Missile Defense in the 21st Century Acquisition Environment: Exploring a BMD-Capable LCS Mission Package

DTIC Science & Technology

2013-09-01

75 Figure 25: Swing Weight Analysis....................................................................................76 Figure 26...AN/SPY-1D radar “can track golf ball-sized targets at ranges in excess of 165 kilometers” (Robinson, 2004). Given the radar cross section (RCS) of a... golf ball (calculated as a simple metallic sphere), it was determined that this would correspond to a maximum detection range beyond the Launch

Effects of elastic bed on hydrodynamic forces for a submerged sphere in an ocean of finite depth

NASA Astrophysics Data System (ADS)

Mohapatra, Smrutiranjan

2017-08-01

In this paper, we consider a hydroelastic model to examine the radiation of waves by a submerged sphere for both heave and sway motions in a single-layer fluid flowing over an infinitely extended elastic bottom surface in an ocean of finite depth. The elastic bottom is modeled as a thin elastic plate and is based on the Euler-Bernoulli beam equation. The effect of the presence of surface tension at the free-surface is neglected. In such situation, there exist two modes of time-harmonic waves: the one with a lower wavenumber (surface mode) propagates along the free-surface and the other with higher wavenumber (flexural mode) propagates along the elastic bottom surface. Based on the small amplitude wave theory and by using the multipole expansion method, we find the particular solution for the problem of wave radiation by a submerged sphere of finite depth. Furthermore, this method eliminates the need to use large and cumbersome numerical packages for the solution of such problem and leads to an infinite system of linear algebraic equations which are easily solved numerically by any standard technique. The added-mass and damping coefficients for both heave and sway motions are derived and plotted for different submersion depths of the sphere and flexural rigidity of the elastic bottom surface. It is observed that, whenever the sphere nearer to the elastic bed, the added-mass move toward to a constant value of 1, which is approximately twice of the value of added-mass of a moving sphere in a single-layer fluid flowing over a rigid and flat bottom surface.

Confinement dynamics of a semiflexible chain inside nano-spheres

NASA Astrophysics Data System (ADS)

Fathizadeh, A.; Heidari, Maziar; Eslami-Mossallam, B.; Ejtehadi, M. R.

2013-07-01

We study the conformations of a semiflexible chain, confined in nano-scaled spherical cavities, under two distinct processes of confinement. Radial contraction and packaging are employed as two confining procedures. The former method is performed by gradually decreasing the diameter of a spherical shell which envelopes a confined chain. The latter procedure is carried out by injecting the chain inside a spherical shell through a hole on the shell surface. The chain is modeled with a rigid body molecular dynamics simulation and its parameters are adjusted to DNA base-pair elasticity. Directional order parameter is employed to analyze and compare the confined chain and the conformations of the chain for two different sizes of the spheres are studied in both procedures. It is shown that for the confined chains in the sphere sizes of our study, they appear in spiral or tennis-ball structures, and the tennis-ball structure is more likely to be observed in more compact confinements. Our results also show that the dynamical procedure of confinement and the rate of the confinement are influential parameters of the structure of the chain inside spherical cavities.

Large-scale 3D simulations of ICF and HEDP targets

NASA Astrophysics Data System (ADS)

Marinak, Michael M.

2000-10-01

The radiation hydrodynamics code HYDRA continues to be developed and applied to 3D simulations of a variety of targets for both inertial confinement fusion (ICF) and high energy density physics. Several packages have been added enabling this code to perform ICF target simulations with similar accuracy as two-dimensional codes of long-time historical use. These include a laser ray trace and deposition package, a heavy ion deposition package, implicit Monte Carlo photonics, and non-LTE opacities, derived from XSN or the linearized response matrix approach.(R. More, T. Kato, Phys. Rev. Lett. 81, 814 (1998), S. Libby, F. Graziani, R. More, T. Kato, Proceedings of the 13th International Conference on Laser Interactions and Related Plasma Phenomena, (AIP, New York, 1997).) LTE opacities can also be calculated for arbitrary mixtures online by combining tabular values generated by different opacity codes. Thermonuclear burn, charged particle transport, neutron energy deposition, electron-ion coupling and conduction, and multigroup radiation diffusion packages are also installed. HYDRA can employ ALE hydrodynamics; a number of grid motion algorithms are available. Multi-material flows are resolved using material interface reconstruction. Results from large-scale simulations run on up to 1680 processors, using a combination of massively parallel processing and symmetric multiprocessing, will be described. A large solid angle simulation of Rayleigh-Taylor instability growth in a NIF ignition capsule has resolved simultaneously the full spectrum of the most dangerous modes that grow from surface roughness. Simulations of a NIF hohlraum illuminated with the initial 96 beam configuration have also been performed. The effect of the hohlraum’s 3D intrinsic drive asymmetry on the capsule implosion will be considered. We will also discuss results from a Nova experiment in which a copper sphere is crushed by a planar shock. Several interacting hydrodynamic instabilities, including the Widnall instability, cause breakup of the resulting vortex ring.

Plain packaging: an opportunity for improved international policy coherence?

PubMed Central

Lencucha, Raphael; Drope, Jeffrey

2015-01-01

This paper highlights two salient challenges at the intersection of tobacco control and macroeconomic policy-making: (i) the use of trade and investment disputes to undermine and/or stall tobacco control legislation and (ii) the inconsistency, and thus unpredictability, of country positions across the two spheres. In the interest of improving international policy coherence, the authors suggest possible solutions to these two challenges at the national and intergovernmental levels. PMID:23723441

Limiting Surface Density Method Adapted to Large Arrays of Heterogeneous Shipping Packages with Nonlinear Responses

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stover, Tracy E.; Baker, James S.; Ratliff, Michael D.

The classic Limiting Surface Density (LSD) method is an empirical calculation technique for analyzing and setting mass limits for fissile items in storage arrays. LSD is a desirable method because it can reduce or eliminate the need for lengthy detailed Monte Carlo models of storage arrays. The original (or classic) method was developed based on idealized arrays of bare spherical metal items in air-spaced cubic units in a water-reflected cubic array. In this case, the geometric and material-based surface densities were acceptably correlated by linear functions. Later updates to the method were made to allow for concrete reflection rather thanmore » water, cylindrical masses rather than spheres, different material forms, and noncubic arrays. However, in the intervening four decades since those updates, little work has been done to update the method, especially for use with contemporary highly heterogeneous shipping packages that are noncubic and stored in noncubic arrays. In this work, the LSD method is reevaluated for application to highly heterogeneous shipping packages for fissile material. The package modeled is the 9975 shipping package, currently the primary package used to store fissile material at Savannah River Site’s K-Area Complex. The package is neither cubic nor rectangular but resembles nested cylinders of stainless steel, lead, aluminum, and Celotex. The fissile content is assumed to be a cylinder of plutonium metal. The packages may be arranged in arrays with both an equal number of packages per side (package cubic) and an unequal number of packages per side (noncubic). The cubic arrangements are used to derive the 9975-specific material and geometry constants for the classic linear form LSD method. The linear form of the LSD, with noncubic array adjustment, is applied and evaluated against computational models for these packages to determine the critical unit fissile mass. Sensitivity equations are derived from the classic method, and these are also used to make projections of the critical unit fissile mass. It was discovered that the heterogeneous packages have a nonlinear surface density versus critical mass relationship compared to the acceptably linear response of bare spherical fissile masses. Methodology is developed to address the nonlinear response. In so doing, the solution to the nonlinear LSD method becomes decoupled from the critical mass of a single unit, adding to its flexibility. The ability of the method to predict changes in neutron multiplication due to perturbations in a parameter is examined to provide a basis for analyzing upset conditions. In conclusion, a full rederivation of the classic LSD method from diffusion theory is also included as this was found to be lacking in the available literature.« less

Limiting Surface Density Method Adapted to Large Arrays of Heterogeneous Shipping Packages with Nonlinear Responses

DOE PAGES

Stover, Tracy E.; Baker, James S.; Ratliff, Michael D.; ...

2018-03-02

The classic Limiting Surface Density (LSD) method is an empirical calculation technique for analyzing and setting mass limits for fissile items in storage arrays. LSD is a desirable method because it can reduce or eliminate the need for lengthy detailed Monte Carlo models of storage arrays. The original (or classic) method was developed based on idealized arrays of bare spherical metal items in air-spaced cubic units in a water-reflected cubic array. In this case, the geometric and material-based surface densities were acceptably correlated by linear functions. Later updates to the method were made to allow for concrete reflection rather thanmore » water, cylindrical masses rather than spheres, different material forms, and noncubic arrays. However, in the intervening four decades since those updates, little work has been done to update the method, especially for use with contemporary highly heterogeneous shipping packages that are noncubic and stored in noncubic arrays. In this work, the LSD method is reevaluated for application to highly heterogeneous shipping packages for fissile material. The package modeled is the 9975 shipping package, currently the primary package used to store fissile material at Savannah River Site’s K-Area Complex. The package is neither cubic nor rectangular but resembles nested cylinders of stainless steel, lead, aluminum, and Celotex. The fissile content is assumed to be a cylinder of plutonium metal. The packages may be arranged in arrays with both an equal number of packages per side (package cubic) and an unequal number of packages per side (noncubic). The cubic arrangements are used to derive the 9975-specific material and geometry constants for the classic linear form LSD method. The linear form of the LSD, with noncubic array adjustment, is applied and evaluated against computational models for these packages to determine the critical unit fissile mass. Sensitivity equations are derived from the classic method, and these are also used to make projections of the critical unit fissile mass. It was discovered that the heterogeneous packages have a nonlinear surface density versus critical mass relationship compared to the acceptably linear response of bare spherical fissile masses. Methodology is developed to address the nonlinear response. In so doing, the solution to the nonlinear LSD method becomes decoupled from the critical mass of a single unit, adding to its flexibility. The ability of the method to predict changes in neutron multiplication due to perturbations in a parameter is examined to provide a basis for analyzing upset conditions. In conclusion, a full rederivation of the classic LSD method from diffusion theory is also included as this was found to be lacking in the available literature.« less

Dynamo Catalogue: Geometrical tools and data management for particle picking in subtomogram averaging of cryo-electron tomograms.

PubMed

Castaño-Díez, Daniel; Kudryashev, Mikhail; Stahlberg, Henning

2017-02-01

Cryo electron tomography allows macromolecular complexes within vitrified, intact, thin cells or sections thereof to be visualized, and structural analysis to be performed in situ by averaging over multiple copies of the same molecules. Image processing for subtomogram averaging is specific and cumbersome, due to the large amount of data and its three dimensional nature and anisotropic resolution. Here, we streamline data processing for subtomogram averaging by introducing an archiving system, Dynamo Catalogue. This system manages tomographic data from multiple tomograms and allows visual feedback during all processing steps, including particle picking, extraction, alignment and classification. The file structure of a processing project file structure includes logfiles of performed operations, and can be backed up and shared between users. Command line commands, database queries and a set of GUIs give the user versatile control over the process. Here, we introduce a set of geometric tools that streamline particle picking from simple (filaments, spheres, tubes, vesicles) and complex geometries (arbitrary 2D surfaces, rare instances on proteins with geometric restrictions, and 2D and 3D crystals). Advanced functionality, such as manual alignment and subboxing, is useful when initial templates are generated for alignment and for project customization. Dynamo Catalogue is part of the open source package Dynamo and includes tools to ensure format compatibility with the subtomogram averaging functionalities of other packages, such as Jsubtomo, PyTom, PEET, EMAN2, XMIPP and Relion. Copyright © 2016. Published by Elsevier Inc.

Numerical simulation of a sphere moving down an incline with identical spheres placed equally apart

USGS Publications Warehouse

Ling, Chi-Hai; Jan, Chyan-Deng; Chen, Cheng-lung; Shen, Hsieh Wen

1992-01-01

This paper describes a numerical study of an elastic sphere moving down an incline with a string of identical spheres placed equally apart. Two momentum equations and a moment equation formulated for the moving sphere are solved numerically for the instantaneous velocity of the moving sphere on an incline with different angles of inclination. Input parameters for numerical simulation include the properties of the sphere (the radius, density, Poison's ratio, and Young's Modulus of elasticity), the coefficient of friction between the spheres, and a damping coefficient of the spheres during collision.

Smart SPHERES: A Telerobotic Free-Flyer for Intravehicular Activities in Space

NASA Technical Reports Server (NTRS)

Fong, Terrence; Micire, Mark J.; Morse, Ted; Park, Eric; Provencher, Chris; To, Vinh; Wheeler, D. W.; Mittman, David; Torres, R. Jay; Smith, Ernest

2013-01-01

Smart SPHERES is a prototype free-flying space robot based on the SPHERES platform. Smart SPHERES can be remotely operated by astronauts inside a spacecraft, or by mission controllers on the ground. We developed Smart SPHERES to perform a variety of intravehicular activities (IVA), such as operations inside the International Space Station (ISS). These IVA tasks include environmental monitoring surveys (radiation, sound levels, etc.), inventory, and mobile camera work. In this paper, we first discuss the motivation for free-flying space robots. We then describe the development of the Smart SPHERES prototype, including avionics, software, and data communications. Finally, we present results of initial flight tests on-board the ISS.

Smart SPHERES: A Telerobotic Free-Flyer for Intravehicular Activities in Space

NASA Technical Reports Server (NTRS)

Fong, Terrence; Micire, Mark J.; Morse, Ted; Park, Eric; Provencher, Chris

2013-01-01

Smart SPHERES is a prototype free-flying space robot based on the SPHERES platform. Smart SPHERES can be remotely operated by astronauts inside a spacecraft, or by mission controllers on the ground. We developed Smart SPHERES to perform a variety of intravehicular activities (IVA), such as operations inside the International Space Station (ISS). These IVA tasks include environmental monitoring surveys (radiation, sound levels, etc.), inventory, and mobile camera work. In this paper, we first discuss the motivation for free- flying space robots. We then describe the development of the Smart SPHERES prototype, including avionics, software, and data communications. Finally, we present results of initial flight tests on-board the ISS.

Calculated photonic structures for infrared emittance control

NASA Astrophysics Data System (ADS)

Rung, Andreas; Ribbing, Carl G.

2002-06-01

Using an available program package based on the transfer-matrix method, we calculated the photonic band structure for two different structures: a quasi-three-dimensional crystal of square air rods in a high-index matrix and an opal structure of high-index spheres in a matrix of low index, epsilon = 1.5. The high index used is representative of gallium arsenide in the thermal infrared range. The geometric parameters of the rod dimension, sphere radius, and lattice constants were chosen to give total reflectance for normal incidence, i.e., minimum thermal emittance, in either one of the two infrared atmospheric windows. For these four photonic crystals, the bulk reflectance spectra and the wavelength-averaged thermal emittance as a function of crystal thickness were calculated. The results reveal that potentially useful thermal signature suppression is obtained for crystals as thin as 20-50 mum, i.e., comparable with that of a paint layer.

Retrieving the aerosol complex refractive index using PyMieScatt: A Mie computational package with visualization capabilities

NASA Astrophysics Data System (ADS)

Sumlin, Benjamin J.; Heinson, William R.; Chakrabarty, Rajan K.

2018-01-01

The complex refractive index m = n + ik of a particle is an intrinsic property which cannot be directly measured; it must be inferred from its extrinsic properties such as the scattering and absorption cross-sections. Bohren and Huffman called this approach "describing the dragon from its tracks", since the inversion of Lorenz-Mie theory equations is intractable without the use of computers. This article describes PyMieScatt, an open-source module for Python that contains functionality for solving the inverse problem for complex m using extensive optical and physical properties as input, and calculating regions where valid solutions may exist within the error bounds of laboratory measurements. Additionally, the module has comprehensive capabilities for studying homogeneous and coated single spheres, as well as ensembles of homogeneous spheres with user-defined size distributions, making it a complete tool for studying the optical behavior of spherical particles.

High Voltage Design Guide. Volume V. Spacecraft

DTIC Science & Technology

1983-01-01

written at Boeing). 57. Langmuir , I., and Blodgett , K. B., "Currents Limited by Space Charge Between Concentric Spheres", Physical Review 23, p. 49...Transformers 66 6.3.3 Pulse Circuits 68 6.4 Packaging 68 6.4.1 Liquids 69 6.4.2 Gases 69 6.4.3 Shielding 69 6.5 Insulation 70 6.5.1 Open Construction 71 6.5.2...percent reactive liquid insulating material used to fill all intersfices within electrical parts and assemblies such as the spaces between very small

Theoretical crystal chemistry of M{sub x}(TO{sub 4}){sub y} sulfates and selenates: Topological analysis and classification of suprapolyhedral invariants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ilyushin, G. D.; Blatov, V. A.

2006-05-15

A geometric topological analysis of orthotetrahedral phases M{sub x}(TO{sub 4}){sub y} (T = S or Se) is performed for 46 sulfates and 17 selenates with the TOPOS 3.2 software package. The values of coordination sequences {l_brace}N{sub k}{r_brace} of T atoms are used as classification parameters of topologically different MTO nets. The crystal structures are analyzed within 12 coordination spheres of T sites and assigned to 26 topological types. It is established that only 7 types are common for the structures of sulfates and selenates, 16 types include only sulfates, and 3 types include only selenates. The average values of themore » bond lengths are determined: = 1.48(2) A and = 1.63(2) A. The hierarchical ordering of the crystal structure is performed using the concept of a polyhedral microensemble of the structure.« less

Interaction and charge transfer between dielectric spheres: Exact and approximate analytical solutions.

PubMed

Lindén, Fredrik; Cederquist, Henrik; Zettergren, Henning

2016-11-21

We present exact analytical solutions for charge transfer reactions between two arbitrarily charged hard dielectric spheres. These solutions, and the corresponding exact ones for sphere-sphere interaction energies, include sums that describe polarization effects to infinite orders in the inverse of the distance between the sphere centers. In addition, we show that these exact solutions may be approximated by much simpler analytical expressions that are useful for many practical applications. This is exemplified through calculations of Langevin type cross sections for forming a compound system of two colliding spheres and through calculations of electron transfer cross sections. We find that it is important to account for dielectric properties and finite sphere sizes in such calculations, which for example may be useful for describing the evolution, growth, and dynamics of nanometer sized dielectric objects such as molecular clusters or dust grains in different environments including astrophysical ones.

Molecular-based design and emerging applications of nanoporous carbon spheres

NASA Astrophysics Data System (ADS)

Liu, Jian; Wickramaratne, Nilantha P.; Qiao, Shi Zhang; Jaroniec, Mietek

2015-08-01

Over the past decade, considerable progress has been made in the synthesis and applications of nanoporous carbon spheres ranging in size from nanometres to micrometres. This Review presents the primary techniques for preparing nanoporous carbon spheres and the seminal research that has inspired their development, presented potential applications and uncovered future challenges. First we provide an overview of the synthesis techniques, including the Stöber method and those based on templating, self-assembly, emulsion and hydrothermal carbonization, with special emphasis on the design and functionalization of nanoporous carbon spheres at the molecular level. Next, we cover the key applications of these spheres, including adsorption, catalysis, separation, energy storage and biomedicine -- all of which might benefit from the regular geometry, good liquidity, tunable porosity and controllable particle-size distribution offered by nanoporous carbon spheres. Finally, we present the current challenges and opportunities in the development and commercial applications of nanoporous carbon spheres.

Molecular-based design and emerging applications of nanoporous carbon spheres.

PubMed

Liu, Jian; Wickramaratne, Nilantha P; Qiao, Shi Zhang; Jaroniec, Mietek

2015-08-01

Over the past decade, considerable progress has been made in the synthesis and applications of nanoporous carbon spheres ranging in size from nanometres to micrometres. This Review presents the primary techniques for preparing nanoporous carbon spheres and the seminal research that has inspired their development, presented potential applications and uncovered future challenges. First we provide an overview of the synthesis techniques, including the Stöber method and those based on templating, self-assembly, emulsion and hydrothermal carbonization, with special emphasis on the design and functionalization of nanoporous carbon spheres at the molecular level. Next, we cover the key applications of these spheres, including adsorption, catalysis, separation, energy storage and biomedicine — all of which might benefit from the regular geometry, good liquidity, tunable porosity and controllable particle-size distribution offered by nanoporous carbon spheres. Finally, we present the current challenges and opportunities in the development and commercial applications of nanoporous carbon spheres.

Static latching arrangement and method

DOEpatents

Morrison, Larry

1988-01-01

A latching assembly for use in latching a cable to and unlatching it from a given object in order to move an object from one location to another is disclosed herein. This assembly includes a weighted sphere mounted to one end of a cable so as to rotate about a specific diameter of the sphere. The assembly also includes a static latch adapted for connection with the object to be moved. This latch includes an internal latching cavity for containing the sphere in a latching condition and a series of surfaces and openings which cooperate with the sphere in order to move the sphere into and out of the latching cavity and thereby connect the cable to and disconnect it from the latch without using any moving parts on the latch itself.

Coordinate measuring machine test standard apparatus and method

DOEpatents

Bieg, L.F.

1994-08-30

A coordinate measuring machine test standard apparatus and method are disclosed which includes a rotary spindle having an upper phase plate and an axis of rotation, a kinematic ball mount attached to the phase plate concentric with the axis of rotation of the phase plate, a groove mounted at the circumference of the phase plate, and an arm assembly which rests in the groove. The arm assembly has a small sphere at one end and a large sphere at the other end. The small sphere may be a coordinate measuring machine probe tip and may have variable diameters. The large sphere is secured in the kinematic ball mount and the arm is held in the groove. The kinematic ball mount includes at least three mounting spheres and the groove is an angular locating groove including at least two locking spheres. The arm may have a hollow inner core and an outer layer. The rotary spindle may be a ratio reducer. The device is used to evaluate the measuring performance of a coordinate measuring machine for periodic recertification, including 2 and 3 dimensional accuracy, squareness, straightness, and angular accuracy. 5 figs.

Thermal Analysis of the Mound One Kilowatt Package

DOE Office of Scientific and Technical Information (OSTI.GOV)

Or, Chuen T.

The Mound One Kilowatt (1 KW) package was designed for the shipment of plutonium (Pu-238) with not more than 1 kW total heat dissipation. To comply with regulations, the Mound 1 kW package has to pass all the requirements under Normal Conditions of Transport (NCT; 38 degrees C ambient temperature) and Hypothetical Accident Conditions (HAC; package engulfed in fire for 30 minutes). Analytical and test results were presented in the Safety Analysis Report for Packaging (SARP) for the Mound 1 kW package, revision 1, April 1991. Some issues remained unresolved in that revision. In March 1992, Fairchild Space and Defensemore » Corporation was commissioned by the Department of Energy to perform the thermal analyses. 3-D thermal models were created to perform the NCT and HAC analyses. Four shipping configurations in the SARP revision 3 were analyzed. They were: (1) The GPHS graphite impact shell (GIS) in the threaded product can (1000 W total heat generation); (2) The fueled clads in the welded product can (1000 W total heat generation); (3) The General Purpose Heat Source (GPHS) module (750 W total heat generation); and (4) The Multi-Hundred Watt (MHW) spheres (810 W total heat generation). Results from the four cases show that the GIS or fuel clad in the product can is the worse case. The temperatures predicted under NCT and HAC in all four cases are within the design limits. The use of helium instead of argon as cover gas provides a bigger safety margin. There is a duplicate copy.« less

Ames collaborative study of cosmic ray neutrons

NASA Technical Reports Server (NTRS)

Hewitt, J. E.; Hughes, L.; Mccaslin, J. B.; Stephens, L. D.; Rindi, A.; Smith, A. R.; Thomas, R. H.; Griffith, R. V.; Welles, C. G.; Baum, J. W.

1976-01-01

The results of a collaborative study to define both the neutron flux and the spectrum more precisely and to develop a dosimetry package that can be flown quickly to altitude for solar flare events are described. Instrumentation and analysis techniques were used which were developed to measure accelerator-produced radiation. The instruments were flown in the Ames Research Center high altitude aircraft. Neutron instrumentation consisted of Bonner spheres with both active and passive detector elements, threshold detectors of both prompt-counter and activation-element types, a liquid scintillation spectrometer based on pulse-shape discrimination, and a moderated BF3 counter neutron monitor. In addition, charged particles were measured with a Reuter-Stokes ionization chamber system and dose equivalent with another instrument. Preliminary results from the first series of flights at 12.5 km (41,000 ft) are presented, including estimates of total neutron flux intensity and spectral shape and of the variation of intensity with altitude and geomagnetic latitude.

ESMPy and OpenClimateGIS: Python Interfaces for High Performance Grid Remapping and Geospatial Dataset Manipulation

NASA Astrophysics Data System (ADS)

O'Kuinghttons, Ryan; Koziol, Benjamin; Oehmke, Robert; DeLuca, Cecelia; Theurich, Gerhard; Li, Peggy; Jacob, Joseph

2016-04-01

The Earth System Modeling Framework (ESMF) Python interface (ESMPy) supports analysis and visualization in Earth system modeling codes by providing access to a variety of tools for data manipulation. ESMPy started as a Python interface to the ESMF grid remapping package, which provides mature and robust high-performance and scalable grid remapping between 2D and 3D logically rectangular and unstructured grids and sets of unconnected data. ESMPy now also interfaces with OpenClimateGIS (OCGIS), a package that performs subsetting, reformatting, and computational operations on climate datasets. ESMPy exposes a subset of ESMF grid remapping utilities. This includes bilinear, finite element patch recovery, first-order conservative, and nearest neighbor grid remapping methods. There are also options to ignore unmapped destination points, mask points on source and destination grids, and provide grid structure in the polar regions. Grid remapping on the sphere takes place in 3D Cartesian space, so the pole problem is not an issue as it can be with other grid remapping software. Remapping can be done between any combination of 2D and 3D logically rectangular and unstructured grids with overlapping domains. Grid pairs where one side of the regridding is represented by an appropriate set of unconnected data points, as is commonly found with observational data streams, is also supported. There is a developing interoperability layer between ESMPy and OpenClimateGIS (OCGIS). OCGIS is a pure Python, open source package designed for geospatial manipulation, subsetting, and computation on climate datasets stored in local NetCDF files or accessible remotely via the OPeNDAP protocol. Interfacing with OCGIS has brought GIS-like functionality to ESMPy (i.e. subsetting, coordinate transformations) as well as additional file output formats (i.e. CSV, ESRI Shapefile). ESMPy is distinguished by its strong emphasis on open source, community governance, and distributed development. The user base has grown quickly, and the package is integrating with several other software tools and frameworks. These include the Ultrascale Visualization Climate Data Analysis Tools (UV-CDAT), Iris, PyFerret, cfpython, and the Community Surface Dynamics Modeling System (CSDMS). ESMPy minimum requirements include Python 2.6, Numpy 1.6.1 and an ESMF installation. Optional dependencies include NetCDF and OCGIS-related dependencies: GDAL, Shapely, and Fiona. ESMPy is regression tested nightly, and supported on Darwin, Linux and Cray systems with the GNU compiler suite and MPI communications. OCGIS is supported on Linux, and also undergoes nightly regression testing. Both packages are installable from Anaconda channels. Upcoming development plans for ESMPy involve development of a higher order conservative grid remapping method. Future OCGIS development will focus on mesh and location stream interoperability and streamlined access to ESMPy's MPI implementation.

An algorithm for automated ROI definition in water or epoxy-filled NEMA NU-2 image quality phantoms.

PubMed

Pierce, Larry A; Byrd, Darrin W; Elston, Brian F; Karp, Joel S; Sunderland, John J; Kinahan, Paul E

2016-01-08

Drawing regions of interest (ROIs) in positron emission tomography/computed tomography (PET/CT) scans of the National Electrical Manufacturers Association (NEMA) NU-2 Image Quality (IQ) phantom is a time-consuming process that allows for interuser variability in the measurements. In order to reduce operator effort and allow batch processing of IQ phantom images, we propose a fast, robust, automated algorithm for performing IQ phantom sphere localization and analysis. The algorithm is easily altered to accommodate different configurations of the IQ phantom. The proposed algorithm uses information from both the PET and CT image volumes in order to overcome the challenges of detecting the smallest spheres in the PET volume. This algorithm has been released as an open-source plug-in to the Osirix medical image viewing software package. We test the algorithm under various noise conditions, positions within the scanner, air bubbles in the phantom spheres, and scanner misalignment conditions. The proposed algorithm shows run-times between 3 and 4 min and has proven to be robust under all tested conditions, with expected sphere localization deviations of less than 0.2 mm and variations of PET ROI mean and maximum values on the order of 0.5% and 2%, respectively, over multiple PET acquisitions. We conclude that the proposed algorithm is stable when challenged with a variety of physical and imaging anomalies, and that the algorithm can be a valuable tool for those who use the NEMA NU-2 IQ phantom for PET/CT scanner acceptance testing and QA/QC.

Coordinate measuring machine test standard apparatus and method

DOEpatents

Bieg, Lothar F.

1994-08-30

A coordinate measuring machine test standard apparatus and method which iudes a rotary spindle having an upper phase plate and an axis of rotation, a kinematic ball mount attached to the phase plate concentric with the axis of rotation of the phase plate, a groove mounted at the circumference of the phase plate, and an arm assembly which rests in the groove. The arm assembly has a small sphere at one end and a large sphere at the other end. The small sphere may be a coordinate measuring machine probe tip and may have variable diameters. The large sphere is secured in the kinematic ball mount and the arm is held in the groove. The kinematic ball mount includes at least three mounting spheres and the groove is an angular locating groove including at least two locking spheres. The arm may have a hollow inner core and an outer layer. The rotary spindle may be a ratio reducer. The device is used to evaluate the measuring performance of a coordinate measuring machine for periodic recertification, including 2 and 3 dimensional accuracy, squareness, straightness, and angular accuracy.

DHS Summary Report -- Robert Weldon

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weldon, Robert A.

This summer I worked on benchmarking the Lawrence Livermore National Laboratory fission multiplicity capability used in the Monte Carlo particle transport code MCNPX. This work involved running simulations and then comparing the simulation results with experimental experiments. Outlined in this paper is a brief description of the work completed this summer, skills and knowledge gained, and how the internship has impacted my planning for the future. Neutron multiplicity counting is a neutron detection technique that leverages the multiplicity emissions of neutrons from fission to identify various actinides in a lump of material. The identification of individual actinides in lumps ofmore » material crossing our boarders, especially U-235 and Pu-239, is a key component for maintaining the safety of the country from nuclear threats. Several multiplicity emission options from spontaneous and induced fission already existed in MCNPX 2.4.0. These options can be accessed through use of the 6th entry on the PHYS:N card. Lawrence Livermore National Laboratory (LLNL) developed a physics model for the simulation of neutron and gamma ray emission from fission and photofission that was included in MCNPX 2.7.B as an undocumented feature and then was documented in MCNPX 2.7.C. The LLNL multiplicity capability provided a different means for MCNPX to simulate neutron and gamma-ray distributions for neutron induced, spontaneous and photonuclear fission reactions. The original testing on the model for implementation into MCNPX was conducted by Gregg McKinney and John Hendricks. The model is an encapsulation of measured data of neutron multiplicity distributions from Gwin, Spencer, and Ingle, along with the data from Zucker and Holden. One of the founding principles of MCNPX was that it would have several redundant capabilities, providing the means of testing and including various physics packages. Though several multiplicity sampling methodologies already existed within MCNPX, the LLNL fission multiplicity was included to provide a separate capability for computing multiplicity as well as including several new features not already included in MCNPX. These new features include: (1) prompt gamma emission/multiplicity from neutron-induced fission; (2) neutron multiplicity and gamma emission/multiplicity from photofission; and (3) an option to enforce energy correlation for gamma neutron multiplicity emission. These new capabilities allow correlated signal detection for identifying presence of special nuclear material (SNM). Therefore, these new capabilities help meet the missions of the Domestic Nuclear Detection Office (DNDO), which is tasked with developing nuclear detection strategies for identifying potential radiological and nuclear threats, by providing new simulation capability for detection strategies that leverage the new available physics in the LLNL multiplicity capability. Two types of tests were accomplished this summer to test the default LLNL neutron multiplicity capability: neutron-induced fission tests and spontaneous fission tests. Both cases set the 6th entry on the PHYS:N card to 5 (i.e. use LLNL multiplicity). The neutron-induced fission tests utilized a simple 0.001 cm radius sphere where 0.0253 eV neutrons were released at the sphere center. Neutrons were forced to immediately collide in the sphere and release all progeny from the sphere, without further collision, using the LCA card, LCA 7j -2 (therefore density and size of the sphere were irrelevant). Enough particles were run to ensure that the average error of any specific multiplicity did not exceed 0.36%. Neutron-induced fission multiplicities were computed for U-233, U-235, Pu-239, and Pu-241. The spontaneous fission tests also used the same spherical geometry, except: (1) the LCA card was removed; (2) the density of the sphere was set to 0.001 g/cm3; and (3) instead of emitting a thermal neutron, the PAR keyword was set to PAR=SF. The purpose of the small density was to ensure that the spontaneous fission neutrons would not further interact and induce fissions (i.e. the mean free path greatly exceeded the size of the sphere). Enough particles were run to ensure that the average error of any specific spontaneous multiplicity did not exceed 0.23%. Spontaneous fission multiplicities were computed for U-238, Pu-238, Pu-240, Pu-242, Cm-242, and Cm-244. All of the computed results were compared against experimental results compiled by Holden at Brookhaven National Laboratory.« less

Plain packaging: an opportunity for improved international policy coherence?

PubMed

Lencucha, Raphael; Drope, Jeffrey

2015-06-01

This paper highlights two salient challenges at the intersection of tobacco control and macroeconomic policy-making: (i) the use of trade and investment disputes to undermine and/or stall tobacco control legislation and (ii) the inconsistency, and thus unpredictability, of country positions across the two spheres. In the interest of improving international policy coherence, the authors suggest possible solutions to these two challenges at the national and intergovernmental levels. © The Author (2013). Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Simple geometric algorithms to aid in clearance management for robotic mechanisms

NASA Technical Reports Server (NTRS)

Copeland, E. L.; Ray, L. D.; Peticolas, J. D.

1981-01-01

Global geometric shapes such as lines, planes, circles, spheres, cylinders, and the associated computational algorithms which provide relatively inexpensive estimates of minimum spatial clearance for safe operations were selected. The Space Shuttle, remote manipulator system, and the Power Extension Package are used as an example. Robotic mechanisms operate in quarters limited by external structures and the problem of clearance is often of considerable interest. Safe clearance management is simple and suited to real time calculation, whereas contact prediction requires more precision, sophistication, and computational overhead.

Microwave Reflectivity of Deposited Aluminum Films for Passive Relay Communications

NASA Technical Reports Server (NTRS)

Cuddihy, William F.; Shreve, Lloyd H.

1961-01-01

Reflectivity measurements from 400 Mc/sec to 10 kMc/sec on 2,200 A thick aluminum deposited on 1/2-mil-thick Mylar film show this material to be a very good reflector of radio waves. Measurements made under conditions of stress and temperature which would be encountered by a communications sphere, such as Project Echo (1960 Iota), showed very little deterioration of the high reflectivity. packaging effects also caused very little reflectivity change. Under conditions of severe temperature cycling, aluminum removal and decreased reflectivity occurred.

Space Radiation Detector with Spherical Geometry

NASA Technical Reports Server (NTRS)

Wrbanek, John D. (Inventor); Fralick, Gustave C. (Inventor); Wrbanek, Susan Y. (Inventor)

2011-01-01

A particle detector is provided, the particle detector including a spherical Cherenkov detector, and at least one pair of detector stacks. In an embodiment of the invention, the Cherenkov detector includes a sphere of ultraviolet transparent material, coated by an ultraviolet reflecting material that has at least one open port. The Cherenkov detector further includes at least one photodetector configured to detect ultraviolet light emitted from a particle within the sphere. In an embodiment of the invention, each detector stack includes one or more detectors configured to detect a particle traversing the sphere.

Space Radiation Detector with Spherical Geometry

NASA Technical Reports Server (NTRS)

Wrbanek, John D. (Inventor); Fralick, Gustave C. (Inventor); Wrbanek, Susan Y. (Inventor)

2012-01-01

A particle detector is provided, the particle detector including a spherical Cherenkov detector, and at least one pair of detector stacks. In an embodiment of the invention, the Cherenkov detector includes a sphere of ultraviolet transparent material, coated by an ultraviolet reflecting material that has at least one open port. The Cherenkov detector further includes at least one photodetector configured to detect ultraviolet light emitted from a particle within the sphere. In an embodiment of the invention, each detector stack includes one or more detectors configured to detect a particle traversing the sphere.

Solar-B E/PO Program at Chabot Space and Science Center, Oakland, California

NASA Astrophysics Data System (ADS)

Burress, B. S.

2005-05-01

Chabot Space and Science Center in Oakland, California, conducts the Education/Public Outreach program for the Lockheed-Martin Solar and Astrophysics Lab Solar-B Focal Plane Package project. Since opening its doors in August 2000, Chabot has carried out this program in activities and educational products in the public outreach, informal education, and formal education spheres. We propose a poster presentation that illustrates the spectrum of our Solar-B E/PO program. Solar-B, scheduled to launch in September 2006, is another step in an increasingly sophisticated investigation and understanding of our Sun, its behavior, and its effects on the Earth and our technological civilization. A mission of the Japan Aerospace Exploration Agency (JAXA), Solar-B is an international collaboration between Japan, the US/NASA, and the UK/PPARC. Solar-B's main optical telescope, extreme ultraviolet imaging spectrometer, and x-ray telescope will collect data on the Sun's magnetic dynamics from the photosphere through the corona at higher spatial and time resolution than on current and previous solar satellite missions, furthering our understanding of the Sun's behavior and, ultimately, its effects on the Earth. Chabot's E/PO program for the Lockheed-Martin Solar-B Focal Plane Package is multi-faceted, including elements focused on technology/engineering, solar physics, and Sun-Earth Connection themes. In the Public Outreach arena, we conduct events surrounding NASA Sun-Earth Day themes and programs other live and/or interactive events, facilitate live solar viewing, and present a series of exhibits focused on the Solar-B and other space-based missions, the dynamic Sun, and light and optics. In the Informal Education sector we run a solar day camp for kids and produce educational products, including a poster on the Solar-B mission and CDROM multimedia packages. In Formal Education, we develop classroom curriculum guides and conduct workshops training teachers in their implementation. Our poster presentation will address the highlights of our program in all three of these areas.

Prognostics Health Management Model for LED Package Failure Under Contaminated Environment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lall, Pradeep; Zhang, Hao; Davis, J Lynn

2015-06-06

The reliability consideration of LED products includes both luminous flux drop and color shift. Previous research either talks about luminous maintenance or color shift, because luminous flux degradation usually takes very long time to observe. In this paper, the impact of a VOC (volatile organic compound) contaminated luminous flux and color stability are examined. As a result, both luminous degradation and color shift had been recorded in a short time. Test samples are white, phosphor-converted, high-power LED packages. Absolute radiant flux is measured with integrating sphere system to calculate the luminous flux. Luminous flux degradation and color shift distance weremore » plotted versus aging time to show the degradation pattern. A prognostic health management (PHM) method based on the state variables and state estimator have been proposed in this paper. In this PHM framework, unscented kalman filter (UKF) was deployed as the carrier of all states. During the estimation process, third order dynamic transfer function was used to implement the PHM framework. Both of the luminous flux and color shift distance have been used as the state variable with the same PHM framework to exam the robustness of the method. Predicted remaining useful life is calculated at every measurement point to compare with the tested remaining useful life. The result shows that state estimator can be used as the method for the PHM of LED degradation with respect to both luminous flux and color shift distance. The prediction of remaining useful life of LED package, made by the states estimator and data driven approach, falls in the acceptable error-bounds (20%) after a short training of the estimator.« less

The effect of disorder of small spheres on the photonic properties of the inverse binary NaCl-like structure

NASA Astrophysics Data System (ADS)

Pattabhiraman, Harini; Dijkstra, Marjolein

2017-09-01

Inverse opal structures are experimentally realisable photonic band gap materials. They suffer from the drawback of possessing band gaps that are extremely susceptible to structural disorders. A binary colloidal NaCl lattice, which is also experimentally realisable, is a promising alternative to these opals. In this work, we systematically analyse the effect of structural disorder of the small spheres on the photonic properties of an inverse binary NaCl lattice with a size ratio of 0.30 between the small and large spheres. The types of structural disorders studied include the position of the small spheres in the octahedral void of the large spheres, polydispersity in size of the small spheres, and the fraction of small spheres in the crystal. We find a low susceptibility of the band gap of the inverse NaCl lattice to the disorder of the small spheres.

Training of Industrial Sphere Managers in a Specially Organized Education Environment

ERIC Educational Resources Information Center

Gorshenina, Margarita; Firsova, Elena

2016-01-01

The professional activity of industrial sphere managers has an integrated character and includes managerial, economic and production activity. Due to this the structure of readiness of industrial sphere managers for professional activity is composed of three components: subject, reflexive and technological ones. The objective of this paper…

4-channels coherent perfect absorption (CPA)-type demultiplexer using plasmonic nano spheres

NASA Astrophysics Data System (ADS)

Soltani, Mohamadreza; Keshavarzi, Rasul

2017-10-01

The current research represents a nanoscale and compact 4-channels plasmonic demultiplexer. It includes eight coherent perfect absorption (CPA) - type filters. The operation principle is based on the absorbable formation of a conductive path in the dielectric layer of a plasmonic nano-spheres waveguide. Since the CPA efficiency depends strongly on the number of plasmonic nano-spheres and the nano spheres location, an efficient binary optimization method based on the Particle Swarm Optimization algorithm is used to design an optimized array of the plasmonic nano-sphere in order to achieve the maximum absorption coefficient in the 'off' state.

Metallic nanospheres embedded in nanowires initiated on nanostructures and methods for synthesis thereof

DOEpatents

Zaidi, Saleem [Albuquerque, NM; Tringe, Joseph W [Walnut Creek, CA; Vanamu, Ganesh [Sunnyvale, CA; Prinja, Rajiv [Albuquerque, NM

2012-01-10

A nanostructure includes a nanowire having metallic spheres formed therein, the spheres being characterized as having at least one of about a uniform diameter and about a uniform spacing there between. A nanostructure in another embodiment includes a substrate having an area with a nanofeature; and a nanowire extending from the nanofeature, the nanowire having metallic spheres formed therein, the spheres being characterized as having at least one of about a uniform diameter and about a uniform spacing there between. A method for forming a nanostructure is also presented. A method for reading and writing data is also presented. A method for preparing nanoparticles is also presented.

Aerial View of StenniSphere

NASA Image and Video Library

2001-04-25

StenniSphere, the John C. Stennis Space Center's visitor center in Hancock County, Miss., features a 14,000-square-foot museum and outdoor exhibits about Stennis Space Center. Designed to entertain while educating, StenniSphere includes informative displays and exhibits from NASA, the Naval Meteorology and Oceanography Command, and other resident agencies. Recently named Mississippi's Travel Attraction of the Year, StenniSphere hosted a quarter of a million visitors in its first year and is a major school field trip destination.

Aerial View of StenniSphere

NASA Technical Reports Server (NTRS)

2001-01-01

StenniSphere, the John C. Stennis Space Center's visitor center in Hancock County, Miss., features a 14,000-square-foot museum and outdoor exhibits about Stennis Space Center. Designed to entertain while educating, StenniSphere includes informative displays and exhibits from NASA, the Naval Meteorology and Oceanography Command, and other resident agencies. Recently named Mississippi's Travel Attraction of the Year, StenniSphere hosted a quarter of a million visitors in its first year and is a major school field trip destination.

SPHERES: Synchronized, Position, Hold, Engage, Reorient, Experimental Satellites: SPHERES/Astrobee Working Group (SAWG)

NASA Technical Reports Server (NTRS)

Benavides, Jose

2017-01-01

SPHERES/Astrobee Working Group (SAWG) Quarterly meeting. Membership includes MIT, FIT, AFS, DARPA, CASIS, SJSU, and NASA (HQ, KSC, JSC, MSFC, and ARC)Face-to-Face, twice a year Purpose: Information sharing across the SPHERES community Program office shares National Lab Facility availability Status of resources (batteries, CO2 tanks, etc.), Overall Calendar (scheduled Test Sessions, up mass return), and Updates on new PD, Investigations, and ISS infrastructure. Provide the SPHERES community (PD, investigators, etc.) with up-to-date information to determine opportunities to use the NL Facility Discuss proposed changes updates to SPHERES Nat Lab which may be required to support a specific activity or research. Discuss specific support requests made to the ISS Office.

Libpsht - algorithms for efficient spherical harmonic transforms

NASA Astrophysics Data System (ADS)

Reinecke, M.

2011-02-01

Libpsht (or "library for performant spherical harmonic transforms") is a collection of algorithms for efficient conversion between spatial-domain and spectral-domain representations of data defined on the sphere. The package supports both transforms of scalars and spin-1 and spin-2 quantities, and can be used for a wide range of pixelisations (including HEALPix, GLESP, and ECP). It will take advantage of hardware features such as multiple processor cores and floating-point vector operations, if available. Even without this additional acceleration, the employed algorithms are among the most efficient (in terms of CPU time, as well as memory consumption) currently being used in the astronomical community. The library is written in strictly standard-conforming C90, ensuring portability to many different hard- and software platforms, and allowing straightforward integration with codes written in various programming languages like C, C++, Fortran, Python etc. Libpsht is distributed under the terms of the GNU General Public License (GPL) version 2 and can be downloaded from .

Libpsht: Algorithms for Efficient Spherical Harmonic Transforms

NASA Astrophysics Data System (ADS)

Reinecke, Martin

2010-10-01

Libpsht (or "library for Performing Spherical Harmonic Transforms") is a collection of algorithms for efficient conversion between spatial-domain and spectral-domain representations of data defined on the sphere. The package supports transforms of scalars as well as spin-1 and spin-2 quantities, and can be used for a wide range of pixelisations (including HEALPix, GLESP and ECP). It will take advantage of hardware features like multiple processor cores and floating-point vector operations, if available. Even without this additional acceleration, the employed algorithms are among the most efficient (in terms of CPU time as well as memory consumption) currently being used in the astronomical community. The library is written in strictly standard-conforming C90, ensuring portability to many different hard- and software platforms, and allowing straightforward integration with codes written in various programming languages like C, C++, Fortran, Python etc. Libpsht is distributed under the terms of the GNU General Public License (GPL) version 2. Development on this project has ended; its successor is libsharp (ascl:1402.033).

High-Energy Space Propulsion Based on Magnetized Target Fusion

NASA Technical Reports Server (NTRS)

Thio, Y. C. F.; Landrum, D. B.; Freeze, B.; Kirkpatrick, R. C.; Gerrish, H.; Schmidt, G. R.

1999-01-01

Magnetized target fusion is an approach in which a magnetized target plasma is compressed inertially by an imploding material wall. A high energy plasma liner may be used to produce the required implosion. The plasma liner is formed by the merging of a number of high momentum plasma jets converging towards the center of a sphere where two compact toroids have been introduced. Preliminary 3-D hydrodynamics modeling results using the SPHINX code of Los Alamos National Laboratory have been very encouraging and confirm earlier theoretical expectations. The concept appears ready for experimental exploration and plans for doing so are being pursued. In this talk, we explore conceptually how this innovative fusion approach could be packaged for space propulsion for interplanetary travel. We discuss the generally generic components of a baseline propulsion concept including the fusion engine, high velocity plasma accelerators, generators of compact toroids using conical theta pinches, magnetic nozzle, neutron absorption blanket, tritium reprocessing system, shock absorber, magnetohydrodynamic generator, capacitor pulsed power system, thermal management system, and micrometeorite shields.

Development and fabrication of insulator seals for thermionic diodes

NASA Technical Reports Server (NTRS)

Poirier, V. L.

1972-01-01

Eight different types of cermet seals for thermionic diodes were investigated: (1) 1 micron Al2O3 with Nb spheres; (2) 200 A Al2O3 with Nb spheres; (3) 1 micron Al2O3 with Nb 1% Zr spheres; (4) 200 A Al2O3 with Nb 1% Zr spheres; (5) Pure Y2O3 with Nb 1% Zr spheres; (6) Y2O3 3% ZrO2 with Nb 1% Zr spheres; (7) Y2O3 10% ZrO2 with Nb 1% Zr spheres; and (8) ZrO2 12% Y2O3 with Nb 1% Zr spheres. Investigations were made to determine the most favorable fabrication techniques and the effect of the bonding cycle, (length of bonding time and shutdown sequences). The analysis of the seals included tensile test, vacuum test, electrical test and metallurgical examination. At the conclusion of the development phase, 36 seals were fabricated for delivery for evaluation.

Filtered back-projection algorithm for Compton telescopes

DOEpatents

Gunter, Donald L [Lisle, IL

2008-03-18

A method for the conversion of Compton camera data into a 2D image of the incident-radiation flux on the celestial sphere includes detecting coincident gamma radiation flux arriving from various directions of a 2-sphere. These events are mapped by back-projection onto the 2-sphere to produce a convolution integral that is subsequently stereographically projected onto a 2-plane to produce a second convolution integral which is deconvolved by the Fourier method to produce an image that is then projected onto the 2-sphere.

Recent progress in hollow sphere-based electrodes for high-performance supercapacitors

NASA Astrophysics Data System (ADS)

Zhao, Yan; Chen, Min; Wu, Limin

2016-08-01

Hollow spheres have drawn much attention in the area of energy storage and conversion, especially in high-performance supercapacitors owing to their well-defined morphologies, uniform size, low density and large surface area. And quite some significant breakthroughs have been made in advanced supercapacitor electrode materials with hollow sphere structures. In this review, we summarize and discuss the synthesis and application of hollow spheres with controllable structure and morphology as electrode materials for supercapacitors. First, we briefly introduce the fabrication strategies of hollow spheres for electrode materials. Then, we discuss in detail the recent advances in various hollow sphere-based electrode materials for supercapacitors, including single-shelled, yolk-shelled, urchin-like, double-shelled, multi-shelled, and mesoporous hollow structure-based symmetric and asymmetric supercapacitor devices. We conclude this review with some perspectives on the future research and development of the hollow sphere-based electrode materials.

Recent progress in hollow sphere-based electrodes for high-performance supercapacitors.

PubMed

Zhao, Yan; Chen, Min; Wu, Limin

2016-08-26

Hollow spheres have drawn much attention in the area of energy storage and conversion, especially in high-performance supercapacitors owing to their well-defined morphologies, uniform size, low density and large surface area. And quite some significant breakthroughs have been made in advanced supercapacitor electrode materials with hollow sphere structures. In this review, we summarize and discuss the synthesis and application of hollow spheres with controllable structure and morphology as electrode materials for supercapacitors. First, we briefly introduce the fabrication strategies of hollow spheres for electrode materials. Then, we discuss in detail the recent advances in various hollow sphere-based electrode materials for supercapacitors, including single-shelled, yolk-shelled, urchin-like, double-shelled, multi-shelled, and mesoporous hollow structure-based symmetric and asymmetric supercapacitor devices. We conclude this review with some perspectives on the future research and development of the hollow sphere-based electrode materials.

Experience the Moon

NASA Astrophysics Data System (ADS)

Ortiz-Gil, A.; Benacchio, L.; Boccato, C.

2011-10-01

The Moon is, together with the Sun, the very first astronomical object that we experience in our life. As this is an exclusively visual experience, people with visual impairments need a different mode to experience it too. This statement is especially true when events, such as more and more frequent public observations of sky, take place. This is the reason why we are preparing a special package for visual impaired people containing three brand new items: 1. a tactile 3D Moon sphere in Braille with its paper key in Braille. To produce it we used imaging data obtained by NASA's mission Clementine, along with free image processing and 3D rendering software. In order to build the 3D small scale model funding by Europlanet and the Italian Ministry for Research have been used. 2. a multilingual web site for visually impaired users of all ages, on basic astronomy together with an indepth box about the Moon; 3. a book in Braille with the same content of the Web site mentioned above. All the items will be developed with the collaboration of visually impaired people that will check each step of the project and support their comments and criticism to improve it. We are going to test this package during the next International Observe the Moon Night event. After a first testing phase we'll collect all the feedback data in order to give an effective form to the package. Finally the Moon package could be delivered to all those who will demand it for outreach or educational goals.

Improvements in Modeling Au Sphere Non-LTE X-ray Emission

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rosen, M D; Scott, H A; Suter, L J

2008-10-30

We've previously reported on experiments at the Omega laser at URLLE, in which 1.0 mm in diameter, Au coated, spheres, were illuminated at either 10{sup 14} W/cm{sup 2} (10 kJ/3 ns) or at 10{sup 15} W/cm{sup 2} (30 kJ/1 ns). Spectral information on the 1 keV thermal x-rays, as well as the multi-keV M-band were obtained. We compared a variety of non-LTE atomic physics packages to this data with varying degrees of success. In this paper we broaden the scope of the investigation, and compare the data to newer models: (1) An improved Detailed Configuration Accounting (DCA) method; and (2)more » This model involves adjustments to the standard XSN non-LTE model which lead to a better match of coronal emission as calculated by XSN to that calculated by SCRAM, a more sophisticated stand-alone model. We show some improvements in the agreement with Omega data when using either of these new approaches.« less

Sterically allowed configuration space for amino acid dipeptides

NASA Astrophysics Data System (ADS)

Caballero, Diego; Maatta, Jukka; Sammalkorpi, Maria; O'Hern, Corey; Regan, Lynne

2014-03-01

Despite recent improvements in computational methods for protein design, we still lack a quantitative, predictive understanding of the intrinsic propensities for amino acids to be in particular backbone or side-chain conformations. This question has remained unsettled for years because of the discrepancies between different experimental approaches. To address it, I performed all-atom hard-sphere simulations of hydrophobic residues with stereo-chemical constraints and non-attractive steric interactions between non-bonded atoms for ALA, ILE, LEU and VAL dipeptide mimetics. For these hard-sphere MD simulations, I show that transitions between α-helix and β-sheet structures only occur when the bond angle τ(N -Cα - C) >110° , and the probability distribution of bond angles for structures in the `bridge' region of ϕ- ψ space is shifted to larger angles compared to that in other regions. In contrast, the relevant bond-angle distributions obtained from most molecular dynamics packages are broader and shifter to larger values. I encounter similar correlations between bond angles and side-chain dihedral angles. The success of these studies is an argument for re-incorporating local stereochemical constraints into computational protein design methodology.

Behavior of a nano-particle and a polymer molecule in a nano-scale four-roll mill

NASA Astrophysics Data System (ADS)

Vo, Minh; Papavassiliou, Dimitrios

2016-11-01

The four-roll mill device could be used to create a mixed flow from purely extensional stresses to completely rotational through the proper selection of speed and direction of each of the four cylindrical rollers. Considerable research has been done with this device for macroscale rheological studies.. In our study, the dissipative particle dynamics (DPD) method was employed to investigate the behavior of a nano-sphere and a polymer molecule in different conditions within a four-roll mill device. Hydrophilic properties of each roll were generated by adjusting interaction parameters and using bounce back boundary condition at the solid surface. All simulations were run up to 4x106 time steps at room temperature using the open source LAMMPS package. After the flow in the system reached equilibrium, a nano-sphere and then a polymer chain were released at the center of the simulation box. Their trajectories were recorded at different shear rate conditions. The propagation of nanosphere in different rotational flow will be discussed. Additionally, the deformation of polymer chains will be compared to that in a simple shear flow.

Controllable Synthesis of Functional Hollow Carbon Nanostructures with Dopamine As Precursor for Supercapacitors.

PubMed

Liu, Chao; Wang, Jing; Li, Jiansheng; Luo, Rui; Shen, Jinyou; Sun, Xiuyun; Han, Weiqing; Wang, Lianjun

2015-08-26

N-doped hollow carbon spheres (N-HCSs) are promising candidates as electrode material for supercapacitor application. In this work, we report a facile one-step synthesis of discrete and highly dispersible N-HCSs with dopamine (DA) as a carbon precursor and TEOS as a structure-assistant agent in a mixture containing water, ethanol, and ammonia. The architectures of resultant N-HCSs, including yolk-shell hollow carbon spheres (YS-HCSs), single-shell hollow carbon spheres (SS-HCSs), and double-shells hollow carbon spheres (DS-HCSs), can be efficiently controlled through the adjustment of the amount of ammonia. To explain the relation and formation mechanism of these hollow carbon structures, the samples during the different synthetic steps, including polymer/silica spheres, carbon/silica spheres and silica spheres by combustion in air, were characterized by TEM. Electrochemical measurements performed on YS-HCSs, SS-HCSs, and DS-HCSs showed high capacitance with 215, 280, and 381 F g(-1), respectively. Moreover, all the nitrogen-doped hollow carbon nanospheres showed a good cycling stability 97.0% capacitive retention after 3000 cycles. Notably, the highest capacitance of DS-HCSs up to 381 F g(-1) is higher than the capacitance reported so far for many carbon-based materials, which may be attributed to the high surface area, hollow structure, nitrogen functionalization, and double-shell architecture. These kinds of N-doped hollow-structured carbon spheres may show promising prospects as advanced energy storage materials and catalyst supports.

