that variation in the process of image acquisition (exposure in 15% and repositioning in 57%) was a more frequent source of error than incorrect delineation by the software (25%). Various steps in the validation of an automated measurement system for JSW of MCP and PIP joints are described. The use of serial radiographs from different sources, with a short interval and limited damage, is helpful to detect sources of error. Image acquisition, in particular repositioning, is a dominant source of error.

Semiautomated digital analysis of knee joint space width using MR images.

PubMed

Agnesi, Filippo; Amrami, Kimberly K; Frigo, Carlo A; Kaufman, Kenton R

2007-05-01

The goal of this study was to (a) develop a semiautomated computer algorithm to measure knee joint space width (JSW) from magnetic resonance (MR) images using standard imaging techniques and (b) evaluate the reproducibility of the algorithm. Using a standard clinical imaging protocol, bilateral knee MR images were obtained twice within a 2-week period from 17 asymptomatic research participants. Images were analyzed to determine the variability of the measurements performed by the program compared with the variability of manual measurements. Measurement variability of the computer algorithm was considerably smaller than the variability of manual measurements. The average difference between two measurements of the same slice performed with the computer algorithm by the same user was 0.004 +/- 0.07 mm for the tibiofemoral joint (TF) and 0.009 +/- 0.11 mm for the patellofemoral joint (PF) compared with an average of 0.12 +/- 0.22 mm TF and 0.13 +/- 0.29 mm PF, respectively, for the manual method. Interuser variability of the computer algorithm was also considerably smaller, with an average difference of 0.004 +/- 0.1 mm TF and 0.0006 +/- 0.1 mm PF compared with 0.38 +/- 0.59 mm TF and 0.31 +/- 0.66 mm PF obtained using a manual method. The between-day reproducibility was larger but still within acceptable limits at 0.09 +/- 0.39 mm TF and 0.09 +/- 0.51 mm PF. This technique has proven consistently reproducible on a same slice base,while the reproducibility comparing different acquisitions of the same subject was larger. Longitudinal reproducibility improvement needs to be addressed through acquisition protocol improvements. A semiautomated method for measuring knee JSW from MR images has been successfully developed.

Validation of automatic joint space width measurements in hand radiographs in rheumatoid arthritis

PubMed Central

Schenk, Olga; Huo, Yinghe; Vincken, Koen L.; van de Laar, Mart A.; Kuper, Ina H. H.; Slump, Kees C. H.; Lafeber, Floris P. J. G.; Bernelot Moens, Hein J.

2016-01-01

Abstract. Computerized methods promise quick, objective, and sensitive tools to quantify progression of radiological damage in rheumatoid arthritis (RA). Measurement of joint space width (JSW) in finger and wrist joints with these systems performed comparable to the Sharp–van der Heijde score (SHS). A next step toward clinical use, validation of precision and accuracy in hand joints with minimal damage, is described with a close scrutiny of sources of error. A recently developed system to measure metacarpophalangeal (MCP) and proximal interphalangeal (PIP) joints was validated in consecutive hand images of RA patients. To assess the impact of image acquisition, measurements on radiographs from a multicenter trial and from a recent prospective cohort in a single hospital were compared. Precision of the system was tested by comparing the joint space in mm in pairs of subsequent images with a short interval without progression of SHS. In case of incorrect measurements, the source of error was analyzed with a review by human experts. Accuracy was assessed by comparison with reported measurements with other systems. In the two series of radiographs, the system could automatically locate and measure 1003/1088 (92.2%) and 1143/1200 (95.3%) individual joints, respectively. In joints with a normal SHS, the average (SD) size of MCP joints was 1.7±0.2 and 1.6±0.3  mm in the two series of radiographs, and of PIP joints 1.0±0.2 and 0.9±0.2  mm. The difference in JSW between two serial radiographs with an interval of 6 to 12 months and unchanged SHS was 0.0±0.1  mm, indicating very good precision. Errors occurred more often in radiographs from the multicenter cohort than in a more recent series from a single hospital. Detailed analysis of the 55/1125 (4.9%) measurements that had a discrepant paired measurement revealed that variation in the process of image acquisition (exposure in 15% and repositioning in 57%) was a more frequent source of error than incorrect delineation by the software (25%). Various steps in the validation of an automated measurement system for JSW of MCP and PIP joints are described. The use of serial radiographs from different sources, with a short interval and limited damage, is helpful to detect sources of error. Image acquisition, in particular repositioning, is a dominant source of error. PMID:27921071

Digital tomosynthesis rendering of joint margins for arthritis assessment

NASA Astrophysics Data System (ADS)

Duryea, Jeffrey W.; Neumann, Gesa; Yoshioka, Hiroshi; Dobbins, James T., III

2004-05-01

PURPOSE: Rheumatoid arthritis (RA) of the hand is a significant healthcare problem. Techniques to accurately quantity the structural changes from RA are crucial for the development and prescription of therapies. Analysis of radiographic joint space width (JSW) is widely used and has demonstrated promise. However, radiography presents a 2D view of the joint. In this study we performed tomosynthesis reconstructions of proximal interphalangeal (PIP), and metacarpophalangeal (MCP) joints to measure the 3D joint structure. METHODS: We performed a reader study using simulated radiographs of 12 MCP and 12 PIP joints from skeletal specimens imaged with micro-CT. The tomosynthesis technique provided images of reconstructed planes with 0.75 mm spacing, which were presented to 2 readers with a computer tool. The readers were instructed to delineate the joint surfaces on tomosynthetic slices where they could visualize the margins. We performed a quantitative analysis of 5 slices surrounding the central portion of each joint. Reader-determined JSW was compared to a gold standard. As a figure of merit we calculated the average root-mean square deviation (RMSD). RESULTS: RMSD was 0.22 mm for both joints. For the individual joints, RMSD was 0.18 mm (MCP), and 0.26 mm (PIP). The reduced performance for the smaller PIP joints suggests that a slice spacing less than 0.75 mm may be more appropriate. CONCLUSIONS: We have demonstrated the capability of limited 3D rendering of joint surfaces using digital tomosynthesis. This technique promises to provide an improved method to visualize the structural changes of RA.

Five-Year Follow-up of Knee Joint Distraction: Clinical Benefit and Cartilaginous Tissue Repair in an Open Uncontrolled Prospective Study.

PubMed

van der Woude, Jan-Ton A D; Wiegant, Karen; van Roermund, Peter M; Intema, Femke; Custers, Roel J H; Eckstein, Felix; van Laar, Jaap M; Mastbergen, Simon C; Lafeber, Floris P J G

2017-07-01

Objective In end-stage knee osteoarthritis, total knee arthroplasty (TKA) may finally become inevitable. At a relatively young age, this comes with the risk of future revision surgery. Therefore, in these cases, joint preserving surgery such as knee joint distraction (KJD) is preferred. Here we present 5-year follow-up data of KJD. Design Patients ( n = 20; age <60 years) with conservative therapy resistant tibiofemoral osteoarthritis considered for TKA were treated. Clinical evaluation was performed by questionnaires. Change in cartilage thickness was quantified on radiographs and magnetic resonance images (MRI). The 5-year changes after KJD were evaluated and compared with the natural progression of osteoarthritis using Osteoarthritis Initiative data. Results Five-years posttreatment, patients still reported clinical improvement from baseline: ΔWOMAC (Western Ontario and McMaster Universities Arthritis Index) +21.1 points (95% CI +8.9 to +33.3; P = 0.002), ΔVAS (visual analogue scale score) pain -27.6 mm (95%CI -13.3 to -42.0; P < 0.001), and minimum radiographic joint space width (JSW) of the most affected compartment (MAC) remained increased as well: Δ +0.43 mm (95% CI +0.02 to +0.84; P = 0.040). Improvement of mean JSW (x-ray) and mean cartilage thickness (MRI) of the MAC, were not statistically different from baseline anymore (Δ +0.26 mm; P = 0.370, and Δ +0.23 mm; P = 0.177). Multivariable linear regression analysis indicated that KJD treatment was associated with significantly less progression in mean and min JSW (x-ray) and mean cartilage thickness (MRI) compared with natural progression (all Ps <0.001). Conclusions KJD treatment results in prolonged clinical benefit, potentially explained by an initial boost of cartilaginous tissue repair that provides a long-term tissue structure benefit as compared to natural progression. Level of evidence, II.

Efficacy and safety of strontium ranelate in the treatment of knee osteoarthritis: results of a double-blind, randomised placebo-controlled trial

PubMed Central

Reginster, Jean-Yves; Badurski, Janusz; Bellamy, Nicholas; Bensen, William; Chapurlat, Roland; Chevalier, Xavier; Christiansen, Claus; Genant, Harry; Navarro, Federico; Nasonov, Evgeny; Sambrook, Philip N; Spector, Timothy D; Cooper, Cyrus

2013-01-01

Background Strontium ranelate is currently used for osteoporosis. The international, double-blind, randomised, placebo-controlled Strontium ranelate Efficacy in Knee OsteoarthrItis triAl evaluated its effect on radiological progression of knee osteoarthritis. Methods Patients with knee osteoarthritis (Kellgren and Lawrence grade 2 or 3, and joint space width (JSW) 2.5–5 mm) were randomly allocated to strontium ranelate 1 g/day (n=558), 2 g/day (n=566) or placebo (n=559). The primary endpoint was radiographical change in JSW (medial tibiofemoral compartment) over 3 years versus placebo. Secondary endpoints included radiological progression, Western Ontario and McMaster Universities Osteoarthritis Index (WOMAC) score, and knee pain. The trial is registered (ISRCTN41323372). Results The intention-to-treat population included 1371 patients. Treatment with strontium ranelate was associated with smaller degradations in JSW than placebo (1 g/day: −0.23 (SD 0.56) mm; 2 g/day: −0.27 (SD 0.63) mm; placebo: −0.37 (SD 0.59) mm); treatment-placebo differences were 0.14 (SE 0.04), 95% CI 0.05 to 0.23, p<0.001 for 1 g/day and 0.10 (SE 0.04), 95% CI 0.02 to 0.19, p=0.018 for 2 g/day. Fewer radiological progressors were observed with strontium ranelate (p<0.001 and p=0.012 for 1 and 2 g/day). There were greater reductions in total WOMAC score (p=0.045), pain subscore (p=0.028), physical function subscore (p=0.099) and knee pain (p=0.065) with strontium ranelate 2 g/day. Strontium ranelate was well tolerated. Conclusions Treatment with strontium ranelate 1 and 2 g/day is associated with a significant effect on structure in patients with knee osteoarthritis, and a beneficial effect on symptoms for strontium ranelate 2 g/day. PMID:23117245

Multivariate Radiological-Based Models for the Prediction of Future Knee Pain: Data from the OAI

PubMed Central

Galván-Tejada, Jorge I.; Celaya-Padilla, José M.; Treviño, Victor; Tamez-Peña, José G.

2015-01-01

In this work, the potential of X-ray based multivariate prognostic models to predict the onset of chronic knee pain is presented. Using X-rays quantitative image assessments of joint-space-width (JSW) and paired semiquantitative central X-ray scores from the Osteoarthritis Initiative (OAI), a case-control study is presented. The pain assessments of the right knee at the baseline and the 60-month visits were used to screen for case/control subjects. Scores were analyzed at the time of pain incidence (T-0), the year prior incidence (T-1), and two years before pain incidence (T-2). Multivariate models were created by a cross validated elastic-net regularized generalized linear models feature selection tool. Univariate differences between cases and controls were reported by AUC, C-statistics, and ODDs ratios. Univariate analysis indicated that the medial osteophytes were significantly more prevalent in cases than controls: C-stat 0.62, 0.62, and 0.61, at T-0, T-1, and T-2, respectively. The multivariate JSW models significantly predicted pain: AUC = 0.695, 0.623, and 0.620, at T-0, T-1, and T-2, respectively. Semiquantitative multivariate models predicted paint with C-stat = 0.671, 0.648, and 0.645 at T-0, T-1, and T-2, respectively. Multivariate models derived from plain X-ray radiography assessments may be used to predict subjects that are at risk of developing knee pain. PMID:26504490

Six weeks of continuous joint distraction appears sufficient for clinical benefit and cartilaginous tissue repair in the treatment of knee osteoarthritis.

PubMed

van der Woude, J A D; van Heerwaarden, R J; Spruijt, S; Eckstein, F; Maschek, S; van Roermund, P M; Custers, R J H; van Spil, W E; Mastbergen, S C; Lafeber, F P J G

2016-10-01

Knee joint distraction (KJD) is a surgical joint-preserving treatment in which the knee joint is temporarily distracted by an external frame. It is associated with joint tissue repair and clinical improvement. Initially, patients were submitted to an eight-week distraction period, and currently patients are submitted to a six-week distraction period. This study evaluates whether a shorter distraction period influences the outcome. Both groups consisted of 20 patients. Clinical outcome was assessed by WOMAC questionnaires and VAS-pain. Cartilaginous tissue repair was assessed by radiographic joint space width (JSW) and MRI-observed cartilage thickness. Baseline data between both groups were comparable. Both groups showed an increase in total WOMAC score; 24±4 in the six-week group and 32±5 in the eight-week group (both p<0.001). Mean JSW increased 0.9±0.3mm in the six-week group and 1.1±0.3mm in the eight-week group (p=0.729 between groups). The increase in mean cartilage thickness on MRI was 0.6±0.2mm in the eight-week group and 0.4±0.1mm in the six-week group (p=0.277). A shorter distraction period does not influence short-term clinical and structural outcomes statistically significantly, although effect sizes tend to be smaller in six week KJD as compared to eight week KJD. Copyright © 2016 Elsevier B.V. All rights reserved.

Assessment of the radioanatomic positioning of the osteoarthritic knee in serial radiographs: comparison of three acquisition techniques.

PubMed

Le Graverand, M-P H; Mazzuca, S; Lassere, M; Guermazi, A; Pickering, E; Brandt, K; Peterfy, C; Cline, G; Nevitt, M; Woodworth, T; Conaghan, P; Vignon, E

2006-01-01

Recent studies using various standardized radiographic acquisition techniques have demonstrated the necessity of reproducible radioanatomic alignment of the knee to assure precise measurements of medial tibiofemoral joint space width (JSW). The objective of the present study was to characterize the longitudinal performance of several acquisition techniques with respect to long-term reproducibility of positioning of the knee, and the impact of changes in positioning on the rate and variability of joint space narrowing (JSN). Eighty subjects were randomly selected from each of three cohorts followed in recent studies of the radiographic progression of knee osteoarthritis (OA): the Health ABC study (paired fixed-flexion [FF] radiographs taken at a 36-month interval); the Glucosamine Arthritis Intervention Trial (GAIT) (paired metatarsophalangeal [MTP] radiographs obtained at a 12-month interval), and a randomized clinical trial of doxycycline (fluoroscopically assisted semiflexed anteroposterior (AP) radiographs taken at a 16-month interval). Manual measurements were obtained from each radiograph to represent markers of radioanatomic positioning of the knee (alignment of the medial tibial plateau and X-ray beam, knee rotation, femorotibial angle) and to evaluate minimum JSW (mJSW) in the medial tibiofemoral compartment. The effects on the mean annualized rate of JSN and on the variability of that rate of highly reproduced vs variable positioning of the knee in serial radiographs were evaluated. Parallel or near-parallel alignment was achieved significantly more frequently with the fluoroscopically guided positioning used in the semiflexed AP protocol than with either the non-fluoroscopic FF or MTP protocol (68% vs 14% for both FF and MTP protocols when measured at the midpoint of the medial compartment; 75% vs 26% and 34% for the FF and MTP protocols, respectively, when measured at the site of mJSW; P<0.001 for each). Knee rotation was reproduced more frequently in semiflexed AP radiographs than in FF radiographs (66% vs 45%, P<0.01). In contrast, the FF technique yielded a greater proportion of paired radiographs in which the femorotibial angle was accurately reproduced than the semiflexed AP or MTP protocol (78% vs 59% and 56%, respectively, P<0.01 for each). Notably, only paired radiographs with parallel or near-parallel alignment exhibited a mean rate of JSN (+/-SD) in the OA knee that was more rapid and less variable than that measured in all knees (0.186+/-0.274 mm/year, standardized response to mean [SRM]=0.68 vs 0.128+/-0.291 mm/year, SRM=0.44). This study confirms the importance of parallel radioanatomic alignment of the anterior and posterior margins of the medial tibial plateau in detecting JSN in subjects with knee OA. The use of radiographic methods that assure parallel alignment during serial X-ray examinations will permit the design of more efficient studies of biomarkers of OA progression and of structure modification in knee OA.

Knee joint distraction compared with total knee arthroplasty: a randomised controlled trial.

PubMed

van der Woude, J A D; Wiegant, K; van Heerwaarden, R J; Spruijt, S; Emans, P J; Mastbergen, S C; Lafeber, F P J G

2017-01-01

Knee joint distraction (KJD) is a relatively new, knee-joint preserving procedure with the goal of delaying total knee arthroplasty (TKA) in young and middle-aged patients. We present a randomised controlled trial comparing the two. The 60 patients ≤ 65 years with end-stage knee osteoarthritis were randomised to either KJD (n = 20) or TKA (n = 40). Outcomes were assessed at baseline, three, six, nine, and 12 months. In the KJD group, the joint space width (JSW) was radiologically assessed, representing a surrogate marker of cartilage thickness. In total 56 patients completed their allocated treatment (TKA = 36, KJD = 20). All patient reported outcome measures improved significantly over one year (p < 0.02) in both groups. At one year, the TKA group showed a greater improvement in only one of the 16 patient-related outcome measures assessed (p = 0.034). Outcome Measures in Rheumatology-Osteoarthritis Research Society International clinical response was 83% after TKA and 80% after KJD. A total of 12 patients (60%) in the KJD group sustained pin track infections. In the KJD group both mean minimum (0.9 mm, standard deviation (sd) 1.1) and mean JSW (1.2 mm, sd 1.1) increased significantly (p = 0.004 and p = 0.0003). In relatively young patients with end-stage knee osteoarthritis, KJD did not demonstrate inferiority of outcomes at one year when compared with TKA. However, there is a high incidence of pin track infection associated with KJD. Cite this article: Bone Joint J 2017;99-B:51-8. ©2017 The British Editorial Society of Bone & Joint Surgery.

Quantitative 3D analysis of bone in hip osteoarthritis using clinical computed tomography.

PubMed

Turmezei, Tom D; Treece, Graham M; Gee, Andrew H; Fotiadou, Anastasia F; Poole, Kenneth E S

2016-07-01

To assess the relationship between proximal femoral cortical bone thickness and radiological hip osteoarthritis using quantitative 3D analysis of clinical computed tomography (CT) data. Image analysis was performed on clinical CT imaging data from 203 female volunteers with a technique called cortical bone mapping (CBM). Colour thickness maps were created for each proximal femur. Statistical parametric mapping was performed to identify statistically significant differences in cortical bone thickness that corresponded with the severity of radiological hip osteoarthritis. Kellgren and Lawrence (K&L) grade, minimum joint space width (JSW) and a novel CT-based osteophyte score were also blindly assessed from the CT data. For each increase in K&L grade, cortical thickness increased by up to 25 % in distinct areas of the superolateral femoral head-neck junction and superior subchondral bone plate. For increasing severity of CT osteophytes, the increase in cortical thickness was more circumferential, involving a wider portion of the head-neck junction, with up to a 7 % increase in cortical thickness per increment in score. Results were not significant for minimum JSW. These findings indicate that quantitative 3D analysis of the proximal femur can identify changes in cortical bone thickness relevant to structural hip osteoarthritis. • CT is being increasingly used to assess bony involvement in osteoarthritis • CBM provides accurate and reliable quantitative analysis of cortical bone thickness • Cortical bone is thicker at the superior femoral head-neck with worse osteoarthritis • Regions of increased thickness co-locate with impingement and osteophyte formation • Quantitative 3D bone analysis could enable clinical disease prediction and therapy development.

Effects of glucosamine and chondroitin on treating knee osteoarthritis: an analysis with marginal structural models

PubMed Central

Yang, Shibing; Eaton, Charles B.; McAlindon, Timothy E.; Lapane, Kate L.

2014-01-01

Objective The purpose of this study was to estimate the effectiveness of glucosamine and chondroitin in relieving knee symptoms and slowing disease progression among patients with knee osteoarthritis (OA). Methods The 4-year follow-up data from Osteoarthritis Initiative were analyzed. We used a “new-user” design, for which only participants who were not using glucosamine/chondroitin at baseline were included in analyses (n=1,625). Cumulative exposure was calculated as the number of visits when participants reported use of glucosamine/chondroitin. Knee symptoms were measured with WOMAC scale and structural progression was measured with joint space width (JSW). To control for the time-varying confounders that might be influenced by prior treatments, we used marginal structural models to estimate the effects of using glucosamine/chondroitin for three years, two years and one year on treating OA. Results During the study period, 18% of the participants initiated treatment with glucosamine/chondroitin. After adjustment for potential confounders with marginal structural models, we found no clinically significant differences between users at all assessments and never-users of glucosamine/chondroitin in WOMAC Pain: 0.68 (95% CI: -0.16 to 1.53); WOMAC Stiffness: 0.41 (95% CI: 0 to 0.82); WOMAC Function: 1.28 (95% CI: -1.23 to 3.79); or JSW: 0.11 (95% CI: -0.21 to 0.44). Conclusions Use of glucosamine/chondroitin did not appear to relieve symptoms or modify disease progression among patients with radiographically confirmed OA. Our findings, which are consistent with meta-analyses of clinical trials, extend the results to a more general population with knee OA. PMID:25369761

Baseline and longitudinal change in isometric muscle strength prior to radiographic progression in osteoarthritic and pre-osteoarthritic knees--data from the Osteoarthritis Initiative.

PubMed

Eckstein, F; Hitzl, W; Duryea, J; Kent Kwoh, C; Wirth, W

2013-05-01

To test whether cross-sectional or longitudinal measures of thigh muscle isometric strength differ between knees with and without subsequent radiographic progression of knee osteoarthritis (KOA), with particular focus on pre-osteoarthritic female knees (knees with risk factors but without definite radiographic KOA). Of 4,796 Osteoarthritis Initiative participants, 2,835 knees with Kellgren Lawrence grade (KLG) 0-3 had central X-ray readings, annual quantitative joint space width (JSW) and isometric muscle strength measurements (Good strength chair). Separate slope analysis of covariance (ANCOVA) models were used to determine differences in strength between "progressor" and "non-progressor" knees, after adjusting for age, body mass index, and pain. 466 participant knees exceeded the smallest detectable JSW change during each of two observation intervals (year 2→4 and year 1→3) and were classified as progressors (213 women, 253 men; 128 KLG0/1, 330 KLG2/3); 946 participant knees did not exceed this threshold in either interval and were classified as non-progressors (588 women, 358 from men; 288KLG0/1, 658KLG2/3). Female progressor knees, including those with KLG0/1, tended to have lower extensor and flexor strength at year 2 and at baseline than those without progression, but the difference was not significant after adjusting for confounders. No significant difference was observed in longitudinal change of muscle strength (baseline→year 2) prior to radiographic progression. No significant differences were found for muscle strength in men, and none for change in strength concomitant with progression. This study provides no strong evidence that (changes in) isometric muscle strength precedes or is associated with structural (radiographic) progression of KOA. Copyright © 2013 Osteoarthritis Research Society International. Published by Elsevier Ltd. All rights reserved.

Baseline and Longitudinal Change in Isometric Muscle Strength Prior to Radiographic Progression in Osteoarthritic and Pre-Osteoarthritic Knees- Data from the Osteoarthritis Initiative

PubMed Central

Eckstein, Felix; Hitzl, Wolfgang; Duryea, Jeff; Kwoh, C. Kent; Wirth, Wolfgang

2013-01-01

OBJECTIVE To test whether cross-sectional or longitudinal measures of thigh muscle isometric strength differ between knees with and without subsequent radiographic progression of knee osteoarthritis (KOA), with particular focus on pre-osteoarthritic female knees (knees with risk factors but without definite radiographic KOA). METHODS Of 4796 Osteoarthritis Initiative participants, 2835 knees with Kellgren Lawrence grade (KLG) 0–3 had central X-ray readings, annual quantitative joint space width (JSW) and isometric muscle strength measurements (Good strength chair). Separate slope ANCOVA models were used to determine differences in strength between “progressor” and “non- progressor” knees, after adjusting for age, body mass index, and pain. RESULTS 466 participant knees exceeded the smallest detectable JSW change during each of two observation intervals (year 2→4 and year 1→3) and were classified as progressors (213 women, 253 men; 128 KLG0/1, 330 KLG2/3); 946 participant knees did not exceed this threshold in either interval and were classified as non-progressors (588 women, 358 from men; 288KLG0/1, 658KLG2/3). Female progressor knees, including those with KLG0/1, tended to have lower extensor and flexor strength at year2 and at baseline than those without progression, but the difference was not significant after adjusting for confounders. No significant difference was observed in longitudinal change of muscle strength (baseline→year2) prior to radiographic progression. No significant differences were found for muscle strength in men, and none for change in strength concomitant with progression. CONCLUSION This study provides no strong evidence that (changes in) isometric muscle strength precedes or is associated with structural (radiographic) progression of KOA. PMID:23473978

Tissue structure modification in knee osteoarthritis by use of joint distraction: an open 1-year pilot study

PubMed Central

Intema, Femke; Van Roermund, Peter M; Marijnissen, Anne C A; Cotofana, Sebastian; Eckstein, Felix; Castelein, Rene M; Bijlsma, Johannes W J; Mastbergen, Simon C; Lafeber, Floris P J G

2011-01-01

Background Modification of joint tissue damage is challenging in late-stage osteoarthritis (OA). Few options are available for treating end-stage knee OA other than joint replacement. Objectives To examine whether joint distraction can effectively modify knee joint tissue damage and has the potential to delay prosthesis surgery. Methods 20 patients (<60 years) with tibiofemoral OA were treated surgically using joint distraction. Distraction (∼5 mm) was applied for 2 months using an external fixation frame. Tissue structure modification at 1 year of follow-up was evaluated radiographically (joint space width (JSW)), by MRI (segmentation of cartilage morphology) and by biochemical markers of collagen type II turnover, with operators blinded to time points. Clinical improvement was evaluated by Western Ontario and McMaster Universities Osteoarthritis Index (WOMAC) and Visual Analogue Scale (VAS) pain score. Results Radiography demonstrated an increase in mean and minimum JSW (2.7 to 3.6 mm and 1.0 to 1.9 mm; p<0.05 and <0.01). MRI revealed an increase in cartilage thickness (2.4 to 3.0 mm; p<0.001) and a decrease of denuded bone areas (22% to 5%; p<0.001). Collagen type II levels showed a trend towards increased synthesis (+103%; p<0.06) and decreased breakdown (−11%; p<0.08). The WOMAC index increased from 45 to 77 points, and VAS pain decreased from 73 to 31 mm (both p<0.001). Conclusions Joint distraction can induce tissue structure modification in knee OA and could result in clinical benefit. No current treatment is able to induce such changes. Larger, longer and randomised studies on joint distraction are warranted. PMID:21565898

Randomized Multi-site Trial of the Job Seekers’ Workshop in Patients with Substance Use Disorders

PubMed Central

Svikis, Dace S.; Keyser-Marcus, Lori; Stitzer, Maxine; Rieckmann, Traci; Safford, Lauretta; Loeb, Peter; Allen, Tim; Luna-Anderson, Carol; Back, Sudie E.; Cohen, Judith; DeBernardi, Michael A.; Dillard, Bruce; Forcehimes, Alyssa; Jaffee, William; Killeen, Therese; Kolodner, Ken; Levy, Michael; Pallas, Diane; Perl, Harold I.; Potter, Jennifer Sharpe; Provost, Scott; Reese, Karen; Sampson, Royce R.; Sepulveda, Allison; Snead, Ned; Wong, Conrad J.; Zweben, Joan

2012-01-01

Background Unemployment is associated with negative outcomes both during and after drug abuse treatment. Interventions designed to increase rates of employment may also improve drug abuse treatment outcomes. The purpose of this multi-site clinical trial was to evaluate the Job Seekers’ Workshop (JSW), a three session, manualized program designed to train patients in the skills needed to find and secure a job. Method Study participants were recruited through the NIDA Clinical Trials Network (CTN) from six psychosocial counseling (n=327) and five methadone maintenance (n=301) drug treatment programs. Participants were randomly assigned to either standard care (program-specific services plus brochure with local employment resources) (SC) or standard care plus JSW. Three 4-hr small group JSW sessions were offered weekly by trained JSW facilitators with ongoing fidelity monitoring. Results JSW and SC participants had similar 12- and 24-week results for the primary outcome measure (i.e., obtaining a new taxed job or enrollment in a training program), Specifically, one-fifth of participants at 12 weeks (20.1 – 24.3%) and nearly one-third at 24 weeks (31.4–31.9%) had positive outcomes, with “obtaining a new taxed job” accounting for the majority of cases. Conclusion JSW group participants did not have higher rates of employment/training than SC controls. Rates of job acquisition were modest for both groups, suggesting more intensive interventions may be needed. Alternate targets (e.g., enhancing patient motivation, training in job-specific skills) warrant further study as well. PMID:21802222

76 FR 62039 - Certain Hot-Rolled Carbon Steel Flat Products From India: Final Results of 2009-2010 Antidumping...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-06

... DEPARTMENT OF COMMERCE International Trade Administration [A-533-820] Certain Hot-Rolled Carbon... administrative review of the antidumping duty order on certain hot-rolled carbon steel flat products from India (``hot-rolled steel'') manufactured by Ispat Industries Limited (``Ispat''), JSW Steel Limited (``JSW...

76 FR 78612 - Certain Welded Carbon Steel Standard Pipes and Tubes From India: Rescission of Antidumping Duty...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-19

... Industries Ltd., Jindal Saw Ltd., Jindal Steel and Power Ltd., JSL Ltd., JSW Steel Ltd.\\1\\, Jotindra Steel... Industries Ltd., Welspun Group and all affiliates, Welspun Corp. Ltd., Welspun Trading Ltd., Welspun Steel..., Jindal Industries Ltd., Jindal Saw Ltd., Jindal Steel and Power Ltd., JSL Ltd., JSW Steel Ltd., Jotindra...

Radiological and biochemical effects (CTX-II, MMP-3, 8, and 13) of low-level laser therapy (LLLT) in chronic osteoarthritis in Al-Kharj, Saudi Arabia.

PubMed

S, Gopal Nambi; Kamal, Walid; George, Julie; Manssor, Elbagir

2017-02-01

Inflammation of synovial membrane and degeneration of articular cartilage in osteoarthritis (OA) lead to major changes in joint space width (JSW) and biochemical components such as collagen-II telopeptide (CTX-II) and matrix metallo protineases (MMP-3, 8, and 13). Low-level laser therapy (LLLT) is thought to have an analgesic effect as well as biomodulatory effect on microcirculation and cartilage regeneration in animal studies. The objective of this study was to examine the analgesic and biochemical effect of LLLT in patients with knee osteoarthritis. Subjects (n = 34) who fulfilled the selection criteria were randomly divided into active group (n = 17) and placebo group. Subjects in active group were irradiated laser with the frequency of 3 days per week for 4 weeks with the specific parameters on 8 different points on the joint at 1.5 J per point for 60 s for 8 points for a total dose of 12 J in a skin contact method. The placebo group was treated with the same probe with minimum emission of energy. Visual analog scale for pain intensity, joint space width, collagen-II telopeptide, and matrix metallo protinease-3, 8, and 13 was measured before treatment and at 4 and 8 weeks following treatment. Data are analyzed with mean values and standard deviation with p < 0.05. Baseline values of all outcome measures show insignificant difference (p > 0.05) in both groups which shows homogeneity. After 4- and 8-week treatment, active laser group shows more significant difference (p < 0.001) in all the parameters than the placebo laser group (p > 0.05). Our results show that low-level laser therapy was more efficient in reducing pain and improving cartilage thickness through biochemical changes.

Performance Acceleration on Production Machines Using the Overall Equipment Effectiveness (OEE) Approach

NASA Astrophysics Data System (ADS)

Mansur, A.; Rayendra, R.; Mastur, MI

2016-01-01

Mistakes during working can trigger a decrease in production level that may lead financial loss to the company. The factors that affect the mistakes are called losses, such as breakdown loss, set up/ adjustment loss, idling and minor stoppage loss, reduced speed loss, reduced yield loss, and rework loss. The objective of the research is to accelerate the performance of the JSW 330T machine in PT. YogyaPresisiTehnikatamaIndustri. JSW 330T is a machine that has the highest downtime numbers. The method for measuring the effectiveness is using the Overall Equipment Effectiveness (OEE). The results of the research show that the JWQ 330T has average rate of the effectiveness (OEE) of 52.66%, availability ratioof 73.43%, performance efficiency rate of 83.58% and quality rate of 84.6%. From the six big losses calculation, the factor that affects the most on the low score of OEE is the breakdown loss which is 58.85% with total time loss of 929.65 hours in a year.

Comparison of tibiofemoral joint space width measurements from standing CT and fixed flexion radiography.

PubMed

Segal, Neil A; Frick, Eric; Duryea, Jeffrey; Nevitt, Michael C; Niu, Jingbo; Torner, James C; Felson, David T; Anderson, Donald D

2017-07-01

The objective of this project was to determine the relationship between medial tibiofemoral joint space width measured on fixed-flexion radiographs and the three-dimensional joint space width distribution on low-dose, standing CT (SCT) imaging. At the 84-month visit of the Multicenter Osteoarthritis Study, 20 participants were recruited. A commercial SCT scanner for the foot and ankle was modified to image knees while standing. Medial tibiofemoral joint space width was assessed on radiographs at fixed locations from 15% to 30% of compartment width using validated software and on SCT by mapping the distances between three-dimensional subchondral bone surfaces. Individual joint space width values from radiographs were compared with three-dimensional joint space width values from corresponding sagittal plane locations using paired t-tests and correlation coefficients. For the four medial-most tibiofemoral locations, radiographic joint space width values exceeded the minimal joint space width on SCT by a mean of 2.0 mm and were approximately equal to the 61st percentile value of the joint space width distribution at each respective sagittal-plane location. Correlation coefficients at these locations were 0.91-0.97 and the offsets between joint space width values from radiographs and SCT measurements were consistent. There were greater offsets and variability in the offsets between modalities closer to the tibial spine. Joint space width measurements on fixed-flexion radiographs are highly correlated with three-dimensional joint space width from SCT. In addition to avoiding bony overlap obscuring the joint, a limitation of radiographs, the current study supports a role for SCT in the evaluation of tibiofemoral OA. © 2017 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 35:1388-1395, 2017. © 2017 Orthopaedic Research Society. Published by Wiley Periodicals, Inc.

76 FR 31938 - Certain Hot-Rolled Carbon Steel Flat Products From India: Notice of Preliminary Results of 2009...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-02

... DEPARTMENT OF COMMERCE International Trade Administration [A-533-820] Certain Hot-Rolled Carbon... conducting an administrative review of the antidumping duty order on certain hot-rolled carbon steel flat products from India (``hot-rolled steel'') manufactured by Ispat Industries Limited (``Ispat''), JSW Steel...

Growth kinetics and mass transport mechanisms of GaN columns by selective area metal organic vapor phase epitaxy

NASA Astrophysics Data System (ADS)

Wang, Xue; Hartmann, Jana; Mandl, Martin; Sadat Mohajerani, Matin; Wehmann, Hergo-H.; Strassburg, Martin; Waag, Andreas

2014-04-01

Three-dimensional GaN columns recently have attracted a lot of attention as the potential basis for core-shell light emitting diodes for future solid state lighting. In this study, the fundamental insights into growth kinetics and mass transport mechanisms of N-polar GaN columns during selective area metal organic vapor phase epitaxy on patterned SiOx/sapphire templates are systematically investigated using various pitch of apertures, growth time, and silane flow. Species impingement fluxes on the top surface of columns Jtop and on their sidewall Jsw, as well as, the diffusion flux from the substrate Jsub contribute to the growth of the GaN columns. The vertical and lateral growth rates devoted by Jtop, Jsw and Jsub are estimated quantitatively. The diffusion length of species on the SiOx mask surface λsub as well as on the sidewall surfaces of the 3D columns λsw are determined. The influences of silane on the growth kinetics are discussed. A growth model is developed for this selective area metal organic vapor phase epitaxy processing.

The relationship between clinical characteristics, radiographic osteoarthritis and 3D bone area: data from the osteoarthritis initiative.

PubMed

Barr, A J; Dube, B; Hensor, E M A; Kingsbury, S R; Peat, G; Bowes, M A; Conaghan, P G

2014-10-01

Radiographic measures of osteoarthritis (OA) are based upon two dimensional projection images. Active appearance modelling (AAM) of knee magnetic resonance imaging (MRI) enables accurate, 3D quantification of joint structures in large cohorts. This cross-sectional study explored the relationship between clinical characteristics, radiographic measures of OA and 3D bone area (tAB). Clinical data and baseline paired radiographic and MRI data, from the medial compartment of one knee of 2588 participants were obtained from the NIH Osteoarthritis Initiative (OAI). The medial femur (MF) and tibia (MT) tAB were calculated using AAM. 'OA-attributable' tAB (OA-tAB) was calculated using data from regression models of tAB of knees without OA. Associations between OA-tAB and radiographic measures of OA were investigated using linear regression. In univariable analyses, height, weight, and age in female knees without OA explained 43.1%, 32.1% and 0.1% of the MF tAB variance individually and 54.4% when included simultaneously in a multivariable model. Joint space width (JSW), osteophytes and sclerosis explained just 5.3%, 14.9% and 10.1% of the variance of MF OA-tAB individually and 17.4% when combined. Kellgren Lawrence (KL) grade explained approximately 20% of MF OA-tAB individually. Similar results were seen for MT OA-tAB. Height explained the majority of variance in tAB, confirming an allometric relationship between body and joint size. Radiographic measures of OA, derived from a single radiographic projection, accounted for only a small amount of variation in 3D knee OA-tAB. The additional structural information provided by 3D bone area may explain the lack of a substantive relationship with these radiographic OA measures. Copyright © 2014 The Authors. Published by Elsevier Ltd.. All rights reserved.

EFFECTS OF X-RAY BEAM ANGLE AND GEOMETRIC DISTORTION ON WIDTH OF EQUINE THORACOLUMBAR INTERSPINOUS SPACES USING RADIOGRAPHY AND COMPUTED TOMOGRAPHY-A CADAVERIC STUDY.

PubMed

Djernaes, Julie D; Nielsen, Jon V; Berg, Lise C

2017-03-01

The widths of spaces between the thoracolumbar processi spinosi (interspinous spaces) are frequently assessed using radiography in sports horses; however effects of varying X-ray beam angles and geometric distortion have not been previously described. The aim of this prospective, observational study was to determine whether X-ray beam angle has an effect on apparent widths of interspinous spaces. Thoracolumbar spine specimens were collected from six equine cadavers and left-right lateral radiographs and sagittal and dorsal reconstructed computed tomographic (CT) images were acquired. Sequential radiographs were acquired with each interspinous space in focus. Measurements were performed for each interspinous space in the focus position and up to eight angled positions as the interspinous space moved away from focus (±). Focus position measurements were compared to matching sagittal CT measurements. Effect of geometric distortion was evaluated by comparing the interspinous space in radiographs with sagittal and dorsal reconstructed CT images. A total of 49 interspinous spaces were sampled, yielding 274 measurements. X-ray beam angle significantly affected measured width of interspinous spaces in position +3 (P = 0.038). Changes in width did not follow a consistent pattern. Interspinous space widths in focus position were significantly smaller in radiographs compared to matching reconstructed CT images for backs diagnosed with kissing spine syndrome (P < 0.001). Geometric distortion markedly affected appearance of interspinous space width between planes. In conclusion, X-ray beam angle and geometric distortion influence radiographically measured widths of interspinous spaces in the equine thoracolumbar spine, and this should be taken into consideration when evaluating sport horses. © 2016 American College of Veterinary Radiology.

Targeting the Ron-DEK Signaling Axis in Breast Cancer

DTIC Science & Technology

2014-09-01

Health Services Grants R01CA116316 ( SIW ), R01HL875109 (JAC), T32ES007250 (AKA), T32CA117846-07 (PKW) and T32CA11784 (SEW and NMB), Department of Defense...Grant W81XWH-12-1-0194 ( SIW and SEW) and the Veteran’s Administration Grant BX000803 (SEW). JS-W is supported by the Government of the Spanish Junta de

Targeting the Ron-DEK Signaling Axis in Breast Cancer

DTIC Science & Technology

2014-09-01

Public Health Services Grants R01CA116316 ( SIW ), R01HL875109 (JAC), T32ES007250 (AKA), T32CA117846-07 (PKW) and T32CA11784 (SEW and NMB), Department of...Defense Grant W81XWH-12-1-0194 ( SIW and SEW) and the Veteran’s Administration Grant BX000803 (SEW). JS-W is supported by the Government of the Spanish

Size of the lower third molar space in relation to age in Serbian population.

PubMed

Zelić, Ksenija; Nedeljković, Nenad

2013-10-01

It is considered that the shortage of space is the major cause of the third molar impaction. The aim of this study was to establish the frequency of insufficient lower third molar eruption space in Serbian population, to question the differences in this frequency in the subjects of different age, to determine the influence of the lower third molar space (retromolar space) size on third molar eruption, and to investigate a possible correlation between the size of gonial angle and the space/third molar width ratio. Digital orthopantomograms were taken from 93 patients divided into two groups: early adult (16-18 years of age) and adult (18-26) patients. Retromolar space, mesiodistal third molar crown width, gonial angle and eruption levels were measured. The space/third molar width in early adult subjects was smaller (p < 0.0001) and insufficient space was significantly more frequent (p = 0.0003) than in adult patients. Considerably more third molars erupted in case of enough space in both age groups (p < 0.0001). There was no difference between the means of gonial angle size in relations to the available space. The retromolar space/third molar width ratio is more favorable in adult subjects. Gonial angle is not in correlation with the retromolar space/third molar width ratio.

Beam-width spreading of vortex beams in free space

NASA Astrophysics Data System (ADS)

Wang, Weiwei; Li, Jinhong; Duan, Meiling

2018-01-01

Based on the extended Huygens-Fresnel principle and the definition of second-order moments of the Wigner distribution function, the analytical expression for the beam-width spreading of Gaussian Schell-model (GSM) vortex beams in free space are derived, and used to study the influence of beam parameters on the beam-width spreading of GSM vortex beams. With the increment of the propagation distance, the beam-width spreading of GSM vortex beams will increase; the bigger the topological charge, spatial correlation length, wavelength and waist width are, the smaller the beam-width spreading is.

Assessment of Cabin Dimensions to Accommodate Infantry Soldiers for the Future Vertical Lift/Joint Multi-Role Medium-Class Aircraft

DTIC Science & Technology

2014-07-01

an official Department of the Army position unless so designated by other authorized documents. Citation of manufacturer’s or trade names does...The dimensions assessed included seat space widths, cabin ceiling heights, aisle widths, seating configurations, and cabin door widths. Emergency... seat spacing, 66-in. cabin ceiling height, 72-in. floor width, and 32-in. door width. These dimensions will help ensure that Soldiers have adequate

Determination of body width in brown and white layer pullets by image analyses.

PubMed

Giersberg, M F; Kemper, N; Hartung, J; Schrader, L; Spindler, B

2017-06-01

1. Specific legal requirements for keeping pullets are not available in the European Union. However, two of the most important rearing factors for pullets are sufficient perching and feeder space. Both factors represent horizontal space dimensions which derive from the body width of the birds. 2. The body width of two strains of layer pullets (brown (BL) and white (WL) layer pullets) based on the measurement of distances in digital images was conducted on front-view digital photographs of BL and WL pullets taken at 8, 12 and 19 weeks of life. 3. Depending on live weight, age and body position, BL pullets measured an average body width between 10.70 ± 1.10 and 13.96 ± 1.11 cm. The width of WL pullets ranged from 10.30 ± 0.86 to 13.00 ± 1.14 cm. 4. Compared with WL, BL pullets occupied more horizontal space during rearing. Age influenced the body width of BL and WL pullets at the end of rearing. The tested body positions of the pullets did not affect the measured body width. 5. The biometric data obtained in this study are a useful basis for developing legal requirements for pullets, especially for defining minimum perch width and feeder space allowances.

Sonographic analysis of the intercostal spaces for the application of high-intensity focused ultrasound therapy to the liver.

PubMed

Kim, Young-Sun; Park, Min Jung; Rhim, Hyunchul; Lee, Min Woo; Lim, Hyo Keun

2014-07-01

The purposes of this study were to assess the widths of the intercostal spaces of the right inferior human rib cage through which high-intensity focused ultrasound therapy would be applied for treating liver cancer and to elucidate the demographic factors associated with intercostal space width. From March 2013 to June 2013, the widths of the intercostal spaces and the ribs at six areas of the right inferior rib cage (area 1, lowest intercostal space on anterior axillary line and the adjacent upper rib; area 2, second-lowest intercostal space on anterior axillary line and the adjacent upper rib; areas 3 and 4, lowest and second-lowest spaces on midaxillary line; areas 5 and 6, lowest and second-lowest spaces on posterior axillary line) were sonographically measured in 466 patients (214 men, 252 women; mean age, 53.0 years) after an abdominal sonographic examination. Demographic factors and the presence or absence of chronic liver disease were evaluated by multivariate analysis to investigate which factors influence intercostal width. The width of the intercostal space was 19.7 ± 3.7 mm (range, 9-33 mm) at area 1, 18.3 ± 3.4 mm (range, 9-33 mm) at area 2, 17.4 ± 4.0 mm (range, 7-33 mm) at area 3, 15.4 ± 3.5 mm (range, 5-26 mm) at area 4, 17.2 ± 3.7 mm (range, 7-28 mm) at area 5, and 14.5 ± 3.6 mm (range, 4-26 mm) at area 6. The corresponding widths of the ribs were 15.2 ± 2.3 mm (range, 8-22 mm), 14.5 ± 2.3 mm (range, 9-22 mm), 13.2 ± 2.0 mm (range, 9-20), 14.3 ± 2.2 mm (range, 9-20 mm), 15.0 ± 2.2 mm (range, 10-22 mm), and 15.1 ± 2.3 mm (range, 8-21 mm). Only female sex was significantly associated with the narrower intercostal width at areas 1, 2, 3, and 5 (regression coefficient, 1.124-1.885; p = 0.01-0.04). There was substantial variation in the widths of the intercostal spaces of the right inferior rib cage such that the anterior and inferior aspects of the intercostal space were relatively wider. Women had significantly narrower intercostal spaces than men.

A multi-centre, open label, long-term follow-up study to evaluate the benefits of a new viscoelastic hydrogel (Hymovis®) in the treatment of knee osteoarthritis.

PubMed

Benazzo, F; Perticarini, L; Padolino, A; Castelli, A; Gifuni, P; Lovato, M; Manzini, C; Giordan, N

2016-03-01

To evaluate the long-term efficacy and safety of Hymovis® in the symptomatic treatment of knee osteoarthritis (OA). This is a prospective, multi-center, open label, phase III clinical study. Two intra-articular injections (3 mL) of Hymovis® (8 mg/mL HYADD® 4) were administered 1 week apart at the beginning of the study on day 0 and day 7 and after 6 months from baseline, on day 182 and 189. Follow-up assessment were conducted for 52 weeks. 50 subjects, > 40 years old, with knee OA, with clinical and radiological confirm, complain pain in the target knee were enrolled. The variables considered were: WOMAC questionnaire, Joint Space Width (JSW), OMERACT OARSI responder criteria, EQ-5D questionnaire, rescue medication consumption. After the injections of Hymovis®, pain perceived by the patient when walking on a flat surface (WOMAC A1 score) significantly improves at the end of the study respect to the baseline. WOMAC stiffness, physical function and total score significantly improve during the study since 3 months after treatment, and it is maintained up to the end of the study (p < 0.001). By the x-ray analysis of knee, a radiological progression of OA was observed in the 26% of patients at the end of the study, while 88% of patients result to be responder to the therapy classified as per OMERACT-OARSI criteria. The EQ-5D weighted index increased significantly, against baseline, at each study time point (p < 0.001). Investigator's and patient's global assessment of the disease measured by the VAS both show a marked improvement in patient's health conditions. Results from this study confirm that Hymovis® alleviate the knee pain since the first treatment cycle. The patients treated with two cycles of intra-articular injections of Hymovis® have a progressive pain reduction that is maintained up to one year after the treatment start with improve of all the scores considered in this study. Hymovis® is effective and safe in symptomatic treatment of painful knee OA.

The Intensive Diet and Exercise for Arthritis (IDEA) trial: 18-month radiographic and MRI outcomes.

PubMed

Hunter, D J; Beavers, D P; Eckstein, F; Guermazi, A; Loeser, R F; Nicklas, B J; Mihalko, S L; Miller, G D; Lyles, M; DeVita, P; Legault, C; Carr, J J; Williamson, J D; Messier, S P

2015-07-01

Report the radiographic and magnetic resonance imaging (MRI) structural outcomes of an 18-month study of diet-induced weight loss, with or without exercise, compared to exercise alone in older, overweight and obese adults with symptomatic knee osteoarthritis (OA). Prospective, single-blind, randomized controlled trial that enrolled 454 overweight and obese (body mass index, BMI = 27-41 kg m(-2)) older (age ≥ 55 yrs) adults with knee pain and radiographic evidence of femorotibial OA. Participants were randomized to one of three 18-month interventions: diet-induced weight loss only (D); diet-induced weight loss plus exercise (D + E); or exercise-only control (E). X-rays (N = 325) and MRIs (N = 105) were acquired at baseline and 18 months follow-up. X-ray and MRI (cartilage thickness and semi-quantitative (SQ)) results were analyzed to compare change between groups at 18-month follow-up using analysis of covariance (ANCOVA) adjusted for baseline values, baseline BMI, and gender. Mean baseline descriptive characteristics of the cohort included: age, 65.6 yrs; BMI 33.6 kg m(-2); 72% female; 81% white. There was no significant difference between groups in joint space width (JSW) loss; D -0.07 (SE 0.22) mm, D + E -0.27 (SE 0.22) mm and E -0.16 (SE 0.24) mm (P = 0.79). There was also no significant difference in MRI cartilage loss between groups; D -0.10(0.05) mm, D + E -0.13(0.04) mm and E -0.05(0.04) mm (P = 0.42). Despite the potent effects of weight loss in this study on symptoms as well as mechanistic outcomes (such as joint compressive force and markers of inflammation), there was no statistically significant difference between the three active interventions on the rate of structural progression either on X-ray or MRI over 18-months. Copyright © 2015 Osteoarthritis Research Society International. Published by Elsevier Ltd. All rights reserved.

The importance of costoclavicular space on possible compression of the subclavian artery in the thoracic outlet region: a radio-anatomical study.

PubMed

Kaplan, Tevfik; Comert, Ayhan; Esmer, Ali Firat; Ataç, Gökçe Kaan; Acar, Halil Ibrahim; Ozkurt, Bulent; Tekdemir, Ibrahim; Han, Serdar

2018-04-16

The purposes of this study were to identify possible compression points along the transit route of the subclavian artery and to provide a detailed anatomical analysis of areas that are involved in the surgical management of the thoracic outlet syndrome (TOS). The results of the current study are based on measurements from cadavers, computed tomography (CT) scans and dry adult first ribs. The width and length of the interscalene space and the width of the costoclavicular passage were measured on 18 cervical dissections in 9 cadavers, on 50 dry first ribs and on CT angiography sections from 15 patients whose conditions were not related to TOS. The average width and length of the interscalene space in cadavers were 15.28 ± 1.94 mm and 15.98 ± 2.13 mm, respectively. The widths of the costoclavicular passage (12.42 ± 1.43 mm) were significantly narrower than the widths and lengths of the interscalene space in cadavers (P < 0.05). The average width and length of the interscalene space (groove for the subclavian artery) in 50 dry ribs were 15.53 ± 2.12 mm and 16.12 ± 1.95 mm, respectively. In CT images, the widths of the costoclavicular passage were also significantly narrower than those of the interscalene space (P < 0.05). The measurements from cadavers, dry first ribs and CT images were not significantly different (P > 0.05). Our results showed that the costoclavicular width was the narrowest space along the passage route of the subclavian artery. When considering the surgical decompression of the subclavian artery for TOS, this narrowest area should always be kept in mind. Since measurements from CT images and cadavers were significantly similar, CT measurements may be used to evaluate the thoracic outlet region in patients with TOS.

EFFECT OF JOB SKILLS TRAINING ON EMPLOYMENT AND JOB SEEKING BEHAVIORS IN AN AMERICAN INDIAN SUBSTANCE ABUSE TREATMENT SAMPLE

PubMed Central

Foley, K.; Pallas, D.; Forcehimes, A. A.; Houck, J. M.; Bogenschutz, M. P.; Keyser-Marcus, L.; Svikis, D.

2011-01-01

Employment difficulties are common among American Indian individuals in substance abuse treatment. To address this problem, the Southwest Node of NIDA’s Clinical Trials Network conducted a single-site adaptation of its national Job Seekers Workshop study in an American Indian treatment program, Na’Nizhoozhi Center (NCI). 102 (80% men, 100% American Indian) participants who were in residential treatment and currently unemployed were randomized to (1) a three session, manualized program (Job seekers workshop: JSW) or (2) a 40-minute Job Interviewing Video: JIV). Outcomes were assessed at 3-month follow up: 1) number of days to a new taxed job or enrollment in a job-training program, and 2) total hours working or enrolled in a job-training program. No significant differences were found between the two groups for time to a new taxed job or enrollment in a job-training program. There were no significant differences between groups in substance use frequency at 3-month follow-up. These results do not support the use of the costly and time-consuming JSW intervention in this population and setting. Despite of the lack of a demonstrable treatment effect, this study established the feasibility of including a rural American Indian site in a rigorous CTN trial through a community-based participatory research approach. PMID:21818173

PET - radiopharmaceutical facilities at Washington University Medical School - an overview

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dence, C.S.; Welch, M.J.

1994-12-31

The PET program at Washington University has evolved over more than three decades of research and development in the use of positron-emitting isotopes in medicine and biology. In 1962 the installation of the first hospital cyclotron in the USA was accomplished. This first machine was an Allis Chalmers (AC) cyclotron and it was operated until July, 1990. Simultaneously with this cyclotron the authors also ran a Cyclotron Corporation (TCC) CS-15 cyclotron that was purchased in 1977. Both of these cyclotrons were maintained in-house and operated with a relatively small downtime (approximately 3.5%). After the dismantling of the AC machine inmore » 1990, a Japanese Steel Works 16/8 (JSW-16/8) cyclotron was installed in the vault. Whereas the AC cyclotron could only accelerate deuterons (6.2 MeV), the JSW - 16/8 machine can accelerate both protons and deuterons, so all of the radiopharmaceuticals can be produced on either of the two presently owned accelerators. At the end of May 1993, the medical school installed the first clinical Tandem Cascade Accelerator (TCA) a collaboration with Science Research Laboratories (SRL) of Somerville, MA. Preliminary target testing, design and development are presently under way. In 1973, the University installed the first operational PETT device in the country, and at present there is a large basic science and clinical research program involving more than a hundred staff in nuclear medicine, radiation sciences, neurology, neurosurgery, psychiatry, cardiology, pulmonary medicine, oncology, and surgery.« less

Pool spacing in forest channels

Treesearch

David R. Montgomery; John M. Buffington; Richard D. Smith; Kevin M. Schmidt; George Pess

1995-01-01

Field surveys of stream channels in forested mountain drainage basins in southeast Alaska and Washington reveal that pool spacing depends on large woody debris (LWD) loading and channel type, slope, and width. Mean pool spacing in pool-riffle, plane-bed, and forced pool-riffle channels systematically decreases from greater than 13 channel widths per pool to less than 1...

Ada (trade name) Compiler Validation Summary Report: Rational Environment, Version A.2.0.6 for Rational R1000.

DTIC Science & Technology

1985-05-24

RD-Ali57 830 ADA (TRADE NAME) COMPILER VALIDATION SUMMARY REPORT: 1/ RATIONAL ENVIRONMENT VERSION R296 FOR RATIONAL Ri888 (U) SOFTECH INC FAIRBORN OH...USoCPY WSSOS.UTM iTS GWAT % : 4 AVF Control Number: AVF-VSR-09.0585 0 IAda Compiler Validation Summary Report: Rational Environment Version A.2.0.6 For...1985 to May 1986 Environment Version A.2-0.6 For Rational RlOOO (Final) ______________ S. PLNOPftaiJSw mO. ftLOW@N WuCU ). aulwtar111. CONiTRACT 00

Observations of narrow microburst trains in the geomagnetic storm of August 4-6, 1972

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, R.R.

1973-04-01

In the intense geomagnetic disturbances of early August 1972, auroral zone microburst trains were observed at balloon altitude and found to be significantly narrower in burst width and spacing than microbursts found previously at the same site. These observations suggest that the spacing of microburst peaks, as well as their width, is related to variations in the power spectrum of a magnetospheric acceleration process rather than the bounce motions of electrons in the geomagnetic field or the modulation of electron precipitation by drift waves in magnetospheric plasma. In the geomagnetic activity that followed the solar flares in early August 1972,more » intense fluxes of auroral x rays were encountered during balloon flights launched from College, Alaska. Although much of the time variations of the x-ray fluxes observed during these flights represented known features of electron precipitation at auroral latitudes, one new and distinct feature was evident. In particular, it was found that the widths and spacings of auroral zone microbursts (Anderson and Milton, 1964) on this occasion were significantly smaller than those observed previously on many balloon flights from the same site. Thus, instead of microburst trains with widths at half-intensity points of ~0.2 sec and spacings of ~0.6 sec, the majority of the microbursts encountered on two flights from College had widths of ~0.1 sec and spacings of ~0.4 sec. (auth)« less

Differences between dentitions with palatally and labially located maxillary canines observed in incisor width, dental morphology and space conditions.

PubMed

Artmann, L; Larsen, H J; Sørensen, H B; Christensen, I J; Kjaer, I

2010-06-01

To analyze the interrelationship between incisor width, deviations in the dentition and available space in the dental arch in palatally and labially located maxillary ectopic canine cases. Size: On dental casts from 69 patients (mean age 13 years 6 months) the mesiodistal widths of each premolar, canine and incisor were measured and compared with normal standards. Dental deviations: Based on panoramic radiographs from the same patients the dentitions were grouped accordingly: Group I: normal morphology; Group IIa: deviations in the dentition within the maxillary incisors only; Group IIb: deviations in the dentition in general. Descriptive statistics for the tooth sizes and dental deviations were presented by the mean and 95% confidence limits for the mean and the p-value for the T-statistic. Space: Space was expresses by subtracting the total tooth sizes of incisors, canines and premolars from the length of the arch segments. Size of lateral maxillary incisor: The widths of the lateral incisors were significantly different in groups I, IIa and IIb (p=0.016) and in cases with labially located ectopic canines on average 0.65 (95% CI:0.25-1.05, p=0.0019) broader than lateral incisors in cases with palatally located ectopic canines. Space: Least available space was observed in cases with labially located canines. The linear model did show a difference between palatally and labially located ectopic canines (p=0.03). Space related to deviations in the dentition: When space in the dental arch was related to dental deviations (groups I, IIa and IIb), the cases in group IIb with palatally located canines had significantly more space compared with I and IIa. Two subgroups of palatally located ectopic maxillary canine cases based on registration of space, incisor width and deviations in the morphology of the dentition were identified.

A polynomial chaos expansion based molecular dynamics study for probabilistic strength analysis of nano-twinned copper

NASA Astrophysics Data System (ADS)

Mahata, Avik; Mukhopadhyay, Tanmoy; Adhikari, Sondipon

2016-03-01

Nano-twinned structures are mechanically stronger, ductile and stable than its non-twinned form. We have investigated the effect of varying twin spacing and twin boundary width (TBW) on the yield strength of the nano-twinned copper in a probabilistic framework. An efficient surrogate modelling approach based on polynomial chaos expansion has been proposed for the analysis. Effectively utilising 15 sets of expensive molecular dynamics simulations, thousands of outputs have been obtained corresponding to different sets of twin spacing and twin width using virtual experiments based on the surrogates. One of the major outcomes of this work is that there exists an optimal combination of twin boundary spacing and twin width until which the strength can be increased and after that critical point the nanowires weaken. This study also reveals that the yield strength of nano-twinned copper is more sensitive to TBW than twin spacing. Such robust inferences have been possible to be drawn only because of applying the surrogate modelling approach, which makes it feasible to obtain results corresponding to 40 000 combinations of different twin boundary spacing and twin width in a computationally efficient framework.

Semantic, perceptual and number space: relations between category width and spatial processing.

PubMed

Brugger, Peter; Loetscher, Tobias; Graves, Roger E; Knoch, Daria

2007-05-17

Coarse semantic encoding and broad categorization behavior are the hallmarks of the right cerebral hemisphere's contribution to language processing. We correlated 40 healthy subjects' breadth of categorization as assessed with Pettigrew's category width scale with lateral asymmetries in perceptual and representational space. Specifically, we hypothesized broader category width to be associated with larger leftward spatial biases. For the 20 men, but not the 20 women, this hypothesis was confirmed both in a lateralized tachistoscopic task with chimeric faces and a random digit generation task; the higher a male participant's score on category width, the more pronounced were his left-visual field bias in the judgement of chimeric faces and his small-number preference in digit generation ("small" is to the left of "large" in number space). Subjects' category width was unrelated to lateral displacements in a blindfolded tactile-motor rod centering task. These findings indicate that visual-spatial functions of the right hemisphere should not be considered independent of the same hemisphere's contribution to language. Linguistic and spatial cognition may be more tightly interwoven than is currently assumed.

Losses analysis of soft magnetic ring core under sinusoidal pulse width modulation (SPWM) and space vector pulse width modulation (SVPWM) excitations

NASA Astrophysics Data System (ADS)

Gao, Hezhe; Li, Yongjian; Wang, Shanming; Zhu, Jianguo; Yang, Qingxin; Zhang, Changgeng; Li, Jingsong

2018-05-01

Practical core losses in electrical machines differ significantly from those experimental results using the standardized measurement method, i.e. Epstein Frame method. In order to obtain a better approximation of the losses in an electrical machine, a simulation method considering sinusoidal pulse width modulation (SPWM) and space vector pulse width modulation (SVPWM) waveforms is proposed. The influence of the pulse width modulation (PWM) parameters on the harmonic components in SPWM and SVPWM is discussed by fast Fourier transform (FFT). Three-level SPWM and SVPWM are analyzed and compared both by simulation and experiment. The core losses of several ring samples magnetized by SPWM, SVPWM and sinusoidal alternating current (AC) are obtained. In addition, the temperature rise of the samples under SPWM, sinusoidal excitation are analyzed and compared.

Subregional laminar cartilage MR spin-spin relaxation times (T2) in osteoarthritic knees with and without medial femorotibial cartilage loss - data from the Osteoarthritis Initiative (OAI).

PubMed

Wirth, W; Maschek, S; Beringer, P; Eckstein, F

2017-08-01

To explore whether subregional laminar femorotibial cartilage spin-spin relaxation time (T2) is associated with subsequent radiographic progression and cartilage loss and/or whether one-year change in subregional laminar femorotibial cartilage T2 is associated with concurrent progression in knees with established radiographic OA (ROA). In this case-control study, Osteoarthritis Initiative (OAI) knees with medial femorotibial progression were selected based on one-year loss in both quantitative cartilage thickness Magnetic resonance imaging (MRI) and radiographic joint space width (JSW). Non-progressor knees were matched by sex, Body mass index (BMI), baseline Kellgren-Lawrence-grade (2/3), and pain. Baseline and one-year follow-up superficial and deep cartilage T2 was analyzed in 16 femorotibial subregions using multi-echo spin-echo MRI. 37 knees showed medial femorotibial progression whereas 37 matched controls had no medial or lateral compartment progression. No statistically significant baseline differences between progressor and non-progressor knees in medial femorotibial cartilage T2 were observed in the superficial (48.9 ± 3.0 ms; 95% CI: [47.9, 49.9] vs 47.8 ± 3.6 ms; 95% CI: [46.6, 49.0], P = 0.07) or deep cartilage layer (40.8 ± 3.6 ms; 95% CI: [39.5, 42.0] vs 40.1 ± 4.7 ms; 95% CI: [38.5, 41.6], P = 0.29). Concurrent T2 change was more pronounced in the deep than the superficial cartilage layer. In the medial femorotibial compartment (MFTC), longitudinal change was greater in the deep layer of progressor than non-progressor knees (1.8 ± 4.5 ms; 95% CI: [0.3, 3.3] vs -0.2 ± 1.9 ms; 95% CI: [-0.8, 0.5], P = 0.02), whereas no difference was observed in the superficial layer. Medial compartment cartilage T2 did not appear to be a strong prognostic factor for subsequent structural progression in the same compartment of knees with established ROA, when appropriately controlling for covariates. Yet, deep layer T2 change in the medial compartment occurred concurrent with medial femorotibial progression. Copyright © 2017 Osteoarthritis Research Society International. Published by Elsevier Ltd. All rights reserved.

Comparing fixed and variable-width Gaussian networks.

PubMed

Kůrková, Věra; Kainen, Paul C

2014-09-01

The role of width of Gaussians in two types of computational models is investigated: Gaussian radial-basis-functions (RBFs) where both widths and centers vary and Gaussian kernel networks which have fixed widths but varying centers. The effect of width on functional equivalence, universal approximation property, and form of norms in reproducing kernel Hilbert spaces (RKHS) is explored. It is proven that if two Gaussian RBF networks have the same input-output functions, then they must have the same numbers of units with the same centers and widths. Further, it is shown that while sets of input-output functions of Gaussian kernel networks with two different widths are disjoint, each such set is large enough to be a universal approximator. Embedding of RKHSs induced by "flatter" Gaussians into RKHSs induced by "sharper" Gaussians is described and growth of the ratios of norms on these spaces with increasing input dimension is estimated. Finally, large sets of argminima of error functionals in sets of input-output functions of Gaussian RBFs are described. Copyright © 2014 Elsevier Ltd. All rights reserved.

The effect of increased intra-abdominal pressure on orbital subarachnoid space width and intraocular pressure.

