40 CFR 57.102 - Eligibility.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., but not the cost of compliance). (i) Retrofit control technologies. (A) Sulfuric acid plant in conjunction with an adequately demonstrated replacement technology or process modification; (B) Magnesium... burning in conjunction with acid plant; (D) Electric Furnace; (E) Noranda process; (F) Fluid bed roaster...

Agglomerating combustor-gasifier method and apparatus for coal gasification

DOEpatents

Chen, Joseph L. P.; Archer, David H.

1976-09-21

A method and apparatus for gasifying coal wherein the gasification takes place in a spout fluid bed at a pressure of about 10 to 30 atmospheres and a temperature of about 1800.degree. to 2200.degree.F and wherein the configuration of the apparatus and the manner of introduction of gases for combustion and fluidization is such that agglomerated ash can be withdrawn from the bottom of the apparatus and gas containing very low dust loading is produced. The gasification reaction is self-sustaining through the burning of a stoichiometric amount of coal with air in the lower part of the apparatus to form the spout within the fluid bed. The method and apparatus are particularly suitable for gasifying coarse coal particles.

Contractor's STTR Phase I Final Report- Experimental Analysis and Model Development of Pyrolysis/Combustion of Coal/Biomass in a Bench Scale Spouted Bed Reactor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baird, Benjamin; Loebick, Codruta; Roychoudhury, Subir

During Phase I both experimental evaluation and computational validation of an advanced Spouted Bed Reactor (SBR) approach for biomass and coal combustion was completed. All Phase I objectives were met and some exceeded. Comprehensive insight on SBR operation was achieved via design, fabrication, and testing of a small demonstration unit with pulverized coal and biomass as feedstock at University of Connecticut (UCONN). A scale-up and optimization tool for the next generation of coal and biomass co-firing for reducing GHG emissions was also developed. The predictive model was implemented with DOE’s MFIX computational model and was observed to accurately mimic evenmore » unsteady behavior. An updated Spouted Bed Reactor was fabricated, based on model feedback, and experimentally displayed near ideal behavior. This predictive capability based upon first principles and experimental correlation allows realistic simulation of mixed fuel combustion in these newly proposed power boiler designs. Compared to a conventional fluidized bed the SBR facilitates good mixing of coal and biomass, with relative insensitivity to particle size and densities, resulting in improved combustion efficiency. Experimental data with mixed coal and biomass fuels demonstrated complete oxidation at temperatures as low as 500ºC. This avoids NOx formation and residual carbon in the waste ash. Operation at stoichiometric conditions without requiring cooling or sintering of the carrier was also observed. Oxygen-blown operation were tested and indicated good performance. This highlighted the possibility of operating the SBR at a wide range of conditions suitable for power generation and partial oxidation byproducts. It also supports the possibility of implementing chemical looping (for readily capturing CO 2 and SO x).« less

Experimental Analysis and Model Development of Pyrolysis/Combustion of Coal/Biomass in a Bench Scale Spouted Bed Reactor.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baird, Benjamin; Loebick, Codruta; Roychoudhury, Subir

During Phase I both experimental evaluation and computational validation of an advanced Spouted Bed Reactor (SBR) approach for biomass and coal combustion was completed. All Phase I objectives were met and some exceeded. Comprehensive insight on SBR operation was achieved via design, fabrication, and testing of a small demonstration unit with pulverized coal and biomass as feedstock at University of Connecticut (UCONN). A scale-up and optimization tool for the next generation of coal and biomass co-firing for reducing GHG emissions was also developed. The predictive model was implemented with DOE’s MFIX computational model and was observed to accurately mimic evenmore » unsteady behavior. An updated Spouted Bed Reactor was fabricated, based on model feedback, and experimentally displayed near ideal behavior. This predictive capability based upon first principles and experimental correlation allows realistic simulation of mixed fuel combustion in these newly proposed power boiler designs. Compared to a conventional fluidized bed the SBR facilitates good mixing of coal and biomass, with relative insensitivity to particle size and densities, resulting in improved combustion efficiency. Experimental data with mixed coal and biomass fuels demonstrated complete oxidation at temperatures as low as 500C. This avoids NOx formation and residual carbon in the waste ash. Operation at stoichiometric conditions without requiring cooling or sintering of the carrier was also observed. Oxygen-blown operation were tested and indicated good performance. This highlighted the possibility of operating the SBR at a wide range of conditions suitable for power generation and partial oxidation byproducts. It also supports the possibility of implementing chemical looping (for readily capturing CO2 and SOx).« less

Powder lemon juice containing oligosaccharides obtained by dextransucrase acceptor reaction synthesis and dehydrated in sprouted bed.

PubMed

Coelho, Raquel Macedo Dantas; Araújo, Antônia Daiana Andrade; Fontes, Cláudia Patrícia Mourão Lima; da Silva, Ana Raquel Araujo; da Costa, José Maria Correia; Rodrigues, Sueli

2015-09-01

Oligosaccharides can be synthesized using the sugars present in the fruit juices through the dextransucrase acceptor reaction. In the present work, the effect of reducing sugar and sucrose concentration on oligosaccharide formation in lemon juice was evaluated through response surface methodology. The oligosaccharide formation in lemon juice was favored at high concentrations of sucrose (75 g/L) and reducing sugar (75 g/L). At this synthesis conditions, an oligosaccharide concentration of 94.81 g/L was obtained with a conversion of 63.21% of the initial sugars into the target product. Oligosaccharides with degree of polymerization up to 11 were obtained. The lemon juice was dehydrated in spouted bed using maltodextrin as drying adjuvant. The powder obtained at 60°C with 20 % maltodextrin presented low moisture (2.24 %), low water activity (Aw = 0.18) and the lowest reconstitution time (~46 s). The results showed that lemon juice is suitable for oligosaccharides enzyme synthesis and can be dehydrated in spouted bed.

II. Electrodeposition/removal of nickel in a spouted electrochemical reactor.

PubMed

Grimshaw, Pengpeng; Calo, Joseph M; Shirvanian, Pezhman A; Hradil, George

2011-08-17

An investigation is presented of nickel electrodeposition from acidic solutions in a cylindrical spouted electrochemical reactor. The effects of solution pH, temperature, and applied current on nickel removal/recovery rate, current efficiency, and corrosion rate of deposited nickel on the cathodic particles were explored under galvanostatic operation. Nitrogen sparging was used to decrease the dissolved oxygen concentration in the electrolyte in order to reduce the nickel corrosion rate, thereby increasing the nickel electrowinning rate and current efficiency. A numerical model of electrodeposition, including corrosion and mass transfer in the particulate cathode moving bed, is presented that describes the behavior of the experimental net nickel electrodeposition data quite well.

II. Electrodeposition/removal of nickel in a spouted electrochemical reactor

PubMed Central

Grimshaw, Pengpeng; Calo, Joseph M.; Shirvanian, Pezhman A.; Hradil, George

2011-01-01

An investigation is presented of nickel electrodeposition from acidic solutions in a cylindrical spouted electrochemical reactor. The effects of solution pH, temperature, and applied current on nickel removal/recovery rate, current efficiency, and corrosion rate of deposited nickel on the cathodic particles were explored under galvanostatic operation. Nitrogen sparging was used to decrease the dissolved oxygen concentration in the electrolyte in order to reduce the nickel corrosion rate, thereby increasing the nickel electrowinning rate and current efficiency. A numerical model of electrodeposition, including corrosion and mass transfer in the particulate cathode moving bed, is presented that describes the behavior of the experimental net nickel electrodeposition data quite well. PMID:22039317

13. VIEW TO SOUTHEAST, BRICK SKINNER SALT ROASTER AND STEEL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

13. VIEW TO SOUTHEAST, BRICK SKINNER SALT ROASTER AND STEEL SKINNER SALT ROASTER. - Vanadium Corporation of America (VCA) Naturita Mill, 3 miles Northwest of Naturita, between Highway 141 & San Miguel River, Naturita, Montrose County, CO

12. VIEW TO SOUTH, BRICK SKINNER SALT ROASTER AND STEEL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

12. VIEW TO SOUTH, BRICK SKINNER SALT ROASTER AND STEEL SKINNER SALT ROASTER. - Vanadium Corporation of America (VCA) Naturita Mill, 3 miles Northwest of Naturita, between Highway 141 & San Miguel River, Naturita, Montrose County, CO

11. VIEW TO NORTH, STEELSKINNER SALT ROASTER AND BRICK SKINNER ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

11. VIEW TO NORTH, STEEL-SKINNER SALT ROASTER AND BRICK SKINNER SALT ROASTER (FOREGROUND), AND MECHANIC SHED, MILL WAREHOUSE AND DRYERS (BACKGROUND). - Vanadium Corporation of America (VCA) Naturita Mill, 3 miles Northwest of Naturita, between Highway 141 & San Miguel River, Naturita, Montrose County, CO

60. VIEW OF ROASTER ADDITION FROM WEST, LOCATION OF SYMONS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

60. VIEW OF ROASTER ADDITION FROM WEST, LOCATION OF SYMONS 3 BY 8 FEET VIBRATING SCREEN. SHOWS BAKER COOLER WITH DUST COLLECTOR DUCT AND DISCHARGE CHUTE ON LEFT. THE 14 INCH BELT CONVEYOR WAS SUPPORTED ON TWO BENTS IN CENTER OF VIEW AS IT CONNECTED WITH THE BUCKET ELEVATOR/ORE BIN TOWER, WHICH IN TURN FED THE ROASTER (BEHIND). THE BASE OF THE ROASTER EXHAUST STACK IS AT THE UPPER RIGHT. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

Chemsheet as a Simulation Platform for Pyrometallurgical Processes

NASA Astrophysics Data System (ADS)

Penttilä, Karri; Salminen, Justin; Tripathi, Nagendra; Koukkari, Pertti

ChemSheet is a thermodynamic multi-phase multi-component simulation software, which is used as an Add-in in Microsoft Excel. In ChemSheet, the unique Constrained Gibbs free energy method can be used to include dynamic constraints and reaction rates of kinetically slow reactions, yet retaining full consistency of the multiphase thermodynamic model. With appropriate data, ChemSheet models can be used to simulate reactors and processes in all fields of thermochemistry. The presentation will cover off-line modeling of Cu-flash smelters and advanced thermochemical simulation coupled with on-line process control of Cu-Ni smelting. The presentation will describe an off-line model of Cu-smelter based on critically assessed properties of the Al-Ca-Cu-Fe-O-S-Si -system (slag, matte and liquid metal) by using the quasichemical model. A four-stage reactor model (shaft, settler, uptake and bath) is used for optimizing process parameters and feed particle distribution. As a second example, an advanced thermochemical model of a Ni-Cu sulphide smelting plant will be given. The on-line model covers the operation of treating Ni-Cu-S concentrate via roasters, electric furnace and converters, producing a high grade Bessemer matte product for further refining. The model integrates the thermochemistry of the roasters and electric furnace, and predicts important process parameters such as degree of sulphur elimination in the fluid-bed roasters, matte grade, iron metallization, slag losses and the iron to silica ratio in the electric furnace slag. Both models can be used to assist process engineers and operators in calculating the addition rates of coke, flux and air for different feed scenarios.

7. VIEW OF THE CHIP ROASTER LOCATED IN BUILDING 447. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

7. VIEW OF THE CHIP ROASTER LOCATED IN BUILDING 447. THE CHIP ROASTER BURNED URANIUM CHIPS FROM MACHINING AREAS TO AN OXIDE, A MORE STABLE FORM FOR DISPOSAL. (4/27/55) - Rocky Flats Plant, Non-Nuclear Production Facility, South of Cottonwood Avenue, west of Seventh Avenue & east of Building 460, Golden, Jefferson County, CO

SPOUTED BED DESIGN CONSIDERATIONS FOR COATED NUCLEAR FUEL PARTICLES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marshall, Douglas W.

High Temperature Gas Cooled Reactors (HTGRs) are fueled with tristructural isotropic (TRISO) coated nuclear fuel particles embedded in a carbon-graphite fuel body. TRISO coatings consist of four layers of pyrolytic carbon and silicon carbide that are deposited on uranium ceramic fuel kernels (350µm – 500µm diameters) in a concatenated series of batch depositions. Each layer has dedicated functions such that the finished fuel particle has its own integral containment to minimize and control the release of fission products into the fuel body and reactor core. The TRISO coatings are the primary containment structure in the HTGR reactor and must havemore » very high uniformity and integrity. To ensure high quality TRISO coatings, the four layers are deposited by chemical vapor deposition (CVD) using high purity precursors and are applied in a concatenated succession of batch operations before the finished product is unloaded from the coating furnace. These depositions take place at temperatures ranging from 1230°C to 1550°C and use three different gas compositions, while the fuel particle diameters double, their density drops from 11.1 g/cm3 to 3.0 g/cm3, and the bed volume increases more than 8-fold. All this is accomplished without the aid of sight ports or internal instrumentation that could cause chemical contamination within the layers or mechanical damage to thin layers in the early stages of each layer deposition. The converging section of the furnace retort was specifically designed to prevent bed stagnation that would lead to unacceptably high defect fractions and facilitate bed circulation to avoid large variability in coating layer dimensions and properties. The gas injection nozzle was designed to protect precursor gases from becoming overheated prior to injection, to induce bed spouting and preclude bed stagnation in the bottom of the retort. Furthermore, the retort and injection nozzle designs minimize buildup of pyrocarbon and silicon carbide on the retort wall and manage nozzle orifice accretions. The equipment and operating methods have yielded very good reproducibility in the TRISO coated particles batches.« less

24. VIEW OF MILL FROM UPPER TAILINGS POND (NORTH). ROASTER ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

24. VIEW OF MILL FROM UPPER TAILINGS POND (NORTH). ROASTER ON LEFT WITH ELEVATOR/CRUSHED ORE BIN TOWER TO RIGHT. MAIN MILL BUILDING IN CENTER WITH THICKENER ADDITION TO RIGHT. MACHINE SHOP ON CRUDE ORE BIN TERRACE ABOVE ROASTER. THE LOCATION OF THE 100,000 GALLON MILL WATER TANK CAN BE SEEN AT THE CENTER RIGHT NEAR THE TOP OF THE MOUNTAIN. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

165. VIEW OF MILL FROM UPPER TAILINGS POND (NORTH). ROASTER ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

165. VIEW OF MILL FROM UPPER TAILINGS POND (NORTH). ROASTER ON LEFT WITH ELEVATOR/CRUSHED ORE BIN TOWER TO RIGHT. MAIN MILL BUILDING IN CENTER WITH THICKENER ADDITION TO RIGHT. MACHINE SHOP ON CRUDE ORE BIN TERRACE ABOVE ROASTER. THE LOCATION OF THE 100,000 GALLON MILL WATER TANK CAN BE SEEN AT THE CENTER RIGHT NEAR THE TOP OF THE MOUNTAIN - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

The mathematical model that describes the periodic spouting of a geyser induced by boiling

NASA Astrophysics Data System (ADS)

Kagami, Hiroyuki

2017-04-01

We have derived and modified the dynamical model of a geyser induced by gas inflow and regular or irregular spouting dynamics of geysers induced by gas inflow has been reproduced by the model. On the other hand, though we have derived the dynamical model of a geyser induced by boiling, periodic change between the spouting state and the pause state has not been adequately modeled by the model. In this connection, concerning a geyser induced by gas inflow we have proposed the model as described below. Because pressure in the spouting tube decreases obeying to the Bernoulli's theorem when the spouting state begins and water in the spouting tube begins to flow, inflow of groundwater into the spouting tube occurs. When the amount of this inflow reaches a certain amount, the spouting state transforms to the pause state. In this study, by applying this idea to the dynamical model of a geyser induced by boiling, the periodic change between the spouting state and the pause state could be reappeared. As a result, the whole picture of the spouting mechanism of a geyser induced by boiling became clear. This research results would give hints on engineering repair in order to prevent the weakening or the depletion of the geyser. And this study would be also useful for protection of geysers as tourism and environmental resources.

The characterization, mobility, and persistence of roaster-derived arsenic in soils at Giant Mine, NWT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bromstad, Mackenzie J.; Wrye, Lori A.; Jamieson, Heather E.

Approximately 20,000 tonnes of arsenic (As)-bearing emissions from roasting gold (Au)-bearing arsenopyrite ore were aerially released from 1949 to 1999 at Giant Mine, near Yellowknife, Canada. Soil samples collected within 4 km of the former roaster from sites undisturbed by mining or other human activity contain up to 7700 mg/kg total As. Total As concentrations are highest within a few cm of the surface, and particularly enriched in soil pockets on rock outcrops. Scanning electron microscopy and synchrotron microanalysis show that roaster-derived arsenic trioxide (As2O3) has persisted in shallow soils in the area. Roaster-generated maghemite and hematite are also present.more » These anthropogenic forms of As are much more common in near-surface soils than natural As-bearing minerals. Comparison of the proportions of As, Sb, and Au concentrations in outcrop soil samples and historic As2O3-rich dust captured by emission controls suggest most of the roaster-derived As in soils at Giant was likely deposited before 1964. Topographic restriction by rock outcrops and a dry, cold climate likely contribute to the persistence of As2O3 in outcrop soils.« less

58. ROASTER ADDITION INTERIOR FROM EAST, VIEW OF DISCHARGE CREW ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

58. ROASTER ADDITION INTERIOR FROM EAST, VIEW OF DISCHARGE CREW DRIVE WITH GAS PIPING FOR HEARTH FIRING. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

Low cost silicon solar array project silicon materials task: Establishment of the feasibility of a process capable of low-cost, high volume production of silane (step 1) and the pyrolysis of silane to semiconductor-grade silicon (step 2)

NASA Technical Reports Server (NTRS)

Breneman, W. C.; Farrier, E. G.; Rexer, J.

1977-01-01

Extended operation of a small process-development unit routinely produced high quality silane in 97+% yield from dichlorosilane. The production rate was consistent with design loadings for the fractionating column and for the redistribution reactor. A glass fluid-bed reactor was constructed for room temperature operation. The behavior of a bed of silcon particles was observed as a function of various feedstocks, component configurations, and operating conditions. For operating modes other than spouting, the bed behaved in an erratic and unstable manner. A method was developed for casting molten silicon powder into crack-free solid pellets for process evaluation. The silicon powder was melted and cast into thin walled quartz tubes that sacrificially broke on cooling.

4. VIEW TO NORTHEAST, SKINNER SALT ROASTERS, SAMPLING BUILDING, WATER ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. VIEW TO NORTHEAST, SKINNER SALT ROASTERS, SAMPLING BUILDING, WATER TOWER, AND OFFICE BUILDING. - Vanadium Corporation of America (VCA) Naturita Mill, 3 miles Northwest of Naturita, between Highway 141 & San Miguel River, Naturita, Montrose County, CO

55. VIEW OF ROASTER ADDITION FROM NORTH. ELEVATOR/ORE BIN ADDITION ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

55. VIEW OF ROASTER ADDITION FROM NORTH. ELEVATOR/ORE BIN ADDITION TO RIGHT (WEST) WITH BAKER COOLER IN FRONT. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

25. VIEW OF MILL FROM UPPER TAILINGS POND. SHOWS ROASTER ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

25. VIEW OF MILL FROM UPPER TAILINGS POND. SHOWS ROASTER ON LEFT EDGE OF VIEW. THE SECONDARY THICKENER No. 7 IS OFF VIEW TO THE RIGHT. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

11. BALD MOUNTAIN MILL, EXTERIOR FROM NORTHEAST, c. 194059. ROASTER ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

11. BALD MOUNTAIN MILL, EXTERIOR FROM NORTHEAST, c. 1940-59. ROASTER AND OTHER UNOXIDIZED ORE CIRCUIT ADDITIONS PRESENT, ALONG WITH SECONDARY THICKENER No. 7 AND ADDITIONS TO MACHINE SHOP. CREDIT JW. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

The effects of different dry roast parameters on peanut quality using an industrial, belt-type roaster simulator

USDA-ARS?s Scientific Manuscript database

Recent lab scale experiments demonstrated that peanuts roasted to equivalent surface colors at different temperature/time combinations can vary substantially in chemical and physical properties related to product quality. This study expanded that approach to a pilot plant scale roaster that simulate...

56. VIEW OF ROASTER ADDITION FROM NORTH. ELEVATOR/ORE BIN TOWER ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

56. VIEW OF ROASTER ADDITION FROM NORTH. ELEVATOR/ORE BIN TOWER WAS FED BY THE 14 INCH BELT CONVEYOR SUPPORTED ON BENT, LOWER RIGHT. THE ROTATING BAKER COOLER IS SUPPORTED BY A CONCRETE FOUNDATION TROUGH. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

54. VIEW OF ROASTER ADDITION FROM SOUTHEAST. SHOWS ELEVATOR/ORE BIN ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

54. VIEW OF ROASTER ADDITION FROM SOUTHEAST. SHOWS ELEVATOR/ORE BIN ADDITION ON LEFT WITH BASE OF EXHAUST STACK, PORTION OF TOPPLED STACK ON LOWER RIGHT IN VIEW, AND UPPER TAILINGS POND BEYOND. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

Kinetics of color development of peanuts during dry roasting using a batch roaster

USDA-ARS?s Scientific Manuscript database

The kinetics of color development during peanut roasting were investigated at roasting temperatures from 149 to 204 °C which produced Hunter L color values of 25 to 65. Preliminary and equivalent roasting trials were conducted using a batch roaster simulating the parameters of an industrial continuo...

The Legacy of Arsenic Contamination from Giant Mine, Northern Canada: An Assessment of Impacts Based on Lake Water and Lake Sediment Core Analysis

NASA Astrophysics Data System (ADS)

Blais, J. M.; Korosi, J.

2016-12-01

The Giant Mine, which operated between 1948 and 2004 and located near the City of Yellowknife (Northwest Territories, Canada), has left a legacy of arsenic, antimony, and mercury contamination extending to the present day. Over 20,000 tonnes of arsenic trioxide dust was released from roaster stack emissions during its first 10 years of operations, leading to a significant contamination of the surrounding landscape. Here we present a summary of impacts by the recent contamination from Giant Mine on the surrounding region. A survey we conducted of 25 lakes of the region in 2010 revealed that most lake water within a 15 km radius of the roaster stack had arsenic concentrations in water > 10 mg/L, the standard for drinking water, with concentrations declining exponentially with increasing distance from the roaster stack. Sediment cores from lakes were collected near the Giant Mine roaster stack and radiometrically dated by 137Cs and excess 210Pb. Arsenic concentrations in these sediments increased by 1700% during the 1950s and 60s, consistent with the history of arsenic releases from roaster emissions. Correspondingly, pelagic diatoms and cladocerans were extirpated from one lake during this period, based on microfossil analysis of lake sediment deposits. Sediment core analysis further showed that this lake ecosystem has not recovered, even ten years after closure of the mine. Likely causes for the lack of recent recovery are explored with the use of sediment toxicity bioassays, using a novel paleo-ecotoxicological approach of using toxicity assessments of radiometrically dated lake sediment horizons.

9 CFR 381.170 - Standards for kinds and classes, and for cuts of raw poultry.

Code of Federal Regulations, 2014 CFR

2014-01-01

...) Ducks—(i) Duckling. A “duckling” is a young duck (less than 8 weeks of age), of either sex, that is tender-meated and has a soft bill and soft windpipe. (ii) Roaster duck. A “roaster duck” is a young duck... hardened and a windpipe that is easily dented. (iii) Mature duck or old duck. A “mature duck” or an “old...

Numerical Study of Impingement Location of Liquid Jet Poured from a Tilting Ladle with Lip Spout

NASA Astrophysics Data System (ADS)

Castilla, R.; Gamez-Montero, P. J.; Raush, G.; Khamashta, M.; Codina, E.

2017-04-01

A new approach for simulating liquid poured from a tilting lip spout is presented, using neither a dynamic mesh nor the moving solid solution method. In this case only the tilting ladle is moving, so we propose to rotate the gravitational acceleration at an angular velocity prescribed by a geometrical and dynamical calculation to keep the poured flow rate constant. This angular velocity is applied to modify the orientation of the gravity vector in computational fluid dynamics (CFD) simulations using the OpenFOAM® toolbox. Also, fictitious forces are considered. The modified solver is used to calculate the impingement location for six spout geometries and compare the jet dispersion there. This method could offer an inexpensive tool to calculate optimal spout geometries to reduce sprue size in the metal casting industry.

ELECTRIC FURNACES TILT AROUND A PIVOT UNDER THE SPOUT TO ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

ELECTRIC FURNACES TILT AROUND A PIVOT UNDER THE SPOUT TO FILL BULL LADLES BELOW THE CHARGING DECK. THE REAR VIEW OF A POURING ELECTRIC FURNACE FROM THE CHARGING DECK IS SHOWN HERE. - Southern Ductile Casting Company, Melting, 2217 Carolina Avenue, Bessemer, Jefferson County, AL

Collecting maple sap with unvented spouts, using aerial and ground lines

Treesearch

H. Clay Smith; Carter B. Gibbs

1971-01-01

Two methods of using plastic tubing to collect sugar maple sap were tried: aerial lines and ground lines. Unvented spouts were used in both. We found that the sap yields collected from the aerial and ground lines were not statistically different from each other.

CFD Modelling Applied to the Co-Combustion of Paper Sludge and Coal in a 130 t/h CFB Boiler

NASA Astrophysics Data System (ADS)

Yu, Z. S.; Ma, X. Q.; Lai, Z. Y.; Xiao, H. M.

Three-dimensional mathematical model has been developed as a tool for co-combustion of paper sludge and coal in a 130 tJh Circulating Fluidized Bed (CFB) boiler. Mathematical methods had been used based on a commercial software FLUENT for combustion. The predicted results of CFB furnace show that the co-combustion of paper sludge/coal is initially intensively at the bottom of bed; the temperature reaches its maximum in the dense-phase zone, around l400K. It indicates that paper sludge spout into furnace from the recycle inlet can increase the furnace maximum temperature (l396.3K), area-weighted average temperature (l109.6K) and the furnace gas outlet area-weighted average temperature(996.8K).The mathematical modeling also predicts that 15 mass% paper sludge co-combustion is the highest temperature at the flue gas outlet, it is 1000.8K. Moreover, it is proved that mathematical models can serve as a tool for detailed analysis of co-combustion of paper sludge and coal processes in a circulating fluidized bed furnace when in view of its convenience. The results gained from numerical simulation show that paper sludge enter into furnace from the recycle inlet excelled than mixing with coal and at the underside of phase interface.

Acidifier application rate impacts on ammonia emissions from US roaster chicken houses

NASA Astrophysics Data System (ADS)

Shah, Sanjay B.; Grimes, Jesse L.; Oviedo-Rondón, Edgar O.; Westerman, Philip W.

2014-08-01

Due to its potential environmental and public health impacts, emissions of ammonia (NH3) as well as several other gases from US livestock farms may be regulated. Broiler houses are important sources of NH3 emissions. However, there are no emissions data from roaster (8-12 wk old broilers, ˜4 kg ea.) houses. Producers treat the litter in broiler houses with acidifiers, such as sodium bisulfate (SBS, NaHSO4) to reduce ammonia production and protect bird health. However, there is very little data on the effect of acidifiers, particularly at high application rates on ammonia emissions. The impact of different SBS application rates [High (0.95-1.46 kg m-2, whole house), Medium (0.73 kg m-2, whole house), Low (0.37-0.49 kg m-2, whole house), and Control (0.37-0.49 kg m-2, brood chamber)] on ammonia emissions was evaluated in commercial roaster houses over 22 months spanning eight flocks. Ammonia emission from each fan was measured with an acid scrubber that operated only when the fan operated. Emissions were calculated using >95% measured data with the rest being estimated using robust methods. Exhaust ammonia-N concentrations were inversely correlated with the SBS application rates. Emission rates on animal unit (AU, where 1 AU = 500 kg live-mass) basis (ER, g d-1 AU-1) were reduced by 27, 13, and 5%, respectively, in the High, Medium, and Low treatments vs. the Control treatment (mean: 100 g d-1 AU-1, range: 86-114 g d-1 AU-1). Emission rates for the Control treatment measured in this study on roasters were mostly higher than ERs in the literature. Differences in ERs are not only due to diet, environmental and management conditions, but also due to measurement methods.

29 CFR 1919.2 - Definition of terms.

Code of Federal Regulations, 2010 CFR

2010-07-01

... horizontal plane by guys (vangs). The term includes shear legs. (2) Crane means a mechanical device, intended... integral part of the machine. A crane may be a fixed or mobile machine. (3) Bulk cargo spout means a spout... ton of 2,000 pounds when applied to shore-based material handling devices or to shore-type cranes...

40 CFR 59.653 - How do I test portable fuel containers?

Code of Federal Regulations, 2010 CFR

2010-07-01

.... Perform the following spout actuation and inversion steps at the end on the slosh testing, and at the end of the preconditioning soak. (i) Perform one complete actuation/inversion cycle per day for ten days. (ii) One actuation/inversion cycle consists of the following steps: (A) Remove and replace the spout...

Burying by rats in response to aversive and nonaversive stimuli

PubMed Central

Poling, Alan; Cleary, James; Monaghan, Michael

1981-01-01

Previous investigations have shown that rats bury a variety of conditioned and unconditioned aversive stimuli. Such burying has been considered as a species-typical defensive reaction. In the present studies, rats buried spouts filled with Tabasco sauce, or condensed milk to which a taste aversion was conditioned, but did not bury water-filled spouts or spouts filled with a palatable novel food (apple juice) to which a taste aversion was not conditioned. However, in other experiments rats consistently and repeatedly buried Purina Rat Chow, Purina Rat Chow coated with quinine, and glass marbles. This indicates that a variety of stimuli, not all aversive or novel, evoke burying by rats. Whereas the behavior may reasonably be considered as a species-typical defensive behavior in some situations, the wide range of conditions that occasion burying suggests that the behavior has no single biological function. PMID:16812198

Waste Water Treatment Apparatus and Methods

NASA Technical Reports Server (NTRS)

Plawsky, Joel L. (Inventor); Paccione, John D. (Inventor); Littman, Howard (Inventor)

2014-01-01

An improved draft tube spout fluid bed (DTSFB) mixing, handling, conveying, and treating apparatus and systems, and methods for operating are provided. The apparatus and systems can accept particulate material and pneumatically or hydraulically conveying the material to mix and/or treat the material. In addition to conveying apparatus, a collection and separation apparatus adapted to receive the conveyed particulate material is also provided. The collection apparatus may include an impaction plate against which the conveyed material is directed to improve mixing and/or treatment. The improved apparatus are characterized by means of controlling the operation of the pneumatic or hydraulic transfer to enhance the mixing and/or reacting by controlling the flow of fluids, for example, air, into and out of the apparatus. The disclosed apparatus may be used to mix particulate material, for example, mortar; react fluids with particulate material; coat particulate material, or simply convey particulate material.

Flash pyrolysis of forestry residues from the Portuguese Central Inland Region within the framework of the BioREFINA-Ter project.

PubMed

Amutio, Maider; Lopez, Gartzen; Alvarez, Jon; Moreira, Rui; Duarte, Gustavo; Nunes, Joao; Olazar, Martin; Bilbao, Javier

2013-02-01

The feasibility of the valorization by flash pyrolysis of forest shrub wastes, namely bushes (Cytisus multiflorus, Spartium junceum, Acacia dealbata and Pterospartum tridentatum) has been studied in a conical spouted bed reactor operating at 500 °C, with a continuous biomass feed and char removal. High bio-oil yields in the 75-80 wt.% range have been obtained for all of the materials, with char yields between 16 and 23 wt.% and low gas yields (4-5 wt.%). Bio-oils are composed mainly of water (accounting for a concentration in the 34-40 wt.% range in the bio-oil), phenols, ketones, acids and furans, with lower contents of saccharides, aldehydes and alcohols. Although their composition depends on the raw material, the compounds are similar to those obtained with more conventional feedstocks. Copyright © 2012 Elsevier Ltd. All rights reserved.

Methods and apparatus for handling or treating particulate material

NASA Technical Reports Server (NTRS)

Littman, Howard (Inventor); Plawsky, Joel L. (Inventor); Paccione, John D. (Inventor)

2009-01-01

An improved draft tube spout fluid bed (DTSFB) mixing, handling, conveying, and treating apparatus and systems, and methods for operating are provided. The apparatus and systems can accept particulate material and pneumatically or hydraulically conveying the material to mix and/or treat the material. In addition to conveying apparatus, a collection and separation apparatus adapted to receive the conveyed particulate material is also provided. The collection apparatus may include an impaction plate against which the conveyed material is directed to improve mixing and/or treatment. The improved apparatus are characterized by means of controlling the operation of the pneumatic or hydraulic transfer to enhance the mixing and/or reacting by controlling the flow of fluids, for example, air, into and out of the apparatus. The disclosed apparatus may be used to mix particulate material, for example, mortar; react fluids with particulate material; coat particulate material, or simply convey particulate material.

Fluidized Bed Asbestos Sampler Design and Testing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Karen E. Wright; Barry H. O'Brien

A large number of samples are required to characterize a site contaminated with asbestos from previous mine or other industrial operations. Current methods, such as EPA Region 10’s glovebox method, or the Berman Elutriator method are time consuming and costly primarily because the equipment is difficult to decontaminate between samples. EPA desires a shorter and less costly method for characterizing soil samples for asbestos. The objective of this was to design and test a qualitative asbestos sampler that operates as a fluidized bed. The proposed sampler employs a conical spouted bed to vigorously mix the soil and separate fine particulatemore » including asbestos fibers on filters. The filters are then analyzed using transmission electron microscopy for presence of asbestos. During initial testing of a glass prototype using ASTM 20/30 sand and clay fines as asbestos surrogates, fine particulate adhered to the sides of the glass vessel and the tubing to the collection filter – presumably due to static charge on the fine particulate. This limited the fines recovery to ~5% of the amount added to the sand surrogate. A second prototype was constructed of stainless steel, which improved fines recovery to about 10%. Fines recovery was increased to 15% by either humidifying the inlet air or introducing a voltage probe in the air space above the sample. Since this was not a substantial improvement, testing using the steel prototype proceeded without using these techniques. Final testing of the second prototype using asbestos suggests that the fluidized bed is considerably more sensitive than the Berman elutriator method. Using a sand/tremolite mixture with 0.005% tremolite, the Berman elutriator did not segregate any asbestos structures while the fluidized bed segregated an average of 11.7. The fluidized bed was also able to segregate structures in samples containing asbestos at a 0.0001% concentration, while the Berman elutriator method did not detect any fibers at this concentration. Opportunities for improvement with the fluidized bed include improving reproducibility among replicates, increasing mass recovery, improving the lid gasket seal.« less

Influence of water quench cooling on degassing and aroma stability of roasted coffee.

PubMed

Baggenstoss, Juerg; Poisson, Luigi; Luethi, Regina; Perren, Rainer; Escher, Felix

2007-08-08

Coffee roasting experiments with air cooling versus water quench cooling were carried out on laboratory scale with a fluidized-bed hot air roasting system (200 g batch size) and on production scale with a rotating bowl roaster (320 kg batch size). Two series of coffees with different water contents resulted, which were stored at 25 degrees C under normal atmospheric conditions. Carbon dioxide desorption was followed and stability of selected aroma compounds was tested with headspace solid-phase microextraction-gas chromatography-mass spectrometry (SPME-GC-MS) and stable isotope labeled compounds as internal standards. Degassing is faster in water-quenched coffees with higher moisture content, but pore size distribution in the different coffee samples did not correlate with degassing behavior. Bean firmness, which increases with increasing moisture content, might have an influence on degassing. Air- and water-quenched coffees exhibit similar stability of most aroma compounds despite different degassing behavior. However, evolution of dimethyl trisulfide was different in coffees with increased water content. This suggests higher thiol oxidation rates, a factor that is cited to be related to a faster loss of freshness attributes.

25. DETAIL OF INSCRIPTION ON BAKE OVEN WHICH READS: PREMIUM ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

25. DETAIL OF INSCRIPTION ON BAKE OVEN WHICH READS: PREMIUM PATENT BAKE OVEN ROASTER BY ALFRED H. REIP NO. 337 BALT. STREET BALTIMORE - Hazelwood, 18611 Queen Anne Road, Upper Marlboro, Prince George's County, MD

10. VIEW TO SOUTHEAST, SAMPLING BUILDING, FOUNDATION, WATER TOWER, AND ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

10. VIEW TO SOUTHEAST, SAMPLING BUILDING, FOUNDATION, WATER TOWER, AND SKINNER SALT ROASTERS. - Vanadium Corporation of America (VCA) Naturita Mill, 3 miles Northwest of Naturita, between Highway 141 & San Miguel River, Naturita, Montrose County, CO

Innovations in coating technology.

PubMed

Behzadi, Sharareh S; Toegel, Stefan; Viernstein, Helmut

2008-01-01

Despite representing one of the oldest pharmaceutical techniques, coating of dosage forms is still frequently used in pharmaceutical manufacturing. The aims of coating range from simply masking the taste or odour of drugs to the sophisticated controlling of site and rate of drug release. The high expectations for different coating technologies have required great efforts regarding the development of reproducible and controllable production processes. Basically, improvements in coating methods have focused on particle movement, spraying systems, and air and energy transport. Thereby, homogeneous distribution of coating material and increased drying efficiency should be accomplished in order to achieve high end product quality. Moreover, given the claim of the FDA to design the end product quality already during the manufacturing process (Quality by Design), the development of analytical methods for the analysis, management and control of coating processes has attracted special attention during recent years. The present review focuses on recent patents claiming improvements in pharmaceutical coating technology and intends to first familiarize the reader with the available procedures and to subsequently explain the application of different analytical tools. Aiming to structure this comprehensive field, coating technologies are primarily divided into pan and fluidized bed coating methods. Regarding pan coating procedures, pans rotating around inclined, horizontal and vertical axes are reviewed separately. On the other hand, fluidized bed technologies are subdivided into those involving fluidized and spouted beds. Then, continuous processing techniques and improvements in spraying systems are discussed in dedicated chapters. Finally, currently used analytical methods for the understanding and management of coating processes are reviewed in detail in the last section of the review.

Speciation of airborne dust from a nickel refinery roasting operation.

PubMed

Andersen, I; Berge, S R; Resmann, F

1998-04-01

Earlier work-related lung and nasal cancer studies included estimates of exposures to different nickel species in the refinery. Based on the metallurgy, only insoluble nickel was believed to be present around the roasters but mixed exposure was assumed in most areas, including the tankhouse. Occasional leaching tests of samples from the roaster area have indicated the presence of soluble nickel. This study reports on five parallel sets of dust samples collected from different floors with standard equipment and treated as follows. Two sets were leached with an ammonium citrate buffer at pH 4.4. Undissolved material was treated with HClO4/HNO3, evaporated to dryness and dissolved in HCl, Ni, Cu, Co, Fe, Se, and As were determined in both fractions. Water soluble Ni was found in all samples, ranging from 5-35%. Sulfate in the solutions correlated nearly stoichiometrically to the total metal content. The three remaining sets were investigated by, respectively, differential leaching, X-ray diffraction and scanning electron microscopy. The percentage of soluble nickel found by differential leaching corresponded well with those obtained by the simplified procedure. X-Ray diffraction analysis showed the presence of NiSO4.6H2O as well as oxides of Ni and Cu. This study indicates mixed exposures also in the roaster area. It also clearly indicates that basing exposure on the metallurgy alone can lead to serious misjudgements. The impact of this new information on the interpretation of cancer incidence at this refinery must await the analysis in an ongoing case-reference study.

Online monitoring of coffee roasting by proton transfer reaction time-of-flight mass spectrometry (PTR-ToF-MS): towards a real-time process control for a consistent roast profile.

PubMed

Wieland, Flurin; Gloess, Alexia N; Keller, Marco; Wetzel, Andreas; Schenker, Stefan; Yeretzian, Chahan

2012-03-01

A real-time automated process control tool for coffee roasting is presented to consistently and accurately achieve a targeted roast degree. It is based on the online monitoring of volatile organic compounds (VOC) in the off-gas of a drum roaster by proton transfer reaction time-of-flight mass spectrometry at a high time (1 Hz) and mass resolution (5,500 m/Δm at full width at half-maximum) and high sensitivity (better than parts per billion by volume). Forty-two roasting experiments were performed with the drum roaster being operated either on a low, medium or high hot-air inlet temperature (= energy input) and the coffee (Arabica from Antigua, Guatemala) being roasted to low, medium or dark roast degrees. A principal component analysis (PCA) discriminated, for each one of the three hot-air inlet temperatures, the roast degree with a resolution of better than ±1 Colorette. The 3D space of the three first principal components was defined based on 23 mass spectral profiles of VOCs and their roast degree at the end point of roasting. This provided a very detailed picture of the evolution of the roasting process and allowed establishment of a predictive model that projects the online-monitored VOC profile of the roaster off-gas in real time onto the PCA space defined by the calibration process and, ultimately, to control the coffee roasting process so as to achieve a target roast degree and a consistent roasting.

8. VIEW TO SOUTHEAST, DRYERS, GRINDING/ROD MILL, MECHANIC SHED, AND ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

8. VIEW TO SOUTHEAST, DRYERS, GRINDING/ROD MILL, MECHANIC SHED, AND SKINNER SALT ROASTERS. - Vanadium Corporation of America (VCA) Naturita Mill, 3 miles Northwest of Naturita, between Highway 141 & San Miguel River, Naturita, Montrose County, CO

3. VIEW TO NORTHEAST, MECHANIC SHED, DRYERS, GRINDING/ROD MILL, AND ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

3. VIEW TO NORTHEAST, MECHANIC SHED, DRYERS, GRINDING/ROD MILL, AND SKINNER SALT ROASTERS. - Vanadium Corporation of America (VCA) Naturita Mill, 3 miles Northwest of Naturita, between Highway 141 & San Miguel River, Naturita, Montrose County, CO

3. Right side of Zinc Plant, from Cell Room midpoint ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

3. Right side of Zinc Plant, from Cell Room midpoint to Plant Office (foreground) and #5 Roaster and Concentrate Handling (background). View is to the east. - Sullivan Electrolytic Zinc Plant, Government Gulch, Kellogg, Shoshone County, ID

A novel method for a multi-level hierarchical composite with brick-and-mortar structure

PubMed Central

Brandt, Kristina; Wolff, Michael F. H.; Salikov, Vitalij; Heinrich, Stefan; Schneider, Gerold A.

2013-01-01

The fascination for hierarchically structured hard tissues such as enamel or nacre arises from their unique structure-properties-relationship. During the last decades this numerously motivated the synthesis of composites, mimicking the brick-and-mortar structure of nacre. However, there is still a lack in synthetic engineering materials displaying a true hierarchical structure. Here, we present a novel multi-step processing route for anisotropic 2-level hierarchical composites by combining different coating techniques on different length scales. It comprises polymer-encapsulated ceramic particles as building blocks for the first level, followed by spouted bed spray granulation for a second level, and finally directional hot pressing to anisotropically consolidate the composite. The microstructure achieved reveals a brick-and-mortar hierarchical structure with distinct, however not yet optimized mechanical properties on each level. It opens up a completely new processing route for the synthesis of multi-level hierarchically structured composites, giving prospects to multi-functional structure-properties relationships. PMID:23900554

A novel method for a multi-level hierarchical composite with brick-and-mortar structure.

PubMed

Brandt, Kristina; Wolff, Michael F H; Salikov, Vitalij; Heinrich, Stefan; Schneider, Gerold A

2013-01-01

The fascination for hierarchically structured hard tissues such as enamel or nacre arises from their unique structure-properties-relationship. During the last decades this numerously motivated the synthesis of composites, mimicking the brick-and-mortar structure of nacre. However, there is still a lack in synthetic engineering materials displaying a true hierarchical structure. Here, we present a novel multi-step processing route for anisotropic 2-level hierarchical composites by combining different coating techniques on different length scales. It comprises polymer-encapsulated ceramic particles as building blocks for the first level, followed by spouted bed spray granulation for a second level, and finally directional hot pressing to anisotropically consolidate the composite. The microstructure achieved reveals a brick-and-mortar hierarchical structure with distinct, however not yet optimized mechanical properties on each level. It opens up a completely new processing route for the synthesis of multi-level hierarchically structured composites, giving prospects to multi-functional structure-properties relationships.

A novel method for a multi-level hierarchical composite with brick-and-mortar structure

NASA Astrophysics Data System (ADS)

Brandt, Kristina; Wolff, Michael F. H.; Salikov, Vitalij; Heinrich, Stefan; Schneider, Gerold A.

2013-07-01

The fascination for hierarchically structured hard tissues such as enamel or nacre arises from their unique structure-properties-relationship. During the last decades this numerously motivated the synthesis of composites, mimicking the brick-and-mortar structure of nacre. However, there is still a lack in synthetic engineering materials displaying a true hierarchical structure. Here, we present a novel multi-step processing route for anisotropic 2-level hierarchical composites by combining different coating techniques on different length scales. It comprises polymer-encapsulated ceramic particles as building blocks for the first level, followed by spouted bed spray granulation for a second level, and finally directional hot pressing to anisotropically consolidate the composite. The microstructure achieved reveals a brick-and-mortar hierarchical structure with distinct, however not yet optimized mechanical properties on each level. It opens up a completely new processing route for the synthesis of multi-level hierarchically structured composites, giving prospects to multi-functional structure-properties relationships.

Production of dried shrimp mixed with turmeric and salt by Spouted Bed technique enter the rectangular chamber.

NASA Astrophysics Data System (ADS)

Thanthong, P.; Mustafa, Y.; Ngamrungroj, D.

2017-09-01

Today, dried shrimp in the market were refused food colour and drying until shrimp are colourful and tasty. Meanwhile, Community groups, women’s health trying to produce food products come from herbs. As an alternative to consumers. The production process is also a traditional way to dry. In order to extend the shelf life longer. Sometimes, potential risks, both in quality and quantity of products. As a result, consumers are enormous. Thus, this research aims to study the possibility to produce shrimp dried mixed with turmeric and salt. Then dried shrimp mixed with turmeric and salt to keep up the quality criteria of the Food and Drug Administration-FDA It can reduce the risk of the consumer and can keep up in a kitchen Thailand. When buying shrimp from the fisherman’s boat Will be made clear, clean impurities and shaking the sand to dry. Prepare a mixture of turmeric and salt. The shrimp were dipped into a beef with stirrer for 3 minutes. And scoop up centrifugal shrimp with dried. Measurement of initial moisture content averaging 78%wb. Then drying technique Spouted enter the rectangular chamber a continuous manner. Until average moisture content to 17%wb. The air temperature in the drying chamber at 180 °C and hot air speed 4.5 m/s, a state heat transfer Mass and moisture within the shrimp. In chamber when drying, the shrimp have moved freely behaviour can spit water out faster does not burn. Shaving legs of shrimp shell fragments lightweight is sorting out the top of drying chamber. Private shrimp were dried out to the front of the quad drying chamber. Power consumption 27.5 MJ/kg, divided into electrical energy 12.3 MJ/kg and thermal energy is 15.2 MJ/kg. The hot air comes from burning LPG gas burner with dual automatic. And can adjustable to room temperature drying characteristics modulation setting.

40 CFR 372.3 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., roasters, and foundry furnaces). (8) Titanium dioxide chloride process oxidation reactors. (9) Methane... sulfur values from spent sulfuric acid. (12) Halogen acid furnaces (HAFs) for the production of acid from halogenated hazardous waste generated by chemical production facilities where the furnace is located on the...

40 CFR 372.3 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., roasters, and foundry furnaces). (8) Titanium dioxide chloride process oxidation reactors. (9) Methane... sulfur values from spent sulfuric acid. (12) Halogen acid furnaces (HAFs) for the production of acid from halogenated hazardous waste generated by chemical production facilities where the furnace is located on the...

Exploratory drilling in the Prairie du Chien group of the Wisconsin zinc-lead districts by the U.S. Geological Survey in 1949-1950

USGS Publications Warehouse

Heyl, Allen Van; Lyons, Erwin J.; Agnew, Allen F.

1951-01-01

The U. S. Geological Survey in cooperation with the Wisconsin Geological and Natural History Survey explored the Prairie du Chien group in the main productive area of the Wisconsin zinc-lead district during 1949-50. Eight properties--Crow Branch diggings, Leix, Harris, Spitzbarth, Kennedy, James, Raisbeck and Vinegar Hill Roaster--were explored using both diamond and churn drills. Twenty holes were drilled that totaled 8,582 feet in depth. The objectives of the exploration were to determine if the Prairie du Chien and other formations below the principal ore-bearing strata (Galena, Decorah, and Platteville formations) of the district are favorable for ore deposits, and to determine the type of ore deposits, if present. Lean deposits of sphalerite, marcasite, and pyrite were found in the Prairie du Chien on five properties--Crow Branch, Leix, Harris, Spitzbarth, and Vinegar Hill 1%ouster-and also in the Franconia sandstone on the Leix property. In the drilled area the sulfides in the Prairie du Chien group occur in certain more brittle or soluble dolomite beds that contain cavities formed by brecciation or solution.

Manual sorting to eliminate aflatoxin from peanuts.

PubMed

Galvez, F C F; Francisco, M L D L; Villarino, B J; Lustre, A O; Resurreccion, A V A

2003-10-01

A manual sorting procedure was developed to eliminate aflatoxin contamination from peanuts. The efficiency of the sorting process in eliminating aflatoxin-contaminated kernels from lots of raw peanuts was verified. The blanching of 20 kg of peanuts at 140 degrees C for 25 min in preheated roasters facilitated the manual sorting of aflatoxin-contaminated kernels after deskinning. The manual sorting of raw materials with initially high aflatoxin contents (300 ppb) resulted in aflatoxin-free peanuts (i.e., peanuts in which no aflatoxin was detected). Verification procedures showed that the sorted sound peanuts contained no aflatoxin or contained low levels (<15 ppb) of aflatoxin. The results obtained confirmed that the sorting process was effective in separating contaminated peanuts whether or nor contamination was extensive. At the commercial level, when roasters were not preheated, the dry blanching of 50 kg of peanuts for 45 to 55 min facilitated the proper deskinning and subsequent manual sorting of aflatoxin-contaminated peanut kernels from sound kernels.

CHARACTERIZATION AND PH/EH-BASED LEACHING TESTS OF MINING WASTES CONTAINING MERCURY

EPA Science Inventory

This study was undertaken as a part of developing treatment alternatives for waste materials, primarily waste rock and roaster tailings, from sites contaminated with mercury (Hg) mining wastes. Leaching profiles of waste rock over a range of different pH and oxidation-reduction (...

CHARACTERIZATION AND PH/EH-BASED LEACHING TESTS OF MINING WASTES CONTAINING MERCURY

EPA Science Inventory

This study was undertaken as a part of developing treatment alternatives for waste materials, primarily waste rock and roaster tailings, from sites contaminated with Mercury (Hg) mining wastes. Leaching profiles of waste rock over a range of different pH and oxidation-reduction ...

Peanut Roaster Temperatures Relative to Salmonella Kill

USDA-ARS?s Scientific Manuscript database

ARS, Market Quality and Handling Research Unit, Raleigh NC 27695 In response to the limited peanut butter contamination incident of 2006/7, studies were initiated to examine the effect of various time and temperature protocols on log kill levels for Salmonella on peanuts. The objective of the work ...

40 CFR 60.170 - Applicability and designation of affected facility.

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Primary Zinc Smelters § 60.170 Applicability and designation of affected facility. (a) The...: roaster and sintering machine. (b) Any facility under paragraph (a) of this section that commences...

49. VIEW FROM WEST OF DUST COLLECTOR BLOWER LOCATED AT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

49. VIEW FROM WEST OF DUST COLLECTOR BLOWER LOCATED AT CRUSHED OXIDIZED ORE BIN FEED LEVEL. THE ROASTER IS BEYOND AND THE MACHINE SHOP IS ON THE TRAM TERRACE, UPPER RIGHT. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

III. Co-electrodeposition/removal of copper and nickel in a spouted electrochemical reactor.

PubMed

Grimshaw, Pengpeng; Calo, Joseph M; Hradil, George

2011-07-11

Results are presented of an investigation of co-electrodeposition of copper and nickel from acidic solution mixtures in a cylindrical spouted electrochemical reactor. The effects of solution pH, temperature, and applied current on metal removal/recovery rate, current efficiency, and corrosion of the deposited metals from the cathodic particles were examined under galvanostatic operation. The quantitative and qualitative behavior of co-electrodeposition of the two metals from their mixtures differs significantly from that of the individual single metal solutions. This is primarily attributed to the metal displacement reaction between Ni(0) and Cu(2+). This reaction effectively reduces copper corrosion, and amplifies that for nickel (at least at high concentrations). It also amplifies the separation of the deposition regimes of the two metals in time, which indicates that the recovery of each metal as a relatively pure deposit from the mixture is possible. It was also shown that nitrogen sparging considerably increases the observed net electrodeposition rates for both metals - considerably more so than from solutions with just the single metals alone. A numerical model of co-electrodeposition, corrosion, metal displacement, and mass transfer in the cylindrical spouted electrochemical reactor is presented that describes the behavior of the experimental copper and nickel removal data quite well.

III. Co-electrodeposition/removal of copper and nickel in a spouted electrochemical reactor

PubMed Central

Grimshaw, Pengpeng; Calo, Joseph M.; Hradil, George

2011-01-01

Results are presented of an investigation of co-electrodeposition of copper and nickel from acidic solution mixtures in a cylindrical spouted electrochemical reactor. The effects of solution pH, temperature, and applied current on metal removal/recovery rate, current efficiency, and corrosion of the deposited metals from the cathodic particles were examined under galvanostatic operation. The quantitative and qualitative behavior of co-electrodeposition of the two metals from their mixtures differs significantly from that of the individual single metal solutions. This is primarily attributed to the metal displacement reaction between Ni0 and Cu2+. This reaction effectively reduces copper corrosion, and amplifies that for nickel (at least at high concentrations). It also amplifies the separation of the deposition regimes of the two metals in time, which indicates that the recovery of each metal as a relatively pure deposit from the mixture is possible. It was also shown that nitrogen sparging considerably increases the observed net electrodeposition rates for both metals – considerably more so than from solutions with just the single metals alone. A numerical model of co-electrodeposition, corrosion, metal displacement, and mass transfer in the cylindrical spouted electrochemical reactor is presented that describes the behavior of the experimental copper and nickel removal data quite well. PMID:21874093

CHARACTERIZATION AND EH/PH-BASED LEACHING TESTS OF MERCURY-CONTAINING MINING WASTES FROM THE SULFUR BANK MERCURY MINE, LAKE COUNTY, CALIFORNIA

EPA Science Inventory

Mine waste rock and roaster tailings were collected from the Sulfur Bank Mercury Mine (SBMM) located in Clearlake Oaks, California. The site has been under investigation as a Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) site. Leaching profiles o...

INFLUENCE OF PH AND OXIDATION-REDUCTION (EH) POTENTIAL ON THE DISSOLUTION OF MERCURY-CONTAINING MINE WASTES FROM THE SULFUR BANK MERCURY MINE

EPA Science Inventory

Mine waste rock and roaster tailings were collected from the Sulfur Bank Mercury Mine (SBMM) located in Clearlake Oaks, California. The site has been under investigation as a Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) site. Characterization an...

21 CFR 558.365 - Nequinate.

Code of Federal Regulations, 2010 CFR

2010-04-01

... used as follows: (1) Broiler or fryer chickens—(i) Amount per ton. Nequinate, 18.16 grams. (ii...) Roaster chickens or replacement chickens for caged layers—(i) Amount per ton. Nequinate, 18.16 grams (0... continuously as the sole ration; do not feed to chickens over 16 weeks of age. [40 FR 13959, Mar. 27, 1975, as...

40 CFR 60.173 - Standard for sulfur dioxide.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Standard for sulfur dioxide. 60.173... Smelters § 60.173 Standard for sulfur dioxide. (a) On and after the date on which the performance test... subpart shall cause to be discharged into the atmosphere from any roaster any gases which contain sulfur...

40 CFR 60.173 - Standard for sulfur dioxide.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false Standard for sulfur dioxide. 60.173... Smelters § 60.173 Standard for sulfur dioxide. (a) On and after the date on which the performance test... subpart shall cause to be discharged into the atmosphere from any roaster any gases which contain sulfur...

40 CFR 60.173 - Standard for sulfur dioxide.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Standard for sulfur dioxide. 60.173... Smelters § 60.173 Standard for sulfur dioxide. (a) On and after the date on which the performance test... subpart shall cause to be discharged into the atmosphere from any roaster any gases which contain sulfur...

40 CFR 60.173 - Standard for sulfur dioxide.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standard for sulfur dioxide. 60.173... Smelters § 60.173 Standard for sulfur dioxide. (a) On and after the date on which the performance test... subpart shall cause to be discharged into the atmosphere from any roaster any gases which contain sulfur...

Mountain Plains Learning Experience Guide: Appliance Repair. Course: Heater-Type Appliances.

ERIC Educational Resources Information Center

Ziller, T.

One of two individualized courses included in an appliance repair curriculum (see CE 027 767), this course covers minor and major heater-type appliances. The course is comprised of six units: (1) Irons, (2) Roasters, (3) Space Heaters, (4) Water Heaters, (5) Electric Ranges, and (6) Gas Ranges. Each unit begins with a Unit Learning Experience…

INFLUENCE OF PH AND OXIDATION-REDUCTION POTENTIAL (EH) ON THE DISSOLUTION OF MERCURY-CONTAINING MINE WASTES FROM THE SULFUR BANK MERCURY MINE

EPA Science Inventory

This study was undertaken as a part of developing treatment alternatives for waste materials, primarily waste rock and roaster tailings, from sites contaminated with mercury (Hg) mining wastes. Leaching profiles of waste rock over a range of different pH and oxidation-reduction (...

The role of gravity in the nutrition and formation of Bacillus colonies

NASA Astrophysics Data System (ADS)

Puzyr, A.; Tirranen, L.; Krylova, T.

The soil-like substrate is used to cultivate higher plants in man-made closed ecosystems. It allows increasing the closeness of the systems and decreasing the plant solid residues and human wastes. Unusual funnel-shaped bacterial colonies of Bacillus species have been observed during analysis of microflora of plant nutritional solution. The colonies have the following characteristics: a) the diameter of "funnel socket" (the biomass contacting with nutritional agar) is 10.0-15.0 mm; b) the thickness of "funnel socket" is 0.5-2.5 mm; c) the diameter of the middle part of the "funnel spout" (the biomass contacting with the gas phase) is 1,0-1,5 mm; d) the length of the "funnel spout" is 10.0-15.0 mm. In the socket and the middle part of the "funnel spout" there is a gas cavity which is most probably formed by bacterial gas metabolites. It has been shown that: i) the surface of these funnel-shaped colonies of Bacillus species is hydrophobic, as is the surface of other Bacillus species ( . brevis, B. cellulomonos, B. flavus, B.B formosus, B. subtilis); ii) the forms of colonies can be changed by varying the position of the growing biomass in relation to the gravitation forces. The experiment proved that the form of the "funnel sockets" and the length of the "funnel spouts" of the colonies are determined by hydrophobic air-contacting surface layer, which does not leak and stretches under the weight of accumulated water. A hypothesis has been suggested that the gravity force plays the role of a "pump" supplying and holding water within the colony. Thus, the water that comes under the gravity force contains dissolved nutrients and bacterial cells in the hydrophobic layer. These cells that are situated far away from the nutrient agar have no nutrient deficiency. The water accumulated by the colonies might be free water of agar media or it can be produced by metabolic disruption of medium fat. Hence, when growing a colony in agar media the water-soluble nutrient substances enter the growing colonies not only due to diffusion processes but also with the directional water flow under the gravity force.

Hydrogen Production by Sorption Enhanced Steam Reforming (SESR) of Biomass in a Fluidised-Bed Reactor Using Combined Multifunctional Particles

PubMed Central

Zheng, Liya; Zhang, Zili; Fennell, Paul S.

2018-01-01

The performance of combined CO2-sorbent/catalyst particles for sorption enhanced steam reforming (SESR), prepared via a simple mechanical mixing protocol, was studied using a spout-fluidised bed reactor capable of continuous solid fuel (biomass) feeding. The influence of particle size (300–500 and 710–1000 µm), CaO loading (60–100 wt %), Ni-loading (10–40 wt %) and presence of dicalcium silicate support (22.6 wt %) on SESR process performance were investigated. The combined particles were characterised by their density, porosity and CO2 carrying capacity with the analysis by thermogravimetric analysis (TGA), Brunauer-Emmett-Teller (BET), Barrett-Joyner-Halenda (BJH) and mercury intrusion porosimetry (MIP). All experiments were conducted with continuous oak biomass feeding at a rate of 0.9 g/min ± 10%, and the reactor was operated at 660 ± 5 °C, 1 atm and 20 ± 2 vol % steam which corresponds to a steam-to-carbon ratio of 1.2:1. Unsupported combined particles containing 21.0 wt % Ni and 79 wt % CaO were the best performing sorbent/catalyst particle screened in this study, when accounting for the cost of Ni and the improvement in H2 produced by high Ni content particles. SESR tests with these combined particles produced 61 mmol H2/gbiomass (122 g H2/kgbiomass) at a purity of 61 vol %. Significant coke formation within the feeding tube and on the surfaces of the particles was observed which was attributed to the low steam to carbon ratio utilised. PMID:29883427

Development of advanced, continuous mild gasification process for the production of co-products

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ness, R.O. Jr.; Aulich, T.R.

1991-05-01

The current objective of the University of North Dakota Energy and Environmental Research Center (EERC) mild gasification project is to optimize reaction char and marketable liquids production on a 100-lb/hr scale using Wyodak subbituminous and Indiana No. 3 bituminous coals. Tests performed using the EERC 100-lb/hr process development unit (PDU) include a refractory-cure (Test P001), a test using petroleum coke (Test P002), and tests using Wyodak and Indiana coals. The reactor system used for the 11 PDU tests conducted to date consists of a spouted, fluid-bed carbonizer equipped with an on-line condensation train that yields three boiling point fractions ofmore » coal liquids ranging in volatility from about (77{degrees}--750{degrees}F) (25{degrees}--400{degrees}C). The September--December 1990 quarterly report described reaction conditions and the bulk of the analytical results for Tests P010 and P011. This report describes further P010 and P011 analytical work, including the generation of simulated distillation curves for liquid samples on the basis of sulfur content, using gas chromatography coupled with atomic emission detection (GC/AED) analysis. 13 figs., 3 tabs.« less

Validation of analytical conditions for determination of polycyclic aromatic hydrocarbons in roasted coffee by gas chromatography-mass spectrometry.

PubMed

Guatemala-Morales, Guadalupe María; Beltrán-Medina, Elisa Alejandra; Murillo-Tovar, Mario Alfonso; Ruiz-Palomino, Priscilla; Corona-González, Rosa Isela; Arriola-Guevara, Enrique

2016-04-15

Polycyclic aromatic hydrocarbons (PAHs) are of significant interest due to their genotoxicity in humans. PAHs quantification in coffee is complex since some of its compounds interfere in the chromatographic analysis, which hinders the reliable determination of the PAHs. Analytical conditions for the ultrasound extraction, purification and quantification of 16 PAHs in roasted coffee were studied. The better extraction efficiency of benzo[a]pyrene (68%) from ground-roasted coffee was achieved with a solvent ratio of Hex:MC (9:1 v/v) and three extraction periods of 20 min, followed by alkaline saponification and purification of the extracts. The detection limits were 0.85-39.32 ng mL(-1), and the quantification limits from 2.84 to 131.05 ng mL(-1), obtained for fluoranthene and chrysene, respectively. The extraction was effective for most of the analytes, with recoveries of 39.8% dibenzo[ah]anthracene and 69.0% benzo[b]fluoranthene. For coffee roasted in a spouted bed reactor, the summation of the 16 PAHs ranged from 3.5 to 16.4 μg kg(-1). Copyright © 2015 Elsevier Ltd. All rights reserved.

Bath and Shower Diverter Notice of Intent

EPA Pesticide Factsheets

An often-overlooked source of wasted water, many bath and shower diverters continuously leak a small amount of water from the tub spout while they are engaged, and water is being diverted from the bathtub to the showerhead.

CRYOGENIC DEWAR

DOEpatents

Chamberlain, W.H.; Maseck, H.E.

1964-01-28

This patent relates to a dewar for storing cryogenic gase and is of the type having aii inner flask surrounded by a vacuum jacket and having a vent spout through which evaporating gas escapes. Heretofore substantial gas loss has resulted from the radiation of heat towards the flask from the warmer outer elements of the dewar. In this invention, the mask is surrounded by a thermally conducting shield which is disposed in the vacuum space between the flask and the outer elements of the dewar. The shield contacts only the vent spout, which is cooled by the evaporating gas, and thus is maintained at a temperature very close to that of the flask itself. Accordingly, heat radiated toward the flask is intercepted and conducted to the evaporating gas rather than being re-radiated towards the hask. In a liquid helium dewar of typical configniration the mention reduces the boil-off rate by approximately one-half.(AEC)

Corrugated pipe adhesive applicator apparatus

DOEpatents

Shirey, R.A.

1983-06-14

Apparatus for coating selected portions of the troughs of a corrugated pipe with an adhesive includes a support disposed within the pipe with a reservoir containing the adhesive disposed on the support. A pump, including a spout, is utilized for supplying the adhesive from the reservoir to a trough of the pipe. A rotatable applicator is supported on the support and contacts the trough of the pipe. The applicator itself is sized so as to fit within the trough, and contacts the adhesive in the trough and spreads the adhesive in the trough upon rotation. A trough shield, supported by the support and disposed in the path of rotation of the applicator, is utilized to prevent the applicator from contacting selected portions of the trough. A locator head is also disposed on the support and provides a way for aligning the spout, the applicator, and the trough shield with the trough. 4 figs.

4th floor sacking deck looking east from 1945 elevator to ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4th floor sacking deck looking east from 1945 elevator to 1913 elevator indicating spout used to load bulk grain into rail cars - Stewart Company Grain Elevator, 16 West Carson Street, Pittsburgh, Allegheny County, PA

Factors Affecting Elevated Arsenic and Methyl Mercury Concentrations in Small Shield Lakes Surrounding Gold Mines near the Yellowknife, NT, (Canada) Region

PubMed Central

Houben, Adam James; D’Onofrio, Rebecca; Kokelj, Steven V; Blais, Jules M

2016-01-01

Gold mines in the Yellowknife, NT, region—in particular, the Giant Mine—operated from 1949–99, releasing 237,000 tonnes of waste arsenic trioxide (As2O3) dust, among other compounds, from gold ore extraction and roasting processes. For the first time, we show the geospatial distribution of roaster-derived emissions of several chemical species beyond the mine property on otherwise undisturbed taiga shield lakes within a 25 km radius of the mine, 11 years after its closing. Additionally, we demonstrate that underlying bedrock is not a significant source for the elevated concentrations in overlying surface waters. Aquatic arsenic (As) concentrations are well above guidelines for drinking water (10 μg/L) and protection for aquatic life (5 μg/L), ranging up to 136 μg/L in lakes within 4 km from the mine, to 2.0 μg/L in lakes 24 km away. High conversion ratios of methyl mercury were shown in lakes near the roaster stack as well, with MeHg concentrations reaching 44% of total mercury. The risk of elevated exposures by these metals is significant, as many lakes used for recreation and fishing near the City of Yellowknife are within this radius of elevated As and methyl Hg concentrations. PMID:27050658

Mouse taste preference tests: why only two bottles?

PubMed

Tordoff, Michael G; Bachmanov, Alexander A

2003-05-01

Two-bottle tests have been used extensively to measure the preference for taste and nutrient solutions but there has been little work with tests involving more than two bottles. Here, we compare the results obtained in two-bottle tests with those obtained in three- and six-bottle tests. In Experiment 1, we measured the preferences for 2 mM saccharin, 50 mM citric acid, 0.3 mM quinine hydrochloride and 75 mM NaCl displayed by 129X1/SvJ (129) and C57BL/6J (B6) mice. Mice drank more taste solution when they received two bottles providing taste solution and one providing water than when they received either a standard two-bottle test or two bottles providing water and one providing taste solution. The three-bottle tests also revealed the left spout side preferences of the 129 strain and were generally better at distinguishing between the 129 and B6 strains (i.e. were more sensitive) than were the two-bottle tests. In Experiment 2, we measured intakes and preferences in tests with six bottles, with one, two, three, four or five containing 75 mM NaCl and the rest containing water. NaCl preferences were monotonically related to the number of NaCl spouts available. A follow-up experiment found similar results whether the index of ingestion was volume intakes or licks. This argues that spillage cannot account for the effect of spout number on taste solution intake. Together, the results suggest that (i) the number of bottles of taste solution and water has a profound influence on taste solution intake and preference, and (ii) three-bottle tests may be more sensitive than two-bottle tests in many circumstances.