Sphere based fluid systems

NASA Technical Reports Server (NTRS)

Elleman, Daniel D. (Inventor); Wang, Taylor G. (Inventor)

1989-01-01

Systems are described for using multiple closely-packed spheres. In one system for passing fluid, a multiplicity of spheres lie within a container, with all of the spheres having the same outside diameter and with the spheres being closely nested in one another to create multiple interstitial passages of a known size and configuration and smooth walls. The container has an inlet and outlet for passing fluid through the interstitial passages formed between the nested spheres. The small interstitial passages can be used to filter out material, especially biological material such as cells in a fluid, where the cells can be easily destroyed if passed across sharp edges. The outer surface of the spheres can contain a material that absorbs a constitutent in the flowing fluid, such as a particular contamination gas, or can contain a catalyst to chemically react the fluid passing therethrough, the use of multiple small spheres assuring a large area of contact of these surfaces of the spheres with the fluid. In a system for storing and releasing a fluid such as hydrogen as a fuel, the spheres can include a hollow shell containing the fluid to be stored, and located within a compressable container that can be compressed to break the shells and release the stored fluid.

StenniSphere

NASA Image and Video Library

2000-10-25

The John C. Stennis Space Center's visitor center, StenniSphere, is one of Mississippi's leading tourist attractions and features a 14,000-square-foot interactive review of Stennis Space Center's role in America's space program. Designed to entertain while educating, StenniSphere includes informative displays and exhibits from NASA, the Naval Meteorology and Oceanography Command, and other resident agencies located at Stennis Space Center in Hancock County, Miss.

StenniSphere

NASA Technical Reports Server (NTRS)

2000-01-01

The John C. Stennis Space Center's visitor center, StenniSphere, is one of Mississippi's leading tourist attractions and features a 14,000-square-foot interactive review of Stennis Space Center's role in America's space program. Designed to entertain while educating, StenniSphere includes informative displays and exhibits from NASA, the Naval Meteorology and Oceanography Command, and other resident agencies located at Stennis Space Center in Hancock County, Miss.

Modelling and Display of the Ultraviolet Sky

NASA Astrophysics Data System (ADS)

Daniels, J.; Henry, R.; Murthy, J.; Allen, M.; McGlynn, T. A.; Scollick, K.

1994-12-01

A computer program is currently under development to model in 3D - one dimension of which is wavelength - all the known and major speculated sources of ultraviolet (900 A - 3100 A ) radiation over the celestial sphere. The software is being written in Fortran 77 and IDL and currently operates under IRIX (the operating system of the Silicon Graphics Iris Machine); all output models are in FITS format. Models along with display software will become available to the astronomical community. The Ultraviolet Sky Model currently includes the Zodiacal Light, Point Sources of Emission, and the Diffuse Galactic Light. The Ultraviolet Sky Model is currently displayed using SkyView: a package under development at NASA/ GSFC, which allows users to retrieve and display publically available all-sky astronomical survey data (covering many wavebands) over the Internet. We present a demonstration of the SkyView display of the Ultraviolet Model. The modelling is a five year development project: the work illustrated here represents product output at the end of year one. Future work includes enhancements to the current models and incorporation of the following models: Galactic Molecular Hydrogen Fluorescence; Galactic Highly Ionized Atomic Line Emission; Integrated Extragalactic Light; and speculated sources in the intergalactic medium such as Ionized Plasma and radiation from Non-Baryonic Particle Decay. We also present a poster which summarizes the components of the Ultraviolet Sky Model and outlines a further package that will be used to display the Ultraviolet Model. This work is supported by United States Air Force Contract F19628-93-K-0004. Dr J. Daniels is supported with a post-doctoral Fellowship from the Leverhulme Foundation, London, United Kingdom. We are also grateful for the encouragement of Dr Stephen Price (Phillips Laboratory, Hanscomb Air Force Base, MA)

Use of equivalent spheres to model the relation between radar reflectivity and optical extinction of ice cloud particles.

PubMed

Donovan, David Patrick; Quante, Markus; Schlimme, Ingo; Macke, Andreas

2004-09-01

The effect of ice crystal size and shape on the relation between radar reflectivity and optical extinction is examined. Discrete-dipole approximation calculations of 95-GHz radar reflectivity and ray-tracing calculations are applied to ice crystals of various habits and sizes. Ray tracing was used primarily to calculate optical extinction and to provide approximate information on the lidar backscatter cross section. The results of the combined calculations are compared with Mie calculations applied to collections of different types of equivalent spheres. Various equivalent sphere formulations are considered, including equivalent radar-lidar spheres; equivalent maximum dimension spheres; equivalent area spheres, and equivalent volume and equivalent effective radius spheres. Marked differences are found with respect to the accuracy of different formulations, and certain types of equivalent spheres can be used for useful prediction of both the radar reflectivity at 95 GHz and the optical extinction (but not lidar backscatter cross section) over a wide range of particle sizes. The implications of these results on combined lidar-radar ice cloud remote sensing are discussed.

Theoretical and experimental studies on silica-coated carbon spheres composites

NASA Astrophysics Data System (ADS)

Guo, Xingmei; Liu, Haixing; Shen, Yinghua; Niu, Mei; Yang, Yongzhen; Liu, Xuguang

2013-10-01

In order to prepare carbon-based photonic crystals, first of all, theoretical modeling calculation was used to predict the bandgap characteristics of silica-coated carbon spheres. Then, silica-coated carbon spheres composites were synthesized using tetraethyl orthosilicate as precursor of silica by a sol-gel method combined with Stöber method. Effect of reaction conditions on surface coating of carbon spheres with silica, including the pH, the amount of precursor and reaction time, was emphasized. The morphology and structure of the composites and the effect coating of carbon spheres with silica were characterized by field-emission scanning electron microscopy, high resolution transmission electron microscopy and Fourier-transform infrared spectrometry. The coating ratio of silica was investigated by thermogravimetry. The results show that pH value played an important role in coating reaction, the dosage of the precursor and reaction time had significant effect on coating layer thickness, that is, coating ratio. Carbon spheres coated with silica had good dispersibility and dispersion stability in water and ethanol, which is preconditions of reactivity of carbon spheres in liquid phase and lays the basis for the application of carbon spheres.

Using the TSAR electromagnetic modeling system

NASA Astrophysics Data System (ADS)

Pennock, S. T.; Laguna, G. W.

1993-09-01

A new user, upon receipt of the TSAR EM modeling system, may be overwhelmed by the number of software packages to learn and the number of manuals associated with those packages. This is a document to describe the creation of a simple TSAR model, beginning with an MGED solid and continuing the process through final results from TSAR. It is not intended to be a complete description of all the parts of the TSAR package. Rather, it is intended simply to touch on all the steps in the modeling process and to take a new user through the system from start to finish. There are six basic parts to the TSAR package. The first, MGED, is part of the BRL-CAD package and is used to create a solid model. The second part, ANASTASIA, is the program used to sample the solid model and create a finite-difference mesh. The third program, IMAGE, lets the user view the mesh itself and verify its accuracy. If everything about the mesh is correct, the process continues to the fourth step, SETUP-TSAR, which creates the parameter files for compiling TSAR and the input file for running a particular simulation. The fifth step is actually running TSAR, the field modeling program. Finally, the output from TSAR is placed into SIG, B2RAS or another program for post-processing and plotting. Each of these steps will be described below. The best way to learn to use the TSAR software is to actually create and run a simple test problem. As an example of how to use the TSAR package, let's create a sphere with a rectangular internal cavity, with conical and cylindrical penetrations connecting the outside to the inside, and find the electric field inside the cavity when the object is exposed to a Gaussian plane wave. We will begin with the solid modeling software, MGED, a part of the BRL-CAD modeling release.

Using the TSAR Electromagnetic modeling system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pennock, S.T.; Laguna, G.W.

1993-09-01

A new user, upon receipt of the TSAR EM modeling system, may be overwhelmed by the number of software packages to learn and the number of manuals associated with those packages. This is a document to describe the creation of a simple TSAR model, beginning with an MGED solid and continuing the process through final results from TSAR. It is not intended to be a complete description of all the parts of the TSAR package. Rather, it is intended simply to touch on all the steps in the modeling process and to take a new user through the system frommore » start to finish. There are six basic parts to the TSAR package. The first, MGED, is part of the BRL-CAD package and is used to create a solid model. The second part, ANASTASIA, is the program used to sample the solid model and create a finite -- difference mesh. The third program, IMAGE, lets the user view the mesh itself and verify its accuracy. If everything about the mesh is correct, the process continues to the fourth step, SETUP-TSAR, which creates the parameter files for compiling TSAR and the input file for running a particular simulation. The fifth step is actually running TSAR, the field modeling program. Finally, the output from TSAR is placed into SIG, B2RAS or another program for post-processing and plotting. Each of these steps will be described below. The best way to learn to use the TSAR software is to actually create and run a simple test problem. As an example of how to use the TSAR package, let`s create a sphere with a rectangular internal cavity, with conical and cylindrical penetrations connecting the outside to the inside, and find the electric field inside the cavity when the object is exposed to a Gaussian plane wave. We will begin with the solid modeling software, MGED, a part of the BRL-CAD modeling release.« less

The Precision Expandable Radar Calibration Sphere (PERCS) With Applications for Laser Imaging and Ranging

NASA Astrophysics Data System (ADS)

Bernhardt, P.; Nicholas, A.; Thomas, L.; Davis, M.; Hoberman, C.; Davis, M.

The Naval Research Laboratory will provide an orbiting calibration sphere to be used with ground-based laser imaging telescopes and HF radio systems. The Precision Expandable Radar Calibration Sphere (PERCS) is a practical, reliable, high-performance HF calibration sphere and laser imaging target to orbit at about 600 km altitude. The sphere will be made of a spherical wire frame with aspect independent radar cross section in the 3 to 35 MHz frequency range. The necessary launch vehicle to place the PERCS in orbit will be provided by the Department of Defense Space Test Program. The expandable calibration target has a stowed diameter of 1 meter and a fully deployed diameter of 10.2 meters. A separate deployment mechanism is provided for the sphere. After deployment, the Precision Expandable Radar Calibration Sphere (PERCS) with 180 vertices will be in a high inclination orbit to scatter radio pulses from a number of ground systems, including (1) over-the-horizon (OTH) radars operated by the United States and Australia; (2) high power HF facilities such as HAARP in Alaska, EISCAT in Norway, and Arecibo in Puerto Rico; (3) the chain of high latitude SuperDARN radars used for auroral region mapping; and (4) HF direction finding for Navy ships. With the PERCS satellite, the accuracy of HF radars can be periodically checked for range, elevation, and azimuth errors. In addition, each of the 360 vertices on the PERCS sphere will support an optical retro-reflector for operations with ground laser facilities used to track satellites. The ground laser systems will be used to measure the precise location of the sphere within one cm accuracy and will provide the spatial orientation of the sphere as well as the rotation rate. The Department of Defense facilities that can use the corner-cube reflectors on the PERCS include (1) the Air Force Maui Optical Site (AMOS), (2) the Starfire Optical Range (SOR), and (3) the NRL Optical Test Facility (OTF).

Chinese Armillary Spheres

NASA Astrophysics Data System (ADS)

Sun, Xiaochun

The armillary sphere was perhaps the most important type of astronomical instrument in ancient China. It was first invented by Luoxia Hong in the first century BC. After Han times, the structure of the armillary sphere became increasingly sophisticated by including more and more rings representing various celestial movements as recognized by the Chinese astronomers. By the eighth century, the Chinese armillary sphere consisted of three concentric sets of rings revolving on the south-north polar axis. The relative position of the rings could be adjusted to reflect the precession of the equinoxes and the regression of the Moon's nodes along the ecliptic. To counterbalance the defect caused by too many rings, Guo Shoujing from the late thirteenth century constructed the Simplified Instruments which reorganized the rings of the armillary sphere into separate instruments for measuring equatorial coordinates and horizontal coordinates. The armillary sphere was still preserved because it was a good illustration of celestial movements. A fifteenth-century replica of Guo Shoujing's armillary sphere still exists today.

Verification of statistical method CORN for modeling of microfuel in the case of high grain concentration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chukbar, B. K., E-mail: bchukbar@mail.ru

Two methods of modeling a double-heterogeneity fuel are studied: the deterministic positioning and the statistical method CORN of the MCU software package. The effect of distribution of microfuel in a pebble bed on the calculation results is studied. The results of verification of the statistical method CORN for the cases of the microfuel concentration up to 170 cm{sup –3} in a pebble bed are presented. The admissibility of homogenization of the microfuel coating with the graphite matrix is studied. The dependence of the reactivity on the relative location of fuel and graphite spheres in a pebble bed is found.

Pool boiling from rotating and stationary spheres in liquid nitrogen

NASA Technical Reports Server (NTRS)

Cuan, Winston M.; Schwartz, Sidney H.

1988-01-01

Results are presented for a preliminary experiment involving saturated pool boiling at 1 atm from rotating 2 and 3 in. diameter spheres which were immersed in liquid nitrogen (LN2). Additional results are presented for a stationary, 2 inch diameter sphere, quenched in LN2, which were obtained utilizing a more versatile and complete experimental apparatus that will eventually be used for additional rotating sphere experiments. The speed for the rotational tests was varied from 0 to 10,000 rpm. The stationary experiments parametrically varied pressure and subcooling levels from 0 to 600 psig and from 0 to 50 F, respectively. During the rotational tests, a high speed photographic analysis was undertaken to measure the thickness of the vapor film surrounding the sphere. The average Nusselt number over the cooling period was plotted against the rotational Reynolds number. Stationary sphere results included local boiling heat transfer coefficients at different latitudinal locations, for various pressure and subcooling levels.

G-38, 39 and 40: An artist's exploration of space. [using the space environment to create orbiting sphere configurations

NASA Technical Reports Server (NTRS)

Mcshane, J. W.; Coursen, C. D.

1984-01-01

Three experiments are described which use space processing technology in the formation of and coating of bubbles and spheres to be orbited as sculptures visible from Earth. In one experiment, a 22,000 m1 sphere is to ride into orbit containing a 15 psi Earth atmosphere. Once in orbit, a controller directs a valve to open, linking the sphere to a vacuum of space. Technologies used in the fabrication of these art forms include vacuum film deposition and large bubble formation in the space environment.

Formation of aggregated nanoparticle spheres through femtosecond laser surface processing

NASA Astrophysics Data System (ADS)

Tsubaki, Alfred T.; Koten, Mark A.; Lucis, Michael J.; Zuhlke, Craig; Ianno, Natale; Shield, Jeffrey E.; Alexander, Dennis R.

2017-10-01

A detailed structural and chemical analysis of a class of self-organized surface structures, termed aggregated nanoparticle spheres (AN-spheres), created using femtosecond laser surface processing (FLSP) on silicon, silicon carbide, and aluminum is reported in this paper. AN-spheres are spherical microstructures that are 20-100 μm in diameter and are composed entirely of nanoparticles produced during femtosecond laser ablation of material. AN-spheres have an onion-like layered morphology resulting from the build-up of nanoparticle layers over multiple passes of the laser beam. The material properties and chemical composition of the AN-spheres are presented in this paper based on scanning electron microscopy (SEM), focused ion beam (FIB) milling, transmission electron microscopy (TEM), and energy dispersive x-ray spectroscopy (EDX) analysis. There is a distinct difference in the density of nanoparticles between concentric rings of the onion-like morphology of the AN-sphere. Layers of high-density form when the laser sinters nanoparticles together and low-density layers form when nanoparticles redeposit while the laser ablates areas surrounding the AN-sphere. The dynamic nature of femtosecond laser ablation creates a variety of nanoparticles that make-up the AN-spheres including Si/C core-shell, nanoparticles that directly fragmented from the base material, nanoparticles with carbon shells that retarded oxidation, and amorphous, fully oxidized nanoparticles.

UC Irvine CHRS RainSphere - a new user friendly tool for analyzing global remotely sensed rainfall estimates

NASA Astrophysics Data System (ADS)

Nguyen, P.; Sorooshian, S.; Hsu, K. L.; Gao, X.; AghaKouchak, A.; Braithwaite, D.; Thorstensen, A. R.; Ashouri, H.; Tran, H.; Huynh, P.; Palacios, T.

2016-12-01

Center for Hydrometeorology and Remote Sensing (CHRS), University of California, Irvine has recently developed the CHRS RainSphere (hosted at http://rainsphere.eng.uci.edu) for scientific studies and applications using the Precipitation Estimation from Remotely Sensed Information using Artificial Neural Networks - Climate Data Record (PERSIANN-CDR, Ashouri et al. 2015). PERSIANN-CDR is a long-term (33+ years) high-resolution (daily, 0.25 degree) global satellite precipitation dataset which is useful for climatological studies and water resources applications. CHRS RainSphere has functionalities allowing users to visualize and query spatiotemporal statistics of global daily satellite precipitation for the past three decades. With a couple of mouse-clicks, users can easily obtain a report of time series, spatial plots, and basic trend analysis of rainfall for various spatial domains of interest such as location, watershed, basin, political division and country for yearly, monthly, monthly by year or daily. Mann-Kendall test is implemented on CHRS RainSphere for statistically investigating whether there is a significant increasing/decreasing rainfall trend at a location or over a specific spatial domain. CHRS RainSphere has a range of capabilities and should appeal to a broad spectrum of users including climate scientists, water resources managers and planners, and engineers. CHRS RainSphere can also be a useful educational tool for the general public to investigate climate change and variability. The video tutorial on CHRS RainSphere is available at https://www.youtube.com/watch?v=eI2-f88iGlY&feature=youtu.be. A demonstration of CHRS RainSphere will be included in the presentation.

Contact mechanics for coated spheres that includes the transition from weak to strong adhesion

DOE PAGES

Reedy, Earl David

2007-09-01

Recently published results for a rigid spherical indenter contacting a thin, linear elastic coating on a rigid planar substrate have been extended to include the case of two contacting spheres, where each sphere is rigid and coated with a thin, linear elastic material. This is done by using an appropriately chosen effective radius and coating modulus. Finally, the earlier work has also been extended to provide analytical results that span the transition between the previously derived Derjaguin–Müller–Toporov (DMT)-like (work of adhesion/coating-modulus ratio is small) and Johnson–Kendall–Roberts (JKR)-like (work of adhesion/coating-modulus ratio is large) limits.

MRS3D: 3D Spherical Wavelet Transform on the Sphere

NASA Astrophysics Data System (ADS)

Lanusse, F.; Rassat, A.; Starck, J.-L.

2011-12-01

Future cosmological surveys will provide 3D large scale structure maps with large sky coverage, for which a 3D Spherical Fourier-Bessel (SFB) analysis is natural. Wavelets are particularly well-suited to the analysis and denoising of cosmological data, but a spherical 3D isotropic wavelet transform does not currently exist to analyse spherical 3D data. We present a new fast Discrete Spherical Fourier-Bessel Transform (DSFBT) based on both a discrete Bessel Transform and the HEALPIX angular pixelisation scheme. We tested the 3D wavelet transform and as a toy-application, applied a denoising algorithm in wavelet space to the Virgo large box cosmological simulations and found we can successfully remove noise without much loss to the large scale structure. The new spherical 3D isotropic wavelet transform, called MRS3D, is ideally suited to analysing and denoising future 3D spherical cosmological surveys; it uses a novel discrete spherical Fourier-Bessel Transform. MRS3D is based on two packages, IDL and Healpix and can be used only if these two packages have been installed.

19 CFR 158.3 - Allowance for lost or missing packages included in an entry summary.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 19 Customs Duties 2 2012-04-01 2012-04-01 false Allowance for lost or missing packages included in..., DAMAGED, ABANDONED, OR EXPORTED Lost or Missing Packages and Deficiencies in Contents of Packages § 158.3 Allowance for lost or missing packages included in an entry summary. Allowance shall be made in the...

19 CFR 158.3 - Allowance for lost or missing packages included in an entry summary.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 19 Customs Duties 2 2013-04-01 2013-04-01 false Allowance for lost or missing packages included in..., DAMAGED, ABANDONED, OR EXPORTED Lost or Missing Packages and Deficiencies in Contents of Packages § 158.3 Allowance for lost or missing packages included in an entry summary. Allowance shall be made in the...

19 CFR 158.3 - Allowance for lost or missing packages included in an entry summary.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 19 Customs Duties 2 2010-04-01 2010-04-01 false Allowance for lost or missing packages included in..., DAMAGED, ABANDONED, OR EXPORTED Lost or Missing Packages and Deficiencies in Contents of Packages § 158.3 Allowance for lost or missing packages included in an entry summary. Allowance shall be made in the...

19 CFR 158.3 - Allowance for lost or missing packages included in an entry summary.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 19 Customs Duties 2 2011-04-01 2011-04-01 false Allowance for lost or missing packages included in..., DAMAGED, ABANDONED, OR EXPORTED Lost or Missing Packages and Deficiencies in Contents of Packages § 158.3 Allowance for lost or missing packages included in an entry summary. Allowance shall be made in the...

19 CFR 158.3 - Allowance for lost or missing packages included in an entry summary.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 19 Customs Duties 2 2014-04-01 2014-04-01 false Allowance for lost or missing packages included in..., DAMAGED, ABANDONED, OR EXPORTED Lost or Missing Packages and Deficiencies in Contents of Packages § 158.3 Allowance for lost or missing packages included in an entry summary. Allowance shall be made in the...

PLOT3D- DRAWING THREE DIMENSIONAL SURFACES

NASA Technical Reports Server (NTRS)

Canright, R. B.

1994-01-01

PLOT3D is a package of programs to draw three-dimensional surfaces of the form z = f(x,y). The function f and the boundary values for x and y are the input to PLOT3D. The surface thus defined may be drawn after arbitrary rotations. However, it is designed to draw only functions in rectangular coordinates expressed explicitly in the above form. It cannot, for example, draw a sphere. Output is by off-line incremental plotter or online microfilm recorder. This package, unlike other packages, will plot any function of the form z = f(x,y) and portrays continuous and bounded functions of two independent variables. With curve fitting; however, it can draw experimental data and pictures which cannot be expressed in the above form. The method used is division into a uniform rectangular grid of the given x and y ranges. The values of the supplied function at the grid points (x, y) are calculated and stored; this defines the surface. The surface is portrayed by connecting successive (y,z) points with straight-line segments for each x value on the grid and, in turn, connecting successive (x,z) points for each fixed y value on the grid. These lines are then projected by parallel projection onto the fixed yz-plane for plotting. This program has been implemented on the IBM 360/67 with on-line CDC microfilm recorder.

A Review of Patents for the Smart Packaging of Meat and Muscle-based Food Products.

PubMed

Holman, Benjamin; Kerry, Joseph P; Hopkins, David L

2017-10-31

Meat packaging once acted primarily as an inert barrier to protect its contents against contamination and this function has shifted. Packaging now includes complementary functions that improve product quality, longevity and customer/retail appeal. The devices and methods applied to achieve these functions may be categorised as smart packaging, which includes intelligent packaging, devised to monitor and communicate packaged content status, and active packaging, to provide passive adjustment of in-pack conditions from its interactions with the packaged meat. Smart packaging examples already available from recent patents include antimicrobial and antioxidant packaging coatings and inserts; sensors or indicators that identify spoilage and freshness; functional engineering customisations; improvements to packaging integrity; leak or tamper detectors; and, environmentally sustainable options. Together, these inventions respond to industry and customer demands for meat packaging and are therefore the focus of this review, in which we discuss their applications and limitations in meat packaging. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

The mold integration method for the calculation of the crystal-fluid interfacial free energy from simulations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Espinosa, J. R.; Vega, C.; Sanz, E.

2014-10-07

The interfacial free energy between a crystal and a fluid, γ{sub cf}, is a highly relevant parameter in phenomena such as wetting or crystal nucleation and growth. Due to the difficulty of measuring γ{sub cf} experimentally, computer simulations are often used to study the crystal-fluid interface. Here, we present a novel simulation methodology for the calculation of γ{sub cf}. The methodology consists in using a mold composed of potential energy wells to induce the formation of a crystal slab in the fluid at coexistence conditions. This induction is done along a reversible pathway along which the free energy difference betweenmore » the initial and the final states is obtained by means of thermodynamic integration. The structure of the mold is given by that of the crystal lattice planes, which allows to easily obtain the free energy for different crystal orientations. The method is validated by calculating γ{sub cf} for previously studied systems, namely, the hard spheres and the Lennard-Jones systems. Our results for the latter show that the method is accurate enough to deal with the anisotropy of γ{sub cf} with respect to the crystal orientation. We also calculate γ{sub cf} for a recently proposed continuous version of the hard sphere potential and obtain the same γ{sub cf} as for the pure hard sphere system. The method can be implemented both in Monte Carlo and Molecular Dynamics. In fact, we show that it can be easily used in combination with the popular Molecular Dynamics package GROMACS.« less

Exact evaluation of the depletion force between nanospheres in a polydisperse polymer fluid under Θ conditions.

PubMed

Wang, Haiqiang; Woodward, Clifford E; Forsman, Jan

2014-05-21

We analyze a system consisting of two spherical particles immersed in a polydispersed polymer solution under theta conditions. An exact theory is developed to describe the potential of mean force between the spheres for the case where the polymer molecular weight dispersity is described by the Schulz-Flory distribution. Exact results can be derived for the protein regime, where the sphere radius (R(s)) is small compared to the average radius of gyration of the polymer (R(g)). Numerical results are relatively easily obtained in the cases where the sphere radius is increased. We find that even when q = R(g)/R(s) ⪆ 10, then the use of a monopole expansion for the polymer end-point distribution about the spheres is sufficient. For even larger spheres q ≈ 1, accuracy is maintained by including a dipolar correction. The implications of these findings on generating a full many-body effective interaction for a collection of N spheres imbedded in the polymer solution are discussed.

Characterization of maximally random jammed sphere packings. III. Transport and electromagnetic properties via correlation functions

NASA Astrophysics Data System (ADS)

Klatt, Michael A.; Torquato, Salvatore

2018-01-01

In the first two papers of this series, we characterized the structure of maximally random jammed (MRJ) sphere packings across length scales by computing a variety of different correlation functions, spectral functions, hole probabilities, and local density fluctuations. From the remarkable structural features of the MRJ packings, especially its disordered hyperuniformity, exceptional physical properties can be expected. Here we employ these structural descriptors to estimate effective transport and electromagnetic properties via rigorous bounds, exact expansions, and accurate analytical approximation formulas. These property formulas include interfacial bounds as well as universal scaling laws for the mean survival time and the fluid permeability. We also estimate the principal relaxation time associated with Brownian motion among perfectly absorbing traps. For the propagation of electromagnetic waves in the long-wavelength limit, we show that a dispersion of dielectric MRJ spheres within a matrix of another dielectric material forms, to a very good approximation, a dissipationless disordered and isotropic two-phase medium for any phase dielectric contrast ratio. We compare the effective properties of the MRJ sphere packings to those of overlapping spheres, equilibrium hard-sphere packings, and lattices of hard spheres. Moreover, we generalize results to micro- and macroscopically anisotropic packings of spheroids with tensorial effective properties. The analytic bounds predict the qualitative trend in the physical properties associated with these structures, which provides guidance to more time-consuming simulations and experiments. They especially provide impetus for experiments to design materials with unique bulk properties resulting from hyperuniformity, including structural-color and color-sensing applications.

NARMER-1: a photon point-kernel code with build-up factors

NASA Astrophysics Data System (ADS)

Visonneau, Thierry; Pangault, Laurence; Malouch, Fadhel; Malvagi, Fausto; Dolci, Florence

2017-09-01

This paper presents an overview of NARMER-1, the new generation of photon point-kernel code developed by the Reactor Studies and Applied Mathematics Unit (SERMA) at CEA Saclay Center. After a short introduction giving some history points and the current context of development of the code, the paper exposes the principles implemented in the calculation, the physical quantities computed and surveys the generic features: programming language, computer platforms, geometry package, sources description, etc. Moreover, specific and recent features are also detailed: exclusion sphere, tetrahedral meshes, parallel operations. Then some points about verification and validation are presented. Finally we present some tools that can help the user for operations like visualization and pre-treatment.

Output-increasing, protective cover for a solar cell

DOEpatents

Hammerbacher, Milfred D.

1995-11-21

A flexible cover (14) for a flexible solar cell (12) protects the cell from the ambient and increases the cell's efficiency. The cell(12)includes silicon spheres (16) held in a flexible aluminum sheet matrix (20,22). The cover (14) is a flexible, protective layer (60) of light-transparent material having a relatively flat upper, free surface (64) and an irregular opposed surface (66). The irregular surface (66) includes first portions (68) which conform to the polar regions (31R) of the spheres (16) and second convex (72) or concave (90) portions (72 or 90) which define spaces (78) in conjunction with the reflective surface (20T) of one aluminum sheet (20). Without the cover (14) light (50) falling on the surface (20T) between the spheres (16) is wasted, that is, it does not fall on a sphere (16). The surfaces of the second portions are non-parallel to the direction of the otherwise wasted light (50), which fact, together with a selected relationship between the refractive indices of the cover and the spaces, result in sufficient diffraction of the otherwise wasted light (50) so that about 25% of it is reflected from the surface (20T) onto a sphere (16).

Effects on RCS of a perfect electromagnetic conductor sphere in the presence of anisotropic plasma layer

NASA Astrophysics Data System (ADS)

Ghaffar, A.; Hussan, M. M.; Illahi, A.; Alkanhal, Majeed A. S.; Ur Rehman, Sajjad; Naz, M. Y.

2018-01-01

Effects on RCS of perfect electromagnetic conductor (PEMC) sphere by coating with anisotropic plasma layer are studied in this paper. The incident, scattered and transmitted electromagnetic fields are expanded in term of spherical vector wave functions using extended classical theory of scattering. Co and cross-polarized scattered field coefficients are obtained at the interface of free space-anisotropic plasma and at anisotropic plasma-PEMC sphere core by scattering matrices method. The presented analytical expressions are general for any perfect conducting sphere (PMC, PEC, or PEMC) with general anisotropic/isotropic material coatings that include plasma and metamaterials. The behavior of the forward and backscattered radar cross section of PEMC sphere with the variation of the magnetic field strength, incident frequency, plasma density, and effective collision frequency for the co-polarized and the cross polarized fields are investigated. It is also observed from the obtained results that anisotropic layer on PEMC sphere shows reciprocal behavior as compared to isotopic plasma layer on PEMC sphere. The comparisons of the numerical results of the presented analytical expressions with available results of some special cases show the correctness of the analysis.

Lunar surface engineering properties experiment definition. Volume 2: Mechanics of rolling sphere-soil slope interaction

NASA Technical Reports Server (NTRS)

Hovland, H. J.; Mitchell, J. K.

1971-01-01

The soil deformation mode under the action of a rolling sphere (boulder) was determined, and a theory based on actual soil failure mechanism was developed which provides a remote reconnaissance technique for study of soil conditions using boulder track observations. The failure mechanism was investigated by using models and by testing an instrumented spherical wheel. The wheel was specifically designed to measure contact pressure, but it also provided information on the failure mechanism. Further tests included rolling some 200 spheres down sand slopes. Films were taken of the rolling spheres, and the tracks were measured. Implications of the results and reevaluation of the lunar boulder tracks are discussed.

Ball assisted device for analytical surface sampling

DOEpatents

ElNaggar, Mariam S; Van Berkel, Gary J; Covey, Thomas R

2015-11-03

A system for sampling a surface includes a sampling probe having a housing and a socket, and a rolling sampling sphere within the socket. The housing has a sampling fluid supply conduit and a sampling fluid exhaust conduit. The sampling fluid supply conduit supplies sampling fluid to the sampling sphere. The sampling fluid exhaust conduit has an inlet opening for receiving sampling fluid carried from the surface by the sampling sphere. A surface sampling probe and a method for sampling a surface are also disclosed.

Variable leak gas source

DOEpatents

Henderson, Timothy M.; Wuttke, Gilbert H.

1977-01-01

A variable leak gas source and a method for obtaining the same which includes filling a quantity of hollow glass micro-spheres with a gas, storing said quantity in a confined chamber having a controllable outlet, heating said chamber above room temperature, and controlling the temperature of said chamber to control the quantity of gas passing out of said controllable outlet. Individual gas filled spheres may be utilized for calibration purposes by breaking a sphere having a known quantity of a known gas to calibrate a gas detection apparatus.

Synthesis of highly uniform Cu2O spheres by a two-step approach and their assembly to form photonic crystals with a brilliant color.

PubMed

Su, Xin; Chang, Jie; Wu, Suli; Tang, Bingtao; Zhang, Shufen

2016-03-21

Monodisperse semiconductor colloidal spheres with a high refractive index hold great potential for building photonic crystals with a strong band gap, but the difficulty in separating the nucleation and growth processes makes it challenging to prepare highly uniform semiconductor colloidal spheres. Herein, real monodisperse Cu2O spheres were prepared via a hot-injection & heating-up two-step method using diethylene glycol as a milder reducing agent. The diameter of the as prepared Cu2O spheres can be tuned from 90 nm to 190 nm precisely. The SEM images reveal that the obtained Cu2O spheres have a narrow size distribution, which permits their self-assembly to form photonic crystals. The effects of precursor concentration and heating rates on the size and morphology of the Cu2O spheres were investigated in detail. The results indicate that the key points of the method include the burst nucleation to form seeds at a high temperature followed by rapid cooling to prevent agglomeration, and appropriate precursor concentration as well as a moderate growth rate during the further growth process. Importantly, photonic crystal films exhibiting a brilliant structural color were fabricated with the obtained monodisperse Cu2O spheres as building blocks, proving the possibility of making photonic crystals with a strong band gap. The developed method was also successfully applied to prepare monodisperse CdS spheres with diameters in the range from 110 nm to 210 nm.

Structural and Acoustic Damping Characteristics of Polyimide Microspheres

NASA Technical Reports Server (NTRS)

Palumbo, Daniel L.; Park, Junhong

2005-01-01

A broad range of tests have been performed to evaluate the capability of tiny lightweight polyimide spheres to reduce sound and vibration. The types of testing includes impedance tube measurement of propagation constant, sound power insertion loss for single and double wall systems, particle frame wave characterization and beam vibration reduction. The tests were performed using spheres made of two types of polyimide and with varying diameter. Baseline results were established using common noise reduction treatment materials such as fiberglass and foam. The spheres were difficult to test due to their inherent mobility. Most tests required some adaptation to contain the spheres. One test returned obvious non-linear behavior, a result which has come to be expected for treatments of this type. The polyimide spheres are found to be a competent treatment for both sound and vibration energy with the reservation that more work needs to be done to better characterize the non-linear behavior.

Apparatus and methods for controlling electron microscope stages

DOE Office of Scientific and Technical Information (OSTI.GOV)

Duden, Thomas

Methods and apparatus for generating an image of a specimen with a microscope (e.g., TEM) are disclosed. In one aspect, the microscope may generally include a beam generator, a stage, a detector, and an image generator. A plurality of crystal parameters, which describe a plurality of properties of a crystal sample, are received. In a display associated with the microscope, an interactive control sphere based at least in part on the received crystal parameters and that is rotatable by a user to different sphere orientations is presented. The sphere includes a plurality of stage coordinates that correspond to a pluralitymore » of positions of the stage and a plurality of crystallographic pole coordinates that correspond to a plurality of polar orientations of the crystal sample. Movement of the sphere causes movement of the stage, wherein the stage coordinates move in conjunction with the crystallographic coordinates represented by pole positions so as to show a relationship between stage positions and the pole positions.« less

The influence of size and charge of chitosan/polyglutamic acid hollow spheres on cellular internalization, viability and blood compatibility.

PubMed

Dash, Biraja C; Réthoré, Gildas; Monaghan, Michael; Fitzgerald, Kathleen; Gallagher, William; Pandit, Abhay

2010-11-01

Polymeric hollow spheres can be tailored as efficient carriers of various therapeutic molecules due to their tunable properties. However, the entry of these synthetic vehicles into cells, their cell viability and blood compatibility depend on their physical and chemical properties e.g. size, surface charge. Herein, we report the effect of size and surface charge on cell viability and cellular internalization behaviour and their effect on various blood components using chitosan/polyglutamic acid hollow spheres as a model system. Negatively charged chitosan/polyglutamic acid hollow spheres of various sizes 100, 300, 500 and 1000 nm were fabricated using a template based method and covalently surface modified using linear polyethylene glycol and methoxyethanol amine to create a gradient of surface charge from negative to neutrally charged spheres respectively. The results here suggest that both size and surface charge have a significant influence on the sphere's behaviour, most prominently on haemolysis, platelet activation, plasma recalcification time, cell viability and internalization over time. Additionally, cellular internalization behaviour and viability was found to vary with different cell types. These results are in agreement with those of inorganic spheres and liposomes, and can serve as guidelines for tailoring polymeric solid spheres for specific desired applications in biological and pharmaceutical fields, including the design of nanometer to submicron-sized delivery vehicles. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

Multilayered microelectronic device package with an integral window

DOEpatents

Peterson, Kenneth A.; Watson, Robert D.

2003-01-01

An apparatus for packaging of microelectronic devices is disclosed, wherein the package includes an integral window. The microelectronic device can be a semiconductor chip, a CCD chip, a CMOS chip, a VCSEL chip, a laser diode, a MEMS device, or a IMEMS device. The package can comprise, for example, a cofired ceramic frame or body. The package has an internal stepped structure made of a plurality of plates, with apertures, which are patterned with metallized conductive circuit traces. The microelectronic device can be flip-chip bonded on the plate to these traces, and oriented so that the light-sensitive side is optically accessible through the window. A cover lid can be attached to the opposite side of the package. The result is a compact, low-profile package, having an integral window that can be hermetically-sealed. The package body can be formed by low-temperature cofired ceramic (LTCC) or high-temperature cofired ceramic (HTCC) multilayer processes with the window being simultaneously joined (e.g. cofired) to the package body during LTCC or HTCC processing. Multiple chips can be located within a single package, according to some embodiments. The cover lid can include a window. The apparatus is particularly suited for packaging of MEMS devices, since the number of handling steps is greatly reduced, thereby reducing the potential for contamination. The integral window can further include a lens for optically transforming light passing through the window. The package can include an array of binary optic lenslets made integral with the window. The package can include an electrically-switched optical modulator, such as a lithium niobate window attached to the package, for providing a very fast electrically-operated shutter.

Food packaging history and innovations.

PubMed

Risch, Sara J

2009-09-23

Food packaging has evolved from simply a container to hold food to something today that can play an active role in food quality. Many packages are still simply containers, but they have properties that have been developed to protect the food. These include barriers to oxygen, moisture, and flavors. Active packaging, or that which plays an active role in food quality, includes some microwave packaging as well as packaging that has absorbers built in to remove oxygen from the atmosphere surrounding the product or to provide antimicrobials to the surface of the food. Packaging has allowed access to many foods year-round that otherwise could not be preserved. It is interesting to note that some packages have actually allowed the creation of new categories in the supermarket. Examples include microwave popcorn and fresh-cut produce, which owe their existence to the unique packaging that has been developed.

Nanoscale Hollow Spheres: Microemulsion-Based Synthesis, Structural Characterization and Container-Type Functionality

PubMed Central

Gröger, Henriette; Kind, Christian; Leidinger, Peter; Roming, Marcus; Feldmann, Claus

2010-01-01

A wide variety of nanoscale hollow spheres can be obtained via a microemulsion approach. This includes oxides (e.g., ZnO, TiO2, SnO2, AlO(OH), La(OH)3), sulfides (e.g., Cu2S, CuS) as well as elemental metals (e.g., Ag, Au). All hollow spheres are realized with outer diameters of 10−60 nm, an inner cavity size of 2−30 nm and a wall thickness of 2−15 nm. The microemulsion approach allows modification of the composition of the hollow spheres, fine-tuning their diameter and encapsulation of various ingredients inside the resulting “nanocontainers”. This review summarizes the experimental conditions of synthesis and compares them to other methods of preparing hollow spheres. Moreover, the structural characterization and selected properties of the as-prepared hollow spheres are discussed. The latter is especially focused on container-functionalities with the encapsulation of inorganic salts (e.g., KSCN, K2S2O8, KF), biomolecules/bioactive molecules (e.g., phenylalanine, quercetin, nicotinic acid) and fluorescent dyes (e.g., rhodamine, riboflavin) as representative examples. PMID:28883333

Development and Performance of a Filter Radiometer Monitor System for Integrating Sphere Sources

NASA Technical Reports Server (NTRS)

Ding, Leibo; Kowalewski, Matthew G.; Cooper, John W.; Smith, GIlbert R.; Barnes, Robert A.; Waluschka, Eugene; Butler, James J.

2011-01-01

The NASA Goddard Space Flight Center (GSFC) Radiometric Calibration Laboratory (RCL) maintains several large integrating sphere sources covering the visible to the shortwave infrared wavelength range. Two critical, functional requirements of an integrating sphere source are short and long-term operational stability and repeatability. Monitoring the source is essential in determining the origin of systemic errors, thus increasing confidence in source performance and quantifying repeatability. If monitor data falls outside the established parameters, this could be an indication that the source requires maintenance or re-calibration against the National Institute of Science and Technology (NIST) irradiance standard. The GSFC RCL has developed a Filter Radiometer Monitoring System (FRMS) to continuously monitor the performance of its integrating sphere calibration sources in the 400 to 2400nm region. Sphere output change mechanisms include lamp aging, coating (e.g. BaSO4) deterioration, and ambient water vapor level. The Filter Radiometer Monitor System (FRMS) wavelength bands are selected to quantify changes caused by these mechanisms. The FRMS design and operation are presented, as well as data from monitoring four of the RCL s integrating sphere sources.

Some Early Optics: Classical and Medieval. Experiment No. 6.

ERIC Educational Resources Information Center

Devons, Samuel

Information related to the history of optics with emphasis on the classical and medieval periods is presented. Notes are included on experiments dealing with refraction at a plane interface between two media; refraction by transparent spheres; light, color, and reflection by transparent spheres. (Author/SA)

The OLI Radiometric Scale Realization Round Robin Measurement Campaign

NASA Technical Reports Server (NTRS)

Cutlip, Hansford; Cole,Jerold; Johnson, B. Carol; Maxwell, Stephen; Markham, Brian; Ong, Lawrence; Hom, Milton; Biggar, Stuart

2011-01-01

A round robin radiometric scale realization was performed at the Ball Aerospace Radiometric Calibration Laboratory in January/February 2011 in support of the Operational Land Imager (OLI) Program. Participants included Ball Aerospace, NIST, NASA Goddard Space Flight Center, and the University of Arizona. The eight day campaign included multiple observations of three integrating sphere sources by nine radiometers. The objective of the campaign was to validate the radiance calibration uncertainty ascribed to the integrating sphere used to calibrate the OLI instrument. The instrument level calibration source uncertainty was validated by quatnifying: (1) the long term stability of the NIST calibrated radiance artifact, (2) the responsivity scale of the Ball Aerospace transfer radiometer and (3) the operational characteristics of the large integrating sphere.

Packaging Concerns/Techniques for Large Devices

NASA Technical Reports Server (NTRS)

Sampson, Michael J.

2009-01-01

This slide presentation reviews packaging challenges and options for electronic parts. The presentation includes information about non-hermetic packages, space challenges for packaging and complex package variations.

Close-packed monolayer self-assembly of silica nanospheres assisted by infrared irradiation

NASA Astrophysics Data System (ADS)

Minh, Nguyen Van; Hue, Nguyen Thi; Lien, Nghiem Thi Ha; Hoang, Chu Manh

2018-01-01

In this paper, we report on a fast and cost-effective drop coating technique for the self-assembly of silica nano-spheres from a mono-dispersed colloidal suspension into close-packed monolayer (CMP) on hydrophilic single-crystal silicon substrate. The technique includes the self-assembly of silica nano-spheres on slanted silicon substrate and infrared irradiation during evaporation process of the coated droplet. The influence of the substrate slant angle and infrared irradiation on the formation of silica nano-sphere monolayer is investigated. This achievement is promising for various applications, such as a mask layer for nano-sphere lithography that is employed for producing fundamental elements in photonics, plasmonics, and solar cell. [Figure not available: see fulltext.

Methods and considerations to determine sphere center from terrestrial laser scanner point cloud data

NASA Astrophysics Data System (ADS)

Rachakonda, Prem; Muralikrishnan, Bala; Cournoyer, Luc; Cheok, Geraldine; Lee, Vincent; Shilling, Meghan; Sawyer, Daniel

2017-10-01

The Dimensional Metrology Group at the National Institute of Standards and Technology is performing research to support the development of documentary standards within the ASTM E57 committee. This committee is addressing the point-to-point performance evaluation of a subclass of 3D imaging systems called terrestrial laser scanners (TLSs), which are laser-based and use a spherical coordinate system. This paper discusses the usage of sphere targets for this effort, and methods to minimize the errors due to the determination of their centers. The key contributions of this paper include methods to segment sphere data from a TLS point cloud, and the study of some of the factors that influence the determination of sphere centers.

A DIM model for sodium cluster-ions interacting with a charged conducting sphere

NASA Astrophysics Data System (ADS)

Kuntz, P. J.

A diatomics-in-molecules (DIM) model for the energy, shape and charge distribution of metal cluster ions in the presence of a charged insulated conducting sphere is presented. The electrostatic interaction between the sphere and the cluster-ion is introduced in a self-consistent manner which allows the sphere to be polarized by the ion and the ion by the sphere. This interaction appears in the diagonal elements of the model Hamiltonian matrix in such a way that the lowest eigenvalue includes the correct electrostatic energy for the charge distribution in the ground state. The model is applied to the calculation of fusion barriers for Na+2 and Na+3 ions. When both the charge distribution and the geometric configuration of the cluster-ion are allowed to relax freely, the energy as a function of distance from the sphere is nearly the same as that calculated from the electrostatic energy alone, which implies that details of the molecular structure of the cluster-ion can be neglected in calculating fusion barriers from charge polarization alone. That the fusion barriers lie sufficiently far away from the sphere so that the molecule does not dissociate under the influence of the Coulomb interaction confirms that it is meaningful to speak of two separate entities at the barrier position.

Characterising exoplanet atmospheres with SPHERE: the HR 8799 system with Exo-REM and NEMESIS

NASA Astrophysics Data System (ADS)

Baudino, J.-L.; Bonnefoy, M.; Vigan, A.; Irwin, P. J.

2017-12-01

The characterisation of the exoplanets evolved recently thanks to the beginning of the second generation of direct imaging instruments, especially with SPHERE. The resolution and wavelength range available currently give access to an increase of accuracy and on the number of physical parameters that can be constrain. One of the first target of SPHERE was the HR 8799 system. The four planets was characterised using four different forward models including Exo-REM. We complete this paper buy using NEMESIS, a retrieval code.

AIRS Maps from Space Processing Software

NASA Technical Reports Server (NTRS)

Thompson, Charles K.; Licata, Stephen J.

2012-01-01

This software package processes Atmospheric Infrared Sounder (AIRS) Level 2 swath standard product geophysical parameters, and generates global, colorized, annotated maps. It automatically generates daily and multi-day averaged colorized and annotated maps of various AIRS Level 2 swath geophysical parameters. It also generates AIRS input data sets for Eyes on Earth, Puffer-sphere, and Magic Planet. This program is tailored to AIRS Level 2 data products. It re-projects data into 1/4-degree grids that can be combined and averaged for any number of days. The software scales and colorizes global grids utilizing AIRS-specific color tables, and annotates images with title and color bar. This software can be tailored for use with other swath data products for the purposes of visualization.

Evaluation of an alternative shielding materials for F-127 transport package

NASA Astrophysics Data System (ADS)

Gual, Maritza R.; Mesquita, Amir Z.; Pereira, Cláubia

2018-03-01

Lead is used as radiation shielding material for the Nordion's F-127 source shipping container is used for transport and storage of the GammaBeam -127's cobalt-60 source of the Nuclear Technology Development Center (CDTN) located in Belo Horizonte, Brazil. As an alternative, Th, Tl and WC have been evaluated as radiation shielding material. The goal is to check their behavior regarding shielding and dosing. Monte Carlo MCNPX code is used for the simulations. In the MCNPX calculation was used one cylinder as exclusion surface instead one sphere. Validation of MCNPX gamma doses calculations was carried out through comparison with experimental measurements. The results show that tungsten carbide WC is better shielding material for γ-ray than lead shielding.

A new integrating sphere design for spectral radiant flux determination of light-emitting diodes

NASA Astrophysics Data System (ADS)

Hanselaer, P.; Keppens, A.; Forment, S.; Ryckaert, W. R.; Deconinck, G.

2009-09-01

Light-emitting diode (LED) technology is developing very quickly and may be considered an alternative for traditional light sources. However, at this moment, manufacturers and end users of LEDs are facing a rather basic but major problem. The lack of standardization regarding optical and electrical characterization of LEDs appears to compromise a successful implementation. In particular, numbers quoted for the luminous flux, and consequently for the efficacy of LEDs, are very sensitive data because they are used to impress and push the LED market. In this paper, the most was made of the typical hemispherical radiation of high-power LEDs to increase the accuracy of the flux determination using a custom-made integrating sphere. Recently developed measurement techniques such as the use of an external spectral irradiance standard and an optimized spectral irradiance detection head are combined with a very particular port geometry and a minimized baffle area. This results in a uniform spatial response distribution function (SRDF), which guarantees an accurate radiant and luminous flux determination, irrespective of the spatial intensity distribution of the LED package or luminaire. The effect of the directional response of the detector head on the SRDF has been explored. Measurements on LED devices with and without external optics are presented, illustrating the possibilities of the measurement setup.

Quantification of Focal Outflow Enhancement Using Differential Canalograms

PubMed Central

Loewen, Ralitsa T.; Brown, Eric N.; Scott, Gordon; Parikh, Hardik; Schuman, Joel S.; Loewen, Nils A.

2016-01-01

Purpose To quantify regional changes of conventional outflow caused by ab interno trabeculectomy (AIT). Methods Gonioscopic, plasma-mediated AIT was established in enucleated pig eyes. We developed a program to automatically quantify outflow changes (R, package eye-canalogram, github.com) using a fluorescent tracer reperfusion technique. Trabecular meshwork (TM) ablation was demonstrated with fluorescent spheres in six eyes before formal outflow quantification with two-dye reperfusion canalograms in six additional eyes. Eyes were perfused with a central, intracameral needle at 15 mm Hg. Canalograms and histology were correlated for each eye. Results The pig eye provided a model with high similarity to AIT in human patients. Histology indicated ablation of TM and unroofing of most Schlemm's canal segments. Spheres highlighted additional circumferential and radial outflow beyond the immediate area of ablation. Differential canalograms showed that AIT caused an increase of outflow of 17 ± 5-fold inferonasally, 14 ± 3-fold superonasally, and also an increase in the opposite quadrants with a 2 ± 1-fold increase superotemporally, and 3 ± 3 inferotemporally. Perilimbal specific flow image analysis showed an accelerated nasal filling with an additional perilimbal flow direction into adjacent quadrants. Conclusions A quantitative, differential canalography technique was developed that allows us to quantify supraphysiological outflow enhancement by AIT. PMID:27227352

Fluorescent/magnetic micro/nano-spheres based on quantum dots and/or magnetic nanoparticles: preparation, properties, and their applications in cancer studies

NASA Astrophysics Data System (ADS)

Wen, Cong-Ying; Xie, Hai-Yan; Zhang, Zhi-Ling; Wu, Ling-Ling; Hu, Jiao; Tang, Man; Wu, Min; Pang, Dai-Wen

2016-06-01

The study of cancer is of great significance to human survival and development, due to the fact that cancer has become one of the greatest threats to human health. In recent years, the rapid progress of nanoscience and nanotechnology has brought new and bright opportunities to this field. In particular, the applications of quantum dots (QDs) and magnetic nanoparticles (MNPs) have greatly promoted early diagnosis and effective therapy of cancer. In this review, we focus on fluorescent/magnetic micro/nano-spheres based on QDs and/or MNPs (we may call them ``nanoparticle-sphere (NP-sphere) composites'') from their preparation to their bio-application in cancer research. Firstly, we outline and compare the main four kinds of methods for fabricating NP-sphere composites, including their design principles, operation processes, and characteristics (merits and limitations). The NP-sphere composites successfully inherit the unique fluorescence or magnetic properties of QDs or MNPs. Moreover, compared with the nanoparticles (NPs) alone, the NP-sphere composites show superior properties, which are also discussed in this review. Then, we summarize their recent applications in cancer research from three aspects, that is: separation and enrichment of target tumor cells or biomarkers; cancer diagnosis mainly through medical imaging or tumor biomarker detection; and cancer therapy via targeted drug delivery systems. Finally, we provide some perspectives on the future challenges and development trends of the NP-sphere composites.

Clinician accessible tools for GUI computational models of transcranial electrical stimulation: BONSAI and SPHERES.

PubMed

Truong, Dennis Q; Hüber, Mathias; Xie, Xihe; Datta, Abhishek; Rahman, Asif; Parra, Lucas C; Dmochowski, Jacek P; Bikson, Marom

2014-01-01

Computational models of brain current flow during transcranial electrical stimulation (tES), including transcranial direct current stimulation (tDCS) and transcranial alternating current stimulation (tACS), are increasingly used to understand and optimize clinical trials. We propose that broad dissemination requires a simple graphical user interface (GUI) software that allows users to explore and design montages in real-time, based on their own clinical/experimental experience and objectives. We introduce two complimentary open-source platforms for this purpose: BONSAI and SPHERES. BONSAI is a web (cloud) based application (available at neuralengr.com/bonsai) that can be accessed through any flash-supported browser interface. SPHERES (available at neuralengr.com/spheres) is a stand-alone GUI application that allow consideration of arbitrary montages on a concentric sphere model by leveraging an analytical solution. These open-source tES modeling platforms are designed go be upgraded and enhanced. Trade-offs between open-access approaches that balance ease of access, speed, and flexibility are discussed. Copyright © 2014 Elsevier Inc. All rights reserved.

Wet-Chemical Preparation of TiO2-Based Composites with Different Morphologies and Photocatalytic Properties

PubMed Central

Xiang, Liqin; Zhao, Xiaopeng

2017-01-01

TiO2-based composites have been paid significant attention in the photocatalysis field. The size, crystallinity and nanomorphology of TiO2 materials have an important effect on the photocatalytic efficiency. The synthesis and photocatalytic activity of TiO2-based materials have been widely investigated in past decades. Based on our group’s research works on TiO2 materials, this review introduces several methods for the fabrication of TiO2, rare-earth-doped TiO2 and noble-metal-decorated TiO2 particles with different morphologies. We focused on the preparation and the formation mechanism of TiO2-based materials with unique structures including spheres, hollow spheres, porous spheres, hollow porous spheres and urchin-like spheres. The photocatalytical activity of urchin-like TiO2, noble metal nanoparticle-decorated 3D (three-dimensional) urchin-like TiO2 and bimetallic core/shell nanoparticle-decorated urchin-like hierarchical TiO2 are briefly discussed. PMID:28991208

Application of identifying transmission spheres for spherical surface testing

NASA Astrophysics Data System (ADS)

Han, Christopher B.; Ye, Xin; Li, Xueyuan; Wang, Quanzhao; Tang, Shouhong; Han, Sen

2017-06-01

We developed a new application on Microsoft Foundation Classes (MFC) to identify correct transmission spheres (TS) for Spherical Surface Testing (SST). Spherical surfaces are important optical surfaces, and the wide application and high production rate of spherical surfaces necessitates an accurate and highly reliable measuring device. A Fizeau Interferometer is an appropriate tool for SST due to its subnanometer accuracy. It measures the contour of a spherical surface using a common path, which is insensitive to the surrounding circumstances. The Fizeau Interferometer transmits a wide laser beam, creating interference fringes from re-converging light from the transmission sphere and the test surface. To make a successful measurement, the application calculates and determines the appropriate transmission sphere for the test surface. There are 3 main inputs from the test surfaces that are utilized to determine the optimal sizes and F-numbers of the transmission spheres: (1) the curvatures (concave or convex), (2) the Radii of Curvature (ROC), and (3) the aperture sizes. The application will firstly calculate the F-numbers (i.e. ROC divided by aperture) of the test surface, secondly determine the correct aperture size of a convex surface, thirdly verify that the ROC of the test surface must be shorter than the reference surface's ROC of the transmission sphere, and lastly calculate the percentage of area that the test surface will be measured. However, the amount of interferometers and transmission spheres should be optimized when measuring large spherical surfaces to avoid requiring a large amount of interferometers and transmission spheres for each test surface. Current measuring practices involve tedious and potentially inaccurate calculations. This smart application eliminates human calculation errors, optimizes the selection of transmission spheres (including the least number required) and interferometer sizes, and increases efficiency.