PubMed

Liu, Su-Meng; Wang, Ning-Li; Zuo, Zhen-Tao; Chen, Wei-Wei; Yang, Di-Ya; Li, Zhen; Cao, Yi-Wen

2018-02-01

In accordance with the trans-lamina cribrosa pressure difference theory, decreasing the trans-lamina cribrosa pressure difference can relieve glaucomatous optic neuropathy. Increased intracranial pressure can also reduce optic nerve damage in glaucoma patients, and a safe, effective and noninvasive way to achieve this is by increasing the intra-abdominal pressure. The purpose of this study was to observe the changes in orbital subarachnoid space width and intraocular pressure at elevated intra-abdominal pressure. An inflatable abdominal belt was tied to each of 15 healthy volunteers, aged 22-30 years (12 females and 3 males), at the navel level, without applying pressure to the abdomen, before they laid in the magnetic resonance imaging machine. The baseline orbital subarachnoid space width around the optic nerve was measured by magnetic resonance imaging at 1, 3, 9, and 15 mm behind the globe. The abdominal belt was inflated to increase the pressure to 40 mmHg (1 mmHg = 0.133 kPa), then the orbital subarachnoid space width was measured every 10 minutes for 2 hours. After removal of the pressure, the measurement was repeated 10 and 20 minutes later. In a separate trial, the intraocular pressure was measured for all the subjects at the same time points, before, during and after elevated intra-abdominal pressure. Results showed that the baseline mean orbital subarachnoid space width was 0.88 ± 0.1 mm (range: 0.77-1.05 mm), 0.77 ± 0.11 mm (range: 0.60-0.94 mm), 0.70 ± 0.08 mm (range: 0.62-0.80 mm), and 0.68 ± 0.08 mm (range: 0.57-0.77 mm) at 1, 3, 9, and 15 mm behind the globe, respectively. During the elevated intra-abdominal pressure, the orbital subarachnoid space width increased from the baseline and dilation of the optic nerve sheath was significant at 1, 3 and 9 mm behind the globe. After decompression of the abdominal pressure, the orbital subarachnoid space width normalized and returned to the baseline value. There was no significant difference in the intraocular pressure before, during and after the intra-abdominal pressure elevation. These results verified that the increased intra-abdominal pressure widens the orbital subarachnoid space in this acute trial, but does not alter the intraocular pressure, indicating that intraocular pressure is not affected by rapid increased intra-abdominal pressure. This study was registered in the Chinese Clinical Trial Registry (registration number: ChiCTR-ONRC-14004947).

Minimum Weight Design of a Leaf Spring Tapered in Thickness and Width for the Hubble Space Telescope-Space Support Equipment

NASA Technical Reports Server (NTRS)

Rodriguez, P. I.

1990-01-01

A linear elastic solution to the problem of minimum weight design of cantilever beams with variable width and depth is presented. The solution shown is for the specific application of the Hubble Space Telescope maintenance mission hardware. During these maintenance missions, delicate instruments must be isolated from the potentially damaging vibration environment of the space shuttle cargo bay during the ascent and descent phases. The leaf springs are designed to maintain the isolation system natural frequency at a level where load transmission to the instruments in a minimum. Nonlinear programming is used for the optimization process. The weight of the beams is the objective function with the deflection and allowable bending stress as the constraint equations. The design variables are the width and depth of the beams at both the free and the fixed ends.

Equivalence of linear canonical transform domains to fractional Fourier domains and the bicanonical width product: a generalization of the space-bandwidth product.

PubMed

Oktem, Figen S; Ozaktas, Haldun M

2010-08-01

Linear canonical transforms (LCTs) form a three-parameter family of integral transforms with wide application in optics. We show that LCT domains correspond to scaled fractional Fourier domains and thus to scaled oblique axes in the space-frequency plane. This allows LCT domains to be labeled and ordered by the corresponding fractional order parameter and provides insight into the evolution of light through an optical system modeled by LCTs. If a set of signals is highly confined to finite intervals in two arbitrary LCT domains, the space-frequency (phase space) support is a parallelogram. The number of degrees of freedom of this set of signals is given by the area of this parallelogram, which is equal to the bicanonical width product but usually smaller than the conventional space-bandwidth product. The bicanonical width product, which is a generalization of the space-bandwidth product, can provide a tighter measure of the actual number of degrees of freedom, and allows us to represent and process signals with fewer samples.

Variable-Period Undulators For Synchrotron Radiation

DOEpatents

Shenoy, Gopal; Lewellen, John; Shu, Deming; Vinokurov, Nikolai

2005-02-22

A new and improved undulator design is provided that enables a variable period length for the production of synchrotron radiation from both medium-energy and high-energy storage rings. The variable period length is achieved using a staggered array of pole pieces made up of high permeability material, permanent magnet material, or an electromagnetic structure. The pole pieces are separated by a variable width space. The sum of the variable width space and the pole width would therefore define the period of the undulator. Features and advantages of the invention include broad photon energy tunability, constant power operation and constant brilliance operation.

Magnetization reversal in ferromagnetic wires patterned with antiferromagnetic gratings

NASA Astrophysics Data System (ADS)

Sani, S. R.; Liu, F.; Ross, C. A.

2017-04-01

The magnetic reversal behavior is examined for exchange-biased ferromagnetic/antiferromagnetic nanostructures consisting of an array of 10 nm thick Ni80Fe20 stripes with width 200 nm and periodicity 400 nm, underneath an orthogonal array of 10 nm thick IrMn stripes with width ranging from 200 nm to 500 nm and periodicity from 400 nm to 1 μm. The Ni80Fe20 stripes show a hysteresis loop with one step when the IrMn width and spacing are small. However, upon increasing the IrMn width and spacing, the hysteresis loops showed two steps as the pinned and unpinned sections of the Ni80Fe20 stripes switch at different fields. Micromagnetic modeling reveals the influence of geometry on the reversal behavior.

Plain radiography or magnetic resonance imaging (MRI): Which is better in assessing outcome in clinical trials of disease-modifying osteoarthritis drugs? Summary of a debate held at the World Congress of Osteoarthritis 2014.

PubMed

Eckstein, Felix; Le Graverand, Marie-Pierre Hellio

2015-12-01

Osteoarthritis (OA) is the most common disease of synovial joints and currently lacks treatment options that modify structural pathology. Imaging is ideally suited for directly evaluating efficacy of disease-modifying OA drugs (DMOADs) in clinical trials, with plain radiography and MRI being most often applied. The current article is based on a debate held on April 26, 2014, at the World Congress of Osteoarthritis: The authors were invited to contrast strengths and limitations of both methods, highlighting scientific evidence on reliability, construct-validity, and correlations with clinical outcome, and comparing their sensitivity to change in knee OA and sensitivity to DMOAD treatment. The authors concluded that MRI provides more comprehensive information on articular tissues pathology, and that implementation of radiography in clinical trials remains a challenge. However, neither technique has thus far been demonstrated to be strongly superior over the other; for the time being it therefore appears advisable to use both in parallel in clinical trials, to provide more evidence on their relative performance. Radiographic JSW strongly depends on adequate positioning; it is not specific to cartilage loss but also to the meniscus. MRI provides somewhat superior sensitivity to change compared with the commonly used non-fluoroscopic radiographic acquisition protocols, and has recently provided non-location-dependent measures of cartilage thickness loss and gain, which are potentially more sensitive in detecting DMOAD effects than radiographic JSW or region-specific MRI. Non-location-dependent measures of cartilage thickness change should thus be explored further in context of anabolic and anti-catabolic DMOADs. Copyright © 2015 Elsevier Inc. All rights reserved.

Five Years' Growth of Pruned and Unpruned Cottonwood Planted at 40- by 40-Foot Spacing

Treesearch

Roger M. Krinard

1979-01-01

Four pruning treatments have been applied for 5 years on cottonwood (Populus deltoides Bartr.) select clone Stoneville 66, planted at 40- by 40-ft spacing. As pruning severity increased, average diameter and maximum crown width decreased. Diameters ranged from 9.2 inches for trees pruned half of height yearly to 11.4 inches for unpruned trees; crown widths ranged from...

Determining Metacarpophalangeal Flexion Angle Tolerance for Reliable Volumetric Joint Space Measurements by High-resolution Peripheral Quantitative Computed Tomography.

PubMed

Tom, Stephanie; Frayne, Mark; Manske, Sarah L; Burghardt, Andrew J; Stok, Kathryn S; Boyd, Steven K; Barnabe, Cheryl

2016-10-01

The position-dependence of a method to measure the joint space of metacarpophalangeal (MCP) joints using high-resolution peripheral quantitative computed tomography (HR-pQCT) was studied. Cadaveric MCP were imaged at 7 flexion angles between 0 and 30 degrees. The variability in reproducibility for mean, minimum, and maximum joint space widths and volume measurements was calculated for increasing degrees of flexion. Root mean square coefficient of variance values were < 5% under 20 degrees of flexion for mean, maximum, and volumetric joint spaces. Values for minimum joint space width were optimized under 10 degrees of flexion. MCP joint space measurements should be acquired at < 10 degrees of flexion in longitudinal studies.

Modelling of subarachnoid space width changes in apnoea resulting as a function of blood flow parameters.

PubMed

Kalicka, Renata; Mazur, Kamila; Wolf, Jacek; Frydrychowski, Andrzej F; Narkiewicz, Krzysztof; Winklewski, Pawel J

2017-09-01

During apnoea, the pial artery is subjected to two opposite physiological processes: vasoconstriction due to elevated blood pressure and vasorelaxation driven by rising pH in the brain parenchyma. We hypothesized that the pial artery response to apnoea may vary, depending on which process dominate. Apnoea experiments were performed in a group of 19 healthy, non-smoking volunteers (9 men and 10 women). The following parameters were obtained for further analysis: blood pressure, the cardiac (from 0.5 to 5.0Hz) and slow (<0.5Hz) components of subarachnoid space width, heart rate, mean cerebral blood flow velocity in the internal carotid artery, pulsatility and resistivity index, internal carotid artery diameter, blood oxygen saturation and end-tidal carbon dioxide. The experiment consisted of three apnoeas, sequentially: 30s, 60s and maximal apnoea. The breath-hold was separated for 5minute rest. The control process is sophisticated, involving internal cross-couplings and cross-dependences. The aim of work was to find a mathematical dependence between data. Unexpectedly, the modelling revealed two different reactions, on the same experimental procedure. As a consequence, there are two subsets of cardiac subarachnoid space width responses to breath-hold in humans. A positive cardiac subarachnoid space width change to apnoea depends on changes in heart rate and cerebral blood flow velocity. A negative cardiac subarachnoid space width change to apnoea is driven by heart rate, mean arterial pressure and pulsatility index changes. The described above two different reactions to experimental breath-hold provides new insights into our understanding of the complex mechanisms governing the adaptation to apnoea in humans. We proposed a mathematical methodology that can be used in further clinical research. Copyright © 2017 Elsevier Inc. All rights reserved.

Split-cross-bridge resistor for testing for proper fabrication of integrated circuits

NASA Technical Reports Server (NTRS)

Buehler, M. G. (Inventor)

1985-01-01

An electrical testing structure and method is described whereby a test structure is fabricated on a large scale integrated circuit wafer along with the circuit components and has a van der Pauw cross resistor in conjunction with a bridge resistor and a split bridge resistor, the latter having two channels each a line width wide, corresponding to the line width of the wafer circuit components, and with the two channels separated by a space equal to the line spacing of the wafer circuit components. The testing structure has associated voltage and current contact pads arranged in a two by four array for conveniently passing currents through the test structure and measuring voltages at appropriate points to calculate the sheet resistance, line width, line spacing, and line pitch of the circuit components on the wafer electrically.

Changes in temporomandibular joint spaces after arthroscopic disc repositioning: a self-control study

PubMed Central

Kai Hu, Ying; Abdelrehem, Ahmed; Yang, Chi; Cai, Xie Yi; Xie, Qian Yang; Sah, Manoj Kumar

2017-01-01

Disc repositioning is a common procedure for patients with anterior disc displacement (ADD). The purpose of this retrospective record-based study was to evaluate changes in the widths of joint spaces and condylar position changes in patients with unilateral ADD following arthroscopic disc repositioning, with the healthy sides as self-control, using magnetic resonance images (MRI).Widths of anterior, superior, and posterior joint spaces (AS, SS, and PS) were measured. The condylar position was described as anterior, centric or posterior, expressed as . Paired-t test and Chi-square test were used to analyze the data. Fifty-four records conformed to the inclusion criteria (mean age of 21.02 years). Widths of SS and PS increased significantly after surgery (P < 0.001) on the operative sides, while joint spaces of healthy sides and AS of operative sides had no significant changes. Dominant location of condyles of operative sides changed from a posterior position to an anterior position, while healthy sides were mostly centric condylar position no matter preoperatively or postoperatively. Therefore, the results of this study indicate that unilateral arthroscopic disc repositioning significantly increases the posterior and superior spaces of the affected joints, without affecting spaces of the healthy sides. PMID:28361905

Resolution Limits of Nanoimprinted Patterns by Fluorescence Microscopy

NASA Astrophysics Data System (ADS)

Kubo, Shoichi; Tomioka, Tatsuya; Nakagawa, Masaru

2013-06-01

The authors investigated optical resolution limits to identify minimum distances between convex lines of fluorescent dye-doped nanoimprinted resist patterns by fluorescence microscopy. Fluorescent ultraviolet (UV)-curable resin and thermoplastic resin films were transformed into line-and-space patterns by UV nanoimprinting and thermal nanoimprinting, respectively. Fluorescence immersion observation needed an immersion medium immiscible to the resist films, and an ionic liquid of triisobutyl methylphosphonium tosylate was appropriate for soluble thermoplastic polystyrene patterns. Observation with various numerical aperture (NA) values and two detection wavelength ranges showed that the resolution limits were smaller than the values estimated by the Sparrow criterion. The space width to identify line patterns became narrower as the line width increased. The space width of 100 nm was demonstrated to be sufficient to resolve 300-nm-wide lines in the detection wavelength range of 575-625 nm using an objective lens of NA= 1.40.

Evaluation of arch width variations among different skeletal patterns in South Indian population.

PubMed

Prasad, Mandava; Kannampallil, Senny Thomas; Talapaneni, Ashok Kumar; George, Suja Ani; Shetty, Sharath Kumar

2013-01-01

Anterior cranial base can be taken as a reference line (SN) to determine the steepness of mandibular plane. Subjects with high mandibular plane angle tend to have a long face and one with low MP-SN angle has a shorter face. This study was done to investigate if dental arch widths correlated with vertical facial types and if there are any differences in arch widths between untreated male and female adults in South Indian population. Lateral cephalogram and dental casts were obtained from 180 untreated South Indian adults (90 males and 90 females) above 18 year old with no cross bite, minimal crowding and spacing. The angle between the anterior cranial base and the mandibular plane was measured on lateral cephalogram of each patient. Dental casts were used to obtain comprehensive dental measurements including maxillary and mandibular inter canine, inter premolar and inter molar widths, as well as amount of crowding or spacing. The results showed that male arch widths were significantly larger than those of females (P < 0.05) and there was a significant decrease in inter arch width as the MP-SN angle increased in untreated adult South Indian population. The results obtained in our study when compared with studies done in other population groups showed that there is difference in inter arch widths according to ethnicity and race. It was concluded that the dental arch width is associated with gender, race and vertical facial morphology. Thus using individualized arch wires according to each patient's pre treatment arch form and width is suggested during orthodontic treatment.

On the use of space photography for identifying transportation routes: A summary of problems

NASA Technical Reports Server (NTRS)

Simonett, D. S.; Henderson, F. M.; Egbert, D. D.

1970-01-01

It has been widely suggested that space photography may be used for updating maps of transportation networks. Proponents of the argument have suggested that color space photographs of the resolution obtained with Hasselblad 80 mm lenses (about 300 feet) contain enough useful information to update the extensions of major U. S. highways. The present study systematically documents for the Dallas-Fort Worth area the potential of such space photography in detecting, and to a lesser degree identifying, the existing road networks. Color separation plates and an enlargement of the color photograph were produced and all visible roads traced onto transparencies for study. Major roads and roads under construction were the most visible while lower class roads and roads in urban areas had the poorest return. Road width and classification were found to be the major determinant in visibility, varying from 100 per cent visible for divided highways to 15 per cent visible of bladed earth roads. In summary, space photographs of this resolution proved to be difficult to use for accurate road delineation. Only super highways in rural areas with the greatest road-width were completely identifiable, the width being about 1/3 that of the resolution cell.

Noise and Sonic Boom Impact Technology. Initial Development of an Assessment System for Aircraft Noise (ASAN). Volume 3. Technical Description

DTIC Science & Technology

1989-06-01

field width, it will be padded on the left (or right, if the left adjustment indicator has been given) to make up the field width. The padding character...is blank (space) normally, and zero if the field width was specified with a leading zero (this zero does not imply an octal field width). 25 " a...unsigned octal notation (without a leading zero ). ’x The argument is coverted to unsigned hexadecimal notation (without a leading Ox). * u The argument is

On the origin of the phase-space diffusion limit in (dis)ordered protein aggregation

NASA Astrophysics Data System (ADS)

Gadomski, A.; Siódmiak, J.; Santamaría-Holek, I.

2013-08-01

Derivation of a phase-space diffusion limit (D-L) allows to obtain a useful formula for a characteristic width of the macroion-channeling filter, controlling model (dis)ordered protein aggregations in a non-ideal aqueous solution. The channel’s width is estimated at the order of an inner half-width of the Stern-type double layer circumventing the growing object and depends in turn on an interplay of the local thermal and electrostatic conditions. The interfacial channeling effect manifests at the edge of biomolecular hydration-duration dependent (non)Markovianity of the system. The interface vs. solution aggregation late-time dynamics are discussed in such local (non)isothermal context with the aim to suggest their experimental assessment.

Evaluation of arch width variations among different skeletal patterns in South Indian population

PubMed Central

Prasad, Mandava; Kannampallil, Senny Thomas; Talapaneni, Ashok Kumar; George, Suja Ani; Shetty, Sharath Kumar

2013-01-01

Background: Anterior cranial base can be taken as a reference line (SN) to determine the steepness of mandibular plane. Subjects with high mandibular plane angle tend to have a long face and one with low MP-SN angle has a shorter face. Objective: This study was done to investigate if dental arch widths correlated with vertical facial types and if there are any differences in arch widths between untreated male and female adults in South Indian population. Materials and Methods: Lateral cephalogram and dental casts were obtained from 180 untreated South Indian adults (90 males and 90 females) above 18 year old with no cross bite, minimal crowding and spacing. The angle between the anterior cranial base and the mandibular plane was measured on lateral cephalogram of each patient. Dental casts were used to obtain comprehensive dental measurements including maxillary and mandibular inter canine, inter premolar and inter molar widths, as well as amount of crowding or spacing. Results: The results showed that male arch widths were significantly larger than those of females (P < 0.05) and there was a significant decrease in inter arch width as the MP-SN angle increased in untreated adult South Indian population. The results obtained in our study when compared with studies done in other population groups showed that there is difference in inter arch widths according to ethnicity and race. Conclusion: It was concluded that the dental arch width is associated with gender, race and vertical facial morphology. Thus using individualized arch wires according to each patient's pre treatment arch form and width is suggested during orthodontic treatment. PMID:23633842

Global kinetic simulations of neoclassical toroidal viscosity in low-collisional perturbed tokamak plasmas

NASA Astrophysics Data System (ADS)

Matsuoka, Seikichi; Idomura, Yasuhiro; Satake, Shinsuke

2017-10-01

The neoclassical toroidal viscosity (NTV) caused by a non-axisymmetric magnetic field perturbation is numerically studied using two global kinetic simulations with different numerical approaches. Both simulations reproduce similar collisionality ( νb*) dependencies over wide νb * ranges. It is demonstrated that resonant structures in the velocity space predicted by the conventional superbanana-plateau theory exist in the small banana width limit, while the resonances diminish when the banana width becomes large. It is also found that fine scale structures are generated in the velocity space as νb* decreases in the large banana width simulations, leading to the νb* -dependency of the NTV. From the analyses of the particle orbit, it is found that the finite k∥ mode structure along the bounce motion appears owing to the finite orbit width, and it suffers from bounce phase mixing, suggesting the generation of the fine scale structures by the similar mechanism as the parallel phase mixing of passing particles.

Applicability of the Moyers' Probability Tables in Adolescents with Different Facial Biotypes

PubMed Central

Carrillo, Jorge J. Pavani; Rubial, Maria C.; Albornoz, Cristina; Villalba, Silvina; Damiani, Patricia; de Cravero, Marta Rugani

2017-01-01

Introduction: The Moyers’ probability tables are used in mixed dentition analysis to estimate the extent of space required for the alignment of canines and premolars, by correlating the mesiodistal size of lower incisors with the size of permanent canines and premolars. Objective: This study intended to evaluate the applicability of the Moyer's probability tables for predicting the mesiodistal space needed for the correct location of premolars and permanent canines non-erupted, in adolescents of the city of Cordoba, Argentina, who show different facial biotypes. Materials and Methods: Models and tele-radiographies of 478 adolescents of both genders from 10 to 15 years of age were analyzed. The tele-radiographies were measured manually in order to determine the facial biotype. The models were scanned with a gauged scanner (HP 3670) and measured by using Image Pro Plus 4.5 software. Results: According to this study, the comparison between the Moyer´s probability table, and the table created at the National University of Córdoba (UNC) (at 95%, 75%, and 50%) shows that, in both tables, a higher value of mesiodistal width of lower incisors corresponds to a bigger difference in the space needed for permanent canines and premolars; being the need for space for permanents canines and premolars bigger in the UNC´s table. On the other hand, when contrasting the values of mesiodistal space for permanent canines and premolars associated with each facial biotype, the discrepancies between groups were not statistically significant (P >0.05). However, we found differences in the size of the space required according to the mesiodistal width range of the lower incisors for each biotype: a) The comparison of lower-range values, with a mesialdistal width of lower incisors less than 22 mm, the space required for permanent canines and premolars resulted smaller in patients with dolichofacial biotype than in patients with mesofacial and braquifacial biotypes. The latter biotypes have meager differences between them. b) The comparison of mid-range values, with a mesialdistal width of lower incisors from 22 to 25 millimeters, shows that the values of required alignment space are similar in the three facial biotypes. c) Finally, the comparison of upper range values, with a mesialdistal width of lower incisors greater than 25 millimeters, indicates that the space required for dolichofacial biotypes tends to be higher than in mesofacial and brachyfacial biotypes. Conclusion: The Moyer´s probability tables should be created to meet the needs of the population under study, with no consideration of patients’ facial biotypes. PMID:28567145

Dielectric image line groove antennas for millimeterwaves

NASA Astrophysics Data System (ADS)

Solbach, K.; Wolff, I.

Grooves in the ground plane of dielectric image lines are proposed as a new radiating structure. A figure is included showing the proposed groove structure as a discontinuity in a dielectric image line. A wave incident on the dielectric image line is partly reflected by the discontinuity, partly transmitted across the groove, and partly radiated into space above the line. In a travelling-wave antenna, a number of grooves are arranged below a dielectric guide, with spacings around one guide wavelength to produce a beam in the upper half space. A prescribed aperture distribution can be effected by tapering the series radiation resistance of the grooves. This can be done by adjusting the depths of the grooves with a constant width or by varying the widths of the grooves with a constant depth. Attention is also given to circular grooves. Here, the widths of the holes are chosen so that they can be considered as waveguides operating far below the cut-off frequency of the fundamental circular waveguide mode.

Segmentation of hand radiographs using fast marching methods

NASA Astrophysics Data System (ADS)

Chen, Hong; Novak, Carol L.

2006-03-01

Rheumatoid Arthritis is one of the most common chronic diseases. Joint space width in hand radiographs is evaluated to assess joint damage in order to monitor progression of disease and response to treatment. Manual measurement of joint space width is time-consuming and highly prone to inter- and intra-observer variation. We propose a method for automatic extraction of finger bone boundaries using fast marching methods for quantitative evaluation of joint space width. The proposed algorithm includes two stages: location of hand joints followed by extraction of bone boundaries. By setting the propagation speed of the wave front as a function of image intensity values, the fast marching algorithm extracts the skeleton of the hands, in which each branch corresponds to a finger. The finger joint locations are then determined by using the image gradients along the skeletal branches. In order to extract bone boundaries at joints, the gradient magnitudes are utilized for setting the propagation speed, and the gradient phases are used for discriminating the boundaries of adjacent bones. The bone boundaries are detected by searching for the fastest paths from one side of each joint to the other side. Finally, joint space width is computed based on the extracted upper and lower bone boundaries. The algorithm was evaluated on a test set of 8 two-hand radiographs, including images from healthy patients and from patients suffering from arthritis, gout and psoriasis. Using our method, 97% of 208 joints were accurately located and 89% of 416 bone boundaries were correctly extracted.

Convection-Diffusion Layer in an "Open Space" for Local Surface Treatment and Microfabrication using a Four-Aperture Microchemical Pen.

PubMed

Mao, Sifeng; Zhang, Yong; Zhang, Weifei; Zeng, Hulie; Nakajima, Hizuru; Lin, Jin-Ming; Uchiyama, Katsumi

2017-09-06

A four-aperture microchemical pen was used to produce a stable convection-diffusion layer in an "open space" for microreactions and microfabrication. The process represents a new method for microreactions and microfabrication in a convection-diffusion layer. To prove the concept of a convection-diffusion layer in an "open space", bovine serum albumin was labeled with 4-fluoro-7-nitro-2,1,3-benzoxadiazole to confirm that the small convection-diffusion layer was effective for local surface treatment. To demonstrate the potential for microfabrication, silver patterns were fabricated on a glass surface with a convection-diffusion layer by using the silver-mirror reaction. The widths of each silver pattern could be easily controlled from 10 to 60 μm. Patterned silver lines with uniform widths or gradient widths were prepared. This is the first proof of concept study of a convection-diffusion layer in an "open space" used in local surface treatment and microfabrication on a surface. The microchemical pen represents a potential method for the region-selective microtreatment of tissues, cells, and other biological interfaces. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Optimized Design of Spacer in Electrodialyzer Using CFD Simulation Method

NASA Astrophysics Data System (ADS)

Jia, Yuxiang; Yan, Chunsheng; Chen, Lijun; Hu, Yangdong

2018-06-01

In this study, the effects of length-width ratio and diversion trench of the spacer on the fluid flow behavior in an electrodialyzer have been investigated through CFD simulation method. The relevant information, including the pressure drop, velocity vector distribution and shear stress distribution, demonstrates the importance of optimized design of the spacer in an electrodialysis process. The results show width of the diversion trench has a great effect on the fluid flow compared with length. Increase of the diversion trench width could strength the fluid flow, but also increase the pressure drop. Secondly, the dead zone of the fluid flow decreases with increase of length-width ratio of the spacer, but the pressure drop increases with the increase of length-width ratio of the spacer. So the appropriate length-width ratio of the space should be moderate.

Computer re-sampling for demographically representative user populations in anthropometry: a case of doorway and clear floor space widths.

PubMed

Paquet, Victor; Joseph, Caroline; D'Souza, Clive

2012-01-01

Anthropometric studies typically require a large number of individuals that are selected in a manner so that demographic characteristics that impact body size and function are proportionally representative of a user population. This sampling approach does not allow for an efficient characterization of the distribution of body sizes and functions of sub-groups within a population and the demographic characteristics of user populations can often change with time, limiting the application of the anthropometric data in design. The objective of this study is to demonstrate how demographically representative user populations can be developed from samples that are not proportionally representative in order to improve the application of anthropometric data in design. An engineering anthropometry problem of door width and clear floor space width is used to illustrate the value of the approach.

Comparative analysis of sustainable value distribution for stakeholders in the mining industry

NASA Astrophysics Data System (ADS)

Lorenc, Sylwia; Kustra, Arkadiusz

2018-01-01

The objective of this article is the analysis and comparison of the value distribution process that takes place in enterprises for stakeholders. The following coal mining enterprises are subject of this work: JSW S.A., KGHM S.A., and LW Bogdanka S.A, for which the directions of value distribution in the years 2011-2016 were presented. The article defines the main groups of the partnerships' stakeholders, such as the owners, staff, suppliers, equity providers, the country budget and the local governments' budgets. The sustainable value benchmark was defined as the benefits received by the stakeholders through the allocation of financial surplus. The value defined for the abovementioned stakeholders was assessed according to the Free Cash Flow (FCF) methodology.

Geometric methods for estimating representative sidewalk widths applied to Vienna's streetscape surfaces database

NASA Astrophysics Data System (ADS)

Brezina, Tadej; Graser, Anita; Leth, Ulrich

2017-04-01

Space, and in particular public space for movement and leisure, is a valuable and scarce resource, especially in today's growing urban centres. The distribution and absolute amount of urban space—especially the provision of sufficient pedestrian areas, such as sidewalks—is considered crucial for shaping living and mobility options as well as transport choices. Ubiquitous urban data collection and today's IT capabilities offer new possibilities for providing a relation-preserving overview and for keeping track of infrastructure changes. This paper presents three novel methods for estimating representative sidewalk widths and applies them to the official Viennese streetscape surface database. The first two methods use individual pedestrian area polygons and their geometrical representations of minimum circumscribing and maximum inscribing circles to derive a representative width of these individual surfaces. The third method utilizes aggregated pedestrian areas within the buffered street axis and results in a representative width for the corresponding road axis segment. Results are displayed as city-wide means in a 500 by 500 m grid and spatial autocorrelation based on Moran's I is studied. We also compare the results between methods as well as to previous research, existing databases and guideline requirements on sidewalk widths. Finally, we discuss possible applications of these methods for monitoring and regression analysis and suggest future methodological improvements for increased accuracy.

Investigation on Selective Laser Melting AlSi10Mg Cellular Lattice Strut: Molten Pool Morphology, Surface Roughness and Dimensional Accuracy

PubMed Central

Han, Xuesong; Zhu, Haihong; Nie, Xiaojia; Wang, Guoqing; Zeng, Xiaoyan

2018-01-01

AlSi10Mg inclined struts with angle of 45° were fabricated by selective laser melting (SLM) using different scanning speed and hatch spacing to gain insight into the evolution of the molten pool morphology, surface roughness, and dimensional accuracy. The results show that the average width and depth of the molten pool, the lower surface roughness and dimensional deviation decrease with the increase of scanning speed and hatch spacing. The upper surface roughness is found to be almost constant under different processing parameters. The width and depth of the molten pool on powder-supported zone are larger than that of the molten pool on the solid-supported zone, while the width changes more significantly than that of depth. However, if the scanning speed is high enough, the width and depth of the molten pool and the lower surface roughness almost keep constant as the density is still high. Therefore, high dimensional accuracy and density as well as good surface quality can be achieved simultaneously by using high scanning speed during SLMed cellular lattice strut. PMID:29518900

Flow measurements in two cambered vane diffusers with different passage widths

NASA Astrophysics Data System (ADS)

Stein, W.; Rautenberg, M.

1985-03-01

To investigate the influence of the vaneless space between impeller exit and the diffuser vanes, detailed flow measurements in two diffusers with the same vane geometry but different passage width are compared. The three-dimensional character of the flow changes between impeller exit and the entry to the two dimensional vanes depending on the shape of the shroud. After initial measurements with a constant area vaneless space, the width of the vaned diffuser was later on reduced by 10 percent. The compressor maps show increases in overall pressure rise and efficiency with the width reduction. To get further details of the flow field, measurements of the static pressure distribution at hub and shroud have been performed at several operation points for both diffusers. At the same points, the flow angle and total pressure distribution between hub and shroud upstream and downstream of the vanes have been measured with probes. The maximum efficiency of the narrow diffuser is nearly 2 percent higher than for the wide diffuser. The measurements give further details to explain this improvement.

ELECTRON MICROSCOPE AND X-RAY DIFFRACTION STUDIES ON A HOMOLOGOUS SERIES OF SATURATED PHOSPHATIDYLCHOLINES.

PubMed

ELBERS, P F; VERVERGAERT, P H

1965-05-01

Three homologous saturated phosphatidylcholines were studied by electron microscopy after tricomplex fixation. The results are compared with those obtained by x-ray diffraction analysis of the same and some other homologous compounds, in the dry crystalline state and after tricomplex fixation. By electron microscopy alternating dark and light bands are observed which are likely to correspond to phosphatide double layers. X-Ray diffraction reveals the presence of lamellar structures of regular spacing. The layer spacings obtained by both methods are in good agreement. From the electron micrographs the width of the polar parts of the double layers can be derived directly. The width of the carboxylglycerylphosphorylcholine moiety of the layers is found by extrapolating the x-ray diffraction data to zero chain length of the fatty acids. When from this width the contribution of the carboxylglyceryl part of the molecules is subtracted, again we find good agreement with the electron microscope measurements. An attempt has been made to account for the different layer spacings measured in terms of orientation of the molecules within the double layers.

Receiver design, performance analysis, and evaluation for space-borne laser altimeters and space-to-space laser ranging systems

NASA Technical Reports Server (NTRS)

Davidson, Frederic M.; Sun, Xiaoli; Field, Christopher T.

1995-01-01

Laser altimeters measure the time of flight of the laser pulses to determine the range of the target. The simplest altimeter receiver consists of a photodetector followed by a leading edge detector. A time interval unit (TIU) measures the time from the transmitted laser pulse to the leading edge of the received pulse as it crosses a preset threshold. However, the ranging error of this simple detection scheme depends on the received, pulse amplitude, pulse shape, and the threshold. In practice, the pulse shape and the amplitude are determined by the target target characteristics which has to be assumed unknown prior to the measurement. The ranging error can be improved if one also measures the pulse width and use the average of the leading and trailing edges (half pulse width) as the pulse arrival time. The ranging error becomes independent of the received pulse amplitude and the pulse width as long as the pulse shape is symmetric. The pulse width also gives the slope of the target. The ultimate detection scheme is to digitize the received waveform and calculate the centroid as the pulse arrival time. The centroid detection always gives unbiased measurement even for asymmetric pulses. In this report, we analyze the laser altimeter ranging errors for these three detection schemes using the Mars Orbital Laser Altimeter (MOLA) as an example.

Screw-fed pump system

DOEpatents

Sprouse, Kenneth M

2014-11-25

A pump system includes a pump that includes a first belt and a second belt that are spaced apart from each other to provide generally straight sides of a passage there between. There is an inlet at one end of the passage and an outlet at an opposite end of the passage, with a passage length that extends between the inlet and the outlet. The passage defines a gap distance in a width direction between the straight sides at the passage inlet. A hopper includes an interior space that terminates at a mouth at the passage inlet. At least one screw is located within the interior space of the hopper and includes a screw diameter in the width direction that is less than or equal to the gap distance.

Effects of aperture averaging and beam width on a partially coherent Gaussian beam over free-space optical links with turbulence and pointing errors.

PubMed

Lee, It Ee; Ghassemlooy, Zabih; Ng, Wai Pang; Khalighi, Mohammad-Ali; Liaw, Shien-Kuei

2016-01-01

Joint effects of aperture averaging and beam width on the performance of free-space optical communication links, under the impairments of atmospheric loss, turbulence, and pointing errors (PEs), are investigated from an information theory perspective. The propagation of a spatially partially coherent Gaussian-beam wave through a random turbulent medium is characterized, taking into account the diverging and focusing properties of the optical beam as well as the scintillation and beam wander effects. Results show that a noticeable improvement in the average channel capacity can be achieved with an enlarged receiver aperture in the moderate-to-strong turbulence regime, even without knowledge of the channel state information. In particular, it is observed that the optimum beam width can be reduced to improve the channel capacity, albeit the presence of scintillation and PEs, given that either one or both of these adverse effects are least dominant. We show that, under strong turbulence conditions, the beam width increases linearly with the Rytov variance for a relatively smaller PE loss but changes exponentially with steeper increments for higher PE losses. Our findings conclude that the optimal beam width is dependent on the combined effects of turbulence and PEs, and this parameter should be adjusted according to the varying atmospheric channel conditions. Therefore, we demonstrate that the maximum channel capacity is best achieved through the introduction of a larger receiver aperture and a beam-width optimization technique.

Gas Cromatography In Solar System Exploration:decoding Complex Chromatograms Recovered From Space Missions

NASA Astrophysics Data System (ADS)

Pietrogrande, M. C.; Tellini, I.; Dondi, F.; Felinger, A.; Sternberg, R.; Szopa, C.; Vidal-Madjar, C.

GC plays a predominant role in solar system explorations: it has been applied to space research related to exobiology: i.e., Cassini-Huygens mission devoted to characterize chemical composition of TitanSs atmosphere [2], Rosetta mission to investigate the nucleus of comet p/Wirtamen (COSAC experiments) [1]. GC analysis of planetary atmosphere is a difficult analytical task because of the unknown and low level of an- alytes present in the sample, the high degree of automatization required, the strong constraints due to the flight (short analysis time, low power consumption, high accu- racy and reliability under extreme space conditions). In these circumstances the use of a signal processing procedure is practically mandatory to efficiently extract useful in- formation from the raw chromatogram ­ i.e. to decode the complex chromatogram to determine the number of components, the separation efficiency and the retention pat- tern. In this work a chemometric approach based on the Fourier analysis is applied to complex chromatograms related to space research: from the autocovariance function (ACVF) computed on the digitized chromatogram, the chromatographic parameters ­ number of components, peak shape parameters, retention pattern ­ can be estimated [3-7]. The procedure, originally developed for constant peak width [3], was extended to variable peak width [4], in order to describe chromatograms obtained in isother- mal conditions, i.e., analysis condition compatible with space flight constraints. The chemometric procedure was applied to chromatograms of standard mixtures repre- sentative of planetary atmospheres ­ hydrocarbons and oxygenated compounds with carbon atom number ranging from 2 to 8 ­ obtained in flight simulating conditions ­ isothermal or pseudo-isothermal conditions. Both the simplified graphic procedure, based on the assumption of constant peak width [3], and the complete approach de- veloped for variable peak width [4], were applied and the results compared. Also an independent procedure was used to estimate peak width, in order to validate the ob- tained results. The number of components present in the mixture and the peak width (related to separation efficiency) can be accurately estimated for the experimental chromatograms. Such information are useful to interpret data recovered from space 1 missions and to select the optimal analysis conditions compatible with flight con- straints. 1. C. Szopa et al., J. Chromatogr. A 2000, 904, 73. 2. M. C. Pietrogrande et al., J. Chromatogr. A, in press. 3. A. Felinger et al, Anal. Chem., 1990, 62, 1854. 4. A. Felinger et al, Anal. Chem., 1991, 63, 2627. 5. M. C. Pietrogrande et al., J. High Resol. Chromatogr. 1996, 19, 327. 6. F. Dondi et al, Chromatographia, 1997, 45, 435. 7. A. Felinger, M.C. Pietrogrande, Anal. Chem., 2001, 73, 618A. 2

Fine pattern replication on 10 x 10-mm exposure area using ETS-1 laboratory tool in HIT

NASA Astrophysics Data System (ADS)

Hamamoto, K.; Watanabe, Takeo; Hada, Hideo; Komano, Hiroshi; Kishimura, Shinji; Okazaki, Shinji; Kinoshita, Hiroo

2002-07-01

Utilizing ETS-1 laboratory tool in Himeji Institute of Technology (HIT), as for the fine pattern replicated by using the Cr mask in static exposure, it is replicated in the exposure area of 10 mm by 2 mm in size that the line and space pattern width of 60 nm, the isolated line pattern width of 40 nm, and hole pattern width of 150 nm. According to the synchronous scanning of the mass and wafer with EUVL laboratory tool with reduction optical system which consisted of three-aspherical-mirror in the NewSUBARU facilities succeeded in the line of 60 nm and the space pattern formation in the exposure region of 10mm by 10mm. From the result of exposure characteristics for positive- tone resist for KrF and EB, KrF chemically amplified resist has better characteristics than EB chemically amplified resist.

The rate of decline of joint space width in patients with osteoarthritis of the knee: a systematic review and meta-analysis of randomized placebo-controlled trials of chondroitin sulfate .

PubMed

Hochberg, Marc C; Zhan, Min; Langenberg, Patricia

2008-11-01

Chondroitin sulfate has been shown to relieve pain and improve functional limitation in patients with osteoarthritis (OA) of the knee in numerous clinical trials and meta-analyses. Its role as a potential structure-modifying drug for knee OA, however, remains controversial. To perform a meta-analysis of randomized double-blind placebo-controlled clinical trials to assess the efficacy of chondroitin sulfate as a structure-modifying drug for knee OA. A Medline search was conducted from 1996 through 2007 and five articles that reported results from three trials were identified; one additional trial was identified through review of presentations at annual rheumatology meetings. There was no evidence of heterogeneity across the trials and results were pooled using a fixed effects meta-analysis. Pooled results demonstrated a small significant effect of chondroitin sulfate on the reduction in rate of decline in minimum joint space width of 0.07 mm/year (95% CI 0.03, 0.10) that corresponded to an effect size of 0.26 (95% CI 0.14, 0.38) (p < 0.0001). This result was robust in sensitivity analyses. The individual studies included in the meta-analysis varied in the number of patients enrolled and the techniques used to acquire knee radiographs and to measure joint space width. These results demonstrate that chondroitin sulfate is effective for reducing the rate of decline in minimum joint space width in patients with OA of the knee. Chondroitin sulfate may have a role as a structure-modifying agent in the management of patients with knee OA.

Anomalous width variations for ion acoustic rarefactive solitary waves in a warm ion plasma with two electron temperatures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ghosh, S.S.; Sekar Iyengar, A.N.

1997-09-01

Anomalous width{endash}amplitude variations were observed in large amplitude rarefactive solitary waves which show increasing width with increasing amplitude, contrasting the usual reciprocal relation between the square of the width and the amplitude, beyond a certain value of the plasma parameters [S. S. Ghosh, K. K. Ghosh, and A. N. Sekar Iyengar, Phys. Plasmas, {bold 3}, 3939 (1996)]. For the limiting maximum amplitude, the {open_quotes}increasing width{close_quotes} solitary wave tends to a double layer-like solution. The overall variation was found to depend crucially on the specific parameter space. From a detailed investigation of the above behavior, a plausible physical explanation has beenmore » presented for such increases in the width. It is found that the ions{close_quote} initial kinetic energies and the cold electron concentration within the perturbed region play a significant role in determining the observed width{endash}amplitude variation. This contradicts the investigation of Sayal, Yadav, and Sharma [Phys. Scr. {bold 47}, 576 (1993)]. {copyright} {ital 1997 American Institute of Physics.}« less

Substrate Oxide Layer Thickness Optimization for a Dual-Width Plasmonic Grating for Surface-Enhanced Raman Spectroscopy (SERS) Biosensor Applications

PubMed Central

Bauman, Stephen J.; Brawley, Zachary T.; Darweesh, Ahmad A.; Herzog, Joseph B.

2017-01-01

This work investigates a new design for a plasmonic SERS biosensor via computational electromagnetic models. It utilizes a dual-width plasmonic grating design, which has two different metallic widths per grating period. These types of plasmonic gratings have shown larger optical enhancement than standard single-width gratings. The new structures have additional increased enhancement when the spacing between the metal decreases to sub-10 nm dimensions. This work integrates an oxide layer to improve the enhancement even further by carefully studying the effects of the substrate oxide thickness on the enhancement and reports ideal substrate parameters. The combined effects of varying the substrate and the grating geometry are studied to fully optimize the device’s enhancement for SERS biosensing and other plasmonic applications. The work reports the ideal widths and substrate thickness for both a standard and a dual-width plasmonic grating SERS biosensor. The ideal geometry, comprising a dual-width grating structure atop an optimal SiO2 layer thickness, improves the enhancement by 800%, as compared to non-optimized structures with a single-width grating and a non-optimal oxide thickness. PMID:28665308

Fleet Mooring Leg Design Program Documentation. Volume 7. Source Listings: Table and Graphs.

DTIC Science & Technology

1982-12-01

cop3b ,wgt3. asgt3b, a s)lip,fr ict , cImp3, & scopi, Wgtl, 6 n&sep, & plx,plzpld, N 00 & p2x ,p2z ,P2d, & p3x p3z ,p3d, & hioad~hdir, & rbuoy ,xbuoy...XP-XPOINTl I( YP-YPOINT (Ii IF(JSW ED 1) GO TO 12S DELWX-WXU-WXL DELWY-WYU-WYL XP-(XPNT(I 1*OELWXI)/_,iLVX YP-(YPNT(I 3SOELWYJ/OELVY N’ 12S XF- ICT *XP...0) xcoord-xa a gym -S wrifelul .8) xcoord,hsym,isyn ws- 1 Soo continue * gYM -0 if (isg eq k) isym-S if (k ne 11 goto S0 xcoord-xm an gala 900 continue

Thermal barrier pressure seal. [shielding junctions between spacecraft control surfaces and structures

NASA Technical Reports Server (NTRS)

Bellavia, J., Jr.; Kane, J. O. (Inventor)

1980-01-01

An apparatus is described for providing thermal and pressure sealing in an elongated space of varying width between adjacent surface of two members. The apparatus is mounted for at least limited lateral movement between the members and may comprise: an elongated support attached to one of the adjacent surfaces; a second elongated support member attached to the other of the adjacent surfaces, and an elongated seal member sandwiched between the first and second support members. In its non-deformed state, the elongated seal member may be substantially cylindrical but capable of deformation to accommodate limited lateral movement between the adjacent surfaces and varying widths of the space.

Interference effect on a heavy Higgs resonance signal in the γ γ and Z Z channels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Song, Jeonghyeon; Yoon, Yeo Woong; Jung, Sunghoon

2016-03-24

The resonance-continuum interference is usually neglected when the width of a resonance is small compared to the resonance mass. We reexamine this standard by studying the interference effects in high-resolution decay channels, γγ and ZZ, of the heavy Higgs boson H in nearly aligned two-Higgs-doublet models. For the H with a sub-percent width-to-mass ratio, we find that, in the parameter space where the LHC 14 TeV ZZ resonance search can be sensitive, the interference effects can modify the ZZ signal rate by O(10)% and the exclusion reach by O(10) GeV. In other parameter space where the ZZ or γγ signalmore » rate is smaller, the LHC 14 TeV reach is absent, but a resonance shape can be much more dramatically changed. In particular, the γγ signal rate can change by O(100)%. Relevant to such parameter space, we suggest variables that can characterize a general resonance shape. Furthermore, we also illustrate the relevance of the width on the interference by adding nonstandard decay modes of the heavy Higgs boson.« less

Location specific solidification microstructure control in electron beam melting of Ti-6Al-4V

DOE Office of Scientific and Technical Information (OSTI.GOV)

Narra, Sneha P.; Cunningham, Ross; Beuth, Jack

Relationships between prior beta grain size in solidified Ti-6Al-4V and melting process parameters in the Electron Beam Melting (EBM) process are investigated. Samples are built by varying a machine-dependent proprietary speed function to cover the process space. Optical microscopy is used to measure prior beta grain widths and assess the number of prior beta grains present in a melt pool in the raster region of the build. Despite the complicated evolution of beta grain sizes, the beta grain width scales with melt pool width. The resulting understanding of the relationship between primary machine variables and prior beta grain widths ismore » a key step toward enabling the location specific control of as-built microstructure in the EBM process. Control of grain width in separate specimens and within a single specimen is demonstrated.« less

Effects of milking stall dimensions on behavior of dairy cows during milking in different milking parlor types.

PubMed

Gómez, Y; Terranova, M; Zähner, M; Hillmann, E; Savary, P

2017-02-01

Dairy cow body size has increased over time because of breeding selection for higher milk yield, but milking stall dimensions have never been adjusted and are based on the practical experience of milking-machine manufacturers and advisory institutions. Narrow, limited milking stall dimensions might lead to behavioral changes during milking due to lack of comfort. The aim of this study was to examine the current space allowance in milking stalls on dairy farms and assess the effect of space allowance on cow behavior during milking. On 15 Swiss dairy farms, we measured clear milking stall dimensions and cow body dimensions. We calculated space ratios for length (SR length ) and width (SR width ) by dividing the milking stall length or width by cow body length or belly width, respectively. When the space ratio was >1, we assumed that the body length or width of cow was smaller than the milking stall length or width. On each farm, 10 healthy cows were chosen for behavioral observation during 1 evening milking. We recorded rumination, elimination, and latency to enter the milking stall by direct observation. Hind leg activity was recorded using acceleration loggers. Data were analyzed using general linear mixed-effects models with farm as a random effect. Due to a strong collinearity between SR width and SR length , we chose SR length for further analysis, because it is based on skeletal characteristics. The SR length was smallest in side-by-side parlors (1.07 ± 0.01) and largest in tandem parlors (1.18 ± 0.01). More cows had a tendency to ruminate with increasing SR length (odds ratio: 1.8). None of hind leg activity, maximum peaks of hind leg accelerations, or latency to enter the milking stall were significantly affected by SR length . Latency to enter the milking stall was longer for group milking parlors (side-by-side: 44.0 ± 3.2 s; herringbone: 34.3 ± 2.9 s) than for tandem parlors (19.0 ± 2.7 s). Milking parlor type had no effect on hind leg activity, maximum peaks of hind leg accelerations or rumination. The SR length affected rumination behavior to some extent, indicating that cow comfort was positively affected by larger milking stall length. Because cow comfort is important for good milking performance, further investigations of milking stall dimensions for cow comfort and thus welfare are needed. Furthermore, the results showed that parlor type affected cow behavior, irrespective of SR length , making future research necessary to identify the factors leading to this effect of parlor type. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Surgical anatomy of the middle premasseter space and its application in sub-SMAS face lift surgery.

PubMed

Mendelson, Bryan C; Wong, Chin-Ho

2013-07-01

The premasseter space is a recognized, sub-superficial musculoaponeurotic system (SMAS) soft-tissue space overlying the lower masseter immediately anterior to the parotid. The performance, safety, and effectiveness of composite face lifts are enhanced when the space is used. This has drawn attention to the need for better understanding of the premasseter anatomy above the space. The anatomy of the upper premasseter region was investigated in 20 fresh cadaver dissections as well as intraoperatively in hundreds of composite face lifts. A small, transverse, rectangular soft-tissue space overlies the upper masseter and was named the middle premasseter space. The space (transverse width, 25 to 28 mm; vertical width, 10 mm) is separated from the originally described (lower) premasseter space by a double membrane. It is a safe space between the upper and lower buccal trunks of the facial nerve, which are immediately outside the space and separated from it by the respective upper and lower boundary membranes. The parotid duct immediately beneath the floor of the space usually underlies the upper boundary membrane. The middle premasseter space is significant, as it is the center of the key anatomy immediately cephalad to the lower premasseter space. When used in composite face lifts, the space provides predictable sub-SMAS dissection between the buccal trunks of the facial nerve to the mobile area beyond the anterior border of the masseter where the SMAS overlies the buccal fat pad.

Orthodontic space closure without contralateral extraction through mesial movement of lower molars in patients with aplastic lower second premolars.

PubMed

Zimmer, B; Guitard, Y

2001-09-01

A method is presented that allows unilateral space closure in patients with aplastic lower second premolars. Based on a straight-wire appliance, space closure was achieved with a combination of "push mechanics" using the second molar as an anchorage unit and Class II "pull mechanics", thus avoiding the application of any distalizing force on the lower incisors. The results from 13 consecutively treated subjects (five boys, eight girls, mean age 12 years and 6 months) were analyzed. Complete bodily space closure was achieved in all 13 cases within a mean treatment time of 2 years and 7 months. The desired Angle Class III molar relationship of one premolar width (+/- 1/4 premolar width) on the aplastic side was successful in eleven patients, an additional 4.7 mm of space being created for the third molar on the aplastic side compared with the contralateral side (p < or = 0.01). However, adverse effects could be kept to a minimum, with no method-dependent side effects being recorded with regard to canine and molar relationships on the contralateral side, or to overbite, overjet, or upper and lower incisor inclination. The mean lower midline shift of 0.8 mm was in accordance with the mean distal canine relationship of 1/3 premolar width on the aplastic side. These results confirm that orthodontic space closure in cases of unilateral aplastic lower second premolars can be performed successfully with the presented treatment method without the need for additional premolar extractions, prosthodontic treatment or implants. Furthermore, the prognosis for the lower wisdom tooth on the aplastic side is improved.

Theoretical study of fabrication of line-and-space patterns with 7 nm quarter-pitch using electron beam lithography with chemically amplified resist process: III. Post exposure baking on quartz substrates

NASA Astrophysics Data System (ADS)

Kozawa, Takahiro

2015-09-01

Electron beam (EB) lithography is a key technology for the fabrication of photomasks for ArF immersion and extreme ultraviolet (EUV) lithography and molds for nanoimprint lithography. In this study, the temporal change in the chemical gradient of line-and-space patterns with a 7 nm quarter-pitch (7 nm space width and 21 nm line width) was calculated until it became constant, independently of postexposure baking (PEB) time, to clarify the feasibility of single nano patterning on quartz substrates using EB lithography with chemically amplified resist processes. When the quencher diffusion constant is the same as the acid diffusion constant, the maximum chemical gradient of the line-and-space pattern with a 7 nm quarter-pitch did not differ much from that with a 14 nm half-pitch under the condition described above. Also, from the viewpoint of process control, a low quencher diffusion constant is considered to be preferable for the fabrication of line-and-space patterns with a 7 nm quarter-pitch on quartz substrates.

Neutron resonance parameters of 6830Zn+n and statistical distributions of level spacings and widths

NASA Astrophysics Data System (ADS)

Garg, J. B.; Tikku, V. K.; Harvey, J. A.; Halperin, J.; Macklin, R. L.

1982-04-01

Discrete values of the parameters (E0, gΓn, Jπ, Γγ, etc.) of the resonances in the reaction 6830Zn + n have been determined from total cross section measurements from a few keV to 380 keV with a nominal resolution of 0.07 ns/m for the highest energy and from capture cross section measurements up to 130 keV using the pulsed neutron time-of-flight technique with a neutron burst width of 5 ns. The cross section data were analyzed to determine the parameters of the resonances using R-matrix multilevel codes. These results have provided values of average quantities as follows: S0=(2.01+/-0.34), S1=(0.56+/-0.05), S2=(0.2+/-0.1) in units of 10-4, D0=(5.56+/-0.43) keV and D1=(1.63+/-0.14) keV. From these measurements we have also determined the following average radiation widths: (Γ¯γ)l=0=(302+/-60) meV and (Γ¯γ)l=1=(157 +/-7) meV. The investigation of the statistical properties of neutron reduced widths and level spacings showed excellent agreement of the data with the Porter-Thomas distribution for s- and p-wave neutron widths and with the Dyson-Mehta Δ3 statistic and the Wigner distribution for the s-wave level spacing distribution. In addition, a correlation coefficient of ρ=0.50+/-0.10 between Γ0n and Γγ has been observed for s-wave resonances. The value of <σnγ> at (30+/-10) keV is 19.2 mb. NUCLEAR REACTIONS 3068Zn(n,n), 3068Zn(n,γ), E=few keV to 380, 130 keV, respectively. Measured total and capture cross sections versus neutron energy, deduced resonance parameters, E0, Jπ, gΓn, Γγ, S0, S1, S2, D0, D1.

Measurement of laser spot quality

NASA Technical Reports Server (NTRS)

Milster, T. D.; Treptau, J. P.

1991-01-01

Several ways of measuring spot quality are compared. We examine in detail various figures of merit such as full width at half maximum (FWHM), full width at 1/(e exp 2) maximum, Strehl ratio, and encircled energy. Our application is optical data storage, but results can be applied to other areas like space communications and high energy lasers. We found that the optimum figure of merit in many cases is Strehl ratio.

An experimental investigation on the requirement of roof height and sill width for car ingress and egress.

PubMed

Causse, Julien; Wang, Xuguang; Denninger, Lisa

2012-01-01

This study aimed at experimentally investigating the influence of roof height and sill width on car ingress/egress movements. The first uncomfortable (Ht1) and the lowest acceptable (Ht2) roof heights were obtained from 26 participants of three different stature groups thanks to a multi-adjustable vehicle mock-up. Both Ht1 and Ht2 were affected neither by stature nor by vehicle type. Only a difference of 45 mm between Ht1 and Ht2 was observed. Tall volunteers more flexed the trunk and neck than short persons thanks to a larger space available around the seat when the head passing under the roof. The vehicle type had almost no effect on upper body posture. The roof height only affected neck flexion. The sill width mainly imposed a lateral translation. Results demonstrated that an appropriate roof height should be determined carefully. A small change of 45 mm in roof height may lead to an unacceptable situation. The present study experimentally investigated the effects of roof height and sill width on car ingress and egress movements. Short females required almost the same roof height as tall males due to smaller space around the seat. The results would help to optimise car dimensions for improving car accessibility.

Resonance and decay phenomena lead to quantum mechanical time asymmetry

NASA Astrophysics Data System (ADS)

Bohm, A.; Bui, H. V.

2013-04-01

The states (Schrödinger picture) and observables (Heisenberg picture) in the standard quantum theory evolve symmetrically in time, given by the unitary group with time extending over -∞ < t < +∞. This time evolution is a mathematical consequence of the Hilbert space boundary condition for the dynamical differential equations. However, this unitary group evolution violates causality. Moreover, it does not solve an old puzzle of Wigner: How does one describe excited states of atoms which decay exponentially, and how is their lifetime τ related to the Lorentzian width Γ? These question can be answered if one replaces the Hilbert space boundary condition by new, Hardy space boundary conditions. These Hardy space boundary conditions allow for a distinction between states (prepared by a preparation apparatus) and observables (detected by a registration apparatus). The new Hardy space quantum theory is time asymmetric, i.e, the time evolution is given by the semigroup with t0 <= t < +∞, which predicts a finite "beginning of time" t0, where t0 is the ensemble of time at which each individual system has been prepared. The Hardy space axiom also leads to the new prediction: the width Γ and the lifetime τ are exactly related by τ = hslash/Γ.

Measurement of glomerulus diameter and Bowman's space width of renal albino rats.

PubMed

Kotyk, Taras; Dey, Nilanjan; Ashour, Amira S; Balas-Timar, Dana; Chakraborty, Sayan; Ashour, Ahmed S; Tavares, João Manuel R S

2016-04-01

Glomerulus diameter and Bowman's space width in renal microscopic images indicate various diseases. Therefore, the detection of the renal corpuscle and related objects is a key step in histopathological evaluation of renal microscopic images. However, the task of automatic glomeruli detection is challenging due to their wide intensity variation, besides the inconsistency in terms of shape and size of the glomeruli in the renal corpuscle. Here, a novel solution is proposed which includes the Particles Analyzer technique based on median filter for morphological image processing to detect the renal corpuscle objects. Afterwards, the glomerulus diameter and Bowman's space width are measured. The solution was tested with a dataset of 21 rats' renal corpuscle images acquired using light microscope. The experimental results proved that the proposed solution can detect the renal corpuscle and its objects efficiently. As well as, the proposed solution has the ability to manage any input images assuring its robustness to the deformations of the glomeruli even with the glomerular hypertrophy cases. Also, the results reported significant difference between the control and affected (due to ingested additional daily dose (14.6mg) of fructose) groups in terms of glomerulus diameter (97.40±19.02μm and 177.03±54.48μm, respectively). Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Theoretical study on effects of photodecomposable quenchers in line-and-space pattern fabrication with 7 nm quarter-pitch using chemically amplified electron beam resist process

NASA Astrophysics Data System (ADS)

Kozawa, Takahiro

2017-04-01

The line width roughness (LWR) is a significant issue in the development of chemically amplified resists. The increase in sensitizer concentration is inevitable for the suppression of LWR in the sub-10 nm fabrication. In this study, we investigated the effects of photodecomposable quenchers from the viewpoint of the excluded volume effect, assuming line-and-space patterns with 7 nm quarter-pitch (7 nm space width and 28 nm pitch). The pattern formation of chemically amplified electron beam resists with photodecomposable quenchers was calculated and compared with those with conventional quenchers. It was found that the sum of the concentrations of acid generators and quenchers (photodecomposable or conventional quenchers) can be reduced without decreasing the chemical gradient (an indicator of LWR) by using the photodecomposable quenchers. The photodecomposable quenchers are considered essential in the high-resolution fabrication.

3-T direct MR arthrography of the wrist: value of finger trap distraction to assess intrinsic ligament and triangular fibrocartilage complex tears.

PubMed

Cerny, Milena; Marlois, Romain; Theumann, Nicolas; Bollmann, Christof; Wehrli, Laurent; Richarme, Delphine; Meuli, Reto; Becce, Fabio

2013-10-01

To determine the value of applying finger trap distraction during direct MR arthrography of the wrist to assess intrinsic ligament and triangular fibrocartilage complex (TFCC) tears. Twenty consecutive patients were prospectively investigated by three-compartment wrist MR arthrography. Imaging was performed with 3-T scanners using a three-dimensional isotropic (0.4 mm) T1-weighted gradient-recalled echo sequence, with and without finger trap distraction (4 kg). In a blind and independent fashion, two musculoskeletal radiologists measured the width of the scapholunate (SL), lunotriquetral (LT) and ulna-TFC (UTFC) joint spaces. They evaluated the amount of contrast medium within these spaces using a four-point scale, and assessed SL, LT and TFCC tears, as well as the disruption of Gilula's carpal arcs. With finger trap distraction, both readers found a significant increase in width of the SL space (mean Δ = +0.1mm, p ≤ 0.040), and noticed more contrast medium therein (p ≤ 0.035). In contrast, the differences in width of the LT (mean Δ = +0.1 mm, p ≥ 0.057) and UTFC (mean Δ = 0mm, p ≥ 0.728) spaces, as well as the amount of contrast material within these spaces were not statistically significant (p = 0.607 and ≥ 0.157, respectively). Both readers detected more SL (Δ = +1, p = 0.157) and LT (Δ = +2, p = 0.223) tears, although statistical significance was not reached, and Gilula's carpal arcs were more frequently disrupted during finger trap distraction (Δ = +5, p = 0.025). The application of finger trap distraction during direct wrist MR arthrography may enhance both detection and characterisation of SL and LT ligament tears by widening the SL space and increasing the amount of contrast within the SL and LT joint spaces. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

Thirty years of anthropometric changes relevant to the width and depth of transportation seating spaces, present and future.

PubMed

Molenbroek, J F M; Albin, T J; Vink, P

2017-11-01

This paper reports the results of an investigation into changes in body shape anthropometry over the past several decades and discusses the impact of those changes on seating in transport, especially airliners. Changes in some body shape dimensions were confirmed in a sample of students at TU Delft; several of the changes, e.g. hip breadth, seated, are relevant to the ongoing design of seating. No change in buttock knee length was observed. The fit between current user anthropometry and current airline seat design, especially regarding seat width, was investigated. A comparison of the average current seat breadth with global anthropometric data suggests that accommodation may be problematic, with less than optimal width for passengers' shoulder and elbow widths. Copyright © 2017 Elsevier Ltd. All rights reserved.

Freedom Space for Rivers: A Sustainable Management Approach to Enhance River Resilience

NASA Astrophysics Data System (ADS)

Biron, Pascale M.; Buffin-Bélanger, Thomas; Larocque, Marie; Choné, Guénolé; Cloutier, Claude-André; Ouellet, Marie-Audray; Demers, Sylvio; Olsen, Taylor; Desjarlais, Claude; Eyquem, Joanna

2014-11-01

River systems are increasingly under stress and pressure from agriculture and urbanization in riparian zones, resulting in frequent engineering interventions such as bank stabilization or flood protection. This study provides guidelines for a more sustainable approach to river management based on hydrogeomorphology concepts applied to three contrasted rivers in Quebec (Canada). Mobility and flooding spaces are determined for the three rivers, and three levels of "freedom space" are subsequently defined based on the combination of the two spaces. The first level of freedom space includes very frequently flooded and highly mobile zones over the next 50 years, as well as riparian wetlands. It provides the minimum space for both fluvial and ecological functionality of the river system. On average for the three studied sites, this minimum space was approximately 1.7 times the channel width, but this minimum space corresponds to a highly variable width which must be determined from a thorough hydrogeomorphic assessment and cannot be predicted using a representative average. The second level includes space for floods of larger magnitude and provides for meanders to migrate freely over a longer time period. The last level of freedom space represents exceptional flood zones. We propose the freedom space concept to be implemented in current river management legislation because it promotes a sustainable way to manage river systems, and it increases their resilience to climate and land use changes in comparison with traditional river management approaches which are based on frequent and spatially restricted interventions.

Radiological findings for hip dysplasia at skeletal maturity. Validation of digital and manual measurement techniques.

PubMed

Engesæter, Ingvild Øvstebø; Laborie, Lene Bjerke; Lehmann, Trude Gundersen; Sera, Francesco; Fevang, Jonas; Pedersen, Douglas; Morcuende, José; Lie, Stein Atle; Engesæter, Lars Birger; Rosendahl, Karen

2012-07-01

To report on intra-observer, inter-observer, and inter-method reliability and agreement for radiological measurements used in the diagnosis of hip dysplasia at skeletal maturity, as obtained by a manual and a digital measurement technique. Pelvic radiographs from 95 participants (56 females) in a follow-up hip study of 18- to 19-year-old patients were included. Eleven radiological measurements relevant for hip dysplasia (Sharp's, Wiberg's, and Ogata's angles; acetabular roof angle of Tönnis; articulo-trochanteric distance; acetabular depth-width ratio; femoral head extrusion index; maximum teardrop width; and the joint space width in three different locations) were validated. Three observers measured the radiographs using both a digital measurement program and manually in AgfaWeb1000. Inter-method and inter- and intra-observer agreement were analyzed using the mean differences between the readings/readers, establishing the 95% limits of agreement. We also calculated the minimum detectable change and the intra-class correlation coefficient. Large variations among different radiological measurements were demonstrated. However, the variation was not related to the use of either the manual or digital measurement technique. For measurements with greater absolute values (Sharp's angle, femoral head extrusion index, and acetabular depth-width ratio) the inter- and intra-observer and inter-method agreements were better as compared to measurements with lower absolute values (acetabular roof angle, teardrop and joint space width). The inter- and intra-observer variation differs notably across different radiological measurements relevant for hip dysplasia at skeletal maturity, a fact that should be taken into account in clinical practice. The agreement between the manual and digital methods is good.

Personalized Progressive Addition Lenses: Correlation between Performance and Design.