Mouse Taste Preference Tests: Why Only Two Bottles?

PubMed Central

Tordoff, Michael G.; Bachmanov, Alexander A.

2008-01-01

Two-bottle tests have been used extensively to measure the preference for taste and nutrient solutions but there has been little work with tests involving more than two bottles. Here, we compare the results obtained in two-bottle tests with those obtained in three- and six-bottle tests. In Experiment 1, we measured the preferences for 2 mM saccharin, 50 mM citric acid, 0.3 mM quinine hydrochloride and 75 mM NaCl displayed by 129X1/SvJ (129) and C57BL/6J (B6) mice. Mice drank more taste solution when they received two bottles providing taste solution and one providing water than when they received either a standard two-bottle test or two bottles providing water and one providing taste solution. The three-bottle tests also revealed the left spout side preferences of the 129 strain and were generally better at distinguishing between the 129 and B6 strains (i.e. were more sensitive) than were the two-bottle tests. In Experiment 2, we measured intakes and preferences in tests with six bottles, with one, two, three, four or five containing 75 mM NaCl and the rest containing water. NaCl preferences were monotonically related to the number of NaCl spouts available. A follow-up experiment found similar results whether the index of ingestion was volume intakes or licks. This argues that spillage cannot account for the effect of spout number on taste solution intake. Together, the results suggest that (i) the number of bottles of taste solution and water has a profound influence on taste solution intake and preference, and (ii) three-bottle tests may be more sensitive than two-bottle tests in many circumstances. PMID:12771018

Atmospheric laser Doppler velocimetry - An overview

NASA Technical Reports Server (NTRS)

Bilbro, J. W.

1980-01-01

Research, development, and application of atmospheric laser Doppler velocimetry are overviewed. Consideration is given to operation principles of CO2 heterodyne systems. Global wind, pollution, V/STOL flow, and true airspeed measurements are outlined. Wind energy, dust devils, water spouts, tornadoes, and aircraft wake vortices are covered.

4th level of 1913 elevator indicating sacking scale, part of ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4th level of 1913 elevator indicating sacking scale, part of the bagging system and nate to the sewing machine. Discharge spout for the grain bin to the left - Stewart Company Grain Elevator, 16 West Carson Street, Pittsburgh, Allegheny County, PA

14. Interior view, grain tanks (bins). Barrel view of tunnel ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

14. Interior view, grain tanks (bins). Barrel view of tunnel for load-out belt conveyor system located below tanks. Square, numbered spouts gravity-feed grain from overhead bins onto belt. - Saint Anthony Elevator No. 3, 620 Malcom Avenue, Southeast, Minneapolis, Hennepin County, MN

Apparatus Review.

ERIC Educational Resources Information Center

Byrum, David L.

1982-01-01

Suggests uses for and possible adaptations of a set of semiflexible molecular models. Includes price and supplier information. Also suggests rubbing oil from human face/hands along the pouring lip of a beaker, allowing one to pour uniformly from the beaker spout and making the process as dripless as possible. (Author/JN)

22. GENERAL VIEW OF MILL FROM SOUTHEAST. PROMINENT ARE THE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

22. GENERAL VIEW OF MILL FROM SOUTHEAST. PROMINENT ARE THE 100-TON STEEL CRUSHED UNOXIDIZED ORE BIN, CENTER LEFT; STEPHENS-ADAMSON 15 TON/HR INCLINED BUCKET ELEVATOR IN FRONT OF THE STEEL ORE BIN; AND THE BAKER COOLER, LOWER RIGHT. THESE MACHINES AND OTHERS IN THE AREA WERE PART OF THE UNOXIDIZED ORE CIRCUIT. THE ROASTER IS OUT OF THE PICTURE TO THE RIGHT (EAST). - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

Willful Ignorance and the Death Knell of Critical Thought

ERIC Educational Resources Information Center

Rubin, Daniel Ian

2018-01-01

Independent, critical thought has never been more important in the United States. In the Age of Trump, political officials spout falsehoods called "alternative facts" as if they were on equal footing with researchable, scientific data. At the same time, an unquestioning populace engages in acts of "willful ignorance" on a daily…

Water Spout

ERIC Educational Resources Information Center

Greenslade, Thomas B., Jr.

2013-01-01

During the AAPT summer meeting at Creighton University in 2011, Vacek Miglus and I took pictures of early apparatus at the Creighton physics department. The apparatus in the left-hand picture, shown with the spigot closed, appeared to be a liquid-level device: the water level was the same in both the narrow tube and the flaring glass vase.…

Use of a Force Sensor in Archimedes' Principle Experiment, Determination of Buoyant Force and Acceleration Due To Gravity

NASA Astrophysics Data System (ADS)

Aurora, Tarlok

2013-04-01

In introductory physics, students verify Archimedes' principle by immersing an object in water in a container, with a side-spout to collect the displaced water, resulting in a large uncertainty, due to surface tension. A modified procedure was introduced, in which a plastic bucket is suspended from a force sensor, and an object hangs underneath the bucket. The object is immersed in water in a glass beaker (without any side spout), and the weight loss is measured with a computer-controlled force sensor. Instead of collecting the water displaced by the object, tap water was added to the bucket to compensate for the weight loss, and the Archimedes' principle was verified within less than a percent. With this apparatus, buoyant force was easily studied as a function of volume of displaced water; as well as a function of density of saline solution. By graphing buoyant force as a function of volume (or density of liquid), value of g was obtained from slope. Apparatus and sources of error will be discussed.

Microencapsulation of Islets of Langerhans via selective withdrawal to achieve immunoisolation

NASA Astrophysics Data System (ADS)

Wyman, Jason; Dillmore, Shannon; Murphy, William; Garfinkel, Marc; Mrksich, Milan; Nagel, Sidney

2004-03-01

Cohen phet al. [1] described how the selective-withdrawal geometry may be used to microencapsulate particles in thin coats whose thickness is independent of the size of the encapsulated particle. We have applied a modified version of this geometry to the microencapsulation of Islets of Langerhans for the purpose of immunoisolation. The Islets are initially placed in a polymer-containing aqueous solution which is then drawn up into a selective-withdrawal spout. As that spout breaks up, it leaves the Islets coated with the polymer solution. These coats are then photo-crosslinked leaving the Islets encapsulated in a hydrogel coating. This coating provides a semi-permeable membrane which allows for the diffusion of small molecules such as nutrients, glucose, and insulin, but which excludes larger proteins such as antibodies. If one can successfully microencapsulate 10^6 islets in uniform coats such as these, then one may transplant Islets without immuno-suppression as a treatment for Type-I Diabetes. We will discuss preliminary phin vitro results. [1] I. Cohen, H. Li, J. L. Hougland, M. Mrksich, and S. R. Nagel Science 292, 265-267 (2001).

Comparison of drying characteristic and uniformity of banana cubes dried by pulse-spouted microwave vacuum drying, freeze drying and microwave freeze drying.

PubMed

Jiang, Hao; Zhang, Min; Mujumdar, Arun S; Lim, Rui-Xin

2014-07-01

To overcome the flaws of high energy consumption of freeze drying (FD) and the non-uniform drying of microwave freeze drying (MFD), pulse-spouted microwave vacuum drying (PSMVD) was developed. The results showed that the drying time can be dramatically shortened if microwave was used as the heating source. In this experiment, both MFD and PSMVD could shorten drying time by 50% as compared to the FD process. Depending on the heating method, MFD and PSMVD dried banana cubes showed trends of expansion while FD dried samples demonstrated trends of shrinkage. Shrinkage also brought intensive structure and highest fracturability of all three samples dried by different methods. The residual ascorbic acid content of PSMVD dried samples can be as high as in FD dried samples, which were superior to MFD dried samples. The tests confirmed that PSMVD could bring about better drying uniformity than MFD. Besides, compared with traditional MFD, PSMVD can provide better extrinsic feature, and can bring about improved nutritional features because of the higher residual ascorbic acid content. © 2013 Society of Chemical Industry.

Glutamatergic transmission in the nucleus of the solitary tract modulates memory through influences on amygdala noradrenergic systems.

PubMed

Miyashita, Teiko; Williams, Cedric L

2002-02-01

The authors examined whether glutamate release from the vagus nerve onto the nucleus of the solitary tract (NTS) is one mechanism by which the vagus influences memory and neural activity in limbic structures. Rats trained to drink from a spout were given a footshock (0.35 mA) on Day 5 after approaching the spout. Phosphate-buffered saline or 5.0, 50.0, or 100.0 nmol/0.5 microl glutamate was then infused into the NTS. Glutamate (5.0 or 50.0 nmol) significantly enhanced memory on the retention test. In Experiment 2, this effect was attenuated by blocking noradrenergic receptors in the amygdala with propranolol (0.3 microg/0.5 microl). Experiment 3 used in vivo microdialysis to determine whether footshock plus glutamate (50.0 nmol) alters noradrenergic output in the amygdala. These treatments caused a significant and long-lasting increase in amygdala noradrenergic concentrations. The results indicate that glutamate may be one transmitter that conveys the effects of vagal activation on brain systems that process memory.

Operant licking for intragastric sugar infusions: differential reinforcing actions of glucose, sucrose and fructose in mice

PubMed Central

Sclafani, Anthony; Ackroff, Karen

2015-01-01

Intragastric (IG) flavor conditioning studies in rodents indicate that isocaloric sugar infusions differ in their reinforcing actions, with glucose and sucrose more potent than fructose. Here we determined if the sugars also differ in their ability to maintain operant self-administration by licking an empty spout for IG infusions. Food-restricted C57BL/6J mice were trained 1 h/day to lick a food-baited spout, which triggered IG infusions of 16% sucrose. In testing, the mice licked an empty spout, which triggered IG infusions of different sugars. Mice shifted from sucrose to 16% glucose increased dry licking, whereas mice shifted to 16% fructose rapidly reduced licking to low levels. Other mice shifted from sucrose to IG water reduced licking more slowly but reached the same low levels. Thus IG fructose, like water, is not reinforcing to hungry mice. The more rapid decline in licking induced by fructose may be due to the sugar's satiating effects. Further tests revealed that the Glucose mice increased their dry licking when shifted from 16% to 8% glucose, and reduced their dry licking when shifted to 32% glucose. This may reflect caloric regulation and/or differences in satiation. The Glucose mice did not maintain caloric intake when tested with different sugars. They self-infused less sugar when shifted from 16% glucose to 16% sucrose, and even more so when shifted to 16% fructose. Reduced sucrose self-administration may occur because the fructose component of the disaccharide reduces its reinforcing potency. FVB mice also reduced operant licking when tested with 16% fructose, yet learned to prefer a flavor paired with IG fructose. These data indicate that sugars differ substantially in their ability to support IG self-administration and flavor preference learning. The same post-oral reinforcement process appears to mediate operant licking and flavor learning, although flavor learning provides a more sensitive measure of sugar reinforcement. PMID:26485294

Flow Caster Produces Custom Alloy Magnetic Ribbon

NASA Image and Video Library

2016-12-21

NASA Glenn’s large-scale, 5 kg planar flow caster cools a vat of molten metallic alloy, producing a magnetic ribbon that spouts into a collection bin. The caster has the ability to produce a magnetized ribbon that measures up to one mile long and 50 mm wide to support NASA’s hybrid electric aircraft propulsion and power management work.

The Invisibility of Steam

ERIC Educational Resources Information Center

Greenslade, Thomas B., Jr.

2014-01-01

Almost everyone "knows" that steam is visible. After all, one can see the cloud of white issuing from the spout of a boiling tea kettle. In reality, steam is the gaseous phase of water and is invisible. What you see is light scattered from the tiny droplets of water that are the result of the condensation of the steam as its temperature…

40 CFR 52.2020 - Identification of plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to... Subchapter A—Portable Fuel Containers Section 130.101 Applicability 10/5/02 12/8/04, 69 FR 70893 (c)(229... for portable fuel containers and spill-proof spouts 10/5/02 12/8/04, 69 FR 70893 (c)(229). Section 130...

29 CFR 1917.49 - Spouts, chutes, hoppers, bins, and associated equipment.

Code of Federal Regulations, 2013 CFR

2013-07-01

... turned off, locked out and tagged. (3) The employee entering the bin wears a lifeline and safety harness... equipment to be used. The inspection shall include at least the eye bolts, wires, and sheaves. (2) Power... adjustments are made to a power shovel, wire, or associated equipment, the power supply to the shovel shall be...

29 CFR 1917.49 - Spouts, chutes, hoppers, bins, and associated equipment.

Code of Federal Regulations, 2012 CFR

2012-07-01

... turned off, locked out and tagged. (3) The employee entering the bin wears a lifeline and safety harness... equipment to be used. The inspection shall include at least the eye bolts, wires, and sheaves. (2) Power... adjustments are made to a power shovel, wire, or associated equipment, the power supply to the shovel shall be...

29 CFR 1917.49 - Spouts, chutes, hoppers, bins, and associated equipment.

Code of Federal Regulations, 2014 CFR

2014-07-01

... turned off, locked out and tagged. (3) The employee entering the bin wears a lifeline and safety harness... equipment to be used. The inspection shall include at least the eye bolts, wires, and sheaves. (2) Power... adjustments are made to a power shovel, wire, or associated equipment, the power supply to the shovel shall be...

When It Rains, It Pours

ERIC Educational Resources Information Center

Mills, Linda

2012-01-01

"It's raining, it's pouring, the old man is snoring!" "The itsy, bitsy spider crawled up the waterspout, down came the rain and washed the spider out. Out came the sun and dried up all the rain, and the itsy, bitsy spider went up the spout again." What do children's nursery rhymes have to do with the school library? The author begins by telling a…

29 CFR 1917.49 - Spouts, chutes, hoppers, bins, and associated equipment.

Code of Federal Regulations, 2010 CFR

2010-07-01

... the entry; and (2) The power supply to the equipment carrying the cargo to the bin shall be turned off... been notified of the entry; (2) The power supply to the equipment carrying the cargo to the bin is... adjustments are made to a power shovel, wire, or associated equipment, the power supply to the shovel shall be...

29 CFR 1917.49 - Spouts, chutes, hoppers, bins, and associated equipment.

Code of Federal Regulations, 2011 CFR

2011-07-01

... the entry; and (2) The power supply to the equipment carrying the cargo to the bin shall be turned off... been notified of the entry; (2) The power supply to the equipment carrying the cargo to the bin is... adjustments are made to a power shovel, wire, or associated equipment, the power supply to the shovel shall be...

Exploring the Thermal Limits of IR-Based Automatic Whale Detection

DTIC Science & Technology

2014-09-30

spouts during the northward humpback whale migration, which occurs annually rather close to shore near North Stradbroke Island, Queensland, Australia...with concurrent visual observations. APPROACH By obtaining continuous IR video footage during two successive northward humpback whale ... Whale Detection (ETAW) Olaf Boebel P.O. Box 120161 27515 Bremerhaven GERMANY phone: +49 (471) 4831-1879 fax: +49 (471) 4831-1797 email

Operation Reputation: How to Manage and Protect Your Institution's Online Image

ERIC Educational Resources Information Center

Fernandez, Kim

2009-01-01

In the past few years, the online world has changed. It seems everyone is suddenly on social media sites like Facebook, Twitter, and MySpace, and anyone who can string words together--and a few who can't--seem to have glommed onto blogs, spouting opinions into the cyberworld with abandon. Prospective students, parents, and alumni not only read…

Direct Behavioral Evidence for Retronasal Olfaction in Rats

PubMed Central

Gautam, Shree Hari; Verhagen, Justus V.

2012-01-01

The neuroscience of flavor perception is becoming increasingly important to understand abnormal feeding behaviors and associated chronic diseases such as obesity. Yet, flavor research has mainly depended on human subjects due to the lack of an animal model. A crucial step towards establishing an animal model of flavor research is to determine whether the animal uses the retronasal mode of olfaction, an essential element of flavor perception. We designed a go- no go behavioral task to test the rat's ability to detect and discriminate retronasal odorants. In this paradigm, tasteless aqueous solutions of odorants were licked by water-restricted head-fixed rats from a lick spout. Orthonasal contamination was avoided by employing a combination of a vacuum around the lick-spout and blowing clean air toward the nose. Flow models support the effectiveness of both approaches. The licked odorants were successfully discriminated by rats. Moreover, the tasteless odorant amyl acetate was reliably discriminated against pure distilled water in a concentration-dependent manner. The results from this retronasal odor discrimination task suggest that rats are capable of smelling retronasally. This direct behavioral evidence establishes the rat as a useful animal model for flavor research. PMID:22970305

Interfacial Dynamics of Condensing Vapor Bubbles in an Ultrasonic Acoustic Field

NASA Astrophysics Data System (ADS)

Boziuk, Thomas; Smith, Marc; Glezer, Ari

2016-11-01

Enhancement of vapor condensation in quiescent subcooled liquid using ultrasonic actuation is investigated experimentally. The vapor bubbles are formed by direct injection from a pressurized steam reservoir through nozzles of varying characteristic diameters, and are advected within an acoustic field of programmable intensity. While kHz-range acoustic actuation typically couples to capillary instability of the vapor-liquid interface, ultrasonic (MHz-range) actuation leads to the formation of a liquid spout that penetrates into the vapor bubble and significantly increases its surface area and therefore condensation rate. Focusing of the ultrasonic beam along the spout leads to ejection of small-scale droplets from that are propelled towards the vapor liquid interface and result in localized acceleration of the condensation. High-speed video of Schlieren images is used to investigate the effects of the ultrasonic actuation on the thermal boundary layer on the liquid side of the vapor-liquid interface and its effect on the condensation rate, and the liquid motion during condensation is investigated using high-magnification PIV measurements. High-speed image processing is used to assess the effect of the actuation on the dynamics and temporal variation in characteristic scale (and condensation rate) of the vapor bubbles.

Sound localization in common vampire bats: Acuity and use of the binaural time cue by a small mammal

PubMed Central

Heffner, Rickye S.; Koay, Gimseong; Heffner, Henry E.

2015-01-01

Passive sound-localization acuity and the ability to use binaural time and intensity cues were determined for the common vampire bat (Desmodus rotundus). The bats were tested using a conditioned suppression/avoidance procedure in which they drank defibrinated blood from a spout in the presence of sounds from their right, but stopped drinking (i.e., broke contact with the spout) whenever a sound came from their left, thereby avoiding a mild shock. The mean minimum audible angle for three bats for a 100-ms noise burst was 13.1°—within the range of thresholds for other bats and near the mean for mammals. Common vampire bats readily localized pure tones of 20 kHz and higher, indicating they could use interaural intensity-differences. They could also localize pure tones of 5 kHz and lower, thereby demonstrating the use of interaural time-differences, despite their very small maximum interaural distance of 60 μs. A comparison of the use of locus cues among mammals suggests several implications for the evolution of sound localization and its underlying anatomical and physiological mechanisms. PMID:25618037

Increase in Lead Concentration in the Drinking Water of an Animal Care Facility.

PubMed

Davidowitz, Bradley; Boehm, Kirk; Banovetz, Sandra; Binkley, Neil

1998-01-01

We report here the unexpected detection, and subsequent correction, of a problem that resulted in an increase in lead concentration in the drinking water of an animal research facility. At the initiation of a study, analysis of a water sample obtained from the drinking spout of an animal cage revealed a lead concentration nearly twice the Environmental Protection Agency's maximum acceptable concentration. Because the municipal water supply routinely had been tested and found to be free of lead, it was assumed that this contamination was within the animal care facility. It was hypothesized that the brass fitting connecting the drinking spout to a polyvinyl chloride (PVC) pipe was the source of contamination. Water samples were obtained hourly from 0700 to 1600 hours before and after replacement of the brass fitting with a PVC fitting. After this change, lead concentrations in all samples were within acceptable limits. Although blood lead concentrations were undetectable in 47 rhesus monkeys (Macaca mulatta) housed in the facility, subclinical lead toxicosis could have resulted and potentially complicated studies in which these monkeys were used. We recommend that the water supply of research facilities be monitored periodically.

Reexamination of effects of paraformaldehyde on tissues around tapholes in sugar maple trees

Treesearch

David R. Houston; J. Chris Fagan

1997-01-01

Pellets containing paraformaldehyde (PFA) are sometimes placed behind spouts in tapped sugar maples to prolong sapflow and increase the yield of sap used to make maple syrup.The practice is controversial because the chemical has been shown to promote decay and is reported to cause cambial dieback around tapholes.This study reexamined the effects of PFA on tapped sugar...

Variability of single bean coffee volatile compounds of Arabica and robusta roasted coffees analysed by SPME-GC-MS.

PubMed

Caporaso, Nicola; Whitworth, Martin B; Cui, Chenhao; Fisk, Ian D

2018-06-01

We report on the analysis of volatile compounds by SPME-GC-MS for individual roasted coffee beans. The aim was to understand the relative abundance and variability of volatile compounds between individual roasted coffee beans at constant roasting conditions. Twenty-five batches of Arabica and robusta species were sampled from 13 countries, and 10 single coffee beans randomly selected from each batch were individually roasted in a fluidised-bed roaster at 210 °C for 3 min. High variability (CV = 14.0-53.3%) of 50 volatile compounds in roasted coffee was obtained within batches (10 beans per batch). Phenols and heterocyclic nitrogen compounds generally had higher intra-batch variation, while ketones were the most uniform compounds (CV < 20%). The variation between batches was much higher, with the CV ranging from 15.6 to 179.3%. The highest variation was observed for 2,3-butanediol, 3-ethylpyridine and hexanal. It was also possible to build classification models based on geographical origin, obtaining 99.5% and 90.8% accuracy using LDA or MLR classifiers respectively, and classification between Arabica and robusta beans. These results give further insight into natural variation of coffee aroma and could be used to obtain higher quality and more consistent final products. Our results suggest that coffee volatile concentration is also influenced by other factors than simply the roasting degree, especially green coffee composition, which is in turn influenced by the coffee species, geographical origin, ripening stage and pre- and post-harvest processing. Copyright © 2018 The Authors. Published by Elsevier Ltd.. All rights reserved.

18TH Annual Meeting of the European Neuroscience Association.

DTIC Science & Technology

1996-01-01

propagation of ictal-like seizure activity oný the neocottex of anaesthetised rats in viva. Epileptifotot events in the Global cerebral isehemia in rats...for the study of stroke -related brain injury . Novel MR] techniques, 40 neurological patients suspected clinically to suffer from inherited...head injury . MRI scan of start, runway and goal chamber with 2 drinking indicates diffuse cerebral damage, with focal abnormality spouts. The goal had

Investigating the procedural variables that determine whether rats will display negative anticipatory contrast or positive induction.

PubMed

Weatherly, Jeffrey N; Nurnberger, Jeri T; Hanson, Brent C

2005-08-31

Previous studies have demonstrated that consumption of a low-valued food substance may decrease if access to a high-valued substance will soon be available (negative anticipatory contrast). Research has also demonstrated that responding for a low-valued reinforcer may increase if responding for a high-valued reinforcer will soon be possible (positive induction). The present experiment employed rats to respond in a procedure similar to that typically used to produce negative anticipatory contrast. The goal was to determine what factors contribute to when a contrast or an induction effect will occur. Based on previous research, the influence of auditory cues, temporal delays, food deprivation, and location of substance delivery were investigated. Auditory cues and temporal delays did little to influence whether subjects increased or decreased their consumption of 1% sucrose when access to 32% sucrose was upcoming. The appearance of contrast or induction was related to level of deprivation, with deprivation promoting induction. Which effect occurred also depended on whether subjects consumed the two substances from one spout in one location (induction) or from two different spouts in two different locations (contrast). The present results help identify the procedural link(s) between these two effects. They also provide insight to why positive induction may occur (i.e., higher-order place conditioning).

U.S. broiler housing ammonia emissions inventory

NASA Astrophysics Data System (ADS)

Gates, R. S.; Casey, K. D.; Wheeler, E. F.; Xin, H.; Pescatore, A. J.

Using recently published baseline ammonia emissions data for U.S. broiler chicken housing, we present a method of estimating their contribution to an annual ammonia budget that is different from that used by USEPA. Emission rate increases in a linear relationship with flock age from near zero at the start of the flock to a maximum at the end of the flock, 28-65 days later. Market weight of chickens raised for meat varies from "broilers" weighing about 2 kg to "roasters" weighing about 3 kg. Multiple flocks of birds are grown in a single house annually, with variable downtime to prepare the house between flocks. The method takes into account weight and number of chickens marketed. Uncertainty in baseline emissions estimates is used so that inventory estimates are provided with error estimates. The method also incorporates the condition of litter that birds are raised upon and the varying market weight of birds grown. Using 2003 USDA data on broiler production numbers, broiler housing is estimated to contribute 8.8-11.7 kT ammonia for new and built-up litter, respectively, in Kentucky and 240-324 kT ammonia for new and built-up litter, respectively, nationally. Results suggest that a 10% uncertainty in annual emission rate is expected for the market weight categories of broilers, heavy broilers, and roasters. A 27-47% reduction in annual housing emission rate is predicted if new rather than built-up litter were used for every flock. The estimating method can be adapted to other meat bird building emissions and future ammonia emission strategies, with suitable insertion of an age-dependent emission factor or slope into a predictive model equation. The method can be readily applied and is an alternative to that used by USEPA.

Controls on the Mobility of Antimony in Mine Waste from Three Deposit Types

NASA Astrophysics Data System (ADS)

Jamieson, H.; Radková, A. B.; Fawcett, S.

2017-12-01

Antimony can be considered both a critical metal and an environmental hazard, with a toxicity similar to arsenic. It is concentrated in stibnite deposits, but also present in polymetallic and precious metal ores, frequently accompanied by arsenic. We have studied the mineralogical controls on the mobility of antimony in three types of mine waste: stibnite tailings from an antimony mine, tetrahedrite-bearing waste rock from copper mining, and gold mine tailings and ore roaster waste. Our results demonstrate that the tendency of antimony to leach into the aqueous environment or remain sequestered in solid phases depends on the primary host minerals and conditions governing the precipitation of secondary antimony-hosting phases. In tailings at the Beaver Brook antimony mine in Newfoundland, Canada, stibnite oxidizes rapidly, and secondary minerals such as the relatively insoluble Sb-Fe tripuhyite-like phase and Sb-bearing goethite. However, under dry conditions, the most important secondary Sb host is the Mg-Sb hydroxide brandholzite, but this easily soluble mineral disappears when it rains. Antimony that was originally hosted in tetrahedrite, a complex multi-element sulfosalt, in the historic waste rock piles at Špania Dolina-Piesky, Slovakia, is not as mobile as Cu and As during weathering but reprecipiates to a mixture of tripuhyite and romeite. Finally, the original antimony-hosting minerals, both stibnite and sulphosalts, in the gold ore at Giant Mine, Yellowknife, Canada were completely destroyed during ore roasting. In tailings-contaminated sediments, antimony persists in roaster-generated iron oxide phases, except under reducing conditions where some of the antimony forms a Sb-S phase. The combined presence of antimony and arsenic in mine waste complicates risk assessment but in general, our findings suggest that antimony is less mobile than arsenic in the environment.

Evaluation of materials and surface treatments for the DWPF melter pour spout bellows protective liner

DOE Office of Scientific and Technical Information (OSTI.GOV)

Imrich, K.J.; Bickford, D.F.; Wicks, G.G.

1997-06-27

A study was undertaken to evaluate a variety of materials and coatings for the DWPF pour spout bellows liner. The intent was to identify materials that would minimize or eliminate adherence of glass on the bellows liner wall and help minimize possible pluggage during glass pouring operations in DWPF. Glass has been observed adhering to the current bellow`s liner, which is made of 304L stainless steel. Materials were identified which successfully allowed molten glass to hit these surfaces and not adhere. Results of this study suggest that if these materials are used in the pouring system glass could still fallmore » into the canister without appreciable plugging, even if an unstable glass stream is produced. The materials should next be evaluated under the most realistic DWPF conditions possible. Other findings of this study include the following: (1) increasing coupon thickness produced a favorable increase in the glass sticking temperature; (2) highly polished surfaces, with the exception of the oxygen-free copper coupon coated with Armoloy dense chromium, did not produce a significant improvement in the glass sticking temperature, increasing angle of contact of the coupon to the falling glass did not yield a significant performance improvement; (3) electroplating with gold and silver and various diffusion coatings did not produce a significant increase in the glass sticking temperature. However, they may provide added oxidation and corrosion resistance for copper and bronze liners. Boron nitride coatings delaminated immediately after contact with the molten glass.« less

Where does the waiting list begin? A short review of the dynamics and organization of modern waiting lists.

PubMed

Rotstein, Dalia L; Alter, David A

2006-06-01

Waiting for medical care is the by-product of system rationing, where demand exceeds supply. In this short report we expand on the conventional concept of the queue, by focusing on the regulation of demand and by incorporating a funnel and spout analogy. Real-world examples are used to illustrate the infancy of funnel or demand-side reform initiatives targeting the queue, and the suggestion is made that policy needs to address the concept of 'waiting' much earlier in the treatment cycle.

Proceedings of the Scientific Conference on Obscuration and Aerosol Research Held in Aberdeen Proving Ground, Maryland on 17-21 June 1985.

DTIC Science & Technology

1986-07-01

Aerosols:Science, Technoloy ..and Industrial Aplications . Els-!vier NY, 1984. T. H. Tsang and J. R. Brock. "On Cstwald ripening", in B.Y.H. Liu et al...of Small Glass Particles Spouted in Water", Ph.D. Thesis , Rensselaer Polytechnic Institute, Troy, NY (1982). Table I Comparison of Predicted and...carrier densities and mobilities of graphite, copper, and second stage AsF 5 compound. The carrier den- sity of graphite is very low (l carrier for 10 atoms

Energized Active Regions

NASA Image and Video Library

2017-06-02

A pair of relatively small (but frenetic) active regions rotated into view, spouting off numerous small flares and sweeping loops of plasma (May 31-June 2, 2017). At first, only the one active region was observed, but mid-way though the video clip a second one behind the first can be picked out. The dynamic regions were easily the most remarkable areas on the sun during this 42-hour period. The images were taken in a wavelength of extreme ultraviolet light. Movies are available at https://photojournal.jpl.nasa.gov/catalog/PIA21756

Drying based on temperature-detection-assisted control in microwave-assisted pulse-spouted vacuum drying.

PubMed

Cao, Xiaohuang; Zhang, Min; Qian, He; Mujumdar, Arun S

2017-06-01

An online temperature-detection-assisted control system of microwave-assisted pulse-spouted vacuum drying was newly developed. By using this system, temperature control can be automatically and continuously adjusted based on the detection of drying temperature and preset temperature. Various strategies for constant temperature control, linear temperature control and three-step temperature control were applied to drying carrot cubes. Drying kinetics and the quality of various temperature-controlled strategies online are evaluated for the new drying technology as well as its suitability as an alternative drying method. Drying time in 70 °C mode 1 had the shortest drying time and lowest energy consumption in all modes. A suitable colour, highest re-hydration ratio and fracture-hardness, and longest drying time occurred in 30-40-50 °C mode 3. The number of hot spots was reduced in 40-50-60 °C mode 3. Acceptable carrot snacks were obtained in 50-60-70 °C mode 3 and 70 °C mode 2. All temperature curves showed that the actual temperatures followed the preset temperatures appropriately. With this system, a linear temperature-controlled strategy and a three-step temperature-controlled strategy can improve product quality and heating non-uniformity compared to constant temperature control, but need greater energy consumption and longer drying time. A temperature-detection-assisted control system was developed for providing various drying strategies as a suitable alternative in making a snack product. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Bubbling in unbounded coflowing liquids.

PubMed

Gañán-Calvo, Alfonso M; Herrada, Miguel A; Garstecki, Piotr

2006-03-31

An investigation of the stability of low density and viscosity fluid jets and spouts in unbounded coflowing liquids is presented. A full parametrical analysis from low to high Weber and Reynolds numbers shows that the presence of any fluid of finite density and viscosity inside the hollow jet elicits a transition from an absolute to a convective instability at a finite value of the Weber number, for any value of the Reynolds number. Below that critical value of the Weber number, the absolute character of the instability leads to local breakup, and consequently to local bubbling. Experimental data support our model.

Crystal accumulation in the Hanford Waste Treatment Plant high level waste melter: Summary of 2017 experiments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fox, K.; Fowley, M.

A full-scale, transparent mock-up of the Hanford Tank Waste Treatment and Immobilization Project High Level Waste glass melter riser and pour spout has been constructed to allow for testing with visual feedback of particle settling, accumulation, and resuspension when operating with a controlled fraction of crystals in the glass melt. Room temperature operation with silicone oil and magnetite particles simulating molten glass and spinel crystals, respectively, allows for direct observation of flow patterns and settling patterns. The fluid and particle mixture is recycled within the system for each test.

Cacao usage by the earliest Maya civilization.

PubMed

Hurst, W Jeffrey; Tarka, Stanley M; Powis, Terry G; Valdez, Fred; Hester, Thomas R

2002-07-18

The Maya archaeological site at Colha in northern Belize, Central America, has yielded several spouted ceramic vessels that contain residues from the preparation of food and beverages. Here we analyse dry residue samples by using high-performance liquid chromatography coupled to atmospheric-pressure chemical-ionization mass spectrometry, and show that chocolate (Theobroma cacao) was consumed by the Preclassic Maya as early as 600 bc, pushing back the earliest chemical evidence of cacao use by some 1,000 years. Our application of this new and highly sensitive analytical technique could be extended to the identification of other ancient foods and beverages.

26. RW Meyer Sugar Mill: 18761889. Centrifugals, 1879, 1881. Manufacturer, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

26. RW Meyer Sugar Mill: 1876-1889. Centrifugals, 1879, 1881. Manufacturer, unknown. Supplied by Honolulu Ironworks, Honolulu, Hawaii, 1879, 1881. View: Historical view, 1934, from T. T. Waterman collection, Hawaiian Sugar Planters' Association. Once the molasses was separated from the sugar crystals it flowed through the spouts in the base of the centrifugals. The centrifugals' pulleys can be seen underneath the centrifugal. The centrifugal on the right has been reinforced with seven metal bands. The handles for the clutch mechanism are located above the centrifugal. - R. W. Meyer Sugar Mill, State Route 47, Kualapuu, Maui County, HI

Controls on the distribution of arsenic in lake sediments impacted by 65 years of gold ore processing in subarctic Canada: the role of organic matter

NASA Astrophysics Data System (ADS)

Galloway, Jennifer; Palmer, Michael; Swindles, Graeme T.; Sanei, Hamed; Jamieson, Heather E.; Parsons, Michael; Macumber, Andrew L.; Patterson, Tim; Falck, Hendrik

2017-04-01

Gold mines in the Yellowknife region of the Northwest Territories, Canada, operated from 1938 to 2003 and released approximately 20,000 tonnes of arsenic trioxide to the environment through stack emissions. This release resulted in highly elevated arsenic concentrations in lake surface waters and sediments relative to Canadian drinking water standards and guidelines for the protection of aquatic life. High northern latitudes are experiencing substantial impacts, including changes in bio-physico-chemical processes, due to climate change. Determining the affect of warming climate on contamination is complicated by the fact that little is known of climate change controls on As mobility and bioavailability. Further, while the role of dissolved organic matter in As cycling is relatively well characterized in soils and wetland sediments, few studies have investigated the role of solid organic matter in lacustrine systems. We use a meta-analytical approach to better understand controls on sedimentary arsenic distribution in lakes within a 50 km2 area of historic mineral processing activities. Arsenic concentrations in near surface sediments of the 100 lakes studied range from 5 mg/kg to over 10,000 mg/kg (median 81 mg/kg). Distance from the historical Giant Mine roaster stack and the amount of labile organic matter (S1 carbon as determined by Rock Eval pyrolysis) in lake sediments are the variables most strongly correlated with sedimentary As concentrations (Spearman's rank correlation As:distance from historic roaster rs=-0.57, p<0.05; As:S1 rs=0.55, p<0.05). The S1 fraction, volatile hydrocarbons derived from readily degradable geolipids and pigments predominantly originating from authochthonous organic matter, represents a small portion of the overall total organic carbon in the sedimentary material analyzed (median 2.33 wt.%). However, this fraction of organic matter has large potential to influence element concentrations in lake sediments through coating of pre-existing solid-phase As-mineral complexes, direct As-organic matter interactions, and promotion of microbial-mediated reduction and precipitation of As-bearing minerals.

Geyser preplay and eruption in a laboratory model with a bubble trap

NASA Astrophysics Data System (ADS)

Adelstein, Esther; Tran, Aaron; Saez, Carolina Muñoz; Shteinberg, Alexander; Manga, Michael

2014-09-01

We present visual observations and temperature measurements from a laboratory model of a geyser. Our model incorporates a bubble trap, a zone in which vapor can accumulate in the geyser's subsurface plumbing, in a vertical conduit connected to a basal chamber. Analogous features have been identified at several natural geysers. We observe three types of eruptions: 1) rising bubbles eject a small volume of liquid in a weak spout (small eruption); 2) boiling occurs in the conduit above the bubble trap (medium eruption); and 3) boiling occurs in the conduit and chamber (large eruption). In the last two cases, boiling in the conduit causes a rapid hydrostatic pressure drop that allows for the rise and eruption of liquid water in a vigorous spout. Boiling initiates at depth rather than propagating downward from the surface. In a single eruption cycle, multiple small eruptions precede every medium and large eruption. At least one eruption cycle that culminates in a medium eruption (i.e., a quiescent period followed by a series of small eruptions leading up to a medium eruption) precedes every eruption cycle that culminates in a large eruption. We find that the transfer of fluid with high enthalpy to the upper conduit during small and medium eruptions is necessary to heat the upper conduit and prepare the system for the full boiling required for a large eruption. The placement of the bubble trap midway up the conduit allows for more efficient heating of the upper conduit. Our model provides insight into the influence of conduit geometry on eruption style and the importance of heat transfer by smaller events in preparing the geyser system for eruption.

27. RW Meyer Sugar Mill: 18761889. Centrifugals, 1879, 1881. Manufacturer, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

27. RW Meyer Sugar Mill: 1876-1889. Centrifugals, 1879, 1881. Manufacturer, Unknown. Supplied by Honolulu Ironworks, Honolulu Hawaii, 1879, 1881. View: Historical view, 1934, from T.T. Waterman collection, Hawaiian Sugar Planters' Association. With the inner basket of the centrifugal revolving at 1200 rpm molasses flew outward from the granulated sugar, through the holes in the brass lining, and into the stationary outer basket. The molasses drained through the spout at the right and into molasses storage pits below the floor. The centrifugals were underdriven with a belt connected to the pulley beneath the basket. - R. W. Meyer Sugar Mill, State Route 47, Kualapuu, Maui County, HI

MSG intake and preference in mice are influenced by prior testing experience.

PubMed

Ackroff, Karen; Weintraub, Rachel; Sclafani, Anthony

2012-09-10

Monosodium glutamate (MSG), the prototypical umami substance, is used as a flavor enhancer in many foods, but when presented alone is often only weakly attractive. Yet with experience mice will develop strong preferences for MSG solution over water. The present experiments explored the conditions that change indifference to preference for MSG. C57BL/6J mice were given a series of 2-day two-bottle tests with water vs. an ascending series of MSG concentrations (0.1-450 mM) to assess preference and intake. Naive mice were indifferent to all concentrations, but following forced one-bottle exposure to 300 mM MSG they preferred most concentrations and consumed more MSG. Exposure to 100mM MSG also increased subsequent MSG preference but not intake. Experience with other nutritive solutions (8% sucrose, 8% Polycose, 8% casein hydrolysate, and isocaloric 3.5% soybean oil emulsion) also enhanced subsequent MSG preference and intake. Polycose and sucrose experience were almost as effective as MSG experience. However, not all sapid solutions were effective; 0.8% sucralose and 10mM MSG exposure did not alter subsequent MSG preference. The generality of the preexposure effect was tested by offering an ascending series (0.1-100 mM) of inosine monophosphate (IMP), another umami substance; initial indifference was converted to preference after forced exposure to 300 mM MSG. Together these results suggest that a combination of oral and post-oral effects may be responsible for the experience effect, with MSG itself the most potent stimulus. A final experiment revealed that MSG preference in naïve mice is enhanced by presenting the MSG and water drinking spouts far apart rather than side by side. Thus the preferences for umami solutions in mice are subject to influence from prior tastant experience as well spout position, which should be taken into account when studying acceptance of taste solutions in mice. Copyright © 2012 Elsevier Inc. All rights reserved.

1. Credit WCT. Original 2 1/4" x 2 1/4" color ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. Credit WCT. Original 2- 1/4" x 2- 1/4" color negative is housed in the JPL Photography Laboratory, Pasadena, California. This view shows the remote charge trimmer, a vertical lathe for turning propellant castings ("grain") in the front room of this structure. Ron Wright is shown in charge of the procedure; the hoist operator is unidentified. Grain for a BATES (Ballistic And Test Evaluation System) motor is being lowered into the lathe with a hoist and specially designed BATES fitting. The spout and waste barrel, in the foreground, collects waste trimmings for disposal (JPL negative no. JPL10286BC, 27 January 1989) - Jet Propulsion Laboratory Edwards Facility, Preparation Building, Edwards Air Force Base, Boron, Kern County, CA

Reviving the RNA World: An Insight into the Appearance of RNA Methyltransferases

PubMed Central

Rana, Ajay K.; Ankri, Serge

2016-01-01

RNA, the earliest genetic and catalytic molecule, has a relatively delicate and labile chemical structure, when compared to DNA. It is prone to be damaged by alkali, heat, nucleases, or stress conditions. One mechanism to protect RNA or DNA from damage is through site-specific methylation. Here, we propose that RNA methylation began prior to DNA methylation in the early forms of life evolving on Earth. In this article, the biochemical properties of some RNA methyltransferases (MTases), such as 2′-O-MTases (Rlml/RlmN), spOUT MTases and the NSun2 MTases are dissected for the insight they provide on the transition from an RNA world to our present RNA/DNA/protein world. PMID:27375676

Inhibition of return in the archer fish.

PubMed

Gabay, Shai; Leibovich, Tali; Ben-Simon, Avi; Henik, Avishai; Segev, Ronen

2013-01-01

Inhibition of return is the inhibitory tagging of recently attended locations or objects. It was previously suggested that inhibition of return is a foraging facilitator in visual search. Inhibition of return was first discovered in humans and was demonstrated also in monkeys, yet it has never been demonstrated in non-primates. Here we report the presence of inhibition of return in the archer fish, which shoots down prey on overhanging vegetation, using squirts of water spouted from its mouth. Moreover, we find similar attentional effects for fish as for human participants. Our results show that the generation of inhibition of return does not require a fully developed cortex and strengthen the view that inhibition of return functions as a foraging facilitator.

Oxidation Mechanism of Copper Selenide

NASA Astrophysics Data System (ADS)

Taskinen, Pekka; Patana, Sonja; Kobylin, Petri; Latostenmaa, Petri

2014-09-01

The oxidation mechanism of copper selenide was investigated at deselenization temperatures of copper refining anode slimes. The isothermal roasting of synthetic, massive copper selenide in flowing oxygen and oxygen - 20% sulfur dioxide mixtures at 450-550 °C indicate that in both atmospheres the mass of Cu2Se increases as a function of time, due to formation of copper selenite as an intermediate product. Copper selenide oxidises to copper oxides without formation of thick copper selenite scales, and a significant fraction of selenium is vaporized as SeO2(g). The oxidation product scales on Cu2Se are porous which allows transport of atmospheric oxygen to the reaction zone and selenium dioxide vapor to the surrounding gas. Predominance area diagrams of the copper-selenium system, constructed for selenium roasting conditions, indicate that the stable phase of copper in a selenium roaster gas with SO2 is the sulfate CuSO4. The cuprous oxide formed in decomposition of Cu2Se is further sulfated to CuSO4.

Gust-Front and Outflow Related Waterspouts: Timely Warnings, Formation, and Impact on Public Safety

NASA Astrophysics Data System (ADS)

Cappucci, M.

2013-12-01

Massachusetts may be over a thousand miles away from the traditional "tornado alley", but as the deadly tornadoes that killed four on June 1st 2011 proved, we are not immune to such storms. Over the course of half a century or so, Massachusetts has bore witness to scores of tornadoes, including an F5 twister that touched down on June 9th 1953, resulting in the death of 94 people. Since this tornado, none other in the United States had caused as many deaths, until the Joplin, Missouri catastrophe of May 22, 2011 (161 deaths). In Massachusetts, however, storms of such destructive magnitude are generally confined to the western half of the state, as the June 1, 2011 tornadoes in South Central Massachusetts illustrated. Despite this, a recently observed trend has revealed that the eastern Massachusetts coastline may boast as many, if not more, tornadoes, albeit undocumented. On June 23rd, 2012, a strong thunderstorm produced a spectacular gust front over Boston Harbor. This gust front was associated with intense thunderstorm outflow that helped to spawn a waterspout that roared ashore in Scituate as an EF-0 tornado. This waterspout, however, developed ahead of the gust front, yet merged with the cloud structure of the outflow, hinting at a type of interaction between the thunderstorm downdraft and the waterspout. This tornado caused minor damage. A similar situation occurred in Plymouth, MA, on July 24th, when three waterspouts formed ahead of the gust front of a severe thunderstorm; one of these tempests roared ashore on White Horse Beach as an EF-0 storm, causing minor damage to the sum of a few hundred dollars. Photos taken of these spouts reveal their formation ahead of the gust front, with a downdraft/waterspout interaction similar to the situation of June 23rd. Time-lapse videography of the gust front taken moments after the dissipation of the spouts reveals a horizontally oriented vortex a few hundred meters ahead of the storm's outflow boundary. The spinning of this vortex is likely caused by friction between the cooler air subducting behind the gust front against the warmer air ahead of the front. The vortex, on occasion, may be tilted onto a vertical axis by the warmer air ahead of the front; this same warm air now infiltrates the vertically-oriented vortex, thus being stretched, and forming a small waterspout. Because the waterspouts, however, are under the influence of the cool air from the thunderstorm downdraft, the spouts may move erratically before being upended. Because of the inability for NWS (National Weather Service) radar domes to detect the microscale circulation associated with such gust-front related waterspouts, forecasters at NWS offices in Massachusetts will now focus on the predecessors of waterspout formation. Among these tell-tale parameters is a well-pronounced gust-front moving over warm ocean waters, as well as a sharp, highly localized temperature contrast between the air ahead of and behind the gust front. When the NWS believes that conditions will favor the development of gust-front related waterspouts that may move onshore, a special statement will now be broadcast through the EAS system in Severe Thunderstorm Warnings. Mariners will benefit as well, with Special Marine Warnings advising caution on ';short-lived waterspouts'. Despite these alterations in NWS offices in Massachusetts, much has yet to be done to warn the public of the dangers associated with gust-front related waterspouts.

Dust in the wind: long range transport of dust in the atmosphere and its implications for global public and ecosystem health

USGS Publications Warehouse

Griffin, Dale W.; Kellogg, Christina A.; Shinn, Eugene A.

2001-01-01

Movement of soil particles in atmospheres is a normal planetary process. Images of Martian dust devils (wind-spouts) and dust storms captured by NASA's Pathfinder have demonstrated the significant role that storm activity plays in creating the red atmospheric haze of Mars. On Earth, desert soils moving in the atmosphere are responsible for the orange hues in brilliant sunrises and sunsets. In severe dust storm events, millions of tons of soil may be moved across great expanses of land and ocean. An emerging scientific interest in the process of soil transport in the Earth's atmosphere is in the field of public and ecosystem health. This article will address the benefits and the potential hazards associated with exposure to particle fallout as clouds of desert dust traverse the globe.

Using selective withdrawal to encapsulate pancreatic islets for immunoisolation

NASA Astrophysics Data System (ADS)

Wyman, Jason; Murphy, William; Mrksich, Milan

2005-11-01

We apply selective-withdrawal for encapsulating insulin-producing pancreatic islets within thin poly(ethylene glycol) (PEG) coats. Islets placed in an aqueous PEG solution are drawn into the selective-withdrawal spout which then breaks up, leaving the islets surrounded by a thin, 20μm, polymer coat. These coats, whose thickness is independent of the size of the encapsulated islet, are photo-crosslinked to form hydrogel capsules. We can apply multiple coats of varying chemical composition. These coats provide a semi-permeable membrane which allows the islets to respond to changes in glucose concentration by producing insulin in a manner similar to that of unencapsulated islets. Furthermore, the hydrogel capsules exclude large molecules the size of the smallest antibodies. Our results suggest that this microencapsulation technique may be useful for the transplantation of islets for treatment of Type I diabetes.

Cryogenic Cabaret

NASA Astrophysics Data System (ADS)

Leblanc, Marcel A. R.

2004-03-01

Recipient of the Royal Society of Canada's McNeil Medal for the promotion of science to the public,emeritus physics professor Marcel LeBlanc has given this spectacular science show to hundreds of audiences of students, parents, and science teachers over 35 years. An expert in cryophysics, Dr. LeBlanc chills his audience with a -78 C blizzard, freezes -200 C liquid nitrogen by boiling, morphs into a dragon spouting -200 C vapors, transforms soggy frozen cigars into torches. In the pursuit of science he sings low baritone then high tenor, fires electromagnetic cannons, and cannons belching smoke rings at the audience, invites teams to separate pairs of vacuum sealed hemispheres, levitates rings,magnets and electric coils,smashes rubber balls, explodes hydrogen balloons, and freezes everything but your imagination. For a preview glance at www.science.uottawa/phy/eng/profs/leblanc/ cryomagic: work in progress.

Breathe Plant, Breathe

NASA Astrophysics Data System (ADS)

Weiss, M.

2017-12-01

Some of the research that I have found is that plants with green oxygen produce the most oxygen.Green oxygen is the Some examples of plants like this are spouts (such as the sweet pea, buckwheat, and sunflower.) Some of the other plants are the snake plant and the areca plant. These three plants are most commonly used in households to produce more oxygen when needed. Looking at a few more websites I saw that the plants do not produce oxygen at night because they have no light to transfer within photosynthesis. Some other information that I got was that plants with thick leaves or have a lot of leaves on them produce more oxygen. Some examples of this are the peace lily and the bamboo palm. Since these plants have thick and big leaves they have more photosynthesis cells and can produce more oxygen.

Use of Temperature, Humidity, and Slaughter Condemnation Data to Predict Increases in Transport Losses in Three Classes of Swine and Resulting Foregone Revenue.

PubMed

Peterson, Erik; Remmenga, Marta; Hagerman, Amy D; Akkina, Judy E

2017-01-01

The United States Department of Agriculture (USDA) Animal and Plant Health Inspection Service (APHIS) conducts weekly surveillance of slaughter condemnation rates to provide early warning for emerging diseases and to monitor health trends in swine. Swine deaths in-transit are an animal welfare concern and represent lost revenue for the swine industry. This retrospective observational study used ambient temperature and humidity data from weather stations near United States slaughter plants collected from 2010 to 2015 to predict the incidence and risk of death among swine in-transit and just prior to slaughter. The risk of death for market swine at a heat index (HI), which combines the effects of temperature and humidity, indicating moderately hot weather conditions between 85 and 92°F was 1.37 times greater than that of the baseline temperature range of 54-79°F. The risk of death for cull sows at an HI between 85 and 92°F was 1.93 times greater than that of average temperatures ranging from 54 to 79°F. Roaster swine (weigh < 220 lbs and often used for whole carcass roasting), however, had 0.80 times the risk when the HI was 85-92°F compared to a baseline temperature of 54-79°F. The risk of death for roaster swine at a minimum temperature between 40 and 50°F was 1.21 times greater than that of average temperatures ranging from 54 to 79°F. The risk of death for market swine at a minimum temperature range of 40-50°F was 0.97 times that of average temperatures ranging from 54 to 79°F. And for cull sows, the risk of death at a minimum temperature range of 40-50°F was 0.81 times the risk at the average temperature ranging from 54 to 79°F. Across the study period, cumulative foregone revenue, or revenue not realized due to swine condemnations, for all swine was $18.6 million and $4.3 million for cold temperatures and high HI ranges above the baseline, respectively. Marginal foregone revenue per hog in hotter months is higher due to seasonal peaks in swine prices. As a result of this study, the USDA-APHIS swine condemnation surveillance can incorporate weekly estimated HI values and ambient temperature data for slaughter establishments to provide additional information for analysts investigating signals (noteworthy increases above baseline) for "dead" condemnations. This study suggests that current mitigation measures are often not sufficient to prevent swine deaths due to ambient temperature extremes.

Two-Phase Acto-Cytosolic Fluid Flow in a Moving Keratocyte: A 2D Continuum Model.

PubMed

Nikmaneshi, M R; Firoozabadi, B; Saidi, M S

2015-09-01

The F-actin network and cytosol in the lamellipodia of crawling cells flow in a centripetal pattern and spout-like form, respectively. We have numerically studied this two-phase flow in the realistic geometry of a moving keratocyte. Cytosol has been treated as a low viscosity Newtonian fluid flowing through the high viscosity porous medium of F-actin network. Other involved phenomena including myosin activity, adhesion friction, and interphase interaction are also discussed to provide an overall view of this problem. Adopting a two-phase coupled model by myosin concentration, we have found new accurate perspectives of acto-cytosolic flow and pressure fields, myosin distribution, as well as the distribution of effective forces across the lamellipodia of a keratocyte with stationary shape. The order of magnitude method is also used to determine the contribution of forces in the internal dynamics of lamellipodia.

Autoshaping in the rat: conditioned licking response to a stimulus that signals sucrose reinforcement.

PubMed

Reilly, Steve; Grutzmacher, Richard P.

2002-07-31

The present experiments were designed to determine if repeated presentations of an empty sipper tube (the conditioned stimulus or CS) with the response-independent delivery of a sucrose solution (the unconditioned stimulus or US) from a second spout results in the development of Pavlovian conditioned responding. In Experiment 1, rats in the experimental condition received paired CS-US presentations whereas subjects in the control condition were exposed to random presentations of CS and US. In Experiment 2, an additional control condition (CS alone) was included and, to encourage generalized responding between the US and CS, the CS tube was filled with water for all groups. The results of both experiments indicate that the CS-directed responding in the paired CS-US condition was Pavlovian in nature. Thus, the present procedure serves as an autoshaping task in which conditioned licking is generated.

Hydrogeology and groundwater availability in Clarke County, Virginia

USGS Publications Warehouse

Nelms, David L.; Moberg, Roger M.

2010-01-01

The prolonged drought between 1999 and 2002 drew attention in Clarke County, Virginia, to the quantity and sustainability of its groundwater resources. The groundwater flow systems of the county are complex and are controlled by the extremely folded and faulted geology that underlies the county. A study was conducted between October 2002 and October 2008 by the U.S. Geological Survey, in cooperation with Clarke County, Virginia, to describe the hydrogeology and groundwater availability in the county and to establish a long-term water monitoring network. The study area encompasses approximately 177 square miles and includes the carbonate and siliciclastic rocks of the Great Valley section of the Valley and Ridge Physiographic Province and the metamorphic rocks of the Blue Ridge Physiographic Province (Blue Ridge). High-yielding wells generally tend to cluster along faults, within lineament zones, and in areas of tight folding throughout the county. Water-bearing zones are generally within 250 feet (ft) of land surface; however, median depths are slightly deeper for the hydrogeologic units of the Blue Ridge than for those of the Great Valley section of the county. Total water-level fluctuations between October 2002 and October 2008 ranged from 2.86 to 87.84 ft across the study area, with an average of 24.15 ft. Generally, water-level fluctuations were greatest near hydrologic divides, in isolated elevated areas, and in the Opequon Creek Basin. Seasonally, water-level highs occur in the early spring at the end of the major groundwater recharge period and lows occur in late autumn when evapotranspiration rates begin to decrease. An overall downward trend in water levels between 2003 and 2008, which closely follows a downward trend in annual precipitation over the same period, was observed in a majority of wells in the Great Valley and in some of the wells in the Blue Ridge. Water-level fluctuations in the Blue Ridge tend to follow current meteorological conditions, and seasonal highs and lows tend to shift in response to the current conditions. Springs generally are present along faults and fold axes, and discharges for the study period ranged from dry to 10 cubic feet per second. A similar downward trend in discharges correlates with the trend in water levels and is indicative of an aquifer system that, over time, drains to a base level controlled by springs and streams. Point discharge from springs can occur as the start of flows of streams and creeks, along banks, and as discrete discharge through streambeds in the Great Valley. For the most part, streams, creeks, and rivers in the Great Valley function as aqueducts. Springs in the Blue Ridge have relatively low discharge rates, have small drainage areas, and are susceptible to current meteorological conditions. Estimates of effective groundwater recharge from 2001 to 2007 ranged from 6.4 to 23.0 inches per year (in/yr) in the Dry Marsh Run and Spout Run Basins with averages of 11.6 and 11.9 in/yr, respectively. Base flow accounted for between 80 and 97 percent of mean streamflow and averaged about 90 percent in these basins. The high base-flow index values (percent of streamflow from base flow) in the Dry Marsh Run and Spout Run Basins indicate that groundwater is the dominant source of streamflow during both wet and drought conditions. Between 46 and 82 percent of the precipitation that fell on the Dry Marsh Run and Spout Run Basins from 2001 to 2007 was removed by evapotranspiration, and an average of approximately 30 percent of the precipitation reached the water table as effective recharge. The high permeability of the rocks and low relief in these basins are not conducive for runoff; therefore, on average, only about 3 to 4 percent of the precipitation becomes runoff. Groundwater flow systems in the county are extremely vulnerable to current climatic conditions. Successive years of below-average effective recharge cause declines in water levels, spring discha

West Java Snack Mapping based on Snack Types, Main Ingredients, and Processing Techniques

NASA Astrophysics Data System (ADS)

Nurani, A. S.; Subekti, S.; Ana

2016-04-01

The research was motivated by lack of literature on archipelago snack especially from West Java. It aims to explore the snack types, the processing techniques, and the main ingredients by planning a learning material on archipelago cake especially from West Java. The research methods used are descriptive observations and interviews. The samples were randomly chosen from all regions in West Java. The findings show the identification of traditional snack from West java including: 1. snack types which are similar in all regions as research sample namely: opak, rangginang, nagasari, aliagrem, cuhcur, keripik, semprong, wajit, dodol, kecimpring, combro, tape ketan, and surabi. The typical snack types involve burayot (Garut), simping kaum (Purwakarta), surabi hejo (Karawang), papais cisaat (Subang), Papais moyong, opak bakar (Kuningan), opak oded, ranggesing (Sumedang), gapit, tapel (Cirebon), gulampo, kue aci (Tasikmalaya), wajit cililin, gurilem (West Bandung), and borondong (Bandung District); 2. various processing techniques namely: steaming, boiling, frying, caramelizing, baking, grilling, roaster, sugaring; 3. various main ingredients namely rice, local glutinous rice, rice flour, glutinous rice flour, starch, wheat flour, hunkue flour, cassava, sweet potato, banana, nuts, and corn; 4. snack classification in West Java namely (1) traditional snack, (2) creation-snack, (3) modification-snack, (4) outside influence-snack.

Breeding Increases the Efficacy of Chondrostereum purpureum in the Sprout Control of Birch

PubMed Central

Hamberg, Leena; Vartiamäki, Henna; Hantula, Jarkko

2015-01-01

We tested whether the pairing of selected isolates could be used to increase the efficiency of a decay fungus Chondrostereum purpureum (Pers. Ex Fr.) Pouzar to control hardwood sprouting in Finland. We paired C. purpureum strains efficient in sprout control or highly active in laccase production, and tested the efficacy of their progeny in spout control experiments. This procedure resulted in a strain with an efficacy superior to that of the parental strains. The mortality of birch (Betula pendula Roth. and B. pubescens Ehrh.) 1 cm in stump diameter was 78%, 56% and 9% for the best progeny, the best parental strain and the control, respectively. Mortality was only slightly higher for B. pendula than for B. pubescens but no significant differences were found between the number or maximum height of stump sprouts. Our results showed that cross breeding of this decay fungus is a good alternative in attempts to produce efficient biocontrol agents against hardwood sprouting. PMID:25674794

Reward-Based Learning Drives Rapid Sensory Signals in Medial Prefrontal Cortex and Dorsal Hippocampus Necessary for Goal-Directed Behavior.

PubMed

Le Merre, Pierre; Esmaeili, Vahid; Charrière, Eloïse; Galan, Katia; Salin, Paul-A; Petersen, Carl C H; Crochet, Sylvain

2018-01-03

The neural circuits underlying learning and execution of goal-directed behaviors remain to be determined. Here, through electrophysiological recordings, we investigated fast sensory processing across multiple cortical areas as mice learned to lick a reward spout in response to a brief deflection of a single whisker. Sensory-evoked signals were absent from medial prefrontal cortex and dorsal hippocampus in naive mice, but developed with task learning and correlated with behavioral performance in mice trained in the detection task. The sensory responses in medial prefrontal cortex and dorsal hippocampus occurred with short latencies of less than 50 ms after whisker deflection. Pharmacological and optogenetic inactivation of medial prefrontal cortex or dorsal hippocampus impaired behavioral performance. Neuronal activity in medial prefrontal cortex and dorsal hippocampus thus appears to contribute directly to task performance, perhaps providing top-down control of learned, context-dependent transformation of sensory input into goal-directed motor output. Copyright © 2017 The Author(s). Published by Elsevier Inc. All rights reserved.

A technique for fast and accurate measurement of hand volumes using Archimedes' principle.

PubMed

Hughes, S; Lau, J

2008-03-01

A new technique for measuring hand volumes using Archimedes principle is described. The technique involves the immersion of a hand in a water container placed on an electronic balance. The volume is given by the change in weight divided by the density of water. This technique was compared with the more conventional technique of immersing an object in a container with an overflow spout and collecting and weighing the volume of overflow water. The hand volume of two subjects was measured. Hand volumes were 494 +/- 6 ml and 312 +/- 7 ml for the immersion method and 476 +/- 14 ml and 302 +/- 8 ml for the overflow method for the two subjects respectively. Using plastic test objects, the mean difference between the actual and measured volume was -0.3% and 2.0% for the immersion and overflow techniques respectively. This study shows that hand volumes can be obtained more quickly than the overflow method. The technique could find an application in clinics where frequent hand volumes are required.

Microgravity nucleation and particle coagulation experiments support

NASA Technical Reports Server (NTRS)

Lilleleht, L. U.; Ferguson, F. T.; Stephens, J. R.

1992-01-01

Modifications to the nucleation apparatus suggested by our first microgravity flight campaign are complete. These included a complete 'repackaging' of the equipment into three racks along with an improved vapor spout shutter mechanism and additional thermocouples for gas temperature measurements. The 'repackaged' apparatus was used in two KC-135 campaigns: one during the week of June 3, 1991 consisting of two flights with Mg and two with Zn, and another series consisting of three flights with Zn during the week of September 23, 1991. Our effort then was focused on the analysis of these data, including further development of the mathematical models to generate the values of temperature and supersaturation at the observed points of nucleation. The efforts to apply Hale's Scaled Nucleation Theory to our experimental data have met with only limited success, most likely due to still inadequate temperature field determination. Work on the development of a preliminary particle collector system designed to capture particles from the region of nucleation and condensation, as well as from other parts of the chamber, are discussed.

Breeding increases the efficacy of Chondrostereum purpureum in the sprout control of birch.

PubMed

Hamberg, Leena; Vartiamäki, Henna; Hantula, Jarkko

2015-01-01

We tested whether the pairing of selected isolates could be used to increase the efficiency of a decay fungus Chondrostereum purpureum (Pers. Ex Fr.) Pouzar to control hardwood sprouting in Finland. We paired C. purpureum strains efficient in sprout control or highly active in laccase production, and tested the efficacy of their progeny in spout control experiments. This procedure resulted in a strain with an efficacy superior to that of the parental strains. The mortality of birch (Betula pendula Roth. and B. pubescens Ehrh.) 1 cm in stump diameter was 78%, 56% and 9% for the best progeny, the best parental strain and the control, respectively. Mortality was only slightly higher for B. pendula than for B. pubescens but no significant differences were found between the number or maximum height of stump sprouts. Our results showed that cross breeding of this decay fungus is a good alternative in attempts to produce efficient biocontrol agents against hardwood sprouting.

Multi-trophic level response to extreme metal contamination from gold mining in a subarctic lake.

PubMed

Thienpont, Joshua R; Korosi, Jennifer B; Hargan, Kathryn E; Williams, Trisha; Eickmeyer, David C; Kimpe, Linda E; Palmer, Michael J; Smol, John P; Blais, Jules M

2016-08-17

Giant Mine, located in the city of Yellowknife (Northwest Territories, Canada), is a dramatic example of subarctic legacy contamination from mining activities, with remediation costs projected to exceed $1 billion. Operational between 1948 and 2004, gold extraction at Giant Mine released large quantities of arsenic and metals from the roasting of arsenopyrite ore. We examined the long-term ecological effects of roaster emissions on Pocket Lake, a small lake at the edge of the Giant Mine lease boundary, using a spectrum of palaeoenvironmental approaches. A dated sedimentary profile tracked striking increases (approx. 1700%) in arsenic concentrations coeval with the initiation of Giant Mine operations. Large increases in mercury, antimony and lead also occurred. Synchronous changes in biological indicator assemblages from multiple aquatic trophic levels, in both benthic and pelagic habitats, indicate dramatic ecological responses to extreme metal(loid) contamination. At the peak of contamination, all Cladocera, a keystone group of primary consumers, as well as all planktonic diatoms, were functionally lost from the sediment record. No biological recovery has been inferred, despite the fact that the bulk of metal(loid) emissions occurred more than 50 years ago, and the cessation of all ore-roasting activities in Yellowknife in 1999. © 2016 The Author(s).

Determination of acrylamide during roasting of coffee.

PubMed

Bagdonaite, Kristina; Derler, Karin; Murkovic, Michael

2008-08-13

In this study different Arabica and Robusta coffee beans from different regions of the world were analyzed for acrylamide after roasting in a laboratory roaster. Due to the complex matrix and the comparably low selectivity of the LC-MS at m/ z 72, acrylamide was analyzed after derivatization with 2-mercaptobenzoic acid at m/ z 226. Additionally, the potential precursors of acrylamide (3-aminopropionamide, carbohydrates, and amino acids) were studied. The highest amounts of acrylamide formed in coffee were found during the first minutes of the roasting process [3800 ng/g in Robusta ( Coffea canephora robusta) and 500 ng/g in Arabica ( Coffea arabica)]. When the roasting time was increased, the concentration of acrylamide decreased. It was shown that especially the roasting time and temperature, species of coffee, and amount of precursors in raw material had an influence on acrylamide formation. Robusta coffee contained significantly larger amounts of acrylamide (mean = 708 ng/g) than Arabica coffee (mean = 374 ng/g). Asparagine is the limiting factor for acrylamide formation in coffee. 3-Aminopropionamide formation was observed in a dry model system with mixtures of asparagine with sugars (sucrose, glucose). Thermal decarboxylation and elimination of the alpha-amino group of asparagine at high temperatures (>220 degrees C) led to a measurable but low formation of acrylamide.

