Test chamber for alpha spectrometry

DOEpatents

Larsen, Robert P.

1977-01-01

Alpha emitters for low-level radiochemical analysis by measurement of alpha spectra are positioned precisely with respect to the location of a surface-barrier detector by means of a chamber having a removable threaded planchet holder. A pedestal on the planchet holder holds a specimen in fixed engagement close to the detector. Insertion of the planchet holder establishes an O-ring seal that permits the chamber to be pumped to a desired vacuum. The detector is protected against accidental contact and resulting damage.

A cylindrical specimen holder for electron cryo-tomography.

PubMed

Palmer, Colin M; Löwe, Jan

2014-02-01

The use of slab-like flat specimens for electron cryo-tomography restricts the range of viewing angles that can be used. This leads to the "missing wedge" problem, which causes artefacts and anisotropic resolution in reconstructed tomograms. Cylindrical specimens provide a way to eliminate the problem, since they allow imaging from a full range of viewing angles around the tilt axis. Such specimens have been used before for tomography of radiation-insensitive samples at room temperature, but never for frozen-hydrated specimens. Here, we demonstrate the use of thin-walled carbon tubes as specimen holders, allowing the preparation of cylindrical frozen-hydrated samples of ribosomes, liposomes and whole bacterial cells. Images acquired from these cylinders have equal quality at all viewing angles, and the accessible tilt range is restricted only by the physical limits of the microscope. Tomographic reconstructions of these specimens demonstrate that the effects of the missing wedge are substantially reduced, and could be completely eliminated if a full tilt range was used. The overall quality of these tomograms is still lower than that obtained by existing methods, but improvements are likely in future. © 2013 The Authors. Published by Elsevier B.V. All rights reserved.

Effects of specimen preparation on the electromagnetic property measurements of solid materials with an automatic network analyzer

NASA Technical Reports Server (NTRS)

Long, E. R., Jr.

1986-01-01

Effects of specimen preparation on measured values of an acrylic's electomagnetic properties at X-band microwave frequencies, TE sub 1,0 mode, utilizing an automatic network analyzer have been studied. For 1 percent or less error, a gap between the specimen edge and the 0.901-in. wall of the specimen holder was the most significant parameter. The gap had to be less than 0.002 in. The thickness variation and alignment errors in the direction parallel to the 0.901-in. wall were equally second most significant and had to be less than 1 degree. Errors in the measurement f the thickness were third most significant. They had to be less than 3 percent. The following parameters caused errors of 1 percent or less: ratios of specimen-holder thicknesses of more than 15 percent, gaps between the specimen edge and the 0.401-in. wall less than 0.045 in., position errors less than 15 percent, surface roughness, hickness variation in the direction parallel to the 0.401-in. wall less than 35 percent, and specimen alignment in the direction parallel to the 0.401-in. wall mass than 5 degrees.

Effect of Boundary Condition on the Shear Behaviour of Rock Joints in the Direct Shear Test

NASA Astrophysics Data System (ADS)

Bahaaddini, M.

2017-05-01

The common method for determination of the mechanical properties of the rock joints is the direct shear test. This paper aims to study the effect of boundary condition on the results of direct shear tests. Experimental studies undertaken in this research showed that the peak shear strength is mostly overestimated. This problem is more pronounced for steep asperities and under high normal stresses. Investigation of the failure mode of these samples showed that tensile cracks are generated at the boundary of sample close to the specimen holders and propagated inside the intact materials. In order to discover the reason of observed failure mechanism in experiments, the direct shear test was simulated using PFC2D. Results of numerical models showed that the gap zone size between the upper and lower specimen holders has a significant effect on the shear mechanism. For the high gap size, stresses concentrate at the vicinity of the tips of specimen holders and result in generation and propagation of tensile cracks inside the intact material. However, by reducing the gap size, stresses are concentrated on asperities, and damage of specimen at its boundary is not observed. Results of this paper show that understanding the shear mechanism of rock joints is an essential step prior to interpreting the results of direct shear tests.

A SIMPLE TUMBLING DEVICE USED IN PREPARING ALGAL SPECIMENS FOR ELECTRON MICROSCOPY.

PubMed

Berlagnolli, B L; Nadakavukaren, M J

1969-06-01

Screw cap vials are held in a wooden holder which rotates at a 90° angle to the horizontal. The. shaft of a small electric motor with built-in gear box is attached perpendicularly to the wooden vial holder via a hole drilled in the center of the wooden holder. The rotation of the vial holder is about 6 rpm. This motion ensures a thorough tumbling of the contents of the vials. Even viscous embedding media are kept in constant agitation, which provides for superior penetration of the tissue. Tumbling devices to hold a range of vial sizes can be constructed with a minimum of labor at a cost of $10-20 each.

16 CFR § 1611.4 - Flammability test.

Code of Federal Regulations, 2013 CFR

2013-01-01

... wrinkles. Five specimens from each direction (machine and transverse) of a given material shall be tested... D618, Tentative Methods of Conditioning Plastics and Electrical Insulating Materials for Testing. (c... flame. The sample shall be free from wrinkles or distortion when the holder is closed. The specimen...

16 CFR 1611.4 - Flammability test.

Code of Federal Regulations, 2011 CFR

2011-01-01

...) Test specimens shall be 3 in. in width and 9 in. in length. They shall be free from folds or wrinkles..., Tentative Methods of Conditioning Plastics and Electrical Insulating Materials for Testing. (c) Procedure... flame. The sample shall be free from wrinkles or distortion when the holder is closed. The specimen...

16 CFR 1611.4 - Flammability test.

Code of Federal Regulations, 2014 CFR

2014-01-01

...) Test specimens shall be 3 in. in width and 9 in. in length. They shall be free from folds or wrinkles..., Tentative Methods of Conditioning Plastics and Electrical Insulating Materials for Testing. (c) Procedure... flame. The sample shall be free from wrinkles or distortion when the holder is closed. The specimen...

An inexpensive approach for bright-field and dark-field imaging by scanning transmission electron microscopy in scanning electron microscopy.

PubMed

Patel, Binay; Watanabe, Masashi

2014-02-01

Scanning transmission electron microscopy in scanning electron microscopy (STEM-in-SEM) is a convenient technique for soft materials characterization. Various specimen-holder geometries and detector arrangements have been used for bright-field (BF) STEM-in-SEM imaging. In this study, to further the characterization potential of STEM-IN-SEM, a new specimen holder has been developed to facilitate direct detection of BF signals and indirect detection of dark-field (DF) signals without the need for substantial instrument modification. DF imaging is conducted with the use of a gold (Au)-coated copper (Cu) plate attached to the specimen holder which directs highly scattered transmitted electrons to an off-axis yttrium-aluminum-garnet (YAG) detector. A hole in the copper plate allows for BF imaging with a transmission electron (TE) detector. The inclusion of an Au-coated Cu plate enhanced DF signal intensity. Experiments validating the acquisition of true DF signals revealed that atomic number (Z) contrast may be achieved for materials with large lattice spacing. However, materials with small lattice spacing still exhibit diffraction contrast effects in this approach. The calculated theoretical fine probe size is 1.8 nm. At 30 kV, in this indirect approach, DF spatial resolution is limited to 3.2 nm as confirmed experimentally.

16 CFR § 1616.5 - Test procedure.

Code of Federal Regulations, 2013 CFR

2013-01-01

... specimen holder to be used in this test method is detailed in Engineering Drawing Number 7. It is designed... hooks and weights shall be used to produce a series of loads for char length determinations. Suitable.... Shorter conditioning times may be used if the change in weight of a specimen in successive weighings made...

16 CFR 1616.5 - Test procedure.

Code of Federal Regulations, 2011 CFR

2011-01-01

... specimen holder to be used in this test method is detailed in Engineering Drawing Number 7. It is designed... hooks and weights shall be used to produce a series of loads for char length determinations. Suitable.... Shorter conditioning times may be used if the change in weight of a specimen in successive weighings made...

16 CFR 1616.5 - Test procedure.

Code of Federal Regulations, 2012 CFR

2012-01-01

... specimen holder to be used in this test method is detailed in Engineering Drawing Number 7. It is designed... hooks and weights shall be used to produce a series of loads for char length determinations. Suitable.... Shorter conditioning times may be used if the change in weight of a specimen in successive weighings made...

16 CFR 1616.5 - Test procedure.

Code of Federal Regulations, 2010 CFR

2010-01-01

... specimen holder to be used in this test method is detailed in Engineering Drawing Number 7. It is designed... hooks and weights shall be used to produce a series of loads for char length determinations. Suitable.... Shorter conditioning times may be used if the change in weight of a specimen in successive weighings made...

16 CFR 1616.5 - Test procedure.

Code of Federal Regulations, 2014 CFR

2014-01-01

... specimen holder to be used in this test method is detailed in Engineering Drawing Number 7. It is designed... hooks and weights shall be used to produce a series of loads for char length determinations. Suitable.... Shorter conditioning times may be used if the change in weight of a specimen in successive weighings made...

30 CFR 7.406 - Flame test apparatus.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Cable Splice Kits § 7.406 Flame test apparatus. The principal parts of the apparatus used to test for... extend to the sample end location. These are used to energize the electric cable and splice specimens. They are not used, but may stay in place, when testing signaling cables. (b) Specimen holder (support...

30 CFR 7.406 - Flame test apparatus.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Cable Splice Kits § 7.406 Flame test apparatus. The principal parts of the apparatus used to test for... extend to the sample end location. These are used to energize the electric cable and splice specimens. They are not used, but may stay in place, when testing signaling cables. (b) Specimen holder (support...

30 CFR 7.406 - Flame test apparatus.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Cable Splice Kits § 7.406 Flame test apparatus. The principal parts of the apparatus used to test for... extend to the sample end location. These are used to energize the electric cable and splice specimens. They are not used, but may stay in place, when testing signaling cables. (b) Specimen holder (support...

Off-axis electron holography of bacterial cells and magnetic nanoparticles in liquid

DOE Office of Scientific and Technical Information (OSTI.GOV)

Prozorov, Tanya; Almeida, Trevor P.; Kovacs, Andras

Here, the mapping of electrostatic potentials and magnetic fields in liquids using electron holography has been considered to be unrealistic. Here, we show that hydrated cells of Magnetospirillum magneticum strain AMB-1 and assemblies of magnetic nanoparticles can be studied using off-axis electron holography in a fluid cell specimen holder within the transmission electron microscope. Considering that the holographic object and reference wave both pass through liquid, the recorded electron holograms show sufficient interference fringe contrast to permit reconstruction of the phase shift of the electron wave and mapping of the magnetic induction from bacterial magnetite nanocrystals. We assess the challengesmore » of performing in situ magnetization reversal experiments using a fluid cell specimen holder, discuss approaches for improving spatial resolution and specimen stability, and outline future perspectives for studying scientific phenomena, ranging from interparticle interactions in liquids and electrical double layers at solid–liquid interfaces to biomineralization and the mapping of electrostatic potentials associated with protein aggregation and folding.« less

Off-axis electron holography of bacterial cells and magnetic nanoparticles in liquid

DOE PAGES

Prozorov, Tanya; Almeida, Trevor P.; Kovacs, Andras; ...

2017-10-02

Here, the mapping of electrostatic potentials and magnetic fields in liquids using electron holography has been considered to be unrealistic. Here, we show that hydrated cells of Magnetospirillum magneticum strain AMB-1 and assemblies of magnetic nanoparticles can be studied using off-axis electron holography in a fluid cell specimen holder within the transmission electron microscope. Considering that the holographic object and reference wave both pass through liquid, the recorded electron holograms show sufficient interference fringe contrast to permit reconstruction of the phase shift of the electron wave and mapping of the magnetic induction from bacterial magnetite nanocrystals. We assess the challengesmore » of performing in situ magnetization reversal experiments using a fluid cell specimen holder, discuss approaches for improving spatial resolution and specimen stability, and outline future perspectives for studying scientific phenomena, ranging from interparticle interactions in liquids and electrical double layers at solid–liquid interfaces to biomineralization and the mapping of electrostatic potentials associated with protein aggregation and folding.« less

Hot tube method for the measuring of thermophysical properties of materials

NASA Astrophysics Data System (ADS)

Dieška, Peter; Boháč, Vlastimil; Vretenár, Viliam

2017-07-01

The measurement of thermal properties of materials that do not keep the form is problematic, because usually, the basic condition of the most models predicts constant dimensions. The plastic materials like clay or loam in natural condition always contain some water and thus are viscous and squeeze out of specimen holder when clamped even at weak force produced by specimen holder. Thus, the specimen dimensions are changing in during the measurement when it is not placed in a solid container. Even at this arrangement the shrinkage of material at the measurements causes the lowering the specimen thickness when using two probe method like pulse transient technique. This effect problem could be lowered or neglected at single probe techniques like the planar hot disk or this newly derived hot tube method. Hot tube method is derived for the probe made as the rectangular plane bended around the solid cylinder or tube made of thermally low conducting material. The probe generates the heat and the rate of temperature rise in it is driven by heat transfer ability of the measured surrounding material. Such a probe should be used in laboratory as well as in the field conditions.

Ultra high vacuum heating and rotating specimen stage

DOEpatents

Coombs, III, Arthur W.

1995-01-01

A heating and rotating specimen stage provides for simultaneous specimen heating and rotating. The stage is ideally suited for operation in ultrahigh vacuum (1.times.10.sup.-9 torr or less), but is useful at atmosphere and in pressurized systems as well. A specimen is placed on a specimen holder that is attached to a heater that, in turn, is attached to a top housing. The top housing is rotated relative to a bottom housing and electrically connected thereto by electrically conductive brushes. This stage is made of materials that are compatible with UHV, able to withstand high temperatures, possess low outgassing rates, are gall and seize resistant, and are able to carry substantial electrical loading without overheating.

High pressure reaction cell and transfer mechanism for ultrahigh vacuum spectroscopic chambers

NASA Astrophysics Data System (ADS)

Nelson, A. E.; Schulz, K. H.

2000-06-01

A novel high pressure reaction cell and sample transfer mechanism for ultrahigh vacuum (UHV) spectroscopic chambers is described. The design employs a unique modification of a commercial load-lock transfer system to emulate a tractable microreactor. The reaction cell has an operating pressure range of <1×10-4 to 1000 Torr and can be evacuated to UHV conditions to enable sample transfer into the spectroscopic chamber. Additionally, a newly designed sample holder equipped with electrical and thermocouple contacts is described. The sample holder is capable of resistive specimen heating to 400 and 800 °C with current requirements of 14 A (2 V) and 25 A (3.5 V), respectively. The design enables thorough material science characterization of catalytic reactions and the surface chemistry of catalytic materials without exposing the specimen to atmospheric contaminants. The system is constructed primarily from readily available commercial equipment allowing its rapid implementation into existing laboratories.

Laser Plasma Soft X-ray Microscope with Wolter Mirrors for Observation of Biological Specimens in Air

NASA Astrophysics Data System (ADS)

Hoshino, Masato; Aoki, Sadao

2006-02-01

A laser plasma soft X-ray microscope with Wolter mirrors was developed so that specimens could be set in the atmosphere. Silicon nitride membranes 100 nm thick were used as vacuum-tight windows. Using relatively large windows (0.46× 0.46 mm2), an adequate working distance for samples, which was approximately 1.2 mm, was assured. The endurance of the vacuum-tight window was measured briefly. Dry biological cells could be observed with resolution better than 100 nm. A preliminary observation of wet biological cells was carried out using a wet environmental sample holder which was composed of only two sheets of silicon nitride membrane. An X-ray micrograph of wet red blood cells from a chicken was obtained without apparent effects of radiation damage. The properties of a vacuum-tight window and a wet sample holder are discussed.

Apparatus for X-ray diffraction microscopy and tomography of cryo specimens

DOE PAGES

Beetz, T.; Howells, M. R.; Jacobsen, C.; ...

2005-03-14

An apparatus for diffraction microscopy of biological and materials science specimens is described. In this system, a coherent soft X-ray beam is selected with a pinhole, and the illuminated specimen is followed by an adjustable beamstop and CCD camera to record diffraction data from non-crystalline specimens. In addition, a Fresnel zone plate can be inserted to allow for direct imaging. The system makes use of a cryogenic specimen holder with cryotransfer capabilities to allow frozen hydrated specimens to be loaded. The specimen can be tilted over a range of ± 80 ° degrees for three-dimensional imaging; this is done bymore » computer-controlled motors, enabling automated alignment of the specimen through a tilt series. The system is now in use for experiments in soft X-ray diffraction microscopy.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ogura, Toshihiko, E-mail: t-ogura@aist.go.jp

Highlights: • We developed a high-sensitive frequency transmission electric-field (FTE) system. • The output signal was highly enhanced by applying voltage to a metal layer on SiN. • The spatial resolution of new FTE method is 41 nm. • New FTE system enables observation of the intact bacteria and virus in water. - Abstract: The high-resolution structural analysis of biological specimens by scanning electron microscopy (SEM) presents several advantages. Until now, wet bacterial specimens have been examined using atmospheric sample holders. However, images of unstained specimens in water using these holders exhibit very poor contrast and heavy radiation damage. Recently,more » we developed the frequency transmission electric-field (FTE) method, which facilitates the SEM observation of biological specimens in water without radiation damage. However, the signal detection system presents low sensitivity. Therefore, a high EB current is required to generate clear images, and thus reducing spatial resolution and inducing thermal damage to the samples. Here a high-sensitivity detection system is developed for the FTE method, which enhances the output signal amplitude by hundredfold. The detection signal was highly enhanced when voltage was applied to the metal layer on silicon nitride thin film. This enhancement reduced the EB current and improved the spatial resolution as well as the signal-to-noise ratio. The spatial resolution of a high-sensitive FTE system is 41 nm, which is considerably higher than previous FTE system. New FTE system can easily be utilised to examine various unstained biological specimens in water, such as living bacteria and viruses.« less

Ultra high vacuum heating and rotating specimen stage

DOEpatents

Coombs, A.W. III

1995-05-02

A heating and rotating specimen stage provides for simultaneous specimen heating and rotating. The stage is ideally suited for operation in ultrahigh vacuum (1{times}10{sup {minus}9} torr or less), but is useful at atmosphere and in pressurized systems as well. A specimen is placed on a specimen holder that is attached to a heater that, in turn, is attached to a top housing. The top housing is rotated relative to a bottom housing and electrically connected thereto by electrically conductive brushes. This stage is made of materials that are compatible with UHV, able to withstand high temperatures, possess low outgassing rates, are gall and seize resistant, and are able to carry substantial electrical loading without overheating. 5 figs.

Beam deceleration for block-face scanning electron microscopy of embedded biological tissue.

PubMed

Ohta, Keisuke; Sadayama, Shoji; Togo, Akinobu; Higashi, Ryuhei; Tanoue, Ryuichiro; Nakamura, Kei-ichiro

2012-04-01

The beam deceleration (BD) method for scanning electron microscopes (SEM) also referred to as "retarding" was applied to back-scattered electron (BSE) imaging of the flat block face of a resin embedded biological specimen under low accelerating voltage and low beam current conditions. BSE imaging was performed with 0-4 kV of BD on en bloc stained rat hepatocyte. BD drastically enhanced the compositional contrast of the specimen and also improved the resolution at low landing energy levels (1.5-3 keV) and a low beam current (10 pA). These effects also functioned in long working distance observation, however, stage tilting caused uncorrectable astigmatism in BD observation. Stage tilting is mechanically required for a FIB/SEM, so we designed a novel specimen holder to minimize the unfavorable tilting effect. The FIB/SEM 3D reconstruction using the new holder showed a reasonable contrast and resolution high enough to analyze individual cell organelles and also the mitochondrial cristae structures (~5 nm) of the hepatocyte. These results indicate the advantages of BD for block face imaging of biological materials such as cells and tissues under low-voltage and low beam current conditions. Copyright © 2011 Elsevier Ltd. All rights reserved.

Control of brushing variables for the in vitro assessment of toothpaste abrasivity using a novel laboratory model.

PubMed

Parry, Jason; Harrington, Edward; Rees, Gareth D; McNab, Rod; Smith, Anthony J

2008-02-01

Design and construct a tooth-brushing simulator incorporating control of brushing variables including brushing force, speed and temperature, thereby facilitating greater understanding of their importance in toothpaste abrasion testing methodologies. A thermostable orbital shaker was selected as a base unit and 16- and 24-specimen brushing rigs were constructed to fit inside, consisting of: a square bath partitioned horizontally to provide brushing channels, specimen holders for 25 mm diameter mounted specimens to fit the brushing channels and individually weighted brushing arms, able to support four toothbrush holders suspended over the brushing channels. Brush head holders consisted of individually weighted blocks of Delrin, or PTFE onto which toothbrush heads were fixed. Investigating effects of key design criteria involved measuring abrasion depths of polished human enamel and dentine. The brushing simulator demonstrated good reproducibility of abrasion on enamel and dentine across consecutive brushing procedures. Varying brushing parameters had a significant impact on wear results: increased brushing force demonstrated a trend towards increased wear, with increased reproducibility for greater abrasion levels, highlighting the importance of achieving sufficient wear to optimise accuracy; increasing brushing temperature demonstrated increased enamel abrasion for silica and calcium carbonate systems, which may be related to slurry viscosities and particle suspension; varying brushing speed showed a small effect on abrasion of enamel at lower brushing speed, which may indicate the importance of maintenance of the abrasive in suspension. Adjusting key brushing variables significantly affected wear behaviour. The brushing simulator design provides a valuable model system for in vitro assessment of toothpaste abrasivity and the influence of variables in a controlled manner. Control of these variables will allow more reproducible study of in vitro tooth wear processes.

Method for determining the effects of oxygen plasma on a specimen

NASA Technical Reports Server (NTRS)

Whitaker, Ann F. (Inventor)

1991-01-01

A method for determining the effects of exposure of oxygen plasma on a specimen such as a thin film polymer or thin metals. The method includes providing an apparatus with a chamber having a holder supporting the polymer specimen in a plasma environment provided in the chamber. The chamber is regulated to a predetermined pressure and set temperature prior to the introduction of oxygen plasma therein. The specimen is then subjected to the plasma environment for a predetermined time during which time the temperature of the specimen is sensed and regulated to be maintained at the set temperature. Temperature sensing is accomplished by a probe which senses any changes in bulk sample temperature. Temperature regulation is provided by a thermoelectric module and by a coolant flow tube.

Apparatus for electrophoresis separation

DOEpatents

Anderson, Norman L.

1978-01-01

An apparatus is disclosed for simultaneously performing electrophoresis separations on a plurality of slab gels containing samples of protein, protein subunits or nucleic acids. A reservoir of buffer solution is divided into three compartments by two parallel partitions having vertical slots spaced along their length. A sheet of flexible, electrically insulative material is attached to each partition and is provided with vertical slits aligned with the slots. Slab-gel holders are received within the slots with the flexible material folded outwardly as flaps from the slits to overlay portions of the holder surfaces and thereby act as electrical and liquid seals. An elongated, spaghetti-like gel containing a sample of specimen that was previously separated by isoelectric focusing techniques is vertically positioned along a marginal edge portion of the slab gel. On application of an electrical potential between the two outer chambers of buffer solution, a second dimensional electrophoresis separation in accordance with molecular weight occurs as the specimen molecules migrate across the slab gel.

Specimen illumination apparatus with optical cavity for dark field illumination

DOEpatents

Pinkel, Daniel; Sudar, Damir; Albertson, Donna

1999-01-01

An illumination apparatus with a specimen slide holder, an illumination source, an optical cavity producing multiple reflection of illumination light to a specimen comprising a first and a second reflective surface arranged to achieve multiple reflections of light to a specimen is provided. The apparatus can further include additional reflective surfaces to achieve the optical cavity, a slide for mounting the specimen, a coverslip which is a reflective component of the optical cavity, one or more prisms for directing light within the optical cavity, antifading solutions for improving the viewing properties of the specimen, an array of materials for analysis, fluorescent components, curved reflective surfaces as components of the optical cavity, specimen detection apparatus, optical detection equipment, computers for analysis of optical images, a plane polarizer, fiberoptics, light transmission apertures, microscopic components, lenses for viewing the specimen, and upper and lower mirrors above and below the specimen slide as components of the optical cavity. Methods of using the apparatus are also provided.

Practical aspects of the use of the X(2) holder for HRTEM-quality TEM sample preparation by FIB.

PubMed

van Mierlo, Willem; Geiger, Dorin; Robins, Alan; Stumpf, Matthias; Ray, Mary Louise; Fischione, Paul; Kaiser, Ute

2014-12-01

The X(2) holder enables the effective production of thin, electron transparent samples for high-resolution transmission electron microscopy (HRTEM). Improvements to the X(2) holder for high-quality transmission electron microscopy (TEM) sample preparation are presented in this paper. We discuss the influence of backscattered electrons (BSE) from the sample holder in determining the lamella thickness in situ and demonstrate that a significant improvement in thickness determination can be achieved by comparatively simple means using the relative BSE intensity. We show (using Monte Carlo simulations) that by taking into account the finite collection angle of the electron backscatter detector, an approximately 20% underestimation of the lamella thickness in a silicon sample can be avoided. However, a correct thickness determination for light-element lamellas still remains a problem with the backscatter method; we introduce a more accurate method using the energy dispersive X-ray spectroscopy (EDX) signal for in situ thickness determination. Finally, we demonstrate how to produce a thin lamella with a nearly damage-free surface using the X(2) holder in combination with sub-kV polishing in the Fischione Instruments׳ NanoMill(®) TEM specimen preparation system. Copyright © 2014 Elsevier B.V. All rights reserved.

Theory of a time-dependent heat diffusion determination of thermal diffusivities with a single temperature measurement

DOE Office of Scientific and Technical Information (OSTI.GOV)

Perez, R. B.; Carroll, R. M.; Sisman, O.

1971-02-01

A method to measure the thermal diffusivity of reactor fuels during irradiation is developed, based on a time-dependent heat diffusion equation. With this technique the temperature is measured at only one point in the fuel specimen. This method has the advantage that it is not necessary to know the heat generation (a difficult evaluation during irradiation). The theory includes realistic boundary conditions, applicable to actual experimental systems. The parameters are the time constants associated with the first two time modes in the temperature-vs-time curve resulting from a step change in heat input to the specimen. With the time constants andmore » the necessary material properties and dimensions of the specimen and specimen holder, the thermal diffusivity of the specimen can be calculated.« less

In situ sputter cleaning of thin film metal substrates for UHV-TEM corrosion studies.

NASA Technical Reports Server (NTRS)

Heinemann, K.; Poppa, H.

1973-01-01

A prerequisite for conducting valid corrosion experiments by in situ electron microscopy techniques is not only the achievement of UHV background pressure conditions at the site of the specimen but also the ability to clean the surface of the thin metal substrate specimen before initiation of the corrosive interaction. A miniaturized simple ion gun has been constructed for this purpose. The gun is small enough to be incorporated into an UHV electron microscope specimen chamber with hot stage in such a way as to permit bombardment of the substrate specimen while observing it by transmission electron microscopy TEM. It is shown that the ion beam generated is confined well enough to cause a sputtering removal of substrate material at a rate of approximately 5-10 A/min and to prevent the sputter deposition of contaminating material from the specimen holder.

Pyrolysis kinetics and combustion of thin wood using advanced cone calorimetry test method

Treesearch

Mark A. Dietenberger

2011-01-01

Mechanistic pyrolysis kinetics analysis of extractives, holocellulose, and lignin in solid wood over entire heating regime was possible using specialized cone calorimeter test and new mathematical analysis tools. Added hardware components include: modified sample holder for thin specimen with tiny thermocouples, methane ring burner with stainless steel mesh above cone...

76 FR 8386 - Self-Regulatory Organizations; New York Stock Exchange LLC; Notice of Filing and Immediate...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-14

... brokers which are record holders of shares held in client accounts will no longer be permitted to vote... Sections 905.01, 905.02 and 905.03 contain specimens of letters containing the information and instructions... purposes provided all of the required information and instructions are clearly enumerated in letters to...

Pyrolysis kinetics and combustion of thin wood by an advanced cone caorimetry test method

Treesearch

Mark Dietenberger

2012-01-01

Pyrolysis kinetics analysis of extractives, holocellulose, and lignin in the solid redwood over the entire heating regime was possible by specialized cone calorimeter test and new mathematical analysis tools. Added hardware components include: modified sample holder for the thin specimen with tiny thermocouples, the methane ring burner with stainless-steel mesh above...

Tomographic Imaging of Water Injection and Withdrawal in PEMFC Gas Diffusion Layers

DOE Office of Scientific and Technical Information (OSTI.GOV)

McGill U; Gostick, J. T.; Gunterman, H. P.

2010-06-25

X-ray computed tomography was used to visualize the water configurations inside gas diffusion layers for various applied capillary pressures, corresponding to both water invasion and withdrawal. A specialized sample holder was developed to allow capillary pressure control on the small-scale samples required. Tests were performed on GDL specimens with and without hydrophobic treatments.

Gas permeation measurements on small polymer specimens

NASA Technical Reports Server (NTRS)

Burns, Karen S.; Vannorman, John D.

1988-01-01

Mass spectrometry was used to measure oxygen and nitrogen permeabilities while polarography was used to measure oxygen permeabilities for several contact lens materials. Applicable sample holders were designed and fabricated to accommodate curved and flat specimens. A prepared standard was used to calibrate the mass spectrometric analyses. The oxygen permeability values determined by mass spectrometry were significantly greater than those determined by polarography. This was attributed to the phase boundary phenomena and the limiting oxygen permeance of water inherent in the polarographic technique. Polarographic values determined were in good agreement with proprietary values obtained by polarography, with the exception of one material.

Origins of the elastic behavior of nanoparticle chain aggregates: Measurements using nanostructure manipulation device

NASA Astrophysics Data System (ADS)

Suh, Yong J.; Friedlander, Sheldon K.

2003-03-01

Nanoscale studies were conducted on the dynamic behavior of individual nanoparticle chain aggregates (NCAs) and their networks. For this purpose, device was fabricated to apply tension to NCA under controlled conditions. The device is composed of a specimen support and a cartridge. The specimen support is a deformable alloy disk with a narrow slit across which the NCAs are deposited; the cartridge is used to connect the specimen support to a specimen elongation support holder. The aggregates were stretched using the specimen holder to widen or narrow the slit gap at speeds from 0.5 to 300 nm/s and the motion was observed with a transmission electron microscope. Most of the studies were made with carbon NCA (primary particle size between 11 and 16 nm) generated by laser ablation of a graphite target. The aggregates were deposited on the specimen support (disk) to form bridges across the slit. When tension was applied, the NCA chains remained attached at the slit edges; the chains stretched as kinks on the scale of a few particle diameters were straightened by rotation and/or grain boundary sliding at particle-particle interfaces. After the chain became taut, increasing tension produced little additional extension. Eventually, the chain broke, the tension relaxed, and the elastically strained portions along the NCA recovered. This led to fast contraction of the two broken ends. In one of the cases studied in detail, a small primary particle in the chain doubled in length before the chain broke at this site. This probably occurred because of the high tensile stress in the small particle. In separate experiments, a network of carbon NCA was produced by increased deposition around the slit of a specimen support. Chains in the network broke successively as the network stretched. Some of the chains broke midway and not at the junctures with each other. They contracted fast showing behavior similar to that of the individual aggregates. Possible applications to the behavior of nanocomposite materials composed of blends of NCAs and molecular polymers (e.g., rubber) are described.

Carbon distribution profiles in lunar fines

NASA Technical Reports Server (NTRS)

Hart, R. K.

1977-01-01

Radial distribution profiles of elemental carbon in lunar soils consisting of particles in the size range of 50 to 150 microns were investigated. Initial experiments on specimen preparation and the analysis of prepared specimens by Auger electron spectrometry (AES) and scanning electron microscopy (SEM) are described. Results from splits of samples 61501,84 and 64421,11, which were mounted various ways in several specimen holders, are presented. A low carbon content was observed in AES spectra from soil particles that were subjected to sputter-ion cleaning with 960eV argon ions for periods of time up to a total exposure for one hour. This ion charge was sufficient to remove approximately 70 nm of material from the surface. All of the physically adsorbed carbon (as well as water vapor, etc.) would normally be removed in the first few minutes, leaving only carbon in the specimen, and metal support structure, to be detected thereafter.

Hand-held photomicroscope

NASA Technical Reports Server (NTRS)

Zabower, H. R. (Inventor)

1973-01-01

A small, lightweight, compact, hand-held photomicroscope provides simultaneous viewing and photographing, with adjustable specimen illumination and exchangeable camera format. The novel photomicroscope comprises a main housing having a top plate, bottom plate, and side walls. The objective lens is mounted on the top plate in an inverted manner relative to the normal type of mounting. The specimen holder has an adjusting mechanism for adjustably moving the specimen vertically along an axis extending through the objective lens as well as transverse of the axis. The lens system serves to split the beam of light into two paths, one to the eyepiece and the other to a camera mounting. A light source is mounted on the top plate and directs light onto the specimen. A rheostat device is mounted on the top plate and coupled to the power supply for the light source so that the intensity of the light may be varied.

Development of a plasma driven permeation experiment for TPE

DOE PAGES

Buchenauer, Dean; Kolasinski, Robert; Shimada, Masa; ...

2014-04-18

Experiments on retention of hydrogen isotopes (including tritium) at temperatures less than 800 ?C have been carried out in the Tritium Plasma Experiment (TPE) at Idaho National Laboratory [1,2]. To provide a direct measurement of plasma driven permeation in plasma facing materials at temperatures reaching 1000 ?C, a new TPE membrane holder has been built to hold test specimens (=1 mm in thickness) at high temperature while measuring tritium permeating through the membrane from the plasma facing side. This measurement is accomplished by employing a carrier gas that transports the permeating tritium from the backside of the membrane to ionmore » chambers giving a direct measurement of the plasma driven tritium permeation rate. Isolation of the membrane cooling and sweep gases from TPE’s vacuum chamber has been demonstrated by sealing tests performed up to 1000 ?C of a membrane holder design that provides easy change out of membrane specimens between tests. Simulations of the helium carrier gas which transports tritium to the ion chamber indicate a very small pressure drop (~700 Pa) with good flow uniformity (at 1000 sccm). Thermal transport simulations indicate that temperatures up to 1000 ?C are expected at the highest TPE fluxes.« less

Design of a 300-kV gas environmental transmission electron microscope equipped with a cold field emission gun.

PubMed

Isakozawa, Shigeto; Nagaoki, Isao; Watabe, Akira; Nagakubo, Yasuhira; Saito, Nobuhiro; Matsumoto, Hiroaki; Zhang, Xiao Feng; Taniguchi, Yoshifumi; Baba, Norio

2016-08-01

A new in situ environmental transmission electron microscope (ETEM) was developed based on a 300 kV TEM with a cold field emission gun (CFEG). Particular caution was taken in the ETEM design to assure uncompromised imaging and analytical performance of the TEM. Because of the improved pumping system between the gun and column, the vacuum of CFEG was largely improved and the probe current was sufficiently stabilized to operate without tip flashing for 2-3 h or longer. A high brightness of 2.5 × 10(9) A/cm(2) sr was measured at 300 kV, verifying the high quality of the CFEG electron beam. A specially designed gas injection-heating holder was used in the in situ TEM study at elevated temperatures with or without gas around the TEM specimen. Using this holder in a 10 Pa gas atmosphere and specimen temperatures up to 1000°C, high-resolution ETEM performance and analysis were achieved. © The Author 2016. Published by Oxford University Press on behalf of The Japanese Society of Microscopy. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

A new apparatus for electron tomography in the scanning electron microscope

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morandi, V., E-mail: morandi@bo.imm.cnr.it; Maccagnani, P.; Masini, L.

2015-06-23

The three-dimensional reconstruction of a microscopic specimen has been obtained by applying the tomographic algorithm to a set of images acquired in a Scanning Electron Microscope. This result was achieved starting from a series of projections obtained by stepwise rotating the sample under the beam raster. The Scanning Electron Microscope was operated in the scanning-transmission imaging mode, where the intensity of the transmitted electron beam is a monotonic function of the local mass-density and thickness of the specimen. The detection strategy has been implemented and tailored in order to maintain the projection requirement over the large tilt range, as requiredmore » by the tomographic workflow. A Si-based electron detector and an eucentric-rotation specimen holder have been specifically developed for the purpose.« less

STEM-EDX tomography of bimetallic nanoparticles: A methodological investigation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Slater, Thomas J. A.; Janssen, Arne; Camargo, Pedro H. C.

This paper presents an investigation of the limitations and optimization of energy dispersive X-ray (EDX) tomography within the scanning transmission electron microscope, focussing on application of the technique to characterising the 3D elemental distribution of bimetallic AgAu nanoparticles. The detector collection efficiency when using a standard tomography holder is characterised using a tomographic data set from a single nanoparticle and compared to a standard low background double tilt holder. Optical depth profiling is used to investigate the angles and origin of detector shadowing as a function of specimen field of view. A novel time-varied acquisition scheme is described to compensatemore » for variations in the intensity of spectrum images at each sample tilt. Lastly, the ability of EDX spectrum images to satisfy the projection requirement for nanoparticle samples is discussed, with consideration of the effect of absorption and shadowing variations« less

STEM-EDX tomography of bimetallic nanoparticles: A methodological investigation

DOE PAGES

Slater, Thomas J. A.; Janssen, Arne; Camargo, Pedro H. C.; ...

2015-10-22

This paper presents an investigation of the limitations and optimization of energy dispersive X-ray (EDX) tomography within the scanning transmission electron microscope, focussing on application of the technique to characterising the 3D elemental distribution of bimetallic AgAu nanoparticles. The detector collection efficiency when using a standard tomography holder is characterised using a tomographic data set from a single nanoparticle and compared to a standard low background double tilt holder. Optical depth profiling is used to investigate the angles and origin of detector shadowing as a function of specimen field of view. A novel time-varied acquisition scheme is described to compensatemore » for variations in the intensity of spectrum images at each sample tilt. Lastly, the ability of EDX spectrum images to satisfy the projection requirement for nanoparticle samples is discussed, with consideration of the effect of absorption and shadowing variations« less

The Manufacturing of High Porosity Iron with an Ultra-Fine Microstructure via Free Pressureless Spark Plasma Sintering

PubMed Central

Cui, Guodong; Wei, Xialu; Olevsky, Eugene A.; German, Randall M.; Chen, Junying

2016-01-01

High porosity (>40 vol %) iron specimens with micro- and nanoscale isotropic pores were fabricated by carrying out free pressureless spark plasma sintering (FPSPS) of submicron hollow Fe–N powders at 750 °C. Ultra-fine porous microstructures are obtained by imposing high heating rates during the preparation process. This specially designed approach not only avoids the extra procedures of adding and removing space holders during the formation of porous structures, but also triggers the continued phase transitions of the Fe–N system at relatively lower processing temperatures. The compressive strength and energy absorption characteristics of the FPSPS processed specimens are examined here to be correspondingly improved as a result of the refined microstructure. PMID:28773617

An improved FIB sample preparation technique for site-specific plan-view specimens: A new cutting geometry.

PubMed

Li, Chen; Habler, Gerlinde; Baldwin, Lisa C; Abart, Rainer

2018-01-01

Focused ion beam (FIB) sample preparation technique in plan-view geometry allows direct correlations of the atomic structure study via transmission electron microscopy with micrometer-scale property measurements. However, one main technical difficulty is that a large amount of material must be removed underneath the specimen. Furthermore, directly monitoring the milling process is difficult unless very large material volumes surrounding the TEM specimen site are removed. In this paper, a new cutting geometry is introduced for FIB lift-out sample preparation with plan-view geometry. Firstly, an "isolated" cuboid shaped specimen is cut out, leaving a "bridge" connecting it with the bulk material. Subsequently the two long sides of the "isolated" cuboid are wedged, forming a triangular prism shape. A micromanipulator needle is used for in-situ transfer of the specimen to a FIB TEM grid, which has been mounted parallel with the specimen surface using a simple custom-made sample slit. Finally, the grid is transferred to the standard FIB grid holder for final thinning with standard procedures. This new cutting geometry provides clear viewing angles for monitoring the milling process, which solves the difficulty of judging whether the specimen has been entirely detached from the bulk material, with the least possible damage to the surrounding materials. With an improved success rate and efficiency, this plan-view FIB lift-out specimen preparation technique should have a wide application for material science. Copyright © 2017 The Authors. Published by Elsevier B.V. All rights reserved.

