Geologic and hydraulic characteristics of selected shaly geologic units in Oklahoma

USGS Publications Warehouse

Becker, C.J.; Overton, M.D.; Johnson, K.S.; Luza, K.V.

1997-01-01

Information was collected on the geologic and hydraulic characteristics of three shale-dominated units in Oklahoma-the Dog Creek Shale and Chickasha Formation in Canadian County, Hennessey Group in Oklahoma County, and the Boggy Formation in Pittsburg County. The purpose of this project was to gain insight into the characteristics controlling fluid flow in shaly units that could be targeted for confinement of hazardous waste in the State and to evaluate methods of measuring hydraulic characteristics of shales. Permeameter results may not indicate in-place small-scale hydraulic characteristics, due to pretest disturbance and deterioration of core samples. The Dog Creek Shale and Chickasha Formation hydraulic conductivities measured by permeameter methods ranged from 2.8 times 10 to the negative 11 to 3.0 times 10 to the negative 7 meter per second in nine samples and specific storage from 3.3 times 10 to the negative 4 to 1.6 times 10 to the negative 3 per meter in four samples. Hennessey Group hydraulic conductivities ranged from 4.0 times 10 to the negative 12 to 4.0 times 10 to the negative 10 meter per second in eight samples. Hydraulic conductivity in the Boggy Formation ranged from 1.7 times 10 to the negative 12 to 1.0 times 10 to the negative 8 meter per second in 17 samples. The hydraulic properties of isolated borehole intervals of average length of 4.5 meters in the Hennessey Group and the Boggy Formation were evaluated by a pressurized slug-test method. Hydraulic conductivities obtained with this method tend to be low because intervals with features that transmitted large volumes of water were not tested. Hennessey Group hydraulic conductivities measured by this method ranged from 3.0 times 10 to the negative 13 to 1.1 times 10 to the negative 9 meter per second; the specific storage values are small and may be unreliable. Boggy Formation hydraulic conductivities ranged from 2.0 times 10 to the negative 13 to 2.7 times 10 to the negative 10 meter per second and specific storage values in these tests also are small and may be unreliable. A substantially higher hydraulic conductivity of 3.0 times 10 to the negative 8 meter per second was measured in one borehole 30 meters deep in the Boggy Formation using an open hole slug-test method.

Bromide, Chloride, and Sulfate Concentrations, and Specific Conductance, Lake Texoma, Texas and Oklahoma, 2007-08

USGS Publications Warehouse

Baldys, Stanley

2009-01-01

The U.S. Geological Survey, in cooperation with the City of Dallas Water Utilities Division, collected water-quality data from 11 sites on Lake Texoma, a reservoir on the Texas-Oklahoma border, during April 2007-September 2008. At 10 of the sites, physical properties (depth, specific conductance, pH, temperature, dissolved oxygen, and alkalinity) were measured and samples were collected for analysis of selected dissolved constituents (bromide, calcium, magnesium, potassium, sodium, carbonate, bicarbonate, chloride, and sulfate); at one site, only physical properties were measured. The primary constituent of interest was bromide. Bromate can form when ozone is used to disinfect raw water containing bromide, and bromate is a suspected human carcinogen. Chloride and sulfate were of secondary interest. Only the analytical results for bromide, chloride, sulfate, and measured specific conductance are discussed in this report. Median dissolved bromide concentrations ranged from 0.28 to 0.60 milligrams per liter. The largest median dissolved bromide concentration (0.60 milligram per liter at site 11) was from the Red River arm of Lake Texoma. Dissolved bromide concentrations generally were larger in the Red River arm of Lake Texoma than in the Washita arm of the lake. Median dissolved chloride concentrations were largest in the Red River arm of Lake Texoma at site 11 (431 milligrams per liter) and smallest at site 8 (122 milligrams per liter) in the Washita arm. At site 11 in the Red River arm, the mean and median chloride concentrations exceeded the secondary maximum contaminant level of 300 milligrams per liter for chloride established by the 'Texas Surface Water Quality Standards' for surface-water bodies designated for the public water supply use. Median dissolved sulfate concentrations ranged from 182 milligrams per liter at site 4 in the Big Mineral arm to 246 milligrams per liter at site 11 in the Red River arm. None of the mean or median sulfate concentrations exceeded the secondary maximum contaminant level of 300 milligrams per liter. Median specific conductance measurements at sites ranged from 1,120 microsiemens per centimeter at site 8 in the Washita arm to 2,100 microsiemens per centimeter in the Red River arm. The spatial distribution of specific conductance in Lake Texoma was similar to that of bromide and chloride, with larger specific conductance values in the Red River arm compared to those in the Washita arm.

Specific Conductance and Dissolved-Solids Characteristics for the Green River and Muddy Creek, Wyoming, Water Years 1999-2008

USGS Publications Warehouse

Clark, Melanie L.; Davidson, Seth L.

2009-01-01

Southwestern Wyoming is an area of diverse scenery, wildlife, and natural resources that is actively undergoing energy development. The U.S. Department of the Interior's Wyoming Landscape Conservation Initiative is a long-term science-based effort to assess and enhance aquatic and terrestrial habitats at a landscape scale, while facilitating responsible energy development through local collaboration and partnerships. Water-quality monitoring has been conducted by the U.S. Geological Survey on the Green River near Green River, Wyoming, and Muddy Creek near Baggs, Wyoming. This monitoring, which is being conducted in cooperation with State and other Federal agencies and as part of the Wyoming Landscape Conservation Initiative, is in response to concerns about potentially increased dissolved solids in the Colorado River Basin as a result of energy development. Because of the need to provide real-time dissolved-solids concentrations for the Green River and Muddy Creek on the World Wide Web, the U.S. Geological Survey developed regression equations to estimate dissolved-solids concentrations on the basis of continuous specific conductance using relations between measured specific conductance and dissolved-solids concentrations. Specific conductance and dissolved-solids concentrations were less varied and generally lower for the Green River than for Muddy Creek. The median dissolved-solids concentration for the site on the Green River was 318 milligrams per liter, and the median concentration for the site on Muddy Creek was 943 milligrams per liter. Dissolved-solids concentrations ranged from 187 to 594 milligrams per liter in samples collected from the Green River during water years 1999-2008. Dissolved-solids concentrations ranged from 293 to 2,485 milligrams per liter in samples collected from Muddy Creek during water years 2006-08. The differences in dissolved-solids concentrations in samples collected from the Green River compared to samples collected from Muddy Creek reflect the different basin characteristics. Relations between specific conductance and dissolved-solids concentrations were statistically significant for the Green River (p-value less than 0.001) and Muddy Creek (p-value less than 0.001); therefore, specific conductance can be used to estimate dissolved-solids concentrations. Using continuous specific conductance values to estimate dissolved solids in real-time on the World Wide Web increases the amount and improves the timeliness of data available to water managers for assessing dissolved-solids concentrations in the Colorado River Basin.

Thermal conductivity measurements of epoxy systems at low temperature

NASA Astrophysics Data System (ADS)

Rondeaux, F.; Bredy, Ph.; Rey, J. M.

2002-05-01

We have developed a specific thermal conductivity measurement facility for solid materials at low temperature (LHe and LN2). At present, the Measurement of Thermal Conductivity of Insulators (MECTI) facility performs measurements on epoxy resin, as well as on bulk materials such as aluminum alloy and on insulators developed at Saclay. Thermal conductivity measurements on pre-impregnated fiber-glass epoxy composite are presented in the temperature range of 4.2 K to 14 K for different thicknesses in order to extract the thermal boundary resistance. We also present results obtained on four different bonding glues (Stycast 2850 FT, Poxycomet F, DP190, Eccobond 285) in the temperature range of 4.2 K to 10 K.

[Recording and data processing of electrical signals of the specific atrioventricular conduction pathways in man].

PubMed

Héron, F; Mialet, G; Schuller, C; Breton, D; Perrin, J; Degeorges, M

1979-01-01

Signals of the electrical activity of the specific atrioventricular conduction pathways were recorded with an unipolar lead to obtain an exact time reference. The amplifier used had special characteristics: high gain settings (up to 300,000), very low noise levels, and wide filter range (2 Hz - 1,600 Hz). The low amplitude of the signals under study, of the order of a microvolt, and the wide filter range of the amplifier necessitated placing the patient in a Faraday cage. The signals recorded on magnetic tape were treated by a system of analysis for signal treatment. The method of averaging was used to extract the signal from background noise especially that arising from somatic muscle. The amplitude of the Hisian signal was much larger than that usually obtained with other methods. The intervals were determined with precision of the order of 1 millisecond. Frequential analysis of the signals gave another representation of the information contained in the time signals. This new representation seems to give better discrimination of the different zones of activation of the specific atrioventricular conduction pathways.

Water quality in Gaines Creek and Gaines Creek arm of Eufaula Lake, Oklahoma

USGS Publications Warehouse

Kurklin, J.K.

1990-01-01

Based on samples collected from May 1978 to May 1980 and analyzed for major anions, nitrogen, trace elements, phytoplankton, and bacteria, the water in Gaines Creek and the Gaines Creek arm of Eufaula Lake was similar with respect to suitability for municipal use. Water from Gaines Creek had a pH range of 5.7 to 7.6 and a maximum specific conductance of 97 microsiemens per centimeter at 25o Celsius, whereas water from the Gaines Creek arm of Eufaula Lake had a pH range of 6.0 to 9.2 and a maximum specific conductance of 260 microsiemens per centimeter at 25o Celsius. Dissolved oxygen, pH, temperature, and specific conductance values for the lake varied with depth. With the exceptions of cadmium, iron, lead, and manganese, trace-element determinations of samples were within recommended national primary and secondary drinking-water standards. When compared to the National Academy of Sciences water-quality criteria, phytoplankton and bacteria counts exceeded recommendations; however, water from either Gaines Creek or Eufaula Lake could be treated similarly and used as a municipal water supply.

Aquifer characteristics, water availability, and water quality of the Quaternary aquifer, Osage County, northeastern Oklahoma, 2001-2002

USGS Publications Warehouse

Mashburn, Shana L.; Cope, Caleb C.; Abbott, Marvin M.

2003-01-01

Additional sources of water are needed on the Osage Reservation for future growth and development. The Quaternary aquifer along the Arkansas River in the Osage Reservation may represent a substantial water resource, but limited amounts of hydrogeologic data were available for the aquifer. The study area is about 116 square miles of the Quaternary aquifer in the Arkansas River valley and the nearby upland areas along the Osage Reservation. The study area included the Arkansas River reach downstream from Kaw Lake near Ponca City, Oklahoma to upstream from Keystone Lake near Cleveland, Oklahoma. Electrical conductivity logs were produced for 103 test holes. Water levels were determined for 49 test holes, and 105 water samples were collected for water-quality field analyses at 46 test holes. Water-quality data included field measurements of specific conductance, pH, water temperature, dissolved oxygen, and nitrate (nitrite plus nitrate as nitrogen). Sediment cores were extracted from 20 of the 103 test holes. The Quaternary aquifer consists of alluvial and terrace deposits of sand, silt, clay, and gravel. The measured thickness of the alluvium ranged from 13.7 to 49.8 feet. The measured thickness of the terrace sediments ranged from 7 to 93.8 feet. The saturated thickness of all sediments ranged from 0 to 38.2 feet with a median of 24.8 feet. The weighted-mean grain size for cores from the alluvium ranged from 3.69 to 0.64 f, (0.08- 0.64 millimeter), and ranged from 4.02 to 2.01 f (0.06-0.25 millimeter) for the cores from terrace deposits. The mean of the weighted-mean grain sizes for cores from the alluvium was 1.67 f (0.31 millimeter), and the terrace deposits was 2.73 f (0.15 millimeter). The hydraulic conductivity calculated from grain size of the alluvium ranged from 2.9 to 6,000 feet per day and of the terrace deposits ranged from 2.9 to 430 feet per day. The calculated transmissivity of the alluvium ranged from 2,000 to 26,000 feet squared per day with a median of 5,100 feet squared per day. Water in storage in the alluvium was estimated to be approximately 200,000 acre-feet. The amount of water annually recharging the aquifer was estimated to be approximately 4,800 acre-feet. Specific conductance for all water samples ranged from 161 to 6,650 microsiemens per centimeter. Median specific conductance for the alluvium was 683 microsiemens per centimeter and for the terrace deposits was 263 microsiemens per centimeter. Dissolved-solids concentrations, estimated from specific conductance, for water samples from the aquifer ranged from 88 to 3,658 milligrams per liter. Estimated median dissolved- solids concentration for the alluvium was 376 milligrams per liter and for the terrace deposits was 145 milligrams per liter. More than half of the samples from the Quaternary aquifer were estimated to contain less than 500 milligrams per liter dissolved solids. Field-screened nitrate concentrations for the sampling in December 2001-August 2002 ranged from 0 to 15 milligrams per liter. The field-screened nitrate concentrations for the second sampling in September 2002 were less than corresponding laboratory reported values.

Chapter 17. Guidelines for restoration and rehabilitation of principal plant communities

Treesearch

Richard Stevens; Stephen B. Monsen

2004-01-01

Range and wildland improvement projects conducted throughout the Intermountain region normally occur within specific plant communities. Each plant community has unique features that require different equipment, planting techniques, and plant materials to conduct improvement projects. Plant communities or associations discussed in this chapter are: (1) subalpine...

Fulfillment of Koch’s postulates and partial host range of Septoria lepidii Desm., a fungal pathogen for potential biological control of hoary cress (Lepidium spp.)

USDA-ARS?s Scientific Manuscript database

We have fulfilled Koch’s postulates and conducted host range tests with Septoria lepidii Desm. on five geographical accessions of hoary cress. Host range results showed the fungus specific to Lepidium spp. and damaging to hoary cress. This fungus is potentially an important biological control agent ...

Automatic EMC test system

NASA Astrophysics Data System (ADS)

Kasai, R.; Abe, T.; Sano, T.

Automated electromagnetic compatibility (EMC) tests for spacecraft hardware are described. EMC tests are divided into three categories: compensating measurement and calibration errors, comparison of test results with specification, and fine-frequency searching using predictive interference analysis. The automated system features an RF receiver and transmitter, a control system, and antennas. Trials are run with conducted and radiated emissions and conducted and radiated susceptibility over a frequency range of 0.1-40 GHz with narrow, broad and random broad band noise. The system meets military specifications 1541, 461, and 462.

Effect of Temperature and Nutrient Manipulations on eelgrass ...

EPA Pesticide Factsheets

Global climate change will have a large impact on the three predominate drivers of estuarine seagrass productivity, temperature, light and nutrients. I experimentally evaluate the response of Pacific Northwest Z. marina to interactive effects of temperature and nutrient conditions. Experimental manipulations were conducted hydroponically in acrylic chambers and spanned a range of temperatures and nutrient concentrations. Preliminary single factor experiments were conducted to evaluate physiological tolerances to temperature and nitrogen concentrations. Eelgrass exhibited a linear increase in specific growth with increasing NH4 concentration (range from 10 to 1000 µM); in contrast, there was no significant relationship between specific growth rate and increasing NO3 concentration over the same concentration range. Leaf growth metrics all exhibited strong linear relationships with increasing water temperature (temperature range 4-25 ºC). In the factorial experiment, plants were exposed to 3 temperatures (10, 18 and 25 ºC) and 3 nitrate concentrations (10, 30 and 100 µM) with 3 replicate chambers per treatment combination. Most metrics (leaf elongation, growth, specific growth, wasting index) exhibited a significant temperature effect indicating the importance of temperature on metabolic rates. Tissue stable isotope ratios and C:N values exhibited a significant nutrient effect and in some cases a significant temperature effect. Whole plant non structur

Graphite fiber/copper matrix composites for space power heat pipe fin applications

NASA Astrophysics Data System (ADS)

McDanels, David L.; Baker, Karl W.; Ellis, David L.

1991-01-01

High specific thermal conductivity (thermal conductivity divided by density) is a major design criterion for minimizing system mass for space power systems. For nuclear source power systems, graphite fiber reinforced copper matrix (Gr/Cu) composites offer good potential as a radiator fin material operating at service temperatures above 500 K. Specific thermal conductivity in the longitudinal direction is better than beryllium and almost twice that of copper. The high specific thermal conductivity of Gr/Cu offers the potential of reducing radiator mass by as much as 30 percent. Gr/Cu composites also offer the designer a range of available properties for various missions and applications. The properties of Gr/Cu are highly anisotropic. Longitudinal elastic modulus is comparable to beryllium and about three times that of copper. Thermal expansion in the longitudinal direction is near zero, while it exceeds that of copper in the transverse direction.

High frequency, high temperature specific core loss and dynamic B-H hysteresis loop characteristics of soft magnetic alloys

NASA Technical Reports Server (NTRS)

Wieserman, W. R.; Schwarze, G. E.; Niedra, J. M.

1990-01-01

Limited experimental data exists for the specific core loss and dynamic B-H loops for soft magnetic materials for the combined conditions of high frequency and high temperature. This experimental study investigates the specific core loss and dynamic B-H loop characteristics of Supermalloy and Metglas 2605SC over the frequency range of 1 to 50 kHz and temperature range of 23 to 300 C under sinusoidal voltage excitation. The experimental setup used to conduct the investigation is described. The effects of the maximum magnetic flux density, frequency, and temperature on the specific core loss and on the size and shape of the B-H loops are examined.

Role of specific IgE and skin-prick testing in predicting food challenge results to baked egg.

PubMed

Cortot, Catherine F; Sheehan, William J; Permaul, Perdita; Friedlander, James L; Baxi, Sachin N; Gaffin, Jonathan M; Dioun, Anahita F; Hoffman, Elaine B; Schneider, Lynda C; Phipatanakul, Wanda

2012-01-01

Previous studies suggest that children with egg allergy may be able to tolerate baked egg. Reliable predictors of a successful baked egg challenge are not well established. We examined egg white-specific IgE levels, skin-prick test (SPT) results, and age as predictors of baked egg oral food challenge (OFC) outcomes. We conducted a retrospective chart review of children, aged 2-18 years, receiving an egg white-specific IgE level, SPT, and OFC to baked egg from 2008 to 2010. Fifty-two oral baked egg challenges were conducted. Of the 52 challenges, 83% (n = 43) passed and 17% (n = 9) failed, including 2 having anaphylaxis. Median SPT wheal size was 12 mm (range, 0-35 mm) for passed challenges and 17 mm (range, 10-30 mm) for failed challenges (p = 0.091). The negative predictive value for passing the OFC was 100% (9 of 9) if SPT wheal size was <10 mm. Median egg white-specific IgE was 2.02 kU/L (range, <0.35-13.00 kU/L) for passed challenges and 1.52 kU/L (range, 0.51-6.10 kU/L) for failed challenges (p = 0.660). Receiver operating characteristic (ROC) curve analysis for SPT revealed an area under the curve (AUC) of 0.64. ROC curve analysis for egg white-specific IgE revealed an AUC of 0.63. There was no significant difference in age between patients who failed and those who passed (median = 8.8 years versus 7.0 years; p = 0.721). Based on our sample, SPT, egg white-specific IgE and age are not good predictors of passing a baked egg challenge. However, there was a trend for more predictability with SPT wheal size.

Prediction of the Thermal Conductivity of Refrigerants by Computational Methods and Artificial Neural Network.

PubMed

Ghaderi, Forouzan; Ghaderi, Amir H; Ghaderi, Noushin; Najafi, Bijan

2017-01-01

Background: The thermal conductivity of fluids can be calculated by several computational methods. However, these methods are reliable only at the confined levels of density, and there is no specific computational method for calculating thermal conductivity in the wide ranges of density. Methods: In this paper, two methods, an Artificial Neural Network (ANN) approach and a computational method established upon the Rainwater-Friend theory, were used to predict the value of thermal conductivity in all ranges of density. The thermal conductivity of six refrigerants, R12, R14, R32, R115, R143, and R152 was predicted by these methods and the effectiveness of models was specified and compared. Results: The results show that the computational method is a usable method for predicting thermal conductivity at low levels of density. However, the efficiency of this model is considerably reduced in the mid-range of density. It means that this model cannot be used at density levels which are higher than 6. On the other hand, the ANN approach is a reliable method for thermal conductivity prediction in all ranges of density. The best accuracy of ANN is achieved when the number of units is increased in the hidden layer. Conclusion: The results of the computational method indicate that the regular dependence between thermal conductivity and density at higher densities is eliminated. It can develop a nonlinear problem. Therefore, analytical approaches are not able to predict thermal conductivity in wide ranges of density. Instead, a nonlinear approach such as, ANN is a valuable method for this purpose.

Prediction of the Thermal Conductivity of Refrigerants by Computational Methods and Artificial Neural Network

PubMed Central

Ghaderi, Forouzan; Ghaderi, Amir H.; Ghaderi, Noushin; Najafi, Bijan

2017-01-01

Background: The thermal conductivity of fluids can be calculated by several computational methods. However, these methods are reliable only at the confined levels of density, and there is no specific computational method for calculating thermal conductivity in the wide ranges of density. Methods: In this paper, two methods, an Artificial Neural Network (ANN) approach and a computational method established upon the Rainwater-Friend theory, were used to predict the value of thermal conductivity in all ranges of density. The thermal conductivity of six refrigerants, R12, R14, R32, R115, R143, and R152 was predicted by these methods and the effectiveness of models was specified and compared. Results: The results show that the computational method is a usable method for predicting thermal conductivity at low levels of density. However, the efficiency of this model is considerably reduced in the mid-range of density. It means that this model cannot be used at density levels which are higher than 6. On the other hand, the ANN approach is a reliable method for thermal conductivity prediction in all ranges of density. The best accuracy of ANN is achieved when the number of units is increased in the hidden layer. Conclusion: The results of the computational method indicate that the regular dependence between thermal conductivity and density at higher densities is eliminated. It can develop a nonlinear problem. Therefore, analytical approaches are not able to predict thermal conductivity in wide ranges of density. Instead, a nonlinear approach such as, ANN is a valuable method for this purpose. PMID:29188217

2010 NASA Range Safety Annual Report

NASA Technical Reports Server (NTRS)

Dumont, Alan G.

2010-01-01

this report provides a NASA Range Safety overview for current and potential range users. This report contains articles which cover a variety of subject areas, summaries of various NASA Range Safety Program activities conducted during the past year, links to past reports, and information on several projects that may have a profound impact on the way business will be done in the future. Specific topics discussed in the 2010 NASA Range Safety Annual Report include a program overview and 2010 highlights; Range Safety Training; Range Safety Policy revision; Independent Assessments; Support to Program Operations at all ranges conducting NASA launch/flight operations; a continuing overview of emerging range safety-related technologies; and status reports from all of the NASA Centers that have Range Safety responsibilities. Every effort has been made to include the most current information available. We recommend this report be used only for guidance and that the validity and accuracy of all articles be verified for updates. Once again, the web-based format was used to present the annual report.

Estimating Concentrations of Road-Salt Constituents in Highway-Runoff from Measurements of Specific Conductance

USGS Publications Warehouse

Granato, Gregory E.; Smith, Kirk P.

1999-01-01

Discrete or composite samples of highway runoff may not adequately represent in-storm water-quality fluctuations because continuous records of water stage, specific conductance, pH, and temperature of the runoff indicate that these properties fluctuate substantially during a storm. Continuous records of water-quality properties can be used to maximize the information obtained about the stormwater runoff system being studied and can provide the context needed to interpret analyses of water samples. Concentrations of the road-salt constituents calcium, sodium, and chloride in highway runoff were estimated from theoretical and empirical relations between specific conductance and the concentrations of these ions. These relations were examined using the analysis of 233 highwayrunoff samples collected from August 1988 through March 1995 at four highway-drainage monitoring stations along State Route 25 in southeastern Massachusetts. Theoretically, the specific conductance of a water sample is the sum of the individual conductances attributed to each ionic species in solution-the product of the concentrations of each ion in milliequivalents per liter (meq/L) multiplied by the equivalent ionic conductance at infinite dilution-thereby establishing the principle of superposition. Superposition provides an estimate of actual specific conductance that is within measurement error throughout the conductance range of many natural waters, with errors of less than ?5 percent below 1,000 microsiemens per centimeter (?S/cm) and ?10 percent between 1,000 and 4,000 ?S/cm if all major ionic constituents are accounted for. A semi-empirical method (adjusted superposition) was used to adjust for concentration effects-superposition-method prediction errors at high and low concentrations-and to relate measured specific conductance to that calculated using superposition. The adjusted superposition method, which was developed to interpret the State Route 25 highway-runoff records, accounts for contributions of constituents other than calcium, sodium, and chloride in dilute waters. The adjusted superposition method also accounts for the attenuation of each constituent's contribution to conductance as ionic strength increases. Use of the adjusted superposition method generally reduced predictive error to within measurement error throughout the range of specific conductance (from 37 to 51,500 ?S/cm) in the highway runoff samples. The effects of pH, temperature, and organic constituents on the relation between concentrations of dissolved constituents and measured specific conductance were examined but these properties did not substantially affect interpretation of the Route 25 data set. Predictive abilities of the adjusted superposition method were similar to results obtained by standard regression techniques, but the adjusted superposition method has several advantages. Adjusted superposition can be applied using available published data about the constituents in precipitation, highway runoff, and the deicing chemicals applied to a highway. This semi-empirical method can be used as a predictive and diagnostic tool before a substantial number of samples are collected, but the power of the regression method is based upon a large number of water-quality analyses that may be affected by a bias in the data.

Configuration management issues and objectives for a real-time research flight test support facility

NASA Technical Reports Server (NTRS)

Yergensen, Stephen; Rhea, Donald C.

1988-01-01

An account is given of configuration management activities for the Western Aeronautical Test Range (WATR) at NASA-Ames, whose primary function is the conduct of aeronautical research flight testing through real-time processing and display, tracking, and communications systems. The processing of WATR configuration change requests for specific research flight test projects must be conducted in such a way as to refrain from compromising the reliability of WATR support to all project users. Configuration management's scope ranges from mission planning to operations monitoring and performance trend analysis.

Calculation of thermal conductivity, thermal diffusivity and specific heat capacity of sedimentary rocks using petrophysical well logs

NASA Astrophysics Data System (ADS)

Fuchs, Sven; Balling, Niels; Förster, Andrea

2015-12-01

In this study, equations are developed that predict for synthetic sedimentary rocks (clastics, carbonates and evapourates) thermal properties comprising thermal conductivity, specific heat capacity and thermal diffusivity. The rock groups are composed of mineral assemblages with variable contents of 15 major rock-forming minerals and porosities of 0-30 per cent. Petrophysical properties and their well-logging-tool-characteristic readings were assigned to these rock-forming minerals and to pore-filling fluids. Relationships are explored between each thermal property and other petrophysical properties (density, sonic interval transit time, hydrogen index, volume fraction of shale and photoelectric absorption index) using multivariate statistics. The application of these relations allows computing continuous borehole profiles for each rock thermal property. The uncertainties in the prediction of each property vary depending on the selected well-log combination. Best prediction is in the range of 2-8 per cent for the specific heat capacity, of 5-10 per cent for the thermal conductivity, and of 8-15 for the thermal diffusivity, respectively. Well-log derived thermal conductivity is validated by laboratory data measured on cores from deep boreholes of the Danish Basin, the North German Basin, and the Molasse Basin. Additional validation of thermal conductivity was performed by comparing predicted and measured temperature logs. The maximum deviation between these logs is <3 °C. The thermal-conductivity calculation allowed an evaluation of the depth range in which the palaeoclimatic effect on the subsurface temperature field can be observed in the North German Basin. This effect reduces the surface heat-flow density by 25 mW m-2.

Strong, light, multifunctional fibers of carbon nanotubes with ultrahigh conductivity.

PubMed

Behabtu, Natnael; Young, Colin C; Tsentalovich, Dmitri E; Kleinerman, Olga; Wang, Xuan; Ma, Anson W K; Bengio, E Amram; ter Waarbeek, Ron F; de Jong, Jorrit J; Hoogerwerf, Ron E; Fairchild, Steven B; Ferguson, John B; Maruyama, Benji; Kono, Junichiro; Talmon, Yeshayahu; Cohen, Yachin; Otto, Marcin J; Pasquali, Matteo

2013-01-11

Broader applications of carbon nanotubes to real-world problems have largely gone unfulfilled because of difficult material synthesis and laborious processing. We report high-performance multifunctional carbon nanotube (CNT) fibers that combine the specific strength, stiffness, and thermal conductivity of carbon fibers with the specific electrical conductivity of metals. These fibers consist of bulk-grown CNTs and are produced by high-throughput wet spinning, the same process used to produce high-performance industrial fibers. These scalable CNT fibers are positioned for high-value applications, such as aerospace electronics and field emission, and can evolve into engineered materials with broad long-term impact, from consumer electronics to long-range power transmission.

Investigation of the technology of conductive yarns manufacturing

NASA Astrophysics Data System (ADS)

Ryklin, Dzmitry; Medvetski, Sergey

2017-10-01

The paper is devoted to development of technology of electrically conductive yarn production. This technology allows manufacturing conductive yarns of copper wire and polyester filament yarns. Method of the predicting of the conductive yarn breaking force was developed on the base of analysing of load-elongation curves of each strand of the yarn. Also the method of the predicting of the conductive yarn diameter was offered. Investigation shows that conductive yarns can be integrated into the textiles structure using sewing or embroidery equipment. Application of developed conductive yarn is wearable electronics creating with wide range of functions, for example, for specific health issue monitoring, navigation tools or communication gadgets.

Results of borehole geophysical logging and hydraulic tests conducted in Area D supply wells, former U.S. Naval Air Warfare Center, Warminster, Pennsylvania

USGS Publications Warehouse

Sloto, Ronald A.; Grazul, Kevin E.

1998-01-01

Borehole geophysical logging, aquifer tests, and aquifer-isolation (packer) tests were conducted in four supply wells at the former U.S. Naval Air Warfare Center (NAWC) in Warminster, PA, to identify the depth and yield of water-bearing zones, occurrence of borehole flow, and effect of pumping on nearby wells. The study was conducted as part of an ongoing evaluation of ground-water contamination at the NAWC. Caliper, natural-gamma, single-point resistance, fluid resistivity, and fluid temperature logs and borehole television surveys were run in the supply wells, which range in depth from 242 to 560 ft (feet). Acoustic borehole televiewer and borehole deviation logs were run in two of the wells. The direction and rate of borehole-fluid movement under non-pumping conditions were measured with a high-resolution heatpulse flowmeter. The logs were used to locate water-bearing fractures, determine probable zones of vertical borehole-fluid movement, and determine the depth to set packers. An aquifer test was conducted in each well to determine open-hole specific capacity and the effect of pumping the open borehole on water levels in nearby wells. Specific capacities ranged from 0.21 to 1.7 (gal/min)/ft (gallons per minute per foot) of drawdown. Aquifer-isolation tests were conducted in each well to determine depth-discrete specific capacities and to determine the effect of pumping an individual fracture or fracture zone on water levels in nearby wells. Specific capacities of individual fractures and fracture zones ranged from 0 to 2.3 (gal/min)/ft. Most fractures identified as water-producing or water-receiving zones by borehole geophysical methods produced water when isolated and pumped. All hydrologically active fractures below 250 ft below land surface were identified as water-receiving zones and produced little water when isolated and pumped. In the two wells greater then 540 ft deep, downward borehole flow to the deep water-receiving fractures is caused by a large difference in head (as much as greater then 49 ft) between water-bearing fractured in the upper and lower part of the borehole. Vertical distribution of specific capacity between land surface and 250 ft below land surface is not related to depth.

Exploring the Use of Suspension in High School Codes of Conduct for Mild, Moderate, and Severe Behaviors

ERIC Educational Resources Information Center

Horwitz, Amy Beth

2010-01-01

The purpose of this investigation is to describe the outcomes of a multi-state study of written discipline policies in a high school setting. This study examines discipline codes of conduct and analyzes the content for behaviors ranging in severity (mild, moderate, and severe) while specifically examining the use of suspension as a punitive…

Passive Biobarrier for Treating Co-mingled Perchlorate and RDX in Groundwater at an Active Range

DTIC Science & Technology

2016-05-12

and Groundwater Temperature ............................. 102 6.1.2 Dissolved Oxygen (DO) and Oxidation Reduction Potential (ORP...22 or equivalent). Parameters, including temperature , conductivity, dissolved oxygen , oxidation-reduction potential (ORP), turbidity, and pH were...3% for temperature and specific conductivity, and ᝺% for dissolved oxygen , ORP, and turbidity. When parameters were stable according to the above

Analysis of three tests of the unconfined aquifer in southern Nassau County, Long Island, New York

USGS Publications Warehouse

Lindner, J.B.; Reilly, T.E.

1982-01-01

Drawdown and recovery data from three 2-day aquifer tests (OF) the unconfined (water-table) aquifer in southern Nassau County, N.Y., during the fall of 1979, were analyzed. Several simple analytical solutions, a typecurve-matching procedure, and a Galerkin finite-element radial-flow model were used to determine hydraulic conductivity, ratio of horizontal to vertical hydraulic conductivity, and specific yield. Results of the curve-matching procedure covered a broad range of values that could be narrowed through consideration of data from other sources such as published reports, drillers ' logs, or values determined by analytical solutions. Analysis by the radial-flow model was preferred because it allows for vertical variability in aquifer properties and solves the system for all observation points simultaneously, whereas the other techniques treat the aquifer as homogeneous and must treat each observation well separately. All methods produced fairly consistent results. The ranges of aquifer values at the three sites were: horizontal hydraulic conductivity, 140 to 380 feet per day; transmissivity 11,200 to 17,100 feet squared per day; ratio of horizontal to vertical hydraulic conductivity 2.4:1 to 7:1, and specific yield , 0.13 to 0.23. (USGS)

Evaluation of Measurements Collected with Multi-Parameter Continuous Water-Quality Monitors in Selected Illinois Streams, 2001-03

USGS Publications Warehouse

Groschen, George E.; King, Robin B.

2005-01-01

Eight streams, representing a wide range of environmental and water-quality conditions across Illinois, were monitored from July 2001 to October 2003 for five water-quality parameters as part of a pilot study by the U.S. Geological Survey (USGS) in cooperation with the Illinois Environmental Protection Agency (IEPA). Continuous recording multi-parameter water-quality monitors were installed to collect data on water temperature, dissolved-oxygen concentrations, specific conductivity, pH, and turbidity. The monitors were near USGS streamflow-gaging stations where stage and streamflow are continuously recorded. During the study period, the data collected for these five parameters generally met the data-quality objectives established by the USGS and IEPA at all eight stations. A similar pilot study during this period for measurement of chlorophyll concentrations failed to achieve the data-quality objectives. Of all the sensors used, the temperature sensors provided the most accurate and reliable measurements (generally within ?5 percent of a calibrated thermometer reading). Signal adjustments and calibration of all other sensors are dependent upon an accurate and precise temperature measurement. The dissolved-oxygen sensors were the next most reliable during the study and were responsive to changing conditions and accurate at all eight stations. Specific conductivity was the third most accurate and reliable measurement collected from the multi-parameter monitors. Specific conductivity at the eight stations varied widely-from less than 40 microsiemens (?S) at Rayse Creek near Waltonville to greater than 3,500 ?S at Salt Creek at Western Springs. In individual streams, specific conductivity often changed quickly (greater than 25 percent in less than 3 hours) and the sensors generally provided good to excellent record of these variations at all stations. The widest range of specific-conductivity measurements was in Salt Creek at Western Springs in the Greater Chicago metropolitan area. Unlike temperature, dissolved oxygen, and specific conductivity that have been typically measured over a wide range of historical streamflow conditions in many streams, there are few historical turbidity data and the full range of turbidity values is not well known for many streams. Because proposed regional criteria for turbidity in regional streams are based on upper 25th percentiles of concentration in reference streams, accurate determination of the distribution of turbidity in monitored streams is important. Digital data from all five sensors were recorded within each of the eight sondes deployed in the streams and in automated data recorders in the nearby streamflow-gaging houses at each station. The data recorded on each sonde were retrieved to a field laptop computer at each station visit. The feasibility of transmitting these data in near-real time to a central processing point for dissemination on the World-Wide Web was tested successfully. Data collected at all eight stations indicate that a number of factors affect the dissolved-oxygen concentration in the streams and rivers monitored. These factors include: temperature, biological activity, nutrient runoff, and weather (storm runoff). During brief periods usually in late summer, dissolved-oxygen concentrations in half or more of the eight streams and rivers monitored were below the 5 milligrams per liter minimum established by the Illinois Pollution Control Board to protect aquatic life. Because the streams monitored represent a wide range in water-quality and environmental conditions, including diffuse (non-point) runoff and wastewater-effluent contributions, this result indicates that deleterious low dissolved-oxygen concentrations during late summer may be widespread in Illinois streams.

Atmospheric Mining in the Outer Solar System: Outer Planet Orbital Transfer and Lander Analyses

NASA Technical Reports Server (NTRS)

Palaszewski, Bryan

2016-01-01

High energy propellants for human lunar missions are analyzed, focusing on very advanced ozone and atomic hydrogen. One of the most advanced launch vehicle propulsion systems, such as the Space Shuttle Main Engine (SSME), used hydrogen and oxygen and had a delivered specific impulse of 453 seconds. In the early days of the space program, other propellants (or so called metapropellants) were suggested, including atomic hydrogen and liquid ozone. Theoretical and experimental studies of atomic hydrogen and ozone were conducted beginning in the late 1940s. This propellant research may have provided screenwriters with the idea of an atomic hydrogen-ozone rocket engine in the 1950 movie, Rocketship X-M. This paper presents analyses showing that an atomic hydrogen-ozone rocket engine could produce a specific impulse over a wide range of specific impulse values reaching as high as 1,600 seconds. A series of single stage and multistage rocket vehicle analyses were conducted to find the minimum specific impulse needed to conduct high energy round trip lunar missions.

Propulsion Estimates for High Energy Lunar Missions Using Future Propellants

NASA Technical Reports Server (NTRS)

Palaszewski, Bryan A.; Bennett, Gary L.

2016-01-01

High energy propellants for human lunar missions are analyzed, focusing on very advanced ozone and atomic hydrogen. One of the most advanced launch vehicle propulsion systems, such as the Space Shuttle Main Engine (SSME), used hydrogen and oxygen and had a delivered specific impulse of 453 seconds. In the early days of the space program, other propellants (or so called metapropellants) were suggested, including atomic hydrogen and liquid ozone. Theoretical and experimental studies of atomic hydrogen and ozone were conducted beginning in the late 1940s. This propellant research may have provided screenwriters with the idea of an atomic hydrogen-ozone rocket engine in the 1950 movie, Rocketship X-M. This paper presents analyses showing that an atomic hydrogen-ozone rocket engine could produce a specific impulse over a wide range of specific impulse values reaching as high as 1,600 s. A series of single stage and multistage rocket vehicle analyses were conducted to find the minimum specific impulse needed to conduct high energy round trip lunar missions.

Incidence of First Time Stroke: A Saudi Experience.

PubMed

Al-Shenqiti, Abdullah M; Ibrahim, Sameh R; Khaled, Osama A; Ali, Abdul Rahman H; Ahmed, Mostafa S

2017-01-01

Stroke is one of the major causes of morbidity and mortality throughout the world. A number of studies were conducted in Saudi Arabia. However, there were no studies conducted in Al-Madinah Al-Munawarah city. The aim of this study was to ascertain the incidence rate of first time stroke and the age-specific incidence in both genders in Al-Madinah Al-Munawarah city. A prospective hospital based study was conducted over a 1-year period (2014). The cases were included in the study when they were admitted with a diagnosis of cerebrovascular accident. A total 164 patients (91 men and 73 women) who had first time stroke were found in this study with no significant difference between them (p = 0.565). The crude incidence rate of stroke was 13.89 per 100,000 persons. The age-specific incidence rate increased with age in the current study, where the peak was in the age group of more than 75 years old for men and women. Total crude and the age-specific rates for first time stroke patients revealed in this study were markedly lower than the range reported from the developed countries. However, they were within the range that showed previously in Saudi Arabia and Arabian Peninsula countries. © 2017 S. Karger AG, Basel.

Functionalized graphene nanomaterials: new insight into direct exfoliation of graphite with supramolecular polymers

NASA Astrophysics Data System (ADS)

Cheng, Chih-Chia; Chang, Feng-Chih; Wang, Jui-Hsu; Chen, Jem-Kun; Yen, Ying-Chieh; Lee, Duu-Jong

2015-12-01

A novel urea-cytosine end-capped polypropylene glycol (UrCy-PPG) can self-assemble into a long-range ordered lamellar microstructure on the surface of graphene, due to the strong specific interactions between UrCy-PPG and graphene. In addition, the graphene composite produced exhibits a high conductivity (~1093 S m-1) with a dramatic thermo-responsive ON/OFF resistance-switching behavior (10 consecutive cycles).A novel urea-cytosine end-capped polypropylene glycol (UrCy-PPG) can self-assemble into a long-range ordered lamellar microstructure on the surface of graphene, due to the strong specific interactions between UrCy-PPG and graphene. In addition, the graphene composite produced exhibits a high conductivity (~1093 S m-1) with a dramatic thermo-responsive ON/OFF resistance-switching behavior (10 consecutive cycles). Electronic supplementary information (ESI) available. See DOI: 10.1039/c5nr07076g

Quality of ground water in Harrison County, Mississippi, June - July 1993

USGS Publications Warehouse

Slack, L.J.; Oakley, W.T.; O'Hara, C. G.; Cooper, L.M.

1994-01-01

During June and July 1993, the U.S. Geological Survey analyzed water from 145 wells in Harrison County, southeastern Mississippi. The wells are completed in five major geologic units: the Citronelle, Graham Ferry, Pascagoula, and Hattiesburg Formations and the Catahoula Sandstone. The wells ranged from 74 to 2,410 feet in depth. Specific conductance (lab) ranged from 15 to 2,020 microsiemens per centimeter; pH (lab), from 5.9 to 9.0; color, from less than 5 to 120 platinum-cobalt units; dissolved-solids concentrations (residue on evaporation), from 20 to 1,120 milligrams per liter; chloride concentrations, from 1.9 to 470 milligrams per liter; and nitrite plus nitrate as nitrogen concentrations, from less than 0.02 to 0.85 milligram per liter. Most of the larger values of specific conductance, pH, dissolved-solids concen- trations, and chloride concentrations were from wells in the southern one-half of the county.

Electrode-active material for electrochemical batteries and method of preparation

DOEpatents

Varma, R.

1983-11-07

A battery electrode material comprises a non-stoichiometric electrode-active material which forms a redox pair with the battery electrolyte, an electrically conductive polymer present in the range of from about 2% by weight to about 5% by weight of the electrode-active material, and a binder. The conductive polymer provides improved proton or ion conductivity and is a ligand resulting in metal ion or negative ion vacancies of less than about 0.1 atom percent. Specific electrodes of nickel and lead are disclosed.

Electrode-active material for electrochemical batteries and method of preparation

DOEpatents

Varma, Ravi

1987-01-01

A battery electrode material comprising a non-stoichiometric electrode-active material which forms a redox pair with the battery electrolyte, an electrically conductive polymer present in the range of from about 2% by weight to about 5% by weight of the electrode-active material, and a binder. The conductive polymer provides improved proton or ion conductivity and is a ligand resulting in metal ion or negative ion vacancies of less than about 0.1 atom percent. Specific electrodes of nickel and lead are disclosed.

Turboelectric Aircraft Drive Key Performance Parameters and Functional Requirements

NASA Technical Reports Server (NTRS)

Jansen, Ralph H.; Brown, Gerald V.; Felder, James L.; Duffy, Kirsten P.

2016-01-01

The purpose of this paper is to propose specific power and efficiency as the key performance parameters for a turboelectric aircraft power system and investigate their impact on the overall aircraft. Key functional requirements are identified that impact the power system design. Breguet range equations for a base aircraft and a turboelectric aircraft are found. The benefits and costs that may result from the turboelectric system are enumerated. A break-even analysis is conducted to find the minimum allowable electric drive specific power and efficiency that can preserve the range, initial weight, operating empty weight, and payload weight of the base aircraft.

Turboelectric Aircraft Drive Key Performance Parameters and Functional Requirements

NASA Technical Reports Server (NTRS)

Jansen, Ralph; Brown, Gerald V.; Felder, James L.; Duffy, Kirsten P.

2015-01-01

The purpose of this presentation is to propose specific power and efficiency as the key performance parameters for a turboelectric aircraft power system and investigate their impact on the overall aircraft. Key functional requirements are identified that impact the power system design. Breguet range equations for a base aircraft and a turboelectric aircraft are found. The benefits and costs that may result from the turboelectric system are enumerated. A break-even analysis is conducted to find the minimum allowable electric drive specific power and efficiency that can preserve the range, initial weight, operating empty weight, and payload weight of the base aircraft.

Turboelectric Aircraft Drive Key Performance Parameters and Functional Requirements

NASA Technical Reports Server (NTRS)

Jansen, Ralph H.; Brown, Gerald V.; Felder, James L.; Duffy, Kirsten P.

2015-01-01

The purpose of this paper is to propose specific power and efficiency as the key performance parameters for a turboelectric aircraft power system and investigate their impact on the overall aircraft. Key functional requirements are identified that impact the power system design. Breguet range equations for a base aircraft and a turboelectric aircraft are found. The benefits and costs that may result from the turboelectric system are enumerated. A break-even analysis is conducted to find the minimum allowable electric drive specific power and efficiency that can preserve the range, initial weight, operating empty weight, and payload weight of the base aircraft.

Role of specific IgE and skin-prick testing in predicting food challenge results to baked egg

PubMed Central

Cortot, Catherine F.; Sheehan, William J.; Permaul, Perdita; Friedlander, James L.; Baxi, Sachin N.; Gaffin, Jonathan M.; Dioun, Anahita F.; Hoffman, Elaine B.; Schneider, Lynda C.

2012-01-01

Previous studies suggest that children with egg allergy may be able to tolerate baked egg. Reliable predictors of a successful baked egg challenge are not well established. We examined egg white–specific IgE levels, skin-prick test (SPT) results, and age as predictors of baked egg oral food challenge (OFC) outcomes. We conducted a retrospective chart review of children, aged 2–18 years, receiving an egg white–specific IgE level, SPT, and OFC to baked egg from 2008 to 2010. Fifty-two oral baked egg challenges were conducted. Of the 52 challenges, 83% (n = 43) passed and 17% (n = 9) failed, including 2 having anaphylaxis. Median SPT wheal size was 12 mm (range, 0–35 mm) for passed challenges and 17 mm (range, 10–30 mm) for failed challenges (p = 0.091). The negative predictive value for passing the OFC was 100% (9 of 9) if SPT wheal size was <10 mm. Median egg white–specific IgE was 2.02 kU/L (range, <0.35–13.00 kU/L) for passed challenges and 1.52 kU/L (range, 0.51–6.10 kU/L) for failed challenges (p = 0.660). Receiver operating characteristic (ROC) curve analysis for SPT revealed an area under the curve (AUC) of 0.64. ROC curve analysis for egg white–specific IgE revealed an AUC of 0.63. There was no significant difference in age between patients who failed and those who passed (median = 8.8 years versus 7.0 years; p = 0.721). Based on our sample, SPT, egg white–specific IgE and age are not good predictors of passing a baked egg challenge. However, there was a trend for more predictability with SPT wheal size. PMID:22584194

DOE Office of Scientific and Technical Information (OSTI.GOV)

Karydis, D.A.; Boghosian, S.; Fehrmnn, R.

The specific conductivities of the sulfuric acid catalyst model system M[sub 2]S[sub 2]O[sub 7]-V[sub 2]O[sub 5] (M = 80% K + 20% Na) were measured at 14 different compositions in the range x[sub V[sub 2]O[sub 5

Measurement of the Thermal Properties of a Metal Using a Relaxation Method

ERIC Educational Resources Information Center

Fox, John N.; McMaster, Richard H.

1975-01-01

An undergraduate experiment is described which employs a relaxation method for the measurement of the thermal conductivity and specific heat of a metallic sample in a temperature range of 0-100 degrees centigrade. (Author/CP)

Creating Change in the Use of Information and Communications Technology by Female Islamic Studies Teachers in Saudi Arabia

ERIC Educational Resources Information Center

Alsharidah, Majed

2018-01-01

The range of research undertaken in the area of the use of information and communications technology (ICT) in the teaching-learning process indicates the importance of the need for such a tool. Paradoxically, there is lack of emphasis on Islamic teachers and specifically female Islamic teachers. This study was conducted in 2017 using a range of…

Determination of the saturated film conductivity to improve the EMFX model in describing the soil hydraulic properties over the entire moisture range

NASA Astrophysics Data System (ADS)

Wang, Yunquan; Ma, Jinzhu; Guan, Huade; Zhu, Gaofeng

2017-06-01

Difficulty in measuring hydraulic conductivity, particularly under dry conditions, calls for methods of predicting the conductivity from easily obtained soil properties. As a complement to the recently published EMFX model, a method based on two specific suction conditions is proposed to estimate saturated film conductivity from the soil water retention curve. This method reduces one fitting parameter in the previous EMFX model, making it possible to predict the hydraulic conductivity from the soil water retention curve over the complete moisture range. Model performance is evaluated with published data of soils in a broad texture range from sand to clay. The testing results indicate that 1) the modified EMFX model (namely the EMFX-K model), incorporating both capillary and adsorption forces, provides good agreement with the conductivity data over the entire moisture range; 2) a value of 0.5 for the tortuosity factor in the EMFX-K model as that in the Mualem's model gives comparable estimation of the relative conductivity associated with the capillary force; and 3) a value of -1.0 × 10-20 J for the Hamaker constant, rather than the commonly used value of -6.0 × 10-20 J, appears to be more appropriate to represent solely the effect of the van der Waals forces and to predict the film conductivity. In comparison with the commonly used van Genuchten-Mualem model, the EMFX-K model significantly improves the prediction of hydraulic conductivity under dry conditions. The sensitivity analysis result suggests that the uncertainty in the film thickness estimation is important in explaining the model underestimation of hydraulic conductivity for the soils with fine texture, in addition to the uncertainties from the measurements and the model structure. High quality data that cover the complete moisture range for a variety of soil textures are required to further test the method.

Distribution and ecology of Ostracodes from 34 lakes on the Tibetan Plateau

NASA Astrophysics Data System (ADS)

Peng, P.; Fürstenberg, S.; Frenzel, P.; Guo, Y.; Zhu, L.; Gifty-Akita, L.

2013-12-01

Abstract Ostracodes (bivalved Crustaceans) inhabit nearly all aquatic environments from the marine realm to continental freshwater bodies and represent important bio-indicators since their calcific shells are readily preserved in the lake sediments in high numbers. Furthermore they record a plentifulness of information about palaeoenvironments. This data can be used for reconstructing climatic changes on the Tibetan Plateau. We obtained 112 surface sediment samples from 34 lakes on the plateau to investigate distribution and ecology of ostracodes for understanding the implications of aquatic environmental factors on the distribution of ostracodes. There were 12 species identified: Candona candida, Candona xizangensis, Fabaeformiscandona gyirongensis, Potamocypris villosa, Heterocypris sp. , Eucypris gyirongensis, Ilyocypris sp. , Cytherissa lacustris, Leucuocythere dorsotuberosa, Leucocytherella sinensis, and Limnocythere inopinata. Corresponding environmental factors including water depth, specific conductivity, temperature, pH and dissolved oxygen were monitored in various lakes. The range of specific conductivity was between 275 and 202000 μS/cm. A Principle Component Analysis (PCA) depicted that ostracode diversity gained high relations with specific conductivity (r = -0.43) and dissolved oxygen (r = 0.43). This indicated that specific conductivity could be the main factor driving the distribution of ostracodes on the Tibetan Plateau. Keywords: Ostracodes, Tibetan Plateau, lacustrine sediment, ecology, diversity

Ground-water geochemistry of the Albuquerque-Belen Basin, central New Mexico

USGS Publications Warehouse

Anderholm, S.K.

1988-01-01

The purpose of this study was to define the areal distribution of different water types, use the distribution to help define the groundwater flow system, and identify processes resulting in differences in groundwater quality in the Albuquerque-Belen Basin in central New Mexico. The chemistry of surface water inflow from adjacent areas, which infiltrates and recharges the aquifer along the basin margin, affects the groundwater quality in the eastern and southeastern areas of the basin. Groundwater in the eastern area generally has a specific conductance less than 400 microsiemens, and calcium and bicarbonate are the dominant ions. Mixing of recharge, groundwater inflow, and surface inflow from adjacent areas, which have different chemical compositions, is the major process affecting groundwater quality in the southwestern, western, and northern areas of the basin. In these areas, there is a large range in specific conductance and distribution of dissolved ions. Groundwater quality in the Rio Grande valley is affected by the infiltration of excess irrigation water. The excess irrigation water generally has a larger specific conductance than other groundwater in the valley, so mixing of these waters results in shallow groundwater generally having larger specific conductance than the deeper groundwater. (USGS)

Potentiometric surface and specific conductance of the Sparta and Memphis aquifers in eastern Arkansas, 1995

USGS Publications Warehouse

Stanton, Gregory P.

1997-01-01

The Sparta and Memphis aquifers in eastern and south-central Arkansas are a major source of water for industrial, public supply, and agricultural uses. An estimated 240 million gallons per day was withdrawn from the Sparta and Memphis aquifers in 1995, an increase of about 17 million gallons per day from 1990. During the spring and early summer of 1995, the water level in the Sparta and Memphis aquifers was measured in 145 wells, the specific conductance of 101 ground-water samples collected from those aquifers was measured. Maps of areal distribution of potentiometric surface and specific conductance generated from these data reveal spatial trends in these parameters across the eastern and south-central Arkansas study area. The altitude of the potentiometric surface ranged from about 206 feet below sea level in Union County to about 307 feet above sea level in Saline County. The potentiometric surface of the Sparta and Memphis aquifers contains cones of depression descending below sea level in the central and southern portions of the study area, and a potentiometric high along the western study area boundary. Major recharge areas exhibit potentiometric highs greater than 200 feet above sea level and specific conductance values less than 200 microsiemens per centimeter, and generally are located in the outcrop/subcrop areas on the southern one-third of the western boundary and the northern portion of the study area. The regional direction of ground-water flow is from the north and west to the south and east, away from the outcrop and subcrop and northern regions, except near areas affected by intense ground-water withdrawals; such areas are manifested by large cones of depression centered in Columbia, Jefferson, and Union Counties. The cones of depression in adjoining Columbia and Union Counties are coalescing at or near sea level. The lowest water level measured was about 206 feet below sea level in Union County. Increased specific conductance values were measured in the areas of the cones of depression in Columbia and Union Counties. The cones of depression centered in Jefferson County coincides with an elongate area where ground water in the aquifer has low specific conductance. This area extends eastward from the outcrop/subcrop region of recharge. This extension of ground water with low specific conductance possibly indicates increased ground-water movement to the east-southeast from the outcrop/subcrop area induced by ground- water withdrawals in Jefferson County. Specific conductance increases markedly to the northeast and gradually to the south of this area. Long-term hydrographs of eight wells in the study areas, during the period 1970-1995, reveal water-level declines ranging from less than 0.5 foot per year in Phillips County to more than 2.0 feet per year in Union County. Water-level declines of greater than 1.5 feet per year generally are associated with the cones of depression centered in Columbia, Jefferson, and Union Counties.

Statistical summaries of water-quality data for two coal areas of Jackson County, Colorado

USGS Publications Warehouse

Kuhn, Gerhard

1982-01-01

Statistical summaries of water-quality data are compiled for eight streams in two separate coal areas of Jackson County, Colo. The quality-of-water data were collected from October 1976 to September 1980. For inorganic constituents, the maximum, minimum, and mean concentrations, as well as other statistics are presented; for minor elements, only the maximum, minimum, and mean values are included. Least-squares equations (regressions) are also given relating specific conductance of the streams to the concentration of the major ions. The observed range of specific conductance was 85 to 1,150 micromhos per centimeter for the eight sites. (USGS)

Delineation of fractures, foliation, and groundwater-flow zones of the bedrock at the Harlem River Tunnel in northern New York County, New York

USGS Publications Warehouse

Stumm, Frederick; Chu, Anthony; Joesten, Peter K.; Noll, Michael L.; Como, Michael D.

2013-01-01

Advanced borehole-geophysical methods were used to investigate the hydrogeology of the crystalline bedrock in 36 boreholes on the northernmost part of New York County, New York, for the construction of a utilities tunnel beneath the Harlem River. The borehole-logging techniques were used to delineate bedrock fractures, foliation, and groundwater-flow zones in test boreholes at the site. Fracture indexes of the deep boreholes ranged from 0.65 to 0.76 per foot. Most of the fracture populations had either northwest to southwest or east to southeast dip azimuths with moderate dip angles. The mean foliation dip azimuth ranged from 100º to 124º southeast with dip angles of 52º to 60º. Groundwater appears to flow through an interconnected network of fractures that are affected by tidal variations from the nearby Harlem River and tunnel construction dewatering operations. The transmissivities of the 3 boreholes tested (USGS-1, USGS-3, and USGS-4), calculated from specific capacity data, were 2, 48, and 30 feet squared per day (ft2/d), respectively. The highest transmissivities were observed in wells north and west of the secant ring. Three borehole-radar velocity tomograms were collected. In the USGS-1 and USGS-4 velocity tomogram there are two areas of low radar velocity. The first is at the top of the tomogram and runs from 105 ft below land surface (BLS) at USGS-4 and extends to 125 ft BLS at USGS-1, the second area is centered at a depth of 150 ft BLS at USGS-1 and 135 to 150 ft BLS at USGS-4. Field measurements of specific conductance of 14 boreholes under ambient conditions at the site indicate an increase in conductivity toward the southwest part of the site (nearest the Harlem River). Specific conductance ranged from 107 microsiemens per centimeter (μS/cm) (borehole 63C) to 11,000 μS/cm (borehole 79B). The secant boreholes had the highest specific conductance.

Bed conduction impact on fiber optic distributed temperature sensing water temperature measurements

NASA Astrophysics Data System (ADS)

O'Donnell Meininger, T.; Selker, J. S.

2015-02-01

Error in distributed temperature sensing (DTS) water temperature measurements may be introduced by contact of the fiber optic cable sensor with bed materials (e.g., seafloor, lakebed, streambed). Heat conduction from the bed materials can affect cable temperature and the resulting DTS measurements. In the Middle Fork John Day River, apparent water temperature measurements were influenced by cable sensor contact with aquatic vegetation and fine sediment bed materials. Affected cable segments measured a diurnal temperature range reduced by 10% and lagged by 20-40 min relative to that of ambient stream temperature. The diurnal temperature range deeper within the vegetation-sediment bed material was reduced 70% and lagged 240 min relative to ambient stream temperature. These site-specific results illustrate the potential magnitude of bed-conduction impacts with buried DTS measurements. Researchers who deploy DTS for water temperature monitoring should understand the importance of the environment into which the cable is placed on the range and phase of temperature measurements.

Technical Note: Bed conduction impact on fiber optic DTS water temperature measurements

NASA Astrophysics Data System (ADS)

O'Donnell Meininger, T.; Selker, J. S.

2014-07-01

Error in Distributed Temperature Sensor (DTS) water temperature measurements may be introduced by contact of the fiber optic cable sensor with bed materials (e.g., seafloor, lakebed, stream bed). Heat conduction from the bed materials can affect cable temperature and the resulting DTS measurements. In the Middle Fork John Day River, apparent water temperature measurements were influenced by cable sensor contact with aquatic vegetation and fine sediment bed materials. Affected cable segments measured a diurnal temperature range reduced by 10% and lagged by 20-40 min relative to that of ambient stream temperature. The diurnal temperature range deeper within the vegetation-sediment bed material was reduced 70% and lagged 240 min relative to ambient stream temperature. These site-specific results illustrate the potential magnitude of bed-conduction impacts with buried DTS measurements. Researchers who deploy DTS for water temperature monitoring should understand the importance of the environment into which the cable is placed on the range and phase of temperature measurements.

The effect of targeted wide age range SIAs in reducing measles incidence in the African Region.

PubMed

Masresha, Balcha; Luce, Richard; Katsande, Regis; Fall, Amadou; Eshetu, Meseret; Mihigo, Richard

2017-01-01

Periodic measles supplemental immunisation activities (SIAs) increase population immunity and thereby reduce the pool of accumulated susceptible children. They are typically conducted every 2 - 4 years, and most often target children up to five years of age. Between 2012 and 2015, after surveillance data indicated a shift in the epidemiological profile of measles towards older age groups, 11 countries were supported to conduct wide age range SIAs based on their local epidemiological patterns. Six other countries conducted SIAs with measles-rubella vaccines targeting ages 9 months to 14 years as an initial step of introducing rubella vaccine into the immunization program. In subsequent years, the incidence of confirmed measles dropped significantly in 13 of the 17 countries reviewed. The findings emphasize the importance of well-functioning surveillance systems, and the benefits of using of surveillance data to determine the specific target age-range for periodic SIAs to accelerate progress towards measles elimination.

The effect of targeted wide age range SIAs in reducing measles incidence in the African Region

PubMed Central

Masresha, Balcha; Luce, Richard; Katsande, Regis; Fall, Amadou; Eshetu, Meseret; Mihigo, Richard

2017-01-01

Periodic measles supplemental immunisation activities (SIAs) increase population immunity and thereby reduce the pool of accumulated susceptible children. They are typically conducted every 2 – 4 years, and most often target children up to five years of age. Between 2012 and 2015, after surveillance data indicated a shift in the epidemiological profile of measles towards older age groups, 11 countries were supported to conduct wide age range SIAs based on their local epidemiological patterns. Six other countries conducted SIAs with measles-rubella vaccines targeting ages 9 months to 14 years as an initial step of introducing rubella vaccine into the immunization program. In subsequent years, the incidence of confirmed measles dropped significantly in 13 of the 17 countries reviewed. The findings emphasize the importance of well-functioning surveillance systems, and the benefits of using of surveillance data to determine the specific target age-range for periodic SIAs to accelerate progress towards measles elimination. PMID:29296148

The conductivity measurements applied for the evaluation of controlled release of chlorhexidine from thermosensitive N-isopropylacrylamide derivative microgels.

PubMed

Musiał, Witold; Kokol, Vanja; Voncina, Bojana

2009-01-01

The aim of the work was the evaluation of the conductivity changes in aqueous environment, consisting of chlorhexidine, and N-isopropylacrylamide derivative microgel, during increasing the temperature between 25 degrees C and 42 degrees C, as a prerequisite to develop the this microgel for controlled release of chlorhexidine, when alterations in temperature are involved. Conductivity of studied systems underwent specific alterations, when temperature increased. For the system with polymer PNM I the values of conductivity were in the range 104,47 microS/cm - 134,70 microS/ cm, for temperature range 25 degrees C and 42 degrees C. In the case of PNM II - CX system, respective values reached 91,75 microS/cm - 135,95 microS/cm. The lowest conductivity values were observed when PNM III - CX mixture was studied: 96,90 microS/cm and 117,37 microS/cm. When a complex of derivatives of N-isopropylacrylamide with chlorhexidine undergoes thermal alteration, there is a potential to obtain controlled release of chlorhexidine from the polymeric bead in the range between 25 degrees C and 42 degrees C. The affinity of chlorhexidine to the polymer may be assessed in this systems applying the conductivity measurements. The solubility of chlorhexidine in the polymeric systems should be in future evaluated, to determine role of this factor in the conductivity alterations.

Hydrologic data for the Big Spring basin, Clayton County, Iowa, water year 1991

USGS Publications Warehouse

Kalkhoff, S.J.; Kuzniar, R.L.

1994-01-01

Stream discharge, specific conductance, pH, and water temperature were monitored continuously, and monthly water-quality samples were collected at a site on Roberts Creek and at Big Spring. Nitrite plus nitrate as nitrogen concentrations in 27 samples from Roberts Creek at the point where it leaves the study area ranged from 1.8 to 22 mg/L. Herbicide concentrations in 26 samples from the Roberts Creek site ranged from less than 0.10 μg/L (micrograms per liter) to 43 μg/L. Alachlor was detected in 42 percent of the samples; atrazine in 92 percent; and cyanazine and metolachlor in 35 percent of the samples. The total suspended-sediment load discharged in Roberts Creek was about 160,000 tons. At Big Spring, the ground-water discharge point, the daily mean specific conductance ranged from 414 to 788 microsiemens per centimeter at 25 degrees Celsius, the daily median pH ranged from 6.7 to 7.1, and the daily mean water temperature ranged from 8.5 to 13.0 degrees Celsius. Concentrations of nitrite plus nitrate as nitrogen in 23 samples ranged from 4.2 to 17 mg/L. The total measured suspended-sediment discharged from Big Spring was about 17,000 tons. Alachlor was detected in 26 percent; atrazine in 100 percent; cyanazine in 26 percent, and metolachlor in 9 percent of the samples. The maximum atrazine concentration was 16 μg/L.

The stability of hydrogen ion and specific conductance in filtered wet-deposition samples stored at ambient temperatures

USGS Publications Warehouse

Gordon, J.D.; Schroder, L.J.; Morden-Moore, A. L.; Bowersox, V.C.

1995-01-01

Separate experiments by the U.S. Geological Survey (USGS) and the Illinois State Water Survey Central Analytical Laboratory (CAL) independently assessed the stability of hydrogen ion and specific conductance in filtered wet-deposition samples stored at ambient temperatures. The USGS experiment represented a test of sample stability under a diverse range of conditions, whereas the CAL experiment was a controlled test of sample stability. In the experiment by the USGS, a statistically significant (?? = 0.05) relation between [H+] and time was found for the composited filtered, natural, wet-deposition solution when all reported values are included in the analysis. However, if two outlying pH values most likely representing measurement error are excluded from the analysis, the change in [H+] over time was not statistically significant. In the experiment by the CAL, randomly selected samples were reanalyzed between July 1984 and February 1991. The original analysis and reanalysis pairs revealed that [H+] differences, although very small, were statistically different from zero, whereas specific-conductance differences were not. Nevertheless, the results of the CAL reanalysis project indicate there appears to be no consistent, chemically significant degradation in sample integrity with regard to [H+] and specific conductance while samples are stored at room temperature at the CAL. Based on the results of the CAL and USGS studies, short-term (45-60 day) stability of [H+] and specific conductance in natural filtered wet-deposition samples that are shipped and stored unchilled at ambient temperatures was satisfactory.

Comparison of sensitivity and specificity among 15 criteria for chronic inflammatory demyelinating polyneuropathy.

PubMed

Breiner, Ari; Brannagan, Thomas H

2014-07-01

There have been 15 formal sets of criteria published for the diagnosis of CIDP. No study to date has compared the sensitivity and specificity of all published criteria in the same patient population. We conducted a retrospective chart review of patients with CIDP (n = 56) and controls with diabetic polyneuropathy (n = 37) or amyotrophic lateral sclerosis (n = 39) who were followed in an academic neuromuscular practice. The sensitivity and specificity of each CIDP criterion was calculated, including clinical, laboratory, and electrodiagnostic components. Sensitivities ranged from 1.8% to 87.5%; the Dyck (87.5%), Neuropathy Association (75%), and European Federation of Neurological Societies (EFNS; 73.2%) criteria ranked highest. Specificities ranged from 65.6% to 100% and, among the 3 most sensitive criteria, the EFNS (90.8%) and Neuropathy Association (82.9%) criteria were most specific. In our patient population, the EFNS and Neuropathy Association criteria stand out due to high sensitivity and specificity. Copyright © 2013 Wiley Periodicals, Inc.

Thermophysical Properties of 60-NITINOL for Mechanical Component Applications

NASA Technical Reports Server (NTRS)

Stanford, Malcolm K.

2012-01-01

The linear thermal expansion coefficient, specific heat capacity, electrical resistivity and thermal conductivity of 60- NITINOL were studied over a range of temperatures representing the operating environment of an oil-lubricated bearing. The behavior of this material appears to follow wellestablished theories applicable to either metal alloys, in general, or to intermetallic compounds, more specifically and the measured data were found to be comparable to those for conventional bearing alloys.

Three decades of disasters: a review of disaster-specific literature from 1977-2009.

PubMed

Smith, Erin; Wasiak, Jason; Sen, Ayan; Archer, Frank; Burkle, Frederick M

2009-01-01

The potential for disasters exists in all communities. To mitigate the potential catastrophes that confront humanity in the new millennium, an evidence-based approach to disaster management is required urgently. This study moves toward such an evidence-based approach by identifying peer-reviewed publications following a range of disasters and events over the past three decades. Peer-reviewed, event-specific literature was identified using a comprehensive search of the electronically indexed database, MEDLINE (1956-January 2009). An extended comprehensive search was conducted for one event to compare the event-specific literature indexed in MEDLINE to other electronic databases (EMBASE, CINAHL, AMED, CENTRAL, Psych Info, Maternity and Infant Care, EBM Reviews). Following 25 individual disasters or overwhelming crises, a total of 2,098 peer-reviewed, event-specific publications were published in 789 journals (652 publications following disasters/events caused by natural hazards, 966 following human-made/technological disasters/events, and 480 following conflict/complex humanitarian events).The event with the greatest number of peer-reviewed, event-specific publications was the 11 September 2001 terrorist attacks (686 publications). Prehospital and Disaster Medicine published the greatest number of peer-reviewed, event-specific publications (54), followed by Journal of Traumatic Stress (42), Military Medicine (40), and Psychiatric Services (40). The primary topics of event-specific publications were mental health, medical health, and response. When an extended, comprehensive search was conducted for one event, 75% of all peer-reviewed, event-specific publications were indexed in MEDLINE. A broad range of multi-disciplinary journals publish peer reviewed, event-specific publications. While the majority of peer-reviewed, event-specific literature is indexed in MEDLINE, comprehensive search strategies should include EMBASE to increase yield.

Is it getting hot in here? Adjustment of hydraulic parameters in six boreal and temperate tree species after 5 years of warming.

PubMed

McCulloh, Katherine A; Petitmermet, Joshua; Stefanski, Artur; Rice, Karen E; Rich, Roy L; Montgomery, Rebecca A; Reich, Peter B

2016-12-01

Global temperatures (T) are rising, and for many plant species, their physiological response to this change has not been well characterized. In particular, how hydraulic parameters may change has only been examined experimentally for a few species. To address this, we measured characteristics of the hydraulic architecture of six species growing in ambient T and ambient +3.4 °C T plots in two experimentally warmed forest sites in Minnesota. These sites are at the temperate-boreal ecotone, and we measured three species from each forest type. We hypothesized that relative to boreal species, temperate species near their northern range border would increase xylem conduit diameters when grown under elevated T. We also predicted a continuum of responses among wood types, with conduit diameter increases correlating with increases in the complexity of wood structure. Finally, we predicted that increases in conduit diameter and specific hydraulic conductivity would positively affect photosynthetic rates and growth. Our results generally supported our hypotheses, and conduit diameter increased under elevated T across all species, although this pattern was driven predominantly by three species. Two of these species were temperate angiosperms, but one was a boreal conifer, contrary to predictions. We observed positive relationships between the change in specific hydraulic conductivity and both photosynthetic rate (P = 0.080) and growth (P = 0.012). Our results indicate that species differ in their ability to adjust hydraulically to increases in T. Specifically, species with more complex xylem anatomy, particularly those individuals growing near the cooler edge of their range, appeared to be better able to increase conduit diameters and specific hydraulic conductivity, which permitted increases in photosynthesis and growth. Our data support results that indicate individual's ability to physiologically adjust is related to their location within their species range, and highlight that some wood types may adjust more easily than others. © 2016 John Wiley & Sons Ltd.

Evaluative procedures to detect, characterize, and assess the severity of diabetic neuropathy.

PubMed

Dyck, P J

1991-01-01

Minimal criteria for diabetic neuropathy need to be defined and universally applied. Standardized evaluative procedures need to be agreed and normal ranges determined from healthy volunteers. Types and stages of neuropathy should be established and assessments performed on representative populations of both Type 1 and Type 2 diabetic patients. Potential minimal criteria include absent ankle reflexes and vibratory sensation, and abnormalities of nerve conduction. However, the preferred criterion is the identification of more than two statistically defined abnormalities among symptoms and deficits, nerve conduction, quantitative sensory examination or quantitative autonomic examination. Various evaluative procedures are available. Symptoms should be assessed and scores can be assigned to neurological deficits. However, assessments of nerve conduction provide the most specific, objective, sensitive, and repeatable procedures, although these may be the least meaningful. Many techniques are available for quantitative sensory examination, but are poorly standardized and normal values are not available. For quantitative autonomic examination, tests are available for the adequacy of cardiovascular and peripheral vascular reflexes and increasingly for other autonomic functions. In any assessment of nerve function the conditions should be optimized and standardized, and stimuli defined. Specific instructions should be given and normal ranges established in healthy volunteers.

Oxidation resistance, thermal conductivity, and spectral emittance of fully dense zirconium diboride with silicon carbide and tantalum diboride additives

NASA Astrophysics Data System (ADS)

Van Laningham, Gregg Thomas

Zirconium diboride (ZrB2) is a ceramic material possessing ultra-high melting temperatures. As such, this compound could be useful in the construction of thermal protection systems for aerospace applications. This work addresses a primary shortcoming of this material, namely its propensity to destructively oxidize at high temperatures, as well as secondary issues concerning its heat transport properties. To characterize and improve oxidation properties, thermogravimetric studies were performed using a specially constructed experimental setup. ZrB 2-SiC two-phase ceramic composites were isothermally oxidized for ~90 min in flowing air in the range 1500-1900°C. Specimens with 30 mol% SiC formed distinctive reaction product layers which were highly protective; 28 mol% SiC - 6 mol% TaB2 performed similarly. At higher temperatures, specimens containing lower amounts of SiC were shown to be non-protective, whereas specimens containing greater amounts of SiC produced unstable oxide layers due to gas evolution. Oxide coating thicknesses calculated from weight loss data were consistent with those measured from SEM micrographs. In order to characterize one aspect of the materials' heat transport properties, the thermal diffusivities of ZrB2-SiC composites were measured using the laser flash technique. These were converted to thermal conductivities using temperature dependent specific heat and density data; thermal conductivity decreased with increasing temperature over the range 25-2000°C. The composition with the highest SiC content showed the highest thermal conductivity at room temperature, but the lowest at temperatures in excess of ~400°C, because of the greater temperature sensitivity of the thermal conductivity of the SiC phase, as compared to more electrically-conductive ZrB2. Subsequent finite difference calculations were good predictors of multi-phase thermal conductvities for the compositions examined. The thermal conductivities of pure ZrB2 as a function of temperature were back-calculated from the experimental results for the multi-phase materials, and literature thermal conductivities of the other two phases. This established a relatively constant thermal conductivity of 88-104 W·K over the evaluated temperature range. Further heat transport characterization was performed using pre-oxidized, directly resistively heated ZrB2-30 mol% SiC ribbon specimens under the observation of a spectral radiometer. The ribbons were heated and held at specific temperatures over the range 1100-1330°C in flowing Ar, and normal spectral emittance values were recorded over the 1-6 μm range with a resolution of 10 nm. The normal spectral emittance was shown to decrease with loss of the borosilicate layer over the course of the data collection time periods. This change was measured and compensated for to produce traces showing the emittance of the oxidized composition rising from ~0.7 to ~0.9 over the range of wavelengths measured (1-6 μm).

Thermal Property Measurement of Semiconductor Melt using Modified Laser Flash Method

NASA Technical Reports Server (NTRS)

Lin, Bochuan; Zhu, Shen; Ban, Heng; Li, Chao; Scripa, Rosalla N.; Su, Ching-Hua; Lehoczky, Sandor L.

2003-01-01

This study further developed standard laser flash method to measure multiple thermal properties of semiconductor melts. The modified method can determine thermal diffusivity, thermal conductivity, and specific heat capacity of the melt simultaneously. The transient heat transfer process in the melt and its quartz container was numerically studied in detail. A fitting procedure based on numerical simulation results and the least root-mean-square error fitting to the experimental data was used to extract the values of specific heat capacity, thermal conductivity and thermal diffusivity. This modified method is a step forward from the standard laser flash method, which is usually used to measure thermal diffusivity of solids. The result for tellurium (Te) at 873 K: specific heat capacity 300.2 Joules per kilogram K, thermal conductivity 3.50 Watts per meter K, thermal diffusivity 2.04 x 10(exp -6) square meters per second, are within the range reported in literature. The uncertainty analysis showed the quantitative effect of sample geometry, transient temperature measured, and the energy of the laser pulse.

Daily and seasonal variability of pH, dissolved oxygen, temperature, and specific conductance in the Colorado River between the forebay of Glen Canyon, Dam and Lees Ferry, northeastern Arizona, 1998-99

USGS Publications Warehouse

Flynn, Marilyn E.; Hart, Robert J.; Marzolf, G. Richard; Bowser, Carl J.

2001-01-01

The productivity of the trout fishery in the tailwater reach of the Colorado River downstream from Glen Canyon Dam depends on the productivity of lower trophic levels. Photosynthesis and respiration are basic biological processes that control productivity and alter pH and oxygen concentration. During 1998?99, data were collected to aid in the documentation of short- and long-term trends in these basic ecosystem processes in the Glen Canyon reach. Dissolved-oxygen, temperature, and specific-conductance profile data were collected monthly in the forebay of Glen Canyon Dam to document the status of water chemistry in the reservoir. In addition, pH, dissolved-oxygen, temperature, and specific-conductance data were collected at five sites in the Colorado River tailwater of Glen Canyon Dam to document the daily, seasonal, and longitudinal range of variation in water chemistry that could occur annually within the Glen Canyon reach.

A steady-state model of spreading depression predicts the importance of an unknown conductance in specific dendritic domains.

PubMed

Makarova, Julia; Ibarz, José M; Canals, Santiago; Herreras, Oscar

2007-06-15

Spreading depression (SD) is a pathological wave of transient neuronal inactivation. We recently reported that the characteristic sustained complete depolarization is restricted to specific cell domains where the input resistance (R(in)) first becomes negligible before achieving partial recovery, whereas in adjacent, more polarized membranes it drops by much less. The experimental study of the participating membrane channels is hindered by their mixed contribution and heterogeneous distribution. Therefore, we derived a biophysical model to analyze the conductances that replicate the subcellular profile of R(in) during SD. Systematic variation of conductance densities far beyond the ranges reported failed to fit the experimental values. Besides standard potassium, sodium, and Glu-mediated conductances, the initial opening and gradual closing of an as yet undetermined large conductance is required to account for the evolution of R(in). Potassium conductances follow in the relative contribution and their closing during the late phase is also predicted. Large intracellular potential gradients from zero to rest are readily sustained between shunted and adjacent SD-spared membranes, which remain electroregenerative. The gradients are achieved by a combination of high-conductance subcellular domains and transmembrane ion redistribution in extended but discrete dendritic domains. We conclude that the heterogeneous subcellular behavior is due to local membrane properties, some of which may be specifically activated under extreme SD conditions.

Thermophysical Property Models for Lunar Regolith

NASA Technical Reports Server (NTRS)

Schreiner, Samuel S.; Dominguez, Jesus A.; Sibille, Laurent; Hoffman, Jeffrey A.

2015-01-01

We present a set of models for a wide range of lunar regolith material properties. Data from the literature are t with regression models for the following regolith properties: composition, density, specific heat, thermal conductivity, electrical conductivity, optical absorption length, and latent heat of melting/fusion. These models contain both temperature and composition dependencies so that they can be tailored for a range of applications. These models can enable more consistent, informed analysis and design of lunar regolith processing hardware. Furthermore, these models can be utilized to further inform lunar geological simulations. In addition to regression models for each material property, the raw data is also presented to allow for further interpretation and fitting as necessary.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bauer, Stephen J.; Flint, Gregory Mark

Accurate knowledge of thermophysical properties of concrete is considered extremely important for meaningful models to be developed of scenarios wherein the concrete is rapidly heated. Test of solid propellant burns on samples of concrete from Launch Complex 17 of the Cape Canaveral show spallation and fragmentation. In response to the need for accurate modeling scenarios of these observations, an experimental program to determine the permeability and thermal properties of the concrete was developed. Room temperature gas permeability measurements of Launch Complex 17 of the Cape Canaveral concrete dried at 50°C yield permeability estimates of 0.07mD (mean), and thermal properties (thermalmore » conductivity, diffusivity, and specific heat) were found to vary with temperatures from room temperature to 300°C. Thermal conductivity ranges from 1.7-1.9 W/mK at 50°C to 1.0-1.15 W/mK at 300°C, thermal diffusivity ranges from 0.75-0.96 mm 2/s at 50°C to 0.44-0.58 mm 2/s at 300°C, and specific heat ranges from 1.76-2.32 /m 3K to 2.00-2.50 /m 3K at 300°C.« less

Water-Quality Characteristics for Sites in the Tongue, Powder, Cheyenne, and Belle Fourche River Drainage Basins, Wyoming and Montana, Water Years 2001-05, with Temporal Patterns of Selected Long-Term Water-Quality Data

USGS Publications Warehouse

Clark, Melanie L.; Mason, Jon P.

