Space Qualification Test of a-Silicon Solar Cell Modules

NASA Technical Reports Server (NTRS)

Kim, Q.; Lawton, R. A.; Manion, S. J.; Okuno, J. O.; Ruiz, R. P.; Vu, D. T.; Kayali, S. A.; Jeffrey, F. R.

1997-01-01

The basic requirement of solar cell modules for space applications are generally described in MIL-S-83576 for the specific needs of the USAF. However, the specifications of solar cells intended for use on space terrestrial applications are not well defined. Therefore this qualification test effort was concentrated on critical areas specific to the microseismometer probe which is intended to be included in the Mars microprobe programs.

Site-specific management of cotton root rot using airborne and satellite imagery and variable rate technology

USDA-ARS?s Scientific Manuscript database

Cotton root rot is a serious cotton disease that can now be effectively controlled with Topguard Terra Fungicide. However, its recurrence in the same areas year after year makes fungicide application only to infested areas more effective and economical than uniform application. Base on 17 years of r...

Designing area optimized application-specific network-on-chip architectures while providing hard QoS guarantees.

PubMed

Khawaja, Sajid Gul; Mushtaq, Mian Hamza; Khan, Shoab A; Akram, M Usman; Jamal, Habib Ullah

2015-01-01

With the increase of transistors' density, popularity of System on Chip (SoC) has increased exponentially. As a communication module for SoC, Network on Chip (NoC) framework has been adapted as its backbone. In this paper, we propose a methodology for designing area-optimized application specific NoC while providing hard Quality of Service (QoS) guarantees for real time flows. The novelty of the proposed system lies in derivation of a Mixed Integer Linear Programming model which is then used to generate a resource optimal Network on Chip (NoC) topology and architecture while considering traffic and QoS requirements. We also present the micro-architectural design features used for enabling traffic and latency guarantees and discuss how the solution adapts for dynamic variations in the application traffic. The paper highlights the effectiveness of proposed method by generating resource efficient NoC solutions for both industrial and benchmark applications. The area-optimized results are generated in few seconds by proposed technique, without resorting to heuristics, even for an application with 48 traffic flows.

Designing Area Optimized Application-Specific Network-On-Chip Architectures while Providing Hard QoS Guarantees

PubMed Central

Khawaja, Sajid Gul; Mushtaq, Mian Hamza; Khan, Shoab A.; Akram, M. Usman; Jamal, Habib ullah

2015-01-01

With the increase of transistors' density, popularity of System on Chip (SoC) has increased exponentially. As a communication module for SoC, Network on Chip (NoC) framework has been adapted as its backbone. In this paper, we propose a methodology for designing area-optimized application specific NoC while providing hard Quality of Service (QoS) guarantees for real time flows. The novelty of the proposed system lies in derivation of a Mixed Integer Linear Programming model which is then used to generate a resource optimal Network on Chip (NoC) topology and architecture while considering traffic and QoS requirements. We also present the micro-architectural design features used for enabling traffic and latency guarantees and discuss how the solution adapts for dynamic variations in the application traffic. The paper highlights the effectiveness of proposed method by generating resource efficient NoC solutions for both industrial and benchmark applications. The area-optimized results are generated in few seconds by proposed technique, without resorting to heuristics, even for an application with 48 traffic flows. PMID:25898016

43 CFR 3583.3 - Applications for hardrock mineral leases.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 43 Public Lands: Interior 2 2011-10-01 2011-10-01 false Applications for hardrock mineral leases... LAND MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) SPECIAL LEASING AREAS Shasta and... hardrock mineral leases. No specific form is required. An application shall include the applicant's name...

43 CFR 3583.3 - Applications for hardrock mineral leases.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 43 Public Lands: Interior 2 2013-10-01 2013-10-01 false Applications for hardrock mineral leases... LAND MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) SPECIAL LEASING AREAS Shasta and... hardrock mineral leases. No specific form is required. An application shall include the applicant's name...

43 CFR 3583.3 - Applications for hardrock mineral leases.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 43 Public Lands: Interior 2 2014-10-01 2014-10-01 false Applications for hardrock mineral leases... LAND MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) SPECIAL LEASING AREAS Shasta and... hardrock mineral leases. No specific form is required. An application shall include the applicant's name...

43 CFR 3583.3 - Applications for hardrock mineral leases.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 43 Public Lands: Interior 2 2012-10-01 2012-10-01 false Applications for hardrock mineral leases... LAND MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) SPECIAL LEASING AREAS Shasta and... hardrock mineral leases. No specific form is required. An application shall include the applicant's name...

Hanford Facility dangerous waste permit application, liquid effluent retention facility and 200 area effluent treatment facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Coenenberg, J.G.

1997-08-15

The Hanford Facility Dangerous Waste Permit Application is considered to 10 be a single application organized into a General Information Portion (document 11 number DOE/RL-91-28) and a Unit-Specific Portion. The scope of the 12 Unit-Specific Portion is limited to Part B permit application documentation 13 submitted for individual, `operating` treatment, storage, and/or disposal 14 units, such as the Liquid Effluent Retention Facility and 200 Area Effluent 15 Treatment Facility (this document, DOE/RL-97-03). 16 17 Both the General Information and Unit-Specific portions of the Hanford 18 Facility Dangerous Waste Permit Application address the content of the Part B 19 permit applicationmore » guidance prepared by the Washington State Department of 20 Ecology (Ecology 1987 and 1996) and the U.S. Environmental Protection Agency 21 (40 Code of Federal Regulations 270), with additional information needs 22 defined by the Hazardous and Solid Waste Amendments and revisions of 23 Washington Administrative Code 173-303. For ease of reference, the Washington 24 State Department of Ecology alpha-numeric section identifiers from the permit 25 application guidance documentation (Ecology 1996) follow, in brackets, the 26 chapter headings and subheadings. A checklist indicating where information is 27 contained in the Liquid Effluent Retention Facility and 200 Area Effluent 28 Treatment Facility permit application documentation, in relation to the 29 Washington State Department of Ecology guidance, is located in the Contents 30 Section. 31 32 Documentation contained in the General Information Portion is broader in 33 nature and could be used by multiple treatment, storage, and/or disposal units 34 (e.g., the glossary provided in the General Information Portion). Wherever 35 appropriate, the Liquid Effluent Retention Facility and 200 Area Effluent 36 Treatment Facility permit application documentation makes cross-reference to 37 the General Information Portion, rather than duplicating text. 38 39 Information provided in this Liquid Effluent Retention Facility and 40 200 Area Effluent Treatment Facility permit application documentation is 41 current as of June 1, 1997.« less

An information adaptive system study report and development plan

NASA Technical Reports Server (NTRS)

Ataras, W. S.; Eng, K.; Morone, J. J.; Beaudet, P. R.; Chin, R.

1980-01-01

The purpose of the information adaptive system (IAS) study was to determine how some selected Earth resource applications may be processed onboard a spacecraft and to provide a detailed preliminary IAS design for these applications. Detailed investigations of a number of applications were conducted with regard to IAS and three were selected for further analysis. Areas of future research and development include algorithmic specifications, system design specifications, and IAS recommended time lines.

Methodology, status and plans for development and assessment of TUF and CATHENA codes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Luxat, J.C.; Liu, W.S.; Leung, R.K.

1997-07-01

An overview is presented of the Canadian two-fluid computer codes TUF and CATHENA with specific focus on the constraints imposed during development of these codes and the areas of application for which they are intended. Additionally a process for systematic assessment of these codes is described which is part of a broader, industry based initiative for validation of computer codes used in all major disciplines of safety analysis. This is intended to provide both the licensee and the regulator in Canada with an objective basis for assessing the adequacy of codes for use in specific applications. Although focused specifically onmore » CANDU reactors, Canadian experience in developing advanced two-fluid codes to meet wide-ranging application needs while maintaining past investment in plant modelling provides a useful contribution to international efforts in this area.« less

Validation and evaluation of common large-area display set (CLADS) performance specification

NASA Astrophysics Data System (ADS)

Hermann, David J.; Gorenflo, Ronald L.

1998-09-01

Battelle is under contract with Warner Robins Air Logistics Center to design a Common Large Area Display Set (CLADS) for use in multiple Command, Control, Communications, Computers, and Intelligence (C4I) applications that currently use 19- inch Cathode Ray Tubes (CRTs). Battelle engineers have built and fully tested pre-production prototypes of the CLADS design for AWACS, and are completing pre-production prototype displays for three other platforms simultaneously. With the CLADS design, any display technology that can be packaged to meet the form, fit, and function requirements defined by the Common Large Area Display Head Assembly (CLADHA) performance specification is a candidate for CLADS applications. This technology independent feature reduced the risk of CLADS development, permits life long technology insertion upgrades without unnecessary redesign, and addresses many of the obsolescence problems associated with COTS technology-based acquisition. Performance and environmental testing were performed on the AWACS CLADS and continues on other platforms as a part of the performance specification validation process. A simulator assessment and flight assessment were successfully completed for the AWACS CLADS, and lessons learned from these assessments are being incorporated into the performance specifications. Draft CLADS specifications were released to potential display integrators and manufacturers for review in 1997, and the final version of the performance specifications are scheduled to be released to display integrators and manufacturers in May, 1998. Initial USAF applications include replacements for the E-3 AWACS color monitor assembly, E-8 Joint STARS graphics display unit, and ABCCC airborne color display. Initial U.S. Navy applications include the E-2C ACIS display. For these applications, reliability and maintainability are key objectives. The common design will reduce the cost of operation and maintenance by an estimated 3.3M per year on E-3 AWACS alone. It is realistic to anticipate savings of over 30M per year as CLADS is implemented widely across DoD applications. As commonality and open systems interfaces begin to surface in DoD applications, the CLADS architecture can easily and cost effectively absorb the changes, and avoid COTS obsolescence issues.

Site-specific management of cotton root rot using airborne and high resolution satellite imagery and variable rate technology

USDA-ARS?s Scientific Manuscript database

Cotton root rot is a century-old cotton disease that can now be effectively controlled with Topguard Terra Fungicide. As this disease tends to occur in the same general areas within fields in recurring years, site-specific application of the fungicide only to the infested areas can be more effective...

Software engineering with application-specific languages

NASA Technical Reports Server (NTRS)

Campbell, David J.; Barker, Linda; Mitchell, Deborah; Pollack, Robert H.

1993-01-01

Application-Specific Languages (ASL's) are small, special-purpose languages that are targeted to solve a specific class of problems. Using ASL's on software development projects can provide considerable cost savings, reduce risk, and enhance quality and reliability. ASL's provide a platform for reuse within a project or across many projects and enable less-experienced programmers to tap into the expertise of application-area experts. ASL's have been used on several software development projects for the Space Shuttle Program. On these projects, the use of ASL's resulted in considerable cost savings over conventional development techniques. Two of these projects are described.

Applications of Tethers in Space

NASA Technical Reports Server (NTRS)

Cron, A. C.

1985-01-01

The proceedings of the first workshop on applications of tethers in space are summarized. The workshop gathered personalities from industry, academic institutions and government to discuss the relatively new area of applied technology of very long tethers in space to a broad spectrum of future space missions. A large number of tethered concepts and configurations was presented covering electrodynamic interaction tethers, tethered transportation through angular momentum exchange, tethered constellations, low gravity utilization, applicable technology, and tethered test facilities. Specific recommendations were made to NASA in each area.

Nanoporous Ni with High Surface Area for Potential Hydrogen Storage Application.

PubMed

Zhou, Xiaocao; Zhao, Haibo; Fu, Zhibing; Qu, Jing; Zhong, Minglong; Yang, Xi; Yi, Yong; Wang, Chaoyang

2018-06-01

Nanoporous metals with considerable specific surface areas and hierarchical pore structures exhibit promising applications in the field of hydrogen storage, electrocatalysis, and fuel cells. In this manuscript, a facile method is demonstrated for fabricating nanoporous Ni with a high surface area by using SiO₂ aerogel as a template, i.e., electroless plating of Ni into an SiO₂ aerogel template followed by removal of the template at moderate conditions. The effects of the prepared conditions, including the electroless plating time, temperature of the structure, and the magnetism of nanoporous Ni are investigated in detail. The resultant optimum nanoporous Ni with a special 3D flower-like structure exhibited a high specific surface area of about 120.5 m²/g. The special nanoporous Ni exhibited a promising prospect in the field of hydrogen storage, with a hydrogen capacity of 0.45 wt % on 4.5 MPa at room temperature.

14 CFR 136.1 - Applicability and definitions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... (powered or un-powered), parachutes (powered or un-powered), gyroplanes, or airships. (d) For the purposes... site-specific areas would provide an emergency landing area for a single-engine helicopter or a multiengine helicopter that does not have the capability to reach a safe landing area after an engine power...

14 CFR 136.1 - Applicability and definitions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... (powered or un-powered), parachutes (powered or un-powered), gyroplanes, or airships. (d) For the purposes... site-specific areas would provide an emergency landing area for a single-engine helicopter or a multiengine helicopter that does not have the capability to reach a safe landing area after an engine power...

14 CFR 136.1 - Applicability and definitions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... (powered or un-powered), parachutes (powered or un-powered), gyroplanes, or airships. (d) For the purposes... site-specific areas would provide an emergency landing area for a single-engine helicopter or a multiengine helicopter that does not have the capability to reach a safe landing area after an engine power...

14 CFR 136.1 - Applicability and definitions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... (powered or un-powered), parachutes (powered or un-powered), gyroplanes, or airships. (d) For the purposes... site-specific areas would provide an emergency landing area for a single-engine helicopter or a multiengine helicopter that does not have the capability to reach a safe landing area after an engine power...

14 CFR 136.1 - Applicability and definitions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... (powered or un-powered), parachutes (powered or un-powered), gyroplanes, or airships. (d) For the purposes... site-specific areas would provide an emergency landing area for a single-engine helicopter or a multiengine helicopter that does not have the capability to reach a safe landing area after an engine power...

Applications of aerospace technology to petroleum extraction and reservoir engineering

NASA Technical Reports Server (NTRS)

Jaffe, L. D.; Back, L. H.; Berdahl, C. M.; Collins, E. E., Jr.; Gordon, P. G.; Houseman, J.; Humphrey, M. F.; Hsu, G. C.; Ham, J. D.; Marte, J. E.;

Interrogating discourse: the application of Foucault's methodological discussion to specific inquiry.

PubMed

Fadyl, Joanna K; Nicholls, David A; McPherson, Kathryn M

2013-09-01

Discourse analysis following the work of Michel Foucault has become a valuable methodology in the critical analysis of a broad range of topics relating to health. However, it can be a daunting task, in that there seems to be both a huge number of possible approaches to carrying out this type of project, and an abundance of different, often conflicting, opinions about what counts as 'Foucauldian'. This article takes the position that methodological design should be informed by ongoing discussion and applied as appropriate to a particular area of inquiry. The discussion given offers an interpretation and application of Foucault's methodological principles, integrating a reading of Foucault with applications of his work by other authors, showing how this is then applied to interrogate the practice of vocational rehabilitation. It is intended as a contribution to methodological discussion in this area, offering an interpretation of various methodological elements described by Foucault, alongside specific application of these aspects.

Activated carbon electrode from banana-peel waste for supercapacitor applications

NASA Astrophysics Data System (ADS)

Taer, E.; Taslim, R.; Aini, Z.; Hartati, S. D.; Mustika, W. S.

2017-01-01

Seven types of activated carbon electrode (ACM) have been produced from the banana peel waste for supercapacitor application. The difference type of the electrode was synthesized by the various conditions of carbonization and activation. The production of the ACM was begun by the milling process and molded by a solution casting technique. The next step was followed by drying, carbonization and activation process. Physical properties of the ACM were studied by the N2 gas absorption-desorption method to characterize the specific surface area of the sample. On the other side, the electrochemical properties such as specific capacitance (Csp), specific energy (E) and specific power (P) were resulted by calculating the current (I) and voltage (V) data from the cyclic voltammetry testing. Based on the data obtained the surface area of the ACM has a significant relationship with the electrochemical properties. The specific surface area (SBET), Csp, E and P were found the maximum value as high as 581m2 / g, 68 F/g, 0.75 Wh/kg and 31 W/kg, respectively. Further more, this paper were also analyzed the relationship between electrochemical properties of supercapacitor with the degree of crystallization of the ACM.

Learning Objects for Educational Applications via PDA Technology

ERIC Educational Resources Information Center

Churchill, Daniel

2008-01-01

This article discusses an ongoing study into issues relevant to the design of learning objects for educational applications via portable digital assistant (PDA) technology. The specific areas of inquiry in this study are: the kinds of learning objects that are effective for PDA delivery; contexts for their effective educational applications; and…

Properties that influence the specific surface areas of carbon nanotubes and nanofibers.

PubMed

Birch, M Eileen; Ruda-Eberenz, Toni A; Chai, Ming; Andrews, Ronnee; Hatfield, Randal L

2013-11-01

Commercially available carbon nanotubes and nanofibers were analyzed to examine possible relationships between their Brunauer-Emmett-Teller specific surface areas (SSAs) and their physical and chemical properties. Properties found to influence surface area were number of walls/diameter, impurities, and surface functionalization with hydroxyl and carboxyl groups. Characterization by electron microscopy, energy-dispersive X-ray spectrometry, thermogravimetric analysis, and elemental analysis indicates that SSA can provide insight on carbon nanomaterials properties, which can differ vastly depending on synthesis parameters and post-production treatments. In this study, how different properties may influence surface area is discussed. The materials examined have a wide range of surface areas. The measured surface areas differed from product specifications, to varying degrees, and between similar products. Findings emphasize the multiple factors that influence surface area and mark its utility in carbon nanomaterial characterization, a prerequisite to understanding their potential applications and toxicities. Implications for occupational monitoring are discussed.

UV imaging reveals facial areas that are prone to skin cancer are disproportionately missed during sunscreen application.

PubMed

Pratt, Harry; Hassanin, Kareem; Troughton, Lee D; Czanner, Gabriela; Zheng, Yalin; McCormick, Austin G; Hamill, Kevin J

2017-01-01

Application of sunscreen is a widely used mechanism for protecting skin from the harmful effects of UV light. However, protection can only be achieved through effective application, and areas that are routinely missed are likely at increased risk of UV damage. Here we sought to determine if specific areas of the face are missed during routine sunscreen application, and whether provision of public health information is sufficient to improve coverage. To investigate this, 57 participants were imaged with a UV sensitive camera before and after sunscreen application: first visit; minimal pre-instruction, second visit; provided with a public health information statement. Images were scored using a custom automated image analysis process designed to identify areas of high UV reflectance, i.e. missed during sunscreen application, and analysed for 5% significance. Analyses revealed eyelid and periorbital regions to be disproportionately missed during routine sunscreen application (median 14% missed in eyelid region vs 7% in rest of face, p<0.01). Provision of health information caused a significant improvement in coverage to eyelid areas in general however, the medial canthal area was still frequently missed. These data reveal that a public health announcement-type intervention could be effective at improving coverage of high risk areas of the face, however high risk areas are likely to remain unprotected therefore other mechanisms of sun protection should be widely promoted such as UV blocking sunglasses.

Recent advances in the fabrication and structure-specific applications of graphene-based inorganic hybrid membranes.

PubMed

Zhao, Xinne; Zhang, Panpan; Chen, Yuting; Su, Zhiqiang; Wei, Gang

2015-03-12

The preparation and applications of graphene (G)-based materials are attracting increasing interests due to their unique electronic, optical, magnetic, thermal, and mechanical properties. Compared to G-based hybrid and composite materials, G-based inorganic hybrid membrane (GIHM) offers enormous advantages ascribed to their facile synthesis, planar two-dimensional multilayer structure, high specific surface area, and mechanical stability, as well as their unique optical and mechanical properties. In this review, we report the recent advances in the technical fabrication and structure-specific applications of GIHMs with desirable thickness and compositions. In addition, the advantages and disadvantages of the methods utilized for creating GIHMs are discussed in detail. Finally, the potential applications and key challenges of GIHMs for future technical applications are mentioned.

A site-specific slurry application technique on grassland and on arable crops.

PubMed

Schellberg, Jürgen; Lock, Reiner

2009-01-01

There is evidence that unequal slurry application on agricultural land contributes to N losses to the environment. Heterogeneity within fields demands adequate response by means of variable rate application. A technique is presented which allows site-specific application of slurry on grassland and arable land based on pre-defined application maps. The system contains a valve controlling flow rate by an on-board PC. During operation, flow rate is measured and scaled against set point values given in the application map together with the geographic position of the site. The systems worked sufficiently precise at a flow rate between 0 and 25 l s(-1) and an offset of actual slurry flow from set point values between 0.33 and 0.67 l s(-1). Long-term experimentation is required to test if site-specific application de facto reduces N surplus within fields and so significantly contributes to the unloading of N in agricultural areas.

Conceptual design study of concentrator enhanced solar arrays for space applications. 2kW Si and GaAs systems at 1 AU

NASA Technical Reports Server (NTRS)

1980-01-01

The effect of concentration level on the specific power for a deployable, thin, gallium arsenide cell array in geosynchronous orbit for 10 years in conjunction with a two dimensional flat plate trough concentrator (V trough) and also with a multiple flat plate concentrator was investigated as well as the effects for a conventional silicon cell array on a rigid substrate. For application to a thin GaAs array at 1 AU for 10 years, the V trough produces a 19% benefit in specific power and a dramatic reduction in array area, while the multiple flat plate collector design is not only of no benefit, but is a considerable detriment. The benefit it achieves by reducing array area is duplicated by the 2D design. For the silicon array on a rigid substrate, improvement in performance due to a concentrator with ordinary mirror coating is quite small: 9% increase in specific power, and 13% reduction in array area. When the concentrator mirrors are coated with an improved cold mirror coating, somewhat more significant results are obtained: 31% specific power improvement; and 27% area reduction. In both cases, a 10 year exposure reduces BOL output by 23%.

National Emissions Standards for Hazardous Air Pollutants (NESHAP) for Area Source Standards for Prepared Feeds Manufacturing: Commonly Asked Questions and Answers

EPA Pesticide Factsheets

This 2011 document answers common questions about the NESHAP for Area Sources for Prepared Feeds Manufacturing. The questions range in topics including applicability, specific requirements, and recordkeeping.

36 CFR 4.2 - State law applicable.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 36 Parks, Forests, and Public Property 1 2011-07-01 2011-07-01 false State law applicable. 4.2... AND TRAFFIC SAFETY § 4.2 State law applicable. (a) Unless specifically addressed by regulations in this chapter, traffic and the use of vehicles within a park area are governed by State law. State law...

76 FR 40688 - Foreign-Trade Zone 71-Windsor Locks, CT Application for Expansion

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-11

... Locks, CT Application for Expansion An application has been submitted to the Foreign-Trade Zones Board... 2 (390 acres)--within the 600-acre New England Tradeport business park located at the intersection... distribution services to area businesses. No specific manufacturing authority is being requested at this time...

Current status and future directions of precision aerial application for site-specific crop management in the USA

USDA-ARS?s Scientific Manuscript database

The first variable-rate aerial application system was developed about a decade ago in the USA and since then, aerial application has benefitted from these technologies. Many areas of the United States rely on readily available agricultural airplanes or helicopters for pest management, and variable-...

NRL Fact Book

DTIC Science & Technology

1976-07-01

Systems Division ......... ........................ 60 Oceanology Area ........... ............................ 62 Shipboard Computing Group...directed toward new and improved materials, equipment, techniques, systems , and related operational procedures for the Navy. In fulfillment of this...Within areas of technological expertise, develops prototype systems applicable to specific projects. (d) Performs scientific research development for

Application of probabilistic analysis/design methods in space programs - The approaches, the status, and the needs

NASA Technical Reports Server (NTRS)

Ryan, Robert S.; Townsend, John S.

1993-01-01

The prospective improvement of probabilistic methods for space program analysis/design entails the further development of theories, codes, and tools which match specific areas of application, the drawing of lessons from previous uses of probability and statistics data bases, the enlargement of data bases (especially in the field of structural failures), and the education of engineers and managers on the advantages of these methods. An evaluation is presently made of the current limitations of probabilistic engineering methods. Recommendations are made for specific applications.

Applications of aerospace technology to petroleum exploration. Volume 2: Appendices

NASA Technical Reports Server (NTRS)

Jaffe, L. D.

1976-01-01

Participants in the investigation of problem areas in oil exploration are listed and the data acquisition methods used to determine categories to be studied are described. Specific aerospace techniques applicable to the tasks identified are explained and their costs evaluated.

Porous silicon structures with high surface area/specific pore size

DOEpatents

Northrup, M.A.; Yu, C.M.; Raley, N.F.

1999-03-16

Fabrication and use of porous silicon structures to increase surface area of heated reaction chambers, electrophoresis devices, and thermopneumatic sensor-actuators, chemical preconcentrates, and filtering or control flow devices. In particular, such high surface area or specific pore size porous silicon structures will be useful in significantly augmenting the adsorption, vaporization, desorption, condensation and flow of liquids and gases in applications that use such processes on a miniature scale. Examples that will benefit from a high surface area, porous silicon structure include sample preconcentrators that are designed to adsorb and subsequently desorb specific chemical species from a sample background; chemical reaction chambers with enhanced surface reaction rates; and sensor-actuator chamber devices with increased pressure for thermopneumatic actuation of integrated membranes. Examples that benefit from specific pore sized porous silicon are chemical/biological filters and thermally-activated flow devices with active or adjacent surfaces such as electrodes or heaters. 9 figs.

Porous silicon structures with high surface area/specific pore size

DOEpatents

Northrup, M. Allen; Yu, Conrad M.; Raley, Norman F.

1999-01-01

Fabrication and use of porous silicon structures to increase surface area of heated reaction chambers, electrophoresis devices, and thermopneumatic sensor-actuators, chemical preconcentrates, and filtering or control flow devices. In particular, such high surface area or specific pore size porous silicon structures will be useful in significantly augmenting the adsorption, vaporization, desorption, condensation and flow of liquids and gasses in applications that use such processes on a miniature scale. Examples that will benefit from a high surface area, porous silicon structure include sample preconcentrators that are designed to adsorb and subsequently desorb specific chemical species from a sample background; chemical reaction chambers with enhanced surface reaction rates; and sensor-actuator chamber devices with increased pressure for thermopneumatic actuation of integrated membranes. Examples that benefit from specific pore sized porous silicon are chemical/biological filters and thermally-activated flow devices with active or adjacent surfaces such as electrodes or heaters.

UV imaging reveals facial areas that are prone to skin cancer are disproportionately missed during sunscreen application

PubMed Central

Troughton, Lee D.; Czanner, Gabriela; Zheng, Yalin; McCormick, Austin G.

2017-01-01

Application of sunscreen is a widely used mechanism for protecting skin from the harmful effects of UV light. However, protection can only be achieved through effective application, and areas that are routinely missed are likely at increased risk of UV damage. Here we sought to determine if specific areas of the face are missed during routine sunscreen application, and whether provision of public health information is sufficient to improve coverage. To investigate this, 57 participants were imaged with a UV sensitive camera before and after sunscreen application: first visit; minimal pre-instruction, second visit; provided with a public health information statement. Images were scored using a custom automated image analysis process designed to identify areas of high UV reflectance, i.e. missed during sunscreen application, and analysed for 5% significance. Analyses revealed eyelid and periorbital regions to be disproportionately missed during routine sunscreen application (median 14% missed in eyelid region vs 7% in rest of face, p<0.01). Provision of health information caused a significant improvement in coverage to eyelid areas in general however, the medial canthal area was still frequently missed. These data reveal that a public health announcement-type intervention could be effective at improving coverage of high risk areas of the face, however high risk areas are likely to remain unprotected therefore other mechanisms of sun protection should be widely promoted such as UV blocking sunglasses. PMID:28968413

Conductivity enhancement of carbon aerogel by modified gelation using self additive

NASA Astrophysics Data System (ADS)

Singh, Ashish; Kohli, D. K.; Bhartiya, Sushmita; Singh, Rashmi; Rajak, Gaurav; Singh, M. K.; Karnal, A. K.

2018-04-01

Carbon aerogels having high surface area and open pore structure are being studied for many electrochemical applications such as fuel cells and super capacitors. Moderate electrical conductivity of resorcinol - formaldehyde (R-F) derived carbon aerogel limits its utility in these applications. The current manuscript briefs about the synthesis of composite carbon aerogel using carbon aerogel itself as additive during gelation of water based carbon aerogel and study the effect on its conductivity and surface properties. The additive carbon aerogel was synthesized and pre-treated at higher temperature to achieve enhancement in conductivity. The composite carbon aerogel (CCA) samples were characterized for surface area properties, morphology, electrical conductivity and specific capacitance. The surface area properties of CCA showed improvement and specific surface area of ˜1798 m2/g with total pore volume of 1.7 cm3/g. was obtained. The electrical conductivity of the composite carbon aerogel with 5 wt % additive showed improvement over the plain carbon aerogel with respective values of 144 S/m and 128 S/m. The specific capacitance evaluated for CA and CCA are 102 and 118 F/g at scan rate of 10mV/s with improvement of ˜16%.

Area-specific recreation use estimation using the national visitor use monitoring program data.

Treesearch

Eric M. White; Stanley J. Zarnoch; Donald B.K. English

2007-01-01

Estimates of national forest recreation use are available at the national, regional, and forest levels via the USDA Forest Service National Visitor Use Monitoring (NVUM) program. In some resource planning and management applications, analysts desire recreation use estimates for subforest areas within an individual national forest or for subforest areas that combine...

Advanced local area network concepts

NASA Technical Reports Server (NTRS)

Grant, Terry

1985-01-01

Development of a good model of the data traffic requirements for Local Area Networks (LANs) onboard the Space Station is the driving problem in this work. A parameterized workload model is under development. An analysis contract has been started specifically to capture the distributed processing requirements for the Space Station and then to develop a top level model to simulate how various processing scenarios can handle the workload and what data communication patterns result. A summary of the Local Area Network Extendsible Simulator 2 Requirements Specification and excerpts from a grant report on the topological design of fiber optic local area networks with application to Expressnet are given.

Vertical leaf area distribution, light transmittance, and application of the Beer-Lambert Law in four mature hardwood stands in the southern Appalachians

Treesearch

James M. Vose; Neal H. Sullivan; Barton D. Clinton; Paul V. Bolstad

1995-01-01

We quantified stand leaf area index and vertical leaf area distribution, and developed canopy extinction coefficients (k), in four mature hardwood stands. Leaf area index, calculated from litter fall and specific leaf area (cm²·g-1), ranged from 4.3 to 5.4 m²·m-2. In three of the four stands, leaf area was distributed in...

Sensor Fusion and Smart Sensor in Sports and Biomedical Applications.

PubMed

Mendes, José Jair Alves; Vieira, Mário Elias Marinho; Pires, Marcelo Bissi; Stevan, Sergio Luiz

2016-09-23

The following work presents an overview of smart sensors and sensor fusion targeted at biomedical applications and sports areas. In this work, the integration of these areas is demonstrated, promoting a reflection about techniques and applications to collect, quantify and qualify some physical variables associated with the human body. These techniques are presented in various biomedical and sports applications, which cover areas related to diagnostics, rehabilitation, physical monitoring, and the development of performance in athletes, among others. Although some applications are described in only one of two fields of study (biomedicine and sports), it is very likely that the same application fits in both, with small peculiarities or adaptations. To illustrate the contemporaneity of applications, an analysis of specialized papers published in the last six years has been made. In this context, the main characteristic of this review is to present the largest quantity of relevant examples of sensor fusion and smart sensors focusing on their utilization and proposals, without deeply addressing one specific system or technique, to the detriment of the others.

Cryogenic fluid management in space

NASA Technical Reports Server (NTRS)

Antar, Basil N.

1988-01-01

Many future space based vehicles and satellites will require on orbit refuelling procedures. Cryogenic fluid management technology is being developed to assess the requirements of such procedures as well as to aid in the design and development of these vehicles. Cryogenic fluid management technology for this application could be divided into two areas of study, one is concerned with fluid transfer process and the other with cryogenic liquid storage. This division is based upon the needed technology for the development of each area. In the first, the interaction of fluid dynamics with thermodynamics is essential, while in the second only thermodynamic analyses are sufficient to define the problem. The following specific process related to the liquid transfer area are discussed: tank chilldown and fill; tank pressurization; liquid positioning; and slosh dynamics and control. These specific issues are discussed in relation with the required technology for their development in the low gravity application area. In each process the relevant physics controlling the technology is identified and methods for resolving some of the basic questions are discussed.

Iowa Commercial Pesticide Applicator Manual, Category 5: Aquatic Pest Control. CS-17.

ERIC Educational Resources Information Center

Jennings, Vivan M.; Ryan, Stephen O.

This manual provides information needed to meet specific standards for certification as a pesticide applicator. The text is concerned with the control of aquatic weeds in a variety of water use situations, i.e. static water, limited-flow impoundments and moving water. Also discussed are the principles of limited area application such as surface or…

Aerial spray technology: possibilities and limitations for control of pear thrips

Treesearch

Karl Mierzejewski

1991-01-01

The feasibility of using aerial application as a means of managing a pear thrips infestation in maple forest stands is examined, based on existing knowledge of forest aerial application acquired from theoretical and empirical studies. Specific strategies by which aerial application should be performed and potential problem areas are discussed. Two new tools, aircraft...

[Nutrient use efficiency and yield-increasing effect of single basal application of rice specific controlled release fertilizer].

PubMed

Chen, Jiansheng; Xu, Peizhi; Tang, Shuanhu; Zhang, Fabao; Xie, Chunsheng

2005-10-01

A series of pot and field experiments and field demonstrations showed that in comparing with the commonly used specific-fertilizers containing same amounts of nutrients, single basal application of rice-specific controlled release fertilizer could increase the use efficiency of N and P by 12.2% - 22.7% and 7.0% - 35.0%, respectively in pot experiment, and the use efficiency of N by 17.1% in field experiment. In 167 field demonstrations successively conducted for 3 years in various rice production areas of Guangdong Province, single basal application of the fertilizer saved the application rate of N and P by 22.1% and 21.8%, respectively, and increased the yield by 8.2%, compared with normal split fertilization.

The worldwide market for photovoltaics in the rural sector

NASA Technical Reports Server (NTRS)

Brainard, W. A.

1982-01-01

The worldwide market for stand-alone photovoltaic power systems in three specific segments of the rural sector were determined. The worldwide market for photovoltaic power systems for village power, cottage industry, and agricultural applications were addressed. The objectives of these studies were to: The market potential for small stand-alone photovoltaic power system in specific application areas was assessed. Technical, social and institutional barriers to PV utilization were identified. Funding sources available to potential users was also identified and marketing strategies appropriate for each sector were recommended to PV product manufacturers. The studies were prepared on the basis of data gathered from domestic sources and from field trips to representative countries. Both country-specific and sector-specific results are discussed, and broadly applicable barriers pertinent to international marketing of PV products are presented.

User's guide and tape specification for ERB 7 DELMAT

NASA Technical Reports Server (NTRS)

Ardanuy, P.; Penn, L.

1985-01-01

Guidance is provided to the DELMAT user in the areas of purpose, use and limitations of DELMAT tapes and software. The DELMAT tape specifications is also provided. The ERB-7, ERB MAT and tape characteristics applicable to the DELMAT tapes are also summarized.

Applications of artificial intelligence to rotorcraft

NASA Technical Reports Server (NTRS)

Abbott, Kathy H.

1987-01-01

The application of AI technology may have significant potential payoff for rotorcraft. In the near term, the status of the technology will limit its applicability to decision aids rather than total automation. The specific application areas are categorized into onboard and nonflight aids. The onboard applications include: fault monitoring, diagnosis, and reconfiguration; mission and tactics planning; situation assessment; navigation aids, especially in nap-of-the-earth flight; and adaptive man-machine interfaces. The nonflight applications include training and maintenance diagnostics.

Crystalline mesoporous tungsten oxide nanoplate monoliths synthesized by directed soft template method for highly sensitive NO{sub 2} gas sensor applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hoa, Nguyen Duc, E-mail: ndhoa@itims.edu.vn; Duy, Nguyen Van; Hieu, Nguyen Van, E-mail: hieu@itims.edu.vn

2013-02-15

Graphical abstract: Display Omitted Highlights: ► Mesoporous WO{sub 3} nanoplate monoliths were obtained by direct templating synthesis. ► Enable effective accession of the analytic molecules for the sensor applications. ► The WO{sub 3} sensor exhibited a high performance to NO{sub 2} gas at low temperature. -- Abstract: Controllable synthesis of nanostructured metal oxide semiconductors with nanocrystalline size, porous structure, and large specific surface area is one of the key issues for effective gas sensor applications. In this study, crystalline mesoporous tungsten oxide nanoplate-like monoliths with high specific surface areas were obtained through instant direct-templating synthesis for highly sensitive nitrogen dioxidemore » (NO{sub 2}) sensor applications. The copolymer soft template was converted into a solid carbon framework by heat treatment in an inert gas prior to calcinations in air to sustain the mesoporous structure of tungsten oxide. The multidirectional mesoporous structures of tungsten oxide with small crystalline size, large specific surface area, and superior physical characteristics enabled the rapid and effective accession of analytic gas molecules. As a result, the sensor response was enhanced and the response and recovery times were reduced, in which the mesoporous tungsten oxide based gas sensor exhibited a superior response of 21,155% to 5 ppm NO{sub 2}. In addition, the developed sensor exhibited selective detection of low NO{sub 2} concentration in ammonia and ethanol at a low temperature of approximately 150 °C.« less

National Knowledge Commission

NASA Astrophysics Data System (ADS)

Pitroda, Sam

2007-04-01

India's National Knowledge Commission (NKC) established by the prime minister is focused on building institutions and infrastructure in Education, Science and Technology, Innovation etc. to meet the challenges of the knowledge economy in the 21st century and increase India's competitive advantage in the global market. India today stands poised to reap the benefits of a rapidly growing economy and a major demographic advantage, with 550 million young people below the age of 25 years, the largest in the world. The NKC is focused on five critical areas of knowledge related to access, concepts, creation, applications and services. This includes a variety of subject areas such as language, translations, libraries, networks, portals, affirmative action, distance learning, intellectual property, Entrepreneurship, application in Agriculture, health, small and medium scale industries, e-governance etc. One of the keys to this effort is to build a national broadband gigabit of networks of 500 nodes to connect universities, Libraries, Laboratories, Hospitals, Agriculture institutions etc. to share resources and collaborate on multidisciplinary activities. This presentation will introduce the NKC, discuss methodology, subject areas, specific recommendation and outline a plan to build knowledge networks and specifics on network architecture, applications, and utilities.

Printable Electrochemical Biosensors: A Focus on Screen-Printed Electrodes and Their Application

PubMed Central

Yamanaka, Keiichiro; Vestergaard, Mun’delanji C.; Tamiya, Eiichi

2016-01-01

In this review we present electrochemical biosensor developments, focusing on screen-printed electrodes (SPEs) and their applications. In particular, we discuss how SPEs enable simple integration, and the portability needed for on-field applications. First, we briefly discuss the general concept of biosensors and quickly move on to electrochemical biosensors. Drawing from research undertaken in this area, we cover the development of electrochemical DNA biosensors in great detail. Through specific examples, we describe the fabrication and surface modification of printed electrodes for sensitive and selective detection of targeted DNA sequences, as well as integration with reverse transcription-polymerase chain reaction (RT-PCR). For a more rounded approach, we also touch on electrochemical immunosensors and enzyme-based biosensors. Last, we present some electrochemical devices specifically developed for use with SPEs, including USB-powered compact mini potentiostat. The coupling demonstrates the practical use of printable electrode technologies for application at point-of-use. Although tremendous advances have indeed been made in this area, a few challenges remain. One of the main challenges is application of these technologies for on-field analysis, which involves complicated sample matrices. PMID:27775661

Mispronunciation Detection for Language Learning and Speech Recognition Adaptation

ERIC Educational Resources Information Center

Ge, Zhenhao

2013-01-01

The areas of "mispronunciation detection" (or "accent detection" more specifically) within the speech recognition community are receiving increased attention now. Two application areas, namely language learning and speech recognition adaptation, are largely driving this research interest and are the focal points of this work.…

Increase of porosity by combining semi-carbonization and KOH activation of formaldehyde resins to prepare high surface area carbons for supercapacitor applications

NASA Astrophysics Data System (ADS)

Heimböckel, Ruben; Kraas, Sebastian; Hoffmann, Frank; Fröba, Michael

2018-01-01

A series of porous carbon samples were prepared by combining a semi-carbonization process of acidic polymerized phenol-formaldehyde resins and a following chemical activation with KOH used in different ratios to increase specific surface area, micropore content and pore sizes of the carbons which is favourable for supercapacitor applications. Samples were characterized by nitrogen physisorption, powder X-ray diffraction, Raman spectroscopy and scanning electron microscopy. The results show that the amount of KOH, combined with the semi-carbonization step had a remarkable effect on the specific surface area (up to SBET: 3595 m2 g-1 and SDFT: 2551 m2 g-1), pore volume (0.60-2.62 cm3 g-1) and pore sizes (up to 3.5 nm). The carbons were tested as electrode materials for electrochemical double layer capacitors (EDLC) in a two electrode setup with tetraethylammonium tetrafluoroborate in acetonitrile as electrolyte. The prepared carbon material with the largest surface area, pore volume and pore sizes exhibits a high specific capacitance of 145.1 F g-1 at a current density of 1 A g-1. With a high specific energy of 31 W h kg-1 at a power density of 33028 W kg-1 and a short time relaxation constant of 0.29 s, the carbon showed high power capability as an EDLC electrode material.

Rural Active Living: A Call to Action.

PubMed

Umstattd Meyer, M Renée; Moore, Justin B; Abildso, Christiaan; Edwards, Michael B; Gamble, Abigail; Baskin, Monica L

2016-01-01

Rural residents are less physically active than their urban counterparts and disproportionately affected by chronic diseases and conditions associated with insufficient activity. While the ecological model has been successful in promoting and translating active living research in urban settings, relatively little research has been conducted in rural settings. The resulting research gap prohibits a comprehensive understanding and application of solutions for active living in rural America. Therefore, the purpose of this article was to assess the evidence base for an ecological model of active living for rural populations and outline key scientific gaps that inhibit the development and application of solutions. Specifically, we reexamined the 4 domains conceptualized by the model and suggest that there is a dearth of research specific to rural communities across all areas of the framework. Considering the limited rural-specific efforts, we propose areas that need addressing to mobilize rural active living researchers and practitioners into action.

Rural Active Living: A Call to Action

PubMed Central

Meyer, M. Renée Umstattd; Moore, Justin B.; Abildso, Christiaan; Edwards, Michael B.; Gamble, Abigail; Baskin, Monica L.

2015-01-01

Rural residents are less physically active than their urban counterparts and disproportionately affected by chronic diseases and conditions associated with insufficient activity. While the ecological model has been successful in promoting and translating active living research in urban settings, relatively little research has been conducted in rural settings. The resulting research gap prohibits a comprehensive understanding and application of solutions for active living in rural America. Therefore, the purpose of this paper was to assess the evidence-base for an ecological model of active living for rural populations and outline key scientific gaps that inhibit the development and application of solutions. Specifically, we reexamined the four domains conceptualized by the model and suggest there is a dearth of research specific to rural communities across all areas of the framework. Considering the limited rural-specific efforts, we propose areas that need addressing in order to mobilize rural active living researchers and practitioners into action. PMID:26327514

Applications of ultrasensitive magnetic measurement technologies (invited) (abstract)

NASA Astrophysics Data System (ADS)

Hirschkoff, Eugene C.

1993-05-01

The development of reliable, easy-to-use magnetic measurement systems with significantly enhanced levels of sensitivity has opened up a number of broad new areas of application for magnetic sensing. Magnetometers based on optical pumping offer sensitivities at the picotesla level, while those that utilize superconducting quantum interference devices can operate at the femtotesla level. These systems are finding applications in areas as diverse as geophysical exploration, communications, and medical diagnostics. This review briefly surveys the capabilities and application areas for a number of magnetic sensing technologies. The emphasis then focuses on the application of the most sensitive of these to the field of medical diagnostics and functional imaging. Protocols for specific applications to noninvasive presurgical planning and to the noninvasive assay of cortical dysfunction in diseases ranging from epilepsy to migraine and schizophrenia will be described in detail. Data will be presented reporting independent validation of these techniques in ten patients who subsequently underwent surgery. Routine and reliable utilization of this ultrasensitive magnetic sensing technology in the clinic is now feasible and practical.

Methods to estimate total forest biomass for extensive forest inventories: applications in the northeastern U.S.

Treesearch

Eric H. Wharton; Douglas M. Griffith

1993-01-01

Presents methods for synthesizing information from existing biomass literature when making biomass assessments over extensive geographic areas, such as for a state or region. Described are general applications to the northeastern United States, and specific applications to Ohio. Tables of appropriate regression equations and the tree and shrub species to which these...

40 CFR 124.42 - Additional procedures for PSD permits affecting Class I areas.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 21 2010-07-01 2010-07-01 false Additional procedures for PSD permits... (CONTINUED) WATER PROGRAMS PROCEDURES FOR DECISIONMAKING Specific Procedures Applicable to PSD Permits § 124.42 Additional procedures for PSD permits affecting Class I areas. (a) The Regional Administrator...

40 CFR 124.42 - Additional procedures for PSD permits affecting Class I areas.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 23 2013-07-01 2013-07-01 false Additional procedures for PSD permits... (CONTINUED) WATER PROGRAMS PROCEDURES FOR DECISIONMAKING Specific Procedures Applicable to PSD Permits § 124.42 Additional procedures for PSD permits affecting Class I areas. (a) The Regional Administrator...

40 CFR 124.42 - Additional procedures for PSD permits affecting Class I areas.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 22 2011-07-01 2011-07-01 false Additional procedures for PSD permits... (CONTINUED) WATER PROGRAMS PROCEDURES FOR DECISIONMAKING Specific Procedures Applicable to PSD Permits § 124.42 Additional procedures for PSD permits affecting Class I areas. (a) The Regional Administrator...

40 CFR 124.42 - Additional procedures for PSD permits affecting Class I areas.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 23 2012-07-01 2012-07-01 false Additional procedures for PSD permits... (CONTINUED) WATER PROGRAMS PROCEDURES FOR DECISIONMAKING Specific Procedures Applicable to PSD Permits § 124.42 Additional procedures for PSD permits affecting Class I areas. (a) The Regional Administrator...

40 CFR 124.42 - Additional procedures for PSD permits affecting Class I areas.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 22 2014-07-01 2013-07-01 true Additional procedures for PSD permits... (CONTINUED) WATER PROGRAMS PROCEDURES FOR DECISIONMAKING Specific Procedures Applicable to PSD Permits § 124.42 Additional procedures for PSD permits affecting Class I areas. (a) The Regional Administrator...

Computer Applications in Instruction: A Teacher's Guide to Selection and Use.

ERIC Educational Resources Information Center

Edwards, Judith B.; And Others

Intended for upper elementary and secondary teachers in all subject areas, this guide provides practical advice on determining the appropriate application of computer technology and on the selection of specific, subject-related computer-based instruction units. Under the heading of hardware and software, topics discussed include communicating with…

13 CFR 125.5 - Certificate of Competency Program.

Code of Federal Regulations, 2010 CFR

2010-01-01

... the type of product being procured or the specific contract at issue. (iv) A non-manufacturer making... application. (1) The COC review process is not limited to the areas of nonresponsibility cited by the contracting officer. SBA may, at its discretion, independently evaluate the COC applicant for all elements of...

Recycling research progress at the Forest Products Laboratory.

Treesearch

1995-01-01

This document summarizes accomplishments of USDA Forest Service researchers in the area of recycling. Specifically, it describes work in economic assessment, paper recycling, recycled housing and industrial applications of recycled materials, other recycling applications, and technology transfer. The literature list includes the references cited in the text and...

Development and application of air quality models at the US ...

EPA Pesticide Factsheets

Overview of the development and application of air quality models at the U.S. EPA, particularly focused on the development and application of the Community Multiscale Air Quality (CMAQ) model developed within the Computation Exposure Division (CED) of the National Exposure Research Laboratory (NERL). This presentation will provide a simple overview of air quality model development and application geared toward a non-technical student audience. The National Exposure Research Laboratory (NERL) Computational Exposure Division (CED) develops and evaluates data, decision-support tools, and models to be applied to media-specific or receptor-specific problem areas. CED uses modeling-based approaches to characterize exposures, evaluate fate and transport, and support environmental diagnostics/forensics with input from multiple data sources. It also develops media- and receptor-specific models, process models, and decision support tools for use both within and outside of EPA.

Development of a Model for the Representation of Nanotechnology-Specific Terminology

PubMed Central

Bailey, LeeAnn O.; Kennedy, Christopher H.; Fritts, Martin J.; Hartel, Francis W.

2006-01-01

Nanotechnology is an important, rapidly-evolving, multidisciplinary field [1]. The tremendous growth in this area necessitates the establishment of a common, open-source terminology to support the diverse biomedical applications of nanotechnology. Currently, the consensus process to define and categorize conceptual entities pertaining to nanotechnology is in a rudimentary stage. We have constructed a nanotechnology-specific conceptual hierarchy that can be utilized by end users to retrieve accurate, controlled terminology regarding emerging nanotechnology and corresponding clinical applications. PMID:17238469

Pyrolytic synthesis and characterization of N-doped carbon nanoflakes for electrochemical applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Savilov, S.V., E-mail: savilov@chem.msu.ru; N.S. Kurnakov Institute of General and Inorganic Chemistry Of Russian Academy of Sciences, Leninsky avenue, 31, Moscow 119991; Arkhipova, E.A.

2015-09-15

Highlights: • Carbon nanoflakes doped with nitrogen were produced by a pyrolytic technique. • Quarternary, pyrrolic and pyridinic types of nitrogen are confirmed by XPS. • Nitrogen content depends on precursor used and temperature processed. • Specific surface area values decrease with increasing of synthesis duration. • N-doped carbon nanoflakes may be suitable for electrochemical applications. - Abstract: Nitrogen doped carbon nanoflakes, which are very important for many electrochemical applications, were synthesized by pyrolysis of nitrogen containing organic compounds over metal oxide template. Acetonitrile, pyridine and butylamine, which are of different volatility were tested as N-containing precursors. Morphology, structure andmore » chemical composition of the as-synthesized materials were investigated by scanning electron microscopy (SEM), high resolution transmission electron microscopy (TEM), Raman spectroscopy and X-ray photoelectron spectroscopy (XPS). It was found that materials are highly defective and consist of a few malformed graphene layers. X-ray photoelectron spectra reflect the dominant graphitic and pyridinic N-bonding configuration. It was also noted that specific surface area depends on the duration and temperature of the reaction. Increase in duration and temperature led to decrease of the specific surface area from 1000 to 160 m{sup 2}/g, 1170 to 210 m{sup 2}/g and 1180 to 480 m{sup 2}/g for acetonitrile, butylamine and pyridine precursors, respectively.« less

Sensor Fusion and Smart Sensor in Sports and Biomedical Applications

PubMed Central

Mendes, José Jair Alves; Vieira, Mário Elias Marinho; Pires, Marcelo Bissi; Stevan, Sergio Luiz

2016-01-01

The following work presents an overview of smart sensors and sensor fusion targeted at biomedical applications and sports areas. In this work, the integration of these areas is demonstrated, promoting a reflection about techniques and applications to collect, quantify and qualify some physical variables associated with the human body. These techniques are presented in various biomedical and sports applications, which cover areas related to diagnostics, rehabilitation, physical monitoring, and the development of performance in athletes, among others. Although some applications are described in only one of two fields of study (biomedicine and sports), it is very likely that the same application fits in both, with small peculiarities or adaptations. To illustrate the contemporaneity of applications, an analysis of specialized papers published in the last six years has been made. In this context, the main characteristic of this review is to present the largest quantity of relevant examples of sensor fusion and smart sensors focusing on their utilization and proposals, without deeply addressing one specific system or technique, to the detriment of the others. PMID:27669260

Reuse: A knowledge-based approach

NASA Technical Reports Server (NTRS)

Iscoe, Neil; Liu, Zheng-Yang; Feng, Guohui

1992-01-01

This paper describes our research in automating the reuse process through the use of application domain models. Application domain models are explicit formal representations of the application knowledge necessary to understand, specify, and generate application programs. Furthermore, they provide a unified repository for the operational structure, rules, policies, and constraints of a specific application area. In our approach, domain models are expressed in terms of a transaction-based meta-modeling language. This paper has described in detail the creation and maintenance of hierarchical structures. These structures are created through a process that includes reverse engineering of data models with supplementary enhancement from application experts. Source code is also reverse engineered but is not a major source of domain model instantiation at this time. In the second phase of the software synthesis process, program specifications are interactively synthesized from an instantiated domain model. These specifications are currently integrated into a manual programming process but will eventually be used to derive executable code with mechanically assisted transformations. This research is performed within the context of programming-in-the-large types of systems. Although our goals are ambitious, we are implementing the synthesis system in an incremental manner through which we can realize tangible results. The client/server architecture is capable of supporting 16 simultaneous X/Motif users and tens of thousands of attributes and classes. Domain models have been partially synthesized from five different application areas. As additional domain models are synthesized and additional knowledge is gathered, we will inevitably add to and modify our representation. However, our current experience indicates that it will scale and expand to meet our modeling needs.