The Manufacturing of High Porosity Iron with an Ultra-Fine Microstructure via Free Pressureless Spark Plasma Sintering

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cui, Guodong; Wei, Xialu; Olevsky, Eugene

2016-06-01

High porosity (>40 vol %) iron specimens with micro- and nanoscale isotropic pores were fabricated by carrying out free pressureless spark plasma sintering (FPSPS) of submicron hollow Fe–N powders at 750 °C. Ultra-fine porous microstructures are obtained by imposing high heating rates during the preparation process. This specially designed approach not only avoids the extra procedures of adding and removing space holders during the formation of porous structures, but also triggers the continued phase transitions of the Fe–N system at relatively lower processing temperatures. In conclusion, the compressive strength and energy absorption characteristics of the FPSPS processed specimens are examinedmore » here to be correspondingly improved as a result of the refined microstructure.« less

In situ TEM Raman spectroscopy and laser-based materials modification.

PubMed

Allen, F I; Kim, E; Andresen, N C; Grigoropoulos, C P; Minor, A M

2017-07-01

We present a modular assembly that enables both in situ Raman spectroscopy and laser-based materials processing to be performed in a transmission electron microscope. The system comprises a lensed Raman probe mounted inside the microscope column in the specimen plane and a custom specimen holder with a vacuum feedthrough for a tapered optical fiber. The Raman probe incorporates both excitation and collection optics, and localized laser processing is performed using pulsed laser light delivered to the specimen via the tapered optical fiber. Precise positioning of the fiber is achieved using a nanomanipulation stage in combination with simultaneous electron-beam imaging of the tip-to-sample distance. Materials modification is monitored in real time by transmission electron microscopy. First results obtained using the assembly are presented for in situ pulsed laser ablation of MoS 2 combined with Raman spectroscopy, complimented by electron-beam diffraction and electron energy-loss spectroscopy. Copyright © 2016 Elsevier B.V. All rights reserved.

Comparative Evaluation of Marginal Discrepancy in Tooth Colored Self Cure Acrylic Provisional Restorations With and Without Reinforcement of Glass Beads: An In-Vitro Study.

PubMed

Yasangi, Manoj Kumar; Mannem, Dhanalakshmi; Bommireddy, Vikram Simha; Neturi, Sirisha; Ravoori, Srinivas; Jyothi

2015-05-01

This invitro study was conducted to compare and evaluate marginal discrepancy in two types of tooth colored self cure provisional restorative materials {DPI&UNIFAST TRAD} before and after reinforcement of glass beads. The aim of the present study was to evaluate and compare marginal discrepancy in two types of provisional restorative materials (DPI and UNI FAST TRAD) before and after reinforcement with Glass beads. Tooth shaped resin copings were fabricated on custom made brass metal die. A total of 60 resin copings were fabricated in which 30 samples were prepared with DPI and 30 samples with UNIFAST material. Each group of 30 samples were divided in to two sub groups in which 15 samples were prepared with glass bead reinforcement and 15 samples without reinforcement. The marginal discrepancy was evaluated with photomicroscope {Reichet Polyvar 2 met} by placing the resin copings on custom made brass resin coping holder. Measurements obtained were statistically analysed by unpaired t-test to know any significance between two variables. Unreinforced DPI specimens had shown lower marginal discrepancy (442.82) than reinforced specimens (585.77). Unreinforced UNIFAST specimens have shown high values of marginal discrepancy (592.83) than reinforced specimens (436.35). p-value between reinforced and unreinforced specimens of DPI (p=0.0013) and UNIFAST (p= 0.0038) has shown statistical significance. This in-vitro study revealed that unreinforced DPI specimens have shown lower marginal discrepancy than reinforced specimens and unreinforced UNIFAST specimens have shown higher values of marginal discrepancy than reinforced specimens.

An improved cryo-FIB method for fabrication of frozen hydrated lamella.

PubMed

Zhang, Jianguo; Ji, Gang; Huang, Xiaojun; Xu, Wei; Sun, Fei

2016-05-01

Cryo-electron tomography (cryo-ET) provides great insights into the ultrastructure of cells and tissues in their native state and provides a promising way to study the in situ 3D structures of macromolecular complexes. However, this technique has been limited on the very thin specimen, which is not applicable for most cells and tissues. Besides cryo-sectioning approach, cryo focused ion beam (cryo-FIB) appeared recently to achieve 'artifact-free' thin frozen hydrated lamella via fabrication. Considering that the current cryo-FIB methods need modified holders or cartridges, here, with a "D-shaped" molybdenum grid and a specific shutter system, we developed a simple cryo-FIB approach for thin frozen hydrated lamella fabrication, which fits both standard transmission cryo-electron microscopes with side-entry cryo-holders and state-of-the-art ones with AutoGrids. Our approach will expand the usage of cryo-FIB approach in many labs. Copyright © 2016 The Authors. Published by Elsevier Inc. All rights reserved.

Blood Vessel Tension Tester

NASA Technical Reports Server (NTRS)

1978-01-01

In the photo, a medical researcher is using a specially designed laboratory apparatus for measuring blood vessel tension. It was designed by Langley Research Center as a service to researchers of Norfolk General Hospital and Eastern Virginia Medical School, Norfolk, Virginia. The investigators are studying how vascular smooth muscle-muscle in the walls of blood vessels-reacts to various stimulants, such as coffee, tea, alcohol or drugs. They sought help from Langley Research Center in devising a method of measuring the tension in blood vessel segments subjected to various stimuli. The task was complicated by the extremely small size of the specimens to be tested, blood vessel "loops" resembling small rubber bands, some only half a millimeter in diameter. Langley's Instrumentation Development Section responded with a miniaturized system whose key components are a "micropositioner" for stretching a length of blood vessel and a strain gage for measuring the smooth muscle tension developed. The micropositioner is a two-pronged holder. The loop of Mood vessel is hooked over the prongs and it is stretched by increasing the distance between the prongs in minute increments, fractions of a millimeter. At each increase, the tension developed is carefully measured. In some experiments, the holder and specimen are lowered into the test tubes shown, which contain a saline solution simulating body fluid; the effect of the compound on developed tension is then measured. The device has functioned well and the investigators say it has saved several months research time.

Measuring Hydrogen Concentrations in Metals

NASA Technical Reports Server (NTRS)

Danford, M. D.

1985-01-01

Commercial corrosion-measurement system adapted to electrochemical determination of hydrogen concentrations in metals. New technique based on diffusion of hydrogen through foil specimen of metal. In sample holder, hydrogen produced on one side of foil, either by corrosion reaction or by cathodic current. Hydrogen diffused through foil removed on other side by constant anode potential, which leads to oxidation of hydrogen to water. Anode current is measure of concentration of hydrogen diffusing through foil. System used to study hydrogen uptake, hydrogen elimination by baking, effect of heat treatment, and effect of electroplating on high-strength steels.

Comparative Evaluation of Marginal Discrepancy in Tooth Colored Self Cure Acrylic Provisional Restorations With and Without Reinforcement of Glass Beads: An In-Vitro Study

PubMed Central

Yasangi, Manoj Kumar; Mannem, Dhanalakshmi; Neturi, Sirisha; Ravoori, Srinivas; Jyothi

2015-01-01

Context This invitro study was conducted to compare and evaluate marginal discrepancy in two types of tooth colored self cure provisional restorative materials {DPI&UNIFAST TRAD} before and after reinforcement of glass beads. Aim The aim of the present study was to evaluate and compare marginal discrepancy in two types of provisional restorative materials (DPI and UNI FAST TRAD) before and after reinforcement with Glass beads. Materials and Methods Tooth shaped resin copings were fabricated on custom made brass metal die. A total of 60 resin copings were fabricated in which 30 samples were prepared with DPI and 30 samples with UNIFAST material. Each group of 30 samples were divided in to two sub groups in which 15 samples were prepared with glass bead reinforcement and 15 samples without reinforcement. The marginal discrepancy was evaluated with photomicroscope {Reichet Polyvar 2 met} by placing the resin copings on custom made brass resin coping holder. Results Measurements obtained were statistically analysed by unpaired t-test to know any significance between two variables. Unreinforced DPI specimens had shown lower marginal discrepancy (442.82) than reinforced specimens (585.77). Unreinforced UNIFAST specimens have shown high values of marginal discrepancy (592.83) than reinforced specimens (436.35). p-value between reinforced and unreinforced specimens of DPI (p=0.0013) and UNIFAST (p= 0.0038) has shown statistical significance. Conclusion This in-vitro study revealed that unreinforced DPI specimens have shown lower marginal discrepancy than reinforced specimens and unreinforced UNIFAST specimens have shown higher values of marginal discrepancy than reinforced specimens. PMID:26155574

Abrasion resistance of direct and indirect resins as a function of a sealant veneer.

PubMed

Ferraz Caneppele, Taciana Marco; Rocha, Daniel Maranha; Màximo Araujo, Maria Amelia; Valera, Màrcia Carneiro; Salazar Marocho, Susana MarIa

2014-01-01

Abrasive wear is one of the most common type of wear that not only affect teeth, as also dental restorations. Thus to investigate one of the etiological factors as tooth brushing procedure is clinical relevant in order to select the best material combination that may prevent damage of resin dental restoration's abrasion. This study evaluated the influence of tooth brushing on mass loss and surface roughness of direct Venus (Vs) and indirect Signum (Sg) resin composites, with and without a surface sealant, Fortify (F). Twenty-four specimens were prepared with each resin composite, using their proprietary curing units, according to manufacturer's instructions. All the specimens were polished and ultrasonically cleaned in distilled water for 5 minutes. Half of the specimens of each resin (n = 12) were covered with F (Vs F and Sg F ), except for the control (C) specimens (Vs C and Sg C ), which were not sealed. Mass loss (ML) as well as surface roughness (Ra ) was measured for all the specimens. Then, the specimens were subjected to toothbrush-dentifrice abrasion, using a testing machine for 67.000 brushing strokes, in an abrasive slurry. After brushing simulation, the specimens were removed from the holder, rinsed thoroughly and blot dried with soft absorbent paper. The abrasion of the material was quantitatively determined with final measurements of ML and surface roughness, using the method described above. ML data were analyzed by two-way analysis of variance (ANOVA) and the analysis indicated that resin composites were not statistically different; however, the specimens sealed with F showed higher ML. Ra mean values of the groups Vs F and Sg F significantly increased. Tooth brushing affects mainly the roughness of the direct and indirect resin composites veneered with a sealant.

Preserving and vouchering butterflies and moths for large-scale museum-based molecular research

PubMed Central

Epstein, Samantha W.; Mitter, Kim; Hamilton, Chris A.; Plotkin, David; Mitter, Charles

2016-01-01

Butterflies and moths (Lepidoptera) comprise significant portions of the world’s natural history collections, but a standardized tissue preservation protocol for molecular research is largely lacking. Lepidoptera have traditionally been spread on mounting boards to display wing patterns and colors, which are often important for species identification. Many molecular phylogenetic studies have used legs from pinned specimens as the primary source for DNA in order to preserve a morphological voucher, but the amount of available tissue is often limited. Preserving an entire specimen in a cryogenic freezer is ideal for DNA preservation, but without an easily accessible voucher it can make specimen identification, verification, and morphological work difficult. Here we present a procedure that creates accessible and easily visualized “wing vouchers” of individual Lepidoptera specimens, and preserves the remainder of the insect in a cryogenic freezer for molecular research. Wings are preserved in protective holders so that both dorsal and ventral patterns and colors can be easily viewed without further damage. Our wing vouchering system has been implemented at the University of Maryland (AToL Lep Collection) and the University of Florida (Florida Museum of Natural History, McGuire Center of Lepidoptera and Biodiversity), which are among two of the largest Lepidoptera molecular collections in the world. PMID:27366654

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ogura, Toshihiko, E-mail: t-ogura@aist.go.jp

Scanning electron microscopy (SEM) has been widely used to examine biological specimens of bacteria, viruses and proteins. Until now, atmospheric and/or wet biological specimens have been examined using various atmospheric holders or special equipment involving SEM. Unfortunately, they undergo heavy radiation damage by the direct electron beam. In addition, images of unstained biological samples in water yield poor contrast. We recently developed a new analytical technology involving a frequency transmission electric-field (FTE) method based on thermionic SEM. This method is suitable for high-contrast imaging of unstained biological specimens. Our aim was to optimise the method. Here we describe a high-resolutionmore » FTE system based on field-emission SEM; it allows for imaging and nanoscale examination of various biological specimens in water without radiation damage. The spatial resolution is 8 nm, which is higher than 41 nm of the existing FTE system. Our new method can be easily utilised for examination of unstained biological specimens including bacteria, viruses and protein complexes. Furthermore, our high-resolution FTE system can be used for diverse liquid samples across a broad range of scientific fields, e.g. nanoparticles, nanotubes and organic and catalytic materials. - Highlights: • We developed a high-resolution frequency transmission electric-field (FTE) system. • High-resolution FTE system is introduced in the field-emission SEM. • The spatial resolution of high-resolution FTE method is 8 nm. • High-resolution FTE system enables observation of the intact IgM particles in water.« less

Highly Porous NiTi with Isotropic Pore Morphology Fabricated by Self-Propagated High-Temperature Synthesis

NASA Astrophysics Data System (ADS)

Hosseini, S. A.; Alizadeh, M.; Ghasemi, A.; Meshkot, M. A.

2013-02-01

Highly porous NiTi with isotropic pore morphology has been successfully produced by self-propagating high-temperature synthesis of elemental Ni/Ti metallic powders. The effects of adding urea and NaCl as temporary pore fillers were investigated on pore morphology, microstructure, chemical composition, and the phase transformation temperatures of specimens. These parameters were studied by optical microscopy, scanning electron microscopy, x-ray diffraction, and differential scanning calorimetry (DSC). Highly porous specimens were obtained with up to 83% total porosity and pore sizes between 300 and 500 μm in diameter. Results show pore characteristics were improved from anisotropic to isotropic and pore morphology was changed from channel-like to irregular by adding pore filler powders. Furthermore, the highly porous specimens produced when using urea as a space holder, were of more uniform composition in comparison to NaCl. DSC results showed that a two-step martensitic phase transformation takes place during the cooling cycles and the austenite finish temperature ( A f) is close to human body temperature. Compression test results reveal that the compressive strength of highly porous NiTi is about 155 MPa and recoverable strain about 6% in superelasticity regime.

In-situ monitoring of acoustic linear and nonlinear behavior of titanium alloys during cycling loading

NASA Astrophysics Data System (ADS)

Frouin, Jerome; Matikas, Theodore E.; Na, Jeong K.; Sathish, Shamachary

1999-02-01

An in-situ technique to measure sound velocity, ultrasonic attenuation and acoustic nonlinear property has been developed for characterization and early detection of fatigue damage in aerospace materials. A previous experiment using the f-2f technique on Ti-6Al-4V dog bone specimen fatigued at different stage of fatigue has shown that the material nonlinearity exhibit large change compared to the other ultrasonic parameter. Real-time monitoring of the nonlinearity may be a future tool to characterize early fatigue damage in the material. For this purpose we have developed a computer software and measurement technique including hardware for the automation of the measurement. New transducer holder and special grips are designed. The automation has allowed us to test the long-term stability of the electronics over a period of time and so proof of the linearity of the system. For the first time, a real-time experiment has been performed on a dog-bone specimen from zero fatigue al the way to the final fracture.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kawasaki, Tadahiro; PRESTO-JST, 4-1-8 Honcho, Kawaguchi, Saitama 332-0012; Ueda, Kouta

We have developed an improved, windowed type environmental-cell (E-cell) transmission electron microscope (TEM) for in situ observation of gas-solid interactions, such as catalytic reactions at atmospheric pressure. Our E-cell TEM includes a compact E-cell specimen holder with mechanical stability, resulting in smoother introduction of the desired gases compared with previous E-cell TEMs. In addition, the gas control unit was simplified by omitting the pressure control function of the TEM pre-evacuation chamber. This simplification was due to the successful development of remarkably tough thin carbon films as the window material. These films, with a thickness of <10 nm, were found tomore » withstand pressure differences >2 atm. Appropriate arrangement of the specimen position inside the E-cell provided quantitatively analyzable TEM images, with no disturbances caused by the windowed films. As an application, we used this E-cell TEM to observe the dynamic shape change in a catalytic gold nanoparticle supported on TiO{sub 2} during the oxidation of CO gas.« less

Proton-induces and x-ray induced fluorescence analysis of scoliotic tissue

DOE Office of Scientific and Technical Information (OSTI.GOV)

Panessa-Warren, B J; Kraner, H W; Jones, K W

1980-02-01

Adolescent idiopathic scoliosis is characterized by a curvature or assymetry of the spine which may become progressively more severe, with clinical symptoms appearing just prior to, or during, puberty. The incidence for scoliosis in the age group from 12 to 14 years of age has been reported as high as 8 to 10%, with more than 80% of the cases occurring in females. Although pathologic changes exist in muscles from both sides of the spinal curvature, and no statistically significant side differences have been reported, morphologic changes suggest that the concanve side is the most affected. This paper reports ourmore » preliminary data on the elemental composition of individual muscle fibers derived from convex, concave and gluteal scoliotic muscle, and erythrocytes from scoliotic and normal patients, analyzed by proton induced x-ray emission (PIXE) and x-ray fluorescence spectroscopy (XRF). A new type of specimen holder was designed for this study which offers low x-ray background, minimal absorption and maintenance of a moist environment around the specimen.« less

Transmission Kikuchi diffraction and transmission electron forescatter imaging of electropolished and FIB manufactured TEM specimens

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zieliński, W., E-mail: wiziel@inmat.pw.edu.pl; Płociński, T.; Kurzydłowski, K.J.

2015-06-15

We present a study of the efficiency of the utility of scanning electron microscope (SEM)-based transmission methods for characterizing grain structure in thinned bulk metals. Foils of type 316 stainless steel were prepared by two methods commonly used for transmission electron microscopy — double-jet electropolishing and focused ion beam milling. A customized holder allowed positioning of the foils in a configuration appropriate for both transmission electron forward scatter diffraction, and for transmission imaging by the use of a forescatter detector with two diodes. We found that both crystallographic orientation maps and dark-field transmitted images could be obtained for specimens preparedmore » by either method. However, for both methods, preparation-induced artifacts may affect the quality or accuracy of transmission SEM data, especially those acquired by the use of transmission Kikuchi diffraction. Generally, the quality of orientation data was better for specimens prepared by electropolishing, due to the absence of ion-induced damage. - Highlights: • The transmission imaging and diffraction techniques are emerging in scanning electron microscopy (SEM) as promising new field of materials characterization. • The manuscript titled: “Transmission Kikuchi Diffraction and Transmission Electron Forescatter Imaging of Electropolished and FIB Manufactured TEM Specimens” documents how different specimen thinning procedures can effect efficiency of transmission Kikuchi diffraction and transmission electron forescatter imaging. • The abilities to make precision crystallographic orientation maps and dark-field images in transmission was studied on electropolished versus focus ion beam manufactured TEM specimens. • Depending on the need, electropolished and focused ion beam technique may produce suitable specimens for transmission imaging and diffraction in SEM.« less

Electron tomography of HEK293T cells using scanning electron microscope-based scanning transmission electron microscopy.

PubMed

You, Yun-Wen; Chang, Hsun-Yun; Liao, Hua-Yang; Kao, Wei-Lun; Yen, Guo-Ji; Chang, Chi-Jen; Tsai, Meng-Hung; Shyue, Jing-Jong

2012-10-01

Based on a scanning electron microscope operated at 30 kV with a homemade specimen holder and a multiangle solid-state detector behind the sample, low-kV scanning transmission electron microscopy (STEM) is presented with subsequent electron tomography for three-dimensional (3D) volume structure. Because of the low acceleration voltage, the stronger electron-atom scattering leads to a stronger contrast in the resulting image than standard TEM, especially for light elements. Furthermore, the low-kV STEM yields less radiation damage to the specimen, hence the structure can be preserved. In this work, two-dimensional STEM images of a 1-μm-thick cell section with projection angles between ±50° were collected, and the 3D volume structure was reconstructed using the simultaneous iterative reconstructive technique algorithm with the TomoJ plugin for ImageJ, which are both public domain software. Furthermore, the cross-sectional structure was obtained with the Volume Viewer plugin in ImageJ. Although the tilting angle is constrained and limits the resulting structural resolution, slicing the reconstructed volume generated the depth profile of the thick specimen with sufficient resolution to examine cellular uptake of Au nanoparticles, and the final position of these nanoparticles inside the cell was imaged.

Comparison of reflectance spectra of sound and carious enamel

NASA Astrophysics Data System (ADS)

Analoui, Mostafa; Ando, Masatoshi; Stookey, George K.

2000-03-01

Development of dental caries is associated with the loss of minerals and change in the enamel structure. In this study, we have measured and compared reflectance spectra of sound and carious enamel, to investigate its utility in detection and analysis of dental caries. One hundred twenty, 3-mm diameter human enamel cores, with no sign of fluorosis, tetracycline stain, hypoplasia, fracture and restorations, were prepared. The enamel surfaces then were ground and polished. Specimens were placed on a fitted holder with either black or white color for background, with no fluorescence. The baseline spectra were measured using a spectrophotometer with enclosed diffused illumination. Spectra measured from 380 to 780 nm at 5 nm intervals. All measurements were corrected to compensate for the spectrum of illumination. The specimens were divided into two groups and exposed to a demineralizing solution, for 48 and 96 hours, respectively. Reflectance spectra of specimens were measured following lesion induction. All specimens were sectioned and analyzed by transverse microradiography (TMR), where lesion depth and mineral loss ((Delta) Z) were measured. Dimensionality of multi-spectral data was reduced through its conversion to L*a*b* color coordinates and principal component analysis (PCA). Multiple linear regression analysis showed low correlation between L*a*b* and lesion depth and mineral loss. PCA analysis showed higher correlation coefficient, compared to L*a*b*. Preliminary results of this study suggest that multi-spectral measurement and analysis of the tooth surface could be useful in predicting the depth and severity of an early carious lesion.

Dynamic deformation of soft soil media: Experimental studies and mathematical modeling

NASA Astrophysics Data System (ADS)

Balandin, V. V.; Bragov, A. M.; Igumnov, L. A.; Konstantinov, A. Yu.; Kotov, V. L.; Lomunov, A. K.

2015-05-01

A complex experimental-theoretical approach to studying the problem of high-rate strain of soft soil media is presented. This approach combines the following contemporary methods of dynamical tests: the modified Hopkinson-Kolsky method applied tomedium specimens contained in holders and the method of plane wave shock experiments. The following dynamic characteristics of sand soils are obtained: shock adiabatic curves, bulk compressibility curves, and shear resistance curves. The obtained experimental data are used to study the high-rate strain process in the system of a split pressure bar, and the constitutive relations of Grigoryan's mathematical model of soft soil medium are verified by comparing the results of computational and natural test experiments of impact and penetration.

19 CFR 10.7 - Substantial containers or holders.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 19 Customs Duties 1 2010-04-01 2010-04-01 false Substantial containers or holders. 10.7 Section 10... Exported and Returned § 10.7 Substantial containers or holders. (a) Substantial containers or holders... domestic products exported and returned. When such containers or holders are imported not containing or...

Utility of a Newly Designed Film Holder for Premolar Bitewing Radiography.

PubMed

Safi, Yaser; Esmaeelinejad, Mohammad; Vasegh, Zahra; Valizadeh, Solmaz; Aghdasi, Mohammad Mehdi; Sarani, Omid; Afsahi, Mahmoud

2015-11-01

Bitewing radiography is a valuable technique for assessment of proximal caries, alveolar crest and periodontal status. Technical errors during radiography result in erroneous radiographic interpretation, misdiagnosis, possible mistreatment or unnecessary exposure of patient for taking a repeat radiograph. In this study, we aimed to evaluate the efficacy of a film holder modified from the conventional one and compared it with that of conventional film holder. Our study population comprised of 70 patients who were referred to the Radiology Department for bilateral premolar bitewing radiographs as requested by their attending clinician. Bitewing radiographs in each patient were taken using the newly designed holder in one side and the conventional holder in the other side. The acceptability of the two holders from the perspectives of the technician and patients was determined using a 0-20 point scale. The frequency of overlap and film positioning errors was calculated for each method. The conventional holder had greater acceptability among patients compared to the newly designed holder (mean score of 16.59 versus 13.37). From the technicians' point of view, the newly designed holder was superior to the conventional holder (mean score of 17.33 versus 16.44). The frequency of overlap was lower using the newly designed holder (p<0.001) and it allowed more accurate film positioning (p=0.005). The newly designed holder may facilitate the process of radiography for technicians and may be associated with less frequency of radiographic errors compared to the conventional holder.

Electromyographic Comparison of Forearm Muscle Movements for Fine Skin Suturing Between an Enlarged Pen Needle Holder and a Webster Needle Holder

PubMed Central

Ohata, Erika; Matsuo, Kiyoshi; Ban, Ryokuya; Shiba, Masato; Yasunaga, Yoshichika

2013-01-01

Background: For surgical suturing, a Webster needle holder uses wrist supinating with supinator and extrinsic muscles, whereas a pen needle holder uses finger twisting with intrinsic and extrinsic muscles. Because the latter is better suited to microsurgery, which requires fine suturing with less forearm muscle movement, we have recently adopted an enlarged pen needle holder scaled from a micro needle holder for fine skin suturing. In this study, we assessed whether the enlarged pen needle holder reduced forearm muscle movement during fine skin suturing as compared with the Webster needle holder. Methods: A fine skin-suturing task was performed using pen holding with the enlarged micro needle holder or scissor holding with the Webster needle holder by 9 experienced and 6 inexperienced microsurgeons. The task lasted for 60 seconds and was randomly performed 3 times for each method. Forearm flexor and extensor muscular activities were evaluated by surface electromyography. Results: The enlarged pen needle holder method required significantly less forearm muscle movement for experienced microsurgeons despite it being their first time using the instrument. There was no significant difference between 2 methods for inexperienced microsurgeons. Conclusions: Experienced microsurgeons conserved forearm muscle movement by finger twisting in fine skin suturing with the enlarged pen needle holder. Inexperienced microsurgeons may benefit from the enlarged pen needle holder, even for fine skin suturing, to develop their internal acquisition model of the dynamics of finger twisting. PMID:23691259

Electromyographic comparison of forearm muscle movements for fine skin suturing between an enlarged pen needle holder and a webster needle holder.

PubMed

Ohata, Erika; Matsuo, Kiyoshi; Ban, Ryokuya; Shiba, Masato; Yasunaga, Yoshichika

2013-01-01

For surgical suturing, a Webster needle holder uses wrist supinating with supinator and extrinsic muscles, whereas a pen needle holder uses finger twisting with intrinsic and extrinsic muscles. Because the latter is better suited to microsurgery, which requires fine suturing with less forearm muscle movement, we have recently adopted an enlarged pen needle holder scaled from a micro needle holder for fine skin suturing. In this study, we assessed whether the enlarged pen needle holder reduced forearm muscle movement during fine skin suturing as compared with the Webster needle holder. A fine skin-suturing task was performed using pen holding with the enlarged micro needle holder or scissor holding with the Webster needle holder by 9 experienced and 6 inexperienced microsurgeons. The task lasted for 60 seconds and was randomly performed 3 times for each method. Forearm flexor and extensor muscular activities were evaluated by surface electromyography. The enlarged pen needle holder method required significantly less forearm muscle movement for experienced microsurgeons despite it being their first time using the instrument. There was no significant difference between 2 methods for inexperienced microsurgeons. Experienced microsurgeons conserved forearm muscle movement by finger twisting in fine skin suturing with the enlarged pen needle holder. Inexperienced microsurgeons may benefit from the enlarged pen needle holder, even for fine skin suturing, to develop their internal acquisition model of the dynamics of finger twisting.

OMNY PIN—A versatile sample holder for tomographic measurements at room and cryogenic temperatures

NASA Astrophysics Data System (ADS)

Holler, M.; Raabe, J.; Wepf, R.; Shahmoradian, S. H.; Diaz, A.; Sarafimov, B.; Lachat, T.; Walther, H.; Vitins, M.

2017-11-01

Nowadays ptychographic tomography in the hard x-ray regime, i.e., at energies above about 2 keV, is a well-established measurement technique. At the Paul Scherrer Institut, currently two instruments are available: one is measuring at room temperature and atmospheric pressure, and the other, the so-called OMNY (tOMography Nano crYo) instrument, is operating at ultra-high vacuum and offering cryogenic sample temperatures down to 10 K. In this manuscript, we present the sample mounts that were developed for these instruments. Aside from excellent mechanical stability and thermal conductivity, they also offer highly reproducible mounting. Various types were developed for different kinds of samples and are presented in detail, including examples of how specimens can be mounted on these holders. We also show the first hard x-ray ptychographic tomography measurements of high-pressure frozen biological samples, in the present case Chlamydomonas cells, the related sample pins and preparation steps. For completeness, we present accessories such as transportation containers for both room temperature and cryogenic samples and a gripper mechanism for automatic sample changing. The sample mounts are not limited to x-ray tomography or hard x-ray energies, and we believe that they can be very useful for other instrumentation projects.

Fabrication and Compressive Properties of Low to Medium Porosity Closed-Cell Porous Aluminum Using PMMA Space Holder Technique

PubMed Central

Jamal, Nur Ayuni; Tan, Ai Wen; Yusof, Farazila; Katsuyoshi, Kondoh; Hisashi, Imai; Singh, S.; Anuar, Hazleen

2016-01-01

In recent years, closed-cell porous Aluminum (Al) has drawn increasing attention, particularly in the applications requiring reduced weight and energy absorption capability such as in the automotive and aerospace industries. In the present work, porous Al with closed-cell structure was successfully fabricated by powder metallurgy technique using PMMA as a space holder. The effects of the amount of PMMA powder on the porosity, density, microstructure and compressive behaviors of the porous specimens were systematically evaluated. The results showed that closed-cell porous Al having different porosities (12%–32%) and densities (1.6478 g/cm3, 1.5125 g/cm3 and 1.305 g/cm3) could be produced by varying the amount of PMMA (20–30 wt %). Meanwhile, the compressive behavior results demonstrated that the plateau stress decreased and the energy absorption capacity increased with increasing amount of PMMA. However, the maximum energy absorption capacity was achieved in the closed-cell porous Al with the addition of 25 wt % PMMA. Therefore, fabrication of closed-cell porous Al using 25 wt % PMMA is considered as the optimal condition in the present study since the resultant closed-cell porous Al possessed good combinations of porosity, density and plateau stress, as well as energy absorption capacity. PMID:28773377

14 CFR 26.45 - Holders of type certificates-Alterations and repairs to alterations.

Code of Federal Regulations, 2010 CFR

2010-01-01

... AIRPLANES Aging Airplane Safety-Damage Tolerance Data for Repairs and Alterations § 26.45 Holders of type... alteration data developed by the holder of a type certificate, the holder must— (1) Review existing... Repairs Made to Alterations. For existing and future repair data developed by a holder of a type...

Flame Holder System

NASA Technical Reports Server (NTRS)

Haskin, Henry H. (Inventor); Vasquez, Peter (Inventor)

2013-01-01

A flame holder system includes a modified torch body and a ceramic flame holder. Catch pin(s) are coupled to and extend radially out from the torch body. The ceramic flame holder has groove(s) formed in its inner wall that correspond in number and positioning to the catch pin(s). Each groove starts at one end of the flame holder and can be shaped to define at least two 90.degree.turns. Each groove is sized to receive one catch pin therein when the flame holder is fitted over the end of the torch body. The flame holder is then manipulated until the catch pin(s) butt up against the end of the groove(s).

14 CFR 26.45 - Holders of type certificates-Alterations and repairs to alterations.

Code of Federal Regulations, 2012 CFR

2012-01-01

... AIRPLANES Aging Airplane Safety-Damage Tolerance Data for Repairs and Alterations § 26.45 Holders of type... alteration data developed by the holder of a type certificate, the holder must— (1) Review alteration data... Repairs Made to Alterations. For existing and future repair data developed by a holder of a type...

14 CFR 26.45 - Holders of type certificates-Alterations and repairs to alterations.

Code of Federal Regulations, 2014 CFR

2014-01-01

... AIRPLANES Aging Airplane Safety-Damage Tolerance Data for Repairs and Alterations § 26.45 Holders of type... alteration data developed by the holder of a type certificate, the holder must— (1) Review alteration data... Repairs Made to Alterations. For existing and future repair data developed by a holder of a type...

14 CFR 26.45 - Holders of type certificates-Alterations and repairs to alterations.

Code of Federal Regulations, 2013 CFR

2013-01-01

... AIRPLANES Aging Airplane Safety-Damage Tolerance Data for Repairs and Alterations § 26.45 Holders of type... alteration data developed by the holder of a type certificate, the holder must— (1) Review alteration data... Repairs Made to Alterations. For existing and future repair data developed by a holder of a type...

49 CFR 192.175 - Pipe-type and bottle-type holders.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 3 2011-10-01 2011-10-01 false Pipe-type and bottle-type holders. 192.175 Section....175 Pipe-type and bottle-type holders. (a) Each pipe-type and bottle-type holder must be designed so... equipment, that might cause corrosion or interfere with the safe operation of the holder. (b) Each pipe-type...

49 CFR 192.175 - Pipe-type and bottle-type holders.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 3 2010-10-01 2010-10-01 false Pipe-type and bottle-type holders. 192.175 Section....175 Pipe-type and bottle-type holders. (a) Each pipe-type and bottle-type holder must be designed so... equipment, that might cause corrosion or interfere with the safe operation of the holder. (b) Each pipe-type...

Characterization of plastic deformation in a disk bend test

NASA Astrophysics Data System (ADS)

Byun, T. S.; Lee, E. H.; Hunn, J. D.; Farrell, K.; Mansur, L. K.

2001-04-01

A disk bend test technique has been developed to study deformation mechanisms as well as mechanical properties. In the disk bend test, a transmission electron microscopy (TEM) disk size specimen of 3 mm diameter ×0.25 mm thick is clamped around its rim in a circular holder and indented with a tungsten carbide ball of 1 mm diameter on its back face. AISI 316LN austenitic stainless steel and 9Cr-2WVTa ferritic/martensitic steel were selected as test materials. A model was developed to determine the average plastic strain and surface plastic strain in the disk bend test. The deformation regimes of the plastic strain versus deflection curves corresponded to those of the load versus deflection curves. The stress state of the disk bend deformation was analyzed for the two test materials and compared with those of other mechanical tests such as uniaxial tensile, compact tension, and ball indentation tests. Slip line features at the deformed surface and the corresponding TEM microstructures were examined for both tensile and disk bend specimens. Differences and similarities in deformation between the disk bend and the tensile tests are described.

Advanced UXO Discrimination using Magnetometry: Understanding Remanent Magnetization

DTIC Science & Technology

2009-09-01

moments of steel samples. The MRIP comprises six three-component fluxgate magnetometers symmetrically distributed around a rotating sample holder. Samples...comprises six three- component fluxgate magnetometers symmetrically distributed around a rotating sample holder. Samples are placed on the holder... fluxgate magnetometers symmetrically distributed around a rotating sample holder. Samples are placed on the holder and are slowly spun through two

3D printing scanning electron microscopy sample holders: A quick and cost effective alternative for custom holder fabrication.

PubMed

Meloni, Gabriel N; Bertotti, Mauro

2017-01-01

A simple and cost effective alternative for fabricating custom Scanning Electron Microscope (SEM) sample holders using 3D printers and conductive polylactic acid filament is presented. The flexibility of the 3D printing process allowed for the fabrication of sample holders with specific features that enable the high-resolution imaging of nanoelectrodes and nanopipettes. The precise value of the inner semi cone angle of the nanopipettes taper was extracted from the acquired images and used for calculating their radius using electrochemical methods. Because of the low electrical resistivity presented by the 3D printed holder, the imaging of non-conductive nanomaterials, such as alumina powder, was found to be possible. The fabrication time for each sample holder was under 30 minutes and the average cost was less than $0.50 per piece. Despite being quick and economical to fabricate, the sample holders were found to be sufficiently resistant, allowing for multiple uses of the same holder.

3D printing scanning electron microscopy sample holders: A quick and cost effective alternative for custom holder fabrication

PubMed Central

Bertotti, Mauro

2017-01-01

A simple and cost effective alternative for fabricating custom Scanning Electron Microscope (SEM) sample holders using 3D printers and conductive polylactic acid filament is presented. The flexibility of the 3D printing process allowed for the fabrication of sample holders with specific features that enable the high-resolution imaging of nanoelectrodes and nanopipettes. The precise value of the inner semi cone angle of the nanopipettes taper was extracted from the acquired images and used for calculating their radius using electrochemical methods. Because of the low electrical resistivity presented by the 3D printed holder, the imaging of non-conductive nanomaterials, such as alumina powder, was found to be possible. The fabrication time for each sample holder was under 30 minutes and the average cost was less than $0.50 per piece. Despite being quick and economical to fabricate, the sample holders were found to be sufficiently resistant, allowing for multiple uses of the same holder. PMID:28753638

Calculation of recirculating flow behind flame-holders

NASA Astrophysics Data System (ADS)

Zeng, Q.; Sheng, Y.; Zhou, Q.

1985-10-01

Adoptability of standard K-epsilon turbulence model for numerical calculation of recirculating flow is discussed. Many computations of recirculating flows behind bluff-bodies used as flame-holders in afterburner of aeroengine have been completed. Blocking-off method to treat the incline walls of the flame-holder gives good results. In isothermal recirculating flows the flame-holder wall is assumed to be isolated. Therefore, it is possible to remove the inactive zone from the calculation domain in programming to save computer time. The computation for a V-shaped flame-holder exhibits an interesting phenomenon that the recirculation zone extends to the cavity of the flame-holder.

Molten metal injector system and method

DOEpatents

Meyer, Thomas N.; Kinosz, Michael J.; Bigler, Nicolas; Arnaud, Guy

2003-04-01

Disclosed is a molten metal injector system including a holder furnace, a casting mold supported above the holder furnace, and a molten metal injector supported from a bottom side of the mold. The holder furnace contains a supply of molten metal having a metal oxide film surface. The bottom side of the mold faces the holder furnace. The mold defines a mold cavity for receiving the molten metal from the holder furnace. The injector projects into the holder furnace and is in fluid communication with the mold cavity. The injector includes a piston positioned within a piston cavity defined by a cylinder for pumping the molten metal upward from the holder furnace and injecting the molten metal into the mold cavity under pressure. The piston and cylinder are at least partially submerged in the molten metal when the holder furnace contains the molten metal. The cylinder further includes a molten metal intake for receiving the molten metal into the piston cavity. The molten metal intake is located below the metal oxide film surface of the molten metal when the holder furnace contains the molten metal. A method of injecting molten metal into a mold cavity of a casting mold is also disclosed.

Manipulator for rotating and translating a sample holder

DOEpatents

van de Water, Jeroen [Breugel, NL; van den Oetelaar, Johannes [Eindhoven, NL; Wagner, Raymond [Gorinchem, NL; Slingerland, Hendrik Nicolaas [Venlo, NL; Bruggers, Jan Willem [Eindhoven, NL; Ottevanger, Adriaan Huibert Dirk [Malden, NL; Schmid, Andreas [Berkeley, CA; Olson, Eric A [Champaign, IL; Petrov, Ivan G [Champaign, IL; Donchev, Todor I [Urbana, IL; Duden, Thomas [Kensington, CA

2011-02-08

A manipulator for use in e.g. a Transmission Electron Microscope (TEM) is described, said manipulator capable of rotating and translating a sample holder (4). The manipulator clasps the round sample holder between two members (3A, 3B), said members mounted on actuators (2A, 2B). Moving the actuators in the same direction results in a translation of the sample holder, while moving the actuators in opposite directions results in a rotation of the sample holder.

24 CFR 290.19 - Restrictions concerning nondiscrimination against Section 8 certificate holders and voucher holders.

Code of Federal Regulations, 2011 CFR

2011-04-01

... PROPERTIES DISPOSITION OF MULTIFAMILY PROJECTS AND SALE OF HUD-HELD MULTIFAMILY MORTGAGES Disposition of Multifamily Projects § 290.19 Restrictions concerning nondiscrimination against Section 8 certificate holders and voucher holders. The purchaser of any multifamily housing project shall not refuse unreasonably to...

24 CFR 290.19 - Restrictions concerning nondiscrimination against Section 8 certificate holders and voucher holders.

Code of Federal Regulations, 2014 CFR

2014-04-01

... PROPERTIES DISPOSITION OF MULTIFAMILY PROJECTS AND SALE OF HUD-HELD MULTIFAMILY MORTGAGES Disposition of Multifamily Projects § 290.19 Restrictions concerning nondiscrimination against Section 8 certificate holders and voucher holders. The purchaser of any multifamily housing project shall not refuse unreasonably to...