2007-01-01

Water-quality sampling was conducted regularly at stream sites within or near the Powder River structural basin in northeastern Wyoming and southeastern Montana during water years 2001-05 (October 1, 2000, to September 30, 2005) to characterize water quality in an area of coalbed natural gas development. The U.S. Geological Survey, in cooperation with the Wyoming Department of Environmental Quality, characterized the water quality at 22 sampling sites in the Tongue, Powder, Cheyenne, and Belle Fourche River drainage basins. Data for general hydrology, field measurements, major-ion chemistry, and selected trace elements were summarized, and specific conductance and sodium-adsorption ratios were evaluated for relations with streamflow and seasonal variability. Trend analysis for water years 1991-2005 was conducted for selected sites and constituents to assess change through time. Average annual runoff was highly variable among the stream sites. Generally, streams that have headwaters in the Bighorn Mountains had more runoff as a result of higher average annual precipitation than streams that have headwaters in the plains. The Powder River at Moorhead, Mont., had the largest average annual runoff (319,000 acre-feet) of all the sites; however, streams in the Tongue River drainage basin had the highest runoff per unit area of the four major drainage basins. Annual runoff in all major drainage basins was less than average during 2001-05 because of drought conditions. Consequently, water-quality samples collected during the study period may not represent long-term water-quality con-ditions for all sites. Water-quality characteristics were highly variable generally because of streamflow variability, geologic controls, and potential land-use effects. The range of median specific-conductance values among sites was smallest in the Tongue River drainage basin. Median values in that basin ranged from 643 microsiemens per centimeter at 25 degrees Celsius (?S/cm at 25?C) on the Tongue River to 1,460 ?S/cm at 25?C on Prairie Dog Creek. The Tongue River drainage basin has the largest percentage of area underlain by Mesozoic-age and older rocks and by more resistant rocks. In addition, the higher annual precipitation and a steeper gradient in this basin compared to basins in the plains produce relatively fast stream velocities, which result in a short contact time between stream waters and basin materials. The Powder River drainage basin, which has the largest drainage area and most diverse site conditions, had the largest range of median specific-conductance values among the four major drainage basins. Median values in that basin ranged from 680 ?S/cm at 25?C on Clear Creek to 5,950 ?S/cm at 25?C on Salt Creek. Median specific-conductance values among sites in the Cheyenne River drainage basin ranged from 1,850 ?S/cm at 25?C on Black Thunder Creek to 4,680 ?S/cm at 25?C on the Cheyenne River. The entire Cheyenne River drainage basin is in the plains, which have low precipitation, soluble geologic materials, and relatively low gradients that produce slow stream velocities and long contact times. Median specific-conductance values among sites in the Belle Fourche River drainage basin ranged from 1,740 ?S/cm at 25?C on Caballo Creek to 2,800 ?S/cm at 25?C on Donkey Creek. Water in the study area ranged from a magnesium-calcium-bicarbonate type for some sites in the Tongue River drainage basin to a sodium-sulfate type at many sites in the Powder, Cheyenne, and Belle Fourche River drainage basins. Little Goose Creek, Goose Creek, and the Tongue River in the Tongue River drainage basin, and Clear Creek in the Powder River drainage basin, which have headwaters in the Bighorn Mountains, consistently had the smallest median dissolved-sodium concentrations, sodium-adsorption ratios, dissolved-sulfate concentrations, and dissolved-solids concentrations. Salt Creek, Wild Horse Creek, Little Powder River, and the Cheyenne River, which have headwat

Correlation between ion diffusional motion and ionic conductivity for different electrolytes based on ionic liquid.

PubMed

Kaur, Dilraj Preet; Yamada, K; Park, Jin-Soo; Sekhon, S S

2009-04-23

Room temperature ionic liquid 2,3-dimethyl-1-hexylimidazolium bis(trifluoromethane sulfonyl)imide (DMHxImTFSI) has been synthesized and used in the preparation of polymer gel electrolytes containing polymethylmethacrylate and propylene carbonate (PC). The onset of ion diffusional motion has been studied by (1)H and (19)F NMR spectroscopy and the results obtained for ionic liquid, liquid electrolytes, and polymer gel electrolytes have been correlated with the ionic conductivity results for these electrolytes in the 100-400 K temperature range. The temperature at which (1)H and (19)F NMR lines show motional narrowing and hence ion diffusional motion starts has been found to be closely related to the temperature at which a large increase in ionic conductivity has been observed for these electrolytes. Polymer gel electrolytes have high ionic conductivity over a wide range of temperatures. Thermogravimetric analysis/differential scanning calorimetry studies show that the ionic liquid (DMHxImTFSI) used in the present study is thermally stable up to 400 degrees C, whereas the addition of PC lowers the thermal stability of polymer gel electrolytes containing the ionic liquid. Different electrolytes have been observed to show high ionic conductivity in different range of temperatures, which can be helpful in the design of polymer gel electrolytes for specific applications.

Conducting polymer functionalized single-walled carbon nanotube based chemiresistive biosensor for the detection of human cardiac myoglobin

DOE Office of Scientific and Technical Information (OSTI.GOV)

Puri, Nidhi; Department of Physics, Faculty of Natural Sciences, Jamia Millia Islamia, New Delhi 110025; Niazi, Asad

2014-10-13

We report the fabrication of a single-walled carbon nanotube (SWNT) based ultrasensitive label-free chemiresistive biosensor for the detection of human cardiac biomarker, myoglobin (Ag-cMb). Poly(pyrrole-co-pyrrolepropylic acid) with pendant carboxyl groups was electrochemically deposited on electrophoretically aligned SWNT channel, as a conducting linker, for biomolecular immobilization of highly specific cardiac myoglobin antibody. The device was characterized by scanning electron microscopy, source-drain current-voltage (I-V), and charge-transfer characteristic studies. The device exhibited a linear response with a change in conductance in SWNT channel towards the target, Ag-cMb, over the concentration range of 1.0 to 1000 ng ml{sup −1} with a sensitivity of ∼118% per decademore » with high specificity.« less

Characterizing Extreme Environments for Army Testing

DTIC Science & Technology

2004-12-01

necessary to evaluate the plain, upland), well-developed and variable soil capability to conduct a specific test at a given location. profiles ( oxisols ...m) to medium (up to 20m) width streams, with nominal nominal velocities (ងm/s). Soils: Oxisols , ultisols, inceptisols, minimum depth in the range

Enhancing the spatial coverage of a regional high-quality hydraulic conductivity dataset with estimates made from domestic water-well specific-capacity tests

NASA Astrophysics Data System (ADS)

Priebe, Elizabeth H.; Neville, C. J.; Rudolph, D. L.

2018-03-01

The spatial coverage of hydraulic conductivity ( K) values for large-scale groundwater investigations is often poor because of the high costs associated with hydraulic testing and the large areas under investigation. Domestic water wells are ubiquitous and their well logs represent an untapped resource of information that includes mandatory specific-capacity tests, from which K can be estimated. These specific-capacity tests are routinely conducted at such low pumping rates that well losses are normally insignificant. In this study, a simple and practical approach to augmenting high-quality K values with reconnaissance-level K values from water-well specific-capacity tests is assessed. The integration of lesser quality K values from specific-capacity tests with a high-quality K data set is assessed through comparisons at two different scales: study-area-wide (a 600-km2 area in Ontario, Canada) and in a single geological formation within a portion of the broader study area (200 km2). Results of the comparisons demonstrate that reconnaissance-level K estimates from specific-capacity tests approximate the ranges and distributions of the high-quality K values. Sufficient detail about the physical basis and assumptions that are invoked in the development of the approach are presented here so that it can be applied with confidence by practitioners seeking to enhance their spatial coverage of K values with specific-capacity tests.

Sakai et al. is not an adequate demonstration of TFT effectiveness.

PubMed

Lohr, J M

2001-10-01

Sakai et al. (2001) report an uncontrolled case series of TFT treatments applied to a wide range of psychological complaints in a large health maintenance facility. They analyze verbal report measures of symptom severity and conclude that the specific treatment is effective for a wide range of psychological problems. A review of the theory and research on TFT efficacy indicates that the theoretical basis for the specific treatment is unfounded and that adequately controlled efficacy research has yet to be conducted. The authors' conclusions about effectiveness and applicability are not supported by either theory, prior research, or the findings of their clinical application. Copyright 2001 John Wiley & Sons, Inc.

Annual water-resources review, White Sands Missile Range, New Mexico, 1977; a hydrologic-data report

USGS Publications Warehouse

Cruz, R.R.

1978-01-01

Ground-water data were collected in 1977 at White Sands Missile Range in south-central New Mexico. Near the Post Headquarters water-level declines for the period 1968-77 declined about 20 feet. Total ground-water pumpage at White Sands Missile Range for 1977 was 2,146 acre-feet, 93 acre-feet more than in 1976. Wells at the Post Headquarters produced 2,112 acre-feet of the total volume. Specific conductance of ground water ranged from 277 to 2,410 micromhos per centimeter at 25 degrees Celsius for wells T-4 and T-14 respectively at Post Headquarters. (Woodard-USGS)

Effects of suspended sulfates on human health.

PubMed Central

French, J G

1975-01-01

Recent evidence from epidemiologic studies conducted in several areas of the United States shows an association of excess risk of asthmatic attacks with elevated levels of suspended sulfates within specific temperature ranges. These findings are disscussed in the context of experimental animal studies which tend to support these observations. PMID:1157797

Information-Seeking Behaviors of Education Literature User Populations

ERIC Educational Resources Information Center

Wright, Carol S.

2010-01-01

Background/Context: A thorough understanding of the information-seeking behaviors of specific disciplines, as well as distinct user groups within a discipline, is fundamental to the process of development of disciplinary informatics. Significant research has been conducted, largely by library and information science scholars across a range of…

Water quality of selected lakes in Mount Rainier National Park, Washington with respect to lake acidification

USGS Publications Warehouse

Turney, G.L.; Dion, N.P.; Sumioka, S.S.

1986-01-01

Thirteen lakes in Mount Rainier National Park were evaluated for general chemical characteristics, sensitivity to acidification by acidic precipitation, and degree of existing acidification. The lakes studies were Allen, one of the Chenuis group, Crescent , Crystal, Eleanor, Fan, one of the Golden group, Marsh, Mowich, Mystic, Shriner, and two unnamed lakes. The lakes were sampled in August 1983. Specific conductance values were generally 21 microsiemens/cm at 25 C or less, and dissolved solids concentrations were generally 20 mg/L or less. The major cations were calcium and sodium, and the major anion was bicarbonate. Alkalinity concentrations ranged from 2.1 to 9.0 mg/L in 12 of the lakes. Allen Lake was the exception, having an alkalinity concentration of 27 mg/L. The pH values for all of the lakes ranged from 5.8 to 6.5. In most of the lakes, vertical profiles of temperature, dissolved oxygen, pH, and specific conductance were relatively uniform. In the deeper lakes, temperature decreased with depth and dissolved-oxygen concentrations increased to about 20 feet, remained constant to 80 ft, then decreased with increasing depth. Exceptions to general water quality patterns were observed in three lakes. Allen Lake had a specific conductance value of 58 Microsiemens/cm. The lake of the Golden group was anaerobic at the bottom and had relatively high concentrations of dissolved organic carbon and dissolved metals, and a lower light transmission than the other lakes studied. One of the unnamed lakes had relatively high concentrations of phytoplankton and dissolved organic carbon and relatively low levels of light transmission. Comparisons of lake data to acid-sensitivity thresholds for specific conductance and alkalinity indicated that all of the lakes except Allen would be sensitive to acidic precipitation. The small sizes of the lakes, and their locations in basins of high precipitation and weathering-resistant rock types, enhance their sensitivity. None of the lakes in this study appeared to be presently acidified. (Lantz-PTT)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bauer, Stephen J.; Urquhart, Alexander

Reconsolidated crushed salt is being considered as a backfilling material placed upon nuclear waste within a salt repository environment. In-depth knowledge of thermal and mechanical properties of the crushed salt as it reconsolidates is critical to thermal/mechanical modeling of the reconsolidation process. An experimental study was completed to quantitatively evaluate the thermal conductivity of reconsolidated crushed salt as a function of porosity and temperature. The crushed salt for this study came from the Waste Isolation Pilot Plant (WIPP). In this work the thermal conductivity of crushed salt with porosity ranging from 1% to 40% was determined from room temperature upmore » to 300°C, using two different experimental methods. Thermal properties (including thermal conductivity, thermal diffusivity and specific heat) of single-crystal salt were determined for the same temperature range. The salt was observed to dewater during heating; weight loss from the dewatering was quantified. The thermal conductivity of reconsolidated crushed salt decreases with increasing porosity; conversely, thermal conductivity increases as the salt consolidates. The thermal conductivity of reconsolidated crushed salt for a given porosity decreases with increasing temperature. A simple mixture theory model is presented to predict and compare to the data developed in this study.« less

Assimilation of temperature and hydraulic gradients for quantifying the spatial variability of streambed hydraulics

NASA Astrophysics Data System (ADS)

Huang, Xiang; Andrews, Charles B.; Liu, Jie; Yao, Yingying; Liu, Chuankun; Tyler, Scott W.; Selker, John S.; Zheng, Chunmiao

2016-08-01

Understanding the spatial and temporal characteristics of water flux into or out of shallow aquifers is imperative for water resources management and eco-environmental conservation. In this study, the spatial variability in the vertical specific fluxes and hydraulic conductivities in a streambed were evaluated by integrating distributed temperature sensing (DTS) data and vertical hydraulic gradients into an ensemble Kalman filter (EnKF) and smoother (EnKS) and an empirical thermal-mixing model. The formulation of the EnKF/EnKS assimilation scheme is based on a discretized 1D advection-conduction equation of heat transfer in the streambed. We first systematically tested a synthetic case and performed quantitative and statistical analyses to evaluate the performance of the assimilation schemes. Then a real-world case was evaluated to calculate assimilated specific flux. An initial estimate of the spatial distributions of the vertical hydraulic gradients was obtained from an empirical thermal-mixing model under steady-state conditions using a constant vertical hydraulic conductivity. Then, this initial estimate was updated by repeatedly dividing the assimilated specific flux by estimates of the vertical hydraulic gradients to obtain a refined spatial distribution of vertical hydraulic gradients and vertical hydraulic conductivities. Our results indicate that optimal parameters can be derived with fewer iterations but greater simulation effort using the EnKS compared with the EnKF. For the field application in a stream segment of the Heihe River Basin in northwest China, the average vertical hydraulic conductivities in the streambed varied over three orders of magnitude (5 × 10-1 to 5 × 102 m/d). The specific fluxes ranged from near zero (qz < ±0.05 m/d) to ±1.0 m/d, while the vertical hydraulic gradients were within the range of -0.2 to 0.15 m/m. The highest and most variable fluxes occurred adjacent to a debris-dam and bridge pier. This phenomenon is very likely the result of heterogeneous streambed hydraulic characteristics in these areas. Our results have significant implications for hyporheic micro-habitats, fish spawning and other wildlife incubation, regional flow and hyporheic solute transport models in the Heihe River Basin, as well as in other similar hydrologic settings.

Investigation of dioxin concentrations in the lower Roanoke River basin, North Carolina, February 26-March 7, 2001

USGS Publications Warehouse

Miller, K.F.; Walters, D.A.

2001-01-01

Dioxin is a toxic chemical that, when present in the environment, can cause cancer and birth defects in humans. Dioxin is of particular concern because concentrations of dioxin that were released into the environment many years ago remain a contributing factor to current exposure. Dioxin exposure often occurs in surface-water systems downstream from contaminated sites and is detrimental to aquatic life. For these reasons and because the U.S. Geological Survey has expertise in conducting high-volume dioxin sampling, the U.S. Environmental Protection Agency and the State of North Carolina asked the U.S. Geological Survey to collect water samples in the lower Roanoke River to be analyzed for the presence of dioxin. Water quality of the lower Roanoke River Basin in North Carolina was assessed at eight sites during February 26-March 7, 2001. Water- quality samples were collected for analysis of suspended-sediment and dioxin concentrations; high-volume (750-liter) water samples were collected for dioxin analysis. Discharge measurements were made at or near the high-volume sampling sites. Suspended-sediment sampling and water-quality measurements of specific conductance, pH, water temperature, and dissolved-oxygen concentrations made at each sampling site included multidepth measurements at two cross-section transects and hourly measurements at the point of high-volume sampling. Multidepth measurements were made near the surface, mid-depth, and near the bottom of the water column. These values were averaged for each cross section. During the sampling period, all sites sampled had dioxin concentrations above detection limits (1 part per quintillion) for both suspended and dissolved dioxin. Suspended dioxin ranged from 5.1 to 900 femtograms per liter, and dissolved dioxin values ranged from 0.31 to 41 femtograms per liter. Suspended-sediment concentrations ranged from 1.1 to 14 milligrams per liter. Specific conductance values ranges from 111 to 340 microsiemens per centimeter at 25 degrees Celsius. The range of pH values at the sampling sites was from 6.6 to 7.7. Water temperatures ranged from 8.9 to 13 degrees Celsius. Dissolved-oxygen concentrations ranged from 7.3 to 10.9 milligrams per liter.

Water-quality characteristics, including sodium-adsorption ratios, for four sites in the Powder River drainage basin, Wyoming and Montana, water years 2001-2004

USGS Publications Warehouse

Clark, Melanie L.; Mason, Jon P.

2006-01-01

The U.S. Geological Survey, in cooperation with the Wyoming Department of Environmental Quality, monitors streams throughout the Powder River structural basin in Wyoming and parts of Montana for potential effects of coalbed natural gas development. Specific conductance and sodium-adsorption ratios may be larger in coalbed waters than in stream waters that may receive the discharge waters. Therefore, continuous water-quality instruments for specific conductance were installed and discrete water-quality samples were collected to characterize water quality during water years 2001-2004 at four sites in the Powder River drainage basin: Powder River at Sussex, Wyoming; Crazy Woman Creek near Arvada, Wyoming; Clear Creek near Arvada, Wyoming; and Powder River at Moorhead, Montana. During water years 2001-2004, the median specific conductance of 2,270 microsiemens per centimeter at 25 degrees Celsius (?S/cm) in discrete samples from the Powder River at Sussex, Wyoming, was larger than the median specific conductance of 1,930 ?S/cm in discrete samples collected downstream from the Powder River at Moorhead, Montana. The median specific conductance was smallest in discrete samples from Clear Creek (1,180 ?S/cm), which has a dilution effect on the specific conductance for the Powder River at Moorhead, Montana. The daily mean specific conductance from continuous water-quality instruments during the irrigation season showed the same spatial pattern as specific conductance values for the discrete samples. Dissolved sodium, sodium-adsorption ratios, and dissolved solids generally showed the same spatial pattern as specific conductance. The largest median sodium concentration (274 milligrams per liter) and the largest range of sodium-adsorption ratios (3.7 to 21) were measured in discrete samples from the Powder River at Sussex, Wyoming. Median concentrations of sodium and sodium-adsorption ratios were substantially smaller in Crazy Woman Creek and Clear Creek, which tend to decrease sodium concentrations and sodium-adsorption ratios at the Powder River at Moorhead, Montana. Dissolved-solids concentrations in discrete samples were closely correlated with specific conductance values; Pearson's correlation coefficients were 0.98 or greater for all four sites. Regression equations for discrete values of specific conductance and sodium-adsorption ratios were statistically significant (p-values <0.001) at all four sites. The strongest relation (R2=0.92) was at the Powder River at Sussex, Wyoming. Relations on Crazy Woman Creek (R2=0.91) and Clear Creek (R2=0.83) also were strong. The relation between specific conductance and sodium-adsorption ratios was weakest (R2=0.65) at the Powder River at Moorhead, Montana; however, the relation was still significant. These data indicate that values of specific conductance are useful for estimating sodium-adsorption ratios. A regression model called LOADEST was used to estimate dissolved-solids loads for the four sites. The average daily mean dissolved-solids loads varied among the sites during water year 2004. The largest average daily mean dissolved-solids load was calculated for the Powder River at Moorhead, Montana. Although the smallest concentrations of dissolved solids were in samples from Clear Creek, the smallest average daily mean dissolved-solids load was calculated for Crazy Woman Creek. The largest loads occurred during spring runoff, and the smallest loads occurred in late summer, when streamflows typically were smallest. Dissolved-solids loads may be smaller than average during water years 2001-2004 because of smaller than average streamflow as a result of drought conditions.

Effective conductivity and permittivity of unsaturated porous materials in the frequency range 1 mHz–1GHz

PubMed Central

Revil, A

2013-01-01

A model combining low-frequency complex conductivity and high-frequency permittivity is developed in the frequency range from 1 mHz to 1 GHz. The low-frequency conductivity depends on pore water and surface conductivities. Surface conductivity is controlled by the electrical diffuse layer, the outer component of the electrical double layer coating the surface of the minerals. The frequency dependence of the effective quadrature conductivity shows three domains. Below a critical frequency fp, which depends on the dynamic pore throat size Λ, the quadrature conductivity is frequency dependent. Between fp and a second critical frequency fd, the quadrature conductivity is generally well described by a plateau when clay minerals are present in the material. Clay-free porous materials with a narrow grain size distribution are described by a Cole-Cole model. The characteristic frequency fd controls the transition between double layer polarization and the effect of the high-frequency permittivity of the material. The Maxwell-Wagner polarization is found to be relatively negligible. For a broad range of frequencies below 1 MHz, the effective permittivity exhibits a strong dependence with the cation exchange capacity and the specific surface area. At high frequency, above the critical frequency fd, the effective permittivity reaches a high-frequency asymptotic limit that is controlled by the two Archie's exponents m and n like the low-frequency electrical conductivity. The unified model is compared with various data sets from the literature and is able to explain fairly well a broad number of observations with a very small number of textural and electrochemical parameters. It could be therefore used to interpret induced polarization, induction-based electromagnetic methods, and ground penetrating radar data to characterize the vadose zone. PMID:23576823

Spatial distribution and vertical migration of (137)Cs in soils of Belgrade (Serbia) 25 years after the Chernobyl accident.

PubMed

Petrović, Jelena; Ćujić, Mirjana; Đorđević, Milan; Dragović, Ranko; Gajić, Boško; Miljanić, Šćepan; Dragović, Snežana

2013-06-01

In this study, the specific activity of (137)Cs was determined by gamma-ray spectrometry in 72 surface soil samples and 11 soil profiles collected from the territory of Belgrade 25 years after the Chernobyl accident. Based on the data obtained the external effective gamma dose rates due to (137)Cs were assessed and geographically mapped. The influence of pedogenic factors (pH, specific electrical conductivity, cation exchange capacity, organic matter content, soil particle size and carbonate content) on the spatial and vertical distribution of (137)Cs in soil was estimated through Pearson correlations. The specific activity of (137)Cs in surface soil samples ranged from 1.00 to 180 Bq kg(-1), with a mean value of 29.9 Bq kg(-1), while in soil profiles they ranged from 0.90 to 58.0 Bq kg(-1), with a mean value of 15.3 Bq kg(-1). The mean external effective gamma dose at 1 m above the ground due to (137)Cs in the soil was calculated to be 1.96 nSv h(-1). Geographic mapping of the external effective gamma dose rates originating from (137)Cs revealed much higher dose rates in southern parts of Belgrade city and around the confluence of the Sava and Danube. Negative Pearson correlation coefficients were found between pH, cation exchange capacity and (137)Cs specific activity in surface soil. There were positive correlations between organic matter and (137)Cs specific activity in surface soil; and between specific electrical conductivity, organic matter, silt content and (137)Cs specific activity in soil profiles.

Pacemaker Dependency after Cardiac Surgery: A Systematic Review of Current Evidence.

PubMed

Steyers, Curtis M; Khera, Rohan; Bhave, Prashant

2015-01-01

Severe postoperative conduction disturbances requiring permanent pacemaker implantation frequently occur following cardiac surgery. Little is known about the long-term pacing requirements and risk factors for pacemaker dependency in this population. We performed a systematic review of the literature addressing rates and predictors of pacemaker dependency in patients requiring permanent pacemaker implantation after cardiac surgery. Using a comprehensive search of the Medline, Web of Science and EMBASE databases, studies were selected for review based on predetermined inclusion and exclusion criteria. A total of 8 studies addressing the endpoint of pacemaker-dependency were identified, while 3 studies were found that addressed the recovery of atrioventricular (AV) conduction endpoint. There were 10 unique studies with a total of 780 patients. Mean follow-up ranged from 6-72 months. Pacemaker dependency rates ranged from 32%-91% and recovery of AV conduction ranged from 16%-42%. There was significant heterogeneity with respect to the definition of pacemaker dependency. Several patient and procedure-specific variables were found to be independently associated with pacemaker dependency, but these were not consistent between studies. Pacemaker dependency following cardiac surgery occurs with variable frequency. While individual studies have identified various perioperative risk factors for pacemaker dependency and non-resolution of AV conduction disease, results have been inconsistent. Well-conducted studies using a uniform definition of pacemaker dependency might identify patients who will benefit most from early permanent pacemaker implantation after cardiac surgery.

Macroalgae in a spring stream in Shanxi Province: composition and relation to physical and chemical variables

NASA Astrophysics Data System (ADS)

Hu, Bianfang; Xie, Shulian

2007-07-01

Fourteen stream segments were investigated throughout the Xin’an Spring in Shanxi Province, China in 2004. The variation ranges in stream size, current velocity, discharge, dissolved oxygen, and specific conductance were large. Twenty-two macroalgae species were found in the stream. Major divisions in terms of species numbers were Chlorophyta (59.1%), Cyanophyta (22.8%), Xanthophyta (9.1%), Rhodophyta (4.5%) and Charophyta (4.5%). The most widespread species, Cladophora rivularis (50.0%), also Oedogonium sp. (42.9%) and Spirogyra sp. (42.9%) were well represented throughout the stream, whereas another 10 species were found in only one sampling site. Total percentage cover varied from <1% to 90%. Red algae Batrachospermum acuatum and the charophytes Chara vulgaris have the highest percentage cover. Among the parameters analyzed, the stream width, specific conductance and dissolved oxygen were the ones that more closely related to the species number and percentage cover of macroalgal communities. The species number of each site was negatively correlated with dissolved oxygen content. The total percentage cover of the macroalgae was negatively correlated with the stream width and the specific conductance.

Geochemistry of altered and mineralized rocks from the Morey and Fandango Wilderness Study Areas, northern Hot Creek Range, Nye County, Nevada

USGS Publications Warehouse

Nash, J.T.; John, D.A.; Malcolm, M.J.; Briggs, P.H.; Crock, J.G.

1986-01-01

The U.S. Geological Survey and the St. Johns River Water Management District are investigating the hydrogeology of the Floridan aquifer system. An essential element of this investigation is the design and construction of a monitor well network in the lower saline water-bearing zone which occurs at about 2,000 ft below land surface. During 1985, a well near Ponte Vedra in northeast St. Johns County was completed into the lower saline water-bearing zone at a depth of 1,980 to 2,035 ft below land surface. This well and other wells drilled under this or other programs will be used to monitor water levels and water chemistry of the lower saline zone. Chloride concentrations in water above the lower saline zone ranged from 14 to 270 mg/L and specific conductance ranged from 450 to 1,440 micromhos/cm c. In the lower zone, chloride concentrations were as much as 16,210 mg/L and specific conductance as much as 46,000 micromhos per centimeter. Aquifer head and artesian flow from the well generally increased with depth. Water temperatures also increased from 23 C in the upper part of the aquifer to more than 28 C in the lower saline zone. (USGS)

Data and material of the Safe-Range-Inventory: An assistance tool helping to improve the charging infrastructure for electric vehicles.

PubMed

Carbon, Claus-Christian; Gebauer, Fabian

2017-10-01

The Safe-Range-Inventory (SRI) was constructed in order to help public authorities to improve the charging infrastructures for electric vehicles [1; 10.1016/j.trf.2017.04.011]. Specifically, the impact of fast (vs slow) charging stations on people's range anxiety was examined. Ninety-seven electric vehicle users from Germany (81 male; M age =46.3 years, SD =12.1) were recruited to participate in the experimental design. Statistical analyses were conducted using ANOVA for repeated measures to test for interaction effects of available charging stations and remaining range with the dependent variable range anxiety . The full data set is publicly available via https://osf.io/bveyw/ (Carbon and Gebauer, 2017) [2].

T-COMP—A suite of programs for extracting transmissivity from MODFLOW models

USGS Publications Warehouse

Halford, Keith J.

2016-02-12

Simulated transmissivities are constrained poorly by assigning permissible ranges of hydraulic conductivities from aquifer-test results to hydrogeologic units in groundwater-flow models. These wide ranges are derived from interpretations of many aquifer tests that are categorized by hydrogeologic unit. Uncertainty is added where contributing thicknesses differ between field estimates and numerical models. Wide ranges of hydraulic conductivities and discordant thicknesses result in simulated transmissivities that frequently are much greater than aquifer-test results. Multiple orders of magnitude differences frequently occur between simulated and observed transmissivities where observed transmissivities are less than 1,000 feet squared per day.Transmissivity observations from individual aquifer tests can constrain model calibration as head and flow observations do. This approach is superior to diluting aquifer-test results into generalized ranges of hydraulic conductivities. Observed and simulated transmissivities can be compared directly with T-COMP, a suite of three FORTRAN programs. Transmissivity observations require that simulated hydraulic conductivities and thicknesses in the volume investigated by an aquifer test be extracted and integrated into a simulated transmissivity. Transmissivities of MODFLOW model cells are sampled within the volume affected by an aquifer test as defined by a well-specific, radial-flow model of each aquifer test. Sampled transmissivities of model cells are averaged within a layer and summed across layers. Accuracy of the approach was tested with hypothetical, multiple-aquifer models where specified transmissivities ranged between 250 and 20,000 feet squared per day. More than 90 percent of simulated transmissivities were within a factor of 2 of specified transmissivities.

Loci of Difficulty in Learning to Program. Technical Report 86-6.

ERIC Educational Resources Information Center

Perkins, David; And Others

To learn more about the specific nature of the teaching and learning problems involved, researchers conducted a clinical study of 20 high school students enrolled a BASIC course. Investigators presented each student with a sequence of eight programming problems, ranging from easy to difficult. They asked questions to track student thinking and…

Development of Attentional and Oculomotor Control

ERIC Educational Resources Information Center

Kramer, Arthur F.; Gonzalez de Sather, Jessica C. M.; Cassavaugh, Nicholas D.

2005-01-01

The present study was conducted to examine the development of attentional and oculomotor control. More specifically, the authors were interested in the development of the ability to inhibit an incorrect but prepotent response to a salient distractor. Participants, who ranged in age from 8 to 25 years, performed 3 different eye movement tasks: a…

A unified metabolism for Mars: A new approach developed from research on extraterrestrial life detection by enzymatically induced exchange of O 18

NASA Technical Reports Server (NTRS)

1972-01-01

A general graded life detection approach ranging from environmental and in situ observations to specific metabolic experiments on Mars is reported. A zero dead volume leak and computer mediated data acquisition system is also discussed. Soil analyses were also conducted.

Thermophysical properties of enzyme clarified Lime (Citrus aurantifolia L) juice at different moisture contents.

PubMed

Manjunatha, S S; Raju, P S; Bawa, A S

2014-11-01

Thermophysical properties of enzyme clarified lime (Citrus aurantifolia L.) juice were evaluated at different moisture contents ranging from 30.37 % to 89.30 % (wet basis) corresponding to a water activity range of 0.835 to 0.979. The thermophysical properties evaluated were density, Newtonian viscosity, thermal conductivity, specific heat and thermal diffusivity. The investigation showed that density and Newtonian viscosity of enzyme clarified lime juice decreased significantly (p < 0.05) with increase in moisture content and water activity, whereas thermal conductivity and specific heat increased significantly (p < 0.05) with increase in moisture content and water activity and the thermal diffusivity increased marginally. Empirical mathematical models were established relating to thermophysical properties of enzyme clarified lime juice with moisture content/water activity employing regression analysis by the method of least square approximation. Results indicated the existence of strong correlation between thermophysical properties and moisture content/water activity of enzyme clarified lime juice, a significant (p < 0.0001) negative correlation between physical and thermal properties was observed.

Environmental geochemical study of Red Mountain--an undisturbed volcanogenic massive sulfide deposit in the Bonnifield District, Alaska range, east-central Alaska: Chapter I in Recent U.S. Geological Survey studies in the Tintina Gold Province, Alaska, United States, and Yukon, Canada--results of a 5-year project

USGS Publications Warehouse

Eppinger, Robert G.; Briggs, Paul H.; Dusel-Bacon, Cynthia; Giles, Stuart A.; Gough, Larry P.; Hammarstrom, Jane M.; Hubbard, Bernard E.

2007-01-01

Water samples with the lowest pH values, highest specific conductances, and highest major- and trace-element concentrations are from springs and streams within the quartz-sericite-pyrite alteration zone. Aluminum, As, Cd, Co, Cu, Fe, Mn, Ni, Pb, Y, and particularly Zn and the REEs are all found in high concentrations, ranging across four orders of magnitude. Waters collected upstream from the alteration zone have near-neutral pH values, lower specific conductances, lower metal concentrations, and measurable alkalinities. Water samples collected downstream of the alteration zone have pH values and metal concentrations intermediate between these two extremes. Stream sediments are anomalous in Zn, Pb, S, Fe, Cu, As, Co, Sb, and Cd relative to local and regional background abundances. Red Mountain Creek and its tributaries do not support, and probably never have supported, significant megascopic faunal aquatic life.

Partially Turboelectric Aircraft Drive Key Performance Parameters

NASA Technical Reports Server (NTRS)

Jansen, Ralph H.; Duffy, Kirsten P.; Brown, Gerald V.

2017-01-01

The purpose of this paper is to propose electric drive specific power, electric drive efficiency, and electrical propulsion fraction as the key performance parameters for a partially turboelectric aircraft power system and to investigate their impact on the overall aircraft performance. Breguet range equations for a base conventional turbofan aircraft and a partially turboelectric aircraft are found. The benefits and costs that may result from the partially turboelectric system are enumerated. A break even analysis is conducted to find the minimum allowable electric drive specific power and efficiency, for a given electrical propulsion fraction, that can preserve the range, fuel weight, operating empty weight, and payload weight of the conventional aircraft. Current and future power system performance is compared to the required performance to determine the potential benefit.

Response of benthic algae to environmental gradients in an agriculturally dominated landscape

USGS Publications Warehouse

Munn, M.D.; Black, R.W.; Gruber, S.J.

2002-01-01

Benthic algal communities were assessed in an agriculturally dominated landscape in the Central Columbia Plateau, Washington, to determine which environmental variables best explained species distributions, and whether algae species optima models were useful in predicting specific water-quality parameters. Land uses in the study area included forest, range, urban, and agriculture. Most of the streams in this region can be characterized as open-channel systems influenced by intensive dryland (nonirrigated) and irrigated agriculture. Algal communities in forested streams were dominated by blue-green algae, with communities in urban and range streams dominated by diatoms. The predominance of either blue-greens or diatoms in agricultural streams varied greatly depending on the specific site. Canonical correspondence analysis (CCA) indicated a strong gradient effect of several key environmental variables on benthic algal community composition. Conductivity and % agriculture were the dominant explanatory variables when all sites (n = 24) were included in the CCA; water velocity replaced conductivity when the CCA included only agricultural and urban sites. Other significant explanatory variables included dissolved inorganic nitrogen (DIN), orthophosphate (OP), discharge, and precipitation. Regression and calibration models accurately predicted conductivity based on benthic algal communities, with OP having slightly lower predictability. The model for DIN was poor, and therefore may be less useful in this system. Thirty-four algal taxa were identified as potential indicators of conductivity and nutrient conditions, with most indicators being diatoms except for the blue-greens Anabaenasp. and Lyngbya sp.

Geochemical controls of elevated arsenic concentrations in groundwater, Ester Dome, Fairbanks district, Alaska

USGS Publications Warehouse

Verplanck, P.L.; Mueller, S.H.; Goldfarb, R.J.; Nordstrom, D. Kirk; Youcha, E.K.

2008-01-01

Ester Dome, an upland area near Fairbanks, Alaska, was chosen for a detailed hydrogeochemical study because of the previously reported elevated arsenic in groundwater, and the presence of a large set of wells amenable to detailed sampling. Ester Dome lies within the Fairbanks mining district, where gold-bearing quartz veins, typically containing 2-3??vol.% sulfide minerals (arsenopyrite, stibnite, and pyrite), have been mined both underground and in open cuts. Gold-bearing veins on Ester Dome occur in shear zones and the sulfide minerals in these veins have been crushed to fine-grained material by syn- or post-mineralization movement. Groundwater at Ester Dome is circumneutral, Ca-HCO3 to Ca-SO4 type, and ranges from dilute (specific conductance of 48????S/cm) to more concentrated (specific conductance as high as 2070????S/cm). In general, solute concentrations increase down hydrologic gradient. Redox species indicate that the groundwaters range from oxic to sub-oxic (low dissolved oxygen, Fe(III) reduction, no SO4 reduction). Waters with the highest Fe concentrations, as high as 10.7??mg/L, are the most anoxic. Dissolved As concentrations range from < 1 to 1160????g/L, with a median value of 146????g/L. Arsenic concentrations are not correlated with specific conductance or Fe concentrations, suggesting that neither groundwater residence time, nor reductive dissolution of iron oxyhydroxides, control the arsenic chemistry. Furthermore, As concentrations do not covary with other constituents that form anions and oxyanions in solution (e.g., HCO3, Mo, F, or U) such that desorption of arsenic from clays or oxides also does not control arsenic mobility. Oxidation of arsenopyrite and dissolution of scorodite, in the near-surface environment appears to be the primary control of dissolved As in this upland area. More specifically, the elevated As concentrations are spatially associated with sulfidized shear zones and localities of gold-bearing quartz veins. Consistent with this interpretation, elevated dissolved Sb concentrations (as high as 59????g/L), also correlated with occurrences of hypogene sulfide minerals, were measured in samples with high dissolved As concentrations.

Thermophysical properties of Apollo 14 fines

NASA Technical Reports Server (NTRS)

Cremers, C. J.

1974-01-01

The vacuum thermal conductivity of lunar fines sample 14163 was measured for the approximate temperature range of 100 to 400 K. Sample densities of 1500 kg/cu m and 1800 kg/cu m were used. The temperature dependence of the conductivity was found to be well represented by the relation k = A + BT-cubed, which is predicted by elementary theory. The coefficients A and B were obtained by least-squares analysis of the data. The thermal diffusivity was calculated for the various densities using specific heat data from the literature along with the measured conductivities. The results are compared with those obtained for Apollo 11, Apollo 12, and terrestrial basalt samples.

Experimental determination of single-crystal halite thermal conductivity, diffusivity and specific heat from -75°C to 300°C

DOE PAGES

Urquhart, Alexander; Bauer, Stephen

2015-05-19

The thermal properties of halite have broad practical importance, from design and long-term modeling of nuclear waste repositories to analysis and performance assessment of underground natural gas, petroleum and air storage facilities. Using a computer-controlled transient plane source method, single-crystal halite thermal conductivity, thermal diffusivity and specific heat were measured from -75°C to 300°C. These measurements reproduce historical high-temperature experiments and extend the lower temperature extreme into cryogenic conditions. Measurements were taken in 25-degree increments from -75°C to 300°C. Over this temperature range, thermal conductivity decreases by a factor of 3.7, from 9.975 to 2.699 W/mK , and thermal diffusivitymore » decreases by a factor of 3.6, from 5.032 to 1.396 mm²/s. Specific heat does not appear to be temperature dependent, remaining near 2.0 MJ/m³K at all temperatures. This work is intended to develop and expand the existing dataset of halite thermal properties, which are of particular value in defining the parameters of salt storage thermophysical models. The work was motivated by a need for thermal conductivity values in a mixture theory model used to determine bulk thermal conductivity of reconsolidating crushed salt.« less

Does water chemistry limit the distribution of New Zealand mud snails in Redwood National Park?

USGS Publications Warehouse

Vazquez, Ryan; Ward, Darren M.; Sepulveda, Adam

2016-01-01

New Zealand mud snails (NZMS) are exotic mollusks present in many waterways of the western United States. In 2009, NZMS were detected in Redwood Creek in Redwood National Park, CA. Although NZMS are noted for their ability to rapidly increase in abundance and colonize new areas, after more than 5 years in Redwood Creek, their distribution remains limited to a ca. 300 m reach. Recent literature suggests that low specific conductivity and environmental calcium can limit NZMS distribution. We conducted laboratory experiments, exposing NZMS collected from Redwood Creek to both natural waters and artificial treatment solutions, to determine if low conductivity and calcium concentration limit the distribution of NZMS in Redwood National Park. For natural water exposures, we held NZMS in water from their source location (conductivity 135 μS/cm, calcium 13 mg/L) or water from four other locations in the Redwood Creek watershed encompassing a range of conductivity (77–158 μS/cm) and calcium concentration (<5–13 mg/L). For exposures in treatment solutions, we manipulated both conductivity (range 20–200 μS/cm) and calcium concentration (range <5–17.5 mg/L) in a factorial design. Response variables measured included mortality and reproductive output. Adult NZMS survived for long periods (>4 months) in the lowest conductivity waters from Redwood Creek and all but the lowest-conductivity treatment solutions, regardless of calcium concentration. However, reproductive output was very low in all natural waters and all low-calcium treatment solutions. Our results suggest that water chemistry may inhibit the spread of NZMS in Redwood National Park by reducing their reproductive output.

Developing a New Thermophysical Model for Lunar Regolith Soil at Low Temperatures

NASA Astrophysics Data System (ADS)

Woods-Robinson, R.; Siegler, M. A.; Paige, D. A.

2016-12-01

The thermophysical properties of the lunar regolith soil have been thoroughly investigated within the temperature range of 100 - 400 K. Extensive laboratory measurements of temperature-dependent thermal conductivity and specific heat have been performed on lunar samples collected from the Apollo and Luna missions. However, recent thermal emission measurements from the Lunar Reconnaissance Orbiter Diviner Lunar Radiometer Experiment have revealed temperatures near the poles as low 20 K, far below where existing thermophysical models begin to break down. In the absence of comprehensive laboratory measurements of lunar soil thermal properties at these low temperatures (20 - 100 K), we investigate solid state theory and lunar simulant materials to derive a physically-based theoretical model of specific heat and thermal conductivity in lunar soils in the full range 20 - 400 K. The primary distinctions between this model and its predecessors are: The focus on soil bulk density as a master variable The temperature dependence of the solid conduction component of thermal conductivity at low temperatures, and The concept that the composition and modal petrology of grains - both amorphous and crystalline components - could significantly influence thermal properties of the bulk soil. The simplest version of this model, which assumes that the soil behaves predominantly as a homogeneous particulate material composed of amorphous grains, shows that at low temperatures (20 - 100 K), specific heat is likely higher than expected from current models ( 0.027 J/gK at 20 K) and that thermal conductivity is almost an order of magnitude lower than has generally been assumed in the literature.Any higher-order approximation is difficult at this stage; the thermal conductivity at low temperature could vary drastically depending on the constituent grain materials, their degree of crystallinity, and contributions from phonon scattering modes, among other factors. We use a one-dimensional thermal model to illustrate the effects of our model on diurnal surface temperature variations in permanently shadowed regions on the moon. We aim to lay the theoretical foundation for a new approach to model thermal properties of regolith materials, and to justify the importance of new laboratory measurements of lunar soil below 100 K.

Geohydrology and potential hydrologic effects of underground coal mining in the Rapid Creek Basin, Mesa County, Colorado

USGS Publications Warehouse

Brooks, Tom

1986-01-01

The U.S. Bureau of Land Management may lease additional coal tracts in the Rapid Creek basin, Colorado. Springs in this basin are used as a water supply for the town of Palisade. The geohydrology of the basin is described and the potential hydrologic effects of underground coal mining in the basin summarized. Geologic formations in the basin consists of Cretaceous sandstone and shale, Tertiary sandstone, shale, and basalt, and unconsolidated deposits of Quaternary age. Some sandstone and coal beds are permeable, although bedrock in the basin typically is a confining bed. Unconsolidated deposits contain aquifers that are the source of spring discharge. Stream discharge was measured on Rapid and Cottonwood Creeks, and inventories were made of 7 reservoirs, 25 springs, and 12 wells. Specific conductance of streams ranged from 320 to 1,050 microsiemens/cm at 25C; pH ranged from 7.8 to 8.6. Specific conductance of springs ranged from 95 to 1,050 microsiemens/cm at 25C; pH ranged from 6.8 to 8.3. Discharge from the basin includes about 18,800 acre-ft/yr as evapotranspiration, 1,300 acre-ft/yr as springflow, 1,280 acre-ft/yr as streamflow, and negligible groundwater flow in bedrock. With appropriate mining methods, underground mining would not decrease flow in basin streams or from springs. The potential effects of mining-caused subsidence might include water-pipeline damage and temporary dewatering of bedrock adjacent to coal mining. (Author 's abstract)

Experimental measurements and evaluation of the expanded water repellent perlite used for the cargo containment system of LNG carrier

NASA Astrophysics Data System (ADS)

Li, Manfeng; Ju, Yonglin

2017-10-01

To minimize the water absorption and to improve the thermal insulated properties of the insulation materials used for the cargo containment systems (CCSs) of LNG carrier, a kind of expanded water-repellent perlite has been developed by coating hydrophobic membrane onto the outer surface of the expanded perlite to change its physical and chemical characteristics. Considering the CCSs operated in a wide temperature range from environmental temperature to cryogenic temperature, the thermal analysis has been conducted to quantitatively determine the thermal insulted properties of the insulation materials. Furthermore, a double-sided guarded hot plate apparatus (GHP) is specifically designed and fabricated for the measurement of the thermal conductivities of the insulation specimens operated down to liquid nitrogen temperature. The breakage ratio associated with the water absorption and the thermal conductivity of the expanded water-repellent perlite is firstly proposed, and then a series of experiments are carried out to determine the thermal conductivity of the expanded water-repellent perlite ranging from room temperature to cryogenic temperature based on the different breakage ratios.

Annual water-resources review, White Sands Missile Range, New Mexico

USGS Publications Warehouse

Cruz, R.R.

1983-01-01

Ground-water data were collected in 1982 at White Sands Missile Range in south-central New Mexico. Depth-to-water measurements in the Post Headquarters supply wells continued to show seasonal declines. Test wells east of the Headquarters well field continue to show long-term declines as well as seasonal fluctuations. The total amount of water pumped from White Sands Missile Range supply wells was 66,226,600 gallons more in 1982 than in 1981. The difference in the specific-conductance values of the water samples collected from the Post Headquarters supply wells in the winter and summer increased in 1982. (USGS)

Nuclear Resonance Fluorescence Response of U-235

NASA Astrophysics Data System (ADS)

Warren, Glen

2008-05-01

Nuclear resonance fluorescence (NRF) is a physical process that provides an isotopic-specific signature that could be used for the identification and characterization of materials. The technique involves the detection of prompt discrete-energy photons emitted from a sample, which is exposed to photons in the MeV energy range. Potential applications of the technique range from detection of high explosives to characterization of special nuclear materials. Pacific Northwest National Laboratory and Passport Systems have collaboratively conducted a set of measurements to search for an NRF response of U-235 in the 1.5 to 9 MeV energy range. Results from these measurements will be presented.

A preliminary assessment of the impact of 2-D exhaust-nozzle geometry on the cruise range of a hypersonic aircraft with top-mounted ramjet propulsion

NASA Technical Reports Server (NTRS)

Vahl, W. A.; Weidner, J. P.

1980-01-01

A theoretical study of full length and shortened, two dimensional, isentropic, exhaust nozzles integrated with top mounted ramjet propulsion nacelles were conducted. Both symmetric and asymmetric contoured nozzles with a range of angular orientations were considered. Performance comparisons to determine optimum installations for a representative hypersonic vehicle at Mach 5 cruise conditions are presented on the basis of cruise range, propulsive specific impulse, inlet area requirements, and overall lift drag ratio. The effect of approximating the nozzle internal contours with planar surfaces and the determination of viscous and frozen flow effects are also presented.

MIUS integration and subsystems test program

NASA Technical Reports Server (NTRS)

Beckham, W. S., Jr.; Shows, G. C.; Redding, T. E.; Wadle, R. C.; Keough, M. B.; Poradek, J. C.

1976-01-01

The MIUS Integration and Subsystems Test (MIST) facility at the Lyndon B. Johnson Space Center was completed and ready in May 1974 for conducting specific tests in direct support of the Modular Integrated Utility System (MIUS). A series of subsystems and integrated tests was conducted since that time, culminating in a series of 24-hour dynamic tests to further demonstrate the capabilities of the MIUS Program concepts to meet typical utility load profiles for a residential area. Results of the MIST Program are presented which achieved demonstrated plant thermal efficiencies ranging from 57 to 65 percent.

Writing instruction in kindergarten: examining an emerging area of research for children with writing and reading difficulties.

PubMed

Edwards, Lana

2003-01-01

This review examines the literature on how to teach kindergarten children with reading and writing difficulties how to write. Specifically, research on handwriting instruction, spelling instruction, and composition writing is discussed. Due to the limited number of empirical studies on writing that included kindergarten students with diagnosed reading and writing difficulties, selected studies conducted with the full range of kindergarten children, as well as studies conducted in the early elementary grades, are presented to highlight future directions for research.

Increasing atmospheric [CO2] from glacial through future levels affects drought tolerance via impacts on leaves, xylem and their integrated function

PubMed Central

Medeiros, Juliana S.; Ward, Joy K.

2013-01-01

Summary Changes in atmospheric carbon dioxide concentration ([CO2]) affect plant carbon/water trade-offs, with implications for drought tolerance. Leaf-level studies often indicate that drought tolerance may increase with rising [CO2], but integrated leaf and xylem responses are not well understood in this respect. In addition, the influence of low [CO2] of the last glacial period on drought tolerance and xylem properties is not well understood.We investigated the interactive effects of a broad range of [CO2] and plant water potentials on leaf function, xylem structure and function and the integration of leaf and xylem function in Phaseolus vulgaris.Elevated [CO2] decreased vessel implosion strength, reduced conduit specific hydraulic conductance, and compromised leaf specific xylem hydraulic conductance under moderate drought. By contrast, at glacial [CO2], transpiration was maintained under moderate drought via greater conduit specific and leaf specific hydraulic conductance in association with increased vessel implosion strength.Our study involving the integration of leaf and xylem responses suggests that increasing [CO2] does not improve drought tolerance. We show that under glacial conditions changes in leaf and xylem properties could increase drought tolerance, while under future conditions greater productivity may only occur when higher water use can be accommodated. PMID:23668237

Size dependent polaronic conduction in hematite

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sharma, Monika; Banday, Azeem; Murugavel, Sevi

2016-05-23

Lithium Ion Batteries have been attracted as the major renewable energy source for all portable electronic devices because of its advantages like superior energy density, high theoretical capacity, high specific energy, stable cycling and less memory effects. Recently, α-Fe{sub 2}O{sub 3} has been considered as a potential anode material due to high specific capacity, low cost, high abundance and environmental benignity. We have synthesized α-Fe{sub 2}O{sub 3} with various sizes by using the ball milling and sol-gel procedure. Here, we report the dc conductivity measurement for the crystallite size ranging from 15 nm to 50 nm. It has been observedmore » that the enhancement in the polaronic conductivity nearly two orders in magnitude while reducing the crystallite size from bulk into nano scale level. The enhancement in the conductivity is due to the augmented to compressive strain developed in the material which leads to pronounced decrease in the hopping length of polarons. Thus, nanocrystaline α-Fe{sub 2}O{sub 3} may be a better alternative anode material for lithium ion batteries than earlier reported systems.« less

Chaparral Shrub Hydraulic Traits, Size, and Life History Types Relate to Species Mortality during California’s Historic Drought of 2014

PubMed Central

MacKinnon, Evan D.; Dario, Hannah L.; Jacobsen, Anna L.; Pratt, R. Brandon; Davis, Stephen D.

2016-01-01

Chaparral is the most abundant vegetation type in California and current climate change models predict more frequent and severe droughts that could impact plant community structure. Understanding the factors related to species-specific drought mortality is essential to predict such changes. We predicted that life history type, hydraulic traits, and plant size would be related to the ability of species to survive drought. We evaluated the impact of these factors in a mature chaparral stand during the drought of 2014, which has been reported as the most severe in California in the last 1,200 years. We measured tissue water potential, native xylem specific conductivity, leaf specific conductivity, percentage loss in conductivity, and chlorophyll fluorescence for 11 species in February 2014, which was exceptionally dry following protracted drought. Mortality among the 11 dominant species ranged from 0 to 93%. Total stand density was reduced 63.4% and relative dominance of species shifted after the drought. Mortality was negatively correlated with water potential, native xylem specific conductivity, and chlorophyll fluorescence, but not with percent loss in hydraulic conductivity and leaf specific conductivity. The model that best explained mortality included species and plant size as main factors and indicated that larger plants had greater survival for 2 of the species. In general, species with greater resistance to water-stress induced cavitation showed greater mortality levels. Despite adult resprouters typically being more vulnerable to cavitation, results suggest that their more extensive root systems enable them to better access soil moisture and avoid harmful levels of dehydration. These results are consistent with the hypothesis that short-term high intensity droughts have the strongest effect on mature plants of shallow-rooted dehydration tolerant species, whereas deep-rooted dehydration avoiding species fare better in the short-term. Severe droughts can drive changes in chaparral structure as a result of the differential mortality among species. PMID:27391489

Chaparral Shrub Hydraulic Traits, Size, and Life History Types Relate to Species Mortality during California's Historic Drought of 2014.

PubMed

Venturas, Martin D; MacKinnon, Evan D; Dario, Hannah L; Jacobsen, Anna L; Pratt, R Brandon; Davis, Stephen D

2016-01-01

Chaparral is the most abundant vegetation type in California and current climate change models predict more frequent and severe droughts that could impact plant community structure. Understanding the factors related to species-specific drought mortality is essential to predict such changes. We predicted that life history type, hydraulic traits, and plant size would be related to the ability of species to survive drought. We evaluated the impact of these factors in a mature chaparral stand during the drought of 2014, which has been reported as the most severe in California in the last 1,200 years. We measured tissue water potential, native xylem specific conductivity, leaf specific conductivity, percentage loss in conductivity, and chlorophyll fluorescence for 11 species in February 2014, which was exceptionally dry following protracted drought. Mortality among the 11 dominant species ranged from 0 to 93%. Total stand density was reduced 63.4% and relative dominance of species shifted after the drought. Mortality was negatively correlated with water potential, native xylem specific conductivity, and chlorophyll fluorescence, but not with percent loss in hydraulic conductivity and leaf specific conductivity. The model that best explained mortality included species and plant size as main factors and indicated that larger plants had greater survival for 2 of the species. In general, species with greater resistance to water-stress induced cavitation showed greater mortality levels. Despite adult resprouters typically being more vulnerable to cavitation, results suggest that their more extensive root systems enable them to better access soil moisture and avoid harmful levels of dehydration. These results are consistent with the hypothesis that short-term high intensity droughts have the strongest effect on mature plants of shallow-rooted dehydration tolerant species, whereas deep-rooted dehydration avoiding species fare better in the short-term. Severe droughts can drive changes in chaparral structure as a result of the differential mortality among species.

Thermal Properties of Consolidated Granular Salt as a Backfill Material

NASA Astrophysics Data System (ADS)

Paneru, Laxmi P.; Bauer, Stephen J.; Stormont, John C.

2018-03-01

Granular salt has been proposed as backfill material in drifts and shafts of a nuclear waste disposal facility where it will serve to conduct heat away from the waste to the host rock. Creep closure of excavations in rock salt will consolidate (reduce the porosity of) the granular salt. This study involved measuring the thermal conductivity and specific heat of granular salt as a function of porosity and temperature to aid in understanding how thermal properties will change during granular salt consolidation accomplished at pressures and temperatures consistent with a nuclear waste disposal facility. Thermal properties of samples from laboratory-consolidated granular salt and in situ consolidated granular salt were measured using a transient plane source method at temperatures ranging from 50 to 250 °C. Additional measurements were taken on a single crystal of halite and dilated polycrystalline rock salt. Thermal conductivity of granular salt decreased with increases in temperature and porosity. Specific heat of granular salt at lower temperatures decreased with increasing porosity. At higher temperatures, porosity dependence was not apparent. The thermal conductivity and specific heat data were fit to empirical models and compared with results presented in the literature. At comparable densities, the thermal conductivities of granular salt samples consolidated hydrostatically in this study were greater than those measured previously on samples formed by quasi-static pressing. Petrographic studies of the consolidated salt indicate that the consolidation method influenced the nature of the porosity; these observations are used to explain the variation of measured thermal conductivities between the two consolidation methods. Thermal conductivity of dilated polycrystalline salt was lower than consolidated salt at comparable porosities. The pervasive crack network along grain boundaries in dilated salt impedes heat flow and results in a lower thermal conductivity compared to hydrostatically consolidated salt.

Who Is Conducting Educational Research in Australia and How Can Their Work Be Supported?

ERIC Educational Resources Information Center

Bennett, Dawn; Smith, Erica; Bennett, Sue; Chan, Philip; Bobis, Janette; Harrison, Neil; Seddon, Terri; Shore, Sue

2013-01-01

Educational research has long been the subject of lively and agitated debate, not least because of its diversity. Ranging in scope from academic development and broad-scale policy research through to student engagement and discipline-specific research, it includes methods of traditional academic inquiry and investigations and also less traditional…

Marketing Analysis for the Nontraditional Student at Carl Sandburg College.

ERIC Educational Resources Information Center

Sundberg, Lori

With the wide range of students community colleges must provide services for, there is an increasing need for colleges to analyze and segment their marketing efforts. As part of an effort to focus on specific market segments and take into account internal and external environments, an analysis was conducted at Illinois' Carl Sandburg College (CSC)…

Synthesis, growth, spectral, electrical, mechanical and thermal characterization of a potential optical material: γ-glycine single crystal

NASA Astrophysics Data System (ADS)

Sivakumar, N.; Jayavel, R.; Anbalagan, G.; Yadav, R. R.

2018-06-01

Gamma glycine, an organic material was grown by slow solvent evaporation method. Conventional polythermal method was employed in the temperature range, 30-50 °C to obtain the solubility and the metastable zonewidth. The crystal and molecular structures were analyzed by X-ray powder diffraction, FT-IR and FT-Raman spectral studies. Optical refractive index was determined by prism coupling technique and was found to be 1.4488. Electrical properties such as ac conductivity and activation energy were studied for different temperatures in the frequency range from 40 Hz to 6 MHz. The dc electrical conductivity was estimated from the Cole-Cole plot and the values were found to be 2.19 × 10-6 Sm-1 at 353K and 1.46 × 10-6 Sm-1 at 373K respectively. Mechanical studies on the grown crystal revealed that the material belongs to soft materials category. Thermal conductivity and specific heat capacities were estimated by Hot Disk Thermal Constants Analyzer.

Gamma-Ray Emission in Dissipative Pulsar Magnetospheres: from Theory to Fermi Observations

NASA Technical Reports Server (NTRS)

Kalapotharakos, Konstantinos; Harding, Alice K.; Kazanas, Demosthenes

2014-01-01

We compute the patterns of gamma-ray emission due to curvature radiation in dissipative pulsar magnetospheres. Our ultimate goal is to construct macrophysical models that are able to reproduce the observed gamma-ray light curve phenomenology recently published in the Second Fermi Pulsar Catalog. We apply specific forms of Ohm's law on the open field lines using a broad range for the macroscopic conductivity values that result in solutions ranging, from near-vacuum to near-force-free. Using these solutions, we generate model gamma-ray light curves by calculating realistic trajectories and Lorentz factors of radiating particles under the influence of both the accelerating electric fields and curvature radiation reaction. We further constrain our models using the observed dependence of the phase lags between the radio and gamma-ray emission on the gamma-ray peak separation. We perform a statistical comparison of our model radio-lag versus peak-separation diagram and the one obtained for the Fermi standard pulsars. We find that for models of uniform conductivity over the entire open magnetic field line region, agreement with observations favors higher values of this parameter. We find, however, significant improvement in fitting the data with models that employ a hybrid form of conductivity, specifically, infinite conductivity interior to the light cylinder and high but finite conductivity on the outside. In these models the gamma-ray emission is produced in regions near the equatorial current sheet but modulated by the local physical properties. These models have radio lags near the observed values and statistically best reproduce the observed light curve phenomenology. Additionally, they also produce GeV photon cut-off energies.

Pacemaker Dependency after Cardiac Surgery: A Systematic Review of Current Evidence

PubMed Central

2015-01-01

Background Severe postoperative conduction disturbances requiring permanent pacemaker implantation frequently occur following cardiac surgery. Little is known about the long-term pacing requirements and risk factors for pacemaker dependency in this population. Methods We performed a systematic review of the literature addressing rates and predictors of pacemaker dependency in patients requiring permanent pacemaker implantation after cardiac surgery. Using a comprehensive search of the Medline, Web of Science and EMBASE databases, studies were selected for review based on predetermined inclusion and exclusion criteria. Results A total of 8 studies addressing the endpoint of pacemaker-dependency were identified, while 3 studies were found that addressed the recovery of atrioventricular (AV) conduction endpoint. There were 10 unique studies with a total of 780 patients. Mean follow-up ranged from 6–72 months. Pacemaker dependency rates ranged from 32%-91% and recovery of AV conduction ranged from 16%-42%. There was significant heterogeneity with respect to the definition of pacemaker dependency. Several patient and procedure-specific variables were found to be independently associated with pacemaker dependency, but these were not consistent between studies. Conclusions Pacemaker dependency following cardiac surgery occurs with variable frequency. While individual studies have identified various perioperative risk factors for pacemaker dependency and non-resolution of AV conduction disease, results have been inconsistent. Well-conducted studies using a uniform definition of pacemaker dependency might identify patients who will benefit most from early permanent pacemaker implantation after cardiac surgery. PMID:26470027

Characterization of the relationship of the cure cycle chemistry to cure cycle processing properties

NASA Technical Reports Server (NTRS)

Kranbuehl, D. E.

1985-01-01

Dynamic dielectric analysis (DDA) is used to study curing polymer systems and thermoplastics. Measurements are made over a frequency range of six decades. This wide range of frequencies increases the amount of information which can be obtained. The data is analyzed in terms of the frequency dependence of the complex permittivity epsilon sup *, specific conductivity sigma (ohm/cm) and the relaxation time tau, parameters which are characteristic of the cure state of the material and independent of the size of the sample.

From Archive to Evidence: Historians and Natural Resource Litigation.

PubMed

Stevens, Jennifer A

2015-02-01

Within the field of natural resource law are several specific areas that are well suited for the historian's skillset and knowledge. The deployment of the historian's tool box when conducting research in the legal world, however, can result in deliverables which vary significantly from those found in the academy, as they range widely in both size and scope and do not always use the full range of a historian's skills. New technological platforms provide consulting historians with creative opportunities to disseminate valuable information and sources and enhance important scholarly debates.

Cryogenic Thermal Conductivity Measurements on Candidate Materials for Space Missions

NASA Technical Reports Server (NTRS)

Tuttle, JIm; Canavan, Ed; Jahromi, Amir

2017-01-01

Spacecraft and instruments on space missions are built using a wide variety of carefully-chosen materials. In addition to having mechanical properties appropriate for surviving the launch environment, these materials generally must have thermal conductivity values which meet specific requirements in their operating temperature ranges. Space missions commonly propose to include materials for which the thermal conductivity is not well known at cryogenic temperatures. We developed a test facility in 2004 at NASAs Goddard Space Flight Center to measure material thermal conductivity at temperatures between 4 and 300 Kelvin, and we have characterized many candidate materials since then. The measurement technique is not extremely complex, but proper care to details of the setup, data acquisition and data reduction is necessary for high precision and accuracy. We describe the thermal conductivity measurement process and present results for several materials.

Theoretical Rocket Performance of Liquid Methane with Several Fluorine-Oxygen Mixtures Assuming Frozen Composition

NASA Technical Reports Server (NTRS)

Gordon, Sanford; Kastner, Michael E

1958-01-01

Theoretical rocket performance for frozen composition during expansion was calculated for liquid methane with several fluorine-oxygen mixtures for a range of pressure ratios and oxidant-fuel ratios. The parameters included are specific impulse, combustion-chamber temperature, nozzle-exit temperature molecular weight, characteristic velocity, coefficient of thrust, ratio of nozzle-exit area to throat area, specific heat at constant pressure, isentropic exponent, viscosity, and thermal conductivity. The maximum calculated value of specific impulse for a chamber pressure of 600 pounds per square inch absolute (40.827atm) and an exit pressure of 1 atmosphere is 315.3 for 79.67 percent fluorine in the oxidant.

Construction, Geology, and Aquifer Testing of the Maalo Road, Aahoaka Hill, and Upper Eleele Tank Monitor Wells, Kauai, Hawaii

USGS Publications Warehouse

Izuka, Scot K.

2005-01-01

The Maalo Road, Aahoaka Hill, and Upper Eleele Tank monitor wells were constructed using rotary drilling methods between July 1998 and August 2002 as part of a program of exploratory drilling, aquifer testing, and hydrologic analysis on Kauai. Aquifer tests were conducted in the uncased boreholes of the wells. The Maalo Road monitor well in the Lihue Basin penetrated 915 feet, mostly through mafic lava flows. Most of the rock samples from this well had chemical compositions similar to the Koloa Volcanics, but the deepest sample analyzed had a composition similar to the Waimea Canyon Basalt. Water temperature ranged from 25.6 to 27.4 degrees Celsius and specific conductance ranged from 303 to 627 microsiemens per centimeter during aquifer testing. Discharge rate ranged from 174 to 220 gallons per minute and maximum drawdown was 138.25 ft during a 7-day sustained-discharge test, but the test was affected by pump and generator problems. The Aahoaka Hill monitor well in the Lihue Basin penetrated 804 feet, mostly through mafic lava flows and possibly dikes. The well penetrated rocks having chemical compositions similar to the Waimea Canyon Basalt. During the first three hours of a sustained-discharge aquifer test in which the discharge rate varied between 92 and 117 gallons per minute, water temperature was 24.6 to 25.6 degrees Celsius, and specific conductance was 212 to 238 microsiemens per centimeter; this test was halted after a short period because drawdown was high. In a subsequent 7-day test, discharge was 8 to 23 gallons per minute, and maximum drawdown was 37.71 feet after 1,515 minutes of testing. The Upper Eleele Tank monitor well is near the Hanapepe River Valley. The well penetrated 740 feet through soil, sediment, mafic lava flows, volcanic ash, and scoria. Rocks above a depth of 345 feet had compositions similar to the Koloa Volcanics, but a sample from 720 to 725 feet had a composition similar to rocks of the Waimea Canyon Basalt. During a 7-day aquifer test with a sustained discharge between 278 and 290 gallons per minute, most of the drawdown of 1.10 feet occurred in the first 455 minutes of the test. Water levels measured thereafter may have been influenced by pumping from a nearby well. Water temperature ranged from 20.2 to 21.4 degrees Celsius and specific conductance from 8,380 to 18,940 microsiemens per centimeter during the aquifer tests.

Establishment of new complete blood count reference values for healthy Thai adults.

PubMed

Wongkrajang, P; Chinswangwatanakul, W; Mokkhamakkun, C; Chuangsuwanich, N; Wesarachkitti, B; Thaowto, B; Laiwejpithaya, S; Komkhum, O

2018-04-28

Laboratory reference ranges are essential for diagnostic orientation and treatment decision. As complete blood count parameters are influenced by various factors, including gender, geographic origin, and ethnic origin, it is important to establish specific hematologic reference values for specific populations. This study was conducted at the Department of Clinical Pathology, Faculty of Medicine Siriraj Hospital, Mahidol University, Bangkok, Thailand. Blood samples were taken from healthy adults aged 18-60 years that attended a health check-up program at our hospital during February 2015 to July 2015. Hematologic and routine chemistry analysis were performed. Participants were determined to be healthy based on medical history and routine medical examinations. Serum vitamin B12, folate, ferritin, and hemoglobin typing were also analyzed to exclude the possible presence of anemia. A statistically significant difference was observed between males and females for Hb level, hematocrit level, red blood cell count, mean corpuscular hemoglobin concentration, percentage neutrophils, monocytes and eosinophils, and absolute neutrophil, lymphocyte, basophil, and platelet counts. Accordingly, gender-specific reference intervals were established for all complete blood count parameters in healthy Thai adult population. The reference value ranges established in this study reflect significant differences between genders. It is possible that these reference ranges may be generalizable to adults living in Thailand. The findings of this study emphasize the importance of establishing specific hematologic reference values for specific populations. © 2018 John Wiley & Sons Ltd.

Personal stigma in schizophrenia spectrum disorders: a systematic review of prevalence rates, correlates, impact and interventions

PubMed Central

Gerlinger, Gabriel; Hauser, Marta; De Hert, Marc; Lacluyse, Kathleen; Wampers, Martien; Correll, Christoph U

2013-01-01

A systematic electronic PubMed, Medline and Web of Science database search was conducted regarding the prevalence, correlates, and effects of personal stigma (i.e., perceived and experienced stigmatization and self-stigma) in patients with schizophrenia spectrum disorders. Of 54 studies (n=5,871), published from 1994 to 2011, 23 (42.6%) reported on prevalence rates, and 44 (81.5%) reported on correlates and/or consequences of perceived or experienced stigmatization or self-stigma. Only two specific personal stigma intervention studies were found. On average, 64.5% (range: 45.0–80.0%) of patients perceived stigma, 55.9% (range: 22.5–96.0%) actually experienced stigma, and 49.2% (range: 27.9–77.0%) reported alienation (shame) as the most common aspect of self-stigma. While socio-demographic variables were only marginally associated with stigma, psychosocial variables, especially lower quality of life, showed overall significant correlations, and illness-related factors showed heterogeneous associations, except for social anxiety that was unequivocally associated with personal stigma. The prevalence and impact of personal stigma on individual outcomes among schizophrenia spectrum disorder patients are well characterized, yet measures and methods differ significantly. By contrast, research regarding the evolution of personal stigma through the illness course and, particularly, specific intervention studies, which should be conducted utilizing standardized methods and outcomes, are sorely lacking. PMID:23737425

Fermentation process using specific oxygen uptake rates as a process control

DOEpatents

Van Hoek, Pim; Aristidou, Aristos; Rush, Brian J.

2016-08-30

Specific oxygen uptake (OUR) is used as a process control parameter in fermentation processes. OUR is determined during at least the production phase of a fermentation process, and process parameters are adjusted to maintain the OUR within desired ranges. The invention is particularly applicable when the fermentation is conducted using a microorganism having a natural PDC pathway that has been disrupted so that it no longer functions. Microorganisms of this sort often produce poorly under strictly anaerobic conditions. Microaeration controlled by monitoring OUR allows the performance of the microorganism to be optimized.

Fermentation process using specific oxygen uptake rates as a process control

DOEpatents

Van Hoek, Pim [Minnetonka, MN; Aristidou, Aristos [Maple Grove, MN; Rush, Brian [Minneapolis, MN

2011-05-10

Specific oxygen uptake (OUR) is used as a process control parameter in fermentation processes. OUR is determined during at least the production phase of a fermentation process, and process parameters are adjusted to maintain the OUR within desired ranges. The invention is particularly applicable when the fermentation is conducted using a microorganism having a natural PDC pathway that has been disrupted so that it no longer functions. Microorganisms of this sort often produce poorly under strictly anaerobic conditions. Microaeration controlled by monitoring OUR allows the performance of the microorganism to be optimized.

Fermentation process using specific oxygen uptake rates as a process control

DOEpatents

Hoek, Van; Pim, Aristidou [Minnetonka, MN; Aristos, Rush [Maple Grove, MN; Brian, [Minneapolis, MN

2007-06-19

Specific oxygen uptake (OUR) is used as a process control parameter in fermentation processes. OUR is determined during at least the production phase of a fermentation process, and process parameters are adjusted to maintain the OUR within desired ranges. The invention is particularly applicable when the fermentation is conducted using a microorganism having a natural PDC pathway that has been disrupted so that it no longer functions. Microorganisms of this sort often produce poorly under strictly anaerobic conditions. Microaeration controlled by monitoring OUR allows the performance of the microorganism to be optimized.

Fermentation process using specific oxygen uptake rates as a process control

DOEpatents

Van Hoek, Pim; Aristidou, Aristos; Rush, Brian

2014-09-09

Specific oxygen uptake (OUR) is used as a process control parameter in fermentation processes. OUR is determined during at least the production phase of a fermentation process, and process parameters are adjusted to maintain the OUR within desired ranges. The invention is particularly applicable when the fermentation is conducted using a microorganism having a natural PDC pathway that has been disrupted so that it no longer functions. Microorganisms of this sort often produce poorly under strictly anaerobic conditions. Microaeration controlled by monitoring OUR allows the performance of the microorganism to be optimized.

Water quality and discharge data for St. Joseph Bay, Florida, 1997-98

USGS Publications Warehouse

Berndt, M.P.; Franklin, M.A.

1999-01-01

Historical data were compiled on water quality and water levels for the St. Joseph Bay area to assess quality of possible sources of land-derived water into the Bay. Ground-water quality data were compiled from Florida Department of Environmental Protection and surface-water quality data were compiled from U.S.Geological Survey files. Water-quality and water-level data were measured during two sample collection periods in October 1997 and March 1998 to determine water-quality and discharge rates in St. Joseph Bay under two sets of flow conditions. Measurements in the Bay included water level, temperature, pH, specific conductance, dissolved oxygen, and turbidity. Median pH in water from the surficial, intermediate and Floridan aquifer systems ranged from 4.8 to 7.8, and median specific conductance values were less than 500 microsiemens per centimeter. Median nutrient concentrations-- nitrate plus nitrite, ammonia and phosphorus--in the three aquifers were less than 0.5 milligrams per liter. The median pH was 7.0 and the median specific conductance was 81 microsiemens per centimeter for two samples from the Chipola River distribution canal. Water level data were obtained for several wells near St. Joseph Bay but only two wells yielded sufficient data to plot hydrographs. Measurements in St. Joseph Bay during the October and March collection periods were similar for pH and turbidity but differed for temperature, specific conductance and dissolved oxygen. The median temperature was 20.6 degrees Celsius in October and 15.4 degrees Celsius in March, median specific conductance was 39,500 microsiemens per centimeter in October and 43,300 microsiemens per centimeter in March, and median dissolved oxygen was 7.6 milligrams per liter in October and 8.3 milligrams per liter in March. The range in water levels over a tidal cycle in St. Joseph Bay on October 29, 1997 was about 1 foot. During a 24-hour tidal cycle on October 29, 1997, estimated hourly discharge varied from about -116,000 cubic feet per second (ft3/s) (into the Bay) to about +110,000 ft3/s (out of the Bay). During a 24-hour tidal cycle on March 3, 1998, the water level change was about 1.3 feet and estimated hourly discharge varied from about -132,000 ft3/s (into the Bay) to about +121,000 ft3/s (out of the Bay).

Effects of an Elastic Hamstring Assistance Device During Downhill Running

PubMed Central

Aldret, Randy L; Trahan, Brittany A; Davis, Greggory; Campbell, Brian; Bellar, David M

2017-01-01

Abstract The purpose of this study was to determine the appropriateness of using an elastic hamstring assistance device to reduce perceived levels of soreness, increase isometric strength, increase passive range of motion, and decrease biomarkers of muscle damage after eccentric exercise, specifically, downhill running This study was conducted in a university exercise physiology laboratory placing sixteen apparently healthy males (X = 21.6 ± 2.5 years) into two groups using a pre-test/post-test design. Pre-intervention measures taken included participants’ body height, body mass, body fat, capillary blood samples, VO2max, isometric hamstring strength at 45 and 90 degrees of flexion and passive hamstring range of motion. Post-intervention measures included blood biomarkers, passive range of motion, the perceived level of soreness and isometric strength. An analysis of normality of data was initially conducted followed by multivariate analysis of variance (MANOVA) of hamstring strength at 45 and 90 degrees of flexion, blood myoglobin and passive range of motion of the hamstrings. Statistically significant changes were noted in subject-perceived muscle soreness and isometric strength at 90 degrees at the 24-hour post-exercise trial measure between the two groups. Results would suggest the findings could be explained by the decrease in muscle soreness from utilizing the device during the exercise trial. Further research should be conducted to address sample size issues and to determine if the results are comparable on different surfaces. PMID:28713460

The biological acoustic sensor to record the interactions of the microbial cells with the phage antibodies in conducting suspensions.

PubMed

Guliy, О I; Zaitsev, B D; Borodina, I A; Shikhabudinov, А М; Teplykh, A A; Staroverov, S A; Fomin, A S

2018-02-01

The acoustic biological sensor for the analysis of the bacterial cells in conducting suspension was developed. The sensor represented the two channel delay line based on the piezoelectric plate of Y-X lithium niobate thick of 0.2mm. Two pairs of the interdigital transducers (IDT) for the excitation and reception of shear horizontal acoustic wave of zero order (SH 0 ) in each channel were deposited by the method of photolithography. One channel of the delay line was electrically shorted by the deposition of thin aluminum film between IDTs. The second channel remained as electrically open. The liquid container with the volume of 5ml was fixed on the plate surface between IDTs by the glue, which did not cause the additional insertion loss. For the first time the influence of the conductivity of the cell suspension on the registration of the specific and nonspecific interactions of the bacterial cells with phage-antibodies (phage-Abs) was studied by means of the developed sensor. The dependencies of the change in insertion loss and phase of the output signal on the conductivity of the buffer solution at specific/nonspecific interactions for the electrically open and shorted channels of the delay line were obtained. It was shown that the sensor successfully registered the interactions of microbial cells with phage-Abs in the range of the conductivity of 2-20 μS/cm on the model samples A. brasilense Sp245 - specific phage-Abs. The sensor in the time regime of the operation fast reacted on the specific/nonspecific interaction and the time of the stabilization of the output parameters did not exceed 10min. Copyright © 2017 Elsevier B.V. All rights reserved.

Ground- and Surface-Water Chemistry of Handcart Gulch, Park County, Colorado, 2003-2006

USGS Publications Warehouse

Verplanck, Philip L.; Manning, Andrew H.; Kimball, Briant A.; McCleskey, R. Blaine; Runkel, Robert L.; Caine, Jonathan S.; Adams, Monique; Gemery-Hill, Pamela A.; Fey, David L.

2008-01-01

As part of a multidisciplinary project to determine the processes that control ground-water chemistry and flow in mineralized alpine environments, ground- and surface-water samples from Handcart Gulch, Colorado were collected for analysis of inorganic solutes and water and dissolved sulfate stable isotopes in selected samples. The primary aim of this study was to document variations in ground-water chemistry in Handcart Gulch and to identify changes in water chemistry along the receiving stream of Handcart Gulch. Water analyses are reported for ground-water samples collected from 12 wells in Handcart Gulch, Colorado. Samples were collected between August 2003 and October 2005. Water analyses for surface-water samples are reported for 50 samples collected from Handcart Gulch and its inflows during a low-flow tracer injection on August 6, 2003. In addition, water analyses are reported for three other Handcart Gulch stream samples collected in September 2005 and March 2006. Reported analyses include field parameters (pH, specific conductance, temperature, dissolved oxygen, and Eh), major and trace constituents, oxygen and hydrogen isotopic composition of water and oxygen and sulfur isotopic composition of dissolved sulfate. Ground-water samples from this study are Ca-SO4 type and range in pH from 2.5 to 6.8. Most of the samples (75 percent) have pH values between 3.3 and 4.3. Surface water samples are also Ca-SO4 type and have a narrower range in pH (2.7?4.0). Ground- and surface-water samples vary from relatively dilute (specific conductance of 68 ?S/cm) to concentrated (specific conductance of 2,000 ?S/cm).

Physical and hydrologic characteristics of Matlacha Pass, southwestern Florida

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kane, R.L.; Russell, G.M.

1994-03-01

Matlacha Pass is part of the connected inshore waters of the Charlotte Harbor estuary in southwestern Florida. Bathymetry indicates that depths in the main channel of the pass range from 4 to 14 feet below sea level. The channel averages about 8 feet deep in the northern part of the pass and about 5 feet deep in the southern part. Additionally, depths average about 4 feet in a wide section of the middle of the pass and about 2 feet along the mangrove swamps near the shoreline. Tidal flow within Matlacha Pass varies depending on aquatic vegetation densities, oyster beds,more » and tidal flats. Surface-water runoff occurs primarily during the wet season (May to September), with most of the flow entering the Matlacha Pass through two openings in the spreader canal system near the city of Matlacha. Freshwater flow into the pass from the north Cape Coral spreader canal system averaged 113 cubic feet per second from October 1987 to September 1992. Freshwater inflow from the Aries Canal of the south Cape Coral spreader canal system averaged 14.1 cubic feet per second from October 1989 to September 1992. Specific conductance throughout Matlacha Pass ranged from less than 1,000 to 57,000 microsiemens per centimeter. Specific conductance, collected from a continuous monitoring data logger in the middle of the pass from February to September 1992, averaged 36,000 microsiemens per centimeter at 2 feet below the water surface and 40,000 microsiemens per centimeter at 2 feet above the bottom. During both the wet and dry seasons, specific conductance indicated that the primary mixing of tidal waters and freshwater inflow occurs in the mangrove swamps along the shoreline.« less

English Textbooks for Russian Students: Problems and Specific Features

ERIC Educational Resources Information Center

Solnyshkina, Marina I.; Vishnyakova, Ol'ga D.; Gafiyatova, Elzara V.; Gabitov, Azat I.

2017-01-01

The research identifies the complexity level of eight texts from Spotlight 11 used in Russian TEFL to prepare students for National Unified Exam in English and assess their reading skills. The results of the analyses conducted with the help of T.E.R.A., an automated text processor, prove that all texts fell within the range of 6-9 Flesch-Kincaid…

Preliminary Anthropometric Specification for Land Vehicles

DTIC Science & Technology

2012-05-01

Conducted at 1 BDE Melbourne. Gordon, C. C. (2002). Multivariate anthropometric models for seated workstation design . Contemporary Ergonomics . Gordon...Ideally, the vehicle should safely accommodate (both as operator and passenger ) a large proportion of ADF personnel. Historically, when designing ...key advantage of using human subjects in the ergonomic assessment of a vehicle design is that a full range of tasks, such as vehicle ingress/egress

The Invisible Children of Migrant and Seasonal Farmworkers in the United States: An Examination of Existing Pre-K Partnerships

ERIC Educational Resources Information Center

Academy for Educational Development, 2009

2009-01-01

The National Migrant and Seasonal Head Start Collaboration Office conducted this small scale study to begin to expand, document and disseminate migrant-specific early learning information and to develop a long-range strategy for addressing/increasing collaboration between MSHS and state Pre-Kindergarten programs serving or having the potential to…

Identification, Assessment and Intervention--Implications of an Audit on Dyslexia Policy and Practice in Scotland

ERIC Educational Resources Information Center

Reid, Gavin; Deponio, Pamela; Petch, Louise Davidson

2005-01-01

This article reports on research commissioned by the Scottish Executive Education Department (SEED). It aimed to establish the range and extent of policy and provision in the area of specific learning difficulties (SpLD) and dyslexia throughout Scotland. The research was conducted between January and June 2004 by a team from the University of…

GASP: A computer code for calculating the thermodynamic and transport properties for ten fluids: Parahydrogen, helium, neon, methane, nitrogen, carbon monoxide, oxygen, fluorine, argon, and carbon dioxide. [enthalpy, entropy, thermal conductivity, and specific heat

NASA Technical Reports Server (NTRS)

Hendricks, R. C.; Baron, A. K.; Peller, I. C.