Enrichment and characterization of cancer stem cells from a human non-small cell lung cancer cell line.

PubMed

Zhao, Changhong; Setrerrahmane, Sarra; Xu, Hanmei

2015-10-01

Tumor cells from the same origin comprise different cell populations. Among them, cancer stem cells (CSCs) have higher tumorigenicity. It is necessary to enrich CSCs to determine an effective way to suppress and eliminate them. In the present study, using the non-adhesive culture system, tumor spheres were successfully generated from human A549 non-small cell lung cancer (NSCLC) cell line within 2 weeks. Compared to A549 adherent cells, sphere cells had a higher self-renewal ability and increased resistance to cytotoxic drugs. Sphere cells were more invasive and expressed stem cell markers including octamer‑binding transcription factor 4 (Oct4) and sex-determining region Y-box 2 (Sox2) at high levels. CD133, a disputed marker of lung CSCs, was also upregulated. Tumor sphere cells showed higher tumorigenic ability in vivo, indicating that more CSCs were enriched in the sphere cells. More blood vessels were formed in the tumor generated by sphere cells suggesting the interaction between CSCs and blood vessel. A reliable model of enriching CSCs from the human A549 NSCLC cell line was established that was simple and cost-effective compared to other methods.

NORSTAR Project: Norfolk public schools student team for acoustical research

NASA Technical Reports Server (NTRS)

Fortunato, Ronald C.

1987-01-01

Development of the NORSTAR (Norfolk Public Student Team for Acoustical Research) Project includes the definition, design, fabrication, testing, analysis, and publishing the results of an acoustical experiment. The student-run program is based on a space flight organization similar to the Viking Project. The experiment will measure the scattering transfer of momentum from a sound field to spheres in a liquid medium. It is hoped that the experimental results will shed light on a difficult physics problem - the difference in scattering cross section (the overall effect of the sound wave scattering) for solid spheres and hollow spheres of differing wall thicknesses.

User's manual for the coupled rotor/airframe vibration analysis graphic package

NASA Technical Reports Server (NTRS)

Studwell, R. E.

1982-01-01

User instructions for a graphics package for coupled rotor/airframe vibration analysis are presented. Responses to plot package messages which the user must make to activate plot package operations and options are described. Installation instructions required to set up the program on the CDC system are included. The plot package overlay structure and subroutines which have to be modified for the CDC system are also described. Operating instructions for CDC applications are included.

Quantitative Comparison of PET and Bremsstrahlung SPECT for Imaging the In Vivo Yttrium-90 Microsphere Distribution after Liver Radioembolization

PubMed Central

Elschot, Mattijs; Vermolen, Bart J.; Lam, Marnix G. E. H.; de Keizer, Bart; van den Bosch, Maurice A. A. J.; de Jong, Hugo W. A. M.

2013-01-01

Background After yttrium-90 (90Y) microsphere radioembolization (RE), evaluation of extrahepatic activity and liver dosimetry is typically performed on 90Y Bremsstrahlung SPECT images. Since these images demonstrate a low quantitative accuracy, 90Y PET has been suggested as an alternative. The aim of this study is to quantitatively compare SPECT and state-of-the-art PET on the ability to detect small accumulations of 90Y and on the accuracy of liver dosimetry. Methodology/Principal Findings SPECT/CT and PET/CT phantom data were acquired using several acquisition and reconstruction protocols, including resolution recovery and Time-Of-Flight (TOF) PET. Image contrast and noise were compared using a torso-shaped phantom containing six hot spheres of various sizes. The ability to detect extra- and intrahepatic accumulations of activity was tested by quantitative evaluation of the visibility and unique detectability of the phantom hot spheres. Image-based dose estimates of the phantom were compared to the true dose. For clinical illustration, the SPECT and PET-based estimated liver dose distributions of five RE patients were compared. At equal noise level, PET showed higher contrast recovery coefficients than SPECT. The highest contrast recovery coefficients were obtained with TOF PET reconstruction including resolution recovery. All six spheres were consistently visible on SPECT and PET images, but PET was able to uniquely detect smaller spheres than SPECT. TOF PET-based estimates of the dose in the phantom spheres were more accurate than SPECT-based dose estimates, with underestimations ranging from 45% (10-mm sphere) to 11% (37-mm sphere) for PET, and 75% to 58% for SPECT, respectively. The differences between TOF PET and SPECT dose-estimates were supported by the patient data. Conclusions/Significance In this study we quantitatively demonstrated that the image quality of state-of-the-art PET is superior over Bremsstrahlung SPECT for the assessment of the 90Y microsphere distribution after radioembolization. PMID:23405207

Radar Imaging of Spheres in 3D using MUSIC

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chambers, D H; Berryman, J G

2003-01-21

We have shown that multiple spheres can be imaged by linear and planar EM arrays using only one component of polarization. The imaging approach involves calculating the SVD of the scattering response matrix, selecting a subset of singular values that represents noise, and evaluating the MUSIC functional. The noise threshold applied to the spectrum of singular values for optimal performance is typically around 1%. The resulting signal subspace includes more than one singular value per sphere. The presence of reflections from the ground improves height localization, even for a linear array parallel to the ground. However, the interference between directmore » and reflected energy modulates the field, creating periodic nulls that can obscure targets in typical images. These nulls are largely eliminated by normalizing the MUSIC functional with the broadside beam pattern of the array. The resulting images show excellent localization for 1 and 2 spheres. The performance for the 3 sphere configurations are complicated by shadowing effects and the greater range of the 3rd sphere in case 2. Two of the three spheres are easily located by MUSIC but the third is difficult to distinguish from other local maxima of the complex imaging functional. Improvement is seen when the linear array is replace with a planar array, which increases the effective aperture height. Further analysis of the singular values and their relationship to modes of scattering from the spheres, as well as better ways to exploit polarization, should improve performance. Work along these lines is currently being pursued by the authors.« less

Paramilitary Organizations in Germany from 1871-1945

DTIC Science & Technology

2014-03-01

56 4. Waffen -SS...in all spheres of German life, including the academic sphere.”91 The NPEA would become a recruitment base for future Waffen -SS officers under...master race of Aryan Germans. In addition to the Germanization aims, Himmler set out to expand the Waffen -SS during World War II and use them to purge

Depletion zones and crystallography on pinched spheres

NASA Astrophysics Data System (ADS)

Chen, Jingyuan; Xing, Xiangjun; Yao, Zhenwei

2018-03-01

Understanding the interplay between ordered structures and substrate curvature is an interesting problem with versatile applications, including functionalization of charged supramolecular surfaces and modern microfluidic technologies. In this work, we investigate the two-dimensional packing structures of charged particles confined on a pinched sphere. By continuously pinching the sphere, we observe cleavage of elongated scars into pleats, proliferation of disclinations, and subsequently, emergence of a depletion zone at the negatively curved waist that is completely void of particles. We systematically study the geometrics and energetics of the depletion zone, and reveal its physical origin as a finite size effect, due to the interplay between Coulomb repulsion and concave geometry of the pinched sphere. These results further our understanding of crystallography on curved surfaces, and have implications in design and manipulation of charged, deformable interfaces in various applications.

Numerical simulation of a shear-thinning fluid through packed spheres

NASA Astrophysics Data System (ADS)

Liu, Hai Long; Moon, Jong Sin; Hwang, Wook Ryol

2012-12-01

Flow behaviors of a non-Newtonian fluid in spherical microstructures have been studied by a direct numerical simulation. A shear-thinning (power-law) fluid through both regular and randomly packed spheres has been numerically investigated in a representative unit cell with the tri-periodic boundary condition, employing a rigorous three-dimensional finite-element scheme combined with fictitious-domain mortar-element methods. The present scheme has been validated for the classical spherical packing problems with literatures. The flow mobility of regular packing structures, including simple cubic (SC), body-centered cubic (BCC), face-centered cubic (FCC), as well as randomly packed spheres, has been investigated quantitatively by considering the amount of shear-thinning, the pressure gradient and the porosity as parameters. Furthermore, the mechanism leading to the main flow path in a highly shear-thinning fluid through randomly packed spheres has been discussed.

Spherical Lu2O2S:Eu3+ micro/nano-structure: Controlled synthesis and luminescence properties

NASA Astrophysics Data System (ADS)

Zhang, Bowen; Zou, Haifeng; Dai, Yunzhi; Guan, Hongxia; Song, Yanhua; Zheng, Keyan; Zhou, Xiuqing; Shi, Zhan; Sheng, Ye

2017-02-01

Monodisperse and uniform Lu2O2S:Eu3+ luminescent spheres have been successfully synthesized through a facile hydrothermal method followed by a subsequent calcination process. The sizes of the spheres can be tuned in the range of 65 nm-295 nm by only changing the pH value of the system. It is indicated that the luminescence properties of the spherical phosphors were strongly influenced by size of the spheres. Such a size-sensitive luminescence property was interpreted from the structures of the spheres, including the degree of crystallinity, band gap energy, crystal field symmetry around Eu3+. We expected that this study not only can provide important information for size-controlled synthesis of spherical phosphors, but also can give a reference for exploration of size-dependent luminescence.

Optical rotation of levitated spheres in high vacuum

NASA Astrophysics Data System (ADS)

Monteiro, Fernando; Ghosh, Sumita; van Assendelft, Elizabeth C.; Moore, David C.

2018-05-01

A circularly polarized laser beam is used to levitate and control the rotation of microspheres in high vacuum. At low pressure, rotation frequencies as high as 6 MHz are observed for birefringent vaterite spheres, limited by centrifugal stresses. Due to the extremely low damping in high vacuum, the controlled optical rotation of amorphous SiO2 spheres is also observed at rates above several MHz. At 10-7 mbar, a damping time of 6 ×104 s is measured for a 10 -μ m -diam SiO2 sphere. No additional damping mechanisms are observed above gas damping, indicating that even longer damping times may be possible with operation at lower pressure. The controlled optical rotation of microspheres at MHz frequencies with low damping, including for materials that are not intrinsically birefringent, provides a tool for performing precision measurements using optically levitated systems.

MEG/EEG Source Reconstruction, Statistical Evaluation, and Visualization with NUTMEG

PubMed Central

Dalal, Sarang S.; Zumer, Johanna M.; Guggisberg, Adrian G.; Trumpis, Michael; Wong, Daniel D. E.; Sekihara, Kensuke; Nagarajan, Srikantan S.

2011-01-01

NUTMEG is a source analysis toolbox geared towards cognitive neuroscience researchers using MEG and EEG, including intracranial recordings. Evoked and unaveraged data can be imported to the toolbox for source analysis in either the time or time-frequency domains. NUTMEG offers several variants of adaptive beamformers, probabilistic reconstruction algorithms, as well as minimum-norm techniques to generate functional maps of spatiotemporal neural source activity. Lead fields can be calculated from single and overlapping sphere head models or imported from other software. Group averages and statistics can be calculated as well. In addition to data analysis tools, NUTMEG provides a unique and intuitive graphical interface for visualization of results. Source analyses can be superimposed onto a structural MRI or headshape to provide a convenient visual correspondence to anatomy. These results can also be navigated interactively, with the spatial maps and source time series or spectrogram linked accordingly. Animations can be generated to view the evolution of neural activity over time. NUTMEG can also display brain renderings and perform spatial normalization of functional maps using SPM's engine. As a MATLAB package, the end user may easily link with other toolboxes or add customized functions. PMID:21437174

MEG/EEG source reconstruction, statistical evaluation, and visualization with NUTMEG.

PubMed

Dalal, Sarang S; Zumer, Johanna M; Guggisberg, Adrian G; Trumpis, Michael; Wong, Daniel D E; Sekihara, Kensuke; Nagarajan, Srikantan S

2011-01-01

NUTMEG is a source analysis toolbox geared towards cognitive neuroscience researchers using MEG and EEG, including intracranial recordings. Evoked and unaveraged data can be imported to the toolbox for source analysis in either the time or time-frequency domains. NUTMEG offers several variants of adaptive beamformers, probabilistic reconstruction algorithms, as well as minimum-norm techniques to generate functional maps of spatiotemporal neural source activity. Lead fields can be calculated from single and overlapping sphere head models or imported from other software. Group averages and statistics can be calculated as well. In addition to data analysis tools, NUTMEG provides a unique and intuitive graphical interface for visualization of results. Source analyses can be superimposed onto a structural MRI or headshape to provide a convenient visual correspondence to anatomy. These results can also be navigated interactively, with the spatial maps and source time series or spectrogram linked accordingly. Animations can be generated to view the evolution of neural activity over time. NUTMEG can also display brain renderings and perform spatial normalization of functional maps using SPM's engine. As a MATLAB package, the end user may easily link with other toolboxes or add customized functions.

In Vitro Analysis of Breast Cancer Cell Line Tumourspheres and Primary Human Breast Epithelia Mammospheres Demonstrates Inter- and Intrasphere Heterogeneity

PubMed Central

Vargas, Ana Cristina; Keith, Patricia; Reid, Lynne; Wockner, Leesa; Amiri, Marjan Askarian; Sarkar, Debina; Simpson, Peter T.; Clarke, Catherine; Schmidt, Chris W.; Reynolds, Brent A.

2013-01-01

Mammosphere and breast tumoursphere culture have gained popularity as in vitro assays for propagating and analysing normal and cancer stem cells. Whether the spheres derived from different sources or parent cultures themselves are indeed single entities enriched in stem/progenitor cells compared to other culture formats has not been fully determined. We surveyed sphere-forming capacity across 26 breast cell lines, immunophenotyped spheres from six luminal- and basal-like lines by immunohistochemistry and flow cytometry and compared clonogenicity between sphere, adherent and matrigel culture formats using in vitro functional assays. Analyses revealed morphological and molecular intra- and inter-sphere heterogeneity, consistent with adherent parental cell line phenotypes. Flow cytometry showed sphere culture does not universally enrich for markers previously associated with stem cell phenotypes, although we found some cell-line specific changes between sphere and adherent formats. Sphere-forming efficiency was significantly lower than adherent or matrigel clonogenicity and constant over serial passage. Surprisingly, self-renewal capacity of sphere-derived cells was similar/lower than other culture formats. We observed significant correlation between long-term-proliferating-cell symmetric division rates in sphere and adherent cultures, suggesting functional overlap between the compartments sustaining them. Experiments with normal primary human mammary epithelia, including sorted luminal (MUC1+) and basal/myoepithelial (CD10+) cells revealed distinct luminal-like, basal-like and mesenchymal entities amongst primary mammospheres. Morphological and colony-forming-cell assay data suggested mammosphere culture may enrich for a luminal progenitor phenotype, or induce reversion/relaxation of the basal/mesenchymal in vitro selection occurring with adherent culture. Overall, cell line tumourspheres and primary mammospheres are not homogenous entities enriched for stem cells, suggesting a more cautious approach to interpreting data from these assays and careful consideration of its limitations. Sphere culture may represent an alternative 3-dimensional culture system which rather than universally ‘enriching’ for stem cells, has utility as one of a suite of functional assays that provide a read-out of progenitor activity. PMID:23750209

Resonance scattering of a dielectric sphere illuminated by electromagnetic Bessel non-diffracting (vortex) beams with arbitrary incidence and selective polarizations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mitri, F.G., E-mail: F.G.Mitri@ieee.org; Li, R.X., E-mail: rxli@mail.xidian.edu.cn; Collaborative Innovation Center of Information Sensing and Understanding, Xidian University, Xi’an 710071

A complete description of vector Bessel (vortex) beams in the context of the generalized Lorenz–Mie theory (GLMT) for the electromagnetic (EM) resonance scattering by a dielectric sphere is presented, using the method of separation of variables and the subtraction of a non-resonant background (corresponding to a perfectly conducting sphere of the same size) from the standard Mie scattering coefficients. Unlike the conventional results of standard optical radiation, the resonance scattering of a dielectric sphere in air in the field of EM Bessel beams is examined and demonstrated with particular emphasis on the EM field’s polarization and beam order (or topologicalmore » charge). Linear, circular, radial, azimuthal polarizations as well as unpolarized Bessel vortex beams are considered. The conditions required for the resonance scattering are analyzed, stemming from the vectorial description of the EM field using the angular spectrum decomposition, the derivation of the beam-shape coefficients (BSCs) using the integral localized approximation (ILA) and Neumann–Graf’s addition theorem, and the determination of the scattering coefficients of the sphere using Debye series. In contrast with the standard scattering theory, the resonance method presented here allows the quantitative description of the scattering using Debye series by separating diffraction effects from the external and internal reflections from the sphere. Furthermore, the analysis is extended to include rainbow formation in Bessel beams and the derivation of a generalized formula for the deviation angle of high-order rainbows. Potential applications for this analysis include Bessel beam-based laser imaging spectroscopy, atom cooling and quantum optics, electromagnetic instrumentation and profilometry, optical tweezers and tractor beams, to name a few emerging areas of research.« less

Densest local sphere-packing diversity. II. Application to three dimensions

NASA Astrophysics Data System (ADS)

Hopkins, Adam B.; Stillinger, Frank H.; Torquato, Salvatore

2011-01-01

The densest local packings of N three-dimensional identical nonoverlapping spheres within a radius Rmin(N) of a fixed central sphere of the same size are obtained for selected values of N up to N=1054. In the predecessor to this paper [A. B. Hopkins, F. H. Stillinger, and S. Torquato, Phys. Rev. EPLEEE81063-651X10.1103/PhysRevE.81.041305 81, 041305 (2010)], we described our method for finding the putative densest packings of N spheres in d-dimensional Euclidean space Rd and presented those packings in R2 for values of N up to N=348. Here we analyze the properties and characteristics of the densest local packings in R3 and employ knowledge of the Rmin(N), using methods applicable in any d, to construct both a realizability condition for pair correlation functions of sphere packings and an upper bound on the maximal density of infinite sphere packings. In R3, we find wide variability in the densest local packings, including a multitude of packing symmetries such as perfect tetrahedral and imperfect icosahedral symmetry. We compare the densest local packings of N spheres near a central sphere to minimal-energy configurations of N+1 points interacting with short-range repulsive and long-range attractive pair potentials, e.g., 12-6 Lennard-Jones, and find that they are in general completely different, a result that has possible implications for nucleation theory. We also compare the densest local packings to finite subsets of stacking variants of the densest infinite packings in R3 (the Barlow packings) and find that the densest local packings are almost always most similar as measured by a similarity metric, to the subsets of Barlow packings with the smallest number of coordination shells measured about a single central sphere, e.g., a subset of the fcc Barlow packing. Additionally, we observe that the densest local packings are dominated by the dense arrangement of spheres with centers at distance Rmin(N). In particular, we find two “maracas” packings at N=77 and N=93, each consisting of a few unjammed spheres free to rattle within a “husk” composed of the maximal number of spheres that can be packed with centers at respective Rmin(N).

Enteric coated spheres produced by extrusion/spheronization provide effective gastric protection and efficient release of live therapeutic bacteria.

PubMed

de Barros, João M S; Lechner, Tabea; Charalampopoulos, Dimitrios; Khutoryanskiy, Vitaliy V; Edwards, Alexander D

2015-09-30

We present a novel but simple enteric coated sphere formulation containing probiotic bacteria (Lactobacillus casei). Oral delivery of live bacterial cells (LBC) requires live cells to survive firstly manufacturing processes and secondly GI microbicidal defenses including gastric acid. We incorporated live L. casei directly in the granulation liquid, followed by granulation, extrusion, spheronization, drying and spray coating to produce dried live probiotic spheres. A blend of MCC, calcium-crosslinked alginate, and lactose was developed that gave improved live cell survival during manufacturing, and gave excellent protection from gastric acid plus rapid release in intestinal conditions. No significant loss of viability was observed in all steps except drying, which resulted in approximately 1 log loss of viable cells. Eudragit coating was used to protect dried live cells from acid, and microcrystalline cellulose (MCC) was combined with sodium alginate to achieve efficient sphere disintegration leading to rapid and complete bacterial cell release in intestinal conditions. Viability and release of L. casei was evaluated in vitro in simulated GI conditions. Uncoated spheres gave partial acid protection, but enteric coated spheres effectively protected dried probiotic LBC from acid for 2h, and subsequently released all viable cells within 1h of transfer into simulated intestinal fluid. Copyright © 2015 Elsevier B.V. All rights reserved.

New Mexico Play Fairway Analysis: Particle Tracking ArcGIS Map Packages

DOE Data Explorer

Jeff Pepin

2015-11-15

These are map packages used to visualize geochemical particle-tracking analysis results in ArcGIS. It includes individual map packages for several regions of New Mexico including: Acoma, Rincon, Gila, Las Cruces, Socorro and Truth or Consequences.

Packaging Technologies for 500C SiC Electronics and Sensors

NASA Technical Reports Server (NTRS)

Chen, Liang-Yu

2013-01-01

Various SiC electronics and sensors are currently under development for applications in 500C high temperature environments such as hot sections of aerospace engines and the surface of Venus. In order to conduct long-term test and eventually commercialize these SiC devices, compatible packaging technologies for the SiC electronics and sensors are required. This presentation reviews packaging technologies developed for 500C SiC electronics and sensors to address both component and subsystem level packaging needs for high temperature environments. The packaging system for high temperature SiC electronics includes ceramic chip-level packages, ceramic printed circuit boards (PCBs), and edge-connectors. High temperature durable die-attach and precious metal wire-bonding are used in the chip-level packaging process. A high temperature sensor package is specifically designed to address high temperature micro-fabricated capacitive pressure sensors for high differential pressure environments. This presentation describes development of these electronics and sensor packaging technologies, including some testing results of SiC electronics and capacitive pressure sensors using these packaging technologies.

A novel methodology to model the cooling processes of packed horticultural produce using 3D shape models

NASA Astrophysics Data System (ADS)

Gruyters, Willem; Verboven, Pieter; Rogge, Seppe; Vanmaercke, Simon; Ramon, Herman; Nicolai, Bart

2017-10-01

Freshly harvested horticultural produce require a proper temperature management to maintain their high economic value. Towards this end, low temperature storage is of crucial importance to maintain a high product quality. Optimizing both the package design of packed produce and the different steps in the postharvest cold chain can be achieved by numerical modelling of the relevant transport phenomena. This work presents a novel methodology to accurately model both the random filling of produce in a package and the subsequent cooling process. First, a cultivar-specific database of more than 100 realistic CAD models of apple and pear fruit is built with a validated geometrical 3D shape model generator. To have an accurate representation of a realistic picking season, the model generator also takes into account the biological variability of the produce shape. Next, a discrete element model (DEM) randomly chooses surface meshed bodies from the database to simulate the gravitational filling process of produce in a box or bin, using actual mechanical properties of the fruit. A computational fluid dynamics (CFD) model is then developed with the final stacking arrangement of the produce to study the cooling efficiency of packages under several conditions and configurations. Here, a typical precooling operation is simulated to demonstrate the large differences between using actual 3D shapes of the fruit and an equivalent spheres approach that simplifies the problem drastically. From this study, it is concluded that using a simplified representation of the actual fruit shape may lead to a severe overestimation of the cooling behaviour.

Directional spectral emissivity measurement system

NASA Technical Reports Server (NTRS)

Halyo, Nesim (Inventor); Pandey, Dhirendra K. (Inventor)

1992-01-01

Apparatus and process for determining the emissivity of a test specimen including an integrated sphere having two concentric walls with a coolant circulating therebetween, and disposed within a chamber which may be under ambient, vacuum or inert gas conditions. A reference sample is disposed within the sphere with a monochromatic light source in optical alignment therewith. A pyrometer is in optical alignment with the test sample for obtaining continuous test sample temperature measurements during a test. An arcuate slit port is provided through the spaced concentric walls of the integrating sphere with a movable monochromatic light source extending through and movable along the arcuate slit port. A detector system extends through the integrating sphere for continuously detecting an integrated signal indicative of all radiation within its field of view, as a function of the emissivity of the test specimen at various temperatures and various angle position of the monochromatic light source. A furnace for heating the test sample to approximately 3000 K. and control mechanism for transferring the heated sample from the furnace to the test sample port in the integrating sphere is also contained within the chamber.

Microelectronic device package with an integral window

DOEpatents

Peterson, Kenneth A.; Watson, Robert D.

2002-01-01

An apparatus for packaging of microelectronic devices, including an integral window. The microelectronic device can be a semiconductor chip, a CCD chip, a CMOS chip, a VCSEL chip, a laser diode, a MEMS device, or a IMEMS device. The package can include a cofired ceramic frame or body. The package can have an internal stepped structure made of one or more plates, with apertures, which are patterned with metallized conductive circuit traces. The microelectronic device can be flip-chip bonded on the plate to these traces, and oriented so that the light-sensitive side is optically accessible through the window. A cover lid can be attached to the opposite side of the package. The result is a compact, low-profile package, having an integral window that can be hermetically-sealed. The package body can be formed by low-temperature cofired ceramic (LTCC) or high-temperature cofired ceramic (HTCC) multilayer processes with the window being simultaneously joined (e.g. cofired) to the package body during LTCC or HTCC processing. Multiple chips can be located within a single package. The cover lid can include a window. The apparatus is particularly suited for packaging of MEMS devices, since the number of handling steps is greatly reduced, thereby reducing the potential for contamination.

Packaging and Embedded Electronics for the Next Generation

NASA Technical Reports Server (NTRS)

Sampson, Michael J.

2010-01-01

This viewgraph presentation describes examples of electronic packaging that protects an electronic element from handling, contamination, shock, vibration and light penetration. The use of Hermetic and non-hermetic packaging is also discussed. The topics include: 1) What is Electronic Packaging? 2) Why Package Electronic Parts? 3) Evolution of Packaging; 4) General Packaging Discussion; 5) Advanced non-hermetic packages; 6) Discussion of Hermeticity; 7) The Class Y Concept and Possible Extensions; 8) Embedded Technologies; and 9) NEPP Activities.

Aristotle of Stagira (384-322 BC)

NASA Astrophysics Data System (ADS)

Murdin, P.

2001-07-01

Aristotle was a Greek philosopher and scientist, born in Stagira. Aristotle's lectures were compiled into 150 volumes, including Physics, Metaphysics and De Caelo et Mundo (On the Heavens and Earth), in which he accepted the heavenly spheres of eudoxus, thought the Earth to be spherical and imagined a perfectly spherical, unchanging universe of spheres centred on the Earth and carrying the planets...

Scanning ion-conductance and atomic force microscope with specialized sphere-shaped nanopippettes

NASA Astrophysics Data System (ADS)

Zhukov, M. V.; Sapozhnikov, I. D.; Golubok, A. O.; Chubinskiy-Nadezhdin, V. I.; Komissarenko, F. E.; Lukashenko, S. Y.

2017-11-01

A scanning ion-conductance microscope was designed on the basis of scanning probe microscope NanoTutor. The optimal parameters of nanopipettes fabrication were found according to scanning electron microscopy diagnostics, current-distance I (Z) and current-voltage characteristics. A comparison of images of test objects, including biological samples, was carried out in the modes of optical microscopy, atomic force microscopy and scanning ion-conductance microscopy. Sphere-shaped nanopippettes probes were developed and tested to increase the stability of pipettes, reduce invasiveness and improve image quality of atomic force microscopy in tapping mode. The efficiency of sphere-shaped nanopippettes is shown.

An adaptive multiblock high-order finite-volume method for solving the shallow-water equations on the sphere

DOE PAGES

McCorquodale, Peter; Ullrich, Paul; Johansen, Hans; ...

2015-09-04

We present a high-order finite-volume approach for solving the shallow-water equations on the sphere, using multiblock grids on the cubed-sphere. This approach combines a Runge--Kutta time discretization with a fourth-order accurate spatial discretization, and includes adaptive mesh refinement and refinement in time. Results of tests show fourth-order convergence for the shallow-water equations as well as for advection in a highly deformational flow. Hierarchical adaptive mesh refinement allows solution error to be achieved that is comparable to that obtained with uniform resolution of the most refined level of the hierarchy, but with many fewer operations.

Test Control Center

NASA Image and Video Library

2000-10-25

At the test observation periscope in the Test Control Center exhibit in StenniSphere at the John C. Stennis Space Center in Hancock County, Miss., visitors can observe a test of a Space Shuttle Main Engine exactly as test engineers might see it during a real engine test. The Test Control Center exhibit exactly simulates not only the test control environment, but also the procedure of testing a rocket engine. Designed to entertain while educating, StenniSphere includes informative dispays and exhibits from NASA's lead center for rocket propulsion and remote sensing applications. StenniSphere is open free of charge from 9 a.m. to 5 p.m. daily.

Simulation-based Bayesian inference for latent traits of item response models: Introduction to the ltbayes package for R.

PubMed

Johnson, Timothy R; Kuhn, Kristine M

2015-12-01

This paper introduces the ltbayes package for R. This package includes a suite of functions for investigating the posterior distribution of latent traits of item response models. These include functions for simulating realizations from the posterior distribution, profiling the posterior density or likelihood function, calculation of posterior modes or means, Fisher information functions and observed information, and profile likelihood confidence intervals. Inferences can be based on individual response patterns or sets of response patterns such as sum scores. Functions are included for several common binary and polytomous item response models, but the package can also be used with user-specified models. This paper introduces some background and motivation for the package, and includes several detailed examples of its use.

The Effect of Lens Sphere and Cylinder Power on Residual Astigmatism and Its Resolution After Toric Intraocular Lens Implantation.

PubMed

Berdahl, John P; Hardten, David R; Kramer, Brent A; Potvin, Richard

2017-03-01

To analyze correlations between residual refractive cylinder (and its correction through lens reorientation) with the sphere and cylinder power of the toric intraocular lens (IOL) implanted. An online toric back-calculator (www.astigmatismfix.com) allows users to input toric IOL planning data, along with postoperative IOL orientation and refractive results; these data are used to determine the optimal orientation of the IOL to reduce refractive astigmatism. This was a retrospective data analysis; aggregate historical data were extracted from this calculator to investigate the relationship between residual refractive astigmatism and IOL cylinder and sphere power. A total of 12,812 records, 4,619 of which included IOL sphere power, were available for analysis. There was no significant effect of sphere power on residual refractive astigmatism (P = .25), but lower IOL cylinder powers were associated with significantly lower residual refractive astigmatism (P < .05). The difference between the intended and ideal orientation was higher in the lower IOL cylinder power groups (P < .01). Overcorrection of astigmatism was significantly more likely with higher IOL cylinder power (P < .01), but not with sphere power (P = .33). Reorientation to correct residual refractive cylinder to less than 0.50 diopters (D) was more successful with IOL cylinder powers of 1.50 D or less (P < .01); IOL sphere power had no apparent effect. There were significant effects of IOL cylinder power on residual refractive astigmatism, the difference between intended and ideal orientation, the likelihood of overcorrection, and the likelihood of astigmatism reduction with lens reorientation. IOL sphere power appeared to have no such effects. [J Refract Surg. 2017;33(3):157-162.]. Copyright 2017, SLACK Incorporated.

SPHERES tethered formation flight testbed: advancements in enabling NASA's SPECS mission

NASA Astrophysics Data System (ADS)

Chung, Soon-Jo; Adams, Danielle; Saenz-Otero, Alvar; Kong, Edmund; Miller, David W.; Leisawitz, David; Lorenzini, Enrico; Sell, Steve

2006-06-01

This paper reports on efforts to control a tethered formation flight spacecraft array for NASA's SPECS mission using the SPHERES test-bed developed by the MIT Space Systems Laboratory. Specifically, advances in methodology and experimental results realized since the 2005 SPIE paper are emphasized. These include a new test-bed setup with a reaction wheel assembly, a novel relative attitude measurement system using force torque sensors, and modeling of non-ideal tethers to account for tether vibration modes. The nonlinear equations of motion of multi-vehicle tethered spacecraft with elastic flexible tethers are derived from Lagrange's equations. The controllability analysis indicates that both array resizing and spin-up are fully controllable by the reaction wheels and the tether motor, thereby saving thruster fuel consumption. Based upon this analysis, linear and nonlinear controllers have been successfully implemented on the tethered SPHERES testbed, and tested at the NASA MSFC's flat floor facility using two and three SPHERES configurations.

IASI Radiance Data Assimilation in Local Ensemble Transform Kalman Filter

NASA Astrophysics Data System (ADS)

Cho, K.; Hyoung-Wook, C.; Jo, Y.

2016-12-01

Korea institute of Atmospheric Prediction Systems (KIAPS) is developing NWP model with data assimilation systems. Local Ensemble Transform Kalman Filter (LETKF) system, one of the data assimilation systems, has been developed for KIAPS Integrated Model (KIM) based on cubed-sphere grid and has successfully assimilated real data. LETKF data assimilation system has been extended to 4D- LETKF which considers time-evolving error covariance within assimilation window and IASI radiance data assimilation using KPOP (KIAPS package for observation processing) with RTTOV (Radiative Transfer for TOVS). The LETKF system is implementing semi operational prediction including conventional (sonde, aircraft) observation and AMSU-A (Advanced Microwave Sounding Unit-A) radiance data from April. Recently, the semi operational prediction system updated radiance observations including GPS-RO, AMV, IASI (Infrared Atmospheric Sounding Interferometer) data at July. A set of simulation of KIM with ne30np4 and 50 vertical levels (of top 0.3hPa) were carried out for short range forecast (10days) within semi operation prediction LETKF system with ensemble forecast 50 members. In order to only IASI impact, our experiments used only conventional and IAIS radiance data to same semi operational prediction set. We carried out sensitivity test for IAIS thinning method (3D and 4D). IASI observation number was increased by temporal (4D) thinning and the improvement of IASI radiance data impact on the forecast skill of model will expect.

Analysis of the Reference Systems of Modern Selenographic Systems

NASA Astrophysics Data System (ADS)

Nefedyev, Yuri; Petrova, Natalia; Andreev, Alexey; Demina, Natalya

2016-07-01

In this work analysis of the reference systems of modern selenographic systems was made. The center of the Moon's mass position relative to its center of figure was determined from the data of "Clementine" and "Kaguya" missions and "ULCN" and "KSC-1162" catalogues. The knowledge of the Moon's center of mass position relative to its center of figure is important for researches of the lunar origin, structure and evolution and in terms of precision solutions circumlunar navigation tasks. At the present this task is the most relevant and demanded for cosmic lunar missions.The expansions by spherical harmonics N=5 degree and order of the lunar function h (λ, β) using the package ASNI USTU were executed. Module of the expansion of the local area to surfaces to full sphere was used. The parameters of cosmic missions are given for comparison (SAI; Bills, Ferrari). The normalized coefficients from expansions for eight sources of hypsometric information are obtained: "Clementine" (N=40), "KSC-1162" (N=5), "Kiev" (N=5), "SAI" (N=10; Chuikova (1975)), "Bills, Ferrari", "Kaguya" (Selena, Japan mission), "ULCN" (The Unified Lunar Control Network 2005). The displacements of the lunar center of figure relative to the lunar center of the mass were defined from equations (Chuikova (1975)): Δ ξ = C_{11} √{3}, Δ η= S_{11} √{3}, Δ ζ = C_{10} √{3}, where ξ is the axis directed towards the Earth, η is equatorial axis directed perpendicularly to ξ , ζ is rotation axis of the Moon, C_{11} , S_{11} , C_{10} are the normalized amplitudes of the harmonics of the first order expansion of the relief. After that we considered: - mathematical models in the form of expansions in spherical functions - methods for estimating the model parameters; - information technology data processing. As a model describing the behavior of the relief on the lunar sphere is used the expansion of the height in a series of spherical harmonics (Sagitov (1979)) in the form of a regression model (Valeev (2001)). To obtain the expansions in spherical harmonics in order to create a digital model and determine estimations of the center of mass position of the Moon relative to its center of the figure required in the future was usedsoftware package ASSR "Sphere" (an automated system of scientific research).ASSR "Sphere" is intended to describe the distribution of various values of the parameters (topography, gravity, magnetic, and other types of potential fields) on the sphere and its parts which were measured in points with known coordinates. Using this bundled software one can generate models of the specificform,carry out forecasting in the form of cross-sections, contour, tone and three-dimensional representation of the distribution of characteristicsvalues. The formation of models is accompanied by estimation of their quality and diagnostic of adherence of least square method. After all we can conclude that the "KSC-1162" catalogue, which was obtained in the center of mass and principal axes of inertia of the Moon, has the closest agreement with the results of recent space missions.It should be noted that the correction of the first measurements of the "Clementine" mission data, which were obtained by the authors of the "ULCN 2005" catalogue, was apparently related to the data on the visible side of the Moon because the amplitudes and offsets for the ("KSC-1162" + "Clementine") option close to the results of the "ULCN 2005" optionbut not to"Clementine".The results of defining relative position of the lunar center of mass and center of figure in "KSC-1162"selenocentric catalogue gave some good agreement with modern space mission data. Work was supported by grants RFBR 15-02-01638-a, 16-32-60071-mol-dk-a and 16-02-00496-a.

A modular, energy-based approach to the development of nickel containing molecular electrocatalysts for hydrogen production and oxidation.

PubMed

Shaw, Wendy J; Helm, Monte L; DuBois, Daniel L

2013-01-01

This review discusses the development of molecular electrocatalysts for H2 production and oxidation based on nickel. A modular approach is used in which the structure of the catalyst is divided into first, second, and outer coordination spheres. The first coordination sphere consists of the ligands bound directly to the metal center, and this coordination sphere can be used to control such factors as the presence or absence of vacant coordination sites, redox potentials, hydride donor abilities and other important thermodynamic parameters. The second coordination sphere includes functional groups such as pendent acids or bases that can interact with bound substrates such as H2 molecules and hydride ligands, but that do not form strong bonds with the metal center. These functional groups can play diverse roles such as assisting the heterolytic cleavage of H2, controlling intra- and intermolecular proton transfer reactions, and providing a physical pathway for coupling proton and electron transfer reactions. By controlling both the hydride donor ability of the catalysts using the first coordination sphere and the proton donor abilities of the functional groups in the second coordination sphere, catalysts can be designed that are biased toward H2 production, oxidation, or bidirectional (catalyzing both H2 oxidation and production). The outer coordination sphere is defined as that portion of the catalytic system that is beyond the second coordination sphere. This coordination sphere can assist in the delivery of protons and electrons to and from the catalytically active site, thereby adding another important avenue for controlling catalytic activity. Many features of these simple catalytic systems are good models for enzymes, and these simple systems provide insights into enzyme function and reactivity that may be difficult to probe in enzymes. This article is part of a Special Issue entitled: Metals in Bioenergetics and Biomimetics Systems. Copyright © 2013 Elsevier B.V. All rights reserved.

Protection of microelectronic devices during packaging

DOEpatents

Peterson, Kenneth A.; Conley, William R.

2002-01-01

The present invention relates to a method of protecting a microelectronic device during device packaging, including the steps of applying a water-insoluble, protective coating to a sensitive area on the device; performing at least one packaging step; and then substantially removing the protective coating, preferably by dry plasma etching. The sensitive area can include a released MEMS element. The microelectronic device can be disposed on a wafer. The protective coating can be a vacuum vapor-deposited parylene polymer, silicon nitride, metal (e.g. aluminum or tungsten), a vapor deposited organic material, cynoacrylate, a carbon film, a self-assembled monolayered material, perfluoropolyether, hexamethyldisilazane, or perfluorodecanoic carboxylic acid, silicon dioxide, silicate glass, or combinations thereof. The present invention also relates to a method of packaging a microelectronic device, including: providing a microelectronic device having a sensitive area; applying a water-insoluble, protective coating to the sensitive area; providing a package; attaching the device to the package; electrically interconnecting the device to the package; and substantially removing the protective coating from the sensitive area.

Temporary coatings for protection of microelectronic devices during packaging

DOEpatents

Peterson, Kenneth A.; Conley, William R.

2005-01-18

The present invention relates to a method of protecting a microelectronic device during device packaging, including the steps of applying a water-insoluble, temporary protective coating to a sensitive area on the device; performing at least one packaging step; and then substantially removing the protective coating, preferably by dry plasma etching. The sensitive area can include a released MEMS element. The microelectronic device can be disposed on a wafer. The protective coating can be a vacuum vapor-deposited parylene polymer, silicon nitride, metal (e.g. aluminum or tungsten), a vapor deposited organic material, cynoacrylate, a carbon film, a self-assembled monolayered material, perfluoropolyether, hexamethyldisilazane, or perfluorodecanoic carboxylic acid, silicon dioxide, silicate glass, or combinations thereof. The present invention also relates to a method of packaging a microelectronic device, including: providing a microelectronic device having a sensitive area; applying a water-insoluble, protective coating to the sensitive area; providing a package; attaching the device to the package; electrically interconnecting the device to the package; and substantially removing the protective coating from the sensitive area.

21 CFR 516.165 - Records and reports.

Code of Federal Regulations, 2014 CFR

2014-04-01

... within 60 days thereafter. The report must contain data and information for the full reporting period..., include a summary of those changes and the holder's and distributor's current package labeling, including any package inserts. For large-size package labeling or large shipping cartons, submit a...

21 CFR 516.165 - Records and reports.

Code of Federal Regulations, 2012 CFR

2012-04-01

... within 60 days thereafter. The report must contain data and information for the full reporting period..., include a summary of those changes and the holder's and distributor's current package labeling, including any package inserts. For large-size package labeling or large shipping cartons, submit a...

Food packages for use on the Gemini 4 flight

NASA Technical Reports Server (NTRS)

1965-01-01

Food packages for use on the Gemini 4 flight. Packages include beef and gravy, peaches, strawberry cereal cubes and beef sandwiches. Water gun is used to reconstitute dehydrated food. Scissors are used to open the packages.

Optimal segmentation and packaging process

DOEpatents

Kostelnik, Kevin M.; Meservey, Richard H.; Landon, Mark D.

1999-01-01

A process for improving packaging efficiency uses three dimensional, computer simulated models with various optimization algorithms to determine the optimal segmentation process and packaging configurations based on constraints including container limitations. The present invention is applied to a process for decontaminating, decommissioning (D&D), and remediating a nuclear facility involving the segmentation and packaging of contaminated items in waste containers in order to minimize the number of cuts, maximize packaging density, and reduce worker radiation exposure. A three-dimensional, computer simulated, facility model of the contaminated items are created. The contaminated items are differentiated. The optimal location, orientation and sequence of the segmentation and packaging of the contaminated items is determined using the simulated model, the algorithms, and various constraints including container limitations. The cut locations and orientations are transposed to the simulated model. The contaminated items are actually segmented and packaged. The segmentation and packaging may be simulated beforehand. In addition, the contaminated items may be cataloged and recorded.

Initial Radiometric Calibration of the AWiFS using Vicarious Calibration Techniques

NASA Technical Reports Server (NTRS)

Pagnutti, Mary; Thome, Kurtis; Aaron, David; Leigh, Larry

2006-01-01

NASA SSC maintains four ASD FieldSpec FR spectroradiometers: 1) Laboratory transfer radiometers; 2) Ground surface reflectance for V&V field collection activities. Radiometric Calibration consists of a NIST-calibrated integrating sphere which serves as a source with known spectral radiance. Spectral Calibration consists of a laser and pen lamp illumination of integrating sphere. Environmental Testing includes temperature stability tests performed in environmental chamber.

Modular electronics packaging system

NASA Technical Reports Server (NTRS)

Hunter, Don J. (Inventor)

2001-01-01

A modular electronics packaging system includes multiple packaging slices that are mounted horizontally to a base structure. The slices interlock to provide added structural support. Each packaging slice includes a rigid and thermally conductive housing having four side walls that together form a cavity to house an electronic circuit. The chamber is enclosed on one end by an end wall, or web, that isolates the electronic circuit from a circuit in an adjacent packaging slice. The web also provides a thermal path between the electronic circuit and the base structure. Each slice also includes a mounting bracket that connects the packaging slice to the base structure. Four guide pins protrude from the slice into four corresponding receptacles in an adjacent slice. A locking element, such as a set screw, protrudes into each receptacle and interlocks with the corresponding guide pin. A conduit is formed in the slice to allow electrical connection to the electronic circuit.

Optimization and Control of Burning Plasmas Through High Performance Computing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pankin, Alexei

This project has revived the FACETS code, that has been developed under SciDAC fund- ing in 2008-2012. The code has been dormant for a number of years after the SciDAC funding stopped. FACETS depends on external packages. The external packages and libraries such as PETSc, FFTW, HDF5 and NETCDF that are included in FACETS have evolved during these years. Some packages in FACETS are also parts of other codes such as PlasmaState, NUBEAM, GACODES, and UEDGE. These packages have been also evolved together with their host codes which include TRANSP, TGYRO and XPTOR. Finally, there is also a set ofmore » packages in FACETS that are being developed and maintained by Tech-X. These packages include BILDER, SciMake, and FcioWrappers. Many of these packages evolved significantly during the last several years and FACETS had to be updated to synchronize with the re- cent progress in the external packages. The PI has introduced new changes to the BILDER package to support the updated interfaces to the external modules. During the last year of the project, the FACETS version of the UEDGE code has been extracted from FACETS as a standalone package. The PI collaborates with the scientists from LLNL on the updated UEDGE model in FACETS. Drs. T. Rognlien, M. Umansky and A. Dimits from LLNL are contributing to this task.« less

49 CFR 373.105 - Low value packages.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 5 2010-10-01 2010-10-01 false Low value packages. 373.105 Section 373.105... Carrier Receipts and Bills § 373.105 Low value packages. The carrier and shipper may elect to waive the... “low value” packages. This includes the option of shipping such packages under the provisions of 49 U.S...

Child-resistant and tamper-resistant packaging: A systematic review to inform tobacco packaging regulation.

PubMed

Jo, Catherine L; Ambs, Anita; Dresler, Carolyn M; Backinger, Cathy L

2017-02-01

We aimed to investigate the effects of special packaging (child-resistant, adult-friendly) and tamper-resistant packaging on health and behavioral outcomes in order to identify research gaps and implications for packaging standards for tobacco products. We searched seven databases for keywords related to special and tamper-resistant packaging, consulted experts, and reviewed citations of potentially relevant studies. 733 unique papers were identified. Two coders independently screened each title and abstract for eligibility. They then reviewed the full text of the remaining papers for a second round of eligibility screening. Included studies investigated a causal relationship between type of packaging or packaging regulation and behavioral or health outcomes and had a study population composed of consumers. Studies were excluded on the basis of publication type, if they were not peer-reviewed, and if they had low external validity. Two reviewers independently coded each paper for study and methodological characteristics and limitations. Discrepancies were discussed and resolved. The review included eight studies: four assessing people's ability to access the contents of different packaging types and four evaluating the impact of packaging requirements on health-related outcomes. Child-resistant packaging was generally more difficult to open than non-child-resistant packaging. Child-resistant packaging requirements have been associated with reductions in child mortality. Child-resistant packaging holds the expectation to reduce tobacco product poisonings among children under six. Published by Elsevier Inc.

Child-resistant and tamper-resistant packaging: A systematic review to inform tobacco packaging regulation

PubMed Central

Jo, Catherine L.; Ambs, Anita; Dresler, Carolyn M.; Backinger, Cathy L.

2017-01-01

Objective We aimed to investigate the effects of special packaging (child-resistant, adult-friendly) and tamper-resistant packaging on health and behavioral outcomes in order to identify research gaps and implications for packaging standards for tobacco products. Methods We searched seven databases for keywords related to special and tamper-resistant packaging, consulted experts, and reviewed citations of potentially relevant studies. 733 unique papers were identified. Two coders independently screened each title and abstract for eligibility. They then reviewed the full text of the remaining papers for a second round of eligibility screening. Included studies investigated a causal relationship between type of packaging or packaging regulation and behavioral or health outcomes and had a study population composed of consumers. Studies were excluded on the basis of publication type, if they were not peer-reviewed, and if they had low external validity. Two reviewers independently coded each paper for study and methodological characteristics and limitations. Discrepancies were discussed and resolved. Results The review included eight studies: four assessing people’s ability to access the contents of different packaging types and four evaluating the impact of packaging requirements on health-related outcomes. Child-resistant packaging was generally more difficult to open than non-child-resistant packaging. Child-resistant packaging requirements have been associated with reductions in child mortality. Conclusions Child-resistant packaging holds the expectation to reduce tobacco product poisonings among children under six. PMID:27939602

High-performance packaging for monolithic microwave and millimeter-wave integrated circuits

NASA Technical Reports Server (NTRS)

Shalkhauser, K. A.; Li, K.; Shih, Y. C.

1992-01-01

Packaging schemes were developed that provide low-loss, hermetic enclosure for advanced monolithic microwave and millimeter-wave integrated circuits (MMICs). The package designs are based on a fused quartz substrate material that offers improved radio frequency (RF) performance through 44 gigahertz (GHz). The small size and weight of the packages make them appropriate for a variety of applications, including phased array antenna systems. Packages were designed in two forms; one for housing a single MMIC chip, the second in the form of a multi-chip phased array module. The single chip array module was developed in three separate sizes, for chips of different geometry and frequency requirements. The phased array module was developed to address packaging directly for antenna applications, and includes transmission line and interconnect structures to support multi-element operation. All packages are fabricated using fused quartz substrate materials. As part of the packaging effort, a test fixture was developed to interface the single chip packages to conventional laboratory instrumentation for characterization of the packaged devices. The package and test fixture designs were both developed in a generic sense, optimizing performance for a wide range of possible applications and devices.

Self-renewal and multilineage differentiation of mouse dental epithelial stem cells.

PubMed

Chang, Julia Yu Fong; Wang, Cong; Jin, Chengliu; Yang, Chaofeng; Huang, Yanqing; Liu, Junchen; McKeehan, Wallace L; D'Souza, Rena N; Wang, Fen

2013-11-01

Understanding the cellular and molecular mechanisms underlying the self-renewal and differentiation of dental epithelial stem cells (DESCs) that support the unlimited growth potential of mouse incisors is critical for developing novel tooth regenerative therapies and unraveling the pathogenesis of odontogenic tumors. However, analysis of DESC properties and regulation has been limited by the lack of an in vitro assay system and well-documented DESC markers. Here, we describe an in vitro sphere culture system to isolate the DESCs from postnatal mouse incisor cervical loops (CLs) where the DESCs are thought to reside. The dissociated cells from CLs were able to expand and form spheres for multiple generations in the culture system. Lineage tracing indicated that DESC within the spheres were epithelial in origin as evident by lineage tracing. Upon stimulation, the sphere cells differentiated into cytokeratin 14- and amelogenin-expressing and mineral material-producing cells. Compared to the CL tissue, sphere cells expressed high levels of expression of Sca-1, CD49f (also designated as integrin α6), and CD44. Fluorescence-activated cell sorting (FACS) analyses of mouse incisor CL cells further showed that the CD49f(Bright) population was enriched in sphere-forming cells. In addition, the CD49f(Bright) population includes both slow-cycling and Lgr5(+) DESCs. The in vitro sphere culture system and identification of CD49f(Bright) as a DESC marker provide a novel platform for enriching DESCs, interrogating how maintenance, cell fate determination, and differentiation of DESCs are regulated, and developing tooth regenerative therapies. © 2013.

Self-renewal and Multilineage Differentiation of Mouse Dental Epithelial Stem Cells

PubMed Central

Chang, Julia Yu Fong; Wang, Cong; Jin, Chengliu; Yang, Chaofeng; Huang, Yanqing; Liu, Junchen; McKeehan, Wallace L.; D’Souza, Rena N.; Wang, Fen

2013-01-01

Understanding the cellular and molecular mechanisms underlying the self-renewal and differentiation of dental epithelial stem cells (DESCs) that support the unlimited growth potential of mouse incisors is critical for developing novel tooth regenerative therapies and unraveling the pathogenesis of odontogenic tumors. However, analysis of DESC properties and regulation has been limited by the lack of an in vitro assay system and well-documented DESC markers. Here, we describe an in vitro sphere culture system to isolate the DESCs from postnatal mouse incisor cervical loops (CLs) where the DESCs are thought to reside. The dissociated cells from CLs were able to expand and form spheres for multiple generations in the culture system. Lineage tracing indicated that DESC within the spheres were epithelial in origin as evident by lineage tracing. Upon stimulation, the sphere cells differentiated into cytokeratin 14- and amelogenin-expressing and mineral material-producing cells. Compared to the CL tissue, sphere cells expressed high levels of expression of Sca-1, CD49f (also designated as integrin α6), and CD44. Fluorescence-activated cell sorting (FACS) analyses of mouse incisor CL cells further showed that the CD49fBright population was enriched in sphere-forming cells. In addition, the CD49fBright population includes both slow-cycling and Lgr5+ DESCs. The in vitro sphere culture system and identification of CD49fBright as a DESC marker provide a novel plateform for enriching DESCs, interrogating how maintenance, cell fate determination, and differentiation of DESCs are regulated, and developing tooth regenerative therapies. PMID:23906788

Dispersed-nanoparticle loading synthesis for monodisperse Au-titania composite particles and their crystallization for highly active UV and visible photocatalysts.

PubMed

Sakamoto, Takeshi; Nagao, Daisuke; Noba, Masahiro; Ishii, Haruyuki; Konno, Mikio

2014-06-24

Submicrometer-sized amorphous titania spheres incorporating Au nanoparticles (NPs) were prepared in a one-pot synthesis consisting of a sol-gel reaction of titanium(IV) isopropoxide in the presence of chloroauric acid and a successive reduction with sodium borohydride in a mixed solvent of ethanol/acetonitrile. The synthesis was allowed to prepare monodisperse titania spheres that homogeneously incorporated Au NPs with sizes of ca. 7 nm. The Au NP-loaded titania spheres underwent different crystallization processes, including 500 °C calcination in air, high-temperature hydrothermal treatment (HHT), and/or low-temperature hydrothermal treatment (LHT). Photocatalytic experiments were conducted with the Au NP-loaded crystalline titania spheres under irradiation of UV and visible light. A combined process of LHT at 80 °C followed by calcination at 500 °C could effectively crystallize titania spheres maintaining the dispersion state of Au NPs, which led to photocatalytic activity higher than that of commercial P25 under UV irradiation. Under visible light irradiation, the Au NP-titania spheres prepared with a crystallization process of LHT at 80 °C for 6 h showed photocatalytic activity much higher than a commercial product of visible light photocatalyst. Structure analysis of the visible light photocatalysts indicates the importance of prevention of the Au NPs aggregation in the crystallization processes for enhancement of photocatalytic activity.

48 CFR 211.272 - Alternate preservation, packaging, and packing.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., packaging, and packing. 211.272 Section 211.272 Federal Acquisition Regulations System DEFENSE ACQUISITION... Requirements Documents 211.272 Alternate preservation, packaging, and packing. Use the provision at 252.211-7004, Alternate Preservation, Packaging, and Packing, in solicitations which include military...

Some constructions of biharmonic maps and Chen’s conjecture on biharmonic hypersurfaces

NASA Astrophysics Data System (ADS)

Ou, Ye-Lin

2012-04-01

We give several construction methods and use them to produce many examples of proper biharmonic maps including biharmonic tori of any dimension in Euclidean spheres (Theorem 2.2, Corollaries 2.3, 2.4 and 2.6), biharmonic maps between spheres (Theorem 2.9) and into spheres (Theorem 2.10) via orthogonal multiplications and eigenmaps. We also study biharmonic graphs of maps, derive the equation for a function whose graph is a biharmonic hypersurface in a Euclidean space, and give an equivalent formulation of Chen's conjecture on biharmonic hypersurfaces by using the biharmonic graph equation (Theorem 4.1) which paves a way for the analytic study of the conjecture.

