Science.gov

Sample records for spectabilis dc irwin

  1. Cassia spectabilis DC seed galactomannan: structural, crystallographical and rheological studies.

    PubMed

    Kapoor, V P; Taravel, F R; Joseleau, J P; Milas, M; Chanzy, H; Rinaudo, M

    1998-01-01

    The seeds of Cassia spectabilis DC (family: Leguminoseae), an Indian fast growing spreading tree, contain about 40% of endosperm and possess the characteristics of becoming a potential source of commercial gum. The purified galactomannan shows Mw 1.1 x 10(6), intrinsic viscosity [eta] 615ml/g with k' = 1.706 x 10(-1), and a mannose to galactose ration of 2.65. The hydrolysis of the fully methylated polysaccharide reveals clearly the expected structure of legume galactomannans. The orthorhombic lattice constants of the hydrated gums are as follows: a = 9.12 A, b = 25.63 A and c = 10.28 A. The results of X-ray fiber studies show that the b dimension of the unit cell is very sensitive to relative humidity (RH), galactose substitution and orientation of the films. The probable space group symmetry of the unit cell is P2(1)2(1)2. Rheological studies of the galactomannan have shown that the transition from semi-dilute to dilute regime occurs at a critical concentration Cc* = 2.75. The slope of the log-log plot of specific viscosity versus C at zero shear rate is 5.87 in the more concentrated regime. The viscoelastic and critical shear rate behavior indicate the characteristics of a coil polymer. The large dependence of the viscosity on the coil overlap parameter is probably due to polymer-polymer interactions and peculiarity of the galactose distribution along the chain. Above 20 g/L concentration, the rheological behavior of the gum is like the one of a weak-gel.

  2. Profile of a Peace Historian: Irwin Abrams.

    ERIC Educational Resources Information Center

    OAH Magazine of History, 1994

    1994-01-01

    Discusses the significance of Irwin Abrams to the field of peace history. Describes Abrams' personal life, his work with the American Friends Service Committee, his scholarly work, and his leadership in peace history. Concludes by discussing his research on the Nobel Peace Prize and its recipients. (CFR)

  3. Ground-water hydrology and water quality of Irwin Basin at Fort Irwin National Training Center, California

    USGS Publications Warehouse

    Densmore, Jill N.; Londquist, Clark J.

    1997-01-01

    Geohydrologic data were collected from Irwin Basin at Fort Irwin National Training Center in the Mojave Desert of southern California by the U.S. Geological Survey during 199296 to deter mine the quantity and quality of ground water available in this basin. In addition to data collected from existing wells and test holes, 17 monitoring sites were constructed in Irwin Basin to provide data on subsurface geology, ground-water levels, and ground-water quality. Eleven of these sites were multiple-well monitoring sites that were constructed to provide depth-dependent geohydrologic data in the aquifer system. The aquifer system of Irwin Basin, defined on the basis of hydrologic data collected from wells in Irwin Basin, consists of an upper and a lower aquifer. A 1994 water-table contour map shows that a cone of depression beneath Irwin Basin well field has developed as a result of ground-water development. Water-quality samples collected from Irwin Basin wells to determine potential sources of ground-water degradation indicate that water in three areas in the basin contains high nitrate and dissolved-solids concentrations. The stable isotopes of oxygen and hydrogen indicate that present-day precipitation is not a major source of recharge in this basin. Tritium and carbon-14 data indicate that most of the basin was recharged before 1953 and that this water may be more than 14,000 years old.

  4. SPace Radar Image of Fort Irwin, California

    NASA Technical Reports Server (NTRS)

    1994-01-01

    This image of Fort Irwin in California's Mojave Desert compares interferometric radar signatures topography -- data that were obtained by multiple imaging of the same region to produce three-dimensional elevation maps -- as it was obtained on October 7-8, 1994 by the Spaceborne Imaging Radar-C/X-band Synthetic Aperture Radar aboard the space shuttle Endeavour. Data were acquired using the L-band (24 centimeter wavelength) and C-band (6 centimeter wavelength). The image covers an area about 25 kilometers by 70 kilometers (15.5 miles by 43 miles). North is to the lower right of the image. The color contours shown are proportional to the topographic elevation. With a wavelength one-fourth that of the L-band, the results from the C-band cycle through the color contours four times faster for a given elevation change. Detailed comparisons of these multiple frequency data over different terrain types will provide insights in the future into wavelength-dependent effects of penetration and scattering on the topography measurement accuracy. Fort Irwin is an ideal site for such detailed digital elevation model comparisons because a number of high precision digital models of the area already exist from conventional measurements as well as from airborne interferometric SAR data. Spaceborne Imaging Radar-C and X-band Synthetic Aperture Radar (SIR-C/X-SAR) is part of NASA's Mission to Planet Earth. The radars illuminate Earth with microwaves, allowing detailed observations at any time, regardless of weather or sunlight conditions. SIR-C/X-SAR uses three microwave wavelengths: L-band (24 cm), C-band (6 cm) and X-band (3 cm). The multi-frequency data will be used by the international scientific community to better understand the global environment and how it is changing. The SIR-C/X-SAR data, complemented by aircraft and ground studies, will give scientists clearer insights into those environmental changes which are caused by nature and those changes which are induced by human

  5. Irwin L. Goldstein (1937-2013).

    PubMed

    Schneider, Benjamin

    2014-01-01

    Irwin L. Goldstein-known as Irv by everyone-was born in New York City on October 4, 1937 and died on March 18, 2013. Irv loved ideas, especially good theoretical ideas that had practical applications. He was both a scholar and a practitioner of industrial psychology. At various times, he was associate editor of both the Journal of Applied Psychology and Human Factors, and his very influential book Training in Organizations (1974) went through four editions. The Society for Industrial and Organizational Psychology (SIOP) benefited enormously from his efforts on its behalf. If you chatted with Irv about any of his administrative positions, but especially about this last one, you would hear how much he felt, once again, that he was learning and how excited he was about what was actually possible in higher education. Irv retired from this position in 2012. In his many academic administrative roles, Irv was a mentor to all-graduate students, faculty, department chairs, and deans as well. Irv had had excellent role models to work from, and he cared for excellence and hard work-always with a twinkle in his eyes. PMID:24446842

  6. How will Mahanarva spectabilis (Hemiptera: Cercopidae) Respond to Global Warming?

    PubMed Central

    Auad, A. M.; Resende, T. T.; Hott, M. C.; Borges, C.A.V.

    2016-01-01

    The aim of this study was to determine the favorable constant temperature range for Mahanarva spectabilis (Distant) (Hemiptera: Cercopidae) development as well as to generate geographic distribution maps of this insect pest for future climate scenarios. M. spectabilis eggs were reared on two host plants (Brachiaria ruziziensis (Germain and Edvard) and Pennisetum purpureum (Schumach)), with individual plants kept at temperatures of 16, 20, 24, 28, and 32°C. Nymphal stage duration, nymphal survival, adult longevity, and egg production were recorded for each temperature*host plant combination. Using the favorable temperature ranges for M. spectabilis development, it was possible to generate geographic distribution. Nymphal survival was highest at 24.4°C, with estimates of 44 and 8% on Pennisetum and Brachiaria, respectively. Nymphal stage duration was greater on Brachiaria than on Pennisetum at 20 and 24°C but equal at 28°C. Egg production was higher on Pennisetum at 24 and 28°C than at 20°C, and adult longevity on Pennisetum was higher at 28°C than at 20°C, whereas adult longevity at 24°C did not differ from that at 20 and 28°C. With these results, it was possible to predict a reduction in M. spectabilis densities in most regions of Brazil in future climate scenarios. PMID:27012869

  7. How will Mahanarva spectabilis (Hemiptera: Cercopidae) Respond to Global Warming?

    PubMed

    Fonseca, M G; Auad, A M; Resende, T T; Hott, M C; Borges, C A V

    2016-01-01

    The aim of this study was to determine the favorable constant temperature range for Mahanarva spectabilis(Distant) (Hemiptera: Cercopidae) development as well as to generate geographic distribution maps of this insect pest for future climate scenarios. M. spectabilis eggs were reared on two host plants (Brachiaria ruziziensis(Germain and Edvard) and Pennisetum purpureum(Schumach)), with individual plants kept at temperatures of 16, 20, 24, 28, and 32 °C. Nymphal stage duration, nymphal survival, adult longevity, and egg production were recorded for each temperature*host plant combination. Using the favorable temperature ranges for M. spectabilis development, it was possible to generate geographic distribution. Nymphal survival was highest at 24.4 °C, with estimates of 44 and 8% on Pennisetum and Brachiaria, respectively. Nymphal stage duration was greater on Brachiaria than on Pennisetum at 20 and 24 °C but equal at 28 °C. Egg production was higher on Pennisetum at 24 and 28 °C than at 20 °C, and adult longevity on Pennisetum was higher at 28 °C than at 20 °C, whereas adult longevity at 24 °C did not differ from that at 20 and 28 °C. With these results, it was possible to predict a reduction in M. spectabilis densities in most regions of Brazil in future climate scenarios.

  8. The toxicity of Crotalaria spectabilis seed for quail

    USGS Publications Warehouse

    Nestler, R.B.; Bailey, W.W.

    1941-01-01

    Crotalaria as a cover crop is gaining attention in our country's conservation program. This genus of the legume or pulse family consists of more than 100 species. Of this number at least six are known to be very toxic to cattle, sheep, and horses. The seeds of Crotalaria spectabilis are poisonous to bob-whites. Under ordinary conditions, however, they are not eaten by the birds when there is a choice of feeding stuffs.

  9. Secondary metabolites from the stem of Ravenia spectabilis Lindl

    PubMed Central

    Haque, Md. Mozammel; Begum, Sufia; Sohrab, Md. Hossain; Ahsan, Monira; Hasan, Choudhury M.; Ahmed, Nuruddin; Haque, Rashedul

    2013-01-01

    Background: Ravenia spectabilis is a medium tall shrub found widespread in South America. It also found in India, Pakistan, Bangladesh etc. Few alkaloid and steroid compounds were reported from the plant previously. Materials and Methods: Methanol extract from the stems of Ravenia spectabilis were partitioned into n-hexane, carbon tetrachloride, chloroform and aqueous soluble fractions, respectively. The crude methanol extract, carbon tetrachloride fraction and chloroform fraction were fractionated by column chromatography of Silica gel and Sephadex LH-20 for isolation and purification of compounds. The structures of the isolated compounds were determined by extensive NMR spectral analysis, including 2D NMR, mass spectroscopy etc. Results: Ten compounds, γ-fagarine (1), ravenoline (2), N-methyl atanine (3),2,3,3,5-tetramethyl-2,3,4,5- tetrahydrofurano [3,2-c] quinolin-4-one (4), arborinine (5), 3-geranyl indole (6), atanine (7), steroids sitosta-4-en- 3-one (8), stigmasterol (9) and 3-methoxy-4-hydroxy cinnamic acid (10) were isolated from the stems of Ravenia spectabilis. Conclusion: Compounds N-methyl atanine (3), 2,3,3,5-tetramethyl-2,3,4,5-tetrahydrofurano [3,2-c] quinolin-4-one (4), 3-geranyl indole (6), sitosta-4-en-3-one (8) and 3-methoxy-4-hydroxy cinnamic acid (10) were isolated from this plant for the first time. 3-geranyl indole (6) was also isolated second time from natural sources. PMID:23661998

  10. Impact of the Spittlebug Mahanarva spectabilis on Signal Grass

    PubMed Central

    Resende, Tiago Teixeira; Auad, Alexander Machado; Fonseca, Marcy das Graças; dos Santos, Thiago Henrique; Vieira, Tamiris Moreira

    2012-01-01

    The aim of this study was to determine the damage in Brachiaria ruziziensis (Germain & Edvard) according to the density of and exposure time to adults of Mahanarva spectabilis (Distant, 1909) (Hemiptera:Cercopidae). Each plant was kept with 0, 12, 18, or 24 adults of M. spectabilis for five or ten days. Then, the insects were removed from the plant, and the following parameters were evaluated: content and loss of chlorophyll, visual damage score, shoot dry mass, and the capability for regrowth. In fact, plants exposed to the highest level of infestation for 10 days showed an 80.97% loss of chlorophyll, which is 25% higher than that shown by the plants exposed for five days. The damage score also increased with infestation levels. In the levels of 12 and 18 adults per plant, the damage score increased with increasing time of exposure. The dry mass content was higher in plants exposed to 24 insects for 10 days, suggesting that the attack of spittlebugs caused premature drying of the plant. These effects caused significant reduction in the number of tillers of infested plants. Our results indicate that exposure to adults of M. spectabilis causes significant damage and affects the development and persistence of B. ruziziensis plants. PMID:22927790

  11. Fort Irwin Integrated Resource Assessment. Volume 2, Baseline detail

    SciTech Connect

    Richman, E.E.; Keller, J.M.; Dittmer, A.L.; Hadley, D.L.

    1994-01-01

    This report documents the assessment of baseline energy use at Fort Irwin, a US Army Forces Command facility near Barstow, California. It is a companion report to Volume 1, Executive Summary, and Volume 3, Integrated Resource Assessment. The US Army Forces Command (FORSCOM) has tasked the US Department of Energy (DOE) Federal Energy Management Program (FEMP), supported by the Pacific Northwest Laboratory (PNL), to identify, evaluate, and assist in acquiring all cost-effective energy projects at Fort Irwin. This is part of a model program that PNL has designed to support energy-use decisions in the federal sector. This program (1) identifies and evaluates all cost-effective energy projects; (2) develops a schedule at each installation for project acquisition considering project type, size, timing, and capital requirements, as well as energy and dollar savings; and (3) targets 100% of the financing required to implement energy efficiency projects. PNL applied this model program to Fort Irwin. This analysis examines the characteristics of electric, propane gas, and vehicle fuel use for a typical operating year. It records energy-use intensities for the facilities at Fort Irwin by building type and energy end use. It also breaks down building energy consumption by fuel type, energy end use, and building type. A complete energy consumption reconciliation is presented that accounts for all energy use among buildings, utilities, and applicable losses.

  12. Simulation of Ground-Water Flow in the Irwin Basin Aquifer System, Fort Irwin National Training Center, California

    USGS Publications Warehouse

    Densmore, Jill N.

    2003-01-01

    Ground-water pumping in the Irwin Basin at Fort Irwin National Training Center, California resulted in water-level declines of about 30 feet from 1941 to 1996. Since 1992, artificial recharge from wastewater-effluent infiltration and irrigation-return flow has stabilized water levels, but there is concern that future water demands associated with expansion of the base may cause a resumption of water-level declines. To address these concerns, a ground-water flow model of the Irwin Basin was developed to help better understand the aquifer system, assess the long-term availability and quality of ground water, and evaluate ground-water conditions owing to current pumping and to plan for future water needs at the base. Historical data show that ground-water-level declines in the Irwin Basin between 1941 and 1996, caused the formation of a pumping depression near the pumped wells, and that recharge from the wastewater-treatment facility and disposal area caused the formation of a recharge mound. There have been two periods of water-level recovery in the Irwin Basin since the development of ground water in this basin; these periods coincide with a period of decreased pumpage from the basin and a period of increased recharge of water imported from the Bicycle Basin beginning in 1967 and from the Langford Basin beginning in 1992. Since 1992, artificial recharge has exceeded pumpage in the Irwin Basin and has stabilized water-level declines. A two-layer ground-water flow model was developed to help better understand the aquifer system, assess the long-term availability and quality of ground water, and evaluate ground-water conditions owing to current pumping and to plan for future water needs at the base. Boundary conditions, hydraulic conductivity, altitude of the bottom of the layers, vertical conductance, storage coefficient, recharge, and discharge were determined using existing geohydrologic data. Rates and distribution of recharge and discharge were determined from

  13. Health evaluation of western arctic King Eiders (Somateria spectabilis)

    USGS Publications Warehouse

    Scott, Cheryl A.; Mazet, Jonna A.K.; Powell, Abby N.

    2010-01-01

    The western arctic population of King Eiders (Somateria spectabilis) has declined by >50% in recent years. A health assessment was conducted for adult King Eiders breeding on the north slope of Alaska, USA, to evaluate body condition (n=90, 2002–2006) and baseline biochemical and hematologic values (n=20–30, 2005–2006). Body condition for males and females was excellent. Total protein, calcium, alkaline phosphatase, amylase, and globulin were significantly higher in females than in males, likely because of differences in reproductive physiology. These baseline health data can be used to promote conservation of King Eiders and other closely related species of concern.

  14. Seismic communication between the burrows of kangaroo rats, Dipodomys spectabilis.

    PubMed

    Randall, J A; Lewis, E R

    1997-11-01

    Banner-tailed kangaroo rats, Dipodomys spectabilis, footdrum to produce substrate-borne and airborne acoustic energy. Previous studies show that they communicate territorial ownership via airborne footdrumming signals. The research reported here used simulated footdrum patterns generated by an artificial 'thumper' to address the question of whether kangaroo rats communicate through seismic components of these acoustic signals. With microphones suspended in sealed burrows, we found that airborne sounds were attenuated by approximately 40 dB as they passed through the burrow wall into the burrow chamber. The substrate-borne vibrations from the thumper yielded sound approximately 40 dB greater in peak amplitude than the attenuated airborne sound. Thus, 99.9% of the peak power of the thumper was transmitted directly through the substrate into the burrow. The rats in sealed burrows timed their responses to playbacks of footdrums from the thumper and a loudspeaker so they did not initiate a drumming sequence during either the seismic or airborne signals. When these signals were masked by loud noise, the rats continued to drum to the seismic signal but drummed randomly during the airborne playback. These results suggest that the sealed burrow provides a quiet place in which D. spectabilis can listen for substrate-borne communications from conspecifics.

  15. Microsatellite markers for Senna spectabilis var. excelsa (Caesalpinioideae, Fabaceae)1

    PubMed Central

    López-Roberts, M. Cristina; Barbosa, Ariane R.; Paganucci de Queiroz, Luciano; van den Berg, Cássio

    2016-01-01

    Premise of the study: Senna spectabilis var. excelsa (Fabaceae) is a South and Central American tree of great ecological importance and one of the most common species in several sites of seasonally dry forests. Our goal was to develop microsatellite markers to assess the genetic diversity and structure of this species. Methods and Results: We designed and assessed 53 loci obtained from a microsatellite-enriched library and an intersimple sequence repeat library. Fourteen loci were polymorphic, and they presented a total of 39 alleles in a sample of 61 individuals from six populations. The mean values of observed and expected heterozygosities were 0.355 and 0.479, respectively. Polymorphism information content was 0.390 and the Shannon index was 0.778. Conclusions: Polymorphism information content and Shannon index indicate that at least nine of the 14 microsatellite loci developed are moderate to highly informative, and potentially useful for population genetic studies in this species. PMID:26819856

  16. Primula spectabilis Tratt. aerial parts: morphology, volatile compounds and flavonoids.

    PubMed

    Vitalini, Sara; Flamini, Guido; Valaguzza, Aurora; Rodondi, Graziella; Iriti, Marcello; Fico, Gelsomina

    2011-08-01

    The vacuolar and epicuticular flavonoids and the volatiles of the leaves and parts of flower of P. spectabilis Tratt., an endemic species in the Italian Oriental Alps, were investigated. From a MeOH extract of the leaves two flavone glycosides, 8-C-β-glucopyranosylluteolin 7-O-α-arabinofuranoside (1) and 6-C-α-arabinofuranosylapigenin (2) were isolated, in addition to a flavone and three flavonols already known from species of Primula. From an EtOH extract of leaf exudates, 7,3',4'-tri-O-methylquercetin was obtained. The structures were elucidated on the basis of their 1D ¹H- and ¹³C NMR data and 2D NMR techniques, as well as of HPLC-MS. The volatiles emitted by the leaves were mainly constituted by non-terpene derivatives, followed by comparable proportions of hemiterpens, oxygenated monoterpenes and sesquiterpene hydrocarbons. In flowers, monoterpene hydrocarbons were the most represented chemical class followed by non-terpene derivatives. Different proportions of compounds were found when individual parts of flowers were examined separately; calyx produced a greater proportion (approx. 49.5%) of non-terpenes as its volatile metabolites. P. spectabilis has glandular trichomes in the hyaline margins of the epidermal depressions, distributed on the adaxial leaf blade. Glandular hairs were also present on the corolla. Correlations of phytochemical data with the morphological features of leaf, flower and glandular hair are discussed, and a hypothesis is proposed on the ecological roles of the flavonoids and volatile compounds on the general fitness of the species and cross-pollination strategies.

  17. Standardization of Cassia spectabilis with respect to authenticity, assay and chemical constituent analysis.

    PubMed

    Torey, Angeline; Sasidharan, Sreenivasan; Yeng, Chen; Latha, Lachimanan Yoga

    2010-05-01

    Quality control standardizations of the various medicinal plants used in traditional medicine is becoming more important today in view of the commercialization of formulations based on these plants. An attempt at standardization of Cassia spectabilis leaf has been carried out with respect to authenticity, assay and chemical constituent analysis. The authentication involved many parameters, including gross morphology, microscopy of the leaves and functional group analysis by Fourier Transform Infrared (FTIR) spectroscopy. The assay part of standardization involved determination of the minimum inhibitory concentration (MIC) of the extract which could help assess the chemical effects and establish curative values. The MIC of the C. spectabilis leaf extracts was investigated using the Broth Dilution Method. The extracts showed a MIC value of 6.25 mg/mL, independent of the extraction time. The chemical constituent aspect of standardization involves quantification of the main chemical components in C. spectabilis. The GCMS method used for quantification of 2,4-(1H,3H)-pyrimidinedione in the extract was rapid, accurate, precise, linear (R(2) = 0.8685), rugged and robust. Hence this method was suitable for quantification of this component in C. spectabilis. The standardization of C. spectabilis is needed to facilitate marketing of medicinal plants, with a view to promoting the export of valuable Malaysian Traditional Medicinal plants such as C. spectabilis.

  18. National Training Center Fort Irwin expansion area aquatic resources survey

    SciTech Connect

    Cushing, C.E.; Mueller, R.P.

    1996-02-01

    Biologists from Pacific Northwest National Laboratory (PNNL) were requested by personnel from Fort Irwin to conduct a biological reconnaissance of the Avawatz Mountains northeast of Fort Irwin, an area for proposed expansion of the Fort. Surveys of vegetation, small mammals, birds, reptiles, amphibians, and aquatic resources were conducted during 1995 to characterize the populations and habitats present with emphasis on determining the presence of any species of special concern. This report presents a description of the sites sampled, a list of the organisms found and identified, and a discussion of relative abundance. Taxonomic identifications were done to the lowest level possible commensurate with determining the status of the taxa relative to its possible listing as a threatened, endangered, or candidate species. Consultation with taxonomic experts was undertaken for the Coleoptera ahd Hemiptera. In addition to listing the macroinvertebrates found, the authors also present a discussion related to the possible presence of any threatened or endangered species or species of concern found in Sheep Creek Springs, Tin Cabin Springs, and the Amargosa River.

  19. Applications of band ratioing at Fort Irwin, California

    NASA Astrophysics Data System (ADS)

    Taylor, Alexander Wright

    This dissertation describes the results of two projects that demonstrate the power of band ratioing of remote sensing data. The first method, Band Ratio Differencing (BRD), challenges the more traditional techniques for detecting environmental disturbance of the surface in and terrains. These traditional techniques are inadequate because they cannot identify the nature of the change (physical, chemical, biological) or the processes (natural, anthropogenic) involved in causing the change. In contrast, BRD of Landsat TM data has the advantage of providing information about changes in the composition of alluvial surfaces. These compositional changes, when combined with empirical field data provides insight into the specific causes and effects of environmental change. BRD was applied at Fort Irwin, California, the U.S. Army's National Training Center (NTC) for desert warfare. Two dates of Landsat TM imagery (1985 and 1995) were acquired and BRD applied. A total of 514.5 square kilometers, or 42% of the alluvial surface at Fort Irwin has been affected by off road vehicular traffic. Two major types of change were identified: Disturbed Alluvial Surface and Continuous Dust Mantle, which can be further subdivided into six separate classes of change, related to either the cause or the effect of the disturbance. Hyperspectral Assisted Mapping (HAM) was developed as an alternative to Spectral Signature Mapping (SSM) techniques typically applied to AVIRIS hyperspectral data. Our analysis suggests that SSM-based techniques when applied to AVIRIS provide little to no additional information about sedimentary and igneous rocks. This is because many rock forming minerals of sedimentary and igneous rocks possess little to no diagnostic spectral absorption features in the range measured by the AVIRIS sensor. The HAM method integrates the geornorphic information provided by a Digital Elevation Model (DEM) and the lithologic discrimination, but not identification, provided by

  20. The Damage Capacity of Mahanarva spectabilis (Distant, 1909) (Hemiptera: Cercopidae) Adults on Brachiaria ruziziensis Pasture

    PubMed Central

    Resende, Tiago Teixeira; Auad, Alexander Machado; Fonseca, Marcy das Graças; Souza Sobrinho, Fausto; Ribeiro dos Santos, Dayane; da Silva, Sandra Elisa Barbosa

    2013-01-01

    The aim of this study was to determine the damage caused by adult Mahanarva spectabilis (Distant, 1909) (Hemiptera: Cercopidae) on Brachiaria ruziziensis (Germain & Evard) under field conditions. A total of 0, 4, 8, 12, or 16 M. spectabilis adults per plot were maintained for 6 days. Thereafter, the insects were removed from the plant, and the following parameters were evaluated: chlorophyll content, damage score, dry as well as fresh weights, percentage of shoots' dry matter, and the forage's ability to regrow. The chlorophyll content was significantly reduced; the damage score and percentage of dry matter in plants increased depending on the increased insect infestation density after 6 days of exposure. In contrast, no change was observed on the B. ruziziensis fresh and dry weights as well as the regrowth capacity depending on the M. spectabilis infestation densities. Attacks by 8 adult M. spectabilis per clump of B. ruziziensis with an average of 80 tillers for 6 days were sufficient to reduce the chlorophyll content and the functional plant loss index. This density can be a reference for spittlebug integrated management in Brachiaria. PMID:24453825

  1. Airborne electromagnetic data and processing within Leach Lake Basin, Fort Irwin, California: Chapter G in Geology and geophysics applied to groundwater hydrology at Fort Irwin, California

    USGS Publications Warehouse

    Bedrosian, Paul A.; Ball, Lyndsay B.; Bloss, Benjamin R.

    2014-01-01

    From December 2010 to January 2011, the U.S. Geological Survey conducted airborne electromagnetic and magnetic surveys of Leach Lake Basin within the National Training Center, Fort Irwin, California. These data were collected to characterize the subsurface and provide information needed to understand and manage groundwater resources within Fort Irwin. A resistivity stratigraphy was developed using ground-based time-domain electromagnetic soundings together with laboratory resistivity measurements on hand samples and borehole geophysical logs from nearby basins. This report releases data associated with the airborne surveys, as well as resistivity cross-sections and depth slices derived from inversion of the airborne electromagnetic data. The resulting resistivity models confirm and add to the geologic framework, constrain the hydrostratigraphy and the depth to basement, and reveal the distribution of faults and folds within the basin.

  2. Introduction to the geologic and geophysical studies of Fort Irwin, California: Chapter A in Geology and geophysics applied to groundwater hydrology at Fort Irwin, California

    USGS Publications Warehouse

    Buesch, David C.

    2014-01-01

    Geologic and geophysical investigations in the vicinity of Fort Irwin National Training Center, California, have been completed in support of groundwater investigations, and are presented in eight chapters of this report. A generalized surficial geologic map along with field and borehole investigations conducted during 2010–11 provide a lithostratigraphic and structural framework for the area during the Cenozoic. Electromagnetic properties of resistivity were measured in the laboratory on hand and core samples, and compared to borehole geophysical resistivity data. These data were used in conjunction with ground-based time-domain and airborne data and interpretations to provide a framework for the shallow lithologic units and structure. Gravity and aeromagnetic maps cover areas ~4 to 5 times that of Fort Irwin. Each chapter includes hydrogeologic applications of the data or model results.

  3. Brownian motion, old and new, and Irwin's role in my academic life

    NASA Astrophysics Data System (ADS)

    Lindenberg, Katja

    2015-03-01

    Irwin Oppenheim's early work on Langevin equations, master equations, and Brownian motion was one of the earliest and strongest reasons for my change of direction from my PhD work in condensed matter theory to my later and lifelong interest in Brownian motion and, more broadly, statistical mechanics. I will talk about some of my most recent work on subdiffusion, a form of anomalous diffusion that describes random motions in crowded or disordered media where motions are hindered by the medium. On a personal note, I knew Irwin for decades, from the time before he had a family (he was a sworn bachelor...until he met his wife) until shortly before his death. For many years, first alone and then with family, Irwin would spend some portion of the cold Boston winter in warm La Jolla, and we would always get together during these visits. For a period of a number of years we decided to take advantage of these visits to write the definitive text in traditional Thermodynamics. We did not make it past about 2/3 of the project, but it was a great learning experience for me while it lasted. Irwin's knowledge and understanding of the subject were breathtaking.

  4. Aeromagnetic data, processing, and maps of Fort Irwin and vicinity, California: Chapter I in Geology and geophysics applied to groundwater hydrology at Fort Irwin, California

    USGS Publications Warehouse

    Langenheim, V.E.; Jachens, Robert C.; Buesch, David C.

    2014-01-01

    Aeromagnetic data help provide the underpinnings of a hydrogeologic framework for Fort Irwin by locating inferred structural features or grain that influence groundwater flow. Magnetization boundaries defined by horizontal-gradient analyses coincide locally with Cenozoic faults and can be used to extend these faults beneath cover. These boundaries also highlight the structural grain within the crystalline rocks and may serve as a proxy for fracturing, an important source of permeability within the generally impermeable basement rocks, thus mapping potential groundwater pathways through and along the mountain ranges in the study area.

  5. Brachiaria ruziziensis Responses to Different Fertilization Doses and to the Attack of Mahanarva spectabilis (Hemiptera: Cercopidae) Nymphs and Adults

    PubMed Central

    Aguiar, Daniela de Melo; Auad, Alexander Machado; Fonseca, Marcy das Graças; Leite, Melissa Vieira

    2014-01-01

    Cropping practices are necessary in order to help reduce the population of pest insect, such as the induction of resistance through fertilization. Therefore, this study aimed to assess alterations on the production and quality of Brachiaria ruziziensis when receiving the fertilization composed by the macronutrients NPK and/or exposed to the attack of Mahanarva spectabilis nymphs and adults. B. ruziziensis plants were fertilized according to the recommendation (R), half of the recommended fertilization (H), or non-fertilization (C). They were also exposed to different M. spectabilis nymph and adult densities. The damage, regrowth, and bromatological components were evaluated. The fertilization treatment promoted a higher M. spectabilis nymph survival on B. ruziziensis; however, it reduced the damage caused by the forage exposed to nymphs and adults of pest insect, and it did not alter the quality of the signal grass. Moreover, the fertilization treatment enabled forage recovery, even when exposed to 5 nymphs or 10 spittlebug adults. PMID:24578645

  6. Bernard John Dowling Irwin and the development of the field hospital at Shiloh.

    PubMed

    Fahey, John H

    2006-05-01

    The field hospital remains a centerpiece of casualty care evacuation systems, dating back to the Civil War. Dr. Bernard John Dowling Irwin is credited with establishing the first tent field hospital during the battle of Shiloh. However, controversy regarding this claim exists because of the confusing practice of using the term "field hospital" to refer to facilities with different capabilities. By examining the specific levels of care available on the battlefield, I review the evolution of the different types of field hospitals, focusing on the increasingly complex capabilities that evolved in the spring of 1862 in the Western Theater. I conclude that Irwin's hospital was the first practical demonstration that sufficient inpatient care could be provided on the battlefield, eliminating the need to evacuate unstable patients. PMID:16761879

  7. Energy saving potential of residential HVAC options at Fort Irwin, California

    SciTech Connect

    Hadley, D.L.; Stucky, D.J.

    1995-03-01

    The Pacific Northwest Laboratory (PNL) evaluated heating and cooling system options for existing family housing at Fort Irwin, California. The purpose of this work was to quantify the energy conservation potential of alternative system types and to identify the most cost-effective technology available. The conventional residential heating/cooling systems at Fort Irwin are separate propane forced-air furnaces and central air conditioners. The options examined included air- and ground-source heat pumps, a natural gas furnace with central air conditioning, and a natural-gas-fired heat pump. The most cost-effective technology applicable to Fort Irwin was found to be the high-efficiency ground-source heat pumps. If all conventional units were replaced immediately, the net energy savings would be 76,660 MBtu (80.9 TJ) per year and a reduction in electrical demand of approximately 15,000 kW-month. The initial investment for implementing this technology would be approximately $7.1 million, with a savings-to-investment ratio of 1.74.

  8. Gravity survey and interpretation of Fort Irwin and vicinity, Mojave Desert, California: Chapter H in Geology and geophysics applied to groundwater hydrology at Fort Irwin, California

    USGS Publications Warehouse

    Jachens, Robert C.; Langenheim, V.E.; Buesch, David C.

    2014-01-01

    In support of a hydrogeologic study of the groundwater resources on Fort Irwin, we have combined new gravity data with preexisting measurements to produce an isostatic residual gravity map, which we then separated into two components reflecting (1) the density distribution in the pre-Cenozoic basement complex and (2) the distribution of low-density Cenozoic volcanic and sedimentary deposits that lie on top of the basement complex. The second component was inverted to estimate the three-dimensional distribution of Cenozoic deposits by using constraints from geology, drillholes, and time-domain electromagnetic soundings. In most of the base, the Cenozoic deposits are no more than 300 m thick, except in the basins with more than 500 m of fill beneath Coyote Lake, Red Pass Lake, west of Nelson Lake, west of Superior Lake, Bicycle Lake, and in the vicinity of Nelson Lake.

  9. Chi-squared and Fisher-Irwin tests of two-by-two tables with small sample recommendations.

    PubMed

    Campbell, Ian

    2007-08-30

    Two-by-two tables commonly arise in comparative trials and cross-sectional studies. In medical studies, two-by-two tables may have a small sample size due to the rarity of a condition, or to limited resources. Current recommendations on the appropriate statistical test mostly specify the chi-squared test for tables where the minimum expected number is at least 5 (following Fisher and Cochran), and otherwise the Fisher-Irwin test; but there is disagreement on which versions of the chi-squared and Fisher-Irwin tests should be used. A further uncertainty is that, according to Cochran, the number 5 was chosen arbitrarily. Computer-intensive techniques were used in this study to compare seven two-sided tests of two-by-two tables in terms of their Type I errors. The tests were K. Pearson's and Yates's chi-squared tests and the 'N-1' chi-squared test (first proposed by E. Pearson), together with four versions of the Fisher-Irwin test (including two mid-P versions). The optimum test policy was found to be analysis by the 'N-1' chi-squared test when the minimum expected number is at least 1, and otherwise, by the Fisher-Irwin test by Irwin's rule (taking the total probability of tables in either tail that are as likely as, or less likely than the one observed). This policy was found to have increased power compared to Cochran's recommendations. PMID:17315184

  10. Generalized surficial geologic map of the Fort Irwin area, San Bernadino: Chapter B in Geology and geophysics applied to groundwater hydrology at Fort Irwin, California

    USGS Publications Warehouse

    Miller, David M.; Menges, Christopher M.; Lidke, David J.; Buesch, David C.

    2014-01-01

    The geology and landscape of the Fort Irwin area, typical of many parts of the Mojave Desert, consist of rugged mountains separated by broad alluviated valleys that form the main coarse-resolution features of the geologic map. Crystalline and sedimentary rocks, Mesozoic and older in age, form most of the mountains with lesser accumulations of Miocene sedimentary and volcanic rocks. In detail, the area exhibits a fairly complex distribution of surficial deposits resulting from diverse rock sources and geomorphology that has been driven by topographic changes caused by recent and active faulting. Depositional environments span those typical of the Mojave Desert: alluvial fans on broad piedmonts, major intermittent streams along valley floors, eolian sand dunes and sheets, and playas in closed valleys that lack through-going washes. Erosional environments include rocky mountains, smooth gently sloping pediments, and badlands in readily eroded sediment. All parts of the landscape, from regional distribution of mountains, valleys, and faults to details of degree of soil development in surface materials, are portrayed by the surficial geologic map. Many of these attributes govern infiltration and recharge, and the surface distribution of permeable rock units such as Miocene sedimentary and volcanic rocks provides a basis for evaluating potential groundwater storage. Quaternary faults are widespread in the Fort Irwin area and include sinistral, east-striking faults that characterize the central swath of the area and the contrasting dextral, northwest-striking faults that border the east and west margins. Bedrock distribution and thickness of valley-fill deposits are controlled by modern and past faulting, and faults on the map help to identify targets for groundwater exploration.

  11. Leishmanicidal activity of the crude extract, fractions and major piperidine alkaloids from the flowers of Senna spectabilis.

    PubMed

    de Albuquerque Melo, Gabriela Muniz; Silva, Marcela Campelo Rodrigues; Guimarães, Thaís Pereira; Pinheiro, Kátia Mantovani; da Matta, Carolina Barbosa Brito; de Queiroz, Aline Cavalcanti; Pivatto, Marcos; Bolzani, Vanderlan da Silva; Alexandre-Moreira, Magna Suzana; Viegas, Claudio

    2014-02-15

    Senna spectabilis (sin. Cassia excelsa, C. spectabilis) is an endemic tree of South America and Africa, very common in Brazil, where it is known as "canafistula-de-besouro" and "cassia-do-nordeste". In folk medicine, this plant is indicated for the treatment of constipation, insomnia, anxiety, epilepsy, malaria, dysentery and headache. Phytopharmacological studies have also confirmed anticonvulsive, sedative, anti-malarial, antimicrobial and cytotoxic properties of many parts of S. spectabilis. In this communication, we present a comparative study of the leishmanicidal activity of the crude ethanolic extract, its fractions and also the two major alkaloidal metabolites (-)-cassine/(-)-spectaline, trying to establish a relationship between the presence of piperidine alkaloidal constituents and leishmanicidal activity. The growth inhibitory effect of promastigote forms of Leishmania major was determined for the crude extract, fractions of the flowers of S. spectabilis and a mixture of (-)-cassine/(-)-spectaline in comparison to pentamidine used as standard drug. The cytotoxic effects were assessed on macrophage strain J774 by lactate dehydrogenase assay. Fractions dichloromethane (FL-DCM) and n-butanol (FL-Bu) and a mixture of (-)-cassine/(-)-spectaline (∼7:3) exhibited significant activity against the parasite Leishmania major (IC50 values of 0.6±0.1 μg/ml, 1.6±0.9 μg/ml and 24.9±1.4 μg/ml, respectively), without toxic effects on murine macrophages. Due to the promising results elicited, further studies in vivo need to be performed to confirm the therapeutic potential of Senna spectabilis.

  12. Lipoperoxidation and cyclooxygenase enzyme inhibitory piperidine alkaloids from Cassia spectabilis green fruits.

    PubMed

    Viegas, Cláudio; Silva, Dulce H S; Pivatto, Marcos; de Rezende, Amanda; Castro-Gambôa, Ian; Bolzani, Vanderlan S; Nair, Muraleedharan G

    2007-12-01

    Phytochemical work in the search for bioactive metabolites from the methanolic extract of Senna spectabilis green fruits led to the isolation of a new piperidine alkaloid, (+)-3- O-feruloylcassine ( 1), in addition to the known (-)-spectaline ( 2) and (-)-3- O-acetylspectaline ( 3). The isolates were submitted to in vitro evaluation of lipoperoxidation (LPO) and cyclooxygenase enzymes (COX-1 and -2) inhibitory properties and showed moderate antioxidant activities (40-70%) at 100 ppm when compared to commercial standards BHT and vitamin E and moderate inhibition of COX-1 (ca . 40%) and marginal inhibition of COX-2 enzymes (<10%) at 100 ppm when compared to nonsteroidal anti-inflammatory drugs (NSAIDs) aspirin, rofecoxib, and celecoxib, respectively. PMID:18047293

  13. Fort Irwin integrated resource assessment. Volume 3: Sitewide Energy Project identification for buildings and facilities

    SciTech Connect

    Keller, J.M.; Dittmer, A.L.; Elliott, D.B.; McMordie, K.L.; Richman, E.E.; Stucky, D.J.; Wahlstrom, R.R.; Hadley, D.L.

    1995-02-01

    The U.S. Army Forces Command (FORSCOM) has tasked the U.S. Department of Energy (DOE) Federal Energy Management Program (FEMP), supported by the Pacific Northwest Laboratory, to identify, evaluate, and assist in acquiring all cost-effective energy projects at Fort Irwin. This is part of a model program that PNL is designing to support energy-use decisions in the federal sector. This report provides the results of the fossil fuel and electric energy resource opportunity (ERO) assessments performed by PNL at the FORSCOM Fort Irwin facility located near Barstow, California. It is a companion report to Volume 1, Executive Summary, and Volume 2, Baseline Detail. The results of the analyses of EROs are presented in 16 common energy end-use categories (e.g., boilers and furnaces, service hot water, and building lighting). A narrative description of each ERO is provided, along with a table detailing information on the installed cost, energy and dollar savings; impacts on operations and maintenance (O&M); and, when applicable, a discussion of energy supply and demand, energy security, and environmental issues. A description of the evaluation methodologies and technical and cost assumptions is also provided for each ERO. Summary tables present the cost-effectiveness of energy end-use equipment before and after the implementation of each ERO and present the results of the life-cycle cost (LCC) analysis indicating the net present valve (NPV) and savings-to-investment ratio (SIR) of each ERO.

  14. CNS Adverse Effects: From Functional Observation Battery/Irwin Tests to Electrophysiology.

    PubMed

    Fonck, Carlos; Easter, Alison; Pietras, Mark R; Bialecki, Russell A

    2015-01-01

    This chapter describes various approaches for the preclinical assessment of drug-induced central nervous system (CNS) adverse effects. Traditionally, methods to evaluate CNS effects have consisted of observing and scoring behavioral responses of animals after drug is administered. Among several behavioral testing paradigms, the Irwin and the functional observational battery (FOB) are the most commonly used assays for the assessment of CNS effects. The Irwin and FOB are considered good first-tier assays to satisfy the ICH S7A guidance for the preclinical evaluation of new chemical entities (NCE) intended for humans. However, experts have expressed concern about the subjectivity and lack of quantitation that is derived from behavioral testing. More importantly, it is difficult to gain insight into potential mechanisms of toxicity by assessing behavioral outcomes. As a complement to behavioral testing, we propose using electrophysiology-based assays, both in vivo and in vitro, such as electroencephalograms and brain slice field-potential recordings. To better illustrate these approaches, we discuss the implementation of electrophysiology-based techniques in drug-induced assessment of seizure risk, sleep disruption, and cognitive impairment.

  15. 78 FR 56978 - In the Matter of Carbiz, Inc., InZon Corporation, IQ Micro, Inc., Irwin Financial Corporation...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-09-16

    ... From the Federal Register Online via the Government Publishing Office SECURITIES AND EXCHANGE COMMISSION In the Matter of Carbiz, Inc., InZon Corporation, IQ Micro, Inc., Irwin Financial Corporation, and... lack of current and accurate information concerning the securities of IQ Micro, Inc. because it has...

  16. Laboratory electrical resistivity analysis of geologic samples from Fort Irwin, California: Chapter E in Geology and geophysics applied to groundwater hydrology at Fort Irwin, California

    USGS Publications Warehouse

    Bloss, Benjamin R.; Bedrosian, Paul A.

    2015-01-01

    Correlating laboratory resistivity measurements with geophysical resistivity models helps constrain these models to the geology and lithology of an area. Throughout the Fort Irwin National Training Center area, 111 samples from both cored boreholes and surface outcrops were collected and processed for laboratory measurements. These samples represent various lithologic types that include plutonic and metamorphic (basement) rocks, lava flows, consolidated sedimentary rocks, and unconsolidated sedimentary deposits that formed in a series of intermountain basins. Basement rocks, lava flows, and some lithified tuffs are generally resistive (≥100 ohm-meters [Ω·m]) when saturated. Saturated unconsolidated samples are moderately conductive to conductive, with resistivities generally less than 100 Ω·m, and many of these samples are less than 50 Ω·m. The unconsolidated samples can further be separated into two broad groups: (1) younger sediments that are moderately conductive, owing to their limited clay content, and (2) older, more conductive sediments with a higher clay content that reflects substantial amounts of originally glassy volcanic ash subsequently altered to clay. The older sediments are believed to be Tertiary. Time-domain electromagnetic (TEM) data were acquired near most of the boreholes, and, on the whole, close agreements between laboratory measurements and resistivity models were found. 

  17. Consequences of volcanic ash deposition on the locomotor performance of the Phymaturus spectabilis lizard from Patagonia, Argentina.

    PubMed

    Cabezas-Cartes, Facundo; Kubisch, Erika Leticia; Ibargüengoytía, Nora Ruth

    2014-03-01

    The locomotor performance of lizards depends on their morphological and physiological adaptations to the habitat. However, when the habitat changes dramatically, for example, by a volcanic eruption, the performance of lizards may be affected. We registered the vegetation cover, the surface covered by ash, the presence of crevices suitable for Phymaturus and the rocks slopes to analyze the effects of ash accumulation produced by the eruption of Puyehue-Cordon Caulle volcanic complex on microhabitat use and availability of the Phymaturus spectabilis lizard. In addition, we studied the effect of ashes and slope on the locomotor performance of P. spectabilis by registering the maximum speed in sprint runs and long runs under four different treatments (cork and on the level, ashes and on the level, cork and slope, and ashes and slope). P. spectabilis selected microhabitats unvegetated, with crevices and steep slopes. Regarding locomotor performance, the speed of lizards was negatively affected by the presence of ash only in sprint runs on the level and in long runs with slope. The slope had a negative impact on the speed in all the treatments. These results show that the presence of volcanic ashes in the substrate might have affected the locomotor performance of the lizards, especially in long runs, and hence, the interaction of individuals with the environment, that is, escaping from predators and social behavior.

  18. Consequences of volcanic ash deposition on the locomotor performance of the Phymaturus spectabilis lizard from Patagonia, Argentina.

    PubMed

    Cabezas-Cartes, Facundo; Kubisch, Erika Leticia; Ibargüengoytía, Nora Ruth

    2014-03-01

    The locomotor performance of lizards depends on their morphological and physiological adaptations to the habitat. However, when the habitat changes dramatically, for example, by a volcanic eruption, the performance of lizards may be affected. We registered the vegetation cover, the surface covered by ash, the presence of crevices suitable for Phymaturus and the rocks slopes to analyze the effects of ash accumulation produced by the eruption of Puyehue-Cordon Caulle volcanic complex on microhabitat use and availability of the Phymaturus spectabilis lizard. In addition, we studied the effect of ashes and slope on the locomotor performance of P. spectabilis by registering the maximum speed in sprint runs and long runs under four different treatments (cork and on the level, ashes and on the level, cork and slope, and ashes and slope). P. spectabilis selected microhabitats unvegetated, with crevices and steep slopes. Regarding locomotor performance, the speed of lizards was negatively affected by the presence of ash only in sprint runs on the level and in long runs with slope. The slope had a negative impact on the speed in all the treatments. These results show that the presence of volcanic ashes in the substrate might have affected the locomotor performance of the lizards, especially in long runs, and hence, the interaction of individuals with the environment, that is, escaping from predators and social behavior. PMID:24273207

  19. Microsatellite analyses across three diverse vertebrate transcriptomes (Acipenser fulvescens, Ambystoma tigrinum, and Dipodomys spectabilis).

    PubMed

    Doyle, Jacqueline M; Siegmund, Gregor; Ruhl, Joseph D; Eo, Soo Hyung; Hale, Matthew C; Marra, Nicholas J; Waser, Peter M; Dewoody, J Andrew

    2013-07-01

    Historically, many population genetics studies have utilized microsatellite markers sampled at random from the genome and presumed to be selectively neutral. Recent studies, however, have shown that microsatellites can occur in transcribed regions, where they are more likely to be under selection. In this study, we mined microsatellites from transcriptomes generated by 454-pyrosequencing for three vertebrate species: lake sturgeon (Acipenser fulvescens), tiger salamander (Ambystoma tigrinum), and kangaroo rat (Dipodomys spectabilis). We evaluated (i) the occurrence of microsatellites across species; (ii) whether particular gene ontology terms were over-represented in genes that contained microsatellites; (iii) whether repeat motifs were located in untranslated regions or coding sequences of genes; and (iv) in silico polymorphism. Microsatellites were less common in tiger salamanders than in either lake sturgeon or kangaroo rats. Across libraries, trinucleotides were found more frequently than any other motif type, presumably because they do not cause frameshift mutations. By evaluating variation across reads assembled to a given contig, we were able to identify repeat motifs likely to be polymorphic. Our study represents one of the first comparative data sets on the distribution of vertebrate microsatellites within expressed genes. Our results reinforce the idea that microsatellites do not always occur in noncoding DNA, but commonly occur in expressed genes.

  20. Characterizing the nutritional strategy of incubating king eiders Somateria spectabilis in northern Alaska

    USGS Publications Warehouse

    Bentzen, R.L.; Powell, A.N.; Williams, T.D.; Kitaysky, A.S.

    2008-01-01

    We measured plasma concentrations of variables associated with lipid metabolism (free fatty acids, glycerol, triglyceride, and ??- hydroxybutyrate), protein metabolism (uric acid), and baseline corticosterone to characterize the nutritional state of incubating king eiders Somateria spectabilis and relate this to incubation constancy at two sites, Kuparuk and Teshekpuk, in northern Alaska. King eiders at both sites appeared to employ a partial-income incubation strategy, relying on both endogenous and exogenous energy resources. Females maintained high invariant levels of free fatty acids, ??-hydroxybutyrate, and glycerol throughout incubation, indicating that fat reserves were a major energy source, and not completely depleted during incubation. Similarly, uric acid did not increase, suggesting effective protein sparing or protein ingestion and adequate lipid reserves throughout incubation. Baseline corticosterone and triglyceride levels increased during incubation, indicative of an increase in foraging during late stages of incubation. Incubating females at Kuparuk had higher triglyceride concentrations but also had higher ??-hydroxybutyrate concentrations than females at Teshekpuk. This dichotomy may reflect a short-term signal of feeding overlaying the longer-term signal of reliance on endogenous lipid reserves due to higher food intake yet higher metabolic costs at Kuparuk because of its colder environment. Incubation constancy was not correlated with plasma concentrations of lipid or protein metabolites. ?? 2008 The Authors.

  1. Fractionation of Eremurus spectabilis fructans by ethanol: Box-Behnken design and principal component analysis.

    PubMed

    Pourfarzad, Amir; Habibi Najafi, Mohammad B; Haddad Khodaparast, Mohammad H; Hassanzadeh Khayyat, Mohammad; Malekpour, Akbar

    2014-06-15

    The fructans, inulin and oligofructose, are known to exert many food and pharmaceutical applications and are widely used in functional foods throughout the world for their nutritional and techno-functional properties. In the present study, the Box-Behnken design was used to determine the optimal conditions for fructan precipitation from Eremurus spectabilis root powder (Serish) by adding ethanol that gave the maximum yield. Ethanol-to-syrup (E/S) ratio (2:1-15:1), precipitation temperature (30-60°C) and syrup concentration (10-40°B) were considered variables of fructan precipitation. The most compatible model among mean, linear and quadratic expressions was fitted to each response and the regression coefficients were determined using least square method. There was a good agreement between the experimental data and their predicted counterparts. The optimum conditions for fractionating fructan composition of Serish by ethanol were estimated to be E/S ratio of 8.56, temperature of 23.51°C and initial syrup concentration of 40°B. Precipitation under these optimized conditions achieved the best yield (85.81%), average chain length (12.92) and purity (80.18%). In addition, principal component analysis (PCA) allowed discriminating among precipitated fructan specialties.

  2. Choanoflagellate lorica construction and assembly: the nudiform condition. II. Acanthoeca spectabilis Ellis.

    PubMed

    Leadbeater, Barry S C; Henouil, Magali; Berovic, Nikolas

    2008-07-01

    Acanthoeca spectabilis is one of the most common loricate choanoflagellates found in marine biofilms everywhere. However, it is special for two reasons; firstly, it is probably the most distinctive member of the small nudiform clade of loricate choanoflagellates. Secondly, the lorica chamber of Acanthoeca comprises a closely wound left-handed coil of costae that is unique amongst choanoflagellates. Mathematical analysis of the lorica chamber shows that the helical costae undergo two turns. This species, more than any, demonstrates that the helical coiling of costae can only be achieved by a rotational movement generated by the cell during lorica assembly. Comparison of the lorica morphology of Acanthoeca with that of the closely related genus Polyoeca indicates that the helical costae of Acanthoeca are probably homologous with the outer longitudinal costae of Polyoeca. This is unusual because helical costae are usually the innermost layer of costae. However, since there is no 'true' inner layer in the chamber of Acanthoeca the outer layer of costae are adjacent to the cell surface and therefore available for coiling. In contrast to tectiform choanoflagellates, which number more than one hundred species and inhabit a wide variety of microniches, the six known extant nudiform species must either represent a minor evolutionary development or be the remnants of a previously more extensive radiation.