1975-01-01

A FORTRAN IV subprogram called GASP is discussed which calculates the thermodynamic and transport properties for 10 pure fluids: parahydrogen, helium, neon, methane, nitrogen, carbon monoxide, oxygen, fluorine, argon, and carbon dioxide. The pressure range is generally from 0.1 to 400 atmospheres (to 100 atm for helium and to 1000 atm for hydrogen). The temperature ranges are from the triple point to 300 K for neon; to 500 K for carbon monoxide, oxygen, and fluorine; to 600 K for methane and nitrogen; to 1000 K for argon and carbon dioxide; to 2000 K for hydrogen; and from 6 to 500 K for helium. GASP accepts any two of pressure, temperature and density as input conditions along with pressure, and either entropy or enthalpy. The properties available in any combination as output include temperature, density, pressure, entropy, enthalpy, specific heats, sonic velocity, viscosity, thermal conductivity, and surface tension. The subprogram design is modular so that the user can choose only those subroutines necessary to the calculations.

Use of real-time monitoring to predict concentrations of select constituents in the Menomonee River drainage basin, Southeast Wisconsin, 2008-9

USGS Publications Warehouse

Baldwin, Austin K.; Graczyk, David J.; Robertson, Dale M.; Saad, David A.; Magruder, Christopher

2012-01-01

The models to estimate chloride concentrations all used specific conductance as the explanatory variable, except for the model for the Little Menomonee River near Freistadt, which used both specific conductance and turbidity as explanatory variables. Adjusted R2 values for the chloride models ranged from 0.74 to 0.97. Models to estimate total suspended solids and total phosphorus used turbidity as the only explanatory variable. Adjusted R2 values ranged from 0.77 to 0.94 for the total suspended solids models and from 0.55 to 0.75 for the total phosphorus models. Models to estimate indicator bacteria used water temperature and turbidity as the explanatory variables, with adjusted R2 values from 0.54 to 0.69 for Escherichia coli bacteria models and from 0.54 to 0.74 for fecal coliform bacteria models. Dissolved oxygen was not used in any of the final models. These models may help managers measure the effects of land-use changes and improvement projects, establish total maximum daily loads, estimate important water-quality indicators such as bacteria concentrations, and enable informed decision making in the future.

Effect of Moisture Content on Thermal Properties of Porous Building Materials

NASA Astrophysics Data System (ADS)

Kočí, Václav; Vejmelková, Eva; Čáchová, Monika; Koňáková, Dana; Keppert, Martin; Maděra, Jiří; Černý, Robert

2017-02-01

The thermal conductivity and specific heat capacity of characteristic types of porous building materials are determined in the whole range of moisture content from dry to fully water-saturated state. A transient pulse technique is used in the experiments, in order to avoid the influence of moisture transport on measured data. The investigated specimens include cement composites, ceramics, plasters, and thermal insulation boards. The effect of moisture-induced changes in thermal conductivity and specific heat capacity on the energy performance of selected building envelopes containing the studied materials is then analyzed using computational modeling of coupled heat and moisture transport. The results show an increased moisture content as a substantial negative factor affecting both thermal properties of materials and energy balance of envelopes, which underlines the necessity to use moisture-dependent thermal parameters of building materials in energy-related calculations.

The Ames Vertical Gun Range

NASA Technical Reports Server (NTRS)

Karcz, J. S.; Bowling, D.; Cornelison, C.; Parrish, A.; Perez, A.; Raiche, G.; Wiens, J.-P.

2016-01-01

The Ames Vertical Gun Range (AVGR) is a national facility for conducting laboratory- scale investigations of high-speed impact processes. It provides a set of light-gas, powder, and compressed gas guns capable of accelerating projectiles to speeds up to 7 km s(exp -1). The AVGR has a unique capability to vary the angle between the projectile-launch and gravity vectors between 0 and 90 deg. The target resides in a large chamber (diameter approximately 2.5 m) that can be held at vacuum or filled with an experiment-specific atmosphere. The chamber provides a number of viewing ports and feed-throughs for data, power, and fluids. Impacts are observed via high-speed digital cameras along with investigation-specific instrumentation, such as spectrometers. Use of the range is available via grant proposals through any Planetary Science Research Program element of the NASA Research Opportunities in Space and Earth Sciences (ROSES) calls. Exploratory experiments (one to two days) are additionally possible in order to develop a new proposal.

Hydrology of the Cave Springs area near Chattanooga, Hamilton County, Tennessee

USGS Publications Warehouse

Bradfield, Arthur D.

1992-01-01

The hydrology of Cave Springs, the second largest spring in East Tennessee,was investigated from July 1987 to September 1989. Wells near the spring supply about 5 million gallons per day of potable water to people in Hamilton County near Chattanooga. Discharge from the spring averaged about 13.5 cubic feet per second (8.72 million gallons per day) during the study period. Withdrawals by the Hixson Utility District from wells upgradient from the outflow averaged 8.6 cubic feet per second (5.54 million gallons per day). Aquifer tests using wells intersecting a large solution cavity supplying water to the spring showed a drawdown of less than 3 feet with a discharge of 9,000 gallons per minute or 20 cubic feet per second. Temperature and specific conductance of ground water near the spring outflow were monitored hourly. Temperatures ranged from 13.5 to 18.2 degrees celsius, and fluctuated seasonally in response to climate. Specific-conductance values ranged from 122 to 405 microsiemens per centimeter at 25 degrees Celsius, but were generally between 163 to 185 microsiemensper centimeter. The drainage area of the basin recharging the spring system was estimated to be 1O squaremiles. A potentiometric map of the recharge basin was developed from water levels measured at domestic and test wells in August 1989. Aquifer tests at five test wells in the study area indicated that specific-capacity values for these wells ranged from 4.1 to 261 gallons per minute per foot of drawdown. Water-quality characteristics of ground water in the area were used in conjunction with potentiometric-surface maps to delineate the approximate area contributing recharge to Cave Springs.

Individual Foraging Strategies Reveal Niche Overlap between Endangered Galapagos Pinnipeds

PubMed Central

Villegas-Amtmann, Stella; Jeglinski, Jana W. E.; Costa, Daniel P.; Robinson, Patrick W.; Trillmich, Fritz

2013-01-01

Most competition studies between species are conducted from a population-level approach. Few studies have examined inter-specific competition in conjunction with intra-specific competition, with an individual-based approach. To our knowledge, none has been conducted on marine top predators. Sympatric Galapagos fur seals (Arctocephalus galapagoensis) and sea lions (Zalophus wollebaeki) share similar geographic habitats and potentially compete. We studied their foraging niche overlap at Cabo Douglas, Fernandina Island from simultaneously collected dive and movement data to examine spatial and temporal inter- and intra-specific competition. Sea lions exhibited 3 foraging strategies (shallow, intermediate and deep) indicating intra-specific competition. Fur seals exhibited one foraging strategy, diving predominantly at night, between 0–80 m depth and mostly at 19–22 h. Most sea lion dives also occurred at night (63%), between 0–40 m, within fur seals' diving depth range. 34% of sea lions night dives occurred at 19–22 h, when fur seals dived the most, but most of them occurred at dawn and dusk, when fur seals exhibited the least amount of dives. Fur seals and sea lions foraging behavior overlapped at 19 and 21 h between 0–30 m depths. Sea lions from the deep diving strategy exhibited the greatest foraging overlap with fur seals, in time (19 h), depth during overlapping time (21–24 m), and foraging range (37.7%). Fur seals foraging range was larger. Cabo Douglas northwest coastal area, region of highest diving density, is a foraging “hot spot” for both species. Fur seals and sea lions foraging niche overlap occurred, but segregation also occurred; fur seals primarily dived at night, while sea lions exhibited night and day diving. Both species exploited depths and areas exclusive to their species. Niche breadth generally increases with environmental uncertainty and decreased productivity. Potential competition between these species could be greater during warmer periods when prey availability is reduced. PMID:23967096

Method of making a current collector for a sodium/sulfur battery

DOEpatents

Tischer, R.P.; Winterbottom, W.L.; Wroblowa, H.S.

1987-03-10

This specification is directed to a method of making a current collector for a sodium/sulfur battery. The current collector so-made is electronically conductive and resistant to corrosive attack by sulfur/polysulfide melts. The method includes the step of forming the current collector for the sodium/sulfur battery from a composite material formed of aluminum filled with electronically conductive fibers selected from the group of fibers consisting essentially of graphite fibers having a diameter up to 10 microns and silicon carbide fibers having a diameter in a range of 500--1,000 angstroms. 2 figs.

Method of making a current collector for a sodium/sulfur battery

DOEpatents

Tischer, Ragnar P.; Winterbottom, Walter L.; Wroblowa, Halina S.

1987-01-01

This specification is directed to a method of making a current collector (14) for a sodium/sulfur battery (10). The current collector so-made is electronically conductive and resistant to corrosive attack by sulfur/polysulfide melts. The method includes the step of forming the current collector for the sodium/sulfur battery from a composite material (16) formed of aluminum filled with electronically conductive fibers selected from the group of fibers consisting essentially of graphite fibers having a diameter up to 10 microns and silicon carbide fibers having a diameter in a range of 500-1000 angstroms.

Viscosity, density, and thermal conductivity of aluminum oxide and zinc oxide nanolubricants

PubMed Central

Kedzierski, M.A.; Brignoli, R.; Quine, K.T.; Brown, J.S.

2017-01-01

This paper presents liquid kinematic viscosity, density, and thermal conductivity measurements of eleven different synthetic polyolester-based nanoparticle nanolubricants (dispersions) at atmospheric pressure over the temperature range 288 K to 318 K. Aluminum oxide (Al2O3) and zinc oxide (ZnO) nanoparticles with nominal diameters of 127 nm and 135 nm, respectively, were investigated. A good dispersion of the spherical and non-spherical nanoparticles in the lubricant was maintained with a surfactant. Viscosity, density, and thermal conductivity measurements were made for the neat lubricant along with eleven nanolubricants with differing nanoparticle and surfactant mass fractions. Existing models were used to predict kinematic viscosity (±20%), thermal conductivity (±1%), and specific volume (±6%) of the nanolubricant as a function of temperature, nanoparticle mass fraction, surfactant mass fraction, and nanoparticle diameter. The liquid viscosity, density and thermal conductivity were shown to increase with respect to increasing nanoparticle mass fraction. PMID:28736463

Neuromorphic Silicon Neuron Circuits

PubMed Central

Indiveri, Giacomo; Linares-Barranco, Bernabé; Hamilton, Tara Julia; van Schaik, André; Etienne-Cummings, Ralph; Delbruck, Tobi; Liu, Shih-Chii; Dudek, Piotr; Häfliger, Philipp; Renaud, Sylvie; Schemmel, Johannes; Cauwenberghs, Gert; Arthur, John; Hynna, Kai; Folowosele, Fopefolu; Saighi, Sylvain; Serrano-Gotarredona, Teresa; Wijekoon, Jayawan; Wang, Yingxue; Boahen, Kwabena

2011-01-01

Hardware implementations of spiking neurons can be extremely useful for a large variety of applications, ranging from high-speed modeling of large-scale neural systems to real-time behaving systems, to bidirectional brain–machine interfaces. The specific circuit solutions used to implement silicon neurons depend on the application requirements. In this paper we describe the most common building blocks and techniques used to implement these circuits, and present an overview of a wide range of neuromorphic silicon neurons, which implement different computational models, ranging from biophysically realistic and conductance-based Hodgkin–Huxley models to bi-dimensional generalized adaptive integrate and fire models. We compare the different design methodologies used for each silicon neuron design described, and demonstrate their features with experimental results, measured from a wide range of fabricated VLSI chips. PMID:21747754

Theoretical performance of liquid hydrogen and liquid fluorine as a rocket propellant

NASA Technical Reports Server (NTRS)

Gordon, Sanford; Huff, Vearl N

1953-01-01

Theoretical values of performance parameters for liquid hydrogen and liquid fluorine as a rocket propellant were calculated on the assumption of equilibrium composition during the expansion process for a wide range of fuel-oxidant and expansion ratios. The parameters included were specific impulse, combustion-chamber temperature, nozzle-exit temperature, equilibrium composition, mean molecular weight, characteristic velocity, coefficient of thrust, ration of nozzle-exit area to throat area, specific heat at constant pressure, coefficient of viscosity, and coefficient of thermal conductivity. The maximum value of specific impulse was 364.6 pound-seconds per pound for a chamber pressure of 300 pounds per square inch absolute (20.41 atm) and an exit pressure of 1 atmosphere.

Theoretical performance of liquid ammonia and liquid fluorine as a rocket propellant

NASA Technical Reports Server (NTRS)

Gordon, Sanford; Huff, Vearl N

1953-01-01

Theoretical values of performance parameters for liquid ammonia and liquid fluorine as a rocket propellant were calculated on the assumption of equilibrium composition during the expansion process for a wide range of fuel-oxidant and expansion ratios. The parameters included were specific impulse, combustion chamber temperature, nozzle-exit temperature, equilibrium composition, mean molecular weight, characteristic velocity, coefficient of thrust, ratio of nozzle-exit area to throat area, specific heat at constant pressure, coefficient of viscosity, and coefficient of thermal conductivity. The maximum value of specific impulse was 311.5 pound-seconds per pound for a chamber pressure of 300 pounds per square inch absolute (20.41 atm) and an exit pressure of 1 atmosphere.

Current evaluation of the tripropellant concept

NASA Technical Reports Server (NTRS)

Zurawski, R. L.

1986-01-01

An analytical study was conducted to determine the specific-impulse advantages of adding metals to conventional liquid-bipropellant systems. These tripropellant systems theoretically offer higher specific impulse and increased propellant density compared with bipropellant systems. Metals considered were Be, Li, and Al. Bipropellant systems were H2/O2, N2H4/N2O4, RP-1/O2, and H2/F2. Thermochemical calculations were performed for sea-level expansion from 6.895-MN/sq. m. (1000-psia) chamber pressure over a wide range of mixture ratios and propellant compositions. Three-dimensional plots characterize the specific impulse of each tripropellant system. Technology issues pertinent to metallized propellant systems are discussed.

Fano resonances in bilayer graphene superlattices.

PubMed

Briones-Torres, J A; Rodríguez-Vargas, I

2017-12-01

In this work, we address the ubiquitous phenomenon of Fano resonances in bilayer graphene. We consider that this phenomenon is as exotic as other phenomena in graphene because it can arise without an external extended states source or elaborate nano designs. However, there are not theoretical and/or experimental studies that report the impact of Fano resonances on the transport properties. Here, we carry out a systematic assessment of the contribution of the Fano resonances on the transport properties of bilayer graphene superlattices. Specifically, we find that by changing the number of periods, adjusting the barriers height as well as modifying the barriers and wells width it is possible to identify the contribution of Fano resonances on the conductance. Particularly, the coupling of Fano resonances with the intrinsic minibands of the superlattice gives rise to specific and identifiable changes in the conductance. Moreover, by reducing the angular range for the computation of the transport properties it is possible to obtain conductance curves with line-shapes quite similar to the Fano profile and the coupling profile between Fano resonance and miniband states. In fact, these conductance features could serve as unequivocal characteristic of the existence of Fano resonances in bilayer graphene.

Performance Evaluation of a 50kW Hall Thruster

NASA Technical Reports Server (NTRS)

Jacobson, David T.; Jankovsky, Robert S.

1999-01-01

An experimental investigation was conducted on a laboratory model Hall thruster designed to operate at power levels up to 50 kW. During this investigation the engine's performance was characterized over a range of discharge currents from 10 to 36 A and a range of discharge voltages from 200 to 800 V Operating on the Russian cathode a maximum thrust of 966 mN was measured at 35.6 A and 713.0 V. This corresponded to a specific impulse of 3325 s and an efficiency of 62%. The maximum power the engine was operated at was 25 kW. Additional testing was conducted using a NASA cathode designed for higher current operation. During this testing, thrust over 1 N was measured at 40.2 A and 548.9 V. Several issues related to operation of Hall thrusters at these high powers were encountered.

Multiple sclerosis epidemiology in Latin America: An updated survey

PubMed Central

Rojas, Juan Ignacio

2017-01-01

Novel epidemiological data have appeared in recent years in Latin America (LATAM). The objective of this study was to perform an updated systematic review of the epidemiology of the disease reported in LATAM. Methods We conducted a systematic review of published epidemiological articles from January 1995 to December 2016. Results Incidence data were found in four studies and ranged from 0.3 to 3 annual cases per 100,000 person-years. Prevalence was reported in 13 studies and ranged from 0.83 to 38.2 cases per 100,000 inhabitants. Two studies showed an increase in prevalence and incidence in the last five years in specific regions. Conclusion The study provides updated information on epidemiological features of MS in the region. The frequency reported is lower compared with some European and North American countries; however, due to recent observations, studies including follow-up assessment of prevalence and incidence should be conducted in the region. PMID:28638628

System to Measure Thermal Conductivity and Seebeck Coefficient for Thermoelectrics

NASA Technical Reports Server (NTRS)

Kim, Hyun-Jung; Skuza, Jonathan R.; Park, Yeonjoon; King, Glen C.; Choi, Sang H.; Nagavalli, Anita

2012-01-01

The Seebeck coefficient, when combined with thermal and electrical conductivity, is an essential property measurement for evaluating the potential performance of novel thermoelectric materials. However, there is some question as to which measurement technique(s) provides the most accurate determination of the Seebeck coefficient at elevated temperatures. This has led to the implementation of nonstandardized practices that have further complicated the confirmation of reported high ZT materials. The major objective of the procedure described is for the simultaneous measurement of the Seebeck coefficient and thermal diffusivity within a given temperature range. These thermoelectric measurements must be precise, accurate, and reproducible to ensure meaningful interlaboratory comparison of data. The custom-built thermal characterization system described in this NASA-TM is specifically designed to measure the inplane thermal diffusivity, and the Seebeck coefficient for materials in the ranging from 73 K through 373 K.

Thermal Diffusivity and Thermal Conductivity of Dispersed Glass Sphere Composites Over a Range of Volume Fractions

NASA Astrophysics Data System (ADS)

Carson, James K.

2018-06-01

Glass spheres are often used as filler materials for composites. Comparatively few articles in the literature have been devoted to the measurement or modelling of thermal properties of composites containing glass spheres, and there does not appear to be any reported data on the measurement of thermal diffusivities over a range of filler volume fractions. In this study, the thermal diffusivities of guar-gel/glass sphere composites were measured using a transient comparative method. The addition of the glass beads to the gel increased the thermal diffusivity of the composite, more than doubling the thermal diffusivity of the composite relative to the diffusivity of the gel at the maximum glass volume fraction of approximately 0.57. Thermal conductivities of the composites were derived from the thermal diffusivity measurements, measured densities and estimated specific heat capacities of the composites. Two approaches to modelling the effective thermal diffusivity were considered.

A Wide Dynamic Range Tapped Linear Array Image Sensor

NASA Astrophysics Data System (ADS)

Washkurak, William D.; Chamberlain, Savvas G.; Prince, N. Daryl

1988-08-01

Detectors for acousto-optic signal processing applications require fast transient response as well as wide dynamic range. There are two major choices of detectors: conductive or integration mode. Conductive mode detectors have an initial transient period before they reach then' i equilibrium state. The duration of 1 his period is dependent on light level as well as detector capacitance. At low light levels a conductive mode detector is very slow; response time is typically on the order of milliseconds. Generally. to obtain fast transient response an integrating mode detector is preferred. With integrating mode detectors. the dynamic range is determined by the charge storage capability of the tran-sport shift registers and the noise level of the image sensor. The conventional net hod used to improve dynamic range is to increase the shift register charge storage capability. To achieve a dynamic range of fifty thousand assuming two hundred noise equivalent electrons, a charge storage capability of ten million electrons would be required. In order to accommodate this amount of charge. unrealistic shift registers widths would be required. Therefore, with an integrating mode detector it is difficult to achieve a dynamic range of over four orders of magnitude of input light intensity. Another alternative is to solve the problem at the photodetector aml not the shift, register. DALSA's wide dynamic range detector utilizes an optimized, ion implant doped, profiled MOSFET photodetector specifically designed for wide dynamic range. When this new detector operates at high speed and at low light levels the photons are collected and stored in an integrating fashion. However. at bright light levels where transient periods are short, the detector switches into a conductive mode. The light intensity is logarithmically compressed into small charge packets, easily carried by the CCD shift register. As a result of the logarithmic conversion, dynamic ranges of over six orders of magnitide are obtained. To achieve the short integration times necessary in acousto-optic applications. t he wide dynamic range detector has been implemented into a tapped array architecture with eight outputs and 256 photoelements. Operation of each 01)1,1)111 at 16 MHz yields detector integration times of 2 micro-seconds. Buried channel two phase CCD shift register technology is utilized to minimize image sensor noise improve video output rates and increase ease of operation.

Development of a measure of asthma-specific quality of life among adults.

PubMed

Eberhart, Nicole K; Sherbourne, Cathy D; Edelen, Maria Orlando; Stucky, Brian D; Sin, Nancy L; Lara, Marielena

2014-04-01

A key goal in asthma treatment is improvement in quality of life (QoL), but existing measures often confound QoL with symptoms and functional impairment. The current study addresses these limitations and the need for valid patient-reported outcome measures by using state-of-the-art methods to develop an item bank assessing QoL in adults with asthma. This article describes the process for developing an initial item pool for field testing. Five focus group interviews were conducted with a total of 50 asthmatic adults. We used "pile sorting/binning" and "winnowing" methods to identify key QoL dimensions and develop a pool of items based on statements made in the focus group interviews. We then conducted a literature review and consulted with an expert panel to ensure that no key concepts were omitted. Finally, we conducted individual cognitive interviews to ensure that items were well understood and inform final item refinement. Six hundred and sixty-one QoL statements were identified from focus group interview transcripts and subsequently used to generate a pool of 112 items in 16 different content areas. Items covering a broad range of content were developed that can serve as a valid gauge of individuals' perceptions of the effects of asthma and its treatment on their lives. These items do not directly measure symptoms or functional impairment, yet they include a broader range of content than most existent measures of asthma-specific QoL.

Development of a Measure of Asthma-Specific Quality of Life among Adults

PubMed Central

Eberhart, Nicole K.; Sherbourne, Cathy D.; Edelen, Maria Orlando; Stucky, Brian D.; Sin, Nancy L.; Lara, Marielena

2014-01-01

Purpose A key goal in asthma treatment is improvement in quality of life (QoL), but existing measures often confound QoL with symptoms and functional impairment. The current study addresses these limitations and the need for valid patient-reported outcome measures by using state-of-the-art methods to develop an item bank assessing QoL in adults with asthma. This article describes the process for developing an initial item pool for field testing. Methods Five focus group interviews were conducted with a total of 50 asthmatic adults. We used “pile sorting/binning” and “winnowing” methods to identify key QoL dimensions and develop a pool of items based on statements made in the focus group interviews. We then conducted a literature review and consulted with an expert panel to ensure that no key concepts were omitted. Finally, we conducted individual cognitive interviews to ensure that items were well understood and inform final item refinement. Results 661 QoL statements were identified from focus group interview transcripts and subsequently used to generate a pool of 112 items in 16 different content areas. Conclusions Items covering a broad range of content were developed that can serve as a valid gauge of individuals’ perceptions of the effects of asthma and its treatment on their lives. These items do not directly measure symptoms or functional impairment, yet they include a broader range of content than most existent measures of asthma-specific QoL. PMID:24062237

Extrapolation of thermophysical properties data for oxygen to high pressures (5000 to 10,000 psia) at low temperatures (100-600 R)

NASA Technical Reports Server (NTRS)

Weber, L. A.

1971-01-01

Thermophysical properties data for oxygen at pressures below 5000 psia have been extrapolated to higher pressures (5,000-10,000 psia) in the temperature range 100-600 R. The tables include density, entropy, enthalpy, internal energy, speed of sound, specific heat, thermal conductivity, viscosity, thermal diffusivity, Prandtl number, and dielectric constant.

External quality-assurance results for the National Atmospheric Deposition Program/National Trends Network, 1995-96

USGS Publications Warehouse

Gordon, John D.

1999-01-01

The U.S. Geological Survey operated four external quality-assurance programs for the National Atmospheric Deposition Program/National Trends Network (NADP/NTN) in 1995 and 1996: the intersite-comparison program, the blind-audit program, the interlaboratory- comparison program, and the collocated-sampler program. The intersite-comparison program assessed the precision and bias of pH and specific-conductance determinations made by NADP/NTN site operators. The analytical bias introduced during routine handling, processing, and shipping of wet-deposition samples and precision of analyte values was estimated using a blind-audit program. An interlaboratory-comparison program was used to evaluate differences between analytical results and to estimate the analytical precision of five North American laboratories that routinely analyzed wet deposition. A collocated-sampler program estimated the precision of the overall precipitation collection and analysis system from initial sample collection through final storage of the data. Results of two intersite-comparison studies completed in 1995 indicated 94.6 and 94.4 percent of the onsite pH determinations met the NADP/NTN accuracy goals, whereas 97.2 and 98.3 percent of the specific-conductance determinations were within the established limits. The percentages of onsite determinations that met the accuracy goals in 1996 were slightly less for both pH and specific-conductance than in 1995. In 1996, 93.2 and 87.5 percent of onsite pH determinations met the accuracy goals, whereas the percentage of onsite specific-conductance measurements that met the goals was 93.9 and 94.9 percent.The blind audit program utilizes a paired sample design to evaluate the effects of routine sample handling, processing and shipping on the chemistry of weekly precipitation samples. The portion of the blind audit sample subject to all of the normal onsite handling and processing steps of a regular weekly precipitation sample is referred to as the bucket portion, whereas the portion receiving only minimal handling is referred to as the bottle portion. Throughout the report, the term positive bias in regard to blind-audit results indicates that the bucket portion had a higher concentration than the bottle portion. The paired t-test of 1995 blind-audit data indicated that routine sample handling, processing, and shipping introduced a very small positive bias (a=0.05) for hydrogen ion and specific conductance and a slight negative bias (a =0.05) for ammonium and sodium. In 1995, the median paired differences between the bucket and bottle portions ranged from -0.02 milligram per liter for both ammonium and nitrate to +0.002 milligram per liter for calcium. Although the paired t-test indicated a very small positive bias for hydrogen ion, the median paired difference between the bucket and bottle portions was 0.00 microequivalents per liter, whereas for specific conductance, the median paired difference between the bucket and bottle portions was 0.200 microsiemens per centimeter in 1995. The paired t-test of blind-audit results in 1996 indicated statistically significant bias for 6 of the 10 analytes. Only chloride, nitrate, hydrogen ion, and specific conductance were not biased in 1996. However, the magnitude of the bias in 1996 was very small and only of limited importance from the viewpoint of an analytical chemist or data user. The median paired differences between the bucket and bottle portions ranged from -0.02 milligram per liter for both ammonium and chloride to +0.006 milligram per liter for calcium. For hydrogen ion, the median paired difference between the bucket and bottle portions was -0.357 microequivalent per liter; for specific conductance, the median paired difference between the bucket and bottle portions was 0.00 microsiemens per centimeter in 1996. Surface-chemistry effects due to different amounts of precipitation contacting the sample collection and shipping container surfac

Validation of the World Health Organization Enzyme-Linked Immunosorbent Assay for the Quantitation of Immunoglobulin G Serotype-Specific Anti-Pneumococcal Antibodies in Human Serum

PubMed Central

2017-01-01

The World Health Organization (WHO) enzyme-linked immunosorbent assay (ELISA) guideline is currently accepted as the gold standard for the evaluation of immunoglobulin G (IgG) antibodies specific to pneumococcal capsular polysaccharide. We conducted validation of the WHO ELISA for 7 pneumococcal serotypes (4, 6B, 9V, 14, 18C, 19F, and 23F) by evaluating its specificity, precision (reproducibility and intermediate precision), accuracy, spiking recovery test, lower limit of quantification (LLOQ), and stability at the Ewha Center for Vaccine Evaluation and Study, Seoul, Korea. We found that the specificity, reproducibility, and intermediate precision were within acceptance ranges (reproducibility, coefficient of variability [CV] ≤ 15%; intermediate precision, CV ≤ 20%) for all serotypes. Comparisons between the provisional assignments of calibration sera and the results from this laboratory showed a high correlation > 94% for all 7 serotypes, supporting the accuracy of the ELISA. The spiking recovery test also fell within an acceptable range. The quantification limit, calculated using the LLOQ, for each of the serotypes was 0.05–0.093 μg/mL. The freeze-thaw stability and the short-term temperature stability were also within an acceptable range. In conclusion, we showed good performance using the standardized WHO ELISA for the evaluation of serotype-specific anti-pneumococcal IgG antibodies; the WHO ELISA can evaluate the immune response against pneumococcal vaccines with consistency and accuracy. PMID:28875600

Validation of the World Health Organization Enzyme-Linked Immunosorbent Assay for the Quantitation of Immunoglobulin G Serotype-Specific Anti-Pneumococcal Antibodies in Human Serum.

PubMed

Lee, Hyunju; Lim, Soo Young; Kim, Kyung Hyo

2017-10-01

The World Health Organization (WHO) enzyme-linked immunosorbent assay (ELISA) guideline is currently accepted as the gold standard for the evaluation of immunoglobulin G (IgG) antibodies specific to pneumococcal capsular polysaccharide. We conducted validation of the WHO ELISA for 7 pneumococcal serotypes (4, 6B, 9V, 14, 18C, 19F, and 23F) by evaluating its specificity, precision (reproducibility and intermediate precision), accuracy, spiking recovery test, lower limit of quantification (LLOQ), and stability at the Ewha Center for Vaccine Evaluation and Study, Seoul, Korea. We found that the specificity, reproducibility, and intermediate precision were within acceptance ranges (reproducibility, coefficient of variability [CV] ≤ 15%; intermediate precision, CV ≤ 20%) for all serotypes. Comparisons between the provisional assignments of calibration sera and the results from this laboratory showed a high correlation > 94% for all 7 serotypes, supporting the accuracy of the ELISA. The spiking recovery test also fell within an acceptable range. The quantification limit, calculated using the LLOQ, for each of the serotypes was 0.05-0.093 μg/mL. The freeze-thaw stability and the short-term temperature stability were also within an acceptable range. In conclusion, we showed good performance using the standardized WHO ELISA for the evaluation of serotype-specific anti-pneumococcal IgG antibodies; the WHO ELISA can evaluate the immune response against pneumococcal vaccines with consistency and accuracy. © 2017 The Korean Academy of Medical Sciences.

Hydrogeology and results of aquifer tests in the vicinity of a hazardous-waste disposal site near Byron, Illinois

USGS Publications Warehouse

Kay, Robert T.; Olson, David N.; Ryan, Barbara J.

1989-01-01

The U.S. Geological Survey, in cooperation with the U.S. Environmental Protection Agency, conducted an investigation of a Superfund Site near Byron, Illinois. The purpose of the investigation was to determine the hydrogeologic properties of the Galena-Platteville and St. Peter aquifers, the primary water-supply aquifers for domestic supply in the area. The Galena and Platteville Groups and older St. Peter Sandstone are separated by the Harmony Hill Shale Member of the Glenwood Formation. The Harmony Hill Shale Member is a semiconfining unit. Groundwater flow in the study area is from the site northwestward to the Rock River. Movement of groundwater in the dolomites is mainly through joints, fractures, and solution openings. Analysis of the Galena-Platteville aquifer-test data indicates that the calculated aquifer transmissivity ranges from 490 to 670 sq ft/day, and the calculated specific yield ranges from 0.017 to 0.140. Aquifer test data also indicate that the Galena-Platteville aquifer is heterogeneous and anisotropic. Analysis of the St. Peter aquifer-test data indicates that the calculated transmissivity of the aquifer ranges from 1,200 to 1 ,305 sq ft/day, storativity ranges from 0.000528 to 0.00128, horizontal hydraulic conductivity ranges from 2.9 to 3.1 ft/day, and leakage through the Harmony Hill Shale Member ranges from .000123 to .000217 ft/day/ft. (USGS)

Analysis of the electrical and magnetic properties of elastomeric composites and their applicability in small flexible wearable antennas

NASA Astrophysics Data System (ADS)

Al-Sehemi, Abdullah G.; Al-Ghamdi, Ahmed A.; Dishovsky, Nikolay T.; Malinova, Petrunka A.; Atanasov, Nikolay T.; Atanasova, Gabriela L.

2017-07-01

The aim of the research is to obtain conductive elastomer based composites with different degree of filling and specific properties that are applicable for manufacturing of small flexible wearable antennas. The mechanical, electrical and magnetic properties of the composites based on butadiene-acrylonitrile rubber and conductive carbon black have been determined and the possibilities for their use have been analyzed. It has been found that regarding the requirements for elastomer composites application as substrates in such kind of antennas for the 2.4-2.5 GHz frequency range (in respect to the tensile strength, elasticity, volume resistivity, real part of permittivity and permeability, tangent of dielectric and magnetic losses), the most suitable composites are those containing conductive carbon black at 5-10 phr. The prepared composites have been used as monolayered or multilayered substrates for manufacturing prototypes of small flexible wearable antennas for medical, sport and military applications for the 2.4-2.5 GHz frequency range, which demonstrate reliable performance and meet the requirements of the Federal Communication Commission.

Water-quality characteristics and trend analyses for the Tongue, Powder, Cheyenne, and Belle Fourche River drainage basins, Wyoming and Montana, for selected periods, water years 1991 through 2010

USGS Publications Warehouse

Clark, Melanie L.

2012-01-01

The Powder River structural basin in northeastern Wyoming and southeastern Montana is an area of ongoing coalbed natural gas (CBNG) development. Waters produced during CBNG development are managed with a variety of techniques, including surface impoundments and discharges into stream drainages. The interaction of CBNG-produced waters with the atmosphere and the semiarid soils of the Powder River structural basin can affect water chemistry in several ways. Specific conductance and sodium adsorption ratios (SAR) of CBNG-produced waters that are discharged to streams have been of particular concern because they have the potential to affect the use of the water for irrigation. Water-quality monitoring has been conducted since 2001 at main-stem and tributary sites in the Tongue, Powder, Cheyenne, and Belle Fourche River drainage basins in response to concerns about CBNG effects. A study was conducted to summarize characteristics of stream-water quality for water years 2001–10 (October 1, 2000, to September 30, 2010) and examine trends in specific conductance, SAR, and primary constituents that contribute to specific conductance and SAR for changes through time (water years 1991–2010) that may have occurred as a result of CBNG development. Specific conductance and SAR are the focus characteristics of this report. Dissolved calcium, magnesium, and sodium, which are primary contributors to specific conductance and SAR, as well as dissolved alkalinity, chloride, and sulfate, which are other primary contributors to specific conductance, also are described. Stream-water quality in the Tongue, Powder, Cheyenne, and Belle Fourche River drainage basins was variable during water years 2001–10, in part because of variations in streamflow. In general, annual runoff was less than average during water years 2001–06 and near or above average during water years 2007–10. Stream water of the Tongue River had the smallest specific conductance values, sodium adsorption ratios, and major ion concentrations of the main-stem streams. Sites in the Tongue River drainage basin typically had the smallest range of specific conductance and SAR values. The water chemistry of sites in the Powder River drainage basin generally was the most variable as a result of diverse characteristics of that basin. Plains tributaries in the Powder River drainage basin had the largest range of specific conductance and SAR values, in part due to the many tributaries that receive CBNG-produced waters. Trends were analyzed using the seasonal Kendall test with flow-adjusted concentrations to determine changes to water quality through time at sites in the Tongue, Powder, Cheyenne, and Belle Fourche River drainage basins. Trends were evaluated for water years 2001–10 for 17 sites, which generally were on the main-stem streams and primary tributaries. Trends were evaluated for water years 2005–10 for 26 sites to increase the spatial coverage of sites. Trends were evaluated for water years 1991–2010 for eight sites to include water-quality data collected prior to widespread CBNG development and expand the temporal context of trends. Consistent patterns were not observed in trend results for water years 2001–10 for flow-adjusted specific conductance and SAR values in the Tongue, Powder, and Belle Fourche River drainage basins. Significant (p-values less than 0.05) upward trends in flow-adjusted specific conductance values were determined for 3 sites, a downward trend was determined for 1 site, and no significant (p-value greater than 0.05) trends were determined for 13 sites. One of the sites with a significant upward trend was the Tongue River at the Wyoming-Montana State line. No trend in flow-adjusted specific conductance values was determined for the Powder River at Moorhead, Mont. Significant upward trends in flow-adjusted SAR values were determined for 2 sites and no significant trends were determined for 15 sites. No trends in flow-adjusted SAR values were determined for the Tongue River at the Wyoming-Montana State line or for the Powder River at Moorhead, Mont. One of the sites with a significant upward trend in flow-adjusted SAR values was the Powder River at Arvada, Wyo. For water years 2005–10, significant upward trends in flow-adjusted specific conductance values were determined no significant trends were determined for 13 sites. A significant upward trend was determined for flow-adjusted specific conductance values for the Tongue River at the Wyoming-Montana State line. No trend in flow-adjusted specific conductance values was determined for the Powder River at Moorhead, Mont. Significant upward trends in flow-adjusted SAR values were determined for 4 sites, downward trends were determined for 5 sites, and no significant trend was determined for 17 sites. No trends in flow-adjusted SAR values were determined for the Tongue River at the Wyoming-Montana State line or for the Powder River at Moorhead, Mont. Results of the seasonal Kendall test applied to flow-adjusted specific conductance values for water years 1991–2010 indicated no significant trend for eight sites in the Tongue, Powder, and Belle Fourche River drainage basins. No significant trend in flow-adjusted specific conductance was determined for the Tongue River at the Wyoming-Montana State line or the Powder River at Moorhead, Mont. Results of the seasonal Kendall test applied to flow-adjusted SAR values for water years 1991–2010 indicated an upward trend for one site and no significant trend for four sites in the Powder and Belle Fourche River drainage basins. The significant upward trend in flow-adjusted SAR values was determined for the Powder River at Arvada, Wyo., for water years 1991–2010. Results indicate that CBNG development in the Powder River structural basin may have contributed to some trends, such as the upward trend in flow-adjusted SAR for the Powder River at Arvada, Wyo., for water years 1991–2010. An upward trend in flow-adjusted alkalinity concentrations for water years 2001–10 also was determined for the Powder River at Arvada, Wyo. Trend results are consistent with changes that can occur from the addition of sodium and bicarbonate associated with CBNG-produced waters to the Powder River. Upward trends in constituents at other sites, including the Belle Fourche River, may be the result of declining CBNG development, indicating that CBNG-produced waters may have had a dilution effect on some streams. The factors affecting other trends could not be determined because multiple factors could have been affecting the stream-water quality or because trends were observed at sites upstream from CBNG development that may have affected water-quality trends at sites downstream.

Population of computational rabbit-specific ventricular action potential models for investigating sources of variability in cellular repolarisation.

PubMed

Gemmell, Philip; Burrage, Kevin; Rodriguez, Blanca; Quinn, T Alexander

2014-01-01

Variability is observed at all levels of cardiac electrophysiology. Yet, the underlying causes and importance of this variability are generally unknown, and difficult to investigate with current experimental techniques. The aim of the present study was to generate populations of computational ventricular action potential models that reproduce experimentally observed intercellular variability of repolarisation (represented by action potential duration) and to identify its potential causes. A systematic exploration of the effects of simultaneously varying the magnitude of six transmembrane current conductances (transient outward, rapid and slow delayed rectifier K(+), inward rectifying K(+), L-type Ca(2+), and Na(+)/K(+) pump currents) in two rabbit-specific ventricular action potential models (Shannon et al. and Mahajan et al.) at multiple cycle lengths (400, 600, 1,000 ms) was performed. This was accomplished with distributed computing software specialised for multi-dimensional parameter sweeps and grid execution. An initial population of 15,625 parameter sets was generated for both models at each cycle length. Action potential durations of these populations were compared to experimentally derived ranges for rabbit ventricular myocytes. 1,352 parameter sets for the Shannon model and 779 parameter sets for the Mahajan model yielded action potential duration within the experimental range, demonstrating that a wide array of ionic conductance values can be used to simulate a physiological rabbit ventricular action potential. Furthermore, by using clutter-based dimension reordering, a technique that allows visualisation of multi-dimensional spaces in two dimensions, the interaction of current conductances and their relative importance to the ventricular action potential at different cycle lengths were revealed. Overall, this work represents an important step towards a better understanding of the role that variability in current conductances may play in experimentally observed intercellular variability of rabbit ventricular action potential repolarisation.

Population of Computational Rabbit-Specific Ventricular Action Potential Models for Investigating Sources of Variability in Cellular Repolarisation

PubMed Central

Gemmell, Philip; Burrage, Kevin; Rodriguez, Blanca; Quinn, T. Alexander

2014-01-01

Variability is observed at all levels of cardiac electrophysiology. Yet, the underlying causes and importance of this variability are generally unknown, and difficult to investigate with current experimental techniques. The aim of the present study was to generate populations of computational ventricular action potential models that reproduce experimentally observed intercellular variability of repolarisation (represented by action potential duration) and to identify its potential causes. A systematic exploration of the effects of simultaneously varying the magnitude of six transmembrane current conductances (transient outward, rapid and slow delayed rectifier K+, inward rectifying K+, L-type Ca2+, and Na+/K+ pump currents) in two rabbit-specific ventricular action potential models (Shannon et al. and Mahajan et al.) at multiple cycle lengths (400, 600, 1,000 ms) was performed. This was accomplished with distributed computing software specialised for multi-dimensional parameter sweeps and grid execution. An initial population of 15,625 parameter sets was generated for both models at each cycle length. Action potential durations of these populations were compared to experimentally derived ranges for rabbit ventricular myocytes. 1,352 parameter sets for the Shannon model and 779 parameter sets for the Mahajan model yielded action potential duration within the experimental range, demonstrating that a wide array of ionic conductance values can be used to simulate a physiological rabbit ventricular action potential. Furthermore, by using clutter-based dimension reordering, a technique that allows visualisation of multi-dimensional spaces in two dimensions, the interaction of current conductances and their relative importance to the ventricular action potential at different cycle lengths were revealed. Overall, this work represents an important step towards a better understanding of the role that variability in current conductances may play in experimentally observed intercellular variability of rabbit ventricular action potential repolarisation. PMID:24587229

[Clinical characteristics of Rett Syndrome].

PubMed

Abbes, Zeineb; Bouden, Asma; Halayem, Soumaya; Othman, Sami; Bechir Halayem, Mohamed

2011-10-01

Rett Syndrome is a neurodevelopmental disorder, one of the least commonly occurring autism spectrum disorders (ASD),affecting mainly females. To describe features and molecular specificities of Rett syndrome. To identify articles for this review, a Pubmed search was conducted using the following keywords: Rett syndrome, regression,mutation, stereotypes. This syndrome is characterized by cognitive impairment,communication dysfunction, stereotypic movement disorder, and growth failure. It is generally caused by mutations in the MECP2 gene. Rett Syndrome has a prevalence ranging from 10-20 000 females. Specific treatment is not available, but patients need a careful planning for long-term care, with multidisciplinary approaches.

A mobile app for military operational entomology pesticide applications.

PubMed

Britch, Seth C; Linthicum, Kenneth J; Aldridge, Robert L; Yans, Matthew W; Hill, David W; Obenauer, Peter J; Hoffman, Eric R

2014-09-01

Multiple field studies conducted for the Deployed War-Fighter Protection (DWFP) research program have generated more than 80 specific guidance points for innovative combinations of pesticide application equipment, pesticide formulations, and application techniques for aerosol and residual pesticide treatments in 6 ecological regions against a range of mosquito, sand fly, and filth fly nuisance and disease-vector threats. To synthesize and operationalize these DWFP field and laboratory efficacy data we developed an interactive iOS and Android mobile software application, the Pesticide App, consisting of specific pesticide application guidance organized by environment and target insect vector species.

Environmental setting of benchmark streams in agricultural areas of eastern Wisconsin

USGS Publications Warehouse

Rheaume, S.J.; Stewart, J.S.; Lenz, B.N.

1996-01-01

Differences in land use/land cover, and riparian vegetation and instream habitat characteristics are presented. Summaries of field measurements of water temperature, pH, specific conductance and concentrations of dissolved oxygen, total organic plus ammonia nitrogen, dissolved ammonium, nitrate plus nitrte as nitrogen, total phosphorus, dissolved orthophosphate, and atrazine are listed. Concentrations of dissolved oxygen for the sampled streams ranged from 6 A to 14.3 and met the standards set by the Wisconsin Department of Natural Resources (WDNR) for supporting fish and aquatic life. Specific conductance ranged from 98 to 753 u,Scm with values highest in RHU's 1 and 3, where streams are underlain by carbonate bedrock. Median pH did not vary greatly among the four RHU's and ranged from 6.7 to 8.8 also meeting the WDNR standards. Concentrations of total organic plus ammonia nitrogen, dissolved ammonium, total phosphorus, and dissolved orthophosphate show little variation between streams and are generally low, compared to concentrations measured in agriculturally-affected streams in the same RHU's during the same sampling period. Concentrations of the most commonly used pesticide in the study unit, atrazine, were low in all streams, and most concentrations were below trn 0.1 u,g/L detection limit. Riparian vegetation for the benchmark streams were characterized by lowland species of the native plant communities described by John T. Curtis in the "Vegetation of Wisconsin." Based on the environmental setting and water-quality information collected to date, these streams appear to show minimal adverse effects from human activity.

Thermophysical Properties of Alloy 617 from 25°C to 1000°C

DOE Office of Scientific and Technical Information (OSTI.GOV)

B. H. Rabin; R. N. Wright; W. D. Swank

2013-09-01

Key thermophysical properties needed for the successful design and use of Alloy 617 in steam generator and heat exchanger applications have been measured experimentally, and results are compared with literature values and results obtained from some other commercial Ni–Cr alloys and model materials. Specifically, the thermal diffusivity, thermal expansion coefficient, and specific heat capacity have been measured for Alloy 617 over a range of temperatures, allowing calculation of thermal conductivity up to 1000 degrees C. It has been found that the thermal conductivity of Alloy 617 exhibits significant deviation from monotonic behavior in the temperature range from 600 degrees Cmore » to 850 degrees C, the temperatures of interest for most heat transfer applications. The non-linear behavior appears to result primarily from short-range order/disorder phenomena known to occur in the Ni–Cr system. Similar deviation from monotonic behavior was observed in the solid solution Ni–Cr-W Alloy 230, and lesser deviations were observed in iron based Alloy 800H and an austenitic stainless steel. Measured thermophysical property data are provided for four different heats of Alloy 617, and it is shown that property variations between the four different heats are not significant. Measurements were also obtained from Alloy 617 that was aged for up to 2000 h at 750 degrees C, and it was found that this aging treatment does not significantly influence the thermophysical properties.« less

Flow Matching Results of an MHD Energy Bypass System on a Supersonic Turbojet Engine Using the Numerical Propulsion System Simulation (NPSS) Environment

NASA Technical Reports Server (NTRS)

Benyo, Theresa L.

2011-01-01

Flow matching has been successfully achieved for an MHD energy bypass system on a supersonic turbojet engine. The Numerical Propulsion System Simulation (NPSS) environment helped perform a thermodynamic cycle analysis to properly match the flows from an inlet employing a MHD energy bypass system (consisting of an MHD generator and MHD accelerator) on a supersonic turbojet engine. Working with various operating conditions (such as the applied magnetic field, MHD generator length and flow conductivity), interfacing studies were conducted between the MHD generator, the turbojet engine, and the MHD accelerator. This paper briefly describes the NPSS environment used in this analysis. This paper further describes the analysis of a supersonic turbojet engine with an MHD generator/accelerator energy bypass system. Results from this study have shown that using MHD energy bypass in the flow path of a supersonic turbojet engine increases the useful Mach number operating range from 0 to 3.0 Mach (not using MHD) to a range of 0 to 7.0 Mach with specific net thrust range of 740 N-s/kg (at ambient Mach = 3.25) to 70 N-s/kg (at ambient Mach = 7). These results were achieved with an applied magnetic field of 2.5 Tesla and conductivity levels in a range from 2 mhos/m (ambient Mach = 7) to 5.5 mhos/m (ambient Mach = 3.5) for an MHD generator length of 3 m.

Performance characteristics of high-conductivity channel electron multipliers. [as UV and x ray detector

NASA Technical Reports Server (NTRS)

Timothy, J. G.; Bybee, R. L.

1978-01-01

The paper describes a new type of continuous channel multiplier (CEM) fabricated from a low-resistance glass to produce a high-conductivity channel section and thereby obtain a high count-rate capability. The flat-cone cathode configuration of the CEM is specifically designed for the detection of astigmatic exit images from grazing-incidence spectrometers at the optimum angle of illumination for high detection efficiencies at XUV wavelengths. Typical operating voltages are in the range of 2500-2900 V with stable counting plateau slopes in the range 3-6% per 100-V increment. The modal gain at 2800 V was typically in the range (50-80) million. The modal gain falls off at count rates in excess of about 20,000 per sec. The detection efficiency remains essentially constant to count rates in excess of 2 million per sec. Higher detection efficiencies (better than 20%) are obtained by coating the CEM with MgF2. In life tests of coated CEMs, no measurable change in detection efficiency was measured to a total accumulated signal of 2 times 10 to the 11th power counts.

An expanded ostracod-based conductivity transfer function for climate reconstruction in the Levant

NASA Astrophysics Data System (ADS)

Mischke, Steffen; Almogi-Labin, Ahuva; Al-Saqarat, Bety; Rosenfeld, Arik; Elyashiv, Hadar; Boomer, Ian; Stein, Mordechai; Lev, Lilach; Ito, Emi

2014-06-01

We present the first modern calibration dataset linking ostracod assemblage composition to water chemistry, and other site-specific variables, in the hydrologically and geopolitically sensitive southern Levant region. A total of 42 ostracod taxa were recorded from the 178 sampled sites in Israel and Jordan. Ilyocypris spp., Heterocypris salina and Cypridopsis vidua are the most abundant taxa. Species strictly confined to freshwater conditions are Prionocypris zenkeri, Gomphocythere ortali and Prionocypris olivaceus. In contrast, H. salina, Bradleytriebella lineata and Cyprideis torosa show high frequencies in brackish waters (waters with higher conductivity). Humphcypris subterranea, G. ortali, P. olivaceus and Cypridopsis elongata apparently prefer flowing waters. Specific conductivity optima and tolerance ranges were calculated for the recorded ostracod species and may be used for the palaeoenvironmental assessment of fossil ostracod assemblages. In addition, a transfer-function for quantitative specific conductivity estimation based on 141 samples was established with weighted averaging partial least squares regression (WA-PLS). The resulting coefficient of determination r2 between observed and predicted conductivity values (0.72) and the root-mean-square error of prediction (RMSEP) in % gradient length (13.1) indicate that conductivity may be reliably estimated from ostracod assemblage data. The transfer function was first applied to last glacial ostracod assemblage data from an archaeological trench in the Sea of Galilee (northern Israel). Relatively large conductivity fluctuations between ca 1 and 7 mS cm-1 were inferred for the period 24-20 cal ka BP. In addition, four episodes of freshwater influx near the site of the trench were identified from the presence of shells of freshwater and stream-dwelling species intermingled with very abundant shells of Cyprideis torosa. The results of our study allow a better use of Quaternary ostracods from the Levant as palaeoenvironmental indicators of water-body types and past conductivity levels and will contribute to a better understanding of Quaternary environmental and climate change in the Levant.

Validation of the PedsQL Epilepsy Module: A pediatric epilepsy-specific health-related quality of life measure.

PubMed

Modi, Avani C; Junger, Katherine F; Mara, Constance A; Kellermann, Tanja; Barrett, Lauren; Wagner, Janelle; Mucci, Grace A; Bailey, Laurie; Almane, Dace; Guilfoyle, Shanna M; Urso, Lauryn; Hater, Brooke; Hustzi, Heather; Smith, Gigi; Herrmann, Bruce; Perry, M Scott; Zupanc, Mary; Varni, James W

2017-11-01

To validate a brief and reliable epilepsy-specific, health-related quality of life (HRQOL) measure in children with various seizure types, treatments, and demographic characteristics. This national validation study was conducted across five epilepsy centers in the United States. Youth 5-18 years and caregivers of youth 2-18 years diagnosed with epilepsy completed the PedsQL Epilepsy Module and additional questionnaires to establish reliability and validity of the epilepsy-specific HRQOL instrument. Demographic and medical data were collected through chart reviews. Factor analysis was conducted, and internal consistency (Cronbach's alphas), test-retest reliability, and construct validity were assessed. Questionnaires were analyzed from 430 children with epilepsy (M age = 9.9 years; range 2-18 years; 46% female; 62% white: non-Hispanic; 76% monotherapy, 54% active seizures) and their caregivers. The final PedsQL Epilepsy Module is a 29-item measure with five subscales (i.e., Impact, Cognitive, Sleep, Executive Functioning, and Mood/Behavior) with parallel child and caregiver reports. Internal consistency coefficients ranged from 0.70-0.94. Construct validity and convergence was demonstrated in several ways, including strong relationships with seizure outcomes, antiepileptic drug (AED) side effects, and well-established measures of executive, cognitive, and emotional/behavioral functioning. The PedsQL Epilepsy Module is a reliable measure of HRQOL with strong evidence of its validity across the epilepsy spectrum in both clinical and research settings. Wiley Periodicals, Inc. © 2017 International League Against Epilepsy.

What gross weight and range for an advanced HSCT?

NASA Technical Reports Server (NTRS)

Driver, Cornelius

1992-01-01

A review of studies conducted in 1986 indicates that a 300 passenger, 5500 nautical mile range aircraft should weigh less than 400,000 pounds. Some data from a British Aerospace Society of Automotive Engineers (SAE) paper will be shown that purport to be an advanced Concorde that meets the range payload specifications at a gross weight of 360,000 pounds. Previous studies by Peter Coen of Langley Research Center support these results. The weight of a supersonic transport is important from the point of view of how much effort should be expended in developing lower sonic boom technologies. It is obvious that a 360,000 pound aircraft can be modified to a more acceptable boom level than a 700,000 pound one.

Small Launch Vehicle Concept Development for Affordable Multi-Stage Inline Configurations

NASA Technical Reports Server (NTRS)

Beers, Benjamin R.; Waters, Eric D.; Philips, Alan D.; Threet, Grady E., Jr.

2014-01-01

The Advanced Concepts Office at NASA's George C. Marshall Space Flight Center conducted a study of two configurations of a three stage, inline, liquid propellant small launch vehicle concept developed on the premise of maximizing affordability by targeting a specific payload capability range based on current industry demand. The initial configuration, NESC-1, employed liquid oxygen as the oxidizer and rocket propellant grade kerosene as the fuel in all three stages. The second and more heavily studied configuration, NESC-4, employed liquid oxygen and rocket propellant grade kerosene on the first and second stages and liquid oxygen and liquid methane fuel on the third stage. On both vehicles, sensitivity studies were first conducted on specific impulse and stage propellant mass fraction in order to baseline gear ratios and drive the focus of concept development. Subsequent sensitivity and trade studies on the NESC-4 configuration investigated potential impacts to affordability due to changes in gross liftoff weight and/or vehicle complexity. Results are discussed at a high level to understand the severity of certain sensitivities and how those trade studies conducted can either affect cost, performance or both.

Small Launch Vehicle Concept Development for Affordable Multi-Stage Inline Configurations

NASA Technical Reports Server (NTRS)

Beers, Benjamin R.; Waters, Eric D.; Philips, Alan D.; Threet, Grady E. Jr.

2013-01-01

The Advanced Concepts Office at NASA's George C. Marshall Space Flight Center conducted a study of two configurations of a three-stage, inline, liquid propellant small launch vehicle concept developed on the premise of maximizing affordability by targeting a specific payload capability range based on current industry demand. The initial configuration, NESC-1, employed liquid oxygen as the oxidizer and rocket propellant grade kerosene as the fuel in all three stages. The second and more heavily studied configuration, NESC-4, employed liquid oxygen and RP-1 on the first and second stages and liquid oxygen and liquid methane fuel on the third stage. On both vehicles, sensitivity studies were first conducted on specific impulse and stage propellant mass fraction in order to baseline gear ratios and drive the focus of concept development. Subsequent sensitivity and trade studies on the NESC-4 concept investigated potential impacts to affordability due to changes in gross liftoff weight and/or vehicle complexity. Results are discussed at a high level to understand the impact severity of certain sensitivities and how those trade studies conducted can either affect cost, performance, or both.

Assessment of water-quality data from Long Lake National Wildlife Refuge, North Dakota--2008 through 2012

USGS Publications Warehouse

Tangen, Brian A.; Finocchiaro, Raymond G.; Gleason, Robert A.; Rabenberg, Michael J.; Dahl, Charles F.; Ell, Mike J.

2013-01-01

ong Lake National Wildlife Refuge, located in south-central North Dakota, is an important habitat for numerous migratory birds and waterfowl, including several threatened or endangered species. The refuge is distinguished by Long Lake, which is approximately 65 square kilometers and consists of four primary water management units. Water levels in the Long Lake units are maintained by low-level dikes and water-control structures, which after construction during the 1930s increased the water-storage capacity of Long Lake and reduced the frequency and volume of flushing flows downstream. The altered water regime, along with the negative precipitation:evaporation ratio of the region, may be contributing to the accumulation of water-borne chemical constituents such as salts, trace metals, and other constituents, which at certain threshold concentrations may impair aquatic plant, invertebrate, and bird communities of the refuge. The refuge’s comprehensive conservation planning process identified the need for water-quality monitoring to assess current (2013) conditions, establish comparative baselines, evaluate changes over time (trends), and support adaptive management of the wetland units. In 2008, the U.S. Geological Survey, U.S. Fish and Wildlife Service, and North Dakota Department of Health began a water-quality monitoring program at Long Lake National Wildlife Refuge to address these needs. Biweekly water-quality samples were collected for ions, trace metals, and nutrients; and in situ sensors and data loggers were installed for the continuous measurement of specific conductance and water depth. Long Lake was characterized primarily by sodium, bicarbonate, and sulfate ions. Overall results for total alkalinity and hardness were 580 and 329 milligrams per liter, respectively; thus, Long Lake is considered alkaline and classified as very hard. The mean pH and sodium adsorption ratio for Long Lake were 8.8 and 10, respectively. Total dissolved solids concentrations averaged approximately 1,750 milligrams per liter, and ranged from 117 to 39,700 milligrams per liter. Twelve of the 14 trace metals detected in the water samples had established North Dakota water-quality standards for aquatic life, and only aluminum and copper consistently exceeded these criteria. Aluminum is considered harmful to aquatic biota in acidic (pH less than 5.5) systems and most of the copper standard exceedances were collected from highly concentrated waters because of evaporation and seasonally low water levels. Concentrations for various forms of nitrogen and phosphorus generally were similar to reported regional values. Specific conductance of Long Lake varied seasonally and annually both within and among management units, with values ranging from less than 500 to nearly 40,000 microsiemens per centimeter at 25 degrees Celsius. Long Lake was characterized by consistent seasonal patterns of increasing specific conductance from spring (March and April) to fall (September and October), with levels stabilizing through the end of the sampling season (November). These seasonal patterns in specific conductance were associated with decreasing water levels throughout the summer due primarily to evaporation and continuous water releases through the Unit 1 outlet structure, which resulted in the concentration of salts. Specific conductance of each unit, along with water levels, also varied among years. Overall, specific conductance levels were greatest during the drier year of 2008 when water levels were low. Specific conductance levels were lowest during the spring of 2009 following above-average volumes of fresh water from snowmelt runoff. Comparisons of specific conductance among sample sites that were spatially distributed within each management unit suggested that spatial variability within units was low except for areas associated with local inflows. Data collected during this study revealed consistent seasonal patterns and low within-unit spatial variability of specific conductance. Based on these data results, future sample collection efforts may be reduced, as well as the number of sample locations, to limit sampling costs. Water-quality samples collected monthly or seasonally during the growing season (spring, summer, and fall) from a single representative location within each water-management unit should provide sufficient data to assess seasonal changes in water-quality over time and provide information for Long Lake management decisions.

Light sensors for objective light measurement in ambulatory polysomnography.

PubMed

Schembri, Rachel; Spong, Jo; Peters, Allison; Rochford, Peter; Wilksch, Philip; O'Donoghue, Fergal J; Greenwood, Kenneth M; Barnes, Maree; Kennedy, Gerard A; Berlowitz, David J

2017-01-01

Ambulatory polysomnography (PSG) does not commonly include an objective measure of light to determine the time of lights off (Loff), and thus cannot be used to calculate important indices such as sleep onset latency and sleep efficiency. This study examined the technical specifications and appropriateness of a prototype light sensor (LS) for use in ambulatory Compumedics Somte PSG.Two studies were conducted. The first examined the light measurement characteristics of the LS when used with a portable PSG device, specifically recording trace range, linearity, sensitivity, and stability. This involved the LS being exposed to varying incandescent and fluorescent light levels in a light controlled room. Secondly, the LS was trialled in 24 home and 12 hospital ambulatory PSGs to investigate whether light levels in home and hospital settings were within the recording range of the LS, and to quantify the typical light intensity reduction at the time of Loff. A preliminary exploration of clinical utility was also conducted. Linearity between LS voltage and lux was demonstrated, and the LS trace was stable over 14 hours of recording. The observed maximum voltage output of the LS/PSG device was 250 mV, corresponding to a maximum recording range of 350 lux and 523 lux for incandescent and fluorescent light respectively. At the time of Loff, light levels were within the recording range of the LS, and on average dropped by 72 lux (9-245) in the home and 76 lux (4-348) in the hospital setting. Results suggest that clinical utility was greatest in hospital settings where patients are less mobile. The LS was a simple and effective objective marker of light level in portable PSG, which can be used to identify Loff in ambulatory PSG. This allows measurement of additional sleep indices and support with clinical decisions.

Selecting among competing models of electro-optic, infrared camera system range performance

USGS Publications Warehouse

Nichols, Jonathan M.; Hines, James E.; Nichols, James D.

2013-01-01

Range performance is often the key requirement around which electro-optical and infrared camera systems are designed. This work presents an objective framework for evaluating competing range performance models. Model selection based on the Akaike’s Information Criterion (AIC) is presented for the type of data collected during a typical human observer and target identification experiment. These methods are then demonstrated on observer responses to both visible and infrared imagery in which one of three maritime targets was placed at various ranges. We compare the performance of a number of different models, including those appearing previously in the literature. We conclude that our model-based approach offers substantial improvements over the traditional approach to inference, including increased precision and the ability to make predictions for some distances other than the specific set for which experimental trials were conducted.

Preliminary analysis of aircraft fuel systems for use with broadened specification jet fuels

NASA Technical Reports Server (NTRS)

Pasion, A. J.; Thomas, I.

1977-01-01

An analytical study was conducted on the use of broadened specification hydrocarbon fuels in present day aircraft. A short range Boeing 727 mission and three long range Boeing 747 missions were used as basis of calculation for one-day-per-year extreme values of fuel loading, airport ambient and altitude ambient temperatures with various seasonal and climatic conditions. Four hypothetical fuels were selected; two high-vapor-pressure fuels with 35 kPa and 70 kPa RVP and two high-freezing-point fuels with -29 C and -18 C freezing points. In-flight fuel temperatures were predicted by Boeing's aircraft fuel tank thermal analyzer computer program. Boil-off rates were calculated for the high vapor pressure fuels and heating/insulation requirements for the high freezing point fuels were established. Possible minor and major heating system modifications were investigated with respect to heat output, performance and economic penalties for the high freezing point fuels.

Giant Paramagnetism of Copper Nanoparticles in Nanocomposites Cu@C

NASA Astrophysics Data System (ADS)

Sharoyan, Eduard; Mirzakhanyan, Armen; Gyulasaryan, Harutyun; Manukyan, Aram; Estiphanos, Medhanie; Goff, Michael; Bernal, Oscar; Kocharian, Armen

The copper nanoparticles in nanocomposites Cu@C, encapsulated in graphitized carbon shell was obtained by the solid-phase pyrolysis method of polycrystalline phthalocyanine (CuPc, Pc =C32N8H16) . The average sizes of the nanoparticles are in the range of 2-6 nm. Magnetic measurements were carried out by vibrational magnetometer in the temperature range 10-300 K. At low temperatures (<70K) we observed a giant paramagnetism, apparently due to the (ballistic) conduction electron (large orbital magnetism). The values of the specific susceptibility at T = 10K with magnetic specific susceptibility of 510-5 emu/gOe order. This work was supported by the RA MES State Committee of Science, in the frames of the research project SCS-13-1C090. The work at California State University was supported by the National Science Foundation-Partnerships for Research and Education in Materials under Grant DMR-1523588.

Thermoelectric power of PrMg3

NASA Astrophysics Data System (ADS)

Isikawa, Yosikazu; Somiya, Kazuya; Koyanagi, Huruto; Mizushima, Toshio; Kuwai, Tomohiko; Tayama, Takashi

2010-01-01

PrMg3 is supposed to be one of the strongly correlated electron systems originated from the hybridization between the Pr 4f and conduction electrons, because the gigantic electronic specific heat coefficient C/T was observed at low temperatures. However, a typical behaviour of - ln T dependence was not observed in the temperature dependence of the electrical resistivity. The thermoelectric power S is a powerful tool to investigate the density of states at the Fermi energy. We measured carefully the thermoelectric power of PrMg3 in the temperature range between 2 and 300 K. S is extremely small, ranged within ±1 μV/K over the whole temperature. The value of S/T at low temperature limit was also significantly smaller than expected from the specific heat results. We therefore conclude that the density of state at the Fermi level is not enhanced in PrMg3.

Increasing the Thermal Conductivity and Thermal Diffusivity of Asbestos-Reinforced Laminates Through Modification of their Polymer Matrix with Carbon Nanomaterials

NASA Astrophysics Data System (ADS)

Danilova-Tret'yak, S. M.; Evseeva, L. E.; Tanaeva, S. A.

2014-11-01

Experimental investigations of the thermophysical properties of traditional and modified asbestos-reinforced laminates depending on the type of their carbon nanofiller have been carried out in the range of temperatures from -150 to 150°C. It has been shown that the largest (nearly twofold) increase in the thermal-conductivity and thermal-diffusivity coefficients of the indicated materials is observed when they are modified with a small-scale fraction of a nanofiller (carbon nanotubes). The specific heats of the modified and traditional asbestos-reinforced laminates turned out to be identical, in practice, within the measurement error.

Calibration of a modified temperature-light intensity logger for quantifying water electrical conductivity

NASA Astrophysics Data System (ADS)

Gillman, M. A.; Lamoureux, S. F.; Lafrenière, M. J.

2017-09-01

The Stream Temperature, Intermittency, and Conductivity (STIC) electrical conductivity (EC) logger as presented by Chapin et al. (2014) serves as an inexpensive (˜50 USD) means to assess relative EC in freshwater environments. This communication demonstrates the calibration of the STIC logger for quantifying EC, and provides examples from a month long field deployment in the High Arctic. Calibration models followed multiple nonlinear regression and produced calibration curves with high coefficient of determination values (R2 = 0.995 - 0.998; n = 5). Percent error of mean predicted specific conductance at 25°C (SpC) to known SpC ranged in magnitude from -0.6% to 13% (mean = -1.4%), and mean absolute percent error (MAPE) ranged from 2.1% to 13% (mean = 5.3%). Across all tested loggers we found good accuracy and precision, with both error metrics increasing with increasing SpC values. During 10, month-long field deployments, there were no logger failures and full data recovery was achieved. Point SpC measurements at the location of STIC loggers recorded via a more expensive commercial electrical conductivity logger followed similar trends to STIC SpC records, with 1:1.05 and 1:1.08 relationships between the STIC and commercial logger SpC values. These results demonstrate that STIC loggers calibrated to quantify EC are an economical means to increase the spatiotemporal resolution of water quality investigations.

Evaluation of the Hydrolab HL4 water-quality sonde and sensors

USGS Publications Warehouse

Snazelle, Teri T.

2017-12-18

The U.S. Geological Survey (USGS) Hydrologic Instrumentation Facility evaluated three Hydrolab HL4 multiparameter water-quality sondes by OTT Hydromet. The sondes were equipped with temperature, conductivity, pH, dissolved oxygen (DO), and turbidity sensors. The sensors were evaluated for compliance with the USGS National Field Manual for the Collection of Water-Quality Data (NFM) criteria for continuous water-quality monitors and to verify the validity of the manufacturer’s technical specifications. The conductivity sensors were evaluated for the accuracy of the specific conductance (SC) values (conductance at 25 degrees Celsius [oC]), that were calculated by using the vendor default method, Hydrolab Fresh. The HL4’s communication protocols and operating temperature range along with accuracy of the water-quality sensors were tested in a controlled laboratory setting May 1–19, 2016. To evaluate the sonde’s performance in a surface-water field application, an HL4 equipped with temperature, conductivity, pH, DO, and turbidity sensors was deployed June 20–July 22, 2016, at USGS water-monitoring site 02492620, Pearl River at National Space Technology Laboratories (NSTL) Station, Mississippi, located near Bay Saint Louis, Mississippi, and compared to the adjacent well-maintained EXO2 site sonde.The three HL4 sondes met the USGS temperature testing criteria and the manufacturer’s technical specifications for temperature based upon the median room temperature difference between the measured and standard temperatures, but two of the three sondes exceeded the allowable difference criteria at the temperature extremes of approximately 5 and 40 ºC. Two sondes met the USGS criteria for SC. One of the sondes failed the criteria for SC when evaluated in a 100,000-microsiemens-per-centimeter (μS/cm) standard at room temperature, and also failed in a 10,000-μS/cm standard at 5, 15, and 40 ºC. All three sondes met the USGS criteria for pH and DO at room temperature, but one sonde exceeded the allowable difference criteria when tested in pH 5.00 buffer and at 40 ºC. The USGS criteria and the technical specifications for turbidity were met by one sonde in standards ranging from 10 to 3,000 nephelometric turbidity units (NTU). A second sonde met the USGS criteria and the technical specifications except in the 3,000-NTU standard, and the third sonde exceeded the USGS calibration criteria in the 10- and 20-NTU standards and the technical specifications in the 20-NTU standard.Results of the field test showed acceptable performance and revealed that differences in data sample processing between sonde manufacturers may result in variances between the reported measurements when comparing one sonde to another. These variances in data would be more pronounced in dynamic site conditions. The lack of a wiper or other sensor-cleaning device on the DO sensor could prove problematic, and could limit the use of the HL4 to profiling applications or at sites with limited biofouling.

Planning Model for Health Careers Awareness: A Summer Program. Exemplary Project in Vocational Education, Conducted under Section 132 of Public Law 94-482. Final Report.

ERIC Educational Resources Information Center

Trident Technical Coll., Charleston, SC.

This program was designed to introduce high school students to the range of career opportunities available in the health field. Specific objectives were (1) to provide students with health careers information, (2) to allow students to explore career related topics with health professionals, (3) to give students an opportunity to spend at least…

Predicted Thermal Responses of Military Working Dog (MWD) to Chemical, Biological, Radiological, Nuclear (CBRN) Protective Kennel Enclosure

DTIC Science & Technology

2011-08-01

meteorological conditions. More specifically, climate chamber studies of the chemical protective kennel cover were conducted over a range of...responses to predict how long the dog could safely remain in the enclosure for various ambient environmental conditions. Climate chamber studies of...Engineering Center (NSRDEC) was tested in a climate - controlled chamber to quantify its insulation and vapor permeability properties. A schematic of

COMPLEX RUTHENIUM ACIDO-NITROS COMPOUNDS (in Russian)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zvyagintsev, O.E.; Starostin, S.M.

1961-06-01

The chemical nature of the water in the complex ruthenium acidonitroso compounds is studied by measuring certain acid properties, reactions, and behaviors of the compounds in aqueous solution. The dependence of molecular electrical conductivity on time and dilution, variations of specific electroconductivity, the optical density, and the light absorption of the compounds at 200 to 800 m mu wave range were investigated and the dissociation constants were calculated. (R.V.J.)

A Review of Strategic Mobility Models and Analysis

DTIC Science & Technology

1991-01-01

Logistics Directorate of the Joint Staff, (JS-J-4) specifically by the Studies , Concepts, and Analysis Division (SCAD), which conducts long-range...their analysis objec- tives. This study was designed to assist the Logistics Directorate of the Joint Staff (JS/J-4) to understand and improve the...This study concentrated on resource planning, which is the type of planning performed by the Logistics Directorate’s Studies , Concepts, and Analysis

Helicopter mathematical models and control law development for handling qualities research

NASA Technical Reports Server (NTRS)

Chen, Robert T. N.; Lebacqz, J. Victor; Aiken, Edwin W.; Tischler, Mark B.

1988-01-01

Progress made in joint NASA/Army research concerning rotorcraft flight-dynamics modeling, design methodologies for rotorcraft flight-control laws, and rotorcraft parameter identification is reviewed. Research into these interactive disciplines is needed to develop the analytical tools necessary to conduct flying qualities investigations using both the ground-based and in-flight simulators, and to permit an efficient means of performing flight test evaluation of rotorcraft flying qualities for specification compliance. The need for the research is particularly acute for rotorcraft because of their mathematical complexity, high order dynamic characteristics, and demanding mission requirements. The research in rotorcraft flight-dynamics modeling is pursued along two general directions: generic nonlinear models and nonlinear models for specific rotorcraft. In addition, linear models are generated that extend their utilization from 1-g flight to high-g maneuvers and expand their frequency range of validity for the design analysis of high-gain flight control systems. A variety of methods ranging from classical frequency-domain approaches to modern time-domain control methodology that are used in the design of rotorcraft flight control laws is reviewed. Also reviewed is a study conducted to investigate the design details associated with high-gain, digital flight control systems for combat rotorcraft. Parameter identification techniques developed for rotorcraft applications are reviewed.

Psychometric Properties and Clinical Usefulness of the Youth Self-Report DSM-Oriented Scales: A Field Study among Detained Male Adolescents

PubMed Central

Colins, Olivier F.

2016-01-01

It is unknown if the DSM-oriented (DSM) scales of the Youth Self-Report (YSR) are useful to determine what kind of narrowly-focused psychiatric assessment is needed, and how well these scales serve as a triage tool in real-world forensic settings. To address this knowledge gap, the YSR and diagnostic interviews were administered to 405 detained boys as part of a clinical protocol. Continuous DSM scale scores (e.g., Conduct Problems) were moderately to highly accurate in predicting their corresponding disorder (e.g., conduct disorder), whereas dichotomized DSM scale scores were not. To test the DSM scales’ usefulness for triage purposes, the sensitivity and specificity of being in the borderline range of one or more DSM scales were calculated. Almost all boys who did not have a disorder were in the normal range of at least one DSM scale (high specificity). However, many boys with a disorder would have been missed if such a decision rule was used for triage purposes (low sensitivity). In conclusion, their relations with the corresponding disorders support the construct validity of the DSM scales in an applied forensic setting. Nevertheless, the findings also warrant against the use of these scales for planning further narrowly-focused assessment or for triage purposes. PMID:27657102

Comprehensive Laboratory Evaluation of a Highly Specific Lateral Flow Assay for the Presumptive Identification of Bacillus anthracis Spores in Suspicious White Powders and Environmental Samples

PubMed Central

Ramage, Jason G.; Prentice, Kristin W.; DePalma, Lindsay; Venkateswaran, Kodumudi S.; Chivukula, Sruti; Chapman, Carol; Bell, Melissa; Datta, Shomik; Singh, Ajay; Hoffmaster, Alex; Sarwar, Jawad; Parameswaran, Nishanth; Joshi, Mrinmayi; Thirunavkkarasu, Nagarajan; Krishnan, Viswanathan; Morse, Stephen; Avila, Julie R.; Sharma, Shashi; Estacio, Peter L.; Stanker, Larry; Hodge, David R.

2016-01-01

We conducted a comprehensive, multiphase laboratory evaluation of the Anthrax BioThreat Alert® test strip, a lateral flow immunoassay (LFA) for the rapid detection of Bacillus anthracis spores. The study, conducted at 2 sites, evaluated this assay for the detection of spores from the Ames and Sterne strains of B. anthracis, as well as those from an additional 22 strains. Phylogenetic near neighbors, environmental background organisms, white powders, and environmental samples were also tested. The Anthrax LFA demonstrated a limit of detection of about 106 spores/mL (ca. 1.5 × 105 spores/assay). In this study, overall sensitivity of the LFA was 99.3%, and the specificity was 98.6%. The results indicated that the specificity, sensitivity, limit of detection, dynamic range, and repeatability of the assay support its use in the field for the purpose of qualitatively evaluating suspicious white powders and environmental samples for the presumptive presence of B. anthracis spores. PMID:27661796

The relationship between maternal self-efficacy and parenting practices: implications for parent training.

PubMed

Sanders, M R; Woolley, M L

2005-01-01

The present study examined the relationship between maternal self-efficacy, dysfunctional discipline practices and child conduct problems. Specifically, three levels of self-efficacy, global, domain and task-specific self-efficacy, were assessed in mothers of 2- to 8-year-old children with conduct problems (clinic group, n=45) and non-clinic mothers from the community (non-clinic group, n=79). Measures of global, domain and task-specific self-efficacy were completed by mothers. Clinic mothers reported significantly lower self-efficacy than non-clinic mothers for all but one of the parenting tasks assessed. Both groups of mothers reported lowest self-efficacy for similar parenting tasks. In the sample as a whole self-efficacy measures were significant predictors of maternal discipline style after controlling for other parent, child and risk factors. Of the self-efficacy variables behavioural self-efficacy was the best predictor of mothers discipline style. The findings support the importance of developing parenting strategies that enable parents to generalize their parenting skills to a diverse range of diverse parenting contexts both in the home and in the community.

Microzooplankton grazing and selective feeding during bloom periods in the Tolo Harbour area as revealed by HPLC pigment analysis

NASA Astrophysics Data System (ADS)

Liu, Xiangjiang; Tang, Chi Hung; Wong, Chong Kim

2014-07-01

Dilution experiments were conducted to investigate microzooplankton grazing impact on phytoplankton of different taxonomic groups and size fractions (< 5, 5-20, 20-200 μm) during spring and summer bloom periods at two different sites (inner Tolo Harbour and Tolo Channel) in the Tolo Harbour area, the northeastern coastal area of Hong Kong. Experiments combined with HPLC pigment analysis in three phytoplankton size fractions measured pigment and size specific phytoplankton growth rates and microzooplankton grazing rates. Pigment-specific phytoplankton growth rates ranged between 0.08 and 3.53 d- 1, while specific grazing rates of microzooplankton ranged between 0.07 and 2.82 d- 1. Highest specific rates of phytoplankton growth and microzooplankton grazing were both measured in fucoxanthin in 5-20 μm size fraction in inner Tolo Harbour in summer, which coincided with the occurrence of diatom bloom. Results showed significant correlations between phytoplankton growth and microzooplankton grazing rates. Microzooplankton placed high grazing pressure on phytoplankton community. High microzooplankton grazing impact on alloxanthin (2.63-5.13) suggested strong selection toward cryptophytes. Our results provided no evidence for size selective grazing on phytoplankton by microzooplankton.

The exit interview as a proxy measure of malaria case management practice: sensitivity and specificity relative to direct observation.

PubMed

Pulford, Justin; Siba, Peter M; Mueller, Ivo; Hetzel, Manuel W

2014-12-03

This paper aims to assess the sensitivity and specificity of exit interviews as a measure of malaria case management practice as compared to direct observation. The malaria case management of 1654 febrile patients attending 110 health facilities from across Papua New Guinea was directly observed by a trained research officer as part of a repeat cross sectional survey. Patient recall of 5 forms of clinical advice and 5 forms of clinical action were then assessed at service exit and statistical analyses on matched observation/exit interview data conducted. The sensitivity of exit interviews with respect to clinical advice ranged from 36.2% to 96.4% and specificity from 53.5% to 98.6%. With respect to clinical actions, sensitivity of the exit interviews ranged from 83.9% to 98.3% and specificity from 70.6% to 98.1%. The exit interview appears to be a valid measure of objective malaria case management practices such as the completion of a diagnostic test or the provision of antimalarial medication, but may be a less valid measure of low frequency, subjective practices such as the provision of malaria prevention advice.

Evaluation of Xylem EXO water-quality sondes and sensors

USGS Publications Warehouse

Snazelle, Teri T.

2015-01-01

Two models of multiparameter sondes manufactured by Xylem, parent company of Yellow Springs Incorporated (YSI)—EXO1 and EXO2—equipped with EXO conductivity/temperature (C/T), pH, dissolved oxygen (DO), and turbidity sensors, were evaluated by the U.S. Geological Survey (USGS) Hydrologic Instrumentation Facility. The sondes and sensors were evaluated in two phases for compliance with the manufacturer’s specifications and the USGS acceptance criteria for continuous water-quality monitors. Phase one tested the accuracy of the water-quality sondes equipped: (a) with a C/T, pH, DO, and turbidity sensor by comparing the EXO sensors’ measured values to those of an equivalently configured YSI 6920 V2-2 sensor, and (b) with multiple sensors of the same parameter type (such as three pH sensors and a C/T sensor) on a single sonde at room temperature and at an extended temperature range. In addition to accuracy, the communication protocols and the manufacturing specifications for range of detection and operating temperature were also tested during this phase. Phase two evaluated the sondes’ performance in a surface-water environment by deploying an EXO1 and an EXO2 equipped with pH, C/T, DO, and turbidity sensors at USGS site 02492620 located at East Pearl River near Bay Saint Louis, Mississippi. The EXO sondes’ temperature deviations from a certified YSI 4600 digital thermometer were within the ±0.2 degree Celsius (°C) USGS criteria, but were greater than the ±0.01 °C manufacturing specification. The conductivity sensors met the ±3 percent USGS criteria for specific conductance greater than 100 microsiemens per centimeter. The sensors met the more stringent ±0.5 percent manufacturing specification only at room temperature in the 250 microsiemens per centimeter (µS/cm) standard. The manufacturing and USGS criteria (±0.2 pH unit) were met in pH standards 4, 9.2, 10, and 12.45, but were not met in pH 1.68 standard. The DO sensors met both the ±0.3 milligram per liter (mg/L) USGS criteria and the ±1 percent manufacturing specification. The ±5 percent USGS criteria for turbidity in waters not exceeding 2,000 formazin nephelometric units (FNU) were met by the five turbidity sensors tested; however, all five sensors failed to meet these requirements at turbidities exceeding 2,000 FNU. The more stringent ±2 percent manufacturing turbidity specification for water with less than 1,000 FNU was met by only one of the five sensors tested. The results from the field deployment indicated acceptable agreement in temperature, specific conductance, pH, and DO between the EXO sondes, the site sonde, and the reference sonde. The EXO1 and EXO2 turbidity measurements differed from the site sonde by approximately 23 and 25 percent, respectively.