Colloidal alloys with preassembled clusters and spheres.

PubMed

Ducrot, Étienne; He, Mingxin; Yi, Gi-Ra; Pine, David J

2017-06-01

Self-assembly is a powerful approach for constructing colloidal crystals, where spheres, rods or faceted particles can build up a myriad of structures. Nevertheless, many complex or low-coordination architectures, such as diamond, pyrochlore and other sought-after lattices, have eluded self-assembly. Here we introduce a new design principle based on preassembled components of the desired superstructure and programmed nearest-neighbour DNA-mediated interactions, which allows the formation of otherwise unattainable structures. We demonstrate the approach using preassembled colloidal tetrahedra and spheres, obtaining a class of colloidal superstructures, including cubic and tetragonal colloidal crystals, with no known atomic analogues, as well as percolating low-coordination diamond and pyrochlore sublattices never assembled before.

Characterization of Lubricants on Ball Bearings by FT-IR Using an Integrating Sphere

NASA Technical Reports Server (NTRS)

Street, K. W.; Pepper, S. V.; Wright, A. A.; Grady, B.

2007-01-01

Fourier Transform-Infrared reflectance microspectroscopy has been used extensively for the examination of coatings on nonplanar surfaces such as ball bearings. While this technique offers considerable advantages, practical application has many drawbacks, some of which are easily overcome by the use of integrating sphere technology. This paper describes the use of an integrating sphere for the quantification of thin layers of lubricant on the surface of ball bearings and the parameters which require optimization in order to obtain reliable data. Several applications of the technique are discussed including determination of lubricant load on 12.7 mm steel ball bearings and the examination of degraded lubricant on post mortem specimens.

Broadband radiometer

DOEpatents

Cannon, Theodore W.

1994-01-01

A broadband radiometer including (a) an optical integrating sphere having a enerally spherical integrating chamber and an entry port for receiving light (e.g., having visible and ultraviolet fractions), (b) a first optical radiation detector for receiving light from the sphere and producing an electrical output signal corresponding to broadband radiation, (c) a second optical radiation detector for receiving light from the sphere and producing an electrical output signal corresponding to a predetermined wavelength fraction of the broadband radiation, and (d) an output for producing an electrical signal which is proportional to the difference between the two electrical output signals. The radiometer is very useful, for example, in measuring the absolute amount of ultraviolet light present in a given light sample.

Broadband radiometer

DOEpatents

Cannon, T.W.

1994-07-26

A broadband radiometer is disclosed including (a) an optical integrating sphere having generally spherical integrating chamber and an entry port for receiving light (e.g., having visible and ultraviolet fractions), (b) a first optical radiation detector for receiving light from the sphere and producing an electrical output signal corresponding to broadband radiation, (c) a second optical radiation detector for receiving light from the sphere and producing an electrical output signal corresponding to a predetermined wavelength fraction of the broadband radiation, and (d) an output for producing an electrical signal which is proportional to the difference between the two electrical output signals. The radiometer is very useful, for example, in measuring the absolute amount of ultraviolet light present in a given light sample. 8 figs.

Monostatic lidar/radar invisibility using coated spheres.

PubMed

Zhai, Peng-Wang; You, Yu; Kattawar, George W; Yang, Ping

2008-02-04

The Lorenz-Mie theory is revisited to explicitly include materials whose permeability is different from unity. The expansion coefficients of the scattered field are given for light scattering by both homogeneous and coated spheres. It is shown that the backscatter is exactly zero if the impedance of the spherical particles is equal to the intrinsic impedance of the surrounding medium. If spherical particles are sufficiently large, the zero backscatter can be explained as impedance matching using the asymptotic expression for the radar backscattering cross section. In the case of a coated sphere, the shell can be regarded as a cloak if the product of the thickness and the imaginary part of the refractive index of the outer shell is large.

Space station power semiconductor package

NASA Technical Reports Server (NTRS)

Balodis, Vilnis; Berman, Albert; Devance, Darrell; Ludlow, Gerry; Wagner, Lee

1987-01-01

A package of high-power switching semiconductors for the space station have been designed and fabricated. The package includes a high-voltage (600 volts) high current (50 amps) NPN Fast Switching Power Transistor and a high-voltage (1200 volts), high-current (50 amps) Fast Recovery Diode. The package features an isolated collector for the transistors and an isolated anode for the diode. Beryllia is used as the isolation material resulting in a thermal resistance for both devices of .2 degrees per watt. Additional features include a hermetical seal for long life -- greater than 10 years in a space environment. Also, the package design resulted in a low electrical energy loss with the reduction of eddy currents, stray inductances, circuit inductance, and capacitance. The required package design and device parameters have been achieved. Test results for the transistor and diode utilizing the space station package is given.

Pre-release plastic packaging of MEMS and IMEMS devices

DOEpatents

Peterson, Kenneth A.; Conley, William R.

2002-01-01

A method is disclosed for pre-release plastic packaging of MEMS and IMEMS devices. The method can include encapsulating the MEMS device in a transfer molded plastic package. Next, a perforation can be made in the package to provide access to the MEMS elements. The non-ablative material removal process can include wet etching, dry etching, mechanical machining, water jet cutting, and ultrasonic machining, or any combination thereof. Finally, the MEMS elements can be released by using either a wet etching or dry plasma etching process. The MEMS elements can be protected with a parylene protective coating. After releasing the MEMS elements, an anti-stiction coating can be applied. The perforating step can be applied to both sides of the device or package. A cover lid can be attached to the face of the package after releasing any MEMS elements. The cover lid can include a window for providing optical access. The method can be applied to any plastic packaged microelectronic device that requires access to the environment, including chemical, pressure, or temperature-sensitive microsensors; CCD chips, photocells, laser diodes, VCSEL's, and UV-EPROMS. The present method places the high-risk packaging steps ahead of the release of the fragile portions of the device. It also provides protection for the die in shipment between the molding house and the house that will release the MEMS elements and subsequently treat the surfaces.

Effective conductivity of suspensions of overlapping spheres

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, I.C.; Torquato, S.

1992-03-15

An accurate first-passage simulation technique formulated by the authors (J. Appl. Phys. {bold 68}, 3892 (1990)) is employed to compute the effective conductivity {sigma}{sub {ital e}} of distributions of penetrable (or overlapping) spheres of conductivity {sigma}{sub 2} in a matrix of conductivity {sigma}{sub 1}. Clustering of particles in this model results in a generally intricate topology for virtually the entire range of sphere volume fractions {phi}{sub 2} (i.e., 0{le}{phi}{sub 2}{le}1). Results for the effective conductivity {sigma}{sub {ital e}} are presented for several values of the conductivity ratio {alpha}={sigma}{sub 2}/{sigma}{sub 1}, including superconducting spheres ({alpha}={infinity}) and perfectly insulating spheres ({alpha}=0), andmore » for a wide range of volume fractions. The data are shown to lie between rigorous three-point bounds on {sigma}{sub {ital e}} for the same model. Consistent with the general observations of Torquato (J. Appl. Phys. {bold 58}, 3790 (1985)) regarding the utility of rigorous bounds, one of the bounds provides a good estimate of the effective conductivity, even in the extreme contrast cases ({alpha}{much gt}1 or {alpha}{congruent}0), depending upon whether the system is below or above the percolation threshold.« less

Spectral correction factors for conventional neutron dosemeters used in high-energy neutron environments.

PubMed

Lee, K W; Sheu, R J

2015-04-01

High-energy neutrons (>10 MeV) contribute substantially to the dose fraction but result in only a small or negligible response in most conventional moderated-type neutron detectors. Neutron dosemeters used for radiation protection purpose are commonly calibrated with (252)Cf neutron sources and are used in various workplace. A workplace-specific correction factor is suggested. In this study, the effect of the neutron spectrum on the accuracy of dose measurements was investigated. A set of neutron spectra representing various neutron environments was selected to study the dose responses of a series of Bonner spheres, including standard and extended-range spheres. By comparing (252)Cf-calibrated dose responses with reference values based on fluence-to-dose conversion coefficients, this paper presents recommendations for neutron field characterisation and appropriate correction factors for responses of conventional neutron dosemeters used in environments with high-energy neutrons. The correction depends on the estimated percentage of high-energy neutrons in the spectrum or the ratio between the measured responses of two Bonner spheres (the 4P6_8 extended-range sphere versus the 6″ standard sphere). © The Author 2014. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

A novel upwind stabilized discontinuous finite element angular framework for deterministic dose calculations in magnetic fields.

PubMed

Yang, R; Zelyak, O; Fallone, B G; St-Aubin, J

2018-01-30

Angular discretization impacts nearly every aspect of a deterministic solution to the linear Boltzmann transport equation, especially in the presence of magnetic fields, as modeled by a streaming operator in angle. In this work a novel stabilization treatment of the magnetic field term is developed for an angular finite element discretization on the unit sphere, specifically involving piecewise partitioning of path integrals along curved element edges into uninterrupted segments of incoming and outgoing flux, with outgoing components updated iteratively. Correct order-of-accuracy for this angular framework is verified using the method of manufactured solutions for linear, quadratic, and cubic basis functions in angle. Higher order basis functions were found to reduce the error especially in strong magnetic fields and low density media. We combine an angular finite element mesh respecting octant boundaries on the unit sphere to spatial Cartesian voxel elements to guarantee an unambiguous transport sweep ordering in space. Accuracy for a dosimetrically challenging scenario involving bone and air in the presence of a 1.5 T parallel magnetic field is validated against the Monte Carlo package GEANT4. Accuracy and relative computational efficiency were investigated for various angular discretization parameters. 32 angular elements with quadratic basis functions yielded a reasonable compromise, with gamma passing rates of 99.96% (96.22%) for a 2%/2 mm (1%/1 mm) criterion. A rotational transformation of the spatial calculation geometry is performed to orient an arbitrary magnetic field vector to be along the z-axis, a requirement for a constant azimuthal angular sweep ordering. Working on the unit sphere, we apply the same rotational transformation to the angular domain to align its octants with the rotated Cartesian mesh. Simulating an oblique 1.5 T magnetic field against GEANT4 yielded gamma passing rates of 99.42% (95.45%) for a 2%/2 mm (1%/1 mm) criterion.

A novel upwind stabilized discontinuous finite element angular framework for deterministic dose calculations in magnetic fields

NASA Astrophysics Data System (ADS)

Yang, R.; Zelyak, O.; Fallone, B. G.; St-Aubin, J.

2018-02-01

Angular discretization impacts nearly every aspect of a deterministic solution to the linear Boltzmann transport equation, especially in the presence of magnetic fields, as modeled by a streaming operator in angle. In this work a novel stabilization treatment of the magnetic field term is developed for an angular finite element discretization on the unit sphere, specifically involving piecewise partitioning of path integrals along curved element edges into uninterrupted segments of incoming and outgoing flux, with outgoing components updated iteratively. Correct order-of-accuracy for this angular framework is verified using the method of manufactured solutions for linear, quadratic, and cubic basis functions in angle. Higher order basis functions were found to reduce the error especially in strong magnetic fields and low density media. We combine an angular finite element mesh respecting octant boundaries on the unit sphere to spatial Cartesian voxel elements to guarantee an unambiguous transport sweep ordering in space. Accuracy for a dosimetrically challenging scenario involving bone and air in the presence of a 1.5 T parallel magnetic field is validated against the Monte Carlo package GEANT4. Accuracy and relative computational efficiency were investigated for various angular discretization parameters. 32 angular elements with quadratic basis functions yielded a reasonable compromise, with gamma passing rates of 99.96% (96.22%) for a 2%/2 mm (1%/1 mm) criterion. A rotational transformation of the spatial calculation geometry is performed to orient an arbitrary magnetic field vector to be along the z-axis, a requirement for a constant azimuthal angular sweep ordering. Working on the unit sphere, we apply the same rotational transformation to the angular domain to align its octants with the rotated Cartesian mesh. Simulating an oblique 1.5 T magnetic field against GEANT4 yielded gamma passing rates of 99.42% (95.45%) for a 2%/2 mm (1%/1 mm) criterion.

Package Up Your Troubles--An Introduction to Package Libraries

ERIC Educational Resources Information Center

Frank, Colin

1978-01-01

Discusses a "package deal" library--a prefabricated building including interior furnishing--in terms of costs, fitness for purpose, and interior design, i.e., shelving, flooring, heating, lighting, and humidity. Advantages and disadvantages of the package library are also considered. (Author/MBR)

Packaging & Other Structures. Stuff That Works! A Technology Curriculum for the Elementary Grades.

ERIC Educational Resources Information Center

Benenson, Gary

This book explores all kinds of packaging materials including bags, boxes, etc. and how they are used to protect and display products. Contents are divided into six chapters: (1) "Appetizers" includes activities that can be done individually to become familiar with the topic of packaging and structures; (2) "Concepts" provides…

DOE Office of Scientific and Technical Information (OSTI.GOV)

Radiom, Milad, E-mail: milad.radiom@unige.ch; Ducker, William, E-mail: wducker@vt.edu; Robbins, Brian

The hydrodynamic interaction of two closely spaced micron-scale spheres undergoing Brownian motion was measured as a function of their separation. Each sphere was attached to the distal end of a different atomic force microscopy cantilever, placing each sphere in a stiff one-dimensional potential (0.08 Nm{sup −1}) with a high frequency of thermal oscillations (resonance at 4 kHz). As a result, the sphere’s inertial and restoring forces were significant when compared to the force due to viscous drag. We explored interparticle gap regions where there was overlap between the two Stokes layers surrounding each sphere. Our experimental measurements are the firstmore » of their kind in this parameter regime. The high frequency of oscillation of the spheres means that an analysis of the fluid dynamics would include the effects of fluid inertia, as described by the unsteady Stokes equation. However, we find that, for interparticle separations less than twice the thickness of the wake of the unsteady viscous boundary layer (the Stokes layer), the hydrodynamic interaction between the Brownian particles is well-approximated by analytical expressions that neglect the inertia of the fluid. This is because elevated frictional forces at narrow gaps dominate fluid inertial effects. The significance is that interparticle collisions and concentrated suspensions at this condition can be modeled without the need to incorporate fluid inertia. We suggest a way to predict when fluid inertial effects can be ignored by including the gap-width dependence into the frequency number. We also show that low frequency number analysis can be used to determine the microrheology of mixtures at interfaces.« less

Food-packaging interactions influencing quality and safety.

PubMed

Hotchkiss, J H

1997-01-01

Interactions between foods and packaging can be detrimental to quality and/or safety. Changes in product flavour due to aroma sorption and the transfer of undesirable flavours from packaging to foods are important mechanisms of deterioration when foods are packaged in polymer-based materials. Careful consideration must be given to those factors affecting such interactions when selecting packaging materials in order to maximize product quality, safety, and shelf-life while minimizing undesirable changes. Product considerations include sensitivity to flavour and related deteriorations, colour changes, vitamin loss, microbial activity, and amount of flavour available. Storage considerations include temperature, time, and processing method. Polymer considerations include type of polymer and processing method, volume or mass of polymer to product ratio, and whether the interaction is Fickian or non-Fickian. Methodology to determine the extent of such interactions must be developed. Direct interactions between food and packaging are not necessarily detrimental. The same principles governing undesirable interactions can be used to affect desirable outcomes. Examples include films which directly intercept or absorb oxygen, inhibit microorganisms, remove undesirable flavours by sorption, or indicate safety and product shelf-life.

World Presidents Organization

NASA Technical Reports Server (NTRS)

2010-01-01

Members of the World Presidents' Organization enjoy exhibits at StenniSphere, the visitor center and museum at NASA's John C. Stennis Space Center during a Jan. 26 visit to the site. WPO members from several states spent the day touring Stennis facilities and learning about the work of the nation's premier rocket engine testing site. Exhibits enjoyed included a mockup of the International Space Station and the interactive Science on a Sphere globe.

Rotation of large asymmetrical absorbing objects by Laguerre-Gauss beams.

PubMed

Herne, Catherine M; Capuzzi, Kristina M; Sobel, Emily; Kropas, Ryan T

2015-09-01

In this Letter, we show the manipulation and rotation of opaque graphite through adhesion with optically trapped polystyrene spheres. The absorbing graphite is rotated by the orbital angular momentum transfer from a Laguerre-Gauss laser mode and is trapped due to the presence of refracting spheres. This technique is effective for trapping and rotating absorbing objects of all sizes, including those larger than the laser mode.

Feasibility study of low angle planetary entry. [probe design for Jovian entry

NASA Technical Reports Server (NTRS)

Defrees, R. E.

1975-01-01

The feasibility of a Jovian entry by a probe originally designed for Saturn and Uranus entries is examined. An entry probe is described which is capable of release near an outer planet's sphere of influence and descent to a predetermined target entry point in the planet's atmosphere. The probe is designed so as to survive the trapped particle radiation belts and an entry heating pulse. Data is gathered and relayed to an overflying spacecraft bus during descent. Probe variations for two similar missions are described. In the first flyby of Jupiter by a Pioneer spacecraft launched during the 1979 opportunity is examined parametrically. In the second mission an orbiter based on Pioneer and launched in 1980 is defined in specific terms. The differences rest in the science payloads and directly affected wiring and electronics packages.

ReaDDy - A Software for Particle-Based Reaction-Diffusion Dynamics in Crowded Cellular Environments

PubMed Central

Schöneberg, Johannes; Noé, Frank

2013-01-01

We introduce the software package ReaDDy for simulation of detailed spatiotemporal mechanisms of dynamical processes in the cell, based on reaction-diffusion dynamics with particle resolution. In contrast to other particle-based reaction kinetics programs, ReaDDy supports particle interaction potentials. This permits effects such as space exclusion, molecular crowding and aggregation to be modeled. The biomolecules simulated can be represented as a sphere, or as a more complex geometry such as a domain structure or polymer chain. ReaDDy bridges the gap between small-scale but highly detailed molecular dynamics or Brownian dynamics simulations and large-scale but little-detailed reaction kinetics simulations. ReaDDy has a modular design that enables the exchange of the computing core by efficient platform-specific implementations or dynamical models that are different from Brownian dynamics. PMID:24040218

ELAS: A powerful, general purpose image processing package

NASA Technical Reports Server (NTRS)

Walters, David; Rickman, Douglas

1991-01-01

ELAS is a software package which has been utilized as an image processing tool for more than a decade. It has been the source of several commercial packages. Now available on UNIX workstations it is a very powerful, flexible set of software. Applications at Stennis Space Center have included a very wide range of areas including medicine, forestry, geology, ecological modeling, and sonar imagery. It remains one of the most powerful image processing packages available, either commercially or in the public domain.

49 CFR 178.955 - General requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... void space(s) and to prevent significant movement of the inner packagings. (h) Proof of compliance. In... subchapter. Variations are permitted in inner packagings of a tested Large Packaging, without further testing... determine that the inner packaging, including closure, maintains an equivalent level of performance is...

49 CFR 178.955 - General requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... void space(s) and to prevent significant movement of the inner packagings. (h) Proof of compliance. In... subchapter. Variations are permitted in inner packagings of a tested Large Packaging, without further testing... determine that the inner packaging, including closure, maintains an equivalent level of performance is...

49 CFR 178.955 - General requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... void space(s) and to prevent significant movement of the inner packagings. (h) Proof of compliance. In... subchapter. Variations are permitted in inner packagings of a tested Large Packaging, without further testing... determine that the inner packaging, including closure, maintains an equivalent level of performance is...

49 CFR 178.955 - General requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... void space(s) and to prevent significant movement of the inner packagings. (h) Proof of compliance. In... subchapter. Variations are permitted in inner packagings of a tested Large Packaging, without further testing... determine that the inner packaging, including closure, maintains an equivalent level of performance is...

Optimal segmentation and packaging process

DOEpatents

Kostelnik, K.M.; Meservey, R.H.; Landon, M.D.

1999-08-10

A process for improving packaging efficiency uses three dimensional, computer simulated models with various optimization algorithms to determine the optimal segmentation process and packaging configurations based on constraints including container limitations. The present invention is applied to a process for decontaminating, decommissioning (D and D), and remediating a nuclear facility involving the segmentation and packaging of contaminated items in waste containers in order to minimize the number of cuts, maximize packaging density, and reduce worker radiation exposure. A three-dimensional, computer simulated, facility model of the contaminated items are created. The contaminated items are differentiated. The optimal location, orientation and sequence of the segmentation and packaging of the contaminated items is determined using the simulated model, the algorithms, and various constraints including container limitations. The cut locations and orientations are transposed to the simulated model. The contaminated items are actually segmented and packaged. The segmentation and packaging may be simulated beforehand. In addition, the contaminated items may be cataloged and recorded. 3 figs.

Flavoured cigarettes, sensation seeking and adolescents' perceptions of cigarette brands.

PubMed

Manning, K C; Kelly, K J; Comello, M L

2009-12-01

This study examined the interactive effects of cigarette package flavour descriptors and sensation seeking on adolescents' brand perceptions. High school students (n = 253) were randomly assigned to one of two experimental conditions and sequentially exposed to cigarette package illustrations for three different brands. In the flavour descriptor condition, the packages included a description of the cigarettes as "cherry", while in the traditional descriptor condition the cigarette brands were described with common phrases found on tobacco packages such as "domestic blend." Following exposure to each package participants' hedonic beliefs, brand attitudes and trial intentions were assessed. Sensation seeking was also measured, and participants were categorised as lower or higher sensation seekers. Across hedonic belief, brand attitude and trial intention measures, there were interactions between package descriptor condition and sensation seeking. These interactions revealed that among high (but not low) sensation seekers, exposure to cigarette packages including sweet flavour descriptors led to more favourable brand impressions than did exposure to packages with traditional descriptors. Among high sensation seeking youths, the appeal of cigarette brands is enhanced through the use of flavours and associated descriptions on product packaging.

User’s guide for MapMark4—An R package for the probability calculations in three-part mineral resource assessments

USGS Publications Warehouse

Ellefsen, Karl J.

2017-06-27

MapMark4 is a software package that implements the probability calculations in three-part mineral resource assessments. Functions within the software package are written in the R statistical programming language. These functions, their documentation, and a copy of this user’s guide are bundled together in R’s unit of shareable code, which is called a “package.” This user’s guide includes step-by-step instructions showing how the functions are used to carry out the probability calculations. The calculations are demonstrated using test data, which are included in the package.

Spectral Radiance of a Large-Area Integrating Sphere Source

PubMed Central

Walker, James H.; Thompson, Ambler

1995-01-01

The radiance and irradiance calibration of large field-of-view scanning and imaging radiometers for remote sensing and surveillance applications has resulted in the development of novel calibration techniques. One of these techniques is the employment of large-area integrating sphere sources as radiance or irradiance secondary standards. To assist the National Aeronautical and Space Administration’s space based ozone measurement program, a commercially available large-area internally illuminated integrating sphere source’s spectral radiance was characterized in the wavelength region from 230 nm to 400 nm at the National Institute of Standards and Technology. Spectral radiance determinations and spatial mappings of the source indicate that carefully designed large-area integrating sphere sources can be measured with a 1 % to 2 % expanded uncertainty (two standard deviation estimate) in the near ultraviolet with spatial nonuniformities of 0.6 % or smaller across a 20 cm diameter exit aperture. A method is proposed for the calculation of the final radiance uncertainties of the source which includes the field of view of the instrument being calibrated. PMID:29151725

Wetting, meniscus structure, and capillary interactions of microspheres bound to a cylindrical liquid interface.

PubMed

Kim, Paul Y; Dinsmore, Anthony D; Hoagland, David A; Russell, Thomas P

2018-03-14

Wetting, meniscus structure, and capillary interactions for polystyrene microspheres deposited on constant curvature cylindrical liquid interfaces, constructed from nonvolatile ionic or oligomeric liquids, were studied by optical interferometry and optical microscopy. The liquid interface curvature resulted from the preferential wetting of finite width lines patterned onto planar silicon substrates. Key variables included sphere diameter, nominal (or average) contact angle, and deviatoric interfacial curvature. Menisci adopted the quadrupolar symmetry anticipated by theory, with interfacial deformation closely following predicted dependences on sphere diameter and nominal contact angle. Unexpectedly, the contact angle was not constant locally around the contact line, the nominal contact angle varied among seemingly identical spheres, and the maximum interface deviation did not follow the predicted dependence on deviatoric interfacial curvature. Instead, this deviation was up to an order-of-magnitude larger than predicted. Trajectories of neighboring microspheres visually manifested quadrupole-quadrupole interactions, eventually producing square sphere packings that foreshadow interfacial assembly as a potential route to hierarchical 2D particle structures.

Mental and social health in disasters: the Sphere standards and post-tsunami psychosocial interventions in Asia.

PubMed

Henderson, Silja E K; Elsass, Peter; Berliner, Peter

2016-07-01

The primary objective of this paper is to examine and inform the mental health and psychosocial support standards of the 2011 edition of the Sphere Project's Humanitarian Charter and Minimum Standards in Humanitarian Response. This is done through a qualitative analysis of internal evaluation documents, reflecting four long-term humanitarian psychosocial programmes in different countries in post-tsunami Asia. The analysis yielded three overall conclusions. First, the Sphere standards on mental health and psychosocial support generally are highly relevant to long-term psychosocial interventions after disasters such as the Indian Ocean tsunami of 26 December 2004, and their application in such settings may improve the quality of the response. Second, some of the standards in the current Sphere handbook may lack sufficient guidance to ensure the quality of humanitarian response required. Third, the long-term intervention approach poses specific challenges to programming, a problem that could be addressed by including additional guidance in the publication. © 2016 The Author(s). Disasters © Overseas Development Institute, 2016.

Method and apparatus for producing gas-filled hollow spheres. [target pellets for inertial confinement fusion

NASA Technical Reports Server (NTRS)

Wang, T. G.; Elleman, D. D. (Inventor)

1982-01-01

A system for forming hollow spheres containing pressured gas is described which includes a cylinder device containing a molten solid material with a nozzle at its end. A second gas nozzle, lying slightly upstream from the tip of the first nozzle, is connected to a source that applies pressured filler gas that is to fill the hollow spheres. High pressure is applied to the molten metal, as by moving a piston within the cylinder device, to force the molten material out of the first nozzle. At the same time, pressured gas fills the center of the extruded hollow liquid pipe that breaks into hollow spheres. The environment outside the nozzles contains gas at a high pressure such as 100 atmospheres. Gas is supplied to the gas nozzle at a slightly higher pressure such as 101 atmospheres. The pressure applied to the molten material is at a still higher pressure such as 110 atmospheres.

Designing non-Hermitian dynamics for conservative state evolution on the Bloch sphere

NASA Astrophysics Data System (ADS)

Yu, Sunkyu; Piao, Xianji; Park, Namkyoo

2018-03-01

An evolution on the Bloch sphere is the fundamental state transition, including optical polarization controls and qubit operations. Conventional evolution of a polarization state or qubit is implemented within a closed system that automatically satisfies energy conservation from the Hermitian formalism. Although particular forms of static non-Hermitian Hamiltonians, such as parity-time-symmetric Hamiltonians, allow conservative states in an open system, the criteria for the energy conservation in a dynamical open system have not been fully explored. Here, we derive the condition of conservative state evolution in open-system dynamics and its inverse design method, by developing the non-Hermitian modification of the Larmor precession equation. We show that the geometrically designed locus on the Bloch sphere can be realized by different forms of dynamics, leading to the isolocus family of non-Hermitian dynamics. This increased degree of freedom allows the complementary phenomena of error-robust and highly sensitive evolutions on the Bloch sphere, which could be applicable to stable polarizers, quantum gates, and optimized sensors in dynamical open systems.

29 CFR 99.320 - Report submission.

Code of Federal Regulations, 2014 CFR

2014-07-01

... completed and the data collection form and reporting package shall be submitted within the earlier of 30... the data elements prescribed by OMB. (c) Reporting package. The reporting package shall include the... data collection form described in paragraph (b) of this section and one copy of the reporting package...

29 CFR 99.320 - Report submission.

Code of Federal Regulations, 2010 CFR

2010-07-01

... completed and the data collection form and reporting package shall be submitted within the earlier of 30... the data elements prescribed by OMB. (c) Reporting package. The reporting package shall include the... data collection form described in paragraph (b) of this section and one copy of the reporting package...

High-performance packaging for monolithic microwave and millimeter-wave integrated circuits

NASA Technical Reports Server (NTRS)

Shalkhauser, K. A.; Li, K.; Shih, Y. C.

1992-01-01

Packaging schemes are developed that provide low-loss, hermetic enclosure for enhanced monolithic microwave and millimeter-wave integrated circuits. These package schemes are based on a fused quartz substrate material offering improved RF performance through 44 GHz. The small size and weight of the packages make them useful for a number of applications, including phased array antenna systems. As part of the packaging effort, a test fixture was developed to interface the single chip packages to conventional laboratory instrumentation for characterization of the packaged devices.

Function Package for Computing Quantum Resource Measures

NASA Astrophysics Data System (ADS)

Huang, Zhiming

2018-05-01

In this paper, we present a function package for to calculate quantum resource measures and dynamics of open systems. Our package includes common operators and operator lists, frequently-used functions for computing quantum entanglement, quantum correlation, quantum coherence, quantum Fisher information and dynamics in noisy environments. We briefly explain the functions of the package and illustrate how to use the package with several typical examples. We expect that this package is a useful tool for future research and education.

Combustion of a Polymer (PMMA) Sphere in Microgravity

NASA Technical Reports Server (NTRS)

Yang, Jiann C.; Hamins, Anthony; Donnelly, Michelle K.

1999-01-01

A series of low gravity, aircraft-based, experiments was conducted to investigate the combustion of supported thermoplastic polymer spheres under varying ambient conditions. The three types of thermoplastic investigated were polymethylmethacrylate (PMMA), polypropylene (PP). and polystyrene (PS). Spheres with diameters ranging from 2 mm to 6.35 mm were tested. The total initial pressure varied from 0.05 MPa to 0. 15 MPa whereas the ambient oxygen concentration varied from 19 % to 30 % (by volume). The ignition system consisted of a pair of retractable energized coils. Two CCD cameras recorded the burning histories of the spheres. The video sequences revealed a number of dynamic events including bubbling and sputtering, as well as soot shell formation and break-up during combustion of the spheres at reduced gravity. The ejection of combusting material from the burning spheres represents a fire hazard that must be considered at reduced gravity. The ejection process was found to be sensitive to polymer type. All average burning rates were measured to increase with initial sphere diameter and oxygen concentration, whereas the initial pressure had little effect. The three thermoplastic types exhibited different burning characteristics. For the same initial conditions, the burning rate of PP was slower than PMMA, whereas the burning rate of PS was comparable to PMMA. The transient diameter of the burning thermoplastic exhibited two distinct periods: an initial period (enduring approximately half of the total burn duration) when the diameter remained approximately constant, and a final period when the square of the diameter linearly decreased with time. A simple homogeneous two-phase model was developed to understand the changing diameter of the burning sphere. Its value is based on a competition between diameter reduction due to mass loss from burning and sputtering, and diameter expansion due to the processes of swelling (density decrease with heating) and bubble growth. The model relies on empirical parameters for input, such as the burning rate and the duration of the initial and final burning periods.

Dynamic compaction of human mesenchymal stem/precursor cells (MSC) into spheres self-activates caspase-dependent IL1 signaling to enhance secretion of modulators of inflammation and immunity (PGE2, TSG6 and STC1)

PubMed Central

Bazhanov, Nikolay; Kuhlman, Jessica; Prockop, Darwin J.

2013-01-01

Human mesenchymal stem/precursor cells (MSC) are similar to some other stem/progenitor cells in that they compact into spheres when cultured in hanging drops or on non-adherent surfaces. Assembly of MSC into spheres alters many of their properties, including enhanced secretion of factors that mediate inflammatory and immune responses. Here we demonstrated that MSC spontaneously aggregated into sphere-like structures after injection into a subcutaneous air pouch or the peritoneum of mice. The structures were similar to MSC spheres formed in cultures demonstrated by the increased expression of genes for inflammation-modulating factors TSG6, STC1, and COX2, a key enzyme in production of PGE2. To identify the signaling pathways involved, hanging drop cultures were used to follow the time-dependent changes in the cells as they compacted into spheres. Among the genes up-regulated were genes for the stress-activated signaling pathway for IL1α/β, and the contact-dependent signaling pathway for Notch. An inhibitor of caspases reduced the up-regulation of IL1A/B expression, and inhibitors of IL1 signaling decreased production of PGE2, TSG6 and STC1. Also, inhibition of IL1A/B expression and secretion of PGE2 negated the anti-inflammatory effects of MSC spheres on stimulated macrophages. Experiments with γ-secretase inhibitors suggested that Notch signaling was also required for production of PGE2 but not TSG6 or STC1. The results indicated that assembly of MSC into spheres triggers caspase-dependent IL1 signaling and the secretion of modulators of inflammation and immunity. Similar aggregation in vivo may account for some of the effects observed with administration of the cells in animal models. PMID:23922312

(Climate) Change in young people's minds - From categories towards interconnections between the anthroposphere and natural sphere.

PubMed

Körfgen, Annemarie; Keller, Lars; Kuthe, Alina; Oberrauch, Anna; Stötter, Hans

2017-02-15

The grand challenges of the 21st century will increasingly require societies to reconsider the pathways taken thus far. Engagement with climate change is of ever-growing importance to young people. They will be confronted with the effects of climate change throughout their entire lives and, as future decision-makers, they will vitally shape societal developments. Education will thus play a crucial role in the transformation to a sustainable society. In terms of awareness-raising, an important first step in preparing young people for the challenges of the 21st century is to understand what content is connected with climate change. As complex challenges, such as climate change, demand ways of thinking that go beyond categories, interconnections between the anthroposphere and the natural sphere have to be taken into consideration. This study provides an insight into the questions and topics young people develop whilst becoming involved in climate change in an in-school learning setting and in an out-of-school learning setting (a high mountain environment). The analysis focuses on the question of in which spheres students predominantly make their thematic choices and how far the interconnections between different spheres are formed. Our results show that the choice of the learning setting influences the topics students connect with climate change. Interconnections between sub-spheres of the anthroposphere and natural sphere are made only occasionally. These findings serve as a basis for reconsidering the content and foundation of climate change communication with young people. We recommend that climate change educational programmes should include phases that allow the following: a) involvement with climate change issues related to single spheres in the first phase, and b) consideration of the interconnections between spheres when becoming involved with climate change issues in the second phase. As the educational setting can considerably influence the focus of the learning process, it should be chosen thoughtfully. Copyright © 2016 Elsevier B.V. All rights reserved.

Packaging material for thin film lithium batteries

DOEpatents

Bates, John B.; Dudney, Nancy J.; Weatherspoon, Kim A.

1996-01-01

A thin film battery including components which are capable of reacting upon exposure to air and water vapor incorporates a packaging system which provides a barrier against the penetration of air and water vapor. The packaging system includes a protective sheath overlying and coating the battery components and can be comprised of an overlayer including metal, ceramic, a ceramic-metal combination, a parylene-metal combination, a parylene-ceramic combination or a parylene-metal-ceramic combination.

10 CFR 60.143 - Monitoring and testing waste packages.

Code of Federal Regulations, 2010 CFR

2010-01-01

... package monitoring program shall include laboratory experiments which focus on the internal condition of... the laboratory experiments. (d) The waste package monitoring program shall continue as long as...

10 CFR 60.143 - Monitoring and testing waste packages.

Code of Federal Regulations, 2011 CFR

2011-01-01

... package monitoring program shall include laboratory experiments which focus on the internal condition of... the laboratory experiments. (d) The waste package monitoring program shall continue as long as...

10 CFR 60.143 - Monitoring and testing waste packages.

Code of Federal Regulations, 2012 CFR

2012-01-01

... package monitoring program shall include laboratory experiments which focus on the internal condition of... the laboratory experiments. (d) The waste package monitoring program shall continue as long as...

10 CFR 60.143 - Monitoring and testing waste packages.

Code of Federal Regulations, 2013 CFR

2013-01-01

... package monitoring program shall include laboratory experiments which focus on the internal condition of... the laboratory experiments. (d) The waste package monitoring program shall continue as long as...

10 CFR 60.143 - Monitoring and testing waste packages.

Code of Federal Regulations, 2014 CFR

2014-01-01

... package monitoring program shall include laboratory experiments which focus on the internal condition of... the laboratory experiments. (d) The waste package monitoring program shall continue as long as...

Calculation of response matrix of CaSO 4:Dy based neutron dosimeter using Monte Carlo code FLUKA and measurement of 241Am-Be spectra

NASA Astrophysics Data System (ADS)

Chatterjee, S.; Bakshi, A. K.; Tripathy, S. P.

2010-09-01

Response matrix for CaSO 4:Dy based neutron dosimeter was generated using Monte Carlo code FLUKA in the energy range thermal to 20 MeV for a set of eight Bonner spheres of diameter 3-12″ including the bare one. Response of the neutron dosimeter was measured for the above set of spheres for 241Am-Be neutron source covered with 2 mm lead. An analytical expression for the response function was devised as a function of sphere mass. Using Frascati Unfolding Iteration Tool (FRUIT) unfolding code, the neutron spectrum of 241Am-Be was unfolded and compared with standard IAEA spectrum for the same.

Spectroscopic analysis and the excellent reusability of sphere-capped ferrocene in the oxidation of glucose oxidase.

PubMed

Antepli, Esin; Sarı, Nurşen

2016-08-01

Sphere-capped ferrocene nanospheres with Schiff base spacers have been prepared using a template, and used as carriers to immobilize glucose oxidase (GOx). GOx immobilized on spheres with one C-spacer (APS-Fc) exhibited high binding affinity to the substrate, which was attributed to appropriate position for the GOx conformation. When glucose oxidase was immobilized with spacers of different lengths, it was found that storage stability decreased with increasing the length of the spacer. It has been found that nanospheres, including capped ferrocene, exhibit good performance as the immobilized supporters of GOx. (APS-EtFc-GOx) retain more than 10% of the initial activity after forty-two successive cycles, which is a remarkable result.

Anhydrous Ammonia Training Module. Trainer's Package. Participant's Package.

ERIC Educational Resources Information Center

Beaudin, Bart; And Others

This document contains a trainer's and a participant's package for teaching employees on site safe handling procedures for working with anhydrous ammonia, especially on farms. The trainer's package includes the following: a description of the module; a competency; objectives; suggested instructional aids; a training outline (or lesson plan) for…

78 FR 32686 - Final Supplemental Environmental Impact Statement on the Issuance of Annual Regulations...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-31

... process. (2) Frequency of review and adoption of duck regulatory packages. Duck regulatory packages are the set of framework regulations that apply to the general duck hunting seasons. Packages include..., we present two alternatives regarding how frequently duck regulatory packages should be reviewed and...

Naval Meteorology and Oceanography Command exhibit

NASA Technical Reports Server (NTRS)

2000-01-01

Designed to entertain while educating, StenniSphere at the John C. Stennis Space Center in Hancock County, Miss., includes informative displays and exhibits from NASA and other agencies located at Stennis, such as this one from the Naval Meteorology and Oceanography Command. Visitors can 'travel' three-dimensionally under the sea and check on the weather back home in the Weather Center. StenniSphere is open free of charge from 9 a.m. to 5 p.m. daily.

iss055e008318

NASA Image and Video Library

2018-04-02

iss055e008318 (April 2, 2018) --- Expedition 55 Flight Engineer Drew Feustel works inside the Japanese Kibo laboratory module with tiny internal satellites known as SPHERES, or Synchronized Position Hold, Engage, Reorient, Experimental Satellites. Feustel was operating the SPHERES for the Smoothing-Based Relative Navigation (SmoothNav) experiment which is developing an algorithm to obtain the most probable estimate of the relative positions and velocities between all spacecraft using all available sensor information, including past measurements.

Nuclear spin relaxation in ligands outside of the first coordination sphere in a gadolinium (III) complex: Effects of intermolecular forces

NASA Astrophysics Data System (ADS)

Kruk, Danuta; Kowalewski, Jozef

2002-07-01

This article describes paramagnetic relaxation enhancement (PRE) in systems with high electron spin, S, where there is molecular interaction between a paramagnetic ion and a ligand outside of the first coordination sphere. The new feature of our treatment is an improved handling of the electron-spin relaxation, making use of the Redfield theory. Following a common approach, a well-defined second coordination sphere is assumed, and the PRE contribution from these more distant and shorter-lived ligands is treated in a way similar to that used for the first coordination sphere. This model is called "ordered second sphere," OSS. In addition, we develop here a formalism similar to that of Hwang and Freed [J. Chem. Phys. 63, 4017 (1975)], but accounting for the electron-spin relaxation effects. We denote this formalism "diffuse second sphere," DSS. The description of the dynamics of the intermolecular dipole-dipole interaction is based on the Smoluchowski equation, with a potential of mean force related to the radial distribution function. We have used a finite-difference method to calculate numerically a correlation function for translational motion, taking into account the intermolecular forces leading to an arbitrary radial distribution of the ligand protons. The OSS and DSS models, including the Redfield description of the electron-spin relaxation, were used to interpret the PRE in an aqueous solution of a slowly rotating gadolinium (III) complex (S=7/2) bound to a protein.

On the geometry dependence of differential pathlength factor for near-infrared spectroscopy. I. Steady-state with homogeneous medium

PubMed Central

Piao, Daqing; Barbour, Randall L.; Graber, Harry L.; Lee, Daniel C.

2015-01-01

Abstract. This work analytically examines some dependences of the differential pathlength factor (DPF) for steady-state photon diffusion in a homogeneous medium on the shape, dimension, and absorption and reduced scattering coefficients of the medium. The medium geometries considered include a semi-infinite geometry, an infinite-length cylinder evaluated along the azimuthal direction, and a sphere. Steady-state photon fluence rate in the cylinder and sphere geometries is represented by a form involving the physical source, its image with respect to the associated extrapolated half-plane, and a radius-dependent term, leading to simplified formula for estimating the DPFs. With the source-detector distance and medium optical properties held fixed across all three geometries, and equal radii for the cylinder and sphere, the DPF is the greatest in the semi-infinite and the smallest in the sphere geometry. When compared to the results from finite-element method, the DPFs analytically estimated for 10 to 25 mm source–detector separations on a sphere of 50 mm radius with μa=0.01  mm−1 and μs′=1.0  mm−1 are on average less than 5% different. The approximation for sphere, generally valid for a diameter ≥20 times of the effective attenuation pathlength, may be useful for rapid estimation of DPFs in near-infrared spectroscopy of an infant head and for short source–detector separation. PMID:26465613

Minimum initial service package (MISP) for sexual and reproductive health in disasters.

PubMed

Lisam, Suchitra

2014-12-01

This paper is based on a presentation given at the Evidence Aid Symposium, on 20 September 2014, at Hyderabad, India. The paper provides background about how the sexual and reproductive health (SRH) got conceived as a humanitarian health response that adopts human right approach, based on core principles driven by needs of adolescent girls and women, and having respect for their values, ethics and morals. Good practices across nations documented by Inter-Agency Working Groups (IAWGs) on Reproductive Health in Humanitarian Crisis has supported the provision of essential SRH care services to adolescent girls and women in humanitarian crisis and in disasters. Secondary desk review is used to document the lessons learnt and good practices followed and documents for SRH. These essential SRH care services are to be provided as "Minimum Initial Service Package (MISP)" for implementation at the outset of disaster. The Sphere Humanitarian Charter and Minimum Standards in Disaster Response incorporated the MISP for SRH as a minimum standard of care in disaster response with a goal to reduce mortality, morbidity and disability among populations affected by crises, particularly women and girls. Disaster prone countries are expected to roll out MISP to improve humanitarian response and emergency preparedness systems. The East Europe and Central Asia (EECA) region including India have rolled out MISP starting from 2011 (EECA) and from 2013-2014 onwards in India across cities such as Chennai, Patna, Bhubaneshwar, Kolkata, Faridabad and Calcutta. Across India, through these national and state level trainings, nearly 600 people from NGOs, institutions, and government agencies were developed as national level trainers and resource persons for MISP who could advocate for RH in emergencies, apply core techniques provided in the MISP, apply coordination skills for the implementation of MISP and develop an action plan to integrate RH and Gender Based Violence (GBV) into Disaster Management Plans of respective agencies. The way forward includes focusing on MISP distance learning module, integration of MISP in Health action plans, and integration into national disaster preparedness and contingency planning of respective agencies and departments and building capacity at various levels. © 2014 Chinese Cochrane Center, West China Hospital of Sichuan University and Wiley Publishing Asia Pty Ltd.

Impact of policy changes on infant feeding decisions among low-income women participating in the Special Supplemental Nutrition Program for Women, Infants, and Children.

PubMed

Whaley, Shannon E; Koleilat, Maria; Whaley, Mike; Gomez, Judy; Meehan, Karen; Saluja, Kiran

2012-12-01

We present infant feeding data before and after the 2009 Special Supplemental Nutrition Program for Women, Infants, and Children (WIC) food package change that supported and incentivized breastfeeding. We describe the key role of California WIC staff in supporting these policy changes. We analyzed WIC data on more than 180,000 infants in Southern California. We employed the analysis of variance and Tukey (honestly significant difference) tests to compare issuance rates of postpartum and infant food packages before and after the changes. We used analysis of covariance to adjust for poverty status changes as a potential confounder. Issuance rates of the "fully breastfeeding" package at infant WIC enrollment increased by 86% with the package changes. Rates also increased significantly for 2- and 6-month-old infants. Issuance rates of packages that included formula decreased significantly. All outcomes remained highly significant in the adjusted model. Policy changes, training of front-line WIC staff, and participant education influenced issuance rates of WIC food packages. In California, the issuance rates of packages that include formula have significantly decreased and the rate for those that include no formula has significantly increased.

How tobacco companies in the UK prepared for and responded to standardised packaging of cigarettes and rolling tobacco.

PubMed

Moodie, Crawford; Angus, Kathryn; Mitchell, Danielle; Critchlow, Nathan

2018-01-10

As a result of the Standardised Packaging of Tobacco Products Regulations and Tobacco Products Directive, all packs of cigarettes (factory-made and hand-rolled) in the UK must be drab brown, display pictorial warnings on the principal display areas and contain no less than 20 cigarettes or 30 g of tobacco. The legislation was phased in between May 2016 and May 2017. Our objective was to monitor pack, brand and product changes preimplementation and postimplementation. Our surveillance of the cigarette market involved a review of the trade press, a monthly monitor of online supermarkets and regular visits to stores, from May 2015 to June 2017. Before standardised packaging there were changes to the pack graphics (eg, redesigned packs and limited editions) and pack structure (eg, resealable inner foil) and the issue of a number of reusable tins. After standardised packaging, changes included newer cigarette pack sizes for some brand variants (eg, 23 and 24 packs). Changes to the branding prestandardised packaging included brand extensions, and poststandardised packaging included brand and/or variant name change, often with the inclusion of colour descriptors and brand migrations. Product changes prestandardised packaging included the introduction of novel filters (eg, filters with two flavour-changing capsules, tube filters, firmer filters and filters with granular additives). There was non-compliance with the legislation, with slim packs, which are not permitted, on sale after standardised packaging was implemented. Our findings highlight the need to monitor developments in markets introducing standardised packaging and have policy implications for countries considering this measure. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

AN ADA LINEAR ALGEBRA PACKAGE MODELED AFTER HAL/S

NASA Technical Reports Server (NTRS)

Klumpp, A. R.

1994-01-01

This package extends the Ada programming language to include linear algebra capabilities similar to those of the HAL/S programming language. The package is designed for avionics applications such as Space Station flight software. In addition to the HAL/S built-in functions, the package incorporates the quaternion functions used in the Shuttle and Galileo projects, and routines from LINPAK that solve systems of equations involving general square matrices. Language conventions in this package follow those of HAL/S to the maximum extent practical and minimize the effort required for writing new avionics software and translating existent software into Ada. Valid numeric types in this package include scalar, vector, matrix, and quaternion declarations. (Quaternions are fourcomponent vectors used in representing motion between two coordinate frames). Single precision and double precision floating point arithmetic is available in addition to the standard double precision integer manipulation. Infix operators are used instead of function calls to define dot products, cross products, quaternion products, and mixed scalar-vector, scalar-matrix, and vector-matrix products. The package contains two generic programs: one for floating point, and one for integer. The actual component type is passed as a formal parameter to the generic linear algebra package. The procedures for solving systems of linear equations defined by general matrices include GEFA, GECO, GESL, and GIDI. The HAL/S functions include ABVAL, UNIT, TRACE, DET, INVERSE, TRANSPOSE, GET, PUT, FETCH, PLACE, and IDENTITY. This package is written in Ada (Version 1.2) for batch execution and is machine independent. The linear algebra software depends on nothing outside the Ada language except for a call to a square root function for floating point scalars (such as SQRT in the DEC VAX MATHLIB library). This program was developed in 1989, and is a copyrighted work with all copyright vested in NASA.

User’s guide for GcClust—An R package for clustering of regional geochemical data

USGS Publications Warehouse

Ellefsen, Karl J.; Smith, David B.

2016-04-08

GcClust is a software package developed by the U.S. Geological Survey for statistical clustering of regional geochemical data, and similar data such as regional mineralogical data. Functions within the software package are written in the R statistical programming language. These functions, their documentation, and a copy of the user’s guide are bundled together in R’s unit of sharable code, which is called a “package.” The user’s guide includes step-by-step instructions showing how the functions are used to cluster data and to evaluate the clustering results. These functions are demonstrated in this report using test data, which are included in the package.

Navy Littoral Combat Ship (LCS) Program: Oversight Issues and Options for Congress

DTIC Science & Technology

2007-07-18

including unmanned vehicles (UVs). The basic version of the LCS, without any mission packages, is referred to as the LCS sea frame. The first LCS was...Littoral Combat Ship (LCS). The LCS is a small, fast ship that uses modular “plug-and- fight” mission packages, including unmanned vehicles (UVs). The...fight” mission packages, including unmanned vehicles (UVs). Rather than being a multimission ship like the Navy’s current large surface combatants

Interpretive video analyses of children's inquiry: Fantasy and other emergent contexts at a summer science camp for elementary school children

NASA Astrophysics Data System (ADS)

Beck, Diana Pyse

This study looks at learning contexts and the kinds of learning events that evolve out of a particular context. A former teacher and teacher educator spent several weeks each summer for three years at a Summer Science Camp (SSC) for children. The camp was designed to promote inquiry in science learning for both teachers and the young elementary school-age campers. For this study a group of four children was video taped and observed for two weeks during one of the summers. Using a constructivist approach, written transcripts, video tapes, and fieldnotes were subjected to several methods of analysis to develop an understanding of how the children worked together and apart during this time. Various constructs developed from data gathered in other summers were used to help develop an understanding of the events of the two weeks. Several new constructs for investigating children's learning in science are proposed in this study, including a construct or a unit of study for analyzing children's learning called "spheres of activity." Examinations of spheres include looking at the commonalities expressed by the children included in a sphere. One of these is the way language is used by members of a sphere. Another is the development of fantasies within the sphere or the way fantasies develop out of the activities. This includes how individual children contribute to fantasy constructions and the role that the development of fantasies plays in the children's inquiries into the science phenomena under investigation. Further analysis is done on the deep structures of those fantasies. In addition, the way children use tasks or develop tasks out of the projects assigned by teachers is examined as are the kinds of relationships the children have with the phenomena under investigation. This study enlarges and expands, not only the ways of thinking about and looking at children's science investigations, but also the language we are then able to use when investigating and describing children's learning. From this study, constructs for investigating the development of fantasies, i.e. invitations to fantasy, support for fantasies, extensions of fantasies, and fantasy "contexts" in addition to "spheres of activity" and their relationship to fantasy development have emerged. With these constructs questions can be asked that there was no language for before. In addition to developing the new constructs, investigating how they articulate with other SSC constructs--that is, modes of engagement, ways of working, and science "connections"--expands the field of science education.

Containers and Packaging: Product-Specific Data

EPA Pesticide Factsheets

This web page provide numbers on the different containers and packaging products in our municipal solid waste. These include containers of all types, such as glass, steel, plastic, aluminum, wood, and other types of packaging

Spelling for the Office. Competency Test Package. Office Occupations. Instructor's Guide.

ERIC Educational Resources Information Center

Hines, Donna

This competency test package, one of a series of test packages for office occupations education, contains a list of performance objectives; a pool of objective questions matched with these performance objectives; a sample, 50-point objective test; and several performance test activities. The package also includes complete directions for the…

Basic Skills for Word Processing. Competency Test Package. Office Occupations. Instructor's Guide.

ERIC Educational Resources Information Center

Hines, Donna

This competency test package, one of a series of test packages for office occupations education, contains a list of performance objectives; a pool of objective questions matched with these performance objectives; a sample, 50-point objective test; and several performance test activities. The package also includes complete directions for the…

Tractor Mechanics: Maintaining and Servicing the Fuel System. Learning Activity Packages 20-33.

ERIC Educational Resources Information Center

Clemson Univ., SC. Vocational Education Media Center.

Learning activity packages are presented for instruction in tractor mechanics. The packages deal with the duties involved in maintaining the fuel system. The following fourteen learning activity packages are included: servicing fuel and air filters, servicing fuel tanks and lines, adjusting a carburetor, servicing a carburetor, servicing the…

21 CFR 181.22 - Certain substances employed in the manufacture of food-packaging materials.

Code of Federal Regulations, 2011 CFR

2011-04-01

... food-packaging materials. 181.22 Section 181.22 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT... of food-packaging materials. Prior to the enactment of the food additives amendment to the Federal... manufacturing practice for food-packaging materials includes the restriction that the quantity of any of these...

Opportunities for cellulose nanomaterials in packaging films: a review and future trends

Treesearch

Nicole M. Stark

2016-01-01

Performance requirements for packaging films may include barrier properties, transparency, flexibility, and tensile strength. Conventional packaging materials such as plastic films and laminates, are typically made from petroleum-based polymers. Currently, there is a drive to develop sustainable packaging materials. These alternative materials must be able to be...

Business Telephone Etiquette. Comptetency Test Package. Office Occupations. Instructor's Guide.

ERIC Educational Resources Information Center

Hines, Donna

This competency test package, one of a series of test packages for office occupations education, contains a list of performance objectives: a sample, 50-point objective test; and several performance test activities. The package also includes complete directions for the student and the instructor, plus answer keys and a guide for evaluating the…

21 CFR 520.1720b - Phenylbutazone granules.

Code of Federal Regulations, 2013 CFR

2013-04-01

... phenylbutazone per package or 1 gram of phenylbutazone per package. (b) Sponsor. See 000061 in § 510.600(c) for 8-gram package, see 059320 for 1-gram package. (c) NAS/NRC status. The conditions of use have been NAS... include effectiveness data specified by § 514.111 of this chapter, but may require bioequivalency and...

21 CFR 520.1720b - Phenylbutazone granules.

Code of Federal Regulations, 2012 CFR

2012-04-01

... phenylbutazone per package or 1 gram of phenylbutazone per package. (b) Sponsor. See 000061 in § 510.600(c) for 8-gram package, see 059320 for 1-gram package. (c) NAS/NRC status. The conditions of use have been NAS... include effectiveness data specified by § 514.111 of this chapter, but may require bioequivalency and...

21 CFR 520.1720b - Phenylbutazone granules.

Code of Federal Regulations, 2010 CFR

2010-04-01

... phenylbutazone per package or 1 gram of phenylbutazone per package. (b) Sponsor. See 000061 in § 510.600(c) for 8-gram package, see 059320 for 1-gram package. (c) NAS/NRC status. The conditions of use have been NAS... include effectiveness data specified by § 514.111 of this chapter, but may require bioequivalency and...

21 CFR 520.1720b - Phenylbutazone granules.

Code of Federal Regulations, 2014 CFR

2014-04-01

... phenylbutazone per package or 1 gram of phenylbutazone per package. (b) Sponsor. See 000061 in § 510.600(c) for 8-gram package, see 059320 for 1-gram package. (c) NAS/NRC status. The conditions of use have been NAS... include effectiveness data specified by § 514.111 of this chapter, but may require bioequivalency and...

21 CFR 520.1720b - Phenylbutazone granules.

Code of Federal Regulations, 2011 CFR

2011-04-01

... phenylbutazone per package or 1 gram of phenylbutazone per package. (b) Sponsor. See 000061 in § 510.600(c) for 8-gram package, see 059320 for 1-gram package. (c) NAS/NRC status. The conditions of use have been NAS... include effectiveness data specified by § 514.111 of this chapter, but may require bioequivalency and...