Static Hot Air and Infrared Rays Roasting are Efficient Methods for Aflatoxin Decontamination on Hazelnuts

PubMed Central

Siciliano, Ilenia; Dal Bello, Barbara; Zeppa, Giuseppe; Spadaro, Davide; Gullino, Maria Lodovica

2017-01-01

Aflatoxins are a group of secondary metabolites produced by members of Aspergillus Section Flavi that are dangerous to humans and animals. Nuts can be potentially contaminated with aflatoxins, often over the legal threshold. Food processes, including roasting, may have different effects on mycotoxins, and high temperatures have proven to be very effective in the reduction of mycotoxins. In this work, two different roasting methods—traditional static hot air roasting and infra-red rays roasting—were applied and compared for the detoxification of hazelnuts from Italy and Turkey. At the temperature of 140 °C for 40 min of exposure, detoxification was effective for both roasting techniques. Residual aflatoxins after infra-red rays treatments were lower compared to static hot air roasting. On Italian hazelnuts, residual aflatoxins were lower than 5%, while for Turkish hazelnuts they were lower than 15% after 40 min of exposure to an infra-red rays roaster. After roasting, the perisperm was detached from the nuts and analyzed for aflatoxin contents. Residual aflatoxins in the perisperm ranged from 80% up to 100%. After roasting, the lipid profile and the nutritional quality of hazelnuts were not affected. Fatty acid methyl esters analyses showed a similar composition for Italian and Turkish hazelnuts. PMID:28230792

Multi-trophic level response to extreme metal contamination from gold mining in a subarctic lake

PubMed Central

Korosi, Jennifer B.; Hargan, Kathryn E.; Williams, Trisha; Eickmeyer, David C.; Kimpe, Linda E.; Palmer, Michael J.; Smol, John P.; Blais, Jules M.

2016-01-01

Giant Mine, located in the city of Yellowknife (Northwest Territories, Canada), is a dramatic example of subarctic legacy contamination from mining activities, with remediation costs projected to exceed $1 billion. Operational between 1948 and 2004, gold extraction at Giant Mine released large quantities of arsenic and metals from the roasting of arsenopyrite ore. We examined the long-term ecological effects of roaster emissions on Pocket Lake, a small lake at the edge of the Giant Mine lease boundary, using a spectrum of palaeoenvironmental approaches. A dated sedimentary profile tracked striking increases (approx. 1700%) in arsenic concentrations coeval with the initiation of Giant Mine operations. Large increases in mercury, antimony and lead also occurred. Synchronous changes in biological indicator assemblages from multiple aquatic trophic levels, in both benthic and pelagic habitats, indicate dramatic ecological responses to extreme metal(loid) contamination. At the peak of contamination, all Cladocera, a keystone group of primary consumers, as well as all planktonic diatoms, were functionally lost from the sediment record. No biological recovery has been inferred, despite the fact that the bulk of metal(loid) emissions occurred more than 50 years ago, and the cessation of all ore-roasting activities in Yellowknife in 1999. PMID:27534958

Characterization of the polymerization of furfuryl alcohol during roasting of coffee.

PubMed

Swasti, Yuliana Reni; Murkovic, Michael

2012-09-01

The polymerization of furfuryl alcohol contributes to the formation of the brown colour in heated foods, in addition to the Maillard and caramelization reactions. During the heating of food, furfuryl alcohol is formed via the degradation of quinic acid or 1,2-enediols. Furfuryl alcohol is a mutagenic compound. In acidic conditions it is able to polymerize and form aliphatic polymers that show a brown colour. Herein we show that furfuryl alcohol polymerizes in a model system by incubating it in 1 M HCl at room temperature. Some of the reaction products are dimers, trimers, tetramers, and pentamers with methylene linkages. The degree of polymerization and the amount of those furfuryl alcohol oligomers increased with increasing reaction time. The results of this model system were used to characterize the polymerization of furfuryl alcohol which is produced during roasting of coffee. The coffee was roasted at 210 °C for 2, 3, 4, 5, and 6 min with a home coffee roaster. Furfuryl alcohol and its dimer were found in roasted coffee after 2 and 3 min of roasting respectively, reaching a maximum amount after 4 min. Perhaps due to further reactions, the dimeric furfuryl alcohol concentration starts to decrease after 4 min. We propose that the polymers of furfuryl alcohol contribute to the brown colour of roasted foods.

Static Hot Air and Infrared Rays Roasting are Efficient Methods for Aflatoxin Decontamination on Hazelnuts.

PubMed

Siciliano, Ilenia; Dal Bello, Barbara; Zeppa, Giuseppe; Spadaro, Davide; Gullino, Maria Lodovica

2017-02-21

Aflatoxins are a group of secondary metabolites produced by members of Aspergillus Section Flavi that are dangerous to humans and animals. Nuts can be potentially contaminated with aflatoxins, often over the legal threshold. Food processes, including roasting, may have different effects on mycotoxins, and high temperatures have proven to be very effective in the reduction of mycotoxins. In this work, two different roasting methods-traditional static hot air roasting and infra-red rays roasting-were applied and compared for the detoxification of hazelnuts from Italy and Turkey. At the temperature of 140 °C for 40 min of exposure, detoxification was effective for both roasting techniques. Residual aflatoxins after infra-red rays treatments were lower compared to static hot air roasting. On Italian hazelnuts, residual aflatoxins were lower than 5%, while for Turkish hazelnuts they were lower than 15% after 40 min of exposure to an infra-red rays roaster. After roasting, the perisperm was detached from the nuts and analyzed for aflatoxin contents. Residual aflatoxins in the perisperm ranged from 80% up to 100%. After roasting, the lipid profile and the nutritional quality of hazelnuts were not affected. Fatty acid methyl esters analyses showed a similar composition for Italian and Turkish hazelnuts.

Using multiple bed load measurements: Toward the identification of bed dilation and contraction in gravel-bed rivers

NASA Astrophysics Data System (ADS)

Marquis, G. A.; Roy, A. G.

2012-02-01

This study examines bed load transport processes in a small gravel-bed river (Béard Creek, Québec) using three complementary methods: bed elevation changes between successive floods, bed activity surveys using tags inserted into the bed, and bed load transport rates from bed load traps. The analysis of 20 flood events capable of mobilizing bed material led to the identification of divergent results among the methods. In particular, bed elevation changes were not consistent with the bed activity surveys. In many cases, bed elevation changes were significant (1 to 2 times the D50) even if the bed surface had not been activated during the flood, leading to the identification of processes of bed dilation and contraction that occurred over 10% to 40% of the bed surface. These dynamics of the river bed prevent accurate derivation of bed load transport rates from topographic changes, especially for low magnitude floods. This paper discusses the mechanisms that could explain the dilation and contraction of particles within the bed and their implications in fluvial dynamics. Bed contraction seems to be the result of the winnowing of the fine sediments under very low gravel transport. Bed dilation seems to occur on patches of the bed at the threshold of motion where various processes such as fine sediment infiltration lead to the maintenance of a larger sediment framework volume. Both processes are also influenced by flood history and the initial local bed state and in turn may have a significant impact on sediment transport and morphological changes in gravel-bed rivers.

Ability of bed bug-detecting canines to locate live bed bugs and viable bed bug eggs.

PubMed

Pfiester, Margie; Koehler, Philip G; Pereira, Roberto M

2008-08-01

The bed bug, Cimex lectularius L., like other bed bug species, is difficult to visually locate because it is cryptic. Detector dogs are useful for locating bed bugs because they use olfaction rather than vision. Dogs were trained to detect the bed bug (as few as one adult male or female) and viable bed bug eggs (five, collected 5-6 d after feeding) by using a modified food and verbal reward system. Their efficacy was tested with bed bugs and viable bed bug eggs placed in vented polyvinyl chloride containers. Dogs were able to discriminate bed bugs from Camponotus floridanus Buckley, Blattella germanica (L.), and Reticulitermes flavipes (Kollar), with a 97.5% positive indication rate (correct indication of bed bugs when present) and 0% false positives (incorrect indication of bed bugs when not present). Dogs also were able to discriminate live bed bugs and viable bed bug eggs from dead bed bugs, cast skins, and feces, with a 95% positive indication rate and a 3% false positive rate on bed bug feces. In a controlled experiment in hotel rooms, dogs were 98% accurate in locating live bed bugs. A pseudoscent prepared from pentane extraction of bed bugs was recognized by trained dogs as bed bug scent (100% indication). The pseudoscent could be used to facilitate detector dog training and quality assurance programs. If trained properly, dogs can be used effectively to locate live bed bugs and viable bed bug eggs.

Acoustic bed velocity and bed load dynamics in a large sand bed river

USGS Publications Warehouse

Gaeuman, D.; Jacobson, R.B.

2006-01-01

Development of a practical technology for rapid quantification of bed load transport in large rivers would represent a revolutionary advance for sediment monitoring and the investigation of fluvial dynamics. Measurement of bed load motion with acoustic Doppler current profiles (ADCPs) has emerged as a promising approach for evaluating bed load transport. However, a better understanding of how ADCP data relate to conditions near the stream bed is necessary to make the method practical for quantitative applications. In this paper, we discuss the response of ADCP bed velocity measurements, defined as the near-bed sediment velocity detected by the instrument's bottom-tracking feature, to changing sediment-transporting conditions in the lower Missouri River. Bed velocity represents a weighted average of backscatter from moving bed load particles and spectral reflections from the immobile bed. The ratio of bed velocity to mean bed load particle velocity depends on the concentration of the particles moving in the bed load layer, the bed load layer thickness, and the backscatter strength from a unit area of moving particles relative to the echo strength from a unit area of unobstructed bed. A model based on existing bed load transport theory predicted measured bed velocities from hydraulic and grain size measurements with reasonable success. Bed velocities become more variable and increase more rapidly with shear stress when the transport stage, defined as the ratio of skin friction to the critical shear stress for particle entrainment, exceeds a threshold of about 17. This transition in bed velocity response appears to be associated with the appearance of longer, flatter bed forms at high transport stages.

The Cm56 tRNA modification in archaea is catalyzed either by a specific 2'-O-methylase, or a C/D sRNP.

PubMed

Renalier, Marie-Hélène; Joseph, Nicole; Gaspin, Christine; Thebault, Patricia; Mougin, Annie

2005-07-01

We identified the first archaeal tRNA ribose 2'-O-methylase, aTrm56, belonging to the Cluster of Orthologous Groups (COG) 1303 that contains archaeal genes only. The corresponding protein exhibits a SPOUT S-adenosylmethionine (AdoMet)-dependent methyltransferase domain found in bacterial and yeast G18 tRNA 2'-O-methylases (SpoU, Trm3). We cloned the Pyrococcus abyssi PAB1040 gene belonging to this COG, expressed and purified the corresponding protein, and showed that in vitro, it specifically catalyzes the AdoMet-dependent 2'-O-ribose methylation of C at position 56 in tRNA transcripts. This tRNA methylation is present only in archaea, and the gene for this enzyme is present in all the archaeal genomes sequenced up to now, except in the crenarchaeon Pyrobaculum aerophilum. In this archaea, the C56 2'-O-methylation is provided by a C/D sRNP. Our work is the first demonstration that, within the same kingdom, two different mechanisms are used to modify the same nucleoside in tRNAs.

An Outbreak of Vibrio cholerae O1 infections on Ebeye Island, Republic of the Marshall Islands, associated with use of an adequately chlorinated water source.

PubMed

Beatty, Mark E; Jack, Tom; Sivapalasingam, Sumathi; Yao, Sandra S; Paul, Irene; Bibb, Bill; Greene, Kathy D; Kubota, Kristy; Mintz, Eric D; Brooks, John T

2004-01-01

In December 2000, physicians in the Republic of the Marshall Islands reported the first known outbreak of Vibrio cholerae O1 infection (biotype El Tor, serotype Ogawa) from this country. In a matched case-control study on Ebeye Island, patients with cholera (n=53) had greater odds than persons without cholera (n=104) to have drunk adequately chlorinated water collected from a US military installation on neighboring Kwajalein Island and transported back to Ebeye (matched odds ratio [MOR], 8.0; P=.01). Transporting or storing drinking water in a water cooler with a spout and a tight-fitting lid was associated with reduced odds of illness (MOR, 0.24; P<.01), as was drinking bottled water (MOR, 0.08; P<.01), boiled water (MOR, 0.47; P=.02), or water flavored with powdered drink mixes (MOR, 0.18; P<.01). No cases of cholera were reported among Kwajalein residents. This outbreak highlights the critical importance of handling and storing drinking water safely, especially during outbreaks of gastrointestinal illness.

Drying of restructured chips made from the old stalks of Asparagus officinalis: impact of different drying methods.

PubMed

Liu, Zhenbin; Zhang, Min; Wang, Yuchuan

2016-06-01

Old stalks of Asparagus officinalis, which account for one third of the total length of each spear, are always discarded as waste. To make full use of the resource, a kind of restructured Asparagus officinalis chip was made. The effects of pulse-spouted microwave-assisted vacuum drying (PSMVD), microwave-assisted vacuum drying (MVD) and vacuum drying (VD) on texture, color and other quality parameters of restructured chips were then studied to obtain high-quality dried chips. Results indicated that the drying time was significantly affected by drying methods, and PSMVD had much better drying uniformity than MVD. The expansion ratio and crispness of chips increased with increasing microwave power and vacuum degree. The browning reaction of samples in VD was more serious, which was confirmed by the results of color test and electronic nose. The PSMVD drying method showed much better drying uniformity than MVD. The dried chips obtained by PSMVD showed optimal quality and were more readily accepted by consumers. © 2015 Society of Chemical Industry. © 2015 Society of Chemical Industry.

Structural Chemistry of Human RNA Methyltransferases.

PubMed

Schapira, Matthieu

2016-03-18

RNA methyltransferases (RNMTs) play important roles in RNA stability, splicing, and epigenetic mechanisms. They constitute a promising target class that is underexplored by the medicinal chemistry community. Information of relevance to drug design can be extracted from the rich structural coverage of human RNMTs. In this work, the structural chemistry of this protein family is analyzed in depth. Unlike most methyltransferases, RNMTs generally feature a substrate-binding site that is largely open on the cofactor-binding pocket, favoring the design of bisubstrate inhibitors. Substrate purine or pyrimidines are often sandwiched between hydrophobic walls that can accommodate planar ring systems. When the substrate base is laying on a shallow surface, a 5' flanking base is sometimes anchored in a druggable cavity. The cofactor-binding site is structurally more diverse than in protein methyltransferases and more druggable in SPOUT than in Rossman-fold enzymes. Finally, conformational plasticity observed both at the substrate and cofactor binding sites may be a challenge for structure-based drug design. The landscape drawn here may inform ongoing efforts toward the discovery of the first human RNMT inhibitors.

Endotoxin, coliform, and dust levels in various types of rodent bedding.

PubMed

Whiteside, Tanya E; Thigpen, Julius E; Kissling, Grace E; Grant, Mary G; Forsythe, Diane

2010-03-01

Endotoxins in grain dust, household dust, and animal bedding may induce respiratory symptoms in rodents and humans. We assayed the endotoxin, coliform, and dust levels in 20 types of rodent bedding. Endotoxin concentrations were measured by using a commercial test kit, coliform counts were determined by using conventional microbiologic procedures, and dust content was evaluated by using a rotating-tapping shaker. Paper bedding types contained significantly less endotoxin than did other bedding types; the highest levels of endotoxin were detected in hardwood and corncob beddings. The range of endotoxin content for each bedding type was: corncob bedding, 1913 to 4504 endotoxin units per gram (EU/g); hardwood bedding, 3121 to 5401 EU/g; corncob-paper mixed bedding, 1586 to 2416 EU/g; and paper bedding, less than 5 to 105 EU/g. Coliform counts varied from less than 10 to 7591 cfu/g in corncob beddings, 90 to 4010 cfu/g in corncob-paper mixed beddings, less than 10 to 137 cfu/g in hardwood beddings, and less than 10 cfu/g in paper beddings. Average dust content was less than 0.15% in all commercial bedding types. We conclude that paper bedding is the optimal bedding type for conducting LPS inhalation studies and that rodent bedding containing high levels of endotoxin may alter the results of respiratory and immunologic studies in rodents.

Endotoxin, Coliform, and Dust Levels in Various Types of Rodent Bedding

PubMed Central

Whiteside, Tanya E; Thigpen, Julius E; Kissling, Grace E; Grant, Mary G; Forsythe, Diane B

2010-01-01

Endotoxins in grain dust, household dust, and animal bedding may induce respiratory symptoms in rodents and humans. We assayed the endotoxin, coliform, and dust levels in 20 types of rodent bedding. Endotoxin concentrations were measured by using a commercial test kit, coliform counts were determined by using conventional microbiologic procedures, and dust content was evaluated by using a rotating–tapping shaker. Paper bedding types contained significantly less endotoxin than did other bedding types; the highest levels of endotoxin were detected in hardwood and corncob beddings. The range of endotoxin content for each bedding type was: corncob bedding, 1913 to 4504 endotoxin units per gram (EU/g); hardwood bedding, 3121 to 5401 EU/g; corncob–paper mixed bedding, 1586 to 2416 EU/g; and paper bedding, less than 5 to 105 EU/g. Coliform counts varied from less than 10 to 7591 cfu/g in corncob beddings, 90 to 4010 cfu/g in corncob–paper mixed beddings, less than 10 to 137 cfu/g in hardwood beddings, and less than 10 cfu/g in paper beddings. Average dust content was less than 0.15% in all commercial bedding types. We conclude that paper bedding is the optimal bedding type for conducting LPS inhalation studies and that rodent bedding containing high levels of endotoxin may alter the results of respiratory and immunologic studies in rodents. PMID:20353693

Field assessment of alternative bed-load transport estimators

USGS Publications Warehouse

Gaeuman, G.; Jacobson, R.B.

2007-01-01

Measurement of near-bed sediment velocities with acoustic Doppler current profilers (ADCPs) is an emerging approach for quantifying bed-load sediment fluxes in rivers. Previous investigations of the technique have relied on conventional physical bed-load sampling to provide reference transport information with which to validate the ADCP measurements. However, physical samples are subject to substantial errors, especially under field conditions in which surrogate methods are most needed. Comparisons between ADCP bed velocity measurements with bed-load transport rates estimated from bed-form migration rates in the lower Missouri River show a strong correlation between the two surrogate measures over a wide range of mild to moderately intense sediment transporting conditions. The correlation between the ADCP measurements and physical bed-load samples is comparatively poor, suggesting that physical bed-load sampling is ineffective for ground-truthing alternative techniques in large sand-bed rivers. Bed velocities measured in this study became more variable with increasing bed-form wavelength at higher shear stresses. Under these conditions, bed-form dimensions greatly exceed the region of the bed ensonified by the ADCP, and the magnitude of the acoustic measurements depends on instrument location with respect to bed-form crests and troughs. Alternative algorithms for estimating bed-load transport from paired longitudinal profiles of bed topography were evaluated. An algorithm based on the routing of local erosion and deposition volumes that eliminates the need to identify individual bed forms was found to give results similar to those of more conventional dune-tracking methods. This method is particularly useful in cases where complex bed-form morphology makes delineation of individual bed forms difficult. ?? 2007 ASCE.

The optimal design of the bed structure of bedstand based on ABAQUS

NASA Astrophysics Data System (ADS)

Yang, Xudong; Dong, Yu; Ge, Qingkuan; Wang, Song

2017-12-01

Hydraulic transmission bedstand is one kind of the most commonly used in engineering machinery companies, and the bed structure is the most important part. Based on the original hydraulic transmission bedstand bed structure and the CAE technology, the original bed structure is improved. The optimized bed greatly saves the material of the production bed and improves the seismic performance of the bed. In the end, the performance of the optimized bed was compared with the original bed.

Particle size variations between bed load and bed material in natural gravel bed channels

Treesearch

Thomas E. Lisle

1995-01-01

Abstract - Particle sizes of bed load and bed material that represent materials transported and stored over a period of years are used to investigate selective transport in 13 previously sampled, natural gravel bed channels. The ratio (D*) of median particle size of bed material to the transport- and frequency-weighted mean of median bed load size decreases to unity...

Marginal bed load transport in a gravel bed stream, Sagehen Creek, California

USGS Publications Warehouse

Andrews, E.D.

1994-01-01

Marginal bed load transport describes the condition when relatively few bed particles are moving at any time. Bed particles resting in the shallowest bed pockets will move when the dimensionless shear stress т* exceeds a value of about 0.020. As т* increases, the number of bed particles moving increases. Significant motion of bed particles, i.e., when a substantial fraction of the bed particles are moving, occurs when т* exceeds a value of about 0.060. Thus marginal bed load transport occurs over the domain 0.020 < т* < 0.060. Marginal bed load transport rates and associated hydraulic characteristics of Sagehen Creek, a small mountain gravel bed stream, were measured on 55 days at discharges ranging from slightly less than one half of the bank-full discharge to more than 4 times the bank-full discharge. Dimensionless shear stress varied from 0.032 to 0.042, and bed particles as large as the 80th percentile of the bed surface were transported. The relation between reference dimensionless shear stress and relative particle protrusion for Sagehen Creek was determined by varying т*ri to obtain the best fit of the Parker bed load function to the measured transport rates. During the period of record (water years 1954–1991), the mean annual quantity of bed load transported past the Sagehen Creek gage was 24.7 tons. Forty-seven percent of all bed load transported during the 38 years of record occurred in just 6 years. During 10 of the 38 years of record, essentially no bed load was transported. The median diameter of bed load was 26 mm, compared to 58 mm in the surface bed material.

A Comparison of Inpatient Adult Psychiatric Services in Italy and Canada.

PubMed

Guaiana, Giuseppe; O'Reilly, Richard; Grassi, Luigi

2018-05-03

We examine the possibility the Organisation for Economic Co-operation and Development (OECD) bed count for Italy may be an underestimation of the actual beds available. We compared bedded services for mental disorders in two regions in Italy and Canada respectively. We found out that if we consider acute psychiatric beds only, the district of Ferrara has 30 beds (8.5 per 100,000) and the Middlesex and Elgin Counties have 89 beds (16.3 beds for 100,000). However, if we include the rehabilitation beds (that are located within a hospital setting in Ontario and in a residential community setting in Ferrara), we find that the district of Ferrara has 95 beds (27.0 per 100,000) and the Middlesex and Elgin Counties have 176 beds (32.3 per 100,000). As a result, the 10/100,000 beds rate for Italy reported by the OECD is an underestimate compared to figures reported for most other countries, as the beds included are hospital beds only.

Detection of patient's bed statuses in 3D using a Microsoft Kinect.

PubMed

Li, Yun; Berkowitz, Lyle; Noskin, Gary; Mehrotra, Sanjay

2014-01-01

Patients spend the vast majority of their hospital stay in an unmonitored bed where various mobility factors can impact patient safety and quality. Specifically, bed positioning and a patient's related mobility in that bed can have a profound impact on risks such as pneumonias, blood clots, bed ulcers and falls. This issue has been exacerbated as the nurse-per-bed (NPB) ratio has decreased in recent years. To help assess these risks, it is critical to monitor a hospital bed's positional status (BPS). Two bed positional statuses, bed height (BH) and bed chair angle (BCA), are of critical interests for bed monitoring. In this paper, we develop a bed positional status detection system using a single Microsoft Kinect. Experimental results show that we are able to achieve 94.5% and 93.0% overall accuracy of the estimated BCA and BH in a simulated patient's room environment.

Utility of Recycled Bedding for Laboratory Rodents

PubMed Central

Miyamoto, Toru; Li, Zhixia; Kibushi, Tomomi; Okano, Shinya; Yamasaki, Nakamichi; Kasai, Noriyuki

2009-01-01

Animal facilities generate a large amount of used bedding containing excrement as medical waste. We developed a recycling system for used bedding that involves soft hydrothermal processing. In this study, we examined the effects of bedding type on growth, hematologic and serum biochemical values, and organ weights of female and male mice reared on either recycled or fresh bedding from 3 to 33 wk of age. Neither growth nor physiology differed between mice housed on recycled bedding compared with fresh bedding. When 14-wk-old mice were bred, litter size and total number of weaned pups showed no significant differences between animals raised on recycled or fresh bedding. Because bedding type influences the environment within cages and animal rooms, we evaluated particulate and ammonia data from cages and animal rooms. Values were significantly lower from cages and rooms that used recycled bedding than from those using fresh bedding, thus indicating that recycled bedding has the potential to improve the environment within both cages and animal rooms. Overall, this study revealed that recycled bedding is an excellent material for use in housing laboratory rodents. Specifically, recycled bedding may reduce medical waste and maintain healthy environments within cages and animal rooms. PMID:19653951

Real-time monitoring of a coffee roasting process with near infrared spectroscopy using multivariate statistical analysis: A feasibility study.

PubMed

Catelani, Tiago A; Santos, João Rodrigo; Páscoa, Ricardo N M J; Pezza, Leonardo; Pezza, Helena R; Lopes, João A

2018-03-01

This work proposes the use of near infrared (NIR) spectroscopy in diffuse reflectance mode and multivariate statistical process control (MSPC) based on principal component analysis (PCA) for real-time monitoring of the coffee roasting process. The main objective was the development of a MSPC methodology able to early detect disturbances to the roasting process resourcing to real-time acquisition of NIR spectra. A total of fifteen roasting batches were defined according to an experimental design to develop the MSPC models. This methodology was tested on a set of five batches where disturbances of different nature were imposed to simulate real faulty situations. Some of these batches were used to optimize the model while the remaining was used to test the methodology. A modelling strategy based on a time sliding window provided the best results in terms of distinguishing batches with and without disturbances, resourcing to typical MSPC charts: Hotelling's T 2 and squared predicted error statistics. A PCA model encompassing a time window of four minutes with three principal components was able to efficiently detect all disturbances assayed. NIR spectroscopy combined with the MSPC approach proved to be an adequate auxiliary tool for coffee roasters to detect faults in a conventional roasting process in real-time. Copyright © 2017 Elsevier B.V. All rights reserved.

A general power equation for predicting bed load transport rates in gravel bed rivers

Treesearch

Jeffrey J. Barry; John M. Buffington; John G. King

2004-01-01

A variety of formulae has been developed to predict bed load transport in gravel bed rivers, ranging from simple regressions to complex multiparameter formulations. The ability to test these formulae across numerous field sites has, until recently, been hampered by a paucity of bed load transport data for gravel bed rivers. We use 2104 bed load transport observations...

Method and apparatus for enhancing the desulfurization of hot coal gas in a fluid-bed coal gasifier

DOEpatents

Grindley, T.

1988-04-05

A process and apparatus for providing additional desulfurization of the hot gas produced in a fluid-bed coal gasifier, within the gasifier is described. A fluid-bed of iron oxide is located inside the gasifier above the gasification bed in a fluid-bed coal gasifier in which in-bed desulfurization by lime/limestone takes place. The product gases leave the gasification bed typically at 1600 to 1800 F and are partially quenched with water to 1000 to 1200 F before entering the iron oxide bed. The iron oxide bed provides additional desulfurization beyond that provided by the lime /limestone. 1 fig.

Method for enhancing the desulfurization of hot coal gas in a fluid-bed coal gasifier

DOEpatents

Grindley, Thomas

1989-01-01

A process and apparatus for providing additional desulfurization of the hot gas produced in a fluid-bed coal gasifier, within the gasifier. A fluid-bed of iron oxide is located inside the gasifier above the gasification bed in a fluid-bed coal gasifier in which in-bed desulfurization by lime/limestone takes place. The product gases leave the gasification bed typically at 1600.degree. to 1800.degree. F. and are partially quenched with water to 1000.degree. to 1200.degree. F. before entering the iron oxide bed. The iron oxide bed provides additional desulfurization beyond that provided by the lime/limestone.

DNA profiling of trace DNA recovered from bedding.

PubMed

Petricevic, Susan F; Bright, Jo-Anne; Cockerton, Sarah L

2006-05-25

Trace DNA is often detected on handled items and worn clothing examined in forensic laboratories. In this study, the potential transfer of trace DNA to bedding by normal contact, when an individual sleeps in a bed, is examined. Volunteers slept one night on a new, lower bed sheet in their own bed and one night in a bed foreign to them. Samples from the sheets were collected and analysed by DNA profiling. The results indicate that the DNA profile of an individual can be obtained from bedding after one night of sleeping in a bed. The DNA profile of the owner of the bed could also be detected in the foreign bed experiments. Since mixed DNA profiles can be obtained from trace DNA on bedding, caution should be exercised when drawing conclusions from DNA profiling results obtained from such samples. This transfer may have important repercussions in sexual assault investigations.

AIR PASSIVATION OF METAL HYDRIDE BEDS FOR WASTE DISPOSAL

DOE Office of Scientific and Technical Information (OSTI.GOV)

Klein, J; R. H. Hsu, R

2007-07-02

Metal hydride beds offer compact, safe storage of tritium. After metal hydride beds have reached the end of their useful life, the beds will replaced with new beds and the old beds prepared for disposal. One acceptance criteria for hydride bed waste disposal is that the material inside the bed not be pyrophoric. To determine the pyrophoric nature of spent metal hydride beds, controlled air ingress tests were performed. A simple gas handling manifold fitted with pressure transducers and a calibrated volume were used to introduce controlled quantities of air into a metal hydride bed and the bed temperature risemore » monitored for reactivity with the air. A desorbed, 4.4 kg titanium prototype hydride storage vessel (HSV) produced a 4.4 C internal temperature rise upon the first air exposure cycle and a 0.1 C temperature rise upon a second air exposure. A total of 346 scc air was consumed by the bed (0.08 scc per gram Ti). A desorbed, 9.66 kg LaNi{sub 4.25}Al{sub 0.75} prototype storage bed experienced larger temperature rises over successive cycles of air ingress and evacuation. The cycles were performed over a period of days with the bed effectively passivated after the 12th cycle. Nine to ten STP-L of air reacted with the bed producing both oxidized metal and water.« less

7 CFR 3201.15 - Bedding, bed linens, and towels.

Code of Federal Regulations, 2014 CFR

2014-01-01

... group of woven cloth products used as coverings on a bed. Bedding includes products such as blankets, bedspreads, comforters, and quilts. (2) Bed linens are woven cloth sheets and pillowcases used in bedding. (3) Towels are woven cloth products used primarily for drying and wiping. (b) Minimum biobased content. The...

7 CFR 2902.15 - Bedding, bed linens, and towels.

Code of Federal Regulations, 2011 CFR

2011-01-01

... group of woven cloth products used as coverings on a bed. Bedding includes products such as blankets, bedspreads, comforters, and quilts. (2) Bed linens are woven cloth sheets and pillowcases used in bedding. (3) Towels are woven cloth products used primarily for drying and wiping. (b) Minimum biobased content. The...

7 CFR 3201.15 - Bedding, bed linens, and towels.

Code of Federal Regulations, 2012 CFR

2012-01-01

... group of woven cloth products used as coverings on a bed. Bedding includes products such as blankets, bedspreads, comforters, and quilts. (2) Bed linens are woven cloth sheets and pillowcases used in bedding. (3) Towels are woven cloth products used primarily for drying and wiping. (b) Minimum biobased content. The...

7 CFR 3201.15 - Bedding, bed linens, and towels.

Code of Federal Regulations, 2013 CFR

2013-01-01

... group of woven cloth products used as coverings on a bed. Bedding includes products such as blankets, bedspreads, comforters, and quilts. (2) Bed linens are woven cloth sheets and pillowcases used in bedding. (3) Towels are woven cloth products used primarily for drying and wiping. (b) Minimum biobased content. The...

The underlying reasons for very high levels of bed net use, and higher malaria infection prevalence among bed net users than non-users in the Tanzanian city of Dar es Salaam: a qualitative study.

PubMed

Msellemu, Daniel; Shemdoe, Aloysia; Makungu, Christina; Mlacha, Yeromini; Kannady, Khadija; Dongus, Stefan; Killeen, Gerry F; Dillip, Angel

2017-10-23

Bed nets reduce malaria-related illness and deaths, by forming a protective barrier around people sleeping under them. When impregnated with long-lasting insecticide formulations they also repel or kill mosquitoes attempting to feed upon sleeping humans, and can even suppress entire populations of malaria vectors that feed predominantly upon humans. Nevertheless, an epidemiological study in 2012 demonstrated higher malaria prevalence among bed net users than non-users in urban Dar es Salaam, Tanzania. Focus group discussions were conducted with women from four selected wards of Dar es Salaam city, focusing on four major themes relating to bed net use behaviours: (1) reasons for bed net use, (2) reasons for not using bed nets, (3) stimuli or reminders for people to use a bed net (4) perceived reasons for catching malaria while using a bed net. An analytical method by framework grouping of relevant themes was used address key issues of relevance to the study objectives. Codes were reviewed and grouped into categories and themes. All groups said the main reason for bed net use was protection against malaria. Houses with well-screened windows, with doors that shut properly, and that use insecticidal sprays against mosquitoes, were said not to use bed nets, while frequent attacks from malaria was the main stimulus for people to use bed nets. Various reasons were mentioned as potential reasons that compromise bed net efficacy, the most common of which were: (1) bed net sharing by two or more people, especially if one occupant tends to come to bed late at night, and does not tuck in the net 71%; (2) one person shares the bed but does not use the net, moving it away from the side on which s/he sleeps 68%; (3) ineffective usage habits, called ulalavi, in which a sprawling sleeper either touches the net while sleeping up against it or leaves a limb hanging outside of it 68%. Less common reasons mentioned included: (1) Small bed nets which become un-tucked at night (31%); (2) Bed nets with holes large enough to allow mosquitoes to pass (28%); and (3) Going to bed late after already being bitten outdoors (24%). Behaviours associated with bed net use like; bed sharing, bed net non compliant-bedfellow, sleeping pattern like ulalavi and some physical bed net attributes compromise its effectiveness and supposedly increase of malaria infection to bed net users. While some well-screened houses looked to instigate low malaria prevalence to non-bed net users.

Odorous Volatile Organic Compounds, Escherichia coli, and Nutrient Concentrations when Kiln-Dried Pine Chips and Corn Stover Bedding Are Used in Beef Bedded Manure Packs.

PubMed

Spiehs, Mindy J; Berry, Elaine D; Wells, James E; Parker, David B; Brown-Brandl, Tami M

2017-07-01

Pine ( spp.) bedding has been shown to lower the concentration of odorous volatile organic compounds (VOCs) and pathogenic bacteria compared with corn ( L.) stover bedding, but availability and cost limit the use of pine bedding in cattle confinement facilities. The objectives of this study were to determine if the addition of pine wood chips to laboratory-scaled bedded packs containing corn stover (i) reduced odorous VOC emissions; (ii) reduced total ; and (iii) changed the nutrient composition of the resulting manure-bedded packs. Bedding treatments included 0, 10, 20, 30, 40, 60, 80, and 100% pine chips, with the balance being corn stover. Four bedded packs for each mixture were maintained for 42 d ( = 4 observations per bedding material). The production of total sulfur compounds increased significantly when 100% pine chips were used (44.72 ng L) compared with bedding mixture containing corn stover (18.0-24.56 ng L). The carbon-to-nitrogen ratio exceeded the ideal ratio of 24:1 for the optimum activity of soil microorganisms when ≥60% pine chips (25.3-27.5 ng L) were included in the mixture. The use of 100% pine chips as bedding increased sulfide concentration in the facility 1.8 to 2.4 times over the use of corn stover bedding. was not influenced by the addition of pine chips to the corn stover bedding material but did decrease as the bedded pack aged. Bedding material mixtures containing 30 to 60% pine and 40 to 70% corn stover may be the ideal combination to mitigate odors from livestock facilities using deep bedded systems. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Development of the 7-Item Binge-Eating Disorder Screener (BEDS-7)

PubMed Central

Deal, Linda S.; DiBenedetti, Dana B.; Nelson, Lauren; Fehnel, Sheri E.; Brown, T. Michelle

2016-01-01

Objective Develop a brief, patient-reported screening tool designed to identify individuals with probable binge-eating disorder (BED) for further evaluation or referral to specialists. Methods Items were developed on the basis of the DSM-5 diagnostic criteria, existing tools, and input from 3 clinical experts (January 2014). Items were then refined in cognitive debriefing interviews with participants self-reporting BED characteristics (March 2014) and piloted in a multisite, cross-sectional, prospective, noninterventional study consisting of a semistructured diagnostic interview (to diagnose BED) and administration of the pilot Binge-Eating Disorder Screener (BEDS), Binge Eating Scale (BES), and RAND 36-Item Short-Form Health Survey (RAND-36) (June 2014–July 2014). The sensitivity and specificity of classification algorithms (formed from the pilot BEDS item-level responses) in predicting BED diagnosis were evaluated. The final algorithm was selected to minimize false negatives and false positives, while utilizing the fewest number of BEDS items. Results Starting with the initial BEDS item pool (20 items), the 13-item pilot BEDS resulted from the cognitive debriefing interviews (n = 13). Of the 97 participants in the noninterventional study, 16 were diagnosed with BED (10/62 female, 16%; 6/35 male, 17%). Seven BEDS items (BEDS-7) yielded 100% sensitivity and 38.7% specificity. Participants correctly identified (true positives) had poorer BES scores and RAND-36 scores than participants identified as true negatives. Conclusions Implementation of the brief, patient-reported BEDS-7 in real-world clinical practice is expected to promote better understanding of BED characteristics and help physicians identify patients who may have BED. PMID:27486542

Development of the 7-Item Binge-Eating Disorder Screener (BEDS-7).

PubMed

Herman, Barry K; Deal, Linda S; DiBenedetti, Dana B; Nelson, Lauren; Fehnel, Sheri E; Brown, T Michelle

2016-01-01

Develop a brief, patient-reported screening tool designed to identify individuals with probable binge-eating disorder (BED) for further evaluation or referral to specialists. Items were developed on the basis of the DSM-5 diagnostic criteria, existing tools, and input from 3 clinical experts (January 2014). Items were then refined in cognitive debriefing interviews with participants self-reporting BED characteristics (March 2014) and piloted in a multisite, cross-sectional, prospective, noninterventional study consisting of a semistructured diagnostic interview (to diagnose BED) and administration of the pilot Binge-Eating Disorder Screener (BEDS), Binge Eating Scale (BES), and RAND 36-Item Short-Form Health Survey (RAND-36) (June 2014-July 2014). The sensitivity and specificity of classification algorithms (formed from the pilot BEDS item-level responses) in predicting BED diagnosis were evaluated. The final algorithm was selected to minimize false negatives and false positives, while utilizing the fewest number of BEDS items. Starting with the initial BEDS item pool (20 items), the 13-item pilot BEDS resulted from the cognitive debriefing interviews (n = 13). Of the 97 participants in the noninterventional study, 16 were diagnosed with BED (10/62 female, 16%; 6/35 male, 17%). Seven BEDS items (BEDS-7) yielded 100% sensitivity and 38.7% specificity. Participants correctly identified (true positives) had poorer BES scores and RAND-36 scores than participants identified as true negatives. Implementation of the brief, patient-reported BEDS-7 in real-world clinical practice is expected to promote better understanding of BED characteristics and help physicians identify patients who may have BED.

Deposition of Suspended Clay to Open and Sand-Filled Framework Gravel Beds in a Laboratory Flume

NASA Astrophysics Data System (ADS)

Mooneyham, Christian; Strom, Kyle

2018-01-01

Pulses of fine sediment composed of sand, silt, and clay can be introduced to gravel bed rivers through runoff from burn-impacted hillslopes, landslides, bank failure, or the introduction of reservoir sediment as a result of sluicing or dam decommissioning. Here we present a study aimed at quantifying exchange between suspensions of clay and gravel beds. The questions that motivate the work are: how do bed roughness and pore space characteristics, shear velocity (u∗), and initial concentration (C0) affect clay deposition on or within gravel beds? Where does deposition within these beds occur, and can deposited clay be resuspended while the gravel is immobile? We examine these questions in a laboratory flume using acrylic, open-framework gravel, and armored sand-gravel beds under conditions of varying u∗ and C0. Deposition of clay occurred to all beds (even with Rouse numbers ˜ 0.01). We attribute deposition under full suspension conditions to be an outcome of localized protected zones where clay can settle and available pore space in the bed. For smooth wall cases, protection came from the viscous wall region and the development of bed forms; for the rough beds, protection came from separation zones and low-velocity pore spaces. Bed porosity was the strongest influencer of nondimensional deposition rate; deposition increased with porosity. Deposition was inversely related to u∗ for the acrylic bed runs; no influence of u∗ was found for the porous bed runs. Increases in discharge resulted in resuspension of clay from acrylic beds; no resuspension was observed in the porous bed runs.

Bacillus cereus in free-stall bedding.

PubMed

Magnusson, M; Svensson, B; Kolstrup, C; Christiansson, A

2007-12-01

To increase the understanding of how different factors affect the bacterial growth in deep sawdust beds for dairy cattle, the microbiological status of Bacillus cereus and coliforms in deep sawdust-bedded free stalls was investigated over two 14-d periods on one farm. High counts of B. cereus and coliforms were found in the entire beds. On average, 4.1 log(10) B. cereus spores, 5.5 log(10) B. cereus, and 6.7 log(10) coliforms per gram of bedding could be found in the upper layers of the sawdust likely to be in contact with the cows' udders. The highest counts of B. cereus spores, B. cereus, and coliforms were found in the bedding before fresh bedding was added, and the lowest immediately afterwards. Different factors of importance for the growth of B. cereus in the bedding material were explored in laboratory tests. These were found to be the type of bedding, pH, and the type and availability of nutrients. Alternative bedding material such as peat and mixtures of peat and sawdust inhibited the bacterial growth of B. cereus. The extent of growth of B. cereus in the sawdust was increased in a dose-dependent manner by the availability of feces. Urine added to different bedding material raised the pH and also led to bacterial growth of B. cereus in the peat. In sawdust, a dry matter content greater than 70% was needed to lower the water activity to 0.95, which is needed to inhibit the growth of B. cereus. In an attempt to reduce the bacterial growth of B. cereus and coliforms in deep sawdust beds on the farm, the effect of giving bedding daily or a full replacement of the beds was studied. The spore count of B. cereus in the back part of the free stalls before fresh bedding was added was 0.9 log units lower in stalls given daily bedding than in stalls given bedding twice weekly. No effect on coliform counts was found. Replacement of the entire sawdust bedding had an effect for a short period, but by 1 to 2 mo after replacement, the counts of B. cereus spores in the beds had increased about 2 log units and were as high as they were before bed replacement. Therefore, free-stall management could, to a limited extent, reduce the content of B. cereus spores in the beds by daily bedding and entire bed replacement.

Bed Bugs FAQs

MedlinePlus

... Consultations, and General Public. Contact Us Parasites Home Bed Bugs FAQs Recommend on Facebook Tweet Share Compartir On ... are bed bugs treated and prevented? What are bed bugs? Bed bugs ( Cimex lectularius ) are small, flat, parasitic ...

Staged fluidized-bed combustion and filter system

DOEpatents

Mei, Joseph S.; Halow, John S.

1994-01-01

A staged fluidized-bed combustion and filter system for substantially reducing the quantity of waste through the complete combustion into ash-type solids and gaseous products. The device has two fluidized-bed portions, the first primarily as a combustor/pyrolyzer bed, and the second as a combustor/filter bed. The two portions each have internal baffles to define stages so that material moving therein as fluidized beds travel in an extended route through those stages. Fluidization and movement is achieved by the introduction of gases into each stage through a directional nozzle. Gases produced in the combustor/pyrolyzer bed are permitted to travel into corresponding stages of the combustor/filter bed through screen filters that permit gas flow but inhibit solids flow. Any catalyst used in the combustor/filter bed is recycled. The two beds share a common wall to minimize total volume of the system. A slightly modified embodiment can be used for hot gas desulfurization and sorbent regeneration. Either side-by-side rectangular beds or concentric beds can be used. The system is particularly suited to the processing of radioactive and chemically hazardous waste.

EPA-Registered Bed Bug Products

MedlinePlus

... Bugs EPA Registered Bed Bug Products EPA-Registered Bed Bug Products Resources Bed Bug Main Page Top Ten ... Where you can use the pesticide Pesticide type Bed Bug Search Tool Enter the information as described in ...

Health Information in Oromo (Afan Oromoo)

MedlinePlus

... Section Bed Bugs Bed Bug Control in Residences - English PDF Bed Bug Control in Residences - Afan Oromoo ( ... Department of Agriculture Vacuuming to Capture Bed Bugs - English PDF Vacuuming to Capture Bed Bugs - Afan Oromoo ( ...

General and food-specific inhibitory deficits in binge eating disorder.

PubMed

Svaldi, Jennifer; Naumann, Eva; Trentowska, Monika; Schmitz, Florian

2014-07-01

To investigate behavioral inhibition in individuals with binge eating disorder (BED) compared with overweight and obese individuals without BED (No-BED). Participants with BED (n = 31) and the weight-matched No-BED group (n = 29) completed an inhibitory control task (stop-signal task, SST) with food and neutral stimuli. The BED group needed more time to stop an ongoing response, as indicated by increased stop signal reaction time (SSRT) relative to the No-BED group. Additionally, compared with the No-BED group, the BED group displayed more difficulty inhibiting responses elicited by food stimuli. The deficits in behavioral response inhibition were also found to be related to the severity of reported symptoms. There is a general deficit in late stage behavioral inhibition in BED, and this may be particularly pronounced in the context of food stimuli. © 2014 Wiley Periodicals, Inc.

Thermal enhancement cartridge heater modified (TECH Mod) tritium hydride bed development, Part 1 - Design and fabrication

DOE Office of Scientific and Technical Information (OSTI.GOV)

Klein, J.E.; Estochen, E.G.

The Savannah River Site (SRS) tritium facilities have used first generation (Gen1) LaNi{sub 4.25}Al{sub 0.75} (LANA0.75) metal hydride storage beds for tritium absorption, storage, and desorption. The Gen1 design utilizes hot and cold nitrogen supplies to thermally cycle these beds. Second and third generation (Gen2 and Gen3) storage bed designs include heat conducting foam and divider plates to spatially fix the hydride within the bed. For thermal cycling, the Gen2 and Gen3 beds utilize internal electric heaters and glovebox atmosphere flow over the bed inside the bed external jacket for cooling. The currently installed Gen1 beds require replacement due tomore » tritium aging effects on the LANA0.75 material, and cannot be replaced with Gen2 or Gen3 beds due to different designs of these beds. At the end of service life, Gen1 bed desorption efficiencies are limited by the upper temperature of hot nitrogen supply. To increase end-of-life desorption efficiency, the Gen1 bed design was modified, and a Thermal Enhancement Cartridge Heater Modified (TECH Mod) bed was developed. Internal electric cartridge heaters in the new design to improve end-of-life desorption, and also permit in-bed tritium accountability (IBA) calibration measurements to be made without the use of process tritium. Additional enhancements implemented into the TECH Mod design are also discussed. (authors)« less

THERMAL ENHANCEMENT CARTRIDGE HEATER MODIFIED TECH MOD TRITIUM HYDRIDE BED DEVELOPMENT PART I DESIGN AND FABRICATION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Klein, J.; Estochen, E.

The Savannah River Site (SRS) tritium facilities have used 1{sup st} generation (Gen1) LaNi{sub 4.25}Al{sub 0.75} (LANA0.75) metal hydride storage beds for tritium absorption, storage, and desorption. The Gen1 design utilizes hot and cold nitrogen supplies to thermally cycle these beds. Second and 3{sup rd} generation (Gen2 and Gen3) storage bed designs include heat conducting foam and divider plates to spatially fix the hydride within the bed. For thermal cycling, the Gen2 and Gen 3 beds utilize internal electric heaters and glovebox atmosphere flow over the bed inside the bed external jacket for cooling. The currently installed Gen1 beds requiremore » replacement due to tritium aging effects on the LANA0.75 material, and cannot be replaced with Gen2 or Gen3 beds due to different designs of these beds. At the end of service life, Gen1 bed desorption efficiencies are limited by the upper temperature of hot nitrogen supply. To increase end-of-life desorption efficiency, the Gen1 bed design was modified, and a Thermal Enhancement Cartridge Heater Modified (TECH Mod) bed was developed. Internal electric cartridge heaters in the new design to improve end-of-life desorption, and also permit in-bed tritium accountability (IBA) calibration measurements to be made without the use of process tritium. Additional enhancements implemented into the TECH Mod design are also discussed.« less

Petrology and geochemistry of samples from bed-contact zones in Tunnel Bed 5, U12g-Tunnel, Nevada Test Site

DOE Office of Scientific and Technical Information (OSTI.GOV)

Connolly, J.R.; Keil, K.; Mansker, W.L.

1984-10-01

This report summarizes the detailed geologic characterization of samples of bed-contact zones and surrounding nonwelded bedded tuffs, both within Tunnel Bed 5, that are exposed in the G-Tunnel complex beneath Rainier Mesa on the Nevada Test Site (NTS). Original planning studies treated the bed-contact zones in Tunnel Bed 5 as simple planar surfaces of relatively high permeability. Detailed characterization, however, indicates that these zones have a finite thickness, are depositional in origin, vary considerably over short vertical and horizontal distances, and are internally complex. Fluid flow in a sequence of nonwelded zeolitized ash-flow or bedded tuffs and thin intervening reworkedmore » zones appears to be a porous-medium phenomenon, regardless of the presence of layering. There are no consistent differences in either bulk composition or detailed mineralogy between bedded tuffs and bed-contact zones in Tunnel Bed 5. Although the original bulk composition of Tunnel Bed 5 was probably peralkaline, extensive zeolitization has resulted in a present peraluminous bulk composition of both bedded tuffs and bed-contact zones. The major zeolite present, clinoptilolite, is intermediate (Ca:K:Na = 26:35:39) and effectively uniform in composition. This composition is similar to that of clinoptilolite from the tuffaceous beds of Calico Hills above the static water level in hole USW G-1, but somewhat different from that reported for zeolites from below the static water level in USW G-2. Tunnel Bed 5 also contains abundant hydrous manganese oxides. The similarity in composition of the clinoptilolites from Tunnel Bed 5 and those above the static water level at Yucca Mountain indicates that many of the results of nuclide-migration experiments in Tunnel Bed 5 would be transferrable to zeolitized nonwelded tuffs above the static water level at Yucca Mountain.« less

CFD-DEM study of effect of bed thickness for bubbling fluidized beds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tingwen, Li; Gopalakrishnan, Pradeep; Garg, Rahul

2011-10-01

The effect of bed thickness in rectangular fluidized beds is investigated through the CFD–DEM simulations of small-scale systems. Numerical results are compared for bubbling fluidized beds of various bed thicknesses with respect to particle packing, bed expansion, bubble behavior, solids velocities, and particle kinetic energy. Good two-dimensional (2D) flow behavior is observed in the bed having a thickness of up to 20 particle diameters. However, a strong three-dimensional (3D) flow behavior is observed in beds with a thickness of 40 particle diameters, indicating the transition from 2D flow to 3D flow within the range of 20–40 particle diameters. Comparison ofmore » velocity profiles near the walls and at the center of the bed shows significant impact of the front and back walls on the flow hydrodynamics of pseudo-2D fluidized beds. Hence, for quantitative comparison with experiments in pseudo-2D columns, the effect of walls has to be accounted for in numerical simulations.« less

Method and apparatus for a combination moving bed thermal treatment reactor and moving bed filter

DOEpatents

Badger, Phillip C.; Dunn, Jr., Kenneth J.

2015-09-01

A moving bed gasification/thermal treatment reactor includes a geometry in which moving bed reactor particles serve as both a moving bed filter and a heat carrier to provide thermal energy for thermal treatment reactions, such that the moving bed filter and the heat carrier are one and the same to remove solid particulates or droplets generated by thermal treatment processes or injected into the moving bed filter from other sources.

Control of bed height in a fluidized bed gasification system

DOEpatents

Mehta, Gautam I.; Rogers, Lynn M.

1983-12-20

In a fluidized bed apparatus a method for controlling the height of the fdized bed, taking into account variations in the density of the bed. The method comprises taking simultaneous differential pressure measurements at different vertical elevations within the vessel, averaging the differential pressures, determining an average fluidized bed density, then periodically calculating a weighting factor. The weighting factor is used in the determination of the actual bed height which is used in controlling the fluidizing means.

Evaluation of a clay-based acidic bedding conditioner for dairy cattle bedding.

PubMed

Proietto, R L; Hinckley, L S; Fox, L K; Andrew, S M

2013-02-01

This study investigated the effects of a clay-based acidic bedding conditioner on sawdust bedding pH, dry matter (DM), environmental pathogen counts, and environmental bacterial counts on teat ends of lactating dairy cows. Sixteen lactating Holstein cows were paired based on parity, days in milk, milk yield, and milk somatic cell count, and were negative for the presence of an intramammary pathogen. Within each pair, cows were randomly assigned to 1 of 2 treatments with 3-wk periods in a crossover design. Treatment groups consisted of 9 freestalls per group bedded with either untreated sawdust or sawdust with a clay-based acidic bedding conditioner, added at 3- to 4-d intervals over each 21-d period. Bedding and teat ends were aseptically sampled on d 0, 1, 2, 7, 14, and 21 for determination of environmental bacterial counts. At the same time points, bedding was sampled for DM and pH determination. The bacteria identified in the bedding material were total gram-negative bacteria, Streptococcus spp., and coliform bacteria. The bacteria identified on the teat ends were Streptococcus spp., coliform bacteria, and Klebsiella spp. Teat end score, milk somatic cell count, and intramammary pathogen presence were measured weekly. Bedding and teat cleanliness, environmental high and low temperatures, and dew point data were collected daily. The bedding conditioner reduced the pH, but not the DM, of the sawdust bedding compared with untreated sawdust. Overall environmental bacterial counts in bedding were lower for treated sawdust. Total bacterial counts in bedding and on teat ends increased with time over both periods. Compared with untreated sawdust, the treated bedding had lower counts of total gram-negative bacteria and streptococci, but not coliform counts. Teat end bacterial counts were lower for cows bedded on treated sawdust for streptococci, coliforms, and Klebsiella spp. compared with cows bedded on untreated sawdust. The clay-based acidic bedding conditioner reduced environmental pathogens in sawdust bedding and teat ends without affecting teat end integrity. Copyright © 2013 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Trends in the supply of California’s emergency departments and inpatient services, 2005–2014: a retrospective analysis

PubMed Central

Chow, Jessica L; Niedzwiecki, Matthew J; Hsia, Renee Y

2017-01-01

Objectives Given increasing demand for emergency care, there is growing concern over the availability of emergency department (ED) and inpatient resources. Existing studies of ED bed supply are dated and often overlook hospital capacity beyond ED settings. We described recent statewide trends in the capacity of ED and inpatient hospital services from 2005 to 2014. Design Retrospective analysis. Setting Using California hospital data, we examined the absolute and per admission changes in ED beds and inpatient beds in all hospitals from 2005 to 2014. Participants Our sample consisted of all patients inpatient and outpatient) from 501 hospital facilities over 10-year period. Outcome measures We analysed linear trends in the total annual ED visits, ED beds, licensed and staffed inpatient hospital beds and bed types, ED beds per ED visit, and inpatient beds per admission (ED and non-ED). Results Between 2005 and 2014, ED visits increased from 9.8 million to 13.2 million (an increase of 35.0%, p<0.001). ED beds also increased (by 29.8%, p<0.001), with an average annual increase of 195.4 beds. Despite this growth, ED beds per visit decreased by 3.9%, from 6.0 ED beds per 10 000 ED visits in 2005 to 5.8 beds in 2014 (p=0.01). While overall admission numbers declined by 4.9% (p=0.06), inpatient medical/surgical beds per visit grew by 11.3%, from 11.6 medical/surgical beds per 1000 admissions in 2005 to 12.9 beds in 2014 (p<0.001). However, there were reductions in psychiatric and chemical dependency beds per admission, by −15.3% (p<0.001) and −22.4% (p=0.05), respectively. Conclusions These trends suggest that, in its current state, inadequate supply of ED and specific inpatient beds cannot keep pace with growing patient demand for acute care. Analysis of ED and inpatient supply should capture dynamic variations in patient demand. Our novel ‘beds pervisit’ metric offers improvements over traditional supply measures. PMID:28495813

Use of soft hydrothermal processing to improve and recycle bedding for laboratory animals.

PubMed

Miyamoto, T; Li, Z; Kibushi, T; Yamasaki, N; Kasai, N

2008-10-01

Cage bedding for laboratory rodents can influence animal wellbeing and thus the experimental data. In addition, a large amount of used bedding containing excrement is discharged as medical waste from life science institutes and breeding companies. We developed a ground-breaking system to improve fresh bedding and recycle used bedding by applying a soft hydrothermal process with high-temperature and high-pressure dry steam. The system removes both harmful organic components and aromatic hydrocarbons that can affect animals' metabolism. The purpose of the present study was to evaluate the chemical and physical properties of the improved fresh bedding and the recycled used bedding treated by the system. The results showed that 68-99% of the predominant aromatic hydrocarbons were removed from fresh bedding treated at 0.35 MPa and 140 degrees C for 120 min ('improved bedding'). In addition, 59.4-99.0% of predominant harmful organic compounds derived from excrement were removed from used bedding treated at 0.45 MPa and 150 degrees C for 60 min ('recycled bedding'). The soft hydrothermal treatment increased the number of acidic functional groups on the bedding surface and gave it the high adsorptive efficiency of ammonia gas. Harmful substances such as microorganisms, heavy metals and pesticides decreased below the detection limit. The results clearly showed that the improved and recycled bedding is safer for laboratory rodents and has the potential to ameliorate conditions in primary and secondary enclosures (e.g. cages and animal rooms) used for maintaining laboratory animals. This process may be one of the most advanced techniques in providing an alternative to softwood and other bedding, economizing through the recycling of used bedding and reducing bedding waste from animal facilities.

Diagnosing binge eating disorder in a primary care setting.

PubMed

Montano, C Brendan; Rasgon, Natalie L; Herman, Barry K

2016-01-01

Binge eating disorder (BED), now recognized as a distinct eating disorder in the Diagnostic and Statistical Manual of Mental Disorders, Fifth Edition, is the most prevalent eating disorder. Although nearly half of individuals with BED are obese, BED also occurs in nonobese individuals. Despite the relatively high percentage of weight loss treatment-seeking individuals meeting BED criteria, primary care physicians may not be familiar with or have ever diagnosed BED. Many providers may also have difficulty distinguishing BED as a contributory factor in obesity. This review differentiates BED from other causes of obesity by describing how obese individuals with BED differ from obese individuals without BED and from nonobese individuals with BED in areas including psychopathology, behavior, genetics, physiology, quality of life and productivity. The ways in which health-care providers can identify individuals who may have BED are also highlighted so the proper course of treatment is pursued. Overall, obese individuals with BED demonstrate a number of key characteristics that differentiate them from obese individuals without eating disorders, including increased impulsivity in response to food stimuli with loss of control over eating, resulting in the consumption of more calories. They also experience significant guilt and other negative emotions following a meal. In addition, individuals with BED patients have more psychiatric comorbidity, display more psychopathology, exhibit longer binge durations, consume more meals as snacks during the day and have less dietary restraint compared with individuals with BED who are not obese. However, the differences between individuals with BED who are obese versus not obese are not as prominent. Taken together, the evidence appears to support the conclusion that BED is a unique and treatable neurobehavioral disorder associated with distinct behavioral and psychological profiles and distinct medical and functional outcomes, and that it is not merely a subtype of obesity.

Collaborative Strategy on Bed Bugs

EPA Pesticide Factsheets

The Collaborative Strategy on Bed Bugs was developed by the Federal Bed Bug Workgroup to clarify the federal role in bed bug control and highlight ways that government, community, academia and private industry can work together on bed bug issues.

'My friends love to tan': examining sensation seeking and the mediating role of association with friends who use tanning beds on tanning bed use intentions.

PubMed

Banerjee, Smita C; Greene, Kathryn; Bagdasarov, Zhanna; Campo, Shelly

2009-12-01

This paper explored how sensation seeking contributes to the likelihood of tanning bed use intentions both directly and indirectly through the way it shapes interaction with peers who use tanning beds and attitudes toward tanning bed. Eight hundred and ninety six (n = 896) male and female college students were recruited for the study. Measured variables included sensation seeking, association with friends who use tanning beds, attitudes toward tanning and tanning bed use intentions. Structural equation modeling was performed to test the hypotheses. In general, results supported the proposed hypotheses and documented that sensation seeking is indirectly associated with tanning bed use intentions through the mediation of association with peers who use tanning beds and attitudes toward tanning. The article discusses theoretical and methodological implications of the findings demonstrating the pathways of influence of sensation seeking on tanning bed use intentions.

The Safety of Hospital Beds

PubMed Central

Gervais, Pierre; Pooler, Charlotte; Merryweather, Andrew; Doig, Alexa K.; Bloswick, Donald

2015-01-01

To explore the safety of the standard and the low hospital bed, we report on a microanalysis of 15 patients’ ability to ingress, move about the bed, and egress. The 15 participants were purposefully selected with various disabilities. Bed conditions were randomized with side rails up or down and one low bed with side rails down. We explored the patients’ use of the side rails, bed height, ability to lift their legs onto the mattress, and ability to turn, egress, and walk back to the chair. The standard bed was too high for some participants, both for ingress and egress. Side rails were used by most participants when entering, turning in bed, and exiting. We recommend that side rails be reconsidered as a means to facilitate in-bed movement, ingress, and egress. Furthermore, single deck height settings for all patients are not optimal. Low beds as a safety measure must be re-evaluated. PMID:28462302

Exploring the Early Structure of a Rapidly Decompressed Particle Bed

NASA Astrophysics Data System (ADS)

Zunino, Heather; Adrian, R. J.; Clarke, Amanda; Johnson, Blair; Arizona State University Collaboration

2017-11-01

Rapid expansion of dense, pressurized beds of fine particles subjected to rapid reduction of the external pressure is studied in a vertical shock tube. A near-sonic expansion wave impinges on the particle bed-gas interface and rapidly unloads the particle bed. A high-speed video camera captures events occurring during bed expansion. The particle bed does not expand homogeneously, but breaks down into horizontal slabs and then transforms into a cellular-type structure. There are several key parameters that affect the particle bed evolution, including particle size and initial bed height. Analyses of this bed structure evolution from experiments with varying particle sizes and initial bed heights is presented. This work is supported by the U.S. Department of Energy, National Nuclear Security Administration, Advanced Simulation and Computing Program, as a Cooperative Agreement under the Predictive Science and Academic Alliance Program, under Contract No. DE-NA0002378.

Method of shielding a liquid-metal-cooled reactor

DOEpatents

Sayre, Robert K.

1978-01-01

The primary heat transport system of a nuclear reactor -- particularly for a liquid-metal-cooled fast-breeder reactor -- is shielded and protected from leakage by establishing and maintaining a bed of a powdered oxide closely and completely surrounding all components thereof by passing a gas upwardly therethrough at such a rate as to slightly expand the bed to the extent that the components of the system are able to expand without damage and yet the particles of the bed remain close enough so that the bed acts as a guard vessel for the system. Preferably the gas contains 1 to 10% oxygen and the gas is passed upwardly through the bed at such a rate that the lower portion of the bed is a fixed bed while the upper portion is a fluidized bed, the line of demarcation therebetween being high enough that the fixed bed portion of the bed serves as guard vessel for the system.

Hybrid fluidized bed combuster

DOEpatents

Kantesaria, Prabhudas P.; Matthews, Francis T.

1982-01-01

A first atmospheric bubbling fluidized bed furnace is combined with a second turbulent, circulating fluidized bed furnace to produce heat efficiently from crushed solid fuel. The bed of the second furnace receives the smaller sizes of crushed solid fuel, unreacted limestone from the first bed, and elutriated solids extracted from the flu gases of the first bed. The two-stage combustion of crushed solid fuel provides a system with an efficiency greater than available with use of a single furnace of a fluidized bed.

Solid fuel feed system for a fluidized bed

DOEpatents

Jones, Brian C.

1982-01-01

A fluidized bed for the combustion of coal, with limestone, is replenished with crushed coal from a system discharging the coal laterally from a station below the surface level of the bed. A compartment, or feed box, is mounted at one side of the bed and its interior separated from the bed by a weir plate beneath which the coal flows laterally into the bed while bed material is received into the compartment above the plate to maintain a predetermined minimum level of material in the compartment.

Fluid bed material transfer method

DOEpatents

Pinske, Jr., Edward E.

1994-01-01

A fluidized bed apparatus comprising a pair of separated fluid bed enclosures, each enclosing a fluid bed carried on an air distributor plate supplied with fluidizing air from below the plate. At least one equalizing duct extending through sidewalls of both fluid bed enclosures and flexibly engaged therewith to communicate the fluid beds with each other. The equalizing duct being surrounded by insulation which is in turn encased by an outer duct having expansion means and being fixed between the sidewalls of the fluid bed enclosures.

Apparatus and process for controlling fluidized beds

DOEpatents

Rehmat, Amirali G.; Patel, Jitendra G.

1985-10-01

An apparatus and process for control and maintenance of fluidized beds under non-steady state conditions. An ash removal conduit is provided for removing solid particulates from a fluidized bed separate from an ash discharge conduit in the lower portion of the grate supporting such a bed. The apparatus and process of this invention is particularly suitable for use in ash agglomerating fluidized beds and provides control of the fluidized bed before ash agglomeration is initiated and during upset conditions resulting in stable, sinter-free fluidized bed maintenance.

Apparatus for controlling fluidized beds

DOEpatents

Rehmat, Amirali G.; Patel, Jitendra G.

1987-05-12

An apparatus and process for control and maintenance of fluidized beds under non-steady state conditions. An ash removal conduit is provided for removing solid particulates from a fluidized bed separate from an ash discharge conduit in the lower portion of the grate supporting such a bed. The apparatus and process of this invention is particularly suitable for use in ash agglomerating fluidized beds and provides control of the fluidized bed before ash agglomeration is initiated and during upset conditions resulting in stable, sinter-free fluidized bed maintenance.

Paediatric burn unit in Portugal: Beds needed using a bed-day approach.

PubMed

Santos, João V; Viana, João; Amarante, José; Freitas, Alberto

2017-03-01

Despite the high burden of children with burns, there is not a paediatric burn unit (PBU) in Portugal. We aimed to estimate the Portuguese health care providing needs on paediatric burns. We performed a nation-wide retrospective study, between 2009 and 2013, among less than 16 years-old inpatients with burns that met the transfer criteria to a burn unit in Portugal. A bed-day approach was used, targeting an occupancy rate of 70-75%, and possible locations were studied. The primary outcome was the number of beds needed, and secondary outcomes were the overload and revenue for each possible number of beds in a PBU. A total of 1155 children met the transfer criteria to a burn unit, representing a total of 17,371 bed-days. Occupancy rates of 11-bed, 12-bed, 13-bed and 14-bed PBU were, respectively, 79.7%, 75.3%, 71.0% and 66.8%. The 13-bed PBU scenario would represent an overload of 523 bed-days, revenue of more than 5 million Euros and a ratio of 1 PBU bed per 123,409 children. Using a groundbreaking approach, the optimal number of PBU beds needed in Portugal is 13. However, as half of the patients who met burn transfer criteria are not transferred, this bed number might be overestimated if this pattern maintains, despite the underestimation with our method approach. If a PBU is to be created the preferable location is Porto. Cost-effectiveness studies should be performed. Copyright © 2016 Elsevier Ltd and ISBI. All rights reserved.

Implications of lessons learned from tobacco control for tanning bed reform.

PubMed

Sinclair, Craig; Makin, Jennifer K

2013-01-01

Tanning beds used according to the manufacturer's instructions expose the user to health risks, including melanoma and other skin cancers. Applying the MPOWER model (monitor, protect, offer alternatives, warn, enforce, and raise taxes), which has been used in tobacco control, to tanning bed reform could reduce the number of people at risk of diseases associated with tanning bed use. Among the tactics available to government are restricting the use of tanning beds by people under age 18 and those with fair skin, increasing the price of tanning bed services through taxation, licensing tanning bed operators, and banning unsupervised tanning bed operations.

Implications of Lessons Learned From Tobacco Control for Tanning Bed Reform

PubMed Central

Sinclair, Craig

2013-01-01

Tanning beds used according to the manufacturer’s instructions expose the user to health risks, including melanoma and other skin cancers. Applying the MPOWER model (monitor, protect, offer alternatives, warn, enforce, and raise taxes), which has been used in tobacco control, to tanning bed reform could reduce the number of people at risk of diseases associated with tanning bed use. Among the tactics available to government are restricting the use of tanning beds by people under age 18 and those with fair skin, increasing the price of tanning bed services through taxation, licensing tanning bed operators, and banning unsupervised tanning bed operations. PMID:23449282

Method of burning sulfur-containing fuels in a fluidized bed boiler

DOEpatents

Jones, Brian C.