Electrical conductivity of aluminum hydride AlH3 at high pressure and temperature

NASA Astrophysics Data System (ADS)

Shakhray, Denis; Molodets, Alexander; Fortov, Vladimir; Khrapak, Aleksei

2009-06-01

A study of electrophysical and thermodynamic properties of alane AlH3 under multi shock compression has been carried out. The increase in specific electroconductivity of alane at shock compression up to pressure 100 GPa have been measured. High pressures and temperatures were obtained with explosive device, which accelerates the stainless impactor up to 3 km/sec. The impact shock is split into a shock wave reverberating in alane between two stiff metal anvils. The conductivity of shocked alane increases in the range up to 60-75 GPa and is about 30 1/Ohm*cm. In this region the semiconductor regime is true for shocked alane. The conductivity of alane achieves approximately 500 1/Ohm*cm at 80-90 GPa. In this region conductivity is interpreted in frames of the conception of the ``dielectric catastrophe'', taking into consideration significant difference between electronic states of isolated AlH3 molecule and condensed alane.

Streamflow, water quality, and aquatic macroinvertebrates of selected streams in Fairfax County, Virginia, 2007-12

USGS Publications Warehouse

Jastram, John D.

2014-01-01

Efforts to mitigate the effects of urbanization on streams rely on best management practices (BMPs) that are implemented with the intent of reducing and retaining stormwater runoff. A cooperative monitoring effort between the U.S. Geological Survey and Fairfax County, Virginia, was initiated in 2007 to assess the condition of county streams and document watershed-scale responses to the implementation of BMPs. Assessment of the data collected during the first 5 years of this monitoring program focused on characterizing the hydrologic and ecological condition of 14 monitored streams. Hydrologic, chemical, and macroinvertebrate community conditions in the streams monitored were found to be consistent, overall, with conditions commonly observed in urban streams. Hydrologically, the monitored streams were found to be flashy, with flashiness positively related to road cover in the watershed. Typical pH values of streams throughout the network centered around neutrality (pH = 7) with strong daily fluctuations apparent in the continuous data. Patterns in specific conductance were largely representative of anthropogenic disturbances—watersheds having the greatest percentage of open space and estate residential land-use had the lowest typical specific conductance values, and specific conductance variability was less than what is observed in watersheds that are more intensively developed. In watersheds having greater road coverage, and more development in general, increases in specific conductance over several orders of magnitude were observed during winter months as a result of the application of de-icing salts on impervious surfaces. Dissolved oxygen conditions were typically within the range required to support healthy biological communities, although occasional departures during summer months at some sites fell below the impairment threshold for streams in Virginia. Nitrogen (N) and phosphorus (P), concentration patterns were largely consistent across the network, with few exceptions. Nitrogen concentrations in monthly samples were generally low and dominated by nitrate. Exceptions to the generally low N concentrations occurred at Captain Hickory Run, which had a median total N concentration of approximately 4.9 milligrams per liter (mg/L), compared to the network-wide median of approximately 1.7 mg/L, and at Popes Head Creek Tributary, where total N concentrations spiked to 6–8 mg/L during low-flow periods in August or September of each year. Phosphorus concentrations in monthly samples were generally low and dominated by the dissolved fraction. Two monitoring stations in the network, Flatlick Branch and Frog Branch, are notable for having median total P concentrations that were, on average, approximately three times greater than the median total P concentration of 0.02 mg/L observed at the other 12 stations in the network. Suspended-sediment and nutrient loads and yields were similar to those of urbanized watersheds in other studies, although the yields from these urbanized basins were greater than, or within, the upper quartile of yields observed throughout the Chesapeake Bay watershed. Annual suspended-sediment loads ranged from 289–10,275 tons, with a median of 1,311 tons, and corresponding yields ranged from 107–2,827 tons per square mile (ton/mi2), with a median of 277 ton/mi2. Annual total N loads ranged from 8,014–36,413 pounds, with a median of 21,314 pounds, and corresponding yields ranged from 3,361–8,360 pounds per square mile (lb/mi2), with a median of 6,200 lb/mi2. Annual total P loads ranged from 380–6,558 pounds, with a median of 1,874 pounds, and corresponding yields ranged from 140–1,562 lb/mi2, with a median of 543 lb/mi2. Benthic macroinvertebrate community metrics indicated that streams throughout Fairfax County are generally of poor health. One station, Castle Creek, was an exception with results indicating relatively high quality aquatic health. Six additional monitoring stations were added to the network in 2012 to improve spatial coverage throughout Fairfax County. Monitoring activities are expected to continue at all 20 stations for the foreseeable future as BMP implementation is conducted.

Record-high specific conductance and water temperature in San Francisco Bay during water year 2015

USGS Publications Warehouse

Work, Paul A.; Downing-Kunz, Maureen; Livsey, Daniel N.

2017-02-22

The San Francisco estuary is commonly defined to include San Francisco Bay (bay) and the adjacent Sacramento–San Joaquin River Delta (delta). The U.S. Geological Survey (USGS) has operated a high-frequency (15-minute sampling interval) water-quality monitoring network in San Francisco Bay since the late 1980s (Buchanan and others, 2014). This network includes 19 stations at which sustained measurements have been made in the bay; currently, 8 stations are in operation (fig. 1). All eight stations are equipped with specific conductance (which can be related to salinity) and water-temperature sensors. Water quality in the bay constantly changes as ocean tides force seawater in and out of the bay, and river inflows—the most significant coming from the delta—vary on time scales ranging from those associated with storms to multiyear droughts. This monitoring network was designed to observe and characterize some of these changes in the bay across space and over time. The data demonstrate a high degree of variability in both specific conductance and temperature at time scales from tidal to annual and also reveal longer-term changes that are likely to influence overall environmental health in the bay.In water year (WY) 2015 (October 1, 2014, through September 30, 2015), as in the preceding water year (Downing-Kunz and others, 2015), the high-frequency measurements revealed record-high values of specific conductance and water temperature at several stations during a period of reduced freshwater inflow from the delta and other tributaries because of persistent, severe drought conditions in California. This report briefly summarizes observations for WY 2015 and compares them to previous years that had different levels of freshwater inflow.

Theoretical Performance of Liquid Hydrogen with Liquid Oxygen as a Rocket Propellant

NASA Technical Reports Server (NTRS)

Gordon, Sanford; McBride, Bonnie J.

1959-01-01

Theoretical rocket performance for both equilibrium and frozen composition during expansion was calculated for the propellant combination liquid hydrogen and liquid oxygen at four chamber pressures (60, 150, 300, and 600 lb/sq in. abs) and a wide range of pressure ratios (1 to 4000) and oxidant-fuel ratios (1.190 to 39.683). Data are given to estimate performance parameters at chamber pressures other than those for which data are tabulated. The parameters included are specific impulse, specific impulse in vacuum, combustion-chamber temperature, nozzle-exit temperature, molecular weight, molecular-weight derivatives, characteristic velocity, coefficient of thrust, ratio of nozzle-exit area to throat area, specific heat at constant pressure, isentropic exponent, viscosity, thermal conductivity, Mach number, and equilibrium gas compositions.

Cold-tip off-state conduction loss of miniature Stirling cycle cryocoolers

NASA Technical Reports Server (NTRS)

Kotsubo, V.; Johnson, D. L.; Ross, R. G., Jr.

1991-01-01

For redundant miniature Stirling-cycle cryocoolers in space applications, the off-state heat conduction down the coldfinger of one cooler is a parasitic heat load on the other coolers. At JPL, a heat flow transducer specifically designed to measure this load has been developed, and measurements have been performed on the coldfinger of a British Aerospace 80 K Stirling cooler with the tip temperature ranging between 40 and 170 K. Measurements have also been made using a transient warmup technique, where the warmup rates of the coldtip under various applied heat loads are used to determine the static conduction load. There is a difference between the results of these two methods, and these differences are discussed with regard to the applicability of the transient warmup method to a nonoperating coldfinger.

Psychopathy, startle blink modulation, and electrodermal reactivity in twin men

PubMed Central

BENNING, STEPHEN D.; PATRICK, CHRISTOPHER J.; IACONO, WILLIAM G.

2008-01-01

Psychopathy is a personality disorder with interpersonal–emotional and antisocial deviance facets. This study investigated these facets of psychopathy prospectively using normal-range personality traits in a community sample of young adult men who completed a picture-viewing task that included startle blink and skin conductance measures, like tasks used to study psychopathy in incarcerated men. Consistent with prior research, scores on the interpersonal–emotional facet of psychopathy (“fearless dominance”) were associated with deficient fear-potentiated startle. Conversely, scores on the social deviance facet of psychopathy (“impulsive antisociality”) were associated with smaller overall skin conductance magnitudes. Participants high in fearless dominance also exhibited deficient skin conductance magnitudes specifically to aversive pictures. Findings encourage further investigation of psychopathy and its etiology in community samples. PMID:16364071

Preliminary assessment of chloride concentrations, loads, and yields in selected watersheds along the Interstate 95 corridor, southeastern Connecticut, 2008-09

USGS Publications Warehouse

Brown, Craig J.; Mullaney, John R.; Morrison, Jonathan; Mondazzi, Remo

2011-01-01

Water-quality conditions were assessed to evaluate potential effects of road-deicer applications on stream-water quality in four watersheds along Interstate 95 (I-95) in southeastern Connecticut from November 1, 2008, through September 30, 2009. This preliminary study is part of a four-year cooperative study by the U.S. Geological Survey (USGS), the Federal Highway Administration (FHWA), and the Connecticut Department of Transportation (ConnDOT). Streamflow and water quality were studied at four watersheds?Four Mile River, Oil Mill Brook, Stony Brook, and Jordan Brook. Water-quality samples were collected and specific conductance was measured continuously at paired water-quality monitoring sites upstream and downstream from I-95. Specific conductance values were related to chloride (Cl) concentrations to assist in determining the effects of road-deicing operations on the levels of Cl in the streams. Streamflow and water-quality data were compared with weather data and with the timing, amount, and composition of deicers applied to state highways. Grab samples were collected during winter stormwater-runoff events, such as winter storms or periods of rain or warm temperatures in which melting takes place, and periodically during the spring and summer. Cl concentrations at the eight water-quality monitoring sites were well below the U.S. Environmental Protection Agency (USEPA) recommended chronic and acute Cl toxicity criteria of 230 and 860 milligrams per liter (mg/L), respectively. Specific conductance and estimated Cl concentrations in streams, particularly at sites downstream from I-95, peaked during discharge events in the winter and early spring as a result of deicers applied to roads and washed off by stormwater or meltwater. During winter storms, deicing activities, or subsequent periods of melting, specific conductance and estimated Cl concentrations peaked as high as 703 microsiemens per centimeter (?S/cm) and 160 mg/L at the downstream sites. During most of the spring and summer, specific conductance and estimated Cl concentrations decreased during discharge events because the low-ionic strength of stormwater had a diluting effect on stream-water quality. However, peaks in specific conductance and estimated Cl concentrations at Jordan Brook and Stony Brook corresponded to peaks in streamflow well after winter snow or ice events; these delayed peaks in Cl concentration likely resulted from deicing salts that remained in melting snow piles and (or) that were flushed from soils and shallow groundwater, then discharged downstream. Cl loads in streams generally were highest in the winter and early spring. The estimated load for the period of record at the four monitoring sites downstream from I-95 ranged from 0.33 ton per day (ton/d) at the Stony Brook watershed to 0.59 ton/d at the Jordan Brook watershed. The Cl yields ranged from 0.07 ton per day per square mile (ton/d/)mi2) at Oil Mill Brook, one of the least developed watersheds, to 0.21 (ton/d)/mi2) at Jordan Brook, the watershed with the highest percentage of urban development and impervious surfaces. The median estimates of Cl load from atmospheric deposition ranged from 11 to 19 tons, and contributed 4.3 to 7.1 percent of the Cl load in streamflow from the watershed areas. A comparison of the Cl load input and output estimates indicates that less Cl is leaving the watersheds than is entering through atmospheric deposition and application of deicers. The lag time between introduction of Cl to the watershed and transport to the stream, and uncertainty in the load estimates may be the reasons for this discrepancy. In addition, estimates of direct infiltration of Cl to groundwater from atmospheric deposition, deicer applications, and septic-tank drainfields to groundwater were outside the scope of the November 2008 to September 2009 assessment. However, increased concentrations of ions were observed between upstream and downstream sites and could result from deicer appli

Pre-placement screenings: An exploratory study of their use in a sample of New South Wales workplaces.

PubMed

McHugh, Cate; Gibson, Libby

2011-01-01

To conduct an exploratory pilot study of pre-placement screening practice in Australia by examining the nature and use of pre-placement screenings in a sample of New South Wales (NSW) workplaces. 29 of 279 employers (10.3%) invited using three sources: a public list of self-insured NSW companies, a regional chamber of commerce group and researcher's contacts. The majority of respondents (31%) belonged to government administration and education. Half of the workplaces employed more than 200 people. Employers completed an online survey from a link sent by email. Sixteen (55%) of the companies had a formal process for conducting pre-placement screenings, that were conducted by a range of professionals using a variety of methods, with costs ranging from $80 to $350 (Aus). The majority of respondents (81%) reported that the pre-placement screenings included an assessment of the person's ability to perform the specific physical demands of the job, i.e. against the specified physical demands of the position. The majority of employers who completed screenings found them useful. The findings, while from a small sample size, provide evidence that pre-placement screenings are being conducted in Australian workplaces by various professionals, using varying methods and are valued by employers.

Cold air performance of a tip turbine designed to drive a lift fan. 2: Partial admission

NASA Technical Reports Server (NTRS)

Haas, J. E.; Kofskey, M. G.; Hotz, G. M.; Futral, S. M., Jr.

1977-01-01

Partial admission performance was obtained for a 0.4 linear scale version of the LF460 lift fan turbine over a range of speed from 40 to 140 percent of design equivalent speed and a range of scroll inlet total to diffuser exit static pressure ratio from 2.2 to 5.0. The investigation was conducted in two parts, with each part using a different side of the turbine scroll to simulate loss of a gas generator. Each side had an arc of admission of 180. Results are presented in terms of specific work, torque, mass flow, and efficiency.

A Geochemical Mass-Balance Method for Base-Flow Separation, Upper Hillsborough River Watershed, West-Central Florida, 2003-2005 and 2009

USGS Publications Warehouse

Kish, G.R.; Stringer, C.E.; Stewart, M.T.; Rains, M.C.; Torres, A.E.

2010-01-01

Geochemical mass-balance (GMB) and conductivity mass-balance (CMB) methods for hydrograph separation were used to determine the contribution of base flow to total stormflow at two sites in the upper Hillsborough River watershed in west-central Florida from 2003-2005 and at one site in 2009. The chemical and isotopic composition of streamflow and precipitation was measured during selected local and frontal low- and high-intensity storm events and compared to the geochemical and isotopic composition of groundwater. Input for the GMB method included cation, anion, and stable isotope concentrations of surface water and groundwater, whereas input for the CMB method included continuous or point-sample measurement of specific conductance. The surface water is a calcium-bicarbonate type water, which closely resembles groundwater geochemically, indicating that much of the surface water in the upper Hillsborough River basin is derived from local groundwater discharge. This discharge into the Hillsborough River at State Road 39 and at Hillsborough River State Park becomes diluted by precipitation and runoff during the wet season, but retains the calcium-bicarbonate characteristics of Upper Floridan aquifer water. Field conditions limited the application of the GMB method to low-intensity storms but the CMB method was applied to both low-intensity and high-intensity storms. The average contribution of base flow to total discharge for all storms ranged from 31 to 100 percent, whereas the contribution of base flow to total discharge during peak discharge periods ranged from less than 10 percent to 100 percent. Although calcium, magnesium, and silica were consistent markers of Upper Floridan aquifer chemistry, their use in calculating base flow by the GMB method was limited because the frequency of point data collected in this study was not sufficient to capture the complete hydrograph from pre-event base-flow to post-event base-flow concentrations. In this study, pre-event water represented somewhat diluted groundwater. Streamflow conductivity integrates the concentrations of the major ions, and the logistics of acquiring specific conductance at frequent time intervals are less complicated than data collection, sample processing, shipment, and analysis of water samples in a laboratory. The acquisition of continuous specific conductance data reduces uncertainty associated with less-frequently collected geochemical point data.

Quality of water in James Creek, Monroe County, Mississippi

USGS Publications Warehouse

Bednar, G.A.

1981-01-01

A short-term quality-of-water study of James Creek near Aberdeen , Mississippi was conducted on November 14-16, 1978, during a period of low streamflow. During the study, the water in the 2.6-mile stream reach was undesireable for many uses. Wastewater inflow immediately upstream of the study area contributed to the dissolved-solids load in James Creek. The specific conductance of the water ranged from 775 to 890 micromhos at the head of the study reach and from 650 to 750 micromhos at the end of the study reach. A substantial biochemical oxygen-demand was evident in James Creek. Five-day biochemical oxygen demand values downstream of a sewage disposal pond outfall ranged from 8.3 to 11 milligrams per liter and dissolved-oxygen concentrations ranged from 0.4 to 4.5 milligrams per liter. Nitrogen and phosphorus compounds and fecal bacteria densities were highest downstream. Total ammonia nitrogen and phosphorus concentrations in the water leaving the study area ranged from 0.29 to 1.4 milligrams per liter and from 0.65 to 1.7 milligrams per liter, respectively. Fecal coliform densities exceeding 50,000 colonies per 100 milliliters of sample were observed in the study area. The median fecal coliform density of the water leaving the study area was 2,800 colonies per 100 milliliters. (USGS)

Lithology, hydraulic properties, and water quality of the Sandstone Aquifer in the northwestern part of the Bad River Indian Reservation, Wisconsin, 1998-1999

USGS Publications Warehouse

Dunning, Charles P.

2005-01-01

The Precambrian sandstone aquifer in the northwestern part of the Bad River Band of Lake Superior Tribe of Chippewa Indians Reservation, Ashland County, Wisconsin, provides much of the drinking water to area residents. A study was undertaken in cooperation with the Bad River Tribe to provide specific information about the lithology, hydraulic properties, and water quality of the sandstone aquifer. During 1998 and 1999, the U.S. Geological Survey installed three monitoring wells, collected and analyzed lithologic and water samples, and conducted geophysical logging and aquifer tests to characterize the sandstone aquifer. The two monitoring wells in the southeastern part of the study area, the Diaperville Monitoring Well #1 (Diaperville MW #1) and the Tolman Monitoring Well #1 (Tolman MW #1) , are believed to have encountered older Middle Proterozoic Oronto Group sandstones. The sandstone encountered in the Ackley Monitoring Well #1 (Ackley MW #1) is believed to be Chequamegon Sandstone of the Late Proterozoic Bayfield Group. This interpretation is based on previous studies, as well as thin- section analysis of sandstone core recovered from the Ackley Monitoring Well #1. Results of aquifer tests conducted in the Diaperville Monitoring Well #1 and the Tolman Monitoring Well #1 provide ranges for hydraulic param - eter values in the sandstone aquifer: transmissivity ranges from 83 to 509 square feet per day; hydraulic conductivity ranges from 1.6 to 4.5 feet per day; storativity ranges from 0.00019 to 0.00046; and specific capacity ranges from 0.22 to 0.67 gallons per minute per foot. Though high- and low-angle fractures are present in Ackley Monitoring Well #1 core, the hydraulic properties of the bedrock appear to be due largely to the matrix porosity measured in thin section (16–21 percent) and permeability of the sandstone. The aquifer test for the Diaperville Monitoring Well #1 resulted in observed drawdown in nearby glacial wells, evidence of a hydraulic connection between the sandstone aquifer and the glacial deposits. Major ion analyses indicate that the water sampled from the sandstone aquifer at the Ackley site is of the calcium-magnesium-sodium- bicarbonate type. Based on a single sampling set, volatile organic constituents were not detected in water samples from the Diaperville Monitoring Well #1 or the Ackley Monitoring Well #1. 

Genetic variability for stomatal conductance in Pima cotton and its relation to improvements of heat adaptation.

PubMed Central

Radin, J W; Lu, Z; Percy, R G; Zeiger, E

1994-01-01

Responses of stomata to environment have been intensively studied, but little is known of genetic effects on stomatal conductance or their consequences. In Pima cotton (Gossypium barbadense L.), a crop that is bred for irrigated production in very hot environments, stomatal conductance varies genetically over a wide range and has increased with each release of new higher-yielding cultivars. A cross between heat-adapted (high-yielding) and unadapted genotypes produced F2 progeny cosegregating for stomatal conductance and leaf temperature. Within segregating populations in the field, conductance was negatively correlated with foliar temperature because of evaporative cooling. Plants were selected from the F2 generation specifically and solely for differing stomatal conductance. Among F3 and F4 populations derived from these selections, conductance and leaf cooling were significantly correlated with fruiting prolificacy during the hottest period of the year and with yield. Conductance was not associated with other factors that might have affected yield potential (single-leaf photosynthetic rate, leaf water potential). As breeders have increased the yield of this crop, genetic variability for conductance has allowed inadvertent selection for "heat avoidance" (evaporative cooling) in a hot environment. PMID:11607487

Electrical, thermal and electrochemical properties of disordered carbon prepared from palygorskite and cane molasses

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alvarez, Edelio Danguillecourt, E-mail: edelioalvarez42@gmail.com; Laffita, Yodalgis Mosqueda, E-mail: yodalgis@imre.uh.cu; Montoro, Luciano Andrey, E-mail: landrey.montoro@gmail.com

We have synthesized and electrochemically tested a carbon sample that was suitable as anode for lithium secondary battery. The synthesis was based on the use of the palygorskite clay as template and sugar cane molasses as carbon source. X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, Brunauer–Emmett–Teller (BET) measurements and High Resolution Transmission Electron Microscope (HRTEM) analysis showed that the nanometric carbon material has a highly disordered graphene-like wrinkled structure and large specific surface area (467 m{sup 2} g{sup −1}). The compositional characterization revealed a 14% of heteroatoms-containing groups (O, H, N, S) doping the as-prepared carbon. Thermophysicalmore » measurements revealed the good thermal stability and an acceptable thermal diffusivity (9·10{sup −7} m{sup 2} s{sup −1}) and conductivity (1.1 W m{sup −1} K{sup −1}) of this carbon. The electrical properties showed an electronic conductivity of hole-like carriers of approximately one S/cm in a 173–293 K range. The testing of this material as anodes in a secondary lithium battery displayed a high specific capacity and excellent performance in terms of number of cycles. A high reversible capacity of 356 mA h g{sup −1} was reached. - Graphical abstract: TEM image and electrochemistry behavior of a new graphene oxide-like carbon. - Highlights: • A high disordered graphene oxide-like conducting carbon is reported. • The synthesis was based on palygorskite and sugar cane molasses as precursors. • The disordered conducting carbon is composed of doped- graphene heterogeneous domains. • This material combines a large specific surface area and high electric conductivity. • The thermophysical and electrochemical properties of this material reveal adequate behavior.« less

Help in the Choice of Automated or Semiautomated Immunoassays for Serological Diagnosis of Toxoplasmosis: Evaluation of Nine Immunoassays by the French National Reference Center for Toxoplasmosis.

PubMed

Villard, O; Cimon, B; L'Ollivier, C; Fricker-Hidalgo, H; Godineau, N; Houze, S; Paris, L; Pelloux, H; Villena, I; Candolfi, E

2016-12-01

Toxoplasmosis, a benign infection, is asymptomatic or paucisymptomatic in over 80% of cases, except in immunocompetent patients suffering from ocular toxoplasmosis or in immunocompromised patients with opportunistic or congenital toxoplasmosis. Diagnosis is based mainly on serology testing. Thus, we compared the performance of the nine most commonly used commercial automated or semiautomated immunoassays for IgG and IgM Toxoplasma gondii antibody detection, that is, the Advia Centaur, Architect, AxSYM, Elecsys, Enzygnost, Liaison, Platelia, VIDAS, and VIDIA assays. The assays were conducted on four panels of serum samples derived during routine testing from patients with an interfering disease and who exhibited a low IgG antibody level in one of two clinical settings, namely, acute or chronic toxoplasmosis. As a result, IgG sensitivities ranged from 97.1% to 100%, and IgG specificities ranged from 99.5% to 100%. For IgG quantification, strong differences in IgG titers (expressed in IU/ml) were noted depending on the assay used. IgM sensitivities ranged from 65% to 97.9%, and IgM specificities ranged from 92.6% to 100%. For defining the best serological strategies to be implemented, it appears crucial to compare the diagnostic performance of the different tests with respect to their specificity and sensitivity in detecting the presence of IgG and IgM antibodies. Copyright © 2016, American Society for Microbiology. All Rights Reserved.

Help in the Choice of Automated or Semiautomated Immunoassays for Serological Diagnosis of Toxoplasmosis: Evaluation of Nine Immunoassays by the French National Reference Center for Toxoplasmosis

PubMed Central

Cimon, B.; L'Ollivier, C.; Fricker-Hidalgo, H.; Godineau, N.; Houze, S.; Paris, L.; Pelloux, H.; Villena, I.

2016-01-01

Toxoplasmosis, a benign infection, is asymptomatic or paucisymptomatic in over 80% of cases, except in immunocompetent patients suffering from ocular toxoplasmosis or in immunocompromised patients with opportunistic or congenital toxoplasmosis. Diagnosis is based mainly on serology testing. Thus, we compared the performance of the nine most commonly used commercial automated or semiautomated immunoassays for IgG and IgM Toxoplasma gondii antibody detection, that is, the Advia Centaur, Architect, AxSYM, Elecsys, Enzygnost, Liaison, Platelia, VIDAS, and VIDIA assays. The assays were conducted on four panels of serum samples derived during routine testing from patients with an interfering disease and who exhibited a low IgG antibody level in one of two clinical settings, namely, acute or chronic toxoplasmosis. As a result, IgG sensitivities ranged from 97.1% to 100%, and IgG specificities ranged from 99.5% to 100%. For IgG quantification, strong differences in IgG titers (expressed in IU/ml) were noted depending on the assay used. IgM sensitivities ranged from 65% to 97.9%, and IgM specificities ranged from 92.6% to 100%. For defining the best serological strategies to be implemented, it appears crucial to compare the diagnostic performance of the different tests with respect to their specificity and sensitivity in detecting the presence of IgG and IgM antibodies. PMID:27733631

Can CT imaging features of ground-glass opacity predict invasiveness? A meta-analysis.

PubMed

Dai, Jian; Yu, Guoyou; Yu, Jianqiang

2018-04-01

A meta-analysis was conducted to investigate the diagnostic performance of computed tomography (CT) imaging features of ground-glass opacity (GGO) to predict invasiveness. Two reviewers independently searched PubMed, Medline, Web of Science, Cochrane Embase and CNKI for relevant studies. CT imaging signs of bubble lucency, speculation, lobulated margin, and pleural indentation were used as diagnostic references to discriminate pre-invasive and invasive disease. The sensitivity, specificity, diagnostic odds ratio (DOR), summary receiver operating characteristic (SROC) curves, and the area under the SROC curve (AUC) were calculated to evaluate diagnostic efficiency. Twelve studies were finally included. Diagnostic performance ranged from 0.41 to 0.52 for sensitivity and 0.56 to 0.63 for specificity. The diagnostic positive and negative likelihood ratios ranged from 1.03 to 2.13 and 0.52 to 1.05, respectively. The DORs of the GGO CT features for discriminating invasive disease ranged from 1.02 to 4.00. The area under the ROC curve was also low, with a range of 0.60 to 0.67 for discriminating pre-invasive and invasive disease. The diagnostic value of a single CT imaging sign of GGO, such as bubble lucency, speculation, lobulated margin, or pleural indentation is limited for discriminating pre-invasive and invasive disease because of low sensitivity, specificity, and AUC. © 2018 The Authors. Thoracic Cancer published by China Lung Oncology Group and John Wiley & Sons Australia, Ltd.

Altitude-chamber performance of British Rolls-Royce Nene II engine III : 18.00-inch-diameter jet nozzle

NASA Technical Reports Server (NTRS)

Grey, Ralph E; Brightwell, Virginia L; Barson, Zelmar; NACA

1950-01-01

An altitude-chamber investigation of British Rolls-Royce Nene II turbojet engine was conducted over range of altitudes from sea level to 65,000 feet and ram pressure ratios from 1.10 to 3.50, using an 18.00-inch-diameter jet nozzle. The 18.00-inch-diameter jet nozzle gave slightly lower values of net-thrust specific fuel consumption than either the 18.41- or the standard 18.75-inch-diameter jet nozzles at high flight speeds. At low flight speeds, the 18.41-inch-diameter jet nozzle gave the lowest value of net-thrust specific fuel consumption.

Space tug thermal control. [design criteria and specifications

NASA Technical Reports Server (NTRS)

1974-01-01

It was determined that space tug will require the capability to perform its mission within a broad range of thermal environments with currently planned mission durations of up to seven days, so an investigation was conducted to define a thermal design for the forward and intertank compartments and fuel cell heat rejection system that satisfies tug requirements for low inclination geosynchronous deploy and retrieve missions. Passive concepts were demonstrated analytically for both the forward and intertank compartments, and a worst case external heating environment was determined for use during the study. The thermal control system specifications and designs which resulted from the research are shown.

The Quality of Water and Bottom Material in Lunga Reservoir, Virginia, September 2004 through August 2005

USGS Publications Warehouse

Lotspeich, R. Russell

2007-01-01

Lunga Reservoir is on the U.S. Marine Corps Base in Quantico, which is in the Potomac River basin and the Piedmont Physiographic Province of northern Virginia. Because of the potential use of the reservoir for scuba-diver training and public water supply in addition to current recreational activities, the U.S. Marine Corps wanted to know more about the water quality of Lunga Reservoir and how it compared to Virginia Department of Environmental Quality and Virginia State Water Control Board ambient water-quality standards. Water samples and physical properties were collected by the U.S. Geological Survey at 6 locations throughout Lunga Reservoir, and physical properties were collected at 11 additional locations in the reservoir from September 2004 through August 2005. Water samples for analysis of pesticides and bottom-material trace elements were collected once during the study at four of the sampling locations. Water temperature, dissolved-oxygen concentration, specific conductance, pH, and total chlorophyll concentration in Lunga Reservoir all had similar seasonal and spatial variations as in other lakes and reservoirs in this geographic region - thermal gradient in the summer and fall and isothermal conditions in the winter and early spring. Concentrations of water-quality indicators in Lunga Reservoir were within comparable levels of those in other reservoirs and did not violate the Virginia State Water Control Board standards for public water supplies. Water temperatures throughout Lunga Reservoir during the study period ranged from 4.4 to 30.1 degrees Celsius, well below the State Water Control Board maximum water temperature criteria of 32 degrees Celsius. Dissolved-oxygen concentrations ranged from 0.05 to 14.1 milligrams per liter throughout the reservoir during the study period, but never fell below the State Water Control Board minimum dissolved-oxygen criterion of 4.0 milligrams per liter at the surface of Lunga Reservoir. Specific conductance throughout Lunga Reservoir ranged from 29 to 173 microsiemens per centimeter at 25 degrees Celsius during the study period, with a mean specific conductance of 68 microsiemens per centimeter at 25 degrees Celsius. Measurements of pH throughout the reservoir ranged from 4.8 to 7.6 standard units. Concentrations of chemical constituents analyzed in Lunga Reservoir samples were below any State Water Control Board criteria and generally were similar in concentration to the same chemical constituents in other reservoirs in the State. Four water samples were analyzed for 54 pesticides, and none of these pesticides were above the laboratory minimum reporting level.

Surface vapor conductance derived from the ETRHEQ: Dependence on environmental variables and similarity to Oren's stomatal stress model for vapor pressure deficit

NASA Astrophysics Data System (ADS)

Salvucci, G.; Rigden, A. J.

2015-12-01

Daily time series of evapotranspiration and surface conductance to water vapor were estimated using the ETRHEQ method (Evapotranspiration from Relative Humidity at Equilibrium). ETRHEQ has been previously compared with ameriflux site-level measurements of ET at daily and seasonal time scales, with watershed water balance estimates, and with various benchmark ET data sets. The ETRHEQ method uses meteorological data collected at common weather stations and estimates the surface conductance by minimizing the vertical variance of the calculated relative humidity profile averaged over the day. The key advantage of the ETRHEQ method is that it does not require knowledge of the surface state (soil moisture, stomatal conductance, leaf are index, etc.) or site-specific calibration. The daily estimates of conductance from 229 weather stations for 53 years were analyzed for dependence on environmental variables known to impact stomatal conductance and soil diffusivity: surface temperature, surface vapor pressure deficit, solar radiation, antecedent precipitation (as a surrogate for soil moisture), and a seasonal vegetation greenness index. At each site the summertime (JJAS) conductance values estimated from ETRHEQ were fitted to a multiplicate Jarvis-type stress model. Functional dependence was not proscribed, but instead fitted using flexible piecewise-linear splines. The resulting stress functions reproduce the time series of conductance across a wide range of ecosystems and climates. The VPD stress term resembles that proposed by Oren (i.e., 1-m*log(VPD) ), with VPD measured in kilopascals. The equivalent value of m derived from our spline-fits at each station varied over a remarkably small range of 0.58 to 0.62, in agreement with Oren's original analysis based on leaf and tree-level measurements.

Compressed glassy carbon: An ultrastrong and elastic interpenetrating graphene network

PubMed Central

Hu, Meng; He, Julong; Zhao, Zhisheng; Strobel, Timothy A.; Hu, Wentao; Yu, Dongli; Sun, Hao; Liu, Lingyu; Li, Zihe; Ma, Mengdong; Kono, Yoshio; Shu, Jinfu; Mao, Ho-kwang; Fei, Yingwei; Shen, Guoyin; Wang, Yanbin; Juhl, Stephen J.; Huang, Jian Yu; Liu, Zhongyuan; Xu, Bo; Tian, Yongjun

2017-01-01

Carbon’s unique ability to have both sp2 and sp3 bonding states gives rise to a range of physical attributes, including excellent mechanical and electrical properties. We show that a series of lightweight, ultrastrong, hard, elastic, and conductive carbons are recovered after compressing sp2-hybridized glassy carbon at various temperatures. Compression induces the local buckling of graphene sheets through sp3 nodes to form interpenetrating graphene networks with long-range disorder and short-range order on the nanometer scale. The compressed glassy carbons have extraordinary specific compressive strengths—more than two times that of commonly used ceramics—and simultaneously exhibit robust elastic recovery in response to local deformations. This type of carbon is an optimal ultralight, ultrastrong material for a wide range of multifunctional applications, and the synthesis methodology demonstrates potential to access entirely new metastable materials with exceptional properties. PMID:28630918

Childhood mortality impact and costs of integrating vitamin A supplementation into immunization campaigns.

PubMed Central

Ching, P; Birmingham, M; Goodman, T; Sutter, R; Loevinsohn, B

2000-01-01

Country-specific activity and coverage data were used to estimate the childhood mortality impact (deaths averted) and costs of integrating vitamin A supplements into immunization campaigns conducted in 1998 and 1999. More than 94 million doses of vitamin A were administered in 41 countries in 1998, helping to avert nearly 169,000 deaths. During 1999, delivery of more than 97 million doses in 50 countries helped avert an estimated 242,000 deaths. The estimated incremental cost per death averted was US$72 (range: 36-142) in 1998 and US$64 (range: 32-126) in 1999. The estimated average total cost of providing supplementation per death averted was US$310 (range: 157-609) in 1998 and US$276 (range: 139-540) in 1999. Costs per death averted varied by campaign, depending on the number and proportion of the child population reached, number of doses received per child, and child mortality rates. PMID:11029982

An experimental study of phase transitions in a complex plasma

NASA Astrophysics Data System (ADS)

Smith, Bernard Albert Thomas, II

In semiconductor manufacturing, contamination due to particulates significantly decreases the yield and quality of device fabrication, therefore increasing the cost of production. Dust particle clouds can be found in almost all plasma processing environments including both plasma etching devices and in plasma deposition processes. Dust particles suspended within such plasmas will acquire an electric charge from collisions with free electrons in the plasma. If the ratio of inter-particle potential energy to the average kinetic energy is sufficient, the particles will form either a "liquid" structure with short range ordering or a crystalline structure with long range ordering. Otherwise, the dust particle system will remain in a gaseous state. Many experiments have been conducted over the past decade on such complex plasmas to discover the character of the systems formed, but more work is needed to fully understand these structures. This paper describes the processes involved in setting up the CASPER GEC RF Reference Cell and the modifications necessary to examine complex plasmas. Research conducted to characterize the system is outlined to demonstrate that the CASPER Cell behaves as other GEC Cells. In addition, further research performed shows the behavior of the complex plasma system in the CASPER Cell is similar to complex plasmas studied by other groups in this field. Along the way analysis routines developed specifically for this system are described. New research involving polydisperse dust distributions is carried out in the system once the initial characterization is finished. Next, a system to externally vary the DC bias in the CASPER Cell is developed and characterized. Finally, new research conducted to specifically examine how the complex plasma system reacts to a variable DC bias is reported. Specifically, the response of the interparticle spacing to various system parameters (including the external DC bias) is examined. Also, a previously unreported phenomenon, namely layer splitting, is examined.

Andreev current for low temperature thermometry

NASA Astrophysics Data System (ADS)

Faivre, T.; Golubev, D. S.; Pekola, J. P.

2015-05-01

We demonstrate experimentally that disorder enhanced Andreev current in a tunnel junction between a normal metal and a superconductor provides a method to measure electronic temperature, specifically at temperatures below 200 mK when aluminum is used. This Andreev thermometer has some advantages over conventional quasiparticle thermometers: For instance, it does not conduct heat and its reading does not saturate until at lower temperatures. Another merit is that the responsivity is constant over a wide temperature range.

Chemistry of selected high-elevation lakes in seven national parks in the western United States

USGS Publications Warehouse

Clow, David W.; Striegl, Robert G.; Nanus, Leora; Mast, M. Alisa; Campbell, Donald H.; Krabbenhoft, David P.

2002-01-01

A chemical survey of 69 high-altitude lakes in seven national parks in the western United States was conducted during the fallof 1999; the lakes were previously sampled during the fall of 1985, as part of the Western Lake Survey. Lakes in parks in the Sierra/southern Cascades (Lassen Volcanic, Yosemite, Sequoia/Kings Canyon National Parks) and in the southern RockyMountains (Rocky Mountain National Park) were very dilute; medianspecific conductance ranged from 4.4 to 12.2 μS cm-1 andmedian alkalinity concentrations ranged from 32.2 to 72.9 μeqL-1. Specific conductances and alkalinity concentrations were substantially higher in lakes in the central and northernRocky Mountains parks (Grand Teton, Yellowstone, and GlacierNational Parks), probably due to the prevalence of more reactivebedrock types. Regional patterns in lake concentrations of NO3 and SO4 were similar to regional patterns in NO3 and SO4 concentrations in precipitation, suggestingthat the lakes are showing a response to atmospheric deposition.Concentrations of NO3 were particularly high in Rocky Mountain National Park, where some ecosystems appear to be undergoing nitrogen saturation.

Low-temperature thermal properties of a hyperaged geological glass.

PubMed

Pérez-Castañeda, Tomás; Jiménez Riobóo, Rafael J; Ramos, Miguel A

2013-07-24

We have measured the specific heat of amber from the Dominican Republic, an ancient geological glass about 20 million years old, in the low-temperature range 0.6 K ≤ T ≤ 26 K, in order to assess the effects of its natural stabilization (hyperageing) process on the low-temperature glassy properties, i.e. boson peak and two-level systems. We have also conducted modulated differential scanning calorimetry experiments to characterize the thermodynamic state of our samples. We found that calorimetric curves exhibit a huge ageing signal ΔH ≈ 5 J g(-1) in the first upscan at the glass transition Tg = 389 K, that completely disappears after heating up (rejuvenating) the sample to T = 395 K for 3 h. To independently evaluate the phonon contribution to the specific heat, Brillouin spectroscopy was performed in the temperature range 80 K ≤ T ≤ 300 K. An expected increase in the Debye level was observed after rejuvenating the Dominican amber. However, no significant change was observed in the low-temperature specific heat of glassy amber after erasing its thermal history: both its boson peak (i.e., the maximum in the Cp/T(3) representation) and the density of tunnelling two-level systems (i.e., the Cp ∼ T contribution at the lowest temperatures) remained essentially the same. Also, a consistent analysis using the soft-potential model of our Cp data and earlier thermal-conductivity data found in the literature further supports our main conclusion, namely, that these glassy 'anomalous' properties at low temperatures remain essentially invariant after strong relaxational processes such as hyperageing.

WASP: A flexible FORTRAN 4 computer code for calculating water and steam properties

NASA Technical Reports Server (NTRS)

Hendricks, R. C.; Peller, I. C.; Baron, A. K.

1973-01-01

A FORTRAN 4 subprogram, WASP, was developed to calculate the thermodynamic and transport properties of water and steam. The temperature range is from the triple point to 1750 K, and the pressure range is from 0.1 to 100 MN/m2 (1 to 1000 bars) for the thermodynamic properties and to 50 MN/m2 (500 bars) for thermal conductivity and to 80 MN/m2 (800 bars) for viscosity. WASP accepts any two of pressure, temperature, and density as input conditions. In addition, pressure and either entropy or enthalpy are also allowable input variables. This flexibility is especially useful in cycle analysis. The properties available in any combination as output include temperature, density, pressure, entropy, enthalpy, specific heats, sonic velocity, viscosity, thermal conductivity, surface tension, and the Laplace constant. The subroutine structure is modular so that the user can choose only those subroutines necessary to his calculations. Metastable calculations can also be made by using WASP.

Nanospray mass spectrometry with indirect conductive graphite coating.

PubMed

Viberg, Peter; Nilsson, Staffan; Skog, Kerstin

2004-07-15

An easy and cost-effective method to manufacture a robust conductive graphite coating for nanospray mass spectrometry (nESI-MS) and capillary electrophoresis (CE)-nESI-MS is described. The method involves graphite coating of a tube sleeve, into which the nESI emitter is inserted and connected to a transfer capillary, instead of coating the actual emitter. The coating, made of graphite from a pencil and epoxy glue, was stable over long periods of use (>80 h) and showed excellent resistance toward various solvents. Stable electrospray was achieved in the investigated flow range (150-900 nL x min(-)(1)), and salbutamol, diphenhydramine, and nortriptyline (M(w): 239-263 g x mol(-)(1)) were detected in the nanomole per liter range during continuous pumping. CE-nESI-MS analysis gave excellent signal-to-noise ratios for 100-fmol injections. The technique allows simple exchange of the nESI emitter to suit a specific flow rate, and it minimizes risk of corona discharge.

ERTS: A multispectral image analysis contribution for the geomorphological evaluation of southern Maracaibo Lake Basin. [geological survey and drainage patterns

NASA Technical Reports Server (NTRS)

Salas, F.; Cabello, O.; Alarcon, F.; Ferrer, C.

1974-01-01

Multispectral analysis of ERTS-A images at scales of 1:1,000,000 and 1:500,000 has been conducted with conventional photointerpretation methods. Specific methods have been developed for the geomorphological analysis of southern Maracaibo Lake Basin which comprises part of the Venezuelan Andean Range, Perija Range, the Tachira gap and the Southern part of the Maracaibo Lake depression. A steplike analysis was conducted to separate macroforms, landscapes and relief units as well as drainage patterns and tectonic features, which permitted the delineation of tectonic provinces, stratigraphic units, geomorphologic units and geomorphologic positions. The geomorphologic synthesis obtained compares favorably with conventional analysis made on this area for accuracy of 1:100,000 scale, and in some features with details obtained through conventional analysis for accuracy of 1:15,000 and field work. Geomorphological units in the mountains were identified according to changes in tone, texture, forms orientation of interfluves and tectonic characteristics which control interfluvial disimetrics.

Electrolytic decontamination of conductive materials

NASA Astrophysics Data System (ADS)

Campbell, George M.; Nelson, Timothy O.; Parker, John L.; Getty, Richard H.; Hergert, Tom R.; Lindahl, Kirk A.; Peppers, Larry G.

1994-10-01

Using the electrolytic method, we have demonstrated removal of Pu and Am from contaminated conductive material. At EG and G /Rocky Flats, we electrolytically decontaminated stainless steel. Results from this work show removal of fixed contamination, including the following geometries: planar, large radius, bolt holes, glove ports, and protruding studs. More specifically, fixed contamination was reduced from levels ranging from greater than 1 000 000 counts per minute (cpm) down to levels ranging from 1500 to 250 cpm using the electrolytic method. More recently, the electrolytic work has continued at Los Alamos National Laboratory as a joint project with EG and G/Rocky Flats. Impressively, electrolytic decontamination of Pu /Am from U surfaces (10 sq cm per side) shows decreases in swipable contamination from 500 000-1 500 000 disintegrations per minute (dpm) down to 0-2 dpm. Moreover, the solid waste product of the electrolytic method is reduced in volume by more than 50 times compared with the liquid waste produced by the previous U decontamination method -- a hot concentrated acid spray leach process.

Exposure to lead in South African shooting ranges.

PubMed

Mathee, Angela; de Jager, Pieter; Naidoo, Shan; Naicker, Nisha

2017-02-01

Lead exposure in shooting ranges has been under scrutiny for decades, but no information in this regard is available in respect of African settings, and in South Africa specifically. The aim of this study was to determine the blood lead levels in the users of randomly selected private shooting ranges in South Africa's Gauteng province. An analytical cross sectional study was conducted, with participants recruited from four randomly selected shooting ranges and three archery ranges as a comparator group. A total of 118 (87 shooters and 31 archers) were included in the analysis. Shooters had significantly higher blood lead levels (BLL) compared to archers with 36/85 (42.4%) of shooters versus 2/34 (5.9%) of archers found to have a BLL ≥10μg/dl (p<0.001). Shooting ranges may constitute an import site of elevated exposure to lead. Improved ventilation, low levels of awareness of lead hazards, poor housekeeping, and inadequate personal hygiene facilities and practices at South African shooting ranges need urgent attention. Copyright © 2016 The Authors. Published by Elsevier Inc. All rights reserved.

Recent advances in polyaniline based biosensors.

PubMed

Dhand, Chetna; Das, Maumita; Datta, Monika; Malhotra, B D

2011-02-15

The present paper contains a detailed overview of recent advances relating to polyaniline (PANI) as a transducer material for biosensor applications. This conducting polymer provides enormous opportunities for binding biomolecules, tuning their bio-catalytic properties, rapid electron transfer and direct communication to produce a range of analytical signals and new analytical applications. Merging the specific nature of different biomolecules (enzymes, nucleic acids, antibodies, etc.) and the key properties of this modern conducting matrix, possible biosensor designs and their biosensing characteristics have been discussed. Efforts have been made to discuss and explore various characteristics of PANI responsible for direct electron transfer leading towards fabrication of mediator-less biosensors. Copyright © 2010 Elsevier B.V. All rights reserved.

Characterization of the mechanical and physical properties of TD-NiCr (Ni-20Cr-2ThO2) alloy sheet

NASA Technical Reports Server (NTRS)

Fritz, L. J.; Koster, W. P.; Taylor, R. E.

1973-01-01

Sheets of TD-NiCr processed using techniques developed to produce uniform material were tested to supply mechanical and physical property data. Two heats each of 0.025 and 0.051 cm thick sheet were tested. Mechanical properties evaluated included tensile, modulus of elasticity, Poisson's Ratio, compression, creep-rupture, creep strength, bearing strength, shear strength, sharp notch and fatigue strength. Test temperatures covered the range from ambient to 1589K. Physical properties were also studied as a function of temperature. The physical properties measured were thermal conductivity, linear thermal expansion, specific heat, total hemispherical emittance, thermal diffusivity, and electrical conductivity.

Special Test Methods for Batteries

NASA Technical Reports Server (NTRS)

Gross, S.

1984-01-01

Various methods are described for measuring heat generation in primary and secondary batteries as well as the specific heat of batteries and cell thermal conductance. Problems associated with determining heat generation in large batteries are examined. Special attention is given to monitoring temperature gradients in nickel cadmium cells, the use of auxiliary electrodes for conducting tests on battery charge control, evaluating the linear sweep of current from charge to discharge, and determining zero current voltage. The fast transient behavior of batteries in the microsecond range, and the electrical conductance of nickel sinters in the thickness direction are also considered. Mechanical problems experienced in the vibration of Ni-Cd batteries and tests to simulate cyclic fatigue of the steel table connecting the plates to the comb are considered. Methods of defining the distribution of forces when cells are compressed during battery packaging are also explored.

Special test methods for batteries

NASA Astrophysics Data System (ADS)

Gross, S.

1984-09-01

Various methods are described for measuring heat generation in primary and secondary batteries as well as the specific heat of batteries and cell thermal conductance. Problems associated with determining heat generation in large batteries are examined. Special attention is given to monitoring temperature gradients in nickel cadmium cells, the use of auxiliary electrodes for conducting tests on battery charge control, evaluating the linear sweep of current from charge to discharge, and determining zero current voltage. The fast transient behavior of batteries in the microsecond range, and the electrical conductance of nickel sinters in the thickness direction are also considered. Mechanical problems experienced in the vibration of Ni-Cd batteries and tests to simulate cyclic fatigue of the steel table connecting the plates to the comb are considered. Methods of defining the distribution of forces when cells are compressed during battery packaging are also explored.

A feasibility study for advanced technology integration for general aviation

NASA Technical Reports Server (NTRS)

Kohlman, D. L.; Matsuyama, G. T.; Hawley, K. E.; Meredith, P. T.

1980-01-01

An investigation was conducted to identify candidate technologies and specific developments which offer greatest promise for improving safety, fuel efficiency, performance, and utility of general aviation airplanes. Interviews were conducted with general aviation airframe and systems manufacturers and NASA research centers. The following technologies were evaluated for use in airplane design tradeoff studies conducted during the study: avionics, aerodynamics, configurations, structures, flight controls, and propulsion. Based on industry interviews and design tradeoff studies, several recommendations were made for further high payoff research. The most attractive technologies for use by the general aviation industry appear to be advanced engines, composite materials, natural laminar flow airfoils, and advanced integrated avionics systems. The integration of these technologies in airplane design can yield significant increases in speeds, ranges, and payloads over present aircraft with 40 percent to 50 percent reductions in fuel used.

Lightning protection for shuttle propulsion elements

NASA Technical Reports Server (NTRS)

Goodloe, Carolyn C.; Giudici, Robert J.

1991-01-01

The results of lightning protection analyses and tests are weighed against the present set of waivers to the NASA lightning protection specification. The significant analyses and tests are contrasted with the release of a new and more realistic lightning protection specification, in September 1990, that resulted in an inordinate number of waivers. A variety of lightning protection analyses and tests of the Shuttle propulsion elements, the Solid Rocket Booster, the External Tank, and the Space Shuttle Main Engine, were conducted. These tests range from the sensitivity of solid propellant during shipping to penetration of cryogenic tanks during flight. The Shuttle propulsion elements have the capability to survive certain levels of lightning strikes at certain times during transportation, launch site operations, and flight. Changes are being evaluated that may improve the odds of withstanding a major lightning strike. The Solid Rocket Booster is the most likely propulsion element to survive if systems tunnel bond straps are improved. Wiring improvements were already incorporated and major protection tests were conducted. The External Tank remains vulnerable to burn-through penetration of its skin. Proposed design improvements include the use of a composite nose cone and conductive or laminated thermal protection system coatings.

Small Launch Vehicle Concept Development for Affordable Multi-Stage Inline Configurations

NASA Technical Reports Server (NTRS)

Beers, Benjamin R.; Waters, Eric D.; Philips, Alan D.; Threet, Grady E., Jr.

2014-01-01

The Advanced Concepts Office at NASA's George C. Marshall Space Flight Center conducted a study of two configurations of a three-stage, inline, liquid propellant small launch vehicle concept developed on the premise of maximizing affordability by targeting a specific payload capability range based on current and future industry demand. The initial configuration, NESC-1, employed liquid oxygen as the oxidizer and rocket propellant grade kerosene as the fuel in all three stages. The second and more heavily studied configuration, NESC-4, employed liquid oxygen and rocket propellant grade kerosene on the first and second stages and liquid oxygen and liquid methane fuel on the third stage. On both vehicles, sensitivity studies were first conducted on specific impulse and stage propellant mass fraction in order to baseline gear ratios and drive the focus of concept development. Subsequent sensitivity and trade studies on the NESC-4 concept investigated potential impacts to affordability due to changes in gross liftoff mass and/or vehicle complexity. Results are discussed at a high level to understand the impact severity of certain sensitivities and how those trade studies conducted can either affect cost, performance, or both.

A Galinstan-Filled Capillary Probe for Thermal Conductivity Measurements and Its Application to Molten Eutectic {KNO}_3-{NaNO}_3-{NO}_2 (HTS) up to 700 K

NASA Astrophysics Data System (ADS)

Le Brun, Niccolò; Markides, Christos N.

2015-11-01

The successful measurement of the thermal conductivity of molten salts is a challenging undertaking due to the electrically conducting and possibly also aggressive nature of the materials, as well as the elevated temperatures at which these data are required. For accurate and reproducible measurements, it is important to develop a suitable experimental apparatus and methodology. In this study, we explore a modified version of the transient hot-wire method, which employs a molten-metal-filled capillary in order to circumvent some of the issues encountered in previous studies. Specifically, by using a novel flexible U-shaped quartz-capillary, filled with a eutectic mixture of gallium, indium and tin, commercially known as Galinstan, we proceed to measure the thermal conductivity of molten eutectic {KNO}_3-{NaNO}_3-{NaNO}_2. The new probe is demonstrated as being able to measure the thermal conductivity of this molten salt, which is found to range from 0.48 {W}{\\cdot }{m}^{-1}{\\cdot }{K}^{-1} at 500 K to 0.47 {W}{\\cdot }{m}^{-1}{\\cdot }{K}^{-1} at close to 700 K, with an overall expanded uncertainty (95 % confidence) of 3.1 %. The quartz is found to retain its electrically insulating properties and no current leakage is detected in the sample over the investigated temperature range. The thermal conductivity data reported in the present study are also used to elucidate a partial disagreement found in the literature for this material.

Hydrology and water quality of Elkhead Creek and Elkhead Reservoir near Craig, Colorado, July 1995-September 2001

USGS Publications Warehouse

Kuhn, Gerhard; Stevens, Michael R.; Elliott, John G.

2003-01-01

The U.S. Geological Survey, in cooperation with the Colorado River Water Conservation District, collected and analyzed baseline streamflow and water-quality information for Elkhead Creek and water-quality and trophic-state information for Elkhead Reservoir from July 1995 through September 2001. In the study area, Elkhead Creek is a meandering, alluvial stream dominated by snowmelt in mountainous headwaters that produces most of the annual discharge volume and discharge peaks during late spring and early summer. During most of water year 1996 (a typical year), daily mean discharge at station 09246400 (downstream from the reservoir) was similar to daily mean discharge at station 09246200 (upstream from the reservoir). Flow-duration curves for stations 09246200 and 09246400 were nearly identical, except for discharges less than about 10 cubic feet per second. Specific conductance generally had an inverse relation to discharge in Elkhead Creek. During late fall and winter when discharge was small and derived mostly from ground water, specific conductance was high, whereas during spring and early summer, when discharge was large and derived mostly from snowmelt, specific conductance was low. Water temperatures in Elkhead Creek were smallest during winter, about 0.0 degrees Celsius (oC), and largest during summer, about 20?25oC. Concentrations of major ions, nutrients, trace elements, organic carbon, and suspended sediment in Elkhead Creek indicated no substantial within-year variability and no substantial differences in variability from one year to the next. A seasonal pattern in the concentration data was evident for most constituents. The seasonal concentration pattern for most of the dissolved constituents followed the seasonal pattern of specific conductance, whereas some nutrients, some trace elements, and suspended sediment followed the seasonal pattern of discharge. Statistical differences between station 09246200 (upstream from the reservoir) and station 09246400 (downstream from the reservoir) were indicated for specific conductance, dissolved calcium, magnesium, sodium, and sulfate, acid-neutralizing capacity, and dissolved solids. Trend analysis indicated upward temporal trends for pH, dissolved ammonia plus organic nitrogen, total nitrogen, and total phosphorus at station 09246200; upward temporal trends for dissolved and total ammonia plus organic nitrogen, total nitrogen, and total phosphorus were indicated at station 09246400. No downward trends were indicated for any constituents. Annual loads for dissolved constituents during water years 1996?2001 were consistently larger at station 09246400 than at station 09246200, except for silica and sulfate. Mean monthly loads for dissolved constituents followed the seasonal pattern of discharge, indicating that most of the annual loads were transported during March?June. Annual dissolved nutrient loads at stations 09246400 and 09246200 were not substantially different, except for total phosphorus and total nitrogen loads, which were smaller at the downstream station than at the upstream station, most likely due to biological uptake and settling in the reservoir. Mean annual suspended-sediment load during water years 1996?2001 was about 87-percent smaller at the downstream station than at the upstream station. Temperature in Elkhead Reservoir varied seasonally, from about 0oC during winter when ice develops on the reservoir to about 20oC during summer. Specific conductance varied from minimums of 138 to 169 microsiemens per centimeter at 25oC (?S/cm) during snowmelt inflow to maximums of 424 to 610 ?S/cm during early spring low flow (April). Median pH in the reservoir ranged from 7.2 to 8.0 at all sites near the surface. Median dissolved oxygen ranged from 7.1 to 7.2 milligrams per liter (mg/L) in near-surface samples and from 4.8 to 5.6 mg/L in near-bottom samples. During reservoir stratification, specific conductance generally was largest in the e

Physical and chemical characteristics of Lake Powell at the forebay and outflows of Glen Canyon Dam, northeastern Arizona, 1990-91

USGS Publications Warehouse

Hart, R.J.; Sherman, K.M.

1996-01-01

The physical and chemical characteristics of Lake Powell have a direct effect on the quality of water below Glen Canyon Dam. Understanding the physical and chemical characteristics of the lake and outflows from the dam is essential in order to effectively manage the operation of the dam. During August 1990 to September 1991, physical and chemical measurements were made and water samples were collected in the forebay of Lake Powell and at the outflows (draft tubes) of Glen Canyon Dam to document the physical and chemical characteristics of water entering the Colorado River. A persistent chemocline in the forebay of Lake Powell fluctuated seasonally during the study. Thermal stratification began in mid-April and persisted into late October. Spatial variation of specific conductance, pH, water temperature, and dissolved-oxygen concentration in the forebay was negligible. Sodium and sulfate were the dominant ions. Major ions, nutrients, and metals generally increased in concentration with depth in the forebay. Concentrations of dissolved nitrogen (as nitrite plus nitrate) in the forebay ranged from less than 0.02 to 0.58 milligrams per liter. Strontium and lithium were the most abundant metals. Dissolved organic carbon ranged from about 2.6 to 4.9 milligrams per. liter with larger concentrations generally occurring in the epilimnion. No diel variations of chemical constituents were observed. Vertical-attenuation coefficients of light penetration in the forebay ranged from 0.058 to 0.080 microeinsteins per meter squared per second, and the euphotic depth ranged from about 82 to 113 feet. Generally, the physical and chemical characteristics of outflows through the draft tubes of Glen Canyon Dam were similar to the physical and chemical characteristics of the water at penstock depth and deeper depths. Specific conductance ranged from 803 to 1,090 microsiemens per centimeter, and pH values ranged from about 7.2 to 8.0. Water temperatures measured in the outflows ranged from 7.0 to 9.0 degrees Celsius, and dissolved oxygen ranged from about 6.5 to 9.1 milligrams per liter. Concentrations of dissolved nitrogen (as nitrite plus nitrate) ranged from 0.13 to 0.74 milligrams per liter. Dissolved phosphorus (as orthophosphate) and ammonia (NH4) generally were less than the minimum reporting level of 0.01 milligrams per liter. Availability and Quality of Water from Drift Aquifers in Marshall, Pennington, Polk, and Red Lake Counties, Northwestern Minnesota By R.J. Lindgren Abstract Sand and gravel aquifers present within glacial deposits are important sources of water in Marshall, Pennington, Polk, and Red Lake Counties in northwestern Minnesota. Saturated thicknesses of the unconfined aquifers range from 0 to 30 feet. Estimated horizontal hydraulic conductivities range from 2.5 to 600 feet per day. Transmissivity of the unconfined aquifers ranges from 33 to greater than 3,910 feet squared per day. Theoretical maximum well yields for 6 wells with specific-capacity data range from 12 to 123 gallons per minute. Saturated thicknesses of shallow confined aquifers (depth to top of the aquifer less than 100 feet below land surface) range from 0 to 150 feet. Thicknesses of intermediate, deep, and basal confined aquifers (depths to top of the aquifer from 100 to 199 feet, from 200 to 299 feet, and 300 feet or more below land surface, respectively) range from 0 to more than 126 feet. Transmissivity of the confined aquifers ranges from 2 to greater than 210,000 feet squared per day. Theoretical maximum well yields range from 3 to about 2,000 gallons per minute. Recharge to ground water is predominantly from precipitation that percolates downward to the saturated zone. Recharge to unconfined aquifers in the study area ranged from 4.5 to 12.0 inches per year during 1991 and 1992, based on hydrograph analysis. Model simulations done for this study indicate that recharge rates from 8 to 9 inches per year to unconfined aquifers produce the best matches

Ground-water monitoring plan, water quality, and variability of agricultural chemicals in the Missouri River alluvial aquifer near the City of Independence, Missouri, well field, 1998-2000

USGS Publications Warehouse

Kelly, Brian P.

2002-01-01

A detailed ground-water sampling plan was developed and executed for 64 monitoring wells in the city of Independence well field to characterize ground-water quality in the 10-year zone of contribution. Samples were collected from monitoring wells, combined Independence well field pumpage, and the Missouri River at St. Joseph, Missouri, from 1998 through 2000. In 328 ground-water samples from the 64 monitoring wells and combined well field pumpage samples, specific conductance values ranged from 511 to 1,690 microsiemens per centimeter at 25 degrees Celsius, pH values ranged from 6.4 to 7.7, water temperature ranged from 11.3 to 23.6 degrees Celsius, and dissolved oxygen concentrations ranged from 0 to 3.3 milligrams per liter. In 12 samples from the combined well field pumpage samples, specific conductance values ranged from 558 to 856 microsiemens per centimeter at 25 degrees Celsius, pH values ranged from 6.9 to 7.7, water temperature ranged from 5.8 to 22.9 degrees Celsius, and dissolved oxygen concentrations ranged from 0 to 2.4 milligrams per liter. In 45 Missouri River samples, specific conductance values ranged from 531 to 830 microsiemens per centimeter at 25 degrees Celsius, pH ranged from 7.2 to 8.7, water temperature ranged from 0 to 30 degrees Celsius, and dissolved oxygen concentrations ranged from 5.0 to 17.6 milligrams per liter. The secondary maximum contaminant level for sulfate in drinking water was exceeded once in samples from two monitoring wells, the maximum contaminant level (MCL) for antimony was exceeded once in a sample from one monitoring well, and the MCL for barium was exceeded once in a sample from one monitoring well. The MCL for iron was exceeded in samples from all monitoring wells except two. The MCL for manganese was exceeded in all samples from monitoring wells and combined well field pumpage. Enzyme linked immunoassay methods indicate total benzene, toluene, ethyl benzene, and xylene (BTEX) was detected in samples from five wells. The highest total BTEX concentration was less than the MCL of toluene, ethyl benzene, or xylene but greater than the MCL for benzene. Total BTEX was not detected in samples from any well more than once. Atrazine was detected in samples from nine wells, and exceeded the MCL once in a sample from one well. Alachlor was detected in samples from 22 wells but the MCL was never exceeded in any sample. Samples from five wells analyzed for a large number of organic compounds indicate concentrations of volatile organic compounds did not exceed the MCL for drinking water. No semi-volatile organic compounds were detected; dieldrin was detected in one well sample, and no other pesticides, herbicides, polychlorinated biphenyls, or polychlorinated napthalenes were detected. Dissolved ammonia, dissolved nitrite plus nitrate, dissolved orthophosphorus, alachlor, and atrazine analyses were used to determine the spatial and temporal variability of agricultural chemicals in ground water. Detection frequencies for dissolved ammonia increased with well depth, decreased with depth for dissolved nitrite plus nitrate, and remained relatively constant with depth for dissolved orthophosphorus. Maximum concentrations of dissolved ammonia, dissolved nitrite plus nitrate, and dissolved orthophosphorus were largest in the shallowest wells and decreased with depth, which may indicate the land surface as the source. However, median concentrations increased with depth for dissolved ammonia, were less than the detection limit for dissolved nitrite plus nitrate, and decreased with depth for dissolved orthophosphorus. This pattern does not indicate a well-defined single source for these constituents. Dissolved orthophosphorus median concentrations were similar, but decreased slightly with depth, and may indicate the land surface as the source. Seasonal variability of dissolved ammonia, dissolved nitrite plus nitrate, a

Simultaneous Measurement of Thermophysical Properties of Tissue-Mimicking Phantoms for High Intensity Focused Ultrasound (HIFU) Exposures

NASA Astrophysics Data System (ADS)

Gao, Jing; You, Jiang; Huang, Zhihong; Cochran, Sandy; Corner, George

2012-03-01

Tissue-mimicking phantoms, including bovine serum albumin phantoms and egg white phantoms, have been developed for, and in laboratory use for, real-time visualization of high intensity focused ultrasound-induced thermal coagulative necrosis since 2001. However, until now, very few data are available concerning their thermophysical properties. In this article, a step-wise transient plane source method has been used to determine the values of thermal conductivity, thermal diffusivity, and specific heat capacity of egg white phantoms with elevated egg white concentrations (0 v/v% to 40 v/v%, by 10 v/v% interval) at room temperature (~20 °C). The measured thermophysical properties were close to previously reported values; the thermal conductivity and thermal diffusivity were linearly proportional to the egg white concentration within the investigation range, while the specific heat capacity decreased as the egg white concentration increased. Taking account of large differences between real experiment and ideal model, data variations within 20 % were accepted.

Broad specification fuels combustion technology program

NASA Technical Reports Server (NTRS)

Dodds, W. J.; Ekstedt, E. E.

1984-01-01

Design and development efforts to evolve promising aircraft gas turbine combustor configurations for burning broadened-properties fuels were discussed. Design and experimental evaluations of three different combustor concepts in sector combustor rig tests was conducted. The combustor concepts were a state of the art single-annular combustor, a staged double-annular combustor, and a short single-annular combustor with variable geometry to control primary zone stoichiometry. A total of 25 different configurations of the three combustor concepts were evaluated. Testing was conducted over the full range of CF6-80A engine combustor inlet conditions, using four fuels containing between 12% and 14% hydrogen by weight. Good progress was made toward meeting specific program emissions and performance goals with each of the three combustor concepts. The effects of reduced fuel hydrogen content, including increased flame radiation, liner metal temperature, smoke, and NOx emissions were documented. The most significant effect on the baseline combustor was a projected 33% life reduction, for a reduction from 14% to 13% fuel hydrogen content, due to increased liner temperatures.

Semi-Interpenetrating Polymer Networks for Enhanced Supercapacitor Electrodes.

PubMed

Fong, Kara D; Wang, Tiesheng; Kim, Hyun-Kyung; Kumar, R Vasant; Smoukov, Stoyan K

2017-09-08

Conducting polymers show great promise as supercapacitor materials due to their high theoretical specific capacitance, low cost, toughness, and flexibility. Poor ion mobility, however, can render active material more than a few tens of nanometers from the surface inaccessible for charge storage, limiting performance. Here, we use semi-interpenetrating networks (sIPNs) of a pseudocapacitive polymer in an ionically conductive polymer matrix to decrease ion diffusion length scales and make virtually all of the active material accessible for charge storage. Our freestanding poly(3,4-ethylenedioxythiophene)/poly(ethylene oxide) (PEDOT/PEO) sIPN films yield simultaneous improvements in three crucial elements of supercapacitor performance: specific capacitance (182 F/g, a 70% increase over that of neat PEDOT), cycling stability (97.5% capacitance retention after 3000 cycles), and flexibility (the electrodes bend to a <200 μm radius of curvature without breaking). Our simple and controllable sIPN fabrication process presents a framework to develop a range of polymer-based interpenetrated materials for high-performance energy storage technologies.

Comparing biomarker measurements to a normal range: when ...

EPA Pesticide Factsheets

This commentary is the second of a series outlining one specific concept in interpreting biomarkers data. In the first, an observational method was presented for assessing the distribution of measurements before making parametric calculations. Here, the discussion revolves around the next step, the choice of using standard error of the mean or the calculated standard deviation to compare or predict measurement results. The National Exposure Research Laboratory’s (NERL’s) Human Exposure and Atmospheric Sciences Division (HEASD) conducts research in support of EPA’s mission to protect human health and the environment. HEASD’s research program supports Goal 1 (Clean Air) and Goal 4 (Healthy People) of EPA’s strategic plan. More specifically, our division conducts research to characterize the movement of pollutants from the source to contact with humans. Our multidisciplinary research program produces Methods, Measurements, and Models to identify relationships between and characterize processes that link source emissions, environmental concentrations, human exposures, and target-tissue dose. The impact of these tools is improved regulatory programs and policies for EPA.

2011 NASA Range Safety Annual Report

NASA Technical Reports Server (NTRS)

Dumont, Alan G.

2012-01-01

Welcome to the 2011 edition of the NASA Range Safety Annual Report. Funded by NASA Headquarters, this report provides a NASA Range Safety overview for current and potential range users. As is typical with odd year editions, this is an abbreviated Range Safety Annual Report providing updates and links to full articles from the previous year's report. It also provides more complete articles covering new subject areas, summaries of various NASA Range Safety Program activities conducted during the past year, and information on several projects that may have a profound impact on the way business will be done in the future. Specific topics discussed and updated in the 2011 NASA Range Safety Annual Report include a program overview and 2011 highlights; Range Safety Training; Range Safety Policy revision; Independent Assessments; Support to Program Operations at all ranges conducting NASA launch/flight operations; a continuing overview of emerging range safety-related technologies; and status reports from all of the NASA Centers that have Range Safety responsibilities. Every effort has been made to include the most current information available. We recommend this report be used only for guidance and that the validity and accuracy of all articles be verified for updates. Once again the web-based format was used to present the annual report. We continually receive positive feedback on the web-based edition and hope you enjoy this year's product as well. As is the case each year, contributors to this report are too numerous to mention, but we thank individuals from the NASA Centers, the Department of Defense, and civilian organizations for their contributions. In conclusion, it has been a busy and productive year. I'd like to extend a personal Thank You to everyone who contributed to make this year a successful one, and I look forward to working with all of you in the upcoming year.

Can carbon nanotube fibers achieve the ultimate conductivity?—Coupled-mode analysis for electron transport through the carbon nanotube contact

NASA Astrophysics Data System (ADS)

Xu, Fangbo; Sadrzadeh, Arta; Xu, Zhiping; Yakobson, Boris I.

2013-08-01

Recent measurements of carbon nanotube (CNT) fibers electrical conductivity still show the values lower than that of individual CNTs, by about one magnitude order. The imperfections of manufacturing process and constituent components are described as culprits. What if every segment is made perfect? In this work, we study the quantum conductance through the parallel junction of flawless armchair CNTs using tight-binding method in conjunction with non-equilibrium Green's function approach. Short-range oscillations within the long-range oscillations as well as decaying envelopes are all observed in the computed Fermi-level (low bias) conductance as a function of contact length, L. The propagation of CNTs' Bloch waves is cast in the coupled-mode formalism and helps to reveal the quantum interference nature of various behaviors of conductance. Our analysis shows that the Bloch waves at the Fermi-level propagate through a parallel junction without reflection only at an optimal value of contact length. For quite a long junction, however, the conductance at the Fermi level diminishes due to the perturbation of periodic potential field of close-packed CNTs. Thus, a macroscopic fiber, containing an infinite number of junctions, forms a filter that permits passage of electrons with specific wave vectors, and these wave vectors are determined by the collection of all the junction lengths. We also argue that the energy gap introduced by long junctions can be overcome by small voltage (˜0.04 V) across the whole fiber. Overall, developing long individual all-armchair metallic CNTs serves as a promising way to the manufacture of high-conductivity fibers.

Performance potential of air turbo-ramjet employing supersonic through-flow fan

NASA Technical Reports Server (NTRS)

Kepler, C. E.; Champagne, G. A.

1989-01-01

A study was conducted to assess the performance potential of a supersonic through-flow fan in an advanced engine designed to power a Mach-5 cruise vehicle. It included a preliminary evaluation of fan performance requirements and the desirability of supersonic versus subsonic combustion, the design and performance of supersonic fans, and the conceptual design of a single-pass air-turbo-rocket/ramjet engine for a Mach 5 cruise vehicle. The study results showed that such an engine could provide high thrust over the entire speed range from sea-level takeoff to Mach 5 cruise, especially over the transonic speed range, and high fuel specific impulse at the Mach 5 cruise condition, with the fan windmilling.

Dielectric study of chalcogenide (Se80Te20)94Ge6 glass

NASA Astrophysics Data System (ADS)

Sharma, Neha; Patial, Balbir Singh; Thakur, Nagesh

2018-04-01

In the present study, dielectric characteristics specifically dielectric constant (ɛ'), dielectric loss (ɛ″) and AC conductivity (σAC) have been investigated for chalcogenide (Se80Te20)94Ge6 glass in the frequency range from 1Hz to 1MHz and within the temperature range from 300 K to 380 K. ɛ'(ω) and ɛ″(ω) are found to be frequency and temperature dependent. This behaviour is interpreted on the basis of Guintini's theory of dielectric dispersion. The investigated glass obeys the power law ωs (s<1) and decreases as temperature rises. The obtained results are discussed in terms of the correlation barrier hopping (CBH) model proposed by Elliot.

Heat Pipe Thermal Conditioning Panel

NASA Technical Reports Server (NTRS)

Saaski, E. W.

1973-01-01

The technology involved in designing and fabricating a heat pipe thermal conditioning panel to satisfy a broad range of thermal control system requirements on NASA spacecraft is discussed. The design specifications were developed for a 30 by 30 inch heat pipe panel. The fundamental constraint was a maximum of 15 gradient from source to sink at 300 watts input and a flux density of 2 watts per square inch. The results of the performance tests conducted on the panel are analyzed.

Renewal of the Nellis Air Force Range Land Withdrawal, Legislative Environmental Impact Statement. Volume 1. Chapters 1-11

DTIC Science & Technology

1999-03-01

data on geologic setting, metallic and industrial minerals, gemstones, uranium, geothermal resources, and oil and gas resources on the NAFR lands...were conducted during the RFA. The SWMUs and AOCs found on NAFR include ECM sites, oil /water separators, acid neutralizing basins and oil interceptors...inspected. No specific recommendations provided. Area 10 Oil /Water Separator Bldg 145 Oil /water separator handles influent from wash and rinse basins

Water-quality reconnaissance of the Pascagoula and Escatawpa Rivers, Jackson County, Mississippi, May 1974 to July 1978

USGS Publications Warehouse

Faye, Robert E.

1980-01-01

Short-term, water-quality reconnaissances along the downstream reaches of the Pascagoula and Escatawpa Rivers in Jackson County , Miss., indicate that stream quality during the period May 1974 to July 1978 was affected by wastewater discharges as well as river discharge and the extent of tidal intrusion. Specific conductances on the Pascagoula River ranged from less than 100 to more than 40,000 micromhos per centimeter and increased downstream. Specific conductance also increased with depth at downstram sites, indicating density stratification. Dissolved-oxygen concentrations were also affected by density stratification but were generally greater than 4.0 milligrams per liter in both rivers. Analyses of 5-day biochemical oxygen demand and nutrient concentrations indicate that oxidation of both carbonaceous and nitrogenous materials significantly affected the waste assimilative capacity of the rivers. Concentrations of pesticides and most trace elements in both the water column and the bottom sediments were zero or very small. Titanium concentrations were less than 220 micrograms per liter in the water column and 6,500 micrograms per gram in bottom sediments. Small concentrations of oil and grease, PCB's, and phenols were also detected. Fecal coliform and fecal streptococcal bacteria concentrations were generally greater in the Escatawpa River and ranged from about 10 to 18,000 colonies per 100 milliliters of water. (USGS)

Waste heat generation: A comprehensive review.

PubMed

Yeşiller, Nazli; Hanson, James L; Yee, Emma H

2015-08-01

A comprehensive review of heat generation in various types of wastes and of the thermal regime of waste containment facilities is provided in this paper. Municipal solid waste (MSW), MSW incineration ash, and mining wastes were included in the analysis. Spatial and temporal variations of waste temperatures, thermal gradients, thermal properties of wastes, average temperature differentials, and heat generation values are provided. Heat generation was influenced by climatic conditions, mean annual earth temperatures, waste temperatures at the time of placement, cover conditions, and inherent heat generation potential of the specific wastes. Time to onset of heat generation varied between months and years, whereas timelines for overall duration of heat generation varied between years and decades. For MSW, measured waste temperatures were as high as 60-90°C and as low as -6°C. MSW incinerator ash temperatures varied between 5 and 87°C. Mining waste temperatures were in the range of -25 to 65°C. In the wastes analyzed, upward heat flow toward the surface was more prominent than downward heat flow toward the subsurface. Thermal gradients generally were higher for MSW and incinerator ash and lower for mining waste. Based on thermal properties, MSW had insulative qualities (low thermal conductivity), while mining wastes typically were relatively conductive (high thermal conductivity) with ash having intermediate qualities. Heat generation values ranged from -8.6 to 83.1MJ/m(3) and from 0.6 to 72.6MJ/m(3) for MSW and mining waste, respectively and was 72.6MJ/m(3) for ash waste. Conductive thermal losses were determined to range from 13 to 1111MJ/m(3)yr. The data and analysis provided in this review paper can be used in the investigation of heat generation and thermal regime of a wide range of wastes and waste containment facilities located in different climatic regions. Copyright © 2015 Elsevier Ltd. All rights reserved.

The thermal and physical characteristics of the Gao-Guenie (H5) meteorite

NASA Astrophysics Data System (ADS)

Beech, Martin; Coulson, Ian M.; Nie, Wenshuang; McCausland, Phil

2009-06-01

Measurements of the bulk density, grain density, porosity, and magnetic susceptibility of 19 Gao-Guenie H5 chondrite meteorite samples are presented. We find average values of bulk density < ρbulk>=3.46±0.07 g/cm 3, grain density < ρgrain>=3.53±0.08 g/cm 3, porosity < P(%)>=2.46±1.39, and bulk mass magnetic susceptibility =5.23±0.11. Measurements of the specific heat capacity for a 3.01-g Gao-Guenie sample, a 61.37-g Gao-Guenie sample, a 62.35-g Jilin H5 chondrite meteorite sample, and a 51.37-g Sikhote-Alin IIAB Iron meteorite sample are also presented. Temperature interpolation formula are further provided for the specific heat capacity, thermal conductivity, and thermal diffusivity of the 3.01-g Gao-Guenie sample in the temperature range 300< T (K)<800. We briefly review the possible effects of the newly deduced specific heat and thermal conductivity values on the ablation of meteoroids within the Earth's atmosphere, the modeling of asteroid interiors and the orbital evolution of meteoroids through the Yarkovsky-O'Keefe-Radzievskii-Paddack (YORP) effect.

A systematic review of screening questionnaires for childhood lead poisoning.

PubMed

Ossiander, Eric M

2013-01-01

The Centers for Disease Control and Prevention encourages the use of risk factor questionnaires to screen children for lead poisoning. A majority of state health departments have formal lead screening guidelines that recommend health care providers use questionnaires. We conducted a systematic review to evaluate the ability of lead screening questionnaires to predict lead poisoning risk among children. Articles that reported the evaluation of a predesigned lead screening questionnaire were obtained by searching Medline/PubMed and by examining references of articles obtained through the online search. From each evaluation, we abstracted the number of children that were true positive, false positive, true negative, and false negative, according to the results of the screening questionnaire and the follow-up blood lead test. From these data, we calculated specificity and sensitivity of the questionnaire for each evaluation. Twenty articles met the inclusion criteria: these included 28 separate questionnaire evaluations. Among 17 evaluations of the 1991 Centers for Disease Control and Prevention questionnaire, sensitivity ranged from 0.25 to 0.87, specificity from 0.31 to 0.80, and accuracy (sum of sensitivity and specificity) from 0.74 to 1.39. The pooled mean estimates for this questionnaire were sensitivity 0.61 (95% confidence interval: 0.53-0.68); specificity 0.52 (0.45-0.60); accuracy 1.12 (1.06-1.18). Among 11 evaluations of all other questionnaires, sensitivity ranged from 0.43 to 0.90, specificity from 0.17 to 0.66, and accuracy from 0.94 to 1.27. For these questionnaires, the pooled mean estimates were sensitivity 0.76 (0.68-0.85), specificity 0.41 (0.33-0.49), and accuracy 1.12 (1.06-1.18). Lead screening questionnaires showed a wide range of sensitivity and specificity and performed little better than chance at predicting lead poisoning risk among children.

A systematic review of the sensitivity and specificity of the toe-brachial index for detecting peripheral artery disease.