  3. Species-specific footdrumming in kangaroo rats: Dipodomys ingens, D. deserti, D. spectabilis

    PubMed

    Randall

    1997-11-01

    Footdrumming was compared in three allopatric species of kangaroo rat, Dipodomysfrom three habitats. Analysis of footdrumming recordings revealed species-specific patterns of drumming ranging from single thumps to individual footdrumming signatures. The desert kangaroo rat, D. desertidrums single thumps spaced 0.25-0.30 s apart that are sometimes introduced with a short footroll. The giant kangaroo rat, D. ingensdrums long footrolls that can average over 100 drums at 18 drums/s. The banner-tailed kangaroo rat, D. spectabilisdrums three to 38 footdrums in a footroll combined into sequences of two to 12 footrolls at a rate of 17 drums/s. In playback tests, all three species stood in alert postures and entered the burrow in response to footdrumming of their own and the other species. The rats also responded in species-specific ways. Dipodomys spectabilisdrummed to its own species' footdrumming, but not to playbacks of the single drums of D. desertiInstead of footdrumming to playbacks of its own species, D. deserti approached the speaker more frequently than did either of the other two species. Dipodomys ingens footdrummed equally to all footdrumming playbacks. The species' differences reflect differences in social tolerance and spacing. Dipodomys deserti rarely engages in footdrumming exchanges and chases visitors from the burrow. Dipodomys spectabilis engages in frequent footdrumming exchanges and some chases, and D. ingens seems to tolerate close neighbours and footdrums periodically.Copyright 1997 The Association for the Study of Animal Behaviour1997The Association for the Study of Animal Behaviour

  4. SUSTAINABILITY EFFECTS OF Crotalaria juncea L. AND Crotalaria spectabilis ROTH ON SOIL FERTILITY AND SOIL CONSERVATION

    NASA Astrophysics Data System (ADS)

    László, Márton, ,, Dr.

    2010-05-01

    Sustainable agriculture is defined as the successful management of resources for agriculture to satisfy changing human needs while maintaining or enhancing the quality of the environment and conserving natural resources. A sustained increase of agricultural production becomes a great possibility for international community. In this process a green manure crops application for example crotalaria get a new chance for improvement process on soil fertility and soil conservation. Field experiment was carried out on a calcareous chernozem soil (Experiment station Nagyhörcsök of RISSAC-HAS) in partly of experiment series (3 years) at Hungary in 1998. The soil with about 20% clay, 3% humus, 5% CaCO3 in its ploughed layer. To ensure a sufficient macro and micronutrient supply in the whole experiment, 100 kg N, 100 kg P2O5 and 100 kg K2O were given hectare. The Crotalaria juncea L. and Crotalaria spectabilis ROTH were applied with 2 replications. Each plot has an area of 45 m2 with 230-230 individual plants. In vegetation grown period were measured green and dry matter yield. The soil and plant samples were analysed for the macro and microelements contents. The main results achieved in 1998 are summarized as follows: 1. The green matter yield at before flowering reached 63.8 t ha-1 in case of Crotalaria juncea L. 2. Total dry matter yield at harvest (without roots) fluctuated between 9.6 and 17.0 t ha-1, depending on the crotalaria species. 3. The average of element concentration (including stems, leaves of Crotalaria juncea L. and Crotalaria spectabilis ROTH) before flowering reached to 3.2 % N, 2.3 % Ca, 1.3 % K, 0.39 % Mg, 0.22 % P and 0.24 % S. The content of Al and Fe total 14 - 25, while that of Sr, Mn, Na, B and Ba 2 - 6 ppm in dry matter. The Zn, Cu, Mo, Cr, Se, Ni, As, Pb, Cd and Co concentration did not reach here the value of 1 ppm. 4. The average of biological activated element uptake (including stems, leaves of Crotalaria juncea L. and Crotalaria spectabilis

  5. Analysis of potential water-supply management options, 2010-60, and documentation of revisions to the model of the Irwin Basin Aquifer System, Fort Irwin National Training Center, California

    USGS Publications Warehouse

    Voronin, Lois M.; Densmore, Jill N.; Martin, Peter

    2014-01-01

    The Fort Irwin National Training Center is considering several alternatives to manage their limited water-supply sources in the Irwin Basin. An existing three-dimensional, finite-difference groundwater-flow model—the U.S. Geological Survey’s MODFLOW—of the aquifer system in the basin was updated and the initial input dataset was supplemented with groundwater withdrawal data for the period 2000–10. The updated model was then used to simulate four combinations, or scenarios, of groundwater withdrawal and recharge over the next 50 years (January 2011 through December 2060). The scenarios included combinations of continuing withdrawals from currently active production wells, supplementing any increases in demand with withdrawals from an inactive production well, reducing withdrawal amounts and rates, and reducing the discharge of treated wastewater to infiltration ponds that provide a recharge source to the underlying aquifer. Results of the simulations indicated that, depending on the scenario implemented, groundwater levels would rise (over the next 50 years) from 40 feet to as much as 65 feet in the northwestern part of the Irwin Basin, and from 5 feet to 10 feet in the southeastern part.

  6. Regulation of plasma antidiuretic hormone in the dehydrated kangaroo rat (Dipodomys spectabilis M.).

    PubMed

    Stallone, J N; Braun, E J

    1988-01-01

    A sensitive and specific radioimmunoassay was used to measure plasma antidiuretic hormone (plasma arginine vasopressin, PAVP) concentrations in a conscious desert-adapted mammal, the banner-tailed kangaroo rat (Dipodomys spectabilis; 131 +/- 2.3 g body mass), during normal hydration and in response to progressive dehydration. Simultaneous measurements of PAVP and plasma osmolality (POSM) in these experiments permitted determination of the hypothalamo-neurohypophyseal system-osmoreceptor set point and sensitivity to extracellular hyperosmolality during dehydration. In normally hydrated kangaroo rats, acclimated to room temperature (20-24 degrees) and fed a dry grain diet, POSM and PAVP averaged 308.6 +/- 0.7 mosmol/kg H2O and 6.0 +/- 0.7 pg/ml (2.2 +/- 0.2 microU/ml), respectively (means +/- SE). In separate groups of animals subjected to 48, 96, 144, or 192 hr of dehydration, POSM and PAVP increased in a parallel linear manner with time to maxima of 329.7 +/- 2.4 mosmol/kg H2O and 68.8 +/- 4.4 pg/ml (24.9 +/- 1.6 microU/ml), respectively, at 192 hr of dehydration. Thus, a highly correlated and significant relationship between POSM and PAVP (r2 = 0.941, P less than 0.001) exists in dehydrated kangaroo rats, quantitatively defined by the linear regression equation PAVP (pg/ml) = 2.99 (POSM - 306.4), with an apparent osmotic threshold for AVP release at a POSM of 306.4 mosmol/kg H2O.(ABSTRACT TRUNCATED AT 250 WORDS)

  7. Basement structure beneath Langford Well Lake basin, Fort Irwin, California, based on inversion of gravity data

    USGS Publications Warehouse

    Morin, Robert L.

    2000-01-01

    Gravity data were used to study the basement structure of Langford Well Lake basin at the U.S. Army National Training Center, Fort Irwin, California. Figure 1 shows the location of the study area. During 1996 and 1999, 290 new gravity stations were measured. These data were merged with existing data to produce a depth-to-basement map, which, in turn was converted to a structure map of the basement surface below alluvial fill. This information can be used to help interpret water flow and reservoir capacity of the basin. In addition, gravity gradients were used to suggest locations of faults through or below alluvial fill. These gradients may be evidence for repositioning or extending mapped faults. The locations of gravity stations are shown in figure 2 plotted on a colored grid of topographic elevations generated from 30 m DEM's (Digital Elevation Models). As shown by figure 3, gravity data used in this study are sufficiently accurate to permit 1-mGal contour intervals. Much of the older regional data in this study area are of lesser quality although they were included because they sufficiently represent regional gravity.

  8. SUSTAINABILITY EFFECTS OF Crotalaria juncea L. AND Crotalaria spectabilis ROTH ON SOIL FERTILITY AND SOIL CONSERVATION

    NASA Astrophysics Data System (ADS)

    László, Márton, ,, Dr.

    2010-05-01

    Sustainable agriculture is defined as the successful management of resources for agriculture to satisfy changing human needs while maintaining or enhancing the quality of the environment and conserving natural resources. A sustained increase of agricultural production becomes a great possibility for international community. In this process a green manure crops application for example crotalaria get a new chance for improvement process on soil fertility and soil conservation. Field experiment was carried out on a calcareous chernozem soil (Experiment station Nagyhörcsök of RISSAC-HAS) in partly of experiment series (3 years) at Hungary in 1998. The soil with about 20% clay, 3% humus, 5% CaCO3 in its ploughed layer. To ensure a sufficient macro and micronutrient supply in the whole experiment, 100 kg N, 100 kg P2O5 and 100 kg K2O were given hectare. The Crotalaria juncea L. and Crotalaria spectabilis ROTH were applied with 2 replications. Each plot has an area of 45 m2 with 230-230 individual plants. In vegetation grown period were measured green and dry matter yield. The soil and plant samples were analysed for the macro and microelements contents. The main results achieved in 1998 are summarized as follows: 1. The green matter yield at before flowering reached 63.8 t ha-1 in case of Crotalaria juncea L. 2. Total dry matter yield at harvest (without roots) fluctuated between 9.6 and 17.0 t ha-1, depending on the crotalaria species. 3. The average of element concentration (including stems, leaves of Crotalaria juncea L. and Crotalaria spectabilis ROTH) before flowering reached to 3.2 % N, 2.3 % Ca, 1.3 % K, 0.39 % Mg, 0.22 % P and 0.24 % S. The content of Al and Fe total 14 - 25, while that of Sr, Mn, Na, B and Ba 2 - 6 ppm in dry matter. The Zn, Cu, Mo, Cr, Se, Ni, As, Pb, Cd and Co concentration did not reach here the value of 1 ppm. 4. The average of biological activated element uptake (including stems, leaves of Crotalaria juncea L. and Crotalaria spectabilis

  9. Milliwatt dc/dc Inverter

    NASA Technical Reports Server (NTRS)

    Mclyman, C. W.

    1983-01-01

    Compact dc/dc inverter uses single integrated-circuit package containing six inverter gates that generate and amplify 100-kHz square-wave switching signal. Square-wave switching inverts 10-volt local power to isolated voltage at another desired level. Relatively high operating frequency reduces size of filter capacitors required, resulting in small package unit.

  10. Development of Natural Alkalinity in Appalachian Deep Coal Mine Discharges, Irwin Syncline, Pennsylvania, USA

    NASA Astrophysics Data System (ADS)

    Bryant, E. M.; Winters, W. R.; Winters, W. R.; Capo, R. C.

    2001-12-01

    Geochemical processes in flooded underground coal mine complexes are controlled by the relationship between overburden mineralogy and the hydrogeologic system, which is influenced by mining methodology and discharge location. Numerous large flow (over 2,000 L/min), historically acidic, deep mine discharges in Appalachian bituminous coal basins are now net alkaline, with circumneutral pH and high concentrations of dissolved iron (20-80 ppm) and sodium (100-500 ppm) [1]. Understanding natural alkalinity production offers alternative approaches for neutralizing acid mine drainage (AMD) and has implications for predictive models, mining regulations, mine discharge remediation, and resource recovery. To determine the subsurface processes involved in the generation of natural alkalinity, we focused on the Irwin syncline, a 240 sq.-km bituminous coal basin in southwestern Pennsylvania. All major streams that arise within or cross the syncline are affected by polluted mine drainage. The pollution ranges from highly acidic iron- and aluminum-contaminated discharges in the northern portion of the basin to highly alkaline, iron and sulfate-contaminated discharges in the southern portion. Underground mine barrier data were used to divide the basin into six hydraulically related sub-basins; mine waters were collected from nine discharges across the basin [2]. Sub-basin hydrology was integrated with infiltration, discharge, and overburden geochemistry and mineralogy. Modeling of Irwin syncline flows using a solute modeling program (PHREEQC 2.4.2; [3]) indicates that the spatial and temporal change in mine water chemistry involves processes other than simple carbonate dissolution or dilution with uncontaminated water. Results indicate that the acidic discharges in the northeastern end of the basin are the product of surface water modified by pyrite oxidation and dissolution of aluminosilicate minerals. Sodium concentrations in those flows are likely the result of minor halite

  11. Recent demographic bottlenecks are not accompanied by a genetic signature in banner-tailed kangaroo rats (Dipodomys spectabilis).

    PubMed

    Busch, Joseph D; Waser, Peter M; Dewoody, J Andrew

    2007-06-01

    Single-sample methods of bottleneck detection are now routine analyses in studies of wild populations and conservation genetics. Three common approaches to bottleneck detection are the heterozygosity excess, mode-shift, and M-ratio tests. Empirical groundtruthing of these methods is difficult, but their performances are critical for the accurate reconstruction of population demography. We use two banner-tailed kangaroo rat (Dipodomys spectabilis) populations from southeastern Arizona (USA) that are known to have experienced recent demographic reductions to search for genetic bottleneck signals with eight microsatellite loci. Over eight total sample-years, neither population showed a genetic bottleneck signature. M-ratios in both populations were large, stable, and never fell below a critical significance value (Mc). The mode shift test did not detect any distortion of allele frequencies, and tests of heterozygosity excess were not significant in postbottleneck samples when we used standard microsatellite mutation models. The genetic effects of bottlenecks like those experienced by our study populations should be strongly influenced by rates of mutation and migration. We used genetic parentage data to estimate a relatively high mutation rate in D. spectabilis (0.0081 mutants/generation/locus), but mutation alone is unlikely to explain the temporal distribution of rare alleles that we observed. Migration (gene flow) is a more likely explanation, despite prior mark-recapture analysis that estimated very low rates of interpopulation dispersal. We interpret our kangaroo rat data in light of the broader literature and conclude that in natural populations connected by dispersal, demographic bottlenecks may prove difficult to detect using molecular genetic data.

  12. Bio Prospecting of Marine-derived Streptomyces spectabilis VITJS10 and Exploring its Cytotoxicity Against Human Liver Cancer Cell Lines

    PubMed Central

    Selvakumar, Jemimah Naine; Chandrasekaran, Subathra Devi; Vaithilingam, Mohanasrinivasan

    2015-01-01

    Background: Recently, numerous pathogens have developed resistance due to the indiscriminate use of commercial therapeutic drugs. Objective: The main aim of the study was to evaluate the bioactive potential of the Streptomyces spectabilis VITJS10 crude extract. Materials and Methods: The S. spectabilis VITJS10 ethyl acetate extract was tested for antibacterial, antioxidant, and cytotoxic properties. Genotypic characterization was done using 16S r-DNA partial gene amplification and sequencing. The authenticity of the crude chemical constitutes were determined by gas chromatography–mass spectrometry (GC-MS). Results: The antibacterial potential revealed the effective activity against Shigellaflexneri (MTCC No: 1457) (22 mm), Salmonella typhi (MTCC No: 1167) (23 mm), Escherichia coli (MTCC No: 1588) (22 mm), Pseudomonas aeruginosa (MTCC No: 4676) (22 mm) at 20 mg/mL concentration. Scavenging ability of the extract was determined using 2,2-diphenyl-1-picrylhydrazyl (DPPH) assay revealing its 95% inhibition at 5 mg/mL concentration. Hepatocellular cancer cells (HepG2) cell line was used to evaluate the cytotoxicity by 3-(4, 5-dimethyl thiazol-2yl)-2, 5-diphenyl tetrazolium bromide assay. The extract showed maximum inhibition at IC50 of 250 μg/mL with 53.6% cell viability. The highest 16S rRNA gene sequence homogeneity was observed 99% similar with the novel strain S. spectabilis S3-1. The chemical components of the crude extract of VITJS10 were detected with 37 chemical constituents. However three major compounds were identified, namely Sulfurous acid, 2-ethylhexyl tridecyl ester, Phenol, 2,4-bis (1,1-dimethylethyl), and Trans-2-methyl-4-n-pentylthiane, S, S-Dioxide. Conclusion: Hence the present study justifies the overwhelming circumstantial evidence as the most bioactive metabolites from the marine origin, which has potential utilization in pharmaceutical industry. SUMMARY The aim of this study was to explore the bioactive potential of marine Streptomyces sp

  13. Adaptable DC offset correction

    NASA Technical Reports Server (NTRS)

    Golusky, John M. (Inventor); Muldoon, Kelly P. (Inventor)

    2009-01-01

    Methods and systems for adaptable DC offset correction are provided. An exemplary adaptable DC offset correction system evaluates an incoming baseband signal to determine an appropriate DC offset removal scheme; removes a DC offset from the incoming baseband signal based on the appropriate DC offset scheme in response to the evaluated incoming baseband signal; and outputs a reduced DC baseband signal in response to the DC offset removed from the incoming baseband signal.

  14. 1996 Water-Table Contours of the Mojave River, the Morongo, and the Fort Irwin Ground-Water Basins, San Bernardino County, California

    USGS Publications Warehouse

    Predmore, Steven K.

    2003-01-01

    This data set consists of digital water-table contours for the Mojave River, the Morongo and the Fort Irwin Ground-Water Basins. The U.S. Geological Survey constructed a water-table map of the Mojave River, the Morongo and the Fort Irwin Ground-Water Basins for ground-water levels measured during the period January-September 1996. Water-level data were collected from 632 wells to construct the contours. The water-table contours were digitized from the paper map which was published at a scale of 1:175,512. The contour interval ranges from 3,400 to 1,550 feet above sea level.

  15. Volcanic stratigraphy and geochemical variations in Miocene-age rocks in western and southeastern Fort Irwin, California

    NASA Astrophysics Data System (ADS)

    Buesch, D.

    2015-12-01

    Lava flows and tuffaceous deposits ranging in composition from basalt to rhyolite, including basaltic trachyandesite to trachyte, are exposed in 800 km2 of western Fort Irwin area, California, and form the eastern edge of the Eagle Crags volcanic field (ECVF). The main ECVF has 40Ar/39Ar ages from ~18.7-12.4 Ma (mostly 18.7-18.5 Ma; Sabin et al. 1994), and on Fort Irwin, the ages are from 21.0-15.8 Ma (mostly 18.6-15.8 Ma; Schermer et al. 1996). 68 samples (56 lava flow, 4 dome-collapse breccia, 3 ignimbrite, and 5 fallout tephra) were analyzed for major, minor, and trace elements. Typically, stratigraphic sequences dip <30° (mostly <15°) except near faults, with local buttress unconfomities and no large unconfomities. Compositions are moderate-to-high-K type, and similar to Na2O+K2O from Sabin et al. (1994) but with slightly smaller ranges. The generalized stratigraphic sequence is rhyolite (R), dacite (D), or trachyte (T) that form domes, lava flows (up to 3.5 km long), dome-collapse deposits, or pyroclastic deposits, overlain by andesite (A), trachyandesite (TA), basaltic andesite (BA), basaltic trachyandesite (BT), or basalt (B) lava flows (up to 7 km long), and minor cinder cones. A general upward felsic to mafic compositional sequence occurs throughout the area, but is not continuous as B is locally in a R-D sequence and B is at the base of and interstratified with a BA-A sequence. Also, there are compositional variations at different locations along the edges of the field. In the Goldstone Mesa, Pink Canyon, and Stone Ridge areas (~70 km2), B-BA forms the youngest lava flows, but ~21 km to the north in the Garry Owen area (~25 km2), BTA forms the youngest lava flows. Compared to the Stone Ridge area with a D-A-TA-BA trend, ~6 km west in the Pioneer Plateau area is R-TA-D, ~3 km south in the Pink Canyon area is R-B-BA-A, and ~8 km east at Dacite Dome is D only (all areas have slightly different Na2O+K2O in each rock type). A non-ECVF, 5.6 Ma BA flow in SE

  16. High-Efficiency dc/dc Converter

    NASA Technical Reports Server (NTRS)

    Sturman, J.

    1982-01-01

    High-efficiency dc/dc converter has been developed that provides commonly used voltages of plus or minus 12 Volts from an unregulated dc source of from 14 to 40 Volts. Unique features of converter are its high efficiency at low power level and ability to provide output either larger or smaller than input voltage.

  17. Time-domain electromagnetic surveys at Fort Irwin, San Bernardino County, California, 2010-12: Chapter F in Geology and geophysics applied to groundwater hydrology at Fort Irwin, California

    USGS Publications Warehouse

    Burgess, Matthew K.; Bedrosian, Paul A.; Buesch, David C.

    2014-01-01

    Between 2010 and 2012, a total of 79 time-domain electromagnetic (TEM) soundings were collected in 12 groundwater basins in the U.S. Army Fort Irwin National Training Center (NTC) study area to help improve the understanding of the hydrogeology of the NTC. The TEM data are discussed in this chapter in the context of geologic observations of the study area, the details of which are provided in the other chapters of this volume. Selection of locations for TEM soundings in unexplored basins was guided by gravity data that estimated depth to pre-Tertiary basement complex of crystalline rock and alluvial thickness. Some TEM data were collected near boreholes with geophysical logs. The TEM response at locations near boreholes was used to evaluate sounding data for areas without boreholes. TEM models also were used to guide site selection of subsequent boreholes drilled as part of this study. Following borehole completion, geophysical logs were used to ground-truth and reinterpret previously collected TEM data. This iterative process was used to site subsequent TEM soundings and borehole locations as the study progressed. Although each groundwater subbasin within the NTC boundaries was explored using the TEM method, collection of TEM data was focused in those basins identified as best suited for development of water resources. At the NTC, TEM estimates of some lithologic thicknesses and electrical properties in the unsaturated zone are in good accordance with borehole data; however, water-table elevations were not easily identifiable from TEM data.

  18. Dispersal, movements and site fidelity of post-fledging King Eiders Somateria spectabilis and their attendant females

    USGS Publications Warehouse

    Bentzen, Rebecca L.; Powell, Abby N.

    2015-01-01

    Post-fledging dispersal and site fidelity are poorly understood, particularly for sea ducks that spend the majority of their annual cycle at sea. This is the first description of movements and their timing for first-year (juvenile) and second-year (subadult) King Eiders Somateria spectabilis in relation to their attendant females. We fitted satellite transmitters that operated for 2 years to 63 hatch-year birds and 17 attendant females at breeding areas in northern Alaska in 2006–2009. Our goals were to describe the spatio-temporal distribution of pre-breeding individuals and adult females that had been successful breeders. We also examined fidelity to wing moulting and wintering areas as well as natal philopatry. Juveniles did not appear to follow attendant adults, although they did winter in the same three general wintering areas, suggesting that genetic inheritance and social factors may have roles in the initial migration from the breeding area. Additionally, juveniles were more variable in the timing and duration of migration, moved longer distances during the winter, and were less faithful to moulting and wintering areas than adults, indicating that individual exploration and acquired navigational memory played a role in subsequent migrations. Most (75%) subadult females returned to natal areas, probably prospecting for future nesting sites, whereas subadult males were widely dispersed at sea. Timing and duration of moult migration and wing moult of adult females that were presumed to be successful breeders differed from those of unsuccessful breeders due to the extended time that the former spent on the breeding grounds. Temporal and spatial segregation of post-fledging King Eiders from adults has direct management implications in terms of resource development and population dynamics.

  19. Characterization of expressed class II MHC sequences in the banner-tailed kangaroo rat (Dipodomys spectabilis) reveals multiple DRB loci.

    PubMed

    Busch, Joseph D; Waser, Peter M; DeWoody, J Andrew

    2008-11-01

    Genes of the major histocompatibility complex (MHC) are exceptionally polymorphic due to the combined effects of natural and sexual selection. Most research in wild populations has focused on the second exon of a single class II locus (DRB), but complete gene sequences can provide an illuminating backdrop for studies of intragenic selection, recombination, and organization. To this end, we characterized class II loci in the banner-tailed kangaroo rat (Dipodomys spectabilis). Seven DRB-like sequences (provisionally named MhcDisp-DRB*01 through *07) were isolated from spleen cDNA and most likely comprise > or =5 loci; this multiformity is quite unlike the situation in muroid rodents such as Mus, Rattus, and Peromyscus. In silico translation revealed the presence of important structural residues for glycosylation sites, salt bonds, and CD4+ T-cell recognition. Amino-acid distances varied widely among the seven sequences (2-34%). Nuclear DNA sequences from the Disp-DRB*07 locus (approximately 10 kb) revealed a conventional exon/intron structure as well as a number of microsatellites and short interspersed nuclear elements (B4, Alu, and IDL-Geo subfamilies). Rates of nucleotide substitution at Disp-DRB*07 are similar in both exons and introns (pi = 0.015 and 0.012, respectively), which suggests relaxed selection and may indicate that this locus is an expressed pseudogene. Finally, we performed BLASTn searches against Dipodomys ordii genomic sequences (unassembled reads) and find 90-97% nucleotide similarity between the two kangaroo rat species. Collectively, these data suggest that class II diversity in heteromyid rodents is based on polylocism and departs from the muroid architecture.

  20. Projected climate and vegetation changes and potential biotic effects for Fort Benning, Georgia; Fort Hood, Texas; and Fort Irwin, California

    USGS Publications Warehouse

    Shafer, S.L.; Atkins, J.; Bancroft, B.A.; Bartlein, P.J.; Lawler, J.J.; Smith, B.; Wilsey, C.B.

    2012-01-01

    The responses of species and ecosystems to future climate changes will present challenges for conservation and natural resource managers attempting to maintain both species populations and essential habitat. This report describes projected future changes in climate and vegetation for three study areas surrounding the military installations of Fort Benning, Georgia, Fort Hood, Texas, and Fort Irwin, California. Projected climate changes are described for the time period 2070–2099 (30-year mean) as compared to 1961–1990 (30-year mean) for each study area using data simulated by the coupled atmosphere-ocean general circulation models CCSM3, CGCM3.1(T47), and UKMO-HadCM3, run under the B1, A1B, and A2 future greenhouse gas emissions scenarios. These climate data are used to simulate potential changes in important components of the vegetation for each study area using LPJ, a dynamic global vegetation model, and LPJ-GUESS, a dynamic vegetation model optimized for regional studies. The simulated vegetation results are compared with observed vegetation data for the study areas. Potential effects of the simulated future climate and vegetation changes for species and habitats of management concern are discussed in each study area, with a particular focus on federally listed threatened and endangered species.

  1. DC/DC Converter Stability Testing Study

    NASA Technical Reports Server (NTRS)

    Wang, Bright L.

    2008-01-01

    This report presents study results on hybrid DC/DC converter stability testing methods. An input impedance measurement method and a gain/phase margin measurement method were evaluated to be effective to determine front-end oscillation and feedback loop oscillation. In particular, certain channel power levels of converter input noises have been found to have high degree correlation with the gain/phase margins. It becomes a potential new method to evaluate stability levels of all type of DC/DC converters by utilizing the spectral analysis on converter input noises.

  2. Wind erodibility of soils at Fort Irwin, California (Mojave Desert), USA, before and after trampling disturbance: Implications for land management

    USGS Publications Warehouse

    Belnap, J.; Phillips, S.L.; Herrick, J.E.; Johansen, J.R.

    2007-01-01

    Recently disturbed and 'control' (i.e. less recently disturbed) soils in the Mojave Desert were compared for their vulnerability to wind erosion, using a wind tunnel, before and after being experimentally trampled. Before trampling, control sites had greater cyanobacterial biomass, soil surface stability, threshold friction velocities (TFV, i.e. the wind speed required to move soil particles), and sediment yield than sites that had been more recently disturbed by military manoeuvres. After trampling, all sites showed a large drop in TFVs and a concomitant increase in sediment yield. Simple correlation analyses showed that the decline in TFVs and the rise in sediment yield were significantly related to cyanobacterial biomass (as indicated by soil chlorophyll a). However, chlorophyll a amounts were very low compared to chlorophyll a amounts found at cooler desert sites, where chlorophyll a is often the most important factor in determining TFV and sediment yield. Multiple regression analyses showed that other factors at Fort Irwin were more important than cyanobacterial biomass in determining the overall site susceptibility to wind erosion. These factors included soil texture (especially the fine, medium and coarse sand fractions), rock cover, and the inherent stability of the soil (as indicated by subsurface soil stability tests). Thus, our results indicate that there is a threshold of biomass below which cyanobacterial crusts are not the dominant factor in soil vulnerability to wind erosion. Most undisturbed soil surfaces in the Mojave Desert region produce very little sediment, but even moderate disturbance increases soil loss from these sites. Because current weathering rates and dust inputs are very low, soil formation rates are low as well. Therefore, soil loss in this region is likely to have long-term effects.

  3. Beetles that live with ants (Coleoptera, Carabidae, Pseudomorphini): A remarkable new genus and species from Guyane (French Guiana), Guyanemorpha spectabilis gen. n., sp. n.

    PubMed Central

    Erwin, Terry L.

    2013-01-01

    Abstract Among the extensive collections currently being made in Guyane (French Guiana), adults of a large and colorful species of pseudomorphine were encountered. The adults present, for the first time in the Western Hemisphere, elytra with a marked color pattern, and in addition a size considerably beyond that of the rest of the members of all other known genera in the Western Hemisphere. Both of these attributes, however, are well known in the Australian pseudomorphine fauna. This new species is described and illustrated and a revised key to the Western Hemisphere genera is included. The type locality of Guyanemorpha spectabilis gen. n., sp. n. is Guyane,Risquetout, PK20, 4.916°N, 52.516°W, 12m altitude. PMID:24363582

  4. Beetles that live with ants (Coleoptera, Carabidae, Pseudomorphini): A remarkable new genus and species from Guyane (French Guiana), Guyanemorpha spectabilis gen. n., sp. n.

    PubMed

    Erwin, Terry L

    2013-01-01

    Among the extensive collections currently being made in Guyane (French Guiana), adults of a large and colorful species of pseudomorphine were encountered. The adults present, for the first time in the Western Hemisphere, elytra with a marked color pattern, and in addition a size considerably beyond that of the rest of the members of all other known genera in the Western Hemisphere. Both of these attributes, however, are well known in the Australian pseudomorphine fauna. This new species is described and illustrated and a revised key to the Western Hemisphere genera is included. The type locality of Guyanemorpha spectabilis gen. n., sp. n. is Guyane,Risquetout, PK20, 4.916°N, 52.516°W, 12m altitude.

  5. DC source assemblies

    DOEpatents

    Campbell, Jeremy B; Newson, Steve

    2013-02-26

    Embodiments of DC source assemblies of power inverter systems of the type suitable for deployment in a vehicle having an electrically grounded chassis are provided. An embodiment of a DC source assembly comprises a housing, a DC source disposed within the housing, a first terminal, and a second terminal. The DC source also comprises a first capacitor having a first electrode electrically coupled to the housing, and a second electrode electrically coupled to the first terminal. The DC source assembly further comprises a second capacitor having a first electrode electrically coupled to the housing, and a second electrode electrically coupled to the second terminal.

  6. Identification of disrupted surfaces due to military activity at the Ft. Irwin National Training Center: An aerial photograph and satellite image analysis

    SciTech Connect

    McCarthy, L.E.; Marsh, S.E.; Lee, C.

    1996-07-01

    Concern for environmental management of our natural resources is most often focused on the anthropogenic impacts placed upon these resources. Desert landscapes, in particular, are fragile environments, and minimal stresses on surficial materials can greatly increase the rate and character of erosional responses. The National Training Center, Ft. Irwin, located in the middle of the Mojave Desert, California, provides an isolated study area of intense ORV activity occurring over a 50-year period. Geomorphic surfaces, and surficial disruption from two study sites within the Ft. Irwin area were mapped from 1947, 1:28,400, and 1993 1:12,000 black and white aerial photographs. Several field checks were conducted to verify this mapping. However, mapping from black and white aerial photography relies heavily on tonal differences, patterns, and morphological criteria. Satellite imagery, sensitive to changes in mineralogy, can help improve the ability to distinguish geomorphic units in desert regions. In order to assess both the extent of disrupted surfaces and the surficial geomorphology discemable from satellite imagery, analysis was done on SPOT panchromatic and Landsat Thematic Mapper (TM) multispectral imagery acquired during the spring of 1987 and 1993. The resulting classified images provide a clear indication of the capabilities of the satellite data to aid in the delineation of disrupted geomorphic surfaces.

  7. Radiation effects on DC-DC Converters

    NASA Technical Reports Server (NTRS)

    Zhang, Dexin; Attia, John O.; Kankam, Mark D. (Technical Monitor)

    2000-01-01

    DC-DC switching converters are circuits that can be used to convert a DC voltage of one value to another by switching action. They are increasing being used in space systems. Most of the popular DC-DC switching converters utilize power MOSFETs. However power MOSFETs, when subjected to radiation, are susceptible to degradation of device characteristics or catastrophic failure. This work focuses on the effects of total ionizing dose on converter performance. Four fundamental switching converters (buck converter, buck-boost converter, cuk converter, and flyback converter) were built using Harris IRF250 power MOSFETs. These converters were designed for converting an input of 60 volts to an output of about 12 volts with a switching frequency of 100 kHz. The four converters were irradiated with a Co-60 gamma source at dose rate of 217 rad/min. The performances of the four converters were examined during the exposure to the radiation. The experimental results show that the output voltage of the converters increases as total dose increases. However, the increases of the output voltage were different for the four different converters, with the buck converter and cuk converter the highest and the flyback converter the lowest. We observed significant increases in output voltage for cuk converter at a total dose of 24 krad (si).

  8. DC-to-DC switching converter

    NASA Technical Reports Server (NTRS)

    Cuk, Slobodan M. (Inventor); Middlebrook, Robert D. (Inventor)

    1980-01-01

    A dc-to-dc converter having nonpulsating input and output current uses two inductances, one in series with the input source, the other in series with the output load. An electrical energy transferring device with storage, namely storage capacitance, is used with suitable switching means between the inductances to DC level conversion. For isolation between the source and load, the capacitance may be divided into two capacitors coupled by a transformer, and for reducing ripple, the inductances may be coupled. With proper design of the coupling between the inductances, the current ripple can be reduced to zero at either the input or the output, or the reduction achievable in that way may be divided between the input and output.

  9. Radiation Effects on DC-DC Converters

    NASA Technical Reports Server (NTRS)

    Zhang, De-Xin; AbdulMazid, M. D.; Attia, John O.; Kankam, Mark D. (Technical Monitor)

    2001-01-01

    In this work, several DC-DC converters were designed and built. The converters are Buck Buck-Boost, Cuk, Flyback, and full-bridge zero-voltage switched. The total ionizing dose radiation and single event effects on the converters were investigated. The experimental results for the TID effects tests show that the voltages of the Buck Buck-Boost, Cuk, and Flyback converters increase as total dose increased when using power MOSFET IRF250 as a switching transistor. The change in output voltage with total dose is highest for the Buck converter and the lowest for Flyback converter. The trend of increase in output voltages with total dose in the present work agrees with those of the literature. The trends of the experimental results also agree with those obtained from PSPICE simulation. For the full-bridge zero-voltage switch converter, it was observed that the dc-dc converter with IRF250 power MOSFET did not show a significant change of output voltage with total dose. In addition, for the dc-dc converter with FSF254R4 radiation-hardened power MOSFET, the output voltage did not change significantly with total dose. The experimental results were confirmed by PSPICE simulation that showed that FB-ZVS converter with IRF250 power MOSFET's was not affected with the increase in total ionizing dose. Single Event Effects (SEE) radiation tests were performed on FB-ZVS converters. It was observed that the FB-ZVS converter with the IRF250 power MOSFET, when the device was irradiated with Krypton ion with ion-energy of 150 MeV and LET of 41.3 MeV-square cm/mg, the output voltage increased with the increase in fluence. However, for Krypton with ion-energy of 600 MeV and LET of 33.65 MeV-square cm/mg, and two out of four transistors of the converter were permanently damaged. The dc-dc converter with FSF254R4 radiation hardened power MOSFET's did not show significant change at the output voltage with fluence while being irradiated by Krypton with ion energy of 1.20 GeV and LET of 25

  10. Multilevel DC link inverter

    DOEpatents

    Su, Gui-Jia

    2003-06-10

    A multilevel DC link inverter and method for improving torque response and current regulation in permanent magnet motors and switched reluctance motors having a low inductance includes a plurality of voltage controlled cells connected in series for applying a resulting dc voltage comprised of one or more incremental dc voltages. The cells are provided with switches for increasing the resulting applied dc voltage as speed and back EMF increase, while limiting the voltage that is applied to the commutation switches to perform PWM or dc voltage stepping functions, so as to limit current ripple in the stator windings below an acceptable level, typically 5%. Several embodiments are disclosed including inverters using IGBT's, inverters using thyristors. All of the inverters are operable in both motoring and regenerating modes.

  11. Monsoon Season Moisture Deficit Limits Growth in Co-Occurring Alpine Shrub (Cassiope fastigata) and Tree (Abies spectabilis) Species in the Central Himalayas, Nepal

    NASA Astrophysics Data System (ADS)

    Rayback, S. A.; Shrestha, K. B.; Hofgaard, A.

    2015-12-01

    Recent evidence indicates changing climatological conditions in the Nepalese Himalayas including decreasing precipitation, a weakening Indian monsoon and rising temperatures. Trees and shrubs found at treeline are considered to be highly sensitive to climate, but the climatic effects on these ecotone species in the Himalayas are not well understood. Dendrochronological techniques applied to co-occurring shrubs and trees up-and down-slope of treeline extend our understanding of vegetation response at range margins and into tree-less environments. We developed tree-ring width and annual height increment chronologies for Abies spectabilis (Himalayan fir) and the first annual growth increment and annual production of leaves chronologies for Cassiope fastigata (Himalayan heather) at a high elevation site in central Nepal. C. fastigata chronologies showed moisture availability in late pre-monsoon and monsoon seasons of the previous year are critical to stem elongation and leaf production (AGI and previous May-August SPEI-12, r = 0.790; LEAF and previous June-September SPEI-12, r = 0.708) A. spectabilis chronologies were significantly and negatively correlated with monsoon season temperature during the current year (tree-ring width and June mean temperature, r = -0.677; height-increment and Sept maximum temperature, r = -0.605). In addition to both long-term and recent declines in moisture in the Himalayas, moisture deficit may be further exacerbated at high elevation sites via run-off and higher levels of evapotranspiration resulting in growth reductions, dieback and even death of these species. These results highlight that not all mid-latitude, high elevation treelines are limited by temperature as previously thought and that severe drought stress may initiate downslope treeline retraction. Understanding the response of co-occurring tree and shrub species to climate, now and in the future, may help to elucidate the physiological mechanisms controlling local and

  12. Radiation-Tolerant DC-DC Converters

    NASA Technical Reports Server (NTRS)

    Skutt, Glenn; Sable, Dan; Leslie, Leonard; Graham, Shawn

    2012-01-01

    A document discusses power converters suitable for space use that meet the DSCC MIL-PRF-38534 Appendix G radiation hardness level P classification. A method for qualifying commercially produced electronic parts for DC-DC converters per the Defense Supply Center Columbus (DSCC) radiation hardened assurance requirements was developed. Development and compliance testing of standard hybrid converters suitable for space use were completed for missions with total dose radiation requirements of up to 30 kRad. This innovation provides the same overall performance as standard hybrid converters, but includes assurance of radiation- tolerant design through components and design compliance testing. This availability of design-certified radiation-tolerant converters can significantly reduce total cost and delivery time for power converters for space applications that fit the appropriate DSCC classification (30 kRad).

  13. Forback DC-to-DC converter

    NASA Astrophysics Data System (ADS)

    Lukemire, Alan T.

    1993-03-01

    A pulse-width modulated DC-to-DC power converter including a first inductor, i.e. a transformer or an equivalent fixed inductor equal to the inductance of the secondary winding of the transformer, coupled across a source of DC input voltage via a transistor switch which is rendered alternately conductive (ON) and nonconductive (OFF) in accordance with a signal from a feedback control circuit is described. A first capacitor capacitively couples one side of the first inductor to a second inductor which is connected to a second capacitor which is coupled to the other side of the first inductor. A circuit load shunts the second capacitor. A semiconductor diode is additionally coupled from a common circuit connection between the first capacitor and the second inductor to the other side of the first inductor. A current sense transformer generating a current feedback signal for the switch control circuit is directly coupled in series with the other side of the first inductor so that the first capacitor, the second inductor and the current sense transformer are connected in series through the first inductor. The inductance values of the first and second inductors, moreover, are made identical. Such a converter topology results in a simultaneous voltsecond balance in the first inductance and ampere-second balance in the current sense transformer.

  14. Forback DC-to-DC converter

    NASA Astrophysics Data System (ADS)

    Lukemire, Alan T.

    1995-05-01

    A pulse-width modulated DC-to-DC power converter including a first inductor, i.e. a transformer or an equivalent fixed inductor equal to the inductance of the secondary winding of the transformer, coupled across a source of DC input voltage via a transistor switch which is rendered alternately conductive (ON) and nonconductive (OFF) in accordance with a signal from a feedback control circuit is described. A first capacitor capacitively couples one side of the first inductor to a second inductor which is connected to a second capacitor which is coupled to the other side of the first inductor. A circuit load shunts the second capacitor. A semiconductor diode is additionally coupled from a common circuit connection between the first capacitor and the second inductor to the other side of the first inductor. A current sense transformer generating a current feedback signal for the switch control circuit is directly coupled in series with the other side of the first inductor so that the first capacitor, the second inductor and the current sense transformer are connected in series through the first inductor. The inductance values of the first and second inductors, moreover, are made identical. Such a converter topology results in a simultaneous voltsecond balance in the first inductance and ampere-second balance in the current sense transformer.

  15. Forback DC-to-DC converter

    NASA Technical Reports Server (NTRS)

    Lukemire, Alan T. (Inventor)

    1995-01-01

    A pulse-width modulated DC-to-DC power converter including a first inductor, i.e. a transformer or an equivalent fixed inductor equal to the inductance of the secondary winding of the transformer, coupled across a source of DC input voltage via a transistor switch which is rendered alternately conductive (ON) and nonconductive (OFF) in accordance with a signal from a feedback control circuit is described. A first capacitor capacitively couples one side of the first inductor to a second inductor which is connected to a second capacitor which is coupled to the other side of the first inductor. A circuit load shunts the second capacitor. A semiconductor diode is additionally coupled from a common circuit connection between the first capacitor and the second inductor to the other side of the first inductor. A current sense transformer generating a current feedback signal for the switch control circuit is directly coupled in series with the other side of the first inductor so that the first capacitor, the second inductor and the current sense transformer are connected in series through the first inductor. The inductance values of the first and second inductors, moreover, are made identical. Such a converter topology results in a simultaneous voltsecond balance in the first inductance and ampere-second balance in the current sense transformer.

  16. Intelligent dc-dc Converter Technology Developed and Tested

    NASA Technical Reports Server (NTRS)

    Button, Robert M.

    2001-01-01

    The NASA Glenn Research Center and the Cleveland State University have developed a digitally controlled dc-dc converter to research the benefits of flexible, digital control on power electronics and systems. Initial research and testing has shown that conventional dc-dc converters can benefit from improved performance by using digital-signal processors and nonlinear control algorithms.

  17. Construction, water-level, and water-quality data for multiple-well monitoring sites and test wells, Fort Irwin National Training Center, San Bernardino County, California, 2009-12

    USGS Publications Warehouse

    Kjos, Adam R.; Densmore, Jill N.; Nawikas, Joseph M.; Brown, Anthony A.

    2014-01-01

    Because of increasing water demands at the U.S. Army Fort Irwin National Training Center, the U.S. Geological Survey in cooperation with the U.S. Army carried out a study to evaluate the water quality and potential groundwater supply of undeveloped basins within the U.S. Army Fort Irwin National Training Center. In addition, work was performed in the three developed basins—Langford, Bicycle, and Irwin—proximal to or underlying cantonment to provide information in support of water-resources management and to supplement monitoring in these basins. Between 2009 and 2012, the U.S. Geological Survey installed 41 wells to expand collection of water-resource data within the U.S. Army Fort Irwin National Training Center. Thirty-four monitoring wells (2-inch diameter) were constructed at 14 single- or multiple-well monitoring sites and 7 test wells (8-inch diameter) were installed. The majority of the wells were installed in previously undeveloped or minimally developed basins (Cronise, Red Pass, the Central Corridor area, Superior, Goldstone, and Nelson Basins) proximal to cantonment (primary base housing and infrastructure). Data associated with well construction, water-level monitoring, and water-quality sampling are presented in this report.

  18. RISK D/C

    NASA Technical Reports Server (NTRS)

    Dias, W. C.

    1994-01-01

    RISK D/C is a prototype program which attempts to do program risk modeling for the Space Exploration Initiative (SEI) architectures proposed in the Synthesis Group Report. Risk assessment is made with respect to risk events, their probabilities, and the severities of potential results. The program allows risk mitigation strategies to be proposed for an exploration program architecture and to be ranked with respect to their effectiveness. RISK D/C allows for the fact that risk assessment in early planning phases is subjective. Although specific to the SEI in its present form, RISK D/C can be used as a framework for developing a risk assessment program for other specific uses. RISK D/C is organized into files, or stacks, of information, including the architecture, the hazard, and the risk event stacks. Although predefined, all stacks can be upgraded by a user. The architecture stack contains information concerning the general program alternatives, which are subsequently broken down into waypoints, missions, and mission phases. The hazard stack includes any background condition which could result in a risk event. A risk event is anything unfavorable that could happen during the course of a specific point within an architecture, and the risk event stack provides the probabilities, consequences, severities, and any mitigation strategies which could be used to reduce the risk of the event, and how much the risk is reduced. RISK D/C was developed for Macintosh series computers. It requires HyperCard 2.0 or later, as well as 2Mb of RAM and System 6.0.8 or later. A Macintosh II series computer is recommended due to speed concerns. The standard distribution medium for this package is one 3.5 inch 800K Macintosh format diskette. RISK D/C was developed in 1991 and is a copyrighted work with all copyright vested in NASA. Macintosh and HyperCard are trademarks of Apple Computer, Inc.

  19. DC Breakdown Experiments

    SciTech Connect

    Calatroni, S.; Descoeudres, A.; Levinsen, Y.; Taborelli, M.; Wuensch, W.

    2009-01-22

    In the context of the CLIC (Compact Linear Collider) project investigations of DC breakdown in ultra high vacuum are carried out in parallel with high power RF tests. From the point of view of saturation breakdown field the best material tested so far is stainless steel, followed by titanium. Copper shows a four times weaker breakdown field than stainless steel. The results indicate clearly that the breakdown events are initiated by field emission current and that the breakdown field is limited by the cathode. In analogy to RF, the breakdown probability has been measured in DC and the data show similar behaviour as a function of electric field.

  20. DC attenuation meter

    DOEpatents

    Hargrove, Douglas L.

    2004-09-14

    A portable, hand-held meter used to measure direct current (DC) attenuation in low impedance electrical signal cables and signal attenuators. A DC voltage is applied to the signal input of the cable and feedback to the control circuit through the signal cable and attenuators. The control circuit adjusts the applied voltage to the cable until the feedback voltage equals the reference voltage. The "units" of applied voltage required at the cable input is the system attenuation value of the cable and attenuators, which makes this meter unique. The meter may be used to calibrate data signal cables, attenuators, and cable-attenuator assemblies.

  1. Differential Mortality of Male Spectacled Eiders (Somateria fischeri) and King Eiders (Somateria spectabilis) Subsequent to Anesthesia with Propofol, Bupivacaine, and Ketoprofen

    USGS Publications Warehouse

    Mulcahy, D.M.; Tuomi, P.; Larsen, R.S.

    2003-01-01

    Twenty free-ranging spectacled eiders (Somateria fischeri; 10 male, 10 female), 11 free-ranging king eiders (Somateria spectabilis; 6 male, 5 female), and 20 female common eiders (Somateria mollissima) were anesthetized with propofol, bupivacaine, and ketoprofen for the surgical implantation of satellite transmitters. Propofol was given to induce and maintain anesthesia (mean total dose, 26.2-45.6 mg/kg IV), bupivacaine (2-10 mg/kg SC) was infused into the incision site for local analgesia, and ketoprofen (2-5 mg/kg IM) was given at the time of surgery for postoperative analgesia. Four of 10 male spectacled eiders and 5 of 6 male king eiders died within 1-4 days after surgery. None of the female spectacled or common eiders and only 1 of the 5 female king eiders died during the same postoperative period. Histopathologic findings in 2 dead male king eiders were severe renal tubular necrosis, acute rhabdomyolysis, and mild visceral gout. Necropsy findings in 3 other dead male king eiders were consistent with visceral gout. We suspect that the perioperative use of ketoprofen caused lethal renal damage in the male eiders. Male eiders may be more susceptible to renal damage than females because of behavioral differences during their short stay on land in mating season. The combination of propofol, bupivacaine, and ketoprofen should not be used to anesthetize free-ranging male eiders, and nonsteroidal anti-inflammatory drugs should not be used perioperatively in any bird that may be predisposed to renal insufficiency.

  2. DYLOS DC110

    EPA Science Inventory

    The Dylos DC1100 air quality monitor measures particulate matter (PM) to provide a continuous assessment of indoor air quality. The unit counts particles in two size ranges: large and small. According to the manufacturer, large particles have diameters between 2.5 and 10 micromet...

  3. DC arc weld starter

    DOEpatents

    Campiotti, Richard H.; Hopwood, James E.

    1990-01-01

    A system for starting an arc for welding uses three DC power supplies, a high voltage supply for initiating the arc, an intermediate voltage supply for sustaining the arc, and a low voltage welding supply directly connected across the gap after the high voltage supply is disconnected.

  4. DC-DC powering for the CMS pixel upgrade

    NASA Astrophysics Data System (ADS)

    Feld, Lutz; Fleck, Martin; Friedrichs, Marcel; Hensch, Richard; Karpinski, Waclaw; Klein, Katja; Rittich, David; Sammet, Jan; Wlochal, Michael

    2013-12-01

    The CMS experiment plans to replace its silicon pixel detector with a new one with improved rate capability and an additional detection layer at the end of 2016. In order to cope with the increased number of detector modules the new pixel detector will be powered via DC-DC converters close to the sensitive detector volume. This paper reviews the DC-DC powering scheme and reports on the ongoing R&D program to develop converters for the pixel upgrade. Design choices are discussed and results from the electrical and thermal characterisation of converter prototypes are shown. An emphasis is put on system tests with up to 24 converters. The performance of pixel modules powered by DC-DC converters is compared to conventional powering. The integration of the DC-DC powering scheme into the pixel detector is described and system design issues are reviewed.

  5. Early Oscillation Detection for DC/DC Converter Fault Diagnosis

    NASA Technical Reports Server (NTRS)

    Wang, Bright L.

    2011-01-01

    The electrical power system of a spacecraft plays a very critical role for space mission success. Such a modern power system may contain numerous hybrid DC/DC converters both inside the power system electronics (PSE) units and onboard most of the flight electronics modules. One of the faulty conditions for DC/DC converter that poses serious threats to mission safety is the random occurrence of oscillation related to inherent instability characteristics of the DC/DC converters and design deficiency of the power systems. To ensure the highest reliability of the power system, oscillations in any form shall be promptly detected during part level testing, system integration tests, flight health monitoring, and on-board fault diagnosis. The popular gain/phase margin analysis method is capable of predicting stability levels of DC/DC converters, but it is limited only to verification of designs and to part-level testing on some of the models. This method has to inject noise signals into the control loop circuitry as required, thus, interrupts the DC/DC converter's normal operation and increases risks of degrading and damaging the flight unit. A novel technique to detect oscillations at early stage for flight hybrid DC/DC converters was developed.

  6. Contingent post-closure plan, hazardous waste management units at selected maintenance facilities, US Army National Training Center, Fort Irwin, California

    SciTech Connect

    Not Available

    1992-01-01

    The National Training Center (NTC) at Fort Irwin, California, is a US Army training installation that provides tactical experience for battalion/task forces and squadrons in a mid- to high-intensity combat scenario. Through joint exercises with US Air Force and other services, the NTC also provides a data source for improvements of training doctrines, organization, and equipment. To meet the training and operational needs of the NTC, several maintenance facilities provide general and direct support for mechanical devices, equipment, and vehicles. Maintenance products used at these facilities include fuels, petroleum-based oils, lubricating grease, various degreasing solvents, antifreeze (ethylene glycol), transmission fluid, brake fluid, and hydraulic oil. Used or spent petroleum-based products generated at the maintenance facilities are temporarily accumulated in underground storage tanks (USTs), collected by the NTC hazardous waste management contractor (HAZCO), and stored at the Petroleum, Oil, and Lubricant (POL) Storage Facility, Building 630, until shipped off site to be recovered, reused, and/or reclaimed. Spent degreasing solvents and other hazardous wastes are containerized and stored on-base for up to 90 days at the NTC's Hazardous Waste Storage Facility, Building 703. The US Environmental Protection Agency (EPA) performed an inspection and reviewed the hazardous waste management operations of the NTC. Inspections indicated that the NTC had violated one or more requirements of Subtitle C of the Resource Conservation and Recovery Act (RCRA) and as a result of these violations was issued a Notice of Noncompliance, Notice of Necessity for Conference, and Proposed Compliance Schedule (NON) dated October 13, 1989. The following post-closure plan is the compliance-based approach for the NTC to respond to the regulatory violations cited in the NON.

  7. Contingent post-closure plan, hazardous waste management units at selected maintenance facilities, US Army National Training Center, Fort Irwin, California

    SciTech Connect

    Not Available

    1992-01-01

    The National Training Center (NTC) at Fort Irwin, California, is a US Army training installation that provides tactical experience for battalion/task forces and squadrons in a mid- to high-intensity combat scenario. Through joint exercises with US Air Force and other services, the NTC also provides a data source for improvements of training doctrines, organization, and equipment. To meet the training and operational needs of the NTC, several maintenance facilities provide general and direct support for mechanical devices, equipment, and vehicles. Maintenance products used at these facilities include fuels, petroleum-based oils, lubricating grease, various degreasing solvents, antifreeze (ethylene glycol), transmission fluid, brake fluid, and hydraulic oil. Used or spent petroleum-based products generated at the maintenance facilities are temporarily accumulated in underground storage tanks (USTs), collected by the NTC hazardous waste management contractor (HAZCO), and stored at the Petroleum, Oil, and Lubricant (POL) Storage Facility, Building 630, until shipped off site to be recovered, reused, and/or reclaimed. Spent degreasing solvents and other hazardous wastes are containerized and stored on-base for up to 90 days at the NTC`s Hazardous Waste Storage Facility, Building 703. The US Environmental Protection Agency (EPA) performed an inspection and reviewed the hazardous waste management operations of the NTC. Inspections indicated that the NTC had violated one or more requirements of Subtitle C of the Resource Conservation and Recovery Act (RCRA) and as a result of these violations was issued a Notice of Noncompliance, Notice of Necessity for Conference, and Proposed Compliance Schedule (NON) dated October 13, 1989. The following post-closure plan is the compliance-based approach for the NTC to respond to the regulatory violations cited in the NON.