1982-01-01

A method of burning a sulfur-containing fuel in a fluidized bed of sulfur oxide sorbent wherein the overall utilization of sulfur oxide sorbent is increased by comminuting the bed drain solids to a smaller average particle size, preferably on the order of 50 microns, and reinjecting the comminuted bed drain solids into the bed. In comminuting the bed drain solids, particles of spent sulfur sorbent contained therein are fractured thereby exposing unreacted sorbent surface. Upon reinjecting the comminuted bed drain solids into the bed, the newly-exposed unreacted sorbent surface is available for sulfur oxide sorption, thereby increasing overall sorbent utilization.

Testing a Threshold-Based Bed Bug Management Approach in Apartment Buildings.

PubMed

Singh, Narinderpal; Wang, Changlu; Zha, Chen; Cooper, Richard; Robson, Mark

2017-07-26

We tested a threshold-based bed bug ( Cimex lectularius L.) management approach with the goal of achieving elimination with minimal or no insecticide application. Thirty-two bed bug infested apartments were identified. These apartments were divided into four treatment groups based on apartment size and initial bed bug count, obtained through a combination of visual inspection and bed bug monitors: I- Non-chemical only in apartments with 1-12 bed bug count, II- Chemical control only in apartments with 1-12 bed bug count, III- Non-chemical and chemical control in apartments with >12 bed bug count, and IV- Chemical control only in apartments with ≥11 bed bug count. All apartments were monitored or treated once every two weeks for a maximum of 28 wk. Treatment I eliminated bed bugs in a similar amount of time to treatment II. Time to eliminate bed bugs was similar between treatment III and IV but required significantly less insecticide spray in treatment III than that in treatment IV. A threshold-based management approach (non-chemical only or non-chemical and chemical) can eliminate bed bugs in a similar amount of time, using little to no pesticide compared to a chemical only approach.

Mechanical stratigraphic controls on natural fracture spacing and penetration

NASA Astrophysics Data System (ADS)

McGinnis, Ronald N.; Ferrill, David A.; Morris, Alan P.; Smart, Kevin J.; Lehrmann, Daniel

2017-02-01

Fine-grained low permeability sedimentary rocks, such as shale and mudrock, have drawn attention as unconventional hydrocarbon reservoirs. Fracturing - both natural and induced - is extremely important for increasing permeability in otherwise low-permeability rock. We analyze natural extension fracture networks within a complete measured outcrop section of the Ernst Member of the Boquillas Formation in Big Bend National Park, west Texas. Results of bed-center, dip-parallel scanline surveys demonstrate nearly identical fracture strikes and slight variation in dip between mudrock, chalk, and limestone beds. Fracture spacing tends to increase proportional to bed thickness in limestone and chalk beds; however, dramatic differences in fracture spacing are observed in mudrock. A direct relationship is observed between fracture spacing/thickness ratio and rock competence. Vertical fracture penetrations measured from the middle of chalk and limestone beds generally extend to and often beyond bed boundaries into the vertically adjacent mudrock beds. In contrast, fractures in the mudrock beds rarely penetrate beyond the bed boundaries into the adjacent carbonate beds. Consequently, natural bed-perpendicular fracture connectivity through the mechanically layered sequence generally is poor. Fracture connectivity strongly influences permeability architecture, and fracture prediction should consider thin bed-scale control on fracture heights and the strong lithologic control on fracture spacing.

Efficacy of three different steamers for control of bed bugs (Cimex lectularius L.).

PubMed

Wang, Desen; Wang, Changlu; Wang, Guohong; Zha, Chen; Eiden, Amanda L; Cooper, Richard

2018-04-15

Bed bugs, Cimex lectularius L., have become one of the most difficult urban pests to control. Steam treatment is reported to be an effective method to kill bed bugs and is considered to be an important component of bed bug integrated pest management (IPM). We evaluated and compared the efficacy of two affordable consumer-grade commercial steamers to a commonly used professional-grade steamer for killing bed bugs. In laboratory experiments, the consumer-grade steamer at an affordable price achieved the same high control efficacy as the professional-grade steamer for treating bed bugs exposed on mattresses (100% bed bug mortality), located beneath a fabric cover (>89% bed bug mortality), or hiding in cracks (100% bed bug mortality). Bed bugs located behind a leather cover did not suffer significant mortality from steam treatment regardless of the type of steamers used and treatment duration. Proper use of steamers can kill all life stages of bed bugs. Affordable consumer-grade steamers are as effective as professional-grade steam machines for eliminating bed bugs resting on mattresses, hiding behind fabric materials, or in cracks. This article is protected by copyright. All rights reserved.

Tanning beds: A call to action for further educational and legislative efforts.

PubMed

Farley, Clara; Alimi, Yewande; Espinosa, Lauren R; Perez, Sebastian; Knechtle, William; Hestley, Andrea; Carlson, Grant W; Russell, Maria C; Delman, Keith A; Rizzo, Monica

2015-08-01

Melanoma is steadily increasing over the past decade. Recent studies confirmed a link between tanning bed use and melanoma. We sought to determine the prevalence and frequency of tanning bed among young patients with melanoma. We retrospectively analyzed tanning bed use among young melanoma patients compared to controls selected from the hospital medical records. A telephone survey investigated family history of melanoma or skin cancer, hair color, eye color, skin type, tanning bed use, and patient awareness of dangers of tanning bed use. A total of 601 melanoma cases were identified; 265 (44%) completed the telephone survey as did 195 (31%) controls. Of these 460 subjects, 260 were female. Females were 3.0 times more likely to have used a tanning bed. Melanoma patients had natural light color hair, blue-green eyes, and 2.0 times more likely to use a tanning bed than controls. Among the tanning bed users, 90% were aware of danger of tanning bed. Our study found that tanning beds were more likely to be used by young women, the majority of whom are aware of the associated risks. Eliminating the use of tanning beds should be considered to decrease the incidence of melanoma. © 2015 Wiley Periodicals, Inc.

Testing a Threshold-Based Bed Bug Management Approach in Apartment Buildings

PubMed Central

Singh, Narinderpal; Zha, Chen; Cooper, Richard; Robson, Mark

2017-01-01

We tested a threshold-based bed bug (Cimex lectularius L.) management approach with the goal of achieving elimination with minimal or no insecticide application. Thirty-two bed bug infested apartments were identified. These apartments were divided into four treatment groups based on apartment size and initial bed bug count, obtained through a combination of visual inspection and bed bug monitors: I- Non-chemical only in apartments with 1–12 bed bug count, II- Chemical control only in apartments with 1–12 bed bug count, III- Non-chemical and chemical control in apartments with >12 bed bug count, and IV- Chemical control only in apartments with ≥11 bed bug count. All apartments were monitored or treated once every two weeks for a maximum of 28 wk. Treatment I eliminated bed bugs in a similar amount of time to treatment II. Time to eliminate bed bugs was similar between treatment III and IV but required significantly less insecticide spray in treatment III than that in treatment IV. A threshold-based management approach (non-chemical only or non-chemical and chemical) can eliminate bed bugs in a similar amount of time, using little to no pesticide compared to a chemical only approach. PMID:28933720

Dosimetric quality endpoints for low-dose-rate prostate brachytherapy using biological effective dose (bed) vs. conventional dose

DOE Office of Scientific and Technical Information (OSTI.GOV)

Singh, Rachana; Al-Hallaq, Hania; Pelizzari, Charles A.

2003-12-31

The purpose of this study was to compare conventional low-dose-rate prostate brachytherapy dosimetric quality parameters with their biological effective dose (BED) counterparts. To validate a model for transformation from conventional dose to BED, the postimplant plans of 31 prostate brachytherapy patients were evaluated using conventional dose-volume histogram (DVH) quality endpoints and analogous BED-DVH endpoints. Based on CT scans obtained 4 weeks after implantation, DVHs were computed and standard dosimetric endpoints V100 (volume receiving 100% of the prescribed dose), V150, V200, HI (1-[V150/V100]), and D90 (dose that 90% of the target volume received) were obtained for quality analysis. Using known andmore » reported transformations, dose grids were transformed to BED-early ({alpha}/{beta} = 10 Gy) and BED-late ({alpha}/{beta} = 3 Gy) grids, and the same dosimetric endpoints were analyzed. For conventional, BED-early and BED-late DVHs, no differences in V100 were seen (0.896, 0.893, and 0.894, respectively). However, V150 and V200 were significantly higher for both BED-early (0.582 and 0.316) and BED-late (0.595 and 0.337), compared with the conventional (0.539 and 0.255) DVHs. D90 was significantly lower for the BED-early (103.1 Gy) and BED-late transformations (106.9 Gy) as compared with the conventional (119.5 Gy) DVHs. The conventional prescription parameter V100 is the same for the corresponding BED-early and BED-late transformed DVHs. The toxicity parameters V150 and V200 are slightly higher using the BED transformations, suggesting that the BED doses are somewhat higher than predicted using conventional DVHs. The prescription/quality parameter D90 is slightly lower, implying that target coverage is lower than predicted using conventional DVHs. This methodology can be applied to analyze BED dosimetric endpoints to improve clinical outcome and reduce complications of prostate brachytherapy.« less

Discrete Element Modeling of the Mobilization of Coarse Gravel Beds by Finer Gravel Particles

NASA Astrophysics Data System (ADS)

Hill, K. M.; Tan, D.

2012-12-01

Recent research has shown that the addition of fine gravel particles to a coarse bed will mobilize the coarser bed, and that the effect is sufficiently strong that a pulse of fine gravel particles can mobilize an impacted coarser bed. Recent flume experiments have demonstrated that the degree of bed mobilization by finer particles is primarily dependent on the particle size ratio of the coarse and fine particles, rather than absolute size of either particle, provided both particles are sufficiently large. However, the mechanism behind the mobilization is not understood. It has previously been proposed that the mechanism is driven by a combination of geometric effects and hydraulic effects. For example, it has been argued that smaller particles fill in gaps along the bed, resulting in a smoother bed over which the larger particles are less likely to be disentrained and a reduced near-bed flow velocity and subsequent increased drag on protruding particles. Altered near-bed turbulence has also been cited as playing an important role. We perform simulations using the discrete element method with one-way fluid-solid coupling to conduct simulations of mobilization of a gravel bed by fine gravel particles. By independently and artificially controlling average and fluctuating velocity profiles, we systematically investigate the relative role that may be played by particle-particle interactions, average near-bed velocity profiles, and near-bed turbulence statistics. The simulations indicate that the relative importance of these mechanisms changes with the degree of mobilization of the bed. For higher bed mobility similar to bed sheets, particle-particle interactions, plays a significant role in an apparent rheology in the bed sheets, not unlike that observed in a dense granular flow of particles of different sizes. For conditions closer to a critical shear stress for bedload transport, the near-bed velocity profiles and turbulence statistics become increasingly important.

Cognitive Rationalizations for Tanning-Bed Use: A Preliminary Exploration

PubMed Central

Banerjee, Smita C.; Hay, Jennifer L.; Greene, Kathryn

2016-01-01

Objectives To examine construct and predictive utility of an adapted cognitive rationalization scale for tanning-bed use. Methods Current/former tanning-bed-using undergraduate students (N = 216; 87.6% females; 78.4% white) at a large northeastern university participated in a survey. A cognitive rationalization for tanning-bed use scale was adapted. Standardized self-report measures of past tanning-bed use, advantages of tanning, perceived vulnerability to photoaging, tanning-bed use dependence, and tanning- bed use intention were also administered. Results The cognitive rationalization scale exhibited strong construct and predictive validity. Current tanners and tanning-bed-use-dependent participants endorsed rationalizations more strongly than did former tanners and not-tanning-bed-use-dependent participants respectively. Conclusions Findings indicate that cognitive rationalizations help explain discrepancy between inconsistent cognitions. PMID:23985280

Updated Performance Evaluation of the ISS Water Processor Multifiltration Beds

NASA Technical Reports Server (NTRS)

Bowman, Elizabeth M.; Carter, Layne; Carpenter, Joyce; Orozco, Nicole; Weir, Natalee; Wilson, Mark

2014-01-01

The ISS Water Processor Assembly (WPA) produces potable water from a waste stream containing humidity condensate and urine distillate. The primary treatment process is achieved in the Multifiltration Beds, which include adsorbent media and ion exchange resin for the removal of dissolved organic and inorganic contaminants. Two Multifiltration Beds (MF Beds) were replaced on ISS in July 2010 after initial indication of inorganic breakthrough of the first bed and an increasing Total Organic Carbon (TOC) trend in the product water. The first bed was sampled and analyzed Sept 2011 through March 2012. The second MF Bed was sampled and analyzed June 2012 through August 2012. The water resident in the both beds was analyzed for various parameters to evaluate adsorbent loading, performance of the ion exchange resin, microbial activity, and generation of leachates from the ion exchange resin. Portions of the adsorbent media and ion exchange resin were sampled and subsequently desorbed to identify the primary contaminants removed at various points in the bed in addition to microbial analysis. Analysis of the second bed will be compared to results from the first bed to provide a comprehensive overview of how the Multifiltration Beds function on orbit. New data from the second bed supplements the analysis of the first bed (previously reported) and gives a more complete picture of breakthrough compounds, resin breakdown products, microbial activity, and difficult to remove compounds. The results of these investigations and implications to the operation of the WPA on ISS are documented in this paper.

77 FR 12182 - Safety Standard for Portable Bed Rails: Final Rule

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-29

... of ASTM F2085- 10a, comply with the following: (i) 1.4.1 Foam and inflatable bed rails need meet only...--portable bed rail constructed primarily of nonrigid materials such as fabric or foam. 3.1.11 inflatable bed..., inflatable bed rail, are terms that are now incorporated as non-rigid bed rail under new section 3.1.12 in...

Role of Vision and Mechanoreception in Bed Bug, Cimex lectularius L. Behavior

PubMed Central

Singh, Narinderpal; Wang, Changlu; Cooper, Richard

2015-01-01

The role of olfactory cues such as carbon dioxide, pheromones, and kairomones in bed bug, Cimex lectularius L. behavior has been demonstrated. However, the role of vision and mechanoreception in bed bug behavior is poorly understood. We investigated bed bug vision by determining their responses to different colors, vertical objects, and their ability to detect colors and vertical objects under low and complete dark conditions. Results show black and red paper harborages are preferred compared to yellow, green, blue, and white harborages. A bed bug trapping device with a black or red exterior surface was significantly more attractive to bed bugs than that with a white exterior surface. Bed bugs exhibited strong orientation behavior toward vertical objects. The height (15 vs. 30 cm tall) and color (brown vs. black) of the vertical object had no significant effect on orientation behavior of bed bugs. Bed bugs could differentiate color and detect vertical objects at very low background light conditions, but not in complete darkness. Bed bug preference to different substrate textures (mechanoreception) was also explored. Bed bugs preferred dyed tape compared to painted tape, textured painted plastic, and felt. These results revealed that substrate color, presence of vertical objects, and substrate texture affect host-seeking and harborage-searching behavior of bed bugs. Bed bugs may use a combination of vision, mechanoreception, and chemoreception to locate hosts and seek harborages. PMID:25748041

Coevolution of bed surface patchiness and channel morphology: 2. Numerical experiments

USGS Publications Warehouse

Nelson, Peter A.; McDonald, Richard R.; Nelson, Jonathan M.; Dietrich, William E.

2015-01-01

In gravel bed rivers, bed topography and the bed surface grain size distribution evolve simultaneously, but it is not clear how feedbacks between topography and grain sorting affect channel morphology. In this, the second of a pair of papers examining interactions between bed topography and bed surface sorting in gravel bed rivers, we use a two-dimensional morphodynamic model to perform numerical experiments designed to explore the coevolution of both free and forced bars and bed surface patches. Model runs were carried out on a computational grid simulating a 200 m long, 2.75 m wide, straight, rectangular channel, with an initially flat bed at a slope of 0.0137. Over five numerical experiments, we varied (a) whether an obstruction was present, (b) whether the sediment was a gravel mixture or a single size, and (c) whether the bed surface grain size feeds back on the hydraulic roughness field. Experiments with channel obstructions developed a train of alternate bars that became stationary and were connected to the obstruction. Freely migrating alternate bars formed in the experiments without channel obstructions. Simulations incorporating roughness feedbacks between the bed surface and flow field produced flatter, broader, and longer bars than simulations using constant roughness or uniform sediment. Our findings suggest that patches are not simply a by-product of bed topography, but they interact with the evolving bed and influence morphologic evolution.

Binge eating disorder and obesity: preliminary evidence for distinct cardiovascular and psychological phenotypes.

PubMed

Klatzkin, Rebecca R; Gaffney, Sierra; Cyrus, Kathryn; Bigus, Elizabeth; Brownley, Kimberly A

2015-04-01

This study investigated cardiovascular functioning, mood, and eating-related psychological factors at rest and in response to mental stress in three groups of women: 1) Obese women with binge eating disorder (BED; n=9); 2) obese non-BED women (n=15); and 3) normal weight (NW) non-BED women (n=15). Compared to both obese and NW non-BED women, obese women with BED showed heightened overall blood pressure and reported greater depression symptoms, perceived stress, and eating-related psychopathology. Additionally, obese women with BED reported greater overall negative affect and state anxiety compared to obese non-BED women. The heart rate response to stress was blunted in the obese BED group compared to the other groups, but this effect was no longer significant after controlling for baseline differences in depression. Correlational analyses revealed a positive association between stress-induced changes in hunger and cardiovascular measures only in obese women with BED. Longitudinal studies are needed to determine if stress dysregulation and stress-induced increases in hunger contribute to the onset and/or maintenance of BED. In particular, studies utilizing an additional NW BED control group are warranted in order to further examine the impact of BED above and beyond the impact of obesity on psychophysiological functioning and to inform the growing literature regarding stress-related factors that distinguish the BED and obesity phenotypes. Copyright © 2015 Elsevier Inc. All rights reserved.

Role of vision and mechanoreception in bed bug, Cimex lectularius L. behavior.

PubMed

Singh, Narinderpal; Wang, Changlu; Cooper, Richard

2015-01-01

The role of olfactory cues such as carbon dioxide, pheromones, and kairomones in bed bug, Cimex lectularius L. behavior has been demonstrated. However, the role of vision and mechanoreception in bed bug behavior is poorly understood. We investigated bed bug vision by determining their responses to different colors, vertical objects, and their ability to detect colors and vertical objects under low and complete dark conditions. Results show black and red paper harborages are preferred compared to yellow, green, blue, and white harborages. A bed bug trapping device with a black or red exterior surface was significantly more attractive to bed bugs than that with a white exterior surface. Bed bugs exhibited strong orientation behavior toward vertical objects. The height (15 vs. 30 cm tall) and color (brown vs. black) of the vertical object had no significant effect on orientation behavior of bed bugs. Bed bugs could differentiate color and detect vertical objects at very low background light conditions, but not in complete darkness. Bed bug preference to different substrate textures (mechanoreception) was also explored. Bed bugs preferred dyed tape compared to painted tape, textured painted plastic, and felt. These results revealed that substrate color, presence of vertical objects, and substrate texture affect host-seeking and harborage-searching behavior of bed bugs. Bed bugs may use a combination of vision, mechanoreception, and chemoreception to locate hosts and seek harborages.

Apparatus for controlling fluidized beds

DOEpatents

Rehmat, A.G.; Patel, J.G.

1987-05-12

An apparatus and process are disclosed for control and maintenance of fluidized beds under non-steady state conditions. An ash removal conduit is provided for removing solid particulates from a fluidized bed separate from an ash discharge conduit in the lower portion of the grate supporting such a bed. The apparatus and process of this invention is particularly suitable for use in ash agglomerating fluidized beds and provides control of the fluidized bed before ash agglomeration is initiated and during upset conditions resulting in stable, sinter-free fluidized bed maintenance. 2 figs.

Cross-bedding Related Anisotropy and its Role in the Orientation of Joints in an Aeolian Sandstone

NASA Astrophysics Data System (ADS)

Deng, S.; Cilona, A.; Mapeli, C.; Panfilau, A.; Aydin, A.; Prasad, M.

2014-12-01

Previous research revealed that the cross-bedding related anisotropy in aeolian sandstones affects the orientation of compaction bands, also known as anticracks. We hypothesize that cross-bedding should a have similar influence on the orientation of the joints within the same rock at the same location. To test this hypothesis, we investigated the relationship between the cross-beds and the cross-bed package confined joints in the Jurassic aeolian Aztec Sandstone cropping out in the Valley of Fire State Park, Nevada. The field data demonstrates that the cross-bed package confined joints occur at high-angle to bedding and trend roughly parallel to the dip direction of the cross-beds. This shows that the cross-bed orientation and the associated anisotropy also exert a strong control on the formation and orientation of the joints. In order to characterize the anisotropy due to cross-bedding in the Aztec Sandstone, we measured the P-wave velocities parallel and perpendicular to bedding from 11 samples in the laboratory using a bench-top ultrasonic assembly. The measured P-wave anisotropy is about 13% on average. Based on these results, a numerical model based on the generalized Hooke's law for anisotropic materials is analyzed assuming the cross-bedded sandstone to be transversely isotropic. Using this model, we tested various cross-bed orientations as well as different strain boundary conditions (uniaxial, axisymmetric and triaxial). It is possible to define a boundary condition under which the modeled results roughly match with the observed relationship between cross-bed package confined joints and cross-beds. These results have important implications for fluid flow through aeolian sandstones in reservoirs and aquifers.

Bed sharing among mother-infant pairs in Klang district, Peninsular Malaysia and its relationship to breast-feeding.

PubMed

Tan, Kok Leong

2009-10-01

The aim of the study was to determine the prevalence of mother-infant bed sharing in Klang district, Peninsular Malaysia and to identify factors associated with bed sharing. This was a cross-sectional study involving 682 mother-infant pairs with infants up to 6 months attending government clinics in Klang district, Peninsular Malaysia. Data were collected by face-to-face interview using a pretested structured questionnaire for a 4-month period in 2006. Data regarding maternal, paternal, obstetric, infant, occupancy, breast-feeding characteristics, and bed-sharing practice were collected. Data on bed sharing were based on practice in the past 1-month period. Bed sharing was defined as an infant sharing a bed with mother, and infant must be within arms reach from the mother, whereas a bed was defined as either a sleeping mattress placed on a bed frame or placed on the floor. The prevalence of bed sharing was estimated. Relationship and magnitude of association between independent factors and bed sharing were examined using odds ratio and 95% confidence interval. Logistic regression analysis was used to control for confounding factors. The prevalence of bed sharing among mothers with infants aged between 1 and 6 months was 73.5% (95% confidence interval: 70.0-76.7). In multivariate analysis, urban/rural differences, mothers' ethnicity, occupation, family income, husbands' support on bed sharing, number of children younger than 12 years staying in the house, and breast-feeding were associated with bed sharing. These factors need to be considered in analyzing the overall risks and benefits of bed sharing, paying attention to breastfeeding practices.

Mineral resources of the Devil's Garden Lava Bed, Squaw Ridge Lava Bed, and Four Craters Lava Bed Wilderness Study Areas, Lake County, Oregon

DOE Office of Scientific and Technical Information (OSTI.GOV)

Keith, W.J.; King, H.D.; Gettings, M.E.

1988-01-01

The Devel's Garden lava Bed, Squaw Ridge Lava Bed, and Four Craters Lava Bed Wilderness Study Areas include approximately 70,940 acres and are underlain entirely by Pleistocene or Holocene lava flows and associated sediments. There is no evidence of hydrothermal alteration in the study areas. No resources were identified in the study areas, but there is low potential for perlite resources in the southern part of the Devil's Garden Lava Bed and the northern half of the Squaw Ridge Lava Bed areas. All three study areas have low potential for geothermal resources and for oil and gas resources.

High-Flux, High Performance H2O2 Catalyst Bed for ISTAR

NASA Technical Reports Server (NTRS)

Ponzo, J.

2005-01-01

On NASA's ISTAR RBCC program packaging and performance requirements exceeded traditional H2O2 catalyst bed capabilities. Aerojet refined a high performance, monolithic 90% H202 catalyst bed previously developed and demonstrated. This approach to catalyst bed design and fabrication was an enabling technology to the ISTAR tri-fluid engine. The catalyst bed demonstrated 55 starts at throughputs greater than 0.60 lbm/s/sq in for a duration of over 900 seconds in a physical envelope approximately 114 of traditional designs. The catalyst bed uses photoetched plates of metal bonded into a single piece monolithic structure. The precise control of the geometry and complete mixing results in repeatable, quick starting, high performing catalyst bed. Three different beds were designed and tested, with the best performing bed used for tri-fluid engine testing.

77 FR 18793 - Spectrum Sharing Innovation Test-Bed Pilot Program

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-28

.... 120322212-2212-01] Spectrum Sharing Innovation Test-Bed Pilot Program AGENCY: National Telecommunications... Innovation Test-Bed pilot program to assess whether devices employing Dynamic Spectrum Access techniques can... Spectrum Sharing Innovation Test-Bed (Test-Bed) pilot program to examine the feasibility of increased...

The effect of bedding system selected by manual muscle testing on sleep-related cardiovascular functions.

PubMed

Kuo, Terry B J; Li, Jia-Yi; Lai, Chun-Ting; Huang, Yu-Chun; Hsu, Ya-Chuan; Yang, Cheryl C H

2013-01-01

Different types of mattresses affect sleep quality and waking muscle power. Whether manual muscle testing (MMT) predicts the cardiovascular effects of the bedding system was explored using ten healthy young men. For each participant, two bedding systems, one inducing the strongest limb muscle force (strong bedding system) and the other inducing the weakest limb force (weak bedding system), were identified using MMT. Each bedding system, in total five mattresses and eight pillows of different firmness, was used for two continuous weeks at the participant's home in a random and double-blind sequence. A sleep log, a questionnaire, and a polysomnography were used to differentiate the two bedding systems. Heart rate variability and arterial pressure variability analyses showed that the strong bedding system resulted in decreased cardiovascular sympathetic modulation, increased cardiac vagal activity, and increased baroreceptor reflex sensitivity during sleep as compared to the weak bedding system. Different bedding systems have distinct cardiovascular effects during sleep that can be predicted by MMT.

The Effect of Bedding System Selected by Manual Muscle Testing on Sleep-Related Cardiovascular Functions

PubMed Central

Kuo, Terry B. J.; Li, Jia-Yi; Lai, Chun-Ting; Huang, Yu-Chun; Hsu, Ya-Chuan; Yang, Cheryl C. H.

2013-01-01

Background. Different types of mattresses affect sleep quality and waking muscle power. Whether manual muscle testing (MMT) predicts the cardiovascular effects of the bedding system was explored using ten healthy young men. Methods. For each participant, two bedding systems, one inducing the strongest limb muscle force (strong bedding system) and the other inducing the weakest limb force (weak bedding system), were identified using MMT. Each bedding system, in total five mattresses and eight pillows of different firmness, was used for two continuous weeks at the participant's home in a random and double-blind sequence. A sleep log, a questionnaire, and a polysomnography were used to differentiate the two bedding systems. Results and Conclusion. Heart rate variability and arterial pressure variability analyses showed that the strong bedding system resulted in decreased cardiovascular sympathetic modulation, increased cardiac vagal activity, and increased baroreceptor reflex sensitivity during sleep as compared to the weak bedding system. Different bedding systems have distinct cardiovascular effects during sleep that can be predicted by MMT. PMID:24371836

Reduction of FeO contents in sinter under high bed operation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fujii, K.; Hazama, K.; Hoshikuma, Y.

1996-12-31

High-bed operation (bed height more than 700 mm) is currently being carried out at the Kure No. 1 sintering plant. Before initiating this high-bed operation, the authors conducted sinter pot tests at various bed heights to investigate the effect of bed height on sintering. The following results were obtained from these pot tests: Heightening of the sinter bed increased yield at the upper layer, but at the lower layer, the yield reached a maximum value at a certain bed height. From observation of the sinter cakes, the reduction in yield is attributed to uneven burn caused by surplus heat atmore » the lower layers. Therefore, when high-bed operation is carried out, reduction of the burning energy (reduction of the FeO content in the sinter) is required. This high-bed operation with lower FeO content has enabled the company to reduce fuel consumption and SiO{sub 2} content, while maintaining high yield and high sinter quality.« less

Stress-induced laboratory eating behavior in obese women with binge eating disorder.

PubMed

Laessle, Reinhold G; Schulz, Simone

2009-09-01

To compare the microstructural eating behavior of obese patients with and without binge eating disorder (BED) after stress induction in laboratory. Forty-eight obese women were investigated. Seventeen were assigned to the group of BED. Group (BED vs. non-BED) by condition (stress vs. no stress) interaction effect on feeding variables, measured by a universal eating monitor, was tested. Stress was induced by the trier social stress test (TSST) and chocolate pudding served as laboratory food. From the nonstress to the stress condition, patients with BED, when compared with non-BED had a greater increase in average eating rate (p < .01) and a corresponding greater increase in the frequency of spoonfuls (p < .02). The BED group also showed a different change in acceleration/deceleration from the nonstress to the stress condition compared to the non-BED group (p < .04). Obese individuals with BED appear to exhibit a different response to stress than obese non-BED individuals and individuals with bulimia nervosa.

Response of bed mobility to sediment supply in natural gravel bed channels: A detailed examination and evaluation of mobility parameters

Treesearch

T. E. Lisle; J. M. Nelson; B. L. Barkett; J. Pitlick; M. A. Madej

1998-01-01

Recent laboratory experiments have shown that bed mobility in gravel bed channels responds to changes in sediment supply, but detailed examinations of this adjustment in natural channels have been lacking, and practical methodologies to measure bed mobility have not been tested. We examined six gravel-bed, alternate-bar channels which have a wide range in annual...

Separation of particulate from flue gas of fossil fuel combustion and gasification

DOEpatents

Yang, W.C.; Newby, R.A.; Lippert, T.E.

1997-08-05

The gas from combustion or gasification of fossil fuel contains fly ash and other particulates. The fly ash is separated from the gas in a plurality of standleg moving granular-bed filter modules. Each module includes a dipleg through which the bed media flows into the standleg. The bed media forms a first filter bed having an upper mass having a first frusto-conical surface in a frusto-conical member at the entrance to the standleg and a lower mass having a second frusto-conical surface of substantially greater area than the first surface after it passes through the standleg. A second filter media bed may be formed above the first filter media bed. The gas is fed tangentially into the module above the first surface. The fly ash is captured on the first frusto-conical surface and within the bed mass. The processed gas flows out through the second frusto-conical surface and then through the second filter bed, if present. The bed media is cleaned of the captured fly ash and recirculated to the moving granular bed filter. Alternatively, the bed media may be composed of the ash from the combustion which is pelletized to form agglomerates. The ash flows through the bed only once; it is not recycled. 11 figs.

Separation of particulate from flue gas of fossil fuel combustion and gasification

DOEpatents

Yang, Wen-Ching; Newby, Richard A.; Lippert, Thomas E.

1997-01-01

The gas from combustion or gasification of fossil fuel contains flyash and other particulate. The flyash is separated from the gas in a plurality of standleg moving granular-bed filter modules. Each module includes a dipleg through which the bed media flows into the standleg. The bed media forms a first filter bed having an upper mass having a first frusto-conical surface in a frusto-conical member at the entrance to the standleg and a lower mass having a second frusto-conical surface of substantially greater area than the first surface after it passes through the standleg. A second filter media bed may be formed above the first filter media bed. The gas is fed tangentially into the module above the first surface. The flyash is captured on the first frusto-conical surface and within the bed mass. The processed gas flows out through the second frusto-conical surface and then through the second filter bed, if present. The bed media is cleaned of the captured flyash and recirculated to the moving granular bed filter. Alternatively, the bed media may be composed of the ash from the combustion which is pelletized to form agglomerates. The ash flows through the bed only once; it is not recycled.

Variability of Bed Load Transport During Six Summers of Continuous Measurements in Two Austrian Mountain Streams (Fischbach and Ruetz)

NASA Astrophysics Data System (ADS)

Rickenmann, Dieter

2018-01-01

Previous measurements of bed load transport in gravel bed streams revealed a large temporal and spatial variability of bed load transport rates. Using an impact plate geophone system, continuous bed load transport measurements were made during 6 years in two mountain streams in Austria. The two streams have a snow-melt and glacier-melt dominated hydrologic regime resulting in frequent transport activity during the summer half year. Periods of days to weeks were identified which are associated with approximately constant Shields values that indicate quasi-stable bed conditions. Between these stable periods, the position of the bed load transport function varied while its steepness remained approximately constant. For integration time scales of several hours to 1 day, the fluctuations in bed load transport decreased and the correlation between bed load transport and water discharge increased. For integration times of about 70-100 days, bed load transport is determined by discharge or shear stress to within a factor of about 2, relative to the 6 year mean level. Bed load texture increased with increasing mean flow strength and mean transport intensity. Weak and predominantly clockwise daily hysteresis of bed load transport was found for the first half of the summer period.

[Fire behavior of Mongolian oak leaves fuel-bed under no-wind and zero-slope conditions. I. Factors affecting fire spread rate and modeling].

PubMed

Jin, Sen; Liu, Bo-Fei; Di, Xue-Ying; Chu, Teng-Fei; Zhang, Ji-Li

2012-01-01

Aimed to understand the fire behavior of Mongolian oak leaves fuel-bed under field condition, the leaves of a secondary Mongolian oak forest in Northeast Forestry University experimental forest farm were collected and brought into laboratory to construct fuel-beds with varied loading, height, and moisture content, and a total of 100 experimental fires were burned under no-wind and zero-slope conditions. It was observed that the fire spread rate of the fuel-beds was less than 0.5 m x min(-1). Fuel-bed loading, height, and moisture contents all had significant effects on the fire spread rate. The effect of fuel-bed moisture content on the fire spread had no significant correlations with fuel-bed loading and height, but the effect of fuel-bed height was related to the fuel-bed loading. The packing ratio of fuel-beds had less effect on the fire spread rate. Taking the fuel-bed loading, height, and moisture content as predictive variables, a prediction model for the fire spread rate of Mongolian oak leaves fuel-bed was established, which could explain 83% of the variance of the fire spread rate, with a mean absolute error 0.04 m x min(-1) and a mean relative error less than 17%.

Trends in infant bedding use: National Infant Sleep Position study, 1993-2010.

PubMed

Shapiro-Mendoza, Carrie K; Colson, Eve R; Willinger, Marian; Rybin, Denis V; Camperlengo, Lena; Corwin, Michael J

2015-01-01

Use of potentially hazardous bedding, as defined by the American Academy of Pediatrics (eg, pillows, quilts, comforters, loose bedding), is a modifiable risk factor for sudden infant death syndrome and unintentional sleep-related suffocation. The proportion of US infants sleeping with these types of bedding is unknown. To investigate the US prevalence of and trends in bedding use, we analyzed 1993-2010 data from the National Infant Sleep Position study. Infants reported as being usually placed to sleep with blankets, quilts, pillows, and other similar materials under or covering them in the last 2 weeks were classified as bedding users. Logistic regression was used to describe characteristics associated with bedding use. From 1993 to 2010, bedding use declined but remained a widespread practice (moving average of 85.9% in 1993-1995 to 54.7% in 2008-2010). Prevalence was highest for infants of teen-aged mothers (83.5%) and lowest for infants born at term (55.6%). Bedding use was also frequently reported among infants sleeping in adult beds, on their sides, and on a shared surface. The rate of decline in bedding use was markedly less from 2001-2010 compared with 1993-2000. For 2007 to 2010, the strongest predictors (adjusted odds ratio: ≥1.5) of bedding use were young maternal age, non-white race and ethnicity, and not being college educated. Bedding use for infant sleep remains common despite recommendations against this practice. Understanding trends in bedding use is important for tailoring safe sleep interventions. Copyright © 2015 by the American Academy of Pediatrics.

The bedding of laboratory animals as a source of airborne contaminants.

PubMed

Kaliste, E; Linnainmaa, M; Meklin, T; Torvinen, E; Nevalainen, A

2004-01-01

In work environments with laboratory animals, the bedding of animals binds the excreta as well as other compounds originating from the animals and their environment. These may be generated into the ambient air when the personnel handle bedding in different procedures. This study compares the dustiness of different types of six clean and four soiled beddings from rat or mouse cages. The dust generation of clean bedding varied from <1 to 25 mg/m(3). When used in the cages of rats or mice for 4 days, the dust concentration of the beddings decreased, increased or stayed the same, depending on the type of bedding and animal species. A decrease in dustiness was, however, more common. The levels in the soiled beddings varied from <1 to 8.6 mg/m(3). In the case of the aspen chip bedding, the contents of bedding used in mouse, rat or rabbit cages were analysed for mesophilic bacteria and fungi, mycobacteria and endotoxins. All of these contaminants were variably found in the bedding samples, the maximal concentrations for bacteria were >6 500 000 colony-forming units (cfu)/g, for fungi 212 000 cfu/g, and for endotoxins 6500 ng/g (81 000 EU/g). The results showed that the bedding of laboratory animals may contain biologically effective compounds, and that these may be distributed into the ambient air depending on the characteristics of the bedding material. The dustiness of different bedding types is an important factor affecting the amount and quality of the occupational exposure of the personnel to airborne contaminants.

Trends in Infant Bedding Use: National Infant Sleep Position Study, 1993–2010

PubMed Central

Colson, Eve R.; Willinger, Marian; Rybin, Denis V.; Camperlengo, Lena; Corwin, Michael J.

2015-01-01

BACKGROUND: Use of potentially hazardous bedding, as defined by the American Academy of Pediatrics (eg, pillows, quilts, comforters, loose bedding), is a modifiable risk factor for sudden infant death syndrome and unintentional sleep-related suffocation. The proportion of US infants sleeping with these types of bedding is unknown. METHODS: To investigate the US prevalence of and trends in bedding use, we analyzed 1993–2010 data from the National Infant Sleep Position study. Infants reported as being usually placed to sleep with blankets, quilts, pillows, and other similar materials under or covering them in the last 2 weeks were classified as bedding users. Logistic regression was used to describe characteristics associated with bedding use. RESULTS: From 1993 to 2010, bedding use declined but remained a widespread practice (moving average of 85.9% in 1993–1995 to 54.7% in 2008–2010). Prevalence was highest for infants of teen-aged mothers (83.5%) and lowest for infants born at term (55.6%). Bedding use was also frequently reported among infants sleeping in adult beds, on their sides, and on a shared surface. The rate of decline in bedding use was markedly less from 2001–2010 compared with 1993–2000. For 2007 to 2010, the strongest predictors (adjusted odds ratio: ≥1.5) of bedding use were young maternal age, non-white race and ethnicity, and not being college educated. CONCLUSIONS: Bedding use for infant sleep remains common despite recommendations against this practice. Understanding trends in bedding use is important for tailoring safe sleep interventions. PMID:25452654

Unusual seismogenic soft-sediment deformation structures in Cambrian epicratonic carbonate deposits, western Colorado, U.S.A

NASA Astrophysics Data System (ADS)

Myrow, P.; Chen, J.

2013-12-01

A wide variety of unusual penecontemporaneous deformation structures exist in grainstone and flat-pebble conglomerate beds of the Upper Cambrian strata, western Colorado, including slide scarps, thrusted beds, irregular blocks and internally deformed beds. Slide scarps are characterized by concave-up, sharp surfaces that truncate one or more underlying beds. Thrusted beds record movement of a part of a bed onto itself along a moderate to steeply inclined (generally 25°-40°) ramp. The hanging wall lenses in cases show fault-bend geometries, with either intact or mildly deformed bedding. Irregular bedded to internally deformed blocks isolated on generally flat upper bedding surfaces are similar in composition to the underlying beds. These features represent parts of beds that were detached, moved up onto, and some distances across, the laterally adjacent undisturbed bed surfaces. The blocks moved either at the sediment-water interface or intrastratally at shallow depths within overlying muddy deposits. Finally, internally deformed beds have large blocks, fitted fabrics of highly irregular fragments, and contorted lamination, which represent heterogeneous deformation, such as brecciation and liquefaction. The various deformation structures were most probably triggered by earthquakes, considering the nature of deformation (regional distribution of liquefaction structures, and the brittle segmentation and subsequent transportation of semi-consolidated beds) and the reactivation of Mesoproterozoic, crustal-scale shear zones in the central Rockies during the Late Cambrian. Features produced by initial brittle deformation are unusual relative to most reported seismites, and may represent poorly recognized to unrecognized seismogenic structures in the rock record.

Mark-Release-Recapture Reveals Extensive Movement of Bed Bugs (Cimex lectularius L.) within and between Apartments

PubMed Central

Cooper, Richard; Wang, Changlu; Singh, Narinderpal

2015-01-01

Understanding movement and dispersal of the common bed bug (Cimex lectularius L.) under field conditions is important in the control of infestations and for managing the spread of bed bugs to new locations. We investigated bed bug movement within and between apartments using mark-release-recapture (m-r-r) technique combined with apartment-wide monitoring using pitfall-style interceptors. Bed bugs were collected, marked, and released in six apartments. The distribution of marked and unmarked bed bugs in these apartments and their 24 neighboring units were monitored over 32 days. Extensive movement of marked bed bugs within and between apartments occurred regardless of the number of bed bugs released or presence/absence of a host. Comparison of marked and unmarked bed bug distributions confirms that the extensive bed bug activity observed was not an artifact of the m-r-r technique used. Marked bed bugs were recovered in apartments neighboring five of six m-r-r apartments. Their dispersal rates at 14 or 15 d were 0.0–5.0%. The estimated number of bed bugs per apartment in the six m-r-r apartments was 2,433–14,291 at 4–7 d after release. Longevity of bed bugs in the absence of a host was recorded in a vacant apartment. Marked large nymphs (3rd– 5th instar), adult females, and adult males continued to be recovered up to 57, 113, and 134 d after host absence, respectively. Among the naturally existing unmarked bed bugs, unfed small nymphs (1st– 2nd instar) were recovered up to 134 d; large nymphs and adults were still found at 155 d when the study ended. Our findings provide important insight into the behavioral ecology of bed bugs in infested apartments and have significant implications in regards to eradication programs and managing the spread of bed bugs within multi-occupancy dwellings. PMID:26352145

Hospital-level changes in adult ICU bed supply in the United States

PubMed Central

Wallace, David J.; Seymour, Christopher W.; Kahn, Jeremy M.

2017-01-01

Objective Although the number of intensive care beds in the United States is increasing, little is known about the hospitals responsible for this growth. We sought to better characterize national growth in intensive care beds by identifying hospital-level factors associated with increasing numbers of intensive care beds over time. Design We performed a repeated-measures time series analysis of hospital-level intensive care bed supply using data from Centers for Medicare and Medicaid Services. Setting All United States acute care hospitals with adult intensive care beds over the years 1996 to 2011. Measurements & Main Results We described the number of beds, teaching status, ownership, intensive care occupancy and urbanicity for each hospital in each year of the study. We then examined the relationship between increasing intensive care beds and these characteristics, controlling for other factors. The study included 4,457 hospitals and 55,865 hospital-years. Overall, the majority of intensive care bed growth occurred in teaching hospitals (net +13,471 beds, 72.1% of total growth), hospitals with 250 or more beds (net +18,327 beds, 91.8% of total growth) and hospitals in the highest quartile of occupancy (net +10,157 beds, 54.0% of total growth). In a longitudinal multivariable model, larger hospital size, teaching status, and high intensive care occupancy were associated with subsequent-year growth. Furthermore, the effects of hospital size and teaching status were modified by occupancy: the greatest odds of increasing intensive care unit beds were in hospitals with 500 or more beds in the highest quartile of occupancy (adjusted OR: 18.9; 95% CI: 14.0 – 25.5; p<0.01) and large teaching hospitals in the highest quartile of occupancy (adjusted OR: 7.3; 95% CI: 5.3 – 9.9; p<0.01). Conclusions Increasingly, intensive care bed expansion in the United States is occurring in larger hospitals and teaching centers, particularly following a year with high intensive care unit occupancy. PMID:27661861

Legionella prevalence and risk of legionellosis in Japanese households.

PubMed

Kuroki, T; Watanabe, Y; Teranishi, H; Izumiyama, S; Amemura-Maekawa, J; Kura, F

2017-05-01

This study determined the occurrence of legionellae in private houses for which there were no available data on aquatic environments other than the water supply system. From June 2013 to November 2014, we collected 138 water and 90 swab samples from aquatic environments in 19 houses. Legionella DNA was detected via a loop-mediated isothermal amplification assay in 66 (47·8%) water and 17 (18·9%) swab samples. High Legionella DNA detection rates were observed in water samples from washing machines and aquariums. Legionella spp. was isolated from 9 (6·5%) water and 3 (3·3%) swab samples. Legionella pneumophila SG 1 was detected from the outlet water of a bathtub spout and a bath sponge. Use of amoebic co-culture effectively increased legionellae and Legionella DNA detection rates from all sample types. A logistic regression analysis revealed that the heterotrophic plate count was significantly related to Legionella contamination. Our findings indicate that there is a risk of legionellosis from exposure to Legionella spp. in a variety of aquatic environments in residential houses. Control measures for legionellae in houses should include frequent cleaning and disinfecting to reduce heterotrophic bacteria in water and, where possible, preventing aerosolization from aquatic environments.

Children's recognition of dangerous household products: child development and poisoning risk.

PubMed

Schwebel, David C; Wells, Hayley; Johnston, Anna

2015-03-01

Preliterate children may be poisoned because they fail to distinguish safe versus hazardous household products. Study 1: A total of 228 children aged 18-54 months completed four tasks assessing ability to recognize product safety. Study 2: A total of 68 children aged 17-31 months chose products to drink from pairs of dangerous versus beverage bottles. Study 3: A total of 119 children aged 18-42 months sorted 12 objects into toys, things you can drink, and things that are bad/dangerous. Left alone, children frequently touched dangerous household products. Children frequently misidentified poisonous products as safe. Some developmental trends emerged. The following packaging features apparently helped children recognize danger: black bottle color; opaque packaging; salient symbols like insects; lack of pointy spouts; squared, not round, bottles; and metal, not plastic, containers. Developing cognition helps preliterate children distinguish safe from dangerous household products. Multiple aspects of product packaging may reduce child poisoning risk if implemented by industry or policy. © The Author 2014. Published by Oxford University Press on behalf of the Society of Pediatric Psychology. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Voltage-sensitive dye imaging of mouse neocortex during a whisker detection task

PubMed Central

Kyriakatos, Alexandros; Sadashivaiah, Vijay; Zhang, Yifei; Motta, Alessandro; Auffret, Matthieu; Petersen, Carl C. H.

2016-01-01

Abstract. Sensorimotor processing occurs in a highly distributed manner in the mammalian neocortex. The spatiotemporal dynamics of electrical activity in the dorsal mouse neocortex can be imaged using voltage-sensitive dyes (VSDs) with near-millisecond temporal resolution and ∼100-μm spatial resolution. Here, we trained mice to lick a water reward spout after a 1-ms deflection of the C2 whisker, and we imaged cortical dynamics during task execution with VSD RH1691. Responses to whisker deflection were highly dynamic and spatially highly distributed, exhibiting high variability from trial to trial in amplitude and spatiotemporal dynamics. We differentiated trials based on licking and whisking behavior. Hit trials, in which the mouse licked after the whisker stimulus, were accompanied by overall greater depolarization compared to miss trials, with the strongest hit versus miss differences being found in frontal cortex. Prestimulus whisking decreased behavioral performance by increasing the fraction of miss trials, and these miss trials had attenuated cortical sensorimotor responses. Our data suggest that the spatiotemporal dynamics of depolarization in mouse sensorimotor cortex evoked by a single brief whisker deflection are subject to important behavioral modulation during the execution of a simple, learned, goal-directed sensorimotor transformation. PMID:27921068

Method for preparing a sodium/sulfur cell

DOEpatents

Weiner, Steven A.

1978-01-01

A method for preparing a sodium/sulfur cell comprising (A) inserting a solid sodium slug, adapted to be connected to an external circuit, into the anodic reaction zone of a cell subassembly maintained within an inert atmosphere, said cell subassembly comprising a cell container and a tubular cation-permeable barrier disposed within said container such that a first reaction zone is located within cation-permeable barrier and a second reaction zone is located between the outer surface of said cation-permeable barrier and the inner surface of said container, one of said reaction zones being said anodic reaction zone and the other of said reaction zone being a cathodic reaction zone containing a precast composite cathodic reactant comprising a sulfur impregnated porous conductive material connected to said cation permeable barrier and adapted to be connected to said external circuit; and (B) providing closure means for said subassembly and sealing the same to said subassembly at a temperature less than about 100.degree. C. The method of the invention overcomes deficiencies of the prior art methods by allowing preparation of a sodium/sulfur cell without the use of molten reactants and the fill spouts which are required when the cell is filled with molten reactants.

Immunolocalisation of two tropinone reductases in potato (Solanum tuberosum L.) root, stolon, and tuber sprouts.

PubMed

Kaiser, Heike; Richter, Ute; Keiner, Ronald; Brabant, Anja; Hause, Bettina; Dräger, Birgit

2006-12-01

Tropinone reductases (TRs) are essential enzymes in the tropane alkaloid biosynthesis, providing either tropine for hyoscyamine and scopolamine formation or providing pseudotropine for calystegines. Two cDNAs coding for TRs were isolated from potato (Solanum tuberosum L.) tuber sprouts and expressed in E. coli. One reductase formed pseudotropine, the other formed tropine and showed kinetic properties typical for tropine-forming tropinone reductases (TRI) involved in hyoscyamine formation. Hyoscyamine and tropine are not found in S. tuberosum plants. Potatoes contain calystegines as the only products of the tropane alkaloid pathway. Polyclonal antibodies raised against both enzymes were purified to exclude cross reactions and were used for Western-blot analysis and immunolocalisation. The TRI (EC 1.1.1.206) was detected in protein extracts of tuber tissues, but mostly in levels too low to be localised in individual cells. The function of this enzyme in potato that does not form hyoscyamine is not clear. The pseudotropine-forming tropinone reductase (EC 1.1.1.236) was detected in potato roots, stolons, and tuber sprouts. Cortex cells of root and stolon contained the protein; additional strong immuno-labelling was located in phloem parenchyma. In tuber spouts, however, the protein was detected in companion cells.

75 FR 24572 - Foreign-Trade Zone 29 - Louisville, Kentucky, Application for Subzone, Louisville Bedding Company...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-05

... - Louisville, Kentucky, Application for Subzone, Louisville Bedding Company (Household Bedding Products...-purpose subzone status for the bedding products manufacturing facilities of Louisville Bedding Company..., Louisville; Site 2 - warehouse (4.3 acres) located at 100 Quality Street, Munfordville; and, Site 3...

75 FR 28554 - Foreign-Trade Zone 50 Long Beach, California, Application for Subzone, Louisville Bedding Company...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-21

..., California, Application for Subzone, Louisville Bedding Company (Household Bedding Products), Ontario... Avenue in Ontario, California. The facility is used to manufacture household bedding products, including... shipments for the domestic market, the finished household bedding products would be entered for consumption...

21 CFR 892.1350 - Nuclear scanning bed.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Nuclear scanning bed. 892.1350 Section 892.1350...) MEDICAL DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.1350 Nuclear scanning bed. (a) Identification. A nuclear scanning bed is an adjustable bed intended to support a patient during a nuclear medicine...

21 CFR 892.1350 - Nuclear scanning bed.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Nuclear scanning bed. 892.1350 Section 892.1350...) MEDICAL DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.1350 Nuclear scanning bed. (a) Identification. A nuclear scanning bed is an adjustable bed intended to support a patient during a nuclear medicine...

21 CFR 892.1350 - Nuclear scanning bed.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Nuclear scanning bed. 892.1350 Section 892.1350...) MEDICAL DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.1350 Nuclear scanning bed. (a) Identification. A nuclear scanning bed is an adjustable bed intended to support a patient during a nuclear medicine...

21 CFR 892.1350 - Nuclear scanning bed.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Nuclear scanning bed. 892.1350 Section 892.1350...) MEDICAL DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.1350 Nuclear scanning bed. (a) Identification. A nuclear scanning bed is an adjustable bed intended to support a patient during a nuclear medicine...

21 CFR 892.1350 - Nuclear scanning bed.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Nuclear scanning bed. 892.1350 Section 892.1350...) MEDICAL DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.1350 Nuclear scanning bed. (a) Identification. A nuclear scanning bed is an adjustable bed intended to support a patient during a nuclear medicine...

3-D capacitance density imaging of fluidized bed

DOEpatents

Fasching, George E.

1990-01-01

A three-dimensional capacitance density imaging of a gasified bed or the like in a containment vessel is achieved using a plurality of electrodes provided circumferentially about the bed in levels and along the bed in channels. The electrodes are individually and selectively excited electrically at each level to produce a plurality of current flux field patterns generated in the bed at each level. The current flux field patterns are suitably sensed and a density pattern of the bed at each level determined. By combining the determined density patterns at each level, a three-dimensional density image of the bed is achieved.

Correlation of Paleocene Harmon and Hansen lignite beds, Adams, Billings, Bowman, Golden Valley, Hettinger, and Slope Counties, Williston Basin, North Dakota

DOE Office of Scientific and Technical Information (OSTI.GOV)

Keighin, C.W.; Flores, R.M.; Ochs, A.

In southwestern North Dakota, minable lignite beds in the Paleocene Fort Union Formation include the Harmon and Hansen beds in the Bowman-Gascoyne area. Data from more than 700 drill holes penetrating these beds was used to construct stratigraphic cross sections. The Harmon and Hansen beds are the thickest and most laterally persistent lignites found under < 150 ft of overburden. The Harmon coal bed is as much as 34 ft thick, and is often split by claystone interbeds of variable thickness. The Hansen coal bed typically occurs 10--100 ft below the Harmon coal bed; it rarely attains a thickness ofmore » 15 ft, and averages 4 ft in thickness.« less

Effect of bed characters on the direct synthesis of dimethyldichlorosilane in fluidized bed reactor.

PubMed

Zhang, Pan; Duan, Ji H; Chen, Guang H; Wang, Wei W

2015-03-06

This paper presents the numerical investigation of the effects of the general bed characteristics such as superficial gas velocities, bed temperature, bed heights and particle size, on the direct synthesis in a 3D fluidized bed reactor. A 3D model for the gas flow, heat transfer, and mass transfer was coupled to the direct synthesis reaction mechanism verified in the literature. The model was verified by comparing the simulated reaction rate and dimethyldichlorosilane (M2) selectivity with the experimental data in the open literature and real production data. Computed results indicate that superficial gas velocities, bed temperature, bed heights, and particle size have vital effect on the reaction rates and/or M2 selectivity.

Effect of Bed Characters on the Direct Synthesis of Dimethyldichlorosilane in Fluidized Bed Reactor

PubMed Central

Zhang, Pan; Duan, Ji H.; Chen, Guang H.; Wang, Wei W.

2015-01-01

This paper presents the numerical investigation of the effects of the general bed characteristics such as superficial gas velocities, bed temperature, bed heights and particle size, on the direct synthesis in a 3D fluidized bed reactor. A 3D model for the gas flow, heat transfer, and mass transfer was coupled to the direct synthesis reaction mechanism verified in the literature. The model was verified by comparing the simulated reaction rate and dimethyldichlorosilane (M2) selectivity with the experimental data in the open literature and real production data. Computed results indicate that superficial gas velocities, bed temperature, bed heights, and particle size have vital effect on the reaction rates and/or M2 selectivity. PMID:25742729

Bed Bugs (Cimex lectularius) as Vectors of Trypanosoma cruzi

PubMed Central

Salazar, Renzo; Castillo-Neyra, Ricardo; Tustin, Aaron W.; Borrini-Mayorí, Katty; Náquira, César; Levy, Michael Z.

2015-01-01

Populations of the common bed bug, Cimex lectularius, have recently undergone explosive growth. Bed bugs share many important traits with triatomine insects, but it remains unclear whether these similarities include the ability to transmit Trypanosoma cruzi, the etiologic agent of Chagas disease. Here, we show efficient and bidirectional transmission of T. cruzi between hosts and bed bugs in a laboratory environment. Most bed bugs that fed on experimentally infected mice acquired the parasite. A majority of previously uninfected mice became infected after a period of cohabitation with exposed bed bugs. T. cruzi was also transmitted to mice after the feces of infected bed bugs were applied directly to broken host skin. Quantitative bed bug defecation measures were similar to those of important triatomine vectors. Our findings suggest that the common bed bug may be a competent vector of T. cruzi and could pose a risk for vector-borne transmission of Chagas disease. PMID:25404068

Bed bugs, public health, and social justice: Part 2, An opinion survey.

PubMed

Eddy, Christopher; Jones, Susan C

2011-04-01

Bed bug infestations have resurged globally, nationally, and locally, yet the public health community in the U.S. has yet to mount a coordinated response to the escalating bed bug problem. Surveys of attendees at the 2009 National Environmental Health Association Annual Educational Conference & Exhibition, 2009 Ohio Association of Health Commissioners Fall Conference, 2009 Central Ohio Bed Bug Summit, and 2010 Hamilton County Council on Aging Annual Conference were conducted to gauge opinions about bed bugs. Survey results revealed that 90% of all respondents considered bed bugs to be a public health concern, and 73% indicated that bed bugs pose an environmental justice concern. These findings, which indicate that bed bugs are an inescapable public health mandate with environmental justice undertones, should rally public health agencies at federal, state, and local levels to respond with authority of agency to the escalating bed bug problem.

Relationship between fluid bed aerosol generator operation and the aerosol produced

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carpenter, R.L.; Yerkes, K.

1980-12-01

The relationships between bed operation in a fluid bed aerosol generator and aerosol output were studied. A two-inch diameter fluid bed aerosol generator (FBG) was constructed using stainless steel powder as a fluidizing medium. Fly ash from coal combustion was aerosolized and the influence of FBG operating parameters on aerosol mass median aerodynamic diameter (MMAD), geometric standard deviation (sigma/sub g/) and concentration was examined. In an effort to extend observations on large fluid beds to small beds using fine bed particles, minimum fluidizing velocities and elutriation constant were computed. Although FBG minimum fluidizing velocity agreed well with calculations, FBG elutriationmore » constant did not. The results of this study show that the properties of aerosols produced by a FBG depend on fluid bed height and air flow through the bed after the minimum fluidizing velocity is exceeded.« less

Differences in sleep complaints in adults with varying levels of bed days residing in extended care facilities for chronic disease management.

PubMed

Fox, Mary T; Sidani, Souraya; Brooks, Dina

2010-05-01

This cohort study examined differences in perceived insomnia and daytime sleepiness in 67 adults residing in extended care facilities for chronic disease management who had varying levels of bed days. One bed day was defined as spending 24 hours in bed. Planned pairwise comparisons, using Bonferroni adjustment, were made between participants who spent 0 (n = 21), 2 to 4 (n = 23), and 5 to 7 (n = 23) days in bed during 1 week of monitoring. Participants who spent 5 to 7 days in bed had significantly greater insomnia than those who spent 2 to 4 days in bed. No group differences were found in daytime sleepiness. Based on the findings, nurses may assess subjective insomnia and explore sleep hygiene strategies, such as increasing time out of bed with patients who have high levels of 5 to 7 bed days.

Ethnic differences in prevalence and determinants of mother-child bed-sharing in early childhood.

PubMed

Luijk, Maartje P C M; Mileva-Seitz, Viara R; Jansen, Pauline W; van IJzendoorn, Marinus H; Jaddoe, Vincent W V; Raat, Hein; Hofman, Albert; Verhulst, Frank C; Tiemeier, Henning

2013-11-01

To date few studies have examined how multiple layers of influences shape the emergence of bed-sharing practices in the first 2 years postpartum. In our report, we examined bed-sharing in a large multiethnic sample, exploring the influences of three broad classes of influence on bed-sharing at single time points and across time: (1) sociodemographic and (2) contextual factors such as breastfeeding, maternal mental health and stress, and (3) child temperament and sleep habits. Frequencies of bed-sharing were assessed at two time points, 2 and 24 months, in a population-based multiethnic (Dutch, Turkish or Moroccan, and Caribbean) sample of 6309 children born in the Netherlands. In Dutch mothers, the majority of mothers did not share their beds with their child, and bed-sharing rates decreased from 2 to 24 months. Other ethnic groups showed higher bed-sharing rates, typified by both increases in bed-sharing (the Turkish and Moroccan group) and persistence of bed-sharing over time (the Caribbean group). There were few family and child characteristics associated with bed-sharing in the non-Dutch ethnic groups. In contrast, bed-sharing in Dutch mothers was associated with child temperament and sleeping problems, maternal depression, and sociodemographic variables like crowding and maternal education. Our results suggest that mothers with a Turkish and Moroccan or Caribbean background were more influenced by cultural values, whereas bed-sharing practices were more reactive in the Dutch group. Copyright © 2013 Elsevier B.V. All rights reserved.

Clinical phenotype of bipolar disorder with comorbid binge eating disorder

PubMed Central

McElroy, Susan L.; Crow, Scott; Biernacka, Joanna M.; Winham, Stacey; Geske, Jennifer; Cuellar Barboza, Alfredo B.; Prieto, Miguel L.; Chauhan, Mohit; Seymour, Lisa R.; Mori, Nicole; Frye, Mark A.

2017-01-01

Background To explore the relationship between binge eating disorder (BED) and obesity in patients with bipolar disorder (BP). Methods 717 patients participating in the Mayo Clinic Bipolar Biobank completed structured diagnostic interviews and questionnaires for demographic and illness-related variables. They also had weight and height measured to determine body mass index (BMI). The effects of BED and obesity (BMI≥30 kg/m2), as well as their interaction, were assessed on one measure of general medical burden and six proxies of psychiatric illness burden. Results 9.5% of patients received a clinical diagnosis of BED and 42.8% were obese. BED was associated with a significantly elevated BMI. Both BED and obesity were associated with greater psychiatric and general illness burden, but illness burden profiles differed. After controlling for obesity, BED was associated with suicidality, psychosis, mood instability, anxiety disorder comorbidity, and substance abuse comorbidity. After controlling for BED status, obesity was associated with greater general medical comorbidity, but lower substance abuse comorbidity. There were no significant interaction effects between obesity and BED, or BMI and BED, on any illness burden outcome. Limitations There may have been insufficient power to detect interactions between BED and obesity. Conclusions: Among patients with BP, BED and obesity are highly prevalent and correlated, but associated with different profiles of enhanced illness burden. As the association of BED with greater psychiatric illness burden remained significant even after accounting for the effect of obesity, BP with BED may represent a clinically important sub-phenotype. PMID:23742827

Debris-bed friction of hard-bedded glaciers

USGS Publications Warehouse

Cohen, D.; Iverson, N.R.; Hooyer, T.S.; Fischer, U.H.; Jackson, M.; Moore, P.L.

2005-01-01

[1] Field measurements of debris-bed friction on a smooth rock tablet at the bed of Engabreen, a hard-bedded, temperate glacier in northern Norway, indicated that basal ice containing 10% debris by volume exerted local shear traction of up to 500 kPa. The corresponding bulk friction coefficient between the dirty basal ice and the tablet was between 0.05 and 0.08. A model of friction in which nonrotating spherical rock particles are held in frictional contact with the bed by bed-normal ice flow can account for these measurements if the power law exponent for ice flowing past large clasts is 1. A small exponent (n < 2) is likely because stresses in ice are small and flow is transient. Numerical calculations of the bed-normal drag force on a sphere in contact with a flat bed using n = 1 show that this force can reach values several hundred times that on a sphere isolated from the bed, thus drastically increasing frictional resistance. Various estimates of basal friction are obtained from this model. For example, the shear traction at the bed of a glacier sliding at 20 m a-1 with a geothermally induced melt rate of 0.006 m a-1 and an effective pressure of 300 kPa can exceed 100 kPa. Debris-bed friction can therefore be a major component of sliding resistance, contradicting the common assumption that debris-bed friction is negligible. Copyright 2005 by the American Geophysical Union.

Relationship Between Faults Oriented Parallel and Oblique to Bedding in Neogene Massive Siliceous Mudstones at The Horonobe Underground Research Laboratory, Japan

NASA Astrophysics Data System (ADS)

Hayano, Akira; Ishii, Eiichi

2016-10-01

This study investigates the mechanical relationship between bedding-parallel and bedding-oblique faults in a Neogene massive siliceous mudstone at the site of the Horonobe Underground Research Laboratory (URL) in Hokkaido, Japan, on the basis of observations of drill-core recovered from pilot boreholes and fracture mapping on shaft and gallery walls. Four bedding-parallel faults with visible fault gouge, named respectively the MM Fault, the Last MM Fault, the S1 Fault, and the S2 Fault (stratigraphically, from the highest to the lowest), were observed in two pilot boreholes (PB-V01 and SAB-1). The distribution of the bedding-parallel faults at 350 m depth in the Horonobe URL indicates that these faults are spread over at least several tens of meters in parallel along a bedding plane. The observation that the bedding-oblique fault displaces the Last MM fault is consistent with the previous interpretation that the bedding- oblique faults formed after the bedding-parallel faults. In addition, the bedding-parallel faults terminate near the MM and S1 faults, indicating that the bedding-parallel faults with visible fault gouge act to terminate the propagation of younger bedding-oblique faults. In particular, the MM and S1 faults, which have a relatively thick fault gouge, appear to have had a stronger control on the propagation of bedding-oblique faults than did the Last MM fault, which has a relatively thin fault gouge.

Reported bed net ownership and use in social contacts is associated with uptake of bed nets for malaria prevention in pregnant women in Ghana.

PubMed

Ernst, Kacey C; Erly, Steven; Adusei, Charity; Bell, Melanie L; Kessie, David Komla; Biritwum-Nyarko, Alberta; Ehiri, John

2017-01-04

Despite progress made in the last decades, malaria persists as a pressing health issue in sub-Saharan Africa. Pregnant women are particularly vulnerable to infection and serious health outcomes for themselves and their unborn child. Risk can be mitigated through appropriate use of control measures such as insecticide-treated bed nets. Although social networks can influence uptake of preventive strategies, the role of social influence on bed net ownership has not been explored. During an evaluation of a bed net distribution programme, the influence of non-health care advisors on ownership and use of bed nets by pregnant women in Kumasi, Ghana was examined. Data were collected through in-person interviews with 300 pregnant women seeking antenatal care in an urban hospital in Kumasi, Ghana. Participants were asked about their bed net ownership, bed net use, and information about three personal contacts that they go to for pregnancy advice. Information about these advisors was combined into an influence score. Logistic regression models were used to determine the association between the score and bed net ownership. Those who owned a bed net were further assessed to determine if interpersonal influence was associated with self-reported sleeping under the bed net the previous night. Of the 294 women in the analysis, 229 (78%) reported owning bed nets. Of these bed net owners, 139 (61%) reported using a bed net the previous night. A dose response relationship was observed between the interpersonal influence score and bed net ownership and use. Compared to the lowest influence score, those with the highest influence score (>1 SD above the mean) were marginally more likely to own a bed net [OR = 2.37, 95% CI (0.87, 6.39)] and much more likely to use their bed net [5.38, 95% CI (1.89, 15.25)] after adjusting for other factors. Interpersonal influence appears to have modest impact on ownership and use of bed nets by pregnant women in an urban area of Ghana. Further investigations would need to be conducted to determine if the relationship is causal or if individuals who associate are simply more likely to have similar practices.

Infant's bed climate and bedding in the Japanese home.

PubMed

Nakamura Ikeda, Rie; Fukai, Kiyoko; Okamoto Mizuno, Kazue

2012-06-01

to assess the bed climate of infants in their homes in Japan. descriptive, exploratory, non-experimental research design. the data were collected at the participants' homes under normal circumstances. nineteen healthy infants between the ages of two and five months. Their mothers, who joined a parenting class organised by a maternity clinic in Okayama, Japan, consented to participate in this study. we visited the infants' homes and interviewed their mothers concerning the types and use of bedding. The temperature and relative humidity of the bed climate at the back and foot of the bedding, and in the room were measured every minute for four consecutive days. Differences among the bed climates measured during three seasons (spring, summer, and autumn) were assessed by one-way analysis of variance. The bed temperature was higher for infants than for adults. No significant difference in temperature was noted among the three seasons. The bed temperature was about 36.0°C when waterproof sheets and futon mattresses for children or adult were used. The average relative humidity of the bed climate at the back was highest in summer, followed by that in spring and autumn; the differences were significant. The use of waterproof sheets and futon mattresses for children in summer increased the relative humidity to 80% or more. The use of infant beds, sunoko drainboards, and cotton futon mattresses in summer was effective in reducing the bed humidity. these results suggest that nurse-midwives should advise the parents on comfortable bed climates for their infants, as well as how to select and use bedding for them. Copyright © 2010 Elsevier Ltd. All rights reserved.