PubMed

Tehan, Peta Ellen; Santos, Derek; Chuter, Vivienne Helaine

2016-08-01

The toe-brachial index (TBI) is used as an adjunct to the ankle-brachial index (ABI) for non-invasive lower limb vascular screening. With increasing evidence suggesting limitations of the ABI for diagnosis of vascular complications, particularly in specific populations including diabetes cohorts, the TBI is being used more widely. The aim of this review was to determine the sensitivity and specificity of the TBI for detecting peripheral artery disease (PAD) in populations at risk of this disease. A database search was conducted to identify current work relating to the sensitivity and specificity of toe-brachial indices up to July 2015. Only studies using valid diagnostic imaging as a reference standard were included. The QUADAS-2 tool was used to critically appraise included articles. Seven studies met the inclusion criteria. Sensitivity of the TBI for PAD was reported in all seven studies and ranged from 45% to 100%; specificity was reported by five studies only and ranged from 16% to 100%. In conclusion, this review suggests that the TBI has variable diagnostic accuracy for the presence of PAD in specific populations at risk of developing the disease. There was a notable lack of large-scale diagnostic accuracy studies determining the diagnostic accuracy of the TBI in detecting PAD in different at-risk cohorts. However, standardised normal values need to be established for the TBI to conclusively determine the diagnostic accuracy of this test. © The Author(s) 2016.

Feeding behaviour of the nauplii of the marine calanoid copepod Paracartia grani Sars: Functional response, prey size spectrum, and effects of the presence of alternative prey.

PubMed

Helenius, Laura K; Saiz, Enric

2017-01-01

Laboratory feeding experiments were conducted to study the functional response and prey size spectrum of the young naupliar stages of the calanoid copepod Paracartia grani Sars. Experiments were conducted on a range of microalgal prey of varying sizes and motility patterns. Significant feeding was found in all prey of a size range of 4.5-19.8 μm, with Holling type III functional responses observed for most prey types. The highest clearance rates occurred when nauplii fed on the dinoflagellate Heterocapsa sp. and the diatom Thalassiosira weissflogii (respectively, 0.61 and 0.70 mL ind-1 d-1), suggesting an optimal prey:predator ratio of 0.09. Additional experiments were conducted to examine the effects of the presence of alternative prey (either Heterocapsa sp. or Gymnodinium litoralis) on the functional response to the haptophyte Isochrysis galbana. In the bialgal mixtures, clearance and ingestion rates of I. galbana along the range of the functional response were significantly reduced as a result of selectivity towards the larger, alternative prey. Paradoxically, relatively large prey trigger a perception response in the nauplii, but most likely such prey cannot be completely ingested and a certain degree of sloppy feeding may occur. Our results are further evidence of the complex prey-specific feeding interactions that are likely to occur in natural assemblages with several available prey types.

Vapor Hydrogen Peroxide as Alternative to Dry Heat Microbial Reduction

NASA Technical Reports Server (NTRS)

Cash, Howard A.; Kern, Roger G.; Chung, Shirley Y.; Koukol, Robert C.; Barengoltz, Jack B.

2006-01-01

The Jet Propulsion Laboratory, in conjunction with the NASA Planetary Protection Officer, has selected vapor phase hydrogen peroxide (VHP) sterilization process for continued development as a NASA approved sterilization technique for spacecraft subsystems and systems. The goal is to include this technique, with appropriate specification, in NPG8020.12C as a low temperature complementary technique to the dry heat sterilization process. A series of experiments were conducted in vacuum to determine VHP process parameters that provided significant reductions in spore viability while allowing survival of sufficient spores for statistically significant enumeration. With this knowledge of D values, sensible margins can be applied in a planetary protection specification. The outcome of this study provided an optimization of test sterilizer process conditions: VHP concentration, process duration, a process temperature range for which the worst case D value may be imposed, a process humidity range for which the worst case D value may be imposed, and robustness to selected spacecraft material substrates.

Differential Modulation of Excitatory and Inhibitory Neurons during Periodic Stimulation

PubMed Central

Mahmud, Mufti; Vassanelli, Stefano

2016-01-01

Non-invasive transcranial neuronal stimulation, in addition to deep brain stimulation, is seen as a promising therapeutic and diagnostic approach for an increasing number of neurological diseases such as epilepsy, cluster headaches, depression, specific type of blindness, and other central nervous system disfunctions. Improving its effectiveness and widening its range of use may strongly rely on development of proper stimulation protocols that are tailored to specific brain circuits and that are based on a deep knowledge of different neuron types response to stimulation. To this aim, we have performed a simulation study on the behavior of excitatory and inhibitory neurons subject to sinusoidal stimulation. Due to the intrinsic difference in membrane conductance properties of excitatory and inhibitory neurons, we show that their firing is differentially modulated by the wave parameters. We analyzed the behavior of the two neuronal types for a broad range of stimulus frequency and amplitude and demonstrated that, within a small-world network prototype, parameters tuning allow for a selective enhancement or suppression of the excitation/inhibition ratio. PMID:26941602

Gasification of agricultural residues in a demonstrative plant: corn cobs.

PubMed

Biagini, Enrico; Barontini, Federica; Tognotti, Leonardo

2014-12-01

Biomass gasification couples the high power efficiency with the possibility of valuably using the byproducts heat and biochar. The use of agricultural wastes instead of woody feedstock extends the seasonal availability of biomasses. The downdraft type is the most used reactor but has narrow ranges of feedstock specifications (above all on moisture and particle size distribution), so tests on a demonstrative scale are conducted to prove the versatility of the gasifier. Measurements on pressure drops, syngas flow rate and composition are studied to assess the feasibility of such operations with corn cobs. Material and energy balances, and performance indexes are compared for the four tests carried out under different biomass loads (66-85 kg/h). A good operability of the plant and interesting results are obtained (gas specific production of 2 m3/kg, gas heating value 5.6-5.8 MJ/m3, cold gas efficiency in the range 66-68%, potential net power efficiency 21.1-21.6%). Copyright © 2014 Elsevier Ltd. All rights reserved.

2013 NASA Range Safety Annual Report

NASA Technical Reports Server (NTRS)

Dumont, Alan G.

2013-01-01

Welcome to the 2013 edition of the NASA Range Safety Annual Report. Funded by NASA Headquarters, this report provides an Agency overview for current and potential range users. This report contains articles which cover a variety of subject areas, summaries of various activities performed during the past year, links to past reports, and information on several projects that may have a profound impact on the way business will be conducted in the future. Specific topics discussed in the 2013 NASA Range Safety Annual Report include a program overview and 2013 highlights, Range Safety Training, Independent Assessments, support to Program Operations at all ranges conducting NASA launch/flight operations, a continuing overview of emerging range safety-related technologies, and status reports from all of the NASA Centers that have Range Safety responsibilities. Every effort has been made to include the most current information available. We recommend this report be used only for guidance and that the validity and accuracy of all articles be verified for updates. As is the case each year, we had a wide variety of contributors to this report from across our NASA Centers and the national range safety community at large, and I wish to thank them all. On a sad note, we lost one of our close colleagues, Dr. Jim Simpson, due to his sudden passing in December. His work advancing the envelope of autonomous flight safety systems software/hardware development leaves a lasting impression on our community. Such systems are being flight tested today and may one day be considered routine in the range safety business. The NASA family has lost a pioneer in our field, and he will surely be missed. In conclusion, it has been a very busy and productive year, and I look forward to working with all of you in NASA Centers/Programs/Projects and with the national Range Safety community in making Flight/Space activities as safe as they can be in the upcoming year.

Conductivity relaxation and charge transport of trihexyl tetradecyl phosphonium dicyanamide ionic liquid by broadband dielectric spectroscopy

NASA Astrophysics Data System (ADS)

Thasneema K., K.; Thayyil, M. Shahin; Krishna Kumar N., S.; Govindaraj, G.; Saheer, V. C.

2018-04-01

Usually ionic liquids consists of a large organic cation with low symmetry such as imidazolium, pyridinium, quaternary ammonium or phosponium etc combined with enormously wide range of inorganic or organic symmetric anion with melting point below 100. Ionic liquids existing in an extremely large number of possible ion pair combinations. It offers a very wide range of thermo physical properties led to the concept of designer solvents for specific applications. Due to the features of high chemical and thermal stability, low vapor pressure non flammability high ionic conductivity, and they show a good solvent ability towards a great variety of organic or inorganic compounds, ionic liquids have a widespread use in many areas such as batteries, fuel cell, solar cells, super capacitors etc. The main focus of this work is the study of molecular dynamics and conductivity relaxation of amorphous Trihexyl tetradecyl phosphonium dicyanamide ([P14,6,6,6][N(CN)2]) ionic liquid which is proved as a better electrolyte in super capacitors, over a wide frequency 10-2 Hz to 107 Hz and the temperature range between 123k and 265 k by means of Broadband Dielectric Spectroscopy. We observe alpha conductivity relaxation and secondary relaxation above and below Glass Transition Temperature. The experimental results were analyzed using electric modulus representation. The analysis emphasis the inter molecular interaction and the nature of glass forming system, whether it is fragile or strong system. The ionic liquid shows a fragile behavior and the fragility index m=123.59. TGA result of the sample exhibit a good resistance to thermal decomposition, up to 300°C.

Scaling of Ion Thrusters to Low Power

NASA Technical Reports Server (NTRS)

Patterson, Michael J.; Grisnik, Stanley P.; Soulas, George C.

1998-01-01

Analyses were conducted to examine ion thruster scaling relationships in detail to determine performance limits, and lifetime expectations for thruster input power levels below 0.5 kW. This was motivated by mission analyses indicating the potential advantages of high performance, high specific impulse systems for small spacecraft. The design and development status of a 0.1-0.3 kW prototype small thruster and its components are discussed. Performance goals include thruster efficiencies on the order of 40% to 54% over a specific impulse range of 2000 to 3000 seconds, with a lifetime in excess of 8000 hours at full power. Thruster technologies required to achieve the performance and lifetime targets are identified.

Preprototype SAWD subsystem

NASA Technical Reports Server (NTRS)

Nalette, T. A.

1984-01-01

A regenerable, three man preprototype solid amine, water desorbed (SAWD) CO2 removal and concentation subsystem was designed, fabricated, and successfully acceptance tested by Hamilton Standard. The preprototype SAWD incorporates a single solid amine canister to perform the CO2 removal function, an accumulator to provide the CO2 storage and delivery function, and a microprocessor which automatically controls the subsystem sequential operation and performance. The SAWD subsystem was configured to have a CO2 removal and CO2 delivery capability at the rate of 0.12 kg/hr (0.264 lb/hr) over the relative humidity range of 35 to 70%. The controller was developed to provide fully automatic control over the relative humidity range via custom software that was generated specifically for the SAWD subsystem. The preprototype SAWD subsystem demonstrated a total of 281 hours (208) cycles of operation during ten acceptance tests that were conducted over the 3 to 70% relative humidity range. This operation was comprised of 178 hours (128 cycles) in the CO2 overboard mode and 103 hours (80 cycles) in the CO2 reduction mode. The average CO2 removal/delivery rate met or exceeded the design specification rate of 0.12 kg/hr (0.254 lb/hr) for all ten of the acceptance tests.

Water quality of the Upper West Branch Susquehanna River and tributary streams between Curwensville and Renovo, Pennsylvania, May and July 1984

USGS Publications Warehouse

Hainly, R.A.; Barker, J.L.

1993-01-01

The soils and rocks of the Upper West Branch Susquehanna River basin, from its headwaters downstream for 150 miles, are laden with pyritic materials that have the potential to produce acid mine drainage. The effects of mine drainage are severe, particularly in the reach between Curwensville and Renovo where present water quality cannot support viable populations of benthic macroinvertebrates or fish. During base-flow periods in May and July 1984, streamflow and water quality were measured at four sites on the West Branch Susquehanna River and near the mouths of 94 tributaries. Water-quality constituents determined were temperature, specific conductance, pH, acidity, alkalinity, and concentrations of dissolved sulfate and total and dissolved forms of iron, manganese, aluminum, and zinc. The data collected for the study indicate that the predominant influence on water quality of the tributaries is land use. An area where few or no coal deposits or disturbed area were present was found to have relatively good surface-water quality (median pH was nearly 5.5 units), whereas areas where coal mining was active in the basin, or where large areas of unreclaimed mines were present, were found to have poorest water quality (median pH was generally less than 4.0 units). In general, Moshannon, Sinnemahoning, Clearfield, and Kettle Creeks were found to be the largest tributary sources of acidity and total-recoverable iron to the river. During the May sampling, Moshannon, Sinnemahoning, and Clearfield Creeks contributed 63 percent of the 365 tons/day of acidity, and Moshannon and Clearfield Creeks contributed 76 percent of the 44.8 tons/day of total-recoverable iron that were discharged to the river. During the July sampling, Moshannon, Kettle, and Clearfield Creeks contributed 60 percent of the 131 tons/day of acidity, and Moshannon and Kettle Creeks contributed 51 percent of the 6.5 tons/day of total-recoverable iron discharged to the river . The West Branch Susquehanna River was found to have pH ranging from 5.4 to 6.5 units and specific conductance ranging from 267 to 310 microsiemens per centimeter at the most upstream site at Curwensville. The water quality was most degraded at the site at Karthaus (pH 3.9 to 4.1 units, specific conductance 330 to 610 microsiemens per centimeter). Quality gradually improved downstream to the site at Renovo (pH 3.8 to 4.6 units, specific conductance 200 to 392 microsiemens per centimeter), although the quality did not recover to that found at Curwensville.

Node of Ranvier length as a potential regulator of myelinated axon conduction speed.

PubMed

Arancibia-Cárcamo, I Lorena; Ford, Marc C; Cossell, Lee; Ishida, Kinji; Tohyama, Koujiro; Attwell, David

2017-01-28

Myelination speeds conduction of the nerve impulse, enhancing cognitive power. Changes of white matter structure contribute to learning, and are often assumed to reflect an altered number of myelin wraps. We now show that, in rat optic nerve and cerebral cortical axons, the node of Ranvier length varies over a 4.4-fold and 8.7-fold range respectively and that variation of the node length is much less along axons than between axons. Modelling predicts that these node length differences will alter conduction speed by ~20%, similar to the changes produced by altering the number of myelin wraps or the internode length. For a given change of conduction speed, the membrane area change needed at the node is >270-fold less than that needed in the myelin sheath. Thus, axon-specific adjustment of node of Ranvier length is potentially an energy-efficient and rapid mechanism for tuning the arrival time of information in the CNS.

Electrical Conductivity of Cancrinite-Type Na8 - 2 x Ca x [Al6Si6O24][CO3] · 2H2O ( x ≤ 0.03) Crystals

NASA Astrophysics Data System (ADS)

Sorokin, N. I.

2018-05-01

The electrical conductivity of crystals of artificial cancrinite Na8 - 2 x Ca x [Al6Si6O24][CO3] · 2H2O ( x ≤ 0.03) has been studied in the temperature range of 498-604 K. These crystals were grown by hydrothermal synthesis on a seed in the Na2O-Al2O3-SiO2-H2O system ( t = 380-420°C, P = 3 × 107-9 × 107 Pa). The ionic conductivity of a single-crystal sample (sp. gr. P63), measured along the crystallographic axis c, is low: σ = 8 × 10-7 S/cm at 300°C. The electric transport activation energy is E a = 0.81 ± 0.05 eV. The relationship between the ionic conductivity and specific features of the atomic structure of cancrinites is discussed.

Investigation of Thermal Properties of High-Density Polyethylene/Aluminum Nanocomposites by Photothermal Infrared Radiometry

NASA Astrophysics Data System (ADS)

Koca, H. D.; Evgin, T.; Horny, N.; Chirtoc, M.; Turgut, A.; Tavman, I. H.

2017-12-01

In this study, thermal properties of high-density polyethylene (HDPE) filled with nanosized Al particles (80 nm) were investigated. Samples were prepared using melt mixing method up to filler volume fraction of 29 %, followed by compression molding. By using modulated photothermal radiometry (PTR) technique, thermal diffusivity and thermal effusivity were obtained. The effective thermal conductivity of nanocomposites was calculated directly from PTR measurements and from the measurements of density, specific heat capacity (by differential scanning calorimetry) and thermal diffusivity (obtained from PTR signal amplitude and phase). It is concluded that the thermal conductivity of HDPE composites increases with increasing Al fraction and the highest effective thermal conductivity enhancement of 205 % is achieved at a filler volume fraction of 29 %. The obtained results were compared with the theoretical models and experimental data given in the literature. The results demonstrate that Agari and Uno, and Cheng and Vachon models can predict well the thermal conductivity of HDPE/Al nanocomposites in the whole range of Al fractions.

Numeric Design and Performance Analysis of Solid Oxide Fuel Cell -- Gas Turbine Hybrids on Aircraft

NASA Astrophysics Data System (ADS)

Hovakimyan, Gevorg

The aircraft industry benefits greatly from small improvements in aircraft component design. One possible area of improvement is in the Auxiliary Power Unit (APU). Modern aircraft APUs are gas turbines located in the tail section of the aircraft that generate additional power when needed. Unfortunately the efficiency of modern aircraft APUs is low. Solid Oxide Fuel Cell/Gas Turbine (SOFC/GT) hybrids are one possible alternative for replacing modern gas turbine APUs. This thesis investigates the feasibility of replacing conventional gas turbine APUs with SOFC/GT APUs on aircraft. An SOFC/GT design algorithm was created in order to determine the specifications of an SOFC/GT APU. The design algorithm is comprised of several integrated modules which together model the characteristics of each component of the SOFC/GT system. Given certain overall inputs, through numerical analysis, the algorithm produces an SOFC/GT APU, optimized for specific power and efficiency, capable of performing to the required specifications. The SOFC/GT design is then input into a previously developed quasi-dynamic SOFC/GT model to determine its load following capabilities over an aircraft flight cycle. Finally an aircraft range study is conducted to determine the feasibility of the SOFC/GT APU as a replacement for the conventional gas turbine APU. The design results show that SOFC/GT APUs have lower specific power than GT systems, but have much higher efficiencies. Moreover, the dynamic simulation results show that SOFC/GT APUs are capable of following modern flight loads. Finally, the range study determined that SOFC/GT APUs are more attractive over conventional APUs for longer range aircraft.

First order transitions by conduction calorimetry: Application to deuterated potassium dihydrogen phosphate ferroelastic crystal under uniaxial pressure

NASA Astrophysics Data System (ADS)

Gallardo, M. C.; Jiménez, J.; Koralewski, M.; del Cerro, J.

1997-03-01

The specific heat c and the heat power W exchanged by a Deuterated Potassium Dihydrogen Phosphate ferroelectric-ferroelastic crystal have been measured simultaneously for both decreasing and increasing temperature at a low constant rate (0.06 K/h) between 175 and 240 K. The measurements were carried out under controlled uniaxial stresses of 0.3 and 4.5±0.1 bar applied to face (110). At Tt=207.9 K, a first order transition is produced with anomalous specific heat behavior in the interval where the transition heat appears. This anomalous behavior is explained in terms of the temperature variation of the heat power during the transition. During cooling, the transition occurs with coexistence of phases, while during heating it seems that metastable states are reached. Excluding data affected by the transition heat, the specific heat behavior agrees with the predictions of a 2-4-6 Landau potential in the range of 4-15 K below Tt while logarithmic behavior is obtained in the range from Tt to 1 K below Tt. Data obtained under 0.3 and 4.5 bar uniaxial stresses exhibit the same behavior.

Contrasting physiological responses to excess heat and irradiance in two tropical savanna sedges

PubMed Central

John-Bejai, C.; Farrell, A. D.; Cooper, F. M.; Oatham, M. P.

2013-01-01

Tropical hyperseasonal savannas provide a rare example of a tropical climax community dominated by graminoid species. Species living in such savannas are frequently exposed to excess heat and light, in addition to drought and waterlogging, and must possess traits to avoid or tolerate these stress factors. Here we examine the contrasting heat and light stress adaptations of two dominant savanna sedges: Lagenocarpus guianensis, which is restricted to the sheltered forest edge, and Lagenocarpus rigidus, which extends from the forest edge to the open savanna. An ecotone extending from the forest edge to the open savanna was used to assess differences in a range of physiological traits (efficiency of photosystem II, cell membrane thermostability, stomatal conductance, leaf surface reflectance and canopy temperature depression) and a range of leaf functional traits (length : width ratio, specific leaf area and degree of folding). Lagenocarpus guianensis showed significantly less canopy temperature depression than L. rigidus, which may explain why this species was restricted to the forest edge. The range of leaf temperatures measured was within the thermal tolerance of L. guianensis and allowed photosystem II to function normally, at least within the cool forest edge. The ability of L. rigidus to extend into the open savanna was associated with an ability to decouple leaf temperature from ambient temperature combined with enhanced cell membrane thermostability. The high degree of canopy temperature depression seen in L. rigidus was not explained by enhanced stomatal conductance or leaf reflectance, but was consistent with a capacity to increase specific leaf area and reduce leaf length: width ratio in the open savanna. Plasticity in leaf functional traits and in cell membrane thermostability are key factors in the ability of this savanna sedge to survive abiotic stress. PMID:24379971

Water-quality and sediment-chemistry data of drain water and evaporation ponds from Tulare Lake Drainage District, Kings County, California March 1985 to March 1986

USGS Publications Warehouse

Fujii, Roger

1988-01-01

Trace element and major ion concentrations were measured in water samples collected monthly between March 1985 and March 1986 at the MD-1 pumping station at the Tulare Lake Drainage District evaporation ponds, Kings County, California. Samples were analyzed for selected pesticides several times during the year. Salinity, as measured by specific conductance, ranged from 11,500 to 37,600 microsiemens/centimeter; total recoverable boron ranged from 4,000 to 16,000 micrg/L; and total recoverable molybdenum ranged from 630 to 2,600 microg/L. Median concentrations of total arsenic and total selenium were 97 and 2 microg/L. Atrazine, prometone, propazine, and simazine were the only pesticides detected in water samples collected at the MD-1 pumping station. Major ions, trace elements, and selected pesticides also were analyzed in water and bottom-sediment samples from five of the southern evaporation ponds at Tulare Lake Drainage District. Water enters the ponds from the MD-1 pumping station at pond 1 and flows through the system terminating at pond 10. The water samples increased in specific conductance (21,700 to 90,200 microsiemens/centimeter) and concentrations of total arsenic (110 to 420 microg/L), total recoverable boron (12,000 to 80,000 microg/L) and total recoverable molybdenum (1,200 to 5,500 microg/L) going from pond 1 to pond 10, respectively. Pesticides were not detected in water from any of the ponds sampled. Median concentrations of total arsenic and total selenium in the bottom sediments were 4.0 and 0.9 microg/g, respectively. The only pesticides detected in bottom sediment samples from the evaporation ponds were DDD and DDE, with maximum concentration of 0.8 microg/kilogram. (Author 's abstract)

Strategies used by breast cancer survivors to address work-related limitations during and after treatment.

PubMed

Sandberg, Joanne C; Strom, Carla; Arcury, Thomas A

2014-01-01

The primary objective of this exploratory study was to delineate the broad range of adjustments women breast cancer survivors draw upon to minimize cancer-related limitations at the workplace. The study also analyzed whether survivors used strategies to address work-related limitations in isolation or in combination with other strategies, and whether they used formal or informal strategies. Semi-structured, in-depth interviews were conducted with 14 women who were employed at the time of diagnosis of breast cancer and who continued to work during treatment or returned to work. Interviews were conducted 3 to 24 months after diagnosis. An iterative process was used to systematically analyze the data (the transcripts) using qualitative methods. Participants who worked during or after treatment adjusted their work schedule, performed fewer or other tasks, modified or changed their work environment, reduced non-work activities at the workplace, used cognitive prompts, and acted preemptively to make work tasks manageable after their return to work. Survivors used multiple adjustments and drew upon both formal and informal tactics to minimize or prevent cancer- or treatment-related effects from negatively affecting job performance. Knowledge about the broad range of both formal and informal strategies identified in this study may enable health care and social services providers, as well as cancer survivors and employers, to identify a wide range of specific strategies that may reduce the negative effects of work-related limitations in specific work settings. Insights gained from this analysis should inform future research on work and cancer survivorship. Copyright © 2014 Jacobs Institute of Women's Health. Published by Elsevier Inc. All rights reserved.

Generalized Procedure for Improved Accuracy of Thermal Contact Resistance Measurements for Materials With Arbitrary Temperature-Dependent Thermal Conductivity

DOE PAGES

Sayer, Robert A.

2014-06-26

Thermal contact resistance (TCR) is most commonly measured using one-dimensional steady-state calorimetric techniques. In the experimental methods we utilized, a temperature gradient is applied across two contacting beams and the temperature drop at the interface is inferred from the temperature profiles of the rods that are measured at discrete points. During data analysis, thermal conductivity of the beams is typically taken to be an average value over the temperature range imposed during the experiment. Our generalized theory is presented and accounts for temperature-dependent changes in thermal conductivity. The procedure presented enables accurate measurement of TCR for contacting materials whose thermalmore » conductivity is any arbitrary function of temperature. For example, it is shown that the standard technique yields TCR values that are about 15% below the actual value for two specific examples of copper and silicon contacts. Conversely, the generalized technique predicts TCR values that are within 1% of the actual value. The method is exact when thermal conductivity is known exactly and no other errors are introduced to the system.« less

Electrical conductivity of high-purity germanium crystals at low temperature

NASA Astrophysics Data System (ADS)

Yang, Gang; Kooi, Kyler; Wang, Guojian; Mei, Hao; Li, Yangyang; Mei, Dongming

2018-05-01

The temperature dependence of electrical conductivity of single-crystal and polycrystalline high-purity germanium (HPGe) samples has been investigated in the temperature range from 7 to 100 K. The conductivity versus inverse of temperature curves for three single-crystal samples consist of two distinct temperature ranges: a high-temperature range where the conductivity increases to a maximum with decreasing temperature, and a low-temperature range where the conductivity continues decreasing slowly with decreasing temperature. In contrast, the conductivity versus inverse of temperature curves for three polycrystalline samples, in addition to a high- and a low-temperature range where a similar conductive behavior is shown, have a medium-temperature range where the conductivity decreases dramatically with decreasing temperature. The turning point temperature ({Tm}) which corresponds to the maximum values of the conductivity on the conductivity versus inverse of temperature curves are higher for the polycrystalline samples than for the single-crystal samples. Additionally, the net carrier concentrations of all samples have been calculated based on measured conductivity in the whole measurement temperature range. The calculated results show that the ionized carrier concentration increases with increasing temperature due to thermal excitation, but it reaches saturation around 40 K for the single-crystal samples and 70 K for the polycrystalline samples. All these differences between the single-crystal samples and the polycrystalline samples could be attributed to trapping and scattering effects of the grain boundaries on the charge carriers. The relevant physical models have been proposed to explain these differences in the conductive behaviors between two kinds of samples.

Dynamic effective properties of heterogeneous geological formations with spherical inclusions under periodic time variations

NASA Astrophysics Data System (ADS)

Rabinovich, A.; Dagan, G.; Miloh, T.

2013-04-01

In unsteady groundwater flow (or similar processes of heat/electrical conduction), the heterogeneous medium structure is characterized by two random properties, the conductivity K and the specific storativity S. The average head field ⟨H ⟩and the associated effective properties Kef, Sef are determined for a layer with a periodic head drop between boundaries, such that H is periodic in time, and a medium made up of a matrix with a dilute concentration of spherical inclusions. In the common quasi-steady approximation, Kef is equal to the classical steady solution while Sef = SA, the arithmetic mean. We derive expressions for the frequency dependent Kef, Sef, which are generally complex, i.e., dynamic. The main result is the delineation of the ranges of the parameters: dimensionless frequency (ω) and contrasts of conductivity (κ) and storativity (s) between the matrix and the inclusions, for which dynamic effects are significant.

A rational approach to improving productivity in recombinant Pichia pastoris fermentation.

PubMed

d'Anjou, M C; Daugulis, A J

2001-01-05

A Mut(S) Pichia pastoris strain that had been genetically modified to produce and secrete sea raven antifreeze protein was used as a model system to demonstrate the implementation of a rational, model-based approach to improve process productivity. A set of glycerol/methanol mixed-feed continuous stirred-tank reactor (CSTR) experiments was performed at the 5-L scale to characterize the relationship between the specific growth rate and the cell yield on methanol, the specific methanol consumption rate, the specific recombinant protein formation rate, and the productivity based on secreted protein levels. The range of dilution rates studied was 0. 01 to 0.10 h(-1), and the residual methanol concentration was kept constant at approximately 2 g/L (below the inhibitory level). With the assumption that the cell yield on glycerol was constant, the cell yield on methanol increased from approximately 0.5 to 1.5 over the range studied. A maximum specific methanol consumption rate of 20 mg/g. h was achieved at a dilution rate of 0.06 h(-1). The specific product formation rate and the volumetric productivity based on product continued to increase over the range of dilution rates studied, and the maximum values were 0.06 mg/g. h and 1.7 mg/L. h, respectively. Therefore, no evidence of repression by glycerol was observed over this range, and operating at the highest dilution rate studied maximized productivity. Fed-batch mass balance equations, based on Monod-type kinetics and parameters derived from data collected during the CSTR work, were then used to predict cell growth and recombinant protein production and to develop an exponential feeding strategy using two carbon sources. Two exponential fed-batch fermentations were conducted according to the predicted feeding strategy at specific growth rates of 0.03 h(-1) and 0.07 h(-1) to verify the accuracy of the model. Cell growth was accurately predicted in both fed-batch runs; however, the model underestimated recombinant product concentration. The overall volumetric productivity of both runs was approximately 2.2 mg/L. h, representing a tenfold increase in the productivity compared with a heuristic feeding strategy. Copyright 2001 John Wiley & Sons, Inc.

Is education associated with improvements in general cognitive ability, or in specific skills?

PubMed

Ritchie, Stuart J; Bates, Timothy C; Deary, Ian J

2015-05-01

Previous research has indicated that education influences cognitive development, but it is unclear what, precisely, is being improved. Here, we tested whether education is associated with cognitive test score improvements via domain-general effects on general cognitive ability (g), or via domain-specific effects on particular cognitive skills. We conducted structural equation modeling on data from a large (n = 1,091), longitudinal sample, with a measure of intelligence at age 11 years and 10 tests covering a diverse range of cognitive abilities taken at age 70. Results indicated that the association of education with improved cognitive test scores is not mediated by g, but consists of direct effects on specific cognitive skills. These results suggest a decoupling of educational gains from increases in general intellectual capacity. (c) 2015 APA, all rights reserved).

Empirical likelihood-based confidence intervals for the sensitivity of a continuous-scale diagnostic test at a fixed level of specificity.

PubMed

Gengsheng Qin; Davis, Angela E; Jing, Bing-Yi

2011-06-01

For a continuous-scale diagnostic test, it is often of interest to find the range of the sensitivity of the test at the cut-off that yields a desired specificity. In this article, we first define a profile empirical likelihood ratio for the sensitivity of a continuous-scale diagnostic test and show that its limiting distribution is a scaled chi-square distribution. We then propose two new empirical likelihood-based confidence intervals for the sensitivity of the test at a fixed level of specificity by using the scaled chi-square distribution. Simulation studies are conducted to compare the finite sample performance of the newly proposed intervals with the existing intervals for the sensitivity in terms of coverage probability. A real example is used to illustrate the application of the recommended methods.

Regression model development and computational procedures to support estimation of real-time concentrations and loads of selected constituents in two tributaries to Lake Houston near Houston, Texas, 2005-9

USGS Publications Warehouse

Lee, Michael T.; Asquith, William H.; Oden, Timothy D.

2012-01-01

In December 2005, the U.S. Geological Survey (USGS), in cooperation with the City of Houston, Texas, began collecting discrete water-quality samples for nutrients, total organic carbon, bacteria (Escherichia coli and total coliform), atrazine, and suspended sediment at two USGS streamflow-gaging stations that represent watersheds contributing to Lake Houston (08068500 Spring Creek near Spring, Tex., and 08070200 East Fork San Jacinto River near New Caney, Tex.). Data from the discrete water-quality samples collected during 2005–9, in conjunction with continuously monitored real-time data that included streamflow and other physical water-quality properties (specific conductance, pH, water temperature, turbidity, and dissolved oxygen), were used to develop regression models for the estimation of concentrations of water-quality constituents of substantial source watersheds to Lake Houston. The potential explanatory variables included discharge (streamflow), specific conductance, pH, water temperature, turbidity, dissolved oxygen, and time (to account for seasonal variations inherent in some water-quality data). The response variables (the selected constituents) at each site were nitrite plus nitrate nitrogen, total phosphorus, total organic carbon, E. coli, atrazine, and suspended sediment. The explanatory variables provide easily measured quantities to serve as potential surrogate variables to estimate concentrations of the selected constituents through statistical regression. Statistical regression also facilitates accompanying estimates of uncertainty in the form of prediction intervals. Each regression model potentially can be used to estimate concentrations of a given constituent in real time. Among other regression diagnostics, the diagnostics used as indicators of general model reliability and reported herein include the adjusted R-squared, the residual standard error, residual plots, and p-values. Adjusted R-squared values for the Spring Creek models ranged from .582–.922 (dimensionless). The residual standard errors ranged from .073–.447 (base-10 logarithm). Adjusted R-squared values for the East Fork San Jacinto River models ranged from .253–.853 (dimensionless). The residual standard errors ranged from .076–.388 (base-10 logarithm). In conjunction with estimated concentrations, constituent loads can be estimated by multiplying the estimated concentration by the corresponding streamflow and by applying the appropriate conversion factor. The regression models presented in this report are site specific, that is, they are specific to the Spring Creek and East Fork San Jacinto River streamflow-gaging stations; however, the general methods that were developed and documented could be applied to most perennial streams for the purpose of estimating real-time water quality data.

The influence of types of war experiences on conduct problems in war-affected youth in Northern Ugandan: Findings from the WAYS study.

PubMed

Amone-P Olak, Kennedy; Ovuga, Emilio

2017-05-01

Exposure to war is associated with poor psychosocial outcomes. Yet the effects of different types of war events on various psychosocial outcomes such as conduct problems remain unknown. This study aims to assess whether various war events differ in predicting conduct problems. Using data from an on-going longitudinal research project, the WAYS study, the current article examined the relationship between specific war events and conduct problems in war-affected youth in Northern Uganda (N=539, baseline age=22.39; SD=2.03, range 18-25). Regression analyses were conducted to relate each type of war experience to conduct problems. War categories of "witnessing violence", "deaths", "threat to loved ones" and "sexual abuse" were associated with reporting conduct problems. Multivariable models yielded independent effects of ''witnessing violence'' (β=0.09, 95% CI: 0.01, 0.18) and ''Sexual abuse'' (β=0.09, 95% CI: 0.02, 0.19) on conduct problems while "duration in captivity" independently and negatively predicted conduct problems (β=-0.14, 95% CI: -0.23, -0.06). Types of war events vary in predicting conduct problems and should be considered when designing interventions to alleviate negative consequences of exposure to war. Moreover, longer duration in captivity appear to protect war-affected youth from conduct problems. Copyright © 2017 Elsevier Ireland Ltd. All rights reserved.

The influence of types of war experiences on conduct problems in war-affected youth in Northern Ugandan: Findings from the WAYS study

PubMed Central

Amone-P′Olak, Kennedy; Ovuga, Emilio

2017-01-01

Exposure to war is associated with poor psychosocial outcomes. Yet the effects of different types of war events on various psychosocial outcomes such as conduct problems remain unknown. This study aims to assess whether various war events differ in predicting conduct problems. Using data from an on-going longitudinal research project, the WAYS study, the current article examined the relationship between specific war events and conduct problems in war-affected youth in Northern Uganda (N=539, baseline age=22.39; SD=2.03, range 18– 25). Regression analyses were conducted to relate each type of war experience to conduct problems. War categories of “witnessing violence”, “deaths”, “threat to loved ones” and “sexual abuse” were associated with reporting conduct problems. Multivariable models yielded independent effects of “witnessing violence” (β=0.09, 95% CI: 0.01, 0.18) and “Sexual abuse” (β=0.09, 95% CI: 0.02, 0.19) on conduct problems while “duration in captivity” independently and negatively predicted conduct problems (β=−0.14, 95% CI: −0.23, −0.06). Types of war events vary in predicting conduct problems and should be considered when designing interventions to alleviate negative consequences of exposure to war. Moreover, longer duration in captivity appear to protect war-affected youth from conduct problems. PMID:28171768

Ecological differentiation within a cosmopolitan group of planktonic freshwater bacteria (SOL cluster, Saprospiraceae, Bacteroidetes).

PubMed

Schauer, Michael; Kamenik, Christian; Hahn, Martin W

2005-10-01

Members of the monophyletic SOL cluster are large filamentous bacteria inhabiting the pelagic zone of many freshwater habitats. The abundances of SOL bacteria and compositions of SOL communities in samples from 115 freshwater ecosystems around the globe were determined by fluorescence in situ hybridization with cluster- and subcluster-specific oligonucleotide probes. The vast majority (73%) of sampled ecosystems harbored SOL bacteria, and all three previously described SOL subclusters (LD2, HAL, and GKS2-217) were detected. The morphometric and chemicophysical parameters and trophic statuses of ecosystems were related to the occurrence and subcluster-specific composition of SOL bacteria by multivariate statistical methods. SOL bacteria did not occur in acidic lakes (pH < 6), and their abundance was negatively related to high trophy and pH. The subcluster-specific variation in the compositions of SOL communities could be related to the pH, electrical conductivity, altitude, and trophic status of ecosystems. All three known SOL subclusters differed in respect to their tolerated ranges of pH and conductivity. Complete niche separation was observed between the vicarious subclusters GKS2-217 and LD2; the former occurred in soft-water lakes, whereas the latter was found in a broad range of hard-water habitats. The third subgroup (HAL) showed a wide environmental tolerance and was usually found sympatrically with the LD2 or GKS2-217 subcluster. Ecological differentiation of SOL bacteria at the subcluster level was most probably driven by differential adaptation to water chemistry. The distribution of the two vicarious taxa seems to be predominantly controlled by the geological backgrounds of the catchment areas of the habitats.

The impact of Dupuytren disease on patient activity and quality of life.

PubMed

Wilburn, J; McKenna, S P; Perry-Hinsley, D; Bayat, A

2013-06-01

To explore the impact of Dupuytren disease (DD) from the patients' perspective. Audio-recorded interviews were conducted for patients with Dupuytren disease (DD) attending outpatient clinics. The interviews were transcribed and subjected to content analysis. This analysis highlighted key impact areas and common themes in individuals' personal experiences. These were then allocated to categories specified by the World Health Organization International Classification of Functioning, Disability, and Health (impairments and activity limitations) and the needs-based model of quality of life (QoL). Qualitative unstructured interviews were conducted with 34 patients (74% men; age, 41-80 y; mean [SD], 64 [13] y). The sample had a wide range of severity and duration of DD (range, 0.5-40; mean [SD], 13 [10] y). Nine hundred fifty-three statements relating to the impact of DD were identified from the interview transcripts. These statements fell into 2 major categories of impact: activity limitations (10 themes including problems with dressing, gripping, and personal care) and QoL (6 need categories: physiological, safety and security, social, affection, esteem, and cognitive needs). Findings from the interviews suggest that DD affects both performance of activities and QoL. To determine accurately the effectiveness of DD interventions from the patients' perspective, it is important to determine their impacts on both activity limitations and QoL. We intend to develop valid, reproducible, and responsive DD-specific scales for this purpose. The study identifies key issues specific to DD that influence patients' functioning and QoL. The information reported will form the basis of DD-specific patient-reported outcomes measures for use in clinical practice and evaluations of interventions. Copyright © 2013 American Society for Surgery of the Hand. Published by Elsevier Inc. All rights reserved.

Ammonia Monitor

NASA Technical Reports Server (NTRS)

Sauer, Richard L. (Inventor); Akse, James R. (Inventor); Thompson, John O. (Inventor); Atwater, James E. (Inventor)

1999-01-01

Ammonia monitor and method of use are disclosed. A continuous, real-time determination of the concentration of ammonia in an aqueous process stream is possible over a wide dynamic range of concentrations. No reagents are required because pH is controlled by an in-line solid-phase base. Ammonia is selectively transported across a membrane from the process stream to an analytical stream to an analytical stream under pH control. The specific electrical conductance of the analytical stream is measured and used to determine the concentration of ammonia.

Determination of Selection Criteria for Spray Drift Reduction from Atomization Data

DTIC Science & Technology

2012-01-01

Solutions Testing was conducted using glyphosate (Roundup PowerMAX, EPA Reg. No. 524–549, Monsanto Company, St. Louis, MO) as the active ingredient...This po- tassium glyphosate contains 540 g acid equivalent glyphosate per liter and is sprayed at 1.6 l/hectare (22 oz/acre), yielding a 1.7 % v/v...Table 1) were tested in water only and in water plus the glyphosate . The specific polymers were chosen so as to cre- ate a range of solutions with and

Preparation Torque Limit for Composites Joined with Mechanical Fasteners

NASA Technical Reports Server (NTRS)

Thomas, Frank P.; Yi, Zhao

2005-01-01

Current design guidelines for determining torque ranges for composites are based on tests and analysis from isotropic materials. Properties of composites are not taken into account. No design criteria based upon a systematic analytical and test analyses is available. This paper is to study the maximum torque load a composite component could carry prior to any failure. Specifically, the torque-tension tests are conducted. NDT techniques including acoustic emission, thermography and photomicroscopy are also utilized to characterize the damage modes.

Global satellite triangulation and trilateration for the National Geodetic Satellite Program (solutions WN 12, 14 and 16). [study and analysis of data from artificial satellites

NASA Technical Reports Server (NTRS)

Mueller, I. I.; Kumar, M.; Reilly, J. P.; Saxena, N.; Soler, T.

1973-01-01

A multi-year study and analysis of data from satellites launched specifically for geodetic purposes and from other satellites useful in geodetic studies was conducted. The program of work included theoretical studies and analysis for the geometric determination of station positions derived from photographic observations of both passive and active satellites and from range observations. The current status of data analysis, processing and results are examined.

Summary of a Workshop on Plant Canopy Structure, 27-30 April 1981, Oak Ridge, Tennessee.

DTIC Science & Technology

1982-08-01

relating canopy structure to amounts of water-conducting tissue have mostly been tried for woody trees and shrubs in which sapwood area is used as...Forest Service. 20 pp. Grier, C. C. and R. H. Waring. 1974. Conifer foliage mass related to sapwood area . Forest Sci. 20:205-206. Hallg, F., R. A. A...Plant Canopy Struc- ture was held at Oak Ridge, Tenn. Over 30 individuals representing a broad range of disciplines and specific areas of expertise were

The design and operating characteristics of an advanced 30-kW ammonia arcjet engine

NASA Technical Reports Server (NTRS)

Deininger, William D.; Pivirotto, Thomas J.; Brophy, John R.

1987-01-01

Experimental investigations were conducted to evaluate the effects of a contoured nozzle and modified cathode shape on ammonia arcjet engine performance. The contoured nozzle performance data were compared to the performance data of an arcjet which had a 38-deg included-angle, conical nozzle. Thrust improvements of up to 10 percent were demonstrated which corresponded to 3 percent improvements in specific impulse and 10 percent improvements in thrust efficiency. Performance characterizations for the modified cathode tip were conducted with the contoured nozzle arcjet. A uniform 15 percent decrease in arc voltage was demonstrated over a mass flow range of 0.175 to 0.350 g/s. A 4 percent improvement in thrust efficiency was noted at 22.0 kW.

A theoretical analysis of vacuum arc thruster performance

NASA Technical Reports Server (NTRS)

Polk, James E.; Sekerak, Mike; Ziemer, John K.; Schein, Jochen; Qi, Niansheng; Binder, Robert; Anders, Andre

2001-01-01

In vacuum arc discharges the current is conducted through vapor evaporated from the cathode surface. In these devices very dense, highly ionized plasmas can be created from any metallic or conducting solid used as the cathode. This paper describes theoretical models of performance for several thruster configurations which use vacuum arc plasma sources. This analysis suggests that thrusters using vacuum arc sources can be operated efficiently with a range of propellant options that gives great flexibility in specific impulse. In addition, the efficiency of plasma production in these devices appears to be largely independent of scale because the metal vapor is ionized within a few microns of the cathode electron emission sites, so this approach is well-suited for micropropulsion.

Conducting Polymers for Neural Prosthetic and Neural Interface Applications

PubMed Central

2015-01-01

Neural interfacing devices are an artificial mechanism for restoring or supplementing the function of the nervous system lost as a result of injury or disease. Conducting polymers (CPs) are gaining significant attention due to their capacity to meet the performance criteria of a number of neuronal therapies including recording and stimulating neural activity, the regeneration of neural tissue and the delivery of bioactive molecules for mediating device-tissue interactions. CPs form a flexible platform technology that enables the development of tailored materials for a range of neuronal diagnostic and treatment therapies. In this review the application of CPs for neural prostheses and other neural interfacing devices are discussed, with a specific focus on neural recording, neural stimulation, neural regeneration, and therapeutic drug delivery. PMID:26414302

Design and Performance Estimates of an Ablative Gallium Electromagnetic Thruster

NASA Technical Reports Server (NTRS)

Thomas, Robert E.

2012-01-01

The present study details the high-power condensable propellant research being conducted at NASA Glenn Research Center. The gallium electromagnetic thruster is an ablative coaxial accelerator designed to operate at arc discharge currents in the range of 10-25 kA. The thruster is driven by a four-parallel line pulse forming network capable of producing a 250 microsec pulse with a 60 kA amplitude. A torsional-type thrust stand is used to measure the impulse of a coaxial GEM thruster. Tests are conducted in a vacuum chamber 1.5 m in diameter and 4.5 m long with a background pressure of 2 microtorr. Electromagnetic scaling calculations predict a thruster efficiency of 50% at a specific impulse of 2800 seconds.

Investigation of charge dissipation in jet fuel in a dielectric fuel tank

NASA Astrophysics Data System (ADS)

Kitanin, E. L.; Kravtsov, P. A.; Trofimov, V. A.; Kitanina, E. E.; Bondarenko, D. A.

2017-09-01

The electrostatic charge dissipation process in jet fuel in a polypropylene tank was investigated experimentally. Groundable metallic terminals were installed in the tank walls to accelerate the dissipation process. Several sensors and an electrometer with a current measuring range from 10-11 to 10-3 A were specifically designed to study the dissipation rates. It was demonstrated that thanks to the sensors and the electrometer one can obtain reliable measurements of the dissipation rate and look at how it is influenced by the number and locations of the terminals. Conductivity of jet fuel and effective conductivity of the tank walls were investigated in addition. The experimental data agree well with the numerical simulation results obtained using COMSOL software package.

Carrier Transport and Effective Barrier Height of Low Resistance Metal Contact to Highly Mg-Doped p-GaN

NASA Astrophysics Data System (ADS)

Park, Youngjun; Kim, Hyunsoo

2011-08-01

The effective barrier height and carrier transport mechanism of low resistance Ag-based contact to highly Mg-doped p-GaN were investigated. The specific contact resistance obtained was as low as 7.0×10-4 Ω cm2. The electrical resistivity of p-GaN was found to increase depending on ˜T-1/4, indicating variable-range hopping (VRH) conduction through Mg-related deep-level defects. Based on the VRH conduction model, the effective barrier height for carrier transport could be measured as 0.12 eV, which is low enough to explain the formation of excellent ohmic contact. The deep-level defects were also found to induce surface Fermi pinning.

High Conductivity Carbon-Carbon Heat Pipes for Light Weight Space Power System Radiators

NASA Technical Reports Server (NTRS)

Juhasz, Albert J.

2008-01-01

Based on prior successful fabrication and demonstration testing of a carbon-carbon heat pipe radiator element with integral fins this paper examines the hypothetical extension of the technology via substitution of high thermal conductivity composites which would permit increasing fin length while still maintaining high fin effectiveness. As a result the specific radiator mass could approach an ultimate asymptotic minimum value near 1.0 kg/m2, which is less than one fourth the value of present day satellite radiators. The implied mass savings would be even greater for high capacity space and planetary surface power systems, which may require radiator areas ranging from hundreds to thousands of square meters, depending on system power level.

Relationship of Shallow Groundwater Quality to Hydraulic Fracturing Activities in Antrim and Kalkaska Counties, MI

NASA Astrophysics Data System (ADS)

Stefansky, J. N.; Robertson, W. M.; Chappaz, A.; Babos, H.; Israel, S.; Groskreutz, L. M.

2015-12-01

Hydraulic fracturing (fracking) of oil and natural gas (O&G) wells is a widely applied technology that can increase yields from tight geologic formations. However, it is unclear how fracking may impact shallow groundwater; previous research into its effects has produced conflicting results. Much of the worry over potential impacts to water quality arises from concerns about the produced water. The water produced from O&G formations is often salty, contains toxic dissolved elements, and can be radioactive. If fracking activities cause or increase connectivity between O&G formations and overlying groundwater, there may be risks to aquifers. As one part of a groundwater quality study in Antrim and Kalkaska Counties, MI, samples were collected from the unconfined glacial aquifer (3-300 m thick) and produced water from the underlying Antrim formation, a shallow (180-670 m deep) natural gas producing black shale. Groundwater samples were collected between 200 to 10,000 m distance from producing Antrim gas wells and from a range of screened intervals (15-95 m). Samples were analyzed for major constituents (e.g., Br, Cl), pH, conductivity, and dissolved oxygen (DO). The specific conductance of groundwater samples ranged from 230-1020 μS/cm; DO ranged from 0.4-100% saturation. Preliminary results show a slight inverse correlation between specific conductance and proximity to producing Antrim wells. The observed range of DO saturation in glacial aquifer groundwater appears to be related to both screened depth of the water wells and proximity to Antrim wells. During sampling, some well owners expressed concerns about the effects of fracking on groundwater quality and reported odd smells and tastes in their water after O&G drilling occurred near their homes. The results of this study and reported observations provide evidence to suggest a potential hydrogeological connection between the Antrim formation and the overlying glacial aquifer in some locations; it also raises questions about water quality in Antrim and Kalkaska counties. Further investigation is needed to address questions raised in this study. As the controversy surrounding fracking is growing and the application of this technology spreads worldwide, it is important for the questions about fracking and groundwater quality to be well addressed.

Hydraulic efficiency and safety of branch xylem increases with height in Sequoia sempervirens (D. Don) crowns.

PubMed

Burgess, Stephen S O; Pittermann, Jarmila; Dawson, Todd E

2006-02-01

The hydraulic limitation hypothesis of Ryan & Yoder (1997, Bioscience 47, 235-242) suggests that water supply to leaves becomes increasingly difficult with increasing tree height. Within the bounds of this hypothesis, we conjectured that the vertical hydrostatic gradient which gravity generates on the water column in tall trees would cause a progressive increase in xylem 'safety' (increased resistance to embolism and implosion) and a concomitant decrease in xylem 'efficiency' (decreased hydraulic conductivity). We based this idea on the historically recognized concept of a safety-efficiency trade-off in xylem function, and tested it by measuring xylem conductivity and vulnerability to embolism of Sequoia sempervirens branches collected at a range of heights. Measurements of resistance of branch xylem to embolism did indeed show an increase in 'safety' with height. However, the expected decrease in xylem 'efficiency' was not observed. Instead, sapwood-specific hydraulic conductivities (Ks) of branches increased slightly, while leaf-specific hydraulic conductivities increased dramatically, with height. The latter could be largely explained by strong vertical gradients in specific leaf area. The increase in Ks with height corresponded to a decrease in xylem wall fraction (a measure of wall thickness), an increase in percentage of earlywood and slight increases in conduit diameter. These changes are probably adaptive responses to the increased transport requirements of leaves growing in the upper canopy where evaporative demand is greater. The lack of a safety-efficiency tradeoff may be explained by opposing height trends in the pit aperture and conduit diameter of tracheids and the major and semi-independent roles these play in determining xylem safety and efficiency, respectively.

Atomistic characterisation of Li+ mobility and conductivity in Li(7-x)PS(6-x)Ix argyrodites from molecular dynamics simulations, solid-state NMR, and impedance spectroscopy.

PubMed

Pecher, Oliver; Kong, Shiao-Tong; Goebel, Thorsten; Nickel, Vera; Weichert, Katja; Reiner, Christof; Deiseroth, Hans-Jörg; Maier, Joachim; Haarmann, Frank; Zahn, Dirk

2010-07-26

The atomistic mechanisms of Li(+) ion mobility/conductivity in Li(7-x)PS(6-x)I(x) argyrodites are explored from both experimental and theoretical viewpoints. Ionic conductivity in the title compound is associated with a solid-solid phase transition, which was characterised by low-temperature differential scanning calorimetry, (7)Li and (127)I NMR investigations, impedance measurements and molecular dynamics simulations. The NMR signals of both isotopes are dominated by anisotropic interactions at low temperatures. A significant narrowing of the NMR signal indicates a motional averaging of the anisotropic interactions above 177+/-2 K. The activation energy to ionic conductivity was assessed from both impedance spectroscopy and molecular dynamics simulations. The latter revealed that a series of interstitial sites become accessible to the Li(+) ions, whilst the remaining ions stay at their respective sites in the argyrodite lattice. The interstitial positions each correspond to the centres of tetrahedra of S/I atoms, and differ only in terms of their common corners, edges, or faces with adjacent PS(4) tetrahedra. From connectivity analyses and free-energy rankings, a specific tetrahedron is identified as the key restriction to ionic conductivity, and is clearly differentiated from local mobility, which follows a different mechanism with much lower activation energy. Interpolation of the lattice parameters as derived from X-ray diffraction experiments indicates a homogeneity range for Li(7-x)PS(6-x)I(x) with 0.97 < or = x < or = 1.00. Within this range, molecular dynamics simulations predict Li(+) conductivity at ambient conditions to vary considerably.

Effects of Urban Development on Water-Quality in the Piedmont of North Carolina-- The NAWQA Urban Land-Use Gradient Study

NASA Astrophysics Data System (ADS)

Harned, D. A.; Cuffney, T. F.; Giddings, E. M.; McMahon, G.

2004-12-01

A study of urban basins located in the Piedmont of North Carolina is underway as part of the U. S. Geological Survey National Water-Quality Assessment (NAWQA) to determine the relation between level of urban development and water quality. Data were collected from 30 basins on water chemistry (nutrient, pesticide, and ion concentrations), geomorphic and habitat characteristics, hydrologic stage, discharge, water temperature, pH, dissolved-oxygen concentration, specific conductance, benthic algae, invertebrate communities, and fish communities. Collection frequency for water chemistry ranged from 2 samples (at 20 sites) to 6 samples (at 10 sites). Biological data were collected in each basin twice. Investigation of the effects of urbanization on water quality must control for the effects of natural factors, while varying the degree of urbanization between study basins. A regional framework was used to control variability in natural factors that influence water-quality. The urban intensity in each basin was measured by using an index to integrate information on human influences. The Urban Index includes information about land cover, infrastructure, population, and socioeconomic characteristics. Sites were selected to represent the full gradient of undeveloped to fully urbanized basins. A preliminary review of the stream water-chemistry data indicates distinct relations between ionic composition and the Urban Index. Mean specific conductance was positively correlated with the Urban Index (Spearman correlation coefficient (r) = 0.77; 95-percent confidence limits (95CL) 0.61 - 0.93; probability (pr) <0.0001; N=30). Specific conductance ranged from 56 microsiemens (uS) at the least developed site to 607 uS at the most developed site. Dissolved sulfate (r=0.74; 95CL 0.57 - 0.91; pr <0.0001) and chloride (r=0.71; 95CL 0.52 - 0.90; pr <0.0001) were also positively correlated with the Urban Index. Sulfate ranged from 2.3 to 66 milligrams per liter (mg/L), and chloride ranged from 3.5 to 96 mg/L. Urban sources of sulfate include domestic sewage and emissions from the combustion of automotive and diesel fuels. Sources of chloride include sewage and road salting. pH was positively correlated with the Urban Index (r=0.60; 95CL 0.38 - 0.84; pr= 0.0005) with a range from 6.5 at the least urban site to 7.5 at the most urban site. The increase in pH may be due in part to conversion of organic forest soils to less acidic soils of urban lawns. The overall trend of increasing total dissolved nitrogen (r=0.46; 95CL 0.12 - 0.80; pr=0.0103) and nitrite plus nitrate (r=0.46; 95CL 0.09 - 0.83; pr=0.0109) concentrations, with increasing Urban Index may reflect sources such as sewage and lawn fertilizer use in the more urban basins. However, some of the least urban basins also had elevated nitrogen concentrations reflecting possible agricultural influences such as fertilizer use and animal waste. Total nitrogen concentration ranged from 0.31 to 14 mg/L. Unit-area stream discharge during low-flow periods was negatively correlated with the Urban Index (r= -0.56; 95CL -0.74 - -0.37; pr=0.0014). Reduced discharge with greater urban development may be a result of reduced infiltration caused by impervious surfaces. Unit discharge ranged from 0.47 to 2.27 cubic feet per second per square mile of drainage area.

Comparison of high temperature, high frequency core loss and dynamic B-H loops of a 2V-49Fe-49Co and a grain oriented 3Si-Fe alloy

NASA Technical Reports Server (NTRS)

Wieserman, W. R.; Schwarze, G. E.; Niedra, J. M.

1992-01-01

The design of power magnetic components such as transformers, inductors, motors, and generators, requires specific knowledge about the magnetic and electrical characteristics of the magnetic materials used in these components. Limited experimental data exists that characterizes the performance of soft magnetic materials for the combined conditions of high temperature and high frequency over a wide flux density range. An experimental investigation of a 2V-49-Fe-49Co (Supermendur) and a grain oriented 3 Si-Fe (Magnesil) alloy was conducted over the temperature range of 23 to 300 C and frequency range of 0.1 to 10 kHz. The effects of temperature, frequency, and maximum flux density on the core loss and dynamic B-H loops for sinusoidal voltage excitation conditions are examined for each of these materials. A comparison of the core loss of these two materials is also made over the temperature and frequency range investigated.

Sensitivity and specificity of the method used for ascertainment of healthcare-associated infections in the second Slovenian national prevalence survey.

PubMed

Serdt, Mojca; Lejko Zupanc, Tatjana; Korošec, Aleš; Klavs, Irena

2016-12-01

The second Slovenian national healthcare-associated infections (HAIs) prevalence survey (SNHPS) was conducted in acute-care hospitals in 2011. The objective was to assess the sensitivity and specificity of the method used for the ascertainment of six types of HAIs (bloodstream infections, catheter-associated infections, lower respiratory tract infections, pneumoniae, surgical site infections, and urinary tract infections) in the University Medical Centre Ljubljana (UMCL). A cross-sectional study was conducted in patients surveyed in the SNHPS in the UMCL using a retrospective medical chart review (RMCR) and European HAIs surveillance definitions. Sensitivity and specificity of the method used in the SNHPS using RMCR as a reference was computed for ascertainment of patients with any of the six selected types of HAIs and for individual types of HAIs. Agreement between the SNHPS and RMCR results was analyzed using Cohen's kappa coefficient. 1474 of 1742 (84.6%) patients surveyed in the SNHPS were included in RMCR. The sensitivity of the SNHPS method for detecting any of six HAIs was 90% (95% confidence interval (CI): 81%-95%) and specificity 99% (95% CI: 98%-99%). The sensitivity by type of HAI ranged from 63% (lower respiratory tract infections) to 92% (bloodstream infections). Specificity was at least 99% for all types of HAIs. Agreement between the two data collection approaches for HAIs overall was very good (κ=0.83). The overall sensitivity of SNHPS collection method for ascertaining HAIs overall was high and the specificity was very high. This suggests that the estimated prevalence of HAIs in the SNHPS was credible.

Room temperature thermal conductivity measurements of neat MOF-5 compacts with high pressure hydrogen and helium

DOE PAGES

Semelsberger, Troy Allen; Veenstra, Mike; Dixon, Craig

2016-02-09

Metal-organic frameworks (MOFs) are a highly porous crystalline material with potential in various applications including on-board vehicle hydrogen storage for fuel cell vehicles. The thermal conductivity of MOFs is an important parameter in the design and ultimate performance of an on-board hydrogen storage system. However, in-situ thermal conductivity measurements have not been previously reported. The present study reports room temperature thermal conductivity and thermal diffusivity measurements performed on neat MOF-5 cylindrical compacts (ρ = 0.4 g/mL) as a function of pressure (0.27–90 bar) and gas type (hydrogen and helium). The transient plane source technique was used to measure both themore » non-directional thermal properties (isotropic method) and the directional thermal properties (anisotropic method). High pressure measurements were made using our in-house built low-temperature, high pressure thermal conductivity sample cell. The intrinsic thermal properties of neat MOF-5 measured under vacuum were—Isotropic: k isotropic = 0.1319 W/m K, α isotropic = 0.4165 mm 2/s; Anisotropic: k axial = 0.1477 W/m K, k radial = 0.1218 W/m K, α axial = 0.5096 mm 2/s, and α radial = 0.4232 mm 2/s. The apparent thermal properties of neat MOF-5 increased with increasing hydrogen and helium pressure, with the largest increase occurring in the narrow pressure range of 0–10 bar and then monotonically asymptoting with increasing pressures up to around 90 bar. On average, a greater than two-fold enhancement in the apparent thermal properties was observed with neat MOF-5 in the presence of helium and hydrogen compared to the intrinsic values of neat MOF-5 measured under vacuum. The apparent thermal properties of neat MOF-5 measured with hydrogen were higher than those measured with helium, which were directly related to the gas-specific thermal properties of helium and hydrogen. Neat MOF-5 exhibited a small degree of anisotropy under all conditions measured with thermal conductivities and diffusivities in the axial direction being higher than those in the radial direction. As a result, the low temperature specific heat capacities of neat MOF-5 were also measured and reported for the temperature range of 93–313 K (–180–40 °C).« less

Room temperature thermal conductivity measurements of neat MOF-5 compacts with high pressure hydrogen and helium

DOE Office of Scientific and Technical Information (OSTI.GOV)

Semelsberger, Troy Allen; Veenstra, Mike; Dixon, Craig

Metal-organic frameworks (MOFs) are a highly porous crystalline material with potential in various applications including on-board vehicle hydrogen storage for fuel cell vehicles. The thermal conductivity of MOFs is an important parameter in the design and ultimate performance of an on-board hydrogen storage system. However, in-situ thermal conductivity measurements have not been previously reported. The present study reports room temperature thermal conductivity and thermal diffusivity measurements performed on neat MOF-5 cylindrical compacts (ρ = 0.4 g/mL) as a function of pressure (0.27–90 bar) and gas type (hydrogen and helium). The transient plane source technique was used to measure both themore » non-directional thermal properties (isotropic method) and the directional thermal properties (anisotropic method). High pressure measurements were made using our in-house built low-temperature, high pressure thermal conductivity sample cell. The intrinsic thermal properties of neat MOF-5 measured under vacuum were—Isotropic: k isotropic = 0.1319 W/m K, α isotropic = 0.4165 mm 2/s; Anisotropic: k axial = 0.1477 W/m K, k radial = 0.1218 W/m K, α axial = 0.5096 mm 2/s, and α radial = 0.4232 mm 2/s. The apparent thermal properties of neat MOF-5 increased with increasing hydrogen and helium pressure, with the largest increase occurring in the narrow pressure range of 0–10 bar and then monotonically asymptoting with increasing pressures up to around 90 bar. On average, a greater than two-fold enhancement in the apparent thermal properties was observed with neat MOF-5 in the presence of helium and hydrogen compared to the intrinsic values of neat MOF-5 measured under vacuum. The apparent thermal properties of neat MOF-5 measured with hydrogen were higher than those measured with helium, which were directly related to the gas-specific thermal properties of helium and hydrogen. Neat MOF-5 exhibited a small degree of anisotropy under all conditions measured with thermal conductivities and diffusivities in the axial direction being higher than those in the radial direction. As a result, the low temperature specific heat capacities of neat MOF-5 were also measured and reported for the temperature range of 93–313 K (–180–40 °C).« less

The Application of EM38: Determination of Soil Parameters, Selection of Soil Sampling Points and Use in Agriculture and Archaeology

PubMed Central

Heil, Kurt

2017-01-01

Fast and accurate assessment of within-field variation is essential for detecting field-wide heterogeneity and contributing to improvements in the management of agricultural lands. The goal of this paper is to provide an overview of field scale characterization by electromagnetic induction, firstly with a focus on the applications of EM38 to salinity, soil texture, water content and soil water turnover, soil types and boundaries, nutrients and N-turnover and soil sampling designs. Furthermore, results concerning special applications in agriculture, horticulture and archaeology are included. In addition to these investigations, this survey also presents a wide range of practical methods for use. Secondly, the effectiveness of conductivity readings for a specific target in a specific locality is determined by the intensity at which soil factors influence these values in relationship to the desired information. The interpretation and utility of apparent electrical conductivity (ECa) readings are highly location- and soil-specific, so soil properties influencing the measurement of ECa must be clearly understood. From the various calibration results, it appears that regression constants for the relationships between ECa, electrical conductivity of aqueous soil extracts (ECe), texture, yield, etc., are not necessarily transferable from one region to another. The modelling of ECa, soil properties, climate and yield are important for identifying the location to which specific utilizations of ECa technology (e.g., ECa−texture relationships) can be appropriately applied. In general, the determination of absolute levels of ECa is frequently not possible, but it appears to be quite a robust method to detect relative differences, both spatially and temporally. Often, the use of ECa is restricted to its application as a covariate or the use of the readings in a relative sense rather than as absolute terms. PMID:29113048

Biannual water-resources review, White Sands Missile Range, New Mexico, 1986 and 1987

USGS Publications Warehouse

Myers, Robert G.; Sharp, Steven C.

1989-01-01

Hydrologic data were collected at White Sands Missile Range, New Mexico in 1986 and 1987. The total groundwater withdrawal in 1986 was 565,462,500 gal and in 1987 it was 620,492,000 gal. The total groundwater withdrawal was 110,971,300 gal less in 1986 than in 1985, but 55,029,500 gal more in 1987 than in 1986. Water samples from five Post Headquarters water supply wells were collected for chemical analysis in 1986. In 1987, water samples were collected from four test wells in the Post Headquarters area for analysis of selected volatile organic compounds. Twenty-eight water samples from wells were collected for analysis of specific conductance in 1986 and 1987. (USGS)

Lewis Structures Technology, 1988. Volume 3: Structural Integrity Fatigue and Fracture Wind Turbines HOST

NASA Technical Reports Server (NTRS)

1988-01-01

The charter of the Structures Division is to perform and disseminate results of research conducted in support of aerospace engine structures. These results have a wide range of applicability to practioners of structural engineering mechanics beyond the aerospace arena. The specific purpose of the symposium was to familiarize the engineering structures community with the depth and range of research performed by the division and its academic and industrial partners. Sessions covered vibration control, fracture mechanics, ceramic component reliability, parallel computing, nondestructive evaluation, constitutive models and experimental capabilities, dynamic systems, fatigue and damage, wind turbines, hot section technology (HOST), aeroelasticity, structural mechanics codes, computational methods for dynamics, structural optimization, and applications of structural dynamics, and structural mechanics computer codes.

Proceedings of conference XXXII; workshop on Future directions in evaluating earthquake hazards of Southern California

USGS Publications Warehouse

Brown, William M.; Kockelman, William J.; Ziony, Joseph I.

1986-01-01

Hydrologic data were collected at White Sands Missile Range, NM, in 1985. The total groundwater withdrawal in 1985 was 676,433 ,800 gallons. The 11 supply wells in the Post Headquarters well field produced 642,056,000 gallons, or about 95 percent of the total. The six Range area supply wells produced 34,377,800 gallons. The total groundwater withdrawal was 8,841,200 gallons less in 1985 than 1984. Water samples from six Post Headquarters supply wells were collected for major chemical analysis. Water samples from 19 other wells were collected for pH and specific-conductance analysis. Depth-to-water measurements in the Post Headquarters supply wells showed seasonal fluctuations as well as continued long-term declines. (USGS)

Conceptual and numerical models of the glacial aquifer system north of Aberdeen, South Dakota

USGS Publications Warehouse

Marini, Katrina A.; Hoogestraat, Galen K.; Aurand, Katherine R.; Putnam, Larry D.

2012-01-01

This U.S. Geological Survey report documents a conceptual and numerical model of the glacial aquifer system north of Aberdeen, South Dakota, that can be used to evaluate and manage the city of Aberdeen's water resources. The glacial aquifer system in the model area includes the Elm, Middle James, and Deep James aquifers, with intervening confining units composed of glacial till. The Elm aquifer ranged in thickness from less than 1 to about 95 feet (ft), with an average thickness of about 24 ft; the Middle James aquifer ranged in thickness from less than 1 to 91 ft, with an average thickness of 13 ft; and the Deep James aquifer ranged in thickness from less than 1 to 165 ft, with an average thickness of 23 ft. The confining units between the aquifers consisted of glacial till and ranged in thickness from 0 to 280 ft. The general direction of groundwater flow in the Elm aquifer in the model area was from northwest to southeast following the topography. Groundwater flow in the Middle James aquifer was to the southeast. Sparse data indicated a fairly flat potentiometric surface for the Deep James aquifer. Horizontal hydraulic conductivity for the Elm aquifer determined from aquifer tests ranged from 97 to 418 feet per day (ft/d), and a confined storage coefficient was determined to be 2.4x10-5. Estimates of the vertical hydraulic conductivity of the sediments separating the Elm River from the Elm aquifer, determined from the analysis of temperature gradients, ranged from 0.14 to 2.48 ft/d. Average annual precipitation in the model area was 19.6 inches per year (in/yr), and agriculture was the primary land use. Recharge to the Elm aquifer was by infiltration of precipitation through overlying outwash, lake sediments, and glacial till. The annual recharge for the model area, calculated by using a soil-water-balance method for water year (WY) 1975-2009, ranged from 0.028 inch in WY 1980 to 4.52 inches in WY 1986, with a mean of 1.56 inches. The annual potential evapotranspiration, calculated in soil-water-balance analysis, ranged from 21.8 inches in WY 1983 to 27.0 inches in WY 1985, with a mean of 24.6 inches. Water use from the glacial aquifer system primarily was from the Elm aquifer for irrigation, municipal, and suburban water supplies, and the annual rate ranged from 1.0 to 2.4 cubic feet per second (ft3/s). The MODFLOW-2005 numerical model represented the Elm aquifer, the Middle James aquifer, and the Deep James aquifer with model layers 1-3 respectively separated by confining layers 1-2 respectively. Groundwater flow was simulated with 75 stress periods beginning October 1, 1974, and ending September 30, 2009. Model grid spacing was 200 by 200 ft and boundaries were represented by specified-head boundaries and no-flow boundaries. The model used parameter estimation that focused on minimizing the difference between 954 observed and simulated hydraulic heads for 135 wells. Calibrated mean horizontal hydraulic conductivity values for model layers 1-3 were 94, 41, and 30 ft/d respectively. Vertical hydraulic conductivity values for confining layers 1 and 2 were 0.0002 and 0.0003 ft/d, respectively. Calibrated specific yield for model layer 1was 0.1 and specific storage ranged from 0.0003 to 0.0005 per foot. Calibrated mean recharge rates ranged from 2.5 in/yr where glacial till thickness was less than 10 ft to 0.8 in/yr where glacial till thickness was greater than 30 ft. Calibrated mean annual evapotranspiration rate was 8.8 in/yr. Simulated net streamflow gain from model layer 1 was 3.1 ft3/s.

Neutron organ dose and the influence of adipose tissue

NASA Astrophysics Data System (ADS)

Simpkins, Robert Wayne

Neutron fluence to dose conversion coefficients have been assessed considering the influences of human adipose tissue. Monte Carlo code MCNP4C was used to simulate broad parallel beam monoenergetic neutrons ranging in energy from thermal to 10 MeV. Simulated Irradiations were conducted for standard irradiation geometries. The targets were on gender specific mathematical anthropomorphic phantoms modified to approximate human adipose tissue distributions. Dosimetric analysis compared adipose tissue influence against reference anthropomorphic phantom characteristics. Adipose Male and Post-Menopausal Female Phantoms were derived introducing interstitial adipose tissue to account for 22 and 27 kg additional body mass, respectively, each demonstrating a Body Mass Index (BMI) of 30. An Adipose Female Phantom was derived introducing specific subcutaneous adipose tissue accounting for 15 kg of additional body mass demonstrating a BMI of 26. Neutron dose was shielded in the superficial tissues; giving rise to secondary photons which dominated the effective dose for Incident energies less than 100 keV. Adipose tissue impact on the effective dose was a 25% reduction at the anterior-posterior incidence ranging to a 10% increase at the lateral incidences. Organ dose impacts were more distinctive; symmetrically situated organs demonstrated a 15% reduction at the anterior-posterior Incidence ranging to a 2% increase at the lateral incidences. Abdominal or asymmetrically situated organs demonstrated a 50% reduction at the anterior-posterior incidence ranging to a 25% increase at the lateral incidences.

Effects of temperature on the development and survival of eggs of four coastal California fishes

USGS Publications Warehouse

Gadomski, D.M.; Caddell, S.M.

1996-01-01

Laboratory experiments were conducted to determine the effects of temperature on egg development and survival of four fish species found off southern California. Our objectives were to further understanding ofnatural spawning patterns and to aid in identifying and ageing field-collected specimens. An egg-staging procedure was devised and eggs were observed every two hours during development at a range of temperatures (8-28°Cl. Barred sand bass, Parolabrax nebulifer, eggs survived to hatching and produced viable embryos at the highest temperature range (l6-28°C), reflecting this species'summerspawning season. Fantail sole, Xystreurys liolepis, eggs also hatched at a higher temperature range (l6-24°C). This species spawns primarily from summer through fall. Eggs of the two species with winter-spring spawning peaks, white croaker, Genyonemuslineatus, and California halibut, Paralichthys californicus, had lower temperature-tolerance ranges (12- 2O"C). Developmental rate at a specific temperature did not significantly differ between species, whereas within tolerance limits, temperature strongly affected rate of development for all species. Time to hatching for all species was inversely related to temperature, and the relationship was approximately exponential. Species-specific differences in egg-stage sequence were observed; embryonic organogenesisin relation to germ-ring migration and blastopore closure was faster for barred sand bass and fantail sole than for white croaker and California halibut.

Systematic review of the economic value of diarrheal vaccines

PubMed Central

Rheingans, Richard; Amaya, Mirna; Anderson, John D; Chakraborty, Poulomy; Atem, Jacob

2014-01-01

Diarrheal disease is a leading cause of child mortality in low-income settings and morbidity across a range of settings. A growing number of studies have addressed the economic value of new and emerging vaccines to reduce this threat. We conducted a systematic review to assess the economic value of diarrheal vaccines targeting a range of pathogens in different settings. The majority of studies focused on the economic value of rotavirus vaccines in different settings, with most of these concluding that vaccination would provide significant economic benefits across a range of vaccine prices. There is also evidence of the economic benefits of cholera vaccines in specific contexts. For other potential diarrheal vaccines data are limited and often hypothetical. Across all target pathogens and contexts, the evidence of economic value focuses the short-term health and economic gains. Additional information is needed on the broader social and long-term economic value of diarrhea vaccines. PMID:24861846

High dimensional reflectance analysis of soil organic matter

NASA Technical Reports Server (NTRS)

Henderson, T. L.; Baumgardner, M. F.; Franzmeier, D. P.; Stott, D. E.; Coster, D. C.

1992-01-01

Recent breakthroughs in remote-sensing technology have led to the development of high spectral resolution imaging sensors for observation of earth surface features. This research was conducted to evaluate the effects of organic matter content and composition on narrowband soil reflectance across the visible and reflective infrared spectral ranges. Organic matter from four Indiana agricultural soils, ranging in organic C content from 0.99 to 1.72 percent, was extracted, fractionated, and purified. Six components of each soil were isolated and prepared for spectral analysis. Reflectance was measured in 210 narrow bands in the 400- to 2500-nm wavelength range. Statistical analysis of reflectance values indicated the potential of high dimensional reflectance data in specific visible, near-infrared, and middle-infrared bands to provide information about soil organic C content, but not organic matter composition. These bands also responded significantly to Fe- and Mn-oxide content.

Gas and water flow in an excavation-induced fracture network around an underground drift: A case study for a radioactive waste repository in clay rock

NASA Astrophysics Data System (ADS)

de La Vaissière, Rémi; Armand, Gilles; Talandier, Jean

2015-02-01

The Excavation Damaged Zone (EDZ) surrounding a drift, and in particular its evolution, is being studied for the performance assessment of a radioactive waste underground repository. A specific experiment (called CDZ) was designed and implemented in the Meuse/Haute-Marne Underground Research Laboratory (URL) in France to investigate the EDZ. This experiment is dedicated to study the evolution of the EDZ hydrogeological properties (conductivity and specific storage) of the Callovo-Oxfordian claystone under mechanical compression and artificial hydration. Firstly, a loading cycle applied on a drift wall was performed to simulate the compression effect from bentonite swelling in a repository drift (bentonite is a clay material to be used to seal drifts and shafts for repository closure purpose). Gas tests (permeability tests with nitrogen and tracer tests with helium) were conducted during the first phase of the experiment. The results showed that the fracture network within the EDZ was initially interconnected and opened for gas flow (particularly along the drift) and then progressively closed with the increasing mechanical stress applied on the drift wall. Moreover, the evolution of the EDZ after unloading indicated a self-sealing process. Secondly, the remaining fracture network was resaturated to demonstrate the ability to self-seal of the COx claystone without mechanical loading by conducting from 11 to 15 repetitive hydraulic tests with monitoring of the hydraulic parameters. During this hydration process, the EDZ effective transmissivity dropped due to the swelling of the clay materials near the fracture network. The hydraulic conductivity evolution was relatively fast during the first few days. Low conductivities ranging at 10-10 m/s were observed after four months. Conversely, the specific storage showed an erratic evolution during the first phase of hydration (up to 60 days). Some uncertainty remains on this parameter due to volumetric strain during the sealing of the fractures. The hydration was stopped after one year and cross-hole hydraulic tests were performed to determine more accurately the specific storage as well as the hydraulic conductivity at a meter-scale. All hydraulic conductivity values measured at the injection interval and at the observation intervals were all below 10-10 m/s. Moreover, the preferential inter-connectivity along the drift disappeared. Specific storage values at the observation and injection intervals were similar. Furthermore they were in agreement with the value obtained at the injection interval within the second hydration phase (60 days after starting hydration). The graphical abstract synthesizes the evolution of the hydraulic/gas conductivity for 8 intervals since the beginning of the CDZ experiment. The conductivity limit of 10-10 m/s corresponds to the lower bound hydraulic definition of the EDZ and it is demonstrated that EDZ can be sealed. This is a significant result in the demonstration of the long-term safety of a repository.

Geohydrology, water quality, and conceptual model of the hydrologic system Saco Landfill area, Saco, Maine

USGS Publications Warehouse

Nielsen, M.G.; Stone, J.R.; Hansen, B.P.; Nielsen, J.P.

1995-01-01

A geohydrologic study of the Saco Municipal Landfill in Saco, Maine, was done during 1993-94 to provide a preliminary interpretation of the geology and hydrology needed to guide additional studies at the landfill as part of the Superfund Program. The Saco Landfill, which was active from the early 1960's until 1986, includes three disposal areas on a-90-acre parcel. Sandy Brook, a small perennial stream, flows from north to south through the land- fill between the disposal areas. Discharge of leachate from the disposal areas to aquifers and streams has been documented since 1974. The landfill was declared a Superfund site in 1990 by the U.S. Environmental Protection Agency. Multiple lines of evidence are used in this study to indicate areas of ground-water contamination and sources of water flow in Sandy Brook. The geohydrologic system on the east side of Sandy Brook consists of an upper water-table aquifer and a lower aquifer, separated by a thick sequence of glaciomarine silt and clay. Depths to bedrock range from 60 to more than 200 ft (feet), on the basis of data from seismic-refraction studies and drilling. The upper aquifer, which is generally less than 15 ft thick, consists of fine- to medium-grained sand deposited in a shallow postglacial marine environment. The lower aquifer, which was deposited as a series of glaciomarine fans, contains two sediment types: well-sorted sand *and gravel and unsorted sediments called diamict sediments. East of Sandy Brook, the thickness of the lower aquifer ranges from 25 to 100 ft, based on drilling at the landfill. The glaciomarine silts and clays (known as the presumpscot Formation) range from 50 to more than 100 ft thick. West of Sandy Brook, the glaciomarine silt and clay is largely absent, and fractured bedrock is very close to land surface under one of the disposal areas in the northwestern part of the property. The lower aquifer is unconfined in the southwestern side of the study area; bedrock slopes towards the south, and the aquifer thickens to 100 ft at the southwestern end of the study area. Preliminary estimates of mean annual streamflow in Sandy Brook, based on a partial year of continuous record, indicate that runoff increases from approximately 2.1 ft3/s (cubic feet per second) upstream from the landfill to 2.7 ft3/s downstream from the landfill, although the drainage area down- stream is only 11 percent greater than the drainage area upstream. A water-budget estimate based on available streamflow and climatic data indicates that Sandy Brook below the landfill gains about 80 million gallons per year from sources outside the drainage-basin boundary. Possible sources include the lower aquifer north or west of the landfill area and the fractured bedrock northwest of Sandy Brook. Specific conductance of water in Sandy Brook increases downstream from the landfill. In September 1993, specific conductance was 184 liS/cm (microsiemens per centimeter at 25 degrees Celsius) upstream from the landfill and 496 uS/cm downstream from the landfill. Continuous monitoring of specific conductance in Sandy Brook shows that the downstream increase is less during periods of stormflow because of dilution. Electromagnetic terrain-conductivity surveys, results of ground-water chemical analyses, and changes in streamwater quality have been used to identify areas of likely ground-water contamination. The specific conductance of ground water exceeds 2,000 uS/cm in some areas near the landfills. This compares to specific conductances of less than 200 uS/cm in water from most shallow wells that are considered to represent background water quality. Ground water in the upper aquifer east of Sandy Brook and in the lower aquifer west of Sandy Brook has been affected by leachate flowing from the landfill areas. The extent of contamination in bedrock, if any, is unknown. Water levels measured in 16 wells were used to help determine the direction of ground-water flow. The electromagnetic terrain-conduct

Microwave absorption in powders of small conducting particles for heating applications.