Radio controlled release apparatus for animal data acquisition devices

DOEpatents

Stamps, James Frederick

2000-01-01

A novel apparatus for reliably and selectively releasing a data acquisition package from an animal for recovery. The data package comprises two parts: 1) an animal data acquisition device and 2) a co-located release apparatus. One embodiment, which is useful for land animals, the release apparatus includes two major components: 1) an electronics package, comprising a receiver; a decoder comparator, having at plurality of individually selectable codes; and an actuator circuit and 2) a release device, which can be a mechanical device, which acts to release the data package from the animal. To release a data package from a particular animal, a radio transmitter sends a coded signal which is decoded to determine if the code is valid for that animal data package. Having received a valid code, the release device is activated to release the data package from the animal for subsequent recovery. A second embodiment includes floatation means and is useful for releasing animal data acquisition devices attached to sea animals. This embodiment further provides for releasing a data package underwater by employing an acoustic signal.

CATPAC -- Catalogue Applications Package on UNIX

NASA Astrophysics Data System (ADS)

Wood, A. R.

CATPAC is the STARLINK Catalogue and Table Package. This document describes the CATPAC applications available on UNIX. These include applications for inputing, processing and reporting tabular data including astronomical catalogues.

Documentation of the Unsaturated-Zone Flow (UZF1) Package for modeling Unsaturated Flow Between the Land Surface and the Water Table with MODFLOW-2005

USGS Publications Warehouse

Niswonger, Richard G.; Prudic, David E.; Regan, R. Steven

2006-01-01

Percolation of precipitation through unsaturated zones is important for recharge of ground water. Rain and snowmelt at land surface are partitioned into different pathways including runoff, infiltration, evapotranspiration, unsaturated-zone storage, and recharge. A new package for MODFLOW-2005 called the Unsaturated-Zone Flow (UZF1) Package was developed to simulate water flow and storage in the unsaturated zone and to partition flow into evapotranspiration and recharge. The package also accounts for land surface runoff to streams and lakes. A kinematic wave approximation to Richards? equation is solved by the method of characteristics to simulate vertical unsaturated flow. The approach assumes that unsaturated flow occurs in response to gravity potential gradients only and ignores negative potential gradients; the approach further assumes uniform hydraulic properties in the unsaturated zone for each vertical column of model cells. The Brooks-Corey function is used to define the relation between unsaturated hydraulic conductivity and water content. Variables used by the UZF1 Package include initial and saturated water contents, saturated vertical hydraulic conductivity, and an exponent in the Brooks-Corey function. Residual water content is calculated internally by the UZF1 Package on the basis of the difference between saturated water content and specific yield. The UZF1 Package is a substitution for the Recharge and Evapotranspiration Packages of MODFLOW-2005. The UZF1 Package differs from the Recharge Package in that an infiltration rate is applied at land surface instead of a specified recharge rate directly to ground water. The applied infiltration rate is further limited by the saturated vertical hydraulic conductivity. The UZF1 Package differs from the Evapotranspiration Package in that evapotranspiration losses are first removed from the unsaturated zone above the evapotranspiration extinction depth, and if the demand is not met, water can be removed directly from ground water whenever the depth to ground water is less than the extinction depth. The UZF1 Package also differs from the Evapotranspiration Package in that water is discharged directly to land surface whenever the altitude of the water table exceeds land surface. Water that is discharged to land surface, as well as applied infiltration in excess of the saturated vertical hydraulic conductivity, may be routed directly as inflow to specified streams or lakes if these packages are active; otherwise, this water is removed from the model. The UZF1 Package was tested against the U.S. Geological Survey's Variably-Saturated Two-Dimensional Flow and Transport Model for a vertical unsaturated flow problem that includes evapotranspiration losses. This report also includes an example in which MODFLOW-2005 with the UZF1 Package was used to simulate a realistic surface-water/ground-water flow problem that includes time and space variable infiltration, evapotranspiration, runoff, and ground-water discharge to land surface and to streams. Another simpler problem is presented so that the user may use the input files as templates for new problems and to verify proper code installation.

Detection of biological particles by the use of circular dichroism measurements improved by scattering theory

NASA Astrophysics Data System (ADS)

Rosen, David L.; Pendleton, J. David

1995-09-01

Light scattered from optically active spheres was theoretically analyzed for biodetection. The circularly polarized signal of near-forward scattering from circularly dichroic spheres was calculated. Both remote and point biodetection were considered. The analysis included the effect of a circular aperture and beam block at the detector. If the incident light is linearly polarized, a false signal would limit the sensitivity of the biodetector. If the incident light is randomly polarized, shot noise would limit the sensitivity. Suggested improvements to current techniques include a beam block, precise angular measurements, randomly polarized light, index-matching fluid, and larger apertures for large particles.

Creative Thinking Package

ERIC Educational Resources Information Center

Jones, Clive

1972-01-01

A look at the latest package from a British managment training organization, which explains and demonstrates creative thinking techniques, including brainstorming. The package, designed for groups of twelve or more, consists of tapes, visuals, and associated exercises. (Editor/JB)

Comparative Packaging Study

NASA Technical Reports Server (NTRS)

Perchonok, Michele; Antonini, David

2008-01-01

This viewgraph presentation describes a comparative packaging study for use on long duration space missions. The topics include: 1) Purpose; 2) Deliverables; 3) Food Sample Selection; 4) Experimental Design Matrix; 5) Permeation Rate Comparison; and 6) Packaging Material Information.

Naval Meteorology and Oceanography Command exhibit entrance

NASA Technical Reports Server (NTRS)

2000-01-01

StenniSphere at NASA's John C. Stennis Space Center in Hancock County, Miss., invites visitors to discover why America comes to Stennis Space Center before going into space. Designed to entertain while educating, StenniSphere includes informative displays and exhibits from NASA and other agencies located at Stennis, such as this one from the Naval Meteorology and Oceanography Command. Visitors can 'travel' three-dimensionally under the sea and check on the weather back home in the Weather Center.

Electrical Properties and Manufacturability of ITO-MgF2 and Related Transparent Arcproof Spacecraft Coatings

NASA Technical Reports Server (NTRS)

Hambourger, Paul D.

2003-01-01

To investigate the applicability of co-deposited indium tin oxide and magnesium fluoride as a transparent arcproof coating on the exterior of PowerSphere microsatellites. This included testing coating performance after deposition on flexible polymeric substrates, determining whether ultraviolet (UV) radiation present during deposition might affect the UV-curing resin contained in the substrate, and preparation of coated polymeric samples for radiation damage studies by the PowerSphere team.

Modular avionics packaging standardization

NASA Astrophysics Data System (ADS)

Austin, M.; McNichols, J. K.

The Modular Avionics Packaging (MAP) Program for packaging future military avionics systems with the objective of improving reliability, maintainability, and supportability, and reducing equipment life cycle costs is addressed. The basic MAP packaging concepts called the Standard Avionics Module, the Standard Enclosure, and the Integrated Rack are summarized, and the benefits of modular avionics packaging, including low risk design, technology independence with common functions, improved maintainability and life cycle costs are discussed. Progress made in MAP is briefly reviewed.

Transformation of food packaging from passive to innovative via nanotechnology: concepts and critiques.

PubMed

Mlalila, Nichrous; Kadam, Dattatreya M; Swai, Hulda; Hilonga, Askwar

2016-09-01

In recent decades, there is a global advancement in manufacturing industry due to increased applications of nanotechnology. Food industry also has been tremendously changing from passive packaging to innovative packaging, to cope with global trends, technological advancements, and consumer preferences. Active research is taking place in food industry and other scientific fields to develop innovative packages including smart, intelligent and active food packaging for more effective and efficient packaging materials with balanced environmental issues. However, in food industry the features behind smart packaging are narrowly defined to be distinguished from intelligent packaging as in other scientific fields, where smart materials are under critical investigations. This review presents some scientific concepts and features pertaining innovative food packaging. The review opens new research window in innovative food packaging to cover the existing disparities for further precise research and development of food packaging industry.

Water Surface Impact and Ricochet of Deformable Elastomeric Spheres

NASA Astrophysics Data System (ADS)

Hurd, Randy C.

Soft and deformable silicone rubber spheres ricochet from a water surface when rigid spheres and disks (or skipping stones) cannot. This dissertation investigates why these objects are able to skip so successfully. High speed cameras allow us to see that these unique spheres deform significantly as they impact the water surface, flattening into pancake-like shapes with greater area. Though the water entry behavior of deformable spheres deviates from that of rigid spheres, our research shows that if this deformation is accounted for, their behavior can be predicted from previously established methods. Soft spheres skip more easily because they deform significantly when impacting the water surface. We present a diagram which enables the prediction of a ricochet from sphere impact conditions such as speed and angle. Experiments and mathematical representations of the sphere skipping both show that these deformable spheres skip more readily because deformation momentarily increases sphere area and produces an attack angle with the water which is favorable to skipping. Predictions from our mathematical representation of sphere skipping agree strongly with observations from experiments. Even when a sphere was allowed to skip multiple times in the laboratory, the mathematical predictions show good agreement with measured impact conditions through subsequent skipping events. While studying multiple impact events in an outdoor setting, we discovered a previously unidentified means of skipping, which is unique to deformable spheres. This new skipping occurs when a relatively soft sphere first hits the water at a high speed and low impact angle and the sphere begins to rotate very quickly. This quick rotation causes the sphere to stretch into a shape similar to an American football and maintain this shape while it spins. The sphere is observed to move nearly parallel with the water surface with the tips of this "football" dipping into the water as it rotates and the sides passing just over the surface. This sequence of rapid impact events give the impression that the sphere is walking across the water surface.

Entity- Version 1.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hart, Brian; Oppel, Fred; Rigdon, Brian

2012-09-13

This package contains classes that capture high-level aspects of characters and vehicles. Vehicles manage seats and riders. Vehicles and characters now can be configured to compose different behaviors and have certain capabilities, by adding them through xml data. These behaviors and capabilities are not included in this package, but instead are part of other packages such as mobility behavior, path planning, sight, sound. Entity is not dependent on these other packages. This package also contains the icons used for Umbra applications Dante Scenario Editor, Dante Tabletop and OpShed. This assertion includes a managed C++ wrapper code (EntityWrapper) to enable C#more » applications, such as Dante Scenario Editor, Dante Tabletop, and OpShed, to incorporate this library.« less

Novel morphology of calcium carbonate controlled by poly(L-lysine).

PubMed

Yao, Yuan; Dong, Wenyong; Zhu, Shenmin; Yu, Xinhai; Yan, Deyue

2009-11-17

The novel calcium carbonate (CaCO(3)) morphology, twin-sphere with an equatorial girdle, has been obtained under the control of poly(L-lysine) (PLys) through gas-diffusion method. The effect of the concentration of calcium cation and PLys, the reaction time, and the initial pH value are investigated, and various interesting morphologies, including twin-sphere, discus-like, hexagonal plate, and hallow structure are observed by using scanning electronic microscopy. Laser microscopic Raman spectroscopy studies indicated that all these CaCO(3) are vaterite. A possible mechanism is suggested to explain the formation of the twin-sphere based morphologies according to the results. It is proven that alkaline polypeptides can control the mineralization of CaCO(3) precisely as the reported acidic polypeptides and double hydrophilic block copolymers.

Science on a Sphere and Data in the Classroom: A Marriage Between Limitless Learning Experiences.

NASA Astrophysics Data System (ADS)

Zepecki, S., III; Dean, A. F.; Pisut, D.

2017-12-01

NOAA and other agencies have contributed significantly to the creation and distribution of educational materials to enhance the public understanding of the interconnectedness of the Earth processes and human activities. Intended for two different learning audiences, Science on a Sphere and Data in the Classroom are both educational tools used to enhance understanding of our world and how human activity influences change. Recently, NOAA has undertaken the task of marrying Data in the Classroom's NGSS aligned curriculum, which includes topics such as El Niño, sea level rise, and coral bleaching, with Science on a Sphere's Earth and space data visualization exhibits. This partnership allows for the fluidity of NOAA's data-driven learning materials, and fosters the homogeneity of formal and informal learning experiences for varied audiences.

Acoustic radiation force on a heated sphere including effects of heat transfer and acoustic streaming

NASA Technical Reports Server (NTRS)

Lee, Chun P.; Wang, Taylor G.

1988-01-01

A previous theoretical result on the subject of the acoustic radiation force on a heated sphere (Lee and Wang, 1984) is reexamined. For a more complete understanding, effects of heat transfer and acoustic streaming are taken into consideration. Essentially, it was found that, at high sound-pressure levels in a steady situation, the force is not affected significantly by the temperature profile, consistent with the result of an experimental work (Leung and Wang, 1985). This resolves the earlier apparent contradiction between the theory and the experiment. If excessive hot air is accumulated around the sphere, which can happen in transient situations, the force can be weakened or reversed in sign. A heat transfer model due to acoustic streaming was also found.

Collinear swimmer propelling a cargo sphere at low Reynolds number.

PubMed

Felderhof, B U

2014-11-01

The swimming velocity and rate of dissipation of a linear chain consisting of two or three little spheres and a big sphere is studied on the basis of low Reynolds number hydrodynamics. The big sphere is treated as a passive cargo, driven by the tail of little spheres via hydrodynamic and direct elastic interaction. The fundamental solution of Stokes equations in the presence of a sphere with a no-slip boundary condition, as derived by Oseen, is used to model the hydrodynamic interactions between the big sphere and the little spheres.

Self-assembled fibre optoelectronics with discrete translational symmetry

PubMed Central

Rein, Michael; Levy, Etgar; Gumennik, Alexander; Abouraddy, Ayman F.; Joannopoulos, John; Fink, Yoel

2016-01-01

Fibres with electronic and photonic properties are essential building blocks for functional fabrics with system level attributes. The scalability of thermal fibre drawing approach offers access to large device quantities, while constraining the devices to be translational symmetric. Lifting this symmetry to create discrete devices in fibres will increase their utility. Here, we draw, from a macroscopic preform, fibres that have three parallel internal non-contacting continuous domains; a semiconducting glass between two conductors. We then heat the fibre and generate a capillary fluid instability, resulting in the selective transformation of the cylindrical semiconducting domain into discrete spheres while keeping the conductive domains unchanged. The cylindrical-to-spherical expansion bridges the continuous conducting domains to create ∼104 self-assembled, electrically contacted and entirely packaged discrete spherical devices per metre of fibre. The photodetection and Mie resonance dependent response are measured by illuminating the fibre while connecting its ends to an electrical readout. PMID:27698454

Self-assembled fibre optoelectronics with discrete translational symmetry.

PubMed

Rein, Michael; Levy, Etgar; Gumennik, Alexander; Abouraddy, Ayman F; Joannopoulos, John; Fink, Yoel

2016-10-04

Fibres with electronic and photonic properties are essential building blocks for functional fabrics with system level attributes. The scalability of thermal fibre drawing approach offers access to large device quantities, while constraining the devices to be translational symmetric. Lifting this symmetry to create discrete devices in fibres will increase their utility. Here, we draw, from a macroscopic preform, fibres that have three parallel internal non-contacting continuous domains; a semiconducting glass between two conductors. We then heat the fibre and generate a capillary fluid instability, resulting in the selective transformation of the cylindrical semiconducting domain into discrete spheres while keeping the conductive domains unchanged. The cylindrical-to-spherical expansion bridges the continuous conducting domains to create ∼10 4 self-assembled, electrically contacted and entirely packaged discrete spherical devices per metre of fibre. The photodetection and Mie resonance dependent response are measured by illuminating the fibre while connecting its ends to an electrical readout.

Columbia, OV-102, forward middeck locker experiments and meal tray assemblies

NASA Technical Reports Server (NTRS)

1982-01-01

Overall view of forward middeck locker shows Continuous Flow Electrophoresis System (CFES) experiment control and monitoring module and sample storage module (on port side) and Monodisperse Latex Reactor (MLR) (on starboard side). Water Dispenser Kit water gun (above CFES module) and meal tray assemblies covered with snack food packages and beverage containers appear around the two experiments. Thanks to a variety of juices and other food items, this array in the middeck probably represents the most colorful area onboard the Earth-orbiting Columbia, Orbiter Vehicle (OV) 102. Most of the meal items have been carefully fastened to meal tray assemblies (foodtrays) and locker doors (or both). What has not been attached by conventional methods has been safely 'tucked' under something heavy (note jacket shoved into space occupied MLR). MLR is making its second flight and is designed to test the flexibility of making large-size, monodisperse (same size), polystyrene latex micro-spheres using

Impact of Policy Changes on Infant Feeding Decisions Among Low-Income Women Participating in the Special Supplemental Nutrition Program for Women, Infants, and Children

PubMed Central

Koleilat, Maria; Whaley, Mike; Gomez, Judy; Meehan, Karen; Saluja, Kiran

2012-01-01

Objectives. We present infant feeding data before and after the 2009 Special Supplemental Nutrition Program for Women, Infants, and Children (WIC) food package change that supported and incentivized breastfeeding. We describe the key role of California WIC staff in supporting these policy changes. Methods. We analyzed WIC data on more than 180 000 infants in Southern California. We employed the analysis of variance and Tukey (honestly significant difference) tests to compare issuance rates of postpartum and infant food packages before and after the changes. We used analysis of covariance to adjust for poverty status changes as a potential confounder. Results. Issuance rates of the “fully breastfeeding” package at infant WIC enrollment increased by 86% with the package changes. Rates also increased significantly for 2- and 6-month-old infants. Issuance rates of packages that included formula decreased significantly. All outcomes remained highly significant in the adjusted model. Conclusions. Policy changes, training of front-line WIC staff, and participant education influenced issuance rates of WIC food packages. In California, the issuance rates of packages that include formula have significantly decreased and the rate for those that include no formula has significantly increased. PMID:23078467

On the Effect of Sphere-Overlap on Super Coarse-Grained Models of Protein Assemblies

NASA Astrophysics Data System (ADS)

Degiacomi, Matteo T.

2018-05-01

Ion mobility mass spectrometry (IM/MS) can provide structural information on intact protein complexes. Such data, including connectivity and collision cross sections (CCS) of assemblies' subunits, can in turn be used as a guide to produce representative super coarse-grained models. These models are constituted by ensembles of overlapping spheres, each representing a protein subunit. A model is considered plausible if the CCS and sphere-overlap levels of its subunits fall within predetermined confidence intervals. While the first is determined by experimental error, the latter is based on a statistical analysis on a range of protein dimers. Here, we first propose a new expression to describe the overlap between two spheres. Then we analyze the effect of specific overlap cutoff choices on the precision and accuracy of super coarse-grained models. Finally, we propose a method to determine overlap cutoff levels on a per-case scenario, based on collected CCS data, and show that it can be applied to the characterization of the assembly topology of symmetrical homo-multimers. [Figure not available: see fulltext.

Confined Assembly of Hollow Carbon Spheres in Carbonaceous Nanotube: A Spheres-in-Tube Carbon Nanostructure with Hierarchical Porosity for High-Performance Supercapacitor.

PubMed

Chen, Ze; Ye, Sunjie; Evans, Stephen D; Ge, Yuanhang; Zhu, Zhifeng; Tu, Yingfeng; Yang, Xiaoming

2018-05-01

Carbonaceous nanotubes (CTs) represent one of the most popular and effective carbon electrode materials for supercapacitors, but the electrochemistry performance of CTs is largely limited by their relatively low specific surface area, insufficient usage of intratube cavity, low content of heteroatom, and poor porosity. An emerging strategy for circumventing these issues is to design novel porous CT-based nanostructures. Herein, a spheres-in-tube nanostructure with hierarchical porosity is successfully engineered, by encapsulating heteroatom-doping hollow carbon spheres into one carbonaceous nanotube (HCSs@CT). This intriguing nanoarchitecture integrates the merits of large specific surface area, good porosity, and high content of heteroatoms, which synergistically facilitates the transportation and exchange of ions and electrons. Accordingly, the as-prepared HCSs@CTs possess outstanding performances as electrode materials of supercapacitors, including superior capacitance to that of CTs, HCSs, and their mixtures, coupled with excellent cycling life, demonstrating great potential for applications in energy storage. © 2018 The Authors. Published by WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Effective conductivity of suspensions of hard spheres by Brownian motion simulation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chan Kim, I.; Torquato, S.

1991-02-15

A generalized Brownian motion simulation technique developed by Kim and Torquato (J. Appl. Phys. {bold 68}, 3892 (1990)) is applied to compute exactly'' the effective conductivity {sigma}{sub {ital e}} of heterogeneous media composed of regular and random distributions of hard spheres of conductivity {sigma}{sub 2} in a matrix of conductivity {sigma}{sub 1} for virtually the entire volume fraction range and for several values of the conductivity ratio {alpha}={sigma}{sub 2}/{sigma}{sub 1}, including superconducting spheres ({alpha}={infinity}) and perfectly insulating spheres ({alpha}=0). A key feature of the procedure is the use of {ital first}-{ital passage}-{ital time} equations in the two homogeneous phases andmore » at the two-phase interface. The method is shown to yield {sigma}{sub {ital e}} accurately with a comparatively fast execution time. The microstructure-sensitive analytical approximation of {sigma}{sub {ital e}} for dispersions derived by Torquato (J. Appl. Phys. {bold 58}, 3790 (1985)) is shown to be in excellent agreement with our data for random suspensions for the wide range of conditions reported here.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Melo, Ronaldo P. de; Colégio Militar do Recife, Exército Brasileiro, Recife PE 50730-120; Oliveira, Nathalia Talita C.

A novel procedure based on a two-step method was developed to obtain β-Ga{sub 2}O{sub 3} nanowires by the chemical vapor deposition (CVD) method. The first step consists in the gallium micro-spheres growth inside a metal-organic chemical vapor deposition environment, using an organometallic precursor. Nanoscale spheres covering the microspheres were obtained. The second step involves the CVD oxidization of the gallium micro-spheres, which allow the formation of β-Ga{sub 2}O{sub 3} nanowires on the micro-sphere surface, with the final result being a nanostructure mimicking nature's sea urchin morphology. The grown nanomaterial is characterized by several techniques, including X-ray diffraction, scanning electron microscopy,more » energy-dispersive X-ray, transmission electron microscopy, and photoluminescence. A discussion about the growth mechanism and the optical properties of the β-Ga{sub 2}O{sub 3} material is presented considering its unknown true bandgap value (extending from 4.4 to 5.68 eV). As an application, the scattering properties of the nanomaterial are exploited to demonstrate random laser emission (around 570 nm) when it is permeated with a laser dye liquid solution.« less

Inverse Magnus force in free molecular flow

NASA Astrophysics Data System (ADS)

Herczynski, A.; Weidman, P.

2003-11-01

The sidewise force on a spinning sphere translating in a rarified gas is calculated assuming that the flow can be treated as a stream of free molecules. This approach was first introduced by Newton in his investigation of the drag force. While it is not fruitful at subsonic flows in normal conditions, it gives remarkably accurate results at hypersonic speeds. Here it is applied to the high Knudsen number flow over spinning spheres, cylinders, cubes and more generally any spinning parallelepiped. In all cases, the force is in the opposite direction to that of the classical Magnus effect in continuum flow. The simple calculation for a sphere reproduces the isothermal result obtained recently by Borg, et al. (Phys. Fluids, 15, 2003) using Maxwellian distribution functions. For any parallelepiped, including the cube, just like for the sphere and the cylinder, the force is shown to be steady. In each of these, the magnitude of the inverse Magnus force is proprtional to the product of the angular speed, translational speed, and the mas of the gas displaced by the object.

Photothermal therapy of Lewis lung carcinoma in mice using gold nanoshells on carboxylated polystyrene spheres

NASA Astrophysics Data System (ADS)

Liu, Huiyu; Chen, Dong; Tang, Fangqiong; Du, Gangjun; Li, Linlin; Meng, Xianwei; Liang, Wei; Zhang, Yangde; Teng, Xu; Li, Yi

2008-11-01

A new approach towards the design of gold nanoshells on carboxylated polystyrene spheres (GNCPSs) is reported here. Gold nanoshells were self-assembled on the surface of carboxylated polystyrene spheres by a seed growth method. Chitosan (CHI) was used as a functional agent of carboxylated polystyrene spheres for attaching gold seeds. The surface plasmon resonance (SPR) peak of GNCPSs can be tuned, greatly redshifted, over a broad spectral range including the near-infrared (NIR) wavelength region, which provides maximal penetration of light through tissue. Irradiation of GNCPSs at their peak extinction coefficient results in the conversion of light to heat energy that produces a local rise in temperature. Our study revealed that the Lewis lung carcinoma (LLC) in mice treated with GNCPSs exposed to a low dose of NIR light (808 nm, 4 W cm-2) induced irreversible tissue damage. The tumor volumes of the treatment group by GNCPSs were significantly lower than those of control groups, with an average inhibition rate over 55% (P<0.005). This study proves that GNCPSs are promising in plasmonic photothermal tumor therapy.

Controllable synthesis of nitrogen-doped hollow mesoporous carbon spheres using ionic liquids as template for supercapacitors

NASA Astrophysics Data System (ADS)

Chen, Aibing; Li, Yunqian; Liu, Lei; Yu, Yifeng; Xia, Kechan; Wang, Yuying; Li, Shuhui

2017-01-01

We have demonstrated a facile and controllable synthesis of monodispersed nitrogen-doped hollow mesoporous carbon spheres (N-HMCSs) using resorcinol/formaldehyde resin as a carbon precursor, tetraethyl orthosilicate as a structure-assistant agent, ionic liquids (ILs) as soft template, partial carbon sources, and nitrogen sources. The sizes and the architectures including hollow and yolk-shell of resultant carbon spheres can be efficiently controlled through the adjustment of the content of ILs. Alkyl chain length of the ILs also has an important effect on the formation of N-HMCSs. With proper alkyl chain length and content of ILs, the resultant N-HMCSs show monodispersed hollow spheres with high surface areas (up to 1158 m2 g-1), large pore volumes (up to 1.70 cm3 g-1), and uniform mesopore size (5.0 nm). Combining the hollow mesoporous structure, high porosity, large surface area, and nitrogen functionality, the as-synthesized N-HMCSs have good supercapacitor performance with good capacitance (up to 159 F g-1) and favorable capacitance retention (88% capacitive retention after 5000 cycles).

The effect of ultrasound irradiation on the convective heat transfer rate during immersion cooling of a stationary sphere.

PubMed

Kiani, Hossein; Sun, Da-Wen; Zhang, Zhihang

2012-11-01

It has been proven that ultrasound irradiation can enhance the rate of heat transfer processes. The objective of this work was to study the heat transfer phenomenon, mainly the heat exchange at the surface, as affected by ultrasound irradiation around a stationary copper sphere (k=386W m(-1)K(-1), C(p)=384J kg(-1)K(-1), ρ=8660kg m(-3)) during cooling. The sphere (0.01m in diameter) was immersed in an ethylene glycol-water mixture (-10°C) in an ultrasonic cooling system that included a refrigerated circulator, a flow meter, an ultrasound generator and an ultrasonic bath. The temperature of the sphere was recorded using a data logger equipped with a T-type thermocouple in the center of the sphere. The temperature of the cooling medium was also monitored by four thermocouples situated at different places in the bath. The sphere was located at different positions (0.02, 0.04 and 0.06m) above the transducer surface of the bath calculated considering the center of the sphere as the center of the reference system and was exposed to different intensities of ultrasound (0, 120, 190, 450, 890, 1800, 2800, 3400 and 4100W m(-2)) during cooling. The frequency of the ultrasound was 25kHz. It was demonstrated that ultrasound irradiation can increase the rate of heat transfer significantly, resulting in considerably shorter cooling times. Higher intensities caused higher cooling rates, and Nu values were increased from about 23-27 to 25-108 depending on the intensity of ultrasound and the position of the sphere. However, high intensities of ultrasound led to the generation of heat at the surface of the sphere, thus limiting the lowest final temperature achieved. An analytical solution was developed considering the heat generation and was fitted to the experimental data with R(2) values in the range of 0.910-0.998. Visual observations revealed that both cavitation and acoustic streaming were important for heat transfer phenomenon. Cavitation clouds at the surface of the sphere were the main cause of heating effect. The results showed that closer distances to the transducer surface showed higher cooling rates. On the other hand, despite having a bigger distance from the transducer, when the sphere was located close to the gas-liquid interface the enhancement factor of heat transfer was higher. Ultrasound irradiation showed promising effect for the enhancement of convective heat transfer rate during immersion cooling. More investigations are required to demonstrate the behavior of ultrasound assisted heat transfer and resolve the proper way of the application of ultrasound to assist the cooling and/or freezing processes. Copyright © 2012 Elsevier B.V. All rights reserved.

Stem/progenitor cells derived from the cochlear sensory epithelium give rise to spheres with distinct morphologies and features.

PubMed

Diensthuber, Marc; Oshima, Kazuo; Heller, Stefan

2009-06-01

Nonmammalian vertebrates regenerate lost sensory hair cells by means of asymmetric division of supporting cells. Inner ear or lateral line supporting cells in birds, amphibians, and fish consequently serve as bona fide stem cells resulting in high regenerative capacity of hair cell-bearing organs. Hair cell regeneration does not happen in the mammalian cochlea, but cells with proliferative capacity can be isolated from the neonatal cochlea. These cells have the ability to form clonal floating colonies, so-called spheres, when cultured in nonadherent conditions. We noticed that the sphere population derived from mouse cochlear sensory epithelium cells was heterogeneous, consisting of morphologically distinct sphere types, hereby classified as solid, transitional, and hollow. Cochlear sensory epithelium-derived stem/progenitor cells initially give rise to small solid spheres, which subsequently transition into hollow spheres, a change that is accompanied by epithelial differentiation of the majority of sphere cells. Only solid spheres, and to a lesser extent, transitional spheres, appeared to harbor self-renewing stem cells, whereas hollow spheres could not be consistently propagated. Solid spheres contained significantly more rapidly cycling Pax-2-expressing presumptive otic progenitor cells than hollow spheres. Islet-1, which becomes upregulated in nascent sensory patches, was also more abundant in solid than in hollow spheres. Likewise, hair cell-like cells, characterized by the expression of multiple hair cell markers, differentiated in significantly higher numbers in cell populations derived from solid spheres. We conclude that cochlear sensory epithelium cell populations initially give rise to small solid spheres that have self-renewing capacity before they subsequently convert into hollow spheres, a process that is accompanied by loss of stemness and reduced ability to spontaneously give rise to hair cell-like cells. Solid spheres might, therefore, represent the most suitable sphere type for cell-based assays or animal model transplantation studies aimed at development of cell replacement therapies.

A Comparison of Priority-based and Incremental Real-Time Garbage Collectors in the Implementation of the Shadow Design Pattern

DTIC Science & Technology

2008-08-15

running the real-time application we used in our previous study on IBM WebSphere Real Time. IBM WebSphere Real Time automatically sets Metronome , its...the experiment show that the modified code for the Shadow Design Pattern runs well under Metronome . 15. NUMBER OF PAGES 25 14. SUBJECT TERMS...includes the real-time garbage collector called the Metronome . Unlike the Sun RTGC, we cannot change the priority of the Metronome RTGC. Metronome is

Apollo 15 green glasses.

NASA Technical Reports Server (NTRS)

Ridley, W. I.; Reid, A. M.; Warner, J. L.; Brown, R. W.

1973-01-01

The samples analyzed include 28 spheres, portions of spheres, and angular fragments from soil 15101. Emerald green glasses from other soils are identical to those from 15101. The composition of the green glass is unlike that of any other major lunar glass group. The Fe content is comparable to that in mare basalts, but Ti is much lower. The Mg content is much higher than in most lunar materials analyzed to date, and the Cr content is also high. The low Al content is comparable to that of mare basalt glasses.

Computational analysis of non-spherical particle transport and deposition in shear flow with application to lung aerosol dynamics--a review.

PubMed

Kleinstreuer, Clement; Feng, Yu

2013-02-01

All naturally occurring and most man-made solid particles are nonspherical. Examples include air-pollutants in the nano- to micro-meter range as well as blood constituents, drug particles, and industrial fluid-particle streams. Focusing on the modeling and simulation of inhaled aerosols, theories for both spherical and nonspherical particles are reviewed to analyze the contrasting transport and deposition phenomena of spheres and equivalent spheres versus ellipsoids and fibers.

Diagnostic packages can be assigned accurately in emergency departments. A multi-centre cohort study.

PubMed

Nørgaard, Birgitte; Mogensen, Christian Backer; Teglbjærg, Lars Stubbe; Brabrand, Mikkel; Lassen, Annmarie Touborg

2016-06-01

In the Region of Southern Denmark, the emergency departments categorise patients based on presenting symptoms and a proposed diagnostic package (n = 40) within each category. The diagnostic packages describe relevant clinical information and standard laboratory and other investigations to be performed. Allocation to the right diagnostic package is assumed to be associated with a higher quality. The aim of this study was to describe to which degree the assigned symptom-based diagnostic packages are related to relevant discharge diagnoses. This was a descriptive cohort study. The analysis was based on data on assigned diagnostic package, patient discharge diagnosis, hospital, gender, age, time of admission and discharge, length of stay, diagnostic package assigned, discharge diagnosis and co-morbidity. An acceptable standard for what would be an appropriate primarily diagnostic package was developed using a modified Delphi method. A total of 16,543 patient contacts were identified. Women constituted 52.2% (n = 8,925) of the patients. The median age was 64 years and the median length of stay was one day. All diagnostic packages were represented. A total of 68% of the included patients had been assigned an acceptable diagnostic package (95% confidence interval: 67.2-68.7). We found an appropriate use of one of 30 diagnostic packages in more than 50% of the cases. We found that 68% of the included patients were assigned an acceptable diagnostic package and that about 80% of all acute pathways were covered by 14 diagnostic packages. The study was funded by Region of Southern Denmark. The study was registered with the Danish Data Protection Agency (No. 2008-58-0035). No further approval was required.

NOAA's Science On a Sphere Education Program: Application of a Scientific Visualization System to Teach Earth System Science and Improve our Understanding About Creating Effective Visualizations

NASA Astrophysics Data System (ADS)

McDougall, C.; McLaughlin, J.

2008-12-01

NOAA has developed several programs aimed at facilitating the use of earth system science data and data visualizations by formal and informal educators. One of them, Science On a Sphere, a visualization display tool and system that uses networked LCD projectors to display animated global datasets onto the outside of a suspended, 1.7-meter diameter opaque sphere, enables science centers, museums, and universities to display real-time and current earth system science data. NOAA's Office of Education has provided grants to such education institutions to develop exhibits featuring Science On a Sphere (SOS) and create content for and evaluate audience impact. Currently, 20 public education institutions have permanent Science On a Sphere exhibits and 6 more will be installed soon. These institutions and others that are working to create and evaluate content for this system work collaboratively as a network to improve our collective knowledge about how to create educationally effective visualizations. Network members include other federal agencies, such as, NASA and the Dept. of Energy, and major museums such as Smithsonian and American Museum of Natural History, as well as a variety of mid-sized and small museums and universities. Although the audiences in these institutions vary widely in their scientific awareness and understanding, we find there are misconceptions and lack of familiarity with viewing visualizations that are common among the audiences. Through evaluations performed in these institutions we continue to evolve our understanding of how to create content that is understandable by those with minimal scientific literacy. The findings from our network will be presented including the importance of providing context, real-world connections and imagery to accompany the visualizations and the need for audience orientation before the visualizations are viewed. Additionally, we will review the publicly accessible virtual library housing over 200 datasets for SOS and any other real or virtual globe. These datasets represent contributions from NOAA, NASA, Dept. of Energy, and the public institutions that are displaying the spheres.

Radiometric Measurement Comparisons Using Transfer Radiometers in Support of the Calibration of NASA's Earth Observing System (EOS) Sensors

NASA Technical Reports Server (NTRS)

Butler, James J.; Johnson, B. Carol; Brown, Steven W.; Yoon, Howard W.; Barnes, Robert A.; Markham, Brian L.; Biggar, Stuart F.; Zalewski, Edward F.; Spyak, Paul R.; Cooper, John W.;

Sphere-shaped nano-hydroxyapatite/chitosan/gelatin 3D porous scaffolds increase proliferation and osteogenic differentiation of human induced pluripotent stem cells from gingival fibroblasts.

PubMed

Ji, Jun; Tong, Xin; Huang, Xiaofeng; Wang, Tiancong; Lin, Zitong; Cao, Yazhou; Zhang, Junfeng; Dong, Lei; Qin, Haiyan; Hu, Qingang

2015-07-08

Hydroxyapatite (HA) is an important component of human bone and bone tissue engineering scaffolds. A plethora of bone tissue engineering scaffolds have been synthesized so far, including nano-HA/chitosan/gelatin (nHA/CG) scaffolds; and for seeding cells, stem cells, especially induced pluripotent stem cells (iPSCs), have been a promising cell source for bone tissue engineering recently. However, the influence of different HA nano-particle morphologies on the osteogenic differentiation of human iPSCs (hiPSCs) from human gingival fibroblasts (hGFs) is unknown. The purpose of this study was to investigate the osteogenic differentiation of hiPSCs from hGFs seeded on nHA/CG scaffolds with 2 shapes (rod and sphere) of nHA particles. Firstly, hGFs isolated from discarded normal gingival tissues were reprogrammed into hiPSCs. Secondly, hiPSCs were seeded on rod-like nHA/CG (rod-nHA/CG) and sphere-shaped nHA/CG (sphere-nHA/CG) scaffolds respectively and then cell/scaffold complexes were cultured in vitro. Scanning electron microscope, hematoxyline and eosin (HE) staining, Masson's staining, and quantitative real-time polymerase chain reaction techniques were used to examine hiPSC morphology, proliferation, and differentiation on rod-nHA/CG and sphere-nHA/CG scaffolds. Finally, hiPSCs composited with 2 kinds of nHA/CG were transplanted in vivo in a subcutaneous implantation model for 12 weeks; pure scaffolds were also transplanted as a blank control. HE, Masson's, and immunohistochemistry staining were applied to detect new bone regeneration ability. The results showed that sphere-nHA/CG significantly increased hiPSCs from hGF proliferation and osteogenic differentiation in vitro. hiPSCs and sphere-nHA/CG composities generated large bone, whereas hiPSCs and rod-nHA/CG composities produced tiny bone in vivo. Moreover, pure scaffolds without cells almost produced no bone. In conclusion, our work provided a potential innovative bone tissue engineering approach using clinically discarded gingival tissues and sphere-nHA/CG scaffolds.

Measurement of the Casimir Force between Two Spheres

NASA Astrophysics Data System (ADS)

Garrett, Joseph L.; Somers, David A. T.; Munday, Jeremy N.

2018-01-01

Complex interaction geometries offer a unique opportunity to modify the strength and sign of the Casimir force. However, measurements have traditionally been limited to sphere-plate or plate-plate configurations. Prior attempts to extend measurements to different geometries relied on either nanofabrication techniques that are limited to only a few materials or slight modifications of the sphere-plate geometry due to alignment difficulties of more intricate configurations. Here, we overcome this obstacle to present measurements of the Casimir force between two gold spheres using an atomic force microscope. Force measurements are alternated with topographical scans in the x -y plane to maintain alignment of the two spheres to within approximately 400 nm (˜1 % of the sphere radii). Our experimental results are consistent with Lifshitz's theory using the proximity force approximation (PFA), and corrections to the PFA are bounded using nine sphere-sphere and three sphere-plate measurements with spheres of varying radii.

Sensory impacts of food-packaging interactions.

PubMed

Duncan, Susan E; Webster, Janet B

2009-01-01

Sensory changes in food products result from intentional or unintentional interactions with packaging materials and from failure of materials to protect product integrity or quality. Resolving sensory issues related to plastic food packaging involves knowledge provided by sensory scientists, materials scientists, packaging manufacturers, food processors, and consumers. Effective communication among scientists and engineers from different disciplines and industries can help scientists understand package-product interactions. Very limited published literature describes sensory perceptions associated with food-package interactions. This article discusses sensory impacts, with emphasis on oxidation reactions, associated with the interaction of food and materials, including taints, scalping, changes in food quality as a function of packaging, and examples of material innovations for smart packaging that can improve sensory quality of foods and beverages. Sensory evaluation is an important tool for improved package selection and development of new materials.

Self-consistent phonon theory of the crystallization and elasticity of attractive hard spheres.

PubMed

Shin, Homin; Schweizer, Kenneth S

2013-02-28

We propose an Einstein-solid, self-consistent phonon theory for the crystal phase of hard spheres that interact via short-range attractions. The approach is first tested against the known behavior of hard spheres, and then applied to homogeneous particles that interact via short-range square well attractions and the Baxter adhesive hard sphere model. Given the crystal symmetry, packing fraction, and strength and range of attractive interactions, an effective harmonic potential experienced by a particle confined to its Wigner-Seitz cell and corresponding mean square vibrational amplitude are self-consistently calculated. The crystal free energy is then computed and, using separate information about the fluid phase free energy, phase diagrams constructed, including a first-order solid-solid phase transition and its associated critical point. The simple theory qualitatively captures all the many distinctive features of the phase diagram (critical and triple point, crystal-fluid re-entrancy, low-density coexistence curve) as a function of attraction range, and overall is in good semi-quantitative agreement with simulation. Knowledge of the particle localization length allows the crystal shear modulus to be estimated based on elementary ideas. Excellent predictions are obtained for the hard sphere crystal. Expanded and condensed face-centered cubic crystals are found to have qualitatively different elastic responses to varying attraction strength or temperature. As temperature increases, the expanded entropic solid stiffens, while the energy-controlled, fully-bonded dense solid softens.

Viscous constraints on predator:food size ratios in microscale feeding

NASA Astrophysics Data System (ADS)

Jabbarzadeh, Mehdi; Fu, Henry

2014-11-01

Small organisms such as protists or copepods may try to capture food by manipulating food with cilia, limbs, or feeding appendages. At these small scales, viscous flow may complicate the ability of a feeding appendage to closely approach a food particle. As a simplified but tractable model of such feeding approach, we consider the problem of two spheres approaching in a Stokes fluid. The first ``feeding'' sphere, which represents a body part or feeding appendage, is pushed with a constant force towards a force-free ``food'' sphere. When the feeding sphere reaches within a cutoff distance of the food sphere we assume that nonhydrodynamic interactions lead to capture. We examine approach for a range of size ratios between the feeding and food sphere. To investigate the approach efficiency, we examine the time required for the feeding sphere to capture the food sphere, as well as how far the feeding sphere must move before it captures the food sphere. We also examine the effect of varying the cutoff distance for capture. We find that hydrodynamic interactions strongly affect the results when the size of the spheres is comparable. We describe what relative sizes between feeding sphere and food particles may be most effective for food capture.

A ocean bottom vector magnetometer

NASA Astrophysics Data System (ADS)

Wang, Xiaomei; Teng, Yuntian; Wang, Chen; Ma, Jiemei

2017-04-01

The new development instrument with a compact spherical coil system and Overhauser magnetometer for measuring the total strength of the magnetic field and the vectors of strength, Delta inclination - Delta declination, meanwhile we also use a triaxial fluxgate instrument of the traditional instrument for geomagnetic vector filed measurement. The advantages of this method are be calibrated by each other and get good performances with automatic operation, good stability and high resolution. Firstly, a brief description of the instrument measurement principles and the key technologies are given. The instrument used a spherical coil system with 34 coils to product the homogeneous volume inside the coils which is large enough to accommodate the sensor of Overhauser total field sensor; the rest of the footlocker-sized ocean-bottom vector magnetometer consists of equipment to run the sensors and records its data (batteries and a data logger), weight to sink it to the sea floor, a remote-controlled acoustic release and flotation to bring the instrument back to the surface. Finally, the accuracy of the instrument was tested in the Geomagnetic station, and the measurement accuracies of total strength and components were better than 0.2nT and 1nT respectively. The figure 1 shows the development instrument structure. it includes six thick glass spheres which protect the sensor, data logger and batteries from the pressures of the deep sea, meanwhile they also provide recycling positive buoyancy; To cushion the glass, the spheres then go inside yellow plastic "hardhats". The triaxial fluxgate is inside No.1 glass spheres, data logger and batteries are inside No.2 glass spheres, the new vector sensor is inside No.3 glass spheres, acoustic communication unit is inside No.4 glass spheres, No.5 and No.6 glass spheres are empty which only provide recycling positive buoyancy. The figure 2 shows the development instrument Physical photo.

Multipurpose Fiber Injected-micro-spherical LIDAR System

NASA Technical Reports Server (NTRS)

Abdelayem, Hossin; Jamison, Tracee

2005-01-01

A technological revolution is occurring in the field of fiber lasers. Over the past two years, the level of power has increased from approx. 100 watts to nearly 1 kilowatt. We are developing a novel fiber laser system, which is a satellite-based LIDAR transmitter of multi-lines. The system is made of a hollow fiber filled with micro-spheres doped with lasing materials. Each sphere has its inherent optical cavity, which makes the system a cavity free and in the same time, emits multi-laser lines for simultaneous multi-task operations. The system is also rugged, compact, lightweight, and durable. Our earlier studies on micro-spheres doped with different laser dyes demonstrated the emission of extremely fine laser lines of less than 3 A line-width, which are of interest for spectroscopic applications, sensing, imaging, and optical communications. Individual dye-doped micro-spheres demonstrated a lasing resonance peaks phenomenon in their fluorescence spectra of linear and nonlinear features that do not exist in the bulk dye solutions. Each individual micro-sphere acts as a laser system with inherent cavity, where the fluorescence line suffers multiple internal reflections within the micro-sphere and gains enough energy to become a laser line. Such resonance peaks are dependent on the sphere's morphology, size, shape, and its refractive index. These resonance peaks are named structural resonance, whispering modes or whispering gallery modes, creeping waves, circumferential waves, surfaces modes, and virtual modes. All of these names refer to the same phenomenon of morphology dependent resonance (MDR), which has already been described and predicted precisely by electromagnetic theory and Lorentz-Mie theory since 1908. The resonance peaks become more obvious when the particle size approaches and exceeds the wavelength of the laser used and the relative index of the particle is greater than that of the surrounding medium. Additional information is included in the original extended abstract.

High temperature insulation for ceramic matrix composites

DOEpatents

Merrill, Gary B.; Morrison, Jay Alan

2001-01-01

A ceramic composition is provided to insulate ceramic matrix composites under high temperature, high heat flux environments. The composition comprises a plurality of hollow oxide-based spheres of various dimensions, a phosphate binder, and at least one oxide filler powder, whereby the phosphate binder partially fills gaps between the spheres and the filler powders. The spheres are situated in the phosphate binder and the filler powders such that each sphere is in contact with at least one other sphere. The spheres may be any combination of Mullite spheres, Alumina spheres, or stabilized Zirconia spheres. The filler powder may be any combination of Alumina, Mullite, Ceria, or Hafnia. Preferably, the phosphate binder is Aluminum Ortho-Phosphate. A method of manufacturing the ceramic insulating composition and its application to CMC substrates are also provided.

High temperature insulation for ceramic matrix composites

DOEpatents

Merrill, Gary B.; Morrison, Jay Alan

2000-01-01

A ceramic composition is provided to insulate ceramic matrix composites under high temperature, high heat flux environments. The composite comprises a plurality of hollow oxide-based spheres of varios dimentions, a phosphate binder, and at least one oxide filler powder, whereby the phosphate binder partially fills gaps between the spheres and the filler powders. The spheres are situated in the phosphate binder and the filler powders such that each sphere is in contact with at least one other sphere. The spheres may be any combination of Mullite spheres, Alumina spheres, or stabilized Zirconia spheres. The filler powder may be any combination of Alumina, Mullite, Ceria, or Hafnia. Preferably, the phosphate binder is Aluminum Ortho-Phosphate. A method of manufacturing the ceramic insulating composition and its application to CMC substates are also provided.

High temperature insulation for ceramic matrix composites

DOEpatents

Merrill, Gary B.; Morrison, Jay Alan

2004-01-13

A ceramic composition is provided to insulate ceramic matrix composites under high temperature, high heat flux environments. The composition comprises a plurality of hollow oxide-based spheres of various dimensions, a phosphate binder, and at least one oxide filler powder, whereby the phosphate binder partially fills gaps between the spheres and the filler powders. The spheres are situated in the phosphate binder and the filler powders such that each sphere is in contact with at least one other sphere. The spheres may be any combination of Mullite spheres, Alumina spheres, or stabilized Zirconia spheres. The filler powder may be any combination of Alumina, Mullite, Ceria, or Hafnia. Preferably, the phosphate binder is Aluminum Ortho-Phosphate. A method of manufacturing the ceramic insulating composition and its application to CMC substrates are also provided.

Design and tolerance analysis of a transmission sphere by interferometer model

NASA Astrophysics Data System (ADS)

Peng, Wei-Jei; Ho, Cheng-Fong; Lin, Wen-Lung; Yu, Zong-Ru; Huang, Chien-Yao; Hsu, Wei-Yao

2015-09-01

The design of a 6-in, f/2.2 transmission sphere for Fizeau interferometry is presented in this paper. To predict the actual performance during design phase, we build an interferometer model combined with tolerance analysis in Zemax. Evaluating focus imaging is not enough for a double pass optical system. Thus, we study the interferometer model that includes system error, wavefronts reflected from reference surface and tested surface. Firstly, we generate a deformation map of the tested surface. Because of multiple configurations in Zemax, we can get the test wavefront and the reference wavefront reflected from the tested surface and the reference surface of transmission sphere respectively. According to the theory of interferometry, we subtract both wavefronts to acquire the phase of tested surface. Zernike polynomial is applied to transfer the map from phase to sag and to remove piston, tilt and power. The restored map is the same as original map; because of no system error exists. Secondly, perturbed tolerances including fabrication of lenses and assembly are considered. The system error occurs because the test and reference beam are no longer common path perfectly. The restored map is inaccurate while the system error is added. Although the system error can be subtracted by calibration, it should be still controlled within a small range to avoid calibration error. Generally the reference wavefront error including the system error and the irregularity of the reference surface of 6-in transmission sphere is measured within peak-to-valley (PV) 0.1 λ (λ=0.6328 um), which is not easy to approach. Consequently, it is necessary to predict the value of system error before manufacture. Finally, a prototype is developed and tested by a reference surface with PV 0.1 λ irregularity.

Flexible packaging for microelectronic devices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anderson, Benjamin John; Nielson, Gregory N.; Cruz-Campa, Jose Luis

An apparatus, method, and system, the apparatus and system including a flexible microsystems enabled microelectronic device package including a microelectronic device positioned on a substrate; an encapsulation layer encapsulating the microelectronic device and the substrate; a protective layer positioned around the encapsulating layer; and a reinforcing layer coupled to the protective layer, wherein the substrate, encapsulation layer, protective layer and reinforcing layer form a flexible and optically transparent package around the microelectronic device. The method including encapsulating a microelectronic device positioned on a substrate within an encapsulation layer; sealing the encapsulated microelectronic device within a protective layer; and coupling themore » protective layer to a reinforcing layer, wherein the substrate, encapsulation layer, protective layer and reinforcing layer form a flexible and optically transparent package around the microelectronic device.« less

Near-memory data reorganization engine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gokhale, Maya; Lloyd, G. Scott

A memory subsystem package is provided that has processing logic for data reorganization within the memory subsystem package. The processing logic is adapted to reorganize data stored within the memory subsystem package. In some embodiments, the memory subsystem package includes memory units, a memory interconnect, and a data reorganization engine ("DRE"). The data reorganization engine includes a stream interconnect and DRE units including a control processor and a load-store unit. The control processor is adapted to execute instructions to control a data reorganization. The load-store unit is adapted to process data move commands received from the control processor via themore » stream interconnect for loading data from a load memory address of a memory unit and storing data to a store memory address of a memory unit.« less

NASA EEE Parts and NASA Electronic Parts and Packaging (NEPP) Program Update 2018

NASA Technical Reports Server (NTRS)

Label, Kenneth A.; Sampson, Michael J.; Pellish, Jonathan A.; Majewicz, Peter J.

2018-01-01

NASA Electronic Parts and Packaging (NEPP) Program and NASA Electronic Parts Assurance Group (NEPAG) are NASAs point-of-contacts for reliability and radiation tolerance of EEE parts and their packages. This presentation includes an FY18 program overview.

2 CFR 200.512 - Report submission.

Code of Federal Regulations, 2014 CFR

2014-01-01

... the reporting package do not include protected personally identifiable information. (b) Data... packages and the data collection form. All Federal agencies, pass-through entities and others interested in a reporting package and data collection form must obtain it by accessing the FAC. (1) The auditee...

Solutions for the conductivity of multi-coated spheres and spherically symmetric inclusion problems

NASA Astrophysics Data System (ADS)

Pham, Duc Chinh

2018-02-01

Variational results on the macroscopic conductivity (thermal, electrical, etc.) of the multi-coated sphere assemblage have been used to derive the explicit expression of the respective field (thermal, electrical, etc.) within the spheres in d dimensions (d=2,3). A differential substitution approach has been developed to construct various explicit expressions or determining equations for the effective spherically symmetric inclusion problems, which include those with radially variable conductivity, different radially variable transverse and normal conductivities, and those involving imperfect interfaces, in d dimensions. When the volume proportion of the outermost spherical shell increases toward 1, one obtains the respective exact results for the most important specific cases: the dilute solutions for the compound inhomogeneities suspended in a major matrix phase. Those dilute solution results are also needed for other effective medium approximation schemes.

Bubble nucleation and inflationary perturbations

NASA Astrophysics Data System (ADS)

Firouzjahi, Hassan; Jazayeri, Sadra; Karami, Asieh; Rostami, Tahereh

2017-12-01

In this work we study the imprints of bubble nucleation on primordial inflationary perturbations. We assume that the bubble is formed via the tunneling of a spectator field from the false vacuum of its potential to its true vacuum. We consider the configuration in which the observable CMB sphere is initially outside of the bubble. As the bubble expands, more and more regions of the exterior false vacuum, including our CMB sphere, fall into the interior of the bubble. The modes which leave the horizon during inflation at the time when the bubble wall collides with the observable CMB sphere are affected the most. The bubble wall induces non-trivial anisotropic and scale dependent corrections in the two point function of the curvature perturbation. The corrections in the curvature perturbation and the diagonal and off-diagonal elements of CMB power spectrum are estimated.

Experimental validation of absolute SPECT/CT quantification for response monitoring in breast cancer.

PubMed

Collarino, Angela; Pereira Arias-Bouda, Lenka M; Valdés Olmos, Renato A; van der Tol, Pieternel; Dibbets-Schneider, Petra; de Geus-Oei, Lioe-Fee; van Velden, Floris H P

2018-05-01

Recent developments in iterative image reconstruction enable absolute quantification of SPECT/CT studies by incorporating compensation for collimator-detector response, attenuation, and scatter as well as resolution recovery into the reconstruction process (Evolution; Q.Metrix package; GE Healthcare, Little Chalfont, UK). The aim of this experimental study is to assess its quantitative accuracy for potential clinical 99m Tc-sestamibi (MIBI)-related SPECT/CT application in neoadjuvant chemotherapy response studies in breast cancer. Two phantoms were filled with MIBI and acquired on a SPECT/CT gamma camera (Discovery 670 Pro; GE Healthcare), that is, a water cylinder and a NEMA body phantom containing six spheres that were filled with an activity concentration reflecting clinical MIBI uptake. Subsequently, volumes-of-interest (VOI) of each sphere were drawn (semi)automatically on SPECT using various isocontour methods or manually on CT. Finally, prone MIBI SPECT/CT scans were acquired 5 and 90 min p.i. in a locally advanced breast cancer patient. Activity concentration in the four largest spheres converged after nine iterations of evolution. Depending on the count statistics, the accuracy of the reconstructed activity concentration varied between -4.7 and -0.16% (VOI covering the entire phantom) and from 6.9% to 10% (8.8 cm ⌀ cylinder VOI placed in the center of the phantom). Recovery coefficients of SUV max were 1.89 ± 0.18, 1.76 ± 0.17, 2.00 ± 0.38, 1.89 ± 0.35, and 0.90 ± 0.26 for spheres with 37, 28, 22, 17, and 13 mm ⌀, respectively. Recovery coefficients of SUV mean were 1.07 ± 0.06, 1.03 ± 0.09, 1.17 ± 0.21, 1.10 ± 0.20, and 0.52 ± 0.14 (42% isocontour); 1.10 ± 0.07, 1.02 ± 0.09, 1.13 ± 0.19, 1.06 ± 0.19, and 0.51 ± 0.13 (36% isocontour with local background correction); and 0.96, 1.09, 1.03, 1.03, and 0.29 (CT). Patient study results were concordant with the phantom validation. Absolute SPECT/CT quantification of breast studies using MIBI seems feasible (<17% deviation) when a 42% isocontour is used for delineation for tumors of at least 17 mm diameter. However, with tumor shrinkage, response evaluation should be handled with caution, especially when using SUV max . © 2018 American Association of Physicists in Medicine.