PubMed

Forkel, Johanne; Reiniger, Jenny Lorén; Muschielok, Adam; Welk, Andrea; Seidemann, Anne; Baumbach, Peter

2017-02-01

A continuous set of personalized designs (design space) for progressive addition lenses (PALs) is investigated. The main goals are (1) to study how the subjects' perception of a personalized design depends on its position in the design space and (2) to compare the performance of personalized PALs to a conventional PAL with a fixed design. In a double-blind study, 51 subjects compared Rodenstock Impression FreeSign 3, which is a family of PALs with a continuously controllable personalized design, and Rodenstock Progressiv Life Free, which is a conventional PAL with a single fixed design. The positions and sizes of viewing zones and the softness of gradients of mean power and astigmatism of personalized lenses were customized to individual viewing preferences. These designs were represented as points in a design space comprising a continuum of PAL designs. Subjective ratings and experimental measurements were used to study viewing zone widths, blur gradient smoothness, amount of distortion, the feeling of safety during motion, and overall wearing comfort. (1) Far viewing zone width (experiments and ratings), near viewing zone width (experiments), blur gradient smoothness, and the amount of distortion (ratings) were significantly dependent on the position of the personalized lens design in the design space. This was consistent with the structure of the design space. (2) 82% of the subjects chose personalized lenses as their favorite. Most subjects reported higher wearing comfort and tolerability with personalized lenses than with conventional lenses. The designs of the tested personalized lenses were perceived by the subjects as intended. This is a prerequisite to the successful customization of PALs to individual wearing preferences. Possible reasons for the preference of the tested personalized lenses are the optimization with respect to individual wearing conditions and the personalization.

Boundary plasma heat flux width measurements for poloidal magnetic fields above 1 Tesla in the Alcator C-Mod tokamak

NASA Astrophysics Data System (ADS)

Brunner, Dan; Labombard, Brian; Kuang, Adam; Terry, Jim; Alcator C-Mod Team

2017-10-01

The boundary heat flux width, along with the total power flowing into the boundary, sets the power exhaust challenge for tokamaks. A multi-machine boundary heat flux width database found that the heat flux width in H-modes scaled inversely with poloidal magnetic field (Bp) and was independent of machine size. The maximum Bp in the database was 0.8 T, whereas the ITER 15 MA, Q =10 scenario will be 1.2 T. New measurements of the boundary heat flux width in Alcator C-Mod extend the international database to plasmas with Bp up to 1.3 T. C-Mod was the only experiment able to operate at ITER-level Bp. These new measurements are from over 300 plasma shots in L-, I-, and EDA H-modes spanning essentially the whole operating space in C-Mod. We find that the inverse-Bp dependence of the heat flux width in H-modes continues to ITER-level Bp, further reinforcing the empirical projection of 500 μm heat flux width for ITER. We find 50% scatter around the inverse-Bp scaling and are searching for the `hidden variables' causing this scatter. Supported by USDoE award DE-FC02-99ER54512.

Method of measuring the dc electric field and other tokamak parameters

DOEpatents

Fisch, Nathaniel J.; Kirtz, Arnold H.

1992-01-01

A method including externally imposing an impulsive momentum-space flux to perturb hot tokamak electrons thereby producing a transient synchrotron radiation signal, in frequency-time space, and the inference, using very fast algorithms, of plasma parameters including the effective ion charge state Z.sub.eff, the direction of the magnetic field, and the position and width in velocity space of the impulsive momentum-space flux, and, in particular, the dc toroidal electric field.

Adsorption behaviors of supercritical Lennard-Jones fluid in slit-like pores.

PubMed

Li, Yingfeng; Cui, Mengqi; Peng, Bo; Qin, Mingde

2018-05-18

Understanding the adsorption behaviors of supercritical fluid in confined space is pivotal for coupling the supercritical technology and the membrane separation technology. Based on grand canonical Monte Carlo simulations, the adsorption behaviors of a Lennard-Jones (LJ) fluid in slit-like pores at reduced temperatures over the critical temperature, T c *  = 1.312, are investigated; and impacts of the wall-fluid interactions, the pore width, and the temperature are taken into account. It is found that even if under supercritical conditions, the LJ fluid can undergo a "vapor-liquid phase transition" in confined space, i.e., the adsorption density undergoes a sudden increase with the bulk density. A greater wall-fluid attractive potential, a smaller pore width, and a lower temperature will bring about a stronger confinement effect. Besides, the adsorption pressure reaches a local minimum when the bulk density equals to a certain value, independent of the wall-fluid potential or pore width. The insights in this work have both practical and theoretical significances. Copyright © 2018 Elsevier Inc. All rights reserved.

Design and Simulation of Control Technique for Permanent Magnet Synchronous Motor Using Space Vector Pulse Width Modulation

NASA Astrophysics Data System (ADS)

Khan, Mansoor; Yong, Wang; Mustafa, Ehtasham

2017-07-01

After the rapid advancement in the field of power electronics devices and drives for last few decades, there are different kinds of Pulse Width Modulation techniques which have been brought to the market. The applications ranging from industrial appliances to military equipment including the home appliances. The vey common application for the PWM is three phase voltage source inverter, which is used to convert DC to AC in the homes to supply the power to the house in case electricity failure, usually named as Un-interrupted Power Supply. In this paper Space Vector Pulse Width Modulation techniques is discussed and analysed under the control technique named as Field Oriented Control. The working and implementation of this technique has been studied by implementing on the three phase bridge inverter. The technique is used to control the Permanente Magnet Synchronous Motor. The drive system is successfully implemented in MATLAB/Simulink using the mathematical equation and algorithm to achieve the satisfactory results. PI type of controller is used to tuned ers of the motothe parametr i.e. torque and current.

Ultrasonographic assessment of the atlanto-occipital space in healthy Thoroughbred foals and Thoroughbred foals with neonatal maladjustment syndrome.

PubMed

Mackenzie, C J; Haggett, E F; Pinchbeck, G L; Marr, C M

2017-05-01

Ultrasonography of the atlanto-occipital (AO) space may be useful as a non-invasive diagnostic tool in neonatal foals. The aims of the study were establish a range of values for ultrasonographic measurements of the AO space in healthy Thoroughbred foals and to compare these variables in healthy foals with foals diagnosed with neonatal maladjustment syndrome (NMS). Ultrasonography of the AO space was performed on 38 healthy Thoroughbred foals and 28 Thoroughbred foals with NMS≤4days of age. Transverse image spinal cord height (P=0.001), width (P<0.001) and spinal cord cross sectional area (P<0.001), and longitudinal image dorsoventral diameter of the ventral spinal artery, were significantly smaller in foals with NMS than in healthy foals. Ratios of spinal canal to cord width and cross sectional area were significantly smaller in healthy foals than in foals with NMS (P<0.001). Spinal canal variables were not significantly different between groups. Several ultrasonographic measurements of the AO space were significantly different between healthy foals and foals with NMS. Further investigation is warranted to investigate the clinical application of this technique. Copyright © 2017 Elsevier Ltd. All rights reserved.

36 CFR 1192.159 - Mobility aid accessibility.

Code of Federal Regulations, 2014 CFR

2014-07-01

... shall not exceed 5/8 inch (16 mm) in width. When the platform is at vehicle floor height with the inner... inches (1220 mm). Such space shall adjoin, and may overlap, an access path. Not more than 6 inches (150 mm) of the required clear floor space may be accommodated for footrests under another seat, modesty...

36 CFR 1192.159 - Mobility aid accessibility.

Code of Federal Regulations, 2012 CFR

2012-07-01

... shall not exceed 5/8 inch (16 mm) in width. When the platform is at vehicle floor height with the inner... inches (1220 mm). Such space shall adjoin, and may overlap, an access path. Not more than 6 inches (150 mm) of the required clear floor space may be accommodated for footrests under another seat, modesty...

49 CFR 38.23 - Mobility aid accessibility.

Code of Federal Regulations, 2012 CFR

2012-10-01

... in width. When the platform is at vehicle floor height with the inner barrier (if applicable) down or... accessible entrance as practicable and shall have a clear floor area of 30 inches by 48 inches. Such space shall adjoin, and may overlap, an access path. Not more than 6 inches of the required clear floor space...

49 CFR 38.23 - Mobility aid accessibility.

Code of Federal Regulations, 2014 CFR

2014-10-01

... in width. When the platform is at vehicle floor height with the inner barrier (if applicable) down or... accessible entrance as practicable and shall have a clear floor area of 30 inches by 48 inches. Such space shall adjoin, and may overlap, an access path. Not more than 6 inches of the required clear floor space...

24 CFR 3280.111 - Toilet compartments.

Code of Federal Regulations, 2014 CFR

2014-04-01

... inches. At least 21 inches of clear space shall be provided in front of each toilet. [40 FR 58752, Dec... compartments. Each toilet compartment must have a minimum width of 30 inches, with a minimum clear space of 21... 24 Housing and Urban Development 5 2014-04-01 2014-04-01 false Toilet compartments. 3280.111...

Free Space Optics Communication for Mobile Military Platforms

DTIC Science & Technology

2003-12-01

Federal Communications Commission FDA Food and Drug Administration FOV Field-of-View FSO Free Space Optics FWHM Full Width at Half Maximum Gbps...Physique et de Métrologie des Oscillateurs (LPMO) du CNRS UPR3203, associé à l’Université de Franche -Comté, 15 March 2002 [Schenk 2000] H. Schenk

Group space allowance has little effect on sow health, productivity, or welfare in a free-access stall system

USDA-ARS?s Scientific Manuscript database

Free-access stalls allow sows to choose the protection of a stall or use of a shared group space. This study investigated the effect of group space width: 0.91 (SS), 2.13 (IS), and 3.05 (LS) m on the health, production, behavior, and welfare of gestating sows. At gestational day (GD) 35.4 ± 2.3, 21 ...

Occupants' Perceptions of Amenity and Efficiency for Verification of Spatial Design Adequacy.

PubMed

Lee, Sangwon; Wohn, Kwangyun

2016-01-14

The best spatial design condition to satisfy the occupancy needs of amenity and efficiency is determined through analyzing the spatial design adequacy (SDA). In this study, the relationship between the space design elements and space on future occupants' perception are analyzed. The thirty-three participants reported their self-evaluated SDA that describes the quality of eight alternative housing living rooms with different spatial factors. The occupants were guided through the perception processing elaboration in order for them to evaluate the actual perception in the real space. The findings demonstrated that the spatial size (e.g., width, depth, and height) is significantly correlated with the overall satisfaction of amenity. It is also found that the spatial shape (e.g., the width-to-depth ratio, the height-to-area ratio, and room shape) may significantly influence the overall satisfaction of efficiency. The findings also demonstrate that the causal relationship between the spatial factors and space is clearly present in the occupants' perception, reflecting the time-sequential characteristics of the actual experience divided into amenity and efficiency. This result indicates that the correlation between the spatial factors and space of SDA under the occupants' perception processing elaboration can be a useful guide to predict the occupancy satisfaction of amenity and efficiency in real spaces.

Occupants’ Perceptions of Amenity and Efficiency for Verification of Spatial Design Adequacy

PubMed Central

Lee, Sangwon; Wohn, Kwangyun

2016-01-01

The best spatial design condition to satisfy the occupancy needs of amenity and efficiency is determined through analyzing the spatial design adequacy (SDA). In this study, the relationship between the space design elements and space on future occupants’ perception are analyzed. The thirty-three participants reported their self-evaluated SDA that describes the quality of eight alternative housing living rooms with different spatial factors. The occupants were guided through the perception processing elaboration in order for them to evaluate the actual perception in the real space. The findings demonstrated that the spatial size (e.g., width, depth, and height) is significantly correlated with the overall satisfaction of amenity. It is also found that the spatial shape (e.g., the width-to-depth ratio, the height-to-area ratio, and room shape) may significantly influence the overall satisfaction of efficiency. The findings also demonstrate that the causal relationship between the spatial factors and space is clearly present in the occupants’ perception, reflecting the time-sequential characteristics of the actual experience divided into amenity and efficiency. This result indicates that the correlation between the spatial factors and space of SDA under the occupants’ perception processing elaboration can be a useful guide to predict the occupancy satisfaction of amenity and efficiency in real spaces. PMID:26784211

Radiographic Measurement of Joint Space Width Using the Fixed Flexion View in 1,102 Knees of Japanese Patients with Osteoarthritis in Comparison with the Standing Extended View

PubMed Central

Kan, Hiroyuki; Arai, Yuji; Kobayashi, Masashi; Nakagawa, Shuji; Inoue, Hiroaki; Hino, Manabu; Komaki, Shintaro; Ikoma, Kazuya; Ueshima, Keiichiro; Fujiwara, Hiroyoshi; Kubo, Toshikazu

2017-01-01

Purpose The fixed flexion view (FFV) of the knee is considered useful for evaluating the joint space when assessing the severity of osteoarthritis (OA) of the knee. To clarify the usefulness of FFV for evaluation of the joint space and severity of knee OA, this study evaluated changes in the joint space on the FFV and standing extended view (SEV) in patients with knee OA. Materials and Methods The SEV and FFV images were acquired in 567 patients (1,102 knees) who visited the hospital with a chief complaint of knee joint pain. Medial joint space width (MJSW) and Kellgren-Lawrence (K-L) classification assessed using the SEV and FFV images were compared. Results Mean MJSW was significantly smaller when assessed on the FFV than on the SEV (3.02±1.55 mm vs. 4.31±1.30 mm; p<0.001). The K-L grade was the same or higher on the FFV than on the SEV. Conclusions The FFV is more useful than the SEV for evaluating the joint space in OA knees. Treatment strategies in patients with knee OA should be determined based on routinely acquired FFV images. PMID:28231651

Numerical Studies into Flow Profiles in Confined Lubricant

NASA Astrophysics Data System (ADS)

di Mare, Luca; Ponjavic, Aleks; Wong, Janet

2013-03-01

This paper documents a computational study of flow profiles in confined fluids. The study is motivated by experimental evidence for deviation from Couette flow found by one of the authors (JSW). The computational study examines several possible stress-strain relations. Since a linear profile is the only possible solution for a constant stress layer even in presence of a power law, the study introduces a functional dependence of the fluid viscosity on the distance from the wall. Based on this dependence, a family of scaling laws for the velocity profile near the wall is derived which matches the measured profiles. The existence of this scaling law requires the viscosity of the fluid to increase at least linearly away from the wall. This behaviour is explained at a microscopic level by considerations on the mobility of long molecules near a wall. This behaviour is reminiscent of the variation of eddy length scales in near-wall turbulence.

Influence of nitrogen as grain refiner in low carbon and microalloyed steels

NASA Astrophysics Data System (ADS)

Hasan, B. M.; Sathyamurthy, P.

2018-02-01

Microalloyed steel is replacing using of low alloy steel in automotive industry. Microalloying elements like vanadium, niobium and titanium are used to enhance the steel property. The current work is focused on using nitrogen as a strengthening element in existing steel grade. Nitrogen in free form acts as solid solution strengthener and in combined form as precipitates acts as grain refiner for enhancing strength. The problem of grain coarsening at high temperature in case carburizing steel was avoided by increasing nitrogen level from 60ppm to 200ppm. Grain size of ASTM no 10 is obtained at carburizing temperature of 950 °C by increasing nitrogen content from grain size no 6 with lower nitrogen. Mostly crankshaft is made from Cr-Mo alloyed steel. At JSW, nitrogen in the level of 130-200ppm is added to medium carbon steel to meet property requirement for crankshaft application

Modification and integration of JSW cyclotron GAS targets at the national institutes of health cyclotron facility

NASA Astrophysics Data System (ADS)

Finn, R.; Plascjak, P.; Sheh, Y.; Yamashita, Y.; Yoshida, H.; Adams, R.; Simpson, N.; Larson, S.

1987-04-01

The Cyclotron staff at the National Institutes of Health is involved in a comprehensive radionuclide preparation program which culminates with the formulation of numerous requested short-lived radiopharmaceutical agents for clinical evaluation. The existence of two cyclotrons and the requests for cyclotron-produced radionuclides, principally short-lived positron-emitting ones, necessitates an efficient and cost-effective program. The clinical need for 15O labelled water exemplifies the modification and effective coupling of two supplied gas target systems without detriment to either individual product. 15O labeled oxygen, produced from the 14N(d,n) 15O nuclear reaction, is combined with the target gas for 11C labelled cyanide production through standard fittings to achieve the chemical oxidation. The system allows an "on-line" product of extremely high yield and excellent radionuclidic purity. The operational characteristics of the redesigned commercial cyclotron targetry system and the radiochemical considerations are presented.

Ternary isocratic mobile phase optimization utilizing resolution Design Space based on retention time and peak width modeling.

PubMed

Kawabe, Takefumi; Tomitsuka, Toshiaki; Kajiro, Toshi; Kishi, Naoyuki; Toyo'oka, Toshimasa

2013-01-18

An optimization procedure of ternary isocratic mobile phase composition in the HPLC method using a statistical prediction model and visualization technique is described. In this report, two prediction models were first evaluated to obtain reliable prediction results. The retention time prediction model was constructed by modification from past respectable knowledge of retention modeling against ternary solvent strength changes. An excellent correlation between observed and predicted retention time was given in various kinds of pharmaceutical compounds by the multiple regression modeling of solvent strength parameters. The peak width of half height prediction model employed polynomial fitting of the retention time, because a linear relationship between the peak width of half height and the retention time was not obtained even after taking into account the contribution of the extra-column effect based on a moment method. Accurate prediction results were able to be obtained by such model, showing mostly over 0.99 value of correlation coefficient between observed and predicted peak width of half height. Then, a procedure to visualize a resolution Design Space was tried as the secondary challenge. An artificial neural network method was performed to link directly between ternary solvent strength parameters and predicted resolution, which were determined by accurate prediction results of retention time and a peak width of half height, and to visualize appropriate ternary mobile phase compositions as a range of resolution over 1.5 on the contour profile. By using mixtures of similar pharmaceutical compounds in case studies, we verified a possibility of prediction to find the optimal range of condition. Observed chromatographic results on the optimal condition mostly matched with the prediction and the average of difference between observed and predicted resolution were approximately 0.3. This means that enough accuracy for prediction could be achieved by the proposed procedure. Consequently, the procedure to search the optimal range of ternary solvent strength achieving an appropriate separation is provided by using the resolution Design Space based on accurate prediction. Copyright © 2012 Elsevier B.V. All rights reserved.

Factors associated with mandibular third molar eruption and impaction.

PubMed

Tsai, Hung-Huey

2005-01-01

A retrospective study, using panoramic radiographs, was conducted on 152 Taiwanese (72 males and 80 females) to investigate mandibular third molar eruption and impaction. The following measurements were made: inclinations and mesiodistal crown widths of the mandibular molars, vertical and horizontal spaces between the distal surface of the second molar and the anterior surface of the ramus, lengths and widths of the mandibular ramus and body, the ramus inclination, the mandibular plane angle, and the mandibular gonial angle. Differences between non-impaction and impaction groups were studied, and the variables were analyzed with multivariate discriminatory analysis. Significant differences between the two groups were found; variables describing spaces between the anterior of the ramus and the distal of the mandibular second molar and tooth size appeared to be the primary contributors to the differences observed.

Well-behaved dynamics in a dissipative nonideal periodically kicked rotator.

PubMed

Chacón, R; Martínez García-Hoz, A

2003-12-01

Well-behaved dynamical properties are found in a dissipative kicked rotator subjected to a periodic string of asymmetric pulses of finite amplitude and width. The stability boundaries of the equilibrium are determined to arbitrary approximation for trigonometric pulses by means of circular harmonic balance, and to first approximation for general elliptic pulses by means of an elliptic harmonic balance method. The bifurcation behavior at the stability boundaries is determined numerically. We show how the extension of the instability region of the equilibrium in pulse parameter space reaches a maximum as the pulse width is varied. We also characterize the dependence of the mean duration of the transients to the equilibrium on the pulse width. The evolution of the basins of attraction of chaotic attractors when solely the pulse width is varied is characterized numerically. Finally, we show that the order-chaos route when solely the width of the pulses is altered appears to be especially rich, including different types of crises. The mechanism underlying these reshaping-induced crises is discussed with the aid of a two-dimensional map.

Postretention stability after orthodontic closure of maxillary interincisor diastemas

PubMed Central

de MORAIS, Juliana Fernandes; de FREITAS, Marcos Roberto; de FREITAS, Karina Maria Salvatore; JANSON, Guilherme; CASTELLO BRANCO, Nuria

2014-01-01

Anterior spaces may interfere with smile attractiveness and compromise dentofacial harmony. They are among the most frequent reasons why patients seek orthodontic treatment. However, midline diastema is commonly cited as a malocclusion with high relapse incidence by orthodontists. Objectives This study aimed to evaluate the stability of maxillary interincisor diastemas closure and the association of their relapse and interincisor width, overjet, overbite and root parallelism. Material and Methods Sample comprised 30 patients with at least a pretreatment midline diastema of 0.5 mm or greater after eruption of the maxillary permanent canines. Dental casts and panoramic radiographs were taken at pretreatment, posttreatment and postretention. Results Before treatment, midline diastema width was 1.52 mm (SD=0.88) and right and left lateral diastema widths were 0.55 mm (SD=0.56) and 0.57 mm (SD=0.53), respectively. According to repeated measures analysis of variance, only midline diastema demonstrated significant relapse. In the overall sample the average relapse of midline diastema was 0.49 mm (SD=0.66), whilst the unstable patients showed a mean space reopening of 0.78 mm (SD=0.66). Diastema closure in the area between central and lateral incisors showed great stability. Multivariate correlation tests showed that only initial diastema width (β=0.60) and relapse of overjet (β=0.39) presented association with relapse of midline diastema. Conclusions Midline diastema relapse was statistically significant and occurred in 60% of the sample, while lateral diastemas closure remained stable after treatment. Only initial diastema width and overjet relapse showed association with relapse of midline diastema. There was no association between relapse of interincisor diastema and root parallelism. PMID:24918661

Correlation of mandibular impacted tooth and bone morphology determined by cone beam computed topography on a premise of third molar operation.

PubMed

Momin, M A; Matsumoto, K; Ejima, K; Asaumi, R; Kawai, T; Arai, Y; Honda, K; Yosue, T

2013-05-01

To determine the width and morphology of the mandible in the impacted third molar region, and to identify the location of the mandibular canal prior to planning impacted third molar operations. Cone beam computed tomography (CBCT) data of 87 mandibular third molars from 62 Japanese patients were analyzed in this study. The width of the lingual cortical bone and apex-canal distance were measured from cross-sectional images in which the cortical bone was thinnest at the lingual side in the third molar region. Images were used for measuring the space (distance between the inner border of the lingual cortical bone and outer surface of the third molar root), apex-canal distance (distance from the root of the third molar tooth to the superior border of the inferior alveolar canal) and the cortical bone (width between the inner and outer borders of the lingual cortical bone). The means of the space, apex-canal distance and lingual cortical width were 0.31, 1.99, and 0.68 mm, respectively. Impacted third molar teeth (types A-C) were observed at the following frequencies: type A (angular) 37 %; type B (horizontal), 42 %; type C (vertical), 21 %. The morphology of the mandible at the third molar region (types D-F) was observed as: type D (round), 49 %; type E (lingual extended), 18 %; and type F (lingual concave), 32 %. The width and morphology of the mandible with impacted teeth and the location of the mandibular canal at the third molar region could be clearly determined using cross-sectional CBCT images.

Porter-Thomas distribution in unstable many-body systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Volya, Alexander

We use the continuum shell model approach to explore the resonance width distribution in unstable many-body systems. The single-particle nature of a decay, the few-body character of the interaction Hamiltonian, and the collectivity that emerges in nonstationary systems due to the coupling to the continuum of reaction states are discussed. Correlations between the structures of the parent and daughter nuclear systems in the common Fock space are found to result in deviations of decay width statistics from the Porter-Thomas distribution.

Designing a fixed-blade gang ripsaw arbor with a pencil

Treesearch

Charles J. Gatchell; Charles J. Gatchell

1996-01-01

This paper presents a step-by-step procedure for designing the "best" sequence of saw spacings for a fixed-blade gang ripsaw arbor. Using the information contained in a cutting bill and knowledge of the lumber width distributions to be processed, thousands of possible saw spacing sequences can be reduced to a few good ones.

36 CFR § 1192.159 - Mobility aid accessibility.

Code of Federal Regulations, 2013 CFR

2013-07-01

... shall not exceed 5/8 inch (16 mm) in width. When the platform is at vehicle floor height with the inner... inches (1220 mm). Such space shall adjoin, and may overlap, an access path. Not more than 6 inches (150 mm) of the required clear floor space may be accommodated for footrests under another seat, modesty...

36 CFR 1192.107 - Restrooms.

Code of Federal Regulations, 2012 CFR

2012-07-01

... shelves may overlap the clear floor space at a lower height provided they can be easily folded up or moved... of the toilet seat. Seats shall not be sprung to return to a lifted position. (3) A grab bar at least... mobility aids and shall be connected to such a space by an unobstructed path having a minimum width of 32...

36 CFR § 1192.107 - Restrooms.

Code of Federal Regulations, 2013 CFR

2013-07-01

... shelves may overlap the clear floor space at a lower height provided they can be easily folded up or moved... of the toilet seat. Seats shall not be sprung to return to a lifted position. (3) A grab bar at least... mobility aids and shall be connected to such a space by an unobstructed path having a minimum width of 32...

36 CFR 1192.123 - Restrooms.

Code of Federal Regulations, 2014 CFR

2014-07-01

... the water closet. Fold-down or retractable seats or shelves may overlap the clear floor space at a... closet shall be 17 inches to 19 inches measured to the top of the toilet seat. Seats shall not be sprung....125(d) and shall be connected to such a space by an unobstructed path having a minimum width of 32...

36 CFR 1192.107 - Restrooms.

Code of Federal Regulations, 2014 CFR

2014-07-01

... shelves may overlap the clear floor space at a lower height provided they can be easily folded up or moved... of the toilet seat. Seats shall not be sprung to return to a lifted position. (3) A grab bar at least... mobility aids and shall be connected to such a space by an unobstructed path having a minimum width of 32...

36 CFR 1192.123 - Restrooms.

Code of Federal Regulations, 2012 CFR

2012-07-01

... the water closet. Fold-down or retractable seats or shelves may overlap the clear floor space at a... closet shall be 17 inches to 19 inches measured to the top of the toilet seat. Seats shall not be sprung....125(d) and shall be connected to such a space by an unobstructed path having a minimum width of 32...

Sub-Fourier characteristics of a δ-kicked-rotor resonance.

PubMed

Talukdar, I; Shrestha, R; Summy, G S

2010-07-30

We experimentally investigate the sub-Fourier behavior of a δ-kicked-rotor resonance by performing a measurement of the fidelity or overlap of a Bose-Einstein condensate exposed to a periodically pulsed standing wave. The temporal width of the fidelity resonance peak centered at the Talbot time and zero initial momentum exhibits an inverse cube pulse number (1/N3)-dependent scaling compared to a 1/N2 dependence for the mean energy width at the same resonance. A theoretical analysis shows that for an accelerating potential the width of the resonance in acceleration space depends on 1/N3, a property which we also verify experimentally. Such a sub-Fourier effect could be useful for high precision gravity measurements.

Effect of electrode design on crosstalk between neighboring organic field-effect transistors based on one single crystal

NASA Astrophysics Data System (ADS)

Li, Mengjie; Tang, Qingxin; Tong, Yanhong; Zhao, Xiaoli; Zhou, Shujun; Liu, Yichun

2018-03-01

The design of high-integration organic circuits must be such that the interference between neighboring devices is eliminated. Here, rubrene crystals were used to study the effect of the electrode design on crosstalk between neighboring organic field-effect transistors (OFETs). Results show that a decreased source/drain interval and gate electrode width can decrease the diffraction distance of the current, and therefore can weaken the crosstalk. In addition, the inherent low carrier concentration in organic semiconductors can create a high-resistance barrier at the space between gate electrodes of neighboring devices, limiting or even eliminating the crosstalk as a result of the gate electrode width being smaller than the source/drain electrode width.

Recursion equations in predicting band width under gradient elution.

PubMed

Liang, Heng; Liu, Ying

2004-06-18

The evolution of solute zone under gradient elution is a typical problem of non-linear continuity equation since the local diffusion coefficient and local migration velocity of the mass cells of solute zones are the functions of position and time due to space- and time-variable mobile phase composition. In this paper, based on the mesoscopic approaches (Lagrangian description, the continuity theory and the local equilibrium assumption), the evolution of solute zones in space- and time-dependent fields is described by the iterative addition of local probability density of the mass cells of solute zones. Furthermore, on macroscopic levels, the recursion equations have been proposed to simulate zone migration and spreading in reversed-phase high-performance liquid chromatography (RP-HPLC) through directly relating local retention factor and local diffusion coefficient to local mobile phase concentration. This new approach differs entirely from the traditional theories on plate concept with Eulerian description, since band width recursion equation is actually the accumulation of local diffusion coefficients of solute zones to discrete-time slices. Recursion equations and literature equations were used in dealing with same experimental data in RP-HPLC, and the comparison results show that the recursion equations can accurately predict band width under gradient elution.

Using Curved Crystals to Study Terrace-Width Distributions.

NASA Astrophysics Data System (ADS)

Einstein, Theodore L.

Recent experiments on curved crystals of noble and late transition metals (Ortega and Juurlink groups) have renewed interest in terrace width distributions (TWD) for vicinal surfaces. Thus, it is timely to discuss refinements of TWD analysis that are absent from the standard reviews. Rather than by Gaussians, TWDs are better described by the generalized Wigner surmise, with a power-law rise and a Gaussian decay, thereby including effects evident for weak step repulsion: skewness and peak shifts down from the mean spacing. Curved crystals allow analysis of several mean spacings with the same substrate, so that one can check the scaling with the mean width. This is important since such scaling confirms well-established theory. Failure to scale also can provide significant insights. Complicating factors can include step touching (local double-height steps), oscillatory step interactions mediated by metallic (but not topological) surface states, short-range corrections to the inverse-square step repulsion, and accounting for the offset between adjacent layers of almost all surfaces. We discuss how to deal with these issues. For in-plane misoriented steps there are formulas to describe the stiffness but not yet the strength of the elastic interstep repulsion. Supported in part by NSF-CHE 13-05892.

The effects of lane width, shoulder width, and road cross-sectional reallocation on drivers' behavioral adaptations.

PubMed

Mecheri, Sami; Rosey, Florence; Lobjois, Régis

2017-07-01

Previous research has shown that lane-width reduction makes drivers operate vehicles closer to the center of the road whereas hard-shoulder widening induces a position farther away from the road's center. The goal of the present driving-simulator study was twofold. First, it was aimed at further investigating the respective effects of lane and shoulder width on in-lane positioning strategies, by examining vehicle distance from the center of the lane. The second aim was to assess the impact on safety of three possible cross-sectional reallocations of the width of the road (i.e., three lane-width reductions with concomitant shoulder widening at a fixed cross-sectional width) as compared to a control road. The results confirmed that lane-width reduction made participants drive closer to the road's center. However, in-lane position was affected differently by lane narrowing, depending on the traffic situation. In the absence of oncoming traffic, lane narrowing gave rise to significant shifts in the car's distance from the lane's center toward the edge line, whereas this distance remained similar across lane widths during traffic periods. When the shoulders were at least 0.50m wide, participants drove farther away from both the road center and the lane center. Road reallocation operations resulted in vehicles positioned farther away from the edge of the road and less swerving behavior, without generating higher driving speeds. Finally, it is argued that road-space reallocation may serve as a good low-cost tool for providing a recovery area for steering errors, without impairing drivers' behavior. Copyright © 2017 Elsevier Ltd. All rights reserved.

Effect of traction on wrist joint space and cartilage visibility with and without MR arthrography

PubMed Central

Griffith, James F; Tang, W K; Ng, Alex W H; Yeung, David K W

2017-01-01

Objective: To compare the effect of traction during non-arthrographic and arthrographic MR examination of the wrist with regard to joint space width, joint fluid dispersion and cartilage surface visibility. Methods: Prospective 3-T MRI study of 100 wrists in 96 patients. The first 50 wrists underwent MR arthrography first without traction and then with traction. The following 50 wrists underwent standard MR first without traction and then with traction. On these examinations, two radiologists independently measured (i) joint space width, semi-quantitatively graded (ii) joint fluid dispersion between opposing cartilage surfaces and (iii) articular cartilage surface visibility. The three parameters were compared between the two groups. Results: Traction led to an increase in joint space width at nearly all joints in all patients (p < 0.05), although more so in the arthrography (∆ = 0.08–0.79 mm, all p < 0.05) than in the non-arthrography (∆ = 0.001–0.61 mm, all p < 0.05) group. Joint fluid dispersion and cartilage surface visibility improved after traction in nearly all joints (p < 0.05) in all patients and more so in the arthographic than in the non-arthrography group. Conclusion: Traction did significantly improve cartilage surface visibility for standard MRI of the wrist although the effect was not as great as that seen with MR arthography or MR arthrography with traction. Advances in knowledge: This is the first study to show the beneficial effect of traction during standard non-arthrography MRI of the wrist and compare the effect of traction between non-arthrographic and arthrographic MRI of the wrist. PMID:28181830

Insights into Regolith Dynamics from the Irradiation Record Preserved in Hayabusa Samples

NASA Technical Reports Server (NTRS)

Keller, Lindsay P.; Berger, E. L.

2014-01-01

The rates of space weathering processes are poorly constrained for asteroid surfaces, with recent estimates ranging over 5 orders of magnitude. The return of the first surface samples from a space-weathered asteroid by the Hayabusa mission and their laboratory analysis provides "ground truth" to anchor the timescales for space weathering. We determine the rates of space weathering on Itokawa by measuring solar flare track densities and the widths of solar wind damaged rims on grains. These measurements are made possible through novel focused ion beam (FIB) sample preparation methods.

Very High Quality Crystals of Wide-Gap II-VI Semiconductors: What for?

DTIC Science & Technology

2001-01-01

the reciprocal space mapping , by the etch pit density (EPD) measurements (to determine the density of dislocations) and by the measurement of the width...crystals. The EPD was in the range 5 x 1 + 104 cmn2 for Cdl.,ZnxTe crystals and about 104 cmz for ZnTe. The reciprocal space mapping of the crystals

Carbon Nanotube Tape Vibrating Gyroscope

NASA Technical Reports Server (NTRS)

Tucker, Dennis Stephen (Inventor)

2016-01-01

A vibrating gyroscope includes a piezoelectric strip having length and width dimensions. The piezoelectric strip includes a piezoelectric material and carbon nanotubes (CNTs) substantially aligned and polled along the strip's length dimension. A spindle having an axis of rotation is coupled to the piezoelectric strip. The axis of rotation is parallel to the strip's width dimension. A first capacitance sensor is mechanically coupled to the spindle for rotation therewith. The first capacitance sensor is positioned at one of the strip's opposing ends and is spaced apart from one of the strip's opposing faces. A second capacitance sensor is mechanically coupled to the spindle for rotation therewith. The second capacitance sensor is positioned at another of the strip's opposing ends and is spaced apart from another of the strip's opposing faces. A voltage source applies an AC voltage to the piezoelectric strip.

Innovative virtual reality measurements for embryonic growth and development.

PubMed

Verwoerd-Dikkeboom, C M; Koning, A H J; Hop, W C; van der Spek, P J; Exalto, N; Steegers, E A P

2010-06-01

Innovative imaging techniques, using up-to-date ultrasonic equipment, necessitate specific biometry. The aim of our study was to test the possibility of detailed human embryonic biometry using a virtual reality (VR) technique. In a longitudinal study, three-dimensional (3D) measurements were performed from 6 to 14 weeks gestational age in 32 pregnancies (n = 16 spontaneous conception, n = 16 IVF/ICSI). A total of 125 3D volumes were analysed in the I-Space VR system, which allows binocular depth perception, providing a realistic 3D illusion. Crown-rump length (CRL), biparietal diameter (BPD), occipito-frontal diameter (OFD), head circumference (HC) and abdominal circumference (AC) were measured as well as arm length, shoulder width, elbow width, hip width and knee width. CRL, BPD, OFD and HC could be measured in more than 96% of patients, and AC in 78%. Shoulder width, elbow width, hip width and knee width could be measured in more than 95% of cases, and arm length in 82% of cases. Growth curves were constructed for all variables. Ear and foot measurements were only possible beyond 9 weeks gestation. This study provides a detailed, longitudinal description of normal human embryonic growth, facilitated by a VR system. Growth curves were created for embryonic biometry of the CRL, BPD, HC and AC early in pregnancy and also of several 'new' biometric measurements. Applying virtual embryoscopy will enable us to diagnose growth and/or developmental delay earlier and more accurately. This is especially important for pregnancies at risk of severe complications, such as recurrent late miscarriage and early growth restriction.

A Radiographic Measurement of the Anterior Epidural Space at L4-5 Disc Level.

PubMed

Xu, Rui-Sheng; Wu, Jie-Shi; Lu, Hai-Dan; Zhu, Hao-Gang; Li, Xia; Dong, Jian; Yuan, Feng-Lai

2017-05-01

To observe the morphology character of the anterior epidural space at the L 4-5 disc level and to provide an anatomical basis for safely and accurately performing a percutaneous endoscopic lumbar discectomy (PELD). Fifty-five cases with L 5 S 1 lumbar disc herniation were included in this study, and cases with L 4-5 disease were excluded. When the puncture needle reached the epidural space at the L 5 S 1 level, iohexol was injected at the pressure of 50 cm H 2 O during the PELD, then C-Arm fluoroscopy was used to obtain standard lumbar frontal and lateral images. The widths of epidural space at the level of the L 4 lower endplate, the L 5 upper endplate, as well as the middle point of the L 4-5 disc were measured from the lumbar lateral X-ray film. Epidural space at the L 4-5 disc plane performs like a trapezium chart with a short side at the head end and a long side at the tail end in the lumbar lateral X-ray radiograph, while the average widths of epidural space were 10.2 ± 2.5, 12.3 ± 2.3, and 13.8 ± 2.6 mm at the upper, middle, and lower level of the L 4-5 disc. Understanding the morphological characteristics of epidural space will contribute to improving the safety of the tranforaminal percutaneous endoscopy technique. © 2017 Chinese Orthopaedic Association and John Wiley & Sons Australia, Ltd.

Generalized Reich-Moore R-matrix approximation

NASA Astrophysics Data System (ADS)

Arbanas, Goran; Sobes, Vladimir; Holcomb, Andrew; Ducru, Pablo; Pigni, Marco; Wiarda, Dorothea

2017-09-01

A conventional Reich-Moore approximation (RMA) of R-matrix is generalized into a manifestly unitary form by introducing a set of resonant capture channels treated explicitly in a generalized, reduced R-matrix. A dramatic reduction of channel space witnessed in conventional RMA, from Nc × Nc full R-matrix to Np × Np reduced R-matrix, where Nc = Np + Nγ, Np and Nγ denoting the number of particle and γ-ray channels, respectively, is due to Np < Nγ. A corresponding reduction of channel space in generalized RMA (GRMA) is from Nc × Nc full R-matrix to N × N, where N = Np + N, and where N is the number of capture channels defined in GRMA. We show that N = Nλ where Nλ is the number of R-matrix levels. This reduction in channel space, although not as dramatic as in the conventional RMA, could be significant for medium and heavy nuclides where N < Nγ. The resonant capture channels defined by GRMA accommodate level-level interference (via capture channels) neglected in conventional RMA. The expression for total capture cross section in GRMA is formally equal to that of the full Nc × NcR-matrix. This suggests that GRMA could yield improved nuclear data evaluations in the resolved resonance range at a cost of introducing N(N - 1)/2 resonant capture width parameters relative to conventional RMA. Manifest unitarity of GRMA justifies a method advocated by Fröhner and implemented in the SAMMY nuclear data evaluation code for enforcing unitarity of conventional RMA. Capture widths of GRMA are exactly convertible into alternative R-matrix parameters via Brune tranform. Application of idealized statistical methods to GRMA shows that variance among conventional RMA capture widths in extant RMA evaluations could be used to estimate variance among off-diagonal elements neglected by conventional RMA. Significant departure of capture widths from an idealized distribution may indicate the presence of underlying doorway states.

Fashion versus perception: the impact of surface lightness on the perceived dimensions of interior space.

PubMed

Oberfeld, Daniel; Hecht, Heiko

2011-06-01

We compare expert opinion with perceptual judgment regarding the influence of color on the perceived height and width of interior rooms. We hypothesize that contrary to popular belief, ceiling and wall lightness have additive effects on perceived height, whereas the lightness contrast between these surfaces is less important. We assessed the intuitions of architectural experts as to which surface colors maximize apparent height and compared these intuitions with psychophysical height and width estimates for rooms differing in ceiling, floor, and wall lightness. Experiment 1 was a survey of architectural experts and nonexperts. Experiments 2 and 3 presented virtual rooms varying in physical height, physical width, and surface lightness. In Experiment 1, both experts and nonexperts erroneously assumed that the lightness contrast between ceiling and walls influences perceived height Experiment 2 showed that the lightness contrast does not determine apparent height but that ceiling and wall lightness have additive effects. Experiment 3 demonstrated a decrease in perceived width with physical height, whereas the perceived height was not related to physical width. Apparent width was unaffected by ceiling lightness. Light ceiling and light walls make a room appear higher, whereas floor color has a weaker effect. We also found evidence for an asymmetric interaction between height and width. The question of how to color walls and ceiling to maximize the apparent size of a room can be answered empirically. Aesthetic considerations may interfere with the correct assessment of the effects of color in experts.

Direct Determination of the Space Weathering Rates in Lunar Soils and Itokawa Regolith from Sample Analyses

NASA Technical Reports Server (NTRS)

Keller, L. P.; Berger, E. L.; Christoffersen, R.; Zhang, S.

2016-01-01

Space weathering effects on airless bodies result largely from micrometeorite impacts and solar wind interactions. Decades of research have provided insights into space weathering processes and their effects, but a major unanswered question still remains: what is the rate at which these space weathering effects are acquired in lunar and asteroidal regolith materials? To determine the space weathering rate for the formation of rims on lunar anorthite grains, we combine the rim width and type with the exposure ages of the grains, as determined by the accumulation of solar flare particle tracks. From these analyses, we recently showed that space weathering effects in mature lunar soils (both vapor-deposited rims and solar wind amorphized rims) accumulate and attain steady state in 10(sup 6)-10(sup 7) y. Regolith grains from Itokawa also show evidence for space weathering effects, but in these samples, solar wind interactions appear to dominate over impactrelated effects such as vapor-deposition. While in our lunar work, we focused on anorthite, given its high abundance on the lunar surface, for the Itokawa grains, we focused on olivine. We previously studied 3 olivine grains from Itokawa and determined their solar flare track densities and described their solar wind damaged rims]. We also analyzed olivine grains from lunar soils, measured their track densities and rim widths, and used this data along with the Itokawa results to constrain the space weathering rate on Itokawa. We observe that olivine and anorthite have different responses to solar wind irradiation.

Creation of short microwave ablation zones: in vivo characterization of single and paired modified triaxial antennas.

PubMed

Lubner, Meghan G; Ziemlewicz, Tim J; Hinshaw, J Louis; Lee, Fred T; Sampson, Lisa A; Brace, Christopher L

2014-10-01

To characterize modified triaxial microwave antennas configured to produce short ablation zones. Fifty single-antenna and 27 paired-antenna hepatic ablations were performed in domestic swine (N = 11) with 17-gauge gas-cooled modified triaxial antennas powered at 65 W from a 2.45-GHz generator. Single-antenna ablations were performed at 2 (n = 16), 5 (n = 21), and 10 (n = 13) minutes. Paired-antenna ablations were performed at 1-cm and 2-cm spacing for 5 (n = 7 and n = 8, respectively) and 10 minutes (n = 7 and n = 5, respectively). Mean transverse width, length, and aspect ratio of sectioned ablation zones were measured and compared. For single antennas, mean ablation zone lengths were 2.9 cm ± 0.45, 3.5 cm ± 0.55, and 4.2 cm ± 0.40 at 2, 5, and 10 minutes, respectively. Mean widths were 1.8 cm ± 0.3, 2.0 cm ± 0.32, and 2.5 cm ± 0.25 at 2, 5, and 10 minutes, respectively. For paired antennas, mean length at 5 minutes with 1-cm and 2-cm spacing and 10 minutes with 1-cm and 2-cm spacing was 4.2 cm ± 0.9, 4.9 cm ± 1.0, 4.8 cm ± 0.5, and 4.8 cm ± 1.3, respectively. Mean width was 3.1 cm ± 1.0, 4.4 cm ± 0.7, 3.8 cm ± 0.4, and 4.5 cm ± 0.7, respectively. Paired-antenna ablations were more spherical (aspect ratios, 0.72-0.79 for 5-10 min) than single-antenna ablations (aspect ratios, 0.57-0.59). For paired-antenna ablations, 1-cm spacing appeared optimal, with improved circularity and decreased clefting compared with 2-cm spacing (circularity, 0.85 at 1 cm, 0.78 at 2 cm). Modified triaxial antennas can generate relatively short, spherical ablation zones. Paired-antenna ablations were rounder and larger in transverse dimension than single antenna ablations, with 1-cm spacing optimal for confluence of the ablation zone. Copyright © 2014 SIR. Published by Elsevier Inc. All rights reserved.

Analysis of Fault Spacing in Thrust-Belt Wedges Using Numerical Modeling

NASA Astrophysics Data System (ADS)

Regensburger, P. V.; Ito, G.

2017-12-01

Numerical modeling is invaluable in studying the mechanical processes governing the evolution of geologic features such as thrust-belt wedges. The mechanisms controlling thrust fault spacing in wedges is not well understood. Our numerical model treats the thrust belt as a visco-elastic-plastic continuum and uses a finite-difference, marker-in-cell method to solve for conservation of mass and momentum. From these conservation laws, stress is calculated and Byerlee's law is used to determine the shear stress required for a fault to form. Each model consists of a layer of crust, initially 3-km-thick, carried on top of a basal décollement, which moves at a constant speed towards a rigid backstop. A series of models were run with varied material properties, focusing on the angle of basal friction at the décollement, the angle of friction within the crust, and the cohesion of the crust. We investigate how these properties affected the spacing between thrusts that have the most time-integrated history of slip and therefore have the greatest effect on the large-scale undulations in surface topography. The surface position of these faults, which extend through most of the crustal layer, are identifiable as local maxima in positive curvature of surface topography. Tracking the temporal evolution of faults, we find that thrust blocks are widest when they first form at the front of the wedge and then they tend to contract over time as more crustal material is carried to the wedge. Within each model, thrust blocks form with similar initial widths, but individual thrust blocks develop differently and may approach an asymptotic width over time. The median of thrust block widths across the whole wedge tends to decrease with time. Median fault spacing shows a positive correlation with both wedge cohesion and internal friction. In contrast, median fault spacing exhibits a negative correlation at small angles of basal friction (<17˚) and a positive correlation with larger angles of basal friction. From these correlations, we will derive scaling laws that can be used to predict fault spacing in thrust-belt wedges.

Feasibility study of an image slicer for future space application

NASA Astrophysics Data System (ADS)

Calcines, A.; Ichimoto, K.

2014-08-01

This communication presents the feasibility study of an image slicer for future space missions, especially for the integral field unit (IFU) of the SUVIT (Solar UV-Visible-IR telescope) spectro-polarimeter on board the Japanese-led solar space mission Solar-C as a backup option. The MuSICa (Multi-Slit Image slicer based on collimator-Camera) image slicer concept, originally developed for the European Solar Telescope, has been adapted to the SUVIT requirements. The IFU will reorganizes a 2-D field of view of 10 x 10 arcsec2 into three slits of 0.18 arcsec width by 185.12 arcsec length using flat slicer mirrors of 100 μm width. The layout of MuSICa for Solar-C is telecentric and offers an optical quality limited by diffraction. The entrance for the SUVIT spectro-polarimeter is composed by the three IFU slits and one ordinal long slit to study, using high resolution spectro-polarimetry, the solar atmosphere (Photosphere and Chromosphere) within a spectral range between 520 nm (optionally 280 nm) and 1,100 nm.

Nonlinear dynamics of ice-wedge networks and resulting sensitivity to severe cooling events.

PubMed

Plug, L J; Werner, B T

2002-06-27

Patterns of subsurface wedges of ice that form along cooling-induced tension fractures, expressed at the ground surface by ridges or troughs spaced 10 30 m apart, are ubiquitous in polar lowlands. Fossilized ice wedges, which are widespread at lower latitudes, have been used to infer the duration and mean temperature of cold periods within Proterozoic and Quaternary climates, and recent climate trends have been inferred from fracture frequency in active ice wedges. Here we present simulations from a numerical model for the evolution of ice-wedge networks over a range of climate scenarios, based on the interactions between thermal tensile stress, fracture and ice wedges. We find that short-lived periods of severe cooling permanently alter the spacing between ice wedges as well as their fracture frequency. This affects the rate at which the widths of ice wedges increase as well as the network's response to subsequent climate change. We conclude that wedge spacing and width in ice-wedge networks mainly reflect infrequent episodes of rapidly falling ground temperatures rather than mean conditions.

Development of channel organization and roughness following sediment pulses in single‐thread, gravel bed rivers

USGS Publications Warehouse

Madej, Mary Ann

2001-01-01

Large, episodic inputs of coarse sediment (sediment pulses) in forested, mountain streams may result in changes in the size and arrangement of bed forms and in channel roughness. A conceptual model of channel organization delineates trajectories of response to sediment pulses for many types of gravel bed channels. Channels exhibited self‐organizing behavior to various degrees based on channel gradient, presence of large in‐channel wood or other forcing elements, the size of the sediment pulse, and the number of bed‐mobilizing flows since disturbance. Typical channel changes following a sediment pulse were initial decreases in water depth, in variability of bed elevations, and in the regularity of bed form spacing. Trajectories of change subsequently showed increased average water depth, more variable and complex bed topography, and increased uniformity of bed form spacing. Bed form spacing in streams with abundant forcing elements developed at a shorter spatial scale (two to five channel widths) than in streams without such forcing mechanisms (five to 10 channel widths). Channel roughness increased as bed forms developed.

Design of multiplier-less sharp transition width non-uniform filter banks using gravitational search algorithm

NASA Astrophysics Data System (ADS)

Bindiya T., S.; Elias, Elizabeth

2015-01-01

In this paper, multiplier-less near-perfect reconstruction tree-structured filter banks are proposed. Filters with sharp transition width are preferred in filter banks in order to reduce the aliasing between adjacent channels. When sharp transition width filters are designed as conventional finite impulse response filters, the order of the filters will become very high leading to increased complexity. The frequency response masking (FRM) method is known to result in linear-phase sharp transition width filters with low complexity. It is found that the proposed design method, which is based on FRM, gives better results compared to the earlier reported results, in terms of the number of multipliers when sharp transition width filter banks are needed. To further reduce the complexity and power consumption, the tree-structured filter bank is made totally multiplier-less by converting the continuous filter bank coefficients to finite precision coefficients in the signed power of two space. This may lead to performance degradation and calls for the use of a suitable optimisation technique. In this paper, gravitational search algorithm is proposed to be used in the design of the multiplier-less tree-structured uniform as well as non-uniform filter banks. This design method results in uniform and non-uniform filter banks which are simple, alias-free, linear phase and multiplier-less and have sharp transition width.

[Treatment of a single-tooth space in the occlusal system].

PubMed

Meijer, H J A; Cune, M S

2012-12-01

The space created by the absence of 1 not-free-ending tooth in an occlusal system can be indicated as a single-tooth space. For treating a single-tooth space, several options are available to restore the functions of the occlusal system. Feasible options are a resin-bonded fixed prosthesis, a conventional fixed prosthesis, and an implant-supported restoration. Implant-supported restorations have a good prognosis, high patient satisfaction, and the advantage that adjacent teeth are not involved in the treatment. Anxiety about surgical treatment, the width of the single-tooth space, and financial aspects may be reasons not to consider an implant-supported restoration as first-choice treatment.

49 CFR 172.446 - CLASS 9 label.

Code of Federal Regulations, 2012 CFR

2012-10-01

... top half. The black vertical stripes must be spaced, so that, visually, they appear equal in width to...” underlined and centered at the bottom. The solid horizontal line dividing the lower and upper half of the...

49 CFR 172.446 - CLASS 9 label.

Code of Federal Regulations, 2011 CFR

2011-10-01

... top half. The black vertical stripes must be spaced, so that, visually, they appear equal in width to...” underlined and centered at the bottom. The solid horizontal line dividing the lower and upper half of the...

49 CFR 172.446 - CLASS 9 label.

Code of Federal Regulations, 2013 CFR

2013-10-01

... top half. The black vertical stripes must be spaced, so that, visually, they appear equal in width to...” underlined and centered at the bottom. The solid horizontal line dividing the lower and upper half of the...

49 CFR 172.446 - CLASS 9 label.

Code of Federal Regulations, 2014 CFR

2014-10-01

... top half. The black vertical stripes must be spaced, so that, visually, they appear equal in width to...” underlined and centered at the bottom. The solid horizontal line dividing the lower and upper half of the...

Impact of overhang construction on girder design.

DOT National Transportation Integrated Search

2010-05-01

Economical constraints on the design of bridges usually necessitate the use of as few girders as possible across the : bridge width. The girders are typically uniformly spaced transversely with the deck extending past the fascia girders, thereby : re...

Large-scale transport across narrow gaps in rod bundles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guellouz, M.S.; Tavoularis, S.

1995-09-01

Flow visualization and how-wire anemometry were used to investigate the velocity field in a rectangular channel containing a single cylindrical rod, which could be traversed on the centreplane to form gaps of different widths with the plane wall. The presence of large-scale, quasi-periodic structures in the vicinity of the gap has been demonstrated through flow visualization, spectral analysis and space-time correlation measurements. These structures are seen to exist even for relatively large gaps, at least up to W/D=1.350 (W is the sum of the rod diameter, D, and the gap width). The above measurements appear to compatible with the fieldmore » of a street of three-dimensional, counter-rotating vortices, whose detailed structure, however, remains to be determined. The convection speed and the streamwise spacing of these vortices have been determined as functions of the gap size.« less

Adjustable high emittance gap filler. [reentry shielding for space shuttle vehicles

NASA Technical Reports Server (NTRS)

Leiser, D. B.; Stewart, D. A.; Smith, M.; Estrella, C. A.; Goldstein, H. E. (Inventor)

1981-01-01

A flexible, adjustable refractory filler is disclosed for filling gaps between ceramic tiles forming the heat shield of a space shuttle vehicle, to protect its aluminum skin during atmospheric reentry. The easily installed and replaced filler consists essentially of a strip of ceramic cloth coated, at least along both its longitudinal edges with a room temperature vulcanizable silicone rubber compound with a high emittance colored pigment. The filler may have one or more layers as the gap width requires. Preferred materials are basket weave aluminoborosilicate cloth, and a rubber compounded with silicon tetraboride as the emittance agent and finely divided borosilicate glass containing about 7.5% B2O3 as high temperature binder. The filler cloth strip or tape is cut to proper width and length, inserted into the gap, and fastened with previously applied drops of silicone rubber adhesive.

Current conduction in junction gate field effect transistors. Ph.D. Thesis

NASA Technical Reports Server (NTRS)

Kim, C.

1970-01-01

The internal physical mechanism that governs the current conduction in junction-gate field effect transistors is studied. A numerical method of analyzing the devices with different length-to-width ratios and doping profiles is developed. This method takes into account the two dimensional character of the electric field and the field dependent mobility. Application of the method to various device models shows that the channel width and the carrier concentration in the conductive channel decrease with increasing drain-to-source voltage for conventional devices. It also shows larger differential drain conductances for shorter devices when the drift velocity is not saturated. The interaction of the source and the drain gives the carrier accumulation in the channel which leads to the space-charge-limited current flow. The important parameters for the space-charge-limited current flow are found to be the L/L sub DE ratio and the crossover voltage.

Holographic insulator/superconductor transition with exponential nonlinear electrodynamics probed by entanglement entropy

NASA Astrophysics Data System (ADS)

Yao, Weiping; Yang, Chaohui; Jing, Jiliang

2018-05-01

From the viewpoint of holography, we study the behaviors of the entanglement entropy in insulator/superconductor transition with exponential nonlinear electrodynamics (ENE). We find that the entanglement entropy is a good probe to the properties of the holographic phase transition. Both in the half space and the belt space, the non-monotonic behavior of the entanglement entropy in superconducting phase versus the chemical potential is general in this model. Furthermore, the behavior of the entanglement entropy for the strip geometry shows that the confinement/deconfinement phase transition appears in both insulator and superconductor phases. And the critical width of the confinement/deconfinement phase transition depends on the chemical potential and the exponential coupling term. More interestingly, the behaviors of the entanglement entropy in their corresponding insulator phases are independent of the exponential coupling factor but depends on the width of the subsystem A.

Tunneling time in space fractional quantum mechanics

NASA Astrophysics Data System (ADS)

Hasan, Mohammad; Mandal, Bhabani Prasad

2018-02-01

We calculate the time taken by a wave packet to travel through a classically forbidden region of space in space fractional quantum mechanics. We obtain the close form expression of tunneling time from a rectangular barrier by stationary phase method. We show that tunneling time depends upon the width b of the barrier for b → ∞ and therefore Hartman effect doesn't exist in space fractional quantum mechanics. Interestingly we found that the tunneling time monotonically reduces with increasing b. The tunneling time is smaller in space fractional quantum mechanics as compared to the case of standard quantum mechanics. We recover the Hartman effect of standard quantum mechanics as a special case of space fractional quantum mechanics.

Around Marshall

NASA Image and Video Library

1993-06-30

This photograph shows STS-61 crewmemmbers training for the Hubble Space Telescope (HST) servicing mission in the Marshall Space Flight Center's (MSFC's) Neutral Buoyancy Simulator (NBS). Two months after its deployment in space, scientists detected a 2-micron spherical aberration in the primary mirror of the HST that affected the telescope's ability to focus faint light sources into a precise point. This imperfection was very slight, one-fiftieth of the width of a human hair. A scheduled Space Service servicing mission (STS-61) in 1993 permitted scientists to correct the problem. The MSFC NBS provided an excellent environment for testing hardware to examine how it would operate in space and for evaluating techniques for space construction and spacecraft servicing.

Keystone-designed buried de-epithelialized flap

PubMed Central

Kim, Hoon; Ryu, Wan Cheol; Yoon, Chi Sun; Kim, Kyu Nam

2017-01-01

Abstract Effective obliteration of dead space after reconstructive surgery facilitates a good cosmetic outcome and prevention of delayed wound healing and recurrent infection. We evaluated the efficacy of a keystone-designed buried de-epithelialized (KBD) flap for the obliteration of small to moderately sized surgical dead spaces. We reviewed the medical records of patients who received a KBD flap following removal of a mass or debridement of necrotic tissue from September 2015 to February 2016. The diagnosis, site, dead space dimensions, flap width, drain data, complications, and follow-up duration were recorded. Twenty-eight KBD flaps were evaluated, including 9 cases of fat necrosis, 7 cases of epidermal cyst, and 12 cases of lipoma. Dead space dimensions ranged from 2 × 1.5 × 1 cm to 10 × 5 × 3 cm, with a mean depth of 2.01 cm. Flap sizes ranged from 2.5 × 1 cm to 11 × 3 cm, with a mean flap width of 2.01 cm. No postoperative complications, such as seroma or hematoma, occurred. The cosmetic results were favorable, and all patients were satisfied with their final outcomes. The KBD flap is useful for the obliteration of small to moderately sized surgical dead spaces both spatially and physiologically and shows excellent cosmetic outcomes. PMID:28538418

History of Hubble Space Telescope (HST)

NASA Image and Video Library

1993-07-09

This photograph shows an STS-61 astronaut training for the Hubble Space Telescope (HST) servicing mission (STS-61) in the Marshall Space Flight Center's (MSFC's) Neutral Buoyancy Simulator (NBS). Two months after its deployment in space, scientists detected a 2-micron spherical aberration in the primary mirror of the HST that affected the telescope's ability to focus faint light sources into a precise point. This imperfection was very slight, one-fiftieth of the width of a human hair. A scheduled Space Service servicing mission (STS-61) in 1993 permitted scientists to correct the problem. The MSFC NBS provided an excellent environment for testing hardware to examine how it would operate in space and for evaluating techniques for space construction and spacecraft servicing.

Correlation and agreement of a digital and conventional method to measure arch parameters.

PubMed

Nawi, Nes; Mohamed, Alizae Marny; Marizan Nor, Murshida; Ashar, Nor Atika

2018-01-01

The aim of the present study was to determine the overall reliability and validity of arch parameters measured digitally compared to conventional measurement. A sample of 111 plaster study models of Down syndrome (DS) patients were digitized using a blue light three-dimensional (3D) scanner. Digital and manual measurements of defined parameters were performed using Geomagic analysis software (Geomagic Studio 2014 software, 3D Systems, Rock Hill, SC, USA) on digital models and with a digital calliper (Tuten, Germany) on plaster study models. Both measurements were repeated twice to validate the intraexaminer reliability based on intraclass correlation coefficients (ICCs) using the independent t test and Pearson's correlation, respectively. The Bland-Altman method of analysis was used to evaluate the agreement of the measurement between the digital and plaster models. No statistically significant differences (p > 0.05) were found between the manual and digital methods when measuring the arch width, arch length, and space analysis. In addition, all parameters showed a significant correlation coefficient (r ≥ 0.972; p < 0.01) between all digital and manual measurements. Furthermore, a positive agreement between digital and manual measurements of the arch width (90-96%), arch length and space analysis (95-99%) were also distinguished using the Bland-Altman method. These results demonstrate that 3D blue light scanning and measurement software are able to precisely produce 3D digital model and measure arch width, arch length, and space analysis. The 3D digital model is valid to be used in various clinical applications.

Implications of dune pattern analysis for Titan's surface history

NASA Astrophysics Data System (ADS)

Savage, Christopher J.; Radebaugh, Jani; Christiansen, Eric H.; Lorenz, Ralph D.

2014-02-01

Analysis of large-scale morphological parameters can reveal the reaction of dunes to changes in atmospheric and sedimentary conditions. Over 7000 dune width and 7000 dune spacing measurements were obtained for linear dunes in regions across Saturn's moon Titan from images T21, T23, T28, T44 and T48 collected by the Synthetic Aperture RADAR (SAR) aboard the Cassini spacecraft in order to reconstruct the aeolian surface history of Titan. Dunes in the five study areas are all linear in form, with a mean width of 1.3 km and mean crest spacing of 2.7 km, similar to dunes in the African Saharan and Namib deserts on Earth. At the resolution of Cassini SAR, the dunes have the morphology of large linear dunes, and they lack evidence for features of compound or complex dunes. The large size, spacing and uniform morphology are all indicators that Titan's dunes are mature features, in that they have grown toward a steady state for a long period of time. Dune width decreases to the north, perhaps from increased sediment stabilization caused by a net transport of moisture from south to north, or from increased maturity in dunes to the south. Cumulative probability plots of dune parameters measured at different locations across Titan indicate there is a single population of intermediate-to-large-sized dunes on Titan. This suggests that, unlike analogous dunes in the Namib and Agneitir Sand Seas, dune-forming conditions that generated the current set of dunes were stable and active long enough to erase any evidence of past conditions.

Factors Related to Increased Ulnar Collateral Ligament Thickness on Stress Sonography of the Elbow in Asymptomatic Youth and Adolescent Baseball Pitchers.

PubMed

Atanda, Alfred; Averill, Lauren W; Wallace, Maegen; Niiler, Tim A; Nazarian, Levon N; Ciccotti, Michael G

2016-12-01

Stress ultrasound (SUS) of the elbow has demonstrated changes in the anterior band of the ulnar collateral ligament (UCL) in professional and high school-aged pitchers. However, there have been no large reports correlating pitching history data with SUS changes in youth and adolescent baseball pitchers. Changes of the UCL on SUS will correlate with pitching volume in youth and adolescent baseball pitchers. Cross-sectional study; Level of evidence, 3. SUS of the elbow was performed in both elbows of 102 youth and adolescent baseball pitchers. UCL thickness and the width of the ulnohumeral joint, at rest and with 150 N of valgus stress, were measured using a standardized, instrumented device. Demographic data, arm measurements, and a pitching history questionnaire were recorded as well. The pitchers were separated into 2 groups based on age: group 1 (12-14 years) and group 2 (15-18 years). SUS findings of the dominant elbows were compared between the 2 groups. Correlation analysis and linear regression were used to identify relationships between SUS findings and pitching history data. In all pitchers, the mean UCL thickness was 4.40 mm in the dominant elbow and 4.11 mm in the nondominant elbow (P =.03). There was no significant difference between elbows in any joint space characteristics. A comparison of group 1 versus group 2 demonstrated significant differences in UCL thickness (4.13 vs 4.96 mm; P < .001), resting joint space width (6.56 vs 4.04 mm; P < .001), and stressed joint space width (7.68 vs 4.07 mm; P < .001). There was no difference in the change in joint space width between the 2 groups (1.11 vs 0.76 mm; P = .05). The UCL was significantly thicker in pitchers who threw more than 67 pitches per appearance (4.69 vs 4.14 mm), who pitched more than 5 innings per appearance (4.76 vs 4.11 mm), and who had more than 5.5 years of pitching experience (4.71 vs 4.07 mm; P < .001). Linear regression demonstrated that age, weight, and pitches per appearance (R 2 = 0.114, 0.370, and 0.326, respectively) significantly correlated with UCL thickness. These findings suggest that UCL thickness increases as pitchers get older and heavier and as they increase their pitch volumes. © 2016 The Author(s).

Analytical theory of the space-charge region of lateral p-n junctions in nanofilms

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gurugubelli, Vijaya Kumar, E-mail: vkgurugubelli@gmail.com; Karmalkar, Shreepad

There is growing interest in fabricating conventional semiconductor devices in a nanofilm which could be a 3D material with one reduced dimension (e.g., silicon-on-insulator (SOI) film), or single/multiple layers of a 2D material (e.g., MoS{sub 2}), or a two dimensional electron gas/two dimensional hole gas (2DEG/2DHG) layer. Lateral p-n junctions are essential parts of these devices. The space-charge region electrostatics in these nanofilm junctions is strongly affected by the surrounding field, unlike in bulk junctions. Current device physics of nanofilms lacks a simple analytical theory of this 2D electrostatics of lateral p-n junctions. We present such a theory taking intomore » account the film's thickness, permittivity, doping, interface charge, and possibly different ambient permittivities on film's either side. In analogy to the textbook theory of the 1D electrostatics of bulk p-n junctions, our theory yields simple formulas for the depletion width, the extent of space-charge tails beyond this width, and the screening length associated with the space-charge layer in nanofilm junctions; these formulas agree with numerical simulations and measurements. Our theory introduces an electrostatic thickness index to classify nanofilms into sheets, bulk and intermediate sized.« less

Macro Fiber Piezocomposite Actuator Poling Study

NASA Technical Reports Server (NTRS)

Werlink, Rudy J.; Bryant, Robert G.; Manos, Dennis

2002-01-01

The performance and advantages of Piezocomposite Actuators are to provide a low cost, in-situ actuator/sensor that is flexible, low profile and high strain per volt performance in the same plane of poled voltage. This paper extends reported data for the performance of these Macrofiber Composite (MFC) Actuators to include 4 progressively narrower Intedigitized electrode configurations with several line widths and spacing ratios. Data is reported for max free strain, average strain per applied volt, poling (alignment of the electric dipoles of the PZT ceramic) voltage vs. strain and capacitance, time to poling voltage 95% saturation. The output strain per volt progressively increases as electrode spacing decreases, with saturation occurring at lower poling voltages. The narrowest spacing ratio becomes prone to voltage breakdown or short circuits limiting the spacing width with current fabrication methods. The capacitance generally increases with increasing poling voltage level but has high sensitivity to factors such as temperature, moisture and time from poling which limit its usefulness as a simple indicator. The total time of applied poling voltage to saturate or fully line up the dipoles in the piezoceramic was generally on the order of 5-20 seconds. Less sensitivity to poling due to the applied rate of voltage increase over a 25 to 500 volt/second rate range was observed.