78 FR 36822 - Special Permit Applications

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-19

... Specification salvage cylinders. 15779-N Patterson Logistics 49 CFR 173.304a......... To authorize the Services... areas of the US only, without being subject to hazard communication requirements, quantity limitations...

Enhanced glucose biosensor properties of gold nanoparticle-decorated ZnO nanorods

NASA Astrophysics Data System (ADS)

Wang, Zi-Hao; Yang, Chih-Chiang; Su, Yan-Kuin; Ruand, Jian-Long

2017-04-01

As new materials have been reported and more knowledge on detailed mechanism of glucose oxidation has been unveiled, the non-enzymatic glucose sensor keeps coming closer to practical applications. Nanostructures with higher surface specific area has great potential applications in sensing devices ZnO nanoords were synthesized in a hydrothermal method using simply available laboratory chemicals. Results showed that as-synthesized Gold Nanoparticle-decorated ZnO Nanorods possessing higher specific surface area, significantly increased the non-enzyme efficiency which in turn improved the sensing performances. The electrode also demonstrated excellent performance in sensing glucose concentration with remarkable sensitivity (46.6 μA/mM-cm2) and good repeatability. This work is expected to open a new avenue to fabricate non-enzymatic electrochemical sensors of glucose involving co-mediating.

Fluvial sediment fingerprinting: literature review and annotated bibliography

USGS Publications Warehouse

Williamson, Joyce E.; Haj, Adel E.; Stamm, John F.; Valder, Joshua F.; Prautzch, Vicki L.

2014-01-01

The U.S. Geological Survey has evaluated and adopted various field methods for collecting real-time sediment and nutrient data. These methods have proven to be valuable representations of sediment and nutrient concentrations and loads but are not able to accurately identify specific source areas. Recently, more advanced data collection and analysis techniques have been evaluated that show promise in identifying specific source areas. Application of field methods could include studies of sources of fluvial sediment, otherwise referred to as sediment “fingerprinting.” The identification of sediment is important, in part, because knowing the primary sediment source areas in watersheds ensures that best management practices are incorporated in areas that maximize reductions in sediment loadings. This report provides a literature review and annotated bibliography of existing methodologies applied in the field of fluvial sediment fingerprinting. This literature review provides a bibliography of publications where sediment fingerprinting methods have been used; however, this report is not assumed to provide an exhaustive listing. Selected publications were categorized by methodology with some additional summary information. The information contained in the summary may help researchers select methods better suited to their particular study or study area, and identify methods in need of more testing and application.

High surface area electrodes by template-free self-assembled hierarchical porous gold architecture.

PubMed

Morag, Ahiud; Golub, Tatiana; Becker, James; Jelinek, Raz

2016-06-15

The electrode active surface area is a crucial determinant in many electrochemical applications and devices. Porous metal substrates have been employed in electrode design, however construction of such materials generally involves multistep processes, generating in many instances electrodes exhibiting incomplete access to internal pore surfaces. Here we describe fabrication of electrodes comprising hierarchical, nano-to-microscale porous gold matrix, synthesized through spontaneous crystallization of gold thiocyanate in water. Cyclic voltammetry analysis revealed that the specific surface area of the conductive nanoporous Au microwires was very high and depended only upon the amount of gold used, not electrode areas or geometries. Application of the electrode in a pseudo-capacitor device is presented. Copyright © 2016 Elsevier Inc. All rights reserved.

Costs and benefits

NASA Technical Reports Server (NTRS)

1975-01-01

Two models of cost benefit analysis are illustrated and the application of these models to assessing the economic scope of space applications programs was discussed. Four major areas cited as improvable through space derived information - food supply and distribution, energy sources, mineral reserves, and communication and navigation were - discussed. Specific illustrations are given for agriculture and maritime traffic.

75 FR 12272 - Notice of Availability of Funds and Solicitation for Grant Applications (SGA) for Community-Based...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-15

... provide specific types of training services. All projects must lead to employment for program participants... services offered by the CBJT grant. Further, we encourage applicants to use program models with...; and (2) the training is offered in partnership with a community college outside the underserved area...

7 CFR 1470.20 - Application for contracts and selecting offers from applicants.

Code of Federal Regulations, 2010 CFR

2010-01-01

... research and demonstration activities or for pilot testing, describes the nature of the research... represents the least cost to the program will be given higher priority. (4) The State Conservationist or... priority resource concerns for a State, or the specific geographic areas within a State, with advice from...

Enzymes from Extreme Environments and Their Industrial Applications

PubMed Central

Littlechild, Jennifer A.

2015-01-01

This article will discuss the importance of specific extremophilic enzymes for applications in industrial biotechnology. It will specifically address those enzymes that have applications in the area of biocatalysis. Such enzymes now play an important role in catalyzing a variety of chemical conversions that were previously carried out by traditional chemistry. The biocatalytic process is carried out under mild conditions and with greater specificity. The enzyme process does not result in the toxic waste that is usually produced in a chemical process that would require careful disposal. In this sense, the biocatalytic process is referred to as carrying out “green chemistry” which is considered to be environmentally friendly. Some of the extremophilic enzymes to be discussed have already been developed for industrial processes such as an l-aminoacylase and a γ-lactamase. The industrial applications of other extremophilic enzymes, including transaminases, carbonic anhydrases, dehalogenases, specific esterases, and epoxide hydrolases, are currently being assessed. Specific examples of these industrially important enzymes that have been studied in the authors group will be presented in this review. PMID:26528475

22 CFR 216.2 - Applicability of procedures.

Code of Federal Regulations, 2011 CFR

2011-04-01

... confined to small areas and carefully monitored; (iii) Analyses, studies, academic or research workshops... details of the specific activities conducted by the PVO; (xiv) Studies, projects or programs intended to...

Linear polarizer local characterizations by polarimetric imaging for applications to polarimetric sensors for torque measurement for hybrid cars

NASA Astrophysics Data System (ADS)

Georges, F.; Remouche, M.; Meyrueis, P.

2011-06-01

Usually manufacturer's specifications do not deal with the ability of linear sheet polarizers to have a constant transmittance function over their geometric area. These parameters are fundamental for developing low cost polarimetric sensors(for instance rotation, torque, displacement) specifically for hybrid car (thermic + electricity power). It is then necessary to specially characterize commercial polarizers sheets to find if they are adapted to this kind of applications. In this paper, we present measuring methods and bench developed for this purpose, and some preliminary characterization results. We state conclusions for effective applications to hybrid car gearbox control and monitoring.

Advanced high-temperature batteries

NASA Technical Reports Server (NTRS)

Nelson, P. A.

1989-01-01

Recent results for Li-Al/FeS2 cells and bipolar battery design have shown the possibility of achieving high specific energy (210 Wh/kg) and high specific power (239 W/kg) at the cell level for an electric vehicle application. Outstanding performance is also projected for sodium/metal chloride cells having large electrolyte areas and thin positive electrodes.

Smart Materials Based on DNA Aptamers: Taking Aptasensing to the Next Level

PubMed Central

Mastronardi, Emily; Foster, Amanda; Zhang, Xueru; DeRosa, Maria C.

2014-01-01

“Smart” materials are an emerging category of multifunctional materials with physical or chemical properties that can be controllably altered in response to an external stimulus. By combining the standard properties of the advanced material with the unique ability to recognize and adapt in response to a change in their environment, these materials are finding applications in areas such as sensing and drug delivery. While the majority of these materials are responsive to physical or chemical changes, a particularly exciting area of research seeks to develop smart materials that are sensitive to specific molecular or biomolecular stimuli. These systems require the integration of a molecular recognition probe specific to the target molecule of interest. The ease of synthesis and labeling, low cost, and stability of DNA aptamers make them uniquely suited to effectively serve as molecular recognition probes in novel smart material systems. This review will highlight current work in the area of aptamer-based smart materials and prospects for their future applications. PMID:24553083

Small ICBM area narrowing report. Volume 3: Hard silo in patterned array basing mode

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The purpose of this report is to identify those areas that could potentially support deployment of the Small Intercontinental Ballistic Missile (ICBM) utilizing basing modes presently considered viable: the Hard Mobile Launcher in Random Movement, the Hard Mobile Launcher at Minuteman Facilities, or the Hard Silo in Patterned Array. Specifically, this report describes the process and the rationale supporting the application of Exclusionary and Evaluative Criteria and lists those locations that were eliminated through the application of these criteria. The remaining locations will be the subject of further investigations.

Physiology, biochemistry and possible applications of microbial caffeine degradation.

PubMed

Gummadi, Sathyanarayana N; Bhavya, B; Ashok, Nandhini

2012-01-01

Caffeine, a purine alkaloid is a constituent of widely consumed beverages. The scientific evidence which has proved the harm of this alkaloid has paved the way for innumerable research in the area of caffeine degradation. In addition to this, the fact that the by-products of the coffee and tea industry pollute the environment has called for the need of decaffeinating coffee and tea industry's by-products. Though physical and chemical methods for decaffeination are available, the lack of specificity for removal of caffeine in these techniques and their non-eco-friendly nature has opened the area of microbial and enzymatic degradation of caffeine. Another important application of microbial caffeine degradation apart from its advantages like specificity, eco-friendliness and cost-effectiveness is the fact that this process will enable the production of industrially and medically useful components of the caffeine degradation pathway like theobromine and theophylline. This is a comprehensive review which mainly focuses on caffeine degradation, large-scale degradation of the same and its applications in the industrial world.

Metal-Coated Optical Fibers for High Temperature Applications

NASA Technical Reports Server (NTRS)

Zeakes, Jason; Murphy, Kent; Claus, Richard; Greene, Jonathan; Tran, Tuan

1996-01-01

This poster will highlight on-going research at the Virginia Tech Fiber & Electro-Optics Research Center (FEORC) in the area of thin films on optical fibers. Topics will include the sputter deposition of metals and metal; alloys onto optical fiber and fiber optic sensors for innovative applications. Specific information will be available on thin film fiber optic hydrogen sensors, corrosion sensors, and metal-coated optical fiber for high temperature aerospace applications.

Electric double-layer capacitors based on highly graphitized nanoporous carbons derived from ZIF-67.

PubMed

Torad, Nagy L; Salunkhe, Rahul R; Li, Yunqi; Hamoudi, Hicham; Imura, Masataka; Sakka, Yoshio; Hu, Chi-Chang; Yamauchi, Yusuke

2014-06-23

Nanoporous carbons (NPCs) have large specific surface areas, good electrical and thermal conductivity, and both chemical and mechanical stability, which facilitate their use in energy storage device applications. In the present study, highly graphitized NPCs are synthesized by one-step direct carbonization of cobalt-containing zeolitic imidazolate framework-67 (ZIF-67). After chemical etching, the deposited Co content can be completely removed to prepare pure NPCs with high specific surface area, large pore volume, and intrinsic electrical conductivity (high content of sp(2) -bonded carbons). A detailed electrochemical study is performed using cyclic voltammetry and galvanostatic charge-discharge measurements. Our NPC is very promising for efficient electrodes for high-performance supercapacitor applications. A maximum specific capacitance of 238 F g(-1) is observed at a scan rate of 20 mV s(-1) . This value is very high compared to previous works on carbon-based electric double layer capacitors. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Urban Rail Supporting Technology Program Fiscal Year 1974 Year End Summary

DOT National Transportation Integrated Search

1975-03-01

Major areas include program management, technical support and application engineering, facilities development, test and evaluation, and technology development. Specific technical discussion includes track measurement systems; UMTA facilities developm...

Quantification of changes in language-related brain areas in autism spectrum disorders using large-scale network analysis.

PubMed

Goch, Caspar J; Stieltjes, Bram; Henze, Romy; Hering, Jan; Poustka, Luise; Meinzer, Hans-Peter; Maier-Hein, Klaus H

2014-05-01

Diagnosis of autism spectrum disorders (ASD) is difficult, as symptoms vary greatly and are difficult to quantify objectively. Recent work has focused on the assessment of non-invasive diffusion tensor imaging-based biomarkers that reflect the microstructural characteristics of neuronal pathways in the brain. While tractography-based approaches typically analyze specific structures of interest, a graph-based large-scale network analysis of the connectome can yield comprehensive measures of larger-scale architectural patterns in the brain. Commonly applied global network indices, however, do not provide any specificity with respect to functional areas or anatomical structures. Aim of this work was to assess the concept of network centrality as a tool to perform locally specific analysis without disregarding the global network architecture and compare it to other popular network indices. We create connectome networks from fiber tractographies and parcellations of the human brain and compute global network indices as well as local indices for Wernicke's Area, Broca's Area and the Motor Cortex. Our approach was evaluated on 18 children suffering from ASD and 18 typically developed controls using magnetic resonance imaging-based cortical parcellations in combination with diffusion tensor imaging tractography. We show that the network centrality of Wernicke's area is significantly (p<0.001) reduced in ASD, while the motor cortex, which was used as a control region, did not show significant alterations. This could reflect the reduced capacity for comprehension of language in ASD. The betweenness centrality could potentially be an important metric in the development of future diagnostic tools in the clinical context of ASD diagnosis. Our results further demonstrate the applicability of large-scale network analysis tools in the domain of region-specific analysis with a potential application in many different psychological disorders.

Study of the Application of Separation Control by Unsteady Excitation to Civil Transport Aircraft

NASA Technical Reports Server (NTRS)

McLean, J. D.; Crouch, J. D.; Stoner, R. C.; Sakurai, S.; Seidel, G. E.; Feifel, W. M.; Rush, H. M.

1999-01-01

This study provides a preliminary assessment of the potential benefits of applying unsteady separation control to transport aircraft. Estimates are given for some of the costs associated with a specific application to high-lift systems. High-leverage areas for future research were identified during the course of the study. The study was conducted in three phases. Phase 1 consisted of a coarse screening of potential applications within the aerodynamics discipline. Potential benefits were identified and in some cases quantified in a preliminary way. Phase 2 concentrated on the application to the wing high-lift system, deemed to have the greatest potential benefit for commercial transports. A team of experts, including other disciplines (i.e. hydraulic, mechanical, and electrical systems, structures, configurations, manufacturing, and finance), assessed the feasibility, benefits, and costs to arrive at estimates of net benefits. In both phases of the study, areas of concern and areas for future research were identified. In phase 3 of this study, the high-leverage areas for future research were prioritized as a guide for future efforts aimed at the application of active flow control to commercial transport aircraft.

E-Education Applications: Human Factors and Innovative Approaches

ERIC Educational Resources Information Center

Ghaoui, Claude, Ed.

2004-01-01

"E-Education Applications: Human Factors and Innovative Approaches" enforces the need to take multi-disciplinary and/or inter-disciplinary approaches, when solutions for e-education (or online-, e-learning) are introduced. By focusing on the issues that have impact on the usability of e-learning, the book specifically fills-in a gap in this area,…

The General Concept of Benchmarking and Its Application in Higher Education in Europe

ERIC Educational Resources Information Center

Nazarko, Joanicjusz; Kuzmicz, Katarzyna Anna; Szubzda-Prutis, Elzbieta; Urban, Joanna

2009-01-01

The purposes of this paper are twofold: a presentation of the theoretical basis of benchmarking and a discussion on practical benchmarking applications. Benchmarking is also analyzed as a productivity accelerator. The authors study benchmarking usage in the private and public sectors with due consideration of the specificities of the two areas.…

Sulfur-doped nanoporous carbon spheres with ultrahigh specific surface area and high electrochemical activity for supercapacitor

NASA Astrophysics Data System (ADS)

Liu, Simin; Cai, Yijin; Zhao, Xiao; Liang, Yeru; Zheng, Mingtao; Hu, Hang; Dong, Hanwu; Jiang, Sanping; Liu, Yingliang; Xiao, Yong

2017-08-01

Development of facile and scalable synthesis process for the fabrication of nanoporous carbon materials with large specific surface areas, well-defined nanostructure, and high electrochemical activity is critical for the high performance energy storage applications. The key issue is the dedicated balance between the ultrahigh surface area and highly porous but interconnected nanostructure. Here, we demonstrate the fabrication of new sulfur doped nanoporous carbon sphere (S-NCS) with the ultrahigh surface area up to 3357 m2 g-1 via a high-temperature hydrothermal carbonization and subsequent KOH activation process. The as-prepared S-NCS which integrates the advantages of ultrahigh porous structure, well-defined nanospherical and modification of heteroatom displays excellent electrochemical performance. The best performance is obtained on S-NCS prepared by the hydrothermal carbonization of sublimed sulfur and glucose, S-NCS-4, reaching a high specific capacitance (405 F g-1 at a current density of 0.5 A g-1) and outstanding cycle stability. Moreover, the symmetric supercapacitor is assembled by S-NCS-4 displays a superior energy density of 53.5 Wh kg-1 at the power density of 74.2 W kg-1 in 1.0 M LiPF6 EC/DEC. The synthesis method is simple and scalable, providing a new route to prepare highly porous and heteroatom-doped nanoporous carbon spheres for high performance energy storage applications.

Spacecraft applications of advanced global positioning system technology

NASA Technical Reports Server (NTRS)

Huth, Gaylord; Dodds, James; Udalov, Sergei; Austin, Richard; Loomis, Peter; Duboraw, I. Newton, III

1988-01-01

The purpose of this study was to evaluate potential uses of Global Positioning System (GPS) in spacecraft applications in the following areas: attitude control and tracking; structural control; traffic control; and time base definition (synchronization). Each of these functions are addressed. Also addressed are the hardware related issues concerning the application of GPS technology and comparisons are provided with alternative instrumentation methods for specific functions required for an advanced low earth orbit spacecraft.

The Natural Helmholtz-Hodge Decomposition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bhatia, H.

nHHD is a C++ library to decompose a flow field into three components exhibiting specific types of behaviors. These components allow more targeted analysis of flow behavior and can be applied to a variety of application areas.

TRI.NET Tutorial with Examples

EPA Pesticide Factsheets

This tutorial walks users through some sample TRI.NET searches to illustrate some of the ways this application can be used to access TRI data and answer basic questions about toxic chemical releases in a specific geographic area.

Procedure M - A framework for stratified area estimation. [in multispectral scanner data processing

NASA Technical Reports Server (NTRS)

Kauth, R. J.; Cicone, R. C.; Malila, W. A.

1980-01-01

This paper describes Procedure M, a systematic approach to processing multispectral scanner data for classification and acreage estimation. A general discussion of the rationale and development of the procedure is given in the context of large-area agricultural applications. Specific examples are given in the form of test results on acreage estimation of spring small grains.

Defining values in place: A practical application for visitor management in protected areas

Treesearch

Gordon Cessford; Mike Edginton

2007-01-01

This paper explores a value specification option to better meet a core information need in protected area management for recreation and conservation. It does not debate the meaning or definition of values, but instead identifies a perspective on values that is aimed at meeting practical conservation management needs. The first part of that perspective involves...

Selective herbicide applications for low impact vegetation management of exotic species and enhancement of native plant communities

Treesearch

Max Williamson

1998-01-01

Selective and specific management for the control of exotic (non-native) plants is necessary for preservation of native plant communities. Managers of federal, state, or county land holdings and parks, wildlife areas, recreation areas, and historic sites are frequently charged with selectively managing the enhancement of desirable or native plant communities. In...

Analysis of Wear Behavior of Graphene OXIDE — Polyamide Gears for Engineering Applications

NASA Astrophysics Data System (ADS)

Rajamani, Geetha; Paulraj, Jawahar; Krishnan, Kanny

Recent advances in polymer nanocomposites open a wide range of applications in various industrial sectors. Due to their high potential properties, these materials are replacing the usage of metals for many heavier components in automobile industries. In this experimental work, the tribological performance of Graphene oxide (GO) — Polyamide is investigated against pristine polyamide by fabricating gears for the usage in engineering applications. A gear test rig was developed in-house for analysis to study the specific wear rate and temperature gradient at different conditions of load and speeds. The wear resistance of the polyamide gears with the addition of 0.03wt.% of graphene oxide is better than the pristine polyamide gears and the specific wear rate is reduced significantly. The reduced specific wear rate of these polymer nanocomposite gears is attributed to the superior properties of graphene oxide such as High specific surface area, good adhesion properties and enhanced glass transition temperatures. The GO nanocomposite gear seems to be a potential alternative against conventional gears for engineering applications. Finally, the wear mechanisms and the potential of GO-based polyamide nanocomposite gears were proposed tentatively in the development of transmission gears for engineering applications.

Soil Organic Matter (SOM): Molecular Simulations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Andersen, Amity

Molecular simulation is a powerful tool used to gain an atomistic, molecular, and nanoscale level understanding of the structure, dynamics, and interactions from adsorption on minerals and assembly in aggregates of soil organic matter (SOM). Given the importance of SOM fate and persistence in soils and the current knowledge gaps, applications of atomistic scale simulations to study the complex compounds in SOM and their interactions in self-assembled aggregates composed of different organic matter compounds and with mineral surfaces of different types common in soils are few and far between. Here, we describe various molecular simulation methods that are currently inmore » use in various areas and applicable to SOM research, followed by a brief survey of specific applications to SOM research and an illustration with our own recent efforts in this area. We conclude with an outlook and the challenges for future research in this area.« less

Small ICBM area narrowing report. Volume 1. Hard mobile launcher in random movement basing mode

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The purpose of this report is to identify those areas that could potentially support deployment of the Small Intercontinental Ballistic Missile (ICBM) utilizing basing modes presently considered viable: the Hard Mobile Launcher in Random Movement, the Hard Mobile Launcher at Minuteman Facilities, and the Hard Silo in Patterned Array. Specifically, this report describes the process and the rationale supporting the application of Exclusionary and Evaluative Criteria and lists those locations that were eliminated through the application of these criteria. The remaining locations will be the subject of further investigations.

Small ICBM area narrowing report. Volume 2. Hard mobile launcher at minuteman facilities basing mode

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The purpose of this report is to identify those areas that could potentially support deployment of the Small Intercontinental Ballistic Missile (ICBM) utilizing basing modes presently considered viable: the Hard Mobile Launcher in Random Movement, the Hard Mobile Launcher at Minuteman Facilities, and the Hard Silo in Patterned Array. Specifically, this report describes the process and the rationale supporting the application of Exclusionary and Evaluative Criteria and lists those locations that were eliminated through the application of these criteria. The remaining locations will be the subject of further investigations.

The new applications of sputtering and ion plating

NASA Technical Reports Server (NTRS)

Spalvins, T.

1977-01-01

The potential industrial applications of sputtering and ion plating are strictly governed by the unique features these methods possess. The outstanding features of each method, the resultant coating characteristics and the various sputtering modes and configurations are discussed. New, more complex coatings and deposits can be developed such as graded composition structures (metal-ceramic seals), laminated and dispersion strengthened composites which improve the mechanical properties and high temperature stability. Specific industrial areas where future effort of sputtering and ion plating will concentrate to develop intricate alloy or compound coatings and solve difficult problem areas are discussed.

Environmental databases and other computerized information tools

NASA Technical Reports Server (NTRS)

Clark-Ingram, Marceia

1995-01-01

Increasing environmental legislation has brought about the development of many new environmental databases and software application packages to aid in the quest for environmental compliance. These databases and software packages are useful tools and applicable to a wide range of environmental areas from atmospheric modeling to materials replacement technology. The great abundance of such products and services can be very overwhelming when trying to identify the tools which best meet specific needs. This paper will discuss the types of environmental databases and software packages available. This discussion will also encompass the affected environmental areas of concern, product capabilities, and hardware requirements for product utilization.

The thermal stability and catalytic application of manganese oxide-zirconium oxide powders

NASA Astrophysics Data System (ADS)

Zhao, Qiang

MnOx-ZrO2 mixed oxide is an active catalyst for combustion, oxidation, and oxygen storage applications. MnOx-ZrO 2 mixture also has large reversible adsorption capability for NO x, which makes it a promising candidate for NOx abatement in automobile emission control. However, MnOx-ZrO 2 mixed oxide has not been used extensively because the processing and the thermal stability of resulting powders have not been studied systematically. It is critical to have thermally stable catalytic material because the application temperature can reach as high as 1000°C during service. In this study, we focused on improving the thermal stability of oxide powders, such as MnO x, ZrO2, and MnOx-ZrO2, by controlling the processing methods and parameters. For pure MnOx made from the precipitation method using Mn(NO3)2 aqueous solution and ammonium hydroxide, we found that lower concentration of Mn(NO3) 2 solution and larger amount of ammonium hydroxide resulted in higher surface area powders. For pure ZrO2, we found curing hydrous zirconia in the mother liquid produced ZrO2 powders with larger pore volume and pore size. The specific surface area was also significantly enhanced by curing for the synthesized powders before calcination or after low temperature calcinations, and this improvement could be preserved to high temperatures if SiO2 was doped in ZrO2. A Monte Carlo simulation model examining the effect of primary particle packing on the specific surface area was used to explain the curing result. MnOx-ZrO2 mixtures had higher surface area than the single component oxide at 500 and 700°C because composite powders sintered less. The sintering behavior of composite powders at 900°C was opposite to that at 500°C and the specific surface area of MnOx-ZrO2 decreased drastically at 900°C. Curing ZrO2 first or using La dopant could significantly enhance the specific surface area of MnOx-ZrO2 at 900°C. Through the tests of the redox property and NO storage capability we found a close relationship between the enhanced thermal stability and better catalytic performance.

Where can pixel counting area estimates meet user-defined accuracy requirements?

NASA Astrophysics Data System (ADS)

Waldner, François; Defourny, Pierre

2017-08-01

Pixel counting is probably the most popular way to estimate class areas from satellite-derived maps. It involves determining the number of pixels allocated to a specific thematic class and multiplying it by the pixel area. In the presence of asymmetric classification errors, the pixel counting estimator is biased. The overarching objective of this article is to define the applicability conditions of pixel counting so that the estimates are below a user-defined accuracy target. By reasoning in terms of landscape fragmentation and spatial resolution, the proposed framework decouples the resolution bias and the classifier bias from the overall classification bias. The consequence is that prior to any classification, part of the tolerated bias is already committed due to the choice of the spatial resolution of the imagery. How much classification bias is affordable depends on the joint interaction of spatial resolution and fragmentation. The method was implemented over South Africa for cropland mapping, demonstrating its operational applicability. Particular attention was paid to modeling a realistic sensor's spatial response by explicitly accounting for the effect of its point spread function. The diagnostic capabilities offered by this framework have multiple potential domains of application such as guiding users in their choice of imagery and providing guidelines for space agencies to elaborate the design specifications of future instruments.

The Development of Wireless Body Area Network for Motion Sensing Application

NASA Astrophysics Data System (ADS)

Puspitaningayu, P.; Widodo, A.; Yundra, E.; Ramadhany, F.; Arianto, L.; Habibie, D.

2018-04-01

The information era has driven the society into the digitally-controlled lifestyle. Wireless body area networks (WBAN) as the specific scope of wireless sensor networks (WSN) is consistently growing into bigger applications. Currently, people are able to monitor their medical parameters by simply using small electronics devices attached to their body and connected to the authorities. On top of that, this time, smart phones are typically equipped with sensors such as accelerometer, gyroscope, barometric pressure, heart rate monitor, etc. It means that the sensing yet the signal processing can be performed by a single device. Moreover, Android opens lot wider opportunities for new applications as the most popular open-sourced smart phone platform. This paper is intended to show the development of motion sensing application which focused on analysing data from accelerometer and gyroscope. Beside reads the sensors, this application also has the ability to convert the sensors’ numerical value into graphs.

Airborne Remote Sensing (ARS) for Agricultural Research and Commercialization Applications

NASA Technical Reports Server (NTRS)

Narayanan, Ram; Bowen, Brent D.; Nickerson, Jocelyn S.

2002-01-01

Tremendous advances in remote sensing technology and computing power over the last few decades are now providing scientists with the opportunity to investigate, measure, and model environmental patterns and processes with increasing confidence. Such advances are being pursued by the Nebraska Remote Sensing Facility, which consists of approximately 30 faculty members and is very competitive with other institutions in the depth of the work that is accomplished. The development of this facility targeted at applications, commercialization, and education programs in the area of precision agriculture provides a unique opportunity. This critical area is within the scope of NASA goals and objectives of NASA s Applications, Technology Transfer, Commercialization, and Education Division and the Earth Science Enterprise. This innovative integration of Aerospace (Aeronautics) Technology Enterprise applications with other NASA enterprises serves as a model of cross-enterprise transfer of science with specific commercial applications.

Compound-specific stable carbon isotope composition as a fingerprint for sediment transport: Reproducibility, homogeneity and application in a catchment of the Swiss plateau.

NASA Astrophysics Data System (ADS)

Birkholz, Axel; Niemann, Helge; Alewell, Christine

2014-05-01

A new field for the applications of compound-specific isotope analyses (CSIA) has opened in the recent years. The isotopic signature in fatty acids (FA) can be used to track sediment transport pathways from erosional areas to river systems. In this approach distinct FA d13C values of even numbered saturated and/or unsaturated FAs from soils are traced in suspended river sediments, ie. the place of deposition. CSIA has been shown to be particularly useful in catchment areas with C4 plant crops because, compared to the regularly occurring C3-plants, they are (naturally) depleted in 13C. However, in theory, all plant species even among C3 plants should inherit significant differences in their d13C of FAs. Thus, we tried to differentiate between source areas for suspended sediments from three different land use types: forest (C3 plants), grassland (C3 plants) and arable land (mixture of C3 and C4 plants). Statistical geo software (eg. Isosource) can be used to additionally model the spatial and temporal variability of erosion. We present d13C values of FAs from 8 erosion areas from the Enziwigger catchment of the Swiss plateau (Canton of Lucerne). Each area was assessed through randomised triplicate sampling to test the spatial homogeneity of each one. The homogeneity of a single sample, as well as the reproducibility of our measurements was tested by extracting and analysing the same sample bag in triplicates. We compare compound-specific stable isotope (CSSI) fingerprints of source areas to d13C-values of FAs from suspended sediments of two high-flow events and one base flow period at 3 different sites of the Enziwiger river (upstream, midstream, downstream).

Multi-criteria decision analysis in environmental sciences: ten years of applications and trends.

PubMed

Huang, Ivy B; Keisler, Jeffrey; Linkov, Igor

2011-09-01

Decision-making in environmental projects requires consideration of trade-offs between socio-political, environmental, and economic impacts and is often complicated by various stakeholder views. Multi-criteria decision analysis (MCDA) emerged as a formal methodology to face available technical information and stakeholder values to support decisions in many fields and can be especially valuable in environmental decision making. This study reviews environmental applications of MCDA. Over 300 papers published between 2000 and 2009 reporting MCDA applications in the environmental field were identified through a series of queries in the Web of Science database. The papers were classified by their environmental application area, decision or intervention type. In addition, the papers were also classified by the MCDA methods used in the analysis (analytic hierarchy process, multi-attribute utility theory, and outranking). The results suggest that there is a significant growth in environmental applications of MCDA over the last decade across all environmental application areas. Multiple MCDA tools have been successfully used for environmental applications. Even though the use of the specific methods and tools varies in different application areas and geographic regions, our review of a few papers where several methods were used in parallel with the same problem indicates that recommended course of action does not vary significantly with the method applied. Published by Elsevier B.V.

Application of NASA ERTS-1 satellite imagery in coastal studies

NASA Technical Reports Server (NTRS)

Magoon, O. T.; Berg, D. W. (Principal Investigator); Hallermeier, R. J.

1973-01-01

There are no author-identified significant results in this report. Review of ERTS-1 imagery indicates that it contains information of great value in coastal engineering studies. A brief introduction is given to the methods by which imagery is generated, and examples of its application to coastal engineering. Specific applications discussed include study of the movement of coastal and nearshore sediment-laden water masses and information for planning and construction in remote areas of the world.

Model-Driven Approach for Body Area Network Application Development.

PubMed

Venčkauskas, Algimantas; Štuikys, Vytautas; Jusas, Nerijus; Burbaitė, Renata

2016-05-12

This paper introduces the sensor-networked IoT model as a prototype to support the design of Body Area Network (BAN) applications for healthcare. Using the model, we analyze the synergistic effect of the functional requirements (data collection from the human body and transferring it to the top level) and non-functional requirements (trade-offs between energy-security-environmental factors, treated as Quality-of-Service (QoS)). We use feature models to represent the requirements at the earliest stage for the analysis and describe a model-driven methodology to design the possible BAN applications. Firstly, we specify the requirements as the problem domain (PD) variability model for the BAN applications. Next, we introduce the generative technology (meta-programming as the solution domain (SD)) and the mapping procedure to map the PD feature-based variability model onto the SD feature model. Finally, we create an executable meta-specification that represents the BAN functionality to describe the variability of the problem domain though transformations. The meta-specification (along with the meta-language processor) is a software generator for multiple BAN-oriented applications. We validate the methodology with experiments and a case study to generate a family of programs for the BAN sensor controllers. This enables to obtain the adequate measure of QoS efficiently through the interactive adjustment of the meta-parameter values and re-generation process for the concrete BAN application.

Model-Driven Approach for Body Area Network Application Development

PubMed Central

Venčkauskas, Algimantas; Štuikys, Vytautas; Jusas, Nerijus; Burbaitė, Renata

2016-01-01

This paper introduces the sensor-networked IoT model as a prototype to support the design of Body Area Network (BAN) applications for healthcare. Using the model, we analyze the synergistic effect of the functional requirements (data collection from the human body and transferring it to the top level) and non-functional requirements (trade-offs between energy-security-environmental factors, treated as Quality-of-Service (QoS)). We use feature models to represent the requirements at the earliest stage for the analysis and describe a model-driven methodology to design the possible BAN applications. Firstly, we specify the requirements as the problem domain (PD) variability model for the BAN applications. Next, we introduce the generative technology (meta-programming as the solution domain (SD)) and the mapping procedure to map the PD feature-based variability model onto the SD feature model. Finally, we create an executable meta-specification that represents the BAN functionality to describe the variability of the problem domain though transformations. The meta-specification (along with the meta-language processor) is a software generator for multiple BAN-oriented applications. We validate the methodology with experiments and a case study to generate a family of programs for the BAN sensor controllers. This enables to obtain the adequate measure of QoS efficiently through the interactive adjustment of the meta-parameter values and re-generation process for the concrete BAN application. PMID:27187394

Biotechnological applications of transglutaminases.

PubMed

Rachel, Natalie M; Pelletier, Joelle N

2013-10-22

In nature, transglutaminases catalyze the formation of amide bonds between proteins to form insoluble protein aggregates. This specific function has long been exploited in the food and textile industries as a protein cross-linking agent to alter the texture of meat, wool, and leather. In recent years, biotechnological applications of transglutaminases have come to light in areas ranging from material sciences to medicine. There has also been a substantial effort to further investigate the fundamentals of transglutaminases, as many of their characteristics that remain poorly understood. Those studies also work towards the goal of developing transglutaminases as more efficient catalysts. Progress in this area includes structural information and novel chemical and biological assays. Here, we review recent achievements in this area in order to illustrate the versatility of transglutaminases.

Process for forming a porous silicon member in a crystalline silicon member

DOEpatents

Northrup, M. Allen; Yu, Conrad M.; Raley, Norman F.

1999-01-01

Fabrication and use of porous silicon structures to increase surface area of heated reaction chambers, electrophoresis devices, and thermopneumatic sensor-actuators, chemical preconcentrates, and filtering or control flow devices. In particular, such high surface area or specific pore size porous silicon structures will be useful in significantly augmenting the adsorption, vaporization, desorption, condensation and flow of liquids and gasses in applications that use such processes on a miniature scale. Examples that will benefit from a high surface area, porous silicon structure include sample preconcentrators that are designed to adsorb and subsequently desorb specific chemical species from a sample background; chemical reaction chambers with enhanced surface reaction rates; and sensor-actuator chamber devices with increased pressure for thermopneumatic actuation of integrated membranes. Examples that benefit from specific pore sized porous silicon are chemical/biological filters and thermally-activated flow devices with active or adjacent surfaces such as electrodes or heaters.

ENVIRONMENTAL BIOINFORMATICS AND COMPUTATIONAL TOXICOLOGY CENTER

EPA Science Inventory

The Center activities focused on integrating developmental efforts from the various research projects of the Center, and collaborative applications involving scientists from other institutions and EPA, to enhance research in critical areas. A representative sample of specif...

Technical Mathematics.

ERIC Educational Resources Information Center

Flannery, Carol A.

This manuscript provides information and problems for teaching mathematics to vocational education students. Problems reflect applications of mathematical concepts to specific technical areas. The materials are organized into six chapters. Chapter 1 covers basic arithmetic, including fractions, decimals, ratio and proportions, percentages, and…

Southwest Research Institute assistance to NASA in biomedical areas of the technology utilization program

NASA Technical Reports Server (NTRS)

1973-01-01

Applications of aerospace technology to biomedical science are described. Recent research and development of specific techniques, services, and equipment adopted by physicians to help combat disease and disability are reviewed.

Summary of an integrated ERTS-1 project and its results at the Missouri Geological Survey

NASA Technical Reports Server (NTRS)

Martin, J. A.; Allen, W. H.; Rath, D. L.; Rueff, A.

1974-01-01

Use of the ERTS imagery involved the recognition and interpretation of various ground patterns. Analysis and application are tied to ongoing programs. Specific studies utilizing the imagery and NASA aircraft photography are: a statewide lake and dam inventory; assessment of flooding and floodprone areas along the Missouri portion of the Mississippi and Missouri Rivers; land-use classification for several counties; structural features in selected areas; and Pleistocene features in northern Missouri. Though it has been suggested that repetitive coverage is not necessary for geologic studies, it is this specific feature along with the synoptic view of large portions of the State that provided the potential for the utilization of the ERTS imagery in Missouri. Other State agencies, Departments of Conservation, Agriculture, and Community Affairs, have expressed interest in the potential application of ERTS data in their respective fields.

Study of Federal technology transfer activities in areas of interest to NASA Office of Space and Terrestrial Applications

NASA Technical Reports Server (NTRS)

Madigan, J. A.; Earhart, R. W.

1978-01-01

Forty-three ongoing technology transfer programs in Federal agencies other than NASA were selected from over 200 current Federal technology transfer activities. Selection was made and specific technology transfer mechanisms utilized. Detailed information was obtained on the selected programs by reviewing published literature, and conducting telephone interviews with each program manager. Specific information collected on each program includes technology areas; user groups, mechanisms employed, duration of program, and level of effort. Twenty-four distinct mechanisms are currently employed in Federal technology transfer activities totaling $260 million per year. Typical applications of each mechanism were reviewed, and caveats on evaluating program effectiveness were discussed. A review of recent federally funded research in technology transfer to state and local governments was made utilizing the Smithsonian Science Information Exchange, and abstracts of interest to NASA were selected for further reference.

Motion Trajectories for Wide-area Surveying with a Rover-based Distributed Spectrometer

NASA Technical Reports Server (NTRS)

Tunstel, Edward; Anderson, Gary; Wilson, Edmond

2006-01-01

A mobile ground survey application that employs remote sensing as a primary means of area coverage is highlighted. It is distinguished from mobile robotic area coverage problems that employ contact or proximity-based sensing. The focus is on a specific concept for performing mobile surveys in search of biogenic gases on planetary surfaces using a distributed spectrometer -- a rover-based instrument designed for wide measurement coverage of promising search areas. Navigation algorithms for executing circular and spiral survey trajectories are presented for widearea distributed spectroscopy and evaluated based on area covered and distance traveled.

The European nanometrology landscape.

PubMed

Leach, Richard K; Boyd, Robert; Burke, Theresa; Danzebrink, Hans-Ulrich; Dirscherl, Kai; Dziomba, Thorsten; Gee, Mark; Koenders, Ludger; Morazzani, Valérie; Pidduck, Allan; Roy, Debdulal; Unger, Wolfgang E S; Yacoot, Andrew

2011-02-11

This review paper summarizes the European nanometrology landscape from a technical perspective. Dimensional and chemical nanometrology are discussed first as they underpin many of the developments in other areas of nanometrology. Applications for the measurement of thin film parameters are followed by two of the most widely relevant families of functional properties: measurement of mechanical and electrical properties at the nanoscale. Nanostructured materials and surfaces, which are seen as key materials areas having specific metrology challenges, are covered next. The final section describes biological nanometrology, which is perhaps the most interdisciplinary applications area, and presents unique challenges. Within each area, a review is provided of current status, the capabilities and limitations of current techniques and instruments, and future directions being driven by emerging industrial measurement requirements. Issues of traceability, standardization, national and international programmes, regulation and skills development will be discussed in a future paper.

The European nanometrology landscape

NASA Astrophysics Data System (ADS)

Leach, Richard K.; Boyd, Robert; Burke, Theresa; Danzebrink, Hans-Ulrich; Dirscherl, Kai; Dziomba, Thorsten; Gee, Mark; Koenders, Ludger; Morazzani, Valérie; Pidduck, Allan; Roy, Debdulal; Unger, Wolfgang E. S.; Yacoot, Andrew

2011-02-01

This review paper summarizes the European nanometrology landscape from a technical perspective. Dimensional and chemical nanometrology are discussed first as they underpin many of the developments in other areas of nanometrology. Applications for the measurement of thin film parameters are followed by two of the most widely relevant families of functional properties: measurement of mechanical and electrical properties at the nanoscale. Nanostructured materials and surfaces, which are seen as key materials areas having specific metrology challenges, are covered next. The final section describes biological nanometrology, which is perhaps the most interdisciplinary applications area, and presents unique challenges. Within each area, a review is provided of current status, the capabilities and limitations of current techniques and instruments, and future directions being driven by emerging industrial measurement requirements. Issues of traceability, standardization, national and international programmes, regulation and skills development will be discussed in a future paper.

Proceedings of the 4th International Conference and Exhibition: World Congress on Superconductivity, volume 1

NASA Technical Reports Server (NTRS)

Krishen, Kumar (Editor); Burnham, Calvin (Editor)

1995-01-01

The papers presented at the 4th International Conference Exhibition: World Congress on Superconductivity held at the Marriott Orlando World Center, Orlando, Florida, are contained in this document and encompass the research, technology, applications, funding, political, and social aspects of superconductivity. Specifically, the areas covered included: high-temperature materials; thin films; C-60 based superconductors; persistent magnetic fields and shielding; fabrication methodology; space applications; physical applications; performance characterization; device applications; weak link effects and flux motion; accelerator technology; superconductivity energy; storage; future research and development directions; medical applications; granular superconductors; wire fabrication technology; computer applications; technical and commercial challenges, and power and energy applications.

Wide Bandgap Semiconductor Opportunities in Power Electronics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Das, Sujit; Marlino, Laura D.; Armstrong, Kristina O.

The report objective is to explore the Wide Bandgap (WBG) Power Electronics (PE) market, applications, and potential energy savings in order to identify key areas where further resources and investments of the U.S. Department of Energy’s Office of Energy Efficiency and Renewable Energy (DOE EERE) would have the most impact on U.S. competiveness. After considering the current market, several potential near-term application areas were identified as having significant market and energy savings potential with respect to clean energy applications: (1) data centers (uninterruptible power supplies and server power supplies); (2) renewable energy generation (photovoltaic-solar and wind); (3) motor drives (industrial,more » commercial and residential); (4) rail traction; and, (5) hybrid and electric vehicles (traction and charging). After the initial explorative analyses, it became clear that, SiC, not GaN, would be the principal WBG power device material for the chosen markets in the near future. Therefore, while GaN is discussed when appropriate, this report focuses on SiC devices, other WBG applications (e.g., solid-state transformers, combined heat and power, medical, and wireless power), the GaN market, and GaN specific applications (e.g., LiDAR, 5G) will be explored at a later date. In addition to the market, supply and value chain analyses addressed in Section 1 of this report, a SWOT (Strength, Weakness, Opportunity, Threat) analysis and potential energy savings analysis was conducted for each application area to identify the major potential WBG application area(s) with a U.S. competitiveness opportunity in the future.« less

Tsunami evacuation modelling as a tool for risk reduction: application to the coastal area of El Salvador

NASA Astrophysics Data System (ADS)

González-Riancho, P.; Aguirre-Ayerbe, I.; Aniel-Quiroga, I.; Abad, S.; González, M.; Larreynaga, J.; Gavidia, F.; Gutiérrez, O. Q.; Álvarez-Gómez, J. A.; Medina, R.

2013-12-01

Advances in the understanding and prediction of tsunami impacts allow the development of risk reduction strategies for tsunami-prone areas. This paper presents an integral framework for the formulation of tsunami evacuation plans based on tsunami vulnerability assessment and evacuation modelling. This framework considers (i) the hazard aspects (tsunami flooding characteristics and arrival time), (ii) the characteristics of the exposed area (people, shelters and road network), (iii) the current tsunami warning procedures and timing, (iv) the time needed to evacuate the population, and (v) the identification of measures to improve the evacuation process. The proposed methodological framework aims to bridge between risk assessment and risk management in terms of tsunami evacuation, as it allows for an estimation of the degree of evacuation success of specific management options, as well as for the classification and prioritization of the gathered information, in order to formulate an optimal evacuation plan. The framework has been applied to the El Salvador case study, demonstrating its applicability to site-specific response times and population characteristics.

Future superconductivity applications in space - A review

NASA Astrophysics Data System (ADS)

Krishen, Kumar; Ignatiev, Alex

High temperature superconductor (HISC) materials and devices can provide immediate applications for many space missions. The in-space thermal environment provides an opportunity to develop, test, and apply this technology to enhance performance and reliability for many applications of crucial importance to NASA. Specifically, the technology development areas include: (1) high current power transmission, (2) microwave components, devices, and antennas, (3) microwave, optical, and infrared sensors, (4) signal processors, (5) submillimeter wave components and systems, (6) ultra stable space clocks, (7) electromagnetic launch systems, and (8) accelerometers and position sensors for flight operations. HTSC is expected to impact NASA's Lunar Bases, Mars exploration, Mission to Earth, and Planetary exploration programs providing enabling and cost-effect technology. A review of the space applications of the HTSC technology is presented. Problem areas in technology development needing special attention are identified.

Some issues related to simulation of the tracking and communications computer network

NASA Technical Reports Server (NTRS)

Lacovara, Robert C.

1989-01-01

The Communications Performance and Integration branch of the Tracking and Communications Division has an ongoing involvement in the simulation of its flight hardware for Space Station Freedom. Specifically, the communication process between central processor(s) and orbital replaceable units (ORU's) is simulated with varying degrees of fidelity. The results of investigations into three aspects of this simulation effort are given. The most general area involves the use of computer assisted software engineering (CASE) tools for this particular simulation. The second area of interest is simulation methods for systems of mixed hardware and software. The final area investigated is the application of simulation methods to one of the proposed computer network protocols for space station, specifically IEEE 802.4.

Some issues related to simulation of the tracking and communications computer network

NASA Astrophysics Data System (ADS)

Lacovara, Robert C.

1989-12-01

The Communications Performance and Integration branch of the Tracking and Communications Division has an ongoing involvement in the simulation of its flight hardware for Space Station Freedom. Specifically, the communication process between central processor(s) and orbital replaceable units (ORU's) is simulated with varying degrees of fidelity. The results of investigations into three aspects of this simulation effort are given. The most general area involves the use of computer assisted software engineering (CASE) tools for this particular simulation. The second area of interest is simulation methods for systems of mixed hardware and software. The final area investigated is the application of simulation methods to one of the proposed computer network protocols for space station, specifically IEEE 802.4.

Nanopatterned polymer brushes: conformation, fabrication and applications.

PubMed

Yu, Qian; Ista, Linnea K; Gu, Renpeng; Zauscher, Stefan; López, Gabriel P

2016-01-14

Surfaces with end-grafted, nanopatterned polymer brushes that exhibit well-defined feature dimensions and controlled chemical and physical properties provide versatile platforms not only for investigation of nanoscale phenomena at biointerfaces, but also for the development of advanced devices relevant to biotechnology and electronics applications. In this review, we first give a brief introduction of scaling behavior of nanopatterned polymer brushes and then summarize recent progress in fabrication and application of nanopatterned polymer brushes. Specifically, we highlight applications of nanopatterned stimuli-responsive polymer brushes in the areas of biomedicine and biotechnology.

Nanopatterned polymer brushes: conformation, fabrication and applications

NASA Astrophysics Data System (ADS)

Yu, Qian; Ista, Linnea K.; Gu, Renpeng; Zauscher, Stefan; López, Gabriel P.

2015-12-01

Surfaces with end-grafted, nanopatterned polymer brushes that exhibit well-defined feature dimensions and controlled chemical and physical properties provide versatile platforms not only for investigation of nanoscale phenomena at biointerfaces, but also for the development of advanced devices relevant to biotechnology and electronics applications. In this review, we first give a brief introduction of scaling behavior of nanopatterned polymer brushes and then summarize recent progress in fabrication and application of nanopatterned polymer brushes. Specifically, we highlight applications of nanopatterned stimuli-responsive polymer brushes in the areas of biomedicine and biotechnology.

Neutral buoyancy testing of architectural and environmental concepts of space vehicle design

NASA Technical Reports Server (NTRS)

Lenda, J. A.; Rosener, A. A.; Stephenson, M. L.

1972-01-01

Design guidelines are presented that are applicable to providing habitability areas and furniture elements for extended periods in a zero gravity environment. This was accomplished by: (1) analyzing the existing habitability crew area requirements, mobility and restraint aids, cross-cultural design, and establishing a man model for zero gravity; (2) designing specific furniture elements, chair and table, and volumes for a stateroom, office, bathroom, galley, and wardroom; and (3) neutral buoyancy testing and evaluation of these areas.

Interpretation of ERTS-MSS images of a Savanna area in eastern Colombia

NASA Technical Reports Server (NTRS)

Elberson, G. W. W.

1973-01-01

The application of ERTS-1 imagery for extrapolating existing soil maps into unmapped areas of the Llanos Orientales of Colombia, South America is discussed. Interpretations of ERTS-1 data were made according to conventional photointerpretation techniques. Most units delineated in the existing reconnaissance soil map at a scale of 1:250,000 could be recognized and delineated in the ERTS image. The methods of interpretation are described and the results obtained for specific areas are analyzed.

Shapes of embedded minimal surfaces

PubMed Central

Colding, Tobias H.; Minicozzi, William P.

2006-01-01

Surfaces that locally minimize area have been extensively used to model physical phenomena, including soap films, black holes, compound polymers, protein folding, etc. The mathematical field dates to the 1740s but has recently become an area of intense mathematical and scientific study, specifically in the areas of molecular engineering, materials science, and nanotechnology because of their many anticipated applications. In this work, we show that all minimal surfaces are built out of pieces of the surfaces in Figs. 1 and 2. PMID:16847265

Sensors, Volume 4, Thermal Sensors

NASA Astrophysics Data System (ADS)

Scholz, Jorg; Ricolfi, Teresio

1996-12-01

'Sensors' is the first self-contained series to deal with the whole area of sensors. It describes general aspects, technical and physical fundamentals, construction, function, applications and developments of the various types of sensors. This volume describes the construction and applicational aspects of thermal sensors while presenting a rigorous treatment of the underlying physical principles. It provides a unique overview of the various categories of sensors as well as of specific groups, e.g. temperature sensors (resistance thermometers, thermocouples, and radiation thermometers), noise and acoustic thermometers, heat-flow and mass-flow sensors. Specific facettes of applications are presented by specialists from different fields including process control, automotive technology and cryogenics. This volume is an indispensable reference work and text book for both specialists and newcomers, researchers and developers.