Electromagnetic Energy Localization and Characterization of Composites

DTIC Science & Technology

2013-01-01

polyhedrons ), and [39] (spheres and a complex yet symmetric structure). With time-domain EM analysis, regular shapes, such as cubes, spheres, and regular...spheres), [40] (spheres, crosses, cylinders, and polyhedrons ), and [41] (spheres and cylinders); and 3-D random mixtures using a frequency-domain finite...element method [42] ( polyhedrons ), and [43], [44] (spheres). Such steady-state analyses are limited as they, for example, do not capture temporal

Movements of a Sphere Moving Over Smooth and Rough Inclines

NASA Astrophysics Data System (ADS)

Jan, Chyan-Deng

1992-01-01

The steady movements of a sphere over a rough incline in air, and over smooth and rough inclines in a liquid were studied theoretically and experimentally. The principle of energy conservation was used to analyze the translation velocities, rolling resistances, and drag coefficients of a sphere moving over the inclines. The rolling resistance to the movement of a sphere from the rough incline was presumed to be caused by collisions and frictional slidings. A varnished wooden board was placed on the bottom of an experimental tilting flume to form a smooth incline and a layer of spheres identical to the sphere moving over them was placed on the smooth wooden board to form a rough incline. Spheres used in the experiments were glass spheres, steel spheres, and golf balls. Experiments show that a sphere moving over a rough incline with negligible fluid drag in air can reach a constant translation velocity. This constant velocity was found to be proportional to the bed inclination (between 11 ^circ and 21^circ) and the square root of the sphere's diameter, but seemingly independent of the sphere's specific gravity. Two empirical coefficients in the theoretical expression of the sphere's translation velocity were determined by experiments. The collision and friction parts of the shear stress exerted on the interface between the moving sphere and rough incline were determined. The ratio of collision to friction parts appears to increase with increase in the bed inclination. These two parts seem to be of the same order of magnitude. The rolling resistances and the relations between the drag coefficient and Reynolds number for a sphere moving over smooth and rough inclines in a liquid, such as water or salad oil, were determined by a regression analysis based on experimental data. It was found that the drag coefficient for a sphere over the rough incline is larger than that for a sphere over the smooth incline, and both of which are much larger than that for a sphere in free fall. The relative magnitudes of the shear stresses due to drag, collision, and friction were also determined in terms of the Reynolds number.

Phase diagram of heteronuclear Janus dumbbells

NASA Astrophysics Data System (ADS)

O'Toole, Patrick; Giacometti, Achille; Hudson, Toby

Using Aggregation-Volume-Bias Monte Carlo simulations along with Successive Umbrella Sampling and Histogram Re-weighting, we study the phase diagram of a system of dumbbells formed by two touching spheres having variable sizes, as well as different interaction properties. The first sphere ($h$) interacts with all other spheres belonging to different dumbbells with a hard-sphere potential. The second sphere ($s$) interacts via a square-well interaction with other $s$ spheres belonging to different dumbbells and with a hard-sphere potential with all remaining $h$ spheres. We focus on the region where the $s$ sphere is larger than the $h$ sphere, as measured by a parameter $1\\le \\alpha\\le 2 $ controlling the relative size of the two spheres. As $\\alpha \\to 2$ a simple fluid of square-well spheres is recovered, whereas $\\alpha \\to 1$ corresponds to the Janus dumbbell limit, where the $h$ and $s$ spheres have equal sizes. Many phase diagrams falling into three classes are observed, depending on the value of $\\alpha$. The $1.8 \\le \\alpha \\le 2$ is dominated by a gas-liquid phase separation very similar to that of a pure square-well fluid with varied critical temperature and density. When $1.3 \\le \\alpha \\le 1.8$ we find a progressive destabilization of the gas-liquid phase diagram by the onset of self-assembled structures, that eventually lead to a metastability of the gas-liquid transition below $\\alpha=1.2$.

Quality and safety aspects of meat products as affected by various physical manipulations of packaging materials.

PubMed

Lee, Keun Taik

2010-09-01

This article explores the effects of physically manipulated packaging materials on the quality and safety of meat products. Recently, innovative measures for improving quality and extending the shelf-life of packaged meat products have been developed, utilizing technologies including barrier film, active packaging, nanotechnology, microperforation, irradiation, plasma and far-infrared ray (FIR) treatments. Despite these developments, each technology has peculiar drawbacks which will need to be addressed by meat scientists in the future. To develop successful meat packaging systems, key product characteristics affecting stability, environmental conditions during storage until consumption, and consumers' packaging expectations must all be taken into consideration. Furthermore, the safety issues related to packaging materials must also be taken into account when processing, packaging and storing meat products.

Packaging films for electronic and space-related hardware

NASA Astrophysics Data System (ADS)

Shon, E. M.; Hamberg, O.

1985-08-01

Flexible packaging films are used to bag and/or wrap precision cleaned electronic or space hardware to protect them from environmental degradation during shipping and storage. Selection of packaging films depends on a knowledge of product requirements and packaging film characteristics. The literature presently available on protective packaging films has been updated to include new materials and to amplify space-related applications. Presently available packaging film materials are compared for their various characteristics: electrostatic discharge (ESD) control, flame retardancy, water vapor transmission rate, particulate shedding, molecular contamination, and transparency. The tradeoff between product requirements and the characteristics of the packaging films available are discussed. Selection considerations are given for the application of specific materials of space hardware-related applications. Applications for intimate, environmental, and electrostatic protective packaging are discussed.

Pediatric PRK (PhotoRefractive Keratectomy) with Mitomycin C (MCC) for Persistent Anisometropic Amblyopia. A Case Report.

PubMed

Crawford, Courtney M; Frazier, Travis C; Torres, Mark F; Arnold, Robert W; Mazzoli, Robert A; Raymond, William R

2012-01-01

To evaluate the safety and efficacy of photorefractive keratectomy (PRK) with Mitomycin C (MMC) for the treatment of severe pediatric anisometropia and amblyopia resistant to more conservative treatment modalities. A 3 year-old-child, who at 18 months old underwent unilateral diode laser treatment for threshold ROP, developed 11 diopters of anisometropic myopia and secondary dense amblyopia of the Right Eye. Only after all conservative treatment options failed was he treated with PRK and MMC. Principal outcome measures included cycloplegic refraction, the amount of refractive correction, degree of corneal haze and change in visual acuity. On presentation: BCVA: 20/CF OD; 20/30 OS. CRNS: -11.50 diopters sphere OD; -0.50 diopters sphere OS. Unilateral PRK followed by application of MMC (0.2 mg/ml) for 1 min was performed under general anesthesia. Three-month postoperative findings include: VA: 20/30 OD; 20/25 OS. CRNS: +0.25 diopters sphere OD. At one year, the BCVA remained equal at the 20/30 level despite mild myopic regression OD. CRNS OD at one year was -1.25 +050 x 116. No corneal haze was appreciated. In this child, treatment with PRK and MMC safely reduced the anisometropia thus facilitating his visual rehabilitation. While encouraging, further study is required to verify the longer term results of this single case. To evaluate the safety and efficacy of photorefractive keratectomy (PRK) with Mitomycin C (MMC) for the treatment of severe pediatric anisometropia and amblyopia resistant to more conservative treatment modalities. A 3 year-old-child, who at 18 months old underwent unilateral diode laser treatment for threshold ROP, developed 11 diopters of anisometropic myopia and secondary dense amblyopia of the Right Eye. Only after all conservative treatment options failed was he treated with PRK and MMC. Principal outcome measures included cycloplegic refraction, the amount of refractive correction, degree of corneal haze and change in visual acuity. On presentation: BCVA: 20/CF OD; 20/30 OS. CRNS: -11.50 diopters sphere OD; -0.50 diopters sphere OS. Unilateral PRK followed by application of MMC (0.2 mg/ml) for 1 min was performed under general anesthesia. Three-month postoperative findings include: VA: 20/30 OD; 20/25 OS. CRNS: +0.25 diopters sphere OD. At one year, the BCVA remained equal at the 20/30 level despite mild myopic regression OD. CRNS OD at one year was -1.25 +050 x 116. No corneal haze was appreciated. In this child, treatment with PRK and MMC safely reduced the anisometropia thus facilitating his visual rehabilitation. While encouraging, further study is required to verify the longer term results of this single case.

Current topics in active and intelligent food packaging for preservation of fresh foods.

PubMed

Lee, Seung Yuan; Lee, Seung Jae; Choi, Dong Soo; Hur, Sun Jin

2015-11-01

The purpose of this review is to provide an overview of current packaging systems, e.g. active packaging and intelligent packaging, for various foods. Active packaging, such as modified atmosphere packaging (MAP), extends the shelf life of fresh produce, provides a high-quality product, reduces economic losses, including those caused by delay of ripening, and improves appearance. However, in active packaging, several variables must be considered, such as temperature control and different gas formulations with different product types and microorganisms. Active packaging refers to the incorporation of additive agents into packaging materials with the purpose of maintaining or extending food product quality and shelf life. Intelligent packaging is emerging as a potential advantage in food processing and is an especially useful tool for tracking product information and monitoring product conditions. Moreover, intelligent packaging facilitates data access and information exchange by altering conditions inside or outside the packaging and product. In spite of these advantages, few of these packaging systems are commercialized because of high cost, strict safety and hygiene regulations or limited consumer acceptance. Therefore more research is needed to develop cheaper, more easily applicable and effective packaging systems for various foods. © 2015 Society of Chemical Industry.

Terminal energy distribution of blast waves from bursting spheres

NASA Technical Reports Server (NTRS)

Adamczyk, A. A.; Strehlow, R. A.

1977-01-01

The calculation results for the total energy delivered to the surroundings by the burst of an idealized massless sphere containing an ideal gas are presented. The logic development of various formulas for sphere energy is also presented. For all types of sphere bursts the fraction of the total initial energy available in the sphere that is delivered to the surroundings is shown to lie between that delivered for the constant pressure addition of energy to a source region and that delivered by isentropic expansion of the sphere. The relative value of E sub/Q increases at fixed sphere pressure/surrounding pressure as sphere temperature increases because the velocity of sound increases.

21 CFR 177.1320 - Ethylene-ethyl acrylate copolymers.

Code of Federal Regulations, 2011 CFR

2011-04-01

..., packaging, transporting, or holding food, in accordance with the following prescribed conditions: (a... substances may include: (1) Substances generally recognized as safe in food and food packaging. (2... food except as a component of articles used for packaging or holding food during cooking provided they...

Large space telescope, phase A. Volume 4: Scientific instrument package

NASA Technical Reports Server (NTRS)

1972-01-01

The design and characteristics of the scientific instrument package for the Large Space Telescope are discussed. The subjects include: (1) general scientific objectives, (2) package system analysis, (3) scientific instrumentation, (4) imaging photoelectric sensors, (5) environmental considerations, and (6) reliability and maintainability.

Introduction to Software Packages. [Final Report.

ERIC Educational Resources Information Center

Frankel, Sheila, Ed.; And Others

This document provides an introduction to applications computer software packages that support functional managers in government and encourages the use of such packages as an alternative to in-house development. A review of current application areas includes budget/project management, financial management/accounting, payroll, personnel,…

10 CFR 71.71 - Normal conditions of transport.

Code of Federal Regulations, 2014 CFR

2014-01-01

... NUCLEAR REGULATORY COMMISSION (CONTINUED) PACKAGING AND TRANSPORTATION OF RADIOACTIVE MATERIAL Package... each package design under normal conditions of transport must include a determination of the effect on... following table: Insolation Data Form and location of surface Total insolation for a 12-hour period(g cal...

10 CFR 71.71 - Normal conditions of transport.

Code of Federal Regulations, 2012 CFR

2012-01-01

... NUCLEAR REGULATORY COMMISSION (CONTINUED) PACKAGING AND TRANSPORTATION OF RADIOACTIVE MATERIAL Package... each package design under normal conditions of transport must include a determination of the effect on... following table: Insolation Data Form and location of surface Total insolation for a 12-hour period(g cal...

10 CFR 71.71 - Normal conditions of transport.

Code of Federal Regulations, 2011 CFR

2011-01-01

... NUCLEAR REGULATORY COMMISSION (CONTINUED) PACKAGING AND TRANSPORTATION OF RADIOACTIVE MATERIAL Package... each package design under normal conditions of transport must include a determination of the effect on... following table: Insolation Data Form and location of surface Total insolation for a 12-hour period(g cal...

10 CFR 71.71 - Normal conditions of transport.

Code of Federal Regulations, 2010 CFR

2010-01-01

... NUCLEAR REGULATORY COMMISSION (CONTINUED) PACKAGING AND TRANSPORTATION OF RADIOACTIVE MATERIAL Package... each package design under normal conditions of transport must include a determination of the effect on... following table: Insolation Data Form and location of surface Total insolation for a 12-hour period(g cal...

10 CFR 71.71 - Normal conditions of transport.

Code of Federal Regulations, 2013 CFR

2013-01-01

... NUCLEAR REGULATORY COMMISSION (CONTINUED) PACKAGING AND TRANSPORTATION OF RADIOACTIVE MATERIAL Package... each package design under normal conditions of transport must include a determination of the effect on... following table: Insolation Data Form and location of surface Total insolation for a 12-hour period(g cal...

AIN-Based Packaging for SiC High-Temperature Electronics

NASA Technical Reports Server (NTRS)

Savrun, Ender

2004-01-01

Packaging made primarily of aluminum nitride has been developed to enclose silicon carbide-based integrated circuits (ICs), including circuits containing SiC-based power diodes, that are capable of operation under conditions more severe than can be withstood by silicon-based integrated circuits. A major objective of this development was to enable packaged SiC electronic circuits to operate continuously at temperatures up to 500 C. AlN-packaged SiC electronic circuits have commercial potential for incorporation into high-power electronic equipment and into sensors that must withstand high temperatures and/or high pressures in diverse applications that include exploration in outer space, well logging, and monitoring of nuclear power systems. This packaging embodies concepts drawn from flip-chip packaging of silicon-based integrated circuits. One or more SiC-based circuit chips are mounted on an aluminum nitride package substrate or sandwiched between two such substrates. Intimate electrical connections between metal conductors on the chip(s) and the metal conductors on external circuits are made by direct bonding to interconnections on the package substrate(s) and/or by use of holes through the package substrate(s). This approach eliminates the need for wire bonds, which have been the most vulnerable links in conventional electronic circuitry in hostile environments. Moreover, the elimination of wire bonds makes it possible to pack chips more densely than was previously possible.

Inclusion of Specialist and Generalist Stimuli in Attract-and-Kill Programs: Their Relative Efficacy in Apple Maggot Fly (Diptera: Tephritidae) Pest Management.

PubMed

Morrison, William R; Lee, Doo-Hyung; Reissig, W Harvey; Combs, David; Leahy, Kathleen; Tuttle, Arthur; Cooley, Daniel; Leskey, Tracy C

2016-08-01

Investigating the chemical ecology of agricultural systems continues to be a salient part of integrated pest management programs. Apple maggot fly, a key pest of apple in eastern North America, is a visual specialist with attraction to host fruit-mimicking cues. These cues have been incorporated into red spherical traps used for both monitoring and behaviorally based management. Incorporating generalist or specialist olfactory cues can potentially increase the overall success of this management system. The primary aim of this study was to evaluate the attractiveness of a generalist olfactory cue, ammonium carbonate, and the specialist olfactory cue, a five-component apple volatile blend, when included as a component of a red attracticidal sphere system. Secondly, we assessed how critical it was to maintain minimal deviation from the optimal, full-round specialist visual stimulus provided by red spheres. Finally, attracticidal spheres were deployed with specialist olfactory cues in commercial apple orchards to evaluate their potential for effective management of apple maggot. Ammonium carbonate did not increase residency, feeding time, or mortality in the laboratory-based trials. Field deployment of specialist olfactory cues increased apple maggot captures on red spheres, while the generalist cue did not. Apple maggot tolerated some deviation from the optimal visual stimulus without reducing captures on red spheres. Attracticidal spheres hung in perimeter trees in orchards resulted in acceptable and statistically identical levels of control compared with standard insecticide programs used by growers. Overall, our study contributes valuable information for developing a reliable attract-and-kill system for apple maggot. Published by Oxford University Press on behalf of Entomological Society of America 2016. This work is written by US Government employees and is in the public domain in the United States.

Comparison of cycloplegic refraction between Grand Seiko autorefractor and Retinomax autorefractor in the Vision in Preschoolers–Hyperopia in Preschoolers (VIP-HIP) Study

PubMed Central

Ying, Gui-shuang; Maguire, Maureen G.; Kulp, Marjean Taylor; Ciner, Elise; Moore, Bruce; Pistilli, Maxwell; Candy, Rowan

2017-01-01

PURPOSE To evaluate the agreement of cycloplegic refractive error measures between the Grand Seiko and Retinomax autorefractors in 4- and 5-year-old children. METHODS Cycloplegic refractive error of children was measured using the Grand Seiko and Retinomax during a comprehensive eye examination. Accommodative error was measured using the Grand Seiko. The differences in sphere, cylinder, spherical equivalent (SE) and intereye vector dioptric distance (VDD) between autorefractors were assessed using the Bland-Altman plot and 95% limits of agreement (95% LoA). RESULTS A total of 702 examinations were included. Compared to the Retinomax, the Grand Seiko provided statistically significantly larger values of sphere (mean difference, 0.34 D; 95% LoA, −0.46 to 1.14 D), SE (mean, 0.25 D; 95% LoA, −0.55 to 1.05 D), VDD (mean, 0.19 D; 95% LoA, −0.67 to 1.05 D), and more cylinder (mean, −0.18 D; 95% LoA, −0.91 to 0.55 D). The Grand Seiko measured ≥0.5 D than Retinomax in 43.1% of eyes for sphere and 29.8% of eyes for SE. In multivariate analysis, eyes with SE of >4 D (based on the average of two autorefractors) had larger differences in sphere (mean, 0.66 D vs 0.35 D; P < 0.0001) and SE (0.57 D vs 0.26 D; P < 0.0001) than eyes with SE of ≤4 D. CONCLUSIONS Under cycloplegia, the Grand Seiko provided higher measures of sphere, more cylinder, and higher SE than the Retinomax. Higher refractive error was associated with larger differences in sphere and SE between the Grand Seiko and Retinomax. (J AAPOS 2017;21: 219–223) PMID:28528993

Savannah River Site Eastern Transportation Hub: A Concept For a DOE Eastern Packaging, Staging and Maintenance Center - 13143

DOE Office of Scientific and Technical Information (OSTI.GOV)

England, Jeffery L.; Adams, Karen; Maxted, Maxcine

2013-07-01

The Department of Energy (DOE) is working to de-inventory sites and consolidate hazardous materials for processing and disposal. The DOE administers a wide range of certified shipping packages for the transport of hazardous materials to include Special Nuclear Material (SNM), radioactive materials, sealed sources and radioactive wastes. A critical element to successful and safe transportation of these materials is the availability of certified shipping packages. There are over seven thousand certified packagings (i.e., Type B/Type AF) utilized within the DOE for current missions. The synergistic effects of consolidated maintenance, refurbishment, testing, certification, and costing of these services would allow formore » efficient management of the packagings inventory and to support anticipated future in-commerce shipping needs. The Savannah River Site (SRS) receives and ships radioactive materials (including SNM) and waste on a regular basis for critical missions such as consolidated storage, stabilization, purification, or disposition using H-Canyon and HB-Line. The Savannah River National Laboratory (SRNL) has the technical capability and equipment for all aspects of packaging management. SRS has the only active material processing facility in the DOE complex and is one of the sites of choice for nuclear material consolidation. SRS is a logical location to perform maintenance and periodic testing of the DOE fleet of certified packagings. This initiative envisions a DOE Eastern Packaging Staging and Maintenance Center (PSMC) at the SRS and a western hub at the Nevada National Security Site (NNSS), an active DOE Regional Disposal Site. The PSMC's would be the first place DOE would go to meet their radioactive packaging needs and the primary locations projects would go to disposition excess packaging for beneficial reuse. These two hubs would provide the centralized management of a packaging fleet rather than the current approach to design, procure, maintain and dispose of packagings on a project-by-project basis. This initiative provides significant savings in packaging costs and acceleration of project schedules. In addition to certified packaging, the PSMC would be well suited for select designs of 7A Type A packaging and Industrial Packaging. (authors)« less

JetWeb: A WWW interface and database for Monte Carlo tuning and validation

NASA Astrophysics Data System (ADS)

Butterworth, J. M.; Butterworth, S.

2003-06-01

A World Wide Web interface to a Monte Carlo tuning facility is described. The aim of the package is to allow rapid and reproducible comparisons to be made between detailed measurements at high-energy physics colliders and general physics simulation packages. The package includes a relational database, a Java servlet query and display facility, and clean interfaces to simulation packages and their parameters.

MODFLOW-NWT, A Newton formulation for MODFLOW-2005

USGS Publications Warehouse

Niswonger, Richard G.; Panday, Sorab; Ibaraki, Motomu

2011-01-01

This report documents a Newton formulation of MODFLOW-2005, called MODFLOW-NWT. MODFLOW-NWT is a standalone program that is intended for solving problems involving drying and rewetting nonlinearities of the unconfined groundwater-flow equation. MODFLOW-NWT must be used with the Upstream-Weighting (UPW) Package for calculating intercell conductances in a different manner than is done in the Block-Centered Flow (BCF), Layer Property Flow (LPF), or Hydrogeologic-Unit Flow (HUF; Anderman and Hill, 2000) Packages. The UPW Package treats nonlinearities of cell drying and rewetting by use of a continuous function of groundwater head, rather than the discrete approach of drying and rewetting that is used by the BCF, LPF, and HUF Packages. This further enables application of the Newton formulation for unconfined groundwater-flow problems because conductance derivatives required by the Newton method are smooth over the full range of head for a model cell. The NWT linearization approach generates an asymmetric matrix, which is different from the standard MODFLOW formulation that generates a symmetric matrix. Because all linear solvers presently available for use with MODFLOW-2005 solve only symmetric matrices, MODFLOW-NWT includes two previously developed asymmetric matrix-solver options. The matrix-solver options include a generalized-minimum-residual (GMRES) Solver and an Orthomin / stabilized conjugate-gradient (CGSTAB) Solver. The GMRES Solver is documented in a previously published report, such that only a brief description and input instructions are provided in this report. However, the CGSTAB Solver (called XMD) is documented in this report. Flow-property input for the UPW Package is designed based on the LPF Package and material-property input is identical to that for the LPF Package except that the rewetting and vertical-conductance correction options of the LPF Package are not available with the UPW Package. Input files constructed for the LPF Package can be used with slight modification as input for the UPW Package. This report presents the theory and methods used by MODFLOW-NWT, including the UPW Package. Additionally, this report provides comparisons of the new methodology to analytical solutions of groundwater flow and to standard MODFLOW-2005 results by use of an unconfined aquifer MODFLOW example problem. The standard MODFLOW-2005 simulation uses the LPF Package with the wet/dry option active. A new example problem also is presented to demonstrate MODFLOW-NWT's ability to provide a solution for a difficult unconfined groundwater-flow problem.

Maldives. Package on population education for special interest groups developed.

PubMed

1995-01-01

The Population Education Program of the Non-Formal Education Center has developed a package of Population Education for Special Interest Groups comprising a learning package and fieldworker's guide. The learning package is especially developed for teaching population education for out-of-school populations. Special interest groups in Maldives include newly married couples, adolescents, and working youth. Produced under the guidance of UNESCO, Bangkok, the package contains 36 different materials such as posters, charts, leaflets, booklets, stories, and illustrated booklets which may be taught in 36 to 45 periods. The materials deal with eight themes, namely, family size and family welfare, population and resources, delayed marriage and parenthood, responsible parenthood, population-related values and beliefs, women in development, AIDS/STD, and respect for old people. Accompanying the learning package is the fieldworker's guide used to teach the package. It contains individual guides for each of the 36 learning materials. The guide gives the titles of the materials, format, objectives of the materials, messages, target groups, and an overview of the content of each learning materials. The methodologies used for teaching the learning materials include role playing, group discussion, questioning, brainstorming, survey, creative writing, problem-solving and evaluation. The package will be used by fieldworkers to conduct island-based population education courses. full text

An examination of product packaging marketing strategies used to promote pediatric multivitamins.

PubMed

Ethan, Danna; Basch, Corey H; Samuel, Lalitha; Quinn, Christine; Dunne, Stephanie

2015-06-01

The purpose of this study was to describe the nature of marketing strategies for multivitamin and multimineral (MVM) supplement packaging and to assess the extent to which these supplements are marketed as food products. A cross-sectional study of children's supplement packaging was conducted. Descriptive statistics identified common marketing practices. Websites of the three largest retail chain pharmacies in the United States and MVM manufacturers were accessed. The study's sample consisted of packaging for 52 children's MVM supplements. Child-targeted marketing included reference to trademarked characters on 42.3% of MVM packaging (n = 22). More than 80% of the sample (n = 42) listed fruity flavors and almost all packaging included descriptive words related to the MVMs' shape and/or flavor (88.5%, n = 46). Nearly one-fifth of the packaging (n = 10) pictured a food item. With respect to parent-targeted promotional language, almost 83% of the supplement packages (n = 43) included text on the support of bodily structure/function. More than half of the sample (53.8%, n = 28) had promotional language related to dietary practice (e.g. organic, gluten-free). Pediatricians can play a role in ensuring that parents are aware of (1) possible risks associated with MVM overconsumption, and (2) the importance of deriving vitamins and minerals from a balanced diet. Given the high number of exposures to pediatric MVMs among youth and established influence of food marketing on shaping children's perceptions and behaviors, further research is necessary to determine the extent to which children's MVMs are marketed as a food product and perceived as such by children.

Template method synthesis of mesoporous carbon spheres and its applications as supercapacitors.

PubMed

Wilgosz, Karolina; Chen, Xuecheng; Kierzek, Krzysztof; Machnikowski, Jacek; Kalenczuk, Ryszard J; Mijowska, Ewa

2012-05-29

Mesoporous carbon spheres (MCS) have been fabricated from structured mesoporous silica sphere using chemical vapor deposition (CVD) with ethylene as a carbon feedstock. The mesoporous carbon spheres have a high specific surface area of 666.8 m2/g and good electrochemical properties. The mechanism of formation mesoporous carbon spheres (carbon spheres) is investigated. The important thing is a surfactant hexadecyl trimethyl ammonium bromide (CTAB), which accelerates the process of carbon deposition. An additional advantage of this surfactant is an increase the yield of product. These mesoporous carbon spheres, which have good electrochemical properties is suitable for supercapacitors.

Template method synthesis of mesoporous carbon spheres and its applications as supercapacitors

NASA Astrophysics Data System (ADS)

Wilgosz, Karolina; Chen, Xuecheng; Kierzek, Krzysztof; Machnikowski, Jacek; Kalenczuk, Ryszard J.; Mijowska, Ewa

2012-05-01

Mesoporous carbon spheres (MCS) have been fabricated from structured mesoporous silica sphere using chemical vapor deposition (CVD) with ethylene as a carbon feedstock. The mesoporous carbon spheres have a high specific surface area of 666.8 m2/g and good electrochemical properties. The mechanism of formation mesoporous carbon spheres (carbon spheres) is investigated. The important thing is a surfactant hexadecyl trimethyl ammonium bromide (CTAB), which accelerates the process of carbon deposition. An additional advantage of this surfactant is an increase the yield of product. These mesoporous carbon spheres, which have good electrochemical properties is suitable for supercapacitors.

Anti-gravity device

NASA Technical Reports Server (NTRS)

Palsingh, S. (Inventor)

1975-01-01

An educational toy useful in demonstrating fundamental concepts regarding the laws of gravity is described. The device comprises a sphere 10 of radius r resting on top of sphere 12 of radius R. The center of gravity of sphere 10 is displaced from its geometrical center by distance D. The dimensions are so related that D((R+r)/r) is greater than r. With the center of gravity of sphere 10 lying on a vertical line, the device is in equilibrium. When sphere 10 is rolled on the surface of sphere 12 it will return to its equilibrium position upon release. This creates an illusion that sphere 10 is defying the laws of gravity. In reality, due to the above noted relationship of D, R, and r, the center of gravity of sphere 10 rises from its equilibrium position as it rolls a short distance up or down the surface of sphere 12.

42 CFR 419.2 - Basis of payment.

Code of Federal Regulations, 2014 CFR

2014-10-01

... part. (b) Determination of hospital outpatient prospective payment rates: Packaged costs. The..., that includes operating and capital-related costs that are integral, ancillary, supportive, dependent..., these packaged costs may include, but are not limited to, the following items and services, the payment...

49 CFR 178.980 - Stacking test.

Code of Federal Regulations, 2013 CFR

2013-10-01

... for transportation and no loss of contents. (2) For fiberboard or wooden Large Packagings, there may be no loss of contents and no permanent deformation that renders the whole Large Packaging, including... deterioration which renders the Large Packaging unsafe for transportation and no loss of contents. (4) For the...

49 CFR 178.980 - Stacking test.

Code of Federal Regulations, 2014 CFR

2014-10-01

... for transportation and no loss of contents. (2) For fiberboard or wooden Large Packagings, there may be no loss of contents and no permanent deformation that renders the whole Large Packaging, including... deterioration which renders the Large Packaging unsafe for transportation and no loss of contents. (4) For the...

78 FR 59347 - Pesticides; Revised Fee Schedule for Registration Applications

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-26

... active ingredients previously combined in other registered products; requires review of data package... data package within RD only; includes data and/or waivers of data for only: product chemistry and/or... source of active ingredient; submission of completely new generic data package; registered uses only...

Open-source Software for Exoplanet Atmospheric Modeling

NASA Astrophysics Data System (ADS)

Cubillos, Patricio; Blecic, Jasmina; Harrington, Joseph

2018-01-01

I will present a suite of self-standing open-source tools to model and retrieve exoplanet spectra implemented for Python. These include: (1) a Bayesian-statistical package to run Levenberg-Marquardt optimization and Markov-chain Monte Carlo posterior sampling, (2) a package to compress line-transition data from HITRAN or Exomol without loss of information, (3) a package to compute partition functions for HITRAN molecules, (4) a package to compute collision-induced absorption, and (5) a package to produce radiative-transfer spectra of transit and eclipse exoplanet observations and atmospheric retrievals.

Packaging of silicon photonic devices: from prototypes to production

NASA Astrophysics Data System (ADS)

Morrissey, Padraic E.; Gradkowski, Kamil; Carroll, Lee; O'Brien, Peter

2018-02-01

The challenges associated with the photonic packaging of silicon devices is often underestimated and remains technically challenging. In this paper, we review some key enabling technologies that will allow us to overcome the current bottleneck in silicon photonic packaging; while also describing the recent developments in standardisation, including the establishment of PIXAPP as the worlds first open-access PIC packaging and assembly Pilot Line. These developments will allow the community to move from low volume prototype photonic packaged devices to large scale volume manufacturing, where the full commercialisation of PIC technology can be realised.

[On the topical aspects of the activity of the Federal Service for Legal and Organizational Providence of the Activity in the Sphere of Sanitary and Epidemiological Providence and Consumer Rights].

PubMed

Onshchenko, G G

2007-01-01

The reorganization of the Federal Service on the Control Over the Sphere of Consumer Rights and Human Welfare has made it possible to significantly increase the number of specialists working in the sphere of consumer rights. In 2005, Federal Service on the Control Over the Sphere of Consumer Rights and its territorial organs carried out 155000 inspections of the legislation on consumer rights; more than 55% of them were off-schedule inspections of economic subjects. The inspections revealed almost 210000 facts of failure of the subjects to follow the rules of consumer legislation (140 reports on infringements). Of all the infringements, 40% were failures to satisfy consumer's rights for information. The Federal Service has opened a hotline on the actual problems of consumer rights. Similar hotlines have been opened by Magadan and Saint Petersburg etc. territory administrations. Among the main tasks directed to perfection of governmental control over consumer rights protection is development of a complex of measures aimed at prevention of infringements in this area, especially in dwelling sphere, medical aid, transportation, retail etc. Also needed are development and realization of interaction between territory organs of the Federal Service and local offices as well as public and remedial organizations working in the field of consumer rights and human welfare. Problems of hygiene and epidemiology in the Federal Service are nowadays being solved by 28 epidemiological, hygienic, and antiplague research institutes employing 3000 researchers including 290 doctors of science and 820 candidates of science. Territory administrations present the main regional structure of the Federal Service. This should be taken into account when building relations between territory administrations and regional offices of the Federal Service. The main directions of the activity of the Federal Service in 2006 are determined by 15 December 2005 order #794 and include a vast list.

Blurring personal health and public priorities: an analysis of celebrity health narratives in the public sphere.

PubMed

Beck, Christina S; Aubuchon, Stellina M; McKenna, Timothy P; Ruhl, Stephanie; Simmons, Nathaniel

2014-01-01

This article explores the functions of personal celebrity health narratives in the public sphere. This study examines data about 157 celebrities, including athletes, actors, musicians, and politicians, who have shared private information regarding a personal health situation (or that of a loved one) with others in the public domain. Part of a larger project on celebrity health narratives, this article highlights three key functions that celebrity health narratives perform--education, inspiration, and activism--and discusses the implications for celebrities and for public conversations about health-related issues.

Intercomparison of Laboratory Radiance Calibration Standards

NASA Technical Reports Server (NTRS)

Pavri, Betina; Chrien, Tom; Green, Robert; Williams, Orlesa

2000-01-01

Several standards for radiometric calibration were measured repeatedly with a spectroradiometer in order to understand how they compared in accuracy and stability. The tested radiance standards included a NIST 1000 W bulb and halon panel, two calibrated and stabilized integrating spheres, and a cavity blackbody. Results indicate good agreement between the blackbody and 1000 W bulb/spectralon panel, If these two radiance sources are assumed correct, then the integrating spheres did not conform. to their manufacturer-reported radiances in several regions of the spectrum. More detailed measurements am underway to investigate the discrepancy.

Interaction of gases with ablative composites. II - Water

NASA Technical Reports Server (NTRS)

Honeycutt, R. H., III; Wightman, J. P.

1974-01-01

An investigation was conducted to study the sorption of water on two ablative composites and their components as a function of pressure and temperature. A pressure range from 0.001 to 10 torr and a temperature range from 25 to 35 C were considered in the investigation. It was found that the sorption of water vapor by the ablative composites and their components varied directly with pressure. The components of the ablative composites included phenolic spheres, cork, a carbon-glass fiber mixture, glass spheres, silica fibers, and a silicone elastomer.

Subwavelength coatings and methods for making and using same

DOEpatents

Alvine, Kyle J.; Bernacki, Bruce E.

2017-02-28

Methods are disclosed for forming subwavelength coatings for use in the UV, visible, or infrared part of the electromagnetic spectrum. A first material and a second material are deposited onto a substrate. The first material may include dielectric spheres of subwavelength size that self-assemble on the substrate to form a template or scaffold with subwavelength size voids between the spheres into which the second material is deposited or filled. First and second materials are heated on the substrate at a preselected temperature to form the subwavelength coating.

High energy neutron dosimeter

DOEpatents

Sun, Rai Ko S.F.

1994-01-01

A device for measuring dose equivalents in neutron radiation fields. The device includes nested symmetrical hemispheres (forming spheres) of different neutron moderating materials that allow the measurement of dose equivalents from 0.025 eV to past 1 GeV. The layers of moderating material surround a spherical neutron counter. The neutron counter is connected by an electrical cable to an electrical sensing means which interprets the signal from the neutron counter in the center of the moderating spheres. The spherical shape of the device allows for accurate measurement of dose equivalents regardless of its positioning.

An Unusual Rolling-Sphere Phenomenon.

ERIC Educational Resources Information Center

Cromer, Alan

1996-01-01

Discusses the theory behind a study of motion where a hollow plastic sphere racing against a steel sphere in two parallel sections of inclined channeling always reaches the bottom first; once on the floor, however, the steel sphere travels faster, speeding past the plastic sphere when both are about one meter from the base of the track. (JRH)

Porous Ceramic Spheres From Cation Exchange Beads

NASA Technical Reports Server (NTRS)

Dynys, Fred

2005-01-01

This document is a slide presentation that examines the use of a simple templating process to produce hollow ceramic spheres with a pore size of 1 to 10 microns. Using ion exchange process it was determined that the method produces porous ceramic spheres with a unique structure: (i.e., inner sphere surrounded by an outer sphere.)

A Systematic Review and Meta-Analysis of Fecal Contamination and Inadequate Treatment of Packaged Water

PubMed Central

Williams, Ashley R.; Bain, Robert E. S.; Fisher, Michael B.; Cronk, Ryan; Kelly, Emma R.; Bartram, Jamie

2015-01-01

Background Packaged water products provide an increasingly important source of water for consumption. However, recent studies raise concerns over their safety. Objectives To assess the microbial safety of packaged water, examine differences between regions, country incomes, packaged water types, and compare packaged water with other water sources. Methods We performed a systematic review and meta-analysis. Articles published in English, French, Portuguese, Spanish and Turkish, with no date restrictions were identified from online databases and two previous reviews. Studies published before April 2014 that assessed packaged water for the presence of Escherichia coli, thermotolerant or total coliforms were included provided they tested at least ten samples or brands. Results A total of 170 studies were included in the review. The majority of studies did not detect fecal indicator bacteria in packaged water (78/141). Compared to packaged water from upper-middle and high-income countries, packaged water from low and lower-middle-income countries was 4.6 (95% CI: 2.6–8.1) and 13.6 (95% CI: 6.9–26.7) times more likely to contain fecal indicator bacteria and total coliforms, respectively. Compared to all other packaged water types, water from small bottles was less likely to be contaminated with fecal indicator bacteria (OR = 0.32, 95%CI: 0.17–0.58) and total coliforms (OR = 0.10, 95%CI: 0.05, 0.22). Packaged water was less likely to contain fecal indicator bacteria (OR = 0.35, 95%CI: 0.20, 0.62) compared to other water sources used for consumption. Conclusions Policymakers and regulators should recognize the potential benefits of packaged water in providing safer water for consumption at and away from home, especially for those who are otherwise unlikely to gain access to a reliable, safe water supply in the near future. To improve the quality of packaged water products they should be integrated into regulatory and monitoring frameworks. PMID:26505745

A Systematic Review and Meta-Analysis of Fecal Contamination and Inadequate Treatment of Packaged Water.

PubMed

Williams, Ashley R; Bain, Robert E S; Fisher, Michael B; Cronk, Ryan; Kelly, Emma R; Bartram, Jamie

2015-01-01

Packaged water products provide an increasingly important source of water for consumption. However, recent studies raise concerns over their safety. To assess the microbial safety of packaged water, examine differences between regions, country incomes, packaged water types, and compare packaged water with other water sources. We performed a systematic review and meta-analysis. Articles published in English, French, Portuguese, Spanish and Turkish, with no date restrictions were identified from online databases and two previous reviews. Studies published before April 2014 that assessed packaged water for the presence of Escherichia coli, thermotolerant or total coliforms were included provided they tested at least ten samples or brands. A total of 170 studies were included in the review. The majority of studies did not detect fecal indicator bacteria in packaged water (78/141). Compared to packaged water from upper-middle and high-income countries, packaged water from low and lower-middle-income countries was 4.6 (95% CI: 2.6-8.1) and 13.6 (95% CI: 6.9-26.7) times more likely to contain fecal indicator bacteria and total coliforms, respectively. Compared to all other packaged water types, water from small bottles was less likely to be contaminated with fecal indicator bacteria (OR = 0.32, 95%CI: 0.17-0.58) and total coliforms (OR = 0.10, 95%CI: 0.05, 0.22). Packaged water was less likely to contain fecal indicator bacteria (OR = 0.35, 95%CI: 0.20, 0.62) compared to other water sources used for consumption. Policymakers and regulators should recognize the potential benefits of packaged water in providing safer water for consumption at and away from home, especially for those who are otherwise unlikely to gain access to a reliable, safe water supply in the near future. To improve the quality of packaged water products they should be integrated into regulatory and monitoring frameworks.

In Situ Localized Growth of Ordered Metal Oxide Hollow Sphere Array on Microheater Platform for Sensitive, Ultra-Fast Gas Sensing.

PubMed

Rao, Ameya; Long, Hu; Harley-Trochimczyk, Anna; Pham, Thang; Zettl, Alex; Carraro, Carlo; Maboudian, Roya

2017-01-25

A simple and versatile strategy is presented for the localized on-chip synthesis of an ordered metal oxide hollow sphere array directly on a low power microheater platform to form a closely integrated miniaturized gas sensor. Selective microheater surface modification through fluorinated monolayer self-assembly and its subsequent microheater-induced thermal decomposition enables the position-controlled deposition of an ordered two-dimensional colloidal sphere array, which serves as a sacrificial template for metal oxide growth via homogeneous chemical precipitation; this strategy ensures control in both the morphology and placement of the sensing material on only the active heated area of the microheater platform, providing a major advantage over other methods of presynthesized nanomaterial integration via suspension coating or printing. A fabricated tin oxide hollow sphere-based sensor shows high sensitivity (6.5 ppb detection limit) and selectivity toward formaldehyde, and extremely fast response (1.8 s) and recovery (5.4 s) times. This flexible and scalable method can be used to fabricate high performance miniaturized gas sensors with a variety of hollow nanostructured metal oxides for a range of applications, including combining multiple metal oxides for superior sensitivity and tunable selectivity.

Aperture excited dielectric antennas

NASA Technical Reports Server (NTRS)

Crosswell, W. F.; Chatterjee, J. S.; Mason, V. B.; Tai, C. T.

1974-01-01

The results of a comprehensive experimental and theoretical study of the effect of placing dielectric objects over the aperture of waveguide antennas are presented. Experimental measurements of the radiation patterns, gain, impedance, near-field amplitude, and pattern and impedance coupling between pairs of antennas are given for various Plexiglas shapes, including the sphere and the cube, excited by rectangular, circular, and square waveguide feed apertures. The waveguide excitation of a dielectric sphere is modeled using the Huygens' source, and expressions for the resulting electric fields, directivity, and efficiency are derived. Calculations using this model show good overall agreement with experimental patterns and directivity measurements. The waveguide under an infinite dielectric slab is used as an impedance model. Calculations using this model agree qualitatively with the measured impedance data. It is concluded that dielectric loaded antennas such as the waveguide excited sphere, cube, or sphere-cylinder can produce directivities in excess of that obtained by a uniformly illuminated aperture of the same cross section, particularly for dielectric objects with dimensions of 2 wavelengths or less. It is also shown that for certain configurations coupling between two antennas of this type is less than that for the same antennas without dielectric loading.

Nutrition. Learning Activity Package.

ERIC Educational Resources Information Center

Lee, Carolyn

This learning activity package on nutrition is one of a series of 12 titles developed for use in health occupations education programs. Materials in the package include objectives, a list of materials needed, a list of definitions, information sheets, reviews (self evaluations) of portions of the content, and answers to reviews. These topics are…

Shock & Anaphylactic Shock. Learning Activity Package.

ERIC Educational Resources Information Center

Hime, Kirsten

This learning activity package on shock and anaphylactic shock is one of a series of 12 titles developed for use in health occupations education programs. Materials in the package include objectives, a list of materials needed, information sheets, reviews (self evaluations) of portions of the content, and answers to reviews. These topics are…

10 CFR 71.91 - Records.

Code of Federal Regulations, 2012 CFR

2012-01-01

... shall maintain, for a period of 3 years after the life of the packaging to which they apply, records... quality of packaging. The records to be maintained include results of the determinations required by § 71... any deficiencies noted. These records must be retained for 3 years after the life of the packaging to...

Solar water heater design package

NASA Technical Reports Server (NTRS)

1981-01-01

Package describes commercial domestic-hot-water heater with roof or rack mounted solar collectors. System is adjustable to pre-existing gas or electric hot-water house units. Design package includes drawings, description of automatic control logic, evaluation measurements, possible design variations, list of materials and installation tools, and trouble-shooting guide and manual.

A Thermodynamics Course Package in Onenote

ERIC Educational Resources Information Center

Falconer, John L.; Nicodemus, Garret D.; Medlin, J. Will; deGrazia, Janet; McDanel, Katherine P.

2014-01-01

A ready-to-use package of active-learning materials for a semester-long chemical engineering thermodynamics course was prepared for instructors, and similar materials are being prepared for a material and energy balance course. The course package includes ConcepTests, explanations of the ConcepTests for instructors, links to screencasts, chapter…

Oral Hygiene. Learning Activity Package.

ERIC Educational Resources Information Center

Hime, Kirsten

This learning activity package on oral hygiene is one of a series of 12 titles developed for use in health occupations education programs. Materials in the package include objectives, a list of materials needed, a list of definitions, information sheets, reviews (self evaluations) of portions of the content, and answers to reviews. These topics…

14 CFR 60.13 - FSTD objective data requirements.

Code of Federal Regulations, 2014 CFR

2014-01-01

..., the data made available to the NSPM (the validation data package) must include the aircraft...) The validation data package may contain flight test data from a source in addition to or independent..., as described in the applicable QPS. (c) The validation data package may also contain predicted data...

14 CFR 60.13 - FSTD objective data requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

..., the data made available to the NSPM (the validation data package) must include the aircraft...) The validation data package may contain flight test data from a source in addition to or independent..., as described in the applicable QPS. (c) The validation data package may also contain predicted data...

14 CFR 60.13 - FSTD objective data requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

..., the data made available to the NSPM (the validation data package) must include the aircraft...) The validation data package may contain flight test data from a source in addition to or independent..., as described in the applicable QPS. (c) The validation data package may also contain predicted data...

14 CFR 60.13 - FSTD objective data requirements.

Code of Federal Regulations, 2012 CFR

2012-01-01

..., the data made available to the NSPM (the validation data package) must include the aircraft...) The validation data package may contain flight test data from a source in addition to or independent..., as described in the applicable QPS. (c) The validation data package may also contain predicted data...

14 CFR 60.13 - FSTD objective data requirements.

Code of Federal Regulations, 2013 CFR

2013-01-01

..., the data made available to the NSPM (the validation data package) must include the aircraft...) The validation data package may contain flight test data from a source in addition to or independent..., as described in the applicable QPS. (c) The validation data package may also contain predicted data...

Grooming. Learning Activity Package.

ERIC Educational Resources Information Center

Stark, Pamela

This learning activity package on grooming for health workers is one of a series of 12 titles developed for use in health occupations education programs. Materials in the package include objectives, a list of materials needed, information sheets, reviews (self evaluations) of portions of the content, and answers to reviews. These topics are…

Tractor Mechanics: Learning Activity Packages 1-19.

ERIC Educational Resources Information Center

Clemson Univ., SC. Vocational Education Media Center.

Learning activity packages are presented for teaching tractor mechanics. The first of two sections deals with miscellaneous tasks and contains learning activity packages on cleaning the tractor and receiving new tractor parts. Section 2 is concerned with maintaining and servicing the electrical system, and it includes the following learning…

Documentation for the MODFLOW 6 Groundwater Flow Model

USGS Publications Warehouse

Langevin, Christian D.; Hughes, Joseph D.; Banta, Edward R.; Niswonger, Richard G.; Panday, Sorab; Provost, Alden M.

2017-08-10

This report documents the Groundwater Flow (GWF) Model for a new version of MODFLOW called MODFLOW 6. The GWF Model for MODFLOW 6 is based on a generalized control-volume finite-difference approach in which a cell can be hydraulically connected to any number of surrounding cells. Users can define the model grid using one of three discretization packages, including (1) a structured discretization package for defining regular MODFLOW grids consisting of layers, rows, and columns, (2) a discretization by ver­tices package for defining layered unstructured grids consisting of layers and cells, and (3) a general unstruc­tured discretization package for defining flexible grids comprised of cells and their connection properties. For layered grids, a new capability is available for removing thin cells and vertically connecting cells overlying and underlying the thin cells. For complex problems involving water-table conditions, an optional Newton-Raphson formulation, based on the formulations in MODFLOW-NWT and MODFLOW-USG, can be acti­vated. Use of the Newton-Raphson formulation will often improve model convergence and allow solutions to be obtained for difficult problems that cannot be solved using the traditional wetting and drying approach. The GWF Model is divided into “packages,” as was done in previous MODFLOW versions. A package is the part of the model that deals with a single aspect of simulation. Packages included with the GWF Model include those related to internal calculations of groundwater flow (discretization, initial conditions, hydraulic conduc­tance, and storage), stress packages (constant heads, wells, recharge, rivers, general head boundaries, drains, and evapotranspiration), and advanced stress packages (streamflow routing, lakes, multi-aquifer wells, and unsaturated zone flow). An additional package is also available for moving water available in one package into the individual features of the advanced stress packages. The GWF Model also has packages for obtaining and controlling output from the model. This report includes detailed explanations of physical and mathematical concepts on which the GWF Model and its packages are based.Like its predecessors, MODFLOW 6 is based on a highly modular structure; however, this structure has been extended into an object-oriented framework. The framework includes a robust and generalized numeri­cal solution object, which can be used to solve many different types of models. The numerical solution object has several different matrix preconditioning options as well as several methods for solving the linear system of equations. In this new framework, the GWF Model itself is an object as are each of the GWF Model packages. A benefit of the object-oriented structure is that multiple objects of the same type can be used in a single sim­ulation. Thus, a single forward run with MODFLOW 6 may contain multiple GWF Models. GWF Models can be hydraulically connected using GWF-GWF Exchange objects. Connecting GWF models in different ways permits the user to utilize a local grid refinement strategy consisting of parent and child models or to couple adjacent GWF Models. An advantage of the approach implemented in MODFLOW 6 is that multiple models and their exchanges can be incorporated into a single numerical solution object. With this design, models can be tightly coupled at the matrix level.

Finite-size radiation force correction for inviscid spheres in standing waves.

PubMed

Marston, Philip L

2017-09-01

Yosioka and Kawasima gave a widely used approximation for the acoustic radiation force on small liquid spheres surrounded by an immiscible liquid in 1955. Considering the liquids to be inviscid with negligible thermal dissipation, in their approximation the force on the sphere is proportional to the sphere's volume and the levitation position in a vertical standing wave becomes independent of the size. The analysis given here introduces a small correction term proportional to the square of the sphere's radius relative to the aforementioned small-sphere force. The significance of this term also depends on the relative density and sound velocity of the sphere. The improved approximation is supported by comparison with the exact partial-wave-series based radiation force for ideal fluid spheres in ideal fluids.

Template method synthesis of mesoporous carbon spheres and its applications as supercapacitors

PubMed Central

2012-01-01

Mesoporous carbon spheres (MCS) have been fabricated from structured mesoporous silica sphere using chemical vapor deposition (CVD) with ethylene as a carbon feedstock. The mesoporous carbon spheres have a high specific surface area of 666.8 m2/g and good electrochemical properties. The mechanism of formation mesoporous carbon spheres (carbon spheres) is investigated. The important thing is a surfactant hexadecyl trimethyl ammonium bromide (CTAB), which accelerates the process of carbon deposition. An additional advantage of this surfactant is an increase the yield of product. These mesoporous carbon spheres, which have good electrochemical properties is suitable for supercapacitors. PMID:22643113

Dispersivity of Bidisperse Packings of Spheres and Evidence for Distinct Random Structures

NASA Astrophysics Data System (ADS)

Scheven, U. M.

2018-05-01

The intrinsic longitudinal and transverse dispersivity of bidisperse random packings of spheres with size ratio 5 ∶1 was determined by pulsed field gradient nuclear magnetic resonance, in the dilute regime where small spheres occupy between 0% and 5% of the packings' volume. Small spheres plugging pores systematically raise the mechanical transverse and longitudinal dispersivity above that of reference packings of monodisperse spheres. NMR-derived porosities, widths of velocity distributions, and dispersivities reveal distinct states of structural disorder above and below a relative sphere concentration n /N =1 , where n and N are the number densities of small and large spheres.

A Design Study of the Inflated Sphere Landing Vehicle, Including the Landing Performance and the Effects of Deviations from Design Conditions

NASA Technical Reports Server (NTRS)

Martin, E. Dale

1961-01-01

The impact motion of the inflated sphere landing vehicle with a payload centrally supported from the spherical skin by numerous cords has been determined on the assumption of uniform isentropic gas compression during impact. The landing capabilities are determined for a system containing suspension cords of constant cross section. The effects of deviations in impact velocity and initial gas temperature from the design conditions are studied. Also discussed are the effects of errors in the time at which the skin is ruptured. These studies indicate how the design parameters should be chosen to insure reliability of the landing system. Calculations have been made and results are presented for a sphere inflated with hydrogen, landing on the moon in the absence of an atmosphere. The results are presented for one value of the skin-strength parameter.

Extreme AO coronagraphy laboratory demonstration in the context of SPHERE

NASA Astrophysics Data System (ADS)

Martinez, P.; Aller Carpentier, E.; Kasper, M.

2010-10-01

The exoplanetary science through direct imaging and spectroscopy will largely expand with the very soon raise of new instruments at the VLT (SPHERE), Gemini (GPI), and Subaru (HiCIAO) observatories. All these ground-based adaptive optics instruments include extremely high performance adaptive optics (XAO) system, advanced starlight cancellation techniques (e.g. coronagraphy), and speckle calibration techniques (e.g. spectral, angular, or polarimetry). In this context we report laboratory results obtained with the High-Order Test bench (HOT), the adaptive optics facility at the European Southern Observatory headquarters. Under 0.5 arcsec dynamical seeing, efficiently corrected by an XAO system delivering H-band Strehl ratio above 90%, we discuss contrast levels obtained with an apodized pupil Lyot coronagraph using differential imaging techniques (spectral and polarimetric). Accounting for system differences (e.g. deformable mirror actuator number), we demonstrate a good agreement between experimental results and expectations for SPHERE, or GPI, while we already met HiCIAO contrast goals.

HEALPix: A Framework for High-Resolution Discretization and Fast Analysis of Data Distributed on the Sphere

NASA Technical Reports Server (NTRS)

Gorski, K. M.; Hivon, Eric; Banday, A. J.; Wandelt, Benjamin D.; Hansen, Frode K.; Reinecke, Mstvos; Bartelmann, Matthia

2005-01-01

HEALPix the Hierarchical Equal Area isoLatitude Pixelization is a versatile structure for the pixelization of data on the sphere. An associated library of computational algorithms and visualization software supports fast scientific applications executable directly on discretized spherical maps generated from very large volumes of astronomical data. Originally developed to address the data processing and analysis needs of the present generation of cosmic microwave background experiments (e.g., BOOMERANG, WMAP), HEALPix can be expanded to meet many of the profound challenges that will arise in confrontation with the observational output of future missions and experiments, including, e.g., Planck, Herschel, SAFIR, and the Beyond Einstein inflation probe. In this paper we consider the requirements and implementation constraints on a framework that simultaneously enables an efficient discretization with associated hierarchical indexation and fast analysis/synthesis of functions defined on the sphere. We demonstrate how these are explicitly satisfied by HEALPix.

Marcus equation

DOE R&D Accomplishments Database

1998-09-21

In the late 1950s to early 1960s Rudolph A. Marcus developed a theory for treating the rates of outer-sphere electron-transfer reactions. Outer-sphere reactions are reactions in which an electron is transferred from a donor to an acceptor without any chemical bonds being made or broken. (Electron-transfer reactions in which bonds are made or broken are referred to as inner-sphere reactions.) Marcus derived several very useful expressions, one of which has come to be known as the Marcus cross-relation or, more simply, as the Marcus equation. It is widely used for correlating and predicting electron-transfer rates. For his contributions to the understanding of electron-transfer reactions, Marcus received the 1992 Nobel Prize in Chemistry. This paper discusses the development and use of the Marcus equation. Topics include self-exchange reactions; net electron-transfer reactions; Marcus cross-relation; and proton, hydride, atom and group transfers.