24 CFR 290.19 - Restrictions concerning nondiscrimination against Section 8 certificate holders and voucher holders.

Code of Federal Regulations, 2010 CFR

2010-04-01

... PROPERTIES DISPOSITION OF MULTIFAMILY PROJECTS AND SALE OF HUD-HELD MULTIFAMILY MORTGAGES Disposition of Multifamily Projects § 290.19 Restrictions concerning nondiscrimination against Section 8 certificate holders and voucher holders. The purchaser of any multifamily housing project shall not refuse unreasonably to...

24 CFR 290.19 - Restrictions concerning nondiscrimination against Section 8 certificate holders and voucher holders.

Code of Federal Regulations, 2012 CFR

2012-04-01

... PROPERTIES DISPOSITION OF MULTIFAMILY PROJECTS AND SALE OF HUD-HELD MULTIFAMILY MORTGAGES Disposition of Multifamily Projects § 290.19 Restrictions concerning nondiscrimination against Section 8 certificate holders and voucher holders. The purchaser of any multifamily housing project shall not refuse unreasonably to...

39 CFR 3001.9 - Filing of documents.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Commission, or by direction of the presiding officer, shall be made using the Internet (Filing Online... using Filing Online, it must be submitted to the Commission by a principal account holder or an agent account holder (Filing Online account holder). The authority of the principal account holder to represent...

39 CFR 3001.9 - Filing of documents.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Commission, or by direction of the presiding officer shall be made using the Internet (Filing Online...) Account holder. In order for a document to be accepted using Filing Online, it must be submitted to the Commission by a principal account holder or an agent account holder (Filing Online account holder). The...

39 CFR 3001.9 - Filing of documents.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Commission, or by direction of the presiding officer, shall be made using the Internet (Filing Online... accepted using Filing Online, it must be submitted to the Commission by a principal account holder or an agent account holder (Filing Online account holder). The authority of the principal account holder to...

39 CFR 3001.9 - Filing of documents.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Commission, or by direction of the presiding officer, shall be made using the Internet (Filing Online... accepted using Filing Online, it must be submitted to the Commission by a principal account holder or an agent account holder (Filing Online account holder). The authority of the principal account holder to...

Porous coolant tube holder for fuel cell stack

DOEpatents

Guthrie, Robin J.

1981-01-01

A coolant tube holder for a stack of fuel cells is a gas porous sheet of fibrous material adapted to be sandwiched between a cell electrode and a nonporous, gas impervious flat plate which separates adjacent cells. The porous holder has channels in one surface with coolant tubes disposed therein for carrying coolant through the stack. The gas impervious plate is preferably bonded to the opposite surface of the holder, and the channel depth is the full thickness of the holder.

DIY Tomography sample holder

NASA Astrophysics Data System (ADS)

Lari, L.; Wright, I.; Boyes, E. D.

2015-10-01

A very simple tomography sample holder at minimal cost was developed in-house. The holder is based on a JEOL single tilt fast exchange sample holder where its exchangeable tip was modified to allow high angle degree tilt. The shape of the tip was designed to retain mechanical stability while minimising the lateral size of the tip. The sample can be mounted on as for a standard 3mm Cu grids as well as semi-circular grids from FIB sample preparation. Applications of the holder on different sample systems are shown.

Note: Rigid holder to host and bend a crystal for multiple volume reflection of a particle beam

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carassiti, V.; Melchiorri, M.; Dalpiaz, P.

2010-06-15

A holder to lodge and bend a silicon crystal to excite multivolume reflection of a high-energy particle beam has been designed and fabricated. A mechanically robust and stable structure fastens a crystal at best condition for experiments. The holder has allowed the observation of 12-time repeated volume reflection with very high efficiency. We detail the most important features behind the construction of the holder together with the characterization of the crystal being bent by the holder.

Lexan Linear Shaped Charge Holder with Magnets and Backing Plate

NASA Technical Reports Server (NTRS)

Maples, Matthew W.; Dutton, Maureen L.; Hacker, Scott C.; Dean, Richard J.; Kidd, Nicholas; Long, Chris; Hicks, Robert C.

2013-01-01

A method was developed for cutting a fabric structural member in an inflatable module, without damaging the internal structure of the module, using linear shaped charge. Lexan and magnets are used in a charge holder to precisely position the linear shaped charge over the desired cut area. Two types of charge holders have been designed, each with its own backing plate. One holder cuts fabric straps in the vertical configuration, and the other charge holder cuts fabric straps in the horizontal configuration.

A simple and inclusive method to determine the habit plane in transmission electron microscope based on accurate measurement of foil thickness

DOE Office of Scientific and Technical Information (OSTI.GOV)

Qiu, Dong, E-mail: d.qiu@uq.edu.au; Zhang, Mingxing

2014-08-15

A simple and inclusive method is proposed for accurate determination of the habit plane between bicrystals in transmission electron microscope. Whilst this method can be regarded as a variant of surface trace analysis, the major innovation lies in the improved accuracy and efficiency of foil thickness measurement, which involves a simple tilt of the thin foil about a permanent tilting axis of the specimen holder, rather than cumbersome tilt about the surface trace of the habit plane. Experimental study has been done to validate this proposed method in determining the habit plane between lamellar α{sub 2} plates and γ matrixmore » in a Ti–Al–Nb alloy. Both high accuracy (± 1°) and high precision (± 1°) have been achieved by using the new method. The source of the experimental errors as well as the applicability of this method is discussed. Some tips to minimise the experimental errors are also suggested. - Highlights: • An improved algorithm is formulated to measure the foil thickness. • Habit plane can be determined with a single tilt holder based on the new algorithm. • Better accuracy and precision within ± 1° are achievable using the proposed method. • The data for multi-facet determination can be collected simultaneously.« less

Sample holder with optical features

DOEpatents

Milas, Mirko; Zhu, Yimei; Rameau, Jonathan David

2013-07-30

A sample holder for holding a sample to be observed for research purposes, particularly in a transmission electron microscope (TEM), generally includes an external alignment part for directing a light beam in a predetermined beam direction, a sample holder body in optical communication with the external alignment part and a sample support member disposed at a distal end of the sample holder body opposite the external alignment part for holding a sample to be analyzed. The sample holder body defines an internal conduit for the light beam and the sample support member includes a light beam positioner for directing the light beam between the sample holder body and the sample held by the sample support member.

Transmission electron microscope sample holder with optical features

DOEpatents

Milas, Mirko [Port Jefferson, NY; Zhu, Yimei [Stony Brook, NY; Rameau, Jonathan David [Coram, NY

2012-03-27

A sample holder for holding a sample to be observed for research purposes, particularly in a transmission electron microscope (TEM), generally includes an external alignment part for directing a light beam in a predetermined beam direction, a sample holder body in optical communication with the external alignment part and a sample support member disposed at a distal end of the sample holder body opposite the external alignment part for holding a sample to be analyzed. The sample holder body defines an internal conduit for the light beam and the sample support member includes a light beam positioner for directing the light beam between the sample holder body and the sample held by the sample support member.

21 CFR 870.3935 - Prosthetic heart valve holder.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Prosthetic heart valve holder. 870.3935 Section... heart valve holder. (a) Identification. A prosthetic heart valve holder is a device used to hold a replacement heart valve while it is being sutured into place. (b) Classification. Class I. The device is...

77 FR 69650 - Agency Information Collection Activities: Holders or Containers Which Enter the United States...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-20

... Activities: Holders or Containers Which Enter the United States Duty Free AGENCY: U.S. Customs and Border... information collection requirement concerning the Holders or Containers which Enter the United States Duty... concerning the following information collection: Title: Holders or Containers which Enter the United States...

78 FR 44957 - Agency Information Collection Activities: BioWatch Filter Holder Log, Filter Holder Log DHS Form...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-25

... DEPARTMENT OF HOMELAND SECURITY Agency Information Collection Activities: BioWatch Filter Holder Log, Filter Holder Log DHS Form 9500 AGENCY: Office of Health Affairs, DHS. ACTION: 60-Day Notice and....: Daniel Yereb, [email protected] 703- 647-8052. SUPPLEMENTARY INFORMATION: Following collection, the filter...

10 CFR 1016.5 - Submission of procedures by access permit holder.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 4 2011-01-01 2011-01-01 false Submission of procedures by access permit holder. 1016.5 Section 1016.5 Energy DEPARTMENT OF ENERGY (GENERAL PROVISIONS) SAFEGUARDING OF RESTRICTED DATA General Provisions § 1016.5 Submission of procedures by access permit holder. No access permit holder shall have...

10 CFR 1016.5 - Submission of procedures by access permit holder.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 4 2010-01-01 2010-01-01 false Submission of procedures by access permit holder. 1016.5 Section 1016.5 Energy DEPARTMENT OF ENERGY (GENERAL PROVISIONS) SAFEGUARDING OF RESTRICTED DATA General Provisions § 1016.5 Submission of procedures by access permit holder. No access permit holder shall have...

21 CFR 882.4460 - Neurosurgical head holder (skull clamp).

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Neurosurgical head holder (skull clamp). 882.4460... holder (skull clamp). (a) Identification. A neurosurgical head holder (skull clamp) is a device used to clamp the patient's skull to hold head and neck in a particular position during surgical procedures. (b...

21 CFR 870.3935 - Prosthetic heart valve holder.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Prosthetic heart valve holder. 870.3935 Section... heart valve holder. (a) Identification. A prosthetic heart valve holder is a device used to hold a replacement heart valve while it is being sutured into place. (b) Classification. Class I. The device is...

21 CFR 870.3935 - Prosthetic heart valve holder.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Prosthetic heart valve holder. 870.3935 Section... heart valve holder. (a) Identification. A prosthetic heart valve holder is a device used to hold a replacement heart valve while it is being sutured into place. (b) Classification. Class I. The device is...

21 CFR 870.3935 - Prosthetic heart valve holder.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Prosthetic heart valve holder. 870.3935 Section... heart valve holder. (a) Identification. A prosthetic heart valve holder is a device used to hold a replacement heart valve while it is being sutured into place. (b) Classification. Class I. The device is...

21 CFR 870.3935 - Prosthetic heart valve holder.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Prosthetic heart valve holder. 870.3935 Section... heart valve holder. (a) Identification. A prosthetic heart valve holder is a device used to hold a replacement heart valve while it is being sutured into place. (b) Classification. Class I. The device is...

Tool holder for preparation and inspection of a radiused edge cutting tool

DOEpatents

Asmanes, Charles

1979-01-01

A tool holding fixture is provided for removably holding a radiused edge cutting tool in a tool edge lapping apparatus. The fixture allows the operator to preset the lapping radius and angle before the tool holder is placed in the fixture and the holder may be removed from the lapping apparatus to inspect the tool and simply replaced in the fixture to continue lapping in accordance with a precise alignment without realignment of the tool relative to the lap. The tool holder includes a pair of self aligning bearings in the form of precision formed steel balls connected together by a rigid shaft. The tool is held by an arm extending from the shaft and the balls set in fixed position bearing cups and the holder is oscillated back and forth about a fixed axis of rotation to lap the tool radius by means of a reversibly driven belt-pulley arrangement coupled to the shaft between the bearings. To temporarily remove the holder, the drive belt is slipped over the rearward end of the holder and the holder is lifted out of the bearing cups.

Ergonomic design and evaluation of a diagnostic ultrasound transducer holder.

PubMed

Ghasemi, Mohamad Sadegh; Hosseinzadeh, Payam; Zamani, Farhad; Ahmadpoor, Hossein; Dehghan, Naser

2017-12-01

Work-related musculoskeletal disorders (WMSDs) are injuries and disorders that affect the body's movement and musculoskeletal system. Awkward postures represent one of the major ergonomic risk factors that cause WMSDs among sonographers while working with an ultrasound transducer. This study aimed to design and evaluate a new holder for the ultrasound transducer. In the first phase a new holder was designed for the transducer, considering design principles. Evaluation of the new holder was then carried out by electrogoniometry and a locally perceived discomfort (LPD) scale. The application of design principles to the new holder resulted in an improvement of wrist posture and comfort. Wrist angles in extension, flexion, radial deviation and ulnar deviation were lower with utilization of the new holder. The severity of discomfort based on the LPD method in the two modes of work with and without the new holder was reported with values of 1.3 and 1.8, respectively (p < 0.05). Overall, this study indicated that applying ergonomics design principles was effective in minimizing wrist deviation and increasing comfort while working with the new holder.

Off-axis reflective optical apparatus

NASA Technical Reports Server (NTRS)

Ames, Lawrence L. (Inventor); Leary, David F. (Inventor); Mammini, Paul V. (Inventor)

2005-01-01

Embodiments of the present invention are directed to a simple apparatus and a convenient and accurate method of mounting the components to form an off-axis reflective optical apparatus such as a collimator. In one embodiment, an off-axis reflective optical apparatus comprises a mounting block having a ferrule holder support surface and an off-axis reflector support surface which is generally perpendicular to the ferrule holder support surface. An optical reflector is mounted on the off-axis reflector support surface and has a reflected beam centerline. The optical reflector has a conic reflective surface and a conic center. A ferrule holder is mounted on the ferrule holder support surface. The ferrule holder provides a ferrule for coupling to an optical fiber and orienting a fiber tip of the optical fiber along a fiber axis toward the optical reflector. The fiber axis is nonparallel to the reflected beam centerline. Prior to mounting the optical reflector to the off-axis reflector support surface and prior to mounting the ferrule holder to the ferrule holder support surface, the optical reflector is movable on the off-axis reflector surface and the ferrule holder is movable on the ferrule holder support surface to align the conic center of the optical reflector with respect to the fiber tip of the optical fiber, and the apparatus has at least one of the following features: (1) the optical reflector is movable on the off-axis reflector support surface to adjust a focus of the fiber tip with respect to the optical reflector, and (2) the ferrule holder is movable on the ferrule holder support surface to adjust the focus of the fiber tip with respect to the optical reflector.

27 CFR 70.147 - Priority of interest and expenses.

Code of Federal Regulations, 2010 CFR

2010-04-01

... interest is not subrogated to the rights of the holder of the State sales tax lien. However, if the holder... the rights of the holder of the sales tax lien, the holder of the lien or security interest will also... Collection of Excise and Special (Occupational) Tax Lien for Taxes § 70.147 Priority of interest and expenses...

21 CFR 872.1905 - Dental x-ray film holder.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Dental x-ray film holder. 872.1905 Section 872...) MEDICAL DEVICES DENTAL DEVICES Diagnostic Devices § 872.1905 Dental x-ray film holder. (a) Identification. A dental x-ray film holder is a device intended to position and to hold x-ray film inside the mouth...

21 CFR 872.1905 - Dental x-ray film holder.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Dental x-ray film holder. 872.1905 Section 872...) MEDICAL DEVICES DENTAL DEVICES Diagnostic Devices § 872.1905 Dental x-ray film holder. (a) Identification. A dental x-ray film holder is a device intended to position and to hold x-ray film inside the mouth...

21 CFR 872.1905 - Dental x-ray film holder.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Dental x-ray film holder. 872.1905 Section 872...) MEDICAL DEVICES DENTAL DEVICES Diagnostic Devices § 872.1905 Dental x-ray film holder. (a) Identification. A dental x-ray film holder is a device intended to position and to hold x-ray film inside the mouth...

21 CFR 872.1905 - Dental x-ray film holder.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Dental x-ray film holder. 872.1905 Section 872...) MEDICAL DEVICES DENTAL DEVICES Diagnostic Devices § 872.1905 Dental x-ray film holder. (a) Identification. A dental x-ray film holder is a device intended to position and to hold x-ray film inside the mouth...

21 CFR 872.1905 - Dental x-ray film holder.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Dental x-ray film holder. 872.1905 Section 872...) MEDICAL DEVICES DENTAL DEVICES Diagnostic Devices § 872.1905 Dental x-ray film holder. (a) Identification. A dental x-ray film holder is a device intended to position and to hold x-ray film inside the mouth...

30 CFR 250.1010 - General requirements for pipeline right-of-way holders.

Code of Federal Regulations, 2010 CFR

2010-07-01

... United States or its lessees or right-of-way holders, as the case may be, the full value of all damages...). The right-of-way holder shall make available all records relative to the design, construction... site. Furthermore, the holder is responsible for accidents or damages which might occur as a result of...

Observation of three-dimensional elemental distributions of a Si device using a 360 degrees -tilt FIB and the cold field-emission STEM system.

PubMed

Yaguchi, Toshie; Konno, Mitsuru; Kamino, Takeo; Watanabe, Masashi

2008-11-01

A technique for preparation of a pillar-shaped specimen and its multidirectional observation using a combination of a scanning transmission electron microscope (STEM) and a focused ion beam (FIB) instrument has been developed. The system employs an FIB/STEM compatible holder with a specially designed tilt mechanism, which allows the specimen to be tilted through 360 degrees [T. Yaguchi, M. Konno, T. Kamino, T. Hashimoto, T. Ohnishi, K. Umemura, K. Asayama, Microsc. Microanal. 9 (Suppl. 2) (2003) 118; T. Yaguchi, M. Konno, T. Kamino, T. Hashimoto, T. Ohnishi, M. Watanabe, Microsc. Microanal. 10 (Suppl. 2) (2004) 1030]. This technique was applied to obtain the three-dimensional (3D) elemental distributions around a contact plug of a Si device used in a 90-nm technology. A specimen containing only one contact plug was prepared in the shape of a pillar with a diameter of 200nm and a length of 5mum. Elemental maps were obtained from the pillar specimen using a 200-kV cold-field emission gun (FEG) STEM model HD-2300C equipped with the EDAX genesis X-ray energy-dispersive spectrometry (XEDS) system through a spectrum imaging technique. In this study, elemental distributions of minor elements with weak signals were enhanced by applying principal component analysis (PCA), which is a superior technique to extract weak signals from a large dataset. The distributions of elements, especially the metallization component Ti and minor dopant As in this particular device, were successfully extracted by PCA. Finally, the 3D elemental distributions around the contact plug could be visualized by reconstruction from the tilt series of maps.

Evaluation of metal bond strength to dentin and enamel using different adhesives and surface treatments.

PubMed

Dundar, Mine; Gungor, Mehmet Ali; Cal, Ebru; Darcan, Alev; Erdem, Adalet

2007-01-01

Because adherence of base metal alloys is important for the long-term clinical success of adhesive fixed partial dentures, it has been necessary to improve adhesion to metal substrate by using different surface treatments. This study used different surface conditioning methods and two different luting resins to evaluate the shear bond strength of base metal alloys to dentin and enamel. Sixty noncarious freshly extracted human teeth were mounted in a plastic holder filled with autopolymerized acrylic resin. After the roots were removed and 30 flat enamel and 30 flat dentin surfaces were exposed, the specimens were divided randomly into two main luting cement groups. Sixty nickel chromium (NiCr) metal specimens were fabricated and subjected to three different surface conditioning procedures: sandblasting with 50 microm aluminum oxide, tribochemical silica coating, and a combination of the two. Scanning electron mircoscopy (SEM) evaluations revealed mainly cohesive failures. Self-cure adhesive resulted in higher bond strengths to dental substrates. Higher bond strengths were achieved through a combination of sandblasting and tribochemical silica coating; however, further clinical research is required. A surface treatment that combines sandblasting with tribochemical silica coating can achieve a more effective bond for adhesive restorations with metal substrates.

Position of document holder and work related risk factors for neck pain among computer users: a narrative review.

PubMed

Ambusam, S; Baharudin, O; Roslizawati, N; Leonard, J

2015-01-01

Document holder is used as a remedy to address occupational neck pain among computer users. An understanding on the effects of the document holder along with other work related risk factors while working in computer workstation requires attention. A comprehensive knowledge on the optimal location of the document holder in computer use and associated work related factors that may contribute to neck pain reviewed in this article. A literature search has been conducted over the past 14 years based on the published articles from January 1990 to January 2014 in both Science Direct and PubMed databases. Medical Subject Headings (MeSH) keywords for search were neck muscle OR head posture OR muscle tension' OR muscle activity OR work related disorders OR neck pain AND/OR document location OR document holder OR source document OR copy screen holder.Document holder placed lateral to the screen was most preferred to reduce neck discomfort among occupational typists. Document without a holder was placed flat on the surface is least preferred. The head posture and muscle activity increases when the document is placed flat on the surface compared to when placed on the document holder. Work related factors such as static posture, repetitive movement, prolong sitting and awkward positions were the risk factors for chronic neck pain. This review highlights the optimal location for document holder for computer users to reduce neck pain. Together, the importance of work related risk factors for to neck pain on occupational typist is emphasized for the clinical management.

17 CFR 240.14a-7 - Obligations of registrants to provide a list of, or mail soliciting material to, security holders.

Code of Federal Regulations, 2010 CFR

2010-04-01

..., form of proxy or other communication to such holders, including to the extent known or reasonably... provided for under applicable state law identifying the proposal or other corporate action that will be the subject of the security holder's solicitation or communication and attesting that: (i) The security holder...

42 CFR 60.53 - Notification to lender or holder of change in enrollment status.

Code of Federal Regulations, 2010 CFR

2010-10-01

... different), the student's Social Security number, the date of the change in the enrollment status, or... 42 Public Health 1 2010-10-01 2010-10-01 false Notification to lender or holder of change in... holder of change in enrollment status. Each school must notify the holder of a HEAL loan of any change in...

SEM technique for imaging and measuring electronic transport in nanocomposites based on electric field induced contrast

DOEpatents

Jesse, Stephen [Knoxville, TN; Geohegan, David B [Knoxville, TN; Guillorn, Michael [Brooktondale, NY

2009-02-17

Methods and apparatus are described for SEM imaging and measuring electronic transport in nanocomposites based on electric field induced contrast. A method includes mounting a sample onto a sample holder, the sample including a sample material; wire bonding leads from the sample holder onto the sample; placing the sample holder in a vacuum chamber of a scanning electron microscope; connecting leads from the sample holder to a power source located outside the vacuum chamber; controlling secondary electron emission from the sample by applying a predetermined voltage to the sample through the leads; and generating an image of the secondary electron emission from the sample. An apparatus includes a sample holder for a scanning electron microscope having an electrical interconnect and leads on top of the sample holder electrically connected to the electrical interconnect; a power source and a controller connected to the electrical interconnect for applying voltage to the sample holder to control the secondary electron emission from a sample mounted on the sample holder; and a computer coupled to a secondary electron detector to generate images of the secondary electron emission from the sample.

Reducing the Effect of Transducer Mount Induced Noise on Aeroacoustic Wind Tunnel Testing Data with a New Transducer Mount Design

NASA Technical Reports Server (NTRS)

Herron, A. J.; Reed, D. K.; Nance, D. K.

2015-01-01

Characterization of launch vehicle unsteady aerodynamics is a field best studied through experimentation, which is often carried out in the form of large scale wind tunnel testing. Measurement of the fluctuating pressures induced by the boundary layer noise is customarily made with miniature pressure transducers installed into a model of the vehicle of interest. Literature shows that noise level increases between two to five decibels (dB referenced to 20 micropascal) can be induced when the transducer surface is not mounted perfectly flush with the model outer surface. To reduce this artificially induced noise, special transducer holders have been used for aeroacoustic wind tunnel testing by NASA. This holder is a sleeve into which the transducer fits, with a cap that allows it to be mounted in a recessed hole in the model. A single hole in the holder allows the transport of the tunnel medium so the transducer can discriminate the fluctuating pressure due to the turbulent boundary layer noise. The holder is first dry fitted into the model and any difference in height between the holder and the model surface can be sanded flush. The holder is then removed from the model, the transducer glued inside the holder, and the holder replaced in the model, secured also with glue, thus eliminating the problem of noise level increases due to lack of flushness. In order to work with this holder design, special transducers have been ordered with their standard screen removed and the diaphragm moved as close to the top of the casing as possible to minimize any cavity volume. Although this greatly reduces induced noise due to the transducers being out of flush, the holders can also induce a cavity resonance that is usually at a very high frequency. This noise is termed transducer mount induced noise (XMIN). The peak of the mode can vary with the cavity depth, boundary layer noise that can excite the mode, tunnel flow medium, and the build of the transducers. Because the boundary layer flow interaction with the microphone holder seems to have some effect on the cavity resonance response, the NASA/Marshall Space Flight Center (MSFC) aeroacoustic team postulated that changing the design of the holder might reduce the cavity resonance response. An experiment was performed at the MSFC Trisonic Wind Tunnel comparing a new holder design with the traditional MSFC holder. The new holder design is intended to mimic the Kulite Semiconductors, Inc. B-screen, where the single hole of the traditional MSFC holder is replaced by a series of ten 0.007 inch diameter holes. This particular design serves to protect the transducer diaphragm as in the manufacturer's B-screen, but also increases the frequency of the XMIN such that it is not apparent in the data collected from aeroacoustic wind tunnel tests. MSFC compared the two holder designs by installing two transducers in standard holders on one side of a ten inch long ten degree cone, and two transducers in B-screen holders on the opposite side for a series of runs at different conditions. Over 11-13 February, 2013, the model was run at Mach numbers between 0.80 and 1.96 at angles of attack at 0 deg, plus or minus 1 deg, plus or minus 2 deg, plus or minus 4 deg, and plus or minus 8 deg. Model roll attitudes at 0 deg, 90 deg, and 180 deg were tested to isolate potential tunnel bias. This paper presents results from the test showing that the proposed holder design significantly reduces the influence of XMIN on measured fluctuating pressure levels.

Development of a New Rain Erosion Test Method

NASA Astrophysics Data System (ADS)

Chung, Dong-Teak; Kang, Hyung; Jin, Doo-Han

The nose of a missile, flying through raining region with a supersonic speed, is subjected to the rain erosion because the nose is made of a brittle ceramic material. Various test methods are used to address such a phenomenon. However, most of the methods are expensive and/or require complicated facilities. The simple yet very effective rain erosion test method is developed. It consists of (1) a low pressure air gun, (2) a sabot assembly for launching single rain drop, (3) a stopper, and (4) a specimen holder block. The sabot assembly similar to the hypodermic syringe carries specific amount of water toward the stopper launched by the low pressure air gun. When the impact occurs against the stopper which stops the sabot, the water and the steel plunger (at the back of the sabot) continues pushing the sabot to generate a high pressure in the chamber filled with resilient silicon rubber. The pressurized silicon rubber then is squeezed through the small opening in front of the sabot, thus, accelerates the water droplet to a much higher velocity. The velocity of the droplet is measured by the make-screen method, where there are two aluminum foils with an insulating layer in between. The droplet velocity up to 800 m/s is successfully attained using a low pressure air compressor. The specimen made of a ceramic material is placed in front of the high speed water droplet and the rain erosion damage on the surface of the specimen is observed.

48 CFR 339.7001 - Request for approval to make an award to other than a GSA BPA holder.

Code of Federal Regulations, 2010 CFR

2010-10-01

... make an award to other than a GSA BPA holder. 339.7001 Section 339.7001 Federal Acquisition Regulations... Services 339.7001 Request for approval to make an award to other than a GSA BPA holder. The Contracting... micro-purchase threshold, that obtaining the required services from a source other than a GSA BPA holder...

48 CFR 339.7001 - Request for approval to make an award to other than a GSA BPA holder.

Code of Federal Regulations, 2014 CFR

2014-10-01

... make an award to other than a GSA BPA holder. 339.7001 Section 339.7001 Federal Acquisition Regulations... Services 339.7001 Request for approval to make an award to other than a GSA BPA holder. The Contracting... micro-purchase threshold, that obtaining the required services from a source other than a GSA BPA holder...

48 CFR 339.7001 - Request for approval to make an award to other than a GSA BPA holder.

Code of Federal Regulations, 2011 CFR

2011-10-01

... make an award to other than a GSA BPA holder. 339.7001 Section 339.7001 Federal Acquisition Regulations... Services 339.7001 Request for approval to make an award to other than a GSA BPA holder. The Contracting... micro-purchase threshold, that obtaining the required services from a source other than a GSA BPA holder...

48 CFR 339.7001 - Request for approval to make an award to other than a GSA BPA holder.

Code of Federal Regulations, 2012 CFR

2012-10-01

... make an award to other than a GSA BPA holder. 339.7001 Section 339.7001 Federal Acquisition Regulations... Services 339.7001 Request for approval to make an award to other than a GSA BPA holder. The Contracting... micro-purchase threshold, that obtaining the required services from a source other than a GSA BPA holder...

48 CFR 339.7001 - Request for approval to make an award to other than a GSA BPA holder.

Code of Federal Regulations, 2013 CFR

2013-10-01

... make an award to other than a GSA BPA holder. 339.7001 Section 339.7001 Federal Acquisition Regulations... Services 339.7001 Request for approval to make an award to other than a GSA BPA holder. The Contracting... micro-purchase threshold, that obtaining the required services from a source other than a GSA BPA holder...

19 CFR 134.23 - Containers or holders designed for or capable of reuse.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 19 Customs Duties 1 2011-04-01 2011-04-01 false Containers or holders designed for or capable of reuse. 134.23 Section 134.23 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY COUNTRY OF ORIGIN MARKING Marking of Containers or Holders § 134.23 Containers or holders designed for or...

19 CFR 134.25 - Containers or holders for repacked J-list articles and articles incapable of being marked.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 19 Customs Duties 1 2010-04-01 2010-04-01 false Containers or holders for repacked J-list articles... Containers or Holders § 134.25 Containers or holders for repacked J-list articles and articles incapable of...—Repacked J-List Articles and Articles Incapable of Being Marked (Port of entry) I,of, certify that if the...

30 CFR 285.114 - Paperwork Reduction Act statements-information collection.

Code of Federal Regulations, 2010 CFR

2010-07-01

... OFFSHORE RENEWABLE ENERGY ALTERNATE USES OF EXISTING FACILITIES ON THE OUTER CONTINENTAL SHELF General... renewable energy applicants, lessees, ROW grant holders, RUE grant holders, Alternate Use RUE grant holders...

Solid-state-laser-rod holder

DOEpatents

Gettemy, D.J.; Barnes, N.P.; Griggs, J.E.

1981-08-11

The disclosure relates to a solid state laser rod holder comprising Invar, copper tubing, and epoxy joints. Materials and coefficients of expansion of the components of the holder combine with the rod to produce a joint which will give before the rod itself will. The rod may be lased at about 70 to 80/sup 0/K and returned from such a temperature to room temperature repeatedly without its or the holder's destruction.

Preset pivotal tool holder

DOEpatents

Asmanes, Charles

1979-01-01

A tool fixture is provided for precise pre-alignment of a radiused edge cutting tool in a tool holder relative to a fixed reference pivot point established on said holder about which the tool holder may be selectively pivoted relative to the fixture base member to change the contact point of the tool cutting edge with a workpiece while maintaining the precise same tool cutting radius relative to the reference pivot point.

Magnetically-induced solid-phase microextraction fiber actuation system for quantitative headspace and liquid sampling

DOEpatents

Harvey, Chris; Carter, Jerry; Chambers, David M.

2017-05-23

A magnetically-induced SPME fiber actuation system includes a SPME fiber holder and a SPME fiber holder actuator, for holding and magnetically actuating a SPME fiber assembly. The SPME fiber holder has a plunger with a magnetic material to which the SPME fiber assembly is connected, and the magnetic SPME fiber holder actuator has an elongated barrel with a loading chamber for receiving the SPME fiber assembly-connected SPME fiber holder, and an external magnet which induces axial motion of the magnetic material of the plunger to extend/retract the SPME fiber from/into the protective needle of the SPME fiber assembly.

Highly identified power-holders feel responsible: The interplay between social identification and social power within groups.

PubMed

Scholl, Annika; Sassenberg, Kai; Ellemers, Naomi; Scheepers, Daan; de Wit, Frank

2018-01-01

Power relations affect dynamics within groups. Power-holders' decisions not only determine their personal outcomes, but also the outcomes of others in the group that they control. Yet, power-holders often tend to overlook this responsibility to take care of collective interests. The present research investigated how social identification - with the group to which both the powerful and the powerless belong - alters perceived responsibility among power-holders (and the powerless). Combining research on social power and social identity, we argue that power-holders perceive more responsibility than the powerless when strongly (rather than when weakly) identifying with the group. A study among leaders and an experiment supported this, highlighting that although power-holders are often primarily concerned about personal outcomes, they do feel responsible for considering others' interests when these others are included in the (social) self. © 2017 The British Psychological Society.

Casting Apparatus Including A Gas Driven Molten Metal Injector And Method

DOEpatents

Trudel, David R.; Meyer, Thomas N.; Kinosz, Michael J.; Arnaud, Guy; Bigler, Nicolas

2003-06-17

The filtering molten metal injector system includes a holder furnace, a casting mold supported above the holder furnace, and at least one molten metal injector supported from a bottom side of the casting mold. The holder furnace contains a supply of molten metal. The mold defines a mold cavity for receiving the molten metal from the holder furnace. The molten metal injector projects into the holder furnace. The molten metal injector includes a cylinder defining a piston cavity housing a reciprocating piston for pumping the molten metal upward from the holder furnace to the mold cavity. The cylinder and piston are at least partially submerged in the molten metal when the holder furnace contains the molten metal. The cylinder or the piston includes a molten metal intake for receiving the molten metal into the piston cavity when the holder furnace contains molten metal. A conduit connects the piston cavity to the mold cavity. A molten metal filter is located in the conduit for filtering the molten metal passing through the conduit during the reciprocating movement of the piston. The molten metal intake may be a valve connected to the cylinder, a gap formed between the piston and an open end of the cylinder, an aperture defined in the sidewall of the cylinder, or a ball check valve incorporated into the piston. A second molten metal filter preferably covers the molten metal intake to the injector.

49 CFR 192.177 - Additional provisions for bottle-type holders.

Code of Federal Regulations, 2012 CFR

2012-10-01

... performed on the holder after it has been heat treated or stress relieved, except that copper wires may be... produces a hoop stress at least equal to 85 percent of the SMYS. (5) The holder, connection pipe, and...

49 CFR 192.177 - Additional provisions for bottle-type holders.

Code of Federal Regulations, 2014 CFR

2014-10-01

... performed on the holder after it has been heat treated or stress relieved, except that copper wires may be... produces a hoop stress at least equal to 85 percent of the SMYS. (5) The holder, connection pipe, and...

49 CFR 192.177 - Additional provisions for bottle-type holders.

Code of Federal Regulations, 2013 CFR

2013-10-01

... performed on the holder after it has been heat treated or stress relieved, except that copper wires may be... produces a hoop stress at least equal to 85 percent of the SMYS. (5) The holder, connection pipe, and...

Development of x-ray laminography under an x-ray microscopic condition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hoshino, Masato; Uesugi, Kentaro; Takeuchi, Akihisa

2011-07-15

An x-ray laminography system under an x-ray microscopic condition was developed to obtain a three-dimensional structure of laterally-extended planar objects which were difficult to observe by x-ray tomography. An x-ray laminography technique was introduced to an x-ray transmission microscope with zone plate optics. Three prototype sample holders were evaluated for x-ray imaging laminography. Layered copper grid sheets were imaged as a laminated sample. Diatomite powder on a silicon nitride membrane was measured to confirm the applicability of this method to non-planar micro-specimens placed on the membrane. The three-dimensional information of diatom shells on the membrane was obtained at a spatialmore » resolution of sub-micron. Images of biological cells on the membrane were also obtained by using a Zernike phase contrast technique.« less

Novel geometry for simultaneous resistive, Hall and optical measurement of MgHx thin films

NASA Astrophysics Data System (ADS)

Koon, D. W.; Griffin, C. C. W.; Ares, J. R.; Leardini, F.; Sanchez, C.

2009-03-01

We describe a novel specimen geometry we have used to simultaneously probe optical transmission, sheet resistance and sheet Hall resistance in 100nm Mg films during hydrogen absorption. A Mg-film cloverleaf overlaps four rectangular Pd pads at the corners of a glass slide, a variation on a two-pad geometry used by Ingason and Olafsson for resistive studies of Pd-capped MgHx films [J. Alloys and Compounds 404- 406 (2005), 469-72.]. Hydrogen diffuses laterally through the Pd pads before entering the magnesium layer from below. The sample holder also includes an LED-photodiode pair for measuring [monochromatic] optical transmission. We show that the simultaneous measurement of these three quantities during the metal-to-insulator transition in a hydriding MgHx film allows for a more complete understanding of the hydriding process in these films.

Fuel cell cooler assembly and edge seal means therefor

DOEpatents

Breault, Richard D.; Roethlein, Richard J.; Congdon, Joseph V.

1980-01-01

A cooler assembly for a stack of fuel cells comprises a fibrous, porous coolant tube holder sandwiched between and bonded to at least one of a pair of gas impervious graphite plates. The tubes are disposed in channels which pass through the holder. The channels are as deep as the holder thickness, which is substantially the same as the outer diameter of the tubes. Gas seals along the edges of the holder parallel to the direction of the channels are gas impervious graphite strips.

77 FR 23490 - Agency Information Collection Activities: Country of Origin Marking Requirements for Containers...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-19

... Activities: Country of Origin Marking Requirements for Containers or Holders AGENCY: U.S. Customs and Border... of Origin Marking Requirements for Containers or Holders. This is a proposed extension of an... Requirements for Containers or Holders. [[Page 23491

Effects of Document Holder on Postural Neck Muscles Activity among Computer Users: A Preliminary Study.

PubMed

Ambusam, Subramaniam; Omar, Baharudin; Joseph, Leonard; Deepashini, Harithasan

2015-01-01

Computer users are exposed to work related neck disorders due to repetitive movement and static posture for prolonged period. Viewing document and typing simultaneously are one of the contributing factors for neck disorders. This preliminary study was conducted to evaluate the effects of the document holder on the postural neck muscles activity among computer users. Nine healthy participants with pre-defined inclusion and exclusion criteria were recruited for the study. Neck muscles activity were analyzed using the surface electromyography (EMG) in five different document location such as flat right, flat left, flat center, stand right and stand left during a 5 min typing task. The mean and standard deviation results showed a least amount of muscles activity using a document holder compared to without document holder. Nevertheless, the statistical analysis showed no significant differences between the using of a document holder. The effects of document holder on head excursion and neck muscle activity is recommended in clinical neck pain population.

Surface mount component jig

DOEpatents

Kronberg, James W.

1990-08-07

A device for bending and trimming the pins of a dual-inline-package component and the like for surface mounting rather than through mounting to a circuit board comprises, in a first part, in pin cutter astride a holder having a recess for holding the component, a first spring therebetween, and, in a second part, two flat members pivotally interconnected by a hinge and urged to an upward peaked position from a downward peaked position by a second spring. As a downward force is applied to the pin cutter it urges the holder downward, assisted by the first spring and a pair of ridges riding on shoulders of the holder, to carry the component against the upward peaked flat members which guide the pins outwardly. As the holder continues downwardly, the flat members pivot to the downward peaked position bending the pins upwardly against the sides of the holder. When the downward movement is met with sufficient resistance, the ridges of the pin cutter ride over the holder's shoulders to continue downward to cut any excess length of pin.

Evaluation of Different Holder Devices for Freeze-Drying in Dual-Chamber Cartridges With a Focus on Energy Transfer.

PubMed

Korpus, Christoph; Friess, Wolfgang

2017-04-01

For freeze-drying in dual-chamber cartridges, a holder device to enable handling and safe positioning in the freeze-dryer is necessary. The aim of this study was to analyze 4 different types of holder devices and to define the best system based on energy transfer. The main criteria were drying homogeneity, ability to minimize the influence of atypical radiation on product temperatures, and heat transfer effectiveness. The shell holder reduced the influence of atypical radiation by almost 60% compared to a block system and yielded the most homogenous sublimation rates. Besides the most efficient heat transfer with values of 1.58E-4 ± 2.06E-6 cal/(s*cm 2 *K) at 60 mTorr to 3.63E-4 ± 1.85E-5 cal/(s*cm 2 *K) at 200 mTorr for K tot , reaction times to shelf temperature changes were up to 4 times shorter compared to the other holder systems and even faster than for vials. The flexible holder provided a comparable shielding against atypical radiation as the shell but introduced a third barrier against energy transfer. Block and guardrail holder were the least efficient system tested. Hence, the shell holder provided the best radiation shielding, enhanced the transferability of the results to a larger scale, and improved the homogeneity between the dual-chamber cartridges. Copyright © 2017 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

75 FR 59711 - Audit Program for Texas Flexible Permit Holders

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-28

... ENVIRONMENTAL PROTECTION AGENCY [EPA-R06-OAR-2010-0510; FRL-9207-4] Audit Program for Texas... Act (CAA) voluntary audit compliance program for flexible permit holders in the State of Texas (hereinafter ``Audit Program''); response to public comments. SUMMARY: EPA is offering holders of Texas...