Static Thermochemical Model of COREX Melter Gasifier

NASA Astrophysics Data System (ADS)

Srishilan, C.; Shukla, Ajay Kumar

2018-02-01

COREX is one of the commercial smelting reduction processes. It uses the finer size ore and semi-soft coal instead of metallurgical coke to produce hot metal from iron ore. The use of top gas with high calorific value as a by-product export gas makes the process economical and green. The predictive thermochemical model of the COREX process presented here enables rapid computation of process parameters such as (1) required amount of ore, coal, and flux; (2) amount of slag and gas generated; and (3) gas compositions (based on the raw material and desired hot metal quality). The model helps in predicting the variations in process parameters with respect to the (1) degree of metallization and (2) post-combustion ratio for given raw material conditions. In general reduction in coal, flux, and oxygen, the requirement is concomitant with an increase in the degree of metallization and post-combustion ratio. The model reported here has been benchmarked using industrial data obtained from the JSW Steel Plant, India.

Statistical self-similarity of width function maxima with implications to floods

USGS Publications Warehouse

Veitzer, S.A.; Gupta, V.K.

2001-01-01

Recently a new theory of random self-similar river networks, called the RSN model, was introduced to explain empirical observations regarding the scaling properties of distributions of various topologic and geometric variables in natural basins. The RSN model predicts that such variables exhibit statistical simple scaling, when indexed by Horton-Strahler order. The average side tributary structure of RSN networks also exhibits Tokunaga-type self-similarity which is widely observed in nature. We examine the scaling structure of distributions of the maximum of the width function for RSNs for nested, complete Strahler basins by performing ensemble simulations. The maximum of the width function exhibits distributional simple scaling, when indexed by Horton-Strahler order, for both RSNs and natural river networks extracted from digital elevation models (DEMs). We also test a powerlaw relationship between Horton ratios for the maximum of the width function and drainage areas. These results represent first steps in formulating a comprehensive physical statistical theory of floods at multiple space-time scales for RSNs as discrete hierarchical branching structures. ?? 2001 Published by Elsevier Science Ltd.

The potential of space exploration for education

NASA Technical Reports Server (NTRS)

Shair, Fredrick H.

1993-01-01

Space exploration and observations from space offer unique opportunities with respect to education. Recent technical advances have significantly increased the width and sensitivity of the electromagnetic spectrum window through which we are able to 'see' the universe. Observations from space have forced a realization that the earth is a beautiful, complex, and interconnected system. Space astronomy and the remote sensing of objects throughout our solar system have the potential of providing unique educational opportunities. Modern technologies have significantly reduced the cost of collecting, transmitting and processing data. Consequently, we are entering an age where it is possible to open up the process of discovery to almost everyone - and especially to young people throughout the world.

Astronaut Training in the Neutral Buoyancy Simulator

NASA Technical Reports Server (NTRS)

1993-01-01

This photograph shows an STS-61 astronaut training for the Hubble Space Telescope (HST) servicing mission (STS-61) in the Marshall Space Flight Center's (MSFC's) Neutral Buoyancy Simulator (NBS). Two months after its deployment in space, scientists detected a 2-micron spherical aberration in the primary mirror of the HST that affected the telescope's ability to focus faint light sources into a precise point. This imperfection was very slight, one-fiftieth of the width of a human hair. A scheduled Space Service servicing mission (STS-61) in 1993 permitted scientists to correct the problem. The MSFC NBS provided an excellent environment for testing hardware to examine how it would operate in space and for evaluating techniques for space construction and spacecraft servicing.

COnstrained Data Extrapolation (CODE): A new approach for high definition vascular imaging from low resolution data.

PubMed

Song, Yang; Hamtaei, Ehsan; Sethi, Sean K; Yang, Guang; Xie, Haibin; Mark Haacke, E

2017-12-01

To introduce a new approach to reconstruct high definition vascular images using COnstrained Data Extrapolation (CODE) and evaluate its capability in estimating vessel area and stenosis. CODE is based on the constraint that the full width half maximum of a vessel can be accurately estimated and, since it represents the best estimate for the width of the object, higher k-space data can be generated from this information. To demonstrate the potential of extracting high definition vessel edges using low resolution data, both simulated and human data were analyzed to better visualize the vessels and to quantify both area and stenosis measurements. The results from CODE using one-fourth of the fully sampled k-space data were compared with a compressed sensing (CS) reconstruction approach using the same total amount of data but spread out between the center of k-space and the outer portions of the original k-space to accelerate data acquisition by a factor of four. For a sufficiently high signal-to-noise ratio (SNR) such as 16 (8), we found that objects as small as 3 voxels in the 25% under-sampled data (6 voxels when zero-filled) could be used for CODE and CS and provide an estimate of area with an error <5% (10%). For estimating up to a 70% stenosis with an SNR of 4, CODE was found to be more robust to noise than CS having a smaller variance albeit a larger bias. Reconstruction times were >200 (30) times faster for CODE compared to CS in the simulated (human) data. CODE was capable of producing sharp sub-voxel edges and accurately estimating stenosis to within 5% for clinically relevant studies of vessels with a width of at least 3pixels in the low resolution images. Copyright © 2017 Elsevier Inc. All rights reserved.

Stabilization of a finite slice in miscible displacement in homogeneous porous media

NASA Astrophysics Data System (ADS)

Pramanik, Satyajit; Mishra, Manoranjan

2016-11-01

We numerically studied the miscible displacement of a finite slice of variable viscosity and density. The stability of the finite slice depends on different flow parameters, such as displacement velocity U, mobility ratio R , and the density contrast. Series of numerical simulations corresponding to different ordered pair (R, U) in the parameter space, and a given density contrast reveal six different instability regions. We have shown that independent of the width of the slice, there always exists a region of stable displacement, and below a critical value of the slice width, this stable region increases with decreasing slice width. Further we observe that the viscous fingering (buoyancy-induced instability) at the upper interface induces buoyancy-induced instability (viscous fingering) at the lower interface. Besides the fundamental fluid dynamics understanding, our results can be helpful to model CO2 sequestration and chromatographic separation.

Statistical characterization of thermal plumes in turbulent thermal convection

NASA Astrophysics Data System (ADS)

Zhou, Sheng-Qi; Xie, Yi-Chao; Sun, Chao; Xia, Ke-Qing

2016-09-01

We report an experimental study on the statistical properties of the thermal plumes in turbulent thermal convection. A method has been proposed to extract the basic characteristics of thermal plumes from temporal temperature measurement inside the convection cell. It has been found that both plume amplitude A and cap width w , in a time domain, are approximately in the log-normal distribution. In particular, the normalized most probable front width is found to be a characteristic scale of thermal plumes, which is much larger than the thermal boundary layer thickness. Over a wide range of the Rayleigh number, the statistical characterizations of the thermal fluctuations of plumes, and the turbulent background, the plume front width and plume spacing have been discussed and compared with the theoretical predictions and morphological observations. For the most part good agreements have been found with the direct observations.

Axially Tapered And Bilayer Microchannels For Evaporative Cooling Devices

DOEpatents

Nilson, Robert; Griffiths, Stewart

2005-10-04

The invention consists of an evaporative cooling device comprising one or more microchannels whose cross section is axially reduced to control the maximum capillary pressure differential between liquid and vapor phases. In one embodiment, the evaporation channels have a rectangular cross section that is reduced in width along a flow path. In another embodiment, channels of fixed width are patterned with an array of microfabricated post-like features such that the feature size and spacing are gradually reduced along the flow path. Other embodiments incorporate bilayer channels consisting of an upper cover plate having a pattern of slots or holes of axially decreasing size and a lower fluid flow layer having channel widths substantially greater than the characteristic microscale dimensions of the patterned cover plate. The small dimensions of the cover plate holes afford large capillary pressure differentials while the larger dimensions of the lower region reduce viscous flow resistance.

Space-Wave Routing via Surface Waves Using a Metasurface System.

PubMed

Achouri, Karim; Caloz, Christophe

2018-05-15

We introduce the concept of a metasurface system able to route space waves via surface waves. This concept may be used to laterally shift or modulate the beam width of scattered waves. The system is synthesized based on a momentum transfer approach using phase-gradient metasurfaces. The concept is experimentally verified in an "electromagnetic periscope". Additionally, we propose two other potential applications namely a beam expander and a multi-wave refractor.

Microgravity

NASA Image and Video Library

2000-01-30

Engineers from NASA's Glenn Research Center, demonstrate access to one of the experiment racks planned for the U.S. Destiny laboratory module on the International Space Station. This mockup has the full diameter, full corridor width, and half the length of the module. The mockup includes engineering mockups of the Fluids and Combustion Facility being developed by NASA's Glenn Research Center. (The full module will be six racks long; the mockup is three rack long) Photo credit: NASA/Marshall Space Flight Center

NUCLEAR REACTORS

DOEpatents

Long, E.; Ashby, J.W.

1958-09-16

ABS>A graphite moderator structure is presented for a nuclear reactor compriscd of an assembly of similarly orientated prismatic graphite blocks arranged on spaced longitudinal axes lying in common planes wherein the planes of the walls of the blocks are positioned so as to be twisted reintive to the planes of said axes so thatthe unlmpeded dtrect paths in direction wholly across the walls of the blocks are limited to the width of the blocks plus spacing between the blocks.

High-Resolution Graphene Films for Electrochemical Sensing via Inkjet Maskless Lithography.

PubMed

Hondred, John A; Stromberg, Loreen R; Mosher, Curtis L; Claussen, Jonathan C

2017-10-24

Solution-phase printing of nanomaterial-based graphene inks are rapidly gaining interest for fabrication of flexible electronics. However, scalable manufacturing techniques for high-resolution printed graphene circuits are still lacking. Here, we report a patterning technique [i.e., inkjet maskless lithography (IML)] to form high-resolution, flexible, graphene films (line widths down to 20 μm) that significantly exceed the current inkjet printing resolution of graphene (line widths ∼60 μm). IML uses an inkjet printed polymer lacquer as a sacrificial pattern, viscous spin-coated graphene, and a subsequent graphene lift-off to pattern films without the need for prefabricated stencils, templates, or cleanroom technology (e.g., photolithography). Laser annealing is employed to increase conductivity on thermally sensitive, flexible substrates [polyethylene terephthalate (PET)]. Laser annealing and subsequent platinum nanoparticle deposition substantially increases the electroactive nature of graphene as illustrated by electrochemical hydrogen peroxide (H 2 O 2 ) sensing [rapid response (5 s), broad linear sensing range (0.1-550 μm), high sensitivity (0.21 μM/μA), and low detection limit (0.21 μM)]. Moreover, high-resolution, complex graphene circuits [i.e., interdigitated electrodes (IDE) with varying finger width and spacing] were created with IML and characterized via potassium chloride (KCl) electrochemical impedance spectroscopy (EIS). Results indicated that sensitivity directly correlates to electrode feature size as the IDE with the smallest finger width and spacing (50 and 50 μm) displayed the largest response to changes in KCl concentration (∼21 kΩ). These results indicate that the developed IML patterning technique is well-suited for rapid, solution-phase graphene film prototyping on flexible substrates for numerous applications including electrochemical sensing.

Creation of short microwave ablation zones: In Vivo Characterization of single and paired Modified Triaxial Antennas Laboratory Investigation

PubMed Central

Lubner, Meghan G.; Ziemlewicz, Tim J; Hinshaw, J. Louis; Lee, Fred T.; Sampson, Lisa J.; Brace, Chris L.

2014-01-01

Purpose To characterize modified triaxial microwave antennas configured to produce short ablation zones. Materials and Methods 50 single- and 27 paired-antenna hepatic ablations were performed in domestic swine (n=11) with 17-gauge, gas-cooled modified triaxial antennas powered at 65W from a 2.45 GHz generator. Single-antenna ablations were performed at 2 (n=16), 5 (n=21), and 10 (n=13) minutes. Paired-antenna ablations were performed at 1-cm and 2-cm spacing for 5 (n=7, n=8) and 10 minutes (n=7, n=5). Mean transverse width, length and aspect ratio of sectioned ablation zones were measured and compared. Results For single antennas, mean ablation zone length was 2.9±0.45, 3.5±0.55 and 4.2±0.40 cm at 2, 5, and 10 minutes respectively. Mean width was 1.8±0.3, 2.0±0.32, 2.5±0.25 cm at 2, 5, and 10 minutes. For paired antennas, mean length at 5 min 1 and 2 cm and 10 min 1 and 2 cm spacing was 4.2±0.9, 4.4±0.9, 4.8±0.5 and 4.3±0.9 cm respectively. Mean width was 3.1±1.0, 4.0±0.8 and 3.8±0.4, 4.2±0.6 cm respectively. Paired-antenna ablations were more spherical (aspect ratios 0.72-0.79 for 5-10 min) than single-antenna ablations (0.57-0.59). For paired-antenna ablations, 1 cm spacing appeared optimal, with improved circularity and decreased clefting compared to 2 cm spacing (circ 1 cm 0.85, 2 cm 0.78). Conclusion Modified triaxial antennas can generate relatively short, spherical ablation zones. Paired-antenna ablations were rounder and larger in transverse dimension compared to single antenna ablations, with 1 cm spacing optimal for confluence of the ablation zone. PMID:25156644

Nanocrystals with linear and branched topology

DOEpatents

Alivisatos, A. Paul; Milliron, Delia; Manna, Liberato; Hughes, Steven M.

2007-12-04

Disclosed herein are nanostructures comprising distinct dots and rods coupled through potential barriers of tuneable height and width, and arranged in three dimensional space at well defined angles and distances. Such control allows investigation of potential applications ranging from quantum information processing to artificial photosynthesis.

--No Title--

Science.gov Websites

; width: 650px ; background-color: white } div.notesPanel { ; padding-right: 25px } li { ; margin-left ; border-color: black } table { ; border-spacing: 0px ; border-collapse: collapse } th, td { ; text-align ; border-style: none } a { ; text-decoration: none ; color: inherit } img { ; border: none

Solar Ion Processing of Itokawa Grains: Constraints on Surface Exposure Times

NASA Technical Reports Server (NTRS)

Christoffersen, R.; Keller, L. P.

2015-01-01

Analytical TEM observations obtained to date reveal that a significant sub-population of grains returned from the surface of asteroid Itokawa have had their outer 30-100 nm processed by space weathering effects. Although the effects include some surface deposition of condensed impact vapor and isolated impact melt splashes, much of the width of the space weathered outer margins or "rims" on grains is derived from solar wind processing of the original host grain. Similar to what has long been reported for some lunar grains, the ion-processed rims on Itokawa grains exhibit varing degrees and depths of penetration of atomic-displacement ion damage, resulting in complete amorphization for some rims (particularly in plagioclase), or formation of highly defective but still crystalline structures in others (particularly in pyroxene and olivine). Possibly different from lunar grains, however, is the presence of isolated internal cavities or voids in Itokawa grain rims, which may be implantation "bubbles" due to accumulating implanted solar wind H and/or He. For a given mineral exposed at a particular set of long term solar wind conditions, the level of ion damage in a given grain rim, the depth of damage penetration represented by the rim width, and the formation or lack of formation of implantation bubbles can all be linked to the time spent by the grain in an uncovered state on the topmost, space-exposed, regolith surface. For the lunar case, we have previously shown that with reasonable assumptions about solar wind characteristics over time, a model can be developed to estimate this exposure time based on the width of amorphous rims on lunar grains. Here we report on an expansion of the model to cover exposure time information contained in the array of solar ion-induced features in Itokawa grains.

Influence of sex and ethnic tooth-size differences on mixed-dentition space analysis

PubMed Central

Altherr, Edward R.; Koroluk, Lorne D.; Phillips, Ceib

2013-01-01

Introduction Most mixed-dentition space analyses were developed by using subjects of northwestern European descent and unspecified sex. The purpose of this study was to determine the predictive accuracy of the Tanaka-Johnston analysis in white and black subjects in North Carolina. Methods A total of 120 subjects (30 males and 30 females in each ethnic group) were recruited from clinics at the University of North Carolina School of Dentistry. Ethnicity was verified to 2 previous generations. All subjects were less than 21 years of age and had a full complement of permanent teeth. Digital calipers were used to measure the mesiodistal widths of all teeth on study models fabricated from alginate impressions. The predicted widths of the canines and the premolars in both arches were compared with the actual measured widths. Results In the maxillary arch, there was a significant interaction of ethnicity and sex on the predictive accuracy of the Tanaka-Johnston analysis (P = .03, factorial ANOVA). The predictive accuracy was significantly overestimated in the white female group (P <.001, least square means). In the mandibular arch, there was no significant interaction between ethnicity and sex (P = .49). Conclusions The Tanaka-Johnston analysis significantly overestimated in females (P <.0001) and underestimated in blacks (P <.0001) (factorial ANOVA). Regression equations were developed to increase the predictive accuracy in both arches. (Am J Orthod Dentofacial Orthop 2007;132:332-9) PMID:17826601

Maxillary anterior ridge augmentation with recombinant human bone morphogenetic protein 2.

PubMed

Edmunds, Ryan K; Mealey, Brian L; Mills, Michael P; Thoma, Daniel S; Schoolfield, John; Cochran, David L; Mellonig, Jim

2014-01-01

No human studies exist on the use of recombinant human bone morphogenetic protein 2 (rhBMP-2) on an absorbable collagen sponge (ACS) as a sole graft material for lateral ridge augmentation in large ridge defect sites. This series evaluates the treatment outcome of maxillary anterior lateral ridge augmentation with rhBMP-2/ACS. Twenty patients were treated with rhBMP-2/ACS and fixation screws for space maintenance. Cone beam volumetric tomography measurements were used to determine gain in ridge width, and a bone core biopsy was obtained. The mean horizontal ridge gain was 1.2 mm across sites, and every site gained width.

Low Probability of Intercept Laser Range Finder

DTIC Science & Technology

2017-07-19

time of arrival, and it may also include wavelength, pulse width, and pulse repetition frequency (PRF). Second photodetector 38 in conjunction with... conjunction with lens 32 and telescope 36 that can correct for turbulence along the free space path. [0024] In all embodiments, the time interval

Balance functions reexamined

NASA Astrophysics Data System (ADS)

Bialas, A.

2011-02-01

The idea of glue clusters, i.e., short-range correlations in the quark-gluon plasma close to freeze-out, is used to estimate the width of balance functions in momentum space. A good agreement is found with the recent measurements of the STAR Collaboration for central Au-Au collisions.

Adhesive contact of a rigid circular cylinder to a soft elastic substrate--the role of surface tension.

PubMed

Liu, Tianshu; Jagota, Anand; Hui, Chung-Yuen

2015-05-21

This article studies the effects of surface tension on the adhesive contact mechanics of a long rigid cylinder on an infinite half space comprising an incompressible elastic material. We present an exact solution based on small strain theory. The relationship between the indentation force and contact width was found to depend on a single dimensionless parameter ω = σ/[4(μR)(2/3)(W(ad)/2π)(1/3'), where R is the cylinder radius, Wad is the interfacial work of adhesion, and σ and μ are the surface tension and shear modulus of the half space, respectively. For small ω the solution reduces to the classical Johnson-Kendall-Roberts (JKR) theory, whereas for large ω the solution reduces to the small slope version of the Young-Dupre equation. The pull-off phenomenon was carefully examined and it was found that the contact width at pull-off reduces to zero when surface tension is larger than a critical value.

Improved Miniaturized Linear Ion Trap Mass Spectrometer Using Lithographically Patterned Plates and Tapered Ejection Slit

NASA Astrophysics Data System (ADS)

Tian, Yuan; Decker, Trevor K.; McClellan, Joshua S.; Bennett, Linsey; Li, Ailin; De la Cruz, Abraham; Andrews, Derek; Lammert, Stephen A.; Hawkins, Aaron R.; Austin, Daniel E.

2018-02-01

We present a new two-plate linear ion trap mass spectrometer that overcomes both performance-based and miniaturization-related issues with prior designs. Borosilicate glass substrates are patterned with aluminum electrodes on one side and wire-bonded to printed circuit boards. Ions are trapped in the space between two such plates. Tapered ejection slits in each glass plate eliminate issues with charge build-up within the ejection slit and with blocking of ions that are ejected at off-nominal angles. The tapered slit allows miniaturization of the trap features (electrode size, slit width) needed for further reduction of trap size while allowing the use of substrates that are still thick enough to provide ruggedness during handling, assembly, and in-field applications. Plate spacing was optimized during operation using a motorized translation stage. A scan rate of 2300 Th/s with a sample mixture of toluene and deuterated toluene (D8) and xylenes (a mixture of o-, m-, p-) showed narrowest peak widths of 0.33 Th (FWHM).

Influence of two-stream relativistic electron beam parameters on the space-charge wave with broad frequency spectrum formation

NASA Astrophysics Data System (ADS)

Alexander, LYSENKO; Iurii, VOLK

2018-03-01

We developed a cubic non-linear theory describing the dynamics of the multiharmonic space-charge wave (SCW), with harmonics frequencies smaller than the two-stream instability critical frequency, with different relativistic electron beam (REB) parameters. The self-consistent differential equation system for multiharmonic SCW harmonic amplitudes was elaborated in a cubic non-linear approximation. This system considers plural three-wave parametric resonant interactions between wave harmonics and the two-stream instability effect. Different REB parameters such as the input angle with respect to focusing magnetic field, the average relativistic factor value, difference of partial relativistic factors, and plasma frequency of partial beams were investigated regarding their influence on the frequency spectrum width and multiharmonic SCW saturation levels. We suggested ways in which the multiharmonic SCW frequency spectrum widths could be increased in order to use them in multiharmonic two-stream superheterodyne free-electron lasers, with the main purpose of forming a powerful multiharmonic electromagnetic wave.

Microgravity

NASA Image and Video Library

2000-01-30

Engineers from NASA's Glen Research Center demonstrate the access to one of the experiment racks plarned for the U.S. Destiny laboratory module on the International Space Station (ISS). This mockup has the full diameter, full corridor width, and half the length of the module. The mockup includes engineering mockups of the Fluids and Combustion Facility being developed by NASA's Glenn Research Center. (The full module will be six racks long; the mockup is three racks long). Photo credit: NASA/Marshall Space Flight Center (MSFC)

Rapidly-Indexing Incremental-Angle Encoder

NASA Technical Reports Server (NTRS)

Christon, Philip R.; Meyer, Wallace W.

1989-01-01

Optoelectronic system measures relative angular position of shaft or other device to be turned, also measures absolute angular position after device turned through small angle. Relative angular position measured with fine resolution by optoelectronically counting finely- and uniformly-spaced light and dark areas on encoder disk as disk turns past position-sensing device. Also includes track containing coarsely- and nonuniformly-spaced light and dark areas, angular widths varying in proportion to absolute angular position. This second track provides gating and indexing signal.

A Novel, Free-Space Optical Interconnect Employing Vertical-Cavity Surface Emitting Laser Diodes and InGaAs Metal-Semiconductor-Metal Photodetectors for Gbit/s RF/Microwave Systems

NASA Technical Reports Server (NTRS)

Savich, Gregory R.; Simons, Rainee N.

2006-01-01

Emerging technologies and continuing progress in vertical-cavity surface emitting laser (VCSEL) diode and metal-semiconductor-metal (MSM) photodetector research are making way for novel, high-speed forms of optical data transfer in communication systems. VCSEL diodes operating at 1550 nm have only recently become commercially available, while MSM photodetectors are pushing the limits of contact lithography with interdigitated electrode widths reaching sub micron levels. We propose a novel, free-space optical interconnect operating at about 1Gbit/s utilizing VCSEL diodes and MSM photodetectors. We report on development, progress, and current work, which are as follows: first, analysis of the divergent behavior of VCSEL diodes for coupling to MSM photodetectors with a 50 by 50 m active area and second, the normalized frequency response of the VCSEL diode as a function of the modulating frequency. Third, the calculated response of MSM photodetectors with varying electrode width and spacing on the order of 1 to 3 m as well as the fabrication and characterization of these devices. The work presented here will lead to the formation and characterization of a fully integrated 1Gbit/s free-space optical interconnect at 1550 nm and demonstrates both chip level and board level functionality for RF/microwave digital systems.

Momentum-space structure of quasielastic spin fluctuations in Ce 3Pd 20Si 6

DOE PAGES

Portnichenko, P. Y.; Cameron, A. S.; Surmach, M. A.; ...

2015-03-13

Surrounded by heavy-fermion metals, Ce 3Pd 20Si 6 is one of the heaviest-electron systems known to date. Here we used high-resolution neutron spectroscopy to observe low-energy magnetic scattering from a single crystal of this compound in the paramagnetic state. We investigated its temperature dependence and distribution in momentum space, which was not accessible in earlier measurements on polycrystalline samples. At low temperatures, a quasielastic magnetic response with a half-width Γ ≈ 0.1 meV persists with varying intensity all over the Brillouin zone. It forms a broad hump centered at the (111) scattering vector, surrounded by minima of intensity at (002),more » (220), and equivalent wave vectors. The momentum-space structure distinguishes this signal from a simple crystal-field excitation at 0.31 meV, suggested previously, and rather lets us ascribe it to short-range dynamical correlations between the neighboring Ce ions, mediated by the itinerant heavy f electrons via the Ruderman-Kittel-Kasuya-Yosida mechanism. With increasing temperature, the energy width of the signal follows the conventional T 1/2 law, Γ(T)=Γ0+A√T. Lastly, the momentum-space symmetry of the quasielastic response suggests that it stems from the simple-cubic Ce sublattice occupying the 8c Wyckoff site, whereas the crystallographically inequivalent 4a site remains magnetically silent in this material.« less

Multiple layer insulation cover

DOEpatents

Farrell, James J.; Donohoe, Anthony J.

1981-11-03

A multiple layer insulation cover for preventing heat loss in, for example, a greenhouse, is disclosed. The cover is comprised of spaced layers of thin foil covered fabric separated from each other by air spaces. The spacing is accomplished by the inflation of spaced air bladders which are integrally formed in the cover and to which the layers of the cover are secured. The bladders are inflated after the cover has been deployed in its intended use to separate the layers of the foil material. The sizes of the material layers are selected to compensate for sagging across the width of the cover so that the desired spacing is uniformly maintained when the cover has been deployed. The bladders are deflated as the cover is stored thereby expediting the storage process and reducing the amount of storage space required.

\\Space: A new code to estimate \\temp, \\logg, and elemental abundances

NASA Astrophysics Data System (ADS)

Boeche, C.

2016-09-01

\\Space is a FORTRAN95 code that derives stellar parameters and elemental abundances from stellar spectra. To derive these parameters, \\Space does not measure equivalent widths of lines nor it uses templates of synthetic spectra, but it employs a new method based on a library of General Curve-Of-Growths. To date \\Space works on the wavelength range 5212-6860 Å and 8400-8921 Å, and at the spectral resolution R=2000-20000. Extensions of these limits are possible. \\Space is a highly automated code suitable for application to large spectroscopic surveys. A web front end to this service is publicly available at http://dc.g-vo.org/SP_ACE together with the library and the binary code.

Internal shim

DOEpatents

Barth, Clyde H.; Blizinski, Theodore W.

2003-05-13

An internal shim used to accurately measure spaces in conjunction with a standard small probe has a shim top and a chassis. The internal shim is adjustably fixed within the space to be measured using grippers that emerge from the chassis and which are controlled by an arm pivotably attached to the shim top. A standard small probe passes through the shim along guides on the chassis and measures the distance between the exterior of the chassis and the boundary. By summing the measurements on each side of the chassis and the width of the chassis, the dimension of the space can be determined to within 0.001 inches.

The Structure of Chariklo’s Rings from Stellar Occultations

NASA Astrophysics Data System (ADS)

Bérard, D.; Sicardy, B.; Camargo, J. I. B.; Desmars, J.; Braga-Ribas, F.; Ortiz, J.-L.; Duffard, R.; Morales, N.; Meza, E.; Leiva, R.; Benedetti-Rossi, G.; Vieira-Martins, R.; Gomes Júnior, A.-R.; Assafin, M.; Colas, F.; Dauvergne, J.-L.; Kervella, P.; Lecacheux, J.; Maquet, L.; Vachier, F.; Renner, S.; Monard, B.; Sickafoose, A. A.; Breytenbach, H.; Genade, A.; Beisker, W.; Bath, K.-L.; Bode, H.-J.; Backes, M.; Ivanov, V. D.; Jehin, E.; Gillon, M.; Manfroid, J.; Pollock, J.; Tancredi, G.; Roland, S.; Salvo, R.; Vanzi, L.; Herald, D.; Gault, D.; Kerr, S.; Pavlov, H.; Hill, K. M.; Bradshaw, J.; Barry, M. A.; Cool, A.; Lade, B.; Cole, A.; Broughton, J.; Newman, J.; Horvat, R.; Maybour, D.; Giles, D.; Davis, L.; Paton, R. A.; Loader, B.; Pennell, A.; Jaquiery, P.-D.; Brillant, S.; Selman, F.; Dumas, C.; Herrera, C.; Carraro, G.; Monaco, L.; Maury, A.; Peyrot, A.; Teng-Chuen-Yu, J.-P.; Richichi, A.; Irawati, P.; De Witt, C.; Schoenau, P.; Prager, R.; Colazo, C.; Melia, R.; Spagnotto, J.; Blain, A.; Alonso, S.; Román, A.; Santos-Sanz, P.; Rizos, J.-L.; Maestre, J.-L.; Dunham, D.

2017-10-01

Two narrow and dense rings (called C1R and C2R) were discovered around the Centaur object (10199) Chariklo during a stellar occultation observed on 2013 June 3. Following this discovery, we planned observations of several occultations by Chariklo’s system in order to better characterize the physical properties of the ring and main body. Here, we use 12 successful occulations by Chariklo observed between 2014 and 2016. They provide ring profiles (physical width, opacity, edge structure) and constraints on the radii and pole position. Our new observations are currently consistent with the circular ring solution and pole position, to within the ±3.3 km formal uncertainty for the ring radii derived by Braga-Ribas et al. The six resolved C1R profiles reveal significant width variations from ˜5 to 7.5 km. The width of the fainter ring C2R is less constrained, and may vary between 0.1 and 1 km. The inner and outer edges of C1R are consistent with infinitely sharp boundaries, with typical upper limits of one kilometer for the transition zone between the ring and empty space. No constraint on the sharpness of C2R’s edges is available. A 1σ upper limit of ˜20 m is derived for the equivalent width of narrow (physical width < 4 km) rings up to distances of 12,000 km, counted in the ring plane.

Aerial view of the Kennedy Space Center Visitor Center

NASA Technical Reports Server (NTRS)

1998-01-01

The Kennedy Space Center Visitor Complex, shown in this aerial view looking south, sprawls across 70 acres on Florida's Space Coast. It is located off State Road 405, NASA Parkway, six miles inside the Space Center entrance. SR 405 can be seen at the bottom of the photo. Just above the roadway, from left, can be seen the Shuttle/Gantry mockup, the Post Show Dome, the Astronaut Memorial, and to the far right, the Center for Space Education. Behind the Memorial are a cluster of buildings that include the Theater Complex, Cafeteria, Space Flight Exhibit Building, Souvenir Sales Building, Spaceport Central, and Ticket Pavilion. At the upper right of the site is a display of rockets that have played a significant role in the growth of the space program. Parking lots span the width of the complex on the south side.

Effect of channel size on sweet potato storage root enlargement in the Tuskegee University hydroponic nutrient film system

NASA Technical Reports Server (NTRS)

Morris, Carlton E.; Martinez, Edwin; Bonsi, C. K.; Mortley, Desmond G.; Hill, Walter A.; Ogbuehi, Cyriacus R.; Loretan, Phil A.

1989-01-01

The potential of the sweet potato as a food source for future long term manned space missions is being evaluated for NASA's Controlled Ecological Life Support Systems (CELSS) program. Sweet potatoes have been successfully grown in a specially designed Tuskegee University nutrient film technique (TU NFT) system. This hydroponic system yielded storage roots as high as 1790 g/plant fresh weight. In order to determine the effect of channel size on the yield of sweet potatoes, the width and depth of the growing channels were varied in two separate experiments. Widths were studied using the rectangular TU NFT channels with widths of 15 cm (6 in), 30 cm (12 in) and 45 cm (18 in). Channel depths of 5 cm (2 in), 10 cm (4 in), and 15 cm (6 in) were studied using a standard NASA fan shaped Biomass Production Chamber (BPC) channel. A comparison of preliminary results indicated that, except for storage root number, the growth and yield of sweet potatoes were not affected by channel width. Storage root yield was affected by channel depth although storage root number and foliage growth were not. Both experiments are being repeated.

Comparing perceived auditory width to the visual image of a performing ensemble in contrasting bi-modal environmentsa)

PubMed Central

Valente, Daniel L.; Braasch, Jonas; Myrbeck, Shane A.

2012-01-01

Despite many studies investigating auditory spatial impressions in rooms, few have addressed the impact of simultaneous visual cues on localization and the perception of spaciousness. The current research presents an immersive audiovisual environment in which participants were instructed to make auditory width judgments in dynamic bi-modal settings. The results of these psychophysical tests suggest the importance of congruent audio visual presentation to the ecological interpretation of an auditory scene. Supporting data were accumulated in five rooms of ascending volumes and varying reverberation times. Participants were given an audiovisual matching test in which they were instructed to pan the auditory width of a performing ensemble to a varying set of audio and visual cues in rooms. Results show that both auditory and visual factors affect the collected responses and that the two sensory modalities coincide in distinct interactions. The greatest differences between the panned audio stimuli given a fixed visual width were found in the physical space with the largest volume and the greatest source distance. These results suggest, in this specific instance, a predominance of auditory cues in the spatial analysis of the bi-modal scene. PMID:22280585

CD-measurement technique for hole patterns on stencil mask

NASA Astrophysics Data System (ADS)

Ishikawa, Mikio; Yusa, Satoshi; Takikawa, Tadahiko; Fujita, Hiroshi; Sano, Hisatake; Hoga, Morihisa; Hayashi, Naoya

2004-12-01

EB lithography has a potential to successfully form hole patterns as small as 80 nm with a stencil mask. In a previous paper we proposed a technique using a HOLON dual-mode critical dimension (CD) SEM ESPA-75S in the transmission mode for CD measurement of line-and-space patterns on a stencil mask. In this paper we extend our effort of developing a CD measurement technique to contact hole features and determine it in comparison of measured values between features on mask and those printed on wafer. We have evaluated the width method and the area methods using designed 80-500 nm wide contact hole patterns on a large area membrane mask and their resist images on wafer printed by a LEEPL3000. We find that 1) the width method and the area methods show an excellent mask-wafer correlation for holes over 110 nm, and 2) the area methods show a better mask-wafer correlation than the width method does for holes below 110 nm. We conclude that the area calculated from the transmission SEM image is more suitable in defining the hole dimensions than the width for contact holes on a stencil mask.

Evaluation of the need for longitudinal median joints in bridge decks on dual structures.

DOT National Transportation Integrated Search

2015-09-01

The primary objective of this project was to determine the effect of bridge width on deck cracking in bridges. Other parameters, : such as bridge skew, girder spacing and type, abutment type, pier type, and number of bridge spans, were also studied. ...

18 CFR Appendix A to Part 2 - Guidance for Determining the Acceptable Construction Area for Replacements

Code of Federal Regulations, 2011 CFR

2011-04-01

.... Typical work spaces are: Item Typical extra area (width/length) Two lane road (bored) 25-50 by 100 feet. Four lane road (bored) 50 by 100 feet. Major river (wet cut) 100 by 200 feet. Intermediate stream (wet...

CHIMNEY FOR BOILING WATER REACTOR

DOEpatents

Petrick, M.

1961-08-01

A boiling-water reactor is described which has vertical fuel-containing channels for forming steam from water. Risers above the channels increase the head of water radially outward, whereby water is moved upward through the channels with greater force. The risers are concentric and the radial width of the space between them is somewhat small. There is a relatively low rate of flow of water up through the radially outer fuel-containing channels, with which the space between the risers is in communication. (AE C)

A New Approach to Scaling Channel Width in Bedrock Rivers and its Implications for Modeling Fluvial Incision

NASA Astrophysics Data System (ADS)

Finnegan, N. J.; Roe, G.; Montgomery, D. R.; Hallet, B.

2004-12-01

The fundamental role of bedrock channel incision on the evolution of mountainous topography has become a central concept in tectonic geomorphology over the past decade. During this time the stream power model of bedrock river incision has immerged as a valuable tool for exploring the dynamics of bedrock river incision in time and space. In most stream power analyses, river channel width--a necessary ingredient for calculating power or shear stress per unit of bed area--is assumed to scale solely with discharge. However, recent field-based studies provide evidence for the alternative view that channel width varies locally, much like channel slope does, in association with spatial changes in rock uplift rate and erodibility. This suggests that simple scaling relations between width and discharge, and hence estimates of stream power, don't apply in regions where rock uplift and erodibility vary spatially. It also highlights the need for an alternative to the traditional assumptions of hydraulic geometry to further investigation of the coupling between bedrock river incision and tectonic processes. Based on Manning's equation, basic mass conservation principles, and an assumption of self-similarity for channel cross sections, we present a new relation for scaling the steady-state width of bedrock river channels as a function of discharge (Q), channel slope (S), and roughness (Ks): W \\propto Q3/8S-3/16Ks1/16. In longitudinally simple, uniform-concavity rivers from the King Range in coastal Northern California, the model emulates traditional width-discharge relations that scale channel width with the square root of discharge. More significantly, our relation describes river width trends for the Yarlung Tsangpo in SE Tibet and the Wenatchee River in the Washington Cascades, both rivers that narrow considerably as they incise terrain with spatially varied rock uplift rates and/or lithology. We suggest that much of observed channel width variability is a simple consequence of the tendency for water to flow faster in steeper reaches and therefore maintain smaller channel cross sections. We demonstrate that using conventional scaling relations for bedrock channel width can significantly underestimate stream power variability in bedrock channels, and that our model improves estimates of spatial patterns of bedrock incision rates.

16 CFR 305.12 - Labeling for central air conditioners, heat pumps, and furnaces.

Code of Federal Regulations, 2013 CFR

2013-01-01

... pumps, and furnaces. (a) Layout. All energy labels for central air conditioners, heat pumps, and... end of this part illustrating the basic layout. All positioning, spacing, type sizes, and line widths... calculated for heating Region IV for the standardized design heating requirement nearest the capacity...

--No Title--

Science.gov Websites

; .fc-day-grid, .fc-scroller > .fc-time-grid { position: relative; /* re-scope all positions */ width -space: nowrap; overflow: hidden; } .fc-day-grid-event .fc-time { font-weight: bold; } /* resizer (cursor will be over the time grid */ } .fc-agenda-view .fc-day-grid .fc-row { min-height: 3em; /* all-day

Modeling transient gain dynamics in a cladding-pumped Yb-doped fiber ampliefier pulsed at low repetition rates

NASA Technical Reports Server (NTRS)

Valley, G. C.; Wright, M.

2001-01-01

Simulations of 1-50 kHz repetition rate, pulsed Yb-fiber amplifiers show peak powers to 10 kW with half-widths < 30 ns, consistent with commercial amplifier performance. This device is a potential source for deep space-communication.

Fixed-flexion view X-ray of the knee superior in detection and follow-up of knee osteoarthritis

PubMed Central

Kan, Hiroyuki; Arai, Yuji; Kobayashi, Masashi; Nakagawa, Shuji; Inoue, Hiroaki; Hino, Manabu; Komaki, Shintaro; Ikoma, Kazuya; Ueshima, Keiichiro; Fujiwara, Hiroyoshi; Yokota, Isao; Kubo, Toshikazu

2017-01-01

Abstract A fixed flexion view (FFV) is useful for evaluating joint space when assessing the severity of osteoarthritis (OA) of the knee. We analyzed changes in joint space revealed by standing extended view (SEV) and FFV over a mean 4 years, to compare both views on their capacity to measure joint space width accurately at particular time points during follow-up. SEV and FFV images were acquired in patients with knee OA. The 81 patients (157 knees) followed up for ≥24 months were selected as study subjects. Medial joint space widths (MJSW), Kellgren–Lawrence (KL) grades, and reductions in MJSW on SEV (ΔSEV) and FFV (ΔFFV) were compared in knees evaluated by SEV and FFV. At both time-points, mean MJSW was significantly lower by FFV than by SEV. Mean MJSW was significantly lower at follow-up than at first examination by both SEV and FFV. At both time-points, the KL grade was higher by FFV than by SEV group. The ΔFFV was significantly greater than the ΔSEV. ΔSEV did not differ significantly among KL grades, but ΔFFV was significantly greater in patients with KL grade II than in patients with other KL grades. FFV is not only useful for evaluating joint space in knees with OA, but also for accurately evaluating the progression of OA. The risk of rapid progression of knee OA may be higher in patients with KL grade II, as determined by FFV. FFV may be superior to SEV in determining appropriate treatment strategies for knee OA. PMID:29245351

Mass discharge in a tracer plume: Evaluation of the Theissen Polygon Method

PubMed Central

Mackay, Douglas M.; Einarson, Murray D.; Kaiser, Phil M.; Nozawa-Inoue, Mamie; Goyal, Sham; Chakraborty, Irina; Rasa, Ehsan; Scow, Kate M.

2013-01-01

A tracer plume was created within a thin aquifer by injection for 299 days of two adjacent “sub-plumes” to represent one type of plume heterogeneity encountered in practice. The plume was monitored by snapshot sampling of transects of fully screened wells. The mass injection rate and total mass injected were known. Using all wells in each transect (0.77 m well spacing, 1.4 points/m2 sampling density), the Theissen Polygon Method (TPM) yielded apparently accurate mass discharge (Md) estimates at 3 transects for 12 snapshots. When applied to hypothetical sparser transects using subsets of the wells with average spacing and sampling density from 1.55 to 5.39 m and 0.70 to 0.20 points/m2, respectively, the TPM accuracy depended on well spacing and location of the wells in the hypothesized transect with respect to the sub-plumes. Potential error was relatively low when the well spacing was less than the widths of the sub-plumes (> 0.35 points/m2). Potential error increased for well spacing similar to or greater than the sub-plume widths, or when less than 1% of the plume area was sampled. For low density sampling of laterally heterogeneous plumes, small changes in groundwater flow direction can lead to wide fluctuations in Md estimates by the TPM. However, sampling conducted when flow is known or likely to be in a preferred direction can potentially allow more useful comparisons of Md over multiyear time frames, such as required for performance evaluation of natural attenuation or engineered remediation systems. PMID:22324777

KSC-98PC-1058

NASA Image and Video Library

1998-08-06

The Kennedy Space Center Visitor Complex, shown in this aerial view looking south, sprawls across 70 acres on Florida's Space Coast. It is located off State Road 405, NASA Parkway, six miles inside the Space Center entrance. SR 405 can be seen at the bottom of the photo. Just above the roadway, from left, can be seen the Shuttle/Gantry mockup, the Post Show Dome, the Astronaut Memorial, and to the far right, the Center for Space Education. Behind the Memorial are a cluster of buildings that include the Theater Complex, Cafeteria, Space Flight Exhibit Building, Souvenir Sales Building, Spaceport Central, and Ticket Pavilion. At the upper right of the site is a display of rockets that have played a significant role in the growth of the space program. Parking lots span the width of the complex on the south side.

Laser backscattered from partially convex targets of large sizes in random media for E-wave polarization.

PubMed

El-Ocla, Hosam

2006-08-01

The characteristics of a radar cross section (RCS) of partially convex targets with large sizes up to five wavelengths in free space and random media are studied. The nature of the incident wave is an important factor in remote sensing and radar detection applications. I investigate the effects of beam wave incidence on the performance of RCS, drawing on the method I used in a previous study on plane-wave incidence. A beam wave can be considered a plane wave if the target size is smaller than the beam width. Therefore, to have a beam wave with a limited spot on the target, the target size should be larger than the beam width (assuming E-wave incidence wave polarization. The effects of the target configuration, random medium parameters, and the beam width on the laser RCS and the enhancement in the radar cross section are numerically analyzed, resulting in the possibility of having some sort of control over radar detection using beam wave incidence.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Phillips, Benjamin R.; Baldridge, W. Scott; Gable, Carl W.

Finite volume calculations of the flow of rhyolite are presented to investigate the fate of viscous magmas flowing in planar fractures with realistic length to width ratios of up to 2500:1. Heat and mass transfer for a melt with a temperature dependent viscosity and the potential to undergo phase change are considered. Magma driving pressures and dike widths are chosen to satisfy simple elastic considerations. These models are applied within a parameter space relevant to the Banco Bonito rhyolite flow, Valles caldera, New Mexico. We estimate a maximum eruption duration for the event of ~200 days, realized at a minimummore » possible dike width of 5-6 m and driving pressure of 7-8 MPa. Simplifications in the current model may warrant scaling of these results. However, we demonstrate the applicability of our model to magma dynamics issues and suggest that such models may be used to infer information about both the timing of an eruption and the evolution of the associated magma source.« less

Digital model as an alternative to plaster model in assessment of space analysis

PubMed Central

Kumar, A. Anand; Phillip, Abraham; Kumar, Sathesh; Rawat, Anuradha; Priya, Sakthi; Kumaran, V.

2015-01-01

Introduction: Digital three-dimensional models are widely used for orthodontic diagnosis. The purpose of this study was to appraise the accuracy of digital models obtained from computer-aided design/computer-aided manufacturing (CAD/CAM) and cone-beam computed tomography (CBCT) for tooth-width measurements and the Bolton analysis. Materials and Methods: Digital models (CAD/CAM, CBCT) and plaster model were made for each of 50 subjects. Tooth-width measurements on the digital models (CAD/CAM, CBCT) were compared with those on the corresponding plaster models. The anterior and overall Bolton ratios were calculated for each participant and for each method. The paired t-test was applied to determine the validity. Results: Tooth-width measurements, anterior, and overall Bolton ratio of digital models of CAD/CAM and CBCT did not differ significantly from those on the plaster models. Conclusion: Hence, both CBCT and CAD/CAM are trustable and promising technique that can replace plaster models due to its overwhelming advantages. PMID:26538899

Effects of cloud size and cloud particles on satellite-observed reflected brightness

NASA Technical Reports Server (NTRS)

Reynolds, D. W.; Mckee, T. B.; Danielson, K. S.

1978-01-01

Satellite observations allowed obtaining data on the visible brightness of cumulus clouds over South Park, Colorado, while aircraft observations were made in cloud to obtain the drop size distributions and liquid water content of the cloud. Attention is focused on evaluating the relationship between cloud brightness, horizontal dimension, and internal microphysical structure. A Monte Carlo cloud model for finite clouds was run using different distributions of drop sizes and numbers, while varying the cloud depth and width to determine how theory would predict what the satellite would view from its given location in space. Comparison of these results to the satellite observed reflectances is presented. Theoretical results are found to be in good agreement with observations. For clouds of optical thickness between 20 and 60, monitoring cloud brightness changes in clouds of uniform depth and variable width gives adequate information about a cloud's liquid water content. A cloud having a 10:1 width to depth ratio is almost reaching its maximum brightness for a specified optical thickness.

Method of creating additional parking spaces in the “Tudor Vladimirescu” University Campus

NASA Astrophysics Data System (ADS)

Maftei, A.; Dontu, A. I.; Sachelarie, A.; Budeanu, B.

2016-08-01

The increasing number of vehicles in recent years has yielded a lot of problems regarding road vehicle infrastructure in residential areas, especially in towns. The problem is that roads dimensioning and especially parking spaces are under dimensioned for the current number of vehicles in use. The current paper addresses the problem of the lack of parking spaces in the “Tudor Vladimirescu” University Campus. The Campus infrastructure was build in the early 1970's and has received only a slight upgrade regarding access roads width, the access roads that were enlarged were Prof. Vasile Petrescu Street and Prof. Gheorghe Alexa Street. On the first specified road, parking spaces at 45 degrees were created, but this does not cover the number of needed parking spaces.

The phase-space dependence of fast-ion interaction with tearing modes

DOE PAGES

Heidbrink, William W.; Bardoczi, Laszlo; Collins, Cami S.; ...

2018-03-19

Modulation of various neutral beam sources probes the interaction of fast ions with tearing modes (TM) in the DIII-D tokamak. As measured by electron cyclotron emission, the (m,n) = (2,1) tearing modes have an island width of ~8 cm and change phase 180 at the q = 2 surface. (Here, m is the poloidal mode number and n is the toroidal mode number.) Deuterium neutral beam injection by six sources with differing injection geometries produces the fast ions. To study the interaction in different parts of phase space, on successive discharges, one of the six sources is modulated at 20more » Hz to populate different fast-ion orbits. The modulation only changes the island width by a few millimeters, implying that any fast-ion effect on mode stability is below detection limits. When compared to the expected signals in the absence of TM-induced transport, both the average and modulated neutron signals deviate, implying that fast-ion transport occurs in much of phase space. Fast-ion D-α (FIDA) measurements detect reductions in signal at wavelengths that are sensitive to counter-passing ions. Neutral particle analyzer data imply poor confinement of trapped fast ions. Lastly, calculations of the expected fast-ion transport that use measured TM properties successfully reproduce the data.« less

Interpretation of inverted photocurrent transients in organic lead halide perovskite solar cells: proof of the field screening by mobile ions and determination of the space charge layer widths

DOE PAGES

Belisle, Rebecca A.; Nguyen, William H.; Bowring, Andrea R.; ...

2017-01-01

In Methyl Ammonium Lead Iodide (MAPI) perovskite solar cells, screening of the built-in field by mobile ions has been proposed as part of the cause of the large hysteresis observed in the current/voltage scans in many cells. Here, we show that photocurrent transients measured immediately (e.g. 100 μs) after a voltage step can provide direct evidence that this field screening exists. Just after a step to forward bias, the photocurrent transients are reversed in sign (i.e. inverted), and the magnitude of the inverted transients can be used to find an upper bound on the width of the space charge layersmore » adjacent to the electrodes. This in turn provides a lower bound on the mobile charge concentration, which we find to be ≳1 x 10 17 cm -3. Using a new photocurrent transient experiment, we show that the space charge layer thickness remains approximately constant as a function of bias, as expected for mobile ions in a solid electrolyte. We also discuss additional characteristics of the inverted photocurrent transients that imply either an unusually stable deep trapping, or a photo effect on the mobile ion conductivity.« less

Interpretation of inverted photocurrent transients in organic lead halide perovskite solar cells: proof of the field screening by mobile ions and determination of the space charge layer widths

DOE Office of Scientific and Technical Information (OSTI.GOV)

Belisle, Rebecca A.; Nguyen, William H.; Bowring, Andrea R.

In Methyl Ammonium Lead Iodide (MAPI) perovskite solar cells, screening of the built-in field by mobile ions has been proposed as part of the cause of the large hysteresis observed in the current/voltage scans in many cells. Here, we show that photocurrent transients measured immediately (e.g. 100 μs) after a voltage step can provide direct evidence that this field screening exists. Just after a step to forward bias, the photocurrent transients are reversed in sign (i.e. inverted), and the magnitude of the inverted transients can be used to find an upper bound on the width of the space charge layersmore » adjacent to the electrodes. This in turn provides a lower bound on the mobile charge concentration, which we find to be ≳1 x 10 17 cm -3. Using a new photocurrent transient experiment, we show that the space charge layer thickness remains approximately constant as a function of bias, as expected for mobile ions in a solid electrolyte. We also discuss additional characteristics of the inverted photocurrent transients that imply either an unusually stable deep trapping, or a photo effect on the mobile ion conductivity.« less

The phase-space dependence of fast-ion interaction with tearing modes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Heidbrink, William W.; Bardoczi, Laszlo; Collins, Cami S.

Modulation of various neutral beam sources probes the interaction of fast ions with tearing modes (TM) in the DIII-D tokamak. As measured by electron cyclotron emission, the (m,n) = (2,1) tearing modes have an island width of ~8 cm and change phase 180 at the q = 2 surface. (Here, m is the poloidal mode number and n is the toroidal mode number.) Deuterium neutral beam injection by six sources with differing injection geometries produces the fast ions. To study the interaction in different parts of phase space, on successive discharges, one of the six sources is modulated at 20more » Hz to populate different fast-ion orbits. The modulation only changes the island width by a few millimeters, implying that any fast-ion effect on mode stability is below detection limits. When compared to the expected signals in the absence of TM-induced transport, both the average and modulated neutron signals deviate, implying that fast-ion transport occurs in much of phase space. Fast-ion D-α (FIDA) measurements detect reductions in signal at wavelengths that are sensitive to counter-passing ions. Neutral particle analyzer data imply poor confinement of trapped fast ions. Lastly, calculations of the expected fast-ion transport that use measured TM properties successfully reproduce the data.« less

Graphene Oxide: A Perfect Material for Spatial Light Modulation Based on Plasma Channels

PubMed Central

Tan, Chao; Wu, Xinghua; Wang, Qinkai; Tang, Pinghua; Shi, Xiaohui; Zhan, Shiping; Xi, Zaifang; Fu, Xiquan

2017-01-01

The graphene oxide (GO) is successfully prepared from a purified natural graphite through a pressurized oxidation method. We experimentally demonstrate that GO as an optical media can be used for spatial light modulation based on plasma channels induced by femtosecond pulses. The modulated beam exhibits good propagation properties in free space. It is easy to realize the spatial modulation on the probe beam at a high concentration of GO dispersion solutions, high power and smaller pulse width of the pump beam. We also find that the spatial modulation on the probe beam can be conveniently adjusted through the power and pulse width of pump lasers, dispersion solution concentration. PMID:28772712

KOLMOGOROV WIDTHS IN THE SPACE {\\tilde L}_q OF THE CLASSES {\\tilde W}_p^{\\overline \\alpha} AND {\\tilde H}_p^{\\overline \\alpha} OF PERIODIC FUNCTIONS OF SEVERAL VARIABLES

NASA Astrophysics Data System (ADS)

Galeev, È. M.

1986-04-01

The author finds the order of the Kolmogorov widths d_N({\\tilde W}_p^{\\overline \\alpha} = \\bigcap_{i=1}^m {\\tilde W}_p^{\\alpha^i}, {\\tilde L}_q) for all 1 < p,q < \\infty, where {\\tilde W}_p^\\alpha is the class of periodic functions of several variables determined by a Weyl mixed fractional derivative, and d_N({\\tilde H}_p^{\\overline \\alpha} = \\bigcap_{i=1}^m {\\tilde H}_p^{\\alpha^i},{\\tilde L}_q) for p \\ge 2 or q \\ge 2, where {\\tilde H}_p^\\alpha is the class determined by a mixed difference. Bibliography: 28 titles.

Analysis of a unidirectional, symmetric buffer strip laminate with damage

NASA Technical Reports Server (NTRS)

Dharani, L. R.; Goree, J. G.

1984-01-01

A method for predicting the fracture behavior of hybrid buffer strip laminates is presented in which the classical shear-lag model is used to represent the shear stress distribution between adjacent fibers. The method is demonstrated by applying it to a notched graphite/epoxy laminate, and the results show clearly the manner in which the most efficient combination of buffer strip properties can be selected in order to arrest the crack. The ultimate failure stress of the laminate is plotted vs the buffer strip width. It is shown that in the case of graphite-epoxy and S-glass epoxy laminates, the optimum buffer strip spacing to width ratio should be about four to one.

Characterization of the Coupling Between Adjacent Finite Ground Coplanar (FGC) Waveguides

NASA Technical Reports Server (NTRS)

Ponchak, George E.; Katehi, Linda P. B.; Tentzeris, Emmanouil M.

1997-01-01

Coupling between adjacent Finite Ground Coplanar (FGC) waveguides as a function of the line geometry is presented for the first time. A two Dimension-Finite Difference Time Domain (2D-FDTD) analysis and measurements are used to show that the coupling decreases as the line to line separation and the grOUnd plane width increases. Furthermore, it is shown that for a given spacing between the center lines of two FGC lines, the coupling is lower if the ground plane width is smaller Lastly, electric field plots generated from the 2D-FDTD technique are presented which demonstrate a strong slotline mode is established in the coupled FGC line.

Kinetic theory analysis of rarefied gas flow through finite length slots

NASA Technical Reports Server (NTRS)

Raghuraman, P.

1972-01-01

An analytic study is made of the flow a rarefied monatomic gas through a two dimensional slot. The parameters of the problem are the ratios of downstream to upstream pressures, the Knudsen number at the high pressure end (based on slot half width) and the length to slot half width ratio. A moment method of solution is used by assuming a discontinuous distribution function consisting of four Maxwellians split equally in angular space. Numerical solutions are obtained for the resulting equations. The characteristics of the transition regime are portrayed. The solutions in the free molecule limit are systematically lower than the results obtained in that limit by more accurate numerical methods.

Nanoscale patterning of Si surface using SPM scratching

NASA Astrophysics Data System (ADS)

Ogino, T.; Nishimura, S.; Shirakashi, J.

2008-03-01

Nanolithography of Si surface using scanning probe microscopy (SPM) scratching with a diamond-coated tip was systematically investigated at a low force regime below 9 μN. The groove patterns with controlled width and depth could be achieved by adjusting the applied force, scan direction and the number of scan cycles. There was no effect of scan speed on the groove size. The minimum groove width of 10 nm was obtained on Si surfaces. Furthermore, more complex nanostructures such as line and space patterns of 30 nm pith and dot arrays of 2.6×1010 cm-2 density were realized. SPM scratching with a diamond-coated tip allows nanoscale patterning of Si surfaces to be performed simply.

The impact of body habitus on the surgical outcomes of transaxillary single-incision robotic thyroidectomy in papillary thyroid carcinoma patients.

PubMed

Lee, Sohee; Park, Seulkee; Lee, Cho Rok; Son, Haiyoung; Kim, Jungwoo; Kang, Sang-Wook; Jeong, Jong Ju; Nam, Kee-Hyun; Chung, Woong Youn; Park, Cheong Soo

2013-07-01

Robotic applications have achieved safe and precise thyroidectomy with notable cosmetic and functional benefits. This study was designed to document the influence of body habitus on robotic thyroidectomy in papillary thyroid carcinoma (PTC) patients. From July 2009 to February 2010, 352 patients underwent robotic thyroidectomy using a gasless, transaxillary single-incision approach at Yonsei University Health System. Body habitus was described using body mass index category (normal weight, overweight, obese), neck length, shoulder width, and shoulder width to neck length ratios. The impact of body habitus on surgical outcomes was analyzed with respect to operation time, number of retrieved central nodes, bleeding amount, and postoperative complications. Of the 352 patients, 217 underwent less than total thyroidectomy and 135 underwent total thyroidectomy. Operative variables (i.e. operation times, bleeding amounts, and numbers of retrieved central nodes) showed no significant differences between three BMI groups for less than total thyroidectomy. However, total operation and working space times were longer for obese patients during total thyroidectomy. In particular, shoulder width was positively correlated with total operation time, working space time, console time, and number of retrieved central nodes. On the other hand, postoperative complications were not significantly different in the three BMI groups and showed no significant correlation with the other indices of body habitus. Standardized robotic thyroidectomy can be performed safely and feasibly in patients with a large body habitus despite longer operation times.

LEO-ground scintillation measurements with the optical ground station Oberpfaffenhofen and SOTA/OPALS space terminals

NASA Astrophysics Data System (ADS)

Moll, Florian; Kolev, Dimitar; Abrahamson, Matthew; Schmidt, Christopher; Mata Calvo, Ramon; Fuchs, Christian

2016-10-01

The optical satellite-ground channel is turbulent and causes scintillation of the power received by a ground based telescope. Measurements are important to quantify the effect and evaluate common theory. A telescope with 40 cm primary mirror is used to measure the signals from the OPALS terminal on the International Space Station and the SOTA terminal on the SOCRATES satellite. The measurement instrument is a pupil camera from which images are recorded and intensity scintillation index, power scintillation index, probability density function of intensity and intensity correlation width are derived. A preliminary analysis of measurements from three satellite passed is performed, presented and discussed. The intensity scintillation index ranges from 0.25 to 0.03 within elevations of 26 to 66 deg. Power scintillation index varies from 0.08 to 0.006 and correlation width of intensity between 11 and 3 cm. The measurements can be used to estimate the fluctuation dynamics to be expected for a future operational ground receiver. The measurements are compared to model calculations based on the HV5/7-profile. Good agreement is observed to some part in the intensity scintillation index. Agreement is less for the power scintillation index and intensity correlation width. The reason seems to be a reduction of aperture averaging in some sections of the measurements due to increased speckle size. Finally, topics for future work are identified to improve the measurement analysis and deeper investigate the origin of the observed behavior.

Cracking of Beams Strengthened with Externally Bonded SRP Tapes

NASA Astrophysics Data System (ADS)

Krzywoń, Rafał

2017-10-01

Paper discusses strengthening efficiency of relatively new kind of SRP composite based on high strength steel wires. They are made of ultra-high strength steel primarily used in cords of car tires. Through advanced treatment, the mechanical properties of SRP steel are similar to other high carbon cold drawn steels used in construction industry. Strength significantly exceed 2000 MPa, there is no perfect plasticity at yield stress level. Almost linear stress-strain relationship makes SRP steel mechanical properties similar to carbon fibers. Also flexibility and weight ratio of the composite overlay is slightly worse than CFRP strip. Despite these advantages SRP is not as popular as other composites reinforced with fibers of high strength. This is due to the small number of studies of SRP behavior and applicability. Paper shows selected results of the laboratory test of beams strengthened with use of SRP and CFRP externally bonded overlays. Attention has been focused primarily on the phenomenon of cracking. Comparison include the cracking moment, crack width and spacing, coverage of crack zone. Despite the somewhat lower rigidity of SRP tapes, they have a much better adhesion to concrete, so that the crack width is comparable in almost the whole load range. The paper also includes an assessment of the common methods of checking the condition of cracking in relation to the tested SRP strengthening. The paper presents actual calculation procedures to determine the crack spacing and crack width. The discussed formulas are verified with results of provided laboratory tests.

Simultaneous frequency stabilization and high-power dense wavelength division multiplexing (HP-DWDM) using an external cavity based on volume Bragg gratings (VBGs)

NASA Astrophysics Data System (ADS)

Hengesbach, Stefan; Klein, Sarah; Holly, Carlo; Witte, Ulrich; Traub, Martin; Hoffmann, Dieter

2016-03-01

Multiplexing technologies enable the development of high-brightness diode lasers for direct industrial applications. We present a High-Power Dense Wavelength Division Multiplexer (HP-DWDM) with an average channel spacing of 1.7 (1.5) nm and a subsequent external cavity mirror to provide feedback for frequency stabilization and multiplexing in one step. The "self-optimizing" multiplexing unit consists of four reflective Volume Bragg Gratings (VBGs) with 99% diffraction efficiency and seven dielectric mirrors to overlay the radiation of five input channels with an adjustable channel spacing of 1-2 nm. In detail, we focus on the analysis of the overall optical efficiency, the change of the beam parameter product and the spectral width. The performance is demonstrated using five 90 μm multimode 9xx single emitters with M2<=17. Because of the feedback the lateral (multimodal) spatial and angular intensity distribution changes strongly and the beam parameter product decreases by a factor of 1.2 to 1.9. Thereby the angular intensity distribution is more affected than the width of the beam waist. The spectral width per emitter decreases to 3-200 pm (FWHM) depending on the injection current and the reflectance of the feedback mirror (0.75%, 1.5%, 4%, 6% or 8%). The overall optical multiplexing efficiency ranges between 77% and 86%. With some modifications (e.g. enhanced AR-coatings) we expect 90-95%.

Development of control systems for solar water and solar space heating equipment. Choice of heat conducting fluid. Testing

NASA Astrophysics Data System (ADS)

Meyer, H.

1981-11-01

Flat plate collector systems suitable for hot water supply, swimming pool heating, and auxiliary space heating were developed. A control and ready made packaged pipe assembly, adapted to synthetic fluid, was developed. A heat transfer fluid was selected, pumps, safety devices, armatures and seals were tested for their long term performance. External heat exchangers for simple and cascade arrangement of the hot water tanks were tested. It is found that the channel design of a roll bonded absorber has only limited effect on collector performance if the channel width approximates the space between the plates. Systems already installed work satisfactorily.

Microgravity

NASA Image and Video Library

2000-01-30

Engineers from NASA's Glenn Research Center demonstrate the access to one of the experiment racks planned for the U.S. Destiny laboratory module on the International Space Station (ISS). This mockup has the full diameter, full corridor width, and half the length of the module. The mockup includes engineering mockups of the Fluids and Combustion Facility being developed by NASA's Glenn Research Center. (The full module will be six racks long; the mockup is three racks long). Listening at left (coat and patterned tie) is John-David Bartoe, ISS research manager at NASA's Johnson Space Center and a payload specialist on Spacelab 2 mission (1985). Photo credit: NASA/Marshall Space Flight Center (MSFC)

Time-to-space mapping of a continuous light wave with picosecond time resolution based on an electrooptic beam deflection.

PubMed

Hisatake, S; Kobayashi, T

2006-12-25

We demonstrate a time-to-space mapping of an optical signal with a picosecond time resolution based on an electrooptic beam deflection. A time axis of the optical signal is mapped into a spatial replica by the deflection. We theoretically derive a minimum time resolution of the time-to-space mapping and confirm it experimentally on the basis of the pulse width of the optical pulses picked out from the deflected beam through a narrow slit which acts as a temporal window. We have achieved the minimum time resolution of 1.6+/-0.2 ps.