A Public/Private Extension of Conway's Accessor Model

NASA Technical Reports Server (NTRS)

McCann, Karen M.; Yarrow, Maurice

2000-01-01

We present a new object-oriented model for a Perl package, based on Damien Conway's 'accessor' model. Our model includes both public and private data; it uses strategies to reduce a package namespace, but still maintains a robust and error-trapped approach. With this extended model we can make any package data or functions 'private', as well as 'public'. (Note: 'namespace' in this context means all the names, variables and subs, associated with a package.)

A Package of Information as the Planck Unit of Information and Also as a Fundamental Physical (Universal) Constant

NASA Astrophysics Data System (ADS)

Gholibeigian, Hassan

Dimension of information as the fifth dimension of the universe including packages of new information, is nested with space-time. Distributed density of information is matched on its correspondence distributed mater in space-time. Fundamental particle (string) like photon and graviton needs a package of information including its exact quantum state and law for process and travel a Planck length in a Planck time. This process is done via sub-particles (substrings). Processed information is carried by particle as the universe's history. My proposed formula for Planck unit of information (IP) and also for Fundamental Physical (Universal) Constant is: IP =lP ct P =1 Planck length lP, Planck time tP, and c , is light speed. Also my proposed formula for calculation of the packages is: I =tP- 1 . τ , in which, I is number of packages, and τ is lifetime of the particle. ``Communication of information'' as a ``fundamental symmetry'' leads phenomena. Packages should be always up to date including new information for evolution of the Universe. But, where come from or how are created new information which Hawking and his colleagues forgot it bring inside the black hole and leave it behind the horizon in form of soft hair?

CheMentor Software System by H. A. Peoples

NASA Astrophysics Data System (ADS)

Reid, Brian P.

1997-09-01

CheMentor Software System H. A. Peoples. Computerized Learning Enhancements: http://www.ecis.com/~clehap; email: clehap@ecis.com; 1996 - 1997. CheMentor is a series of software packages for introductory-level chemistry, which includes Practice Items (I), Stoichiometry (I), Calculating Chemical Formulae, and the CheMentor Toolkit. The first three packages provide practice problems for students and various types of help to solve them; the Toolkit includes "calculators" for determining chemical quantities as well as the Practice Items (I) set of problems. The set of software packages is designed so that each individual product acts as a module of a common CheMentor program. As the name CheMentor implies, the software is designed as a "mentor" for students learning introductory chemistry concepts and problems. The typical use of the software would be by individual students (or perhaps small groups) as an adjunct to lectures. CheMentor is a HyperCard application and the modules are HyperCard stacks. The requirements to run the packages include a Macintosh computer with at least 1 MB of RAM, a hard drive with several MB of available space depending upon the packages selected (10 MB were required for all the packages reviewed here), and the Mac operating system 6.0.5 or later.

Technique and cue selection for graphical presentation of generic hyperdimensional data

NASA Astrophysics Data System (ADS)

Howard, Lee M.; Burton, Robert P.

2013-12-01

Several presentation techniques have been created for visualization of data with more than three variables. Packages have been written, each of which implements a subset of these techniques. However, these packages generally fail to provide all the features needed by the user during the visualization process. Further, packages generally limit support for presentation techniques to a few techniques. A new package called Petrichor accommodates all necessary and useful features together in one system. Any presentation technique may be added easily through an extensible plugin system. Features are supported by a user interface that allows easy interaction with data. Annotations allow users to mark up visualizations and share information with others. By providing a hyperdimensional graphics package that easily accommodates presentation techniques and includes a complete set of features, including those that are rarely or never supported elsewhere, the user is provided with a tool that facilitates improved interaction with multivariate data to extract and disseminate information.

Surface gloss and color perception of 3D objects.

PubMed

Xiao, Bei; Brainard, David H

2008-01-01

Two experiments explore the color perception of objects in complex scenes. The first experiment examines the color perception of objects across variation in surface gloss. Observers adjusted the color appearance of a matte sphere to match that of a test sphere. Across conditions we varied the body color and glossiness of the test sphere. The data indicate that observers do not simply match the average light reflected from the test. Indeed, the visual system compensates for the physical effect of varying the gloss, so that appearance is stabilized relative to what is predicted by the spatial average. The second experiment examines how people perceive color across locations on an object. We replaced the test sphere with a soccer ball that had one of its hexagonal faces colored. Observers were asked to adjust the match sphere have the same color appearance as this test patch. The test patch could be located at either an upper or lower location on the soccer ball. In addition, we varied the surface gloss of the entire soccer ball (including the test patch). The data show that there is an effect of test patch location on observers' color matching, but this effect is small compared to the physical change in the average light reflected from the test patch across the two locations. In addition, the effect of glossy highlights on the color appearance of the test patch was consistent with the results from Experiment 1.

Surface gloss and color perception of 3D objects

PubMed Central

Xiao, Bei; Brainard, David H.

2008-01-01

Two experiments explore the color perception of objects in complex scenes. The first experiment examines the color perception of objects across variation in surface gloss. Observers adjusted the color appearance of a matte sphere to match that of a test sphere. Across conditions we varied the body color and glossiness of the test sphere. The data indicate that observers do not simply match the average light reflected from the test. Indeed, the visual system compensates for the physical effect of varying the gloss, so that appearance is stabilized relative to what is predicted by the spatial average. The second experiment examines how people perceive color across locations on an object. We replaced the test sphere with a soccer ball that had one of its hexagonal faces colored. Observers were asked to adjust the match sphere have the same color appearance as this test patch. The test patch could be located at either an upper or lower location on the soccer ball. In addition, we varied the surface gloss of the entire soccer ball (including the test patch). The data show that there is an effect of test patch location on observers’ color matching, but this effect is small compared to the physical change in the average light reflected from the test patch across the two locations. In addition, the effect of glossy highlights on the color appearance of the test patch was consistent with the results from Experiment 1. PMID:18598406

Acceleration from short-duration blast

NASA Astrophysics Data System (ADS)

Ritzel, D. V.; Van Albert, S.; Sajja, V.; Long, J.

2018-01-01

The blast-induced motion of spheres has been studied experimentally where the shock wave is rapidly decaying during the period that quasi-steady acceleration would be developed in the case of a step-function shock wave as considered in most shock-tube studies. The motion of sphere models ranging from 39 to 251 mm in diameter and having a range of densities was assessed using the "free-flight" method in a simulator specially designed to replicate the decaying shock wave profile of spherical blast including negative phase and positive entropy gradient. A standardized blast-wave simulation of 125 kPa and 6-ms positive-phase duration was applied for all experiments. In all cases, there are three phases to the motion: a relatively low "kickoff" velocity from the shock diffraction, acceleration or deceleration during the positive duration, then deceleration through the negative phase and subsequent quiescent air. The unexpected deceleration of larger spheres after their kickoff velocity during the decaying yet high-speed flow of the blast wave seems associated with the persistence of a ring vortex on the downstream side of the sphere. The flow is entirely unsteady with initial forces dominated by the shock diffraction; therefore, the early motion of spheres under such conditions is not governed by quasi-steady drag as in classical aerodynamics. The work will help establish scaling rules for model studies of blast-induced motion relevant to improvised explosive devices, and preliminary results are shown for motion imparted to a human skull surrogate.

Welding at the Kennedy Space Center.

NASA Technical Reports Server (NTRS)

Clautice, W. E.

1973-01-01

Brief description of the nature of the mechanical equipment at a space launch complex from a welding viewpoint. including an identification of the major welding applications used in the construction of this complex. The role played by welding in the ground support equipment is noted, including the welded structures and systems required in the vehicle assembly building, the mobile launchers, transporters, mobile service structure, launch pad and launch site, the propellants system, the pneumatics system, and the environmental control system. The welding processes used at the Kennedy Space Center are reviewed, and a particularly detailed account is given of the design and fabrication of the liquid hydrogen and liquid oxygen storage spheres and piping. Finally, the various methods of testing and inspecting the storage spheres are cited.

Waste Package Component Design Methodology Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

D.C. Mecham

2004-07-12

This Executive Summary provides an overview of the methodology being used by the Yucca Mountain Project (YMP) to design waste packages and ancillary components. This summary information is intended for readers with general interest, but also provides technical readers a general framework surrounding a variety of technical details provided in the main body of the report. The purpose of this report is to document and ensure appropriate design methods are used in the design of waste packages and ancillary components (the drip shields and emplacement pallets). The methodology includes identification of necessary design inputs, justification of design assumptions, and usemore » of appropriate analysis methods, and computational tools. This design work is subject to ''Quality Assurance Requirements and Description''. The document is primarily intended for internal use and technical guidance for a variety of design activities. It is recognized that a wide audience including project management, the U.S. Department of Energy (DOE), the U.S. Nuclear Regulatory Commission, and others are interested to various levels of detail in the design methods and therefore covers a wide range of topics at varying levels of detail. Due to the preliminary nature of the design, readers can expect to encounter varied levels of detail in the body of the report. It is expected that technical information used as input to design documents will be verified and taken from the latest versions of reference sources given herein. This revision of the methodology report has evolved with changes in the waste package, drip shield, and emplacement pallet designs over many years and may be further revised as the design is finalized. Different components and analyses are at different stages of development. Some parts of the report are detailed, while other less detailed parts are likely to undergo further refinement. The design methodology is intended to provide designs that satisfy the safety and operational requirements of the YMP. Four waste package configurations have been selected to illustrate the application of the methodology during the licensing process. These four configurations are the 21-pressurized water reactor absorber plate waste package (21-PWRAP), the 44-boiling water reactor waste package (44-BWR), the 5 defense high-level radioactive waste (HLW) DOE spent nuclear fuel (SNF) codisposal short waste package (5-DHLWDOE SNF Short), and the naval canistered SNF long waste package (Naval SNF Long). Design work for the other six waste packages will be completed at a later date using the same design methodology. These include the 24-boiling water reactor waste package (24-BWR), the 21-pressurized water reactor control rod waste package (21-PWRCR), the 12-pressurized water reactor waste package (12-PWR), the 5 defense HLW DOE SNF codisposal long waste package (5-DHLWDOE SNF Long), the 2 defense HLW DOE SNF codisposal waste package (2-MC012-DHLW), and the naval canistered SNF short waste package (Naval SNF Short). This report is only part of the complete design description. Other reports related to the design include the design reports, the waste package system description documents, manufacturing specifications, and numerous documents for the many detailed calculations. The relationships between this report and other design documents are shown in Figure 1.« less

Readability of medicinal package leaflets: a systematic review

PubMed Central

Pires, Carla; Vigário, Marina; Cavaco, Afonso

2015-01-01

OBJECTIVE To review studies on the readability of package leaflets of medicinal products for human use. METHODS We conducted a systematic literature review between 2008 and 2013 using the keywords “Readability and Package Leaflet” and “Readability and Package Insert” in the academic search engine Biblioteca do Conhecimento Online, comprising different bibliographic resources/databases. The preferred reporting items for systematic reviews and meta-analyses criteria were applied to prepare the draft of the report. Quantitative and qualitative original studies were included. Opinion or review studies not written in English, Portuguese, Italian, French, or Spanish were excluded. RESULTS We identified 202 studies, of which 180 were excluded and 22 were enrolled [two enrolling healthcare professionals, 10 enrolling other type of participants (including patients), three focused on adverse reactions, and 7 descriptive studies]. The package leaflets presented various readability problems, such as complex and difficult to understand texts, small font size, or few illustrations. The main methods to assess the readability of the package leaflet were usability tests or legibility formulae. Limitations with these methods included reduced number of participants; lack of readability formulas specifically validated for specific languages (e.g., Portuguese); and absence of an assessment on patients literacy, health knowledge, cognitive skills, levels of satisfaction, and opinions. CONCLUSIONS Overall, the package leaflets presented various readability problems. In this review, some methodological limitations were identified, including the participation of a limited number of patients and healthcare professionals, the absence of prior assessments of participant literacy, humor or sense of satisfaction, or the predominance of studies not based on role-plays about the use of medicines. These limitations should be avoided in future studies and be considered when interpreting the results. PMID:25741660

Readability of medicinal package leaflets: a systematic review.

PubMed

Pires, Carla; Vigário, Marina; Cavaco, Afonso

2015-01-01

OBJECTIVE To review studies on the readability of package leaflets of medicinal products for human use. METHODS We conducted a systematic literature review between 2008 and 2013 using the keywords "Readability and Package Leaflet" and "Readability and Package Insert" in the academic search engine Biblioteca do Conhecimento Online, comprising different bibliographic resources/databases. The preferred reporting items for systematic reviews and meta-analyses criteria were applied to prepare the draft of the report. Quantitative and qualitative original studies were included. Opinion or review studies not written in English, Portuguese, Italian, French, or Spanish were excluded. RESULTS We identified 202 studies, of which 180 were excluded and 22 were enrolled [two enrolling healthcare professionals, 10 enrolling other type of participants (including patients), three focused on adverse reactions, and 7 descriptive studies]. The package leaflets presented various readability problems, such as complex and difficult to understand texts, small font size, or few illustrations. The main methods to assess the readability of the package leaflet were usability tests or legibility formulae. Limitations with these methods included reduced number of participants; lack of readability formulas specifically validated for specific languages (e.g., Portuguese); and absence of an assessment on patients literacy, health knowledge, cognitive skills, levels of satisfaction, and opinions. CONCLUSIONS Overall, the package leaflets presented various readability problems. In this review, some methodological limitations were identified, including the participation of a limited number of patients and healthcare professionals, the absence of prior assessments of participant literacy, humor or sense of satisfaction, or the predominance of studies not based on role-plays about the use of medicines. These limitations should be avoided in future studies and be considered when interpreting the results.

75 FR 5375 - Hazardous Material; Miscellaneous Packaging Amendments

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-02

...In this final rule, PHMSA is amending packaging requirements in the Hazardous Materials Regulations to enhance compliance flexibility, improve clarity, and reduce regulatory burdens. Specifically, we are revising several packaging related definitions; adding provisions to allow more flexibility when preparing and transmitting closure instructions, including conditions under which closure instructions may be transmitted electronically; adding a requirement for shippers to retain packaging closure instructions; incorporating new language that will allow for a practicable means of stenciling the ``UN'' symbol on packagings; and clarifying a requirement to document the methodology used when determining whether a change in packaging configuration requires retesting as a new design or may be considered a variation of a previously tested design. This final rule also incorporates requirements for construction, maintenance, and use of Large Packagings.

Apparatus and method for skin packaging articles

NASA Technical Reports Server (NTRS)

Madsen, B.; Pozsony, E. R.; Collin, E. E. (Inventor)

1973-01-01

A system for skin packaging articles including a loading zone for positioning articles to be packaged upon a substrate, a thermoplastic film heating and vacuum operated skin packaging zone for covering the articles with film laminated to the substrate and a slitting zone for separating and trimming the individual skin packaged articles. The articles are passed to the successive zones. The loading zone may be adapted for conveyorized instead of hand loading. In some cases, where only transverse cutting of the film web is necessary, it may be desirable to eliminate the slitting zone and remove the skin packaged article or articles directly from the packaging zone. A conveniently located operating panel contains controls for effecting automatic, semiautomatic or manual operation of the entire system of any portions in any manner desired.

Tobacco packaging and labeling policies under the U.S. Tobacco Control Act: research needs and priorities.

PubMed

Hammond, David

2012-01-01

The Family Smoking Prevention and Tobacco Control Act (the "Act"), enacted in June 2009, gave the U.S. Food and Drug Administration authority to regulate tobacco products. The current paper reviews the provisions for packaging and labeling, including the existing evidence and research priorities. Narrative review using electronic literature search of published and unpublished sources in 3 primary areas: health warnings, constituent labeling, and prohibitions on the promotional elements of packaging. The Act requires 9 pictorial health warnings covering half of cigarette packages and 4 text warnings covering 30% of smokeless tobacco packages. The Act also prohibits potentially misleading information on packaging, including the terms "light" and "mild," and provides a mandate to require disclosure of chemical constituents on packages. Many of the specific regulatory provisions are based on the extent to which they promote "greater public understanding of the risks of tobacco." As a result, research on consumer perceptions has the potential to shape the design and renewal of health warnings and to determine what, if any, information on product constituents should appear on packages. Research on consumer perceptions of existing and novel tobacco products will also be critical to help identify potentially misleading information that should be restricted under the Act. Packaging and labeling regulations required under the Act will bring the United States in line with international standards. There is an immediate need for research to evaluate these measures to guide future regulatory action.

fgui: A Method for Automatically Creating Graphical User Interfaces for Command-Line R Packages

PubMed Central

Hoffmann, Thomas J.; Laird, Nan M.

2009-01-01

The fgui R package is designed for developers of R packages, to help rapidly, and sometimes fully automatically, create a graphical user interface for a command line R package. The interface is built upon the Tcl/Tk graphical interface included in R. The package further facilitates the developer by loading in the help files from the command line functions to provide context sensitive help to the user with no additional effort from the developer. Passing a function as the argument to the routines in the fgui package creates a graphical interface for the function, and further options are available to tweak this interface for those who want more flexibility. PMID:21625291

Flat-plate solar collector - installation package

NASA Technical Reports Server (NTRS)

1978-01-01

Package includes installation, operation and maintenance manual for collector, analysis of safety hazards, special handling instructions, materials list, installation drawings, and warranty and certification statement. Manual includes instructions for roof preparation and for preparing collector for installation. Several pages are devoted to major and minor repairs.

Biomolecule-assisted construction of cadmium sulfide hollow spheres with structure-dependent photocatalytic activity.

PubMed

Wei, Chengzhen; Zang, Wenzhe; Yin, Jingzhou; Lu, Qingyi; Chen, Qun; Liu, Rongmei; Gao, Feng

2013-02-25

In this study, we report the synthesis of monodispersive solid and hollow CdS spheres with structure-dependent photocatalytic abilities for dye photodegradation. The monodispersive CdS nanospheres were constructed with the assistance of the soulcarboxymthyi chitosan biopolymer under hydrothermal conditions. The solid CdS spheres were corroded by ammonia to form hollow CdS nanospheres through a dissolution-reprecipitation mechanism. Their visible-light photocatalytic activities were investigated, and the results show that both the solid and the hollow CdS spheres have visible-light photocatalytic abilities for the photodegradation of dyes. The photocatalytic properties of the CdS spheres were demonstrated to be structure dependent. Although the nanoparticles comprising the hollow spheres have larger sizes than those comprising the solid spheres, the hollow CdS spheres have better photocatalytic performances than the solid CdS spheres, which can be attributed to the special hollow structure. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A hardware investigation of robotic SPECT for functional and molecular imaging onboard radiation therapy systems

PubMed Central

Yan, Susu; Bowsher, James; Tough, MengHeng; Cheng, Lin; Yin, Fang-Fang

2014-01-01

Purpose: To construct a robotic SPECT system and to demonstrate its capability to image a thorax phantom on a radiation therapy flat-top couch, as a step toward onboard functional and molecular imaging in radiation therapy. Methods: A robotic SPECT imaging system was constructed utilizing a gamma camera detector (Digirad 2020tc) and a robot (KUKA KR150 L110 robot). An imaging study was performed with a phantom (PET CT PhantomTM), which includes five spheres of 10, 13, 17, 22, and 28 mm diameters. The phantom was placed on a flat-top couch. SPECT projections were acquired either with a parallel-hole collimator or a single-pinhole collimator, both without background in the phantom and with background at 1/10th the sphere activity concentration. The imaging trajectories of parallel-hole and pinhole collimated detectors spanned 180° and 228°, respectively. The pinhole detector viewed an off-centered spherical common volume which encompassed the 28 and 22 mm spheres. The common volume for parallel-hole system was centered at the phantom which encompassed all five spheres in the phantom. The maneuverability of the robotic system was tested by navigating the detector to trace the phantom and flat-top table while avoiding collision and maintaining the closest possible proximity to the common volume. The robot base and tool coordinates were used for image reconstruction. Results: The robotic SPECT system was able to maneuver parallel-hole and pinhole collimated SPECT detectors in close proximity to the phantom, minimizing impact of the flat-top couch on detector radius of rotation. Without background, all five spheres were visible in the reconstructed parallel-hole image, while four spheres, all except the smallest one, were visible in the reconstructed pinhole image. With background, three spheres of 17, 22, and 28 mm diameters were readily observed with the parallel-hole imaging, and the targeted spheres (22 and 28 mm diameters) were readily observed in the pinhole region-of-interest imaging. Conclusions: Onboard SPECT could be achieved by a robot maneuvering a SPECT detector about patients in position for radiation therapy on a flat-top couch. The robot inherent coordinate frames could be an effective means to estimate detector pose for use in SPECT image reconstruction. PMID:25370663

Can the Equivalent Sphere Model Approximate Organ Doses in Space?

NASA Technical Reports Server (NTRS)

Lin, Zi-Wei

2007-01-01

For space radiation protection it is often useful to calculate dose or dose,equivalent in blood forming organs (BFO). It has been customary to use a 5cm equivalent sphere to. simulate the BFO dose. However, many previous studies have concluded that a 5cm sphere gives very different dose values from the exact BFO values. One study [1] . concludes that a 9 cm sphere is a reasonable approximation for BFO'doses in solar particle event environments. In this study we use a deterministic radiation transport [2] to investigate the reason behind these observations and to extend earlier studies. We take different space radiation environments, including seven galactic cosmic ray environments and six large solar particle events, and calculate the dose and dose equivalent in the skin, eyes and BFO using their thickness distribution functions from the CAM (Computerized Anatomical Man) model [3] The organ doses have been evaluated with a water or aluminum shielding of an areal density from 0 to 20 g/sq cm. We then compare with results from the equivalent sphere model and determine in which cases and at what radius parameters the equivalent sphere model is a reasonable approximation. Furthermore, we address why the equivalent sphere model is not a good approximation in some cases. For solar particle events, we find that the radius parameters for the organ dose equivalent increase significantly with the shielding thickness, and the model works marginally for BFO but is unacceptable for the eye or the skin. For galactic cosmic rays environments, the equivalent sphere model with an organ-specific constant radius parameter works well for the BFO dose equivalent, marginally well for the BFO dose and the dose equivalent of the eye or the skin, but is unacceptable for the dose of the eye or the skin. The ranges of the radius parameters are also being investigated, and the BFO radius parameters are found to be significantly, larger than 5 cm in all cases, consistent with the conclusion of an earlier study [I]. The radius parameters for the dose equivalent in GCR environments are approximately between 10 and I I cm for the BFO, 3.7 to 4.8 cm for the eye, and 3.5 to 5.6 cm for the skin; while the radius parameters are between 10 and 13 cm for the BFO dose.

A hardware investigation of robotic SPECT for functional and molecular imaging onboard radiation therapy systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yan, Susu, E-mail: susu.yan@duke.edu; Tough, MengHeng; Bowsher, James

Purpose: To construct a robotic SPECT system and to demonstrate its capability to image a thorax phantom on a radiation therapy flat-top couch, as a step toward onboard functional and molecular imaging in radiation therapy. Methods: A robotic SPECT imaging system was constructed utilizing a gamma camera detector (Digirad 2020tc) and a robot (KUKA KR150 L110 robot). An imaging study was performed with a phantom (PET CT Phantom{sup TM}), which includes five spheres of 10, 13, 17, 22, and 28 mm diameters. The phantom was placed on a flat-top couch. SPECT projections were acquired either with a parallel-hole collimator ormore » a single-pinhole collimator, both without background in the phantom and with background at 1/10th the sphere activity concentration. The imaging trajectories of parallel-hole and pinhole collimated detectors spanned 180° and 228°, respectively. The pinhole detector viewed an off-centered spherical common volume which encompassed the 28 and 22 mm spheres. The common volume for parallel-hole system was centered at the phantom which encompassed all five spheres in the phantom. The maneuverability of the robotic system was tested by navigating the detector to trace the phantom and flat-top table while avoiding collision and maintaining the closest possible proximity to the common volume. The robot base and tool coordinates were used for image reconstruction. Results: The robotic SPECT system was able to maneuver parallel-hole and pinhole collimated SPECT detectors in close proximity to the phantom, minimizing impact of the flat-top couch on detector radius of rotation. Without background, all five spheres were visible in the reconstructed parallel-hole image, while four spheres, all except the smallest one, were visible in the reconstructed pinhole image. With background, three spheres of 17, 22, and 28 mm diameters were readily observed with the parallel-hole imaging, and the targeted spheres (22 and 28 mm diameters) were readily observed in the pinhole region-of-interest imaging. Conclusions: Onboard SPECT could be achieved by a robot maneuvering a SPECT detector about patients in position for radiation therapy on a flat-top couch. The robot inherent coordinate frames could be an effective means to estimate detector pose for use in SPECT image reconstruction.« less

Psychosocial interventions among children and adolescents

PubMed Central

Jayarajan, Deepak; Jacob, Preeti

2018-01-01

Substance use disorders in children and adolescents are a significant cause of concern as they can have long term implications in practically every sphere. The etiological factors that contribute to substance use disorders are complex and the formulation must amalgamate and synthesize all the different factors including the predisposing, perpetuating, precipitating and protective factors in order to plan management. Interventions must stem from this comprehensive formulation and must be child-focused, multidisciplinary, multisystemic, with strong family participation and community involvement. The treating team must actively collaborate with the young person and help him/her understand the rationale for treatment in order for them to engage in it. Assessment and treatment of comorbidities are an important part of intervention package. Skill training for problem solving, emotional regulation, social skills, and communication are an essential part of the treatment for substance use disorders in adolescents. Relapse prevention strategies, including how to seek help when there is a lapse must be part and parcel of the interventions delivered to the young person. Substance use disorder interventions must be part of a larger plan that addresses other areas of concern in the young person's life. While there are few studies, and so a relatively weak and preliminary evidence base for pharmacotherapeutic interventions, early evidence shows that their combination with psychosocial interventions may have a synergistic effect on substance use reduction. Substance use disorders affect the entire family and the community at large and thus must be treated holistically, but by individualising the treatment to suit the needs of that particular child and family. PMID:29540929

Microwave-Assisted Solvothermal Synthesis of VO2 Hollow Spheres and Their Conversion into V2O5 Hollow Spheres with Improved Lithium Storage Capability.

PubMed

Pan, Jing; Zhong, Li; Li, Ming; Luo, Yuanyuan; Li, Guanghai

2016-01-22

Monodispersed hierarchically structured V2O5 hollow spheres were successfully obtained from orthorhombic VO2 hollow spheres, which are in turn synthesized by a simple template-free microwave-assisted solvothermal method. The structural evolution of VO2 hollow spheres has been studied and explained by a chemically induced self-transformation process. The reaction time and water content in the reaction solution have a great influence on the morphology and phase structure of the resulting products in the solvothermal reaction. The diameter of the VO2 hollow spheres can be regulated simply by changing vanadium ion content in the reaction solution. The VO2 hollow spheres can be transformed into V2O5 hollow spheres with nearly no morphological change by annealing in air. The nanorods composed of V2O5 hollow spheres have an average length of about 70 nm and width of about 19 nm. When used as a cathode material for lithium-ion batteries, the V2O5 hollow spheres display a diameter-dependent electrochemical performance, and the 440 nm hollow spheres show the highest specific discharge capacity of 377.5 mAhg(-1) at a current density of 50 mAg(-1) , and are better than the corresponding solid spheres and nanorod assemblies. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Triassico: A Sphere Positioning System for Surface Studies with IBA Techniques

NASA Astrophysics Data System (ADS)

Fontana, Cristiano L.; Doyle, Barney L.

We propose here a novel device, called the Triassico, to microscopically study the entire surface of millimeter-sized spheres. The sphere dimensions can be as small as 1 mm, and the upper limit defined only by the power and by the mechanical characteristics of the motors used. Three motorized driving rods are arranged so an equilateral triangle is formed by the rod's axes, on such a triangle the sphere sits. Movement is achieved by rotating the rods with precise relative speeds and by exploiting the friction between the sphere and the rods surfaces. The sphere can be held in place by gravity or by an opposing trio of rods. By rotating the rods with specific relative angular velocities, a net torque can be exerted on the sphere which then rotates. No repositioning of the sphere or of the motors is needed to cover the full surface with the investigating tools. An algorithm was developed to position the sphere at any arbitrary polar and azimuthal angle. The algorithm minimizes the number of rotations needed by the rods, in order to efficiently select a particular position on the sphere surface. A prototype Triassico was developed for the National Ignition Facility, of the Lawrence Livermore National Laboratory (Livermore, California, USA), as a sphere manipulation apparatus for ion microbeam analysis at Sandia National Laboratories (Albuquerque, NM, USA) of Xe-doped DT inertial confinement fusion fuel spheres. Other applications span from samples orientation, ball bearing manufacturing, or jewelry.

Maths Resource.

ERIC Educational Resources Information Center

Tapson, Frank

1985-01-01

Flow diagrams developing cube roots and formulas for the square, sphere, cube, circle and sector, oblong, and cylinder are presented. Some comments on their use, along with calculators, are included. (MNS)

Human rights and the Beijing Olympics: imagined global community and the transnational public sphere.

PubMed

Brownell, Susan

2012-06-01

The Olympic Games are increasingly used by non-governmental organizations to demand transnational forms of accountability from public authorities. This article assesses the effectiveness of transnational public opinion surrounding the Beijing 2008 Olympics, when the pressure of Western public opinion was exerted upon the government of the world's most populous non-Western nation to improve its human rights record. Utilizing the concepts of 'imagined global community' and 'transnational public sphere', it finds that the Olympic Games had helped to call into existence a transnational public that ran up against the obstacle posed by the incomplete formation of supra-national forms of governance. The International Olympic Committee, a non-governmental organization, was a weak substitute. Because of the strong desire of Chinese people to take part in transnational deliberations, the article concludes with optimism about the potential of transnational public spheres that include Chinese people to develop toward more effective forms of transnational governance. But the IOC must strengthen the voice of its non-Western members, and Western interlocutors, including the media, must accept their share of the responsibility for creating the conditions for egalitarian dialogue. © London School of Economics and Political Science 2012.

A numerical test of the topographic bias

NASA Astrophysics Data System (ADS)

Sjöberg, L. E.; Joud, M. S. S.

2018-02-01

In 1962 A. Bjerhammar introduced the method of analytical continuation in physical geodesy, implying that surface gravity anomalies are downward continued into the topographic masses down to an internal sphere (the Bjerhammar sphere). The method also includes analytical upward continuation of the potential to the surface of the Earth to obtain the quasigeoid. One can show that also the common remove-compute-restore technique for geoid determination includes an analytical continuation as long as the complete density distribution of the topography is not known. The analytical continuation implies that the downward continued gravity anomaly and/or potential are/is in error by the so-called topographic bias, which was postulated by a simple formula of L E Sjöberg in 2007. Here we will numerically test the postulated formula by comparing it with the bias obtained by analytical downward continuation of the external potential of a homogeneous ellipsoid to an inner sphere. The result shows that the postulated formula holds: At the equator of the ellipsoid, where the external potential is downward continued 21 km, the computed and postulated topographic biases agree to less than a millimetre (when the potential is scaled to the unit of metre).

Natural biopolymer-based nanocomposite films for packaging applications.

PubMed

Rhim, Jong-Whan; Ng, Perry K W

2007-01-01

Concerns on environmental waste problems caused by non-biodegradable petrochemical-based plastic packaging materials as well as the consumer's demand for high quality food products has caused an increasing interest in developing biodegradable packaging materials using annually renewable natural biopolymers such as polysaccharides and proteins. Inherent shortcomings of natural polymer-based packaging materials such as low mechanical properties and low water resistance can be recovered by applying a nanocomposite technology. Polymer nanocomposites, especially natural biopolymer-layered silicate nanocomposites, exhibit markedly improved packaging properties due to their nanometer size dispersion. These improvements include increased modulus and strength, decreased gas permeability, and increased water resistance. Additionally, biologically active ingredients can be added to impart the desired functional properties to the resulting packaging materials. Consequently, natural biopolymer-based nanocomposite packaging materials with bio-functional properties have a huge potential for application in the active food packaging industry. In this review, recent advances in the preparation of natural biopolymer-based films and their nanocomposites, and their potential use in packaging applications are addressed.

Porous Si spheres encapsulated in carbon shells with enhanced anodic performance in lithium-ion batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Hui; Wu, Ping, E-mail: zjuwuping@njnu.edu.cn; Shi, Huimin

2014-07-01

Highlights: • In situ magnesiothermic reduction route for the formation of porous Si@C spheres. • Unique microstructural characteristics of both porous sphere and carbon matrix. • Enhanced anodic performance in term of cycling stability for lithium-ion batteries. - Abstract: A novel type of porous Si–C micro/nano-hybrids, i.e., porous Si spheres encapsulated in carbon shells (porous Si@C spheres), has been constructed through the pyrolysis of polyvinylidene fluoride (PVDF) and subsequent magnesiothermic reduction methodology by using SiO{sub 2} spheres as precursors. The as-synthesized porous Si@C spheres have been applied as anode materials for lithium-ion batteries (LIBs), and exhibit enhanced anodic performance inmore » term of cycling stability compared with bare Si spheres. For example, the porous Si@C spheres are able to exhibit a high reversible capacity of 900.0 mA h g{sup −1} after 20 cycles at a current density of 0.05 C (1 C = 4200 mA g{sup −1}), which is much higher than that of bare Si spheres (430.7 mA h g{sup −1})« less

The NASA Electronic Parts and Packaging (NEPP) Program: Overview and Update FY15 and Beyond

NASA Technical Reports Server (NTRS)

LaBel, Kenneth A.; Sampson, Michael J.

2016-01-01

The NASA Electronic Parts and Packaging (NEPP) program, and its subset the NASA Electronic Parts Assurance Group (NEPAG), are NASA's point-of-contacts for reliability and radiation tolerance of electrical, electronic, and electromechanical (EEE) parts and their packages. This presentation includes a Fiscal Year 2015 program overview.

Applying Various Comprehension Strategies. Learning Package No. 8.

ERIC Educational Resources Information Center

Simic, Marge; Smith, Carl, Comp.

Originally developed for the Department of Defense Schools (DoDDS) system, this learning package on applying various comprehension strategies is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes a comprehensive search of the ERIC database; a lecture giving an overview on the topic; the…

Cultural Literacy. Learning Package No. 44.

ERIC Educational Resources Information Center

Hong, Zhang, Comp.; Smith, Carl, Ed.

Originally developed as part of a project for the Department of Defense Schools (DoDDS) system, this learning package on cultural literacy is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes an overview of the project; a comprehensive search of the ERIC database; a lecture giving an…

49 CFR 173.412 - Additional design requirements for Type A packages.

Code of Federal Regulations, 2010 CFR

2010-10-01

... materials within the temperature range. (d) The packaging must include a containment system securely closed... in accordance with § 173.469, may be considered as a component of the containment system. If the containment system forms a separate unit of the package, it must be securely closed by a positive fastening...

Journal Writing. Learning Package No. 34.

ERIC Educational Resources Information Center

Simic, Marge, Comp.; Smith, Carl, Ed.

Originally developed as part of a project for the Department of Defense Schools (DoDDS) system, this learning package on journal writing is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes an overview of the project; a comprehensive search of the ERIC database; a lecture giving an…

The Surgical Scrub. Learning Activity Package.

ERIC Educational Resources Information Center

Runge, Lillian

This learning activity package on the surgical scrub is one of a series of 12 titles developed for use in health occupations education programs. Materials in the package include objectives, a list of materials needed, a list of definitions, information sheets, reviews (self evaluations) of portions of the content, and answers to reviews. These…

15 CFR Appendix A to Part 946 - National Weather Service Modernization Criteria

Code of Federal Regulations, 2010 CFR

2010-01-01

... specifically in Addendum I, Appendix D of the ASOS Site Component Commissioning Evaluation Package (the ASOS Package). Criteria: a. ASOS Acceptance Test: The site component acceptance test, which includes objective..., has been successfully completed in accordance with item 1a, p. D-2 of Appendix D of the ASOS Package...

15 CFR Appendix A to Part 946 - National Weather Service Modernization Criteria

Code of Federal Regulations, 2013 CFR

2013-01-01

... specifically in Addendum I, Appendix D of the ASOS Site Component Commissioning Evaluation Package (the ASOS Package). Criteria: a. ASOS Acceptance Test: The site component acceptance test, which includes objective..., has been successfully completed in accordance with item 1a, p. D-2 of Appendix D of the ASOS Package...

15 CFR Appendix A to Part 946 - National Weather Service Modernization Criteria

Code of Federal Regulations, 2012 CFR

2012-01-01

... specifically in Addendum I, Appendix D of the ASOS Site Component Commissioning Evaluation Package (the ASOS Package). Criteria: a. ASOS Acceptance Test: The site component acceptance test, which includes objective..., has been successfully completed in accordance with item 1a, p. D-2 of Appendix D of the ASOS Package...

15 CFR Appendix A to Part 946 - National Weather Service Modernization Criteria

Code of Federal Regulations, 2011 CFR

2011-01-01

... specifically in Addendum I, Appendix D of the ASOS Site Component Commissioning Evaluation Package (the ASOS Package). Criteria: a. ASOS Acceptance Test: The site component acceptance test, which includes objective..., has been successfully completed in accordance with item 1a, p. D-2 of Appendix D of the ASOS Package...

21 CFR 801.40 - Form of a unique device identifier.

Code of Federal Regulations, 2014 CFR

2014-04-01

...) Automatic identification and data capture (AIDC) technology. (b) The UDI must include a device identifier... evident upon visual examination of the label or device package, the label or device package must disclose... label and device packages is deemed to meet all requirements of subpart B of this part. The UPC will...

How effective is the plain packaging of tobacco policy on rates of intention to quit smoking and changing attitudes to smoking?

PubMed

Lilic, Nick; Stretton, Matthew; Prakash, Minesh

2018-06-05

The aim of this study is to critically appraise the evidence for the effectiveness of the plain packaging of tobacco products policy. A systematic approach to a literature review was undertaken using five databases: PubMed, MEDLINE, Google Scholar, Global Health and Legacy Tobacco Documents Library. Quantitative and qualitative studies that evaluate attitudes towards smoking, starting smoking and quitting intentions when plain packaging use is compared with standard cigarette packaging use were included. A total of 1923 studies were identified. After inclusion and exclusion criteria were applied, nine studies were included in the review. The overall quality of the data was variable but a significant number of the studies had major methodological flaws. However, data analysed in the literature review suggest that exposure to plain packaging increases intention to quit amongst exposed individuals, increases negative attitudes to both smoking and starting smoking. Although the evidence for plain packaging of tobacco is not strong, the evidence that is available indicates that it is an effective tobacco cessation policy. © 2018 Royal Australasian College of Surgeons.

Computational study of the electronic structure and magnetic properties of the Ni-C state in [NiFe] hydrogenases including the second coordination sphere.

PubMed

Kampa, Mario; Lubitz, Wolfgang; van Gastel, Maurice; Neese, Frank

2012-12-01

[NiFe] hydrogenases catalyze the reversible formation of H(2). The [NiFe] heterobimetallic active site is rich in redox states. Here, we investigate the key catalytic state Ni-C of Desulfovibrio vulgaris Miyazaki F hydrogenase using a cluster model that includes the truncated amino acids of the entire second coordination sphere of the enzyme. The optimized geometries, computed g tensors, hyperfine coupling constants, and IR stretching frequencies all agree well with experimental values. For the hydride in the bridging position, only a single minimum on the potential energy surface is found, indicating that the hydride bridges and binds to both nickel and iron. The influence of the second coordination sphere on the electronic structure is investigated by comparing results from the large cluster models with truncated models. The largest interactions of the second coordination sphere with the active site concern the hydrogen bonds with the cyanide ligands, which modulate the bond between iron and these ligands. Secondly, the electronic structure of the active site is found to be sensitive to the protonation state of His88. This residue forms a hydrogen bond with the spin-carrying sulfur atom of Cys549, which in turn tunes the spin density at the nickel and coordinating sulfur atoms. In addition, the unequal distribution of spin density over the equatorial cysteine residues results from different orientations of the cysteine side chains, which are kept in their particular orientation by the secondary structure of the protein.

Effect of reductant and PVP on morphology and magnetic property of ultrafine Ni powders prepared via hydrothermal route

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Jun, E-mail: j-zhang@126.com; Wang, Xiucai; Li, Lili

2013-10-15

Graphical abstract: The ultrafine Ni powders with the shapes including sphere, pearl-string, leaf, fish-bone, hexagonal sheet and silknet were prepared through one-step hydrothermal reduction using different reductants. Their saturation magnetization, remanent magnetization and coercivity sequentially increase, and the coercivity of hexagonal sheet-like Ni powders increases by 25% compared with the Ni bulk counterpart. - Highlights: • The ultrafine Ni powders with various shapes of sphere, fish-bone, hexagonal sheet, etc. • Facile and one-step hydrothermal reduction using three reductants and PVP additive was developed. • Magnetic properties of the ultrafine Ni powders with different shapes were measured. • Compared with bulkmore » Ni material, coercivity of hexagonal sheet Ni increases by 25%. • The formation mechanism of the shapes was suggested. - Abstract: The ultrafine nickel particles with different shapes including sphere, pearl-string, leaf, fish-bone, hexagonal sheet and silknet were prepared through one-step hydrothermal reduction using hydrazine hydrate, sodium hypophosphite and ethylene glycol as reductants, polyvinylpyrrolidone as structure-directing agent. It has been verified with the characterization of X-ray powder diffraction and transmission/scanning electronic microscopy that as-prepared products belong to face-centered cubic structure of nickel microcrystals with high purity and fine dispersity. The magnetic hysteresis loops measured at room temperature reveal that the values of saturation magnetization, remanent magnetization and coercivity rise sequentially from silknet, sphere to hexagonal sheet. In comparison with nickel bulk counterpart, the coercivity of the hexagonal sheet nickel powders increases by 25%.« less

CSP Manufacturing Challenges and Assembly Reliability

NASA Technical Reports Server (NTRS)

Ghaffarian, Reza

2000-01-01

Although the expression of CSP is widely used by industry from suppliers to users, its implied definition had evolved as the technology has matured. There are "expert definition"- package that is up to 1.5 time die- or "interim definition". CSPs are miniature new packages that industry is starting to implement and there are many unresolved technical issues associated with their implementation. For example, in early 1997, packages with 1 mm pitch and lower were the dominant CSPs, whereas in early 1998 packages with 0.8 mm and lower became the norm for CSPs. Other changes included the use of flip chip die rather than wire bond in CSP. Nonetheless the emerging CSPs are competing with bare die assemblies and are becoming the package of choice for size reduction applications. These packages provide the benefits of small size and performance of the bare die or flip chip, with the advantage of standard die packages. The JPL-led MicrotypeBGA Consortium of enterprises representing government agencies and private companies have jointed together to pool in-kind resources for developing the quality and reliability of chip scale packages (CSPs) for a variety of projects. This talk will cover specifically the experience of our consortium on technology implementation challenges, including design and build of both standard and microvia boards, assembly of two types of test vehicles, and the most current environmental thermal cycling test results.

Performance of conduction cooled splittable superconducting magnet package for linear accelerators

DOE PAGES

Kashikhin, Vladimire S.; Andreev, N.; Cheban, S.; ...

2016-02-19

New Linear Superconducting Accelerators need a superconducting magnet package installed inside SCRF Cryomodules to focus and steer electron or proton beams. A superconducting magnet package was designed and built as a collaborative effort of FNAL and KEK. The magnet package includes one quadrupole, and two dipole windings. It has a splittable in the vertical plane configuration, and features for conduction cooling. The magnet was successfully tested at room temperature, in a liquid He bath, and in a conduction cooling experiment. The paper describes the design and test results including: magnet cooling, training, and magnetic measurements by rotational coils. Furthermore, themore » effects of superconductor and iron yoke magnetization, hysteresis, and fringe fields are discussed.« less

Comparison of NiS2 and α-NiS hollow spheres for supercapacitors, non-enzymatic glucose sensors and water treatment.

PubMed

Wei, Chengzhen; Cheng, Cheng; Cheng, Yanyan; Wang, Yan; Xu, Yazhou; Du, Weimin; Pang, Huan

2015-10-21

NiS2 hollow spheres are successfully prepared by a one-step template free method. Meanwhile, α-NiS hollow spheres can also be synthesized via the calcination of the pre-obtained NiS2 hollow spheres at 400 °C for 1 h in air. The electrochemical performances of the as-prepared NiS2 and α-NiS hollow sphere products are evaluated. When used for supercapacitors, compared with NiS2 hollow spheres, the α-NiS hollow sphere electrode shows a large specific capacitance of 717.3 F g(-1) at 0.6 A g(-1) and a good cycle life. Furthermore, NiS2 and α-NiS hollow spheres are successfully applied to fabricate non-enzymatic glucose sensors. In particular, the α-NiS hollow spheres exhibit good catalytic activity for the oxidation of glucose, a fast amperometric response time of less than 5 s, and the detection limit is estimated to be 0.08 μM. More importantly, compared with other normally co-existing interfering species, such as ascorbic acid, uric acid and dopamine, the electrode modified with α-NiS hollow spheres shows good selectivity. Moreover, the α-NiS hollow spheres also present good capacity to remove Congo red organic pollutants from wastewater by their surface adsorption ability.

Interaction of a shock wave with multiple spheres suspended in different arrangements

NASA Astrophysics Data System (ADS)

Zhang, Li-Te; Sui, Zhen-Zhen; Shi, Hong-Hui

2018-03-01

In this study, the unsteady drag force, Fd, drag coefficient, Cd, and the relevant dynamic behaviors of waves caused by the interaction between a planar incident shock wave and a multi-sphere model are investigated by using imbedded accelerometers and a high-speed Schlieren system. The shock wave is produced in a horizontal 200 mm inner diameter circular shock tube with a 2000 mm × 200 mm × 200 mm transparent test section. The time history of Cd is obtained based on band-block and low-pass Fast Fourier Transformation filtering combined with Savitzky-Golay polynomial smoothing for the measured acceleration. The effects of shock Mach number, Ms, geometry of multi-sphere model, nondimensional distance between sphere centers, H, and channel blockage are analyzed. We find that all time histories of Cd have a similar double-peak shaped main structure. It is due to wave reflection, diffraction, interference, and convergence at different positions of the spheres. The peak Fd increases, whereas the peak Cd decreases monotonically with increasing Ms. The increase of shock strength due to shock focusing by upstream spheres increases the peak Fd of downstream spheres. Both the increase in sphere number and the decrease in distance between spheres promote wave interference between neighboring spheres. As long as the wave interference times are shorter than the peak times, the peak Fd and Cd are higher compared to a single sphere.

WCPP-THE WOLF PLOTTING AND CONTOURING PACKAGE

NASA Technical Reports Server (NTRS)

Masaki, G. T.

1994-01-01

The WOLF Contouring and Plotting Package provides the user with a complete general purpose plotting and contouring capability. This package is a complete system for producing line printer, SC4020, Gerber, Calcomp, and SD4060 plots. The package has been designed to be highly flexible and easy to use. Any plot from a quick simple plot (which requires only one call to the package) to highly sophisticated plots (including motion picture plots) can be easily generated with only a basic knowledge of FORTRAN and the plot commands. Anyone designing a software system that requires plotted output will find that this package offers many advantages over the standard hardware support packages available. The WCPP package is divided into a plot segment and a contour segment. The plot segment can produce output for any combination of line printer, SC4020, Gerber, Calcomp, and SD4060 plots. The line printer plots allow the user to have plots available immediately after a job is run at a low cost. Although the resolution of line printer plots is low, the quick results allows the user to judge if a high resolution plot of a particular run is desirable. The SC4020 and SD4060 provide high speed high resolution cathode ray plots with film and hard copy output available. The Gerber and Calcomp plotters provide very high quality (of publishable quality) plots of good resolution. Being bed or drum type plotters, the Gerber and Calcomp plotters are usually slow and not suited for large volume plotting. All output for any or all of the plotters can be produced simultaneously. The types of plots supported are: linear, semi-log, log-log, polar, tabular data using the FORTRAN WRITE statement, 3-D perspective linear, and affine transformations. The labeling facility provides for horizontal labels, vertical labels, diagonal labels, vector characters of a requested size (special character fonts are easily implemented), and rotated letters. The gridding routines label the grid lines according to user specification. Special line features include multiple lines, dashed lines, and tic marks. The contour segment of this package is a collection of subroutines which can be used to produce contour plots and perform related functions. The package can contour any data which can be placed on a grid or data which is regularly spaced, including any general affine or polar grid data. The package includes routines which will grid random data. Contour levels can be specified at any values desired. Input data can be smoothed with undefined points being acceptable where data is unreliable or unknown. Plots which are extremely large or detailed can be automatically output in parts to improve resolution or overcome plotter size limitations. The contouring segment uses the plot segment for actual plotting, thus all the features described for the plotting segment are available to the user of the contouring segment. Included with this package are two data bases for producing world map plots in Mercator projection. One data base provides just continent outlines and another provides continent outlines and national borders in great detail. This package is written in FORTRAN IV and IBM OS ASSEMBLER and has been implemented on an IBM 360 with a central memory requirement of approximately 140K of 8 bit bytes. The ASSEMBLER routines are basic plotter interface routines. The WCPP package was developed in 1972.

Identification of tumor-initiating cells derived from two canine rhabdomyosarcoma cell lines

PubMed Central

KISHIMOTO, Takuya Evan; YASHIMA, Shoko; NAKAHIRA, Rei; ONOZAWA, Eri; AZAKAMI, Daigo; UJIKE, Makoto; OCHIAI, Kazuhiko; ISHIWATA, Toshiyuki; TAKAHASHI, Kimimasa; MICHISHITA, Masaki

2017-01-01

Cancer stem cells or tumor-initiating cells (TICs) are a small subpopulation of cells that have the capacity to self-renew, differentiate and initiate tumors. These cells may function in tumor initiation, aggression and recurrence. Whether spheres derived from canine rhabdomyosarcoma cells have stem cell-like properties is unclear. We induced sphere formation in the canine rhabdomyosarcoma cell lines, CMS-C and CMS-J, and characterized the spheres in vitro and in vivo. Sphere-forming cells were more resistant to vincristine, mitoxantrone and doxorubicin than adherent cells. Xenograft transplantation demonstrated that 1 × 103 sphere-forming cells derived from CMS-C were sufficient for tumor formation. The sphere assay showed that the sphere-forming cells were present in these tumors. These results suggest that the spheres derived from canine rhabdomyosarcoma cells may possess characteristics of TICs. This study provides the foundation for elucidating the contribution of TICs to rhabdomyosarcoma tumorigenesis. PMID:28529244

Identification of tumor-initiating cells derived from two canine rhabdomyosarcoma cell lines.

PubMed

Kishimoto, Takuya Evan; Yashima, Shoko; Nakahira, Rei; Onozawa, Eri; Azakami, Daigo; Ujike, Makoto; Ochiai, Kazuhiko; Ishiwata, Toshiyuki; Takahashi, Kimimasa; Michishita, Masaki

2017-07-07

Cancer stem cells or tumor-initiating cells (TICs) are a small subpopulation of cells that have the capacity to self-renew, differentiate and initiate tumors. These cells may function in tumor initiation, aggression and recurrence. Whether spheres derived from canine rhabdomyosarcoma cells have stem cell-like properties is unclear. We induced sphere formation in the canine rhabdomyosarcoma cell lines, CMS-C and CMS-J, and characterized the spheres in vitro and in vivo. Sphere-forming cells were more resistant to vincristine, mitoxantrone and doxorubicin than adherent cells. Xenograft transplantation demonstrated that 1 × 10 3 sphere-forming cells derived from CMS-C were sufficient for tumor formation. The sphere assay showed that the sphere-forming cells were present in these tumors. These results suggest that the spheres derived from canine rhabdomyosarcoma cells may possess characteristics of TICs. This study provides the foundation for elucidating the contribution of TICs to rhabdomyosarcoma tumorigenesis.

Specific surface area of overlapping spheres in the presence of obstructions

NASA Astrophysics Data System (ADS)

Jenkins, D. R.

2013-02-01

This study considers the random placement of uniform sized spheres, which may overlap, in the presence of another set of randomly placed (hard) spheres, which do not overlap. The overlapping spheres do not intersect the hard spheres. It is shown that the specific surface area of the collection of overlapping spheres is affected by the hard spheres, such that there is a minimum in the specific surface area as a function of the relative size of the two sets of spheres. The occurrence of the minimum is explained in terms of the break-up of pore connectivity. The configuration can be considered to be a simple model of the structure of a porous composite material. In particular, the overlapping particles represent voids while the hard particles represent fillers. Example materials are pervious concrete, metallurgical coke, ice cream, and polymer composites. We also show how the material properties of such composites are affected by the void structure.

Specific surface area of overlapping spheres in the presence of obstructions.

PubMed

Jenkins, D R

2013-02-21

This study considers the random placement of uniform sized spheres, which may overlap, in the presence of another set of randomly placed (hard) spheres, which do not overlap. The overlapping spheres do not intersect the hard spheres. It is shown that the specific surface area of the collection of overlapping spheres is affected by the hard spheres, such that there is a minimum in the specific surface area as a function of the relative size of the two sets of spheres. The occurrence of the minimum is explained in terms of the break-up of pore connectivity. The configuration can be considered to be a simple model of the structure of a porous composite material. In particular, the overlapping particles represent voids while the hard particles represent fillers. Example materials are pervious concrete, metallurgical coke, ice cream, and polymer composites. We also show how the material properties of such composites are affected by the void structure.

Generating perfect fluid spheres in general relativity

NASA Astrophysics Data System (ADS)

Boonserm, Petarpa; Visser, Matt; Weinfurtner, Silke

2005-06-01

Ever since Karl Schwarzschild’s 1916 discovery of the spacetime geometry describing the interior of a particular idealized general relativistic star—a static spherically symmetric blob of fluid with position-independent density—the general relativity community has continued to devote considerable time and energy to understanding the general-relativistic static perfect fluid sphere. Over the last 90 years a tangle of specific perfect fluid spheres has been discovered, with most of these specific examples seemingly independent from each other. To bring some order to this collection, in this article we develop several new transformation theorems that map perfect fluid spheres into perfect fluid spheres. These transformation theorems sometimes lead to unexpected connections between previously known perfect fluid spheres, sometimes lead to new previously unknown perfect fluid spheres, and in general can be used to develop a systematic way of classifying the set of all perfect fluid spheres.

In vitro and in vivo study of the application of volvox spheres to co-culture vehicles in liver tissue engineering.