PubMed

Porch, Adrian; Slocombe, Daniel; Edwards, Peter P

2013-02-28

In microwave chemistry there is a common misconception that small, highly conducting particles heat profusely when placed in a large microwave electric field. However, this is not the case; with the simple physical explanation that the electric field (which drives the heating) within a highly conducting particle is highly screened. Instead, it is the magnetic absorption associated with induction that accounts for the large experimental heating rates observed for small metal particles. We present simple principles for the effective heating of particles in microwave fields from calculations of electric and magnetic dipole absorptions for a range of practical values of particle size and conductivity. For highly conducting particles, magnetic absorption dominates electric absorption over a wide range of particle radii, with an optimum absorption set by the ratio of mean particle radius a to the skin depth δ (specifically, by the condition a = 2.41δ). This means that for particles of any conductivity, optimized magnetic absorption (and hence microwave heating by magnetic induction) can be achieved by simple selection of the mean particle size. For weakly conducting samples, electric dipole absorption dominates, and is maximized when the conductivity is approximately σ ≈ 3ωε(0) ≈ 0.4 S m(-1), independent of particle radius. Therefore, although electric dipole heating can be as effective as magnetic dipole heating for a powder sample of the same volume, it is harder to obtain optimized conditions at a fixed frequency of microwave field. The absorption of sub-micron particles is ineffective in both magnetic and electric fields. However, if the particles are magnetic, with a lossy part to their complex permeability, then magnetic dipole losses are dramatically enhanced compared to their values for non-magnetic particles. An interesting application of this is the use of very small magnetic particles for the selective microwave heating of biological samples.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kuchinskii, E. Z., E-mail: kuchinsk@iep.uran.ru; Kuleeva, N. A.; Sadovskii, M. V., E-mail: sadovski@iep.uran.ru

We derive a Ginzburg–Landau (GL) expansion in the disordered attractive Hubbard model within the combined Nozieres–Schmitt-Rink and DMFT+Σ approximation. Restricting ourselves to the homogeneous expansion, we analyze the disorder dependence of GL expansion coefficients for a wide range of attractive potentials U, from the weak BCS coupling region to the strong-coupling limit, where superconductivity is described by Bose–Einstein condensation (BEC) of preformed Cooper pairs. We show that for the a semielliptic “bare” density of states of the conduction band, the disorder influence on the GL coefficients A and B before quadratic and quartic terms of the order parameter, as wellmore » as on the specific heat discontinuity at the superconducting transition, is of a universal nature at any strength of the attractive interaction and is related only to the general widening of the conduction band by disorder. In general, disorder growth increases the values of the coefficients A and B, leading either to a suppression of the specific heat discontinuity (in the weak-coupling limit), or to its significant growth (in the strong-coupling region). However, this behavior actually confirms the validity of the generalized Anderson theorem, because the disorder dependence of the superconducting transition temperature T{sub c}, is also controlled only by disorder widening of the conduction band (density of states).« less

An ultrasensitive electrochemical immunosensor for the detection of prostate-specific antigen based on conductivity nanocomposite with halloysite nanotubes.

PubMed

Li, Yueyuan; Khan, Malik Saddam; Tian, Lihui; Liu, Li; Hu, Lihua; Fan, Dawei; Cao, Wei; Wei, Qin

2017-05-01

A sensitive label-free amperometric electrochemical immunosensor for detection of prostate-specific antigen (PSA) was proposed in this work. The nanocomposite of halloysite nanotubes with polypyrrole shell and palladium nanoparticles (HNTs@PPy-Pd) was used as a novel signal label. The HNTs with adequate hydroxyl groups are economically available raw materials. PPy, as an electrically conducting polymer material, can be absorbed to the surface of HNTs by in situ oxidative polymerization of the pyrrole monomer and form a shell on the HNTs. The shell of PPy could not only improve the conductivity of the nanocomposite but also absorb large amounts of Pd nanoparticles (NPs). The Pd NPs with high electrocatalytic activity toward the reduction of H 2 O 2 and the HNTs@PPy-Pd nanocomposite as the analytical signal label could improve the sensitivity of the immunosensor. Under optimal conditions, the immunosensor showed a low detection limit (0.03 pg/mL) and a wide linear range (0.0001 to 25 ng/mL) of PSA. Moreover, its merits such as good selectivity, acceptable reproducibility, and stability indicate that the fabricated immunosensor has a promising application potential in clinical diagnosis. Graphical Abstract A new label-free amperometric electrochemical immunosensor based on HNTs@PPy-Pd nanocomposite for quantitative detection of PSA.

Sensitivity and Specificity of 2 Autism Screeners Among Referred Children Between 16 and 48 Months of Age.

PubMed

Salisbury, Louisa A; Nyce, Jonathan D; Hannum, Charles D; Sheldrick, R Christopher; Perrin, Ellen C

2018-04-01

Autism screening is recommended by the American Academy of Pediatrics and the Centers for Disease Control and Prevention at ages 18 and 24 months. Popular screening tests have been validated for the age range of 16 to 30 months. However, only a minority of children with autism spectrum disorder (ASD) are identified by age 3 years, and many are not identified until after they enter school. Thus, we aimed to measure the sensitivity and specificity of 2 available screening tests for ASDs in children older than 30 months. We assessed the sensitivity and specificity of 2 ASD screening tools administered to parents of children who were referred to a developmental clinic between the ages of 16 and 48 months: the Modified Checklist for Autism in Toddlers (M-CHAT) and the Parent's Observations of Social Interactions (POSI), which is a component of a comprehensive screening instrument called, the Survey of Well-being of Young Children. Both the M-CHAT and the POSI had acceptable sensitivity (≥75%) among children across the age range studied. Their specificity was limited by the fact that the study was conducted in a developmental referral clinic. Two readily available screening tools, the POSI and the M-CHAT, have acceptable sensitivity in evaluating risk for autism in children at least to age 48 months. Further research should investigate their sensitivity and specificity when used in primary care settings.

Control of air emissions from POTWs using biofiltration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Webster, T.S.; Devinny, J.S.; Torres, E.M.

1995-12-31

The University of Southern California (USC), in collaboration with the County Sanitation Districts of Orange County (CSDOC), the South Coast Air Quality Management District (SCAQMD), Southern California Edison (SCE), the Water Environment Research Foundation (WERF), and Huntingdon Environmental Engineering, Inc. (HEEI), is conducting a research project to evaluate the application of biofiltration to remove volatile organic compounds (VOCs), odor-causing air pollutants, and toxics from a publicly owned treatment works (POTW) waste airstream. As part of this project, bench-scale and pilot-scale experiments are being conducted to test the effectiveness of biofiltration and determine the optimum parameters for applying biofiltration to POTWs.more » Results from the bench-scale experiments demonstrate that biofiltration is effective in reducing the concentration of hydrogen sulfide (H{sub 2}S) and total VOCs present in waste airstreams by over 99% and up to 90%, respectively. Average reduction of specific aromatic and carbonyl compounds ranged from 55% to 91%. Removal efficiencies for chlorinated hydrocarbons were variable, ranging from 6% to 88%. Overall, biofiltration appears to be a promising technology for full-scale implementation at POTWs for VOC and odor emission compliance.« less

Real-Time Quantum Dynamics of Long-Range Electronic Excitation Transfer in Plasmonic Nanoantennas.

PubMed

Ilawe, Niranjan V; Oviedo, M Belén; Wong, Bryan M

2017-08-08

Using large-scale, real-time, quantum dynamics calculations, we present a detailed analysis of electronic excitation transfer (EET) mechanisms in a multiparticle plasmonic nanoantenna system. Specifically, we utilize real-time, time-dependent, density functional tight binding (RT-TDDFTB) to provide a quantum-mechanical description (at an electronic/atomistic level of detail) for characterizing and analyzing these systems, without recourse to classical approximations. We also demonstrate highly long-range electronic couplings in these complex systems and find that the range of these couplings is more than twice the conventional cutoff limit considered by Förster resonance energy transfer (FRET)-based approaches. Furthermore, we attribute these unusually long-ranged electronic couplings to the coherent oscillations of conduction electrons in plasmonic nanoparticles. This long-range nature of plasmonic interactions has important ramifications for EET; in particular, we show that the commonly used "nearest-neighbor" FRET model is inadequate for accurately characterizing EET even in simple plasmonic antenna systems. These findings provide a real-time, quantum-mechanical perspective for understanding EET mechanisms and provide guidance in enhancing plasmonic properties in artificial light-harvesting systems.

Preference limits of the visual dynamic range for ultra high quality and aesthetic conveyance

NASA Astrophysics Data System (ADS)

Daly, Scott; Kunkel, Timo; Sun, Xing; Farrell, Suzanne; Crum, Poppy

2013-03-01

A subjective study was conducted to investigate the preferred maximum and minimum display luminances in order to determine the dynamic ranges for future displays. Two studies address the diffuse reflective regions, and a third study tested preferences of highlight regions. Preferences, as opposed to detection thresholds, were studied to provide results more directly relevant to the viewing of entertainment or art. Test images were specifically designed to test these limits without the perceptual conflicts that usually occur in these types of studies. For the diffuse range, we found a display with a dynamic range having luminances between 0.1 and 650 cd/m2 matches the average preferences. However, to satisfy 90% of the population, a dynamic range from 0.005 and ~3,000 cd/m2 is needed. Since a display should be able to produce values brighter than the diffuse white maximum, as in specular highlights and emissive sources, the highlight study concludes that even the average preferred maximum luminance for highlight reproduction is ~4,000 cd/m2.

Conductivity in zeolite-polymer composite membranes for PEMFCs

NASA Astrophysics Data System (ADS)

Sancho, T.; Soler, J.; Pina, M. P.

Structured materials, such as zeolites can be candidates to be used as electrolytes in proton exchange membrane fuel cells (PEMFC) to substitute polymeric membranes, taking advantage of their higher chemical and thermal stability and their specific adsorption properties. The possibility to work at temperatures of nearly 150 °C would make easy the selection of the fuel, decreasing the influence of CO in the catalyst poisoning, and it would also improve the kinetics of the electrochemical reactions involved. In this work, four zeolites and related materials have been studied: mordenite, NaA zeolite, umbite and ETS-10. In special, the influence of relative humidity and temperature have been carefully explored. A conductivity cell was designed and built to measure in cross direction, by using the electrochemical impedance spectroscopy. The experimental system was validated using Nafion ® as a reference material by comparing the results with bibliography data. Samples were prepared by pressing the zeolite powders, with size of 1 μm on average, using polymer PVDF (10 wt.%) as a binder. The results here obtained, in spite of not reaching the absolute values of the Nafion ® ones, show a lower effect of the dehydration phenomenon on the conduction performance in the temperature range studied (from room temperature to 150 °C). This increase of the operation temperature range would give important advantages to the PEMFC. ETS-10 sample shows the best behaviour with respect to conductivity exhibiting an activation energy value comparable with reported for Nafion ® membrane.

Water-quality assessment of the Cypress Creek watershed, Warrick County, Indiana

USGS Publications Warehouse

Bobo, Linda L.; Peters, Charles A.

1980-01-01

The U.S. Soil Conservation Service needs chemical, biological, microbiological, and hydrological data to prepare an environmental evaluation of the water quality in the Cypress Creek watershed, Warrick County, Ind., before plans can be devised to (1) improve water quality, (2) minimize flooding, (3) reduce sedimentation, and (4) provide adequate outlets for drainage in the watershed. The U.S. Geological Survey obtained these data for the Soil Conservation Service in a water-quality survey of the watershed from March to August 1979. Past and present surface coal mining is the factor having the greatest impact on water quality in the watershed. The upper reaches of Cypress Creek receive acid-mine drainage from a coal-mine waste slurry during periods of intense rainfall. All the remaining tributaries, except Summer Pecka ditch, drain mined or reclaimed lands. The general water type of Cypress Creek and most of its tributaries is calcium and magnesium sulfate. In contrast, the water type at background site 21 on Summer Pecka ditch is calcium sulfate. Specific conductance ranged from 470 to 4,730 micromhos per centimeter at 25 degrees Celsius, and pH ranged from 1.2 to 8.8. Specific conductance, hardness, and concentrations of major ions and dissolved solids were highest in tributaries affected by mining. The pH was lowest in the same tributaries. Concentrations of iron, manganese, and sulfate in water samples and chlordane, DDT, and PCB 's in streambed samples exceeded water-quality limits set by the U.S. Environmental Protection Agency. (USGS)

Predictions of dispersion and deposition of fallout from nuclear testing using the NOAA-HYSPLIT meteorological model.

PubMed

Moroz, Brian E; Beck, Harold L; Bouville, André; Simon, Steven L

2010-08-01

The NOAA Hybrid Single-Particle Lagrangian Integrated Trajectory Model (HYSPLIT) was evaluated as a research tool to simulate the dispersion and deposition of radioactive fallout from nuclear tests. Model-based estimates of fallout can be valuable for use in the reconstruction of past exposures from nuclear testing, particularly where little historical fallout monitoring data are available. The ability to make reliable predictions about fallout deposition could also have significant importance for nuclear events in the future. We evaluated the accuracy of the HYSPLIT-predicted geographic patterns of deposition by comparing those predictions against known deposition patterns following specific nuclear tests with an emphasis on nuclear weapons tests conducted in the Marshall Islands. We evaluated the ability of the computer code to quantitatively predict the proportion of fallout particles of specific sizes deposited at specific locations as well as their time of transport. In our simulations of fallout from past nuclear tests, historical meteorological data were used from a reanalysis conducted jointly by the National Centers for Environmental Prediction (NCEP) and the National Center for Atmospheric Research (NCAR). We used a systematic approach in testing the HYSPLIT model by simulating the release of a range of particle sizes from a range of altitudes and evaluating the number and location of particles deposited. Our findings suggest that the quantity and quality of meteorological data are the most important factors for accurate fallout predictions and that, when satisfactory meteorological input data are used, HYSPLIT can produce relatively accurate deposition patterns and fallout arrival times. Furthermore, when no other measurement data are available, HYSPLIT can be used to indicate whether or not fallout might have occurred at a given location and provide, at minimum, crude quantitative estimates of the magnitude of the deposited activity. A variety of simulations of the deposition of fallout from atmospheric nuclear tests conducted in the Marshall Islands (mid-Pacific), at the Nevada Test Site (U.S.), and at the Semipalatinsk Nuclear Test Site (Kazakhstan) were performed. The results of the Marshall Islands simulations were used in a limited fashion to support the dose reconstruction described in companion papers within this volume.

PREDICTIONS OF DISPERSION AND DEPOSITION OF FALLOUT FROM NUCLEAR TESTING USING THE NOAA-HYSPLIT METEOROLOGICAL MODEL

PubMed Central

Moroz, Brian E.; Beck, Harold L.; Bouville, André; Simon, Steven L.

2013-01-01

The NOAA Hybrid Single-Particle Lagrangian Integrated Trajectory Model (HYSPLIT) was evaluated as a research tool to simulate the dispersion and deposition of radioactive fallout from nuclear tests. Model-based estimates of fallout can be valuable for use in the reconstruction of past exposures from nuclear testing, particularly, where little historical fallout monitoring data is available. The ability to make reliable predictions about fallout deposition could also have significant importance for nuclear events in the future. We evaluated the accuracy of the HYSPLIT-predicted geographic patterns of deposition by comparing those predictions against known deposition patterns following specific nuclear tests with an emphasis on nuclear weapons tests conducted in the Marshall Islands. We evaluated the ability of the computer code to quantitatively predict the proportion of fallout particles of specific sizes deposited at specific locations as well as their time of transport. In our simulations of fallout from past nuclear tests, historical meteorological data were used from a reanalysis conducted jointly by the National Centers for Environmental Prediction (NCEP) and the National Center for Atmospheric Research (NCAR). We used a systematic approach in testing the HYSPLIT model by simulating the release of a range of particles sizes from a range of altitudes and evaluating the number and location of particles deposited. Our findings suggest that the quantity and quality of meteorological data are the most important factors for accurate fallout predictions and that when satisfactory meteorological input data are used, HYSPLIT can produce relatively accurate deposition patterns and fallout arrival times. Furthermore, when no other measurement data are available, HYSPLIT can be used to indicate whether or not fallout might have occurred at a given location and provide, at minimum, crude quantitative estimates of the magnitude of the deposited activity. A variety of simulations of the deposition of fallout from atmospheric nuclear tests conducted in the Marshall Islands, at the Nevada Test Site (USA), and at the Semipalatinsk Nuclear Test Site (Kazakhstan) were performed using reanalysis data composed of historic meteorological observations. The results of the Marshall Islands simulations were used in a limited fashion to support the dose reconstruction described in companion papers within this volume. PMID:20622555

Continuous tidal streamflow, water level, and specific conductance data for Union Creek and the Little Back, Middle, and Front Rivers, Savannah River Estuary, November 2008 to March 2009

USGS Publications Warehouse

Lanier, Timothy H.; Conrads, Paul

2010-01-01

In the Water Resource Development Act of 1999, the U.S. Congress authorized the deepening of the Savannah Harbor. Additional studies were then identified by the Georgia Ports Authority and other local and regional stakeholders to determine and fully describe the potential environmental effects of deepening the channel. One need that was identified was the validation of a three-dimensional hydrodynamic model developed to evaluate mitigation scenarios for a potential harbor deepening and the effects on the Savannah River estuary. The streamflow in the estuary is very complex due to reversing tidal flows, interconnections of streams and tidal creeks, and the daily flooding and draining of the marshes. The model was calibrated using very limited streamflow data and no continuous streamflow measurements. To better characterize the streamflow dynamics and mass transport of the estuary, two index-velocity sites were instrumented with continuous acoustic velocity, water level, and specific conductance sensors on the Little Back and Middle Rivers for the 5-month period of November 2008 through March 2009. During the same period, a third acoustic velocity meter was installed on the Front River just downstream from U.S. Geological Survey streamgaging station 02198920 (Savannah River at GA 25, at Port Wentworth, Georgia) where water level and specific conductance data were being collected. A fourth index-velocity site was instrumented with continuous acoustic velocity, water level, and specific conductance sensors on Union Creek for a 2-month period starting in November 2008. In addition to monitoring the tidal cycles, streamflow measurements were made at the four index-velocity sites to develop ratings to compute continuous discharge for each site. The maximum flood (incoming) and ebb (outgoing) tides measured on Little Back River were –4,570 and 7,990 cubic feet per second, respectively. On Middle River, the maximum flood and ebb tides measured were –9,630 and 13,600 cubic feet per second, respectively. On Front River, the maximum flood and ebb tides were –34,500 and 43,700 cubic feet per second, respectively; and on Union Creek, the maximum flood and ebb tides were –2,390 and 4,610 cubic feet per second, respectively. During the 5-month instrumentation deployment, computed tidal streamflows on Little Back River ranged from –7,820 to 9,600 cubic feet per second for the flood and ebb tides, respectively. On Middle River, the computed tidal streamflows ranged from –17,500 to 22,500 cubic feet per second for the flood and ebb tides, respectively. The computed tidal streamflows on Front River ranged from –78,900 to 87,200 cubic feet per second, and from –3,850 to 6,130 cubic feet per second on Union Creek for the flood and ebb tides, respectively. The streamgages on the Little Back, Middle, and Front Rivers have continued in operation following the initial 5-month deployment.

Predicting lattice thermal conductivity with help from ab initio methods

NASA Astrophysics Data System (ADS)

Broido, David

2015-03-01

The lattice thermal conductivity is a fundamental transport parameter that determines the utility a material for specific thermal management applications. Materials with low thermal conductivity find applicability in thermoelectric cooling and energy harvesting. High thermal conductivity materials are urgently needed to help address the ever-growing heat dissipation problem in microelectronic devices. Predictive computational approaches can provide critical guidance in the search and development of new materials for such applications. Ab initio methods for calculating lattice thermal conductivity have demonstrated predictive capability, but while they are becoming increasingly efficient, they are still computationally expensive particularly for complex crystals with large unit cells . In this talk, I will review our work on first principles phonon transport for which the intrinsic lattice thermal conductivity is limited only by phonon-phonon scattering arising from anharmonicity. I will examine use of the phase space for anharmonic phonon scattering and the Grüneisen parameters as measures of the thermal conductivities for a range of materials and compare these to the widely used guidelines stemming from the theory of Liebfried and Schölmann. This research was supported primarily by the NSF under Grant CBET-1402949, and by the S3TEC, an Energy Frontier Research Center funded by the US DOE, office of Basic Energy Sciences under Award No. DE-SC0001299.

Functional and topological characteristics of mammalian regulatory domains

PubMed Central

Symmons, Orsolya; Uslu, Veli Vural; Tsujimura, Taro; Ruf, Sandra; Nassari, Sonya; Schwarzer, Wibke; Ettwiller, Laurence; Spitz, François

2014-01-01

Long-range regulatory interactions play an important role in shaping gene-expression programs. However, the genomic features that organize these activities are still poorly characterized. We conducted a large operational analysis to chart the distribution of gene regulatory activities along the mouse genome, using hundreds of insertions of a regulatory sensor. We found that enhancers distribute their activities along broad regions and not in a gene-centric manner, defining large regulatory domains. Remarkably, these domains correlate strongly with the recently described TADs, which partition the genome into distinct self-interacting blocks. Different features, including specific repeats and CTCF-binding sites, correlate with the transition zones separating regulatory domains, and may help to further organize promiscuously distributed regulatory influences within large domains. These findings support a model of genomic organization where TADs confine regulatory activities to specific but large regulatory domains, contributing to the establishment of specific gene expression profiles. PMID:24398455

Improvement of Ohmic contacts on Ga 2O 3 through use of ITO-interlayers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carey, Patrick H.; Yang, Jiancheng; Ren, Fan

In this work, the use of ITO interlayers between Ga 2O 3 and Ti/Au metallization is shown to produce Ohmic contacts after annealing in the range of 500–600 °C. Without the ITO, similar anneals do not lead to linear current–voltage characteristics. Transmission line measurements were used to extract the specific contact resistance of the Au/Ti/ITO/Ga 2O 3 stacks as a function of annealing temperature. Sheet, specific contact, and transfer resistances all decreased sharply from as-deposited values with annealing. The minimum transfer resistance and specific contact resistance of 0.60 Ω mm and 6.3 × 10 -5 Ω cm 2 were achievedmore » after 600 °C annealing, respectively. Lastly, the conduction band offset between ITO and Ga 2O 3 is 0.32 eV and is consistent with the improved electron transport across the heterointerface.« less

Hydrologic data for Leviathan Mine and vicinity, Alpine County, California, 1981-83

USGS Publications Warehouse

Hammermeister, D.P.; Walmsley, S.J.

1985-01-01

The U.S. Geological Survey collected basic hydrologic and water-quality data during 1981-83 to facilitate the geohydrologic evaluation of the Leviathan Mine area and the design of a pollution-abatement project. Surface-water field data included one or more measurements of pH, water temperature, and specific conductance at 45 sites in and adjacent to the mine area. At nine of these sites, daily data on discharge, specific conductance, and water temperature were collected during parts of 1981-82 by using electronic monitor-recorder systems. Ground-water field data included one or more of the water-quality measurements listed above at 71 piezometers in the mine area. Borehole geophysical data included neutron-moisture, neutron-porosity, gamma-gamma density, natural gamma, and temperature logs at three sites. Mineralogic and hydrologic data were obtained for cores taken from nine test holes. One or more surface-water samples from 26 sites were analyzed for major cations, major anions, and a wide range of minor inorganic constituents. Single ground-water samples from 36 piezometers were analyzed for the same array of major and minor constituents. (USGS)

Boundaries of the critical state stability in a hard superconductor Nb3Al in the H-T plane

NASA Astrophysics Data System (ADS)

Chabanenko, V. V.; Vasiliev, S. V.; Nabiałek, A.; Shishmakov, A. S.; Pérez-Rodríguez, F.; Rusakov, V. F.; Szewczyk, A.; Kodess, B. N.; Gutowska, M.; Wieckowski, J.; Szymczak, H.

2013-04-01

The instability of the critical state in a type-II superconductor Nb3Al is studied for the first time for simultaneous consideration of real dependences of thermal and conductive properties of the material on temperature T and magnetic field He. To do this the dependences of specific heat C(T,Hе), magnetization M(T,He) and magnetostriction ΔL(T,He) of the superconductor were investigated experimentally in a strong magnetic field (up to 12 T). The gap width, the coefficient of the linear term, which determines the electronic contribution to the specific heat, the Debye temperature, and other parameters were found using experimental data on the heat capacity in a wide range of temperatures and magnetic fields Hc1 ≤ He ≤ Hc2. From experimental studies of magnetization the dependences of the critical current of the superconductor, Jc(T,He), were reconstructed. The hysteresis loops of magnetization and magnetostriction were calculated using experimental data for temperature and field dependences of the thermal and conductive properties.

Genetic characterization, molecular epidemiology, and phylogenetic relationships of insect-specific viruses in the taxon Negevirus

PubMed Central

Nunes, Marcio R.T.; Contreras-Gutierrez, María Angélica; Guzman, Hilda; Martins, Livia C.; Barbirato, Mayla Feitoza; Savit, Chelsea; Balta, Victoria; Uribe, Sandra; Vivero, Rafael; Suaza, Juan David; Oliveira, Hamilton; Nunes Neto, Joaquin P.; Carvalho, Valeria L.; da Silva, Sandro Patroca; Cardoso, Jedson F.; de Oliveira, Rodrigo Santo; da Silva Lemos, Poliana; Wood, Thomas G.; Widen, Steven G.; Vasconcelos, Pedro F.C.; Fish, Durland; Vasilakis, Nikos; Tesh, Robert B.

2017-01-01

The recently described taxon Negevirus is comprised of a diverse group of insect-specific viruses isolated from mosquitoes and phlebotomine sandflies. In this study, a comprehensive genetic characterization, molecular, epidemiological and evolutionary analyses were conducted on nearly full-length sequences of 91 new negevirus isolates obtained in Brazil, Colombia, Peru, Panama, USA and Nepal. We demonstrated that these arthropod restricted viruses are clustered in two major phylogenetic groups with origins related to three plant virus genera (Cilevirus, Higrevirus and Blunevirus). Molecular analyses demonstrated that specific host correlations are not present with most negeviruses; instead, high genetic variability, wide host-range, and cross-species transmission were noted. The data presented here also revealed the existence of five novel insect-specific viruses falling into two arthropod-restrictive virus taxa, previously proposed as distinct genera, designated Nelorpivirus and Sandewavirus. Our results provide a better understanding of the molecular epidemiology, evolution, taxonomy and stability of this group of insect-restricted viruses. PMID:28193550

Genetic characterization, molecular epidemiology, and phylogenetic relationships of insect-specific viruses in the taxon Negevirus.

PubMed

Nunes, Marcio R T; Contreras-Gutierrez, María Angélica; Guzman, Hilda; Martins, Livia C; Barbirato, Mayla Feitoza; Savit, Chelsea; Balta, Victoria; Uribe, Sandra; Vivero, Rafael; Suaza, Juan David; Oliveira, Hamilton; Nunes Neto, Joaquin P; Carvalho, Valeria L; da Silva, Sandro Patroca; Cardoso, Jedson F; de Oliveira, Rodrigo Santo; da Silva Lemos, Poliana; Wood, Thomas G; Widen, Steven G; Vasconcelos, Pedro F C; Fish, Durland; Vasilakis, Nikos; Tesh, Robert B

2017-04-01

The recently described taxon Negevirus is comprised of a diverse group of insect-specific viruses isolated from mosquitoes and phlebotomine sandflies. In this study, a comprehensive genetic characterization, molecular, epidemiological and evolutionary analyses were conducted on nearly full-length sequences of 91 new negevirus isolates obtained in Brazil, Colombia, Peru, Panama, USA and Nepal. We demonstrated that these arthropod restricted viruses are clustered in two major phylogenetic groups with origins related to three plant virus genera (Cilevirus, Higrevirus and Blunevirus). Molecular analyses demonstrated that specific host correlations are not present with most negeviruses; instead, high genetic variability, wide host-range, and cross-species transmission were noted. The data presented here also revealed the existence of five novel insect-specific viruses falling into two arthropod-restrictive virus taxa, previously proposed as distinct genera, designated Nelorpivirus and Sandewavirus. Our results provide a better understanding of the molecular epidemiology, evolution, taxonomy and stability of this group of insect-restricted viruses. Copyright © 2017 Elsevier Inc. All rights reserved.

Specific heat and related thermophysical properties of liquid Fe-Cu-Mo alloy

NASA Astrophysics Data System (ADS)

Wang, Haipeng; Luo, Bingchi; Chang, Jian; Wei, Bingbo

2007-08-01

The specific heat and related thermophysical properties of liquid Fe77.5Cu13Mo9.5 monotectic alloy were investigated by an electromagnetic levitation drop calorimeter over a wide temperature range from 1482 to 1818 K. A maximum undercooling of 221 K (0.13 T m) was achieved and the specific heat was determined as 44.71 J·mol-1·K-1. The excess specific heat, enthalpy change, entropy change and Gibbs free energy difference of this alloy were calculated on the basis of experimental results. It was found that the calculated results by traditional estimating methods can only describe the solidification process under low undercooling conditions. Only the experimental results can reflect the reality under high undercooling conditions. Meanwhile, the thermal diffusivity, thermal conductivity, and sound speed were derived from the present experimental results. Furthermore, the solidified microstructural morphology was examined, which consists of (Fe) and (Cu) phases. The calculated interface energy was applied to exploring the correlation between competitive nucleation and solidification microstructure within monotectic alloy.

The impact of obesity on specific airway resistance and conductance among schoolchildren.

PubMed

Parraguez Arévalo, Andrea; Rojas Navarro, Francisco; Ruz Céspedes, Macarena; Medina González, Paul; Escobar Cabello, Máximo; Muñoz Cofré, Rodrigo

2018-04-01

Child and adolescent obesity is an epidemiological problem in developing countries. Its prevalence among preschoolers and schoolchildren is over 30%. It has been associated with a wide range of health complications, including rapid loss of lung function leading to changes in physiology and ventilatory mechanics. The objective of this study was to analyze the association between obesity and the increase in specific airway resistance (sRaw) in a sample of obese children and adolescents from the district of Talca. In a sample of 36 subjects with an average age of 9.38 ± 1.99 years, divided into 2 groups (normal weight and obese), the tricipital, subscapular, and abdominal skinfolds and lung volumes were measured. For the statistical analysis, data normality was determined and then the Student's t test or the Mann-Whitney U test and Pearson's or Spearman's correlations were used, as applicable. A value of p < 0.05 was considered statistically significant. When comparing normal weight and obese subjects, a significant increase in sRaw and a significant reduction in specific airway conductance (sGaw) were observed in obese subjects. In addition, an adequate and significant correlation was observed between sRaw and fat percentage. Obese subjects showed an increased sRaw and a reduced sGaw. Sociedad Argentina de Pediatría.

Evaluation of high specific-heat ceramic for regenerator use at temperatures between 2-30 K

NASA Technical Reports Server (NTRS)

Lawless, W. N.

1979-01-01

Specific heat, thermal conductivity (both in the range 2-30 K), and microhardness data were measured on the ceramics labelled LS-8, LS-8A, and LS-8A doped with CsI, SnCl2, and AgCl. A work hardened sample of LS-8A was also studied in an effort to determine the feasibility of using these types of LS-8 materials to replace Pb spheres in the regenerator of the JPL cryocooler. The LS-8A materials are all more than an order of magnitude harder than Pb, and the dopants do not significantly improve the hardness. However, the SnCl2 dopant has a remarkable effect in improving the specific heat and thermal conductivity of LS-8A. The SnCl2 doping level which maximized the regenerator enthalpy change in going from an unloaded to a loaded condition was found to be 0.2 percent SnCl2 in LS-8A. It was also found that the enthalpy change for a regenerator employing the LS-8A material is more than three times larger than for the Pb spheres case. The use of rods, rather than spheres, of optimally doped LS-8A in regenerators is discussed.

Comparison of working efficiency of terrestrial laser scanner in day and night conditions

NASA Astrophysics Data System (ADS)

Arslan, A. E.; Kalkan, K.

2013-10-01

Terrestrial Laser Scanning is a popular and widely used technique to scan existing objects, document historical sites and items, and remodel them if and when needed. Their ability to collect thousands of point data per second makes them an invaluable tool in many areas from engineering to historical reconstruction. There are many scanners in the market with different technical specifications. One main technical specification of laser scanners is range and illumination. In this study, it is tested to be determined the optimal working times of a laser scanner and the scanners consistency with its specifications sheet. In order to conduct this work, series of GNSS measurements in Istanbul Technical University have been carried out, connected to the national reference network, to determine precise positions of target points and the scanner, which makes possible to define a precise distance between the scanner and targets. Those ground surveys has been used for calibration and registration purposes. Two different scan campaigns conducted at 12 am and 11 pm to compare working efficiency of laser scanner in different illumination conditions and targets are measured with a handheld spectro-radiometer in order to determine their reflective characteristics. The obtained results are compared and their accuracies have been analysed.

Short- and long-term effects of clinical audits on compliance with procedures in CT scanning.

PubMed

Oliveri, Antonio; Howarth, Nigel; Gevenois, Pierre Alain; Tack, Denis

2016-08-01

To test the hypothesis that quality clinical audits improve compliance with the procedures in computed tomography (CT) scanning. This retrospective study was conducted in two hospitals, based on 6950 examinations and four procedures, focusing on the acquisition length in lumbar spine CT, the default tube current applied in abdominal un-enhanced CT, the tube potential selection for portal phase abdominal CT and the use of a specific "paediatric brain CT" procedure. The first clinical audit reported compliance with these procedures. After presenting the results to the stakeholders, a second audit was conducted to measure the impact of this information on compliance and was repeated the next year. Comparisons of proportions were performed using the Chi-square Pearson test. Depending on the procedure, the compliance rate ranged from 27 to 88 % during the first audit. After presentation of the audit results to the stakeholders, the compliance rate ranged from 68 to 93 % and was significantly improved for all procedures (P ranging from <0.001 to 0.031) in both hospitals and remained unchanged during the third audit (P ranging from 0.114 to 0.999). Quality improvement through repeated compliance audits with CT procedures durably improves this compliance. • Compliance with CT procedures is operator-dependent and not perfect. • Compliance differs between procedures and hospitals, even within a unified department. • Compliance is improved through audits followed by communication to the stakeholders. • This improvement is sustainable over a one-year period.

Assessment of Techniques for Measuring Tropospheric H Sub x O Sub y

NASA Technical Reports Server (NTRS)

Hoell, J. M. (Editor)

1984-01-01

In its continuing efforts to direct its applications programs towards relevant national needs, NASA is conducting the Tropospheric Chemistry Program, the long-range objective of which is to apply NASA's space technology to assess and predict human impact on the troposphere, particularly on the regional to global scale. One area of required research is instrumentation development, which is aimed at improving the capability to measure important trace gases and aerosols which are key species in the major atmospheric biogeochemical cycles. To focus on specific needs, the Instrumentation Worksphop for H(x)O(y) Tropospheric Species was conducted in August 1982. The workshop discussed current measurement needs and instrument capabilities for H(x)O(y) species, including OH, HO2, and H2O2. The workshop activities and conclusions are documented.

NEXT Ion Engine 2000 Hour Wear Test Results

NASA Technical Reports Server (NTRS)

Soulas, George C.; Kamhawi, Hani; Patterson, Michael J.; Britton, Melissa A.; Frandina, Michael M.

2004-01-01

The results of the NEXT 2000 h wear test are presented. This test was conducted with a 40 cm engineering model ion engine, designated EM1, at a 3.52 A beam current and 1800 V beam power supply voltage. Performance tests, which were conducted over a throttling range of 1.1 to 6.9 kW throughout the wear test, demonstrated that EM1 satisfied all thruster performance requirements. The ion engine accumulated 2038 h of operation at a thruster input power of 6.9 kW, processing 43 kg of xenon. Overall ion engine performance, which includes thrust, thruster input power, specific impulse, and thrust efficiency, was steady with no indications of performance degradation. The ion engine was also inspected following the test. This paper presents these findings.

Visual ecology and potassium conductances of insect photoreceptors.

PubMed

Frolov, Roman; Immonen, Esa-Ville; Weckström, Matti

2016-04-01

Voltage-activated potassium channels (Kv channels) in the microvillar photoreceptors of arthropods are responsible for repolarization and regulation of photoreceptor signaling bandwidth. On the basis of analyzing Kv channels in dipteran flies, it was suggested that diurnal, rapidly flying insects predominantly express sustained K(+) conductances, whereas crepuscular and nocturnally active animals exhibit strongly inactivating Kv conductances. The latter was suggested to function for minimizing cellular energy consumption. In this study we further explore the evolutionary adaptations of the photoreceptor channelome to visual ecology and behavior by comparing K(+) conductances in 15 phylogenetically diverse insects, using patch-clamp recordings from dissociated ommatidia. We show that rapid diurnal flyers such as the blowfly (Calliphora vicina) and the honeybee (Apis mellifera) express relatively large noninactivating Kv conductances, conforming to the earlier hypothesis in Diptera. Nocturnal and/or slow-moving species do not in general exhibit stronger Kv conductance inactivation in the physiological membrane voltage range, but the photoreceptors in species that are known to rely more on vision behaviorally had higher densities of sustained Kv conductances than photoreceptors of less visually guided species. No statistically significant trends related to visual performance could be identified for the rapidly inactivating Kv conductances. Counterintuitively, strong negative correlations were observed between photoreceptor capacitance and specific membrane conductance for both sustained and inactivating fractions of Kv conductance, suggesting insignificant evolutionary pressure to offset negative effects of high capacitance on membrane filtering with increased conductance. Copyright © 2016 the American Physiological Society.

Preliminary characterization of a water vaporizer for resistojet applications

NASA Technical Reports Server (NTRS)

Morren, W. Earl

1992-01-01

A series of tests was conducted to explore the characteristics of a water vaporizer intended for application to resistojet propulsion systems. The objectives of these tests were to (1) observe the effect of orientation with respect to gravity on vaporizer stability, (2) characterize vaporizer efficiency and outlet conditions over a range of flow rates, and (3) measure the thrust performance of a vaporizer/resistojet thruster assembly. A laboratory model of a forced-flow, once-through water vaporizer employing a porous heat exchange medium was built and characterized over a range of flow rates and power levels of interest for application to water resistojets. In a test during which the vaporizer was rotated about a horizontal axis normal to its own axis, the outlet temperature and mass flow rate through the vaporizer remained steady. Throttlability to 30 percent of the maximum flow rate tested was demonstrated. The measured thermal efficiency of the vaporizer was near 0.9 for all tests. The water vaporizer was integrated with an engineering model multipropellant resistojet. Performance of the vaporizer/thruster assembly was measured over a narrow range of operating conditions. The maximum specific impulse measured was 234 s at a mass flow rate and specific power level (vaporizer and thruster combined) of 154 x 10(exp-6)kg/s and 6.8 MJ/kg, respectively.

Site characterization at the Rabbit Valley Geophysical Performance Evaluation Range

NASA Astrophysics Data System (ADS)

Koppenjan, S.,; Martinez, M.

The United States Department of Energy (US DOE) is developing a Geophysical Performance Evaluation Range (GPER) at Rabbit Valley located 30 miles west of Grand Junction, Colorado. The purpose of the range is to provide a test area for geophysical instruments and survey procedures. Assessment of equipment accuracy and resolution is accomplished through the use of static and dynamic physical models. These models include targets with fixed configurations and targets that can be re-configured to simulate specific specifications. Initial testing (1991) combined with the current tests at the Rabbit Valley GPER will establish baseline data and will provide performance criteria for the development of geophysical technologies and techniques. The US DOE's Special Technologies Laboratory (STL) staff has conducted a Ground Penetrating Radar (GPR) survey of the site with its stepped FM-CW GPR. Additionally, STL contracted several other geophysical tests. These include an airborne GPR survey incorporating a 'chirped' FM-CW GPR system and a magnetic survey with a surfaced-towed magnetometer array unit Ground-based and aerial video and still frame pictures were also acquired. STL compiled and analyzed all of the geophysical maps and created a site characterization database. This paper discusses the results of the multi-sensor geophysical studies performed at Rabbit Valley and the future plans for the site.

Site characterization at the Rabbit Valley Geophysical Performance Evaluation Range

DOE Office of Scientific and Technical Information (OSTI.GOV)

Koppenjan, S,; Martinez, M.

1994-06-01

The United States Department of Energy (US DOE) is developing a Geophysical Performance Evaluation Range (GPER) at Rabbit Valley located 30 miles west of Grand Junction, Colorado. The purpose of the range is to provide a test area for geophysical instruments and survey procedures. Assessment of equipment accuracy and resolution is accomplished through the use of static and dynamic physical models. These models include targets with fixed configurations and targets that can be re-configured to simulate specific specifications. Initial testing (1991) combined with the current tests at the Rabbit Valley GPER will establish baseline data and will provide performance criteriamore » for the development of geophysical technologies and techniques. The US DOE`s Special Technologies Laboratory (STL) staff has conducted a Ground Penetrating Radar (GPR) survey of the site with its stepped FM-CW GPR. Additionally, STL contracted several other geophysical tests. These include an airborne GPR survey incorporating a ``chirped`` FM-CW GPR system and a magnetic survey with a surfaced-towed magnetometer array unit Ground-based and aerial video and still frame pictures were also acquired. STL compiled and analyzed all of the geophysical maps and created a site characterization database. This paper discusses the results of the multi-sensor geophysical studies performed at Rabbit Valley and the future plans for the site.« less

Heat, chloride, and specific conductance as ground water tracers near streams

USGS Publications Warehouse

Cox, M.H.; Su, G.W.; Constantz, J.

2007-01-01

Commonly measured water quality parameters were compared to heat as tracers of stream water exchange with ground water. Temperature, specific conductance, and chloride were sampled at various frequencies in the stream and adjacent wells over a 2-year period. Strong seasonal variations in stream water were observed for temperature and specific conductance. In observation wells where the temperature response correlated to stream water, chloride and specific conductance values were similar to stream water values as well, indicating significant stream water exchange with ground water. At sites where ground water temperature fluctuations were negligible, chloride and/or specific conductance values did not correlate to stream water values, indicating that ground water was not significantly influenced by exchange with stream water. Best-fit simulation modeling was performed at two sites to derive temperature-based estimates of hydraulic conductivities of the alluvial sediments between the stream and wells. These estimates were used in solute transport simulations for a comparison of measured and simulated values for chloride and specific conductance. Simulation results showed that hydraulic conductivities vary seasonally and annually. This variability was a result of seasonal changes in temperature-dependent hydraulic conductivity and scouring or clogging of the streambed. Specific conductance fits were good, while chloride data were difficult to fit due to the infrequent (quarterly) stream water chloride measurements during the study period. Combined analyses of temperature, chloride, and specific conductance led to improved quantification of the spatial and temporal variability of stream water exchange with shallow ground water in an alluvial system. ?? 2007 National Ground Water Association.

Water-chemistry and chloride fluctuations in the Upper Floridan Aquifer in the Port Royal Sound area, South Carolina, 1917-93

USGS Publications Warehouse

Landmeyer, J.E.; Belval, D.L.

1996-01-01

Withdrawal of water from the Upper Floridan aquifer south of Port Royal Sound in Beaufort and Jasper Counties, South Carolina, has lowered water levels and reversed the hydraulic gradient beneath Hilton Head Island, South Carolina. Ground water that had previously discharged at the Sound is now being deflected southwest, toward withdrawals located near the city of Savannah, Georgia, and the island of Hilton Head. The reversal of this hydraulic gradient and the decline of water levels have caused saltwater in the Upper Floridan aquifer north of Port Royal Sound to begin moving southwest, toward water-supply wells for the town of Hilton Head and toward industries pumping ground water near Savannah. Analytical results from ground-water samples collected from wells in the Upper Floridan aquifer beneath and adjacent to Port Royal Sound show two plumes in the aquifer with chloride concentrations above the drinking- water standard. One plume of high chloride concentration extends slightly south of the theoretical predevelopment location of the steady- state freshwater-saltwater interface as indicated by numerical modeling. The other plume is present beneath the town of Port Royal, where the upper confining unit above the Upper Floridan aquifer is thin or absent. In these areas, the decline in water levels caused by ground-water withdrawals may have made it possible for water from tidal creeks to enter the Upper Floridan aquifer. Many wells completed in the upper permeable zone of the Upper Floridan aquifer show a distinct specific- conductance profile. One non-producing, monitoring well on Hilton Head Island (BFT-1810) was selected to depict a worst-case scenario to examine the short- and long-term water-chemistry and chloride fluctuations in the aquifer. Specific conductance was monitored at depths of 170, 190, and 200 feet below the top of the well casing. The specific conductance measured in 1987 ranged from approximately 450 microsiemens per centimeter near the top of the Upper Floridan aquifer to 1,500 microsiemens per centimeter near the lower, less permeable zone. Short-term fluctuations in conductance were measured at each probe and were found to be related to water-level fluctuations in the well caused by tidal cycles. The conductance varied regularly up to 100 microsiemens per centimeter, with an increasing time lag between high and low tides and low and high specific conductance for progressively shallower depths. Well BFT-1810 was monitored for specific conductance and water levels from October 1987 through September 1993. Specific conductance at the 170-foot probe showed little long-term change, while the 190- and the 200-foot probes showed long-term increases to approximately 4,000 and 10,000 microsiemens per centimeter, respectively. This well is located closest to one of the two plumes of saltwater delineated in the Upper Floridan aquifer, and the long-term chloride increases are a result of the movement of saltwater in the Upper Floridan aquifer toward Hilton Head Island under the influence of regional ground-water withdrawals.

Deficits in general emotion regulation skills-Evidence of a transdiagnostic factor.

PubMed

Lukas, Christian Aljoscha; Ebert, David Daniel; Fuentes, Hugo Trevisi; Caspar, Franz; Berking, Matthias

2017-12-15

Deficits in emotion regulation (ER) skills are discussed as a transdiagnostic factor contributing to the development and maintenance of various mental disorders. However, systematic comparisons of a broad range of ER skills across diagnostic groups that are based on comparable definitions and measures of ER are still rare. Therefore, we conducted two studies assessing a broad range of ER skills with the Emotion Regulation Skills Questionnaire in individuals meeting criteria for mental disorders (N 1  = 1448; N 2  = 137) and in a general population sample (N = 214). Consistent across the two studies, participants in the clinical samples reported lower general and lower specific ER skills than participants in the general population sample. Also consistent across the two studies, diagnostic subgroups of the clinical samples differed significantly with regard to general and specific ER skills. The studies provide evidence that deficits in ER are associated with various forms of psychopathology. However, mental disorders seem to differ with regard to how strongly they are linked to ER skills. © 2017 Wiley Periodicals, Inc.

Different Variations of Néel Temperature TN and Kondo Temperature TK in the Alloy System Ce(Ru1-xOsx)2Al10 under Uniaxial Pressure

NASA Astrophysics Data System (ADS)

Takeuchi, Takashi; Hayashi, Kyosuke; Umeo, Kazunori; Takabatake, Toshiro

2018-05-01

We report magnetic, transport, and specific-heat measurements for single crystals of the antiferromagnetic (AFM) Kondo semiconductor alloy series Ce(Ru1-xOsx)2Al10 (0 ≤ x ≤ 1), which crystallize into an orthorhombic structure. The specific-heat and resistivity data show that the isoelectronic substitution does not damage the hybridization gap or the AFM transition. The Kondo temperature TK increases linearly with x, whereas the Néel temperature TN exhibits a maximum value of 29.2 K for x = 0.71. Under increasing uniaxial pressure P || a, TN increases for x = 0 but decreases for x = 1, while TK increases in the entire range of x. Under P || b, in contrast, TN increases steadily in the whole range of x while TK remains unchanged for each x. The strongly anisotropic change in TN indicates the presence of another mechanism to enhance TN in this system in addition to the anisotropic hybridization of the 4f state with conduction bands.

The specific absorption rate of tissues in rats exposed to electromagnetic plane waves in the frequency range of 0.05-5 GHz and SARwb in free-moving rats.

PubMed

Chen, Bingxin; Wang, Jiamin; Qi, Hongxin; Zhang, Jie; Chen, Shude; Wang, Xianghui

2017-03-01

As electromagnetic exposure experiments can only be performed on small animals, usually rats, research on the characteristics of specific absorption rate (SAR) distribution in the rat has received increasing interest. A series of calculations, which simulated the SAR in a male rat anatomical model exposed to electromagnetic plane waves ranging from 0.05 to 5 GHz with different incidence and polarization, were conducted. The whole-body-averaged SAR (SARwb) and the tissue-averaged SAR (SARavg) in 20 major tissues were determined. Results revealed that incidence has great impact on SAR in the rat at higher frequencies owing to the skin effect and the effect on SARavg in tissues is much more apparent than that on SARwb; while polarization plays an important role under lower frequencies. Not only the incidence, but also the polarization in the rat keeps changing when the rat is in free movement. Thus, this article discussed a convenient way to obtain relatively accurate SARwb in a free-moving rat.

Ion Speciation and Transport Properties of LiTFSI in 1,3-Dioxolane Solutions: A Case Study for Li-S Battery Applications.

PubMed

Raccichini, Rinaldo; Dibden, James W; Brew, Ashley; Owen, John R; García-Aráez, Nuria

2018-01-11

Lithium-sulfur battery is considered to be one of the main candidates for "post-lithium-ion" battery generation because of its high theoretical specific capacity and inherently low cost. The role of electrolyte is particularly important in this system, and remarkable battery performances have been reported by tuning the amount of salt in the electrolyte. To further understand the reasons for such improvements, we chose the lithium bis(trifluoromethanesulfonyl)imide in 1,3-dioxolane electrolyte as a model salt-solvent system for a systematic study of conductivity and viscosity over a wide range of concentration from 10 -5 up to 5 m. The experimental results, discussed and interpreted with reference to the theory of electrolyte conductance, lead to the conclusion that triple ion formation is responsible for the highest molal conductivity values before reaching the maximum at 1.25 m. At higher concentrations, the molal conductivity drops quickly because of a rapid increase in viscosity and the salt-solvent system can be treated as a diluted form of molten salt.

Driving-forces model on individual behavior in scenarios considering moving threat agents

NASA Astrophysics Data System (ADS)

Li, Shuying; Zhuang, Jun; Shen, Shifei; Wang, Jia

2017-09-01

The individual behavior model is a contributory factor to improve the accuracy of agent-based simulation in different scenarios. However, few studies have considered moving threat agents, which often occur in terrorist attacks caused by attackers with close-range weapons (e.g., sword, stick). At the same time, many existing behavior models lack validation from cases or experiments. This paper builds a new individual behavior model based on seven behavioral hypotheses. The driving-forces model is an extension of the classical social force model considering scenarios including moving threat agents. An experiment was conducted to validate the key components of the model. Then the model is compared with an advanced Elliptical Specification II social force model, by calculating the fitting errors between the simulated and experimental trajectories, and being applied to simulate a specific circumstance. Our results show that the driving-forces model reduced the fitting error by an average of 33.9% and the standard deviation by an average of 44.5%, which indicates the accuracy and stability of the model in the studied situation. The new driving-forces model could be used to simulate individual behavior when analyzing the risk of specific scenarios using agent-based simulation methods, such as risk analysis of close-range terrorist attacks in public places.

Differentiating high priority pathway-based toxicity from non ...

EPA Pesticide Factsheets

The ToxCast chemical screening approach enables the rapid assessment of large numbers of chemicals for biological effects, primarily at the molecular level. Adverse outcome pathways (AOPs) offer a means to link biomolecular effects with potential adverse outcomes at the level of the individual or population, thus enhancing the utility of the ToxCast effort for hazard assessment. Thus, efforts are underway to develop AOPs relevant to the pathway perturbations detected in ToxCast assays. However, activity (?‘hits’) determined for chemical-assay pairs may reflect target-specific activity relevant to a molecular initiating event of an AOP, or more generalized cell stress and cytotoxicity-mediated effects. Previous work identified a ?‘cytotoxic burst’ phenomenon wherein large numbers of assays begin to respond at or near concentrations that elicit cytotoxicity. The concentration range at which the “burst” occurs is definable, statistically. Consequently, in order to focus AOP development on the ToxCast assay targetswhich are most sensitive and relevant to pathway-specific effects, we conducted a meta-analysis to identify which assays were frequently responding at concentrations well below the cytotoxic burst. Assays were ranked by the fraction of chemical hits below the burst concentration range compared to the number of chemicals tested, resulting in a preliminary list of potentially important, target-specific assays. After eliminating cytotoxicity a

Characterising variation in wheat traits under hostile soil conditions in India

PubMed Central

Khokhar, Jaswant S.; Sareen, Sindhu; Tyagi, Bhudeva S.; Singh, Gyanendra; Chowdhury, Apurba K.; Dhar, Tapamay; Singh, Vinod; King, Ian P.; Young, Scott D.

2017-01-01

Intensive crop breeding has increased wheat yields and production in India. Wheat improvement in India typically involves selecting yield and component traits under non-hostile soil conditions at regional scales. The aim of this study is to quantify G*E interactions on yield and component traits to further explore site-specific trait selection for hostile soils. Field experiments were conducted at six sites (pH range 4.5–9.5) in 2013–14 and 2014–15, in three agro-climatic regions of India. At each site, yield and component traits were measured on 36 genotypes, representing elite varieties from a wide genetic background developed for different regions. Mean grain yields ranged from 1.0 to 5.5 t ha-1 at hostile and non-hostile sites, respectively. Site (E) had the largest effect on yield and component traits, however, interactions between genotype and site (G*E) affected most traits to a greater extent than genotype alone. Within each agro-climatic region, yield and component traits correlated positively between hostile and non-hostile sites. However, some genotypes performed better under hostile soils, with site-specific relationships between yield and component traits, which supports the value of ongoing site-specific selection activities. PMID:28604800

Reduced specificity in emotion judgment in people with autism spectrum disorder

PubMed Central

Wang, Shuo; Adolphs, Ralph

2017-01-01

There is a conflicting literature on facial emotion processing in autism spectrum disorder (ASD): both typical and atypical performance have been reported, and inconsistencies in the literature may stem from different processes examined (emotion judgment, face perception, fixations) as well as differences in participant populations. Here we conducted a detailed investigation of the ability to discriminate graded emotions shown in morphs of fear-happy faces, in a well-characterized high-functioning sample of participants with ASD and matched controls. Signal detection approaches were used in the analyses, and concurrent high-resolution eye-tracking was collected. Although people with ASD had typical thresholds for categorical fear and confidence judgments, their psychometric specificity to detect emotions across the entire range of intensities was reduced. However, fixation patterns onto the stimuli were typical and could not account for the reduced specificity of emotion judgment. Together, our results argue for a subtle and specific deficit in emotion perception in ASD that, from a signal detection perspective, is best understood as a reduced specificity due to increased noise in central processing of the face stimuli. PMID:28343960

Comparison of daily and weekly precipitation sampling efficiencies using automatic collectors

USGS Publications Warehouse

Schroder, L.J.; Linthurst, R.A.; Ellson, J.E.; Vozzo, S.F.

1985-01-01

Precipitation samples were collected for approximately 90 daily and 50 weekly sampling periods at Finley Farm, near Raleigh, North Carolina from August 1981 through October 1982. Ten wet-deposition samplers (AEROCHEM METRICS MODEL 301) were used; 4 samplers were operated for daily sampling, and 6 samplers were operated for weekly-sampling periods. This design was used to determine if: (1) collection efficiences of precipitation are affected by small distances between the Universal (Belfort) precipitation gage and collector; (2) measurable evaporation loss occurs and (3) pH and specific conductance of precipitation vary significantly within small distances. Average collection efficiencies were 97% for weekly sampling periods compared with the rain gage. Collection efficiencies were examined by seasons and precipitation volume. Neither factor significantly affected collection efficiency. No evaporation loss was found by comparing daily sampling to weekly sampling at the collection site, which was classified as a subtropical climate. Correlation coefficients for pH and specific conductance of daily samples and weekly samples ranged from 0.83 to 0.99.Precipitation samples were collected for approximately 90 daily and 50 weekly sampling periods at Finley farm, near Raleigh, North Carolina from August 1981 through October 1982. Ten wet-deposition samplers were used; 4 samplers were operated for daily sampling, and 6 samplers were operated for weekly-sampling periods. This design was used to determine if: (1) collection efficiencies of precipitation are affected by small distances between the University (Belfort) precipitation gage and collector; (2) measurable evaporation loss occurs and (3) pH and specific conductance of precipitation vary significantly within small distances.

Numerical simulation of ground-water flow in the central part of the western San Joaquin Valley, California

USGS Publications Warehouse

Belitz, Kenneth; Phillips, Steven P.; Gronberg, Jo Ann M.

1993-01-01

The occurrence of selenium in agricultural drain water in the central part of the western San Joaquin Valley, California, has focused concern on strategies for managing shallow, saline ground water. To assess alternatives to agricultural drains, a three-dimensional, finite-difference numerical model of the regional groundwater flow system was developed. This report documents the mathematical approach used to model the flow system, the data base on which the model is based, and the methods used to calibrate the model. The 550-square-mile study area includes parts of the Panoche Creek alluvial fan and parts of the Little Panoche Creek and Cantua Creek alluvial fans. The model simulates transient flow in the semiconfined and confined zones above and below the Corcoran Clay Member of the Tulare Formation of Pleistocene age. The model incorporates areally distributed ground-water recharge, areally and vertically distributed pumping, regional-collector drains in the Wesdands Water District (operative from 1980 to 1985), on-farm drains in parts of the Panoche, Broadview, and Firebaugh Water Districts, and bare-soil evaporation (which occurs if the water table is within 7 feet of land surface). The model also incorporates texture-based estimates of hydraulic conductivity, where texture is defined as the fraction of coarse-grained deposits present in a given subsurface interval. The numerical model was developed using hydrologic data from 1972 to 1988. Most of the parameters incorporated into the model were evaluated independently of the model, including system geometry, the distribution of texture, the altitudes of the water table and potentiometric surface of the confined zone in 1972 (initial condition), the hydraulic conductivity of coarse-grained deposits derived from the Coast Ranges, the hydraulic conductivity of coarse-grained deposits derived from the Sierra Nevada, specific storage, recharge, pumping, and parameters needed to incorporate drains and bare-soil evaporation. Four parameters were calibration variables: the hydraulic conductivity of fine-grained deposits in the semiconfined zone, the hydraulic conductivity of the Corcoran Clay Member, specific yield, and the transmissivity of the confined zone. The model was calibrated in two phases. In the first phase, a steady-state model of the ground-water flow system in 1984 was used to constrain the relation between the hydraulic conductivity of fine-grained deposits in the semiconfined zone and the hydraulic conductivity of the Corcoran Clay Member, thus reducing the number of independent variables from four to three. In the second phase of calibration, the change in altitude of the water table from 1972 to 1984, the change in altitude of the potentiometric surface of the confined zone from 1972 to 1984, and the number of model cells subject to bare-soil evaporation from 1972 to 1988 were used to evaluate the remaining three variables. The calibrated model reproduces the average change in water-table altitude (1972-84) to within 0.4 foot (average measured change 11.5 feet) and the average change in confined zone head (1972- 84) to within 19 feet (average measured change 120 feet). The simulated time-series record of the total number of model cells subject to bare-soil evaporation (each cell is 1 mile square) is within the range of the measured data. The measured values are at a minimum in October and a maximum in July. The October values ranged from 103 in 1972 to 132 in 1984 (the drains were closed in 1985) to 151 in 1988. The July values ranged from 144 in 1973 to 198 in 1984, to 204 in 1988. The simulated values ranged from 103 in 1972 to 161 in 1984, to 208 in 1988.

Electronic transport mechanism in intrinsic and doped nanocrystalline silicon films deposited by RF-magnetron sputtering at low temperature

NASA Astrophysics Data System (ADS)

Benlakehal, D.; Belfedal, A.; Bouizem, Y.; Sib, J. D.; Chahed, L.; Zellama, K.

2016-12-01

The dependence on the temperature range, T, of the electronic transport mechanism in intrinsic and doped hydrogenated nanocrystalline silicon films, deposited by radiofrequency-magnetron sputtering at low substrate temperature, has been studied. Electrical conductivity measurements σ(T) have been conducted on these films, as a function of temperature, in the 93-450 K range. The analysis of these results clearly shows a thermally activated conduction process in the 273-450 K range which allows us to estimate the associated activation energy as well as the preexponential conductivity factor. While, in the lower temperature range (T < 273 K), a non-ohmic behavior is observed for the conductivity changes. The conductivity σ(T) presents a linear dependence on (T-1/4) , and a hopping mechanism is suggested to explain these results. By using the Percolation theory, further information can be gained about the density of states near the Fermi level as well as the range and the hopping energy.

7 CFR 1484.34 - Must Cooperators adhere to specific standards of ethical conduct?

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false Must Cooperators adhere to specific standards of ethical conduct? 1484.34 Section 1484.34 Agriculture Regulations of the Department of Agriculture... Cooperators adhere to specific standards of ethical conduct? (a) A Cooperator shall conduct its business in...

7 CFR 1484.34 - Must Cooperators adhere to specific standards of ethical conduct?

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 10 2014-01-01 2014-01-01 false Must Cooperators adhere to specific standards of ethical conduct? 1484.34 Section 1484.34 Agriculture Regulations of the Department of Agriculture... specific standards of ethical conduct? (a) A Cooperator shall conduct its business in accordance with the...

7 CFR 1484.34 - Must Cooperators adhere to specific standards of ethical conduct?

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 10 2013-01-01 2013-01-01 false Must Cooperators adhere to specific standards of ethical conduct? 1484.34 Section 1484.34 Agriculture Regulations of the Department of Agriculture... specific standards of ethical conduct? (a) A Cooperator shall conduct its business in accordance with the...

7 CFR 1484.34 - Must Cooperators adhere to specific standards of ethical conduct?

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 10 2012-01-01 2012-01-01 false Must Cooperators adhere to specific standards of ethical conduct? 1484.34 Section 1484.34 Agriculture Regulations of the Department of Agriculture... specific standards of ethical conduct? (a) A Cooperator shall conduct its business in accordance with the...

Habitat-specific differences alter traditional biogeographic patterns of life history in a climate-change induced range expansion.

PubMed

Riley, Megan E; Griffen, Blaine D

2017-01-01

Range shifts and expansions resulting from global climate change have the potential to create novel communities with unique plant-animal interactions. Organisms expanding their range into novel biotic and abiotic environments may encounter selection pressures that alter traditional biogeographic patterns of life history traits. Here, we used field surveys to examine latitudinal patterns of life history traits in a broadly distributed ectotherm (mangrove tree crab Aratus pisonii) that has recently experienced a climate change-induced range expansion into a novel habitat type. Additionally, we conducted laboratory and field experiments to investigate characteristics associated with these life history traits (e.g. fecundity, offspring quality, and potential selection pressures). We compared these characteristics in native mangrove habitats in which the species has historically dwelled and novel salt marsh habitats into which the species has recently expanded its range. Consistent with traditional biogeographic concepts (i.e. Bergmann's clines), size at maturity and mean body size of reproductive females increased with latitude within the native habitat. However, they decreased significantly in novel habitats at the highest latitudes of the species' range, which was consistent with habitat-specific differences in both biotic (predation) and abiotic (temperature) selection pressures. Although initial maternal investment (egg volume and weight) did not differ between habitats, fecundity was lower in novel habitats as a result of differences in size at reproduction. Offspring quality, as measured by larval starvation resistance, was likewise diminished in novel habitats relative to native habitats. These differences in offspring quality may have enduring consequences for species success and persistence in novel habitats. Life history characteristics such as those investigated here are fundamental organismal traits; consequently, understanding the potential impacts of climate change responses on latitudinal patterns of these traits is key to understanding climate change impacts on natural systems.

Examination of two methods of describing the thermodynamic properties of oxygen near the critical point

NASA Technical Reports Server (NTRS)

Rees, T. H.; Suttles, J. T.

1972-01-01

A computer study was conducted to compare the numerical behavior of two approaches to describing the thermodynamic properties of oxygen near the critical point. Data on the relative differences between values of specific heats at constant pressure (sub p) density, and isotherm and isochor derivatives of the equation of state are presented for selected supercritical pressures at temperatures in the range 100 to 300 K. The results of a more detailed study of the sub p representations afforded by the two methods are also presented.

Aerodynamic studies of delta-wing shuttle orbiters. Part 1: Low speed

NASA Technical Reports Server (NTRS)

Freeman, D. C., Jr.; Ellison, J. C.

1972-01-01

Numerous wind tunnel tests conducted on the evolving delta-wing orbiters have generated a fairly large aerodynamic data base over the entire entry operation range of these vehicles. A limited assessment is made of some of the aerodynamics of the current HO type orbiters, and several specific problem areas selected from the broad data base are discussed. These include, from a subsonic viewpoint, discussions of trim drag effect; effects of the installation of main rocket engine nozzles, OMS and RCS packages, Reynolds number effects, lateral-directional stability characteristics, and landing characteristics.

The 4.5 inch diameter IPV Ni-H2 cell development program

NASA Technical Reports Server (NTRS)

Miller, L.

1986-01-01

Interest in larger capacity Ni-H2 battery cells for space applications has resulted in the initiation of a development/qualification/production program. Cell component design was completed and component hardware fabricated and/or delivered. Finished cell design projections demonstrate favorable specific energies in the range of 70 to 75 Whr/Kg (32 to 34 Whr/Lb) for capacities of 100 to 250 Ah. It is further planned during this effort to evaluate the advanced cell design technology which has evolved from the work conducted at the NASA/Lewis Research Center.

The 4.5 inch diameter IPV Ni-H2 cell development program

NASA Astrophysics Data System (ADS)

Miller, L.

1986-09-01

Interest in larger capacity Ni-H2 battery cells for space applications has resulted in the initiation of a development/qualification/production program. Cell component design was completed and component hardware fabricated and/or delivered. Finished cell design projections demonstrate favorable specific energies in the range of 70 to 75 Whr/Kg (32 to 34 Whr/Lb) for capacities of 100 to 250 Ah. It is further planned during this effort to evaluate the advanced cell design technology which has evolved from the work conducted at the NASA/Lewis Research Center.

Towards practical application of sensors for monitoring animal health; design and validation of a model to detect ketosis.

PubMed

Steensels, Machteld; Maltz, Ephraim; Bahr, Claudia; Berckmans, Daniel; Antler, Aharon; Halachmi, Ilan

2017-05-01

The objective of this study was to design and validate a mathematical model to detect post-calving ketosis. The validation was conducted in four commercial dairy farms in Israel, on a total of 706 multiparous Holstein dairy cows: 203 cows clinically diagnosed with ketosis and 503 healthy cows. A logistic binary regression model was developed, where the dependent variable is categorical (healthy/diseased) and a set of explanatory variables were measured with existing commercial sensors: rumination duration, activity and milk yield of each individual cow. In a first validation step (within-farm), the model was calibrated on the database of each farm separately. Two thirds of the sick cows and an equal number of healthy cows were randomly selected for model validation. The remaining one third of the cows, which did not participate in the model validation, were used for model calibration. In order to overcome the random selection effect, this procedure was repeated 100 times. In a second (between-farms) validation step, the model was calibrated on one farm and validated on another farm. Within-farm accuracy, ranging from 74 to 79%, was higher than between-farm accuracy, ranging from 49 to 72%, in all farms. The within-farm sensitivities ranged from 78 to 90%, and specificities ranged from 71 to 74%. The between-farms sensitivities ranged from 65 to 95%. The developed model can be improved in future research, by employing other variables that can be added; or by exploring other models to achieve greater sensitivity and specificity.

Maps and grids of hydrogeologic information created from standardized water-well drillers’ records of the glaciated United States

USGS Publications Warehouse

Bayless, E. Randall; Arihood, Leslie D.; Reeves, Howard W.; Sperl, Benjamin J.S.; Qi, Sharon L.; Stipe, Valerie E.; Bunch, Aubrey R.

2017-01-18

As part of the National Water Availability and Use Program established by the U.S. Geological Survey (USGS) in 2005, this study took advantage of about 14 million records from State-managed collections of water-well drillers’ records and created a database of hydrogeologic properties for the glaciated United States. The water-well drillers’ records were standardized to be relatively complete and error-free and to provide consistent variables and naming conventions that span all State boundaries.Maps and geospatial grids were developed for (1) total thickness of glacial deposits, (2) total thickness of coarse-grained deposits, (3) specific-capacity based transmissivity and hydraulic conductivity, and (4) texture-based estimated equivalent horizontal and vertical hydraulic conductivity and transmissivity. The information included in these maps and grids is required for most assessments of groundwater availability, in addition to having applications to studies of groundwater flow and transport. The texture-based estimated equivalent horizontal and vertical hydraulic conductivity and transmissivity were based on an assumed range of hydraulic conductivity values for coarse- and fine-grained deposits and should only be used with complete awareness of the methods used to create them. However, the maps and grids of texture-based estimated equivalent hydraulic conductivity and transmissivity may be useful for application to areas where a range of measured values is available for re-scaling.Maps of hydrogeologic information for some States are presented as examples in this report but maps and grids for all States are available electronically at the project Web site (USGS Glacial Aquifer System Groundwater Availability Study, http://mi.water.usgs.gov/projects/WaterSmart/Map-SIR2015-5105.html) and the Science Base Web site, https://www.sciencebase.gov/catalog/item/58756c7ee4b0a829a3276352.

Development of a Conductivity Sensor for Monitoring Groundwater Resources to Optimize Water Management in Smart City Environments.

PubMed

Parra, Lorena; Sendra, Sandra; Lloret, Jaime; Bosch, Ignacio

2015-08-26

The main aim of smart cities is to achieve the sustainable use of resources. In order to make the correct use of resources, an accurate monitoring and management is needed. In some places, like underground aquifers, access for monitoring can be difficult, therefore the use of sensors can be a good solution. Groundwater is very important as a water resource. Just in the USA, aquifers represent the water source for 50% of the population. However, aquifers are endangered due to the contamination. One of the most important parameters to monitor in groundwater is the salinity, as high salinity levels indicate groundwater salinization. In this paper, we present a specific sensor for monitoring groundwater salinization. The sensor is able to measure the electric conductivity of water, which is directly related to the water salinization. The sensor, which is composed of two copper coils, measures the magnetic field alterations due to the presence of electric charges in the water. Different salinities of the water generate different alterations. Our sensor has undergone several tests in order to obtain a conductivity sensor with enough accuracy. First, several prototypes are tested and are compared with the purpose of choosing the best combination of coils. After the best prototype was selected, it was calibrated using up to 30 different samples. Our conductivity sensor presents an operational range from 0.585 mS/cm to 73.8 mS/cm, which is wide enough to cover the typical range of water salinities. With this work, we have demonstrated that it is feasible to measure water conductivity using solenoid coils and that this is a low cost application for groundwater monitoring.

Development of a Conductivity Sensor for Monitoring Groundwater Resources to Optimize Water Management in Smart City Environments

PubMed Central

Parra, Lorena; Sendra, Sandra; Lloret, Jaime; Bosch, Ignacio

2015-01-01

The main aim of smart cities is to achieve the sustainable use of resources. In order to make the correct use of resources, an accurate monitoring and management is needed. In some places, like underground aquifers, access for monitoring can be difficult, therefore the use of sensors can be a good solution. Groundwater is very important as a water resource. Just in the USA, aquifers represent the water source for 50% of the population. However, aquifers are endangered due to the contamination. One of the most important parameters to monitor in groundwater is the salinity, as high salinity levels indicate groundwater salinization. In this paper, we present a specific sensor for monitoring groundwater salinization. The sensor is able to measure the electric conductivity of water, which is directly related to the water salinization. The sensor, which is composed of two copper coils, measures the magnetic field alterations due to the presence of electric charges in the water. Different salinities of the water generate different alterations. Our sensor has undergone several tests in order to obtain a conductivity sensor with enough accuracy. First, several prototypes are tested and are compared with the purpose of choosing the best combination of coils. After the best prototype was selected, it was calibrated using up to 30 different samples. Our conductivity sensor presents an operational range from 0.585 mS/cm to 73.8 mS/cm, which is wide enough to cover the typical range of water salinities. With this work, we have demonstrated that it is feasible to measure water conductivity using solenoid coils and that this is a low cost application for groundwater monitoring. PMID:26343653

Calculating Permittivity and Dielectric Loss Frequency Spectra for Aqueous Electrolyte Solutions

NASA Astrophysics Data System (ADS)

Odinaev, S.; Makhmadbegov, R. S.

2018-01-01

Analytic expressions for dielectric permittivity factor ɛ1(ω) and dielectric dissipation factor ɛ2(ω) of electrolyte solutions are obtained, based on the ratio between complex factors of dielectric permittivity and specific conductivity. The range of frequency dispersion of dynamic factors ɛ1(ω) and ɛ2(ω) for aqueous solutions of LiCl, NaCl, KCl, and CsCl is considered. Numerical calculations are performed for friction coefficients β a and β b ; relaxation times τ a , τ b , and τ ab ; and factors ɛ1(ω) and ɛ2(ω) in a wide range of variation for ρ; concentration c; temperature T; and frequencies ω. The resulting theoretically calculated ɛ1(ω) and ɛ2(ω) values and the Cole-Cole diagram are in quantitative agreement with experimental data.

Water-quality investigation, Salinas River, California

USGS Publications Warehouse

Irwin, G.A.

1976-01-01

Concentrations of dissolved solids in the Salinas River, California, are variable and range from 164 to 494 milligrams per liter near Bradley and from 170 to 1,090 milligrams per liter near Spreckels. Higher concentrations near Spreckels are caused mainly by sewage inflow about 150 feet (50 meters) upstream. Concentrations of nitrogen, phosphorus, total organic carbon, selected trace elements, and pesticides also generally increase downstream from Pozo to Spreckels and are related to sewage effluent; however, high concentrations occur elsewhere in the river. Specific conductance and water discharge regression results indicate that relations were all significant at the 1-percent probability level at Paso Robles, Bradley, and Spreckels with the explained variance ranging from 66 to 74 percent. Concentations of nitrogen, phosphorus, total organic carbon, and trace elements are only infrequently related to water discharge. (Woodard-USGS)

Appendix 3 Summary of Field Sampling and Analytical Methods with Bibliography

EPA Science Inventory

Conductivity and Specific conductance are measures of the ability of water to conduct an electric current, and are a general measure of stream-water quality. Conductivity is affected by temperature, with warmer water having a greater conductivity. Specific conductance is the te...

Evaluation of the effects of coal-mine reclamation on water quality in Big Four Hollow near Lake Hope, southeastern Ohio

USGS Publications Warehouse

Nichols, V.E.

1985-01-01

A subsurface clay dike and mine-entrance hydraulic seals were constructed from July 1979 through May 1980 by the Ohio Department if Natural Resources, Division of Reclamation to reduce acidic mine drainage from abandoned drift-mine complex 88 into Big Four Hollow Creek. Big Four Hollow Creek flows into Sandy Run--the major tributary to Lake Hope. A data-collection program was established in 1979 by the U.S. Geological Survey to evaluate effects of drift-mine sealing on surface-water systems of the Big Four Hollow Creek and Sandy Run area just below the mine. Data collected by private consultants from 1970 through 1971 near the mouth of Big Four Hollow Creek (U.S. Geological Survey station 03201700) show that pH ranged from 2.7 to 4.8, with a median of 3.1. The calculated iron load was 50 pounds per day. Data collecetd near the mouth of Big Four Hollow Creek (station 03201700) from 1971 through 1979 (before dike construction) show the daily pH ranged from 2.1 to 6.7; the median was 3.6. The daily specific conduction ranged from 72 to 3,500 microsiements per centimeter at 25? Celsius and averaged 770. The estimated loads of chemical constituents were: Sulfate, 1,100 pounds per day: iron, 54 pounds per day: and manganese, 12 pounds per day. All postconstruction data collected at station 03201700 through the end of the project, May 1980 through June 30, 1983, show that the daily pH ranged from 2.4 to 7.7, with a median of 3.7. Daily specific conductance ranged from 87 to 3,200 microsiemens per centimeter and averaged 1,200. The estimated loads of chemical constituents for this period were: Sulfate, 1,000 pounds per day: iron, 44 pounds per day: and manganese, 16 pounds per day. Standard nonparametric statistical tests were performed on the data collected before and after reclamation. Differences at the 95-percent confidence level were found in the before- and after-reclamation data sets for specific conductance, aluminum, and manganese at station 03201700. Data collected during the first 6 months after reclamation indicated moderate improvement in water quality only because no highly mineralized water was leaking from the closed mine. Later, perhaps in Sepember 1980 increased hydraulic head behind the clay dike caused the mine water to seep out and degrade the stream-water quality. In order to investigate leakages, dye was injected into two wells that penetrated the closed mine complex 88. One injection revealed that the dye moved to a discharge point at a nearby mine entrance known to be connected to complex 88. No discharge of dye was detected as a result of dye injection into the other well during the project. Acidic mine water continues to seep from the closed mine complex 88. A definitive evaluation of the effects of reclamation on the area's water quality cannot be made until the hydrologic system stabilizes.

Universal DC Hall conductivity of Jain's state ν = N/2N +/- 1

NASA Astrophysics Data System (ADS)

Nguyen, Dung; Son, Dam

We present the Fermi-liquid theory of the fractional quantum Hall effect to describe Jain's states with filling fraction ν =N/2 N +/- 1 , that are near half filling. We derive the DC Hall conductivity σH (t) in closed form within the validity of our model. The results show that, without long range interaction, DC Hall conductivity has the universal form which doesn't depend on the detail of short range Landau's parameters Fn. When long range interaction is included, DC Hall conductivity depends on both long range interaction and Landau's parameters. We also analyze the relation between DC Hall conductivity and static structure factor. This work was supported by the Chicago MRSEC, which is funded by NSF through Grant DMR-1420709.

Sensitive photo-thermal response of graphene oxide for mid-infrared detection

NASA Astrophysics Data System (ADS)

Bae, Jung Jun; Yoon, Jung Hyun; Jeong, Sooyeon; Moon, Byoung Hee; Han, Joong Tark; Jeong, Hee Jin; Lee, Geon-Woong; Hwang, Ha Ryong; Lee, Young Hee; Jeong, Seung Yol; Lim, Seong Chu

2015-09-01

This study characterizes the effects of incident infrared (IR) radiation on the electrical conductivity of graphene oxide (GO) and examines its potential for mid-IR detection. Analysis of the mildly reduced GO (m-GO) transport mechanism near room temperature reveals variable range hopping (VRH) for the conduction of electrons. This VRH behavior causes the m-GO resistance to exhibit a strong temperature dependence, with a large negative temperature coefficient of resistance of approximately -2 to -4% K-1. In addition to this hopping transport, the presence of various oxygen-related functional groups within GO enhances the absorption of IR radiation significantly. These two GO material properties are synergically coupled and provoke a remarkable photothermal effect within this material; specifically, a large resistance drop is exhibited by m-GO in response to the increase in temperature caused by the IR absorption. The m-GO bolometer effect identified in this study is different from that exhibited in vanadium oxides, which require added gold-black films that function as IR absorbers owing to their limited IR absorption capability.This study characterizes the effects of incident infrared (IR) radiation on the electrical conductivity of graphene oxide (GO) and examines its potential for mid-IR detection. Analysis of the mildly reduced GO (m-GO) transport mechanism near room temperature reveals variable range hopping (VRH) for the conduction of electrons. This VRH behavior causes the m-GO resistance to exhibit a strong temperature dependence, with a large negative temperature coefficient of resistance of approximately -2 to -4% K-1. In addition to this hopping transport, the presence of various oxygen-related functional groups within GO enhances the absorption of IR radiation significantly. These two GO material properties are synergically coupled and provoke a remarkable photothermal effect within this material; specifically, a large resistance drop is exhibited by m-GO in response to the increase in temperature caused by the IR absorption. The m-GO bolometer effect identified in this study is different from that exhibited in vanadium oxides, which require added gold-black films that function as IR absorbers owing to their limited IR absorption capability. Electronic supplementary information (ESI) available. See DOI: 10.1039/c5nr04039f

Complex conductivity of oil-contaminated clayey soils

NASA Astrophysics Data System (ADS)

Deng, Y.; Revil, A.; Shi, X.

2017-12-01

Non-intrusive hydrogeophysical techniques have been wildly applied to detect organic contaminants because of the difference of electrical properties for contaminated soil. Among them, spectral induced polarization (SIP) has emerged as a promising tool for the identification of contamination due to its sensitivity to the chemistry of pore water, solid-fluid interfaces and fluid content. Previous works have investigated the influences of oil on the electrical signatures of porous media, which demonstrated the potentials of SIP in the detection of hydrocarbon contamination. However, few works have done on the SIP response of oil in clayey soils. In this study, we perform a set of SIP measurements on the clayey samples under different water saturations. These clayey soils are characterized by relatively high cation exchange capacity. The objective in this work is to test the empirical relationships between the three exponents, including the cementation exponent (m), the saturation exponent (n) and the quadrature conductivity exponent (p), which is expected to reduce the model parameters needed in geophysical and hydraulic properties predictions. Our results show that the complex conductivity are saturation dependent. The magnitude of both in-phase and quadrature conductivities generally decrease with decreasing water saturation. The shape of quadrature conductivity spectra slightly changes when water saturation decreases in some cases. The saturation exponent slightly increases with cation exchange capacity, specific surface area and clay content, with an average value around 2.05. Compared to saturation exponent, the quadrature conductivity exponent apparently increases with cation exchange capacity and specific surface area while has little to do with the clay content. Further, the results indicate that the quadrature conductivity exponent p does not strictly obey to p=n-1 as proposed by Vinegar and Waxman (1984). Instead, it mostly ranges between p=n-1.5 and p=n-0.5. The relationship between the saturation exponent n and the cementation exponent m is comprised between m=n and m=n-0.5.

Specificity and Engagement: Increasing ELSI s Relevance to Nano Scientists

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shumpert, Barry L.; Wolfe, Amy K.; Bjornstad, David J.

Scholars studying the ethical, legal, and social issues (ELSI) associated with emerging technologies maintain the importance of considering these issues throughout the research and development cycle, even during the earliest stages of basic research. Embedding these considerations within the scientific process requires communication between ELSI scholars and the community of physical scientists who are conducting that basic research. We posit that this communication can be effective on a broad scale only if it links societal issues directly to characteristics of the emerging technology that are relevant to the physical and natural scientists involved in research and development. In this article,more » we examine nano-ELSI literature from 2003 to 2010 to discern the degree to which it makes these types of explicit connections. We find that, while the literature identifies a wide range of issues of societal concern, it generally does so in a non-specific manner. It neither links societal issues to particular forms or characteristics of widely divergent nanotechnologies nor to any of the many potential uses to which those nanotechnologies may be put. We believe that these kinds of specificity are essential to those engaged in nano-scale research. We also compare the literature-based findings to observations from interviews we conducted with nanoscientists and conclude that ELSI scholars should add technical- and application-related forms of specificity to their work and their writings to enhance effectiveness and impact in communicating with one important target audience members of the nanoscale science community.« less

A Fundamental Study of Smoldering with Emphasis on Experimental Design for Zero-G

NASA Technical Reports Server (NTRS)

Fernandez-Pello, Carlos; Pagni, Patrick J.