Cleanups in My Community

EPA Pesticide Factsheets

Cleanups in My Community (CIMC) is a public web application that enables integrated access through maps, lists and search filtering to site-specific information EPA has across all cleanup programs. CIMC taps into data publicly available from EPA's EnviroFacts (RCRA Corrective Action facilities, Brownfields properties and grant areas, Superfund NPL sites, other facility data) and web services (water monitoring stations, impaired waters, emergency responses, tribal boundaries, congressional districts, etc.) and connects to other applications (e.g., Superfund's CPAD) to provide easy seamless access to site-specific cleanup information with explanatory text and within the context of related data. Data can be filtered by cleanup program, geography, environmental indicators, controls, and cleanup stage. CIMC also provides some web services that integrate these data for others to use in their applications.

Measurement and testing of the acoustic properties of materials: a review

NASA Astrophysics Data System (ADS)

Zeqiri, Bajram; Scholl, Werner; Robinson, Stephen P.

2010-04-01

A review is presented of methods of measurement for a range of key acoustic properties of materials, spanning three application areas: airborne sound, underwater acoustics and ultrasound. The acoustic properties considered, primarily transmission loss (damping) and echo-reduction, are specifically important to the end application of any material. The state-of-the-art in measurement and likely future challenges are described in detail.

Field Testing of Geophysical Techniques.

DTIC Science & Technology

1981-11-01

influence drainage and groundwater movement in the surrounding area. Presumably, the direction of groundwater movement is to the north and out of the...applicable. Specifically, these additional techniques are: e Audio magneto- telluric (AMT) resistivity * Electromagnetics a Ground-probing radar Both

Load application for the contact mechanics analysis and wear prediction of total knee replacement.

PubMed

Zhang, Jing; Chen, Zhenxian; Wang, Ling; Li, Dichen; Jin, Zhongmin

2017-05-01

Tibiofemoral contact forces in total knee replacement have been measured at the medial and lateral sites respectively using an instrumented prosthesis, and predicted from musculoskeletal multibody dynamics models with a reasonable accuracy. However, it is uncommon that the medial and lateral forces are applied separately to replace a total axial load according to the ISO standard in the majority of current finite element analyses. In this study, we quantified the different effects of applying the medial and lateral loads separately versus the traditional total axial load application on contact mechanics and wear prediction of a patient-specific knee prosthesis. The load application position played an important role under the medial-lateral load application. The loading set which produced the closest load distribution to the multibody dynamics model was used to predict the contact mechanics and wear for the prosthesis and compared with the total axial load application. The medial-lateral load distribution using the present method was found to be closer to the multibody dynamics prediction than the traditional total axial load application, and the maximum contact pressure and contact area were consistent with the corresponding load variation. The predicted total volumetric wear rate and area were similar between the two load applications. However, the split of the predicted wear volumes on the medial and the lateral sides was different. The lateral volumetric wear rate was 31.46% smaller than the medial from the traditional load application prediction, while from the medial-lateral load application, the lateral side was only 11.8% smaller than the medial. The medial-lateral load application could provide a new and more accurate method of load application for patient-specific preclinical contact mechanics and wear prediction of knee implants.

MathBrowser: Web-Enabled Mathematical Software with Application to the Chemistry Curriculum, v 1.0

NASA Astrophysics Data System (ADS)

Goldsmith, Jack G.

1997-10-01

MathSoft: Cambridge, MA, 1996; free via ftp from www.mathsoft.com. The movement to provide computer-based applications in chemistry has come to focus on three main areas: software aimed at specific applications (drawing, simulation, data analysis, etc.), multimedia applications designed to assist in the presentation of conceptual information, and packages to be used in conjunction with a particular textbook at a specific point in the chemistry curriculum. The result is a situation where no single software package devoted to problem solving can be used across a large segment of the curriculum. Adoption of World Wide Web (WWW) technology by a manufacturer of mathematical software, however, has produced software that provides an attractive means of providing a problem-solving resource to students in courses from freshman through senior level.

Facile synthesis of ZnCo2O4/rGO nanocomposite for effective supercapacitor application

NASA Astrophysics Data System (ADS)

Mary, A. Juliet Christina; Bose, A. Chandra

2017-05-01

ZnCo2O4/rGO nanocompoite material gives the high specific capacitance value of 704.2 F/g at a current density of 0.75 A/g. rGO material provides the effective surface area for the composite which leads to better performance for supercapacitor application. Stability of ZnCo2O4/rGO nanocomposite was tested up to 400 cycles. ZnCo2O4/rGO nanocomposite is the suitable material for supercapacitor application.

H.R. 1757--High Performance Computing and High Speed Networking Applications Act of 1993. Hearings before the Subcommittee on Science of the Committee on Science, Space, and Technology. House of Representatives, One Hundred Third Congress, First Session (April 27, May 6, May 11, 1993).

ERIC Educational Resources Information Center

Congress of the U.S., Washington, DC. House Committee on Science, Space and Technology.

This document contains the transcript of three hearings on the High Speed Performance Computing and High Speed Networking Applications Act of 1993 (H.R. 1757). The hearings were designed to obtain specific suggestions for improvements to the legislation and alternative or additional application areas that should be pursued. Testimony and prepared…

ERTS-1 applications in hydrology and water resources

NASA Technical Reports Server (NTRS)

Salomonson, V. V.; Rango, A.

1973-01-01

After having been in orbit for less than one year, the Earth Resources Technology Satellite (ERTS-1) has shown that it provides very applicable data for more effective monitoring and management of surface water features over the globe. Mapping flooded areas, snowcover, and wetlands and surveying the size, type, and response of glaciers to climate are among the specific areas where ERTS-1 data were applied. In addition the data collection system has proven to be a reliable tool for gathering hydrologic data from remote regions. Turbidity variations in lakes and rivers were also observed and related to shoreline erosion, industrial plant effluent, and overall water quality.

Towards new uses of botulinum toxin as a novel therapeutic tool.

PubMed

Pickett, Andy; Perrow, Karen

2011-01-01

The uses of botulinum toxin in the fields of neurology, ophthalmology, urology, rehabilitation medicine and aesthetic applications have been revolutionary for the treatment of patients. This non-invasive therapeutic has continually been developed since first discovered in the 1970s as a new approach to what were previously surgical treatments. As these applications develop, so also the molecules are developing into tools with new therapeutic properties in specific clinical areas. This review examines how the botulinum toxin molecule is being adapted to new therapeutic uses and also how new areas of use for the existing molecules are being identified. Prospects for future developments are also considered.

Urban remote sensing applications: TIMS observations of the City of Scottsdale

NASA Technical Reports Server (NTRS)

Christensen, Philip R.; Melendrez, David E.; Anderson, Donald L.; Hamilton, Victoria E.; Wenrich, Melissa L.; Howard, Douglas

1995-01-01

A research program has been initiated between Arizona State University and the City of Scottsdale, Arizona to study the potential applications of TIMS (Thermal Infrared Multispectral Scanner) data for urban scene classification, desert environmental assessment, and change detection. This program is part of a long-term effort to integrate remote sensing observations into state and local planning activities to improve decision making and future planning. Specific test sites include a section of the downtown Scottsdale region that has been mapped in very high detail as part of a pilot program to develop an extensive GIS database. This area thus provides excellent time history of the evolution of the city infrastructure, such as the timing and composition of street repavement. A second area of study includes the McDowell intensive study by state and local agencies to assess potential sites for urban development as well as preservation. These activities are of particular relevance as the Phoenix metropolitan area undergoes major expansion into the surrounding desert areas. The objectives of this study in urban areas are aimed at determining potential applications of TIMS data for classifying and assessing land use and surface temperatures. Land use centers on surface impermeability studies for storm runoff assessment and pollution control. These studies focus on determining the areal abundance of urban vegetation and undeveloped soil. Highly experimental applications include assessment and monitoring of pavement condition. Temperature studies focus on determining swimming pool area and temperature for use in monitoring evaporating and urban water consumption. These activities are of particular relevance as the Phoenix metropolitan area undergoes major expansion into the surrounding desert area.

Video Discs: Magic Lamps for Educators?

ERIC Educational Resources Information Center

Braun,

1978-01-01

This article focuses on electro-optical videodisc systems because of their educational advantages over electromechanical systems and specifically on the Philips/MCA system. Areas emerging for videodisc educational application are identified as lenear video, programed instruction, and interactive use with the computer. (CMV)

Budget Anthropology: A Unit Sampler.

ERIC Educational Resources Information Center

Fraker, G. Alan

Creative and inexpensive teaching suggestions for high school anthropology courses are presented. They are chosen specifically for programs which cannot afford expensive curriculum materials. All activities demonstrate the application of universal anthropological principles to the American society. Seven areas which reflect the general functions…

Viking dynamics experience with application to future payload design

NASA Technical Reports Server (NTRS)

Barrett, S.; Rader, W. P.; Payne, K. R.

1978-01-01

Analytical and test techniques are discussed. Areas in which hindsight indicated erroneous, redundant, or unnecessarily severe design and test specifications are identified. Recommendations are made for improvements in the dynamic design and criteria philosophy, aimed at reducing costs for payloads.

FREQUENCY OF MOUTHING BEHAVIOR IN YOUNG CHILDREN

EPA Science Inventory

Young children may be more likely than adults to be exposed to pesticides following a residential application as a result of hand- and object-to-mouth contacts in contaminated areas. However, relatively few studies have specifically evaluated mouthing behavior in children less ...

Case Studies in CAL!

ERIC Educational Resources Information Center

Rogers, David F., Ed.; Smith, P. R., Ed.

1984-01-01

Ten papers focus on applications in specific curriculum areas, modelling and simulation, and computer managed learning. Projects described include voice support for the visually handicapped, distance education, and industrial training, as well as teaching applied mathematics, several facets of engineering, zoology, and, with videodisc, observation…

FREQUENCY OF MOUTHING BEHAVIOR IN YOUNG CHILDREN

EPA Science Inventory

Young children, as compared to adults, are more likely to be exposed after a pesticide application due to potential hand- and object-to-mouth contacts in contaminated areas. However, relatively few studies have specifically evaluated mouthing behavior in children <60 months of...

A Greedy Scanning Data Collection Strategy for Large-Scale Wireless Sensor Networks with a Mobile Sink.

PubMed

Zhu, Chuan; Zhang, Sai; Han, Guangjie; Jiang, Jinfang; Rodrigues, Joel J P C

2016-09-06

Mobile sink is widely used for data collection in wireless sensor networks. It can avoid 'hot spot' problems but energy consumption caused by multihop transmission is still inefficient in real-time application scenarios. In this paper, a greedy scanning data collection strategy (GSDCS) is proposed, and we focus on how to reduce routing energy consumption by shortening total length of routing paths. We propose that the mobile sink adjusts its trajectory dynamically according to the changes of network, instead of predetermined trajectory or random walk. Next, the mobile sink determines which area has more source nodes, then it moves toward this area. The benefit of GSDCS is that most source nodes are no longer needed to upload sensory data for long distances. Especially in event-driven application scenarios, when event area changes, the mobile sink could arrive at the new event area where most source nodes are located currently. Hence energy can be saved. Analytical and simulation results show that compared with existing work, our GSDCS has a better performance in specific application scenarios.

A Greedy Scanning Data Collection Strategy for Large-Scale Wireless Sensor Networks with a Mobile Sink

PubMed Central

Zhu, Chuan; Zhang, Sai; Han, Guangjie; Jiang, Jinfang; Rodrigues, Joel J. P. C.

2016-01-01

Mobile sink is widely used for data collection in wireless sensor networks. It can avoid ‘hot spot’ problems but energy consumption caused by multihop transmission is still inefficient in real-time application scenarios. In this paper, a greedy scanning data collection strategy (GSDCS) is proposed, and we focus on how to reduce routing energy consumption by shortening total length of routing paths. We propose that the mobile sink adjusts its trajectory dynamically according to the changes of network, instead of predetermined trajectory or random walk. Next, the mobile sink determines which area has more source nodes, then it moves toward this area. The benefit of GSDCS is that most source nodes are no longer needed to upload sensory data for long distances. Especially in event-driven application scenarios, when event area changes, the mobile sink could arrive at the new event area where most source nodes are located currently. Hence energy can be saved. Analytical and simulation results show that compared with existing work, our GSDCS has a better performance in specific application scenarios. PMID:27608022

Digital orthoimagery base specification V1.0

USGS Publications Warehouse

Rufe, Philip P.

2014-01-01

The resolution requirement for orthoimagery in support of the The National Map of the U.S. Geological Survey (USGS) is 1 meter. However, as the Office of Management and Budget A-16 designated Federal agency responsible for base orthoimagery, the USGS National Geospatial Program (NGP) has developed this base specification to include higher resolution orthoimagery. Many Federal, State, and local programs use high-resolution orthoimagery for various purposes including critical infrastructure management, vector data updates, land-use analysis, natural resource inventory, and extraction of data. The complex nature of large-area orthoimagery datasets, combined with the broad interest in orthoimagery, which is of consistent quality and spatial accuracy, requires high-resolution orthoimagery to meet or exceed the format and content outlined in this specification. The USGS intends to use this specification primarily to create consistency across all NGP funded and managed orthoimagery collections, in particular, collections in support of the National Digital Orthoimagery Program (NDOP). In the absence of other comprehensive specifications or standards, the USGS intends that this specification will, to the highest degree practical, be adopted by other USGS programs and mission areas, and by other Federal agencies. This base specification, defining minimum parameters for orthoimagery data collection. Local conditions in any given project area, specialized applications for the data, or the preferences of cooperators, may mandate more stringent requirements. The USGS fully supports the acquisition of more detailed, accurate, or value-added data that exceed the base specification outlined herein. A partial list of common “buy-up” options is provided in appendix 1 for those areas and projects that require more stringent or expanded specifications.

Small wastewater treatment plants in mountain areas: combination of septic tank and biological filter.

PubMed

Maunoir, S; Philip, H; Rambaud, A

2007-01-01

Research work has been carried out for more than 20 years by Eparco and the University of Montpellier (France) on the application of biological wastewater treatment processes for small communities. This research has led to a new process which is particularly suitable for remote populations, taking into account several specificities such as as the seasonal fluctuations in the population, the accessibility of the site, the absence of a power supply on site, the reduced area of land available and the low maintenance. Thus, the process, which combines a septic tank operating under anaerobic conditions and a biological aerobic filter, is a solution for wastewater treatment in mountain areas. This paper presents the process and three full-scale applications in the region of the Alps.

The NASA Applied Science Program Disasters Area: Disaster Applications Research and Response

NASA Astrophysics Data System (ADS)

Murray, J. J.; Lindsay, F. E.; Stough, T.; Jones, C. E.

2014-12-01

The goal of the Natural Disaster Application Area is to use NASA's capabilities in spaceborne, airborne, surface observations, higher-level derived data products, and modeling and data analysis to improve natural disaster forecasting, mitigation, and response. The Natural Disaster Application Area applies its remote sensing observations, modeling and analysis capabilities to provide hazard and disaster information where and when it is needed. Our application research activities specifically contribute to 1) Understanding the natural processes that produce hazards, 2)Developing hazard mitigation technologies, and 3)Recognizing vulnerability of interdependent critical infrastructure. The Natural Disasters Application area selects research projects through a rigorous, impartial peer-review process that address a broad spectrum of disasters which afflict populations within the United States, regionally and globally. Currently there are 19 active projects in the research portfolio which address the detection, characterization, forecasting and response to a broad range of natural disasters including earthquakes, tsunamis, volcanic eruptions and ash dispersion, wildfires, hurricanes, floods, tornado damage assessment, oil spills and disaster data mining. The Disasters team works with federal agencies to aid the government in meeting the challenges associated with natural disaster response and to transfer technologies to agencies as they become operational. Internationally, the Disasters Area also supports the Committee on Earth Observations Working Group on Disasters, and the International Charter on Space and Disasters to increase, strengthen, and coordinate contributions of NASA Earth-observing satellites and applications products to disaster risk management. The CEOS group will lead pilot efforts focused on identifying key systems to support flooding, earthquake, and volcanic events.

Adaptation of existing infrared technologies to unanticipated applications

NASA Astrophysics Data System (ADS)

Peng, Philip

2005-01-01

Radiation thermometry is just but one of many applications, both potential and realized, of infrared technology. During the SARS (Severe Acute Respiratory Syndromes) global crisis in 2003, the technology was utilized as a preliminary screening method for infected persons as a defense against a major outbreak, as the primary symptom of this disease is elevated body temperature. ATC timely developed a product designed specifically for mass volume crowd screening of febrile individuals. For this application, the machine must register temperature of subjects rapidly and efficiently, with a certain degree of accuracy, and function for extended periods of time. The equipment must be safe to use, easily deployed, and function with minimum maintenance needed. The ATIR-303 model satisfies all of the above and other pre-requisite conditions amicably. Studies on the correlation between the maximum temperature registered among individual's facial features, as measured under the conditions of usage, and the core temperature of individuals were performed. The results demonstrated that ATIR-303 is very suitable for this application. Other applications of the infrared technology in various areas, like medical diagnosis, non-destructive testing, security, search and rescue, and others, are also interest areas of ATC. The progress ATC has achieved in these areas is presented also.

Changes in optical properties of electroporated cells as revealed by digital holographic microscopy

PubMed Central

Calin, Violeta L.; Mihailescu, Mona; Mihale, Nicolae; Baluta, Alexandra V.; Kovacs, Eugenia; Savopol, Tudor; Moisescu, Mihaela G.

2017-01-01

Changes in optical and shape-related characteristics of B16F10 cells after electroporation were investigated using digital holographic microscopy (DHM). Bipolar rectangular pulses specific for electrochemotherapy were used. Electroporation was performed in an “off-axis” DHM set-up without using exogenous markers. Two types of cell parameters were monitored seconds and minutes after pulse train application: parameters addressing a specifically defined area of the cell (refractive index and cell height) and global cell parameters (projected area, optical phase shift profile and dry mass). The biphasic behavior of cellular parameters was explained by water and mannitol dynamics through the electropermeabilized cell membrane. PMID:28736667

A novel photovoltaic power system which uses a large area concentrator mirror

NASA Technical Reports Server (NTRS)

Arrison, Anne; Fatemi, Navid

1987-01-01

A preliminary analysis has been made of a novel photovoltaic power system concept. The system is composed of a small area, dense photovoltaic array, a large area solar concentrator, and a battery system for energy storage. The feasibility of such a system is assessed for space power applications. The orbital efficiency, specific power, mass, and area of the system are calculated under various conditions and compared with those for the organic Rankine cycle solar dynamic system proposed for Space Station. Near term and advanced large area concentrator photovoltaic systems not only compare favorably to solar dynamic systems in terms of performance but offer other benefits as well.

Predicting the impact of lava flows at Mount Etna by an innovative method based on Cellular Automata: Applications regarding land-use and civil defence planning

NASA Astrophysics Data System (ADS)

Crisci, G. M.; Avolio, M. V.; D'Ambrosio, D.; di Gregorio, S.; Lupiano, G. V.; Rongo, R.; Spataro, W.; Benhcke, B.; Neri, M.

2009-04-01

Forecasting the time, character and impact of future eruptions is difficult at volcanoes with complex eruptive behaviour, such as Mount Etna, where eruptions occur from the summit and on the flanks, affecting areas distant from each other. Modern efforts for hazard evaluation and contingency planning in volcanic areas draw heavily on hazard maps and numerical simulations. The computational model here applied belongs to the SCIARA family of lava flow simulation models. In the specific case this is the SCIARA-fv release, which is considered to give the most accurate and efficient performance, given the extent (567 km2) of the study area and the great number of simulations to be carried out. The model is based on the Cellular Automata computational paradigm and, specifically, on the Macroscopic Cellular Automata approach for the modelling of spatially extended dynamic systems2. This work addresses the problem of compiling high-detailed susceptibility maps with an elaborate approach in the numerical simulation of Etnean lava flows, based on the results of 39,300 simulations of flows erupted from a grid of 393 hypothetical vents in the eastern sector of Etna. This sector was chosen because it is densely populated and frequently affected by flank eruptions. Besides the definition of general susceptibility maps, the availability of a large number of lava flows of different eruption types, magnitudes and locations simulated for this study allows the instantaneous extraction of various scenarios on demand. For instance, in a Civil Defence oriented application, it is possible to identify all source areas of lava flows capable of affecting a given area of interest, such as a town or a major infrastructure. Indeed, this application is rapidly accomplished by querying the simulation database, by selecting the lava flows that affect the area of interest and by circumscribing their sources. Eventually, a specific category of simulation is dedicated to the assessment of protective measures, such as earth barriers, for mitigating lava invasion susceptibility in given areas. For the case if the town of Nicolosi, results show that the barrier would be necessary to effectively protect the town centre. The methodology here described can therefore represent a substantial advance in the field of lava flows impact prediction and can also have immediate, far-reaching implications both in land-use and civil defence planning.

Multi-anode wire two dimensional proportional counter for detecting Iron-55 X-Ray Radiation

NASA Astrophysics Data System (ADS)

Weston, Michael William James

Radiation detectors in many applications use small sensor areas or large tubes which only collect one-dimensional information. There are some applications that require analyzing a large area and locating specific elements such as contamination on the heat tiles of a space shuttle or features on historical artifacts. The process can be time consuming and scanning a large area in a single pass is beneficial. The use of a two dimensional multi-wire proportional counter provides a large detection window presenting positional information in a single pass. This thesis described the design and implementation of an experimental detector to evaluate a specific design intended for use as a handheld instrument. The main effort of this research was to custom build a detector for testing purposes. The aluminum chamber and all circuit boards were custom designed and built specifically for this application. Various software and programmable logic algorithms were designed to analyze the raw data in real time and attempted to determine what data was useful and what could be discarded. The research presented here provides results useful for designing an improved second generation detector in the future. With the anode wire spacing chosen and the minimal collimation of the radiation source, detected events occurred all over the detection grid at any time. The raw event data did not make determining the source position easy and further data correlation was required. An abundance of samples had multiple wire hits which were not useful because it falsely reported the source to be all over the place and at different energy levels. By narrowing down the results to only use the largest signal pairs on different axes in each event, a much more accurate analysis of where the source existed above the grid was determined. The basic principle and construction method was shown to work, however the gas selection, geometry and anode wire constructs proved to be poor. To provide a system optimized for a specific application would require detailed Monte Carlo simulations. These simulation results together with the details and techniques implemented in this thesis would provide a final instrument of much higher accuracy.

Plasma Sterilization Technology for Spacecraft Applications

NASA Technical Reports Server (NTRS)

Fraser, S. J.; Olson, R. L.; Leavens, W. M.

1975-01-01

The application of plasma gas technology to sterilization and decontamination of spacecraft components is considered. Areas investigated include: effective sterilizing ranges of four separate gases; lethal constituents of a plasma environment; effectiveness of plasma against a diverse group of microorganisms; penetrating efficiency of plasmas for sterilization; and compatibility of spacecraft materials with plasma environments. Results demonstrated that plasma gas, specifically helium plasma, is a highly effective sterilant and is compatible with spacecraft materials.

Neutron Shielding Effectiveness of Multifunctional Composite Materials

DTIC Science & Technology

2013-03-01

greater degree of flexibility in design and engineering of specialized space vehicle shielding applications compared to aluminum. A new design for...photon/electron transport. Specific areas of application include, but are not limited to, radiation protection and dosimetry, radiation shielding...of 37.8%. The reaction of interest is 64Zn(n,p)64Cu, where 64Cu has a half-life of 12.7 hours [5]. When this reaction occurs a positron

Multifunctional Nanoparticles as Biocompatible Targeted Probes for Human Cancer Diagnosis and Therapy

PubMed Central

Yong, Ken-Tye; Roy, Indrajit; Swihart, Mark T.; Prasad, Paras N.

2009-01-01

The use of nanoparticles in biological application has been rapidly advancing toward practical applications in human cancer diagnosis and therapy. Upon linking the nanoparticles with biomolecules, they can be used to locate cancerous area as well as for traceable drug delivery with high affinity and specificity. In this review, we discuss the engineering of multifunctional nanoparticle probes and their use in bioimaging and nanomedicine. PMID:20305738

MPEG-21 in broadcasting: the novel digital broadcast item model

NASA Astrophysics Data System (ADS)

Lugmayr, Artur R.; Touimi, Abdellatif B.; Kaneko, Itaru; Kim, Jong-Nam; Alberti, Claudio; Yona, Sadigurschi; Kim, Jaejoon; Andrade, Maria Teresa; Kalli, Seppo

2004-05-01

The MPEG experts are currently developing the MPEG-21 set of standards and this includes a framework and specifications for digital rights management (DRM), delivery of quality of services (QoS) over heterogeneous networks and terminals, packaging of multimedia content and other things essential for the infrastructural aspects of multimedia content distribution. Considerable research effort is being applied to these new developments and the capabilities of MPEG-21 technologies to address specific application areas are being investigated. One such application area is broadcasting, in particular the development of digital TV and its services. In more practical terms, digital TV addresses networking, events, channels, services, programs, signaling, encoding, bandwidth, conditional access, subscription, advertisements and interactivity. MPEG-21 provides an excellent framework of standards to be applied in digital TV applications. Within the scope of this research work we describe a new model based on MPEG-21 and its relevance to digital TV: the digital broadcast item model (DBIM). The goal of the DBIM is to elaborate the potential of MPEG-21 for digital TV applications. Within this paper we focus on a general description of the DBIM, quality of service (QoS) management and metadata filtering, digital rights management and also present use-cases and scenarios where the DBIM"s role is explored in detail.

The effect of music video exposure on students' perceived clinical applications of popular music in the field of music therapy: a pilot study.

PubMed

Gooding, Lori F; Mori-Inoue, Satoko

2011-01-01

The purpose of this study was to examine the effect of video exposure on music therapy students' perceptions of clinical applications of popular music in the field of music therapy. Fifty-one participants were randomly divided into two groups and exposed to a popular song in either audio-only or music video format. Participants were asked to indicate clinical applications; specifically, participants chose: (a) possible population(s), (b) most appropriate population(s), (c) possible age range(s), (d) most appropriate age ranges, (e) possible goal area(s) and (f) most appropriate goal area. Data for each of these categories were compiled and analyzed, with no significant differences found in the choices made by the audio-only and video groups. Three items, (a) selection of the bereavement population, (b) selection of bereavement as the most appropriate population and (c) selection of the age ranges of pre teen/mature adult, were additionally selected for further analysis due to their relationship to the video content. Analysis results revealed a significant difference between the video and audio-only groups for the selection of these specific items, with the video group's selections more closely aligned to the video content. Results of this pilot study suggest that music video exposure to popular music can impact how students choose to implement popular songs in the field of music therapy.

IMT-2000 Satellite Standards with Applications to Mobile Air Traffic Communications Networks

NASA Technical Reports Server (NTRS)

Shamma, Mohammed A.

2004-01-01

The International Mobile Telecommunications - 2000 (IMT-2000) standard and more specifically the Satellite component of it, is investigated as a potential alternative for communications to aircraft mobile users en-route and in terminal area. Its application to Air Traffic Management (ATM) communication needs is considered. A summary of the specifications of IMT-2000 satellite standards are outlined. It is shown via a system research analysis that it is possible to support most air traffic communication needs via an IMT-2000 infrastructure. This technology can compliment existing, or future digital aeronautical communications technologies such as VDL2, VDL3, Mode S, and UAT.

Porosity control in nanoporous carbide-derived carbon by oxidation in air and carbon dioxide

DOE Office of Scientific and Technical Information (OSTI.GOV)

Osswald, S.; Portet, C.; Gogotsi, Y., E-mail: gogotsi@drexel.ed

2009-07-15

Carbide-derived carbons (CDC) allow a precise control over the pore size through the selection of the carbide precursor and varying of the synthesis conditions. However, their pore volume is limited by the carbide stoichiometry. While activation of carbons derived from various organic precursors has been widely studied, this process may similarly be able to increase the pore volume and specific surface area of CDC. Oxidation of carbide-derived carbon in air and CO{sub 2} at different temperatures and times allows for significant increase in pore volume and specific surface area as well as control over average pore size with subnanometer accuracy.more » The effect of activation and associated changes in the pore volume and surface area on the hydrogen uptake are also discussed. - Graphical abstract: Carbide-derived carbons (CDC) provide great potential for sorption of toxicants and gas storage applications. Activation of CDC in air and CO{sub 2} at different temperatures and times is applied in order to maximize pore volume and specific surface area, and control the average pore size with subnanometer accuracy.« less

Laser assisted microdissection, an efficient technique to understand tissue specific gene expression patterns and functional genomics in plants.

PubMed

Gautam, Vibhav; Sarkar, Ananda K

2015-04-01

Laser assisted microdissection (LAM) is an advanced technology used to perform tissue or cell-specific expression profiling of genes and proteins, owing to its ability to isolate the desired tissue or cell type from a heterogeneous population. Due to the specificity and high efficiency acquired during its pioneering use in medical science, the LAM technique has quickly been adopted for use in many biological researches. Today, it has become a potent tool to address a wide range of questions in diverse field of plant biology. Beginning with comparative transcriptome analysis of different tissues such as reproductive parts, meristems, lateral organs, roots etc., LAM has also been extensively used in plant-pathogen interaction studies, proteomics, and metabolomics. In combination with next generation sequencing and proteomics analysis, LAM has opened up promising opportunities in the area of large scale functional studies in plants. Ever since the advent of this technique, significant improvements have been achieved in term of its instrumentation and method, which has made LAM a more efficient tool applicable in wider research areas. Here, we discuss the advancement of LAM technique with special emphasis on its methodology and highlight its scope in modern research areas of plant biology. Although we put emphasis on use of LAM in transcriptome studies, which is mostly used, we also discuss its recent application and scope in proteome and metabolome studies.

Economic study of low temperature geothermal energy in Lassen and Modoc counties, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1977-04-01

The purpose of this study was to investigate the feasibility of using low cost, low temperature geothermal energy in job-producing industries to increase employment and encourage economic development. The study, encompassing all of Lassen and modoc Counties, was to be site-specific, referencing candidate geothermal applications to known hot wells and springs as previously determined, or to new wells with specific characteristics as defined in the Scope of Work. The emphasis was to be placed on economically practical and readily achievable applications from known resources, thus complimenting the recently completed ERDA-Susanville Study where a designated community was used as a ''laboratory''more » in which land-use planning, institutional aspects, geological assessments, technical modeling and socioeconomic impacts were all examined in overview. During the course of the study, monthly progress reports were prepared and reviewed with the Commission so that emphasis on particular features of study could be changed as necessary to reflect updated findings and to redirect efforts into additional areas of potential promise as they became apparent. In this manner, a degree of flexibility was maintained which allowed a more comprehensive study than would have been otherwise possible. Although the report generates both positive and negative findings in specific areas of investigation, it is felt that the overall long term prognosis for geothermal energy stimulus to industry in the area is excellent.« less

Roadmap for In-Space Propulsion Technology

NASA Technical Reports Server (NTRS)

Meyer, Michael; Johnson, Les; Palaszewski, Bryan; Coote, David; Goebel, Dan; White, Harold

2012-01-01

NASA has created a roadmap for the development of advanced in-space propulsion technologies for the NASA Office of the Chief Technologist (OCT). This roadmap was drafted by a team of subject matter experts from within the Agency and then independently evaluated, integrated and prioritized by a National Research Council (NRC) panel. The roadmap describes a portfolio of in-space propulsion technologies that could meet future space science and exploration needs, and shows their traceability to potential future missions. Mission applications range from small satellites and robotic deep space exploration to space stations and human missions to Mars. Development of technologies within the area of in-space propulsion will result in technical solutions with improvements in thrust, specific impulse (Isp), power, specific mass (or specific power), volume, system mass, system complexity, operational complexity, commonality with other spacecraft systems, manufacturability, durability, and of course, cost. These types of improvements will yield decreased transit times, increased payload mass, safer spacecraft, and decreased costs. In some instances, development of technologies within this area will result in mission-enabling breakthroughs that will revolutionize space exploration. There is no single propulsion technology that will benefit all missions or mission types. The requirements for in-space propulsion vary widely according to their intended application. This paper provides an updated summary of the In-Space Propulsion Systems technology area roadmap incorporating the recommendations of the NRC.

Hysteresis losses and specific absorption rate measurements in magnetic nanoparticles for hyperthermia applications.

PubMed

Coïsson, Marco; Barrera, Gabriele; Celegato, Federica; Martino, Luca; Kane, Shashank N; Raghuvanshi, Saroj; Vinai, Franco; Tiberto, Paola

2017-06-01

Magnetic hysteresis loops areas and hyperthermia on magnetic nanoparticles have been studied with the aim of providing reliable and reproducible methods of measuring the specific absorption rate (SAR). The SAR of Fe 3 O 4 nanoparticles with two different mean sizes, and Ni 1-x Zn x Fe 2 O 4 ferrites with 0 ≤ x ≤ 0.8 has been measured with three approaches: static hysteresis loops areas, dynamic hysteresis loops areas and hyperthermia of a water solution. For dynamic loops and thermometric measurements, specific experimental setups have been developed, that operate at comparable frequencies (≈ 69kHz and ≈ 100kHz respectively) and rf magnetic field peak values (up to 100mT). The hyperthermia setup has been fully modelled to provide a direct measurement of the SAR of the magnetic nanoparticles by taking into account the heat exchange with the surrounding environment in non-adiabatic conditions and the parasitic heating of the water due to ionic currents. Dynamic hysteresis loops are shown to provide an accurate determination of the SAR except for superparamagnetic samples, where the boundary with a blocked regime could be crossed in dynamic conditions. Static hysteresis loops consistently underestimate the specific absorption rate but can be used to select the most promising samples. A means of reliably measure SAR of magnetic nanoparticles by different approaches for hyperthermia applications is presented and its validity discussed by comparing different methods. This work fits within the general subject of metrological traceability in medicine with a specific focus on magnetic hyperthermia. This article is part of a Special Issue entitled "Recent Advances in Bionanomaterials" Guest Editor: Dr. Marie-Louise Saboungi and Dr. Samuel D. Bader. Copyright © 2016 Elsevier B.V. All rights reserved.

Aloe vera Derived Activated High-Surface-Area Carbon for Flexible and High-Energy Supercapacitors.

PubMed

Karnan, M; Subramani, K; Sudhan, N; Ilayaraja, N; Sathish, M

2016-12-28

Materials which possess high specific capacitance in device configuration with low cost are essential for viable application in supercapacitors. Herein, a flexible high-energy supercapacitor device was fabricated using porous activated high-surface-area carbon derived from aloe leaf (Aloe vera) as a precursor. The A. vera derived activated carbon showed mesoporous nature with high specific surface area of ∼1890 m 2 /g. A high specific capacitance of 410 and 306 F/g was achieved in three-electrode and symmetric two-electrode system configurations in aqueous electrolyte, respectively. The fabricated all-solid-state device showed a high specific capacitance of 244 F/g with an energy density of 8.6 Wh/kg. In an ionic liquid electrolyte, the fabricated device showed a high specific capacitance of 126 F/g and a wide potential window up to 3 V, which results in a high energy density of 40 Wh/kg. Furthermore, it was observed that the activation temperature has significant role in the electrochemical performance, as the activated sample at 700 °C showed best activity than the samples activated at 600 and 800 °C. The electron microscopic images (FE-SEM and HR-TEM) confirmed the formation of pores by the chemical activation. A fabricated supercapacitor device in ionic liquid with 3 V could power up a red LED for 30 min upon charging for 20s. Also, it is shown that the operation voltage and capacitance of flexible all-solid-state symmetric supercapacitors fabricated using aloe-derived activated carbon could be easily tuned by series and parallel combinations. The performance of fabricated supercapacitor devices using A. vera derived activated carbon in all-solid-state and ionic liquid indicates their viable applications in flexible devices and energy storage.

Survey of Nickel-Aluminium-Bronze Casting Alloys on Marine Applications,

DTIC Science & Technology

1981-04-01

and corrosion performance of nickel-aluminium bronze (NAB)/covered by naval specification DGS-8520 and DGS-348 have been investigated. No evidence was...found to suggest that there would be any significant difference in corrosion performance between alloys meeting the two specifications. Early... corrosion problems associated with the weld repair areas of castings have been overcome largely by using improved foundry and welding techniques followed by a

50 CFR 32.34 - Iowa.

Code of Federal Regulations, 2012 CFR

2012-10-01

... order with applicable refuge-specific regulations. De Soto National Wildlife Refuge A. Migratory Game Bird Hunting. [Reserved] B. Upland Game Hunting. We allow youth hunting of ring-necked pheasant on... manager will annually determine and publish hunting seasons, dates, and designated areas. C. Big Game...

50 CFR 32.34 - Iowa.

Code of Federal Regulations, 2013 CFR

2013-10-01

... order with applicable refuge-specific regulations. De Soto National Wildlife Refuge A. Migratory Game Bird Hunting. [Reserved] B. Upland Game Hunting. We allow youth hunting of ring-necked pheasant on... manager will annually determine and publish hunting seasons, dates, and designated areas. C. Big Game...

Workshop on The Rio Grande Rift: Crustal Modeling and Applications of Remote Sensing

NASA Technical Reports Server (NTRS)

Blanchard, D. P. (Editor)

1980-01-01

The elements of a program that could address significant earth science problems by combining remote sensing and traditional geological, geophysical, and geochemical approaches were addressed. Specific areas and tasks related to the Rio Grande Rift are discussed.

The organism is the product.

PubMed

Kelly, Jason

2012-01-20

A new industry model is emerging where microbes are first developed by specialist organism engineering firms and then deployed by customers in specific application areas. It is now realistic for companies without prior fermentation experience to purchase and deploy an engineered organism to expand their business.

7 CFR 457.8 - The application and policy.

Code of Federal Regulations, 2010 CFR

2010-01-01

... insurable. Agricultural experts. Persons who are employed by the Cooperative State Research, Education and... research or occupation is related to the specific crop or practice for which such expertise is sought... organizations: Appropriate Technology Transfer for Rural Areas, Sustainable Agriculture Research and Education...

COMPOUND-SPECIFIC STABLE ISOTOPE ANALYSIS TO DEMONSTRATE IN-SITU MTBE BIOTRANSFORMATION

EPA Science Inventory

Change of stable isotope composition of organic contaminants (isotopic fractionation) is a useful indicator of biotransformation. Most of applications to date are in the area of chlorinated solvents and recently BTEX, MTBE and TBA. Chemical reactions (biotic- and abiotic transfor...

Current capabilities and future directions in computational fluid dynamics

NASA Technical Reports Server (NTRS)

1986-01-01

A summary of significant findings is given, followed by specific recommendations for future directions of emphasis for computational fluid dynamics development. The discussion is organized into three application areas: external aerodynamics, hypersonics, and propulsion - and followed by a turbulence modeling synopsis.

Space Qualification Test of a-Silicon Solar Cell Modules

NASA Technical Reports Server (NTRS)

Kim, Q.; Lawton, R. A.; Manion, S. J.; Okuno, J. O.; Ruiz, R. P.; Vu, D. T.; Vu, D. T.; Kayali, S. A.; Jeffrey, F. R.

2004-01-01

The basic requirements of solar cell modules for space applications are generally described in MIL-S-83576 for the specific needs of the USAF. However, the specifications of solar cells intended for use on space terrestrial applications are not well defined. Therefore, this qualifications test effort was concentrated on critical areas specific to the microseismometer probe which is intended to be included in the Mars microprobe programs. Parameters that were evaluated included performance dependence on: illuminating angles, terrestrial temperatures, lifetime, as well as impact landing conditions. Our qualification efforts were limited to these most critical areas of concern. Most of the tested solar cell modules have met the requirements of the program except the impact tests. Surprisingly, one of the two single PIN 2 x 1 amorphous solar cell modules continued to function even after the 80000G impact tests. The output power parameters, Pout, FF, Isc and Voc, of the single PIN amorphous solar cell module were found to be 3.14 mW, 0.40, 9.98 mA and 0.78 V, respectively. These parameters are good enough to consider the solar module as a possible power source for the microprobe seismometer. Some recommendations were made to improve the usefulness of the amorphous silicon solar cell modules in space terrestrial applications, based on the results obtained from the intensive short term lab test effort.

Wind energy applications guide

DOE Office of Scientific and Technical Information (OSTI.GOV)

anon.

2001-01-01

The brochure is an introduction to various wind power applications for locations with underdeveloped transmission systems, from remote water pumping to village electrification. It includes an introductory section on wind energy, including wind power basics and system components and then provides examples of applications, including water pumping, stand-alone systems for home and business, systems for community centers, schools, and health clinics, and examples in the industrial area. There is also a page of contacts, plus two specific example applications for a wind-diesel system for a remote station in Antarctica and one on wind-diesel village electrification in Russia.

Applications of Telemedicine and Telecommunications to Disaster Medicine

PubMed Central

Garshnek, Victoria; Burkle, Frederick M.

1999-01-01

Disaster management utilizes diverse technologies to accomplish a complex set of tasks. Despite a decade of experience, few published reports have reviewed application of telemedicine (clinical care at a distance enabled by telecommunication) in disaster situations. Appropriate new telemedicine applications can improve future disaster medicine outcomes, based on lessons learned from a decade of civilian and military disaster (wide-area) telemedicine deployments. This manuscript reviews the history of telemedicine activities in actual disasters and similar scenarios as well as ongoing telemedicine innovations that may be applicable to disaster situations. Emergency care providers must begin to plan effectively to utilize disaster-specific telemedicine applications to improve future outcomes. PMID:9925226

Space Applications of Automation, Robotics and Machine Intelligence Systems (ARAMIS). Volume 1: Executive Summary

NASA Technical Reports Server (NTRS)

Miller, R. H.; Minsky, M. L.; Smith, D. B. S.

1982-01-01

Potential applications of automation, robotics, and machine intelligence systems (ARAMIS) to space activities, and to their related ground support functions are explored. The specific tasks which will be required by future space projects are identified. ARAMIS options which are candidates for those space project tasks and the relative merits of these options are defined and evaluated. Promising applications of ARAMIS and specific areas for further research are identified. The ARAMIS options defined and researched by the study group span the range from fully human to fully machine, including a number of intermediate options (e.g., humans assisted by computers, and various levels of teleoperation). By including this spectrum, the study searches for the optimum mix of humans and machines for space project tasks.

Lipids: From Chemical Structures, Biosynthesis, and Analyses to Industrial Applications.

PubMed

Li-Beisson, Yonghua; Nakamura, Yuki; Harwood, John

2016-01-01

Lipids are one of the major subcellular components, and play numerous essential functions. As well as their physiological roles, oils stored in biomass are useful commodities for a variety of biotechnological applications including food, chemical feedstocks, and fuel. Due to their agronomic as well as economic and societal importance, lipids have historically been subjected to intensive studies. Major current efforts are to increase the energy density of cell biomass, and/or create designer oils suitable for specific applications. This chapter covers some basic aspects of what one needs to know about lipids: definition, structure, function, metabolism and focus is also given on the development of modern lipid analytical tools and major current engineering approaches for biotechnological applications. This introductory chapter is intended to serve as a primer for all subsequent chapters in this book outlining current development in specific areas of lipids and their metabolism.

An AdaBoost Based Approach to Automatic Classification and Detection of Buildings Footprints, Vegetation Areas and Roads from Satellite Images

NASA Astrophysics Data System (ADS)

Gonulalan, Cansu

In recent years, there has been an increasing demand for applications to monitor the targets related to land-use, using remote sensing images. Advances in remote sensing satellites give rise to the research in this area. Many applications ranging from urban growth planning to homeland security have already used the algorithms for automated object recognition from remote sensing imagery. However, they have still problems such as low accuracy on detection of targets, specific algorithms for a specific area etc. In this thesis, we focus on an automatic approach to classify and detect building foot-prints, road networks and vegetation areas. The automatic interpretation of visual data is a comprehensive task in computer vision field. The machine learning approaches improve the capability of classification in an intelligent way. We propose a method, which has high accuracy on detection and classification. The multi class classification is developed for detecting multiple objects. We present an AdaBoost-based approach along with the supervised learning algorithm. The combi- nation of AdaBoost with "Attentional Cascade" is adopted from Viola and Jones [1]. This combination decreases the computation time and gives opportunity to real time applications. For the feature extraction step, our contribution is to combine Haar-like features that include corner, rectangle and Gabor. Among all features, AdaBoost selects only critical features and generates in extremely efficient cascade structured classifier. Finally, we present and evaluate our experimental results. The overall system is tested and high performance of detection is achieved. The precision rate of the final multi-class classifier is over 98%.

Polymeric Micelles as Novel Carriers for Poorly Soluble Drugs--A Review.

PubMed

Reddy, B Pavan Kumar; Yadav, Hemant K S; Nagesha, Dattatri K; Raizaday, Abhay; Karim, Abdul

2015-06-01

Polymeric micelles are used as 'smart drug carriers' for targeting certain areas of the body by making them stimuli-sensitive or by attachment of a specific ligand molecule onto their surface. The main aim of using polymeric micelles is to deliver the poorly water soluble drugs. Now-a-days they are used especially in the areas of cancer therapy also. In this article we have reviewed several aspects of polymeric micelles concerning their mechanism of formation, chemical nature, preparation and characterization techniques, and their applications in the areas of drug delivery.

A case study in technology utilization: Fracture mechanics

NASA Technical Reports Server (NTRS)

1972-01-01

This review of NASA contributions to the technology of fracture mechanics illustrates a fundamental role of the Space Agency in a single technical area. While primarily pursuing its goal of minimizing the weight of flight hardware, NASA engineers have generated innovations having broad impact in nonaerospace communities. A review is given of how these specific NASA innovations are communicated to the technical community outside the Space Agency, and current application areas are outlined.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Collett, Raymond; Howland, James; Venkiteswaran, Prasad

This report examines the benefits of Parker Hannifin hydraulic hybrid brake energy recovery systems used in commercial applications for vocational purposes. A detailed background on the problem statement being addressed as well as the solution set specific for parcel delivery will be provided. Objectives of the demonstration performed in high start & stop applications included opportunities in fuel usage reduction, emissions reduction, vehicle productivity, and vehicle maintenance. Completed findings during the demonstration period and parallel investigations with NREL, CALSTART, along with a literature review will be provided herein on this research area. Lastly, results identified in the study by thirdmore » parties validated the savings potential in fuel reduction of on average of 19% to 52% over the baseline in terms of mpg (Lammert, 2014, p11), Parker data for parcel delivery vehicles in the field parallels this at a range of 35% - 50%, emissions reduction of 17.4% lower CO2 per mile and 30.4% lower NOx per mile (Gallo, 2014, p15), with maintenance improvement in the areas of brake and starter replacement, while leaving room for further study in the area of productivity in terms of specific metrics that can be applied and studied.« less

The application of phase contrast X-ray techniques for imaging Li-ion battery electrodes

NASA Astrophysics Data System (ADS)

Eastwood, D. S.; Bradley, R. S.; Tariq, F.; Cooper, S. J.; Taiwo, O. O.; Gelb, J.; Merkle, A.; Brett, D. J. L.; Brandon, N. P.; Withers, P. J.; Lee, P. D.; Shearing, P. R.

2014-04-01

In order to accelerate the commercialization of fuel cells and batteries across a range of applications, an understanding of the mechanisms by which they age and degrade at the microstructural level is required. Here, the most widely commercialized Li-ion batteries based on porous graphite based electrodes which de/intercalate Li+ ions during charge/discharge are studied by two phase contrast enhanced X-ray imaging modes, namely in-line phase contrast and Zernike phase contrast at the micro (synchrotron) and nano (laboratory X-ray microscope) level, respectively. The rate of charge cycling is directly dependent on the nature of the electrode microstructure, which are typically complex multi-scale 3D geometries with significant microstructural heterogeneities. We have been able to characterise the porosity and the tortuosity by micro-CT as well as the morphology of 5 individual graphite particles by nano-tomography finding that while their volume varied significantly their sphericity was surprisingly similar. The volume specific surface areas of the individual grains measured by nano-CT are significantly larger than the total volume specific surface area of the electrode from the micro-CT imaging, which can be attributed to the greater particle surface area visible at higher resolution.

7 CFR 3402.3 - Institutional eligibility.

Code of Federal Regulations, 2012 CFR

2012-01-01

... colleges and universities, by colleges and universities having significant minority enrollments and a... universities having a demonstrable capacity to carry out the teaching of food and agricultural sciences. All... specific subject area for which a grant application is made. It is the objective to award grants to...

7 CFR 3402.3 - Institutional eligibility.

Code of Federal Regulations, 2014 CFR

2014-01-01

... colleges and universities, by colleges and universities having significant minority enrollments and a... universities having a demonstrable capacity to carry out the teaching of food and agricultural sciences. All... specific subject area for which a grant application is made. It is the objective to award grants to...

7 CFR 3402.3 - Institutional eligibility.

Code of Federal Regulations, 2013 CFR

2013-01-01

... colleges and universities, by colleges and universities having significant minority enrollments and a... universities having a demonstrable capacity to carry out the teaching of food and agricultural sciences. All... specific subject area for which a grant application is made. It is the objective to award grants to...

24 CFR 888.202 - Manner of publication.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 202 SUPPORTIVE HOUSING FOR THE ELDERLY PROGRAM AND SECTION 811 SUPPORTIVE HOUSING FOR PERSONS WITH DISABILITIES PROGRAM) SECTION 8 HOUSING ASSISTANCE PAYMENTS PROGRAM-FAIR MARKET RENTS AND CONTRACT RENT ANNUAL... published as market conditions indicate. In the case of revised factors applicable only to specific areas...

Vocation Units. Career Development Project.

ERIC Educational Resources Information Center

Moses, Elizabeth

The units contain suggestions for various approaches to the study of specific careers and career clusters at the junior high school level, and provide 13 lessons covering the areas of: obtaining career information, creative writing, journalism, health, environmental control, personal services and government, job application techniques, writing…

Supercapacitors based on pillared graphene nanostructures.

PubMed

Lin, Jian; Zhong, Jiebin; Bao, Duoduo; Reiber-Kyle, Jennifer; Wang, Wei; Vullev, Valentine; Ozkan, Mihrimah; Ozkan, Cengiz S

2012-03-01

We describe the fabrication of highly conductive and large-area three dimensional pillared graphene nanostructure (PGN) films from assembly of vertically aligned CNT pillars on flexible copper foils for applications in electric double layer capacitors (EDLC). The PGN films synthesized via a one-step chemical vapor deposition process on flexible copper foils exhibit high conductivity with sheet resistance as low as 1.6 ohms per square and possessing high mechanical flexibility. Raman spectroscopy indicates the presence of multi walled carbon nanotubes (MWCNT) and their morphology can be controlled by the growth conditions. It was discovered that nitric acid treatment can significantly increase the specific capacitance of the devices. EDLC devices based on PGN electrodes (surface area of 565 m2/g) demonstrate enhanced performance with specific capacitance value as high as 330 F/g extracted from the current density-voltage (CV) measurements and energy density value of 45.8 Wh/kg. The hybrid graphene-CNT nanostructures are attractive for applications including supercapacitors, fuel cells and batteries.

STEREO Space Weather and the Space Weather Beacon

NASA Technical Reports Server (NTRS)

Biesecker, D. A.; Webb, D F.; SaintCyr, O. C.

2007-01-01

The Solar Terrestrial Relations Observatory (STEREO) is first and foremost a solar and interplanetary research mission, with one of the natural applications being in the area of space weather. The obvious potential for space weather applications is so great that NOAA has worked to incorporate the real-time data into their forecast center as much as possible. A subset of the STEREO data will be continuously downlinked in a real-time broadcast mode, called the Space Weather Beacon. Within the research community there has been considerable interest in conducting space weather related research with STEREO. Some of this research is geared towards making an immediate impact while other work is still very much in the research domain. There are many areas where STEREO might contribute and we cannot predict where all the successes will come. Here we discuss how STEREO will contribute to space weather and many of the specific research projects proposed to address STEREO space weather issues. We also discuss some specific uses of the STEREO data in the NOAA Space Environment Center.

Developing a quality assurance program for online services.