Repellency of selected chemicals against the bed bug (Hemiptera: Cimicidae).

PubMed

Wang, Changlu; Lü, Lihua; Zhang, Aijun; Liu, Chaofeng

2013-12-01

In recent years, the common bed bug, Cimex lectularius L. (Hemiptera: Cimicidae), became a major public health concern in urban communities. Bed bugs are notoriously difficult to control, and their bites are not tolerated by most people. The public has an urgent need for materials and methods to reduce bed bug introduction and bites during work, travel, or sleep. A repellent product will help achieve these goals by discouraging and preventing bed bugs from moving to a protected area. We evaluated the repellency of three commercially available insect repellent or control materials and five nonregistered materials with the goal of identifying safe and effective bed bug repellents. The two commercial repellent products that contained 7% picaridin or 0.5% permethrin had little repellency against bed bugs. N,N-diethyl-m-toluamide (DEET), the most commonly used insect repellent, provided a high level of repellency against bed bugs. When a host cue (carbon dioxide) was present, the minimum DEET concentration to repel > or = 94% of the bed bugs for a9-h period was 10%. The longevity of repellency of DEET was concentration dependent. At 25% concentration, DEET-treated fabric surface remained highly repellent to bed bugs for a 14-d period. However, DEET has a strong smell and dissolves certain plastic materials. Therefore, we evaluated several odorless, noncorrosive, and potentially effective repellents. Isolongifolenone and isolongifolanone, two natural products and recently reported insect repellents, exhibited strong repellent property against bed bugs but at significantly lower levels than DEET. Three novel potential repellent compounds discovered by Bedoukian Research Inc. (Danbury, CT) exhibited similar level of repellency and longevity as DEET for repelling bed bugs. These nonirritant and odorless compounds are promising candidates as alternatives to DEET for reducing the spread of bed bugs and bed bug bites.

The Effects of Long Duration Bed Rest on Functional Mobility and Balance: Relationship to Resting State Motor Cortex Connectivity

NASA Technical Reports Server (NTRS)

Erdeniz, B.; Koppelmans, V.; Bloomberg, J. J.; Kofman, I. S.; DeDios, Y. E.; Riascos-Castaneda, R. F.; Wood, S. J.; Mulavara, A. P.; Seidler, R. D.

2014-01-01

NASA offers researchers from a variety of backgrounds the opportunity to study bed rest as an experimental analog for space flight. Extended exposure to a head-down tilt position during long duration bed rest can resemble many of the effects of a low-gravity environment such as reduced sensory inputs, body unloading and increased cephalic fluid distribution. The aim of our study is to a) identify changes in brain function that occur with prolonged bed rest and characterize their recovery time course; b) assess whether and how these changes impact behavioral and neurocognitive performance. Thus far, we completed data collection from six participants that include task based and resting state fMRI. The data have been acquired through the bed rest facility located at the University of Texas Medical Branch (Galveston, TX). Subjects remained in bed with their heads tilted down 6 degrees below their feet for 70 consecutive days. Behavioral measures and neuroimaging assessments were obtained at seven time points: a) 7 and 12 days before bed rest; b) 7, 30, and 65 days during bed rest; and c) 7 and 12 days after bed rest. Functional connectivity magnetic resonance imaging (FcMRI) analysis was performed to assess the connectivity of motor cortex in and out of bed rest. We found a decrease in motor cortex connectivity with vestibular cortex and the cerebellum from pre bed rest to in bed rest. We also used a battery of behavioral measures including the functional mobility test and computerized dynamic posturography collected before and after bed rest. We will report the preliminary results of analyses relating brain and behavior changes. Furthermore, we will also report the preliminary results of a spatial working memory task and vestibular stimulation during in and out of bed rest.

Characterization of Binge-Eating Behavior in Individuals With Binge-Eating Disorder in an Adult Population in the United States.

PubMed

Pawaskar, Manjiri; Solo, Kirk; Valant, Jason; Schmitt, Emily; Nwankwo, Millicent; Herman, Barry K

2016-10-27

Characterize the frequency, duration, and severity of binge-eating behaviors in adults meeting DSM-5 criteria for binge-eating disorder (BED) in a large US community sample. A representative sample of US adults from the National Health and Wellness Survey was recruited from an online panel and asked to respond to an Internet survey (conducted in October 2013) that included questions designed to assess binge-eating behaviors in relation to DSM-5 BED diagnostic criteria. Of 22,397 respondents, 344 self-reported meeting DSM-5 BED criteria (BED respondents). Most BED respondents reported that binge-eating episodes had occurred for the past 7-12 months (61.0%), and 93.6% reported ≥ 2-3 binge-eating episodes/wk. All BED respondents reported that "extreme" (52.6%) or "great" (47.4%) distress levels were associated with binge-eating episodes. Among BED respondents who agreed to provide detailed binge-eating behavior data after being invited to respond to additional survey questions, 40.6% reported binge eating on average > 1 time/d, and 59.2% reported binge eating 2-3 times/d. For 44.5% of BED respondents, binge-eating duration was 31-60 minutes. BED respondents reported that they "very often" (36.6%) or "often" (34.0%) had urges to binge eat between 7-10 pm. "Feeling disgusted with oneself, depressed, or guilty afterward" was the most bothersome symptom of binge eating for BED respondents (extremely bothersome: 41.9%). Binge-eating frequency among BED respondents averaged once daily. Most BED respondents exhibited binge-eating behavior for 7-12 months, often with severe symptoms. These findings highlight the disease burden of BED and have potential implications for diagnosing and treating BED. © Copyright 2016 Physicians Postgraduate Press, Inc.

Ammonia, Total Reduced Sulfides, and Greenhouse Gases of Pine Chip and Corn Stover Bedding Packs.

PubMed

Spiehs, Mindy J; Brown-Brandl, Tami M; Parker, David B; Miller, Daniel N; Berry, Elaine D; Wells, James E

2016-03-01

Bedding materials may affect air quality in livestock facilities. Our objective in this study was to compare headspace concentrations of ammonia (NH), total reduced sulfides (TRS), carbon dioxide (CO), methane (CH), and nitrous oxide (NO) when pine wood chips ( spp.) and corn stover ( L.) were mixed in various ratios (0, 10, 20, 30, 40, 60, 80, and 100% pine chips) and used as bedding with manure. Air samples were collected from the headspace of laboratory-scaled bedded manure packs weekly for 42 d. Ammonia concentrations were highest for bedded packs containing 0, 10, and 20% pine chips (equivalent to 501.7, 502.3, and 502.3 mg m, respectively) in the bedding mixture and were lowest when at least 80% pine chips were used as bedding (447.3 and 431.0 mg m, respectively for 80 and 100% pine chip bedding). The highest NH concentrations were observed at Day 28. The highest concentration of TRS was observed when 100% pine chips were used as bedding (11.4 µg m), with high concentrations occurring between Days 7 and 14, and again at Day 35. Greenhouse gases were largely unaffected by bedding material but CH and CO concentrations increased as the bedded packs aged and NO concentrations were highly variable throughout the incubation. We conclude that a mixture of bedding material that contains 30 to 40% pine chips may be the ideal combination to reduce both NH and TRS emissions. All gas concentrations increased as the bedded packs aged, suggesting that frequent cleaning of facilities would improve air quality in the barn, regardless of bedding materials used. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Material exchange and food web of seagrass beds in the Sylt-Rømø Bight: how significant are community changes at the ecosystem level?

NASA Astrophysics Data System (ADS)

Asmus, H.; Asmus, R.

2000-07-01

Material exchange, biodiversity and trophic transfer within the food web were investigated in two different types of intertidal seagrass beds: a sheltered, dense Zostera marina bed and a more exposed, sparse Z. noltii bed, in the Northern Wadden Sea. Both types of Zostera beds show a seasonal development of above-ground biomass, and therefore measurements were carried out during the vegetation period in summer. The exchange of particles and nutrients between seagrass beds and the overlying water was measured directly using an in situ flume. Particle sedimentation [carbon (C), nitrogen (N) and phosphorus (P) constituents] from the water column prevailed in dense seagrass beds. In the sheltered, dense seagrass bed, a net particle uptake was found even on windy days (7-8 Beaufort). Dissolved inorganic N and orthophosphate were mainly taken up by the dense seagrass bed. At times of strong winds, nutrients were released from the benthic community to tidal waters. In a budget calculation of total N and total P, the dense seagrass beds were characterised as a material sink. The seagrass beds with sparse Z. noltii were a source of particles even during calm weather. The uptake of dissolved inorganic N in the sparse seagrass bed was low but significant, while the uptake of inorganic phosphate and silicate by seagrasses and their epiphytes was exceeded by release processes from the sediment into the overlying water. Estimates at the ecosystem level showed that material fluxes of seagrass beds in the Sylt-Rømø Bight are dominated by the dense type of Zostera beds. Therefore, seagrass beds act as a sink for particles and for dissolved inorganic nutrients. During storms, seagrass beds are distinct sources for inorganic nutrients. The total intertidal area of the Sylt-Rømø Bight could be described as a sink for particles and a source for dissolved nutrients. This balance of the material budget was estimated by either including or excluding seagrass beds. Including the subtidal part, the function of the ecosystem as a source for particles increased, supposing that all seagrass beds were lost from the area. During the vegetation period, seagrass beds act as a storage compartment for material accumulated in the living biomass of the community. There was great biodiversity among the plant and animal groups found in intertidal seagrass beds of the Sylt-Rømø Bay, representing 50-86% of the total number of species investigated, depending on the particular group. Since most species are not exclusively seagrass residents, the loss of intertidal seagrass beds would be of minor importance for biodiversity at the ecosystem level. Food web structure in seagrass beds is different from other intertidal communities. Primary production and detritus input is high, but secondary production is similar to that of unvegetated areas, although the relative importance of the trophic guilds is different. The loss of seagrass beds leads to profound alterations in the food web of the total ecosystem. Historical as well as recent changes in material fluxes and energy flow due to man-made alterations to the ecosystem are discussed.

7 CFR 2902.15 - Bedding, bed linens, and towels.

Code of Federal Regulations, 2010 CFR

2010-01-01

... PROCUREMENT Designated Items § 2902.15 Bedding, bed linens, and towels. (a) Definition. (1) Bedding is that... minimum biobased content is 12 percent and shall be based on the amount of qualifying biobased carbon in..., and silk are not qualifying biobased feedstocks for the purpose of determining the biobased content of...

Health Information in Amharic (Amarɨñña / አማርኛ )

MedlinePlus

... Section Bed Bugs Bed Bug Control in Residences - English PDF Bed Bug Control in Residences - Amarɨñña / አማርኛ ( ... Department of Agriculture Vacuuming to Capture Bed Bugs - English PDF Vacuuming to Capture Bed Bugs - Amarɨñña / አማርኛ ( ...

Thermal Analysis of Fluidized Bed and Fixed Bed Latent Heat Thermal Storage System

NASA Astrophysics Data System (ADS)

Beemkumar, N.; Karthikeyan, A.; Shiva Keshava Reddy, Kota; Rajesh, Kona; Anderson, A.

2017-05-01

Thermal energy storage technology is essential because its stores available energy at low cost. Objective of the work is to store the thermal energy in a most efficient method. This work is deal with thermal analysis of fluidized bed and fixed bed latent heat thermal storage (LHTS) system with different encapsulation materials (aluminium, brass and copper). D-Mannitol has been used as phase change material (PCM). Encapsulation material which is in orbicular shape with 4 inch diameter and 2 mm thickness orbicular shaped product is used. Therminol-66 is used as a heat transfer fluid (HTF). Arrangement of encapsulation material is done in two ways namely fluidized bed and fixed bed thermal storage system. Comparison was made between the performance of fixed bed and fluidized bed with different encapsulation material. It is observed that from the economical point of view aluminium in fluidized bed LHTS System has highest efficiency than copper and brass. The thermal energy storage system can be analyzed with fixed bed by varying mass flow rate of oil paves a way to find effective heat energy transfer.

Flow resistance and suspended load in sand-bed rivers: Simplified stratification model

USGS Publications Warehouse

Wright, S.; Parker, G.

2004-01-01

New methods are presented for the prediction of the flow depth, grain-size specific near-bed concentration, and bed-material suspended sediment transport rate in sand-bed rivers. The salient improvements delineated here all relate to the need to modify existing formulations in order to encompass the full range of sand-bed rivers, and in particular large, low-slope sand-bed rivers. They can be summarized as follows: (1) the inclusion of density stratification effects in a simplified manner, which have been shown in the companion paper to be particularly relevant for large, low-slope, sand-bed rivers; (2) a new predictor for near-bed entrainment rate into suspension which extends a previous relation to the range of large, low-slope sand-bed rivers; and (3) a new predictor for form drag which again extends a previous relation to include large, low-slope sand-bed rivers. Finally, every attempt has been made to cast the relations in the simplest form possible, including the development of software, so that practicing engineers may easily use the methods. ?? ASCE.

Survival and Transstadial Persistence of Trypanosoma cruzi in the bed bug (Hemiptera: Cimicidae).

PubMed

Blakely, Brittny N; Hanson, Stephen F; Romero, Alvaro

2018-05-04

Bed bug populations are increasing around the world at an alarming rate and have become a major public health concern. The appearance of bed bug populations in areas where Chagas disease is endemic raises questions about the role of these insects in the transmission of Trypanosoma cruzi, the etiological agent of the disease. In a series of laboratory evaluations, bed bug adults and nymphs were experimentally fed with T. cruzi-infected blood to assess the ability of T. cruzi to survive inside the bed bug and throughout the insect's molting process. Live T. cruzi were observed in gut contents of experimentally infected bed bug adults via light microscopy and the identity of the parasite was confirmed via polymerase chain reaction analysis. T. cruzi persisted at least 97-d postinfection in adult bed bugs. Nymphal stage bed bugs that were infected with T. cruzi maintained the parasite after molting, indicating that transstadial passage of T. cruzi in bed bugs took place. This report provides further evidence of acquisition, maintenance, and for the first time, transstadial persistence of T. cruzi in bed bugs.

Reducing Respiratory Health Risks to Horses and Workers: A Comparison of Two Stall Bedding Materials

PubMed Central

Saastamoinen, Markku; Särkijärvi, Susanna; Hyyppä, Seppo

2015-01-01

Simple Summary In this study, the effect of wood shavings and peat was examined on stable air quality and health of horses and stable workers. The ammonia level in the boxes in which peat was used as bedding was non-existent or very low. The respiratory symptoms in horses increased regardless of the bedding material at the beginning of the study. The health status of the horses on peat bedding returned to the initial level in the end of the trial but horses in stalls bedded with wood shavings continued to be symptomatic. The hooves of the horses in stalls with peat bedding had a better moisture content. The results suggest that peat is a better bedding material for horses and people working or visiting horse stables than wood shavings. Abstract Stable air quality and the choice of bedding material are an important health issue both in horses and people working or visiting horse stables. Risks of impaired respiratory health are those that can especially be avoided by improving air quality in the stable. The choice of bedding material is particularly important in cold climate conditions; where horses are kept most of the day and year indoors throughout their life. This study examined the effect of two bedding materials; wood shavings and peat; on stable air quality and health of horses. Ammonia and dust levels were also measured to assess conditions in the stable. Ammonia was not detected or was at very low levels (<0.25 ppm) in the boxes in which peat was used as bedding; but its concentration was clearly higher (1.5–7.0 ppm) in stalls with wood shavings as bedding. Personal measurements of workers revealed quite high ammonia exposure (5.9 ppm8h) in the boxes in which wood shavings were used; but no exposure was observed in stalls bedded with peat. The respiratory symptoms in horses increased regardless of the bedding material at the beginning of the study. The health status of the horses in the peat bedding group returned to the initial level in the end of the trial but horses bedded with wood shavings continued to be symptomatic. The hooves of the horses with peat bedding had a better moisture content than those of the horses bedded with wood shavings. The results suggest that peat is a better bedding material for horses than wood shavings regarding the health of both horses and stable workers. PMID:26479479

Bed Bug Infestations in an Urban Environment

PubMed Central

Svoboda, Tomislav J.; De Jong, Iain J.; Kabasele, Karl J.; Gogosis, Evie

2005-01-01

Until recently, bed bugs have been considered uncommon in the industrialized world. This study determined the extent of reemerging bed bug infestations in homeless shelters and other locations in Toronto, Canada. Toronto Public Health documented complaints of bed bug infestations from 46 locations in 2003, most commonly apartments (63%), shelters (15%), and rooming houses (11%). Pest control operators in Toronto (N = 34) reported treating bed bug infestations at 847 locations in 2003, most commonly single-family dwellings (70%), apartments (18%), and shelters (8%). Bed bug infestations were reported at 20 (31%) of 65 homeless shelters. At 1 affected shelter, 4% of residents reported having bed bug bites. Bed bug infestations can have an adverse effect on health and quality of life in the general population, particularly among homeless persons living in shelters. PMID:15829190

The Influence of Relative Submergence on the Near-bed Flow Field: Implications for Bed-load Transport

NASA Astrophysics Data System (ADS)

Cooper, J.; Tait, S.; Marion, A.

2005-12-01

Bed-load is governed by interdependent mechanisms, the most significant being the interaction between bed roughness, surface layer composition and near-bed flow. Despite this, practically all transport rate equations are described as a function of average bed shear stress. Some workers have examined the role of turbulence in sediment transport (Nelson et al. 1995) but have not explored the potential significance of spatial variations in the near-bed flow field. This is unfortunate considering evidence showing that transport is spatially heterogeneous and could be linked to the spatial nature of the near-bed flow (Drake et al., 1988). An understanding is needed of both the temporal and spatial variability in the near-bed flow field. This paper presents detailed spatial velocity measurements of the near-bed flow field over a gravel-bed, obtained using Particle Image Velocimetry. These data have been collected in a laboratory flume under two regimes: (i) tests with one bed slope and different flow depths; and (ii) tests with a combination of flow depths and slopes at the same average bed shear stress. Results indicate spatial variation in the streamwise velocities of up to 45 per cent from the double-averaged velocity (averaged in both time and space). Under both regimes, as the depth increased, spatial variability in the flow field increased. The probability distributions of near-bed streamwise velocities became progressively more skewed towards the higher velocities. This change was more noticeable under regime (i). This has been combined with data from earlier tests in which the near-bed velocity close to an entraining grain was measured using a PIV/image analysis system (Chegini et al, 2002). This along with data on the shape of the probability density function of velocities capable of entraining individual grains derived from a discrete-particle model (Heald et al., 2004) has been used to estimate the distribution of local velocities required for grain motion in the above tests. The overlap between this distribution and the measured velocities are used to estimate entrainment rates. Predicted entrainment rates increase with relative submergence, even for similar bed shear stress. Assuming bed-load rate is the product of entrainment rate and hop length, and that hop lengths are sensibly stable, suggests that transport rate has a dependence on relative submergence. This demonstrates that transport rate is not a direct function of average bed shear stress. The results describe a mechanism that will cause river channels with contrasting morphologies (and different relative submergence) but similar levels of average bed stress to experience different levels of sediment mobility. Chegini A. Tait S. Heald J. McEwan I. 2002 The development of an automated system for the measurement of near bed turbulence and grain motion. Proc. ASCE Conf. on Hydraulic Measurements and Experimental Methods, ISBN 0-7844-0655-3. Drake T.G. Shreve R.L. Dietrich W.E. Whiting P.J. Leopold L.B. 1988 Bedload transport of fine gravel observed by motion-picture photography, J. Fluid Mech., 192, 193-217. Heald J. McEwan I. Tait, S. 2004 Sediment transport over a flat bed in a unidirectional flow: simulations and validation, Phil. Trans. Roy. Soc. of London A, 362, 1973-1986. Nelson J.M. Shreve R.L. McLean S.R. Drake T.G. 1995 Role of near-bed turbulence structure in bed-load transport and bed form mechanics, Water. Res. Res., 31, 8, 2071-2086.

Temporal and spatial variability in thalweg profiles of a gravel-bed river

USGS Publications Warehouse

Madej, Mary Ann

1999-01-01

This study used successive longitudinal thalweg profiles in gravel-bed rivers to monitor changes in bed topography following floods and associated large sediment inputs. Variations in channel bed elevations, distributions of residual water depths, percentage of channel length occupied by riffles, and a spatial autocorrelation coefficient (Moran's I) were used to quantify changes in morphological diversity and spatial structure in Redwood Creek basin, northwestern California. Bed topography in Redwood Creek and its major tributaries consists primarily of a series of pools and riffles. The size, frequency and spatial distribution of the pools and riffles have changed significantly during the past 20 years. Following large floods and high sediment input in Redwood Creek and its tributaries in 1975, variation in channel bed elevations was low and the percentage of the channel length occupied by riffles was high. Over the next 20 years, variation in bed elevations increased while the length of channel occupied by riffles decreased. An index [(standard deviation of residual water depth/bankfull depth) × 100] was developed to compare variations in bed elevation over a range of stream sizes, with a higher index being indicative of greater morphological diversity. Spatial autocorrelation in the bed elevation data was apparent at both fine and coarse scales in many of the thalweg profiles and the observed spatial pattern of bed elevations was found to be related to the dominant channel material and the time since disturbance. River reaches in which forced pools dominated, and in which large woody debris and bed particles could not be easily mobilized, exhibited a random distribution of bed elevations. In contrast, in reaches where alternate bars dominated, and both wood and gravel were readily transported, regularly spaced bed topography developed at a spacing that increased with time since disturbance. This pattern of regularly spaced bed features was reversed following a 12-year flood when bed elevations became more randomly arranged.

Evaluation of two least toxic integrated pest management programs for managing bed bugs (Heteroptera: Cimicidae) with discussion of a bed bug intercepting device.

PubMed

Wang, Changlu; Gibb, Timothy; Bennett, Gary W

2009-05-01

The cost and effectiveness of two bed bug (Cimex lectularius L.) integrated pest management (IPM) programs were evaluated for 10 wk. Sixteen bed bug-infested apartments were chosen from a high-rise low-income apartment building. The apartments were randomly divided into two treatment groups: diatomaceous earth dust-based IPM (D-IPM) and chlorfenapyr spray-based IPM (S-IPM). The initial median (minimum, maximum) bed bug counts (by visual inspection) of the two treatment groups were 73.5 (10, 352) and 77 (18, 3025), respectively. A seminar and an educational brochure were delivered to residents and staff. It was followed by installing encasements on mattresses and box springs and applying hot steam to bed bug-infested areas in all 16 apartments. Diatomaceous earth dust (Mother Earth-D) was applied in the D-IPM group 2 d after steaming. In addition, bed bug-intercepting devices were installed under legs of infested beds or sofas or chairs to intercept bed bugs. The S-IPM group only received 0.5% chlorfenapyr spray (Phantom) after the nonchemical treatments. All apartments were monitored bi-weekly and retreated when necessary. After 10 wk, bed bugs were eradicated from 50% of the apartments in each group. Bed bug count reduction (mean +/- SEM) was 97.6 +/- 1.6 and 89.7 +/- 7.3% in the D-IPM and S-IPM groups, respectively. Mean treatment costs in the 10-wk period were $463 and $482 per apartment in the D-IPM and S-IPM groups, respectively. Bed bug interceptors trapped an average of 219 +/- 135 bed bugs per apartment in 10 wk. The interceptors contributed to the IPM program efficacy and were much more effective than visual inspections in estimating bed bug numbers and determining the existence of bed bug infestations.

Mother-child bed-sharing trajectories and psychiatric disorders at the age of 6 years.

PubMed

Santos, Iná S; Barros, Aluísio Jd; Barros, Fernando C; Munhoz, Tiago N; Da Silva, Bianca Del Ponte; Matijasevich, Alicia

2017-01-15

Little is known about the effect of bed-sharing with the mother over the child mental health. Population-based birth cohort conducted in Pelotas, Brazil. Children were enrolled at birth (n=4231) and followed-up at 3 months and at 1, 2, 4, and 6 years of age. Bed-sharing was defined as "habitual sharing of the bed between the child and the mother, for sleeping, for part of the night or the whole night". Trajectories of bed sharing between 3 months and 6 years of age were calculated. Mental health was assessed at the age of 6 years using the Development and Well-Being Assessment instrument that generates psychiatric diagnosis according to ICD-10 and DSM-IV criteria. Odds ratios (OR) with 95% confidence intervals were obtained by multivariate logistic regression. 3583 children were analyzed. Four trajectories were identified: non bed-sharers (44.4%), early-only (36.2%), late-onset (12.0%), and persistent bed-sharers (7.4%). In the adjusted analyses persistent bed-sharers were at increased odds of presenting any psychiatric disorder (OR=1.7; 1.2-2.5) and internalizing problems (OR=2.1; 1.4-3.1), as compared to non bed-sharers. Among the early-only bed-sharers OR for any psychiatric disorder was 1.4 (1.1-1.8) and for internalizing problems 1.6 (1.2-2.1). Although the effect of bed-sharing was adjusted for several covariates including the family socio-economic status, maternal mental health and excessive crying, there was no information on maternal personal reasons for bed-sharing. Mothers that bed-share intentionally and those that bed-share in reaction to a child sleep problem may have a different interpretation of their children behavior that may bias the study results. Bed-sharing is a common practice in our setting and is associated with impaired child mental health at the age of six years. Copyright © 2016 The Authors. Published by Elsevier B.V. All rights reserved.

In-Bed Accountability Development for a Passively Cooled, Electrically Heated Hydride (PACE) Bed

DOE Office of Scientific and Technical Information (OSTI.GOV)

Klein, J.E.

A nominal 1500 STP-L PAssively Cooled, Electrically heated hydride (PACE) Bed has been developed for implementation into a new Savannah River Site tritium project. The 1.2 meter (four-foot) long process vessel contains on internal 'U-tube' for tritium In-Bed Accountability (IBA) measurements. IBA will be performed on six, 12.6 kg production metal hydride storage beds.IBA tests were done on a prototype bed using electric heaters to simulate the radiolytic decay of tritium. Tests had gas flows from 10 to 100 SLPM through the U-tube or 100 SLPM through the bed's vacuum jacket. IBA inventory measurement errors at the 95% confidence levelmore » were calculated using the correlation of IBA gas temperature rise, or (hydride) bed temperature rise above ambient temperature, versus simulated tritium inventory.Prototype bed IBA inventory errors at 100 SLPM were the largest for gas flows through the vacuum jacket: 15.2 grams for the bed temperature rise and 11.5 grams for the gas temperature rise. For a 100 SLPM U-tube flow, the inventory error was 2.5 grams using bed temperature rise and 1.6 grams using gas temperature rise. For 50 to 100 SLPM U-tube flows, the IBA gas temperature rise inventory errors were nominally one to two grams that increased above four grams for flows less than 50 SLPM. For 50 to 100 SLPM U-tube flows, the IBA bed temperature rise inventory errors were greater than the gas temperature rise errors, but similar errors were found for both methods at gas flows of 20, 30, and 40 SLPM.Electric heater IBA tests were done for six production hydride beds using a 45 SLPM U-tube gas flow. Of the duplicate runs performed on these beds, five of the six beds produced IBA inventory errors of approximately three grams: consistent with results obtained in the laboratory prototype tests.« less

In-Bed Accountability Development for a Passively Cooled, Electrically Heated Hydride (PACE) Bed

DOE Office of Scientific and Technical Information (OSTI.GOV)

KLEIN, JAMES

A nominal 1500 STP-L PAssively Cooled, Electrically heated hydride (PACE) Bed has been developed for implementation into a new Savannah River Site tritium project. The 1.2 meter (four-foot) long process vessel contains an internal ''U-tube'' for tritium In-Bed Accountability (IBA) measurements. IBA will be performed on six, 12.6 kg production metal hydride storage beds. IBA tests were done on a prototype bed using electric heaters to simulate the radiolytic decay of tritium. Tests had gas flows from 10 to 100 SLPM through the U-tube or 100 SLPM through the bed's vacuum jacket. IBA inventory measurement errors at the 95 percentmore » confidence level were calculated using the correlation of IBA gas temperature rise, or (hydride) bed temperature rise above ambient temperature, versus simulated tritium inventory. Prototype bed IBA inventory errors at 100 SLPM were the largest for gas flows through the vacuum jacket: 15.2 grams for the bed temperature rise and 11.5 grams for the gas temperature rise. For a 100 SLPM U-tube flow, the inventory error was 2.5 grams using bed temperature rise and 1.6 grams using gas temperature rise. For 50 to 100 SLPM U-tube flows, the IBA gas temperature rise inventory errors were nominally one to two grams that increased above four grams for flows less than 50 SLPM. For 50 to 100 SLPM U-tube flows, the IBA bed temperature rise inventory errors were greater than the gas temperature rise errors, but similar errors were found for both methods at gas flows of 20, 30, and 40 SLPM. Electric heater IBA tests were done for six production hydride beds using a 45 SLPM U-tube gas flow. Of the duplicate runs performed on these beds, five of the six beds produced IBA inventory errors of approximately three grams: consistent with results obtained in the laboratory prototype tests.« less

Complex channel responses to changes in stream flow and sediment supply on the lower Duchesne River, Utah

USGS Publications Warehouse

Gaeuman, D.; Schmidt, J.C.; Wilcock, P.R.

2005-01-01

Channel responses to flow depletions in the lower Duchesne River over the past 100 years have been highly complex and variable in space and time. In general, sand-bed reaches adjusted to all perturbations with bed-level changes, whereas the gravel-bed reaches adjusted primarily through width changes. Gravel-bed reaches aggraded only when gravel was supplied to the channel through local bank erosion and degraded only during extreme flood events. A 50% reduction in stream flow and an increase in fine sediment supply to the study area occurred in the first third of the 20th century. The gravel-bed reach responded primarily with channel narrowing, whereas bed aggradation and four large-scale avulsions occurred in the sand-bed reaches. These avulsions almost completely replaced a section of sinuous channel about 14 km long with a straighter section about 7 km long. The most upstream avulsion, located near a break in valley slope and the transition from a gravel bed upstream and a sand bed downstream, transformed a sinuous sand-bed reach into a braided gravel-bed reach and eventually into a meandering gravel-bed reach over a 30-year period. Later, an increase in flood magnitudes and durations caused widening and secondary bed aggradation in the gravel-bed reaches, whereas the sand-bed reaches incised and narrowed. Water diversions since the 1950s have progressively eliminated moderate flood events, whereas larger floods have been less affected. The loss of frequent flooding has increased the duration and severity of drought periods during which riparian vegetation can establish along the channel margins. As a result, the channel has gradually narrowed throughout the study area since the late 1960s, despite the occasional occurrence of large floods. No tributaries enter the Duchesne River within the study area, so all reaches have experienced identical changes in stream flow and upstream sediment supply. ?? 2004 Elsevier B.V. All rights reserved.

Volatile organic compound adsorption in a gas-solid fluidized bed.

PubMed

Ng, Y L; Yan, R; Tsen, L T S; Yong, L C; Liu, M; Liang, D T

2004-01-01

Fluidization finds many process applications in the areas of catalytic reactions, drying, coating, combustion, gasification and microbial culturing. This work aims to compare the dynamic adsorption characteristics and adsorption rates in a bubbling fluidized bed and a fixed bed at the same gas flow-rate, gas residence time and bed height. Adsorption with 520 ppm methanol and 489 ppm isobutane by the ZSM-5 zeolite of different particle size in the two beds enabled the differentiation of the adsorption characteristics and rates due to bed type, intraparticle mass transfer and adsorbate-adsorbent interaction. Adsorption of isobutane by the more commonly used activated carbon provided the comparison of adsorption between the two adsorbent types. With the same gas residence time of 0.79 seconds in both the bubbling bed and fixed bed of the same bed size of 40 mm diameter and 48 mm height, the experimental results showed a higher rate of adsorption in the bubbling bed as compared to the fixed bed. Intraparticle mass transfer and adsorbent-adsorbate interaction played significant roles in affecting the rate of adsorption, with intraparticle mass transfer being more dominant. The bubbling bed was observed to have a steeper decline in adsorption rate with respect to increasing outlet concentration compared to the fixed bed. The adsorption capacities of zeolite for the adsorbates studied were comparatively similar in both beds; fluidizing, and using smaller particles in the bubbling bed did not increase the adsorption capacity of the ZSM-5 zeolite. The adsorption capacity of activated carbon for isobutane was much higher than the ZSM-5 zeolite for isobutane, although at a lower adsorption rate. Fourier transform infra-red (FTIR) spectroscopy was used as an analytical tool for the quantification of gas concentration. Calibration was done using a series of standards prepared by in situ dilution with nitrogen gas, based on the ideal gas law and relating partial pressure to gas concentration. Concentrations up to 220 ppm for methanol and 75 ppm for isobutane were prepared using this method.

Seaweed beds support more juvenile reef fish than seagrass beds in a south-western Atlantic tropical seascape

NASA Astrophysics Data System (ADS)

Eggertsen, L.; Ferreira, C. E. L.; Fontoura, L.; Kautsky, N.; Gullström, M.; Berkström, C.

2017-09-01

Seascape connectivity is regarded essential for healthy reef fish communities in tropical shallow systems. A number of reef fish species use separate adult and nursery habitats, and hence contribute to nutrient and energy transfer between habitats. Seagrass beds and mangroves often constitute important nursery habitats, with high structural complexity and protection from predation. Here, we investigated if reef fish assemblages in the tropical south-western Atlantic demonstrate ontogenetic habitat connectivity and identify possible nurseries on three reef systems along the eastern Brazilian coast. Fish were surveyed in fore reef, back reef, Halodule wrightii seagrass beds and seaweed beds. Seagrass beds contained lower abundances and species richness of fish than expected, while Sargassum-dominated seaweed beds contained significantly more juveniles than all other habitats (average juvenile fish densities: 32.6 per 40 m2 in Sargassum beds, 11.2 per 40 m2 in back reef, 10.1 per 40 m2 in fore reef, and 5.04 per 40 m2 in seagrass beds), including several species that are found in the reef habitats as adults. Species that in other regions worldwide (e.g. the Caribbean) utilise seagrass beds as nursery habitats were here instead observed in Sargassum beds or back reef habitats. Coral cover was not correlated to adult fish distribution patterns; instead, type of turf was an important variable. Connectivity, and thus pathways of nutrient transfer, seems to function differently in east Brazil compared to many tropical regions. Sargassum-dominated beds might be more important as nurseries for a larger number of fish species than seagrass beds. Due to the low abundance of structurally complex seagrass beds we suggest that seaweed beds might influence adult reef fish abundances, being essential for several keystone species of reef fish in the tropical south-western Atlantic.

Preferences for paper bedding material of the laboratory mice.

PubMed

Ago, Akio; Gonda, Tatuo; Takechi, Mayumi; Takeuchi, Takashi; Kawakami, Kohei

2002-04-01

In order to identify indicators of the preferences for bedding materials, the paper bedding material preferences of laboratory mice were investigated in the present study. Four cages, each containing a different structure of paper bedding material were connected to allow free access to each cage. The preferences for paper bedding materials of laboratory mice were judged by the differences in the length of stay and sleep in each cage. The mice preferred the bedding material that allowed them to easily hide and build nests and was soft. We conclude that the comfort and well-being of laboratory mice can be increased through the appropriate selection of bedding material.

Fluidized bed heat exchanger utilizing angularly extending heat exchange tubes

DOEpatents

Talmud, Fred M.; Garcia-Mallol, Juan-Antonio

1980-01-01

A fluidized bed heat exchanger in which air is passed through a bed of particulate material containing fuel disposed in a housing. A steam/water natural circulation system is provided and includes a steam drum disposed adjacent the fluidized bed and a series of tubes connected at one end to the steam drum. A portion of the tubes are connected to a water drum and in the path of the air and the gaseous products of combustion exiting from the bed. Another portion of the tubes pass through the bed and extend at an angle to the upper surface of the bed.

25. Typical valves used to control flow into and out ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

25. Typical valves used to control flow into and out of filtration bed. Left valve (painted red) drains the bed, and center valve (painted green) admits water into the bed. The right valve is a cross over valve which is used to admit water into a dry bed from the bottom. This bottom fill excludes entrapped air as the bed is filled. When the water reached to top of the bed, filling is continued from the top of the bed. - Lake Whitney Water Filtration Plant, Filtration Plant, South side of Armory Street between Edgehill Road & Whitney Avenue, Hamden, New Haven County, CT

Internal dust recirculation system for a fluidized bed heat exchanger

DOEpatents

Gamble, Robert L.; Garcia-Mallol, Juan A.

1981-01-01

A fluidized bed heat exchanger in which air is passed through a bed of particulate material containing fuel disposed in a housing. A steam/water natural circulation system is provided in a heat exchange relation to the bed and includes a steam drum disposed adjacent the bed and a tube bank extending between the steam drum and a water drum. The tube bank is located in the path of the effluent gases exiting from the bed and a baffle system is provided to separate the solid particulate matter from the effluent gases. The particulate matter is collected and injected back into the fluidized bed.

A preliminary evaluation of the potential of Beauveria bassiana for bed bug control.

PubMed

Barbarin, Alexis M; Jenkins, Nina E; Rajotte, Edwin G; Thomas, Matthew B

2012-09-15

Residual biopesticide treatments of Beauveria bassiana were tested against the bed bug Cimex lectularius. An oil formulation of conidia was applied to different substrates. Bed bugs were exposed for 1 h, transferred to an unsprayed environment and monitored for mortality. Separate bioassays evaluated the effect of bed bug strain, sex, life stage, and exposure substrate on mortality. Rapid mortality was observed in all bioassays, with bed bugs exposed to treated jersey knit cotton dying most rapidly. A further assay demonstrated efficient autodissemination of conidia from exposed bed bugs to unexposed bed bugs within artificial harborages. Copyright © 2012 Elsevier Inc. All rights reserved.

Bed Bugs

EPA Pesticide Factsheets

Prevent, identify, and treat bed bug infestations using EPA’s step-by-step guides, based on IPM principles. Find pesticides approved for bed bug control, check out the information clearinghouse, and dispel bed bug myths.

Change in attachment states of mind of women with binge-eating disorder.

PubMed

Maxwell, Hilary; Tasca, Giorgio A; Grenon, Renee; Ritchie, Kerri; Bissada, Hany; Balfour, Louise

2017-11-01

Insecure and unresolved/disorganized attachment states of mind may impact affect regulation and interpersonal functioning that contribute to binge eating in women with binge-eating disorder (BED). Group psychological treatment may facilitate changes from insecure to secure and from unresolved-disorganized to non-unresolved/disorganized attachment states of mind. This study used attachment theory to understand better the psychopathology of BED and co-morbid overweight status and to understand better the treatment response of patients with BED who receive group psychotherapy. Women with BED attended group psychodynamic interpersonal psychotherapy and completed the Adult Attachment Interview pretreatment and 6 months posttreatment. Matched samples of overweight women without BED and normal-weight women without BED completed the Adult Attachment Interview at 1 time point. Women with BED had significantly higher rates of preoccupied and unresolved/disorganized attachment states of mind compared to normal-weight women without BED and had similar rates of insecure and unresolved/disorganized attachment states of mind compared to overweight women without BED. Of the women with BED who had an insecure and/or unresolved/disorganized attachment states of mind at pretreatment, about 60% demonstrated clinically relevant changes to secure and to non-unresolved/disorganized states of mind at 6 months post group psychodynamic interpersonal psychotherapy. Results indicated that some women with BED may benefit from interventions that help them regulate hyperactivated affect and create coherent narratives. Both women with BED and overweight women without BED may benefit from treatments that help them develop more adaptive affect regulation strategies related to unresolved/disorganized attachment states of mind. Copyright © 2017 John Wiley & Sons, Ltd.

Thermal insulation and SIDS-an investigation of selected 'Eastern' and 'Western' infant bedding combinations.

PubMed

Wilson, C A; Chu, M S

2005-08-01

Differences in the incidence of SIDS between 'Western' and 'Eastern' countries has been attributed to cultural practices, which may affect the infants care and thermal environment. The purpose of this work was to estimate for selected 'commonly' used bedding, sleep positions and practices in Japan, Korea and New Zealand, the intrinsic 'dry' thermal resistance of bedding. Insulation levels are also discussed in the context of published information about the thermal environment in which the bedding is likely to be used. Selected Japanese, Korean and New Zealand bedding was loosely tucked over an infant manikin in the lateral, prone and supine sleep positions. Thickness in use was measured, and intrinsic 'dry' thermal resistance estimated using the Wilson Laing model which accommodates the effect on insulation of the three-dimensional arrangement of bedding combinations during use. Thickness of under- and upper-bedding varied among countries with thickness and estimated 'dry' thermal resistance of the upper-bedding affected by the type/combination of bedding and the infants sleep position. Insulation levels are discussed in relation to environmental conditions within and among countries and between seasons. Further information on thermal environments, bedding combinations used and care practices within both Asian and Western countries is needed. 'Eastern' infants appear likely to be generally covered in bedding combinations of greater insulation than those used to cover 'Western' infants in comparable seasons. Differences existed between insulation of the Japanese and Korean bedding combinations investigated. Lower rates of SIDS apparent in 'Asian' populations do not appear attributable to use of lower levels of bedding insulation only.

A bioassay for studying behavioural responses of the common bed bug, Cimex lectularius (Hemiptera: Cimicidae) to bed bug-derived volatiles.

PubMed

Weeks, E N I; Logan, J G; Gezan, S A; Woodcock, C M; Birkett, M A; Pickett, J A; Cameron, M M

2011-02-01

The common bed bug, Cimex lectularius (Hemiptera: Cimicidae), has recently re-emerged in increasing numbers, distribution and intensity of infestation in many countries. Current control relies on the application of residual pesticides; but, due to the development of insecticide resistance, there is a need for new tools and techniques. Semiochemicals (behaviour and physiology modifying chemicals) could be exploited for management of bed bugs. However, in order to identify semiochemicals that can be utilised in monitoring or control, a suitable olfactometer is needed that enables the study of the responses of bed bugs to volatile chemicals. Previous studies have used olfactometers that do not separate olfactory responses from responses to physical contact. In this study, a still-air olfactometer was used to measure behavioural responses to different bed bug-derived volatiles presented in an odour pot. Bed bugs were significantly more likely to visit the area above the odour pot first, and more frequently, in the presence of volatiles from bed bug-exposed paper but not in the presence of volatiles from conspecific bed bugs. Bed bug activity was found to be dependent on the presence of the volatiles from bed bug-exposed paper, the time during the scotophase and the sex of the insect being tested. The still-air olfactometer could be used to test putative semiochemicals, which would allow an understanding of their behavioural role in bed bug ecology. Ultimately, this could lead to the identification of new semiochemical tools for bed bug monitoring and control.

Bed Surface Adjustments to Spatially Variable Flow in Low Relative Submergence Regimes

NASA Astrophysics Data System (ADS)

Monsalve, A.; Yager, E. M.

2017-11-01

In mountainous rivers, large relatively immobile grains partly control the local and reach-averaged flow hydraulics and sediment fluxes. When the flow depth is similar to the size of these grains (low relative submergence), heterogeneous flow structures and plunging flow cause spatial distributions of bed surface elevations, textures, and sedimentation rates. To explore how the bed surface responds to these flow variations we conducted a set of experiments in which we varied the relative submergence of staggered hemispheres (simulated large boulders) between runs. All experiments had the same average sediment transport capacity, upstream sediment supply, and initial bed thickness and grain size distribution. We combined our laboratory measurements with a 3-D flow model to obtain the detailed flow structure around the hemispheres. The local bed shear stress field displayed substantial variability and controlled the bed load transport rates and direction in which sediment moved. The divergence in bed shear stress caused by the hemispheres promoted size-selective bed load deposition, which formed patches of coarse sediment upstream of the hemisphere. Sediment deposition caused a decrease in local bed shear stress, which combined with the coarser grain size, enhanced the stability of this patch. The region downstream of the hemispheres was largely controlled by a recirculation zone and had little to no change in grain size, bed elevation, and bed shear stress. The formation, development, and stability of sediment patches in mountain streams is controlled by the bed shear stress divergence and magnitude and direction of the local bed shear stress field.

Experimental System of Solar Adsorption Refrigeration with Concentrated Collector.

PubMed

Yuan, Z X; Li, Y X; Du, C X

2017-10-18

To improve the performance of solar adsorption refrigeration, an experimental system with a solar concentration collector was set up and investigated. The main components of the system were the adsorbent bed, the condenser, the evaporator, the cooling sub-system, and the solar collector. In the first step of the experiment, the vapor-saturated bed was heated by the solar radiation under closed conditions, which caused the bed temperature and pressure to increase. When the bed pressure became high enough, the bed was switched to connect to the condenser, thus water vapor flowed continually from the bed to the condenser to be liquefied. Next, the bed needed to cool down after the desorption. In the solar-shielded condition, achieved by aluminum foil, the circulating water loop was opened to the bed. With the water continually circulating in the bed, the stored heat in the bed was took out and the bed pressure decreased accordingly. When the bed pressure dropped below the saturation pressure at the evaporation temperature, the valve to the evaporator was opened. A mass of water vapor rushed into the bed and was adsorbed by the zeolite material. With the massive vaporization of the water in the evaporator, the refrigeration effect was generated finally. The experimental result has revealed that both the COP (coefficient of the performance of the system) and the SCP (specific cooling power of the system) of the SAPO-34 zeolite was greater than that of the ZSM-5 zeolite, no matter whether the adsorption time was longer or shorter. The system of the SAPO-34 zeolite generated a maximum COP of 0.169.

Scaling relationships between bed load volumes, transport distances, and stream power in steep mountain channels

NASA Astrophysics Data System (ADS)

Schneider, Johannes M.; Turowski, Jens M.; Rickenmann, Dieter; Hegglin, Ramon; Arrigo, Sabrina; Mao, Luca; Kirchner, James W.

2014-03-01

Bed load transport during storm events is both an agent of geomorphic change and a significant natural hazard in mountain regions. Thus, predicting bed load transport is a central challenge in fluvial geomorphology and natural hazard risk assessment. Bed load transport during storm events depends on the width and depth of bed scour, as well as the transport distances of individual sediment grains. We traced individual gravels in two steep mountain streams, the Erlenbach (Switzerland) and Rio Cordon (Italy), using magnetic and radio frequency identification tags, and measured their bed load transport rates using calibrated geophone bed load sensors in the Erlenbach and a bed load trap in the Rio Cordon. Tracer transport distances and bed load volumes exhibited approximate power law scaling with both the peak stream power and the cumulative stream energy of individual hydrologic events. Bed load volumes scaled much more steeply with peak stream power and cumulative stream energy than tracer transport distances did, and bed load volumes scaled as roughly the third power of transport distances. These observations imply that large bed load transport events become large primarily by scouring the bed deeper and wider, and only secondarily by transporting the mobilized sediment farther. Using the sediment continuity equation, we can estimate the mean effective thickness of the actively transported layer, averaged over the entire channel width and the duration of individual flow events. This active layer thickness also followed approximate power law scaling with peak stream power and cumulative stream energy and ranged up to 0.57 m in the Erlenbach, broadly consistent with independent measurements.

The variability of critical care bed numbers in Europe.

PubMed

Rhodes, A; Ferdinande, P; Flaatten, H; Guidet, B; Metnitz, P G; Moreno, R P

2012-10-01

To quantify the numbers of critical care beds in Europe and to understand the differences in these numbers between countries when corrected for population size and gross domestic product. Prospective data collection of critical care bed numbers for each country in Europe from July 2010 to July 2011. Sources were identified in each country that could provide data on numbers of critical care beds (intensive care and intermediate care). These data were then cross-referenced with data from international databases describing population size and age, gross domestic product (GDP), expenditure on healthcare and numbers of acute care beds. We identified 2,068,892 acute care beds and 73,585 (2.8 %) critical care beds. Due to the heterogeneous descriptions of these beds in the individual countries it was not possible to discriminate between intensive care and intermediate care in most cases. On average there were 11.5 critical care beds per 100,000 head of population, with marked differences between countries (Germany 29.2, Portugal 4.2). The numbers of critical care beds per country corrected for population size were positively correlated with GDP (r(2) = 0.16, p = 0.05), numbers of acute care beds corrected for population (r(2) = 0.12, p = 0.05) and the percentage of acute care beds designated as critical care (r(2) = 0.59, p < 0.0001). They were not correlated with the proportion of GDP expended on healthcare. Critical care bed numbers vary considerably between countries in Europe. Better understanding of these numbers should facilitate improved planning for critical care capacity and utilization in the future.

Impulsivity in binge eating disorder: food cues elicit increased reward responses and disinhibition.

PubMed

Schag, Kathrin; Teufel, Martin; Junne, Florian; Preissl, Hubert; Hautzinger, Martin; Zipfel, Stephan; Giel, Katrin Elisabeth

2013-01-01

Binge eating disorder (BED) represents a distinct eating disorder diagnosis. Current approaches assume increased impulsivity to be one factor leading to binge eating and weight gain. We used eye tracking to investigate both components of impulsivity, namely reward sensitivity and rash-spontaneous behaviour towards food in BED for the first time. Overweight and obese people with BED (BED+; n = 25), without BED (BED-; n = 26) and healthy normal-weight controls (NWC; n = 25) performed a free exploration paradigm measuring reward sensitivity (experiment 1) and a modified antisaccade paradigm measuring disinhibited, rash-spontaneous behaviour (experiment 2) using food and nonfood stimuli. Additionally, trait impulsivity was assessed. In experiment 1, all participants located their initial fixations more often on food stimuli and BED+ participants gazed longer on food stimuli in comparison with BED- and NWC participants. In experiment 2, BED+ participants had more difficulties inhibiting saccades towards food and nonfood stimuli compared with both other groups in first saccades, and especially towards food stimuli in second saccades and concerning sequences of first and second saccades. BED- participants did not differ significantly from NWC participants in both experiments. Additionally, eye tracking performance was associated with self-reported reward responsiveness and self-control. According to these results, food-related reward sensitivity and rash-spontaneous behaviour, as the two components of impulsivity, are increased in BED in comparison with weight-matched and normal-weight controls. This indicates that BED represents a neurobehavioural phenotype of obesity that is characterised by increased impulsivity. Interventions for BED should target these special needs of affected patients.

Vision in the common bed bug Cimex lectularius L. (Hemiptera: Cimicidae): eye morphology and spectral sensitivity.

PubMed

McNeill, C A; Allan, S A; Koehler, P G; Pereira, R M; Weeks, E N I

2016-12-01

Bed bugs as pests of public health importance recently experienced a resurgence in populations throughout the U.S. and other countries. Consequently, recent research efforts have focused on improving understanding of bed bug physiology and behaviour to improve management. While few studies have investigated the visual capabilities of bed bugs, the present study focused specifically on eye morphology and spectral sensitivity. A 3-D imaging technique was used to document bed bug eye morphology from the first instar through adult and revealed morphological characteristics that differentiate the common bed bug from the tropical bed bug as well as sex-specific differences. Electrophysiological measurements were used to evaluate the spectral sensitivity of adult bed bugs. Male bed bugs were more responsive than females at some wavelengths. Electrophysiological studies provided evidence for at least one photoreceptor with a spectral sensitivity curve peak in the green (λ max 520 nm) region of the spectrum. The broadened long wavelength portion of the spectral sensitivity curve may potentially indicate another photoreceptor in the yellow-green (λ max 550 nm) portion of the spectrum or screening pigments. Understanding more about bed bug visual biology is vital for designing traps, which are an important component of integrated bed bug management. © 2016 The Royal Entomological Society.

The ecosystem service value of living versus dead biogenic reef

NASA Astrophysics Data System (ADS)

Sheehan, E. V.; Bridger, D.; Attrill, M. J.

2015-03-01

Mixed maerl beds (corralline red algae) comprise dead thalli with varying amounts of live maerl fragments, but previously it was not known whether the presence of the live maerl increases the ecosystem service 'habitat provision' of the dead maerl for the associated epibenthos. A 'flying array' towed sled with high definition video was used to film transects of the epibenthos in dead maerl and mixed maerl beds in two locations to the north and south of the English Channel (Falmouth and Jersey). Mixed maerl beds supported greater number of taxa and abundance than dead beds in Falmouth, while in Jersey, mixed and dead beds supported similar number of taxa and dead beds had a greater abundance of epifauna. Scallops tended to be more abundant on mixed beds than dead beds. Tube worms were more abundant on mixed beds in Falmouth and dead beds in Jersey. An increasing percentage occurrence of live maerl thalli correlated with increasing number of taxa in Falmouth but not Jersey. It was concluded that while live thalli can increase the functional role of dead maerl beds for the epibenthos, this is dependent on location and response variable. As a result of this work, maerl habitat in SE Jersey has been protected from towed demersal fishing gear.

Spitzer Digs Up Hidden Stars

NASA Technical Reports Server (NTRS)

2007-01-01

[figure removed for brevity, see original site] 3-Panel Version Figure 1 [figure removed for brevity, see original site] [figure removed for brevity, see original site] [figure removed for brevity, see original site] Visible Light Figure 2 Infrared (IRAC) Figure 3 Combined Figure 4

Two rambunctious young stars are destroying their natal dust cloud with powerful jets of radiation, in an infrared image from NASA's Spitzer Space Telescope.

The stars are located approximately 600 light-years away in a cosmic cloud called BHR 71. In visible light (left panel), BHR 71 is just a large black structure. The burst of yellow light toward the bottom of the cloud is the only indication that stars might be forming inside. In infrared light (center panel), the baby stars are shown as the bright yellow smudges toward the center. Both of these yellow spots have wisps of green shooting out of them. The green wisps reveal the beginning of a jet. Like a rainbow, the jet begins as green, then transitions to orange, and red toward the end. The combined visible-light and infrared composite (right panel) shows that a young star's powerful jet is responsible for the rupture at the bottom of the dense cloud in the visible-light image. Astronomers know this because burst of light in the visible-light image overlaps exactly with a jet spouting-out of the left star, in the infrared image.

The jets' changing colors reveal a cooling effect, and may suggest that the young stars are spouting out radiation in regular bursts. The green tints at the beginning of the jet reveal really hot hydrogen gas, the orange shows warm gas, and the reddish wisps at the end represent the coolest gas. The fact that gas toward the beginning of the jet is hotter than gas near the middle suggests that the stars must give off regular bursts of energy -- and the material closest to the star is being heated by shockwaves from a recent stellar outburst. Meanwhile, the tints of orange reveal gas that is currently being heated by shockwaves from a previous stellar outburst. By the time these shockwaves reach the end of the jet, they have slowed down so significantly that the gas is only heated a little, and looks red. The combination of views also brings out some striking details that evaded visible-light detection. For example, the yellow dots scattered throughout the image are actually young stars forming inside BHR 71. Spitzer also uncovered another young star with jets, located to the right of the powerful jet seen in the visible-light image. Spitzer can see details that visible-light telescopes don't, because its infrared instruments are sensitive to 'heat.'

The infrared image is made up of data from Spitzer's infrared array camera. Blue shows infrared light at 3.6 microns, green is light at 4.5 microns, and red is light at 8.0 microns.

Early processing variations in selective attention to the color and direction of moving stimuli during 30 days head-down bed rest

NASA Astrophysics Data System (ADS)

Wang, Lin-Jie; He, Si-Yang; Niu, Dong-Bin; Guo, Jian-Ping; Xu, Yun-Long; Wang, De-Sheng; Cao, Yi; Zhao, Qi; Tan, Cheng; Li, Zhi-Li; Tang, Guo-Hua; Li, Yin-Hui; Bai, Yan-Qiang

2013-11-01

Dynamic variations in early selective attention to the color and direction of moving stimuli were explored during a 30 days period of head-down bed rest. Event-related potentials (ERPs) were recorded at F5, F6, P5, P6 scalp locations in seven male subjects who attended to pairs of bicolored light emitting diodes that flashed sequentially to produce a perception of movement. Subjects were required to attend selectively to a critical feature of the moving target, e.g., color or direction. The tasks included: a no response task, a color selective response task, a moving direction selective response task, and a combined color-direction selective response task. Subjects were asked to perform these four tasks on: the 3rd day before bed rest; the 3rd, 15th and 30th day during the bed rest; and the 5th day after bed rest. Subjects responded quickly to the color than moving direction and combined color-direction response. And they had a longer reaction time during bed rest on the 15th and 30th day during bed rest after a relatively quicker response on the 3rd day. Using brain event-related potentials technique, we found that in the color selective response task, the mean amplitudes of P1 and N1 for target ERPs decreased in the 3rd day during bed rest and 5th day after bed rest in comparison with pre-bed rest, 15th day and 30th day during bed rest. In the combined color-direction selective response task, the P1 latencies for target ERPs on the 3rd and 30th day during bed rest were longer than on the 15th day during bed rest. As 3rd day during bed rest was in the acute adaptation period and 30th day during bed rest was in the relatively adaptation stage of head-down bed rest, the results help to clarify the effects of bed rest on different task loads and patterns of attention. It was suggested that subjects expended more time to give correct decision in the head-down tilt bed rest state. A difficulty in the recruitment of brain resources was found in feature selection task, but no variations were detected in the no response and direction selective response tasks. It is suggested that the negative shift in color selective response task on the 3rd day of bed rest are a result of fluid redistribution. And feature selection was more affected than motion selection in the head down bed rest. The variations in cognitive processing speed observed for the combined color-direction selective response task are suggested to reflect the interaction between top-down mechanisms and hierarchical physiological characteristics during 30 days head-down bed rest.

The dominance of dispersion in the evolution of bed material waves in gravel-bed rivers

Treesearch

Thomas E. Lisle; Yantao Cui; Gary Parker; James E. Pizzuto; Annjanette M. Dodd

2001-01-01

Abstract - Bed material waves are temporary zones of sediment accumulation created by large sediment inputs. Recent theoretical, experimental and field studies examine factors in fluencing dispersion and translation of bed material waves in quasi-uniform, gravel-bed channels. Exchanges of sediment between a channel and its floodplain are...

Bed load transport in gravel-bed rivers

Treesearch

Jeffrey J. Barry

2007-01-01

Bed load transport is a fundamental physical process in alluvial rivers, building and maintaining a channel geometry that reflects both the quantity and timing of water and the volume and caliber of sediment delivered from the watershed. A variety of formulae have been developed to predict bed load transport in gravel-bed rivers, but testing of the equations in natural...

The Relationship between Parent-Infant Bed Sharing and Marital Satisfaction for Mothers of Infants

ERIC Educational Resources Information Center

Messmer, Rosemary; Miller, Lynn D.; Yu, Christine M.

2012-01-01

This study investigated the relationship between marital satisfaction and time spent bed sharing with infants in a community sample of 81 bed sharing mothers. Time spent bed sharing did not significantly predict variance in marital satisfaction when considering bed sharers as a whole. Moderation analysis, however, showed the interaction between…

A low tritium hydride bed inventory estimation technique

DOE Office of Scientific and Technical Information (OSTI.GOV)

Klein, J.E.; Shanahan, K.L.; Baker, R.A.

2015-03-15

Low tritium hydride beds were developed and deployed into tritium service in Savannah River Site. Process beds to be used for low concentration tritium gas were not fitted with instrumentation to perform the steady-state, flowing gas calorimetric inventory measurement method. Low tritium beds contain less than the detection limit of the IBA (In-Bed Accountability) technique used for tritium inventory. This paper describes two techniques for estimating tritium content and uncertainty for low tritium content beds to be used in the facility's physical inventory (PI). PI are performed periodically to assess the quantity of nuclear material used in a facility. Themore » first approach (Mid-point approximation method - MPA) assumes the bed is half-full and uses a gas composition measurement to estimate the tritium inventory and uncertainty. The second approach utilizes the bed's hydride material pressure-composition-temperature (PCT) properties and a gas composition measurement to reduce the uncertainty in the calculated bed inventory.« less

Cognitive Functioning in Long Duration Head-down Bed Rest

NASA Technical Reports Server (NTRS)

Seaton, Kimberly A.; Slack, Kelley J.; Sipes, Walter A.; Bowie, Kendra

2008-01-01

The Space Flight Cognitive Assessment Tool for Windows (WinSCAT) is a self-administered battery of tests used on the International Space Station for evaluating cognitive functioning. Here, WinSCAT was used to assess cognitive functioning during extended head-down bed rest. Thirteen subjects who participated in 60 or 90 days of 6 deg head-down bed rest took WinSCAT during the pre-bed rest phase, the in-bed rest phase, and the post-bed rest (reconditioning) phase of study participation. After adjusting for individual baseline performance, 12 off-nominal scores were observed out of 351 total observations during bed rest and 7 of 180 during reconditioning. No evidence was found for systematic changes in off-nominal incidence as time in bed rest progressed, or during the reconditioning period. Cognitive functioning does not appear to be adversely affected by long duration head-down bed rest. Individual differences in underlying cognitive ability and motivation level are likely explanations for the current findings.

Tanning bed burns reported on Twitter: over 15,000 in 2013.

PubMed

Seidenberg, Andrew B; Pagoto, Sherry L; Vickey, Theodore A; Linos, Eleni; Wehner, Mackenzie R; Costa, Renata Dalla; Geller, Alan C

2016-06-01

Few surveillance tools exist for monitoring tanning bed injuries. Twitter data were examined to identify and describe reports of tanning bed-caused burns. Tweets sent in 2013 containing keywords for tanning bed use and burning were content analyzed to determine whether a burn caused by a tanning bed was described, and additional data on tanning behavior and burn characteristics were extracted. After content assessment, 15,178 (64 %) tweets were found to describe a tanning bed-caused burn. Sites most reportedly burnt were buttocks (n = 3117), face/head (n = 1020), and chest/breast (n = 546). Alarmingly, 200 burns to the eyes/eyelids were mentioned. A total of 456 tweets described burning >1 time from a tanning bed. A total of 211 tweets mentioned falling asleep inside the tanning bed. In 2013, over 15,000 tweets reported tanning bed-caused burns. Twitter data provides unique insight into tanning behaviors and injuries not captured through traditional public health surveillance.

Temporal variation in bed configuration and one-dimensional bottom roughness at the mid-shelf STRESS site

NASA Astrophysics Data System (ADS)

Wheatcroft, Robert A.

1994-08-01

Time-lapse stereophotographs were taken over a 90-day period from mid-November 1990 to late-February 1991 at a 90-m silt-bottom site on the central California shelf as part of the STRESS (Sediment Transport Events on Shelves and Slopes) project. Five distinct bed configurations were observed, in order of decreasing abundance, these are: (1) bioturbated bed; (2) smoothed bed; (3) current-rippled bed; (4) scour-pitted bed; and (5) wave-rippled bed. Concurrent measurements of the flow field implicate along-shelf currents, rather than waves, as the primary agent forming the physical bed configurations. The presence of a wave-induced cross-shelf gradient in near-bottom suspended sediment during storm events and the redistribution of this sediment by upwelling or downwelling currents is postulated to control the appearance of depositional current-ripples (northwest poleward flow, downwelling) and erosional scour-pits (southeast equatorward flow, upwelling). All physical bed forms are destroyed by bioturbation processes in periods of hours to days. Analytical photogrammetric techniques were used to extract high-resolution sea floor height data from the stereophotographs. Results indicate maximal relief over a 0.25-m 2 area at this site never exceeded 5 cm. Root-mean-square (rms) height varied by a factor of 3 (3.2-9.2 mm) and is a weak function of bed configuration. Current ripples have the largest rms-height, smoothed and scour-pitted beds the smallest. Rms-heights of bioturbated beds are variable and appear to depend on the previously produced physical bed configuration. Changes in rms-height can be abrupt with factor of 2 changes observed over a 12-h period. Horizontal descriptors of roughness such as peak spacing or peak width cannot separate bed configurations. Results from surface slope distributions are broadly coherent with the rms-height data, in that surfaces with large rms-heights have broad slope distributions and vice versa. Slope distribution data also indicate that all bed configurations except the current-rippled bed are isotropic. These preliminary data suggest that time series information is needed to adequately resolve both the micro-scale roughness of the sea floor on continental shelves and the presence of short lived, but potentially flow-diagnostic bed configurations.

Using research and education to implement practical bed bug control programs in multifamily housing.

PubMed

Bennett, Gary W; Gondhalekar, Ameya D; Wang, Changlu; Buczkowski, Grzegorz; Gibb, Timothy J

2016-01-01

Multifamily housing facilities serving low-income populations have been at the forefront of bed bug outbreaks. Research conducted in the past 8 years has consistently proven that integrated pest management (IPM) is the best approach for successful suppression of bed bug infestations. Bed bug IPM in multifamily settings is especially dependent upon a collaborative community or building-wide effort involving residents, building staff and pest control technicians. Other components of a bed bug IPM program include regular monitoring to detect early-stage bed bug infestations and combined use of non-chemical and chemical interventions. Lastly, to reduce reinfestation rates and costs associated with bed bug control, it is critical to continue periodic monitoring and implement preventive control measures even after successful elimination of bed bugs has been achieved. © 2015 Society of Chemical Industry.

Four Bed Molecular Sieve - Exploration (4BMS-X) Virtual Heater Design and Optimization

NASA Technical Reports Server (NTRS)

Schunk, R. Gregory; Peters, Warren T.; Thomas, John T., Jr.

2017-01-01

A 4BMS-X (Four Bed Molecular Sieve - Exploration) design and heater optimization study for CO2 sorbent beds in proposed exploration system architectures is presented. The primary objectives of the study are to reduce heater power and thermal gradients within the CO2 sorbent beds while minimizing channeling effects. Some of the notable changes from the ISS (International Space Station) CDRA (Carbon Dioxide Removal Assembly) to the proposed exploration system architecture include cylindrical beds, alternate sorbents and an improved heater core. Results from both 2D and 3D sorbent bed thermal models with integrated heaters are presented. The 2D sorbent bed models are used to optimize heater power and fin geometry while the 3D models address end effects in the beds for more realistic thermal gradient and heater power predictions.

Potential of Essential Oil-Based Pesticides and Detergents for Bed Bug Control.

PubMed

Singh, Narinderpal; Wang, Changlu; Cooper, Richard

2014-12-01

The bed bug, (Cimex lectularius L.), is a difficult pest to control. Prevalence of insecticide resistance among bed bug populations and concerns over human-insecticide exposure has stimulated the development of alternative bed bug control materials. Many essential oil-based pesticides and detergent insecticides targeting bed bugs have been developed in recent years. We evaluated the efficacy of nine essential oil-based products and two detergents using direct spray and residual contact bioassays in the laboratory. Two conventional insecticides, Temprid SC (imidacloprid and β-cyfluthrin) and Demand CS (λ-cyhalothrin), were used for comparison. Among the 11 nonsynthetic insecticides tested, only EcoRaider (1% geraniol, 1% cedar extract, and 2% sodium lauryl sulfate) and Bed Bug Patrol (0.003% clove oil, 1% peppermint oil, and 1.3% sodium lauryl sulfate) caused >90% mortality of nymphs in direct spray and forced exposure residual assays. However, the efficacy of EcoRaider and Bed Bug Patrol was significantly lower than that of Temprid SC and Demand CS in choice exposure residual bioassay. Direct spray of EcoRaider caused 87% egg mortality, whereas the other nonsynthetic insecticides had little effect on bed bug eggs. EcoRaider and Bed Bug Patrol did not exhibit detectable repellency against bed bugs in the presence of a carbon dioxide source. These findings suggest that EcoRaider and Bed Bug Patrol are potentially useful pesticides for controlling bed bug infestations, but further testing in naturally infested environments is needed. © 2014 Entomological Society of America.

Bugging forecast: unknown, disliked, occasionally intimate. Bed bugs in Germany meet unprepared people.

PubMed

Seidel, Conrad; Reinhardt, Klaus

2013-01-01

Bed bugs appear to be feared more than vector insects and other household pests. The reasons for this exaggerated fear are not fully understood. One hypothesis is that the folk knowledge on recognising and controlling bed bugs decreased as bed bugs became rarer in the 1960s and led to irrational perceptions. Here, we examine people's ability to recognise a bed bug and their response what to do in case of an infestation. We found that 13% of a sample of 391 people in four large German cities recognised a bed bug; 15% of all respondents would call a pest controller in case of bed bug infestation. This results in the pessimistic estimate that 97% of all early-stage infestations could go untreated. We discuss additional scenarios. The effectiveness of efforts to educate people about the presence of bed bugs has never been tested, but our sample is useful to guide future studies. We found three sources of information were associated with increased recognition rates of bed bugs: a) previous contacts with bed bugs (60% recognition), b) knowledge from friends or relatives (25%) and school or education courses (15%). By contrast, people who heard of bed bugs from television, print media or the Internet showed reduced recognition rates. We propose that the former factors be tested for educational interventions. In Germany, the bed bug is an estranged creature to many people, a fact that seems to hinder rational approaches to their control.