1995-01-01

A research program to study smoldering combustion with emphasis on the design of an experiment to be conducted in the space shuttle was conducted at the Department of Mechanical Engineering, University of California, Berkeley. The motivation of the research is the interest in smoldering both as a fundamental combustion problem and as a serious fire risk. Research conducted included theoretical and experimental studies that have brought considerable new information about smolder combustion, the effect that buoyancy has on the process, and specific information for the design of a space experiment. Experiments were conducted at normal gravity, in opposed and forward mode of propagation and in the upward and downward direction to determine the effect and range of influence of gravity on smolder. Experiments were also conducted in microgravity, in a drop tower and in parabolic aircraft flights, where the brief microgravity periods were used to analyze transient aspects of the problem. Significant progress was made on the study of one-dimensional smolder, particularly in the opposed-flow configuration. These studies provided enough information to design a small-scale space-based experiment that was successfully conducted in the Spacelab Glovebox in the June 1992 USML-1/STS-50 mission of the Space Shuttle Columbia.

Quantifying surface roughness effects on phonon transport in silicon nanowires.

PubMed

Lim, Jongwoo; Hippalgaonkar, Kedar; Andrews, Sean C; Majumdar, Arun; Yang, Peidong

2012-05-09

Although it has been qualitatively demonstrated that surface roughness can reduce the thermal conductivity of crystalline Si nanowires (SiNWs), the underlying reasons remain unknown and warrant quantitative studies and analysis. In this work, vapor-liquid-solid (VLS) grown SiNWs were controllably roughened and then thoroughly characterized with transmission electron microscopy to obtain detailed surface profiles. Once the roughness information (root-mean-square, σ, correlation length, L, and power spectra) was extracted from the surface profile of a specific SiNW, the thermal conductivity of the same SiNW was measured. The thermal conductivity correlated well with the power spectra of surface roughness, which varies as a power law in the 1-100 nm length scale range. These results suggest a new realm of phonon scattering from rough interfaces, which restricts phonon transport below the Casimir limit. Insights gained from this study can help develop a more concrete theoretical understanding of phonon-surface roughness interactions as well as aid the design of next generation thermoelectric devices.

Nonlocal electrodynamics in Weyl semimetals

NASA Astrophysics Data System (ADS)

Rosenstein, B.; Kao, H. C.; Lewkowicz, M.

2017-02-01

Recently synthesized three-dimensional materials with Dirac spectrum exhibit peculiar electric transport qualitatively different from its two-dimensional analog, graphene. By neglecting impurity scattering, the real part of the conductivity is strongly frequency dependent, while the imaginary part is nonzero unlike in undoped, clean graphene. The Coulomb interaction between electrons is unscreened as in a dielectric and hence is long range. We demonstrate that the interaction correction renders the electrodynamics nonlocal on a mesoscopic scale. The longitudinal conductivity σL and the transverse conductivity σT are different in the long-wavelength limit and consequently the standard local Ohm's law description does not apply. This leads to several remarkable effects in optical response. The p -polarized light generates in these materials bulk plasmons as well as the transversal waves. At a specific frequency the two modes coincide, a phenomenon impossible in a local medium. For any frequency there is a Brewster angle where total absorption occurs, turning the Weyl semimetals opaque. The effect of the surface, including the Fermi arcs, is discussed.

The Impact of Biosampling Procedures on Molecular Data Interpretation*

PubMed Central

Sköld, Karl; Alm, Henrik; Scholz, Birger

2013-01-01

The separation between biological and technical variation without extensive use of technical replicates is often challenging, particularly in the context of different forms of protein and peptide modifications. Biosampling procedures in the research laboratory are easier to conduct within a shorter time frame and under controlled conditions as compared with clinical sampling, with the latter often having issues of reproducibility. But is the research laboratory biosampling really less variable? Biosampling introduces within minutes rapid tissue-specific changes in the cellular microenvironment, thus inducing a range of different pathways associated with cell survival. Biosampling involves hypoxia and, depending on the circumstances, hypothermia, circumstances for which there are evolutionarily conserved defense strategies in the range of species and also are relevant for the range of biomedical conditions. It remains unclear to what extent such adaptive processes are reflected in different biosampling procedures or how important they are for the definition of sample quality. Lately, an increasing number of comparative studies on different biosampling approaches, post-mortem effects and pre-sampling biological state, have investigated such immediate early biosampling effects. Commonalities between biosampling effects and a range of ischemia/reperfusion- and hypometabolism/anoxia-associated biological phenomena indicate that even small variations in post-sampling time intervals are likely to introduce a set of nonrandom and tissue-specific effects of experimental importance (both in vivo and in vitro). This review integrates the information provided by these comparative studies and discusses how an adaptive biological perspective in biosampling procedures may be relevant for sample quality issues. PMID:23382104

Anthropometry-based 24-h urinary creatinine excretion reference for Chinese children

PubMed Central

Wang, Wei; Du, Cong; Lin, Laixiang; Chen, Wen; Tan, Long; Shen, Jun; Pearce, Elizabeth N.; Zhang, Yixin; Gao, Min; Bian, Jianchao; Wang, Xiaoming; Zhang, Wanqi

2018-01-01

To establish 24-h urinary creatinine excretion reference ranges based on anthropometry in healthy Chinese children, a cross-sectional survey was conducted using twice-sampled 24-h urine and anthropometric variables. Age- and sex-specific 24-h creatinine excretion reference ranges (crude and related to individual anthropometric variables) were derived. During October 2013 and May 2014, urine samples were collected. Anthropometric variables were measured in the first survey. Data of 710 children (377 boys and 333 girls) aged 8–13 years who completed the study were analyzed. No significant difference was observed in 24-h urine volumes between the two samples (median [interquartile range): 855.0 [600.0–1272.0) mL vs. 900.0 [660.0–1220.0) mL, P = 0.277). The mean 24-h urine creatinine excretion was regarded as representative of absolute daily creatinine excretion in children. Sex-specific, body-weight-adjusted creatinine excretion reference values were 15.3 mg/kg/day (0.1353 mmol/kg/day) for boys and 14.3 mg/kg/day (0.1264 mmol/kg/day) for girls. Differences were significant between boys and girls within the same age group but not across different age groups within the same sex. Ideal 24-h creatinine excretion values for height were derived for potential determination of the creatinine height index. These data can serve as reference ranges to calculate ratios of analyte to creatinine. The creatinine height index can be used to assess somatic protein status. PMID:29791502

Low-temperature thermoelectric, galvanomagnetic, and thermodynamic properties of the type-I clathrate Ba8AuxSi46-x

NASA Astrophysics Data System (ADS)

Aydemir, U.; Candolfi, C.; Ormeci, A.; Oztan, Y.; Baitinger, M.; Oeschler, N.; Steglich, F.; Grin, Yu.

2011-11-01

Polycrystalline samples of the clathrate Ba8AuxSi46-x were synthesized for 0.2 ⩽ x ⩽ 10. The homogeneity range of the type-I clathrate phase was determined to be 3.63 ⩽ x ⩽ 6.10 after annealing at 900 °C, while a lower Au concentration (x ≈ 2.2) was obtained by steel-quenching. Quasisingle phase materials were obtained for 4.10 ⩽ x ⩽ 6.10. In this composition range, thermoelectric properties, including electrical resistivity, thermopower, and thermal conductivity, were investigated between 2 and 350 K. These experiments were complemented by low-temperature specific heat and Hall-effect measurements (2-300 K). First-principles calculations were carried out to determine the evolution of the electronic structure as a function of x. Both theoretical and experimental results evidence a progressive evolution, with the Au content, from a metallic-like behavior towards a highly doped semiconducting state which develops around x = 5.43. At this concentration, a crossover from n- to p-type conduction occurs, suggesting that the present system satisfies the Zintl-Klemm concept, which predicts a transition at x = 5.33. This crossover is traced by Hall-effect data indicating a dominant electronlike response for x ⩽ 5.43, which turns into a holelike signal at higher x values. Analysis of the data based on a single-parabolic-band model under the assumption of a single scattering mechanism of the charge carriers proved to adequately describe the transport properties in the compositional range investigated. Interestingly, the temperature dependence of the lattice thermal conductivity is strongly influenced by the Au concentration: the typical behavior of crystalline insulators in the n-type compounds evolves into a glasslike dependence in the p-type samples. The series Ba8AuxSi46-x thus provides an excellent testing ground for the interplay between crystal structure, electronic properties, and lattice thermal conductivity in type-I clathrates.

Using Ethical Reasoning to Amplify the Reach and Resonance of Professional Codes of Conduct in Training Big Data Scientists.

PubMed

Tractenberg, Rochelle E; Russell, Andrew J; Morgan, Gregory J; FitzGerald, Kevin T; Collmann, Jeff; Vinsel, Lee; Steinmann, Michael; Dolling, Lisa M

2015-12-01

The use of Big Data--however the term is defined--involves a wide array of issues and stakeholders, thereby increasing numbers of complex decisions around issues including data acquisition, use, and sharing. Big Data is becoming a significant component of practice in an ever-increasing range of disciplines; however, since it is not a coherent "discipline" itself, specific codes of conduct for Big Data users and researchers do not exist. While many institutions have created, or will create, training opportunities (e.g., degree programs, workshops) to prepare people to work in and around Big Data, insufficient time, space, and thought have been dedicated to training these people to engage with the ethical, legal, and social issues in this new domain. Since Big Data practitioners come from, and work in, diverse contexts, neither a relevant professional code of conduct nor specific formal ethics training are likely to be readily available. This normative paper describes an approach to conceptualizing ethical reasoning and integrating it into training for Big Data use and research. Our approach is based on a published framework that emphasizes ethical reasoning rather than topical knowledge. We describe the formation of professional community norms from two key disciplines that contribute to the emergent field of Big Data: computer science and statistics. Historical analogies from these professions suggest strategies for introducing trainees and orienting practitioners both to ethical reasoning and to a code of professional conduct itself. We include two semester course syllabi to strengthen our thesis that codes of conduct (including and beyond those we describe) can be harnessed to support the development of ethical reasoning in, and a sense of professional identity among, Big Data practitioners.

Consolidated fuel reprocessing program

NASA Astrophysics Data System (ADS)

1985-02-01

Improved processes and components for the Breeder Reprocessing Engineering Test (BRET) were identified and developed as well as the design, procurement and development of prototypic equipment. The integrated testing of process equipment and flowsheets prototypical of a pilot scale full reprocessing plant, and also for testing prototypical remote features of specific complex components in the system are provided. Information to guide the long range activities of the Consolidated Fuel Reprocessing Program (CERP), a focal point for foreign exchange activities, and support in specialized technical areas are described. Research and development activities in HTGR fuel treatment technology are being conducted. Head-end process and laboratory scale development efforts, as well as studies specific to HTGR fuel, are reported. The development of off-gas treatment processes has generic application to fuel reprocessing, progress in this work is also reported.

A study on pore-opening behaviors of graphite nanofibers by a chemical activation process.

PubMed

Kim, Byung-Joo; Lee, Young-Seak; Park, Soo-Jin

2007-02-15

In this work, porous graphite nanofibers (GNFs) were prepared by a KOH activation method in order to manufacture porous carbon nanofibers. The process was conducted in the activation temperature range of 900-1100 degrees C, and the KOH:GNFs ratio was fixed at 3.5:1. The textural properties of the porous carbons were analyzed using N2 adsorption isotherms at 77 K. The BET, D-R, and BJH equations were used to observe the specific surface areas and the micro- and mesopore structures, respectively. From the results, it was found that the textural properties, including the specific surface area and the pore volumes, were proportionally enhanced with increasing activation temperatures. However, the activation mechanisms showed quite significant differences between the samples activated at low and high temperatures.

Performance Data from a Wind-Tunnel Test of Two Main-rotor Blade Designs for a Utility-Class Helicopter

NASA Technical Reports Server (NTRS)

Singleton, Jeffrey D.; Yeager, William T., Jr.; Wilbur, Matthew L.

1990-01-01

An investigation was conducted in the NASA Langley Transonic Dynamics Tunnel to evaluate an advanced main rotor designed for use on a utility class helicopter, specifically the U.S. Army UH-60A Blackhawk. This rotor design incorporated advanced twist, airfoil cross sections, and geometric planform. For evaluation purposes, the current UH-60A main rotor was also tested and is referred to as the baseline blade set. A total of four blade sets were tested. One set of both the baseline and the advanced rotors were dynamically scaled to represent a full scale helicopter rotor blade design. The remaining advanced and baseline blade sets were not dynamically scaled so as to isolate the effects of structural elasticity. The investigation was conducted in hover and at rotor advance ratios ranging from 0.15 to 0.4 at a range of nominal test medium densities from 0.00238 to 0.009 slugs/cu ft. This range of densities, coupled with varying rotor lift and propulsive force, allowed for the simulation of several vehicle gross weight and density altitude combinations. Performance data are presented for all blade sets without analysis; however, cross referencing of data with flight condition may be useful to the analyst for validating aeroelastic theories and design methodologies as well as for evaluating advanced design parameters.

Specific Conductance in the Colorado River between Glen Canyon Dam and Diamond Creek, Northern Arizona, 1988-2007

USGS Publications Warehouse

Voichick, Nicholas

2008-01-01

The construction of Glen Canyon Dam, completed in 1963, resulted in substantial physical and biological changes to downstream Colorado River environments between Lake Powell and Lake Mead - an area almost entirely within Grand Canyon National Park, Ariz. In an effort to understand these changes, data have been collected to assess the condition of a number of downstream resources. In terms of measuring water quality, the collection of specific-conductance data is a cost-effective method for estimating salinity. Data-collection activities were initially undertaken by the Bureau of Reclamation's Glen Canyon Environmental Studies (1982-96); these efforts were subsequently transferred to the U.S. Geological Survey's Grand Canyon Monitoring and Research Center (1996 to the present). This report describes the specific-conductance dataset collected for the Colorado River between Glen Canyon Dam and Diamond Creek from 1988 to 2007. Data-collection and processing methods used during the study period are described, and time-series plots of the data are presented. The report also includes plots showing the relation between specific conductance and total dissolved solids. Examples of the use of specific conductance as a natural tracer of parcels of water are presented. Analysis of the data indicates that short-duration spikes and troughs in specific-conductance values lasting from hours to days are primarily the result of flooding in the Paria and Little Colorado Rivers, Colorado River tributaries below Glen Canyon Dam. Specific conductance also exhibits seasonal variations owing to changes in the position of density layers within the reservoir; these changes are driven by inflow hydrology, meteorological conditions, and background stratification. Longer term trends in Colorado River specific conductance are reflective of climatological conditions in the upper Colorado River Basin. For example, drought conditions generally result in an increase in specific conductance in Lake Powell. Therefore, the average annual specific conductance below Glen Canyon Dam is inversely related to the volume of water in Lake Powell.

Influences of internal resistance and specific surface area of electrode materials on characteristics of electric double layer capacitors

NASA Astrophysics Data System (ADS)

Suda, Yoshiyuki; Mizutani, Akitaka; Harigai, Toru; Takikawa, Hirofumi; Ue, Hitoshi; Umeda, Yoshito

2017-01-01

We fabricated electric double layer capacitors (EDLCs) using particulate and fibrous types of carbon nanomaterials with a wide range of specific surface areas and resistivity as an active material. The carbon nanomaterials used in this study are carbon nanoballoons (CNBs), onion-like carbon (OLC), and carbon nanocoils (CNCs). A commercially used activated carbon (AC) combined with a conductive agent was used as a comparison. We compared the EDLC performance using cyclic voltammetry (CV), galvanostatic charge/discharge testing, and electrochemical impedance spectroscopy (EIS). OLC showed a poor EDLC performance, although it has the lowest resistivity among the carbon nanomaterials. CNB, which has a 1/16 lower specific surface area than AC but higher specific surface area than CNC and OLC, had a higher specific capacitance than CNC and OLC. Moreover, at current densities of 1.5 Ag-1 and larger, the specific capacitance of the EDLC using CNB was almost the same as that using AC. Electrochemical impedance spectroscopy of the EDLCs revealed that the CNB and CNC electrodes had a much lower internal resistance than the AC electrode, which correlated with a low capacitance maintenance factor as the current density increased.

Background hydrologic information in potential lignite mining areas in north-central Mississippi, August 1984

USGS Publications Warehouse

Kalkhoff, S.J.

1985-01-01

The U.S. Geological Survey, in cooperation with the Mississippi Department of Natural Resources, Bureau of Geology, is conducting a hydrologic data collection program in potential lignite-producing areas in Mississippi. During the last two weeks of August 1984, hydrologic data were collected at 15 stream sites that drain potential lignite mining areas in Lafayette, Calhoun, and Yalobusha Counties. Main channel widths ranged from approximately 60 feet at three streams (Coon Creek near Toccopula, Muckaloon Creek near Tula, and Hurricane Creek near Velma) to approximately 120 feet at two streams (Potlockney Creek near Tula, and Savannah Creek near Bruce). Maximum water depths ranged from less than 1.0 foot at most streams to over 5.0 feet at sites on Potlockney Creek near Tula and McGill Creek near Sarepta. Stream discharge ranged from 0.32 cubic feet per second in Persimmon Creek near Bruce to 18.5 cubic feet per second in Puskus Creek near Etta. The specific conductance of stream water ranged from 25 to 160 microsiemens and dissolved solids concentrations ranged from 22 to 91 mg/L (milligrams per liter). Most major ion concentrations were less than 10 mg/L with the exception of calcium (11 mg/L), sodium (12 mg/L) and sulfate (18 mg/L) in the water of Persimmon Creek near Bruce. Dissolved oxygen concentrations were greater than 5.0 mg/L at all but one site. Turbidity values were generally less than 50 units. Nitrate plus nitrite concentrations were equal to or less than 0.10 mg/L in all streams except in Potlockney Creek near Tula where the concentration was 0.11 mg/L. Copper and selenium concentrations in the water at all sampling sites ranged from below the detection limits (1 microgram/g) to 4 micrograms/g (micrograms per gram) and mercury concentrations in bottom material samples ranged from less than 0.01 microgram/g to 0.15 microgram/g. (USGS)

Case finding of lifestyle and mental health disorders in primary care: validation of the ‘CHAT’ tool

PubMed Central

Goodyear-Smith, Felicity; Coupe, Nicole M; Arroll, Bruce; Elley, C Raina; Sullivan, Sean; McGill, Anne-Thea

2008-01-01

Background Primary care is accessible and ideally placed for case finding of patients with lifestyle and mental health risk factors and subsequent intervention. The short self-administered Case-finding and Help Assessment Tool (CHAT) was developed for lifestyle and mental health assessment of adult patients in primary health care. This tool checks for tobacco use, alcohol and other drug misuse, problem gambling, depression, anxiety and stress, abuse, anger problems, inactivity, and eating disorders. It is well accepted by patients, GPs and nurses. Aim To assess criterion-based validity of CHAT against a composite gold standard. Design of study Conducted according to the Standards for Reporting of Diagnostic Accuracy statement for diagnostic tests. Setting Primary care practices in Auckland, New Zealand. Method One thousand consecutive adult patients completed CHAT and a composite gold standard. Sensitivities, specificities, positive and negative predictive values, and likelihood ratios were calculated. Results Response rates for each item ranged from 79.6 to 99.8%. CHAT was sensitive and specific for almost all issues screened, except exercise and eating disorders. Sensitivity ranged from 96% (95% confidence interval [CI] = 87 to 99%) for major depression to 26% (95% CI = 22 to 30%) for exercise. Specificity ranged from 97% (95% CI = 96 to 98%) for problem gambling and problem drug use to 40% (95% CI = 36 to 45%) for exercise. All had high likelihood ratios (3–30), except exercise and eating disorders. Conclusion CHAT is a valid and acceptable case-finding tool for most common lifestyle and mental health conditions. PMID:18186993

Online alcohol interventions: a systematic review.

PubMed

White, Angela; Kavanagh, David; Stallman, Helen; Klein, Britt; Kay-Lambkin, Frances; Proudfoot, Judy; Drennan, Judy; Connor, Jason; Baker, Amanda; Hines, Emily; Young, Ross

2010-12-19

There has been a significant increase in the availability of online programs for alcohol problems. A systematic review of the research evidence underpinning these programs is timely. Our objective was to review the efficacy of online interventions for alcohol misuse. Systematic searches of Medline, PsycINFO, Web of Science, and Scopus were conducted for English abstracts (excluding dissertations) published from 1998 onward. Search terms were: (1) Internet, Web*; (2) online, computer*; (3) alcohol*; and (4) E\\effect*, trial*, random* (where * denotes a wildcard). Forward and backward searches from identified papers were also conducted. Articles were included if (1) the primary intervention was delivered and accessed via the Internet, (2) the intervention focused on moderating or stopping alcohol consumption, and (3) the study was a randomized controlled trial of an alcohol-related screen, assessment, or intervention. The literature search initially yielded 31 randomized controlled trials (RCTs), 17 of which met inclusion criteria. Of these 17 studies, 12 (70.6%) were conducted with university students, and 11 (64.7%) specifically focused on at-risk, heavy, or binge drinkers. Sample sizes ranged from 40 to 3216 (median 261), with 12 (70.6%) studies predominantly involving brief personalized feedback interventions. Using published data, effect sizes could be extracted from 8 of the 17 studies. In relation to alcohol units per week or month and based on 5 RCTs where a measure of alcohol units per week or month could be extracted, differential effect sizes to posttreatment ranged from 0.02 to 0.81 (mean 0.42, median 0.54). Pre-post effect sizes for brief personalized feedback interventions ranged from 0.02 to 0.81, and in 2 multi-session modularized interventions, a pre-post effect size of 0.56 was obtained in both. Pre-post differential effect sizes for peak blood alcohol concentrations (BAC) ranged from 0.22 to 0.88, with a mean effect size of 0.66. The available evidence suggests that users can benefit from online alcohol interventions and that this approach could be particularly useful for groups less likely to access traditional alcohol-related services, such as women, young people, and at-risk users. However, caution should be exercised given the limited number of studies allowing extraction of effect sizes, the heterogeneity of outcome measures and follow-up periods, and the large proportion of student-based studies. More extensive RCTs in community samples are required to better understand the efficacy of specific online alcohol approaches, program dosage, the additive effect of telephone or face-to-face interventions, and effective strategies for their dissemination and marketing.

Online Alcohol Interventions: A Systematic Review

PubMed Central

Kavanagh, David; Stallman, Helen; Klein, Britt; Kay-Lambkin, Frances; Proudfoot, Judy; Drennan, Judy; Connor, Jason; Baker, Amanda; Hines, Emily; Young, Ross

2010-01-01

Background There has been a significant increase in the availability of online programs for alcohol problems. A systematic review of the research evidence underpinning these programs is timely. Objectives Our objective was to review the efficacy of online interventions for alcohol misuse. Systematic searches of Medline, PsycINFO, Web of Science, and Scopus were conducted for English abstracts (excluding dissertations) published from 1998 onward. Search terms were: (1) Internet, Web*; (2) online, computer*; (3) alcohol*; and (4) E\\effect*, trial*, random* (where * denotes a wildcard). Forward and backward searches from identified papers were also conducted. Articles were included if (1) the primary intervention was delivered and accessed via the Internet, (2) the intervention focused on moderating or stopping alcohol consumption, and (3) the study was a randomized controlled trial of an alcohol-related screen, assessment, or intervention. Results The literature search initially yielded 31 randomized controlled trials (RCTs), 17 of which met inclusion criteria. Of these 17 studies, 12 (70.6%) were conducted with university students, and 11 (64.7%) specifically focused on at-risk, heavy, or binge drinkers. Sample sizes ranged from 40 to 3216 (median 261), with 12 (70.6%) studies predominantly involving brief personalized feedback interventions. Using published data, effect sizes could be extracted from 8 of the 17 studies. In relation to alcohol units per week or month and based on 5 RCTs where a measure of alcohol units per week or month could be extracted, differential effect sizes to posttreatment ranged from 0.02 to 0.81 (mean 0.42, median 0.54). Pre-post effect sizes for brief personalized feedback interventions ranged from 0.02 to 0.81, and in 2 multi-session modularized interventions, a pre-post effect size of 0.56 was obtained in both. Pre-post differential effect sizes for peak blood alcohol concentrations (BAC) ranged from 0.22 to 0.88, with a mean effect size of 0.66. Conclusions The available evidence suggests that users can benefit from online alcohol interventions and that this approach could be particularly useful for groups less likely to access traditional alcohol-related services, such as women, young people, and at-risk users. However, caution should be exercised given the limited number of studies allowing extraction of effect sizes, the heterogeneity of outcome measures and follow-up periods, and the large proportion of student-based studies. More extensive RCTs in community samples are required to better understand the efficacy of specific online alcohol approaches, program dosage, the additive effect of telephone or face-to-face interventions, and effective strategies for their dissemination and marketing. PMID:21169175

Channel degradation in southeastern Nebraska Rivers

USGS Publications Warehouse

Wahl, Kenneth L.; Weiss, Linda S.; ,

1995-01-01

Many stream channels in southeastern Nebraska were dredged and straightened during 1904-15. The resulting channels were both shorter and steeper than the original channels. Tests for time trends were conducted using the nonparametric Kendall tau test to see if the channels have responded to these changes. Tests were conducted on the stages associated with specific discharges and on measurement characteristics at gaging stations. Tests also were conducted on hydrologic forcing variables (annual mean precipitation, annual peak discharges, annual mean discharge, and annual mean base flows). The null hypothesis (that the data were free from trend) was rejected for stages associated with the mean of the annual discharges for 6 of 7 gaging stations in the study area, but was accepted for all 3 gages on the main stem of the Missouri River. The trends at the 6 streamflow gaging stations were for decreasing stages (degrading channels) for specific discharges. The rates of change ranged from about 0.2 to 0.5 m per decade. Mean stream bed elevations computed for individual discharge measurements at these streamflow gaging stations confirmed that the channels are degrading. However, neither the precipitation nor flow variables show evidence of trends. The tendency for the channels to degrade thus cannot be attributed to changes in runoff characteristics and are assumed to be a response to the channel modifications in the early 1900's. Indications are that the channels presently are continuing to degrade.

Al/ oil nanofluids inside annular tube: an experimental study on convective heat transfer and pressure drop

NASA Astrophysics Data System (ADS)

Jafarimoghaddam, Amin; Aberoumand, Sadegh; Javaherdeh, Kourosh; Arani, Ali Akbar Abbasian; Jafarimoghaddam, Reza

2018-04-01

In this work, an experimental study on nanofluid preparation stability, thermo-physical properties, heat transfer performance and friction factor of Al/ Oil nanofluids has been carried out. Electrical Explosion Wire ( E.E.W) which is one of the most reliable one-step techniques for nanofluids preparation has been used. An annular tube has been considered as the test section in which the outer tube was subject to a uniform heat flux boundary condition of about 204 W. The utilized nanofluids were prepared in three different volume concentrations of 0.011%, 0.044% and 0.171%. A wide range of parameters such as Reynolds number Prandtl number, viscosity, thermal conductivity, density, specific heat, convective heat transfer coefficient, Nusselt number and the friction factor have been studied. The experiment was conducted in relatively low Reynolds numbers of less than 160 and within a hydrodynamically fully-developed regime. According to the results, thermal conductivity, density and viscosity increased depending on the volume concentrations and working temperatures while the specific heat declined. More importantly, it was observed that convective heat transfer coefficient and Nusselt number enhanced by 28.6% and 16.4%, respectively, for the highest volume concentration. Finally, the friction factor (which plays an important role in the pumping power) was found to be increased around 18% in the volume fraction of 0.171%.

Aggregation of Adenovirus 2 in Source Water and Impacts on Disinfection by Chlorine

PubMed Central

Cromeans, Theresa L.; Metcalfe, Maureen G.; Humphrey, Charles D.; Hill, Vincent R.

2016-01-01

It is generally accepted that viral particles in source water are likely to be found as aggregates attached to other particles. For this reason, it is important to investigate the disinfection efficacy of chlorine on aggregated viruses. A method to produce adenovirus particle aggregation was developed for this study. Negative stain electron microscopy was used to measure aggregation before and after addition of virus particles to surface water at different pH and specific conductance levels. The impact of aggregation on the efficacy of chlorine disinfection was also examined. Disinfection experiments with human adenovirus 2 (HAdV2) in source water were conducted using 0.2 mg/L free chlorine at 5 °C. Aggregation of HAdV2 in source water (≥3 aggregated particles) remained higher at higher specific conductance and pH levels. However, aggregation was highly variable, with the percentage of particles present in aggregates ranging from 43 to 71 %. Upon addition into source water, the aggregation percentage dropped dramatically. On average, chlorination CT values (chlorine concentration in mg/L × time in min) for 3-log10 inactivation of aggregated HAdV2 were up to three times higher than those for dispersed HAdV2, indicating that aggregation reduced the disinfection rate. This information can be used by water utilities and regulators to guide decision making regarding disinfection of viruses in water. PMID:26910058

Aggregation of Adenovirus 2 in Source Water and Impacts on Disinfection by Chlorine.

PubMed

Kahler, Amy M; Cromeans, Theresa L; Metcalfe, Maureen G; Humphrey, Charles D; Hill, Vincent R

2016-06-01

It is generally accepted that viral particles in source water are likely to be found as aggregates attached to other particles. For this reason, it is important to investigate the disinfection efficacy of chlorine on aggregated viruses. A method to produce adenovirus particle aggregation was developed for this study. Negative stain electron microscopy was used to measure aggregation before and after addition of virus particles to surface water at different pH and specific conductance levels. The impact of aggregation on the efficacy of chlorine disinfection was also examined. Disinfection experiments with human adenovirus 2 (HAdV2) in source water were conducted using 0.2 mg/L free chlorine at 5 °C. Aggregation of HAdV2 in source water (≥3 aggregated particles) remained higher at higher specific conductance and pH levels. However, aggregation was highly variable, with the percentage of particles present in aggregates ranging from 43 to 71 %. Upon addition into source water, the aggregation percentage dropped dramatically. On average, chlorination CT values (chlorine concentration in mg/L × time in min) for 3-log10 inactivation of aggregated HAdV2 were up to three times higher than those for dispersed HAdV2, indicating that aggregation reduced the disinfection rate. This information can be used by water utilities and regulators to guide decision making regarding disinfection of viruses in water.

Chemical and biological quality of selected lakes in Ohio, 1976 and 1977

USGS Publications Warehouse

Tobin, Robert L.; Youger, John D.

1979-01-01

Twenty-eight Ohio lakes (14 per year) were sampled by the U.S. Geological Survey and Ohio Environmental Protection Agency for the water-quality characteristics during the spring and summer of 1976 and 1977. Data items included: profiles of temperature, dissolved oxygen, pH, and specific conductance; physical, biological, nutrient, and organic characteristics; major and minor constituents; and physical and chemical data associated with major inflows. Light penetration (secchi disk) was greatest (21 feet) in Mogadore Reservoir and least (0.8 foot) in Stonelick Lake. Seasonal thermal gradients developed in most lakes greater than 17 feet in depth. Dissolved-oxygen saturation ranged from 220 percent in Summit Lake to zero percent in the bottom waters of all lakes having stable thermal gradients. Five-day BOD ranged from 0.3 milligrams per liter im Michael J. Kirwan Reservoir to more than 17 milligrams per liter in Nimisilia Reservoir. Anaerobic zones were frequently characterized by hydrogen sulfide and high concentrations of ammonia. All lakes had moderately hard to very hard waters. Calcium, bicarbonate, and sulfate were the principal constituents. Specific conductance ranged from 130 micromhos (Lake Logan) to 1250 micromhos (Summit Lake). Because of nutrient uptake and recycling, significant chemical and physical differences developed in different thermal strata. Pesticide residues and trace elements were not above the limits recommended by the Ohio Environmental Protection Agency. All counts of fecal colifrom bacteria were within State standards. Blue-green algae (Cyanophyta) dominated the phytoplankton communities of 18 lakes in spring and 26 lakes in summer. Algal counts from euphotic-zone composite samples ranged from 180 cells per milliliter in Killdeer Reservoir to 3,400,000 cells per milliliter in Kiser Lake. Maximum algal counts were greater than 100,000 cells per milliliter in 19 lakes. Streams ate a major source of macronutrients in Ohio lakes. The estimated discharge-weighted mean concentration for nitrite and total phosphorus in 62 inflow samples was 1.22 milligrams per liter as N and 0.12 milligrams per liter as P.

An Integrated Lab-on-Chip for Rapid Identification and Simultaneous Differentiation of Tropical Pathogens

PubMed Central

Sato, Mitsuharu; Watthanaworawit, Wanitda; Ling, Clare L.; Mauduit, Marjorie; Malleret, Benoît; Grüner, Anne-Charlotte; Tan, Rosemary; Nosten, François H.; Snounou, Georges; Rénia, Laurent; Ng, Lisa F. P.

2014-01-01

Tropical pathogens often cause febrile illnesses in humans and are responsible for considerable morbidity and mortality. The similarities in clinical symptoms provoked by these pathogens make diagnosis difficult. Thus, early, rapid and accurate diagnosis will be crucial in patient management and in the control of these diseases. In this study, a microfluidic lab-on-chip integrating multiplex molecular amplification and DNA microarray hybridization was developed for simultaneous detection and species differentiation of 26 globally important tropical pathogens. The analytical performance of the lab-on-chip for each pathogen ranged from 102 to 103 DNA or RNA copies. Assay performance was further verified with human whole blood spiked with Plasmodium falciparum and Chikungunya virus that yielded a range of detection from 200 to 4×105 parasites, and from 250 to 4×107 PFU respectively. This lab-on-chip was subsequently assessed and evaluated using 170 retrospective patient specimens in Singapore and Thailand. The lab-on-chip had a detection sensitivity of 83.1% and a specificity of 100% for P. falciparum; a sensitivity of 91.3% and a specificity of 99.3% for P. vivax; a positive 90.0% agreement and a specificity of 100% for Chikungunya virus; and a positive 85.0% agreement and a specificity of 100% for Dengue virus serotype 3 with reference methods conducted on the samples. Results suggested the practicality of an amplification microarray-based approach in a field setting for high-throughput detection and identification of tropical pathogens. PMID:25078474

The effect of group-exercising on females with non-specific chronic low back pain in a sitting position: a pilot study.

PubMed

Beladev, Noa; Masharawi, Youssef

2011-01-01

The aim of this study was to investigate the effect of active group-exercising on women with non specific chronic low back pain (NSCLBP) in a sitting position. 25 females with NSCLBP underwent 8 group sitting-exercise sessions of a 45 minute duration, over an 8 week period. Pain intensity (VAS), back specific disability (Rolland Morris questionnaire-RMQ), and lumbar flexion and extension ranges of motion were measured twice, for reliability tests and cut-off score values, with a 1 week interval between measurements, prior to intervention and subsequently, six weeks following intervention. Several significant changes in outcome measures were indicated following intervention compared with baseline (p < 0.001): an increase in lumbar flexion and extension (mean differences of 6° for flexion and 4° for extension, cutoff score = 5.91°); reduction in VAS score (mean difference=4.21, cutoff score =4.48); an increase in RMQ total score (mean difference=10.76, cutoff score=8.15). Changes in the VAS score was highly correlated with changes in the RMQ score (r=- 6.35). A functional program of group-exercising conducted in a sitting position, improved the functional, painful status and lumbar ranges of motion in the sagittal plane of women suffering from non specific chronic low back pain. As sitting is considered the most common posture in today's workplace, applying this protocol during working hours would be very effective.

Measuring and modeling the variation in species-specific transpiration in temperate deciduous hardwoods.

PubMed

Bowden, Joseph D; Bauerle, William L

2008-11-01

We investigated which parameters required by the MAESTRA model were most important in predicting leaf-area-based transpiration in 5-year-old trees of five deciduous hardwood species-yoshino cherry (Prunus x yedoensis Matsum.), red maple (Acer rubrum L. 'Autumn Flame'), trident maple (Acer buergeranum Miq.), Japanese flowering cherry (Prunus serrulata Lindl. 'Kwanzan') and London plane-tree (Platanus x acerifolia (Ait.) Willd.). Transpiration estimated from sap flow measured by the heat balance method in branches and trunks was compared with estimates predicted by the three-dimensional transpiration, photosynthesis and absorbed radiation model, MAESTRA. MAESTRA predicted species-specific transpiration from the interactions of leaf-level physiology and spatially explicit micro-scale weather patterns in a mixed deciduous hardwood plantation on a 15-min time step. The monthly differences between modeled mean daily transpiration estimates and measured mean daily sap flow ranged from a 35% underestimation for Acer buergeranum in June to a 25% overestimation for A. rubrum in July. The sensitivity of the modeled transpiration estimates was examined across a 30% error range for seven physiological input parameters. The minimum value of stomatal conductance as incident solar radiation tends to zero was determined to be eight times more influential than all other physiological model input parameters. This work quantified the major factors that influence modeled species-specific transpiration and confirmed the ability to scale leaf-level physiological attributes to whole-crown transpiration on a species-specific basis.

Geophysical detection of on-site wastewater plumes in the North Carolina Coastal Plain, USA

NASA Astrophysics Data System (ADS)

Smith, Matthew

Nonpoint source pollution (NPS) continues to be the leading cause of water quality degradation in the United States. On-site wastewater systems (OWS) contribute to NPS; however, due to the range of system designs and complexity of the subsurface, OWS contributions to groundwater pollution are not well understood. As the population of coastal North Carolina continues to increase, better methods to locate and characterize wastewater impacted groundwater are needed. Previous studies have demonstrated the ability of non-intrusive geophysical methods to provide high resolution information on various contaminants in different geologic settings. The goals of this study were to evaluate the utility of ground penetrating radar (GPR) and capacitively coupled resistivity (CCR) for detecting OWS components, delineating associated wastewater plumes, and monitoring temporal variations in groundwater quality. Cross-sectional and three dimensional (3D) geophysical surveys were conducted periodically over a one year period (February 2011--January 2012) at two schools utilizing OWS in the lower Neuse River Basin (NRB) in the North Carolina Coastal Plain (NCCP). Cores were collected at both study sites; as well as monthly groundwater depth, temperature, and specific conductivity measurements to better constrain the geophysical interpretations. Additionally, dissolved inorganic nitrogen (DIN) and Cl concentrations were monitored bi-monthly to assess nutrient transport at the sites. The 3D GPR surveys effectively located the wastewater drainage trenches at both sites, in close agreement with locations described in as-built OWS blueprints. Regression analysis of resistivity versus groundwater specific conductivity revealed an inverse relationship, suggesting resistivity ≤ 250 ohm.m was indicative of wastewater impacted groundwater at both sites. The 3D resistivity models identified regions of low resistivity beneath the drainfields relative to background values. Regression analysis of GPR signal absolute peak amplitude (APA) versus groundwater specific conductivity revealed a decrease in APA indicative of radar signal attenuation at locations where groundwater specific conductivity was elevated. The 3D GPR models identified regions of attenuated radar signal beneath the drainfields relative to background locations. Comparisons of groundwater specific conductivity, GPR, and CCR lateral wastewater plume estimates indicated similar dimensions at both sites. The sensitivity of resistivity measurements tended to decline with increased water-table depth; although, differences in resistivity associated with seasonal water-table depth changes were noticeable. Overall, results of this study suggest that GPR and CCR surveys combined with sediment, hydrologic, and water quality data may provide reliable information on the location of OWS components and extent of associated wastewater plumes. The GPR surveys successfully located the wastewater drainage trenches and helped image the uppermost surface of the wastewater plumes. The CCR surveys delineated the lateral wastewater plume dimensions and revealed temporal changes in groundwater quality associated with differences in groundwater recharge.

Safety Communication Tools and Healthcare Professionals' Awareness of Specific Drug Safety Issues in Europe: A Survey Study.

PubMed

de Vries, Sieta T; van der Sar, Maartje J M; Coleman, Anna Marie; Escudero, Yvette; Rodríguez Pascual, Alfonso; Maciá Martínez, Miguel-Ángel; Cupelli, Amelia; Baldelli, Ilaria; Šipić, Ivana; Andrić, Adriana; Michan, Line; Denig, Petra; Mol, Peter G M

2018-07-01

National competent authorities (NCAs) use Direct Healthcare Professional Communications (DHPCs) to communicate new drug safety issues to healthcare professionals (HCPs). More knowledge is needed about the effectiveness of DHPCs and the extent to which they raise awareness of new safety issues among HCPs. The objective was to assess and compare general practitioners' (GPs'), cardiologists', and pharmacists' familiarity with DHPCs as communication tools, their awareness of specific drug safety issues, and the sources through which they had become aware of the specific issues. GPs, cardiologists, and pharmacists from nine European countries (Croatia, Denmark, Ireland, Italy, the Netherlands, Norway, Spain, Sweden, and the UK) completed a web-based survey. The survey was conducted in the context of the Strengthening Collaboration for Operating Pharmacovigilance in Europe (SCOPE) Joint Action. Respondents were asked about their familiarity with DHPCs in general and their awareness of safety issues that had recently been communicated and involved the following drugs: combined hormonal contraceptives, diclofenac, valproate, and ivabradine. Those HCPs who were aware of the specific safety issues were subsequently asked to indicate the source through which they had become aware of them. Differences between professions in familiarity with DHPCs and awareness were tested using a Pearson χ 2  test per country and post hoc Pearson χ 2  tests in the case of statistically significant differences. Of the 3288 included respondents, 54% were GPs, 40% were pharmacists, and 7% were cardiologists. The number of respondents ranged from 67 in Denmark to 916 in Spain. Most respondents (92%) were familiar with DHPCs, with one significant difference between the professions: pharmacists were more familiar than GPs in Italy (99 vs 90%, P = 0.004). GPs' awareness ranged from 96% for the diclofenac issue to 70% for the ivabradine issue. A similar pattern was shown for pharmacists (91% aware of the diclofenac issue to 66% of the ivabradine issue). Cardiologists' awareness ranged from 91% for the ivabradine issue to 34% for the valproate issue. Overall, DHPCs were a common source through which GPs (range: 45% of those aware of the contraceptives issue to 60% of those aware of the valproate issue), cardiologists (range: 33% for the contraceptives issue to 61% for the valproate issue), and pharmacists (range: 41% for the contraceptives issue to 51% for the ivabradine issue) had become aware of the specific safety issues, followed by information on websites or in newsletters. GPs, cardiologists, and pharmacists were to a similar extent (highly) familiar with DHPCs, but they differed in awareness levels of specific safety issues. Cardiologists were less aware of safety issues associated with non-cardiology drugs even if these had cardiovascular safety concerns. This implies that additional strategies may be needed to reach specialists when communicating safety issues regarding drugs outside their therapeutic area but with risks related to their field of specialisation. DHPCs were an important source for the different professions to become aware of specific safety issues, but other sources were also often used. NCAs should consider the use of a range of sources when communicating important safety issues to HCPs.

Crowdsourcing as a screening tool to detect clinical features of glaucomatous optic neuropathy from digital photography.

PubMed

Mitry, Danny; Peto, Tunde; Hayat, Shabina; Blows, Peter; Morgan, James; Khaw, Kay-Tee; Foster, Paul J

2015-01-01

Crowdsourcing is the process of simplifying and outsourcing numerous tasks to many untrained individuals. Our aim was to assess the performance and repeatability of crowdsourcing in the classification of normal and glaucomatous discs from optic disc images. Optic disc images (N = 127) with pre-determined disease status were selected by consensus agreement from grading experts from a large cohort study. After reading brief illustrative instructions, we requested that knowledge workers (KWs) from a crowdsourcing platform (Amazon MTurk) classified each image as normal or abnormal. Each image was classified 20 times by different KWs. Two study designs were examined to assess the effect of varying KW experience and both study designs were conducted twice for consistency. Performance was assessed by comparing the sensitivity, specificity and area under the receiver operating characteristic curve (AUC). Overall, 2,540 classifications were received in under 24 hours at minimal cost. The sensitivity ranged between 83-88% across both trials and study designs, however the specificity was poor, ranging between 35-43%. In trial 1, the highest AUC (95%CI) was 0.64(0.62-0.66) and in trial 2 it was 0.63(0.61-0.65). There were no significant differences between study design or trials conducted. Crowdsourcing represents a cost-effective method of image analysis which demonstrates good repeatability and a high sensitivity. Optimisation of variables such as reward schemes, mode of image presentation, expanded response options and incorporation of training modules should be examined to determine their effect on the accuracy and reliability of this technique in retinal image analysis.

Evaluation of borehole geophysical logging, aquifer-isolation tests, distribution of contaminants, and water-level measurements at the North Penn Area 5 Superfund Site, Bucks and Montgomery counties, Pennsylvania

USGS Publications Warehouse

Bird, Philip H.; Conger, Randall W.

2002-01-01

Borehole geophysical logging and aquifer-isolation (packer) tests were conducted at the North Penn Area 5 Superfund site in Bucks and Montgomery Counties, Pa. Caliper, naturalgamma, single-point-resistance, fluid-temperature, fluid-resistivity, heatpulse-flowmeter, and digital acoustic-televiewer logs and borehole television surveys were collected in 32 new and previously drilled wells that ranged in depth from 68 to 302 feet. Vertical borehole-fluid movement direction and rate were measured with a high-resolution heatpulse flowmeter under nonpumping conditions. The suite of logs was used to locate water-bearing fractures, determine zones of vertical borehole-fluid movement, select depths to set packers, and locate appropriate screen intervals for reconstructing new wells as monitoring wells. Aquifer-isolation tests were conducted in four wells to sample discrete intervals and to determine specific capacities of discrete water-bearing zones. Specific capacities of isolated zones during packer testing ranged from 0.12 to 15.30 gallons per minute per foot. Most fractures identified by borehole geophysical methods as water-producing or water-receiving zones produced water when isolated and pumped. The acoustic-televiewer logs define two basic fracture sets, bedding-plane partings with a mean strike of N. 62° E. and a mean dip of 27° NW., and high-angle fractures with a mean strike of N. 58° E. and a mean dip of 72° SE. Correlation of heatpulse-flowmeter data and acoustic-televiewer logs showed 83 percent of identified water-bearing fractures were high-angle fractures.

Material from the Internal Surface of Squid Axon Exhibits Excess Noise

PubMed Central

Fishman, Harvey M.

1981-01-01

A fluid material from a squid (Loligo pealei) axon was isolated by mechanical application of two types of microcapillary (1-3-μm Diam) to the internal surface of intact and cut-axon preparations. Current noise in the isolated material exceeded thermal levels and power spectra were 1/f in form in the frequency range 1.25-500 Hz with voltage-dependent intensities that were unrelated to specific ion channels. Whether conduction in this material is a significant source of excess noise during axon conduction remains to be determined. Nevertheless, a source of excess noise external to or within an ion channel may not be properly represented solely as an additive term to the spectrum of ion channel noise; a deconvolution of these spectral components may be required for modeling purposes. PMID:6266542

Pulsed plasmoid electric propulsion

NASA Technical Reports Server (NTRS)

Bourque, Robert F.; Parks, Paul B.; Tamano, Teruo

1990-01-01

A method of electric propulsion is explored where plasmoids such as spheromaks and field reversed configurations (FRC) are formed and then allowed to expand down a diverging conducting shell. The plasmoids contain a toroidal electric current that provides both heating and a confining magnetic field. They are free to translate because there are no externally supplied magnetic fields that would restrict motion. Image currents in the diverging conducting shell keep the plasmoids from contacting the wall. Because these currents translate relative to the wall, losses due to magnetic flux diffusion into the wall are minimized. During the expansion of the plasma in the diverging cone, both the inductive and thermal plasma energy are converted to directed kinetic energy producing thrust. Specific impulses can be in the 4000 to 20000 sec range with thrusts from 0.1 to 1000 Newtons, depending on available power.

Groundwater monitoring of hydraulic fracturing in California: Recommendations for permit-required monitoring

NASA Astrophysics Data System (ADS)

Esser, B. K.; Beller, H. R.; Carroll, S.; Cherry, J. A.; Jackson, R. B.; Jordan, P. D.; Madrid, V.; Morris, J.; Parker, B. L.; Stringfellow, W. T.; Varadharajan, C.; Vengosh, A.

2015-12-01

California recently passed legislation mandating dedicated groundwater quality monitoring for new well stimulation operations. The authors provided the State with expert advice on the design of such monitoring networks. Factors that must be considered in designing a new and unique groundwater monitoring program include: Program design: The design of a monitoring program is contingent on its purpose, which can range from detection of individual well leakage to demonstration of regional impact. The regulatory goals for permit-required monitoring conducted by operators on a well-by-well basis will differ from the scientific goals of a regional monitoring program conducted by the State. Vulnerability assessment: Identifying factors that increase the probability of transport of fluids from the hydrocarbon target zone to a protected groundwater zone enables the intensity of permit-required monitoring to be tiered by risk and also enables prioritization of regional monitoring of groundwater basins based on vulnerability. Risk factors include well integrity; proximity to existing wellbores and geologic features; wastewater disposal; vertical separation between the hydrocarbon and groundwater zones; and site-specific hydrogeology. Analyte choice: The choice of chemical analytes in a regulatory monitoring program is guided by the goals of detecting impact, assuring public safety, preventing resource degradation, and minimizing cost. Balancing these goals may be best served by tiered approach in which targeted analysis of specific chemical additives is triggered by significant changes in relevant but more easily analyzed constituents. Such an approach requires characterization of baseline conditions, especially in areas with long histories of oil and gas development. Monitoring technology: Monitoring a deep subsurface process or a long wellbore is more challenging than monitoring a surface industrial source. The requirement for monitoring multiple groundwater aquifers across a range of depths and of monitoring at deeper depths than is typical for regulatory monitoring programs requires consideration of monitoring technology, which can range from clusters of wells to multiple wells in a single wellbore to multi-level systems in a single cased wellbore.

Evaluation of acoustic Doppler velocimetry (ADV) performance under various probe configurations

NASA Astrophysics Data System (ADS)

Liu, Da; Valyrakis, Manousos

2017-04-01

Acoustic Doppler velocimetry (ADV) is widely used as one of the most versatile and robust flow diagnostics tools for both laboratory and field studies across a range of research and applied themes spanning engineering eco-hydraulics and geomorphology. A range of specific ADV probes with varying specifications, are readily available for use by professionals and researchers. However, in practice using certain ADV equipment under certain default configurations can easily result in obtaining flow diagnostics that are non-representative of the real flow conditions. This appears to be true for most probes but even more those with which higher temporal resolution can be achieved - which many times is desired for assessing turbulence levels, amongst others. A preliminary examination revealed that there is a varying level of dependency on a number of the probes' configuration parameters, which even though detailed in the user manual, a definite guide for the user is lacking. Subsequently users of this equipment may end up underutilizing or using it in a manner that returns inaccurate results. There are little, if any, resources in obtaining a better understanding on how to use the probe effectively. To this goal a series of laboratory experiments are conducted, under the same open channel flow conditions, using a profiler (ADCP VectrinoII from Nortek®) aiming to cover the full range of probe configuration combinations that can be used in practice. For each experiment, single or multiple point measurements are taken to reconstruct velocity and turbulence intensity profiles. These are conducted at the same location (mid-channel) under the same flow conditions (referring to steady uniform flow and fully developed turbulence) for all probe configurations. In particular, the effect of tested parameters (including Range length, Range to fist cell, Sampling rate, Ping algorithm, Transmit pulse size and Cell size) on the sensitivity and accuracy of the obtained results is assessed. The signal to noise ratio (SNR) and the correlation of the measurement are used in evaluating the data quality, while a qualitative comparison of the resulting profiles for flow diagnostics is enabled using reference profiles obtained via a VectrinoI ADV (from Nortek®) and MicroADV (from Sontek®) respectively under the exactly same flow condition at the same location. These observations are important to identify its best configuration for a given probe towards improving the data quality and accuracy.

Analysis of pumping tests: Significance of well diameter, partial penetration, and noise

USGS Publications Warehouse

Heidari, M.; Ghiassi, K.; Mehnert, E.

1999-01-01

The nonlinear least squares (NLS) method was applied to pumping and recovery aquifer test data in confined and unconfined aquifers with finite diameter and partially penetrating pumping wells, and with partially penetrating piezometers or observation wells. It was demonstrated that noiseless and moderately noisy drawdown data from observation points located less than two saturated thicknesses of the aquifer from the pumping well produced an exact or acceptable set of parameters when the diameter of the pumping well was included in the analysis. The accuracy of the estimated parameters, particularly that of specific storage, decreased with increases in the noise level in the observed drawdown data. With consideration of the well radii, the noiseless drawdown data from the pumping well in an unconfined aquifer produced good estimates of horizontal and vertical hydraulic conductivities and specific yield, but the estimated specific storage was unacceptable. When noisy data from the pumping well were used, an acceptable set of parameters was not obtained. Further experiments with noisy drawdown data in an unconfined aquifer revealed that when the well diameter was included in the analysis, hydraulic conductivity, specific yield and vertical hydraulic conductivity may be estimated rather effectively from piezometers located over a range of distances from the pumping well. Estimation of specific storage became less reliable for piezemeters located at distances greater than the initial saturated thickness of the aquifer. Application of the NLS to field pumping and recovery data from a confined aquifer showed that the estimated parameters from the two tests were in good agreement only when the well diameter was included in the analysis. Without consideration of well radii, the estimated values of hydraulic conductivity from the pumping and recovery tests were off by a factor of four.The nonlinear least squares method was applied to pumping and recovery aquifer test data in confined and unconfined aquifers with finite diameter and partially penetrating piezometers and observation wells. Noiseless and moderately noisy drawdown data from observation points located less than two saturated thicknesses of the aquifer from the pumping well produced a set of parameters that agrees very well with piezometer test data when the diameter of the pumping well was included in the analysis. The accuracy of the estimated parameters decreased with increasing noise level.

Associations between benthic flora and diel changes in dissolved arsenic, phosphorus, and related physico-chemical parameters

USGS Publications Warehouse

Kuwabara, James S.

1992-01-01

Diel relationships between physical and chemical parameters and biomass were examined along a 57-km reach of Whitewood Creek, South Dakota, between 29 August and 2 September 1988. A time lag of ∼3-6 h for fluctuations in soluble reactive phosphorus (SRP) concentrations (ranging from 0.1 to 0.5 μM at the downstream sites) relative to dissolved arsenic (ranging from 0.3 to 1.2 μM as arsenate (pentavalent arsenic)) was consistent with our laboratory studies (reported elsewhere) showing preferential cell sorption of orthophosphate over arsenate by creek periphyton. The potential biological effects on SRP diel fluctuations contrasts with abiotic sorption controls for dissolved arsenate (a chemically similar anion). Cycles for pH, like water temperature cycles, lagged irradiance cycles by 1-3 h. Like pH, the amplitude of dissolved arsenic diel cycles was greatest at the site with most abundant biomass. Diel fluctuations in specific conductance (an indicator of groundwater inputs at elevated conductivity relative to the water column) were out of phase with both SRP and dissolved arsenic concentrations suggesting that groundwater was not the direct source of these solutes.

Facile synthesis of Li2S-P2S5 glass-ceramics electrolyte with micron range particles for all-solid-state batteries via a low-temperature solution technique (LTST)

NASA Astrophysics Data System (ADS)

Choi, Sunho; Lee, Sewook; Park, Jongyeop; Nichols, William T.; Shin, Dongwook

2018-06-01

A lithium ion conductive 75Li2Sṡ25P2S5 glass-ceramics electrolyte is, for the first time, successfully synthesized via a new low-temperature solution technique (LTST) and compared to the conventional mechanical-milling technique. Both samples are composed of the highly lithium ion conductive thio-LISICON III analog phase. Due to the uniform dispersion of reactants in an organic liquid, the use of LTST produced significantly smaller and more uniform particle sizes (2.2 ± 1.68 μm) resulting in a 6.5 times higher specific surface area compared to the mechanically-milled sample. A pronounced enhancement of both the rate capability and cyclability is demonstrated for the LTST solid electrolyte sample due to the more intimate contact with the LiCoO2 active material. Furthermore, the LTST sample shows excellent electrochemical stability throughout the potential range of -1 to 5 V. These results suggest that the proposed technique using the optimized LTST process is promising for the preparation of 75Li2Sṡ25P2S5 solid electrolytes for use in advanced Li-ion batteries.

Preventing risky behaviours among young adolescents in eastern Democratic Republic of Congo: A qualitative study.

PubMed

Kohli, Anjalee; Remy, Mitima Mpanano; Binkurhorhwa, Arsene Kajabika; Mitima, Clovis Murhula; Mirindi, Alfred Bacikenge; Mwinja, Nadine Bufole; Banyewesize, Jean Heri; Ntakwinja, Gisele Mushengezi; Perrin, Nancy A; Glass, Nancy

2017-04-26

This qualitative study explores and describes adolescent risk behaviours, specifically consumption of alcohol and use of violence; the perceived consequences of these behaviours on future well-being and relationships; and collaboratively identifies the essential components of a prevention intervention for risk behaviours (alcohol use, violence) among young adolescents while strengthening the protective individual and relationship factors in post-conflict Democratic Republic of Congo. One-on-one in-depth interviews were conducted with 28 male and female youth, 20 parents/guardians and 20 stakeholders in three rural villages of South Kivu Province. Trained interviewers conducted interviews and participated in daily debriefing. Descriptive qualitative analysis was used to analyse the data. Youth use of violence and alcohol was associated with a range of factors including peer influence, parent behaviours, school enrolment and poverty. The consequences of risk behaviour include damaged family and social bonds, reduced economic and educational productivity and promise. Community-based, multilevel prevention interventions that promote protective factors and reduce youth exposure and vulnerability to risk factors may have immediate and long-term impact on youth health and behaviour. Such a programme could engage youth, adults and local stakeholders in a range of social, educational and economic activities.

Optical and Nanoparticle Analysis of Normal and Cancer Cells by Light Transmission Spectroscopy

NASA Astrophysics Data System (ADS)

Deatsch, Alison; Sun, Nan; Johnson, Jeffery; Stack, Sharon; Szajko, John; Sander, Christopher; Rebuyon, Roland; Easton, Judah; Tanner, Carol; Ruggiero, Steven

2015-03-01

We have investigated the optical properties of human oral and ovarian cancer and normal cells. Specifically, we have measured the absolute optical extinction for intra-cellular material (lysates) in aqueous suspension. Measurements were conducted over a wavelength range of 250 to 1000 nm with 1 nm resolution using Light Transmission Spectroscopy (LTS). This provides both the absolute extinction of materials under study and, with Mie inversion, the absolute number of particles of a given diameter as a function of diameter in the range of 1 to 3000 nm. Our preliminary studies show significant differences in both the extinction and particle size distributions associated with cancer versus normal cells, which appear to be correlated with differences in the particle size distribution in the range of approximately 50 to 250 nm. Especially significant is a clearly higher density of particles at about 100 nm and smaller for normal cells. Department of Physics, Harper Cancer Research Institute, and the Office of Research at the University of Notre Dame.

Petroleum pollution in mangrove forests sediments from Qeshm Island and Khamir Port-Persian Gulf, Iran.

PubMed

Ebrahimi-Sirizi, Zohreh; Riyahi-Bakhtiyari, Alireza

2013-05-01

The concentrations of total polycyclic aromatic hydrocarbons (PAHs) and 22 individual PAH compounds in 42 surface sediments collected from the mangrove forest of Qeshm Island and Khamir Port (Persian Gulf) were analyzed. PAHs concentrations ranged from 259 to 5,376 ng g(-1) dry weight with mean and median values of 1,585 and 1,146 ng g(-1), respectively. The mangrove sediments had higher percentages of lower molecular weight PAHs and the PAH profiles were dominated by naphthalene. Ratio values of specific PAH compounds were calculated to evaluate the possible source of PAH contamination. This ratios suggesting that the mangrove sediments have a petrogenic input of PAHs. Sediment quality guidelines were conducted to assess the toxicity of PAH compounds. The levels of total PAHs at all of stations except one station, namely Q6, were below the effects range low. Also, concentrations of naphthalene in some stations exceeded the effects range median.

Estimation of Phonon and Carrier Thermal Conductivities for Bulk Thermoelectric Materials Using Transport Properties

NASA Astrophysics Data System (ADS)

Otsuka, Mioko; Homma, Ryoei; Hasegawa, Yasuhiro

2017-05-01

The phonon and carrier thermal conductivities of thermoelectric materials were calculated using the Wiedemann-Franz law, Boltzmann equation, and a method we propose in this study called the Debye specific heat method. We prepared polycrystalline n-type doped bismuth telluride (BiTe) and bismuth antimony (BiSb) bulk alloy samples and measured six parameters (Seebeck coefficient, resistivity, thermal conductivity, thermal diffusivity, magneto-resistivity, and Hall coefficient). The carrier density and mobility were estimated for calculating the carrier thermal conductivity by using the Boltzmann equation. In the Debye specific heat method, the phonon thermal diffusivity, and thermal conductivity were calculated from the temperature dependence of the effective specific heat by using not only the measured thermal conductivity and Debye model, but also the measured thermal diffusivity. The carrier thermal conductivity was also evaluated from the phonon thermal conductivity by using the specific heat. The ratio of carrier thermal conductivity to thermal conductivity was evaluated for the BiTe and BiSb samples, and the values obtained using the Debye specific heat method at 300 K were 52% for BiTe and <5.5% for BiSb. These values are either considerably larger or smaller than those obtained using other methods. The Dulong-Petit law was applied to validate the Debye specific heat method at 300 K, which is significantly greater than the Debye temperature of the BiTe and BiSb samples, and it was confirmed that the phonon specific heat at 300 K has been accurately reproduced using our proposed method.

Below- and above-ground controls on tree water use in lowland tropical forests

NASA Astrophysics Data System (ADS)

Meinzer, F. C.; Woodruff, D.; McCulloh, K.; Domec, J.

2012-12-01

Even in moist tropical forests, fluctuations in soil water availability and atmospheric evaporative demand can constrain tree water use. Our research in three lowland tropical forest sites in Panama over the past two decades has identified a series of tree biophysical and functional traits related to daily and seasonal patterns of uptake, transport and loss of water. Studies combining measurements of sap flow and natural abundance of hydrogen isotopes in soil and xylem water during the dry season show considerable variation in depth of soil water uptake among co-occurring species. Trees able to exploit progressively deeper sources of soil water during the dry season, as indicated by increasingly negative xylem water hydrogen isotope ratios, were also able to maintain constant or even increased rates of water use. Injections of a stable isotope tracer (deuterated water) into tree trunks revealed a considerable range of water transit and residence times among co-occurring, similarly-sized trees. Components of tree hydraulic architecture were also strong determinants of patterns of water use. Sapwood hydraulic capacitance, the amount of water released per unit change in tissue water potential, was a strong predictor of several tree water use and water relations traits, including sap velocity, water residence time, daily maximum branch xylem tension, and the time of day at which stomata began to increasingly restrict transpiration. Among early and late successional species, hydraulic traits such as trunk-to-branch tapering of xylem vessels, branch sap flux, branch sapwood specific conductivity and whole-tree leaf area-specific hydraulic conductance scaled uniformly with branch wood density. Consistent with differences in trunk-to-branch tapering of vessels between early and late successional species, the ratio of branch to trunk sap flux was substantially greater in early successional species. Among species, stomatal conductance and transpiration per unit leaf area scaled uniformly with branch leaf-specific conductivity and with the branch leaf area to sapwood area ratio; a tree architecture-based proxy for leaf-specific conductivity. At the canopy-atmosphere interface, a combination of high stomatal conductance and relatively large leaf size enhanced the role of the boundary layer over stomata in controlling transpiration (increased decoupling coefficient; omega). Uniform scaling of tree water use characteristics with simple biophysical, hydraulic and architectural traits across species may facilitate predictions of changes in tropical forest water use with shifts in species composition associated with climate change and changing land-use.

Probability analysis of the relation of salinity to freshwater discharge in the St. Sebastian River, Florida

USGS Publications Warehouse

Wicklein, S.M.; Gain, W.S.

1999-01-01

The St. Sebastian River lies in the southern part of the Indian River basin on the east coast of Florida. Increases in freshwater discharge due to urbanization and changes in land use have reduced salinity in the St. Sebastian River and, consequently, salinity in the Indian River, affecting the commercial fishing industry. Wind, water temperature, tidal flux, freshwater discharge, and downstream salinity all affect salinity in the St. Sebastian River estuary, but freshwater discharge is the only one of these hydrologic factors which might be affected by water-management practices. A probability analysis of salinity conditions in the St. Sebastian River estuary, taking into account the effects of freshwater discharge over a period from May 1992 to March 1996, was used to determine the likelihood (probability) that salinities, as represented by daily mean specific- conductance values, will fall below a given threshold. The effects of freshwater discharge on salinities were evaluated with a simple volumetric model fitted to time series of measured specific conductance, by using nonlinear optimization techniques. Specific-conductance values for two depths at monitored sites represent stratified flow which results from differences in salt concentration between freshwater and saltwater. Layering of freshwater and saltwater is assumed, and the model is applied independently to each layer with the assumption that the water within the layer is well mixed. The model of specific conductance as a function of discharge (a salinity response model) was combined with a model of residual variation to produce a total probability model. Flow distributions and model residuals were integrated to produce a salinity distribution and determine differences in salinity probabilities as a result of changes in water-management practices. Two possible management alternatives were analyzed: stormwater detention (reducing the peak rate of discharge but not reducing the overall flow volume) and stormwater retention (reducing peak discharges without later release). Detention of freshwater discharges increased the probability of specific- conductance values falling below a given limit (20,000 microsiemens per centimeter) for all sites but one. The retention of freshwater input to the system decreased the likelihood of falling below a selected limit of specific conductance at all sites. For limits of specific conductance (1,000 microsiemens per centimeter or 20,000 microsiemens per centimeter, depending on the site), the predicted days of occurrence below a limit decreased ranging from 17 to 68 percent of the predicted days of occurrence for unregulated flow. The primary finding to be drawn from the discharge-salinity analysis is that an empirical-response model alone does not provide adequate information to assess the response of the system to changes in flow regime. Whether a given level of discharge can produce a given response on a given day is not as important as the probability of that response on a given day and over a period of many days. A deterministic model of the St. Sebastian River estuary based only on discharge would predict that retention of discharge peaks should increase the average salinity conditions in the St. Sebastian River estuary. The probabilistic model produces a very different response indicating that salinity can decrease by a power of three as discharges increase, and that random factors can predominate and control salinity until discharges increase sufficiently to flush the entire system of saltwater.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mathee, Angela

Introduction: Lead exposure in shooting ranges has been under scrutiny for decades, but no information in this regard is available in respect of African settings, and in South Africa specifically. The aim of this study was to determine the blood lead levels in the users of randomly selected private shooting ranges in South Africa's Gauteng province. Methods: An analytical cross sectional study was conducted, with participants recruited from four randomly selected shooting ranges and three archery ranges as a comparator group. Results: A total of 118 (87 shooters and 31 archers) were included in the analysis. Shooters had significantly highermore » blood lead levels (BLL) compared to archers with 36/85 (42.4%) of shooters versus 2/34 (5.9%) of archers found to have a BLL ≥10 μg/dl (p<0.001). Conclusion: Shooting ranges may constitute an import site of elevated exposure to lead. Improved ventilation, low levels of awareness of lead hazards, poor housekeeping, and inadequate personal hygiene facilities and practices at South African shooting ranges need urgent attention. - Highlights: • This is the first study, to our knowledge, of lead exposure in shooting ranges in an African setting. • This study indicates highly elevated lead exposure amongst the users of certain private shooting ranges in South Africa. • Lead exposure may be a serious, yet under-studied, source of adult lead exposure in South Africa, and possibly elsewhere on the African continent.« less

Geohydrology and water quality of the unconsolidated deposits in Erie County, Pennsylvania

USGS Publications Warehouse

Buckwalter, T.F.; Schreffler, C.L.; Gleichsner, R.E.

1996-01-01

Water in unconsolidated deposits is used for the water supplies of homes, farms, municipalities, and industries in Erie County. The unconsolidated deposits cover most of the bedrock of Erie County. Thickness of the unconsolidated deposits ranged from 60 to 400 feet at 30 sites surveyed by seismic refraction and reflection methods. Water wells, mostly in the unconsolidated deposits, provide adequate domestic supplies. Wells in fractured bedrock can generally provide small domestic supplies; however, droughts can affect some of the domestic water wells. Ground-water withdrawals accounted for 10 million gallons per day of the water used in Erie County in 1984. Mean annual precipitation ranged from 42 to 47 inches per year in Erie County from 1961 through 1990; the southeastern region of the county generally receives more precipitation than the lake shore region to the north. Overland runoff to three segments of the French Creek watershed in the upland area ranged from about 13 to 19 in. per year and base flow ranged from 14 to about 18 in. per year from 1975 to 1992. Evapotranspiration ranged from about 13 to 16 in. per year for those segments. Beach and outwash deposits generally provide the largest supplies of water to wells in Erie County. A median specific capacity of 17 (gal/min)/ft (gallons per minute per foot) of drawdown was determined from records of nondomestic wells in beach deposits and 9 (gal/min)/ft of drawdown in outwash. Mean specific capacity for wells in till deposits was 1.5 (gal/min)/ft. The range in yield and specific capacity, however, was great for the unconsolidated deposits and high yielding outwash deposits are sometimes difficult to locate beneath till and valley-fill deposits. Hydraulic conductivities from three aquifer tests of outwash deposits (sand and gravel) at separate sites ranged from 110 to 2,030 ft/d (feet per day). Hydraulic conductivities from another aquifer test of sand and silt in the water table at Presque Isle ranged from 120 to 215 ft/d. Transmissivities from a third aquifer test of beach sand and gravel ranged from 235 to 262 feet squared per day. Laboratory analyses of stream samples collected during base flows in 1987 and 1988 indicate that concentrations of arsenic, barium, cadmium, chromium, fluoride, lead, mercury, and selenium did not exceed the maximum contaminant levels (MCL's) established for drinking water by the U.S. Environmental Protection Agency (USEPA). Concentrations of two nontoxic elements, iron and manganese, exceeded USEPA secondary maximum contaminant levels (SMCL's) in samples from selected stream sites. Manganese concentrations exceeded the SMCL of 0.05 milligrams per liter at 19 of 30 stream sites sampled in the Upland Plateau Section of Erie County. Twenty-one wells were sampled for inorganic constituents and selected pesticides. Some samples from three of the wells exceeded the MCL for nitrate. Total arsenic concentrations above the MCL of 50 micrograms per liter were documented intermittently in three water wells in North East Township. Water from six of seven tile drains sampled in agricultural fields contained detectable concentrations of herbicides. These samples document the transport of the herbicides from the shallow ground-water system to local streams. Herbicide concentrations were at or more than minimum reporting levels for atrazine, cyanazine, prometone, and simazine. Atrazine concentrations in all seven samples from tile drains did not exceed the USEPA MCL of 3.0 micrograms per liter.

Selected data on characteristics of glacial-deposit and carbonate-rock aquifers, midwestern basins and arches region

USGS Publications Warehouse

Joseph, R.L.; Eberts, S.M.

1994-01-01

In 1988, the Geological Survey (USGS) began study to examine the hydrogeologic framework, ground-water-flow systems, water chemistry, and withdrawal response of aquifers in glacial deposits and carbonate rock in the Midwestern Basins and Arches Region in western Ohio and eastern Indiana. As part of this study, data from pumped-well tests and instantaneous-rechange tests (slug tests) of wells completed in the glacial-deposit and carbonate-rock aquifers were compiled from reports and information on file with State agencies, environmental consulting firms, drilling firms, municipalities, universities, and the USGS. The data, from 73 counties in Ohio and Indiana, were entered into a computerized data base in a spreadsheet format and subsequently into a geographic information system (GIS). Aquifer-characteristics data from this compilation include the results of 105 pumped-well tests and 39 slug tests in wells completed in glacial deposits, 174 pumped-well tests in wells completed in the carbonate-rock aquifer, and 4 slug tests in wells completed in limestones and shales of Ordovician age. Transmissivities from the pumped-well tests in wells completed in glacial till and glacial-deposit aquifers (sands and gravels) range from 1.54 to 69,700 feet squared per day. Storage coefficients or specific yields range from 0.00002 to 0.38 at these wells. Horizontal-hydraulic conductivities from the slug tests in wells completed in glacial-deposit aquifers range from 0.33 to 1,000 feet per day. Transmissivities from the pumped-well tests in wells completed in the carbonate-rock aquifer range from 70 to 52,000 feet squared per day. Storage coefficient or specific yields at these wells range from 0.00001 to 0.05. Horizontal hydraulic conductivities from the slug tests in wells completed in limestones and shales of Ordovician age range from 0.0016 to 12 feet per day. These data are summarized in tables and figures within this report. The collection and compilation of selected aquifer-characteristic data for the glacial-deposit and carbonate-rock aquifers within the Midwestern Basin and Arches Region of Shaver (1985) are an essential part of the Midwestern Basins and Arches Regional Aquifer-Systems Analysis (Midwestern Basins and Arches RASA) project of the U.S. Geological Survey (USGS). Specifically, the data are needed to help describe ground-water flow in the regional aquifer system, which isone of the objectives of the Midwestern Basins and Arches RASA project (Bugliosi, 1990). To meet this objective, the Midwestern Basins and Arches RASA began subprojects in the Ohio and Indiana offices of the USGS to collect and compile available aquifer-characteristics data from aquifer tests of the glacial-deposit and carbonate-rock aquifers. The data were not reanalyzed to verify accuracy because of time constraints and insufficient data in many cases.

[Home range of Aspidoscelis cozumela (Squamata: Teiidae): a parthenogenetic lizard microendemic to Cozumel Island, México].

PubMed

Hernández-Gallegos, Oswaldo; López-Moreno, Ana Esthela; Méndez-Sánchez, José Fernando; Rheubert, Justin Lloyd; Méndez-de la Cruz, Fausto Roberto

2015-09-01

Home range is defined as the area within which an individual moves to acquire resources necessary to increase their fitness and may vary inter and intra-specifically with biotic and abiotic factors. This study details the home range of the parthenogenic lizard, Aspidoscelis cozumela, an active forager microendemic to Cozumel Island, México, with high preference for open sand beaches. The home range of A. cozumela was compared with other species of Aspidoscelis (gonochoric and parthenogenetic) and other lizards that occupy coastal habitats. Furthermore, the biotic and abiotic factors that may influence home range were analyzed. This study was conducted in the beach located on the East side of the island (area of 4,000 M2) that is composed primarily of halophyte vegetation with high levels of sunlight. From 1999 to 2001, nine samples were taken which included the dry, rainy, "nortes", and breeding seasons. During each sampling, capture-mark-recapture techniques were conducted and the date, time of day, and snout-vent length (SVL) were recorded to the nearest millimeter. Individuals were located in the study area using a bi-coordinate reference using 10 x 10 m subdivisions of the habitat. Home range and home range overlap were calculated using the convex polygon method in McPaal and home range/SVL correlation was tested using Pearson's correlation. To calculate females home range, three or more recaptures were considered. A total of 20 home ranges that averaged 45.1 ± 14.0 m2 were obtained and no correlation between SVL and home range size was detected (p = 0.9229, n = 20). However, removing individuals with outlier home ranges (females with home ranges > 100 m2, n = 2) resulted in a positive correlation with SVL (r = 0.61, p = 0.0072, n = 18). A 22.9 ± 5.7% overlap in home range was also detected. The small home range of A. cozumela represents the smallest home range within the Aspidoscelis genus recorded to date (including both parthenogenetic and gonochoric species) and contrasts the theoretical predictions of broad home ranges for widely foraging species. Thermoregulatory benefits and a high population density may explain the small home range of A. cozumela. Although this species is highly adapted to the environmental conditions present on the open sand beaches, anthropogenic effects on these habitats by the development of tourism infrastructure may jeopardize their existence on Cozumel Island.

Using short-range and long-range functional connectivity to identify schizophrenia with a family-based case-control design.

PubMed

Guo, Wenbin; Liu, Feng; Chen, Jindong; Wu, Renrong; Li, Lehua; Zhang, Zhikun; Chen, Huafu; Zhao, Jingping

2017-06-30

Abnormal short-range and long-range functional connectivities (FCs) have been implicated in the neurophysiology of schizophrenia. This study was conducted to examine the potential of short-range and long-range FCs for differentiating the patients from the controls with a family-based case-control design. Twenty-eight first-episode, drug-naive patients with schizophrenia, 28 unaffected siblings of the patients (family-based controls, FBCs), and 40 healthy controls (HCs) underwent resting-state functional magnetic resonance imaging (fMRI) scans. The data were analyzed by short-range and long-range FC analyses, receiver operating characteristic curve (ROC) and support vector machine (SVM). Compared with the FBCs/HCs, the patients exhibit increased short-range positive FC strength (spFCS) and/or long-range positive FC strength (lpFCS) in the default-mode network (DMN) and decreased spFCS and lpFCS in the sensorimotor circuits. Furthermore, a combination of the spFCS values in the right superior parietal lobule and the lpFCS values in the left fusiform gyrus/cerebellum VI can differentiate the patients from the FBCs with high sensitivity and specificity. The findings highlight the importance of the DMN and sensorimotor circuits in the pathogenesis of schizophrenia. Combining with family-based case-control design may be a viable option to limit the confounding effects of environmental risk factors in neuroimaging studies of schizophrenia. Copyright © 2017 Elsevier Ireland Ltd. All rights reserved.

Influence of pin and hammer mill on grinding characteristics, thermal and antioxidant properties of coriander powder.

PubMed

Barnwal, P; Singh, K K; Sharma, Alka; Choudhary, A K; Saxena, S N

2015-12-01

In present study, influence of grinding (hammer and pin mills) and moisture content (range: 6.4-13.6 % dry basis) on the quality traits of coriander powder were investigated. These include grinding parameters, colour parameters, specific heat, thermal conductivity, thermal diffusivity, glass transition temperature, essential oil, total phenolic content, total flavonoid content and DPPH scavenging (%) of coriander powder. For coriander seed, the geometric properties such as major, medium, minor dimensions, geometric mean diameter, arithmetic mean diameter, sphericity, surface area and volume of coriander seeds increased significantly with increasing moisture (6.4-13.6 % db). For coriander powder, the grinding parameters such as average particle size, volume surface mean diameter and volume mean diameter increased significantly with increasing moisture (6.4-13.6 % db). With the grinding method, the colour attributes of coriander powder such as L-value, a-value, b-value, hue angle and browning index varied significantly. It was observed that the specific heat followed second order polynomial relationship with temperature and moisture whereas thermal conductivity varied linearly with temperature and moisture content. The variation of glass transition temperature with moisture can be best represented in quadratic manner. Total flavonoid content (mg QE/g crude seed extract) and DPPH scavenging % activity of coriander powder is significantly affected by grinding methods. A lower value of specific heat was observed for hammer ground coriander powder as compared to pin mill ground coriander powder. The thermal conductivity of hammer mill ground coriander powder was higher as compared to pin mill ground coriander. It was observed that hammer mill yields more fine coriander powder in comparison to pin mill. The browning index was more in hammer mill ground coriander powder.

Cross-Cultural Applicability of the Montreal Cognitive Assessment (MoCA): A Systematic Review.

PubMed

O'Driscoll, Ciarán; Shaikh, Madiha

2017-01-01

The Montreal Cognitive Assessment (MoCA) is widely used to screen for mild cognitive impairment (MCI). While there are many available versions, the cross-cultural validity of the assessment has not been explored sufficiently. We aimed to interrogate the validity of the MoCA in a cross-cultural context: in differentiating MCI from normal controls (NC); and identifying cut-offs and adjustments for age and education where possible. This review sourced a wide range of studies including case-control studies. In addition, we report findings for differentiating dementias from NC and MCI from dementias, however, these were not considered to be an appropriate use of the MoCA. The subject of the review assumes heterogeneity and therefore meta-analyses was not conducted. Quality ratings, forest plots of validated studies (sensitivity and specificity) with covariates (suggested cut-offs, age, education and country), and summary receiver operating characteristic curve are presented. The results showed a wide range in suggested cutoffs for MCI cross-culturally, with variability in levels of sensitivity and specificity ranging from low to high. Poor methodological rigor appears to have affected reported accuracy and validity of the MoCA. The review highlights the necessity for cross-cultural considerations when using the MoCA, and recognizing it as a screen and not a diagnostic tool. Appropriate cutoffs and point adjustments for education are suggested.

Detection of plum pox virus infection in selection plum trees using spectral imaging

NASA Astrophysics Data System (ADS)

Angelova, Liliya; Stoev, Antoniy; Borisova, Ekaterina; Avramov, Latchezar

2016-01-01

Plum pox virus (PPV) is among the most studied viral diseases in the world in plants. It is considered to be one of the most devastating diseases of stone fruits in terms of agronomic impact and economic importance. Noninvasive, fast and reliable techniques are required for evaluation of the pathology in selection trees with economic impact. Such advanced tools for PPV detection could be optical techniques as light-induced fluorescence and diffuse reflectance spectroscopies. Specific regions in the electromagnetic spectra have been found to provide information about the physiological stress in plants, and consequently, diseased plants usually exhibit different spectral signature than non-stressed healthy plants in those specific ranges. In this study spectral reflectance and chlorophyll fluorescence were used for the identification of biotic stress caused by the pox virus on plum trees. The spectral responses of healthy and infected leaves from cultivars, which are widespread in Bulgaria were investigated. The two applied techniques revealed statistically significant differences between the spectral data of healthy plum leaves and those infected by PPV in the visible and near-infrared spectral ranges. Their application for biotic stress detection helps in monitoring diseases in plants using the different plant spectral properties in these spectral ranges. The strong relationship between the results indicates the applicability of diffuse reflectance and fluorescence techniques for conducting health condition assessments of vegetation and their importance for plant protection practices.

Carbon-14 Specific Activity Model Validation for Biota in Wetland Environments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yankovich, T.L.; Sharp, K.J.; Benz, M.L.