PubMed Central

Humphries, A W; Naisawald, G V

1991-01-01

A quality assurance (QA) program provides not only a mechanism for establishing training and competency standards, but also a method for continuously monitoring current service practices to correct shortcomings. The typical QA cycle includes these basic steps: select subject for review, establish measurable standards, evaluate existing services using the standards, identify problems, implement solutions, and reevaluate services. The Claude Moore Health Sciences Library (CMHSL) developed a quality assurance program for online services designed to evaluate services against specific criteria identified by research studies as being important to customer satisfaction. These criteria include reliability, responsiveness, approachability, communication, and physical factors. The application of these criteria to the library's existing online services in the quality review process is discussed with specific examples of the problems identified in each service area, as well as the solutions implemented to correct deficiencies. The application of the QA cycle to an online services program serves as a model of possible interventions. The use of QA principles to enhance online service quality can be extended to other library service areas. PMID:1909197

Developing a quality assurance program for online services.

PubMed

Humphries, A W; Naisawald, G V

1991-07-01

A quality assurance (QA) program provides not only a mechanism for establishing training and competency standards, but also a method for continuously monitoring current service practices to correct shortcomings. The typical QA cycle includes these basic steps: select subject for review, establish measurable standards, evaluate existing services using the standards, identify problems, implement solutions, and reevaluate services. The Claude Moore Health Sciences Library (CMHSL) developed a quality assurance program for online services designed to evaluate services against specific criteria identified by research studies as being important to customer satisfaction. These criteria include reliability, responsiveness, approachability, communication, and physical factors. The application of these criteria to the library's existing online services in the quality review process is discussed with specific examples of the problems identified in each service area, as well as the solutions implemented to correct deficiencies. The application of the QA cycle to an online services program serves as a model of possible interventions. The use of QA principles to enhance online service quality can be extended to other library service areas.

Structuring Broadcast Audio for Information Access

NASA Astrophysics Data System (ADS)

Gauvain, Jean-Luc; Lamel, Lori

2003-12-01

One rapidly expanding application area for state-of-the-art speech recognition technology is the automatic processing of broadcast audiovisual data for information access. Since much of the linguistic information is found in the audio channel, speech recognition is a key enabling technology which, when combined with information retrieval techniques, can be used for searching large audiovisual document collections. Audio indexing must take into account the specificities of audio data such as needing to deal with the continuous data stream and an imperfect word transcription. Other important considerations are dealing with language specificities and facilitating language portability. At Laboratoire d'Informatique pour la Mécanique et les Sciences de l'Ingénieur (LIMSI), broadcast news transcription systems have been developed for seven languages: English, French, German, Mandarin, Portuguese, Spanish, and Arabic. The transcription systems have been integrated into prototype demonstrators for several application areas such as audio data mining, structuring audiovisual archives, selective dissemination of information, and topic tracking for media monitoring. As examples, this paper addresses the spoken document retrieval and topic tracking tasks.

Design Approach and Implementation of Application Specific Instruction Set Processor for SHA-3 BLAKE Algorithm

NASA Astrophysics Data System (ADS)

Zhang, Yuli; Han, Jun; Weng, Xinqian; He, Zhongzhu; Zeng, Xiaoyang

This paper presents an Application Specific Instruction-set Processor (ASIP) for the SHA-3 BLAKE algorithm family by instruction set extensions (ISE) from an RISC (reduced instruction set computer) processor. With a design space exploration for this ASIP to increase the performance and reduce the area cost, we accomplish an efficient hardware and software implementation of BLAKE algorithm. The special instructions and their well-matched hardware function unit improve the calculation of the key section of the algorithm, namely G-functions. Also, relaxing the time constraint of the special function unit can decrease its hardware cost, while keeping the high data throughput of the processor. Evaluation results reveal the ASIP achieves 335Mbps and 176Mbps for BLAKE-256 and BLAKE-512. The extra area cost is only 8.06k equivalent gates. The proposed ASIP outperforms several software approaches on various platforms in cycle per byte. In fact, both high throughput and low hardware cost achieved by this programmable processor are comparable to that of ASIC implementations.

Metal-organic frameworks as biosensors for luminescence-based detection and imaging

PubMed Central

Miller, Sophie E.; Teplensky, Michelle H.; Moghadam, Peyman Z.; Fairen-Jimenez, David

2016-01-01

Metal-organic frameworks (MOFs), formed by the self-assembly of metal centres or clusters and organic linkers, possess many key structural and chemical features that have enabled them to be used in sensing platforms for a variety of environmentally, chemically and biomedically relevant compounds. In particular, their high porosity, large surface area, tuneable chemical composition, high degree of crystallinity, and potential for post-synthetic modification for molecular recognition make MOFs promising candidates for biosensing applications. In this review, we separate our discussion of MOF biosensors into two categories: quantitative sensing, focusing specifically on luminescence-based sensors for the direct measurement of a specific analyte, and qualitative sensing, where we describe MOFs used for fluorescence microscopy and as magnetic resonance imaging contrast agents. We highlight several key publications in each of these areas, concluding that MOFs present an exciting, versatile new platform for biosensing applications and imaging, and we expect to see their usage grow as the field progresses. PMID:27499847

Space processing applications payload equipment study. Volume 2A: Experiment requirements

NASA Technical Reports Server (NTRS)

Smith, A. G.; Anderson, W. T., Jr.

1974-01-01

An analysis of the space processing applications payload equipment was conducted. The primary objective was to perform a review and an update of the space processing activity research equipment requirements and specifications that were derived in the first study. The analysis is based on the six major experimental classes of: (1) biological applications, (2) chemical processes in fluids, (3) crystal growth, (4) glass technology, (5) metallurgical processes, and (6) physical processes in fluids. Tables of data are prepared to show the functional requirements for the areas of investigation.

Community Relations Plan: Galena Airport and Campion Air Force Station, Alaska

DTIC Science & Technology

1994-11-11

toxic 0k Corporations that are not wastes at any facility listed or proposed for incorporated for the specific listing on the NPL and where site work ... working toward for awarding a TAG, and how to obtain incorporation under state laws. additional information are described. The Applications are...for similar work in the area. Notification Procedures and In special cases, where an applicant Evaluation Criteria group intends to apply for a single

Ada programming guidelines for deterministic storage management

NASA Technical Reports Server (NTRS)

Auty, David

1988-01-01

Previous reports have established that a program can be written in the Ada language such that the program's storage management requirements are determinable prior to its execution. Specific guidelines for ensuring such deterministic usage of Ada dynamic storage requirements are described. Because requirements may vary from one application to another, guidelines are presented in a most-restrictive to least-restrictive fashion to allow the reader to match appropriate restrictions to the particular application area under investigation.

Great Lakes Regional Phase 3 Commercialization Conference, Held in Detroit, Michigan on May 23 - 25, 1994

DTIC Science & Technology

1994-05-25

small highly efficient power systems to provide electricity for space applications. These converters are solar heated for near earth orbit applications...processing in NASA’s Wake Shield Facility. AMPS plans to complete product development in each of these specific technology areas utilizing SBIR...Corrosion: Crevice corrosion is a form of localized corrosion that occurs within crevices or shielded surfaces where stagnant solution is present

A preliminary study of the application of HCMM satellite data to define initial and boundary conditions for numerical models: A case study in St. Louis, Missouri

NASA Technical Reports Server (NTRS)

Vukovich, F. M. (Principal Investigator)

1982-01-01

Infrared and visible HCMM data were used to examine the potential application of these data to define initial and boundary conditions for mesoscale numerical models. Various boundary layer models were used to calculate the distribution of the surface heat flux, specific humidity depression (the difference between the specific humidity in the air at approxmately the 10 m level and the specific humidity at the ground), and the eddy vicosity in a 72 km by 72 km area centered about St. Louis, Missouri. Various aspects of the implications of the results on the meteorology of St. Louis are discussed. Overall, the results indicated that a reasonable estimate of the surface heat flux, urban albedo, ground temperature, and specific humidity depression can be obtained using HCMM satellite data. Values of the ground-specific humidity can be obtained if the distribution of the air-specific humidity is available. More research is required in estimating the absolute magnitude of the specific humidity depression because calculations may be sensitive to model parameters.

Real-time specific surface area measurements via laser-induced breakdown spectroscopy

USGS Publications Warehouse

Washburn, Kathryn E.; Birdwell, Justin E.; Howard, James E.

2017-01-01

From healthcare to cosmetics to environmental science, the specific surface area (SSA) of micro- and mesoporous materials or products can greatly affect their chemical and physical properties. SSA results are also widely used to examine source rocks in conventional and unconventional petroleum resource plays. Despite its importance, current methods to measure SSA are often cumbersome, time-consuming, or require cryogenic consumables (e.g., liquid nitrogen). These methods are not amenable to high-throughput environments, have stringent sample preparation requirements, and are not practical for use in the field. We present a new application of laser-induced breakdown spectroscopy for rapid measurement of SSA. This study evaluates geological samples, specifically organic-rich oil shales, but the approach is expected to be applicable to many other types of materials. The method uses optical emission spectroscopy to examine laser-generated plasma and quantify the amount of argon adsorbed to a sample during an inert gas purge. The technique can accommodate a wide range of sample sizes and geometries and has the potential for field use. These advantages for SSA measurement combined with the simultaneous acquisition of composition information make this a promising new approach for characterizing geologic samples and other materials.

Robotics in cardiac surgery.

PubMed

Vassiliades, Thomas A

2006-03-01

The current status of surgical telemanipulators in the field of cardiac surgery is best described as a device in search of applications, as its role has not been clearly defined. Basic robotic technological research and development needs to focus on two key areas: (a) developing methods for modeling patient and surgical procedures with the ability to employ that customized information in the successful completion of a minimally invasive operation; and (b) developing novel human machine interactions that can overcome the barriers we currently face in performing surgical tasks using telemanipulators. Significant breakthroughs in these areas will then facilitate the construction and employment of enabling robotic systems, each with its specific clinical application. Copyright 2006 John Wiley & Sons, Ltd.

Life sciences and environmental sciences

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1992-02-01

The DOE laboratories play a unique role in bringing multidisciplinary talents -- in biology, physics, chemistry, computer sciences, and engineering -- to bear on major problems in the life and environmental sciences. Specifically, the laboratories utilize these talents to fulfill OHER's mission of exploring and mitigating the health and environmental effects of energy use, and of developing health and medical applications of nuclear energy-related phenomena. At Lawrence Berkeley Laboratory (LBL) support of this mission is evident across the spectrum of OHER-sponsored research, especially in the broad areas of genomics, structural biology, basic cell and molecular biology, carcinogenesis, energy and environment,more » applications to biotechnology, and molecular, nuclear and radiation medicine. These research areas are briefly described.« less

MBE growth of VCSELs for high volume applications

NASA Astrophysics Data System (ADS)

Jäger, Roland; Riedl, Michael C.

2011-05-01

Mass market applications like laser computer mouse or optical data transmission based on vertical-cavity surface-emitting laser (VCSEL) chips need a high over all yield including epitaxy, processing, dicing, mounting and testing. One yield limitation for VCSEL structures is the emission wavelength variation of the substrate surface area leading to the fraction on laser chips which are below or above the specification limits. For most 850 nm VCSEL products a resonator wavelength variation of ±2 nm is common. This represents an average resonator thickness variation of much less than 1% which is quite challenging to be fulfilled on the entire processed wafer surface area. A high over all yield is demonstrated on MBE grown VCSEL structures.

Disseminating Ambient Assisted Living in Rural Areas

PubMed Central

Leitner, Gerhard; Felfernig, Alexander; Fercher, Anton J.; Hitz, Martin

2014-01-01

The smart home, ambient intelligence and ambient assisted living have been intensively researched for decades. Although rural areas are an important potential market, because they represent about 80% of the territory of the EU countries and around 125 million inhabitants, there is currently a lack of applicable AAL solutions. This paper discusses the theoretical foundations of AAL in rural areas. This discussion is underlined by the achievements of the empirical field study, Casa Vecchia, which has been carried out over a four-year period in a rural area in Austria. The major goal of Casa Vecchia was to evaluate the feasibility of a specific form of AAL for rural areas: bringing AAL technology to the homes of the elderly, rather than moving seniors to special-equipped care facilities. The Casa Vecchia project thoroughly investigated the possibilities, challenges and drawbacks of AAL related to this specific approach. The findings are promising and somewhat surprising and indicate that further technical, interactional and socio-psychological research is required to make AAL in rural areas reasonable in the future. PMID:25068862

Synthesis, characterization, antibacterial activity in dark and in vitro cytocompatibility of Ag-incorporated TiO2 microspheres with high specific surface area.

PubMed

Weng, Shengxin; Zhao, Xu; Liu, Guomin; Guan, Yuefeng; Wu, Fanglong; Luo, Yungang

2018-04-23

Postoperative infection associated with medical implants is a devastating complication of orthopedic surgery. Considering the difficulties for the diagnosis and treatment of infection, coating the implant material with antibacterial substances is a promising protocol by which to avoid such an adverse reaction. Nanoparticles (NPs) constructed of anatase microspheres, one form of titanium dioxide (TiO 2 ), with a high specific surface area are fabricated in this study in a facile one-step process using homogeneous precipitation at 90 °C under atmospheric pressure using titanium sulfate (Ti[SO 4 ] 2 ) and urea as the titanium source and precipitant, respectively. The molar ratio of silver (Ag) to TiO 2 can be changed by varying the amount of silver nitrate (AgNO 3 ). The high specific surface area of the TiO 2 microspheres combined with Ag particles (Ag/TiO 2 ) exhibit excellent antibacterial properties against both Staphylococcus aureus and Escherichia coli. In addition, the Ag/TiO 2 material in this work possesses satisfactory biological performance on MC3T3-E1 cells. The high specific surface area of Ag/TiO 2 together with good antibacterial properties and cytocompatibility provide promising applications in dentistry, orthopedics, and other fields of medicine that use biomedical devices.

R&M (Reliability and Maintainability) Program Cost Drivers.

DTIC Science & Technology

1987-05-01

Specific data points used to develop the models (i.e., labor hours mid associated systems and task application characteristics) were obtained from three...study data base used to generate the CER’s em be expanded by adding project data points to the input data given in Appendix 13, adjusting the CER...FRACAS, worst-case/ thermal analyses, stress screening and R-growth. However, the studies did not assign benefits to specific task areas. c. Task

Handling qualities criteria for the space shuttle orbiter during the terminal phase of flight

NASA Technical Reports Server (NTRS)

Stapleford, R. L.; Klein, R. H.; Hob, R. H.

1972-01-01

It was found that large portions of the military handling qualities specification are directly applicable. However a number of additional and substitute criteria are recommended for areas not covered or inadequately covered in the military specification. Supporting pilot/vehicle analyses and simulation experiments were conducted and are described. Results are also presented of analytical and simulator evaluations of three specific interim Orbiter designs which provided a test of the proposed handling qualities criteria. The correlations between the analytical and experimental evaluations were generally excellent.

Fraction Representation: The Not-So-Common Denominator among Textbooks

ERIC Educational Resources Information Center

Hodges, Thomas E.; Cady, JoAnn; Collins, Lee

2008-01-01

Three widely used sixth-grade textbooks were studied to see how fraction concepts were represented. The textbooks selected were "Connected Mathematics," "Middle Grades MathThematics," and Glencoe's "Mathematics: Applications and Concepts Course 1." Three specific areas were examined: representation mode, model, and problem context. Results of…

Organization Development Strategies in Educational Policy Planning and Management.

ERIC Educational Resources Information Center

Jones, B. Kathryn; Biles, Stephen

1990-01-01

This synthesis reviews organizational development (OD) and its decision tools, describes OD applications in educational organizations, explores OD's limitations, and predicts how OD will influence future educational decision making. Findings identify eight specific management and planning areas where OD can be used to improve organizational…

30 CFR 7.81 - Purpose and effective date.

Code of Federal Regulations, 2011 CFR

2011-07-01

... APPROVAL OF MINING PRODUCTS TESTING BY APPLICANT OR THIRD PARTY Diesel Engines Intended for Use in... this subpart E. Subpart E establishes the specific engine performance and exhaust emission requirements for MSHA approval of diesel engines for use in areas of underground coal mines where permissible...

30 CFR 7.81 - Purpose and effective date.

Code of Federal Regulations, 2013 CFR

2013-07-01

... APPROVAL OF MINING PRODUCTS TESTING BY APPLICANT OR THIRD PARTY Diesel Engines Intended for Use in... this subpart E. Subpart E establishes the specific engine performance and exhaust emission requirements for MSHA approval of diesel engines for use in areas of underground coal mines where permissible...

30 CFR 7.81 - Purpose and effective date.

Code of Federal Regulations, 2010 CFR

2010-07-01

... APPROVAL OF MINING PRODUCTS TESTING BY APPLICANT OR THIRD PARTY Diesel Engines Intended for Use in... this subpart E. Subpart E establishes the specific engine performance and exhaust emission requirements for MSHA approval of diesel engines for use in areas of underground coal mines where permissible...

30 CFR 7.81 - Purpose and effective date.

Code of Federal Regulations, 2014 CFR

2014-07-01

... APPROVAL OF MINING PRODUCTS TESTING BY APPLICANT OR THIRD PARTY Diesel Engines Intended for Use in... this subpart E. Subpart E establishes the specific engine performance and exhaust emission requirements for MSHA approval of diesel engines for use in areas of underground coal mines where permissible...

30 CFR 7.81 - Purpose and effective date.

Code of Federal Regulations, 2012 CFR

2012-07-01

... APPROVAL OF MINING PRODUCTS TESTING BY APPLICANT OR THIRD PARTY Diesel Engines Intended for Use in... this subpart E. Subpart E establishes the specific engine performance and exhaust emission requirements for MSHA approval of diesel engines for use in areas of underground coal mines where permissible...

A Legal Brief--Unfulfilled Hiring Promises.

ERIC Educational Resources Information Center

Zirkel, Perry A.; Gluckman, Ivan B.

1988-01-01

Using a specific case, this article reviews some common areas of contract and tort law applicable to principals and employment practices in public and private schools. The question/answer format treats contract validity, negligent misrepresentation, and constitutionality issues involved in a case based on unfulfilled hiring promises. Includes four…

Selection of species and sampling areas: The importance of inference

Treesearch

Paul Stephen Corn

2009-01-01

Inductive inference, the process of drawing general conclusions from specific observations, is fundamental to the scientific method. Platt (1964) termed conclusions obtained through rigorous application of the scientific method as "strong inference" and noted the following basic steps: generating alternative hypotheses; devising experiments, the...

Social Studies Course of Study.

ERIC Educational Resources Information Center

Miller, John E.; Murphy, Terrence A.

This K-12 sequential course of study is the result of one school district's efforts to improve continuity in the social studies curriculum. Following an introduction and statement of philosophy, the program is organized around four basic educational areas--knowledge, application, valuing, and participation. Specific program goals include promoting…

Electro-Analytical Study of Material Interfaces Relevant for Chemical Mechanical Planarization and Lithium Ion Batteries

NASA Astrophysics Data System (ADS)

Turk, Michael C.

This dissertation work involves two areas of experimental research, focusing specifically on the applications of electro-analytical techniques for interfacial material characterization. The first area of the work is centered on the evaluation and characterization of material components used for chemical mechanical planarization (CMP) in the fabrication of semiconductor devices. This part also represents the bulk of the projects undertaken for the present dissertation. The other area of research included here involves exploratory electrochemical studies of certain electrolyte and electrode materials for applications in the development of advanced lithium ion secondary batteries. The common element between the two areas of investigation is the technical approach that combines a broad variety of electro-analytical characterization techniques to examine application specific functions of the associated materials and devices. The CMP related projects concentrate on designing and evaluating materials for CMP slurries that would be useful in the processing of copper interconnects for the sub-22 nm technology node. Specifically, ruthenium and cobalt are nontraditional barrier materials currently considered for the new interconnects. The CMP schemes used to process the structures based on these metals involve complex surface chemistries of Ru, Co and Cu (used for wiring lines). The strict requirement of defect-control while maintaining material removal by precisely regulated tribo-corrosion complicates the designs of the CMP slurries needed to process these systems. Since Ru is electrochemically more noble than Cu, the surface regions of Cu assembled in contact with Ru tend to generate defects due to galvanic corrosion in the CMP environment. At the same time, Co is strongly reactive in the typical slurry environment and is prone to developing galvanic corrosion induced by Cu. The present work explores a selected class of alkaline slurry formulations aimed at reducing these galvanic corrosions in chemically controlled low-pressure CMP. The CMP specific functions of the slurry components are characterized in the tribo-electro-analytical approach by using voltammetry, open circuit potential (OCP) measurements and electrochemical impedance spectroscopy (EIS) in the presence as well as in the absence of surface abrasion, both with and without the inclusion of colloidal silica (SiO2) abrasives. The results are used to understand the reaction mechanisms responsible for supporting material removal and corrosion suppression. The project carried out in the area of Li ion batteries (LIBs) uses electro-analytical techniques to probe electrolyte characteristics as well as electrode material performance. The investigation concentrates on optimizing a tactically chosen set of electrolyte compositions for low-to-moderate temperature applications of lithium titanium oxide (LTO), a relatively new anode material for such batteries. For this application, mixtures of non-aqueous carbonate based solvents are studied in combination with lithium perchlorate. The temperature dependent conductivities of the electrolytes are rigorously measured and analyzed using EIS. The experimental considerations and the working principle of this EIS based approach are carefully examined and standardized in the course of this study. These experiments also investigate the effects of temperature variations (below room temperature) on the solid electrolyte interphase (SEI) formation characteristics of LTO in the given electrolytes. This dissertation is organized as follows: Each experimental system and its relevance for practical applications are briefly introduced in each chapter. The experimental approach and the motivation for carrying out the investigation are also noted in that context. The experimental details specific to the particular study are described. This is followed by the results and their discussion, and subsequently, by the specific conclusions drawn from the given set of experiments. A general summary of the obtained results is presented at the end of the dissertation. Possible extensions of the present studies have also been briefly noted there.

Surveying wearable human assistive technology for life and safety critical applications: standards, challenges and opportunities.

PubMed

Alam, Muhammad Mahtab; Ben Hamida, Elyes

2014-05-23

In this survey a new application paradigm life and safety for critical operations and missions using wearable Wireless Body Area Networks (WBANs) technology is introduced. This paradigm has a vast scope of applications, including disaster management, worker safety in harsh environments such as roadside and building workers, mobile health monitoring, ambient assisted living and many more. It is often the case that during the critical operations and the target conditions, the existing infrastructure is either absent, damaged or overcrowded. In this context, it is envisioned that WBANs will enable the quick deployment of ad-hoc/on-the-fly communication networks to help save many lives and ensuring people's safety. However, to understand the applications more deeply and their specific characteristics and requirements, this survey presents a comprehensive study on the applications scenarios, their context and specific requirements. It explores details of the key enabling standards, existing state-of-the-art research studies, and projects to understand their limitations before realizing aforementioned applications. Application-specific challenges and issues are discussed comprehensively from various perspectives and future research and development directions are highlighted as an inspiration for new innovative solutions. To conclude, this survey opens up a good opportunity for companies and research centers to investigate old but still new problems, in the realm of wearable technologies, which are increasingly evolving and getting more and more attention recently.

Surveying Wearable Human Assistive Technology for Life and Safety Critical Applications: Standards, Challenges and Opportunities

PubMed Central

Alam, Muhammad Mahtab; Ben Hamida, Elyes

2014-01-01

In this survey a new application paradigm life and safety for critical operations and missions using wearable Wireless Body Area Networks (WBANs) technology is introduced. This paradigm has a vast scope of applications, including disaster management, worker safety in harsh environments such as roadside and building workers, mobile health monitoring, ambient assisted living and many more. It is often the case that during the critical operations and the target conditions, the existing infrastructure is either absent, damaged or overcrowded. In this context, it is envisioned that WBANs will enable the quick deployment of ad-hoc/on-the-fly communication networks to help save many lives and ensuring people's safety. However, to understand the applications more deeply and their specific characteristics and requirements, this survey presents a comprehensive study on the applications scenarios, their context and specific requirements. It explores details of the key enabling standards, existing state-of-the-art research studies, and projects to understand their limitations before realizing aforementioned applications. Application-specific challenges and issues are discussed comprehensively from various perspectives and future research and development directions are highlighted as an inspiration for new innovative solutions. To conclude, this survey opens up a good opportunity for companies and research centers to investigate old but still new problems, in the realm of wearable technologies, which are increasingly evolving and getting more and more attention recently. PMID:24859024

The features that distinguish lichenases from other polysaccharide-hydrolyzing enzymes and the relevance of lichenases for biotechnological applications.

PubMed

Goldenkova-Pavlova, Irina V; Tyurin, Alexander А; Mustafaev, Orkhan N

2018-05-01

The main specific features of β-1,3-1,4-glucanases (or lichenases, EC 3.2.1.73), the enzymes that in a strictly specific manner hydrolyze β-glucans of many cereal species and lichens containing β-1,3 and β-1,4 bonds, are reviewed as well as the current strategies used for their protein design, which have been successfully applied to make lichenases more attractive and promising for biocatalytic conversion of biomass, in particular, in the areas of their biotechnological application, such as brewing industry, animal feed manufacture, and biofuel production, which will in future allow these technologies to be economically and ecologically beneficial.

Overview of FAR-TECH's magnetic fusion energy research

NASA Astrophysics Data System (ADS)

Kim, Jin-Soo; Bogatu, I. N.; Galkin, S. A.; Spencer, J. Andrew; Svidzinski, V. A.; Zhao, L.

2017-10-01

FAR-TECH, Inc. has been working on magnetic fusion energy research over two-decades. During the years, we have developed unique approaches to help understanding the physics, and resolving issues in magnetic fusion energy. The specific areas of work have been in modeling RF waves in plasmas, MHD modeling and mode-identification, and nano-particle plasma jet and its application to disruption mitigation. Our research highlights in recent years will be presented with examples, specifically, developments of FullWave (Full Wave RF code), PMARS (Parallelized MARS code), and HEM (Hybrid ElectroMagnetic code). In addition, nano-particle plasma-jet (NPPJ) and its application for disruption mitigation will be presented. Work is supported by the U.S. DOE SBIR program.

Silk fibroin as biomaterial for bone tissue engineering.

PubMed

Melke, Johanna; Midha, Swati; Ghosh, Sourabh; Ito, Keita; Hofmann, Sandra

2016-02-01

Silk fibroin (SF) is a fibrous protein which is produced mainly by silkworms and spiders. Its unique mechanical properties, tunable biodegradation rate and the ability to support the differentiation of mesenchymal stem cells along the osteogenic lineage, have made SF a favorable scaffold material for bone tissue engineering. SF can be processed into various scaffold forms, combined synergistically with other biomaterials to form composites and chemically modified, which provides an impressive toolbox and allows SF scaffolds to be tailored to specific applications. This review discusses and summarizes recent advancements in processing SF, focusing on different fabrication and functionalization methods and their application to grow bone tissue in vitro and in vivo. Potential areas for future research, current challenges, uncertainties and gaps in knowledge are highlighted. Silk fibroin is a natural biomaterial with remarkable biomedical and mechanical properties which make it favorable for a broad range of bone tissue engineering applications. It can be processed into different scaffold forms, combined synergistically with other biomaterials to form composites and chemically modified which provides a unique toolbox and allows silk fibroin scaffolds to be tailored to specific applications. This review discusses and summarizes recent advancements in processing silk fibroin, focusing on different fabrication and functionalization methods and their application to grow bone tissue in vitro and in vivo. Potential areas for future research, current challenges, uncertainties and gaps in knowledge are highlighted. Copyright © 2015 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Leaf-IT: An Android application for measuring leaf area.

PubMed

Schrader, Julian; Pillar, Giso; Kreft, Holger

2017-11-01

The use of plant functional traits has become increasingly popular in ecological studies because plant functional traits help to understand key ecological processes in plant species and communities. This also includes changes in diversity, inter- and intraspecific interactions, and relationships of species at different spatiotemporal scales. Leaf traits are among the most important traits as they describe key dimensions of a plant's life history strategy. Further, leaf area is a key parameter with relevance for other traits such as specific leaf area, which in turn correlates with leaf chemical composition, photosynthetic rate, leaf longevity, and carbon investment. Measuring leaf area usually involves the use of scanners and commercial software and can be difficult under field conditions. We present Leaf-IT, a new smartphone application for measuring leaf area and other trait-related areas. Leaf-IT is free, designed for scientific purposes, and runs on Android 4 or higher. We tested the precision and accuracy using objects with standardized area and compared the area measurements of real leaves with the well-established, commercial software WinFOLIA using the Altman-Bland method. Area measurements of standardized objects show that Leaf-IT measures area with high accuracy and precision. Area measurements with Leaf-IT of real leaves are comparable to those of WinFOLIA. Leaf-IT is an easy-to-use application running on a wide range of smartphones. That increases the portability and use of Leaf-IT and makes it possible to measure leaf area under field conditions typical for remote locations. Its high accuracy and precision are similar to WinFOLIA. Currently, its main limitation is margin detection of damaged leaves or complex leaf morphologies.

Therapeutic Applications of Herbal Medicines for Cancer Patients

PubMed Central

Yin, Shu-Yi; Wei, Wen-Chi; Jian, Feng-Yin; Yang, Ning-Sun

2013-01-01

Medicinal herbs and their derivative phytocompounds are being increasingly recognized as useful complementary treatments for cancer. A large volume of clinical studies have reported the beneficial effects of herbal medicines on the survival, immune modulation, and quality of life (QOL) of cancer patients, when these herbal medicines are used in combination with conventional therapeutics. Here, we briefly review some examples of clinical studies that investigated the use of herbal medicines for various cancers and the development of randomized controlled trials (RCTs) in this emerging research area. In addition, we also report recent studies on the biochemical and cellular mechanisms of herbal medicines in specific tumor microenvironments and the potential application of specific phytochemicals in cell-based cancer vaccine systems. This review should provide useful technological support for evidence-based application of herbal medicines in cancer therapy. PMID:23956768

ALARA implementation throughout project life cycle

DOE Office of Scientific and Technical Information (OSTI.GOV)

Haynes, M.J.

1995-03-01

A strength of radiation protection programs generally has been endorsement and application of the ALARA principle. In Ontario Hydro, which currently operates 20 commercial size nuclear units, great strides have been made in the last three decades in reducing occupational radiation exposure per unit of electricity generated. This paper will discuss specific applications of elements of the overall ALARA program which have most contributed to dose reduction as the nuclear program has expanded. This includes such things as management commitment, ALARA application in the design phase and major rehabilitation work, the benefits of the self protection concept, a specific examplemore » of elimination (or reduction) of the source term and the importance of dose targets. Finally, it is concluded that the major opportunities for further improvements may lie in the area of information management.« less

Freely available compound data sets and software tools for chemoinformatics and computational medicinal chemistry applications

PubMed Central

Bajorath, Jurgen

2012-01-01

We have generated a number of  compound data sets and programs for different types of applications in pharmaceutical research. These data sets and programs were originally designed for our research projects and are made publicly available. Without consulting original literature sources, it is difficult to understand specific features of data sets and software tools, basic ideas underlying their design, and applicability domains. Currently, 30 different entries are available for download from our website. In this data article, we provide an overview of the data and tools we make available and designate the areas of research for which they should be useful. For selected data sets and methods/programs, detailed descriptions are given. This article should help interested readers to select data and tools for specific computational investigations. PMID:24358818

Domain specific software architectures: Command and control

NASA Technical Reports Server (NTRS)

Braun, Christine; Hatch, William; Ruegsegger, Theodore; Balzer, Bob; Feather, Martin; Goldman, Neil; Wile, Dave

1992-01-01

GTE is the Command and Control contractor for the Domain Specific Software Architectures program. The objective of this program is to develop and demonstrate an architecture-driven, component-based capability for the automated generation of command and control (C2) applications. Such a capability will significantly reduce the cost of C2 applications development and will lead to improved system quality and reliability through the use of proven architectures and components. A major focus of GTE's approach is the automated generation of application components in particular subdomains. Our initial work in this area has concentrated in the message handling subdomain; we have defined and prototyped an approach that can automate one of the most software-intensive parts of C2 systems development. This paper provides an overview of the GTE team's DSSA approach and then presents our work on automated support for message processing.

Estimating normative limits of Heidelberg Retina Tomograph optic disc rim area with quantile regression.

PubMed

Artes, Paul H; Crabb, David P

2010-01-01

To investigate why the specificity of the Moorfields Regression Analysis (MRA) of the Heidelberg Retina Tomograph (HRT) varies with disc size, and to derive accurate normative limits for neuroretinal rim area to address this problem. Two datasets from healthy subjects (Manchester, UK, n = 88; Halifax, Nova Scotia, Canada, n = 75) were used to investigate the physiological relationship between the optic disc and neuroretinal rim area. Normative limits for rim area were derived by quantile regression (QR) and compared with those of the MRA (derived by linear regression). Logistic regression analyses were performed to quantify the association between disc size and positive classifications with the MRA, as well as with the QR-derived normative limits. In both datasets, the specificity of the MRA depended on optic disc size. The odds of observing a borderline or outside-normal-limits classification increased by approximately 10% for each 0.1 mm(2) increase in disc area (P < 0.1). The lower specificity of the MRA with large optic discs could be explained by the failure of linear regression to model the extremes of the rim area distribution (observations far from the mean). In comparison, the normative limits predicted by QR were larger for smaller discs (less specific, more sensitive), and smaller for larger discs, such that false-positive rates became independent of optic disc size. Normative limits derived by quantile regression appear to remove the size-dependence of specificity with the MRA. Because quantile regression does not rely on the restrictive assumptions of standard linear regression, it may be a more appropriate method for establishing normative limits in other clinical applications where the underlying distributions are nonnormal or have nonconstant variance.

Providing Geospatial Education and Real World Applications of Data across the Climate Initiative Themes

NASA Astrophysics Data System (ADS)

Weigel, A. M.; Griffin, R.; Bugbee, K.

2015-12-01

Various organizations such as the Group on Earth Observations (GEO) have developed a structure for general thematic areas in Earth science research, however the Climate Data Initiative (CDI) is addressing the challenging goal of organizing such datasets around core themes specifically related to climate change impacts. These thematic areas, which currently include coastal flooding, food resilience, ecosystem vulnerability, water, transportation, energy infrastructure, and human health, form the core of a new college course at the University of Alabama in Huntsville developed around real-world applications in the Earth sciences. The goal of this course is to educate students on the data available and scope of GIS applications in Earth science across the CDI climate themes. Real world applications and datasets serve as a pedagogical tool that provide a useful medium for instruction in scientific geospatial analysis and GIS software. With a wide range of potential research areas that fall under the rubric of "Earth science", thematic foci can help to structure a student's understanding of the potential uses of GIS across sub-disciplines, while communicating core data processing concepts. The learning modules and use-case scenarios for this course demonstrate the potential applications of CDI data to undergraduate and graduate Earth science students.

Recent developments in refractive concentrators for space photovoltaic power systems

NASA Technical Reports Server (NTRS)

Piszczor, Michael F.; Oneill, Mark J.

1993-01-01

Since SPRAT 11, significant progress has been made in the development of refractive concentrator elements and components designed specifically for space applications. The status of the mini-dome Fresnel lens concentrator array is discussed and then the results of work recently completed in the area of prismatic cell covers for concentrator systems are summarized. This is followed by a brief discussion of some work just starting in the area of line-focus refractive concentrators for space.

Protein–Hydrogel Interactions in Tissue Engineering: Mechanisms and Applications

PubMed Central

Zustiak, Silviya P.; Wei, Yunqian

2013-01-01

Recent advances in our understanding of the sophistication of the cellular microenvironment and the dynamics of tissue remodeling during development, disease, and regeneration have increased our appreciation of the current challenges facing tissue engineering. As this appreciation advances, we are better equipped to approach problems in the biology and therapeutics of even more complex fields, such as stem cells and cancer. To aid in these studies, as well as the established areas of tissue engineering, including cardiovascular, musculoskeletal, and neural applications, biomaterials scientists have developed an extensive array of materials with specifically designed chemical, mechanical, and biological properties. Herein, we highlight an important topic within this area of biomaterials research, protein–hydrogel interactions. Due to inherent advantages of hydrated scaffolds for soft tissue engineering as well as specialized bioactivity of proteins and peptides, this field is well-posed to tackle major needs within emerging areas of tissue engineering. We provide an overview of the major modes of interactions between hydrogels and proteins (e.g., weak forces, covalent binding, affinity binding), examples of applications within growth factor delivery and three-dimensional scaffolds, and finally future directions within the area of hydrogel–protein interactions that will advance our ability to control the cell–biomaterial interface. PMID:23150926

Technology and Economics, Inc. Technology Application Team

NASA Technical Reports Server (NTRS)

Ballard, T.; Macfadyen, D. J.

1981-01-01

Technology + Economics, Inc. (T+E), under contract to the NASA Headquarters Technology Transfer Division, operates a Technology Applications Team (TATeam) to assist in the transfer of NASA-developed aerospace technology. T+E's specific areas of interest are selected urban needs at the local, county, and state levels. T+E contacts users and user agencies at the local, state, and county levels to assist in identifying significant urban needs amenable to potential applications of aerospace technology. Once viable urban needs have been identified in this manner, or through independent research, T+E searches the NASA technology database for technology and/or expertise applicable to the problem. Activities currently under way concerning potential aerospace applications are discussed.

Computational and mathematical methods in brain atlasing.

PubMed

Nowinski, Wieslaw L

2017-12-01

Brain atlases have a wide range of use from education to research to clinical applications. Mathematical methods as well as computational methods and tools play a major role in the process of brain atlas building and developing atlas-based applications. Computational methods and tools cover three areas: dedicated editors for brain model creation, brain navigators supporting multiple platforms, and atlas-assisted specific applications. Mathematical methods in atlas building and developing atlas-aided applications deal with problems in image segmentation, geometric body modelling, physical modelling, atlas-to-scan registration, visualisation, interaction and virtual reality. Here I overview computational and mathematical methods in atlas building and developing atlas-assisted applications, and share my contribution to and experience in this field.

Wireless Technology Use Case Requirement Analysis for Future Space Applications

NASA Technical Reports Server (NTRS)

Abedi, Ali; Wilkerson, DeLisa

2016-01-01

This report presents various use case scenarios for wireless technology -including radio frequency (RF), optical, and acoustic- and studies requirements and boundary conditions in each scenario. The results of this study can be used to prioritize technology evaluation and development and in the long run help in development of a roadmap for future use of wireless technology. The presented scenarios cover the following application areas: (i) Space Vehicles (manned/unmanned), (ii) Satellites and Payloads, (iii) Surface Explorations, (iv) Ground Systems, and (v) Habitats. The requirement analysis covers two parallel set of conditions. The first set includes the environmental conditions such as temperature, radiation, noise/interference, wireless channel characteristics and accessibility. The second set of requirements are dictated by the application and may include parameters such as latency, throughput (effective data rate), error tolerance, and reliability. This report provides a comprehensive overview of all requirements from both perspectives and details their effects on wireless system reliability and network design. Application area examples are based on 2015 NASA Technology roadmap with specific focus on technology areas: TA 2.4, 3.3, 5.2, 5.5, 6.4, 7.4, and 10.4 sections that might benefit from wireless technology.

Proceedings of the 7th Annual Precise Time and Time Interval (PTTI) Applications and Planning Meeting

NASA Technical Reports Server (NTRS)

1975-01-01

The Proceedings contain the papers presented at the Seventh Annual Precise Time and Time Interval (PTTI) Applications and Planning Meeting and the edited record of the discussion period following each paper. This meeting provided a forum to promote more effective, efficient, economical and skillful applications of PTTI technology to the many problem areas to which PTTI offers solutions. Specifically the purpose of the meeting is to: disseminate, coordinate, and exchange practical information associated with precise time and frequency; acquaint systems engineers, technicians and managers with precise time and frequency technology and its applications; and review present and future requirements for PTTI.

Industrial applications of automated X-ray inspection

NASA Astrophysics Data System (ADS)

Shashishekhar, N.

2015-03-01

Many industries require that 100% of manufactured parts be X-ray inspected. Factors such as high production rates, focus on inspection quality, operator fatigue and inspection cost reduction translate to an increasing need for automating the inspection process. Automated X-ray inspection involves the use of image processing algorithms and computer software for analysis and interpretation of X-ray images. This paper presents industrial applications and illustrative case studies of automated X-ray inspection in areas such as automotive castings, fuel plates, air-bag inflators and tires. It is usually necessary to employ application-specific automated inspection strategies and techniques, since each application has unique characteristics and interpretation requirements.

Environmental risk analysis of oil handling facilities in port areas. Application to Tarragona harbor (NE Spain).

PubMed

Valdor, Paloma F; Gómez, Aina G; Puente, Araceli

2015-01-15

Diffuse pollution from oil spills is a widespread problem in port areas (as a result of fuel supply, navigation and loading/unloading activities). This article presents a method to assess the environmental risk of oil handling facilities in port areas. The method is based on (i) identification of environmental hazards, (ii) characterization of meteorological and oceanographic conditions, (iii) characterization of environmental risk scenarios, and (iv) assessment of environmental risk. The procedure has been tested by application to the Tarragona harbor. The results show that the method is capable of representing (i) specific local pollution cases (i.e., discriminating between products and quantities released by a discharge source), (ii) oceanographic and meteorological conditions (selecting a representative subset data), and (iii) potentially affected areas in probabilistic terms. Accordingly, it can inform the design of monitoring plans to study and control the environmental impact of these facilities, as well as the design of contingency plans. Copyright © 2014 Elsevier Ltd. All rights reserved.

Why trash don't pass? pharmaceutical licensing and safety performance of drugs.

PubMed

Banerjee, Tannista; Nayak, Arnab

2017-01-01

This paper examines how asymmetric information in pharmaceutical licensing affects the safety standards of licensed drugs. Pharmaceutical companies often license potential drug molecules at different stages of drug development from other pharmaceutical or biotechnology companies and complete the remaining of research stages before submitting the new drug application(NDA) to the food and drug administration. The asymmetric information associated with the quality of licensed molecules might result in the molecules which are less likely to succeed to be licensed out, while those with greater potential of success being held internally for development. We identify the NDAs submitted between 1993 and 2004 where new molecular entities were acquired through licensing. Controlling for other drug area specific and applicant firm specific factors, we investigate whether drugs developed with licensed molecules face higher probability of safety based recall and ultimate withdrawal from the market than drugs developed internally. Results suggest the opposite of Akerlof's (Q J Econ 84:488-500, 1970) lemons problem. Licensed molecules rather have less probability of facing safety based recalls and ultimate withdrawal from the market comparing to internally developed drug molecules. This suggests that biotechnology and small pharmaceutical firms specializing in pharmaceutical research are more efficient in developing good potential molecules because of their concentrated research. Biotechnology firms license out good potential molecules because it increases their market value and reputation. In addition, results suggest that both the number of previous approved drugs in the disease area, and also the applicant firms' total number of previous approvals in all disease areas reduce the probability that an additional approved drug in the same drug area will potentially be harmful.

Evaluation of early-season baculovirus treatment for suppression of Heliothis virescens and Helicouverpa zea (Lepidoptera: Noctuidae) over a wide area

Treesearch

Jane Leslie Hayes; Marion Bell

1994-01-01

Pheromone trap counts of F1 male cotton bollworm, Helicoverpa zea (Bodie), and tobacco budworm, Heliothis virescens (F1) were used to assess the effect of areawide suppression achieved by early-season application of a Heliocoverpa/Heliothis specific nuclear...

Benefit transfer with limited data: An application to recreational fishing losses from surface mining

EPA Science Inventory

The challenges of applying benefit transfer models to policy sites are often underestimated. Analysts commonly need to estimate site-specific effects for areas that lack data on the number of people who use the resource, intensity of use, and other relevant variables. Yet, the be...

Dual mode nuclear rocket system applications.

NASA Technical Reports Server (NTRS)

Boretz, J. E.; Bell, J. M.; Plebuch, R. K.; Priest, C. C.

1972-01-01

Mission areas where the dual-mode nuclear rocket system is superior to nondual-mode systems are demonstrated. It is shown that the dual-mode system is competitive with the nondual-mode system even for those specific missions and particular payload configurations where it does not have a clear-cut advantage.

7 CFR 225.7 - Program monitoring and assistance.

Code of Federal Regulations, 2011 CFR

2011-01-01

... school closures during the period from October through April (or at any time of the year in an area with... available all necessary Program materials in sufficient time to enable applicant sponsors to prepare adequately for the Program. (c) Food specifications and meal quality standards. With the assistance of the...

Model for Characterizing and Creating Certificate Programs in Technology-Specific Areas,

DTIC Science & Technology

1996-05-01

the TOEFL for applicants whose first language is not English. • GRE general and subject test. • Demonstrated competency in <prerequisites for...least 2.75 • English competency as demonstrated by TOEFL • Competence in data structures • Introductory level course in software engineering Course

Activities of the Remote Sensing Information Sciences Research Group

NASA Technical Reports Server (NTRS)

Estes, J. E.; Botkin, D.; Peuquet, D.; Smith, T.; Star, J. L. (Principal Investigator)

1984-01-01

Topics on the analysis and processing of remotely sensed data in the areas of vegetation analysis and modelling, georeferenced information systems, machine assisted information extraction from image data, and artificial intelligence are investigated. Discussions on support field data and specific applications of the proposed technologies are also included.

78 FR 54383 - Airworthiness Directives; Eurocopter Deutschland GmbH Helicopters

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-04

... the main transmission filter housing upper part and modifying the main transmission housing upper part... filter area was not manufactured in accordance with applicable design specifications. The actions of this... a corrugated washer in the filter housing of the housing upper part and modifying each affected main...

Incorporating "omics" in the study of reproduction and development: Virtual Tissue Models in Developmental Toxicity Research

EPA Science Inventory

In recent years, ground breaking research in genomic applications in the area of reproductive and developmental toxicology have been successful in linking changes in the expression of specific genes and their higher-level biological processes to effects induced by drugs or chemic...

Direct Multizone System -- DMS1-275.

ERIC Educational Resources Information Center

Lennox Industries, Inc., Marshalltown, IA.

Lennox Direct Multizone System as a new concept for integrated comfort control is described. The following areas of concern are included--(1) flexibility - typical applications, (2) detailed engineering data, (3) accessories, (4) approvals, (5) guide specifications, (6) dimensional drawings of a typical unit, (7) blower data, (8) mounting data,…

Establishing a Child Care Substitute Caregiver System.

ERIC Educational Resources Information Center

Love, Lynne

Substitute caregivers are needed by day care centers in every state. Indeed, some areas are experiencing severe shortages of applicants for child care positions and short-term substitute work. This article describes problems encountered in current substitute caregiver systems and suggests ways of dealing with such problems. Specifically discussed…

Estimating total forest biomass in Maine, 1995

Treesearch

Eric H. Wharton; Douglas M. Griffith; Douglas M. Griffith

1998-01-01

Presents methods for synthesizing information from existing biomass literature for estimating biomass over extensive forest areas with specific applications to Maine. Tables of appropriate regression equations and the tree and shrub species to which these equations can be applied are presented as well as biomass estimates at the county and state level.

Manufacturing process applications team (MATeam)

NASA Technical Reports Server (NTRS)

Bangs, E. R.

1980-01-01

Progress in the transfer of aerospace technology to solve key problems in the manufacturing sector of the economy is reported. Potential RTOP programs are summarized along with dissemination activities. The impact of transferred NASA manufacturing technology is discussed. Specific areas covered include aircraft production, robot technology, machining of alloys, and electrical switching systems.

78 FR 72643 - Taking of Marine Mammals Incidental to Specified Activities: Mukilteo Ferry Terminal Construction...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-03

.... ACTION: Notice; proposed incidental harassment authorization; request for comments and information... revised IHA application. The action discussed in this document is based on WSF's October 17, 2013, IHA... these species. Specific information concerning these species in the vicinity of the proposed action area...

Commercial perspective in THz spectroscopy, sensing and imaging (Conference Presentation)

NASA Astrophysics Data System (ADS)

Bouyé, Clémentine; Taoudi, Sarah; Cochard, Jacques; d'Humières, Benoît

2017-02-01

For their ability to be transmitted by materials opaque in the visible and IR ranges (clothes, plastic, …), for being non-ionizing, for providing sub-mm resolution imaging, for the specific signatures of numerous materials, Terahertz waves - ranging from 200 GHz to 10 THz - have been raising the interest of industrials for about fifteen years. This study focuses on the penetration of THz technologies into the industrial applications driving the THz market growth at short and long term: Non Destructive testing (NDT), Defense and Security, Biomedical. For 15 years, Terahertz technologies have been continuously tested on a wide variety of applications. Thanks to these ongoing feasibility studies, manufacturers and end-users gained a deeper knowledge about the abilities and the limitations of the different Terahertz systems (Time-Domain spectroscopy, Frequency-Domain spectroscopy, Time-Domain reflectometry, etc). The demand from end-users is more qualified and is segmented as follows: 1. Detection of objects and defects on large areas 2. Thickness measurement on large areas 3. Chemical and Structural characterization of small objects and defects on small areas (2D) or volumes (3D) Each of these 3 functions leads to a specific family of THz systems with distinct requirements in terms of performance and cost: 1. Detection: cheap and compact imaging systems. 2. Thickness measurement: cost-effective and high speed systems. 3. Characterization: high resolution, high reliability and real-time sensing systems. This article will present the existing and incoming THz systems and components addressing each function. Terahertz technologies are currently finding their place on the market, outside research and scientific applications. The objective of this article is to identify the industrial applications where THz techniques will be adopted and to provide market growth perspectives.

TT-C-490 -Implementing Alternatives Through Specifications (Briefing Charts)

DTIC Science & Technology

2014-11-18

currently valid OMB control number. 1. REPORT DATE 18 NOV 2014 2. REPORT TYPE 3. DATES COVERED 00-00-2014 to 00-00-2014 4. TITLE AND SUBTITLE TT-C...Existing Pretreatments for CARC Coating System TT-C-490E – Pretreatments specific for ferrous substrates – Specifies either zinc phosphate conversion...Only pretreatment allowed for multi- metal application – Zinc phosphate is either applied by immersion or spray in a contained area Prior to 2013

Wide band gap Ga2O3 as efficient UV-C photocatalyst for gas-phase degradation applications.

PubMed

Jędrzejczyk, Marcin; Zbudniewek, Klaudia; Rynkowski, Jacek; Keller, Valérie; Grams, Jacek; Ruppert, Agnieszka M; Keller, Nicolas

2017-12-01

α, β, γ, and δ polymorphs of 4.6-4.8 eV wide band gap Ga 2 O 3 photocatalysts were prepared via a soft chemistry route. Their photocatalytic activity under 254 nm UV-C light in the degradation of gaseous toluene was strongly depending on the polymorph phase. α- and β-Ga 2 O 3 photocatalysts enabled achieving high and stable conversions of toluene with selectivities to CO 2 within the 50-90% range, by contrast to conventional TiO 2 photocatalysts that fully deactivate very rapidly on stream in similar operating conditions with rather no CO 2 production, no matter whether UV-A or UV-C light was used. The highest performances were achieved on the high specific surface area β-Ga 2 O 3 photocatalyst synthesized by adding polyethylene glycol (PEG) as porogen before precipitation, with stable toluene conversion and mineralization rate into CO 2 strongly overcoming those obtained on commercial β-Ga 2 O 3 . They were attributed to favorable physicochemical properties in terms of high specific surface area, small mean crystallite size, good crystallinity, high pore volume with large size mesopore distribution and appropriate surface acidity, and to the possible existence of a double local internal field within Ga 3+ units. In the degradation of hydrogen sulfide, PEG-derived β-Ga 2 O 3 takes advantage from its high specific surface area for storing sulfate, and thus for increasing its resistance to deactivation and the duration at total sulfur removal when compared to other β-Ga 2 O 3 photocatalysts. So, we illustrated the interest of using high surface area β-Ga 2 O 3 in environmental photocatalysis for gas-phase depollution applications.