PubMed

Chang, Siou Han; Huang, Han Hsiang; Kang, Pei Leun; Wu, Yu Chian; Chang, Ming-Huang; Kuo, Shyh Ming

2017-11-01

Volvox sphere is a biomimetic concept of a natural Volvox, wherein a large outer sphere contains smaller inner spheres, which can encapsulate cells and provide a double-layer three-dimensional environment for culturing cells. This study simultaneously encapsulated rat mesenchymal stem cells (MSCs) and AML12 hepatocytes in volvox spheres and extensively evaluated the effects of various culturing modes on cell functions and fates. The results showed that compared with a static flask culture, MSCs encapsulated in volvox spheres differentiated into hepatocyte-like cells with a 2-fold increase in albumin (ALB) expression and a 2.5-fold increase in cytokeratin 18 expression in a dynamic bioreactor. Moreover, the restorative effects of volvox spheres encapsulating cells on retrorsine-exposed CCl 4 -induced liver injuries in rats were evaluated. The data presented significant reductions in AST and ALT levels after the implantation of volvox spheres encapsulating both MSCs and AML12 hepatocytes in vivo. In contrast to the negative control group, histopathological analysis demonstrated liver repair and formation of the new liver tissue in groups implanted with volvox spheres containing cells. These results demonstrate that liver cells implanted with volvox spheres encapsulating both MSCs and AML12 hepatocytes promote liver repair and liver tissue regeneration in liver failure caused by necrotizing agents such as retrorsine and CCl 4 . Hence, volvox spheres encapsulating MSCs and liver cells can be a promising and clinically effective therapy for liver injury. In this study, we used a volvox sphere, which is a unique design that mimics the natural Volvox, that consists of a large outer sphere that contains smaller inner spheres, which provide a three-dimensional environment to culture cells. The purpose of this study is to co-culture mesenchymal stem cells (MSCs) and AML12 liver cells in volvox spheres and evaluate two different culture methods, dynamic bioreactor and static culture flask,on the cultured cells. In addition, we aimed to evaluate the restorative effects of volvox spheres encapsulating MSCs and/or AML12 liver cells on rats with retrorsine-exposed CCl 4 -induced liver injuries. The results showed that MSCs encapsulated in volvox spheres differentiated into hepatocyte-like cells with a 2-fold increase in albumin expression and a 2.5-fold increase in cytokeratin 18 expression ina dynamic bioreactor. Moreover, the data presented significant reductions in AST and ALT levels after the implantation of volvox spheres encapsulating both MSCs and AML12 hepatocytes in vivo. In contrast to the negative control group, histopathological analysis demonstrated liver repair and formation of new liver tissue in groups implanted with volvox spheres containing cells. These results demonstrate that liver cells implanted with volvox spheres encapsulating both MSCs and AML12 hepatocytes promote liver repair and liver tissue regeneration in liver failure caused by necrotizing agents such as retrorsine and CCl 4 . Hence, volvox spheres encapsulating MSCs and liver cells can be a promising and clinically effective therapy for liver injury. Copyright © 2017 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Recent advances in photonics packaging materials

NASA Astrophysics Data System (ADS)

Zweben, Carl

2006-02-01

There are now over a dozen low-CTE materials with thermal conductivities between that of copper (400 w/m-K) and over 4X copper (1700 W/m-K). Most have low densities. For comparison, traditional low-CTE packaging materials like copper/tungsten have thermal conductivities that are little or no better than that of aluminum (200 W/m-K) and high densities. There are also low-density thermal insulators with low CTEs. Some advanced materials are low cost. Most do not outgas. They have a wide range of electrical properties that can be used to minimize electromagnetic emissions or provide EMI shielding. Several are now in commercial and aerospace applications, including laser diode packages; light-emitting diode (LED) packages; thermoelectric cooler bases, plasma displays; power modules; servers; laptops; heat sinks; thermally conductive, low-CTE printed circuit boards; and printed circuit board cold plates. Advanced material payoffs include: improved thermal performance, reliability, alignment and manufacturing yield; reduced thermal stresses and heating power requirements; simplified thermal design; enablement of hard solder direct attach; weight savings up to 85%; size reductions up to 65%; and lower cost. This paper discusses the large and increasing number of advanced packaging materials, including properties, development status, applications, increasing manufacturing yield, cost, lessons learned and future directions, including nanocomposites.

GneimoSim: A Modular Internal Coordinates Molecular Dynamics Simulation Package

PubMed Central

Larsen, Adrien B.; Wagner, Jeffrey R.; Kandel, Saugat; Salomon-Ferrer, Romelia; Vaidehi, Nagarajan; Jain, Abhinandan

2014-01-01

The Generalized Newton Euler Inverse Mass Operator (GNEIMO) method is an advanced method for internal coordinates molecular dynamics (ICMD). GNEIMO includes several theoretical and algorithmic advancements that address longstanding challenges with ICMD simulations. In this paper we describe the GneimoSim ICMD software package that implements the GNEIMO method. We believe that GneimoSim is the first software package to include advanced features such as the equipartition principle derived for internal coordinates, and a method for including the Fixman potential to eliminate systematic statistical biases introduced by the use of hard constraints. Moreover, by design, GneimoSim is extensible and can be easily interfaced with third party force field packages for ICMD simulations. Currently, GneimoSim includes interfaces to LAMMPS, OpenMM, Rosetta force field calculation packages. The availability of a comprehensive Python interface to the underlying C++ classes and their methods provides a powerful and versatile mechanism for users to develop simulation scripts to configure the simulation and control the simulation flow. GneimoSim has been used extensively for studying the dynamics of protein structures, refinement of protein homology models, and for simulating large scale protein conformational changes with enhanced sampling methods. GneimoSim is not limited to proteins and can also be used for the simulation of polymeric materials. PMID:25263538

GneimoSim: a modular internal coordinates molecular dynamics simulation package.

PubMed

Larsen, Adrien B; Wagner, Jeffrey R; Kandel, Saugat; Salomon-Ferrer, Romelia; Vaidehi, Nagarajan; Jain, Abhinandan

2014-12-05

The generalized Newton-Euler inverse mass operator (GNEIMO) method is an advanced method for internal coordinates molecular dynamics (ICMD). GNEIMO includes several theoretical and algorithmic advancements that address longstanding challenges with ICMD simulations. In this article, we describe the GneimoSim ICMD software package that implements the GNEIMO method. We believe that GneimoSim is the first software package to include advanced features such as the equipartition principle derived for internal coordinates, and a method for including the Fixman potential to eliminate systematic statistical biases introduced by the use of hard constraints. Moreover, by design, GneimoSim is extensible and can be easily interfaced with third party force field packages for ICMD simulations. Currently, GneimoSim includes interfaces to LAMMPS, OpenMM, and Rosetta force field calculation packages. The availability of a comprehensive Python interface to the underlying C++ classes and their methods provides a powerful and versatile mechanism for users to develop simulation scripts to configure the simulation and control the simulation flow. GneimoSim has been used extensively for studying the dynamics of protein structures, refinement of protein homology models, and for simulating large scale protein conformational changes with enhanced sampling methods. GneimoSim is not limited to proteins and can also be used for the simulation of polymeric materials. © 2014 Wiley Periodicals, Inc.

Re-design of apple pia packaging using quality function deployment method

NASA Astrophysics Data System (ADS)

Pulungan, M. H.; Nadira, N.; Dewi, I. A.

2018-03-01

This study was aimed to identify the attributes for premium apple pia packaging, to determine the technical response to be carried out by Permata Agro Mandiri Small and Medium Enterprise (SME) and to design a new apple pie packaging acceptable by the SME. The Quality Function Deployment (QFD) method was employed to improve the apple pia packaging design, which consisted of seven stages in data analysis. The results indicated that whats attribute required by the costumers include graphic design, dimensions, capacity, shape, strength, and resistance of packaging. While, the technical responses to be conducted by the SMEs were as follows: attractive visual packaging designs, attractive colors, clear images and information, packaging size dimensions, a larger capacity packaging (more product content), ergonomic premium packaging, not easily torn, and impact resistant packaging materials. The findings further confirmed that the design of premium apple pia packaging accepted by the SMES was the one with the capacity of ten apple pia or 200 g weight, and with rectangular or beam shape form. The packaging material used was a duplex carton with 400 grammage (g/m2), the outer part of the packaging was coated with plastic and the inside was added with duplex carton. The acceptable packaging dimension was 30 cm x 5 cm x 3 cm (L x W x H) with a mix of black and yellow color in the graphical design.

Tobacco packaging design for reducing tobacco use.

PubMed

McNeill, Ann; Gravely, Shannon; Hitchman, Sara C; Bauld, Linda; Hammond, David; Hartmann-Boyce, Jamie

2017-04-27

Tobacco use is the largest single preventable cause of death and disease worldwide. Standardised tobacco packaging is an intervention intended to reduce the promotional appeal of packs and can be defined as packaging with a uniform colour (and in some cases shape and size) with no logos or branding, apart from health warnings and other government-mandated information, and the brand name in a prescribed uniform font, colour and size. Australia was the first country to implement standardised tobacco packaging between October and December 2012, France implemented standardised tobacco packaging on 1 January 2017 and several other countries are implementing, or intending to implement, standardised tobacco packaging. To assess the effect of standardised tobacco packaging on tobacco use uptake, cessation and reduction. We searched MEDLINE, Embase, PsycINFO and six other databases from 1980 to January 2016. We checked bibliographies and contacted study authors to identify additional peer-reviewed studies. Primary outcomes included changes in tobacco use prevalence incorporating tobacco use uptake, cessation, consumption and relapse prevention. Secondary outcomes covered intermediate outcomes that can be measured and are relevant to tobacco use uptake, cessation or reduction. We considered multiple study designs: randomised controlled trials, quasi-experimental and experimental studies, observational cross-sectional and cohort studies. The review focused on all populations and people of any age; to be included, studies had to be published in peer-reviewed journals. We examined studies that assessed the impact of changes in tobacco packaging such as colour, design, size and type of health warnings on the packs in relation to branded packaging. In experiments, the control condition was branded tobacco packaging but could include variations of standardised packaging. Screening and data extraction followed standard Cochrane methods. We used different 'Risk of bias' domains for different study types. We have summarised findings narratively. Fifty-one studies met our inclusion criteria, involving approximately 800,000 participants. The studies included were diverse, including observational studies, between- and within-participant experimental studies, cohort and cross-sectional studies, and time-series analyses. Few studies assessed behavioural outcomes in youth and non-smokers. Five studies assessed the primary outcomes: one observational study assessed smoking prevalence among 700,000 participants until one year after standardised packaging in Australia; four studies assessed consumption in 9394 participants, including a series of Australian national cross-sectional surveys of 8811 current smokers, in addition to three smaller studies. No studies assessed uptake, cessation, or relapse prevention. Two studies assessed quit attempts. Twenty studies examined other behavioural outcomes and 45 studies examined non-behavioural outcomes (e.g. appeal, perceptions of harm). In line with the challenges inherent in evaluating standardised tobacco packaging, a number of methodological imitations were apparent in the included studies and overall we judged most studies to be at high or unclear risk of bias in at least one domain. The one included study assessing the impact of standardised tobacco packaging on smoking prevalence in Australia found a 3.7% reduction in odds when comparing before to after the packaging change, or a 0.5 percentage point drop in smoking prevalence, when adjusting for confounders. Confidence in this finding is limited, due to the nature of the evidence available, and is therefore rated low by GRADE standards. Findings were mixed amongst the four studies assessing consumption, with some studies finding no difference and some studies finding evidence of a decrease; certainty in this outcome was rated very low by GRADE standards due to the limitations in study design. One national study of Australian adult smoker cohorts (5441 participants) found that quit attempts increased from 20.2% prior to the introduction of standardised packaging to 26.6% one year post-implementation. A second study of calls to quitlines provides indirect support for this finding, with a 78% increase observed in the number of calls after the implementation of standardised packaging. Here again, certainty is low. Studies of other behavioural outcomes found evidence of increased avoidance behaviours when using standardised packs, reduced demand for standardised packs and reduced craving. Evidence from studies measuring eye-tracking showed increased visual attention to health warnings on standardised compared to branded packs. Corroborative evidence for the latter finding came from studies assessing non-behavioural outcomes, which in general found greater warning salience when viewing standardised, than branded packs. There was mixed evidence for quitting cognitions, whereas findings with youth generally pointed towards standardised packs being less likely to motivate smoking initiation than branded packs. We found the most consistent evidence for appeal, with standardised packs rating lower than branded packs. Tobacco in standardised packs was also generally perceived as worse-tasting and lower quality than tobacco in branded packs. Standardised packaging also appeared to reduce misperceptions that some cigarettes are less harmful than others, but only when dark colours were used for the uniform colour of the pack. The available evidence suggests that standardised packaging may reduce smoking prevalence. Only one country had implemented standardised packaging at the time of this review, so evidence comes from one large observational study that provides evidence for this effect. A reduction in smoking behaviour is supported by routinely collected data by the Australian government. Data on the effects of standardised packaging on non-behavioural outcomes (e.g. appeal) are clearer and provide plausible mechanisms of effect consistent with the observed decline in prevalence. As standardised packaging is implemented in different countries, research programmes should be initiated to capture long term effects on tobacco use prevalence, behaviour, and uptake. We did not find any evidence suggesting standardised packaging may increase tobacco use.

The comparison of antimicrobial packaging properties with different applications incorporation method of active material

NASA Astrophysics Data System (ADS)

Anwar, R. W.; Sugiarto; Warsiki, E.

2018-03-01

Contamination after the processing of products during storage, distribution and marketing is one of the main causes of food safety issues. Handling of food products after processing can be done during the packaging process. Antimicrobial (AM) active packaging is one of the concept of packaging product development by utilize the interaction between the product and the packaging environment that can delay the bacterial damage by killing or reducing bacterial growth. The active system is formed by incorporating an antimicrobial agent against a packaging matrix that will function as a carrier. Many incorporation methods have been developed in this packaging-making concept which were direct mixing, polishing, and encapsulation. The aims of this research were to examine the different of the AM packaging performances including its stability and effectiveness of its function that would be produced by three different methods. The stability of the packaging function was analyzed by looking at the diffusivity of the active ingredient to the matrix using SEM. The effectiveness was analyzed by the ability of the packaging to prevent the growing of the microbial. The results showed that different incorporation methods resulted on different characteristics of the AM packaging.

Development of low cost, high reliability sealing techniques for hybrid microcircuit packages. Phase 2, supplement 1: Moisture permeation of adhesive-sealed hybrid microcircuit packages

NASA Technical Reports Server (NTRS)

Perkins, K. L.; Licari, J. J.

1978-01-01

The susceptibility of adhesive-sealed ceramic packages to moisture permeation was investigated. The two adhesives, Ablebond 789-1 and Epo-Tek H77, were evaluated as package sealants. These adhesives were previously selected as the most promising candidates for this application from a group of ten adhesives. Ceramic packages sealed with these adhesives were exposed to temperature-humidity conditions of 25 C/98 percent RH, 50 C/60 percent RH, 50 C/98 percent RH, and 85 C/85 percent RH and their moisture contents using were monitored solid state moisture sensors sealed inside them. Five packages were tested at each of these exposures - two ceramic packages sealed with each of the two adhesives and one seam-sealed gold-plated Kovar package. This latter package was included to serve as a control. The results showed that the adhesive-sealed packages were not hermetic to moisture. The rates at which moisture entered the packages increased with the severity of the exposure environments (i.e., higher temperatures and higher moisture vapor pressures) with greater dependence on temperature than on moisture vapor pressure.

Essential interventions: implementation strategies and proposed packages of care

PubMed Central

2014-01-01

In an effort to accelerate progress towards achieving Millennium Development Goal (MDG) 4 and 5, provision of essential reproductive, maternal, newborn and child health (RMNCH) interventions is being considered. Not only should a state-of-the-art approach be taken for services delivered to the mother, neonate and to the child, but services must also be deployed across the household to hospital continuum of care approach and in the form of packages. The paper proposed several packages for improved maternal, newborn and child health that can be delivered across RMNCH continuum of care. These packages include: supportive care package for women to promote awareness related to healthy pre-pregnancy and pregnancy interventions; nutritional support package for mother to improve supplementation of essential nutrients and micronutrients; antenatal care package to detect, treat and manage infectious and noninfectious diseases and promote immunization; high risk care package to manage preeclampsia and eclampsia in pregnancy; childbirth package to promote support during labor and importance of skilled birth attendance during labor; essential newborn care package to support healthy newborn care practices; and child health care package to prevent and manage infections. This paper further discussed the implementation strategies for employing these interventions at scale. PMID:25178110

Healthy choice?: Exploring how children evaluate the healthfulness of packaged foods.

PubMed

Elliott, Charlene; Brierley, Meaghan

2012-11-06

Today's supermarket contains hundreds of packaged foods specifically targeted at children. Yet research has shown that children are confused by the various visual messages found on packaged food products. This study explores children's nutrition knowledge with regard to packaged food products, to uncover strengths and difficulties they have in evaluating the healthfulness of these foods. Focus groups were conducted with children (grades 1-6). Particular attention was paid to the ways children made use of what they know about nutrition when faced with the visual elements and appeals presented on food packaging. Children relied heavily on packages' written and visual aspects--including colour, images, spokes-characters, front-of-package claims--to assess the healthfulness of a food product. These elements interfere with children's ability to make healthy choices when it comes to packaged foods. Choosing healthy packaged foods is challenging for children due to competing sets of knowledge: one pertains to their understanding of visual, associational cues; the other, to translating their understanding of nutrition to packaged foods. Canada's Food Guide, along with the curriculum taught to Canadian children at schools, does not appear to provide children with the tools necessary to navigate a food environment dominated by packaged foods.

Sphericity determination using resonant ultrasound spectroscopy

DOEpatents

Dixon, Raymond D.; Migliori, Albert; Visscher, William M.

1994-01-01

A method is provided for grading production quantities of spherical objects, such as roller balls for bearings. A resonant ultrasound spectrum (RUS) is generated for each spherical object and a set of degenerate sphere-resonance frequencies is identified. From the degenerate sphere-resonance frequencies and known relationships between degenerate sphere-resonance frequencies and Poisson's ratio, a Poisson's ratio can be determined, along with a "best" spherical diameter, to form spherical parameters for the sphere. From the RUS, fine-structure resonant frequency spectra are identified for each degenerate sphere-resonance frequency previously selected. From each fine-structure spectrum and associated sphere parameter values an asphericity value is determined. The asphericity value can then be compared with predetermined values to provide a measure for accepting or rejecting the sphere.

Sphericity determination using resonant ultrasound spectroscopy

DOEpatents

Dixon, R.D.; Migliori, A.; Visscher, W.M.

1994-10-18

A method is provided for grading production quantities of spherical objects, such as roller balls for bearings. A resonant ultrasound spectrum (RUS) is generated for each spherical object and a set of degenerate sphere-resonance frequencies is identified. From the degenerate sphere-resonance frequencies and known relationships between degenerate sphere-resonance frequencies and Poisson's ratio, a Poisson's ratio can be determined, along with a 'best' spherical diameter, to form spherical parameters for the sphere. From the RUS, fine-structure resonant frequency spectra are identified for each degenerate sphere-resonance frequency previously selected. From each fine-structure spectrum and associated sphere parameter values an asphericity value is determined. The asphericity value can then be compared with predetermined values to provide a measure for accepting or rejecting the sphere. 14 figs.

Destructive examination of shipping package 9975-02101

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daugherty, W. L.

Destructive and non-destructive examinations have been performed on the components of shipping package 9975-02101 as part of the comprehensive Model 9975 package surveillance program. This package is one of ten high-wattage packages that were selected for field surveillance in FY15, and was identified to contain several non-conforming conditions. Most of these conditions (mold, stains, drum corrosion, calculated fiberboard dimensions and fiberboard damage) relate to the accumulation of water in the outer and lower portions of the cane fiberboard assembly. In the short term, this causes local but reversible changes in the fiberboard properties. Long-term effects can include the permanent lossmore » of fiberboard properties (thus far observed only in the bottom fiberboard layers) and reduced drum integrity due to corrosion. The observed conditions must be fully evaluated by KAC to ensure the safety function of the package is being maintained. Three of the other nine FY15 high-wattage packages examined in the K-Area Complex showed similar behavior. Corrosion of the overpack drum has been seen primarily in those packages with relatively severe fiberboard degradation. Visual examination of the drums in storage for external corrosion should be considered as a screening tool to identify additional packages with potential fiberboard degradation. Where overpack drum corrosion has been observed, it is typically heaviest adjacent to the stitch welds along the bottom edge. It is possible that changes to the stitch weld design would reduce the degree of corrosion in this area, but would not eliminate it. Several factors can contribute to the concentration of moisture in the fiberboard, including higher than average initial moisture content, higher internal temperature (due to internal heat load and placement with the array of packages), and the creation of additional moisture as the fiberboard begins to degrade.« less

Use of modified atmosphere packaging to preserve mushroom quality during storage.

PubMed

Palacios, Irene; Moro, Carlos; Lozano, Miguel; D'Arrigo, Matilde; Guillamón, Eva; García-Lafuente, Ana; Villares, Ana

2011-09-01

Mushrooms have attracted much attention due to their excellent nutritional and sensory properties. However, they are highly perishable and rapidly lose their organoleptic characteristics. Many methods have been employed for mushroom storage, such as packaging, blanching, canning, or freeze drying. Among them, modified atmosphere packaging (MAP) has been widely employed for preserving fresh mushrooms. MAP provides an affordable packaging system that partly avoids enzymatic browning, fermentation and other biochemical processes by maintaining a controlled gas atmosphere. Several factors, including optimum CO2 and O2 partial pressures, permeability, package material, thickness, or product weight, must be considered in order to design a suitable modified atmosphere package for mushrooms. Thus, different strategies are available to preserve mushroom quality after harvest. The article presents some promising patents on use of modified atmosphere packaging to preserve mushroom quality during storage.

Effects of a Treatment Package to Facilitate English/Language Arts Learning for Middle School Students with Moderate to Severe Disabilities

ERIC Educational Resources Information Center

Mims, Pamela J.; Lee, Angel; Browder, Diane M.; Zakas, Tracie-Lynn; Flynn, Susan

2012-01-01

This pilot study sought to develop and evaluate the use of a treatment package that included systematic and direct instruction on acquisition of literacy skills aligned with middle school English/Language Arts standards for students with moderate to severe disabilities, including autism. Participants included five teachers and 15 middle school…

Scientific Software: How to Find What You Need and Get What You Pay for.

ERIC Educational Resources Information Center

Gabaldon, Diana J.

1984-01-01

Provides examples of software for the sciences, including: packages for pathology/toxicology laboratories (costing over $15,000), DNA sequencing, and data acquisition/analysis; general-purpose software for scientific uses; and "custom" packages, including a program to maintain a listing of "Escherichia coli" strains and a…

Information Business: Applying Infometry (Informational Geometry) in Cognitive Coordination and Genetic Programming for Electronic Information Packaging and Marketing.

ERIC Educational Resources Information Center

Tsai, Bor-sheng

1994-01-01

Describes the use of infometry, or informational geometry, to meet the challenges of information service businesses. Highlights include theoretical models for cognitive coordination and genetic programming; electronic information packaging; marketing electronic information products, including cost-benefit analyses; and recapitalization, including…

40 CFR 156.146 - Residue removal instructions for nonrefillable containers-rigid containers with dilutable...

Code of Federal Regulations, 2010 CFR

2010-07-01

... product packaged in a rigid nonrefillable container must include the following residue removal... dilutable pesticide product packaged in rigid nonrefillable containers must include one of the following sets of instructions. (1) For liquid dilutable pesticide products in containers small enough to shake...

21 CFR 1305.21 - Requirements for electronic orders.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 1311 of this chapter. (b) The following data fields must be included on an electronic order for... either the purchaser or the supplier). (8) The quantity in a single package or container. (9) The number of packages or containers of each item ordered. (c) An electronic order may include controlled...

21 CFR 1305.21 - Requirements for electronic orders.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 1311 of this chapter. (b) The following data fields must be included on an electronic order for... either the purchaser or the supplier). (8) The quantity in a single package or container. (9) The number of packages or containers of each item ordered. (c) An electronic order may include controlled...

21 CFR 1305.21 - Requirements for electronic orders.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 1311 of this chapter. (b) The following data fields must be included on an electronic order for... either the purchaser or the supplier). (8) The quantity in a single package or container. (9) The number of packages or containers of each item ordered. (c) An electronic order may include controlled...

What is included with your online e-cigarette order? An analysis of e-cigarette shipping, product and packaging features.

PubMed

Kong, Amanda Y; Derrick, Jason C; Abrantes, Anthony S; Williams, Rebecca S

2016-06-29

The electronic cigarette industry is growing, with youth using e-cigarettes at higher rates than they are using cigarettes, and retail and online sales projected to reach $10 billion in 2017. Minimal regulation of the production and marketing of e-cigarettes exists to date, which has allowed companies to promote unsupported claims. We assessed the shipping, product features and packaging of a wide variety of e-cigarettes purchased online by adults and youth. The most popular internet e-cigarette vendors were identified from a larger study of internet tobacco vendors. Between August 2013 and June 2014, adults made 56 purchase attempts from online vendors, and youth made 98 attempts. Packages received were assessed for exterior and internal packaging features, including product information, health warnings and additional materials. We analysed a total of 125 orders featuring 86 unique brands of e-cigarettes. The contents were rarely indicated on package exteriors. Product information came with just 60% of orders and just 38.4% included an instruction manual. Only 44.6% of products included a health warning, and some had unsupported claims, such as lack of secondhand smoke exposure. Additionally, some products were leaking e-liquid and battery fluid on arrival. A large variety of e-cigarette products are manufactured and marketed to consumers. Many products do not include instructions for use, and unsupported claims are being presented to consumers. Effective federal regulation of the manufacturing, packaging, product information and health claims surrounding e-cigarettes is necessary to ensure consumers are presented with accurate e-cigarette use information. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

What is included with your online e-cigarette order? An analysis of e-cigarette shipping, product and packaging features

PubMed Central

Kong, Amanda Y; Derrick, Jason C; Abrantes, Anthony S

2016-01-01

Background The electronic cigarette industry is growing, with youth using e-cigarettes at higher rates than they are using cigarettes, and retail and online sales projected to reach $10 billion in 2017. Minimal regulation of the production and marketing of e-cigarettes exists to date, which has allowed companies to promote unsupported claims. We assessed the shipping, product features and packaging of a wide variety of e-cigarettes purchased online by adults and youth. Methods The most popular internet e-cigarette vendors were identified from a larger study of internet tobacco vendors. Between August 2013 and June 2014, adults made 56 purchase attempts from online vendors, and youth made 98 attempts. Packages received were assessed for exterior and internal packaging features, including product information, health warnings and additional materials. Results We analysed a total of 125 orders featuring 86 unique brands of e-cigarettes. The contents were rarely indicated on package exteriors. Product information came with just 60% of orders and just 38.4% included an instruction manual. Only 44.6% of products included a health warning, and some had unsupported claims, such as lack of secondhand smoke exposure. Additionally, some products were leaking e-liquid and battery fluid on arrival. Conclusions A large variety of e-cigarette products are manufactured and marketed to consumers. Many products do not include instructions for use, and unsupported claims are being presented to consumers. Effective federal regulation of the manufacturing, packaging, product information and health claims surrounding e-cigarettes is necessary to ensure consumers are presented with accurate e-cigarette use information. PMID:27357936

77 FR 67678 - Content Specifications and Shielding Evaluations for Type B Transportation Packages

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-13

...The U.S. Nuclear Regulatory Commission (NRC or the Commission) is issuing for public comment Draft Regulatory Issue Summary (RIS) 2012-XX, ``Content Specifications and Shielding Evaluations for Type B Transportation Packages.'' This RIS clarifies the NRC's use of staff guidance in NUREG-1609, ``Standard Review Plan for Transport Packages for Radioactive Material,'' for the review of content specifications and shielding evaluations included in the Certificates of Compliance (CoC) and safety analysis reports (SARs) for Type B transportation packages.

Advanced Manufacturing Systems in Food Processing and Packaging Industry

NASA Astrophysics Data System (ADS)

Shafie Sani, Mohd; Aziz, Faieza Abdul

2013-06-01

In this paper, several advanced manufacturing systems in food processing and packaging industry are reviewed, including: biodegradable smart packaging and Nano composites, advanced automation control system consists of fieldbus technology, distributed control system and food safety inspection features. The main purpose of current technology in food processing and packaging industry is discussed due to major concern on efficiency of the plant process, productivity, quality, as well as safety. These application were chosen because they are robust, flexible, reconfigurable, preserve the quality of the food, and efficient.

Design requirements for SRB production control system. Volume 3: Package evaluation, modification and hardware

NASA Technical Reports Server (NTRS)

1981-01-01

The software package evaluation was designed to analyze commercially available, field-proven, production control or manufacturing resource planning management technology and software package. The analysis was conducted by comparing SRB production control software requirements and conceptual system design to software package capabilities. The methodology of evaluation and the findings at each stage of evaluation are described. Topics covered include: vendor listing; request for information (RFI) document; RFI response rate and quality; RFI evaluation process; and capabilities versus requirements.

Image dissector control and data system, part 1. [instrument packages and equipment specifications

NASA Technical Reports Server (NTRS)

1974-01-01

A general description of the image dissector control and data system is presented along with detailed design information, operating instructions, and maintenance and trouble-shooting procedures for the four instrumentation packages. The four instrumentation packages include a 90 inch telescope, a simplified telescope module for use on the 90 inch or other telescopes, a photographic plate scanner module which permits the scanning of astronomical photographic plates in the laboratory, and the lunar experiment package module.

ARM Data-Oriented Metrics and Diagnostics Package for Climate Model Evaluation Value-Added Product

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Chengzhu; Xie, Shaocheng

A Python-based metrics and diagnostics package is currently being developed by the U.S. Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) Infrastructure Team at Lawrence Livermore National Laboratory (LLNL) to facilitate the use of long-term, high-frequency measurements from the ARM Facility in evaluating the regional climate simulation of clouds, radiation, and precipitation. This metrics and diagnostics package computes climatological means of targeted climate model simulation and generates tables and plots for comparing the model simulation with ARM observational data. The Coupled Model Intercomparison Project (CMIP) model data sets are also included in the package to enable model intercomparison as demonstratedmore » in Zhang et al. (2017). The mean of the CMIP model can serve as a reference for individual models. Basic performance metrics are computed to measure the accuracy of mean state and variability of climate models. The evaluated physical quantities include cloud fraction, temperature, relative humidity, cloud liquid water path, total column water vapor, precipitation, sensible and latent heat fluxes, and radiative fluxes, with plan to extend to more fields, such as aerosol and microphysics properties. Process-oriented diagnostics focusing on individual cloud- and precipitation-related phenomena are also being developed for the evaluation and development of specific model physical parameterizations. The version 1.0 package is designed based on data collected at ARM’s Southern Great Plains (SGP) Research Facility, with the plan to extend to other ARM sites. The metrics and diagnostics package is currently built upon standard Python libraries and additional Python packages developed by DOE (such as CDMS and CDAT). The ARM metrics and diagnostic package is available publicly with the hope that it can serve as an easy entry point for climate modelers to compare their models with ARM data. In this report, we first present the input data, which constitutes the core content of the metrics and diagnostics package in section 2, and a user's guide documenting the workflow/structure of the version 1.0 codes, and including step-by-step instruction for running the package in section 3.« less

Botulism challenge studies of a modified atmosphere package for fresh mussels: inoculated pack studies.

PubMed

Newell, C R; Ma, Li; Doyle, Michael

2012-06-01

A series of botulism challenge studies were performed to determine the possibility of production of botulinum toxin in mussels (Mytilus edulis) held under a commercial high-oxygen (60 to 65% O(2)), modified atmosphere packaging (MAP) condition. Spore mixtures of six strains of nonproteolytic Clostridium botulinum were introduced into mussel MAP packages receiving different packaging buffers with or without the addition of lactic acid bacteria. Dye studies and package flipping trials were conducted to ensure internalization of spores by packed mussels. Inoculated mussel packages were stored at normal (4°C) and abusive (12°C) temperatures for 21 and 13 days, respectively, which were beyond the packaged mussels' intended shelf life. Microbiological and chemical analyses were conducted at predetermined intervals (a total of five sampling times at each temperature), including total aerobic plate counts, C. botulinum counts, lactic acid bacterial counts, package headspace gas composition, pH of packaging buffer and mussel meat, and botulinum toxin assays of packaging buffer and mussel meat. Results revealed that C. botulinum inoculated in fresh mussels packed under MAP packaging did not produce toxin, even at an abusive storage temperature and when held beyond their shelf life. No evidence was found that packaging buffers or gas composition influenced the lack of botulinum toxin production in packed mussels.

Management and Economic Implications of Bundling and Block Booking of Television and Cable Programming.

ERIC Educational Resources Information Center

Picard, Robert G.

Bundling, a practice which has increased dramatically in the television and cable industries in recent years, occurs when program distributors package groups of movies and episodes of series, and then sell licenses to use these packages to TV stations and cable channels. Typically, such bundled packages include both highly desirable and less…

Grouping Students and Pacing Instruction. Learning Package No. 15.

ERIC Educational Resources Information Center

Nelson, Carol; Smith, Carl, Comp.

Originally developed for the Department of Defense Schools (DoDDS) system, this learning package on grouping students and pacing instruction is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes a comprehensive search of the ERIC database; a lecture giving an overview on the topic; the full…

Language Diversity and Reading Instruction. Learning Package No. 21.

ERIC Educational Resources Information Center

Nelson, Carol; Smith, Carl, Comp.

Originally developed for the Department of Defense Schools (DoDDS) system, this learning package on language diversity and reading instruction is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes a comprehensive search of the ERIC database; a lecture giving an overview on the topic; the…

Observation and Feedback. Learning Package No. 12.

ERIC Educational Resources Information Center

Aiex, Nola Kortner; Smith, Carl, Comp.

Originally developed for the Department of Defense Schools (DoDDS) system, this learning package on observation and feedback is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes a comprehensive search of the ERIC database; a lecture giving an overview on the topic; the full text of several…

Extending the Basal. Learning Package No. 13.

ERIC Educational Resources Information Center

Collins, Norma; Smith, Carl, Comp.

Originally developed for the Department of Defense Schools (DoDDS) system, this learning package on extending the basal is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes a comprehensive search of the ERIC database; a lecture giving an overview on the topic; the full text of several…

Using Skills and Strategies for Effective Learning. Learning Package No. 9.

ERIC Educational Resources Information Center

Hong, Zhang; Smith, Carl, Comp.

Originally developed for the Department of Defense Schools (DoDDS) system, this learning package on using skills and strategies for effective learning is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes a comprehensive search of the ERIC database; a lecture giving an overview on the…

Writing Strategies for Gifted Children. Learning Package No. 45.

ERIC Educational Resources Information Center

Hyslop, Nancy; Smith, Carl, Comp.

Originally developed as part of a project for the Department of Defense Schools (DoDDS) system, this learning package on writing strategies for gifted children is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes an overview of the project; a comprehensive search of the ERIC database; a…

Trends and Issues in Reading Education. Learning Package No. 11.

ERIC Educational Resources Information Center

Smith, Carl, Comp.

Originally developed for the Department of Defense Schools (DoDDS) system, this learning package on trends and issues in reading education is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes a comprehensive search of the ERIC database; a lecture giving an overview on the topic; the full…

The Changing Perspective in Reading Assessment. Learning Package No. 14.

ERIC Educational Resources Information Center

Simic, Marge; Smith, Carl, Comp.

Originally developed for the Department of Defense Schools (DoDDS) system, this learning package on changing perspective in reading assessment is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes a comprehensive search of the ERIC database; a lecture giving an overview on the topic; the…

Making Writing Public. Learning Package No. 35.

ERIC Educational Resources Information Center

Simic, Marge, Comp.; Smith, Carl, Ed.

Originally developed as part of a project for the Department of Defense Schools (DoDDS) system, this learning package on making writing public is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes an overview of the project; a comprehensive search of the ERIC database; a lecture giving an…

Promoting Language Growth across the Curriculum. Learning Package No. 18.

ERIC Educational Resources Information Center

Collins, Norma; Smith, Carl, Comp.

Originally developed for the Department of Defense Schools (DoDDS) system, this learning package on language across the curriculum is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes a comprehensive search of the ERIC database; a lecture giving an overview on the topic; the full text of…

Reading Programs for Gifted Readers. Learning Package No. 28.

ERIC Educational Resources Information Center

Collins, Norma, Comp.; Smith, Carl, Ed.

Originally developed as part of a project for the Department of Defense Schools (DoDDS) system, this learning package on reading programs for gifted readers is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes an overview of the project; a comprehensive search of the ERIC database; a…

Reader Response Theory and Related Instructional Strategies. Learning Package No. 24.

ERIC Educational Resources Information Center

Collins, Norma; Smith, Carl, Comp.

Originally developed for the Department of Defense Schools (DoDDS) system, this learning package on reader response theory and related instructional strategies is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes a comprehensive search of the ERIC database; a lecture giving an overview on…

Children and the Library. Learning Package No. 41.

ERIC Educational Resources Information Center

Simic, Marge, Comp.; Smith, Carl, Ed.

Originally developed as part of a project for the Department of Defense Schools (DoDDS) system, this learning package on children and the library is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes an overview of the project; a comprehensive search of the ERIC database; a lecture giving…

Integrating the Language Arts. Learning Package No. 48.

ERIC Educational Resources Information Center

Chao, Han-Hua, Comp.; Smith, Carl, Ed.

Originally developed as part of a project for the Department of Defense Schools (DoDDS) system, this learning package on integrating the language arts is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes an overview of the project; a comprehensive search of the ERIC database; a lecture…

Spelling and the Writing Process. Learning Package No. 36.

ERIC Educational Resources Information Center

Simic, Marge, Comp.; Smith, Carl, Ed.

Originally developed as part of a project for the Department of Defense Schools (DoDDS) system, this learning package on spelling and the writing process is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes an overview of the project; a comprehensive search of the ERIC database; a lecture…

Strategic Thinking through Writing. Learning Package No. 37.

ERIC Educational Resources Information Center

Hong, Zhang, Comp.; Smith, Carl, Ed.

Originally developed as part of a project for the Department of Defense Schools (DoDDS) system, this learning package on strategic thinking through writing is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes an overview of the project; a comprehensive search of the ERIC database; a…

Using Folk Literature. Learning Package No. 3.

ERIC Educational Resources Information Center

Smith, Carl, Comp.

Originally developed for the Department of Defense Schools (DoDDS) system, this learning package on using folk literature is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes a comprehensive search of the ERIC database; a lecture giving an overview on the topic; the full text of several…

Developing Listening and Speaking Skills. Learning Package No. 46.

ERIC Educational Resources Information Center

Hyslop, Nancy, Comp.; Smith, Carl, Ed.

Originally developed as part of a project for the Department of Defense Schools (DoDDS) system, this learning package on developing listening and speaking skills is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes an overview of the project; a comprehensive search of the ERIC database; a…

Appreciation of Literature. Learning Package No. 49.

ERIC Educational Resources Information Center

Kelly, Dawn, Comp.; Smith, Carl, Ed.

Originally developed as part of a project for the Department of Defense Schools (DoDDS) system, this learning package on appreciating literature is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes an overview of the project; a comprehensive search of the ERIC database; a lecture giving an…

Writing Apprehension and the Writing Process. Learning Package No. 32.

ERIC Educational Resources Information Center

Collins, Norma, Comp.; Smith, Carl, Ed.

Originally developed as part of a project for the Department of Defense Schools (DoDDS) system, this learning package on writing apprehension and the writing process is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes an overview of the project; a comprehensive search of the ERIC…

Involving Parents in the Reading Process. Learning Package No. 7.

ERIC Educational Resources Information Center

Simic, Marge; Smith, Carl, Comp.

Originally developed for the Department of Defense Schools (DoDDS) system, this learning package on involving parents in the reading process is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes a comprehensive search of the ERIC database; a lecture giving an overview on the topic; the full…

Collaborative and Cooperative Learning Techniques. Learning Package No. 6.

ERIC Educational Resources Information Center

Compton, Joe; Smith, Carl, Comp.

Originally developed for the Department of Defense Schools (DoDDS) system, this learning package on collaborative and cooperative learning techniques is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes a comprehensive search of the ERIC database; a lecture giving an overview on the topic;…

Motivating Low Performing Students. Learning Package No. 22.

ERIC Educational Resources Information Center

Collins, Norma; Smith, Carl, Comp.

Originally developed for the Department of Defense Schools (DoDDS) system, this learning package on motivating low performing students is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes a comprehensive search of the ERIC database; a lecture giving an overview on the topic; the full text…

Reading in the Content Areas. Learning Package No. 4.

ERIC Educational Resources Information Center

Collins, Norma; Smith, Carl, Comp.

Originally developed for the Department of Defense Schools (DoDDS) system, this learning package on reading in the content areas is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes a comprehensive search of the ERIC database; a lecture giving an overview on the topic; the full text of…

Television Viewing and Reading. Learning Package No. 23.

ERIC Educational Resources Information Center

Compton, Joe; Smith, Carl, Comp.

Originally developed for the Department of Defense Schools (DoDDS) system, this learning package on television viewing and reading is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes a comprehensive search of the ERIC database; a lecture giving an overview on the topic; the full text of…

Assessing Performance through Informal Techniques. Learning Package No. 10.

ERIC Educational Resources Information Center

Nelson, Carol; Smith, Carl, Comp.

Originally developed for the Department of Defense Schools (DoDDS) system, this learning package on assessing performance through informal techniques is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes a comprehensive search of the ERIC database; a lecture giving an overview on the topic;…

Developing Thinking Skills through Literature. Learning Package No. 19.

ERIC Educational Resources Information Center

Collins, Norma; Smith, Carl, Comp.

Originally developed for the Department of Defense Schools (DoDDS) system, this learning package on developing thinking skills through literature is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes a comprehensive search of the ERIC database; a lecture giving an overview on the topic; the…

Writing across the Curriculum. Learning Package No. 50.

ERIC Educational Resources Information Center

Kelly, Dawn, Comp.; Smith, Carl, Ed.

Originally developed as part of a project for the Department of Defense Schools (DoDDS) system, this learning package on writing across the curriculum is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes an overview of the project; a comprehensive search of the ERIC database; a lecture…

Ways To Evaluate Writing. Learning Package No. 47.

ERIC Educational Resources Information Center

Hyslop, Nancy, Comp.; Smith, Carl, Ed.

Originally developed as part of a project for the Department of Defense Schools (DoDDS) system, this learning package on ways to evaluate writing is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes an overview of the project; a comprehensive search of the ERIC database; a lecture giving…

Computers and Writing. Learning Package No. 33.

ERIC Educational Resources Information Center

Simic, Marge, Comp.; Smith, Carl, Ed.

Originally developed as part of a project for the Department of Defense Schools (DoDDS) system, this learning package on computers and writing is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes an overview of the project; a comprehensive search of the ERIC database; a lecture giving an…

Developing Oral Language. Learning Package No. 1.

ERIC Educational Resources Information Center

Hong, Zhang; Smith, Carl, Comp.

Originally developed for the Department of Defense Schools (DoDDS) system, this learning package on developing oral language is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes a comprehensive search of the ERIC database; a lecture giving an overview on the topic; the full text of several…

Process Variability and Capability in Candy Production and Packaging

ERIC Educational Resources Information Center

Lembke, Ronald S.

2016-01-01

In this short, in-class activity, students use fun size packages of M&Ms to study process variability, including a real-world application of C[subscript pk]. How process variability and legal requirements force the company to put "Not Labeled for Individual Retail Sale" on each fun size package is discussed, as is the economics of…

The Relationship between Reading and Writing. Learning Package No. 40.

ERIC Educational Resources Information Center

Collins, Norma, Comp.; Smith, Carl, Ed.

Originally developed as part of a project for the Department of Defense Schools (DoDDS) system, this learning package on the relationship between reading and writing is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes an overview of the project; a comprehensive search of the ERIC…

Expanding Thematic Units beyond the Textbook. Learning Package No. 2.

ERIC Educational Resources Information Center

Chao, Han-Hua; Smith, Carl, Comp.

Originally developed for the Department of Defense Schools (DoDDS) system, this learning package on expanding thematic units beyond the textbook is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes a comprehensive search of the ERIC database; a lecture giving an overview on the topic; the…

Writing as Exploration. Learning Package No. 31.

ERIC Educational Resources Information Center

Collins, Norma, Comp.; Smith, Carl, Ed.

Originally developed as part of a project for the Department of Defense Schools (DoDDS) system, this learning package on expressive writing is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes an overview of the project; a comprehensive search of the ERIC database; a lecture giving an…

14 CFR Appendix E to Part 60 - Qualification Performance Standards for Quality Management Systems for Flight Simulation Training...

Code of Federal Regulations, 2014 CFR

2014-01-01

... data made available to the NSPM (the validation data package) includes the aircraft manufacturer's... longer in business), and if appropriate, with the person who supplied the aircraft data package for the FFS for the purposes of receiving notification of data package changes. E1.13. A policy, process, or...

14 CFR Appendix E to Part 60 - Qualification Performance Standards for Quality Management Systems for Flight Simulation Training...

Code of Federal Regulations, 2012 CFR

2012-01-01

... data made available to the NSPM (the validation data package) includes the aircraft manufacturer's... longer in business), and if appropriate, with the person who supplied the aircraft data package for the FFS for the purposes of receiving notification of data package changes. E1.13. A policy, process, or...

Establishment of prostate cancer spheres from a prostate cancer cell line after phenethyl isothiocyanate treatment and discovery of androgen-dependent reversible differentiation between sphere and neuroendocrine cells.

PubMed

Chen, Yamei; Cang, Shundong; Han, Liying; Liu, Christina; Yang, Patrick; Solangi, Zeeshan; Lu, Quanyi; Liu, Delong; Chiao, J W

2016-05-03

Prostate cancer can transform from androgen-responsive to an androgen-independent phenotype. The mechanism responsible for the transformation remains unclear. We studied the effects of an epigenetic modulator, phenethyl isothiocyanate (PEITC), on the androgen-responsive LNCaP cells. After treatment with PEITC, floating spheres were formed with characteristics of prostate cancer stem cells (PCSC). These spheres were capable of self-renewal in media with and without androgen. They have been maintained in both types of media as long term cultures. Upon androgen deprivation, the adherent spheres differentiated to neuroendocrine cells (NEC) with decreased proliferation, expression of androgen receptor, and PSA. NEC reverse differentiated to spheres when androgen was replenished. The sphere cells expressed surface marker CD44 and had enhanced histone H3K4 acetylation, DNMT1 down-regulation and GSTP1 activation. We hypothesize that PEITC-mediated alteration in epigenomics of LNCaP cells may give rise to sphere cells, whereas reversible androgenomic alterations govern the shuttling between sphere PCSC and progeny NEC. Our findings identify unrecognized properties of prostate cancer sphere cells with multi-potential plasticity. This system will facilitate development of novel therapeutic agents and allow further exploration into epigenomics and androgenomics governing the transformation to hormone refractory prostate cancer.

Tobacco Packaging and Labeling Policies Under the U.S. Tobacco Control Act: Research Needs and Priorities

PubMed Central

2012-01-01

Introduction: The Family Smoking Prevention and Tobacco Control Act (the “Act”), enacted in June 2009, gave the U.S. Food and Drug Administration authority to regulate tobacco products. The current paper reviews the provisions for packaging and labeling, including the existing evidence and research priorities. Methods: Narrative review using electronic literature search of published and unpublished sources in 3 primary areas: health warnings, constituent labeling, and prohibitions on the promotional elements of packaging. Results: The Act requires 9 pictorial health warnings covering half of cigarette packages and 4 text warnings covering 30% of smokeless tobacco packages. The Act also prohibits potentially misleading information on packaging, including the terms “light” and “mild,” and provides a mandate to require disclosure of chemical constituents on packages. Many of the specific regulatory provisions are based on the extent to which they promote “greater public understanding of the risks of tobacco.” As a result, research on consumer perceptions has the potential to shape the design and renewal of health warnings and to determine what, if any, information on product constituents should appear on packages. Research on consumer perceptions of existing and novel tobacco products will also be critical to help identify potentially misleading information that should be restricted under the Act. Conclusion: Packaging and labeling regulations required under the Act will bring the United States in line with international standards. There is an immediate need for research to evaluate these measures to guide future regulatory action. PMID:22039072

Chemically Aware Model Builder (camb): an R package for property and bioactivity modelling of small molecules.

PubMed

Murrell, Daniel S; Cortes-Ciriano, Isidro; van Westen, Gerard J P; Stott, Ian P; Bender, Andreas; Malliavin, Thérèse E; Glen, Robert C

2015-01-01

In silico predictive models have proved to be valuable for the optimisation of compound potency, selectivity and safety profiles in the drug discovery process. camb is an R package that provides an environment for the rapid generation of quantitative Structure-Property and Structure-Activity models for small molecules (including QSAR, QSPR, QSAM, PCM) and is aimed at both advanced and beginner R users. camb's capabilities include the standardisation of chemical structure representation, computation of 905 one-dimensional and 14 fingerprint type descriptors for small molecules, 8 types of amino acid descriptors, 13 whole protein sequence descriptors, filtering methods for feature selection, generation of predictive models (using an interface to the R package caret), as well as techniques to create model ensembles using techniques from the R package caretEnsemble). Results can be visualised through high-quality, customisable plots (R package ggplot2). Overall, camb constitutes an open-source framework to perform the following steps: (1) compound standardisation, (2) molecular and protein descriptor calculation, (3) descriptor pre-processing and model training, visualisation and validation, and (4) bioactivity/property prediction for new molecules. camb aims to speed model generation, in order to provide reproducibility and tests of robustness. QSPR and proteochemometric case studies are included which demonstrate camb's application.Graphical abstractFrom compounds and data to models: a complete model building workflow in one package.

The Next Generation in Subsidence and Aquifer-System Compaction Modeling within the MODFLOW Software Family: A New Package for MODFLOW-2005 and MODFLOW-OWHM

NASA Astrophysics Data System (ADS)

Boyce, S. E.; Leake, S. A.; Hanson, R. T.; Galloway, D. L.

2015-12-01

The Subsidence and Aquifer-System Compaction Packages, SUB and SUB-WT, for MODFLOW are two currently supported subsidence packages within the MODFLOW family of software. The SUB package allows the calculation of instantaneous and delayed releases of water from distributed interbeds (relatively more compressible fine-grained sediments) within a saturated aquifer system or discrete confining beds. The SUB-WT package does not include delayed releases, but does perform a more rigorous calculation of vertical stresses that can vary the effective stress that causes compaction. This calculation of instantaneous compaction can include the effect of water-table fluctuations for unconfined aquifers on effective stress, and can optionally adjust the elastic and inelastic storage properties based on the changes in effective stress. The next generation of subsidence modeling in MODFLOW is under development, and will merge and enhance the capabilities of the SUB and SUB-WT Packages for MODFLOW-2005 and MODFLOW-OWHM. This new version will also provide some additional features such as stress dependent vertical hydraulic conductivity of interbeds, time-varying geostatic loads, and additional attributes related to aquifer-system compaction and subsidence that will broaden the class of problems that can be simulated. The new version will include a redesigned source code, a new user friendly input file structure, more output options, and new subsidence solution options. This presentation will discuss progress in developing the new package and the new features being implemented and their potential applications. By Stanley Leake, Scott E. Boyce, Randall T. Hanson, and Devin Galloway

High energy neutron dosimeter

DOEpatents

Rai, K.S.F.

1994-01-11

A device for measuring dose equivalents in neutron radiation fields is described. The device includes nested symmetrical hemispheres (forming spheres) of different neutron moderating materials that allow the measurement of dose equivalents from 0.025 eV to past 1 GeV. The layers of moderating material surround a spherical neutron counter. The neutron counter is connected by an electrical cable to an electrical sensing means which interprets the signal from the neutron counter in the center of the moderating spheres. The spherical shape of the device allows for accurate measurement of dose equivalents regardless of its positioning. 2 figures.

Diagnosis of a Poorly Performing Liquid Hydrogen Bulk Storage Sphere

NASA Technical Reports Server (NTRS)

Krenn, Angela G.

2011-01-01

There are two 850,000 gallon Liquid Hydrogen (LH2) storage spheres used to support the Space Shuttle Program; one residing at Launch Pad A and the other at Launch Pad B. The LH2 Sphere at Pad B has had a high boiloff rate since being brought into service in the 1960's. The daily commodity loss was estimated to be approximately double that of the Pad A sphere, and well above the minimum required by the sphere's specification. Additionally, after being re-painted in the late 1990's a "cold spot" appeared on the outer sphere which resulted in a poor paint bond, and mold formation. Thermography was used to characterize the area, and the boiloff rate was continually evaluated. All evidence suggested that the high boiloff rate was caused by an excessive heat leak into the inner sphere due to an insulation void in the annulus. Pad B was recently taken out of Space Shuttle program service which provided a unique opportunity to diagnose the sphere's poor performance. The sphere was drained and inerted, and then opened from the annular relief device on the top where a series of boroscoping operations were accomplished. Boroscoping revealed a large Perlite insulation void in the region of the sphere where the cold spot was apparent. Perlite was then trucked in and off-loaded into the annular void region until the annulus was full. The sphere has not yet been brought back into service.

Identification Of Cells With A Compact Microscope Imaging System With Intelligent Controls

NASA Technical Reports Server (NTRS)

McDowell, Mark (Inventor)

2006-01-01

A Microscope Imaging System (CMIS) with intelligent controls is disclosed that provides techniques for scanning, identifying, detecting and tracking mic?oscopic changes in selected characteristics or features of various surfaces including, but not limited to, cells, spheres, and manufactured products subject to difficult-to-see imperfections. The practice of the present invention provides applications that include colloidal hard spheres experiments, biological cell detection for patch clamping, cell movement and tracking, as well as defect identification in products, such as semiconductor devices, where surface damage can be significant, but difficult to detect. The CMIS system is a machine vision system, which combines intelligent image processing with remote control capabilities and provides the ability to autofocus on a microscope sample, automatically scan an image, and perform machine vision analysis on multiple samples simultaneously.

Tracking of Cells with a Compact Microscope Imaging System with Intelligent Controls

NASA Technical Reports Server (NTRS)

McDowell, Mark (Inventor)

2007-01-01

A Microscope Imaging System (CMIS) with intelligent controls is disclosed that provides techniques for scanning, identifying, detecting and tracking microscopic changes in selected characteristics or features of various surfaces including, but not limited to, cells, spheres, and manufactured products subject to difficult-to-see imperfections. The practice of the present invention provides applications that include colloidal hard spheres experiments, biological cell detection for patch clamping, cell movement and tracking, as well as defect identification in products, such as semiconductor devices, where surface damage can be significant, but difficult to detect. The CMIS system is a machine vision system, which combines intelligent image processing with remote control capabilities and provides the ability to autofocus on a microscope sample, automatically scan an image, and perform machine vision analysis on multiple samples simultaneously

Tracking of cells with a compact microscope imaging system with intelligent controls

NASA Technical Reports Server (NTRS)

McDowell, Mark (Inventor)

2007-01-01

A Microscope Imaging System (CMIS) with intelligent controls is disclosed that provides techniques for scanning, identifying, detecting and tracking microscopic changes in selected characteristics or features of various surfaces including, but not limited to, cells, spheres, and manufactured products subject to difficult-to-see imperfections. The practice of the present invention provides applications that include colloidal hard spheres experiments, biological cell detection for patch clamping, cell movement and tracking, as well as defect identification in products, such as semiconductor devices, where surface damage can be significant, but difficult to detect. The CMIS system is a machine vision system, which combines intelligent image processing with remote control capabilities and provides the ability to auto-focus on a microscope sample, automatically scan an image, and perform machine vision analysis on multiple samples simultaneously.

Operation of a Cartesian Robotic System in a Compact Microscope with Intelligent Controls

NASA Technical Reports Server (NTRS)

McDowell, Mark (Inventor)

2006-01-01

A Microscope Imaging System (CMIS) with intelligent controls is disclosed that provides techniques for scanning, identifying, detecting and tracking microscopic changes in selected characteristics or features of various surfaces including, but not limited to, cells, spheres, and manufactured products subject to difficult-to-see imperfections. The practice of the present invention provides applications that include colloidal hard spheres experiments, biological cell detection for patch clamping, cell movement and tracking, as well as defect identification in products, such as semiconductor devices, where surface damage can be significant, but difficult to detect. The CMIS system is a machine vision system, which combines intelligent image processing with remote control capabilities and provides the ability to autofocus on a microscope sample, automatically scan an image, and perform machine vision analysis on multiple samples simultaneously.

MWASTools: an R/bioconductor package for metabolome-wide association studies.

PubMed

Rodriguez-Martinez, Andrea; Posma, Joram M; Ayala, Rafael; Neves, Ana L; Anwar, Maryam; Petretto, Enrico; Emanueli, Costanza; Gauguier, Dominique; Nicholson, Jeremy K; Dumas, Marc-Emmanuel

2018-03-01

MWASTools is an R package designed to provide an integrated pipeline to analyse metabonomic data in large-scale epidemiological studies. Key functionalities of our package include: quality control analysis; metabolome-wide association analysis using various models (partial correlations, generalized linear models); visualization of statistical outcomes; metabolite assignment using statistical total correlation spectroscopy (STOCSY); and biological interpretation of metabolome-wide association studies results. The MWASTools R package is implemented in R (version  > =3.4) and is available from Bioconductor: https://bioconductor.org/packages/MWASTools/. m.dumas@imperial.ac.uk. Supplementary data are available at Bioinformatics online. © The Author(s) 2017. Published by Oxford University Press.

Is the test of senior friendly/child resistant packaging ethical?

PubMed

Bix, Laura; de la Fuente, Javier; Pimple, Kenneth D; Kou, Eric

2009-12-01

Research has documented the drastic reduction of unintentional poisonings of children since the introduction of child resistant (CR) packaging. However, studies also indicate that consumers report difficulty using CR packages, in part because tests which determine the 'senior friendliness' of CR designs that are used throughout the world disallow people with 'overt or obvious' disabilities from being test subjects. Our review of drug package usability suggests that the current tests of CR packaging can and should be revised to correct this problem. We use US legislation, regulation and data to exemplify these points, but the conclusions are applicable to all protocols that include the exclusionary provision.