  8. Auxiliary resonant DC tank converter

    DOEpatents

    Peng, Fang Z.

    2000-01-01

    An auxiliary resonant dc tank (ARDCT) converter is provided for achieving soft-switching in a power converter. An ARDCT circuit is coupled directly across a dc bus to the inverter to generate a resonant dc bus voltage, including upper and lower resonant capacitors connected in series as a resonant leg, first and second dc tank capacitors connected in series as a tank leg, and an auxiliary resonant circuit comprising a series combination of a resonant inductor and a pair of auxiliary switching devices. The ARDCT circuit further includes first clamping means for holding the resonant dc bus voltage to the dc tank voltage of the tank leg, and second clamping means for clamping the resonant dc bus voltage to zero during a resonant period. The ARDCT circuit resonantly brings the dc bus voltage to zero in order to provide a zero-voltage switching opportunity for the inverter, then quickly rebounds the dc bus voltage back to the dc tank voltage after the inverter changes state. The auxiliary switching devices are turned on and off under zero-current conditions. The ARDCT circuit only absorbs ripples of the inverter dc bus current, thus having less current stress. In addition, since the ARDCT circuit is coupled in parallel with the dc power supply and the inverter for merely assisting soft-switching of the inverter without participating in real dc power transmission and power conversion, malfunction and failure of the tank circuit will not affect the functional operation of the inverter; thus a highly reliable converter system is expected.

  9. High performance dc-dc conversion with voltage multipliers

    NASA Technical Reports Server (NTRS)

    Harrigill, W. T.; Myers, I. T.

    1974-01-01

    The voltage multipliers using capacitors and diodes first developed by Cockcroft and Walton in 1932 were reexamined in terms of state of the art fast switching transistors and diodes, and high energy density capacitors. Because of component improvements, the voltage multiplier, used without a transformer, now appears superior in weight to systems now in use for dc-dc conversion. An experimental 100-watt 1000-volt dc-dc converter operating at 100 kHz was built, with a component weight of about 1 kg/kW. Calculated and measured values of output voltage and efficiency agreed within experimental error.

  10. Improved DC Gun Insulator

    SciTech Connect

    M.L. Neubauer, K.B. Beard, R. Sah, C. Hernandez-Garcia, G. Neil

    2009-05-01

    Many user facilities such as synchrotron light sources and free electron lasers require accelerating structures that support electric fields of 10-100 MV/m, especially at the start of the accelerator chain where ceramic insulators are used for very high gradient DC guns. These insulators are difficult to manufacture, require long commissioning times, and have poor reliability, in part because energetic electrons bury themselves in the ceramic, creating a buildup of charge and causing eventual puncture. A novel ceramic manufacturing process is proposed. It will incorporate bulk resistivity in the region where it is needed to bleed off accumulated charge caused by highly energetic electrons. This process will be optimized to provide an appropriate gradient in bulk resistivity from the vacuum side to the air side of the HV standoff ceramic cylinder. A computer model will be used to determine the optimum cylinder dimensions and required resistivity gradient for an example RF gun application. A ceramic material example with resistivity gradient appropriate for use as a DC gun insulator will be fabricated by glazing using doping compounds and tested.

  11. In vitro evaluation of the schistosomicidal effect of the extracts, fractions and major 3-hydroxy-2,6-dialkyl-substituted piperidine alkaloids from the flowers of Senna spectabilis (Fabaceae).

    PubMed

    de Castro, Andreísa Teixeira; Castro, Aline Pereira; Silva, Matheus Siqueira; de Souza, Isabella Maria Monteiro; Martins-Souza, Raquel Lopes; Chagas-Paula, Daniela Aparecida; Coelho, Luiz Felipe Leomil; da Silva Bolzani, Vanderlan; Pivatto, Marcos; Viegas, Claudio; Marques, Marcos José

    2016-09-01

    In this work, we present the in vitro schistosomicidal activity evaluation of the most active dichloromethane fraction (FDm) (ED50=83.5μg/mL) and of a mixture of the major alkaloids ((-)-cassine/(-)-spectaline, C/E) (ED50=37.4μg/mL) from the flowers of Senna spectabilis against adult worms and cercariae. We also demonstrate other toxic effects including paralysis of the adult worms, inhibition of the secretory activity, tegument lesions and cercaricidal activity. In the association test of Praziquantel (PZQ)-C/E, we observed up to 80% mortality of Schistosoma mansoni in comparison to PZQ monotherapy. Due to the diversity of the toxic effects, the schistosomicidal activity of C/E is likely a result of a multitarget mechanism involving the tegument, secretory system and neuromotor action. PMID:27491706

  12. Dc-To-Dc Converter Uses Reverse Conduction Of MOSFET's

    NASA Technical Reports Server (NTRS)

    Gruber, Robert P.; Gott, Robert W.

    1991-01-01

    In modified high-power, phase-controlled, full-bridge, pulse-width-modulated dc-to-dc converters, switching devices power metal oxide/semiconductor field-effect transistors (MOSFET's). Decreases dissipation of power during switching by eliminating approximately 0.7-V forward voltage drop in anti-parallel diodes. Energy-conversion efficiency increased.

  13. Efficient Design in a DC to DC Converter Unit

    NASA Technical Reports Server (NTRS)

    Bruemmer, Joel E.; Williams, Fitch R.; Schmitz, Gregory V.

    2002-01-01

    Space Flight hardware requires high power conversion efficiencies due to limited power availability and weight penalties of cooling systems. The International Space Station (ISS) Electric Power System (EPS) DC-DC Converter Unit (DDCU) power converter is no exception. This paper explores the design methods and tradeoffs that were utilized to accomplish high efficiency in the DDCU. An isolating DC to DC converter was selected for the ISS power system because of requirements for separate primary and secondary grounds and for a well-regulated secondary output voltage derived from a widely varying input voltage. A flyback-current-fed push-pull topology or improved Weinberg circuit was chosen for this converter because of its potential for high efficiency and reliability. To enhance efficiency, a non-dissipative snubber circuit for the very-low-Rds-on Field Effect Transistors (FETs) was utilized, redistributing the energy that could be wasted during the switching cycle of the power FETs. A unique, low-impedance connection system was utilized to improve contact resistance over a bolted connection. For improved consistency in performance and to lower internal wiring inductance and losses a planar bus system is employed. All of these choices contributed to the design of a 6.25 KW regulated dc to dc converter that is 95 percent efficient. The methodology used in the design of this DC to DC Converter Unit may be directly applicable to other systems that require a conservative approach to efficient power conversion and distribution.

  14. A Plasma-Based DC-DC Electrical Transformer

    NASA Astrophysics Data System (ADS)

    Nebel, Richard; Finn, John

    2013-10-01

    Previous work has indicated that it may be possible to make DC-DC electrical transformers using plasmas. The mechanism is an MHD electromagnetic relaxation process induced by helical electrodes. This process is now being tested on the Bismark device at Tibbar Technologies.

  15. A DC Transformer

    NASA Technical Reports Server (NTRS)

    Youngquist, Robert C.; Ihlefeld, Curtis M.; Starr, Stanley O.

    2013-01-01

    A component level dc transformer is described in which no alternating currents or voltages are present. It operates by combining features of a homopolar motor and a homopolar generator, both de devices, such that the output voltage of a de power supply can be stepped up (or down) with a corresponding step down (or up) in current. The basic theory for this device is developed, performance predictions are made, and the results from a small prototype are presented. Based on demonstrated technology in the literature, this de transformer should be scalable to low megawatt levels, but it is more suited to high current than high voltage applications. Significant development would be required before it could achieve the kilovolt levels needed for de power transmission.

  16. Early Oscillation Detection Technique for Hybrid DC/DC Converters

    NASA Technical Reports Server (NTRS)

    Wang, Bright L.

    2011-01-01

    Oscillation or instability is a situation that must be avoided for reliable hybrid DC/DC converters. A real-time electronics measurement technique was developed to detect catastrophic oscillations at early stages for hybrid DC/DC converters. It is capable of identifying low-level oscillation and determining the degree of the oscillation at a unique frequency for every individual model of the converters without disturbing their normal operations. This technique is specially developed for space-used hybrid DC/DC converters, but it is also suitable for most of commercial and military switching-mode power supplies. This is a weak-electronic-signal detection technique to detect hybrid DC/DC converter oscillation presented as a specific noise signal at power input pins. It is based on principles of feedback control loop oscillation and RF signal modulations, and is realized by using signal power spectral analysis. On the power spectrum, a channel power amplitude at characteristic frequency (CPcf) and a channel power amplitude at switching frequency (CPsw) are chosen as oscillation level indicators. If the converter is stable, the CPcf is a very small pulse and the CPsw is a larger, clear, single pulse. At early stage of oscillation, the CPcf increases to a certain level and the CPsw shows a small pair of sideband pulses around it. If the converter oscillates, the CPcf reaches to a higher level and the CPsw shows more high-level sideband pulses. A comprehensive stability index (CSI) is adopted as a quantitative measure to accurately assign a degree of stability to a specific DC/DC converter. The CSI is a ratio of normal and abnormal power spectral density, and can be calculated using specified and measured CPcf and CPsw data. The novel and unique feature of this technique is the use of power channel amplitudes at characteristic frequency and switching frequency to evaluate stability and identify oscillations at an early stage without interfering with a DC/DC converter s

  17. Triple voltage dc-to-dc converter and method

    SciTech Connect

    Su, Gui-Jia

    2008-08-05

    A circuit and method of providing three dc voltage buses and transforming power between a low voltage dc converter and a high voltage dc converter, by coupling a primary dc power circuit and a secondary dc power circuit through an isolation transformer; providing the gating signals to power semiconductor switches in the primary and secondary circuits to control power flow between the primary and secondary circuits and by controlling a phase shift between the primary voltage and the secondary voltage. The primary dc power circuit and the secondary dc power circuit each further comprising at least two tank capacitances arranged in series as a tank leg, at least two resonant switching devices arranged in series with each other and arranged in parallel with the tank leg, and at least one voltage source arranged in parallel with the tank leg and the resonant switching devices, said resonant switching devices including power semiconductor switches that are operated by gating signals. Additional embodiments having a center-tapped battery on the low voltage side and a plurality of modules on both the low voltage side and the high voltage side are also disclosed for the purpose of reducing ripple current and for reducing the size of the components.

  18. Bi-Directional DC-DC Converter for PHEV Applications

    SciTech Connect

    Abas Goodarzi

    2011-01-31

    Plug-In Hybrid Electric Vehicles (PHEV) require high power density energy storage system (ESS) for hybrid operation and high energy density ESS for Electric Vehicle (EV) mode range. However, ESS technologies to maximize power density and energy density simultaneously are not commercially feasible. The use of bi-directional DC-DC converter allows use of multiple energy storage, and the flexible DC-link voltages can enhance the system efficiency and reduce component sizing. This will improve fuel consumption, increase the EV mode range, reduce the total weight, reduce battery initial and life cycle cost, and provide flexibility in system design.

  19. DC-Compensated Current Transformer.

    PubMed

    Ripka, Pavel; Draxler, Karel; Styblíková, Renata

    2016-01-20

    Instrument current transformers (CTs) measure AC currents. The DC component in the measured current can saturate the transformer and cause gross error. We use fluxgate detection and digital feedback compensation of the DC flux to suppress the overall error to 0.15%. This concept can be used not only for high-end CTs with a nanocrystalline core, but it also works for low-cost CTs with FeSi cores. The method described here allows simultaneous measurements of the DC current component.

  20. DC-Compensated Current Transformer.

    PubMed

    Ripka, Pavel; Draxler, Karel; Styblíková, Renata

    2016-01-01

    Instrument current transformers (CTs) measure AC currents. The DC component in the measured current can saturate the transformer and cause gross error. We use fluxgate detection and digital feedback compensation of the DC flux to suppress the overall error to 0.15%. This concept can be used not only for high-end CTs with a nanocrystalline core, but it also works for low-cost CTs with FeSi cores. The method described here allows simultaneous measurements of the DC current component. PMID:26805830

  1. Digital Control Technologies for Modular DC-DC Converters

    NASA Technical Reports Server (NTRS)

    Button, Robert M.; Kascak, Peter E.; Lebron-Velilla, Ramon

    2002-01-01

    Recent trends in aerospace Power Management and Distribution (PMAD) systems focus on using commercial off-the-shelf (COTS) components as standard building blocks. This move to more modular designs has been driven by a desire to reduce costs and development times, but is also due to the impressive power density and efficiency numbers achieved by today's commercial DC-DC converters. However, the PMAD designer quickly learns of the hidden "costs" of using COTS converters. The most significant cost is the required addition of external input filters to meet strict electromagnetic interference (MIAMI) requirements for space systems. In fact, the high power density numbers achieved by the commercial manufacturers are greatly due to the lack of necessary input filters included in the COTS module. The NASA Glenn Research Center is currently pursuing a digital control technology that addresses this problem with modular DC-DC converters. This paper presents the digital control technologies that have been developed to greatly reduce the input filter requirements for paralleled, modular DC-DC converters. Initial test result show that the input filter's inductor size was reduced by 75 percent, and the capacitor size was reduced by 94 percent while maintaining the same power quality specifications.

  2. DC superconducting fault current limiter

    NASA Astrophysics Data System (ADS)

    Tixador, P.; Villard, C.; Cointe, Y.

    2006-03-01

    There is a lack of satisfying solutions for fault currents using conventional technologies, especially in DC networks, where a superconducting fault current limiter could play a very important part. DC networks bring a lot of advantages when compared to traditional AC ones, in particular within the context of the liberalization of the electric market. Under normal operation in a DC network, the losses in the superconducting element are nearly zero and only a small, i.e. a low cost, refrigeration system is then required. The absence of zero crossing of a DC fault current favourably accelerates the normal zone propagation. The very high current slope at the time of the short circuit in a DC grid is another favourable parameter. The material used for the experiments is YBCO deposited on Al2O3 as well as YBCO coated conductors. The DC limitation experiments are compared to AC ones at different frequencies (50-2000 Hz). Careful attention is paid to the quench homogenization, which is one of the key issues for an SC FCL. The University of Geneva has proposed constrictions. We have investigated an operating temperature higher than 77 K. As for YBCO bulk, an operation closer to the critical temperature brings a highly improved homogeneity in the electric field development. The material can then absorb large energies without degradation. We present tests at various temperatures. These promising results are to be confirmed over long lengths.

  3. 75 FR 36298 - Airworthiness Directives; McDonnell Douglas Corporation Model DC-8-31, DC-8-32, DC-8-33, DC-8-41...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-06-25

    ...-09-04, Amendment 39-15484 (73 FR 21523, April 22, 2008), for all Model DC-8-31, DC-8-32, DC-8-33, DC... ``significant rule'' under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and 3... removing Amendment 39-15484 (73 FR 21523, April 22, 2008) and adding the following new AD:...

  4. Transformerless dc-to-dc converters with large conversion ratios

    NASA Astrophysics Data System (ADS)

    Middlebrook, R. D.

    1988-10-01

    A novel switching dc-dc converter is introduced in which large voltage step-down ratios can be achieved without a very small duty ratio and without a transformer. The circuit is an extension of the Cuk converter to incorporate a multistage capacitor divider. A particularly suitable application would be a 50-V to 5-V converter in which dc isolation is not required. The absence of a transformer and the larger duty ratio permit operation at a high switching frequency and make the circuit amenable to partial integration and hybrid construction techniques. An experimental 50-W three-stage voltage-divider Cuk converter converts 50 V to 5 V at 500 kHz, with efficiency higher than for a basic Cuk converter operated at the same conditions. A corresponding voltage-multiplier Cuk converter is described, as well as dual buck-boost-derived step-down and step-up converters.

  5. Light-weight DC to very high voltage DC converter

    DOEpatents

    Druce, R.L.; Kirbie, H.C.; Newton, M.A.

    1998-06-30

    A DC-DC converter capable of generating outputs of 100 KV without a transformer comprises a silicon opening switch (SOS) diode connected to allow a charging current from a capacitor to flow into an inductor. When a specified amount of charge has flowed through the SOS diode, it opens up abruptly; and the consequential collapsing field of the inductor causes a voltage and current reversal that is steered into a load capacitor by an output diode. A switch across the series combination of the capacitor, inductor, and SOS diode closes to periodically reset the SOS diode by inducing a forward-biased current. 1 fig.

  6. Light-weight DC to very high voltage DC converter

    DOEpatents

    Druce, Robert L.; Kirbie, Hugh C.; Newton, Mark A.

    1998-01-01

    A DC-DC converter capable of generating outputs of 100 KV without a transformer comprises a silicon opening switch (SOS) diode connected to allow a charging current from a capacitor to flow into an inductor. When a specified amount of charge has flowed through the SOS diode, it opens up abruptly; and the consequential collapsing field of the inductor causes a voltage and current reversal that is steered into a load capacitor by an output diode. A switch across the series combination of the capacitor, inductor, and SOS diode closes to periodically reset the SOS diode by inducing a forward-biased current.

  7. Commercial Of-The Shelf DC/DC Converter

    NASA Astrophysics Data System (ADS)

    Denzinger, W.; Baumel, S.

    2011-10-01

    A commercial of-the-shelf (COTS) DC/DC converter for the supply of digital electronics on board of spacecraft has been developed with special emphasis on: *Low cost Readily available *Easy manufacturing *No use of ITAR listed EEE parts like rad-hard mosfets *Minimum number of rad-hard digital and analog IC's *Design tolerance against SEE by appropriate filtering The study was supported by the European Space Agency (ESA) under the contract number 21729/08/NL7LvH.

  8. Low dose failures of hardened DC-DC power converters

    NASA Technical Reports Server (NTRS)

    Lehman, J.; Yui, C.; Rax, B. G.; Miyahira, T. F.; Weideman, M.; Schrick, P.; Swift, G. M.; Johnston, A. H.

    2002-01-01

    Box-level total dose testing of the FOG (Fiber Optic Gyro) by IXSEA at ESA's GammabeamFacility were abruptly terminated at 8krad (Si) due to catastrophic failure (complete shutdown). This was unexpected because all components within the gyro were supposedly radiation tolerant. Further testing showed that the components responsible for the failure were two DC-DC converters, manufactured by Interpoint, that stopped regulating shortly before shutdown. This paper summarizes diagnostic test results for the converters to determine the underlying cause of the unexpected failure at low levels of radiation.

  9. 14 CFR 93.339 - Requirements for operating in the DC SFRA, including the DC FRZ.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ..., including the DC FRZ. (a) Except as provided in paragraphs (b) and (c) of this section and in § 93.345, or... operating within the DC SFRA; (5) For VFR operations, the pilot must file and activate a DC FRZ or DC SFRA..., out of, or through the Washington, DC Tri-Area Class B Airspace Area, the pilot receives a...

  10. 14 CFR 93.339 - Requirements for operating in the DC SFRA, including the DC FRZ.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ..., including the DC FRZ. (a) Except as provided in paragraphs (b) and (c) of this section and in § 93.345, or... operating within the DC SFRA; (5) For VFR operations, the pilot must file and activate a DC FRZ or DC SFRA..., out of, or through the Washington, DC Tri-Area Class B Airspace Area, the pilot receives a...

  11. 14 CFR 93.339 - Requirements for operating in the DC SFRA, including the DC FRZ.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ..., including the DC FRZ. (a) Except as provided in paragraphs (b) and (c) of this section and in § 93.345, or... operating within the DC SFRA; (5) For VFR operations, the pilot must file and activate a DC FRZ or DC SFRA..., out of, or through the Washington, DC Tri-Area Class B Airspace Area, the pilot receives a...

  12. 14 CFR 93.339 - Requirements for operating in the DC SFRA, including the DC FRZ.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ..., including the DC FRZ. (a) Except as provided in paragraphs (b) and (c) of this section and in § 93.345, or... operating within the DC SFRA; (5) For VFR operations, the pilot must file and activate a DC FRZ or DC SFRA..., out of, or through the Washington, DC Tri-Area Class B Airspace Area, the pilot receives a...

  13. An integrated dc SQUID cascade

    SciTech Connect

    Davidson, A.

    1983-05-01

    An integrated tunnel junction dc SQUID cascade has been built and some of its operating characteristics measured. It is shown for the first time that good modulation can be achieved with a remote termination for the tunnel junction shunts. Response time of one of the SQUID's in the cascade was measured to be better than 5 nanoseconds. Maintenance of this high speed is an advantage of the cascade arrangement over other schemes for matching and reading-out dc tunnel junction SQUID's. True cascade operation was not obtained, due to coupling of Josephson oscillations from the first stage of the cascade to the second.

  14. AC and DC power transmission

    SciTech Connect

    Not Available

    1985-01-01

    The technical and economic assessment of AC and DC transmission systems; long distance transmission, cable transmission, system inter-connection, voltage support, reactive compensation, stabilisation of systems; parallel operation of DC links with AC systems; comparison between alternatives for particular schemes. Design and application equipment: design, testing and application of equipment for HVDC, series and shunt static compensated AC schemes, including associated controls. Installations: overall design of stations and conductor arrangements for HVDC, series and shunt static AC schemes including insulation co-ordination. System analysis and modelling.

  15. Piezometer completion report for borehole cluster sites DC-19, DC-20, and DC-22

    SciTech Connect

    Jackson, R.L.; Diediker, L.D.; Ledgerwood, R.K.; Veatch, M.D.

    1984-07-01

    This report describes the design and installation of multi-level piezometers at borehole cluster sites DC-19, DC-20 and DC-22. The network of borehole cluster sites will provide facilities for multi-level water-level monitoring across the RRL for piezometer baseline monitoring and for large-scale hydraulic stress testing. These groundwater-monitoring facilities were installed between August 1983 and March 1984. Three series of piezometer nests (A-, C- and D-series) were installed in nine hydrogeologic units (monitoring horizons) within the Columbia River Basalt Group at each borehole cluster site. In addition to the piezometer facilities, a B-series pumping well was installed at borehole cluster sites DC-20 and DC-22. The A-series piezometer nest monitors the basal Ringold sediments and the Rattlesnake Ridge interbed. The C-series piezometer nests monitors the six deepest horizons, which are in increasing depth, the Priest Rapids interflow, Sentinel Gap flow top, Ginkgo flow top, Rocky Coulee flow top, Cohassett flow top and Umtanum flow top. The D-series piezometer monitors the Mabton interbed. The B-series pumping well was completed in the Priest Rapids interflow. 21 refs., 6 figs., 6 tabs.

  16. A priori and a posteriori approaches for finding genes of evolutionary interest in non-model species: osmoregulatory genes in the kidney transcriptome of the desert rodent Dipodomys spectabilis (banner-tailed kangaroo rat).

    PubMed

    Marra, Nicholas J; Eo, Soo Hyung; Hale, Matthew C; Waser, Peter M; DeWoody, J Andrew

    2012-12-01

    One common goal in evolutionary biology is the identification of genes underlying adaptive traits of evolutionary interest. Recently next-generation sequencing techniques have greatly facilitated such evolutionary studies in species otherwise depauperate of genomic resources. Kangaroo rats (Dipodomys sp.) serve as exemplars of adaptation in that they inhabit extremely arid environments, yet require no drinking water because of ultra-efficient kidney function and osmoregulation. As a basis for identifying water conservation genes in kangaroo rats, we conducted a priori bioinformatics searches in model rodents (Mus musculus and Rattus norvegicus) to identify candidate genes with known or suspected osmoregulatory function. We then obtained 446,758 reads via 454 pyrosequencing to characterize genes expressed in the kidney of banner-tailed kangaroo rats (Dipodomys spectabilis). We also determined candidates a posteriori by identifying genes that were overexpressed in the kidney. The kangaroo rat sequences revealed nine different a priori candidate genes predicted from our Mus and Rattus searches, as well as 32 a posteriori candidate genes that were overexpressed in kidney. Mutations in two of these genes, Slc12a1 and Slc12a3, cause human renal diseases that result in the inability to concentrate urine. These genes are likely key determinants of physiological water conservation in desert rodents.

  17. Switching coordination of distributed dc-dc converters for highly efficient photovoltaic power plants

    DOEpatents

    Agamy, Mohammed; Elasser, Ahmed; Sabate, Juan Antonio; Galbraith, Anthony William; Harfman Todorovic, Maja

    2014-09-09

    A distributed photovoltaic (PV) power plant includes a plurality of distributed dc-dc converters. The dc-dc converters are configured to switch in coordination with one another such that at least one dc-dc converter transfers power to a common dc-bus based upon the total system power available from one or more corresponding strings of PV modules. Due to the coordinated switching of the dc-dc converters, each dc-dc converter transferring power to the common dc-bus continues to operate within its optimal efficiency range as well as to optimize the maximum power point tracking in order to increase the energy yield of the PV power plant.

  18. DC coupled Doppler radar physiological monitor.

    PubMed

    Zhao, Xi; Song, Chenyan; Lubecke, Victor; Boric-Lubecke, Olga

    2011-01-01

    One of the challenges in Doppler radar systems for physiological monitoring is a large DC offset in baseband outputs. Typically, AC coupling is used to eliminate this DC offset. Since the physiological signals of interest include frequency content near DC, it is not desirable to simply use AC coupling on the radar outputs. While AC coupling effectively removes DC offset, it also introduces a large time delay and distortion. This paper presents the first DC coupled IQ demodulator printed circuit board (PCB) design and measurements. The DC coupling is achieved by using a mixer with high LO to RF port isolation, resulting in a very low radar DC offset on the order of mV. The DC coupled signals from the PCB radar system were successfully detected with significant LNA gain without saturation. Compared to the AC coupled results, the DC coupled results show great advantages of less signal distortion and more accurate rate estimation.

  19. DC coupled Doppler radar physiological monitor.

    PubMed

    Zhao, Xi; Song, Chenyan; Lubecke, Victor; Boric-Lubecke, Olga

    2011-01-01

    One of the challenges in Doppler radar systems for physiological monitoring is a large DC offset in baseband outputs. Typically, AC coupling is used to eliminate this DC offset. Since the physiological signals of interest include frequency content near DC, it is not desirable to simply use AC coupling on the radar outputs. While AC coupling effectively removes DC offset, it also introduces a large time delay and distortion. This paper presents the first DC coupled IQ demodulator printed circuit board (PCB) design and measurements. The DC coupling is achieved by using a mixer with high LO to RF port isolation, resulting in a very low radar DC offset on the order of mV. The DC coupled signals from the PCB radar system were successfully detected with significant LNA gain without saturation. Compared to the AC coupled results, the DC coupled results show great advantages of less signal distortion and more accurate rate estimation. PMID:22254704

  20. DC-Powered Jumping Ring

    ERIC Educational Resources Information Center

    Jeffery, Rondo N.; Farhang, Amiri

    2016-01-01

    The classroom jumping ring demonstration is nearly always performed using alternating current (AC), in which the ring jumps or flies off the extended iron core when the switch is closed. The ring jumps higher when cooled with liquid nitrogen (LN2). We have performed experiments using DC to power the solenoid and find similarities and significant…

  1. Experiments with a DC Motor

    ERIC Educational Resources Information Center

    Kraftmakher, Yaakov

    2010-01-01

    Experiments with an electric motor provide good opportunity to demonstrate some basic laws of electricity and magnetism. The aim of the experiments with a low-power dc motor is to show how the motor approaches its steady rotation and how its torque, mechanical power and efficiency depend on the rotation velocity. The tight relationship between the…

  2. Identification of cDC1- and cDC2-committed DC progenitors reveals early lineage priming at the common DC progenitor stage in the bone marrow.

    PubMed

    Schlitzer, Andreas; Sivakamasundari, V; Chen, Jinmiao; Sumatoh, Hermi Rizal Bin; Schreuder, Jaring; Lum, Josephine; Malleret, Benoit; Zhang, Sanqian; Larbi, Anis; Zolezzi, Francesca; Renia, Laurent; Poidinger, Michael; Naik, Shalin; Newell, Evan W; Robson, Paul; Ginhoux, Florent

    2015-07-01

    Mouse conventional dendritic cells (cDCs) can be classified into two functionally distinct lineages: the CD8α(+) (CD103(+)) cDC1 lineage, and the CD11b(+) cDC2 lineage. cDCs arise from a cascade of bone marrow (BM) DC-committed progenitor cells that include the common DC progenitors (CDPs) and pre-DCs, which exit the BM and seed peripheral tissues before differentiating locally into mature cDCs. Where and when commitment to the cDC1 or cDC2 lineage occurs remains poorly understood. Here we found that transcriptional signatures of the cDC1 and cDC2 lineages became evident at the single-cell level from the CDP stage. We also identified Siglec-H and Ly6C as lineage markers that distinguished pre-DC subpopulations committed to the cDC1 lineage (Siglec-H(-)Ly6C(-) pre-DCs) or cDC2 lineage (Siglec-H(-)Ly6C(+) pre-DCs). Our results indicate that commitment to the cDC1 or cDC2 lineage occurs in the BM and not in the periphery.

  3. DC to DC power converters and methods of controlling the same

    DOEpatents

    Steigerwald, Robert Louis; Elasser, Ahmed; Sabate, Juan Antonio; Todorovic, Maja Harfman; Agamy, Mohammed

    2012-12-11

    A power generation system configured to provide direct current (DC) power to a DC link is described. The system includes a first power generation unit configured to output DC power. The system also includes a first DC to DC converter comprising an input section and an output section. The output section of the first DC to DC converter is coupled in series with the first power generation unit. The first DC to DC converter is configured to process a first portion of the DC power output by the first power generation unit and to provide an unprocessed second portion of the DC power output of the first power generation unit to the output section.

  4. Dilation and Curettage (D&C)

    MedlinePlus

    ... Advocacy For Patients About ACOG Dilation and Curettage (D&C) Home For Patients Search FAQs Dilation and ... FAQ062, February 2016 PDF Format Dilation and Curettage (D&C) Special Procedures What is dilation and curettage ( ...

  5. Mesoscopic electronics beyond DC transport

    NASA Astrophysics Data System (ADS)

    di Carlo, Leonardo

    Since the inception of mesoscopic electronics in the 1980's, direct current (dc) measurements have underpinned experiments in quantum transport. Novel techniques complementing dc transport are becoming paramount to new developments in mesoscopic electronics, particularly as the road is paved toward quantum information processing. This thesis describes seven experiments on GaAs/AlGaAs and graphene nanostructures unified by experimental techniques going beyond traditional dc transport. Firstly, dc current induced by microwave radiation applied to an open chaotic quantum dot is investigated. Asymmetry of mesoscopic fluctuations of induced current in perpendicular magnetic field is established as a tool for separating the quantum photovoltaic effect from classical rectification. A differential charge sensing technique is next developed using integrated quantum point contacts to resolve the spatial distribution of charge inside a double quantum clot. An accurate method for determining interdot tunnel coupling and electron temperature using charge sensing is demonstrated. A two-channel system for detecting current noise in mesoscopic conductors is developed, enabling four experiments where shot noise probes transmission properties not available in dc transport and Johnson noise serves as an electron thermometer. Suppressed shot noise is observed in quantum point contacts at zero parallel magnetic field, associated with the 0.7 structure in conductance. This suppression evolves with increasing field into the shot-noise signature of spin-lifted mode degeneracy. Quantitative agreement is found with a phenomenological model for density-dependent mode splitting. Shot noise measurements of multi-lead quantum-dot structures in the Coulomb blockade regime distill the mechanisms by which Coulomb interaction and quantum indistinguishability correlate electron flow. Gate-controlled sign reversal of noise cross correlation in two capacitively-coupled dots is observed, and shown to

  6. Lightweight, Low-Loss dc Transducer

    NASA Technical Reports Server (NTRS)

    Nagano, S.; Koerner, T.; Brisendine, P.; Weiner, H.; Detwiler, R.

    1982-01-01

    Direct current is measured by lightweight, magnetically coupled transducer that weighs only 4 grams, without actually being wired into circuit under test. Miniature dc transducer has five windings: 2 for ac excitation inputs, 2 for dc control inputs, and 1 for feedback. Wire gages are selected for minimum size and weight. Size and number of turns of dc windings are selected according to dc current range to be measured.

  7. 49 CFR 372.219 - Washington, DC

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 5 2012-10-01 2012-10-01 false Washington, DC 372.219 Section 372.219... ZONES, AND TERMINAL AREAS Commercial Zones § 372.219 Washington, DC The zone adjacent to, and... points within a line drawn 15 miles beyond the municipal limits of Washington, DC (c) All points...

  8. 49 CFR 372.219 - Washington, DC

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 5 2010-10-01 2010-10-01 false Washington, DC 372.219 Section 372.219... ZONES, AND TERMINAL AREAS Commercial Zones § 372.219 Washington, DC The zone adjacent to, and... points within a line drawn 15 miles beyond the municipal limits of Washington, DC (c) All points...

  9. 49 CFR 372.219 - Washington, DC

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 5 2014-10-01 2014-10-01 false Washington, DC 372.219 Section 372.219... ZONES, AND TERMINAL AREAS Commercial Zones § 372.219 Washington, DC The zone adjacent to, and... points within a line drawn 15 miles beyond the municipal limits of Washington, DC (c) All points...

  10. 49 CFR 372.219 - Washington, DC

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 5 2011-10-01 2011-10-01 false Washington, DC 372.219 Section 372.219... ZONES, AND TERMINAL AREAS Commercial Zones § 372.219 Washington, DC The zone adjacent to, and... points within a line drawn 15 miles beyond the municipal limits of Washington, DC (c) All points...

  11. Washington: A DC Circuit Tour

    NASA Astrophysics Data System (ADS)

    Halpern, Paul

    2010-12-01

    I explore the history of physics in Washington, D.C., and its environs through a tour of notable sites and personalities. Highlights include visits to the Smithsonian and Carnegie Institutions, stops at the Einstein Memorial, George Washington University, the University of Maryland, and the American Center for Physics, and biographical sketches of physicists Joseph Henry, George Gamow, Edward Teller, and others who worked in the District of Columbia.

  12. Transformerless dc-Isolated Converter

    NASA Technical Reports Server (NTRS)

    Rippel, Wally E.

    1987-01-01

    Efficient voltage converter employs capacitive instead of transformer coupling to provide dc isolation. Offers buck/boost operation, minimal filtering, and low parts count, with possible application in photovoltaic power inverters, power supplies and battery charges. In photovoltaic inverter circuit with transformerless converter, Q2, Q3, Q4, and Q5 form line-commutated inverter. Switching losses and stresses nil because switching performed when current is zero.

  13. Advanced DC/DC Converters towards higher Volumetric Efficiencies for Space Applications

    NASA Technical Reports Server (NTRS)

    Plante, Jeannette; Shue, Jack; Liu, David; Wang, Bright; Shaw, Harry

    2005-01-01

    Contents include the following: 1. NASA mission outlook. 2. Issues with DC/DC converter for space. 3. Statement of newly initiated engineering activities for DC/DC converter. 4. Overview of prototyping work with novel materials. 5. Results of cryogenic testing.

  14. 76 FR 68745 - DC Energy, LLC; DC Energy Mid-Atlantic, LLC

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-11-07

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF ENERGY Federal Energy Regulatory Commission DC Energy, LLC; DC Energy Mid-Atlantic, LLC v. PJM Interconnection, L.L.C... Federal Energy Regulatory Commission (Commission), 18 CFR 385.206 (2011), DC Energy, LLC (DC Energy)...

  15. Power Network impedance effects on noise emission of DC-DC converters

    NASA Astrophysics Data System (ADS)

    Esteban, M. C.; Arteche, F.; Iglesias, M.; Gimeno, A.; Arcega, F. J.; Johnson, M.; Cooper, W. E.

    2012-01-01

    The characterization of electromagnetic noise emissions of DC-DC converters is a critical issue that has been analyzed during the desing phase of CMS tracker upgrade. Previous simulation studies showed important variations in the level of conducted emissions when DC-DC converters are loaded/driven by different impedances and power network topologies. Several tests have been performed on real DC-DC converters to validate the Pspice model and simulation results. This paper presents these test results. Conducted noise emissions at the input and at the output terminals of DC-DC converters has been measured for different types of power and FEE impedances. Special attention has been paid to influence on the common-mode emissions by the carbon fiber material used to build the mechanical structure of the central detector. These study results show important recommendations and criteria to be applied in order to decrease the system noise level when integrating the DC-DC.

  16. Technique for sensing inductor and dc output currents of PWM dc-dc converter

    SciTech Connect

    Ma, K.; Lee, Y. . Dept. of Electronic Engineering)

    1994-05-01

    The design, analysis and trade-offs of a novel method to sense the inductor and dc output currents of PWM converters are presented. By sensing and adding appropriately the currents in the transistor, rectifier and capacitors of a converter using current transformers, the waveforms of inductor and dc output currents can be reconstructed accurately while maintaining isolation. This method offers high bandwidth, clean waveform, practically zero power dissipation and simple circuit. The technique is applicable to all PWM converters in both continuous and discontinuous modes, and is most suitable for the implementation of current mode control schemes like hysteretic, PWM conductance control, and output current feedforward. This approach has been experimentally verified at a wide range of current levels, duty cycles, and switching frequencies up to 1.4 MHz.

  17. Arcing on dc power systems

    NASA Technical Reports Server (NTRS)

    Moores, Greg; Heller, R. P.; Sutanto, Surja; Dugal-Whitehead, Norma R.

    1992-01-01

    Unexpected and undesirable arcing on dc power systems can produce hazardous situations aboard space flights. The potential for fire and shock might exist in a situation where there is a broken conductor, a loose power connection, or a break in the insulation of the power cable. Such arcing has been found to be reproducible in a laboratory environment. Arcing tests show that the phenomena can last for several seconds and yet be undetectable by present protection schemes used in classical power relaying and remote power controller applications. This paper characterizes the arcing phenomena and suggests future research that is needed.

  18. Block clustering based on difference of convex functions (DC) programming and DC algorithms.

    PubMed

    Le, Hoai Minh; Le Thi, Hoai An; Dinh, Tao Pham; Huynh, Van Ngai

    2013-10-01

    We investigate difference of convex functions (DC) programming and the DC algorithm (DCA) to solve the block clustering problem in the continuous framework, which traditionally requires solving a hard combinatorial optimization problem. DC reformulation techniques and exact penalty in DC programming are developed to build an appropriate equivalent DC program of the block clustering problem. They lead to an elegant and explicit DCA scheme for the resulting DC program. Computational experiments show the robustness and efficiency of the proposed algorithm and its superiority over standard algorithms such as two-mode K-means, two-mode fuzzy clustering, and block classification EM.

  19. Simultaneous distribution of AC and DC power

    DOEpatents

    Polese, Luigi Gentile

    2015-09-15

    A system and method for the transport and distribution of both AC (alternating current) power and DC (direct current) power over wiring infrastructure normally used for distributing AC power only, for example, residential and/or commercial buildings' electrical wires is disclosed and taught. The system and method permits the combining of AC and DC power sources and the simultaneous distribution of the resulting power over the same wiring. At the utilization site a complementary device permits the separation of the DC power from the AC power and their reconstruction, for use in conventional AC-only and DC-only devices.

  20. Development of a DC-DC conversion powering scheme for the CMS Phase-1 pixel upgrade

    NASA Astrophysics Data System (ADS)

    Feld, L.; Fimmers, C.; Karpinski, W.; Klein, K.; Lipinski, M.; Preuten, M.; Rauch, M.; Rittich, D.; Sammet, J.; Wlochal, M.

    2014-01-01

    A novel powering scheme based on the DC-DC conversion technique will be exploited to power the CMS Phase-1 pixel detector. DC-DC buck converters for the CMS pixel project have been developed, based on the AMIS5 ASIC designed by CERN. The powering system of the Phase-1 pixel detector is described and the performance of the converter prototypes is detailed, including power efficiency, stability of the output voltage, shielding, and thermal management. Results from a test of the magnetic field tolerance of the DC-DC converters are reported. System tests with pixel modules using many components of the future pixel barrel system are summarized. Finally first impressions from a pre-series of 200 DC-DC converters are presented.

  1. Hybrid-Circuit Module For Dc-To-Dc Power Converter

    NASA Technical Reports Server (NTRS)

    Vorperian, Vatche; Detwiler, Robert; Karmon, Dan

    1996-01-01

    Power hybrid module is general-purpose power-switching module providing flexibility in design and application. Complete dc-to-dc power converter constructed by adding input/output filters and feedback circuitry to module to suit specific application.

  2. DC-10 winglet flight evaluation

    NASA Technical Reports Server (NTRS)

    1983-01-01

    The results of a flight evaluation of winglets on a DC-10 Series 10 aircraft are presented. For sensitive areas of comparison, effects of winglets were determined back to back with and without winglets. Basic and reduced span winglet configurations were tested. After initial encounter with low speed buffet, a number of acceptable configurations were developed. For maximum drag reduction at both cruise and low speeds, lower winglets were required, having leading edge devices on upper and lower winglets for the latter regime. The cruise benefits were enhanced by adding outboard aileron droop to the reduced span winglet aircraft. Winglets had no significant impact on stall speeds, high speed buffet boundary, and stability and control characteristics. Flutter test results agreed with predictions and ground vibration data. Flight loads measurement also agreed with predictions.

  3. High voltage DC power supply

    DOEpatents

    Droege, T.F.

    1989-12-19

    A high voltage DC power supply having a first series resistor at the output for limiting current in the event of a short-circuited output, a second series resistor for sensing the magnitude of output current, and a voltage divider circuit for providing a source of feedback voltage for use in voltage regulation is disclosed. The voltage divider circuit is coupled to the second series resistor so as to compensate the feedback voltage for a voltage drop across the first series resistor. The power supply also includes a pulse-width modulated control circuit, having dual clock signals, which is responsive to both the feedback voltage and a command voltage, and also includes voltage and current measuring circuits responsive to the feedback voltage and the voltage developed across the second series resistor respectively. 7 figs.

  4. High voltage DC power supply

    DOEpatents

    Droege, Thomas F.

    1989-01-01

    A high voltage DC power supply having a first series resistor at the output for limiting current in the event of a short-circuited output, a second series resistor for sensing the magnitude of output current, and a voltage divider circuit for providing a source of feedback voltage for use in voltage regulation is disclosed. The voltage divider circuit is coupled to the second series resistor so as to compensate the feedback voltage for a voltage drop across the first series resistor. The power supply also includes a pulse-width modulated control circuit, having dual clock signals, which is responsive to both the feedback voltage and a command voltage, and also includes voltage and current measuring circuits responsive to the feedback voltage and the voltage developed across the second series resistor respectively.

  5. Dual wound dc brush motor gearhead

    NASA Technical Reports Server (NTRS)

    Henson, Barrie W.

    1986-01-01

    The design requirements, the design, development tests and problems, the qualification and life test and the findings of the strip examination of a dual wound DC brushed motor gearhead are described. It is the only space qualified dual wound dc brushed motor gearhead in Europe.

  6. DC KIDS COUNT e-Databook Indicators

    ERIC Educational Resources Information Center

    DC Action for Children, 2012

    2012-01-01

    This report presents indicators that are included in DC Action for Children's 2012 KIDS COUNT e-databook, their definitions and sources and the rationale for their selection. The indicators for DC KIDS COUNT represent a mix of traditional KIDS COUNT indicators of child well-being, such as the number of children living in poverty, and indicators of…

  7. DC3 Data and Information Page

    Atmospheric Science Data Center

    2015-03-16

    Deep Convective Clouds and Chemistry (DC3) Data and Information The Deep Convective Clouds and Chemistry ( DC3 ) field campaign is investigating the impact of deep, ... processes, on upper tropospheric (UT) composition and chemistry. The primary science objectives are:   To quantify and ...

  8. DC-based magnetic field controller

    DOEpatents

    Kotter, D.K.; Rankin, R.A.; Morgan, J.P.

    1994-05-31

    A magnetic field controller is described for laboratory devices and in particular to dc operated magnetic field controllers for mass spectrometers, comprising a dc power supply in combination with improvements to a Hall probe subsystem, display subsystem, preamplifier, field control subsystem, and an output stage. 1 fig.

  9. DC-based magnetic field controller

    DOEpatents

    Kotter, Dale K.; Rankin, Richard A.; Morgan, John P,.

    1994-01-01

    A magnetic field controller for laboratory devices and in particular to dc operated magnetic field controllers for mass spectrometers, comprising a dc power supply in combination with improvements to a hall probe subsystem, display subsystem, preamplifier, field control subsystem, and an output stage.

  10. ALA 2010: Where to Eat in DC

    ERIC Educational Resources Information Center

    Library Journal, 2010

    2010-01-01

    As host to visitors and transplants from around the world, Washington, DC, benefits from the constant infusion of different cultures. Although most neighborhoods lack a unified culinary flavor, make no mistake: DC is a city of distinctive areas, each with its own style, ensuring that hungry American Library Association (ALA) 2010 conference…

  11. Close-Range Gunfire around DC Schools

    ERIC Educational Resources Information Center

    Bieler, Sam; La Vigne, Nancy

    2014-01-01

    This report examines the incidence of gunfire as measured by gunshot detection technology using data from the 2011-2012 school year. It finds that a disproportionate volume of gunfire happened near a small share of DC schools. About half of DC schools covered by gunshot detection sensors are in close proximity to gunfire, and four schools were…

  12. Modeling of DC spacecraft power systems

    NASA Technical Reports Server (NTRS)

    Berry, F. C.

    1995-01-01

    Future spacecraft power systems must be capable of supplying power to various loads. This delivery of power may necessitate the use of high-voltage, high-power dc distribution systems to transmit power from the source to the loads. Using state-of-the-art power conditioning electronics such as dc-dc converters, complex series and parallel configurations may be required at the interface between the source and the distribution system and between the loads and the distribution system. This research will use state-variables to model and simulate a dc spacecraft power system. Each component of the dc power system will be treated as a multiport network, and a state model will be written with the port voltages as the inputs. The state model of a component will be solved independently from the other components using its state transition matrix. A state-space averaging method is developed first in general for any dc-dc switching converter, and then demonstrated in detail for the particular case of the boost power stage. General equations for both steady-state (dc) and dynamic effects (ac) are obtained, from which important transfer functions are derived and applied to a special case of the boost power stage.

  13. The dc power circuits: A compilation

    NASA Technical Reports Server (NTRS)

    1972-01-01

    A compilation of reports concerning power circuits is presented for the dissemination of aerospace information to the general public as part of the NASA Technology Utilization Program. The descriptions for the electronic circuits are grouped as follows: dc power supplies, power converters, current-voltage power supply regulators, overload protection circuits, and dc constant current power supplies.

  14. Modeling of DC spacecraft power systems

    NASA Astrophysics Data System (ADS)

    Berry, F. C.

    1995-07-01

    Future spacecraft power systems must be capable of supplying power to various loads. This delivery of power may necessitate the use of high-voltage, high-power dc distribution systems to transmit power from the source to the loads. Using state-of-the-art power conditioning electronics such as dc-dc converters, complex series and parallel configurations may be required at the interface between the source and the distribution system and between the loads and the distribution system. This research will use state-variables to model and simulate a dc spacecraft power system. Each component of the dc power system will be treated as a multiport network, and a state model will be written with the port voltages as the inputs. The state model of a component will be solved independently from the other components using its state transition matrix. A state-space averaging method is developed first in general for any dc-dc switching converter, and then demonstrated in detail for the particular case of the boost power stage. General equations for both steady-state (dc) and dynamic effects (ac) are obtained, from which important transfer functions are derived and applied to a special case of the boost power stage.

  15. A high voltage ratio and low ripple interleaved DC-DC converter for fuel cell applications.

    PubMed

    Chang, Long-Yi; Chao, Kuei-Hsiang; Chang, Tsang-Chih

    2012-01-01

    This paper proposes a high voltage ratio and low ripple interleaved boost DC-DC converter, which can be used to reduce the output voltage ripple. This converter transfers the low DC voltage of fuel cell to high DC voltage in DC link. The structure of the converter is parallel with two voltage-doubler boost converters by interleaving their output voltages to reduce the voltage ripple ratio. Besides, it can lower the current stress for the switches and inductors in the system. First, the PSIM software was used to establish a proton exchange membrane fuel cell and a converter circuit model. The simulated and measured results of the fuel cell output characteristic curve are made to verify the correctness of the established simulation model. In addition, some experimental results are made to validate the effectiveness in improving output voltage ripple of the proposed high voltage ratio interleaved boost DC-DC converters.

  16. A high voltage ratio and low ripple interleaved DC-DC converter for fuel cell applications.

    PubMed

    Chang, Long-Yi; Chao, Kuei-Hsiang; Chang, Tsang-Chih

    2012-01-01

    This paper proposes a high voltage ratio and low ripple interleaved boost DC-DC converter, which can be used to reduce the output voltage ripple. This converter transfers the low DC voltage of fuel cell to high DC voltage in DC link. The structure of the converter is parallel with two voltage-doubler boost converters by interleaving their output voltages to reduce the voltage ripple ratio. Besides, it can lower the current stress for the switches and inductors in the system. First, the PSIM software was used to establish a proton exchange membrane fuel cell and a converter circuit model. The simulated and measured results of the fuel cell output characteristic curve are made to verify the correctness of the established simulation model. In addition, some experimental results are made to validate the effectiveness in improving output voltage ripple of the proposed high voltage ratio interleaved boost DC-DC converters. PMID:23365536

  17. A High Voltage Ratio and Low Ripple Interleaved DC-DC Converter for Fuel Cell Applications

    PubMed Central

    Chang, Long-Yi; Chao, Kuei-Hsiang; Chang, Tsang-Chih

    2012-01-01

    This paper proposes a high voltage ratio and low ripple interleaved boost DC-DC converter, which can be used to reduce the output voltage ripple. This converter transfers the low DC voltage of fuel cell to high DC voltage in DC link. The structure of the converter is parallel with two voltage-doubler boost converters by interleaving their output voltages to reduce the voltage ripple ratio. Besides, it can lower the current stress for the switches and inductors in the system. First, the PSIM software was used to establish a proton exchange membrane fuel cell and a converter circuit model. The simulated and measured results of the fuel cell output characteristic curve are made to verify the correctness of the established simulation model. In addition, some experimental results are made to validate the effectiveness in improving output voltage ripple of the proposed high voltage ratio interleaved boost DC-DC converters. PMID:23365536

  18. DC/DC Power Converter for Super-Capacitor Supplied by Electric Power Splitter

    NASA Astrophysics Data System (ADS)

    Haubert, T.; Mindl, P.

    The aim of the article is design of DC/DC converter and discussing of problematic supply using electric power splitter. The electric power splitter with AC/DC converter is source for the DC/DC converter, which is dedicated for charging and discharging of hybrid car drive super-capacitor energy storage. The electric power splitter is synchronous machine with two rotating parts. First rotor contains permanent magnet and the second rotor contains three-phase windings. The amplitude of output voltage depends on difference between first and second rotor speed. The main role of the DC/DC converter is to optimize energy content in super-capacitor storage used to acceleration and deceleration driving period of the passenger car with hybrid electric vehicle (HEV) drive system using electric power splitter.

  19. Lessons learned: DC-X

    NASA Technical Reports Server (NTRS)

    Steinmeyer, D. A.

    1996-01-01

    The DC-X was conceived and developed specifically to lay the ground work for significantly lowering the cost of space operations. The system design was based on an initial set of program goals and a finite, limited set of resources. The goal in its simplest terms was to demonstrate vertical landing after rotation of the vehicle from a nose-first to an engines-first altitude. Finite resources actually drove the selection of a robust design to reduce fabrication and preflight testing costs. The result was a system with a large amount of flexibility which allowed expansion of the test goals as the system, and test program, evolved. The use of the vehicle flight computer interfacing with the ground control system for flight crew training was also not an initial concept. However, by defining an architecture for the system control modes which allowed additions and modifications as learning progressed, the 6 DOF codes used for flight controls software development were transported to the operating system to be used in a simulated flight mode. Flight data reduction was also greatly improved as the program progressed, and the data needs and presentation were refined. The software, avionics hardware, and the FOCC system development proceeded ahead of the vehicle, primarily because most of the hardware elements were existing at the outset of the program. The Built-in-Test (BIT) for avionics and propulsion systems were adequate. Particularly the flight readiness system which verified the vehicle health after engine start and before throttle-up for flight.

  20. DC-10 winglet flight evaluation

    NASA Technical Reports Server (NTRS)

    Taylor, A. B.

    1983-01-01

    Results of a flight evaluation of winglets on a DC-10 Series 10 aircraft are presented. For sensitive areas of comparison, effects of winglets were determined back-to-back with and without winglets. Basic and reduced-span winglet configurations were tested. After initial encounter with low-speed buffet, a number of acceptable configurations were developed. For maximum drag reduction at both cruise and low speeds, lower winglets were required, having leading edge devices on upper and lower winglets for the latter regime. The cruise benefits were enhanced by adding outboard aileron droop to the reduced-span winglet aircraft. Winglets had no significant impact on stall speeds, high-speed buffet boundary, and stability and control. Flutter test results agreed with predictions and ground vibration data. Flight loads measurement, provided in a concurrent program, also agreed with predictions. It was estimated that a production version of the aircraft, using the reduced-span winglet and aileron droop, would yield a 3-percent reduction in fuel burned with capacity payload. This range was 2% greater than with winglets. A 5% reduction in takeoff distance at maximum takeoff weight would also result.