12 CFR 611.1215 - Communications with the public and equity holders.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 12 Banks and Banking 6 2010-01-01 2010-01-01 false Communications with the public and equity holders. 611.1215 Section 611.1215 Banks and Banking FARM CREDIT ADMINISTRATION FARM CREDIT SYSTEM... holders. (a) Communications after commencement resolution and before termination. The terminating...

21 CFR 892.1920 - Radiographic head holder.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Radiographic head holder. 892.1920 Section 892.1920 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.1920 Radiographic head holder. (a...

High-resolution Episcopic Microscopy (HREM) - Simple and Robust Protocols for Processing and Visualizing Organic Materials

PubMed Central

Geyer, Stefan H.; Maurer-Gesek, Barbara; Reissig, Lukas F.; Weninger, Wolfgang J.

2017-01-01

We provide simple protocols for generating digital volume data with the high-resolution episcopic microscopy (HREM) method. HREM is capable of imaging organic materials with volumes up to 5 x 5 x 7 mm3 in typical numeric resolutions between 1 x 1 x 1 and 5 x 5 x 5 µm3. Specimens are embedded in methacrylate resin and sectioned on a microtome. After each section an image of the block surface is captured with a digital video camera that sits on the phototube connected to the compound microscope head. The optical axis passes through a green fluorescent protein (GFP) filter cube and is aligned with a position, at which the bock holder arm comes to rest after each section. In this way, a series of inherently aligned digital images, displaying subsequent block surfaces are produced. Loading such an image series in three-dimensional (3D) visualization software facilitates the immediate conversion to digital volume data, which permit virtual sectioning in various orthogonal and oblique planes and the creation of volume and surface rendered computer models. We present three simple, tissue specific protocols for processing various groups of organic specimens, including mouse, chick, quail, frog and zebra fish embryos, human biopsy material, uncoated paper and skin replacement material. PMID:28715372

High-resolution Episcopic Microscopy (HREM) - Simple and Robust Protocols for Processing and Visualizing Organic Materials.

PubMed

Geyer, Stefan H; Maurer-Gesek, Barbara; Reissig, Lukas F; Weninger, Wolfgang J

2017-07-07

We provide simple protocols for generating digital volume data with the high-resolution episcopic microscopy (HREM) method. HREM is capable of imaging organic materials with volumes up to 5 x 5 x 7 mm 3 in typical numeric resolutions between 1 x 1 x 1 and 5 x 5 x 5 µm 3 . Specimens are embedded in methacrylate resin and sectioned on a microtome. After each section an image of the block surface is captured with a digital video camera that sits on the phototube connected to the compound microscope head. The optical axis passes through a green fluorescent protein (GFP) filter cube and is aligned with a position, at which the bock holder arm comes to rest after each section. In this way, a series of inherently aligned digital images, displaying subsequent block surfaces are produced. Loading such an image series in three-dimensional (3D) visualization software facilitates the immediate conversion to digital volume data, which permit virtual sectioning in various orthogonal and oblique planes and the creation of volume and surface rendered computer models. We present three simple, tissue specific protocols for processing various groups of organic specimens, including mouse, chick, quail, frog and zebra fish embryos, human biopsy material, uncoated paper and skin replacement material.

21 CFR 1311.20 - Coordinators for CSOS digital certificate holders.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 9 2010-04-01 2010-04-01 false Coordinators for CSOS digital certificate holders... REQUIREMENTS FOR ELECTRONIC ORDERS AND PRESCRIPTIONS (Eff. 6-1-10) Obtaining and Using Digital Certificates for Electronic Orders § 1311.20 Coordinators for CSOS digital certificate holders. (a) Each registrant...

7 CFR 1463.105 - Base quota levels for eligible quota holders.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 10 2011-01-01 2011-01-01 false Base quota levels for eligible quota holders. 1463.105 Section 1463.105 Agriculture Regulations of the Department of Agriculture (Continued) COMMODITY... TRANSITION PROGRAM Tobacco Transition Payment Program § 1463.105 Base quota levels for eligible quota holders...

7 CFR 1463.105 - Base quota levels for eligible quota holders.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 10 2012-01-01 2012-01-01 false Base quota levels for eligible quota holders. 1463.105 Section 1463.105 Agriculture Regulations of the Department of Agriculture (Continued) COMMODITY... TRANSITION PROGRAM Tobacco Transition Payment Program § 1463.105 Base quota levels for eligible quota holders...

[Measurement of external pressure of peroneal nerve tract coming in contact with lithotomy leg holders using pressure distribution measurement system BIG-MAT®].

PubMed

Mizuno, Ju; Namba, Chikara; Takahashi, Toru

2014-10-01

We investigated external pressure on peroneal nerve tract coming in contact with two kinds of leg holders using pressure distribution measurement system BIG- MAT® (Nitta Corp., Osaka) in the lithotomy position Peak contact (active) pressure at the left fibular head region coming in contact with knee-crutch-type leg holder M® (Takara Belmont Corp., Osaka), which supports the left popliteal fossa, was 78.0 ± 26.4 mmHg. On the other hand, peak contact pressure at the left lateral lower leg region coming in contact with boot-support-type leg holder Bel Flex® (Takara Belmont Corp., Osaka), which supports the left lower leg and foot was 26.3±7.9 mmHg. These results suggest that use of knee-crutch-type leg holder is more likely to induce common peroneal nerve palsy at the fibular head region, but use of boot-support-type leg holder dose not easily induce superficial peroneal nerve palsy at the lateral lower leg region, because capillary blood pressure is known to be 32 mmHg. Safer holders for positioning will be developed to prevent nerve palsy based on the analysis of chronological change in external pressure using BIG-MAT® system during anesthesia.

Heat susceptibility of interleukin-10 and other cytokines in donor human milk.

PubMed

Untalan, Peter B; Keeney, Susan E; Palkowetz, Kimberly H; Rivera, Audelio; Goldman, Armond S

2009-09-01

Holder pasteurization renders donor human milk safe for consumption. Because human milk reduces the risk of necrotizing enterocolitis in preterm infants, we tested whether Holder pasteurization affects certain factors in human milk that protect the intestines: epidermal growth factor (EGF), transforming growth factor (TGF)-beta1, erythropoietin (EPO), and interleukin (IL)-10. Donor human milk from a milk bank was examined. The aqueous phase of 17 samples of donor term human milk (mean duration of lactation, 8 +/- 3.5 months) was examined before and after Holder pasteurization. In the case of IL-10, lesser degrees of pasteurization were also evaluated. The agents were quantified using enzyme immunoassays. The function of IL-10 was also tested. Concentrations of EGF and IL-10 were markedly lower than previously reported values in human milk from earlier phases of lactation. Holder pasteurization significantly reduced the concentrations of EPO and IL-10, whereas lesser degrees of heating increased the detection of IL-10. The immunosuppression of T-cell proliferation by human milk, thought to be attributed to IL-10 alone, persisted after Holder pasteurization. Holder pasteurization greatly decreased concentrations of EPO and IL-10 in human milk. These decreases may impact the ability of human milk to protect against necrotizing enterocolitis. Evidence of possible binding of IL-10 to other proteins in human milk was also found. Experiments to test whether Holder pasteurization affects the function of IL-10 in human milk produced evidence for an agent in human milk other than IL-10 that inhibits T-cell proliferation and resists Holder pasteurization.

32 CFR 767.9 - Content of permit holder's final report.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 32 National Defense 5 2014-07-01 2014-07-01 false Content of permit holder's final report. 767.9 Section 767.9 National Defense Department of Defense (Continued) DEPARTMENT OF THE NAVY MISCELLANEOUS... JURISDICATION OF THE DEPARTMENT OF THE NAVY Permit Guidelines § 767.9 Content of permit holder's final report...

32 CFR 767.9 - Content of permit holder's final report.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 32 National Defense 5 2013-07-01 2013-07-01 false Content of permit holder's final report. 767.9 Section 767.9 National Defense Department of Defense (Continued) DEPARTMENT OF THE NAVY MISCELLANEOUS... JURISDICATION OF THE DEPARTMENT OF THE NAVY Permit Guidelines § 767.9 Content of permit holder's final report...

Quick-Change Ceramic Flame Holder for High-Output Torches

NASA Technical Reports Server (NTRS)

Haskin, Henry

2010-01-01

Researchers at NASA's Langley Research Center have developed a new ceramic design flame holder with a service temperature of 4,000 F (2,204 C). The combination of high strength and high temperature capability, as well as a twist-lock mounting method to the steel burner, sets this flame holder apart from existing technology.

77 FR 37724 - Self-Regulatory Organizations; Chicago Board Options Exchange, Incorporated; Notice of Filing of...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-22

... (``Qualifying Trading Permit Holders''), the Exchange may determine on a class-by-class basis to permit SAL responses by all CBOE Market-Makers and Qualifying Trading Permit Holders. The proposed rule change allows... auction messages and eliminates the concept of Qualifying Trading Permit Holders under this provision...

77 FR 67421 - Self-Regulatory Organizations; Chicago Board Options Exchange, Incorporated; Notice of Filing and...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-09

... makes available to Trading Permit Holders various application programming interfaces (``APIs''),\\4\\ such... Permit Holders to enter and execute orders, as well as submit certain order and trade data to the Exchange, which data the Exchange uses to conduct surveillances of its markets and Trading Permit Holders...

75 FR 17457 - Self-Regulatory Organizations; NYSE Amex LLC; Order Granting Accelerated Approval of the Proposed...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-06

... protection. The proposal requires ATP holders to indicate whether Customer orders are ``Professional Customer'' orders.\\5\\ To comply with this requirement, ATP holders would be required to review their customers... represented as Professional Customer orders for the next calendar quarter. ATP Holders would be required to...

Financial Statistics of Noncommercial Television License Holders: Fiscal Year 1970. Revised Edition.

ERIC Educational Resources Information Center

Pedone, Ronald J.; And Others

Fiscal year 1970 financial data for 129 educational television license holders responsible for 195 stations in the aggregate United States are presented. The data are grouped by type of license holder (institution of higher education, local public school system, state authority, or community organization) and region (North Atlantic, Great Lakes…

38 CFR 36.4341 - Death or insolvency of holder.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 2 2010-07-01 2010-07-01 false Death or insolvency of... Death or insolvency of holder. (a) Immediately upon the death of the holder and without the necessity of... expiration of charter, by forfeiture, or otherwise shall be treated as is the death of an individual as...

38 CFR 36.4277 - Release of security.

Code of Federal Regulations, 2010 CFR

2010-07-01

... payment of the indebtedness the holder shall not release a lien or other right in or to property held as..., the holder shall not release a lien under paragraph (a) of this section unless the consideration... released it shall be the holder's duty to acquire such lien on property of substantially equal value which...

17 CFR 240.14c-3 - Annual report to be furnished security holders.

Code of Federal Regulations, 2011 CFR

2011-04-01

... Notice of Internet Availability of Proxy Materials, annual report to security holders or information... 17 Commodity and Securities Exchanges 3 2011-04-01 2011-04-01 false Annual report to be furnished security holders. 240.14c-3 Section 240.14c-3 Commodity and Securities Exchanges SECURITIES AND EXCHANGE...

17 CFR 240.14c-3 - Annual report to be furnished security holders.

Code of Federal Regulations, 2012 CFR

2012-04-01

... Notice of Internet Availability of Proxy Materials, annual report to security holders or information... 17 Commodity and Securities Exchanges 3 2012-04-01 2012-04-01 false Annual report to be furnished security holders. 240.14c-3 Section 240.14c-3 Commodity and Securities Exchanges SECURITIES AND EXCHANGE...

17 CFR 240.14c-3 - Annual report to be furnished security holders.

Code of Federal Regulations, 2014 CFR

2014-04-01

... Notice of Internet Availability of Proxy Materials, annual report to security holders or information... 17 Commodity and Securities Exchanges 4 2014-04-01 2014-04-01 false Annual report to be furnished security holders. 240.14c-3 Section 240.14c-3 Commodity and Securities Exchanges SECURITIES AND EXCHANGE...

17 CFR 240.14c-3 - Annual report to be furnished security holders.

Code of Federal Regulations, 2013 CFR

2013-04-01

... Notice of Internet Availability of Proxy Materials, annual report to security holders or information... 17 Commodity and Securities Exchanges 3 2013-04-01 2013-04-01 false Annual report to be furnished security holders. 240.14c-3 Section 240.14c-3 Commodity and Securities Exchanges SECURITIES AND EXCHANGE...

78 FR 9720 - Agency Information Collection Activities: Holders or Containers Which Enter the United States...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-11

... Activities: Holders or Containers Which Enter the United States Duty Free AGENCY: U.S. Customs and Border... or Containers which enter the United States Duty Free. This is a proposed extension of an information..., or other technological techniques or other forms of information. Title: Holders or Containers which...

Filter holder and gasket assembly for candle or tube filters

DOEpatents

Lippert, Thomas Edwin; Alvin, Mary Anne; Bruck, Gerald Joseph; Smeltzer, Eugene E.

1999-03-02

A filter holder and gasket assembly for holding a candle filter element within a hot gas cleanup system pressure vessel. The filter holder and gasket assembly includes a filter housing, an annular spacer ring securely attached within the filter housing, a gasket sock, a top gasket, a middle gasket and a cast nut.

Filter holder assembly having extended collar spacer ring

DOEpatents

Alvin, Mary Anne; Bruck, Gerald J.

2002-01-01

A filter holder assembly is provided that utilizes a fail-safe regenerator unit with an annular spacer ring having an extended metal collar for containment and positioning of a compliant ceramic gasket used in the assembly. The filter holder assembly is disclosed for use with advanced composite, filament wound, and metal candle filters.

14 CFR 121.652 - Landing weather minimums: IFR: All certificate holders.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Landing weather minimums: IFR: All certificate holders. 121.652 Section 121.652 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT... Rules § 121.652 Landing weather minimums: IFR: All certificate holders. (a) If the pilot in command of...

14 CFR 121.652 - Landing weather minimums: IFR: All certificate holders.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Landing weather minimums: IFR: All certificate holders. 121.652 Section 121.652 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT... Rules § 121.652 Landing weather minimums: IFR: All certificate holders. (a) If the pilot in command of...

14 CFR 121.652 - Landing weather minimums: IFR: All certificate holders.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Landing weather minimums: IFR: All certificate holders. 121.652 Section 121.652 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT... Rules § 121.652 Landing weather minimums: IFR: All certificate holders. (a) If the pilot in command of...

14 CFR 121.652 - Landing weather minimums: IFR: All certificate holders.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Landing weather minimums: IFR: All certificate holders. 121.652 Section 121.652 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT... Rules § 121.652 Landing weather minimums: IFR: All certificate holders. (a) If the pilot in command of...

14 CFR 121.652 - Landing weather minimums: IFR: All certificate holders.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Landing weather minimums: IFR: All certificate holders. 121.652 Section 121.652 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT... Rules § 121.652 Landing weather minimums: IFR: All certificate holders. (a) If the pilot in command of...

19 CFR 10.41b - Clearance of serially numbered substantial holders or outer containers.

Code of Federal Regulations, 2014 CFR

2014-04-01

... or outer containers. 10.41b Section 10.41b Customs Duties U.S. CUSTOMS AND BORDER PROTECTION... holders or outer containers. (a) The holders and containers described in this section may be released... intermodal and similar containers or containers which are themselves vehicles or vehicle appurtenances and...

19 CFR 10.41b - Clearance of serially numbered substantial holders or outer containers.

Code of Federal Regulations, 2011 CFR

2011-04-01

... or outer containers. 10.41b Section 10.41b Customs Duties U.S. CUSTOMS AND BORDER PROTECTION... holders or outer containers. (a) The holders and containers described in this section may be released... intermodal and similar containers or containers which are themselves vehicles or vehicle appurtenances and...

19 CFR 10.41b - Clearance of serially numbered substantial holders or outer containers.

Code of Federal Regulations, 2010 CFR

2010-04-01

... or outer containers. 10.41b Section 10.41b Customs Duties U.S. CUSTOMS AND BORDER PROTECTION... holders or outer containers. (a) The holders and containers described in this section may be released... intermodal and similar containers or containers which are themselves vehicles or vehicle appurtenances and...

19 CFR 10.41b - Clearance of serially numbered substantial holders or outer containers.

Code of Federal Regulations, 2013 CFR

2013-04-01

... or outer containers. 10.41b Section 10.41b Customs Duties U.S. CUSTOMS AND BORDER PROTECTION... holders or outer containers. (a) The holders and containers described in this section may be released... intermodal and similar containers or containers which are themselves vehicles or vehicle appurtenances and...

19 CFR 10.41b - Clearance of serially numbered substantial holders or outer containers.

Code of Federal Regulations, 2012 CFR

2012-04-01

... or outer containers. 10.41b Section 10.41b Customs Duties U.S. CUSTOMS AND BORDER PROTECTION... holders or outer containers. (a) The holders and containers described in this section may be released... intermodal and similar containers or containers which are themselves vehicles or vehicle appurtenances and...

12 CFR 569.3 - Holders of proxies.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 12 Banks and Banking 5 2010-01-01 2010-01-01 false Holders of proxies. 569.3 Section 569.3 Banks and Banking OFFICE OF THRIFT SUPERVISION, DEPARTMENT OF THE TREASURY PROXIES § 569.3 Holders of proxies. No proxy of a mutual savings association with a term greater than eleven months or solicited at...

76 FR 65180 - Proposed Information Collection; Comment Request; Application to Shuck Surf Clams/Ocean Quahogs...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-20

.... Method of Collection Requests from allocation holders to transfer quota use paper applications or an... submitted on or before December 19, 2011. ADDRESSES: Direct all written comments to Diana Hynek... transferable quota (ITQ) allocation holders in order to process and track requests from the allocation holders...

38 CFR 36.4341 - Death or insolvency of holder.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 2 2011-07-01 2011-07-01 false Death or insolvency of... Death or insolvency of holder. (a) Immediately upon the death of the holder and without the necessity of... expiration of charter, by forfeiture, or otherwise shall be treated as is the death of an individual as...

38 CFR 36.4341 - Death or insolvency of holder.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 2 2014-07-01 2014-07-01 false Death or insolvency of... Death or insolvency of holder. (a) Immediately upon the death of the holder and without the necessity of... expiration of charter, by forfeiture, or otherwise shall be treated as is the death of an individual as...

38 CFR 36.4341 - Death or insolvency of holder.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 2 2012-07-01 2012-07-01 false Death or insolvency of... Death or insolvency of holder. (a) Immediately upon the death of the holder and without the necessity of... expiration of charter, by forfeiture, or otherwise shall be treated as is the death of an individual as...

38 CFR 36.4341 - Death or insolvency of holder.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 2 2013-07-01 2013-07-01 false Death or insolvency of... Death or insolvency of holder. (a) Immediately upon the death of the holder and without the necessity of... expiration of charter, by forfeiture, or otherwise shall be treated as is the death of an individual as...

7 CFR 3565.405 - Repurchase of guaranteed loans.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 business days from the date of the written demand letter to the lender from the Holder requesting... written demand letter by the Holder. The lender may agree to repurchase the unpaid portion of the entire... of the Holder's written demand letter to do so. The guarantee does not cover any unguaranteed portion...

7 CFR 1779.78 - Repurchase of loan.

Code of Federal Regulations, 2011 CFR

2011-01-01

... written demand from the holder when the borrower is in default not less than 60 days on payment. The... less the lender's servicing fee. The guarantee does not cover the note interest to the holder on the guaranteed loan accruing after 90 days from the date of the demand letter to the lender. The holder will...

7 CFR 1779.78 - Repurchase of loan.

Code of Federal Regulations, 2010 CFR

2010-01-01

... written demand from the holder when the borrower is in default not less than 60 days on payment. The... less the lender's servicing fee. The guarantee does not cover the note interest to the holder on the guaranteed loan accruing after 90 days from the date of the demand letter to the lender. The holder will...

Diabetes management in Commercial Driver License holders.

PubMed

Kerr, Jessica L; Frichtl, Kelsey D; Behnen, Erin M

2015-04-01

The purpose of this study is to evaluate diabetes management in Commercial Driver License (CDL) holders, how prescribing habits change when treating this patient population, and health care providers' knowledge of regulations concerning insulin use in CDL holders. A survey was posted on the American Association of Diabetes Educators (AADE) Communities of Interest websites and was open for 2 weeks. The anonymous survey collected demographic data and evaluated the perspectives of health care providers on diabetes management in CDL holders. Descriptive statistics were used to analyze the survey results. A total of 139 AADE members responded to the survey, and 22.2% were prescribing providers. Findings from the survey indicated an overall lack of knowledge by health care professionals regarding the current laws affecting diabetes management in CDL holders. Most participants emphasized the need for making decisions on CDL suspension on a case-by-case basis, and some expressed concern that current laws may not be appropriate. Additional diabetes education for health care providers who treat CDL holders is warranted as many health care providers were not familiar with current regulations and management strategies. © 2015 The Author(s).

Grinding arrangement for ball nose milling cutters

NASA Technical Reports Server (NTRS)

Burch, C. F. (Inventor)

1974-01-01

A grinding arrangement for spiral fluted ball nose end mills and like tools includes a tool holder for positioning the tool relative to a grinding wheel. The tool is mounted in a spindle within the tool holder for rotation about its centerline and the tool holder is pivotably mounted for angular movement about an axis which intersects that centerline. A follower arm of a cam follower secured to the spindle cooperates with a specially shaped cam to provide rotation of the tool during the angular movement of the tool holder during the grinding cycle, by an amount determined by the cam profile. In this way the surface of the cutting edge in contact with the grinding wheel is maintained at the same height on the grinding wheel throughout the angular movement of the tool holder during the grinding cycle.

Gritty Surface Sample Holder Invented To Obtain Correct X-ray Absorption Fine Structure Spectra for Concentrated Materials by Fluorescence Yield.

PubMed

Abe, Hitoshi; Niwa, Yasuhiro; Kimura, Masao; Murakami, Youichi; Yokoyama, Toshiharu; Hosono, Hideo

2016-04-05

A gritty surface sample holder has been invented to obtain correct XAFS spectra for concentrated samples by fluorescence yield (FY). Materials are usually mixed with boron nitride (BN) to prepare proper concentrations to measure XAFS spectra. Some materials, however, could not be mixed with BN and would be measured in too concentrated conditions to obtain correct XAFS spectra. Consequently, XAFS spectra will be incorrect typically with decreased intensities of the peaks. We have invented the gritty surface sample holders to obtain correct XAFS spectra even for concentrated materials for FY measurements. Pure Cu and CuO powders were measured mounted on the sample holders, and the same spectra were obtained as transmission spectra of properly prepared samples. This sample holder is useful to measure XAFS for any concentrated materials.

Implant image quality in dental radiographs recorded using a customized imaging guide or a standard film holder.

PubMed

Schropp, Lars; Stavropoulos, Andreas; Spin-Neto, Rubens; Wenzel, Ann

2012-01-01

To compare a customized imaging guide and a standard film holder for obtaining optimally projected intraoral radiographs of dental implants. Intraoral radiographs of four screw-type implants with different inclination placed in an upper or lower dental phantom model were recorded by 32 groups of examiners after a short instruction in the use of the RB-RB/LB-LB mnemonic rule. Half of the examiners recorded the images using a standard film holder and the other half used a customized imaging guide. Each radiograph was assessed under blinded conditions with regard to rendering of the implant threads and was assigned to one of four quality categories: (1) perfect, (2) not perfect, but clinically acceptable, (3) not acceptable, and (4) hopeless. For the upper jaw, the same number of exposures per implant were made to achieve an acceptable image (P=0.86) by the standard film holder method (median=2) and the imaging guide method (median=2). For the lower jaw, medians for the imaging guide method and the film holder method were 1 and 2, respectively (P=0.004). For the imaging guide method, the first exposure was rated as perfect/acceptable in 62% of the cases and for the film holder method in 41% of the cases (P=0.013). After ≤ 2 exposures, 78% (imaging guide method) and 69% (film holder method) of the implant images were perfect/acceptable (P=0.23). The implant inclination did not have a major influence on the outcomes. Perfect or acceptable images were achieved after two exposures with the same frequency either using a customized imaging guide method or a standard film holder method. However, the use of a customized imaging guide method was overall significantly superior to a standard film holder method in terms of obtaining perfect or acceptable images with only one exposure. © 2011 John Wiley & Sons A/S.

A new irradiation method with a neutron filter for silicon neutron transmutation doping at the Japan research reactor no. 3 (JRR-3).

PubMed

Komeda, Masao; Kawasaki, Kozo; Obara, Toru

2013-04-01

We studied a new silicon irradiation holder with a neutron filter designed to make the vertical neutron flux profile uniform. Since an irradiation holder has to be made of a low activation material, we applied aluminum blended with B4C as the holder material. Irradiation methods to achieve uniform flux with a filter are discussed using Monte-Carlo calculation code MVP. Validation of the use of the MVP code for the holder's analyses is also discussed via characteristic experiments. Copyright © 2013 Elsevier Ltd. All rights reserved.

System for testing bearings

NASA Technical Reports Server (NTRS)

Gibson, John C. (Inventor)

1993-01-01

Disclosed here is a system for testing bearings wherein a pair of spaced bearings provides support for a shaft on which is mounted a bearing to be tested, this bearing being mounted in a bearing holder spaced from and in alignment with the pair of bearings. The bearing holder is provided with an annular collar positioned in an opening in the bearing holder for holding the bearing to be tested. A screw threaded through the bearing holder into engagement with the annular collar can be turned to force the collar radially out of alignment with the pair of bearings to apply a radial load to the bearing.

Chemical analysis kit for the presence of explosives

DOEpatents

Eckels, Joel Del [Livermore, CA; Nunes,; Peter, J [Danville, CA; Alcaraz, Armando [Livermore, CA; Whipple, Richard E [Livermore, CA

2011-05-10

A tester for testing for explosives associated with a test location comprising a first explosives detecting reagent; a first reagent holder, the first reagent holder containing the first explosives detecting reagent; a second explosives detecting reagent; a second reagent holder, the second reagent holder containing the second explosives detecting reagent; a sample collection unit for exposure to the test location, exposure to the first explosives detecting reagent, and exposure to the second explosives detecting reagent; and a body unit containing a heater for heating the sample collection unit for testing the test location for the explosives.

Synthesis and characterization of Cu nanotubes and nanothreads by electrical arc evaporation.

PubMed

Yadav, Ram Manohar; Singh, A K; Srivastava, O N

2003-06-01

We report the formation and characterization of copper nanostructures, nanotubules and nanothreads, which were obtained by electrical arc evaporation of Cu electrodes under varied conditions of He ambience. Electrical arc evaporation was done with approximately 10 V and (approximately 50-100 A) DC current. The current was used in a pulse mode. The evaporated material was condensed on a formvar-coated Cu grid mounted on a liquid N2-cooled specimen holder. Transmission electron microscopy was employed to characterize the condensed materials. These investigations revealed that the condensed materials consisted of the mentioned nanostructures. Nanotubes and nanothreads are formed for a He pressure in the chamber corresponding to approximately 140 and approximately 500 torr, respectively. Extensive electron microscopic investigations showed that the diameter of the nanotubes varied from approximately 5 nm to approximately 50 nm and their length from 2 microns to 3 microns.

IC(B,T,STRAIN) Characterisation of a Nb3Sn Internal Tin Strand with Enhanced Specification for Use in Fusion Conductors

NASA Astrophysics Data System (ADS)

Pasztor, G.; Bruzzone, P.

2004-06-01

The dc performance of a recently produced internal tin route Nb3Sn strand with enhanced specification is studied extensively and compared with predecessor wires manufactured by the suppliers for the ITER Model Coils in 1996. The wire has been selected for use in a full size, developmental cable-in-conduit conductor sample, which is being tested in the SULTAN Test Facility. The critical current, Ic, and the index of the current/voltage characteristic, n, are measured over a broad range of field and temperature, using ITER standard sample holders, made of TiAlV grooved cylinders. The behavior of Ic versus applied tensile strain is also investigated at 4.2 K and 12 T, on straight specimens. Scaling law parameters are drawn from the fit of the experimental results. The implications of the test results to the design of the fusion conductors are discussed.

Method and device for intraoperative imaging of lumpectomy specimens to provide feedback to breast surgeon for prompt re-excision during the same procedure

NASA Astrophysics Data System (ADS)

Krol, Andrzej; Hemingway, Susan; Kort, Kara; de la Rosa, Gustavo; Adhikary, Ravi; Masrani, Deepa; Feiglin, David; O'Connell, Avice; Nagarajan, Mahesh; Yang, Chien-Chun; Wismüller, Axel

2014-03-01

Breast conserving therapy (BCT) of breast cancer is now widely accepted due to improved cosmetic outcome and improved patients' quality of life. One of the critical issues in performing breast-conserving surgery is trying to achieve microscopically clear surgical margins while maintaining excellent cosmesis. Unfortunately, unacceptably close or positive surgical margins occur in at least 20-25% of all patients undergoing BCT requiring repeat surgical excision days or weeks later, as permanent histopathology routinely takes days to complete. Our aim is to develop a better method for intraoperative imaging of non-palpable breast malignancies excised by wire or needle localization. Providing non-deformed three dimensional imaging of the excised breast tissue should allow more accurate assessment of tumor margins and consequently allow further excision at the time of initial surgery thus limiting the enormous financial and emotional burden of additional surgery. We have designed and constructed a device that allows preservation of the excised breast tissue in its natural anatomic position relative to the breast as it is imaged to assess adequate excision. We performed initial tests with needle-guided lumpectomy specimens using micro-CT and digital breast tomosynthesis (DBT). Our device consists of a plastic sphere inside a cylindrical holder. The surgeon inserts a freshly excised piece of breast tissue into the sphere and matches its anatomic orientation with the fiducial markers on the sphere. A custom-shaped foam is placed inside the sphere to prevent specimen deformation due to gravity. DBT followed by micro-CT images of the specimen were obtained. We confirmed that our device preserved spatial orientation of the excised breast tissue and that the location error was lower than 10mm and 10 degrees. The initial obtained results indicate that breast lesions containing microcalcifications allow a good 3D imaging of margins providing immediate intraoperative feedback for further excision as needed at the initial operation.

Organization and operation of the marine ornamental fish and invertebrate export fishery in Puerto Rico.

PubMed

Legorel, Richard S; Hardin, Mark P; Ter-Ghazaryan, Diana

2005-05-01

This fishery was examined utilizing public records, stakeholder interviews, and operational site visits to describe the fishery for the Puerto Rico Coral Reef Advisory Committee as a first step toward development of policies for the effective management of these natural resources. The fishery is not large, including fewer than 20 licensed fishers operating primarily on the west end of the island. Only three operators export product, with the remaining fishers providing specimens to the exporters based upon customer orders. Most collection of coral reef species occurs over hard rubble zones mixed with relic reef structures and rock, or on the sides and frontal areas of active reefs. Other species are collected from among mangrove prop root zones, tidal flats, and seagrass beds. Collections are made using simple barrier and dip nets for fish and motile invertebrates such as shrimp. Invertebrates such as crabs, starfish, and sea cucumbers are commonly collected by overturning small rocks, gathering the specimens, and then replacing the rocks in their original positions. Specimens are carried to the boat and transferred to individual cup holders to maximize survival. Although statements concerning former use of chemicals to assist capture were noted, no evidence of current chemical use was observed. Specimens are held in re-circulating seawater systems onshore until collections are aggregated and shipped. The fishery strives to operate with mortality of<1%, as mortalities of>3% are described as unacceptable to customers. More than 100 fish species are collected in this fishery, but the top ten species account for >70% of the total numbers and >60% of the total value of the fishery, with a single species, Gramma loreto (Royal Gramma), comprising >40% of the numbers. More than 100 species of invertebrates are collected, but this fishery is also dominated by a handful of species, including anemones, hermit crabs, turbo snails, serpent starfish, and feather duster polychaetes.

14 CFR 43.3 - Persons authorized to perform maintenance, preventive maintenance, rebuilding, and alterations.

Code of Federal Regulations, 2010 CFR

2010-01-01

... certificate holder has written procedures available to the pilot to evaluate the accomplishment of the task... alterations as provided in part 121 or 135. (g) Except for holders of a sport pilot certificate, the holder of a pilot certificate issued under part 61 may perform preventive maintenance on any aircraft owned or...

14 CFR 43.3 - Persons authorized to perform maintenance, preventive maintenance, rebuilding, and alterations.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 135. (g) Except for holders of a sport pilot certificate, the holder of a pilot certificate issued... is not used under part 121, 129, or 135 of this chapter. The holder of a sport pilot certificate may... airworthiness certificate in the light-sport category. (h) Notwithstanding the provisions of paragraph (g) of...

17 CFR 270.32a-2 - Exemption for initial period from vote of security holders on independent public accountant for...

Code of Federal Regulations, 2010 CFR

2010-04-01

... from vote of security holders on independent public accountant for certain registered separate accounts... from vote of security holders on independent public accountant for certain registered separate accounts... 32(a) of the Act that selection of an independent public accountant shall have been submitted for...

75 FR 40010 - Self-Regulatory Organizations; NYSE Amex LLC; Notice of Filing and Immediate Effectiveness of...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-13

... Proposed Rule Change 1. Purpose Currently, the Exchange aggregates all of an ATP Holder's volume at the trading permit level for purposes of the Firm Proprietary Manual tiers. Recently, certain ATP Holders have... this filing, the Exchange proposes to allow its ATP Holders to elect to have their Firm Proprietary...

78 FR 60362 - Self-Regulatory Organizations; NYSE MKT LLC; Notice of Filing and Immediate Effectiveness of...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-01

... the Exchange on each ATP Holder for all options transactions, including mini-options, executed or cleared by the ATP Holder that are cleared by The Options Clearing Corporation (``OCC'') in the customer range (i.e., transactions that clear in the customer account of the ATP Holder's clearing firm at OCC...

78 FR 48456 - Notice of Cancellation of Customs Broker Licenses Due to Death of the License Holder

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-08

... Customs Broker Licenses Due to Death of the License Holder AGENCY: U.S. Customs and Border Protection, Department of Homeland Security. ACTION: Customs broker license cancellation due to death of the broker... without prejudice due to the death of the license holders. SUPPLEMENTARY INFORMATION: Notice is hereby...

76 FR 48009 - Federal Motor Vehicle Safety Standards; Lamps, Reflective Devices, and Associated Equipment

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-08

... of the license plate holder. Ford requested that the paragraph be deleted, claiming that the rear license plate holder is not a lamp, reflective device, or piece of associated equipment and is not... the existing incorporation by reference only applied to the lamps, and not to the license plate holder...

Filter holder and gasket assembly for candle or tube filters

DOEpatents

Lippert, T.E.; Alvin, M.A.; Bruck, G.J.; Smeltzer, E.E.

1999-03-02

A filter holder and gasket assembly are disclosed for holding a candle filter element within a hot gas cleanup system pressure vessel. The filter holder and gasket assembly includes a filter housing, an annular spacer ring securely attached within the filter housing, a gasket sock, a top gasket, a middle gasket and a cast nut. 9 figs.

42 CFR 60.42 - Records, reports, inspection, and audit requirements for HEAL lenders and holders.

Code of Federal Regulations, 2010 CFR

2010-10-01

... OF HEALTH AND HUMAN SERVICES GRANTS HEALTH EDUCATION ASSISTANCE LOAN PROGRAM The Lender and Holder... must maintain for each borrower a payment history showing the date and amount of each payment received... lender or holder must also maintain for each loan a collection history showing the date and subject of...

77 FR 16091 - Order Modifying Licenses With Regard to Requirements for Mitigation Strategies for Beyond-Design...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-19

.... (as shown in Attachment 1)) EA-12-049 I The Licensees and construction permits (CP) holders \\1..., ``Licenses, Certifications, and Approvals for Nuclear Power Plants.'' \\1\\ CP holders, as used in this Order... that additional requirements must be imposed on Licensees or CP holders to increase the [[Page 16092...

7 CFR 762.144 - Repurchase of guaranteed portion from a secondary market holder.

Code of Federal Regulations, 2010 CFR

2010-01-01

... discrepancy is resolved. (iii) In the case of a request for Agency purchase, the Agency will only pay interest... and the amount due the holder. (ii) Any discrepancy between the amount claimed by the holder and the... approved by the Agency. The Agency will not participate in resolution of any such discrepancy. When there...

26 CFR 1.860C-1 - Taxation of holders of residual interests.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 26 Internal Revenue 9 2010-04-01 2010-04-01 false Taxation of holders of residual interests. 1.860C-1 Section 1.860C-1 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES Real Estate Investment Trusts § 1.860C-1 Taxation of holders...

21 CFR 316.30 - Annual reports of holder of orphan-drug designation.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 5 2010-04-01 2010-04-01 false Annual reports of holder of orphan-drug... SERVICES (CONTINUED) DRUGS FOR HUMAN USE ORPHAN DRUGS Designation of an Orphan Drug § 316.30 Annual reports of holder of orphan-drug designation. Within 14 months after the date on which a drug was designated...

12 CFR 563b.470 - Must I adjust liquidation sub-accounts?

Code of Federal Regulations, 2010 CFR

2010-01-01

... 12 Banks and Banking 5 2010-01-01 2010-01-01 false Must I adjust liquidation sub-accounts? 563b... liquidation sub-accounts? (a)(1) You must reduce the balance of an eligible account holder's or supplemental eligible account holder's sub-account if the deposit balance in the account holder's savings account at the...

7 CFR 4279.78 - Repurchase from holder.

Code of Federal Regulations, 2011 CFR

2011-01-01

... repurchase, less the lender's servicing fee, within 30 days after written demand to the Agency from the... portion of the loan from a holder within 30 days of written demand by the holder when the borrower is in default not less than 60 days on principal or interest due on the loan; or the lender has failed to remit...

7 CFR 4279.78 - Repurchase from holder.

Code of Federal Regulations, 2010 CFR

2010-01-01

... repurchase, less the lender's servicing fee, within 30 days after written demand to the Agency from the... portion of the loan from a holder within 30 days of written demand by the holder when the borrower is in default not less than 60 days on principal or interest due on the loan; or the lender has failed to remit...

7 CFR 3565.405 - Repurchase of guaranteed loans.

Code of Federal Regulations, 2014 CFR

2014-01-01

... Repurchase of guaranteed loans. (a) Repurchase by lender. The Holder may make written demand on the lender to... calendar days on principal or interest due on the loan; or the lender has failed to remit to the Holder its... of the loan or the note interest to the Holder on the guaranteed loan accruing after 90 calendar days...

7 CFR 3565.405 - Repurchase of guaranteed loans.

Code of Federal Regulations, 2013 CFR

2013-01-01

... Repurchase of guaranteed loans. (a) Repurchase by lender. The Holder may make written demand on the lender to... calendar days on principal or interest due on the loan; or the lender has failed to remit to the Holder its... of the loan or the note interest to the Holder on the guaranteed loan accruing after 90 calendar days...

7 CFR 3565.405 - Repurchase of guaranteed loans.

Code of Federal Regulations, 2012 CFR

2012-01-01

... Repurchase of guaranteed loans. (a) Repurchase by lender. The Holder may make written demand on the lender to... calendar days on principal or interest due on the loan; or the lender has failed to remit to the Holder its... of the loan or the note interest to the Holder on the guaranteed loan accruing after 90 calendar days...

17 CFR 270.32a-2 - Exemption for initial period from vote of security holders on independent public accountant for...

Code of Federal Regulations, 2013 CFR

2013-04-01

... from vote of security holders on independent public accountant for certain registered separate accounts... from vote of security holders on independent public accountant for certain registered separate accounts... 32(a) of the Act that selection of an independent public accountant shall have been submitted for...

17 CFR 270.32a-2 - Exemption for initial period from vote of security holders on independent public accountant for...

Code of Federal Regulations, 2014 CFR

2014-04-01

... from vote of security holders on independent public accountant for certain registered separate accounts... from vote of security holders on independent public accountant for certain registered separate accounts... 32(a) of the Act that selection of an independent public accountant shall have been submitted for...

17 CFR 270.32a-2 - Exemption for initial period from vote of security holders on independent public accountant for...

Code of Federal Regulations, 2012 CFR

2012-04-01

... from vote of security holders on independent public accountant for certain registered separate accounts... from vote of security holders on independent public accountant for certain registered separate accounts... 32(a) of the Act that selection of an independent public accountant shall have been submitted for...