Time-space modal logic for verification of bit-slice circuits

NASA Astrophysics Data System (ADS)

Hiraishi, Hiromi

1996-03-01

The major goal of this paper is to propose a new modal logic aiming at formal verification of bit-slice circuits. The new logic is called as time-space modal logic and its major feature is that it can handle two transition relations: one for time transition and the other for space transition. As for a verification algorithm, a symbolic model checking algorithm of the new logic is shown. This could be applicable to verification of bit-slice microprocessor of infinite bit width and 1D systolic array of infinite length. A simple benchmark result shows the effectiveness of the proposed approach.

Difference between manual and digital measurements of dental arches of orthodontic patients.

PubMed

Jiménez-Gayosso, Sandra Isabel; Lara-Carrillo, Edith; López-González, Saraí; Medina-Solís, Carlo Eduardo; Scougall-Vilchis, Rogelio José; Hernández-Martínez, César Tadeo; Colomé-Ruiz, Gabriel Eduardo; Escoffié-Ramirez, Mauricio

2018-06-01

The objective of this study was to compare the differences between the measurements performed manually to those obtained using a digital model scanner of patients with orthodontic treatment.A cross-sectional study was performed in a sample of 30 study models from patients with permanent dentition who attended a university clinic between January 2010 and December 2015. For the digital measurement, a Maestro 3D Ortho Studio scanner (Italy) was used and Mitutoyo electronic Vernier calipers (Kawasaki, Japan) were used for manual measurement. The outcome variables were the measurements for maxillary intercanine width, mandibular intercanine width, maxillary intermolar width, mandibular intermolar width, overjet, overbite, maxillary arch perimeter, mandibular arch perimeter, and palate height. The independent variables, besides age and sex, were a series of arc characteristics. The Student t test, paired Student t test, and Pearson correlation in SPSS version 19 were used for the analysis.Of the models, 60% were from women. Two of nine measurements for pre-treatment and 6 of 9 measurements for post-treatment showed a difference. The variables that were different between the manual and digital measurements in the pre-treatment were maxillary intermolar width and palate height (P < .05). Post-treatment, differences were found in mandibular intercanine width, palate height, overjet, overbite, and maxillary and mandibular arch perimeter (P < .05).The models measured manually and digitally showed certain similarities for both vertical and transverse measurements. There are many advantages offered to the orthodontist, such as easy storage; savings in time and space; facilitating the reproducibility of information; and conferring the security of not deteriorating over time. Its main disadvantage is the cost.

Effects of Word Width and Word Length on Optimal Character Size for Reading of Horizontally Scrolling Japanese Words

PubMed Central

Teramoto, Wataru; Nakazaki, Takuyuki; Sekiyama, Kaoru; Mori, Shuji

2016-01-01

The present study investigated, whether word width and length affect the optimal character size for reading of horizontally scrolling Japanese words, using reading speed as a measure. In Experiment 1, three Japanese words, each consisting of four Hiragana characters, sequentially scrolled on a display screen from right to left. Participants, all Japanese native speakers, were instructed to read the words aloud as accurately as possible, irrespective of their order within the sequence. To quantitatively measure their reading performance, we used rapid serial visual presentation paradigm, where the scrolling rate was increased until the participants began to make mistakes. Thus, the highest scrolling rate at which the participants’ performance exceeded 88.9% correct rate was calculated for each character size (0.3°, 0.6°, 1.0°, and 3.0°) and scroll window size (5 or 10 character spaces). Results showed that the reading performance was highest in the range of 0.6° to 1.0°, irrespective of the scroll window size. Experiment 2 investigated whether the optimal character size observed in Experiment 1 was applicable for any word width and word length (i.e., the number of characters in a word). Results showed that reading speeds were slower for longer than shorter words and the word width of 3.6° was optimal among the word lengths tested (three, four, and six character words). Considering that character size varied depending on word width and word length in the present study, this means that the optimal character size can be changed by word width and word length in scrolling Japanese words. PMID:26909052

Effects of Word Width and Word Length on Optimal Character Size for Reading of Horizontally Scrolling Japanese Words.

PubMed

Teramoto, Wataru; Nakazaki, Takuyuki; Sekiyama, Kaoru; Mori, Shuji

2016-01-01

The present study investigated, whether word width and length affect the optimal character size for reading of horizontally scrolling Japanese words, using reading speed as a measure. In Experiment 1, three Japanese words, each consisting of four Hiragana characters, sequentially scrolled on a display screen from right to left. Participants, all Japanese native speakers, were instructed to read the words aloud as accurately as possible, irrespective of their order within the sequence. To quantitatively measure their reading performance, we used rapid serial visual presentation paradigm, where the scrolling rate was increased until the participants began to make mistakes. Thus, the highest scrolling rate at which the participants' performance exceeded 88.9% correct rate was calculated for each character size (0.3°, 0.6°, 1.0°, and 3.0°) and scroll window size (5 or 10 character spaces). Results showed that the reading performance was highest in the range of 0.6° to 1.0°, irrespective of the scroll window size. Experiment 2 investigated whether the optimal character size observed in Experiment 1 was applicable for any word width and word length (i.e., the number of characters in a word). Results showed that reading speeds were slower for longer than shorter words and the word width of 3.6° was optimal among the word lengths tested (three, four, and six character words). Considering that character size varied depending on word width and word length in the present study, this means that the optimal character size can be changed by word width and word length in scrolling Japanese words.

Sensory substitution information informs locomotor adjustments when walking through apertures.

PubMed

Kolarik, Andrew J; Timmis, Matthew A; Cirstea, Silvia; Pardhan, Shahina

2014-03-01

The study assessed the ability of the central nervous system (CNS) to use echoic information from sensory substitution devices (SSDs) to rotate the shoulders and safely pass through apertures of different width. Ten visually normal participants performed this task with full vision, or blindfolded using an SSD to obtain information regarding the width of an aperture created by two parallel panels. Two SSDs were tested. Participants passed through apertures of +0, +18, +35 and +70 % of measured body width. Kinematic indices recorded movement time, shoulder rotation, average walking velocity across the trial, peak walking velocities before crossing, after crossing and throughout a whole trial. Analyses showed participants used SSD information to regulate shoulder rotation, with greater rotation associated with narrower apertures. Rotations made using an SSD were greater compared to vision, movement times were longer, average walking velocity lower and peak velocities before crossing, after crossing and throughout the whole trial were smaller, suggesting greater caution. Collisions sometimes occurred using an SSD but not using vision, indicating that substituted information did not always result in accurate shoulder rotation judgements. No differences were found between the two SSDs. The data suggest that spatial information, provided by sensory substitution, allows the relative position of aperture panels to be internally represented, enabling the CNS to modify shoulder rotation according to aperture width. Increased buffer space indicated by greater rotations (up to approximately 35 % for apertures of +18 % of body width) suggests that spatial representations are not as accurate as offered by full vision.

CLARREO Pathfinder Mission to ISS: Demonstrating Greatly Increased Accuracy for Reflected Solar Space Based Observations: Calibration and Intercalibration

NASA Astrophysics Data System (ADS)

Wielicki, B. A.

2016-12-01

The CLARREO (Climate Absolute Radiance and Refractivity) Pathfinder mission is a new mission started by NASA in 2016. CLARREO Pathfinder will fly a new generation of high accuracy reflected solar spectrometer in orbit on the Inernational Space Station (ISS) to demonstrate the ability to increase accuracy of reflected solar observations from space by a factor of 3 to 20. The spectrometer will use the sun and moon as calibration sources with a baseline objective of 0.3% (1 sigma) reflectance calibration uncertainty for the contiguous spectrum from 350nm to 2300nm, covering over 95% of the Earth's reflected solar spectrum. Spectral sampling is 3nm with resolution of 6nm. The spectrometer is mounted on a 2-axis gimbal enabling a new ability to use the same optical path to view the sun, moon, and Earth. Planned launch is 2020 with at least 1 year on orbit to demonstrate the new capability. The mission will also demonstrate the ability to use the new spectrometer as a reference transfer spectrometer in orbit to achieve intercalibration of reflected solar instruments to within 0.3% (1 sigma) using space, time, spectral, and angle matched observations across the full scan width of remote sensing instruments. Intercalibration to 0.3% will be demonstrated across the full scan width of the NASA CERES broadband radiometer and the NOAA VIIRS imager reflected solar spectral channels. This mission will demonstrate reflected solar intercalibration across the full swath width as opposed to current nadir only intercalibration used by GSICS (Global Space Based InterCalibration System). Intercalibration will include a new capability to determine scan angle dependence of polarization sensitivity of instruments like VIIRS. The high accuracy goals of this mission are driven primarily by the accuracy required to more rapidly and accurately observe climate change signals such as cloud feedback (see Wielicki et al. 2013 Bulletin of the American Meteorological Society). The new high accuracy and intercalibration capability will also be very useful for serving as a reference calibrator for constellations of operational instruments in Geostationary or Low Earth Orbit (e.g. land resource imagers, ocean color, cloud imagers). The higher accuracy will enable operational sensors to more effectively serve as climate change sensors.

Radiographic assessment of lower third molar eruption in different anteroposterior skeletal patterns and age-related groups.

PubMed

Jakovljevic, Aleksandar; Lazic, Emira; Soldatovic, Ivan; Nedeljkovic, Nenad; Andric, Miroslav

2015-07-01

To analyze radiographic predictors for lower third molar eruption among subjects with different anteroposterior skeletal relations and of different age groups. In total, 300 lower third molars were recorded on diagnostic digital orthopantomograms (DPTs) and lateral cephalograms (LCs). The radiographs were grouped according to sagittal intermaxillary angle (ANB), subject age, and level of lower third molar eruption. The DPT was used to analyze retromolar space, mesiodistal crown width, space/width ratio, third and second molar angulation (α, γ), third molar inclination (β), and gonion angle. The LC was used to determine ANB, angles of maxillar and mandibular prognathism (SNA, SNB), mandibular plane angle (SN/MP), and mandibular lengths. A logistic regression model was created using the statistically significant predictors. The logistic regression analysis revealed a statistically significant impact of β angle and distance between gonion and gnathion (Go-Gn) on the level of lower third molar eruption (P < .001 and P < .015, respectively). The retromolar space was significantly increased in the adult subgroup for all skeletal classes. The lower third molar impaction rate was significantly higher in the adult subgroup with the Class II (62.3%) compared with Class III subjects (31.7%; P < .013). The most favorable values of linear and angular predictors of mandibular third molar eruption were measured in Class III subjects. For valid estimation of mandibular third molar eruption, certain linear and angular measures (β angle, Go-Gn), as well as the size of the retromolar space, need to be considered.

The definition of the V zone for the safety space of functional surgery of the tongue.

PubMed

Hou, Tiening; Shao, Jinyan; Fang, Songhua

2012-01-01

To define safety space for functional surgery of the tongue. Prospective nonrandomized study. Computed tomographic angiography of the lingual artery was performed in 107 in-patients with obstructive sleep apnea syndrome and 17 controls. The safety space was ascertained according to the course of lingual artery. The course of the lingual artery, termed the Big Dipper bowl of the tongue, was similar in each group. The tissue above the lingual artery and the vacuity of the hypoglossal/lingual artery neurovascular bundle (HLNVB) formed a three-dimensional structure. The anterior part was named the V prozone. Its anterior border was the tangent plane of the deep lingual artery, its posterior border the circumvallate papilla, its width the interval of bilateral margins at the corresponding parts of the tongue, and its height the level of the middle lingual frenulum. The posterior portion between the bilateral dorsal arteries in the tongue base was named the V postzone. Its width was 31.42±3.82 mm when the tongue was in a resting position, and its height was the distance from the foramen cecum to the bottom of the epiglottic vallecula. The inferior part under the intrinsic lingual muscles was named the hypoglossal floor. It is a relatively restricted surgery zone. The V zone of the tongue without HLNVB travelling provides enough of safety space for functional surgery on the tongue. Copyright © 2011 The American Laryngological, Rhinological, and Otological Society, Inc.

High Voltage Solar Concentrator Experiment with Implications for Future Space Missions

NASA Technical Reports Server (NTRS)

Mehdi, Ishaque S.; George, Patrick J.; O'Neill, Mark; Matson, Robert; Brockschmidt, Arthur

2004-01-01

This paper describes the design, development, fabrication, and test of a high performance, high voltage solar concentrator array. This assembly is believed to be the first ever terrestrial triple-junction-cell solar array rated at over 1 kW. The concentrator provides over 200 W/square meter power output at a nominal 600 Vdc while operating under terrestrial sunlight. Space-quality materials and fabrication techniques were used for the array, and the 3005 meter elevation installation below the Tropic of Cancer allowed testing as close as possible to space deployment without an actual launch. The array includes two concentrator modules, each with a 3 square meter aperture area. Each concentrator module uses a linear Fresnel lens to focus sunlight onto a photovoltaic receiver that uses 240 series-connected triple-junction solar cells. Operation of the two receivers in series can provide 1200 Vdc which would be adequate for the 'direct drive' of some ion engines or microwave transmitters in space. Lens aperture width is 84 cm and the cell active width is 3.2 cm, corresponding to a geometric concentration ratio of 26X. The evaluation includes the concentrator modules, the solar cells, and the materials and techniques used to attach the solar cells to the receiver heat sink. For terrestrial applications, a finned aluminum extrusion was used for the heat sink for the solar cells, maintaining a low cell temperature so that solar cell efficiency remains high.

Impaired positioning of the gape in whiplash-associated disorders.

PubMed

Zafar, Hamayun; Nordh, Erik; Eriksson, Per-Olof

2006-01-01

We have previously introduced a new concept for natural jaw function suggesting that "functional jaw movements" are the result of coordinated jaw and neck muscle activation, leading to simultaneous movements in the temporomandibular, atlanto-occipital and cervical spine joints. Thus, jaw function requires a healthy state of both the jaw and the neck motor systems. The aim of this study was to examine the positioning of the gape in space during maximal jaw opening at fast and slow speed in healthy as well as whiplash-associated disorders (WAD) individuals. A wireless optoelectronic technique for three-dimensional movement recording was used. Subjects were seated in an upright position, with back support up to the mid-scapular level without headrest. The position of the gape in space was defined as the vertical midpoint position of the gape at maximal jaw opening (MP). In healthy, the MP generally coincided with the reference position at the start of jaw opening. In the WAD group, the MP was significantly lower than the reference position. No sex or speed related differences were found. The results suggest that both the width and orientation of the gape in space relies on coordinated jaw and neck muscle activation and mandibular and head-neck movements. This study also suggests an association between neck pain and dysfunction following trauma, and reduced width and impaired positioning of the gape in space. Finally, the MP seems to be a useful marker in evaluation of the functional state of the jaw-neck motor system.

Motor/Generator and Inverter Characterization for Flywheel System Applications

NASA Technical Reports Server (NTRS)

Tamarcus, Jeffries L.

2004-01-01

The Advanced Electrical Systems Development Branch at NASA Glenn Research Center (GRC) has been involved in the research and development of high speed flywheels systems for satellite energy storage and attitude applications. These flywheels will serve as replacement for chemical nickel hydrogen, nickel cadmium batteries and gyroscopic wheels. The advantages of using flywheel systems for energy storage on satellites are high energy density, high power density, long life, deep depth of discharge, and broad operating temperature ranges. A flywheel system for space applications consist of a number of flywheel modules, the motor/generator and magnetic bearing, and an electronics package. The motor/generator electronics package includes a pulse-width modulated inverter that drives the flywheel permanent magnet motor/generator located at one end of the shaft. This summer, I worked under the direct supervision of my mentor, Walter Santiago, and the goal for this summer was to characterize motor generator and inverter attributes in order to increase their viability as a more efficient energy storage source for space applications. To achieve this goal, magnetic field measurements around the motor/generator permanent magnet and the impedance of the motor/generator three phase windings were characterized, and a recreation of the inverter pulse width modulated control system was constructed. The Flywheel modules for space use are designed to maximize energy density and minimize loss, and attaining these values will aid in locating and reducing losses within the flywheel system as a whole, making flywheel technology more attractive for use as energy storage in future space applications.

Improving the machinability of leaded free cutting steel through process optimization

NASA Astrophysics Data System (ADS)

Sathyamurthy, P.; Vetrivelmurugan, R.; Sooryaprakash, J.

2018-02-01

Free cutting steel grades are high sulphur grades which can be classified under two categories as Leaded and Non-Leaded. These grades are used for manufacturing components like Nuts, bolts, studs, hydraulic fittings, brake pistons where higher machining is required to get intricate shape. Machinability of these grades are affected by hard oxide inclusions and highly deformed manganese sulphide inclusions. At JSW, machinability of leaded free cutting steel is improved by various process modifications namely deoxidation through carbon and manganese, Tellurium (Rare earth element) addition and maintaining the oxygen level at 80- 120ppm. Former one avoids the formation of hard SiO2 and Al2O3 compounds, Tellurium addition forms PbTe compound at the tail of MnS inclusions which resists the deformation of MnS inclusions and increased oxygen level favours the formation of less deformable oxy- sulphide inclusions. Above process modifications have resulted in achieving the low silicate content, better aspect ratio of MnS inclusions in the final rolled product. They are assessed by the characteristics of chip formation and surface roughness of machined part.

The decay width of stringy hadrons

NASA Astrophysics Data System (ADS)

Sonnenschein, Jacob; Weissman, Dorin

2018-02-01

In this paper we further develop a string model of hadrons by computing their strong decay widths and comparing them to experiment. The main decay mechanism is that of a string splitting into two strings. The corresponding total decay width behaves as Γ = π/2 ATL where T and L are the tension and length of the string and A is a dimensionless universal constant. We show that this result holds for a bosonic string not only in the critical dimension. The partial width of a given decay mode is given by Γi / Γ =Φi exp ⁡ (- 2 πCmsep2 / T) where Φi is a phase space factor, msep is the mass of the "quark" and "antiquark" created at the splitting point, and C is a dimensionless coefficient close to unity. Based on the spectra of hadrons we observe that their (modified) Regge trajectories are characterized by a negative intercept. This implies a repulsive Casimir force that gives the string a "zero point length". We fit the theoretical decay width to experimental data for mesons on the trajectories of ρ, ω, π, η, K*, ϕ, D, and Ds*, and of the baryons N, Δ, Λ, and Σ. We examine both the linearity in L and the exponential suppression factor. The linearity was found to agree with the data well for mesons but less for baryons. The extracted coefficient for mesons A = 0.095 ± 0.015 is indeed quite universal. The exponential suppression was applied to both strong and radiative decays. We discuss the relation with string fragmentation and jet formation. We extract the quark-diquark structure of baryons from their decays. A stringy mechanism for Zweig suppressed decays of quarkonia is proposed and is shown to reproduce the decay width of ϒ states. The dependence of the width on spin and flavor symmetry is discussed. We further apply this model to the decays of glueballs and exotic hadrons.

24 CFR 3280.111 - Toilet compartments.

Code of Federal Regulations, 2012 CFR

2012-04-01

... line of the toilet shall not be less than 12 inches. At least 21 inches of clear space shall be... 24 Housing and Urban Development 5 2012-04-01 2012-04-01 false Toilet compartments. 3280.111... Toilet compartments. Each toilet compartment shall be a minimum of 30 inches in width, except, when the...

24 CFR 3280.111 - Toilet compartments.

Code of Federal Regulations, 2010 CFR

2010-04-01

... line of the toilet shall not be less than 12 inches. At least 21 inches of clear space shall be... 24 Housing and Urban Development 5 2010-04-01 2010-04-01 false Toilet compartments. 3280.111... Toilet compartments. Each toilet compartment shall be a minimum of 30 inches in width, except, when the...

24 CFR 3280.111 - Toilet compartments.

Code of Federal Regulations, 2013 CFR

2013-04-01

... line of the toilet shall not be less than 12 inches. At least 21 inches of clear space shall be... 24 Housing and Urban Development 5 2013-04-01 2013-04-01 false Toilet compartments. 3280.111... Toilet compartments. Each toilet compartment shall be a minimum of 30 inches in width, except, when the...

24 CFR 3280.111 - Toilet compartments.

Code of Federal Regulations, 2011 CFR

2011-04-01

... line of the toilet shall not be less than 12 inches. At least 21 inches of clear space shall be... 24 Housing and Urban Development 5 2011-04-01 2011-04-01 false Toilet compartments. 3280.111... Toilet compartments. Each toilet compartment shall be a minimum of 30 inches in width, except, when the...

Self-focusing and group-velocity dispersion of pulsed laser beams in the inhomogeneous atmosphere.

PubMed

Zhang, Yuqiu; Ji, Xiaoling; Zhang, Hao; Li, Xiaoqing; Wang, Tao; Wang, Huan; Deng, Yu

2018-05-28

We study self-focusing and group-velocity dispersion (GVD) effects in the inhomogeneous atmosphere on pulsed-laser space debris removal facilitated by a ground-based laser. It is found that changes of the pulse duration and the beam spot size with the propagation distance are noticeable due to the interplay of the GVD effect and the self-focusing effect, which is quite different from the behavior in the linear case. It is shown that the temporal pulse splitting may appear on the space debris, and the spatial side lobe usually appears together with the temporal pulse splitting. As compared with the linear case, the beam width and the pulse width on the debris target increase. On the other hand, crucial formulae of the modified focal length and the M 2 -factor for laser debris removal are also derived. It is found that the beam quality on the debris target becomes better if our modified focal length is adopted, and the beam quality on the debris target will be good if the value of M 2 -factor is less than 1.6.

Space Plasma Ion Processing of the Lunar Soil: Modeling of Radiation-Damaged Rim Widths on Lunar Grains

NASA Technical Reports Server (NTRS)

Chamberlin, S.; Christoffersen, R.; Keller, L.

2007-01-01

Chemically and microstructurally complex altered rims around grains in the finest size fraction (<20 micron) of the lunar regolith are the result of multi-stage processes involving both solar ion radiation damage and nanoscale deposition of impact or sputter-derived vapors. The formation of the rims is an important part of the space weathering process, and is closely linked to key changes in optical reflectance and other bulk properties of the lunar surface. Recent application of field-emission scanning transmission electron microscope techniques, including energy dispersive X-ray spectral imaging, is making it easier to unravel the "nano-stratigraphy" of grain rims, and to delineate the portions of rims that represent Radiation-Amorphized (RA) host grain from overlying amorphous material that represents vapor/sputter deposits. For the portion of rims formed by host grain amorphization (henceforth called RA rims), we have been investigating the feasibility of using Monte Carlo-type ion-atom collision models, combined with experimental ion irradiation data, to derive predictive numerical models linking the width of RA rims to the grain s integrated solar ion radiation exposure time.

An assessment of buffer strips for improving damage tolerance

NASA Technical Reports Server (NTRS)

Poe, C. C., Jr.; Kennedy, J. M.

1981-01-01

Graphite/epoxy panels with buffer strips were tested in tension to measure their residual strength with crack-like damage. Panels were made with 45/0/-45/90(2S) and 45/0/450(2S) layups. The buffer strips were parallel to the loading directions. They were made by replacing narrow strips of the 0 deg graphite plies with strips of either 0 deg S-Glass/epoxy or Kevlar-49/epoxy on either a one for one or a two for one basis. In a third case, O deg graphite/epoxy was used as the buffer material and thin, perforated Mylar strips were placed between the 0 deg piles and the cross-plies to weaken the interfaces and thus to isolate the 0 deg plies. Some panels were made with buffer strips of different widths and spacings. The buffer strips arrested the cracks and increased the residual strengths significantly over those plain laminates without buffer strips. A shear-lag type stress analysis correctly predicted the effects of layups, buffer material, buffer strip width and spacing, and the number of plies of buffer material.

An assessment of buffer strips for improving damage tolerance of composite laminates

NASA Technical Reports Server (NTRS)

Poe, C. C., Jr.; Kennedy, J. M.

1980-01-01

Graphite/epoxy panels with buffer strips were tested in tension to measure their residual strength with crack-like damage. Panels were made with (45/0/-45/90)2S and (45/0/-45/0)2S layups. The buffer strips were parallel to the loading direction. They were made by replacing narrow strips of the 0 deg graphite plies with strips of either 0 deg S-Glass/epoxy or Kevlar-90/epoxy on either a one-for-one or a two-for-one basis. In a third case, 0 deg graphite/epoxy was used as the buffer material and thin, perforated Mylar strips were placed between the 0 deg plies and the cross-plies to weaken the interfaces and thus to isolate the 0 deg plies. Some panels were made with buffer strips of different width and spacings. The buffer strips arrested the cracks and increased the residual strengths significantly over those of plain laminates without buffer strips. A shear-lag type stress analysis correctly predicted the effects of layup, buffer material, buffer strip width and spacing, and the number of plies of buffer material

Reciprocal-space mapping of epitaxic thin films with crystallite size and shape polydispersity.

PubMed

Boulle, A; Conchon, F; Guinebretière, R

2006-01-01

A development is presented that allows the simulation of reciprocal-space maps (RSMs) of epitaxic thin films exhibiting fluctuations in the size and shape of the crystalline domains over which diffraction is coherent (crystallites). Three different crystallite shapes are studied, namely parallelepipeds, trigonal prisms and hexagonal prisms. For each shape, two cases are considered. Firstly, the overall size is allowed to vary but with a fixed thickness/width ratio. Secondly, the thickness and width are allowed to vary independently. The calculations are performed assuming three different size probability density functions: the normal distribution, the lognormal distribution and a general histogram distribution. In all cases considered, the computation of the RSM only requires a two-dimensional Fourier integral and the integrand has a simple analytical expression, i.e. there is no significant increase in computing times by taking size and shape fluctuations into account. The approach presented is compatible with most lattice disorder models (dislocations, inclusions, mosaicity, ...) and allows a straightforward account of the instrumental resolution. The applicability of the model is illustrated with the case of an yttria-stabilized zirconia film grown on sapphire.

Neutronic reactor thermal shield

DOEpatents

Lowe, Paul E.

1976-06-15

1. The combination with a plurality of parallel horizontal members arranged in horizontal and vertical rows, the spacing of the members in all horizontal rows being equal throughout, the spacing of the members in all vertical rows being equal throughout; of a shield for a nuclear reactor comprising two layers of rectangular blocks through which the members pass generally perpendicularly to the layers, each block in each layer having for one of the members an opening equally spaced from vertical sides of the block and located closer to the top of the block than the bottom thereof, whereby gravity tends to make each block rotate about the associated member to a position in which the vertical sides of the block are truly vertical, the openings in all the blocks of one layer having one equal spacing from the tops of the blocks, the openings in all the blocks of the other layer having one equal spacing from the tops of the blocks, which spacing is different from the corresponding spacing in the said one layer, all the blocks of both layers having the same vertical dimension or length, the blocks of both layers consisting of relatively wide blocks and relatively narrow blocks, all the narrow blocks having the same horizontal dimension or width which is less than the horizontal dimension or width of the wide blocks, which is the same throughout, each layer consisting of vertical rows of narrow blocks and wide blocks alternating with one another, each vertical row of narrow blocks of each layer being covered by a vertical row of wide blocks of the other layer which wide blocks receive the same vertical row of members as the said each vertical row of narrow blocks, whereby the rectangular perimeters of each block of each layer is completely out of register with that of each block in the other layer.

Longitudinal Changes of Angle Configuration in Primary Angle-Closure Suspects

PubMed Central

Jiang, Yuzhen; Chang, Dolly S.; Zhu, Haogang; Khawaja, Anthony P.; Aung, Tin; Huang, Shengsong; Chen, Qianyun; Munoz, Beatriz; Grossi, Carlota M.

2015-01-01

Objective To determine longitudinal changes in angle configuration in the eyes of primary angle-closure suspects (PACS) treated by laser peripheral iridotomy (LPI) and in untreated fellow eyes. Design Longitudinal cohort study. Participants Primary angle-closure suspects aged 50 to 70 years were enrolled in a randomized, controlled clinical trial. Methods Each participant was treated by LPI in 1 randomly selected eye, with the fellow eye serving as a control. Angle width was assessed in a masked fashion using gonioscopy and anterior segment optical coherence tomography (AS-OCT) before and at 2 weeks, 6 months, and 18 months after LPI. Main Outcome Measures Angle width in degrees was calculated from Shaffer grades assessed under static gonioscopy. Angle configuration was also evaluated using angle opening distance (AOD250, AOD500, AOD750), trabecular-iris space area (TISA500, TISA750), and angle recess area (ARA) measured in AS-OCT images. Results No significant difference was found in baseline measures of angle configuration between treated and untreated eyes. At 2 weeks after LPI, the drainage angle on gonioscopy widened from a mean of 13.5° at baseline to a mean of 25.7° in treated eyes, which was also confirmed by significant increases in all AS-OCT angle width measures (P<0.001 for all variables). Between 2 weeks and 18 months after LPI, a significant decrease in angle width was observed over time in treated eyes (P<0.001 for all variables), although the change over the first 5.5 months was not statistically significant for angle width measured under gonioscopy (P = 0.18), AOD250 (P = 0.167) and ARA (P = 0.83). In untreated eyes, angle width consistently decreased across all follow-up visits after LPI, with a more rapid longitudinal decrease compared with treated eyes (P values for all variables ≤0.003). The annual rate of change in angle width was equivalent to 1.2°/year (95% confidence interval [CI], 0.8–1.6) in treated eyes and 1.6°/year (95% CI, 1.3–2.0) in untreated eyes (P<0.001). Conclusions Angle width of treated eyes increased markedly after LPI, remained stable for 6 months, and then decreased significantly by 18 months after LPI. Untreated eyes experienced a more consistent and rapid decrease in angle width over the same time period. PMID:24835757

GPS Space Service Volume: Ensuring Consistent Utility Across GPS Design Builds for Space Users

NASA Technical Reports Server (NTRS)

Bauer, Frank H.; Parker, Joel Jefferson Konkl; Valdez, Jennifer Ellen

2015-01-01

GPS availability and signal strength originally specified for users on or near surface of Earth with transmitted power levels specified at edge-of-Earth, 14.3 degrees. Prior to the SSV specification, on-orbit performance of GPS varied from block build to block build (IIA, IIRM, IIF) due to antenna gain and beam width variances. Unstable on-orbit performance results in significant risk to space users. Side-lobe signals, although not specified, were expected to significantly boost GPS signal availability for users above the constellation. During GPS III Phase A, NASA noted significant discrepancies in power levels specified in GPS III specification documents, and measured on-orbit performance. To stabilize the signal for high altitude space users, NASA DoD team in 2003-2005 led the creation of new Space Service Volume (SSV) definition and specifications.

Direct measurement of exciton dissociation energy in polymers

NASA Astrophysics Data System (ADS)

Toušek, J.; Toušková, J.; Chomutová, R.; Paruzel, B.; Pfleger, J.

2017-01-01

Exciton dissociation energy was obtained based on the comparison of thickness of the space charge region estimated from the measurement of capacitance of prepared Schottky diode and from the measurement of photovoltage spectra. While the capacitance measurements provide information about the total width of the space charge region (SCR) the surface photovoltaic effect brings information only about the part of the SCR where electric field is sufficiently high to cause dissociation. For determination of the dissociation energy it is sufficient to find the electric potential in the SCR where the process starts.

Joint optimization of a partially coherent Gaussian beam for free-space optical communication over turbulent channels with pointing errors.

PubMed

Lee, It Ee; Ghassemlooy, Zabih; Ng, Wai Pang; Khalighi, Mohammad-Ali

2013-02-01

Joint beam width and spatial coherence length optimization is proposed to maximize the average capacity in partially coherent free-space optical links, under the combined effects of atmospheric turbulence and pointing errors. An optimization metric is introduced to enable feasible translation of the joint optimal transmitter beam parameters into an analogous level of divergence of the received optical beam. Results show that near-ideal average capacity is best achieved through the introduction of a larger receiver aperture and the joint optimization technique.

Long wavelength infrared detector

NASA Technical Reports Server (NTRS)

Vasquez, Richard P. (Inventor)

1993-01-01

Long wavelength infrared detection is achieved by a detector made with layers of quantum well material bounded on each side by barrier material to form paired quantum wells, each quantum well having a single energy level. The width and depth of the paired quantum wells, and the spacing therebetween, are selected to split the single energy level with an upper energy level near the top of the energy wells. The spacing is selected for splitting the single energy level into two energy levels with a difference between levels sufficiently small for detection of infrared radiation of a desired wavelength.

Investigation of a Space Delta Technology Facility (SDTF) for Spacelab

NASA Technical Reports Server (NTRS)

Welch, J. D.

1977-01-01

The Space Data Technology Facility (SDTF) would have the role of supporting a wide range of data technology related demonstrations which might be performed on Spacelab. The SDTF design is incorporated primarily in one single width standardized Spacelab rack. It consists of various display, control and data handling components together with interfaces with the demonstration-specific equipment and Spacelab. To arrive at this design a wide range of data related technologies and potential demonstrations were also investigated. One demonstration concerned with online image rectification and registration was developed in some depth.

Doping dependence of the contact resistivity of end-bonded metal contacts to thin heavily doped semiconductor nanowires

NASA Astrophysics Data System (ADS)

Shukkoor, Anvar A.; Karmalkar, Shreepad

2017-12-01

We study the resistivity, ρcN, of end-bonded contacts to semiconductor NanoWires (NWs) of radius R = 5-10 nm over doping Nd = 1018-1020 cm-3. The study is important for NW device design and characterization. It reports realistic calculations of ρcN and highlights and explains how ρcN differs significantly from the resistivity ρcB of bulk contacts. First, the space-charge width in NW contacts is increased by the surrounding field which depends on R, contact geometry, and ambient dielectric; this width also depends on surface charge and dielectric confinement which reduces dopant ionization. Second, thin NWs have a low effective lifetime, τN, due to surface recombination. Third, NW contacts have a lesser image force barrier lowering due to the higher space-charge width. Due to these factors, apart from tunneling (which decides ρcB), space-charge region generation-recombination current also affects ρcN. As Nd is raised from 1018 to 1020 cm-3, ρcB falls rapidly, but ρcN varies slowly and may even increase up to 3-5 × 1018 and then falls rapidly. Further, ρcN/ρcB can be ≪1 at Nd = 1 × 1018 cm-3, reaches a peak ≫1 around Nd = 1 × 1019 cm-3, and → 1 at Nd = 1 × 1020 cm-3, e.g., for 0.8 V contact barrier on 10 nm thick n-type silicon NWs with τN = 1 ps embedded in SiO2, at T = 300 K, even a 10 nm contact extension yields a peak of 75 at Nd = 8 × 1018 cm-3. We study changes in ρcN/ρcB versus Nd behavior with R, contact geometry, ambient dielectric, surface charge, τN, T, tunneling mass, and barrier height.

Characterization of process-induced damage in Cu/low-k interconnect structure by microscopic infrared spectroscopy with polarized infrared light

DOE Office of Scientific and Technical Information (OSTI.GOV)

Seki, Hirofumi, E-mail: Hirofumi-Seki@trc.toray.co.jp; Hashimoto, Hideki; Ozaki, Yukihiro

Microscopic Fourier-transform infrared (FT-IR) spectra are measured for a Cu/low-k interconnect structure using polarized IR light for different widths of low-k spaces and Cu lines, and for different heights of Cu lines, on Si substrates. Although the widths of the Cu line and the low-k space are 70 nm each, considerably smaller than the wavelength of the IR light, the FT-IR spectra of the low-k film were obtained for the Cu/low-k interconnect structure. A suitable method was established for measuring the process-induced damage in a low-k film that was not detected by the TEM-EELS (Transmission Electron Microscope-Electron Energy-Loss Spectroscopy) using microscopicmore » IR polarized light. Based on the IR results, it was presumed that the FT-IR spectra mainly reflect the structural changes in the sidewalls of the low-k films for Cu/low-k interconnect structures, and the mechanism of generating process-induced damage involves the generation of Si-OH groups in the low-k film when the Si-CH{sub 3} bonds break during the fabrication processes. The Si-OH groups attract moisture and the OH peak intensity increases. It was concluded that the increase in the OH groups in the low-k film is a sensitive indicator of low-k damage. We achieved the characterization of the process-induced damage that was not detected by the TEM-EELS and speculated that the proposed method is applicable to interconnects with line and space widths of 70 nm/70 nm and on shorter scales of leading edge devices. The location of process-induced damage and its mechanism for the Cu/low-k interconnect structure were revealed via the measurement method.« less

The influence of scoring targets and outer-floaters on attacking and defending team dispersion, shape and creation of space during small-sided soccer games.

PubMed

Castellano, Julen; Silva, Pedro; Usabiaga, Oidui; Barreira, Daniel

2016-06-01

The effect of altered game formats on team performances during soccer practice can be harnessed by coaches to stimulate specific tactical behaviours. The aim of the present study was to analyse the influence of using (i) small goals [SG], (ii) goalkeepers [7G] and (iii) floaters [7GF] on the dispersion, shape and available space of teams during small-sided games (SSGs). Twenty-four male soccer players were distributed into four teams composed of five players, two goalkeepers and two floaters that performed six SSG bouts of 6 min, interspersed with 6 min of passive recovery. Offensive and defensive phases were also analysed separately in order to verify the preservation of basic principles of attacking (teams more stretched to create free space) and defending (teams more compact to tie-up space) during SSGs. The variables used to characterize the collective behaviour were: length [L], width [W], team shape [Sh], and team separateness [TS]. Results revealed that the teams showed different collective behaviours depending on SSG format and a playing phase: a) L and W were higher in attack than in defence in all SSGs; b) team shapes were more elongated in defence in all SSGs except SG; c) the space separating players from their closest opponents (TS) was shorter in 7G; and d) SG and 7GF elicited greater defensive openness due to increased team width. The results suggest that manipulating task constraints, such as goal size, presence or absence of goalkeepers and floaters can be harnessed by coaches to shape distinct team tactical behaviours in SSGs while preserving the basic principles of attacking and defending.

The influence of scoring targets and outer-floaters on attacking and defending team dispersion, shape and creation of space during small-sided soccer games

PubMed Central

Silva, Pedro; Usabiaga, Oidui; Barreira, Daniel

2016-01-01

Abstract The effect of altered game formats on team performances during soccer practice can be harnessed by coaches to stimulate specific tactical behaviours. The aim of the present study was to analyse the influence of using (i) small goals [SG], (ii) goalkeepers [7G] and (iii) floaters [7GF] on the dispersion, shape and available space of teams during small-sided games (SSGs). Twenty-four male soccer players were distributed into four teams composed of five players, two goalkeepers and two floaters that performed six SSG bouts of 6 min, interspersed with 6 min of passive recovery. Offensive and defensive phases were also analysed separately in order to verify the preservation of basic principles of attacking (teams more stretched to create free space) and defending (teams more compact to tie-up space) during SSGs. The variables used to characterize the collective behaviour were: length [L], width [W], team shape [Sh], and team separateness [TS]. Results revealed that the teams showed different collective behaviours depending on SSG format and a playing phase: a) L and W were higher in attack than in defence in all SSGs; b) team shapes were more elongated in defence in all SSGs except SG; c) the space separating players from their closest opponents (TS) was shorter in 7G; and d) SG and 7GF elicited greater defensive openness due to increased team width. The results suggest that manipulating task constraints, such as goal size, presence or absence of goalkeepers and floaters can be harnessed by coaches to shape distinct team tactical behaviours in SSGs while preserving the basic principles of attacking and defending. PMID:28149378

[Anthropometry in workers and ergonomic aspects of work stations in the printing plant of the government of the state of Zulia, Venezuela].

PubMed

Rojas-González, L; Chacín-Almarza, B; Corzo-Alvarez, G; Sanabria-Vera, C; Nuñez-González, J

2000-12-01

To measure the corporal dimensions of the workers and the relationships with the spaces and equipments used in the printing processes, as the initial phase for the design and implementation of a surveillance program of work-related musculoskeletal disorders, 38 workers of a press were studied, by making an anthropometric record for ergonomic studies (CAPEE). The interior spaces and machinery were measured according to a format designed for that purpose. When the anthropometric parameters for each sex, the width elbow-elbow, height of the plane of the seat--elbow, height floor--upper face of the thigh and maximum width of hips were compared, they did not present significant differences. The other anthropometric parameters differ statistically (p < 0.05), being greater in men, except the height of the heel (p < 0.01). When relating the anthropometric measures and those of the interior spaces, there were no relationships among the maximum vertical reach of knuckles with the minimum height of objects and controls, the plane height of the seat-eye with the height of the computer's monitor and the sacrum-knee distance with the height of the work surface. The other variables showed a significant statistical relationship (p < 0.05). The interior spaces of the press are adapted to the anthropometric measures of its workers, fulfilling ergonomics approaches. These anthropometric measures and the ergonomics aspects of objects and workplace provide elements that will allow the design and the implementation of surveillance programs for the control and the prevention of work-related musculoskeletal disorders, related to the personnel's inadequate selection and to the redesign of interior spaces, and the selection of the machinery and tools to use in the technological processes.

Effect of H-wave polarization on laser radar detection of partially convex targets in random media.

PubMed

El-Ocla, Hosam

2010-07-01

A study on the performance of laser radar cross section (LRCS) of conducting targets with large sizes is investigated numerically in free space and random media. The LRCS is calculated using a boundary value method with beam wave incidence and H-wave polarization. Considered are those elements that contribute to the LRCS problem including random medium strength, target configuration, and beam width. The effect of the creeping waves, stimulated by H-polarization, on the LRCS behavior is manifested. Targets taking large sizes of up to five wavelengths are sufficiently larger than the beam width and are sufficient for considering fairly complex targets. Scatterers are assumed to have analytical partially convex contours with inflection points.

Self-organization of linear nanochannel networks

NASA Astrophysics Data System (ADS)

Annabattula, R. K.; Veenstra, J. M.; Mei, Y. F.; Schmidt, O. G.; Onck, P. R.

2010-06-01

A theoretical study has been conducted to explore the mechanics of self-organizing channel networks with dimensions in the submicron range and nanorange. The channels form by the partial release and bond back of prestressed thin films. In the release phase, the film spontaneously buckles into wrinkles of a certain wavelength, followed by a bond-back phase in which the final channel geometry is established through cohesive interface attractions. Results are presented in terms of the channel spacing, height, and width as a function of the film stiffness, thickness, eigenstrain, etch width, and interface energy. We have identified two dimensionless parameters that fully quantify the network assembly, showing excellent agreement with experiments. Our results provide valuable insight for the design of submicron and nanoscale channel networks with specific geometries.

Improving the theoretical prediction for the Bs - B̅s width difference: matrix elements of next-to-leading order ΔB = 2 operators

NASA Astrophysics Data System (ADS)

Davies, Christine; Harrison, Judd; Lepage, G. Peter; Monahan, Christopher; Shigemitsu, Junko; Wingate, Matthew

2018-03-01

We present lattice QCD results for the matrix elements of R2 and other dimension-7, ΔB = 2 operators relevant for calculations of Δs, the Bs - B̅s width difference. We have computed correlation functions using 5 ensembles of the MILC Collaboration's 2+1 + 1-flavour gauge field configurations, spanning 3 lattice spacings and light sea quarks masses down to the physical point. The HISQ action is used for the valence strange quarks, and the NRQCD action is used for the bottom quarks. Once our analysis is complete, the theoretical uncertainty in the Standard Model prediction for ΔΓs will be substantially reduced.

Quench-induced breathing mode of one-dimensional Bose gases.

PubMed

Fang, Bess; Carleo, Giuseppe; Johnson, Aisling; Bouchoule, Isabelle

2014-07-18

We measure the position- and momentum-space breathing dynamics of trapped one-dimensional Bose gases at finite temperature. The profile in real space reveals sinusoidal width oscillations whose frequency varies continuously through the quasicondensate to ideal Bose gas crossover. A comparison with theoretical models taking temperature into account is provided. In momentum space, we report the first observation of a frequency doubling in the quasicondensate regime, corresponding to a self-reflection mechanism due to the repulsive interactions. Such a mechanism is predicted for a fermionized system, and has not been observed to date. The disappearance of the frequency doubling through the crossover is mapped out experimentally, giving insights into the dynamics of the breathing evolution.

Quench-Induced Breathing Mode of One-Dimensional Bose Gases

NASA Astrophysics Data System (ADS)

Fang, Bess; Carleo, Giuseppe; Johnson, Aisling; Bouchoule, Isabelle

2014-07-01

We measure the position- and momentum-space breathing dynamics of trapped one-dimensional Bose gases at finite temperature. The profile in real space reveals sinusoidal width oscillations whose frequency varies continuously through the quasicondensate to ideal Bose gas crossover. A comparison with theoretical models taking temperature into account is provided. In momentum space, we report the first observation of a frequency doubling in the quasicondensate regime, corresponding to a self-reflection mechanism due to the repulsive interactions. Such a mechanism is predicted for a fermionized system, and has not been observed to date. The disappearance of the frequency doubling through the crossover is mapped out experimentally, giving insights into the dynamics of the breathing evolution.

Triangulation of multistation camera data to locate a curved line in space

NASA Technical Reports Server (NTRS)

Fricke, C. L.

1974-01-01

A method is described for finding the location of a curved line in space from local azimuth as a function of elevation data obtained at several observation sites. A least-squares criterion is used to insure the best fit to the data. The method is applicable to the triangulation of an object having no identifiable structural features, provided its width is very small compared with its length so as to approximate a line in space. The method was implemented with a digital computer program and was successfully applied to data obtained from photographs of a barium ion cloud which traced out the earth's magnetic field line at very high altitudes.

Shining a light on galactic outflows: photoionized outflows

NASA Astrophysics Data System (ADS)

Chisholm, John; Tremonti, Christy A.; Leitherer, Claus; Chen, Yanmei; Wofford, Aida

2016-04-01

We study the ionization structure of galactic outflows in 37 nearby, star-forming galaxies with the Cosmic Origins Spectrograph on the Hubble Space Telescope. We use the O I, Si II, Si III, and Si IV ultraviolet absorption lines to characterize the different ionization states of outflowing gas. We measure the equivalent widths, line widths, and outflow velocities of the four transitions, and find shallow scaling relations between them and galactic stellar mass and star formation rate. Regardless of the ionization potential, lines of similar strength have similar velocities and line widths, indicating that the four transitions can be modelled as a comoving phase. The Si equivalent width ratios (e.g. Si IV/Si II) have low dispersion, and little variation with stellar mass; while ratios with O I and Si vary by a factor of 2 for a given stellar mass. Photoionization models reproduce these equivalent width ratios, while shock models under predict the relative amount of high ionization gas. The photoionization models constrain the ionization parameter (U) between -2.25 < log (U) < -1.5, and require that the outflow metallicities are greater than 0.5 Z⊙. We derive ionization fractions for the transitions, and show that the range of ionization parameters and stellar metallicities leads to a factor of 1.15-10 variation in the ionization fractions. Historically, mass outflow rates are calculated by converting a column density measurement from a single metal ion into a total hydrogen column density using an ionization fraction, thus mass outflow rates are sensitive to the assumed ionization structure of the outflow.

Accuracy and Measurement Error of the Medial Clear Space of the Ankle.

PubMed

Metitiri, Ogheneochuko; Ghorbanhoseini, Mohammad; Zurakowski, David; Hochman, Mary G; Nazarian, Ara; Kwon, John Y

2017-04-01

Measurement of the medial clear space (MCS) is commonly used to assess deltoid ligament competency and mortise stability when managing ankle fractures. Lacking knowledge of the true anatomic width measured, previous studies have been unable to measure accuracy of measurement. The purpose of this study was to determine MCS measurement error and accuracy and any influencing factors. Using 3 normal transtibial ankle cadaver specimens, deltoid and syndesmotic ligaments were transected and the mortise widened and affixed at a width of 6 mm (specimen 1) and 4 mm (specimen 2). The mortise was left intact in specimen 3. Radiographs were obtained of each cadaver at varying degrees of rotation. Radiographs were randomized, and providers measured the MCS using a standardized technique. Lack of accuracy as well as lack of precision in measurement of the medial clear space compared to a known anatomic value was present for all 3 specimens tested. There were no significant differences in mean delta with regard to level of training for specimens 1 and 2; however, with specimen 3, staff physicians showed increased measurement accuracy compared with trainees. Accuracy and precision of MCS measurements are poor. Provider experience did not appear to influence accuracy and precision of measurements for the displaced mortise. This high degree of measurement error and lack of precision should be considered when deciding treatment options based on MCS measurements.

Fitted Hanbury-Brown Twiss radii versus space-time variances in flow-dominated models

NASA Astrophysics Data System (ADS)

Frodermann, Evan; Heinz, Ulrich; Lisa, Michael Annan

2006-04-01

The inability of otherwise successful dynamical models to reproduce the Hanbury-Brown Twiss (HBT) radii extracted from two-particle correlations measured at the Relativistic Heavy Ion Collider (RHIC) is known as the RHIC HBT Puzzle. Most comparisons between models and experiment exploit the fact that for Gaussian sources the HBT radii agree with certain combinations of the space-time widths of the source that can be directly computed from the emission function without having to evaluate, at significant expense, the two-particle correlation function. We here study the validity of this approach for realistic emission function models, some of which exhibit significant deviations from simple Gaussian behavior. By Fourier transforming the emission function, we compute the two-particle correlation function, and fit it with a Gaussian to partially mimic the procedure used for measured correlation functions. We describe a novel algorithm to perform this Gaussian fit analytically. We find that for realistic hydrodynamic models the HBT radii extracted from this procedure agree better with the data than the values previously extracted from the space-time widths of the emission function. Although serious discrepancies between the calculated and the measured HBT radii remain, we show that a more apples-to-apples comparison of models with data can play an important role in any eventually successful theoretical description of RHIC HBT data.

Fitted Hanbury-Brown-Twiss radii versus space-time variances in flow-dominated models

DOE Office of Scientific and Technical Information (OSTI.GOV)

Frodermann, Evan; Heinz, Ulrich; Lisa, Michael Annan

2006-04-15

The inability of otherwise successful dynamical models to reproduce the Hanbury-Brown-Twiss (HBT) radii extracted from two-particle correlations measured at the Relativistic Heavy Ion Collider (RHIC) is known as the RHIC HBT Puzzle. Most comparisons between models and experiment exploit the fact that for Gaussian sources the HBT radii agree with certain combinations of the space-time widths of the source that can be directly computed from the emission function without having to evaluate, at significant expense, the two-particle correlation function. We here study the validity of this approach for realistic emission function models, some of which exhibit significant deviations from simplemore » Gaussian behavior. By Fourier transforming the emission function, we compute the two-particle correlation function, and fit it with a Gaussian to partially mimic the procedure used for measured correlation functions. We describe a novel algorithm to perform this Gaussian fit analytically. We find that for realistic hydrodynamic models the HBT radii extracted from this procedure agree better with the data than the values previously extracted from the space-time widths of the emission function. Although serious discrepancies between the calculated and the measured HBT radii remain, we show that a more apples-to-apples comparison of models with data can play an important role in any eventually successful theoretical description of RHIC HBT data.« less

30 CFR 75.206 - Conventional roof support.

Code of Federal Regulations, 2010 CFR

2010-07-01

... materials are used as the only means of support— (1) The width of any opening shall not exceed 20 feet; (2) The spacing of roadway roof support shall not exceed 5 feet; (3)(i) Supports shall be installed to within 5 feet of the uncut face; (ii) When supports nearest the face must be removed to facilitate the...

30 CFR 75.206 - Conventional roof support.

Code of Federal Regulations, 2011 CFR

2011-07-01

... materials are used as the only means of support— (1) The width of any opening shall not exceed 20 feet; (2) The spacing of roadway roof support shall not exceed 5 feet; (3)(i) Supports shall be installed to within 5 feet of the uncut face; (ii) When supports nearest the face must be removed to facilitate the...

Estimation of pedestrian level UV exposure under trees

Treesearch

Richard H. Grant; Gordon M. Heisler; Wei Gao

2002-01-01

Trees influence the amount of solar UV radiation that reaches pedestrians. A three-dimensional model was developed to predict the ultraviolet-B (UV-B) irradiance fields in open-tree canopies where the spacing between trees is equal to or greater than the width of individual tree crowns. The model predicted the relative irradiance (fraction of above-canopy irradiance)...

16 CFR 309.20 - Labeling requirements for new covered vehicles.

Code of Federal Regulations, 2010 CFR

2010-01-01

.... (b) Layout. Figures 4, 5, and 5.1 are prototype labels that demonstrate the proper layout. All positioning, spacing, type size, and line widths shall be similar to and consistent with the prototype labels... and 71/2 inches (19.05 cm) long. Figure 4 of appendix A represents the prototype for the labels for...

TEM Analyses of Itokawa Regolith Grains and Lunar Soil Grains to Directly Determine Space Weathering Rates on Airless Bodies

NASA Technical Reports Server (NTRS)

Berger, Eve L.; Keller, Lindsay P.; Christoffersen, Roy

2016-01-01

Samples returned from the moon and Asteroid Itokawa by NASA's Apollo Missions and JAXA's Hayabusa Mission, respectively, provide a unique record of their interaction with the space environment. Space weathering effects result from micrometeorite impact activity and interactions with the solar wind. While the effects of solar wind interactions, ion implantation and solar flare particle track accumulation, have been studied extensively, the rate at which these effects accumulate in samples on airless bodies has not been conclusively determined. Results of numerical modeling and experimental simulations do not converge with observations from natural samples. We measured track densities and rim thicknesses of three olivine grains from Itokawa and multiple olivine and anorthite grains from lunar soils of varying exposure ages. Samples were prepared for analysis using a Leica EM UC6 ultramicrotome and an FEI Quanta 3D dual beam focused ion beam scanning electron microscope (FIB-SEM). Transmission electron microscope (TEM) analyses were performed on the JEOL 2500SE 200kV field emission STEM. The solar wind damaged rims on lunar anorthite grains are amorphous, lack inclusions, and are compositionally similar to the host grain. The rim width increases as a smooth function of exposure age until it levels off at approximately 180 nm after approximately 20 My (Fig. 1). While solar wind ion damage can only accumulate while the grain is in a direct line of sight to the Sun, solar flare particles can penetrate to mm-depths. To assess whether the track density accurately predicts surface exposure, we measured the rim width and track density in olivine and anorthite from the surface of rock 64455, which was never buried and has a surface exposure age of 2 My based on isotopic measurements. The rim width from 64455 (60-70nm) plots within error of the well-defined trend for solar wind amorphized rims in Fig. 1. Measured solar flare track densities are accurately reflecting the surface exposure of the grains. Track densities correlate with the amorphous rim thicknesses. While the space-weathered rims of anorthite grains are amorphous, the space-weathered rims on both Itokawa and lunar olivine grains show solar wind damaged rims that are not amorphous. Instead, the rims are nanocrystalline with high dislocation densities and sparse inclusions of nanophase Fe metal. The rim thicknesses on the olivine grains also correlate with track density. The Itokawa olivine grains have track densities that indicate surface exposures of approximately 10(exp 5) years. Longer exposures (up to approximately 10(exp 7) years) do not amorphize the rims, as evidenced by lunar soil olivines with high track densities (approximately 10(exp 11) cm(exp -2)). From the combined data, shown in Fig. 1, it is clear that olivine is damaged (but not amorphized) more rapidly by the solar wind compared to anorthite. The olivine damaged rim forms quickly (in approximately 10(exp 6) y) and saturates at approximately 120nm with longer exposure time. The anorthite damaged rims form more slowly, amorphize, and grow thicker than the olivine rims. This is in agreement with numerical modeling data which predicts that solar wind damaged rims on anorthite will be thicker than olivine. However, the models predict that both olivine and anorthite rims will amorphize and reach equilibrium widths in less than 10(exp 3) y, in contrast to what is observed for natural samples. Laboratory irradiation experiments, which show rapid formation of fully amorphous and blistered surfaces from simulated solar wind exposures are also in contrast to observations of natural samples. These results suggest that there is a flux dependence on the type and extent of irradiation damage that develops in olivine. This flux dependence suggests that great caution be used in extrapolating between high-flux laboratory experiments and the natural case, as demonstrated by. We constrain the space weathering rate through analysis of returned samples. Provided that the track densities and the solar wind damaged rim widths exhibited by the Itokawa grains are typical of the fine-grained regions of Itokawa, then the space weathering rate is on the order of 10(exp 5) y. Space weathering effects in lunar soils saturate within a few My of exposure while those in Itokawa regolith grains formed in approximately 10(exp 5) y. Olivine and anorthite respond differently to solar wind irradiation. The space weathering effects in olivine are particularly difficult to reconcile with laboratory irradiation studies and numerical models. Additional measurements, experiments, and modeling are required to resolve the discrepancies among the observations and calculations involving solar wind amorphization of different minerals on airless bodies.

High-speed microstrip multi-anode multichannel plate detector system

NASA Astrophysics Data System (ADS)

Riedo, Andreas; Tulej, Marek; Rohner, Urs; Wurz, Peter

2017-04-01

High-speed detector systems with high dynamic range and pulse width characteristics in the sub-nanosecond regime are mandatory for high resolution and highly sensitive time-of-flight mass spectrometers. Typically, for a reasonable detector area, an impedance-matched anode design is necessary to transmit the registered signal fast and distortion-free from the anode to the signal acquisition system. In this report, a high-speed microstrip multi-anode multichannel plate detector is presented and discussed. The anode consists of four separate active concentric anode segments allowing a simultaneous readout of signal with a dynamic range of about eight orders of magnitude. The impedance matched anode segments show pulse width of about 250 ps, measured at full width at half maximum, and rise time of ˜170 ps, measured with an oscilloscope with a sampling rate of 20 GS/s and 4 GHz analogue bandwidth. The usage of multichannel plates as signal amplifier allowed the design of a lightweight, low power consuming, and compact detector system, suitable, e.g., for the integration into space instrumentation or portable systems where size, weight, and power consumption are limited parameters.

Cavity detection and delineation research. Part 4: Microgravimetric survey: Manatee Springs Site, Florida

NASA Astrophysics Data System (ADS)

Butler, D. K.; Whitten, C. B.; Smith, F. L.

1983-03-01

Results of a microgravimetric survey at Manatee Springs, Levy County, Fla., are presented. The survey area was 100 by 400 ft, with 20-ft gravity station spacing, and with the long dimension of the area approximately perpendicular to the known trend of the main cavity. The main cavity is about 80 to 100 ft below the surface and has a cross section about 16 to 20 ft in height and 30 to 40 ft in width beneath the survey area. Using a density contrast of -1.3 g/cucm, the gravity anomaly is calculated to be -35 micro Gal with a width at half maximum of 205 ft. The microgravimetric survey results clearly indicate a broad negative anomaly coincident with the location and trend of the cavity system across the survey area. The anomaly magnitude and width are consistent with those calculated from the known depth and dimensions of the main cavity. In addition, a small, closed negative anomaly feature, superimposed on the broad negative feature due to the main cavity, satisfactorily delineated a small secondary cavity feature which was discovered and mapped by cave divers.

Multi-objective optimization of MOSFETs channel widths and supply voltage in the proposed dual edge-triggered static D flip-flop with minimum average power and delay by using fuzzy non-dominated sorting genetic algorithm-II.

PubMed

Keivanian, Farshid; Mehrshad, Nasser; Bijari, Abolfazl

2016-01-01

D Flip-Flop as a digital circuit can be used as a timing element in many sophisticated circuits. Therefore the optimum performance with the lowest power consumption and acceptable delay time will be critical issue in electronics circuits. The newly proposed Dual-Edge Triggered Static D Flip-Flop circuit layout is defined as a multi-objective optimization problem. For this, an optimum fuzzy inference system with fuzzy rules is proposed to enhance the performance and convergence of non-dominated sorting Genetic Algorithm-II by adaptive control of the exploration and exploitation parameters. By using proposed Fuzzy NSGA-II algorithm, the more optimum values for MOSFET channel widths and power supply are discovered in search space than ordinary NSGA types. What is more, the design parameters involving NMOS and PMOS channel widths and power supply voltage and the performance parameters including average power consumption and propagation delay time are linked. To do this, the required mathematical backgrounds are presented in this study. The optimum values for the design parameters of MOSFETs channel widths and power supply are discovered. Based on them the power delay product quantity (PDP) is 6.32 PJ at 125 MHz Clock Frequency, L = 0.18 µm, and T = 27 °C.

Cellulose structure and lignin distribution in normal and compression wood of the Maidenhair tree (Ginkgo biloba L.).

PubMed

Andersson, Seppo; Wang, Yurong; Pönni, Raili; Hänninen, Tuomas; Mononen, Marko; Ren, Haiqing; Serimaa, Ritva; Saranpää, Pekka

2015-04-01

We studied in detail the mean microfibril angle and the width of cellulose crystals from the pith to the bark of a 15-year-old Maidenhair tree (Ginkgo biloba L.). The orientation of cellulose microfibrils with respect to the cell axis and the width and length of cellulose crystallites were determined using X-ray diffraction. Raman microscopy was used to compare the lignin distribution in the cell wall of normal/opposite and compression wood, which was found near the pith. Ginkgo biloba showed a relatively large mean microfibril angle, varying between 19° and 39° in the S2 layer, and the average width of cellulose crystallites was 3.1-3.2 nm. Mild compression wood without any intercellular spaces or helical cavities was observed near the pith. Slit-like bordered pit openings and a heavily lignified S2L layer confirmed the presence of compression wood. Ginkgo biloba showed typical features present in the juvenile wood of conifers. The microfibril angle remained large over the 14 annual rings. The entire stem disc, with a diameter of 18 cm, was considered to consist of juvenile wood. The properties of juvenile and compression wood as well as the cellulose orientation and crystalline width indicate that the wood formation of G. biloba is similar to that of modern conifers. © 2015 Institute of Botany, Chinese Academy of Sciences.

Broadband optical frequency comb generator based on driving N-cascaded modulators by Gaussian-shaped waveform

NASA Astrophysics Data System (ADS)

Hmood, Jassim K.; Harun, Sulaiman W.

2018-05-01

A new approach for realizing a wideband optical frequency comb (OFC) generator based on driving cascaded modulators by a Gaussian-shaped waveform, is proposed and numerically demonstrated. The setup includes N-cascaded MZMs, a single Gaussian-shaped waveform generator, and N-1 electrical time delayer. The first MZM is driven directly by a Gaussian-shaped waveform, while delayed replicas of the Gaussian-shaped waveform drive the other MZMs. An analytical model that describes the proposed OFC generator is provided to study the effect of number and chirp factor of cascaded MZM as well as pulse width on output spectrum. Optical frequency combs at frequency spacing of 1 GHz are generated by applying Gaussian-shaped waveform at pulse widths ranging from 200 to 400 ps. Our results reveal that, the number of comb lines is inversely proportional to the pulse width and directly proportional to both number and chirp factor of cascaded MZMs. At pulse width of 200 ps and chirp factor of 4, 67 frequency lines can be measured at output spectrum of two-cascaded MZMs setup. Whereas, increasing the number of cascaded stages to 3, 4, and 5, the optical spectra counts 89, 109 and 123 frequency lines; respectively. When the delay time is optimized, 61 comb lines can be achieved with power fluctuations of less than 1 dB for five-cascaded MZMs setup.

Design of a QA method to characterize submillimeter-sized PBS beam properties using a 2D ionization chamber array

NASA Astrophysics Data System (ADS)

Lin, Yuting; Bentefour, Hassan; Flanz, Jacob; Kooy, Hanne; Clasie, Benjamin

2018-05-01

Pencil beam scanning (PBS) periodic quality assurance (QA) programs ensure the beam delivered to patients is within technical specifications. Two critical specifications for PBS delivery are the beam width and position. The aim of this study is to investigate whether a 2D ionization chamber array, such as the MatriXX detector (IBA Dosimetry, Schwarzenbruck, Germany), can be used to characterize submillimeter-sized PBS beam properties. The motivation is to use standard equipment, which may have pixel spacing coarser than the pencil beam size, and simplify QA workflow. The MatriXX pixels are cylindrical in shape with 4.5 mm diameter and are spaced 7.62 mm from center to center. Two major effects limit the ability of using the MatriXX to measure the spot position and width accurately. The first effect is that too few pixels sample the Gaussian shaped pencil beam profile and the second effect is volume averaging of the Gaussian profile over the pixel sensitive volumes. We designed a method that overcomes both limitations and hence enables the use of the MatriXX to characterize sub-millimeter-sized PBS beam properties. This method uses a cross-like irradiation pattern that is designed to increase the number of sampling data points and a modified Gaussian fitting technique to correct for volume averaging effects. Detector signals were calculated in this study and random noise and setup errors were added to simulate measured data. With the techniques developed in this work, the MatriXX detector can be used to characterize the position and width of sub-millimeter, σ  =  0.7 mm, sized pencil beams with uncertainty better than 3% relative to σ. With the irradiation only covering 60% of the MatriXX, the position and width of σ  =  0.9 mm sized pencil beams can be determined with uncertainty better than 3% relative to σ. If one were to not use a cross-like irradiation pattern, then the position and width of σ  =  3.6 mm sized pencil beams can be determined with uncertainty better than 3% relative to σ. If one were to not use a cross-like pattern nor volume averaging corrections, then the position and width of σ  =  5.0 mm sized pencil beams can be determined with uncertainty better than 3% relative to σ. This work helps to simplify periodic QA in proton therapy because more routinely used ionization chamber arrays can be used to characterize narrow pencil beam properties.

Design of a QA method to characterize submillimeter-sized PBS beam properties using a 2D ionization chamber array.

PubMed

Lin, Yuting; Bentefour, Hassan; Flanz, Jacob; Kooy, Hanne; Clasie, Benjamin

2018-05-15

Pencil beam scanning (PBS) periodic quality assurance (QA) programs ensure the beam delivered to patients is within technical specifications. Two critical specifications for PBS delivery are the beam width and position. The aim of this study is to investigate whether a 2D ionization chamber array, such as the MatriXX detector (IBA Dosimetry, Schwarzenbruck, Germany), can be used to characterize submillimeter-sized PBS beam properties. The motivation is to use standard equipment, which may have pixel spacing coarser than the pencil beam size, and simplify QA workflow. The MatriXX pixels are cylindrical in shape with 4.5 mm diameter and are spaced 7.62 mm from center to center. Two major effects limit the ability of using the MatriXX to measure the spot position and width accurately. The first effect is that too few pixels sample the Gaussian shaped pencil beam profile and the second effect is volume averaging of the Gaussian profile over the pixel sensitive volumes. We designed a method that overcomes both limitations and hence enables the use of the MatriXX to characterize sub-millimeter-sized PBS beam properties. This method uses a cross-like irradiation pattern that is designed to increase the number of sampling data points and a modified Gaussian fitting technique to correct for volume averaging effects. Detector signals were calculated in this study and random noise and setup errors were added to simulate measured data. With the techniques developed in this work, the MatriXX detector can be used to characterize the position and width of sub-millimeter, σ  =  0.7 mm, sized pencil beams with uncertainty better than 3% relative to σ. With the irradiation only covering 60% of the MatriXX, the position and width of σ  =  0.9 mm sized pencil beams can be determined with uncertainty better than 3% relative to σ. If one were to not use a cross-like irradiation pattern, then the position and width of σ  =  3.6 mm sized pencil beams can be determined with uncertainty better than 3% relative to σ. If one were to not use a cross-like pattern nor volume averaging corrections, then the position and width of σ  =  5.0 mm sized pencil beams can be determined with uncertainty better than 3% relative to σ. This work helps to simplify periodic QA in proton therapy because more routinely used ionization chamber arrays can be used to characterize narrow pencil beam properties.