  1. High sensitivity ancilla assisted nanoscale DC magnetometry

    NASA Astrophysics Data System (ADS)

    Liu, Yixiang; Ajoy, Ashok; Marseglia, Luca; Saha, Kasturi; Cappellaro, Paola

    2016-05-01

    Sensing slowly varying magnetic fields are particularly relevant to many real world scenarios, where the signals of interest are DC or close to static. Nitrogen Vacancy (NV) centers in diamond are a versatile platform for such DC magnetometry on nanometer length scales. Using NV centers, the standard technique for measuring DC magnetic fields is via the Ramsey protocol, where sensitivities can approach better than 1 μ T/vHz, but are limited by the sensor fast dephasing time T2*. In this work we instead present a method of sensing DC magnetic fields that is intrinsically limited by the much longer T2 coherence time. The method exploits a strongly-coupled ancillary nuclear spin to achieve high DC field sensitivities potentially exceeding that of the Ramsey method. In addition, through this method we sense the perpendicular component of the DC magnetic field, which in conjunction with the parallel component sensed by the Ramsey method provides a valuable tool for vector DC magnetometry at the nanoscale.

  2. DC-Compensated Current Transformer †

    PubMed Central

    Ripka, Pavel; Draxler, Karel; Styblíková, Renata

    2016-01-01

    Instrument current transformers (CTs) measure AC currents. The DC component in the measured current can saturate the transformer and cause gross error. We use fluxgate detection and digital feedback compensation of the DC flux to suppress the overall error to 0.15%. This concept can be used not only for high-end CTs with a nanocrystalline core, but it also works for low-cost CTs with FeSi cores. The method described here allows simultaneous measurements of the DC current component. PMID:26805830

  3. DC isolation and protection system and circuit

    NASA Technical Reports Server (NTRS)

    Wagner, Charles A. (Inventor); Kellogg, Gary V. (Inventor)

    1991-01-01

    A precision analog electronic circuit that is capable of sending accurate signals to an external device that has hostile electric characteristics, including the presence of very large common mode voltages. The circuit is also capable of surviving applications of normal mode overvoltages of up to 120 VAC/VDC for unlimited periods of time without damage or degradation. First, the circuit isolates the DC signal output from the computer. Means are then provided for amplifying the isolated DC signal. Further means are provided for stabilizing and protecting the isolating and amplifying means, and the isolated and amplified DC signal which is output to the external device, against overvoltages and overcurrents.

  4. High power density dc/dc converter: Selection of converter topology

    NASA Technical Reports Server (NTRS)

    Divan, Deepakraj M.

    1990-01-01

    The work involved in the identification and selection of a suitable converter topology is described. Three new dc/dc converter topologies are proposed: Phase-Shifted Single Active Bridge DC/DC Converter; Single Phase Dual Active Bridges DC/DC Converter; and Three Phase Dual Active Bridges DC/DC Converter (Topology C). The salient features of these topologies are: (1) All are minimal in structure, i.e., each consists of an input and output bridge, input and output filter and a transformer, all components essential for a high power dc/dc conversion process; (2) All devices of both the bridges can operate under near zero-voltage conditions, making possible a reduction of device switching losses and hence, an increase in switching frequency; (3) All circuits operate at a constant frequency, thus simplifying the task of the magnetic and filter elements; (4) Since, the leakage inductance of the transformer is used as the main current transfer element, problems associated with the diode reverse recovery are eliminated. Also, this mode of operation allows easy paralleling of multiple modules for extending the power capacity of the system; (5) All circuits are least sensitive to parasitic impedances, infact the parasitics are efficently utilized; and (6) The soft switching transitions, result in low electromagnetic interference. A detailed analysis of each topology was carried out. Based on the analysis, the various device and component ratings for each topology operating at an optimum point, and under the given specifications, are tabulated and discussed.

  5. Robust DC/DC converter control for polymer electrolyte membrane fuel cell application

    NASA Astrophysics Data System (ADS)

    Wang, Ya-Xiong; Yu, Duck-Hyun; Chen, Shi-An; Kim, Young-Bae

    2014-09-01

    This study investigates a robust controller in regulating the pulse width modulation (PWM) of a DC/DC converter for a polymer electrolyte membrane fuel cell (PEMFC) application. A significant variation in the output voltage of a PEMFC depends on the power requirement and prevents a PEMFC from directly connecting to a subsequent power bus. DC/DC converters are utilized to step-up or step-down voltage to match the subsequent power bus voltage. In this study, a full dynamic model, which includes a PEMFC and boost and buck DC/DC converters, is developed under MATLAB/Simulink environment for control. A robust PWM duty ratio control for the converters is designed using time delay control (TDC). This control enables state variables to accurately follow the dynamics of a reference model using time-delayed information of plant input and output information within a few sampling periods. To prove the superiority of the TDC performance, traditional proportional-integral control (PIC) and model predictive control (MPC) are designed and implemented, and the simulation results are compared. The efficacies of TDC for the PEMFC-fed PWM DC/DC converters are validated through experimental test results using a 100 W PEMFC as well as boost and buck DC/DC converters.

  6. Novel bidirectional DC-DC converters based on the three-state switching cell

    NASA Astrophysics Data System (ADS)

    da Silva Júnior, José Carlos; Robles Balestero, Juan Paulo; Lessa Tofoli, Fernando

    2016-05-01

    It is well known that there is an increasing demand for bidirectional DC-DC converters for applications that range from renewable energy sources to electric vehicles. Within this context, this work proposes novel DC-DC converter topologies that use the three-state switching cell (3SSC), whose well-known advantages over conventional existing structures are ability to operate at high current levels, while current sharing is maintained by a high frequency transformer; reduction of cost and dimensions of magnetics; improved distribution of losses, with consequent increase of global efficiency and reduction of cost associated to the need of semiconductors with lower current ratings. Three distinct topologies can be derived from the 3SSC: one DC-DC converter with reversible current characteristic able to operate in the first and second quadrants; one DC-DC converter with reversible voltage characteristic able to operate in the first and third quadrants and one DC-DC converter with reversible current and voltage characteristics able to operate in four quadrants. Only the topology with bidirectional current characteristic is analysed in detail in terms of the operating stages in both nonoverlapping and overlapping modes, while the design procedure of the power stage elements is obtained. In order to validate the theoretical assumptions, an experimental prototype is also implemented, so that relevant issues can be properly discussed.

  7. Development of a fuzzy logic controller for dc/dc converters: Design, computer simulation, and experimental evaluation

    SciTech Connect

    So, W.C.; Tse, C.K.; Lee, Y.S.

    1996-01-01

    The design of a fuzzy logic controller for dc/dc converters is described in this paper. A brief review of fuzzy logic and its application to control is first given. Then, the derivation of a fuzzy control algorithm for regulating dc/dc converters is described in detail. The proposed fuzzy control is evaluated by computer simulations as well as experimental measurements of the closed-loop performance of simple dc/dc converters in respect of load regulation and line regulation.

  8. DC-8 Takeoff in Kiruna, Sweden

    NASA Video Gallery

    NASA is using a DC-8 aircraft as a flying science laboratory. The platform aircraft, based at NASA's Dryden Flight Research Center, Edwards, Calif., collects data for many experiments in support of...

  9. Variable load automatically tests dc power supplies

    NASA Technical Reports Server (NTRS)

    Burke, H. C., Jr.; Sullivan, R. M.

    1965-01-01

    Continuously variable load automatically tests dc power supplies over an extended current range. External meters monitor current and voltage, and multipliers at the outputs facilitate plotting the power curve of the unit.

  10. dc power system for deuteron accelerator

    SciTech Connect

    Creek, K.O.; Liska, D.J.

    1981-01-01

    The Fusion Materials Irradiation Test (FMIT) Facility dc power system provides excitation current for all linac and High-Energy Beam Transport (HEBT) quadrupole and bending magnets, excitation for horizontal and vertical beam steering, and current-bypass shunts.

  11. Advanced DC/DC Converters Towards Higher Volumetric Efficiencies For Space Applications

    NASA Technical Reports Server (NTRS)

    Shaw, Harry; Shue, Jack; Liu, David; Wang, Bright; Plante, Jeanette

    2005-01-01

    A new emphasis on planetary exploration by NASA drives the need for small, high power DC/DC converters which are functionally modular. NASA GSFC and other government space organizations are supporting technology development in the DC/DC converter area to both meet new needs and to promote more sources of supply. New technologies which enable miniaturization such as embedded passive technologies and thermal management using high thermal conductivity materials are features of the new designs. Construction of some simple DC/DC converter core circuits using embedded components was found to be successful for increasing volumetric efficiency to 37 W/inch. The embedded passives were also able to perform satisfactorily in this application in cryogenic temperatures.

  12. Test Results of Selected Commercial DC/DC Converters under Cryogenic Temperatures - A Digest

    NASA Technical Reports Server (NTRS)

    Patterson, Richard; Hammoud, Ahmad

    2010-01-01

    DC/DC converters are widely used in space power systems in the areas of power management and distribution, signal conditioning, and motor control. Design of DC/DC converters to survive cryogenic temperatures will improve the power system performance, simplify design, and reduce development and launch costs. In this work, the performance of nine COTS modular, low-tomedium power DC/DC converters was investigated under cryogenic temperatures. The converters were evaluated in terms of their output regulation, efficiency, and input and output currents. At a given temperature, these properties were obtained at various input voltages and at different load levels. A summary on the performance of the tested converters was given. More comprehensive testing and in-depth analysis of performance under long-term exposure to extreme temperatures are deemed necessary to establish the suitability of these and other devices for use in the harsh environment of space exploration missions.

  13. The DC-DC conversion power system of the CMS Phase-1 pixel upgrade

    NASA Astrophysics Data System (ADS)

    Feld, L.; Karpinski, W.; Klein, K.; Lipinski, M.; Preuten, M.; Rauch, M.; Schmitz, St.; Wlochal, M.

    2015-01-01

    The pixel detector of the CMS experiment will be exchanged during the year-end technical stop in 2016/2017, as part of the experiment's Phase-1 upgrade. The new device will feature approximately twice the number of readout channels, and consequently the power consumption will be doubled. By moving to a DC-DC conversion powering scheme, it is possible to power the new pixel detector with the existing power supplies and cable plant. The power system of the Phase-1 pixel detector is described and the performance of the new components, including DC-DC converters, DC-DC converter motherboards and various power distribution boards, is detailed. The outcome of system tests in terms of electrical behaviour, thermal management and pixel module performance is discussed.

  14. Current Fed Step-up DC/DC Converter for Fuel Cell Inverter Applications

    NASA Astrophysics Data System (ADS)

    Andreičiks, Aleksandrs; Vitols, Kristaps; Krievs, Oskars; Steiks, Ingars

    2009-01-01

    In order to use hydrogen fuel cells in domestic applications either as main power supply or backup source, their low DC output voltage has to be matched to the level and frequency of the utility grid AC voltage. Such power converter systems usually consist of a DC-DC converter and a DC-AC inverter. Comparison of different current fed step-up DC/DC converters is done in this paper and a double inductor step-up push-pull converter investigated, presenting simulation and experimental results. The converter is elaborated for 1200 W power to match the rated power of the proton exchange membrane (PEM) fuel cell located in hydrogen fuel cell research laboratory of Riga Technical University.

  15. DC-DC converters with reduced mass for trackers at the HL-LHC

    NASA Astrophysics Data System (ADS)

    Affolder, A.; Allongue, B.; Blanchot, G.; Faccio, F.; Fuentes, C.; Greenall, A.; Michelis, S.

    2011-11-01

    The development at CERN of low noise DC-DC converters for the powering of front-end systems enables the implementation of efficient powering schemes for the physics experiments at the HL-LHC. Recent tests made on the ATLAS short strip tracker modules confirm the full electromagnetic compatibility of the DC-DC converter prototypes with front-end detectors. The integration of the converters in the trackers front-ends needs to address also the material budget constraints. The impact of the DC-DC converters onto the material budget of the ATLAS tracker modules is discussed and mass reduction techniques are explored, leading to a compromise between electromagnetic compatibility and mass. Low mass shield implementations and Aluminum core inductors are proposed. Also, the impact on emitted noise due to a size reduction of critical components is discussed. Finally, material reduction techniques are discussed at the board layout and manufacturing levels.

  16. Nonlinear Phenomena and Resonant Parametric Perturbation Control in QR-ZCS Buck DC-DC Converters

    NASA Astrophysics Data System (ADS)

    Hsieh, Fei-Hu; Liu, Feng-Shao; Hsieh, Hui-Chang

    The purpose of this study is to investigate the chaotic phenomena and to control in current-mode controlled quasi-resonant zero-current-switching (QR-ZCS) DC-DC buck converters, and to present control of chaos by resonant parametric perturbation control methods. First of all, MATLAB/SIMULINK is used to derive a mathematical model for QR-ZCS DC-DC buck converters, and to simulate the converters to observe the waveform of output voltages, inductance currents and phase-plane portraits from the period-doubling bifurcation to chaos by changing the load resistances. Secondly, using resonant parametric perturbation control in QR-ZCS buck DC-DC converters, the simulation results of the chaotic converter form chaos state turn into stable state period 1, and improve ripple amplitudes of converters under the chaos, to verify the validity of the proposes method.

  17. Critical conditions of saddle-node bifurcations in switching DC-DC converters

    NASA Astrophysics Data System (ADS)

    Fang, Chung-Chieh

    2013-08-01

    Although existence of multiple periodic orbits in some DC-DC converters have been known for decades, linking the multiple periodic orbits with the saddle-node bifurcation (SNB) is rarely reported. The SNB occurs in popular DC-DC converters, but it is generally reported as a strange instability. Recently, design-oriented instability critical conditions are of great interest. In this article, average, sampled-data and harmonic balance analyses are applied and they lead to equivalent results. Many new critical conditions are derived. They facilitate future research on the instability associated with multiple periodic orbits, sudden voltage jumps or disappearances of periodic orbits observed in DC-DC converters. The effects of various converter parameters on the instability can be readily seen from the derived critical conditions. New Nyquist-like plots are also proposed to predict or prevent the occurrence of the instability.

  18. Application handbook for a Standardized Control Module (SCM) for DC-DC converters, volume 1

    NASA Technical Reports Server (NTRS)

    Lee, F. C.; Mahmoud, M. F.; Yu, Y.

    1980-01-01

    The standardized control module (SCM) was developed for application in the buck, boost and buck/boost DC-DC converters. The SCM used multiple feedback loops to provide improved input line and output load regulation, stable feedback control system, good dynamic transient response and adaptive compensation of the control loop for changes in open loop gain and output filter time constraints. The necessary modeling and analysis tools to aid the design engineer in the application of the SCM to DC-DC Converters were developed. The SCM functional block diagram and the different analysis techniques were examined. The average time domain analysis technique was chosen as the basic analytical tool. The power stage transfer functions were developed for the buck, boost and buck/boost converters. The analog signal and digital signal processor transfer functions were developed for the three DC-DC Converter types using the constant on time, constant off time and constant frequency control laws.

  19. Modelling and Simulation of Digital Compensation Technique for dc-dc Converter by Pole Placement

    NASA Astrophysics Data System (ADS)

    Shenbagalakshmi, R.; Sree Renga Raja, T.

    2015-09-01

    A thorough and effective analysis of the dc-dc converters is carried out in order to achieve the system stability and to improve the dynamic performance. A small signal modelling based on state space averaging technique for dc-dc converters is carried out. A digital state feedback gain matrix is derived by pole placement technique in order to achieve the stability of a completely controllable system. A prediction observer for the dc-dc converters is designed and a dynamic compensation (observer plus control law) is provided using separation principle. The output is very much improved with zero output voltage ripples, zero peak overshoot, and much lesser settling time in the range of ms and with higher overall efficiency (>90 %).

  20. High power density dc/dc converter: Component selection and design

    NASA Technical Reports Server (NTRS)

    Divan, Deepakraj M.

    1989-01-01

    Further work pertaining to design considerations for the new high power, high frequency dc/dc converters is discussed. The goal of the project is the development of high power, high power density dc/dc converters at power levels in the multi-kilowatt to megawatt range for aerospace applications. The prototype converter is rated for 50 kW at a switching frequency of 50 kHz, with an input voltage of 200 Vdc and an output of 2000 Vdc. The overall power density must be in the vicinity of 0.2 to 0.3 kg/kW.

  1. The application of standardized control and interface circuits to three dc to dc power converters.

    NASA Technical Reports Server (NTRS)

    Yu, Y.; Biess, J. J.; Schoenfeld, A. D.; Lalli, V. R.

    1973-01-01

    Standardized control and interface circuits were applied to the three most commonly used dc to dc converters: the buck-boost converter, the series-switching buck regulator, and the pulse-modulated parallel inverter. The two-loop ASDTIC regulation control concept was implemented by using a common analog control signal processor and a novel digital control signal processor. This resulted in control circuit standardization and superior static and dynamic performance of the three dc-to-dc converters. Power components stress control, through active peak current limiting and recovery of switching losses, was applied to enhance reliability and converter efficiency.

  2. Analysis of a class of pulse modulated dc-to-dc power converters

    NASA Technical Reports Server (NTRS)

    Burger, P.

    1975-01-01

    The basic operational characteristics of dc-to-dc converters are analyzed. The basic physical characteristics of power converters are identified. A simple class of dc-to-dc power converters is chosen which could satisfy any set of operating requirements. Three different controlling methods in this class are described in detail. Necessary conditions for the stability of these converters are measured through analog computer simulation. These curves are related to other operational characteristics, such as ripple and regulation. Finally, further research is suggested for the solution of the physical design of absolutely stable, reliable, and efficient power converters of this class.

  3. Model predictive control of bidirectional isolated DC-DC converter for energy conversion system

    NASA Astrophysics Data System (ADS)

    Akter, Parvez; Uddin, Muslem; Mekhilef, Saad; Tan, Nadia Mei Lin; Akagi, Hirofumi

    2015-08-01

    Model predictive control (MPC) is a powerful and emerging control algorithm in the field of power converters and energy conversion systems. This paper proposes a model predictive algorithm to control the power flow between the high-voltage and low-voltage DC buses of a bidirectional isolated full-bridge DC-DC converter. The predictive control algorithm utilises the discrete nature of the power converters and predicts the future nature of the system, which are compared with the references to calculate the cost function. The switching state that minimises the cost function is selected for firing the converter in the next sampling time period. The proposed MPC bidirectional DC-DC converter is simulated with MATLAB/Simulink and further verified with a 2.5 kW experimental configuration. Both the simulation and experimental results confirm that the proposed MPC algorithm of the DC-DC converter reduces reactive power by avoiding the phase shift between primary and secondary sides of the high-frequency transformer and allow power transfer with unity power factor. Finally, an efficiency comparison is performed between the MPC and dual-phase-shift-based pulse-width modulation controlled DC-DC converter which ensures the effectiveness of the MPC controller.

  4. Analysis of high voltage step-up nonisolated DC-DC boost converters

    NASA Astrophysics Data System (ADS)

    Alisson Alencar Freitas, Antônio; Lessa Tofoli, Fernando; Junior, Edilson Mineiro Sá; Daher, Sergio; Antunes, Fernando Luiz Marcelo

    2016-05-01

    A high voltage step-up nonisolated DC-DC converter based on coupled inductors suitable to photovoltaic (PV) systems applications is proposed in this paper. Considering that numerous approaches exist to extend the voltage conversion ratio of DC-DC converters that do not use transformers, a detailed comparison is also presented among the proposed converter and other popular topologies such as the conventional boost converter and the quadratic boost converter. The qualitative analysis of the coupled-inductor-based topology is developed so that a design procedure can be obtained, from which an experimental prototype is implemented to validate the theoretical assumptions.

  5. A Reduced-Part, Triple-Voltage DC-DC Converter for Electric Vehicle Power Management

    SciTech Connect

    Su, Gui-Jia; Tang, Lixin

    2007-01-01

    Electrical power systems in future hybrid and fuel cell vehicles may consist of three voltage nets; 14 V, 42 V and high voltage (>200 V) buses. A soft-switched, bi-directional dc-dc converter using only four switches was proposed for interconnecting the three nets. This paper presents a reduced- part dc-dc converter, which decreases the converter cost while retaining all the favorable features of the original topology. Simulation and experimental data are included to verify a simple power flow control scheme.

  6. Efficiency and Regulation of Commercial Low Power DC/DC Converter Modules at Low Temperatures

    NASA Technical Reports Server (NTRS)

    Elbuluk, Malik E.; Gerber, Scott; Hammoud, Ahmad; Patterson, Richard L.

    2000-01-01

    DC/DC converters that are capable of operating at cryogenic temperatures are anticipated to play an important role in the power systems of future NASA deep space missions. Design of these converters to survive cryogenic temperatures will improve the power system performance, and reduce development and launch costs. At the NASA Glenn Research Center Low Temperature Electronics Laboratory, several commercial off-the-shelf dc/dc converter modules were evaluated for their low temperature performance. Various parameters were investigated as a function of temperature, in the range of 20 C to -190 C. Data pertaining to the efficiency and voltage regulation of the tested converters is presented and discussed.

  7. Interleaved DC-DC Converter with Discrete Duty Cycle and Open Loop Control

    NASA Astrophysics Data System (ADS)

    Kroics, K.; Sokolovs, A.

    2016-08-01

    The authors present the control principle of the multiphase interleaved DC-DC converter that can be used to vastly reduce output current ripple of the converter. The control algorithm can be easily implemented by using microcontroller without current loop in each phase. The converter works in discontinuous conduction mode (DCM) but close to boundary conduction mode (BCM). The DC-DC converter with such a control algorithm is useful in applications that do not require precise current adjustment. The prototype of the converter has been built. The experimental results of the current ripple are presented in the paper.

  8. Improved DC Gun Insulator Assembly

    SciTech Connect

    Sah, R.; Dudas, A.; Neubauer, M. L.; Poelker, M.; Surles-Law, K. E.L.

    2010-05-23

    Many user fa­cil­i­ties such as syn­chrotron ra­di­a­tion light sources and free elec­tron lasers re­quire ac­cel­er­at­ing struc­tures that sup­port elec­tric fields of 10-100 MV/m, es­pe­cial­ly at the start of the ac­cel­er­a­tor chain where ce­ram­ic in­su­la­tors are used for very high gra­di­ent DC guns. These in­su­la­tors are dif­fi­cult to man­u­fac­ture, re­quire long com­mis­sion­ing times, and often ex­hib­it poor re­li­a­bil­i­ty. Two tech­ni­cal ap­proach­es to solv­ing this prob­lem will be in­ves­ti­gat­ed. First­ly, in­vert­ed ce­ram­ics offer so­lu­tions for re­duced gra­di­ents be­tween the elec­trodes and ground. An in­vert­ed de­sign will be pre­sent­ed for 350 kV, with max­i­mum gra­di­ents in the range of 5-10 MV/m. Sec­ond­ly, novel ce­ram­ic man­u­fac­tur­ing pro­cess­es will be stud­ied, in order to pro­tect triple junc­tion lo­ca­tions from emis­sion, by ap­ply­ing a coat­ing with a bulk re­sis­tiv­i­ty. The pro­cess­es for cre­at­ing this coat­ing will be op­ti­mized to pro­vide pro­tec­tion as well as be used to coat a ce­ram­ic with an ap­pro­pri­ate gra­di­ent in bulk re­sis­tiv­i­ty from the vac­u­um side to the air side of an HV stand­off ce­ram­ic cylin­der. Ex­am­ple in­su­la­tor de­signs are being com­put­er mod­elled, and in­su­la­tor sam­ples are being man­u­fac­tured and test­ed

  9. 14 CFR 93.339 - Requirements for operating in the DC SFRA, including the DC FRZ.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... aircraft is equipped with an operating automatic altitude reporting transponder; (4) Before operating an aircraft in the DC SFRA, including the DC FRZ, the pilot obtains and transmits a discrete transponder code from Air Traffic Control, and the aircraft's transponder continues to transmit the assigned code...

  10. Regulation of a lightweight high efficiency capacitator diode voltage multiplier dc-dc converter

    NASA Technical Reports Server (NTRS)

    Harrigill, W. T., Jr.; Myers, I. T.

    1976-01-01

    A method for the regulation of a capacitor diode voltage multiplier dc-dc converter has been developed which has only minor penalties in weight and efficiency. An auxiliary inductor is used, which only handles a fraction of the total power, to control the output voltage through a pulse width modulation method in a buck boost circuit.

  11. Computer-aided analysis and simulation of switched dc-dc converters

    NASA Technical Reports Server (NTRS)

    Lee, F. C.; Yu, Y.

    1978-01-01

    State space techniques are employed to derive an equivalent nonlinear recurrent time-domain model that describes the switched dc-dc converter behavior exactly. This model is employed effectively to analyze both large signal behavior by propagating the recurrence equation and matching boundary conditions through digital computation and small signal behavior by linearizing it about the equilibrium state.

  12. Regulation of a lightweight high efficiency capacitor diode voltage multiplier dc-dc converter

    NASA Technical Reports Server (NTRS)

    Harrigill, W. T., Jr.; Myers, I. T.

    1976-01-01

    A method for the regulation of a capacitor diode voltage multiplier dc-dc converter has been developed which has only minor penalties in weight and efficiency. An auxiliary inductor is used, which only handles a fraction of the total power, to control the output voltage through a pulse width modulation method in a buck boost circuit.

  13. A DC-DC conversion powering scheme for the CMS Phase-1 pixel upgrade

    NASA Astrophysics Data System (ADS)

    Feld, L.; Fleck, M.; Friedrichs, M.; Hensch, R.; Karpinski, W.; Klein, K.; Sammet, J.; Wlochal, M.

    2013-02-01

    The CMS pixel detector was designed for a nominal instantaneous LHC luminosity of 1ṡ1034 cm-2s-1. During Phase-1 of the LHC upgrade, the instantaneous luminosity will be increased to about twice this value. To preserve the excellent performance of the pixel detector despite the increase in particle rates and track densities, the CMS Collaboration foresees the exchange of its pixel detector in the shutdown 2016/2017. The new pixel detector will be improved in many respects, and will comprise twice the number of readout channels. A powering scheme based on DC-DC conversion will be adopted, which will enable the provision of the required power with the present cable plant. The powering scheme of the CMS pixel detector will be described, and the performance of prototype DC-DC buck converters will be presented, including power efficiency, system tests with DC-DC converters and pixel modules, thermal management, reliability at low temperature, and studies of potential frequency locking between DC-DC converters.

  14. Modelling, simulation and construction of a dc/dc boost power converter: a school experimental system

    NASA Astrophysics Data System (ADS)

    Silva-Ortigoza, R.; Silva-Ortigoza, G.; Hernández-Guzmán, V. M.; Saldaña-González, G.; Marcelino-Aranda, M.; Marciano-Melchor, M.

    2012-05-01

    We introduce a dc/dc boost power converter as a didactic prototype intended to support courses on electric circuit analysis experimentally. The corresponding mathematical model is obtained, the converter is designed and an experimental setup is described, constructed and tested. Simplicity of construction as well as low cost of components renders the feasible introduction of this equipment in undergraduate laboratories.

  15. Single Event Burnout in DC-DC Converters for the LHC Experiments

    SciTech Connect

    Claudio H. Rivetta et al.

    2001-09-24

    High voltage transistors in DC-DC converters are prone to catastrophic Single Event Burnout in the LHC radiation environment. This paper presents a systematic methodology to analyze single event effects sensitivity in converters and proposes solutions based on de-rating input voltage and output current or voltage.

  16. Modelling, Simulation and Construction of a DC/DC Boost Power Converter: A School Experimental System

    ERIC Educational Resources Information Center

    Silva-Ortigoza, R.; Silva-Ortigoza, G.; Hernandez-Guzman, V. M.; Saldana-Gonzalez, G.; Marcelino-Aranda, M.; Marciano-Melchor, M.

    2012-01-01

    We introduce a dc/dc boost power converter as a didactic prototype intended to support courses on electric circuit analysis experimentally. The corresponding mathematical model is obtained, the converter is designed and an experimental setup is described, constructed and tested. Simplicity of construction as well as low cost of components renders…

  17. Homopolar dc motor and trapped flux brushless dc motor using high temperature superconductor materials

    SciTech Connect

    Crapo, A.D.; Lloyd, J.D. )

    1991-03-01

    This paper reports on two motors designed and built for use with high temperature superconductor (HTSC) materials. They are a homopolar DC motor that will use HTSC field windings and a brushless DC motor that will use bulk HTSC material to trap flux in steel rotor poles. The HTSC field windings of the homopolar DC motor are designed to operate at 1000 Amperes/cm{sup 2} in a 0.010 Tesla (100 Gauss) field. In order to maximize torque in the homopolar DC motor, an iron magnetic circuit with small air gaps gives maximum flux for minimum Ampere turns in the field. A copper field winding version of the homopolar DC motor has been tested while the authors wait for 575 Ampere turn HTSC coils.

  18. Type I IFN regulate DC turnover in vivo.

    PubMed

    Mattei, Fabrizio; Bracci, Laura; Tough, David F; Belardelli, Filippo; Schiavoni, Giovanna

    2009-07-01

    DC are the most potent antigen-presenting cells that recognise signs of infection and serve as the main activators of naïve T cells. We have previously shown that type I IFN (IFN-I) are produced by DC and can act in an autocrine manner to activate DC. In the present study, we have investigated the role of IFN-I in regulating the turnover and lifespan of DC. We found that DC, especially the CD8alpha(+) subset, from type I IFN receptor knock out (IFNAR KO) mice, display a reduced turnover rate when compared with DC from WT mice, as revealed by BrdU labelling kinetics. In vitro, IFNAR KO BM precursor cells cultured in the presence of GM-CSF generated CD11c(+) DC less efficiently than WT BM, and the IFNAR KO DC that arose displayed reduced migratory ability. Interestingly, splenic DC from IFNAR KO mice exhibited a higher survival rate in short-term culture compared with control DC. Exposure to IFN-I in vivo markedly increased the turnover rate of splenic DC, particularly CD8alpha(+) DC, which was preceded by a transient induction of apoptosis. In accordance with this, IFN-I stimulated the apoptosis of splenic DC in vitro. Overall, our data indicate that IFN-I are important regulators of DC turnover in vivo and suggest that these cytokines may exert this function through the modulation of multiple processes involving DC apoptosis, proliferation and migration. PMID:19544312

  19. New Experimental Data in DC745U

    SciTech Connect

    Ortiz-Acosta, Denisse; Cady, Carl; Densmore, Crystal

    2012-06-18

    The objectives of this project are: (1) study the molecular and mechanical properties of DC745U - (a) DC745U is a silicone elastomer used in several weapons systems, (b) depending on their chemistry and formulation, polymers can be susceptible to damage and failures due to weak chemical linkages and physical interactions, (c) inefficient production processes can generate heterogeneities throughout the material that can contribute negatively to the overall performance and lifetime of the polyer, (d) aging, long-term thermal and radioactive conditions, and mechanical strains can affect the materials network structure and contribute to the degradation of the production; (2) characterization of DC745U materials cured under different conditions to determine possible differences to the polymer structure; and (3) this work is relevant to mission-critical programs and for supporting programmatic work for weapon research.

  20. Comparison of solar panel cooling system by using dc brushless fan and dc water

    NASA Astrophysics Data System (ADS)

    Irwan, Y. M.; Leow, W. Z.; Irwanto, M.; M, Fareq; Hassan, S. I. S.; Safwati, I.; Amelia, A. R.

    2015-06-01

    The purpose of this article is to discuss comparison of solar panel cooling system by using DC brushless fan and DC water pump. Solar photovoltaic (PV) power generation is an interesting technique to reduce non-renewable energy consumption and as a renewable energy. The temperature of PV modules increases when it absorbs solar radiation, causing a decrease in efficiency. A solar cooling system is design, construct and experimentally researched within this work. To make an effort to cool the PV module, Direct Current (DC) brushless fan and DC water pump with inlet/outlet manifold are designed for constant air movement and water flow circulation at the back side and front side of PV module representatively. Temperature sensors were installed on the PV module to detect temperature of PV. PIC microcontroller was used to control the DC brushless fan and water pump for switch ON or OFF depend on the temperature of PV module automatically. The performance with and without cooling system are shown in this experiment. The PV module with DC water pump cooling system increase 3.52%, 36.27%, 38.98%in term of output voltage, output current, output power respectively. It decrease 6.36 °C compare than to PV module without DC water pump cooling system. While DC brushless fan cooling system increase 3.47%, 29.55%, 32.23%in term of output voltage, output current, and output power respectively. It decrease 6.1 °C compare than to PV module without DC brushless fan cooling system. The efficiency of PV module with cooling system was increasing compared to PV module without cooling system; this is because the ambient temperature dropped significantly. The higher efficiency of PV cell, the payback period of the system can be shorted and the lifespan of PV module can also be longer.

  1. Regulated high efficiency, lightweight capacitor-diode multiplier dc to dc converter

    NASA Technical Reports Server (NTRS)

    Harrigill, W. T., Jr.; Myers, I. T. (Inventor)

    1978-01-01

    A voltage multiplier having a capacitor-diode voltage multiplying network is disclosed which is fed with voltage pulses from a dc source through a first switching means. Pulses of a second polarity are also supplied through a second switching means to the input of the capacitor-diode voltage multiplier from a second dc source whose voltage is adjustable to change the voltage of the pulses of second polarity. The switching means are alternately rendered conducting by signals from a control circuit. The second dc source may be controlled by a voltage comparator which compares the output voltage of the capacitor-diode voltage multiplier to the reference source.

  2. DC birdscape: a program for monitoring neotropical migrant birds in Washington, DC

    USGS Publications Warehouse

    Sauer, J.R.; Hadidian, J.; Swarth, C.; Droege, S.; Handly, P.; Diddan, G.; Huff, J.; Bonney, Rick; Pashley, David N.; Cooper, Robert; Niles, Larry

    2000-01-01

    Urban and suburban habitats often contain a variety of Neotropical migratory birds, but are poorly sampled by programs such as the North American Breeding Bird Survey. DC Birdscape was developed to inventory and monitor birds in Washington, D.C. Birds were surveyed using a systematic sample of point counts during 1993-1995. Results indicate that species richness of Neotropical migratory birds varied among land-use categories, and that maximum species richness occurred in parkland habitats. Although DC Birdscape has provided relevant information on bird distribution and species richness, it is unclear whether the information is of sufficient management interest to support its continuation as a long-term monitoring program.

  3. High speed variable-inductor controlled with DC-DC converter

    SciTech Connect

    Ichinokura, Osamu; Kagami, Toshiro; Jinzenji, Toshimasa; Maeda, Mitsuru; Wakiya, Yoshie

    1995-11-01

    This paper describes a fundamental consideration on high speed control of the orthogonal-core type variable-inductor. The variable-inductor is applicable to a VAR compensation in the electric power system. The transient characteristics of the variable-inductor under the condition of dc control are discussed based on simulation and experiment. For high speed operation, the authors present an instantaneous control of the primary current. A simple control circuit using a dc-dc converter is demonstrated in this paper.

  4. New Logic Circuit with DC Parametric Excitation

    NASA Astrophysics Data System (ADS)

    Sugahara, Masanori; Kaneda, Hisayoshi

    1982-12-01

    It is shown that dc parametric excitation is possible in a circuit named JUDO, which is composed of two resistively-connected Josephson junctions. Simulation study proves that the circuit has large gain and properties suitable for the construction of small, high-speed logic circuits.

  5. Manufacturing development of DC-10 advanced rudder

    NASA Technical Reports Server (NTRS)

    Cominsky, A.

    1979-01-01

    The design, manufacture, and ground test activities during development of production methods for an advanced composite rudder for the DC-10 transport aircraft are described. The advanced composite aft rudder is satisfactory for airline service and a cost saving in a full production manufacturing mode is anticipated.

  6. Electrical Anomalies Observed During DC3

    NASA Technical Reports Server (NTRS)

    Lang, Timothy J.; Rutledge, Steven A.; Dolan, Brenda; Krehbiel, Paul; Rison, William; Lindsey, Daniel T.; Lyons, Walt

    2013-01-01

    The primary scientific goals of DC3 involved improving our understanding of the chemical impacts of thunderstorms and their anvils. However, the Colorado domain provided opportunities to study other interesting phenomena, including the potential impacts of smoke ingestion on convection and thunderstorms, electrification processes in smoke plumes and pyrocumulonimbus clouds, and the production of sprites by unconventional thunderstorm.

  7. Halbach array DC motor/generator

    DOEpatents

    Merritt, B.T.; Dreifuerst, G.R.; Post, R.F.

    1998-01-06

    A new configuration of DC motor/generator is based on a Halbach array of permanent magnets. This motor does not use ferrous materials so that the only losses are winding losses and losses due to bearings and windage. An ``inside-out`` design is used as compared to a conventional motor/generator design. The rotating portion, i.e., the rotor, is on the outside of the machine. The stationary portion, i.e., the stator, is formed by the inside of the machine. The rotor contains an array of permanent magnets that provide a uniform field. The windings of the motor are placed in or on the stator. The stator windings are then ``switched`` or ``commutated`` to provide a DC motor/generator much the same as in a conventional DC motor. The commutation can be performed by mechanical means using brushes or by electronic means using switching circuits. The invention is useful in electric vehicles and adjustable speed DC drives. 17 figs.

  8. Halbach array DC motor/generator

    DOEpatents

    Merritt, Bernard T.; Dreifuerst, Gary R.; Post, Richard F.

    1998-01-01

    A new configuration of DC motor/generator is based on a Halbach array of permanent magnets. This motor does not use ferrous materials so that the only losses are winding losses and losses due to bearings and windage. An "inside-out" design is used as compared to a conventional motor/generator design. The rotating portion, i.e., the rotor, is on the outside of the machine. The stationary portion, i.e., the stator, is formed by the inside of the machine. The rotor contains an array of permanent magnets that provide a uniform field. The windings of the motor are placed in or on the stator. The stator windings are then "switched" or "commutated" to provide a DC motor/generator much the same as in a conventional DC motor. The commutation can be performed by mechanical means using brushes or by electronic means using switching circuits. The invention is useful in electric vehicles and adjustable speed DC drives.

  9. Computerized Torque Control for Large dc Motors

    NASA Technical Reports Server (NTRS)

    Willett, Richard M.; Carroll, Michael J.; Geiger, Ronald V.

    1987-01-01

    Speed and torque ranges in generator mode extended. System of shunt resistors, electronic switches, and pulse-width modulation controls torque exerted by large, three-phase, electronically commutated dc motor. Particularly useful for motor operating in generator mode because it extends operating range to low torque and high speed.

  10. DC-DC power converter research for Orbiter/Station power exchange

    NASA Technical Reports Server (NTRS)

    Ehsani, M.

    1993-01-01

    This project was to produce innovative DC-DC power converter concepts which are appropriate for the power exchange between the Orbiter and the Space Station Freedom (SSF). The new converters must interface three regulated power buses on SSF, which are at different voltages, with three fuel cell power buses on the Orbiter which can be at different voltages and should be tracked independently. Power exchange is to be bi-directional between the SSF and the Orbiter. The new converters must satisfy the above operational requirements with better weight, volume, efficiency, and reliability than is available from the present conventional technology. Two families of zero current DC-DC converters were developed and successfully adapted to this application. Most of the converters developed are new and are presented.

  11. Cryogenic Evaluation of an Advanced DC/DC Converter Module for Deep Space Applications

    NASA Technical Reports Server (NTRS)

    Elbuluk, Malik E.; Hammoud, Ahmad; Gerber, Scott S.; Patterson, Richard

    2003-01-01

    DC/DC converters are widely used in power management, conditioning, and control of space power systems. Deep space applications require electronics that withstand cryogenic temperature and meet a stringent radiation tolerance. In this work, the performance of an advanced, radiation-hardened (rad-hard) commercial DC/DC converter module was investigated at cryogenic temperatures. The converter was investigated in terms of its steady state and dynamic operations. The output voltage regulation, efficiency, terminal current ripple characteristics, and output voltage response to load changes were determined in the temperature range of 20 to -140 C. These parameters were obtained at various load levels and at different input voltages. The experimental procedures along with the results obtained on the investigated converter are presented and discussed.

  12. A Ring-Type SC DC-DC Converter with Series-Connected Capacitors

    NASA Astrophysics Data System (ADS)

    Eguchi, Kei; Tabata, Toru; Zhu, Hongbing; Ueno, Fumio; Inoue, Takahiro

    A ring-type SC DC-DC converter with series-connected capacitors is proposed in this paper. The series-connected capacitors in a ring-connection enable us to convert an input voltage at short step-up/step-down interval. Hence, the proposed circuit can provide more various types of output-voltages than conventional converters. Concerning the proposed DC-DC converter, SPICE simulations are performed to investigate the characteristics of the circuit. The SPICE simulations show that 1. the proposed circuit can realize shorter step-up/step-down interval than the conventional ring-type power converter and 2. the efficiency is more than 95 % when the output load Ro = 1kΩ.

  13. A Nonlinear Digital Control Solution for a DC/DC Power Converter

    NASA Technical Reports Server (NTRS)

    Zhu, Minshao

    2002-01-01

    A digital Nonlinear Proportional-Integral-Derivative (NPID) control algorithm was proposed to control a 1-kW, PWM, DC/DC, switching power converter. The NPID methodology is introduced and a practical hardware control solution is obtained. The design of the controller was completed using Matlab (trademark) Simulink, while the hardware-in-the-loop testing was performed using both the dSPACE (trademark) rapid prototyping system, and a stand-alone Texas Instruments (trademark) Digital Signal Processor (DSP)-based system. The final Nonlinear digital control algorithm was implemented and tested using the ED408043-1 Westinghouse DC-DC switching power converter. The NPID test results are discussed and compared to the results of a standard Proportional-Integral (PI) controller.

  14. Novel Full-bridge ZVS DC-DC Converter with an Clamp Diodes

    NASA Astrophysics Data System (ADS)

    Guangqun, Nan; Xue, Hu

    The two arms of this converter all work at zero-voltage switching condition, that bring many advantages, such as little loss of power, simple control, etc. But these also exists some problems, such as parasitic oscillation on the output rectifier diodes. A novel full-bridge ZVS PWM DC-DC converter which adopts two clamping diodes in the first side of the transformer is proposed to reduce the parasitic oscillation in this paper. In this paper, It heavily analyzes the realization process of their soft-switching and the reason of related issues and solution, we establishes simulation model and simulates using orCAD. Finally,a 5 kW ZVS PWM DC-DC converter Prototype in that TMS320F2812 is the core controlled chip has been set up, and the experiments showed us the validation of the correlative theory.

  15. Chaos, bifurcation and intermittent phenomena in DC-DC converters under resonant parametric perturbation

    NASA Astrophysics Data System (ADS)

    Deivasundari, P.; Geetha, R.; Uma, G.; Murali, K.

    2013-07-01

    DC-DC converters act as a black box to study various bifurcations. In the present study, the influence of external periodic interference signal in the input of DC-DC voltage-mode controlled buck converter has been considered. It is found that the presence of sinusoidal or saw-tooth interference signal whose frequency is comparable with the switching frequency of the converter or its rational multiples manifests as remerging chaotic band attractors (or Feigenbaum trees) and intermittent chaos. However, the presence of sinusoidal interference signal having irrational frequency ratios with the switching frequency of the converter leads to quasi-periodic route to chaos. The study was carried out both theoretically and experimentally.

  16. Integrated ZVS DC-DC converter with continuous input current and high voltage gain

    NASA Astrophysics Data System (ADS)

    Do, Hyun-Lark

    2011-09-01

    An integrated zero-voltage-switching (ZVS) DC-DC converter with continuous input current and high voltage gain is proposed. The proposed converter can operate with soft switching, a continuous inductor current and fixed switching frequency. The voltage stress of the power switches is relatively low compared to the output voltage. Moreover, soft-switching characteristic of the proposed converter reduces switching loss of active power switches and raise the conversion efficiency. The reverse-recovery problem of output rectifiers is also alleviated by controlling the current changing rates of diodes with the use of the leakage inductance of a coupled inductor. The operation and performance of the proposed DC-DC converter were verified on an 115 W experimental prototype operating at 100 kHz.

  17. SUBCONTRACT REPORT: DC-DC Converter for Fuel Cell and Hybrid Vehicles

    SciTech Connect

    Marlino, Laura D; Zhu, Lizhi

    2007-07-01

    The goal of this project is to develop and fabricate a 5kW dc-dc converter with a baseline 14V output capability for fuel cell and hybrid vehicles. The major objectives for this dc-dc converter technology are to meet: Higher efficiency (92%); High coolant temperature,e capability (105 C); High reliability (15 Years/150,000miles); Smaller volume (5L); Lower weight (6kg); and Lower cost ($75/kW). The key technical challenge for these converters is the 105 C coolant temperatures. The power switches and magnetics must be designed to sustain these operating temperatures reliably, without a large cost/mass/volume penalty.

  18. Sliding-mode control of single input multiple output DC-DC converter

    NASA Astrophysics Data System (ADS)

    Zhang, Libo; Sun, Yihan; Luo, Tiejian; Wan, Qiyang

    2016-10-01

    Various voltage levels are required in the vehicle mounted power system. A conventional solution is to utilize an independent multiple output DC-DC converter whose cost is high and control scheme is complicated. In this paper, we design a novel SIMO DC-DC converter with sliding mode controller. The proposed converter can boost the voltage of a low-voltage input power source to a controllable high-voltage DC bus and middle-voltage output terminals, which endow the converter with characteristics of simple structure, low cost, and convenient control. In addition, the sliding mode control (SMC) technique applied in our converter can enhance the performances of a certain SIMO DC-DC converter topology. The high-voltage DC bus can be regarded as the main power source to the high-voltage facility of the vehicle mounted power system, and the middle-voltage output terminals can supply power to the low-voltage equipment on an automobile. In the respect of control algorithm, it is the first time to propose the SMC-PID (Proportion Integration Differentiation) control algorithm, in which the SMC algorithm is utilized and the PID control is attended to the conventional SMC algorithm. The PID control increases the dynamic ability of the SMC algorithm by establishing the corresponding SMC surface and introducing the attached integral of voltage error, which endow the sliding-control system with excellent dynamic performance. At last, we established the MATLAB/SIMULINK simulation model, tested performance of the system, and built the hardware prototype based on Digital Signal Processor (DSP). Results show that the sliding mode control is able to track a required trajectory, which has robustness against the uncertainties and disturbances.

  19. A Three-Phase Bidirectional DC-DC Converter for Automotive Applications

    SciTech Connect

    Su, Gui-Jia; Tang, Lixin

    2008-01-01

    This paper presents a three-phase soft-switching, bidirectional dc-dc converter for high-power automotive applications. The converter employs dual three-phase active bridges and operates with a novel asymmetrical but fixed duty cycle for the top and bottom switches of each phase leg. Simulation and experimental data on a 6-kW prototype are included to verify the novel operating and power flow control principles.

  20. High performance dc-dc conversion with voltage multipliers. [using transformerless capacitor diode circuit

    NASA Technical Reports Server (NTRS)

    Harrigill, W. T., Jr.; Myers, I. T.

    1974-01-01

    An experimental 100W 1000V dc-dc converter using a capacitor diode voltage multipler (CDVM) with a nominal frequency of 100 kHz is studied. A component weight of about 1 kg/kW was obtained. Design equations for current, output -ripple and -power, efficiency and output voltage are derived. Agreement between experimental results and calculations is fairly good except for ripple.

  1. A Versatile Step-Up/Step-Down Switched-Capacitor-Based DC-DC Converter

    NASA Astrophysics Data System (ADS)

    Wei, Chia-Ling; Wu, Lu-Yao; Yang, Hsiu-Hui; Tsai, Chien-Hung; Liu, Bin-Da; Chang, Soon-Jyh

    For battery-powered electronic products, one way to extend battery life is to use a versatile step-up/step-down DC-DC converter. A new versatile step-up/step-down switched-capacitor-based converter structure is proposed, and its efficiency is analyzed. In the step-down case, the efficiency is the same as, or even better than the efficiency of linear regulators.

  2. Linearized stability analysis and design of a flyback dc-dc boost regulator.

    NASA Technical Reports Server (NTRS)

    Wester, G. W.

    1973-01-01

    Analytic expressions for the small-signal power-stage describing functions of a switched dc-dc boost regulator are derived from an approximate continuous circuit model which is developed by a time-averaging technique. Closed-loop stability is attained through the design of frequency compensation of the loop gain. Open- and closed-loop regulator output impedances are derived from the linearized models for the given configuration. The analysis and design are compared with and confirmed by breadboard measurements.

  3. Efficiency and weight of voltage multiplier type ultra lightweight dc-dc converters

    NASA Technical Reports Server (NTRS)

    Harrigill, W. T., Jr.; Myers, I. T.

    1975-01-01

    An analytical and experimental study was made of a capacitor-diode voltage multiplier without a transformer which offers the possibility of high efficiency with light weight. The dc-dc conversion efficiencies of about 94 percent were achieved at output powers of 150 watts at 1000 volts using 8x multiplication. A detailed identification of losses was made, including forward drop losses in component, switching losses, reverse junction capacitance charging losses, and charging losses in the main ladder capacitors.

  4. Materials Testing on the DC-X and DC-XA

    NASA Technical Reports Server (NTRS)

    Smith, Dane; Carroll, Carol; Marschall, Jochen; Pallix, Joan

    1997-01-01

    Flight testing of thermal protection materials has been carried out over a two year period on the base heat shield of the Delta Clipper (DC-X and DC-XA), as well on a body flap. The purpose was to use the vehicle as a test bed for materials and more efficient repair or maintenance processes which would be potentially useful for application on new entry vehicles (i.e., X-33, RLV, planetary probes), as well as on the existing space shuttle orbiters. Panels containing Thermal Protection Systems (TPS) and/or structural materials were constructed either at NASA Ames Research Center or at McDonnell Douglas Aerospace (MDA) and attached between two of the four thrusters in the base heat shield of the DC-X or DC-XA. Three different panels were flown on DC-X flights 6, 7, and 8. A total of 7 panels were flown on DC-XA flights 1, 2, and 3. The panels constructed at Ames contained a variety of ceramic TPS including flexible blankets, tiles with high emissivity coatings, lightweight ceramic ablators and other ceramic composites. The MDS test panels consisted primarily of a variety of metallic composites. This report focuses on the ceramic TPS test results.

  5. Brushless dc motor uses electron beam switching tube as commutator

    NASA Technical Reports Server (NTRS)

    Studer, P.

    1965-01-01

    Electron beam switching tube eliminates physical contact between rotor and stator in brushless dc motor. The tube and associated circuitry control the output of a dc source to sequentially energize the motor stator windings.

  6. Static DC to DC Power Conditioning-Active Ripple Filter, 1 MHZ DC to DC Conversion, and Nonlinear Analysis. Ph.D. Thesis; [voltage regulation and conversion circuitry for spacecraft power supplies

    NASA Technical Reports Server (NTRS)

    Sander, W. A., III

    1973-01-01

    Dc to dc static power conditioning systems on unmanned spacecraft have as their inputs highly fluctuating dc voltages which they condition to regulated dc voltages. These input voltages may be less than or greater than the desired regulated voltages. The design of two circuits which address specific problems in the design of these power conditioning systems and a nonlinear analysis of one of the circuits are discussed. The first circuit design is for a nondissipative active ripple filter which uses an operational amplifier to amplify and cancel the sensed ripple voltage. A dc to dc converter operating at a switching frequency of 1 MHz is the second circuit discussed. A nonlinear analysis of the type of dc to dc converter utilized in designing the 1 MHz converter is included.

  7. Artificial neural network based permanent magnet DC motor drives

    SciTech Connect

    Hoque, M.A. Zaman, M.R.; Rahman, M.A.

    1995-12-31

    A novel scheme for the speed control of a permanent magnet (PM) dc motor drive incorporating artificial neural network (ANN) is proposed. The drive system includes an ANN speed controller, micro-processor based dc-dc converter and a laboratory PM dc motor. A multi-layer artificial neural network structure with a feedback loop is designed in order to precisely operate the control circuit for the dc-dc converter. The complete drive system is simulated and implemented in real time. Both the simulation and experimental results prove the inherent capability of the ANN which makes it possible to maintain desired speed control in the presence of parameter variations and load disturbances. The performances of the ANN based PM dc drive system are compared with the simulated results of the conventionally controlled drive system. This clearly indicates the better performance of the ANN based PM dc motor drive system, particularly in case of parameter and load variations.

  8. DC-DC Type High-Frequency Link DC for Improved Power Quality of Cascaded Multilevel Inverter

    NASA Astrophysics Data System (ADS)

    Sadikin, Muhammad; Senjyu, Tomonobu; Yona, Atsushi

    2013-06-01

    Multilevel inverters are emerging as a new breed of power converter options for power system applications. Recent advances in power switching devices enabled the suitability of multilevel inverters for high voltage and high power applications because they are connecting several devices in series without the need of component matching. Usually, a transformerless battery energy storage system, based on a cascaded multilevel inverter, is used as a measure for voltage and frequency deviations. System can be reduced in size, weight, and cost of energy storage system. High-frequency link circuit topology is advantageous in realizing compact and light-weight power converters for uninterruptible power supply systems, new energy systems using photovoltaic-cells, fuel-cells and so on. This paper presents a DC-DC type high-frequency link DC (HFLDC) cascaded multilevel inverter. Each converter cell is implemented a control strategy for two H-bridge inverters that are controlled with the same multicarrier pulse width modulation (PWM) technique. The proposed cascaded multilevel inverter generates lower voltage total harmonic distortion (THD) in comparison with conventional cascaded multilevel inverter. Digital simulations are carried out using PSCAD/EMTDC to validate the performance of the proposed cascaded multilevel inverter.

  9. An Optically Controllable Transformation-dc Illusion Device.

    PubMed

    Jiang, Wei Xiang; Luo, Chen Yang; Ge, Shuo; Qiu, Cheng-Wei; Cui, Tie Jun

    2015-08-19

    The concept of multifunctional transformation-dc devices is proposed and verified experimentally. The functions of dc metamaterials can be remotely altered by illuminating with visible light. If the light-induced dc illusion effect is activated, the electrostatic behavior of the original object is perceived as multiple equivalent objects with different pre-designed geometries. The experimental verification of the functional device makes it possible to control sophisticated transformation-dc devices with external light illumination. PMID:26177597

  10. Dendritic Cell (DC) Vaccine in Mouse Lung Cancer Minimal Residual Model; Comparison of Monocyte-derived DC vs. Hematopoietic Stem Cell Derived-DC.