17 CFR 270.32a-2 - Exemption for initial period from vote of security holders on independent public accountant for...

Code of Federal Regulations, 2011 CFR

2011-04-01

... from vote of security holders on independent public accountant for certain registered separate accounts... from vote of security holders on independent public accountant for certain registered separate accounts... 32(a) of the Act that selection of an independent public accountant shall have been submitted for...

A novel prototype 3/5 laparoscopic needle driver: A validation study with conventional laparoscopic needle driver.

PubMed

Ganpule, Arvind P; Deshmukh, Chaitanya S; Joshi, Tanmay

2018-01-01

The challenges in laparoscopic suturing include need to expertise to suture. Laparoscopic needle holder is a" key" instrument to accomplish this arduous task. The objective of this new invention was to develop a laparoscopic needle holder which would be adapted to avoid any wobble (with a shaft diameter same as a 5mm port), ensure accurate and dexterous suturing not just in adult patients but pediatric patients alike (with a short shaft diameter) and finally ensure seamless throw of knots with a narrow tip configuration. We did an initial evaluation to evaluate the validity of the prototype needle holder and its impact on laparoscopic suturing skills by experienced laparoscopic surgeons and novice laparoscopic Surgeons. Both the groups of surgeons performed two tasks. The first task was to grasp the needle and position it in an angle deemed ideal for suturing. The second task was to pass suture through two fixed points and make a single square knot. At the end of the tasks each participant was asked to complete a 5- point Likert's scale questionnaire (8 items; 4 items of handling and 4 items of suturing) rating each needle holder. In expert group, the mean time to complete task 1 was shorter with prototype 3/5 laparoscopic needle holder (11.8 sec Vs 20.8 sec). The mean time to complete task 2 was also shorter with prototype 3/5 laparoscopic needle holder (103.2 sec Vs 153.2 sec). In novice group, mean time to complete both the task was shorter with prototype 3/5 laparoscopic needle holder. The expert laparoscopic surgeons as well as novice laparoscopic surgeons performed laparoscopic suturing faster and with more ease while using the prototype 3/5 laparoscopic needle holder.

A novel prototype 3/5 laparoscopic needle driver: A validation study with conventional laparoscopic needle driver

PubMed Central

Ganpule, Arvind P.; Deshmukh, Chaitanya S.; Joshi, Tanmay

2018-01-01

Introduction: The challenges in laparoscopic suturing include need to expertise to suture. Laparoscopic needle holder is a ”key” instrument to accomplish this arduous task. Instrument: The objective of this new invention was to develop a laparoscopic needle holder which would be adapted to avoid any wobble (with a shaft diameter same as a 5mm port), ensure accurate and dexterous suturing not just in adult patients but pediatric patients alike (with a short shaft diameter) and finally ensure seamless throw of knots with a narrow tip configuration. Validation: We did an initial evaluation to evaluate the validity of the prototype needle holder and its impact on laparoscopic suturing skills by experienced laparoscopic surgeons and novice laparoscopic Surgeons. Both the groups of surgeons performed two tasks. The first task was to grasp the needle and position it in an angle deemed ideal for suturing. The second task was to pass suture through two fixed points and make a single square knot. At the end of the tasks each participant was asked to complete a 5- point Likert's scale questionnaire (8 items; 4 items of handling and 4 items of suturing) rating each needle holder. In expert group, the mean time to complete task 1 was shorter with prototype 3/5 laparoscopic needle holder (11.8 sec Vs 20.8 sec). The mean time to complete task 2 was also shorter with prototype 3/5 laparoscopic needle holder (103.2 sec Vs 153.2 sec). In novice group, mean time to complete both the task was shorter with prototype 3/5 laparoscopic needle holder. Conclusion: The expert laparoscopic surgeons as well as novice laparoscopic surgeons performed laparoscopic suturing faster and with more ease while using the prototype 3/5 laparoscopic needle holder. PMID:28782740

Social object play among young Japanese macaques (Macaca fuscata) in Arashiyama, Japan.

PubMed

Shimada, Masaki

2006-10-01

Social object play (SOP), i.e., social play using portable object(s), among young Japanese macaques (Macaca fuscata; 0-4 years old) in the Arashiyama E troop was studied using a modified sequence sampling method from July to October 2000. SOP was a relatively common activity for most of the young macaques and often continued for long periods. Participants used many kinds of object, including edible natural objects and artificial objects, such as plastic bottles, but they never used provisioned food or wild fruit in SOP bouts. An analysis of long bouts (>/=0.5 min) revealed the following interactive SOP features: (1) at any given time, participants used only one object, and only one participant held the object; (2) during SOP play-chasing, the object holder was likely to be chased by others; (3) during long bouts, the object changed hands frequently; and (4) agonistic competition for an object among young macaques was rare. Combinations of sexes, ages, relative ranks, or matrilines of the object holder and non-holder did not affect the tendency that the holder was chased by non-holder(s) during play-chasing. Even when there was a change in object holders, the repetitiveness of this interactive pattern, i.e., that the holder would be chased during SOP bouts, distinguished the SOP structure from that of other types of social play without object(s). General proximate social play mechanisms, such as self-handicapping or role taking, were associated with SOP. Other mechanisms that affected SOP included the following: (1) young macaques treated an object as a target in play competition, and (2) 'being the holder of a target object' was associated with the 'role of the chasee.'

Mechanical design of multiple zone plates precision alignment apparatus for hard X-ray focusing in twenty-nanometer scale

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shu, Deming; Liu, Jie; Gleber, Sophie C.

An enhanced mechanical design of multiple zone plates precision alignment apparatus for hard x-ray focusing in a twenty-nanometer scale is provided. The precision alignment apparatus includes a zone plate alignment base frame; a plurality of zone plates; and a plurality of zone plate holders, each said zone plate holder for mounting and aligning a respective zone plate for hard x-ray focusing. At least one respective positioning stage drives and positions each respective zone plate holder. Each respective positioning stage is mounted on the zone plate alignment base frame. A respective linkage component connects each respective positioning stage and the respectivemore » zone plate holder. The zone plate alignment base frame, each zone plate holder and each linkage component is formed of a selected material for providing thermal expansion stability and positioning stability for the precision alignment apparatus.« less

Stemless ball valve

NASA Technical Reports Server (NTRS)

Burgess, Kevin (Inventor); Yakos, David (Inventor); Walthall, Bryan (Inventor)

2012-01-01

A stemless ball valve comprising: a right flange; left flange; ball with an axis pin and two travel pins; ball seal on either side of the ball; guide sleeve with inner walls comprising two channels; cartridge guide holder; inner magnetic cartridge; and outer magnetic cartridge. The ball is situated inside of the guide sleeve, and a travel pin is located in each of the two channels. The guide sleeve is situated inside of the cartridge guide holder, which is located adjacent to and outside of the inner magnetic cartridge and secured to the inner magnetic cartridge such that when the inner magnetic cartridge rotates, the cartridge guide holder also rotates. The cartridge guide holder is secured to the guide sleeve such that when the cartridge guide holder rotates, the travel pins move within the channels in the inner walls of the guide sleeve, thereby causing the ball to rotate.

Development and positioning reliability of a TMS coil holder for headache research.

PubMed

Chronicle, Edward P; Pearson, A Jane; Matthews, Cheryl

2005-01-01

Accurate and reproducible coil positioning is important for headache research using transcranial magnetic stimulation protocols. We aimed to design a transcranial magnetic stimulation coil holder and demonstrate reliability of test-retest coil positioning. A coil holder was developed and manufactured according to three principles of stability, durability, and three-dimensional positional accuracy. Reliability of coil positioning was assessed by stimulating over the motor cortex of four neurologically normal subjects and recording finger muscle responses, both at a test phase and a retest phase several hours later. In all four subjects, repositioning of the transcranial magnetic stimulation coil solely on the basis of coil holder coordinates was accurate to within 2 mm. The coil holder demonstrated good test-retest reliability of coil positioning, and is thus a promising tool for transcranial magnetic stimulation-based headache research, particularly studies of prophylactic drug effect where several laboratory visits with identical coil positioning are necessary.

76 FR 77030 - Self-Regulatory Organizations; NYSE Amex LLC; Notice of Filing and Immediate Effectiveness of...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-09

... the NYSE Amex System, orders from the same ATP Holder may inadvertently execute against each other as a result of being entered by different persons and/or systems at the same ATP Holder. Therefore... of orders from the same ATP Holder within one second to be a violation of the exposure requirement...

26 CFR 301.6323(e)-1 - Priority of interest and expenses.

Code of Federal Regulations, 2010 CFR

2010-04-01

... interest is not subrogated to the rights of the holder of the State sales tax lien. However, if the holder...)-1, to the rights of the holder of the sales tax lien, he will also be entitled to any additional....6323(e)-1 Priority of interest and expenses. (a) In general. If the lien imposed by section 6321 is not...

26 CFR 1.1272-3 - Election by a holder to treat all interest on a debt instrument as OID.

Code of Federal Regulations, 2012 CFR

2012-04-01

..., OID, de minimis OID, market discount, de minimis market discount, and unstated interest, as adjusted... the rules provided by this section. (ii) Debt instrument with market discount. (A) A holder may make the election under this section for a debt instrument with market discount only if the holder is...

26 CFR 1.1272-3 - Election by a holder to treat all interest on a debt instrument as OID.

Code of Federal Regulations, 2014 CFR

2014-04-01

..., OID, de minimis OID, market discount, de minimis market discount, and unstated interest, as adjusted... the rules provided by this section. (ii) Debt instrument with market discount. (A) A holder may make the election under this section for a debt instrument with market discount only if the holder is...

26 CFR 1.1272-3 - Election by a holder to treat all interest on a debt instrument as OID.

Code of Federal Regulations, 2010 CFR

2010-04-01

..., market discount, de minimis market discount, and unstated interest, as adjusted by any amortizable bond... provided by this section. (ii) Debt instrument with market discount. (A) A holder may make the election under this section for a debt instrument with market discount only if the holder is eligible to make an...

26 CFR 1.1272-3 - Election by a holder to treat all interest on a debt instrument as OID.

Code of Federal Regulations, 2011 CFR

2011-04-01

..., OID, de minimis OID, market discount, de minimis market discount, and unstated interest, as adjusted... the rules provided by this section. (ii) Debt instrument with market discount. (A) A holder may make the election under this section for a debt instrument with market discount only if the holder is...

76 FR 20793 - Self-Regulatory Organizations; Chicago Board Options Exchange, Incorporated; Notice of Filing and...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-13

..., approximately 40% of CBOE Floor Broker Trading Permit Holders would fall under Tier 1 and would no longer be... Holders fall under Tier 4, having a PAR Official execute more than 75% of the Trading Permit Holder's... ``Exchange'') proposes to amend its Fees Schedule to establish volume threshold tiers for the assessment of...

75 FR 9982 - Self-Regulatory Organizations; The NASDAQ Stock Market LLC; Notice of Filing and Immediate...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-04

... Proposed Rule Change To Adopt a Round Lot Holder Initial Listing Requirement for Listing of Warrants on the... filing this proposed rule change to adopt a round lot holder requirement for listing on the Global and... Market Makers[.] ; and (d) In the case of warrants, there must be at least 400 Round Lot Holders (except...

Scholarly Productivity in Developing Countries: An Analysis of Levels and Patterns among Doctoral Holders in Uganda

ERIC Educational Resources Information Center

Wamala, Robert; Ssembatya, Vincent A.

2013-01-01

Doctoral holders are considered to be key actors in the creation of innovation and knowledge. However, this generalization may not hold true for doctoral holders in all countries. This study sought to assess the scholarly productivity of these highly qualified individuals in Uganda. The investigation is based on data sourced from the 2012 Careers…

75 FR 11734 - Damage Tolerance Data for Repairs and Alterations

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-12

....43(e) The change to Sec. 26.43(e) clarifies that this section does not apply to type certificate (TC... after January 11, 2008. This change is relieving to TC holders and does not impact a TC holder's ability to comply with Sec. 26.43(e). The FAA did not intend to require TC holders to develop repair...

42 CFR 60.42 - Records, reports, inspection, and audit requirements for HEAL lenders and holders.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 42 Public Health 1 2014-10-01 2014-10-01 false Records, reports, inspection, and audit requirements for HEAL lenders and holders. 60.42 Section 60.42 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES GRANTS HEALTH EDUCATION ASSISTANCE LOAN PROGRAM The Lender and Holder § 60.42 Records, reports, inspection, and audit...

A Mechanism for Anonymous Credit Card Systems

NASA Astrophysics Data System (ADS)

Tamura, Shinsuke; Yanase, Tatsuro

This paper proposes a mechanism for anonymous credit card systems, in which each credit card holder can conceal individual transactions from the credit card company, while enabling the credit card company to calculate the total expenditures of transactions of individual card holders during specified periods, and to identify card holders who executed dishonest transactions. Based on three existing mechanisms, i.e. anonymous authentication, blind signature and secure statistical data gathering, together with implicit transaction links proposed here, the proposed mechanism enables development of anonymous credit card systems without assuming any absolutely trustworthy entity like tamper resistant devices or organizations faithful both to the credit card company and card holders.

Method and apparatus for adjustably induced biaxial strain

DOEpatents

Vestel, Michael J.; Oshatz, Daryl Patrick

2006-05-16

An apparatus comprising a shape memory alloy is configured as a ring shaped sample holder for a transmission electron microscope and imparts uniform biaxial strain on a thin film mounted within. The sample holder responds to a change in temperature by changing the inner diameter, which imparts biaxial strain. In other embodiments, the sample holder is configured to change the inner diameter and change the strain on a thin film reversibly and repeatedly. In further embodiments, the sample holder is non circular. In still further embodiments, the apparatus is configured as a prime mover of a reversible radial actuator. Methods for making and using the apparatus are included in other embodiments.

77 FR 36027 - Self-Regulatory Organizations; NYSE Arca, Inc.; Notice of Filing and Immediate Effectiveness of...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-15

... Rates; and For Investor Tiers 1-3, the applicable rate based on an ETP Holder's qualifying levels. The... applicable Tier, Step Up Tier or Basic Rate and would be based on an ETP Holder's qualifying levels, as...-listed Tape B securities based on an ETP Holder's qualifying levels. $0.0026 per share fee for Tape B...

17 CFR 240.14a-7 - Obligations of registrants to provide a list of, or mail soliciting material to, security holders.

Code of Federal Regulations, 2013 CFR

2013-04-01

... Internet Availability of Proxy Materials (as described in § 240.14a-16), furnished by the security holder... security holder shall be sent to that address, provided that if multiple copies of the Notice of Internet... 17 Commodity and Securities Exchanges 3 2013-04-01 2013-04-01 false Obligations of registrants to...

17 CFR 240.14a-7 - Obligations of registrants to provide a list of, or mail soliciting material to, security holders.

Code of Federal Regulations, 2014 CFR

2014-04-01

... Internet Availability of Proxy Materials (as described in § 240.14a-16), furnished by the security holder... security holder shall be sent to that address, provided that if multiple copies of the Notice of Internet... 17 Commodity and Securities Exchanges 4 2014-04-01 2014-04-01 false Obligations of registrants to...

17 CFR 240.14a-7 - Obligations of registrants to provide a list of, or mail soliciting material to, security holders.

Code of Federal Regulations, 2011 CFR

2011-04-01

... Internet Availability of Proxy Materials (as described in § 240.14a-16), furnished by the security holder... security holder shall be sent to that address, provided that if multiple copies of the Notice of Internet... 17 Commodity and Securities Exchanges 3 2011-04-01 2011-04-01 false Obligations of registrants to...

17 CFR 240.14a-7 - Obligations of registrants to provide a list of, or mail soliciting material to, security holders.

Code of Federal Regulations, 2012 CFR

2012-04-01

... Internet Availability of Proxy Materials (as described in § 240.14a-16), furnished by the security holder... security holder shall be sent to that address, provided that if multiple copies of the Notice of Internet... 17 Commodity and Securities Exchanges 3 2012-04-01 2012-04-01 false Obligations of registrants to...

Decent wage is more important than absolution of debts: A smallholder socio-hydrological modelling framework

NASA Astrophysics Data System (ADS)

Pande, Saket; Savenije, Hubert

2015-04-01

We present a framework to understand the socio-hydrological system dynamics of a small holder. Small holders are farmers who own less than 2 ha of farmland. It couples the dynamics of 6 main variables that are most relevant at the scale of a small holder: local storage (soil moisture and other water storage), capital, knowledge, livestock production, soil fertility and grass biomass production. The hydroclimatic variability is at sub-annual scale and influences the socio-hydrology at annual scale. The model incorporates rule-based adaptation mechanisms (for example: adjusting expenditures on food and fertilizers, selling livestocks etc.) of small holders when they face adverse socio-hydrological conditions, such as low annual rainfall, higher intra-annual variability in rainfall or variability in agricultural prices. We apply the framework to understand the socio-hydrology of a sugarcane small holder in Aurangabad, Maharashtra. This district has witnessed suicides of many sugarcane farmers who could not extricate themselves out of the debt trap. These farmers lack irrigation and are susceptible to fluctuating sugar prices and intra-annual hydro-climatic variability. We study the sensitivity of annual total capital averaged over 30 years, an indicator of small holder wellbeing, to initial capital that a small holder starts with and the prevalent wage rates. We find that a smallholder well being is low (below Rs 30000 per annum, a threshold above which a smallholder can afford a basic standard of living) and is rather insensitive to initial capital at low wage rates. Initial capital perhaps matters to small holder livelihoods at higher wage rates. Further, the small holder system appears to be resilient at around Rs 115/mandays in the sense that small perturbations in wage rates around this rate still sustains the smallholder above the basic standard of living. Our results thus indicate that government intervention to absolve the debt of farmers is not enough. It must invest in local storages that can buffer intra-annual variability in rainfall in tandem and good wages for alternative sources of income.

Preparation of Regular Specimens for Atom Probes

NASA Technical Reports Server (NTRS)

Kuhlman, Kim; Wishard, James

2003-01-01

A method of preparation of specimens of non-electropolishable materials for analysis by atom probes is being developed as a superior alternative to a prior method. In comparison with the prior method, the present method involves less processing time. Also, whereas the prior method yields irregularly shaped and sized specimens, the present developmental method offers the potential to prepare specimens of regular shape and size. The prior method is called the method of sharp shards because it involves crushing the material of interest and selecting microscopic sharp shards of the material for use as specimens. Each selected shard is oriented with its sharp tip facing away from the tip of a stainless-steel pin and is glued to the tip of the pin by use of silver epoxy. Then the shard is milled by use of a focused ion beam (FIB) to make the shard very thin (relative to its length) and to make its tip sharp enough for atom-probe analysis. The method of sharp shards is extremely time-consuming because the selection of shards must be performed with the help of a microscope, the shards must be positioned on the pins by use of micromanipulators, and the irregularity of size and shape necessitates many hours of FIB milling to sharpen each shard. In the present method, a flat slab of the material of interest (e.g., a polished sample of rock or a coated semiconductor wafer) is mounted in the sample holder of a dicing saw of the type conventionally used to cut individual integrated circuits out of the wafers on which they are fabricated in batches. A saw blade appropriate to the material of interest is selected. The depth of cut and the distance between successive parallel cuts is made such that what is left after the cuts is a series of thin, parallel ridges on a solid base. Then the workpiece is rotated 90 and the pattern of cuts is repeated, leaving behind a square array of square posts on the solid base. The posts can be made regular, long, and thin, as required for samples for atom-probe analysis. Because of their small volume and regularity, the amount of FIB-milling time can be much less than that of the method of sharp shards. Individual posts can be broken off for mounting in a manner similar to that of the method of sharp shards. Alternatively, the posts can be left intact on the base and the base can be cut to a small square (e.g., 3 by 3 mm) suitable for mounting in an atom probe of a type capable of accepting multiple-tip specimens. The advantage of multiple-tip specimens is the possibility of analyzing many tips without the time-consuming interchange of specimens.

Micro electro-mechanical heater

DOEpatents

Oh, Yunje; Asif, Syed Amanulla Syed; Cyrankowski, Edward; Warren, Oden Lee

2016-04-19

A sub-micron scale property testing apparatus including a test subject holder and heating assembly. The assembly includes a holder base configured to couple with a sub-micron mechanical testing instrument and electro-mechanical transducer assembly. The assembly further includes a test subject stage coupled with the holder base. The test subject stage is thermally isolated from the holder base. The test subject stage includes a stage subject surface configured to receive a test subject, and a stage plate bracing the stage subject surface. The stage plate is under the stage subject surface. The test subject stage further includes a heating element adjacent to the stage subject surface, the heating element is configured to generate heat at the stage subject surface.

Micro electro-mechanical heater

DOEpatents

Oh, Yunje; Asif, Syed Amanulla Syed; Cyrankowski, Edward; Warren, Oden Lee

2017-09-12

A sub-micron scale property testing apparatus including a test subject holder and heating assembly. The assembly includes a holder base configured to couple with a sub-micron mechanical testing instrument and electro-mechanical transducer assembly. The assembly further includes a test subject stage coupled with the holder base. The test subject stage is thermally isolated from the holder base. The test subject stage includes a stage subject surface configured to receive a test subject, and a stage plate bracing the stage subject surface. The stage plate is under the stage subject surface. The test subject stage further includes a heating element adjacent to the stage subject surface, the heating element is configured to generate heat at the stage subject surface.

Ignitability test method and apparatus

NASA Technical Reports Server (NTRS)

Bement, Laurence J. (Inventor); Bailey, James W. (Inventor); Schimmel, Morry L. (Inventor)

1989-01-01

An apparatus for testing ignitability of an initiator includes a body with a central cavity, initiator holder for holding the initiator over the central cavity of the body, an ignition material holder disposed in the central cavity of the body and a cavity facing the initiator holder which receives a measured quantity of ignition material to be ignited by the initiator and a chamber in communication with the cavity of the ignition material holder and the central cavity of the body. A measuring system for analyzing pressure characteristics is generated by ignition material by the initiator. The measuring system includes at least one transducer coupled to an oscillograph for recording pressure traces generated by ignition.

System and method for assaying radiation

DOEpatents

DiPrete, David P; Whiteside, Tad; Pak, Donald J; DiPrete, Cecilia C

2013-11-12

A system for assaying radiation includes a sample holder configured to hold a liquid scintillation solution. A photomultiplier receives light from the liquid scintillation solution and generates a signal reflective of the light. A control circuit biases the photomultiplier and receives the signal from the photomultiplier reflective of the light. A light impermeable casing surrounds the sample holder, photomultiplier, and control circuit. A method for assaying radiation includes placing a sample in a liquid scintillation solution, placing the liquid scintillation solution in a sample holder, and placing the sample holder inside a light impermeable casing. The method further includes positioning a photomultiplier inside the light impermeable casing and supplying power to a control circuit inside the light impermeable casing.

Correlation between porosity and space holder content at different sintering temperatures of aluminum foam

NASA Astrophysics Data System (ADS)

Rushdi, N. M. F. M.; Jamaludin, S. B.; Mazlee, M. N.; Jamal, Z. A. Z.

2016-07-01

Aluminum foam is the most popular metal foam that can be used as energy absorbers, heat exchangers, air-oil separators and structure core of fuel cells. Melt-foaming agent, melt-gas injection, investment casting and powder-foaming agent techniques can be used to manufacture aluminum foam, but these techniques are too expensive. In this study, the aluminum foam was manufactured via a sintering dissolution process (SDP). Powders of aluminum and sodium chloride as space holder (25, 40, 50 wt. %) were mixed together to produce a homogeneous mixture. The mixture was compacted at 200 MPa followed by sintering at 500, 550 and 600˚C for 2 hours. A warm running water stream was used to dissolve the space holder that was embedded in the aluminum. The result showed that, the space holder content performed a significant role to control the total porosity to a value between 18 and 40%, and the porosity increased with increasing content of space holder and sintering temperature.

Ebola Virus and Marburg Virus in Human Milk Are Inactivated by Holder Pasteurization.

PubMed

Hamilton Spence, Erin; Huff, Monica; Shattuck, Karen; Vickers, Amy; Yun, Nadezda; Paessler, Slobodan

2017-05-01

Potential donors of human milk are screened for Ebola virus (EBOV) using standard questions, but testing for EBOV and Marburg virus (MARV) is not part of routine serological testing performed by milk banks. Research aim: This study tested the hypothesis that EBOV would be inactivated in donor human milk (DHM) by standard pasteurization techniques (Holder) used in all North American nonprofit milk banks. Milk samples were obtained from a nonprofit milk bank. They were inoculated with EBOV (Zaire strain) and MARV (Angola strain) and processed by standard Holder pasteurization technique. Plaque assays for EBOV and MARV were performed to detect the presence of virus after pasteurization. Neither EBOV nor MARV was detectable by viral plaque assay in DHM or culture media samples, which were pasteurized by the Holder process. EBOV and MARV are safely inactivated in human milk by standard Holder pasteurization technique. Screening for EBOV or MARV beyond questionnaire and self-deferral is not needed to ensure safety of DHM for high-risk infants.

Apparatus for afterburning the exhaust gases of an internal combustion engine to remove pollutants therefrom

DOE Office of Scientific and Technical Information (OSTI.GOV)

Laurent, P.A.

1976-09-28

An apparatus is described for afterburning the combustible pollutants from the exhaust gases of an internal combustion engine in a reactor, in which secondary air is introduced. Upstream of the reactor, a chamber in the form of a torus is provided, through which the exhaust gases from a maximum number of cylinders flow before entering the reactor. A first obstacle, acting as a flame holder is disposed inside the torus. The reactor comprises a chamber whose inner surface is approximately a surface of revolution, and mounted inside of which is a second obstacle, acting as flame holder, substantially along themore » axis of revolution. The second flame holder has a diameter large enough to provide a contact time of 1 to 3 x 10/sup -3/ seconds of the gas flow in a recirculation zone surrounding the second flame holder, the diameter of the second flame holder being 15 to 40 percent of the reactor diameter.« less

The Burden of Power: Construing Power as Responsibility (Rather Than as Opportunity) Alters Threat-Challenge Responses.

PubMed

Scholl, Annika; de Wit, Frank; Ellemers, Naomi; Fetterman, Adam K; Sassenberg, Kai; Scheepers, Daan

2018-07-01

Power usually lowers stress responses. In stressful situations, having high (vs. low) power heightens challenge and lowers threat. Yet, even power-holders may experience threat when becoming aware of the responsibility that accompanies their power. Power-holders can construe (i.e., understand) a high-power position primarily as opportunity to "make things happen" or as responsibility to "take care of things." Power-holders construing power as responsibility (rather than opportunity) may be more likely to experience demands-such as taking care of important decisions under their control-as outweighing their resources, resulting in less challenge and more threat. Four experiments with subjective and cardiovascular threat-challenge indicators support this. Going beyond prior work on structural aspects (e.g., power instability) that induce stress, we show that merely the way how power-holders construe their power can evoke stress. Specifically, we find that power construed as responsibility (vs. opportunity) is more likely to imply a "burden" for the power-holder.

The Effect of UV-C Pasteurization on Bacteriostatic Properties and Immunological Proteins of Donor Human Milk

PubMed Central

Christen, Lukas; Lai, Ching Tat; Hartmann, Ben; Hartmann, Peter E.; Geddes, Donna T.

2013-01-01

Background Human milk possesses bacteriostatic properties, largely due to the presence of immunological proteins. Heat treatments such as Holder pasteurization reduce the concentration of immunological proteins in human milk and consequently increase the bacterial growth rate. This study investigated the bacterial growth rate and the immunological protein concentration of ultraviolet (UV-C) irradiated, Holder pasteurized and untreated human milk. Methods Samples (n=10) of untreated, Holder pasteurized and UV-C irradiated human milk were inoculated with E. coli and S. aureus and the growth rate over 2 hours incubation time at 37°C was observed. Additionally, the concentration of sIgA, lactoferrin and lysozyme of untreated and treated human milk was analyzed. Results The bacterial growth rate of untreated and UV-C irradiated human milk was not significantly different. The bacterial growth rate of Holder pasteurized human milk was double compared to untreated human milk (p<0.001). The retention of sIgA, lactoferrin and lysozyme after UV-C irradiation was 89%, 87%, and 75% respectively, which were higher than Holder treated with 49%, 9%, and 41% respectively. Conclusion UV-C irradiation of human milk preserves significantly higher levels of immunological proteins than Holder pasteurization, resulting in bacteriostatic properties similar to those of untreated human milk. PMID:24376898

The effect of UV-C pasteurization on bacteriostatic properties and immunological proteins of donor human milk.

PubMed

Christen, Lukas; Lai, Ching Tat; Hartmann, Ben; Hartmann, Peter E; Geddes, Donna T

2013-01-01

Human milk possesses bacteriostatic properties, largely due to the presence of immunological proteins. Heat treatments such as Holder pasteurization reduce the concentration of immunological proteins in human milk and consequently increase the bacterial growth rate. This study investigated the bacterial growth rate and the immunological protein concentration of ultraviolet (UV-C) irradiated, Holder pasteurized and untreated human milk. Samples (n=10) of untreated, Holder pasteurized and UV-C irradiated human milk were inoculated with E. coli and S. aureus and the growth rate over 2 hours incubation time at 37°C was observed. Additionally, the concentration of sIgA, lactoferrin and lysozyme of untreated and treated human milk was analyzed. The bacterial growth rate of untreated and UV-C irradiated human milk was not significantly different. The bacterial growth rate of Holder pasteurized human milk was double compared to untreated human milk (p<0.001). The retention of sIgA, lactoferrin and lysozyme after UV-C irradiation was 89%, 87%, and 75% respectively, which were higher than Holder treated with 49%, 9%, and 41% respectively. UV-C irradiation of human milk preserves significantly higher levels of immunological proteins than Holder pasteurization, resulting in bacteriostatic properties similar to those of untreated human milk.

Further improvement of an intraocular lens holder for more physiological measurements within a mechanical eye model

NASA Astrophysics Data System (ADS)

Reutterer, Bernd; Traxler, Lukas; Bayer, Natascha; Drauschke, Andreas

2017-04-01

To evaluate the performance of intraocular lenses to treat cataract, an optomechanical eye model was developed. One of the most crucial components is the IOL holder, which should guarantee a physiological representation of the capsular bag and a stable position during measurement sequences. Individual holders are required due to the fact that every IOL has different geometric parameters. A method which allows obtaining the correct dimensions for the holder of a special IOL was developed and tested, by verifying the position of the IOL before and after a measurement sequence. Results of telecentric measurements and MTF measurements show that the IOL position does not change during the displacement sequence induced by the stepper motors of the eye model.

Thermal Stress FE Analysis of Large-scale Gas Holder Under Sunshine Temperature Field

NASA Astrophysics Data System (ADS)

Li, Jingyu; Yang, Ranxia; Wang, Hehui

2018-03-01

The temperature field and thermal stress of Man type gas holder is simulated by using the theory of sunshine temperature field based on ASHRAE clear-sky model and the finite element method. The distribution of surface temperature and thermal stress of gas holder under the given sunshine condition is obtained. The results show that the thermal stress caused by sunshine can be identified as one of the important factors for the failure of local cracked oil leakage which happens on the sunny side before on the shady side. Therefore, it is of great importance to consider the sunshine thermal load in the stress analysis, design and operation of large-scale steel structures such as the gas holder.

Microbial flora of tears of orthokeratology patients, and microbial contamination of contact lenses and contact lens accessories.

PubMed

Boost, Maureen V; Cho, Pauline

2005-06-01

The purpose of this study is to determine if there are changes in the ocular flora of overnight orthokeratology (ortho-k) patients, and the levels of contamination of their lenses and lens accessories, and to correlate compliance with levels of contamination. Normal ocular flora of 41 subjects was determined twice before commencing ortho-k lens wear by culture of the lower conjunctiva. Further specimens were collected on six follow-up visits after beginning lens wear, as were samples from their lenses, cases, and suction holders. A questionnaire on lens care was administered after the fifth visit. Three subjects provided conjunctival samples yielding Staphylococcus aureus on one occasion before lens wear, one being positive for this organism after beginning lens wear. Of 38 subjects yielding no growth or only normal eye flora before use, 28 remained free of ocular pathogens after beginning lens wear. Only four subjects had positive cultures on more than one occasion after lens wear. There was no significant difference in isolation levels of pathogens with lens wear (p = 0.423). Lens culture of 54% of subjects yielded no growth or normal flora only; lenses of 16 subjects yielded potential pathogens, including three subjects contaminated on more than one occasion. Lens isolates did not match the organisms transiently colonizing the eye. Lens case, the most frequently contaminated item, was associated with lens contamination (p < 0.001), the same organism being isolated from both items in 11 subjects. Lens suction holder was less frequently contaminated. Neither lens case nor suction holder contamination was associated with isolates from the eye. Reported good compliance correlated with lack of contamination in all but one subject. The most frequent breaches in the lens care protocol were failure to clean, disinfect, and replace the lens case. Ocular flora was not altered by ortho-k lens wear over an extended period, and patients remained free of infection. Contaminants identified were generally of a transient nature. Most patients had significant contamination of at least one item, most frequently the lens case. Lens case isolates were significantly associated with those from the lens. The majority of patients reporting good compliance had low or no contamination of their lenses and accessories.

Research Amplitudo Vibration On Holder Due To The Process Of Lathe Nozzle Rocket RX 450

NASA Astrophysics Data System (ADS)

Ediwan; Budi Djatmiko, Agus; Dody Arisandi, EfFendy; Purnomo, Heri; Ibadi, Mahfud

2018-04-01

The main function of the rocket nozzle is to convert the enthalpy efficiency from combustion gas to kinetic energy and also to make high velocity out of the gas. The rocket nozzle usually consists of a converging and diverging part. With a smaller area on the neck and enlarged at the exit area. The velocity flow through the nozzle enlarges into the speed of sound through the neck and then becomes super sonic in the divergent part. Nozzle making or machining using conventional lathes, first performed is drilling on a massive metal that is bonded to the veneer, then after a sufficient gap is done deep-boring. At the time of the process of lathe in the nozzle RX 450 there is an obstacle that is vibrating tool holder chisel or holder so it is worried about not precision of the process of lathe. This should not happen because it can cause failure in the latter for it needs to be studied and studied further so that the lathe process goes accordingly. The holder material of ST 60 with a modulus of elasticity 200 GPa and a nozzle material of AISI 4340 alloy steel with σyield = 470 MPa, Shear Modulus G = 80 GPa. The purpose of this research is to observe the amplitude of vibration on the holder due to RX- 450 nozzle lathe processing for the purpose of amplitude that occurs in accordance with the desired so that the nozzle structure is no damage process. The result of the research was obtained holder with length (L) 80cm, profile width (B) 5 cm, height of profile (H) 10 cm, turning machine ω = 8.98 rad / sec and natural holder frequency ωn = 89.8 rad / second, Amplitude of vibration of δ = 1.21 mm, while the amplitude of the design X = 1.22 mm From the results of this study it can be said that the holder of a chisel or holder can be used as a tool at the time of RX nozzle retrieval process and is quite safe because it works under the condition ω/ω n <0 3 (Plans and Specifications of A Suborbital Rocket Payload "AKPV Engineering University of Wyoming 2009 )

Evaluation of Cooling Conditions for a High Heat Flux Testing Facility Based on Plasma-Arc Lamps

DOE PAGES

Charry, Carlos H.; Abdel-khalik, Said I.; Yoda, Minami; ...

2015-07-31

The new Irradiated Material Target Station (IMTS) facility for fusion materials at Oak Ridge National Laboratory (ORNL) uses an infrared plasma-arc lamp (PAL) to deliver incident heat fluxes as high as 27 MW/m 2. The facility is being used to test irradiated plasma-facing component materials as part of the joint US-Japan PHENIX program. The irradiated samples are to be mounted on molybdenum sample holders attached to a water-cooled copper rod. Depending on the size and geometry of samples, several sample holders and copper rod configurations have been fabricated and tested. As a part of the effort to design sample holdersmore » compatible with the high heat flux (HHF) testing to be conducted at the IMTS facility, numerical simulations have been performed for two different water-cooled sample holder designs using the ANSYS FLUENT 14.0 commercial computational fluid dynamics (CFD) software package. The primary objective of this work is to evaluate the cooling capability of different sample holder designs, i.e. to estimate their maximum allowable incident heat flux values. 2D axisymmetric numerical simulations are performed using the realizable k-ε turbulence model and the RPI nucleate boiling model within ANSYS FLUENT 14.0. The results of the numerical model were compared against the experimental data for two sample holder designs tested in the IMTS facility. The model has been used to parametrically evaluate the effect of various operational parameters on the predicted temperature distributions. The results were used to identify the limiting parameter for safe operation of the two sample holders and the associated peak heat flux limits. The results of this investigation will help guide the development of new sample holder designs.« less

A Smallholder Socio-hydrological Modelling Framework

NASA Astrophysics Data System (ADS)

Pande, S.; Savenije, H.; Rathore, P.

2014-12-01

Small holders are farmers who own less than 2 ha of farmland. They often have low productivity and thus remain at subsistence level. A fact that nearly 80% of Indian farmers are smallholders, who merely own a third of total farmlands and belong to the poorest quartile, but produce nearly 40% of countries foodgrains underlines the importance of understanding the socio-hydrology of a small holder. We present a framework to understand the socio-hydrological system dynamics of a small holder. It couples the dynamics of 6 main variables that are most relevant at the scale of a small holder: local storage (soil moisture and other water storage), capital, knowledge, livestock production, soil fertility and grass biomass production. The model incorporates rule-based adaptation mechanisms (for example: adjusting expenditures on food and fertilizers, selling livestocks etc.) of small holders when they face adverse socio-hydrological conditions, such as low annual rainfall, higher intra-annual variability in rainfall or variability in agricultural prices. It allows us to study sustainability of small holder farming systems under various settings. We apply the framework to understand the socio-hydrology of small holders in Aurangabad, Maharashtra, India. This district has witnessed suicides of many sugarcane farmers who could not extricate themselves out of the debt trap. These farmers lack irrigation and are susceptible to fluctuating sugar prices and intra-annual hydroclimatic variability. This presentation discusses two aspects in particular: whether government interventions to absolve the debt of farmers is enough and what is the value of investing in local storages that can buffer intra-annual variability in rainfall and strengthening the safety-nets either by creating opportunities for alternative sources of income or by crop diversification.

FlexED8: the first member of a fast and flexible sample-changer family for macromolecular crystallography.

PubMed

Papp, Gergely; Felisaz, Franck; Sorez, Clement; Lopez-Marrero, Marcos; Janocha, Robert; Manjasetty, Babu; Gobbo, Alexandre; Belrhali, Hassan; Bowler, Matthew W; Cipriani, Florent

2017-10-01

Automated sample changers are now standard equipment for modern macromolecular crystallography synchrotron beamlines. Nevertheless, most are only compatible with a single type of sample holder and puck. Recent work aimed at reducing sample-handling efforts and crystal-alignment times at beamlines has resulted in a new generation of compact and precise sample holders for cryocrystallography: miniSPINE and NewPin [see the companion paper by Papp et al. (2017, Acta Cryst., D73, 829-840)]. With full data collection now possible within seconds at most advanced beamlines, and future fourth-generation synchrotron sources promising to extract data in a few tens of milliseconds, the time taken to mount and centre a sample is rate-limiting. In this context, a versatile and fast sample changer, FlexED8, has been developed that is compatible with the highly successful SPINE sample holder and with the miniSPINE and NewPin sample holders. Based on a six-axis industrial robot, FlexED8 is equipped with a tool changer and includes a novel open sample-storage dewar with a built-in ice-filtering system. With seven versatile puck slots, it can hold up to 112 SPINE sample holders in uni-pucks, or 252 miniSPINE or NewPin sample holders, with 36 samples per puck. Additionally, a double gripper, compatible with the SPINE sample holders and uni-pucks, allows a reduction in the sample-exchange time from 40 s, the typical time with a standard single gripper, to less than 5 s. Computer vision-based sample-transfer monitoring, sophisticated error handling and automatic error-recovery procedures ensure high reliability. The FlexED8 sample changer has been successfully tested under real conditions on a beamline.

Lathe tool bit and holder for machining fiberglass materials

NASA Technical Reports Server (NTRS)

Winn, L. E. (Inventor)

1972-01-01

A lathe tool and holder combination for machining resin impregnated fiberglass cloth laminates is described. The tool holder and tool bit combination is designed to accommodate a conventional carbide-tipped, round shank router bit as the cutting medium, and provides an infinite number of cutting angles in order to produce a true and smooth surface in the fiberglass material workpiece with every pass of the tool bit. The technique utilizes damaged router bits which ordinarily would be discarded.