Statistics of the radiated field of a space-to-earth microwave power transfer system

NASA Technical Reports Server (NTRS)

Stevens, G. H.; Leininger, G.

1976-01-01

Statistics such as average power density pattern, variance of the power density pattern and variance of the beam pointing error are related to hardware parameters such as transmitter rms phase error and rms amplitude error. Also a limitation on spectral width of the phase reference for phase control was established. A 1 km diameter transmitter appears feasible provided the total rms insertion phase errors of the phase control modules does not exceed 10 deg, amplitude errors do not exceed 10% rms, and the phase reference spectral width does not exceed approximately 3 kHz. With these conditions the expected radiation pattern is virtually the same as the error free pattern, and the rms beam pointing error would be insignificant (approximately 10 meters).

Stabilizing detached Bridgman melt crystal growth: Model-based nonlinear feedback control

NASA Astrophysics Data System (ADS)

Yeckel, Andrew; Daoutidis, Prodromos; Derby, Jeffrey J.

2012-12-01

The dynamics and operability limits of a nonlinear-proportional-integral controller designed to stabilize detached vertical Bridgman crystal growth are studied. The manipulated variable is the pressure difference between upper and lower vapor spaces, and the controlled variable is the gap width at the triple-phase line. The controller consists of a model-based nonlinear component coupled with a standard proportional-integral controller. The nonlinear component is based on a capillary model of shape stability. Perturbations to gap width, pressure difference, wetting angle, and growth angle are studied under both shape stable and shape unstable conditions. The nonlinear-PI controller allows a wider operating range of gain than a standard PI controller used alone, is easier to tune, and eliminates solution multiplicity from closed-loop operation.

Domain wall structure and interactions in 50 nm wide Cobalt nanowires

NASA Astrophysics Data System (ADS)

Tu, Kun-Hua; Ojha, Shuchi; Ross, Caroline A.

2018-05-01

Arrays of cobalt nanowires with widths of 50 nm, thickness of 5 and 20 nm and periodicity of 70 nm were fabricated by pattern transfer from a self-assembled block copolymer film. Transverse domain walls (DWs) were imaged by magnetic force microscopy, indicating repulsive interactions between DWs of the same sign in the 20 nm thick wires. Micromagnetic simulations were used to identify the interactions in the six distinct cases of a pair of transverse DWs in adjacent wires, considering all the possible combinations of head-to-head and tail-to-tail DWs and the orientation of the core magnetization. The boundary between repulsive and attractive DW interactions is mapped out for wires as a function of thickness, width and interwire spacing.

Deployment of the P4 Truss SAW during Expedition 13 / STS-115 Joint Operations

NASA Image and Video Library

2006-09-15

S115-E-06184 (14 Sept. 2006) --- Space Shuttle Atlantis astronauts spread a second set of wings for the International Space Station today. The new solar arrays were fully extended at 7:44 a.m. (CDT). The new arrays span a total of 240 feet and have a width of 38 feet. They are attached to the station's newest component, the P3/P4 integrated truss segment. The installation of the P3/P4, which occurred Sept. 12 and the deployment of the arrays set the stage for future expansion of the station.

Second set of solar arrays on the ISS during Expedition 13 / STS-115 Joint Operations

NASA Image and Video Library

2006-09-14

S115-E-06052 (14 Sept. 2006) --- Space Shuttle Atlantis astronauts spread a second set of wings for the International Space Station today. The new solar arrays were fully extended at 7:44 a.m. (CDT). The new arrays span a total of 240 feet and have a width of 38 feet. They are attached to the station's newest component, the P3/P4 integrated truss segment. The installation of the P3/P4, which occurred Tuesday, and the deployment of the arrays set the stage for future expansion of the station.

Deployment of the P4 Truss SAW during Expedition 13 / STS-115 Joint Operations

NASA Image and Video Library

2006-09-15

S115-E-06186 (14 Sept. 2006) --- Space Shuttle Atlantis astronauts spread a second set of wings for the International Space Station today. The new solar arrays were fully extended at 7:44 a.m. (CDT). The new arrays span a total of 240 feet and have a width of 38 feet. They are attached to the station's newest component, the P3/P4 integrated truss segment. The installation of the P3/P4, which occurred Sept. 12 and the deployment of the arrays set the stage for future expansion of the station.

Deployment of the P4 Truss FWD SAW during Expedition 13 and STS-115 EVA Joint Operations

NASA Image and Video Library

2006-09-14

S115-E-05996 (14 Sept. 2006) --- Space Shuttle Atlantis astronauts spread a second set of wings for the International Space Station today. The new solar arrays were fully extended at 7:44 a.m. (CDT). The new arrays span a total of 240 feet and have a width of 38 feet. They are attached to the station's newest component, the P3/P4 integrated truss segment. The installation of the P3/P4, which occurred Tuesday and the deployment of the arrays set the stage for future expansion of the station.

P4 Truss FWD SAW during Expedition 13 and STS-115 EVA Joint Operations

NASA Image and Video Library

2006-09-14

S115-E-05999 (14 Sept. 2006) --- Space Shuttle Atlantis astronauts spread a second set of wings for the International Space Station today. The new solar arrays were fully extended at 7:44 a.m CDT. The new arrays span a total of 240 feet and have a width of 38 feet. They are attached to the station's newest component, the P3/P4 integrated truss segment. The installation of the P3/P4, which occurred Tuesday, and the deployment of the arrays set the stage for future expansion of the station.

Microgravity

NASA Image and Video Library

2000-01-30

Engineers from NASA's Glenn Research Center demonstrate the access to one of the experiment racks planned for the U.S. Destiny laboratory module on the International Space Station (ISS). This mockup has the full diameter, full corridor width, and half the length of the module. The mockup includes engineering mockups of the Fluids and Combustion Facility being developed by NASA's Glenn Research Center. (The full module will be six racks long; the mockup is three racks long). Listening at center is former astronaut Brewster Shaw (center), now a program official with the Boeing Co., the ISS prime contractor. Photo credit: NASA/Marshall Space Flight Center (MSFC)

Emittance dilution and halo creation during the first milliseconds after injection at the Fermilab Booster

DOE Office of Scientific and Technical Information (OSTI.GOV)

Spentzouris, Panagiotis; Amundson, J.; /Fermilab

2005-01-01

During the past year, the Fermilab Booster has been pushed to record intensities in order to satisfy the needs of the Tevatron collider and neutrino programs. This high intensity makes the study of space-charge effects and halo formation highly relevant to optimizing Booster performance. We present measurements of beam width evolution, halo formation, and coherent tune shifts, emphasizing the experimental techniques used and the calibration of the measuring devices. We also use simulations utilizing the 3D space-charge code Synergia to study the physical origins of these effects.

A compact free space quantum key distribution system capable of daylight operation

NASA Astrophysics Data System (ADS)

Benton, David M.; Gorman, Phillip M.; Tapster, Paul R.; Taylor, David M.

2010-06-01

A free space quantum key distribution system has been demonstrated. Consideration has been given to factors such as field of view and spectral width, to cut down the deleterious effect from background light levels. Suitable optical sources such as lasers and RCLEDs have been investigated as well as optimal wavelength choices, always with a view to building a compact and robust system. The implementation of background reduction measures resulted in a system capable of operating in daylight conditions. An autonomous system was left running and generating shared key material continuously for over 7 days.

Significant Enhancement of MgZnO Metal-Semiconductor-Metal Photodetectors via Coupling with Pt Nanoparticle Surface Plasmons

NASA Astrophysics Data System (ADS)

Guo, Zexuan; Jiang, Dayong; Hu, Nan; Yang, Xiaojiang; Zhang, Wei; Duan, Yuhan; Gao, Shang; Liang, Qingcheng; Zheng, Tao; Lv, Jingwen

2018-06-01

We proposed and demonstrated MgZnO metal-semiconductor-metal (MSM) ultraviolet photodetectors (UV) assisted with surface plasmons (SPs) prepared by the radio frequency magnetron sputtering deposition method. After the decoration of their surface with Pt nanoparticles (NPs), the responsivity of all the electrode spacing (3, 5, and 8 μm) photodetectors were enhanced dramatically; to our surprise, comparing with them the responsivity of larger spacing sample, more SPs were gathered which are smaller than others in turn. A physical mechanism focused on SPs and depletion width is given to explain the above results.

(Congressional) Center for Microplasma Science and Technology

DTIC Science & Technology

2012-03-29

Flexible Tubing Plasma Jet (a.k.a plasma snake) We made the device using Ar and He as working gases, Teflon tubing, copper tape as electrode(s) and a...An advantage of these Cap‐DBDs over  planar or coaxial DBDs is their geometry; the open  space  surrounding each tube allows active species created by...plasma. The gap width between tubes influences both the area and shape of the Lissajous figures ( Figure 8, middle). For the larger spacing , the

Design of a ZVS PWM inverter for a brushless DC motor in an EMA application

NASA Technical Reports Server (NTRS)

Bell, J. Brett; Nelms, R. M.; Shepherd, Michael T.

1993-01-01

The Component Development Division of the Propulsion Laboratory at Marshall Space Flight Center (MSFC) is currently investigating the use of electromechanical actuators for use in space transportation applications such as Thrust Vector Control (TVC). These high power servomechanisms will require rugged, reliable, and compact power electronic modules capable of modulating several hundred amperes of current at up to 270 Vdc. This paper will discuss the design and implementation of a zero-voltage-switched PWM (Pulse Width Modulation) inverter which operates from a 270 Vdc source at currents up to 100 A.

Longitudinal changes of angle configuration in primary angle-closure suspects: the Zhongshan Angle-Closure Prevention Trial.

PubMed

Jiang, Yuzhen; Chang, Dolly S; Zhu, Haogang; Khawaja, Anthony P; Aung, Tin; Huang, Shengsong; Chen, Qianyun; Munoz, Beatriz; Grossi, Carlota M; He, Mingguang; Friedman, David S; Foster, Paul J

2014-09-01

To determine longitudinal changes in angle configuration in the eyes of primary angle-closure suspects (PACS) treated by laser peripheral iridotomy (LPI) and in untreated fellow eyes. Longitudinal cohort study. Primary angle-closure suspects aged 50 to 70 years were enrolled in a randomized, controlled clinical trial. Each participant was treated by LPI in 1 randomly selected eye, with the fellow eye serving as a control. Angle width was assessed in a masked fashion using gonioscopy and anterior segment optical coherence tomography (AS-OCT) before and at 2 weeks, 6 months, and 18 months after LPI. Angle width in degrees was calculated from Shaffer grades assessed under static gonioscopy. Angle configuration was also evaluated using angle opening distance (AOD250, AOD500, AOD750), trabecular-iris space area (TISA500, TISA750), and angle recess area (ARA) measured in AS-OCT images. No significant difference was found in baseline measures of angle configuration between treated and untreated eyes. At 2 weeks after LPI, the drainage angle on gonioscopy widened from a mean of 13.5° at baseline to a mean of 25.7° in treated eyes, which was also confirmed by significant increases in all AS-OCT angle width measures (P<0.001 for all variables). Between 2 weeks and 18 months after LPI, a significant decrease in angle width was observed over time in treated eyes (P<0.001 for all variables), although the change over the first 5.5 months was not statistically significant for angle width measured under gonioscopy (P = 0.18), AOD250 (P = 0.167) and ARA (P = 0.83). In untreated eyes, angle width consistently decreased across all follow-up visits after LPI, with a more rapid longitudinal decrease compared with treated eyes (P values for all variables ≤0.003). The annual rate of change in angle width was equivalent to 1.2°/year (95% confidence interval [CI], 0.8-1.6) in treated eyes and 1.6°/year (95% CI, 1.3-2.0) in untreated eyes (P<0.001). Angle width of treated eyes increased markedly after LPI, remained stable for 6 months, and then decreased significantly by 18 months after LPI. Untreated eyes experienced a more consistent and rapid decrease in angle width over the same time period. Copyright © 2014 American Academy of Ophthalmology. Published by Elsevier Inc. All rights reserved.

Complex energies and the polyelectronic Stark problem

NASA Astrophysics Data System (ADS)

Themelis, Spyros I.; Nicolaides, Cleanthes A.

2000-12-01

The problem of computing the energy shifts and widths of ground or excited N-electron atomic states perturbed by weak or strong static electric fields is dealt with by formulating a state-specific complex eigenvalue Schrödinger equation (CESE), where the complex energy contains the field-induced shift and width. The CESE is solved to all orders nonperturbatively, by using separately optimized N-electron function spaces, composed of real and complex one-electron functions, the latter being functions of a complex coordinate. The use of such spaces is a salient characteristic of the theory, leading to economy and manageability of calculation in terms of a two-step computational procedure. The first step involves only Hermitian matrices. The second adds complex functions and the overall computation becomes non-Hermitian. Aspects of the formalism and of computational strategy are compared with those of the complex absorption potential (CAP) method, which was recently applied for the calculation of field-induced complex energies in H and Li. Also compared are the numerical results of the two methods, and the questions of accuracy and convergence that were posed by Sahoo and Ho (Sahoo S and Ho Y K 2000 J. Phys. B: At. Mol. Opt. Phys. 33 2195) are explored further. We draw attention to the fact that, because in the region where the field strength is weak the tunnelling rate (imaginary part of the complex eigenvalue) diminishes exponentially, it is possible for even large-scale nonperturbative complex eigenvalue calculations either to fail completely or to produce seemingly stable results which, however, are wrong. It is in this context that the discrepancy in the width of Li 1s22s 2S between results obtained by the CAP method and those obtained by the CESE method is interpreted. We suggest that the very-weak-field regime must be computed by the golden rule, provided the continuum is represented accurately. In this respect, existing one-particle semiclassical formulae seem to be sufficient. In addition to the aforementioned comparisons and conclusions, we present a number of new results from the application of the state-specific CESE theory to the calculation of field-induced shifts and widths of the H n = 3 levels and of the prototypical Be 1s22s2 1S state, for a range of field strengths. Using the H n = 3 manifold as the example, it is shown how errors may occur for small values of the field, unless the function spaces are optimized carefully for each level.

Girdling eastern black walnut to increase heartwood width

Treesearch

Larry D. Godsey; W.D. " Dusty" Walter; H.E. " Gene" Garrett

2004-01-01

Eastern black walnut (Juglans nigra L.) has often been planted at spacings that require pre-commercial thinning. These thinnings are deemed pre-commercial due to the small diameter of the trees and the low ratio of dark wood to light wood. As a consequence of size and wood quality, these thinnings are often an expense rather than a source of revenue...

Multifunctional Antenna Techniques

DTIC Science & Technology

2015-11-25

the planar structure that can be sufficiently isolated from the radiation mechanism of the antenna and transformed into a TEM transmission line feed...an equivalent transmission line structure, and isolate the physical 5 | P a g e mechanisms responsible for impedance and radiation behavior...gap-fed Archimedean spiral antenna in free space with non-negligible metal width, insertion PMC boundaries to isolate the radiation and propagation

Effects of Typographic Variables on Eye-Movement Measures in Reading Chinese from a Screen

ERIC Educational Resources Information Center

Yen, Nai-Shing; Tsai, Jie-Li; Chen, Pei-Ling; Lin, Hsuan-Yu; Chen, Arbee L. P.

2011-01-01

To investigate the most efficient way to represent text in reading Chinese on computer displays, three typographic variables, character size (41[feet] arc/24 pixels and 60[feet] arc/32 pixels), character spacing (1/4 and 1/8 character width) and font type (Kai and Ming), were manipulated. Results showed that the reading speed for Chinese…

Calculation of the Energy-Band Structure of the Kronig-Penney Model Using the Nearly-Free and Tightly-Bound-Electron Approximations

ERIC Educational Resources Information Center

Wetsel, Grover C., Jr.

1978-01-01

Calculates the energy-band structure of noninteracting electrons in a one-dimensional crystal using exact and approximate methods for a rectangular-well atomic potential. A comparison of the two solutions as a function of potential-well depth and ratio of lattice spacing to well width is presented. (Author/GA)

PHYSICAL EFFECTS OCCURRING DURING GENERATION AND AMPLIFICATION OF LASER RADIATION: Spatial phase fluctuations of the fundamental laser mode caused by spontaneous emission

NASA Astrophysics Data System (ADS)

Belinskiĭ, A. V.; Chirkin, Anatolii S.

1989-02-01

A calculation is reported of the degree of spatial coherence of the fundamental radiation mode subject to phase fluctuations in space. It is shown that the degree of spatial coherence (within the beam width) is perturbed only slightly by these fluctuations, compared with subthreshold excitation of higher transverse modes.

Nonlinear optical susceptibilities in the diffusion modified AlxGa1-xN/GaN single quantum well

NASA Astrophysics Data System (ADS)

Das, T.; Panda, S.; Panda, B. K.

2018-05-01

Under thermal treatment of the post growth AlGaN/GaN single quantum well, the diffusion of Al and Ga atoms across the interface is expected to form the diffusion modified quantum well with diffusion length as a quantitative parameter for diffusion. The modification of confining potential and position-dependent effective mass in the quantum well due to diffusion is calculated taking the Fick's law. The built-in electric field which arises from spontaneous and piezoelectric polarizations in the wurtzite structure is included in the effective mass equation. The electronic states are calculated from the effective mass equation using the finite difference method for several diffusion lengths. Since the effective well width decreases with increasing diffusion length, the energy levels increase with it. The intersubband energy spacing in the conduction band decreases with diffusion length due to built-in electric field and reduction of effective well width. The linear susceptibility for first-order and the nonlinear second-order and third-order susceptibilities are calculated using the compact density matrix approach taking only two levels. The calculated susceptibilities are red shifted with increase in diffusion lengths due to decrease in intersubband energy spacing.

Extension of Miles Equation for Ring Baffle Damping Predictions to Small Slosh Amplitudes and Large Baffle Widths

NASA Technical Reports Server (NTRS)

West, Jeff; Yang, H. Q.; Brodnick, Jacob; Sansone, Marco; Westra, Douglas

2016-01-01

The Miles equation has long been used to predict slosh damping in liquid propellant tanks due to ring baffles. The original work by Miles identifies defined limits to its range of application. Recent evaluations of the Space Launch System identified that the Core Stage baffle designs resulted in violating the limits of the application of the Miles equation. This paper describes the work conducted by NASA/MSFC to develop methods to predict slosh damping from ring baffles for conditions for which Miles equation is not applicable. For asymptotically small slosh amplitudes or conversely large baffle widths, an asymptotic expression for slosh damping was developed and calibrated using historical experimental sub-scale slosh damping data. For the parameter space that lies between region of applicability of the asymptotic expression and the Miles equation, Computational Fluid Dynamics simulations of slosh damping were used to develop an expression for slosh damping. The combined multi-regime slosh prediction methodology is shown to be smooth at regime boundaries and consistent with both sub-scale experimental slosh damping data and the results of validated Computational Fluid Dynamics predictions of slosh damping due to ring baffles.

Genetic association studies in osteoarthritis: is it fairytale?

PubMed

Warner, Sophie C; Valdes, Ana M

2017-01-01

Osteoarthritis is a common complex disorder with a strong genetic component. Other identified risk factors such as increasing age and overweight do not fully explain the risk of osteoarthritis. Here, we highlight the main findings from genetic association studies on osteoarthritis to date. Currently, genetic association studies have identified 21 independent susceptibility loci for osteoarthritis. Studies have focused on hip, knee and hand osteoarthritis, as well as posttotal joint replacement and minimum joint space width, a proxy for cartilage thickness. Four distinct loci have recently been identified in a genome-wide association scan on minimum joint space width. The role of mitochondrial DNA variants has been the focus of a recent meta-analysis. Findings have previously been mixed, however, this study suggests a plausible involvement of mitochondrial DNA in the progression of radiographic knee osteoarthritis. Identifying genetic locations of interest provides a framework upon which to base future studies, for example replication analysis and functional work. Genetic association studies have shaped and will continue to shape research in this field. Improving the understanding of osteoarthritis could improve the diagnosis and treatment of the disease and improve quality of life for many individuals.

Graphene/semicrystalline-carbon derived from amylose films for supercapacitor application

NASA Astrophysics Data System (ADS)

Deraman, M.; Sazali, N. E. S.; Hanappi, M. F. Y. M.; Tajuddin, N. S. M.; Hamdan, E.; Suleman, M.; Othman, M. A. R.; Omar, R.; Hashim, M. A.; Basri, N. H.; Nor, N. S. M.; Dolah, B. N. M.; Noor, A. M.; Jasni, M. R. M.

2016-08-01

Graphene/semicrystalline-carbon in the form of carbon flakes is produced by carbonization up to 600, 700, 800, 900 and 1000°C, respectively, of the amylose films prepared by a casting method on copper foil substrate. The carbon flakes are characterized by X-ray diffraction (XRD) method to determine their microcrystallite interlayer spacing, width and stack-height; and Raman spectroscopy (RS) method to obtain structural information from the D-, D2- and G-bands peak-intensities. The XRD results show that increase in carbonization temperature lead to ~(1-3%), ~85% and ~30%increase in the microcrystallites interlayer spacing, width and stack-height, respectively, indicating that a larger growth of microcrytallite of carbon flakes occurs in the direction parallel to (001) plane or film planar surface. The specific surface area of carbon flakes estimated from the XRD results in decreases from ~4400 to ~3400 m2/g, corresponding to the specific capacitance between ~500 to ~400 F/g, which are well within the range of specific capacitance for typical electrodes carbon for supercapacitor application. The RS results show that the multilayer graphene co-exist with semicrystalline- carbon within the carbon flakes, with the multilayer graphene relative quantities increase with increasing carbonization temperature.

Optimization of a Focusable and Rotatable Shear-Wave Periodic Permanent Magnet Electromagnetic Acoustic Transducers for Plates Inspection

PubMed Central

Qiu, Gongzhe

2017-01-01

Due to the symmetry of conventional periodic-permanent-magnet electromagnetic acoustic transducers (PPM EMATs), two shear (SH) waves can be generated and propagated simultaneously in opposite directions, which makes the signal recognition and interpretation complicatedly. Thus, this work presents a new SH wave PPM EMAT design, rotating the parallel line sources to realize the wave beam focusing in a single-direction. The theoretical model of distributed line sources was deduced firstly, and the effects of some parameters, such as the inner coil width, adjacent line sources spacing and the angle between parallel line sources, on SH wave focusing and directivity were studied mainly with the help of 3D FEM. Employing the proposed PPM EMATs, some experiments are carried out to verify the reliability of FEM simulation. The results indicate that rotating the parallel line sources can strength the wave on the closing side of line sources, decreasing the inner coil width and the adjacent line sources spacing can improve the amplitude and directivity of signals excited by transducers. Compared with traditional PPM EMATs, both the capacity of unidirectional excitation and directivity of the proposed PPM EMATs are improved significantly. PMID:29186790

The Rapidity Density Distributions and Longitudinal Expansion Dynamics of Identified Pions from the STAR Beam Energy Scan

NASA Astrophysics Data System (ADS)

Flores, Christopher E.

2016-12-01

The Beam Energy Scan (BES) at the Relativistic Heavy-Ion Collider was proposed to characterize the properties of the medium produced in heavy-ion interactions over a broad range of baryon chemical potential. The aptitude of the STAR detector for mid-rapidity measurements has previously been leveraged to measure identified particle yields and spectra to extract bulk properties for the BES energies for | y | ≤ 0.1. However, to extract information on expansion dynamics and full phase space particle production, it is necessary to study identified particle rapidity density distributions. We present the first rapidity density distributions of identified pions from Au+Au collisions at √{sNN} = 7.7 , 11.5, and 19.6 GeV from the BES program as measured by the STAR detector. We use these distributions to obtain the full phase space yields of the pions to provide additional information of the system's chemistry. Further, we report the width of the rapidity density distributions compared to the width expected from Landau hydrodynamics. Finally, we interpret the results as a function of collision energy and discuss them in the context of previous energy scans done at the AGS and SPS.

An adaptive neuro fuzzy inference system controlled space cector pulse width modulation based HVDC light transmission system under AC fault conditions

NASA Astrophysics Data System (ADS)

Ajay Kumar, M.; Srikanth, N. V.

2014-03-01

In HVDC Light transmission systems, converter control is one of the major fields of present day research works. In this paper, fuzzy logic controller is utilized for controlling both the converters of the space vector pulse width modulation (SVPWM) based HVDC Light transmission systems. Due to its complexity in the rule base formation, an intelligent controller known as adaptive neuro fuzzy inference system (ANFIS) controller is also introduced in this paper. The proposed ANFIS controller changes the PI gains automatically for different operating conditions. A hybrid learning method which combines and exploits the best features of both the back propagation algorithm and least square estimation method is used to train the 5-layer ANFIS controller. The performance of the proposed ANFIS controller is compared and validated with the fuzzy logic controller and also with the fixed gain conventional PI controller. The simulations are carried out in the MATLAB/SIMULINK environment. The results reveal that the proposed ANFIS controller is reducing power fluctuations at both the converters. It also improves the dynamic performance of the test power system effectively when tested for various ac fault conditions.

Optimization of a Focusable and Rotatable Shear-Wave Periodic Permanent Magnet Electromagnetic Acoustic Transducers for Plates Inspection.

PubMed

Song, Xiaochun; Qiu, Gongzhe

2017-11-24

Due to the symmetry of conventional periodic-permanent-magnet electromagnetic acoustic transducers (PPM EMATs), two shear (SH) waves can be generated and propagated simultaneously in opposite directions, which makes the signal recognition and interpretation complicatedly. Thus, this work presents a new SH wave PPM EMAT design, rotating the parallel line sources to realize the wave beam focusing in a single-direction. The theoretical model of distributed line sources was deduced firstly, and the effects of some parameters, such as the inner coil width, adjacent line sources spacing and the angle between parallel line sources, on SH wave focusing and directivity were studied mainly with the help of 3D FEM. Employing the proposed PPM EMATs, some experiments are carried out to verify the reliability of FEM simulation. The results indicate that rotating the parallel line sources can strength the wave on the closing side of line sources, decreasing the inner coil width and the adjacent line sources spacing can improve the amplitude and directivity of signals excited by transducers. Compared with traditional PPM EMATs, both the capacity of unidirectional excitation and directivity of the proposed PPM EMATs are improved significantly.

KSC-08pd2376

NASA Image and Video Library

2008-08-12

CAPE CANAVERAL, Fla. – A van travels the width of the Launch Pad 39A flame trench at NASA's Kennedy Space Center after tests of the repairs on the wall. Workers sprayed a heat-resistant concrete called Fondue Fyre into steel grid structures, welded to the wall of the flame trench. Fondue Fyre was developed during NASA's Apollo lunar program. Damage to the trench occurred during the launch of space shuttle Discovery on the STS-124 mission. A 75-foot by 20-foot section of the east wall was destroyed and debris scattered as far as the pad perimeter fence. Repairs being completed before the targeted Oct. 8 launch of Atlantis on the NASA Hubble Space Telescope servicing mission. Photo credit: NASA/Dimitri Gerondidakis

Space-qualified laser system for the BepiColombo Laser Altimeter.

PubMed

Kallenbach, Reinald; Murphy, Eamonn; Gramkow, Bodo; Rech, Markus; Weidlich, Kai; Leikert, Thomas; Henkelmann, Reiner; Trefzger, Boris; Metz, Bodo; Michaelis, Harald; Lingenauber, Kay; DelTogno, Simone; Behnke, Thomas; Thomas, Nicolas; Piazza, Daniele; Seiferlin, Karsten

2013-12-20

The space-qualified design of a miniaturized laser for pulsed operation at a wavelength of 1064 nm and at repetition rates up to 10 Hz is presented. This laser consists of a pair of diode-laser pumped, actively q-switched Nd:YAG rod oscillators hermetically sealed and encapsulated in an environment of dry synthetic air. The system delivers at least 300 million laser pulses with 50 mJ energy and 5 ns pulse width (FWHM). It will be launched in 2017 aboard European Space Agency's Mercury Planetary Orbiter as part of the BepiColombo Laser Altimeter, which, after a 6-years cruise, will start recording topographic data from orbital altitudes between 400 and 1500 km above Mercury's surface.

Measuring river from the cloud - River width algorithm development on Google Earth Engine

NASA Astrophysics Data System (ADS)

Yang, X.; Pavelsky, T.; Allen, G. H.; Donchyts, G.

2017-12-01

Rivers are some of the most dynamic features of the terrestrial land surface. They help distribute freshwater, nutrients, sediment, and they are also responsible for some of the greatest natural hazards. Despite their importance, our understanding of river behavior is limited at the global scale, in part because we do not have a river observational dataset that spans both time and space. Remote sensing data represent a rich, largely untapped resource for observing river dynamics. In particular, publicly accessible archives of satellite optical imagery, which date back to the 1970s, can be used to study the planview morphodynamics of rivers at the global scale. Here we present an image processing algorithm developed using the Google Earth Engine cloud-based platform, that can automatically extracts river centerlines and widths from Landsat 5, 7, and 8 scenes at 30 m resolution. Our algorithm makes use of the latest monthly global surface water history dataset and an existing Global River Width from Landsat (GRWL) dataset to efficiently extract river masks from each Landsat scene. Then a combination of distance transform and skeletonization techniques are used to extract river centerlines. Finally, our algorithm calculates wetted river width at each centerline pixel perpendicular to its local centerline direction. We validated this algorithm using in situ data estimated from 16 USGS gauge stations (N=1781). We find that 92% of the width differences are within 60 m (i.e. the minimum length of 2 Landsat pixels). Leveraging Earth Engine's infrastructure of collocated data and processing power, our goal is to use this algorithm to reconstruct the morphodynamic history of rivers globally by processing over 100,000 Landsat 5 scenes, covering from 1984 to 2013.

Relationship between iris surface features and angle width in Asian eyes.

PubMed

Sidhartha, Elizabeth; Nongpiur, Monisha Esther; Cheung, Carol Y; He, Mingguang; Wong, Tien Yin; Aung, Tin; Cheng, Ching-Yu

2014-10-23

To examine the associations between iris surface features with anterior chamber angle width in Asian eyes. In this prospective cross-sectional study, we recruited 600 subjects from a large population-based study, the Singapore Epidemiology of Eye Diseases (SEED) study. We obtained standardized digital slit-lamp iris photographs and graded the iris crypts (by number and size), furrows (by number and circumferential extent), and color (higher grade denoting darker iris). Vertical and horizontal cross-sections of anterior chamber were imaged using anterior segment optical coherence tomography. Angle opening distance (AOD), angle recess area (ARA), and trabecular-iris space area (TISA) were measured using customized software. Associations of the angle width with the iris surface features in the subject's right eyes were assessed using linear regression analysis. A total of 464 eyes of the 464 subjects (mean age: 57.5 ± 8.6 years) had complete and gradable data for crypts and color, and 423 eyes had gradable data for furrows. After adjustment for age, sex, ethnicity, pupil size, and corneal arcus, higher crypt grade was independently associated with wider AOD750 (β [change in angle width per grade higher] = 0.018, P = 0.023), ARA750 (β = 0.022, P = 0.049), and TISA750 (β = 0.011, P = 0.019), and darker iris was associated narrower ARA750 (β = -0.025, P = 0.044) and TISA750 (β = -0.013, P = 0.011). Iris surface features, assessed and measured from slit-lamp photographs, correlated well with anterior chamber angle width; irises with more crypts and lighter color were associated with wider angle. These findings may provide another imaging modality to assess angle closure risk based on iris surface features. Copyright 2014 The Association for Research in Vision and Ophthalmology, Inc.

Subject-Specific Finite Element Analysis of the Carpal Tunnel Cross-Sectional to Examine Tunnel Area Changes in Response to Carpal Arch Loading

PubMed Central

Walia, Piyush; Erdemir, Ahmet; Li, Zong-Ming

2017-01-01

Background Manipulating the carpal arch width (i.e. distance between hamate and trapezium bones) has been suggested as a means to increase carpal tunnel cross-sectional area and alleviate median nerve compression. The purpose of this study was to develop a finite element model of the carpal tunnel and to determine an optimal force direction to maximize area. Methods A planar geometric model of carpal bones at hamate level was reconstructed from MRI with inter-carpal joint spaces filled with a linear elastic surrogate tissue. Experimental data with discrete carpal tunnel pressures (50, 100, 150, and 200 mmHg) and corresponding carpal bone movements were used to obtain material property of surrogate tissue by inverse finite element analysis. The resulting model was used to simulate changes of carpal arch widths and areas with directional variations of a unit force applied at the hook of hamate. Findings Inverse finite element model predicted the experimental area data within 1.5% error. Simulation of force applications showed that carpal arch width and area were dependent on the direction of force application, and minimal arch width and maximal area occurred at 138° (i.e. volar-radial direction) with respect to the hamate-to-trapezium axis. At this force direction, the width changed to 24.4 mm from its initial 25.1 mm (3% decrease), and the area changed to 301.6 mm2 from 290.3 mm2 (4% increase). Interpretation The findings of the current study guide biomechanical manipulation to gain tunnel area increase, potentially helping reduce carpal tunnel pressure and relieve symptoms of compression median neuropathy. PMID:28073093

Regionally Varying Assessments of Tropical Width in Reanalyses and CMIP5 Models Using a Tropopause Break Metric

NASA Astrophysics Data System (ADS)

Homeyer, C. R.; Martin, E. R.; McKinzie, R.; McCarthy, K.

2017-12-01

The boundary between the tropics and the extratropics in each hemisphere is not fixed in space or time. Variations in the north-south width of the tropics are directly connected to changes in weather and climate. These fluctuations have been shown to impact tropical biodiversity, the spread of vector borne diseases, atmospheric chemistry, and additional natural and human sectors. However, there is no unanimous definition of the tropical boundary. This has led to a disagreement on the magnitude of changes in the tropical width during the past 30 years and a lack of understanding concerning its spatial and temporal variability. This study identifies the variability of the tropical width in modern reanalyses (ERA-Interim, JRA-55, CFSR, MERRA, and MERRA-2) and CMIP5 models (all models with available 6-hourly output) using a novel analysis metric: the tropopause "break" (i.e., the sharp discontinuity in tropopause altitude between the tropics and extratropics). Similarities and differences are found amongst the reanalyses, with some degree of tropical narrowing in the Eastern Pacific between 1981 and 2010. Historical simulations from the CMIP5 models agree well with the tropopause break latitudes depicted by the reanalyses, with considerable differences in estimated trends over the relatively short overlapping time period of the datasets. For future projections under the RCP8.5 scenario from 2006 to 2100, CMIP5 models generally show statistically significant increases in tropical width (at the 99% level) throughout each hemisphere, with regional variability of 1-2 degrees in poleward latitude trends. The impact of CMIP5 model grid resolution and other factors on the results of the tropopause break analysis will be discussed.

White Dwarf Rotation as a Function of Mass and a Dichotomy of Mode Line Widths: Kepler Observations of 27 Pulsating DA White Dwarfs through K2 Campaign 8

NASA Astrophysics Data System (ADS)

Hermes, J. J.; Gänsicke, B. T.; Kawaler, Steven D.; Greiss, S.; Tremblay, P.-E.; Gentile Fusillo, N. P.; Raddi, R.; Fanale, S. M.; Bell, Keaton J.; Dennihy, E.; Fuchs, J. T.; Dunlap, B. H.; Clemens, J. C.; Montgomery, M. H.; Winget, D. E.; Chote, P.; Marsh, T. R.; Redfield, S.

2017-10-01

We present photometry and spectroscopy for 27 pulsating hydrogen-atmosphere white dwarfs (DAVs; a.k.a. ZZ Ceti stars) observed by the Kepler space telescope up to K2 Campaign 8, an extensive compilation of observations with unprecedented duration (>75 days) and duty cycle (>90%). The space-based photometry reveals pulsation properties previously inaccessible to ground-based observations. We observe a sharp dichotomy in oscillation mode line widths at roughly 800 s, such that white dwarf pulsations with periods exceeding 800 s have substantially broader mode line widths, more reminiscent of a damped harmonic oscillator than a heat-driven pulsator. Extended Kepler coverage also permits extensive mode identification: we identify the spherical degree of 87 out of 201 unique radial orders, providing direct constraints of the rotation period for 20 of these 27 DAVs, more than doubling the number of white dwarfs with rotation periods determined via asteroseismology. We also obtain spectroscopy from 4 m-class telescopes for all DAVs with Kepler photometry. Using these homogeneously analyzed spectra, we estimate the overall mass of all 27 DAVs, which allows us to measure white dwarf rotation as a function of mass, constraining the endpoints of angular momentum in low- and intermediate-mass stars. We find that 0.51-0.73 M ⊙ white dwarfs, which evolved from 1.7-3.0 M ⊙ ZAMS progenitors, have a mean rotation period of 35 hr with a standard deviation of 28 hr, with notable exceptions for higher-mass white dwarfs. Finally, we announce an online repository for our Kepler data and follow-up spectroscopy, which we collect at http://k2wd.org.

White Dwarf Rotation as a Function of Mass and a Dichotomy of Mode Line Widths: Kepler  Observations of 27 Pulsating DA White Dwarfs through K2 Campaign 8

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hermes, J. J.; Fanale, S. M.; Dennihy, E.

We present photometry and spectroscopy for 27 pulsating hydrogen-atmosphere white dwarfs (DAVs; a.k.a. ZZ Ceti stars) observed by the Kepler space telescope up to K2 Campaign 8, an extensive compilation of observations with unprecedented duration (>75 days) and duty cycle (>90%). The space-based photometry reveals pulsation properties previously inaccessible to ground-based observations. We observe a sharp dichotomy in oscillation mode line widths at roughly 800 s, such that white dwarf pulsations with periods exceeding 800 s have substantially broader mode line widths, more reminiscent of a damped harmonic oscillator than a heat-driven pulsator. Extended Kepler coverage also permits extensive modemore » identification: we identify the spherical degree of 87 out of 201 unique radial orders, providing direct constraints of the rotation period for 20 of these 27 DAVs, more than doubling the number of white dwarfs with rotation periods determined via asteroseismology. We also obtain spectroscopy from 4 m-class telescopes for all DAVs with Kepler photometry. Using these homogeneously analyzed spectra, we estimate the overall mass of all 27 DAVs, which allows us to measure white dwarf rotation as a function of mass, constraining the endpoints of angular momentum in low- and intermediate-mass stars. We find that 0.51–0.73 M {sub ⊙} white dwarfs, which evolved from 1.7–3.0 M {sub ⊙} ZAMS progenitors, have a mean rotation period of 35 hr with a standard deviation of 28 hr, with notable exceptions for higher-mass white dwarfs. Finally, we announce an online repository for our Kepler data and follow-up spectroscopy, which we collect at http://k2wd.org.« less

How Weight Affects the Perceived Spacing between the Thumb and Fingers during Grasping

PubMed Central

Butler, Annie A.; Héroux, Martin E.; Gandevia, Simon C.

2015-01-01

We know much about mechanisms determining the perceived size and weight of lifted objects, but little about how these properties of size and weight affect the body representation (e.g. grasp aperture of the hand). Without vision, subjects (n = 16) estimated spacing between fingers and thumb (perceived grasp aperture) while lifting canisters of the same width (6.6cm) but varied weights (300, 600, 900, and 1200 g). Lifts were performed by movement of either the wrist, elbow or shoulder to examine whether lifting with different muscle groups affects the judgement of grasp aperture. Results for perceived grasp aperture were compared with changes in perceived weight of objects of different sizes (5.2, 6.6, and 10 cm) but the same weight (600 g). When canisters of the same width but different weights were lifted, perceived grasp aperture decreased 4.8% [2.2 ‒ 7.4] (mean [95% CI]; P < 0.001) from the lightest to the heaviest canister, no matter how they were lifted. For objects of the same weight but different widths, perceived weight decreased 42.3% [38.2 ‒ 46.4] from narrowest to widest (P < 0.001), as expected from the size-weight illusion. Thus, despite a highly distorted perception of the weight of objects based on their size, we conclude that proprioceptive afferents maintain a reasonably stable perception of the aperture of the grasping hand over a wide range of object weights. Given the small magnitude of this ‘weight-grasp aperture’ illusion, we propose the brain has access to a relatively stable ‘perceptual ruler’ to aid the manipulation of different objects. PMID:25996760

Insights into quasar UV spectra using unsupervised clustering analysis

NASA Astrophysics Data System (ADS)

Tammour, A.; Gallagher, S. C.; Daley, M.; Richards, G. T.

2016-06-01

Machine learning techniques can provide powerful tools to detect patterns in multidimensional parameter space. We use K-means - a simple yet powerful unsupervised clustering algorithm which picks out structure in unlabelled data - to study a sample of quasar UV spectra from the Quasar Catalog of the 10th Data Release of the Sloan Digital Sky Survey (SDSS-DR10) of Paris et al. Detecting patterns in large data sets helps us gain insights into the physical conditions and processes giving rise to the observed properties of quasars. We use K-means to find clusters in the parameter space of the equivalent width (EW), the blue- and red-half-width at half-maximum (HWHM) of the Mg II 2800 Å line, the C IV 1549 Å line, and the C III] 1908 Å blend in samples of broad absorption line (BAL) and non-BAL quasars at redshift 1.6-2.1. Using this method, we successfully recover correlations well-known in the UV regime such as the anti-correlation between the EW and blueshift of the C IV emission line and the shape of the ionizing spectra energy distribution (SED) probed by the strength of He II and the Si III]/C III] ratio. We find this to be particularly evident when the properties of C III] are used to find the clusters, while those of Mg II proved to be less strongly correlated with the properties of the other lines in the spectra such as the width of C IV or the Si III]/C III] ratio. We conclude that unsupervised clustering methods (such as K-means) are powerful methods for finding `natural' binning boundaries in multidimensional data sets and discuss caveats and future work.

Eicosapentaenoic acid reduces membrane fluidity, inhibits cholesterol domain formation, and normalizes bilayer width in atherosclerotic-like model membranes.

PubMed

Mason, R Preston; Jacob, Robert F; Shrivastava, Sandeep; Sherratt, Samuel C R; Chattopadhyay, Amitabha

2016-12-01

Cholesterol crystalline domains characterize atherosclerotic membranes, altering vascular signaling and function. Omega-3 fatty acids reduce membrane lipid peroxidation and subsequent cholesterol domain formation. We evaluated non-peroxidation-mediated effects of eicosapentaenoic acid (EPA), other TG-lowering agents, docosahexaenoic acid (DHA), and other long-chain fatty acids on membrane fluidity, bilayer width, and cholesterol domain formation in model membranes. In membranes prepared at 1.5:1 cholesterol-to-phospholipid (C/P) mole ratio (creating pre-existing domains), EPA, glycyrrhizin, arachidonic acid, and alpha linolenic acid promoted the greatest reductions in cholesterol domains (by 65.5%, 54.9%, 46.8%, and 45.2%, respectively) compared to controls; other treatments had modest effects. EPA effects on cholesterol domain formation were dose-dependent. In membranes with 1:1 C/P (predisposing domain formation), DHA, but not EPA, dose-dependently increased membrane fluidity. DHA also induced cholesterol domain formation without affecting temperature-induced changes in-bilayer unit cell periodicity relative to controls (d-space; 57Å-55Å over 15-30°C). Together, these data suggest simultaneous formation of distinct cholesterol-rich ordered domains and cholesterol-poor disordered domains in the presence of DHA. By contrast, EPA had no effect on cholesterol domain formation and produced larger d-space values relative to controls (60Å-57Å; p<0.05) over the same temperature range, suggesting a more uniform maintenance of lipid dynamics despite the presence of cholesterol. These data indicate that EPA and DHA had different effects on membrane bilayer width, membrane fluidity, and cholesterol crystalline domain formation; suggesting omega-3 fatty acids with differing chain length or unsaturation may differentially influence membrane lipid dynamics and structural organization as a result of distinct phospholipid/sterol interactions. Copyright © 2016. Published by Elsevier B.V.

Current forgings and their properties for steam generator of nuclear plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tsukada, Hisashi; Suzuki, Komei; Kusuhashi, Mikio

1997-12-31

Current steel forgings for steam generator (SG) of PWR plant are reviewed in the aspect of design and material improvement. The following three items are introduced. The use of integral type steel forgings for the fabrication of steam generator enhances the structural integrity and makes easier fabrication and inspection including in-service inspection. The following examples of current integral type forgings developed by the Japan Steel Works, Ltd. (JSW) are introduced: (1) primary head integrated with nozzles, manways and supports; (2) steam drum head integrated with nozzle and handhole; (3) conical shell integrated with cylindrical sections and handholes. In order tomore » decrease the weight of steam generator, the high strength materials such as SA508, Cl.3a steel have been adopted in some cases. The properties of this steel are introduced and the chemistry and heat treatment condition are discussed. As one of the methods to minimize the macro- and micro-segregations, the use of vacuum carbon deoxidation (VCD), i.e. deoxidization of steel by gaseous CO reaction, with addition of Al for grain refining was investigated. The properties of SA508, Cl.3 steels with Low Si content are compared with those of conventional one.« less

AdS and stabilized extra dimensions in multi-dimensional gravitational models with nonlinear scalar curvature terms R-1 and R4

NASA Astrophysics Data System (ADS)

Günther, Uwe; Zhuk, Alexander; Bezerra, Valdir B.; Romero, Carlos

2005-08-01

We study multi-dimensional gravitational models with scalar curvature nonlinearities of types R-1 and R4. It is assumed that the corresponding higher dimensional spacetime manifolds undergo a spontaneous compactification to manifolds with a warped product structure. Special attention has been paid to the stability of the extra-dimensional factor spaces. It is shown that for certain parameter regions the systems allow for a freezing stabilization of these spaces. In particular, we find for the R-1 model that configurations with stabilized extra dimensions do not provide a late-time acceleration (they are AdS), whereas the solution branch which allows for accelerated expansion (the dS branch) is incompatible with stabilized factor spaces. In the case of the R4 model, we obtain that the stability region in parameter space depends on the total dimension D = dim(M) of the higher dimensional spacetime M. For D > 8 the stability region consists of a single (absolutely stable) sector which is shielded from a conformal singularity (and an antigravity sector beyond it) by a potential barrier of infinite height and width. This sector is smoothly connected with the stability region of a curvature-linear model. For D < 8 an additional (metastable) sector exists which is separated from the conformal singularity by a potential barrier of finite height and width so that systems in this sector are prone to collapse into the conformal singularity. This second sector is not smoothly connected with the first (absolutely stable) one. Several limiting cases and the possibility of inflation are discussed for the R4 model.

Histological and histomorphometrical evaluation of furcation perforations filled with MTA, CPM and ZOE.

PubMed

da Silva, G F; Guerreiro-Tanomaru, J M; Sasso-Cerri, E; Tanomaru-Filho, M; Cerri, P S

2011-02-01

To evaluate the biological response of the periodontium adjacent to furcation perforations in rat molars filled with Endo-CPM-Sealer (CPM), MTA-Angelus (MTA) or zinc oxide-eugenol cement (ZOE). The pulp chamber floors of maxillary right first molar teeth were perforated and sealed with CPM, mineral trioxide aggregate (MTA) or ZOE; the left first molars, without any treatment, were used as controls (CG). After 7, 15, 30 and 60 days, fragments of maxilla were fixed, decalcified and embedded in paraffin. Sections were stained with H&E, Masson's trichrome and submitted to tartrate-resistant acid phosphatase (TRAP) reaction, used as an osteoclast marker. The width of the periodontal space, the numerical density of inflammatory cells and the number of TRAP-positive osteoclasts in the bone surface were measured, and statistical analyses were performed using analysis of variance and Tukey test (P ≤ 0.05). In all experimental groups, the greatest number of inflammatory cells was observed at 7 days, especially in the ZOE group. In this group, the intense inflammatory process was related to a significant increase (P ≤ 0.05) in the number of osteoclasts and, thereby, in an increase in the width of the periodontal space. At 60 days, no significant differences in osteoclast numbers amongst CPM, MTA and CG groups occurred; the periodontal space was also significantly reduced in the experimental groups in comparison with the initial periods. However, in the ZOE group, the periodontal space was significantly larger (P ≤ 0.05) in comparison with MTA-based materials. The periodontium adjacent to perforations filled with MTA and CPM exhibited clear evidence of re-establishment and thus better biocompatibility than ZOE. © 2010 International Endodontic Journal.

A novel weld seam detection method for space weld seam of narrow butt joint in laser welding

NASA Astrophysics Data System (ADS)

Shao, Wen Jun; Huang, Yu; Zhang, Yong

2018-02-01

Structured light measurement is widely used for weld seam detection owing to its high measurement precision and robust. However, there is nearly no geometrical deformation of the stripe projected onto weld face, whose seam width is less than 0.1 mm and without misalignment. So, it's very difficult to ensure an exact retrieval of the seam feature. This issue is raised as laser welding for butt joint of thin metal plate is widely applied. Moreover, measurement for the seam width, seam center and the normal vector of the weld face at the same time during welding process is of great importance to the welding quality but rarely reported. Consequently, a seam measurement method based on vision sensor for space weld seam of narrow butt joint is proposed in this article. Three laser stripes with different wave length are project on the weldment, in which two red laser stripes are designed and used to measure the three dimensional profile of the weld face by the principle of optical triangulation, and the third green laser stripe is used as light source to measure the edge and the centerline of the seam by the principle of passive vision sensor. The corresponding image process algorithm is proposed to extract the centerline of the red laser stripes as well as the seam feature. All these three laser stripes are captured and processed in a single image so that the three dimensional position of the space weld seam can be obtained simultaneously. Finally, the result of experiment reveals that the proposed method can meet the precision demand of space narrow butt joint.

Beam width and transmitter power adaptive to tracking system performance for free-space optical communication.

PubMed

Arnon, S; Rotman, S; Kopeika, N S

1997-08-20

The basic free-space optical communication system includes at least two satellites. To communicate between them, the transmitter satellite must track the beacon of the receiver satellite and point the information optical beam in its direction. Optical tracking and pointing systems for free space suffer during tracking from high-amplitude vibration because of background radiation from interstellar objects such as the Sun, Moon, Earth, and stars in the tracking field of view or the mechanical impact from satellite internal and external sources. The vibrations of beam pointing increase the bit error rate and jam communication between the two satellites. One way to overcome this problem is to increase the satellite receiver beacon power. However, this solution requires increased power consumption and weight, both of which are disadvantageous in satellite development. Considering these facts, we derive a mathematical model of a communication system that adapts optimally the transmitter beam width and the transmitted power to the tracking system performance. Based on this model, we investigate the performance of a communication system with discrete element optical phased array transmitter telescope gain. An example for a practical communication system between a Low Earth Orbit Satellite and a Geostationary Earth Orbit Satellite is presented. From the results of this research it can be seen that a four-element adaptive transmitter telescope is sufficient to compensate for vibration amplitude doubling. The benefits of the proposed model are less required transmitter power and improved communication system performance.

Sediment dynamics of a high gradient stream in the Oi river basin of Japan

Treesearch

Hideji Maita

1991-01-01

This paper discusses the effects of the valley width for discontinuities of sediment transport in natural stream channels. The results may be summarized as follows: 1)ln torrential rivers. deposition or erosion depend mostly on the sediment supply. not on the magnitude of the flow discharge. 2)Wide valley floors of streams are depositional spaces where the excess...

Two-dimensional free-space beam steering with an optical phased array on silicon-on-insulator.

PubMed

Doylend, J K; Heck, M J R; Bovington, J T; Peters, J D; Coldren, L A; Bowers, J E

2011-10-24

We demonstrate a 16-channel, independently tuned waveguide surface grating optical phased array in silicon for two dimensional beam steering with a total field of view of 20° x 14°, beam width of 0.6° x 1.6°, and full-window background peak suppression of 10 dB. © 2011 Optical Society of America

Design rules for RCA self-aligned silicon-gate CMOS/SOS process

NASA Technical Reports Server (NTRS)

1977-01-01

The CMOS/SOS design rules prepared by the RCA Solid State Technology Center (SSTC) are described. These rules specify the spacing and width requirements for each of the six design levels, the seventh level being used to define openings in the passivation level. An associated report, entitled Silicon-Gate CMOS/SOS Processing, provides further insight into the usage of these rules.

Erratum: Erratum to Central European Journal of Engineering, Volume 4, Issue 1

NASA Astrophysics Data System (ADS)

Kumar, M. Ajay; Srikanth, N. V.

2014-06-01

Paper by M. Ajay Kumar, N. V. Srikanth, et al. "An adaptive neuro fuzzy inference system controlled space cector pulse width modulation based HVDC light transmission system under AC fault conditions" in Volume 4, Issue 1, 27-38/March 2014 doi: 10.2478/s13531-013-0143-4 contains an error in the title. The correct title is presented below

Quantifying Proxy Influence in the Last Millennium Reanalysis

NASA Astrophysics Data System (ADS)

Hakim, G. J.; Anderson, D. N.; Emile-Geay, J.; Noone, D.; Tardif, R.

2017-12-01

We examine the influence of proxies in the climate field reconstruction known as the Last Millennium Reanalysis (Hakim et al. 2016; JGR-A). This data assimilation framework uses the CCSM4 Last Millennium simulation as an agnostic prior, proxies from the PAGES 2k Consortium (2017; Sci. Data), and an offline ensemble square-root filter for assimilation. Proxies are forward modeled using an observation model ("proxy system model") that maps from the prior space to the proxy space. We assess proxy impact using the method of Cardinali et al. (2004; QJRMS), where influence is measured in observation space; that is, at the location of observations. Influence is determined by three components: the prior at the location, the proxy at the location, and remote proxies as mediated by the spatial covariance information in the prior. Consequently, on a per-proxy basis, influence is higher for spatially isolated proxies having small error, and influence is lower for spatially dense proxies having large error. Results show that proxy influence depends strongly on the observation model. Assuming the proxies depend linearly on annual mean temperature yields the largest per-proxy influence for coral d18O and coral Sr/Ca records, and smallest influence for tree-ring width. On a global basis (summing over all proxies of a given type), tree-ring width and coral d18O have the largest influence. A seasonal model for the proxies yields very different results. In this case we model the proxies linearly on objectively determined seasonal temperature, except for tree proxies, which are fit to a bivariate model on seasonal temperature and precipitation. In this experiment, on a per-proxy basis, tree-ring density has by far the greatest influence. Total proxy influence is dominated by tree-ring width followed by tree-ring density. Compared to the results for the annual-mean observation model, the experiment where proxies are measured seasonally has more than double the total influence (sum over all proxies); this experiment also has higher verification scores when measured against other 20th century temperature reconstructions. These results underscore the importance of improving proxy system models, since they increase the amount of information available for data-assimilation-based reconstructions.

Extending the Calibration of C IV-based Single-epoch Black Hole Mass Estimators for Active Galactic Nuclei

NASA Astrophysics Data System (ADS)

Park, Daeseong; Barth, Aaron J.; Woo, Jong-Hak; Malkan, Matthew A.; Treu, Tommaso; Bennert, Vardha N.; Assef, Roberto J.; Pancoast, Anna

2017-04-01

We provide an updated calibration of C IV λ 1549 broad emission line–based single-epoch (SE) black hole (BH) mass estimators for active galactic nuclei (AGNs) using new data for six reverberation-mapped AGNs at redshift z=0.005{--}0.028 with BH masses (bolometric luminosities) in the range {10}6.5{--}{10}7.5 {M}ȯ ({10}41.7{--}{10}43.8 erg s‑1). New rest-frame UV-to-optical spectra covering 1150–5700 Å for the six AGNs were obtained with the Hubble Space Telescope (HST). Multicomponent spectral decompositions of the HST spectra were used to measure SE emission-line widths for the C IV, Mg II, and Hβ lines, as well as continuum luminosities in the spectral region around each line. We combine the new data with similar measurements for a previous archival sample of 25 AGNs to derive the most consistent and accurate calibrations of the C IV-based SE BH mass estimators against the Hβ reverberation-based masses, using three different measures of broad-line width: full width at half maximum (FWHM), line dispersion ({σ }line}), and mean absolute deviation (MAD). The newly expanded sample at redshift z=0.005{--}0.234 covers a dynamic range in BH mass (bolometric luminosity) of {log}{M}BH}/{M}ȯ =6.5{--}9.1 ({log}{L}bol}/ erg s‑1 = 41.7{--}46.9), and we derive the new C IV-based mass estimators using a Bayesian linear regression analysis over this range. We generally recommend the use of {σ }line} or MAD rather than FWHM to obtain a less biased velocity measurement of the C IV emission line, because its narrow-line component contribution is difficult to decompose from the broad-line profile. Based on observations made with the NASA/ESA Hubble Space Telescope, obtained at the Space Telescope Science Institute, which is operated by the Association of Universities for Research in Astronomy, Inc., under NASA contract NAS 5-26555. These observations are associated with program GO-12922.

Toroidal Alfvén eigenmode triggered by trapped anisotropic energetic particles in a toroidal resistive plasma with free boundary

NASA Astrophysics Data System (ADS)

Yang, S. X.; Hao, G. Z.; Liu, Y. Q.; Wang, Z. X.; Hu, Y. J.; Zhu, J. X.; He, H. D.; Wang, A. K.

2018-04-01

The toroidal Alfvén eigenmode (TAE), excited by trapped energetic particles (EPs), is numerically investigated in a tokamak plasma, using the non-perturbative magnetohydrodynamic-kinetic hybrid formulation based MARS-K code (Liu et al 2008 Phys. Plasmas 15 112503). Compared with the fixed boundary condition at the plasma edge, a free boundary enhances the critical value of the EPs kinetic contribution for driving the TAE. Free boundary also induces finite perturbations at the plasma edge as expected. An anisotropic distribution of EPs, in the particle pitch angle space, strongly enhances the instability and results in a more global mode structure, compared with the isotropic case. The plasma resistivity is also found to play a role in the EPs-destabilized TAE. In particular, the mode stability domain is mapped out, in the 2D parameter space of the plasma resistivity and a quantity defining the width of the particle distribution in pitch angle (for anisotropic distribution). A resonance layer in the poloidal mode structure, with the layer width increasing with the plasma resistivity, appears at the large width of the particle distribution in pitch angle space. A mode conversion, from the modified ideal kink by the EPs kinetic effect to the TAE, is also observed while increasing the birth energy of EPs. Computational results suggest that the TAE mode structure can be modified by certain key plasma parameters, such as the EPs kinetic contribution, the equilibrium pressure, the plasma resistivity, the distribution of EPs, as well as the birth energy of EPs. Such modification of the eigenmode structure can only be obtained following the non-perturbative hybrid approach (Wang et al 2013 Phys. Rev. Lett. 111 145003, Wang et al 2015 Phys. Plasmas 22 022509), as adopted in this study. More importantly, numerical results show that near the marginal stability point, the dominant poloidal harmonics of the TAE overlap with each other, and are localized at the tip positions of the Alfvén continua. This kind of TAE structure in high beta plasma with unstable ideal kink is substantially different from that of the conventional TAE.

3D-HST Grism Spectroscopy of a Gravitationally Lensed, Low-metallicity Starburst Galaxy at z = 1.847

NASA Astrophysics Data System (ADS)

Brammer, Gabriel B.; Sánchez-Janssen, Rubén; Labbé, Ivo; da Cunha, Elisabete; Erb, Dawn K.; Franx, Marijn; Fumagalli, Mattia; Lundgren, Britt; Marchesini, Danilo; Momcheva, Ivelina; Nelson, Erica; Patel, Shannon; Quadri, Ryan; Rix, Hans-Walter; Skelton, Rosalind E.; Schmidt, Kasper B.; van der Wel, Arjen; van Dokkum, Pieter G.; Wake, David A.; Whitaker, Katherine E.

2012-10-01

We present Hubble Space Telescope (HST) imaging and spectroscopy of the gravitational lens SL2SJ02176-0513, a cusp arc at z = 1.847. The UV continuum of the lensed galaxy is very blue, which is seemingly at odds with its redder optical colors. The 3D-HST WFC3/G141 near-infrared spectrum of the lens reveals the source of this discrepancy to be extremely strong [O III] λ5007 and Hβ emission lines with rest-frame equivalent widths of 2000 ± 100 and 520 ± 40 Å, respectively. The source has a stellar mass ~108 M ⊙, sSFR ~ 100 Gyr-1, and detection of [O III] λ4363 yields a metallicity of 12 + log (O/H) = 7.5 ± 0.2. We identify local blue compact dwarf analogs to SL2SJ02176-0513, which are among the most metal-poor galaxies in the Sloan Digital Sky Survey. The local analogs resemble the lensed galaxy in many ways, including UV/optical spectral energy distribution, spatial morphology, and emission line equivalent widths and ratios. Common to SL2SJ02176-0513 and its local counterparts is an upturn at mid-IR wavelengths likely arising from hot dust heated by starbursts. The emission lines of SL2SJ02176-0513 are spatially resolved owing to the combination of the lens and the high spatial resolution of HST. The lensed galaxy is composed of two clumps with combined size re ~300 pc, and we resolve significant differences in UV color and emission line equivalent width between them. Though it has characteristics occasionally attributed to active galactic nuclei, we conclude that SL2SJ02176-0513 is a low-metallicity star-bursting dwarf galaxy. Such galaxies will be found in significant numbers in the full 3D-HST grism survey. Based on observations made with the NASA/ESA Hubble Space Telescope, program 12328, obtained at the Space Telescope Science Institute, which is operated by the Association of Universities for Research in Astronomy, Inc., under NASA contract NAS 5-26555.

Airborne multispectral detection of regrowth cotton fields

NASA Astrophysics Data System (ADS)

Westbrook, John K.; Suh, Charles P.-C.; Yang, Chenghai; Lan, Yubin; Eyster, Ritchie S.

2015-01-01

Effective methods are needed for timely areawide detection of regrowth cotton plants because boll weevils (a quarantine pest) can feed and reproduce on these plants beyond the cotton production season. Airborne multispectral images of regrowth cotton plots were acquired on several dates after three shredding (i.e., stalk destruction) dates. Linear spectral unmixing (LSU) classification was applied to high-resolution airborne multispectral images of regrowth cotton plots to estimate the minimum detectable size and subsequent growth of plants. We found that regrowth cotton fields can be identified when the mean plant width is ˜0.2 m for an image resolution of 0.1 m. LSU estimates of canopy cover of regrowth cotton plots correlated well (r2=0.81) with the ratio of mean plant width to row spacing, a surrogate measure of plant canopy cover. The height and width of regrowth plants were both well correlated (r2=0.94) with accumulated degree-days after shredding. The results will help boll weevil eradication program managers use airborne multispectral images to detect and monitor the regrowth of cotton plants after stalk destruction, and identify fields that may require further inspection and mitigation of boll weevil infestations.

High-order nonuniformly correlated beams

NASA Astrophysics Data System (ADS)

Wu, Dan; Wang, Fei; Cai, Yangjian

2018-02-01

We have introduced a class of partially coherent beams with spatially varying correlations named high-order nonuniformly correlated (HNUC) beams, as an extension of conventional nonuniformly correlated (NUC) beams. Such beams bring a new parameter (mode order) which is used to tailor the spatial coherence properties. The behavior of the spectral density of the HNUC beams on propagation has been investigated through numerical examples with the help of discrete model decomposition and fast Fourier transform (FFT) algorithm. Our results reveal that by selecting the mode order appropriately, the more sharpened intensity maxima can be achieved at a certain propagation distance compared to that of the NUC beams, and the lateral shift of the intensity maxima on propagation is closed related to the mode order. Furthermore, analytical expressions for the r.m.s width and the propagation factor of the HNUC beams on free-space propagation are derived by means of Wigner distribution function. The influence of initial beam parameters on the evolution of the r.m.s width and the propagation factor, and the relation between the r.m.s width and the occurring of the sharpened intensity maxima on propagation have been studied and discussed in detail.

Doppler lidar signal and turbulence study

NASA Technical Reports Server (NTRS)

Frost, W.; Huang, K. H.; Fitzjarrald, D. F.

1983-01-01

Comparison of the second moments of the Doppler lidar signal with aircraft and tower measured parameters is being carried out. Lidar binary data tapes were successfully converted to ASCII Code on the VAX 11/780. These data were used to develop the computer programs for analyzing data from the Marshall Space Flight Center field test. Raw lidar amplitude along the first 50 forward and backward beams of Run No. 2, respectively was plotted. Plotting techniques for the same beams except with the amplitude thresholded and range corrected were developed. Plotting routines for the corresponding lidar width of the first 50 forward and backward beams were also established. The relationship between raw lidar amplitude and lidar width was examined. The lidar width is roughly constant for lidar amplitudes less than 120 dB. A field test with the NASA/MSFC ground based Doppler lidar, the instrumented NASA B-57B gust gradient aircraft, and the NASA/MSFC eight tower array was carried out. The data tape for the lidar was received and read. The aircraft data and tower data are being digitized and converted to engineering units. Velocities computed sequentially along each of the lidar beams beginning at 16:40:00, May 12, 1983 were plotted for Run No. 1.

Propagation factors of multi-sinc Schell-model beams in non-Kolmogorov turbulence.

PubMed

Song, Zhenzhen; Liu, Zhengjun; Zhou, Keya; Sun, Qiongge; Liu, Shutian

2016-01-25

We derive several analytical expressions for the root-mean-square (rms) angular width and the M(2)-factor of the multi-sinc Schell-model (MSSM) beams propagating in non-Kolmogorov turbulence with the extended Huygens-Fresnel principle and the second-order moments of the Wigner distribution function. Numerical results show that a MSSM beam with dark-hollow far fields in free space has advantage over the one with flat-topped or multi-rings far fields for reducing the turbulence-induced degradation, which will become more obvious with larger dark-hollow size. Beam quality of MSSM beams can be further improved with longer wavelength and larger beam width, or under the condition of weaker turbulence. We also demonstrate that the non-Kolmogorov turbulence has significantly less effect on the MSSM beams than the Gaussian Schell-model beam.