    PubMed

    Baek, Soyoung; Lee, Seog Jae; Kim, Myoung Joo; Lee, Hyunah

    2012-12-01

    The anti-tumor effect of monocyte-derived DC (MoDC) vaccine was studied in lung cancer model with feasible but weak Ag-specific immune response and incomplete blocking of tumor growth. To overcome this limitation, the hematopoietic stem cell-derived DC (SDC) was cultured and the anti-tumor effect of MoDC & SDC was compared in mouse lung cancer minimal residual model (MRD). Therapeutic DCs were cultured from either CD34(+) hematopoietic stem cells with GM-CSF, SCF and IL-4 for 14 days (SDC) or monocytes with GM-CSF and IL-4 for 7 days (MoDC). DCs were injected twice by one week interval into the peritoneum of mice that are inoculated with Lewis Lung Carcinoma cells (LLC) one day before the DC injection. Anti-tumor responses and the immune modulation were observed 3 weeks after the final DC injection. CD11c expression, IL-12 and TGF-β secretion were higher in SDC but CCR7 expression, IFN-γ and IL-10 secretion were higher in MoDC. The proportion of CD11c(+)CD8a(+) cells was similar in both DC cultures. Although both DC reduced the tumor burden, histological anti-tumor effect and the frequencies of IFN-γ secreting CD8(+) T cells were higher in SDC treated group than in MoDC. Conclusively, although both MoDC and SDC can induce the anti-tumor immunity, SDC may be better module as anti-tumor vaccine than MoDC in mouse lung cancer. PMID:23396889

  11. The Fiscal Impact of the D.C. Voucher Program

    ERIC Educational Resources Information Center

    Aud, Susan L.; Michos, Leon

    2006-01-01

    In August 2004 the first ever federally funded school voucher program began in Washington, D.C. Eligible students could attend a private school of their choice in the District of Columbia. Each participant received up to $7,500 for school tuition, fees, and transportation. In addition, the D.C. Public School System (DCPS) and D.C. charter school…

  12. DC-8 Airborne Laboratory in flight over Mt. Whitney

    NASA Technical Reports Server (NTRS)

    1998-01-01

    The DC-8 banking over the jagged peak of Mount Whitney on a February 25, 1998 flight. The DC-8 and a pair of ER-2 aircraft are operated by the Airborne Science program at the NASA Dryden Flight Research Center. NASA, other governmental agencies, academia, and scientific and technical organizations employ the DC-8 for a variety of experiments.

  13. Engine bleed air reduction in DC-10

    NASA Technical Reports Server (NTRS)

    Newman, W. H.; Viele, M. R.

    1980-01-01

    An 0.8 percent fuel savings was achieved by a reduction in engine bleed air through the use of cabin air recirculation. The recirculation system was evaluated in revenue service on a DC-10. The cabin remained comfortable with reductions in cabin fresh air (engine bleed air) as much as 50 percent. Flight test verified the predicted fuel saving of 0.8 percent.

  14. DC CHARACTERIZATION OF HIGH GRADIENT MULTILAYER INSULATORS

    SciTech Connect

    Watson, J A; Caporaso, G J; Sampayan, S E; Sanders, D M; Krogh, M L

    2005-05-26

    We have developed a novel insulator concept that involves the use of alternating layers of conductors and insulators with periods less than 1 mm. We have demonstrated that these structures perform 2 to 5 times better than conventional insulators in long pulse, short pulse, and alternating polarity applications. We present new testing results showing exceptional behavior at DC, with gradients in excess of 110kV/cm in vacuum.

  15. NASA's DC-8 With Rain Mapping Radar

    NASA Technical Reports Server (NTRS)

    1999-01-01

    In a joint venture between NASA and Japan's NASDA, scientists have been using satellites, airplanes, and boats to measure rain physics in and under thunderstorms over open water. This Quick Time movie shows NASA's DC-8 jet with the instruments like the airborne rain mapping radar, i.e., the Advanced Microwave Precipitation Radiometer (AMPR) and a lightening imaging sensor. Earth science and weather studies are an important ongoing function of NASA and its affiliates.

  16. Electrostatic quadrupole DC accelerators for BNCT applications

    SciTech Connect

    Kwan, J.W.; Anderson, O.A.; Reginato, L.L.; Vella, M.C.; Yu, S.S.

    1994-04-01

    A dc electrostatic quadrupole (ESQ) accelerator is capable of producing a 2.5 MeV, 100 mA proton beam for the purpose of generating neutrons for Boron Neutron Capture Therapy. The ESQ accelerator is better than the conventional aperture column in high beam current application due to the presence of stronger transverse field for beam focusing and for suppressing secondary electrons. The major challenge in this type of accelerator is in developing the proper power supply system.

  17. DC Electric Fields at the Magnetopause

    NASA Astrophysics Data System (ADS)

    Laakso, H. E.; Escoubet, C. P.; Masson, A.

    2014-12-01

    In order to understand the transfer of energy, momentum and mass through the magnetopause one needs to know several plasma and field parameters including the DC electric field which is known to be challenging to measure in tenuous plasma regions, e.g. in the inner side of the magnetopause where the density drops below 1/cc. However, each of the Cluster spacecraft carries five different experiments that can provide information about DC electric fields, i.e. double probe antenna (EFW) and electron drift meter (EDI) as well as electron and ion spectrometers (PEACE, CIS-HIA, CIS-CODIF). Each technique is very different and has its own strengths and limitations. Therefore it is important to compare all available measurements before making a judgement on DC electric field variation at the magnetopause; note that only very rarely all five measurements are available at the same time. Although the full-resolution observations in the Cluster archive are calibrated, they can still contain various errors. However, when two experiments show the same field, it is quite likely that this is the right field because the different measurements are based on so complimentary techniques and the field varies so much when the spacecraft moves from the magnetosheath through the magnetopause into the magnetosphere, or vice versa. In this presentation we present several cases of the magnetopause crossings and how the different measurements agree and disagree around the magnetopause region.

  18. Development of a smart DC grid model

    NASA Astrophysics Data System (ADS)

    Dalimunthe, Amty Ma'rufah Ardhiyah; Mindara, Jajat Yuda; Panatarani, Camellia; Joni, I. Made

    2016-03-01

    Smart grid and distributed generation should be the solution of the global climate change and the crisis energy of the main source of electrical power generation which is fossil fuel. In order to meet the rising electrical power demand and increasing service quality demands, as well as reduce pollution, the existing power grid infrastructure should be developed into a smart grid and distributed power generation which provide a great opportunity to address issues related to energy efficiency, energy security, power quality and aging infrastructure systems. The conventional of the existing distributed generation system is an AC grid while for a renewable resources requires a DC grid system. This paper explores the model of smart DC grid by introducing a model of smart DC grid with the stable power generation give a minimal and compressed circuitry that can be implemented very cost-effectively with simple components. The PC based application software for controlling was developed to show the condition of the grid and to control the grid become `smart'. The model is then subjected to a severe system perturbation, such as incremental change in loads to test the performance of the system again stability. It is concluded that the system able to detect and controlled the voltage stability which indicating the ability of power system to maintain steady voltage within permissible rangers in normal condition.

  19. Ac-dc converter firing error detection

    SciTech Connect

    Gould, O.L.

    1996-07-15

    Each of the twelve Booster Main Magnet Power Supply modules consist of two three-phase, full-wave rectifier bridges in series to provide a 560 VDC maximum output. The harmonic contents of the twelve-pulse ac-dc converter output are multiples of the 60 Hz ac power input, with a predominant 720 Hz signal greater than 14 dB in magnitude above the closest harmonic components at maximum output. The 720 Hz harmonic is typically greater than 20 dB below the 500 VDC output signal under normal operation. Extracting specific harmonics from the rectifier output signal of a 6, 12, or 24 pulse ac-dc converter allows the detection of SCR firing angle errors or complete misfires. A bandpass filter provides the input signal to a frequency-to-voltage converter. Comparing the output of the frequency-to-voltage converter to a reference voltage level provides an indication of the magnitude of the harmonics in the ac-dc converter output signal.

  20. Performance of 22.4-kW nonlaminated-frame dc series motor with chopper controller. [a dc to dc voltage converter

    NASA Technical Reports Server (NTRS)

    Schwab, J. R.

    1979-01-01

    Performance data obtained through experimental testing of a 22.4 kW traction motor using two types of excitation are presented. Ripple free dc from a motor-generator set for baseline data and pulse width modulated dc as supplied by a battery pack and chopper controller were used for excitation. For the same average values of input voltage and current, the motor power output was independent of the type of excitation. However, at the same speeds, the motor efficiency at low power output (corresponding to low duty cycle of the controller) was 5 to 10 percentage points lower on chopped dc than on ripple free dc. The chopped dc locked-rotor torque was approximately 1 to 3 percent greater than the ripple free dc torque for the same average current.

  1. Estimation of Bidirectional Buck/boost DC/DC Converters with Electric Double-Layer Capacitors for Energy Storage Systems

    NASA Astrophysics Data System (ADS)

    Funabiki, Shigeyuki; Yamamoto, Masayoshi

    Renewable energy such as wind force and solar light has collected the attention as alternative energy sources of fossil fuel. An energy storage system with an electric double-layer capacitor (EDLC), which balances the demand and supply power, is required in order to introduce the electric power generating system that utilizes renewable energy. Currently, the research and development of these energy storage systems are actively carried out. In the energy storage system with an EDLC, the DC/DC converter having the function of the bidirectional power flow and the buck/boost performance is essential as an interface and power control circuit. There are two types of the bidirectional buck/boost DC/DC converters. One type consists of two buck/boost DC/DC converters with one reactor. The other type consists of two sets of two-quadrant DC/DC converters with one reactor. This paper discusses the comparison of these types of DC/DC converters with bidirectional power flow and buck/boost performance. The two types of DC/DC converters are estimated for their application to the energy storage system with the EDLC. As the voltage endurance of the device is lower and the mean current is smaller in the latter type of converter despite of having twice the number of devices compared to the former, the latter type of converter has the advantage of a smaller reactor, i.e., core volume and loss, and lower loss in the converter.

  2. A pulsed DC gas flow hollow cathode

    NASA Astrophysics Data System (ADS)

    Paduraru, Cristian

    A new gas flow hollow cathode discharge source (GFHC) has been developed, characterized, and applied to thin film deposition by sputtering and low-temperature PECVD. Non-reactive and reactive sputtering processes were investigated using copper and aluminum targets, respectively. For the first time, pulsed DC power was applied to a GFHC in order to avoid arcing caused by electrode surface contamination, and to stabilize the discharge in general. The electrical characteristics of the source, the parameters of the remote plasma and its optical emission, were studied and compared to those of a DC powered GFHC. We determined the electrical characteristics of the plasma, including the temporal behavior of the current and voltage under various conditions of pressure and inert gas flow through the cathode. The transition from a glow discharge mode to the hollow cathode mode was studied in an effort to determine the operating range of the GFHC. A capacitive current was discovered at the beginning of the on-time. The properties of the remote plasma were investigated using averaged and time-resolved Langmuir probe and optical emission measurements. The distribution of the remote plasma density resembles the gas flow velocity distribution through the cathode. Plasma processes during off time (decaying plasma) and on-time (plasma reestablishment) were studied and compared to those in pulsed DC magnetron and high power inductively coupled glow discharges. The dependence of the deposition rate, resistivity and thickness distribution of copper films dependence on pulse parameters, power, inert gas flow through the cathode and pressure have been studied. The thin film thickness distribution is governed by the distribution of the gas flow velocity, which can be calculated using laminar flow gas dynamics. In a pulsed DC GFHC system, the inert gas flow through the cathode prevents the penetration of the reactive gas from the chamber into the cathode. A special reactive gas delivery

  3. New topology for DC/DC bidirectional converter for hybrid systems in renewable energy

    NASA Astrophysics Data System (ADS)

    Lopez, Juan Carlos; Ortega, Manuel; Jurado, Francisco

    2015-03-01

    This article presents a new isolated DC/DC bidirectional converter with soft switching, using a transformer with two voltage taps and two full bridges with insulated-gate bipolar transistors (IGBTs), one on each side of the transformer to be integrated in hybrid systems of renewable energy. A large voltage conversion ratio can be achieved using this converter, in buck and booster modes. Also medium and high DC power can be converted with a good efficiency. Analysis and switching techniques have been reported. To verify the principle of operation, a laboratory prototype of 10 kW has been performed. Experimental results are presented, operating in boost mode. The switching algorithm used has been modelled in MATLAB-Simulink to generate C code. This code has been implemented in a DSP F2812, which has been used to build the prototype.

  4. Dendritic Cell (DC)-Specific Targeting Reveals Stat3 as a Negative Regulator of DC Function

    PubMed Central

    Melillo, Jessica A.; Song, Li; Bhagat, Govind; Blazquez, Ana Belen; Plumlee, Courtney R.; Lee, Carolyn; Berin, Cecilia; Reizis, Boris; Schindler, Christian

    2011-01-01

    Dendritic cells (DCs) must achieve a critical balance between activation and tolerance, a process influenced by cytokines and growth factors. IL-10, which transduces signals through Stat3, has emerged as one important negative regulator of DC activation. To directly examine the role Stat3 plays in regulating DC activity, the Stat3 gene was targeted for deletion with a CD11c-cre transgene. Stat3 CKO mice developed cervical lymphadenopathy as well as a mild ileocolitis that persisted throughout life and was associated with impaired weight gain. Consistent with this, Stat3-deficient DCs demonstrated enhanced immune activity, including increased cytokine production, Ag-dependent T-cell activation and resistance to IL-10–mediated suppression. These results reveal a cell-intrinsic negative regulatory role of Stat3 in DCs and link increased DC activation with perturbed immune homeostasis and chronic mucosal inflammation. PMID:20124100

  5. CMOS-Compatible SOI MESFETS for Radiation-Hardened DC-to-DC Converters

    NASA Technical Reports Server (NTRS)

    Thornton, Trevor; Lepkowski, William; Wilk, Seth

    2013-01-01

    A radiation-tolerant transistor switch has been developed that can operate between 196 and +150 C for DC-to-DC power conversion applications. A prototype buck regulator component was demonstrated to be performing well after a total ionizing dose of 300 krad(Si). The prototype buck converters showed good efficiencies at ultra-high switching speeds in the range of 1 to 10 MHz. Such high switching frequency will enable smaller, lighter buck converters to be developed as part of the next project. Switching regulators are widely used in commercial applications including portable consumer electronics.

  6. A High Power Density DC-DC Converter for Distributed PV Architectures

    SciTech Connect

    Agamy, Mohammed S; Chi, Song; Elasser, Ahmed; Harfman-Todorovic, Maja; Jiang, Yan; Mueller, Frank; Tao, Fengfeng

    2012-06-01

    In order to maximize solar energy harvesting capabilities, power converters have to be designed for high efficiency and good MPPT and voltage/current performance. When many converters are used in distributed systems, power density also becomes an important factor as it allows for simpler system integration. In this paper a high power density string dc-dc converter suitable for distributed medium to large scale PV installation is presented. A simple partial power processing topology, implemented with all silicon carbide devices provides high efficiency as well as high power density. A 3.5kW, 100kHz converter is designed and tested to verify the proposed methods.

  7. Finite-time control of DC-DC buck converters via integral terminal sliding modes

    NASA Astrophysics Data System (ADS)

    Chiu, Chian-Song; Shen, Chih-Teng

    2012-05-01

    This article presents novel terminal sliding modes for finite-time output tracking control of DC-DC buck converters. Instead of using traditional singular terminal sliding mode, two integral terminal sliding modes are introduced for robust output voltage tracking of uncertain buck converters. Different from traditional sliding mode control (SMC), the proposed controller assures finite convergence time for the tracking error and integral tracking error. Furthermore, the singular problem in traditional terminal SMC is removed from this article. When considering worse modelling, adaptive integral terminal SMC is derived to guarantee finite-time convergence under more relaxed stability conditions. In addition, several experiments show better start-up performance and robustness.

  8. DC-DC Converter Topology Assessment for Large Scale Distributed Photovoltaic Plant Architectures

    SciTech Connect

    Agamy, Mohammed S; Harfman-Todorovic, Maja; Elasser, Ahmed; Sabate, Juan A; Steigerwald, Robert L; Jiang, Yan; Essakiappan, Somasundaram

    2011-07-01

    Distributed photovoltaic (PV) plant architectures are emerging as a replacement for the classical central inverter based systems. However, power converters of smaller ratings may have a negative impact on system efficiency, reliability and cost. Therefore, it is necessary to design converters with very high efficiency and simpler topologies in order not to offset the benefits gained by using distributed PV systems. In this paper an evaluation of the selection criteria for dc-dc converters for distributed PV systems is performed; this evaluation includes efficiency, simplicity of design, reliability and cost. Based on this evaluation, recommendations can be made as to which class of converters is best fit for this application.

  9. Improved DC Gun and Insulator Assembly

    SciTech Connect

    Neubauer, Michael; Johnson, Rolland P

    2015-01-11

    Many user facilities such as synchrotron radiation light sources and free electron lasers rely on DC high voltage photoguns with internal field gradients as high as 10 to 15 MV/m. These high gradients often lead to field emission which poses serious problems for the photocathode used to generate the electron beam and the ceramic insulators used to bias the photocathode at high voltage. Ceramic insulators are difficult to manufacture, require long commissioning times, and have poor reliability, in part because energetic electrons bury themselves in the ceramic causing a buildup of charge and eventual puncture, and also because large diameter ceramics are difficult to braze reliably. The lifetimes of photo cathodes inside high current DC guns exhibiting field emission are limited to less than a hundred hours. Reducing the surface gradients on the metals reduces the field emission, which serves to maintain the required ultrahigh vacuum condition. A novel gun design with gradients around 5 MV/m and operating at 350 kV, a major improvement over existing designs, was proposed that allows for the in-situ replacement of photo cathodes in axially symmetric designs using inverted ceramics. In this project, the existing JLAB CEBAF asymmetric gun design with an inverted ceramic support was modeled and the beam dynamics characterized. An improved structure was designed that reduces the surface gradients and improves the beam optics. To minimize the surface gradients, a number of electrostatic gun designs were studied to determine the optimum configuration of the critical electrodes within the gun structure. Coating experiments were carried out to create a charge dissipative coating for cylindrical ceramics. The phase II proposal, which was not granted, included the design and fabrication of an axially symmetric DC Gun with an inverted ceramic that would operate with less than 5 MV/m at 350 kV and would be designed with an in-situ replaceable photo-cathode.

  10. Fun D.C. Jobs for Physicists

    SciTech Connect

    Clark Cully

    2009-09-30

    Physicists make valuable contributions in a wide variety of careers, including those in Washington. Many national challenges, including energy, innovation, and security, create a demand for technically-competent individuals across government. Clark will discuss some of the many programs in D.C. designed to attract the best and brightest minds, from grad-students to professors, from short-term assignments to whole new careers. These are great opportunities to use your expertise and enrich your knowledge of the broader scientific enterprise, all while serving society.

  11. Advances in DC photocathode electron guns

    SciTech Connect

    Bruce M. Dunham; P. Heartmann; Reza Kazimi; Hongxiu Liu; B. M. Poelker; J. S. Price; P. M. Rutt; W. J. Schneider; Charles K. Sinclair

    1998-07-01

    At Jefferson Lab, a DC photoemission gun using GaAs and GaAs-like cathodes provides a source of polarized electrons for the main accelerator. The gun is required to produce high average current with long operational lifetimes and high system throughout. Recent work has shown that careful control of the parameters affecting cathode lifetime lead to dramatic improvements in source operation. These conditions include vacuum and the related effect of ion backbombardment, and precise control of all of the electrons emitted from the cathode. In this paper, the authors will review recent results and discuss implications for future photocathode guns.

  12. Stress relaxation in pulsed DC electromigration measurements

    NASA Astrophysics Data System (ADS)

    Ringler, I. J.; Lloyd, J. R.

    2016-09-01

    When a high current density is applied to a conductor, it activates several driving forces for mass transport that can lead to device failure, the most prominent of which is electromigration. However, there are other driving forces operating as well that can counteract or add to the effects of electromigration. A major driving force is a stress gradient that is developed as a response to electromigration in the presence of a blocking boundary condition. When the electrical stress is interrupted by pulsing DC measurements at low frequency, relaxation of the stress is observed through longer lifetime.

  13. Harmonics generated from a DC biased transformer

    SciTech Connect

    Shu Lu; Yilu Liu; Ree, J. De La . The Bradley Dept. of Electrical Engineering)

    1993-04-01

    The paper presents harmonic characteristics of transformer excitation currents under DC bias caused by geomagnetically induced currents (GIC). A newly developed saturation model of a single phase shell form transformer based on 3D finite element analysis is used to calculate the excitation currents. As a consequence, the complete variations of excitation current harmonics with respect to an extended range of GIC bias are revealed. The results of this study are useful in understanding transformers as harmonic sources and the impact on power systems during a solar magnetic disturbance.

  14. [Temperature measurement of DC argon plasma jet].

    PubMed

    Yan, Jian-Hua; Pan, Xin-Chao; Ma, Zeng-Yi; Tu, Xin; Cen, Ke-Fa

    2008-01-01

    The electron temperature of DC arc plasma jet is an important parameter, which determines the characteristics of plasma jet. The measurement of emission spectrum was performed to obtain the spectral intensities of some Ar lines and the method of diagrammatic view of Boltzmann was adopted to calculate the electron temperature. The results indicated that the electron temperature dropped at different speed along with the axes of the plasma jet and rose rapidly when the current was increased, and it also rose when the flowrate of argon was increased.

  15. Classification of electrical discharges in DC Accelerators

    NASA Astrophysics Data System (ADS)

    Banerjee, Srutarshi; Deb, A. K.; Rajan, Rehim N.; Kishore, N. K.

    2016-08-01

    Controlled electrical discharge aids in conditioning of the system while uncontrolled discharges damage its electronic components. DC Accelerator being a high voltage system is no exception. It is useful to classify electrical discharges according to the severity. Experimental prototypes of the accelerator discharges are developed. Photomultiplier Tubes (PMTs) are used to detect the signals from these discharges. Time and Frequency domain characteristics of the detected discharges are used to extract features. Machine Learning approaches like Fuzzy Logic, Neural Network and Least Squares Support Vector Machine (LSSVM) are employed to classify the discharges. This aids in detecting the severity of the discharges.

  16. Thermoelectric-Generator-Based DC-DC Conversion Networks for Automotive Applications

    NASA Astrophysics Data System (ADS)

    Li, Molan; Xu, Shaohui; Chen, Qiang; Zheng, Li-Rong

    2011-05-01

    Maximizing electrical energy generation through waste heat recovery is one of the modern research questions within automotive applications of thermoelectric (TE) technologies. This paper proposes a novel concept of distributed multisection multilevel DC-DC conversion networks based on thermoelectric generators (TEGs) for automotive applications. The concept incorporates a bottom-up design approach to collect, convert, and manage vehicle waste heat efficiently. Several state-of-the-art thermoelectric materials are analyzed for the purpose of power generation at each waste heat harvesting location on a vehicle. Optimal materials and TE couple configurations are suggested. Moreover, a comparison of prevailing DC-DC conversion techniques was made with respect to applications at each conversion level within the network. Furthermore, higher-level design considerations are discussed according to system specifications. Finally, a case study is performed to compare the performance of the proposed network and a traditional single-stage system. The results show that the proposed network enhances the system conversion efficiency by up to 400%.

  17. Light weight, high power, high voltage dc/dc converter technologies

    NASA Technical Reports Server (NTRS)

    Kraus, Robert; Myers, Ira; Baumann, Eric

    1990-01-01

    Power-conditioning weight reductions by orders of magnitude will be required to enable the megawatt-power-level space systems envisioned by the Strategic Defense Initiative, the Air Force, and NASA. An interagency program has been initiated to develop an 0.1-kg/kW dc/dc converter technology base for these future space applications. Three contractors are in the first phase of a competitive program to develop a megawatt dc/dc converter. Researchers at NASA Lewis Research Center are investigating innovative converter topology control. Three different converter subsystems based on square wave, resonant, and super-resonant topologies are being designed. The components required for the converter designs cover a wide array of technologies. Two different switches, one semiconductor and the other gas, are under development. Issues related to thermal management and material reliability for inductors, transformers, and capacitors are being investigated in order to maximize power density. A brief description of each of the concepts proposed to meet the goals of this program is presented.

  18. Microfabricated Thin-Film Inductors for High-Frequency DC-DC Power Conversion

    NASA Astrophysics Data System (ADS)

    Yao, Di

    2011-12-01

    Microfabricated V-groove inductors targeted to operate above 10 MHz are investigated. Multilayer nano-granular Co-Zr-O/ZrO2 magnetic thin films are used as the core material of the inductors to improve the magnetic performance of the films deposited on the sidewalls of V-grooves and to control eddy-current loss in the core, which goes up very quickly as frequency increases. A loss model is developed to estimate eddy-current loss in multilayer magnetic thin films considering the effect of displacement current at high frequencies, and the model is applied in the design of V-groove inductors. V-groove inductors using multilayer magnetic thin films are co-optimized with power MOSFETs for 7-V to 3.3-V, 1-A DC-DC buck converters to maximize power handling capability per unit substrate area for given efficiencies. Prototype V-groove inductors are fabricated based on the optimization results, and measured and predicted performance of the inductors match well. The prototype inductors are a promising candidate for high-power-density high-efficiency DC-DC converters. The 7-V to 3.3-V, 1-A converters using prototype V-groove inductors are expected to exhibit power density of 2.5 W/mm2 and efficiency of 86% at 100 MHz, and power density of 0.36 W/mm2 and efficiency of 91% at 11 MHz.

  19. A DC-DC converter based powering scheme for the upgrade of the CMS pixel detector

    NASA Astrophysics Data System (ADS)

    Feld, L.; Karpinski, W.; Klein, K.; Merz, J.; Sammet, J.; Wlochal, M.

    2011-11-01

    Around 2016, the pixel detector of the CMS experiment will be upgraded. The amount of current that has to be provided to the front-end electronics is expected to increase by a factor of two. Since the space available for cables is limited, this would imply unacceptable power losses in the currently installed supply cables. Therefore it is foreseen to place DC-DC converters close to the front-end electronics, allowing the provision of power at higher voltages, thereby facilitating the supply of the required currents with the present cable plant. This conference report introduces the foreseen powering scheme of the pixel upgrade. For the first time, system tests have been conducted with pixel barrel sensor modules, radiation tolerant DC-DC converters and the full power supply chain of the pixel detector. In addition, studies of the stability of different powering schemes under various conditions are summarized. In particular the impact of large and fast load variations, which are related to the bunch structure of the LHC beam, has been studied.

  20. Bifurcation Analysis of a DC-DC Bidirectional Power Converter Operating with Constant Power Loads

    NASA Astrophysics Data System (ADS)

    Cristiano, Rony; Pagano, Daniel J.; Benadero, Luis; Ponce, Enrique

    Direct current (DC) microgrids (MGs) are an emergent option to satisfy new demands for power quality and integration of renewable resources in electrical distribution systems. This work addresses the large-signal stability analysis of a DC-DC bidirectional converter (DBC) connected to a storage device in an islanding MG. This converter is responsible for controlling the balance of power (load demand and generation) under constant power loads (CPLs). In order to control the DC bus voltage through a DBC, we propose a robust sliding mode control (SMC) based on a washout filter. Dynamical systems techniques are exploited to assess the quality of this switching control strategy. In this sense, a bifurcation analysis is performed to study the nonlinear stability of a reduced model of this system. The appearance of different bifurcations when load parameters and control gains are changed is studied in detail. In the specific case of Teixeira Singularity (TS) bifurcation, some experimental results are provided, confirming the mathematical predictions. Both a deeper insight in the dynamic behavior of the controlled system and valuable design criteria are obtained.

  1. Double layer capacitor/DC-DC converter system applied to constant power loads

    SciTech Connect

    Spyker, R.L.; Nelms, R.M.

    1996-12-31

    Ultracapacitors or double layer capacitors are a recent technology based on the well-known electrochemical phenomenon of extremely high capacitance/unit area in an electrode-electrolyte interface and the high surface area achievable in activated carbon fibers. Capacitors have been tested with a rated capacitance value of 470 F and a rated voltage of 2.3 V. Test voltages as high as 3V (30% above rated) have been used without any short term effect on measured capacitance. At 3 V the total energy storage capacity of one capacitor is 2,100 Joules. With a total volume of 245 cm{sup 3}, the specific energy of this capacitor is 8.5 J/cm{sup 3}. To tap this entire energy store would require running the capacitor to zero voltage. Of course, few loads to which a capacitor bank might be connected can tolerate any drop in input voltage. To remedy this problem a DC/DC converter between the capacitor bank and load is proposed. This paper describes optimization of capacitor bank configurations when supplying a constant power load through a DC/DC converter.

  2. DC Self Bias Trends in Dual Frequency PECVD Deposition Systems

    NASA Astrophysics Data System (ADS)

    Keil, D. L.; Augustyniak, E.; Leeser, C.; Galli, F.

    2011-10-01

    Capacitively coupled plasma (CCP) etch systems commonly report the DC auto or self bias developed as a consequence of capacitively coupling RF to the plasma. Frequently, these systems employ wafer pedestals comprised of electrostatic chucks which must monitor the self bias as part of their normal operation. DC self bias is often found to correlate with various etch process behaviors or system states. It is less common, however, to find CCP deposition systems that report DC self bias. This work reports results of a study of DC self bias trends due to chamber pressure, chamber conditioning and aging, and changes in wafer pedestal hardware. In particular, chamber film accumulation is found to correlate to certain DC bias trends. The applicability of these results for process tracking and system monitoring is discussed. Additionally, the DC self bias response to deliberate perturbations to the RF system are examined. These perturbations include those not normally encountered during commercial deposition such as `bleeding' current to ground.

  3. Simulation of the dc Plasma in Carbon Nanotube Growth

    NASA Technical Reports Server (NTRS)

    Hash, David; Bose, Deepak; Govindan, T. R.; Meyyappan, M.; Biegel, Bryan (Technical Monitor)

    2003-01-01

    A model for the dc plasma used in carbon nanotube growth is presented, and one-dimensional simulations of an acetylene/ammonia/argon system are performed. The effect of dc bias is illustrated by examining electron temperature, electron and ion densities, and neutral densities. Introducing a tungsten filament in the dc plasma, as in hot filament chemical vapor deposition with plasma assistance, shows negligible influence on the system characteristics.

  4. Human DC-SIGN Binds Specific Human Milk Glycans

    PubMed Central

    Noll, Alexander J.; Yu, Ying; Lasanajak, Yi; Duska-McEwen, Geralyn; Buck, Rachael H.; Smith, David F.; Cummings, Richard D.

    2016-01-01

    Human milk glycans (HMGs) are prebiotics, pathogen receptor decoys, and regulators of host physiology and immune responses. Mechanistically, human lectins (glycan-binding proteins, hGBPs) expressed by dendritic cells (DC) are of major interest, as these cells directly contact HMGs. To explore such interactions, we screened many C-type lectins and Siglecs expressed by DC for glycan binding on microarrays presenting over 200 HMGs. Unexpectedly, DC-SIGN showed robust binding to many HMGs, whereas other C-type lectins failed to bind, and Siglecs-5 and -9 showed weak binding to a few glycans. By contrast, most hGBPs bound to multiple glycans on other microarrays lacking HMGs. An α-linked fucose residue was characteristic of HMGs bound by DC-SIGN. Binding of DC-SIGN to the simple HMGs 2′-fucosyllactose (2′-FL) and 3-fucosyllactose (3-FL) was confirmed by flow cytometry to beads conjugated with 2′-FL or 3-FL, as well as the ability of the free glycans to inhibit DC-SIGN binding. 2′-FL had an IC50 of ~1 mM for DC-SIGN, which is within the physiological concentration of 2′-FL in human milk. These results demonstrate that DC-SIGN among the many hGBPs expressed by DC binds to α-fucosylated HMGs, and suggest that such interactions may be important in influencing immune responses in the developing infant. PMID:26976925

  5. NASA DC-8 Airborne Scanning Lidar Sensor Development

    NASA Technical Reports Server (NTRS)

    Nielsen, Norman B.; Uthe, Edward E.; Kaiser, Robert D.; Tucker, Michael A.; Baloun, James E.; Gorordo, Javier G.

    1996-01-01

    The NASA DC-8 aircraft is used to support a variety of in-situ and remote sensors for conducting environmental measurements over global regions. As part of the atmospheric effects of aviation program (AEAP) the DC-8 is scheduled to conduct atmospheric aerosol and gas chemistry and radiation measurements of subsonic aircraft contrails and cirrus clouds. A scanning lidar system is being developed for installation on the DC-8 to support and extend the domain of the AEAP measurements. Design and objectives of the DC-8 scanning lidar are presented.

  6. NASA DC-8 airborne scanning LIDAR sensor development

    SciTech Connect

    Nielsen, N.B.; Uthe, E.E.; Kaiser, R.D.

    1996-11-01

    The NASA DC-8 aircraft is used to support a variety of in-situ and remote sensors for conducting environmental measurements over global regions. As part of the atmospheric effects of aviation program (AEAP) the DC-8 is scheduled to conduct atmospheric aerosol and gas chemistry and radiation measurements of subsonic aircraft contrails and cirrus clouds. A scanning lidar system is being developed for installation on the DC-8 to support and extend the domain of the AEAP measurements. Design and objectives of the DC-8 scanning lidar are presented. 4 figs.

  7. Maximum Power Point Tracking Controller for Thermoelectric Generators with Peak Gain Control of Boost DC-DC Converters

    NASA Astrophysics Data System (ADS)

    Park, Jungyong; Kim, Shiho

    2012-06-01

    An analog maximum power point tracking (MPPT) circuit for a thermoelectric generator (TEG) is proposed. We show that the peak point of the voltage conversion gain of a boost DC-DC converter with an input voltage source having an internal resistor is the maximum power point of the TEG. The key characteristic of the proposed MPPT controller is that the duty ratio of the input clock pulse to the boost DC-DC converter shifts toward the maximum power point of the TEG by seeking the peak gain point of the boost DC-DC converters. The proposed MPPT technique provides a simple and useful analog MPPT solution, without employing digital microcontroller units.

  8. DC to DC Converter Testing for Space Applications: Use of EMI Filters and Thermal Range of Operation

    NASA Technical Reports Server (NTRS)

    Leon, Rosa

    2008-01-01

    Several tests were performed on Interpoint and International Rectifier (IR) direct current (DC) to DC converters to evaluate potential performance and reliability issues in space use of DC to DC converters and to determine if the use of electromagnetic interference (EMI) filters mitigates concerns observed during previous tests. Test findings reported here include those done up until September - October 2008. Tests performed include efficiency, regulation, cross-regulation, power consumption with inhibit on, load transient response, synchronization, and turn-on tests. Some of the test results presented here span the thermal range -55 C to 125 C. Lower range was extended to -120 C in some tested converters. Determination of failure root cause in DC/DC converters that failed at thermal extremes is also included.

  9. Design of a 3/2 Step-Up SC DC-DC Converter for Diode-Lamps

    NASA Astrophysics Data System (ADS)

    Eguchi, Kei; Ueno, Fumio; Inoue, Takahiro

    Aiming an IC implementation of a DC-DC converter which can provide a 4.5˜5 V stepped-up voltage for diode-lamps, a switched-capacitor (SC) DC-DC converter is proposed in this paper. Different from a conventional approach employing doubler circuits, the proposed circuit provides the output voltage by achieving a 3/2 step-up conversion. Therefore, decline in power efficiency for the proposed circuit is gentle. The process of DC-DC conversion is analyzed theoretically. To confirm the validity of the circuit design, SPICE simulations are performed. For the input voltage 3.2˜4.5 V, the power efficiency is 73˜92 % in the output current about 150 mA.

  10. ASIC and FPGA based DPWM architectures for single-phase and single-output DC-DC converter: a review

    NASA Astrophysics Data System (ADS)

    Chander, Subhash; Agarwal, Pramod; Gupta, Indra

    2013-12-01

    Pulse width modulation (PWM) has been widely used in power converter control. This paper presents a review of architectures of the Digital Pulse Width Modulators (DPWM) targeting digital control of switching DC-DC converters. An attempt is made to review the reported architectures with emphasis on the ASIC and FPGA implementations in single phase and single-output DC-DC converters. Recent architectures using FPGA's advanced resources for achieving the resolution higher than classical methods have also been discussed. The merits and demerits of different architectures, and their relative comparative performance, are also presented. The Authors intention is to uncover the groundwork and the related references through this review for the benefit of readers and researchers targeting different DPWM architectures for the DC-DC converters.

  11. Airframe noise of the DC-9

    NASA Technical Reports Server (NTRS)

    Bauer, A. B.; Munson, A. G.

    1977-01-01

    Airframe noise measurements are reported for the DC-9-31 aircraft flown at several speeds and with a number of flap, landing gear, and slat extension configurations. The data are corrected for atmospheric attenuation and spherical divergence, and are presented for an overhead position normalized to a 1-meter height. The sound pressure levels are found to vary approximately as the fifth power of flight velocity. Both lift and drag dipoles exist as a significant part of the airframe noise. The data are compared with airframe noise predictions using the drag element and the data analysis methods. Although some of the predictions are very good, further work is needed to refine these methods, particularly for the gear-down and flaps-down configurations.

  12. Artificial Intelligent Controller for a DC Motor

    NASA Astrophysics Data System (ADS)

    Delavari, Hadi; Ranjbar Noiey, Abolzafl; Minagar, Sara

    The Speed and position control of DC motors is addressed in this paper. An optimal intelligent control scheme is proposed for the system. Preliminary a PID controller is designed using Genetic Algorithms (GA). The proposed controller is implemented by using optimal integral state feedback control with GA and Kalman filter. In the proposed scheme, performance depends on choosing weighting matrices Q and R in the cost function, and accordingly GA is used to find these proper weighting matrices. In order to reduce the control performance degradation due to system parameters variation, a Kalman filter is gained. The performance of the proposed technique (ISF) is compared with PID controller. Computer simulation validates the effectiveness of the proposed scheme even in presence of uncertainties.

  13. dc glow-discharge cleaning for accelerator

    SciTech Connect

    Chou, T.S.; Hseuh, H.C.

    1982-01-01

    Average pressure of 1 x 10/sup -11/ torr and vacuum stability are necessary for the successful operation of the proton storage rings such as ISABELLE. Vacuum degassing at high temperature and in situ bake-out will reduce the thermoout-gassing rate of the beam tubes to approx. 10/sup -13/ Tl/cm/sup 2/ sec, therefore achieving the required static pressure. The vacuum instability caused by beam-induced ion desorption can be solved by dc glow discharge cleaning. With evidence from this study, the present understanding of glow discharge in a cylindrically symmetric geometry is reviewed. Argon and argon/oxygen mixture serve as plasmas in the glow. The role of oxygen in cleaning the beam tubes during the glow discharge is demonstrated experimentally. Glow discharge cleaning with and without bake-out is also studied.

  14. Electronically commutated dc motors for electric vehicles

    NASA Technical Reports Server (NTRS)

    Maslowski, E. A.

    1981-01-01

    A motor development program to explore the feasibility of electronically commutated dc motors (also known as brushless) for electric cars is described. Two different design concepts and a number of design variations based on these concepts are discussed. One design concept is based on a permanent magnet, medium speed, machine rated at 7000 to 9000 rpm, and powered via a transistor inverter power conditioner. The other concept is based on a permanent magnet, high speed, machine rated at 22,000 to 26,000 rpm, and powered via a thyristor inverter power conditioner. Test results are presented for a medium speed motor and a high speed motor each of which have been fabricated using samarium cobalt permanent magnet material.

  15. Properties of dc helicity injected tokamak plasmas

    SciTech Connect

    Darrow, D.S.; Ono, M.; Forest, C.B.; Greene, G.J.; Hwang, Y.S.; Park, H.K. ); Taylor, R.J.; Pribyl, P.A.; Evans, J.D.; Lai, K.F.; Liberati, J.R. )

    1990-06-01

    Several dc helicity injection experiments using an electron beam technique have been conducted on the Current Drive Experiment (CDX) (Phys. Rev. Lett. {bold 59}, 2165 (1987)) and the Continuous Current Tokamak (CCT) (Phys. Rev. Lett. {bold 63}, 2365 (1989)). The data strongly suggest that tokamak plasmas are being formed and maintained by this method. The largest currents driven to date are 1 kA in CDX ({ital q}{sub {ital a}} =5) and 6 kA in CCT ({ital q}{sub {ital a}} =3.5). An initial comparison of discharge properties with helicity theory indicates rough agreement. Current drive energy efficiencies are 9% and 23% of Ohmic efficiency in two cases analyzed. Strong radial electric fields are observed in these plasmas that cause poloidal rotation and, possibly, improved confinement.

  16. Electronically commutated dc motors for electric vehicles

    NASA Astrophysics Data System (ADS)

    Maslowski, E. A.

    A motor development program to explore the feasibility of electronically commutated dc motors (also known as brushless) for electric cars is described. Two different design concepts and a number of design variations based on these concepts are discussed. One design concept is based on a permanent magnet, medium speed, machine rated at 7000 to 9000 rpm, and powered via a transistor inverter power conditioner. The other concept is based on a permanent magnet, high speed, machine rated at 22,000 to 26,000 rpm, and powered via a thyristor inverter power conditioner. Test results are presented for a medium speed motor and a high speed motor each of which have been fabricated using samarium cobalt permanent magnet material.

  17. Dissipative Cryogenic Filters with Zero DC Resistance

    SciTech Connect

    Bluhm, Hendrik; Moler, Kathryn A.; /Stanford U., Appl. Phys. Dept

    2008-04-22

    The authors designed, implemented and tested cryogenic RF filters with zero DC resistance, based on wires with a superconducting core inside a resistive sheath. The superconducting core allows low frequency currents to pass with negligible dissipation. Signals above the cutoff frequency are dissipated in the resistive part due to their small skin depth. The filters consist of twisted wire pairs shielded with copper tape. Above approximately 1 GHz, the attenuation is exponential in {radical}{omega}, as typical for skin depth based RF filters. By using additional capacitors of 10 nF per line, an attenuation of at least 45 dB above 10 MHz can be obtained. Thus, one single filter stage kept at mixing chamber temperature in a dilution refrigerator is sufficient to attenuate room temperature black body radiation to levels corresponding to 10 mK above about 10 MHz.

  18. DC SQUID Phase Qubit with LC Filter

    NASA Astrophysics Data System (ADS)

    Kwon, Hyeokshin; Przybysz, A. J.; Paik, Hanhee; Lewis, R. M.; Palomaki, T. A.; Dutta, S. K.; Cooper, B. K.; Anderson, J. R.; Lobb, C. J.; Wellstood, F. C.

    2008-03-01

    We investigate the use of an inductor-capacitor (LC) network to increase the isolation of a dc SQUID phase qubit from its current bias leads and thereby increase the dissipation time T1 and coherence time T2. One junction in the SQUID acts as an ideal phase qubit while the second junction and the SQUID loop inductance act as a broadband filter to isolate the first junction from the current bias leads. The LC-isolation network provides an additional isolation factor and allows flexibility in the choice of SQUID parameters. In addition to increasing the isolation from the leads, our design minimizes the effects of dielectric loss and two-level systems by using a relatively small Josephson junction, building the devices from Al/Al2O3/Al on sapphire, and only using insulating layers (SiNx) in external capacitors for the phase qubit junction and LC network. *Funding provided by JQI, CNAM and the DOD.

  19. Ion Velocimetry In Magnetized DC Sheaths

    NASA Astrophysics Data System (ADS)

    Young, Christopher; Lucca Fabris, Andrea; Cappelli, Mark

    2013-09-01

    Particle dynamics near the magnetic cusps in cusped field plasma thrusters are still not well understood; characterizing the ion velocity distribution functions in these regions can help thruster designs maximize electron trapping and minimize erosion of the channel wall. To that end, a robust argon ion velocity sensor is developed using a three-level laser-induced fluorescence (LIF) technique. The 3d4F7 / 2 --> 4p4D5/ 2 0 ArII transition at 668.61 nm is pumped with a 25 mW tunable external cavity diode laser, and fluorescence down to the 4s4P3 / 2 state at 442.72 nm is collected with phase-sensitive detection. The Doppler shift in the acquired signal peak, compared to a stationary reference, gives the ion velocity component parallel to the exciting laser. We demonstrate this LIF scheme by obtaining the argon ion velocity profile through a magnetized DC sheath. The LIF measurement is used to validate a new optogalvanic velocimetry technique in which two lasers (chopped at different frequencies) intersect one another at 90° in the measurement volume. Using a lock-in amplifier, changes observed in the DC discharge current at the sum and difference of the two chopping frequencies may be related back to the mean ion velocity at that point. The authors acknowledge support from the Air Force Office of Scientific Research (AFOSR). CY acknowledges support from the DOE NNSA Stewardship Science Graduate Fellowship under contract DE-FC52-08NA28752.

  20. Temperature in HFETs when operating in DC

    NASA Astrophysics Data System (ADS)

    Gonzalez, Benito; Hernandez, Antonio; Garcia, Javier; del Pino, F. J.; Nunez, Antonio; Sendra, Jose R.

    2003-04-01

    This work analyses the DC response of an InGaAs channel PHFET when varying temperature. An analytic model for the drain current is derived from previous work, incorporating the extrinsic resistances. Experimental output characteristics at different temperatures are compared with those offered by the resulting model and numerical simulations. The DC drain current is obtained introducing the external voltages applied to the HFET terminals into an intrinsic model. The temperature range considered in this paper is between 300 and 400 K. In this range, the temperature dependence of the intrinsic electrical parameters is included in the model. For the temperature dependence of the extrinsic resistances, the HFET is numerically simulated with MINIMOS-NT. As far as we know, any influence of the electron transport through the AlGaAs/InGaAs heterojunction on the extrinsic resistances has not been already established. In our case, a termionic-field-emission (TFE) is used to simulate this effect (without TFE not only the drain current is underestimated, but also the temperature dependence predicted is opposite to the actual). As result, the extrinsic source resistence is nearly constant (7.5 ohms), and higher values are obtained for the extrinsic drain resistence, which has a linear and positive temperature dependence, raising as the transistor operates in saturation region. When the drain voltage diminishes, the influence of the TFE model on the extrinsic resistances vanishes, and RD tends to RS. The drain current predicted by the model, in linear and saturation region, shows a relative error between measured and modeled values smaller than 10%.

  1. A Reduced-Part, Triple-Voltage DC-DC Converter for EV/HEV Power Management

    SciTech Connect

    Su, Gui-Jia; Tang, Lixin

    2009-01-01

    Electrical power systems in future hybrid and fuel cell vehicles may consist of three voltage nets: 14 V, 42 V, and high voltage (>200 V) buses. A soft-switched, bidirectional dc-dc converter that uses only four switches was proposed for interconnecting the three nets. This paper presents a reduced-part dc-dc converter, which decreases the converter cost while retaining all the favorable features of the original topology. Experimental data are included to verify a simple power flow control scheme.

  2. High-Voltage 1-kW dc/dc Converter Developed for Low-Temperature Operation

    NASA Technical Reports Server (NTRS)

    Patterson, Richard L.

    1998-01-01

    Recently, Lewis developed and demonstrated a high-voltage, 1-kW dc/dc converter that operates from room temperature to -184 C. A power supply designed for use in a NASA ion beam propulsion system was utilized as a starting point for the design of a low- (wide-) temperature dc/dc converter. For safety, we decided to halve the output voltage and power level, so the converter was designed for an 80-Vdc input and a 550-Vdc output at 1 kW.

  3. Association of DC-SIGN and DC-SIGNR Repeat Regions with Susceptibility to Pulmonary Tuberculosis in Zahedan, Southeastern Iran.

    PubMed

    Naderi, Mohammad; Hashemi, Mohammad; Soroush, Navid; Amininia, Shadi; Taheri, Mohsen

    2016-05-01

    There are conflicting results concerning DC-SIGN and DC-SIGNR VNTR polymorphisms. The present study aimed to evaluate the possible association between DC-SIGN as well as DC-SIGNR VNTR polymorphisms and pulmonary tuberculosis (PTB) in a sample of Iranian population. This case-control study was done on 171 PTB and 161 healthy subjects. The variants were detected by polymerase chain reaction (PCR). DC-SIGNR VNTR genotypes in cases were 12.7% for 5/5, 2.4% for 6/5, 32.7% for 7/7, 38.2% for 7/5, 5.5% for 7/6, 1.2% for /5, 0.6% for 9/6, 6.7% for 9/7 in PTB patients and 19.7% for 5/5, 2.0% for 6/5, 31.6% for 7/7, 37.5% for 7/5, 5.7% for 7/6, 0.0% for 9/5, 0.7% for 9/6, 2.6% for 9/7 in controls. The findings showed no significant association between DC-SIGNR VNTR polymorphism and PTB. All subjects in cases and controls were 7/7 genotype regarding DC-SIGN VNTR polymorphism. Our data propose that DC-SIGNR VNTR, as well as DC-SIGN VNTR, were not associated with the risk of PTB in a sample of Iranian population. PMID:27309478

  4. Low-temperature operation of a Buck DC/DC converter

    NASA Technical Reports Server (NTRS)

    Ray, Biswajit; Gerber, Scott S.; Patterson, Richard L.; Myers, Ira T.

    1995-01-01

    Low-temperature (77 K) operation of a 42/28 V, 175 W, 50 kHz PWM Buck DC/DC converter designed with commercially available components is reported. Overall, the converter losses decreased at 77 K compared to room temperature operation. A full-load efficiency of 97 percent was recorded at liquid-nitrogen temperature, compared to 95.8 percent at room temperature. Power MOSFET operation improved significantly where as the output rectifier operation deteriorated at low-temperature. The performance of the output filter inductor and capacitor did not change significantly at 77 K compared to room temperature performance. It is possible to achieve high-density and high efficiency power conversion at low-temperatures due to improved electronic, electrical and thermal properties of materials.

  5. The 25 kW resonant dc/dc power converter

    NASA Technical Reports Server (NTRS)

    Robson, R. R.

    1983-01-01

    The feasibility of processing 25-kW of power with a single, transistorized, series resonant converter stage was demonstrated by the successful design, development, fabrication, and testing of such a device which employs four Westinghouse D7ST transistors in a full-bridge configuration and operates from a 250-to-350 Vdc input bus. The unit has an overall worst-case efficiency of 93.5% at its full rated output of 1000 V and 25 A dc. A solid-state dc input circuit breaker and output-transient-current limiters are included in and integrated into the design. Full circuit details of the converter are presented along with the test data.

  6. Analysis of Discontinuity Induced Bifurcations in a Dual Input DC-DC Converter

    NASA Astrophysics Data System (ADS)

    Giaouris, Damian; Banerjee, Soumitro; Mandal, Kuntal; Al-Hindawi, Mohammed M.; Abusorrah, Abdullah; Al-Turki, Yusuf; El Aroudi, Abdelali

    DC-DC power converters with multiple inputs and a single output are used in numerous applications where multiple sources, e.g. two or more renewable energy sources and/or a battery, feed a single load. In this work, a classical boost converter topology with two input branches connected to two different sources is chosen, with each branch independently being controlled by a separate peak current mode controller. We demonstrate for the first time that even though this converter is similar to other well known topologies that have been studied before, it exhibits many complex nonlinear behaviors that are not found in any other standard PWM controlled power converter. The system undergoes period incrementing cascade as a parameter is varied, with discontinuous hard transitions between consecutive periodicities. We show that the system can be described by a discontinuous map, which explains the observed bifurcation phenomena. The results have been experimentally validated.

  7. Performance of a spacecraft DC-DC converter breadboard modified for low temperature operation

    NASA Technical Reports Server (NTRS)

    Gerber, Scott S.; Stell, Chris; Patterson, Richard; Ray, Biswajit

    1996-01-01

    A 1OW 3OV/5.OV push-pull dc-dc converter breadboard, designed by the Jet Propulsion Laboratory (JPL) with a +50 C to +5 C operating range for the Cassini space probe, was characterized for lower operating temperatures. The breadboard converter which failed to operate for temperatures below -125 C was then modified to operate at temperatures approaching that of liquid nitrogen (LN2). Associated with this low operating temperature range (greater than -196 C) was a variety of performance problems such as significant change in output voltage, converter switching instability, and failure to restart at temperatures below -154 C. An investigation into these problems yielded additional modifications to the converter which improved low temperature performance even further.

  8. A Compact, Soft-Switching DC-DC Converter for Electric Propulsion

    NASA Technical Reports Server (NTRS)

    Button, Robert; Redilla, Jack; Ayyanar, Raja

    2003-01-01

    A hybrid, soft-switching, DC-DC converter has been developed with superior soft switching characteristics, high efficiency, and low electro-magnetic interference. This hybrid topology is comprised of an uncontrolled bridge operating at full pulse-width, and a controlled section operating as a conventional phase modulated converter. The unique topology is able to maintain zero voltage switching down to no load operating conditions. A breadboard prototype was developed and tested to demonstrate the benefits of the topology. Improvements were then made to reduce the size of passive components and increase efficiency in preparation for packaging. A packaged prototype was then designed and built, and several innovative packaging techniques are presented. Performance test data is presented that reveals deficiencies in the design of the power transformer. A simple redesign of the transformer windings eliminated the deficiency. Future plans to improve the converter and packaging design are presented along with several conclusions.