The Sunrise project: An R&D project for a national information infrastructure prototype

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Juhnyoung

1995-02-01

Sunrise is a Los Alamos National Laboratory (LANL) project started in October 1993. It is intended to a prototype National Information Infrastructure (NII) development project. A main focus of Sunrise is to tie together enabling technologies (networking, object-oriented distributed computing, graphical interfaces, security, multimedia technologies, and data mining technologies) with several specific applications. A diverse set of application areas was chosen to ensure that the solutions developed in the project are as generic as possible. Some of the application areas are materials modeling, medical records and image analysis, transportation simulations, and education. This paper provides a description of Sunrise andmore » a view of the architecture and objectives of this evolving project. The primary objectives of Sunrise are three-fold: (1) To develop common information-enabling tools for advanced scientific research and its applications to industry; (2) To enhance the capabilities of important research programs at the Laboratory; and (3) To define a new way of collaboration between computer science and industrially relevant research.« less

A network-based distributed, media-rich computing and information environment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Phillips, R.L.

1995-12-31

Sunrise is a Los Alamos National Laboratory (LANL) project started in October 1993. It is intended to be a prototype National Information Infrastructure development project. A main focus of Sunrise is to tie together enabling technologies (networking, object-oriented distributed computing, graphical interfaces, security, multi-media technologies, and data-mining technologies) with several specific applications. A diverse set of application areas was chosen to ensure that the solutions developed in the project are as generic as possible. Some of the application areas are materials modeling, medical records and image analysis, transportation simulations, and K-12 education. This paper provides a description of Sunrise andmore » a view of the architecture and objectives of this evolving project. The primary objectives of Sunrise are three-fold: (1) To develop common information-enabling tools for advanced scientific research and its applications to industry; (2) To enhance the capabilities of important research programs at the Laboratory; (3) To define a new way of collaboration between computer science and industrially-relevant research.« less

Theorem Proving In Higher Order Logics

NASA Technical Reports Server (NTRS)

Carreno, Victor A. (Editor); Munoz, Cesar A.; Tahar, Sofiene

2002-01-01

The TPHOLs International Conference serves as a venue for the presentation of work in theorem proving in higher-order logics and related areas in deduction, formal specification, software and hardware verification, and other applications. Fourteen papers were submitted to Track B (Work in Progress), which are included in this volume. Authors of Track B papers gave short introductory talks that were followed by an open poster session. The FCM 2002 Workshop aimed to bring together researchers working on the formalisation of continuous mathematics in theorem proving systems with those needing such libraries for their applications. Many of the major higher order theorem proving systems now have a formalisation of the real numbers and various levels of real analysis support. This work is of interest in a number of application areas, such as formal methods development for hardware and software application and computer supported mathematics. The FCM 2002 consisted of three papers, presented by their authors at the workshop venue, and one invited talk.

Conformal Microwave Array (CMA) Applicators for Hyperthermia of Diffuse Chestwall Recurrence

PubMed Central

Stauffer, Paul R.; Maccarini, Paolo; Arunachalam, Kavitha; Craciunescu, Oana; Diederich, Chris; Juang, Titania; Rossetto, Francesca; Schlorff, Jaime; Milligan, Andrew; Hsu, Joe; Sneed, Penny; Vujaskovic, Zeljko

2010-01-01

Purpose This article summarizes the evolution of microwave array applicators for heating large area chestwall disease as an adjuvant to external beam radiation, systemic chemotherapy, and potentially simultaneous brachytherapy. Methods Current devices used for thermotherapy of chestwall recurrence are reviewed. The largest conformal array applicator to date is evaluated in four studies: i) ability to conform to the torso is demonstrated with a CT scan of a torso phantom and MR scan of the conformal waterbolus component on a mastectomy patient; ii) Specific Absorption Rate (SAR) and temperature distributions are calculated with electromagnetic and thermal simulation software for a mastectomy patient; iii). SAR patterns are measured with a scanning SAR probe in liquid muscle phantom for a buried coplanar waveguide CMA; and iv) heating patterns and patient tolerance of CMA applicators are characterized in a clinical pilot study with 13 patients. Results CT and MR scans demonstrate excellent conformity of CMA applicators to contoured anatomy. Simulations demonstrate effective control of heating over contoured anatomy. Measurements confirm effective coverage of large treatment areas with no gaps. In 42 hyperthermia treatments, CMA applicators provided well-tolerated effective heating of up to 500cm2 regions, achieving target temperatures of Tmin=41.4±0.7°C, T90=42.1±0.6°C, Tave=42.8±0.6°C, and Tmax=44.3±0.8°C as measured in an average of 90 points per treatment. Summary The CMA applicator is an effective thermal therapy device for heating large-area superficial disease such as diffuse chestwall recurrence. It is able to cover over three times the treatment area of conventional hyperthermia devices while conforming to typical body contours. PMID:20849262

[The principle of registration, evaluation and testing of disinfecting preparations].

PubMed

Röhm-Rodowald, Ewa; Jakimiak, Bozenna; Podgórska, Marta

2008-01-01

Disinfectants are used to produce a state in which the number of living micro-organisms has been reduced to a level which is appropriate to the practical situation. For any products which are included in the Biocidal Directive 98/8/EC, for which specific activity is claimed, test data has to be approved by the regulatory authority and a product license obtained before the product can be offered for sale. Disinfectants can be recorded as biocidal products or medical devices. Presently, it is possible to measure the activity of a product on defined micro-organisms in specified experimental conditions. Efficacy is the result of the use of a product according to a defined application. To allow different requirements in different areas of application, separate tests and pass criteria have been or will be prepared for each of following three areas of application: medical, veterinary and group comprising food, industrial, domestic and institutional areas. The laboratory methods to be used for testing the activity of chemical disinfectants meets the European standards. The tests are categorised on a modular basis as follows: phase 1 tests, phase 2 step 1 tests, phase 2 step 2 tests and phase 3 tests. In order to claim that a product has disinfectant properties, suitable for use in the medical area, the product shall be tested according to European standards: phase 2 step 1 tests, phase 2 step 2 tests. Phase 1 tests are not required to support claims for chemical disinfectants used in human medicine. Only phase 1 tests are required to support claims for active substances for which no particular area of application is specified. Medical devices are subjects to the European Directive 93/42/EEC which requires that a product must carry a CE mark. Disinfectants which are intended specifically by its manufacturer to be used on medical devices are themselves medical devices and so these products, as well as conforming to the instrument disinfection European standards as specified in EN 14885, are also required to carry a CE mark.

Molecularly Imprinted Nanomaterials for Sensor Applications

PubMed Central

Irshad, Muhammad; Iqbal, Naseer; Mujahid, Adnan; Afzal, Adeel; Hussain, Tajamal; Sharif, Ahsan; Ahmad, Ejaz; Athar, Muhammad Makshoof

2013-01-01

Molecular imprinting is a well-established technology to mimic antibody-antigen interaction in a synthetic platform. Molecularly imprinted polymers and nanomaterials usually possess outstanding recognition capabilities. Imprinted nanostructured materials are characterized by their small sizes, large reactive surface area and, most importantly, with rapid and specific analysis of analytes due to the formation of template driven recognition cavities within the matrix. The excellent recognition and selectivity offered by this class of materials towards a target analyte have found applications in many areas, such as separation science, analysis of organic pollutants in water, environmental analysis of trace gases, chemical or biological sensors, biochemical assays, fabricating artificial receptors, nanotechnology, etc. We present here a concise overview and recent developments in nanostructured imprinted materials with respect to various sensor systems, e.g., electrochemical, optical and mass sensitive, etc. Finally, in light of recent studies, we conclude the article with future perspectives and foreseen applications of imprinted nanomaterials in chemical sensors. PMID:28348356

Functionality in Electrospun Nanofibrous Membranes Based on Fiber's Size, Surface Area, and Molecular Orientation

PubMed Central

Matsumoto, Hidetoshi; Tanioka, Akihiko

2011-01-01

Electrospinning is a versatile method for forming continuous thin fibers based on an electrohydrodynamic process. This method has the following advantages: (i) the ability to produce thin fibers with diameters in the micrometer and nanometer ranges; (ii) one-step forming of the two- or three-dimensional nanofiber network assemblies (nanofibrous membranes); and (iii) applicability for a broad spectrum of molecules, such as synthetic and biological polymers and polymerless sol-gel systems. Electrospun nanofibrous membranes have received significant attention in terms of their practical applications. The major advantages of nanofibers or nanofibrous membranes are the functionalities based on their nanoscaled-size, highly specific surface area, and highly molecular orientation. These functionalities of the nanofibrous membranes can be controlled by their fiber diameter, surface chemistry and topology, and internal structure of the nanofibers. This report focuses on our studies and describes fundamental aspects and applications of electrospun nanofibrous membranes. PMID:24957735

Networking and AI systems: Requirements and benefits

NASA Technical Reports Server (NTRS)

1988-01-01

The price performance benefits of network systems is well documented. The ability to share expensive resources sold timesharing for mainframes, department clusters of minicomputers, and now local area networks of workstations and servers. In the process, other fundamental system requirements emerged. These have now been generalized with open system requirements for hardware, software, applications and tools. The ability to interconnect a variety of vendor products has led to a specification of interfaces that allow new techniques to extend existing systems for new and exciting applications. As an example of the message passing system, local area networks provide a testbed for many of the issues addressed by future concurrent architectures: synchronization, load balancing, fault tolerance and scalability. Gold Hill has been working with a number of vendors on distributed architectures that range from a network of workstations to a hypercube of microprocessors with distributed memory. Results from early applications are promising both for performance and scalability.

Intercomparison of different operational oceanographic forecast products in the CMEMS IBI area

NASA Astrophysics Data System (ADS)

Lorente, Pablo; Sotillo, Marcos G.; Dabrowski, Tomasz; Amo-Baladrón, Arancha; Aznar, Roland; De Pascual, Alvaro; Levier, Bruno; Bowyer, Peter; Cossarini, Gianpiero; Salon, Stefano; Tonani, Marina; Alvarez-Fanjul, Enrique

2017-04-01

The development of skill assessment software packages and dedicated web applications is a relatively novel theme in operational oceanography. Within the CMEMS IBI-MFC, the quality of IBI (Iberia-Biscay-Ireland) forecast products is assessed by means of NARVAL (North Atlantic Regional VALidation) web-based tool. The validation of IBI against independent in situ and remote-sensing measurements is routinely conducted to evaluate model's veracity and prognostic capabilities. Noticeable efforts are in progress to define meaningful skill scores and statistical metrics to quantitatively assess the quality and reliability of the IBI model solution. Likewise, the IBI-MFC compares the IBI forecast products with other model solutions by setting up specific intercomparison exercises on overlapping areas at diverse timescales. In this context, NARVAL web tool already includes a specific module to evaluate strengths and weaknesses of IBI versus other CMEMS operational ocean forecasting systems (OOFSs). In particular, the IBI physical ocean solution is compared against the CMEMS MED and NWS OOFSs. These CMEMS regional services delivered for the Mediterranean and the North West Shelves include data assimilation schemes in their respective operational chains and generate analogous ocean forecast products to the IBI ones. A number of physical parameters (i.e. sea surface temperature, salinity and current velocities) are evaluated through NARVAL on a daily basis in the overlapping areas existing between these three regional systems. NARVAL is currently being updated in order to extend this intercomparison of ocean model parameters to the biogeochemical solutions provided by the aforementioned OOFSs. More specifically, the simulated chlorophyll concentration is evaluated over several subregions of particular concern by using as benchmark the CMEMS satellite-derived observational products. In addition to this IBI comparison against other regional CMEMS products on overlapping areas, a specific intercomparison between the CMEMS GLOBAL solution and the IBI (regional application dynamically embedded in the former) is conducted in order to check its consistency and ability to outperform the parent model solution. Particular emphasis is placed on the comparison of time-series at specified locations (class-2 metrics). The standardized validation methodology presented here is particularly useful and could encompass the intercomparison of the regional application (IBI) and other nested higher resolution models at coastal/shelf scales to quantify the added value of downscaling in local downstream approaches.

Instrument for Measuring Thermal Conductivity of Materials at Low Temperatures

NASA Technical Reports Server (NTRS)

Fesmire, James; Sass, Jared; Johnson, Wesley

2010-01-01

With the advance of polymer and other non-metallic material sciences, whole new series of polymeric materials and composites are being created. These materials are being optimized for many different applications including cryogenic and low-temperature industrial processes. Engineers need these data to perform detailed system designs and enable new design possibilities for improved control, reliability, and efficiency in specific applications. One main area of interest is cryogenic structural elements and fluid handling components and other parts, films, and coatings for low-temperature application. An important thermal property of these new materials is the apparent thermal conductivity (k-value).

Photovoltaic test and demonstration project. [residential energy program

NASA Technical Reports Server (NTRS)

Forestieri, A. F.; Brandhorst, H. W., Jr.; Deyo, J. N.

1976-01-01

The considered project consists of three subprojects related to applications, device performance and diagnostics, and endurance testing. The objectives of the applications subproject include the determination of the operating characteristics for a variety of photovoltaic conversion systems. A system test facility is being constructed in this connection and a prototype residence experiment is to be conducted. Market demand for solar cells is to be stimulated by demonstrating suitability of solar cells for specific near-term applications. Activities conducted in connection with device performance studies and diagnostics are also discussed along with developments in the area of endurance testing.

Nanoporous Gold: Fabrication, Characterization, and Applications

PubMed Central

Seker, Erkin; Reed, Michael L.; Begley, Matthew R.

2009-01-01

Nanoporous gold (np-Au) has intriguing material properties that offer potential benefits for many applications due to its high specific surface area, well-characterized thiol-gold surface chemistry, high electrical conductivity, and reduced stiffness. The research on np-Au has taken place on various fronts, including advanced microfabrication and characterization techniques to probe unusual nanoscale properties and applications spanning from fuel cells to electrochemical sensors. Here, we provide a review of the recent advances in np-Au research, with special emphasis on microfabrication and characterization techniques. We conclude the paper with a brief outline of challenges to overcome in the study of nanoporous metals.

The solar textile challenge: how it will not work and where it might.

PubMed

Krebs, Frederik C; Hösel, Markus

2015-03-01

Solar textiles are highlighted as a future technology with transformative power within the fields of both textiles and solar cells provided that developments are made in critical areas. Specifically, these are fundamental solutions to materials and material combinations with mechanical stability and flexibility imposed by textile architectures, scientific solutions to achieve high carrier transport efficiency and optical transmission in a textile topology, technical solutions to controlling the physical disposition of the anode and cathode along with their specific and error-free contacting and, finally, practical solutions to fast and efficient manufacture and integration. The areas of application and the penetration of solar textiles into our everyday life are expected to be explosive pending efficient developments within these four key areas. A shortcoming in one or more of these will, however, lead to the solar textiles being banned to academic existence. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Three-Dimensional Porous Particles Composed of Curved, Two-Dimensional, Nano-Sized Layers for Li-Ion Batteries

NASA Technical Reports Server (NTRS)

Yushin, Gleb; Evanoff, Kara; Magasinski, Alexander

2012-01-01

Thin Si films coated on porous 3D particles composed of curved 2D graphene sheets have been synthesized utilizing techniques that allow for tunable properties. Since graphene exhibits specific surface area up to 100 times higher than carbon black or graphite, the deposition of the same mass of Si on graphene is much faster in comparison -- a factor which is important for practical applications. In addition, the distance between graphene layers is tunable and variation in the thickness of the deposited Si film is feasible. Both of these characteristics allow for optimization of the energy and power characteristics. Thicker films will allow higher capacity, but slower rate capabilities. Thinner films will allow more rapid charging, or higher power performance. In this innovation, uniform deposition of Si and C layers on high-surface area graphene produced granules with specific surface area (SSA) of 5 sq. m/g.

Dynamic laser speckle technique as an alternative tool to determine hygroscopic capacity and specific surface area of microporous zeolites

NASA Astrophysics Data System (ADS)

Mojica-Sepulveda, Ruth Dary; Mendoza-Herrera, Luís Joaquín; Grumel, Eduardo; Soria, Delia Beatriz; Cabello, Carmen Inés; Trivi, Marcelo

2018-07-01

Adsorption phenomena have several technological applications such as desiccants, catalysts, and separation of gases. Their uses depend on the textural properties of the solid adsorbent and the type of the adsorbed liquid or gas. Therefore, it is important to determine these properties. The most common measurement methods are physicochemical based on adsorption of N2 to determine the surface area and the distribution of pores size. However these techniques present certain limitations for microporous materials. In this paper we propose the use of the Dynamic Laser Speckle (DLS) technique to measure the hygroscopic capacity of a microporous natural zeolite and their modified forms. This new approach based on the adsorption of water by solids allows determine their specific surface area (S). To test the DLS results, we compared the obtained S values to those calculated by different conventional isotherms using the N2 adsorption-desorption method.

Self-Assembled Three-Dimensional Graphene Macrostructures: Synthesis and Applications in Supercapacitors.

PubMed

Xu, Yuxi; Shi, Gaoquan; Duan, Xiangfeng

2015-06-16

Graphene and its derivatives are versatile building blocks for bottom-up assembly of advanced functional materials. In particular, with exceptionally large specific surface area, excellent electrical conductivity, and superior chemical/electrochemical stability, graphene represents the ideal material for various electrochemical energy storage devices including supercapacitors. However, due to the strong π-π interaction between graphene sheets, the graphene flakes tend to restack to form graphite-like powders when they are processed into practical electrode materials, which can greatly reduce the specific surface area and lead to inefficient utilization of the graphene layers for electrochemical energy storage. The self-assembly of two-dimensional graphene sheets into three-dimensional (3D) framework structures can largely retain the unique properties of individual graphene sheets and has recently garnered intense interest for fundamental investigations and potential applications in diverse technologies. In this Account, we review the recent advances in preparing 3D graphene macrostructures and exploring them as a unique platform for supercapacitor applications. We first describe the synthetic strategies, in which reduction of a graphene oxide dispersion above a certain critical concentration can induce the reduced graphene oxide sheets to cross-link with each other via partial π-π stacking interactions to form a 3D interconnected porous macrostructure. Multiple reduction strategies, including hydrothermal/solvothermal reduction, chemical reduction, and electrochemical reduction, have been developed for the preparation of 3D graphene macrostructures. The versatile synthetic strategies allow for easy incorporation of heteroatoms, carbon nanomaterials, functional polymers, and inorganic nanostructures into the macrostructures to yield diverse composites with tailored structures and properties. We then summarize the applications of the 3D graphene macrostructures for high-performance supercapacitors. With a unique framework structure in which the graphene sheets are interlocked in 3D space to prevent their restacking, the graphene macrostructures feature very high specific surface areas, rapid electron and ion transport, and superior mechanical strength. They can thus be directly used as supercapacitor electrodes with excellent specific capacitances, rate capabilities, and cycling stabilities. We finally discuss the current challenges and future opportunities in this research field. By regarding the graphene as both a single-atom-thick carbon sheet and a conjugated macromolecule, our work opens a new avenue to bottom-up self-assembly of graphene macromolecule sheets into functional 3D graphene macrostructures with remarkable electrochemical performances. We hope that this Account will promote further efforts toward fundamental investigation of graphene self-assembly and the development of advanced 3D graphene materials for their real-world applications in electrochemical energy storage devices and beyond.

NIST biometric evaluations and developments

NASA Astrophysics Data System (ADS)

Garris, Michael D.; Wilson, Charles L.

2005-05-01

This paper presents an R&D framework used by the National Institute of Standards and Technology (NIST) for biometric technology testing and evaluation. The focus of this paper is on fingerprint-based verification and identification. Since 9-11 the NIST Image Group has been mandated by Congress to run a program for biometric technology assessment and biometric systems certification. Four essential areas of activity are discussed: 1) developing test datasets, 2) conducting performance assessment; 3) technology development; and 4) standards participation. A description of activities and accomplishments are provided for each of these areas. In the process, methods of performance testing are described and results from specific biometric technology evaluations are presented. This framework is anticipated to have broad applicability to other technology and application domains.

The role of NASA's Water Resources applications area in improving access to water quality-related information and water resources management

NASA Astrophysics Data System (ADS)

Lee, C. M.

2016-02-01

The NASA Applied Sciences Program plays a unique role in facilitating access to remote sensing-based water information derived from US federal assets towards the goal of improving science and evidence-based decision-making in water resources management. The Water Resources Application Area within NASA Applied Sciences works specifically to develop and improve water data products to support improved management of water resources, with partners who are faced with real-world constraints and conditions including cost and regulatory standards. This poster will highlight the efforts and collaborations enabled by this program that have resulted in integration of remote sensing-based information for water quality modeling and monitoring within an operational context.

The role of NASA's Water Resources applications area in improving access to water quality-related information and water resources management

NASA Astrophysics Data System (ADS)

Lee, C. M.

2016-12-01

The NASA Applied Sciences Program plays a unique role in facilitating access to remote sensing-based water information derived from US federal assets towards the goal of improving science and evidence-based decision-making in water resources management. The Water Resources Application Area within NASA Applied Sciences works specifically to develop and improve water data products to support improved management of water resources, with partners who are faced with real-world constraints and conditions including cost and regulatory standards. This poster will highlight the efforts and collaborations enabled by this program that have resulted in integration of remote sensing-based information for water quality modeling and monitoring within an operational context.

Engineering works and the tidal Chesapeake

NASA Technical Reports Server (NTRS)

Hargis, W. J., Jr.

1972-01-01

The tidal tributaries of the ocean and coastal areas of the mid-Atlantic region and the ecological significance of engineering projects are discussed. The effects of engineering works on maritime environments and resources, with the Chesapeake Bay as the area of prime interest are examined. Significant engineering projects, both actual and proposed, are described. The conflict of navigational demands and maintenance of an estuarine environment for commercial and sport fishing and recreation is described. Specific applications of remote sensors for analyzing ecological conditions of the bay are included.

Study on application of aerospace technology to improve surgical implants

NASA Technical Reports Server (NTRS)

Johnson, R. E.; Youngblood, J. L.

1982-01-01

The areas where aerospace technology could be used to improve the reliability and performance of metallic, orthopedic implants was assessed. Specifically, comparisons were made of material controls, design approaches, analytical methods and inspection approaches being used in the implant industry with hardware for the aerospace industries. Several areas for possible improvement were noted such as increased use of finite element stress analysis and fracture control programs on devices where the needs exist for maximum reliability and high structural performance.

Wafer-scale pixelated detector system

DOEpatents

Fahim, Farah; Deptuch, Grzegorz; Zimmerman, Tom

2017-10-17

A large area, gapless, detection system comprises at least one sensor; an interposer operably connected to the at least one sensor; and at least one application specific integrated circuit operably connected to the sensor via the interposer wherein the detection system provides high dynamic range while maintaining small pixel area and low power dissipation. Thereby the invention provides methods and systems for a wafer-scale gapless and seamless detector systems with small pixels, which have both high dynamic range and low power dissipation.

Reducing microbial contamination in storm runoff from high use areas on California coastal dairies.

PubMed

Lewis, D J; Atwill, E R; Lennox, M S; Pereira, M D G; Miller, W A; Conrad, P A; Tate, K W

2009-01-01

High use areas are a fundamental part of California coastal dairies and grazing livestock ranches as feeding areas, nurseries, and sick pens. High stocking densities and daily use in these areas lead to soil surfaces devoid of vegetation and covered in manure, with high potential for manure transport during winter rains to receiving waters regulated for shellfish harvesting and recreation. We characterized the association between California's Mediterranean climate and a series of existing and proposed management practices on fecal coliform bacteria (FCB) transport from high use areas on dairies and ranches. Results from 351 storm runoff samples collected below 35 high-use areas indicate that removal of cattle during winter, locating high use areas on level ground, application of straw and seeding, and vegetative buffer strip implementation were significantly associated with FCB concentration and load reductions. These results complement our findings for reductions of specific pathogens in runoff from these areas. These findings have practical significance because they document surface water quality benefits that the studied management practices provide in application on working farms and ranches. This direction is critical and timely for on-farm management efforts seeking to reduce microbial pollution in runoff and comply with indicator bacteria water quality criteria.

Validation of temporal and spatial consistency of facility- and speed-specific vehicle-specific power distributions for emission estimation: A case study in Beijing, China.

PubMed

Zhai, Zhiqiang; Song, Guohua; Lu, Hongyu; He, Weinan; Yu, Lei

2017-09-01

Vehicle-specific power (VSP) has been found to be highly correlated with vehicle emissions. It is used in many studies on emission modeling such as the MOVES (Motor Vehicle Emissions Simulator) model. The existing studies develop specific VSP distributions (or OpMode distribution in MOVES) for different road types and various average speeds to represent the vehicle operating modes on road. However, it is still not clear if the facility- and speed-specific VSP distributions are consistent temporally and spatially. For instance, is it necessary to update periodically the database of the VSP distributions in the emission model? Are the VSP distributions developed in the city central business district (CBD) area applicable to its suburb area? In this context, this study examined the temporal and spatial consistency of the facility- and speed-specific VSP distributions in Beijing. The VSP distributions in different years and in different areas are developed, based on real-world vehicle activity data. The root mean square error (RMSE) is employed to quantify the difference between the VSP distributions. The maximum differences of the VSP distributions between different years and between different areas are approximately 20% of that between different road types. The analysis of the carbon dioxide (CO 2 ) emission factor indicates that the temporal and spatial differences of the VSP distributions have no significant impact on vehicle emission estimation, with relative error of less than 3%. The temporal and spatial differences have no significant impact on the development of the facility- and speed-specific VSP distributions for the vehicle emission estimation. The database of the specific VSP distributions in the VSP-based emission models can maintain in terms of time. Thus, it is unnecessary to update the database regularly, and it is reliable to use the history vehicle activity data to forecast the emissions in the future. In one city, the areas with less data can still develop accurate VSP distributions based on better data from other areas.

Test systems in drug discovery for hazard identification and risk assessment of human drug-induced liver injury.

PubMed

Weaver, Richard J; Betts, Catherine; Blomme, Eric A G; Gerets, Helga H J; Gjervig Jensen, Klaus; Hewitt, Philip G; Juhila, Satu; Labbe, Gilles; Liguori, Michael J; Mesens, Natalie; Ogese, Monday O; Persson, Mikael; Snoeys, Jan; Stevens, James L; Walker, Tracy; Park, B Kevin

2017-07-01

The liver is an important target for drug-induced toxicities. Early detection of hepatotoxic drugs requires use of well-characterized test systems, yet current knowledge, gaps and limitations of tests employed remains an important issue for drug development. Areas Covered: The current state of the science, understanding and application of test systems in use for the detection of drug-induced cytotoxicity, mitochondrial toxicity, cholestasis and inflammation is summarized. The test systems highlighted herein cover mostly in vitro and some in vivo models and endpoint measurements used in the assessment of small molecule toxic liabilities. Opportunities for research efforts in areas necessitating the development of specific tests and improved mechanistic understanding are highlighted. Expert Opinion: Use of in vitro test systems for safety optimization will remain a core activity in drug discovery. Substantial inroads have been made with a number of assays established for human Drug-induced Liver Injury. There nevertheless remain significant gaps with a need for improved in vitro tools and novel tests to address specific mechanisms of human Drug-Induced Liver Injury. Progress in these areas will necessitate not only models fit for application, but also mechanistic understanding of how chemical insult on the liver occurs in order to identify translational and quantifiable readouts for decision-making.

Fabrication of single/multi-walled hybrid buckypaper composites and their enhancement of electromagnetic interference shielding performance

NASA Astrophysics Data System (ADS)

Lu, Shaowei; Shao, Junyan; Ma, Keming; Wang, Xiaoqiang; Zhang, Lu; Meng, Qingshi

2016-11-01

Multi-walled carbon nanotubes and single-walled carbon nanotubes show great potential for the application as an electromagnetic interference shielding material. In this paper, the electromagnetic interference shielding the effectiveness of a composite surface coated single/multi-walled carbon nanotube hybrid buckypaper was measured, which showed an average shielding effectiveness of ~55 dB with a buckypaper thickness of 50 µm, and bukypaper density of 0.76 g cm-3, it is much higher than other carbon nanotube/resin materials when sample thickness is on the similar order. The structural, specific surface area and conductivity of the buckypapers were examined by field-emission scanning electron microscopy, specific surface area analyzer and four probes resistance tester, respectively.

Heteroditopic receptors for ion-pair recognition.

PubMed

McConnell, Anna J; Beer, Paul D

2012-05-21

Ion-pair recognition is a new field of research emerging from cation and anion coordination chemistry. Specific types of heteroditopic receptor designs for ion pairs and the complexity of ion-pair binding are discussed to illustrate key concepts such as cooperativity. The importance of this area of research is reflected by the wide variety of potential applications of ion-pair receptors, including applications as membrane transport and salt solubilization agents and sensors. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Combining real-time monitoring and knowledge-based analysis in MARVEL

NASA Technical Reports Server (NTRS)

Schwuttke, Ursula M.; Quan, A. G.; Angelino, R.; Veregge, J. R.

1993-01-01

Real-time artificial intelligence is gaining increasing attention for applications in which conventional software methods are unable to meet technology needs. One such application area is the monitoring and analysis of complex systems. MARVEL, a distributed monitoring and analysis tool with multiple expert systems, was developed and successfully applied to the automation of interplanetary spacecraft operations at NASA's Jet Propulsion Laboratory. MARVEL implementation and verification approaches, the MARVEL architecture, and the specific benefits that were realized by using MARVEL in operations are described.

Chiral phosphoric acid catalysis: from numbers to insights.

PubMed

Maji, Rajat; Mallojjala, Sharath Chandra; Wheeler, Steven E

2018-02-19

Chiral phosphoric acids (CPAs) have emerged as powerful organocatalysts for asymmetric reactions, and applications of computational quantum chemistry have revealed important insights into the activity and selectivity of these catalysts. In this tutorial review, we provide an overview of computational tools at the disposal of computational organic chemists and demonstrate their application to a wide array of CPA catalysed reactions. Predictive models of the stereochemical outcome of these reactions are discussed along with specific examples of representative reactions and an outlook on remaining challenges in this area.

Preparation Methods of Metal Organic Frameworks and Their Capture of CO2

NASA Astrophysics Data System (ADS)

Zhang, Linjian; Liand, Fangqin; Luo, Liangfei

2018-01-01

The increasingly serious greenhouse effect makes people pay more attention to the capture and storage technology of CO2. Metal organic frameworks (MOFs) have the advantages of high specific surface area, porous structure and controllable structure, and become the research focus of CO2 emission reduction technology in recent years. In this paper, the characteristics, preparation methods and application of MOFs in the field of CO2 adsorption and separation are discussed, especially the application of flue gas environment in power plants.

Study of multiple cycles valves

NASA Technical Reports Server (NTRS)

Wichmann, H.

1973-01-01

A discussion is presented regarding valves which can be cycled repeatedly and are available from industry for application in the inlet system for the Pioneer Venus Probe mass spectrometer. Both solenoid type and latching type valves are considered. The study is divided into two principal areas: (1) preparation of a valve specification reflecting the requirements of the inlet system cyclic valves for the Pioneer Venus Probe mass spectrometer and the submittal of this specification to potential valve suppliers for their response and proposal; (2) preparation of a design layout of an optimum cyclic valve meeting all of the valve specification requirements.

Estrone specific molecularly imprinted polymeric nanospheres: synthesis, characterization and applications for electrochemical sensor development.

PubMed

Congur, Gulsah; Senay, Hilal; Turkcan, Ceren; Canavar, Ece; Erdem, Arzum; Akgol, Sinan

2013-06-28

The aim of this study is (i) to prepare estrone-imprinted nanospheres (nano-EST-MIPs) and (ii) to integrate them into the electrochemical sensor as a recognition layer. N-methacryloyl-(l)-phenylalanine (MAPA) was chosen as the complexing monomer. Firstly, estrone (EST) was complexed with MAPA and the EST-imprinted poly(2-hyroxyethylmethacrylate-co-N-methacryloyl-(l)-phenylalanine) [EST-imprinted poly(HEMA-MAPA)] nanospheres were synthesized by surfactant- free emulsion polymerization method. The specific surface area of the EST-imprinted poly(HEMA-MAPA) nanospheres was found to be 1275 m2/g with a size of 163.2 nm in diameter. According to the elemental analysis results, the nanospheres contained 95.3 mmole MAPA/g nanosphere. The application of EST specific MIP nanospheres for the development of an electrochemical biosensor was introduced for the first time in our study by using electrochemical impedance spectroscopy (EIS) technique. This nano-MIP based sensor presented a great specificity and selectivity for EST.

Evaluating wilderness recreational opportunities: application of an impact matrix

USGS Publications Warehouse

Stohlgren, Thomas J.; Parsons, David J.

1992-01-01

An inventory of the severity and spatial distribution of wilderness campsite impacts in Sequoia and Kings Canyon National Parks identified a total of 273 distinct nodes of campsites or “management areas.” A campsite impact matrix was developed to evaluate management areas based on total impacts (correlated to the total area of campsite development) and the density, or concentration, of impacts relative to each area's potentially campable area. The matrix is used to quantify potential recreational opportunities for wilderness visitors in a spectrum from areas offering low impact-dispersed camping to those areas offering high impact-concentrated camping. Wilderness managers can use this type of information to evaluate use distribution patterns, identify areas to increase or decrease use, and to identify areas needing site-specific regulations (e.g., one-night camping limits) to preserve wilderness resources and guarantee outstanding opportunities for solitude.

Space Applications of Automation, Robotics and Machine Intelligence Systems (ARAMIS). Volume 4: Supplement, Appendix 4.3: Candidate ARAMIS Capabilities

NASA Technical Reports Server (NTRS)

Miller, R. H.; Minsky, M. L.; Smith, D. B. S.

1982-01-01

Potential applications of automation, robotics, and machine intelligence systems (ARAMIS) to space activities, and to their related ground support functions, in the years 1985-2000, so that NASA may make informed decisions on which aspects of ARAMIS to develop. The study first identifies the specific tasks which will be required by future space projects. It then defines ARAMIS options which are candidates for those space project tasks, and evaluates the relative merits of these options. Finally, the study identifies promising applications of ARAMIS, and recommends specific areas for further research. The ARAMIS options defined and researched by the study group span the range from fully human to fully machine, including a number of intermediate options (e.g., humans assisted by computers, and various levels of teleoperation). By including this spectrum, the study searches for the optimum mix of humans and machines for space project tasks.

Fabrication technologies and sensing applications of graphene-based composite films: Advances and challenges.

PubMed

Yu, Xiaoqing; Zhang, Wensi; Zhang, Panpan; Su, Zhiqiang

2017-03-15

Graphene (G)-based composite materials have been widely explored for the sensing applications ascribing to their atom-thick two-dimensional conjugated structures, high conductivity, large specific surface areas and controlled modification. With the enormous advantages of film structure, G-based composite films (GCFs), prepared by combining G with different functional nanomaterials (noble metals, metal compounds, carbon materials, polymer materials, etc.), show unique optical, mechanical, electrical, chemical, and catalytic properties. Therefore, great quantities of sensors with high sensitivity, selectivity, and stability have been created in recent years. In this review, we focus on the recent advances in the fabrication technologies of GCFs and their specific sensing applications. In addition, the relationship between the properties of GCFs and sensing performance is concentrated on. Finally, the personal perspectives and key challenges of GCFs are mentioned in the hope to shed a light on their potential future research directions. Copyright © 2016 Elsevier B.V. All rights reserved.

Micro-channel-based high specific power lithium target

NASA Astrophysics Data System (ADS)

Mastinu, P.; Martın-Hernández, G.; Praena, J.; Gramegna, F.; Prete, G.; Agostini, P.; Aiello, A.; Phoenix, B.

2016-11-01

A micro-channel-based heat sink has been produced and tested. The device has been developed to be used as a Lithium target for the LENOS (Legnaro Neutron Source) facility and for the production of radioisotope. Nevertheless, applications of such device can span on many areas: cooling of electronic devices, diode laser array, automotive applications etc. The target has been tested using a proton beam of 2.8MeV energy and delivering total power shots from 100W to 1500W with beam spots varying from 5mm2 to 19mm2. Since the target has been designed to be used with a thin deposit of lithium and since lithium is a low-melting-point material, we have measured that, for such application, a specific power of about 3kW/cm2 can be delivered to the target, keeping the maximum surface temperature not exceeding 150° C.

Nanocarriers in therapy of infectious and inflammatory diseases

NASA Astrophysics Data System (ADS)

Ikoba, Ufuoma; Peng, Haisheng; Li, Haichun; Miller, Cathy; Yu, Chenxu; Wang, Qun

2015-02-01

Nanotechnology is a growing science that has applications in various areas of medicine. The composition of nanocarriers for drug delivery is critical to guarantee high therapeutic performance when targeting specific host sites. Applications of nanotechnology are prevalent in the diagnosis and treatment of infectious and inflammatory diseases. This review summarizes recent advancements in the application of nanotechnology to the therapy of infectious and inflammatory diseases. The major focus is on the design and fabrication of various nanomaterials, characteristics and physicochemical properties of drug-loaded nanocarriers, and the use of these nanoscale drug delivery systems in treating infectious and inflammatory diseases, such as AIDS, hepatitis, tuberculosis, melanoma, and representative inflammatory diseases. Clinical trials and future perspective of the use of nanocarriers are also discussed in detail. We hope that such a review will be valuable to researchers who are exploring nanoscale drug delivery systems for the treatment of specific infectious and inflammatory diseases.

High-surface-area nitrogen-doped reduced graphene oxide for electric double-layer capacitors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Youn, Hee-Chang; Bak, Seong-Min; Kim, Myeong-Seong

A two-step method consisting of solid-state microwave irradiation and heat treatment under NH₃ gas was used to prepare nitrogen-doped reduced graphene oxide (N-RGO) with a high specific surface area (1007m²g⁻¹), high electrical conductivity (1532S m⁻¹), and low oxygen content (1.5 wt%) for electric double-layer capacitor applications. The specific capacitance of N-RGO was 291 Fg⁻¹ at a current density of 1 A g⁻¹, and a capacitance of 261 F g⁻¹ was retained at 50 A g⁻¹, indicating a very good rate capability. N-RGO also showed excellent cycling stability, preserving 96% of the initial specific capacitance after 100,000 cycles. Near-edge X-ray absorptionmore » fine-structure spectroscopy evidenced the recover of π-conjugation in the carbon networks with the removal of oxygenated groups and revealed the chemical bonding of the nitrogen atoms in N-RGO. The good electrochemical performance of N-RGO is attributed to its high surface area, high electrical conductivity, and low oxygen content.« less

High-surface-area nitrogen-doped reduced graphene oxide for electric double-layer capacitors

DOE PAGES

Youn, Hee-Chang; Bak, Seong-Min; Kim, Myeong-Seong; ...

2015-06-08

A two-step method consisting of solid-state microwave irradiation and heat treatment under NH₃ gas was used to prepare nitrogen-doped reduced graphene oxide (N-RGO) with a high specific surface area (1007m²g⁻¹), high electrical conductivity (1532S m⁻¹), and low oxygen content (1.5 wt%) for electric double-layer capacitor applications. The specific capacitance of N-RGO was 291 Fg⁻¹ at a current density of 1 A g⁻¹, and a capacitance of 261 F g⁻¹ was retained at 50 A g⁻¹, indicating a very good rate capability. N-RGO also showed excellent cycling stability, preserving 96% of the initial specific capacitance after 100,000 cycles. Near-edge X-ray absorptionmore » fine-structure spectroscopy evidenced the recover of π-conjugation in the carbon networks with the removal of oxygenated groups and revealed the chemical bonding of the nitrogen atoms in N-RGO. The good electrochemical performance of N-RGO is attributed to its high surface area, high electrical conductivity, and low oxygen content.« less

Mining textural knowledge in biological images: Applications, methods and trends.

PubMed

Di Cataldo, Santa; Ficarra, Elisa

2017-01-01

Texture analysis is a major task in many areas of computer vision and pattern recognition, including biological imaging. Indeed, visual textures can be exploited to distinguish specific tissues or cells in a biological sample, to highlight chemical reactions between molecules, as well as to detect subcellular patterns that can be evidence of certain pathologies. This makes automated texture analysis fundamental in many applications of biomedicine, such as the accurate detection and grading of multiple types of cancer, the differential diagnosis of autoimmune diseases, or the study of physiological processes. Due to their specific characteristics and challenges, the design of texture analysis systems for biological images has attracted ever-growing attention in the last few years. In this paper, we perform a critical review of this important topic. First, we provide a general definition of texture analysis and discuss its role in the context of bioimaging, with examples of applications from the recent literature. Then, we review the main approaches to automated texture analysis, with special attention to the methods of feature extraction and encoding that can be successfully applied to microscopy images of cells or tissues. Our aim is to provide an overview of the state of the art, as well as a glimpse into the latest and future trends of research in this area.

The status and future of acupuncture mechanism research.

PubMed

Napadow, Vitaly; Ahn, Andrew; Longhurst, John; Lao, Lixing; Stener-Victorin, Elisabet; Harris, Richard; Langevin, Helene M

2008-09-01

On November 8-9, 2007, the Society for Acupuncture Research (SAR) hosted an international conference to mark the tenth anniversary of the landmark NIH [National Institutes of Health] Consensus Development Conference on Acupuncture. More than 300 acupuncture researchers, practitioners, students, funding agency personnel, and health policy analysts from 20 countries attended the SAR meeting held at the University of Maryland School of Medicine, Baltimore, MD. This paper summarizes important invited lectures in the area of basic and translational acupuncture research. Specific areas include the scientific assessment of acupuncture points and meridians, the neural mechanisms of cardiovascular regulation by acupuncture, mechanisms for electroacupuncture applied to persistent inflammation and pain, basic and translational research on acupuncture in gynecologic applications, the application of functional neuroimaging to acupuncture research with specific application to carpal-tunnel syndrome and fibromyalgia, and the association of the connective tissue system to acupuncture research. In summary, mechanistic models for acupuncture effects that have been investigated experimentally have focused on the effects of acupuncture needle stimulation on the nervous system, muscles, and connective tissue. These mechanistic models are not mutually exclusive. Iterative testing, expanding, and perhaps merging of such models will potentially lead to an incremental understanding of the effects of manual and electrical stimulation of acupuncture needles that is solidly rooted in physiology.

Electron-beam Induced Processes and their Applicability to Mask Repair

NASA Astrophysics Data System (ADS)

Boegli, Volker A.; Koops, Hans W. P.; Budach, Michael; Edinger, Klaus; Hoinkis, Ottmar; Weyrauch, Bernd; Becker, Rainer; Schmidt, Rudolf; Kaya, Alexander; Reinhardt, Andreas; Braeuer, Stephan; Honold, Heinz; Bihr, Johannes; Greiser, Jens; Eisenmann, Michael

2002-12-01

The applicability of electron-beam induced chemical reactions to mask repair is investigated. To achieve deposition and chemical etching with a focused electron-beam system, it is required to disperse chemicals in a molecular beam to the area of interest with a well-defined amount of molecules and monolayers per second. For repair of opaque defects the precursor gas reacts with the absorber material of the mask and forms a volatile reaction product, which leaves the surface. In this way the surface atoms are removed layer by layer. For clear defect repair, additional material, which is light absorbing in the UV, is deposited onto the defect area. This material is rendered as a nanocrystalline deposit from metal containing precursors. An experimental electron-beam mask repair system is developed and used to perform exploratory work applicable to photo mask, EUV mask, EPL and LEEPL stencil mask repair. The tool is described and specific repair actions are demonstrated. Platinum deposited features with lateral dimensions down to 20 nm demonstrate the high resolution obtainable with electron beam induced processes, while AFM and AIMS measurements indicate, that specifications for mask repair at the 70 nm device node can be met. In addition, examples of etching quartz and TaN are given.

Extraction of Built-Up Areas Using Convolutional Neural Networks and Transfer Learning from SENTINEL-2 Satellite Images

NASA Astrophysics Data System (ADS)

Bramhe, V. S.; Ghosh, S. K.; Garg, P. K.

2018-04-01

With rapid globalization, the extent of built-up areas is continuously increasing. Extraction of features for classifying built-up areas that are more robust and abstract is a leading research topic from past many years. Although, various studies have been carried out where spatial information along with spectral features has been utilized to enhance the accuracy of classification. Still, these feature extraction techniques require a large number of user-specific parameters and generally application specific. On the other hand, recently introduced Deep Learning (DL) techniques requires less number of parameters to represent more abstract aspects of the data without any manual effort. Since, it is difficult to acquire high-resolution datasets for applications that require large scale monitoring of areas. Therefore, in this study Sentinel-2 image has been used for built-up areas extraction. In this work, pre-trained Convolutional Neural Networks (ConvNets) i.e. Inception v3 and VGGNet are employed for transfer learning. Since these networks are trained on generic images of ImageNet dataset which are having very different characteristics from satellite images. Therefore, weights of networks are fine-tuned using data derived from Sentinel-2 images. To compare the accuracies with existing shallow networks, two state of art classifiers i.e. Gaussian Support Vector Machine (SVM) and Back-Propagation Neural Network (BP-NN) are also implemented. Both SVM and BP-NN gives 84.31 % and 82.86 % overall accuracies respectively. Inception-v3 and VGGNet gives 89.43 % of overall accuracy using fine-tuned VGGNet and 92.10 % when using Inception-v3. The results indicate high accuracy of proposed fine-tuned ConvNets on a 4-channel Sentinel-2 dataset for built-up area extraction.

Cobalt silicate hierarchical hollow spheres for lithium-ion batteries.

PubMed

Yang, Jun; Guo, Yuanyuan; Zhang, Yufei; Sun, Chencheng; Yan, Qingyu; Dong, Xiaochen

2016-09-09

In this paper, the synthesis of cobalt silicate novel hierarchical hollow spheres via a facile hydrothermal method is presented. With a unique hollow structure, the Co2SiO4 provides a large surface area, which can shorten the lithium ions diffusion length and effectively accommodate the volumetic variation during the lithiation/de-lithiation process. Serving as an anode material in lithium-ion battery application, the Co2SiO4 electrode demonstrates a high reversible specific capacity (first-cycle charge capacity of 948.6 mAh g(-1) at 100 mA g(-1)), a cycling durability (specific capacity of 791.4 mAh g(-1) after 100 cycles at 100 mA g(-1)), and a good rate capability (specific capacity of 349.4 mAh g(-1) at 10 A g(-1)). The results indicate that the cobalt silicate hierarchical hollow sphere holds the potential applications in energy storage electrodes.

A human factors methodology for real-time support applications

NASA Technical Reports Server (NTRS)

Murphy, E. D.; Vanbalen, P. M.; Mitchell, C. M.

1983-01-01

A general approach to the human factors (HF) analysis of new or existing projects at NASA/Goddard is delineated. Because the methodology evolved from HF evaluations of the Mission Planning Terminal (MPT) and the Earth Radiation Budget Satellite Mission Operations Room (ERBS MOR), it is directed specifically to the HF analysis of real-time support applications. Major topics included for discussion are the process of establishing a working relationship between the Human Factors Group (HFG) and the project, orientation of HF analysts to the project, human factors analysis and review, and coordination with major cycles of system development. Sub-topics include specific areas for analysis and appropriate HF tools. Management support functions are outlined. References provide a guide to sources of further information.

An application specific integrated circuit based multi-anode microchannel array readout system

NASA Technical Reports Server (NTRS)

Smeins, Larry G.; Stechman, John M.; Cole, Edward H.

1991-01-01

Size reduction of two new multi-anode microchannel array (MAMA) readout systems is described. The systems are based on two analog and one digital application specific integrated circuits (ASICs). The new readout systems reduce volume over previous discrete designs by 80 percent while improving electrical performance on virtually every significant parameter. Emphasis is made on the packaging used to achieve the volume reduction. Surface mount technology (SMT) is combined with modular construction for the analog portion of the readout. SMT reliability concerns and the board area impact of MIL SPEC SMT components is addressed. Package selection for the analog ASIC is discussed. Future sytems will require even denser packaging and the volume reduction progression is shown.

Facile Synthesis of Novel Networked Ultralong Cobalt Sulfide Nanotubes and Its Application in Supercapacitors.

PubMed

Liu, Sangui; Mao, Cuiping; Niu, Yubin; Yi, Fenglian; Hou, Junke; Lu, Shiyu; Jiang, Jian; Xu, Maowen; Li, Changming

2015-11-25

Ultralong cobalt sulfide (CoS(1.097)) nanotube networks are synthesized by a simple one-step solvothermal method without any surfactant or template. A possible formation mechanism for the growth processes is proposed. Owing to the hollow structure and large specific area, the novel CoS(1.097) materials present outstanding electrochemical properties. Electrochemical measurements for supercapacitors show that the as-prepared ultralong CoS(1.097) nanotube networks exhibit high specific capacity, good capacity retention, and excellent Coulombic efficiency.

Installation Restoration Program. Phase II. Problem Confirmation and Quantification Study, Griffiss Air Force Base, Rome, New York.

DTIC Science & Technology

1982-12-01

Base 6-26 17 Confirmation Stage Soil PCB Data, Building 112, Griffiss Air Force Base 6-27 18 Analysis of Roof and Oil Samples Building 112, Griffiss...Chlordane Application 46 52 (14) Drywell, Building 219 46 36 (14) PCB Spill at Floyd 46 47 17 Hazardous Waste Storage Area, Lot 69 38 47 18 Waste Oil ...specific anions, oil and grease, pH, and specific conductance. * Prepare a field investigations report delineating the nature and magnitude of

Application of NIR fluorescent markers to quantify expression level of HER2 receptors in carcinomas in vivo

NASA Astrophysics Data System (ADS)

Chernomordik, Victor; Hassan, Moinuddin; Lee, Sang Bong; Zielinski, Rafal; Capala, Jacek; Gandjbakhche, Amir

2010-02-01

HER2 overexpression has been associated with a poor prognosis and resistance to therapy in breast cancer patients. However, quantitative estimates of this important characteristic have been limited to ex vivo ELISA essays of tissue biopsies and/or PET. We develop a novel approach in optical imaging, involving specific probes, not interfering with the binding of the therapeutic agents, thus, excluding competition between therapy and imaging. Affibody-based molecular probes seem to be ideal for in vivo analysis of HER2 receptors using near-infrared optical imaging. Fluorescence intensity distributions, originating from specific markers in the tumor area, can reveal the corresponding fluorophore concentration. We use temporal changes of the signal from a contrast agent, conjugated with HER2-specific Affibody as a signature to monitor in vivo the receptors status in mice with different HER2 over-expressed tumor models. Kinetic model, incorporating saturation of the bound ligands in the tumor area due to HER2 receptor concentration, is suggested to analyze relationship between tumor cell characteristics, i.e., HER2 overexpression, obtained by traditional ("golden standard") ex vivo methods (ELISA), and parameters, estimated from the series of images in vivo. Observed correlation between these parameters and HER2 overexpression substantiates application of our approach to quantify HER2 concentration in vivo.

Study Design to Test the Hypothesis That Long-Term Space Travel Harms the Human and Animal Immune Systems

NASA Technical Reports Server (NTRS)

Shearer, William T.; Lugg, Desmond J.; Ochs, H. D.; Pierson, Duane L.; Reuben, James M.; Rosenblatt, Howard M.; Sams, Clarence; Smith, C. Wayne; Smith, E. Obrian; Smolen, James E.

1999-01-01

The potential threat of immunosuppression and abnormal inflammatory responses in long-term space travel, leading to unusual predilection for opportunistic infections, malignancy, and death, is of ma or concern to the National Aeronautics and Space Administration (NASA) Program. This application has been devised to seek answers to questions of altered immunity in space travel raised by previous investigations spanning 30-plus years. We propose to do this with the help of knowledge gained by the discovery of the molecular basis of many primary and secondary immunodeficiency diseases and by application of molecular and genetic technology not previously available. Two areas of immunity that previously received little attention in space travel research will be emphasized: specific antibody responses and non-specific inflammation and adhesion. Both of these areas of research will not only add to the growing body of information on the potential effects of space travel on the immune system, but be able to delineate any functional alterations in systems important for antigen presentation, specific immune memory, and cell:cell and cell:endothelium interactions. By more precisely defining molecular dysfunction of components of the immune system, it is hoped that targeted methods of prevention of immune damage in space could be devised.

Transfer of aerospace technology to selected public sector areas of concern

NASA Technical Reports Server (NTRS)

Berke, J. G.

1972-01-01

The activities of the NASA Technology Applications Team at Stanford Research Institute, California are discussed. The specific activities in the fields of criminalistics and transportation are reported. The overall objectives of the program are stated on the basis of successful technology transfer and providing appropriate visibility for program activities.