Cardiovascular Adaptations to Long Duration Head-Down Tilt Bed Rest

NASA Technical Reports Server (NTRS)

Platts, Steven H.; Martin, David S.; Perez, Sondar A.; Ribeiro, Christine; Stenger, Michael B.; Summers, Richard; Meck, Janice V.

2008-01-01

INTRODUCTION: Orthostatic hypotension is a serious risk for crewmembers returning from spaceflight. Numerous cardiovascular mechanisms have been proposed to account for this problem, including vascular and cardiac dysfunction, which we studied during bed rest. METHODS: Thirteen subjects were studied before and during bed rest. Statistical analysis was limited to the first 49-60 days of bed rest, and compared to pre-bed rest data. Ultrasound data were collected on vascular and cardiac structure and function. Tilt testing was conducted for 30 minutes or until presyncopal symptoms intervened. RESULTS: Plasma volume was significantly reduced by day 7 of bed rest. Flow-mediated dilation in the leg was significantly increased at bed rest day 49. Arterial responses to nitroglycerin differed in the arm and leg, but did not change as a result of bed rest. Intimal-medial thickness markedly decreased at bed rest days 21, 35 and 49. Several cardiac functional parameters including isovolumic relaxation time, ejection time and myocardial performance index were significantly increased (indicating a decrease in cardiac function) during bed rest. There was a trend for decreased orthostatic tolerance following 60 days of bed rest. DISCUSSION: These data suggest that 6 head-down tilt bed rest alters cardiovascular structure and function in a pattern similar to short duration spaceflight. Additionally, the vascular alterations are primarily seen in the lower body, while vessels of the upper body are unaffected. KEY WORDS: spaceflight, orthostatic intolerance, hypotension, fluid-shift, plasma volume

Bugging Forecast: Unknown, Disliked, Occasionally Intimate. Bed Bugs in Germany Meet Unprepared People

PubMed Central

Seidel, Conrad; Reinhardt, Klaus

2013-01-01

Bed bugs appear to be feared more than vector insects and other household pests. The reasons for this exaggerated fear are not fully understood. One hypothesis is that the folk knowledge on recognising and controlling bed bugs decreased as bed bugs became rarer in the 1960s and led to irrational perceptions. Here, we examine people’s ability to recognise a bed bug and their response what to do in case of an infestation. We found that 13% of a sample of 391 people in four large German cities recognised a bed bug; 15% of all respondents would call a pest controller in case of bed bug infestation. This results in the pessimistic estimate that 97% of all early-stage infestations could go untreated. We discuss additional scenarios. The effectiveness of efforts to educate people about the presence of bed bugs has never been tested, but our sample is useful to guide future studies. We found three sources of information were associated with increased recognition rates of bed bugs: a) previous contacts with bed bugs (60% recognition), b) knowledge from friends or relatives (25%) and school or education courses (15%). By contrast, people who heard of bed bugs from television, print media or the Internet showed reduced recognition rates. We propose that the former factors be tested for educational interventions. In Germany, the bed bug is an estranged creature to many people, a fact that seems to hinder rational approaches to their control. PMID:23300947

Assessment of historical exposures in a nickel refinery in Norway.

PubMed

Grimsrud, T K; Berge, S R; Resmann, F; Norseth, T; Andersen, A

2000-08-01

The aim of the study was, on the basis of new information on nickel species and exposure levels, to generate a specific exposure matrix for epidemiologic analyses in a cohort of Norwegian nickel-refinery workers with a known excess of respiratory cancer. A department-time-exposure matrix was constructed with average exposure to total nickel estimated as the arithmetic mean of personal measurements for periods between 1973 and 1994. From 1972 back to the start of production in 1910, exposure concentrations were estimated through retrograde calculation with multiplication factors developed on the basis of reported changes in the metallurgical process and work environment. The relative distribution of water-soluble nickel salts (sulfates and chlorides), metallic nickel, and particulates with limited solubility (sulfides and oxides) was mainly derived from speciation analyses conducted in the 1990s. The average concentration of nickel in the breathing zone was < or = 0.7 mg/m3 for all workers after 1978. Exposure levels for smelter and roaster day workers were 2-6 mg/m3 before 1970, while workers in nickel electrolysis and electrolyte purification were exposed to concentrations in the range of 0.15-1.2 mg/m3. The level of water-soluble nickel was of the same order for workers in the smelting and roasting departments as in some of the electrolyte purification departments. Compared with earlier estimates, the present matrix probably offers a more reliable description of past exposures at the plant.

Comparing ownership and use of bed nets at two sites with differential malaria transmission in western Kenya.

PubMed

Ernst, Kacey C; Hayden, Mary H; Olsen, Heather; Cavanaugh, Jamie L; Ruberto, Irene; Agawo, Maurice; Munga, Stephen

2016-04-14

Challenges persist in ensuring access to and optimal use of long-lasting, insecticidal bed nets (LLINs). Factors associated with ownership and use may differ depending on the history of malaria and prevention control efforts in a specific region. Understanding how the cultural and social-environmental context of bed net use may differ between high- and low-risk regions is important when identifying solutions to improve uptake and appropriate use. Community forums and a household, cross-sectional survey were used to collect information on factors related to bed net ownership and use in western Kenya. Sites with disparate levels of transmission were selected, including an endemic lowland area, Miwani, and a highland epidemic-prone area, Kapkangani. Analysis of ownership was stratified by site. A combined site analysis was conducted to examine factors associated with use of all available bed nets. Logistic regression modelling was used to determine factors associated with ownership and use of owned bed nets. Access to bed nets as the leading barrier to their use was identified in community forums and cross-sectional surveys. While disuse of available bed nets was discussed in the forums, it was a relatively rare occurrence in both sites. Factors associated with ownership varied by site. Education, perceived risk of malaria and knowledge of individuals who had died of malaria were associated with higher bed net ownership in the highlands, while in the lowlands individuals reporting it was easy to get a bed net were more likely to own one. A combined site analysis indicated that not using an available bed net was associated with the attitudes that taking malaria drugs is easier than using a bed net and that use of a bed net will not prevent malaria. In addition, individuals with an unused bed net in the household were more likely to indicate that bed nets are difficult to use, that purchased bed nets are better than freely distributed ones, and that bed nets should only be used during the rainy season. Variations in factors associated with ownership should be acknowledged when constructing messaging and distribution campaigns. Despite reports of bed nets being used for other purposes, those in the home were rarely unused in these communities. Disuse seemed to be related to beliefs that can be addressed through education programmes. As mass distributions continue to take place, additional research is needed to determine if factors associated with LLIN ownership and use change with increasing availability of LLIN.

Indoor tanning and problem behavior.

PubMed

Bagdasarov, Zhanna; Banerjee, Smita; Greene, Kathryn; Campo, Shelly

2008-01-01

The authors examined factors predicting college students' use of tanning beds. Undergraduate students (N = 745) at a large Northeastern university participated in the study by answering a survey measuring tanning behavior and other psychosocial variables, including sensation seeking, self-esteem, tanning image beliefs, and friends' tanning bed use. All 3 systems from problem behavior theory predicted past tanning bed use and intention to use tanning beds. The authors observed a positive association between sensation seeking and intention to use tanning beds. Tanning image beliefs were positively associated with both past tanning behavior and intention to use tanning beds. Interventions focusing on friend and acquaintance social network influences may be more effective than health-risk campaigns in reducing tanning bed use.

Fine bed material in pools of natural gravel bed channels

Treesearch

Thomas E. Lisle; Sue Hilton

1999-01-01

Abstract - Natural gravel bed channels commonly contain a fine mode of sand and fine gravel that fills voids of the bed framework of coarser gravel. If the supply of fine bed material exceeds the storage capacity of framework voids, excess fine material forms surficial patches, which can be voluminous in pools during low flow. Data collected in 34 natural channels in...

76 FR 550 - Second National Bed Bug Summit; Notice of Public Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-05

... ENVIRONMENTAL PROTECTION AGENCY [EPA-HQ-OPP-2009-0190; FRL-8858-4] Second National Bed Bug Summit... planning the second National Bed Bug Summit to be held February 1 and 2, 2011, on the topic of the bed bug resurgence in the United States. The goal of this meeting is to review the current bed bug problem and...

Manual for computing bed load transport using BAGS (Bedload Assessment for Gravel-bed Streams) Software

Treesearch

John Pitlick; Yantao Cui; Peter Wilcock

2009-01-01

This manual provides background information and instructions on the use of a spreadsheet-based program for Bedload Assessment in Gravel-bed Streams (BAGS). The program implements six bed load transport equations developed specifically for gravel-bed rivers. Transport capacities are calculated on the basis of field measurements of channel geometry, reach-average slope,...

Regenerable biocide delivery unit

NASA Technical Reports Server (NTRS)

Sauer, Richard L. (Inventor); Colombo, Gerald V. (Inventor); Jolly, Clifford D. (Inventor)

1993-01-01

A method and apparatus are disclosed for maintaining continuous, long-term microbial control in the water supply for potable, hygiene, and experimental water for space activities, as well as treatment of water supplies on Earth. The water purification is accomplished by introduction of molecular iodine into the water supply to impart a desired iodine residual. The water is passed through an iodinated anion exchange resin bed. The iodine is bound as I-(sub n) at the anion exchange sites and releases I(sub 2) into the water stream flowing through the bed. The concentration of I(sub 2) in the flowing water gradually decreases and, in the prior art, the ion-exchange bed has had to be replaced. In a preferred embodiment, a bed of iodine crystals is provided with connections for flowing water therethrough to produce a concentrated (substantially saturated) aqueous iodine solution which is passed through the iodinated resin bed to recharge the bed with bound iodine. The bed of iodine crystals is connected in parallel with the iodinated resin bed and is activated periodically (e.g., by timer, by measured flow of water, or by iodine residual level) to recharge the bed. Novelty resides in the capability of inexpensively and repeatedly regenerating the ion-exchange bed in situ.

Histamine as an emergent indoor contaminant: Accumulation and persistence in bed bug infested homes.

PubMed

DeVries, Zachary C; Santangelo, Richard G; Barbarin, Alexis M; Schal, Coby

2018-01-01

Histamine is used in bronchial and dermal provocation, but it is rarely considered an environmental risk factor in allergic disease. Because bed bugs defecate large amounts of histamine as a component of their aggregation pheromone, we sought to determine if histamine accumulates in household dust in bed bug infested homes, and the effects of bed bug eradication with spatial heat on histamine levels in dust. We collected dust in homes and analyzed for histamine before, and up to three months after bed bug eradication. Histamine levels in bed bug infested homes were remarkably high (mean = 54.6±18.9 μg/100 mg of sieved household dust) and significantly higher than in control homes not infested with bed bugs (mean < 2.5±1.9 μg/100 mg of sieved household dust). Heat treatments that eradicated the bed bug infestations failed to reduce histamine levels, even three months after treatment. We report a clear association between histamine levels in household dust and bed bug infestations. The high concentrations, persistence, and proximity to humans during sleep suggest that bed bug-produced histamine may represent an emergent contaminant and pose a serious health risk in the indoor environment.

Histamine as an emergent indoor contaminant: Accumulation and persistence in bed bug infested homes

PubMed Central

Santangelo, Richard G.; Barbarin, Alexis M.; Schal, Coby

2018-01-01

Histamine is used in bronchial and dermal provocation, but it is rarely considered an environmental risk factor in allergic disease. Because bed bugs defecate large amounts of histamine as a component of their aggregation pheromone, we sought to determine if histamine accumulates in household dust in bed bug infested homes, and the effects of bed bug eradication with spatial heat on histamine levels in dust. We collected dust in homes and analyzed for histamine before, and up to three months after bed bug eradication. Histamine levels in bed bug infested homes were remarkably high (mean = 54.6±18.9 μg/100 mg of sieved household dust) and significantly higher than in control homes not infested with bed bugs (mean < 2.5±1.9 μg/100 mg of sieved household dust). Heat treatments that eradicated the bed bug infestations failed to reduce histamine levels, even three months after treatment. We report a clear association between histamine levels in household dust and bed bug infestations. The high concentrations, persistence, and proximity to humans during sleep suggest that bed bug-produced histamine may represent an emergent contaminant and pose a serious health risk in the indoor environment. PMID:29432483

Flow resistance under conditions of intense gravel transport

USGS Publications Warehouse

Pitlick, John

1992-01-01

A study of flow resistance was undertaken in a channelized reach of the North Fork Toutle River, downstream of Mount St. Helens, Washington. Hydraulic and sediment transport data were collected in flows with velocities up to 3 m/s and shear stresses up to 7 times the critical value needed for bed load transport. Details of the flow structure as revealed in vertical velocity profiles indicate that weak bed load transport over a plane gravel bed has little effect on flow resistance. The plane gravel bed persists up to stresses ∼3 times critical, at which point, irregular bed forms appear. Bed forms greatly increase flow resistance and cause velocity profiles to become distorted. The latter arises as an effect of flows becoming depth-limited as bed form amplitude increases. At very high rates of bed load transport, an upper stage plane bed appeared. Velocity profiles measured in these flows match the law of the wall closely, with the equivalent roughness being well represented by ks = 3D84 of the bed load. The effects noted here will be important in very large floods or in rivers that are not free to widen, such as those cut into bedrock.

Does Deinstitutionalization Increase Suicide?

PubMed Central

Yoon, Jangho; Bruckner, Tim A

2009-01-01

Objectives (1) To test whether public psychiatric bed reduction may increase suicide rates; (2) to investigate whether the supply of private hospital psychiatric beds—separately for not-for-profit and for-profit—can substitute for public bed reduction without increasing suicides; and (3) to examine whether the level of community mental health resources moderates the relationship between public bed reduction and suicide rates. Methods We examined state-level variation in suicide rates in relation to psychiatric beds and community mental health spending in the United States for the years 1982–1998. We categorize psychiatric beds separately for public, not-for-profit, and for-profit hospitals. Principal Findings Reduced public psychiatric bed supply was found to increase suicide rates. We found no evidence that not-for-profit or for-profit bed supply compensates for public bed reductions. However, greater community mental health spending buffers the adverse effect of public bed reductions on suicide. We estimate that in 2008, an additional decline in public psychiatric hospital beds would raise suicide rates for almost all states. Conclusions Downsizing of public inpatient mental health services may increase suicide rates. Nevertheless, an increase in community mental health funding may be promising. PMID:19500164

Plasma vasopressin and renin activity in women exposed to bed rest and +G/z/ acceleration

NASA Technical Reports Server (NTRS)

Keil, L. C.; Ellis, S.

1976-01-01

To study the effect of prolonged recumbency on plasma vasopressin and renin activity, eight women were subjected to 17 days of absolute bed rest. The tolerance to +3G vertical acceleration of the subjects was tested before and after 14 days of bed rest. From day 2 and through day 17 of bed rest, plasma arginine vasopressin (AVP) levels were reduced 33%. Plasma renin activity (PRA) increased 91% above ambulatory control values from days 10 through 15 of bed rest. When compared to precentrifuge values, exposure to vertical acceleration prior to bed rest provoked a 20-fold rise in mean plasma AVP but resulted in only a slight increase in PRA. After bed rest, acceleration increased plasma AVP 7-fold; however, the magnitude of this increase was less than the post +3G acceleration value obtained prior to bed rest. After bed rest, no significant rise was noted in PRA following +3G acceleration. This study demonstrates that prolonged bed rest leads to a significant rise in the PRA of female subjects, while exposure to positive vertical acceleration provokes a marked rise in plasma AVP.

Predicting fractional bed load transport rates: Application of the Wilcock‐Crowe equations to a regulated gravel bed river

USGS Publications Warehouse

Gaeuman, David; Andrews, E.D.; Krause, Andreas; Smith, Wes

2009-01-01

Bed load samples from four locations in the Trinity River of northern California are analyzed to evaluate the performance of the Wilcock‐Crowe bed load transport equations for predicting fractional bed load transport rates. Bed surface particles become smaller and the fraction of sand on the bed increases with distance downstream from Lewiston Dam. The dimensionless reference shear stress for the mean bed particle size (τ*rm) is largest near the dam, but varies relatively little between the more downstream locations. The relation between τ*rm and the reference shear stresses for other size fractions is constant across all locations. Total bed load transport rates predicted with the Wilcock‐Crowe equations are within a factor of 2 of sampled transport rates for 68% of all samples. The Wilcock‐Crowe equations nonetheless consistently under‐predict the transport of particles larger than 128 mm, frequently by more than an order of magnitude. Accurate prediction of the transport rates of the largest particles is important for models in which the evolution of the surface grain size distribution determines subsequent bed load transport rates. Values of τ*rm estimated from bed load samples are up to 50% larger than those predicted with the Wilcock‐Crowe equations, and sampled bed load transport approximates equal mobility across a wider range of grain sizes than is implied by the equations. Modifications to the Wilcock‐Crowe equation for determining τ*rm and the hiding function used to scale τ*rm to other grain size fractions are proposed to achieve the best fit to observed bed load transport in the Trinity River.

Bed rest attenuates sympathetic and pressor responses to isometric exercise in antigravity leg muscles in humans.

PubMed

Kamiya, Atsunori; Michikami, Daisaku; Shiozawa, Tomoki; Iwase, Satoshi; Hayano, Junichiro; Kawada, Toru; Sunagawa, Kenji; Mano, Tadaaki

2004-05-01

Although spaceflight and bed rest are known to cause muscular atrophy in the antigravity muscles of the legs, the changes in sympathetic and cardiovascular responses to exercises using the atrophied muscles remain unknown. We hypothesized that bed rest would augment sympathetic responses to isometric exercise using antigravity leg muscles in humans. Ten healthy male volunteers were subjected to 14-day 6 degrees head-down bed rest. Before and after bed rest, they performed isometric exercises using leg (plantar flexion) and forearm (handgrip) muscles, followed by 2-min postexercise muscle ischemia (PEMI) that continues to stimulate the muscle metaboreflex. These exercises were sustained to fatigue. We measured muscle sympathetic nerve activity (MSNA) in the contralateral resting leg by microneurography. In both pre- and post-bed-rest exercise tests, exercise intensities were set at 30 and 70% of the maximum voluntary force measured before bed rest. Bed rest attenuated the increase in MSNA in response to fatiguing plantar flexion by approximately 70% at both exercise intensities (both P < 0.05 vs. before bed rest) and reduced the maximal voluntary force of plantar flexion by 15%. In contrast, bed rest did not alter the increase in MSNA response to fatiguing handgrip and had no effects on the maximal voluntary force of handgrip. Although PEMI sustained MSNA activation before bed rest in all trials, bed rest entirely eliminated the PEMI-induced increase in MSNA in leg exercises but partially attenuated it in forearm exercises. These results do not support our hypothesis but indicate that bed rest causes a reduction in isometric exercise-induced sympathetic activation in (probably atrophied) antigravity leg muscles.

[Comparison of PAHs distribution in stabilized sludge by sludge drying bed and reed bed].

PubMed

Cui, Yu-Bo; Sun, Hong-Jie; Ran, Chun-Qiu; Li, Jin-Feng; Xie, Yao

2013-03-01

The difference in the removal efficiencies of polycyclic aromatic hydrocarbons (PAHs) in planted and unplanted sludge drying bed was investigated. Pilot-scale sludge drying bed and reed bed had the same size of 3.0 m x 1.0 m x 1.3 m (L x W x H), and the bed height consisted of a 65 cm media layer and a 65 cm super height. Both beds had a ventilation pipe which was mounted on the drainage pipes. The experiment lasted for three years, and the first two years was the sludge loading period, and the third year was the natural stabilization period. In the first two years, a total thickness of 8.4 m of sludge was loaded and the average sludge loading rate was 41.3 kg x (m2 x a)(-1). After the three-year stabilization, the contents of the sixteen PAHs decreased with time in both the sludge drying bed and the reed bed. The total PAHs contents in the surface, middle and bottom sludge layers in the sludge drying bed were 4.161, 3.543 and 3.118 mg x kg(-1) (DW), corresponding to 26.91%, 37.77% and 45.23% of removal; and the values in the reed bed were 2.722, 1.648 and 1.218 mg x kg(-1) (DW), corresponding to 52.18%, 71.05% and 78.60% of removal. The average PAHs removal in the reed bed was 29.86% higher than that in the sludge drying bed. In the stabilized sludge, the removal of low-molecular-weight PAHs predominated. The results suggested that reed played a positive role in the removal of PAHs.

A computational investigation of the interstitial flow induced by a variably thick blanket of very fine sand covering a coarse sand bed

NASA Astrophysics Data System (ADS)

Bartzke, Gerhard; Huhn, Katrin; Bryan, Karin R.

2017-10-01

Blanketed sediment beds can have different bed mobility characteristics relative to those of beds composed of uniform grain-size distribution. Most of the processes that affect bed mobility act in the direct vicinity of the bed or even within the bed itself. To simulate the general conditions of analogue experiments, a high-resolution three-dimensional numerical `flume tank' model was developed using a coupled finite difference method flow model and a discrete element method particle model. The method was applied to investigate the physical processes within blanketed sediment beds under the influence of varying flow velocities. Four suites of simulations, in which a matrix of uniform large grains (600 μm) was blanketed by variably thick layers of small particles (80 μm; blanket layer thickness approx. 80, 350, 500 and 700 μm), were carried out. All beds were subjected to five predefined flow velocities ( U 1-5=10-30 cm/s). The fluid profiles, relative particle distances and porosity changes within the bed were determined for each configuration. The data show that, as the thickness of the blanket layer increases, increasingly more small particles accumulate in the indentations between the larger particles closest to the surface. This results in decreased porosity and reduced flow into the bed. In addition, with increasing blanket layer thickness, an increasingly larger number of smaller particles are forced into the pore spaces between the larger particles, causing further reduction in porosity. This ultimately causes the interstitial flow, which would normally allow entrainment of particles in the deeper parts of the bed, to decrease to such an extent that the bed is stabilized.

Changes in markers of bone formation and resorption in a bed rest model of weightlessness

NASA Technical Reports Server (NTRS)

Lueken, S. A.; Arnaud, S. B.; Taylor, A. K.; Baylink, D. J.

1993-01-01

To study the mechanism of bone loss in physical unloading, we examined indices of bone formation and bone resorption in the serum and urine of eight healthy men during a 7 day -6 degrees head-down tilt bed rest. Prompt increases in markers of resorption--pyridinoline (PD), deoxypyridinoline (DPD), and hydroxyproline (Hyp)/g creatinine--during the first few days of inactivity were paralleled by tartrate-resistant acid phosphatase (TRAP) with significant increases in all these markers by day 4 of bed rest. An index of formation, skeletal alkaline phosphatase (SALP), did not change during bed rest and showed a moderate 15% increase 1 week after reambulation. In contrast to SALP, serum osteocalcin (OC) began increasing the day preceding the increase in Hyp, remained elevated for the duration of the bed rest, and returned to pre-bed rest values within 5 days of reambulation. Similarly, DPD increased significantly at the onset of bed rest, remained elevated for the duration of bed rest, and returned to pre-bed rest levels upon reambulation. On the other hand, the other three indices of resorption, Hyp, PD, and TRAP, remained elevated for 2 weeks after reambulation. The most sensitive indices of the levels of physical activity proved to be the noncollagenous protein, OC, and the collagen crosslinker, DPD. The bed rest values of both these markers were significantly elevated compared to both the pre-bed rest values and the post-bed rest values. The sequence of changes in the circulating markers of bone metabolism indicated that increases in serum OC are the earliest responses of bone to head-down tilt bed rest.

Using an extreme bony prominence anatomical model to examine the influence of bed sheet materials and bed making methods on the distribution of pressure on the support surface.

PubMed

Iuchi, Terumi; Nakajima, Yukari; Fukuda, Moriyoshi; Matsuo, Junko; Okamoto, Hiroyuki; Sanada, Hiromi; Sugama, Junko

2014-05-01

Bed sheets generate high surface tension across the support surface and increase pressure to the body through a process known as the hammock effect. Using an anatomical model and a loading device characterized by extreme bony prominences, the present study compared pressure distributions on support surfaces across different bed making methods and bed sheet materials to determine the factors that influence pressure distribution. The model was placed on a pressure mapping system (CONFORMat; NITTA Corp., Osaka, Japan), and interface pressure was measured. Bed sheet elasticity and friction between the support surface and the bed sheets were also measured. For maximum interface pressure, the relative values of the following methods were higher than those of the control method, which did not use any bed sheets: cotton sheets with hospital corners (1.28, p = 0.02), polyester with no corners (1.29, p = 0.01), cotton with no corners (1.31, p = 0.003), and fitted polyester sheets (1.35, p = 0.002). Stepwise multiple regression analysis indicated that maximum interface pressure was negatively correlated with bed sheet elasticity (R(2) = 0.74). A statistically significant negative correlation was observed between maximum interface pressure and immersion depth, which was measured using the loading device (r = -0.40 and p = 0.04). We found that several combinations of bed making methods and bed sheet materials induced maximum interface pressures greater than those observed for the control method. Bed sheet materials influenced maximum interface pressure, and bed sheet elasticity was particularly important in reducing maximum interface pressure. Copyright © 2014 Tissue Viability Society. Published by Elsevier Ltd. All rights reserved.

"To sleep, perchance to tweet": in-bed electronic social media use and its associations with insomnia, daytime sleepiness, mood, and sleep duration in adults.

PubMed

Bhat, Sushanth; Pinto-Zipp, Genevieve; Upadhyay, Hinesh; Polos, Peter G

2018-04-01

The use of mobile device-based electronic social media (ESM) in bed is rapidly becoming commonplace, with potentially adverse impacts on sleep and daytime functioning. The purpose of this study was to determine the extent to which in-bed ESM use is associated with insomnia, daytime sleepiness, mood, and sleep duration in adults. This was a cross-sectional observational study conducted among 855 hospital employees and university students (mean age, 43.6years; 85% female) via an online questionnaire. Nearly 70% of participants indulged in in-bed ESM use, with nearly 15% spending an hour or more a night doing so. The degree of in-bed ESM use did not vary by gender, but higher levels of in-bed ESM use were seen in younger and middle-aged than elderly participants. Compared with participants with no in-bed ESM use and controlling for age, gender, and ethnicity, participants with high in-bed ESM use were more likely to have insomnia, anxiety, and short sleep duration on weeknights, but not depression or daytime sleepiness; low in-bed ESM use only increased the likelihood of short sleep duration on weeknights. In-bed ESM use by a bed partner did not have an adverse association with sleep or mood. In-bed ESM use is associated with sleep and mood dysfunction in adults. These findings are of relevance to clinicians, therapists, and the public at large, as they suggest that limitation of in-bed ESM use is a potential interventional strategy in the overall management of sleep hygiene and mental health. Copyright © 2017 National Sleep Foundation. Published by Elsevier Inc. All rights reserved.

Bed Bug Infestations and Control Practices in China: Implications for Fighting the Global Bed Bug Resurgence.

PubMed

Wang, Changlu; Wen, Xiujun

2011-04-11

The bed bug resurgence in North America, Europe, and Australia has elicited interest in investigating the causes of the widespread and increasing infestations and in developing more effective control strategies. In order to extend global perspectives on bed bug management, we reviewed bed bug literature in China by searching five Chinese language electronic databases. We conducted telephone interviews of staff from 77 Health and Epidemic Prevention Stations in six Chinese cities in November 2010. We also conducted telephone interviews of 68 pest control firms in two cities during March 2011. Two species of bed bugs (Cimex lectularius L. and Cimex hemipterus (F.)) are known to occur in China. These were common urban pests before the early1980s. Nationwide "Four-Pest Elimination" campaigns (bed bugs being one of the targeted pests) were implemented in China from 1960 to the early 1980s. These campaigns succeeded in the elimination of bed bug infestations in most communities. Commonly used bed bug control methods included applications of hot water, sealing of bed bug harborages, physical removal, and applications of residual insecticides (mainly organophosphate sprays or dusts). Although international and domestic travel has increased rapidly in China over the past decade (2000-2010), there have only been sporadic new infestations reported in recent years. During 1999-2009, all documented bed bug infestations were found in group living facilities (military dormitories, worker dormitories, and prisons), hotels, or trains. One city (Shenzhen city near Hong Kong) experienced significantly higher number of bed bug infestations. This city is characterized by a high concentration of migratory factory workers. Current bed bug control practices include educating residents, washing, reducing clutter, putting items under the hot sun in summer, and applying insecticides (pyrethroids or organophosphates). There have not been any studies or reports on bed bug insecticide resistance. Difficulties of control were noted in our surveys of dormitories in which crowded living, seasonal worker migration, and financial constraints contributed to control failures. This study supports the following conclusions: (1) the bed bug infestation in China dramatically decreased following the campaigns from 1960 to the early 1980s; (2) In our survey of Health and Epidemics Prevention Stations, no bed bug cases were reported in Beijing and Shanghai for the past 12 months, but complaints were reported in Guangzhou, Lanzhou, Urumqi, and Shenzhen; (3) Current bed bug infestations primarily are reported in crowded living environments or transient environments such as worker dormitories and military dormitories. These findings suggest that community-wide bed bug monitoring and control campaigns are necessary for effective control of bed bug infestations as a societal response.

Bed Bug Infestations and Control Practices in China: Implications for Fighting the Global Bed Bug Resurgence

PubMed Central

Wang, Changlu; Wen, Xiujun

2011-01-01

The bed bug resurgence in North America, Europe, and Australia has elicited interest in investigating the causes of the widespread and increasing infestations and in developing more effective control strategies. In order to extend global perspectives on bed bug management, we reviewed bed bug literature in China by searching five Chinese language electronic databases. We conducted telephone interviews of staff from 77 Health and Epidemic Prevention Stations in six Chinese cities in November 2010. We also conducted telephone interviews of 68 pest control firms in two cities during March 2011. Two species of bed bugs (Cimex lectularius L. and Cimex hemipterus (F.)) are known to occur in China. These were common urban pests before the early1980s. Nationwide “Four-Pest Elimination” campaigns (bed bugs being one of the targeted pests) were implemented in China from 1960 to the early 1980s. These campaigns succeeded in the elimination of bed bug infestations in most communities. Commonly used bed bug control methods included applications of hot water, sealing of bed bug harborages, physical removal, and applications of residual insecticides (mainly organophosphate sprays or dusts). Although international and domestic travel has increased rapidly in China over the past decade (2000–2010), there have only been sporadic new infestations reported in recent years. During 1999–2009, all documented bed bug infestations were found in group living facilities (military dormitories, worker dormitories, and prisons), hotels, or trains. One city (Shenzhen city near Hong Kong) experienced significantly higher number of bed bug infestations. This city is characterized by a high concentration of migratory factory workers. Current bed bug control practices include educating residents, washing, reducing clutter, putting items under the hot sun in summer, and applying insecticides (pyrethroids or organophosphates). There have not been any studies or reports on bed bug insecticide resistance. Difficulties of control were noted in our surveys of dormitories in which crowded living, seasonal worker migration, and financial constraints contributed to control failures. This study supports the following conclusions: (1) the bed bug infestation in China dramatically decreased following the campaigns from 1960 to the early 1980s; (2) In our survey of Health and Epidemics Prevention Stations, no bed bug cases were reported in Beijing and Shanghai for the past 12 months, but complaints were reported in Guangzhou, Lanzhou, Urumqi, and Shenzhen; (3) Current bed bug infestations primarily are reported in crowded living environments or transient environments such as worker dormitories and military dormitories. These findings suggest that community-wide bed bug monitoring and control campaigns are necessary for effective control of bed bug infestations as a societal response. PMID:26467615

Method for in situ gasification of a subterranean coal bed

DOEpatents

Shuck, Lowell Z.

1977-05-31

The method of the present invention relates to providing controlled directional bores in subterranean earth formations, especially coal beds for facilitating in situ gasification operations. Boreholes penetrating the coal beds are interconnected by laser-drilled bores disposed in various arrays at selected angles to the major permeability direction in the coal bed. These laser-drilled bores are enlarged by fracturing prior to the gasification of the coal bed to facilitate the establishing of combustion zones of selected configurations in the coal bed for maximizing the efficiency of the gasification operation.

Phase holdups in three-phase fluidized beds in the presence of disc promoter

DOE Office of Scientific and Technical Information (OSTI.GOV)

Murty, M.S.N.; Ramesh, K.V.; Venkateswarlu, P.

2011-02-15

Three-phase fluidized beds are found to have wide applications in process industries. The present investigation essentially comprises of the studies on gas holdup, liquid holdup and bed porosity in three-phase fluidized beds with coaxially placed disc promoter. Holdup data were obtained from bed expansion and pressure drop measurements. Analysis of the data was done to elucidate the effects of dynamic and geometric parameters on gas holdup, liquid holdup and bed porosity. Data were correlated and useful equations were obtained from empirical modeling. (author)

WTP Pretreatment Facility Potential Design Deficiencies--Sliding Bed and Sliding Bed Erosion Assessment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hansen, E. K.

2015-05-06

This assessment is based on readily available literature and discusses both Newtonian and non-Newtonian slurries with respect to sliding beds and erosion due to sliding beds. This report does not quantify the size of the sliding beds or erosion rates due to sliding beds, but only assesses if they could be present. This assessment addresses process pipelines in the Pretreatment (PT) facility and the high level waste (HLW) transfer lines leaving the PT facility to the HLW vitrification facility concentrate receipt vessel.

Mass and heat transfer in crushed oil shale

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carley, J.F.; Ott, L.L.; Swecker, J.L.

1995-03-01

Studies of heat and mass transfer in packed beds, which disagree substantially in their findings, have nearly all been done with beds of regular particles of uniform size, whereas oil-shale retorting involves particles of diverse irregular shapes and sizes. The authors, in 349 runs, measured mass-transfer rates front naphthalene particles buried in packed beds by passing through air at room temperature. An exact catalog between convection of heat and mass makes it possible to infer heat-transfer coefficients from measured mass-transfer coefficients and fluid properties. Some beds consisted of spheres, naphthalene and inert, of the same, contrasting or distributed sizes. Inmore » some runs, naphthalene spheres were buried in beds of crushed shale, some in narrow screen ranges and others with a wide size range. In others, naphthalene lozenges of different shapes were buried in beds of crushed shale in various bed axis orientations. This technique permits calculation of the mass-transfer coefficient for each active particle in the bed rather than, as in most past studies, for the bed as a whole. The data are analyzed by the traditional correlation of Colburn j{sub D} vs. Reynolds number and by multiple regression of the mass-transfer coefficient on air rate, sizes of active and inert particles, void fraction, and temperature. Principal findings are: local Reynolds number should be based on the active-particle size, not the average for the whole bed; differences between shallow and deep beds are not appreciable; mass transfer is 26% faster for spheres and lozenges buried in shale than in all-sphere beds; orientation of lozenges in shale beds has little or no effect on mass-transfer rate; and for mass or heat transfer in shale beds, log(j{center_dot}{epsilon}) = {minus}0.0747 - 0.6344 log N{sub Re} + 0. 0592 log {sup 2} N{sub Re}.« less

Bed site selection by a subordinate predator: an example with the cougar (Puma concolor) in the Greater Yellowstone Ecosystem.

PubMed

Kusler, Anna; Elbroch, L Mark; Quigley, Howard; Grigione, Melissa

2017-01-01

As technology has improved, our ability to study cryptic animal behavior has increased. Bed site selection is one such example. Among prey species, bed site selection provides thermoregulatory benefits and mitigates predation risk, and may directly influence survival. We conducted research to test whether a subordinate carnivore also selected beds with similar characteristics in an ecosystem supporting a multi-species guild of competing predators. We employed a model comparison approach in which we tested whether cougar ( Puma concolor ) bed site attributes supported the thermoregulatory versus the predator avoidance hypotheses, or exhibited characteristics supporting both hypotheses. Between 2012-2016, we investigated 599 cougar bed sites in the Greater Yellowstone Ecosystem and examined attributes at two scales: the landscape (second-order, n  = 599) and the microsite (fourth order, n  = 140). At the landscape scale, cougars selected bed sites in winter that supported both the thermoregulatory and predator avoidance hypotheses: bed sites were on steeper slopes but at lower elevations, closer to the forest edge, away from sagebrush and meadow habitat types, and on southern, eastern, and western-facing slopes. In the summer, bed attributes supported the predator avoidance hypothesis over the thermoregulation hypothesis: beds were closer to forest edges, away from sagebrush and meadow habitat classes, and on steeper slopes. At the microsite scale, cougar bed attributes in both the winter and summer supported both the predator avoidance and thermoregulatory hypotheses: they selected bed sites with high canopy cover, high vegetative concealment, and in a rugged habitat class characterized by cliff bands and talus fields. We found that just like prey species, a subordinate predator selected bed sites that facilitated both thermoregulatory and anti-predator functions. In conclusion, we believe that measuring bed site attributes may provide a novel means of measuring the use of refugia by subordinate predators, and ultimately provide new insights into the habitat requirements and energetics of subordinate carnivores.

Practical aspects and uncertainty analysis of biological effective dose (BED) regarding its three-dimensional calculation in multiphase radiotherapy treatment plans

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kauweloa, Kevin I., E-mail: Kauweloa@livemail.uthscsa.edu; Gutierrez, Alonso N.; Bergamo, Angelo

2014-07-15

Purpose: There is a growing interest in the radiation oncology community to use the biological effective dose (BED) rather than the physical dose (PD) in treatment plan evaluation and optimization due to its stronger correlation with radiobiological effects. Radiotherapy patients may receive treatments involving a single only phase or multiple phases (e.g., primary and boost). Since most treatment planning systems cannot calculate the analytical BED distribution in multiphase treatments, an approximate multiphase BED expression, which is based on the total physical dose distribution, has been used. The purpose of this paper is to reveal the mathematical properties of the approximatemore » BED formulation, relative to the true BED. Methods: The mathematical properties of the approximate multiphase BED equation are analyzed and evaluated. In order to better understand the accuracy of the approximate multiphase BED equation, the true multiphase BED equation was derived and the mathematical differences between the true and approximate multiphase BED equations were determined. The magnitude of its inaccuracies under common clinical circumstances was also studied. All calculations were performed on a voxel-by-voxel basis using the three-dimensional dose matrices. Results: Results showed that the approximate multiphase BED equation is accurate only when the dose-per-fractions (DPFs) in both the first and second phases are equal, which occur when the dose distribution does not significantly change between the phases. In the case of heterogeneous dose distributions, which significantly vary between the phases, there are fewer occurrences of equal DPFs and hence the inaccuracy of the approximate multiphase BED is greater. These characteristics are usually seen in the dose distributions being delivered to organs at risk rather than to targets. Conclusions: The finding of this study indicates that the true multiphase BED equation should be implemented in the treatment planning systems due to the inconsistent accuracy of the approximate multiphase BED equation in most of the clinical situations.« less

Potential population growth and harmful effects on humans from bed bug populations exposed to different feeding regimes.

PubMed

Pereira, R M; Taylor, A S; Lehnert, M P; Koehler, P G

2013-06-01

Effects of host availability and feeding period on bed bugs, Cimex lectularius (L.) (Hemiptera: Cimicidae), were measured. Population growth and the potential harmful effect of bed bug populations on human hosts were modelled. Bloodmeal sizes were affected by both feeding length and frequency, with >2-fold difference between insects fed daily or weekly. Blood consumption increased >2-fold between bed bugs fed occasionally and often, and 1.5-fold between occasional and daily feeding. Bed bugs fed more often than once a week, potentially every 2-4 days. Egg production was associated with nutrition, being strongly correlated with blood consumption in the previous week. Bed bug populations can grow under different feeding regimes and are hard to control with <80% mortality. Bed bugs can survive and grow even in locations with a limited blood supply, where bed bug persistence may be important for the continual spread of populations. Persistence in non-traditional locations and a potential association with human pathogens increase the health risks of bed bugs. Potential blood loss as a result of a bed bug can have serious consequences because uncontrolled populations can reach harmful levels in 3-8 months. The reproduction potential of bed bug populations suggests serious consequences to human health and the need for efficacious control measures. © 2012 The Royal Entomological Society.

Body dissatisfaction and socio-cultural factors in women with and without BED: their relation with eating psychopathology.

PubMed

Bautista-Díaz, M L; Franco-Paredes, K; Mancilla-Díaz, J M; Alvarez-Rayón, G; López-Aguilar, X; Ocampo Téllez-Girón, T; Soto-González, Y

2012-06-01

The goal of the present study was to assess the role of body dissatisfaction and socio-cultural factors on eating psychopathology in women with Binge Eating Disorder (BED) and women without BED. Seventy obese women consecutively evaluated participated: 35 with BED and 35 without BED who attended for the first time in a weight loss program. All participants completed a battery of questionnaires, including: Body Shape Questionnaire, Questionnaire of Influences on the Aesthetic Body Shape Model, Questionnaire on Eating and Weight Patterns, Three Factor Eating Questionnaire, and they were interviewed with the Interview for the Diagnosis of Eating Disorder-IV. The Body Mass Index, Waist-to-Hip Ratio and Body Fat were calculated. The results showed that 21% of obese women who participated in a weight reduction program met BED criteria. The scores of body dissatisfaction, influences of socio-cultural factors and eating psychopathology were higher in women with BED compared with women without BED. In the same way, significantly stronger correlations were found among influences of socio-cultural factors, specifically, influence of advertisement, social relations and eating psychopathology in women with BED than women without BED. It is concluded that the high body dissatisfaction as well as stronger associations among influence of socio-cultural factors and eating psychopathology could play an important role in women with BED.

Development and Evaluation of a Wide-Bed Former for Vegetable Cultivation in Controlled Tractor Traffic

NASA Astrophysics Data System (ADS)

Dixit, Anoop; Khurana, Rohinish; Verma, Aseem; Singh, Arshdeep; Manes, G. S.

2018-05-01

India is the second largest producer of vegetables in the world. For vegetable cultivation, a good seed bed preparation is an important task which involves 6-10 different operations. To tackle the issue of multiple operations, a prototype of tractor operated wide bed former was developed and evaluated. The machine comprises of a rotary tiller and a bed forming setup. It forms bed of 1000 mm top width which is suitable as per the track width of an average sized tractor in India. The height of the beds formed is 130 mm whereas the top and bottom width of channel formed on both sides of the bed is 330 and 40 mm respectively at soil moisture content of 12.5-16% (db). The forward speed of 2.75 km/h was observed to be suitable for proper bed formation. The average fuel consumption of the machine was 5.9 l/h. The average bulk density of soil before and after the bed formation was 1.46 and 1.63 g/cc respectively. Field capacity of the machine was found to be 0.31 ha/h. The machine resulted in 93.8% labour saving and 80.4% saving in cost of bed preparation as compared to conventional farmer practice. Overall performance of wide-bed former was found to be satisfactory.

Experimental study on the bed shear stress under breaking waves

NASA Astrophysics Data System (ADS)

Hao, Si-yu; Xia, Yun-feng; Xu, Hua

2017-06-01

The object of present study is to investigate the bed shear stress on a slope under regular breaking waves by a novel instrument named Micro-Electro-Mechanical System (MEMS) flexible hot-film shear stress sensor. The sensors were calibrated before application, and then a wave flume experiment was conducted to study the bed shear stress for the case of regular waves spilling and plunging on a 1:15 smooth PVC slope. The experiment shows that the sensor is feasible for the measurement of the bed shear stress under breaking waves. For regular incident waves, the bed shear stress is mainly periodic in both outside and inside the breaking point. The fluctuations of the bed shear stress increase significantly after waves breaking due to the turbulence and vortexes generated by breaking waves. For plunging breaker, the extreme value of the mean maximum bed shear stress appears after the plunging point, and the more violent the wave breaks, the more dramatic increase of the maximum bed shear stress will occur. For spilling breaker, the increase of the maximum bed shear stress along the slope is gradual compared with the plunging breaker. At last, an empirical equation about the relationship between the maximum bed shear stress and the surf similarity parameter is given, which can be used to estimate the maximum bed shear stress under breaking waves in practice.

Pulse enhanced fluidized bed combustion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mueller, B.

1996-12-31

Information is outlined on pulse enhanced fluidized bed combustion. The following topics are discussed: what is pulse enhanced fluidized bed combustion?; pulse combustors; pulsed atmospheric fluidized bed combustor (PAFBC); advantages of PAFBC; performance advantages; PAFBC facts; and PAFBC contact points.

Bed bug aggregation pheromone finally identified.

PubMed

Gries, Regine; Britton, Robert; Holmes, Michael; Zhai, Huimin; Draper, Jason; Gries, Gerhard

2015-01-19

Bed bugs have become a global epidemic and current detection tools are poorly suited for routine surveillance. Despite intense research on bed bug aggregation behavior and the aggregation pheromone, which could be used as a chemical lure, the complete composition of this pheromone has thus far proven elusive. Here, we report that the bed bug aggregation pheromone comprises five volatile components (dimethyl disulfide, dimethyl trisulfide, (E)-2-hexenal, (E)-2-octenal, 2-hexanone), which attract bed bugs to safe shelters, and one less-volatile component (histamine), which causes their arrestment upon contact. In infested premises, a blend of all six components is highly effective at luring bed bugs into traps. The trapping of juvenile and adult bed bugs, with or without recent blood meals, provides strong evidence that this unique pheromone bait could become an effective and inexpensive tool for bed bug detection and potentially their control. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Effect of bed rest and exercise on body balance

NASA Technical Reports Server (NTRS)

Haines, R. F.

1974-01-01

A battery of 11 body balance tests was administered to 7 men before and after 14 days of bedrest. Seven men who had not undergone bed rest served as controls. During bed rest, each subject underwent daily either isotonic, isometric, or no leg exercise. The results showed that, for the bed-rested no exercise, isotonic exercise, and isometric exercise groups, 2 weeks of bed rest produces significant body balance decrements on 3, 4, and 5 of the 11 tests, respectively. Daily leg exercise did not prevent the debilitating effects of bed rest on body balance. After bed rest, balance skill was relearned rapidly so that in most tests, performance had reached prebed-rest levels by the third recovery day. These data suggest that balance impairment is not due to loss of muscular strength in the legs but, perhaps, to a bed-rest-related change in the neurally coded information to postural control centers.

The role of coherence of mind and reflective functioning in understanding binge-eating disorder and co-morbid overweight.

PubMed

Maxwell, Hilary; Tasca, Giorgio A; Grenon, Renee; Faye, Megan; Ritchie, Kerri; Bissada, Hany; Balfour, Louise

2017-08-01

Coherence of mind and reflective functioning may impact negative affect and interpersonal functioning over and above the effects of symptoms of depression and interpersonal problems that contribute to symptoms of binge-eating disorder (BED) and overweight/obesity. Matched samples of overweight women with BED and overweight and normal weight women without BED completed the Adult Attachment Interview, a measure of depressive symptoms, and a measure of interpersonal problems. Greater symptoms of depression distinguished women with BED from the matched comparison samples. Greater interpersonal problems differentiated women with BED from overweight women without BED. Coherence of Mind scores did not differentiate the samples. However, lower Reflective Functioning scores did distinguish both women with BED and overweight women without BED from normal weight women. Lower reflective functioning may lead to binge eating independent of depressive symptoms and interpersonal problems.

Virtual Design of a 4-Bed Molecular Sieve for Exploration

NASA Technical Reports Server (NTRS)

Giesy, Timothy J.; Coker, Robert F.; O'Connor, Brian F.; Knox, James C.

2017-01-01

Simulations of six new 4-Bed Molecular Sieve configurations have been performed using a COMSOL (COMSOL Multiphysics - commercial software) model. The preliminary results show that reductions in desiccant bed size and sorbent bed size when compared to the International Space Station configuration are feasible while still yielding a process that handles at least 4.0 kilograms a day CO2. The results also show that changes to the CO2 sorbent are likewise feasible. Decreasing the bed sizes was found to have very little negative effect on the adsorption process; breakthrough of CO2 in the sorbent bed was observed for two of the configurations, but a small degree of CO2 breakthrough is acceptable, and water breakthrough in the desiccant beds was not observed. Both configurations for which CO2 breakthrough was observed still yield relatively high CO2 efficiency, and future investigations will focus on bed size in order to find the optimum configuration.

Virtual Design of a 4-Bed Molecular Sieve for Exploration

NASA Technical Reports Server (NTRS)

Giesy, Timothy J.; Coker, Robert F.; O'Connor, Brian F.; Knox, James C.

2017-01-01

Simulations of six new 4-Bed Molecular Sieve configurations have been performed using a COMSOL model. The preliminary results show that reductions in desiccant bed size and sorbent bed size when compared to the International Space Station configuration are feasible while still yielding a process that handles at least 4.0 kg/day CO2. The results also show that changes to the CO2 sorbent are likewise feasible. Decreasing the bed sizes was found to have very little negative effect on the adsorption process; breakthrough of CO2 in the sorbent bed was observed for two of the configurations, but water breakthrough in the desiccant beds was not observed. Nevertheless, both configurations for which CO2 breakthrough was observed still yield relatively high CO2 efficiency, and future investigations will focus on bed size in order to find the optimum configuration.

Loneliness mediates the relationship between emotion dysregulation and bulimia nervosa/binge eating disorder psychopathology in a clinical sample

PubMed Central

Christensen, Kara A.; Fettich, Karla C.; Weissman, Jessica; Berona, Johnny; Chen, Eunice Y.

2017-01-01

Emotion dysregulation has been linked to binge eating disorder (BED) and bulimia nervosa (BN) although the mechanisms by which it affects BN/BED psychopathology are unclear. This study tested loneliness as a mediator between emotion dysregulation and BN/BED psychopathology. A treatment-seeking sample of 107 women with BN or BED was assessed for loneliness (UCLA Loneliness Scale), emotion dysregulation (Difficulties in Emotion Regulation Scale), and BN/BED psychopathology (Eating Disorder Examination) before treatment. Hierarchical linear regressions and bootstrapping mediation models were run. Greater overall emotion dysregulation was associated with greater BN/BED psychopathology, mediated by loneliness (95 % CI 0.03, 0.09). Emotion dysregulation, however, did not mediate between loneliness and BN/BED psychopathology (95 % CI −0.01, 0.01). Targeting loneliness may effectively treat emotional aspects of BN/BED in women. PMID:24235091

Variability of bed mobility in natural, gravel-bed channels and adjustments to sediment load at local and reach scales

Treesearch

Thomas E. Lisle; Jonathan M. Nelson; John Pitlick; Mary Ann Madej; Brent L. Barkett

2000-01-01

Abstract - Local variations in boundary shear stress acting on bed-surface particles control patterns of bed load transport and channel evolution during varying stream discharges. At the reach scale a channel adjusts to imposed water and sediment supply through mutual interactions among channel form, local grain size, and local flow dynamics that govern bed mobility...

Odorous volatile organic compounds, Escherichia coli, and nutrient concentrations when kiln-dried pine chips and corn stover bedding are used in beef bedded manure packs

USDA-ARS?s Scientific Manuscript database

Pine (Pinus spp.) bedding has been shown to lower the concentration of odorous volatile organic compounds (VOCs) and pathogenic bacteria compared with corn (Zea mays L.) stover bedding, but availability and cost limit the use of pine bedding in cattle confinement facilities. The objectives of this s...

[The structural functional analysis of beds stock of curative preventive organizations of the state public health system of the Russian Federation].

PubMed

Schepin, V O

2014-01-01

The article presents the results of comprehensive scientific analysis of size and structure of beds stock of medical curative preventive organizations of state and municipal health care systems of the Russian Federation. The issues of beds support of population on national, federal okrugs and federation subjects' levels including differentiation on different medical specialties are considered. The main indicators of functioning of hospitals, per capita consumption of hospital medical care and territorial characteristics and differences of these indicators are analyzed In conditions of on-going decrease of size of beds stock and amount of medical care in hospitals and against the background of stability of main indicators of beds use the expressed but not always objectively conditioned differences continue to be present concerning both population support with beds stock and indicators of consumption of medical care in hospitals. All these occurrences undoubtedly impact accessibility of this type of medical care to population and its resource capacity for the government. In 2012, beds support of population decreased from 85.7 to 84.1 beds per 10 000 of population. The value of indicator in federal subjects differs up to 2.9 times. In the structure of beds stock are prevailing specialized beds or groups of beds on such medical specialties as psychiatry, surgery, obstetrics and gynecology and therapy. The per capita use of medical care in hospitals decreased up to 2.609 beds-per-day that is 6.2% lower than standard value from the program of state guarantees of free-of-charge medical care support of citizen. The end values of indicator in federal subjects differ in 2.7 times. In federal subjects indicators of mean number of work of bed per year differ up to 1.2 times, of mean duration of treatment--up to 1.6 times, turn-over of bed--up to 1.6 times, hospital lethality--up to 5.9 times. The results of study confirm necessity of structural functional optimization of national beds stock and development of interaction between hospitals and out-patient services.

A qualitative study on caretakers' perceived need of bed-nets after reduced malaria transmission in Zanzibar, Tanzania

PubMed Central

2012-01-01

Background The elimination of malaria in Zanzibar is highly dependent on sustained effective coverage of bed-nets to avoid malaria resurgence. The Health Belief Model (HBM) framework was used to explore the perceptions of malaria and bed-net use after a noticeable reduction in malaria incidence. Methods Nineteen in-depth interviews were conducted with female and male caretakers of children under five in North A district, Zanzibar. Deductive content analysis was used to identify meaning units that were condensed, coded and assigned to pre-determined elements of the HBM. Results Awareness of malaria among caretakers was high but the illness was now seen as easily curable and uncommon. In addition to the perceived advantage of providing protection against malaria, bed-nets were also thought to be useful for avoiding mosquito nuisance, especially during the rainy season when the malaria and mosquito burden is high. The discomfort of sleeping under a net during the hot season was the main barrier that interrupted consistent bed-net usage. The main cue to using a bed-net was high mosquito density, and children were prioritized when it came to bed-net usage. Caretakers had high perceived self-efficacy and did not find it difficult to use bed-nets. Indoor Residual Spraying (IRS), which was recognized as an additional means of mosquito prevention, was not identified as an alternative for bed-nets. A barrier to net ownership was the increasingly high cost of bed-nets. Conclusions Despite the reduction in malaria incidence and the resulting low malaria risk perceptions among caretakers, the benefit of bed-nets as the most proficient protection against mosquito bites upholds their use. This, in combination with the perceived high self-efficacy of caretakers, supports bed-net usage, while seasonality interrupts consistent use. High effective coverage of bed-nets could be further improved by reinforcing the benefits of bed-nets, addressing the seasonal heat barrier by using nets with larger mesh sizes and ensuring high bed-net ownership rates through sustainable and affordable delivery mechanisms. PMID:22863188

An adjusted bed net coverage indicator with estimations for 23 African countries

PubMed Central

2013-01-01

Background Many studies have assessed the level of bed net coverage in populations at risk of malaria infection. These revealed large variations in bed net use across countries, regions and social strata. Such studies are often aimed at identifying populations with low access to bed nets that should be prioritized in future interventions. However, often spatial differences in malaria endemicity are not taken into account. By ignoring variability in malaria endemicity, these studies prioritize populations with little access to bed nets, even if these happen to live in low endemicity areas. Conversely, populations living in regions with high malaria endemicity will receive a lower priority once a seizable proportion is protected by bed nets. Adequately assigning priorities requires accounting for both the current level of bed net coverage and the local malaria endemicity. Indeed, as shown here for 23 African countries, there is no correlation between the level of bed net coverage and the level of malaria endemicity in a region. Therefore, the need for future interventions can not be assessed based on current bed net coverage alone. This paper proposes the Adjusted Bed net Coverage (ABC) statistic as a measure taking into account both local malaria endemicity and the level of bed net coverage. The measure allows setting priorities for future interventions taking into account both local malaria endemicity and bed net coverage. Methods A mathematical formulation of the ABC as a weighted difference of bed net coverage and malaria endemicity is presented. The formulation is parameterized based on a model of malaria epidemiology (Smith et al. Trends Parasitol 25:511-516, 2009). By parameterizing the ABC based on this model, the ABC as used in this paper is proxy for the steady-state malaria burden given the current level of bed net coverage. Data on the bed net coverage in under five year olds and malaria endemicity in 23 Sub-Saharan countries is used to show that the ABC prioritizes different populations than the level of bed net coverage by itself. Data from the following countries was used: Angola, Burkina Faso, Burundi, Cameroon, Congo Democratic Republic, Ethiopia, Ghana, Guinea, Kenya, Liberia, Madagascar, Malawi, Mali, Mozambique, Namibia, Nigeria, Rwanda, Senegal, Sierra Leone, Tanzania, Uganda, Zambia and Zimbabwe. The priority order given by the ABC and the bed net coverage are compared at the countries’ level, the first level administrative divisions and for five different wealth quintiles. Results Both at national level and at the level of the administrative divisions the ABC suggests a different priority order for selecting countries and divisions for future interventions. When taking into account malaria endemicity, measures assessing equality in access to bed nets across wealth quintiles, such as slopes of inequality, are prone to change. This suggests that when assessing inequality in access to bed nets one should take into account the local malaria endemicity for populations from different wealth quintiles. Conclusion Accounting for malaria endemicity highlights different countries, regions and socio-economic strata for future intervention than the bed net coverage by itself. Therefore, care should be taken to factor out any effects of local malaria endemicity in assessing bed net coverage and in prioritizing populations for further scale-up of bed net coverage. The ABC is proposed as a simple means to do this that is derived from an existing model of malaria epidemiology. PMID:24359227

Comparison of Three Bed Bug Management Strategies in a Low-Income Apartment Building.

PubMed

Wang, Changlu; Saltzmann, Kurt; Bennett, Gary; Gibb, Timothy

2012-04-02

Bed bug (Cimex lectularius L.) infestations are currently controlled by a variety of non-chemical and chemical methods. There have been few studies on the comparative effectiveness of these control techniques. We evaluated three bed bug management strategies in an apartment building: (1) non-chemical methods only (n = 9); (2) insecticides only (n = 6); and (3) integrated pest management including both non-chemical methods and insecticides (n = 9). The apartments were one-bedroom units occupied by seniors or people with disabilities. Bed bug numbers in each apartment were determined by visual inspection and/or installing intercepting devices under bed and sofa legs. The median (min, max) bed bug counts in the non-chemical methods only, insecticides only, and integrated pest management (IPM) treatment were: 4 (1, 57), 19 (1, 250), and 14 (1, 219), respectively prior to the treatments. The apartments were retreated if found necessary during biweekly to monthly inspections. After 10 weeks, bed bugs were found to be eliminated from 67, 33, and 44% of the apartments in the three treatment groups, respectively. The final (after 10 weeks) median (min, max) bed bug counts in the non-chemical methods only, insecticides only, and IPM treatment were: 0 (0, 134), 11.5 (0, 58), and 1 (0, 38), respectively. There were no significant differences in the speed of bed bug count reduction or the final bed bug counts. Lack of resident cooperation partially contributed to the failure in eliminating bed bugs from some of the apartments. Results of this study suggest that non-chemical methods can effectively eliminate bed bugs in lightly infested apartments.

Tracking bed bugs (Cimex lectularius): a study of the effect of physiological and extrinsic factors on the response to bed bug-derived volatiles.

PubMed

Weeks, E N I; Logan, J G; Birkett, M A; Pickett, J A; Cameron, M M

2013-02-01

The common bed bug, Cimex lectularius, feeds on the blood of mammal and bird hosts, and is a pest of global importance. Semiochemicals are chemicals involved in animal communication that may affect behaviour and/or physiology. Attractive semiochemicals that play a role in mediating bed bug behaviour could be exploited for the development of a highly effective novel monitoring device. Tracking software was used to record the response of bed bugs to volatiles from paper previously exposed to conspecific bugs in a still-air olfactometer illuminated by infrared lights, through a variety of activity variables. The effect of time of day as an extrinsic factor, and sex, stage, mating status and nutritional status as physiological factors on the response of bed bugs to the volatiles was examined. Bed bugs of both sexes and all stages responded to the volatiles from bed bug-exposed papers, showing significant attraction and orientation towards the volatile source whether they were starved or engorged. Confirmation that the physiological factors examined do not affect the response of bed bugs to the volatiles from bed bug-exposed papers provides evidence that these bed bug-derived volatiles contain aggregation cues, as semiochemicals that promote aggregation should by definition be detected by both sexes and all life stages. A device baited with such semiochemicals could play a major role in limiting the impact of the current bed bug resurgence by enabling timely detection of infestations, along with quantitative evaluation of control and effective surveillance of the geographical distribution of the pest species.

Channel widening due to urbanization and a major flood can alter bed particle organization and bed stability in an urban boulder-bed channel

NASA Astrophysics Data System (ADS)

Prestegaard, K. L.; Behrns, K.; Blanchet, Z.; Hankin, E.

2007-12-01

The Anacostia River is a tributary of the Potomac River north of Washington D.C. that has become progressively more urbanized in the past 50 years. Bankfull discharge and bankfull width in the Anacostia have increased by 3- 4x in the past 50 years. Nearby watersheds of similar size and geology, but without significant urbanization, contain threshold gravel-bed streams. The Anacostia, however, is not a threshold channel; it exhibits break-up of boulder-bed channels in upstream reaches and significant gravel bar formation in downstream reaches. These gravel bars have grown and migrated considerably in the past 10-15 years, contributing significantly to local channel widening that can be twice that of adjacent reaches. The purpose of this study is to determine bedload transport rates and grain size distributions and their relationship to discharge, bed organization and sediment supply. Bed mobility data come from both bedload transport measurements and measurements of channel bed changes. Channel bed changes were obtained from a) repeated channel cross section surveys, b) surface and subsurface size distributions, and c) bed particle organization measurements (measurements of location of particles within reaches). These measurements were made prior to and after the floods of 2006, which equalled the largest floods on record for most parts of the Anacostia River. In some boulder bed reaches, boulders were removed from the center of the channel and deposited along and on the channel banks. The mid-channel boulders were replaced by sheets of gravel and cobbles, significantly altering the bed mobility of the channels.

A Controlled Evaluation of the Distress Criterion for Binge Eating Disorder

PubMed Central

Grilo, Carlos M.; White, Marney A.

2012-01-01

Objective Research has examined various aspects of the validity of the research criteria for binge eating disorder (BED) but has yet to evaluate the utility of criterion C “marked distress about binge eating.” This study examined the significance of the marked distress criterion for BED using two complementary comparisons groups. Method A total of 1075 community volunteers completed a battery of self-report instruments as part of an internet study. Analyses compared body mass index (BMI), eating-disorder psychopathology, and depressive levels in four groups: 97 participants with BED except for the distress criterion (BED-ND), 221 participants with BED including the distress criterion (BED), 79 participants with bulimia nervosa (BN), and 489 obese participants without binge-eating or purging (NBPO). Parallel analyses compared these study groups using the broadened frequency criterion (i.e., once-weekly for binge/purge behaviors) proposed for DSM-5 and the DSM-IV twice-weekly frequency criterion. Results The BED group had significantly greater eating-disorder psychopathology and depressive levels than the BED-ND group. The BED group, but not the BED-ND group, had significantly greater eating-disorder psychopathology than the NBPO comparison group. The BN group had significantly greater eating-disorder psychopathology and depressive levels than all three other groups. The group differences existed even after controlling for depression levels, BMI, and demographic variables, although some differences between the BN and BED groups were attenuated when controlling for depression levels. Conclusions These findings provide support for the validity of the “marked distress” criterion for the diagnosis of BED. PMID:21707133

Experimental study of the effect of grain sizes in a bimodal mixture on bed slope, bed texture, and the transition to washload

NASA Astrophysics Data System (ADS)

Hill, Kimberly M.; Gaffney, John; Baumgardner, Sarah; Wilcock, Peter; Paola, Chris

2017-01-01

When fine sediment is added to a coarse-grained system, the mobility and composition of the bed can change dramatically. We conducted a series of flume experiments to determine how the size of fine particles introduced to an active gravel bed influences the mobility and composition of the bed. We initiated our experiments using a constant water discharge and feed rate of gravel. After the system reached steady state, we doubled the feed rate by supplying a second sediment of equal or lesser size, creating size ratios from 1:1 to 1:150. As we decreased the relative size of the fine particles, the system transitioned among three regimes: (1) For particle size ratios close to one, the bed slope increased to transport the additional load of similar-sized particles. The bed surface remained planar and unchanged. (2) For intermediate particle size ratios, the bed slope decreased with the additional fines. The bed surface became patchy with regions of fine and coarse grains. (3) For the largest particle size ratios (the smallest fines), the bed slope remained relatively unchanged. The subsurface became clogged with fine sediment, but fine particles were not present in the surface layer. This third regime constitutes washload, defined by those fractions that do not affect bed-material transport conditions. Our results indicate washload should be defined in terms of three conditions: small grain size relative to that of the bed material, full suspension based on the Rouse number, and a small rate of fine sediment supply relative to transport capacity.

Pilot study of the prevalence of binge eating disorder in non-alcoholic fatty liver disease patients.

PubMed

Zhang, Jinyu; Abbasi, Omair; Malevanchik, Lev; Mohan, Neena; Denicola, Richard; Tarangelo, Nicholas; Marzio, Dina Halegoua-De

2017-01-01

Non-alcoholic fatty liver disease (NAFLD) is the most common liver disease in the United States. Binge eating disorder (BED) is the most common form of eating disorder. NAFLD and BED have similar risk factors, including obesity, insulin resistance, and metabolic syndrome. The aim of our study was to examine prevalence of BED in NAFLD patients. We administered the Binge Eating Scale (BES), a questionnaire validated to screen for BED, to NAFLD patients at our Fatty Liver Center. Demographics were retrieved retrospectively from our electronic medical record. Of the total 95 NAFLD patients screened, 22 (23.1%) had binge eating tendencies; 6 of the 22 (6.3%) scored 27 or more points, suggestive of severe binge eating. Patient demographics included 59 females and 36 males (14 females and 8 males positive for BED). Liver disease severity and of metabolic syndrome presence were similar in both groups: 45 patients had steatosis, 25 steatohepatitis, and 24 cirrhosis, of which 10 steatosis, 5 steatohepatitis, and 7 cirrhosis patients screened positive for BED. Of the NAFLD patients with BED, 50.0% had insulin resistance, 68.2% hypertension, and 50.0% hyperlipidemia, whereas among non-BED NAFLD patients 58.9% had insulin resistance, 63.0% hypertension, and 67.1% hyperlipidemia. This pilot study suggests that BED may have a higher prevalence among NAFLD patients than in the general population. Based on these preliminary results, further study into the prevalence of BED is recommended. More data is need to identify effects of BED on the progression of NAFLD and role of BED treatment.

Bed material transport in the Virgin River, Utah

USGS Publications Warehouse

Andrews, E.D.

2000-01-01

Detailed information concerning the rate and particle size distribution of bed material transport by streamflows can be very difficult and expensive to obtain, especially where peak streamflows are brief and bed material is poorly sorted, including some very large boulders. Such streams, however, are common in steep, arid watersheds. Any computational approach must consider that (1) only the smaller particle sizes present on the streambed move even during large floods and (2) the largest bed particles exert a significant form drag on the flow. Conventional methods that rely on a single particle size to estimate the skin friction shear stress acting on the mobile fraction of the bed material perform poorly. Instead, for this study, the skin friction shear stress was calculated for the observed range of streamflows by calculating the form drag exerted on the reach‐averaged flow field by all particle sizes. Suspended and bed load transported rates computed from reach‐averaged skin friction shear stress are in excellent agreement with measured transport rates. The computed mean annual bed material load, including both bed load and suspended load, of the East Fork Virgin River for the water years 1992‐1996 was approximately 1.3×10 5 t. A large portion of the bed material load consists of sand‐sized particles, 0.062–1.0 mm in diameter, that are transported in suspension. Such particles, however, constituted only 10% of the surface bed material and less than 25% of the subsurface bed material. The mean annual quantity of bed load transported was 1060 t/yr with a median size of 15 mm.