  9. SSP Technology Investigation of a High-Voltage DC-DC Converter

    NASA Technical Reports Server (NTRS)

    Pappas, J. A.; Grady, W. M.; George, Patrick J. (Technical Monitor)

    2002-01-01

    The goal of this project was to establish the feasibility of a high-voltage DC-DC converter based on a rod-array triggered vacuum switch (RATVS) for the Space Solar Power system. The RATVS has many advantages over silicon and silicon-carbide devices. The RATVS is attractive for this application because it is a high-voltage device that has already been demonstrated at currents in excess of the requirement for an SSP device and at much higher per-device voltages than existing or near-term solid state switching devices. The RATVS packs a much higher specific power rating than any solid-state device and it is likely to be more tolerant of its surroundings in space. In addition, pursuit of an RATVS-based system would provide NASA with a nearer-term and less expensive power converter option for the SSP.

  10. Low Temperature Performance of High Power Density DC/DC Converter Modules

    NASA Technical Reports Server (NTRS)

    Elbuluk, Malik E.; Hammond, Ahmad; Gerber, Scott; Patterson, Richard L.; Overton, Eric

    2001-01-01

    In this paper, two second-generation high power density DC/DC converter modules have been evaluated at low operating temperatures. The power rating of one converter (Module 1) was specified at 150 W with an input voltage range of 36 to 75 V and output voltage of 12 V. The other converter (Module 2) was specified at 100 W with the same input voltage range and an output voltage of 3.3 V. The converter modules were evaluated in terms of their performance as a function of operating temperature in the range of 25 to -140 C. The experimental procedures along with the experimental data obtained are presented and discussed in this paper.

  11. Inverse dual converter (IDC) for high power dc-dc applications

    NASA Astrophysics Data System (ADS)

    Ehsani, M.; Husain, I.; Bilgic, M. O.

    The inverse dual converter (IDC), suitable for high-power dc-dc conversion applications, is presented. The IDC is a voltage source converter with an ac link and has been derived from an inductor converter bridge. This capacitor commutated converter is capable of continuous voltage step-up or step-down control over a wide range without the need of a transformer. In addition to high-frequency switching the converter is characterized by soft switching techniques, reducing constraints on the ratings of the switches. The average model developed with the help of gyrator theory provides sufficient information for control strategies and design considerations. The results of gyrator modeling and computer simulation are compared with experimental results obtained from a prototype IDC.

  12. DC-DC converters in 0.35μm CMOS technology

    NASA Astrophysics Data System (ADS)

    Michelis, S.; Allongue, B.; Blanchot, G.; Faccio, F.; Fuentes, C.; Orlandi, S.; Saggini, S.; Cengarle, S.; Ongaro, F.

    2012-01-01

    In view of the upgrade of the LHC experiments, we are developing custom DC/DC converters for a more efficient power distribution scheme. A new prototype have been integrated in ASICs in the selected 0.35μm commercial high voltage technology that has been successfully tested for all radiation effects: TID, displacement damage and Single Event Burnout. This converter has been optimized for high efficiency and improved radiation tolerance. Amongst the new features the most relevant are the presence of internal linear regulators, protection circuits with a state-machine and a new pinout for a modified assembly in package in order to reduce conductive losses. This paper illustrates the design of the prototype followed by functional and radiation tests.

  13. High efficiency interleaved bi-directional ZVS DC-DC converter

    NASA Astrophysics Data System (ADS)

    Zafarullah Khan, M.; Mohsin Naveed, M.; Akbar Hussain, D. M.

    2013-06-01

    A high efficiency interleaved bi-directional ZVS DC-DC converter is presented in this paper. This converter can be operated in both buck and boost mode. CoolMOS is used as a power device to achieve low conduction losses and fast turn off. The value of inductance is selected such that the CoolMOS drain-to-source voltage always falls to zero before it turns on and ZVS is achieved. Multiphase interleaved inductors are used to achieve high power and low ripple currents. Converter is operated at 50kHz and MATLAB Simulink simulation is performed. 6kW prototype converter is implemented in buck mode and simulation results are verified.

  14. Practical Design Guidelines of qZSI Based Step-Up DC/DC Converter

    NASA Astrophysics Data System (ADS)

    Zakis, Janis; Vinnikov, Dmitri; Roasto, Indrek; Jalakas, Tanel

    2010-01-01

    This paper presents some design guidelines for a new voltage fed step-up DC/DC isolated converter. The most significant advantage of proposed converter is voltage buck-boost operation on single stage. The most promising application for proposed converter is in the field of distributed power generation e.g. fuel cells or photovoltaic. The most sensitive issues - such as power losses caused by high currents in the input side of converter and high transient overvoltages across the inverter bridge caused by stray inductances were discussed and solved. The proposals and recommendations to overcome these issues are given in the paper. The Selection and design guidelines of converter elements are proposed and explained. The prototype of proposed converter was built and experimentally tested. Some results are presented and evaluated.

  15. Topological variations of the inverse dual converter for high-power dc-dc distribution systems

    NASA Astrophysics Data System (ADS)

    Ehsani, Mehrdad; Laskai, Laszlo

    New dc-to-dc converter topologies are presented which are suitable for high density high power supplies. Topological variations of the basic inverse dual converter (IDC) circuit such as the transformer coupled, the multiphase and the multipulse derivation of the single phase IDC have been analyzed and some simulation results have been presented. The single phase IDC offers a buck-boost operation over wide range without transformer, bidirectional power flow, and complementary commutation of the switches. The topologies examined in this paper have additional features such as lower device and component stresses, and smaller filter requirements, resulting in smaller size and weight. Some performance and possible applications are also examined. IDCs for serial and parallel power distribution, and ac tapping of the IDC are discussed.

  16. Table-aided design of the energy-storage reactor in dc-to-dc converters

    NASA Technical Reports Server (NTRS)

    Owen, H. A., Jr.

    1975-01-01

    A new procedure for the selection of magnetic cores for use in energy-storage dc-to-dc power converters which eliminates the need for an automated computer search algorithm and stored data file is presented. The converter configurations included in the procedure are the three commonly encountered single-winding converters for voltage step-up, for current step-up and for voltage step-up/current step-up, and for the two-winding converter for voltage step-up/current step-up. For each converter configuration, three types of controllers are considered - constant-frequency, constant on-time and constant off-time. Using concepts developed from analyses of these converters by considering the transfer of energy by means of an energy-storage inductor or transformer, a special table of parameters calculated from magnetic core data is constructed and leads to a considerably simplified design procedure.

  17. Test and Treat DC: Forecasting the Impact of a Comprehensive HIV Strategy in Washington DC

    PubMed Central

    Walensky, Rochelle P.; Paltiel, A. David; Losina, Elena; Morris, Bethany L.; Scott, Callie A.; Rhode, Erin R.; Seage, George R.; Freedberg, Kenneth A.

    2010-01-01

    Background US and international agencies have signaled their commitment to containing the HIV epidemic via early case identification and linkage to antiretroviral therapy (ART) immediately upon diagnosis. We forecast outcomes of this approach if implemented in Washington DC. Methods Using a mathematical model of HIV case detection and treatment, we evaluate combinations of HIV screening and ART initiation strategies. We define current practice as no regular screening program and ART at ≤350/μl, and test and treat as annual screening and ART upon diagnosis. Outcomes include life expectancy of HIV-infected persons and changes in the population time with transmissible HIV RNA. Data, largely from DC, include undiagnosed HIV prevalence 0.6%, annual incidence 0.13%, 31% test offer, 60% acceptance, and 50% linkage to care. Input parameters, including optimized ART efficacy, are varied in sensitivity analyses. Results Projected life expectancies, from an initial mean age 41 years, for current practice, test and treat, and test and treat with optimized ART are 23.9, 25.0, and 25.6 years. Compared to current practice, test and treat leads to a 14.7% reduction in time spent with transmissible HIV RNA in the next 5 years; test and treat with optimized ART results in a 27.2% reduction. Conclusions An expanded HIV test and treat program in Washington DC will increase life expectancy of HIV-infected patients but will have a modest impact on HIV transmission over the next five years and is unlikely to halt the HIV epidemic. Summary The CEPAC model shows a test and treat strategy in Washington DC would result in a substantial clinical impact to HIV-infected individuals. Results suggest a need to temper expectations regarding the extent to which test and treat will control the epidemic. PMID:20617921

  18. Design of piezoelectric transformer for DC/DC converter with stochastic optimization method

    NASA Astrophysics Data System (ADS)

    Vasic, Dejan; Vido, Lionel

    2016-04-01

    Piezoelectric transformers were adopted in recent year due to their many inherent advantages such as safety, no EMI problem, low housing profile, and high power density, etc. The characteristics of the piezoelectric transformers are well known when the load impedance is a pure resistor. However, when piezoelectric transformers are used in AC/DC or DC/DC converters, there are non-linear electronic circuits connected before and after the transformer. Consequently, the output load is variable and due to the output capacitance of the transformer the optimal working point change. This paper starts from modeling a piezoelectric transformer connected to a full wave rectifier in order to discuss the design constraints and configuration of the transformer. The optimization method adopted here use the MOPSO algorithm (Multiple Objective Particle Swarm Optimization). We start with the formulation of the objective function and constraints; then the results give different sizes of the transformer and the characteristics. In other word, this method is looking for a best size of the transformer for optimal efficiency condition that is suitable for variable load. Furthermore, the size and the efficiency are found to be a trade-off. This paper proposes the completed design procedure to find the minimum size of PT in need. The completed design procedure is discussed by a given specification. The PT derived from the proposed design procedure can guarantee both good efficiency and enough range for load variation.

  19. Development of a Novel Bi-Directional Isolated Multiple-Input DC-DC Converter

    SciTech Connect

    Li, H.

    2005-10-24

    There is vital need for a compact, lightweight, and efficient energy-storage system that is both affordable and has an acceptable cycle life for the large-scale production of electric vehicles (EVs) and hybrid electric vehicles (HEVs). Most of the current research employs a battery-storage unit (BU) combined with a fuel cell (FC) stack in order to achieve the operating voltage-current point of maximum efficiency for the FC system. A system block diagram is shown in Fig.1.1. In such a conventional arrangement, the battery is sized to deliver the difference between the energy required by the traction drive and the energy supplied by the FC system. Energy requirements can increase depending on the drive cycle over which the vehicle is expected to operate. Peak-power transients result in an increase of losses and elevated temperatures which result in a decrease in the lifetime of the battery. This research will propose a novel two-input direct current (dc) dc to dc converter to interface an additional energy-storage element, an ultracapacitor (UC), which is shown in Fig.1.2. It will assist the battery during transients to reduce the peak-power requirements of the battery.

  20. Performance of a Voltage Step-Up/Step-Down Transformerless DC/DC Converter: Analytical Model

    NASA Astrophysics Data System (ADS)

    Suskis, P.; Rankis, I.

    2012-01-01

    The authors present an analytical model for a voltage step-up/step-down DC/DC converter without transformers. The proposed topology is a combination of classic buck and boost converters in one single circuit but with differing operational principles. The converter is developed for a wind power autonomous supply system equipped with a hydrogen electrolytic tank and a fuel cell for energy stabilization. The main power source of the hydrogen-based autonomous supply system is energized by a synchronous generator operating on permanent magnets and equipped with a diode bridge. The input voltage of the converter in this case varies in the range 0-700 V, while its output DC voltage must be 540 V according to the demand of other parts of the system. To maintain the rated voltage, a special electrical load regulation is introduced. The calculations of the converter, the generator (equipped with a diode bridge) as element of the power system supply joint, and the load replaced by resistance are verified with PSIM software.

  1. Multiphase High-Frequency Isolated DC-DC Converter for Industrial Applications

    NASA Astrophysics Data System (ADS)

    Maurya, Rakesh; Srivastava, S. P.; Agarwal, Pramod

    2014-01-01

    Industrial applications such as welding, plasma cutting, and surface hardening require a large DC current at low voltage. In such applications, the rating of power supply varies from few kilowatts to hundreds of kilowatts. The power supply employs in such applications particularly in arc welding process is expected to operate from open-circuit (no-load) to short-circuit (when the electrode sticks to the workpiece for a short span of time) quickly. In this paper, high-frequency isolated multiphase DC-DC converter is proposed which is well suited for aforementioned applications. Based on mathematical analysis, a simulation study with 5 kW, 5 V/1,000 A proposed model is carried out using Simulink block set and Sim Power System tool box and its performances are evaluated under symmetrical control methods. To verify the simulation results, scaled prototype model of rating 1.5 V/100 A is developed and tested with aforementioned control method under different operating conditions. In comparison with conventional welding power supply employed in many industries, the performance of proposed converter is improved significantly in terms of size and weight, efficiency and dynamic response.

  2. 77 FR 25781 - Environmental Impact Statement; Washington, DC

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-05-01

    ... Federal Highway Administration Environmental Impact Statement; Washington, DC AGENCY: U.S. Federal Highway... of Intent to Prepare a Draft Environmental Impact Statement (DEIS). SUMMARY: The U.S. Federal Highway... Washington, DC is issuing this notice to advise agencies and the public that a Draft Environmental...

  3. The Proving Grounds: School "Rheeform" in Washington, D.C.

    ERIC Educational Resources Information Center

    Dingerson, Leigh

    2010-01-01

    Washington, D.C., is leading the transformation of urban public education across the country--at least according to "Time" magazine, which featured D.C. Schools Chancellor Michelle Rhee on its cover, wearing black and holding a broom. But there is nothing remarkably visionary going on in Washington. The model of school reform that is being…

  4. Read-out electronics for DC squid magnetic measurements

    DOEpatents

    Ganther, Jr., Kenneth R.; Snapp, Lowell D.

    2002-01-01

    Read-out electronics for DC SQUID sensor systems, the read-out electronics incorporating low Johnson noise radio-frequency flux-locked loop circuitry and digital signal processing algorithms in order to improve upon the prior art by a factor of at least ten, thereby alleviating problems caused by magnetic interference when operating DC SQUID sensor systems in magnetically unshielded environments.

  5. 38 CFR 3.851 - St. Elizabeths Hospital, Washington, DC.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 38 Pensions, Bonuses, and Veterans' Relief 1 2014-07-01 2014-07-01 false St. Elizabeths Hospital, Washington, DC. 3.851 Section 3.851 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS AFFAIRS... Institutional Awards § 3.851 St. Elizabeths Hospital, Washington, DC. Benefits due or becoming due any...

  6. 38 CFR 3.851 - St. Elizabeths Hospital, Washington, DC.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 38 Pensions, Bonuses, and Veterans' Relief 1 2012-07-01 2012-07-01 false St. Elizabeths Hospital, Washington, DC. 3.851 Section 3.851 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS AFFAIRS... Institutional Awards § 3.851 St. Elizabeths Hospital, Washington, DC. Benefits due or becoming due any...

  7. 38 CFR 3.851 - St. Elizabeths Hospital, Washington, DC.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 38 Pensions, Bonuses, and Veterans' Relief 1 2013-07-01 2013-07-01 false St. Elizabeths Hospital, Washington, DC. 3.851 Section 3.851 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS AFFAIRS... Institutional Awards § 3.851 St. Elizabeths Hospital, Washington, DC. Benefits due or becoming due any...

  8. Integrated-Circuit Controller For Brushless dc Motor

    NASA Technical Reports Server (NTRS)

    Le, Dong Tuan

    1994-01-01

    Generic circuit performs commutation-logic and power-switching functions for control of brushless dc motor. Controller includes commutation-logic and associated control circuitry, power supply, and inverters containing power transistors. Major advantages of controller are size, weight, and power consumption can be made less than other brushless-dc-motor controllers.

  9. 36 CFR 910.13 - Urban design of Washington, DC.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ..., DC. 910.13 Section 910.13 Parks, Forests, and Public Property PENNSYLVANIA AVENUE DEVELOPMENT... PENNSYLVANIA AVENUE DEVELOPMENT AREA Urban Planning and Design Concerns § 910.13 Urban design of Washington, DC... legacy of the L'Enfant Plan, the primary function of new development in the Development Area is to...

  10. Historical Material Analysis of DC745U Pressure Pads

    SciTech Connect

    Ortiz-Acosta, Denisse

    2012-07-30

    As part of the Enhance Surveillance mission, it is the goal to provide suitable lifetime assessment of stockpile materials. This report is an accumulation of historical publication on the DC745U material and their findings. It is the intention that the B61 LEP program uses this collection of data to further develop their understanding and potential areas of study. DC745U is a commercially available silicone elastomer consisting of dimethyl, methyl-phenyl, and methyl-vinyl siloxane repeat units. Originally, this material was manufactured by Dow Corning as Silastic{reg_sign} DC745U at their manufacturing facility in Kendallville, IN. Recently, Dow Corning shifted this material to the Xiameter{reg_sign} brand product line. Currently, DC745U is available through Xiameter{reg_sign} or Dow Corning's distributor R. D. Abbott Company. DC745U is cured using 0.5 wt% vinyl-specific peroxide curing agent known as Luperox 101 or Varox DBPH-50. This silicone elastomer is used in numerous parts, including two major components (outer pressure pads and aft cap support) in the W80 and as pressure pads on the B61. DC745U is a proprietary formulation, thus Dow Corning provides limited information on its composition and properties. Based on past experience with Dow Corning, DC745U is at risk of formulation changes without notification to the costumer. A formulation change for DC745U may have a significant impact because the network structure is a key variable in determining material properties. The purpose of this report is to provide an overview of historical DC745U studies and identify gaps that need to be addressed in future work. Some of the previous studies include the following: 1. Spectroscopic characterization of raw gum stock. 2. Spectroscopic, thermal, and mechanical studies on cured DC745U. 3. Nuclear Magnetic Resonance (NMR) and solvent swelling studies on DC745U with different crosslink densities. 4. NMR, solvent swelling, thermal, and mechanical studies on thermally aged

  11. DC-SIGN(+) Macrophages Control the Induction of Transplantation Tolerance.

    PubMed

    Conde, Patricia; Rodriguez, Mercedes; van der Touw, William; Jimenez, Ana; Burns, Matthew; Miller, Jennifer; Brahmachary, Manisha; Chen, Hui-ming; Boros, Peter; Rausell-Palamos, Francisco; Yun, Tae Jin; Riquelme, Paloma; Rastrojo, Alberto; Aguado, Begoña; Stein-Streilein, Joan; Tanaka, Masato; Zhou, Lan; Zhang, Junfeng; Lowary, Todd L; Ginhoux, Florent; Park, Chae Gyu; Cheong, Cheolho; Brody, Joshua; Turley, Shannon J; Lira, Sergio A; Bronte, Vincenzo; Gordon, Siamon; Heeger, Peter S; Merad, Miriam; Hutchinson, James; Chen, Shu-Hsia; Ochando, Jordi

    2015-06-16

    Tissue effector cells of the monocyte lineage can differentiate into different cell types with specific cell function depending on their environment. The phenotype, developmental requirements, and functional mechanisms of immune protective macrophages that mediate the induction of transplantation tolerance remain elusive. Here, we demonstrate that costimulatory blockade favored accumulation of DC-SIGN-expressing macrophages that inhibited CD8(+) T cell immunity and promoted CD4(+)Foxp3(+) Treg cell expansion in numbers. Mechanistically, that simultaneous DC-SIGN engagement by fucosylated ligands and TLR4 signaling was required for production of immunoregulatory IL-10 associated with prolonged allograft survival. Deletion of DC-SIGN-expressing macrophages in vivo, interfering with their CSF1-dependent development, or preventing the DC-SIGN signaling pathway abrogated tolerance. Together, the results provide new insights into the tolerogenic effects of costimulatory blockade and identify DC-SIGN(+) suppressive macrophages as crucial mediators of immunological tolerance with the concomitant therapeutic implications in the clinic.

  12. A 10 kW dc-dc converter using IGBTs with active snubbers. [Insulated Gate Bipolar Transistor

    NASA Technical Reports Server (NTRS)

    Masserant, Brian J.; Shriver, Jeffrey L.; Stuart, Thomas A.

    1993-01-01

    This full bridge dc-dc converter employs zero voltage switching (ZVS) on one leg and zero current switching (ZCS) on the other. This technique produces exceptionally low IGBT switching losses through the use of an active snubber that recycles energy back to the source. Experimental results are presented for a 10 kW, 20 kHz converter.

  13. User's manual: Computer-aided design programs for inductor-energy-storage dc-to-dc electronic power converters

    NASA Technical Reports Server (NTRS)

    Huffman, S.

    1977-01-01

    Detailed instructions on the use of two computer-aided-design programs for designing the energy storage inductor for single winding and two winding dc to dc converters are provided. Step by step procedures are given to illustrate the formatting of user input data. The procedures are illustrated by eight sample design problems which include the user input and the computer program output.

  14. 78 FR 9044 - Adequacy Status of the Motor Vehicle Emission Budgets for Metropolitan Washington DC Area (DC-MD...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-02-07

    ... AGENCY Adequacy Status of the Motor Vehicle Emission Budgets for Metropolitan Washington DC Area (DC-MD... public that the Motor Vehicle Emissions Budgets (MVEBs) for volatile organic compounds (VOCs) and... 12, 2007 by both the Virginia Department of Environmental Quality (VADEQ) and the District...

  15. Step-by-Step Design of an FPGA-Based Digital Compensator for DC/DC Converters Oriented to an Introductory Course

    ERIC Educational Resources Information Center

    Zumel, P.; Fernandez, C.; Sanz, M.; Lazaro, A.; Barrado, A.

    2011-01-01

    In this paper, a short introductory course to introduce field-programmable gate array (FPGA)-based digital control of dc/dc switching power converters is presented. Digital control based on specific hardware has been at the leading edge of low-medium power dc/dc switching converters in recent years. Besides industry's interest in this topic, from…

  16. 77 FR 55693 - D&C Red No. 6 and D&C Red No. 7; Change in Specification; Confirmation of Effective Date

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-09-11

    ... FR 39921) and that revised the requirements for D&C Red No. 6 and D&C Red No. 7 by replacing the... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration 21 CFR Part 74 D&C Red No. 6 and D&C Red No. 7; Change...

  17. Bicrystal YBCO dc squids with low noise

    SciTech Connect

    Miklich, A.H.; Koelle, D.; Dantsker, E.; Nemeth, D.T.; Kingston, J.J.; Kromann, R.F.; Clarke, J.

    1992-08-01

    We have fabricated 12 dc SQUIDs by laser depositing YBa{sub 2}Cu{sub 3}O{sub 7-x} on a SrTiO{sub 3} bicrystal substrate with a misorientation angle of 24*. At 77K all twelve devices had acceptable values of critical current, resistance and voltage modulation produced by an external magnetic field. The white noise energy of one device with an estimated inductance of 41 pH was 1.8 {times} 10{sup {minus}30} JHz{sup {minus}1}. The noise power scaled as 1/f at frequencies below about 1kHz, however, by using a bias current reversal scheme we were able to reduce this noise by two orders of magnitude at 1 Hz, to a value of about 1.5 {times} 10{sup {minus}29} JHz{sup {minus}1}. We made a magnetometer by coupling the SQUID to a flux transformer with a 5-turn input coil. The measured magnetic field gain was 60, and the white noise 36fT Hz{sup {minus}{1/2}}. However, the transformer produced relatively large levels of 1/f flux noise, not reduced by the bias reversal scheme, that limited the noise at 1 Hz to 1.7 pT Hz{sup {minus}{1/2}}. A single-layer magnetometer with a single-turn pick up loop is briefly described.

  18. Bicrystal YBCO dc squids with low noise

    SciTech Connect

    Miklich, A.H.; Koelle, D.; Dantsker, E.; Nemeth, D.T.; Kingston, J.J.; Kromann, R.F.; Clarke, J.

    1992-08-01

    We have fabricated 12 dc SQUIDs by laser depositing YBa[sub 2]Cu[sub 3]O[sub 7-x] on a SrTiO[sub 3] bicrystal substrate with a misorientation angle of 24*. At 77K all twelve devices had acceptable values of critical current, resistance and voltage modulation produced by an external magnetic field. The white noise energy of one device with an estimated inductance of 41 pH was 1.8 [times] 10[sup [minus]30] JHz[sup [minus]1]. The noise power scaled as 1/f at frequencies below about 1kHz, however, by using a bias current reversal scheme we were able to reduce this noise by two orders of magnitude at 1 Hz, to a value of about 1.5 [times] 10[sup [minus]29] JHz[sup [minus]1]. We made a magnetometer by coupling the SQUID to a flux transformer with a 5-turn input coil. The measured magnetic field gain was 60, and the white noise 36fT Hz[sup [minus][1/2

  19. Analytical derivation of DC SQUID response

    NASA Astrophysics Data System (ADS)

    Soloviev, I. I.; Klenov, N. V.; Schegolev, A. E.; Bakurskiy, S. V.; Kupriyanov, M. Yu

    2016-09-01

    We consider voltage and current response formation in DC superconducting quantum interference device (SQUID) with overdamped Josephson junctions in resistive and superconducting state in the context of a resistively shunted junction (RSJ) model. For simplicity we neglect the junction capacitance and the noise effect. Explicit expressions for the responses in resistive state were obtained for a SQUID which is symmetrical with respect to bias current injection point. Normalized SQUID inductance l=2{{eI}}{{c}}L/{\\hslash } (where I c is the critical current of Josephson junction, L is the SQUID inductance, e is the electron charge and ℏ is the Planck constant) was assumed to be within the range l ≤ 1, subsequently expanded up to l≈ 7 using two fitting parameters. SQUID current response in the superconducting state was considered for arbitrary value of the inductance. The impact of small technological spread of parameters relevant to low-temperature superconductor (LTS) technology was studied, using a generalization of the developed analytical approach, for the case of a small difference of critical currents and shunt resistances of the Josephson junctions, and inequality of SQUID inductive shoulders for both resistive and superconducting states. Comparison with numerical calculation results shows that developed analytical expressions can be used in practical LTS SQUIDs and SQUID-based circuits design, e.g. large serial SQIF, drastically decreasing the time of simulation.

  20. Remote control of a DC discharge experiment

    NASA Astrophysics Data System (ADS)

    Dominguez, Arturo; Zwicker, A.; Wissel, S. A.; Ross, J.

    2013-10-01

    Glow discharges are an excellent tool to introduce plasmas to the general public, in part, because of their visual nature. In this poster, we present recent developments of the Remote DC Discharge Experiment. This experiment consists of a 36'' long × 3.5'' radius glass tube containing air held at pressures of approximately 30-200mTorr with a variable voltage between the ends which can be set between 0-2000V to create a glow discharge. Surrounding the tube, a set of Helmholtz coils can be controlled to demonstrate the effects of axial magnetic fields on the plasma. While the experiment is located at PPPL, a webcam displays the experiment online. The parameters (voltage, magnetic field and pressure) can be controlled remotely in real-time by opening a URL which shows the streaming video, as well as a set of Labview controls. The interface has been designed to attract users with a wide range of academic backgrounds by presenting different levels of interactivity, including the most advanced level which gives the user the possibility of empirically finding the breakdown voltage as a function of pressure and electrode separation.

  1. Spacelab ready for transport to Washington, DC

    NASA Technical Reports Server (NTRS)

    1998-01-01

    Spacelab is wrapped and ready for transport to the National Air and Space Museum in Washington, DC. Spacelab was designed by the European Space Agency (ESA) for the Space Shuttle program and first flew on STS-9 in November 1983. Its final flight was the STS-90 Neurolab mission in April 1998. A sister module will travel home and be placed on display in Europe. The Spacelab concept of modular experiment racks in a pressurized shirt-sleeve environment made it highly user-friendly and accessible. Numerous experiments conceived by hundreds of scientists on the ground were conducted by flight crews in orbit. Spacelab modules served as on-orbit homes for everything from squirrel monkeys to plant seeds. They supported astronomical as well as Earth observations, for servicing the Hubble Space Telescope and for research preparatory to the International Space Station. One of the greatest benefits afforded by the Spacelab missions was the opportunity to fly a mission more than once, with the second or third flight building on the experiences and data gathered from its predecessors.

  2. Antarctic Treaty Summit: Washington, DC (2009)

    NASA Astrophysics Data System (ADS)

    Berkman, P. A.; Young, O. R.

    2005-12-01

    Advancement in Earth system science and international cooperation have been intertwined with the International Polar Years since 1882. In particular, the 3rd International Polar Year (which was convened as the International Geophysical Year from 1 July 1957 through 31 December 1958) specifically demonstrates the role of science in international policy: Acknowledging the substantial contributions to scientific knowledge resulting from international cooperation in scientific investigation in Antarctica; Convinced that the establishment of a firm foundation for the continuation and development of such cooperation on the basis of freedom of scientific investigation in Antarctica as applied during the International Geophysical Year accords with the interests of science and the progress of all mankind; Preamble, 1959 Antarctic Treaty To commemorate the 50th anniversary of the 1959 Antarctic Treaty and to explore the complexities of the science-policy relationship through the lens of a well-constrained case study, an international and interdisciplinary Antarctic Treaty Summit is being planned for 2009 in Washington, DC in conjunction with the International Polar Year 2007-08 (http://www.ipy.org).

  3. Counterrotating brushless dc permanent magnet motor

    SciTech Connect

    Hawsey, R.A.; Bailey, J.M.

    1990-01-01

    An brushless DC permanent magnet motor is provided for driving an autonomous underwater vehicle. In one embodiment, the motor comprises four substantially flat stators disposed in stacked relationship, with pairs of the stators being axially spaced and each of the stators comprising a tape-wound stator coil; and a first and second substantially flat rotors disposed between the spaced pairs of stators. Each of the rotors includes an annular array of permanent magnets embedded therein. A first shaft is connected to the first rotor and a second, concentric shaft is connected to the second rotor, and drive unit causes rotation of the two shafts in opposite directions. The second shaft comprises a hollow tube having a central bore therein in which the first shaft is disposed. Two different sets of bearings support the first and second shAfts. In another embodiment, the motor comprises two ironless stators and pairs and rotors mounted no opposite sides of the stators and driven by counterrotating shafts.

  4. DC-magnetic field vector measurement

    NASA Technical Reports Server (NTRS)

    Schmidt, R.

    1981-01-01

    A magnetometer experiment was designed to determine the local magnetic field by measuring the total of the Earth's magnetic field and that of an unknown spacecraft. The measured field vector components are available to all onboard experiments via the Spacelab command and data management system. The experiment consists of two parts, an electronic box and the magnetic field sensor. The sensor includes three independent measuring flux-gate magnetometers, each measuring one component. The physical background is the nonlinearity of the B-H curve of a ferrite material. Two coils wound around a ferrite rod are necessary. One of them, a tank coil, pumps the ferrite rod at approximately 20 kilohertz. As a consequence of the nonlinearity, many harmonics can be produced. The second coil (i.e., the detection coil) resonates to the first harmonic. If an unknown dc or low-frequency magnetic field exists, the amplitude of the first harmonic is a measure for the unknown magnetic field. The voltages detected by the sensors are to be digitized and transferred to the command and data management system.

  5. Motor control for a brushless DC motor

    NASA Technical Reports Server (NTRS)

    Peterson, William J. (Inventor); Faulkner, Dennis T. (Inventor)

    1985-01-01

    This invention relates to a motor control system for a brushless DC motor having an inverter responsively coupled to the motor control system and in power transmitting relationship to the motor. The motor control system includes a motor rotor speed detecting unit that provides a pulsed waveform signal proportional to rotor speed. This pulsed waveform signal is delivered to the inverter to thereby cause an inverter fundamental current waveform output to the motor to be switched at a rate proportional to said rotor speed. In addition, the fundamental current waveform is also pulse width modulated at a rate proportional to the rotor speed. A fundamental current waveform phase advance circuit is controllingly coupled to the inverter. The phase advance circuit is coupled to receive the pulsed waveform signal from the motor rotor speed detecting unit and phase advance the pulsed waveform signal as a predetermined function of motor speed to thereby cause the fundamental current waveform to be advanced and thereby compensate for fundamental current waveform lag due to motor winding reactance which allows the motor to operate at higher speeds than the motor is rated while providing optimal torque and therefore increased efficiency.

  6. DC66814 AERIAL VIEW OF THE CAPITOL REFLECTING POOL, LOOKING NORTHEAST ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    DC-668-14 AERIAL VIEW OF THE CAPITOL REFLECTING POOL, LOOKING NORTHEAST UP LOUISIANA AVENUE TOWARD UNION STATION FROM ABOVE THE MALL - L'Enfant-McMillan Plan of Washington, DC, Washington, District of Columbia, DC

  7. DC66820 VISTA EAST ALONG M STREET TO THOMAS CIRCLE FROM ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    DC-668-20 VISTA EAST ALONG M STREET TO THOMAS CIRCLE FROM RESERVATION NO. 14 0 AT NEW HAMPSHIRE AVENUE AND 21ST STREET, NW - L'Enfant-McMillan Plan of Washington, DC, Washington, District of Columbia, DC

  8. DC66842 VIEW WEST FROM BANNEKER CIRCLE (RESERVATION NO. 719) TO ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    DC-668-42 VIEW WEST FROM BANNEKER CIRCLE (RESERVATION NO. 719) TO THE DOME OF THE JEFFERSON MEMORIAL IN WEST POTOMAC PARK - L'Enfant-McMillan Plan of Washington, DC, Washington, District of Columbia, DC

  9. DC66840 VIEW EAST ON THE SOUTHEAST/SOUTHWEST FREEWAY (IN THE HISTORIC ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    DC-668-40 VIEW EAST ON THE SOUTHEAST/SOUTHWEST FREEWAY (IN THE HISTORIC F STREET CORRIDOR) FROM THE TENTH STREET PROMENADE, SW - L'Enfant-McMillan Plan of Washington, DC, Washington, District of Columbia, DC

  10. DC6684 AERIAL VIEW LOOKING SLIGHTLY SOUTHEAST DOWN THE NORTH CAPITOL ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    DC-668-4 AERIAL VIEW LOOKING SLIGHTLY SOUTHEAST DOWN THE NORTH CAPITOL STREET CORRIDOR FROM ABOVE THE RHODE ISLAND AVENUE VICINITY - L'Enfant-McMillan Plan of Washington, DC, Washington, District of Columbia, DC

  11. DC66843 VIEW OF THE INDEPENDENCE AVENUE CORRIDOR SPANNED BY THE ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    DC-668-43 VIEW OF THE INDEPENDENCE AVENUE CORRIDOR SPANNED BY THE •DEPARTMENT OF AGRICULTURE BRIDGES, LOOKING WEST FROM TWELFTH STREET, SW - L'Enfant-McMillan Plan of Washington, DC, Washington, District of Columbia, DC

  12. DC66813 AERIAL VIEW OF THE NORTHWEST QUADRANT, LOOKING NORTH UP ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    DC-668-13 AERIAL VIEW OF THE NORTHWEST QUADRANT, LOOKING NORTH UP THE 2 3RD STREET CORRIDOR FROM ABOVE WEST POTOMAC PARK - L'Enfant-McMillan Plan of Washington, DC, Washington, District of Columbia, DC

  13. DC65819 VIEW NORTHWEST ALONG THE POTOMAC RIVERFRONT AND INTO GEORGETOWN ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    DC-658-19 VIEW NORTHWEST ALONG THE POTOMAC RIVERFRONT AND INTO GEORGETOWN FROM THE ROOF OF THE JOHN F. KENNEDY CENTER FOR THE PERFORMING ARTS - L'Enfant-McMillan Plan of Washington, DC, Washington, District of Columbia, DC

  14. Characteristics of DC electric fields in transient plasma sheet events

    NASA Astrophysics Data System (ADS)

    Laakso, H. E.; Escoubet, C. P.; Masson, A.

    2015-12-01

    We take an advantage of five different DC electric field measurements in the plasma sheet available from the EFW double probe experiment, EDI electron drift instrument, CODIF and HIA ion spectrometers, and PEACE electron spectrometer on the four Cluster spacecraft. The calibrated observations of the three spectrometers are used to determine the proton and electron velocity moments. The velocity moments can be used to estimate the proton and electron drift velocity and furthermore the DC electric field, assuming that the electron and proton velocity perpendicular to the magnetic field is dominated by the ExB drift motion. Naturally when ions and electrons do not perform a proper drift motion, which can happen in the plasma sheet, the estimated DC electric field from ion and electron motion is not correct. However, surprisingly often the DC electric fields estimated from electron and ion motions are identical suggesting that this field is a real DC electric field around the measurement point. As the measurement techniques are so different, it is quite plausible that when two different measurements yield the same DC electric field, it is the correct field. All five measurements of the DC electric field are usually not simultaneously available, especially on Cluster 2 where CODIF and HIA are not operational, or on Cluster 4 where EDI is off. In this presentation we investigate DC electric field in various transient plasma sheet events such as dipolarization events and BBF's and how the five measurements agree or disagree. There are plenty of important issues that are considered, e.g., (1) what kind of DC electric fields exist in such events and what are their spatial scales, (2) do electrons and ions perform ExB drift motions in these events, and (3) how well the instruments have been calibrated.

  15. Killing of naive T cells by CD95L-transfected dendritic cells (DC): in vivo study using killer DC-DC hybrids and CD4(+) T cells from DO11.10 mice.

    PubMed

    Kusuhara, Masahiro; Matsue, Keiko; Edelbaum, Dale; Loftus, Julie; Takashima, Akira; Matsue, Hiroyuki

    2002-04-01

    Dendritic cells (DC) play the dual task of initiating cellular immunity against potentially harmful foreign antigens (Ag), while maintaining immunological tolerance to self-Ag and environmental Ag. As an approach to induce Ag-specific suppression, we and others introduced CD95 ligand (L) cDNA into DC. The resulting "killer" DC delivered apoptotic signals, instead of activation signals, to primed CD4(+) T cells in vitro and induced Ag-specific immunosuppression in vivo. To study the impact of killer DC on naive T cells, the fate of Ag-reactive T cells and the extent of their depletion after killer DC treatment, we performed in vitro and in vivo reconstitution experiments using: (a) killer DC-DC hybrids created between CD95L-transduced XS106 DC clone (A/J origin) and splenic DC from BALB/c mice, (b) CD4(+) T cells isolated from DO11.10 transgenic mice (BALB/c background), and (c) OVA(323-339) peptide as relevant Ag. Ovalbumin (OVA)-pulsed killer DC-DC hybrids inhibited DO11.10 T cell activation triggered by conventional DC, instead of inducing their activation. Rapid apoptosis of T cells was observed after co-culture with OVA-pulsed killer DC-DC hybrids, but not with non-pulsed killer DC-DC hybrids or OVA-pulsed control DC-DC hybrids. For in vivo reconstitution, (BALB/cxA/J)F1 mice received subcutaneous administration of killer DC-DC hybrids, followed by intravenous inoculation of DO11.10 T cells. Killer DC-DC hybrids migrated preferentially to draining lymph nodes albeit with relatively low efficiency (0.5-1% recovery) and they induced significant, but incomplete (30-40%) killing of DO11.10 T cells in this location. These results document the abilities of CD95L-transduced DC to trigger apoptosis of naive T cells in an Ag-specific manner, to overrule T cell activation signals delivered by conventional DC, and to reduce local frequencies of Ag-reactive T cells in vivo. Our data also uncover two major limitations (relatively low homing efficiency and incomplete

  16. High reliability DC/DC converter module for electronic boards equipped with FPGAs

    NASA Astrophysics Data System (ADS)

    Viganò, W.; Boccardi, A.; Zamantzas, C.

    2015-01-01

    The Beam Instrumentation Group at CERN is designing a new general-purpose VME carrier module utilising several PTH04T230W DC/DC converters. These off-the-shelf converters are built with unshielded inductors and need to be mounted on the printed circuit board as stand-alone components. Thus, reducing the global manageability and increasing the total cost of the carrier module. The new design aims to develop a module with better power dissipation, efficiency and reliability. In the future, it should be also possible to be directly integrated on the mainboard. For this reason, a Buck DC/DC converter has been implemented with the following main characteristics: input range from 3.0 V to 5.5 V; output range from 0.6 V to 3.3 V, settable by means of an external resistor; output current protection at 6 A; maximum output ripple ± 50 mVpp; switching frequency of 300KHz; short circuit protection; On/Off function; EMI reduction with frequency spread spectrum; soft-start function and thermal shutdown, in a 16 × 19 mm compact size. The selected buck controller is the TPS40303 integrated circuit and drives the CSD16321 power MOSFET, both from Texas Instruments. All selected components have been used at a minimum derating of 50% to reduce component stress and increase the reliability of this module. The selected inductors, i.e. Bourns SRP1055, are the main contributor for the high efficiency (95%), due to their very low equivalent series resistance. On the 4-layer PCB comprising all the components of this module, a snubber circuit, for further reduction of the output ripple due to the MOSFET ringing, can be mounted optionally. It is left as an option due to its effect on the total efficiency. The board layout has been optimized for maximum heat transfer and it can be used without active cooling. The board can maintain the maximum temperature on its surface, while at maximum current output, below 55°C at 25°C ambient temperature. An example of the electrical performance

  17. Implementing the DC Mode in Cosmological Simulations with Supercomoving Variables

    NASA Astrophysics Data System (ADS)

    Gnedin, Nickolay Y.; Kravtsov, Andrey V.; Rudd, Douglas H.

    2011-06-01

    As emphasized by previous studies, proper treatment of the density fluctuation on the fundamental scale of a cosmological simulation volume—the "DC mode"—is critical for accurate modeling of spatial correlations on scales >~ 10% of simulation box size. We provide further illustration of the effects of the DC mode on the abundance of halos in small boxes and show that it is straightforward to incorporate this mode in cosmological codes that use the "supercomoving" variables. The equations governing evolution of dark matter and baryons recast with these variables are particularly simple and include the expansion factor, and hence the effect of the DC mode, explicitly only in the Poisson equation.

  18. DC information preservation for cardiopulmonary monitor utilizing CW Doppler radar.

    PubMed

    Vergara, Alexander M; Boric-Lubecke, Olga; Lubecke, Victor M

    2008-01-01

    Direct conversion RF receivers introduce large DC offsets, reducing the dynamic range of the baseband signal. Coupled with the relatively small time varying signals in human vital sign monitoring using CW Doppler radar, extraction of cardio-pulmonary information becomes difficult. Previous DC offset compensation techniques utilizing AC coupling have proven detrimental to the performance of the system and the integrity of the low-frequency cardiopulmonary signals. A proposed system utilizing digitally controlled voltage feedback and center finding preserves the important DC information for optimal extraction of phase information in the quadrature system.

  19. Implementing the DC Mode in Cosmological Simulations with Supercomoving Variables

    SciTech Connect

    Gnedin, Nickolay Y; Kravtsov, Andrey V; Rudd, Douglas H

    2011-06-02

    As emphasized by previous studies, proper treatment of the density fluctuation on the fundamental scale of a cosmological simulation volume - the 'DC mode' - is critical for accurate modeling of spatial correlations on scales ~> 10% of simulation box size. We provide further illustration of the effects of the DC mode on the abundance of halos in small boxes and show that it is straightforward to incorporate this mode in cosmological codes that use the 'supercomoving' variables. The equations governing evolution of dark matter and baryons recast with these variables are particularly simple and include the expansion factor, and hence the effect of the DC mode, explicitly only in the Poisson equation.

  20. Tachometers Derived From a Brushless DC Motor

    NASA Technical Reports Server (NTRS)

    Howard, David E.; Smith, Dennis A.

    2007-01-01

    The upper part of the figure illustrates the major functional blocks of a direction-sensitive analog tachometer circuit based on the use of an unexcited two-phase brushless dc motor as a rotation transducer. The primary advantages of this circuit over many older tachometer circuits include the following: Its output inherently varies linearly with the rate of rotation of the shaft. Unlike some tachometer circuits that rely on differentiation of voltages with respect to time, this circuit relies on integration, which results in signals that are less noisy. There is no need for an additional shaft-angle sensor, nor is there any need to supply electrical excitation to a shaft-angle sensor. There is no need for mechanical brushes (which tend to act as sources of electrical noise). The underlying concept and electrical design are relatively simple. This circuit processes the back-electromagnetic force (back-emf) outputs of the two motor phases into a voltage directly proportional to the instantaneous rate (sign magnitude) of rotation of the shaft. The processing in this circuit effects a straightforward combination of mathematical operations leading to a final operation based on the well-known trigonometric identity (sin x)2 + (cos x)2 = 1 for any value of x. The principle of operation of this circuit is closely related to that of the tachometer circuit described in Tachometer Derived From Brushless Shaft-Angle Resolver (MFS-28845), NASA Tech Briefs, Vol. 19, No. 3 (March 1995), page 39. However, the present circuit is simpler in some respects because there is no need for sinusoidal excitation of shaftangle- resolver windings.

  1. Natural gas pipeline leaks across Washington, DC.

    PubMed

    Jackson, Robert B; Down, Adrian; Phillips, Nathan G; Ackley, Robert C; Cook, Charles W; Plata, Desiree L; Zhao, Kaiguang

    2014-01-01

    Pipeline safety in the United States has increased in recent decades, but incidents involving natural gas pipelines still cause an average of 17 fatalities and $133 M in property damage annually. Natural gas leaks are also the largest anthropogenic source of the greenhouse gas methane (CH4) in the U.S. To reduce pipeline leakage and increase consumer safety, we deployed a Picarro G2301 Cavity Ring-Down Spectrometer in a car, mapping 5893 natural gas leaks (2.5 to 88.6 ppm CH4) across 1500 road miles of Washington, DC. The δ(13)C-isotopic signatures of the methane (-38.2‰ ± 3.9‰ s.d.) and ethane (-36.5 ± 1.1 s.d.) and the CH4:C2H6 ratios (25.5 ± 8.9 s.d.) closely matched the pipeline gas (-39.0‰ and -36.2‰ for methane and ethane; 19.0 for CH4/C2H6). Emissions from four street leaks ranged from 9200 to 38,200 L CH4 day(-1) each, comparable to natural gas used by 1.7 to 7.0 homes, respectively. At 19 tested locations, 12 potentially explosive (Grade 1) methane concentrations of 50,000 to 500,000 ppm were detected in manholes. Financial incentives and targeted programs among companies, public utility commissions, and scientists to reduce leaks and replace old cast-iron pipes will improve consumer safety and air quality, save money, and lower greenhouse gas emissions.

  2. High power density dc-to-dc converters for aerospace applications

    NASA Technical Reports Server (NTRS)

    Divan, Deepakraj M.

    1990-01-01

    Three dc-to-dc converter topologies aimed at high-power high-frequency applications are introduced. Major system parasitics, namely, the leakage inductance of the transformer and the device output capacitance are efficiently utilized. Of the three circuits, the single-phase and three-phase versions of the dual active bridge topology demonstrate minimal stresses, better utilization of the transformer, bidirectional, and buck-boost modes of operation. All circuits operate at a constant switching frequency, thus simplifying design of the reactive elements. The power transfer characteristics and soft-switching regions on the Vout-Iout plane are identified. Two coaxial transformers with different cross-sections were built for a rating of 50 kVA. Based on the single-phase dual active bridge topology, a 50 kW, 50 kHz converter operating at an input voltage of 200 Vdc and an output voltage of 1600 Vdc was fabricated. Characteristics of current-fed output make the dual active bridge topologies amenable to paralleling and hence extension to megawatt power levels. Projections to a 1 MW system operating from a 500 Vdc input, at an output voltage of 10 kVdc and a switching frequency of 50 kHz, using MOS-controlled thyristors, coaxially wound transformers operating at three times the present current density with cooling, and multilayer ceramic capacitors, suggests an overall power density of 0.075 to 0.08 kg/kW and an overall efficiency of 96 percent.

  3. Electrodeposited Nanolaminated CoNiFe Cores for Ultracompact DC-DC Power Conversion

    SciTech Connect

    Kim, J; Kim, M; Herrault, F; Park, JY; Allen, MG

    2015-09-01

    Laminated metallic alloy cores (i.e., alternating layers of thin film metallic alloy and insulating material) of appropriate lamination thickness enable suppression of eddy current losses at high frequencies. Magnetic cores comprised of many such laminations yield substantial overall magnetic volume, thereby enabling high-power operation. Previously, we reported nanolaminated permalloy (Ni-80 Fe-20) cores based on a sequential electrodeposition technique, demonstrating negligible eddy current losses at peak flux densities up to 0.5 T and operating at megahertz frequencies. This paper demonstrates improved performance of nanolaminated cores comprising tens to hundreds of layers of 300-500-nm-thick CoNiFe films that exhibit superior magnetic properties (e.g., higher saturation flux density and lower coercivity) than permalloy. Nanolaminated CoNiFe cores can be operated up to a peak flux density of 0.9 T, demonstrating improved power handling capacity and exhibiting 30% reduced volumetric core loss, attributed to lowered hysteresis losses compared to the nanolaminated permalloy core of the same geometry. Operating these cores in a buck dc-dc power converter at a switching frequency of 1 MHz, the nanolaminated CoNiFe cores achieved a conversion efficiency exceeding 90% at output power levels up to 7 W, compared to an achieved permalloy core conversion efficiency below 86% at 6 W.

  4. A Low-Power Asynchronous Step-Down DC-DC Converter for Implantable Devices.

    PubMed

    Al-Terkawi Hasib, Omar; Sawan, M; Savaria, Y

    2011-06-01

    In this paper, we present a fully integrated asynchronous step-down switched capacitor dc-dc conversion structure suitable for supporting ultra-low-power circuits commonly found in biomedical implants. The proposed converter uses a fully digital asynchronous state machine as the heart of the control circuitry to generate the drive signals. To minimize the switching losses, the asynchronous controller scales the switching frequency of the drive signals according to the loading conditions. It also turns on additional parallel switches when needed and has a backup synchronous drive mode. This circuit regulates load voltages from 300 mV to 1.1 V derived from a 1.2-V input voltage. A total of 350 pF on-chip capacitance was implemented to support a maximum of 230-μ W load power, while providing efficiency up to 80%. The circuit validating the proposed concepts was fabricated in 0.13- μm complementary metal-oxide semiconductor technology. Experimental test results confirm the expected functionality and performance of the proposed circuit. PMID:23851480

  5. An Optimal Current Observer for Predictive Current Controlled Buck DC-DC Converters

    PubMed Central

    Min, Run; Chen, Chen; Zhang, Xiaodong; Zou, Xuecheng; Tong, Qiaoling; Zhang, Qiao

    2014-01-01

    In digital current mode controlled DC-DC converters, conventional current sensors might not provide isolation at a minimized price, power loss and size. Therefore, a current observer which can be realized based on the digital circuit itself, is a possible substitute. However, the observed current may diverge due to the parasitic resistors and the forward conduction voltage of the diode. Moreover, the divergence of the observed current will cause steady state errors in the output voltage. In this paper, an optimal current observer is proposed. It achieves the highest observation accuracy by compensating for all the known parasitic parameters. By employing the optimal current observer-based predictive current controller, a buck converter is implemented. The converter has a convergently and accurately observed inductor current, and shows preferable transient response than the conventional voltage mode controlled converter. Besides, costs, power loss and size are minimized since the strategy requires no additional hardware for current sensing. The effectiveness of the proposed optimal current observer is demonstrated experimentally. PMID:24854061

  6. An optimal current observer for predictive current controlled buck DC-DC converters.

    PubMed

    Min, Run; Chen, Chen; Zhang, Xiaodong; Zou, Xuecheng; Tong, Qiaoling; Zhang, Qiao

    2014-01-01

    In digital current mode controlled DC-DC converters, conventional current sensors might not provide isolation at a minimized price, power loss and size. Therefore, a current observer which can be realized based on the digital circuit itself, is a possible substitute. However, the observed current may diverge due to the parasitic resistors and the forward conduction voltage of the diode. Moreover, the divergence of the observed current will cause steady state errors in the output voltage. In this paper, an optimal current observer is proposed. It achieves the highest observation accuracy by compensating for all the known parasitic parameters. By employing the optimal current observer-based predictive current controller, a buck converter is implemented. The converter has a convergently and accurately observed inductor current, and shows preferable transient response than the conventional voltage mode controlled converter. Besides, costs, power loss and size are minimized since the strategy requires no additional hardware for current sensing. The effectiveness of the proposed optimal current observer is demonstrated experimentally.

  7. Lightweight DC-DC Converter with Partial Power Processing and MPPT for a Solar Powered Aircraft

    NASA Astrophysics Data System (ADS)

    Diab-Marzouk, Ahmad

    A lightweight dc-dc partial power processing converter is demonstrated for solar aerospace applications. A system-level model is conceived to determine conformity to payload and target distance objectives, with the Solarship aircraft used as an application example. The concept of partial power processing is utilized to realize a high efficiency lightweight converter that performs Max Peak Power Tracking (MPPT) to transfer power from the aircraft solar array to the high-voltage battery bus. The isolated Cuk is determined to be a suitable converter topology for the application. A small-signal model is derived for control design. The operation of a 400V, 2.7 kW prototype is verified at high frequency (200 kHz), high efficiency (> 98%), small mass (0.604 kg), and uses no electrolytic capacitors. MPPT operation is verified on a 376 V commercial solar installation at The University of Toronto. The prototype serves as an enabling technology for solar aerospace applications.

  8. A Low-Power Asynchronous Step-Down DC-DC Converter for Implantable Devices.

    PubMed

    Al-Terkawi Hasib, Omar; Sawan, M; Savaria, Y

    2011-06-01

    In this paper, we present a fully integrated asynchronous step-down switched capacitor dc-dc conversion structure suitable for supporting ultra-low-power circuits commonly found in biomedical implants. The proposed converter uses a fully digital asynchronous state machine as the heart of the control circuitry to generate the drive signals. To minimize the switching losses, the asynchronous controller scales the switching frequency of the drive signals according to the loading conditions. It also turns on additional parallel switches when needed and has a backup synchronous drive mode. This circuit regulates load voltages from 300 mV to 1.1 V derived from a 1.2-V input voltage. A total of 350 pF on-chip capacitance was implemented to support a maximum of 230-μ W load power, while providing efficiency up to 80%. The circuit validating the proposed concepts was fabricated in 0.13- μm complementary metal-oxide semiconductor technology. Experimental test results confirm the expected functionality and performance of the proposed circuit.