Application of remote sensing

NASA Technical Reports Server (NTRS)

Graff, W. J. (Compiler)

1973-01-01

Remote sensing and aerial photographic interpretation are discussed along with the specific imagery techniques used for this research. The method used to select sites, the results of data analyses for the Houston metropolitan area, and the location of dredging sites along the Houston Ship Channel are presented. The work proposed for the second year of the project is described.

Enhancement of regional wet deposition estimates based on modeled precipitation inputs

Treesearch

James A. Lynch; Jeffery W. Grimm; Edward S. Corbett

1996-01-01

Application of a variety of two-dimensional interpolation algorithms to precipitation chemistry data gathered at scattered monitoring sites for the purpose of estimating precipitation- born ionic inputs for specific points or regions have failed to produce accurate estimates. The accuracy of these estimates is particularly poor in areas of high topographic relief....

Estimating total forest biomass in New York, 1993

Treesearch

Eric Wharton; Carol Alerich; David A. Drake; David A. Drake

1997-01-01

Presents methods for synthesizing information from existing biomass literature for estimating biomass over extensive forest areas with specific applications to New York. Tables of appropriate regression equations and the tree and shrub species to which these equations can be applied are presented well as biomass estimates at the county, geographic unit, and state level...

49 CFR Appendix to Subpart G of... - Required Knowledge and Skills-Sample Guidelines

Code of Federal Regulations, 2010 CFR

2010-10-01

... knowledge and skills tests that it administers to CDL applicants. This appendix closely follows the... discretion provided their CDL program tests for the general areas of knowledge and skill specified in §§ 383.111 and 383.113. Examples of specific knowledge elements (a) Safe operations regulations. Driver...

75 FR 17125 - Foreign-Trade Zone 157-Casper, Wyoming, Application for Expansion

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-05

...): Proposed Site 2 (984 acres) Casper Logistics Hub, located adjacent to and northeast of the airport at 6... Industrial Ranch, LLC and the Casper Logistics Hub. The site will be used to provide logistics, warehousing and distribution services to area businesses. No specific manufacturing authority is being requested...

38 CFR 36.4514 - Eligibility requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

.... (Authority: 38 U.S.C. 501) (d) Private capital is not available in the area at an interest rate not in excess of the rate authorized for guaranteed home loans for a loan for which the veteran is qualified under... and any such covenant is specifically disclaimed; and (3) The applicant understands that civil action...

Evidence Summary for H&R Block College Financial Aid Application Assistance. Top Tier Evidence Initiative

ERIC Educational Resources Information Center

Coalition for Evidence-Based Policy, 2012

2012-01-01

U.S. social programs, set up to address important problems, often fall short by funding specific models/strategies ("interventions") that are not effective. When evaluated in scientifically-rigorous studies, social interventions in K-12 education, job training, crime prevention, and other areas are frequently found ineffective or…

78 FR 47582 - Endangered and Threatened Wildlife and Plants; Endangered Species Status for the Sharpnose Shiner...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-06

... analysis of the best available science and application of that science and to provide any additional... in these areas of science are limited, some uncertainties are associated with this assessment. Where... in the foreseeable future (threatened species). Because of the fact-specific nature of listing...

Advanced Distributed Simulation Technology Advanced Rotary Wing Aircraft. System/Segment Specification. Volume 1. Simulation System Module

DTIC Science & Technology

1994-03-31

overhead water sprinklers in enclosed personnel areas not already protected by existing facility fire suppression systems. Sprinkler systems shall not...facilitate future changes and updates to remain current with the application aircraft. 3.4.4 Availabilit . The ARWA SS shall be designed and constructed to

Foundations that Provide Support for Human Services: A Selected List.

ERIC Educational Resources Information Center

Smith, Bertha, Comp.

Lists of foundations can aid the user in securing funding sources for projects in the areas of health, education, community development and/or social services. The user is cautioned that grantsmanship is a competitive process; grants application procedures vary from one foundation to another. In the absence of any specific guidelines, important…

76 FR 23230 - Segregation of Lands-Renewable Energy

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-26

... within the wind energy right-of- way application areas in FY 2009 and 2010, we estimate the total cost of... transmission facilities that could be used to carry the power generated from a specific wind or solar energy..., public lands included in a pending or future wind or solar energy generation right-of-way (ROW...

40 CFR 434.72 - Effluent limitations attainable by the application of the best practicable control technology...

Code of Federal Regulations, 2010 CFR

2010-07-01

... currently available (BPT). (a) The operator must submit a site-specific Pollution Abatement Plan to the permitting authority for the pollution abatement area. The plan must be approved by the permitting authority and incorporated into the permit as an effluent limitation. The Pollution Abatement Plan must identify...

Nano-Bio Quantum Technology for Device-Specific Materials

NASA Technical Reports Server (NTRS)

Choi, Sang H.

2009-01-01

The areas discussed are still under development: I. Nano structured materials for TE applications a) SiGe and Be.Te; b) Nano particles and nanoshells. II. Quantum technology for optical devices: a) Quantum apertures; b) Smart optical materials; c) Micro spectrometer. III. Bio-template oriented materials: a) Bionanobattery; b) Bio-fuel cells; c) Energetic materials.

Teaching Strategies and Methods in Modern Environments for Learning of Programming

ERIC Educational Resources Information Center

Djenic, Slobodanka; Mitic, Jelena

2017-01-01

This paper presents teaching strategies and methods, applicable in modern blended environments for learning of programming. Given the fact that the manner of applying teaching strategies always depends on the specific requirements of a certain area of learning, the paper outlines the basic principles of teaching in programming courses, as well as…

Expert Systems: Implications for the Diagnosis and Treatment of Learning Disabilities.

ERIC Educational Resources Information Center

Hofmeister, Alan M.; Lubke, Margaret M.

1988-01-01

The article examines characteristics and present or potential applications of expert systems technology for diagnosis and treatment of learning disabilities. Preliminary findings indicate that expert systems can perform as well as humans in specific areas, and that the process of organizing knowledge bases for expert systems helps clarify existing…

Report to Congress on the Indemnification of Contractors Performing Environmental Restoration

DTIC Science & Technology

1993-11-01

munitions dating from World War I. This led true if the contractor is uninsured or has inadequate to the discovery that this residential area had once...application of this authority to the Pab. L. 8545 , 𔄁he National Defemse Contracts Act" specific circumstances of an environmental restoration I contracting

Fluorene-Based Conjugated Microporous Polymers: Preparation and Chemical Sensing Application.

PubMed

Zhang, Qiujing; Yu, Sen; Wang, Qian; Xiao, Qin; Yue, Yong; Ren, Shijie

2017-12-01

Conjugated microporous polymers (CMPs) with strong fluorescence are great candidates for optoelectronic applications such as photocatalysis and chemical sensing. A series of novel fluorene-based conjugated microporous polymers (FCMPs) with different electronic structures are prepared by Yamamoto coupling reactions using rationally designed monomers. The FCMPs show a high degree of microporosity, decent specific surface areas, and variable fluorescence. FCMP3, which possesses a triazine knot in the network, exhibits the highest specific surface area of 489 m 2 g -1 , the largest pore volume of 0.30 cm 3 g -1 , and the highest solid-state photoluminescence quantum yield of 11.46%. Chemical sensing performance of FCMPs is studied using a range of nitroaromatic compounds as the analytes. Among the FCMPs, FCMP3 exhibits the highest Stern-Volmer constants of 2541, 4708, and 5241 m -1 for the detection of nitrobenzene, 4-nitrotoluene, 2,4-dinitrotoluene, respectively, which are comparable to the detecting efficiency of the state-of-the-art CMP-based sensing agents. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Evolution of a Patient Information Management System in a Local Area Network Environment at Loyola University of Chicago Medical Center

PubMed Central

Price, Ronald N; Chandrasekhar, Arcot J; Tamirisa, Balaji

1990-01-01

The Department of Medicine at Loyola University Medical Center (LUMC) of Chicago has implemented a local area network (LAN) based Patient Information Management System (PIMS) as part of its integrated departmental database management system. PIMS consists of related database applications encompassing demographic information, current medications, problem lists, clinical data, prior events, and on-line procedure results. Integration into the existing departmental database system permits PIMS to capture and manipulate data in other departmental applications. Standardization of clinical data is accomplished through three data tables that verify diagnosis codes, procedures codes and a standardized set of clinical data elements. The modularity of the system, coupled with standardized data formats, allowed the development of a Patient Information Protocol System (PIPS). PIPS, a userdefinable protocol processor, provides physicians with individualized data entry or review screens customized for their specific research protocols or practice habits. Physician feedback indicates that the PIMS/PIPS combination enhances their ability to collect and review specific patient information by filtering large amount of clinical data.

Network protocols for real-time applications

NASA Technical Reports Server (NTRS)

Johnson, Marjory J.

1987-01-01

The Fiber Distributed Data Interface (FDDI) and the SAE AE-9B High Speed Ring Bus (HSRB) are emerging standards for high-performance token ring local area networks. FDDI was designed to be a general-purpose high-performance network. HSRB was designed specifically for military real-time applications. A workshop was conducted at NASA Ames Research Center in January, 1987 to compare and contrast these protocols with respect to their ability to support real-time applications. This report summarizes workshop presentations and includes an independent comparison of the two protocols. A conclusion reached at the workshop was that current protocols for the upper layers of the Open Systems Interconnection (OSI) network model are inadequate for real-time applications.

Hypermedia and intelligent tutoring applications in a mission operations environment

NASA Technical Reports Server (NTRS)

Ames, Troy; Baker, Clifford

1990-01-01

Hypermedia, hypertext and Intelligent Tutoring System (ITS) applications to support all phases of mission operations are investigated. The application of hypermedia and ITS technology to improve system performance and safety in supervisory control is described - with an emphasis on modeling operator's intentions in the form of goals, plans, tasks, and actions. Review of hypermedia and ITS technology is presented as may be applied to the tutoring of command and control languages. Hypertext based ITS is developed to train flight operation teams and System Test and Operation Language (STOL). Specific hypermedia and ITS application areas are highlighted, including: computer aided instruction of flight operation teams (STOL ITS) and control center software development tools (CHIMES and STOL Certification Tool).

Microwave Tissue Ablation: Biophysics, Technology and Applications

PubMed Central

2010-01-01

Microwave ablation is an emerging treatment option for many cancers, cardiac arrhythmias and other medical conditions. During treatment, microwaves are applied directly to tissues to produce rapid temperature elevations sufficient to produce immediate coagulative necrosis. The engineering design criteria for each application differ, with individual consideration for factors such as desired ablation zone size, treatment duration, and procedural invasiveness. Recent technological developments in applicator cooling, power control and system optimization for specific applications promise to increase the utilization of microwave ablation in the future. This article will review the basic biophysics of microwave tissue heating, provide an overview of the design and operation of current equipment, and outline areas for future research for microwave ablation. PMID:21175404

Nanotechnology applications in urology: a review.

PubMed

Maddox, Michael; Liu, James; Mandava, Sree Harsha; Callaghan, Cameron; John, Vijay; Lee, Benjamin R

2014-11-01

The objectives of this review are to discuss the current literature and summarise some of the promising areas with which nanotechnology may improve urological care. A Medline literature search was performed to elucidate all relevant studies of nanotechnology with specific attention to its application in urology. Urological applications of nanotechnology include its use in medical imaging, gene therapy, drug delivery, and photothermal ablation of tumours. In vitro and animal studies have shown initial encouraging results. Further study of nanotechnology for urological applications is warranted to bridge the gap between preclinical studies and translation into clinical practice, but nanomedicine has shown significant potential to improve urological patient care. © 2014 The Authors. BJU International © 2014 BJU International.

REVIEW ARTICLE: Current trends and future requirements for the mass spectrometric investigation of microbial, mammalian and plant metabolomes

NASA Astrophysics Data System (ADS)

Dunn, Warwick B.

2008-03-01

The functional levels of biological cells or organisms can be separated into the genome, transcriptome, proteome and metabolome. Of these the metabolome offers specific advantages to the investigation of the phenotype of biological systems. The investigation of the metabolome (metabolomics) has only recently appeared as a mainstream scientific discipline and is currently developing rapidly for the study of microbial, plant and mammalian metabolomes. The metabolome pipeline or workflow encompasses the processes of sample collection and preparation, collection of analytical data, raw data pre-processing, data analysis and data storage. Of these processes the collection of analytical data will be discussed in this review with specific interest shown in the application of mass spectrometry in the metabolomics pipeline. The current developments in mass spectrometry platforms (GC-MS, LC-MS, DIMS and imaging MS) and applications of specific interest will be highlighted. The current limitations of these platforms and applications will be discussed with areas requiring further development also highlighted. These include the detectable coverage of the metabolome, the identification of metabolites and the process of converting raw data to biological knowledge.

Advanced time and wavelength division multiplexing for metropolitan area optical data communication networks

NASA Astrophysics Data System (ADS)

Watford, M.; DeCusatis, C.

2005-09-01

With the advent of new regulations governing the protection and recovery of sensitive business data, including the Sarbanes-Oxley Act, there has been a renewed interest in business continuity and disaster recovery applications for metropolitan area networks. Specifically, there has been a need for more efficient bandwidth utilization and lower cost per channel to facilitate mirroring of multi-terabit data bases. These applications have further blurred the boundary between metropolitan and wide area networks, with synchronous disaster recovery applications running up to 100 km and asynchronous solutions extending to 300 km or more. In this paper, we discuss recent enhancements in the Nortel Optical Metro 5200 Dense Wavelength Division Multiplexing (DWDM) platform, including features recently qualified for data communication applications such as Metro Mirror, Global Mirror, and Geographically Distributed Parallel Sysplex (GDPS). Using a 10 Gigabit/second (Gbit/s) backbone, this solution transports significantly more Fibre Channel protocol traffic with up to five times greater hardware density in the same physical package. This is also among the first platforms to utilize forward error correction (FEC) on the aggregate signals to improve bit error rate (BER) performance beyond industry standards. When combined with encapsulation into wide area network protocols, the use of FEC can compensate for impairments in BER across a service provider infrastructure without impacting application level performance. Design and implementation of these features will be discussed, including results from experimental test beds which validate these solutions for a number of applications. Future extensions of this environment will also be considered, including ways to provide configurable bandwidth on demand, mitigate Fibre Channel buffer credit management issues, and support for other GDPS protocols.

Parallel programming of industrial applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Heroux, M; Koniges, A; Simon, H

1998-07-21

In the introductory material, we overview the typical MPP environment for real application computing and the special tools available such as parallel debuggers and performance analyzers. Next, we draw from a series of real applications codes and discuss the specific challenges and problems that are encountered in parallelizing these individual applications. The application areas drawn from include biomedical sciences, materials processing and design, plasma and fluid dynamics, and others. We show how it was possible to get a particular application to run efficiently and what steps were necessary. Finally we end with a summary of the lessons learned from thesemore » applications and predictions for the future of industrial parallel computing. This tutorial is based on material from a forthcoming book entitled: "Industrial Strength Parallel Computing" to be published by Morgan Kaufmann Publishers (ISBN l-55860-54).« less

EnviroAtlas - Synthetic N fertilizer application to agricultural lands by 12-digit HUC in the Conterminous United States, 2006

EPA Pesticide Factsheets

This EnviroAtlas dataset contains data on the mean synthetic nitrogen (N) fertilizer application to cultivated crop and hay/pasture lands per 12-digit Hydrologic Unit (HUC) in 2006. Synthetic N fertilizer inputs in 2006 were estimated using county-level estimates of farm N fertilizer inputs. We acquired county-level data describing total farm-level inputs (kg N/yr) of synthetic N fertilizer to individual counties in 2006 from the United States Geological Survey (USGS) (http://pubs.usgs.gov/sir/2012/5207/). These data were converted to per area rates (kg N/ha/yr) of synthetic N fertilizer application by dividing the total N input by the land area (ha) of combined cultivated crop and hay/pasture lands within a county as determined from county-level (http://cta.ornl.gov/transnet/Boundaries.html) summarization of the 2006 National Land Cover Database (NLCD; http://www.mrlc.gov/nlcd06_data.php). We distributed county-specific, annual per area N inputs rates (kg N/ha/yr) to cultivated crop and hay/pasture lands (30 x 30 m pixels) within the corresponding county using the raster calculator tool in ArcMap 10.0 (ESRI, Inc., Redlands, CA). Fertilizer data described here represent an average input to a typical agricultural land type within a county, i.e., they are not specific to individual crop types. This dataset was produced by the US EPA to support research and online mapping activities related to EnviroAtlas. EnviroAtlas (https://www.epa.gov/enviroatlas) allows the us

Flood Change Assessment and Attribution in Austrian alpine Basins

NASA Astrophysics Data System (ADS)

Claps, Pierluigi; Allamano, Paola; Como, Anastasia; Viglione, Alberto

2016-04-01

The present paper aims to investigate the sensitivity of flood peaks to global warming in the Austrian alpine basins. A group of 97 Austrian watersheds, with areas ranging from 14 to 6000 km2 and with average elevation ranging from 1000 to 2900 m a.s.l. have been considered. Annual maximum floods are available for the basins from 1890 to 2007 with two densities of observation. In a first period, until 1950, an average of 42 records of flood peaks are available. From 1951 to 2007 the density of observation increases to an average amount of contemporary peaks of 85. This information is very important with reference to the statistical tools used for the empirical assessment of change over time, that is linear quantile regressions. Application of this tool to the data set unveils trends in extreme events, confirmed by statistical testing, for the 0.75 and 0.95 empirical quantiles. All applications are made with specific (discharges/area) values . Similarly of what done in a previous approach, multiple quantile regressions have also been applied, confirming the presence of trends even when the possible interference of the specific discharge and morphoclimatic parameters (i.e. mean elevation and catchment area). Application of a geomorphoclimatic model by Allamano et al (2009) can allow to mimic to which extent the empirically available increase in air temperature and annual rainfall can justify the attribution of change derived by the empirical statistical tools. An comparison with data from Swiss alpine basins treated in a previous paper is finally undertaken.

Multifunctional composites for energy storage

NASA Astrophysics Data System (ADS)

Shuvo, Mohammad Arif I.; Karim, Hasanul; Rajib, Md; Delfin, Diego; Lin, Yirong

2014-03-01

Electrochemical super-capacitors have become one of the most important topics in both academia and industry as novel energy storage devices because of their high power density, long life cycles, and high charge/discharge efficiency. Recently, there has been an increasing interest in the development of multifunctional structural energy storage devices such as structural super-capacitors for applications in aerospace, automobiles and portable electronics. These multifunctional structural super-capacitors provide lighter structures combining energy storage and load bearing functionalities. Due to their superior materials properties, carbon fiber composites have been widely used in structural applications for aerospace and automotive industries. Besides, carbon fiber has good electrical conductivity which will provide lower equivalent series resistance; therefore, it can be an excellent candidate for structural energy storage applications. Hence, this paper is focused on performing a pilot study for using nanowire/carbon fiber hybrids as building materials for structural energy storage materials; aiming at enhancing the charge/discharge rate and energy density. This hybrid material combines the high specific surface area of carbon fiber and pseudo-capacitive effect of metal oxide nanowires which were grown hydrothermally in an aligned fashion on carbon fibers. The aligned nanowire array could provide a higher specific surface area that leads to high electrode-electrolyte contact area and fast ion diffusion rates. Scanning Electron Microscopy (SEM) and XRay Diffraction (XRD) measurements were used for the initial characterization of this nanowire/carbon fiber hybrid material system. Electrochemical testing has been performed using a potentio-galvanostat. The results show that gold sputtered nanowire hybrid carbon fiber provides 65.9% better performance than bare carbon fiber cloth as super-capacitor.

Development of a software safety process and a case study of its use

NASA Technical Reports Server (NTRS)

Knight, John C.

1993-01-01

The goal of this research is to continue the development of a comprehensive approach to software safety and to evaluate the approach with a case study. The case study is a major part of the project, and it involves the analysis of a specific safety-critical system from the medical equipment domain. The particular application being used was selected because of the availability of a suitable candidate system. We consider the results to be generally applicable and in no way particularly limited by the domain. The research is concentrating on issues raised by the specification and verification phases of the software lifecycle since they are central to our previously-developed rigorous definitions of software safety. The theoretical research is based on our framework of definitions for software safety. In the area of specification, the main topics being investigated are the development of techniques for building system fault trees that correctly incorporate software issues and the development of rigorous techniques for the preparation of software safety specifications. The research results are documented. Another area of theoretical investigation is the development of verification methods tailored to the characteristics of safety requirements. Verification of the correct implementation of the safety specification is central to the goal of establishing safe software. The empirical component of this research is focusing on a case study in order to provide detailed characterizations of the issues as they appear in practice, and to provide a testbed for the evaluation of various existing and new theoretical results, tools, and techniques. The Magnetic Stereotaxis System is summarized.

Fabrication of three dimensional patterns of wide dimensional range using microbes and their applications

NASA Astrophysics Data System (ADS)

Mehta, Sunita; Murugeson, Saravanan; Prakash, Balaji; Deepak

2015-10-01

Inspired by the wound healing property of certain trees, we report a novel microbes based additive process for producing three dimensional patterns, which has a potential of engineering applications in a variety of fields. Imposing a two dimensional pattern of microbes on a gel media and allowing them to grow in the third dimension is known from its use in biological studies. Instead, we have introduced an intermediate porous substrate between the gel media and the microbial growth, which enables three dimensional patterns in specific forms that can be lifted off and used in engineering applications. In order to demonstrate the applicability of this idea in a diverse set of areas, two applications are selected. In one, using this method of microbial growth, we have fabricated microlenses for enhanced light extraction in organic light emitting diodes, where densely packed microlenses of the diameters of hundreds of microns lead to luminance increase by a factor of 1.24X. In another entirely different type of application, braille text patterns are prepared on a normal office paper where the grown microbial colonies serve as braille tactile dots. Braille dot patterns thus prepared meet the standard specifications (size and spacing) for braille books.

Development and testing of a prototype tool for integrated assessment of chemical status in marine environments.

PubMed

Andersen, Jesper H; Murray, Ciarán; Larsen, Martin M; Green, Norman; Høgåsen, Tore; Dahlgren, Elin; Garnaga-Budrė, Galina; Gustavson, Kim; Haarich, Michael; Kallenbach, Emilie M F; Mannio, Jaakko; Strand, Jakob; Korpinen, Samuli

2016-02-01

We report the development and application of a prototype tool for integrated assessment of chemical status in aquatic environments based on substance- and matrix-specific environmental assessment criteria (thresholds). The Chemical Status Assessment Tool (CHASE) integrates data on hazardous substances in water, sediments and biota as well as bio-effect indicators and is based on a substance- or bio-effect-specific calculation of a 'contamination ratio' being the ratio between an observed concentration and a threshold value. Values <1.0 indicate areas potentially 'unaffected', while values >1.0 indicate areas potentially 'affected'. These ratios are combined within matrices, i.e. for water, sediment and biota and for biological effects. The overall assessment used a 'one out, all out principle' with regard to each matrix. The CHASE tool was tested in the Baltic Sea and the North Sea in 376 assessment units. In the former, the chemical status was >1.0 in practically all areas indicating that all areas assessed were potentially affected. The North Sea included areas classified as unaffected or affected. The CHASE tool can in combination with temporal trend assessments of individual substances be advantageous for use in remedial action plans and, in particular, for the science-based evaluation of the status and for determining which specific substances are responsible for a status as potentially affected.

Porous Nanocomposite Comprising Ultralong Hydroxyapatite Nanowires Decorated with Zinc-Containing Nanoparticles and Chitosan: Synthesis and Application in Bone Defect Repair.

PubMed

Sun, Tuan-Wei; Yu, Wei-Lin; Zhu, Ying-Jie; Chen, Feng; Zhang, Yong-Gang; Jiang, Ying-Ying; He, Yao-Hua

2018-06-21

Hydroxyapatite nanowires exhibit a great potential in biomedical applications owing to their high specific surface area, high flexibility, excellent mechanical properties, and similarity to mineralized collagen fibrils of natural bone. In this work, zinc-containing nanoparticle-decorated ultralong hydroxyapatite nanowires (Zn-UHANWs) with a hierarchical nanostructure have been synthesized by a one-step solvothermal method. The highly flexible Zn-UHANWs exhibit a hierarchical rough surface and enhanced specific surface area as compared with ultralong hydroxyapatite nanowires (UHANWs). To evaluate the potential application of Zn-UHANWs in bone regeneration, the biomimetic Zn-UHANWs/chitosan (CS) (Zn-UHANWs/CS) composite porous scaffold with 80 wt % Zn-UHANWs was prepared by incorporating Zn-UHANWs into the chitosan matrix by the freeze-drying process. The as-prepared Zn-UHANWs/CS composite porous scaffold exhibits enhanced mechanical properties, highly porous structure, and excellent water retention capacity. In addition, the Zn-UHANWs/CS porous scaffold has a good biodegradability with the sustainable release of Zn, Ca, and P elements in aqueous solution. More importantly, the Zn-UHANWs/CS porous scaffold can promote the osteogenic differentiation of rat bone marrow derived mesenchymal stem cells and facilitate in vivo bone regeneration as compared with the pure CS porous scaffold or UHANWs/CS porous scaffold. Thus, both the Zn-UHANWs and Zn-UHANWs/CS porous scaffold developed in this work are promising for application in bone defect repair. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Laboratory-scale study of possible use of residual sludge from glass sand beneficiation

NASA Astrophysics Data System (ADS)

Prikryl, Richard; Weishauptova, Zuzana; Zach, Jaroslav; Kozlovcev, Petr

2016-04-01

Beneficiation of quartz sand from sedimentary deposits for glass sands results in significant amounts of under-size fraction, a sludge rich in clay minerals. This sludge is considered as a waste and is returned in mined-out spaces for a simple rehabilitation, which is also the case of one of the largest glass sand production areas in the Czech Republic. The amount of produced waste sludge in the studied area (glass sand works in Provodín area, Bohemian Cretaceous Basin) is about 20 kt per year. In the recent study, we have focused on possible employment of this waste material for three applications: (1) a clay component in a raw material mixture for making of hydraulic lime, (2) a kaolinite absorbent, and (3) a geotechnical material. The sampled sludge was primarily analysed for mineralogical and chemical composition, mechanical and physical properties, the specific surface area, and parameters of pore space. X-ray analysis proved the presence of kaolinite, illite (both WCI and PCI), quartz, and accessory microcline. According to silicate analysis, the material is composed of SiO2 (80.52 wt. %), Al2O3 (11.36 wt. %), and K2O (2.14 wt. %). For its potential use as an artificial admixture for hydraulic lime production, the studied material was mixed with pure limestone in ratio of 10, 15, 20, and/or 25 wt. %. The experimental mixtures were burnt in the temperature range from 850 to 1,200°C. XRD was employed for the detection of newly formed phases showing formation of hydraulic phase such as C2S, C3A, C4AF starting from the 1050°C burning temperature. Peak burning temperature significantly influenced amount of individual phases in the burnt product. Second possible mode of use of the investigated waste material focused on its application as a sorbent. Pore space and specific surface area characteristics (SBET 7.4 sq. m/g) range this material to the group of low grade kaolinite-dominated adsorbents. Thermal treatment (burning of raw waste material at temperatures of 500°C and/or 900°C) lead to rapid deterioration of specific surface area, probably due to the structural and phase changes of dominant clay minerals. The latest considered use in the field of geotechnical applications proved possible employment of the studied material as a sealing clay for smaller dams, ponds and/or as a geotechnical barrier for waste dumps.

Detection of ground deformation in the broader area of Sharm El- Shiekh (Sinai Peninsula, Egypt) by SAR interferometry

NASA Astrophysics Data System (ADS)

Seleem, Tarek A.; Foumelis, Michael; Parcharidis, Issaak

2009-09-01

Sharm El-Shiekh area is located in the most southern part of Sinai Peninsula boarded by the Gulf of Suez to the west and by the Gulf of Aqaba to the east. The present study concerns the application of Multibaseline/Stacking Differential SAR Interferometry (DInSAR) in order to monitor ground deformation rates in the southern part of Sharm El-Shiekh area. The specific technique was applied in order to reduce the influence of atmospheric effects on ground deformation estimates. For this purpose a total number of 24 ENVISAT ASAR scenes covering the period between 2002 and 2008 were processed and analysed. Interferometric results show both patterns of uplift and downlift in the study area. Specifically an area along the coastline with a N-S direction, corresponding to the build up zone of Sharm El-Shiekh, shows average annual subsidence rates between -5 and -7 mm/yr along the line of sight (LOS). On the contrary, Sharm El Maya, an inner zone parallel to the above subsided area, shows slant range uplift of around 5 mm/yr. The obtained results of SAR inteferometry probably indicate the presence of an active fault that affects the coastal zones of Sharm El-Shiekh area.

High temperature co-axial winding transformers

NASA Technical Reports Server (NTRS)

Divan, Deepakraj M.; Novotny, Donald W.

1993-01-01

The analysis and design of co-axial winding transformers is presented. The design equations are derived and the different design approaches are discussed. One of the most important features of co-axial winding transformers is the fact that the leakage inductance is well controlled and can be made low. This is not the case in conventional winding transformers. In addition, the power density of co-axial winding transformers is higher than conventional ones. Hence, using co-axial winding transformers in a certain converter topology improves the power density of the converter. The design methodology used in meeting the proposed specifications of the co-axial winding transformer specifications are presented and discussed. The final transformer design was constructed in the lab. Co-axial winding transformers proved to be a good choice for high power density and high frequency applications. They have a more predictable performance compared with conventional transformers. In addition, the leakage inductance of the transformer can be controlled easily to suit a specific application. For space applications, one major concern is the extraction of heat from power apparatus to prevent excessive heating and hence damaging of these units. Because of the vacuum environment, the only way to extract heat is by using a cold plate. One advantage of co-axial winding transformers is that the surface area available to extract heat from is very large compared to conventional transformers. This stems from the unique structure of the co-axial transformer where the whole core surface area is exposed and can be utilized for cooling effectively. This is a crucial issue here since most of the losses are core losses.

A Large Scale Biorational Approach Using Bacillus thuringiensis israeliensis (Strain AM65-52) for Managing Aedes aegypti Populations to Prevent Dengue, Chikungunya and Zika Transmission

PubMed Central

Pruszynski, Catherine A.; Hribar, Lawrence J.; Mickle, Robert; Leal, Andrea L.

2017-01-01

Background Aedes aegypti is a container-inhabiting mosquito and a vector of dengue, chikungunya, and Zika viruses. In 2009 several cases of autochthonous dengue transmission were reported in Key West, Florida, USA prompting a comprehensive response to control A. aegypti. In Key West, larvae of this mosquito develop in containers around human habitations which can be numerous and labor intensive to find and treat. Aerial applications of larvicide covering large areas in a short time can be an efficient and economical method to control A. aegypti. Bacillus thuringiensis israelensis (Bti) is a bacterial larvicide which is highly target specific and appropriate for wide area spraying over urban areas, but to date, there are no studies that evaluate aerial spraying of Bti to control container mosquitoes like A. aegypti. Methodology This paper examines the effectiveness of aerial larvicide applications using VectoBac® WG, a commercially available Bti formulation, for A. aegypti control in an urban setting in the USA. Droplet characteristics and spray drop deposition were evaluated in Key West, Florida, USA. The mortality of A. aegypti in containers placed under canopy in an urban environment was also evaluated. Efficacy of multiple larvicide applications on adult female A. aegypti population reduction was compared between an untreated control and treatment site. Conclusions Droplet characteristics showed that small droplets can penetrate through dense canopy to reach small containers. VectoBac WG droplets reached small containers under heavy canopy in sufficient amounts to cause > 55% mortality on all application days and >90% mortality on 3 of 5 application days while controls had <5% mortality. Aerial applications of VectoBac WG caused significant decrease in adult female populations throughout the summer and during the 38th week (last application) the difference in adult female numbers between untreated and treated sites was >50%. Aerial larvicide applications using VectoBac WG can cover wide areas in a short period of time and can be effective in controlling A. aegypti and reducing A. aegypti-borne transmission in urban areas similar to Key West, Florida, USA. PMID:28199323

Telerehabilitation clinical and vocational applications for assistive technology: research, opportunities, and challenges.

PubMed

Schmeler, Mark R; Schein, Richard M; McCue, Michael; Betz, Kendra

2009-01-01

Rehabilitation service providers in rural or underserved areas are often challenged in meeting the needs of their complex patients due to limited resources in their geographical area. Recruitment and retention of the rural clinical workforce are beset by the ongoing problems associated with limited continuing education opportunities, professional isolation, and the challenges inherent in coordinating rural community healthcare. People with disabilities who live in rural communities also face challenges accessing healthcare. Traveling long distances to a specialty clinic for necessary expertise may be troublesome due to inadequate or unavailable transportation, disability specific limitations, and financial limitations. Distance and lack of access are just two threats to quality of care that now being addressed by the use of videoconferencing, information exchange, and other telecommunication technologies that facilitate telerehabilitation. This white paper illustrates and summarizes clinical and vocational applications of telerehabilitation. We provide definitions related to the fields of telemedicine, telehealth, and telerehabilitation, and consider the impetus for telerehabilitation. We review the telerehabilitation literature for assistive technology applications; pressure ulcer prevention; virtual reality applications; speech-language pathology applications; seating and wheeled mobility applications; vocational rehabilitation applications; and cost-effectiveness. We then discuss external telerehabilitation influencers, such as the positions of professional organizations. Finally, we summarize clinical and policy issues in a limited context appropriate to the scope of this paper.

An application for delivering field results to mobile devices

NASA Astrophysics Data System (ADS)

Kanta, A.; Hloupis, G.; Vallianatos, F.; Rust, D.

2009-04-01

Mobile devices (MD) such as personal digital assistants (PDAs) and Smartphones expand the ability of Internet communication between remote users. In particular these devices have the possibility to interact with data centres in order to request and receive information. For field surveys MDs used primarily for controlling instruments (in case of field measurements) or for entering data needed for later processing (e.g damage description after a natural hazard). It is not unusual in areas with high interest combined measurements took place. The results from these measurements usually stored in data servers and their publicity is driven mainly by web-based applications. Here we present a client / server application capable of displaying the results of several measurements for a specific area to a MD. More specific, we develop an application than can present to the screen of the MD the results of existing measurements according to the position of the user. The server side hosted at data centre and uses a relational data base (including the results), a SMS/MMS gateway and a receiver daemon application waiting for messages from MDs. The client side runs on MD and is a simple menu driven application which asks the user to enter the type of requested data and the geographical coordinates. In case of embedded GPS receiver, coordinates automatically derived from the receiver. Then a message is sent to server which responds with the results. In case of absence of Internet communication the application can switched to common Short/Multimedia Messaging Systems: the client request data using SMS and the server responds with MMS. We demonstrate the application using results from TEM, VES and HVSR measurements Acknowledgements Work of authors AK, GH and FV is partially supported by the EU-FP6-SSA in the frame of project "CYCLOPS: CYber-Infrastructure for CiviL protection Operative ProcedureS"

A forester's look at the application of image manipulation techniques to multitemporal Landsat data

NASA Technical Reports Server (NTRS)

Williams, D. L.; Stauffer, M. L.; Leung, K. C.

1979-01-01

Registered, multitemporal Landsat data of a study area in central Pennsylvania were analyzed to detect and assess changes in the forest canopy resulting from insect defoliation. Images taken July 19, 1976, and June 27, 1977, were chosen specifically to represent forest canopy conditions before and after defoliation, respectively. Several image manipulation and data transformation techniques, developed primarily for estimating agricultural and rangeland standing green biomass, were applied to these data. The applicability of each technique for estimating the severity of forest canopy defoliation was then evaluated. All techniques tested had highly correlated results. In all cases, heavy defoliation was discriminated from healthy forest. Areas of moderate defoliation were confused with healthy forest on northwest (NW) aspects, but were distinct from healthy forest conditions on southeast (SE)-facing slopes.

The National Research Service Award: strategies for developing a successful proposal.

PubMed

Parker, Barbara; Steeves, Richard

2005-01-01

An important experience for doctoral students is developing and submitting an application for a National Research Service Award (NRSA) from the National Institutes of Health (NIH). This article provides an overview of the process of developing and submitting an NRSA proposal from the perspective of a sponsor of successful proposals as well as a member of the Scientific Review Section. Topics included are suggestions for writing and rewriting the proposal, developing a training plan specific to the proposal, selection of sponsors consultants and references, the review process, and revising and resubmitting a proposal. Tables give examples of (a) applicants identifying strengths and areas for growth, (b) activities to address areas for growth (c), and responses to a previous review. The intended audience is beginning doctoral students and novice sponsors.

Investigations of a bearing fault detector for railroad bearings

NASA Technical Reports Server (NTRS)

Wilson, D. S.; Frarey, J. L.

1975-01-01

The laboratory tests are described which were conducted on new and damaged bearings to determine the feasibility of using high-frequency vibration as a diagnostic tool. A high-frequency band pass filter and demodulator was assembled to permit field measurements of the high-frequency vibrations. Field tests were conducted on an actual truck and on an axle assembly run in a grease test rig. These field tests were directed toward demonstration of the suitability and capabilities of the high-frequency technique for field application. Two specific areas of field application were identified as being cost effective for railroad use. One area is the examination of railroad roller bearings at a derailment site, and the second is as a wayside detector to supplement present hot box detectors for defective roller bearings.

Survey on the use of smart and adaptive engineering systems in medicine.

PubMed

Abbod, M F; Linkens, D A; Mahfouf, M; Dounias, G

2002-11-01

In this paper, the current published knowledge about smart and adaptive engineering systems in medicine is reviewed. The achievements of frontier research in this particular field within medical engineering are described. A multi-disciplinary approach to the applications of adaptive systems is observed from the literature surveyed. The three modalities of diagnosis, imaging and therapy are considered to be an appropriate classification method for the analysis of smart systems being applied to specified medical sub-disciplines. It is expected that future research in biomedicine should identify subject areas where more advanced intelligent systems could be applied than is currently evident. The literature provides evidence of hybridisation of different types of adaptive and smart systems with applications in different areas of medical specifications. Copyright 2002 Elsevier Science B.V.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kurt Derr; Milos Manic

Time and location data play a very significant role in a variety of factory automation scenarios, such as automated vehicles and robots, their navigation, tracking, and monitoring, to services of optimization and security. In addition, pervasive wireless capabilities combined with time and location information are enabling new applications in areas such as transportation systems, health care, elder care, military, emergency response, critical infrastructure, and law enforcement. A person/object in proximity to certain areas for specific durations of time may pose a risk hazard either to themselves, others, or the environment. This paper presents a novel fuzzy based spatio-temporal risk calculationmore » DSTiPE method that an object with wireless communications presents to the environment. The presented Matlab based application for fuzzy spatio-temporal risk cluster extraction is verified on a diagonal vehicle movement example.« less

Multimedia Information eXchange for I-NET, Inc. at the Kennedy Space Center: A continuing study of the application of worldwideweb technology

NASA Technical Reports Server (NTRS)

Metcalf, David

1995-01-01

Multimedia Information eXchange (MIX) is a multimedia information system that accommodates multiple data types and provides consistency across platforms. Information from all over the world can be accessed quickly and efficiently with the Internet-based system. I-NET's MIX uses the World Wide Web and Mosaic graphical user interface. Mosaic is available on all platforms used at I-NET's Kennedy Space Center (KSC) facilities. Key information system design concepts and benefits are reviewed. The MIX system also defines specific configuration and helper application parameters to ensure consistent operations across the entire organization. Guidelines and procedures for other areas of importance in information systems design are also addressed. Areas include: code of ethics, content, copyright, security, system administration, and support.

Enhancing the Exploitation of Functional Nanomaterials through Spatial Confinement: The Case of Inorganic Submicrometer Capsules.

PubMed

Vaz, Belén; Salgueiriño, Verónica; Pérez-Lorenzo, Moisés; Correa-Duarte, Miguel A

2015-08-18

Hollow inorganic nanostructures have attracted much interest in the last few years due to their many applications in different areas of science and technology. In this Feature Article, we overview part of our current work concerning the collective use of plasmonic and magnetic nanoparticles located in voided nanostructures and explore the more specific operational issues that should be taken into account in the design of inorganic nanocapsules. Along these lines, we focus our attention on the applications of silica-based submicrometer capsules aiming to stress the importance of creating nanocavities in order to further exploit the great potential of these functional nanomaterials. Additionally, we will examine some of the recent research on this topic and try to establish a perspective for future developments in this area.

Application of statistical process control and process capability analysis procedures in orbiter processing activities at the Kennedy Space Center

NASA Technical Reports Server (NTRS)

Safford, Robert R.; Jackson, Andrew E.; Swart, William W.; Barth, Timothy S.

1994-01-01

Successful ground processing at KSC requires that flight hardware and ground support equipment conform to specifications at tens of thousands of checkpoints. Knowledge of conformance is an essential requirement for launch. That knowledge of conformance at every requisite point does not, however, enable identification of past problems with equipment, or potential problem areas. This paper describes how the introduction of Statistical Process Control and Process Capability Analysis identification procedures into existing shuttle processing procedures can enable identification of potential problem areas and candidates for improvements to increase processing performance measures. Results of a case study describing application of the analysis procedures to Thermal Protection System processing are used to illustrate the benefits of the approaches described in the paper.

SIAM conference on inverse problems: Geophysical applications. Final technical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1995-12-31

This conference was the second in a series devoted to a particular area of inverse problems. The theme of this series is to discuss problems of major scientific importance in a specific area from a mathematical perspective. The theme of this symposium was geophysical applications. In putting together the program we tried to include a wide range of mathematical scientists and to interpret geophysics in as broad a sense as possible. Our speaker came from industry, government laboratories, and diverse departments in academia. We managed to attract a geographically diverse audience with participation from five continents. There were talks devotedmore » to seismology, hydrology, determination of the earth`s interior on a global scale as well as oceanographic and atmospheric inverse problems.« less

Rational application of adenosine deaminase activity in cerebrospinal fluid for the diagnosis of tuberculous meningitis.

PubMed

Parra-Ruiz, Jorge; Ramos, V; Dueñas, C; Coronado-Álvarez, N M; Cabo-Magadán, R; Portillo-Tuñón, V; Vinuesa, D; Muñoz-Medina, L; Hernández-Quero, J

2015-10-01

Tuberculous meningitis (TBM) is one of the most serious and difficult to diagnose manifestations of TB. An ADA value >9.5 IU/L has great sensitivity and specificity. However, all available studies have been conducted in areas of high endemicity, so we sought to determine the accuracy of ADA in a low endemicity area. This retrospective study included 190 patients (105 men) who had ADA tested in CSF for some reason. Patients were classified as probable/certain TBM or non-TBM based on clinical and Thwaite's criteria. Optimal ADA cutoff was established by ROC curves and a predictive algorithm based on ADA and other CSF biochemical parameters was generated. Eleven patients were classified as probable/certain TBM. In a low endemicity area, the best ADA cutoff was 11.5 IU/L with 91 % sensitivity and 77.7 % specificity. We also developed a predictive algorithm based on the combination of ADA (>11.5 IU/L), glucose (<65 mg/dL) and leukocytes (≥13.5 cell/mm(3)) with increased accuracy (Se: 91 % Sp: 88 %). Optimal ADA cutoff value in areas of low TB endemicity is higher than previously reported. Our algorithm is more accurate than ADA activity alone with better sensitivity and specificity than previously reported algorithms.

A PRELIMINARY assessment of BCG vacination in India.

PubMed

1955-01-01

A NEW ASSESSMENT ACTIVITY IN RELATION TO THE WHO/UNICEF BCG VACCINATION PROGRAMME IS DESCRIBED IN THIS REPORT: according to a detailed plan special field teams collect data on tuberculin sensitivity to determine how efficiently children are being selected for vaccination and to appraise the allergy produced by the mass vaccinations. Results of nine months' work in India have important implications for the practical BCG work.Testing of unvaccinated groups of schoolchildren shows that the pattern of tuberculin sensitivity differs in different parts of India. Specific tuberculin sensitivity is found in all areas, as evidenced by strong reactions to the 5 TU test. Many children had a low-grade non-specific sensitivity, evidenced by small reactions to 5 TU and large reactions to 100 TU. This non-specific tuberculin sensitivity was less frequent at high altitudes, and most common in low-lying humid areas: in all areas it was more prevalent than specific sensitivity.In some areas non-specific tuberculin sensitivity is so strong that it cannot be effectively distinguished from specific sensitivity: consequently, many children not infected with tuberculosis are undoubtedly being excluded from vaccination.Sample retesting of children vaccinated in the mass campaign revealed variable levels of allergy, in many instances much lower than had been expected. These results cannot be explained by a native incapacity of the Indian children to develop strong allergy-nor presumably by the vaccine used. Impairment of the vaccine by exposure to light could be no more than a contributory factor. The marked variability of the campaign results suggests that some factor connected with the handling or application of the vaccine (or possibly of the tuberculin) is involved.

Composite material application for liquid rocket engines

NASA Technical Reports Server (NTRS)

Heubner, S. W.

1982-01-01

With increasing emphasis on improving engine thrust-to-weight ratios to provide improved payload capabilities, weight reductions achievable by the use of composites have become attractive. Of primary significance is the weight reduction offered by composites, although high temperature properties and cost reduction were also considered. The potential for application of composites to components of Earth-to-orbit hydrocarbon engines and orbit-to-orbit LOX/H2 engines was assessed. The components most likely to benefit from the application of composites were identified, as were the critical technology areas where developed would be required. Recommendations were made and a program outlined for the design, fabrication, and demonstration of specific engine components.

Establishment of first engineering specifications for environmental modification to eliminate schistosomiasis epidemic foci in urban areas.

PubMed

Kong, Shibo; Tan, Xiaodong; Deng, Zhiqing; Xie, Yaofei; Yang, Fen; Zheng, Zengwang

2017-08-01

Snail control is a key link in schistosomiasis control, but no unified methods for eliminating snails have been produced to date. This study was conducted to explore an engineering method for eliminating Oncomelania hupensis applicable to urban areas. The engineering specifications were established using the Delphi method. An engineering project based on these specifications was conducted in Hankou marshland to eliminate snails, including the transformation of the beach surface and ditches. Molluscicide was used as a supplement. The snail control effect was evaluated by field investigation. The engineering results fulfilled the requirements of the design. The snail density decreased to 0/0.11m 2 , and the snail area dropped to 0m 2 after the project. There was a statistically significant difference in the number of frames with snails before and after the project (P<0.05). Snails were completely eliminated through one year of continuous monitoring, and no new snails were found after a flood disaster. This study demonstrates that engineering specifications for environmental modification were successfully established. Environmental modification, mainly through beach and ditch remediation, can completely change the environment of Oncomelania breeding. This method of environmental modification combined with mollusciciding was highly effective at eliminating snails. Copyright © 2017 Elsevier B.V. All rights reserved.

Popcorn-Derived Porous Carbon Flakes with an Ultrahigh Specific Surface Area for Superior Performance Supercapacitors.

PubMed

Hou, Jianhua; Jiang, Kun; Wei, Rui; Tahir, Muhammad; Wu, Xiaoge; Shen, Ming; Wang, Xiaozhi; Cao, Chuanbao

2017-09-13

Popcorn-derived porous carbon flakes have been successfully fabricated from the biomass of maize. Utilizing the "puffing effect", the nubby maize grain turned into materials with an interconnected honeycomb-like porous structure composed of carbon flakes. The following chemical activation method enabled the as-prepared products to possess optimized porous structures for electrochemical energy-storage devices, such as multilayer flake-like structures, ultrahigh specific surface area (S BET : 3301 m 2 g -1 ), and a high content of micropores (microporous surface area of 95%, especially the optimized sub-nanopores with the size of 0.69 nm) that can increase the specific capacitance. The as-obtained sample displayed excellent specific capacitance of 286 F g -1 at 90 A g -1 for supercapacitors. Moreover, the unique porous structure demonstrated an ideal way to improve the volumetric energy density performance. A high energy density of 103 Wh kg -1 or 53 Wh L -1 has been obtained in the case of ionic liquid electrolyte, which is the highest among reported biomass-derived carbon materials and will satisfy the urgent requirements of a primary power source for electric vehicles. This work may prove to be a fast, green, and large-scale synthesis route by using the large nubby granular materials to synthesize applicable porous carbons in energy-storage devices.

A cone-shaped 3D carbon nanotube probe for neural recording.

PubMed

Su, Huan-Chieh; Lin, Chia-Min; Yen, Shiang-Jie; Chen, Yung-Chan; Chen, Chang-Hsiao; Yeh, Shih-Rung; Fang, Weileun; Chen, Hsin; Yao, Da-Jeng; Chang, Yen-Chung; Yew, Tri-Rung

2010-09-15

A novel cone-shaped 3D carbon nanotube (CNT) probe is proposed as an electrode for applications in neural recording. The electrode consists of CNTs synthesized on the cone-shaped Si (cs-Si) tip by catalytic thermal chemical vapor deposition (CVD). This probe exhibits a larger CNT surface area with the same footprint area and higher spatial resolution of neural recording compared to planar-type CNT electrodes. An approach to improve CNT characteristics by O(2) plasma treatment to modify the CNT surface will be also presented. Electrochemical characterization of O(2) plasma-treated 3D CNT (OT-CNT) probes revealed low impedance per unit area (∼64.5 Ω mm(-2)) at 1 kHz and high specific capacitance per unit area (∼2.5 mF cm(-2)). Furthermore, the OT-CNT probes were employed to record the neural signals of a crayfish nerve cord. Our findings suggest that OT-CNT probes have potential advantages as high spatial resolution and superb electrochemical properties which are suitable for neural recording applications. Copyright 2010 Elsevier B.V. All rights reserved.

NASA/Drexel program. [research effort in large-scale technical programs management for application to urban problems

NASA Technical Reports Server (NTRS)

1973-01-01

The results are reported of the NASA/Drexel research effort which was conducted in two separate phases. The initial phase stressed exploration of the problem from the point of view of three primary research areas and the building of a multidisciplinary team. The final phase consisted of a clinical demonstration program in which the research associates consulted with the County Executive of New Castle County, Delaware, to aid in solving actual problems confronting the County Government. The three primary research areas of the initial phase are identified as technology, management science, and behavioral science. Five specific projects which made up the research effort are treated separately. A final section contains the conclusions drawn from total research effort as well as from the specific projects.

Thin-film rechargeable lithium batteries

NASA Astrophysics Data System (ADS)

Dudney, N. J.; Bates, J. B.; Lubben, D.

1994-11-01

Small thin-film rechargeable cells have been fabricated with a lithium phosphorus oxynitride electrolyte, Li metal anode, and Li(1-x)Mn2O4 as the cathode film. The cathode films were fabricated by several different techniques resulting in both crystalline and amorphous films. These were compared by observing the cell discharge behavior. Estimates have been made for the scale-up of such a thin-film battery to meet the specifications for the electric vehicle application. The specific energy, energy density, and cycle life are expected to meet the USABC mid-term criteria. However, the areas of the thin-films needed to fabricate such a cell are very large. The required areas could be greatly reduced by operating the battery at temperatures near 100 C or by enhancing the lithium ion transport rate in the cathode material.

Direct Application of the INNO-LiPA Rif.TB Line-Probe Assay for Rapid Identification of Mycobacterium tuberculosis Complex Strains and Detection of Rifampin Resistance in 360 Smear-Positive Respiratory Specimens from an Area of High Incidence of Multidrug-Resistant Tuberculosis

PubMed Central

Viveiros, Miguel; Leandro, Clara; Rodrigues, Liliana; Almeida, Josefina; Bettencourt, Rosário; Couto, Isabel; Carrilho, Lurdes; Diogo, José; Fonseca, Ana; Lito, Luís; Lopes, João; Pacheco, Teresa; Pessanha, Mariana; Quirim, Judite; Sancho, Luísa; Salfinger, Max; Amaral, Leonard

2005-01-01

The INNO-LiPA Rif.TB assay for the identification of Mycobacterium tuberculosis complex strains and the detection of rifampin (RIF) resistance has been evaluated with 360 smear-positive respiratory specimens from an area of high incidence of multidrug-resistant tuberculosis (MDR-TB). The sensitivity when compared to conventional identification/culture methods was 82.2%, and the specificity was 66.7%; the sensitivity and specificity were 100.0% and 96.9%, respectively, for the detection of RIF resistance. This assay has the potential to provide rapid information that is essential for the effective management of MDR-TB. PMID:16145166

Utilization of SRS pond ash in controlled low strength material. Technical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Langton, C.A.; Rajendran, N.