50 CFR 665.803 - Notifications.

Code of Federal Regulations, 2010 CFR

2010-10-01

... notification of the trip type (either deep-setting or shallow-setting). (b) The permit holder, or designated... in processing an application, permit holders failing to receive important notifications, or sanctions...

Research on the tool holder mode in high speed machining

NASA Astrophysics Data System (ADS)

Zhenyu, Zhao; Yongquan, Zhou; Houming, Zhou; Xiaomei, Xu; Haibin, Xiao

2018-03-01

High speed machining technology can improve the processing efficiency and precision, but also reduce the processing cost. Therefore, the technology is widely regarded in the industry. With the extensive application of high-speed machining technology, high-speed tool system has higher and higher requirements on the tool chuck. At present, in high speed precision machining, several new kinds of clip heads are as long as there are heat shrinkage tool-holder, high-precision spring chuck, hydraulic tool-holder, and the three-rib deformation chuck. Among them, the heat shrinkage tool-holder has the advantages of high precision, high clamping force, high bending rigidity and dynamic balance, etc., which are widely used. Therefore, it is of great significance to research the new requirements of the machining tool system. In order to adapt to the requirement of high speed machining precision machining technology, this paper expounds the common tool holder technology of high precision machining, and proposes how to select correctly tool clamping system in practice. The characteristics and existing problems are analyzed in the tool clamping system.

Double acting bit holder

DOEpatents

Morrell, Roger J.; Larson, David A.; Ruzzi, Peter L.

1994-01-01

A double acting bit holder that permits bits held in it to be resharpened during cutting action to increase energy efficiency by reducing the amount of small chips produced. The holder consist of: a stationary base portion capable of being fixed to a cutter head of an excavation machine and having an integral extension therefrom with a bore hole therethrough to accommodate a pin shaft; a movable portion coextensive with the base having a pin shaft integrally extending therefrom that is insertable in the bore hole of the base member to permit the moveable portion to rotate about the axis of the pin shaft; a recess in the movable portion of the holder to accommodate a shank of a bit; and a biased spring disposed in adjoining openings in the base and moveable portions of the holder to permit the moveable portion to pivot around the pin shaft during cutting action of a bit fixed in a turret to allow front, mid and back positions of the bit during cutting to lessen creation of small chip amounts and resharpen the bit during excavation use.

System for loading slab-gel holders for electrophoresis separation

DOEpatents

Anderson, Norman G.; Anderson, Norman L.

1979-01-01

A slab-gel loading system includes a prismatic chamber for filling a plurality of slab-gel holders simultaneously. Each slab-gel holder comprises a pair of spaced apart plates defining an intermediate volume for gel containment. The holders are vertically positioned in the chamber with their major surfaces parallel to the chamber end walls. A liquid inlet is provided at the corner between the bottom and a side wall of the chamber for distributing a polymerizable monomer solution or a coagulable colloidal solution into each of the holders. The chamber is rotatably supported so that filling can begin with the corner having the liquid inlet directed downwardly such that the solution is gently funneled upwardly, without mixing, along the diverging side and bottom surfaces. As filling proceeds, the chamber is gradually rotated to position the bottom wall in a horizontal mode. The liquid filling means includes a plastic envelope with a septum dividing it into two compartments for intermixing two solutions of different density and thereby providing a liquid flow having a density gradient. The resulting gels have a density gradient between opposite edges for subsequent use in electrophoresis separations.

Double-tilt in situ TEM holder with ultra-high stability.

PubMed

Xu, Mingjie; Dai, Sheng; Blum, Thomas; Li, Linze; Pan, Xiaoqing

2018-05-06

A double tilting holder with high stability is essential for acquiring atomic-scale information by transmission electron microscopy (TEM), but the availability of such holders for in situ TEM studies under various external stimuli is limited. Here, we report a unique design of seal-bearing components that provides ultra-high stability and multifunctionality (including double tilting) in an in situ TEM holder. The seal-bearing subsystem provides superior vibration damping and electrical insulation while maintaining excellent vacuum sealing and small form factor. A wide variety of in situ TEM applications including electrical measurement, STM mapping, photovoltaic studies, and CL spectroscopy can be performed on this platform with high spatial resolution imaging and electrical sensitivity at the pA scale. Copyright © 2018 Elsevier B.V. All rights reserved.

Note: A sample holder design for sensitive magnetic measurements at high temperatures in a magnetic properties measurement system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arauzo, A.; Guerrero, E.; Urtizberea, A.

2012-06-15

A sample holder design for high temperature measurements in a commercial MPMS SQUID magnetometer from Quantum Design is presented. It fulfills the requirements for the simultaneous use of the oven and reciprocating sample option (RSO) options, thus allowing sensitive magnetic measurements up to 800 K. Alternating current susceptibility can also be measured, since the holder does not induce any phase shift relative to the ac driven field. It is easily fabricated by twisting Constantan Copyright-Sign wires into a braid nesting the sample inside. This design ensures that the sample be placed tightly into a tough holder with its orientation fixed,more » and prevents any sample displacement during the fast movements of the RSO transport, up to high temperatures.« less

Braking system for use with an arbor of a microscope

DOEpatents

Norgren, Duane U.

1984-01-01

A balanced braking system comprising a plurality of braking assemblies located about a member to be braked. Each of the braking assemblies consists of a spring biased piston of a first material fitted into a body of a different material which has a greater contraction upon cooling than the piston material. The piston is provided with a recessed head portion over which is positioned a diaphragm and forming a space therebetween to which is connected a pressurized fluid supply. The diaphragm is controlled by the fluid in the space to contact or withdraw from the member to be braked. A cooling device causes the body within which the piston is fitted to contract more than the piston, producing a tight shrink fit therebetween. The braking system is particularly applicable for selectively braking an arbor of an electron microscope which immobilizes, for example, a vertically adjustable low temperature specimen holder during observation. The system provides balanced braking forces which can be easily removed and re-established with minimal disturbance to arbor location.

An Apparatus for the Simultaneous Measurements of Thermal Conductivity, Thermal Expansion and Thermal Diffusivity of FRPs Using GM Refrigerator

NASA Astrophysics Data System (ADS)

Kanagaraj, S.; Pattanayak, S.

2004-06-01

The applications of fibre reinforced plastic (FRP) materials in cryogenic engineering have stimulated keen interest in the investigation of its properties. The reliable design data generated by a precisely controlled setup at identical environment of its applications are extremely important. This paper describes an apparatus based on a GM refrigerator for the simultaneous measurements of thermal conductivity, thermal expansion and thermal diffusivity using a double-specimen guarded-hotplate, 3-terminal capacitance technique and Angstrom method respectively in the temperature range from 30 K to 300 K. An integrated and perfectly insulated sample holder is designed and fabricated in such a way that the simultaneous measurements of the above properties are conveniently and accurately carried out at different temperatures. A set of stability criteria has been followed during the measurements to ensure the accuracy of the experimental data. The setup is calibrated with stainless steel and copper and the experimental results are within 10 % of the published results given in the literatures.

Functional Performances of CuZnAl Shape Memory Alloy Open-Cell Foams

NASA Astrophysics Data System (ADS)

Biffi, C. A.; Casati, R.; Bassani, P.; Tuissi, A.

2018-01-01

Shape memory alloys (SMAs) with cellular structure offer a unique mixture of thermo-physical-mechanical properties. These characteristics can be tuned by changing the pore size and make the shape memory metallic foams very attractive for developing new devices for structural and functional applications. In this work, CuZnAl SMA foams were produced through the liquid infiltration of space holder method. In comparison, a conventional CuZn brass alloy was foamed trough the same method. Functional performances were studied on both bulk and foamed SMA specimens. Calorimetric response shows similar martensitic transformation (MT) below 0 °C. Compressive response of CuZnAl revealed that mechanical behavior is strongly affected by sample morphology and that damping capacity of metallic foam is increased above the MT temperatures. The shape memory effect was detected in the CuZnAl foams. The conventional brass shows a compressive response similar to that of the martensitic CuZnAl, in which plastic deformation accumulation occurs up to the cellular structure densification after few thermal cycles.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ranson, W.F.; Schaeffel, J.A.; Murphree, E.A.

The response of prestressed and preheated plates subject to an exponentially decaying blast load was experimentally determined. A grid was reflected from the front surface of the plate and the response was recorded with a high speed camera. The camera used in this analysis was a rotating drum camera operating at 20,000 frames per second with a maximum of 224 frames at 39 microseconds separation. Inplane tension loads were applied to the plate by means of air cylinders. Maximum biaxial load applied to the plate was 500 pounds. Plate preheating was obtained with resistance heaters located in the specimen platemore » holder with a maximum capability of 500F. Data analysis was restricted to the maximum conditions at the center of the plate. Strains were determined from the photographic data and the stresses were calculated from the strain data. Results were obtained from zero preload conditions to a maximum of 480 pounds inplane tension loads and a plate temperature of 490F. The blast load ranged from 6 to 23 psi.« less

Braking system

DOEpatents

Norgren, D.U.

1982-09-23

A balanced braking system comprising a plurality of braking assemblies located about a member to be braked. Each of the braking assemblies consists of a spring biased piston of a first material fitted into a body of a different material which has a greater contraction upon cooling than the piston material. The piston is provided with a recessed head portion over which is positioned a diaphragm and forming a space therebetween to which is connected a pressurized fluid supply. The diaphragm is controlled by the fluid in the space to contact or withdraw from the member to be braked. A cooling means causes the body within which the piston is fitted to contract more than the piston, producing a tight shrink fit therebetween. The braking system is particularly applicable for selectively braking an arbor of an electron microscope which immobilizes, for example, a vertically adjustable low temperature specimen holder during observation. The system provides balanced braking forces which can be easily removed and re-established with minimal disturbance to arbor location.

50 CFR 25.57 - Exceptions and exemptions.

Code of Federal Regulations, 2014 CFR

2014-10-01

...) Persons accompanying the holder of a valid single visit permit, Federal Duck Stamp or Golden Eagle, Age..., children, or parents accompanying the holder of a valid single visit permit, Federal Duck Stamp or Golden...

50 CFR 25.57 - Exceptions and exemptions.

Code of Federal Regulations, 2010 CFR

2010-10-01

...) Persons accompanying the holder of a valid single visit permit, Federal Duck Stamp or Golden Eagle, Age..., children, or parents accompanying the holder of a valid single visit permit, Federal Duck Stamp or Golden...

50 CFR 25.57 - Exceptions and exemptions.

Code of Federal Regulations, 2011 CFR

2011-10-01

...) Persons accompanying the holder of a valid single visit permit, Federal Duck Stamp or Golden Eagle, Age..., children, or parents accompanying the holder of a valid single visit permit, Federal Duck Stamp or Golden...

50 CFR 25.57 - Exceptions and exemptions.

Code of Federal Regulations, 2013 CFR

2013-10-01

...) Persons accompanying the holder of a valid single visit permit, Federal Duck Stamp or Golden Eagle, Age..., children, or parents accompanying the holder of a valid single visit permit, Federal Duck Stamp or Golden...

50 CFR 25.57 - Exceptions and exemptions.

Code of Federal Regulations, 2012 CFR

2012-10-01

...) Persons accompanying the holder of a valid single visit permit, Federal Duck Stamp or Golden Eagle, Age..., children, or parents accompanying the holder of a valid single visit permit, Federal Duck Stamp or Golden...

30 CFR 14.1 - Purpose, effective date for approval holders.

Code of Federal Regulations, 2010 CFR

2010-07-01

... CONVEYOR BELTS General Provisions § 14.1 Purpose, effective date for approval holders. This Part establishes the flame resistance requirements for MSHA approval of conveyor belts for use in underground coal...

Apparatus for sectioning demountable semiconductor samples

DOEpatents

Sopori, B.L.; Wolf, A.

1984-01-01

Apparatus for use during polishing and sectioning operations of a ribbon sample is described. The sample holder includes a cylinder having an axially extending sample cavity terminated in a first funnel-shaped opening and a second slot-like opening. A spring-loaded pressure plunger is located adjacent the second opening of the sample cavity for frictional engagement of the sample cavity. A heat softenable molding medium is inserted in the funnel-shaped opening, to surround the sample. After polishing, the heater is energized to allow draining of the molding medium from the sample cavity. During manual polishing, the second end of the sample holder is inserted in a support ring which provides mechanical support as well as alignment of the sample holder during polishing. A gauge block for measuring the protrusion of a sample beyond the second wall of the holder is also disclosed.

Spot test kit for explosives detection

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pagoria, Philip F; Whipple, Richard E; Nunes, Peter J

An explosion tester system comprising a body, a lateral flow membrane swab unit adapted to be removeably connected to the body, a first explosives detecting reagent, a first reagent holder and dispenser operatively connected to the body, the first reagent holder and dispenser containing the first explosives detecting reagent and positioned to deliver the first explosives detecting reagent to the lateral flow membrane swab unit when the lateral flow membrane swab unit is connected to the body, a second explosives detecting reagent, and a second reagent holder and dispenser operatively connected to the body, the second reagent holder and dispensermore » containing the second explosives detecting reagent and positioned to deliver the second explosives detecting reagent to the lateral flow membrane swab unit when the lateral flow membrane swab unit is connected to the body.« less

Design selection of an innovative tool holder for ultrasonic vibration assisted turning (IN-UVAT) using finite element analysis simulation

NASA Astrophysics Data System (ADS)

Rachmat, Haris; Ibrahim, M. Rasidi; Hasan, Sulaiman bin

2017-04-01

On of high technology in machining is ultrasonic vibration assisted turning. The design of tool holder was a crucial step to make sure the tool holder is enough to handle all forces on turning process. Because of the direct experimental approach is expensive, the paper studied to predict feasibility of tool holder displacement and effective stress was used the computational in finite element simulation. SS201 and AISI 1045 materials were used with sharp and ramp corners flexure hinges on design. The result shows that AISI 1045 material and which has ramp corner flexure hinge was the best choice to be produced. The displacement is around 11.3 micron and effective stress is 1.71e+008 N/m2 and also the factor of safety is 3.10.

17 CFR 240.14c-3 - Annual report to be furnished security holders.

Code of Federal Regulations, 2010 CFR

2010-04-01

...) A registrant will be considered to have delivered a Notice of Internet Availability of Proxy... Notice of Internet Availability of Proxy Materials, annual report to security holders or information...

42 CFR 60.21 - Refunds.

Code of Federal Regulations, 2010 CFR

2010-10-01

... The Loan § 60.21 Refunds. (a) Student authorization. By applying for a HEAL loan, a student authorizes... original lender (or to a subsequent holder of the loan note, if the school has knowledge of the holder's...

Welding fixture for nuclear fuel pin cladding assemblies

DOEpatents

Oakley, David J.; Feld, Sam H.

1986-01-01

A welding fixture for locating a driver sleeve about the open end of a nuclear fuel pin cladding. The welding fixture includes a holder provided with an open cavity having shoulders for properly positioning the driver sleeve, the end cap, and a soft, high temperature resistant plastic protective sleeve that surrounds a portion of the end cap stem. Ejected contaminant particles spewed forth by closure of the cladding by pulsed magnetic welding techniques are captured within a contamination trap formed in the holder for ultimate removal and disposal of contaminating particles along with the holder.

Mining planer with pivotal tool holder

DOE Office of Scientific and Technical Information (OSTI.GOV)

Braun, E.; Braun, G.

1983-10-04

A planer assembly is disclosed for winning minerals from a mineral face comprising, a planer guide member, at least two planers slidably engaged on the guide member for movement in a travel direction along the face, a hinge interconnecting the two planers for transferring rotational moment applied to the planers and a planer tool holder mounted on each planer which carries a tool. The planer tool holder is positionable at an angle to make a cut of a selected depth with the depth increasing from planer to planer in a direction opposite the travel direction.

High-precision micro/nano-scale machining system

DOEpatents

Kapoor, Shiv G.; Bourne, Keith Allen; DeVor, Richard E.

2014-08-19

A high precision micro/nanoscale machining system. A multi-axis movement machine provides relative movement along multiple axes between a workpiece and a tool holder. A cutting tool is disposed on a flexible cantilever held by the tool holder, the tool holder being movable to provide at least two of the axes to set the angle and distance of the cutting tool relative to the workpiece. A feedback control system uses measurement of deflection of the cantilever during cutting to maintain a desired cantilever deflection and hence a desired load on the cutting tool.

A Reference-Free and Non-Contact Method for Detecting and Imaging Damage in Adhesive-Bonded Structures Using Air-Coupled Ultrasonic Transducers.

PubMed

Yonathan Sunarsa, Timotius; Aryan, Pouria; Jeon, Ikgeun; Park, Byeongjin; Liu, Peipei; Sohn, Hoon

2017-12-08

Adhesive bonded structures have been widely used in aerospace, automobile, and marine industries. Due to the complex nature of the failure mechanisms of bonded structures, cost-effective and reliable damage detection is crucial for these industries. Most of the common damage detection methods are not adequately sensitive to the presence of weakened bonding. This paper presents an experimental and analytical method for the in-situ detection of damage in adhesive-bonded structures. The method is fully non-contact, using air-coupled ultrasonic transducers (ACT) for ultrasonic wave generation and sensing. The uniqueness of the proposed method relies on accurate detection and localization of weakened bonding in complex adhesive bonded structures. The specimens tested in this study are parts of real-world structures with critical and complex damage types, provided by Hyundai Heavy Industries ® and IKTS Fraunhofer ® . Various transmitter and receiver configurations, including through transmission, pitch-catch scanning, and probe holder angles, were attempted, and the obtained results were analyzed. The method examines the time-of-flight of the ultrasonic waves over a target inspection area, and the spatial variation of the time-of-flight information was examined to visualize and locate damage. The proposed method works without relying on reference data obtained from the pristine condition of the target specimen. Aluminum bonded plates and triplex adhesive layers with debonding and weakened bonding were used to examine the effectiveness of the method.

A Reference-Free and Non-Contact Method for Detecting and Imaging Damage in Adhesive-Bonded Structures Using Air-Coupled Ultrasonic Transducers

PubMed Central

Yonathan Sunarsa, Timotius; Aryan, Pouria; Jeon, Ikgeun; Park, Byeongjin; Liu, Peipei

2017-01-01

Adhesive bonded structures have been widely used in aerospace, automobile, and marine industries. Due to the complex nature of the failure mechanisms of bonded structures, cost-effective and reliable damage detection is crucial for these industries. Most of the common damage detection methods are not adequately sensitive to the presence of weakened bonding. This paper presents an experimental and analytical method for the in-situ detection of damage in adhesive-bonded structures. The method is fully non-contact, using air-coupled ultrasonic transducers (ACT) for ultrasonic wave generation and sensing. The uniqueness of the proposed method relies on accurate detection and localization of weakened bonding in complex adhesive bonded structures. The specimens tested in this study are parts of real-world structures with critical and complex damage types, provided by Hyundai Heavy Industries® and IKTS Fraunhofer®. Various transmitter and receiver configurations, including through transmission, pitch-catch scanning, and probe holder angles, were attempted, and the obtained results were analyzed. The method examines the time-of-flight of the ultrasonic waves over a target inspection area, and the spatial variation of the time-of-flight information was examined to visualize and locate damage. The proposed method works without relying on reference data obtained from the pristine condition of the target specimen. Aluminum bonded plates and triplex adhesive layers with debonding and weakened bonding were used to examine the effectiveness of the method. PMID:29292752

Novel Concept of Attaching Endoscope Holder to Microscope for Two Handed Endoscopic Tympanoplasty.

PubMed

Khan, Mubarak M; Parab, Sapna R

2016-06-01

The well established techniques in tympanoplasty are routinely performed with operating microscopes for many decades now. Endoscopic ear surgeries provide minimally invasive approach to the middle ear and evolving new science in the field of otology. The disadvantage of endoscopic ear surgeries is that it is one-handed surgical technique as the non-dominant left hand of the surgeon is utilized for holding and manipulating the endoscope. This necessitated the need for development of the endoscope holder which would allow both hands of surgeon to be free for surgical manipulation and also allow alternate use of microscope during tympanoplasty. To report the preliminary utility of our designed and developed endoscope holder attachment gripping to microscope for two handed technique of endoscopic tympanoplasty. Prospective Non Randomized Clinical Study. Our endoscope holder attachment for microscope was designed and developed to aid in endoscopic ear surgery and to overcome the disadvantage of single handed endoscopic surgery. It was tested for endoscopic Tympanoplasty. The design of the endoscope holder attachment is described in detail along with its manipulation and manoeuvreing. A total of 78 endoholder assisted type 1 endoscopic cartilage tympanoplasties were operated to evaluate its feasibility for the two handed technique and to evaluate the results of endoscopic type 1 cartilage tympanoplasty. In early follow up period ranging from 6 to 20 months, the graft uptake was seen in 76 ears with one residual perforation and 1 recurrent perforations giving a success rate of 97.435 %. Our endocsope holder attachment for gripping microscope is a good option for two handed technique in endoscopic type 1 cartilage tympanoplasty. The study reports the successful application and use of our endoscope holder attachment for gripping microscope in two handed technique of endoscopic type 1 cartilage tympanoplasty and comparable results with microscopic techniques. IV.

49 CFR 383.25 - Commercial learner's permit (CLP).

Code of Federal Regulations, 2013 CFR

2013-10-01

...) necessary to operate the CMV. The CDL holder must at all times be physically present in the front seat of... CLP holder with a P endorsement is prohibited from operating a CMV carrying passengers, other than...

49 CFR 383.25 - Commercial learner's permit (CLP).

Code of Federal Regulations, 2012 CFR

2012-10-01

...) necessary to operate the CMV. The CDL holder must at all times be physically present in the front seat of... CLP holder with a P endorsement is prohibited from operating a CMV carrying passengers, other than...

49 CFR 383.25 - Commercial learner's permit (CLP).

Code of Federal Regulations, 2014 CFR

2014-10-01

...) necessary to operate the CMV. The CDL holder must at all times be physically present in the front seat of... CLP holder with a P endorsement is prohibited from operating a CMV carrying passengers, other than...

49 CFR 383.25 - Commercial learner's permit (CLP).

Code of Federal Regulations, 2011 CFR

2011-10-01

...) necessary to operate the CMV. The CDL holder must at all times be physically present in the front seat of... CLP holder with a P endorsement is prohibited from operating a CMV carrying passengers, other than...

32 CFR 1907.23 - Response by originator(s) and/or any interested party.

Code of Federal Regulations, 2010 CFR

2010-07-01

... INTELLIGENCE AGENCY CHALLENGES TO CLASSIFICATION OF DOCUMENTS BY AUTHORIZED HOLDERS PURSUANT TO § 1.9 OF... authorized holder as well as the business requirements of the originator including their responsibilities...

19 CFR 134.23 - Containers or holders designed for or capable of reuse.

Code of Federal Regulations, 2014 CFR

2014-04-01

... containers or holders are subject to the treatment specified in General Rule of Interpretation 5(b... cologne bottles reusable as flower vases, and other containers which have a lasting value or decorative...

19 CFR 134.23 - Containers or holders designed for or capable of reuse.

Code of Federal Regulations, 2013 CFR

2013-04-01

... containers or holders are subject to the treatment specified in General Rule of Interpretation 5(b... cologne bottles reusable as flower vases, and other containers which have a lasting value or decorative...

19 CFR 134.23 - Containers or holders designed for or capable of reuse.

Code of Federal Regulations, 2012 CFR

2012-04-01

... containers or holders are subject to the treatment specified in General Rule of Interpretation 5(b... cologne bottles reusable as flower vases, and other containers which have a lasting value or decorative...

19 CFR 134.23 - Containers or holders designed for or capable of reuse.

Code of Federal Regulations, 2010 CFR

2010-04-01

... containers or holders are subject to the treatment specified in General Rule of Interpretation 5(b... cologne bottles reusable as flower vases, and other containers which have a lasting value or decorative...

Apparatus for sectioning demountable semiconductor samples

DOEpatents

Sopori, Bhushan L.; Wolf, Abraham

1984-01-01

Apparatus for use during polishing and sectioning operations of a ribbon sample is described. The sample holder includes a cylinder having an axially extending sample cavity terminated in a first funnel-shaped opening and a second slot-like opening. A spring-loaded pressure plunger is located adjacent the second opening of the sample cavity for frictional engagement of the sample prior to introduction of a molding medium in the sample cavity. A heat softenable molding medium is inserted in the funnel-shaped opening, to surround the sample. After polishing, the heater is energized to allow draining of the molding medium from the sample cavity. During manual polishing, the second end of the sample holder is inserted in a support ring which provides mechanical support as well as alignment of the sample holder during polishing. A gauge block for measuring the protrusion of a sample beyond the second wall of the holder is also disclosed.

Investigation of holder pressure and size effects in micro deep drawing of rectangular work pieces driven by piezoelectric actuator.

PubMed

Aminzahed, Iman; Mashhadi, Mahmoud Mosavi; Sereshk, Mohammad Reza Vaziri

2017-02-01

Micro forming is a manufacturing process to fabricate micro parts with high quality and a cost effective manner. Deep drawing could be a favorable method for production of complicated parts in macro and micro sizes. In this paper piezoelectric actuator is used as a novel approach in the field of micro manufacturing. Also, in current work, investigations are conducted with four rectangular punches and blanks with various thicknesses. Blank holder pressure effects on thickness distributions, punch force, and springback are studied. According to the results of this work, increasing of blank holder pressure in scaled deep drawing, in contrast to thickness of drawn part, leads to decrease in the punch forces and springback. Furthermore, it is shown that in micro deep drawing, the effects of holder pressure on mentioned parameters can be ignored. Copyright © 2016 Elsevier B.V. All rights reserved.

Filters for blocking macroparticles in plasma deposition apparatus

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anders, Andre; Kolbeck, Jonathan

This disclosure provides systems, methods, and apparatus related to blocking macroparticles in deposition processes utilizing plasmas. In one aspect, an apparatus includes a cathode, a substrate holder, a first magnet, a second magnet, and a structure. The cathode is configured to generate a plasma. The substrate holder is configured to hold a substrate. The first magnet is disposed proximate a first side of the cathode. The second magnet is disposed proximate a second side of the substrate holder. A magnetic field exists between the first magnet and the second magnet and a flow of the plasma substantially follows the magneticmore » field. The structure is disposed between the second side of the cathode and the first side of the substrate holder and is positioned proximate a region where the magnetic field between the first magnet and the second magnet is weak.« less

Stability of Cortisol and Cortisone in Human Breast Milk During Holder Pasteurization.

PubMed

van der Voorn, Bibian; de Waard, Marita; Dijkstra, Lisette R; Heijboer, Annemieke C; Rotteveel, Joost; van Goudoever, Johannes B; Finken, Martijn J J

2017-12-01

Human donor milk is the feeding of choice for preterm infants, when own mother's milk is not available. Holder pasteurization is necessary to secure the safety of donor milk, although it can affect milk quality by reduction of nutritional and bioactive components. Recently, research has focused on the potential role of breast milk glucocorticoids for infant development. At this moment, it is unknown whether pasteurization affects milk glucocorticoid levels. Therefore, we assessed whether Holder pasteurization, the most frequently used method nowadays, reduces breast milk cortisol and cortisone levels, using breast milk samples from 30 women who delivered at term. We found tight correlations between pre- and postpasteurization levels of cortisol (R = 0.99) and cortisone (R = 0.98), and good agreement in Passing and Bablok regression analysis. In conclusion, cortisol and cortisone in human term breast milk are not significantly affected by Holder pasteurization.

Isolation of Resistance-Bearing Microorganisms

NASA Technical Reports Server (NTRS)

Venkateswaran, Kasthuri, J.; Probst, Alexander; Vaishampayan, Parang A.; Ghosh, Sudeshna; Osman, Shariff

2010-01-01

To better exploit the principles of gas transport and mass transport during the processes of cell seeding of 3D scaffolds and in vitro culture of 3D tissue engineered constructs, the oscillatory cell culture bioreactor provides a flow of cell suspensions and culture media directly through a porous 3D scaffold (during cell seeding) and a 3D construct (during subsequent cultivation) within a highly gas-permeable closed-loop tube. This design is simple, modular, and flexible, and its component parts are easy to assemble and operate, and are inexpensive. Chamber volume can be very low, but can be easily scaled up. This innovation is well suited to work with different biological specimens, particularly with cells having high oxygen requirements and/or shear sensitivity, and different scaffold structures and dimensions. The closed-loop changer is highly gas permeable to allow efficient gas exchange during the cell seeding/culturing process. A porous scaffold, which may be seeded with cells, is fixed by means of a scaffold holder to the chamber wall with scaffold/construct orientation with respect to the chamber determined by the geometry of the scaffold holder. A fluid, with/without biological specimens, is added to the chamber such that all, or most, of the air is displaced (i.e., with or without an enclosed air bubble). Motion is applied to the chamber within a controlled environment (e.g., oscillatory motion within a humidified 37 C incubator). Movement of the chamber induces relative motion of the scaffold/construct with respect to the fluid. In case the fluid is a cell suspension, cells will come into contact with the scaffold and eventually adhere to it. Alternatively, cells can be seeded on scaffolds by gel entrapment prior to bioreactor cultivation. Subsequently, the oscillatory cell culture bioreactor will provide efficient gas exchange (i.e., of oxygen and carbon dioxide, as required for viability of metabolically active cells) and controlled levels of fluid dynamic shear (i.e., as required for viability of shear-sensitive cells) to the developing engineered tissue construct. This bioreactor was recently utilized to show independent and interactive effects of a growth factor (IGF-I) and slow bidirectional perfusion on the survival, differentiation, and contractile performance of 3D tissue engineering cardiac constructs. The main application of this system is within the tissue engineering industry. The ideal final application is within the automated mass production of tissue- engineered constructs. Target industries could be both life sciences companies as well as bioreactor device producing companies.

Oscillating Cell Culture Bioreactor

NASA Technical Reports Server (NTRS)

Freed, Lisa E.; Cheng, Mingyu; Moretti, Matteo G.

2010-01-01

To better exploit the principles of gas transport and mass transport during the processes of cell seeding of 3D scaffolds and in vitro culture of 3D tissue engineered constructs, the oscillatory cell culture bioreactor provides a flow of cell suspensions and culture media directly through a porous 3D scaffold (during cell seeding) and a 3D construct (during subsequent cultivation) within a highly gas-permeable closed-loop tube. This design is simple, modular, and flexible, and its component parts are easy to assemble and operate, and are inexpensive. Chamber volume can be very low, but can be easily scaled up. This innovation is well suited to work with different biological specimens, particularly with cells having high oxygen requirements and/or shear sensitivity, and different scaffold structures and dimensions. The closed-loop changer is highly gas permeable to allow efficient gas exchange during the cell seeding/culturing process. A porous scaffold, which may be seeded with cells, is fixed by means of a scaffold holder to the chamber wall with scaffold/construct orientation with respect to the chamber determined by the geometry of the scaffold holder. A fluid, with/without biological specimens, is added to the chamber such that all, or most, of the air is displaced (i.e., with or without an enclosed air bubble). Motion is applied to the chamber within a controlled environment (e.g., oscillatory motion within a humidified 37 C incubator). Movement of the chamber induces relative motion of the scaffold/construct with respect to the fluid. In case the fluid is a cell suspension, cells will come into contact with the scaffold and eventually adhere to it. Alternatively, cells can be seeded on scaffolds by gel entrapment prior to bioreactor cultivation. Subsequently, the oscillatory cell culture bioreactor will provide efficient gas exchange (i.e., of oxygen and carbon dioxide, as required for viability of metabolically active cells) and controlled levels of fluid dynamic shear (i.e., as required for viability of shear-sensitive cells) to the developing engineered tissue construct. This bioreactor was recently utilized to show independent and interactive effects of a growth factor (IGF-I) and slow bidirectional perfusion on the survival, differentiation, and contractile performance of 3D tissue engineering cardiac constructs. The main application of this system is within the tissue engineering industry. The ideal final application is within the automated mass production of tissue- engineered constructs. Target industries could be both life sciences companies as well as bioreactor device producing companies.

Acceptance Testing of Thermoluminescent Dosimeter Holders.

PubMed

Romanyukha, Alexander; Grypp, Matthew D; Sharp, Thad J; DiRito, John N; Nelson, Martin E; Mavrogianis, Stanley T; Torres, Jeancarlo; Benevides, Luis A

2018-05-01

The U.S. Navy uses the Harshaw 8840/8841 dosimetric (DT-702/PD) system, which employs LiF:Mg,Cu,P thermoluminescent dosimeters (TLDs), developed and produced by Thermo Fisher Scientific (TFS). The dosimeter consists of four LiF:Mg,Cu,P elements, mounted in Teflon® on an aluminum card and placed in a plastic holder. The holder contains a unique filter for each chip made of copper, acrylonitrile butadiene styrene (ABS), Mylar®, and tin. For accredited dosimetry labs, the ISO/IEC 17025:2005(E) requires an acceptance procedure for all new equipment. The Naval Dosimetry Center (NDC) has developed and tested a new non-destructive procedure, which enables the verification and the evaluation of embedded filters in the holders. Testing is based on attenuation measurements of low-energy radiation transmitted through each filter in a representative sample group of holders to verify that the correct filter type and thickness are present. The measured response ratios are then compared with the expected response ratios. In addition, each element's measured response is compared to the mean response of the group. The test was designed and tested to identify significant nonconformities, such as missing copper or tin filters, double copper or double tin filters, or other nonconformities that may impact TLD response ratios. During the implementation of the developed procedure, testing revealed a holder with a double copper filter. To complete the evaluation, the impact of the nonconformities on proficiency testing was examined. The evaluation revealed failures in proficiency testing categories III and IV when these dosimeters were irradiated to high-energy betas.

Initial experience using a robotic-driven laparoscopic needle holder with ergonomic handle: assessment of surgeons' task performance and ergonomics.

PubMed

Sánchez-Margallo, Juan A; Sánchez-Margallo, Francisco M

2017-12-01

The objective of this study is to assess the surgeons' performance and ergonomics during the use of a robotic-driven needle holder in laparoscopic suturing tasks. Six right-handed laparoscopic surgeons with different levels of experience took part in this study. Participants performed a set of three different intracorporeal suturing tasks organized in ten trials during a period of five weeks. Surgeons used both conventional (Conv) and robotic (Rob) laparoscopic needle holders. Precision using the surgical needle, quality of the intracorporeal suturing performance, execution time and leakage pressure for the urethrovesical anastomosis, as well as the ergonomics of the surgeon's hand posture, were analyzed during the first, fifth and last trials. No statistically significant differences in precision and quality of suturing performance were obtained between both groups of instruments. Surgeons required more time using the robotic instrument than using the conventional needle holder to perform the urethrovesical anastomosis, but execution time was significantly reduced after training ([Formula: see text] 0.05). There were no differences in leakage pressure for the anastomoses carried out by both instruments. After training, novice surgeons significantly improved the ergonomics of the wrist ([Formula: see text] 0.05) and index finger (Conv: 36.381[Formula: see text], Rob: 30.389[Formula: see text]; p = 0.024) when using the robotic instrument compared to the conventional needle holder. Results have shown that, although both instruments offer similar technical performance, the robotic-driven instrument results in better ergonomics for the surgeon's hand posture compared to the use of a conventional laparoscopic needle holder in intracorporeal suturing.

51. (no plate) Lens, lens pedestal, mercury float, shade holder ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

51. (no plate) Lens, lens pedestal, mercury float, shade holder installation, drawing # 3101, sheet 2 of 2. Approved April 6, 1928. - Block Island Southeast Light, Spring Street & Mohegan Trail at Mohegan Bluffs, New Shoreham, Washington County, RI

10 CFR 95.31 - Protective personnel.

Code of Federal Regulations, 2010 CFR

2010-01-01

... equivalent) if the licensee, certificate holder, or other person possesses information classified... Information. (b) Possess a “Q” access authorization (or CSA equivalent) if the licensee, certificate holder... vulnerability information; and certain particularly sensitive Naval Nuclear Propulsion Program information (e.g...

10 CFR 95.31 - Protective personnel.

Code of Federal Regulations, 2011 CFR

2011-01-01

... equivalent) if the licensee, certificate holder, or other person possesses information classified... Information. (b) Possess a “Q” access authorization (or CSA equivalent) if the licensee, certificate holder... vulnerability information; and certain particularly sensitive Naval Nuclear Propulsion Program information (e.g...

77 FR 46539 - Self-Regulatory Organizations; NYSE Arca, Inc.; Notice of Filing and Immediate Effectiveness of...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-03

... Holder's compliance with these requirements through an exam-based review of the ETP Holder's internal...-77 on the subject line. Paper Comments Send paper comments in triplicate to Elizabeth M. Murphy...

75 FR 55622 - Self-Regulatory Organizations; NYSE Amex LLC; Notice of Filing and Immediate Effectiveness of...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-13

....3NY(d)(3). Under the proposed interpretation, after entering a Reserve Order, an ATP Holder may enter... provide ATP Holders with certainty with respect to the applicable exposure requirements for reserve orders...

42 CFR 60.54 - Payment of refunds by schools.

Code of Federal Regulations, 2014 CFR

2014-10-01

... subsequent holder of the loan note, if the school has knowledge of the holder's identity). At the same time... Management and Budget under control number 0915-0108) [48 FR 38988, Aug. 26, 1983, as amended at 57 FR 28799...

42 CFR 60.54 - Payment of refunds by schools.

Code of Federal Regulations, 2013 CFR

2013-10-01

... subsequent holder of the loan note, if the school has knowledge of the holder's identity). At the same time... Management and Budget under control number 0915-0108) [48 FR 38988, Aug. 26, 1983, as amended at 57 FR 28799...

42 CFR 60.54 - Payment of refunds by schools.

Code of Federal Regulations, 2012 CFR

2012-10-01

... subsequent holder of the loan note, if the school has knowledge of the holder's identity). At the same time... Management and Budget under control number 0915-0108) [48 FR 38988, Aug. 26, 1983, as amended at 57 FR 28799...

50 CFR 80.33 - How does an agency decide who to count as paid license holders in the annual certification?

Code of Federal Regulations, 2013 CFR

2013-10-01

... AND SPORT FISH RESTORATION PROGRAM ADMINISTRATIVE REQUIREMENTS, PITTMAN-ROBERTSON WILDLIFE RESTORATION AND DINGELL-JOHNSON SPORT FISH RESTORATION ACTS Certification of License Holders § 80.33 How does an...

32 CFR 2001.14 - Classification challenges.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 32 National Defense 6 2013-07-01 2013-07-01 false Classification challenges. 2001.14 Section 2001... Classification § 2001.14 Classification challenges. (a) Challenging classification. Authorized holders, including authorized holders outside the classifying agency, who want to challenge the classification status of...

32 CFR 2001.14 - Classification challenges.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 32 National Defense 6 2014-07-01 2014-07-01 false Classification challenges. 2001.14 Section 2001... Classification § 2001.14 Classification challenges. (a) Challenging classification. Authorized holders, including authorized holders outside the classifying agency, who want to challenge the classification status of...

32 CFR 2001.14 - Classification challenges.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 32 National Defense 6 2012-07-01 2012-07-01 false Classification challenges. 2001.14 Section 2001... Classification § 2001.14 Classification challenges. (a) Challenging classification. Authorized holders, including authorized holders outside the classifying agency, who want to challenge the classification status of...

32 CFR 2001.14 - Classification challenges.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 32 National Defense 6 2011-07-01 2011-07-01 false Classification challenges. 2001.14 Section 2001... Classification § 2001.14 Classification challenges. (a) Challenging classification. Authorized holders, including authorized holders outside the classifying agency, who want to challenge the classification status of...

42 CFR 60.54 - Payment of refunds by schools.

Code of Federal Regulations, 2010 CFR

2010-10-01

... subsequent holder of the loan note, if the school has knowledge of the holder's identity). At the same time... Management and Budget under control number 0915-0108) [48 FR 38988, Aug. 26, 1983, as amended at 57 FR 28799...

RESTRAINING SYSTEM FOR PLETHYSMOGRAPHY IN SMALL ANIMALS

EPA Science Inventory

A restraining technique for immobilizing awake guinea pigs and rats during physiological measurements is described. The basic device consists of an adjustable acrylic holder that supports the animal in a standing position while restricting movement of the four legs. The holder al...

Modeling of the minimum variable blank holder force based on forming limit diagram (FLD) in deep drawing process

NASA Astrophysics Data System (ADS)

Candra, S.; Batan, I. M. L.; Berata, W.; Pramono, A. S.