  9. Bifurcation boundary conditions for current programmed PWM DC-DC converters at light loading

    NASA Astrophysics Data System (ADS)

    Fang, Chung-Chieh

    2012-10-01

    Three types of bifurcations (instabilities) in the PWM DC-DC converter at light loading under current mode control in continuous-conduction mode (CCM) or discontinuous-conduction mode (DCM) are analysed: saddle-node bifurcation (SNB) in CCM or DCM, border-collision bifurcation during the CCM-DCM transition, and period-doubling bifurcation in CCM. Different bifurcations occur in some particular loading ranges. Bifurcation boundary conditions separating stable regions from unstable regions in the parametric space are derived. A new methodology to analyse the SNB in the buck converter based on the peak inductor current is proposed. The same methodology is applied to analyse the other types of bifurcations and converters. In the buck converter, multiple stable/unstable CCM/DCM steady-state solutions may coexist. Possibility of multiple solutions deserves careful study, because an ignored solution may merge with a desired stable solution and make both disappear. Understanding of SNB can explain some sudden disappearances or jumps of steady-state solutions observed in switching converters.

  10. Design and implementation of a switched capacitor-based embedded hybrid DC-DC converter

    NASA Astrophysics Data System (ADS)

    Bhattacharyya, Kaushik; Mandal, Pradip

    2012-06-01

    Here, we propose an integrated hybrid DC-DC converter suitable for high drop-out energy conscious applications. In the hybrid converter topology, along with a linear regulator two switched capacitors are used to store and recycle charge for better power efficiency. Without significant power loss the switched capacitors step down the supply voltage for the linear regulator working in low drop-out mode. The linear regulator, on the other hand, attenuates the voltage ripple that originates from the switched capacitors converter on its power supply rejection ratio. It also helps for line and load regulation. Additionally, a synthesised counter ripple is injected through the linear regulator to further reduce the output ripple. With these two techniques, for a moderate load current and an acceptable output ripple, the switching and load capacitors are reduced to a value which can be implemented within the chip. The proposed integrated converter circuit has been designed, implemented and tested in a 0.18 mm CMOS process for 3.3-1.3V conversion. With two switching capacitors of 210 pF each and 100 pF load capacitor, more than 13 mA of load current, measured peak-to-peak output voltage ripple is 146 mV. The achieved measured power efficiency is 64.97%. Exhaustive silicon characterisation of the converter is done to observe the power efficiency and ripple variation at different frequency of operations.

  11. Fast response double series resonant high-voltage DC-DC converter

    NASA Astrophysics Data System (ADS)

    Lee, S. S.; Iqbal, S.; Kamarol, M.

    2012-10-01

    In this paper, a novel double series resonant high-voltage dc-dc converter with dual-mode pulse frequency modulation (PFM) control scheme is proposed. The proposed topology consists of two series resonant tanks and hence two resonant currents flow in each switching period. Moreover, it consists of two high-voltage transformer with the leakage inductances are absorbed as resonant inductor in the series resonant tanks. The secondary output of both transformers are rectified and mixed before supplying to load. In the resonant mode operation, the series resonant tanks are energized alternately by controlling two Insulated Gate Bipolar Transistor (IGBT) switches with pulse frequency modulation (PFM). This topology operates in discontinuous conduction mode (DCM) with all IGBT switches operating in zero current switching (ZCS) condition and hence no switching loss occurs. To achieve fast rise in output voltage, a dual-mode PFM control during start-up of the converter is proposed. In this operation, the inverter is started at a high switching frequency and as the output voltage reaches 90% of the target value, the switching frequency is reduced to a value which corresponds to the target output voltage. This can effectively reduce the rise time of the output voltage and prevent overshoot. Experimental results collected from a 100-W laboratory prototype are presented to verify the effectiveness of the proposed system.

  12. High efficiency and low electromagnetic interference boost DC-DC converter

    NASA Astrophysics Data System (ADS)

    Yajun, Li; Xinquan, Lai; Qiang, Ye; Bing, Yuan

    2014-04-01

    A synchronous boost DC-DC converter with an adaptive dead time control (DTC) circuit and anti-ringing circuit is presented. The DTC circuit is used to provide adjustable dead time and zero inductor current detection for power transistors and therefore, a high efficiency is achieved by minimizing power losses, such as the shoot-through current loss, the body diode conduction loss, the charge-sharing loss and the reverse inductor current loss. Simultaneously, a novel anti-ringing circuit controlled by the switching sequence of power transistors is developed to suppress the ringing when the converter enters the discontinuous conduction mode (DCM) for low electromagnetic interference (EMI) and additional power savings. The proposed converter has been fabricated in a 0.6 μm CDMOS technology. Simulation and experimental results show that the power efficiency of the boost converter is above 81% under different load currents from 10 to 250 mA and a peak efficiency of 90% is achieved at about 100 mA. Moreover, the ringing is easily suppressed by the anti-ringing circuit and therefore the EMI noise is attenuated.

  13. Design of Energy Storage Reactors for Dc-To-Dc Converters. Ph.D. Thesis

    NASA Technical Reports Server (NTRS)

    Chen, D. Y.

    1975-01-01

    Two methodical approaches to the design of energy-storage reactors for a group of widely used dc-to-dc converters are presented. One of these approaches is based on a steady-state time-domain analysis of piecewise-linearized circuit models of the converters, while the other approach is based on an analysis of the same circuit models, but from an energy point of view. The design procedure developed from the first approach includes a search through a stored data file of magnetic core characteristics and results in a list of usable reactor designs which meet a particular converter's requirements. Because of the complexity of this procedure, a digital computer usually is used to implement the design algorithm. The second approach, based on a study of the storage and transfer of energy in the magnetic reactors, leads to a straightforward design procedure which can be implemented with hand calculations. An equation to determine the lower-bound volume of workable cores for given converter design specifications is derived. Using this computer lower-bound volume, a comparative evaluation of various converter configurations is presented.

  14. Adaptive terminal sliding-mode control strategy for DC-DC buck converters.

    PubMed

    Komurcugil, Hasan

    2012-11-01

    This paper presents an adaptive terminal sliding mode control (ATSMC) strategy for DC-DC buck converters. The idea behind this strategy is to use the terminal sliding mode control (TSMC) approach to assure finite time convergence of the output voltage error to the equilibrium point and integrate an adaptive law to the TSMC strategy so as to achieve a dynamic sliding line during the load variations. In addition, the influence of the controller parameters on the performance of closed-loop system is investigated. It is observed that the start up response of the output voltage becomes faster with increasing value of the fractional power used in the sliding function. On the other hand, the transient response of the output voltage, caused by the step change in the load, becomes faster with decreasing the value of the fractional power. Therefore, the value of fractional power is to be chosen to make a compromise between start up and transient responses of the converter. Performance of the proposed ATSMC strategy has been tested through computer simulations and experiments. The simulation results of the proposed ATSMC strategy are compared with the conventional SMC and TSMC strategies. It is shown that the ATSMC exhibits a considerable improvement in terms of a faster output voltage response during load changes.

  15. Experimental observation of further frequency upshift from dc to ac radiation converter with perpendicular dc magnetic field

    PubMed

    Higashiguchi; Yugami; Gao; Niiyama; Sasaki; Takahashi; Ito; Nishida

    2000-11-20

    A frequency upshift of a short microwave pulse is generated by the interaction between a relativistic underdense ionization front and a periodic electrostatic field with a perpendicular dc magnetic field. When the dc magnetic field is applied, further frequency upshift of 3 GHz is observed with respect to an unmagnetized case which has typically a GHz range. The radiation frequency depends on both the plasma density and the strength of the dc magnetic field, i.e., the plasma frequency and the cyclotron frequency. The frequency of the emitted radiation is in reasonable agreement with the theoretical values. PMID:11082591

  16. Description and Status of the DC Lightning Mapping Array

    NASA Technical Reports Server (NTRS)

    Blakeslee, Richard; Rudlosky, Scott D.; Bailey, Jeffrey C.; Hall, John M.; Goodman, Steven J.; Zubrick, Steven; Krehbiel, Paul

    2011-01-01

    The DC Lightning Mapping Array (DC LMA) centered on the Washington, DC metro region has been in operation since 2006. During that time the DC LMA has provided real time data to regional National Weather Service (NSF) Sterling, VA forecast office for operations support and the NOAA Meteorological Development Laboratory (MDL) for new product development and assessment. Data from this network (as well as other from other LMA systems) are now being used to create proxy Geostationary Lightning Mapper (GLM) data sets for GOES-R risk reduction and algorithm development activities. In addition, since spring 2009 data are provided to the Storm Prediction Center in support of Hazardous Weather Testbed and GOES-R Proving Ground activities during the Spring Program. Description, status and plans will be discussed.

  17. Analysis of DC offset Influence on Transient Signal

    NASA Astrophysics Data System (ADS)

    Wang, Y.; Lin, J.; Zhou, G. H.

    2006-10-01

    Based on the characteristic of transient signal and the principle of floating-point data acquisition circuit, the influences of DC offset on transient signal are analyzed. And the conclusion can be obtained that the singularity and saturation distortions in transient signals can be produced by DC offset through the detailed principle analysis, the limits calculation of DC offset, and waveform simulation while the DC offset is present in floating-point amplifier circuit of floating-point data acquisition circuit. At the same time, the distributions of distortions in those conditions that the single and several theoretic transient signals and also in actual measured transient signal are compared and discussed. Finally, the corresponding solutions are given according to the main factors which produce the waveform distortion. In a word, this research can provide useful references for the adjustment of floating-point receiver and the analysis of waveform distortion.

  18. Enhancement of Current Density by dc Electric Concentrator

    PubMed Central

    Jiang, Wei Xiang; Luo, Chen Yang; Ma, Hui Feng; Mei, Zhong Lei; Cui, Tie Jun

    2012-01-01

    We investigate a dc electric concentrator for steady current fields theoretically and experimentally. Based on the transformation electrostatics, we show that the dc concentrator can focus electric currents into the central concentrated region and enhance the electric field and current density. Outside the concentrator, the current lines are distributed as the same as those in a homogeneous conducting material. Hence, such a dc electric concentrator has no impact on other external devices. Using the analogy between electrically conducting materials and resistor networks, we design, fabricate, and test a dc concentrator using the circuit theory. The measured results agree very well with the theoretical predictions and numerical simulations, demonstrating the perfect concentrating performance. PMID:23233875

  19. TRIANGLE-SHAPED DC CORONA DISCHARGE DEVICE FOR MOLECULAR DECOMPOSITION

    EPA Science Inventory

    The paper discusses the evaluation of electrostatic DC corona discharge devices for the application of molecular decomposition. A point-to-plane geometry corona device with a rectangular cross section demonstrated low decomposition efficiencies in earlier experimental work. The n...

  20. DC motor proportional control system for orthotic devices

    NASA Technical Reports Server (NTRS)

    Blaise, H. T.; Allen, J. R.

    1972-01-01

    Multi-channel proportional control system for operation of dc motors for use with externally-powered orthotic arm braces is described. Components of circuitry and principles of operation are described. Schematic diagram of control circuit is provided.

  1. Rotor position sensor switches currents in brushless dc motors

    NASA Technical Reports Server (NTRS)

    1965-01-01

    Reluctance switch incorporated in an induction motor is used for sensing rotor position and switching armature circuits in a brushless dc motor. This device drives the solar array system of an unmanned space satellite.

  2. Radiofrequency amplifier based on a dc superconducting quantum interference device

    DOEpatents

    Hilbert, Claude; Martinis, John M.; Clarke, John

    1986-01-01

    A low noise radiofrequency amplifier (10), using a dc SQUID (superconducting quantum interference device) as the input amplifying element. The dc SQUID (11) and an input coil (12) are maintained at superconductivity temperatures in a superconducting shield (13), with the input coil (12) inductively coupled to the superconducting ring (17) of the dc SQUID (11). A radiofrequency signal from outside the shield (13) is applied to the input coil (12), and an amplified radiofrequency signal is developed across the dc SQUID ring (17) and transmitted to exteriorly of the shield (13). A power gain of 19.5.+-.0.5 dB has been achieved with a noise temperature of 1.0.+-.0.4 K. at a frequency of 100 MHz.

  3. Radiofrequency amplifier based on a dc superconducting quantum interference device

    DOEpatents

    Hilbert, C.; Martinis, J.M.; Clarke, J.

    1984-04-27

    A low noise radiofrequency amplifer, using a dc SQUID (superconducting quantum interference device) as the input amplifying element. The dc SQUID and an input coil are maintained at superconductivity temperatures in a superconducting shield, with the input coil inductively coupled to the superconducting ring of the dc SQUID. A radiofrequency signal from outside the shield is applied to the input coil, and an amplified radiofrequency signal is developed across the dc SQUID ring and transmitted to exteriorly of the shield. A power gain of 19.5 +- 0.5 dB has been achieved with a noise temperature of 1.0 +- 0.4 K at a frequency of 100 MHz.

  4. Identifying electrical loads which can use direct photovoltaic dc power

    NASA Astrophysics Data System (ADS)

    Goff, H. C.; Chan, T. S.; Allred, R.; Dale, D. W.; Nichols, J. A.

    1981-11-01

    Direct current energy is used in several industrial and commercial applications including residential appliance type equipment that operates from dc, as used in recreational vehicles. These applications are reviewed to determine the potential for using photovoltaic generated power directly in the respective processes. Generally, the dc load requirements are very high or they require strict regulation. This limits the widespread introduction of PV generated power. The three most promising applications are water desalination, telephone switching stations and fluorescent lighting.

  5. An efficient switch-mode power supply using an AC-DC interleaved boost converter and a DC-DC full-bridge topology

    NASA Astrophysics Data System (ADS)

    Lessa Tofoli, Fernando; Gallo, Carlos Alberto

    2011-04-01

    This work presents the conception and analysis of a switch-mode power supply with desirable characteristics of high power factor, low harmonic distortion, regulated output voltage, and high efficiency. An interleaved boost converter associated with a nondissipative snubber is used as a preregulator stage. Additionally, a soft switching full-bridge converter is chosen as DC-DC stage. The combination of both topologies results in the proposed switch-mode power supply. Theoretical background on each one of the converters is presented and analytical results are discussed in order to validate the proposal.

  6. Human tolerogenic DC-10: perspectives for clinical applications

    PubMed Central

    2012-01-01

    Dendritic cells (DCs) are critically involved in inducing either immunity or tolerance. During the last decades efforts have been devoted to the development of ad hoc methods to manipulate DCs in vitro to enhance or stabilize their tolerogenic properties. Addition of IL-10 during monocyte-derived DC differentiation allows the induction of DC-10, a subset of human tolerogenic DCs characterized by high IL-10/IL-12 ratio and co-expression of high levels of the tolerogenic molecules HLA-G and immunoglobulin-like transcript 4. DC-10 are potent inducers of adaptive type 1 regulatory T cells, well known to promote and maintain peripheral tolerance. In this review we provide an in-depth comparison of the phenotype and mechanisms of suppression mediated by DC-10 and other known regulatory antigen-presenting cells currently under clinical development. We discuss the clinical therapeutic application of DC-10 as inducers of type 1 regulatory T cells for tailoring regulatory T-cell-based cell therapy, and the use of DC-10 as adoptive cell therapy for promoting and restoring tolerance in T-cell-mediated diseases. PMID:23369527

  7. Low-to-Medium Power Single Chip Digital Controlled DC-DC Regulator for Point-of-Load Applications

    NASA Technical Reports Server (NTRS)

    Adell, Philippe C. (Inventor); Bakkaloglu, Bertan (Inventor); Vermeire, Bert (Inventor); Liu, Tao (Inventor)

    2015-01-01

    A DC-DC converter for generating a DC output voltage includes: a digitally controlled pulse width modulator (DPWM) for controlling a switching power stage to supply a varying voltage to an inductor; and a digital voltage feedback circuit for controlling the DPWM in accordance with a feedback voltage corresponding to the DC output voltage, the digital voltage feedback circuit including: a first voltage controlled oscillator for converting the feedback voltage into a first frequency signal and to supply the first frequency signal to a first frequency discriminator; a second voltage controlled oscillator for converting a reference voltage into a second frequency signal and to supply the second frequency signal to a second frequency discriminator; a digital comparator for comparing digital outputs of the first and second frequency discriminators and for outputting a digital feedback signal; and a controller for controlling the DPWM in accordance with the digital feedback signal.

  8. Current-fed Step-up DC/DC Converter for Fuel Cell Applications with Active Overvoltage Clamping

    NASA Astrophysics Data System (ADS)

    Andreiciks, Aleksandrs; Steiks, Ingars; Krievs, Oskars

    2010-01-01

    In order to use hydrogen fuel cells in domestic applications either as main power supply or backup source, their low DC output voltage has to be matched to the level and frequency of the utility grid AC voltage. Such power converter systems usually consist of a DC-DC converter and a DC-AC inverter. A double inductor step-up push-pull converter is investigated in this paper, presenting simulation and experimental results for passive and active overvoltage clamping. The prototype of the investigated converter is elaborated for 1200 W power to match the rated power of the proton exchange membrane (PEM) fuel cell located in hydrogen fuel cell research laboratory.

  9. Integrated modeling and control of a PEM fuel cell power system with a PWM DC/DC converter

    NASA Astrophysics Data System (ADS)

    Choe, Song-Yul; Lee, Jung-Gi; Ahn, Jong-Woo; Baek, Soo-Hyun

    A fuel cell powered system is regarded as a high current and low voltage source. To boost the output voltage of a fuel cell, a DC/DC converter is employed. Since these two systems show different dynamics, they need to be coordinated to meet the demand of a load. This paper proposes models for the two systems with associated controls, which take into account a PEM fuel cell stack with air supply and thermal systems, and a PWM DC/DC converter. The integrated simulation facilitates optimization of the power control strategy, and analyses of interrelated effects between the electric load and the temperature of cell components. In addition, the results show that the proposed power control can coordinate the two sources with improved dynamics and efficiency at a given dynamic load.

  10. A Low-Cost Soft-Switched DC/DC Converter for Solid-Oxide Fuel Cells

    SciTech Connect

    Jason Lai

    2009-03-03

    A highly efficient DC to DC converter has been developed for low-voltage high-current solid oxide fuel cells. The newly developed 'V6' converter resembles what has been done in internal combustion engine that split into multiple cylinders to increase the output capacity without having to increase individual cell size and to smooth out the torque with interleaving operation. The development was started with topology overview to ensure that all the DC to DC converter circuits were included in the study. Efficiency models for different circuit topologies were established, and computer simulations were performed to determine the best candidate converter circuit. Through design optimization including topology selection, device selection, magnetic component design, thermal design, and digital controller design, a bench prototype rated 5-kW, with 20 to 50V input and 200/400V output was fabricated and tested. Efficiency goal of 97% was proven achievable through hardware experiment. This DC to DC converter was then modified in the later stage to converter 35 to 63 V input and 13.8 V output for automotive charging applications. The complete prototype was tested at Delphi with their solid oxide fuel cell test stand to verify the performance of the modified DC to DC converter. The output was tested up to 3-kW level, and the efficiency exceeded 97.5%. Multiple-phase interleaving operation design was proved to be reliable and ripple free at the output, which is desirable for the battery charging. Overall this is a very successful collaboration project between the SECA Core Technology Team and Industrial Team.

  11. A brief review of models of DC-DC power electronic converters for analysis of their stability

    NASA Astrophysics Data System (ADS)

    Siewniak, Piotr; Grzesik, Bogusław

    2014-10-01

    A brief review of models of DC-DC power electronic converters (PECs) is presented in this paper. It contains the most popular, continuous-time and discrete-time models used for PEC simulation, design, stability analysis and other applications. Both large-signal and small-signal models are considered. Special attention is paid to models that are used in practice for the analysis of the global and local stability of PECs.

  12. An Interleaved Reduced-Component-Count Multivoltage Bus DC/DC Converter for Fuel Cell Powered Electric Vehicle Applications

    SciTech Connect

    Tang, Lixin; Su, Gui-Jia

    2008-01-01

    An interleaved reduced-component-count dc/dc converter is proposed for power management in fuel cell powered vehicles with a multivoltage electric net. The converter is based on a simplified topology and can handle more power with less ripple current, therefore reducing the capacitor requirements, making it more suited for fuel cell powered vehicles in the near future. A prototype rated at 4.3 kW was built and tested to verify the proposed topology.

  13. A 1.6-kW, 110-kHz dc-dc converter optimized for IGBT's

    NASA Technical Reports Server (NTRS)

    Chen, Keming; Stuart, Thomas A.

    1993-01-01

    A full bridge dc-dc converter using a zero-current and zero-voltage switching technique is described. This circuit utilizes the characteristics of the IGBT to achieve power and frequency combinations that are much higher than previously reported for this device. Experimental results are included for a 1.6-kW, 110-kHz converter with 95 percent efficiency.

  14. A High Efficiency DC-DC Converter Topology Suitable for Distributed Large Commercial and Utility Scale PV Systems

    SciTech Connect

    Agamy, Mohammed S; Harfman-Todorovic, Maja; Elasser, Ahmed; Steigerwald, Robert L; Sabate, Juan A; Chi, Song; McCann, Adam J; Zhang, Li; Mueller, Frank

    2012-09-01

    In this paper a DC-DC power converter for distributed photovoltaic plant architectures is presented. The proposed converter has the advantages of simplicity, high efficiency, and low cost. High efficiency is achieved by having a portion of the input PV power directly fed forward to the output without being processed by the converter. The operation of this converter also allows for a simplified maximum power point tracker design using fewer measurements

  15. Digital computer simulation of inductor-energy-storage dc-to-dc converters with closed-loop regulators

    NASA Technical Reports Server (NTRS)

    Ohri, A. K.; Owen, H. A.; Wilson, T. G.; Rodriguez, G. E.

    1974-01-01

    The simulation of converter-controller combinations by means of a flexible digital computer program which produces output to a graphic display is discussed. The procedure is an alternative to mathematical analysis of converter systems. The types of computer programming involved in the simulation are described. Schematic diagrams, state equations, and output equations are displayed for four basic forms of inductor-energy-storage dc to dc converters. Mathematical models are developed to show the relationship of the parameters.

  16. Quasi-Periodicity, Chaos and Coexistence in the Time Delay Controlled Two-Cell DC-DC Buck Converter

    NASA Astrophysics Data System (ADS)

    Koubaâ, Karama; Feki, Moez

    In addition to border collision bifurcation, the time delay controlled two-cell DC/DC buck converter is shown to exhibit a chaotic behavior as well. The time delay controller adds new design parameters to the system and therefore the variation of a parameter may lead to different types of bifurcation. In this work, we present a thorough analysis of different scenarios leading to bifurcation and chaos. We show that the time delay controlled two-cell DC/DC buck converter may also exhibit a Neimark-Sacker bifurcation which for some parameter set may lead to a 2D torus that may then break yielding a chaotic behavior. Besides, the saturation of the controller can also lead to the coexistence of a stable focus and a chaotic attractor. The results are presented using numerical simulation of a discrete map of the two-cell DC/DC buck converter obtained by expressing successive crossings of Poincaré section in terms of each other.

  17. Design of high efficiency dual-mode buck DC-DC converter

    NASA Astrophysics Data System (ADS)

    Xinquan, Lai; Huali, Zeng; Qiang, Ye; Huisen, He; Shasha, Zhang; Yuqing, Sun

    2010-11-01

    A buck DC—DC switching regulator with high efficiency is implemented by automatically altering the modulation mode according to load current, and it can operate with an input range of 4.5 to 30 V. At light load current, the converter operates in skip mode. The converter enters PWM mode operation with increasing load current. It reduces the switching loss at light load and standby state, which results in prolonging battery lifetime and stand-by time. Meanwhile, externally adjustable soft-start minimizes the inrush supply current and avoids the overshoot of output voltage at initial startup. The regulator is fabricated by a 0.6 μm CDMOS process. The test results show that, under the condition of 3.3 V output, the efficiency is up to 64% at 5 mA and the maximum efficiency is 95.5%.

  18. A study of DC-DC converters with MCT's for arcjet power supplies

    NASA Technical Reports Server (NTRS)

    Stuart, Thomas A.

    1994-01-01

    Many arcjet DC power supplies use PWM full bridge converters with large arrays of parallel FET's. This report investigates an alternative supply using a variable frequency series resonant converter with small arrays of parallel MCT's (metal oxide semiconductor controlled thyristors). The reasons for this approach are to: increase reliability by reducing the number of switching devices; and decrease the surface mounting area of the switching arrays. The variable frequency series resonant approach is used because the relatively slow switching speed of the MCT precludes the use of PWM. The 10 kW converter operated satisfactorily with an efficiency of over 91 percent. Test results indicate this efficiency could be increased further by additional optimization of the series resonant inductor.

  19. Influence of 3D anisotropic structures on bipole-quadrupole DC resistivity (BQ-DC) measurements

    NASA Astrophysics Data System (ADS)

    Loewer, A.; Junge, A.; Guenther, T.; Grinat, M.; Hering, P.

    2015-12-01

    3D modelling of BQ-DC measurements can show a rather strong directional distortion of the electric current density for an inhomogeneous subsurface. Anisotropic structures increase this effect. Depending on the anisotropy direction, current density might vary by 90° between the interior and exterior of an anisotropic body. In combination with 3D effects currents might even flow into the opposite direction compared to those expected for a homogeneous half space. This effect can produce negative potential differences (in combination with positive geometry factors) at the surface which cannot be explained by an isotropic resistivity distribution and thus those data cannot be used by an isotropic inversion. Consequently, anisotropic forward modelling is necessary to explain such observations. In nature anisotropic resistivity can appear in the context of strongly foliated structures. Such structures exist in the Rhenish Massif, Germany, where extensive shallow greywacke shales with different strength of foliation are found. In this area a field campaign was performed in 2014 to provide evidence for the existence of anisotropic resistivity structures. Two perpendicular bipole current injections at 15 locations produced individual potential distributions. The potential differences were recorded for two orthogonal directions each at 30 positions for an array set up within the survey area. We use the apparent resistivity tensor after Bibby 1986 to display the BQ-DC data. It uses the hypothetical current densities of each of the two bipole sources calculated for an equivalent homogenous half space at the location of the quadrupole measurement to derive a resistivity tensor. The spatial behavior of modelled tensors gives evidence of the anisotropic body although the structure is covered by an isotropic layer. The data are explained by a 3D anisotropic resistivity distribution using a 3D isotropic inversion scheme combined with 3D anisotropic forward-modelling.

  20. Tests on conducted electrical noise on a storage ring dc-dc converter cabinet

    SciTech Connect

    Carwardine, J.J.

    1994-02-22

    Electrical noise is produced by switching transients in the power supply converters which excite resonances formed by stray capacitance and cable inductance. This noise is present not only on the load cables, but also on ground cables of the magnet and of the converter cabinet. Since there will eventually be a large number of cabinets running at one time, tests were carried out to characterize the noise and to investigate possible techniques for reducing the levels. The tests were carried out on the test girder and converter cabinet set up in 412 area. There were four magnets installed on the girder -- two 0.5m quadrupoles, a 0.8m quadrupole, and a sextupole. These tests were carried out on one of the 0.5m quadrupoles. It should be noted that with this setup, the raw dc power was supplied at around 70V. In the final configuration, a 0.5m quad will be fed from a 40V raw supply. Consequently, the switching transients observed during the tests are likely to be higher than will occur in reality. Noise currents contain two main components: a low frequency component at around 50kHz, and a higher frequency component at around lMHz. It is the latter component which is of primary concern. Currents measured on the dc load cables typically were around one ampere, while currents into the building ground system were only a few tens of milliamps. Several methods were used to try reducing the noise currents, but only the addition of a series impedance was successful -- other methods either had no effect or increased the ground currents.

  1. 77 FR 74347 - Prevailing Rate Systems; Abolishment of the Washington, DC, Special Wage Schedule for Printing...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-12-14

    ... RIN 3206-AM59 Prevailing Rate Systems; Abolishment of the Washington, DC, Special Wage Schedule for.... Office of Personnel Management is issuing a final rule to abolish the Washington, DC, Federal Wage System... employees in the Washington, DC, wage area will now be paid from the regular Washington, DC,...

  2. Symmetrical dynamics of peak current-mode and valley current-mode controlled switching dc-dc converters with ramp compensation

    NASA Astrophysics Data System (ADS)

    Zhou, Guo-Hua; Xu, Jian-Ping; Bao, Bo-Cheng; Jin, Yan-Yan

    2010-06-01

    The discrete iterative map models of peak current-mode (PCM) and valley current-mode (VCM) controlled buck converters, boost converters, and buck-boost converters with ramp compensation are established and their dynamical behaviours are investigated by using the operation region, parameter space map, bifurcation diagram, and Lyapunov exponent spectrum. The research results indicate that ramp compensation extends the stable operation range of the PCM controlled switching dc-dc converter to D > 0.5 and that of the VCM controlled switching dc-dc converter to D < 0.5. Compared with PCM controlled switching dc-dc converters with ramp compensation, VCM controlled switching dc-dc converters with ramp compensation exhibit interesting symmetrical dynamics. Experimental results are given to verify the analysis results in this paper.

  3. Experience from design, prototyping and production of a DC-DC conversion powering scheme for the CMS Phase-1 Pixel Upgrade

    NASA Astrophysics Data System (ADS)

    Feld, L.; Karpinski, W.; Klein, K.; Lipinski, M.; Preuten, M.; Rauch, M.; Schmitz, S.; Wlochal, M.

    2016-02-01

    The CMS collaboration has adopted a DC-DC conversion powering scheme for the Phase-1 Upgrade of its pixel detector. DC-DC buck converters with a conversion ratio of around 3 are installed on the support structures, outside of the sensitive tracking region, requiring a re-design of the low and high voltage distribution to the pixel modules. After several years of R&D, the project has entered the production phase. A total of 1800 DC-DC converters are being produced, and rigorous quality assurance and control is being employed during the production process. The testing program is outlined, results from mass production are presented and issues that have been encountered are described. In addition, two system level challenges, namely the choice of output voltage in the presence of large, load-dependent voltage drops, and the thermal management required to remove the heat load caused by the DC-DC converters, are discussed.

  4. DC Microgrids Scoping Study. Estimate of Technical and Economic Benefits

    SciTech Connect

    Backhaus, Scott N.; Swift, Gregory William; Chatzivasileiadis, Spyridon; Tschudi, William; Glover, Steven; Starke, Michael; Wang, Jianhui; Yue, Meng; Hammerstrom, Donald

    2015-03-23

    Microgrid demonstrations and deployments are expanding in US power systems and around the world. Although goals are specific to each site, these microgrids have demonstrated the ability to provide higher reliability and higher power quality than utility power systems and improved energy utilization. The vast majority of these microgrids are based on AC power transfer because this has been the traditionally dominant power delivery scheme. Independently, manufacturers, power system designers and researchers are demonstrating and deploying DC power distribution systems for applications where the end-use loads are natively DC, e.g., computers, solid-state lighting, and building networks. These early DC applications may provide higher efficiency, added flexibility, reduced capital costs over their AC counterparts. Further, when onsite renewable generation, electric vehicles and storage systems are present, DC-based microgrids may offer additional benefits. Early successes from these efforts raises a question - can a combination of microgrid concepts and DC distribution systems provide added benefits beyond what has been achieved individually?

  5. Results of winglet development studies for DC-10 derivatives

    NASA Technical Reports Server (NTRS)

    Shollenberger, C. A.; Humphreys, J. W.; Heiberger, F. S.; Pearson, R. M.

    1983-01-01

    The results of investigations into the application of winglets to the DC-10 aircraft are presented. The DC-10 winglet configuration was developed and its cruise performance determined in a previous investigation. This study included high speed and low speed wind tunnel tests to evaluate aerodynamic characteristics, and a subsonic flutter wind tunnel test with accompanying analysis and evaluation of results. Additionally, a configuration integration study employed the results of the wind tunnel studies to determine the overall impact of the installation of winglets on the DC-10 aircraft. Conclusions derived from the high speed and low speed tests indicate that the winglets had no significant effects on the DC-10 stability characteristics or high speed buffet. It was determined that winglets had a minimal effect on aircraft lift characteristics and improved the low speed aircraft drag under high lift conditions. The winglets affected the DC-10 flutter characteristics by reducing the flutter speed of the basic critical mode and introducing a new critical mode involving outer wing torsion and longitudinal bending. The overall impact of winglets was determined to be of sufficient benefit to merit flight evaluation.

  6. Pseudo-Mannosylated DC-SIGN Ligands as Immunomodulants

    PubMed Central

    Berzi, Angela; Ordanini, Stefania; Joosten, Ben; Trabattoni, Daria; Cambi, Alessandra; Bernardi, Anna; Clerici, Mario

    2016-01-01

    DC-SIGN, a C-type lectin mainly expressed by DCs, mediates antigen uptake and can induce specific immune responses, depending on the ligand involved. Owing to these properties, DC-SIGN is an attracting target for approaches aimed at tailoring the immune response towards specific immunologic outcomes. A multivalent DC-SIGN ligand (Polyman26), containing at its core a fluorescent “rod-like” spacer and able to inhibit DC-SIGN mediated HIV infection in nanomolar concentration, has been recently developed by our group. We investigated the internalization pattern and the ability of Polyman26 to elicit innate immune responses. Results obtained by confocal microscopy indicate that Polyman26 is internalized by DCs via receptor- mediated endocytosis and is then routed to endolysosomal compartments, thus being presented together with MHC class II molecules, with important implications for the development of vaccines. Moreover, Polyman26 up-regulated the production of β-chemokines and pro-inflammatory cytokines (including IL-1β, IL-6, IL-12, and TNFα) as well as the expression of TLR9 and CD40L. These results indicate that glycomimetic DC-SIGN ligands should be further investigated and suggest that these compounds could be used to differentially stimulate immune responses. PMID:27734954

  7. Suppression of spatially periodic patterns by dc voltage

    NASA Astrophysics Data System (ADS)

    Éber, Nándor; Salamon, Péter; Fekete, Balázs András; Karapinar, Ridvan; Krekhov, Alexei; Buka, Ágnes

    2016-04-01

    The effect of superposed dc and ac applied voltages on two types of spatially periodic instabilities in nematic liquid crystals, flexoelectric domains (FD), and electroconvection (EC) was studied. The onset characteristics, threshold voltages, and critical wave vectors were determined. We found that in general the superposition of driving with different time symmetries inhibits the pattern forming mechanisms for FD and EC as well. As a consequence, the onset extends to much higher voltages than the individual dc or ac thresholds. A dc-bias-induced reduction of the crossover frequency from the conductive to the dielectric EC regimes and a peculiar transition between two types of flexodomains with different wavelengths were detected. Direct measurements of the change of the electrical conductivity and its anisotropy, induced by the applied dc voltage component, showed that the dc bias substantially affects both parameters. Taking into account the experimentally detected variations of the conductivity in the linear stability analysis of the underlying nematohydrodynamic equations, a qualitative agreement with the experimental findings on the onset behavior of spatially periodic instabilities was obtained.

  8. SLE-associated risk factors affect DC function.

    PubMed

    Son, Myoungsun; Kim, Sun Jung; Diamond, Betty

    2016-01-01

    Numerous risk alleles for systemic lupus erythematosus (SLE) have now been identified. Analysis of the expression of genes with risk alleles in cells of hematopoietic origin demonstrates them to be most abundantly expressed in B cells and dendritic cells (DCs), suggesting that these cell types may be the drivers of the inflammatory changes seen in SLE. DCs are of particular interest as they act to connect the innate and the adaptive immune response. Thus, DCs can transform inflammation into autoimmunity, and autoantibodies are the hallmark of SLE. In this review, we focus on mechanisms of tolerance that maintain DCs in a non-activated, non-immunogenic state. We demonstrate, using examples from our own studies, how alterations in DC function stemming from either DC-intrinsic abnormalities or DC-extrinsic regulators of function can predispose to autoimmunity.

  9. Magnetoencephalography using a Multilayer hightc DC SQUID Magnetometer

    NASA Astrophysics Data System (ADS)

    Faley, M. I.; Poppe, U.; Borkowski, R. E. Dunin; Schiek, M.; Boers, F.; Chocholacs, H.; Dammers, J.; Eich, E.; Shah, N. J.; Ermakov, A. B.; Slobodchikov, V. Yu.; Maslennikov, Yu. V.; Koshelets, V. P.

    We describe tests of the use of a multilayer highTc DC SQUID magnetometer for magnetoencephalography (MEG) and compare our measurements with results obtained using a lowTc SQUID sensor. The integration of bias reversal readout electronics for highTc DC SQUID magnetometry into a commercial MEG data acquisition system is demonstrated. Results of measurements performed on a salinefilled head phantom are shown and the detection of an auditory evoked magnetic response of the human cortex elicited by a stimulus is illustrated. Future modifications of highTc DC SQUID sensors for applications in MEG, in order to reach a resolution of 1 fT/√Hz at 77.5 K over a wide frequency band, are outlined.

  10. Imaging DC MEG Fields Associated with Epileptic Onset

    NASA Astrophysics Data System (ADS)

    Weiland, B. J.; Bowyer, S. M.; Moran, J. E.; Jenrow, K.; Tepley, N.

    2004-10-01

    Magnetoencephalography (MEG) is a non-invasive brain imaging modality, with high spatial and temporal resolution, used to evaluate and quantify the magnetic fields associated with neuronal activity. Complex partial epileptic seizures are characterized by hypersynchronous neuronal activity believed to arise from a zone of epileptogenesis. This study investigated the characteristics of direct current (DC) MEG shifts arising at epileptic onset. MEG data were acquired with rats using a six-channel first order gradiometer system. Limbic status epilepticus was induced by IA (femoral) administration of kainic acid. DC-MEG shifts were observed at the onset of epileptic spike train activity and status epilepticus. Epilepsy is also being studied in patients undergoing presurgical mapping from the Comprehensive Epilepsy Center at Henry Ford Hospital using a whole head Neuromagnetometer. Preliminary data analysis shows that DC-MEG waveforms, qualitatively similar to those seen in the animal model, are evident prior to seizure activity in human subjects.

  11. SLE-associated risk factors affect DC function.

    PubMed

    Son, Myoungsun; Kim, Sun Jung; Diamond, Betty

    2016-01-01

    Numerous risk alleles for systemic lupus erythematosus (SLE) have now been identified. Analysis of the expression of genes with risk alleles in cells of hematopoietic origin demonstrates them to be most abundantly expressed in B cells and dendritic cells (DCs), suggesting that these cell types may be the drivers of the inflammatory changes seen in SLE. DCs are of particular interest as they act to connect the innate and the adaptive immune response. Thus, DCs can transform inflammation into autoimmunity, and autoantibodies are the hallmark of SLE. In this review, we focus on mechanisms of tolerance that maintain DCs in a non-activated, non-immunogenic state. We demonstrate, using examples from our own studies, how alterations in DC function stemming from either DC-intrinsic abnormalities or DC-extrinsic regulators of function can predispose to autoimmunity. PMID:26683148

  12. DESIGN OF A DC/RF PHOTOELECTRON GUN.

    SciTech Connect

    YU,D.NEWSHAM,Y.SMIRONOV,A.YU,J.SMEDLEY,J.SRINIVASAN RAU,T.LEWELLEN,J.ZHOLENTS,A.

    2003-05-12

    An integrated dc/rf photoelectron gun produces a low-emittance beam by first rapidly accelerating electrons at a high gradient during a short ({approx}1 ns), high-voltage pulse, and then injecting the electrons into an rf cavity for subsequent acceleration. Simulations show that significant improvement of the emittance appears when a high field ({approx} 0.5-1 GV/m) is applied to the cathode surface. An adjustable dc gap ({le} 1 mm) which can be integrated with an rf cavity is designed for initial testing at the Injector Test Stand at Argonne National Laboratory using an existing 70-kV pulse generator. Plans for additional experiments of an integrated dc/rf gun with a 250-kV pulse generator are being made.

  13. SLE-associated risk factors affect DC function

    PubMed Central

    Son, Myoungsun; Kim, Sun Jung; Diamond, Betty

    2016-01-01

    Numerous risk alleles for systemic lupus erythematosus (SLE) have now been identified. Analysis of the expression of genes with risk alleles in cells of hematopoietic origin demonstrates them to be most abundantly expressed in B cells and dendritic cells (DCs), suggesting that these cell types may be the drivers of the inflammatory changes seen in SLE. DCs are of particular interest as they act to connect the innate and the adaptive immune response. Thus, DCs can transform inflammation into autoimmunity, and autoantibodies are the hallmark of SLE. In this review, we focus on mechanisms of tolerance that maintain DCs in a non-activated, non-immunogenic state. We demonstrate, using examples from our own studies, how alterations in DC function stemming from either DC-intrinsic abnormalities or DC-extrinsic regulators of function can predispose to autoimmunity. PMID:26683148

  14. Photovoltaic-wind hybrid system for permanent magnet DC motor

    NASA Astrophysics Data System (ADS)

    Nasir, M. N. M.; Lada, M. Y.; Baharom, M. F.; Jaafar, H. I.; Ramani, A. N.; Sulaima, M. F.

    2015-05-01

    Hybrid system of Photovoltaic (PV) - Wind turbine (WT) generation has more advantages and reliable compared to PV or wind turbine system alone. The aim of this paper is to model and design hybrid system of PV-WT supplying 100W permanent-magnet dc motor. To achieve the objective, both of PV and WT are connected to converter in order to get the same source of DC supply. Then both sources were combined and straightly connected to 100W permanent magnet dc motor. All the works in this paper is only applied in circuit simulator by using Matlab Simulink. The output produced from each converter is expected to be suit to the motor specification. The output produced from each renewable energy system is as expected to be high as it can support the motor if one of them is breakdown

  15. Diagnostic of water trees using DC and AC voltages

    SciTech Connect

    Romero, P.; Puerta, J.

    1996-12-31

    Electric tools for non-destructive water tree diagnostic in XLPE medium voltage cables, by means of DC and AC voltages are presented. The DC method is related to the determination of a non-linear dependence of the polarization current on the applied DC step voltage, in contrast to a linear dependence found in non-water tree-damaged cables. In both cases the current follows the Curie-von Schweidler empirical law, I(t) = I{sub 0}t{sup {minus}n}. The AC method is based on the measurement of the dispersion relation of both the loss factor and the capacitance in the low and very low frequency ranges by means of the Fourier Transform techniques. The devised measuring instrumentation is presented.

  16. IMPLEMENTING THE DC MODE IN COSMOLOGICAL SIMULATIONS WITH SUPERCOMOVING VARIABLES

    SciTech Connect

    Gnedin, Nickolay Y.; Kravtsov, Andrey V.; Rudd, Douglas H. E-mail: andrey@oddjob.uchicago.edu

    2011-06-01

    As emphasized by previous studies, proper treatment of the density fluctuation on the fundamental scale of a cosmological simulation volume-the {sup D}C mode{sup -}is critical for accurate modeling of spatial correlations on scales {approx}> 10% of simulation box size. We provide further illustration of the effects of the DC mode on the abundance of halos in small boxes and show that it is straightforward to incorporate this mode in cosmological codes that use the 'supercomoving' variables. The equations governing evolution of dark matter and baryons recast with these variables are particularly simple and include the expansion factor, and hence the effect of the DC mode, explicitly only in the Poisson equation.

  17. Nuclear magnetic resonance experiments with dc SQUID amplifiers

    SciTech Connect

    Heaney, M.B. . Dept. of Physics Lawrence Berkeley Lab., CA )

    1990-11-01

    The development and fabrication of dc SQUIDs (Superconducting QUantum Interference Devices) with Nb/Al{sub 2}O{sub 3}/Nb Josephson junctions is described. A theory of the dc SQUID as a radio-frequency amplifier is presented, with an optimization strategy that accounts for the loading and noise contributions of the postamplifier and maximizes the signal-to-noise ratio of the total system. The high sensitivity of the dc SQUID is extended to high field NMR. A dc SQUID is used as a tuned radio-frequency amplifier to detect pulsed nuclear magnetic resonance at 32 MHz from a metal film in a 3.5 Tesla static field. A total system noise temperature of 11 K has been achieved, at a bath temperature of 4.2 K. The minimum number of nuclear Bohr magnetons observable from a free precession signal after a single pulse is about 2 {times} 10{sup 17} in a bandwidth of 25 kHz. In a separate experiment, a dc SQUID is used as a rf amplifier in a NQR experiment to observe a new resonance response mechanism. The net electric polarization of a NaClO{sub 3} crystal due to the precessing electric quadrupole moments of the Cl nuclei is detected at 30 MHz. The sensitivity of NMR and NQR spectrometers using dc SQUID amplifiers is compared to the sensitivity of spectrometers using conventional rf amplifiers. A SQUID-based spectrometer has a voltage sensitivity which is comparable to the best achieved by a FET-based spectrometer, at these temperatures and operating frequencies.

  18. The effect of a helicopter on DC fields and ions

    SciTech Connect

    Harris, E.L. ); Rindall, B.D.; Tarko, N.J. ); Norris-Elye, O.C. )

    1993-10-01

    When a plan was initiated to utilize a helicopter to perform work on an energized, high voltage dc transmission line by bonding the helicopter to the conductor, it was necessary to determine what effect, if any, the helicopter would have on the dc fields and ions. In addition, it was necessary to determine the possible effect on helicopter instrumentation and communications. A test site and research facility at Lundar, Manitoba, Canada, provided the ideal location for making these tests. As a result, the information obtained determined that a helicopter-airborne platform could safely be used to perform the work.

  19. The Basic Properties of PPLP for HTS DC Cable

    NASA Astrophysics Data System (ADS)

    Kim, W. J.; Kim, H. J.; Cho, J. W.; Kim, S. H.

    In order to develop high temperature superconducting (HTS) DC cable, it is important to understand the cooling system, high voltage insulation and materials at cryogenic temperature. Especially, the basic properties of insulating materials must be solved for the long life, reliability and compact of system. In this paper, we will discuss mainly on the electrical and the mechanical properties of polypropylene laminated paper (PPLP) in liquid nitrogen (LN2). The polarity effect of DC and impulse voltage, the volume resistivity and the space charge distribution and frost were studied. Furthermore, the mechanical properties such as tensile strength of PPLP at LN2 (77 K) and room temperature (300 K) were studied.

  20. Controller for computer control of brushless dc motors

    NASA Astrophysics Data System (ADS)

    Hieda, L. S.

    1981-02-01

    A motor speed and torque controller for brushless d.c. motors provides an unusually smooth torque control arrangement. The controller provides a means for controlling a current waveform in each winding of a brushless dc motor by synchronization of an excitation pulse train from a programmable oscillator. Sensing of torque for synchronization is provided by a light beam chopper mounted on the motor rotor shaft. Speed and duty cycle are independently controlled by controlling the frequency and pulse width output of the programmable oscillator. A means is also provided so that current transitions from one motor winding to another is effected without abrupt changes in output torque.

  1. Controller for computer control of brushless dc motors. [automobile engines

    NASA Technical Reports Server (NTRS)

    Hieda, L. S. (Inventor)

    1981-01-01

    A motor speed and torque controller for brushless d.c. motors provides an unusually smooth torque control arrangement. The controller provides a means for controlling a current waveform in each winding of a brushless dc motor by synchronization of an excitation pulse train from a programmable oscillator. Sensing of torque for synchronization is provided by a light beam chopper mounted on the motor rotor shaft. Speed and duty cycle are independently controlled by controlling the frequency and pulse width output of the programmable oscillator. A means is also provided so that current transitions from one motor winding to another is effected without abrupt changes in output torque.

  2. Dissociation curves of diatomic molecules: A DC-DFT study

    SciTech Connect

    Sim, Eunji; Kim, Min-Cheol; Burke, Kieron

    2015-12-31

    We investigate dissociation of diatomic molecules using standard density functional theory (DFT) and density-corrected density functional theory (DC-DFT) compared with CCSD(T) results as reference. The results show the difference between the HOMO values of dissociated atomic species often can be used as an indicator whether DFT would predict the correct dissociation limit. DFT predicts incorrect dissociation limits and charge distribution in molecules or molecular ions when the fragments have large HOMO differences, while DC-DFT and CCSD(T) do not. The criteria for large HOMO difference is about 2 ∼ 4 eV.

  3. Graphite electrode DC arc furnace. Innovative technology summary report

    SciTech Connect

    1999-05-01

    The Graphite Electrode DC Arc Furnace (DC Arc) is a high-temperature thermal process, which has been adapted from a commercial technology, for the treatment of mixed waste. A DC Arc Furnace heats waste to a temperature such that the waste is converted into a molten form that cools into a stable glassy and/or crystalline waste form. Hazardous organics are destroyed through combustion or pyrolysis during the process and the majority of the hazardous metals and radioactive components are incorporated in the molten phase. The DC Arc Furnace chamber temperature is approximately 593--704 C and melt temperatures are as high as 1,500 C. The DC Arc system has an air pollution control system (APCS) to remove particulate and volatiles from the offgas. The advantage of the DC Arc is that it is a single, high-temperature thermal process that minimizes the need for multiple treatment systems and for extensive sorting/segregating of large volumes of waste. The DC Arc has the potential to treat a wide range of wastes, minimize the need for sorting, reduce the final waste volumes, produce a leach resistant waste form, and destroy organic contaminants. Although the DC arc plasma furnace exhibits great promise for treating the types of mixed waste that are commonly present at many DOE sites, several data and technology deficiencies were identified by the Mixed Waste Focus Area (MWFA) regarding this thermal waste processing technique. The technology deficiencies that have been addressed by the current studies include: establishing the partitioning behavior of radionuclides, surrogates, and hazardous metals among the product streams (metal, slag, and offgas) as a function of operating parameters, including melt temperature, plenum atmosphere, organic loading, chloride concentration, and particle size; demonstrating the efficacy of waste product removal systems for slag and metal phases; determining component durability through test runs of extended duration, evaluating the effect of

  4. Two junction effects in dc SQUID phase qubit

    NASA Astrophysics Data System (ADS)

    Cooper, B. K.; Kwon, H.; Przybysz, A. J.; Budoyo, R.; Anderson, J. R.; Lobb, C. J.; Wellstood, F. C.

    2011-03-01

    The dc SQUID phase qubit was designed to allow one isolation junction to filter bias current noise from a second junction operating as a single junction phase qubit. As junctions shrink to minimize dielectric loss, the Josephson inductances of each junction approach the coupling loop inductance and this single junction picture appears inadequate. We consider a two-junction model of the dc SQUID phase qubit, where the qubit now corresponds to one of the normal oscillatory modes of the full SQUID. We discuss applications of this model to sweet spots in various control parameters and unusual behavior in the tunneling state measurement. Funded by DOD, CNAM and JQI.

  5. High voltage dc-dc converter with dynamic voltage regulation and decoupling during load-generated arcs

    DOEpatents

    Shimer, Daniel W.; Lange, Arnold C.

    1995-01-01

    A high-power power supply produces a controllable, constant high voltage output under varying and arcing loads. The power supply includes a voltage regulator, an inductor, an inverter for producing a high frequency square wave current of alternating polarity, an improved inverter voltage clamping circuit, a step up transformer, an output rectifier for producing a dc voltage at the output of each module, and a current sensor for sensing output current. The power supply also provides dynamic response to varying loads by controlling the voltage regulator duty cycle and circuitry is provided for sensing incipient arc currents at the output of the power supply to simultaneously decouple the power supply circuitry from the arcing load. The power supply includes a plurality of discrete switching type dc--dc converter modules.

  6. High voltage dc--dc converter with dynamic voltage regulation and decoupling during load-generated arcs

    DOEpatents

    Shimer, D.W.; Lange, A.C.

    1995-05-23

    A high-power power supply produces a controllable, constant high voltage output under varying and arcing loads. The power supply includes a voltage regulator, an inductor, an inverter for producing a high frequency square wave current of alternating polarity, an improved inverter voltage clamping circuit, a step up transformer, an output rectifier for producing a dc voltage at the output of each module, and a current sensor for sensing output current. The power supply also provides dynamic response to varying loads by controlling the voltage regulator duty cycle and circuitry is provided for sensing incipient arc currents at the output of the power supply to simultaneously decouple the power supply circuitry from the arcing load. The power supply includes a plurality of discrete switching type dc--dc converter modules. 5 Figs.

  7. Regulated dc-to-dc converter for voltage step-up or step-down with input-output isolation

    NASA Technical Reports Server (NTRS)

    Feng, S. Y.; Wilson, T. G. (Inventor)

    1973-01-01

    A closed loop regulated dc-to-dc converter employing an unregulated two winding inductive energy storage converter is provided by using a magnetically coupled multivibrator acting as duty cycle generator to drive the converter. The multivibrator is comprised of two transistor switches and a saturable transformer. The output of the converter is compared with a reference in a comparator which transmits a binary zero until the output exceeds the reference. When the output exceeds the reference, the binary output of the comparator drives transistor switches to turn the multivibrator off. The multivibrator is unbalanced so that a predetermined transistor will always turn on first when the binary feedback signal becomes zero.

  8. Design of Performance Driven Self-Tuning PID Control Systems and It's Application for DC-DC Converters

    NASA Astrophysics Data System (ADS)

    Ohnishi, Yoshihiro; Ikemoto, Takahiro; Yamamoto, Toru

    This paper proposes an adaptive PID controller which is driven by current control performance. The calculations of the PID parameters are based on the generalized minimum variance control(GMVC) algorithm. The current control performance is obtained in an online manner over a user-specified time-window with some overlap. The retuning of PID parameters are only carried out when controller performance deteriorates below a user-specified threshold. Experimental evaluations on the voltage control of the DC-DC converter demonstrates the practicality and utility of this idea.