1995-12-01

Design mixes for Controlled Low Strength Material (CLSM) were developed which incorporate pond ashes (fly ashes) from the A-Area Ash Pile, the old F-Area Ash Basin and the D-Area Ash Basin. CLSM is a pumpable, flowable, excavatable backfill used in a variety of construction applications at SRS. Results indicate that CLSM which meets all of the SRS design specifications for backfill, can be made with the A-, D-, and F-Area pond ashes. Formulations for the design mixes are provided in this report. Use of the pond ashes may result in a cost savings for CLSM used at SRS and willmore » utilize a by-product waste material, thereby decreasing the amount of material requiring disposal.« less

Science for Deaf Children. The Lexington School for the Deaf Education Series, Book V.

ERIC Educational Resources Information Center

Leitman, Allan

Intended for use by teachers and schools for the deaf, the booklet presents activities and units which may be used in planning and developing a science curriculum. A workshop classroom is described. Attention is given to teaching methods specifically applicable to the deaf. Suggested subject areas, materials, or activities for preschool programs…

Antenna Technologies for NASA Applications

NASA Technical Reports Server (NTRS)

Miranda, Felix

2007-01-01

This presentation addresses the efforts being performed at GRC to develop antenna technology in support of NASA s Exploration Vision. In particular, the presentation discusses the communications architecture asset-specific data services, as well as wide area coverage, high gain, low mass deployable antennas. Phased array antennas as well as electrically small, lightweight, low power, multifunctional antennas will be also discussed.

Antenna Technologies for NASA Applications

NASA Technical Reports Server (NTRS)

Miranda, Felix A.

2006-01-01

This presentation addresses the efforts being performed at GRC to develop antenna technology in support of NASA s Exploration Vision. In particular, the presentation discusses the communications architecture asset-specific data services, as well as wide area coverage, high gain, low mass deployable antennas. Phased array antennas as well as electrically small, lightweight, low power, multifunctional antennas will be also discussed.

Summary (Songbird ecology in southwestern ponderosa pine forests: A literature review)

Treesearch

William M. Block; Deborah M. Finch; Joseph L. Ganey; William H. Moir

1997-01-01

Most ornithological studies in Southwestern ponderosa pine forests have yielded results that are applicable only to the specific location and particular conditions of the study areas (for example, Green 1979 and Hurlbert 1984). In addition, varying interpretation of similar study results by investigators has limited our ability to extend or synthesize research results...

Aerodynamic Performance and Particle Image Velocimetery of Piezo Actuated Biomimetic Manduca Sexta Engineered Wings Towards the Design and Application of a Flapping Wing Flight Vehicle

DTIC Science & Technology

2013-12-01

95 3.3. Displacement sensor ... Bio vs. engineered wing modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 3.1. High speed camera specifications...expanding and evolving mission areas, especially in the arena of bio -inspired Flap- ping Wing Micro Air Vehicles (FWMAV). This chapter will introduce the

NASA Glenn Research Center Electrochemistry Branch Battery and Fuel Cell Development Overview

NASA Technical Reports Server (NTRS)

Manzo, Michelle A.

2011-01-01

This presentation covers an overview of NASA Glenn s history and heritage in the development of electrochemical systems for aerospace applications. Current developments related to batteries and fuel cells are addressed. Specific areas of focus are Li-ion batteries and Polymer Electrolyte Membrane Fuel cells systems and their development for future Exploration missions.

78 FR 48087 - Approval and Promulgation of Air Quality Implementation Plans; Ohio; Redesignation of the Canton...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-07

... specific examples to illustrate your concerns, and suggest alternatives. 7. Explain your views as clearly... 172(c)(9) contingency measures is not applicable for purposes of redesignation. Id. Section 172(c)(3... area demonstrates maintenance of the NAAQS without part D NSR. A detailed rationale for this view is...

Spinoff, 1987

NASA Technical Reports Server (NTRS)

Haggerty, James J.

1987-01-01

Various current or forthcoming NASA projects and experiments with potential for technology spinoff are described. NASA technological advances with existing commercial applications are outlined in the following areas: transportation; consumer; home; and recreation; medicine; resources management; energy; public safety; and manufacturing technology and industrial productivity. Specific systems, devices, and equipment are described. A concluding essay describes the NASA technology utilization/transfer effort.

Forging; Heat Treating and Testing; Technically Oriented Industrial Materials and Process 1: 5898.05.

ERIC Educational Resources Information Center

Dade County Public Schools, Miami, FL.

The course provides students with advanced and exploratory experience in the area of plastic deformation of metals and in the changing of the physical characteristics of metals by the controlled application and timed removal of heat. Course content includes goals, specific objectives, safety in forge work, forging tools and equipment, industrial…

Beyond Cognitive Increase: Investigating the Influence of Computer Programming on Perception and Application of Mathematical Skills

ERIC Educational Resources Information Center

Rich, Peter J.; Bly, Neil; Leatham, Keith R.

2014-01-01

This study aimed to provide first-hand accounts of the perceived long-term effects of learning computer programming on a learner's approach to mathematics. These phenomenological accounts, garnered from individual interviews of seven different programmers, illustrate four specific areas of interest: (1) programming provides context for many…

Development and application of a spatial IBM to forecast greater prairie-chicken population responses to land use in the Flint Hills region of Kansas

EPA Science Inventory

Greater prairie-chicken (Tympanachus cupido) populations have been on the decline for decades. Recent efforts to reverse this trend are focusing on two specific disturbance regimes, cattle grazing and field burning, both prevalent in the Flint Hill region of Kansas -- an area of...

Standalone Mobile Application for Shipping Services Based on Geographic Information System and A-Star Algorithm

NASA Astrophysics Data System (ADS)

Gunawan, D.; Marzuki, I.; Candra, A.

2018-03-01

Geographic Information Systems (GIS) plays an essential role in shipping service related application. By utilizing GIS, the courier can find the route to deliver goods for its customer. This research proposes a standalone mobile application to provide the shortest route to the destinations by utilizing geographic information systems with A-Star algorithm. This application is intended to be used although the area has no Internet network available. The developed application can handle several drop off points then calculates the shortest route that passes through all the drop off points. According to the conducted testing, the number of drop off points that can be calculated is influenced by the specification of the smartphone. More destinations require more smartphone resources and time to process.

Development and application of unified algorithms for problems in computational science

NASA Technical Reports Server (NTRS)

Shankar, Vijaya; Chakravarthy, Sukumar

1987-01-01

A framework is presented for developing computationally unified numerical algorithms for solving nonlinear equations that arise in modeling various problems in mathematical physics. The concept of computational unification is an attempt to encompass efficient solution procedures for computing various nonlinear phenomena that may occur in a given problem. For example, in Computational Fluid Dynamics (CFD), a unified algorithm will be one that allows for solutions to subsonic (elliptic), transonic (mixed elliptic-hyperbolic), and supersonic (hyperbolic) flows for both steady and unsteady problems. The objectives are: development of superior unified algorithms emphasizing accuracy and efficiency aspects; development of codes based on selected algorithms leading to validation; application of mature codes to realistic problems; and extension/application of CFD-based algorithms to problems in other areas of mathematical physics. The ultimate objective is to achieve integration of multidisciplinary technologies to enhance synergism in the design process through computational simulation. Specific unified algorithms for a hierarchy of gas dynamics equations and their applications to two other areas: electromagnetic scattering, and laser-materials interaction accounting for melting.

Bacteriophage recombination systems and biotechnical applications.

PubMed

Nafissi, Nafiseh; Slavcev, Roderick

2014-04-01

Bacteriophage recombination systems have been widely used in biotechnology for modifying prokaryotic species, for creating transgenic animals and plants, and more recently, for human cell gene manipulation. In contrast to homologous recombination, which benefits from the endogenous recombination machinery of the cell, site-specific recombination requires an exogenous source of recombinase in mammalian cells. The mechanism of bacteriophage evolution and their coexistence with bacterial cells has become a point of interest ever since bacterial viruses' life cycles were first explored. Phage recombinases have already been exploited as valuable genetic tools and new phage enzymes, and their potential application to genetic engineering and genome manipulation, vectorology, and generation of new transgene delivery vectors, and cell therapy are attractive areas of research that continue to be investigated. The significance and role of phage recombination systems in biotechnology is reviewed in this paper, with specific focus on homologous and site-specific recombination conferred by the coli phages, λ, and N15, the integrase from the Streptomyces phage, ΦC31, the recombination system of phage P1, and the recently characterized recombination functions of Yersinia phage, PY54. Key steps of the molecular mechanisms involving phage recombination functions and their application to molecular engineering, our novel exploitations of the PY54-derived recombination system, and its application to the development of new DNA vectors are discussed.

Site-Specific Infrared Probes of Proteins

PubMed Central

Ma, Jianqiang; Pazos, Ileana M.; Zhang, Wenkai; Culik, Robert M.; Gai, Feng

2015-01-01

Infrared spectroscopy has played an instrumental role in studying a wide variety of biological questions. However, in many cases it is impossible or difficult to rely on the intrinsic vibrational modes of biological molecules of interest, such as proteins, to reveal structural and/or environmental information in a site-specific manner. To overcome this limitation, many recent efforts have been dedicated to the development and application of various extrinsic vibrational probes that can be incorporated into biological molecules and used to site-specifically interrogate their structural and/or environmental properties. In this Review, we highlight some recent advancements of this rapidly growing research area. PMID:25580624

Construction of high-energy-density supercapacitors from pine-cone-derived high-surface-area carbons.

PubMed

Karthikeyan, Kaliyappan; Amaresh, Samuthirapandiyan; Lee, Sol Nip; Sun, Xueliang; Aravindan, Vanchiappan; Lee, Young-Gi; Lee, Yun Sung

2014-05-01

Very high surface area activated carbons (AC) are synthesized from pine cone petals by a chemical activation process and subsequently evaluated as an electrode material for supercapacitor applications in a nonaqueous medium. The maximum specific surface area of ∼3950 m(2)  g(-1) is noted for the material treated with a 1:5 ratio of KOH to pine cone petals (PCC5), which is much higher than that reported for carbonaceous materials derived from various other biomass precursors. A symmetric supercapacitor is fabricated with PCC5 electrodes, and the results showed enhanced supercapacitive behavior with the highest energy density of ∼61 Wh kg(-1). Furthermore, outstanding cycling ability is evidenced for such a configuration, and ∼90 % of the initial specific capacitance after 20,000 cycles under harsh conditions was observed. This result revealed that the pine-cone-derived high-surface-area AC can be used effectively as a promising electrode material to construct high-energy-density supercapacitors. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Few layered vanadyl phosphate nano sheets-MWCNT hybrid as an electrode material for supercapacitor application

NASA Astrophysics Data System (ADS)

Dutta, Shibsankar; De, Sukanta

2016-05-01

It have been already seen that 2-dimensional nano materials are the suitable choice for the supercapacitor application due to their large specific surface area, electrochemical active sites, micromechanical flexibility, expedite ion migration channel properties. Free standing hybrid films of functionalized MWCNT (- COOH group) and α-Vanadyl phosphates (VOPO42H2O) are prepared by vacuum filtering. The surface morphology and microstructure of the samples are studied by transmission electron microscope, field emission scanning electron microscope, XRD, Electrochemical properties of hybrid films have been investigated systematically in 1M Na2SO4 aqueous electrolyte. The hybrid material exhibits a high specific capacitance 236 F/g with high energy density of 65.6 Wh/Kg and a power density of 1476 W/Kg.

Progress in the development of paper-based diagnostics for low-resource point-of-care settings

PubMed Central

Byrnes, Samantha; Thiessen, Gregory; Fu, Elain

2014-01-01

This Review focuses on recent work in the field of paper microfluidics that specifically addresses the goal of translating the multistep processes that are characteristic of gold-standard laboratory tests to low-resource point-of-care settings. A major challenge is to implement multistep processes with the robust fluid control required to achieve the necessary sensitivity and specificity of a given application in a user-friendly package that minimizes equipment. We review key work in the areas of fluidic controls for automation in paper-based devices, readout methods that minimize dedicated equipment, and power and heating methods that are compatible with low-resource point-of-care settings. We also highlight a focused set of recent applications and discuss future challenges. PMID:24256361

Control of microbial contamination.

NASA Technical Reports Server (NTRS)

Mcdade, J. J.

1971-01-01

Two specific applications are discussed of microbial contamination control in planetary quarantine. Under the first concept, using the clean room to control environmental microorganisms, the objective is to reduce the microbial species and keep the numbers of microorganisms within an enclosure at a low level. The clean room concept is aimed at obtaining a product that has a controlled and reduced level of microbial contamination. Under the second concept, using the microbiological barrier to control microbial contamination of a specific product, the barrier techniques are designed to prevent the entry of any microorganisms into a sterile work area. Thus the assembly of space flight hardware within the confines of a microbiological barrier is aimed at obtaining a sterile product. In theory and practice, both approaches are shown to be applicable to the planetary quarantine program.

Structural materials issues for the next generation fission reactors

NASA Astrophysics Data System (ADS)

Chant, I.; Murty, K. L.

2010-09-01

Generation-IV reactor design concepts envisioned thus far cater to a common goal of providing safer, longer lasting, proliferation-resistant, and economically viable nuclear power plants. The foremost consideration in the successful development and deployment of Gen-W reactor systems is the performance and reliability issues involving structural materials for both in-core and out-of-core applications. The structural materials need to endure much higher temperatures, higher neutron doses, and extremely corrosive environments, which are beyond the experience of the current nuclear power plants. Materials under active consideration for use in different reactor components include various ferritic/martensitic steels, austenitic stainless steels, nickel-base superalloys, ceramics, composites, etc. This article addresses the material requirements for these advanced fission reactor types, specifically addressing structural materials issues depending on the specific application areas.

A mobile phone application for the collection of opinion data for forest planning purposes.

PubMed

Kangas, Annika; Rasinmäki, Jussi; Eyvindson, Kyle; Chambers, Philip

2015-04-01

The last 30 years has seen an increase in environmental, socio-economic, and recreational objectives being considered throughout the forest planning process. In the Finnish context these are considered mainly at the regional level potentially missing out on more local issues and problems. Such local information would be most efficiently collected with a participatory GIS approach. A mobile participatory GIS application called Tienoo was developed as a tool for collecting location-specific opinions of recreational and aesthetical characteristics of forests and forest management. The application also contains information the user can access regarding the practical details of the area, for instance about the recreational infrastructure. The application was tested in Ruunaa National Hiking Area, North Karelia, Eastern Finland. Through this application it is possible to continuously collect geolocated preference information. As a result, the collected opinions have details which can be located in both time and space. This allows for the possibility to monitor the changes in opinions when the stands are treated, and it also allows for easily analyzing the effect of time of year on the opinions. It is also possible to analyze the effect of the spatial location and the forest characteristics on the opinions using GIS analysis.

Nanoscience and nanotechnologies in food industries: opportunities and research trends

NASA Astrophysics Data System (ADS)

Ranjan, Shivendu; Dasgupta, Nandita; Chakraborty, Arkadyuti Roy; Melvin Samuel, S.; Ramalingam, Chidambaram; Shanker, Rishi; Kumar, Ashutosh

2014-06-01

Nanomaterials have gained importance in various fields of science, technology, medicine, colloid technologies, diagnostics, drug delivery, personal care applications and others due to their small size and unique physico-chemical characteristic. Apart from above mentioned area, it is also extensively being used in food sector specifically in preservation and packaging. The future applications in food can also be extended to improve the shelf life, food quality, safety, fortification and biosensors for contaminated or spoiled food or food packaging. Different types and shapes of nanomaterials are being employed depending upon the need and nature of the food. Characterisation of these nanomaterials is essential to understand the interaction with the food matrix and also with biological compartment. This review is focused on application of nanotechnology in food industries. It also gives insight on commercial products in market with usage of nanomaterials, current research and future aspects in these areas. Currently, they are being incorporated into commercial products at a faster rate than the development of knowledge and regulations to mitigate potential health and environmental impacts associated with their manufacturing, application and disposal. As nanomaterials are finding new application every day, care should be taken about their potential toxic effects.

Novel aptamer-linked nanoconjugate approach for detection of waterborne bacterial pathogens: an update

NASA Astrophysics Data System (ADS)

Singh, Gulshan; Manohar, Murli; Adegoke, Anthony Ayodeji; Stenström, Thor Axel; Shanker, Rishi

2017-01-01

The lack of microbiologically safe water in underdeveloped nations is the prime cause of infectious disease outbreaks. The need for the specific identification and detection of microorganisms encourages the development of advanced, rapid, sensitive and highly specific methods for the monitoring of pathogens and management of potential risk to human health. The rapid molecular assays based on detection of specific molecular signatures offer advantages over conventional methods in terms of specificity and sensitivity but require complex instrumentation and skilled personnel. Nanotechnology is an emerging area and provides a robust approach for the identification of pathogenic microorganism utilizing the peculiar properties of nanomaterials, i.e. small size (1-100 nm) and large surface area. This emerging technology promises to fulfill the urgent need of a novel strategy to enhance the bacterial identification and quantitation in the environment. In this context, the peculiar properties of gold nanoparticles, their plasmonic shifts, and changes in magnetic properties have been utilized for the simple and cost-effective detection of bacterial nucleic acids, antigens and toxins with quite improved sensitivity. One of the promising leads to develop an advance detection method might be the coupling of nucleic acid aptamers (capable of interacting specifically with bacteria, protozoa, and viruses) with nanomaterials. Such aptamer-nano conjugate can be used for the specific recognition of infectious agents in different environmental matrices. This review summarizes the application of nanotechnology in the area of pathogen detection and discusses the prospects of coupling nucleic acid aptamers with nanoparticles for the specific detection of targeted pathogens.

LANDSAT digital data processing: A near real-time application. [Gulf of Mexico

NASA Technical Reports Server (NTRS)

Barker, J. L.; Bohn, C.; Stuart, L.; Hill, J.

1975-01-01

An application of rapid generation of classed digital images from LANDSAT-1 was demonstrated and its feasibility evaluated by NASA in conjunction with the Environmental Protection Agency (EPA), Texas A and M University (TAMU), and the Cousteau Society. The primary purpose was to show that satellite data could be processed and transmitted to the Calypso, which was used as a research vessel, in time for use in directing it to specific locations of possible plankton upwellings, sediment, or other anomalies in the coastal water areas along the Gulf of Mexico.

Digital Beamforming Interferometry

NASA Technical Reports Server (NTRS)

Rincon, Rafael F. (Inventor)

2016-01-01

Airborne or spaceborne Syntheic Aperture Radar (SAR) can be used in a variety of ways, and is often used to generate two dimensional images of a surface. SAR involves the use of radio waves to determine presence, properties, and features of extended areas. Specifically, radio waves are 10 transmitted in the presence of a ground surface. A portion of the radio wave's energy is reflected back to the radar system, which allows the radar system to detect and image the surface. Such radar systems may be used in science applications, military contexts, and other commercial applications.

Nonparametric bootstrap analysis with applications to demographic effects in demand functions.

PubMed

Gozalo, P L

1997-12-01

"A new bootstrap proposal, labeled smooth conditional moment (SCM) bootstrap, is introduced for independent but not necessarily identically distributed data, where the classical bootstrap procedure fails.... A good example of the benefits of using nonparametric and bootstrap methods is the area of empirical demand analysis. In particular, we will be concerned with their application to the study of two important topics: what are the most relevant effects of household demographic variables on demand behavior, and to what extent present parametric specifications capture these effects." excerpt

Johnson Space Center: Workmanship Training

NASA Technical Reports Server (NTRS)

Patterson, Ashley; Sikes, Larry; Corbin, Cheryl; Rucka, Becky

2015-01-01

Special processes require special skills, knowledge and experienced application. For over 15 years, the NASA Johnson Space Center's Receiving, Inspection and Test Facility (RITF) has provided Agency-wide NASA Workmanship Standards compliance training, issuing more than 500 to 800 training completion certificates annually. It is critical that technicians and inspectors are trained and that they maintain their proficiency to implement the applicable standards and specifications. Training services include "hands-on" training to engineers, technicians, and inspectors in the areas of electrostatic discharge (ESD), soldering, surface mount technology (SMT), crimping, conformal coating, and fiber-optic terminations.

Workmanship Training Industry

NASA Technical Reports Server (NTRS)

Patterson, Ashley; Sikes, Larry; Corbin, Cheryl; Rucka, Rebecca

2015-01-01

Special processes require special skills, knowledge and experienced application. For over 15 years, the NASA Johnson Space Center's Receiving, Inspection and Test Facility (RITF) has provided Workmanship Standards compliance training, issuing more than 500 to 800 training completion certificates annually. It is critical that technicians and inspectors are trained and that they maintain their proficiency to implement the applicable standards and specifications. Training services include 'hands-on' training to engineers, technicians, and inspectors in the areas of electrostatic discharge (ESD), soldering, fiber optics, lithium battery handling, torque and wire safety, and wire wrapping.

Regulatory and scientific issues regarding use of foreign data in support of new drug applications in the United States: an FDA perspective.

PubMed

Khin, N A; Yang, P; Hung, H M J; Maung-U, K; Chen, Y-F; Meeker-O'Connell, A; Okwesili, P; Yasuda, S U; Ball, L K; Huang, S-M; O'Neill, R T; Temple, R

2013-08-01

Globalization of clinical research has led to an increase in clinical trials conducted outside of the United States that are submitted to the US Food and Drug Administration (FDA) in new drug applications. This article discusses the FDA's experience with these submissions in specific therapeutic areas, including the extent of this practice, differences between the effectiveness and safety outcomes of studies conducted inside and outside the United States, and the FDA's approach to acceptance of these trials.

The extent of the uptake of plasmid into the skin determines the immune responses induced by a DNA vaccine applied topically onto the skin

PubMed Central

Yu, Zhen; Chung, Woon-Gye; Sloat, Brian R.; Löhr, Christiane V.; Weiss, Richard; Rodriguez, B. Leticia; Li, Xinran; Cui, Zhengrong

2011-01-01

Objectives Non-invasive immunization by applying plasmid DNA topically onto the skin is an attractive immunization approach. However, the immune responses induced are generally weak. Previously, we showed that the antibody responses induced by topical DNA vaccine were significantly enhanced when hair follicles in the application area were induced into anagen (growth) stage by hair plucking. In the present study, we further investigated the mechanism of immune enhancement. Methods Three different methods, hair plucking or treatment with retinoic acid (RA) or O- tetradecanoylphorbol-13-acetate (TPA), were used to induce hair follicles into anagen stage before mice were dosed with a β-galactosidase-encoding plasmid, and the specific antibody responses induced were evaluated. Key findings The hair plucking method was more effective at enhancing the resultant antibody responses. Treatment with RA or TPA caused more damages to the skin and induced more severe local inflammations than hair plucking. However, hair plucking was most effective at enhancing the uptake or retention of the DNA in the application area. Conclusions The uptake of plasmid DNA in the application area correlated with the antibody responses induced by a topically applied DNA. PMID:21235583

Equivalent damage: A critical assessment

NASA Technical Reports Server (NTRS)

Laflen, J. R.; Cook, T. S.

1982-01-01

Concepts in equivalent damage were evaluated to determine their applicability to the life prediction of hot path components of aircraft gas turbine engines. Equivalent damage was defined as being those effects which influence the crack initiation life-time beyond the damage that is measured in uniaxial, fully-reversed sinusoidal and isothermal experiments at low homologous temperatures. Three areas of equivalent damage were examined: mean stress, cumulative damage, and multiaxiality. For each area, a literature survey was conducted to aid in selecting the most appropriate theories. Where possible, data correlations were also used in the evaluation process. A set of criteria was developed for ranking the theories in each equivalent damage regime. These criteria considered aspects of engine utilization as well as the theoretical basis and correlative ability of each theory. In addition, consideration was given to the complex nature of the loading cycle at fatigue critical locations of hot path components; this loading includes non-proportional multiaxial stressing, combined temperature and strain fluctuations, and general creep-fatigue interactions. Through applications of selected equivalent damage theories to some suitable data sets it was found that there is insufficient data to allow specific recommendations of preferred theories for general applications. A series of experiments and areas of further investigations were identified.

Photovoltaic tests and applications project

NASA Technical Reports Server (NTRS)

1978-01-01

The activities and accomplishments of the Photovoltaic Tests and Applications Project during the period April 1976 through June 1977 are summarized. Results of efforts to identify potential near-term photovoltaic applications and users are discussed, including the outcome of an extensive survey of Federal government agencies. The status of application experiments is presented. Various general engineering efforts are reported, including the design and construction of a photovoltaic Systems Test Facility. Efforts to develop a high efficiency 10 kVA self-commutated inverter and controller specifically designed for photovoltaic systems are also discussed. The results of a wide variety of activities in the area of photovoltaic measurements and standards are related. Documents generated by the Project during the reporting period are listed in an Appendix.

Electroplating targets for production of unique PET radionuclides

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bui, V.; Sheh, Y.; Finn, R.

1994-12-31

The past decade has witnessed the applications of Positron Emission Tomography (PET) evolving from a purely research endeavour to a procedure which has specific clinical applications in the areas of cardiology, neurology and oncology. The growth of PET has been facilitated by developments in medical instrumentation and radiopharmaceutical chemistry efforts. Included in this latter effort has been the low energy accelerator production and processing of unique PET radionuclides appropriate for the radiolabeling of biomolecules i.e. monoclonal antibodies and pepetides. The development and application of electroplated targets of antimony and copper for the production of iodine-124 and gallium-66 respectively, utilizing themore » Memorial Sloan-Kettering Cancer Center cyclotron are examples of target design and development applicable to many medical accelerators.« less

Application Of Optical Techniques To Command, Control, And Communications (C3) Systems

NASA Astrophysics Data System (ADS)

Weinberg, M.; Steensma, P. D.

1981-02-01

This paper identifies and discusses specific applications of the optical transmission technology to various Command Control and Communications (C3) systems. Candidate C3 systems will first be identified and discussed briefly. These will include: 407L/485L Tactical Air Defense Systems (USAF) TAOC-85 Tactical Air Operations Central (USMC) SACDIN Strategic Air Command Digital Integrated Network (USAF) MX-C3 Missile "X" Command Control Communications Network The first tr are classified as tactical C3 systems while the latter two are classified as strategic C systems. Potential optical applications will be identified along with the benefits derived. Each application will be discussed with key parameters, cost performance benefits, potential problem areas, time frame for development identified.

Electroplated targets for production of unique PET radionuclides

NASA Astrophysics Data System (ADS)

Bui, V.; Sheh, Y.; Finn, R.; Francesconi, L.; Cai, S.; Schlyer, D.; Wieland, B.

1995-12-01

The past decade has witnessed the applications of positron emission tomography (PET) evolving from a purely research endeavor to a procedure which has specific clinical applications in the areas of cardiology, neurology and oncology. The growth of PET has been facilitated by developments in both medical instrumentation and radiopharmaceutical chemistry efforts. Included in this latter effort has been the low energy accelerator production and processing of unique PET radionuclides appropriate for the radiolabeling of biomolecules, i.e. monoclonal antibodies and peptides. The development and application of electroplated targets of antimony and copper for the production of iodine-124 and gallium-66 respectively, utilizing the Memorial Sloan-Kettering Cancer Center (MSKCC) cyclotron are examples of target design and development applicable to many medical accelerators.

Treatment considerations in actinic keratosis.

PubMed

Goldenberg, G

2017-03-01

The chronic skin condition actinic keratosis (AK) is characterized by the formation of keratotic lesions of variable thickness that are poorly delimited. AK occurs on areas of the skin that have had long-term exposure to the sun or UV radiation. Although AKs may regress, they usually persist and can progress to squamous cell carcinoma (SCC). Clinicians are unable to predict which AKs will progress; therefore, both clinically visible lesions and subclinical, non-visible (i.e. the entire area affected by AK/field cancerization) should be treated. AK treatment options include lesion-directed therapies that target specific AK lesions and field-directed therapies that target multiple clinical lesions and the underlying field damage. This article reviews currently available treatment options in AK, with a focus on patient-applied field therapies, and their suitability according to specific disease characteristics and patient needs. Choice of treatment in AK depends on lesion-, patient- and treatment-related factors and should be individualized. Considerations when choosing a therapy include site of application, treatment duration, surface area of application, tolerability profiles and implications on adherence. Field-directed therapies treat clinical and subclinical damage (i.e. the entire area affected by AK), achieve high rates of sustained clearance of AKs and may reduce the risk of progression to SCC. There is a clear need for field therapies with short duration of treatment and predictable, short-lived, mild local skin reactions that can be used over a large surface area. Therapies with shorter and simpler treatment courses are often associated with better adherence than treatments with longer courses. These may, therefore, represent more appropriate choices in patients for whom convenience and/or adherence are an issue. © 2017 European Academy of Dermatology and Venereology.

Mine-hunting dolphins of the Navy

NASA Astrophysics Data System (ADS)

Moore, Patrick W.

1997-07-01

Current counter-mine and obstacle avoidance technology is inadequate, and limits the Navy's capability to conduct shallow water (SW) and very shallow water (VSW) MCM in support of beach assaults by Marine Corps forces. Without information as to the location or density of mined beach areas, it must be assumed that if mines are present in one area then they are present in all areas. Marine mammal systems (MMS) are an unusual, effective and unique solution to current problems of mine and obstacle hunting. In the US Navy Mine Warfare Plan for 1994-1995 Marine Mammal Systems are explicitly identified as the Navy's only means of countering buried mines and the best means for dealing with close-tethered mines. The dolphins in these systems possess a biological sonar specifically adapted for their shallow and very shallow water habitat. Research has demonstrated that the dolphin biosonar outperforms any current hardware system available for SW and VSW applications. This presentation will cover current Fleet MCM systems and future technology application to the littoral region.

Conceptual study of superconducting urban area power systems

NASA Astrophysics Data System (ADS)

Noe, Mathias; Bach, Robert; Prusseit, Werner; Willén, Dag; Gold-acker, Wilfried; Poelchau, Juri; Linke, Christian

2010-06-01

Efficient transmission, distribution and usage of electricity are fundamental requirements for providing citizens, societies and economies with essential energy resources. It will be a major future challenge to integrate more sustainable generation resources, to meet growing electricity demand and to renew electricity networks. Research and development on superconducting equipment and components have an important role to play in addressing these challenges. Up to now, most studies on superconducting applications in power systems have been concentrated on the application of specific devices like for example cables and current limiters. In contrast to this, the main focus of our study is to show the consequence of a large scale integration of superconducting power equipment in distribution level urban power systems. Specific objectives are to summarize the state-of-the-art of superconducting power equipment including cooling systems and to compare the superconducting power system with respect to energy and economic efficiency with conventional solutions. Several scenarios were considered starting from the replacement of an existing distribution level sub-grid up to a full superconducting urban area distribution level power system. One major result is that a full superconducting urban area distribution level power system could be cost competitive with existing solutions in the future. In addition to that, superconducting power systems offer higher energy efficiency as well as a number of technical advantages like lower voltage drops and improved stability.

Steady-state equation of water vapor sorption for CaCl2-based chemical sorbents and its application

PubMed Central

Zhang, Haiquan; Yuan, Yanping; Sun, Qingrong; Cao, Xiaoling; Sun, Liangliang

2016-01-01

Green CaCl2-based chemical sorbent has been widely used in sorption refrigeration, air purification and air desiccation. Methods to improve the sorption rate have been extensively investigated, but the corresponding theoretical formulations have not been reported. In this paper, a sorption system of solid-liquid coexistence is established based on the hypothesis of steady-state sorption. The combination of theoretical analysis and experimental results indicates that the system can be described by steady-state sorption process. The steady-state sorption equation, μ = (η − γT) , was obtained in consideration of humidity, temperature and the surface area. Based on engineering applications and this equation, two methods including an increase of specific surface area and adjustment of the critical relative humidity (γ) for chemical sorbents, have been proposed to increase the sorption rate. The results indicate that the CaCl2/CNTs composite with a large specific surface area can be obtained by coating CaCl2 powder on the surface of carbon nanotubes (CNTs). The composite reached sorption equilibrium within only 4 h, and the sorption capacity was improved by 75% compared with pure CaCl2 powder. Furthermore, the addition of NaCl powder to saturated CaCl2 solution could significantly lower the solution’s γ. The sorption rate was improved by 30% under the same environment. PMID:27682811

Steady-state equation of water vapor sorption for CaCl2-based chemical sorbents and its application

NASA Astrophysics Data System (ADS)

Zhang, Haiquan; Yuan, Yanping; Sun, Qingrong; Cao, Xiaoling; Sun, Liangliang

2016-09-01

Green CaCl2-based chemical sorbent has been widely used in sorption refrigeration, air purification and air desiccation. Methods to improve the sorption rate have been extensively investigated, but the corresponding theoretical formulations have not been reported. In this paper, a sorption system of solid-liquid coexistence is established based on the hypothesis of steady-state sorption. The combination of theoretical analysis and experimental results indicates that the system can be described by steady-state sorption process. The steady-state sorption equation, μ = (η - γT) , was obtained in consideration of humidity, temperature and the surface area. Based on engineering applications and this equation, two methods including an increase of specific surface area and adjustment of the critical relative humidity (γ) for chemical sorbents, have been proposed to increase the sorption rate. The results indicate that the CaCl2/CNTs composite with a large specific surface area can be obtained by coating CaCl2 powder on the surface of carbon nanotubes (CNTs). The composite reached sorption equilibrium within only 4 h, and the sorption capacity was improved by 75% compared with pure CaCl2 powder. Furthermore, the addition of NaCl powder to saturated CaCl2 solution could significantly lower the solution’s γ. The sorption rate was improved by 30% under the same environment.

Nationwide summary of US Geological Survey regional regression equations for estimating magnitude and frequency of floods for ungaged sites, 1993

USGS Publications Warehouse

Jennings, M.E.; Thomas, W.O.; Riggs, H.C.

1994-01-01

For many years, the U.S. Geological Survey (USGS) has been involved in the development of regional regression equations for estimating flood magnitude and frequency at ungaged sites. These regression equations are used to transfer flood characteristics from gaged to ungaged sites through the use of watershed and climatic characteristics as explanatory or predictor variables. Generally these equations have been developed on a statewide or metropolitan area basis as part of cooperative study programs with specific State Departments of Transportation or specific cities. The USGS, in cooperation with the Federal Highway Administration and the Federal Emergency Management Agency, has compiled all the current (as of September 1993) statewide and metropolitan area regression equations into a micro-computer program titled the National Flood Frequency Program.This program includes regression equations for estimating flood-peak discharges and techniques for estimating a typical flood hydrograph for a given recurrence interval peak discharge for unregulated rural and urban watersheds. These techniques should be useful to engineers and hydrologists for planning and design applications. This report summarizes the statewide regression equations for rural watersheds in each State, summarizes the applicable metropolitan area or statewide regression equations for urban watersheds, describes the National Flood Frequency Program for making these computations, and provides much of the reference information on the extrapolation variables needed to run the program.

[The monodigital recognition test (MRT)--a sensitivity-specific variant of Moberg's pick-up test].

PubMed

Clemens, R

1979-01-01

The Test for Mono-digital Recognition (MRT) is a procedure specifically designed for the measurement of gnostic performance. The new test was derived from MOBERG's Pick-up Test with the aim of eliminating its shortcomings. Additional injuries do not restrict the applicability of the MRT and the test is not confined to the skin area supplied by the median nerve. The MRT expresses the degree of gnostic disturbances by means of a point system. For testing a patient only two to four minutes are needed.

Development and Application of Integrated Optical Sensors for Intense E-Field Measurement

PubMed Central

Zeng, Rong; Wang, Bo; Niu, Ben; Yu, Zhanqing

2012-01-01

The measurement of intense E-fields is a fundamental need in various research areas. Integrated optical E-field sensors (IOESs) have important advantages and are potentially suitable for intense E-field detection. This paper comprehensively reviews the development and applications of several types of IOESs over the last 30 years, including the Mach-Zehnder interferometer (MZI), coupler interferometer (CI) and common path interferometer (CPI). The features of the different types of IOESs are compared, showing that the MZI has higher sensitivity, the CI has a controllable optical bias, and the CPI has better temperature stability. More specifically, the improvement work of applying IOESs to intense E-field measurement is illustrated. Finally, typical uses of IOESs in the measurement of intense E-fields are demonstrated, including application areas such as E-fields with different frequency ranges in high-voltage engineering, simulated nuclear electromagnetic pulse in high-power electromagnetic pulses, and ion-accelerating field in high-energy physics. PMID:23112663

Applications and Outreach for the Global Precipitation Measurement mission

NASA Astrophysics Data System (ADS)

Janney, D. W.; Kirschbaum, D.

2017-12-01

Too much or too little rain can serve as a tipping point for triggering catastrophic flooding and landslides or widespread drought. Knowing when, where and how much rain is falling globally is vital to understanding how people may be more or less impacted by disasters, the spread of water or vector-borne disease, or crop shortages. The Global Precipitation Measurement (GPM) mission provides near real-time precipitation data worldwide that is used by a broad range of end users, from tropical cyclone forecasters to agricultural modelers to researchers evaluating the spread of diseases. The GPM mission has an active applications and outreach program designed to engage and work closely with user communities across a broad spectrum of societal benefit areas with the goal of extending the application of GPM and other NASA data to support decision making. This presentation will outline some examples of how GPM has been engaging with the user community, highlighting some past and planned initiatives with specific organizations and across several thematic areas.

Development and Potential Applications of CRISPR-Cas9 Genome Editing Technology in Sarcoma

PubMed Central

Liu, Tang; Shen, Jacson K.; Li, Zhihong; Choy, Edwin; Hornicek, Francis J.; Duan, Zhenfeng

2016-01-01

Sarcomas include some of the most aggressive tumors and typically respond poorly to chemotherapy. In recent years, specific gene fusion/mutations and gene over-expression/activation have been shown to drive sarcoma pathogenesis and development. These emerging genomic alterations may provide targets for novel therapeutic strategies and have the potential to transform sarcoma patient care. The RNA-guided nuclease CRISPR-Cas9 (Clustered Regularly Interspaced Short Palindromic Repeats (CRISPR)-associated protein-9 nuclease) is a convenient and versatile platform for site-specific genome editing and epigenome targeted modulation. Given that sarcoma is believed to develop as a result of genetic alterations in mesenchymal progenitor/stem cells, CRISPR-Cas9 genome editing technologies hold extensive application potentials in sarcoma models and therapies. We review the development and mechanisms of the CRISPR-Cas9 system in genome editing and introduce its application in sarcoma research and potential therapy in clinic. Additionally, we propose future directions and discuss the challenges faced with these applications, providing concise and enlightening information for readers interested in this area. PMID:26806808

Development and potential applications of CRISPR-Cas9 genome editing technology in sarcoma.

PubMed

Liu, Tang; Shen, Jacson K; Li, Zhihong; Choy, Edwin; Hornicek, Francis J; Duan, Zhenfeng

2016-04-01

Sarcomas include some of the most aggressive tumors and typically respond poorly to chemotherapy. In recent years, specific gene fusion/mutations and gene over-expression/activation have been shown to drive sarcoma pathogenesis and development. These emerging genomic alterations may provide targets for novel therapeutic strategies and have the potential to transform sarcoma patient care. The RNA-guided nuclease CRISPR-Cas9 (Clustered Regularly Interspaced Short Palindromic Repeats (CRISPR)-associated protein-9 nuclease) is a convenient and versatile platform for site-specific genome editing and epigenome targeted modulation. Given that sarcoma is believed to develop as a result of genetic alterations in mesenchymal progenitor/stem cells, CRISPR-Cas9 genome editing technologies hold extensive application potentials in sarcoma models and therapies. We review the development and mechanisms of the CRISPR-Cas9 system in genome editing and introduce its application in sarcoma research and potential therapy in clinic. Additionally, we propose future directions and discuss the challenges faced with these applications, providing concise and enlightening information for readers interested in this area. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Application of wildfire spread and behavior models to assess fire probability and severity in the Mediterranean region

NASA Astrophysics Data System (ADS)

Salis, Michele; Arca, Bachisio; Bacciu, Valentina; Spano, Donatella; Duce, Pierpaolo; Santoni, Paul; Ager, Alan; Finney, Mark

2010-05-01

Characterizing the spatial pattern of large fire occurrence and severity is an important feature of the fire management planning in the Mediterranean region. The spatial characterization of fire probabilities, fire behavior distributions and value changes are key components for quantitative risk assessment and for prioritizing fire suppression resources, fuel treatments and law enforcement. Because of the growing wildfire severity and frequency in recent years (e.g.: Portugal, 2003 and 2005; Italy and Greece, 2007 and 2009), there is an increasing demand for models and tools that can aid in wildfire prediction and prevention. Newer wildfire simulation systems offer promise in this regard, and allow for fine scale modeling of wildfire severity and probability. Several new applications has resulted from the development of a minimum travel time (MTT) fire spread algorithm (Finney, 2002), that models the fire growth searching for the minimum time for fire to travel among nodes in a 2D network. The MTT approach makes computationally feasible to simulate thousands of fires and generate burn probability and fire severity maps over large areas. The MTT algorithm is imbedded in a number of research and fire modeling applications. High performance computers are typically used for MTT simulations, although the algorithm is also implemented in the FlamMap program (www.fire.org). In this work, we described the application of the MTT algorithm to estimate spatial patterns of burn probability and to analyze wildfire severity in three fire prone areas of the Mediterranean Basin, specifically Sardinia (Italy), Sicily (Italy) and Corsica (France) islands. We assembled fuels and topographic data for the simulations in 500 x 500 m grids for the study areas. The simulations were run using 100,000 ignitions under weather conditions that replicated severe and moderate weather conditions (97th and 70th percentile, July and August weather, 1995-2007). We used both random ignition locations and ignition probability grids (1000 x 1000 m) built from historical fire data (1995-2007). The simulation outputs were then examined to understand relationships between burn probability and specific vegetation types and ignition sources. Wildfire threats to specific values of human interest were quantified to map landscape patterns of wildfire risk. The simulation outputs also allowed us to differentiate between areas of the landscape that were progenitors of fires versus "victims" of large fires. The results provided spatially explicit data on wildfire likelihood and intensity that can be used in a variety of strategic and tactical planning forums to mitigate wildfire threats to human and other values in the Mediterranean Basin.

On Using a Mobile Application to Support Teledermatology: A Case Study in an Underprivileged Area in Colombia

PubMed Central

Novoa, Mónica Paola; Eapen, Bell Raj

2018-01-01

Background The use of mobile applications in dermatology to support remote diagnosis is gaining acceptance, particularly in rural areas, where dermatology services are commonly managed by healthcare personnel with no specialty training. Moreover, ontologies—sets of concepts that represent knowledge in a given domain—are increasingly being used to support medical diagnosis. A specific case is ONTODerm: an ontology to aid dermatological diagnosis. However, there is little information on the combined use of mobile applications and ontologies as support solutions in dermatology. Objective Assessing the reliability of ONTODerm as a tool to support remote dermatological diagnosis when used together with a mobile dermatological application in underprivileged areas. Methods A mobile application that allows characterization of skin lesions was developed, and the information about the lesions was sent to ONTODerm. An exploratory study was conducted in a remote area without access to a dermatologist. A total of 64 dermatological queries were recorded in the application and consulted with ONTODerm. Later, an experienced dermatologist evaluated the characterization and diagnosis of each query to determine the accuracy of the system. Results The results showed that the probability of obtaining a correct diagnosis was between 64.4% and 85.6% with a confidence interval of 95%. A higher accuracy rate was obtained when the skin lesion occurred on the face or when its border was categorized as poorly demarcated. Conclusions This study demonstrates the implementation of a teledermatology strategy based on mobile applications and domain ontology-driven knowledge base to provide timely assistance to healthcare professionals. This approach was found to be pertinent in the Colombian rural context, particularly in forest regions, where dermatology specialists are not available. The results of this article do not represent a final validation of the proposed approach; they suggest how the ontology can be improved to effectively support medical staff in marginalized regions. PMID:29785181

On Using a Mobile Application to Support Teledermatology: A Case Study in an Underprivileged Area in Colombia.

PubMed

Sáenz, Juan Pablo; Novoa, Mónica Paola; Correal, Darío; Eapen, Bell Raj

2018-01-01

The use of mobile applications in dermatology to support remote diagnosis is gaining acceptance, particularly in rural areas, where dermatology services are commonly managed by healthcare personnel with no specialty training. Moreover, ontologies-sets of concepts that represent knowledge in a given domain-are increasingly being used to support medical diagnosis. A specific case is ONTODerm: an ontology to aid dermatological diagnosis. However, there is little information on the combined use of mobile applications and ontologies as support solutions in dermatology. Assessing the reliability of ONTODerm as a tool to support remote dermatological diagnosis when used together with a mobile dermatological application in underprivileged areas. A mobile application that allows characterization of skin lesions was developed, and the information about the lesions was sent to ONTODerm. An exploratory study was conducted in a remote area without access to a dermatologist. A total of 64 dermatological queries were recorded in the application and consulted with ONTODerm. Later, an experienced dermatologist evaluated the characterization and diagnosis of each query to determine the accuracy of the system. The results showed that the probability of obtaining a correct diagnosis was between 64.4% and 85.6% with a confidence interval of 95%. A higher accuracy rate was obtained when the skin lesion occurred on the face or when its border was categorized as poorly demarcated. This study demonstrates the implementation of a teledermatology strategy based on mobile applications and domain ontology-driven knowledge base to provide timely assistance to healthcare professionals. This approach was found to be pertinent in the Colombian rural context, particularly in forest regions, where dermatology specialists are not available. The results of this article do not represent a final validation of the proposed approach; they suggest how the ontology can be improved to effectively support medical staff in marginalized regions.

Environmental Impacts of Large Scale Biochar Application Through Spatial Modeling

NASA Astrophysics Data System (ADS)

Huber, I.; Archontoulis, S.

2017-12-01

In an effort to study the environmental (emissions, soil quality) and production (yield) impacts of biochar application at regional scales we coupled the APSIM-Biochar model with the pSIMS parallel platform. So far the majority of biochar research has been concentrated on lab to field studies to advance scientific knowledge. Regional scale assessments are highly needed to assist decision making. The overall objective of this simulation study was to identify areas in the USA that have the most gain environmentally from biochar's application, as well as areas which our model predicts a notable yield increase due to the addition of biochar. We present the modifications in both APSIM biochar and pSIMS components that were necessary to facilitate these large scale model runs across several regions in the United States at a resolution of 5 arcminutes. This study uses the AgMERRA global climate data set (1980-2010) and the Global Soil Dataset for Earth Systems modeling as a basis for creating its simulations, as well as local management operations for maize and soybean cropping systems and different biochar application rates. The regional scale simulation analysis is in progress. Preliminary results showed that the model predicts that high quality soils (particularly those common to Iowa cropping systems) do not receive much, if any, production benefit from biochar. However, soils with low soil organic matter ( 0.5%) do get a noteworthy yield increase of around 5-10% in the best cases. We also found N2O emissions to be spatial and temporal specific; increase in some areas and decrease in some other areas due to biochar application. In contrast, we found increases in soil organic carbon and plant available water in all soils (top 30 cm) due to biochar application. The magnitude of these increases (% change from the control) were larger in soil with low organic matter (below 1.5%) and smaller in soils with high organic matter (above 3%) and also dependent on biochar application rate.

Export Control Requirements for Tritium Processing Design and R&D

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hollis, William Kirk; Maynard, Sarah-Jane Wadsworth

This document will address requirements of export control associated with tritium plant design and processes. Los Alamos National Laboratory has been working in the area of tritium plant system design and research and development (R&D) since the early 1970’s at the Tritium Systems Test Assembly (TSTA). This work has continued to the current date with projects associated with the ITER project and other Office of Science Fusion Energy Science (OS-FES) funded programs. ITER is currently the highest funding area for the DOE OS-FES. Although export control issues have been integrated into these projects in the past a general guidance documentmore » has not been available for reference in this area. To address concerns with currently funded tritium plant programs and assist future projects for FES, this document will identify the key reference documents and specific sections within related to tritium research. Guidance as to the application of these sections will be discussed with specific detail to publications and work with foreign nationals.« less

Nitrogen-doped ordered mesoporous carbon with a high surface area, synthesized through organic-inorganic coassembly, and its application in supercapacitors.

PubMed

Song, Yanfang; Li, Li; Wang, Yonggang; Wang, Congxiao; Guo, Zaipin; Xia, Yongyao

2014-07-21

A new nitrogen-doped ordered mesoporous carbon (N-doped OMC) is synthesized by using an organic-inorganic coassembly method, in which resol is used as the carbon precursor, dicyandiamide as the nitrogen precursor, silicate oligomers as the inorganic precursors, and F127 as the soft template. The N-doped OMC possesses a surface area as high as 1374 m(2)  g(-1) and a large pore size of 7.4 nm. As an electrode material for supercapacitors, the obtained carbon exhibits excellent cycling stability and delivers a reversible specific capacitance as high as 308 F g(-1) in 1 mol L(-1) H(2)SO(4) aqueous electrolyte, of which 58 % of the capacity is due to pseudo-capacitance. The large specific capacitance is attributed to proper pore size distributions, large surface area, and high nitrogen content. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Microwave-Assisted Synthesis of Highly-Crumpled, Few-Layered Graphene and Nitrogen-Doped Graphene for Use as High-Performance Electrodes in Capacitive Deionization

NASA Astrophysics Data System (ADS)

Amiri, Ahmad; Ahmadi, Goodarz; Shanbedi, Mehdi; Savari, Maryam; Kazi, S. N.; Chew, B. T.

2015-12-01

Capacitive deionization (CDI) is a promising procedure for removing various charged ionic species from brackish water. The performance of graphene-based material in capacitive deionization is lower than the expectation of the industry, so highly-crumpled, few-layered graphene (HCG) and highly-crumpled nitrogen-doped graphene (HCNDG) with high surface area have been introduced as promising candidates for CDI electrodes. Thus, HCG and HCNDG were prepared by exfoliation of graphite in the presence of liquid-phase, microwave-assisted methods. An industrially-scalable, cost-effective, and simple approach was employed to synthesize HCG and HCNDG, resulting in few-layered graphene and nitrogen-doped graphene with large specific surface area. Then, HCG and HCNDG were utilized for manufacturing a new class of carbon nanostructure-based electrodes for use in large-scale CDI equipment. The electrosorption results indicated that both the HCG and HCNDG have fairly large specific surface areas, indicating their huge potential for capacitive deionization applications.

Microwave-assisted synthesis of porous carbon-titania and highly crystalline titania nanostructures.

PubMed

Parker, Alison; Marszewski, Michal; Jaroniec, Mietek

2013-03-01

Porous carbon-titania and highly crystalline titania nanostructured materials were obtained through a microwave-assisted one-pot synthesis. Resorcinol and formaldehyde were used as carbon precursors, triblock copolymer Pluronic F127 as a stabilizing agent, and titanium isopropoxide as a titania precursor. This microwave-assisted one-pot synthesis involved formation of carbon spheres according to the recently modified Stöber method followed by hydrolysis and condensation of titania precursor. This method afforded carbon-titania composite materials containing anatase phase with specific surface areas as high as 390 m(2) g(-1). The pure nanostructured titania, obtained after removal of carbon through calcination of the composite material in air, was shown to be the anatase phase with considerably higher degree of crystallinity and the specific surface area as high as 130 m(2) g(-1). The resulting titania, because of its high surface area, well-developed porosity, and high crystallinity, is of great interest for catalysis, water treatment, lithium batteries, and other energy-related applications.