Local divergence and curvature divergence in first order optics

NASA Astrophysics Data System (ADS)

Mafusire, Cosmas; Krüger, Tjaart P. J.

2018-06-01

The far-field divergence of a light beam propagating through a first order optical system is presented as a square root of the sum of the squares of the local divergence and the curvature divergence. The local divergence is defined as the ratio of the beam parameter product to the beam width whilst the curvature divergence is a ratio of the space-angular moment also to the beam width. It is established that the beam’s focusing parameter can be defined as a ratio of the local divergence to the curvature divergence. The relationships between the two divergences and other second moment-based beam parameters are presented. Their various mathematical properties are presented such as their evolution through first order systems. The efficacy of the model in the analysis of high power continuous wave laser-based welding systems is briefly discussed.

Isolated post resonator mesogyroscope

NASA Technical Reports Server (NTRS)

Challoner, Dorian; Peay, Chris; Wellman, Joanne; Shcheglov, Kirill; Hayworth, Ken; Wiberg, Dean; Yee, Karl; Sipppola, Clayton

2004-01-01

A new symmetric vibratory gyroscope principle has been devised in which a central post proof mass is counter-rocked against an outer sensing plate such that the motion is isolated from the gyroscope case. Prototype gyroscopes have been designed and fabricated with micromachined silicon at mesoscale (20-cm resonator width), vs. microscale (e.g., 2-mm resonator width) to achieve higher sensitivity and machined precision. This novel mesogyro design arose out of an ongoing technical cooperation between JPL and Boeing begun in 1997 to advance the design of micro-inertial sensors for low-cost space applications. This paper describes the theory of operation of the mesogyro and relationships with other vibratory gyroscopes, the mechanical design, closed loop electronics design, bulk silicon fabrication and packaged gyroscope assembly and test methods. The initial packaged prototype test results are reported for what is believed to be the first silicon mesogyroscope.

A search strategy for SETI - The search for extraterrestrial intelligence

NASA Technical Reports Server (NTRS)

Billingham, J.; Wolfe, J.; Edelson, R.; Gulkis, S.; Olsen, E.; Oliver, B.; Tarter, J.; Seeger, C.

1980-01-01

A search strategy is proposed for the detection of signals of extraterrestrial intelligent origin. It constitutes an exploration of a well defined volume of search space in the microwave region of the spectrum and envisages the use of a combination of sky survey and targeted star approaches. It is predicated on the use of existing antennas equipped with sophisticated multichannel spectrum analyzers and signal processing systems operating in the digital mode. The entire sky would be surveyed between 1 and 10 GHz with resolution bin widths down to 32 Hz. More than 700 nearby solar type stars and other selected interesting directions would be searched between 1 GHz and 3 GHz with bin widths down to 1 Hz. Particular emphasis would be placed on those solar type stars that are within 20 light years of earth.

The sonar aperture and its neural representation in bats.

PubMed

Heinrich, Melina; Warmbold, Alexander; Hoffmann, Susanne; Firzlaff, Uwe; Wiegrebe, Lutz

2011-10-26

As opposed to visual imaging, biosonar imaging of spatial object properties represents a challenge for the auditory system because its sensory epithelium is not arranged along space axes. For echolocating bats, object width is encoded by the amplitude of its echo (echo intensity) but also by the naturally covarying spread of angles of incidence from which the echoes impinge on the bat's ears (sonar aperture). It is unclear whether bats use the echo intensity and/or the sonar aperture to estimate an object's width. We addressed this question in a combined psychophysical and electrophysiological approach. In three virtual-object playback experiments, bats of the species Phyllostomus discolor had to discriminate simple reflections of their own echolocation calls differing in echo intensity, sonar aperture, or both. Discrimination performance for objects with physically correct covariation of sonar aperture and echo intensity ("object width") did not differ from discrimination performances when only the sonar aperture was varied. Thus, the bats were able to detect changes in object width in the absence of intensity cues. The psychophysical results are reflected in the responses of a population of units in the auditory midbrain and cortex that responded strongest to echoes from objects with a specific sonar aperture, regardless of variations in echo intensity. Neurometric functions obtained from cortical units encoding the sonar aperture are sufficient to explain the behavioral performance of the bats. These current data show that the sonar aperture is a behaviorally relevant and reliably encoded cue for object size in bat sonar.

Effect of semi-rapid maxillary expansion in children with obstructive sleep apnea syndrome: 5-month follow-up study.

PubMed

Hoxha, Saimir; Kaya-Sezginer, Ecem; Bakar-Ates, Filiz; Köktürk, Oğuz; Toygar-Memikoğlu, Ufuk

2018-02-17

The purpose of this study was to investigate the effect of semi-rapid maxillary expansion (SRME) orthodontic treatment on biomarkers and respiratory parameters in children with obstructive sleep apnea syndrome (OSAS) and maxillary transverse deficiency. Thirty children with OSAS were included in this study. Fifteen children were enrolled as control, and 15 children were subjected to SRME orthodontic treatment method for 5 months. Beside respiratory parameters, pharyngeal area, dental arch, and postero-anterior widths and the levels of OSAS biomarkers in serum and urine were measured. Pharyngeal airway space, dental arch, and postero-anterior widths were increased after SRME treatment. Sleep tests showed a decrease in the apnea-hypopnea index (AHI) after 5-month control/treatment duration. Serum kallikrein (KLK)1 levels decreased significantly in the treatment group. There was a significant increase in serum orosomucoid (ORM)2 levels and a decrease in urine perlecan levels in the control group after a 5-month follow-up. A significant negative correlation between serum ORM2, perlecan, gelsolin, and KLK1 levels and intercanin width, as well as between serum ORM2 and KLK1 levels and intermolar width, was observed. SRME treatment can be considered as a useful approach in children with OSAS. A further investigation of OSAS-related biomarkers and their relationship with sleep and orthodontic parameters is needed for providing easier and reliable modulatory strategies in the treatment of OSAS.

Expected Performance of the Upcoming Surface Water and Ocean Topography Mission Measurements of River Height, Width, and Slope

NASA Astrophysics Data System (ADS)

Wei, R.; Frasson, R. P. M.; Williams, B. A.; Rodriguez, E.; Pavelsky, T.; Altenau, E. H.; Durand, M. T.

2017-12-01

The upcoming Surface Water and Ocean Topography (SWOT) mission will measure river widths and water surface elevations of rivers wider than 100 m. In preparation for the SWOT mission, the Jet Propulsion Laboratory built the SWOT hydrology simulator with the intent of generating synthetic SWOT overpasses over rivers with realistic error characteristics. These synthetic overpasses can be used to guide the design of processing methods and data products, as well as develop data assimilation techniques that will incorporate the future SWOT data into hydraulic and hydrologic models as soon as the satellite becomes operational. SWOT simulator uses as inputs water depth, river bathymetry, and the surrounding terrain digital elevation model to create simulated interferograms of the study area. Next, the simulator emulates the anticipated processing of SWOT data by attempting to geolocate and classify the radar returns. The resulting cloud of points include information on water surface elevation, pixel area, and surface classification (land vs water). Finally, we process the pixel clouds by grouping pixels into equally spaced nodes located at the river centerline. This study applies the SWOT simulator to six different rivers: Sacramento River, Tanana River, Saint Lawrence River, Platte River, Po River, and Amazon River. This collection of rivers covers a range of size, slope, and planform complexity with the intent of evaluating the impact of river width, slope, planform complexity, and surrounding topography on the anticipated SWOT height, width, and slope error characteristics.

Vespertilionid bats control the width of their biosonar sound beam dynamically during prey pursuit

PubMed Central

Jakobsen, Lasse; Surlykke, Annemarie

2010-01-01

Animals using sound for communication emit directional signals, focusing most acoustic energy in one direction. Echolocating bats are listening for soft echoes from insects. Therefore, a directional biosonar sound beam greatly increases detection probability in the forward direction and decreases off-axis echoes. However, high directionality has context-specific disadvantages: at close range the detection space will be vastly reduced, making a broad beam favorable. Hence, a flexible system would be very advantageous. We investigated whether bats can dynamically change directionality of their biosonar during aerial pursuit of insects. We trained five Myotis daubentonii and one Eptesicus serotinus to capture tethered mealworms and recorded their echolocation signals with a multimicrophone array. The results show that the bats broaden the echolocation beam drastically in the terminal phase of prey pursuit. M. daubentonii increased the half-amplitude angle from approximately 40° to approximately 90° horizontally and from approximately 45° to more than 90° vertically. The increase in beam width is achieved by lowering the frequency by roughly one octave from approximately 55 kHz to approximately 27.5 kHz. The E. serotinus showed beam broadening remarkably similar to that of M. daubentonii. Our results demonstrate dynamic control of beam width in both species. Hence, we propose directionality as an explanation for the frequency decrease observed in the buzz of aerial hawking vespertilionid bats. We predict that future studies will reveal dynamic control of beam width in a broad range of acoustically communicating animals. PMID:20643943

Vespertilionid bats control the width of their biosonar sound beam dynamically during prey pursuit.

PubMed

Jakobsen, Lasse; Surlykke, Annemarie

2010-08-03

Animals using sound for communication emit directional signals, focusing most acoustic energy in one direction. Echolocating bats are listening for soft echoes from insects. Therefore, a directional biosonar sound beam greatly increases detection probability in the forward direction and decreases off-axis echoes. However, high directionality has context-specific disadvantages: at close range the detection space will be vastly reduced, making a broad beam favorable. Hence, a flexible system would be very advantageous. We investigated whether bats can dynamically change directionality of their biosonar during aerial pursuit of insects. We trained five Myotis daubentonii and one Eptesicus serotinus to capture tethered mealworms and recorded their echolocation signals with a multimicrophone array. The results show that the bats broaden the echolocation beam drastically in the terminal phase of prey pursuit. M. daubentonii increased the half-amplitude angle from approximately 40 degrees to approximately 90 degrees horizontally and from approximately 45 degrees to more than 90 degrees vertically. The increase in beam width is achieved by lowering the frequency by roughly one octave from approximately 55 kHz to approximately 27.5 kHz. The E. serotinus showed beam broadening remarkably similar to that of M. daubentonii. Our results demonstrate dynamic control of beam width in both species. Hence, we propose directionality as an explanation for the frequency decrease observed in the buzz of aerial hawking vespertilionid bats. We predict that future studies will reveal dynamic control of beam width in a broad range of acoustically communicating animals.

[The reliability of dento-maxillary models created by cone-beam CT and rapid prototyping:a comparative study].

PubMed

Lv, Yan; Yan, Bin; Wang, Lin; Lou, Dong-hua

2012-04-01

To analyze the reliability of the dento-maxillary models created by cone-beam CT and rapid prototyping (RP). Plaster models were obtained from 20 orthodontic patients who had been scanned by cone-beam CT and 3-D models were formed after the calculation and reconstruction of software. Then, computerized composite models (RP models) were produced by rapid prototyping technique. The crown widths, dental arch widths and dental arch lengths on each plaster model, 3-D model and RP model were measured, followed by statistical analysis with SPSS17.0 software package. For crown widths, dental arch lengths and crowding, there were significant differences(P<0.05) among the 3 models, but the dental arch widths were on the contrary. Measurements on 3-D models were significantly smaller than those on other two models(P<0.05). Compared with 3-D models, RP models had more numbers which were not significantly different from those on plaster models(P>0.05). The regression coefficient among three models were significantly different(P<0.01), ranging from 0.8 to 0.9. But between RP and plaster models was bigger than that between 3-D and plaster models. There is high consistency within 3 models, while some differences were accepted in clinic. Therefore, it is possible to substitute 3-D and RP models for plaster models in order to save storage space and improve efficiency.

Mathematical model of parking space unit for triangular parking area

NASA Astrophysics Data System (ADS)

Syahrini, Intan; Sundari, Teti; Iskandar, Taufiq; Halfiani, Vera; Munzir, Said; Ramli, Marwan

2018-01-01

Parking space unit (PSU) is an effective measure for the area size of a vehicle, including the free space and the width of the door opening of the vehicle (car). This article discusses a mathematical model for parking space of vehicles in triangular shape area. An optimization model for triangular parking lot is developed. Integer Linear Programming (ILP) method is used to determine the maximum number of the PSU. The triangular parking lot is in isosceles and equilateral triangles shape and implements four possible rows and five possible angles for each field. The vehicles which are considered are cars and motorcycles. The results show that the isosceles triangular parking area has 218 units of optimal PSU, which are 84 units of PSU for cars and 134 units of PSU for motorcycles. Equilateral triangular parking area has 688 units of optimal PSU, which are 175 units of PSU for cars and 513 units of PSU for motorcycles.

The cavity heat pipe Stirling receiver for space solar dynamics

NASA Technical Reports Server (NTRS)

Kesseli, James B.; Lacy, Dovie E.

1989-01-01

The receiver/storage unit for the low-earth-orbiting Stirling system is discussed. The design, referred to as the cavity heat pipe (CHP), has been optimized for minimum specific mass and volume width. A specific version of this design at the 7-kWe level has been compared to the space station Brayton solar dynamic design. The space station design utilizes a eutectic mixture of LiF and CaF2. Using the same phase change material, the CHP has been shown to have a specific mass of 40 percent and a volume of 5 percent of that of the space station Brayton at the same power level. Additionally, it complements the free-piston Stirling engine in that it also maintains a relatively flat specific mass down to at least 1 kWe. The technical requirements, tradeoff studies, critical issues, and critical technology experiments are discussed.

Electronics for Deep Space Cryogenic Applications

NASA Technical Reports Server (NTRS)

Patterson, R. L.; Hammond, A.; Dickman, J. E.; Gerber, S. S.; Elbuluk, M. E.; Overton, E.

2002-01-01

Deep space probes and planetary exploration missions require electrical power management and control systems that are capable of efficient and reliable operation in very cold temperature environments. Typically, in deep space probes, heating elements are used to keep the spacecraft electronics near room temperature. The utilization of power electronics designed for and operated at low temperature will contribute to increasing efficiency and improving reliability of space power systems. At NASA Glenn Research Center, commercial-off-the-shelf devices as well as developed components are being investigated for potential use at low temperatures. These devices include semiconductor switching devices, magnetics, and capacitors. Integrated circuits such as digital-to-analog and analog-to-digital converters, DC/DC converters, operational amplifiers, and oscillators are also being evaluated. In this paper, results will be presented for selected analog-to-digital converters, oscillators, DC/DC converters, and pulse width modulation (PWM) controllers.

High performance flight computer developed for deep space applications

NASA Technical Reports Server (NTRS)

Bunker, Robert L.

1993-01-01

The development of an advanced space flight computer for real time embedded deep space applications which embodies the lessons learned on Galileo and modern computer technology is described. The requirements are listed and the design implementation that meets those requirements is described. The development of SPACE-16 (Spaceborne Advanced Computing Engine) (where 16 designates the databus width) was initiated to support the MM2 (Marine Mark 2) project. The computer is based on a radiation hardened emulation of a modern 32 bit microprocessor and its family of support devices including a high performance floating point accelerator. Additional custom devices which include a coprocessor to improve input/output capabilities, a memory interface chip, and an additional support chip that provide management of all fault tolerant features, are described. Detailed supporting analyses and rationale which justifies specific design and architectural decisions are provided. The six chip types were designed and fabricated. Testing and evaluation of a brass/board was initiated.

Surface roughness measuring system. [synthetic aperture radar measurements of ocean wave height and terrain peaks

NASA Technical Reports Server (NTRS)

Jain, A. (Inventor)

1978-01-01

Significant height information of ocean waves, or peaks of rough terrain is obtained by compressing the radar signal over different widths of the available chirp or Doppler bandwidths, and cross-correlating one of these images with each of the others. Upon plotting a fixed (e.g., zero) component of the cross-correlation values as the spacing is increased over some empirically determined range, the system is calibrated. To measure height with the system, a spacing value is selected and a cross-correlation value is determined between two intensity images at a selected frequency spacing. The measured height is the slope of the cross-correlation value used. Both electronic and optical radar signal data compressors and cross-correlations are disclosed for implementation of the system.

Performance of High-Speed PWM Control Chips at Cryogenic Temperatures

NASA Technical Reports Server (NTRS)

Elbuluk, Malik E.; Gerber, Scott; Hammoud, Ahmad; Patterson, Richard; Overton, Eric

2001-01-01

The operation of power electronic systems at cryogenic temperatures is anticipated in many NASA space missions such as planetary exploration and deep space probes. In addition to surviving the space hostile environment, electronics capable of low temperature operation would contribute to improving circuit performance, increasing system efficiency, and reducing development and launch costs. As part of the NASA Glenn Low Temperature Electronics Program, several commercial high-speed Pulse Width Modulation (PWM) chips have been characterized in terms of their performance as a function of temperature in the range of 25 to -196 C (liquid nitrogen). These chips ranged in their electrical characteristics, modes of control, packaging options, and applications. The experimental procedures along with the experimental data obtained on the investigated chips are presented and discussed.

Noninvasive intracranial pressure estimation by orbital subarachnoid space measurement: the Beijing Intracranial and Intraocular Pressure (iCOP) study.

PubMed

Xie, Xiaobin; Zhang, Xiaojun; Fu, Jidi; Wang, Huaizhou; Jonas, Jost B; Peng, Xiaoxia; Tian, Guohong; Xian, Junfang; Ritch, Robert; Li, Lei; Kang, Zefeng; Zhang, Shoukang; Yang, Diya; Wang, Ningli

2013-07-24

The orbital subarachnoid space surrounding the optic nerve is continuous with the circulation system for cerebrospinal fluid (CSF) and can be visualized by using magnetic resonance imaging (MRI). We hypothesized that the orbital subarachnoid space width (OSASW) is correlated with and can serve as a surrogate for intracranial pressure (ICP). Our aim was to develop a method for a noninvasive measurement of the intracranial CSF-pressure (CSF-P) based on MRI-assisted OSASW. The prospective observational comparative study included neurology patients who underwent lumbar CSF-P measurement and 3.0-Tesla orbital magnetic resonance imaging (MRI) for other clinical reasons. The width of the orbital subarachnoid space (OSASW) around the optic nerve was measured with MRI at 3, 9, and 15 mm behind the globe. The study population was randomly divided into a training group and a test group. After adjusting for body mass index (BMI) and mean arterial blood pressure (MABP), algorithms for the associations between CSF-P and OSASW were calculated in the training group. The algorithms were subsequently verified in the test group. Main outcome measures were the width of the orbital subarachnoid space (OSASW) and the lumbar cerebrospinal fluid pressure (CSF-P). Seventy-two patients were included in the study. In the training group, the algorithms for the associations between CSF-P and OSASW were as follows: (a) CSF-P = 9.31 × OSASW (at 3 mm) + 0.48 × BMI + 0.14 × MABP-19.94; (b) CSF-P = 16.95 × OSASW (at 9 mm) + 0.39 × BMI + 0.14 × MABP-20.90; and (c) CSF-P = 17.54 × OSASW (at 15 mm) + 0.47 × BMI + 0.13 × MABP-21.52. Applying these algorithms in the independent test group, the measured lumbar CSF-P (13.6 ± 5.1 mm Hg) did not differ significantly from the calculated MRI-derived CSF-P (OSASW at 3 mm: 12.7 ± 4.2 mm Hg (P = 0.07); at 9 mm: 13.4 ± 5.1 mm Hg (P = 0.35); and at 15 mm: 14.0 ± 4.9 mm Hg (P = 0.87)). Intraclass correlation coefficients (ICCs) were higher for the CSF-P assessment based on OSASW at 9 mm and at 15 mm behind the globe (all ICCs, 0.87) than for OSASW measurements at 3 mm (ICC, 0.80). In patients with normal, moderately decreased or elevated ICP, MRI-assisted measurement of the OSASW appears to be useful for the noninvasive quantitative estimation of ICP, if BMI and MABP as contributing parameters are taken into account. Clinical trial registered with the Chinese Clinical Trial Registry: ChiCTR-OCC-11001271.

Process and apparatus for indirect-fired heating and drying

DOEpatents

Abbasi, Hamid Ali; Chudnovsky, Yaroslav

2005-04-12

A method for heating flat or curved surfaces comprising injecting fuel and oxidant along the length, width or longitudinal side of a combustion space formed between two flat or curved plates, transferring heat from the combustion products via convection and radiation to the surface being heated on to the material being dried/heated, and recirculating at least 20% of the combustion products to the root of the flame.

Space Particle Hazard Specification, Forecasting, and Mitigation

DTIC Science & Technology

2007-11-30

Automated FTP scripts permitted users to automatically update their global input parameter data set directly from the National Oceanic and...of CEASE capabilities. The angular field-of-view for CEASE is relatively large and will not allow for pitch angle resolved measurements. However... angular zones spanning 120° in the plane containing the magnetic field with an approximate 4° width in the direction perpendicular to the look-plane

Hollow - cathode electrode for high-power, high-pressure discharge devices

DOEpatents

Chang, Jim J.; Alger, Terry W.

1995-01-01

Several different cold cathode configurations for a gas discharge device each having a plurality of grooves of selected spacing, depth and width to improve the emission of electrons in a gas discharge device. Each of the cold cathode configurations can be machined from a single piece of a selected material. Several of the configurations can be assembled with individual elements which is easily seen from the various figures.

Metal matrix composite structural panel construction

NASA Technical Reports Server (NTRS)

Mcwithey, R. R.; Royster, D. M. (Inventor); Bales, T. T.

1983-01-01

Lightweight capped honeycomb stiffeners for use in fabricating metal or metal/matrix exterior structural panels on aerospace type vehicles and the process for fabricating same are disclosed. The stiffener stringers are formed in sheets, cut to the desired width and length and brazed in spaced relationship to a skin with the honeycomb material serving directly as the required lightweight stiffeners and not requiring separate metal encasement for the exposed honeycomb cells.

ADJUSTABLE DOUBLE PULSE GENERATOR

DOEpatents

Gratian, J.W.; Gratian, A.C.

1961-08-01

>A modulator pulse source having adjustable pulse width and adjustable pulse spacing is described. The generator consists of a cross coupled multivibrator having adjustable time constant circuitry in each leg, an adjustable differentiating circuit in the output of each leg, a mixing and rectifying circuit for combining the differentiated pulses and generating in its output a resultant sequence of negative pulses, and a final amplifying circuit for inverting and square-topping the pulses. (AEC)

The Difficulty of "Length x Width": Is a Square the Unit of Measurement?

ERIC Educational Resources Information Center

Kamii, Constance; Kysh, Judith

2006-01-01

In individual interviews, 220 students in grades 4, 6, 8, and 9 were given one task, and 72 eighth graders were given three tasks to answer two questions: (a) Is a square the unit of measurement for an area for students in grades 4-8? and (b) Does a square have a space-covering characteristic for students in grade 8? The answers to both questions…

Dissecting the actin cortex density and membrane-cortex distance in living cells by super-resolution microscopy

NASA Astrophysics Data System (ADS)

Clausen, M. P.; Colin-York, H.; Schneider, F.; Eggeling, C.; Fritzsche, M.

2017-02-01

Nanoscale spacing between the plasma membrane and the underlying cortical actin cytoskeleton profoundly modulates cellular morphology, mechanics, and function. Measuring this distance has been a key challenge in cell biology. Current methods for dissecting the nanoscale spacing either limit themselves to complex survey design using fixed samples or rely on diffraction-limited fluorescence imaging whose spatial resolution is insufficient to quantify distances on the nanoscale. Using dual-color super-resolution STED (stimulated-emission-depletion) microscopy, we here overcome this challenge and accurately measure the density distribution of the cortical actin cytoskeleton and the distance between the actin cortex and the membrane in live Jurkat T-cells. We found an asymmetric cortical actin density distribution with a mean width of 230 (+105/-125) nm. The spatial distances measured between the maximum density peaks of the cortex and the membrane were bi-modally distributed with mean values of 50  ±  15 nm and 120  ±  40 nm, respectively. Taken together with the finite width of the cortex, our results suggest that in some regions the cortical actin is closer than 10 nm to the membrane and a maximum of 20 nm in others.

Effect of chemoepitaxial guiding underlayer design on the pattern quality and shape of aligned lamellae for fabrication of line-space patterns

NASA Astrophysics Data System (ADS)

Nation, Benjamin D.; Peters, Andrew J.; Lawson, Richard A.; Ludovice, Peter J.; Henderson, Clifford L.

2017-10-01

Chemoepitaxial guidance of block copolymer directed self-assembly in thin films is explored using a coarse-grained molecular dynamics model. The underlayers studied are 2× density multiplying line-space patterns composed of repeating highly preferential pinning stripes of various widths separated by larger, more neutral, background regions of various compositions. Decreasing the pinning stripe width or making the background region more neutral is found to increase the line edge roughness (LER) of the lines, but these conditions are found to give the straightest sidewalls for the formed lines. Varying these underlayer properties is found to have minimal effect on linewidth roughness. A larger pinning stripe causes the pinned line (PL) to foot (expand near the substrate), and a preferential background region causes the unpinned line (UPL) to undercut (contract near the substrate). A simple model was developed to predict the optimal conditions to eliminate footing. Using this model, conditions are found that decrease footing of the PL, but these conditions increase undercutting in the UPL. Deformations in either the PL or UPL propagate to the other line. There exists a trade-off between LER and the footing/undercutting, that is, decreasing LER increases footing/undercutting and vice versa.

Domain wall motion in sub-100 nm magnetic wire

NASA Astrophysics Data System (ADS)

Siddiqui, Saima; Dutta, Sumit; Currivan, Jean Anne; Ross, Caroline; Baldo, Marc

2015-03-01

Nonvolatile memory devices such as racetrack memory rely on the manipulation of domain wall (DW) in magnetic nanowires, and scaling of these devices requires an understanding of domain wall behavior as a function of the wire width. Due to the increased importance of edge roughness and magnetostatic interaction, DW pinning increases dramatically as the wire dimensions decrease and stochastic behavior is expected depending on the distribution of pinning sites. We report on the field driven DW statistics in sub-100 nm wide nanowires made from Co films with very small edge roughness. The nanowires were patterned in the form of a set of concentric rings of 10 μm diameter. Two different width nanowires with two different spacings have been studied. The rings were first saturated in plane to produce onion states and then the DWs were translated in the wires using an orthogonal in-plane field. The position of the DWs in the nanowires was determined with magnetic force microscopy. From the positions of the DWs in the nanowires, the strength of the extrinsic pinning sites was identified and they follow two different distributions in two different types of nanowire rings. For the closely spaced wires, magnetostatic interactions led to correlated movement of DWs in neighboring wires. The implications of DW pinning and interaction in nanoscale DW devices will be discussed.

Smile attractiveness related to buccal corridor space in 3 different facial types: A perception of 3 ethnic groups of Malaysians.

PubMed

Nimbalkar, Smita; Oh, Yih Y; Mok, Reei Y; Tioh, Jing Y; Yew, Kai J; Patil, Pravinkumar G

2018-03-16

Buccal corridor space and its variations greatly influence smile attractiveness. Facial types are different for different ethnic populations, and so is smile attractiveness. The subjective perception of smile attractiveness of different populations may vary in regard to different buccal corridor spaces and facial patterns. The purpose of this study was to determine esthetic perceptions of the Malaysian population regarding the width of buccal corridor spaces and their effect on smile esthetics in individuals with short, normal, and long faces. The image of a smiling individual with a mesofacial face was modified to create 2 different facial types (brachyfacial and dolicofacial). Each face form was further modified into 5 different buccal corridors (2%, 10%, 15%, 22%, and 28%). The images were submitted to 3 different ethnic groups of evaluators (Chinese, Malay, Indian; 100 each), ranging between 17 and 21 years of age. A visual analog scale (50 mm in length) was used for assessment. The scores given to each image were compared with the Kruskal-Wallis test, and pairwise comparison was performed using the Mann-Whitney U test (α=.05). All 3 groups of evaluators could distinguish gradations of dark spaces in the buccal corridor at 2%, 10%, and 28%. Statistically significant differences were observed among 3 groups of evaluators in esthetic perception when pairwise comparisons were performed. A 15% buccal corridor was found to score esthetically equally within 3 face types by all 3 groups of evaluators. The Indian population was more critical in evaluation than the Chinese or Malay populations. In a pairwise comparison, more significant differences were found between long and short faces and the normal face; the normal face was compared with long and short faces separately. The width of the buccal corridor space influences smile attractiveness in different facial types. A medium buccal corridor (15%) is the esthetic characteristic preferred by all groups of evaluators in short, normal, and long face types. Copyright © 2017 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Spacing of Imbricated Thrust Faults and the Strength of Thrust-Belts and Accretionary Wedges

NASA Astrophysics Data System (ADS)

Ito, G.; Regensburger, P. V.; Moore, G. F.

2017-12-01

The pattern of imbricated thrust blocks is a prominent characteristic of the large-scale structure of thrust-belts and accretionary wedges around the world. Mechanical models of these systems have a rich history from laboratory analogs, and more recently from computational simulations, most of which, qualitatively reproduce the regular patterns of imbricated thrusts seen in nature. Despite the prevalence of these patterns in nature and in models, our knowledge of what controls the spacing of the thrusts remains immature at best. We tackle this problem using a finite difference, particle-in-cell method that simulates visco-elastic-plastic deformation with a Mohr-Coulomb brittle failure criterion. The model simulates a horizontal base that moves toward a rigid vertical backstop, carrying with it an overlying layer of crust. The crustal layer has a greater frictional strength than the base, is cohesive, and is initially uniform in thickness. As the layer contracts, a series of thrust blocks immerge sequentially and form a wedge having a mean taper consistent with that predicted by a noncohesive, critical Coulomb wedge. The widths of the thrust blocks (or spacing between adjacent thrusts) are greatest at the front of the wedge, tend to decrease with continued contraction, and then tend toward a pseudo-steady, minimum width. Numerous experiments show that the characteristic spacing of thrusts increases with the brittle strength of the wedge material (cohesion + friction) and decreases with increasing basal friction for low (<8°) taper angles. These relations are consistent with predictions of the elastic stresses forward of the frontal thrust and at what distance the differential stress exceeds the brittle threshold to form a new frontal thrust. Hence the characteristic spacing of the thrusts across the whole wedge is largely inherited at the very front of the wedge. Our aim is to develop scaling laws that will illuminate the basic physical processes controlling systems, as well as allow researchers to use observations of thrust spacing as an independent constraint on the brittle strength of wedges as well as their bases.

Dissolver vessel bottom assembly

DOEpatents

Kilian, Douglas C.

1976-01-01

An improved bottom assembly is provided for a nuclear reactor fuel reprocessing dissolver vessel wherein fuel elements are dissolved as the initial step in recovering fissile material from spent fuel rods. A shock-absorbing crash plate with a convex upper surface is disposed at the bottom of the dissolver vessel so as to provide an annular space between the crash plate and the dissolver vessel wall. A sparging ring is disposed within the annular space to enable a fluid discharged from the sparging ring to agitate the solids which deposit on the bottom of the dissolver vessel and accumulate in the annular space. An inlet tangential to the annular space permits a fluid pumped into the annular space through the inlet to flush these solids from the dissolver vessel through tangential outlets oppositely facing the inlet. The sparging ring is protected against damage from the impact of fuel elements being charged to the dissolver vessel by making the crash plate of such a diameter that the width of the annular space between the crash plate and the vessel wall is less than the diameter of the fuel elements.

On the role of precipitation latent heating in modulating the strength and width of the Hadley circulation

NASA Astrophysics Data System (ADS)

Mathew, Sneha Susan; Kumar, Karanam Kishore

2018-05-01

The latent heat released in the clouds over the tropics plays a vital role in driving the Hadley circulation (HC). The present study discusses the influence of latent heating (LH) on the HC parameters viz., centre, strength and total width by using precipitation LH profiles derived from the space-borne observations of the Precipitation Radar (PR) onboard Tropical Rain Measuring Mission (TRMM) and meridional stream function (MSF) derived from ECMWF-Interim reanalysis. The latitude of peak latent heating, width of the latent heating distribution and the total LH released within the ascending limb of the HC are estimated and their influence on the HC centre, strength and width is quantified, for the first time. The present results show that the latitude of peak LH significantly influences the position of the HC centre with correlation coefficient of 0.90. This high correlation between these two quantities seems to be due to their co-variability with the apparent motion of the Sun across the latitudes. The intensity of the HC in the NH as well as SH shows high correlation with the latitude of peak LH with coefficients - 0.85 and - 0.78, respectively. These results indicate that farther the latitude of peak LH from the equator in the summer hemisphere, stronger is the HC intensity in the winter hemisphere. The present analysis also reveals that the total LH released within the ascending limb of HC substantially influence the total width of the HC, with correlation coefficient 0.52, as compared to the other two LH parameters. This observation can be attributed to the fact that the HC is sensitive to the latent heat release in the mid-tropospheric levels in the tropics. An attempt is also made to investigate the degree of variability of these parameters after deseasonalization and results are discussed in the light of present understanding. The significance of the present study lies in providing the observational evidence for the influence of latent heating on the HC strength/width variability, quantitatively, for the first time using TRMM observations of precipitation latent heating.

Suppression of laser phase noise in direct-detection optical OFDM transmission using phase-conjugated pilots

NASA Astrophysics Data System (ADS)

Zhang, Lu; Ming, Yi; Li, Jin

2017-11-01

Due to the unique phase noise (PN) characteristics in direct-detection optical OFDM (DDO-OFDM) systems, the design of PN compensator is considered as a difficult task. In this paper, a laser PN suppression scheme with low complexity for DDO-OFDM based on coherent superposition of data carrying subcarriers and their phase conjugates is proposed. Through theoretical derivation, the obvious PN suppression is observed. The effectiveness of this technique is demonstrated by simulation of a 4-QAM DDO-OFDM system over 1000 km transmission length at different laser line-width and subcarrier frequency spacing. The results show that the proposed scheme can significantly suppress both varied phase rotation term (PTR) and inter-carrier interference (ICI), and the laser line-width can be relaxed with up to 9 dB OSNR saving or even breakthrough of performance floor.

Tailoring of the partial magnonic gap in three-dimensional magnetoferritin-based magnonic crystals

NASA Astrophysics Data System (ADS)

Mamica, S.

2013-07-01

We investigate theoretically the use of magnetoferritin nanoparticles, self-assembled in the protein crystallization process, as the basis for the realization of 3D magnonic crystals in which the interparticle space is filled with a ferromagnetic material. Using the plane wave method we study the dependence of the width of the partial band gap and its central frequency on the total magnetic moment of the magnetoferritin core and the lattice constant of the magnetoferritin crystal. We show that by adjusting the combination of these two parameters the partial gap can be tailored in a wide frequency range and shifted to sub-terahertz frequencies. Moreover, the difference in the width of the partial gap for spin waves propagating in planes parallel and perpendicular to the external field allows for switching on and off the partial magnonic gap by changing the direction of the applied field.

RAINIER: A simulation tool for distributions of excited nuclear states and cascade fluctuations

NASA Astrophysics Data System (ADS)

Kirsch, L. E.; Bernstein, L. A.

2018-06-01

A new code has been developed named RAINIER that simulates the γ-ray decay of discrete and quasi-continuum nuclear levels for a user-specified range of energy, angular momentum, and parity including a realistic treatment of level spacing and transition width fluctuations. A similar program, DICEBOX, uses the Monte Carlo method to simulate level and width fluctuations but is restricted in its initial level population algorithm. On the other hand, modern reaction codes such as TALYS and EMPIRE populate a wide range of states in the residual nucleus prior to γ-ray decay, but do not go beyond the use of deterministic functions and therefore neglect cascade fluctuations. This combination of capabilities allows RAINIER to be used to determine quasi-continuum properties through comparison with experimental data. Several examples are given that demonstrate how cascade fluctuations influence experimental high-resolution γ-ray spectra from reactions that populate a wide range of initial states.

The Defrosting South

NASA Technical Reports Server (NTRS)

2005-01-01

20 August 2005 This Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) image shows varied springtime patterns formed in defrosting, seasonal carbon dioxide frost in the south polar region of Mars. The feature sporting an outline of dark spots and an interior of smaller, closely-spaced dark spots and dark-outlined polygons is a patch of windblown or wind-eroded sand that was covered by carbon dioxide frost during the previous autumn and winter. The fainter, larger polygon pattern on either side of the patch of defrosting sand is formed in the substrate upon which the sand patch is sitting. Polygonal forms such as these might indicate the presence of ice below the surface.

Location near: 79.6oS, 125.0oW Image width: width: 3 km (1.9 mi) Illumination from: upper left Season: Southern Spring

Development of flame resistant treatment for Nomex fibrous structures

NASA Technical Reports Server (NTRS)

Toy, M. S.

1977-01-01

Flame resistant fibrous materials for space shuttle application were developed through chemical modification of commercially available aromatic polyamide fibrous products. The new surface treatment was achieved in the laboratory by ultraviolet activation of the fabric in the presence of fluoroolefin monomers and a diluent gas. The monomers grafted under these conditions provide the improved properties of the fabric in flame resistance, chemical inertness, and nonwettability without the sacrifice of color or physical properties. The laboratory reaction vessel was scaled-up to a batch continuous process, which treats ten yards of the commercial width textiles. The treated commercial width Nomex (HT-10-41) from the scaled-up reactor is self-extinguishing in an oxygen-enriched environment, water-repellent, soft, silky, and improved in chemical resistance. Unlike most textile processes, the grafting unit operates under dry conditions and no chemical by-products have to be washed out of the finished product.

Structural character of the Ghost Dance fault, Yucca Mountain, Nevada

USGS Publications Warehouse

Spengler, R.W.; Braun, C.A.; Linden, R.M.; Martin, L.G.; Ross-Brown, D. M.; Blackburn, R.L.

1993-01-01

Detailed structural mapping of an area that straddles the southern part of the Ghost Dance Fault has revealed the presence of several additional subparallel to anastomosing faults. These faults, mapped at a scale of 1:240, are: 1) dominantly north trending, 2) present on both the upthrown and downthrown sides of the surface trace of the Ghost Dance fault, 3) near-vertical features that commonly offset strata down to the west by 3 to 6 m (10 to 20 ft), and 4) commonly spaced 15 to 46 m (50 to 150 ft) apart. The zone also exhibits a structural fabric, containing an abundance of northwest-trending fractures. The width of the zone appears to be at least 213 m (700 ft) near the southernmost boundary of the study area but remains unknown near the northern extent of the study area, where the width of the study area is only 183 m (600 ft).

Causes of Early-Age Thermal Cracking of Concrete Foundation Slabs and their Reinforcement to Control the Cracking

NASA Astrophysics Data System (ADS)

Bilčík, Juraj; Sonnenschein, Róbert; Gažovičová, Natália

2017-09-01

This paper focuses on the causes and consequences of early-age cracking of mass concrete foundation slabs due to restrained volume changes. Considering the importance of water leaking through cracks in terms of the serviceability, durability and environmental impact of watertight concrete structures, emphasis is placed on the effect of temperature loads on foundation slabs. Foundation slabs are usually restrained to some degree externally or internally. To evaluate the effect of external restraints on foundation slabs, friction and interaction models are introduced. The reinforcement of concrete cannot prevent the initiation of cracking, but when cracking has occurred, it may act to reduce the spacing and width of cracks. According to EN 1992-1-1, results of calculating crack widths with local variations included in National Annexes (NAs) vary considerably. A comparison of the required reinforcement areas according to different NAs is presented.

Lorenz curve of a light beam: evaluating beam quality from a majorization perspective.

PubMed

Porras, Miguel A; Gonzalo, Isabel; Ahmir Malik, M

2017-08-01

We introduce a novel approach for the characterization of the quality of a laser beam that is not based on particular criteria for beam width definition. The Lorenz curve of a light beam is a sophisticated version of the so-called power-in-the-bucket curve, formed by the partial sums of discretized joint intensity distribution in the near and far fields, sorted in decreasing order. According to majorization theory, a higher Lorenz curve implies that all measures of spreading in phase space, and, in particular, all Rényi (and Shannon) entropy-based measures of the beam width products in near and far fields, are unanimously smaller, providing a strong assessment of a better beam quality. Two beams whose Lorenz curves intersect can be considered of relatively better or lower quality only according to specific criteria, which can be inferred from the plot of the respective Lorenz curves.

Analytical modeling of eddy-current losses caused by pulse-width-modulation switching in permanent-magnet brushless direct-current motors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Deng, F.; Nehl, T.W.

1998-09-01

Because of their high efficiency and power density the PM brushless dc motor is a strong candidate for electric and hybrid vehicle propulsion systems. An analytical approach is developed to predict the inverter high frequency pulse width modulation (PWM) switching caused eddy-current losses in a permanent magnet brushless dc motor. The model uses polar coordinates to take curvature effects into account, and is also capable of including the space harmonic effect of the stator magnetic field and the stator lamination effect on the losses. The model was applied to an existing motor design and was verified with the finite elementmore » method. Good agreement was achieved between the two approaches. Hence, the model is expected to be very helpful in predicting PWM switching losses in permanent magnet machine design.« less

Seat and seatbelt accommodation in fire apparatus: Anthropometric aspects

PubMed Central

Hsiao, Hongwei; Whitestone, Jennifer; Wilbur, Michael; Lackore, J. Roger; Routley, J. Gordon

2015-01-01

This study developed anthropometric information on U.S. firefighters to guide fire-apparatus seat and seatbelt designs and future standards development. A stratified sample of 863 male and 88 female firefighters across the U.S. participated in the study. The study results suggested 498 mm in width, 404 mm in depth, and 365–476 mm in height for seat pans; 429–522 mm in width and 542 mm in height for seat back; 871 mm in height for head support; a seat space of 733 mm at shoulder and 678 mm at hip; and a knee/leg clearance of 909 mm in fire truck cab. Also, 1520 mm of lap belt web effective length and 2828 mm of lap-and-shoulder belt web effective length were suggested. These data for firetruck seats and seatbelts provide a foundation for fire apparatus manufacturers and standards committees to improve firefighter seat designs and seatbelt usage compliance. PMID:26154212

Parametric study in weld mismatch of longitudinally welded SSME HPFTP inlet

NASA Technical Reports Server (NTRS)

Min, J. B.; Spanyer, K. L.; Brunair, R. M.

1991-01-01

Welded joints are an essential part of pressure vessels such as the Space Shuttle Main Engine (SSME) Turbopumps. Defects produced in the welding process can be detrimental to weld performance. Recently, review of the SSME high pressure fuel turbopump (HPFTP) titanium inlet x rays revealed several weld discrepancies such as penetrameter density issues, film processing discrepancies, weld width discrepancies, porosity, lack of fusion, and weld offsets. Currently, the sensitivity of welded structures to defects is of concern. From a fatigue standpoint, weld offset may have a serious effect since local yielding, in general, aggravates cyclic stress effects. Therefore, the weld offset issue is considered. Using the finite element method and mathematical formulations, parametric studies were conducted to determine the influence of weld offsets and a variation of weld widths in longitudinally welded cylindrical structures with equal wall thickness on both sides of the joint. From the study, the finite element results and theoretical solutions are presented.

Coupling Between Microstrip Lines With Finite Width Ground Plane Embedded in Thin Film Circuits

NASA Technical Reports Server (NTRS)

Ponchak, George E.; Dalton, Edan; Tentzeris, Manos M.; Papapolymerou, John

2003-01-01

Three-dimensional (3D) interconnects built upon multiple layers of polyimide are required for constructing 3D circuits on CMOS (low resistivity) Si wafers, GaAs, and ceramic substrates. Thin film microstrip lines (TFMS) with finite width ground planes embedded in the polyimide are often used. However, the closely spaced TFMS lines a r e susceptible to high levels of coupling, which degrades circuit performance. In this paper, Finite Difference Time Domain (FDTD) analysis and experimental measurements a r e used to show that the ground planes must be connected by via holes to reduce coupling in both the forward and backward directions. Furthermore, it is shown that coupled microstrip lines establish a slotline type mode between the two ground planes and a dielectric waveguide type mode, and that the via holes recommended here eliminate these two modes.

Statistics of equivalent width data and new oscillator strengths for Si II, Fe II, and Mn II. [in interstellar medium

NASA Technical Reports Server (NTRS)

Van Buren, Dave

1986-01-01

Equivalent width data from Copernicus and IUE appear to have an exponential, rather than a Gaussian distribution of errors. This is probably because there is one dominant source of error: the assignment of the background continuum shape. The maximum likelihood method of parameter estimation is presented for the case of exponential statistics, in enough generality for application to many problems. The method is applied to global fitting of Si II, Fe II, and Mn II oscillator strengths and interstellar gas parameters along many lines of sight. The new values agree in general with previous determinations but are usually much more tightly constrained. Finally, it is shown that care must be taken in deriving acceptable regions of parameter space because the probability contours are not generally ellipses whose axes are parallel to the coordinate axes.

Detailed non-LTE calculations of the iron emission from NGC 1068

NASA Technical Reports Server (NTRS)

Band, David L.; Klein, Richard I.; Castor, John I.; Nash, J. K.

1989-01-01

The X-ray iron line emission from NGC 1068 observed by the Ginga satellite is modeled using the new multiline, multilevel, non-LTE radiative transport code ALTAIR and a detailed atomic model for Ne-like through stripped iron. The parameter space of the obscured type 1 Seyfert nucleus model for this object is studied. The equivalent width is greater than previously predicted. It is found that detailed radiative transfer can have a significant effect on the observed line flux both for the K alpha line and for the L-shell emission. The ionization of the iron increases with temperature. Therefore the K alpha equivalent width and energy is a function not only of the ionization parameter, but also of the column depth and temperature. For a likely model of NGC 1068 it is found that the iron abundance is about twice solar, but that modifications of this model may permit a smaller abundance.

Dual optical mechanical position tracker

NASA Astrophysics Data System (ADS)

Everett, S. L., Jr.

1985-06-01

This patent application describes an apparatus for retaining control of moving carriage impact dot matrix print heads when subjected to strong external forces such as shock and/or vibration. Position and direction of carriage movement is provided by a photo emitter-sensor assembly and a slotted timing wheel or disc having a plurality of equally spaced slots whose slot width is equal to the slot separation. The slot width is sufficient to frame a pair of side-by-side emitters which operate in conjunction with a pair of side-by-side sensors on the other side of the timing wheel. The order or sequence in which the sensors receive photo energy from their respective emitters indicates the direction of rotation of the timing wheel while simultaneous reception of photo energy by the side-by-side sensors provides an indication of valid rest position of the carriage drive motor.

Variation of high-power aluminum-wire array Z-pinch dynamics with wire number, load mass, and array radius

NASA Astrophysics Data System (ADS)

Sanford, T. W. L.; Mock, R. C.; Marder, B. M.; Nash, T. J.; Spielman, R. B.; Peterson, D. L.; Roderick, N. F.; Hammer, J. H.; De Groot, J. S.; Mosher, D.; Whitney, K. G.; Apruzese, J. P.

1997-05-01

A systematic study of annular aluminum-wire z-pinches on the Saturn accelerator shows that the quality of the implosion, (as measured by the radial convergence, the radiated energy, pulse width, and power), increases with wire number. Radiation magnetohydrodynamic (RMHC) xy simulations suggest that the implosion transitions from that of individual wire plasmas to that of a continuous plasma shell when the interwire spacing is reduced below ˜1.4 mm. In this "plasma-shell regime," many of the global radiation and plasma characteristics are in agreement with those simulated by 2D-RMHC rz simulations. In this regime, measured changes in the radiation pulse width with variations in load mass and array radius are consistent with the simulations and are explained by the development of 2D fluid motion in the rz plane. Associated variations in the K-shell yield are qualitatively explained by simple radiation-scaling models.

Solare Cell Roof Tile And Method Of Forming Same

DOEpatents

Hanoka, Jack I.; Real, Markus

1999-11-16

A solar cell roof tile includes a front support layer, a transparent encapsulant layer, a plurality of interconnected solar cells and a backskin layer. The front support layer is formed of light transmitting material and has first and second surfaces. The transparent encapsulant layer is disposed adjacent the second surface of the front support layer. The interconnected solar cells has a first surface disposed adjacent the transparent encapsulant layer. The backskin layer has a first surface disposed adjacent a second surface of the interconnected solar cells, wherein a portion of the backskin layer wraps around and contacts the first surface of the front support layer to form the border region. A portion of the border region has an extended width. The solar cell roof tile may have stand-offs disposed on the extended width border region for providing vertical spacing with respect to an adjacent solar cell roof tile.

[Mapping mini-implant anatomic sites in the area of the maxillary first molar with the aid of the NewTom 3G® system].

PubMed

Dumitrache, Marius; Grenard, Annabelle

2010-12-01

The goal of our study was to construct a map of the implant sites in the region of the attached gingiva around the maxillary first molars that would be appropriate locations for placement of miniscrews to serve as orthodontic anchorage. We conducted 58 radiographic examinations with the NewTom 3G(®) cone beam technique. For each interdental space, between upper second bicuspids and first molars (5/6) and between upper first and second molars (6/7), we studied the mesio-distal width and depth of bucco-lingual bone at two different levels, L1 and L2, that corresponded to the lower and upper limits of the attached gingiva in the general population. The widths of the interdental spaces varied very little between L1 and L2 and their variances were comparable. At the level of the 5/6 space, the interdental widths displayed a Gaussian distribution, which made it possible for us to determine the confidence intervals at the two borders of attached gingiva as a function of age: IC(99%) of L1 = [2.045 ; 3.462] from 12 to 17 years or [1.594 ; 2.519] from 18 to 24 or [1.613 ; 2.5] from 25 to 48 years and IC(99%) of L2 = [2.37 ; 3.69] from 12 to 17 years or [1.5 ; 2.613] from 18 to 24 or [1.546 ; 2.619] from 25 to 48 ans. The interdental depths increased in an apical direction and their variance diminished. Even if the adequacy of the Gaussian law is less reliable in the sagittal plane, we find a greater consistency in depths in the spaces around 5/6 that allows us to establish very precise confidence levels: IC(99%) of L1 = [9.213; 10.575] and IC(99%) of L2 = [10.295; 11.593]. The mesial areas of the first molars constitute safe zones for implantation of miniscrews with a maximum of 2-2.3 mm for 12 to 17 years old or 1.5-1.6 mm for 18 to 48 year olds and of a maximum of 9-10 mm in length whether the attached gingival level is strong or feeble. The distal areas of the first molars, because of their great variability, require an individualized radiographic study before any mini/screw can be placed. © EDP Sciences, SFODF, 2010.

Semiclassical propagation: Hilbert space vs. Wigner representation

NASA Astrophysics Data System (ADS)

Gottwald, Fabian; Ivanov, Sergei D.

2018-03-01

A unified viewpoint on the van Vleck and Herman-Kluk propagators in Hilbert space and their recently developed counterparts in Wigner representation is presented. Based on this viewpoint, the Wigner Herman-Kluk propagator is conceptually the most general one. Nonetheless, the respective semiclassical expressions for expectation values in terms of the density matrix and the Wigner function are mathematically proven here to coincide. The only remaining difference is a mere technical flexibility of the Wigner version in choosing the Gaussians' width for the underlying coherent states beyond minimal uncertainty. This flexibility is investigated numerically on prototypical potentials and it turns out to provide neither qualitative nor quantitative improvements. Given the aforementioned generality, utilizing the Wigner representation for semiclassical propagation thus leads to the same performance as employing the respective most-developed (Hilbert-space) methods for the density matrix.

Partitioning of the degradation space for OCR training

NASA Astrophysics Data System (ADS)

Barney Smith, Elisa H.; Andersen, Tim

2006-01-01

Generally speaking optical character recognition algorithms tend to perform better when presented with homogeneous data. This paper studies a method that is designed to increase the homogeneity of training data, based on an understanding of the types of degradations that occur during the printing and scanning process, and how these degradations affect the homogeneity of the data. While it has been shown that dividing the degradation space by edge spread improves recognition accuracy over dividing the degradation space by threshold or point spread function width alone, the challenge is in deciding how many partitions and at what value of edge spread the divisions should be made. Clustering of different types of character features, fonts, sizes, resolutions and noise levels shows that edge spread is indeed shown to be a strong indicator of the homogeneity of character data clusters.

The Nosé–Hoover looped chain thermostat for low temperature thawed Gaussian wave-packet dynamics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Coughtrie, David J.; Tew, David P.

2014-05-21

We have used a generalised coherent state resolution of the identity to map the quantum canonical statistical average for a general system onto a phase-space average over the centre and width parameters of a thawed Gaussian wave packet. We also propose an artificial phase-space density that has the same behaviour as the canonical phase-space density in the low-temperature limit, and have constructed a novel Nosé–Hoover looped chain thermostat that generates this density in conjunction with variational thawed Gaussian wave-packet dynamics. This forms a new platform for evaluating statistical properties of quantum condensed-phase systems that has an explicit connection to themore » time-dependent Schrödinger equation, whilst retaining many of the appealing features of path-integral molecular dynamics.« less

Design to Improve Visibility: Impact of Corridor Width and Unit Shape.

PubMed

Hadi, Khatereh; Zimring, Craig

2016-07-01

This study analyzes 10 intensive care units (ICUs) to understand the associations between design features of space layout and nurse-to-patient visibility parameters. Previous studies have explored how different hospital units vary in their visibility relations and how such varied visibility relations result in different nurse behaviors toward patients. However, more limited research has examined the specific design attributes of the layouts that determine the varied visibility relations in the unit. Changes in size, geometry, or other attributes of design elements in nursing units, which might affect patient observation opportunities, require more research. This article reviews the literature to indicate evidence for the impact of hospital unit design on nurse/patient visibility relations and to identify design parameters shown to affect visibility. It further focuses on 10 ICUs to investigate how different layouts diverge regarding their visibility relations using a set of metrics developed by other researchers. Shape geometry and corridor width, as two selected design features, are compared. Corridor width and shape characteristics of ICUs are positively correlated with visibility. Results suggest that floor plans, which are repeatedly broken down into smaller convex (higher convex fragmentation values), or units, which have longer distances between their rooms or between their two opposite ends (longer relative grid distances), might have lower visibility levels across the unit. The findings of this study also suggest that wider corridors positively affect visibility of patient rooms. Changes in overall shape configuration and corridor width of nursing units may have important effects on patient observation and monitoring opportunities. © The Author(s) 2016.

Infrared contrast data analysis method for quantitative measurement and monitoring in flash infrared thermography

NASA Astrophysics Data System (ADS)

Koshti, Ajay M.

2015-04-01

The paper provides information on a new infrared (IR) image contrast data post-processing method that involves converting raw data to normalized contrast versus time evolutions from the flash infrared thermography inspection video data. Thermal measurement features such as peak contrast, peak contrast time, persistence time, and persistence energy are calculated from the contrast evolutions. In addition, simulation of the contrast evolution is achieved through calibration on measured contrast evolutions from many flat bottom holes in a test plate of the subject material. The measurement features are used to monitor growth of anomalies and to characterize the void-like anomalies. The method was developed to monitor and analyze void-like anomalies in reinforced carbon-carbon (RCC) materials used on the wing leading edge of the NASA Space Shuttle Orbiters, but the method is equally applicable to other materials. The thermal measurement features relate to the anomaly characteristics such as depth and size. Calibration of the contrast is used to provide an assessment of the anomaly depth and width which correspond to the depth and diameter of the equivalent flat bottom hole (EFBH) from the calibration data. An edge detection technique called the half-max is used to measure width and length of the anomaly. Results of the half-max width and the EFBH diameter are compared with actual widths to evaluate utility of IR Contrast method. Some thermal measurements relate to gap thickness of the delaminations. Results of IR Contrast method on RCC hardware are provided. Keywords: normalized contrast, flash infrared thermography.

Degree of target utilization influences the location of movement endpoint distributions.

PubMed

Slifkin, Andrew B; Eder, Jeffrey R

2017-03-01

According to dominant theories of motor control, speed and accuracy are optimized when, on the average, movement endpoints are located at the target center and when the variability of the movement endpoint distributions is matched to the width of the target (viz., Meyer, Abrams, Kornblum, Wright, & Smith, 1988). The current study tested those predictions. According to the speed-accuracy trade-off, expanding the range of variability to the amount permitted by the limits of the target boundaries allows for maximization of movement speed while centering the distribution on the target center prevents movement errors that would have occurred had the distribution been off center. Here, participants (N=20) were required to generate 100 consecutive targeted hand movements under each of 15 unique conditions: There were three movement amplitude requirements (80, 160, 320mm) and within each there were five target widths (5, 10, 20, 40, 80mm). According to the results, it was only at the smaller target widths (5, 10mm) that movement endpoint distributions were centered on the target center and the range of movement endpoint variability matched the range specified by the target boundaries. As target width increased (20, 40, 80mm), participants increasingly undershot the target center and the range of movement endpoint variability increasingly underestimated the variability permitted by the target region. The degree of target center undershooting was strongly predicted by the difference between the size of the target and the amount of movement endpoint variability, i.e., the amount of unused space in the target. The results suggest that participants have precise knowledge of their variability relative to that permitted by the target, and they use that knowledge to systematically reduce the travel distance to targets. The reduction in travel distance across the larger target widths might have resulted in greater cost savings than those associated with increases in speed. Copyright © 2017. Published by Elsevier B.V.

Wider stall space affects behavior, lesion scores, and productivity of gestating sows.

PubMed

Salak-Johnson, J L; DeDecker, A E; Levitin, H A; McGarry, B M

2015-10-01

Limited space allowance within the standard gestation stall is an important welfare concern because it restricts the ability of the sow to make postural adjustments and hinders her ability to perform natural behaviors. Therefore, we evaluated the impacts of increasing stall space and/or providing sows the freedom to access a small pen area on sow well-being using multiple welfare metrics. A total of 96 primi- and multiparous crossbred sows were randomly assigned in groups of 4 sows/treatment across 8 replicates to 1 of 3 stall treatments (TRT): standard stall (CTL; dimensions: 61 by 216 cm), width-adjustable stall (flex stall [FLX]; dimensions: adjustable width of 56 to 79 cm by 216 cm), or an individual walk-in/lock-in stall with access to a small communal open-pen area at the rear of the stall (free-access stall [FAS]; dimensions: 69 by 226 cm). Lesion scores, behavior, and immune and productivity traits were measured at various gestational days throughout the study. Total lesion scores were greatest for sows in FAS and least for sows in FLX ( < 0.001). Higher-parity sows in FAS had the most severe lesion scores (TRT × parity, < 0.0001) and scores were greatest at all gestational days (TRT × day, < 0.05). Regardless of parity, sows in FLX had the least severe scores ( < 0.0001). As pregnancy progressed, lesion scores increased among sows in CTL ( < 0.05). Sow BW and backfat (BF) were greater for sows in FLX and FAS ( < 0.05), and BCS and BF were greater for parity 1 and 2 sows in FAS than the same parity sows in CTL (TRT × parity, < 0.05). Duration and frequency of some postural behaviors and sham chew behavior were affected by TRT ( < 0.05) and time of day (TRT × day, < 0.05). These data indicate that adequate stall space, especially late in gestation, may improve the well-being of higher-parity and heavier-bodied gestating sows as assessed by changes in postural behaviors, lesion severity scores, and other sow traits. Moreover, compromised welfare measures found among sows in various stall environments may be partly attributed to the specific constraints of each stall system such as restricted stall space in CTL, insufficient floor space in the open-pen area of the FAS system, and gate design of the FLX (e.g., direction of bars and feeder space). These results also indicate that parity and gestational day are additional factors that may exacerbate the effects of restricted stall space or insufficient pen space, further compromising sow well-being.

Diagnostics of underwater electrical wire explosion through a time- and space-resolved hard x-ray source

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sheftman, D.; Shafer, D.; Efimov, S.

2012-10-15

A time- and space-resolved hard x-ray source was developed as a diagnostic tool for imaging underwater exploding wires. A {approx}4 ns width pulse of hard x-rays with energies of up to 100 keV was obtained from the discharge in a vacuum diode consisting of point-shaped tungsten electrodes. To improve contrast and image quality, an external pulsed magnetic field produced by Helmholtz coils was used. High resolution x-ray images of an underwater exploding wire were obtained using a sensitive x-ray CCD detector, and were compared to optical fast framing images. Future developments and application of this diagnostic technique are discussed.

KSC-2012-4541

NASA Image and Video Library

2012-08-17

CAPE CANAVERAL, Fla. – Two fish swim near the Banana River shoreline at NASA's Kennedy Space Center in Florida. Kennedy is located on Merritt Island, a barrier island, about 34 miles long and varying in width from five to 10 miles. Only 6,000 acres are actually used for operational activities. The Kennedy Space Center is also a National Wildlife Refuge. Consisting of 140,000 acres, the refuge provides a wide variety of habitats: coastal dunes, saltwater estuaries and marshes, freshwater impoundments, scrub, pine flatwoods and hardwood hammocks providing habitat for more than 1,500 species of plants and animals. For more information, visit: http://ipv6.nasa.gov/centers/kennedy/shuttleoperations/alligators/kscovrv.html Photo credit: NASA/Ben Smegelsky

Random pulse generator

NASA Technical Reports Server (NTRS)

Lindsey, R. S., Jr. (Inventor)

1975-01-01

An exemplary embodiment of the present invention provides a source of random width and random spaced rectangular voltage pulses whose mean or average frequency of operation is controllable within prescribed limits of about 10 hertz to 1 megahertz. A pair of thin-film metal resistors are used to provide a differential white noise voltage pulse source. Pulse shaping and amplification circuitry provide relatively short duration pulses of constant amplitude which are applied to anti-bounce logic circuitry to prevent ringing effects. The pulse outputs from the anti-bounce circuits are then used to control two one-shot multivibrators whose output comprises the random length and random spaced rectangular pulses. Means are provided for monitoring, calibrating and evaluating the relative randomness of the generator.

Diagnostics of underwater electrical wire explosion through a time- and space-resolved hard x-ray source.

PubMed

Sheftman, D; Shafer, D; Efimov, S; Gruzinsky, K; Gleizer, S; Krasik, Ya E

2012-10-01

A time- and space-resolved hard x-ray source was developed as a diagnostic tool for imaging underwater exploding wires. A ~4 ns width pulse of hard x-rays with energies of up to 100 keV was obtained from the discharge in a vacuum diode consisting of point-shaped tungsten electrodes. To improve contrast and image quality, an external pulsed magnetic field produced by Helmholtz coils was used. High resolution x-ray images of an underwater exploding wire were obtained using a sensitive x-ray CCD detector, and were compared to optical fast framing images. Future developments and application of this diagnostic technique are discussed.

Standardized UXO Technology Demonstration Site Open Field Scoring Record No. 908

DTIC Science & Technology

2008-08-01

demonstration at Aberdeen Proving Ground, a system with eight fluxgate magnetometers (Foerster CON650 gradiometers) and RTK-DGPS georeferencing will...be used. The spacing between the individual fluxgate sensors will be 25 cm (ca. 10 inches), totaling to a swath width of 2 m. c. The MAGNETO...MX system consists of: the MX-compact hardware multiplexer electronic module, up to 32 fluxgate gradiometers (for the APG demonstration: 8 fluxgate

U.S. Army/FRG Army Mobility Symposium Proceedings held in April 1975

DTIC Science & Technology

1975-11-01

widths, etC.--and their interactions with soil strength, tree stems of various sizes and spacings, approach angles in ditches and streams, etc. At the...provides for their specific identification and user control so that the effects of various levels of driver motivation, associated with combat or...prevailing in the areal unit (braking-visility limit). d. Maneuvering to avoid trees and/or obstacles. e. Acceleration and deceleration between obstacles

Hollow-cathode electrode for high-power, high-pressure discharge devices

DOEpatents

Chang, J.J.; Alger, T.W.

1995-08-22

Several different cold cathode configurations are disclosed for a gas discharge device each having a plurality of grooves of selected spacing, depth and width to improve the emission of electrons in a gas discharge device. Each of the cold cathode configurations can be machined from a single piece of a selected material. Several of the configurations can be assembled with individual elements which is easily seen from the various figures. 8 figs.

Compact Color Schlieren Optical System

NASA Technical Reports Server (NTRS)

Buchele, Donald R.; Griffin, Devon W.

1996-01-01

Compact, rugged optical system developed for use in rainbow schlieren deflectometry. Features unobscured telescope with focal-length/aperture-width ratio of 30. Made of carefully selected but relatively inexpensive parts. All of lenses stock items. By-product of design is optical system with loose tolerances on interlens spacing. One of resulting advantages, insensitivity to errors in fabrication of optomechanical mounts. Another advantage is ability to compensate for some of unit-to-unit variations inherent in stock lenses.

Alternate high capacity heat pipe

NASA Technical Reports Server (NTRS)

Voss, F. E.

1986-01-01

The performance predictions for a fifty foot heat pipe (4 foot evaporator - 46 foot condensor) are discussed. These performance predictions are supported by experimental data for a four foot heat pipe. Both heat pipes have evaporators with axial groove wick structures and condensers with powder metal external artery wick structures. The predicted performance of a rectangular axial groove/external artery heat pipe operating in space is given. Heat transport versus groove width is plotted for 100, 200 and 300 grooves in the evaporator. The curves show that maximum power is achieved for groove widths from 0.040 to 0.053 as the number of grooves varies from 300 to 100. The corresponding range of maximum power is 3150 to 2400 watts. The relationships between groove width and heat pipe evaporate diameter for 100, 200 and 300 grooves in the evaporator are given. A four foot heat pipe having a three foot condenser and one foot evaporator was built and tested. The evaporator wick structure used axial grooves with rectangular cross sections, and the condenser wick structure used powder metal with an external artery configuration. Fabrication drawings are enclosed. The predicted and measured performance for this heat pipe is shown. The agreement between predicted and measured performance is good and therefore substantiates the predicted performance for a fifty foot heat pipe.

Detection of co-seismic earthquake gravity field signals using GRACE-like mission simulations

NASA Astrophysics Data System (ADS)

Sharifi, Mohammad Ali; Shahamat, Abolfazl

2017-05-01

After launching the GRACE satellite mission in 2002, the earth's gravity field and its temporal variations are measured with a closer inspection. Although these variations are mainly because of the mass transfer of land water storage, they can also happen due to mass movements related to some natural phenomena including earthquakes, volcanic eruptions, melting of polar ice caps and glacial isostatic adjustment. Therefore this paper shows which parameters of an earthquake are more sensitive to GRACE-Like satellite missions. For this purpose, the parameters of the Maule earthquake that occurred in recent years and Alaska earthquake that occurred in 1964 have been chosen. Then we changed their several parameters to serve our purpose. The GRACE-Like sensitivity is observed by using the simulation of the earthquakes along with gravity changes they caused, as well as using dislocation theory under a half space earth. This observation affects the various faulting parameters which include fault length, width, depth and average slip. These changes were therefore evaluated and the result shows that the GRACE satellite missions tend to be more sensitive to Width among the Length and Width, the other parameter is Dip variations than other parameters. This article can be useful to the upcoming scenario designers and seismologists in their quest to study fault parameters.