2017-11-01

This paper presents the mathematical approach of minimum blank holder force to prevent wrinkling in deep drawing process of the cylindrical cup. Based on the maximum of minor-major strain ratio, the slab method was applied to determine the modeling of minimum variable blank holder force (VBHF) and it compared to FE simulation. The Tin steel sheet of T4-CA grade, with the thickness of 0.2 mm was used in this study. The modeling of minimum VBHF can be used as a simple reference to prevent wrinkling in deep drawing.

Welding fixture for nuclear fuel pin cladding assemblies

DOEpatents

Oakley, D.J.; Feld, S.H.

1984-02-22

A welding fixture is described for locating a driver sleeve about the open end of a nuclear fuel pin cladding. The welding fixture includes a holder provided with an open cavity having shoulders for properly positioning the driver sleeve, the end cap, and a soft, high temperature resistant plastic protective sleeve that surrounds a portion of the end cap stem. Ejected contaminant particles spewed forth by closure of the cladding by pulsed magnetic welding techniques are captured within a contamination trap formed in the holder for ultimate removal and disposal of contaminating particles along with the holder.

75 FR 44804 - Privacy Act of 1974; Notice of a New Privacy Act System of Records (SORN), Ginnie Mae Mortgage...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-29

...The Department proposes to establish a new Privacy Act SORN subject to the Privacy Act of 1974 (5 U.S.C. 552a), as amended, entitled Ginnie Mae Mortgage-Backed Security Unclaimed Funds System. The new record system will be used to track unclaimed security holder payments. Such unclaimed payments are owed to certificate holders of Ginnie Mae-guaranteed mortgage-backed securities who cannot be located by the Ginnie Mae servicer. Ginnie Mae tracks this information to ensure that security holders are paid properly.

Holder and Topic Based Analysis of Emotions on Blog Texts: A Case Study for Bengali

NASA Astrophysics Data System (ADS)

Das, Dipankar; Bandyopadhyay, Sivaji

The paper presents an extended approach of analyzing emotions of the blog users on different topics. The rule based techniques to identify emotion holders and topics with respect to their corresponding emotional expressions helps to develop the baseline system. On the other hand, the Support Vector Machine (SVM) based supervised framework identifies the holders, topics and emotional expressions from the blog sentences by outperforming the baseline system. The existence of many to many relations between the holders and the topics with respect to Ekman's six different emotion classes has been examined using two way evaluation techniques, one is with respect to holder and other is from the perspective of topic. The results of the system were found satisfactory in comparison with the agreement of the subjective annotation. The error analysis shows that the topic of a blog at document level is not always conveyed at the sentence level. Moreover, the difficulty in identifying topic from a blog document is due to the problem of identifying some features like bigrams, Named Entities and sentiment. Thus, we employed a semantic clustering approach along with these features to identify the similarity between document level topic and sentential topic as well as to improve the results of identifying the document level topic.

CFD analysis of a scramjet combustor with cavity based flame holders

NASA Astrophysics Data System (ADS)

Kummitha, Obula Reddy; Pandey, Krishna Murari; Gupta, Rajat

2018-03-01

Numerical analysis of a scramjet combustor with different cavity flame holders has been carried out using ANSYS 16 - FLUENT tool. In this research article the internal fluid flow behaviour of the scramjet combustor with different cavity based flame holders have been discussed in detail. Two dimensional Reynolds-Averaged Navier-Stokes governing(RANS) equations and shear stress turbulence (SST) k - ω model along with finite rate/eddy dissipation chemistry turbulence have been considered for modelling chemical reacting flows. Due to the advantage of less computational time, global one step reaction mechanism has been used for combustion modelling of hydrogen and air. The performance of the scramjet combustor with two different cavities namely spherical and step cavity has been compared with the standard DLR scramjet. From the comparison of numerical results, it is found that the development of recirculation regions and additional shock waves from the edge of cavity flame holder is increased. And also it is observed that with the cavity flame holder the residence time of air in the scramjet combustor is also increased and achieved stabilized combustion. From this research analysis, it has been found that the mixing and combustion efficiency of scramjet combustor with step cavity design is optimum as compared to other models.

The Effect of Simulated Flash-Heat Pasteurization on Immune Components of Human Milk.

PubMed

Daniels, Brodie; Schmidt, Stefan; King, Tracy; Israel-Ballard, Kiersten; Amundson Mansen, Kimberly; Coutsoudis, Anna

2017-02-22

A pasteurization temperature monitoring system has been designed using FoneAstra, a cellphone-based networked sensing system, to monitor simulated flash-heat (FH) pasteurization. This study compared the effect of the FoneAstra FH (F-FH) method with the Sterifeed Holder method currently used by human milk banks on human milk immune components (immunoglobulin A (IgA), lactoferrin activity, lysozyme activity, interleukin (IL)-8 and IL-10). Donor milk samples ( N = 50) were obtained from a human milk bank, and pasteurized. Concentrations of IgA, IL-8, IL-10, lysozyme activity and lactoferrin activity were compared to their controls using the Student's t -test. Both methods demonstrated no destruction of interleukins. While the Holder method retained all lysozyme activity, the F-FH method only retained 78.4% activity ( p < 0.0001), and both methods showed a decrease in lactoferrin activity (71.1% Holder vs. 38.6% F-FH; p < 0.0001) and a decrease in the retention of total IgA (78.9% Holder vs. 25.2% F-FH; p < 0.0001). Despite increased destruction of immune components compared to Holder pasteurization, the benefits of F-FH in terms of its low cost, feasibility, safety and retention of immune components make it a valuable resource in low-income countries for pasteurizing human milk, potentially saving infants' lives.

High-Performance X-ray Detection in a New Analytical Electron Microscope

NASA Technical Reports Server (NTRS)

Lyman, C. E.; Goldstein, J. I.; Williams, D. B.; Ackland, D. W.; vonHarrach, S.; Nicholls, A. W.; Statham, P. J.

1994-01-01

X-ray detection by energy-dispersive spectrometry in the analytical electron microscope (AEM) is often limited by low collected X-ray intensity (P), modest peak-to-background (P/B) ratios, and limitations on total counting time (tau) due to specimen drift and contamination. A new AFM has been designed with maximization of P. P/B, and tau as the primary considerations. Maximization of P has been accomplished by employing a field-emission electron gun, X-ray detectors with high collection angles, high-speed beam blanking to allow only one photon into the detector at a time, and simultaneous collection from two detectors. P/B has been maximized by reducing extraneous background signals generated at the specimen holder, the polepieces and the detector collimator. The maximum practical tau has been increased by reducing specimen contamination and employing electronic drift correction. Performance improvments have been measured using the NIST standard Cr thin film. The 0-3 steradian solid angle of X-ray collection is the highest value available. The beam blanking scheme for X-ray detection provides 3-4 times greater throughput of X-rays at high count rates into a recorded spectrum than normal systems employing pulse-pileup rejection circuits. Simultaneous X-ray collection from two detectors allows the highest X-ray intensity yet recorded to be collected from the NIST Cr thin film. The measured P/B of 6300 is the highest level recorded for an AEM. In addition to collected X-ray intensity (cps/nA) and P/B measured on the standard Cr film, the product of these can be used as a figure-of-merit to evaluate instruments. Estimated minimum mass fraction (MMF) for Cr measured on the standard NIST Cr thin film is also proposed as a figure-of-merit for comparing X-ray detection in AEMs. Determinations here of the MMF of Cr detectable show at least a threefold improvement over previous instruments.

Characterization of Ti6Al7Nb alloy foams surface treated in aqueous NaOH and CaCl2 solutions.

PubMed

Bütev, Ezgi; Esen, Ziya; Bor, Şakir

2016-07-01

Ti6Al7Nb alloy foams having 53-73% porosity were manufactured via evaporation of magnesium space holders. A bioactive 1µm thick sodium hydrogel titanate layer, NaxH2-xTiyO2y+1, formed after 5M NaOH treatment, was converted to crystalline sodium titanate, Na2TiyO2y+1, as a result of post-heat treatment. On the other hand, subsequent CaCl2 treatment of NaOH treated specimens induced calcium titanate formation. However, heat treatment of NaOH-CaCl2 treated specimens led to the loss of calcium and disappearance of the titanate phase. All of the aforementioned surface treatments reduced yield strengths due to the oxidation of the cell walls of the foams, while elastic moduli remained mostly unchanged. Accordingly, equiaxed dimples seen on the fracture surfaces of as-manufactured foams turned into relatively flat and featureless fracture surfaces after surface treatments. On the other hand, Ca- and Na-rich coating preserved their mechanical stabilities and did not spall during fracture. The relation between mechanical properties of foams and macro-porosity fraction were found to obey a power law. The foams with 63 and 73% porosity met the desired biocompatibility requirements with fully open pore structures and elastic moduli similar to that of bone. In vitro tests conducted in simulated body fluid (SBF) showed that NaOH-heat treated surfaces exhibit the highest bioactivity and allow the formation of Ca-P rich phases having Ca/P ratio of 1.3 to form within 5 days. Although Ca-P rich phases formed only after 15 days on NaOH-CaCl2 treated specimens, the Ca/P ratio was closer to that of apatite found in bone. Copyright © 2016 Elsevier Ltd. All rights reserved.

Multisurface fixture permits easy grinding of tool bit angles

NASA Technical Reports Server (NTRS)

Jones, C. R.

1966-01-01

Multisurface fixture with a tool holder permits accurate grinding and finishing of right and left hand single point threading tools. All angles are ground by changing the fixture position to rest at various references angles without removing the tool from the holder.

46 CFR 5.201 - Voluntary deposits in event of mental or physical incompetence.

Code of Federal Regulations, 2013 CFR

2013-10-01

... incompetence of a holder of a credential or endorsement is caused by use of or addiction to dangerous drugs, a... mental or physical incompetence of a holder of a credential or endorsement is caused by use or addiction...

46 CFR 5.201 - Voluntary deposits in event of mental or physical incompetence.

Code of Federal Regulations, 2014 CFR

2014-10-01

... incompetence of a holder of a credential or endorsement is caused by use of or addiction to dangerous drugs, a... mental or physical incompetence of a holder of a credential or endorsement is caused by use or addiction...

46 CFR 5.201 - Voluntary deposits in event of mental or physical incompetence.

Code of Federal Regulations, 2010 CFR

2010-10-01

... incompetence of a holder of a credential or endorsement is caused by use of or addiction to dangerous drugs, a... mental or physical incompetence of a holder of a credential or endorsement is caused by use or addiction...

46 CFR 5.201 - Voluntary deposits in event of mental or physical incompetence.

Code of Federal Regulations, 2011 CFR

2011-10-01

... incompetence of a holder of a credential or endorsement is caused by use of or addiction to dangerous drugs, a... mental or physical incompetence of a holder of a credential or endorsement is caused by use or addiction...

46 CFR 5.201 - Voluntary deposits in event of mental or physical incompetence.

Code of Federal Regulations, 2012 CFR

2012-10-01

... incompetence of a holder of a credential or endorsement is caused by use of or addiction to dangerous drugs, a... mental or physical incompetence of a holder of a credential or endorsement is caused by use or addiction...

Balanced mechanical resonator for powder handling device

NASA Technical Reports Server (NTRS)

Sarrazin, Philippe C. (Inventor); Brunner, Will M. (Inventor)

2012-01-01

A system incorporating a balanced mechanical resonator and a method for vibration of a sample composed of granular material to generate motion of a powder sample inside the sample holder for obtaining improved analysis statistics, without imparting vibration to the sample holder support.

10 CFR 75.21 - General requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Accounting and Control for Facilities § 75.21 General requirements. (a) Each licensee or certificate holder... Safeguards Agreement shall establish, maintain, and follow written material accounting and control procedures. The licensee or certificate holder shall retain as a record current material accounting and control...

47 CFR 76.1000 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-10-01

... CABLE TELEVISION SERVICE Competitive Access to Cable Programming § 76.1000 Definitions. As used in this..., satellite cable programming vendors, satellite broadcast programming vendors, or terrestrial cable programming vendors will be attributed to their holders and may subject the interest holders to the rules of...

47 CFR 76.1000 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-10-01

... CABLE TELEVISION SERVICE Competitive Access to Cable Programming § 76.1000 Definitions. As used in this..., satellite cable programming vendors, satellite broadcast programming vendors, or terrestrial cable programming vendors will be attributed to their holders and may subject the interest holders to the rules of...

47 CFR 76.1000 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-10-01

... CABLE TELEVISION SERVICE Competitive Access to Cable Programming § 76.1000 Definitions. As used in this..., satellite cable programming vendors, satellite broadcast programming vendors, or terrestrial cable programming vendors will be attributed to their holders and may subject the interest holders to the rules of...

7 CFR 1463.103 - Eligible quota holder.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false Eligible quota holder. 1463.103 Section 1463.103 Agriculture Regulations of the Department of Agriculture (Continued) COMMODITY CREDIT CORPORATION, DEPARTMENT OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS 2005-2014 TOBACCO TRANSITION PROGRAM Tobacco...

15. VIEW OF DUMMY FUEL ELEMENT ON FUEL ELEMENT HOLDER. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

15. VIEW OF DUMMY FUEL ELEMENT ON FUEL ELEMENT HOLDER. SHOWS AIR FORCE MAN AT EDGE OF TANK. INEL PHOTO NUMBER 65-6176, TAKEN NOVEMBER 10, 1965. - Idaho National Engineering Laboratory, Advanced Reentry Vehicle Fusing System, Scoville, Butte County, ID

14 CFR 121.7 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... those that apply to aircraft rescue and firefighting service, or (2) A military airport that is active and operational. ETOPS Alternate Airport means an adequate airport listed in the certificate holder's... completed the certificate holder's ETOPS training program. Maximum Diversion Time means, for the purposes of...

14 CFR 121.7 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... those that apply to aircraft rescue and firefighting service, or (2) A military airport that is active and operational. ETOPS Alternate Airport means an adequate airport listed in the certificate holder's... completed the certificate holder's ETOPS training program. Maximum Diversion Time means, for the purposes of...

14 CFR 121.7 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... those that apply to aircraft rescue and firefighting service, or (2) A military airport that is active and operational. ETOPS Alternate Airport means an adequate airport listed in the certificate holder's... completed the certificate holder's ETOPS training program. Maximum Diversion Time means, for the purposes of...

14 CFR 121.7 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... those that apply to aircraft rescue and firefighting service, or (2) A military airport that is active and operational. ETOPS Alternate Airport means an adequate airport listed in the certificate holder's... completed the certificate holder's ETOPS training program. Maximum Diversion Time means, for the purposes of...

14 CFR 121.7 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... those that apply to aircraft rescue and firefighting service, or (2) A military airport that is active and operational. ETOPS Alternate Airport means an adequate airport listed in the certificate holder's... completed the certificate holder's ETOPS training program. Maximum Diversion Time means, for the purposes of...

47 CFR 76.1000 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... CABLE TELEVISION SERVICE Competitive Access to Cable Programming § 76.1000 Definitions. As used in this..., satellite cable programming vendors, satellite broadcast programming vendors, or terrestrial cable programming vendors will be attributed to their holders and may subject the interest holders to the rules of...

47 CFR 76.1000 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-10-01

... CABLE TELEVISION SERVICE Competitive Access to Cable Programming § 76.1000 Definitions. As used in this..., satellite cable programming vendors, satellite broadcast programming vendors, or terrestrial cable programming vendors will be attributed to their holders and may subject the interest holders to the rules of...

Small-scale thermal studies of volatile homemade explosives

DOE PAGES

Sandstrom, Mary M.; Brown, Geoffrey W.; Warner, Kirsten F.; ...

2016-01-26

Several homemade or improvised explosive mixtures that either contained volatile components or produced volatile products were examined using standard small-scale safety and thermal (SSST) testing that employed differential scanning calorimetry (DSC) techniques (constant heating rate and standard sample holders). KClO 3 and KClO 4 mixtures with dodecane exhibited different enthalpy behavior when using a vented sample holder in contrast to a sealed sample holder. The standard configuration produced profiles that exhibited only endothermic transitions. The sealed system produced profiles that exhibited additional exothermic transitions absent in the standard configuration produced profiles. When H 2O 2/fuel mixtures were examined, the volatilizationmore » of the peroxide (endothermic) dominated the profiles. When a sealed sample holder was used, the energetic releases of the mixture could be clearly observed. For AN and AN mixtures, the high temperature decomposition appears as an intense endothermic event. Using a nominally sealed sample holder also did not adequately contain the system. Only when a high-pressure rated sample holder was used the high temperature decomposition of the AN could be detected as an exothermic release. The testing was conducted during a proficiency (or round-robin type) test that included three U.S. Department of Energy and two U.S. Department of Defense laboratories. In the course of this proficiency test, certain HMEs exhibited thermal behavior that was not adequately accounted for by standard techniques. Further examination of this atypical behavior highlighted issues that may have not been recognized previously because some of these materials are not routinely tested. More importantly, if not recognized, the SSST testing results could lead to inaccurate safety assessments. Furthermore, this study provides examples, where standard techniques can be applied, and results can be obtained, but these results may be misleading in establishing thermal properties.« less

Skin temperature changes induced by strong static magnetic field exposure.

PubMed

Ichioka, Shigeru; Minegishi, Masayuki; Iwasaka, Masakazu; Shibata, Masahiro; Nakatsuka, Takashi; Ando, Joji; Ueno, Shoogo

2003-09-01

High intensity static magnetic fields, when applied to the whole body of the anesthetized rat, have previously been reported to decrease skin temperature. The hypothesis of the present study was that in diamagnetic water, molecules in the air play significant roles in the mechanism of skin temperature decrease. We used a horizontal cylindrical superconducting magnet. The magnet produced 8 T at its center. A thermistor probe was inserted in a subcutaneous pocket of the anesthetized rats to measure skin temperature. Animals (n=10) were placed in an open plastic holder in which the ambient air was free to move in any direction (group I). Animals (n=10) were placed in a closed holder in which the air circulation toward the direction of weak magnetic field was restricted (group II). Each holder was connected to a hydrometer to measure humidity around the animal in the holder. The data acquisition phase consisted of a 5 min baseline interval, followed by inserting the animal together with the holder into the center of the magnet bore for a 5 min exposure and a 5 min postexposure period outside the bore. In group I, skin temperature and humidity around the animal significantly decreased during exposure, followed by recovery after exposure. In group II, skin temperature and humidity did not decrease during the measurement. The skin temperature decrease was closely related to the decrease in humidity around the body of the animal in the holder, and the changes were completely blocked by restricting the air circulation in the direction of the bore entrance. Possible mechanisms responsible for the decrease in skin temperature may be associated with magnetically induced movement of water vapor at the skin surface, leading to skin temperature decrease. Copyright 2003 Wiley-Liss, Inc.

A simple cryogenic holder for tensile testing of soft biological tissues.

PubMed

Lepetit, J; Favier, R; Grajales, A; Skjervold, P O

2004-04-01

To overcome the difficulty of gripping soft biological materials for tensile test, a simple inexpensive cryogenic holder was developed which allows rapid (3 min) preparation of samples. It is made of 6 parts, built in a bakelite cloth, which is an excellent thermal isolant, and is used with rectangular (8x10(-2)x10(-2)x10(-2)m) samples. The holder with the sample inside is completely immersed in liquid nitrogen for 50 s. This duration allows the freezing of the sample ends on a 10(-2)m length and gives a very flat freezing surface throughout the sample cross section. The 6x10(-2)m central part of the sample remained at ambient temperature. Two parts of the holder help maintain the sample until its ends are vertically gripped in the tensile machine thus avoiding any sample deformation during this step. No pressure was applied on the frozen part of the sample by grips of the tensile machine and this avoids breaks in this region. The sample is fixed by adhesion forces (>1 kN) between its frozen parts and 2 pieces of the holder. The procedure has been successfully tested with bovine and salmon muscle samples and results show tensile breaks randomly distributed in the unfrozen region of the samples. Particular attention has been paid to obtain a very flat freezing surface so that the axial strain is equal throughout the sample and therefore any strain-related mechanical parameters can be accurately determined. The dimensions of the holder can be easily modified to fit other sample geometries and can be used with other biological materials.

76 FR 42130 - Agency Information Collection Activities: BioWatch Filter Holder Log

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-18

... DEPARTMENT OF HOMELAND SECURITY Agency Information Collection Activities: BioWatch Filter Holder...) assigned responsibility for installing and removing filters from aerosol collection devices and transportation to local laboratories for sample analysis. A standard filter log form is completed for each sample...

30 CFR 778.13 - Providing property interest information.

Code of Federal Regulations, 2010 CFR

2010-07-01

... INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS PERMIT APPLICATIONS-MINIMUM REQUIREMENTS FOR LEGAL, FINANCIAL, COMPLIANCE, AND RELATED...) Each legal or equitable owner(s) of record of the surface and mineral. (2) The holder(s) of record of...

76 FR 24504 - Agency Information Collection Activities: BioWatch Filter Holder Log

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-02

... DEPARTMENT OF HOMELAND SECURITY Agency Information Collection Activities: BioWatch Filter Holder...) assigned responsibility for installing and removing filters from aerosol collection devices and transportation to local laboratories for sample analysis. A standard filter log form is completed for each sample...

Sample Holder for Cryogenic Adhesive Shear Test

NASA Technical Reports Server (NTRS)

Ledbetter, F. E.; Clemons, J. M.; White, W. T.; Penn, B.; Semmel, M. L.

1983-01-01

Five samples tested in one cooldown. Holder mounted in testing machine. Submerged in cryogenic liquid held in cryostat. Movable crosshead of testing machine moves gradually downward. Samples placed under tension, one after another, starting with top one; each sample fails in turn before next is stressed.

14 CFR 26.5 - Applicability table.

Code of Federal Regulations, 2010 CFR

2010-01-01

... rule December 10, 2007 December 26, 2008 January 11, 2008 Existing 1 TC Holders 26.11 26.33 26.43, 26.45, 26.49 Pending 1 TC Applicants 26.11 26.37 26.43, 26.45 Existing 1 STC Holders N/A 26.35 26.47, 26...

Explosives tester

DOEpatents

Haas, Jeffrey S [San Ramon, CA; Howard, Douglas E [Livermore, CA; Eckels, Joel D [Livermore, CA; Nunes, Peter J [Danville, CA

2011-01-11

An explosives tester that can be used anywhere as a screening tool by non-technical personnel to determine whether a surface contains explosives. First and second explosives detecting reagent holders and dispensers are provided. A heater is provided for receiving the first and second explosives detecting reagent holders and dispensers.

NOTE: Monte Carlo simulation of correction factors for IAEA TLD holders

NASA Astrophysics Data System (ADS)

Hultqvist, Martha; Fernández-Varea, José M.; Izewska, Joanna

2010-03-01

The IAEA standard thermoluminescent dosimeter (TLD) holder has been developed for the IAEA/WHO TLD postal dose program for audits of high-energy photon beams, and it is also employed by the ESTRO-QUALity assurance network (EQUAL) and several national TLD audit networks. Factors correcting for the influence of the holder on the TL signal under reference conditions have been calculated in the present work from Monte Carlo simulations with the PENELOPE code for 60Co γ-rays and 4, 6, 10, 15, 18 and 25 MV photon beams. The simulation results are around 0.2% smaller than measured factors reported in the literature, but well within the combined standard uncertainties. The present study supports the use of the experimentally obtained holder correction factors in the determination of the absorbed dose to water from the TL readings; the factors calculated by means of Monte Carlo simulations may be adopted for the cases where there are no measured data.

An analysis of the attitudes of dental patients attending general dental practice in Galway.

PubMed

Hayes, Martina; Burke, Francis; McKenna, Gerald; Madden, Jamie; Cronin, Michael

2013-01-01

To describe the patterns of dental attendance and attitudes towards tooth loss of general dental practice patients in Galway. 1. To determine the pattern of adult dental attendance in general practices in Galway; and, 2. To examine the oral health attitudes of these patients. Questionnaires were distributed to 311 consecutive adult patients in the waiting rooms of ten general dental practices in Galway, which were randomly selected from the telephone directory. A total of 254 of the 311 questionnaires distributed were fully completed, returned and included in the results, giving a response rate of 81.7%. A total of 59% of dentate participants attended their dentist for annual or biannual examinations compared to 23% of edentate patients. Some 10.5% of medical card holders and 0.5% of non-medical card holders were edentulous. The data from the survey indicated that medical card holders in Galway were more likely to be edentulous than nonmedical card holders. Edentate patients were less likely to be regular dental attenders than dentate patients.

Promoted-Combustion Chamber with Induction Heating Coil

NASA Technical Reports Server (NTRS)

Richardson, Erin; Hagood, Richard; Lowery, Freida; Herald, Stephen

2006-01-01

An improved promoted-combustion system has been developed for studying the effects of elevated temperatures on the flammability of metals in pure oxygen. In prior promoted-combustion chambers, initial temperatures of metal specimens in experiments have been limited to the temperatures of gas supplies, usually near room temperature. Although limited elevated temperature promoted-combustion chambers have been developed using water-cooled induction coils for preheating specimens, these designs have been limited to low-pressure operation due to the hollow induction coil. In contrast, the improved promoted-combustion chamber can sustain a pressure up to 10 kpsi (69 MPa) and, through utilization of a solid induction coil, is capable of preheating a metal specimen up to its melting point [potentially in excess of 2,000 F (approximately equal to 1,100 C)]. Hence, the improved promoted combustion chamber makes a greater range of physical conditions and material properties accessible for experimentation. The chamber consists of a vertical cylindrical housing with an inner diameter of 8 in. (20.32 cm) and an inner height of 20.4 in. (51.81 cm). A threaded, sealing cover at one end of the housing can be unscrewed to gain access for installing a specimen. Inlet and outlet ports for gases are provided. Six openings arranged in a helical pattern in the chamber wall contain sealed sapphire windows for viewing an experiment in progress. The base of the chamber contains pressure-sealed electrical connectors for supplying power to the induction coil. The connectors feature a unique design that prevents induction heating of the housing and the pressure sealing surfaces; this is important because if such spurious induction heating were allowed to occur, chamber pressure could be lost. The induction coil is 10 in. (25.4 cm) long and is fitted with a specimen holder at its upper end. At its lower end, the induction coil is mounted on a ceramic base, which affords thermal insulation to prevent heating of the base of the chamber during use. A sapphire cylinder protects the coil against slag generated during an experiment. The induction coil is energized by a 6-kW water-cooled power supply operating at a frequency of 400 kHz. The induction coil is part of a parallel-tuned circuit, the tuning of which is used to adjust the coupling of power to the specimen. The chamber is mounted on a test stand along with pumps, valves, and plumbing for transferring pressurized gas into and out of the chamber. In addition to multiple video cameras aimed through the windows encircling the chamber, the chamber is instrumented with gauges for monitoring the progress of an experiment. One of the gauges is a dual-frequency infrared temperature transducer aimed at the specimen through one window. Chamber operation is achieved via a console that contains a computer running apparatus-specific software, a video recorder, and real-time video monitors. For safety, a blast wall separates the console from the test stand.

Immigrants in the one percent: The national origin of top wealth owners

PubMed Central

Keister, Lisa A.; Aronson, Brian

2017-01-01

Background Economic inequality in the United States is extreme, but little is known about the national origin of affluent households. Households in the top one percent by total wealth own vastly disproportionate quantities of household assets and have correspondingly high levels of economic, social, and political influence. The overrepresentation of white natives (i.e., those born in the U.S.) among high-wealth households is well-documented, but changing migration dynamics suggest that a growing portion of top households may be immigrants. Methods Because no single survey dataset contains top wealth holders and data about country of origin, this paper uses two publicly-available data sets: the Survey of Consumer Finances (SCF) and the Survey of Income and Program Participation (SIPP). Multiple imputation is used to impute country of birth from the SIPP into the SCF. Descriptive statistics are used to demonstrate reliability of the method, to estimate the prevalence of immigrants among top wealth holders, and to document patterns of asset ownership among affluent immigrants. Results Significant numbers of top wealth holders who are usually classified as white natives may be immigrants. Many top wealth holders appear to be European and Canadian immigrants, and increasing numbers of top wealth holders are likely from Asia and Latin America as well. Results suggest that of those in the top one percent of wealth holders, approximately 3% are European and Canadian immigrants, .5% are from Mexico or Cuban, and 1.7% are from Asia (especially Hong Kong, Taiwan, Mainland China, and India). Ownership of key assets varies considerably across affluent immigrant groups. Conclusion Although the percentage of top wealth holders who are immigrants is relatively small, these percentages represent large numbers of households with considerable resources and corresponding social and political influence. Evidence that the propensity to allocate wealth to real and financial assets varies across immigrant groups suggests that wealth ownership is more global than previous research suggests and that immigrant groups are likely to become more prevalent in top wealth positions in the U.S. As the representation of immigrants in top wealth positions grows, their economic, social, and political influence is likely to increase as well. PMID:28231335

Immigrants in the one percent: The national origin of top wealth owners.

PubMed

Keister, Lisa A; Aronson, Brian

2017-01-01

Economic inequality in the United States is extreme, but little is known about the national origin of affluent households. Households in the top one percent by total wealth own vastly disproportionate quantities of household assets and have correspondingly high levels of economic, social, and political influence. The overrepresentation of white natives (i.e., those born in the U.S.) among high-wealth households is well-documented, but changing migration dynamics suggest that a growing portion of top households may be immigrants. Because no single survey dataset contains top wealth holders and data about country of origin, this paper uses two publicly-available data sets: the Survey of Consumer Finances (SCF) and the Survey of Income and Program Participation (SIPP). Multiple imputation is used to impute country of birth from the SIPP into the SCF. Descriptive statistics are used to demonstrate reliability of the method, to estimate the prevalence of immigrants among top wealth holders, and to document patterns of asset ownership among affluent immigrants. Significant numbers of top wealth holders who are usually classified as white natives may be immigrants. Many top wealth holders appear to be European and Canadian immigrants, and increasing numbers of top wealth holders are likely from Asia and Latin America as well. Results suggest that of those in the top one percent of wealth holders, approximately 3% are European and Canadian immigrants, .5% are from Mexico or Cuban, and 1.7% are from Asia (especially Hong Kong, Taiwan, Mainland China, and India). Ownership of key assets varies considerably across affluent immigrant groups. Although the percentage of top wealth holders who are immigrants is relatively small, these percentages represent large numbers of households with considerable resources and corresponding social and political influence. Evidence that the propensity to allocate wealth to real and financial assets varies across immigrant groups suggests that wealth ownership is more global than previous research suggests and that immigrant groups are likely to become more prevalent in top wealth positions in the U.S. As the representation of immigrants in top wealth positions grows, their economic, social, and political influence is likely to increase as well.

Design and burn-up analyses of new type holder for silicon neutron transmutation doping.

PubMed

Komeda, Masao; Arai, Masaji; Tamai, Kazuo; Kawasaki, Kozo

2016-07-01

We have developed a new silicon irradiation holder with a neutron filter to increase the irradiation efficiency. The neutron filter is made of an alloy of aluminum and B4C particles. We fabricated a new holder based on the results of design analyses. This filter has limited use in applications requiring prolonged use due to a decrease in the amount of (10)B in B4C particles. We investigated the influence of (10)B reduction on doping distribution in a silicon ingot by using the Monte Carlo Code MVP. Copyright © 2016 Elsevier Ltd. All rights reserved.

Novel cemented cup-holding technique while performing total hip arthroplasty with navigation system.

PubMed

Takai, Hirokazu; Takahashi, Tomoki

2017-09-01

Recently, navigation systems have been more widely utilized in total hip arthroplasty. However, almost all of these systems have been developed for cementless cups. In the case of cemented total hip arthroplasty using a navigation system, a special-ordered cemented holder is needed. We propose a novel cemented cup-holding technique for navigation systems using readily available articles. We combine a cementless cup holder with an inverted cementless trial cup. The resulting apparatus is used as a cemented cup holder. The upside-down cup-holding technique is useful and permits cemented cup users to utilize a navigation system for placement of the acetabular component.

75 FR 10532 - Self-Regulatory Organizations; Notice of Filing and Immediate Effectiveness of Proposed Rule...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-08

... all similarly situated ATP Holders. 2. Statutory Basis The Exchange believes that the proposed rule... to all similarly situated ATP Holders. \\4\\ 15 U.S.C. 78f(b). \\5\\ 15 U.S.C. 78f(b)(4). B. Self...

14 CFR 135.271 - Helicopter hospital emergency medical evacuation service (HEMES).

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Helicopter hospital emergency medical....271 Helicopter hospital emergency medical evacuation service (HEMES). (a) No certificate holder may... certificate holder may assign a helicopter flight crewmember, and no flight crewmember may accept an...

14 CFR 135.271 - Helicopter hospital emergency medical evacuation service (HEMES).

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Helicopter hospital emergency medical....271 Helicopter hospital emergency medical evacuation service (HEMES). (a) No certificate holder may... certificate holder may assign a helicopter flight crewmember, and no flight crewmember may accept an...

14 CFR 135.271 - Helicopter hospital emergency medical evacuation service (HEMES).

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Helicopter hospital emergency medical....271 Helicopter hospital emergency medical evacuation service (HEMES). (a) No certificate holder may... certificate holder may assign a helicopter flight crewmember, and no flight crewmember may accept an...

14 CFR 135.271 - Helicopter hospital emergency medical evacuation service (HEMES).

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Helicopter hospital emergency medical....271 Helicopter hospital emergency medical evacuation service (HEMES). (a) No certificate holder may... certificate holder may assign a helicopter flight crewmember, and no flight crewmember may accept an...

14 CFR 135.271 - Helicopter hospital emergency medical evacuation service (HEMES).

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Helicopter hospital emergency medical....271 Helicopter hospital emergency medical evacuation service (HEMES). (a) No certificate holder may... certificate holder may assign a helicopter flight crewmember, and no flight crewmember may accept an...

49 CFR Appendix B to Part 564 - Information to be Submitted for Long Life Replaceable Light Sources of Limited Definition

Code of Federal Regulations, 2013 CFR

2013-10-01

... indexing the bulb base in the bulb holder. B. Diameter, width, depth, and surface finish of seal groove... interchangeability dimensions for indexing the bulb base in the bulb holder. B. Mating diameter, width, depth, and...

49 CFR Appendix B to Part 564 - Information to be Submitted for Long Life Replaceable Light Sources of Limited Definition

Code of Federal Regulations, 2014 CFR

2014-10-01

... indexing the bulb base in the bulb holder. B. Diameter, width, depth, and surface finish of seal groove... interchangeability dimensions for indexing the bulb base in the bulb holder. B. Mating diameter, width, depth, and...

40 CFR 86.1337-2007 - Engine dynamometer test run.

Code of Federal Regulations, 2012 CFR

2012-07-01

... engine, dynamometer, and sampling system. (iii) Change filters, etc., and leak check as necessary. (2..., loaded particulate sample filter cartridge into the filter holder assembly. It is recommended that this be done within the filter stabilization environment, with both ends of the filter holder assembly...

40 CFR 86.1337-2007 - Engine dynamometer test run.

Code of Federal Regulations, 2013 CFR

2013-07-01

... engine, dynamometer, and sampling system. (iii) Change filters, etc., and leak check as necessary. (2..., loaded particulate sample filter cartridge into the filter holder assembly. It is recommended that this be done within the filter stabilization environment, with both ends of the filter holder assembly...

40 CFR 86.1337-2007 - Engine dynamometer test run.

Code of Federal Regulations, 2010 CFR

2010-07-01

... engine, dynamometer, and sampling system. (iii) Change filters, etc., and leak check as necessary. (2..., loaded particulate sample filter cartridge into the filter holder assembly. It is recommended that this be done within the filter stabilization environment, with both ends of the filter holder assembly...

40 CFR 86.1337-2007 - Engine dynamometer test run.

Code of Federal Regulations, 2011 CFR

2011-07-01

... engine, dynamometer, and sampling system. (iii) Change filters, etc., and leak check as necessary. (2..., loaded particulate sample filter cartridge into the filter holder assembly. It is recommended that this be done within the filter stabilization environment, with both ends of the filter holder assembly...

7 CFR 1463.105 - Base quota levels for eligible quota holders.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false Base quota levels for eligible quota holders. 1463.105 Section 1463.105 Agriculture Regulations of the Department of Agriculture (Continued) COMMODITY CREDIT CORPORATION, DEPARTMENT OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS 2005-2014 TOBACCO...

18 CFR 4.96 - Amendment of exemption.

Code of Federal Regulations, 2010 CFR

2010-04-01

... design, location, method of construction or operation of its project, it must first notify the..., location, method of construction or operation of the project, the exemption holder may implement the..., method of construction or the operation of the project works, the exemption holder may not implement the...

76 FR 6199 - Enhanced Weapons, Firearms Background Checks, and Security Event Notifications

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-03

... XI. Voluntary Consensus Standards XII. Finding of No Significant Environmental Impact XIII. Paperwork... potential advantages to NRC licensees and certificate holders to enhance security. The first advantage is... advantage is that security personnel of certain licensees or certificate holders will be permitted to...

10 CFR 72.160 - Licensee and certificate holder inspection.

Code of Federal Regulations, 2011 CFR

2011-01-01

... WASTE Quality Assurance § 72.160 Licensee and certificate holder inspection. The licensee, applicant for... inspection of activities affecting quality by or for the organization performing the activity to verify.... Examinations, measurements, or tests of material or products processed must be performed for each work...

10 CFR 72.160 - Licensee and certificate holder inspection.

Code of Federal Regulations, 2010 CFR

2010-01-01

... WASTE Quality Assurance § 72.160 Licensee and certificate holder inspection. The licensee, applicant for... inspection of activities affecting quality by or for the organization performing the activity to verify.... Examinations, measurements, or tests of material or products processed must be performed for each work...

10 CFR 72.160 - Licensee and certificate holder inspection.

Code of Federal Regulations, 2013 CFR

2013-01-01

... WASTE Quality Assurance § 72.160 Licensee and certificate holder inspection. The licensee, applicant for... inspection of activities affecting quality by or for the organization performing the activity to verify.... Examinations, measurements, or tests of material or products processed must be performed for each work...

10 CFR 72.160 - Licensee and certificate holder inspection.

Code of Federal Regulations, 2012 CFR

2012-01-01

... WASTE Quality Assurance § 72.160 Licensee and certificate holder inspection. The licensee, applicant for... inspection of activities affecting quality by or for the organization performing the activity to verify.... Examinations, measurements, or tests of material or products processed must be performed for each work...

10 CFR 72.160 - Licensee and certificate holder inspection.

Code of Federal Regulations, 2014 CFR

2014-01-01

... WASTE Quality Assurance § 72.160 Licensee and certificate holder inspection. The licensee, applicant for... inspection of activities affecting quality by or for the organization performing the activity to verify.... Examinations, measurements, or tests of material or products processed must be performed for each work...

A Flexure-Based Tool Holder for Sub-(micro)m Positioning of a Single Point Cutting Tool on a Four-axis Lathe

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bono, M J; Hibbard, R L

2005-12-05

A tool holder was designed to facilitate the machining of precision meso-scale components with complex three-dimensional shapes with sub-{micro}m accuracy on a four-axis lathe. A four-axis lathe incorporates a rotary table that allows the cutting tool to swivel with respect to the workpiece to enable the machining of complex workpiece forms, and accurately machining complex meso-scale parts often requires that the cutting tool be aligned precisely along the axis of rotation of the rotary table. The tool holder designed in this study has greatly simplified the process of setting the tool in the correct location with sub-{micro}m precision. The toolmore » holder adjusts the tool position using flexures that were designed using finite element analyses. Two flexures adjust the lateral position of the tool to align the center of the nose of the tool with the axis of rotation of the B-axis, and another flexure adjusts the height of the tool. The flexures are driven by manual micrometer adjusters, each of which provides a minimum increment of motion of 20 nm. This tool holder has simplified the process of setting a tool with sub-{micro}m accuracy, and it has significantly reduced the time required to set a tool.« less

High-temperature short-time pasteurisation of human breastmilk is efficient in retaining protein and reducing the bacterial count.