Tidal asymmetry and variability of bed shear stress and sediment bed flux at a site in San Francisco Bay, USA

USGS Publications Warehouse

Brennan, Matthew L.; Schoellhamer, David H.; Burau, Jon R.; Monismith, Stephen G.; Winterwerp, J.C.; Kranenburg, C.

2002-01-01

The relationship between sediment bed flux and bed shear stress during a pair of field experiments in a partially stratified estuary is examined in this paper. Time series of flow velocity, vertical density profiles, and suspended sediment concentration were measured continuously throughout the water column and intensely within 1 meter of the bed. These time series were analyzed to determine bed shear stress, vertical turbulent sediment flux, and mass of sediment suspended in the water column. Resuspension, as inferred from near-bed measurements of vertical turbulent sediment flux, was flood dominant, in accordance with the flood-dominant bed shear stress. Bathymetry-induced residual flow, gravitational circulation, and ebb tide salinity stratification contributed to the flood dominance. In addition to this flow-induced asymmetry, the erodibility of the sediment appears to increase during the first 2 hours of flood tide. Tidal asymmetry in bed shear stress and erodibility help explain an estuarine turbidity maximum that is present during flood tide but absent during ebb tide. Because horizontal advection was insignificant during most of the observation periods, the change in bed mass can be estimated from changes in the total suspended sediment mass. The square wave shape of the bed mass time series indicates that suspended sediment rapidly deposited in an unconsolidated or concentrated benthic suspension layer at slack tides and instantly resuspended when the shear stress became sufficiently large during a subsequent tide. The variability of bed mass associated with the spring/neap cycle (about 60 mg/cm2) is similar to that associated with the semidiurnal tidal cycle.

Hospital output forecasts and the cost of empty hospital beds.

PubMed Central

Pauly, M V; Wilson, P

1986-01-01

This article investigates the cost incurred when hospitals have different levels of beds to treat a given number of patients. The cost of hospital care is affected by both the forecasted level of admissions and the actual number of admissions. When the relationship between forecasted and actual admissions is held constant, it is found that an empty hospital bed at a typical hospital in Michigan has a relatively low cost, about 13 percent or less of the cost of an occupied bed. However, empty beds in large hospitals do add significantly to cost. If hospital beds are closed, whether by closing beds at hospitals which remain in business or by closing entire hospitals, cost savings are estimated to be small. PMID:3759473

76 FR 19914 - Safety Standard for Portable Bed Rails: Notice of Proposed Rulemaking

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-11

... constructed primarily of nonrigid materials, such as fabric or foam. An ``inflatable bed rail'' is defined as..., such as fabric or foam; Inflatable bed rail is a portable bed rail constructed primarily of nonrigid...

Introduction to Bed Bugs

EPA Pesticide Factsheets

The common bed bug (Cimex lectularius) is a pest – feeding on blood, causing itchy bites and generally irritating their human hosts. EPA and other agencies all consider bed bugs a public health pest, but bed bugs are not known to transmit disease.

Peering inside the granular bed: illuminating feedbacks between bed-load transport and bed-structure evolution

NASA Astrophysics Data System (ADS)

Houssais, M.; Jerolmack, D. J.; Martin, R. L.

2013-12-01

The threshold of motion is perhaps the most important quantity to determine for understanding rates of bed load transport, however it is a moving target. Decades of research show that it changes in space and in time within a river, and is highly variable among different systems; however, these differences are not mechanistically understood. Recent researchers have proposed that the critical Shields stress is strongly dependent on the local configuration of the sediment bed [Frey and Church, 2011]. Critical Shields stress has been observed to change following sediment-transporting flood events in natural rivers [e.g., Turowski et al., 2011], while small-scale laboratory experiments have produced declining bed load transport rates associated with slow bed compaction [Charru et al., 2004]. However, no direct measurements have been made of the evolving bed structure under bed load transport, so the connection between granular controls and the threshold of motion remains uncertain. A perspective we adopt is that granular effects determine the critical Shields stress, while the fluid supplies a distribution of driving stresses. In order to isolate the granular effect, we undertake laminar bed load transport experiments using plastic beads sheared by a viscous oil in a small, annular flume. The fluid and beads are refractive index matched, and the fluid impregnated with a fluorescing powder. When illuminated with a planar laser sheet, we are able to image slices of the granular bed while also tracking the overlying sediment transport. We present the first results showing how bed load transport influences granular packing, and how changes in packing influence the threshold of motion to feed back on bed load transport rates. This effect may account for much of the variability observed in the threshold of motion in natural streams, and by extension offers a plausible explanation for hysteresis in bed load transport rates observed during floods. Charru, F., H. Mouilleron, and O. Eiff, Erosion and deposition of particles on a bed sheared by a viscous flow, Journal of Fluid Mech., 519, 55-80, 2004 Frey, P. and Church, M. (2011), Bedload: a granular phenomenon. Earth Surf. Process. Landforms, 36: 58-69. doi: 10.1002/esp.2103 Turowski, J. M., A. Badoux, and D. Rickenmann (2011), Start and end of bedload transport in gravel-bed streams, Geophys. Res. Lett., 38, L04401, doi:10.1029/2010GL046558.

Effects of bedding systems selected by manual muscle testing on sleep and sleep-related respiratory disturbances.

PubMed

Tsai, Ling-Ling; Liu, Hau-Min

2008-03-01

In this study, we investigated the feasibility of applying manual muscle testing (MMT) for bedding selection and examined the bedding effect on sleep. Four lay testers with limited training in MMT performed muscle tests for the selection of the bedding systems from five different mattresses and eight different pillows for 14 participants with mild sleep-related respiratory disturbances. For each participant individually, two bedding systems-one inducing stronger muscle forces and the other inducing weaker forces-were selected. The tester-participant pairs showed 85% and 100% agreement, respectively, for the selection of mattresses and pillows that induced the strongest muscle forces. The firmness of the mattress and the height of the pillow were significantly correlated with the body weight and body mass index of the participants for the selected strong bedding system but not for the weak bedding system. Finally, differences were observed between the strong and the weak bedding systems with regard to sleep-related respiratory disturbances and the percentage of slow-wave sleep. It was concluded that MMT can be performed by inexperienced testers for the selection of bedding systems.

Grouped comparisons of sleep quality for new and personal bedding systems.

PubMed

Jacobson, Bert H; Wallace, Tia J; Smith, Doug B; Kolb, Tanner

2008-03-01

The purpose of this study was to compare sleep comfort and quality between personal and new bedding systems. A convenience sample (women, n=33; men, n=29) with no clinical history of disturbed sleep participated in the study. Subjects recorded back and shoulder pain, sleep quality, comfort, and efficiency for 28 days each in their personal beds (pre) and in new medium-firm bedding systems (post). Repeated measures ANOVAs revealed significant improvement between pre- and post-test means for all dependent variables. Furthermore, reduction of pain and stiffness and improvement of sleep comfort and quality became more prominent over time. No significant differences were found for the groupings of age, weight, height, or body mass index. It was found that for the cheapest category of beds, lower back pain was significantly (p<0.01) more prominent than for the medium and higher priced beds. Average bed age was 9.5yrs. It was concluded that new bedding systems can significantly improve selected sleep variables and that continuous sleep quality may be dependent on timely replacement of bedding systems.

Water column and bed-sediment core samples collected from Brownlee Reservoir near Oxbow, Oregon, 2012

USGS Publications Warehouse

Fosness, Ryan L.; Naymik, Jesse; Hopkins, Candice B.; DeWild, John F.

2013-01-01

The U.S. Geological Survey, in cooperation with Idaho Power Company, collected water-column and bed-sediment core samples from eight sites in Brownlee Reservoir near Oxbow, Oregon, during May 5–7, 2012. Water-column and bed-sediment core samples were collected at each of the eight sites and analyzed for total mercury and methylmercury. Additional bed-sediment core samples, collected from three of the eight sites, were analyzed for pesticides and other organic compounds, trace metals, and physical characteristics, such as particle size. Total mercury and methylmercury were detected in each of the water column and bed-sediment core samples. Only 17 of the 417 unique pesticide and organic compounds were detected in bed-sediment core samples. Concentrations of most organic wastewater compounds detected in bed sediment were less than the reporting level. Trace metals detected were greater than the reporting level in all the bed-sediment core samples submitted for analysis. The particle size distribution of bed-sediment core samples was predominantly clay mixed with silt.

The development of test beds to support the definition and evolution of the Space Station Freedom power system

NASA Technical Reports Server (NTRS)

Soeder, James F.; Frye, Robert J.; Phillips, Rudy L.

1991-01-01

Since the beginning of the Space Station Freedom Program (SSFP), the Lewis Research Center (LeRC) and the Rocketdyne Division of Rockwell International have had extensive efforts underway to develop test beds to support the definition of the detailed electrical power system design. Because of the extensive redirections that have taken place in the Space Station Freedom Program in the past several years, the test bed effort was forced to accommodate a large number of changes. A short history of these program changes and their impact on the LeRC test beds is presented to understand how the current test bed configuration has evolved. The current test objectives and the development approach for the current DC Test Bed are discussed. A description of the test bed configuration, along with its power and controller hardware and its software components, is presented. Next, the uses of the test bed during the mature design and verification phase of SSFP are examined. Finally, the uses of the test bed in operation and evolution of the SSF are addressed.

Atropine unmasks bed-rest effect - A spectral analysis of cardiac interbeat intervals

NASA Technical Reports Server (NTRS)

Goldberger, Ary L.; Goldwater, Danielle; Bhargava, Valmik

1986-01-01

Heart rate spectral data obtained for 10 male subjects between 35-49 years following orthostatic tolerance testing with lower body negative pressure prebed rest and after 7-10 days of bed rest, while on placebo and after intravenous atropine are analyzed. Comparison of the spectral atropine rms for subjects prebed rest and after bed rest reveal a decrease from 63 + or - 24 ms to 40 + or - 23 ms. It is observed that heart rate interval variability for subjects after bed rest and with atropine is reduced; the heart rate at bed rest with atropine is increased from 70.4 + or - 12.4 beats/min prebed rest to 83.7 + or - 18.9 beats/min; and the exercise tolerance time for subjects in the atropine prebed-rest phase (658 + or - 352 s) is higher than the bed-rest phase (505 + or - 252 s). It is noted that bed rest impairs the cardiovascular capacity to adaptively modulate physiological responses, atropine exposes bed-rest deconditioning effects, and spectral analysis is useful for studying the effects of bed-rest deconditioning on cardiac dynamics.

Development of channel organization and roughness following sediment pulses in single‐thread, gravel bed rivers

USGS Publications Warehouse

Madej, Mary Ann

2001-01-01

Large, episodic inputs of coarse sediment (sediment pulses) in forested, mountain streams may result in changes in the size and arrangement of bed forms and in channel roughness. A conceptual model of channel organization delineates trajectories of response to sediment pulses for many types of gravel bed channels. Channels exhibited self‐organizing behavior to various degrees based on channel gradient, presence of large in‐channel wood or other forcing elements, the size of the sediment pulse, and the number of bed‐mobilizing flows since disturbance. Typical channel changes following a sediment pulse were initial decreases in water depth, in variability of bed elevations, and in the regularity of bed form spacing. Trajectories of change subsequently showed increased average water depth, more variable and complex bed topography, and increased uniformity of bed form spacing. Bed form spacing in streams with abundant forcing elements developed at a shorter spatial scale (two to five channel widths) than in streams without such forcing mechanisms (five to 10 channel widths). Channel roughness increased as bed forms developed.

Neonatal and pediatric intensive care in Rio de Janeiro State, Brazil: an analysis of bed distribution, 1997 and 2007.

PubMed

Barbosa, Arnaldo Prata; Cunha, Antônio José Ledo Alves da

2011-01-01

The objective of this study was to describe the characteristics of neonatal and pediatric intensive care units (ICU) and beds in Rio de Janeiro, correlating with population demands in 1997 and 2007. All neonatal and pediatric ICUs were visited, identifying the availability and type of beds. Comparisons were made between: supply and demand using projected need for beds for the population; public and private ICUs; and geographical regions. In 2007, 95 units were included totaling 1,094 beds (74 units and 1,080 beds in 1997): 51% public and 48% private (47% and 52% in 1997); 47% neonatal, 18% pediatric and 35% mixed units. Most units were located in the metropolitan area. The distribution of public and private beds was similar in the metropolitan area in both periods; in the interior, public beds tripled. Access has improved, mainly in the interior, but there is still no equity in the distribution of and accessibility to the available beds, with a shortage in the public sector, an excess in the private sector, and a great concentration in the metropolitan area.

Heat and mass transfer within partially wetted packed fractured granular beds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Khalil, E.B.; Karim, G.A.

1996-10-01

Fractured granular beds heated by hot gaseous streams have been the subject of numerous investigations in recent years due to their importance in many applications such as in in-situ and enhanced oil recovery. In a previous paper (Khalil and Karim, 1995) the results of an investigation of some aspects of the transport processes that occur within dry granular beds were reported. The present contribution examines similar beds when partially wetted. The granular beds were cylindrical in shape containing an axial central small diameter circular channel representing a fracture which can have different permeability from that of the main bed. Itmore » is shown that the mass flow rate of the hot gases, the relative permeability of the bed and the central channel as well as the initial liquid content of the bed control the drying rate. The results of an analytical model formulated to simulate the drying process in unobstructed channel beds showed good agreement with experimental results at low temperatures, however deviations occurred as the drying proceeds at higher temperatures.« less

Timing of chopper herbicide site preparation relative to bedding in the establishment of lower coastal plain pine plantations

Treesearch

Dwight K. Lauer; Harold E. Quicke

2006-01-01

The timing of Chopper® (BASF Corporation, Research Triangle Park, NC) herbicide applications before and after bedding was examined at four Lower Coastal Plain locations. Two bedding regimes, mid-season and late-season, were included at each location. Mid-season bedding occurred between May and July and late-season bedding between September and November. No post-plant...

Are tanning beds "safe"? Human studies of melanoma.

PubMed

Berwick, Marianne

2008-10-01

Controversy continues over the carcinogenic properties of tanning beds. The tanning industry "sells" tanning beds as a safe alternative to UV exposure for both tanning as well as vitamin D biosynthesis. But, how safe are tanning beds? Epidemiologic data - incomplete and unsatisfactory - suggests that tanning beds are not safer than solar ultraviolet radiation and that they may have independent effects from solar exposure that increase risk for melanoma.

Binge Eating Disorder.

PubMed

Guerdjikova, Anna I; Mori, Nicole; Casuto, Leah S; McElroy, Susan L

2017-06-01

Binge eating disorder (BED) is the most common eating disorder and an important public health problem. Lifetime prevalence of BED in the United States is 2.6%. In contrast to other eating disorders, the female to male ratio in BED is more balanced. BED co-occurs with a plethora of psychiatric disorders, most commonly mood and anxiety disorders. BED is also associated with obesity and its numerous complications. Although BED is similar in men and women in presentation and treatment outcomes, there are some key neurobiological differences that should be taken in consideration when personalizing treatment. Copyright © 2017 Elsevier Inc. All rights reserved.

3-D capacitance density imaging system

DOEpatents

Fasching, G.E.

1988-03-18

A three-dimensional capacitance density imaging of a gasified bed or the like in a containment vessel is achieved using a plurality of electrodes provided circumferentially about the bed in levels and along the bed in channels. The electrodes are individually and selectively excited electrically at each level to produce a plurality of current flux field patterns generated in the bed at each level. The current flux field patterns are suitably sensed and a density pattern of the bed at each level determined. By combining the determined density patterns at each level, a three-dimensional density image of the bed is achieved. 7 figs.

A Comparison of Tandem Walk Performance Between Bed Rest Subjects and Astronauts

NASA Technical Reports Server (NTRS)

Miller, Chris; Peters, Brian; Kofman, Igor; Philips, Tiffany; Batson, Crystal; Cerisano, Jody; Fisher, Elizabeth; Mulavara, Ajitkumar; Feiveson, Alan; Reschke, Millard;

Virulence of entomopathogenic bacteria in the bed bug, Cimex lectularius.

PubMed

Pietri, Jose E; Liang, Dangsheng

2018-01-01

Due in part to the development of insecticide resistance, the common bed bug, Cimex lectularius, has overcome human intervention efforts to make a global resurgence. The failure of chemical pesticides has created a need for novel strategies to combat bed bugs. While a number of insect pests are susceptible to the use of entomopathogenic microbes or microbial-derived toxins, biological control methods have not been thoroughly explored in bed bugs. Here, we tested the virulence of three entomopathogenic bacterial species in C. lectularius to determine their potential for bed bug control. We examined bed bug survival after inoculation with live or heat-killed Serratia marcescens, Pseudomonas fluorescens, and Bacillus thuringiensis israelensis at varying temperatures. We also analyzed the viability and growth of the same bacteria in infected bed bugs. All three bacterial species were pathogenic to bed bugs. However, the effects of S. marcescens and P. fluorescens were temperature-dependent while the lethality of B. thuringiensis israelensis was not. In addition, bacterial virulence was partly dependent on the route of infection but was not strongly associated with proliferation. Thus, our results suggest multiple possible mechanisms of microbial pathogenicity in the bed bug and indicate that entomopathogenic bacteria, or products derived from them, may have useful applications for bed bug control. Copyright © 2017 Elsevier Inc. All rights reserved.

Wave Driven Fluid-Sediment Interactions over Rippled Beds

NASA Astrophysics Data System (ADS)

Foster, Diane; Nichols, Claire

2008-11-01

Empirical investigations relating vortex shedding over rippled beds to oscillatory flows date back to Darwin in 1883. Observations of the shedding induced by oscillating forcing over fixed beds have shown vortical structures to reach maximum strength at 90 degrees when the horizontal velocity is largest. The objective of this effort is to examine the vortex generation and ejection over movable rippled beds in a full-scale, free surface wave environment. Observations of the two-dimensional time-varying velocity field over a movable sediment bed were obtained with a submersible Particle Image Velocimetry (PIV) system in two wave flumes. One wave flume was full scale and had a natural sand bed and the other flume had an artificial sediment bed with a specific gravity of 1.6. Full scale observations over an irregularly rippled bed show that the vortices generated during offshore directed flow over the steeper bed form slope were regularly ejected into the water column and were consistent with conceptual models of the oscillatory flow over a backward facing step. The results also show that vortices remain coherent during ejection when the background flow stalls (i.e. both the velocity and acceleration temporarily approach zero). These results offer new insight into fluid sediment interaction over rippled beds.

Reasons for tanning bed use: a survey of community college students in North Carolina.

PubMed

Neenan, Ashley; Lea, C Suzanne; Lesesky, Erin B

2012-01-01

Tanning bed use is classified as carcinogenic and is associated with an increased risk of skin cancer. The aim of this cross-sectional survey was to identify the most commonly stated reasons for tanning bed use among a sample of male and female community college students in eastern North Carolina. A brief, self-administered survey was distributed to students during English, Art, or Psychology class periods in 5 eastern North Carolina community colleges during the 2010 fall semester. The 95% response rate consisted of 487 returned surveys. Of the 487 respondents, 12.7% (N = 62) were current users, 24.5% (N = 119) were past users, and 62.2% (N = 303) reported never using tanning beds. Women (79%) were more likely than men (18%) to be current or former tanning bed users. Three African Americans reported current tanning bed use (4.8%). Reasons for tanning bed use were similar among men and women, with "I think I look better when I am tan" being the most commonly cited reason (70.2%) for tanning bed use. A convenience sample limits generalizability to all North Carolina students attending community college. Current tanning bed use was not widely reported. However, educational strategies for preventing tanning bed initiation or recurrence among male and female community college students should include appearance-driven factors.

Binge Eating among Women Veterans in Primary Care: Comorbidities and Treatment Priorities.

PubMed

Rosenbaum, Diane L; Kimerling, Rachel; Pomernacki, Alyssa; Goldstein, Karen M; Yano, Elizabeth M; Sadler, Anne G; Carney, Diane; Bastian, Lori A; Bean-Mayberry, Bevanne A; Frayne, Susan M

2016-01-01

Little is known about the clinical profile and treatment priorities of women with binge eating disorder (BED), a diagnosis new to the fifth edition of Diagnostic and Statistical Manual of Mental Disorders. We identified comorbidities and patients' treatment priorities, because these may inform implementation of clinical services. Data were collected from women veteran primary care patients. Analyses compared those who screened positive for BED (BED+), and those without any binge eating symptoms (BED-). Frequencies of comorbid medical and psychological disorders were high in the BED+ group. The BED+ group's self-identified most common treatment priorities were mood concerns (72.2%), weight loss (66.7%), and body image/food issues (50%). Among those with obesity, a greater proportion of the BED+ group indicated body image/food issues was their top treatment priority (12.9% vs. 2.8%; p < .01), suggesting that these patients may be more apt to seek treatment beyond weight management for their problematic eating patterns. Women primary care patients with BED demonstrate high medical and psychological complexity; their subjective treatment priorities often match objective needs. These findings may inform the development of targeted BED screening practices for women with obesity in primary care settings, and the eventual adoption of patient-centered BED treatment resources. Published by Elsevier Inc.

Effect of bed height and use of hands on trunk angular velocity during the sit-to-stand transfer.

PubMed

Lindemann, Ulrich; van Oosten, Leon; Evers, Jordi; Becker, Clemens; van Dieen, Jaap H; van Lummel, Rob C

2014-01-01

The ability to rise from a chair or bed is critical to an individual's quality of life because it determines functional independence. This study was to investigate the effect of bed height and use of hands on trunk angular velocity and trunk angles during the sit-to-stand (STS) performance. Twenty-four older persons (median age 74 years) were equipped with a body-fixed gyroscopic sensor and stood up from a bed adjusted to different heights, with and without the use of hands at each height. Peak angular velocity and trunk range of motion decreased with increasing bed height (all p ≤ 0.038) and were lower using hands during STS transfer indicating less effort. In conclusion, gyroscopic sensor data of the STS transfer of older persons show differences as an effect of bed height and use of hands. These results provide the rationale for recommending a relatively high bed height for most of the older persons. To minimise the effort during sit-to-stand transfer performance from bed, it is necessary to understand the effect of bed height and use of hands. It is concluded that a relatively high bed height and the use of hands is helpful for most of the older persons during sit-to-stand transfer.

Assessment of executive functioning in binge-eating disorder independent of weight status.

PubMed

Eneva, Kalina T; Arlt, Jean M; Yiu, Angelina; Murray, Susan M; Chen, Eunice Y

2017-08-01

Executive functioning (EF) problems may serve as vulnerability or maintenance factors for Binge-Eating Disorder (BED). However, it is unclear if EF problems observed in BED are related to overweight status or BED status. The current study extends this literature by examining EF in overweight and normal-weight BED compared to weight-matched controls. Participants were normal-weight women with BED (n = 23), overweight BED (n = 32), overweight healthy controls (n = 48), and normal-weight healthy controls (n = 29). The EF battery utilized tests from the National Institutes of Health (NIH) Toolbox and Delis-Kaplan Executive Function System (D-KEFS). After controlling for years of education and minority status, overweight individuals performed more poorly than normal-weight individuals on a task of cognitive flexibility requiring generativity (p < .01), and speed on psychomotor performance tasks (p = .01). Normal-weight and overweight BED performed worse on working memory tasks compared to controls (p = .04). Unexpectedly, normal-weight BED individuals out-performed all other groups on an inhibitory control task (p < .01). No significant differences were found between the four groups on tasks of planning. Regardless of weight status, BED is associated with working memory problems. Replication of the finding that normal-weight BED is associated with enhanced inhibitory control is needed. © 2017 Wiley Periodicals, Inc.

Application of CaO-Based Bed Material for Dual Fluidized Bed Steam Biomass Gasification

NASA Astrophysics Data System (ADS)

Koppatz, S.; Pfeifer, C.; Kreuzeder, A.; Soukup, G.; Hofbauer, H.

Gasification of biomass is a suitable option for decentralized energy supply based on renewable sources in the range of up to 50 MW fuel input. The paper presents the dual fluidized bed (DFB) steam gasification process, which is applied to generate high quality and nitrogen-free product gas. Essential part of the DFB process is the bed material used in the fluidized reactors, which has significant impact on the product gas quality. By the use of catalytically active bed materials the performance of the overall process is increased, since the bed material favors reactions of the steam gasification. In particular, tar reforming reactions are favored. Within the paper, the pilot plant based on the DFB process with 100kW fuel input at Vienna University of Technology, Austria is presented. Actual investigations with focus on CaO-based bed materials (limestone) as well as with natural olivine as bed material were carried out at the pilot plant. The application of CaO-based bed material shows mainly decreased tar content in the product gas in contrast to experiments with olivine as bed material. The paper presents the results of steam gasification experiments with limestone and olivine, whereby the product gas composition as well as the tar content and the tar composition are outlined.

Management and characteristics of recycled manure solids used for bedding in Midwest freestall dairy herds.

PubMed

Husfeldt, A W; Endres, M I; Salfer, J A; Janni, K A

2012-04-01

Interest in using recycled manure solids (RMS) as a bedding material for dairy cows has grown in the US Midwest. Cost of common bedding materials has increased in recent years and availability has decreased. Information regarding the composition of RMS and its use as a bedding material for dairy cows in the Midwest is very limited. The objectives of this study were to characterize RMS as a bedding material, observe bedding management practices, document methods of obtaining RMS, and describe housing facilities. We visited 38 Midwest dairy operations bedding freestalls with RMS to collect data. Methods of obtaining RMS for bedding included separation of anaerobic digested manure, separation of raw manure, and separation of raw manure followed by mechanical drum-composting for 18 to 24 h. Average bedding moisture of unused RMS was 72.4% with a pH of 9.16. Unused samples contained (on a dry basis) 1.4% N, 44.9% C, 32.7C:N ratio, 0.44% P, 0.70% K, 76.5% neutral detergent fiber, 9.4% ash, 4.4% nonfiber carbohydrates, and 1.1% fat. Moisture was lowest for drum-composted solids before and after use as freestall bedding. After use in the stalls, digested solids had lower neutral detergent fiber content (70.5%) than drum-composted (75.0%) and separated raw (73.1%) solids. Total N content was greater in digested solids (2.0%) than in separated raw (1.7%) solids. Total bacterial populations in unused bedding were greatest in separated raw manure solids but were similar between digested and drum-composted manure solids. Drum-composted manure solids had no coliform bacteria before use as freestall bedding. After use as bedding, digested manure solids had lower total bacteria counts compared with drum-composted and separated raw manure solids, which had similar counts. Used bedding samples of digested solids contained fewer environmental streptococci than drum-composted and separated raw solids and had reduced Bacillus counts compared with separated raw solids. Coliform counts were similar for all 3 bedding sources. Addition of a mechanical blower post-separation and use of a shelter for storage were associated with reduced fresh-bedding moisture but not associated with bacterial counts. This was the first survey of herds using RMS for bedding in the Midwest. We learned that RMS was being used successfully as a source of bedding for dairy cows. For most farms in the study, somatic cell count was comparable to the average in the region and not excessively high. Copyright © 2012 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Orlistat with behavioral weight loss for obesity with versus without binge eating disorder: randomized placebo-controlled trial at a community mental health center serving educationally and economically disadvantaged Latino/as.

PubMed

Grilo, Carlos M; White, Marney A

2013-03-01

This study was a randomized placebo-controlled trial testing the addition of orlistat to behavioral weight loss for obesity in Spanish-speaking-only Latino/as with versus without binge eating disorder (BED) performed at a community mental health center serving educationally- and economically-disadvantaged patients. Latino/as have high rates of obesity but are under-represented in obesity treatment studies and despite comparable-to-or-higher rates of BED than Whites, Latino/as are under-represented in BED treatment studies. BED is associated with obesity but whether it predicts/moderates treatment outcomes remains uncertain. Thus, this study also tested whether BED prospectively predicts/moderates outcomes. Seventy-nine obese Spanish-speaking-only Latino/as with BED (N=40) versus without BED (N=39) at a community mental health center were randomly assigned to four-months of orlistat-plus-BWL or placebo-plus-BWL. BWL was culturally-enhanced modification of Diabetes-Prevention-Program delivered in weekly sessions in Spanish. Orlistat (120 mg tid) and matching-placebo delivered with standard clinical-management. Participants were assessed independently throughout treatment, post-treatment, and six-month follow-up. 78% completed treatments; completion rates did not differ significantly by medication or BED. Intent-to-treat mixed-models analyses revealed significant improvements in binge eating, eating-psychopathology, and depression, and significant--albeit modest--weight-loss. Overall, the addition of orlistat to BWL was not associated with greater improvements; however, BED moderated weight-loss: orlistat-plus-BWL produced significantly greater weight-loss in non-BED group but not in BED. Improvements were maintained through 6-month follow-up; BED significantly predicted/moderated increases in eating concerns and depression following treatment. Within BED-group, binge-eating remission rates were 65% (post-treatment) and 50% (follow-up). In this controlled trial performed at community mental health center serving educationally- and economically-disadvantaged Spanish-speaking-only Latino/as with co-morbid psychiatric needs, we observed outcomes for the BWL plus orlistat/placebo medication that approximate or are slightly dampened relative to the literature for efficacy trials with much more restrictive obese and BED samples. In this complex patient group, adding orlistat to BWL produced greater weight-loss than adding placebo among obese patients without BED but not among those with BED. Although 50% of BED patients maintained abstinence from binge-eating following these specific obesity treatments (BWL plus orlistat/placebo), BED was a negative prognostic indicator for some outcome variables. clinicaltrials.gov Identifier: NCT00516919. Copyright © 2013 Elsevier Ltd. All rights reserved.

Comparison of Ocular Outcomes in Two 14-Day Bed Rest Studies

NASA Technical Reports Server (NTRS)

Cromwell, R. L.; Zanello, S. B.; Yarbough, P. O.; Taibbi, G.; Vizzeri, G.

2011-01-01

Reports of astronauts visual changes raised concern about ocular health during long-duration spaceflight. Some of these findings included hyperopic shifts, choroidal folds, optic disc edema, retinal nerve fiber layer (RNFL) thickening, and cotton wool spots. While the etiology remains unknown, hypotheses speculate that hypertension in the brain caused by cephalad fluid shifts during spaceflight is a possible mechanism for these ocular changes. Head-down tilt (HDT) bed rest is a spaceflight analog that induces cephalad fluid shifts. In addition, previous studies of the HDT position demonstrated body fluid shifts associated with changes in intraocular pressure (IOP). For these reasons, vision monitoring of HDT bed rest subjects was implemented for NASA bed rest studies. Subjects selected for these studies were healthy adults (14 males and 5 females). Average age was 37.5 plus or minus 9.1 years, weight was 77.4 plus or minus 11.3 Kg, and height was 173.4 plus or minus 7.2 14 cm. Controlled conditions followed for all NASA bed rest studies were implemented. These conditions included factors such as eating a standardized diet, maintaining a strict sleep wake cycle, and remaining in bed for 24 hours each day. In one study, subjects maintained a horizontal (0 degree) position while in bed and were exercised six days per week with an integrated resistance and aerobic training (iRAT) program. In the other study, subjects were placed at 6 degrees HDT while in bed and did not engage in exercise. All subjects underwent pre- and post bed rest vision testing. While the battery of vision tests for each study was not identical, measures common to both studies will be presented. These measures included IOP and measures that provided an indication of optic disc swelling as derived from optical coherence tomography (OCT) testing: average retinal nerve fiber layer (RNFL) thickness (millimeters), disc area (square millimeters), rim area (square millimters), and average cup to disc (C/D) ratio. For all measures, there was no significant difference between subject groups for pre-bed rest testing. Post bed rest values also remained similar between groups. Comparison of pre- to post bed rest testing within each group did not demonstrate any statistical differences. These preliminary results from 14-day bed rest studies suggest that the combination of exercise and horizontal bed rest as compared to 6 degrees HDT bed rest did not produce differences in the ocular response with regard to IOP and optic disc parameters. The ocular measures reported here only included pre- and post bed rest time points. Further investigation is needed to examine both the acute response and long term adaptation of structural and functional ocular parameters in the bed rest platform and determine its usefulness for studying spaceflight phenomena. From a clinical perspective, the ability to study ocular responses in the controlled environment of the bed rest platform can provide valuable information for the care of patients restricted to bed rest.

A method for improving predictions of bed-load discharges to reservoirs

USGS Publications Warehouse

Lopes, V.L.; Osterkamp, W.R.; Bravo-Espinosa, M.

2007-01-01

Effective management options for mitigating the loss of reservoir water storage capacity to sedimentation depend on improved predictions of bed-load discharges into the reservoirs. Most predictions of bed-load discharges, however, are based on the assumption that the rates of bed-load sediment availability equal the transport capacity of the flow, ignoring the spatio-temporal variability of the sediment supply. This paper develops a semiquantitative method to characterize bed-load sediment transport in alluvial channels, assuming a channel reach is non-supply limited when the bed-load discharge of a given sediment particle-size class is functionally related to the energy that is available to transport that fraction of the total bed-load. The method was applied to 22 alluvial stream channels in the USA to determine whether a channel reach had a supply-limited or non-supply-limited bed-load transport regime. The non-supply-limited transport regime was further subdivided into two groups on the basis of statistical tests. The results indicated the pattern of bed-load sediment transport in alluvial channels depends on the complete spectrum of sediment particle sizes available for transport rather than individual particle-size fractions represented by one characteristic particle size. The application of the method developed in this paper should assist reservoir managers in selecting bed-load sediment transport equations to improve predictions of bed-load discharge in alluvial streams, thereby significantly increasing the efficiency of management options for maintaining the storage capacity of waterbodies. ?? 2007 Blackwell Publishing Asia Pty Ltd.

Numerical simulation of dune-flat bed transition and stage‐discharge relationship with hysteresis effect

USGS Publications Warehouse

Shimizu, Yasuyuki; Giri, Sanjay; Yamaguchi, Satomi; Nelson, Jonathan M.

2009-01-01

This work presents recent advances on morphodynamic modeling of bed forms under unsteady discharge. This paper includes further development of a morphodynamic model proposed earlier by Giri and Shimizu (2006a). This model reproduces the temporal development of river dunes and accurately replicates the physical properties associated with bed form evolution. Model results appear to provide accurate predictions of bed form geometry and form drag over bed forms for arbitrary steady flows. However, accurate predictions of temporal changes of form drag are key to the prediction of stage‐discharge relation during flood events. Herein, the model capability is extended to replicate the dune–flat bed transition, and in turn, the variation of form drag produced by the temporal growth or decay of bed forms under unsteady flow conditions. Some numerical experiments are performed to analyze hysteresis of the stage‐discharge relationship caused by the transition between dune and flat bed regimes during rising and falling stages of varying flows. The numerical model successfully simulates dune–flat bed transition and the associated hysteresis of the stage‐discharge relationship; this is in good agreement with physical observations but has been treated in the past only using empirical methods. A hypothetical relationship for a sediment parameter (the mean step length) is proposed to a first level of approximation that enables reproduction of the dune–flat bed transition. The proposed numerical model demonstrates its ability to address an important practical problem associated with bed form evolution and flow resistance in varying flows.

Packing microstructure and local density variations of experimental and computational pebble beds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Auwerda, G. J.; Kloosterman, J. L.; Lathouwers, D.

2012-07-01

In pebble bed type nuclear reactors the fuel is contained in graphite pebbles, which form a randomly stacked bed with a non-uniform packing density. These variations can influence local coolant flow and power density and are a possible cause of hotspots. To analyse local density variations computational methods are needed that can generate randomly stacked pebble beds with a realistic packing structure on a pebble-to-pebble level. We first compare various properties of the local packing structure of a computed bed with those of an image made using computer aided X-ray tomography, looking at properties in the bulk of the bedmore » and near the wall separately. Especially for the bulk of the bed, properties of the computed bed show good comparison with the scanned bed and with literature, giving confidence our method generates beds with realistic packing microstructure. Results also show the packing structure is different near the wall than in the bulk of the bed, with pebbles near the wall forming ordered layers similar to hexagonal close packing. Next, variations in the local packing density are investigated by comparing probability density functions of the packing fraction of small clusters of pebbles throughout the bed. Especially near the wall large variations in local packing fractions exists, with a higher probability for both clusters of pebbles with low (<0.6) and high (>0.65) packing fraction, which could significantly affect flow rates and, together with higher power densities, could result in hotspots. (authors)« less

Suicidality in adolescents and adults with binge-eating disorder: Results from the national comorbidity survey replication and adolescent supplement.

PubMed

Forrest, Lauren N; Zuromski, Kelly L; Dodd, Dorian R; Smith, April R

2017-01-01

The relation between binge-eating disorder (BED) and suicidality (i.e., suicide ideation, plan, and/or attempt) has not been studied extensively, and it is unknown whether BED is uniquely associated with suicidality when adjusting for comorbid psychopathology. Moreover, the course of suicidality in BED has not been determined and it is unknown whether BED precedes suicidality or vice versa. A total of 10,123 adolescents and 2,980 adults from two nationally representative surveys were administered diagnostic interviews assessing psychopathology and suicidality, as well the retrospectively reported ages of onset. Among adults and adolescents, BED was associated with elevated odds of suicide ideation, plan, and attempt at a univariate level, but BED was not associated with elevated odds of suicidality when adjusting for comorbid psychopathology. Kaplan-Meier estimates of temporal patterns displayed that most adolescents experienced suicidality onset following BED onset, whereas most adults experienced suicidality onset prior to BED onset. BED, comorbid disorders, and suicidality share common factors and interrelations, and individuals with BED and comorbid disorders may be at particularly high risk for suicidal outcomes. The presence of BED in adolescence may serve as a marker for more severe symptomatology that precedes the occurrence of suicidality. Research is needed to understand how eating disorder symptoms, comorbid symptoms, and suicidality affect one another over time. © 2016 Wiley Periodicals, Inc. (Int J Eat Disord 2017; 50:40-49). © 2016 Wiley Periodicals, Inc.

Key Spatial Factors Influencing the Perceived Privacy in Nursing Units: An Exploration Study With Eight Nursing Units in Hong Kong.

PubMed

Lu, Yi; Cai, Hui; Bosch, Sheila J

2017-07-01

This study examined how the spatial characteristics of patient beds, which are influenced by patient room design and nursing unit configuration, affect patients' perceptions about privacy. In the hospital setting, most patients expect a certain degree of privacy but also understand that their caregivers need appropriate access to them in order to provide high-quality care. Even veteran healthcare designers may struggle to create just the right balance between privacy and accessibility. A paper-based survey was conducted with 159 participants in Hong Kong-72 (45.3%) participants had been hospitalized and 87 (54.7%) participants had not-to document their selection of high-privacy beds, given simplified plans of eight nursing units. Two types of information, comprised of six variables, were examined for each bed. These include (1) room-level variables, specifically the number of beds per room and area per bed and (2) relational variables, including walking distance, directional change, integration, and control. The results demonstrate that when asked to identify high-privacy beds, participants selected beds in patient rooms with fewer beds per room, a larger area per bed, and a longer walking distance to the care team workstation. Interestingly, the participants having been hospitalized also chose beds with a visual connection to the care team workstation as being high in privacy. The participants with hospitalization experience may be willing to accept a bed with reduced visual privacy, perhaps out of a concern for safety.

Coastal geomorphic conditions and styles of storm surge washover deposits from Southern Thailand

NASA Astrophysics Data System (ADS)

Phantuwongraj, Sumet; Choowong, Montri; Nanayama, Futoshi; Hisada, Ken-Ichiro; Charusiri, Punya; Chutakositkanon, Vichai; Pailoplee, Santi; Chabangbon, Akkaneewut

2013-06-01

The characteristics of tropical storm washover deposits laid down during the years 2007 to 2011 along the southern peninsular coast of the Gulf of Thailand (GOT) were described in relation to their different geomorphic conditions, including perched fan, washover terrace and sheetwash lineations preserved behind the beach zone within 100 m of the shoreline. As a result, washover terrace and sheetwash lineations were found where the beach configuration was uniform and promoted an unconfined flow. Non-uniform beach configurations that promoted a confined flow resulted in a perched fan deposit. Washover sediments were differentiated into two types based on sedimentary characteristics, including (i) a thick-bedded sand of multiple reverse grading layers and (ii) a medium-bedded sand of multiple normal grading layers. In the case of thick-bedded washover deposits, the internal sedimentary structures were characterized by the presence of sub-horizontal bedding, reverse grading, lamination, foreset bedding and wavy bedding, whereas, horizontal bedding, normal grading, and dunes were the dominant structures in the medium-bedded washover sand. Rip-up clasts were rare and recognized only in the washover deposits in the bottom unit, which reflects the condition when a mud supply was available. All washover successions were found in the landward inclined-bedding with a basal sharp contact. A high elevated beach ridge associated with a large swale at the backshore proved suitable for a thick-bedded washover type, whereas a small beach ridge with uniformly flat backshore topography promoted a medium-bedded washover sediment.

Active magnetic regenerator method and apparatus

DOEpatents

DeGregoria, Anthony J.; Zimm, Carl B.; Janda, Dennis J.; Lubasz, Richard A.; Jastrab, Alexander G.; Johnson, Joseph W.; Ludeman, Evan M.

1993-01-01

In an active magnetic regenerator apparatus having a regenerator bed of material exhibiting the magnetocaloric effect, flow of heat transfer fluid through the bed is unbalanced, so that more fluid flows through the bed from the hot side of the bed to the cold side than from the cold side to the hot side. The excess heat transfer fluid is diverted back to the hot side of the bed. The diverted fluid may be passed through a heat exchanger to draw heat from a fluid to be cooled. The apparatus may be operated at cryogenic temperatures, and the heat transfer fluid may be helium gas and the fluid to be cooled may be hydrogen gas, which is liquified by the device. The apparatus can be formed in multiple stages to allow a greater span of cooling temperatures than a single stage, and each stage may be comprised of two bed parts. Where two bed parts are employed in each stage, a portion of the fluid passing from the hot side to the cold side of a first bed part which does not have a magnetic field applied thereto is diverted back to the cold side of the other bed part in the stage, where it is passed through to the hot side. The remainder of the fluid from the cold side of the bed part of the first stage is passed to the hot side of the bed part of the second stage.

Effects of 21 days of bed rest, with or without artificial gravity, on nutritional status of humans

PubMed Central

Zwart, S. R.; Crawford, G. E.; Gillman, P. L.; Kala, G.; Rodgers, A. S.; Rogers, A.; Inniss, A. M.; Rice, B. L.; Ericson, K.; Coburn, S.; Bourbeau, Y.; Hudson, E.; Mathew, G.; DeKerlegand, D. E.; Sams, C. F.; Heer, M. A.; Paloski, W. H.; Smith, S. M.

2009-01-01

Spaceflight and bed rest models of microgravity have profound effects on physiological systems, including the cardiovascular, musculoskeletal, and immune systems. These effects can be exacerbated by suboptimal nutrient status, and therefore it is critical to monitor nutritional status when evaluating countermeasures to mitigate negative effects of spaceflight. As part of a larger study to investigate the usefulness of artificial gravity as a countermeasure for musculoskeletal and cardiovascular deficits during bed rest, we tested the hypothesis that artificial gravity would have an effect on some aspects of nutritional status. Dietary intake was recorded daily before, during, and after 21 days of bed rest with artificial gravity (n = 8) or bed rest alone (n = 7). We examined body composition, hematology, general blood chemistry, markers of oxidative damage, and blood levels of selected vitamins and minerals before, during, and after the bed rest period. Several indicators of vitamin status changed in response to diet changes: serum α- and γ-tocopherol and urinary 4-pyridoxic acid decreased (P < 0.001) and plasma β-carotene increased (P < 0.001) in both groups during bed rest compared with before bed rest. A decrease in hematocrit (P < 0.001) after bed rest was accompanied by a decrease in transferrin (P < 0.001), but transferrin receptors were not changed. These data provide evidence that artificial gravity itself does not negatively affect nutritional status during bed rest. Likewise, artificial gravity has no protective effect on nutritional status during bed rest. PMID:19074571

Fluidized bed operations survey summary

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lombardi, C.

1996-12-31

A fluidized bed operations survey summary is presented. The survey contains information on: forced outage causes; forced outage concerns ranked numerically; 1996 boiler operation and maintenance (O&M) concerns; 1997 boiler O&M concerns; fluidized bed capacity factor results; and fluidized bed total outage time.

Electric versus hydraulic hospital beds: differences in use during basic nursing tasks.

PubMed

Capodaglio, Edda Maria

2013-01-01

Biomechanical, postural and ergonomic aspects during real patient-assisting tasks performed by nurses using an electric versus a hydraulic hospital bed were observed. While there were no differences in the flexed postures the nurses adopted, longer performance times were recorded when electric beds were used. Subjective effort, force exertion and lumbar shear forces exceeding safety limits proved electric beds were superior. Patients' dependency level seemed to influence the type of nurses' intervention (duration and force actions), irrespective of the bed used. The nurses greatly appreciated the electric bed. Its use seemed to reduce the level of effort perceived during care giving and the postural load during critical subtasks. Ergonomics and organizational problems related to adopting electric beds in hospital wards should be addressed further to make their use more efficient.

Pharmacologic counter measures minimizing post-space flight orthostatic intolerance. [bed rest, drug disposition, and physiological function

NASA Technical Reports Server (NTRS)

Harrison, D. C.; Kates, R.

1982-01-01

The effect of bed rest on drug disposition and physiological function was investigated as part of a project to determine the cardiovascular effects of space flight. One group of subjects was given doses of lidocane, penicillin-G, and ICG during a control period and following seven days of bed rest. Cardiac function was evaluated by echo-cardiography. Renal function was evaluated in a second group before and after several days of bed rest. Inulin, para-aminohippurate, and dextran clearances were studied. In the first group, the post-bed rest parameters were not statistically different from the pre-bed rest valves. In the second study, renal function did not change significantly after seven days of bed rest. Plans for future research are reviewed.

Fast fluidized bed steam generator

DOEpatents

Bryers, Richard W.; Taylor, Thomas E.

1980-01-01

A steam generator in which a high-velocity, combustion-supporting gas is passed through a bed of particulate material to provide a fluidized bed having a dense-phase portion and an entrained-phase portion for the combustion of fuel material. A first set of heat transfer elements connected to a steam drum is vertically disposed above the dense-phase fluidized bed to form a first flow circuit for heat transfer fluid which is heated primarily by the entrained-phase fluidized bed. A second set of heat transfer elements connected to the steam drum and forming the wall structure of the furnace provides a second flow circuit for the heat transfer fluid, the lower portion of which is heated by the dense-phase fluidized bed and the upper portion by the entrained-phase fluidized bed.

Multi-scale fracture networks within layered shallow water tight carbonates

NASA Astrophysics Data System (ADS)

Panza, Elisa; Agosta, Fabrizio; Rustichelli, Andrea; Vinciguerra, Sergio; Zambrano, Miller; Prosser, Giacomo; Tondi, Emanuele

2015-04-01

The work is aimed at deciphering the contribution of background deformation and persistent fracture zones on the fluid flow properties of tight platform carbonates. Taking advantage of 3D exposures present in the Murge area of southern Italy, the fracture networks crosscutting at different scales the layered Cretaceous limestone of the Altamura Fm. were analyzed. The rock multi-layer is characterized by 10's of cm-thick, sub-horizontal, laterally continuous carbonate beds. Each bed commonly represents a shallowing-upward peritidal cycle made up of homogeneous micritic limestones grading upward to cm-thick stromatolitic limestones and/or fenestral limestones. The bed interfaces are formed by sharp maximum flooding surfaces. Porosity measurements carried out on 40 limestone samples collected from a single carbonate bed show values ranging between 0,5% and 5,5%. Background deformation includes both stratabound and non-stratabound fractures. The former elements consist of bed-perpendicular joints and sheared joints, which are confined within a single bed and often displace small, bed-parallel stylolites. Non-stratabound fractures consist of incipient, cm offset, sub-vertical strike-slip faults, which crosscut the bed interfaces. The aforementioned elements are often confined within individual bed-packages, which are identified by presence of pronounced surfaces locally marked by veneers of reddish clayey paleosoils. Persistent fracture zones consist of 10's of m-high, 10's of cm-offset strike-slip faults that offset the bed-package interfaces and are confined within individual bed-packages association. Laterally discontinuous, cm- to a few m-thick paleokarstic breccia levels separate the different bed-packages associations. Persistent fracture zones include asymmetric fractured damage zones and mm-thick veneers of discontinuous fault rocks. The fracture networks that pervasively crosscut the study limestone multi-layer are investigated by mean of scanline and scanarea methodologies. The dimensional, spatial and scaling properties of both stratabound and non-stratabound fractures are documented along single beds and bed-packages, respectively. Persistent fracture zones are studied from individual bed-package associations. By computing the intensity, height distribution, aspect ratio, aperture of each fracture/fault set, DFN (Discrete Fracture Network) models are built for the aforementioned different scales of observation. DFN models of single beds and bed-packages include stratabound and non-stratabound fractures. Differently, the DFN model of a bed-packages association also includes persistent fracture zones and related damage zones. To check the results of our computations, we also build up a smaller scale, 1m3 geocellular volume in which fractures are inserted one at time in the model. All DFN models do not include the matrix porosity. Porosity and 3D permeability (Kx, Ky, Kz) values are obtained as outputs of the DFN models. The results are consistent with the most prominet set of non-stratabound fractures being the major control on the petrophysical properties of both single beds and bed-packages. As expected, the persistent fractures zones strongly affect both porosity and permeability of the bed-packages association. The results of ongoing laboratory analyses on representative limestone samples not only will provide a quantitative assessment of the physical properties of the matrix in terms of porosity and permeability, but also will shed new light on the geometry, density and anisotropy of microfractures and their role on fluid flow properties.

Ability of organic and inorganic bedding materials to promote growth of environmental bacteria.

PubMed

Godden, S; Bey, R; Lorch, K; Farnsworth, R; Rapnicki, P

2008-01-01

The major objective of this study was to contrast the ability of 4 commonly utilized bedding materials to promote growth of environmental bacteria under controlled conditions. A second objective was to describe the relationship between bacterial growth and specific biochemical or nutritional properties of these bedding materials. Unused samples of clean sand (CS; n = 20), recycled sand (RS; n = 21), digested manure solids (DS; n = 15), and shavings (SH; n = 15) were collected from bedding storage areas on 49 commercial Minnesota and Wisconsin dairy farms. Sterilized bedding samples were inoculated with Klebsiella pneumoniae and Enterococcus faecium then incubated, in triplicate, for 72 h at 37 degrees C. Subsamples were collected after 0, 24, 48, and 72 h of incubation for culture and enumeration of bacteria. Subsamples of bedding were also tested for pH, total C content (%), and total N content (%). If bacterial growth occurred, peak levels were typically achieved within 24 h. Digested manure solids promoted the greatest amounts of growth of K. pneumoniae, followed by RS and then SH, whereas CS promoted the least. There would seem to be a tradeoff in selecting SH as a bedding material, because it supported moderate growth of K. pneumoniae but caused a rapid decline in the numbers of E. faecium. However, RS, CS, and DS each only supported relatively small amounts of growth of E. faecium, so the benefit of SH relative to other bedding materials is limited. High bedding pH may partially explain why some bedding materials supported growth of E. faecium (e.g., DS and RS). Both high bedding pH (e.g., as for DS or RS) and high total C (%) content (e.g., as for DS and SH) may partially explain why some bedding materials supported growth of K. pneumoniae.

Bone metabolism and nutritional status during 30-day head-down-tilt bed rest

PubMed Central

Morgan, Jennifer L. L.; Zwart, Sara R.; Heer, Martina; Ploutz-Snyder, Robert; Ericson, Karen

2012-01-01

Bed rest studies provide an important tool for modeling physiological changes that occur during spaceflight. Markers of bone metabolism and nutritional status were evaluated in 12 subjects (8 men, 4 women; ages 25–49 yr) who participated in a 30-day −6° head-down-tilt diet-controlled bed rest study. Blood and urine samples were collected twice before, once a week during, and twice after bed rest. Data were analyzed using a mixed-effects linear regression with a priori contrasts comparing all days to the second week of the pre-bed rest acclimation period. During bed rest, all urinary markers of bone resorption increased ∼20% (P < 0.001), and serum parathyroid hormone decreased ∼25% (P < 0.001). Unlike longer (>60 days) bed rest studies, neither markers of oxidative damage nor iron status indexes changed over the 30 days of bed rest. Urinary oxalate excretion decreased ∼20% during bed rest (P < 0.001) and correlated inversely with urinary calcium (R = −0.18, P < 0.02). These data provide a broad overview of the biochemistry associated with short-duration bed rest studies and provide an impetus for using shorter studies to save time and costs wherever possible. For some effects related to bone biochemistry, short-duration bed rest will fulfill the scientific requirements to simulate spaceflight, but other effects (antioxidants/oxidative damage, iron status) do not manifest until subjects are in bed longer, in which case longer studies or other analogs may be needed. Regardless, maximizing research funding and opportunities will be critical to enable the next steps in space exploration. PMID:22995395

Molecular Basis of N,N-Diethyl-3-Methylbenzamide (DEET) in Repelling the Common Bed Bug, Cimex lectularius.

PubMed

Liu, Feng; Xia, Xiaoming; Liu, Nannan

2017-01-01

As the most extensively used chemical repellent, N,N-diethyl-3-methylbenzamide (DEET) displayed repellency to a wide range of insects, including the common bed bug, Cimex lectularius . While the neuronal or molecular basis involved in DEET's repellency have been majorly focused on mosquitos and fruit flies, DEET's repellency to the common bed bug is largely unreached. To gain new insights into the cellular and molecular mechanisms in DEET's repellency to the common bed bug, we characterized the neuronal response of bed bugs to DEET, identified the olfactory receptors targeted by DEET and demonstrated the interfering effect of DEET on bed bug's responses to human odorants. High doses of DEET were required for activating the olfactory receptor neurons in the sensilla of bed bugs and at least three DEET-sensitive receptors were functionally deciphered. These DEET-sensitive receptors presented even more sensitive to certain botanical terpenes/terpenoids which also displayed repellency at varying levels for bed bugs. In addition, DEET produced a blocking effect on the neuronal responses of bed bugs to specific human odors and showed inhibitory effect on the function of odorant receptors in responding to certain human odors. Taken together, our results indicate that DEET may function as a stimulus that triggers avoidance behaviors and a molecular "confusant" for interrupting the host odor recognition in the odorant receptors of bed bugs. The receptors that coincidently responded to both synthetic DEET and botanical terpenes/terpenoids suggested that DEET probably target on receptors that originally responded to terpenes/terpenoids. This study gave novel insight into the mechanisms of DEET's repellency to bed bugs and also provided valuable information for developing new reagents for bed bug control.

Coupling Solute and Fine Particle Transport with Sand Bed Morphodynamics within a Field Experiment

NASA Astrophysics Data System (ADS)

Phillips, C. B.; Ortiz, C. P.; Schumer, R.; Jerolmack, D. J.; Packman, A. I.

2017-12-01

Fine suspended particles are typically considered to pass through streams and rivers as wash load without interacting with the bed, however experiments have demonstrated that hyporheic flow causes advective exchange of fine particles with the stream bed, yielding accumulation of fine particle deposits within the bed. Ultimately, understanding river morphodynamics and ecosystem dynamics requires coupling both fine particle and solute transport with bed morphodynamics. To better understand the coupling between these processes we analyze a novel dataset from a controlled field experiment conducted on Clear Run, a 2nd order sand bed stream located within the North Carolina coastal plain. Data include concentrations of continuously injected conservative solutes and fine particulate tracers measured at various depths within the stream bed, overhead time lapse images of bed forms, stream discharge, and geomorphological surveys of the stream. We use image analysis of bed morphodynamics to assess exchange, retention, and remobilization of solutes and fine particles during constant discharge and a short duration experimental flood. From the images, we extract a time series of bedform elevations and scour depths for the duration of the experiment. The high-resolution timeseries of bed elevation enables us to assess coupling of bed morphodynamics with both the solute and fine particle flux during steady state mobile bedforms prior to the flood and to changing bedforms during the flood. These data allow the application of a stochastic modeling framework relating bed elevation fluctuations to fine particle residence times. This combined experimental and modeling approach ultimately informs our ability to predict not only the fate of fine particulate matter but also associated nutrient and carbon dynamics within streams and rivers.

The association between number of doctors per bed and readmission of elderly patients with pneumonia in South Korea.

PubMed

Lee, Joo Eun; Kim, Tae Hyun; Cho, Kyoung Hee; Han, Kyu-Tae; Park, Eun-Cheol

2017-06-08

There is an urgent need to reduce readmission of patients with pneumonia and improve quality of care. To assess the association between hospital resources and quality of care, we examined the effect of number of doctors per bed on 30-day readmission and investigated the combined effect of number of doctors per bed and number of beds. We used nationwide cohort sample data of health insurance claims by the National Health Insurance Service (NHIS) from 2002 to 2013. Pneumonia admissions to acute care hospitals among 7446 inpatients older than 65 were examined. We conducted a multivariate Cox proportional hazard model to analyze the association between the number of doctors per bed and 30-day readmission, as well as that of pneumonia-specific 30-day readmission with the combined effects of number of doctors per bed and number of beds. Overall, 1421 (19.1%) patients were readmitted within 30 days and 756 (11.2%) patients were readmitted for pneumonia within 30 days. Patients with pneumonia treated by very low or low number of doctors per bed showed higher readmission (pneumonia-specific readmission: hazard ratio [HR] = 1. 406, 95% confidence interval [CI] = 1.072-1.843 for low number of doctors per bed; all-cause readmissions: HR = 1.276, 95% CI = 1.026-1.587 for very low number of doctors per bed, and HR = 1.280, 95% CI = 1.064-1.540 for low number of doctors per bed). This empirical study showed that patients with pneumonia cared for in hospitals with more doctors were less likely to be readmitted. Pneumonia-specific 30-day readmission was also significantly associated with the combined effect of the number of doctors and the number of hospital beds.

Cacao bean husk: an applicable bedding material in dairy free-stall barns.

PubMed

Yajima, Akira; Owada, Hisashi; Kobayashi, Suguru; Komatsu, Natsumi; Takehara, Kazuaki; Ito, Maria; Matsuda, Kazuhide; Sato, Kan; Itabashi, Hisao; Sugimura, Satoshi; Kanda, Shuhei

2017-07-01

The objectives of the study were to assess the effect of cacao bean husk as bedding material in free-stall barn on the behavior, productivity, and udder health of dairy cattle, and on the ammonia concentrations in the barn. Four different stall surfaces (no bedding, cacao bean husk, sawdust, and chopped wheat straw) were each continuously tested for a period of 1 week to determine their effects on nine lactating Holstein cows housed in the free-stall barn with rubber matting. The lying time and the milk yield were measured between d 4 and d 7. Blood samples for plasma cortisol concentration and teat swabs for bacterial counts were obtained prior to morning milking on d 7. The time-averaged gas-phase ammonia concentrations in the barn were measured between d 2 and d 7. The cows spent approximately 2 h more per day lying in the stalls when bedding was available than without bedding. The milk yield increased in the experimental periods when cows had access to bedding materials as compared to the period without bedding. The lying time was positively correlated with the milk yield. Bacterial counts on the teat ends recorded for cows housed on cacao bean husk were significantly lower than those recorded for cows housed without bedding. Ammonia concentration under cacao bean husk bedding decreased by 6%, 15%, and 21% as compared to no bedding, sawdust, and chopped wheat straw, respectively. The cortisol concentration was lowest in the period when cacao bean husk bedding was used. We observed a positive correlation between the ammonia concentrations in the barn and the plasma cortisol concentrations. Cacao bean husk is a potential alternative of conventional bedding material, such as sawdust or chopped wheat straw, with beneficial effects on udder health and ammonia concentrations in the barns.

Breakup and reestablishment of the armour layer in a large gravel-bed river below dams: The lower Ebro

NASA Astrophysics Data System (ADS)

Vericat, Damia; Batalla, Ramon J.; Garcia, Celso

2006-06-01

Changes in armour layer during floods under supply limited conditions are little known. This paper describes the breakup and the reestablishment of the bed armour layer in the regulated gravel-bed Ebro River during a flooding period. The study was conducted over a 28-km study reach from 2002 to 2004. The surface, subsurface and bed load grain size distribution constitute the bases for the analysis of bed-armouring dynamics. The results indicate that the magnitude of floods controlled the degree of armouring of the river bed. The initial mean armouring ratio was 2.3, with maximum values reaching 4.4. Floods in the winter of 2002-2003 ( Q8) caused the breakup of the armour layer in several sections. This resulted in the erratic bed load pattern observed during the December 2002 flushing flow and in the increase in bed load transport during successive events. Most grain size classes were entrained and transported, causing river bed incision. The mean armouring ratio decreased to 1.9. In contrast, during low magnitude floods in 2003-2004 ( Q2), the coarsest fractions (64 mm) did not take part in the bed load while finer particles were winnowed, thus surface deposits coarsened. As a result, the armour layer was reestablished (i.e., the mean armouring ratio increased to 2.3), and the supply of subsurface sediment decreased. The supply and transport of bed material appear to be in balance in the river reach immediately below the dam. In contrast, the transport of medium and finer size classes in the downstream reaches was higher than their supply from upstream, a phenomenon that progressively reduced their availability in the river bed surface, hence the armour layer reworking.

Comparison of Three Bed Bug Management Strategies in a Low-Income Apartment Building

PubMed Central

Wang, Changlu; Saltzmann, Kurt; Bennett, Gary; Gibb, Timothy

2012-01-01

Bed bug (Cimex lectularius L.) infestations are currently controlled by a variety of non-chemical and chemical methods. There have been few studies on the comparative effectiveness of these control techniques. We evaluated three bed bug management strategies in an apartment building: (1) non-chemical methods only (n = 9); (2) insecticides only (n = 6); and (3) integrated pest management including both non-chemical methods and insecticides (n = 9). The apartments were one-bedroom units occupied by seniors or people with disabilities. Bed bug numbers in each apartment were determined by visual inspection and/or installing intercepting devices under bed and sofa legs. The median (min, max) bed bug counts in the non-chemical methods only, insecticides only, and integrated pest management (IPM) treatment were: 4 (1, 57), 19 (1, 250), and 14 (1, 219), respectively prior to the treatments. The apartments were retreated if found necessary during biweekly to monthly inspections. After 10 weeks, bed bugs were found to be eliminated from 67, 33, and 44% of the apartments in the three treatment groups, respectively. The final (after 10 weeks) median (min, max) bed bug counts in the non-chemical methods only, insecticides only, and IPM treatment were: 0 (0, 134), 11.5 (0, 58), and 1 (0, 38), respectively. There were no significant differences in the speed of bed bug count reduction or the final bed bug counts. Lack of resident cooperation partially contributed to the failure in eliminating bed bugs from some of the apartments. Results of this study suggest that non-chemical methods can effectively eliminate bed bugs in lightly infested apartments. PMID:26466533

Molecular Basis of N,N-Diethyl-3-Methylbenzamide (DEET) in Repelling the Common Bed Bug, Cimex lectularius

PubMed Central

Liu, Feng; Xia, Xiaoming; Liu, Nannan

2017-01-01

As the most extensively used chemical repellent, N,N-diethyl-3-methylbenzamide (DEET) displayed repellency to a wide range of insects, including the common bed bug, Cimex lectularius. While the neuronal or molecular basis involved in DEET's repellency have been majorly focused on mosquitos and fruit flies, DEET's repellency to the common bed bug is largely unreached. To gain new insights into the cellular and molecular mechanisms in DEET's repellency to the common bed bug, we characterized the neuronal response of bed bugs to DEET, identified the olfactory receptors targeted by DEET and demonstrated the interfering effect of DEET on bed bug's responses to human odorants. High doses of DEET were required for activating the olfactory receptor neurons in the sensilla of bed bugs and at least three DEET-sensitive receptors were functionally deciphered. These DEET-sensitive receptors presented even more sensitive to certain botanical terpenes/terpenoids which also displayed repellency at varying levels for bed bugs. In addition, DEET produced a blocking effect on the neuronal responses of bed bugs to specific human odors and showed inhibitory effect on the function of odorant receptors in responding to certain human odors. Taken together, our results indicate that DEET may function as a stimulus that triggers avoidance behaviors and a molecular “confusant” for interrupting the host odor recognition in the odorant receptors of bed bugs. The receptors that coincidently responded to both synthetic DEET and botanical terpenes/terpenoids suggested that DEET probably target on receptors that originally responded to terpenes/terpenoids. This study gave novel insight into the mechanisms of DEET's repellency to bed bugs and also provided valuable information for developing new reagents for bed bug control. PMID:28676765

The importance of education to increase the use of bed nets in villages outside of Kinshasa, Democratic Republic of the Congo.

PubMed

Ndjinga, Julie K; Minakawa, Noboru

2010-10-12

Malaria is the most prominent disease in the Democratic Republic of the Congo (DRC), and long-lasting insecticide-treated nets (LLINs) have been distributed free of charge since 2006 to combat the disease. However, the success of this bed net campaign depends on sufficient bed net use in all age groups. This study was designed to examine the factors affecting bed net use in villages outside of Kinshasa. Two villages along the Congo River, totalling 142 households with 640 residents, were surveyed using a standard questionnaire. The interview determined the number, ages, and sexes of family members; the education level of the family head; the number, colour, and type of nets owned; and the number of nets used in the previous night. The size of house was also measured, and numbers of rooms and beds were recorded. These variables were examined to reveal important factors that affect bed net use. A total of 469 nets were counted, and nearly all nets were white LLINs. Of these nets, 229 (48.8%) nets were used by 284 (44.4%) residents. Bed nets were used by over 90% of children 5 to 15 years of age, whereas less than 50% of the residents in other age groups used bed nets. The important variables affecting bed net use were numbers of beds and rooms in the house and the education level of the family head of household. Education was the most important factor affecting bed net use in the villages outside Kinshasa. Development of an educational programme, particularly one directed toward parents, is necessary to reduce misconceptions and increase prevalence of bed net use among all age groups.

Channel responses to varying sediment input: A flume experiment modeled after Redwood Creek, California

USGS Publications Warehouse

Madej, Mary Ann; Sutherland, D.G.; Lisle, T.E.; Pryor, B.

2009-01-01

At the reach scale, a channel adjusts to sediment supply and flow through mutual interactions among channel form, bed particle size, and flow dynamics that govern river bed mobility. Sediment can impair the beneficial uses of a river, but the timescales for studying recovery following high sediment loading in the field setting make flume experiments appealing. We use a flume experiment, coupled with field measurements in a gravel-bed river, to explore sediment transport, storage, and mobility relations under various sediment supply conditions. Our flume experiment modeled adjustments of channel morphology, slope, and armoring in a gravel-bed channel. Under moderate sediment increases, channel bed elevation increased and sediment output increased, but channel planform remained similar to pre-feed conditions. During the following degradational cycle, most of the excess sediment was evacuated from the flume and the bed became armored. Under high sediment feed, channel bed elevation increased, the bed became smoother, mid-channel bars and bedload sheets formed, and water surface slope increased. Concurrently, output increased and became more poorly sorted. During the last degradational cycle, the channel became armored and channel incision ceased before all excess sediment was removed. Selective transport of finer material was evident throughout the aggradational cycles and became more pronounced during degradational cycles as the bed became armored. Our flume results of changes in bed elevation, sediment storage, channel morphology, and bed texture parallel those from field surveys of Redwood Creek, northern California, which has exhibited channel bed degradation for 30??years following a large aggradation event in the 1970s. The flume experiment suggested that channel recovery in terms of reestablishing a specific morphology may not occur, but the channel may return to a state of balancing sediment supply and transport capacity.