2008-01-15

In many cases, contaminants, such as radionuclides, can show highly localized spatial distributions in natural systems. Therefore, a key question for environmental assessment and monitoring becomes, how can these localized distributions of contaminants in the environment lead to organism exposure, and ultimately, the potential for effects to receptor biota? To address this question, an important first step is to conduct field surveys at sites of interest to map out the spatial distribution and extent of contaminants in areas that are being occupied and utilized by resident receptor biota. Work can then be conducted to establish predictive relationships between contaminant concentrationsmore » in biota tissues and those in environmental media with which biota interact, to gain an understanding of how representative ambient contaminant concentrations are of biota exposure. The objectives of this study were: - To conduct a field survey in a wetland ecosystem to characterize the spatial distribution of carbon- 14 ({sup 14}C), a radionuclide with dynamics in natural systems that can be described using a specific activity model; and - To determine whether {sup 14}C concentrations in environmental media reflect those measured in tissues of resident flora and fauna. A detailed field campaign was carried out in summer 2001 to characterize the spatial distribution and areal coverage of {sup 14}C in Duke Swamp, a wetland ecosystem on Atomic Energy of Canada Limited (AECL)'s Chalk River Laboratories (CRL) site that receives {sup 14}C through releases from an up-gradient Waste Management Area (WMA), primarily through groundwater influx. Sampling of surface vegetation (dominantly comprised of Sphagnum moss) was conducted at a total of 69 locations, with complementary sampling of air, soil, fungi, aerial insects, ground-dwelling insects, amphibians, small mammals and snakes being carried out at a subset of five locations with varying {sup 14}C concentrations. Concentrations of {sup 14}C in resident Duke Swamp biota were compared to levels measured in environmental media (including moss, soil and air) to determine whether concentrations in such media reflect animal exposure, for application in routine environmental monitoring programs on the CRL site. In general, for most types of receptor animals, {sup 14}C specific activities were found to be similar to or less than those measured in air, soil and surface vegetation at all locations sampled, suggesting that in most cases, estimates of {sup 14}C levels in animals could either be realistically or conservatively predicted based on the values measured in environmental media. In the case of fungi, receptor-to-media {sup 14}C specific activity ratios fell between 0.04 and 0.23 relative to air, between 0.03 and 0.70 relative to soil, and between 0.078 and 0.31 relative to moss. Small mammal specific activities also generally fell well below those that would be predicted based on specific activities measured in environmental media, with ratios ranging from 0.11 to 0.36 relative to air, from 0.17 to 0.85 relative to soil and from 0.21 to 0.58 relative to moss. Similar ratios were also established for snakes; however, a notable exception occurred for amphibians, a type of animal that tends to spend relatively more time in aquatic environments than the other species tested. In the case of Duke Swamp amphibians, animal-to-air {sup 14}C specific activity ratios ranged from 0.40 to 2.3, animal-to-soil ratios ranged from 0.81 to 3.4 and animal-to-moss ratios ranged from 1.5 to 2.4. These higher {sup 14}C levels in amphibians relative to the environmental media may be due to increased {sup 14}C exposure of aquatic or amphibious animals that occupy systems receiving inputs via groundwater. In such systems, {sup 14}C is incorporated in aquatic plants and animals, and later transferred to higher predatory species, such as amphibians, that consume them. Therefore, with the exception of amphibians and other aquatic receptor species, it is reasonable to estimate concentrations of {sup 14}C in receptor biota in wetland environments like Duke Swamp at CRL, based on measurements of {sup 14}C in environmental media, including air, soil and surface vegetation. In the case of Duke Swamp amphibians, environmental media concentrations could still be roughly predicted if they are multiplied by a 4-fold correction factor. In addition, our study findings also confirm that in cases where elevated {sup 14}C levels are highly localized, elevated exposures to resident biota are also highly localized. Such information is critical to the development of cost-effective environmental monitoring programs that are protective of nonhuman biota, while reducing the need to capture and euthanize animals during routine monitoring.« less

Analysis of borehole-radar reflection logs from selected HC boreholes at the Project Shoal area, Churchill County, Nevada

USGS Publications Warehouse

Lane, J.W.; Joesten, P.K.; Pohll, G.M.; Mihevic, Todd

2001-01-01

Single-hole borehole-radar reflection logs were collected and interpreted in support of a study to characterize ground-water flow and transport at the Project Shoal Area (PSA) in Churchill County, Nevada. Radar logging was conducted in six boreholes using 60-MHz omni-directional electric-dipole antennas and a 60-MHz magnetic-dipole directional receiving antenna.Radar data from five boreholes were interpreted to identify the location, orientation, estimated length, and spatial continuity of planar reflectors present in the logs. The overall quality of the radar data is marginal and ranges from very poor to good. Twenty-seven reflectors were interpreted from the directional radar reflection logs. Although the range of orientation interpreted for the reflectors is large, a significant number of reflectors strike northeast-southwest and east-west to slightly northwest-southeast. Reflectors are moderate to steeply dipping and reflector length ranged from less than 7 m to more than 133 m.Qualitative scores were assigned to each reflector to provide a sense of the spatial continuity of the reflector and the characteristics of the field data relative to an ideal planar reflector (orientation score). The overall orientation scores are low, which reflects the general data quality, but also indicates that the properties of most reflectors depart from the ideal planar case. The low scores are consistent with reflections from fracture zones that contain numerous, closely spaced, sub-parallel fractures.Interpretation of borehole-radar direct-wave velocity and amplitude logs identified several characteristics of the logged boreholes: (1) low-velocity zones correlate with decreased direct-wave amplitude, indicating the presence of fracture zones; (2) direct-wave amplitude increases with depth in three of the boreholes, suggesting an increase in electrical resistivity with depth resulting from changes in mineral assemblage or from a decrease in the specific conductance of ground water; and (3) an increase in primary or secondary porosity and an associated change in mineral assemblage, or decrease in ground water specific conductance, was characterized in two of the boreholes below 300 m.The results of the radar reflection logging indicate that even where data quality is marginal, borehole-radar reflection logging can provide useful information for ground-water characterization studies in fractured rock and insights into the nature and extent of fractures and fracture zones in and near boreholes.

Electrical, thermal and electrochemical properties of disordered carbon prepared from palygorskite and cane molasses

NASA Astrophysics Data System (ADS)

Alvarez, Edelio Danguillecourt; Laffita, Yodalgis Mosqueda; Montoro, Luciano Andrey; Della Santina Mohallem, Nelcy; Cabrera, Humberto; Pérez, Guillermo Mesa; Frutis, Miguel Aguilar; Cappe, Eduardo Pérez

2017-02-01

We have synthesized and electrochemically tested a carbon sample that was suitable as anode for lithium secondary battery. The synthesis was based on the use of the palygorskite clay as template and sugar cane molasses as carbon source. X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, Brunauer-Emmett-Teller (BET) measurements and High Resolution Transmission Electron Microscope (HRTEM) analysis showed that the nanometric carbon material has a highly disordered graphene-like wrinkled structure and large specific surface area (467 m2 g-1). The compositional characterization revealed a 14% of heteroatoms-containing groups (O, H, N, S) doping the as-prepared carbon. Thermophysical measurements revealed the good thermal stability and an acceptable thermal diffusivity (9·10-7 m2 s-1) and conductivity (1.1 W m-1 K-1) of this carbon. The electrical properties showed an electronic conductivity of hole-like carriers of approximately one S/cm in a 173-293 K range. The testing of this material as anodes in a secondary lithium battery displayed a high specific capacity and excellent performance in terms of number of cycles. A high reversible capacity of 356 mA h g-1 was reached.

Comparison of approaches to Total Quality Management. Including an examination of the Department of Energy`s position on quality management

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bennett, C.T.

1994-03-01

This paper presents a comparison of several qualitatively different approaches to Total Quality Management (TQM). The continuum ranges from management approaches that are primarily standards -- with specific guidelines, but few theoretical concepts -- to approaches that are primarily philosophical, with few specific guidelines. The approaches to TQM discussed in this paper include the International Organization for Standardization (ISO) 9000 Standard, the Malcolm Baldrige National Quality Award, Senge`s the Learning Organization, Watkins and Marsick`s approach to organizational learning, Covey`s Seven Habits of Highly Successful People, and Deming`s Fourteen Points for Management. Some of these approaches (Deming and ISO 9000) aremore » then compared to the DOE`s official position on quality management and conduct of operations (DOE Orders 5700.6C and 5480.19). Using a tabular format, it is shown that while 5700.6C (Quality Assurance) maps well to many of the current approaches to TQM, DOE`s principle guide to management Order 5419.80 (Conduct of Operations) has many significant conflicts with some of the modern approaches to continuous quality improvement.« less

Investigation of coal properties and airborne respirable dust generation. Report of investigations/1998

DOE Office of Scientific and Technical Information (OSTI.GOV)

Organiscak, J.A.; Page, S.J.

1998-10-01

Laboratory crushing experiments were conducted on a range of low- to high-volatile bituminous coals to investigate the various factors influencing airborne respirable dust (ARD) generation. This research was conducted to identify the principles of ARD liberation from the coal product. Five U.S. bituminous coals were uniformly prepared and processed through a double roll crusher located in a low-velocity wind tunnel. Experimental factors studied included inherent coal seam constituents, coal grindability, specific energy of crushing, product size characteristics, dust cloud electrostatic field, and specific ARD generated. The results of this investigation indicate that a combination of several factors are associated withmore » ARD generation. One factor is the effect of coal rank, described by the inherent moist fuel ratio, on the product size characteristics, defined by Schuhmann size function parameters. Another key factor is the effect of air dry loss (ADL) moisture in the coal seam on the breakage-induced electrostatic field of airborne dust. The effect of these factors is that different percentages of <10-micrometers coal particles are dispersed as ARD. A discussion of electrostatic field principles, coal ADL, and its effect on ARD generation is presented.« less

Water quality of Rhode Island streams

USGS Publications Warehouse

Briggs, J.C.; Feiffer, J.S.

1986-01-01

Water quality data collected from November 1979 through September 1983 at five stream stations within Rhode Island and one in Massachusetts show that concentrations of the common constituents were low. Mean water hardness at all sites was in the ' soft ' category. Sodium concentrations were less than 20 mg/L at two sites and less than 35 mg/L at the other sites. Mean nitrogen values for the two Blackstone River sites were in the range that could cause undesirable growths of aquatic plants. Mean phosphorus values exceeded the recommended limits for protection of aquatic life at four sites. Trace-element concentrations in the water were generally low. Those trace elements which were found in concentrations near or exceeding any standard or criterion include cadmium, chromium, lead, iron, and manganese. High concentrations of several trace elements were found in the bottom materials at several sites. The bottom materials also contained pesticides and organic chemicals including aldrin, chlordane, DDD, DDE, DDT, dieldren, endosulfan , endrin, heptachlor, Mirex, and PCB. Results of trend analysis of total phosphorus, total nitrogen, and specific conductance show a downward trend in phosphorus at two sites; an upward trend in nitrogen at one site; and one downward trend and one upward trend in specific conductance. (USGS)

Climate-water quality relationships in Texas reservoirs

USGS Publications Warehouse

Gelca, Rodica; Hayhoe, Katharine; Scott-Fleming, Ian; Crow, Caleb; Dawson, D.; Patino, Reynaldo

2015-01-01

Water temperature, dissolved oxygen, and concentrations of salts in surface water bodies can be affected by the natural environment, local human activities such as surface and ground water withdrawals, land use, and energy extraction, and variability and long-term trends in atmospheric conditions including temperature and precipitation. Here, we quantify the relationship between 121 indicators of mean and extreme temperature and precipitation and 24 water quality parameters in 57 Texas reservoirs using observational data records covering the period 1960 to 2010. We find that water temperature, dissolved oxygen, pH, specific conductance, chloride, sulfate, and phosphorus all show consistent correlations with atmospheric predictors, including high and low temperature extremes, dry days, heavy precipitation events, and mean temperature and precipitation over time scales ranging from one week to two years. Based on this analysis and published future projections for this region, we expect climate change to increase water temperatures, decrease dissolved oxygen levels, decrease pH, increase specific conductance, and increase levels of sulfate, chloride in Texas reservoirs. Over decadal time scales, this may affect aquatic ecosystems in the reservoirs, including altering the risk of conditions conducive to algae occurrence, as well as affecting the quality of water available for human consumption and recreation.

Chemical composition and variability of the waters of the Edwards Plateau, central Texas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Groeger, A.W.; Gustafson, J.J.

1994-12-31

The surface waters of the karstic Edwards Plateau, southcentral Texas, are quite similar in many of their chemical characteristics. The ionic composition of the water was dominated by calcium and alkalinity (mostly bicarbonate) acquired through limestone weathering, and the ionic composition (in equivalents) was Ca>Mg>Na>K and alkalinity >Cl and SO{sub 4}. The median specific conductance and total dissolved solids ranged from 394 to 535 {mu}S cm{sup {minus}1} and 220 and 327 mg L{sup {minus}1}, respectively. The streams were always near or at supersaturation with respect to calcium carbonate, and the dynamics of calcium carbonate dissolution and precipitation tended to maintainmore » the dissolved substances at a fairly constant level. This may have been enhanced by the intimate contact of water and bedrock characteristic of karst drainages. Specific conductance, Ca, and alkalinity all decreased at higher summer temperatures. Many of the streams on the plateau maintained a constant level or actually increased concentrations of total dissolved substances at increased flow rates. These waters acquired significant quantities of solute as they flow through the confine Edwards Aquifer, including alkalinity, Ca, Mg, Na, Cl, and NO{sub 3}.« less

Parametric study of the physical properties of hydrate-bearing sand, silt, and clay sediments: 1. Electromagnetic properties

USGS Publications Warehouse

Lee, J.Y.; Santamarina, J.C.; Ruppel, C.

2010-01-01

The marked decrease in bulk electrical conductivity of sediments in the presence of gas hydrates has been used to interpret borehole electrical resistivity logs and, to a lesser extent, the results of controlled source electromagnetic surveys to constrain the spatial distribution and predicted concentration of gas hydrate in natural settings. Until now, an exhaustive laboratory data set that could be used to assess the impact of gas hydrate on the electromagnetic properties of different soils (sand, silt, and clay) at different effective stress and with different saturations of hydrate has been lacking. The laboratory results reported here are obtained using a standard geotechnical cell and the hydrate-formed tetrahydrofuran (THF), a liquid that is fully miscible in water and able to produce closely controlled saturations of hydrate from dissolved phase. Both permittivity and electrical conductivity are good indicators of the volume fraction of free water in the sediment, which is in turn dependent on hydrate saturation. Permittivity in the microwave frequency range is particularly predictive of free water content since it is barely affected by ionic concentration, pore structure, and surface conduction. Electrical conductivity (or resistivity) is less reliable for constraining water content or hydrate saturation: In addition to fluid-filled porosity, other factors, such as the ionic concentration of the pore fluid and possibly other conduction effects (e.g., surface conduction in high specific surface soils having low conductivity pore fluid), also influence electrical conductivity.

Bullying and victimization among black and Hispanic adolescents.

PubMed

Peskin, Melissa Fleschler; Tortolero, Susan R; Markham, Christine M

2006-01-01

The prevalence of bullying and victimization by gender, grade level, and race/ethnicity was examined among a sample of low socioeconomic, Black and Hispanic 6th- to 12th-graders in a large urban school district in Texas. Bullying and victimization were measured using specific behaviors. Students were classified as bullies (7%), victims (12%), bully-victims (5%), or neither (76%), depending on the number and frequency of reported experiences. For specific types of bullying (e.g., spreading rumors, excluding others), 4.5%-9.4% of students reported participation. Specific types of victimization (e.g., being hit or pushed, picked on) ranged from 6%-12%. Gender differences were not observed for general bullying and victimization, but physical and some verbal types were more prevalent among males. Blacks were more likely to participate in bullying and victimization, and these experiences seemed to peak in the 9th grade. This study adds to the literature as few U.S. studies on both general and specific types of bullying have been conducted among low socioeconomic, racial/ethnic minority students in middle and high school.

Using reduced graphene oxide-Ca:CdSe nanocomposite to enhance photoelectrochemical activity of gold nanoparticles functionalized tungsten oxide for highly sensitive prostate specific antigen detection.

PubMed

Wang, Xueping; Xu, Rui; Sun, Xu; Wang, Yaoguang; Ren, Xiang; Du, Bin; Wu, Dan; Wei, Qin

2017-10-15

An ultrasensitive sandwich-type photoelectrochemical (PEC) immunosensor was constructed for the detection of prostate specific antigen (PSA). In this work, Au-nanoparticle-loaded tungsten oxide (WO 3 -Au) hybrid composites was applied as PEC sensing platform, while Ca ions doped CdSe equipped on the conducting framework of reduced graphene oxide (rGO-Ca:CdSe) nanocomposites were employed as the signal amplification probe. As for WO 3 -Au, massive Au nanoparticles were formed on the surface of WO 3 without any additional reducing agent, providing a novel nanocarriers for anchoring plenty of the primary antibodies due to the large specific surface area and good biocompatibility by chemical bonding between Au nanoparticles and -NH 2 of antibodies. Besides, the incorporation of the rGO and the doping of Ca ions could improve the conductivity and hinder the recombination of electron-hole pairs of CdSe nanoparticles effectively, thereby enhancing the photocurrent conversion efficiency. Based on the sandwich immunoreaction, the primary antibody was immobilized onto WO 3 -Au substrate, after the formed rGO-Ca:CdSe labels were captured onto the electrode surface via the specific antibody-antigen interaction, the photocurrent intensity could be further enhanced due to the sensitization effect. Under the optimal conditions, the proposed PEC immunosensor shows a linear relationship between photocurrent variation and the logarithm of PSA concentration in the wide range of 5pgmL -1 to 50ngmL -1 with a low detection limit of 2.6pgmL -1 (S/N=3). Moreover, it also presented good stability and acceptable specificity, indicating the potential applications in clinical diagnostics. Copyright © 2017 Elsevier B.V. All rights reserved.

Ionic Liquids as Electrolytes for Electrochemical Double-Layer Capacitors: Structures that Optimize Specific Energy.

PubMed

Mousavi, Maral P S; Wilson, Benjamin E; Kashefolgheta, Sadra; Anderson, Evan L; He, Siyao; Bühlmann, Philippe; Stein, Andreas

2016-02-10

Key parameters that influence the specific energy of electrochemical double-layer capacitors (EDLCs) are the double-layer capacitance and the operating potential of the cell. The operating potential of the cell is generally limited by the electrochemical window of the electrolyte solution, that is, the range of applied voltages within which the electrolyte or solvent is not reduced or oxidized. Ionic liquids are of interest as electrolytes for EDLCs because they offer relatively wide potential windows. Here, we provide a systematic study of the influence of the physical properties of ionic liquid electrolytes on the electrochemical stability and electrochemical performance (double-layer capacitance, specific energy) of EDLCs that employ a mesoporous carbon model electrode with uniform, highly interconnected mesopores (3DOm carbon). Several ionic liquids with structurally diverse anions (tetrafluoroborate, trifluoromethanesulfonate, trifluoromethanesulfonimide) and cations (imidazolium, ammonium, pyridinium, piperidinium, and pyrrolidinium) were investigated. We show that the cation size has a significant effect on the electrolyte viscosity and conductivity, as well as the capacitance of EDLCs. Imidazolium- and pyridinium-based ionic liquids provide the highest cell capacitance, and ammonium-based ionic liquids offer potential windows much larger than imidazolium and pyridinium ionic liquids. Increasing the chain length of the alkyl substituents in 1-alkyl-3-methylimidazolium trifluoromethanesulfonimide does not widen the potential window of the ionic liquid. We identified the ionic liquids that maximize the specific energies of EDLCs through the combined effects of their potential windows and the double-layer capacitance. The highest specific energies are obtained with ionic liquid electrolytes that possess moderate electrochemical stability, small ionic volumes, low viscosity, and hence high conductivity, the best performing ionic liquid tested being 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide.

Inversion of multi-frequency electromagnetic induction data for 3D characterization of hydraulic conductivity

USGS Publications Warehouse

Brosten, Troy R.; Day-Lewis, Frederick D.; Schultz, Gregory M.; Curtis, Gary P.; Lane, John W.

2011-01-01

Electromagnetic induction (EMI) instruments provide rapid, noninvasive, and spatially dense data for characterization of soil and groundwater properties. Data from multi-frequency EMI tools can be inverted to provide quantitative electrical conductivity estimates as a function of depth. In this study, multi-frequency EMI data collected across an abandoned uranium mill site near Naturita, Colorado, USA, are inverted to produce vertical distribution of electrical conductivity (EC) across the site. The relation between measured apparent electrical conductivity (ECa) and hydraulic conductivity (K) is weak (correlation coefficient of 0.20), whereas the correlation between the depth dependent EC obtained from the inversions, and K is sufficiently strong to be used for hydrologic estimation (correlation coefficient of − 0.62). Depth-specific EC values were correlated with co-located K measurements to develop a site-specific ln(EC)–ln(K) relation. This petrophysical relation was applied to produce a spatially detailed map of K across the study area. A synthetic example based on ECa values at the site was used to assess model resolution and correlation loss given variations in depth and/or measurement error. Results from synthetic modeling indicate that optimum correlation with K occurs at ~ 0.5 m followed by a gradual correlation loss of 90% at 2.3 m. These results are consistent with an analysis of depth of investigation (DOI) given the range of frequencies, transmitter–receiver separation, and measurement errors for the field data. DOIs were estimated at 2.0 ± 0.5 m depending on the soil conductivities. A 4-layer model, with varying thicknesses, was used to invert the ECa to maximize available information within the aquifer region for improved correlations with K. Results show improved correlation between K and the corresponding inverted EC at similar depths, underscoring the importance of inversion in using multi-frequency EMI data for hydrologic estimation.

Inversion of multi-frequency electromagnetic induction data for 3D characterization of hydraulic conductivity

USGS Publications Warehouse

Brosten, T.R.; Day-Lewis, F. D.; Schultz, G.M.; Curtis, G.P.; Lane, J.W.

2011-01-01

Electromagnetic induction (EMI) instruments provide rapid, noninvasive, and spatially dense data for characterization of soil and groundwater properties. Data from multi-frequency EMI tools can be inverted to provide quantitative electrical conductivity estimates as a function of depth. In this study, multi-frequency EMI data collected across an abandoned uranium mill site near Naturita, Colorado, USA, are inverted to produce vertical distribution of electrical conductivity (EC) across the site. The relation between measured apparent electrical conductivity (ECa) and hydraulic conductivity (K) is weak (correlation coefficient of 0.20), whereas the correlation between the depth dependent EC obtained from the inversions, and K is sufficiently strong to be used for hydrologic estimation (correlation coefficient of -0.62). Depth-specific EC values were correlated with co-located K measurements to develop a site-specific ln(EC)-ln(K) relation. This petrophysical relation was applied to produce a spatially detailed map of K across the study area. A synthetic example based on ECa values at the site was used to assess model resolution and correlation loss given variations in depth and/or measurement error. Results from synthetic modeling indicate that optimum correlation with K occurs at ~0.5m followed by a gradual correlation loss of 90% at 2.3m. These results are consistent with an analysis of depth of investigation (DOI) given the range of frequencies, transmitter-receiver separation, and measurement errors for the field data. DOIs were estimated at 2.0??0.5m depending on the soil conductivities. A 4-layer model, with varying thicknesses, was used to invert the ECa to maximize available information within the aquifer region for improved correlations with K. Results show improved correlation between K and the corresponding inverted EC at similar depths, underscoring the importance of inversion in using multi-frequency EMI data for hydrologic estimation. ?? 2011.

Branch age and light conditions determine leaf-area-specific conductivity in current shoots of Scots pine.

PubMed

Grönlund, Leila; Hölttä, Teemu; Mäkelä, Annikki

2016-08-01

Shoot size and other shoot properties more or less follow the availability of light, but there is also evidence that the topological position in a tree crown has an influence on shoot development. Whether the hydraulic properties of new shoots are more regulated by the light or the position affects the shoot acclimation to changing light conditions and thereby to changing evaporative demand. We investigated the leaf-area-specific conductivity (and its components sapwood-specific conductivity and Huber value) of the current-year shoots of Scots pine (Pinus sylvestris L.) in relation to light environment and topological position in three different tree classes. The light environment was quantified in terms of simulated transpiration and the topological position was quantified by parent branch age. Sample shoot measurements included length, basal and tip diameter, hydraulic conductivity of the shoot, tracheid area and density, and specific leaf area. In our results, the leaf-area-specific conductivity of new shoots declined with parent branch age and increased with simulated transpiration rate of the shoot. The relation to transpiration demand seemed more decisive, since it gave higher R(2) values than branch age and explained the differences between the tree classes. The trend of leaf-area-specific conductivity with simulated transpiration was closely related to Huber value, whereas the trend of leaf-area-specific conductivity with parent branch age was related to a similar trend in sapwood-specific conductivity. © The Author 2016. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Evaluation of Amount of Blood in Dry Blood Spots: Ring-Disk Electrode Conductometry.

PubMed

Kadjo, Akinde F; Stamos, Brian N; Shelor, C Phillip; Berg, Jordan M; Blount, Benjamin C; Dasgupta, Purnendu K

2016-06-21

A fixed area punch in dried blood spot (DBS) analysis is assumed to contain a fixed amount of blood, but the amount actually depends on a number of factors. The presently preferred approach is to normalize the measurement with respect to the sodium level, measured by atomic spectrometry. Instead of sodium levels, we propose electrical conductivity of the extract as an equivalent nondestructive measure. A dip-type small diameter ring-disk electrode (RDE) is ideal for very small volumes. However, the conductance (G) measured by an RDE depends on the depth (D) of the liquid below the probe. There is no established way of computing the specific conductance (σ) of the solution from G. Using a COMSOL Multiphysics model, we were able to obtain excellent agreement between the measured and the model predicted conductance as a function of D. Using simulations over a large range of dimensions, we provide a spreadsheet-based calculator where the RDE dimensions are the input parameters and the procedure determines the 99% of the infinite depth conductance (G99) and the depth D99 at which this is reached. For typical small diameter probes (outer electrode diameter ∼ <2 mm), D99 is small enough for dip-type measurements in extract volumes of ∼100 μL. We demonstrate the use of such probes with DBS extracts. In a small group of 12 volunteers (age 20-66), the specific conductance of 100 μL aqueous extracts of 2 μL of spotted blood showed a variance of 17.9%. For a given subject, methanol extracts of DBS spots nominally containing 8 and 4 μL of blood differed by a factor of 1.8-1.9 in the chromatographically determined values of sulfate and chloride (a minor and major constituent, respectively). The values normalized with respect to the conductance of the extracts differed by ∼1%. For serum associated analytes, normalization of the analyte value by the extract conductance can thus greatly reduce errors from variations in the spotted blood volume/unit area.

Development of the first infrared satellite observatory

NASA Technical Reports Server (NTRS)

Smith, G. M.; Squibb, G. F.

1984-01-01

A development history is given for the Infrared Astronomical Satelite (IRAS), whose primary mission objective is an unbiased, all-sky survey in the 8-120 micron wavelength range. A point source catalog of more than 200,000 IR sources, to be published later this year, represents the accomplishment of this objective. IRAS has also conducted 10,000 pointed observations of specific objects. Attention is given to the cost increases and schedule slips which resulted from the substantial technical challenges of IRAS hardware and software development, and to the management techniques which had to be employed in this major international project.

Sub-millikelvin stabilization of a closed cycle cryocooler.

PubMed

Dubuis, Guy; He, Xi; Božović, Ivan

2014-10-01

Intrinsic temperature oscillations (with the amplitude up to 1 K) of a closed cycle cryocooler are stabilized by a simple thermal damping system. It employs three different materials with different thermal conductivity and specific heat at various temperatures. The amplitude of oscillations of the sample temperature is reduced to less than 1 mK, in the temperature range from 4 K to 300 K, while the cooling power is virtually undiminished. The damping system is small, inexpensive, can be retrofitted to most existing closed cycle cryocoolers, and may improve measurements of any temperature-sensitive physics properties.

Digital computer program for nuclear reactor design water properties (LWBR Development Program)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lynn, L.L.

1967-07-01

An edit program MO899 for the tabulation of thermodynamic and transport properties of liquid and vapor water, frequently used in design calculations for pressurized water nuclear reactors, is described. The data tabulated are obtained from a FORTRAN IV subroutine named HOH. Values of enthalpy, specific volume, viscosity, and thermal conductivity are given for the following ranges: pressure from one bar (14.5 psia) to 175 bars (2538 psia) and temperature from as much as 320 deg C (608 deg F) below saturation up to 500 deg C (932 deg F) above saturation. (NSA 21: 38472)

Bonded and Sealed External Insulations for Liquid-Hydrogen-Fueled Rocket Tanks During Atmospheric Flight

NASA Technical Reports Server (NTRS)

Gray, V. H.; Gelder, T. F.; Cochran, R. P.; Goodykoontz, J. H.

1960-01-01

Several currently available nonmetallic insulation materials that may be bonded onto liquid-hydrogen tanks and sealed against air penetration into the insulation have been investigated for application to rockets and spacecraft. Experimental data were obtained on the thermal conductivities of various materials in the cryogenic temperature range, as well as on the structural integrity and ablation characteristics of these materials at high temperatures occasioned by aerodynamic heating during atmospheric escape. Of the materials tested, commercial corkboard has the best overall properties for the specific requirements imposed during atmospheric flight of a high-acceleration rocket vehicle.

Effect of humidity on fretting wear of several pure metals

NASA Technical Reports Server (NTRS)

Goto, H.; Buckley, D. H.

1984-01-01

Fretting wear experiments with several pure metals were conducted in air at various relative humidity levels. The materials used were iron, aluminum, copper, silver, chromium, titanium, and nickel. Each pure metal had a maximum fretting wear volume at a specific humidity level RH sub max that was not dependent on mechanical factors such as contact load, fretting amplitude, and frequency in the ranges studied. The weight loss due to fretting wear at RH sub max for each pure metal decreased with increasing heat of oxygen adsorption on the metal, indicating that adhesive wear dominated at RH sub max.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sharma, Anupam Deep, E-mail: dr.anupamdeep@yahoo.com; Sinha, M. M.

Perovskite oxides find wide range of applications like oxygen sensors, catalyst support, high frequency capacitors, high temperature superconducting microwave devices, solid state oxide fuel cell (SOFC) etc. LaAlO{sub 3} is one of such type of prominent perovskite oxides and very prominent material for protonic conductions. Therefore knowledge of the thermal properties of LaAlO{sub 3} is most significant. Hence in the present study we have studied phonon density of states and specific heat of LaAlO{sub 3} in cubic structure by applying lattice dynamical theoretical model. The calculated results are interpreted with existing experimental or theoretical results.

Extreme ultraviolet quantum efficiency of opaque alkali halide photocathodes on microchannel plates

NASA Technical Reports Server (NTRS)

Siegmund, O. H. W.; Everman, E.; Vallerga, J. V.; Lampton, M.

1988-01-01

Comprehensive measurements are presented for the quantum detection efficiency (QDE) of the microchannel plate materials CsI, KBr, KCl, and MgF2, over the 44-1800 A wavelength range. QDEs in excess of 40 percent are achieved by several materials in specific wavelength regions of the EUV. Structure is noted in the wavelength dependence of the QDE that is directly related to the valence-band/conduction-band gap energy and the onset of atomic-like resonant transitions. A simple photocathode model allows interpretation of these features, together with the QDE efficiency variation, as a function of illumination angle.

Syringotropic mycosis fungoides: clinical and histologic features, response to treatment, and outcome in 19 patients.

PubMed

de Masson, Adèle; Battistella, Maxime; Vignon-Pennamen, Marie-Dominique; Cavelier-Balloy, Bénédicte; Mouly, Frédéric; Rybojad, Michel; Bouaziz, Jean-David; Petit, Antoine; Saussine, Anne; Ronceray, Sophie; Le Gall, François; Ram-Wolff, Caroline; Assouly, Philippe; Dereure, Olivier; Joly, Pascal; Dallot, Alexiane; Dupuy, Alain; Lebbé, Céleste; Moulonguet, Isabelle; Rivet, Jacqueline; Janin, Anne; Bagot, Martine

2014-11-01

A rare variant of mycosis fungoides (MF), syringotropic MF (STMF) is characterized by a particular tropism of the lymphocytic infiltrate for the eccrine structures, and included in the follicular subtype of MF in the World Health Organization-European Organization for Research and Treatment of Cancer classification of cutaneous lymphomas. We sought to determine the clinicopathologic features and disease course of patients with STMF. A retrospective study was conducted to identify patients with STMF from 1998 to 2013. Nineteen patients were included: 15 men and 4 women, mean age 55 years (range, 24-86). Most had multiple lesions (n=16, 84%) with associated alopecia (n=12, 63%) and/or punctuated aspect (n=12, 63%). Palms or soles were involved in 10 cases (53%). Folliculotropism was found in 13 cases (68%). After a median follow-up of 70 months (range, 2-140), 3 patients died, 1 from disease-related death. The 5-year overall and disease-specific survival were 100%. The disease-specific survival was significantly higher than in 54 patients with folliculotropic MF without syringotropism (5-year disease-specific survival, 74%; 95% confidence interval, 58%-94%, P=.02). Retrospective setting is a limitation. In the spectrum of adnexotropic MF, STMF appears as a distinct entity from follicular MF, with peculiar clinical characteristics and natural history. Copyright © 2014 American Academy of Dermatology, Inc. Published by Elsevier Inc. All rights reserved.

Transport of Cryptosporidium, Giardia, Source-specific Indicator Organisms, and Standard Water Quality Constituents During Storm Events

NASA Astrophysics Data System (ADS)

Sturdevant-Rees, P. L.; Bourdeau, D.; Baker, R.; Long, S. C.; Barten, P. K.

2004-05-01

Microbial and water-quality measurements are collected during storm events under a variety of meteorological and land-use conditions in order to 1) identify risk of Cryptosporidium oocysts, Giardia cysts and other constituents, including microbial indicator organisms, entering surface waters from various land uses during periods of surface runoff; 2) optimize storm sampling procedures for these parameters; and 3) optimize strategies for accurate determination of constituent loads. The investigation is focused on four isolated land uses: forested with free ranging wildlife, beaver influenced forested with free ranging wildlife, residential/commercial, and dairy farm grazing/pastureland using an upstream and downstream sampling strategy. Traditional water-quality analyses include pH, temperature, turbidity, conductivity, total suspended solids, total phosphorus, total Kjeldahl-nitrogen, and ammonia nitrogen, Giardia cysts and Cryptosporidium oocysts. Total coliforms and fecal coliforms are measured as industry standard microbial analyses. Sorbitol-fermenting Bifidobacteria, Rhodococcus coprophilus, Clostridium perfringens spores, and Somatic and F-specific coliphages are measured at select sites as potential alternative source-specific indicator organisms. Upon completion of the project, the final database will consist of wet weather transport data for a set of parameters during twenty-four distinct storm-events in addition to monthly baseline data. A subset of the results to date will be presented, with focus placed on demonstrating the impact of beaver on constituent loadings over a variety of hydrologic and meteorological conditions.

Appraisal of data for ground-water quality in Nebraska

USGS Publications Warehouse

Engberg, R.A.

1984-01-01

This report summarizes existing data for groundwater quality in Nebraska and indicates their adequacy as a data base. Analyses have been made of water from nearly 10,000 wells by 8 agencies. Those analyses that meet reliability criteria have been aggregated by geologic source of water into four principal aquifer groupings--Holocene-Pleistocene aquifers, Tertiary aquifers, Mesozoic aquifers, and Paleozoic aquifers. For each aquifer grouping, data for specific conductance and 24 constituents in the water are summarized statistically. Also, diagrams are presented showing differences in statistical parameters, or in chemical composition, of water from the different aquifer groupings. Additionally, for each grouping except Paleozoic aquifers, maps show ranges in concentration of dissolved solids, calcium, alkalinity, and sulfate. In areas where data are insufficient to delimit, ranges in concentration also are shown on the maps. Point-source contamination has been identified at 41 locations and nonpoint-source contamination in 3 areas, namely, the central Platte Valley, Holt County, and Boyd County. Potential for nonpoint-source contamination exists in 10 major areas, which together comprise more than one-third of the State. Existing data are mostly from specific projects having limited areas and objectives. Consequently, a lack of data exists for other areas and for certain geologic units, particularly the Mesozoic and Paleozoic aquifers. Specific data needs for each of the four principal aquifer groupings are indicated in a matrix table.

Consumers' use of written product information.

PubMed

Wiese, Bettina S; Sauer, Jürgen; Rüttinger, Bruno

2004-09-15

Two studies were conducted to investigate the predictive role of person-specific, product-specific, and situation-specific influences on the use of instruction manuals in the field of electrical consumer products. In a laboratory study, 42 participants were observed while putting a vacuum cleaner into operation. Situational primes (i.e., receiving a verbal cue that the packaging contains an instruction manual) increased the probability of the user manual being read. Additional verbal information that the manual contains information on energy-saving behaviours was especially motivating for persons with high environmental concern. Self-report data, collected on a wide range of products, suggest that product complexity is the best predictor of instruction manual use. In a second study with 30 participants, different positions of product labels were compared, i.e. placing the information on the packaging or directly onto the product. Information placed directly onto the product had a significantly higher influence on participants' actual behaviour than providing the same information on the packaging.

Species-specific control of external superoxide levels by the coral holobiont during a natural bleaching event

NASA Astrophysics Data System (ADS)

Diaz, Julia M.; Hansel, Colleen M.; Apprill, Amy; Brighi, Caterina; Zhang, Tong; Weber, Laura; McNally, Sean; Xun, Liping

2016-12-01

The reactive oxygen species superoxide (O2.-) is both beneficial and detrimental to life. Within corals, superoxide may contribute to pathogen resistance but also bleaching, the loss of essential algal symbionts. Yet, the role of superoxide in coral health and physiology is not completely understood owing to a lack of direct in situ observations. By conducting field measurements of superoxide produced by corals during a bleaching event, we show substantial species-specific variation in external superoxide levels, which reflect the balance of production and degradation processes. Extracellular superoxide concentrations are independent of light, algal symbiont abundance and bleaching status, but depend on coral species and bacterial community composition. Furthermore, coral-derived superoxide concentrations ranged from levels below bulk seawater up to ~120 nM, some of the highest superoxide concentrations observed in marine systems. Overall, these results unveil the ability of corals and/or their microbiomes to regulate superoxide in their immediate surroundings, which suggests species-specific roles of superoxide in coral health and physiology.

Aptamers in Diagnostics and Treatment of Viral Infections

PubMed Central

Wandtke, Tomasz; Woźniak, Joanna; Kopiński, Piotr

2015-01-01

Aptamers are in vitro selected DNA or RNA molecules that are capable of binding a wide range of nucleic and non-nucleic acid molecules with high affinity and specificity. They have been conducted through the process known as SELEX (Systematic Evolution of Ligands by Exponential Enrichment). It serves to reach specificity and considerable affinity to target molecules, including those of viral origin, both proteins and nucleic acids. Properties of aptamers allow detecting virus infected cells or viruses themselves and make them competitive to monoclonal antibodies. Specific aptamers can be used to interfere in each stage of the viral replication cycle and also inhibit its penetration into cells. Many current studies have reported possible application of aptamers as a treatment or diagnostic tool in viral infections, e.g., HIV (Human Immunodeficiency Virus), HBV (Hepatitis B Virus), HCV (Hepatitis C Virus), SARS (Severe Acute Respiratory Syndrome), H5N1 avian influenza and recently spread Ebola. This review presents current developments of using aptamers in the diagnostics and treatment of viral diseases. PMID:25690797

Melting temperature and enthalpy variations of phase change materials (PCMs): a differential scanning calorimetry (DSC) analysis

NASA Astrophysics Data System (ADS)

Sun, Xiaoqin; Lee, Kyoung Ok; Medina, Mario A.; Chu, Youhong; Li, Chuanchang

2018-06-01

Differential scanning calorimetry (DSC) analysis is a standard thermal analysis technique used to determine the phase transition temperature, enthalpy, heat of fusion, specific heat and activation energy of phase change materials (PCMs). To determine the appropriate heating rate and sample mass, various DSC measurements were carried out using two kinds of PCMs, namely N-octadecane paraffin and calcium chloride hexahydrate. The variations in phase transition temperature, enthalpy, heat of fusion, specific heat and activation energy were observed within applicable heating rates and sample masses. It was found that the phase transition temperature range increased with increasing heating rate and sample mass; while the heat of fusion varied without any established pattern. The specific heat decreased with the increase of heating rate and sample mass. For accuracy purpose, it is recommended that for PCMs with high thermal conductivity (e.g. hydrated salt) the focus will be on heating rate rather than sample mass.

Polaronic conductivity and scaling behavior of lithium iron phosphate glass

NASA Astrophysics Data System (ADS)

Banday, Azeem; Murugavel, Sevi

2018-05-01

Charge transport properties of the Lithium Iron Phosphate (LFP) glass has been investigated in a wide frequency and temperature range by means of broadband dielectric spectroscopy. The conductivity spectra has been studied on the basis of Jonscher power law for characterizing the hopping dynamics of charge carriers. The ac conductivity and scaling behavior of the LFP glass has been studied in the temperature range from 333K to 573K and frequency range from 100 mHz to 1 MHz. The conductivity isotherms of LFP glass do not superimpose upon each other by using Summerfield scaling. The structural peculiarities in the material could result in different conduction pathways giving rise to the deviation from Summerfield scaling.

Hydrogeologic framework and simulation of ground-water flow and travel time in the shallow aquifer system in the area of Naval Support Activity Memphis, Millington, Tennessee

USGS Publications Warehouse

Robinson, James L.; Carmichael, John K.; Halford, Keith J.; Ladd, David E.

1997-01-01

Naval Support Activity (NSA) Memphis is a Department of the Navy facility located at the City of Millington, Tennessee, about 5 miles north of Memphis. Contaminants have been detected in surface-water, sediment, and ground-water samples collected at the facility. As part of the Installation Restoration Program, the Navy is considering remedial-action options to prevent or lessen the effect of ground-water contamination at the facility and to control the movement and discharge of contaminants. A numerical model of the ground-water-flow system in the area of NSA Memphis was constructed and calibrated so that quantifiable estimates could be made of ground-water-flow rates, direction, and time-of-travel. The sediments beneath NSA Memphis, to a depth of about 200 feet, form a shallow aquifer system. From youngest to oldest, the stratigraphic units that form the shallow aquifer system are alluvium, loess, fluvial deposits, and the Cockfield and Cook Mountain Formations. The shallow aquifer system is organized into five hydrogeologic units: (1) a confining unit composed of the relatively low permeability sediments of the upper alluvium and the loess; (2) the A1 aquifer comprising sand and gravel of the lower alluvium and the fluvial deposits, and sand lenses in the upper part of the preserved section of the Cockfield Formation; (3) a confining unit composed of clay and silt within the upper part of the Cockfield Formation; (4) the Cockfield aquifer comprising sand lenses within the lower part of the preserved section of the Cockfield Formation; and (5) a confining unit formed by low permeability sediments of the Cook Mountain Formation that composes the upper confining unit for the Memphis aquifer. Thicknesses of individual units vary considerably across the facility. Structural and depositional features that affect the occurrence of ground water in the shallow aquifer system include faulting, an erosional scarp, and 'windows' in the confining units. Underlying the shallow aquifer system is the Memphis aquifer, the primary source of water for NSA Memphis and the City of Memphis, Tennessee. Analyses of sediment cores, aquifer and well specific-capacity tests, and numerical modeling were used to estimate the hydraulic characteristics of units of the shallow aquifer system. The vertical hydraulic conductivity of core samples of the alluvium-loess confining unit ranged from about 8.5 x 10-5 to 1.6 x 10-2 feet per day, and the total porosity of the samples ranged from about 35 to 48 percent. The results of the aquifer test were used to estimate a horizontal hydraulic conductivity of about 5 feet per day for the alluvial-fluvial deposits aquifer. The total porosity of core samples of the alluvial-fluvial deposits aquifer ranged from about 22 to 39 percent. The vertical hydraulic conductivity of core samples of the Cockfield confining unit ranged from about 4.5 x 10-5 to 2.5 x 10-3 feet per day, and the total porosity ranged from about 41 to 55 percent. Well specific-capacity tests indicate that the horizontal hydraulic conductivity of sand units that compose the Cockfield aquifer range from about 0.5 to 3 feet per day. The vertical hydraulic conductivity of core samples of the Cook Mountain confining unit ranged from about 5.0 x 10-6 to 9.9 x 10-4 feet per day. Total porosity of core samples of the Cook Mountain confining unit ranged from about 30 to 42 percent. Ground-water flow and time-of-travel in the shallow aquifer system were simulated using the MODFLOW finite-difference model and the -particle-tracking program MODPATH. A three-layer, steady-state model of the shallow aquifer system was constructed and calibrated to the potentiometric surface of the A1 aquifer. Results of numerical modeling support the proposed conceptual hydrogeologic model of the shallow aquifer system. Ground-water time-of-travel in the A1 aquifer was simulated using an assumed effective porosity of 25 percent. Typical ground-water-flow velocities were on the or

Effect of the method of estimation of soil saturated hydraulic conductivity with regards to the design of stormwater infiltration trenches

NASA Astrophysics Data System (ADS)

Paiva coutinho, Artur; Predelus, Dieuseul; Lassabatere, Laurent; Ben Slimene, Erij; Celso Dantas Antonino, Antonio; Winiarski, Thierry; Joaquim da Silva Pereira Cabral, Jaime; Angulo-Jaramillo, Rafael

2014-05-01

Best management practices are based on the infiltration of stormwater (e.g. infiltration into basins or trenches) to reduce the risk of flooding of urban areas. Proper estimations of saturated hydraulic conductivity of the vadose zone are required to avoid inappropriate design of infiltration devices. This article aims at assessing (i) the method-dependency of the estimation of soils saturated hydraulic conductivity and (ii) the consequences of such dependency on the design of infiltration trenches. This is illustrated for the specific case of an infiltration trench to be constructed to receive stormwater from a specific parking surface, 250 m2 in area, in Recife (Brazil). Water infiltration experiments were conducted according to the Beerkan Method, i.e. application of a zero water pressure head through a disc source (D=15 cm) and measures of the amount of infiltrated water with time. Saturated hydraulic conductivity estimates are derived from the analysis of these infiltration tests using several different conceptual approaches: one-dimensional models of Horton(1933) and Philip(1957), three-dimensional methods recently developed (Lassabatere et al., 2006, Wu et al., 1999, and Bagarello et al., 2013) and direct 3-dimensional numerical inversion. The estimations for saturated hydraulic conductivity ranged between 65.5 mm/h and 94 mm/h for one-dimensional methods, whereas using three-dimensional methods saturated hydraulic conductivity ranged between 15.6 mm/h and 50 mm/h. These results shows the need for accounting for 3D geometry, and more generally, the physics of water infiltration in soils, if a proper characterization of soil saturated hydraulic conductivity is targeted. In a second step, each estimate of the saturated hydraulic conductivity was used to calculate the stormwater to be stored in the studied trench for several rainfall events of recurrence intervals of 2 to 25 years. The calculation of these volumes showed a great sensitivity with regards to the estimated values of saturated hydraulic conductivity. The designed volumes of the trench vary from 8.3 m3 to 15.9 m3 for one-dimensional methods and 11.9 m3 to 24.5 m3 for three-dimensional methods, respectively. The results show that any miss-estimation of the saturated hydraulic conductivity of soils may drastically impact the design of infiltration devices and the related extra-costs. Bagarello, B.; Castellini, M.; Di Prima,S.;Giordano ,G.; Iovino, M. (2013). Testing a simplified approach to determine field saturated soil hydraulic conductivity. Procedia Environmental Sciences 19 ( 2013 ) 599 - 608 Horton, R. (1933). The role of infiltration in the hydrologic cycle. American Geophysical Union Transactions 14, 446-460. Lassabatère, L.; Angulo-Jaramillo, R.; Soria, J.M.; Cuenca, R.; Braud, I.; Haverkamp, R.(2006). Beerkan estimation of soil transfer parameters through infiltration experiments - BEST. Soil Science Society of American Journal, Madison, v.70, p.521-532, 2006. Philip, J.R. (1957). The theory of Infiltration: 5. The Influence of the Initial Moisture Content. Soil Science, v.4, n.84, p.329-339, 1957. Wu, L.; Pan, L.; Mitchell, J.; Sanden, B. (1999). Measuring satured hydraulic conductivity using a generalized solution for single-ringle infiltrometers. Soil Sci.Soc.Am.J.63, 788-792

Conductance based characterization of structure and hopping site density in 2D molecule-nanoparticle arrays

NASA Astrophysics Data System (ADS)

McCold, Cliff E.; Fu, Qiang; Howe, Jane Y.; Hihath, Joshua

2015-09-01

Composite molecule-nanoparticle hybrid systems have recently emerged as important materials for applications ranging from chemical sensing to nanoscale electronics. However, creating reproducible and repeatable composite materials with precise properties has remained one of the primary challenges to the implementation of these technologies. Understanding the sources of variation that dominate the assembly and transport behavior is essential for the advancement of nanoparticle-array based devices. In this work, we use a combination of charge-transport measurements, electron microscopy, and optical characterization techniques to determine the role of morphology and structure on the charge transport properties of 2-dimensional monolayer arrays of molecularly-interlinked Au nanoparticles. Using these techniques we are able to determine the role of both assembly-dependent and particle-dependent defects on the conductivities of the films. These results demonstrate that assembly processes dominate the dispersion of conductance values, while nanoparticle and ligand features dictate the mean value of the conductance. By performing a systematic study of the conductance of these arrays as a function of nanoparticle size we are able to extract the carrier mobility for specific molecular ligands. We show that nanoparticle polydispersity correlates with the void density in the array, and that because of this correlation it is possible to accurately determine the void density within the array directly from conductance measurements. These results demonstrate that conductance-based measurements can be used to accurately and non-destructively determine the morphological and structural properties of these hybrid arrays, and thus provide a characterization platform that helps move 2-dimensional nanoparticle arrays toward robust and reproducible electronic systems.Composite molecule-nanoparticle hybrid systems have recently emerged as important materials for applications ranging from chemical sensing to nanoscale electronics. However, creating reproducible and repeatable composite materials with precise properties has remained one of the primary challenges to the implementation of these technologies. Understanding the sources of variation that dominate the assembly and transport behavior is essential for the advancement of nanoparticle-array based devices. In this work, we use a combination of charge-transport measurements, electron microscopy, and optical characterization techniques to determine the role of morphology and structure on the charge transport properties of 2-dimensional monolayer arrays of molecularly-interlinked Au nanoparticles. Using these techniques we are able to determine the role of both assembly-dependent and particle-dependent defects on the conductivities of the films. These results demonstrate that assembly processes dominate the dispersion of conductance values, while nanoparticle and ligand features dictate the mean value of the conductance. By performing a systematic study of the conductance of these arrays as a function of nanoparticle size we are able to extract the carrier mobility for specific molecular ligands. We show that nanoparticle polydispersity correlates with the void density in the array, and that because of this correlation it is possible to accurately determine the void density within the array directly from conductance measurements. These results demonstrate that conductance-based measurements can be used to accurately and non-destructively determine the morphological and structural properties of these hybrid arrays, and thus provide a characterization platform that helps move 2-dimensional nanoparticle arrays toward robust and reproducible electronic systems. Electronic supplementary information (ESI) available: Temperature dependent measurements, activation energies, particle size distributions, void density-polydispersity relation, and DLS data. See DOI: 10.1039/c5nr04460j

Molecular testing for Lynch syndrome in people with colorectal cancer: systematic reviews and economic evaluation.

PubMed

Snowsill, Tristan; Coelho, Helen; Huxley, Nicola; Jones-Hughes, Tracey; Briscoe, Simon; Frayling, Ian M; Hyde, Chris

2017-09-01

Inherited mutations in deoxyribonucleic acid (DNA) mismatch repair (MMR) genes lead to an increased risk of colorectal cancer (CRC), gynaecological cancers and other cancers, known as Lynch syndrome (LS). Risk-reducing interventions can be offered to individuals with known LS-causing mutations. The mutations can be identified by comprehensive testing of the MMR genes, but this would be prohibitively expensive in the general population. Tumour-based tests - microsatellite instability (MSI) and MMR immunohistochemistry (IHC) - are used in CRC patients to identify individuals at high risk of LS for genetic testing. MLH1 (MutL homologue 1) promoter methylation and BRAF V600E testing can be conducted on tumour material to rule out certain sporadic cancers. To investigate whether testing for LS in CRC patients using MSI or IHC (with or without MLH1 promoter methylation testing and BRAF V600E testing) is clinically effective (in terms of identifying Lynch syndrome and improving outcomes for patients) and represents a cost-effective use of NHS resources. Systematic reviews were conducted of the published literature on diagnostic test accuracy studies of MSI and/or IHC testing for LS, end-to-end studies of screening for LS in CRC patients and economic evaluations of screening for LS in CRC patients. A model-based economic evaluation was conducted to extrapolate long-term outcomes from the results of the diagnostic test accuracy review. The model was extended from a model previously developed by the authors. Ten studies were identified that evaluated the diagnostic test accuracy of MSI and/or IHC testing for identifying LS in CRC patients. For MSI testing, sensitivity ranged from 66.7% to 100.0% and specificity ranged from 61.1% to 92.5%. For IHC, sensitivity ranged from 80.8% to 100.0% and specificity ranged from 80.5% to 91.9%. When tumours showing low levels of MSI were treated as a positive result, the sensitivity of MSI testing increased but specificity fell. No end-to-end studies of screening for LS in CRC patients were identified. Nine economic evaluations of screening for LS in CRC were identified. None of the included studies fully matched the decision problem and hence a new economic evaluation was required. The base-case results in the economic evaluation suggest that screening for LS in CRC patients using IHC, BRAF V600E and MLH1 promoter methylation testing would be cost-effective at a threshold of £20,000 per quality-adjusted life-year (QALY). The incremental cost-effectiveness ratio for this strategy was £11,008 per QALY compared with no screening. Screening without tumour tests is not predicted to be cost-effective. Most of the diagnostic test accuracy studies identified were rated as having a risk of bias or were conducted in unrepresentative samples. There was no direct evidence that screening improves long-term outcomes. No probabilistic sensitivity analysis was conducted. Systematic review evidence suggests that MSI- and IHC-based testing can be used to identify LS in CRC patients, although there was heterogeneity in the methods used in the studies identified and the results of the studies. There was no high-quality empirical evidence that screening improves long-term outcomes and so an evidence linkage approach using modelling was necessary. Key determinants of whether or not screening is cost-effective are the accuracy of tumour-based tests, CRC risk without surveillance, the number of relatives identified for cascade testing, colonoscopic surveillance effectiveness and the acceptance of genetic testing. Future work should investigate screening for more causes of hereditary CRC and screening for LS in endometrial cancer patients. This study is registered as PROSPERO CRD42016033879. The National Institute for Health Research Health Technology Assessment programme.

Graphene/Poly(aniline-co-pyrrole) Nanocomposite: Potential Candidate for Supercapacitor and Microwave Absorbing Applications.

PubMed

Sahoo, Sumanta; Bhattacharya, Pallab; Dhibar, Saptarshi; Hatui, Goutam; Das, Tanya; Das, Chapal Kumar

2015-09-01

A simple and cost-effective in-situ chemical route to prepare the nanocomposites based on graphene and Poly(aniline-co-pyrrole) [PPP] has been proposed. Introduction of graphene changes the morphology of copolymer from spherical to fiber like. Graphene/Poly(aniline-co-pyrrole) [GPPP] nanocomposite achieved highest specific capacitance of 351 F/g and energy density of 124.8 Wh/Kg at 10 mV/s scan rate. The composite also obtained moderate specific capacitance retention of 66% after 500 cycles, which establish its potentiality as supercapacitor electrode materials. The composite also exhibited high electrical conductivity and superior microwave absorbing properties (maximum reflection loss is -29.97 dB). The absorption range corresponding to ≥ 90% absorption (or -10 dB) is 2.72 GHz which is excellent for the microwave absorbing applications.

Partitioning coefficients of polycyclic aromatic hydrocarbons in stack gas from a municipal incinerator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, W.M.G.; Chen, J.C.

1995-12-31

In this study, solid-gas partitioning coefficients of PAHs on fly ash in stack gas from a municipal incinerator were determined according to elution analysis with gas-solid chromatography. The fly ash from the electrostatic precipitator was sieved and packed into a 1/4 inch (6.3 mm) pyrex column. Elution analysis with gas-solid chromatography was conducted for three PAEs, Napthalene, Anthracene, and Pyrene. The temperature for elution analysis was in the range of 100{degrees}C to 300{degrees}C. Vg, specific retention volume obtained from elution analysis, and S, specific surface area of fly ash measured by a surface area measurement instrument were used to estimatemore » the solid-gas partitioning coefficient KR. In addition, the relationships between KR and temperature and KR and PAH concentrations were investigated.« less

Geographical Assessment of Rickettsioses in Indonesia.

PubMed

Widjaja, Susana; Williams, Maya; Winoto, Imelda; Farzeli, Arik; Stoops, Craig A; Barbara, Kathryn A; Richards, Allen L; Blair, Patrick J

2016-01-01

To expand the documentation of rickettsioses in Indonesia, we conducted an ectoparasite and small mammal investigation involving four major islands: Java, Sumatra, Sulawesi, and Kalimantan. Coastal and highland regions on each island surveyed were chosen to represent different ecologies in Indonesia. Indication of the presence of Rickettsia spp. was evident in all areas sampled. Typhus group rickettsiae-specific antibodies had significantly higher prevalence among small mammals captured in Java compared to the other islands surveyed (78% in coastal and 50% in highland regions) and the prevalence of spotted fever group rickettsiae-specific antibodies was significantly higher in Kalimantan than the other islands investigated. Hosts and vectors were restricted by Rickettsia spp. but not by coastal or highland regions. Our findings expand the range in which rickettsial pathogens have been documented within the Indonesian archipelago and point to a significant risk to human health.

Magnetoconductance signatures of subband structure in semiconductor nanowires

NASA Astrophysics Data System (ADS)

Holloway, Gregory; Haapamaki, Chris; Lapierre, Ray; Baugh, Jonathan

2015-03-01

Understanding the subband structure due to radial confinement in semiconductor nanowires can benefit technologies ranging from optical sensors to quantum information processing. An axial magnetic field couples to the orbital angular momentum, giving rise to non-trivial features in electronic transport as a function of magnetic field. Previous reports focused on conduction electrons confined to a thin shell near the nanowire surface, which lead to flux-periodic energies and conductance oscillations. Here, we calculate the eigenstates for more general radial potentials with moderate to low surface band bending such that electrons are distributed more uniformly across the nanowire cross-section. It is found that the energy spectrum becomes aperiodic in both gate voltage and magnetic field as the radial potential becomes flatter. The behavior of an energy level is dictated by its angular momentum, and this allows, in principle, each state to be identified based on its dependence on magnetic field and the chemical potential. We experimentally investigate a short-channel InAs nanowire FET in search of conductance features that reveal this subband structure. A quantitative measure for assigning conductance features to specific transverse states is introduced and applied to this device.

SimHap GUI: an intuitive graphical user interface for genetic association analysis.

PubMed

Carter, Kim W; McCaskie, Pamela A; Palmer, Lyle J

2008-12-25

Researchers wishing to conduct genetic association analysis involving single nucleotide polymorphisms (SNPs) or haplotypes are often confronted with the lack of user-friendly graphical analysis tools, requiring sophisticated statistical and informatics expertise to perform relatively straightforward tasks. Tools, such as the SimHap package for the R statistics language, provide the necessary statistical operations to conduct sophisticated genetic analysis, but lacks a graphical user interface that allows anyone but a professional statistician to effectively utilise the tool. We have developed SimHap GUI, a cross-platform integrated graphical analysis tool for conducting epidemiological, single SNP and haplotype-based association analysis. SimHap GUI features a novel workflow interface that guides the user through each logical step of the analysis process, making it accessible to both novice and advanced users. This tool provides a seamless interface to the SimHap R package, while providing enhanced functionality such as sophisticated data checking, automated data conversion, and real-time estimations of haplotype simulation progress. SimHap GUI provides a novel, easy-to-use, cross-platform solution for conducting a range of genetic and non-genetic association analyses. This provides a free alternative to commercial statistics packages that is specifically designed for genetic association analysis.

Partnership readiness for community-based participatory research

PubMed Central

Andrews, Jeannette O.; Newman, Susan D.; Meadows, Otha; Cox, Melissa J.; Bunting, Shelia

2012-01-01

The use of a dyadic lens to assess and leverage academic and community partners’ readiness to conduct community-based participatory research (CBPR) has not been systematically investigated. With a lack of readiness to conduct CBPR, the partnership and its products are vulnerable. The purpose of this qualitative study was to explore the dimensions and key indicators necessary for academic and community partnership readiness to conduct CBPR. Key informant interviews and focus groups (n = 36 participants) were conducted with academic and community participants who had experiences with CBPR partnerships. A ‘framework analysis' approach was used to analyze the data and generate a new model, CBPR Partnership Readiness Model. Antecedents of CBPR partnership readiness are a catalyst and mutual interest. The major dimensions of the CBPR Partnership Readiness Model are (i) goodness of fit, (ii) capacity, and (iii) operations. Preferred outcomes are sustainable partnership and product, mutual growth, policy and social and health impact on the community. CBPR partnership readiness is an iterative and dynamic process, partnership and issue specific, influenced by a range of environmental and contextual factors, amenable to change and essential for sustainability and promotion of health and social change in the community. PMID:20837654

Hydrogeologic characterization of a proposed landfill expansion in Pickens County near Easley, South Carolina

USGS Publications Warehouse

Stringfield, W.J.

1994-01-01

This report presents the results of a hydrogeologic study in the Piedmont physiographic province of South Carolina to obtain geologic, hydrologic, and water-quality data from the site of a proposed landfill expansion in Pickens County near Easley, South Carolina. The geology of the study area is typical of the Piedmont region. The unconsolidated regolith on the site is soil and saprolite, which is a product of the weathered parent rock. The soil ranges in thickness from about 5 to 20 feet. The saprolite ranges in thickness from about 5 to 134 feet. The most abundant parent rock type in the area is a biotite gneiss. Ground- and surface-water data were collected at the site. Slug tests on the saprolite indicate a mean hydraulic conductivity of 3 x 0.000003 feet per second. Transmissivity ranges from 12 to 27 cubic feet per day per feet (squared per day). The ground-water velocity for the site ranges from 3 to 6 feet per year. The closest major stream to the site is Golden Creek. Based on low-flow data for Golden Creek, the estimated minimum 7 consecutive day flow that has a recurrence interval of 10 years (7Q10) at station 02186102 is 2.4 cubic feet per second. Water samples were collected from five monitoring wells at the proposed landfill expansion site and from one stream adjacent to the expansion site. Measured pH units ranged from 5.5 to 8.1, and alkalinity concentrations ranged from 5.1 to 73 milligrams per liter as CaCO3. Other water- quality data obtained included temperature and specific conductance, and 5-day BOD (biochemical oxygen demand), bicarbonate, ammonia-nitrogen, nitrite-nitrogen, nitrite plus nitrate, organic carbon, calcium, magnesium, sodium, potassium, chloride, sulfate, fluoride, and selected trace metal concentrations.

Diagnostic reproducibility of hydatidiform moles: ancillary techniques (p57 immunohistochemistry and molecular genotyping) improve morphologic diagnosis.

PubMed

Vang, Russell; Gupta, Mamta; Wu, Lee-Shu-Fune; Yemelyanova, Anna V; Kurman, Robert J; Murphy, Kathleen M; Descipio, Cheryl; Ronnett, Brigitte M

2012-03-01

Distinction of hydatidiform moles (HMs) from nonmolar specimens (NMs) and subclassification of HMs as complete hydatidiform moles (CHMs) and partial hydatidiform moles (PHMs) are important for clinical practice and investigational studies; yet, diagnosis based solely on morphology is affected by interobserver variability. Molecular genotyping can distinguish these entities by discerning androgenetic diploidy, diandric triploidy, and biparental diploidy to diagnose CHMs, PHMs, and NMs, respectively. Eighty genotyped cases (27 CHMs, 27 PHMs, and 26 NMs) were selected from a series of 200 potentially molar specimens previously diagnosed using p57 immunostaining and genotyping. Cases were classified by 3 gynecologic pathologists on the basis of H&E slides (masked to p57 immunostaining and genotyping results) into 1 of 3 categories (CHM, PHM, or NM) during 2 diagnostic rounds; a third round incorporating p57 immunostaining results was also conducted. Consensus diagnoses (those rendered by 2 of 3 pathologists) were determined. Genotyping results were used as the gold standard for assessing diagnostic performance. Sensitivity of a diagnosis of CHM ranged from 59% to 100% for individual pathologists and from 70% to 81% by consensus; specificity ranged from 91% to 96% for individuals and from 94% to 98% by consensus. Sensitivity of a diagnosis of PHM ranged from 56% to 93% for individual pathologists and from 70% to 78% by consensus; specificity ranged from 58% to 92% for individuals and from 74% to 85% by consensus. The percentage of correct classification of all cases by morphology ranged from 55% to 75% for individual pathologists and from 70% to 75% by consensus. The κ values for interobserver agreement ranged from 0.59 to 0.73 (moderate to good) for a diagnosis of CHM, from 0.15 to 0.43 (poor to moderate) for PHM, and from 0.13 to 0.42 (poor to moderate) for NM. The κ values for intraobserver agreement ranged from 0.44 to 0.67 (moderate to good). Addition of the p57 immunostain improved sensitivity of a diagnosis of CHM to a range of 93% to 96% for individual pathologists and 96% by consensus; specificity was improved from a range of 96% to 98% for individual pathologists and 96% by consensus; there was no substantial impact on diagnosis of PHMs and NMs. Interobserver agreement for interpretation of the p57 immunostain was 0.96 (almost perfect). Even with morphologic assessment by gynecologic pathologists and p57 immunohistochemistry, 20% to 30% of cases will be misclassified, and, in particular, distinction of PHMs and NMs will remain problematic.

Influence of metallic vapours on thermodynamic and transport properties of two-temperature air plasma

NASA Astrophysics Data System (ADS)

Zhong, Linlin; Wang, Xiaohua; Cressault, Yann; Teulet, Philippe; Rong, Mingzhe

2016-09-01

The metallic vapours (i.e., copper, iron, and silver in this paper) resulting from walls and/or electrode surfaces can significantly affect the characteristics of air plasma. Different from the previous works assuming local thermodynamic equilibrium, this paper investigates the influence of metallic vapours on two-temperature (2 T) air plasma. The 2 T compositions of air contaminated by Cu, Fe, and Ag are first determined based on Saha's and Guldberg-Waage's laws. The thermodynamic properties (including mass density, specific enthalpy, and specific heat) are then calculated according to their definitions. After determining the collision integrals for each pair of species in air-metal mixtures using the newly published methods and source data, the transport coefficients (including electrical conductivity, viscosity, and thermal conductivity) are calculated for air-Cu, air-Fe, and air-Ag plasmas with different non-equilibrium degree θ (Te/Th). The influences of metallic contamination as well as non-equilibrium degree are discussed. It is found that copper, iron, and silver exist mainly in the form of Cu2, FeO, and AgO at low temperatures. Generally, the metallic vapours increase mass density at most temperatures, reduce the specific enthalpy and specific heat in the whole temperature range, and affect the transport properties remarkably from 5000 K to 20 000 K. The effect arising from the type of metals is little except for silver at certain temperatures. Besides, the departure from thermal equilibrium results in the delay of dissociation and ionization reactions, leading to the shift of thermodynamic and transport properties towards a higher temperature.

Surface-water-quality assessment of the Upper Illinois River basin in Illinois, Indiana, and Wisconsin; cross-sectional and depth variation of water-quality constituents and properties in the Upper Illinois River basin, 1987-88

USGS Publications Warehouse

Marron, Donna C.; Blanchard, Stephen F.

1995-01-01

Data on water velocity, temperature, specific con- ductance, pH, dissolved oxygen concentration, chlorophyll concentration, suspended sediment con- centration, fecal-coliform counts, and the percen- tage of suspended sediment finer than 62 micrometers ranged up to 21 percent; and cross-section coefficients of variation of the concentrations of suspended sediment, fecal coliform, and chlorophyll ranged from 7 to 115 percent. Midchannel measure- ments of temperature, specific conductance, and pH were within 5 percent of mean cross-sectional values of these properties at the eight sampling sites, most of which appear well mixed because of the effect of dams and reservoirs. Measurements of the concentration of dissolved oxygen at various cross- section locations and at variable sampling depths are required to obtain a representative value of this constituent at these sites. The large varia- bility of concentrations of chlorophyll and suspended sediment, and fecal-coliform counts at the eight sampling sites indicates that composite rather than midchannel or mean values of these constituents are likely to be most representative of the channel cross section.

The fabrication of a customized occlusal splint based on the merging of dynamic jaw tracking records, cone beam computed tomography, and CAD-CAM digital impression.

PubMed

Aslanidou, Katerina; Kau, Chung How; Vlachos, Christos; Saleh, Tayem Abou

2017-01-01

The aim of this case report was to present the procedure of fabricating a customized occlusal splint, through a revolutionary software that combines cone beam computed tomography (CBCT) with jaw motion tracking (JMT) data and superimposes a digital impression. The case report was conducted on a 46-year-old female patient diagnosed with the temporomandibular disorder. A CBCT scan and an optical impression were obtained. The range of the patient's mandibular movements was captured with a JMT device. The data were combined in the SICAT software (SICAT, Sirona, Bonn, Germany). The software enabled the visualization of patient-specific mandibular movements and provided a real dynamic anatomical evaluation of the condylar position in the glenoid fossa. After the assessment of the range of movements during opening, protrusion, and lateral movements all the data were sent to SICAT and a customized occlusal splint was manufactured. The SICAT software provides a three-dimensional real-dynamic simulation of mandibular movements relative to the patient-specific anatomy of the jaw; thus, it opens new possibilities and potentials for the management of temporomandibular disorders.

Wave Pattern Peculiarities of Different Types of Explosions Conducted at Semipalatinsk Test Site

NASA Astrophysics Data System (ADS)

Sokolova, Inna

2014-05-01

The historical seismograms of the explosions conducted at the STS in 1949 - 1989 are of great interest for the researchers in the field of monitoring. Large number of air (86), surface (30) and underground nuclear explosions were conducted here in boreholes and tunnels (340). In addition to nuclear explosions, large chemical explosions were conducted at the Test Site. It is known that tectonic earthquakes occur on the Test Site territory and near it. Since 2005 the Institute of Geophysical Researches conducts works on digitizing the historical seismograms of nuclear explosions. Currently, the database contains more than 6000 digitized seismograms of nuclear explosions used for investigative monitoring tasks, major part of them (4000) are events from the STS region. Dynamic parameters of records of air, surface and underground nuclear explosions, as well as large chemical explosions with compact charge laying were investigated for seismic stations located on the territory of Kazakhstan using digitized records of the STS events. In addition, the comparison between salvo wave pattern and single explosions was conducted. The records of permanent and temporary seismic stations (epicentral distances range 100 - 800 km) were used for the investigations. Explosions spectra were analyzed, specific features of each class of events were found. The seismograms analysis shows that the wave pattern depends significantly on the explosion site and on the source type.

Review paper: progress in the field of conducting polymers for tissue engineering applications.

PubMed

Bendrea, Anca-Dana; Cianga, Luminita; Cianga, Ioan

2011-07-01

This review focuses on one of the most exciting applications area of conjugated conducting polymers, which is tissue engineering. Strategies used for the biocompatibility improvement of this class of polymers (including biomolecules' entrapment or covalent grafting) and also the integrated novel technologies for smart scaffolds generation such as micropatterning, electrospinning, self-assembling are emphasized. These processing alternatives afford the electroconducting polymers nanostructures, the most appropriate forms of the materials that closely mimic the critical features of the natural extracellular matrix. Due to their capability to electronically control a range of physical and chemical properties, conducting polymers such as polyaniline, polypyrrole, and polythiophene and/or their derivatives and composites provide compatible substrates which promote cell growth, adhesion, and proliferation at the polymer-tissue interface through electrical stimulation. The activities of different types of cells on these materials are also presented in detail. Specific cell responses depend on polymers surface characteristics like roughness, surface free energy, topography, chemistry, charge, and other properties as electrical conductivity or mechanical actuation, which depend on the employed synthesis conditions. The biological functions of cells can be dramatically enhanced by biomaterials with controlled organizations at the nanometer scale and in the case of conducting polymers, by the electrical stimulation. The advantages of using biocompatible nanostructures of conducting polymers (nanofibers, nanotubes, nanoparticles, and nanofilaments) in tissue engineering are also highlighted.

Anxiety levels in mothers of children with specific learning disability.

PubMed

Karande, S; Kumbhare, N; Kulkarni, M; Shah, N

2009-01-01

Parents of children with specific learning disability (SpLD) undergo stress in coping with their child's condition. To measure the levels of anxiety and find out the cause of anxiety in mothers of children with SpLD at time of diagnosis. Prospective rating-scale and interview-based study conducted in our clinic. One hundred mothers of children (70 boys, 30 girls) with SpLD were interviewed using the Hamilton anxiety rating scale (HAM-A) and a semi-structured questionnaire. Detailed clinical and demographic data of mothers were noted. Chi-square test or unpaired student's t-test was applied wherever applicable. The mean age of mothers was 40.14 years (+/-SD 4.94, range 25.07-54.0), 73% belonged to upper or upper middle socioeconomic strata of society, 67% were graduates or postgraduates, 58% were full-time home-makers, and 33% lived in joint families. Levels of anxiety were absent in 24%, mild in 75%, and moderate in 1% of mothers. Their mean total anxiety score was 5.65 (+/-SD 4.75, range 0-21), mean psychic anxiety score was 3.92 (+/-SD 3.11, range 0-13), and mean somatic anxiety score was 1.76 (+/-SD 2.05, range 0-10). Their common worries were related to child's poor school performance (95%), child's future (90%), child's behavior (51%), and visits to our clinic (31%). Most mothers of children with SpLD have already developed mild anxiety levels by the time this hidden disability is diagnosed. These anxieties should be addressed by counseling to ensure optimum rehabilitation of these children.

Use of Visual Range Measurements to Predict PM2.5 Exposures in Southwest Asia and Afghanistan

PubMed Central

Masri, Shahir; Garshick, Eric; Hart, Jaime; Bouhamra, Walid; Koutrakis, Petros

2016-01-01

Military personnel deployed to Southwest Asia and Afghanistan were exposed to high levels of ambient particulate matter (PM) indicating the potential for exposure-related health effects. However, historical quantitative ambient PM exposure data for conducting epidemiological health studies are unavailable due to a lack of monitoring stations. Since visual range is proportional to particle light extinction (scattering and absorption), visibility can serve as a surrogate for PM2.5 concentrations where ground measurements are not available. We used data on visibility, relative humidity (RH), and PM2.5 ground measurements collected in Kuwait from years 2004 to 2005 to establish the relationship between PM2.5 and visibility. Model validation obtained by regressing trimester average PM2.5 predictions against PM2.5 measurements in Kuwait produced an r2 value of 0.84. Cross validation of urban and rural sites in Kuwait also revealed good model fit. We applied this relationship to location-specific visibility data at 104 regional sites between years 2000 and 2012 to estimate monthly average PM2.5 concentrations. Monthly averages at sites in Iraq, Afghanistan, United Arab Emirates, Kuwait, Djibouti, and Qatar ranged from 10 to 365 µg/m3 during this period, while site averages ranged from 22 to 80 µg/m3, indicating considerable spatial and temporal heterogeneity in ambient PM2.5 across these regions. These data support the use of historical visibility data to estimate location-specific PM2.5 concentrations for use in future epidemiological studies in the region. PMID:27700621

Comparing diagnostic accuracy of bedside ultrasound and radiography for bone fracture screening in multiple trauma patients at the ED.

PubMed

Bolandparvaz, Shahram; Moharamzadeh, Payman; Jamali, Kazem; Pouraghaei, Mahboob; Fadaie, Maryam; Sefidbakht, Sepideh; Shahsavari, Kavous

2013-11-01

Long bone fractures are currently diagnosed using radiography, but radiography has some disadvantages (radiation and being time consuming). The present study compared the diagnostic accuracy of bedside ultrasound and radiography in multiple trauma patients at the emergency department (ED). The study assessed 80 injured patients with multiple trauma from February 2011 to July 2012. The patients were older than 18 years and triaged to the cardiopulmonary resuscitation ward of the ED. Bedside ultrasound and radiography were conducted for them. The findings were separately and blindly assessed by 2 radiologists. Sensitivity, specificity, the positive and negative predictive value, and κ coefficient were measured to assess the accuracy and validity of ultrasound as compared with radiography. The sensitivity of ultrasound for diagnosis of limb bone fractures was not high enough and ranged between 55% and 75% depending on the fracture site. The specificity of this diagnostic method had an acceptable range of 62% to 84%. Ultrasound negative prediction value was higher than other indices under study and ranged between 73% and 83%, but its positive prediction value varied between 33.3% and 71%. The κ coefficient for diagnosis of long bone fractures of upper limb (κ = 0.58) and upper limb joints (κ = 0.47) and long bones of lower limb (κ = 0.52) was within the medium range. However, the value for diagnosing fractures of lower limb joints (κ = 0.47) was relatively low. Bedside ultrasound is not a reliable method for diagnosing fractures of upper and lower limb bones compared with radiography. © 2013 Elsevier Inc. All rights reserved.

The Relationship Between Population-Level Exposure to Alcohol Advertising on Television and Brand-Specific Consumption Among Underage Youth in the US

PubMed Central

Ross, Craig S.; Maple, Emily; Siegel, Michael; DeJong, William; Naimi, Timothy S.; Padon, Alisa A.; Borzekowski, Dina L.G.; Jernigan, David H.

2015-01-01

Aims: We investigated the population-level relationship between exposure to brand-specific advertising and brand-specific alcohol use among US youth. Methods: We conducted an internet survey of a national sample of 1031 youth, ages 13–20, who had consumed alcohol in the past 30 days. We ascertained all of the alcohol brands respondents consumed in the past 30 days, as well as which of 20 popular television shows they had viewed during that time period. Using a negative binomial regression model, we examined the relationship between aggregated brand-specific exposure to alcohol advertising on the 20 television shows [ad stock, measured in gross rating points (GRPs)] and youth brand-consumption prevalence, while controlling for the average price and overall market share of each brand. Results: Brands with advertising exposure on the 20 television shows had a consumption prevalence about four times higher than brands not advertising on those shows. Brand-level advertising elasticity of demand varied by exposure level, with higher elasticity in the lower exposure range. The estimated advertising elasticity of 0.63 in the lower exposure range indicates that for each 1% increase in advertising exposure, a brand's youth consumption prevalence increases by 0.63%. Conclusions: At the population level, underage youths' exposure to brand-specific advertising was a significant predictor of the consumption prevalence of that brand, independent of each brand's price and overall market share. The non-linearity of the observed relationship suggests that youth advertising exposure may need to be lowered substantially in order to decrease consumption of the most heavily advertised brands. PMID:25754127

The relationship between population-level exposure to alcohol advertising on television and brand-specific consumption among underage youth in the US.

PubMed

Ross, Craig S; Maple, Emily; Siegel, Michael; DeJong, William; Naimi, Timothy S; Padon, Alisa A; Borzekowski, Dina L G; Jernigan, David H

2015-05-01

We investigated the population-level relationship between exposure to brand-specific advertising and brand-specific alcohol use among US youth. We conducted an internet survey of a national sample of 1031 youth, ages 13-20, who had consumed alcohol in the past 30 days. We ascertained all of the alcohol brands respondents consumed in the past 30 days, as well as which of 20 popular television shows they had viewed during that time period. Using a negative binomial regression model, we examined the relationship between aggregated brand-specific exposure to alcohol advertising on the 20 television shows [ad stock, measured in gross rating points (GRPs)] and youth brand-consumption prevalence, while controlling for the average price and overall market share of each brand. Brands with advertising exposure on the 20 television shows had a consumption prevalence about four times higher than brands not advertising on those shows. Brand-level advertising elasticity of demand varied by exposure level, with higher elasticity in the lower exposure range. The estimated advertising elasticity of 0.63 in the lower exposure range indicates that for each 1% increase in advertising exposure, a brand's youth consumption prevalence increases by 0.63%. At the population level, underage youths' exposure to brand-specific advertising was a significant predictor of the consumption prevalence of that brand, independent of each brand's price and overall market share. The non-linearity of the observed relationship suggests that youth advertising exposure may need to be lowered substantially in order to decrease consumption of the most heavily advertised brands. © The Author 2015. Medical Council on Alcohol and Oxford University Press. All rights reserved.

Specialist Insect Herbivore and Light Availability Do Not Interact in the Evolution of an Invasive Plant

PubMed Central

Zhang, Ziyan; He, Kate S.; Li, Bo

2015-01-01

Release from specialist insect herbivores may allow invasive plants to evolve traits associated with decreased resistance and increased competitive ability. Given that there may be genetic trade-off between resistance and tolerance, invasive plants could also become more tolerant to herbivores. Although it is widely acknowledged that light availability affects tolerance to herbivores, little information is available for whether the effect of light availability on tolerance differ between the introduced and native populations. We conducted a common garden experiment in the introduced range of Alternanthera philoxeroides using ten invasive US and ten native Argentinean populations at two levels of light availability and in the presence or absence of a specialist stem-boring insect Agasicles hygrophila. Plant biomass (total and storage root biomass), two allocation traits (root/shoot ratio and branch intensity, branches biomass/main stem biomass) and two functional traits (specific stem length and specific leaf area), which are potentially associated with herbivore resistance and light capture, were measured. Overall, we found that A. philoxeroides from introduced ranges had comparable biomass and tolerance to specialist herbivores, lower branch intensity, lower specific stem length and specific leaf area. Moreover, introduced populations displayed higher shade tolerance of storage root biomass and lower plastic response to shading in specific stem length. Finally, light availability had no significant effect on evolution of tolerance to specialist herbivores of A. philoxeroides. Our results suggest that post-introduction evolution might have occurred in A. philoxeroides. While light availability did not influence the evolution of tolerance to specialist herbivores, increased shade tolerance and release from specialist insects might have contributed to the successful invasion of A. philoxeroides. PMID:26407176