An application of almost marginal conditional stochastic dominance (AMCSD) on forming efficient portfolios

NASA Astrophysics Data System (ADS)

Slamet, Isnandar; Mardiana Putri Carissa, Siska; Pratiwi, Hasih

2017-10-01

Investors always seek an efficient portfolio which is a portfolio that has a maximum return on specific risk or minimal risk on specific return. Almost marginal conditional stochastic dominance (AMCSD) criteria can be used to form the efficient portfolio. The aim of this research is to apply the AMCSD criteria to form an efficient portfolio of bank shares listed in the LQ-45. This criteria is used when there are areas that do not meet the criteria of marginal conditional stochastic dominance (MCSD). On the other words, this criteria can be derived from quotient of areas that violate the MCSD criteria with the area that violate and not violate the MCSD criteria. Based on the data bank stocks listed on LQ-45, it can be stated that there are 38 efficient portfolios of 420 portfolios where each portfolio comprises of 4 stocks and 315 efficient portfolios of 1710 portfolios with each of portfolio has 3 stocks.

Export Control Requirements for Tritium Processing Design and R&D

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hollis, William Kirk; Maynard, Sarah-Jane Wadsworth

2015-10-30

This document will address requirements of export control associated with tritium plant design and processes. Los Alamos National Laboratory has been working in the area of tritium plant system design and research and development (R&D) since the early 1970’s at the Tritium Systems Test Assembly (TSTA). This work has continued to the current date with projects associated with the ITER project and other Office of Science Fusion Energy Science (OS-FES) funded programs. ITER is currently the highest funding area for the DOE OS-FES. Although export control issues have been integrated into these projects in the past a general guidance documentmore » has not been available for reference in this area. To address concerns with currently funded tritium plant programs and assist future projects for FES, this document will identify the key reference documents and specific sections within related to tritium research. Guidance as to the application of these sections will be discussed with specific detail to publications and work with foreign nationals.« less

High-Surface-Area Nitrogen-Doped Reduced Graphene Oxide for Electric Double-Layer Capacitors.

PubMed

Youn, Hee-Chang; Bak, Seong-Min; Kim, Myeong-Seong; Jaye, Cherno; Fischer, Daniel A; Lee, Chang-Wook; Yang, Xiao-Qing; Roh, Kwang Chul; Kim, Kwang-Bum

2015-06-08

A two-step method consisting of solid-state microwave irradiation and heat treatment under NH3 gas was used to prepare nitrogen-doped reduced graphene oxide (N-RGO) with a high specific surface area (1007 m(2)  g(-1) ), high electrical conductivity (1532 S m(-1) ), and low oxygen content (1.5 wt %) for electrical double-layer capacitor applications. The specific capacitance of N-RGO was 291 F g(-1) at a current density of 1 A g(-1) , and a capacitance of 261 F g(-1) was retained at 50 A g(-1) , which indicated a very good rate capability. N-RGO also showed excellent cycling stability and preserved 96 % of the initial specific capacitance after 100 000 cycles. Near-edge X-ray absorption fine-structure spectroscopy results provided evidenced for the recovery of π conjugation in the carbon networks with the removal of oxygenated groups and revealed chemical bonding of the nitrogen atoms in N-RGO. The good electrochemical performance of N-RGO is attributed to its high surface area, high electrical conductivity, and low oxygen content. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Popcorn-Derived Porous Carbon for Energy Storage and CO2 Capture.

PubMed

Liang, Ting; Chen, Chunlin; Li, Xing; Zhang, Jian

2016-08-16

Porous carbon materials have drawn tremendous attention due to its applications in energy storage, gas/water purification, catalyst support, and other important fields. However, producing high-performance carbons via a facile and efficient route is still a big challenge. Here we report the synthesis of microporous carbon materials by employing a steam-explosion method with subsequent potassium activation and carbonization of the obtained popcorn. The obtained carbon features a large specific surface area, high porosity, and doped nitrogen atoms. Using as an electrode material in supercapacitor, it displays a high specific capacitance of 245 F g(-1) at 0.5 A g(-1) and a remarkable stability of 97.8% retention after 5000 cycles at 5 A g(-1). The product also exhibits a high CO2 adsorption capacity of 4.60 mmol g(-1) under 1066 mbar and 25 °C. Both areal specific capacitance and specific CO2 uptake are directly proportional to the surface nitrogen content. This approach could thus enlighten the batch production of porous nitrogen-doped carbons for a wide range of energy and environmental applications.

Feature extraction for change analysis in SAR time series

NASA Astrophysics Data System (ADS)

Boldt, Markus; Thiele, Antje; Schulz, Karsten; Hinz, Stefan

2015-10-01

In remote sensing, the change detection topic represents a broad field of research. If time series data is available, change detection can be used for monitoring applications. These applications require regular image acquisitions at identical time of day along a defined period. Focusing on remote sensing sensors, radar is especially well-capable for applications requiring regularity, since it is independent from most weather and atmospheric influences. Furthermore, regarding the image acquisitions, the time of day plays no role due to the independence from daylight. Since 2007, the German SAR (Synthetic Aperture Radar) satellite TerraSAR-X (TSX) permits the acquisition of high resolution radar images capable for the analysis of dense built-up areas. In a former study, we presented the change analysis of the Stuttgart (Germany) airport. The aim of this study is the categorization of detected changes in the time series. This categorization is motivated by the fact that it is a poor statement only to describe where and when a specific area has changed. At least as important is the statement about what has caused the change. The focus is set on the analysis of so-called high activity areas (HAA) representing areas changing at least four times along the investigated period. As first step for categorizing these HAAs, the matching HAA changes (blobs) have to be identified. Afterwards, operating in this object-based blob level, several features are extracted which comprise shape-based, radiometric, statistic, morphological values and one context feature basing on a segmentation of the HAAs. This segmentation builds on the morphological differential attribute profiles (DAPs). Seven context classes are established: Urban, infrastructure, rural stable, rural unstable, natural, water and unclassified. A specific HA blob is assigned to one of these classes analyzing the CovAmCoh time series signature of the surrounding segments. In combination, also surrounding GIS information is included to verify the CovAmCoh based context assignment. In this paper, the focus is set on the features extracted for a later change categorization procedure.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Neumann, Scott; Britton, Jay; Devos, Arnold N.

There are many uses for the Common Information Model (CIM), an ontology that is being standardized through Technical Committee 57 of the International Electrotechnical Commission (IEC TC57). The most common uses to date have included application modeling, information exchanges, information management and systems integration. As one should expect, there are many issues that become apparent when the CIM ontology is applied to any one use. Some of these issues are shortcomings within the current draft of the CIM, and others are a consequence of the different ways in which the CIM can be applied using different technologies. As the CIMmore » ontology will and should evolve, there are several dangers that need to be recognized. One is overall consistency and impact upon applications when extending the CIM for a specific need. Another is that a tight coupling of the CIM to specific technologies could limit the value of the CIM in the longer term as an ontology, which becomes a larger issue over time as new technologies emerge. The integration of systems is one specific area of interest for application of the CIM ontology. This is an area dominated by the use of XML for the definition of messages. While this is certainly true when using Enterprise Application Integration (EAI) products, it is even more true with the movement towards the use of Web Services (WS), Service-Oriented Architectures (SOA) and Enterprise Service Buses (ESB) for integration. This general IT industry trend is consistent with trends seen within the IEC TC57 scope of power system management and associated information exchange. The challenge for TC57 is how to best leverage the CIM ontology using the various XML technologies and standards for integration. This paper will provide examples of how the CIM ontology is used and describe some specific issues that should be addressed within the CIM in order to increase its usefulness as an ontology. It will also describe some of the issues and challenges that will be faced as the CIM ontology is leveraged for integration purposes by IEC TC57 standards.« less

MODFLOW-LGR: Practical application to a large regional dataset

NASA Astrophysics Data System (ADS)

Barnes, D.; Coulibaly, K. M.

2011-12-01

In many areas of the US, including southwest Florida, large regional-scale groundwater models have been developed to aid in decision making and water resources management. These models are subsequently used as a basis for site-specific investigations. Because the large scale of these regional models is not appropriate for local application, refinement is necessary to analyze the local effects of pumping wells and groundwater related projects at specific sites. The most commonly used approach to date is Telescopic Mesh Refinement or TMR. It allows the extraction of a subset of the large regional model with boundary conditions derived from the regional model results. The extracted model is then updated and refined for local use using a variable sized grid focused on the area of interest. MODFLOW-LGR, local grid refinement, is an alternative approach which allows model discretization at a finer resolution in areas of interest and provides coupling between the larger "parent" model and the locally refined "child." In the present work, these two approaches are tested on a mining impact assessment case in southwest Florida using a large regional dataset (The Lower West Coast Surficial Aquifer System Model). Various metrics for performance are considered. They include: computation time, water balance (as compared to the variable sized grid), calibration, implementation effort, and application advantages and limitations. The results indicate that MODFLOW-LGR is a useful tool to improve local resolution of regional scale models. While performance metrics, such as computation time, are case-dependent (model size, refinement level, stresses involved), implementation effort, particularly when regional models of suitable scale are available, can be minimized. The creation of multiple child models within a larger scale parent model makes it possible to reuse the same calibrated regional dataset with minimal modification. In cases similar to the Lower West Coast model, where a model is larger than optimal for direct application as a parent grid, a combination of TMR and LGR approaches should be used to develop a suitable parent grid.

Fabrication of highly ordered polyaniline nanocone on pristine graphene for high-performance supercapacitor electrodes

NASA Astrophysics Data System (ADS)

Song, Ningning; Wang, Wucong; Wu, Yue; Xiao, Ding; Zhao, Yaping

2018-04-01

The hybrids of pristine graphene with polyaniline were synthesized by in situ polymerizations for making a high-performance supercapacitor. The formed high-ordered PANI nanocones were vertically aligned on the graphene sheets. The length of the PANI nanocones increased with the concentration of aniline monomer. The specific capacitance of the hybrids electrode in the three-electrode system was measured as high as 481 F/g at a current density of 0.1 A/g, and its stability remained 87% after constant charge-discharge 10000 cycles at a current density of 1 A/g. This outstanding performance is attributed to the coupling effects of the pristine graphene and the hierarchical structure of the PANI possessing high specific surface area. The unique structure of the PANI provided more charge transmission pathways and fast charge-transfer speed of electrons to the pristine graphene because of its large specific area exposed to the electrolyte. The hybrid is expected to have potential applications in supercapacitor electrodes.

Micro- and nano-hydroxyapatite as active reinforcement for soft biocomposites.

PubMed

Munarin, F; Petrini, P; Gentilini, R; Pillai, R S; Dirè, S; Tanzi, M C; Sglavo, V M

2015-01-01

Pectin-based biocomposite hydrogels were produced by internal gelation, using different hydroxyapatite (HA) powders from commercial source or synthesized by the wet chemical method. HA possesses the double functionality of cross-linking agent and inorganic reinforcement. The mineralogical composition, grain size, specific surface area and microstructure of the hydroxyapatite powders are shown to strongly influence the properties of the biocomposites. Specifically, the grain size and specific surface area of the HA powders are strictly correlated to the gelling time and rheological properties of the hydrogels at room temperature. Pectin pH is also significant for the formation of ionic cross-links and therefore for the hydrogels stability at higher temperatures. The obtained results point out that micrometric-size hydroxyapatite can be proposed for applications which require rapid gelling kinetics and improved mechanical properties; conversely the nanometric hydroxyapatite synthesized in the present work seems the best choice to obtain homogeneous hydrogels with more easily controlled gelling kinetics. Copyright © 2014 Elsevier B.V. All rights reserved.

Digital micromirror based near-infrared illumination system for plasmonic photothermal neuromodulation.

PubMed

Jung, Hyunjun; Kang, Hongki; Nam, Yoonkey

2017-06-01

Light-mediated neuromodulation techniques provide great advantages to investigate neuroscience due to its high spatial and temporal resolution. To generate a spatial pattern of neural activity, it is necessary to develop a system for patterned-light illumination to a specific area. Digital micromirror device (DMD) based patterned illumination system have been used for neuromodulation due to its simple configuration and design flexibility. In this paper, we developed a patterned near-infrared (NIR) illumination system for region specific photothermal manipulation of neural activity using NIR-sensitive plasmonic gold nanorods (GNRs). The proposed system had high power transmission efficiency for delivering power density up to 19 W/mm 2 . We used a GNR-coated microelectrode array (MEA) to perform biological experiments using E18 rat hippocampal neurons and showed that it was possible to inhibit neural spiking activity of specific area in neural circuits with the patterned NIR illumination. This patterned NIR illumination system can serve as a promising neuromodulation tool to investigate neuroscience in a wide range of physiological and clinical applications.

A Study of Carbon Nanofibers and Active Carbon as Symmetric Supercapacitor in Aqueous Electrolyte: A Comparative Study

NASA Astrophysics Data System (ADS)

Daraghmeh, Allan; Hussain, Shahzad; Saadeddin, Iyad; Servera, Llorenç; Xuriguera, Elena; Cornet, Albert; Cirera, Albert

2017-12-01

Symmetric supercapacitors are fabricated by carbon nanofibers (CNF) and activated carbon (AC) using similar proportions of 7 wt% polyvinylidene fluoride (PVDF) polymer binder in an aqueous electrolyte. In this study, a comparison of porous texture and electrochemical performances between CNFs and AC based supercapacitors was carried out. Electrodes were assembled in the cell without a current collector. The prepared electrodes of CNFs and AC present Brunauer-Emmett-Teller (BET) surface area of 83 and 1042 m2/g, respectively. The dominant pore structure for CNFs is mesoporous while for AC is micropore. The results showed that AC provided higher specific capacitance retention up to very fast scan rate of 500 mV/s. AC carbon had a specific capacitance of 334 F/g, and CNFs had 52 F/g at scan rate 5 mV/s in aqueous solution. Also, the results indicate the superior conductivity of CNFs in contrast to AC counterparts. The measured equivalent series resistance (ESR) showed a very small value for CNFs (0.28 Ω) in comparison to AC that has an ESR resistance of (3.72 Ω). Moreover, CNF delivered higher specific power (1860 W/kg) than that for AC (450 W/kg). On the other hand, AC gave higher specific energy (18.1 Wh/kg) than that for CNFs (2 Wh/kg).This indicates that the AC is good for energy applications. Whereas, CNF is good for power application. Indeed, the higher surface area will lead to higher specific capacitance and hence higher energy density for AC. For CNF, lower ESR is responsible for having higher power density. Both CNF and AC supercapacitor exhibit an excellent charge-discharge stability up to 2500 cycles.

Standardization of whole slide image morphologic assessment with definition of a new application: Digital slide dynamic morphometry.

PubMed

Puppa, Giacomo; Risio, Mauro; Sheahan, Kieran; Vieth, Michael; Zlobec, Inti; Lugli, Alessandro; Pecori, Sara; Wang, Lai Mun; Langner, Cord; Mitomi, Hiroyuki; Nakamura, Takatoshi; Watanabe, Masahiko; Ueno, Hideki; Chasle, Jacques; Senore, Carlo; Conley, Stephen A; Herlin, Paulette; Lauwers, Gregory Y

2011-01-01

In histopathology, the quantitative assessment of various morphologic features is based on methods originally conceived on specific areas observed through the microscope used. Failure to reproduce the same reference field of view using a different microscope will change the score assessed. Visualization of a digital slide on a screen through a dedicated viewer allows selection of the magnification. However, the field of view is rectangular, unlike the circular field of optical microscopy. In addition, the size of the selected area is not evident, and must be calculated. A digital slide morphometric system was conceived to reproduce the various methods published for assessing tumor budding in colorectal cancer. Eighteen international experts in colorectal cancer were invited to participate in a web-based study by assessing tumor budding with five different methods in 100 digital slides. The specific areas to be tested by each method were marked by colored circles. The areas were grouped in a target-like pattern and then saved as an .xml file. When a digital slide was opened, the .xml file was imported in order to perform the measurements. Since the morphometric tool is composed of layers that can be freely moved on top of the digital slide, the technique was named digital slide dynamic morphometry. Twelve investigators completed the task, the majority of them performing the multiple evaluations of each of the cases in less than 12 minutes. Digital slide dynamic morphometry has various potential applications and might be a useful tool for the assessment of histologic parameters originally conceived for optical microscopy that need to be quantified.

Influence of wetting effect at the outer surface of the pipe on increase in leak rate - experimental results and discussion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Isozaki, Toshikuni; Shibata, Katsuyuki

1997-04-01

Experimental and computed results applicable to Leak Before Break analysis are presented. The specific area of investigation is the effect of the temperature distribution changes due to wetting of the test pipe near the crack on the increase in the crack opening area and leak rate. Two 12-inch straight pipes subjected to both internal pressure and thermal load, but not to bending load, are modelled. The leak rate was found to be very susceptible to the metal temperature of the piping. In leak rate tests, therefore, it is recommended that temperature distribution be measured precisely for a wide area.

Experiences of Structured Elicitation for Model-Based Cost-Effectiveness Analyses.

PubMed

Soares, Marta O; Sharples, Linda; Morton, Alec; Claxton, Karl; Bojke, Laura

2018-06-01

Empirical evidence supporting the cost-effectiveness estimates of particular health care technologies may be limited, or it may even be missing entirely. In these situations, additional information, often in the form of expert judgments, is needed to reach a decision. There are formal methods to quantify experts' beliefs, termed as structured expert elicitation (SEE), but only limited research is available in support of methodological choices. Perhaps as a consequence, the use of SEE in the context of cost-effectiveness modelling is limited. This article reviews applications of SEE in cost-effectiveness modelling with the aim of summarizing the basis for methodological choices made in each application and recording the difficulties and challenges reported by the authors in the design, conduct, and analyses. The methods used in each application were extracted along with the criteria used to support methodological and practical choices and any issues or challenges discussed in the text. Issues and challenges were extracted using an open field, and then categorised and grouped for reporting. The review demonstrates considerable heterogeneity in methods used, and authors acknowledge great methodological uncertainty in justifying their choices. Specificities of the context area emerging as potentially important in determining further methodological research in elicitation are between- expert variation and its interpretation, the fact that substantive experts in the area may not be trained in quantitative subjects, that judgments are often needed on various parameter types, the need for some form of assessment of validity, and the need for more integration with behavioural research to devise relevant debiasing strategies. This review of experiences of SEE highlights a number of specificities/constraints that can shape the development of guidance and target future research efforts in this area. Copyright © 2018 International Society for Pharmacoeconomics and Outcomes Research (ISPOR). Published by Elsevier Inc. All rights reserved.

Nanowire modified carbon fibers for enhanced electrical energy storage

NASA Astrophysics Data System (ADS)

Shuvo, Mohammad Arif Ishtiaque; (Bill) Tseng, Tzu-Liang; Ashiqur Rahaman Khan, Md.; Karim, Hasanul; Morton, Philip; Delfin, Diego; Lin, Yirong

2013-09-01

The study of electrochemical super-capacitors has become one of the most attractive topics in both academia and industry as energy storage devices because of their high power density, long life cycles, and high charge/discharge efficiency. Recently, there has been increasing interest in the development of multifunctional structural energy storage devices such as structural super-capacitors for applications in aerospace, automobiles, and portable electronics. These multifunctional structural super-capacitors provide structures combining energy storage and load bearing functionalities, leading to material systems with reduced volume and/or weight. Due to their superior materials properties, carbon fiber composites have been widely used in structural applications for aerospace and automotive industries. Besides, carbon fiber has good electrical conductivity which will provide lower equivalent series resistance; therefore, it can be an excellent candidate for structural energy storage applications. Hence, this paper is focused on performing a pilot study for using nanowire/carbon fiber hybrids as building materials for structural energy storage materials; aiming at enhancing the charge/discharge rate and energy density. This hybrid material combines the high specific surface area of carbon fiber and pseudo-capacitive effect of metal oxide nanowires, which were grown hydrothermally in an aligned fashion on carbon fibers. The aligned nanowire array could provide a higher specific surface area that leads to high electrode-electrolyte contact area thus fast ion diffusion rates. Scanning Electron Microscopy and X-Ray Diffraction measurements are used for the initial characterization of this nanowire/carbon fiber hybrid material system. Electrochemical testing is performed using a potentio-galvanostat. The results show that gold sputtered nanowire carbon fiber hybrid provides 65.9% higher energy density than bare carbon fiber cloth as super-capacitor.

Patient-specific bone modeling and analysis: the role of integration and automation in clinical adoption.

PubMed

Zadpoor, Amir A; Weinans, Harrie

2015-03-18

Patient-specific analysis of bones is considered an important tool for diagnosis and treatment of skeletal diseases and for clinical research aimed at understanding the etiology of skeletal diseases and the effects of different types of treatment on their progress. In this article, we discuss how integration of several important components enables accurate and cost-effective patient-specific bone analysis, focusing primarily on patient-specific finite element (FE) modeling of bones. First, the different components are briefly reviewed. Then, two important aspects of patient-specific FE modeling, namely integration of modeling components and automation of modeling approaches, are discussed. We conclude with a section on validation of patient-specific modeling results, possible applications of patient-specific modeling procedures, current limitations of the modeling approaches, and possible areas for future research. Copyright © 2014 Elsevier Ltd. All rights reserved.

Tuning the porosity of mesoporous NiO through calcining isostructural Ni-MOFs toward supercapacitor applications

NASA Astrophysics Data System (ADS)

Hou, Xiang-Yang; Yan, Xiao-Li; Wang, Xiao; Zhai, Quan-Guo

2018-07-01

NiO has an unusually high theoretical specific capacitance and possess relatively high electrical conductivity compared to other metal oxides. However, the reported specific capacitance of the NiO-based electrodes is far below the theoretical value up to now. In this paper, three porous NiO materials with different specific surface area were synthesized simply by calcining iso-structural Ni-based MOFs templates. The formation mechanism of NiO was discussed by taking into account the thermal behavior and intrinsic structural features of the Ni-MOFs. Taking advantages of the Ni-MOFs precursors, all prepared NiO compounds are mesoporous and their porosity can be tuned by the structure of MOFs. Specially, due to the high porosity, three NiO exhibited an improved electrochemical performance and the specific discharge capacitances are of 102, 105, and 116 F g-1 at the current density of 1 A g-1, respectively. The specific capacitance of 1-NiO-450 is approximately 93.2% of its maximum value after 3000 cycles, which obviously superior to most of the previously reported NiO electrode materials and suggests their promising applications in supercapacitors.

Semantics-based distributed I/O with the ParaMEDIC framework.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Balaji, P.; Feng, W.; Lin, H.

2008-01-01

Many large-scale applications simultaneously rely on multiple resources for efficient execution. For example, such applications may require both large compute and storage resources; however, very few supercomputing centers can provide large quantities of both. Thus, data generated at the compute site oftentimes has to be moved to a remote storage site for either storage or visualization and analysis. Clearly, this is not an efficient model, especially when the two sites are distributed over a wide-area network. Thus, we present a framework called 'ParaMEDIC: Parallel Metadata Environment for Distributed I/O and Computing' which uses application-specific semantic information to convert the generatedmore » data to orders-of-magnitude smaller metadata at the compute site, transfer the metadata to the storage site, and re-process the metadata at the storage site to regenerate the output. Specifically, ParaMEDIC trades a small amount of additional computation (in the form of data post-processing) for a potentially significant reduction in data that needs to be transferred in distributed environments.« less

Diffusion coefficient of hydrogen in a cast gamma titanium aluminide

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sundaram, P.A.; Wessel, E.; Ennis, P.J.

1999-06-04

Gamma titanium aluminides have the potential for high temperature applications because of their high specific strength and specific modulus. Their oxidation resistance is good, especially at intermediate temperatures and with suitable alloying additions, good oxidation resistance can be obtained up to 800 C. One critical area of application is in combustion engines in aero-space vehicles such as hypersonic airplanes and high speed civil transport airplanes. This entails the use of hydrogen as a fuel component and hence the effect of hydrogen on the mechanical properties of gamma titanium aluminides is of significant scientific and technological utility. The purpose of thismore » short investigation is to use an electrochemical method under galvanostatic conditions to determine the diffusion coefficient of hydrogen in a cast gamma titanium aluminide, a typical technical alloy with potential application in gas turbines under creep conditions. This result will be then compared with that obtained by microhardness profiling of electrolytically hydrogen precharged material.« less

Assessment of the State of the Art of Flight Control Technologies as Applicable to Adverse Conditions

NASA Technical Reports Server (NTRS)

Reveley, Mary s.; Briggs, Jeffrey L.; Leone, Karen M.; Kurtoglu, Tolga; Withrow, Colleen A.

2010-01-01

Literature from academia, industry, and other Government agencies was surveyed to assess the state of the art in current Integrated Resilient Aircraft Control (IRAC) aircraft technologies. Over 100 papers from 25 conferences from the time period 2004 to 2009 were reviewed. An assessment of the general state of the art in adaptive flight control is summarized first, followed by an assessment of the state of the art as applicable to 13 identified adverse conditions. Specific areas addressed in the general assessment include flight control when compensating for damage or reduced performance, retrofit software upgrades to flight controllers, flight control through engine response, and finally test and validation of new adaptive controllers. The state-of-the-art assessment applicable to the adverse conditions include technologies not specifically related to flight control, but may serve as inputs to a future flight control algorithm. This study illustrates existing gaps and opportunities for additional research by the NASA IRAC Project

Principles, Techniques, and Applications of Tissue Microfluidics

NASA Technical Reports Server (NTRS)

Wade, Lawrence A.; Kartalov, Emil P.; Shibata, Darryl; Taylor, Clive

2011-01-01

The principle of tissue microfluidics and its resultant techniques has been applied to cell analysis. Building microfluidics to suit a particular tissue sample would allow the rapid, reliable, inexpensive, highly parallelized, selective extraction of chosen regions of tissue for purposes of further biochemical analysis. Furthermore, the applicability of the techniques ranges beyond the described pathology application. For example, they would also allow the posing and successful answering of new sets of questions in many areas of fundamental research. The proposed integration of microfluidic techniques and tissue slice samples is called "tissue microfluidics" because it molds the microfluidic architectures in accordance with each particular structure of each specific tissue sample. Thus, microfluidics can be built around the tissues, following the tissue structure, or alternatively, the microfluidics can be adapted to the specific geometry of particular tissues. By contrast, the traditional approach is that microfluidic devices are structured in accordance with engineering considerations, while the biological components in applied devices are forced to comply with these engineering presets.

Cross-cutting High Surface Area Graphene-based Frameworks with Controlled Pore Structure/Dopants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gaillard, J.

The goal of this project is to enhance the performance of graphene-based materials by manufacturing specific 3D architectures. The materials have global applications regarding fuel cell catalysts, gas adsorbents, supercapacitor/battery electrodes, ion (e.g., actinide) capture, gas separation, oil adsorption, and catalysis. This research focuses on hydrogen storage for hydrogen fuel cell vehicles with a potential transformational impact on hydrogen adsorbents that exhibit high gravimetric and volumetric density, a clean energy application sought by the Department of Energy. The development of an adsorbent material would enable broad commercial opportunities in hydrogen-fueled vehicles, promote new advanced nanomanufacturing scale-up, and open other opportunitiesmore » at Savannah River National Laboratory to utilize a high surface area material that is robust, chemically stable, and radiation resistant.« less

Localised estimates and spatial mapping of poverty incidence in the state of Bihar in India—An application of small area estimation techniques

PubMed Central

Aditya, Kaustav; Sud, U. C.

2018-01-01

Poverty affects many people, but the ramifications and impacts affect all aspects of society. Information about the incidence of poverty is therefore an important parameter of the population for policy analysis and decision making. In order to provide specific, targeted solutions when addressing poverty disadvantage small area statistics are needed. Surveys are typically designed and planned to produce reliable estimates of population characteristics of interest mainly at higher geographic area such as national and state level. Sample sizes are usually not large enough to provide reliable estimates for disaggregated analysis. In many instances estimates are required for areas of the population for which the survey providing the data was unplanned. Then, for areas with small sample sizes, direct survey estimation of population characteristics based only on the data available from the particular area tends to be unreliable. This paper describes an application of small area estimation (SAE) approach to improve the precision of estimates of poverty incidence at district level in the State of Bihar in India by linking data from the Household Consumer Expenditure Survey 2011–12 of NSSO and the Population Census 2011. The results show that the district level estimates generated by SAE method are more precise and representative. In contrast, the direct survey estimates based on survey data alone are less stable. PMID:29879202

Localised estimates and spatial mapping of poverty incidence in the state of Bihar in India-An application of small area estimation techniques.

PubMed

Chandra, Hukum; Aditya, Kaustav; Sud, U C

2018-01-01

Poverty affects many people, but the ramifications and impacts affect all aspects of society. Information about the incidence of poverty is therefore an important parameter of the population for policy analysis and decision making. In order to provide specific, targeted solutions when addressing poverty disadvantage small area statistics are needed. Surveys are typically designed and planned to produce reliable estimates of population characteristics of interest mainly at higher geographic area such as national and state level. Sample sizes are usually not large enough to provide reliable estimates for disaggregated analysis. In many instances estimates are required for areas of the population for which the survey providing the data was unplanned. Then, for areas with small sample sizes, direct survey estimation of population characteristics based only on the data available from the particular area tends to be unreliable. This paper describes an application of small area estimation (SAE) approach to improve the precision of estimates of poverty incidence at district level in the State of Bihar in India by linking data from the Household Consumer Expenditure Survey 2011-12 of NSSO and the Population Census 2011. The results show that the district level estimates generated by SAE method are more precise and representative. In contrast, the direct survey estimates based on survey data alone are less stable.

A Review of Agents for Palliative Sedation/Continuous Deep Sedation: Pharmacology and Practical Applications.

PubMed

Bodnar, John

2017-03-01

Continuous deep sedation at the end of life is a specific form of palliative sedation requiring a care plan that essentially places and maintains the patient in an unresponsive state because their symptoms are refractory to any other interventions. Because this application is uncommon, many providers may lack practical experience in this specialized area and resources they can access are outdated, nonspecific, and/or not comprehensive. The purpose of this review is to provide an evidence- and experience-based reference that specifically addresses those medications and regimens and their practical applications for this very narrow, but vital, aspect of hospice care. Patient goals in a hospital and hospice environments are different, so the manner in which widely used sedatives are dosed and applied can differ greatly as well. Parameters applied in end-of-life care that are based on experience and a thorough understanding of the pharmacology of those medications will differ from those applied in an intensive care unit or other medical environments. By recognizing these different goals and applying well-founded regimens geared specifically for end-of-life sedation, we can address our patients' symptoms in a more timely and efficacious manner.

A multicriteria-based methodology for site prioritisation in sediment management.

PubMed

Alvarez-Guerra, Manuel; Viguri, Javier R; Voulvoulis, Nikolaos

2009-08-01

Decision-making for sediment management is a complex task that incorporates the selections of areas for remediation and the assessment of options for any mitigation required. The application of Multicriteria Analysis (MCA) to rank different areas, according to their need for sediment management, provides a great opportunity for prioritisation, a first step in an integrated methodology that finally aims to assess and select suitable alternatives for managing the identified priority sites. This paper develops a methodology that starts with the delimitation of management units within areas of study, followed by the application of MCA methods that allows ranking of these management units, according to their need for remediation. This proposed process considers not only scientific evidence on sediment quality, but also other relevant aspects such as social and economic criteria associated with such decisions. This methodology is illustrated with its application to the case study area of the Bay of Santander, in northern Spain, highlighting some of the implications of utilising different MCA methods in the process. It also uses site-specific data to assess the subjectivity in the decision-making process, mainly reflected through the assignment of the criteria weights and uncertainties in the criteria scores. Analysis of the sensitivity of the results to these factors is used as a way to assess the stability and robustness of the ranking as a first step of the sediment management decision-making process.

Nanotechnology in the targeted drug delivery for bone diseases and bone regeneration

PubMed Central

Gu, Wenyi; Wu, Chengtie; Chen, Jiezhong; Xiao, Yin

2013-01-01

Nanotechnology is a vigorous research area and one of its important applications is in biomedical sciences. Among biomedical applications, targeted drug delivery is one of the most extensively studied subjects. Nanostructured particles and scaffolds have been widely studied for increasing treatment efficacy and specificity of present treatment approaches. Similarly, this technique has been used for treating bone diseases including bone regeneration. In this review, we have summarized and highlighted the recent advancement of nanostructured particles and scaffolds for the treatment of cancer bone metastasis, osteosarcoma, bone infections and inflammatory diseases, osteoarthritis, as well as for bone regeneration. Nanoparticles used to deliver deoxyribonucleic acid and ribonucleic acid molecules to specific bone sites for gene therapies are also included. The investigation of the implications of nanoparticles in bone diseases have just begun, and has already shown some promising potential. Further studies have to be conducted, aimed specifically at assessing targeted delivery and bioactive scaffolds to further improve their efficacy before they can be used clinically. PMID:23836972

Nanotechnology in the targeted drug delivery for bone diseases and bone regeneration.

PubMed

Gu, Wenyi; Wu, Chengtie; Chen, Jiezhong; Xiao, Yin

2013-01-01

Nanotechnology is a vigorous research area and one of its important applications is in biomedical sciences. Among biomedical applications, targeted drug delivery is one of the most extensively studied subjects. Nanostructured particles and scaffolds have been widely studied for increasing treatment efficacy and specificity of present treatment approaches. Similarly, this technique has been used for treating bone diseases including bone regeneration. In this review, we have summarized and highlighted the recent advancement of nanostructured particles and scaffolds for the treatment of cancer bone metastasis, osteosarcoma, bone infections and inflammatory diseases, osteoarthritis, as well as for bone regeneration. Nanoparticles used to deliver deoxyribonucleic acid and ribonucleic acid molecules to specific bone sites for gene therapies are also included. The investigation of the implications of nanoparticles in bone diseases have just begun, and has already shown some promising potential. Further studies have to be conducted, aimed specifically at assessing targeted delivery and bioactive scaffolds to further improve their efficacy before they can be used clinically.

Visualizing and communicating climate change using the ClimateWizard: decision support and education through web-based analysis and mapping

NASA Astrophysics Data System (ADS)

Girvetz, E. H.; Zganjar, C.; Raber, G. T.; Maurer, E. P.; Duffy, P.

2009-12-01

Virtually all fields of study and parts of society—from ecological science and nature conservation, to global development, multinational corporations, and government bodies—need to know how climate change has and may impact specific locations of interest. Our ability to respond to climate change depends on having convenient tools that make past and projected climate trends available to planners, managers, scientists and the general public, at scales ranging from global to local scales. Web-mapping applications provide an effective platform for communicating climate change impacts in specific geographic areas of interest to the public. Here, we present one such application, the ClimateWizard, that allows users to analyze, visualize and explore climate change maps for specific geographic areas of interest throughout the world (http://ClimateWizard.org). Built on Web 2.0 web-services (SOAP), Google Maps mash-up, and cloud computing technologies, the ClimateWizard analyzes large databases of climate information located on remote servers to create synthesized information and useful products tailored to geographic areas of interest (e.g. maps, graphs, tables, GIS layers). We demonstrate how the ClimateWizard can be used to assess projected changes to temperature and precipitation across all states in the contiguous United States and all countries of the world using statistically downscaled general circulation models from the CMIP3 dataset. We then go on to show how ClimateWizard can be used to analyze changes to other climate related variables, such as moisture stress and water production. Finally, we discuss how this tool can be adapted to develop a wide range of web-based tools that are targeted at informing specific audiences—from scientific research and natural resource management, to K-12 and higher education—about how climate change may affect different aspects of human and natural systems.

Comparison of two different artificial neural networks for prostate biopsy indication in two different patient populations.

PubMed

Stephan, Carsten; Xu, Chuanliang; Finne, Patrik; Cammann, Henning; Meyer, Hellmuth-Alexander; Lein, Michael; Jung, Klaus; Stenman, Ulf-Hakan

2007-09-01

Different artificial neural networks (ANNs) using total prostate-specific antigen (PSA) and percentage of free PSA (%fPSA) have been introduced to enhance the specificity of prostate cancer detection. The applicability of independently trained ANN and logistic regression (LR) models to different populations regarding the composition (screening versus referred) and different PSA assays has not yet been tested. Two ANN and LR models using PSA (range 4 to 10 ng/mL), %fPSA, prostate volume, digital rectal examination findings, and patient age were tested. A multilayer perceptron network (MLP) was trained on 656 screening participants (Prostatus PSA assay) and another ANN (Immulite-based ANN [iANN]) was constructed on 606 multicentric urologically referred men. These and other assay-adapted ANN models, including one new iANN-based ANN, were used. The areas under the curve for the iANN (0.736) and MLP (0.745) were equal but showed no differences to %fPSA (0.725) in the Finnish group. Only the new iANN-based ANN reached a significant larger area under the curve (0.77). At 95% sensitivity, the specificities of MLP (33%) and the new iANN-based ANN (34%) were significantly better than the iANN (23%) and %fPSA (19%). Reverse methodology using the MLP model on the referred patients revealed, in contrast, a significant improvement in the areas under the curve for iANN and MLP (each 0.83) compared with %fPSA (0.70). At 90% and 95% sensitivity, the specificities of all LR and ANN models were significantly greater than those for %fPSA. The ANNs based on different PSA assays and populations were mostly comparable, but the clearly different patient composition also allowed with assay adaptation no unbiased ANN application to the other cohort. Thus, the use of ANNs in other populations than originally built is possible, but has limitations.

Computer Assisted Instruction: A Review of the Reviews. Research Report 85-01.

ERIC Educational Resources Information Center

Stennett, R. G.

This review of the literature on computer assisted instruction (CAI) focuses on the use of CAI with grades K-13, and specifically assesses the relative merits of traditional instruction and CAI in promoting student achievement. Also assessed are the applications of CAI in the area of special education. Three types of reviews are used exclusively:…

Lithographically defined microporous carbon structures

DOEpatents

Burckel, David Bruce; Washburn, Cody M.; Polsky, Ronen; Brozik, Susan M.; Wheeler, David R.

2013-01-08

A lithographic method is used to fabricate porous carbon structures that can provide electrochemical electrodes having high surface area with uniform and controllable dimensions, providing enormous flexibility to tailor the electrodes toward specific applications. Metal nanoparticles deposited on the surface of the porous carbon electrodes exhibit ultra small dimensions with uniform size distribution. The resulting electrodes are rugged, electrically conductive and show excellent electrochemical behavior.

Teaching Clinical (and Nonclinical) Psychology through Applications to the Legal System: Violence Risk Assessment and the Insanity Defense

ERIC Educational Resources Information Center

Costanzo, Marina L.; Costanzo, Mark A.

2013-01-01

The prediction of dangerousness and the insanity defense are two areas where psychologists provide research-based expertise to the courts. Teachers of psychology can use these topics to capture the attention of students and to show how psychological research and theory can inform and influence the legal system. Specifically, teachers can use the…

Application of Risk Management and Uncertainty Concepts and Methods for Ecosystem Restoration: Principles and Best Practice

DTIC Science & Technology

2012-08-01

habitats for specific species of trout . The report noted that these uncertainties — and the SMEs, who had past experience in such topic areas — were...reduce uncertainty in HREP projects is reflected in the completion of the Pool 11 Islands (UMRS RM 583-593) HREP in 2003. In 1989 the Browns Lake

Development and Evaluation of an Experimental Curriculum for the New Quincy (Mass.) Vocational-Technical School. The Science Curriculum.

ERIC Educational Resources Information Center

Champagne, Audrey; Albert, Anne

Activities concerning the development of the science curriculum of Project ABLE are summarized. The science curriculum attempts to relate science content to vocational areas where applicable, but emphasizes generalizations which the student will apply in his specific vocational field. Intended for 10th, 11th, and 12th grade students, the…

Ride quality systems for commuter aircraft

NASA Technical Reports Server (NTRS)

Downing, D. R.; Hammond, T. A.; Amin, S. P.

1983-01-01

The state-of-the-art in Active Ride Augmentation, specifically in terms of its feasibility for commuter aircraft applications. A literature survey was done, and the principal results are presented here through discussion of different Ride Quality Augmentation System (RQAS) designs and advances in related technologies. Recommended follow-on research areas are discussed, and a preliminary RQAS configuration for detailed design and development is proposed.

Graph Theory and Brain Connectivity in Alzheimer's Disease.

PubMed

delEtoile, Jon; Adeli, Hojjat

2017-04-01

This article presents a review of recent advances in neuroscience research in the specific area of brain connectivity as a potential biomarker of Alzheimer's disease with a focus on the application of graph theory. The review will begin with a brief overview of connectivity and graph theory. Then resent advances in connectivity as a biomarker for Alzheimer's disease will be presented and analyzed.

Universal Design for Learning in the Classroom: Practical Applications. What Works for Special-Needs Learners Series

ERIC Educational Resources Information Center

Hall, Tracey E., Ed.; Meyer, Anne, Ed.; Rose, David H., Ed.

2012-01-01

Clearly written and well organized, this book shows how to apply the principles of universal design for learning (UDL) across all subject areas and grade levels. The editors and contributors describe practical ways to develop classroom goals, assessments, materials, and methods that use UDL to meet the needs of all learners. Specific teaching…

Development and application of a spatial IBM to forecast greater prairie-chicken population responses to land use in the Flint Hills region of Kansas - SCB meeting

EPA Science Inventory

Greater prairie-chicken (Tympanachus cupido) populations have been on the decline for decades. Recent efforts to reverse this trend are focusing on two specific disturbance regimes, cattle grazing and field burning, both prevalent in the Flint Hill region of Kansas -- an area of...

University Research Initiative Research Program Summaries

DTIC Science & Technology

1987-06-01

application to intelligent tutoring systems (John Anderson), o Autonomous learning systems (Jaime Carbonell), o Learning algorithms for parallel processing...test them. The primary project will be: o Learning mechanisms in scientific discovery (Herbert Simon). Tutoring systems. These projects are aimed at...near-term results. They 19 will produce tutors for training specific subject matter areas. These projects will push theories of learning forward by

Vertical Profunda Artery Perforator Flap for Plantar Foot Wound Closure: A New Application.

PubMed

Alfonso, Allyson R; Mayo, James L; Sharma, Vishal K; Allen, Robert J; Chiu, Ernest S

2018-02-01

Plantar foot reconstruction requires special consideration of both form and function. There are several fasciocutaneous flap options, each with indications and reservations. This case presents a new application of the vertical profunda artery perforator flap for definitive closure of a neuropathic foot ulcer in a young woman with spina bifida. The postoperative course was uneventful, and the flap survived completely. The surgical and donor sites were without wound recurrence at 5-month follow-up. Understanding the variability of foot flap options is important because of unique cases such as the one presented where the wound was caused by specific and less commonly observed foot anatomy. The specific choice to use the vertical profunda artery perforator flap for this patient and her neuropathic wound type was made based on its excellent flexibility, durability, and donor site appeal. The vertical profunda artery perforator flap has adequate surface area and bulk and a favorable pedicle length and caliber, can be thinned, and leaves a donor scar in a less conspicuous area than other popular free flaps for lower-extremity reconstruction. For these reasons, it should be considered a first-line therapy for free flap coverage of selected foot wounds.

Focus modulation of cylindrical vector beams by using 1D photonic crystal lens with negative refraction effect.

PubMed

Xu, Ji; Zhong, Yi; Wang, Shengming; Lu, Yunqing; Wan, Hongdan; Jiang, Jian; Wang, Jin

2015-10-19

Sub-wavelength focusing of cylindrical vector beams (CVBs) has attracted great attention due to the specific physical effects and the applications in many areas. More powerful, flexible and effective ways to modulate the focus transversally and also longitudinally are always being pursued. In this paper, cylindrically symmetric lens composed of negative-index one-dimensional photonic crystal is proposed to make a breakthrough. By revealing the relationship between focal length and the exit surface shape of the lens, a quite simple and effective principle of designing the lens structure is presented to realize specific focus modulation. Plano-concave lenses are parameterized to modulate the focal length and the number of focuses. An axicon constructed by one-dimensional photonic crystal is proposed for the first time to obtain a large depth of focus and an optical needle focal field with almost a theoretical minimum FWHM of 0.362λ is achieved under radially polarized incident light. Because of the almost identical negative refractive index for TE and TM polarization states, all the modulation methods can be applied for any arbitrary polarized CVBs. This work offers a promising methodology for designing negative-index lenses in related application areas.

Evaluating radiographers' diagnostic accuracy in screen-reading mammograms: what constitutes a quality study?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Debono, Josephine C, E-mail: josephine.debono@bci.org.au; Poulos, Ann E; Westmead Breast Cancer Institute, Westmead, New South Wales

The aim of this study was to first evaluate the quality of studies investigating the diagnostic accuracy of radiographers as mammogram screen-readers and then to develop an adapted tool for determining the quality of screen-reading studies. A literature search was used to identify relevant studies and a quality evaluation tool constructed by combining the criteria for quality of Whiting, Rutjes, Dinnes et al. and Brealey and Westwood. This constructed tool was then applied to the studies and subsequently adapted specifically for use in evaluating quality in studies investigating diagnostic accuracy of screen-readers. Eleven studies were identified and the constructed toolmore » applied to evaluate quality. This evaluation resulted in the identification of quality issues with the studies such as potential for bias, applicability of results, study conduct, reporting of the study and observer characteristics. An assessment of the applicability and relevance of the tool for this area of research resulted in adaptations to the criteria and the development of a tool specifically for evaluating diagnostic accuracy in screen-reading. This tool, with further refinement and rigorous validation can make a significant contribution to promoting well-designed studies in this important area of research and practice.« less

Fabrication of three dimensional patterns of wide dimensional range using microbes and their applications

PubMed Central

Mehta, Sunita; Murugeson, Saravanan; Prakash, Balaji; Deepak

2015-01-01

Inspired by the wound healing property of certain trees, we report a novel microbes based additive process for producing three dimensional patterns, which has a potential of engineering applications in a variety of fields. Imposing a two dimensional pattern of microbes on a gel media and allowing them to grow in the third dimension is known from its use in biological studies. Instead, we have introduced an intermediate porous substrate between the gel media and the microbial growth, which enables three dimensional patterns in specific forms that can be lifted off and used in engineering applications. In order to demonstrate the applicability of this idea in a diverse set of areas, two applications are selected. In one, using this method of microbial growth, we have fabricated microlenses for enhanced light extraction in organic light emitting diodes, where densely packed microlenses of the diameters of hundreds of microns lead to luminance increase by a factor of 1.24X. In another entirely different type of application, braille text patterns are prepared on a normal office paper where the grown microbial colonies serve as braille tactile dots. Braille dot patterns thus prepared meet the standard specifications (size and spacing) for braille books. PMID:26486847

Enhancing Adsorption Capacity while Maintaining Specific Recognition Performance of Mesoporous Silica: A Novel Imprinting Strategy with Amphiphilic Ionic Liquid as Surfactant.

PubMed

Ding, Shichao; Li, Zhiling; Cheng, Yuan; Du, Chunbao; Gao, Junfeng; Zhang, Yong-Wei; Zhang, Nan; Li, Zhaotong; Chang, Ninghui; Hu, Xiaoling

2018-06-21

In order to facilitate the broad applications of molecular recognition materials in biomedical areas, it is critical to enhance their adsorption capacity while maintaining their excellent recognition performance. In this work, we designed and synthesized well-defined peptide-imprinted mesoporous silica (PIMS) for specific recognition of an immunostimulating hexapeptide from human casein (IHHC) by using amphiphilic ionic liquid as the surfactant to anchor IHHC via a combination of one step sol-gel method and docking oriented imprinting approach. Thereinto, theoretical calculation was employed to reveal the multiple binding interactions and dual-template configuration between amphiphilic ionic liquid and IHHC. The fabricated PIMS was characterized and an in-depth analysis of specific recognition mechanism was conducted. Results revealed that both adsorption and recognition capabilities of PIMS far exceeded that of the NIMS's. More significantly, the PIMS exhibited a superior binding capacity (60.5 mg g-1), which could increase 18.9% than the previous work. The corresponding imprinting factor and selectivity coefficient could reach up to 4.51 and 3.30, respectively. The PIMS also possessed lickety-split kinetic binding for IHHC, which the equilibrium time was only 10 min. All of these merits were due to the high surface area and the synergistic effect of multiple interactions (including hydrogen bonding, π-π stacking, ion-ion electrostatic interactions and van der Waals interactions, etc.) between PIMS and IHHC in imprinted sites. The present work suggests the potential application of PIMS for large-scale and high-effective separation of IHHC, which may lead to their broad applications in drug/gene deliver, biosensors, catalyst and so on. © 2018 IOP Publishing Ltd.

Ultrathin and lightweight organic solar cells with high flexibility

PubMed Central

Kaltenbrunner, Martin; White, Matthew S.; Głowacki, Eric D.; Sekitani, Tsuyoshi; Someya, Takao; Sariciftci, Niyazi Serdar; Bauer, Siegfried

2012-01-01

Application-specific requirements for future lighting, displays and photovoltaics will include large-area, low-weight and mechanical resilience for dual-purpose uses such as electronic skin, textiles and surface conforming foils. Here we demonstrate polymer-based photovoltaic devices on plastic foil substrates less than 2 μm thick, with equal power conversion efficiency to their glass-based counterparts. They can reversibly withstand extreme mechanical deformation and have unprecedented solar cell-specific weight. Instead of a single bend, we form a random network of folds within the device area. The processing methods are standard, so the same weight and flexibility should be achievable in light emitting diodes, capacitors and transistors to fully realize ultrathin organic electronics. These ultrathin organic solar cells are over ten times thinner, lighter and more flexible than any other solar cell of any technology to date. PMID:22473014

Molecularly imprinted polymers for the recognition of proteins: the state of the art.

PubMed

Bossi, A; Bonini, F; Turner, A P F; Piletsky, S A

2007-01-15

Molecular imprinting has proved to be an effective technique for the creation of recognition sites on a polymer scaffold. Protein imprinting has been a focus for many chemists working in the area of molecular recognition, since the creation of synthetic polymers that can specifically recognise proteins is a very challenging but potentially extremely rewarding objective. It is expected that molecularly imprinted polymers (MIPs) with specificity for proteins will find application in medicine, diagnostics, proteomics, environmental analysis, sensors and drug delivery. In this review, the authors provide an overview of the progress achieved in the decade between 1994 and 2005, with respect to the challenging area of MIPs for protein recognition. The discussion furnishes a comparative analysis of different approaches developed, underlining their relative advantages and disadvantages and highlighting trends and possible future directions.

Advanced Image Processing for NASA Applications

NASA Technical Reports Server (NTRS)

LeMoign, Jacqueline

2007-01-01

The future of space exploration will involve cooperating fleets of spacecraft or sensor webs geared towards coordinated and optimal observation of Earth Science phenomena. The main advantage of such systems is to utilize multiple viewing angles as well as multiple spatial and spectral resolutions of sensors carried on multiple spacecraft but acting collaboratively as a single system. Within this framework, our research focuses on all areas related to sensing in collaborative environments, which means systems utilizing intracommunicating spatially distributed sensor pods or crafts being deployed to monitor or explore different environments. This talk will describe the general concept of sensing in collaborative environments, will give a brief overview of several technologies developed at NASA Goddard Space Flight Center in this area, and then will concentrate on specific image processing research related to that domain, specifically image registration and image fusion.

NASA Glenn Research Center Electrochemistry Branch Battery Overview

NASA Technical Reports Server (NTRS)

Manzo, Michelle A.

2010-01-01

This presentation covers an overview of NASA Glenn s history and heritage in the development of electrochemical systems for aerospace applications. Specific areas of focus are Li-ion batteries and their development for future Exploration missions. Current component development efforts for high energy and ultra high energy Li-ion batteries are addressed. Electrochemical systems are critical to the success of Exploration, Science and Space Operations missions. NASA Glenn has a long, successful heritage with batteries and fuel cells for aerospace applications. GRC Battery capabilities and expertise span basic research through flight hardware development and implementation. There is a great deal of synergy between energy storage system needs for aerospace and terrestrial applications.

Selected Topics on the Synthesis, Properties and Applications of Multiwalled Carbon Nanotubes

PubMed Central

Stoner, B.R.; Brown, B.; Glass, J.T.

2014-01-01

Summary In summary, MWCNTs have been examined for a variety of electronic applications due to their unique structure and chemistry. Electrodes for field emission, energy and sensor applications hold particular interest. MWCNTs provide a very high surface area, relatively easy methods of surface modification, controllable and high concentration of reactive surface sites, and high specific capacitance. Combining MWCNTs with graphene structures, oxide and metal nanoparticles and certain polymers extends their performance and functionality. Such hybrid structures have been produced in situ during CNT growth and in two-step processes. Excellent progress on understanding the mechanisms of CNT growth has enabled numerous growth methods to all yield MWCNT structures in a variety of morphologies. PMID:24910503