Sedimentological analysis and bed thickness statistics from a Carboniferous deep-water channel-levee complex: Myall Trough, SE Australia

NASA Astrophysics Data System (ADS)

Palozzi, Jason; Pantopoulos, George; Maravelis, Angelos G.; Nordsvan, Adam; Zelilidis, Avraam

2018-02-01

This investigation presents an outcrop-based integrated study of internal division analysis and statistical treatment of turbidite bed thickness applied to a Carboniferous deep-water channel-levee complex in the Myall Trough, southeast Australia. Turbidite beds of the studied succession are characterized by a range of sedimentary structures grouped into two main associations, a thick-bedded and a thin-bedded one, that reflect channel-fill and overbank/levee deposits, respectively. Three vertically stacked channel-levee cycles have been identified. Results of statistical analysis of bed thickness, grain-size and internal division patterns applied on the studied channel-levee succession, indicate that turbidite bed thickness data seem to be well characterized by a bimodal lognormal distribution, which is possibly reflecting the difference between deposition from lower-density flows (in a levee/overbank setting) and very high-density flows (in a channel fill setting). Power law and exponential distributions were observed to hold only for the thick-bedded parts of the succession and cannot characterize the whole bed thickness range of the studied sediments. The succession also exhibits non-random clustering of bed thickness and grain-size measurements. The studied sediments are also characterized by the presence of statistically detected fining-upward sandstone packets. A novel quantitative approach (change-point analysis) is proposed for the detection of those packets. Markov permutation statistics also revealed the existence of order in the alternation of internal divisions in the succession expressed by an optimal internal division cycle reflecting two main types of gravity flow events deposited within both thick-bedded conglomeratic and thin-bedded sandstone associations. The analytical methods presented in this study can be used as additional tools for quantitative analysis and recognition of depositional environments in hydrocarbon-bearing research of ancient deep-water channel-levee settings.

Binge-eating disorder in the Swedish national registers: Somatic comorbidity.

PubMed

Thornton, Laura M; Watson, Hunna J; Jangmo, Andreas; Welch, Elisabeth; Wiklund, Camilla; von Hausswolff-Juhlin, Yvonne; Norring, Claes; Herman, Barry K; Larsson, Henrik; Bulik, Cynthia M

2017-01-01

To evaluate associations between binge-eating disorder (BED) and somatic illnesses and determine whether medical comorbidities are more common in individuals who present with BED and comorbid obesity. Cases (n = 850) were individuals with a BED diagnosis in the Swedish eating disorders quality registers. Ten community controls were matched to each case on sex, and year, month, and county of birth. Associations of BED status with neurologic, immune, respiratory, gastrointestinal, skin, musculoskeletal, genitourinary, circulatory, and endocrine system diseases were evaluated using conditional logistic regression models. We further examined these associations by adjusting for lifetime psychiatric comorbidity. Amongst individuals with BED, we explored whether comorbid obesity was associated with risk of somatic disorders. BED was associated with most classes of diseases evaluated; strongest associations were with diabetes [odds ratio (95% confidence interval) = 5.7 (3.8; 8.7)] and circulatory systems [1.9 (1.3; 2.7)], likely indexing components of metabolic syndrome. Amongst individuals with BED, those with comorbid obesity were more likely to have a lifetime history of respiratory [1.5 (1.1; 2.1)] and gastrointestinal [2.6 (1.7; 4.1)] diseases than those without comorbid obesity. Increased risk of some somatic disease classes in individuals with BED was not simply due to obesity or other lifetime psychiatric comorbidity. The association of BED with many somatic illnesses highlights the morbidity experienced by individuals with BED. Clinicians treating patients with BED should be vigilant for medical comorbidities. Nonpsychiatric providers may be the first clinical contact for those with BED underscoring the importance of screening in primary care. © 2016 The Authors International Journal of Eating Disorders Published by Wiley Periodicals, Inc. (Int J Eat Disord 2017; 50:58-65). © 2016 The Authors International Journal of Eating Disorders Published by Wiley Periodicals, Inc.

Characteristics and use of treatment modalities of patients with binge-eating disorder in the Department of Veterans Affairs.

PubMed

Bellows, Brandon K; DuVall, Scott L; Kamauu, Aaron W C; Supina, Dylan; Pawaskar, Manjiri; Babcock, Thomas; LaFleur, Joanne

2016-04-01

In 2013 binge-eating disorder (BED) was recognized as a formal diagnosis, but was historically included under the diagnosis code for eating disorder not otherwise specified (EDNOS). This study compared the characteristics and use of treatment modalities in BED patients to those with EDNOS without BED (EDNOS-only) and to matched-patients with no eating disorders (NED). Patients were identified for this study from electronic health records in the Department of Veterans Affairs from 2000 to 2011. Patients with BED were identified using natural language processing and patients with EDNOS-only were identified by ICD-9 code (307.50). First diagnosis defined index date for these groups. NED patients were frequency matched to BED patients up to 4:1, as available, on age, sex, BMI, depression, and index month encounter. Baseline characteristics and use of treatment modalities during the post-index year were compared using t-tests or chi-square tests. There were 593 BED, 1354 EDNOS-only, and 1895 matched-NED patients identified. Only 68 patients with BED had an EDNOS diagnosis. BED patients were younger (48.7 vs. 49.8years, p=0.04), more were male (72.2% vs. 62.8%, p<0.001) and obese (BMI 40.2 vs. 37.0, p<0.001) than EDNOS-only patients. In the follow-up period fewer BED (68.0%) than EDNOS-only patients (87.6%, p<0.001), but more BED than NED patients (51.9%, p<0.001) used at least one treatment modality. The characteristics of BED patients were different from those with EDNOS-only and NED as was their use of treatment modalities. These differences highlight the need for a separate identifier of BED. Copyright © 2016 Elsevier Ltd. All rights reserved.

The varying stability of benthic homes: hydrologic regime and sediment supply control the timing and intensity of bed mobility

NASA Astrophysics Data System (ADS)

Pfeiffer, A.; Finnegan, N. J.

2017-12-01

Gravel river beds provide an ephemeral architecture for the benthic inhabitants of river ecosystems. Periphyton and benthic macroinvertebrates that live on or within the gravel are subject to catastrophic disruption upon mobilization of the surface gravel during floods. Because sediment supply varies by orders of magnitude across North America, and rivers have adjusted to convey their imposed loads, river bed surface mobility varies enormously. Climate also varies widely across the continent, yielding a range of flood timing, duration, and intermittency. Together, the differences in sediment supply and hydrologic patterns result in diverse regimes of benthic habitat stability. To quantitatively characterize these regimes, we calculate decades-scale time series of estimated bed surface mobility using sediment transport equations (Wilcock and Crowe, 2003). The method requires measurements of the bed surface grainsize distribution, channel slope, and standard USGS stream gauging records. We calculate the fraction of the bed surface grain size distribution that is mobile at any given flow, as well as the intensity of transport. We use the time series of bed mobility to compare between rivers and regions. In many snowmelt-dominated rivers in Idaho, a period of moderate bed mobility (W* > 0.002) generally occurs during the annual melt, and can last for days. In rivers draining the central and northern Appalachians, bed mobility is comparatively rare and occurs during short duration floods. Rivers on the tectonically active West Coast tend to experience bed mobility during most winter storms, with brief (hours long) periods of high transport rates (W* > 0.02) during storm peaks. The timing and intensity of bed mobility varies with hydrologic regime and sediment supply; these contrasts in bed mobility lead to diverse structural templates for river ecosystems.

Experimental investigation of the strength and failure behavior of layered sandstone under uniaxial compression and Brazilian testing

NASA Astrophysics Data System (ADS)

Yin, Peng-Fei; Yang, Sheng-Qi

2018-05-01

As a typical inherently anisotropic rock, layered sandstones can differ from each other in several aspects, including grain size, type of material, type of cementation, and degree of compaction. An experimental study is essential to obtain and convictive evidence to characterize the mechanical behavior of such rock. In this paper, the mechanical behavior of a layered sandstone from Xuzhou, China, is investigated under uniaxial compression and Brazilian test conditions. The loading tests are conducted on 7 sets of bedding inclinations, which are defined as the angle between the bedding plane and horizontal direction. The uniaxial compression strength (UCS) and elastic modulus values show an undulatory variation when the bedding inclination increases. The overall trend of the UCS and elastic modulus values with bedding inclination is decreasing. The BTS value decreases with respect to the bedding inclination and the overall trend of it is approximating a linear variation. The 3D digital high-speed camera images reveal that the failure and fracture of a specimen are related to the surface deformation. Layered sandstone tested under uniaxial compression does not show a typical failure mode, although shear slip along the bedding plane occurs at high bedding inclinations. Strain gauge readings during the Brazilian tests indicate that the normal stress on the bedding plane transforms from compression to tension as the bedding inclination increases. The stress parallel to the bedding plane in a rock material transforms from tension to compression and agrees well with the fracture patterns; "central fractures" occur at bedding inclinations of 0°-75°, "layer activation" occurs at high bedding inclinations of 75°-90°, and a combination of the two occurs at 75°.

What is a hospital bed day worth? A contingent valuation study of hospital Chief Executive Officers.

PubMed

Page, Katie; Barnett, Adrain G; Graves, Nicholas

2017-02-14

Decreasing hospital length of stay, and so freeing up hospital beds, represents an important cost saving which is often used in economic evaluations. The savings need to be accurately quantified in order to make optimal health care resource allocation decisions. Traditionally the accounting cost of a bed is used. We argue instead that the economic cost of a bed day is the better value for making resource decisions, and we describe our valuation method and estimations for costing this important resource. We performed a contingent valuation using 37 Australian Chief Executive Officers' (CEOs) willingness to pay (WTP) to release bed days in their hospitals, both generally and using specific cases. We provide a succinct thematic analysis from qualitative interviews post survey completion, which provide insight into the decision making process. On average CEOs are willing to pay a marginal rate of $216 for a ward bed day and $436 for an Intensive Care Unit (ICU) bed day, with estimates of uncertainty being greater for ICU beds. These estimates are significantly lower (four times for ward beds and seven times for ICU beds) than the traditional accounting costs often used. Key themes to emerge from the interviews include the importance of national funding and targets, and their associated incentive structures, as well as the aversion to discuss bed days as an economic resource. This study highlights the importance for valuing bed days as an economic resource to inform cost effectiveness models and thus improve hospital decision making and resource allocation. Significantly under or over valuing the resource is very likely to result in sub-optimal decision making. We discuss the importance of recognising the opportunity costs of this resource and highlight areas for future research.

Method of feeding particulate material to a fluidized bed

DOEpatents

Borio, Richard W.; Goodstine, Stephen L.

1984-01-01

A centrifugal spreader type feeder that supplies a mixture of particulate limestone and coal to the top of a fluidized bed reactor having a flow of air upward therethrough. Large particles of particulate matter are distributed over the upper surface of the bed to utilize the natural mixing within the bed, while fine particles are adapted to utilize an independent feeder that separates them from the large particles and injects them into the bed.

Bacterial counts on teat skin and in new sand, recycled sand, and recycled manure solids used as bedding in freestalls.

PubMed

Rowbotham, R F; Ruegg, P L

2016-08-01

On modern dairy farms, environmental mastitis pathogens are usually the predominant cause of mastitis, and bedding often serves as a point of exposure to these organisms. The objective of this longitudinal study was to determine bacterial populations of 4 different bedding types [deep-bedded new sand (NES), deep-bedded recycled sand (RS), deep-bedded manure solids (DBMS), and shallow-bedded manure solids over foam core mattresses (SBMS)] and of teat skin swabs of primarily primiparous cows housed in a single facility over all 4 seasons. Samples of bedding were collected weekly (n=49wk) from pens that each contained 32 lactating dairy cows. Throughout the length of the same period, composite swabs of teat skin were collected weekly from all cows before and after premilking teat sanitation. Median numbers of streptococci and streptococci-like organisms (SSLO) were >8.6×10(6) cfu/g and >6.9×10(3) cfu/teat swab for all bedding types and teat swabs, respectively. Numbers of SSLO were greatest in samples of SBMS (2.1×10(8) cfu/g) and least in samples of NES (8.6×10(6) cfu/g), RS (1.3×10(7) cfu/g), and DBMS (1.7×10(7) cfu/g). Numbers of gram-negative bacteria in bedding (5.5×10(4) to 1.2×10(7) cfu/g) were fewer than numbers of SSLO (8.6×10(6) to 2.1×10(8) cfu/g). Numbers of coliform bacteria were greatest in samples of DBMS (2.2×10(6) cfu/g) and least in samples of NES (3.6×10(3) cfu/g). In general, the relative number of bacteria on teat skin corresponded to exposure in bedding. Numbers of gram-negative bacteria recovered from prepreparation teat swabs were greatest for cows bedded with DBMS (1.0×10(4) cfu/swab) and RS (2.5×10(3) cfu/swab) and least for cows bedded with NES (5.8×10(2) cfu/swab). Median numbers of coliform and Klebsiella spp. recovered from prepreparation teat swabs were below the limit of detection for all cows except those bedded with DBMS. Numbers of SSLO recovered from prepreparation teat swabs were least for cows bedded with DBMS (6.9×10(3) cfu/swab) and greatest for cows bedded with RS (5.1×10(4) cfu/swab) or SBMS (1.6×10(5) cfu/swab). The numbers of all types of measured bacteria (total gram-negative, coliforms, Klebsiella spp., SSLO) on postpreparation teat swabs were reduced by up to 2.6 logs from numbers of bacteria on prepreparation swabs, verifying effective preparation procedures. Significant correlations between bacterial counts of bedding samples and teat skin swabs were observed for several types of bacteria. As compared with other bedding types, the least amount of gram-negative bacteria were recovered from NES and may indicate that cows on NES have a reduced risk of exposure to pathogens that are typically a cause of clinical mastitis. In contrast, exposure to large numbers of SSLO was consistent across all bedding types and may indicate that risk of subclinical mastitis typically associated with streptococci is not as influenced by bedding type; however, significantly greater numbers of SSLO were found in SBMS than in other bedding types. These findings indicate that use of different bedding types results in exposure to different distributions of mastitis pathogens that may alter the proportion of etiologies of clinical mastitis, although the incidence rate of clinical mastitis did not differ among bedding types. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Effects of sawdust bedding dry matter on lying behavior of dairy cows: a dose-dependent response.

PubMed

Reich, L J; Weary, D M; Veira, D M; von Keyserlingk, M A G

2010-04-01

The objective was to determine the effect of sawdust bedding dry matter on the lying behavior of Holstein cows. Dry matter (DM) was varied systematically over 5 treatment levels to test how cows respond to damp bedding. This experiment was repeated during summer and winter to test if the effects of damp bedding varied with season. The 5 bedding treatments averaged (+/-SD) 89.8+/-3.7, 74.2+/-6.4, 62.2+/-6.3, 43.9+/-4.0, and 34.7+/-3.8% DM. Over the course of the trial, minimum and maximum temperatures in the barn were 2.6+/-2.0 and 6.8+/-2.2 degrees C in the winter and 13.3+/-2.5 and 22.6+/-4.1 degrees C in the summer. In both seasons, 5 groups of 3 nonlactating cows were housed in free stalls bedded with sawdust. Following a 5-d acclimation period on dry bedding, groups were exposed to the 5 bedding treatments in a 5 x 5 Latin square. Each treatment lasted 4 d, followed by 1 d when the cows were provided with dry bedding. Stall usage was assessed by 24-h video scanned at 5-min intervals. Responses were analyzed within group (n=5) as the observational unit. Bedding DM affected lying time, averaging 10.4+/-0.4 h/d on the wettest treatment and increasing to 11.5+/-0.4 h/d on the driest bedding. Lying time varied with season, averaging 12.1+/-0.4 h/d across treatments during the winter and 9.9+/-0.6 h/d during the summer, but season and bedding DM did not interact. These results indicate that access to dry bedding is important for dairy cows. Copyright (c) 2010 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

The Odorant Receptor Co-Receptor from the Bed Bug, Cimex lectularius L

PubMed Central

Hansen, Immo A.; Rodriguez, Stacy D.; Drake, Lisa L.; Price, David P.; Blakely, Brittny N.; Hammond, John I.; Tsujimoto, Hitoshi; Monroy, Erika Y.; Maio, William A.; Romero, Alvaro

2014-01-01

Recently, the bed bug, Cimex lectularius L. has re-emerged as a serious and growing problem in many parts of the world. Presence of resistant bed bugs and the difficulty to eliminate them has renewed interest in alternative control tactics. Similar to other haematophagous arthropods, bed bugs rely on their olfactory system to detect semiochemicals in the environment. Previous studies have morphologically characterized olfactory organs of bed bugs’ antenna and have physiologically evaluated the responses of olfactory receptor neurons (ORNs) to host-derived chemicals. To date, odorant binding proteins (OBPs) and odorant receptors (ORs) associated with these olfaction processes have not been studied in bed bugs. Chemoreception in insects requires formation of heteromeric complexes of ORs and a universal OR coreceptor (Orco). Orco is the constant chain of every odorant receptor in insects and is critical for insect olfaction but does not directly bind to odorants. Orco agonists and antagonists have been suggested as high-value targets for the development of novel insect repellents. In this study, we have performed RNAseq of bed bug sensory organs and identified several odorant receptors as well as Orco. We characterized Orco expression and investigated the effect of chemicals targeting Orco on bed bug behavior and reproduction. We have identified partial cDNAs of six C. lectularius OBPs and 16 ORs. Full length bed bug Orco was cloned and sequenced. Orco is widely expressed in different parts of the bed bug including OR neurons and spermatozoa. Treatment of bed bugs with the agonist VUAA1 changed bed bug pheromone-induced aggregation behavior and inactivated spermatozoa. We have described and characterized for the first time OBPs, ORs and Orco in bed bugs. Given the importance of these molecules in chemoreception of this insect they are interesting targets for the development of novel insect behavior modifiers. PMID:25411789

Effectiveness of bed bug monitors for detecting and trapping bed bugs in apartments.

PubMed

Wang, Changlu; Tsai, Wan-Tien; Cooper, Richard; White, Jeffrey

2011-02-01

Bed bugs, Cimex lectularius L., are now considered a serious urban pest in the United States. Because they are small and difficult to find, there has been strong interest in developing and using monitoring tools to detect bed bugs and evaluate the results of bed bug control efforts. Several bed bug monitoring devices were developed recently, but their effectiveness is unknown. We comparatively evaluated three active monitors that contain attractants: CDC3000, NightWatch, and a home-made dry ice trap. The Climbup Insect Interceptor, a passive monitor (without attractants), was used for estimating the bed bug numbers before and after placing active monitors. The results of the Interceptors also were compared with the results of the active monitors. In occupied apartments, the relative effectiveness of the active monitors was: dry ice trap > CDC3000 > NightWatch. In lightly infested apartments, the Interceptor (operated for 7 d) trapped similar number of bed bugs as the dry ice trap (operated for 1 d) and trapped more bed bugs than CDC3000 and NightWatch (operated for 1 d). The Interceptor was also more effective than visual inspections in detecting the presence of small numbers of bed bugs. CDC3000 and the dry ice trap operated for 1 d were equally as effective as the visual inspections for detecting very low level of infestations, whereas 1-d deployment of NightWatch detected significantly lower number of infestations compared with visual inspections. NightWatch was designed to be able to operate for several consecutive nights. When operated for four nights, NightWatch trapped similar number of bed bugs as the Interceptors operated for 10 d after deployment of NightWatch. We conclude these monitors are effective tools in detecting early bed bug infestations and evaluating the results of bed bug control programs.

The odorant receptor co-receptor from the bed bug, Cimex lectularius L.

PubMed

Hansen, Immo A; Rodriguez, Stacy D; Drake, Lisa L; Price, David P; Blakely, Brittny N; Hammond, John I; Tsujimoto, Hitoshi; Monroy, Erika Y; Maio, William A; Romero, Alvaro

2014-01-01

Recently, the bed bug, Cimex lectularius L. has re-emerged as a serious and growing problem in many parts of the world. Presence of resistant bed bugs and the difficulty to eliminate them has renewed interest in alternative control tactics. Similar to other haematophagous arthropods, bed bugs rely on their olfactory system to detect semiochemicals in the environment. Previous studies have morphologically characterized olfactory organs of bed bugs' antenna and have physiologically evaluated the responses of olfactory receptor neurons (ORNs) to host-derived chemicals. To date, odorant binding proteins (OBPs) and odorant receptors (ORs) associated with these olfaction processes have not been studied in bed bugs. Chemoreception in insects requires formation of heteromeric complexes of ORs and a universal OR coreceptor (Orco). Orco is the constant chain of every odorant receptor in insects and is critical for insect olfaction but does not directly bind to odorants. Orco agonists and antagonists have been suggested as high-value targets for the development of novel insect repellents. In this study, we have performed RNAseq of bed bug sensory organs and identified several odorant receptors as well as Orco. We characterized Orco expression and investigated the effect of chemicals targeting Orco on bed bug behavior and reproduction. We have identified partial cDNAs of six C. lectularius OBPs and 16 ORs. Full length bed bug Orco was cloned and sequenced. Orco is widely expressed in different parts of the bed bug including OR neurons and spermatozoa. Treatment of bed bugs with the agonist VUAA1 changed bed bug pheromone-induced aggregation behavior and inactivated spermatozoa. We have described and characterized for the first time OBPs, ORs and Orco in bed bugs. Given the importance of these molecules in chemoreception of this insect they are interesting targets for the development of novel insect behavior modifiers.

Revised Lithostratigraphy of the Sonsela Member (Chinle Formation, Upper Triassic) in the Southern Part of Petrified Forest National Park, Arizona

PubMed Central

Martz, Jeffrey W.; Parker, William G.

2010-01-01

Background Recent revisions to the Sonsela Member of the Chinle Formation in Petrified Forest National Park have presented a three-part lithostratigraphic model based on unconventional correlations of sandstone beds. As a vertebrate faunal transition is recorded within this stratigraphic interval, these correlations, and the purported existence of a depositional hiatus (the Tr-4 unconformity) at about the same level, must be carefully re-examined. Methodology/Principal Findings Our investigations demonstrate the neglected necessity of walking out contacts and mapping when constructing lithostratigraphic models, and providing UTM coordinates and labeled photographs for all measured sections. We correct correlation errors within the Sonsela Member, demonstrate that there are multiple Flattops One sandstones, all of which are higher than the traditional Sonsela sandstone bed, that the Sonsela sandstone bed and Rainbow Forest Bed are equivalent, that the Rainbow Forest Bed is higher than the sandstones at the base of Blue Mesa and Agate Mesa, that strata formerly assigned to the Jim Camp Wash beds occur at two stratigraphic levels, and that there are multiple persistent silcrete horizons within the Sonsela Member. Conclusions/Significance We present a revised five-part model for the Sonsela Member. The units from lowest to highest are: the Camp Butte beds, Lot's Wife beds, Jasper Forest bed (the Sonsela sandstone)/Rainbow Forest Bed, Jim Camp Wash beds, and Martha's Butte beds (including the Flattops One sandstones). Although there are numerous degradational/aggradational cycles within the Chinle Formation, a single unconformable horizon within or at the base of the Sonsela Member that can be traced across the entire western United States (the “Tr-4 unconformity”) probably does not exist. The shift from relatively humid and poorly-drained to arid and well-drained climatic conditions began during deposition of the Sonsela Member (low in the Jim Camp Wash beds), well after the Carnian-Norian transition. PMID:20174475

Operating characteristics of residential care communities, by community bed size: United States, 2012.

PubMed

Caffrey, Christine; Harris-Kojetin, Lauren; Rome, Vincent; Sengupta, Manisha

2014-11-01

In 2012, the majority of residential care communities had 4–25 beds, yet 71% of residents lived in communities with more than 50 beds. A lower percentage of communities with 4–25 beds were chain-affiliated, nonprofit, and in operation 10 years or more, compared with communities with 26–50 and more than 50 beds. Dementia-exclusive care or dementia care units were more common as community size increased. A higher percentage of communities with more than 50 beds screened for cognitive impairment and offered dementia-specific programming compared with communities with 4–25 and 26–50 beds. A higher percentage of communities with more than 50 beds screened for depression compared with communities with 4–25 beds. Compared with communities with 4–25 beds, a higher percentage of communities with 26–50 beds and more than 50 beds provided therapeutic, hospice, mental health, and dental services; but a lower percentage of communities with more than 50 beds provided skilled nursing services than did smaller communities. This report presents national estimates of residential care communities, using data from the first wave of NSLTCP. This brief profile of residential care communities provides useful information to policymakers, providers, researchers, and consumer advocates as they plan to meet the needs of an aging population. The findings also highlight the diversity of residential care communities across different sizes. Corresponding state estimates and their standard errors for the national figures in this data brief can be found on the NSLTCP website at http://www.cdc.gov/nchs/nsltcp/ nsltcp_products.htm. These national and state estimates establish a baseline for monitoring trends among residents living in residential care. All material appearing in this report is in the public domain and may be reproduced or copied without permission; citation as to source, however, is appreciated.

A Discrete Event Simulation Model of Patient Flow in a General Hospital Incorporating Infection Control Policy for Methicillin-Resistant Staphylococcus Aureus (MRSA) and Vancomycin-Resistant Enterococcus (VRE).

PubMed

Shenoy, Erica S; Lee, Hang; Ryan, Erin E; Hou, Taige; Walensky, Rochelle P; Ware, Winston; Hooper, David C

2018-02-01

Hospitalized patients are assigned to available staffed beds based on patient acuity and services required. In hospitals with double-occupancy rooms, patients must be additionally matched by gender. Patients with methicillin-resistant Staphylococcus aureus (MRSA) or vancomycin-resistant Enterococcus (VRE) must be bedded in single-occupancy rooms or cohorted with other patients with similar MRSA/VRE flags. We developed a discrete event simulation (DES) model of patient flow through an acute care hospital. Patients are matched to beds based on acuity, service, gender, and known MRSA/VRE colonization. Outcomes included time to bed arrival, length of stay, patient-bed acuity mismatches, occupancy, idle beds, acuity-related transfers, rooms with discordant MRSA/VRE colonization, and transmission due to discordant colonization. Observed outcomes were well-approximated by model-generated outcomes for time-to-bed arrival (6.7 v. 6.2 to 6.5 h) and length of stay (3.3 v. 2.9 to 3.0 days), with overlapping 90% coverage intervals. Patient-bed acuity mismatches, where patient acuity exceeded bed acuity and where patient acuity was lower than bed acuity, ranged from 0.6 to 0.9 and 8.6 to 11.1 mismatches per h, respectively. Values for observed occupancy, total idle beds, and acuity-related transfers compared favorably to model-predicted values (91% v. 86% to 87% occupancy, 15.1 v. 14.3 to 15.7 total idle beds, and 27.2 v. 22.6 to 23.7 transfers). Rooms with discordant colonization status and transmission due to discordance were modeled without an observed value for comparison. One-way and multi-way sensitivity analyses were performed for idle beds and rooms with discordant colonization. We developed and validated a DES model of patient flow incorporating MRSA/VRE flags. The model allowed for quantification of the substantial impact of MRSA/VRE flags on hospital efficiency and potentially avoidable nosocomial transmission.

Coupling scales for modelling heavy metal vaporization from municipal solid waste incineration in a fluid bed by CFD

DOE Office of Scientific and Technical Information (OSTI.GOV)

Soria, José, E-mail: jose.soria@probien.gob.ar; Gauthier, Daniel; Flamant, Gilles

2015-09-15

Highlights: • A CFD two-scale model is formulated to simulate heavy metal vaporization from waste incineration in fluidized beds. • MSW particle is modelled with the macroscopic particle model. • Influence of bed dynamics on HM vaporization is included. • CFD predicted results agree well with experimental data reported in literature. • This approach may be helpful for fluidized bed reactor modelling purposes. - Abstract: Municipal Solid Waste Incineration (MSWI) in fluidized bed is a very interesting technology mainly due to high combustion efficiency, great flexibility for treating several types of waste fuels and reduction in pollutants emitted with themore » flue gas. However, there is a great concern with respect to the fate of heavy metals (HM) contained in MSW and their environmental impact. In this study, a coupled two-scale CFD model was developed for MSWI in a bubbling fluidized bed. It presents an original scheme that combines a single particle model and a global fluidized bed model in order to represent the HM vaporization during MSW combustion. Two of the most representative HM (Cd and Pb) with bed temperatures ranging between 923 and 1073 K have been considered. This new approach uses ANSYS FLUENT 14.0 as the modelling platform for the simulations along with a complete set of self-developed user-defined functions (UDFs). The simulation results are compared to the experimental data obtained previously by the research group in a lab-scale fluid bed incinerator. The comparison indicates that the proposed CFD model predicts well the evolution of the HM release for the bed temperatures analyzed. It shows that both bed temperature and bed dynamics have influence on the HM vaporization rate. It can be concluded that CFD is a rigorous tool that provides valuable information about HM vaporization and that the original two-scale simulation scheme adopted allows to better represent the actual particle behavior in a fluid bed incinerator.« less

Annual bed-elevation regime in the alluvial channel of Squamish River, southwestern British Columbia Canada

USGS Publications Warehouse

Stanford, S.D.; Seidl, M.A.; Ashley, G.M.

2000-01-01

The aim of this study is to examine the annual regime of channel scour and fill by monitoring bed-elevation changes in a reach of Squamish River in southwestern British Columbia, Canada. Sonar surveys of 13 river cross-sections in a sandy gravel-bed single-channel study reach were repeated biweekly over a full hydrologic year (1995/6). The survey results show that bedload movement occurs as waves or pulses forming bedwaves that appear to maintain an overall coherence with movement downstream. These bedwaves propagate downstream by a mode here termed pulse scour and pulse fill, a process distinguished from the conventional mode of scour and fill commonly associated with flood events (here termed local scour and local fill). Bedwave celerity was estimated to be about 15.5 m d-1 corresponding to a bedwave residence time in the study reach of almost one hydrologic year. The total amount of local bed-elevation change ranged between 0.22 m and 2.41 m during the period of study. Analysis of the bed-elevation and flow data reveals that, because of the bedware phenomenon, there is no simple relation between the mean bed-elevation and discharge nor any strong linear correlation among cross-sectional behaviour. The bed-elevation data also suggest that complex changes to the bed within a cross-section are masked when the bed is viewed in one dimension, although no definitive trends in bed behaviour were found in the two-dimensional analysis. Although a weak seasonal effect is evident in this study, the bed-elevation regime is dominated by sediment supply-driven fluctuations in bedload transport occurring at timescales shorter than the seasonal fluctuation in discharge. The study also indicates that bed-elevation monitoring on Squamish River, and others like it, for purposes of detecting and measuring aggradation/degradation must take into account very considerable and normal channel-bed variability operating at timescales from hours to months. Copyright (C) 2000 John Wiley and Sons, Ltd.

Seagrass distribution and abundance in Eastern Gulf of Mexico coastal waters

NASA Astrophysics Data System (ADS)

Iverson, Richard L.; Bittaker, Henry F.

1986-05-01

The marine angiosperms Thalassia testudinum, Syringodium filiforme, and Halodule wrightii form two of the largest reported seagrass beds along the northwest and southern coasts of Florida where they cover about 3000 square km in the Big Bend area and about 5500 square km in Florida Bay, respectively. Most of the leaf biomass in the Big Bend area and outer Florida Bay was composed of Thalassia testudinum and Syringodium filiforme which were distributed throughout the beds but which were more abundant in shallow depths. A short-leaved form of Halodule wrightii grew in monotypic stands in shallow water near the inner edges of the beds, while Halophila decipiens and a longer-leaved variety of H. wrightii grew scattered throughout the beds, in monotypic stands near the outer edges of the beds, and in deeper water outside the beds. Halophila engelmanni was observed scattered at various depths throughout the seagrass beds and in monospecific patches in deep water outside the northern bed. Ruppia maritima grew primarily in brackish water around river mouths. The cross-shelf limits of the two major seagrass beds are controlled nearshore by increased water turbidity and lower salinity around river mouths and off-shore by light penetration to depths which receive 10% or more of sea surface photosynthetically active radiation. Seagrasses form large beds only along low energy reaches of the coast. The Florida Bay seagrass bed contained about twice the short-shoot density of both Thalassia testudinum and Syringodium filiforme, for data averaged over all depths, and about four times the average short-shoot density of both species in shallow water compared with the Big Bend seagrass bed. The differences in average seagrass abundance between Florida Bay and the Big Bend area may be a consequence of the effects of greater seasonal solar radiation and water temperature fluctuations experienced by plants in the northern bed, which lies at the northern distribution limit for American Tropical seagrasses.

Geologic and physiographic controls on bed-material yield, transport, and channel morphology for alluvial and bedrock rivers, western Oregon

NASA Astrophysics Data System (ADS)

O'Connor, J. E.; Wallick, R.; Mangano, J.; Anderson, S. W.; Jones, K. L.; Keith, M. K.

2012-12-01

The rivers of western Oregon have channel beds ranging from fully alluvial to bedrock. A local history of in-stream gravel mining in conjunction with ongoing permitting concerns with respect to future extraction have prompted a series of investigations of bed-material production, transport and channel morphology across this spectrum of channel types. In western Oregon, it appears that the distribution of alluvial and bedrock channels (and many aspects of river morphology and behavior) are largely controlled by regional lithologies and the downstream consequences of different rates of bed-material supply and clast comminution. In particular, the Klamath Terrane has elevated erosion rates, steep slopes, and rock types resistant to abrasion, resulting in gravel-bed alluvial channels with high bed-material transport rates. By contrast, Coast Range drainages underlain by large areas of soft sedimentary rocks have bedrock channels owing to exceptionally rapid rates of bed-material attrition during transport. The resulting spatially distributed network controls on the distribution of alluvial and non-alluvial channels likely complicate linkages between rock uplift, bedrock incision, bed-material grain size, and profile concavity. Additionally, the alluvial channels have distinct morphologic characteristics, some of which relate strongly to transport rates. In particular, bar area correlates with estimates of bed-material flux, and this correlation is an upper bound for bar-area observations for non-alluvial reaches. Similarly, an index for transport capacity scaled by bed-material grain size correlates with estimated bed-material flux for alluvial rivers, but not for the non-alluvial rivers. Bedrock and mixed-bed channels in western Oregon have few evident broad-scale patterns or relations among reach-scale morphologic measurements or with estimated transport rates, perhaps indicating that very local lithologic, hydraulic and bed-material supply conditions exert more control on channel morphology.

Geologic and physiographic controls on bed-material yield, transport, and channel morphology for alluvial and bedrock rivers, western Oregon

USGS Publications Warehouse

O'Connor, James E.; Mangano, Joseph F.; Anderson, Scott A.; Wallick, J. Rose; Jones, Krista L.; Keith, Mackenzie K.

2014-01-01

The rivers of western Oregon have diverse forms and characteristics, with channel substrates ranging from continuous alluvial gravel to bare bedrock. Analysis of several measurable morphologic attributes of 24 valley reaches on 17 rivers provides a basis for comparing nonalluvial and alluvial channels. Key differences are that alluvial reaches have greater bar area, greater migration rates, and show systematic correlation among variables relating grain size to bed-material transport capacity. We relate these differences between channel types to bed-material transport rates as derived from a coupled regional analysis of empirical sediment yield measurements and physical experiments of clast attrition during transport. This sediment supply analysis shows that overall bed-material transport rates for western Oregon are chiefly controlled by (1) lithology and basin slope, which are the key factors for bed-material supply into the stream network, and (2) lithologic control of bed-material attrition from in-transport abrasion and disintegration. This bed-material comminution strongly affects bed-material transport in the study area, reducing transport rates by 50%–90% along the length of the larger rivers in the study area. A comparison of the bed-material transport estimates with the morphologic analyses shows that alluvial gravel-bed channels have systematic and bounding relations between bed-material transport rate and attributes such as bar area and local transport capacity. By contrast, few such relations are evident for nonalluvial rivers with bedrock or mixed-bed substrates, which are apparently more influenced by local controls on channel geometry and sediment supply. At the scale of western Oregon, the physiographic and lithologic controls on the balance between bed-material supply and transport capacity exert far-reaching influence on the distribution of alluvial and nonalluvial channels and their consequently distinctive morphologies and behaviors—differences germane for understanding river response to tectonics and environmental perturbations, as well as for implementing effective restoration and monitoring strategies.

Use of bed nets and factors that influence bed net use among Jinuo Ethnic Minority in southern China.

PubMed

Xu, Jian-wei; Liao, Yuan-mei; Liu, Hui; Nie, Ren-hua; Havumaki, Joshua

2014-01-01

Insecticide-treated nets (ITNs) are an integral part of vector control recommendations for malaria elimination in China. This study investigated the extent to which bed nets were used and which factors influence bed net use among Jinuo Ethnic Minority in China-Myanmar-Laos border areas. This study combined a quantitative household questionnaire survey and qualitative semi-structured in-depth interviews (SDI). Questionnaires were administered to 352 heads of households. SDIs were given to 20 key informants. The bed net to person ratio was 1∶2.1 (i.e., nearly one net for every two people), however only 169 (48.0%) households owned at least one net and 623 (47.2%) residents slept under bed nets the prior night. The percentages of residents who regularly slept under nets (RSUN) and slept under nets the prior night (SUNPN) were similar (48.0% vs. 47.2%, P>0.05), however the percentage correct use of nets (CUN) was significantly lower (34.5%, P<0.0001). The annual cash income per person (ACIP) was an independent factor that influenced bed net use (P<0.0001), where families with an ACIP of CNY10000 or more were much more likely to use nets. House type was strongly associated with bed net use (OR: 4.71, 95% CI: 2.81, 7.91; P<0.0001), where those with traditional wood walls and terracotta roofs were significantly more likely to use nets, and the head of household's knowledge was an independent factor (OR: 5.04, 95% CI: 2.72, 9.35; P<0.0001), where those who knew bed nets prevent malaria were significantly more likely to use nets too. High bed net availability does not necessarily mean higher coverage or bed net use. Household income, house type and knowledge of the ability of bed nets to prevent malaria are all independent factors that influence bed net use among Jinuo Ethnic Minority.

Dermatology Residents are Prescribing Tanning Bed Treatment.

PubMed

Anderson, Kathryn L; Huang, Karen E; Huang, William W; Feldman, Steven R

2016-07-15

Although 90% of dermatologists discourage the use of tanning beds, about half of psoriasis patients report using tanning beds and most of these note improvement. The purpose of this investigation was to determine if dermatology residents are advocating the tanning bed use to their patients.

Heat-transfer characteristics of flowing and stationary particle-bed-type fusion-reactor blankets

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nietert, R.E.

1983-02-01

The following five appendices are included: (1) physical properties of materials, (2) thermal entrance length Nusselt number variations, (3) stationary particle bed temperature variations, (4) falling bed experimental data and calculations, and (5) stationary bed experimental data and calculations. (MOW)

Effect of 2 Bedding Materials on Ammonia Levels in Individually Ventilated Cages

PubMed Central

Koontz, Jason M; Kumsher, David M; III, Richard Kelly; Stallings, Jonathan D

2016-01-01

This study sought to identify an optimal rodent bedding and cage-change interval to establish standard procedures for the IVC in our rodent vivarium. Disposable cages were prefilled with either corncob or α-cellulose bedding and were used to house 2 adult Sprague–Dawley rats (experimental condition) or contained no animals (control). Rats were observed and intracage ammonia levels measured daily for 21 d. Intracage ammonia accumulation became significant by day 8 in experimental cages containing α-cellulose bedding, whereas experimental cages containing corncob bedding did not reach detectable levels of ammonia until day 14. In all 3 experimental cages containing α-cellulose, ammonia exceeded 100 ppm (our maximum acceptable limit) by day 11. Two experimental corncob cages required changing at days 16 and 17, whereas the remaining cage containing corncob bedding lasted the entire 21 d without reaching the 100-ppm ammonia threshold. These data suggests that corncob bedding provides nearly twice the service life of α-cellulose bedding in the IVC system. PMID:26817976

Recovery of nitrogen and light hydrocarbons from polyalkene purge gas

DOEpatents

Zwilling, Daniel Patrick; Golden, Timothy Christoph; Weist, Jr., Edward Landis; Ludwig, Keith Alan

2003-06-10

A method for the separation of a gas mixture comprises (a) obtaining a feed gas mixture comprising nitrogen and at least one hydrocarbon having two to six carbon atoms; (b) introducing the feed gas mixture at a temperature of about 60.degree. F. to about 105.degree. F. into an adsorbent bed containing adsorbent material which selectively adsorbs the hydrocarbon, and withdrawing from the adsorbent bed an effluent gas enriched in nitrogen; (c) discontinuing the flow of the feed gas mixture into the adsorbent bed and depressurizing the adsorbent bed by withdrawing depressurization gas therefrom; (d) purging the adsorbent bed by introducing a purge gas into the bed and withdrawing therefrom an effluent gas comprising the hydrocarbon, wherein the purge gas contains nitrogen at a concentration higher than that of the nitrogen in the feed gas mixture; (e) pressurizing the adsorbent bed by introducing pressurization gas into the bed; and (f) repeating (b) through (e) in a cyclic manner.

Effect of 2 Bedding Materials on Ammonia Levels in Individually Ventilated Cages.

PubMed

Koontz, Jason M; Kumsher, David M; Kelly, Richard; Stallings, Jonathan D

2016-01-01

This study sought to identify an optimal rodent bedding and cage-change interval to establish standard procedures for the IVC in our rodent vivarium. Disposable cages were prefilled with either corncob or α-cellulose bedding and were used to house 2 adult Sprague-Dawley rats (experimental condition) or contained no animals (control). Rats were observed and intracage ammonia levels measured daily for 21 d. Intracage ammonia accumulation became significant by day 8 in experimental cages containing α-cellulose bedding, whereas experimental cages containing corncob bedding did not reach detectable levels of ammonia until day 14. In all 3 experimental cages containing α-cellulose, ammonia exceeded 100 ppm (our maximum acceptable limit) by day 11. Two experimental corncob cages required changing at days 16 and 17, whereas the remaining cage containing corncob bedding lasted the entire 21 d without reaching the 100-ppm ammonia threshold. These data suggests that corncob bedding provides nearly twice the service life of α-cellulose bedding in the IVC system.

Improved lignin pyrolysis for phenolics production in a bubbling bed reactor--Effect of bed materials.

PubMed

Li, Dongbing; Briens, Cedric; Berruti, Franco

2015-01-01

Lignin pyrolysis was studied in a bubbling fluidized bed reactor equipped with a fractional condensation train, using nitrogen as the fluidization gas. The effect of different bed materials (silica sand, lignin char, activated lignin char, birch bark char, and foamed glass beads) on bio-oil yield and quality was investigated for a pyrolysis temperature of 550 °C. Results how that a bed of activated lignin char is preferable to the commonly used silica sand: pyrolysis of Kraft lignin with a bed of activated lignin char not only provides a pure char product, but also a higher dry bio-oil yield (with a relative increase of 43%), lower pyrolytic water production, and better bio-oil quality. The bio-oil obtained from Kraft lignin pyrolysis with a bed of activated lignin char has a lower average molecular weight, less tar, more phenolics, and less acidity than when sand is used as bed material. Copyright © 2015 Elsevier Ltd. All rights reserved.

The importance of body image concerns in overweight and normal weight individuals with binge eating disorder.

PubMed

Yiu, Angelina; Murray, Susan M; Arlt, Jean M; Eneva, Kalina T; Chen, Eunice Y

2017-09-01

Body image concerns in binge eating disorder (BED) have been examined almost exclusively in overweight individuals with BED. The current study extends past research by including overweight and normal weight BED and non-BED groups to assess the multifactorial construct of body image using subscales of the Eating Disorder Examination 16.0 (EDE-16.0) and a Body Comparison Task. Independent of weight status and when controlling for age and race, women with BED are distinguished from those without BED by significantly greater overvaluation of shape and weight on the EDE-16.0 and significantly reduced weight satisfaction after a Body Comparison Task. Both BED diagnosis and weight status were independently associated with Weight Concern and Shape Concern subscales on the EDE-16.0. Taken together, these data provide further support for the consideration of body image concerns in the diagnostic criteria for BED. Copyright © 2017 Elsevier Ltd. All rights reserved.

Testing the Bed-Blocking Hypothesis: Does Nursing and Care Home Supply Reduce Delayed Hospital Discharges?

PubMed Central

Gaughan, James; Gravelle, Hugh; Siciliani, Luigi

2015-01-01

Hospital bed-blocking occurs when hospital patients are ready to be discharged to a nursing home, but no place is available, so that hospital care acts as a more costly substitute for long-term care. We investigate the extent to which greater supply of nursing home beds or lower prices can reduce hospital bed-blocking using a new Local Authority (LA) level administrative data from England on hospital delayed discharges in 2009–2013. The results suggest that delayed discharges respond to the availability of care home beds, but the effect is modest: an increase in care home beds by 10% (250 additional beds per LA) would reduce social care delayed discharges by about 6–9%. We also find strong evidence of spillover effects across LAs: more care home beds or fewer patients aged over 65 years in nearby LAs are associated with fewer delayed discharges. © 2015 The Authors. Health Economics Published by John Wiley & Sons Ltd. PMID:25760581

Bed-sharing, breastfeeding and maternal moods in Barbados.

PubMed

Galler, Janina R; Harrison, Robert H; Ramsey, Frank

2006-12-01

Bed-sharing among Barbadian mothers and infants was studied in relationship to maternal and infant characteristics. This prospective study followed 226 healthy, well-nourished mother-infant dyads at birth, 7 weeks, 3 months, and 6 months postpartum. At each age, approximately half of the infants shared the same beds as their mothers. Bed-sharing was associated with demographic characteristics, especially fewer home conveniences, and also maternal characteristics, including less information seeking by the mother and younger maternal age at first pregnancy. Bed-sharing was also associated with lower infant birth weights. Maternal moods were significantly correlated with bed-sharing, such that mothers who reported having more despair and anxiety were also more likely to sleep with their infants. Bed-sharing was also significantly associated with increased breastfeeding at all infant ages, but this relationship was no longer significant once the effects of maternal moods were controlled. This study emphasizes the importance of assessing maternal moods in studies evaluating the risk and benefits of bed-sharing.

Assessment of the Coal-Bed Gas Total Petroleum System in the Cook Inlet-Susitna region, south-central Alaska

USGS Publications Warehouse

Rouse, William A.; Houseknecht, David W.

2012-01-01

The Cook Inlet-Susitna region of south-central Alaska contains large quantities of gas-bearing coal of Tertiary age. The U.S. Geological Survey in 2011 completed an assessment of undiscovered, technically recoverable coal-bed gas resources underlying the Cook Inlet-Susitna region based on the total petroleum system (TPS) concept. The Cook Inlet Coal-Bed Gas TPS covers about 9,600,000 acres and comprises the Cook Inlet basin, Matanuska Valley, and Susitna lowland. The TPS contains one assessment unit (AU) that was evaluated for coal-bed gas resources between 1,000 and 6,000 feet in depth over an area of about 8,500,000 acres. Coal beds, which serve as both the source and reservoir for natural gas in the AU, were deposited during Paleocene-Pliocene time in mires associated with a large trunk-tributary fluvial system. Thickness of individual coal beds ranges from a few inches to more than 50 feet, with cumulative coal thickness of more than 800 feet in the western part of the basin. Coal rank ranges from lignite to subbituminous, with vitrinite reflectance values less than 0.6 percent throughout much of the AU. The AU is considered hypothetical because only a few wells in the Matanuska Valley have tested the coal-bed reservoirs, so the use of analog coal-bed gas production data was necessary for this assessment. In order to estimate reserves that might be added in the next 30 years, coal beds of the Upper Fort Union Formation in the Powder River Basin of Wyoming and Montana were selected as the production analog for Tertiary coal beds in the Cook Inlet-Susitna region. Upper Fort Union coal beds have similar rank (lignite to subbituminous), range of thickness, and coal-quality characteristics as coal beds of the Tertiary Kenai Group. By use of this analog, the mean total estimate of undiscovered coal-bed gas in the Tertiary Coal-Bed Gas AU is 4.674 trillion cubic feet (TCF) of gas.

CTR Fuel recovery system using regeneration of a molecular sieve drying bed

DOEpatents

Folkers, Charles L.

1981-01-01

A primary molecular sieve drying bed is regenerated by circulating a hot inert gas through the heated primary bed to desorb water held on the bed. The inert gas plus water vapor is then cooled and passed through an auxiliary molecular sieve bed which adsorbs the water originally desorbed from the primary bed. The main advantage of the regeneration technique is that the partial pressure of water can be reduced to the 10.sup.-9 atm. range. This is significant in certain CTR applications where tritiated water (T.sub.2 O, HTO) must be collected and kept at very low partial pressure.

Behavioral Responses of the Bed Bug to Permethrin-Impregnated ActiveGuard™ Fabric.

PubMed

Jones, Susan C; Bryant, Joshua L; Harrison, Scott A

2013-06-07

ActiveGuard™ Mattress Liners have been used to control house dust mites, and they also are commercially available as an integrated pest management tool for use against bed bugs (Cimex lectularius). The aim of our study was to evaluate responses of numerous populations of the bed bug to the permethrin-impregnated fabric, with particular regard to contact toxicity, repellency, and feeding inhibition. Continuous exposure to ActiveGuard fabric resulted in rapid intoxication for three of four populations, with 87 to 100% of moderately pyrethroid-resistant and susceptible bed bugs succumbing by 1 d. In comparison, a highly resistant population reached 22% mortality at 10 d. Video data revealed that bed bugs readily traversed ActiveGuard fabric and spent a considerable amount of time moving about and resting on it during a 12-h period. ActiveGuard fabric was non-repellent to bed bugs from five tested populations. Furthermore, significantly fewer bed bugs successfully fed to repletion through ActiveGuard fabric than through blank fabric for the five populations. With just 30 min of feeding exposure, mortality ranged from 4% to 83%, depending upon the bed bug strain. These laboratory studies indicate that ActiveGuard liners adversely affected bed bugs from diverse populations.

Effect of Sand and Sawdust Bedding Materials on the Fecal Prevalence of Escherichia coli O157:H7 in Dairy Cows

PubMed Central

LeJeune, Jeffrey T.; Kauffman, Michael D.

2005-01-01

Farm management practices that reduce the prevalence of food-borne pathogens in live animals are predicted to enhance food safety. To ascertain the potential role of livestock bedding in the ecology and epidemiology of Escherichia coli O157:H7 on farms, the survival of this pathogen in used-sand and used-sawdust dairy cow bedding was determined. Additionally, a longitudinal study of mature dairy cattle housed on 20 commercial dairy farms was conducted to compare the prevalence of E. coli O157:H7 in cattle bedded on sand to that in cattle bedded on sawdust. E. coli O157:H7 persisted at higher concentrations in used-sawdust bedding than in used-sand bedding. The overall average herd level prevalence (3.1 versus 1.4%) and the number of sample days yielding any tests of feces positive for E. coli O157:H7 (22 of 60 days versus 13 of 60 days) were higher in sawdust-bedded herds. The choice of bedding material used to house mature dairy cows may impact the prevalence of E. coli O157:H7 on dairy farms. PMID:15640205

Multiple sources for late-Holocene tsunamis at Discovery Bay, Washington State, USA

USGS Publications Warehouse

Williams, H.F.L.; Hutchinson, I.; Nelson, A.R.

2005-01-01

Nine muddy sand beds interrupt a 2500-yr-old sequence of peat deposits beneath a tidal marsh at the head of Discovery Bay on the south shore of the Strait of Juan de Fuca, Washington. An inferred tsunami origin for the sand beds is assessed by means of six criteria. Although all the sand beds contain marine diatoms and almost all the beds display internal stratification, the areal extent of the oldest beds is too limited to confirm their origin as tsunami deposits. The ages of four beds overlap with known late-Holocene tsunamis generated by plate-boundary earthquakes at the Cascadia subduction zone. Diatom assemblages in peat deposits bracketing these four beds do not indicate concurrent change in elevation at Discovery Bay. Diatoms in the peat bracketing a tsunami bed deposited about 1000 cal. yr BP indicate a few decimeters of submergence, suggesting deformation on a nearby upper-plate fault. Other beds may mark tsunamis caused by more distant upper-plate earthquakes or local submarine landslides triggered by earthquake shaking. Tsunamis from both subduction zone and upper-plate sources pose a significant hazard to shoreline areas in this region.

Implications of bed reduction in an acute psychiatric service.

PubMed

Bastiampillai, Tarun J; Bidargaddi, Niranjan P; Dhillon, Rohan S; Schrader, Geoffrey D; Strobel, Jörg E; Galley, Philip J

2010-10-04

To evaluate the impact of psychiatric inpatient bed closures, accompanied by a training program aimed at enhancing team effectiveness and incorporating data-driven practices, in a mental health service. Retrospective comparison of the changes in services within three consecutive financial years: baseline period - before bed reduction (2006-07); observation period - after bed reduction (2007-08); and intervention period - second year after bed reduction (2008-09). The study was conducted at Cramond Clinic, Queen Elizabeth Hospital, Adelaide. Length of stay, 28-day readmission rates, discharges, bed occupancy rates, emergency department (ED) presentations, ED waiting time, seclusions, locality of treatment, and follow-up in the community within 7days. Reduced bed numbers were associated with reduced length of stay, fewer referrals from the community and subsequently shorter waiting times in the ED, without significant change in readmission rates. A higher proportion of patients was treated in the local catchment area, with improved community follow-up and a significant reduction in inpatient seclusions. Our findings should reassure clinicians concerned about psychiatric bed numbers that service redesign with planned bed reductions will not necessarily affect clinical care, provided data literacy and team training programs are in place to ensure smooth transition of patients across ED, inpatient and community services.

Bed Bugs: Clinical Relevance and Control Options

PubMed Central

Dwyer, Dominic E.; Peñas, Pablo F.; Russell, Richard C.

2012-01-01

Summary: Since the late 1990s, bed bugs of the species Cimex lectularius and Cimex hemipterus have undergone a worldwide resurgence. These bed bugs are blood-sucking insects that readily bite humans. Cutaneous reactions may occur and can start out as small macular lesions that can develop into distinctive wheals of around 5 cm in diameter, which are accompanied by intense itching. Occasionally, bullous eruptions may result. If bed bugs are numerous, the patient can present with widespread urticaria or eythematous rashes. Often, bites occur in lines along the limbs. Over 40 pathogens have been detected in bed bugs, but there is no definitive evidence that they transmit any disease-causing organisms to humans. Anemia may result when bed bugs are numerous, and their allergens can trigger asthmatic reactions. The misuse of chemicals and other technologies for controlling bed bugs has the potential to have a deleterious impact on human health, while the insect itself can be the cause of significant psychological trauma. The control of bed bugs is challenging and should encompass a multidisciplinary approach utilizing nonchemical means of control and the judicious use of insecticides. For accommodation providers, risk management procedures should be implemented to reduce the potential of bed bug infestations. PMID:22232375

Investigation of the characteristics of a compact steam reformer integrated with a water-gas shift reactor

NASA Astrophysics Data System (ADS)

Seo, Yong-Seog; Seo, Dong-Joo; Seo, Yu-Taek; Yoon, Wang-Lai

The objective of this study is to investigate numerically a compact steam methane reforming (SMR) system integrated with a water-gas shift (WGS) reactor. Separate numerical models are established for the combustion part, SMR and WGS reaction bed. The concentration of species at the exits of the SMR and WGS bed, and the temperatures in the WGS bed are in good agreement with the measured data. Heat transfer to the catalyst beds and the catalytic reactions in the SMR and WGS catalyst bed are investigated as a function of the operation parameters. The conversion of methane at the exit of the SMR catalyst bed is calculated to be 87%, and the carbon monoxide concentration at the outlet of the WGS bed is estimated to be 0.45%. The effects of the cooling heat flux at the outside wall of the system and steam-to-carbon (S/C) ratio are also examined. As the cooling heat flux increases, both the methane conversion and carbon monoxide content are reduced in the SMR bed, and the carbon monoxide conversion is improved in the WGS bed. Both methane conversion and carbon dioxide reduction increase with increasing steam-to-carbon ratio.

Energy monitoring and analysis during deformation of bedded-sandstone: use of acoustic emission.

PubMed

Wasantha, P L P; Ranjith, P G; Shao, S S

2014-01-01

This paper investigates the mechanical behaviour and energy releasing characteristics of bedded-sandstone with bedding layers in different orientations, under uniaxial compression. Cylindrical sandstone specimens (54 mm diameter and 108 mm height) with bedding layers inclined at angles of 10°, 20°, 35°, 55°, and 83° to the minor principal stress direction, were produced to perform a series of Uniaxial Compressive Strength (UCS) tests. One of the two identical sample sets was fully-saturated with water before testing and the other set was tested under dry conditions. An acoustic emission system was employed in all the testing to monitor the acoustic energy release during the whole deformation process of specimens. From the test results, the critical joint orientation was observed as 55° for both dry and saturated samples and the peak-strength losses due to water were 15.56%, 20.06%, 13.5%, 13.2%, and 13.52% for the bedding orientations 10°, 20°, 35°, 55°, and 83°, respectively. The failure mechanisms for the specimens with bedding layers in 10°, 20° orientations showed splitting type failure, while the specimens with bedding layers in 55°, 83° orientations were failed by sliding along a weaker bedding layer. The failure mechanism for the specimens with bedding layers in 35° orientation showed a mixed failure mode of both splitting and sliding types. Analysis of the acoustic energy, captured from the acoustic emission detection system, revealed that the acoustic energy release is considerably higher in dry specimens than that of the saturated specimens at any bedding orientation. In addition, higher energy release was observed for specimens with bedding layers oriented in shallow angles (which were undergoing splitting type failures), whereas specimens with steeply oriented bedding layers (which were undergoing sliding type failures) showed a comparatively less energy release under both dry and saturated conditions. Moreover, a considerable amount of energy dissipation before the ultimate failure was observed for specimens with bedding layers oriented in shallow angles under both dry and saturated conditions. These results confirm that when rock having bedding layers inclined in shallow angles the failures could be more violent and devastative than the failures of rock with steeply oriented bedding layers. Copyright © 2013 Elsevier B.V. All rights reserved.

Astronomical cycle origin of bedded chert: A middle Triassic bedded chert sequence, Inuyama, Japan

NASA Astrophysics Data System (ADS)

Ikeda, Masayuki; Tada, Ryuji; Sakuma, Hironobu

2010-09-01

Astronomical forcing is one of the main drivers of climate change, and astronomical cyclicity recorded in sediments provides a clue to understand the dynamics of the global climate system. Bedded cherts consist of rhythmic alternations of chert and shale beds. Although previous studies have hypothesized that the origin of bedded chert is related to astronomical cycles (e.g. Fischer, 1976; Hori et al., 1993), conclusive proof remains elusive. To explore this possibility, we established a continuous, high-resolution lithostratigraphy of middle Triassic bedded chert in Central Japan. The average duration of each chert-shale couplet is 20 kyr, similar to that of the precession cycle. Spectral analysis of a bed number series of thickness variations in chert beds was performed assuming that each chert-shale couplet represents a 20-kyr precession cycle. The results reveal cycles involving approximately 200, 20, 5, and 2-3 beds, corresponding to periodicities of approximately 4000, 400, 100, and 40-60 kyr, respectively. By further assuming that the 20-bed cycle represents a 405-kyr eccentricity cycle of constant and stable periodicity, we converted the bed number series to a time series. Spectral analysis of the time series revealed distinct periodicities of 3600, 117, 97, and 38 kyr, in addition to 405 kyr. Besides 3600 kyr, these periodicities agree well with the 120, 95, and 37 kyr periodicities for eccentricity cycles and the obliquity cycle during the Triassic. Moreover, we detected amplitude modulation of the approximately 100-kyr cycle of thickness variations in chert beds with a 405-kyr periodicity, which may correspond to amplitude modulation of 100-kyr climatic precession cycle with the 405-kyr periodicity. The approximately 3600-kyr periodicity described above and 1800-kyr periodicity manifested as the amplitude modulation of the 405-kyr cycle are correlated to present-day long-term eccentricity cycles of 2400 and 4800 kyr evolved by chaotic behavior of solar planets. Collectively, these similarities in the periodicities of dominant cycles, their hierarchy, and the nature of amplitude modulation of cycles in chert bed thickness with those of astronomical cycles strongly support the hypothesis that the sedimentary rhythm of bedded chert is paced by astronomical cycles, thereby indicating the potential of bedded chert as a template for a Mesozoic cyclostratigraphy.

Factors affecting the geochemistry of a thick, subbituminous coal bed in the Powder River Basin: volcanic, detrital, and peat-forming processes

USGS Publications Warehouse

Crowley, S.S.; Ruppert, L.F.; Belkin, H.E.; Stanton, R.W.; Moore, T.A.

1993-01-01

The inorganic geochemistry and mineralogy of three cores from the Anderson-Dietz 1 coal bed, a 15.2-m-thick subbituminous coal bed in the Tongue River Member (Paleocene) of the Fort Union Formation, were examined (1) to determine if the cores could be correlated by geochemical composition alone over a total distance of 2 km and (2) to identify the major factors that influenced the geochemistry of the coal bed. Chemical data (46 elements on a coal-ash basis) for 81 coal samples and 4 carbonaceous rock samples, with most samples representing a 0.6-m-thick (2-ft) interval of core, were grouped into compositional clusters by means of cluster analysis. Seven major clusters were produced; two of these clusters can be used to correlate the coal bed throughout the study area. Data from scanning electron and optical microscope analyses indicate that several factors influenced the geochemistry of the Anderson-Dietz 1 coal bed. The majority of mineral grains in the coal bed are interpreted to be detrital (water borne); evidence includes the presence of rounded to subrounded quartz grains having two-phase, aqueous fluid inclusions characteristic of hydrothermal or low-to-moderate grade metamorphic quartz. These quartz grains are found throughout the coal bed but are most abundant in samples from the midpart of the bed, which was influenced by detrital input associated with the deposition of the clastic rocks that form the split between the Anderson and Dietz 1 coal beds 900 m to the east of the study area. In addition to the detrital minerals mentioned above, volcanic ash that was fluvially transported to the sites of peat deposition or possibly deposited as air-fall volcanic ash also affected the geochemistry of the coal bed. For example, crandallite(?), a mineral reported to form as an alteration product of volcanic ash, is found in seven samples from the coal bed. The presence of quartz grains containing silicate-melt inclusions in eight samples from the coal bed.provides further support for a volcanic ash component. Other factors that probably affected the geochemistry of the coal bed include (1) detrital input associated with the deposition of the roof rocks of the coal bed, (2) peat-forming processes and plant material, and (3) epigenetic ground-water flow. ?? 1993.

Television viewing, computer game playing, and Internet use and self-reported time to bed and time out of bed in secondary-school children.

PubMed

Van den Bulck, Jan

2004-02-01

To investigate the relationship between the presence of a television set, a gaming computer, and/or an Internet connection in the room of adolescents and television viewing, computer game playing, and Internet use on the one hand, and time to bed, time up, time spent in bed, and overall tiredness in first- and fourth-year secondary-school children on the other hand. A random sample of students from 15 schools in Flanders, Belgium, yielded 2546 children who completed a questionnaire with questions about media presence in bedrooms; volume of television viewing, computer game playing, and Internet use; time to bed and time up on average weekdays and average weekend days; and questions regarding the level of tiredness in the morning, at school, after a day at school, and after the weekend. Children with a television set in their rooms went to bed significantly later on weekdays and weekend days and got up significantly later on weekend days. Overall, they spent less time in bed on weekdays. Children with a gaming computer in their rooms went to bed significantly later on weekdays. On weekdays, they spent significantly less time in bed. Children who watched more television went to bed later on weekdays and weekend days and got up later on weekend days. They spent less time in bed on weekdays. They reported higher overall levels of being tired. Children who spent more time playing computer games went to bed later on weekdays and weekend days and got up later on weekend days. On weekdays, they actually got up significantly earlier. They spent less time in bed on weekdays and reported higher levels of tiredness. Children who spent more time using the Internet went to bed significantly later during the week and during the weekend. They got up later on weekend days. They spent less time in bed during the week and reported higher levels of tiredness. Going out was also significantly related to sleeping later and less. Concerns about media use should not be limited to television. Computer game playing and Internet use are related to sleep behavior as well. Leisure activities that are unstructured seem to be negatively related to good sleep patterns. Imposing more structure (eg, end times) might reduce impact.

Long-lasting insecticidal net source, ownership and use in the context of universal coverage: a household survey in eastern Rwanda.

PubMed

Kateera, Fredrick; Ingabire, Chantal M; Hakizimana, Emmanuel; Rulisa, Alexis; Karinda, Parfait; Grobusch, Martin P; Mutesa, Leon; van Vugt, Michèle; Mens, Petra F

2015-10-06

Universal long-lasting insecticidal net (LLIN) coverage (ULC) has reduced malaria morbidity and mortality across Africa. Although information is available on bed net use in specific groups, such as pregnant women and children under 5 years, there is paucity of data on their use among the general population. Bed net source, ownership and determinants of use among individuals from households in an eastern Rwanda community 8 months after a ULC were characterized. Using household-based, interviewer-administered questionnaires and interviewer-direct observations, data on bed net source, ownership and key determinants of net use, including demographics, socio-economic status indicators, house structure characteristics, as well as of bed net quantity, type and integrity, were collected from 1400 randomly selected households. Univariate and mixed effects logistic regression modelling was done to assess for determinants of bed net use. A total of 1410 households and 6598 individuals were included in the study. Overall, the proportion of households with at least one net was 92 % while bed net usage was reported among 72 % of household members. Of the households surveyed, a total ownership of 2768 nets was reported, of which about 96 % were reportedly LLINs received from the ULC. By interviewer-physical observation, 88 % of the nets owned were of the LLIN type with the remaining 12 % did not carry any mark to enable type recognition. The odds of bed net use were significantly lower among males and individuals: from households of low socio-economic status, from households with

21 CFR 880.6060 - Medical disposable bedding.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Medical disposable bedding. 880.6060 Section 880...) MEDICAL DEVICES GENERAL HOSPITAL AND PERSONAL USE DEVICES General Hospital and Personal Use Miscellaneous Devices § 880.6060 Medical disposable bedding. (a) Identification. Medical disposable bedding is a device...

21 CFR 880.6060 - Medical disposable bedding.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Medical disposable bedding. 880.6060 Section 880...) MEDICAL DEVICES GENERAL HOSPITAL AND PERSONAL USE DEVICES General Hospital and Personal Use Miscellaneous Devices § 880.6060 Medical disposable bedding. (a) Identification. Medical disposable bedding is a device...

Chemical, physical, and environmental properties of pelleted newspaper compared to wheat straw and wood shavings as bedding for horses.

PubMed

Ward, P L; Wohlt, J E; Katz, S E

2001-06-01

Two experiments were conducted comparing pelleted recycled newspaper (PN) to wheat straw (S) and kiln-dried pine wood shavings (WS) as an animal bedding material. Adult horses housed 20 to 21 h/d in boxstalls served as the animal model for comparisons. In Exp. 1 eight boxstalls, each housing one horse, were each bedded with two types of PN (0.32 and 0.64 x 2.54 cm), S, and WS over four 5-d periods (replicated 4 x 4 Latin square). Initial amounts of bedding materials surpassed most commercial conditions, but stalls were cleaned daily of feces only and additional clean bedding was added as needed to maintain animal cleanliness, thus challenging the bedding properties of each material. In Exp. 2 nine boxstalls were bedded with PN (0.32 x 2.54 cm), S, and WS over three 14-d periods (three 3 x 3 Latin squares) during summer and autumn. Feces and wet spots were removed daily and clean bedding was added to reestablish working volume and simulate commercial conditions. In Exp. 1 and 2 daily additions of clean bedding varied (P < 0.05) with material (S > WS > PN). The higher water-holding capacity of PN and WS contributed to fewer bedding replacements. Usage of each material was greater (P < 0.05) during the autumn; PN had the greatest increase. Type of material and season also influenced bedding environment. Bedding pH increased (P < 0.05) with use and was highest in PN and lowest in S. Higher concentrations of breathable NH3 N were present in stalls bedded with PN and during autumn. Higher pH of used PN and decreased ventilation due to closed doors and windows during autumn were contributing factors. Season, type of bedding, and duration of its use affected (P < 0.05) numbers as well as species of microorganisms present in the breathing zone, nasal cavity, and on the leg of the horse. Clean and used WS contained greater (P < 0.05) quantities of particle fines, but with 5 d of use, particle fines in PN also increased. Quantities of breathable dust during cleaning of stalls varied (P < 0.05) with material and duration of its use; dust peaked at d 7 with PN but continued to decrease with S and to increase with WS through d 14. These data indicate that management of bedding materials varies with type of material and season of year. Use of PN as a bedding material has high potential.

The Effects of Long Duration Bed Rest as a Spaceflight Analogue on Resting State Sensorimotor Network Functional Connectivity and Neurocognitive Performance

NASA Technical Reports Server (NTRS)

Cassady, K.; Koppelmans, V.; Yuan, P.; Cooke, K.; De Dios, Y.; Stepanyan, V.; Szecsy, D.; Gadd, N.; Wood, S.; Reuter-Lorenz, P.;