The sensitivity of hearing-impaired adults to acoustic attributes in simulated rooms

PubMed Central

Whitmer, William M.; McShefferty, David; Akeroyd, Michael A.

2016-01-01

In previous studies we have shown that older hearing-impaired individuals are relatively insensitive to changes in the apparent width of broadband noises when those width changes were based on differences in interaural coherence [W. Whitmer, B. Seeber and M. Akeroyd, J. Acoust. Soc. Am. 132, 369-379 (2012)]. This insensitivity has been linked to senescent difficulties in resolving binaural fine-structure differences. It is therefore possible that interaural coherence, despite its widespread use, may not be the best acoustic surrogate of spatial perception for the aged and impaired. To test this, we simulated the room impulse responses for various acoustic scenarios with differing coherence and lateral (energy) fraction attributes using room modelling software (ODEON). Bilaterally impaired adult participants were asked to sketch the perceived size of speech tokens and musical excerpts that were convolved with these impulse responses and presented to them in a sound-dampened enclosure through a 24-loudspeaker array. Participants’ binaural acuity was also measured using an interaural phase discrimination task. Corroborating our previous findings, the results showed less sensitivity to interaural coherence in the auditory source width judgments of older hearing-impaired individuals, indicating that alternate acoustic measurements in the design of spaces for the elderly may be necessary. PMID:27213028

Prediction and Optimization of Phase Transformation Region After Spot Continual Induction Hardening Process Using Response Surface Method

NASA Astrophysics Data System (ADS)

Qin, Xunpeng; Gao, Kai; Zhu, Zhenhua; Chen, Xuliang; Wang, Zhou

2017-09-01

The spot continual induction hardening (SCIH) process, which is a modified induction hardening, can be assembled to a five-axis cooperating computer numerical control machine tool to strengthen more than one small area or relatively large area on complicated component surface. In this study, a response surface method was presented to optimize phase transformation region after the SCIH process. The effects of five process parameters including feed velocity, input power, gap, curvature and flow rate on temperature, microstructure, microhardness and phase transformation geometry were investigated. Central composition design, a second-order response surface design, was employed to systematically estimate the empirical models of temperature and phase transformation geometry. The analysis results indicated that feed velocity has a dominant effect on the uniformity of microstructure and microhardness, domain size, oxidized track width, phase transformation width and height in the SCIH process while curvature has the largest effect on center temperature in the design space. The optimum operating conditions with 0.817, 0.845 and 0.773 of desirability values are expected to be able to minimize ratio (tempering region) and maximize phase transformation width for concave, flat and convex surface workpieces, respectively. The verification result indicated that the process parameters obtained by the model were reliable.

Estimating daily time series of streamflow using hydrological model calibrated based on satellite observations of river water surface width: Toward real world applications.

PubMed

Sun, Wenchao; Ishidaira, Hiroshi; Bastola, Satish; Yu, Jingshan

2015-05-01

Lacking observation data for calibration constrains applications of hydrological models to estimate daily time series of streamflow. Recent improvements in remote sensing enable detection of river water-surface width from satellite observations, making possible the tracking of streamflow from space. In this study, a method calibrating hydrological models using river width derived from remote sensing is demonstrated through application to the ungauged Irrawaddy Basin in Myanmar. Generalized likelihood uncertainty estimation (GLUE) is selected as a tool for automatic calibration and uncertainty analysis. Of 50,000 randomly generated parameter sets, 997 are identified as behavioral, based on comparing model simulation with satellite observations. The uncertainty band of streamflow simulation can span most of 10-year average monthly observed streamflow for moderate and high flow conditions. Nash-Sutcliffe efficiency is 95.7% for the simulated streamflow at the 50% quantile. These results indicate that application to the target basin is generally successful. Beyond evaluating the method in a basin lacking streamflow data, difficulties and possible solutions for applications in the real world are addressed to promote future use of the proposed method in more ungauged basins. Copyright © 2015 The Authors. Published by Elsevier Inc. All rights reserved.

The sensitivity of hearing-impaired adults to acoustic attributes in simulated rooms.

PubMed

Whitmer, William M; McShefferty, David; Akeroyd, Michael A

2013-06-02

In previous studies we have shown that older hearing-impaired individuals are relatively insensitive to changes in the apparent width of broadband noises when those width changes were based on differences in interaural coherence [W. Whitmer, B. Seeber and M. Akeroyd, J. Acoust. Soc. Am. 132, 369-379 (2012)]. This insensitivity has been linked to senescent difficulties in resolving binaural fine-structure differences. It is therefore possible that interaural coherence, despite its widespread use, may not be the best acoustic surrogate of spatial perception for the aged and impaired. To test this, we simulated the room impulse responses for various acoustic scenarios with differing coherence and lateral (energy) fraction attributes using room modelling software (ODEON). Bilaterally impaired adult participants were asked to sketch the perceived size of speech tokens and musical excerpts that were convolved with these impulse responses and presented to them in a sound-dampened enclosure through a 24-loudspeaker array. Participants' binaural acuity was also measured using an interaural phase discrimination task. Corroborating our previous findings, the results showed less sensitivity to interaural coherence in the auditory source width judgments of older hearing-impaired individuals, indicating that alternate acoustic measurements in the design of spaces for the elderly may be necessary.

Directed self assembly of block copolymers using chemical patterns with sidewall guiding lines, backfilled with random copolymer brushes.

PubMed

Pandav, Gunja; Durand, William J; Ellison, Christopher J; Willson, C Grant; Ganesan, Venkat

2015-12-21

Recently, alignment of block copolymer domains has been achieved using a topographically patterned substrate with a sidewall preferential to one of the blocks. This strategy has been suggested as an option to overcome the patterning resolution challenges facing chemoepitaxy strategies, which utilize chemical stripes with a width of about half the period of block copolymer to orient the equilibrium morphologies. In this work, single chain in mean field simulation methodology was used to study the self assembly of symmetric block copolymers on topographically patterned substrates with sidewall interactions. Random copolymer brushes grafted to the background region (space between patterns) were modeled explicitly. The effects of changes in pattern width, film thicknesses and strength of sidewall interaction on the resulting morphologies were examined and the conditions which led to perpendicular morphologies required for lithographic applications were identified. A number of density multiplication schemes were studied in order to gauge the efficiency with which the sidewall pattern can guide the self assembly of block copolymers. The results indicate that such a patterning technique can potentially utilize pattern widths of the order of one-two times the period of block copolymer and still be able to guide ordering of the block copolymer domains up to 8X density multiplication.

The extent of visual space inferred from perspective angles

PubMed Central

Erkelens, Casper J.

2015-01-01

Retinal images are perspective projections of the visual environment. Perspective projections do not explain why we perceive perspective in 3-D space. Analysis of underlying spatial transformations shows that visual space is a perspective transformation of physical space if parallel lines in physical space vanish at finite distance in visual space. Perspective angles, i.e., the angle perceived between parallel lines in physical space, were estimated for rails of a straight railway track. Perspective angles were also estimated from pictures taken from the same point of view. Perspective angles between rails ranged from 27% to 83% of their angular size in the retinal image. Perspective angles prescribe the distance of vanishing points of visual space. All computed distances were shorter than 6 m. The shallow depth of a hypothetical space inferred from perspective angles does not match the depth of visual space, as it is perceived. Incongruity between the perceived shape of a railway line on the one hand and the experienced ratio between width and length of the line on the other hand is huge, but apparently so unobtrusive that it has remained unnoticed. The incompatibility between perspective angles and perceived distances casts doubt on evidence for a curved visual space that has been presented in the literature and was obtained from combining judgments of distances and angles with physical positions. PMID:26034567

100-Lb(f) LO2/LCH4 Reaction Control Engine Technology Development for Future Space Vehicles

NASA Technical Reports Server (NTRS)

Robinson, Philip J.; Veith, Eric M.; Hurlbert, Eric A.; Jimenez, Rafael; Smith, Timothy D.

2008-01-01

The National Aeronautics and Space Administration (NASA) has identified liquid oxygen (LO2)/liquid methane (LCH4) propulsion systems as promising options for some future space vehicles. NASA issued a contract to Aerojet to develop a 100-lbf (445 N) LO2/LCH4 Reaction Control Engine (RCE) aimed at reducing the risk of utilizing a cryogenic reaction control system (RCS) on a space vehicle. Aerojet utilized innovative design solutions to develop an RCE that can ignite reliably over a broad range of inlet temperatures, perform short minimum impulse bits (MIB) at small electrical pulse widths (EPW), and produce excellent specific impulse (Isp) across a range of engine mixture ratios (MR). These design innovations also provide a start transient with a benign MR, ensuring good thrust chamber compatibility and long life. In addition, this RCE can successfully operate at MRs associated with main engines, enabling the RCE to provide emergency backup propulsion to minimize vehicle propellant load and overall system mass.

100-LBF LO2/LCH4 - Reaction Control Engine Technology Development for Future Space Vehicles

NASA Technical Reports Server (NTRS)

Robinson, Philip J.; Veith, Eric M.; Hurlbert, Eric A.; Jimenez, Rafael; Smith, Timothy D.

2008-01-01

The National Aeronautics and Space Administration (NASA) has identified liquid oxygen (LO2)/liquid methane (LCH4) propulsion systems as promising options for some future space vehicles. NASA issued a contract to Aerojet to develop a 100-lbf (445 N) LO2/LCH4 Reaction Control Engine (RCE) aimed at reducing the risk of utilizing a cryogenic reaction control system (RCS) on a space vehicle. Aerojet utilized innovative design solutions to develop an RCE that can ignite reliably over a broad range of inlet temperatures, perform short minimum impulse bits (MIB) at small electrical pulse widths (EPW), and produce excellent specific impulse (Isp) across a range of engine mixture ratios (MR). These design innovations also provide a start transient with a benign MR, ensuring good thrust chamber compatibility and long life. In addition, this RCE can successfully operate at MRs associated with main engines, enabling the RCE to provide emergency backup propulsion to minimize vehicle propellant load and overall system mass.

Phage-bacteria infection networks: From nestedness to modularity

NASA Astrophysics Data System (ADS)

Flores, Cesar O.; Valverde, Sergi; Weitz, Joshua S.

2013-03-01

Bacteriophages (viruses that infect bacteria) are the most abundant biological life-forms on Earth. However, very little is known regarding the structure of phage-bacteria infections. In a recent study we re-evaluated 38 prior studies and demonstrated that phage-bacteria infection networks tend to be statistically nested in small scale communities (Flores et al 2011). Nestedness is consistent with a hierarchy of infection and resistance within phages and bacteria, respectively. However, we predicted that at large scales, phage-bacteria infection networks should be typified by a modular structure. We evaluate and confirm this hypothesis using the most extensive study of phage-bacteria infections (Moebus and Nattkemper 1981). In this study, cross-infections were evaluated between 215 marine phages and 286 marine bacteria. We develop a novel multi-scale network analysis and find that the Moebus and Nattkemper (1981) study, is highly modular (at the whole network scale), yet also exhibits nestedness and modularity at the within-module scale. We examine the role of geography in driving these modular patterns and find evidence that phage-bacteria interactions can exhibit strong similarity despite large distances between sites. CFG acknowledges the support of CONACyT Foundation. JSW holds a Career Award at the Scientific Interface from the Burroughs Wellcome Fund and acknowledges the support of the James S. McDonnell Foundation

On Applications of Disruption Tolerant Networking to Optical Networking in Space

NASA Technical Reports Server (NTRS)

Hylton, Alan Guy; Raible, Daniel E.; Juergens, Jeffrey; Iannicca, Dennis

2012-01-01

The integration of optical communication links into space networks via Disruption Tolerant Networking (DTN) is a largely unexplored area of research. Building on successful foundational work accomplished at JPL, we discuss a multi-hop multi-path network featuring optical links. The experimental test bed is constructed at the NASA Glenn Research Center featuring multiple Ethernet-to-fiber converters coupled with free space optical (FSO) communication channels. The test bed architecture models communication paths from deployed Mars assets to the deep space network (DSN) and finally to the mission operations center (MOC). Reliable versus unreliable communication methods are investigated and discussed; including reliable transport protocols, custody transfer, and fragmentation. Potential commercial applications may include an optical communications infrastructure deployment to support developing nations and remote areas, which are unburdened with supporting an existing heritage means of telecommunications. Narrow laser beam widths and control of polarization states offer inherent physical layer security benefits with optical communications over RF solutions. This paper explores whether or not DTN is appropriate for space-based optical networks, optimal payload sizes, reliability, and a discussion on security.

Cryo-transmission electron microscopy of frozen-hydrated sections of Escherichia coli and Pseudomonas aeruginosa.

PubMed

Matias, Valério R F; Al-Amoudi, Ashraf; Dubochet, Jacques; Beveridge, Terry J

2003-10-01

High-pressure freezing of Escherichia coli K-12 and Pseudomonas aeruginosa PAO1 in the presence of cryoprotectants provided consistent vitrification of cells so that frozen-hydrated sections could be cut, providing approximately 2-nm resolution of structure. The size and shape of the bacteria, as well as their surface and cytoplasmic constituents, were nicely preserved and compared well with other published high-resolution techniques. Cells possessed a rich cytoplasm containing a diffuse dispersion of ribosomes and genetic material. Close examination of cells revealed that the periplasmic space was compressed during cryosectioning, a finding which provided supporting evidence that this space is filled by a compressible gel. Since the outer membrane and peptidoglycan layer are bonded together via lipoproteins, the space between them (although still part of the periplasmic space) was not as compacted. Even when this cryosectioning compression was taken into account, there was still substantial variability in the width of the periplasmic space. It is possible that the protoplast has some capacity to float freely within the periplasm.

Two-dimensional relativistic space charge limited current flow in the drift space

NASA Astrophysics Data System (ADS)

Liu, Y. L.; Chen, S. H.; Koh, W. S.; Ang, L. K.

2014-04-01

Relativistic two-dimensional (2D) electrostatic (ES) formulations have been derived for studying the steady-state space charge limited (SCL) current flow of a finite width W in a drift space with a gap distance D. The theoretical analyses show that the 2D SCL current density in terms of the 1D SCL current density monotonically increases with D/W, and the theory recovers the 1D classical Child-Langmuir law in the drift space under the approximation of uniform charge density in the transverse direction. A 2D static model has also been constructed to study the dynamical behaviors of the current flow with current density exceeding the SCL current density, and the static theory for evaluating the transmitted current fraction and minimum potential position have been verified by using 2D ES particle-in-cell simulation. The results show the 2D SCL current density is mainly determined by the geometrical effects, but the dynamical behaviors of the current flow are mainly determined by the relativistic effect at the current density exceeding the SCL current density.

A Method to Overcome Space Charge at Injection

NASA Astrophysics Data System (ADS)

Derbenev, Ya.

2005-06-01

The transverse space charge forces in a high current, low energy beam can be reduced by mean of a large increase of the beam's transverse sizes while maintaining the beam area in the 4D phase space. This can be achieved by transforming the beam area in phase space of each of two normal 2D transverse (either plane or circular) modes from a spot shape into a narrow ring of a large amplitude, but homogeneous in phase. Such a transformation results from the beam evolution in the island of a dipole resonance when the amplitude width of the island shrinks adiabatically. After stacking (by using stripping foils or cooling) the beam in such a state and accelerating to energies sufficiently high that the space charge becomes insignificant, the beam then can be returned back to a normal spot shape by applying the reverse transformation. An arrangement that can provide such beam gymnastics along a transport line after a linac and before a booster and/or in a ring with circulating beam will be described and numerical estimates will be presented. Other potential applications of the method will be briefly discussed.

Street choice logit model for visitors in shopping districts.

PubMed

Kawada, Ko; Yamada, Takashi; Kishimoto, Tatsuya

2014-09-01

In this study, we propose two models for predicting people's activity. The first model is the pedestrian distribution prediction (or postdiction) model by multiple regression analysis using space syntax indices of urban fabric and people distribution data obtained from a field survey. The second model is a street choice model for visitors using multinomial logit model. We performed a questionnaire survey on the field to investigate the strolling routes of 46 visitors and obtained a total of 1211 street choices in their routes. We proposed a utility function, sum of weighted space syntax indices, and other indices, and estimated the parameters for weights on the basis of maximum likelihood. These models consider both street networks, distance from destination, direction of the street choice and other spatial compositions (numbers of pedestrians, cars, shops, and elevation). The first model explains the characteristics of the street where many people tend to walk or stay. The second model explains the mechanism underlying the street choice of visitors and clarifies the differences in the weights of street choice parameters among the various attributes, such as gender, existence of destinations, number of people, etc. For all the attributes considered, the influences of DISTANCE and DIRECTION are strong. On the other hand, the influences of Int.V, SHOPS, CARS, ELEVATION, and WIDTH are different for each attribute. People with defined destinations tend to choose streets that "have more shops, and are wider and lower". In contrast, people with undefined destinations tend to choose streets of high Int.V. The choice of males is affected by Int.V, SHOPS, WIDTH (positive) and CARS (negative). Females prefer streets that have many shops, and couples tend to choose downhill streets. The behavior of individual persons is affected by all variables. The behavior of people visiting in groups is affected by SHOP and WIDTH (positive).

Street Choice Logit Model for Visitors in Shopping Districts

PubMed Central

Kawada, Ko; Yamada, Takashi; Kishimoto, Tatsuya

2014-01-01

In this study, we propose two models for predicting people’s activity. The first model is the pedestrian distribution prediction (or postdiction) model by multiple regression analysis using space syntax indices of urban fabric and people distribution data obtained from a field survey. The second model is a street choice model for visitors using multinomial logit model. We performed a questionnaire survey on the field to investigate the strolling routes of 46 visitors and obtained a total of 1211 street choices in their routes. We proposed a utility function, sum of weighted space syntax indices, and other indices, and estimated the parameters for weights on the basis of maximum likelihood. These models consider both street networks, distance from destination, direction of the street choice and other spatial compositions (numbers of pedestrians, cars, shops, and elevation). The first model explains the characteristics of the street where many people tend to walk or stay. The second model explains the mechanism underlying the street choice of visitors and clarifies the differences in the weights of street choice parameters among the various attributes, such as gender, existence of destinations, number of people, etc. For all the attributes considered, the influences of DISTANCE and DIRECTION are strong. On the other hand, the influences of Int.V, SHOPS, CARS, ELEVATION, and WIDTH are different for each attribute. People with defined destinations tend to choose streets that “have more shops, and are wider and lower”. In contrast, people with undefined destinations tend to choose streets of high Int.V. The choice of males is affected by Int.V, SHOPS, WIDTH (positive) and CARS (negative). Females prefer streets that have many shops, and couples tend to choose downhill streets. The behavior of individual persons is affected by all variables. The behavior of people visiting in groups is affected by SHOP and WIDTH (positive). PMID:25379274

Prognostic Factors in the Midterm Results of Pullout Fixation for Posterior Root Tears of the Medial Meniscus.

PubMed

Chung, Kyu Sung; Ha, Jeong Ku; Ra, Ho Jong; Kim, Jin Goo

2016-07-01

To identify predictors of unfavorable clinical and radiologic outcomes a minimum of 5 years after pullout fixation for medial meniscus posterior root tears (MMPRTs). In total, 40 patients who were followed for >5 years after pullout fixation in MMPRT were recruited. The mean follow-up duration was 71.1 months. Clinical outcomes, including Lysholm score and International Knee Documentation Committee (IKDC) score, and radiographic results, including Kellgren-Lawrence (K-L; 0/1/2/3/4) grade and medial joint space width, were evaluated preoperatively and at final follow-up. Preoperative prognostic factors, including age, sex, body mass index, degree of varus alignment, K-L grade, medial joint space width, meniscal extrusion, and cartilage status, by the modified Outerbridge classification (grades 1 or 2 v 3 or 4), for relatively unfavorable (fair or poor grade) Lysholm or IKDC score, and progression of K-L grade were investigated by multivariate logistic regression analysis. The mean Lysholm score (52.1 ± 8.8 to 83.8 ± 11.9) and IKDC score (40.1 ± 7.6 to 73.3 ± 10.9) were improved significantly (P < .001), although the loss of medial joint space width (4.8 ± 1.1 to 3.9 ± 1.1 mm) and K-L grade (6/25/9/0/0 to 0/11/20/9/0) progressed significantly (P < .001). Unfavorable prognostic factors of the Lysholm score were grade ≥3 chondral lesions (odds ratio [OR] = 5.993; P = .028) and varus mechanical alignment (OR = 1.644; P = .017), for IKDC score were grade ≥3 chondral lesions (OR = 11.146; P = .038) and older age (OR = 1.200; P = .017). Preoperative chondral lesion grade ≥3 increased the risk of K-L grade progression (OR = 11.000; P = .031). Clinically, modified Outerbridge classification grade ≥3 chondral lesions, varus alignment, and older age were found to predict a poor prognosis after MMPRT fixation. In terms of radiographic K-L grade progression, grade ≥3 chondral lesions were identified as a poor prognostic factor. Level IV, case series. Copyright © 2016 Arthroscopy Association of North America. Published by Elsevier Inc. All rights reserved.

Morphology and spacing of river meander scrolls

NASA Astrophysics Data System (ADS)

Strick, Robert J. P.; Ashworth, Philip J.; Awcock, Graeme; Lewin, John

2018-06-01

Many of the world's alluvial rivers are characterised by single or multiple channels that are often sinuous and that migrate to produce a mosaicked floodplain landscape of truncated scroll (or point) bars. Surprisingly little is known about the morphology and geometry of scroll bars despite increasing interest from hydrocarbon geoscientists working with ancient large meandering river deposits. This paper uses remote sensing imagery, LiDAR data-sets of meandering scroll bar topography, and global coverage elevation data to quantify scroll bar geometry, anatomy, relief, and spacing. The analysis focuses on preserved scroll bars in the Mississippi River (USA) floodplain but also compares attributes to 19 rivers of different scale and depositional environments from around the world. Analysis of 10 large scroll bars (median area = 25 km2) on the Mississippi shows that the point bar deposits can be categorised into three different geomorphological units of increasing scale: individual 'scrolls', 'depositional packages', and 'point bar complexes'. Scroll heights and curvatures are greatest near the modern channel and at the terminating boundaries of different depositional packages, confirming the importance of the formative main channel on subsequent scroll bar relief and shape. Fourier analysis shows a periodic variation in signal (scroll bar height) with an average period (spacing) of 167 m (range 150-190 m) for the Mississippi point bars. For other rivers, a strong relationship exists between the period of scroll bars and the adjacent primary channel width for a range of rivers from 55 to 2042 mis 50% of the main channel width. The strength of this correlation over nearly two orders of magnitude of channel size indicates a scale independence of scroll bar spacing and suggests a strong link between channel migration and scroll bar construction with apparent regularities despite different flow regimes. This investigation of meandering river dynamics and floodplain patterns shows that it is possible to develop a suite of metrics that describe scroll bar morphology and geometry that can be valuable to geoscientists predicting the heterogeneity of subsurface meandering deposits.

Normal radiological unossified hip joint space and femoral head size development during growth in 675 children and adolescents.

PubMed

Wegener, Veronika; Jorysz, Gabriele; Arnoldi, Andreas; Utzschneider, Sandra; Wegener, Bernd; Jansson, Volkmar; Heimkes, Bernhard

2017-03-01

Evaluation of hip joint space width during child growth is important to aid in the early diagnosis of hip pathology in children. We established reference values for hip joint space and femoral head size for each age. Hip joint space development during growth was retrospectively investigated medial and cranial in 1350 hip joints of children using standard anteroposterior supine plain pelvic radiographs. Maximum capital femoral epiphysis diameter and femoral radii were further more investigated. Hip joint space values show a slow decline during growth. Joint space was statistically significantly (p < 0.006) larger in boys than girls. Our hip joint space measurements on supine subjects seem slightly larger than those reported by Hughes on standing subjects. Evaluation of the femoral head diameter and the radii showed a size curve quite parallel to the known body growth charts. Radii medial and perpendicular to the physis are not statistically significantly different. We recommend to compare measurements of hip joint space at two locations to age dependent charts using the same imaging technique. During growth, a divergence in femoral head size from the expected values or loss of the spherical shape should raise the question of hip disorder. Clin. Anat. 30:267-275, 2017. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

Molecular Simulation Results on Charged Carbon Nanotube Forest-Based Supercapacitors.

PubMed

Muralidharan, Ajay; Pratt, Lawrence R; Hoffman, Gary G; Chaudhari, Mangesh I; Rempe, Susan B

2018-06-22

Electrochemical double-layer capacitances of charged carbon nanotube (CNT) forests with tetraethyl ammonium tetrafluoro borate electrolyte in propylene carbonate are studied on the basis of molecular dynamics simulation. Direct molecular simulation of the filling of pore spaces of the forest is feasible even with realistic, small CNT spacings. The numerical solution of the Poisson equation based on the extracted average charge densities then yields a regular experimental dependence on the width of the pore spaces, in contrast to the anomalous pattern observed in experiments on other carbon materials and also in simulations on planar slot-like pores. The capacitances obtained have realistic magnitudes but are insensitive to electric potential differences between the electrodes in this model. This agrees with previous calculations on CNT forest supercapacitors, but not with experiments which have suggested electrochemical doping for these systems. Those phenomena remain for further theory/modeling work. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Solitary Potential in a Space Plasma Containing Dynamical Heavy Ions and Bi-Kappa Distributed Electrons of Two Distinct Temperatures

NASA Astrophysics Data System (ADS)

Sarker, M.; Hosen, B.; Hossen, M. R.; Mamun, A. A.

2018-01-01

The heavy ion-acoustic solitary waves (HIASWs) in a magnetized, collisionless, space plasma system (containing dynamical heavy ions and bi-kappa distributed electrons of two distinct temperatures) have been theoretically investigated. The Korteweg-de Vries (K-dV), modified K-dV (MK-dV), and higher-order MK-dV (HMK-dV) equations are derived by employing the reductive perturbation method. The basic features of HIASWs (viz. speed, polarity, amplitude, width, etc.) are found to be significantly modified by the effects of number density and temperature of different plasma species, and external magnetic field (obliqueness). The K-dV and HM-KdV equations give rise to both compressive and rarefactive solitary structures, whereas the MK-dV equation supports only the compressive solitary structures. The implication of our results in some space and laboratory plasma situations are briefly discussed.

Experimental quantum teleportation over a high-loss free-space channel.

PubMed

Ma, Xiao-song; Kropatschek, Sebastian; Naylor, William; Scheidl, Thomas; Kofler, Johannes; Herbst, Thomas; Zeilinger, Anton; Ursin, Rupert

2012-10-08

We present a high-fidelity quantum teleportation experiment over a high-loss free-space channel between two laboratories. We teleported six states of three mutually unbiased bases and obtained an average state fidelity of 0.82(1), well beyond the classical limit of 2/3. With the obtained data, we tomographically reconstructed the process matrices of quantum teleportation. The free-space channel attenuation of 31 dB corresponds to the estimated attenuation regime for a down-link from a low-earth-orbit satellite to a ground station. We also discussed various important technical issues for future experiments, including the dark counts of single-photon detectors, coincidence-window width etc. Our experiment tested the limit of performing quantum teleportation with state-of-the-art resources. It is an important step towards future satellite-based quantum teleportation and paves the way for establishing a worldwide quantum communication network.

Fabrication of polydimethylsiloxane (PDMS) nanofluidic chips with controllable channel size and spacing.

PubMed

Peng, Ran; Li, Dongqing

2016-10-07

The ability to create reproducible and inexpensive nanofluidic chips is essential to the fundamental research and applications of nanofluidics. This paper presents a novel and cost-effective method for fabricating a single nanochannel or multiple nanochannels in PDMS chips with controllable channel size and spacing. Single nanocracks or nanocrack arrays, positioned by artificial defects, are first generated on a polystyrene surface with controllable size and spacing by a solvent-induced method. Two sets of optimal working parameters are developed to replicate the nanocracks onto the polymer layers to form the nanochannel molds. The nanochannel molds are used to make the bi-layer PDMS microchannel-nanochannel chips by simple soft lithography. An alignment system is developed for bonding the nanofluidic chips under an optical microscope. Using this method, high quality PDMS nanofluidic chips with a single nanochannel or multiple nanochannels of sub-100 nm width and height and centimeter length can be obtained with high repeatability.

Measurement of sea ice backscatter characteristics at 36 GHz using the surface contour radar

NASA Technical Reports Server (NTRS)

Fedor, L. S.; Walsh, E. J.

1985-01-01

Scattering studies of sea ice off the coast of Greenland were performed in January 1984 using the 36-GHz Surface Contour Radar (SCR) aboard the NASA P-3 aircraft. An oscillating mirror scans an actual half-power width of 0.96 degrees laterally to measure the surface at 51 evenly spaced points. By banking the aircraft, real-time topographical mapping and relative backscattered power are obtained at incidence angles between 0 and 30 degrees off-nadar, achieving at 175 m altitude a 2.9 by 4.4 m spatial resolution at nadir. With an aircraft ground speed of 100 m/s, 5-m successive scan line spacing and 1.8-m cross-track direction spacing is provided. By circling the aircraft in the 15 degree bank, the azimuthal anisotropy of the scattering is investigated along with the incidence angle dependence.

Extraction of MOS VLSI (Very-Large-Scale-Integrated) Circuit Models Including Critical Interconnect Parasitics.

DTIC Science & Technology

1987-09-01

can be reduced substantially, compared to using numerical methods to model inter - " connect parasitics. Although some accuracy might be lost with...conductor widths and spacings listed in Table 2 1 , have been employed for simulation. In the first set of the simulations, planar dielectric inter ...model, there are no restrictions on the iumber ol diele-iric and conductors. andl the shape of the conductors and the dielectric inter - a.e,, In the

Seaworthy Quantum Key Distribution Design and Validation (SEAKEY)

DTIC Science & Technology

2014-07-25

link in a free- space channel through a marine environment (such as loss, noise and turbulence) and (2) parametrically calculating the secret key rate...width. Parametric calculations of the expected secret key rate As can be seen in Figure 6, the secret key rate of the BB84 protocol in the presence...Figure 9 shows the effect of various detriments on the secret -kay rate, for laser-decoy BB84. Figure 9: Effects of detriments on secret-key rate

Ring formation in self-focusing of electromagnetic beams in plasmas

NASA Astrophysics Data System (ADS)

Faisal, M.; Mishra, S. K.; Verma, M. P.; Sodha, M. S.

2007-10-01

This article presents a paraxial theory of ring formation as an initially Gaussian beam propagates in a nonlinear plasma, characterized by significant collisional or ponderomotive nonlinearity. Regions in the axial irradiance-(beamwidth)-2 space, for which the ring formation occurs and the paraxial theory is valid, have been characterized; for typical points in these regions the dependence of the beam width parameter and the radial distribution of irradiance on the distance has been specifically investigated and discussed.

Analysis of EUVE Experiment Results

NASA Technical Reports Server (NTRS)

Horan, Stephen

1996-01-01

A series of tests to validate an antenna pointing concept for spin-stabilized satellites using a data relay satellite are described. These tests show that proper antenna pointing on an inertially-stabilized spacecraft can lead to significant access time through the relay satellite even without active antenna pointing. We summarize the test results, the simulations to model the effects of antenna pattern and space loss, and the expected contact times. We also show how antenna beam width affects the results.

The One-Pot Directed Assembly of Cylinder-Forming Block Copolymer on Adjacent Chemical Patterns for Bimodal Patterning.

PubMed

Chang, Tzu-Hsuan; Xiong, Shisheng; Liu, Chi-Chun; Liu, Dong; Nealey, Paul F; Ma, Zhenqiang

2017-09-01

The direct self-assembly of cylinder-forming poly(styrene-block-methyl-methacrylate) (PS-b-PMMA) block copolymer is successfully assembled into two orientations, according to the underlying guiding pattern in different areas. Lying-down and perpendicular cylinders are formed, respectively, depending on the design of chemical pattern: sparse line/space pattern or hexagonal dot array. The first chemical pattern composed of prepatterned cross-linked polystyrene (XPS) line/space structure has a period (L S ) equal to twice the intercylinder period of the block copolymer (L 0 ). The PS-b-PMMA thin film on the prepared chemical template after thermal annealing forms a lying-down cylinder morphology when the width of the PS strips is less than the width of PS block in the PS-b-PMMA block copolymer. The morphology is only applicable at the discrete thickness of the PS-b-PMMA film. In addition to forming the lying-down cylinders directly on the XPS guiding pattern, the cylinder-forming block copolymer can also be assembled in a perpendicular way on the second guiding pattern (the hexagonal dot array). The block copolymer films are registered into two orientations in a single directed self-assembly process. The features of the assembled patterns are successfully transferred down to the silicon oxide substrate. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A new parallel plate shear cell for in situ real-space measurements of complex fluids under shear flow.

PubMed

Wu, Yu Ling; Brand, Joost H J; van Gemert, Josephus L A; Verkerk, Jaap; Wisman, Hans; van Blaaderen, Alfons; Imhof, Arnout

2007-10-01

We developed and tested a parallel plate shear cell that can be mounted on top of an inverted microscope to perform confocal real-space measurements on complex fluids under shear. To follow structural changes in time, a plane of zero velocity is created by letting the plates move in opposite directions. The location of this plane is varied by changing the relative velocities of the plates. The gap width is variable between 20 and 200 microm with parallelism better than 1 microm. Such a small gap width enables us to examine the total sample thickness using high numerical aperture objective lenses. The achieved shear rates cover the range of 0.02-10(3) s(-1). This shear cell can apply an oscillatory shear with adjustable amplitude and frequency. The maximum travel of each plate equals 1 cm, so that strains up to 500 can be applied. For most complex fluids, an oscillatory shear with such a large amplitude can be regarded as a continuous shear. We measured the flow profile of a suspension of silica colloids in this shear cell. It was linear except for a small deviation caused by sedimentation. To demonstrate the excellent performance and capabilities of this new setup we examined shear induced crystallization and melting of concentrated suspensions of 1 microm diameter silica colloids.

Insects traversing grass-like vertical compliant beams

NASA Astrophysics Data System (ADS)

Li, Chen; Fearing, Ronald; Full, Robert

2014-03-01

Small running animals encounter many challenging terrains. These terrains can be filled with 3D, multi-component obstacles. Here, we study cockroaches (Blaberus discoidalis) moving through grass-like vertical compliant beams during escape. We created an apparatus to control and vary geometric parameters and mechanical properties of model grass including height, width, thickness, lateral and fore-aft spacings, angle, number of layers, stiffness, and damping. We observed a suite of novel locomotor behaviors not previously described on simpler 2D ground. When model grass height was >2 × body length and lateral spacing was <0.5 × body width, the animal primarily (probability P = 50%) rolled its body onto its side to rapidly (time t = 2.1 s) maneuver through the gaps between model grass. We developed a simple energy minimization model, and found that body roll reduces the energy barriers that the animal must overcome during traversal. We hypothesized that the animal's ellipsoidal body shape facilitated traversal. To test our hypothesis, we modified body shape by adding either a rectangular or an oval plate onto its dorsal surface, and found that P dropped by an order of magnitude and t more than doubled. Upon removal of either plate, both P and t recovered. Locomotor kinematics and geometry effectively coupled to terrain properties enables negotiation of 3D, multi-component obstacles, and provides inspiration for small robots to navigate such terrain with minimal sensing and control.

Lineshapes of Dipole-Dipole Resonances in a Cold Rydberg Gas

NASA Astrophysics Data System (ADS)

Richards, B. G.; Jones, R. R.

2015-05-01

We have examined the lineshapes associated with Stark tuned, dipole-dipole resonances involving Rydberg atoms in a cold gas. Rb atoms in a MOT are laser excited from the 5 p level to 32p3 / 2 in the presence of a weak electric field. A fast rising electric field pulse Stark tunes the total energy of two 32 p atom pairs so it is (nearly) degenerate with that of the 32s1 / 2+33s1 / 2 states. Because of the dipole-dipole coupling, atom pairs separated by a distance R, develop 32s1 / 2+33s1 / 2 character. The maximum probability for finding atoms in s-states depends on the detuning from degeneracy and on the dipole-dipole coupling. We obtain the ``resonance'' lineshape by measuring, via state-selective field ionization, the s-state population as a function of the tuning field. The resonance width decreases with density due to R-3 dependence of the dipole-dipole coupling. In principle, the lineshape provides information about the distribution of Rydberg atom spacings in the sample. For equally spaced atoms, the lineshape should be Lorentzian while for a random nearest neighbor distribution it appears as a cusp. At low densities nearly Gaussian lineshapes are observed with widths that are too large to be the result of inhomogeneous electric or magnetic fields. Supported by the NSF.

Direct Printing of 1-D and 2-D Electronically Conductive Structures by Molten Lead-Free Solder

PubMed Central

Wang, Chien-Hsun; Tsai, Ho-Lin; Hwang, Weng-Sing

2016-01-01

This study aims to determine the effects of appropriate experimental parameters on the thermophysical properties of molten micro droplets, Sn-3Ag-0.5Cu solder balls with an average droplet diameter of 50 μm were prepared. The inkjet printing parameters of the molten micro droplets, such as the dot spacing, stage velocity and sample temperature, were optimized in the 1D and 2D printing of metallic microstructures. The impact and mergence of molten micro droplets were observed with a high-speed digital camera. The line width of each sample was then calculated using a formula over a temperature range of 30 to 70 °C. The results showed that a metallic line with a width of 55 μm can be successfully printed with dot spacing (50 μm) and the stage velocity (50 mm∙s−1) at the substrate temperature of 30 °C. The experimental results revealed that the height (from 0.63 to 0.58) and solidification contact angle (from 72° to 56°) of the metallic micro droplets decreased as the temperature of the sample increased from 30 to 70 °C. High-speed digital camera (HSDC) observations showed that the quality of the 3D micro patterns improved significantly when the droplets were deposited at 70 °C. PMID:28772361

[Microclimate and comfortable degree of Shanghai urban open spaces in summer].

PubMed

Cao, Dan; Zhou, Li-chen; Mao, Yi-wei; Li, Yin; Liu, Yi-ning; Wang, Tian-hou

2008-08-01

Based on the observation data of air temperature, relative humidity, wind speed, and solar radiation from May to August 2006, the regulation effects of five types of open spaces (square, fountain, grassplot, corridor, and woodland) in Shanghai urban districts on the microclimate were analyzed, and discomfort index (DI) was introduced to evaluate the effects of these five types of open spaces on human body' s comfortable degree. The results showed that there existed definite differences in the air temperature and relative humidity among the open spaces, with the mean temperature decreased in the order of square > grassplot > fountain > corridor > woodland, and the mean relative humidity decreased in the order of woodland > corridor > fountain > grassplot > square. The area of the square, the wind speed and direction near the fountain, the grass species on the grass-plot, the width and tree coverage of the corridor, and the tree coverage and canopy height of the woodland had significant correlations with the microclimate parameters of corresponding open spaces. Comparing with other three types of open spaces, woodland and corridor had better regulation effects on the microclimate via shading, decreasing air temperature, and increasing relative humidity.

History of Hubble Space Telescope (HST)

NASA Image and Video Library

1990-04-25

In this photograph, the Hubble Space Telescope (HST) was being deployed on April 25, 1990. The photograph was taken by the IMAX Cargo Bay Camera (ICBC) mounted in a container on the port side of the Space Shuttle orbiter Discovery (STS-31 mission). The purpose of the HST, the most complex and sensitive optical telescope ever made, is to study the cosmos from a low-Earth orbit for 15 years or more. The HST provides fine detail imaging, produces ultraviolet images and spectra, and detects very faint objects. Two months after its deployment in space, scientists detected a 2-micron spherical aberration in the primary mirror of the HST that affected the telescope's ability to focus faint light sources into a precise point. This imperfection was very slight, one-fiftieth of the width of a human hair. A scheduled Space Service servicing mission (STS-61) in 1993 permitted scientists to correct the problem. During four spacewalks, new instruments were installed into the HST that had optical corrections. The Marshall Space Flight Center had responsibility for design, development, and construction of the HST. The Perkin-Elmer Corporation, in Danbury, Cornecticut, developed the optical system and guidance sensors. Photo Credit: NASA/Smithsonian Institution/Lockheed Corporation.

Electrons and proton transfer in chloroplasts in silico: 1. The effect of topological factors on energy coupling in chloroplasts with a nonuniform distribution of protein complexes

NASA Astrophysics Data System (ADS)

Vershubskii, A. V.; Tikhonov, A. N.

2017-05-01

This paper presents a theoretical study of the effects of topological factors (density of thylakoid packing in grana) on the efficiency of energy coupling in chloroplasts. The study is based on a mathematical model of electron and proton transport processes coupled to ATP synthesis in chloroplasts. The model was developed by the authors earlier, and the nonuniform distribution of electron transport and ATP synthase complexes in the membranes of granal and intergranal thylakoids was taken into account in the model. The results of numerical experiments enabled the analysis of the distribution of lateral profiles of the transmembrane pH difference and the concentrations of mobile plastoquinone and plastocyanin electron transporters in granal and intergranal thylakoids and the dependence of this distribution on the metabolic state of class B chloroplasts (photosynthetic control state or the conditions of intensive ATP synthesis). Moreover, the influence of topological factors (the density of thylakoid packing in grana and the degree of thylakoid swelling) that affect the rate of diffusion of protons and mobile electron carriers in the intrathylakoid space and in the interthylakoidal gap was investigated. The results of numerical experiments that involved the variation of geometric parameters of the system revealed the influence of thylakoid thickness and the distance between the granal thylakoids on the lateral pH profiles inside the thylakoids (pHi) and in the interthylakoidal gap (pHo). Acidification of the intrathylakoid space characterized by the pHi value increased concomitantly to the increase of the width of the interthylakoidal gap l o and decreased concomitantly to the increase of the width of the intrathylakoidal space l i.

Chondroprotection using naturally occurring mineral supplementation formula in degenerative osteoarthritis of the knees.

PubMed

Bansal, Himanshu; Bansal, Anupama; Agrawal, Diwaker; Singh, Dhananjay; Deb, Kaushik

2014-01-01

To evaluate the therapeutic and safety efficacy of a naturally occurring mineral supplementation in the treatment of symptomatic knee osteoarthritis (OA). A prospective, single centre, study of 50 patients aged 50 years and above with painful and radiological Osteoarthritis of knees was carried out for one year. Patients received 40 drops of naturally occurring commercially available mineral supplement concentrate mineral drops purportedly derived from the Great Salt Lake in Utah. Efficacy was objectively confirmed by evaluating changes in the thickness of articular cartilage, joint space width, synovial fluid analysis and subjectively by changes in WOMAC scores and 6 Minute pain-free Walking Distance. The composite WOMAC scores were significantly improved by 17.2 points from a mean of 52 at baseline by year end. 18 (41%) patients showed improvement of more than 100 feet for the pain free distance covered during a 6 minute walk at one year follow-up. Ultrasonologicaly, at one year cartilage thickness improved by at least 0.01 mm in 9 (21%) patients. Though radiologicallynone of patient showed increase in joint space it was noticed that only 2(4.6%) patients had decline of joint space width of more than 0.5 mm. Average cell count reduced to 205/microlitre from a value of 520/microlitre at the start of study suggesting that the mineral supplement used had structural efficacy. Clinically relevant, statistically significant symptomatic and statistically insignificant structural improvement occurred over 1 year period in patients receiving the naturally occurring mineral supplement. The protection of the joint cartilages from progressive degeneration during osteoarthritis by these supplements indicates towards a chondrocyte regenerative potential of this supplement. Such regeneration may occur through activation of tissue specific adult chondrocyte precursors or stem cells.

Trophic ecology and gill raker morphology of seven catostomid species in Iowa rivers

USGS Publications Warehouse

Spiegel, J.R.; Quist, M.C.; Morris, J.E.

2011-01-01

Understanding the trophic ecology of closely-related species is important for providing insight on inter-specific competition and resource partitioning. Although catostomids often dominate fish assemblages in lotic systems, little research has been conducted on their ecology. This study was developed to provide information on the trophic ecology of catostomids in several Iowa rivers. Food habits, diet overlap, and gill raker morphology were examined for highfin carpsucker Carpiodes velifer, quillback C.??cyprinus, river carpsucker C.??carpio, golden redhorse Moxostoma erythrurum, shorthead redhorse M.??macrolepidotum, silver redhorse M.??anisurum, and northern hogsucker Hypentelium nigricans sampled from four Iowa rivers (2009). Diet overlap among all species was calculated with Morista's index (C). Food habit niche width was quantified with Levin's index (B) and similarity in gill raker morphology was compared with analysis of covariance. Values from Morista's index suggested significant overlap in the diets of highfin carpsucker and river carpsucker (C=0.81), quillback and river carpsucker (C=0.66), and shorthead redhorse and silver redhorse (C=0.67). Levin's index indicated that golden redhorse (B=0.32), quillback (B=0.53), and river carpsucker (B=0.41) had the most generalized feeding strategies as their food niche widths were substantially wider than the other species. Gill raker length and spacing were positively correlated with the standard length of the fish for all species (gill raker length: r2=0.67-0.88, P???0.01; gill raker spacing: r2=0.63-0.73, P???0.01). Slopes of regression of gill raker length and spacing to standard lengths were significantly (P???0.05) different among species, indicating that rates of change in gill raker morphology with body length varied among species. Differences in gill raker morphology likely allow catostomids to partition resources and reduce competitive interactions. ?? 2011.

Cartilage Thickening in Early Radiographic Human Knee Osteoarthritis –Within-Person, Between-Knee Comparison

PubMed Central

Cotofana, Sebastian; Buck, Robert; Wirth, Wolfgang; Roemer, Frank; Duryea, Jeff; Nevitt, Michael; Eckstein, Felix

2012-01-01

Objective To determine whether the presence of definite osteophytes (in absence of joint space narrowing [JSN]) by radiograph is associated with (subregional) increases in cartilage thickness, in a within-person, between-knee cross-sectional comparison of participants in the Osteoarthritis Initiative (OAI). Based on previous results, external medial (ecMF) and external lateral weight-bearing femoral (ecLF) subregions were selected as primary endpoints. Methods Both knees of 61 (of 4798) OAI participants displayed definite tibial or femoral marginal osteophytes and no JSN in one knee, and no signs of radiographic OA in the contra-lateral knee; this being confirmed by an expert central reader. In these participants, cartilage thickness was measured in 16 femorotibial subregions of each knee, based on sagittal DESSwe magnetic resonance images. Location-specific joint space width from fixed flexion radiographs was determined using dedicated software. Location-specific associations of osteophytes with cartilage thickness were evaluated using paired t-tests and mixed effect models. Results Of the 61 participants, 48% had only medial, 36% only lateral, and 16% bi-compartmental osteophytes. Osteophyte knees had significantly thicker cartilage than contra-lateral non-osteophyte knees in the ecMF (+71±223μm, equivalent to +5.5%, p=0.015) and ecLF (+64±195μm, +4.1%, p=0.013). No significant differences between knees were noted in other subregions, nor in joint space width. Cartilage thickness in ecMF and ecLF was significantly associated with tibial osteophytes in the same (medial or lateral) compartment (p=0.003). Conclusion Knees with early radiographic OA display thicker cartilage than (contra-lateral) knees without radiographic findings of OA, specifically in the external femoral subregions of compartments with marginal osteophytes. PMID:22556039

The Pearson-Readhead Survey of Compact Extragalactic Radio Sources from Space. II. Analysis of Source Properties

NASA Astrophysics Data System (ADS)

Lister, M. L.; Tingay, S. J.; Preston, R. A.

2001-06-01

We have performed a multidimensional correlation analysis on the observed properties of a statistically complete core-selected sample of compact radio-loud active galactic nuclei based on data from the VLBI Space Observing Programme (Paper I) and previously published studies. Our sample is drawn from the well-studied Pearson-Readhead (PR) survey and is ideally suited for investigating the general effects of relativistic beaming in compact radio sources. In addition to confirming many previously known correlations, we have discovered several new trends that lend additional support to the beaming model. These trends suggest that the most highly beamed sources in core-selected samples tend to have (1) high optical polarizations; (2) large parsec- kiloparsec-scale jet misalignments; (3) prominent VLBI core components; (4) one-sided, core, or halo radio morphology on kiloparsec scales; (5) narrow emission line equivalent widths; and (6) a strong tendency for intraday variability at radio wavelengths. We have used higher resolution space and ground-based VLBI maps to confirm the bimodality of the jet misalignment distribution for the PR survey and find that the sources with aligned parsec- and kiloparsec-scale jets generally have arcsecond-scale radio emission on both sides of the core. The aligned sources also have broader emission line widths. We find evidence that the BL Lacertae objects in the PR survey are all highly beamed and have very similar properties to the high optically polarized quasars, with the exception of smaller redshifts. A cluster analysis on our data shows that after partialing out the effects of redshift, the luminosities of our sample objects in various wave bands are generally well correlated with each other but not with other source properties.

Interspecies difference in placement of developing teeth and its relationship with cross-sectional geometry of the mandibular symphysis in four primate species including modern humans.

PubMed

Fukase, Hitoshi

2012-02-01

The form of the anthropoid mandibular symphysis has recently been addressed in association with spatial requirements for the forming anterior teeth. To evaluate potential relationships between the symphyseal shape and teeth further, the growth patterns of the symphyseal region and the positioning of the tooth crypts were examined using CT data, comparing four primate species (modern humans, chimpanzees, Japanese monkeys, and hamadryas baboons) with varied symphyseal curvature and tooth size. First, results showed that interspecies differences in overall mandibular shape including symphyseal inclination and bicanine width are consistently expressed throughout postnatal ontogeny, although local symphyseal configurations related to the superior transverse torus (STT) tended to change considerably during growth in chimpanzees. Second, the four species were found to exhibit differentiated formation positions of the incisor and canine crypts. In particular, I2 developed between I1 and C in humans with a broad bicanine space and small teeth, whereas it was positioned posterior to I1 and above C in the cercopithecines with an extremely narrow bicanine space. In chimpanzees, despite the large bicanine width, I1 and I2 grew with a large antero-posterior overlap owing to their large size. These results indicate that the dental positioning is determined in concert with the size balance of the available mandibular space and forming teeth. Finally, the positions/contours of I2 crypt were shown to correspond strongly with the STT across the taxa. This suggests that interspecies differences in symphyseal shape should be interpreted partially by the species-specific positional relationships of the developing anterior teeth. Copyright © 2011 Wiley Periodicals, Inc.

Exploration of BEOL line-space patterning options at 12 nm half-pitch and below

NASA Astrophysics Data System (ADS)

Decoster, S.; Lazzarino, F.; Petersen Barbosa Lima, L.; Li, W.; Versluijs, J.; Halder, S.; Mallik, A.; Murdoch, G.

2018-03-01

While the semiconductor industry is almost ready for high-volume manufacturing of the 7 nm technology node, research centers are defining and troubleshooting the patterning options for the 5 nm technology node (N5) and below. The target dimension for imec's N5 BEOL applications is 20-24 nm Metal Pitch (MP), which requires Self-Aligned multiple (Double/Quadruple/Octuple) Patterning approaches (SAxP) in combination with EUV or immersion lithography at 193 nm. There are numerous technical challenges to enable gratings at the hard mask level such as good uniformity across wafer, low line edge/width roughness (LER/LWR), large process window, and all of this at low cost. An even greater challenge is to transfer these gratings into the dielectric material at such critical dimensions, where increased line edge roughness, line wiggling and even pattern collapse can be expected for materials with small mechanical stability such as highly porous low-k dielectrics. In this work we first compare three different patterning options for 12 nm half-pitch gratings at the hard mask level: EUV-based SADP and 193i-based SAQP and SAOP. This comparison will be based on process window, line edge/width roughness and cost. Next, the transfer of 12 nm line/space gratings in the dielectric material is discussed and presented. The LER of the dielectric lines is investigated as a function of the dielectric material, the trench depth, and the stress in the sacrificial hard mask. Finally, we elaborate on the different options to enable scaling down from 24 nm MP to 16 nm MP, and demonstrate 8 nm line/space gratings with 193i-based SAOP.

No evidence for Lyman α emission in spectroscopy of z > 7 candidate galaxies

NASA Astrophysics Data System (ADS)

Caruana, Joseph; Bunker, Andrew J.; Wilkins, Stephen M.; Stanway, Elizabeth R.; Lacy, Mark; Jarvis, Matt J.; Lorenzoni, Silvio; Hickey, Samantha

2012-12-01

We present Gemini/Gemini Near Infrared Spectrograph (GNIRS) spectroscopic observations of four z-band (z ≈ 7) dropout galaxies and Very Large Telescope (VLT)/XSHOOTER observations of one z-band dropout and three Y-band (z ≈ 8-9) dropout galaxies in the Hubble Ultra Deep Field, which were selected with Wide Field Camera 3 imaging on the Hubble Space Telescope. We find no evidence of Lyman α emission with a typical 5σ sensitivity of 5 × 10-18 erg cm-2 s-1, and use the upper limits on Lyman α flux and the broad-band magnitudes to constrain the rest-frame equivalent widths for this line emission. Accounting for incomplete spectral coverage, we survey 3.0 z-band dropouts and 2.9 Y-band dropouts to a Lyman α rest-frame equivalent width limit >120 Å (for an unresolved emission line); for an equivalent width limit of 50 Å the effective numbers of drop-outs surveyed fall to 1.2 z-band drop-outs and 1.5 Y-band drop-outs. A simple model where the fraction of high rest-frame equivalent width emitters follows the trend seen at z = 3-6.5 is inconsistent with our non-detections at z = 7-9 at the ≈1σ level for spectrally unresolved lines, which may indicate that a significant neutral H I fraction in the intergalactic medium suppresses the Lyman α line in z-drop and Y-drop galaxies at z > 7. Based on observations collected at the European Organization for Astronomical Research in the Southern Hemisphere, Chile, as part of programme 086.A-0968(B).

Don't Fence Me In: Free Meanders in a Confined River Valley

NASA Astrophysics Data System (ADS)

Eke, E. C.; Wilcock, P. R.

2015-12-01

The interaction between meandering river channels and inerodible valley walls provides a useful test of our ability to understand meander dynamics. In some cases, river meanders confined between valley walls display distinctive angular bends in a dynamic equilibrium such that their size and shape persist as the meander migrates. In other cases, meander geometry is more varied and changes as the meander migrates. The ratio of channel to valley width has been identified as a useful parameter for defining confined meanders, but is not sufficient to distinguish cases in which sharp angular bends are able to migrate with little change in geometry. Here, we examine the effect of water and sediment supply on the geometry of confined rivers in order to identify conditions under which meander geometry reaches a persistent dynamic equilibrium. Because channel width and meander geometry are closely related, we use a numerical meander model that allows for independent migration of both banks, thereby allowing channel width to vary in space and time. We hypothesize that confined meanders with persistent angular bends have smaller transport rates of bed material and that their migration is driven by erosion of the cutbank (bank-pull migration). When bed material supply is sufficiently large that point bar deposition drives meander migration (bar-push migration), confined meander bends have a larger radius of curvature and a geometry that varies as the meander migrates. We test this hypothesis using historical patterns of confined meander migration for rivers with different rates of sediment supply and bed material transport. Interpretation of the meander migration pattern is provided by the free-width meander migration model.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Borthakur, Sanchayeeta; Heckman, Timothy; Tumlinson, Jason

We present a study exploring the nature and properties of the circumgalactic medium (CGM) and its connection to the atomic gas content in the interstellar medium (ISM) of galaxies as traced by the H i 21 cm line. Our sample includes 45 low-z (0.026–0.049) galaxies from the GALEX Arecibo SDSS Survey (Galaxy Evolution Explorer/Arecibo/Sloan Digital Sky Survey). Their CGM was probed via absorption in the spectra of background quasi-stellar objects at impact parameters of 63–231 kpc. The spectra were obtained with the Cosmic Origins Spectrograph aboard the Hubble Space Telescope. We detected neutral hydrogen (Lyα absorption lines) in the CGMmore » of 92% of the galaxies. We find that the radial profile of the CGM as traced by the Lyα equivalent width can be fit as an exponential with a scale length of roughly the virial radius of the dark matter halo. We found no correlation between the orientation of the sightline relative to the galaxy’s major axis and the Lyα equivalent width. The velocity spread of the circumgalactic gas is consistent with that seen in the atomic gas in the ISM. We find a strong correlation (99.8% confidence) between the gas fraction (M(H i)/M{sub ⋆}) and the impact-parameter-corrected Lyα equivalent width. This is stronger than the analogous correlation between corrected Lyα equivalent width and specific star formation rate (SFR)/M{sub ⋆} (97.5% confidence). These results imply a physical connection between the H i disk and the CGM, which is on scales an order of magnitude larger. This is consistent with the picture in which the H i disk is nourished by accretion of gas from the CGM.« less

Narrow chaotic compound autoionizing states in atomic spectra

DOE Office of Scientific and Technical Information (OSTI.GOV)

Flambaum, V.V.; Gribakina, A.A.; Gribakin, G.F.

1996-09-01

Simultaneous excitation of several valence electrons in atoms gives rise to a dense spectrum of compound autoionizing states (AIS). These states are almost chaotic superpositions of large numbers of many-electron basis states built of single-electron orbitals. The mean level spacing {ital D} between such states is very small (e.g., {ital D}{lt}0.01 eV for the numerical example of {ital J}{sup {pi}}=4{sup {minus}} states of Ce just above the ionization threshold). The autoionization widths of these states estimated by perturbations, {gamma}=2{pi}{vert_bar}{ital W}{vert_bar}{sup 2}, where {ital W} is the Coulomb matrix element coupling the AIS to the continuum, are also small, but comparablemore » with {ital D} in magnitude: {gamma}{approximately}{ital D}. Hence the nonperturbative interaction of AIS with each other via the continuum is very essential. It suppresses greatly the widths of the autoionizing resonances ({Gamma}{approx_equal}{ital D}{sup 2}/3{gamma}{lt}{ital D}), and leads to the emergence of a {open_quote}{open_quote}collective{close_quote}{close_quote} doorway state which accumulates a large share of the total width. This state is in essence a modified single-particle continuum decoupled from the resonances due to its large width. Narrow compound AIS should be a common feature of atomic spectra at energies sufficient for excitation of several electrons above the ground-state configuration. The narrow resonances can be observed as peaks in the photoabsorption, or, in electron-ion scattering, as Fano-type profiles on the background provided by the wide doorway-state resonance. It is also shown that the statistics of electromagnetic and autoionization amplitudes involving compound states are close to Gaussian. {copyright} {ital 1996 The American Physical Society.}« less

Linear dimensions of normal upper airway structure by magnetic resonance imaging in Chinese Han infants and preschool children.

PubMed

Yi, Xiaoli; Yao, Linyin; Yuan, Xinyu; Wei, Yongxiang; Wang, Zhenchang

2017-09-01

To establish normative data of upper airway structure in Chinese Han infants and preschool children. Magnetic resonance imaging (MRI) scans of 521 Chinese Han infants and preschool children (225 girls, 296 boys) aged from 1 day to 72 months were selected from the children who underwent head MRI at the Capital Institute of Pediatrics Affiliated Children Hospital, Beijing, China. No subjects had sleep-disordered breathing or associated conditions that may have affected the upper airway anatomy. The upper airway dimensions and surrounding soft tissue sizes were measured along the mid-sagittal and axial images. On images from the mid-sagittal image, the normative values of the following were obtained for all age group: thickness of the adenoid and nasopharyngeal area, length and thickness of the soft palate, length and height of the tongue, length of upper airway, distance between the mental spine and clivus, and the adenoid oblique width, soft palate oblique width, and tongue oblique width along the mental spine-clivus line. Normative values of the mean tonsillar width and intertonsillar space on the axial images were also obtained. There were no differences in any measurements between boys and girls in either infants or preschool children. Older children had larger airway dimensions, as expected. Normative values for upper airway structure in Chinese Han infants and preschool children assessed by MRI were established. The upper airway dimension and surrounding soft tissues size, including soft palate, adenoid, tongue, and tonsils, were increased with age. There were no gender differences during the first six years of life. These data may prove useful when studying airway disease in Chinese Han children. Copyright © 2017 Elsevier B.V. All rights reserved.

Detector Sampling of Optical/IR Spectra: How Many Pixels per FWHM?

NASA Astrophysics Data System (ADS)

Robertson, J. Gordon

2017-08-01

Most optical and IR spectra are now acquired using detectors with finite-width pixels in a square array. Each pixel records the received intensity integrated over its own area, and pixels are separated by the array pitch. This paper examines the effects of such pixellation, using computed simulations to illustrate the effects which most concern the astronomer end-user. It is shown that coarse sampling increases the random noise errors in wavelength by typically 10-20 % at 2 pixels per Full Width at Half Maximum, but with wide variation depending on the functional form of the instrumental Line Spread Function (i.e. the instrumental response to a monochromatic input) and on the pixel phase. If line widths are determined, they are even more strongly affected at low sampling frequencies. However, the noise in fitted peak amplitudes is minimally affected by pixellation, with increases less than about 5%. Pixellation has a substantial but complex effect on the ability to see a relative minimum between two closely spaced peaks (or relative maximum between two absorption lines). The consistent scale of resolving power presented by Robertson to overcome the inadequacy of the Full Width at Half Maximum as a resolution measure is here extended to cover pixellated spectra. The systematic bias errors in wavelength introduced by pixellation, independent of signal/noise ratio, are examined. While they may be negligible for smooth well-sampled symmetric Line Spread Functions, they are very sensitive to asymmetry and high spatial frequency sub-structure. The Modulation Transfer Function for sampled data is shown to give a useful indication of the extent of improperly sampled signal in an Line Spread Function. The common maxim that 2 pixels per Full Width at Half Maximum is the Nyquist limit is incorrect and most Line Spread Functions will exhibit some aliasing at this sample frequency. While 2 pixels per Full Width at Half Maximum is nevertheless often an acceptable minimum for moderate signal/noise work, it is preferable to carry out simulations for any actual or proposed Line Spread Function to find the effects of various sampling frequencies. Where spectrograph end-users have a choice of sampling frequencies, through on-chip binning and/or spectrograph configurations, it is desirable that the instrument user manual should include an examination of the effects of the various choices.

Few-Body Techniques Using Coordinate Space for Bound and Continuum States

NASA Astrophysics Data System (ADS)

Garrido, E.

2018-05-01

These notes are a short summary of a set of lectures given within the frame of the "Critical Stability of Quantum Few-Body Systems" International School held in the Max Planck Institute for the Physics of Complex Systems (Dresden). The main goal of the lectures has been to provide the basic ingredients for the description of few-body systems in coordinate space. The hyperspherical harmonic and the adiabatic expansion methods are introduced in detail, and subsequently used to describe bound and continuum states. The expressions for the cross sections and reaction rates for three-body processes are derived. The case of resonant scattering and the complex scaling method as a tool to obtain the resonance energy and width is also introduced.

High average power diode pumped solid state laser

NASA Astrophysics Data System (ADS)

Gao, Yue; Wang, Yanjie; Chan, Amy; Dawson, Murray; Greene, Ben

2017-03-01

A new generation of high average power pulsed multi-joule solid state laser system has been developed at EOS Space Systems for various space related tracking applications. It is a completely diode pumped, fully automated multi-stage system consisting of a pulsed single longitudinal mode oscillator, three stages of pre-amplifiers, two stages of power amplifiers, completely sealed phase conjugate mirror or stimulated Brillouin scattering (SBS) cell and imaging relay optics with spatial filters in vacuum cells. It is capable of generating pulse energy up to 4.7 J, a beam quality M 2 ~ 3, pulse width between 10-20 ns, and a pulse repetition rate between 100-200 Hz. The system has been in service for more than two years with excellent performance and reliability.

SEE Sensitivity Analysis of 180 nm NAND CMOS Logic Cell for Space Applications

NASA Astrophysics Data System (ADS)

Sajid, Muhammad

2016-07-01

This paper focus on Single Event Effects caused by energetic particle strike on sensitive locations in CMOS NAND logic cell designed in 180nm technology node to be operated in space radiation environment. The generation of SE transients as well as upsets as function of LET of incident particle has been determined for logic devices onboard LEO and GEO satellites. The minimum magnitude pulse and pulse-width for threshold LET was determined to estimate the vulnerability /susceptibility of device for heavy ion strike. The impact of temperature, strike location and logic state of NAND circuit on total SEU/SET rate was estimated with physical mechanism simulations using Visual TCAD, Genius, runSEU program and Crad computer codes.

Vector magnetic fields in sunspots. I - Stokes profile analysis using the Marshall Space Flight Center magnetograph

NASA Technical Reports Server (NTRS)

Balasubramaniam, K. S.; West, E. A.

1991-01-01

The Marshall Space Flight Center (MSFC) vector magnetograph is a tunable filter magnetograph with a bandpass of 125 mA. Results are presented of the inversion of Stokes polarization profiles observed with the MSFC vector magnetograph centered on a sunspot to recover the vector magnetic field parameters and thermodynamic parameters of the spectral line forming region using the Fe I 5250.2 A spectral line using a nonlinear least-squares fitting technique. As a preliminary investigation, it is also shown that the recovered thermodynamic parameters could be better understood if the fitted parameters like Doppler width, opacity ratio, and damping constant were broken down into more basic quantities like temperature, microturbulent velocity, or density parameter.

KSC-2012-4540

NASA Image and Video Library

2012-08-17

CAPE CANAVERAL, Fla. – Two manatees swim near the Banana River shoreline a few miles from the Vehicle Assembly Building at NASA's Kennedy Space Center in Florida. Kennedy is located on Merritt Island, a barrier island, about 34 miles long and varying in width from five to 10 miles. Only 6,000 acres are actually used for operational activities. The Kennedy Space Center is also a National Wildlife Refuge. Consisting of 140,000 acres, the refuge provides a wide variety of habitats: coastal dunes, saltwater estuaries and marshes, freshwater impoundments, scrub, pine flatwoods and hardwood hammocks providing habitat for more than 1,500 species of plants and animals. For more information, visit: http://ipv6.nasa.gov/centers/kennedy/shuttleoperations/alligators/kscovrv.html Photo credit: NASA/Ben Smegelsky