PubMed

Klotz, Daniel; Joellenbeck, Mirjam; Winkler, Karl; Kunze, Mirjam; Huzly, Daniela; Hentschel, Roland

2017-05-01

Milk banks are advised to use Holder pasteurisation to inactivate the cytomegalovirus, but the process adversely affects the bioactive properties of human breastmilk. This study explored the antibacterial efficacy of an alternative high-temperature short-time (HTST) treatment of human breastmilk and its effect on marker proteins, compared with the Holder method. Breastmilk samples were obtained from 27 mothers with infants in a German neonatal intensive care unit. The samples were either heated to 62°C for five seconds using HTST or processed using Holder pasteurisation, at 63 ± 0.5°C for 30 minutes. Immunoglobulin A, lactoferrin, lysozyme, alkaline phosphatase and bile salt-stimulated lipase concentrations and bacterial colony-forming units/mL were measured before and after heating. HTST-treated samples retained higher rates of immunoglobulin A (95% versus 83%), alkaline phosphatase (6% versus 0%) and bile salt-stimulated lipase (0.8% versus 0.4%) than Holder pasteurisation samples (all p < 0.01), but not lactoferrin (32% versus 20%, p = 0.18) and lysozyme (72% versus 65%, p = 1). No difference in antibacterial efficacy was noted between the two groups (p = 0.29). Using the HTST treatment protocol retained some of the bioactive properties of human breastmilk and appeared to have similar antibacterial efficacy to Holder pasteurisation. ©2017 Foundation Acta Paediatrica. Published by John Wiley & Sons Ltd.

Foot-controlled robotic-enabled endoscope holder for endoscopic sinus surgery: A cadaveric feasibility study.

PubMed

Chan, Jason Y K; Leung, Iris; Navarro-Alarcon, David; Lin, Weiyang; Li, Peng; Lee, Dennis L Y; Liu, Yun-hui; Tong, Michael C F

2016-03-01

To evaluate the feasibility of a unique prototype foot-controlled robotic-enabled endoscope holder (FREE) in functional endoscopic sinus surgery. Cadaveric study. Using human cadavers, we investigated the feasibility, advantages, and disadvantages of the robotic endoscope holder in performing endoscopic sinus surgery with two hands in five cadaver heads, mimicking a single nostril three-handed technique. The FREE robot is relatively easy to use. Setup was quick, taking less than 3 minutes from docking the robot at the head of the bed to visualizing the middle meatus. The unit is also relatively small, takes up little space, and currently has four degrees of freedom. The learning curve for using the foot control was short. The use of both hands was not hindered by the presence of the endoscope in the nasal cavity. The tremor filtration also aided in the smooth movement of the endoscope, with minimal collisions. The FREE endoscope holder in an ex-vivo cadaver test corroborated the feasibility of the robotic prototype, which allows for a two-handed approach to surgery equal to a single nostril three-handed technique without the holder that may reduce operating time. Further studies will be needed to evaluate its safety profile and use in other areas of endoscopic surgery. NA. Laryngoscope, 126:566-569, 2016. © 2015 The American Laryngological, Rhinological and Otological Society, Inc.

The Effect of Simulated Flash-Heat Pasteurization on Immune Components of Human Milk

PubMed Central

Daniels, Brodie; Schmidt, Stefan; King, Tracy; Israel-Ballard, Kiersten; Amundson Mansen, Kimberly; Coutsoudis, Anna

2017-01-01

A pasteurization temperature monitoring system has been designed using FoneAstra, a cellphone-based networked sensing system, to monitor simulated flash-heat (FH) pasteurization. This study compared the effect of the FoneAstra FH (F-FH) method with the Sterifeed Holder method currently used by human milk banks on human milk immune components (immunoglobulin A (IgA), lactoferrin activity, lysozyme activity, interleukin (IL)-8 and IL-10). Donor milk samples (N = 50) were obtained from a human milk bank, and pasteurized. Concentrations of IgA, IL-8, IL-10, lysozyme activity and lactoferrin activity were compared to their controls using the Student’s t-test. Both methods demonstrated no destruction of interleukins. While the Holder method retained all lysozyme activity, the F-FH method only retained 78.4% activity (p < 0.0001), and both methods showed a decrease in lactoferrin activity (71.1% Holder vs. 38.6% F-FH; p < 0.0001) and a decrease in the retention of total IgA (78.9% Holder vs. 25.2% F-FH; p < 0.0001). Despite increased destruction of immune components compared to Holder pasteurization, the benefits of F-FH in terms of its low cost, feasibility, safety and retention of immune components make it a valuable resource in low-income countries for pasteurizing human milk, potentially saving infants’ lives. PMID:28241418

Rural Allied Health Scholarships: do they make a difference?

PubMed

Devine, Susan G; Williams, Gary; Nielsen, Ilsa

2013-01-01

The problem of recruiting and retaining a qualified rural and remote health workforce is well recognised and a number of strategies have been put in place to address this issue, including the use of bonded scholarship programs. However there is a paucity of evidence regarding the impact of scholarships on workforce outcomes particularly in relation to allied health professionals. This project involved a review of the Queensland Health Rural Scholarship Scheme (Allied Health) (QHRSS-AH) including impacts on those engaged with the scholarship program and for the funding organisation. Specifically this study aimed to examine the profile of the QHRSS-AH recipients from 2000 to 2010 including graduate recruitment outcomes and retention within the scholarship program. It also explored the influence of the QHRSS-AH on early career practice location decisions and the features of the scheme that influenced motivation to be involved as either a scholarship holder or manager, perceived barriers to employment of scholarship holders in rural or remote services, experiences of scholarship holders as new graduates in rural and remote services and views on support requirements. A mixed methods study was conducted involving quantitative analysis of existing Queensland Health scholarship data and a qualitative study that used one-on-one, in-depth telephone interviews with 17 past or current scholarship holders and 11 managers of scholarship holders. Of the 146 participants, 69.2% had completed or were completing the service period (41.1% were post-bond and 28.1% were currently completing the service period). Of the remainder, 14.4% were still completing the study period, 2.7% had deferred the service period and 13.7% had broken service bonds. Scholarship holders and managers indicated support for scholarships. Key motivators for applying for a scholarship were financial and job security upon graduation, although the general appeal of and preference for rural practice was an underlying motivator. Regardless of receiving a scholarship, most scholarship recipients reported they would have gone into rural and remote practice. Professional and clinical support and supervision, supportive work environment and culture, mentoring and professional development are important for retention. New graduates need extra support to assist in the undergraduate-to-practice transition and both scholarship holders and managers emphasised the important role played by health services in having well defined, consistent, operational processes that orient and support new graduates particularly in relation to supervision, mentoring and professional development. Although scholarship holders and their managers support the rural scholarship program, aspects of the scholarships in their current form require consideration in light of current workforce supply and demand and changing professional structures within the organisation. While many scholarship holders felt well supported as a new graduate entering rural practice, others identified gaps in relation to their experiences and the support they received. Opportunities exist for more standardised approaches across all services to strengthen the support structures that are in place, particularly for new graduates.

21 CFR 882.4460 - Neurosurgical head holder (skull clamp).

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Neurosurgical head holder (skull clamp). 882.4460 Section 882.4460 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES NEUROLOGICAL DEVICES Neurological Surgical Devices § 882.4460 Neurosurgical head...

14 CFR 183.49 - Authorized functions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Authorized functions. 183.49 Section 183.49... functions. (a) Consistent with an ODA Holder's qualifications, the Administrator may delegate any function... ODA Unit may perform only those functions, and is subject to the limitations, listed in the ODA Holder...

77 FR 31050 - Self-Regulatory Organizations; NYSE Arca, Inc.; Notice of Filing and Immediate Effectiveness of...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-24

...-Regulatory Organizations; NYSE Arca, Inc.; Notice of Filing and Immediate Effectiveness of Proposed Rule... threshold qualifications and corresponding rates applicable to Option Trading Permit (``OTP'') Holder and... restructure the threshold qualifications and corresponding rates applicable to OTP Holder and OTP Firm...

78 FR 57617 - Submission for OMB Review; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-19

...; cost recovery and fee payment, 2 hours; landing reports, 2 minutes. Burden Hours: 42. Needs and Uses: This request is for extension of a current information collection. National Marine Fisheries Service... holders in order to process applications to ensure that IFQ allocation holders are provided a statement of...

77 FR 49444 - Agency Information Collection Activities: Proposed Collection Renewal; Comment Request (3064-0152)

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-16

...: Office of Information and Regulatory Affairs, Office of Management and Budget, New Executive Office... regarding identity theft with respect to their account holders and customers; (ii) regulations requiring... implementing the guidelines to identify possible risks to account holders or customers or to the safety and...

7 CFR 762.144 - Repurchase of guaranteed portion from a secondary market holder.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 7 2014-01-01 2014-01-01 false Repurchase of guaranteed portion from a secondary market holder. 762.144 Section 762.144 Agriculture Regulations of the Department of Agriculture (Continued) FARM SERVICE AGENCY, DEPARTMENT OF AGRICULTURE SPECIAL PROGRAMS GUARANTEED FARM LOANS § 762.144...

10 CFR 71.8 - Deliberate misconduct.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 2 2011-01-01 2011-01-01 false Deliberate misconduct. 71.8 Section 71.8 Energy NUCLEAR... § 71.8 Deliberate misconduct. (a) This section applies to any— (1) Licensee; (2) Certificate holder; (3... deliberate misconduct that causes or would have caused, if not detected, a licensee, certificate holder...

10 CFR 71.8 - Deliberate misconduct.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 2 2010-01-01 2010-01-01 false Deliberate misconduct. 71.8 Section 71.8 Energy NUCLEAR... § 71.8 Deliberate misconduct. (a) This section applies to any— (1) Licensee; (2) Certificate holder; (3... deliberate misconduct that causes or would have caused, if not detected, a licensee, certificate holder...

10 CFR 71.8 - Deliberate misconduct.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 2 2013-01-01 2013-01-01 false Deliberate misconduct. 71.8 Section 71.8 Energy NUCLEAR... § 71.8 Deliberate misconduct. (a) This section applies to any— (1) Licensee; (2) Certificate holder; (3... deliberate misconduct that causes or would have caused, if not detected, a licensee, certificate holder...

10 CFR 71.8 - Deliberate misconduct.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 2 2014-01-01 2014-01-01 false Deliberate misconduct. 71.8 Section 71.8 Energy NUCLEAR... § 71.8 Deliberate misconduct. (a) This section applies to any— (1) Licensee; (2) Certificate holder; (3... deliberate misconduct that causes or would have caused, if not detected, a licensee, certificate holder...

10 CFR 71.8 - Deliberate misconduct.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 2 2012-01-01 2012-01-01 false Deliberate misconduct. 71.8 Section 71.8 Energy NUCLEAR... § 71.8 Deliberate misconduct. (a) This section applies to any— (1) Licensee; (2) Certificate holder; (3... deliberate misconduct that causes or would have caused, if not detected, a licensee, certificate holder...

Measured thermal and fast neutron fluence rates for ATF-1 holders during ATR cycle 160A

DOE Office of Scientific and Technical Information (OSTI.GOV)

Walker, B. J.; Miller, D. T.

This report contains the thermal (2200 m/s) and fast (E>1MeV) neutron fluence rate data for the ATF-1 holders located in core for ATR Cycle 160A which were measured by the Radiation Measurements Laboratory (RML).

Tool Releases Optical Elements From Spring Brackets

NASA Technical Reports Server (NTRS)

Gum, J. S.

1984-01-01

Threaded hooks retract bracket arms holding element. Tool uses three hooks with threaded shanks mounted in ring-shaped holder to pull on tabs to release optical element. One person can easily insert or remove optical element (such as prism or lens) from spring holder or bracket with minimal risk of damage.

12 CFR 239.22 - Charter amendments.

Code of Federal Regulations, 2013 CFR

2013-01-01

... of dividends and of sinking fund, retirement fund, or other retirement payments, if any, to which..., dissolution, or winding up of the subsidiary holding company, the holders of the common stock (and the holders... of stock having preference over the common stock in the liquidation, dissolution, or winding up of...

12 CFR 239.22 - Charter amendments.

Code of Federal Regulations, 2012 CFR

2012-01-01

... of dividends and of sinking fund, retirement fund, or other retirement payments, if any, to which..., dissolution, or winding up of the subsidiary holding company, the holders of the common stock (and the holders... of stock having preference over the common stock in the liquidation, dissolution, or winding up of...

27 CFR 555.105 - Distributions to nonlicensees, nonpermittees, and limited permittees.

Code of Federal Regulations, 2010 CFR

2010-04-01

... employee of a common or contract carrier transporting explosive materials to a nonlicensee or nonpermittee... licensee's business premises are located, the holder of the limited permit presents in person or by mail... transport explosive materials from the distributor to a holder of a limited permit: (A) The limited...

26 CFR 1.331-1 - Corporate liquidations.

Code of Federal Regulations, 2010 CFR

2010-04-01

...) Reporting requirement—(1) General rule. Every significant holder that transfers stock to the issuing...) The fair market value and basis of the stock transferred by the significant holder to the issuing... stock of the issuing corporation if the stock owned by such person is publicly traded; or (B) Owned at...

26 CFR 1.302-2 - Redemptions not taxable as dividends.

Code of Federal Regulations, 2010 CFR

2010-04-01

... stock to the issuing corporation in exchange for property from such corporation must include on or with... SIGNIFICANT HOLDER OF THE STOCK OF [INSERT NAME AND EMPLOYER IDENTIFICATION NUMBER (IF ANY) OF ISSUING... of the stock transferred by the significant holder to the issuing corporation; and (ii) A description...

18 CFR 4.104 - Amendment of exemption.

Code of Federal Regulations, 2010 CFR

2010-04-01

... change the design, location, method of construction or operation of its project, it must first notify the..., location, method of construction or operation of the project, the exemption holder may implement the..., method of construction or the operation of the project works, the exemption holder may not implement the...

CDL self-certification and medical examiner's certificate reporting : protect your CDL, compliance is easy, find out how.

DOT National Transportation Integrated Search

2011-01-01

Starting Jan. 30, 2012, the Iowa Department of Transportation (DOT) will implement new federal regulations that require all CDL holders and applicants to certify the type of driving they do, and require interstate CDL holders that carry a Medical Exa...

21 CFR 892.1880 - Wall-mounted radiographic cassette holder.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Wall-mounted radiographic cassette holder. 892.1880 Section 892.1880 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.1880 Wall-mounted...

14 CFR 135.145 - Aircraft proving and validation tests.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Aircraft proving and validation tests. 135... Aircraft and Equipment § 135.145 Aircraft proving and validation tests. (a) No certificate holder may...) Validation testing is required to determine that a certificate holder is capable of conducting operations...

14 CFR 135.145 - Aircraft proving and validation tests.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Aircraft proving and validation tests. 135... Aircraft and Equipment § 135.145 Aircraft proving and validation tests. (a) No certificate holder may...) Validation testing is required to determine that a certificate holder is capable of conducting operations...

14 CFR 135.145 - Aircraft proving and validation tests.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Aircraft proving and validation tests. 135... Aircraft and Equipment § 135.145 Aircraft proving and validation tests. (a) No certificate holder may...) Validation testing is required to determine that a certificate holder is capable of conducting operations...

14 CFR 135.145 - Aircraft proving and validation tests.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Aircraft proving and validation tests. 135... Aircraft and Equipment § 135.145 Aircraft proving and validation tests. (a) No certificate holder may...) Validation testing is required to determine that a certificate holder is capable of conducting operations...

14 CFR 135.145 - Aircraft proving and validation tests.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Aircraft proving and validation tests. 135... Aircraft and Equipment § 135.145 Aircraft proving and validation tests. (a) No certificate holder may...) Validation testing is required to determine that a certificate holder is capable of conducting operations...

12 CFR 563b.465 - Do account holders retain any voting rights based on their liquidation sub-accounts?

Code of Federal Regulations, 2010 CFR

2010-01-01

... based on their liquidation sub-accounts? 563b.465 Section 563b.465 Banks and Banking OFFICE OF THRIFT... Account § 563b.465 Do account holders retain any voting rights based on their liquidation sub-accounts... their liquidation sub-accounts. ...

A study of PC-based ultrasonic goniometer system of surface properties and characterization of materials

NASA Astrophysics Data System (ADS)

Sani, S.; Saad, M. H. Md; Jamaludin, N.; Ismail, M. P.; Mohd, S.; Mustapha, I.; Masenwat, N. A.; Tengku Amran, T. S.; Megat Ahmad, M. H. A.

2018-01-01

This paper discussed the design and development of a portable PC-based ultrasonic goniometer system that can be used to study material properties using ultrasonic wave. The system utilizes an ultrasonic pulse-receiver card model attached to computer notebook for signal display. A new specific software package (GoNIO) was developed to control the operation of the scanner, displaying the data and analyze characteristics of materials. System testing was carried out using samples with cubic dimension of about 10 mm x 20 mm x 30 mm. This size allows the sample to be fitted into the goniometer specimen holder and immersed in a liquid during measurement. The sample was rotated from incident angle of 0° to 90° during measurement and the amplitude reflected signals were recorded at every one degree of rotation. Immersion transducers were used to generate and receive the ultrasounds that pass through the samples. Longitudinal, shear and Rayleigh wave measurements were performed on the samples to determine the Dynamic Young’s Modulus. Results of measurements are explained and discussed.

In situ degradation studies of two-dimensional WSe₂-graphene heterostructures.

PubMed

Wang, B; Eichfield, S M; Wang, D; Robinson, J A; Haque, M A

2015-09-14

Heterostructures of two-dimensional materials can be vulnerable to thermal degradation due to structural and interfacial defects as well as thermal expansion mismatch, yet a systematic study does not exist in the literature. In this study, we investigate the degradation of freestanding WSe2-graphene heterostructures due to heat and charge flow by performing in situ experiments inside a transmission electron microscope. Experimental results show that purely thermal loading requires higher temperatures (>850 °C), about 150 °C higher than that under combined electrical and thermal loading. In both cases, selenium is the first element to decompose and migration of silicon atoms from the test structure to the freestanding specimen initiates rapid degradation through the formation of tungsten disilicide and silicon carbide. The role of the current flow is to enhance the migration of silicon from the sample holder and to knock-out the selenium atoms. The findings of this study provide fundamental insights into the degradation of WSe2-graphene heterostructures and inspire their application in electronics for use in harsh environments.

Studying Dynamic Processes of Nano-sized Objects in Liquid using Scanning Transmission Electron Microscopy.

PubMed

Hermannsdörfer, Justus; de Jonge, Niels

2017-02-05

Samples fully embedded in liquid can be studied at a nanoscale spatial resolution with Scanning Transmission Electron Microscopy (STEM) using a microfluidic chamber assembled in the specimen holder for Transmission Electron Microscopy (TEM) and STEM. The microfluidic system consists of two silicon microchips supporting thin Silicon Nitride (SiN) membrane windows. This article describes the basic steps of sample loading and data acquisition. Most important of all is to ensure that the liquid compartment is correctly assembled, thus providing a thin liquid layer and a vacuum seal. This protocol also includes a number of tests necessary to perform during sample loading in order to ensure correct assembly. Once the sample is loaded in the electron microscope, the liquid thickness needs to be measured. Incorrect assembly may result in a too-thick liquid, while a too-thin liquid may indicate the absence of liquid, such as when a bubble is formed. Finally, the protocol explains how images are taken and how dynamic processes can be studied. A sample containing AuNPs is imaged both in pure water and in saline.

Studying Dynamic Processes of Nano-sized Objects in Liquid using Scanning Transmission Electron Microscopy

PubMed Central

Hermannsdörfer, Justus; de Jonge, Niels

2017-01-01

Samples fully embedded in liquid can be studied at a nanoscale spatial resolution with Scanning Transmission Electron Microscopy (STEM) using a microfluidic chamber assembled in the specimen holder for Transmission Electron Microscopy (TEM) and STEM. The microfluidic system consists of two silicon microchips supporting thin Silicon Nitride (SiN) membrane windows. This article describes the basic steps of sample loading and data acquisition. Most important of all is to ensure that the liquid compartment is correctly assembled, thus providing a thin liquid layer and a vacuum seal. This protocol also includes a number of tests necessary to perform during sample loading in order to ensure correct assembly. Once the sample is loaded in the electron microscope, the liquid thickness needs to be measured. Incorrect assembly may result in a too-thick liquid, while a too-thin liquid may indicate the absence of liquid, such as when a bubble is formed. Finally, the protocol explains how images are taken and how dynamic processes can be studied. A sample containing AuNPs is imaged both in pure water and in saline. PMID:28190028

Three dimensional reconstruction of InGaN nanodisks in GaN nanowires: Improvement of the nanowire sample preparation to avoid missing wedge effects

NASA Astrophysics Data System (ADS)

Gries, Katharina Ines; Schlechtweg, Julian; Hille, Pascal; Schörmann, Jörg; Eickhoff, Martin; Volz, Kerstin

2017-10-01

Scanning transmission electron microscopy is an extremely useful method to image small features with a size in the range of a few nanometers and below. But it must be taken into account that such images are projections of the sample and do not necessarily represent the real three dimensional structure of the specimen. By applying electron tomography this problem can be overcome. In our work GaN nanowires including InGaN nanodisks were investigated. To reduce the effect of the missing wedge a single nanowire was removed from the underlying silicon substrate using a manipulator needle and attached to a tomography holder. Since this sample exhibits the same thickness of few tens of nanometers in all directions normal to the tilt axis, this procedure allows a sample tilt of ±90°. Reconstruction of the received data reveals a split of the InGaN nanodisks into a horizontal continuation of the (0 0 0 1 bar) central facet and a declined {1 0 1 bar l} facet (with l = -2 or -3).

Infectious microorganisms in mice (Mus musculus) purchased from commercial pet shops in Germany.

PubMed

Dammann, P; Hilken, G; Hueber, B; Köhl, W; Bappert, M T; Mähler, M

2011-10-01

In this study, we investigated the prevalence of infectious microorganisms (viruses, bacteria, fungi and eukaryotic parasites) in mice from different pet shops in Germany; such animals may compromise the hygienic integrity of laboratory animal vivaria if private pet holders act as unintended vectors of infections carried by them. House mice sold as pets or feed specimens were purchased from different pet shops and tested for a comprehensive panel of unwanted microorganisms. We found a number of microorganisms in these pet shop mice, the most prevalent of which were Helicobacter species (92.9%), mouse parvovirus (89.3%), mouse hepatitis virus (82.7%), Pasteurella pneumotropica (71.4%) and Syphacia species (57.1%). Several microorganisms (e.g. mouse parvovirus, Theiler's murine encephalomyelitis virus, pneumonia virus of mice, Encephalitozoon cuniculi, Clostridium piliforme) had considerably higher prevalences than those reported in similar studies on wild mice from North America, Europe or Australia. Our study shows that direct contact with pet shop mice may constitute a risk for laboratory animal vivaria if hygienic precautions are not taken. However, even relatively simple precautions seem effective enough to hold the risk at bay.

Fundamental and applied research on core engine/combustion noise of aircraft engines

NASA Technical Reports Server (NTRS)

Plett, E. G.; Leshner, M. D.; Summerfield, M.

1974-01-01

Some results of a study of the importance of geometrical features of the combustor to combustion roughness and resulting noise are presented. Comparison is made among a perforated can flame holder, a plane slotted flame holder and a plane slotted flame holder which introduces two counter swirling streams. The latter is found to permit the most stable, quiet combustion. Crosscorrelations between the time derivative of chamber pressure fluctuations and far field noise are found to be stronger than between the far field noise and the direct chamber pressure signal. Temperature fluctuations in the combustor nozzle are also found to have a reasonably strong crosscorrelation with far field sound.

A parabolic variational inequality arising from the valuation of strike reset options

NASA Astrophysics Data System (ADS)

Yang, Zhou; Yi, Fahuai; Dai, Min

A strike reset option is an option that allows its holder to reset the strike price to the prevailing underlying asset price at a moment chosen by the holder. The pricing model of the option can be formulated as a one-dimensional parabolic variational inequality, or equivalently, a free boundary problem, where the free boundary just corresponds to the optimal reset strategy adopted by the holder of the option. This paper is concerned with the theoretical analysis of the model. The existence and uniqueness of the solution are established. Furthermore, we study properties of the free boundary. The monotonicity and C smoothness of the free boundary are proven in some situations.

Ignitability test method and apparatus

NASA Technical Reports Server (NTRS)

Bement, Laurence J. (Inventor); Bailey, James W. (Inventor); Schimmel, Morry L. (Inventor)

1991-01-01

An apparatus for testing ignitability of an initiator includes a body having a central cavity, an initiator holder for holding the initiator over the central cavity of the body, an ignition material holder disposed in the central cavity of the body and having a cavity facing the initiator holder which receives a measured quantity of ignition material to be ignited by the initiator. It contains a chamber in communication with the cavity of the ignition material and the central cavity of the body, and a measuring system for analyzing pressure characteristics generated by ignition of the ignition material by the initiator. The measuring system includes at least one transducer coupled with an oscillograph for recording pressure traces generated by ignition.

Photo-polymerization shrinkage-stress kinetics in resin-composites: methods development.

PubMed

Watts, D C; Marouf, A S; Al-Hindi, A M

2003-01-01

Studies of free shrinkage-strain kinetics on restoratives have begun to multiply. However, there have been fewer investigations of the more difficult problem of concurrent stress-kinetic measurements. The aim was to outline design parameters for a new methodology for this problem, amenable especially to light-cured materials, and to present illustrative results for a range of restorative composites. Absolute values of stress measurable for a given material and geometry are dependent upon the stiffness of the measurement system. In an infinitely stiff system, the measured stress would also tend towards infinity. Real teeth and their cavities are not infinitely stiff; they have elastic and visco-elastic compliance. Consequently, it is important that some minimal, but essentially constant compliance be allowed, whatever the final or time-dependent modulus of the material may be. This goal has been realised by measurement of the time-development, for a disk-geometry specimen (phi=10, h approximately 1.0 mm) of stress (S(r)), with a calibrated cantilever beam-geometry load cell. A novel specimen-holder design was used for this purpose, held in a rigid base assembly. Specimen thicknesses (or gap-widths) of 0.8 and 1.2 mm were specifically investigated on four representative resin-composites. Concurrent measurements were made of the end-displacement of the cantilever load cell, relative to a lower glass plate retaining the specimen. Load-calibration of the cantilever load cell gave an end-displacement per unit stress of circa 6 microm/MPa. This compares with literature values for cuspal compliance or displacement of circa 20 microm. Re-normalisation of the stress-data was implemented. This was accomplished assuming Hooke's law behavior at each instant and equivalent to a stiffer system, with a correction (multiplier) factor of 4 on the raw-stress values. For the materials examined, resultant maximum-stress levels determined were circa 5-8 MPa Stress-levels obtained at 1.2mm thickness were slightly higher (11-15%) than the level of stress obtained at 0.8 mm thickness. This is attributable to the greater mass of material undergoing shrinkage at 1.2 mm, offset slightly by the different C-factors. The new device is a practical and self-contained system for rapid and accurate measurement of stress-kinetics in photo-polymerising and also self-cure materials.

12 CFR 563c.102 - Financial statement presentation.

Code of Federal Regulations, 2010 CFR

2010-01-01

... sheet date, disclose in a note the aggregate dollar amount of loans (exclusive of loans to any such... holders, out of future earnings) and the rights, if any, of holders in the event of default, including the effect, if any, on junior securities in the event a required dividend, sinking fund, or other redemption...

17 CFR 240.14b-1 - Obligation of registered brokers and dealers in connection with the prompt forwarding of certain...

Code of Federal Regulations, 2011 CFR

2011-04-01

... security holders, proxy statement, information statement, or Notice of Internet Availability of Proxy...(e)(1) (with respect to annual reports to security holders, proxy statements, and Notices of Internet..., information statements, and Notices of Internet Availability of Proxy Materials) applicable to registrants...

17 CFR 240.14b-1 - Obligation of registered brokers and dealers in connection with the prompt forwarding of certain...

Code of Federal Regulations, 2013 CFR

2013-04-01

... security holders, proxy statement, information statement, or Notice of Internet Availability of Proxy...(e)(1) (with respect to annual reports to security holders, proxy statements, and Notices of Internet..., information statements, and Notices of Internet Availability of Proxy Materials) applicable to registrants...

17 CFR 240.14b-1 - Obligation of registered brokers and dealers in connection with the prompt forwarding of certain...

Code of Federal Regulations, 2010 CFR

2010-04-01

... security holders, proxy statement, information statement, or Notice of Internet Availability of Proxy...(e)(1) (with respect to annual reports to security holders, proxy statements, and Notices of Internet..., information statements, and Notices of Internet Availability of Proxy Materials) applicable to registrants...

17 CFR 240.14b-1 - Obligation of registered brokers and dealers in connection with the prompt forwarding of certain...

Code of Federal Regulations, 2012 CFR

2012-04-01

... security holders, proxy statement, information statement, or Notice of Internet Availability of Proxy...(e)(1) (with respect to annual reports to security holders, proxy statements, and Notices of Internet..., information statements, and Notices of Internet Availability of Proxy Materials) applicable to registrants...

17 CFR 240.14b-1 - Obligation of registered brokers and dealers in connection with the prompt forwarding of certain...

Code of Federal Regulations, 2014 CFR

2014-04-01

... security holders, proxy statement, information statement, or Notice of Internet Availability of Proxy...(e)(1) (with respect to annual reports to security holders, proxy statements, and Notices of Internet..., information statements, and Notices of Internet Availability of Proxy Materials) applicable to registrants...

77 FR 7010 - Clarification of Policy Regarding Approved Training Programs; Correction

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-10

... approval multiple curriculums for a particular crewmember position and aircraft make/model/variant. For example, a part 135 certificate holder may have a an initial new-hire curriculum designed to meet the... certificate holder may then also apply for a reduced new hire curriculum for pilots that have previous...

50 CFR 679.45 - IFQ cost recovery program.

Code of Federal Regulations, 2014 CFR

2014-10-01

... as GAF is added to the value of the IFQ permit holder's landed IFQ, and the sum is multiplied by the... ADMINISTRATION, DEPARTMENT OF COMMERCE (CONTINUED) FISHERIES OF THE EXCLUSIVE ECONOMIC ZONE OFF ALASKA Individual... recovery liability based on the value of all landed IFQ and GAF derived from the permit holder's IFQ permit...

21 CFR 314.95 - Notice of certification of invalidity or noninfringement of a patent.

Code of Federal Regulations, 2010 CFR

2010-04-01

... of business within the United States, the application holder's attorney, agent, or other authorized official. The name and address of the application holder or its attorney, agent, or authorized official may be obtained from the Orange Book Staff, Office of Generic Drugs, 7500 Standish Pl., Rockville, MD...

21 CFR 876.5820 - Hemodialysis system and accessories.

Code of Federal Regulations, 2010 CFR

2010-04-01

... chair without a scale, the dialyzer holder set, dialysis tie gun and ties, and hemodialysis start/stop..., dialyzer holder set, and dialysis tie gun and ties. The devices subject to this paragraph (b)(2) are exempt from the premarket notification procedures in subpart E of part 807 of this chapter subject to the...

75 FR 69478 - Self-Regulatory Organizations; C2 Options Exchange, Incorporated: Notice of Filing and Immediate...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-12

... surveillance or communications rules. Further, there is no change to, or impact on, the Exchange's market... directly to C2 Permit Holders (``Permit Holders'') and their customers, including Sponsored Users. STS may... customers, including Sponsored Users, through the use of a sublicense. However, whether the workstation...

49 CFR Appendix B to Part 564 - Information To Be Submitted for Long Life Replaceable Light Sources of Limited Definition

Code of Federal Regulations, 2011 CFR

2011-10-01

.... A. Angular locations, diameters, key/keyway sizes, and any other interchangeability dimensions for... base in the bulb holder such as tabs, keys, keyways, surface, etc. III. Bulb Holder Interchangeability Dimensions and Tolerances. A. Mating angular locations, diameters, key/keyway sizes, any other...

49 CFR Appendix B to Part 564 - Information To Be Submitted for Long Life Replaceable Light Sources of Limited Definition

Code of Federal Regulations, 2012 CFR

2012-10-01

.... A. Angular locations, diameters, key/keyway sizes, and any other interchangeability dimensions for... base in the bulb holder such as tabs, keys, keyways, surface, etc. III. Bulb Holder Interchangeability Dimensions and Tolerances. A. Mating angular locations, diameters, key/keyway sizes, any other...

14 CFR 43.3 - Persons authorized to perform maintenance, preventive maintenance, rebuilding, and alterations.

Code of Federal Regulations, 2012 CFR

2012-01-01

... maintenance are a result of a known or suspected mechanical difficulty or malfunction that occurred en route... is authorized in writing by the certificate holder for each item of preventive maintenance that the... satisfactorily completed an approved training program and is authorized in writing by the certificate holder to...

33 CFR 125.33 - Holders of Coast Guard Port Security Cards.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Holders of Coast Guard Port... Card are such as to warrant the belief that his presence on waterfront facilities and port and harbor... as to warrant the belief that his presence on waterfront facilities, and port and harbor areas...

33 CFR 125.35 - Notice by Commandant.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 33 Navigation and Navigable Waters 2 2012-07-01 2012-07-01 false Notice by Commandant. 125.35... applicant or holder are such as to warrant the belief that his presence on waterfront facilities, and port... applicant or holder are such as to warrant the belief that his presence on waterfront facilities, and port...

33 CFR 125.33 - Holders of Coast Guard Port Security Cards.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 33 Navigation and Navigable Waters 2 2014-07-01 2014-07-01 false Holders of Coast Guard Port... Card are such as to warrant the belief that his presence on waterfront facilities and port and harbor... as to warrant the belief that his presence on waterfront facilities, and port and harbor areas...

33 CFR 125.35 - Notice by Commandant.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 33 Navigation and Navigable Waters 2 2014-07-01 2014-07-01 false Notice by Commandant. 125.35... applicant or holder are such as to warrant the belief that his presence on waterfront facilities, and port... applicant or holder are such as to warrant the belief that his presence on waterfront facilities, and port...

33 CFR 125.35 - Notice by Commandant.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Notice by Commandant. 125.35... applicant or holder are such as to warrant the belief that his presence on waterfront facilities, and port... applicant or holder are such as to warrant the belief that his presence on waterfront facilities, and port...

33 CFR 125.33 - Holders of Coast Guard Port Security Cards.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 33 Navigation and Navigable Waters 2 2012-07-01 2012-07-01 false Holders of Coast Guard Port... Card are such as to warrant the belief that his presence on waterfront facilities and port and harbor... as to warrant the belief that his presence on waterfront facilities, and port and harbor areas...

33 CFR 125.33 - Holders of Coast Guard Port Security Cards.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 33 Navigation and Navigable Waters 2 2013-07-01 2013-07-01 false Holders of Coast Guard Port... Card are such as to warrant the belief that his presence on waterfront facilities and port and harbor... as to warrant the belief that his presence on waterfront facilities, and port and harbor areas...

33 CFR 125.35 - Notice by Commandant.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 2 2011-07-01 2011-07-01 false Notice by Commandant. 125.35... applicant or holder are such as to warrant the belief that his presence on waterfront facilities, and port... applicant or holder are such as to warrant the belief that his presence on waterfront facilities, and port...

33 CFR 125.33 - Holders of Coast Guard Port Security Cards.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 2 2011-07-01 2011-07-01 false Holders of Coast Guard Port... Card are such as to warrant the belief that his presence on waterfront facilities and port and harbor... as to warrant the belief that his presence on waterfront facilities, and port and harbor areas...

33 CFR 125.35 - Notice by Commandant.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 33 Navigation and Navigable Waters 2 2013-07-01 2013-07-01 false Notice by Commandant. 125.35... applicant or holder are such as to warrant the belief that his presence on waterfront facilities, and port... applicant or holder are such as to warrant the belief that his presence on waterfront facilities, and port...

Psychometric Reanalysis of Happiness, Temperament, and Spirituality Scales with Children in Faith-Based Elementary Schools

ERIC Educational Resources Information Center

Cleveland, Richard E.

2014-01-01

This dissertation performed an investigation of the psychometric properties of six instruments used in the 2012 Happiness Project research study. The project revisited the 2010 study conducted by Holder, Coleman, and Wallace. Holder et al. (2010) investigated the relationships among variables relating to student happiness and spirituality while…

75 FR 69745 - Aging Airplane Program: Widespread Fatigue Damage

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-15

... prevent 1.5 days of down time associated with emergency ADs. 3. New Part 26 for Design Approval Holders... because they had high-time airplanes that were near or over their design service goals. They include the... design approval holders to evaluate their airplanes to establish a limit of validity of the engineering...

77 FR 34445 - Self-Regulatory Organizations; NYSE Arca, Inc.; Notice of Filing and Immediate Effectiveness of...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-11

... Outsourcing Solutions, Inc. as an NYSE Arca ETP Holder and OTP Holder, Subject to Apex Clearing Complying With... Corporation, f/k/a Ridge Clearing and Outsourcing Solutions, Inc. (``Apex Clearing'') as an NYSE Arca ETP... Clearing & Outsourcing Solutions, Inc. Prior to the transaction, Ridge Clearing & Outsourcing Solutions...

76 FR 61999 - Policy Statement: Inappropriate Design Approval Holder (DAH) Restrictions on the Use and...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-06

.... FOR FURTHER INFORMATION CONTACT: John Cerra, Aerospace Engineer, Federal Aviation Administration..., distribution, and use of ICAs, by submitting such written data, views, or arguments to the address or FAX... holder of a design approval to furnish at least one set of complete Instructions for Continued...

26 CFR 25.2514-1 - Transfers under power of appointment.

Code of Federal Regulations, 2010 CFR

2010-04-01

... fiduciary capacity, whereby the holder has no power to enlarge or shift any of the beneficial interests... not consist of any power or right to enlarge or shift the beneficial interest of any beneficiary... identity of its holders is not ascertainable until after the date the instrument takes effect. However, if...

17 CFR 240.14c-101 - Schedule 14C. Information required in information statement.

Code of Federal Regulations, 2014 CFR

2014-04-01

... separate copy of the annual report to security holders, information statement, or Notice of Internet... annual reports to security holders, information statements, or Notices of Internet Availability of Proxy... 17 Commodity and Securities Exchanges 4 2014-04-01 2014-04-01 false Schedule 14C. Information...

17 CFR 240.14c-101 - Schedule 14C. Information required in information statement.

Code of Federal Regulations, 2013 CFR

2013-04-01

... separate copy of the annual report to security holders, information statement, or Notice of Internet... annual reports to security holders, information statements, or Notices of Internet Availability of Proxy... 17 Commodity and Securities Exchanges 3 2013-04-01 2013-04-01 false Schedule 14C. Information...

17 CFR 240.14c-101 - Schedule 14C. Information required in information statement.

Code of Federal Regulations, 2012 CFR

2012-04-01

... separate copy of the annual report to security holders, information statement, or Notice of Internet... annual reports to security holders, information statements, or Notices of Internet Availability of Proxy... 17 Commodity and Securities Exchanges 3 2012-04-01 2012-04-01 false Schedule 14C. Information...

30 CFR 585.107 - How do I show that I am qualified to be a lessee or grant holder?

Code of Federal Regulations, 2013 CFR

2013-07-01

... include: (1) Descriptions of international or domestic experience with renewable energy projects or other types of electric-energy-related projects; and (2) Information establishing access to sufficient capital... lessee or grant holder? 585.107 Section 585.107 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT...

30 CFR 585.107 - How do I show that I am qualified to be a lessee or grant holder?

Code of Federal Regulations, 2014 CFR

2014-07-01

... include: (1) Descriptions of international or domestic experience with renewable energy projects or other types of electric-energy-related projects; and (2) Information establishing access to sufficient capital... lessee or grant holder? 585.107 Section 585.107 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT...

30 CFR 585.107 - How do I show that I am qualified to be a lessee or grant holder?

Code of Federal Regulations, 2012 CFR

2012-07-01

... include: (1) Descriptions of international or domestic experience with renewable energy projects or other types of electric-energy-related projects; and (2) Information establishing access to sufficient capital... lessee or grant holder? 585.107 Section 585.107 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT...

38 CFR 36.4279 - Extensions and reamortizations.

Code of Federal Regulations, 2010 CFR

2010-07-01

.... (a) Provided the debtor(s) is (are) a reasonable credit risk(s), as determined by the holder based... debtor(s), be extended in the event of default, to avoid imminent default, or in any other case where the...) is (are) a reasonable credit risk(s), as determined by the holder based upon review of the debtor's...

17 CFR 240.14a-1 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-04-01

... a meeting, the earliest date they may be used to effect corporate action. (f) Proxy. The term “proxy... proxy; or (iii) The furnishing of a form of proxy or other communication to security holders under... proxy; or (iv) A communication by a security holder who does not otherwise engage in a proxy...

Should "Eudaimonia" Structure Professional Virtue?

ERIC Educational Resources Information Center

Eriksen, Andreas

2016-01-01

This article develops a "eudaimonistic" account of professional virtue. Using the case of teaching, the article argues that professional virtue requires that role holders care about the ends of their work. Care is understood in terms of an investment of the self. Virtuous role holders are invested in their practice in a way that makes…