  9. Application of Multi-port Bidirectional DC-DC Converter to Fuel Cell Vehicle Driving in JC08 Mode

    NASA Astrophysics Data System (ADS)

    Tanaka, Katsunori; Katayama, Noboru; Kogoshi, Sumio; Fukada, Takafumi; Ogawa, Makoto

    A fuel cell-EDLC hybrid power system with a multi-port bidirectional DC-DC converter has been recently proposed for extending lifetime of a fuel cell due to smoothing the output current of the fuel cell. This paper studies the performance of the hybrid power system when a fuel cell vehicle drives in the JC08 mode using a simulation model. The simulation results indicate that even if the load current fluctuates, the output current of the fuel cell could be maintained at almost constant values with an assist from the EDLC although small spikes are observed.

  10. A controller resetting strategy for the stabilization of DC-to-DC power converters towards non-minimum phase equilibria

    SciTech Connect

    Llanes-Santiago, O.; Sira-Ramirez, H.

    1994-12-31

    A feedback resetting strategy, exercised on the output of a purposely designed unstable dynamical feedback controller, is shown to yield a robust, and efficient, output voltage stabilization of nonlinear average models of DC-to-DC Power Converters around any non-minimum phase equilibrium point of the system. The technique guarantees, in an average sense, an asymptotically stable behavior of the controlled converter state variables towards their required equilibrium values, while the unstable dynamical compensator output is forcefully kept bounded within an arbitrarily small neighborhood of the required controller operating point.

  11. Discrete time domain modelling and analysis of dc-dc converters with continuous and discontinuous inductor current

    NASA Technical Reports Server (NTRS)

    Iwens, R. P.; Lee, F. C.; Triner, J. E.

    1977-01-01

    Using discrete time state variable representation, a generalized computer-aided modeling and analysis of dc-dc converters is presented. The methodology provides exact modeling and is applicable to all types of power stages and duty-cycle control, including continuous and discontinuous inductor current operation. Converter stability, transient behavior and audio susceptibility can be analytically evaluated and predicted. The generalized theory of the proposed approach to converter modeling and analysis is presented first, followed by a demonstrative example applying the theory to a constant frequency buck converter operating in continuous and discontinuous inductor current mode. Excellent agreement with laboratory test data has been observed.

  12. ASDTIC control and standardized interface circuits applied to buck, parallel and buck-boost dc to dc power converters

    NASA Technical Reports Server (NTRS)

    Schoenfeld, A. D.; Yu, Y.

    1973-01-01

    Versatile standardized pulse modulation nondissipatively regulated control signal processing circuits were applied to three most commonly used dc to dc power converter configurations: (1) the series switching buck-regulator, (2) the pulse modulated parallel inverter, and (3) the buck-boost converter. The unique control concept and the commonality of control functions for all switching regulators have resulted in improved static and dynamic performance and control circuit standardization. New power-circuit technology was also applied to enhance reliability and to achieve optimum weight and efficiency.

  13. Regulated dc-to-dc converter for voltage step-up or step-down with input-output isolation.

    NASA Technical Reports Server (NTRS)

    Feng, S. Y. M.; Wilson, T. G.; Dakermandji, G.; Lee, F. C. Y.

    1971-01-01

    A dc-to-dc regulated-converter circuit employing duty-cycle control with variable on and variable off time has been presented. A unique feature of this converter is the method by which the bistable-comparator output controls the duty cycle of the power switching transistor through the action of the encoder. The utilization of minor-loop flux excursions of a saturable-core transformer in the encoder makes it feasible to extend the converter switching frequency considerably higher than would normally be possible. With this converter circuit, high and very-high frequency converter operations were explored.

  14. Evaporation of nanofluid droplets with applied DC potential.

    PubMed

    Orejon, Daniel; Sefiane, Khellil; Shanahan, Martin E R

    2013-10-01

    A considerable growth of interest in electrowetting (EW) has stemmed from the potential exploitation of this technique in numerous industrial and biological applications, such as microfluidics, lab-on-a-chip, electronic paper, and bioanalytical techniques. The application of EW to droplets of liquids containing nanoparticles (nanofluids) is a new area of interest. Understanding the effects of electrowetting at the fundamental level and being able to manipulate deposits from nanofluid droplets represents huge potential. In this work, we study the complete evaporation of nanofluid droplets under DC conditions. Different evolutions of contact angle and contact radius, as well as deposit patterns, are revealed. When a DC potential is applied, continuous and smoother receding of the contact line during the drying out of TiO2 nanofluids and more uniform patterning of the deposit are observed, in contrast to the typical "stick-slip" behavior and rings stains. Furthermore, the mechanisms for nanoparticle interactions with the applied DC potential differ from those proposed for the EW of droplets under AC conditions. The more uniform patterns of particle deposits resulting from DC potential are a consequence of a shorter timescale for electrophoretic mobility than advection transport driven by evaporation.

  15. A fully integrated neural recording amplifier with DC input stabilization.

    PubMed

    Mohseni, Pedram; Najafi, Khalil

    2004-05-01

    This paper presents a low-power low-noise fully integrated bandpass operational amplifier for a variety of biomedical neural recording applications. A standard two-stage CMOS amplifier in a closed-loop resistive feedback configuration provides a stable ac gain of 39.3 dB at 1 kHz. A subthreshold PMOS input transistor is utilized to clamp the large and random dc open circuit potentials that normally exist at the electrode-electrolyte interface. The low cutoff frequency of the amplifier is programmable up to 50 Hz, while its high cutoff frequency is measured to be 9.1 kHz. The tolerable dc input range is measured to be at least +/- 0.25 V with a dc rejection factor of at least 29 dB. The amplifier occupies 0.107 mm2 in die area, and dissipates 115 microW from a 3 V power supply. The total measured input-referred noise voltage in the frequency range of 0.1-10 kHz is 7.8 microVrms. It is fabricated using AMI 1.5 microm double-poly double-metal n-well CMOS process. This paper presents full characterization of the dc, ac, and noise performance of this amplifier through in vitro measurements in saline using two different neural recording electrodes. PMID:15132510

  16. DC-STAMP: A Key Regulator in Osteoclast Differentiation

    PubMed Central

    CHIU, YA-HUI; RITCHLIN, CHRISTOPHER T.

    2016-01-01

    Osteoimmunology research is a new emerging research field that investigates the links between the bone and immune responses. Results from osteoimmunology studies suggest that bone is not only an essential component of the musculoskeletal system, but is also actively involved in immune regulation. Many important factors involved in immune regulation also participate in bone homeostasis. Bone homeostasis is achieved by a coordinated action between bone synthesizing osteoblasts and bone degrading osteoclasts. An imbalanced action between osteoblasts and osteoclasts often results in pathological bone diseases: osteoporosis is caused by an excessive osteoclast activity, whereas osteopetrosis results from an increased osteoblast activity. This review focuses on dendritic cell specific transmembrane protein (DC STAMP), an important protein currently considered as a master regulator of osteoclastogenesis. Of clinical relevance, the frequency of circulating DC STAMPþ cells is elevated during the pathogenesis of psoriatic diseases. Intriguingly, recent results suggest that DC STAMP also plays an imperative role in bone homeostasis by regulating the differentiation of both osteoclasts and osteoblasts. This article summarizes our current knowledge on DC STAMP by focusing on its interacting proteins, its regulation on osteoclastogenesis related genes, its possible involvement in immunoreceptor tyrosine based inhibitory motif (ITIM) mediated signaling cascade, and its potential of developing therapeutics for clinical applications. PMID:27018136

  17. 38 CFR 3.851 - St. Elizabeths Hospital, Washington, DC.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 38 Pensions, Bonuses, and Veterans' Relief 1 2010-07-01 2010-07-01 false St. Elizabeths Hospital... Institutional Awards § 3.851 St. Elizabeths Hospital, Washington, DC. Benefits due or becoming due any person who is a patient at St. Elizabeths Hospital will be paid to a duly appointed fiduciary of such...

  18. DC drive system for cine/pulse cameras

    NASA Technical Reports Server (NTRS)

    Gerlach, R. H.; Sharpsteen, J. T.; Solheim, C. D.; Stoap, L. J.

    1977-01-01

    Camera-drive functions are separated mechanically into two groups which are driven by two separate dc brushless motors. First motor, a 90 deg stepper, drives rotating shutter; second electronically commutated motor drives claw and film transport. Shutter is made of one piece but has two openings for slow and fast exposures.

  19. A citywide breeding bird survey for Washington, DC

    USGS Publications Warehouse

    Hadidian, J.; Sauer, J.R.; Swarth, C.; Handly, P.; Droege, S.; Williams, C.; Huff, J.; Didden, G.

    1997-01-01

    `DC Birdscape' was initiated in 1993 to systematically count the birds occurring throughout Washington D.C. during the breeding season. It involved a coordinated planning effort and partnership between the Audubon Naturalist Society, the National Park Service, and the National Biological Survey, and engaged the participation of more than 100 volunteers. A method for rapidly assessing the status of bird populations over a large area was developed and incorporated into a Geographic Information System to allow a multidimensional analysis of species presence and abundance across a variety of urban land use areas. A total of 91 species were observed, with an estimated total number of 115, making Washington D.C. almost as `bird rich' as nearby suburban counties. Data from the study clearly indicate that avian species are not randomly distributed throughout the Washington D.C. metropolitan area, and show affinity, at least in part, to some of the most broadly recognized land use patterns that are commonly used to zone and classify urban areas under development schemes. This study represents a prototype that will allow efficient and economical monitoring of urban bird populations.

  20. A Testing System for Diagnosing Misconceptions in DC Electric Circuits.

    ERIC Educational Resources Information Center

    Chang, Kuo-En; Liu, Sei-Hua; Chen, Sei-Wang

    1998-01-01

    Outlines a test-based diagnosis system for misconceptions in DC electric circuits and its three parts: problem library, problem selector and diagnoser. Discusses misconception discrimination and diagnosis theories, and reports the system supports satisfactory diagnosis. Includes an analysis of nine student misconceptions about electrical circuits…

  1. Electrostatic coalescence system with independent AC and DC hydrophilic electrodes

    DOEpatents

    Hovarongkura, A. David; Henry, Jr., Joseph D.

    1981-01-01

    An improved electrostatic coalescence system is provided in which independent AC and DC hydrophilic electrodes are employed to provide more complete dehydration of an oil emulsion. The AC field is produced between an AC electrode array and the water-oil interface wherein the AC electrode array is positioned parallel to the interface which acts as a grounded electrode. The emulsion is introduced into the AC field in an evenly distributed manner at the interface. The AC field promotes drop-drop and drop-interface coalescence of the water phase in the entering emulsion. The continuous oil phase passes upward through the perforated AC electrode array and enters a strong DC field produced between closely spaced DC electrodes in which small dispersed droplets of water entrained in the continuous phase are removed primarily by collection at hydrophilic DC electrodes. Large droplets of water collected by the electrodes migrate downward through the AC electrode array to the interface. All phase separation mechanisms are utilized to accomplish more complete phase separation.

  2. 36 CFR 910.13 - Urban design of Washington, DC.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... CORPORATION GENERAL GUIDELINES AND UNIFORM STANDARDS FOR URBAN PLANNING AND DESIGN OF DEVELOPMENT WITHIN THE PENNSYLVANIA AVENUE DEVELOPMENT AREA Urban Planning and Design Concerns § 910.13 Urban design of Washington, DC... 36 Parks, Forests, and Public Property 3 2012-07-01 2012-07-01 false Urban design of...

  3. 36 CFR 910.13 - Urban design of Washington, DC.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... GENERAL GUIDELINES AND UNIFORM STANDARDS FOR URBAN PLANNING AND DESIGN OF DEVELOPMENT WITHIN THE PENNSYLVANIA AVENUE DEVELOPMENT AREA Urban Planning and Design Concerns § 910.13 Urban design of Washington, DC... 36 Parks, Forests, and Public Property 3 2013-07-01 2012-07-01 true Urban design of Washington,...

  4. 38 CFR 3.851 - St. Elizabeths Hospital, Washington, DC.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 38 Pensions, Bonuses, and Veterans' Relief 1 2011-07-01 2011-07-01 false St. Elizabeths Hospital, Washington, DC. 3.851 Section 3.851 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS AFFAIRS ADJUDICATION Pension, Compensation, and Dependency and Indemnity Compensation Incompetents, Guardianship and Institutional Awards § 3.851...

  5. Advanced dc motor controller for battery-powered electric vehicles

    NASA Technical Reports Server (NTRS)

    Belsterling, C. A.

    1981-01-01

    A motor generation set is connected to run from the dc source and generate a voltage in the traction motor armature circuit that normally opposes the source voltage. The functional feasibility of the concept is demonstrated with tests on a Proof of Principle System. An analog computer simulation is developed, validated with the results of the tests, applied to predict the performance of a full scale Functional Model dc Controller. The results indicate high efficiencies over wide operating ranges and exceptional recovery of regenerated energy. The new machine integrates both motor and generator on a single two bearing shaft. The control strategy produces a controlled bidirectional plus or minus 48 volts dc output from the generator permitting full control of a 96 volt dc traction motor from a 48 volt battery, was designed to control a 20 hp traction motor. The controller weighs 63.5 kg (140 lb.) and has a peak efficiency of 90% in random driving modes and 96% during the SAE J 227a/D driving cycle.

  6. 77 FR 14968 - Drawbridge Operation Regulation; Anacostia River, Washington, DC

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-03-14

    ..., Washington, DC in the Federal Register (76 FR 163). We did not receive public comments on the proposed rule... regulation that governs the operation of the CSX Railroad Vertical Lift Bridge across the Anacostia River... requested a change in the operation regulation for the CSX Railroad Vertical Lift Bridge, across...

  7. High-power ac/dc variable load simulator

    NASA Technical Reports Server (NTRS)

    Joncas, K. P.; Birnbach, S.; Bruce, L. D.; Smith, L.

    1975-01-01

    Design of medium-power dynamic electrical load simulator has been extended to permit simulation of ac as well as dc loads and to provide for operation at higher power levels. Simulator is internally protected against reverse voltage, overvoltage, overcurrent, and overload conditions.

  8. 76 FR 52602 - Drawbridge Operation Regulation; Anacostia River, Washington, DC

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-08-23

    ... public dockets in the January 17, 2008, issue of the Federal Register (73 FR 3316). Public Meeting We do... SECURITY Coast Guard 33 CFR Part 117 RIN 1625-AA09 Drawbridge Operation Regulation; Anacostia River... the Anacostia River, mile 3.4 at Washington, DC. The proposed change will alter the eight hour...

  9. 76 FR 52566 - Drawbridge Operation Regulations; Anacostia River, Washington, DC

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-08-23

    ... Federal Register (73 FR 3316). Public Meeting We do not now plan to hold a public meeting. But you may... SECURITY Coast Guard 33 CFR Part 117 Drawbridge Operation Regulations; Anacostia River, Washington, DC... governing the operation of the CSX Railroad Vertical Lift Bridge across the Anacostia River, mile 3.4,...

  10. Summary of electric vehicle dc motor-controller tests

    NASA Technical Reports Server (NTRS)

    Mcbrien, E. F.; Tryon, H. B.

    1982-01-01

    The differences in the performance of dc motors are evaluated when operating with chopper type controllers, and when operating on direct current. The interactions between the motor and the controller which cause these differences are investigated. Motor-controlled tests provided some of the data the quantified motor efficiency variations for both ripple free and chopper modes of operation.

  11. A High Efficiency DC Bus Regulator / RPC for Spacecraft Applications

    NASA Astrophysics Data System (ADS)

    Birchenough, Arthur G.

    2004-02-01

    DC bus voltage regulation may be required in future high powered spacecraft due to the length of the busses or because they are not generated at precise voltage levels. In these cases the regulation range is often only a few percent increase or decrease, but conventional DC voltage regulators switch all the power passing through them, and this level of power switched determines the size and losses in the regulator. A recently developed concept uses a low power DC-DC converter in series with the bus to raise or lower the bus voltage over a small range. This partial power processing technique combines the small size and power losses of the low power converter with the ability to regulate, (over a small range) a high power bus. The Series Connected Buck Boost Regulator (SCBBR) described herein provides bus regulation with an efficiency of 98%. The circuit also provides bus switching and overcurrent limiting functions of a Remote Power Controller (RPC). This paper describes the circuit design and performance of a breadboard SCBBR configured as a bus voltage regulator providing +/- 40% voltage regulation range, bus switching, and overload limiting.

  12. Controllable Bidirectional dc Power Sources For Large Loads

    NASA Technical Reports Server (NTRS)

    Tripp, John S.; Daniels, Taumi S.

    1995-01-01

    System redesigned for greater efficiency, durability, and controllability. Modern electronically controlled dc power sources proposed to supply currents to six electromagnets used to position aerodynamic test model in wind tunnel. Six-phase bridge rectifier supplies load with large current at voltage of commanded magnitude and polarity. Current-feedback circuit includes current-limiting feature giving some protection against overload.

  13. School Vouchers and Student Outcomes: Experimental Evidence from Washington, DC

    ERIC Educational Resources Information Center

    Wolf, Patrick J.; Kisida, Brian; Gutmann, Babette; Puma, Michael; Eissa, Nada; Rizzo, Lou

    2013-01-01

    School vouchers are the most contentious form of parental school choice. Vouchers provide government funds that parents can use to send their children to private schools of their choice. Here we examine the empirical question of whether or not a school voucher program in Washington, DC, affected achievement or the rate of high school graduation…

  14. HTS DC Transmission Line for Megalopolis Grid Development

    NASA Astrophysics Data System (ADS)

    Kopylov, S.; Sytnikov, V.; Bemert, S.; Ivanov, Yu; Krivetskiy, I.; Romashov, M.; Shakaryan, Yu; Keilin, V.; Shikov, A.; Patrikeev, V.; Lobyntsev, V.; Shcherbakov, V.

    2014-05-01

    Using of HTS AC and DC cables in electric power grids allows increasing of the transferred power, losses diminishing, decreasing of exclusion zone areas, the enhancement of the environmental conditions and fire/explosion safety of electric power systems. However, the use of DC superconducting cable lines together with converters brings additional advantages as reduction of losses in cables and suitable lowering of refrigerating plant capacity, as well as the realization of the function of short-circuit currents limitation by means of the appropriate setting of converter equipment. Russian Federal Grid Company and its R&D Center started the construction of the DC HTS power transmission line which includes the cable itself, cryogenic equipment, AC/DC converters, terminals and cable coupling boxes. This line will connect two substations in Saint-Petersburg - 330 kV "Centralnaya" and 220 kV "RP-9". The length of this HTS transmission line will be about 2500 meters. Nowadays are developed all the elements of the line and technologies of the cable manufacturing. Two HTS cable samples, each 30 m length, have been made. This paper describes the results of cables tests.

  15. Plant Generator driven by a small Delco 32 volt DC ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Plant Generator driven by a small Delco 32 volt DC steam engine with a maximum output of 17.6 kilowatts - East Broad Top Railroad & Coal Company, Machine Shop, State Route 994, West of U.S. Route 522, Rockhill Furnace, Huntingdon County, PA

  16. Parks, Trees, and Environmental Justice: Field Notes from Washington, DC

    ERIC Educational Resources Information Center

    Buckley, Geoffrey L.; Whitmer, Ali; Grove, J. Morgan

    2013-01-01

    Students enrolled in a graduate seminar benefited in multiple ways from an intensive 3-day field trip to Washington, DC. Constructed around the theme of environmental justice, the trip gave students a chance to learn about street tree distribution, park quality, and racial segregation "up close." Working with personnel from the United…

  17. Transcriptional IL-15-Directed in vivo DC Targeting DNA Vaccine

    PubMed Central

    Tian, S; Liu, Z; Donahue, C; Noh, HS; Falo, LD; You, Z

    2009-01-01

    DC engineered in vitro by DNA encoding OVAhsp70 and IL-15 up-regulated their expressions of CD80, CD86, CCR7 and IL-15Rα and promoted their productions of IL-6, IL-12 and TNF-α. Transcriptional IL-15-directed in vivo DC targeting DNA vaccine encoding OVAhsp70 elicited long-lasting Th1 and CTL responses and anti-B16OVA activity. CD8 T cell-mediated primary tumor protection was abrogated by DC or CD4 T cell depletion during the induction phase of immune responses. However, CD4 T cell depletion during immunization did not impair CD8 T cell-dependent long-lasting tumor protection. Furthermore, in vivo DC-derived IL-15 exerted the enhancements of cellular and humoral immune responses and antitumor immunity elicited by OVAhsp70 DNA vaccine. Importantly, the potency of this novel DNA vaccine strategy was proven using a self/tumor Ag (TRP2) in a clinically relevant B16 melanoma model. These findings have implications for developing next generation DNA vaccines against cancers and infectious diseases in both healthy and CD4 deficient individuals. PMID:19727134

  18. Washington, D.C.: A Very Great Place to Visit.

    ERIC Educational Resources Information Center

    Camping Magazine, 1986

    1986-01-01

    Describes places of interest in Washington, D.C. for attendees of the Second International Camping Congress on March 2-6, 1987. Includes information about the Capitol, Air and Space Museum, National Museum of Natural History, National Museum of American History, Washington Monument, Lincoln Memorial, and White House. Contains photographs of four…

  19. Brushless dc motors. [applications in non-space technology

    NASA Technical Reports Server (NTRS)

    1975-01-01

    Brushless dc motors were intensively developed and tested over several years before qualification as the prime movers for Apollo Spacecraft life support blowers, and for circulating oxygen in the lunar portable life support system. Knowledge gained through prototype development and critical testing has significantly influenced the technology employed, broadened markets and applications, and reduced the cost of present day motors.

  20. Plasmacytoid DC from aged mice down-regulate CD8 T cell responses by inhibiting cDC maturation after Encephalitozoon cuniculi infection.

    PubMed

    Gigley, Jason P; Khan, Imtiaz A

    2011-01-01

    Age associated impairment of immune function results in inefficient vaccination, tumor surveillance and increased severity of infections. Several alterations in adaptive immunity have been observed and recent studies report age related declines in innate immune responses to opportunistic pathogens including Encephalitozoon cuniculi. We previously demonstrated that conventional dendritic cells (cDC) from 9-month-old animals exhibit sub-optimal response to E. cuniculi infection, suggesting that age associated immune senescence begins earlier than expected. We focused this study on how age affects plasmacytoid DC (pDC) function. More specifically how aged pDC affect cDC function as we observed that the latter are the predominant activators of CD8 T cells during this infection. Our present study demonstrates that pDC from middle-aged mice (12 months) suppress young (8 week old) cDC driven CD8 T cell priming against E. cuniculi infection. The suppressive effect of pDC from older mice decreased maturation of young cDC via cell contact. Aged mouse pDC exhibited higher expression of PD-L1 and blockade of their interaction with cDC via this molecule restored cDC maturation and T cell priming. Furthermore, the PD-L1 dependent suppression of cDC T cell priming was restricted to effector function of antigen-specific CD8 T cells not their expansion. To the best of our knowledge, the data presented here is the first report highlighting a cell contact dependent, PD-L1 regulated, age associated defect in a DC subpopulation that results in a sub-optimal immune response against E. cuniculi infection. These results have broad implications for design of immunotherapeutic approaches to enhance immunity for aging populations.

  1. Recovery Act: Integrated DC-DC Conversion for Energy-Efficient Multicore Processors

    SciTech Connect

    Shepard, Kenneth L

    2013-03-31

    In this project, we have developed the use of thin-film magnetic materials to improve in energy efficiency of digital computing applications by enabling integrated dc-dc power conversion and management with on-chip power inductors. Integrated voltage regulators also enables fine-grained power management, by providing dynamic scaling of the supply voltage in concert with the clock frequency of synchronous logic to throttle power consumption at periods of low computational demand. The voltage converter generates lower output voltages during periods of low computational performance requirements and higher output voltages during periods of high computational performance requirements. Implementation of integrated power conversion requires high-capacity energy storage devices, which are generally not available in traditional semiconductor processes. We achieve this with integration of thin-film magnetic materials into a conventional complementary metal-oxide-semiconductor (CMOS) process for high-quality on-chip power inductors. This project includes a body of work conducted to develop integrated switch-mode voltage regulators with thin-film magnetic power inductors. Soft-magnetic materials and inductor topologies are selected and optimized, with intent to maximize efficiency and current density of the integrated regulators. A custom integrated circuit (IC) is designed and fabricated in 45-nm CMOS silicon-on-insulator (SOI) to provide the control system and power-train necessary to drive the power inductors, in addition to providing a digital load for the converter. A silicon interposer is designed and fabricated in collaboration with IBM Research to integrate custom power inductors by chip stacking with the 45-nm CMOS integrated circuit, enabling power conversion with current density greater than 10A/mm2. The concepts and designs developed from this work enable significant improvements in performance-per-watt of future microprocessors in servers, desktops, and mobile

  2. Baseline and Lifetime Assessments for DC745U Elastomeric Components

    SciTech Connect

    Maxwell, R S; Chinn, S C; Herberg, J; Harvey, C; Alviso, C; Vance, A; Cohenour, R; Wilson, M; Solyom, D

    2004-12-20

    The silicone elastomer Dow Corning DC 745U is used in two major components in the W80. We have investigated a number of issues concerning this material. Our studies have accomplished a baseline study of the chemical composition of DC745 and LLNL now has a good understanding of the chemical composition of this material. DC745 crystallizes within the system STS. Two potential means identified to mitigate the risk associated with this phenomenon are to (1) change material formulation and (2) predose the parts to {approx} 25 MRad {gamma}-radiation. A candidate material identified by Gordon Spellman has been studied for composition and the lack of crystallization within the STS has been verified. A sensitivity study of the effects of relevant aging mechanisms also has been performed. The extent of aging due to radiation exposure or elevated temperatures is minimal over the expected course of the LEP. In addition, since the DC745 parts are expected to be replaced at rebuild, the aging clock is essentially being reset. No significant aging issues seem likely to develop for these parts. DC745 parts are also subject to permanent deformation in service. Our studies have shown that the deformation is likely due to incomplete mixing of the raw gum stock and the curing agent at production. This results in areas of low crosslink density that are subject to a higher degree of compression set in service. We have identified two production diagnostic tools based on Nuclear Magnetic Resonance spectroscopy to prescreen the parts at production at KCP. These studies are concluded with specific recommendation for changes to core surveillance for this part based on the chemical knowledge we have gained from this study.

  3. Vegetation studies, National Training Center, Fort Irwin, California

    SciTech Connect

    Brandt, C.A.; Rickard, W.H.; Cadoret, N.A.

    1997-09-01

    During the spring of 1992, the Pacific Northwest National Laboratory (PNNL) conducted surveys of the Avawatz and Granite mountains springs for the National Training Center (NTC) to evaluate the occurrence of sensitive plant species in these areas. PNNL also conducted a survey of the eastern outwash of the Paradise Range for the occurrence of Lane Mountain milk vetch (Astragalus jaegerianus). In spring of 1993, PNNL conducted an additional study of Lane Mountain milk vetch on the NTC to determine habitat characteristics for this plant and to develop a method for predicting its potential occurrence, based on simple habitat attributes. The results of these studies are itemized.

  4. Reliability and performance studies of DC-DC conversion powering scheme for the CMS pixel tracker at SLHC

    NASA Astrophysics Data System (ADS)

    Todri, A.; Perera, L.; Rivera, R.; Kwan, S.

    2010-12-01

    The upgrades of the Large Hadron Collider (LHC) introduce a significant challenge to the power distribution of the detectors. DC-DC conversion is the preferred powering scheme proposed to be integrated for the CMS tracker to deliver high input voltage levels and performing a step-down conversion nearby the detector modules. In this work, we propose a step-up/step-down powering scheme by performing voltage step up at the CAEN supply unit and voltage step down near the detector. We designed step-up converters and investigate the pixel performance and power loss on the FPIX power distribution system. Tests are performed using the PSI46 pixel readout chips on a forward pixel panel module and the DC-DC converters developed at CERN and Fermilab. Reliability studies include the voltage drop measurements on the readout chips and the power supply noise generated from the converter. Performance studies include pixel noise and threshold dispersion results. Comparison between step-down only and step-up/step-down conversion powering schemes are provided.

  5. Effect of DC/mDC iontophoresis and terpenes on transdermal permeation of methotrexate: in vitro study.

    PubMed

    Prasad, R; Koul, V; Anand, S; Khar, R K

    2007-03-21

    The systemic toxicity caused by methotrexate limits its use and transdermal delivery would be a possible alternative. Transdermal permeation of methotrexate loaded into polyacrylamide-based hydrogel patch, across mice skin was studied in vitro after pretreatment with terpenes and ethanol, alone or in combination with iontophoresis (DC/mDC). Polyacrylamide patches gave the maximum flux as compared to the copolymers of acrylamide and acrylic acid. Of the terpenes used, pure menthol showed maximum enhancement (38%), whereas pure limonene elicited a minimum of 9.9% enhancement. Binary combination of menthol and ethanol increased the permeation to 54.9%, which was further enhanced to 93.69% and 117% when used in combination with DC and square wave (mDC) iontophoresis, respectively. ATR-FTIR of the stratum corneum treated with terpenes showed a split in the asymmetric C-H stretching vibrations along with decrease in peak heights and areas of asymmetric, symmetric C-H stretching, C=O stretching and amide bands. A split in amide II band was observed with iontophoresis. ATR-FTIR studies suggest conformational changes in the lipid-protein domains thereby increasing permeation. Histopathological studies on treated skin samples, gave an insight about the anatomical changes brought by the application of various enhancers. Binary mixture of menthol and ethanol in combination with square wave gave best results.

  6. Multiple-DC-Inputs Direct Electric Power Converter D-EPC with DC Power Sources Connected in Series

    NASA Astrophysics Data System (ADS)

    Yoshimoto, Kantaro; Satou, Shou; Maikawa, Kengo; Takahashi, Kouji

    A series-type multiple-dc-inputs direct electric power converter (D-EPC) has been developed. The D-EPC is a multiple-dc-inputs inverter, and it can eliminate the need for a dc/dc converter that is generally used in conventional converter/inverter systems. The original D-EPC has two positive terminals and a negative terminal in common. Each upper arm between the positive terminal and the ac output is built with a bidirectional switch to prevent short circuit. In the series-type D-EPC, the input power sources are connected in series, thus, the number of bidirectional switches can be reduced and the series voltage can be used in the motor drive system. A new pulse width modulation (PWM) generation technique to drive switching devices in the series-type D-EPC has also been developed. Tests have confirmed that the motor can be operated by controlling the power distribution and that a series voltage can be used.

  7. Effect of DC/mDC iontophoresis and terpenes on transdermal permeation of methotrexate: in vitro study.

    PubMed

    Prasad, R; Koul, V; Anand, S; Khar, R K

    2007-03-21

    The systemic toxicity caused by methotrexate limits its use and transdermal delivery would be a possible alternative. Transdermal permeation of methotrexate loaded into polyacrylamide-based hydrogel patch, across mice skin was studied in vitro after pretreatment with terpenes and ethanol, alone or in combination with iontophoresis (DC/mDC). Polyacrylamide patches gave the maximum flux as compared to the copolymers of acrylamide and acrylic acid. Of the terpenes used, pure menthol showed maximum enhancement (38%), whereas pure limonene elicited a minimum of 9.9% enhancement. Binary combination of menthol and ethanol increased the permeation to 54.9%, which was further enhanced to 93.69% and 117% when used in combination with DC and square wave (mDC) iontophoresis, respectively. ATR-FTIR of the stratum corneum treated with terpenes showed a split in the asymmetric C-H stretching vibrations along with decrease in peak heights and areas of asymmetric, symmetric C-H stretching, C=O stretching and amide bands. A split in amide II band was observed with iontophoresis. ATR-FTIR studies suggest conformational changes in the lipid-protein domains thereby increasing permeation. Histopathological studies on treated skin samples, gave an insight about the anatomical changes brought by the application of various enhancers. Binary mixture of menthol and ethanol in combination with square wave gave best results. PMID:17116378

  8. 77 FR 69812 - Agency Information Collection Activities; Comment Request; DC Choice Evaluation

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-11-21

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF EDUCATION Agency Information Collection Activities; Comment Request; DC Choice Evaluation AGENCY: Institute of... of Collection: DC Choice Evaluation. OMB Control Number: Pending. Type of Review: New...

  9. 21 CFR 74.1330 - D&C Red No. 30.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... ADDITIVES SUBJECT TO CERTIFICATION Drugs § 74.1330 D&C Red No. 30. (a) Identity. (1) The color additive D&C... thiophen-3(2H)-one (CAS Reg. No. 2379-74-0). (2) Color additive mixtures for drug use made with D&C Red No... as safe for use in color additive mixtures for coloring drugs. (b) Specifications. D&C Red No....

  10. 21 CFR 74.1330 - D&C Red No. 30.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... ADDITIVES SUBJECT TO CERTIFICATION Drugs § 74.1330 D&C Red No. 30. (a) Identity. (1) The color additive D&C... thiophen-3(2H)-one (CAS Reg. No. 2379-74-0). (2) Color additive mixtures for drug use made with D&C Red No... as safe for use in color additive mixtures for coloring drugs. (b) Specifications. D&C Red No....

  11. 21 CFR 82.2707a - Ext. D&C Yellow No. 7.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Ext. D&C Yellow No. 7. 82.2707a Section 82.2707a... Ext. D&C Yellow No. 7. The color additive Ext. D&C Yellow No. 7 shall conform in identity with specifications to the requirements of § 74.1707a(a)(1) and (b) of this chapter. Ext. D&C Yellow No. 7...

  12. A Theory of Control for a Class of Electronic Power Processing Systems: Energy-Storage DC-To-DC Converters. Ph.D. Thesis

    NASA Technical Reports Server (NTRS)

    Burns, W. W., III

    1977-01-01

    An analytically derived approach to the control of energy-storage dc-to-dc converters, which enables improved system performance and an extensive understanding of the manner in which this improved performance is accomplished, is presented. The control approach is derived from a state-plane analysis of dc-to-dc converter power stages which enables a graphical visualization of the movement of the system state during both steady state and transient operation. This graphical representation of the behavior of dc-to-dc converter systems yields considerable qualitative insight into the cause and effect relationships which exist between various commonly used converter control functions and the system performance which results from them.

  13. 21 CFR 74.2322 - D&C Red No. 22.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... ADDITIVES SUBJECT TO CERTIFICATION Cosmetics § 74.2322 D&C Red No. 22. (a) Identity and specifications. The color additive D&C Red No. 22 shall conform in identity and specifications to the requirements of § 74.1322(a)(1) and (b). (b) Uses and restrictions. The color additive D&C Red No. 22 may be safely used...

  14. 21 CFR 74.2710 - D&C Yellow No. 10.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... COLOR ADDITIVES SUBJECT TO CERTIFICATION Cosmetics § 74.2710 D&C Yellow No. 10. (a) Identity and specifications. The color additive D&C Yellow No. 10 shall conform in identity and specifications to the requirements of § 74.1710(a)(1) and (b). (b) Uses and restrictions. The color additive D&C Yellow No. 10 may...

  15. 21 CFR 74.2307 - D&C Red No. 7

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... ADDITIVES SUBJECT TO CERTIFICATION Cosmetics § 74.2307 D&C Red No. 7 (a) Identity and specifications. The color additive D&C Red No. 7 shall conform in identity and specifications to the requirements of § 74.1307 (a)(1) and (b). (b) Uses and restrictions. The color additive D&C Red No. 7 may be safely used...

  16. 21 CFR 74.1336 - D&C Red No. 36.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... ADDITIVES SUBJECT TO CERTIFICATION Drugs § 74.1336 D&C Red No. 36. (a) Identity. (1) The color additive D&C Red No. 36 is 1- -2-naphthalenol (CAS Reg. No. 2814-77-9). The color additive is manufactured by...) Color additive mixtures for drug use made with D&C Red No. 36 may contain only those diluents that...

  17. 21 CFR 74.2307 - D&C Red No. 7

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... ADDITIVES SUBJECT TO CERTIFICATION Cosmetics § 74.2307 D&C Red No. 7 (a) Identity and specifications. The color additive D&C Red No. 7 shall conform in identity and specifications to the requirements of § 74.1307 (a)(1) and (b). (b) Uses and restrictions. The color additive D&C Red No. 7 may be safely used...

  18. 21 CFR 74.2710 - D&C Yellow No. 10.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... COLOR ADDITIVES SUBJECT TO CERTIFICATION Cosmetics § 74.2710 D&C Yellow No. 10. (a) Identity and specifications. The color additive D&C Yellow No. 10 shall conform in identity and specifications to the requirements of § 74.1710(a)(1) and (b). (b) Uses and restrictions. The color additive D&C Yellow No. 10 may...

  19. 21 CFR 74.2307 - D&C Red No. 7

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... ADDITIVES SUBJECT TO CERTIFICATION Cosmetics § 74.2307 D&C Red No. 7 (a) Identity and specifications. The color additive D&C Red No. 7 shall conform in identity and specifications to the requirements of § 74.1307 (a)(1) and (b). (b) Uses and restrictions. The color additive D&C Red No. 7 may be safely used...

  20. 21 CFR 74.2321 - D&C Red No. 21.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... ADDITIVES SUBJECT TO CERTIFICATION Cosmetics § 74.2321 D&C Red No. 21. (a) Identity and specifications. The color additive D&C Red No. 21 shall conform in identity and specifications to the requirements of § 74.1321(a)(1) and (b). (b) Uses and restrictions. The color additive D&C Red No. 21 may be safely used...

  1. 21 CFR 74.1206 - D&C Green No. 6.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... consistent with current good manufacturing practice. (d) Labeling. The label of the color additive shall... ADDITIVES SUBJECT TO CERTIFICATION Drugs § 74.1206 D&C Green No. 6. (a) Identity. The color additive D&C... additive D&C Green No. 6 for use in coloring externally applied drugs shall conform to the...

  2. 21 CFR 74.1336 - D&C Red No. 36.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... ADDITIVES SUBJECT TO CERTIFICATION Drugs § 74.1336 D&C Red No. 36. (a) Identity. (1) The color additive D&C Red No. 36 is 1- -2-naphthalenol (CAS Reg. No. 2814-77-9). The color additive is manufactured by...) Color additive mixtures for drug use made with D&C Red No. 36 may contain only those diluents that...

  3. 21 CFR 74.2322 - D&C Red No. 22.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... ADDITIVES SUBJECT TO CERTIFICATION Cosmetics § 74.2322 D&C Red No. 22. (a) Identity and specifications. The color additive D&C Red No. 22 shall conform in identity and specifications to the requirements of § 74.1322(a)(1) and (b). (b) Uses and restrictions. The color additive D&C Red No. 22 may be safely used...

  4. 21 CFR 74.2321 - D&C Red No. 21.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... ADDITIVES SUBJECT TO CERTIFICATION Cosmetics § 74.2321 D&C Red No. 21. (a) Identity and specifications. The color additive D&C Red No. 21 shall conform in identity and specifications to the requirements of § 74.1321(a)(1) and (b). (b) Uses and restrictions. The color additive D&C Red No. 21 may be safely used...

  5. 21 CFR 74.2322 - D&C Red No. 22.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... ADDITIVES SUBJECT TO CERTIFICATION Cosmetics § 74.2322 D&C Red No. 22. (a) Identity and specifications. The color additive D&C Red No. 22 shall conform in identity and specifications to the requirements of § 74.1322(a)(1) and (b). (b) Uses and restrictions. The color additive D&C Red No. 22 may be safely used...

  6. 21 CFR 74.2306 - D&C Red No. 6.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... ADDITIVES SUBJECT TO CERTIFICATION Cosmetics § 74.2306 D&C Red No. 6. (a) Identity and specifications.The color additive D&C Red No. 6 shall conform in identity and specifications to the requirements of § 74.1306 (a)(1) and (b). (b) Uses and restrictions. The color additive D&C Red No. 6 may be safely used...

  7. 21 CFR 74.1206 - D&C Green No. 6.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... consistent with current good manufacturing practice. (d) Labeling. The label of the color additive shall... ADDITIVES SUBJECT TO CERTIFICATION Drugs § 74.1206 D&C Green No. 6. (a) Identity. The color additive D&C... additive D&C Green No. 6 for use in coloring externally applied drugs shall conform to the...

  8. 21 CFR 74.2321 - D&C Red No. 21.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... ADDITIVES SUBJECT TO CERTIFICATION Cosmetics § 74.2321 D&C Red No. 21. (a) Identity and specifications. The color additive D&C Red No. 21 shall conform in identity and specifications to the requirements of § 74.1321(a)(1) and (b). (b) Uses and restrictions. The color additive D&C Red No. 21 may be safely used...

  9. 21 CFR 74.1331 - D&C Red No. 31.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... amounts consistent with good manufacturing practice. (d) Labeling. The label of the color additive and any... ADDITIVES SUBJECT TO CERTIFICATION Drugs § 74.1331 D&C Red No. 31. (a) Identity. (1) The color additive D&C...) Color additive mixtures for drug use made with D&C Red No. 31 may contain only those diluents that...

  10. 21 CFR 74.2307 - D&C Red No. 7

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... ADDITIVES SUBJECT TO CERTIFICATION Cosmetics § 74.2307 D&C Red No. 7 (a) Identity and specifications. The color additive D&C Red No. 7 shall conform in identity and specifications to the requirements of § 74.1307 (a)(1) and (b). (b) Uses and restrictions. The color additive D&C Red No. 7 may be safely used...

  11. 21 CFR 74.2322 - D&C Red No. 22.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... ADDITIVES SUBJECT TO CERTIFICATION Cosmetics § 74.2322 D&C Red No. 22. (a) Identity and specifications. The color additive D&C Red No. 22 shall conform in identity and specifications to the requirements of § 74.1322(a)(1) and (b). (b) Uses and restrictions. The color additive D&C Red No. 22 may be safely used...

  12. 21 CFR 74.1336 - D&C Red No. 36.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... ADDITIVES SUBJECT TO CERTIFICATION Drugs § 74.1336 D&C Red No. 36. (a) Identity. (1) The color additive D&C Red No. 36 is 1- -2-naphthalenol (CAS Reg. No. 2814-77-9). The color additive is manufactured by...) Color additive mixtures for drug use made with D&C Red No. 36 may contain only those diluents that...

  13. 21 CFR 74.2306 - D&C Red No. 6.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... ADDITIVES SUBJECT TO CERTIFICATION Cosmetics § 74.2306 D&C Red No. 6. (a) Identity and specifications.The color additive D&C Red No. 6 shall conform in identity and specifications to the requirements of § 74.1306 (a)(1) and (b). (b) Uses and restrictions. The color additive D&C Red No. 6 may be safely used...

  14. 21 CFR 74.2321 - D&C Red No. 21.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... ADDITIVES SUBJECT TO CERTIFICATION Cosmetics § 74.2321 D&C Red No. 21. (a) Identity and specifications. The color additive D&C Red No. 21 shall conform in identity and specifications to the requirements of § 74.1321(a)(1) and (b). (b) Uses and restrictions. The color additive D&C Red No. 21 may be safely used...

  15. 21 CFR 74.2710 - D&C Yellow No. 10.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... COLOR ADDITIVES SUBJECT TO CERTIFICATION Cosmetics § 74.2710 D&C Yellow No. 10. (a) Identity and specifications. The color additive D&C Yellow No. 10 shall conform in identity and specifications to the requirements of § 74.1710(a)(1) and (b). (b) Uses and restrictions. The color additive D&C Yellow No. 10 may...

  16. 21 CFR 74.2306 - D&C Red No. 6.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... ADDITIVES SUBJECT TO CERTIFICATION Cosmetics § 74.2306 D&C Red No. 6. (a) Identity and specifications.The color additive D&C Red No. 6 shall conform in identity and specifications to the requirements of § 74.1306 (a)(1) and (b). (b) Uses and restrictions. The color additive D&C Red No. 6 may be safely used...

  17. 21 CFR 74.2710 - D&C Yellow No. 10.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... COLOR ADDITIVES SUBJECT TO CERTIFICATION Cosmetics § 74.2710 D&C Yellow No. 10. (a) Identity and specifications. The color additive D&C Yellow No. 10 shall conform in identity and specifications to the requirements of § 74.1710(a)(1) and (b). (b) Uses and restrictions. The color additive D&C Yellow No. 10 may...

  18. 21 CFR 74.2306 - D&C Red No. 6.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... ADDITIVES SUBJECT TO CERTIFICATION Cosmetics § 74.2306 D&C Red No. 6. (a) Identity and specifications.The color additive D&C Red No. 6 shall conform in identity and specifications to the requirements of § 74.1306 (a)(1) and (b). (b) Uses and restrictions. The color additive D&C Red No. 6 may be safely used...

  19. 21 CFR 74.2710 - D&C Yellow No. 10.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... COLOR ADDITIVES SUBJECT TO CERTIFICATION Cosmetics § 74.2710 D&C Yellow No. 10. (a) Identity and specifications. The color additive D&C Yellow No. 10 shall conform in identity and specifications to the requirements of § 74.1710(a)(1) and (b). (b) Uses and restrictions. The color additive D&C Yellow No. 10 may...

  20. 21 CFR 74.2052 - D&C Black No. 2.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL LISTING OF COLOR ADDITIVES SUBJECT TO CERTIFICATION Cosmetics § 74.2052 D&C Black No. 2. (a) Identity. The color additive D&C... color (as carbon), not less than 95 percent. (c) Uses and restrictions. D&C Black No. 2 may be...

  1. DC66812 AERIAL VIEW OF THE 14TH AND 15TH STREET CORRIDORS, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    DC-668-12 AERIAL VIEW OF THE 14TH AND 15TH STREET CORRIDORS, LOOKING NORTH FROM ABOVE EAST POTOMAC PARK TOWARD THE MALL AND BEYOND - L'Enfant-McMillan Plan of Washington, DC, Washington, District of Columbia, DC

  2. DC6683 AERIAL VIEW LOOKING SOUTHWEST INTO THE CITY FROM THE ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    DC-668-3 AERIAL VIEW LOOKING SOUTHWEST INTO THE CITY FROM THE BEND IN NORTH CAPITOL STREET IN THE MICHIGAN AVENUE VICINITY (Photograph has been enlarged from a 4x5 negative) - L'Enfant-McMillan Plan of Washington, DC, Washington, District of Columbia, DC

  3. DC66821 VIEW NORTHWEST TOWARD RESERVATION NO. 715 AND THE E ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    DC-668-21 VIEW NORTHWEST TOWARD RESERVATION NO. 715 AND THE E STREET EXPRESSWAY ENTRY AT 19TH AND E STREETS, NW FROM THE ROOF OF THE DEPARTMENT OF THE INTERIOR. - L'Enfant-McMillan Plan of Washington, DC, Washington, District of Columbia, DC

  4. 14 CFR 93.337 - Requirements for operating in the DC SFRA.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... TRANSPORTATION (CONTINUED) AIR TRAFFIC AND GENERAL OPERATING RULES SPECIAL AIR TRAFFIC RULES Washington, DC Metropolitan Area Special Flight Rules Area § 93.337 Requirements for operating in the DC SFRA. A pilot... 14 Aeronautics and Space 2 2012-01-01 2012-01-01 false Requirements for operating in the DC...

  5. 14 CFR 93.337 - Requirements for operating in the DC SFRA.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... TRANSPORTATION (CONTINUED) AIR TRAFFIC AND GENERAL OPERATING RULES SPECIAL AIR TRAFFIC RULES Washington, DC Metropolitan Area Special Flight Rules Area § 93.337 Requirements for operating in the DC SFRA. A pilot... 14 Aeronautics and Space 2 2010-01-01 2010-01-01 false Requirements for operating in the DC...

  6. 36 CFR 1280.60 - Where do I enter the National Archives Building in Washington, DC?

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... Archives Building in Washington, DC? 1280.60 Section 1280.60 Parks, Forests, and Public Property NATIONAL... for Using NARA Facilities in the Washington, DC, Area? § 1280.60 Where do I enter the National Archives Building in Washington, DC? (a) To conduct research or official business, you must enter...

  7. DC6682 AERIAL VIEW LOOKING SOUTH DOWN THE NORTH CAPITOL STREET ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    DC-668-2 AERIAL VIEW LOOKING SOUTH DOWN THE NORTH CAPITOL STREET CORRIDOR FROM ABOVE THE MICHIGAN AVENUE VICINITY (Photograph has been enlarged from a 4x5 negative)ING NORTH ALONG SIXTEENTH STREET - L'Enfant-McMillan Plan of Washington, DC, Washington, District of Columbia, DC

  8. 14 CFR 93.337 - Requirements for operating in the DC SFRA.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... TRANSPORTATION (CONTINUED) AIR TRAFFIC AND GENERAL OPERATING RULES SPECIAL AIR TRAFFIC RULES Washington, DC Metropolitan Area Special Flight Rules Area § 93.337 Requirements for operating in the DC SFRA. A pilot... 14 Aeronautics and Space 2 2014-01-01 2014-01-01 false Requirements for operating in the DC...

  9. DC6681 AERIAL VIEW LOOKING SOUTHEAST DOWN THE MOUNT PLEASANT AND ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    DC-668-1 AERIAL VIEW LOOKING SOUTHEAST DOWN THE MOUNT PLEASANT AND 17TH STREET CORRIDORS (Photograph has been enlarged from a 4x5 negative) - L'Enfant-McMillan Plan of Washington, DC, Washington, District of Columbia, DC

  10. DC6687 AERIAL VIEW OF THE SOUTHEAST QUADRANT, LOOKING NORTHWEST FROM ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    DC-668-7 AERIAL VIEW OF THE SOUTHEAST QUADRANT, LOOKING NORTHWEST FROM ABOVE THE ANACOSTIA RIVER (Photograph has been enlarged from a 4x5 negative) - L'Enfant-McMillan Plan of Washington, DC, Washington, District of Columbia, DC

  11. 36 CFR 1280.60 - Where do I enter the National Archives Building in Washington, DC?

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Archives Building in Washington, DC? 1280.60 Section 1280.60 Parks, Forests, and Public Property NATIONAL... for Using NARA Facilities in the Washington, DC, Area? § 1280.60 Where do I enter the National Archives Building in Washington, DC? (a) To conduct research or official business, you must enter...

  12. DC66841 VIEW NORTH ON THE TENTH STREET PROMENADE SHOWING THE ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    DC-668-41 VIEW NORTH ON THE TENTH STREET PROMENADE SHOWING THE DEPARTMENT OF ENERGY BUILDING BLOCKING THE VISTA TO THE SMITHSONIAN CASTLE WITH THE BANNEKER CIRCLE (RESERVATION NO. 719) FOUNTAIN IN THE FOREGROUND - L'Enfant-McMillan Plan of Washington, DC, Washington, District of Columbia, DC

  13. 36 CFR 1280.60 - Where do I enter the National Archives Building in Washington, DC?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Archives Building in Washington, DC? 1280.60 Section 1280.60 Parks, Forests, and Public Property NATIONAL... for Using NARA Facilities in the Washington, DC, Area? § 1280.60 Where do I enter the National Archives Building in Washington, DC? (a) To conduct research or official business, you must enter...

  14. 76 FR 51255 - Security Zone; Potomac River, Georgetown Channel, Washington, DC

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-08-18

    ..., Washington, DC AGENCY: Coast Guard, DHS. ACTION: Temporary final rule. SUMMARY: The Coast Guard is... Washington, DC, in order to safeguard high-ranking public officials from terrorist acts and incidents. This... Avenue, SE., Washington, DC 20590, between 9 a.m. and 5 p.m., Monday through Friday, except...

  15. 14 CFR 93.337 - Requirements for operating in the DC SFRA.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... TRANSPORTATION (CONTINUED) AIR TRAFFIC AND GENERAL OPERATING RULES SPECIAL AIR TRAFFIC RULES Washington, DC Metropolitan Area Special Flight Rules Area § 93.337 Requirements for operating in the DC SFRA. A pilot... 14 Aeronautics and Space 2 2011-01-01 2011-01-01 false Requirements for operating in the DC...

  16. DC6685 AERIAL VIEW LOOKING SOUTHWEST INTO THE CITY TOWARD THE ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    DC-668-5 AERIAL VIEW LOOKING SOUTHWEST INTO THE CITY TOWARD THE ROBERT F. KENNEDY STADIUM FROM ABOVE THE EAST SHORE OF THE ANACOSTIA RIVER (Photograph has been enlarged from a 4x5 negative) - L'Enfant-McMillan Plan of Washington, DC, Washington, District of Columbia, DC

  17. DC66822 VIEW SOUTH TOWARD VIRGINIA AVENUE AND TO WEST POTOMAC ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    DC-668-22 VIEW SOUTH TOWARD VIRGINIA AVENUE AND TO WEST POTOMAC PARK BEYOND FROM THE ROOF OF THE DEPARTMENT OF THE INTERIOR AT 19TH AND C STREETS, NW - L'Enfant-McMillan Plan of Washington, DC, Washington, District of Columbia, DC

  18. 14 CFR 93.337 - Requirements for operating in the DC SFRA.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... TRANSPORTATION (CONTINUED) AIR TRAFFIC AND GENERAL OPERATING RULES SPECIAL AIR TRAFFIC RULES Washington, DC Metropolitan Area Special Flight Rules Area § 93.337 Requirements for operating in the DC SFRA. A pilot... 14 Aeronautics and Space 2 2013-01-01 2013-01-01 false Requirements for operating in the DC...

  19. 36 CFR 1280.60 - Where do I enter the National Archives Building in Washington, DC?

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Archives Building in Washington, DC? 1280.60 Section 1280.60 Parks, Forests, and Public Property NATIONAL... for Using NARA Facilities in the Washington, DC, Area? § 1280.60 Where do I enter the National Archives Building in Washington, DC? (a) To conduct research or official business, you must enter...

  20. Spreading Freedom and Saving Money. The Fiscal Impact of the D.C. Voucher Program

    ERIC Educational Resources Information Center

    Aud, Susan L.; Michos, Leon

    2006-01-01

    In August 2004 the first ever federally funded school voucher program began in Washington, D.C. Eligible students could attend a private school of their choice in the District of Columbia. Each participant received up to $7,500 for school tuition, fees, and transportation. In addition, the D.C. Public School System (DCPS) and D.C. charter school…